Online gas monitoring and sampling during drilling of the INFLUINS borehole EF-FB 1/12 into the Thuringian Syncline, Germany

NASA Astrophysics Data System (ADS)

Görlitz, Marco; Abratis, Michael; Wiersberg, Thomas

2014-05-01

Online monitoring and sampling of drill mud gas (OLGA) was conducted during standard rotary drilling and core drilling of the INFLUINS borehole EF-FB 1/12 to gain information on the composition of gases and their distribution at depth within the Thuringian Syncline (Germany). The method can help to identify areas of enhanced permeability and/or porosity, open fractures, and other strata associated with gases at depth. The gas-loaded drill mud was continuously degassed in a modified gas-water separator, which was installed in the mud ditch in close distance to the drill mud outlet. The extracted gas phase was pumped in a nearby field laboratory for continuous on-line analysis. First information on the gas composition (H2, He, N2, O2, CO2, CH4, Ar, Kr) was available only few minutes after gas extraction. More than 40 gas samples were taken from the gas line during drilling and pumping tests for further laboratory studies. Enhanced concentration of methane, helium, hydrogen and carbon dioxide were detected in drill mud when the drill hole encountered gas-rich strata. Down to a depth of 620 m, the drill mud contained maximum concentration of 55 ppmv He, 1400 ppmv of CH4, 400 ppmv of hydrogen and 1.1 vol-% of CO2. The drilling mud gas composition is linked with the drilled strata. Buntsandstein and Muschelkalk show different formation gas composition and are therefore hydraulically separated. Except for helium, the overall abundance of formation gases in drilling mud is relatively low. We therefore consider the INFLUINS borehole to be dry. The correlation between hydrogen and helium and the relatively high helium abundance rules out any artificial origin of hydrogen and suggest a radiolytic origin of hydrogen. Values CH4/(C2H6/C3H8)

Elastomers in mud motors for oil field applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hendrik, J.

1997-08-01

Mud motors, the most frequently used downhole drilling motors in modern drilling systems, are described in their application and function. The elastomeric liner in a mud motor acts as a huge continuous seal. Important properties of elastomers such as chemical resistance, fatigue resistance, mechanical strength, abrasion resistance, bonding to steel and processability are discussed. Advantages and disadvantages of NBR, HNBR, FKM, TFEP, and EPDM elastomers for mud motor applications are briefly described. The importance of drilling fluids and their physical and chemical impact on motor elastomers are described. Drilling fluids are categorized in: oil based-, synthetic-, and water based. Resultsmore » of compatibility tests in the different drilling muds of the presented categories demonstrate the complexity of elastomer development. Elastomers with an equally good performance in all drilling muds are not available. Future developments and improvements are directed towards higher chemical resistance at higher service temperatures. This will be possible only with improved elastomer-to-metal bonding, increased mechanical and better dynamic properties.« less

Estimation of bioavailability of metals from drilling mud barite.

PubMed

Neff, Jerry M

2008-04-01

Drilling mud and associated drill cuttings are the largest volume wastes associated with drilling of oil and gas wells and often are discharged to the ocean from offshore drilling platforms. Barite (BaSO4) often is added as a weighting agent to drilling muds to counteract pressure in the geologic formations being drilled, preventing a blowout. Some commercial drilling mud barites contain elevated (compared to marine sediments) concentrations of several metals. The metals, if bioavailable, may harm the local marine ecosystem. The bioavailable fraction of metals is the fraction that dissolves from the nearly insoluble, solid barite into seawater or sediment porewater. Barite-seawater and barite-porewater distribution coefficients (Kd) were calculated for determining the predicted environmental concentration (PEC; the bioavailable fraction) of metals from drilling mud barite in the water column and sediments, respectively. Values for Kdbarite-seawater and Kdbarite-porewater were calculated for barium, cadmium, chromium, copper, mercury, lead, and zinc in different grades of barite. Log Kdbarite-seawater values were higher (solubility was lower) for metals in the produced water plume than log Kdbarite-porewater values for metals in sediments. The most soluble metals were cadmium and zinc and the least soluble were mercury and copper. Log Kd values can be used with data on concentrations of metals in barite and of barite in the drilling mud-cuttings plume and in bottom sediments to calculate PECseawater and PECsediment.

Effects of pore pressure and mud filtration on drilling rates in a permeable sandstone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Black, A.D.; DiBona, B.; Sandstrom, J.

1983-10-01

During laboratory drilling tests in a permeable sandstone, the effects of pore pressure and mud filtration on penetration rates were measured. Four water-base muds were used to drill four saturated sandstone samples. The drilling tests were conducted at constant borehole pressure with different back pressures maintained on the filtrate flowing from the bottom of the sandstone samples. Bit weight was also varied. Filtration rates were measured while drilling and with the bit off bottom and mud circulating. Penetration rates were found to be related to the difference between the filtration rates measured while drilling and circulating. There was no observedmore » correlation between standard API filtration measurements and penetration rate.« less

Effects of pore pressure and mud filtration on drilling rates in a permeable sandstone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Black, A.D.; Dearing, H.L.; DiBona, B.G.

1985-09-01

During laboratory drilling tests in a permeable sandstone, the effects of pore pressure and mud filtration on penetration rates were measured. Four water-based muds were used to drill four saturated sandstone samples. The drilling tests were conducted at constant borehole pressure while different backpressures were maintained on the filtrate flowing from the bottom of the sandstone samples. Bit weight was varied also. Filtration rates were measured while circulating mud during drilling and with the bit off bottom. Penetration rates were found to be related qualitatively to the difference between the filtration rates measured while drilling and circulating. There was nomore » observed correlation between standard API filtration measurements and penetration rate.« less

WETTABILITY AND PREDICTION OF OIL RECOVERY FROM RESERVOIRS DEVELOPED WITH MODERN DRILLING AND COMPLETION FLUIDS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jill S. Buckley; Norman r. Morrow

2002-06-01

This first semiannual report covers efforts to select the materials that will be used in this project. Discussions of crude oils, rocks, smooth mineral surfaces, and drilling mud additives are included in this report.

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Mud program. 250.1614 Section 250.1614 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1614 Mud program. (a) The quantities, characteristics, use, and testing of drilling mud and the related drilling procedures shall be designed and...

Development of environmental friendly lost circulation material from banana peel

NASA Astrophysics Data System (ADS)

Sauki, Arina; Hasan, Nur â.€˜Izzati; Naimi, Fardelen Binti Md; Othman, Nur Hidayati

2017-12-01

Loss of expensive mud could lead to major financial problem in executing a drilling project and is one of the biggest problems that need to be tackled during drilling. Synthetic Based Mud (SBM) is the most stable state of the art drilling mud used in current drilling technologies. However, the problem with lost circulation is still inevitable. The focus of this project is to develop a new potential waste material from banana peel in order to combat lost circulation in SBM. Standard industrial Lost Circulation Material (LCM) is used to compare the performance of banana peel as LCM in SBM. The effects of different sizing of banana peels (600 micron, 300 micron and 100 micron) were studied on the rheological and filtration properties of SBM and the bridging performance of banana peel as LCM additive. The tests were conducted using viscometer, HTHP filter press and sand bed tester. Thermal analysis of banana peel was also studied using TGA. According to the results obtained, 300 and 100 micron size of banana peel LCM exhibited an improved bridging performance by 65% as compared to industrial LCM. However, banana peel LCM with the size of 600 micron failed to act as LCM due to the total invasion of mud into the sand bed.

Invasion of drilling mud into gas-hydrate-bearing sediments. Part I: effect of drilling mud properties

NASA Astrophysics Data System (ADS)

Ning, Fulong; Zhang, Keni; Wu, Nengyou; Zhang, Ling; Li, Gang; Jiang, Guosheng; Yu, Yibing; Liu, Li; Qin, Yinghong

2013-06-01

To our knowledge, this study is the first to perform a numerical simulation and analysis of the dynamic behaviour of drilling mud invasion into oceanic gas-hydrate-bearing sediment (GHBS) and to consider the effects of such an invasion on borehole stability and the reliability of well logging. As a case study, the simulation background sets up the conditions of mud temperature over hydrate equilibrium temperature and overbalanced drilling, considering the first Chinese expedition to drill gas hydrate (GMGS-1). The results show that dissociating gas may form secondary hydrates in the sediment around borehole by the combined effects of increased pore pressure (caused by mud invasion and flow resistance), endothermic cooling that accompanies hydrate dissociation compounded by the Joule-Thompson effect and the lagged effect of heat transfer in sediments. The secondary hydrate ring around the borehole may be more highly saturated than the in situ sediment. Mud invasion in GHBS is a dynamic process of thermal, fluid (mud invasion), chemical (hydrate dissociation and reformation) and mechanical couplings. All of these factors interact and influence the pore pressure, flow ability, saturation of fluid and hydrates, mechanical parameters and electrical properties of sediments around the borehole, thereby having a strong effect on borehole stability and the results of well logging. The effect is particularly clear in the borehole SH7 of GMGS-1 project. The borehole collapse and resistivity distortion were observed during practical drilling and wireline logging operations in borehole SH7 of the GMGS-1.mud density (i.e. the corresponding borehole pressure), temperature and salinity have a marked influence on the dynamics of mud invasion and on hydrate stability. Therefore, perhaps well-logging distortion caused by mud invasion, hydrate dissociation and reformation should be considered for identifying and evaluating gas hydrate reservoirs. And some suitable drilling measurements need to be adopted to reduce the risk of well-logging distortion and borehole instability.

Real time drilling mud gas response to small-moderate earthquakes in Wenchuan earthquake Scientific Drilling Hole-1 in SW China

NASA Astrophysics Data System (ADS)

Gong, Zheng; Li, Haibing; Tang, Lijun; Lao, Changling; Zhang, Lei; Li, Li

2017-05-01

We investigated the real time drilling mud gas of the Wenchuan earthquake Fault Scientific Drilling Hole-1 and their responses to 3918 small-moderate aftershocks happened in the Longmenshan fault zone. Gas profiles for Ar, CH4, He, 222Rn, CO2, H2, N2, O2 are obtained. Seismic wave amplitude, energy density and static strain are calculated to evaluate their power of influence to the drilling site. Mud gases two hours before and after each earthquake are carefully analyzed. In total, 25 aftershocks have major mud gas response, the mud gas concentrations vary dramatically immediately or minutes after the earthquakes. Different gas species respond to earthquakes in different manners according to local lithology encountered during the drill. The gas variations are likely controlled by dynamic stress changes, rather than static stress changes. They have the seismic energy density between 10-5 and 1.0 J/m3 whereas the static strain are mostly less than 10-8. We suggest that the limitation of the gas sources and the high hydraulic diffusivity of the newly ruptured fault zone could have inhibited the drilling mud gas behaviors, they are only able to respond to a small portion of the aftershocks. This work is important for the understanding of earthquake related hydrological changes.

Utilization of drilling cuttings with extraction of ground for recultivation of disturbed soils

NASA Astrophysics Data System (ADS)

Gaevaya, E. V.; Bogaychuk, Y. E.; Tarasova, S. S.; Skipin, L. N.; Zakharova, E. V.

2017-10-01

Drilling of wells is connected with formation of the bore mud represented by the drill cutting with waste drilling mud. Bore mud has negative physical-chemical, physical and chemical properties: high content of salts, increased alkalinity, ash structure, soil overcrust, low airing, weak filterability and so on. In case of phosphogypsum adding to the bore mud, pH level decreases from the alkaline (10.5 U) to weakly alkaline 7.6 U, decrease of pH is connected with the influence of phosphogypsum acidity and neutralization of the more mud. Concentration of chloride ions and sulphate ions in reclaimed bore mud was 70±7 and 456±46 correspondingly. Presence of oil products in received soil was 198.0-219.0 mg/kg. When adding phosphogypsum, sand, sorbent and humic formulation «Rostok» to the bore mud, it has shown good germinating ability of cultures- phytomeliorants (93,3%). 100% germinating ability was observed in meadow grass with a height of overground sprouts 10.7 cm, germinating ability of red fescue was 80% with height of overground sprouts 9.6 cm.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon Tibbitts; Arnis Judzis

2002-07-01

This document details the progress to date on the OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE -- A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING contract for the quarter starting April 2002 through June 2002. Even though we are awaiting the optimization portion of the testing program, accomplishments include the following: (1) Presentation material was provided to the DOE/NETL project manager (Dr. John Rogers) for the DOE exhibit at the 2002 Offshore Technology Conference. (2) Two meeting at Smith International and one at Andergauge in Houston were held to investigate their interest in joining the Mud Hammer Performancemore » study. (3) SDS Digger Tools (Task 3 Benchmarking participant) apparently has not negotiated a commercial deal with Halliburton on the supply of fluid hammers to the oil and gas business. (4) TerraTek is awaiting progress by Novatek (a DOE contractor) on the redesign and development of their next hammer tool. Their delay will require an extension to TerraTek's contracted program. (5) Smith International has sufficient interest in the program to start engineering and chroming of collars for testing at TerraTek. (6) Shell's Brian Tarr has agreed to join the Industry Advisory Group for the DOE project. The addition of Brian Tarr is welcomed as he has numerous years of experience with the Novatek tool and was involved in the early tests in Europe while with Mobil Oil. (7) Conoco's field trial of the Smith fluid hammer for an application in Vietnam was organized and has contributed to the increased interest in their tool.« less

Mineralogy of Gas Hydrate Bearing Sediment in Green Canyon Block 955 Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Heber, R.; Kinash, N.; Cook, A.; Sawyer, D.; Sheets, J.; Johnson, J. E.

2017-12-01

Natural gas hydrates are of interest as a future hydrocarbon source, however, the formation and physical properties of such systems are not fully understood. In May 2017, the University of Texas drilled two holes in Green Canyon Block 955, northern Gulf of Mexico to collect pressurized core from a thick, 100 m accumulation of gas hydrate in a silt dominated submarine canyon levee system. The expedition, known as UT-GOM2-01, collected 21, 10-m pressure cores from Holes H002 and H005. Approximately half of the cores successfully pressurized and were fully recovered. Unsuccessful cores that did not pressurize generally had low core recovery. By analyzing the sediment composition in known gas hydrate reservoirs, we can construct a more detailed picture of how and why gas hydrates accumulate, as mineralogy can affect physical properties such as porosity and permeability as well as geophysical measurements such as resistivity. Using X-ray diffraction (XRD) on bulk sediment powders, we determined the bulk mineralogy of the samples. Moreover, we investigated drilling mud contamination using XRD and light optical analysis. In some cores, contamination was easily recognized visually as dense sludge between the core barrel and the recovered sediment core, however drilling mud is best observed both along the liner and interbedded within the sediment on X-ray computed tomography scans. To fully identify the presence and influence of drilling mud, we use XRD to analyze samples on cores collected both while drilling mud was used in hole and when only seawater was used in hole and consider the density anomalies observed on the XCT scans. The preliminary XRD light optical microscopy results show that the silt-dominated reservoir is primarily composed of quartz, with minor alkali feldspar, amphibole, muscovite, dolomite, and calcite. Samples from intervals with suspected drilling mud contamination show a similar composition, but with the addition of barite, a common component in drilling mud. Understanding why contamination occurs will improve the coring process and ensure maximum recovery in the future. The XRD data also show the presence of 7-angstrom clay minerals, most likely chlorite and serpentine, but more analysis is required in order to verify the identification and to establish relative abundances of each mineral.

Elemental composition of airborne dust in the Shale Shaker House during an offshore drilling operation.

PubMed

Hansen, A B; Larsen, E; Hansen, L V; Lyngsaae, M; Kunze, H

1991-12-01

During 2 days of an offshore drilling operation in the North Sea, 16 airborne dust samples from the atmosphere of the Shale Shaker House were collected onto filters. During this operation, drilling mud composed of a water slurry of barite (BaSO4) together with minor amounts of additives, among them chrome lignosulphonate and chrome lignite, was circulated between the borehole and the Shale Shaker House. The concentration of airborne dust in the atmosphere was determined and the elemental composition of the particles analysed by both PIXE (proton-induced X-ray emission) and ICP-MS (inductively coupled plasma-mass spectrometry). The total amount of dust collected varied from 0.04 to 1.41 mg m-3 with barium (Ba) as the single most abundant element. The open shale shakers turned out to be the major cause of generation of dust from the solid components of the drilling mud.

Installation Restoration Program Phase 1 - Records Search, O’Hare Air Reserve Forces Facility, Illinois

DTIC Science & Technology

1983-12-01

clarifiers, activated sludge units, trickling filters, aerobic and anaerobic digesters, and various dowatering devices and recommendations for...for locations of water- bearing fractures. Additional responsibilities included drilling with mud and air rotary drilling rigs as well as bucket auger...interpretation. Also conducted earth resistivity surveys in Georgia and Alabama Piedmont Provinces for locations of water- bearing fractures. Additional

Continuous chain bit with downhole cycling capability

DOEpatents

Ritter, Don F.; St. Clair, Jack A.; Togami, Henry K.

1983-01-01

A continuous chain bit for hard rock drilling is capable of downhole cycling. A drill head assembly moves axially relative to a support body while the chain on the head assembly is held in position so that the bodily movement of the chain cycles the chain to present new composite links for drilling. A pair of spring fingers on opposite sides of the chain hold the chain against movement. The chain is held in tension by a spring-biased tensioning bar. A head at the working end of the chain supports the working links. The chain is centered by a reversing pawl and piston actuated by the pressure of the drilling mud. Detent pins lock the head assembly with respect to the support body and are also operated by the drilling mud pressure. A restricted nozzle with a divergent outlet sprays drilling mud into the cavity to remove debris. Indication of the centered position of the chain is provided by noting a low pressure reading indicating proper alignment of drilling mud slots on the links with the corresponding feed branches.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon Tibbitts; Arnis Judzis

2001-10-01

This document details the progress to date on the OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE -- A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING contract for the quarter starting July 2001 through September 2001. Accomplishments to date include the following: TerraTek highlighted DOE's National Energy Technology Laboratory effort on Mud Hammer Optimization at the recent Annual Conference and Exhibition for the Society of Petroleum Engineers. The original exhibit scheduled by NETL was canceled due to events surrounding the September tragedies in the US. TerraTek has completed analysis of drilling performance (rates of penetration, hydraulics, etc.) for themore » Phase One testing which was completed at the beginning of July. TerraTek jointly with the Industry Advisory Board for this project and DOE/NETL conducted a lessons learned meeting to transfer technology vital for the next series of performance tests. Both hammer suppliers benefited from the testing program and are committed to pursue equipment improvements and ''optimization'' in accordance with the scope of work. An abstract for a proposed publication by the society of Petroleum Engineers/International Association of Drilling Contractors jointly sponsored Drilling Conference was accepted as an alternate paper. Technology transfer is encouraged by the DOE in this program, thus plans are underway to prepare the paper for this prestigious venue.« less

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon Tibbitts; Arnis Judzis

2001-04-01

This document details the progress to date on the OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE -- A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING contract for the quarter starting January 2001 through March 2001. Accomplishments to date include the following: (1) On January 9th of 2001, details of the Mud Hammer Drilling Performance Testing Project were presented at a ''kick-off'' meeting held in Morgantown. (2) A preliminary test program was formulated and prepared for presentation at a meeting of the advisory board in Houston on the 8th of February. (3) The meeting was held with the advisorymore » board reviewing the test program in detail. (4) Consensus was achieved and the approved test program was initiated after thorough discussion. (5) This new program outlined the details of the drilling tests as well as scheduling the test program for the weeks of 14th and 21st of May 2001. (6) All the tasks were initiated for a completion to coincide with the test schedule. (7) By the end of March the hardware had been designed and the majority was either being fabricated or completed. (8) The rock was received and cored into cylinders.« less

Stress and Pore Pressure Measurement in IODP Riser Drilling: An Example from Expedition 319, Kumano Basin offshore SW Honshu, Japan

NASA Astrophysics Data System (ADS)

Saffer, D. M.; McNeill, L. C.; Byrne, T. B.; Araki, E.; Flemings, P. B.; Conin, M.; Eguchi, N. O.; Takahashi, K.; Toczko, S.; Boutt, D. F.; Doan, M.; Kano, Y.; Ito, T.; Lin, W.

2009-12-01

In summer 2009, Integrated Ocean Drilling Program (IODP) Expedition 319 drilled a 1600 m deep riser borehole (Site C0009) in the Kumano Basin offshore SW Japan, to investigate the properties, structure and state of stress in the hanging wall above the subduction plate boundary. The first riser-based scientific drilling in IODP history allowed us to make several new scientific measurements including in situ stress magnitude, pore pressure and permeability using the Modular Formation Dynamics Tester (MDT) wireline tool, and measurement of minimum stress magnitude from Leak-off Tests (LOT). In addition, continuous monitoring of mud weight, mud gas, annular pressure, and mud losses provided data to constrain formation pore fluid pressure and stress. At Site C0009, we conducted 2 LOTs below a casing shoe at 708.6 m depth and 11 successful MDT measurements, including 9 single probe tests to measure pore pressure and fluid mobility and 2 dual packer tests: 1 to measure permeability by a drawdown test, and 1 to measure in situ stress. Measured pore pressures are approximately hydrostatic to 1463.7 m depth. We observed only minor gas shows when drilling ahead (as in-place methane was liberated from the rock at the bit) but little or no gas during pipe connections. This indicates that the borehole mud pressure exceeded the formation pore pressure, and is consistent with the MDT measurements. Permeabilities range from ~10-16 m2 - 10-14 m2, and the observed variation is consistent with lithologic changes defined in gamma ray logs. The MDT measurement at 874.3 mbsf and the LOT at 708.6 m yield values for the least principal stress of 34.8 MPa and 30.2 MPa, respectively. Both are less than the vertical stress (Sv) computed from density logs. Partial mud circulation losses occurred when the borehole mud pressure exceeded the leak-off stress measured at the base of the casing shoe; this provides an additional indirect constraint on Shmin magnitude. Mud pressure slightly in excess of the leak-off stress may have also generated poorly-developed drilling-induced tensile fractures (DITF) observed in resistivity image logs between ~750 - 1000 m. From the presence of DITF, Shmin measurements, and assuming a rock tensile strength of 1 MPa, we determine that SHmax is 35.1 MPa for the MDT stress measurement, and 30.2 MPa for the LOT. Using the MDT measurement of Shmin, the resulting principal stress magnitudes define a strike-slip faulting regime with effective stresses of Shmax’ = 14 MPa, Sv' = 7.3 MPa, and Shmin’ = 6.4 MPa. In contrast, using the LOT measurement of Shmin, the stress magnitudes indicate a normal faulting regime in which Sv’ = 6.2 MPa, Shmax’ = 2.8 MPa, and Shmin’ = 2.6 MPa.

Polyamine sensitization in offshore workers handling drilling muds.

PubMed

Ormerod, A D; Wakeel, R A; Mann, T A; Main, R A; Aldridge, R D

1989-11-01

Oil-based mud, a complex mixture containing amines in emulsifiers, is used in offshore drilling operations. It is a skin irritant that occasionally gives rise to allergic contact sensitivity. In patch testing patients with allergy to drilling mud, we have identified polyamine (diethylenetriamine and triethylenetetramine) sensitivity in 5 patients. All 5 patients were also allergic to emulsifiers. These emulsifiers are cross-linked fatty acid amido-amines, in which unreacted amine groups are thought to cross-sensitize with these constituent polyamines. Cross-reactivity between ethylenediamine, diethylenetetramine and triethylenetetramine was found in 9 subjects.

Drill Ship Glomar Java Sea, O.N. 568182, Capsizing and Sinking in the South China Sea, on 25 October 1983 with Multiple Loss of Life

DTIC Science & Technology

1985-05-28

drilling mud tanks . * Continuing forward were the mud and cement pump room, bulk dry mud and cement storage , and ballast tanks . Also in the forward...including double bottom tanks throughout most of the vessel’s length, storage areas, and workshops. Above the main deck, aft, above the machinery spaces...elevated flat for storage of well casing. The drill floor with the draw works, rotary and associated equipment, was located at the superstructure deck

Optimization of Mud Hammer Drilling Performance--A Program to Benchmark the Viability of Advanced Mud Hammer Drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnis Judzis

2006-03-01

Operators continue to look for ways to improve hard rock drilling performance through emerging technologies. A consortium of Department of Energy, operator and industry participants put together an effort to test and optimize mud driven fluid hammers as one emerging technology that has shown promise to increase penetration rates in hard rock. The thrust of this program has been to test and record the performance of fluid hammers in full scale test conditions including, hard formations at simulated depth, high density/high solids drilling muds, and realistic fluid power levels. This paper details the testing and results of testing two 7more » 3/4 inch diameter mud hammers with 8 1/2 inch hammer bits. A Novatek MHN5 and an SDS Digger FH185 mud hammer were tested with several bit types, with performance being compared to a conventional (IADC Code 537) tricone bit. These tools functionally operated in all of the simulated downhole environments. The performance was in the range of the baseline ticone or better at lower borehole pressures, but at higher borehole pressures the performance was in the lower range or below that of the baseline tricone bit. A new drilling mode was observed, while operating the MHN5 mud hammer. This mode was noticed as the weight on bit (WOB) was in transition from low to high applied load. During this new ''transition drilling mode'', performance was substantially improved and in some cases outperformed the tricone bit. Improvements were noted for the SDS tool while drilling with a more aggressive bit design. Future work includes the optimization of these or the next generation tools for operating in higher density and higher borehole pressure conditions and improving bit design and technology based on the knowledge gained from this test program.« less

Investigating Created Properties of Nanoparticles Based Drilling Mud

NASA Astrophysics Data System (ADS)

Ghasemi, Nahid; Mirzaee, Mojtaba; Aghayari, Reza; Maddah, Heydar

2018-05-01

The success of drilling operations is heavily dependent on the drilling fluid. Drilling fluids cool down and lubricate the drill bit, remove cuttings, prevent formation damage, suspend cuttings and also cake off the permeable formation, thus retarding the passage of fluid into the formation. Typical micro or macro sized loss circulation materials (LCM) show limited success, especially in formations dominated by micropores, due to their relatively large sizes. Due to unique characteristics of nanoparticles such as their size and high surface area to volume ratio, they play an effective role in solving problems associated with the drilling fluid. In this study, we investigate the effect of adding Al2O3 and TiO2 nanoparticles into the drilling mud. Al2O3 and TiO2 nanoparticles were used in 20 and 60 nm of size and 0.05 wt% in concentration. Investigating the effects of temperature and pressure has shown that an increase in temperature can reduce the drilling mud rheological properties such as plastic viscosity, while an increase in pressure can enhance these properties. Also, the effects of pressure in high temperatures were less than those in low temperatures. Studying the effects of adding nanoparticles has shown that they can reduce the drilling mud rheological properties. Moreover, they can increase gel strength, reduce capillary suction time and decrease formation damage.

Investigation of mud density and weighting materials effect on drilling fluid filter cake properties and formation damage

NASA Astrophysics Data System (ADS)

Fattah, K. A.; Lashin, A.

2016-05-01

Drilling fluid density/type is an important factor in drilling and production operations. Most of encountered problems during rotary drilling are related to drilling mud types and weights. This paper aims to investigate the effect of mud weight on filter cake properties and formation damage through two experimental approaches. In the first approach, seven water-based drilling fluid samples with same composition are prepared with different densities (9.0-12.0 lb/gal) and examined to select the optimum mud weight that has less damage. The second approach deals with investigating the possible effect of the different weighting materials (BaSO4 and CaCO3) on filter cake properties. High pressure/high temperature loss tests and Scanning Electron Microscopy (SEM) analyses were carried out on the filter cake (two selected samples). Data analysis has revealed that mud weigh of 9.5 lb/gal has the less reduction in permeability of ceramic disk, among the seven used mud densities. Above 10.5 ppg the effect of the mud weight density on formation damage is stabilized at constant value. Fluids of CaCO3-based weighting material, has less reduction in the porosity (9.14%) and permeability (25%) of the filter disk properties than the BaSO4-based fluid. The produced filter cake porosity increases (from 0.735 to 0.859) with decreasing of fluid density in case of drilling samples of different densities. The filtration loss tests indicated that CaCO3 filter cake porosity (0.52) is less than that of the BaSO4 weighted material (0.814). The thickness of the filter cake of the BaSO4-based fluid is large and can cause some problems. The SEM analysis shows that some major elements do occur on the tested samples (Ca, Al, Si, and Ba), with dominance of Ca on the expense of Ba for the CaCO3 fluid sample and vice versa. The less effect of 9.5 lb/gal mud sample is reflected in the well-produced inter-particle pore structure and relatively crystal size. A general recommendation is given to minimize the future utilization of Barium Sulfate as a drilling fluid.

Interpretation of a leak-off test conducted near the bottom of the Kumano Forearc Basin strata at IODP Site C0002 in the Nankai accretionary complex, SW Japan

NASA Astrophysics Data System (ADS)

Song, I.; Huepers, A.; Olcott, K. A.; Saffer, D. M.; Dugan, B.; Strasser, M.

2013-12-01

The Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) is a long-term, multi-stage scientific drilling project launched for investigating fault mechanics and seismogenesis along subduction megathrusts. One main key to the mechanics of the plate boundary is understanding the absolute mechanical strength and the in situ stress along the megathrust. As part of efforts to access the Nankai Trough seismogenic zone, the NanTroSEIZE Integrated Ocean Drilling Program (IODP) project began riser-based drilling operations at Site C0002 (Hole C0002F) in 2010 during IODP Expedition 326, with the objective of reaching the plate interface at ~6800 meters below the seafloor (mbsf). The geology in this area is composed of the Kumano Forearc Basin sedimentary strata to ~940 mbsf, underlain by the inner accretionary wedge. IODP Expedition 326 drilled Hole C0002F to 872.5 mbsf, near the bottom of the Kumano Basin, and set a 20-inch casing string to 860.2 mbsf. During IODP Expedition 338 in 2012, the hole was extended to 2005.5 mbsf. At the beginning of the operation, a leak-off test (LOT) was conducted in the interval of 872.5-875.5 mbsf, to define the maximum mud weight for the next stage of logging-while-drilling (LWD). Drilling-out-cement (DOC) at the bottom of the hole prior to the LOT provided a 3-m long, 17-inch diameter open borehole for the LOT. For the LOT, this open hole interval was pressurized with the outer annulus closed by the blow out preventer (BOP) using drilling mud of density of 1100 kg/m3, and mud pressure was measured at the cement pumps. The bottom-hole pressure was calculated by the recorded pressure plus the static pressure of the mud column. The first cycle of pressurization was conducted with injection of drilling mud at 31.8 l/min. However, the leak-off pressure (LOP) was not clearly defined because a large volume of mud was lost. Therefore a second cycle was conducted with a higher drilling mud injection rate (47.7 l /min). The rapid increase in pressure with a lower volume of mud injected during the second cycle suggests that a good mud cake was formed around the borehole wall, possibly due to mud flowing into the formation during the first cycle. In the second cycle, we identify a LOP of ~32.0 MPa from the pressure-volume record, which we interpret as the least principal stress. The total vertical stress given by the integration of bulk density with respect to depth is 35.7 MPa, indicating that the LOP reflects the least horizontal stress. This result can be a solid basis to constrain the in situ state of stress from indirect stress indicators such as wellbore failures at other depths.

Real-time drilling mud gas monitoring for qualitative evaluation of hydrocarbon gas composition during deep sea drilling in the Nankai Trough Kumano Basin.

PubMed

Hammerschmidt, Sebastian B; Wiersberg, Thomas; Heuer, Verena B; Wendt, Jenny; Erzinger, Jörg; Kopf, Achim

2014-01-01

Integrated Ocean Drilling Program Expedition 338 was the second scientific expedition with D/V Chikyu during which riser drilling was conducted as part of the Nankai Trough Seismogenic Zone Experiment. Riser drilling enabled sampling and real-time monitoring of drilling mud gas with an onboard scientific drilling mud gas monitoring system ("SciGas"). A second, independent system was provided by Geoservices, a commercial mud logging service. Both systems allowed the determination of (non-) hydrocarbon gas, while the SciGas system also monitored the methane carbon isotope ratio (δ(13)CCH4). The hydrocarbon gas composition was predominated by methane (> 1%), while ethane and propane were up to two orders of magnitude lower. δ(13)CCH4 values suggested an onset of thermogenic gas not earlier than 1600 meter below seafloor. This study aims on evaluating the onboard data and subsequent geological interpretations by conducting shorebased analyses of drilling mud gas samples. During shipboard monitoring of drilling mud gas the SciGas and Geoservices systems recorded up to 8.64% and 16.4% methane, respectively. Ethane and propane concentrations reached up to 0.03 and 0.013%, respectively, in the SciGas system, but 0.09% and 0.23% in the Geoservices data. Shorebased analyses of discrete samples by gas chromatography showed a gas composition with ~0.01 to 1.04% methane, 2 - 18 ppmv ethane, and 2 - 4 ppmv propane. Quadruple mass spectrometry yielded similar results for methane (0.04 to 4.98%). With δD values between -171‰ and -164‰, the stable hydrogen isotopic composition of methane showed little downhole variability. Although the two independent mud gas monitoring systems and shorebased analysis of discrete gas sample yielded different absolute concentrations they all agree well with respect to downhole variations of hydrocarbon gases. The data point to predominantly biogenic methane sources but suggest some contribution from thermogenic sources at depth, probably due to mixing. In situ thermogenic gas production at depths shallower 2000 mbsf is unlikely based on in situ temperature estimations between 81°C and 85°C and a cumulative time-temperature index of 0.23. In conclusion, the onboard SciGas data acquisition helps to provide a preliminary, qualitative evaluation of the gas composition, the in situ temperature and the possibility of gas migration.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnis Judzis

2002-10-01

This document details the progress to date on the OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE -- A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING contract for the quarter starting July 2002 through September 2002. Even though we are awaiting the optimization portion of the testing program, accomplishments include the following: (1) Smith International agreed to participate in the DOE Mud Hammer program. (2) Smith International chromed collars for upcoming benchmark tests at TerraTek, now scheduled for 4Q 2002. (3) ConocoPhillips had a field trial of the Smith fluid hammer offshore Vietnam. The hammer functioned properly, though themore » well encountered hole conditions and reaming problems. ConocoPhillips plan another field trial as a result. (4) DOE/NETL extended the contract for the fluid hammer program to allow Novatek to ''optimize'' their much delayed tool to 2003 and to allow Smith International to add ''benchmarking'' tests in light of SDS Digger Tools' current financial inability to participate. (5) ConocoPhillips joined the Industry Advisors for the mud hammer program. (6) TerraTek acknowledges Smith International, BP America, PDVSA, and ConocoPhillips for cost-sharing the Smith benchmarking tests allowing extension of the contract to complete the optimizations.« less

Occupational exposure to airborne contaminants during offshore oil drilling.

PubMed

Kirkhus, Niels E; Thomassen, Yngvar; Ulvestad, Bente; Woldbæk, Torill; Ellingsen, Dag G

2015-07-01

The aim was to study exposure to airborne contaminants in oil drillers during ordinary work. Personal samples were collected among 65 drill floor workers on four stationary and six moveable rigs in the Norwegian offshore sector. Air concentrations of drilling mud were determined based on measurements of the non-volatile mud components Ca and Fe. The median air concentration of mud was 140 μg m(-3). Median air concentrations of oil mist (180 μg m(-3)), oil vapour (14 mg m(-3)) and organic carbon (46 μg m(-3)) were also measured. All contaminants were detected in all work areas (drill floor, shaker area, mud pits, pump room, other areas). The highest air concentrations were measured in the shaker area, but the differences in air concentrations between working areas were moderate. Oil mist and oil vapour concentrations were statistically higher on moveable rigs than on stationary rigs, but after adjusting for differences in mud temperature the differences between rig types were no longer of statistical significance. Statistically significant positive associations were found between mud temperature and the concentrations of oil mist (Spearman's R = 0.46) and oil vapour (0.39), and between viscosity of base oil and oil mist concentrations. Use of pressure washers was associated with higher air concentrations of mud. A series of 18 parallel stationary samples showed a high and statistically significant association between concentrations of organic carbon and oil mist (r = 0.98). This study shows that workers are exposed to airborne non-volatilized mud components. Air concentrations of volatile mud components like oil mist and oil vapour were low, but were present in all the studied working areas.

The first microbiological contamination assessment by deep-sea drilling and coring by the D/V Chikyu at the Iheya North hydrothermal field in the Mid-Okinawa Trough (IODP Expedition 331)

PubMed Central

Yanagawa, Katsunori; Nunoura, Takuro; McAllister, Sean M.; Hirai, Miho; Breuker, Anja; Brandt, Leah; House, Christopher H.; Moyer, Craig L.; Birrien, Jean-Louis; Aoike, Kan; Sunamura, Michinari; Urabe, Tetsuro; Mottl, Michael J.; Takai, Ken

2013-01-01

During the Integrated Ocean Drilling Program (IODP) Expedition 331 at the Iheya North hydrothermal system in the Mid-Okinawa Trough by the D/V Chikyu, we conducted microbiological contamination tests of the drilling and coring operations. The contamination from the drilling mud fluids was assessed using both perfluorocarbon tracers (PFT) and fluorescent microsphere beads. PFT infiltration was detected from the periphery of almost all whole round cores (WRCs). By contrast, fluorescent microspheres were not detected in hydrothermally active core samples, possibly due to thermal decomposition of the microspheres under high-temperature conditions. Microbial contamination from drilling mud fluids to the core interior subsamples was further characterized by molecular-based evaluation. The microbial 16S rRNA gene phylotype compositions in the drilling mud fluids were mainly composed of sequences of Beta- and Gammaproteobacteria, and Bacteroidetes and not archaeal sequences. The phylotypes that displayed more than 97% similarity to the sequences obtained from the drilling mud fluids were defined as possible contaminants in this study and were detected as minor components of the bacterial phylotype compositions in 13 of 37 core samples. The degree of microbiological contamination was consistent with that determined by the PFT and/or microsphere assessments. This study suggests a constructive approach for evaluation and eliminating microbial contamination during riser-less drilling and coring operations by the D/V Chikyu. PMID:24265628

The first microbiological contamination assessment by deep-sea drilling and coring by the D/V Chikyu at the Iheya North hydrothermal field in the Mid-Okinawa Trough (IODP Expedition 331).

PubMed

Yanagawa, Katsunori; Nunoura, Takuro; McAllister, Sean M; Hirai, Miho; Breuker, Anja; Brandt, Leah; House, Christopher H; Moyer, Craig L; Birrien, Jean-Louis; Aoike, Kan; Sunamura, Michinari; Urabe, Tetsuro; Mottl, Michael J; Takai, Ken

2013-01-01

During the Integrated Ocean Drilling Program (IODP) Expedition 331 at the Iheya North hydrothermal system in the Mid-Okinawa Trough by the D/V Chikyu, we conducted microbiological contamination tests of the drilling and coring operations. The contamination from the drilling mud fluids was assessed using both perfluorocarbon tracers (PFT) and fluorescent microsphere beads. PFT infiltration was detected from the periphery of almost all whole round cores (WRCs). By contrast, fluorescent microspheres were not detected in hydrothermally active core samples, possibly due to thermal decomposition of the microspheres under high-temperature conditions. Microbial contamination from drilling mud fluids to the core interior subsamples was further characterized by molecular-based evaluation. The microbial 16S rRNA gene phylotype compositions in the drilling mud fluids were mainly composed of sequences of Beta- and Gammaproteobacteria, and Bacteroidetes and not archaeal sequences. The phylotypes that displayed more than 97% similarity to the sequences obtained from the drilling mud fluids were defined as possible contaminants in this study and were detected as minor components of the bacterial phylotype compositions in 13 of 37 core samples. The degree of microbiological contamination was consistent with that determined by the PFT and/or microsphere assessments. This study suggests a constructive approach for evaluation and eliminating microbial contamination during riser-less drilling and coring operations by the D/V Chikyu.

Test drilling in basalts, Lalamilo area, South Kohala District, Hawaii

USGS Publications Warehouse

Teasdale, Warren E.

1980-01-01

Test drilling has determined that a downhole-percussion airhammer can be used effectively to drill basalts in Hawaii. When used in conjunction with a foam-type drilling fluid, the hammer-bit penetration rate was rapid. Continuous drill cuttings from the materials penetrated were obtained throughout the borehole except from extremely fractured or weathered basalt zones where circulation was lost or limited. Cementing of these zones as soon as encountered reduced problems of stuck tools, washouts, and loss of drill-cuttings. Supplies and logistics on the Hawaiian Islands, always a major concern, require that all anticipated drilling supplies, spare rig and tool parts, drilling muds and additives, foam, and miscellaneous hardware be on hand before starting to drill. If not, the resulting rig downtime is costly in both time and money. (USGS)

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnis Judzis

2003-01-01

This document details the progress to date on the ''OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE -- A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING'' contract for the quarter starting October 2002 through December 2002. Even though we are awaiting the optimization portion of the testing program, accomplishments included the following: (1) Smith International participated in the DOE Mud Hammer program through full scale benchmarking testing during the week of 4 November 2003. (2) TerraTek acknowledges Smith International, BP America, PDVSA, and ConocoPhillips for cost-sharing the Smith benchmarking tests allowing extension of the contract to add to themore » benchmarking testing program. (3) Following the benchmark testing of the Smith International hammer, representatives from DOE/NETL, TerraTek, Smith International and PDVSA met at TerraTek in Salt Lake City to review observations, performance and views on the optimization step for 2003. (4) The December 2002 issue of Journal of Petroleum Technology (Society of Petroleum Engineers) highlighted the DOE fluid hammer testing program and reviewed last years paper on the benchmark performance of the SDS Digger and Novatek hammers. (5) TerraTek's Sid Green presented a technical review for DOE/NETL personnel in Morgantown on ''Impact Rock Breakage'' and its importance on improving fluid hammer performance. Much discussion has taken place on the issues surrounding mud hammer performance at depth conditions.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, D.B.

This paper reports on experiments to examine gas migration rates in drilling muds that were performed in a 15-m-long, 200-mm-ID inclinable flow loop where air injection simulates gas entry during a kick. These tests were conducted using a xanthum gum (a common polymer used in drilling fluids) solution to simulate drilling muds as the liquid phase and air as the gas phase. This work represents a significant extension of existing correlations for gas/liquid flows in large pipe diameters with non- Newtonian fluids. Bubbles rise faster in drilling muds than in water despite the increased viscosity. This surprising result is causedmore » by the change in the flow regime, with large slug-type bubbles forming at lower void fractions. The gas velocity is independent of void fraction, thus simplifying flow modeling. Results show that a gas influx will rise faster in a well than previously believed. This has major implications for kick simulation, with gas arriving at the surface earlier than would be expected and the gas outflow rate being higher than would have been predicted. A model of the two-phase gas flow in drilling mud, including the results of this work, has been incorporated into the joint Schlumberger Cambridge Research (SCR)/BP Intl. kick model.« less

Demulsification. [branched polyalkylene polyamines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickson, W.J.; Jenkins, F.W.

1966-07-05

A method of demulsification uses branched polyalkylene polyamines or their derivatives as demulsifiers for water-in-oil and oil-in-water emulsions. In addition to demulsification these products have a broad spectrum of uses. Among other uses are the following: (1) as corrosion inhibitors; (2) as fuel oil or lubricating oil additives; (3) as scale preventatives; (4) as acidizing additives; (5) as water-treating agents in waterflooding operations; (6) as mud additives; (7) as agents for the removal of mud filter cake from the walls of newly drilled wells; (8) as agents in paraffin solvents; (9) as additives in fracturing fluids; and (10) as agentsmore » in bactericides and fungicides. (8 claims)« less

Contamination assessment in microbiological sampling of the Eyreville core, Chesapeake Bay impact structure

USGS Publications Warehouse

Gronstal, A.L.; Voytek, M.A.; Kirshtein, J.D.; Von der, Heyde; Lowit, M.D.; Cockell, C.S.

2009-01-01

Knowledge of the deep subsurface biosphere is limited due to difficulties in recovering materials. Deep drilling projects provide access to the subsurface; however, contamination introduced during drilling poses a major obstacle in obtaining clean samples. To monitor contamination during the 2005 International Continental Scientific Drilling Program (ICDP)-U.S. Geological Survey (USGS) deep drilling of the Chesapeake Bay impact structure, four methods were utilized. Fluorescent microspheres were used to mimic the ability of contaminant cells to enter samples through fractures in the core material during retrieval. Drilling mud was infused with a chemical tracer (Halon 1211) in order to monitor penetration of mud into cores. Pore water from samples was examined using excitation-emission matrix (EEM) fl uorescence spectroscopy to characterize dissolved organic carbon (DOC) present at various depths. DOC signatures at depth were compared to signatures from drilling mud in order to identify potential contamination. Finally, microbial contaminants present in drilling mud were identified through 16S ribosomal deoxyribonucleic acid (rDNA) clone libraries and compared to species cultured from core samples. Together, these methods allowed us to categorize the recovered core samples according to the likelihood of contamination. Twenty-two of the 47 subcores that were retrieved were free of contamination by all the methods used and were subsequently used for microbiological culture and culture-independent analysis. Our approach provides a comprehensive assessment of both particulate and dissolved contaminants that could be applied to any environment with low biomass. ?? 2009 The Geological Society of America.

Hard-rock jetting. Part 2. Rock type decides jetting economics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pols, A.C.

1977-02-07

In Part 2, Koninklijke Shell Exploratie en Produktie Laboratorium presents the results of jet-drilling laminated formations. Shell concludes that (1) hard, laminated rock cannot be jet-drilled satisfactorily without additional mechanical cutting aids, (2) the increase in penetration rate with bit-pressure drop is much lower for impermeable rock than it is for permeable rock, (3) drilling mud can have either a positive or a negative effect on penetration rate in comparison with water, depending on the material drilled, and (4) hard, isotropic, sedimentary, impermeable rock can be drilled using jets at higher rates than with conventional means. However, jetting becomes profitablemore » only in the case of expensive rigs.« less

Turbodrills and innovative PDC bits economically drilled hard formations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boudreaux, R.C.; Massey, K.

1994-03-28

The use of turbodrills and polycrystalline diamond compact (PDC) bits with an innovative, tracking cutting structure has improved drilling economics in medium and hard formations in the Gulf of Mexico. Field results have confirmed that turbodrilling with trackset PDC bits reduced drilling costs, compared to offset wells. The combination of turbodrills and trackset bits has been used successfully in a broad range of applications and with various drilling parameters. Formations ranging from medium shales to hard, abrasive sands have been successfully and economically drilled. The tools have been used in both water-based and oil-based muds. Additionally, the turbo-drill and tracksetmore » PDC bit combination has been stable on directional drilling applications. The locking effect of the cutting structure helps keep the bit on course.« less

Assessment of two thermally treated drill mud wastes for landfill containment applications.

PubMed

Carignan, Marie-Pierre; Lake, Craig B; Menzies, Todd

2007-10-01

Offshore oil and gas drilling operations generate significant amounts of drill mud waste, some of which is transported onshore for subsequent thermal treatment (i.e. via thermal remediation). This treatment process results in a mineral waste by-product (referred to as thermally treated drill mud waste; TTDMW). Bentonites are originally present in many of the drill mud products and it is hypothesized that TTDMW can be utilized in landfill containment applications (i.e. cover or base liner). The objective of this paper is to examine the feasibility of this application by performing various physical and chemical tests on two TTDMW samples. It is shown that the two TTDMW samples contained relatively small amounts of clay-sized minerals although hydraulic conductivity values are found to be less than 10(-8) m/s. Organic carbon contents of the samples were approximately 2%. Mineralogy characterization of the samples confirmed varying amounts of smectite, however, peak friction angles for a TTDMW sample was greater than 36 degrees. Chemical characterization of the TTDMW samples show potential leaching of barium and small amounts of other heavy metals. Discussion is provided in the paper on suggestions to assist in overcoming regulatory issues associated with utilization of TTDMW in landfill containment applications.

Seismic attributes and advanced computer algorithm to predict formation pore pressure: Qalibah formation of Northwest Saudi Arabia

NASA Astrophysics Data System (ADS)

Nour, Abdoulshakour M.

Oil and gas exploration professionals have long recognized the importance of predicting pore pressure before drilling wells. Pre-drill pore pressure estimation not only helps with drilling wells safely but also aids in the determination of formation fluids migration and seal integrity. With respect to the hydrocarbon reservoirs, the appropriate drilling mud weight is directly related to the estimated pore pressure in the formation. If the mud weight is lower than the formation pressure, a blowout may occur, and conversely, if it is higher than the formation pressure, the formation may suffer irreparable damage due to the invasion of drilling fluids into the formation. A simple definition of pore pressure is the pressure of the pore fluids in excess of the hydrostatic pressure. In this thesis, I investigated the utility of advance computer algorithm called Support Vector Machine (SVM) to learn the pattern of high pore pressure regime, using seismic attributes such as Instantaneous phase, t*Attenuation, Cosine of Phase, Vp/Vs ratio, P-Impedance, Reflection Acoustic Impedance, Dominant frequency and one well attribute (Mud-Weigh) as the learning dataset. I applied this technique to the over pressured Qalibah formation of Northwest Saudi Arabia. The results of my research revealed that in the Qalibah formation of Northwest Saudi Arabia, the pore pressure trend can be predicted using SVM with seismic and well attributes as the learning dataset. I was able to show the pore pressure trend at any given point within the geographical extent of the 3D seismic data from which the seismic attributes were derived. In addition, my results surprisingly showed the subtle variation of pressure within the thick succession of shale units of the Qalibah formation.

Investigation of melamine derived quaternary as ammonium salt potential shale inhibitor

NASA Astrophysics Data System (ADS)

Yu, Hongjiang; Hu, Weimin; Guo, Gang; Huang, Lei; Li, Lili; Gu, Xuefan; Zhang, Zhifang; Zhang, Jie; Chen, Gang

2017-06-01

Melamine, sodium chloroacetate and sodium hydroxide were used as raw materials to synthesize a kind of neutral quaternary ammonium salt (NQAS) as potential clay swelling inhibitor and water-based drilling fluid additive, and the reaction conditions were screened based on the linear expansion rate of bentonite. The inhibitive properties of NQASs were investigated by various methods, including montmorillonite (MMT) linear expansion test, mud ball immersing test, particle distribution measurement, thermogravimetric analysis and scanning electron microscopy etc. The results indicate that NQAS can inhibit expansion and dispersion of clay in water effectively. At the same condition, the bentonite linear expansion rate in NQAS-6 solution is much lower than those of others, and the hydration expansion degree of the mud ball in 0.5% NQAS-6 solution is appreciably weaker than the control test. The compatibility test indicates NQAS-6 could be compatible with the conventional additives in water-based drilling fluids, and the temperature resistance of modified starch was improved effectively. Meanwhile, the inhibitive mechanism was discussed through the particle distribution measurement.

Offshore wellbore stability analysis based on fully coupled poro-thermo-elastic theory

NASA Astrophysics Data System (ADS)

Cao, Wenke; Deng, Jingen; Yu, Baohua; Liu, Wei; Tan, Qiang

2017-03-01

Drilling-induced tensile fractures are usually caused when the weight of mud is too high, and the effective tangential stress becomes tensile. It is thus hard to explain why tensile fractures are distributed along the lower part of a hole in an offshore exploration well when the mud weight is low. According to analysis, the reason could be the thermal effect, which cannot be ignored because of the drilling fluid and the cooling action of sea water during circulation. A heat transfer model is set up to obtain the temperature distribution of the wellbore and its formation by the finite difference method. Then, fully coupled poro-thermo-elastic theory is used to study the pore pressure and effective stress around the wellbore. By comparing it with both poroelastic and elastic models, it is indicated that the poroelastic effect is dominant at the beginning of circulation and inhibits tensile fractures from forming; then, the thermal effect becomes more important and decreases the effective tangential stress with the passing of time, so the drilling fluid and the cooling effect of sea water can cause tensile fractures to happen. Meanwhile, tensile fractures are shallow and not likely to lead to mud leakage with lower mud weight, which agrees with the actual drilling process. On the other hand, the fluid cooling effect could increase the strength of the rock and reduce the likelihood of shear failure, which would be beneficial for wellbore stability. So, the thermal effect cannot be neglected in offshore wellbore stability analysis, and mud weight and borehole exposure time should be controlled in the case of mud loss.

Real Time Mud Gas Logging During Drilling of DFDP-2B

NASA Astrophysics Data System (ADS)

Mathewson, L. A.; Toy, V.; Menzies, C. D.; Zimmer, M.; Erzinger, J.; Niedermann, S.; Cox, S.

2015-12-01

The Deep Fault Drilling Project (DFDP) aims to improve our understanding of the Alpine Fault Zone, a tectonically active mature fault system in New Zealand known to rupture in large events, by deep scientific drilling. The borehole DFDP-2B approached the Alpine Fault at depth, reaching a final depth of 892 m (820 m true vertical depth). Online gas analysis (OLGA) while drilling tracked changes in the composition of gases extracted from the circulating drill mud. The composition of fluids from fault zones can provide information about their origins, flow rates and -paths, fluid-rock interactions along these paths, and the permeability structure of the faulted rock mass. Apart from an atmospheric input, the gases in drilling mud derive from the pore space of rock, crushed at the drill bit, and from permeable layers intersected by the borehole. The rapid formation of mud wall cake seals the borehole from further fluid inflow, hence formation-derived gases enter mostly at the depth of the drill bit. OLGA analyses N2, O2, Ar, CO2, CH4, He, and H2 on a mass spectrometer, hydrocarbons CH4, C2H6, C3H8, i-C4H10, and n-C4H10 on a gas chromatograph, and Rn using a lucas-cell detector. Gas was sampled for offline analyses on noble gas and stable isotopes to complement the OLGA dataset. The principle formation-derived gases found in drilling mud during drilling of DFDP-2 were CO2 and CH4, with smaller component of H2 and He2. High radon activity is interpreted to reflect intervals of active fluid flow through highly fractured and faulted rock. 3He/4He values in many samples were extremely air-contaminated, i.e. there was almost no excess of non-atmospheric He. The 3He/4He values measured at 236 m and 610 m, which are the only analyses with uncertainties <100%, are very similar to those measured in hot springs along the Alpine Fault, e.g. Fox River (0.64 Ra), Copland (0.42 Ra), Lower Wanganui (0.81 Ra). We will compare these data to those gathered using OLGA and discuss the implications.

A composite lithology log while drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tannenbaum, E.; Sutcliffe, B.; Franks, A.

A new method for producing a computerized composite lithology log (CLL) while drilling by integrating MWD (measurement while drilling) and surface data is described. At present, lithology logs are produced at the well site by mud loggers. They provide basic description and relative amounts of lithologies. Major difficulties are encountered in relating the cuttings to their original formations due to mixing in the drilling mud while transporting to the surface, sloughing shales, flawed sampling, etc. This results in a poor control on the stratigraphic sequence and on the depth of formation boundaries. A composite log can be produced after drillingmore » this additional inputs such as wireline, petrography, and paleontology. This process is labor intensive and expensive. The CLL integrates three types of data (MWD mechanical, MWD geophysical, and surface cuttings) acquired during drilling, in three time stages: (1) Real Time. MWD drilling mechanical data including the rate of penetration and the downhole torque. This stage would provide bed boundaries and some inferred lithology. This would assist the driller with immediate drilling decisions and determine formation tops for coring, casing point, and correlation. (2) MWD Time. Recomputation of the above by adding MWD geophysical data (gamma-ray, resistivity, neutron-density). This stage would upgrade the lithology inference, and give higher resolution to bed boundaries, (3) Lag Time. Detailed analysis of surface cuttings to confirm the inferred lithologies. This last input results in a high-quality CLL with accurate lithologies and bed boundaries.« less

The acute and chronic effects of wastes associated with offshore oil and gas production on temperate and tropical marine ecological processes.

PubMed

Holdway, Douglas A

2002-03-01

A review of the acute and chronic effects of produced formation water (PFW), drilling fluids (muds) including oil-based cutting muds, water-based cutting muds, ester-based cutting muds and chemical additives, and crude oils associated with offshore oil and gas production was undertaken in relation to both temperate and tropical marine ecological processes. The main environmental effects are summarized, often in tabular form. Generally, the temporal and spatial scales of these studies, along with the large levels of inherent variation in natural environments, have precluded our ability to predict the potential long-term environmental impacts of the offshore oil and gas production industry. A series of critical questions regarding the environmental effects of the offshore oil and gas production industry that still remain unanswered are provided for future consideration.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnis Judzis

2003-07-01

This document details the progress to date on the ''OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE--A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING'' contract for the quarter starting April 2003 through June 2003. The DOE and TerraTek continue to wait for Novatek on the optimization portion of the testing program (they are completely rebuilding their fluid hammer). Accomplishments included the following: (1) Hughes Christensen has recently expressed interest in the possibility of a program to examine cutter impact testing, which would be useful in a better understanding of the physics of rock impact. Their interest however is notmore » necessarily fluid hammers, but to use the information for drilling bit development. (2) Novatek (cost sharing supplier of tools) has informed the DOE project manager that their tool may not be ready for ''optimization'' testing late summer 2003 (August-September timeframe) as originally anticipated. During 3Q Novatek plans to meet with TerraTek to discuss progress with their tool for 4Q 2003 testing. (3) A task for an addendum to the hammer project related to cutter impact studies was written during 2Q 2003. (4) Smith International internally is upgrading their hammer for the optimization testing phase. One currently known area of improvement is their development program to significantly increase the hammer blow energy.« less

Drilling fluids: Where should research dollars be spent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sauber

This article discusses the question of where to apply research dollars in the field of drilling fluids which is gravely impacted by environmental concerns. In fact, environmental regulations are the driving force in determining the thrust of drilling fluids research. For example, use of oil-base fluids offshore have, for all practical purposes, been precluded by high disposal costs since offshore disposal has been prohibited. Consequently it must be determined if a water-base mud can be developed that has all or most of the advantages of an oil-base mud.

Toxicity assessment of individual ingredients of synthetic-based drilling muds (SBMs).

PubMed

Bakhtyar, Sajida; Gagnon, Marthe Monique

2012-09-01

Synthetic-based drilling muds (SBMs) offer excellent technical characteristics while providing improved environmental performance over other drilling muds. The low acute toxicity and high biodegradability of SBMs suggest their discharge at sea would cause minimal impacts on marine ecosystems, however, chronic toxicity testing has demonstrated adverse effects of SBMs on fish health. Sparse environmental monitoring data indicate effects of SBMs on bottom invertebrates. However, no environmental toxicity assessment has been performed on fish attracted to the cutting piles. SBM formulations are mostly composed of synthetic base oils, weighting agents, and drilling additives such as emulsifiers, fluid loss agents, wetting agents, and brine. The present study aimed to evaluate the impact of exposure to individual ingredients of SBMs on fish health. To do so, a suite of biomarkers [ethoxyresorufin-O-deethylase (EROD) activity, biliary metabolites, sorbitol dehydrogenase (SDH) activity, DNA damage, and heat shock protein] have been measured in pink snapper (Pagrus auratus) exposed for 21 days to individual ingredients of SBMs. The primary emulsifier (Emul S50) followed by the fluid loss agent (LSL 50) caused the strongest biochemical responses in fish. The synthetic base oil (Rheosyn) caused the least response in juvenile fish. The results suggest that the impact of Syndrill 80:20 on fish health might be reduced by replacement of the primary emulsifier Emul S50 with an alternative ingredient of less toxicity to aquatic biota. The research provides a basis for improving the environmental performance of SBMs by reducing the environmental risk of their discharge and providing environmental managers with information regarding the potential toxicity of individual ingredients.

Exposure to oil mist and oil vapour during offshore drilling in norway, 1979-2004.

PubMed

Steinsvåg, Kjersti; Bråtveit, Magne; Moen, Bente E

2006-03-01

To describe personal exposure to airborne hydrocarbon contaminants (oil mist and oil vapour) from 1979 to 2004 in the mud-handling areas of offshore drilling facilities operating on the Norwegian continental shelf when drilling with oil-based muds. Qualitative and quantitative information was gathered during visits to companies involved in offshore oil and gas production in Norway. Monitoring reports on oil mist and oil vapour exposure covered 37 drilling facilities. Exposure data were analysed using descriptive statistics and by constructing linear mixed-effects models. Samples had been taken during the use of three generations of hydrocarbon base oils, namely diesel oils (1979-1984), low-aromatic mineral oils (1985-1997) and non-aromatic mineral oils (1998-2004). Sampling done before 1984 showed high exposure to diesel vapour (arithmetic mean, AM = 1217 mg m(-3)). When low-aromatic mineral oils were used, the exposure to oil mist and oil vapour was 4.3 and 36 mg m(-3), and the respective AMs for non-aromatic mineral oils were reduced to 0.54 and 16 mg m(-3). Downward time trends were indicated for both oil mist (6% per year) and oil vapour (8% per year) when the year of monitoring was introduced as a fixed effect in a linear mixed-effects model analysis. Rig type, technical control measures and mud temperature significantly determined exposure to oil mist. Rig type, type of base oil, viscosity of the base oil, work area, mud temperature and season significantly determined exposure to oil vapour. Major decreases in variability were found for the between-rig components. Exposure to oil mist and oil vapour declined over time in the mud-handling areas of offshore drilling facilities. Exposure levels were associated with rig type, mud temperature, technical control measures, base oil, viscosity of the base oil, work area and season.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE--A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnis Judzis

2004-07-01

This document details the progress to date on the ''OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE--A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING'' contract for the quarter starting April 2004 through June 2004. The DOE and TerraTek continue to wait for Novatek on the optimization portion of the testing program (they are completely rebuilding their fluid hammer). The latest indication is that the Novatek tool would be ready for retesting only 4Q 2004 or later. Smith International's hammer was tested in April of 2004 (2Q 2004 report). Accomplishments included the following: (1) TerraTek re-tested the ''optimized'' fluid hammermore » provided by Smith International during April 2004. Many improvements in mud hammer rates of penetration were noted over Phase 1 benchmark testing from November 2002. (2) Shell Exploration and Production in The Hague was briefed on various drilling performance projects including Task 8 ''Cutter Impact Testing''. Shell interest and willingness to assist in the test matrix as an Industry Advisor is appreciated. (3) TerraTek participated in a DOE/NETL Review meeting at Morgantown on April 15, 2004. The discussions were very helpful and a program related to the Mud Hammer optimization project was noted--Terralog modeling work on percussion tools. (4) Terralog's Dr. Gang Han witnessed some of the full-scale optimization testing of the Smith International hammer in order to familiarize him with downhole tools. TerraTek recommends that modeling first start with single cutters/inserts and progress in complexity. (5) The final equipment problem on the impact testing task was resolved through the acquisition of a high data rate laser based displacement instrument. (6) TerraTek provided Novatek much engineering support for the future re-testing of their optimized tool. Work was conducted on slip ring [electrical] specifications and tool collar sealing in the testing vessel with a reconfigured flow system on Novatek's collar.« less

Treatment of a mud pit by bioremediation.

PubMed

Avdalović, Jelena; Đurić, Aleksandra; Miletić, Srdjan; Ilić, Mila; Milić, Jelena; Vrvić, Miroslav M

2016-08-01

The mud generated from oil and natural gas drilling, presents a considerable ecological problem. There are still insufficient remedies for the removal and minimization of these very stable emulsions. Existing technologies that are in use, more or less successfully, treat about 20% of generated waste drilling mud, while the rest is temporarily deposited in so-called mud pits. This study investigated in situ bioremediation of a mud pit. The bioremediation technology used in this case was based on the use of naturally occurring microorganisms, isolated from the contaminated site, which were capable of using the contaminating substances as nutrients. The bioremediation was stimulated through repeated inoculation with a zymogenous microbial consortium, along with mixing, watering and biostimulation. Application of these bioremediation techniques reduced the concentration of total petroleum hydrocarbons from 32.2 to 1.5 g kg(-1) (95% degradation) during six months of treatment. © The Author(s) 2016.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE--A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnis Judzis

2004-04-01

This document details the progress to date on the OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE--A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING contract for the quarter starting January 2004 through March 2004. The DOE and TerraTek continue to wait for Novatek on the optimization portion of the testing program (they are completely rebuilding their fluid hammer). The latest indication is that the Novatek tool would be ready for retesting only 3Q 2004. Smith International's hammer will be tested in April of 2004 (2Q 2004 report). Accomplishments included the following: (1) TerraTek presented a paper for publication inmore » conjunction with a peer review at the GTI Natural Gas Technologies Conference February 10, 2004. Manuscripts and associated presentation material were delivered on schedule. The paper was entitled ''Mud Hammer Performance Optimization''. (2) Shell Exploration and Production continued to express high interest in the ''cutter impact'' testing program Task 8. Hughes Christensen supplied inserts for this testing program. (3) TerraTek hosted an Industry/DOE planning meeting to finalize a testing program for ''Cutter Impact Testing--Understanding Rock Breakage with Bits'' on February 13, 2004. (4) Formal dialogue with Terralog was initiated. Terralog has recently been awarded a DOE contract to model hammer mechanics with TerraTek as a sub-contractor. (5) Novatek provided the DOE with a schedule to complete their new fluid hammer and test it at TerraTek.« less

Novel Desorber for Online Drilling Mud Gas Logging.

PubMed

Lackowski, Marcin; Tobiszewski, Marek; Namieśnik, Jacek

2016-01-01

This work presents the construction solution and experimental results of a novel desorber for online drilling mud gas logging. The traditional desorbers use mechanical mixing of the liquid to stimulate transfer of hydrocarbons to the gaseous phase that is further analyzed. The presented approach is based on transfer of hydrocarbons from the liquid to the gas bubbles flowing through it and further gas analysis. The desorber was checked for gas logging from four different drilling muds collected from Polish boreholes. The results of optimization studies are also presented in this study. The comparison of the novel desorber with a commercial one reveals strong advantages of the novel one. It is characterized by much better hydrocarbons recovery efficiency and allows reaching lower limits of detection of the whole analytical system. The presented desorber seems to be very attractive alternative over widely used mechanical desorbers.

Independent Technical Investigation of the Puna Geothermal Venture Unplanned Steam Release, June 12 and 13, 1991, Puna, Hawaii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Richard; Whiting, Dick; Moore, James

1991-07-01

On June 24, 1991, a third-party investigation team consisting of Richard P. Thomas, Duey E. Milner, James L. Moore, and Dick Whiting began an investigation into the blowout of well KS-8, which occurred at the Puna Geothermal Venture (PGV) site on June 12, 1991, and caused the unabated release of steam for a period of 31 hours before PGV succeeded in closing in the well. The scope of the investigation was to: (a) determine the cause(s) of the incident; (b) evaluate the adequacy of PGVs drilling and blowout prevention equipment and procedures; and (c) make recommendations for any appropriate changesmore » in equipment and/or procedures. This report finds that the blowout occurred because of inadequacies in PGVs drilling plan and procedures and not as a result of unusual or unmanageable subsurface geologic or hydrologic conditions. While the geothermal resource in the area being drilled is relatively hot, the temperatures are not excessive for modem technology and methods to control. Fluid pressures encountered are also manageable if proper procedures are followed and the appropriate equipment is utilized. A previous blowout of short duration occurred on February 21, 1991, at the KS-7 injection well being drilled by PGV at a depth of approximately 1600'. This unexpected incident alerted PGV to the possibility of encountering a high temperature, fractured zone at a relatively shallow depth. The experience at KS-7 prompted PGV to refine its hydrological model; however, the drilling plan utilized for KS-8 was not changed. Not only did PGV fail to modify its drilling program following the KS-7 blowout, but they also failed to heed numerous ''red flags'' (warning signals) in the five days preceding the KS-8 blowout, which included a continuous 1-inch flow of drilling mud out of the wellbore, gains in mud volume while pulling stands, and gas entries while circulating muds bottoms up, in addition to lost circulation that had occurred earlier below the shoe of the 13-3/8-hch casing.« less

Novel Desorber for Online Drilling Mud Gas Logging

PubMed Central

Lackowski, Marcin; Tobiszewski, Marek; Namieśnik, Jacek

2016-01-01

This work presents the construction solution and experimental results of a novel desorber for online drilling mud gas logging. The traditional desorbers use mechanical mixing of the liquid to stimulate transfer of hydrocarbons to the gaseous phase that is further analyzed. The presented approach is based on transfer of hydrocarbons from the liquid to the gas bubbles flowing through it and further gas analysis. The desorber was checked for gas logging from four different drilling muds collected from Polish boreholes. The results of optimization studies are also presented in this study. The comparison of the novel desorber with a commercial one reveals strong advantages of the novel one. It is characterized by much better hydrocarbons recovery efficiency and allows reaching lower limits of detection of the whole analytical system. The presented desorber seems to be very attractive alternative over widely used mechanical desorbers. PMID:27127674

New mud system produces solids-free, reusable water

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-02-01

The Corpus Christi, Texas, based Cameron Equipment Co., Inc., has developed a closed-loop mud treating system that removes solids from water-based systems and leaves the separated fluid clean and chemical free enough to be re-used directly on the rig. The system has been successfully applied by a Gulf of Mexico operator in areas where zero discharge is required. The alternative mud conditions program offered by the developers is called the Cameron Fluid Recycling System. Designed for closed-loop water-based fluids, the system is a new method of removing solids from normally discharged fluids such as drilling mud, waste and wash water,more » or any other water-based fluid that contains undesirable solids. The patented method efficiently produces end products that are (1) dry solids; and (2) essentially 100% solids-free fluid that can be re-used in the same mud system. All excess drilling mud, and all wash water that would normally go to the reserve pit or a cuttings barge are collected in a tank. Recycled fluid is compatible with the mud system fluid, no harmful chemicals are used, and pH is not altered.« less

POTENTIAL FOR INVASION OF UNDERGROUND SOURCES OF DRINKING WATER THROUGH MUD-PLUGGED WELLS: AN EXPERIMENTAL APPRAISAL

EPA Science Inventory

The main objective of the feasibility study described here was to test the hypothesis that properly plugged wells are effectively sealed by drilling mud. In The process of testing the hypothesis, evidence about dynamics of building mud cake on the wellbore-face was obtained, as ...

A seismic reflection velocity study of a Mississippian mud-mound in the Illinois basin

NASA Astrophysics Data System (ADS)

Ranaweera, Chamila Kumari

Two mud-mounds have been reported in the Ullin limestone near, but not in, the Aden oil field in Hamilton County, Illinois. One mud-mound is in the Broughton oil field of Hamilton County 25 miles to the south of Aden. The second mud-mound is in the Johnsonville oil field in Wayne County 20 miles to the north of Aden. Seismic reflection profiles were shot in 2012 adjacent to the Aden oil field to evaluate the oil prospects and to investigate the possibility of detecting Mississippian mud-mounds near the Aden field. A feature on one of the seismic profiles was interpreted to be a mud-mound or carbonate buildup. A well drilled at the location of this interpreted structure provided digital geophysical logs and geological logs used to refine the interpretation of the seismic profiles. Geological data from the new well at Aden, in the form of drill cuttings, have been used to essentially confirm the existence of a mud-mound in the Ullin limestone at a depth of 4300 feet. Geophysical well logs from the new well near Aden were used to create 1-D computer models and synthetic seismograms for comparison to the seismic data. The reflection seismic method is widely used to aid interpreting subsurface geology. Processing seismic data is an important step in the method as a properly processed seismic section can give a better image of the subsurface geology whereas a poorly processed section could mislead the interpretation. Seismic reflections will be more accurately depicted with careful determination of seismic velocities and by carefully choosing the processing steps and parameters. Various data processing steps have been applied and parameters refined to produce improved stacked seismic records. The resulting seismic records from the Aden field area indicate a seismic response similar to what is expected from a carbonate mud-mound. One-dimensional synthetic seismograms were created using the available sonic and density logs from the well drilled near the Aden seismic lines. The 1-D synthetics were used by Cory Cantrell of Royal Drilling and Producing Company to identify various reflections on the seismic records. Seismic data was compared with the modeled synthetic seismograms to identify what appears to be a carbonate mud-mound within the Aden study area. No mud-mounds have been previously found in the Aden oil field. Average and interval velocities obtained from the geophysical logs from the wells drilled in the Aden area was compared with the same type of well velocities from the Broughton known mud-mound area to observe the significance of velocity variation related to the un-known mud-mound in the Aden study area. The results of the velocity study shows a similar trends in the wells from both areas and are higher at the bottom of the wells. Another approach was used to observe the variation of root mean square velocities calculated from the sonic log from the well velocity from the Aden area and the stacking velocities obtained from the seismic data adjacent to the well.

Means of atmospheric air pollution reduction during drilling wells

NASA Astrophysics Data System (ADS)

Shkitsa, L.; Yatsyshyn, T.; Lyakh, M.; Sydorenko, O.

2016-08-01

The process of drilling oil and gas wells is the source of air pollution through drilling mud evaporation containing hazardous chemical substances. The constructive solution for cleaning device of downhole tool that contains elements covering tube and clean the surface from the mud in the process of rising from the well is offered. Inside the device is filled with magnetic fluid containing the substance neutralizing hazardous substances. The use of the equipment proposed will make it possible to avoid penetration of harmful substances into the environment and to escape the harmful effects of aggressive substances for staff health and increase rig's fire safety.

Borehole instability analysis for IODP Site C0002 of the NanTroSEIZE Project, Nankai Trough subduction zone

NASA Astrophysics Data System (ADS)

Wu, H.; Kido, Y. N.; Kinoshita, M.; Saito, S.

2013-12-01

Wellbore instability is a major challenge for the engineer evaluating borehole and formation conditions. Instability is especially important to understand in areas with high stress variations, significant structure anisotropy, or pre-existing fracture systems. Borehole (in)stability is influenced by rock strength, structural properties, and near-field principal stresses. During drilling, the borehole conditions also impact borehole integrity. Factors that we can measure in the borehole during with logging while drilling (LWD) to understand these conditions include mud weight, mud loss, ROP (Rate of Penetration), RPM (Rotation Per Minute), WOB (Weight on Bit), and TORQ (Power swivel torque value). We conducted borehole instability analysis for Site C0002 of the Nankai Trough transect based on riser and riserless drilling during IODP Expedition 338. The borehole shape, determined from LWD resistivity images, indicates that most of drilling occurred in stable environments, however, in a few instances the bottom hole assembly became stuck. We used our stress profile model to evaluate the mud weight required to drill a stable borehole for the estimated rock strength and physical properties. Based on our analysis, we interpret that borehole instability during IODP Expedition 338 may have been caused by weak bedding plane and fluid overpressure state. Future work with this model will investigate the roles of these conditions.

Stabilization of NaCl-containing cuttings wastes in cement concrete by in situ formed mineral phases.

PubMed

Filippov, Lev; Thomas, Fabien; Filippova, Inna; Yvon, Jacques; Morillon-Jeanmaire, Anne

2009-11-15

Disposal of NaCl-containing cuttings is a major environmental concern due to the high solubility of chlorides. The present work aims at reducing the solubility of chloride by encapsulation in low permeability matrix as well as lowering its solubility by trapping into low-solubility phases. Both the studied materials were cuttings from an oil-based mud in oil drillings containing about 50% of halite, and cuttings in water-based mud from gas drilling containing 90% of halite. A reduction in the amount of dissolved salt from 41 to 19% according to normalized leaching tests was obtained by addition of potassium ortho-phosphate in the mortar formula of oil-based cuttings, while the aluminium dihydrogeno-phosphate is even more efficient for the stabilization of water-based cuttings with a NaCl content of 90%. Addition of ortho-phosphate leads to form a continuous and weakly soluble network in the cement matrix, which reduces the release of salt. The formed mineralogical phases were apatite and hydrocalumite. These phases encapsulate the salt grains within a network, thus lowering its interaction with water or/and trap chloride into low-solubility phases. The tested approaches allow to develop a confinement process of NaCl-containing waste of various compositions that can be applied to wastes, whatever the salt content and the nature of the drilling fluids (water or oil).

Impact of exploratory wells, offshore Florida: A biological assessment

USGS Publications Warehouse

Dustan, Phillip A.; Lidz, Barbara H.; Shinn, Eugene A.

1991-01-01

Seven offshore exploratory oil well sites were examined in an effort to determine the ecological impact of exploratory drilling on the subtropical marine ecosystems of southern Florida, including seagrass beds and coral reefs. The time since drilling ranged from 2 to 29 years; water depths varied between 5 and 70 m. The major long-term ecological impact observed at these sites ranged from the creation of "artificial-reef" conditions to the physical destruction of hardbottom habitat that had not recovered in 29 years. Long-term ecological perturbation appeared to be limited to physical destruction and the deposition of drilling debris, which provided substratum for settling organisms. Significant deposits of drill muds or cuttings were not encountered at any of the sites, and there was no evidence of ecological damage from cuttings or drill muds. The results of this study pertain only to exploratory drilling that, unlike production wells that remain in place for tens of years, is a one-time perturbation to the habitat.

Mechanical Properties of Gas Shale During Drilling Operations

NASA Astrophysics Data System (ADS)

Yan, Chuanliang; Deng, Jingen; Cheng, Yuanfang; Li, Menglai; Feng, Yongcun; Li, Xiaorong

2017-07-01

The mechanical properties of gas shale significantly affect the designs of drilling, completion, and hydraulic fracturing treatments. In this paper, the microstructure characteristics of gas shale from southern China containing up to 45.1% clay were analyzed using a scanning electron microscope. The gas shale samples feature strongly anisotropic characteristics and well-developed bedding planes. Their strength is controlled by the strength of both the matrix and the bedding planes. Conventional triaxial tests and direct shear tests are further used to study the chemical effects of drilling fluids on the strength of shale matrix and bedding planes, respectively. The results show that the drilling fluid has a much larger impact on the strength of the bedding plane than that of the shale matrix. The impact of water-based mud (WBM) is much larger compared with oil-based mud. Furthermore, the borehole collapse pressure of shale gas wells considering the effects of drilling fluids are analyzed. The results show that the collapse pressure increases gradually with the increase of drilling time, especially for WBM.

Effects of the Terra Nova offshore oil development on benthic macro-invertebrates over 10 years of development drilling on the Grand Banks of Newfoundland, Canada

NASA Astrophysics Data System (ADS)

Paine, Michael D.; DeBlois, Elisabeth M.; Kilgour, Bruce W.; Tracy, Ellen; Pocklington, Patricia; Crowley, Roger D.; Williams, Urban P.; Gregory Janes, G.

2014-12-01

This paper describes effects of drilling with water and synthetic-based drilling muds on benthic macro-invertebrates over 10 years at the Terra Nova offshore oil development. As such, the paper provides insight on the effects of relatively new synthetic-based drilling muds (SBMs), and makes an important contribution to our understanding of the long-term chronic effects of drilling on benthic communities. The Terra Nova Field is located approximately 350 km offshore on the Grand Banks of Newfoundland (Canada). Sediment and invertebrate samples were collected in 1997 (baseline) prior to drilling, and subsequently in 2000, 2001, 2002, 2004, 2006, 2008 and 2010. Approximately 50 stations were sampled in each year at distances of less than 1 to approximately 20 km from drill centres. Summary benthic invertebrate community measures examined were total abundance, biomass, richness, diversity and multivariate measures of community composition based on non-Metric Dimensional Scaling (nMDS). Decreases in abundance, biomass and richness were noted at one station located nearest (0.14 km) to a drill centre in some environmental effects monitoring (EEM) years. These decreases coincided with higher levels of tracers of drill muds in sediments (barium and >C10-C21 hydrocarbons). Abundances of selected individual taxa were also examined to help interpret responses when project-related effects on summary measures occurred. Enrichment effects on some tolerant taxa (e.g., the polychaete family Phyllodocidae and the bivalve family Tellinidae) and decreased abundances of sensitive taxa (e.g., the polychaete families Orbiniidae and Paraonidae) were detected to within approximately 1-2 km from discharge source. Lagged responses three to five years after drilling started were noted for Phyllodocidae and Tellinidae, suggesting chronic or indirect effects. Overall, results of benthic community analyses at Terra Nova indicate that effects on summary measures of community composition were spatially limited but, as seen elsewhere, some taxa were more sensitive to drilling discharges.

PAH composition of Water Based Drilling Mud and drill cuttings in the offshore region, east coast of India.

PubMed

Jagwani, Devaanshi; Kulkarni, Atul; Shukla, Parth; Ramteke, Dilip S; Juneja, Harjeet D

2011-11-01

As a consequence of offshore drilling, used Water Based Drilling Muds (WBMs) are typically disposed off, by discharging into the sea; such a disposal does not fully eliminate the environmental hazards. Hence, in this study, 2, 3, 4 and 5 ringed polycyclic aromatic hydrocarbons (PAHs i.e. naphthalene, fluorene, phenanthrene, fluoranthene, chrysene and benzo (a) pyrene) were determined from the WBMs and associated drill cuttings obtained from varying depths(viz. 150, 300 and 600 m) from three offshore wells present in East coast of India. In both WBMs and drill cuttings, concentration of naphthalene was maximum i.e. 81.59 ± 2.73 and 39.87 ± 2.40 mg/kg respectively, while benzo (a) pyrene was minimum i.e. 0.19 ± 0.07 and 0.12 ± 0.03 mg/kg respectively. The WBMs contained significantly (p < 0.05) higher PAH concentration than drill cuttings. The individual PAH concentration significantly (p < 0.01) increased with increasing depth in each well.

Experimental study of improved rheology and lubricity of drilling fluids enhanced with nano-particles

NASA Astrophysics Data System (ADS)

Bég, O. Anwar; Espinoza, D. E. Sanchez; Kadir, Ali; Shamshuddin, MD.; Sohail, Ayesha

2018-04-01

An experimental study of the rheology and lubricity properties of a drilling fluid is reported, motivated by applications in highly deviated and extended reach wells. Recent developments in nanofluids have identified that the judicious injection of nano-particles into working drilling fluids may resolve a number of issues including borehole instability, lost circulation, torque and drag, pipe sticking problems, bit balling and reduction in drilling speed. The aim of this article is, therefore, to evaluate the rheological characteristics and lubricity of different nano-particles in water-based mud, with the potential to reduce costs via a decrease in drag and torque during the construction of highly deviated and ERD wells. Extensive results are presented for percentage in torque variation and coefficient of friction before and after aging. Rheology is evaluated via apparent viscosity, plastic viscosity and gel strength variation before and after aging for water-based muds (WBM). Results are included for silica and titanium nano-particles at different concentrations. These properties were measured before and after aging the mud samples at 80 °C during 16 h at static conditions. The best performance was shown with titanium nano-particles at a concentration of 0.60% (w/w) before aging.

Kelly mud saver valve sub

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reddoch, J.A.

1986-12-02

A mud saver valve is described for preventing drilling mud from escaping from a kelly when a drill string is broken below the kelly, the valve comprising: a tubular valve body having first and second ends, the first end being provided with means for attachment in fluid communicating relationship with the kelly, the second end being provided with means for attachment to the drill string; an annular seat fixed in the interior of the valve body adjacent its first end; a tubular closure member within the valve body. The closure member is provided with a selectively closed seating end formore » seating in valve closing engagement with the annular seat, an open non-seating end in fluid communicating relationship with the drill string, and an annular expansion in the outer diameter of the closure member adjacent the seating end; a top and bottom spacer ring disposed in sliding relationship around the tubular closure member intermediate the annular expansion and the non-seating end of the closure member. The spacer ring and annular expansion cooperatively define an annular chamber around the closure member; and a helical spring disposed around the closure member towards the annular seat.« less

IMPACT OF PHYSICAL AND CHEMICAL MUD CONTAMINATION ON WELLBORE CEMENT- FORMATION SHEAR BOND STRENGTH Authors: Arome Oyibo1 and Mileva Radonjic1 * 1. Craft and Hawkins Department of Petroleum Engineering, 2131 Patrick F. Taylor Hall, Louisiana State University, Baton Rouge, LA 70803, aoyibo1@tigers.lsu.edu, mileva@lsu.edu

NASA Astrophysics Data System (ADS)

Oyibo, A. E.

2013-12-01

Wellbore cement has been used to provide well integrity through zonal isolation in oil & gas wells and geothermal wells. Cementing is also used to provide mechanical support for the casing and protect the casing from corrosive fluids. Failure of cement could be caused by several factors ranging from poor cementing, failure to completely displace the drilling fluids to failure on the path of the casing. A failed cement job could result in creation of cracks and micro annulus through which produced fluids could migrate to the surface which could lead to sustained casing pressure, contamination of fresh water aquifer and blow out in some cases. In addition, cement failures could risk the release of chemicals substances from hydraulic fracturing into fresh water aquifer during the injection process. To achieve proper cementing, the drilling fluid should be completely displaced by the cement slurry. However, this is hard to achieve in practice, some mud is usually left on the wellbore which ends up contaminating the cement afterwards. The purpose of this experimental study is to investigate the impact of both physical and chemical mud contaminations on cement-formation bond strength for different types of formations. Physical contamination occurs when drilling fluids (mud) dries on the surface of the formation forming a mud cake. Chemical contamination on the other hand occurs when the drilling fluids which is still in the liquid form interacts chemically with the cement during a cementing job. We investigated the impact of the contamination on the shear bond strength and the changes in the mineralogy of the cement at the cement-formation interface to ascertain the impact of the contamination on the cement-formation bond strength. Berea sandstone and clay rich shale cores were bonded with cement cores with the cement-formation contaminated either physically or chemically. For the physically contaminated composite cores, we have 3 different sample designs: clean/not contaminated, scrapped and washed composite cores. Similarly, for the chemically contaminated samples we had 3 different sample designs: 0%, 5% and 10% mud contaminated composite cores. Shear test were performed on the composite cores to determine the shear bond strength and the results suggested that the detrimental impact of the contamination is higher when the cores are physically contaminated i.e. when we have mud cake present at the surface of the wellbore before a cement job is performed. Also, the results showed that shear bond strength is higher for sandstone formations as compared to shale formations. Material characterization analysis was carried out to determine the micro structural changes at the cement-formation interface. The results obtained from the SEM and micro CT images taken at the bond interface confirmed that chemical contamination caused substantial changes in the spatial distribution of minerals that impacted bond strength. Keywords: Cement-Formation bond strength, mud contamination, shale, sandstone and material characterization *Corresponding author

Defining Lithological Units by Cuttings, Core and Logging Data at Site C0009A in the Nankai Trough, Japan: IODP Expedition 319

NASA Astrophysics Data System (ADS)

Efimenko, N.; Schleicher, A. M.; Buchs, D. M.; Buret, C.; Kawabata, K.; Boutt, D. F.; Underwood, M.; Araki, E.; Byrne, T. B.; McNeill, L. C.; Saffer, D. M.; Eguchi, N. O.; Takahashi, K.; Toczko, S.; Scientists, E.

2009-12-01

The use of cuttings as an alternative or addition to core material is broadly debated in on-shore and off-shore drilling expeditions. Expedition 319 is the first IODP based Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) project using the riser-drilling method to collect cutting and core samples for scientific studies. One major scientific objective for this site was to characterise the lithology and deformation history of the Kumano forearc basin sediments and its underlying units through comparison of (i) cuttings, (ii) core, (iii) measurements while drilling, and (iv) wireline logging data. Cuttings were retrieved from each 5 m intervals from 703.9 to 1604 m, and cores were recovered from 1509.7 to 1593.9 m below sea floor. As core availability was limited, the study of cuttings was a crucial step in improving our understanding of their potential and limits for lithostratigraphical interpretations compared to core. Mineralogical and chemical analysis of cuttings and core, wireline logging data, and gamma ray data from MWD were available to define four lithostratigraphic units. These units are composed of mud and mudstone with coarser silty and sandy interbeds, and volcanic ash/tuff. Consistency between unit boundaries determined from cuttings and those determined from log data is good in terms of depth, with typical mismatches of less than 10m. Three significant problems affecting the preservation of cuttings were (1) mixing of cuttings as they travel from the drill face to the surface, (2) alteration of natural mineral and structure signatures, and (3) possible contamination from natural clay minerals with the polymer/bentonite drill mud. These difficulties can be overcome in part through the analysis of cuttings of similar sizes (1-4 mm), guided by the analyses of bulk cuttings. A more accurate quantitative characterisation of cuttings through the use of digital imaging might improve the description of lithofacies. Although the quality of cuttings is affected by caving and drilling mud contamination, our results clearly indicate that cuttings retrieval is a viable alternative to coring in ocean drilling. However, to improve the precision of lithostratigraphical observations and interpretations in critical intervals, the study of cores is needed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phelps, J.; Hoopingarner, J.

Effective techniques have been developed from work on dozens of North Sea Wells to minimize the amount of oil-based mud discharged to the sea while maintaining acceptable levels of solids. Pressure to reduce pollution during the course of drilling prompted the development of these techniques. They involve personnel and optimization of mud system and procedures. Case histories demonstrate that regulations may be met with economical techniques using existing technology. The benefits of low solids content are widely known, and are a key part of any successful mud program. Good solids control should result in lower mud costs and better drillingmore » performance. Operators have specified high-performance shakers to accomplish this and have revised their mud programs with lower and lower allowable drilled solids percentages. This will pay off in certain areas. But with the U.K. Department of Energy regulations requiring cuttings oil discharge content (CODC) to be less than 150 g of oil/kg of dry solids discharge that went into effect Jan. 1, 1989, oil-loss control has a higher profile in the U.K. sector of the North Sea.« less

40 CFR 147.950 - State-administered program.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., 1985 and January 20, 1986; (3)(i) Statewide Order Governing the Drilling for and Producing of Oil and... of Drilling Mud and Salt Water Generated from Drilling and Production of Oil and Gas Wells... 40 Protection of Environment 23 2014-07-01 2014-07-01 false State-administered program. 147.950...

40 CFR 147.950 - State-administered program.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., 1985 and January 20, 1986; (3)(i) Statewide Order Governing the Drilling for and Producing of Oil and... of Drilling Mud and Salt Water Generated from Drilling and Production of Oil and Gas Wells... 40 Protection of Environment 22 2010-07-01 2010-07-01 false State-administered program. 147.950...

40 CFR 147.950 - State-administered program.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., 1985 and January 20, 1986; (3)(i) Statewide Order Governing the Drilling for and Producing of Oil and... of Drilling Mud and Salt Water Generated from Drilling and Production of Oil and Gas Wells... 40 Protection of Environment 24 2013-07-01 2013-07-01 false State-administered program. 147.950...

40 CFR 147.950 - State-administered program.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., 1985 and January 20, 1986; (3)(i) Statewide Order Governing the Drilling for and Producing of Oil and... of Drilling Mud and Salt Water Generated from Drilling and Production of Oil and Gas Wells... 40 Protection of Environment 23 2011-07-01 2011-07-01 false State-administered program. 147.950...

40 CFR 147.950 - State-administered program.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., 1985 and January 20, 1986; (3)(i) Statewide Order Governing the Drilling for and Producing of Oil and... of Drilling Mud and Salt Water Generated from Drilling and Production of Oil and Gas Wells... 40 Protection of Environment 24 2012-07-01 2012-07-01 false State-administered program. 147.950...

Radiological survey of the covered and uncovered drilling mud depository.

PubMed

Jónás, Jácint; Somlai, János; Csordás, Anita; Tóth-Bodrogi, Edit; Kovács, Tibor

2018-08-01

In petroleum engineering, the produced drilling mud sometimes contains elevated amounts of natural radioactivity. In this study, a remediated Hungarian drilling mud depository was investigated from a radiological perspective. The depository was monitored before and after a clay layer was applied as covering. In this study, the ambient dose equivalent rate H*(10) of the depository has been measured by a Scintillator Probe (6150AD-b Dose Rate Meter). Outdoor radon concentration, radon concentration in soil gas, and in situ field radon exhalation measurements were carried out using a pulse-type ionization chamber (AlphaGUARD radon monitor). Soil gas permeability (k) measurements were carried out using the permeameter (RADON-JOK) in situ device. Geogenic radon potentials were calculated. The radionuclide content of the drilling mud and cover layer sample has been determined with an HPGe gamma-spectrometer. The gamma dose rate was estimated from the measured radionuclide concentrations and the results were compared with the measured ambient dose equivalent rate. Based on the measured results before and after covering, the ambient dose equivalent rates were 76 (67-85) nSv/h before and 86 (83-89) nSv/h after covering, radon exhalation was 9 (6-12) mBq/m 2 s before and 14 (5-28) mBq/m 2 s after covering, the outdoor radon concentrations were 11 (9-16) before and 13 (10-22) Bq/m 3 after covering and the soil gas radon concentrations were 6 (3-8) before and 24 (14-40) kBq/m 3 after covering. Soil gas permeability measurements were 1E-11 (7E-12-1E-11) and 1E-12 (5E-13-1E-12) m 2 and the calculated geogenic radon potential values were 6 (3-8) and 12 (6-21) before and after the covering. The main radionuclide concentrations of the drilling mud were C U-238 12 (10-15) Bq/kg, C Ra-226 31 (18-40) Bq/kg, C Th-232 35 (33-39) Bq/kg and C K-40 502 (356-673) Bq/kg. The same radionuclide concentrations in the clay were C U-238 31 (29-34) Bq/kg, C Ra-226 45 (40-51) Bq/kg, C Th-232 58 (55-60) Bq/kg and C K-40 651 (620-671) Bq/kg. According to our results, the drilling mud depository exhibits no radiological risk from any radiological aspects (radon, radon exhalation, gamma dose, etc.); therefore, long term monitoring activity is not necessary from the radiological point of view. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ascent velocity and dynamics of the Fiumicino mud eruption, Rome, Italy

NASA Astrophysics Data System (ADS)

Vona, A.; Giordano, G.; De Benedetti, A. A.; D'Ambrosio, R.; Romano, C.; Manga, M.

2015-08-01

In August 2013 drilling triggered the eruption of mud near the international airport of Fiumicino (Rome, Italy). We monitored the evolution of the eruption and collected samples for laboratory characterization of physicochemical and rheological properties. Over time, muds show a progressive dilution with water; the rheology is typical of pseudoplastic fluids, with a small yield stress that decreases as mud density decreases. The eruption, while not naturally triggered, shares several similarities with natural mud volcanoes, including mud componentry, grain-size distribution, gas discharge, and mud rheology. We use the size of large ballistic fragments ejected from the vent along with mud rheology to compute a minimum ascent velocity of the mud. Computed values are consistent with in situ measurements of gas phase velocities, confirming that the stratigraphic record of mud eruptions can be quantitatively used to infer eruption history and ascent rates and hence to assess (or reassess) mud eruption hazards.

Determining temperature limits of drilling fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thuren, J.B.; Chenevert, M.E.; Huang, W.T.W.

A capillary three tube viscometer has been designed which allows the measurement of rheological properties of time dependent non-Newtonian fluids in laminar flow at high temperture and pressure. The objective of this investigation is to determine the temperature stability of clay-water suspensions containing various drilling fluid additives. The additives studied consisted of viscosifiers, filtrate reducers, and chemical thinners. The temperature range studied is from room temperature to 550{sup 0}F. The system pressure is consistently maintained above the vapor pressure. The Bentonite and water standardized base mud used is equivalent to a 25 ppB fluid. Stabilization of the base mud ismore » necessary to obtain steady state laminar flow conditions and to obtain reliable temperature thinning effects with each temperature interval under investigation. Generally the temperature levels are maintained for one hour until 550{sup 0}F is attained. The last interval is then maintained until system fluid degradation occurs. Rheological measurements are obtained from differential pressure transducers located in a three diameter tube test section and externally at ambient conditions from a Baroid Rotational Viscometer. The power law model for non-Newtonian fluids is used to correlate the data.« less

Remedial Investigation Badger Army Ammunition Plant, Baraboo, Wisconsin. Volume 2. Appendices D.2 Through F

DTIC Science & Technology

1991-01-01

FILES FOR COMPOUNDS OF POTENTIAL CONCERN Vol. 7 APPENDIX 0 - HUMAN HEALTH RISK CALCULATIONS Vol. 7 APPENDIX P - INVENTORY OF SITE SPECIES Vol. 7...Driing Mud 0" 0 3 am 01 99 5 .Annula space seal:- GnmuldBsuryoni 0 33 Lbs/gal mud weight ... Benuar-siid shiny 3 33 16. Driling addives used 13 yesLbs...CONSTRUCTION REPORT / 5 WISCONSIN STATE BOARD OF HEALTH WELL DRILLING DIVISION JUL 11 |W Note: Section 32 of the Wisconsin Well Drilling Sanitary Code

The composition of muds from Columbus Marsh, Nevada

USGS Publications Warehouse

Hicks, W.B.

1915-01-01

The investigation of the dry lake of Columbus Marsh, in Nevada, which had for its economic motive the discovery of potash, was continued by the United States Geological Survey during the summer of 1913 under supervision of Hoyt S. Gale. The work done included the drilling of a shallow well near the old well 400 and the collection of a set of surface samples of muds from the marsh. This exploration, together with the chemical investigation of the samples thus collected, has furnished further data concerning the character of the mud flat and thrown additional light on the conditions there. The writer was associated with Mr. Gale during his study of this region and the field observations have recorded were made jointly and are results of mutual discussion. The accompanying map (fig. 1) is based on a plane-table survey made by Mr. Gale, and for this and other assistance the writer wishes to express due acknowledgment.

Phase 1 drilling operations at the Magma Energy Exploratory Well (LVF 51-20)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finger, J.T.; Jacobson, R.D.

1990-12-01

This report describes the Phase 1 drilling operations for the Magma Energy Exploratory Well near Mammoth Lakes, California. An important part of the Department of Energy's Magma Energy Program, this well is designed to reach an ultimate depth of 20,000 feet or a bottomhole temperature of 500{degree}C, whichever comes first. There will be four drilling phases, at least a year apart, with scientific investigations in the borehole between the drilling intervals. Phase 1 of this project resulted in a 20 inch cased hole to 2558 feet, with 185 feet of coring beyond that. This document comprises a narrative of themore » daily activities, copies of the daily mud and lithologic reports, time breakdowns of rig activities, inventories of lost circulation materials, temperature logs of the cored hole, and a strip chart mud log. 2 figs.« less

Drilling Fluid Contamination during Riser Drilling Quantified by Chemical and Molecular Tracers

NASA Astrophysics Data System (ADS)

Inagaki, F.; Lever, M. A.; Morono, Y.; Hoshino, T.

2012-12-01

Stringent contamination controls are essential to any type of microbiological investigation, and are particularly challenging in ocean drilling, where samples are retrieved from hundreds of meters below the seafloor. In summer 2012, Integrated Ocean Drilling Expedition 337 aboard the Japanese vessel Chikyu pioneered the use of chemical tracers in riser drilling while exploring the microbial ecosystem of coalbeds 2 km below the seafloor off Shimokita, Japan. Contamination tests involving a perfluorocarbon tracer that had been successfully used during past riserless drilling expeditions were complemented by DNA-based contamination tests. In the latter, likely microbial contaminants were targeted via quantitative polymerase chain reaction assays using newly designed, group-specific primers. Target groups included potential indicators of (a) drilling mud viscosifiers (Xanthomonas, Halomonas), (b) anthropogenic wastewater (Bifidobacterium, Blautia, Methanobrevibacter), and (c) surface seawater (SAR 11, Marine Group I Archaea). These target groups were selected based on past evidence suggesting viscosifiers, wastewater, and seawater as the main sources of microbial contamination in cores retrieved by ocean drilling. Analyses of chemical and molecular tracers are in good agreement, and indicate microorganisms associated with mud viscosifiers as the main contaminants during riser drilling. These same molecular analyses are then extended to subseafloor samples obtained during riserless drilling operations. General strategies to further reduce the risk of microbial contamination during riser and riserless drilling operations are discussed.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alan Black; Arnis Judzis

2003-01-01

Progress during current reporting year 2002 by quarter--Progress during Q1 2002: (1) In accordance to Task 7.0 (D. No.2 Technical Publications) TerraTek, NETL, and the Industry Contributors successfully presented a paper detailing Phase 1 testing results at the February 2002 IADC/SPE Drilling Conference, a prestigious venue for presenting DOE and private sector drilling technology advances. The full reference is as follows: IADC/SPE 74540 ''World's First Benchmarking of Drilling Mud Hammer Performance at Depth Conditions'' authored by Gordon A. Tibbitts, TerraTek; Roy C. Long, US Department of Energy, Brian E. Miller, BP America, Inc.; Arnis Judzis, TerraTek; and Alan D. Black,more » TerraTek. Gordon Tibbitts, TerraTek, will presented the well-attended paper in February of 2002. The full text of the Mud Hammer paper was included in the last quarterly report. (2) The Phase 2 project planning meeting (Task 6) was held at ExxonMobil's Houston Greenspoint offices on February 22, 2002. In attendance were representatives from TerraTek, DOE, BP, ExxonMobil, PDVSA, Novatek, and SDS Digger Tools. (3) PDVSA has joined the advisory board to this DOE mud hammer project. PDVSA's commitment of cash and in-kind contributions were reported during the last quarter. (4) Strong Industry support remains for the DOE project. Both Andergauge and Smith Tools have expressed an interest in participating in the ''optimization'' phase of the program. The potential for increased testing with additional Industry cash support was discussed at the planning meeting in February 2002. Progress during Q2 2002: (1) Presentation material was provided to the DOE/NETL project manager (Dr. John Rogers) for the DOE exhibit at the 2002 Offshore Technology Conference. (2) Two meeting at Smith International and one at Andergauge in Houston were held to investigate their interest in joining the Mud Hammer Performance study. (3) SDS Digger Tools (Task 3 Benchmarking participant) apparently has not negotiated a commercial deal with Halliburton on the supply of fluid hammers to the oil and gas business. (4) TerraTek is awaiting progress by Novatek (a DOE contractor) on the redesign and development of their next hammer tool. Their delay will require an extension to TerraTek's contracted program. (5) Smith International has sufficient interest in the program to start engineering and chroming of collars for testing at TerraTek. (6) Shell's Brian Tarr has agreed to join the Industry Advisory Group for the DOE project. The addition of Brian Tarr is welcomed as he has numerous years of experience with the Novatek tool and was involved in the early tests in Europe while with Mobil Oil. (7) Conoco's field trial of the Smith fluid hammer for an application in Vietnam was organized and has contributed to the increased interest in their tool. Progress during Q3 2002: (1) Smith International agreed to participate in the DOE Mud Hammer program. (2) Smith International chromed collars for upcoming benchmark tests at TerraTek, now scheduled for 4Q 2002. (3) ConocoPhillips had a field trial of the Smith fluid hammer offshore Vietnam. The hammer functioned properly, though the well encountered hole conditions and reaming problems. ConocoPhillips plan another field trial as a result. (4) DOE/NETL extended the contract for the fluid hammer program to allow Novatek to ''optimize'' their much delayed tool to 2003 and to allow Smith International to add ''benchmarking'' tests in light of SDS Digger Tools' current financial inability to participate. (5) ConocoPhillips joined the Industry Advisors for the mud hammer program. Progress during Q4 2002: (1) Smith International participated in the DOE Mud Hammer program through full scale benchmarking testing during the week of 4 November 2003. (2) TerraTek acknowledges Smith International, BP America, PDVSA, and ConocoPhillips for cost-sharing the Smith benchmarking tests allowing extension of the contract to add to the benchmarking testing program. (3) Following the benchmark testing of the Smith International hammer, representatives from DOE/NETL, TerraTek, Smith International and PDVSA met at TerraTek in Salt Lake City to review observations, performance and views on the optimization step for 2003. (4) The December 2002 issue of Journal of Petroleum Technology (Society of Petroleum Engineers) highlighted the DOE fluid hammer testing program and reviewed last years paper on the benchmark performance of the SDS Digger and Novatek hammers. (5) TerraTek's Sid Green presented a technical review for DOE/NETL personnel in Morgantown on ''Impact Rock Breakage'' and its importance on improving fluid hammer performance. Much discussion has taken place on the issues surrounding mud hammer performance at depth conditions.« less

Vergleich von hydraulischen und chemischen Sedimenteigenschaften aus Spül- und Kernbohrungen im Raum Peine (Norddeutschland)

NASA Astrophysics Data System (ADS)

Konrad, C.; Walther, W.; Reimann, T.; Rogge, A.; Stengel, P.; Well, R.

2008-03-01

Comparison of hydraulic and chemical properties of sediments from flush- and core drillings in the area of Peine (Germany). Because of financial constraints, investigations of nitrate metabolism are often based on disturbed borehole samples. It is arguable, however, whether disturbed samples are suitable for these types of investigations. Disadvantages of disturbed samples in comparison to undisturbed core samples are well known and include possible contamination of the sample by mud additives, destruction of the sediment formation and the insecurity concerning the correct depth allocation. In this study, boreholes were drilled at three locations to a maximum depth of 50 m. The extracted samples, as intact sediment cores and drill cuttings, were studied with regard to chemical and hydraulic parameters of the aquifer sediments. The results show: 1. hydraulic parameters are not affected by clay-based mud; 2. disturbed samples contain less fine grain material relative to the core samples, and the hydraulic conductivity can only be estimated from catch samples; 3. catch samples contain fewer reducing agents (sulphides, organic carbon) than core samples in hydraulically passive zones (defined as K < 10 6 m · s 1); 4. the results of analyses of disturbed and undisturbed core samples are in good agreement for hydraulically active zones (K ≥ 10 6 m · s 1).

Induction of Fish Biomarkers by Synthetic-Based Drilling Muds

PubMed Central

Gagnon, Marthe Monique; Bakhtyar, Sajida

2013-01-01

The study investigated the effects of chronic exposure of pink snapper (Pagrus auratus Forster), to synthetic based drilling muds (SBMs). Fish were exposed to three mud systems comprised of three different types of synthetic based fluids (SBFs): an ester (E), an isomerized olefin (IO) and linear alpha olefin (LAO). Condition factor (CF), liver somatic index (LSI), hepatic detoxification (EROD activity), biliary metabolites, DNA damage and stress proteins (HSP-70) were determined. Exposure to E caused biologically significant effects by increasing CF and LSI, and triggered biliary metabolite accumulation. While ester-based SBFs have a rapid biodegradation rate in the environment, they caused the most pronounced effects on fish health. IO induced EROD activity and biliary metabolites and LAO induced EROD activity and stress protein levels. The results demonstrate that while acute toxicity of SBMs is generally low, chronic exposure to weathering cutting piles has the potential to affect fish health. The study illustrates the advantages of the Western Australian government case-by-case approach to drilling fluid management, and highlights the importance of considering the receiving environment in the selection of SBMs. PMID:23894492

Fallon, Nevada FORGE Lithology Logs and Well 21-31 Drilling Data

DOE Data Explorer

Blankenship, Doug; Hinz, Nicholas; Faulds, James

2018-03-11

This submission includes lithology logs for all Fallon FORGE area wells; determined from core, cuttings, and thin section. Wells included are 84-31, 21-31, 82-36, FOH-3D, 62-36, 18-5, 88-24, 86-25, FOH-2, 14-36, 17-16, 34-33, 35A-11, 51A-20, 62-15, 72-7, 86-15, Carson_Strat_1_36-32, and several others. Lithology logs last updated 3/13/2018 with confirmation well 21-31 data, and revisited existing wells. Also included is well logging data for Fallon FORGE 21-31. Well logging data includes daily reports, well logs (drill rate, lithology, fractures, mud losses, minerals, temperature, gases, and descriptions), mud reports, drilling parameter plots, daily mud loss summaries, survey reports, progress reports, plan view maps (easting, northing), and wireline logs (caliper [with GR], triple combo [GR, caliper, SP, resistivity, array induction, density, photoelectric factor, and neutron porosity], array induction with linear correlation [GR, SP, Array Induction, caliper, conductivity], and monopole compression dipole shear [GR, SP, Caliper, sonic porosity, delta-T compressional, and delta-T shear])

Aerated drilling cutting transport analysis in geothermal well

NASA Astrophysics Data System (ADS)

Wakhyudin, Aris; Setiawan, Deni; Dwi Marjuan, Oscar

2017-12-01

Aeratad drilling widely used for geothermal drilling especially when drilled into predicted production zone. Aerated drilling give better performance on preventing lost circulation problem, improving rate of penetration, and avoiding drilling fluid invasion to productive zone. While well is drilled, cutting is produced and should be carried to surface by drilling fluid. Hole problem, especially pipe sticking will occur while the cutting is not lifted properly to surface. The problem will effect on drilling schedule; non-productive time finally result more cost to be spent. Geothermal formation has different characteristic comparing oil and gas formation. Geothermal mainly has igneous rock while oil and gas mostly sedimentary rock. In same depth, formation pressure in geothermal well commonly lower than oil and gas well while formation temperature geothermal well is higher. While aerated drilling is applied in geothermal well, Igneous rock density has higher density than sedimentary rock and aerated drilling fluid is lighter than water based mud hence minimum velocity requirement to transport cutting is larger than in oil/gas well drilling. Temperature and pressure also has impact on drilling fluid (aerated) density. High temperature in geothermal well decrease drilling fluid density hence the effect of pressure and temperature also considered. In this paper, Aerated drilling cutting transport performance on geothermal well will be analysed due to different rock and drilling fluid density. Additionally, temperature and pressure effect on drilling fluid density also presented to merge.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tranter, P.

Tender-assisted drilling (TAD) involves the use of tender support vessel (TSV) during the drilling phase of platform development to provide drilling utilities to the platform-mounted drilling package. The TSV provides facilities such as mud mixing, storage, pumping, bulk storage, hotel accommodations, and power. Thus, the platform topsides and jacket weight and size can be smaller and less expensive. The paper discusses the advantages and disadvantages of TAD, then describes the TAD vessel, semisubmersible, platform cost savings, accommodations, drilling and workovers, and field experience.

Geochemical monitoring of drilling fluids; A powerful tool to forecast and detect formation waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vuataz, F.D.; Brach, M.; Criaud, A.

1990-06-01

This paper describes a method based on the difference between the chemical compositions of formation and drilling fluids for analyzing drilling mud to forecast fluid-producing zones. The method was successfully applied in three boreholes in crystalline rocks in France. Subsequent geophysical logs and hydraulic tests confirmed the occurrence of flowing fractures.

20. Detail, Furnace A, shows the drill used to tap ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. Detail, Furnace A, shows the drill used to tap the furnace (at center left) and the 'mud gun' used to close it up with a clay plug (at lower right). Metal chute at center (next to drill) was used to clean out furnace prior to its abandonment. - Central Furnaces, 2650 Broadway, east bank of Cuyahoga River, Cleveland, Cuyahoga County, OH

30 CFR 250.514 - Well-control fluids, equipment, and operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... uppermost BOP; (2) A well-control, fluid-volume measuring device for determining fluid volumes when filling the hole on trips; and (3) A recording mud-pit-level indicator to determine mud-pit-volume gains and... the hole with drill pipe, the annulus shall be filled with well-control fluid before the change in...

30 CFR 250.1623 - Well-control fluids, equipment, and operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., (2) A well-control fluid-volume measuring device for determining fluid volumes when filling the hole on trips, and (3) A recording mud-pit-level indicator to determine mud-pit-volume gains and losses... the change in fluid level decreases the hydrostatic pressure 75 psi or every five stands of drill pipe...

Oil Palm Empty Fruit Bunch (OPEFB) Fiber as Lost Circulation Material (LCM) in Water Based Mud (WBM)

NASA Astrophysics Data System (ADS)

Ghazali, N. A.; Sauki, A.; Abu Bakar, N. F.; Mohamed, S.

2018-05-01

Lost Circulation Material (LCM) is an additive used to prevent lost of mud to the formation as a results from natural or induced fractured during drilling operation. Losses of mud could give great impact to the oil industry as it increases mud cost and rig time. The objective of this research was to investigate the effect of size and concentration of Oil Palm Empty Fruit Bunch (OPEFB) as LCM in water based mud (WBM). Several important properties of WBM rheology after adding the OPEFB namely plastic viscosity, apparent viscosity, yield point and gel strength were characterized. The sizes of OPEFB added into the WBM were 150μm, 250μm, 500μm and 1000μm while the concentration of OPEFB used were 5g, 10g, 15g and 20g in 350 mL of WBM. Results indicated that the plastic viscosity and apparent viscosity increased with increasing of the OPEFB concentrations. On the other hand, the plastic viscosity and apparent viscosity decreased with increasing sizes of OPEFB. Yield point increased as the concentration and size of OPEFB increases. This study indicated that OPEFB was effective to be used as LCM for size of 150μm and concentration of 15g whereby it produced least amount of filtrate volume as well as good control in mud rheology.

Polar organic compounds in pore waters of the Chesapeake Bay impact structure, Eyreville core hole: Character of the dissolved organic carbon and comparison with drilling fluids

USGS Publications Warehouse

Rostad, C.E.; Sanford, W.E.

2009-01-01

Pore waters from the Chesapeake Bay impact structure cores recovered at Eyreville Farm, Northampton County, Virginia, were analyzed to characterize the dissolved organic carbon. After squeezing or centrifuging, a small volume of pore water, 100 ??L, was taken for analysis by electrospray ionization-mass spectrometry. Porewater samples were analyzed directly without filtration or fractionation, in positive and negative mode, for polar organic compounds. Spectra in both modes were dominated by low-molecular-weight ions. Negative mode had clusters of ions differing by -60 daltons, possibly due to increasing concentrations of inorganic salts. The numberaverage molecular weight and weight-average molecular weight values for the pore waters from the Chesapeake Bay impact structure are higher than those reported for other aquatic sources of natural dissolved organic carbon as determined by electrospray ionization-mass spectrometry. In order to address the question of whether drilling mud fluids may have contaminated the pore waters during sample collection, spectra from the pore waters were compared to spectra from drilling mud fluids. Ions indicative of drilling mud fluids were not found in spectra from the pore waters, indicating there was no detectable contamination, and highlighting the usefulness of this analytical technique for detecting potential contamination during sample collection. ?? 2009 The Geological Society of America.

Interlake production established using quantitative hydrocarbon well-log analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lancaster, J.; Atkinson, A.

1988-07-01

Production was established in a new pay zone of the basal Interlake Formation adjacent to production in Midway field in Williams County, North Dakota. Hydrocarbon saturation, which was computed using hydrocarbon well-log (mud-log) data, and computed permeability encouraged the operator to run casing and test this zone. By use of drilling rig parameters, drilling mud properties, hydrocarbon-show data from the mud log, drilled rock and porosity descriptions, and wireline log porosity, this new technique computes oil saturation (percent of porosity) and permeability to the invading filtrate, using the Darcy equation. The Leonardo Fee well was drilled to test the Devonianmore » Duperow, the Silurian upper Interlake, and the Ordovician Red River. The upper two objectives were penetrated downdip from Midway production and there were no hydrocarbon shows. It was determined that the Red River was tight, based on sample examination by well site personnel. The basal Interlake, however, liberated hydrocarbon shows that were analyzed by this new technology. The results of this evaluation accurately predicted this well would be a commercial success when placed in production. Where geophysical log analysis might be questionable, this new evaluation technique may provide answers to anticipated oil saturation and producibility. The encouraging results of hydrocarbon saturation and permeability, produced by this technique, may be largely responsible for the well being in production today.« less

Sublethal metabolic responses of the hermatypic coral Madracis decactis exposed to drilling mud enriched with ferrochrome lignosulfonate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krone, M.A.; Biggs, D.C.

1981-06-01

Madracis decactis corals were exposed for 17 days in laboratory aquaria to suspensions of 100 ppm drilling mud spiked with 0, 3, and 10 ppm ferrochrome lignosulfonate (FCLS). During the first week of exposure, these corals increased their oxygen consumption and ammonium excretion, relative to uncontaminated controls. These corals exposed to the highest enrichments of FCLS demonstrated the greatest increases in respiration and excretion and also the largest variations in respiration and excretion between individual experimental animals. Corals reached their highest average rates of respiration and excretion by the end of the first week of continuous exposure. Rates then decreasedmore » during the next week and, after a secondary increase in excretion and respiration between days 10-13 which was most pronounced in those corals exposed to FCLS enrichment, leveled off at near-initial rates by the end of the second week. All corals exposed to FCLS reacted by reducing their polyp expansion behavior, although only the two showed mass polyp mortality. When exposure to drill mud + FCLS was discontinued, respiration and excretion of surviving corals remained low and stable while their polyp activity returned to normal levels within 48 hours.« less

Results of an adaptive environmental assessment modeling workshop concerning potential impacts of drilling muds and cuttings on the marine environment

USGS Publications Warehouse

Auble, Gregor T.; Andrews, Austin K.; Ellison, Richard A.; Hamilton, David B.; Johnson, Richard A.; Roelle, James E.; Marmorek, David R.

1983-01-01

Drilling fluids or "muds" are essential components of modern drilling operations. They provide integrity for the well bore, a medium for removal of formation cuttings, and lubrication and cooling of the drill bit and pipe. The modeling workshop described in this report was conducted September 14-18, 1981 in Gulf Breeze, Florida to consider potential impacts of discharged drilling muds and cuttings on the marine environment. The broad goals of the workshop were synthesis of information on fate and effects, identification of general relationships between drilling fluids and the marine environment, and identification of site-specific variables likely to determine impacts of drilling muds and cuttings in various marine sites. The workshop was structured around construction of a model simulating fate and effects of discharges from a single rig into open water areas of the Gulf of Mexico, and discussion of factors that might produce different fate and effects in enclosed areas such as bays and estuaries. The simulation model was composed of four connected submodels. A Discharge/Fate submodel dealt with the discharge characteristics of the rig and the subsequent fate of discharged material. Three effects submodels then calculated biological responses at distances away from the rig for the water column, soft bottom benthos (assuming the rig was located over a soft bottom environment), and hard bottom benthos (assuming the rig was located over a hard bottom environment). The model focused on direct linkages between the discharge and various organisms rather than on how the marine ecosystem itself is interconnected. Behavior of the simulation model indicated relatively localized effects of drilling muds and cuttings discharged from a single platform into open water areas. Water column fate and effects were dominated by rapid dilution. Effects from deposition of spent mud and cuttings were spatially limited with relatively rapid recovery, especially in soft bottom benthic communities which were conceptualized as being adapted to frequent storms. This behavior was generated by the set of assumptions about linkages and functional relationships used to construct the model. Areas of uncertainty included methods for extrapolating 96-hr LC50 so results to exposures of varying lengths and concentrations; recovery rates of benthic communities; responses to various depths and rates of burial; fate and effects of the plume in relationship to stratification layers; and long-term and sub-lethal effects of slightly elevated concentrations of discharged materials. Evaluation of the assumptions of the Soft Bottom Submodel suggest that the assumptions used may have been relatively liberal estimates of resiliency of these communities. Discussion of "closed" water bodies such as bays and estuaries indicated several reasons to expect different and more complex fate and effects behavior in these areas. These factors included different species and communities (such as aquatic macrophytes and oyster beds), more complex circulation and stratification patterns, and potentially more active resuspension processes. Much of the possible difference in behavior in these areas centers around the extent to which they are “closed” or in the relative residence times of water and sediments in these areas as they determine the long-term dispersion of discharged material. Despite the complexity and variability of these areas, a large body of knowledge (such as that concerning fate and physical effects of dredge spoil) that could be effectively employed in analysis of potential fate and physical effects in enclosed areas was identified.

Tuffaceous Mud is a Volumetrically Important Volcaniclastic Facies of Reararc Submarine Volcanism

NASA Astrophysics Data System (ADS)

Gill, J. B.; Bongiolo, E.; Miyazaki, T.; Hamelin, C.; Jutzeler, M.

2016-12-01

Unexpectedly, about 2/3 of the 1806 m of rock drilled during IODP Exp 350 on the flank of an Upper Miocene andesitic seamount in the Izu reararc was tuffaceous mud and tuffaceous mudstone that accumulated at high carbonate-free sedimentation rates (60-120 m/MY). This rate is several times faster than at adjacent sites in the forearc or incoming plate. Most tuffaceous muds contain <1% <2 mm-sized fragments of glass shards and plag±cpx crystals. Most muds are dacitic in bulk composition on an anhydrous, carbonate-free basis. They are intercalated with thin ash or tuff beds. The trace element and Sr-Nd-Hf-Pb isotope geochemistry of carbonate-free tuffaceous mud and mudstone indicates that >70% and often >90% of them consist of local volcanic materials that range from basalt to rhyolite. Most exceptions were deposited during Pleistocene glacial intervals. Consequently, tuffaceous mud is an important submarine volcaniclastic facies destined to become shale or slate in the geological record while retaining geochemical information about its provenance. Even though the drill site was <10 km from the summit of a 2-km-high and at times subaerially exposed seamount, and the sedimentation rate exceeded that in the adjacent forearc, tuffaceous mud was the principal reararc volcaniclastic facies. To explain this fine grain size, we infer that much of the submarine volcanism was explosive despite water depths approaching 2 km. The resulting very fine glass quickly becomes clay or is too small to be recognized in thin section or smear slides, and can be sampled only in sediment cores.

Optimizing Drilling Efficiency by PWD (Pressure-While-Drilling) Sensor in wells which were drilled in the Khazar-Caspian Sea of the Azerbaijan Republic

NASA Astrophysics Data System (ADS)

Amirov, Elnur

2017-04-01

Sperry Drilling Services' PWD sensor improve and support drilling efficiency by providing very important, real-time downhole pressure information that allows to make faster and better drilling decisions. The PWD service, provides accurate annular pressure, internal pressure and temperature measurements using any of well-known telemetry systems: positive mud pulse, negative mud pulse and electromagnetic. Pressure data can be transmitted in real time and recorded in downhole memory. In the pumpsoff mode, the minimum, maximum and average pressures observed during the non-circulating period are transmitted via mud pulse telemetry when circulation recommences. These measurements provide the knowledge to avoid lost circulation and detect flow/kicks before they happen. The PWD sensor also reduces the risk of problems related by unexpected fracture or collapse. Sperry's PWD sensor also helps to avoid lost circulation and flow/kick, which can lead to costly delays in drilling. Annular pressure increases often reflect ineffective cuttings removal and poor hole cleaning, both of which can lead to lost circulation. The PWD sensor detects the increase and drilling fluid parameters and operating procedures can be modified to improve hole-cleaning efficiency. On extended reach wells, real-time information helps to maintain wellbore pressures between safe operating limits and to monitor hole cleaning. The PWD sensor also provides early detection of well flows and kicks. A drop in pressure, can indicate gas, oil and water kicks. Because the sensor is making its measurement downhole, the PWD sensor makes it possible to detect such pressure drops earlier than more traditional surface measurements. The PWD sensor has high-accuracy quartz gauges and is able to record data because of its battery-powered operation. It is also extremely useful in specialized drilling environments, such as high-pressure/high-temperature, extended-reach and deepwater wells. When combined with the rig management system, surface and downhole measurements, can be compared for more accurate and extensive analysis. PWD sensor was utilized with encouraging results in many wells up to 3000-6000m subsurface reservoirs (these wells were drilled in the Khazar-Caspian region of the Azerbaijan Republic) and acquired PWD RT/RM data implemented for best drilling practices in other brand new drilled offset wells in order to help us achieve our mission to drill safe, faster, on target, optimize drilling efficiency, maximize well value and reservoir insight.

Effect of volumetric concentration of MWCNTs on the stability and thermal conductivity of nanofluids

NASA Astrophysics Data System (ADS)

Rehman, Wajid Ur; Bhat, A. H.; Suliamon, A. A.; Khan, Ihsan Ullah; Ullah, Hafeez

2016-11-01

Environmental concerns and running down of the fossil fuel deposits which are generally being used as base oil in Drilling Fluid/Mud have attended worldwide attention and thereby, researchers have focused on using environmentally friendly drilling fluids. This study demonstrates the preparation of drilling fluids and to explore the effect of increase in the volumetric concentration of nanoparticles on the stability and thermal conductivity of nanofluids. In this research, for the formation of nanofluids, Jatropha Seed Oil was used as the base oil with the addition of multi-walled carbon nanotubes as the nanoparticles using sonication technique. The raw multi-walled carbon nanotubes were characterized by using SEM for morphological examination. The prepared drilling fluid were characterized by using UV-Visible spectroscopic technique for analyzing the stability. Thermal Conductivity measurements were also carried out for heat transfer efficiency. It was observed that the heat transfer capability of the nanofluid ameliorates with the increase in the loading percentage of multi-walled carbon nanotubes.

Depositional environment, foraminifer content and ESR ages of Quaternary Gediz Delta Sediments (Eastern Aegean Sea, İzmir-Western Turkey)

NASA Astrophysics Data System (ADS)

Gökçe Benli, Ekin; Aydın, Hülya; İşintek, İsmail; Engin, Birol; Şengöçmen, Berna

2016-04-01

Sediments and fossil content of Gediz Delta (Eastern Aegean Sea - İzmir) were examined based on the drilling core samples of the YSK-C and SK-246 drilling. W-SW part of the Delta is represented by continental delta sediments up to 6 meters and shallow marine detritic sediments up to 35 meters in the YSK-C drilling. Continental part consists of an soiled, graveled, muddy and sandy sediment in terms of rich organic substance. As for marine part, it consists of bioclast, muddy, fine graveled sand and by repetition of pebble, sand and bioclast bearing mud layers. Bioclasts comprise of bivalvia, echinoid, ostracod, gastropod, foramifer and bryozoa fragments. Benthic foraminiferal fauna determinated in the marine levels are represented by 55 bethic, 2 planktonic species. These foraminifers and bioclasts reflect that the W-SW part of the delta, has been occured in marine conditions between 8-31m deep. E-NE part of the delta is generally represented by continental sediments up to 43.5m in SK-246 drilling. In addition, it includes marine levels in 18-19 m, 23-24 m and 36-37,5 m intervals. Continental sediments of E-NE part is generally represented by calcareous and sandy mud rocks which mostly includes ash, tuff, and pebble derived from Neogene volcanic rocks. As for marine levels, it is composed of calcareous mud stones and calcareous clay stones including very thin gastropod, bivalvia and ostracod in 18- 19 and 36-37.5 meters whereas it is represented by sandy mud stones including a great deal of bentic foraminifer, bivalvia, bryozoa, echinoid, gastropod in 23-24 metres. Thus show that E-NE part of the delta is usually in continental condition but it is occasionally covered by sea. In aging studies of YSK-C core done by ESR method, age of 8-9 m interval is determined to be 11. 376 ± 0,067 Ka; however ages of 10-11m and 24-25 m intervals are revealed to be 16.466 ± 0,016 Ka and 15.344 ± 0,021 Ka respectively; finally age of 25-26 m interval is found to be 19.995 ± 0,022 Ka. This results reflect while the W-SW part of the delta is in marine condition between 20 and 11 Ka, in the E-NE part of the delta, continental and marine conditions were repeated.

Digital archive of drilling mud weight pressures and wellbore temperatures from 49 regional cross sections of 967 well logs in Louisiana and Texas, onshore Gulf of Mexico basin

USGS Publications Warehouse

Burke, Lauri A.; Kinney, Scott A.; Kola-Kehinde, Temidayo B.

2011-01-01

This document provides the digital archive of in-situ temperature and drilling mud weight pressure data that were compiled from several historical sources. The data coverage includes the states of Texas and Louisiana in the Gulf of Mexico basin. Data are also provided graphically, for both Texas and Louisiana, as plots of temperature as a function of depth and pressure as a function of depth. The minimum, arithmetic average, and maximum values are tabulated for each 1,000-foot depth increment for temperature as well as pressure in the Texas and Louisiana data.

A brief geological history of Cockspur Island at Fort Pulaski National Monument, Chatham County, Georgia

USGS Publications Warehouse

Swezey, Christopher S.; Seefelt, Ellen L.; Parker, Mercer

2018-03-09

Fort Pulaski National Monument is located on Cockspur Island in Chatham County, Georgia, within the Atlantic Coastal Plain province. The island lies near the mouth of the Savannah River, and consists of small mounds (hummocks), salt marshes, and sediment dredged from the river. A 1,017-foot (ft) (310-meter [m])-deep core drilled at Cockspur Island in 2010 by the U.S. Geological Survey revealed several sedimentary units ranging in age from 43 million years old to present. Sand and mud are present at drilling depths from 0 to 182 ft (56 m), limestone is present at depths from 182 ft (56 m) to 965 ft (295 m), and glauconitic sand is present at depths from 965 ft (295 m) to 1,017 ft (310 m). The limestone and the water within the limestone are referred to collectively as the Floridan aquifer system, which is the primary source of drinking water for the City of Savannah and surrounding communities. In addition to details of the subsurface geology, this fact sheet identifies the following geologic materials used in the construction of Fort Pulaski: (1) granite, (2) bricks, (3) sandstone, and (4) lime mud with oyster shells.

Degradation of titanium drillpipe from corrosion and wear

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferg, T.E.; Aldrich, C.S.; Craig, B.D.

1993-06-01

Drilling deeper than 35,000 ft is limited by the extreme hook loads of steel drillpipe and temperature constraints of aluminum drillpipe. Titanium Alloys Ti-6Al-4V and Beta C have been proposed for use in drillpipe for wells deeper than 35,000 ft because of their high strength/weight ratios, superior high-temperature corrosion resistance, and thermal stability. Their suitability in drilling environments, however, has not been evaluated. To determine the corrosion and wear characteristics of two types of titanium-alloy drillpipe under dogleg conditions, a test cell was constructed to test titanium drillpipe joints in contact with API Spec. 5CT Grade P-110 casing in differentmore » drilling muds. Titanium-alloy pipe and Grade P-110 casing wear rates were measured, and tests showed that both titanium-alloy pipes exhibited much greater wear than did steel drillpipe in water-based mud under the same conditions. Test data showed that the total wear rate of Alloys Ti-6Al-4V and Beta C in a drilling environment is a combination of mechanical wear and corrosion.« less

Loaded Transducer Fpr Downhole Drilling Component

DOEpatents

Hall, David R.; Hall, H. Tracy; Pixton, David; Dahlgren, Scott; Sneddon, Cameron; Briscoe, Michael; Fox, Joe

2005-07-05

A robust transmission element for transmitting information between downhole tools, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The transmission element maintains reliable connectivity between transmission elements, thereby providing an uninterrupted flow of information between drill string components. A transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe. To close gaps present between transmission elements, transmission elements may be biased with a "spring force," urging them closer together.

Loaded transducer for downhole drilling components

DOEpatents

Hall, David R.; Hall, Jr., H. Tracy; Pixton, David S.; Briscoe, Michael A.; Dahlgren, Scott Steven; Fox, Joe; Sneddon, Cameron

2006-02-21

A robust transmission element for transmitting information between downhole tools, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The transmission element maintains reliable connectivity between transmission elements, thereby providing an uninterrupted flow of information between drill string components. A transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe. To close gaps present between transmission elements, transmission elements may be biased with a "spring force, urging them closer together."

Recovery and Lithologic Analysis of Sediment from Hole UT-GOM2-1-H002, Green Canyon 955, Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Kinash, N.; Cook, A.; Sawyer, D.; Heber, R.

2017-12-01

In May 2017 the University of Texas led a drilling and pressure coring expedition in the northern Gulf of Mexico, UT-GOM2-01. The holes were located in Green Canyon Block 955, where the Gulf of Mexico Joint Industry Project Leg II identified an approximately 100m thick hydrate-filled course-grained levee unit in 2009. Two separate wells were drilled into this unit: Holes H002 and H005. In Hole H002, a cutting shoe drill bit was used to collect the pressure cores, and only 1 of the 8 cores collected was pressurized during recovery. The core recovery in Hole H002 was generally poor, about 34%, while the only pressurized core had 45% recovery. In Hole H005, a face bit was used during pressure coring where 13 cores were collected and 9 cores remained pressurized. Core recovery in Hole H005 was much higher, at about 75%. The type of bit was not the only difference between the holes, however. Drilling mud was used throughout the drilling and pressure coring of Hole H002, while only seawater was used during the first 80m of pressure cores collected in Hole H005. Herein we focus on lithologic analysis of Hole H002 with the goal of documenting and understanding core recovery in Hole H002 to compare with Hole H005. X-ray Computed Tomography (XCT) images were collected by Geotek on pressurized cores, mostly from Hole H005, and at Ohio State on unpressurized cores, mostly from Hole H002. The XCT images of unpressurized cores show minimal sedimentary structures and layering, unlike the XCT images acquired on the pressurized, hydrate-bearing cores. Only small sections of the unpressurized cores remained intact. The unpressurized cores appear to have two prominent facies: 1) silt that did not retain original sedimentary fabric and often was loose within the core barrel, and 2) dense mud sections with some sedimentary structures and layering present. On the XCT images, drilling mud appears to be concentrated on the sides of cores, but also appears in layers and fractures within intact core sections. On microscope images, the drilling mud also appears to saturate the pores in some silt intervals. Further analysis of the unpressurized cores is planned, including X-ray diffraction, grain size analysis and porosity measurements. These results will be compared to the pressurized cores to understand if further lithologic factors could have affected core recovery.

Sub-lethal effects of water-based drilling muds on the deep-water sponge Geodia barretti.

PubMed

Edge, Katelyn J; Johnston, Emma L; Dafforn, Katherine A; Simpson, Stuart L; Kutti, Tina; Bannister, Raymond J

2016-05-01

Offshore oil and gas activities can result in the discharge of large amounts of drilling muds. While these materials have generally been regarded as non-toxic to marine organisms, recent studies have demonstrated negative impacts to suspension feeding organisms. We exposed the arctic-boreal sponge Geodia barretti to the primary particulate components of two water-based drilling muds; barite and bentonite. Sponges were exposed to barite, bentonite and a natural reference sediment at a range of total suspended solid concentrations (TSS = 0, 10, 50 or 100 mg/L) for 12 h after which we measured a suite of biomarker responses (lysosomal membrane stability, lipid peroxidation and glutathione). In addition, we compared biomarker responses, organic energy content and metal accumulation in sponges, which had been continuously or intermittently exposed to suspended barite and natural sediment for 14 d at relevant concentrations (10 and 30 mg TSS/L). Lysosomal membrane stability was reduced in the sponges exposed to barite at 50 and 100 mg TSS/L after just 12 h and at 30 mg TSS/L for both continuous and intermittent exposures over 14 d. Evidence of compromised cellular viability was accompanied by barite analysis revealing concentrations of Cu and Pb well above reference sediments and Norwegian sediment quality guidelines. Metal bioaccumulation in sponge tissues was low and the total organic energy content (determined by the elemental composition of organic tissue) was not affected. Intermittent exposures to barite resulted in less toxicity than continuous exposure to barite. Short term exposures to bentonite did not alter any biomarker responses. This is the first time that these biomarkers have been used to indicate contaminant exposure in an arctic-boreal sponge. Our results illustrate the potential toxicity of barite and the importance of assessments that reflect the ways in which these contaminants are delivered under environmentally realistic conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluation of generic types of drilling fluid using a risk-based analytic hierarchy process.

PubMed

Sadiq, Rehan; Husain, Tahir; Veitch, Brian; Bose, Neil

2003-12-01

The composition of drilling muds is based on a mixture of clays and additives in a base fluid. There are three generic categories of base fluid--water, oil, and synthetic. Water-based fluids (WBFs) are relatively environmentally benign, but drilling performance is better with oil-based fluids (OBFs). The oil and gas industry developed synthetic-based fluids (SBFs), such as vegetable esters, olefins, ethers, and others, which provide drilling performance comparable to OBFs, but with lower environmental and occupational health effects. The primary objective of this paper is to present a methodology to guide decision-making in the selection and evaluation of three generic types of drilling fluids using a risk-based analytic hierarchy process (AHP). In this paper a comparison of drilling fluids is made considering various activities involved in the life cycle of drilling fluids. This paper evaluates OBFs, WBFs, and SBFs based on four major impacts--operations, resources, economics, and liabilities. Four major activities--drilling, discharging offshore, loading and transporting, and disposing onshore--cause the operational impacts. Each activity involves risks related to occupational injuries (safety), general public health, environmental impact, and energy use. A multicriteria analysis strategy was used for the selection and evaluation of drilling fluids using a risk-based AHP. A four-level hierarchical structure is developed to determine the final relative scores, and the SBFs are found to be the best option.

Determining the Area of Review for Industrial Waste Disposal Wells.

DTIC Science & Technology

1981-12-01

pressure increases sufficiently to force formation fluids and/or injected wastes up abandoned well bores to contaminate underground sources of drinking...Drilling Mud Circulating System . . 72 9. Increase in Gel Strength of Various Mud Types With Time . . . . . . . . . . . . . . . . . . 96 10. Gel... increased fluid pressure in a disposal zone which results from a waste injection operation may force injected and/or formation fluid to migrate up an

30 CFR 250.614 - Well-control fluids, equipment, and operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... well is shut in and secured. (b) When coming out of the hole with drill pipe or a workover string, the... string and drill collars that may be pulled prior to filling the hole and the equivalent well-control... fluid volumes when filling the hole on trips; and (3) A recording mud-pit-level indicator to determine...

Deformation Analyses and Lithologic Characterization in Overpressured Basins Based on Logging While Drilling and Wireline Results from the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Iturrino, G. J.; Pirmez, C.; Moore, J. C.; Reichow, M. K.; Dugan, B. E.; Sawyer, D. E.; Flemings, P. B.; Shipboard Scientific Party, I.

2005-12-01

IODP Expedition 308 drilled transects along the Brazos-Trinity IV and Ursa Basins in the western and eastern Gulf of Mexico, respectively, for examining how sedimentation, overpressure, fluid flow, and deformation are coupled in passive margin settings. A total of eight holes were logged using either logging while drilling (LWD) or wireline techniques to evaluate the controls on slope stability, understand the timing of sedimentation and slumping, establish the petrophysical properties of shallow sediments, and provide a better understanding of turbidite systems. Overall, the log responses vary for the different lithostratigraphic units and associated regional seismic reflectors. The data acquired also make bed-to-bed correlation between sites possible, which is valuable for the study of sandy turbidites and studies of regional deformation. The thick sedimentary successions drilled at these basins show records of the evolution of channel-levee systems composed of low relief channels that were incapable of confining the turbidity currents causing an overspill of sand and silt. In addition, mass transport deposits at shallow depths, and transitions between interbedded silt, sand, and mud units are common features identified in many of the downhole logging data. In the Ursa Basin sediments, resistivity-at-the-bit images show significant deformation of the overlying hemipelagic drape and distal turbidites that were drilled in these areas. Numerous dipping beds throughout these intervals with dips ranging from 5 to 55 degrees confirm core observations. Steeply deformed beds, with dips as high as 65 degrees, and folded and faulted beds suggest down slope remobilization as mass-transport deposits. Resistivity images also show evidence of these mass-transport deposits where steep dips and folds suggest the presence of overturned beds within a series of cyclic intervals that we interpret as a succession of sand-silt-mud lamina. Preliminary structural analyses suggest that many of the deformation features trend in an E-W direction with the majority dipping to the north.

Method of deep drilling

DOEpatents

Colgate, Stirling A.

1984-01-01

Deep drilling is facilitated by the following steps practiced separately or in any combination: (1) Periodically and sequentially fracturing zones adjacent the bottom of the bore hole with a thixotropic fastsetting fluid that is accepted into the fracture to overstress the zone, such fracturing and injection being periodic as a function of the progression of the drill. (2) Casing the bore hole with ductile, pre-annealed casing sections, each of which is run down through the previously set casing and swaged in situ to a diameter large enough to allow the next section to run down through it. (3) Drilling the bore hole using a drill string of a low density alloy and a high density drilling mud so that the drill string is partially floated.

Transducer for downhole drilling components

DOEpatents

Hall, David R; Fox, Joe R

2006-05-30

A robust transmission element for transmitting information between downhole tools, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The transmission element maintains reliable connectivity between transmission elements, thereby providing an uninterrupted flow of information between drill string components. A transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe. The transmission element may include an annular housing forming a trough, an electrical conductor disposed within the trough, and an MCEI material disposed between the annular housing and the electrical conductor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

William C. Maurer; William J. McDonald; Thomas E. Williams

Underbalanced drilling is experiencing growth at a rate that rivals that of horizontal drilling in the mid-1980s and coiled-tubing drilling in the 1990s. Problems remain, however, for applying underbalanced drilling in a wider range of geological settings and drilling environments. This report addresses developments under this DOE project to develop products aimed at overcoming these problems. During Phase I of the DOE project, market analyses showed that up to 12,000 wells per year (i.e., 30% of all wells) will be drilled underbalanced in the U.S.A. within the next ten years. A user-friendly foam fluid hydraulics model (FOAM) was developed formore » a PC Windows environment during Phase I. FOAM predicts circulating pressures and flow characteristics of foam fluids used in underbalanced drilling operations. FOAM is based on the best available mathematical models, and was validated through comparison to existing models, laboratory test data and field data. This model does not handle two-phase flow or air and mist drilling where the foam quality is above 0.97. This FOAM model was greatly expanded during Phase II including adding an improved foam rheological model and a ''matching'' feature that allows the model to be field calibrated. During Phase I, a lightweight drilling fluid was developed that uses hollow glass spheres (HGS) to reduce the density of the mud to less than that of water. HGS fluids have several advantages over aerated fluids, including they are incompressible, they reduce corrosion and vibration problems, they allow the use of mud-pulse MWD tools, and they eliminate high compressor and nitrogen costs. Phase II tests showed that HGS significantly reduce formation damage with water-based drilling and completion fluids and thereby potentially can increase oil and gas production in wells drilled with water-based fluids. Extensive rheological testing was conducted with HGS drilling and completion fluids during Phase II. These tests showed that the HGS fluids act similarly to conventional fluids and that they have potential application in many areas, including underbalanced drilling, completions, and riserless drilling. Early field tests under this project are encouraging. These led to limited tests by industry (which are also described). Further field tests and cost analyses are needed to demonstrate the viability of HGS fluids in different applications. Once their effectiveness is demonstrated, they should find widespread application and should significantly reduce drilling costs and increase oil and gas production rates. A number of important oilfield applications for HGS outside of Underbalanced Drilling were identified. One of these--Dual Gradient Drilling (DGD) for deepwater exploration and development--is very promising. Investigative work on DGD under the project is reported, along with definition of a large joint-industry project resulting from the work. Other innovative products/applications are highlighted in the report including the use of HGS as a cement additive.« less

Recent performance of the dual-resistivity MWD tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagstaff, J.D.; Grupping, T.I.F.

1990-06-01

This article reports on the dual-resistivity MWD tool, which uses section of the drill collar as electrodes and provides two independent resistivity measurements: a principal well-focused lateral measurement of the current flowing radially from a defined segment of the drill collar and a secondary axial or bit measurement of the current flowing from a defined portion of the lower bottomhole assembly (BHA). In oil-based muds, a single (bit) measurement is made of the current flowing to the formation through the drill bit.

Plasmid incidence in bacteria from deep subsurface sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fredrickson, J.K.; Hicks, R.J.; Li, S.W.

Bacteria were isolated from deep terrestrial subsurface sediments underlying the coastal plain of South Carolina. A total of 163 isolates from deep sediments, surface soil, and return drill muds were examined for plasmid DNA content and resistance to the antibiotics penicillin, ampicillin, carbenicillin, streptomycin, kanamycin, and tetracycline. MICs of Cu{sup 2+}, Cr{sup 3+}, and Hg{sup 2+} for each isolate were also determined. The overall frequency of plasmid occurrence in the subsurface bacteria was 33%. Resistance was most frequent to penicillin (70% of all isolates), ampicillin (49%), and carbenicillin (32%) and was concluded to be related to the concentrations of themore » individual antibiotics in the disks used for assaying resistance and to the production of low levels of {beta}-lactamase. The frequencies of resistance to penicillin and ampicillin were significantly greater for isolates bearing plasmids than for plasmidless isolates; however, resistance was not transferable to penicillin-sensitive Escherichia coli. Hybridization of subsurface bacterial plasmids and chromosomal DNA with a whole-TOL-plasmid (pWWO) probe revealed some homology of subsurface bacterial plasmid and chromosomal DNAs, indicating a potential for those bacterial to harbor catabolic genes on plasmids or chromosomes. The incidences of antibiotic resistance and MICs of metals for subsurface bacteria were significantly different from those drill mud bacteria, ruling out the possibility that bacteria from sediments were derived from drill muds.« less

40 CFR Appendix 2 to Subpart A of... - Drilling Fluids Toxicity Test

Code of Federal Regulations, 2011 CFR

2011-07-01

... are designed to minimize sample contamination and alteration of the physical or chemical properties of... wet ice (do not use dry ice) and continuously maintained at 0-4 °C until the time of testing. (3) Bulk... use. (5) Most drilling mud samples may be stored for periods of time longer than 2 weeks prior to...

40 CFR Appendix 2 to Subpart A of... - Drilling Fluids Toxicity Test

Code of Federal Regulations, 2010 CFR

2010-07-01

... are designed to minimize sample contamination and alteration of the physical or chemical properties of... wet ice (do not use dry ice) and continuously maintained at 0-4 °C until the time of testing. (3) Bulk... use. (5) Most drilling mud samples may be stored for periods of time longer than 2 weeks prior to...

Drilling and production aspects of horizontal wells in the Austin Chalk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheikholeslami, B.A.; Scholhman, B.W.; Seidel, F.A.

1991-07-01

This paper discusses testing of horizontal technology for use in the highly fractured Giddings oil field. Three short-and seven medium-radius wells were drilled successfully in the Austin Chalk formation. The paper discusses well plans, bottomhole assemblies, trajectory control, telemetry, mud systems, hydraulics, hole cleaning, casing design, cementing, problems encountered, formation evaluation, completions, and reservoir response.

Alternatives Analysis Amchitka Island Mud Pit Cap Repair, Amchitka, Alaska January 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Darr, Paul S.

2016-01-01

The U.S. Department of Energy (DOE) Office of Legacy Management (LM) manages the Nevada Offsites program, which includes a series of reclaimed drilling mud impoundments on Amchitka Island, Alaska (Figure 1). Navarro Research and Engineering, Inc. is the Legacy Management Support contractor (the Contractor) for LM. The Contractor has procured Tetra Tech, Inc. to provide engineering support to the Amchitka mud pit reclamation project. The mud pit caps were damaged during a 7.9-magnitude earthquake that occurred in 2014. The goals of the current project are to investigate conditions at the mud pit impoundments, identify feasible alternatives for repair of themore » cover systems and the contents, and estimate relative costs of repair alternatives. This report presents descriptions of the sites and past investigations, existing conditions, summaries of various repair/mitigation alternatives, and direct, unburdened, order-of-magnitude (-15% to +50%) associated costs.« less

Study the effect of polymers on the stability and rheological properties of oil-in-water (O/W) Pickering emulsion muds

NASA Astrophysics Data System (ADS)

Jha, Praveen Kumar; Mahto, Vikas; Saxena, Vinod Kumar

2018-05-01

A new type of oil-in-water (O/W) Pickering emulsion systems, which were prepared by polymers such as xanthan gum, carboxymethyl cellulose (CMC), and sodium lignosulfonate have been investigated for their properties as multifunctional emulsion muds with respect to rheological control and filtration control properties. Diesel oil was used as dispersed phase and KCl-brine as continuous phase in the developed emulsions. Initially, rheological parameters like apparent viscosity, plastic viscosity, gel strength, and filtration control properties were measured using recommended practices. Emulsion stability was analyzed using steady state shear stress-shear rate and oscillatory (dynamic) rheological measurement techniques. The emulsions were found to exhibit shear-thinning (pseudoplastic) behavior. Experiments conducted for oscillatory rheological measurements have shown that emulsions are stable as per the stability criteria G' (elastic modulus) > G'' (loss modulus) and both are independent of changing ω (Frequency). These fluids have shown stable properties upto 70°C which shows that they can be used as drilling muds for drilling oil and gas wells.

Factors controlling mud accumulation in the Heuksan mud belt off southwestern Korea

NASA Astrophysics Data System (ADS)

Chang, Tae Soo; Ha, Hun Jun; Chun, Seung Soo

2015-12-01

The Heuksan mud belt (hereafter HMB) is 20~50 km wide, ~200 km long, and ~50 m thick, having accumulated in the course of the Holocene transgression on the tide-dominated epicontinental shelf southwest of Korea. The internal architecture of the HMB is characterized by offshore prograding clinoforms. Of particular interest are the depositional processes responsible for this anomalously thick mud accumulation within a relatively short period of time. Tidal currents are important in the dispersal of mud in the HMB, although these alone cannot explain such an enormous mud deposit. In order to understand the formative processes of the HMB, a detailed sedimentary facies analysis, including high-resolution grain-size measurements, has been conducted on more than 30 short cores and three long drill cores recovered from the mud belt. Five major mud facies were identified. Of these, mud sequences showing a thickening-thinning trend of alternating silt and clay laminae suggestive of a tidal origin occur dominantly at inner to mid shelf locations. By contrast, internally structureless muds with sharp bases and no bioturbation, which are interpreted of representing fluid-mud deposits, are widespread at mid to outer shelf locations. Wave-generated mud ripples and storm beds on the inner shelf suggest that storm waves in winter resuspend previously deposited mud to form near-bed fluid-mud suspensions with resulting gravity-driven mud transport across the low-gradient outer shelf. This previously not recognized process is probably a major factor controlling depositional processes on the giant mud belt, enabling rapid accumulation and offshore progradation even during transgression, i.e., at times of sea-level rise.

GHGfrack: An Open-Source Model for Estimating Greenhouse Gas Emissions from Combustion of Fuel during Drilling and Hydraulic Fracturing.

PubMed

Vafi, Kourosh; Brandt, Adam

2016-07-19

This paper introduces GHGfrack, an open-source engineering-based model that estimates energy consumption and associated GHG emissions from drilling and hydraulic fracturing operations. We describe verification and calibration of GHGfrack against field data for energy and fuel consumption. We run GHGfrack using data from 6927 wells in Eagle Ford and 4431 wells in Bakken oil fields. The average estimated energy consumption in Eagle Ford wells using lateral hole diameters of 8 (3)/4 and 6 (1)/8 in. are 2.25 and 2.73 TJ/well, respectively. The average estimated energy consumption in Bakken wells using hole diameters of 6 in. for horizontal section is 2.16 TJ/well. We estimate average greenhouse gas (GHG) emissions of 419 and 510 tonne of equivalent CO2 per well (tonne of CO2 eq/well) for the two aforementioned assumed geometries in Eagle Ford, respectively, and 417 tonne of CO2 eq/well for the case of Bakken. These estimates are limited only to GHG emissions from combustion of diesel fuel to supply energy only for rotation of drill string, drilling mud circulation, and fracturing pumps. Sensitivity analysis of the model shows that the top three key variables in driving energy intensity in drilling are the lateral hole diameter, drill pipe internal diameter, and mud flow rate. In hydraulic fracturing, the top three are lateral casing diameter, fracturing fluid volume, and length of the lateral.

30 CFR 250.1617 - Application for permit to drill.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Formation fracture gradients; (iii) Potential lost circulation zones; (iv) Mud weights; (v) Casing setting... various casing strings, fracture gradients of the exposed formations, casing setting depths, and cementing...

30 CFR 250.1617 - Application for permit to drill.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Formation fracture gradients; (iii) Potential lost circulation zones; (iv) Mud weights; (v) Casing setting... various casing strings, fracture gradients of the exposed formations, casing setting depths, and cementing...

30 CFR 250.1617 - Application for permit to drill.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Formation fracture gradients; (iii) Potential lost circulation zones; (iv) Mud weights; (v) Casing setting... various casing strings, fracture gradients of the exposed formations, casing setting depths, and cementing...

Alterations in bottom sediment physical and chemical characteristics at the Terra Nova offshore oil development over ten years of drilling on the grand banks of Newfoundland, Canada

NASA Astrophysics Data System (ADS)

DeBlois, Elisabeth M.; Paine, Michael D.; Kilgour, Bruce W.; Tracy, Ellen; Crowley, Roger D.; Williams, Urban P.; Janes, G. Gregory

2014-12-01

This paper describes sediment composition at the Terra Nova offshore oil development. The Terra Nova Field is located on the Grand Banks approximately 350 km southeast of Newfoundland, Canada, at an approximate water depth of 100 m. Surface sediment samples (upper 3 cm) were collected for chemical and particle size analyses at the site pre-development (1997) and in 2000-2002, 2004, 2006, 2008 and 2010. Approximately 50 stations have been sampled in each program year, with stations extending from less than 1 km to a maximum of 20 km from source (drill centres) along five gradients, extending to the southeast, southwest, northeast, northwest and east of Terra Nova. Results show that Terra Nova sediments were contaminated with >C10-C21 hydrocarbons and barium-the two main constituents of synthetic-based drilling muds used at the site. Highest levels of contamination occurred within 1 to 2 km from source, consistent with predictions from drill cuttings dispersion modelling. The strength of distance gradients for >C10-C21 hydrocarbons and barium, and overall levels, generally increased as drilling progressed but decreased from 2006 to 2010, coincident with a reduction in drilling. As seen at other offshore oil development sites, metals other than barium, sulphur and sulphide levels were elevated and sediment fines content was higher in the immediate vicinity (less than 0.5 km) of drill centres in some sampling years; but there was no strong evidence of project-related alterations of these variables. Overall, sediment contamination at Terra Nova was spatially limited and only the two major constituents of synthetic-based drilling muds used at the site, >C10-C21 hydrocarbons and barium, showed clear evidence of project-related alternations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gavignet, A.A.; Sobey, I.J.

At present, drilling of highly deviated wells is complicated by the possibility of the formation of a thick bed of cuttings at low flow rates. The bed of cuttings can cause large torque loads on drill pipe and can fall back around the bit resulting in a stuck bit. Previous investigators have made experimental observations which show that bed formation is characterized by a relatively rapid increase in bed thickness as either the flow rate is lowered past some critical value, or as the deviation from the vertical increases. The authors present a simple model which explains these observations. Themore » model shows that the bed thickness is controlled by the interfacial stress caused by the different velocities of the mud and the cuttings layer. The results confirm previous observations that bed formation is relatively insensitive to mud rheology. Eccentricity of the drill pipe in the hole is an important factor. The model is used to determine critical flow rate needed to prevent the formation of a thick bed of cuttings and the inclination, hole size and rate of penetration are varied.« less

Drilling plastic formations using highly polished PDC cutters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, R.H.; Lund, J.B.; Anderson, M.

1995-12-31

Highly plastic and over-pressured formations are troublesome for both roller cone and PDC bits. Thus far, attempts to increase penetration rates in these formations have centered around re-designing the bit or modifying the cutting structure. These efforts have produced only moderate improvements. This paper presents both laboratory and field data to illustrate the benefits of applying a mirror polished surface to the face of PDC cutters in drilling stressed formations. These cutters are similar to traditional PDC cutters, with the exception of the reflective mirror finish, applied to the diamond table surfaces prior to their installation in the bit. Resultsmore » of tests conducted in a single point cutter apparatus and a full-scale drilling simulator will be presented and discussed. Field results will be presented that demonstrate the effectiveness of polished cutters, in both water and oil-based muds. Increases in penetration rates of 300-400% have been observed in the Wilcox formation and other highly pressured shales. Typically, the beneficial effects of polished cutters have been realized at depths greater than 7000 ft, and with mud weights exceeding 12 ppg.« less

Footprint, weathering, and persistence of synthetic-base drilling mud olefins in deep-sea sediments following the Deepwater Horizon disaster.

PubMed

Stout, Scott A; Payne, James R

2017-05-15

Olefin-based synthetic-based drilling mud (SBM) was released into the Gulf of Mexico as a result of the Deepwater Horizon (DWH) disaster in 2010. We studied the composition of neat SBM and, using conventional GC-FID, the extent, concentration, and chemical character of SBM-derived olefins in >3600 seafloor sediments collected in 2010/2011 and 2014. SBM-derived (C 14 -C 20 ) olefins occurred (up to 10cm deep) within a 6.5km 2 "footprint" around the well. The olefin concentration in most sediments decreased an order of magnitude between 2010/2011 and 2014, at least in part due to biodegradation, evidenced by the preferential loss C 16 and C 18 linear (α- and internal) versus branched olefins. Based on their persistence for 4-years in sediments around the Macondo well, and 13-years near a former unrelated drill site (~62km away), weathered SBM-derived olefins released during the DWH disaster are anticipated to persist in deep-sea sediment for (at least) a comparable duration. Copyright © 2017 Elsevier Ltd. All rights reserved.

Phospholipids Polysaccharide and Its Application as Inhibitive Drilling Fluid Additive

NASA Astrophysics Data System (ADS)

Gu, Xue-Fan; Hu, Wei-Min; Zhang, Fan; Du, Wei-Chao; Zhang, Qiang; Zhang, Jie; Zhang, Yong-Ming; Chen, Gang

2018-03-01

For the improvement of solubility and the performance of the sample that derived plant polysaccharide(SJ) in drilling fluid based on water, which was improved by phosphoric esterification with phospholipids reagent. The conditions of the reaction were discussed by orthogonal ways in four factors and three levels, and the optimization of handling approaches were found out: With pH=12 at the temperature of 80°C, the mass ratio between phospholipids agent and SJ is 0.1g/1g. The viscosity about the system added by sulfonated SJ (SJP) was extremely increased and below 120°, rheological properties had a slight change. The inhibitive ability of SJP is assessed by the mud ball immersing tests and clay-swelling experiments, that is apparently better than SJ and even 4wt% KCl in free water.

Implementing Monitored Natural Attenuation and Expediting Closure at Fuel-Release Sites

DTIC Science & Technology

2004-08-01

Center for Environmental Excellence AFCEE/ERS Air Force Center for Environmental Excellence/Science and Engineering Division AFRPA Air Force Real...auger, air - or mud- rotary , cable-tool) was and is dependent on the target drilling depths and the types of subsurface materials expected to be...95(2000) ASTM. 1995c. Guide for the use of direct air - rotary drilling for geoenvironmental exploration and installation of subsurface water quality

Benthic foraminiferal responses to operational drill cutting discharge in the SW Barents Sea - a case study.

NASA Astrophysics Data System (ADS)

Aagaard-Sørensen, Steffen; Junttila, Juho; Dijkstra, Noortje

2016-04-01

Petroleum related exploration activities started in the Barents Sea 1980, reaching 97 exploration wells drilled per January 2013. The biggest operational discharge from drilling operations in the Barents Sea is the release of drill cuttings (crushed seabed and/or bedrock) and water based drilling muds including the commonly used weighing material barite (BaSO4). Barium (Ba), a constituent of barite, does not degrade and can be used to evaluate dispersion and accumulation of drill waste. The environmental impact associated with exploration drilling within the Goliat Field, SW Barents Sea in 2006 was evaluated via a multiproxy investigation of local sediments. The sediments were retrieved in November 2014 at ~350 meters water depth and coring sites were selected at distances of 5, 30, 60, 125 and 250 meters from the drill hole in the eastward downstream direction. The dispersion pattern of drill waste was estimated via measurements of sediment parameters including grain size distribution and water content in addition to heavy metal and total organic carbon contents. The environmental impact was evaluated via micro faunal analysis based on benthic foraminiferal (marine shell bearing protists) fauna composition and concentration changes. Observing the sediment parameters, most notably Ba levels, reveals that dispersion of drill waste was limited to <125 meters from the drill site with drill waste thicknesses decreasing downstream. The abruptness and quantity of drill waste sedimentation initially smothered the foraminiferal fauna at ≤ 30 meters from the drill site, while at a distance of 60 meters, the fauna seemingly survived and bioturbation persisted. Analysis of the live (Nov 2014) foraminiferal fauna reveals a natural species composition at all distances from the drill site within the top sediments (0-5 cm core depth). Furthermore, the fossil foraminiferal fauna composition found within post-impacted top sediment sections, particularly in the cores situated at 30 and 60 meters from the drill site, suggests that reestablishment of the foraminiferal fauna likely commenced shortly after cessation of drilling activity.

Problem analysis of geotechnical well drilling in complex environment

NASA Astrophysics Data System (ADS)

Kasenov, A. K.; Biletskiy, M. T.; Ratov, B. T.; Korotchenko, T. V.

2015-02-01

The article examines primary causes of problems occurring during the drilling of geotechnical wells (injection, production and monitoring wells) for in-situ leaching to extract uranium in South Kazakhstan. Such a drilling problem as hole caving which is basically caused by various chemical and physical factors (hydraulic, mechanical, etc.) has been thoroughly investigated. The analysis of packing causes has revealed that this problem usually occurs because of insufficient amount of drilling mud being associated with small cross section downward flow and relatively large cross section upward flow. This is explained by the fact that when spear bores are used to drill clay rocks, cutting size is usually rather big and there is a risk for clay particles to coagulate.

Drill cuttings mount formation study

NASA Astrophysics Data System (ADS)

Teh, Su Yean; Koh, Hock Lye

2014-07-01

Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

Overpressure Prediction From Seismic Data: Implications on Drilling Safety

NASA Astrophysics Data System (ADS)

Osinowo, O. O.; Oladunjoye, M. A.; Olayinka, A. I.

2007-12-01

High rate of sediment influx into the Niger Delta via river Niger coupled with high rate of basin subsidence, very thick clayey members of Agbada and Akata Formations as well as prevailing presence of growth faults had been identified as the main factors responsible for overpressure generation and preservation in the Niger Delta basin. Analysis of porosity dependent parameters such as interval transit times and interval velocities derived from the seismic records of a field in the Western Niger Delta revealed the presence of overpressured formation at depth of 8670 feet, which is the top of the overpressured zone. The plot of interval transit times against depth gave a positive deflection from normal at the region of overpressure while interval velocity plot gave negative deflection; the ratio of this deviation in both cases is as high as 1.52. Pressure gradient in the upper, normally pressured part of the field was determined to be 0.465 psi/ft., which is within the established normal pressure gradient range in Niger Delta, while the abnormal formation pressure gradient in the overpressured region was determined to be 0.96 psi/ft., and this is also within the published abnormal pressure gradient range of 0.71 to 1.1 psi/ft. in Niger Delta. Formation fracture pressure gradients were determined from the formation pressure information to be 0.66psi/ft. in the upper part of the field and 1.2psi/ft. in the overpressured horizon. Mud weight window (MWW); mud density range necessary to prevent formation kick without initiating hydraulic fracturing was determined to be 10.2 to 12.5lbm/gal in the upper part of the field and 22.1 to 22.63lbm/gal in the overpressured horizon. MWW is indispensable for the selection of the mud pump type, capacity, pumping rate and mud densities at different formation pressure regimes. Overpressure prediction is also requisite for drilling program design, casing design as well as rig capacity choice before spudding. It is necessary to reduce well construction risk, save drilling hour as well as cut down drilling cost. If adequate predictions are not taken however, drilling hazards known as blowout may occur. Blowout, an uncontrollable flow of formation fluid into the well has made oil exploration and exploitation activities in Niger Delta, Southern Nigeria, a curse for the people rather than a blessing because considerable numbers of wells blew out during well construction activities, hence the characteristic oil spill which had degraded the environment, making fishing operation, a source of livelihood of the people difficult. Therefore the need for overpressure prediction as a guide for safe drilling, especially in unfamiliar exploration environments.

Guides emerge for cementing horizontal strings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parcevaux, P.

1987-10-19

This article recommends the following guidelines for cementing of horizontal strings: turbulent flow displacement technique for ensuring vest casing centralization and a cement slurry with a density as close as possible to that of the drilling mud.

Diplomacy Through Earth Sciences: An Overview of US Geological Survey Technical Assistance Regarding the Ongoing LUSI Mud Eruption, East Java, Indonesia

NASA Astrophysics Data System (ADS)

Casadevall, T. J.

2009-12-01

In June 2007, the US Department of State (DOS) requested assistance from the USGS to provide technical guidance and advice to the US Mission in Indonesia regarding the Lumpur Sidoarjo (LUSI) mud crisis. In May 2006, LUSI began as a mud eruption from a series of mud springs adjacent to an oil and gas exploration well being drilled near Surabaya, East Java, Indonesia. The production of mud and waters from the LUSI crater area has now continued for more than 3 years with no significant change in mud production rate (~110,000 cubic meters per day) nor in temperature of the mud (70-80 degrees C). Engineers suggest that mud production will continue at these rates for years to decades to come. Regardless of future activity at LUSI, the current mud accumulation of more than 100 million cubic meters poses a physical and environmental hazard which requires continuous monitoring and observation. The first response to the 2007 DOS request involved a site visit to Indonesia in September 2007. The result of that visit was to recommend to the Government of Indonesia (GOI) that they focus on long-term management of the mud rather than focus on the controversy as to the cause of the eruption or the debate about stopping the flow. Other recommendations from the initial 2007 technical visit included contracting for a US scientist to be co-located with engineers of the Sidoarjo Mud Management Board (BPLS) in Surabaya, East Java, to advise and consult on day-to-day developments at the site of the mud eruption. A second technical team visit by USGS scientists and an engineer from the US Army Corps of Engineers in October-November 2008 made additional recommendations on the long-term management of the mud and was followed in December by the start of a 6 month contract for the US mud adviser. From the start of activity in mid-2006 through late-2008, there was a clear sense of urgency at the US Mission in Indonesia to provide guidance and advice and included the personal intervention of the new US Ambassador. The USGS has completed the requests made in the June 2007 DOS cable, including an initial characterization of the mud and fluids; an analysis of land surface changes using the INSAR method; and an assessment of the seismic hazards in East Java. In the coming year, USGS will assist DOI agencies in the geophysical monitoring of the LUSI area and in the continued characterization of mud and fluids produced by the eruption.

Borehole Stability in High-Temperature Formations

NASA Astrophysics Data System (ADS)

Yan, Chuanliang; Deng, Jingen; Yu, Baohua; Li, Wenliang; Chen, Zijian; Hu, Lianbo; Li, Yang

2014-11-01

In oil and gas drilling or geothermal well drilling, the temperature difference between the drilling fluid and formation will lead to an apparent temperature change around the borehole, which will influence the stress state around the borehole and tend to cause borehole instability in high geothermal gradient formations. The thermal effect is usually not considered as a factor in most of the conventional borehole stability models. In this research, in order to solve the borehole instability in high-temperature formations, a calculation model of the temperature field around the borehole during drilling is established. The effects of drilling fluid circulation, drilling fluid density, and mud displacement on the temperature field are analyzed. Besides these effects, the effect of temperature change on the stress around the borehole is analyzed based on thermoelasticity theory. In addition, the relationships between temperature and strength of four types of rocks are respectively established based on experimental results, and thermal expansion coefficients are also tested. On this basis, a borehole stability model is established considering thermal effects and the effect of temperature change on borehole stability is also analyzed. The results show that the fracture pressure and collapse pressure will both increase as the temperature of borehole rises, and vice versa. The fracture pressure is more sensitive to temperature. Temperature has different effects on collapse pressures due to different lithological characters; however, the variation of fracture pressure is unrelated to lithology. The research results can provide a reference for the design of drilling fluid density in high-temperature wells.

Ultra-Deep Drilling Cost Reduction; Design and Fabrication of an Ultra-Deep Drilling Simulator (UDS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lindstrom, Jason

2010-01-31

Ultra-deep drilling, below about 20,000 ft (6,096 m), is extremely expensive and limits the recovery of hydrocarbons at these depths. Unfortunately, rock breakage and cuttings removal under these conditions is not understood. To better understand and thus reduce cost at these conditions an ultra-deep single cutter drilling simulator (UDS) capable of drill cutter and mud tests to sustained pressure and temperature of 30,000 psi (207 MPa) and 482 °F (250 °C), respectively, was designed and manufactured at TerraTek, a Schlumberger company, in cooperation with the Department of Energy’s National Energy Technology Laboratory. UDS testing under ultra-deep drilling conditions offers anmore » economical alternative to high day rates and can prove or disprove the viability of a particular drilling technique or fluid to provide opportunity for future domestic energy needs.« less

A field trial for an ex-situ bioremediation of a drilling mud-polluted site.

PubMed

Rojas-Avelizapa, N G; Roldán-Carrillo, T; Zegarra-Martínez, H; Muñoz-Colunga, A M; Fernández-Linares, L C

2007-01-01

The remediation of drilling mud-polluted sites in the Southeast of Mexico is a top priority for Mexican oil industry. The objective of this work was to find a technology to remediate these sites. A field trial was performed by composting in biopiles, where four 1ton soil-biopiles were established, one treatment in triplicate and one unamended biopile. Amended biopiles were added with nutrients to get a C/N/P ratio of 100/3/0.5 plus a bulking agent (straw) at a soil/straw ratio of 97/3. Moisture content was maintained around 30-35%. Results showed that, after 180 d, total petroleum hydrocarbon (TPH) concentrations decreased from 99300+/-23000mgTPHkg(-1) soil to 5500+/-770mgTPHkg(-1) for amended biopiles and to 22900+/-7800mgTPHkg(-1) for unamended biopile. An undisturbed soil control showed no change in TPH concentrations. Gas chromatographic analysis showed residual alkyl dibenzothiophene type compounds. Highest bacterial counts were observed during the first 30 d which correlated with highest TPH removal, whereas fungal count increased at the end of the experimentation period. Results suggested an important role of the straw, nutrient addition and water content in stimulating aerobic microbial activity and thus hydrocarbon removal. This finding opens an opportunity to remediate old polluted sites with recalcitrant and high TPH concentration.

Time Dependent Fluids

ERIC Educational Resources Information Center

Collyer, A. A.

1974-01-01

Discusses the flow characteristics of thixotropic and negative thixotropic fluids; various theories underlying the thixotropic behavior; and thixotropic phenomena exhibited in drilling muds, commercial paints, pastes, and greases. Inconsistencies in the terminology used to label time dependent effects are revealed. (CC)

Geopressured well project Sweet Lake, Cameron Parish, Louisiana. Final report Feb 80-Sep 82

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, K.S.

1983-01-01

The Sweet Lake geopressured-geothermal test well(Magma Gulf-Technadril/DOE Amoco Fee 1) was drilled in Cameron Parish, Louisiana under a Department of Energy contract. The primary purpose was to demonstrate technological and economic recovery of the geopressured-geothermal resource. The Gas Research Institute funded ancillary work in mud logging, micropaleontology, organic geochemistry, rock mechanics, and core analysis. The well was perforated in the upper Frio Miogypsinoides sand, at a depth of 15,387-15,414 feet. Mud logging and micropaleontology were used to monitor stratigraphic position during the drilling of the well and were particularly important in picking the casing point at the top of themore » Miogypsinoides sand. Several phases of testing have been carried out, including an initial flow test, a reservoir limit test, and long-term (6+ month) testing.« less

KIGAM Seafloor Observation System (KISOS) for the baseline study in monitoring of gas hydrate test production in the Ulleung Basin, Korea

NASA Astrophysics Data System (ADS)

Lee, Sung-rock; Chun, Jong-hwa

2013-04-01

For the baseline study in the monitoring gas hydrate test production in the Ulleung Basin, Korea Institute of Geoscience and Mineral Resources (KIGAM) has developed the KIGAM Seafloor Observation System (KISOS) for seafloor exploration using unmanned remotely operated vehicle connected with a ship by a cable. The KISOS consists of a transponder of an acoustic positioning system (USBL), a bottom finding pinger, still camera, video camera, water sampler, and measuring devices (methane, oxygen, CTD, and turbidity sensors) mounted on the unmanned ROV, and a sediment collecting device collecting sediment on the seafloor. It is very important to monitoring the environmental risks (gas leakage and production water/drilling mud discharge) which may be occurred during the gas hydrate test production drilling. The KISOS will be applied to solely conduct baseline study with the KIGAM seafloor monitoring system (KIMOS) of the Korean gas hydrate program in the future. The large scale of environmental monitoring program includes the environmental impact assessment such as seafloor disturbance and subsidence, detection of methane gas leakage around well and cold seep, methane bubbles and dissolved methane, change of marine environments, chemical factor variation of water column and seabed, diffusion of drilling mud and production water, and biological factors of biodiversity and marine habitats before and after drilling test well and nearby areas. The design of the baseline survey will be determined based on the result of SIMAP simulation in 2013. The baseline survey will be performed to provide the gas leakage and production water/drilling mud discharge before and after gas hydrate test production. The field data of the baseline study will be evaluated by the simulation and verification of SIMAP simulator in 2014. In the presentation, the authors would like introduce the configuration of KISOS and applicability to the seafloor observation for the gas hydrate test production in the Ulleung Basin. This work was financially supported by the the Ministry of Knowledge Economy(MKE) and Gas Hydrate R/D Organization(GHDO)

46 CFR 108.173 - Class I, Division 2 locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... locations. The following are Class I, Division 2 locations: (a) An enclosed space that has any open portion... mud pit. (b) A location in the weather that is— (1) Within the boundaries of the drilling derrick up...

Looking For a Needle in the Haystack: Deciphering Indigenous 1.79 km Deep Subsurface Microbial Communities from Drilling Mud Contaminants Using 454 Pyrotag Sequencing

NASA Astrophysics Data System (ADS)

Dong, Y.; Cann, I.; Mackie, R.; Price, N.; Flynn, T. M.; Sanford, R.; Miller, P.; Chia, N.; Kumar, C. G.; Kim, P.; Sivaguru, M.; Fouke, B. W.

2010-12-01

Knowledge of the composition, structure and activity of microbial communities that live in deeply buried sedimentary rocks is fundamental to the future of subsurface biosphere stewardship as it relates to hydrocarbon exploration and extraction, carbon sequestration, gas storage and groundwater management. However, the study of indigenous subsurface microorganisms has been limited by the technical challenges of collecting deep formation water samples that have not been heavily contaminated by the mud used to drill the wells. To address this issue, a “clean-sampling method” deploying the newly developed Schlumberger Quicksilver MDT probe was used to collect a subsurface sample at a depth of 1.79 km (5872 ft) from an exploratory well within Cambrian-age sandstones in the Illinois Basin. This yielded a formation water sample that was determined to have less than 4% drilling mud contamination based on tracking changes in the aqueous geochemistry of the formation water during ~3 hours of pumping at depth prior to sample collection. A suite of microscopy and culture-independent molecular analyses were completed using the DNA extracted from microbial cells in the formation water, which included 454 amplicon pyrosequencing that targeted the V1-V3 hypervariable region of bacterial 16S rRNA gene sequences. Results demonstrated an extremely low diversity microbial community living in formation water at 1.79 km-depth. More than 95 % of the total V1-V3 pyrosequencing reads (n=11574) obtained from the formation water were affiliated with a halophilic γ-proteobacterium and most closely related to the genus Halomonas. In contrast, about 3 % of the V1-V3 sequences in the drilling mud library (n=13044) were classified as genus Halomonas but were distinctly different and distantly related to the formation water Halomonas detected at 1.79 km-depth. These results were consistent with those obtained using a suite of other molecular screens (e.g., Terminal-Restriction Fragment Length Polymorphism (T-RFLP) and the initial full length 16S rRNA amplicon libraries) and bioinformatic analyses (e.g., 16S rRNA and Open Reading Frame (ORF) calls established from the 454 metagenomic community analyses). Functional pathway modeling is underway to evaluate the adaptation of this indigenous microbial community to the hydrologic and geologic history of the deep subsurface environment of the Illinois Basin.

Application of Rosenbrock search technique to reduce the drilling cost of a well in Bai-Hassan oil field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aswad, Z.A.R.; Al-Hadad, S.M.S.

1983-03-01

The powerful Rosenbrock search technique, which optimizes both the search directions using the Gram-Schmidt procedure and the step size using the Fibonacci line search method, has been used to optimize the drilling program of an oil well drilled in Bai-Hassan oil field in Kirkuk, Iran, using the twodimensional drilling model of Galle and Woods. This model shows the effect of the two major controllable variables, weight on bit and rotary speed, on the drilling rate, while considering other controllable variables such as the mud properties, hydrostatic pressure, hydraulic design, and bit selection. The effect of tooth dullness on the drillingmore » rate is also considered. Increasing the weight on the drill bit with a small increase or decrease in ratary speed resulted in a significant decrease in the drilling cost for most bit runs. It was found that a 48% reduction in this cost and a 97-hour savings in the total drilling time was possible under certain conditions.« less

Key Technologies and Applications of Gas Drainage in Underground Coal Mine

NASA Astrophysics Data System (ADS)

Zhou, Bo; Xue, Sheng; Cheng, Jiansheng; Li, Wenquan; Xiao, Jiaping

2018-02-01

It is the basis for the long-drilling directional drilling, precise control of the drilling trajectory and ensuring the effective extension of the drilling trajectory in the target layer. The technology can be used to complete the multi-branch hole construction and increase the effective extraction distance of the coal seam. The gas drainage and the bottom grouting reinforcement in the advanced area are realized, and the geological structure of the coal seam can be proved accurately. It is the main technical scheme for the efficient drainage of gas at home and abroad, and it is applied to the field of geological structure exploration and water exploration and other areas. At present, the data transmission method is relatively mature in the technology and application, including the mud pulse and the electromagnetic wave. Compared with the mud pulse transmission mode, the electromagnetic wave transmission mode has obvious potential in the data transmission rate and drilling fluid, and it is suitable for the coal mine. In this paper, the key technologies of the electromagnetic wave transmission mode are analyzed, including the attenuation characteristics of the electromagnetic transmission channel, the digital modulation scheme, the channel coding method and the weak signal processing technology. A coal mine under the electromagnetic wave drilling prototype is developed, and the ground transmission experiments and down hole transmission test are carried out. The main work includes the following aspects. First, the equivalent transmission line method is used to establish the electromagnetic transmission channel model of coal mine drilling while drilling, and the attenuation of the electromagnetic signal is measured when the electromagnetic channel measured. Second, the coal mine EM-MWD digital modulation method is developed. Third, the optimal linear block code which suitable for EM-MWD communication channel in coal mine is proposed. Fourth, the noise characteristics of well near horizontal directional drilling are analyzed, and the multi-stage filter method is proposed to suppress the natural potential and strong frequency interference signal. And the weak electromagnetic communication signal is extracted from the received signal. Finally, the detailed design of the electromagnetic wave while drilling is given.

Prediction of magnitude of minimum horizontal stress from extended leak-off test conducted by the riser vessel CHIKYU

NASA Astrophysics Data System (ADS)

Lin, W.; Masago, H.; Yamamoto, K.; Kawamura, Y.; Saito, S.; Kinoshita, M.

2007-12-01

By means of introduction of the drilling vessel 'CHIKYU', riser drilling operations using mud fluid will be carried out in NanTroSEIZE Stage 2 for the first time as an oceanic scientific-drilling. For determining drilling operation parameter such as a mud density, a downhole experiment, leak-off test (LOT) or extended leak-off test (XLOT), is going to be implemented next to casing and cementing at each casing shoe during the drilling process. Data of the downhole experiment aimed for operation can also be used for an important scientific application to obtain in-situ stress information which is necessary for various cases of scientific drillings such as seismogenic zone drillings etc. In order to examine feasibility of the application of the LOT or XLOT data, we analyzed an example of XLOT conducted by the riser vessel CHIKYU during its Shimokita shakedown cruise, 2006; and then estimated magnitude of minimum principal stress in horizontal plane, Shmin. Moreover, we will propose the test procedures to possibly improve the quality of stress result from the applications of LOT or XLOT. The XLOT of Shimokita cruise was conducted under following conditions; 1180 m water depth, 525 mbsf (meter below seafloor) depth, 1030 kg/m3 fluid density (seawater) and 80 litter/min injection flow-rate. Estimated magnitude of the Shmin is equal to 18.3 MPa based on the assumption that fracture closure pressure balances with the minimum principal stress perpendicular to the fracture plane. For comparison, the vertical stress magnitude at the depth was estimated from density profile of core samples retrieved from the same borehole; and was equal to 20 MPa approximately. These two values can be considered to be not disagreement. Therefore, we can say that the XLOT data is valuable and practical for estimating the magnitude of minimum horizontal stress. From the viewpoint of determining stress magnitude, the XLOT is more essential rather than the LOT because it might be hardly to obtain reliable Shmin magnitude only by leak-off pressure which is exclusive stress-related parameter obtained from the latter. In addition, implementation of the LOT/XLOT multi-cycles (3 cycles) is preferable if possible. The first cycle with a lower maximum injection pressure is for knowing permeable property of the formation and for examining whether there is pre-existing fracture(s). The second cycle is a normal XLOT; and the third one is the repeat of the second one for confirm the pressure values obtained from the XLOTs.

Short-term Influence of Drilling Fluid on Ciliates from Activated Sludge in Sequencing Batch Reactors.

PubMed

Babko, Roman; Kuzmina, Tatiana; Łagód, Grzegorz; Jaromin-Gleń, Katarzyna; Danko, Yaroslav; Pawłowska, Małgorzata; Pawłowski, Artur

2017-01-01

Spent drilling muds are the liquid residues of rock drilling operations. Due to a high concentration of suspended solids and potentially detrimental chemical properties, they can negatively affect microorganisms participating in wastewater treatment processes. We evaluated the addition of a potassium-polymer drilling fluid (DF) to activated sludge in laboratory sequencing batch reactors (SBRs) for municipal wastewater treatment. Ciliate assemblage, the most dynamic component of eukaryotes in activated sludge, and which is highly sensitive to changes in the system, was evaluated. The average ciliate abundance dropped by about 51% (SBR 2; 1% DF added) and 33% (SBR 3; 3% DF added) in comparison to the control (SBR 1; wastewater only). A decrease in the total number of ciliate species during the experiment was observed, from 25 to 24 in SBR 2 and from 17 to 13 in SBR 3. Moreover, a drop in the number of dominant (>100 individuals mL) ciliate species was observed during the experiment-from eight in the control to five in SBR 2 and four in SBR 3-signaling noticeable changes in the quantitative structure of ciliate species. The species analyzed showed different responses to DF addition. The most sensitive was , which is bacteriovorus. In contrast, two predators, and , showed no reaction to DF addition. Our results indicate that addition of potassium-polymer DF, in doses of 1 to 3% of the treated wastewater volume, had no toxic effects on ciliates, but qualitative and quantitative changes in their community were observed. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khin, J.A.

Since reopening to foreign operators in 1989, companies have secured concessions and begun active exploration programs. This paper reports on: Yukong Oil (Block C) spudded well Indaw YK-1 last December and continued drilling below 8,500 ft. Well encountered frequent gas cut mud as well as lost circulation. BHP (Block H) spudded the Kawliya-1 in March this year and drilled to 6,500 ft. The well was dry and abandoned BHP plans to drill another well this year. Unocal (Block F) spudded its first well, the Kandaw-1, in May and plans to drill to 14,500 ft. Shell (Block G) began its firstmore » well in June. Shell's drilling program will consist of drilling four to six wells. Idemitsu (Block D) also spudded its first well in June. PetroCanada (Block E) plans to spud a well by December. Target depth is 12,000 ft.« less

The installation of a sub sea floor observatory using the sea floor drill rig MeBo

NASA Astrophysics Data System (ADS)

Wefer, G.; Freudenthal, T.; Kopf, A.

2012-04-01

Sea floor drill rigs that can be deployed from standard research vessels are bridging the gap between dedicated drill ships that are used for deep drillings in the range of several hundred meters below sea floor and conventional sampling tools like gravity corers, piston corer or dredges that only scratch the surface of the sea floor. A major advantage of such robotic drill rigs is that the drilling action is conducted from a stable platform at the sea bed independent of any ship movements due to waves, wind or currents. At the MARUM Center for Marine Environmental Sciences at the University of Bremen we developed the sea bed drill rig MeBo that can be deployed from standard research vessels. The drill rig is deployed on the sea floor and controlled from the vessel. Drilling tools for coring the sea floor down to 70 m can be stored on two magazines on the rig. A steel-armoured umbilical is used for lowering the rig to the sea bed in water depths up to 2000 m in the present system configuration. It was successfully operated on ten expeditions since 2005 and drilled more than 1000 m in different types of geology including hemipelagic mud, glacial till as well as sedimentary and crystalline rocks. MeBo boreholes be equipped with sensors and used for long term monitoring are planned. Depending on the scientific demands, a MeBoCORK monitoring system will allow in situ measurements of eg. temperature and pressure. The "MeBoCORK" will be equipped with data loggers and data transmission interface for reading out the collected data from the vessel. By additional payload installation on the MeBoCORK with an ROV it will be possible to increase the energy capacity as well as to conduct fluid sampling in the bore hole for geochemical analyses. It is planned to install a prototype of this additional payload with the MARUM ROV QUEST4000M during the following R/V SONNE cruise in July 2012.

Effects of size on three-cone bit performance in laboratory drilled shale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Black, A.D.; DiBona, B.G.; Sandstrom, J.L.

1982-09-01

The effects of size on the performance of 3-cone bits were measured during laboratory drilling tests in shale at simulated downhole conditions. Four Reed HP-SM 3-cone bits with diameters of 6 1/2, 7 7/8, 9 1/2 and 11 inches were used to drill Mancos shale with water-based mud. The tests were conducted at constant borehole pressure, two conditions of hydraulic horsepower per square inch of bit area, three conditions of rotary speed and four conditions of weight-on-bit per inch of bit diameter. The resulting penetration rates and torques were measured. Statistical techniques were used to analyze the data.

Transesterification reaction for synthesis of palm-based ethylhexyl ester and formulation as base oil for synthetic drilling fluid.

PubMed

Abdul Habib, Nor Saiful Hafiz; Yunus, Robiah; Rashid, Umer; Taufiq-Yap, Yun H; Abidin, Zurina Zainal; Syam, Azhari Muhammad; Irawan, Sonny

2014-01-01

The use of vegetable oil-based ester as a base fluid in synthetic drilling fluid has become a trend in drilling operations due to its environmental advantages. The transesterification reaction of palm oil methyl ester (POME) with 2-ethylhexanol (2EH) produced 98% of palm oil-based ethylhexyl ester in less than 30 minutes. Since the transesterification reaction of POME with 2EH is a reversible reaction, its kinetics was studied in the presence of excess EH and under vacuum. The POME-to-EH molar ratio and vacuum pressure were held constant at 1:2 and 1.5 mbar respectively and the effects of temperature (70 to 110°C) were investigated. Using excess of EH and continual withdrawal of methanol via vacuum promoted the reaction to complete in less than 10 minutes. The rate constant of the reaction (k) obtained from the kinetics study was in the range of 0.44 to 0.66 s⁻¹ and the activation energy was 15.6 kJ.mol⁻¹. The preliminary investigations on the lubrication properties of drilling mud formulated with palm oil-based 2EH ester indicated that the base oil has a great potential to substitute the synthetic ester-based oil for drilling fluid. Its high kinematic viscosity provides better lubrication to the drilling fluid compared to other ester-based oils. The pour point (-15°C) and flash point (204°C) values are superior for the drilling fluid formulation. The plastic viscosity, HPHT filtrate loss and emulsion stability of the drilling fluid had given acceptable values, while gel strength and yield point could be improved by blending it with proper additives.

Log evaluation in wells drilled with inverted oil emulsion mud. [GLOBAL program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, D.P.; Lacour-Gayet, P.J.; Suau, J.

1981-01-01

As greater use is made of inverted oil emulsion, muds in the development of North Sea oil fields, the need for more precise log evaluation in this environment becomes apparent. This paper demonstrates an approach using the Dual Induction Log, taking into account invasion and boundary effects. Lithology and porosity are derived from the Formation Density or Litho-Density Log, Compensated Neutron Log, Sonic Log and the Natural Gamma Ray Spectrometry log. The effect of invasion by the oil component of the mud filtrate is treated in the evaluation, and a measurement of Moved Water is made Computations of petrophysical propertiesmore » are implemented by means of the GLOBAL interpretation program, taking advantage of its capability of adaption to any combination of logging sensors. 8 refs.« less

Application of drilling, coring, and sampling techniques to test holes and wells

USGS Publications Warehouse

Shuter, Eugene; Teasdale, Warren E.

1989-01-01

The purpose of this manual is to provide ground-water hydrologists with a working knowledge of the techniques of test drilling, auger drilling, coring and sampling, and the related drilling and sampling equipment. For the most part, the techniques discussed deal with drilling, sampling, and completion of test holes in unconsolidated sediments because a hydrologist is interested primarily in shallow-aquifer data in this type of lithology. Successful drilling and coring of these materials usually is difficult, and published research information on the subject is not readily available. The authors emphasize in-situ sampling of unconsolidated sediments to obtain virtually undisturbed samples. Particular attention is given to auger drilling and hydraulic-rotary methods of drilling because these are the principal means of test drilling performed by the U.S. Geological Survey during hydrologic studies. Techniques for sampling areas contaminated by solid or liquid waste are discussed. Basic concepts of well development and a detailed discussion of drilling muds, as related to hole conditioning, also are included in the report. The information contained in this manual is intended to help ground-water hydrologists obtain useful subsurface data and samples from their drilling programs.

Deep-biosphere methane production stimulated by geofluids in the Nankai accretionary complex

PubMed Central

Kubo, Yusuke; Hoshino, Tatsuhiko; Sakai, Sanae; Arnold, Gail L.; Case, David H.; Lever, Mark A.; Morita, Sumito; Nakamura, Ko-ichi

2018-01-01

Microbial life inhabiting subseafloor sediments plays an important role in Earth’s carbon cycle. However, the impact of geodynamic processes on the distributions and carbon-cycling activities of subseafloor life remains poorly constrained. We explore a submarine mud volcano of the Nankai accretionary complex by drilling down to 200 m below the summit. Stable isotopic compositions of water and carbon compounds, including clumped methane isotopologues, suggest that ~90% of methane is microbially produced at 16° to 30°C and 300 to 900 m below seafloor, corresponding to the basin bottom, where fluids in the accretionary prism are supplied via megasplay faults. Radiotracer experiments showed that relatively small microbial populations in deep mud volcano sediments (102 to 103 cells cm−3) include highly active hydrogenotrophic methanogens and acetogens. Our findings indicate that subduction-associated fluid migration has stimulated microbial activity in the mud reservoir and that mud volcanoes may contribute more substantially to the methane budget than previously estimated. PMID:29928689

30 CFR 250.300 - Pollution prevention.

Code of Federal Regulations, 2012 CFR

2012-07-01

... environment. No petroleum-based substances, including diesel fuel, may be added to the drilling mud system... Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL... oil and gas or sulphur, the lessee shall take measures to prevent unauthorized discharge of pollutants...

30 CFR 250.300 - Pollution prevention.

Code of Federal Regulations, 2013 CFR

2013-07-01

... environment. No petroleum-based substances, including diesel fuel, may be added to the drilling mud system... Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL... oil and gas or sulphur, the lessee shall take measures to prevent unauthorized discharge of pollutants...

30 CFR 250.300 - Pollution prevention.

Code of Federal Regulations, 2014 CFR

2014-07-01

... environment. No petroleum-based substances, including diesel fuel, may be added to the drilling mud system... Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL... oil and gas or sulphur, the lessee shall take measures to prevent unauthorized discharge of pollutants...

New LWD tools are just in time to probe for baby elephants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghiselin, D.

Development of sophisticated formation evaluation instrumentation for use while drilling has led to a stratification of while-drilling services. Measurements while drilling (MWD) comprises measurements of mechanical parameters like weight-on-bit, mud pressures, torque, vibration, hole angle and direction. Logging while drilling (LWD) describes resistivity, sonic, and radiation logging which rival wireline measurements in accuracy. A critical feature of LWD is the rate that data can be telemetered to the surface. Early tools could only transmit 3 bits per second one way. In the last decade, the data rate has more than tripled. Despite these improvements, LWD tools have the ability tomore » make many more measurements than can be telemetered in real-time. The paper discusses the development of this technology and its applications.« less

Measurement system analysis of viscometers used for drilling mud characterization

NASA Astrophysics Data System (ADS)

Mat-Shayuti, M. S.; Adzhar, S. N.

2017-07-01

Viscometers in the Faculty of Chemical Engineering, University Teknologi MARA, are subject to heavy utilization from the members of the faculty. Due to doubts surrounding their result integrity and maintenance management, Measurement System Analysis was executed. 5 samples of drilling muds with varied barite content from 5 - 25 weight% were prepared and their rheological properties determined in 3 trials by 3 operators using the viscometers. Gage Linearity and Bias Study were performed using Minitab software and the result shows high biases in the range of 19.2% to 38.7%, with non-linear trend along the span of measurements. Gage Repeatability & Reproducibility (Nested) analysis later produces Percent Repeatability & Reproducibility more than 7.7% and Percent Tolerance above 30%. Lastly, good and marginal Distinct Categories output are seen among the results. Despite acceptable performance of the measurement system in Distinct Categories, the poor results in accuracy, linearity, and Percent Repeatability & Reproducibility render the gage generally not capable. Improvement to the measurement system is imminent.

Developing monitoring plans to detect spills related to natural gas production.

PubMed

Harris, Aubrey E; Hopkinson, Leslie; Soeder, Daniel J

2016-11-01

Surface water is at risk from Marcellus Shale operations because of chemical storage on drill pads during hydraulic fracturing operations, and the return of water high in total dissolved solids (up to 345 g/L) from shale gas production. This research evaluated how two commercial, off-the-shelf water quality sensors responded to simulated surface water pollution events associated with Marcellus Shale development. First, peak concentrations of contaminants from typical spill events in monitored watersheds were estimated using regression techniques. Laboratory measurements were then conducted to determine how standard in-stream instrumentation that monitor conductivity, pH, temperature, and dissolved oxygen responded to three potential spill materials: ethylene glycol (corrosion inhibitor), drilling mud, and produced water. Solutions ranging from 0 to 50 ppm of each spill material were assessed. Over this range, the specific conductivity increased on average by 19.9, 27.9, and 70 μS/cm for drilling mud, ethylene glycol, and produced water, respectively. On average, minor changes in pH (0.5-0.8) and dissolved oxygen (0.13-0.23 ppm) were observed. While continuous monitoring may be part of the strategy for detecting spills to surface water, these minor impacts to water quality highlight the difficulty in detecting spill events. When practical, sensors should be placed at the mouths of small watersheds where drilling activities or spill risks are present, as contaminant travel distance strongly affects concentrations in surface water systems.

Environment-friendly drilling operation technology

NASA Astrophysics Data System (ADS)

Luo, Huaidong; Jing, Ning; Zhang, Yanna; Huang, Hongjun; Wei, Jun

2017-01-01

Under the circumstance that international safety and environmental standards being more and more stringent, drilling engineering is facing unprecedented challenges, the extensive traditional process flow is no longer accepted, the new safe and environment-friendly process is more suitable to the healthy development of the industry. In 2015, CNPCIC adopted environment-friendly drilling technology for the first time in the Chad region, ensured the safety of well control, at the same time increased the environmental protection measure, reduced the risk of environmental pollution what obtain the ratification from local government. This technology carries out recovery and disposal of crude oil, cuttings and mud without falling on the ground. The final products are used in road and well site construction, which realizes the reutilization of drilling waste, reduces the operating cost, and provides a strong technical support for cost-cutting and performance-increase of drilling engineering under low oil price.

Chemical and biological assessment of two offshore drilling sites in the Alaskan Arctic.

PubMed

Trefry, John H; Dunton, Kenneth H; Trocine, Robert P; Schonberg, Susan V; McTigue, Nathan D; Hersh, Eric S; McDonald, Thomas J

2013-05-01

A retrospective chemical and biological study was carried out in Camden Bay, Alaskan Beaufort Sea, where single exploratory oil wells were drilled at two sites more than two decades ago. Barium from discharged drilling mud was present in sediments at concentrations as high as 14%, ~200 times above background, with significantly higher concentrations of Ba, but not other metals, within 250 m of the drilling site versus reference stations. Elevated concentrations of Cr, Cu, Hg and Pb were found only at two stations within 25 m of one drilling site. Concentrations of total polycyclic aromatic hydrocarbons (TPAH) were not significantly different at reference versus drilling-site stations; however, TPAH were elevated in Ba-rich layers from naturally occurring perylene in ancient formation cuttings. Infaunal biomass and species abundance were not significantly different at reference versus drilling-site stations; infauna were less diverse at drilling-site stations. Our assessment showed that discharges from single wells within large areas caused minimal long-term, adverse impacts to the benthic ecosystem. Copyright © 2013 Elsevier Ltd. All rights reserved.

Numerical Simulations of Thermo-Mechanical Processes during Thermal Spallation Drilling for Geothermal Reservoirs

NASA Astrophysics Data System (ADS)

Vogler, D.; Walsh, S. D. C.; Rudolf von Rohr, P.; Saar, M. O.

2017-12-01

Drilling expenses constitute a significant share of the upfront capital costs and thereby the associated risks of geothermal energy production. This is especially true for deep boreholes, as drilling costs per meter increase significantly with depth. Thermal spallation drilling is a relatively new drilling technique, particularly suited to the hard crystalline (e.g., basement) rocks in which many deep geothermal resources are located. The method uses a hot jet-flame to rapidly heat the rock surface, which leads to large temperature gradients in the rock. These temperature gradients cause localized thermal stresses that, in combination with the in situ stress field, lead to the formation and ejection of spalls. These spalls are then transported out of the borehole with the drilling mud. Thermal spallation not only in principle enables much faster rates of penetration than traditional rotary drilling, but is also contact-less, which significantly reduces the long tripping times associated with conventional rotary head drilling. We present numerical simulations investigating the influence of rock heterogeneities on the thermal spallation process. Special emphasis is put on different mineral compositions, stress regimes, and heat sources.

The mechanics and physics of fracturing: application to thermal aspects of crack propagation and to fracking.

PubMed

Cherepanov, Genady P

2015-03-28

By way of introduction, the general invariant integral (GI) based on the energy conservation law is presented, with mention of cosmic, gravitational, mass, elastic, thermal and electromagnetic energy of matter application to demonstrate the approach, including Coulomb's Law generalized for moving electric charges, Newton's Law generalized for coupled gravitational/cosmic field, the new Archimedes' Law accounting for gravitational and surface energy, and others. Then using this approach the temperature track behind a moving crack is found, and the coupling of elastic and thermal energies is set up in fracturing. For porous materials saturated with a fluid or gas, the notion of binary continuum is used to introduce the corresponding GIs. As applied to the horizontal drilling and fracturing of boreholes, the field of pressure and flow rate as well as the fluid output from both a horizontal borehole and a fracture are derived in the fluid extraction regime. The theory of fracking in shale gas reservoirs is suggested for three basic regimes of the drill mud permeation, with calculating the shape and volume of the local region of the multiply fractured rock in terms of the pressures of rock, drill mud and shale gas. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Geopressure modeling from petrophysical data: An example from East Kalimantan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herkommer, M.A.

1994-07-01

Localized models of abnormal formation pressure (geopressure) are important economic and safety tools frequently used for well planning and drilling operations. Simplified computer-based procedures have been developed that permit these models to be developed more rapidly and with greater accuracy. These techniques are broadly applicable to basins throughout the world where abnormal formation pressures occur. An example from the Attaka field of East Kalimantan, southeast Asia, shows how geopressure models are developed. Using petrophysical and engineering data, empirical correlations between observed pressure and petrophysical logs can be created by computer-assisted data-fitting techniques. These correlations serve as the basis for modelsmore » of the geopressure. By performing repeated analyses on wells at various locations, contour maps on the top of abnormal geopressure can be created. Methods that are simple in their development and application make the task of geopressure estimation less formidable to the geologist and petroleum engineer. Further, more accurate estimates can significantly improve drilling speeds while reducing the incidence of stuck pipe, kicks, and blowouts. In general, geopressure estimates are used in all phases of drilling operations: To develop mud plans and specify equipment ratings, to assist in the recognition of geopressured formations and determination of mud weights, and to improve predictions at offset locations and geologically comparable areas.« less

Habitat impacts of offshore drilling, eastern Gulf of Mexico

USGS Publications Warehouse

Shinn, Eugene A.; Lidz, Barbara H.; Reich, Christopher D.

1994-01-01

In this survey six offshore exploratory drill sites in a variety of environments and water depths were examined using a small research submersible. Sites varied from locations off northwest Florida to as far west as offshore Alabama. Water depths ranged from 21 m (70 ft) to 149 m (489 ft), and bottom sediments ranged from carbonate mud to Shelly quartz sand and silt to hard limestone. The age of the sites (the time between cessation of drilling activities and our observations) ranged from 15 months to 17 years . In a previous MMS-funded study, Shinn et al. (1989) and Dustan et al . (1991) examined eight sites off South Florida, where the age of the sites ranged from 2 to 29 years. The study documented repeatedly variability of impact from site to site . In the present study, we note a similar wide divergence of impacts . Using the concentration of barium (the major component of drill mud), cuttings, and trace metals as a basis, we found that time is the single most important factor determining the nature of habitat recovery. Older sites, particularly the 17-year-old site, were relatively pristine. At a 7-year-old site, two hurricanes did far more damage than drilling . At other sites, we documented a significant amount of discarded debris, and at two 5-year-old sites, large concentrations of barium and cuttings. Impacts, such as the extent of debris and cuttings, affected the bottom ranging in area from almost negligible (17-year-old site) to as much as 3 acres (4-year-old site) . As suspected, those sites with the most debris and/or open boreholes attracted the most abundant and diverse fish fauna.

Modeling of oil mist and oil vapor concentration in the shale shaker area on offshore drilling installations.

PubMed

Bråtveit, Magne; Steinsvåg, Kjersti; Lie, Stein Atle; Moen, Bente E

2009-11-01

The objective of this study was to develop regression models to predict concentrations of oil mist and oil vapor in the workplace atmosphere in the shale shaker area of offshore drilling installations. Collection of monitoring reports of oil mist and oil vapor in the mud handling areas of offshore drilling installations was done during visits to eight oil companies and five drilling contractors. A questionnaire was sent to the rig owners requesting information about technical design of the shaker area. Linear mixed-effects models were developed using concentration of oil mist or oil vapor measured by stationary sampling as dependent variables, drilling installation as random effect, and potential determinants related to process technical parameters and technical design of the shale shaker area as fixed effects. The dataset comprised stationary measurements of oil mist (n = 464) and oil vapor (n = 462) from the period 1998 to 2004. The arithmetic mean concentrations of oil mist and oil vapor were 3.89 mg/m(3) and 39.7 mg/m(3), respectively. The air concentration models including significant determinants such as viscosity of base oil, mud temperature, well section, type of rig, localization of shaker, mechanical air supply, air grids in outer wall, air curtain in front of shakers, and season explained 35% and 17% of the total variance in oil vapor and oil mist, respectively. The developed models could be used to indicate what impact differences in technical design and changes in process parameters have on air concentrations of oil mist and oil vapor. Thus, the models will be helpful in planning control measures to reduce the potential for occupational exposure.

Borehole data transmission apparatus

DOEpatents

Kotlyar, Oleg M.

1993-01-01

A borehole data transmission apparatus whereby a centrifugal pump impeller(s) is used to provide a turbine stage having substantial pressure characteristics in response to changing rotational speed of a shaft for the pressure pulsing of data from the borehole through the drilling mud to the surface of the earth.

Drilling informatics: data-driven challenges of scientific drilling

NASA Astrophysics Data System (ADS)

Yamada, Yasuhiro; Kyaw, Moe; Saito, Sanny

2017-04-01

The primary aim of scientific drilling is to precisely understand the dynamic nature of the Earth. This is the reason why we investigate the subsurface materials (rock and fluid including microbial community) existing under particular environmental conditions. This requires sample collection and analytical data production from the samples, and in-situ data measurement at boreholes. Current available data comes from cores, cuttings, mud logging, geophysical logging, and exploration geophysics, but these datasets are difficult to be integrated because of their different kinds and scales. Now we are producing more useful datasets to fill the gap between the exiting data and extracting more information from such datasets and finally integrating the information. In particular, drilling parameters are very useful datasets as geomechanical properties. We believe such approach, 'drilling informatics', would be the most appropriate to obtain the comprehensive and dynamic picture of our scientific target, such as the seismogenic fault zone and the Moho discontinuity surface. This presentation introduces our initiative and current achievements of drilling informatics.

Program for the improvement of downhole drilling motor bearings and seals. Phase V. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeLafosse, P.H.; Tibbitts, G.A.; Black, A.D.

1983-08-01

The work done during the fifth and final phase of a program to improve downhole drilling motor bearing and seals is described. The principal activities in this phase were: (a) testing seals with abrasive-laden mud on the low-pressure side; (b) test second and third generation designs of both elastomeric chevron seals and Teflon U-seals; and (c) testing a full-scale bearing/seal package. Several operating parameters which have a radical effect on seal life were identified, and some promising designs and materials were tested.

A new scientific drilling infrastructure in Sweden

NASA Astrophysics Data System (ADS)

Rosberg, J.-E.; Lorenz, H.

2012-04-01

A new scientific drilling infrastructure is currently under commissioning at Lund University in southern Sweden and is intended primarily for Swedish scientific drilling projects. However, it will be available to the scientific community and even industry when not occupied. The drill rig, a crawler mounted Atlas Copco CT20, was funded by the Swedish Research Council (VR) after an application by the Swedish scientific drilling community under the lead of Prof. Leif Bjelm, Lund University. As a national resource it is, together with support of the Swedish Deep Drilling Program (SDDP) and the Swedish membership in ICDP, part of VR's commitment to scientific drilling. The Atlas Copco CT20 is a top modern, versatile diamond wireline core-drilling rig which can handle P, H and N sizes. It can operate on very small drill sites (500-800 m2) and, thus, leaves a minimal environmental footprint. The crawler makes the rig ideal for operations in remote locations. A total of only 3-4 truckloads is necessary for mobilization of the basic drilling equipment. Main technical specifications are: Depth capacity coring, based on vertical water filled hole: P-size to around 1050 m, hole size 123 mm and core size 85 mm. H-size to around 1600 m, hole size 96 mm and core size 63 mm. N-size to around 2500 m, hole size 76 mm and core size 48 mm. Weight: Complete rig including crawler, wet - 23500 kg Dimensions in (length, width, height) transport position: 11560 x 2500 x 3750 mm. Available in-hole equipment: Complete core retrieval system for PQ, HQ and NQ-sizes, including PHD, HRQ (V-Wall) and NRQ (V-Wall) drill rods covering the maximum drilling depth for each size (see rig depth capacity above). Both dual and triple tube for HQ and NQ-sizes. Casing advancers (PW, HW, NW and BW). Casing PWT, HWT, NW and BW. Bits and reamers. Additional equipment: Mud cleaning and mixing system. MWD-system (Measurements While Drilling). Cementing equipment. Fishing tools (Bowen Spear). Blow Out Preventer (BOP). Deviation tools. Wireline packers. And more.

Borehole data transmission apparatus

DOEpatents

Kotlyar, O.M.

1993-03-23

A borehole data transmission apparatus is described whereby a centrifugal pump impeller(s) is used to provide a turbine stage having substantial pressure characteristics in response to changing rotational speed of a shaft for the pressure pulsing of data from the borehole through the drilling mud to the surface of the earth.

40 CFR 147.2902 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... loss of drilling mud into porous ground, or to prevent water, gas, or other fluid from entering the...: (a)(1) Which supplies any public water system; or (2) Which contains a sufficient quantity of ground water to supply a public water system; and (i) Currently supplies drinking water for human consumption...

30 CFR 250.490 - Hydrogen sulfide.

Code of Federal Regulations, 2013 CFR

2013-07-01

... absence of H2S has been confirmed. Well-control fluid means drilling mud and completion or workover fluid... information such as geologic and geophysical data and correlations, well logs, formation tests, cores and... concentration in the atmosphere reaches 5 ppm; (20) Engineering controls to protect personnel from SO2; and (21...

30 CFR 250.490 - Hydrogen sulfide.

Code of Federal Regulations, 2014 CFR

2014-07-01

... absence of H2S has been confirmed. Well-control fluid means drilling mud and completion or workover fluid... information such as geologic and geophysical data and correlations, well logs, formation tests, cores and... concentration in the atmosphere reaches 5 ppm; (20) Engineering controls to protect personnel from SO2; and (21...

30 CFR 250.490 - Hydrogen sulfide.

Code of Federal Regulations, 2012 CFR

2012-07-01

... absence of H2S has been confirmed. Well-control fluid means drilling mud and completion or workover fluid... information such as geologic and geophysical data and correlations, well logs, formation tests, cores and... concentration in the atmosphere reaches 5 ppm; (20) Engineering controls to protect personnel from SO2; and (21...

30 CFR 250.490 - Hydrogen sulfide.

Code of Federal Regulations, 2011 CFR

2011-07-01

... where neither the presence nor absence of H2S has been confirmed. Well-control fluid means drilling mud..., well logs, formation tests, cores and analysis of formation fluids; and (4) Submit a request for... initiate when the SO2 concentration in the atmosphere reaches 5 ppm; (20) Engineering controls to protect...

A comparative study on the effects of barite, ilmenite and bentonite on four suspension feeding bivalves.

PubMed

Strachan, Maia F; Kingston, Paul F

2012-10-01

The impact of drilling mud components on the filtration activity and survival of bivalve molluscs was investigated by exposing them to suspensions of 'standard' barite, finely milled barite, ilmenite and bentonite in sea water. Introduction of the components stimulated filtration activity in all four bivalves. In addition, the introduction of standard barite and ilmenite both had lethal effects, with none of the bivalves surviving the full duration of the experiments. In-vivo observations of the gill surfaces provided direct evidence of physical damage caused by the administration of barite and ilmenite. A marked difference between filtration activity and survival of animals dosed with 'standard' barite and 'fine' barite suggests that the observed effects were primarily caused by physical interference with gill function. The results also suggest that the use of fine barite in offshore drilling may provide a more favourable environmental impact profile than the use of ilmenite. Copyright © 2012. Published by Elsevier Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guliyev, I.A.; Aliyev, A.A.; Rahmanov, R.R.

Azerbaijan is a classic region for the study of mud volcanism. Of the 700 mud volcanoes known in the world, 220 are in Azerbaijan. These are of great interest, not least in relation to oil and gas exploration since they give information on subsurface sediments beyond the reach of drilling. Mud volcanoes are clearly visible on satellite images. They are confined to structural lineaments and associated fractures. Changes in the morphology of some mud volcanoes post-eruption can be detected from a series of images pre-dating and post-dating eruptions. Mud volcanoes are notable for gradients of temperature that are by anmore » order of magnitude or a factor of 102 greater than the temperature gradients established elsewhere. The gases of mud volcanoes consist mainly of methane (95-100%). There are small amounts of C{sub 2-6}, CO{sub 2}, N{sub 2}, He and Ar. The isotopic composition of carbon (ICC) within the methane varies from -61.29. to -35.W{close_quotes} which is isotopically heavier than the methane from producing fields. The ICC of the CO{sub 2} has a very wide range (from -49.6% to +23.1%), indicating several sources of its formation. The isotopically superheavy CO{sub 2} (+5%) is especially interesting. Oils from mud volcanoes are typically severely biodegraded. Their ICC ranges from -24.76% to -28.2%. A relationship between {partial_derivative}{sup l3}C of oils and ages of accumulations has been established. Waters of mud volcanoes are lightly mineralised, containing chiefly bicarbonates and sodium. The hydrogen composition of the water is abnormally heavy. Ejected rocks from mud volcanoes range in age from Cretaceous - Pliocene. Their study suggests that deeply buried reservoirs maintain good poroperm characteristics because of relatively little catagenesis.« less

The geological and petrological studies of the subduction boundaries and suggestion for the geological future work in Japan　- How to avoid ultra-mega-earthquakes -

NASA Astrophysics Data System (ADS)

Ishii, T.

2015-12-01

The Pacific plate is surrounded by circum-Pacific active margin, along which volcanic and seismic activities are very high. Ultra-Mega-Earthquakes (=UMEs, M>9.0) are occasionally observed along the margin, where sedimentary rocks of subducting slaves contact with the accreted sedimentary rocks of subducted slaves. But, those UME have never been occured along western Pacific islandarc-trench system including Izu-Ogasawara (=Bonin)-Mariana-Yap-Palau-Philippine-Tonga-Kermadec Trenches. I assume that the geological and petrological characteristics of the subduction boundaries are very important to understand those different seismic activities. Along the above mentioned trench inner wall, especially in the southern Mariana, mantle peridotites are widely distributed. Subducting slave contacts directly with the olivine dominant mantle peridotites of subducted slave, serpentinite layer can be deposited easily under hydrous oceanic sub-bottom environment and very slippery subduction boundaries are left along the subduction zone.On the other hand, those geological evidences give us some ideas on how to avoid UMEs in the Japanese Islands along Japan Trench and Nankai Trough in future. We will be able to change artificially from normal subduction boundaries with asperity zone into slippery subduction boundaries with serpentine layer, by means of serpentine mud injection toward the subduction boundaries interior by combining the following improved drilling technologies A and B. (A) Deep Sea Drilling Vessel CHIKYU has a drilling ability to reach subduction boundary with asperity zone in the Nankai Trough. (B) Advanced drilling technology in the shale gas industry is tremendous, that is, after one vertical deep drilling, horizontal drilling towards several direction are performed, then shale gas is collected by hydraulic fracturing method. I hope that, after several generations, our posterity will be able to avoid UMEs by continuous serpentine mud injection.

An Industry/DOE Program to Develop and Benchmark Advanced Diamond Product Drill Bits and HP/HT Drilling Fluids to Significantly Improve Rates of Penetration

DOE Office of Scientific and Technical Information (OSTI.GOV)

TerraTek

2007-06-30

A deep drilling research program titled 'An Industry/DOE Program to Develop and Benchmark Advanced Diamond Product Drill Bits and HP/HT Drilling Fluids to Significantly Improve Rates of Penetration' was conducted at TerraTek's Drilling and Completions Laboratory. Drilling tests were run to simulate deep drilling by using high bore pressures and high confining and overburden stresses. The purpose of this testing was to gain insight into practices that would improve rates of penetration and mechanical specific energy while drilling under high pressure conditions. Thirty-seven test series were run utilizing a variety of drilling parameters which allowed analysis of the performance ofmore » drill bits and drilling fluids. Five different drill bit types or styles were tested: four-bladed polycrystalline diamond compact (PDC), 7-bladed PDC in regular and long profile, roller-cone, and impregnated. There were three different rock types used to simulate deep formations: Mancos shale, Carthage marble, and Crab Orchard sandstone. The testing also analyzed various drilling fluids and the extent to which they improved drilling. The PDC drill bits provided the best performance overall. The impregnated and tungsten carbide insert roller-cone drill bits performed poorly under the conditions chosen. The cesium formate drilling fluid outperformed all other drilling muds when drilling in the Carthage marble and Mancos shale with PDC drill bits. The oil base drilling fluid with manganese tetroxide weighting material provided the best performance when drilling the Crab Orchard sandstone.« less

Episodic Deep Fluid Expulsion at Mud Volcanoes in the Kumano Forearc Basin, SE Offshore Japan

NASA Astrophysics Data System (ADS)

Hammerschmidt, S.; Kopf, A.

2014-12-01

Compressional forces at convergent margins govern a variety of processes, most prominently earthquakes, landslides and mud volcanoes in the forearc. Although all seem related to fluid pressure changes, mud volcanoes are not only characterized by expulsion of fluids, but also fluidized mud and clasts that got ripped-up during mud ascension. They hence provide information regarding mobilization depth, diagenetic overprint, and geodynamic pathways. At the Nankai Trough subduction zone, SE offshore Japan, mud volcanism id common and supposed to be related to seismogenic processes. During MARUM Expedition SO-222 with R/V SONNE, mud volcanoes in the Kumano forearc basin were mapped, cored and sampled. By extending the Integrated Ocean Drilling Program (IODP) Kumano transect landwards, 5 new mud volcanoes were identified by multibeam mapping. Cores revealed mud breccia with semi-consolidated silt- to claystone clasts and gaseous fluid escape structures, while the hemipelagic background sediments are characterized by intercalations of turbidites, ash layers and calcareous fossils. Clasts were subject to thin-section analyses, and the cores were sampled for XRD analyses and radiocarbon dating. Clasts showed prominent deformation structures, neomorphism and pores and fractures filled with polycrystalline quartz and/or calcite cement, probably formed during deep burial and early metamorphosis. Illite crystallinity based on XRD measurements varies between 0.24 and 0.38, which implies that the material originates from the Anchizone at depths ≥ 4 km. Radiocarbon dating revealed ages between 4450 and 30300 yr cal. BP, with age reversals occurring not earlier than 17000 yr cal. BP. Radiocarbon dating beneath turbidites and ash layers found at mud volcano #9 points to an episodic occurrence of these earthquake-related features in intervals of ca. 620 yr, while the mud volcano itself remained inactive. In summary, the preliminary results suggest that the mud volcanoes are nurtured from a reservoir within the older part of the accretionary prism, but that mud volcanic activity is less frequent than major earthquakes. Future models will focus on source depth and temperature, and might elucidate the prerequisites for fluid migration and its role in seismogenesis at the Nankai Trough subduction zone.

Hawaii Geothermal Project. Phase II: final report on well HGP-A extension to Contract E(04-3)-1093

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shupe, J.W.

1976-07-01

Drilling was completed on HGP-A to a depth of 6445 feet on April 27, 1976. A final core was taken; a series of logging runs performed, both with Gearhart-Owen equipment and with the Kuster temperature gauge; and the drill stem was withdrawn and laid down on the side adjacent to the rig - as a safety measure against possible volcanic tremors. A maximum temperature to date of 288/sup 0/C (550/sup 0/F) was recorded on May 13 at 4500 feet. The weighted temperature probe would penetrate no deeper into the drilling mud, which apparently is stiffening. The temperature depth relationship developedmore » in HGP-A is illustrated.« less

Fishing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, G.

1984-09-01

Two classifications of fishing jobs are discussed: open hole and cased hole. When there is no casing in the area of the fish, it is called open hole fishing. When the fish is inside the casing, it is called cased hole fishing. The article lists various things that can become a fish-stuck drill pipe, including: broken drill pipe, drill collars, bit, bit cones, hand tools dropped in the well, sanded up or mud stuck tubing, packers become stuck, and much more. It is suggested that on a fishing job, all parties involved should cooperate with each other, and that fishingmore » tool people obtain all the information concerning the well. That way they can select the right tools and methods to clean out the well as quickly as possible.« less

Systematics of Alkali Metals in Pore Fluids from Serpentinite Mud Volcanoes: IODP Expedition 366

NASA Astrophysics Data System (ADS)

Wheat, C. G.; Ryan, J.; Menzies, C. D.; Price, R. E.; Sissmann, O.

2017-12-01

IODP Expedition 366 focused, in part, on the study of geo­chemical cycling, matrix alteration, material and fluid transport, and deep biosphere processes within the subduction channel in the Mariana forearc. This was accomplished through integrated sampling of summit and flank regions of three active serpentinite mud volcanoes (Yinazao (Blue Moon), Asùt Tesoro (Big Blue), and Fantangisña (Celestial) Seamounts). These edifices present a transect of depths to the Pacific Plate, allowing one to characterize thermal, pressure and compositional effects on processes that are associated with the formation of serpentinite mud volcanoes and continued activity below and within them. Previous coring on ODP Legs 125 and 195 at two other serpentinite mud volcanoes (Conical and South Chamorro Seamounts) and piston, gravity, and push cores from several other Mariana serpentinite mud volcanoes add to this transect of sites where deep-sourced material is discharged at the seafloor. Pore waters (149 samples) were squeezed from serpentinite materials to determine the composition of deep-sourced fluid and to assess the character, extent, and effect of diagenetic reactions and mixing with seawater on the flanks of the seamounts as the serpentinite matrix weathers. In addition two Water Sampler Temperature Tool (WSTP) fluid samples were collected within two of the cased boreholes, each with at least 30 m of screened casing that allows formations fluids to discharge into the borehole. Shipboard results for Na and K record marked seamount-to-seamount differences in upwelling summit fluids, and complex systematics in fluids obtained from flank sites. Here we report new shore-based Rb and Cs measurements, two elements that have been used to constrain the temperature of the deep-sourced fluid. Data are consistent with earlier coring and drilling expeditions, resulting in systematic changes with depth (and by inference temperature) to the subduction channel.

Soil properties affecting wheat yields following drilling-fluid application.

PubMed

Bauder, T A; Barbarick, K A; Ippolito, J A; Shanahan, J F; Ayers, P D

2005-01-01

Oil and gas drilling operations use drilling fluids (mud) to lubricate the drill bit and stem, transport formation cuttings to the surface, and seal off porous geologic formations. Following completion of the well, waste drilling fluid is often applied to cropland. We studied potential changes in soil compaction as indicated by cone penetration resistance, pH, electrical conductivity (EC(e)), sodium adsorption ratio (SAR), extractable soil and total straw and grain trace metal and nutrient concentrations, and winter wheat (Triticum aestivum L. 'TAM 107') grain yield following water-based, bentonitic drilling-fluid application (0-94 Mg ha(-1)) to field test plots. Three methods of application (normal, splash-plate, and spreader-bar) were used to study compaction effects. We measured increasing SAR, EC(e), and pH with drilling-fluid rates, but not to levels detrimental to crop production. Field measurements revealed significantly higher compaction within areas affected by truck travel, but also not enough to affect crop yield. In three of four site years, neither drilling-fluid rate nor application method affected grain yield. Extractions representing plant availability and plant analyses results indicated that drilling fluid did not significantly increase most trace elements or nutrient concentrations. These results support land application of water-based bentonitic drilling fluids as an acceptable practice on well-drained soils using controlled rates.

New roles of LWD and wireline logging in scientific ocean drilling

NASA Astrophysics Data System (ADS)

Sanada, Y.; Kido, Y. N.; Moe, K.; Aoike, K.

2014-12-01

D/V Chikyu implemented by CDEX/JAMSTEC joined IODP from 2007. Various LWD (Logging While Drilling) and wireline logging have been carried out in many expeditions and for various purposes. Significant features of logging in Chikyu expeditions are many use of LWD than wireline logging, and riser dirlling. riser selected specific tools for each scientific target, and 3) carried out various borehole experiments. LWD has been more popular than wireline logging in Chikyu expeditions, because its advantages match theirs science targets. The advantages are followings. 1) LWD has more opportunities for measurement in unstable borehole, such as in the series of Nankai trough drilling expeditions. 2) LWD realtime data allows us to make realtime interpretation and operational decision. Realtime interpretation was required to set obsevartory at the properposition. 3) LWD before coring allows us to make a strategy of spot coring.We can design coring intervals for our interest and core length to improve core recovery.Riser drilling brings us merits for logging. One is hole stability (good hole condition) and the other is the use of large diameter tools. Controled drilling mud in riser drilling system prevent mud invasion to formation and mitigates collapse of borehole wall. They reduce the risk of tool stack and improve data quality. Large diameter of riser pipe enhances variation of tool seizes. A couple of new tools were used for new measurement and improvement of the data quality. For example, SonicScanner (trademark of Schulumberger) successfully measured compressional and share velocity in very low velocities at the soft sediment, where it has been difficult to measure them with conventional DSI tool (Exp319). The stress and pore pressure in the borehole were measured with the wireline logging tool, (Schlumberger MDT). The single probe tool enable to measure temporal formation fluid pressure. The double packer tool enable to fracture test by sealing and pumping in the borehole. These in-situ measurement and stress experiment data are very important to understand physical properties and mechanism of fault zone (Exp319).Those new technologies and tools also expand the envelope of scientific ocean drilling.

Experimental Study on Application of Boron Mud Secondary Resource to Oxidized Pellets Production

NASA Astrophysics Data System (ADS)

Fu, Xiao-Jiao; Chu, Man-Sheng; Zhao, Jia-Qi; Chen, Shuang-Yin; Liu, Zheng-Gen; Wang, Si-Yuan

2017-07-01

In order to realize comprehensive and massive treatment of boron mud secondary resource, fundamental study on boron mud applied to oxidized pellets production as additive was carried out in the paper under laboratory conditions. The effects of boron mud on the performance of oxidized pellets were investigated systemically, and boron mud was combined with other boron-rich material innovatively. The results showed that, within certain limits, boron mud can improve properties of oxidized pellets. The bentonite content decreased to 0.3 % when adding 1.0 % boron mud additive and the pellets met blast furnace requirements. With the combination additive content 0.8 %, bentonite content can be further decreased to 0.2 %, and the pellets properties were better than base pellet. Therefore, it was an effective way to reduce environmental pollution and optimize blast furnace operation by developing boron mud secondary resource as pellets additive.

Data Report: A Search for Deposits of the Late Pliocene Impact of the Eltanin Asteroid in Rise Sediments from the Antarctic Peninsula, Site 1096

NASA Technical Reports Server (NTRS)

Kyte, Frank T.

2003-01-01

Concentrations of Ir have been measured in 87 sediment samples from Ocean Drilling Program Site 1096 in search of evidence of fallout from the impact of the Eltanin asteroid, which occurred at 2.15 Ma, approx. 1300 km northwest of the site. An additional six samples were measured from a unique sand layer and adjacent sediments that are dated at approx. 1.6 Ma. These 93 sediment samples are all silts and muds that were deposited on a continental rise drift of the Antarctic Peninsula. No evidence of the Eltanin impact deposit was found in this study.

Investigation on the generation characteristic of pressure pulse wave signal during the measurement-while-drilling process

NASA Astrophysics Data System (ADS)

Changqing, Zhao; Kai, Liu; Tong, Zhao; Takei, Masahiro; Weian, Ren

2014-04-01

The mud-pulse logging instrument is an advanced measurement-while-drilling (MWD) tool and widely used by the industry in the world. In order to improve the signal transmission rate, ensure the accurate transmission of information and address the issue of the weak signal on the ground of oil and gas wells, the signal generator should send out the strong mud-pulse signals with the maximum amplitude. With the rotary valve pulse generator as the study object, the three-dimensional Reynolds NS equations and standard k - ɛ turbulent model were used as a mathematical model. The speed and pressure coupling calculation was done by simple algorithms to get the amplitudes of different rates of flow and axial clearances. Tests were done to verify the characteristics of the pressure signals. The pressure signal was captured by the standpiece pressure monitoring system. The study showed that the axial clearances grew bigger as the pressure wave amplitude value decreased and caused the weakening of the pulse signal. As the rate of flow got larger, the pressure wave amplitude would increase and the signal would be enhanced.

Force of resistance to pipeline pulling in plane and volumetrically curved wells

NASA Astrophysics Data System (ADS)

Toropov, V. S.; Toropov, S. Yu; Toropov, E. S.

2018-05-01

A method has been developed for calculating the component of the pulling force of a pipeline, arising from the well curvature in one or several planes, with the assumption that the pipeline is ballasted by filling with water or otherwise until zero buoyancy in the drilling mud is reached. This paper shows that when calculating this force, one can neglect the effect of sections with zero curvature. In the other case, if buoyancy of the pipeline is other than zero, the resistance force in the curvilinear sections should be calculated taking into account the difference between the normal components of the buoyancy force and weight. In the paper, it is proved that without taking into account resistance forces from the viscosity of the drilling mud, if buoyancy of the pipeline is zero, the total resistance force is independent of the length of the pipe and is determined by the angle equal to the sum of the entry angle and the exit angle of the pipeline to the day surface. For the case of the well curvature in several planes, it is proposed to perform the calculation of such volumetrically curved well by the central angle of the well profile. Analytical dependences are obtained that allow calculating the pulling force for well profiles with a variable curvature radius, i.e. at different angles of deviation between the drill pipes along the well profile.

Fluid-Rock Characterization for NMR Well Logging and Special Core Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Hirasaki; Kishore Mohanty

2007-12-31

The overall objective of this effort is to develop, build and test a high-speed drilling motor that can meet the performance guidelines of the announcement, namely: 'The motors are expected to rotate at a minimum of 10,000 rpm, have an OD no larger than 7 inches and work downhole continuously for at least 100 hours. The motor must have common oilfield thread connections capable of making up to a drill bit and bottomhole assembly. The motor must be capable of transmitting drilling fluid through the motor'. To these goals, APS would add that the motor must be economically viable, inmore » terms of both its manufacturing and maintenance costs, and be applicable to as broad a range of markets as possible. APS has taken the approach of using a system using planetary gears to increase the speed of a conventional mud motor to 10,000 rpm. The mud flow is directed around the outside of the gear train, and a unique flow diversion system has been employed. A prototype of the motor was built and tested in APS's high-pressure flow loop. The motor operated per the model up to {approx}4200 rpm. At that point a bearing seized and the performance was severely degraded. The motor is being rebuilt and will be retested outside of this program.« less

Data transmission element for downhole drilling components

DOEpatents

Hall, David R.; Hall, Jr., H. Tracy; Pixton, David S.; Dahlgren, Scott; Fox, Joe; Sneddon, Cameron; Briscoe, Michael

2006-01-31

A robust data transmission element for transmitting information between downhole components, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The data transmission element components include a generally U-shaped annular housing, a generally U-shaped magnetically conductive, electrically insulating element such as ferrite, and an insulated conductor. Features on the magnetically conducting, electrically insulating element and the annular housing create a pocket when assembled. The data transmission element is filled with a polymer to retain the components within the annular housing by filling the pocket with the polymer. The polymer can bond with the annular housing and the insulated conductor but preferably not the magnetically conductive, electrically insulating element. A data transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe.

The thermal structure of the mud diapir/volcano and its influence on gas hydrate stability in northern South China Sea

NASA Astrophysics Data System (ADS)

Wan, Z.; Xu, X.; Wang, X.

2016-12-01

The mud diapir/volcano is an important indicator for gas hydrate exploration, which develops widely in continental slopes. There are many mud diapirs/volcanoes developed in northern South China Sea continental slope. Guangzhou Marine Geological Survey (GMGS) of the Chinese Ministry of Land and Resources targeted mud diapirs/volcanoes and deployed gas hydrate drilling in the Shenhu area. An obvious mud diapir developed below borehole number SH5, and bottom-simulating reflection (BSR) was also detected, but no gas hydrates were found at this borehole. We analyzed the thermal structure of mud diapirs and their relationship to the occurrence of gas hydrates. The in situ temperature at the seafloor is approximately 2.2 2.5oC in the study area. Seafloor heat flow values of SH5 is 71.4mW/m2. Temperature increases rapidly to 17oC from 40 m to 100 m and stays in the range of 17 to 19oC below 100 m. And the thermal conductivity value of SH5 is approximately 1.0 W/m·k from top to bottom. The evolution of the mud diapir/volcanoes can be divided into three stages within a continuous geological process controlling the gas hydrate reservoir. During the late stage, liquid from the mud diapir/volcanoes begins to invade the gas hydrate stability zone . Because of the high unit heat capacity of liquid, the whole temperature field of the surrounding layers increases significantly when the mud diapir/volcanoes pierces upwards. This high heat flow leads to decomposition of the gas hydrates. Therefore, the reason of SH5 did not find gas hydrates may be that the mud diapir had pierced through during the late stage, leading to gas hydrate decomposition, even though there is an obvious BSR. This work was supported by Science and Technology Program of Guangzhou (No. 201607010214) and National Nature Science Foundation of China (No. 91128203,41102077).

Pressure charged airlift pump

DOEpatents

Campbell, Gene K.

1983-01-01

A pumping system is described for pumping fluids, such as water with entrained mud and small rocks, out of underground cavities such as drilled wells, which can effectively remove fluids down to a level very close to the bottom of the cavity and which can operate solely by compressed air pumped down through the cavity. The system utilizes a subassembly having a pair of parallel conduit sections (44, 46) adapted to be connected onto the bottom of a drill string utilized for drilling the cavity, the drill string also having a pair of coaxially extending conduits. The subassembly includes an upper portion which has means for connection onto the drill string and terminates the first conduit of the drill string in a plenum (55). A compressed air-driven pump (62) is suspended from the upper portion. The pump sucks fluids from the bottom of the cavity and discharges them into the second conduit. Compressed air pumped down through the first conduit (46) to the plenum powers the compressed air-driven pump and aerates the fluid in the second conduit to lift it to the earth's surface.

The Terrestrial Paleoclimatic Record of the Late Quaternary as Revealed by Drilling Lake Titicaca, Peru/Bolivia

NASA Astrophysics Data System (ADS)

Baker, P. A.; Fritz, S. C.; Seltzer, G. O.; Ballantyne, A. P.; Rigsby, C. A.

2004-12-01

Seven drill cores were recovered from Lake Titicaca during the NSF/ICDP/DOSECC drilling expedition of 2001; our most detailed multi-proxy analyses have been done on Core 2B raised from 232 m water depth in the central basin of the lake. This site was drilled to 139 mblf with 141 m of total sediment recovered (101%). The recovered sediments consist of two main lithologies, organic- and inorganic-carbon-rich (often-laminated) muds that alternate with detrital-rich muds. These lithologies represent respectively low and high lakestand deposits. Proxies for water level include planktic-to-benthic diatom ratio, sedimentary carbonate content, and stable isotopic ratio of organic carbon. There are six highstand intervals separated by five lowstand intervals indicating that the level and volume of Lake Titicaca underwent several large changes during the late Quaternary. We infer from high values of magnetic susceptibility in most highstand muds that glacial advances in the surrounding Andes coincided with periods of relative wetness. During the most recent lowstand, in the early and middle Holocene, Lake Titicaca fell to 85 m below its modern level, salinity increased several-fold, and the downstream Salar de Uyuni desiccated. By contrast, throughout the LGM from ca. 25,000 cal BP to 15,000 cal BP, Lake Titicaca was deep and fresh, and overflowed southward to the Salar de Uyuni. Prior to the LGM, back to ca. 53,000 BP, the lake was predominantly fresh and overflowing. Pulses of increased benthic diatom abundance and inorganic carbon concentration during that time were likely due to episodes of downslope transport. We believe (based on U-Th dates of authigenic carbonate layers) that the penultimate lowstand of Lake Titicaca (seismic evidence indicates a lake level 200 m lower than today) was coincident with MIS 5. We recovered sediments recording three older lowstands, each separated by periods in which the lake freshened dramatically and when glaciers apparently advanced in the Andes. We tentatively correlate these lowstands with MIS 7, 9, and 11. The high abundance of benthic diatoms in the lowermost 40 m of drill core may imply that the Altiplano was persistently drier than today, prior to and including MIS 9. Alternatively, basin morphometry may have been significantly different than today because of geomorphic or tectonic effects. This period apparently coincides with a period when the Salar de Uyuni was mostly dry and dominated by salt deposition.

Confined compressive strength analysis can improve PDC bit selection. [Polycrystalline Diamond Compact

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fabain, R.T.

1994-05-16

A rock strength analysis program, through intensive log analysis, can quantify rock hardness in terms of confined compressive strength to identify intervals suited for drilling with polycrystalline diamond compact (PDC) bits. Additionally, knowing the confined compressive strength helps determine the optimum PDC bit for the intervals. Computing rock strength as confined compressive strength can more accurately characterize a rock's actual hardness downhole than other methods. the information can be used to improve bit selections and to help adjust drilling parameters to reduce drilling costs. Empirical data compiled from numerous field strength analyses have provided a guide to selecting PDC drillmore » bits. A computer analysis program has been developed to aid in PDC bit selection. The program more accurately defines rock hardness in terms of confined strength, which approximates the in situ rock hardness downhole. Unconfined compressive strength is rock hardness at atmospheric pressure. The program uses sonic and gamma ray logs as well as numerous input data from mud logs. Within the range of lithologies for which the program is valid, rock hardness can be determine with improved accuracy. The program's output is typically graphed in a log format displaying raw data traces from well logs, computer-interpreted lithology, the calculated values of confined compressive strength, and various optional rock mechanic outputs.« less

Horizontal technology helps spark Louisiana`s Austin chalk trend

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koen, A.D.

1996-04-29

A handful of companies paced by some of the most active operators in the US are pressing the limits of horizontal technology to ramp up Cretaceous Austin chalk exploration and development (E and D) across Louisiana. Companies find applications in Louisiana for lessons learned drilling horizontal wells to produce chalk intervals in Texas in Giddings, Pearsall, and Brookeland fields. Continuing advances in horizontal well technology are helping operators deal with deeper, hotter reservoirs in more complex geological settings that typify the chalk in Louisiana. Better horizontal drilling, completion, formation evaluation, and stimulation techniques have enabled operators to produce oil andmore » gas from formations previously thought to be uneconomical. Most of the improved capabilities stem from better horizontal tools. Horizontal drilling breakthroughs include dual powered mud motors and retrievable whipstocks, key links in the ability to drill wells with more than one horizontal lateral. Better geosteering tools have enabled operators to maintain horizontal wellbores in desired intervals by signaling bit positions downhole while drilling. This paper reviews the technology and provides a historical perspective on the various drilling programs which have been completed in this trend. It also makes predictions on future drilling successes.« less

Mountain Home Air Force Base, Idaho Geothermal Resource Assessment and Future Recommendations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joseph C. Armstrong; Robert P. Breckenridge; Dennis L. Nielson

2013-03-01

The U.S. Air Force is facing a number of challenges as it moves into the future, one of the biggest being how to provide safe and secure energy to support base operations. A team of scientists and engineers met at Mountain Home Air Force Base in early 2011 near Boise, Idaho, to discuss the possibility of exploring for geothermal resources under the base. The team identified that there was a reasonable potential for geothermal resources based on data from an existing well. In addition, a regional gravity map helped identify several possible locations for drilling a new well. The teammore » identified several possible sources of funding for this well—the most logical being to use U.S. Department of Energy funds to drill the upper half of the well and U.S. Air Force funds to drill the bottom half of the well. The well was designed as a slimhole well in accordance with State of Idaho Department of Water Resources rules and regulations. Drilling operations commenced at the Mountain Home site in July of 2011 and were completed in January of 2012. Temperatures increased gradually, especially below a depth of 2000 ft. Temperatures increased more rapidly below a depth of 5500 ft. The bottom of the well is at 5976 ft, where a temperature of about 140°C was recorded. The well flowed artesian from a depth below 5600 ft, until it was plugged off with drilling mud. Core samples were collected from the well and are being analyzed to help understand permeability at depth. Additional tests using a televiewer system will be run to evaluate orientation and directions at fractures, especially in the production zone. A final report on the well exploitation will be forthcoming later this year. The Air Force will use it to evaluate the geothermal resource potential for future private development options at Mountain Home Air Force Base. In conclusion, Recommendation for follow-up efforts include the following:« less

Exploration and Resource Assessment at Mountain Home Air Force Base, Idaho Using an Integrated Team Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joseph C. Armstrong; Robert P. Breckenridge; Dennis L. Nielson

The U.S. Air Force is facing a number of challenges as it moves into the future, one of the biggest being how to provide safe and secure energy to support base operations. A team of scientists and engineers met at Mountain Home Air Force Base near Boise, Idaho, to discuss the possibility of exploring for geothermal resources under the base. The team identified that there was a reasonable potential for geothermal resources based on data from an existing well. In addition, a regional gravity map helped identify several possible locations for drilling a new well. The team identified several possiblemore » sources of funding for this well—the most logical being to use U.S. Department of Energy funds to drill the upper half of the well and U.S. Air Force funds to drill the bottom half of the well. The well was designed as a slimhole well in accordance with State of Idaho Department of Water Resources rules and regulations. Drilling operations commenced at the Mountain Home site in July of 2011 and were completed in January of 2012. Temperatures increased gradually, especially below a depth of 2000 ft. Temperatures increased more rapidly below a depth of 5500 ft. The bottom of the well is at 5976 ft, where a temperature of about 140°C was recorded. The well flowed artesian from a depth below 5600 ft, until it was plugged off with drilling mud. Core samples were collected from the well and are being analyzed to help understand permeability at depth. Additional tests using a televiewer system will be run to evaluate orientation and directions at fractures, especially in the production zone. A final report on the well exploitation will be forthcoming later this year. The Air Force will use it to evaluate the geothermal resource potential for future private development options at Mountain Home AFB.« less

30 CFR 250.1623 - Well-control fluids, equipment, and operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... measuring device for determining fluid volumes when filling the hole on trips, and (3) A recording mud-pit... and an audible warning device. (c) When coming out of the hole with drill pipe or a workover string... that may be pulled prior to filling the hole and the equivalent well-control fluid volume shall be...

30 CFR 250.1623 - Well-control fluids, equipment, and operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... measuring device for determining fluid volumes when filling the hole on trips, and (3) A recording mud-pit... and an audible warning device. (c) When coming out of the hole with drill pipe or a workover string... that may be pulled prior to filling the hole and the equivalent well-control fluid volume shall be...

30 CFR 250.1623 - Well-control fluids, equipment, and operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... measuring device for determining fluid volumes when filling the hole on trips, and (3) A recording mud-pit... and an audible warning device. (c) When coming out of the hole with drill pipe or a workover string... that may be pulled prior to filling the hole and the equivalent well-control fluid volume shall be...

46 CFR 108.171 - Class I, Division 1 locations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... locations. The following are Class I, Division 1 locations: (a) An enclosed space that contains any part of the mud circulating system that has an opening into the space and is between the well and final... possible source of gas release. (c) An enclosed space that is on the drill floor, and is not separated by a...

46 CFR 108.171 - Class I, Division 1 locations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... locations. The following are Class I, Division 1 locations: (a) An enclosed space that contains any part of the mud circulating system that has an opening into the space and is between the well and final... possible source of gas release. (c) An enclosed space that is on the drill floor, and is not separated by a...

46 CFR 108.171 - Class I, Division 1 locations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... locations. The following are Class I, Division 1 locations: (a) An enclosed space that contains any part of the mud circulating system that has an opening into the space and is between the well and final... possible source of gas release. (c) An enclosed space that is on the drill floor, and is not separated by a...

46 CFR 108.171 - Class I, Division 1 locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... locations. The following are Class I, Division 1 locations: (a) An enclosed space that contains any part of the mud circulating system that has an opening into the space and is between the well and final... possible source of gas release. (c) An enclosed space that is on the drill floor, and is not separated by a...

46 CFR 108.171 - Class I, Division 1 locations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... locations. The following are Class I, Division 1 locations: (a) An enclosed space that contains any part of the mud circulating system that has an opening into the space and is between the well and final... possible source of gas release. (c) An enclosed space that is on the drill floor, and is not separated by a...

“Can LUSI be stopped? - A case study and lessons learned from the relief wells”

NASA Astrophysics Data System (ADS)

Sutrisna, E.

2009-12-01

Since May 2006, in East Java, Indonesia, the LUSI mud volcano has been erupting huge volumes of mixture of predominately mud and water, with little sign of slowing down. It has disrupted social and economic life in this highly populated region. Most geologists believe LUSI is a naturally-occurring mud volcano (MV), like other MV in the Java island of particular interest are the MV along the Watukosek fault, such as, Kalang Anyar, Pulungan, Gunung Anyar, and Socah MV. All of these MV lie in the vicinity of the SSW/NNE trending Watukosek fault that passes through LUSI. The Porong collapse structure is an ancient MV closest to LUSI approx. 7 km away, which on seismic sections demonstrate its complex multi-branching plumbing system. Assuming that the mudflow passed through the wellbore due to an underground blowout, relief wells (RW) were planned to kill the mudflow and carried out in 3 stages, these were: 1. Re-entering the original Banjarpanji-1 (BJP-1) well to obtain accurate survey data so the relief wells could be steered into intersect this original well. 2. Drilling a monitoring well (M-1) to ascertain whether the soil had sufficient strength to support relief wells. 3. Drilling RW-1 and RW-2. Both RW-1 and RW-2 suffered of surface and subsurface problems never achieved their objectives and had to be aborted. Numbers of good lessons were learned from the relief well initiative, such as: 1. No gas or liquid flowed from the wellhead area when it was excavated one month after the eruption started. The wellhead remained intact and totally dead suggesting that the mud flowed to surface through a fault zone or a fracture network instead of up the wellbore. 2. The ‘fish’ in BJP-1 wellbore was found at its original location and not eroded away. This suggests that the mud flow did not pass through the wellbore. 3. The Temperature log showed lower temp. than surface mud temp. The Sonan log response was quiet. These results suggest that there was no near casing mudflow. 4. Dynamic subsurface conditions of the area with shear movement at a depth of 1,100 ft to 1,500 ft. 5. The RW-1 experienced alternate loss and kicks at a depth of around 3,200 ft. as it entered the unstable fault zone and fracture network which likely served as the mud flow conduit. Drilling in the zone of instability around the mudflow conduit cannot be avoided and is full of hazards. 6. The area suffers a dynamic geological condition. The subsidence rate at the rig site of more than 100 cm in a month. The subsidence also had a lateral component. 7. LUSI has multiple mudflow conduits as reflected in the more than 100 gas bubbles currently occurring within a radius of 1.5 km. Although the relief wells did not achieve their intended purpose to stop the mudflow, they allowed the collection of valuable data, all of which suggests that the mudflow did not originate from the BJP-1 wellbore as originally assumed. The use of relief wells to kill the mudflow is a futile attempt since in such complex plumbing system. New conduits or the two dormant mudflow centers along the fault line that appeared at the beginning of LUSI may reactivate if the currently active conduit is blocked. In conclusion, LUSI appears to be another naturally occurring MV that is impossible to kill using relief wells.

Environmental effects monitoring at the Terra Nova offshore oil development (Newfoundland, Canada): Program design and overview

NASA Astrophysics Data System (ADS)

DeBlois, Elisabeth M.; Tracy, Ellen; Janes, G. Gregory; Crowley, Roger D.; Wells, Trudy A.; Williams, Urban P.; Paine, Michael D.; Mathieu, Anne; Kilgour, Bruce W.

2014-12-01

An environmental effects monitoring (EEM) program was developed by Suncor (formerly Petro-Canada) in 1997/98 to assess effects of the Terra Nova offshore oil and gas development on the receiving environment. The Terra Nova Field is located on the Grand Banks approximately 350 km southeast of Newfoundland (Canada), at approximately 100 m water depth. The EEM program was developed with guidance from experts in government, academia and elsewhere, and with input from the public. The EEM program proposed by Suncor was accepted by Canadian regulatory agencies and the program was implemented in 2000, 2001, 2002, 2004, 2006, 2008 and 2010, with pre-development sampling in 1997. The program continues to be implemented every two years. EEM includes an assessment of alterations in sediment quality through examination of changes in sediment chemistry, particle size, toxicity and benthic invertebrate community structure. A second component of the program examines potential effects on two species of commercial fishing interest: Iceland scallop (Chlamys islandica) and American plaice (Hippoglossoides platessoides). Chemical body burden for these two species is examined and taste tests are performed to assess the presence of taint in edible tissues. Effects on American plaice bioindicators are also examined. A final component of the program assesses potential effects of the Terra Nova development on water quality and examines water column chemistry, chlorophyll concentration and physical properties. The papers presented in this collection focus on effects of drill cuttings and drilling muds on the seafloor environment and, as such, report results on sediment quality and bioaccumulation of drilling mud components in Iceland scallop and American plaice. This paper provides information on drilling discharges, an overview of the physical oceanography at the Terra Nova Field, and an overview of the field program designed to assess environmental effects of drilling at Terra Nova.

Graphene nanoplatelets as high-performance filtration control material in water-based drilling fluids

NASA Astrophysics Data System (ADS)

Ridha, Syahrir; Ibrahim, Arif; Shahari, Radzi; Fonna, Syarizal

2018-05-01

The main objective of this work is to evaluate the effectiveness of graphene nanoplatelets (GNP) as filtration control materials in water based drilling fluids. Three (3) general samples of water based drilling fluids were prepared including basic potassium chloride (KCl) drilling fluids, nanosilica (NS) drilling fluids and GNP drilling fluids. Several concentrations of NS and GNP were dispersed in controlled formulations of water based drilling fluids. Standard API filtration tests were carried out for comparison purposes as well as High Temperature High Pressure (HTHP) filtration tests at 150 °F (∼66 °C), 250 °F (∼121 °C) and 350 °F (∼177 °C) at a fixed 500 (∼3.45MPa) psi to study the filtration trend as a function of temperature. Mud cake samples from several tests were selectively chosen and analyzed under Field Emission Scanning Electron Microscope (FESEM) for its morphology. Results from this work show that nanoparticle concentrations play a factor in filtration ability of colloid materials in water based drilling fluids when studied at elevated temperature. Low temperature filtration, however, shows only small differences in volume in all the drilling fluid samples. 0.1 ppb concentrations of GNP reduced the fluid loss of 350 °F by 4.6 mL as compared to the similar concentration of NS drilling fluids.

Numerical modelling for quantitative environmental risk assessment for the disposal of drill cuttings and mud

NASA Astrophysics Data System (ADS)

Wahab, Mohd Amirul Faiz Abdul; Shaufi Sokiman, Mohamad; Parsberg Jakobsen, Kim

2017-10-01

To investigate the fate of drilling waste and their impacts towards surrounding environment, numerical models were generated using an environmental software; MIKE by DHI. These numerical models were used to study the transportation of suspended drill waste plumes in the water column and its deposition on seabed in South China Sea (SCS). A random disposal site with the model area of 50 km × 25 km was selected near the Madalene Shoal in SCS and the ambient currents as well as other meteorological conditions were simulated in details at the proposed location. This paper was focusing on sensitivity study of different drill waste particle characteristics on impacts towards marine receiving environment. The drilling scenarios were obtained and adapted from the oil producer well at offshore Sabah (Case 1) and data from actual exploration drilling case at Pumbaa location (PL 469) in the Norwegian Sea (Case 2). The two cases were compared to study the effect of different drilling particle characteristics and their behavior in marine receiving environment after discharged. Using the Hydrodynamic and Sediment Transport models simulated in MIKE by DHI, the variation of currents and the behavior of the drilling waste particles can be analyzed and evaluated in terms of multiple degree zones of impacts.

Rowan Gorilla I rigged up, heads for eastern Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-03-01

Designed to operate in very hostile offshore environments, the first of the Rowan Gorilla class of self-elevating drilling rigs has been towed to its drilling assignment offshore Nova Scotia. About 40% larger than other jackups, these rigs can operate in 300 ft of water, drilling holes as deep as 30,000 ft. They also feature unique high-pressure and solids control systems that are expected to improve drilling procedures and efficiencies. A quantitative formation pressure evaluation program for the Hewlett-Packard HP-41 handheld calculator computes formation pressures by three independent methods - the corrected d exponent, Bourgoyne and Young, and normalized penetration ratemore » techniques for abnormal pressure detection and computation. Based on empirically derived drilling rate equations, each of the methods can be calculated separately, without being dependent on or influenced by the results or stored data from the other two subprograms. The quantitative interpretation procedure involves establishing a normal drilling rate trend and calculating the pore pressure from the magnitude of the drilling rate trend or plotting parameter increases above the trend line. Mobil's quick, accurate program could aid drilling operators in selecting the casing point, minimizing differential sticking, maintaining the proper mud weights to avoid kicks and lost circulation, and maximizing penetration rates.« less

Coiled tubing drilling with supercritical carbon dioxide

DOEpatents

Kolle , Jack J.

2002-01-01

A method for increasing the efficiency of drilling operations by using a drilling fluid material that exists as supercritical fluid or a dense gas at temperature and pressure conditions existing at a drill site. The material can be used to reduce mechanical drilling forces, to remove cuttings, or to jet erode a substrate. In one embodiment, carbon dioxide (CO.sub.2) is used as the material for drilling within wells in the earth, where the normal temperature and pressure conditions cause CO.sub.2 to exist as a supercritical fluid. Supercritical carbon dioxide (SC--CO.sub.2) is preferably used with coiled tube (CT) drilling equipment. The very low viscosity SC--CO.sub.2 provides efficient cooling of the drill head, and efficient cuttings removal. Further, the diffusivity of SC--CO.sub.2 within the pores of petroleum formations is significantly higher than that of water, making jet erosion using SC--CO.sub.2 much more effective than water jet erosion. SC--CO.sub.2 jets can be used to assist mechanical drilling, for erosion drilling, or for scale removal. A choke manifold at the well head or mud cap drilling equipment can be used to control the pressure within the borehole, to ensure that the temperature and pressure conditions necessary for CO.sub.2 to exist as either a supercritical fluid or a dense gas occur at the drill site. Spent CO.sub.2 can be vented to the atmosphere, collected for reuse, or directed into the formation to aid in the recovery of petroleum.

Gypsum addition to soils contaminated by red mud: implications for aluminium, arsenic, molybdenum and vanadium solubility.

PubMed

Lehoux, Alizée P; Lockwood, Cindy L; Mayes, William M; Stewart, Douglas I; Mortimer, Robert J G; Gruiz, Katalin; Burke, Ian T

2013-10-01

Red mud is highly alkaline (pH 13), saline and can contain elevated concentrations of several potentially toxic elements (e.g. Al, As, Mo and V). Release of up to 1 million m(3) of bauxite residue (red mud) suspension from the Ajka repository, western Hungary, caused large-scale contamination of downstream rivers and floodplains. There is now concern about the potential leaching of toxic metal(loid)s from the red mud as some have enhanced solubility at high pH. This study investigated the impact of red mud addition to three different Hungarian soils with respect to trace element solubility and soil geochemistry. The effectiveness of gypsum amendment for the rehabilitation of red mud-contaminated soils was also examined. Red mud addition to soils caused a pH increase, proportional to red mud addition, of up to 4 pH units (e.g. pH 7 → 11). Increasing red mud addition also led to significant increases in salinity, dissolved organic carbon and aqueous trace element concentrations. However, the response was highly soil specific and one of the soils tested buffered pH to around pH 8.5 even with the highest red mud loading tested (33 % w/w); experiments using this soil also had much lower aqueous Al, As and V concentrations. Gypsum addition to soil/red mud mixtures, even at relatively low concentrations (1 % w/w), was sufficient to buffer experimental pH to 7.5-8.5. This effect was attributed to the reaction of Ca(2+) supplied by the gypsum with OH(-) and carbonate from the red mud to precipitate calcite. The lowered pH enhanced trace element sorption and largely inhibited the release of Al, As and V. Mo concentrations, however, were largely unaffected by gypsum induced pH buffering due to the greater solubility of Mo (as molybdate) at circumneutral pH. Gypsum addition also leads to significantly higher porewater salinities, and column experiments demonstrated that this increase in total dissolved solids persisted even after 25 pore volume replacements. Gypsum addition could therefore provide a cheaper alternative to recovery (dig and dump) for the treatment of red mud-affected soils. The observed inhibition of trace metal release within red mud-affected soils was relatively insensitive to either the percentage of red mud or gypsum present, making the treatment easy to apply. However, there is risk that over-application of gypsum could lead to detrimental long-term increases in soil salinity.

IODP Expedition 366 Reveals Widespread Seamount Subduction Effects in the Mariana Forearc

NASA Astrophysics Data System (ADS)

Fryer, P. B.; Wheat, C. G.; Williams, T.

2017-12-01

Numerous studies of the subduction of seamounts at accretionary convergent plate margins show considerable vertical tectonic deformation in the forearc region. This includes embayment of the trench axis, steepening of the inner trench slope, the creation of troughs in the wake of the seamount track beneath the forearc sediment wedge, but hypotheses regarding the seismogenic consequences of these processes are frequently at odds. In the nonaccretionary Mariana convergent plate margin, it is clear that ridges crosscut the entire forearc region in commensurate dimensions with thicker areas of subducting Pacific plate. Furthermore, to-date deep-sea drilling results on ODP Legs 125 and 195 and on IODP Expedition 366 recovered seamount materials from 5 serpentinite mud volcanoes over a 640 km along-strike distance, within 90 km west of the trench axis, and from 13 to 19 km depth to slab. The location of the serpentinite mud volcanoes is always associated with fault lineaments. The faulting creates the conduits for eruption of mixtures of fluids from the subduction channel and fault gouge from both the subduction channel and the forearc lithosphere. Cores from IODP 366 confirm that seamount subduction and deformation is a temporally and spatially pervasive process on the Mariana forearc. The new findings provide windows on a continuum of the evolution of plate and seamount subduction from the trench to nearly 20 km depth within the subduction channel. Cased boreholes were deployed at the summits of three active serpentinite mud volcanoes (Yinazao (Blue Moon), Asùt Tesoro (Big Blue), and Fantangisña (Celestial) Seamounts) during Expedition 366. These, plus the existing borehole observatory at ODP Site 1200C on the active summit of Conical Seamount provide a means to monitor processes of subduction related to serpentinite mud volcanism of the Mariana forearc. Such drilling results and borehole observations impact current paradigms of lithospheric deformation, mass cycling, and physical conditions within the subduction channel.

Can introduction of hydraulic fracturing fluids induce biogenic methanogenesis in the shale reservoirs?

NASA Astrophysics Data System (ADS)

Sharma, S.; Wilson, T.; Wrighton, K. C.; Borton, M.; O'Banion, B.

2017-12-01

The hydraulic fracturing fluids (HFF) injected into the shale formation are composed primarily of water, proppant and some chemical additives ( 0.5- 2% by volume). The additives contain a lot of organic and inorganic compounds like ammonium sulfate, guar gum, boric acid, hydrochloric acid, citric acid, potassium carbonate, glutaraldehyde, ethylene glycols which serve as friction reducers, gelling agents, crosslinkers, biocides, corrosion/scale inhibitors, etc. The water and additives introduced into the formation ensue a variety of microbiogechmical reactions in the reservoir. For this study produced, water and gas samples were collected from several old and new Marcellus wells in SE Pennsylvania and NE West Virginia to better understand these microbe-water-rock interactions. The carbon isotopic composition of dissolved inorganic carbon (δ13CDIC) in the produced fluids and CO2 in produced gas (δ13CCO2) are highly enriched with values > +10‰ and +14 ‰ V-PDB respectively. The injected hydraulic fracturing fluid had low δ13CDIC values of < -8‰ V-PDB. The high carbon isotope values in produced fluids and gas possibly indicate 1) dissolution of 13C enriched carbonates in the host rock of reservoir, cement or drilling muds or 2) biogenic methanogenesis in the reservoir. The carbon signatures of carbonates in and around the landing zone and all possible sources of carbon put downhole were analyzed for their 13C signatures. The cement and silica sand had no detectable carbon in them. The drilling mud and carbonate veins had δ13C values of -1.8 and < 2.0 ‰ V-PDB respectively. Therefore, the high δ13CDIC signatures in produced water are possibly due to the microbial utilization of lighter carbon (12C) by microbes or methanogenic bacteria in the reservoir. It is possible that introduction of C containing nutrients like guar, methanol, methylamines, etc. stimulates certain methanogen species in the reservoir to produce biogenic methane. Genomic analysis reveals that methanogen species like Methanohalophilus or Methanolobus could be the possible sources of biogenic methane in these shale reservoirs. The evidence of microbial methanogenesis raises the possibility of enhanced gas recovery from these shales using biological amendments.

Accessing SAFOD data products: Downhole measurements, physical samples and long-term monitoring

NASA Astrophysics Data System (ADS)

Weiland, C.; Zoback, M.; Hickman, S. H.; Ellsworth, W. L.

2005-12-01

Many different types of data were collected during SAFOD Phases 1 and 2 (2004-2005) as part of the National Science Foundation's EarthScope program as well as from the SAFOD Pilot Hole, drilled in 2002 and funded by the International Continental Drilling Program (ICDP). Both SAFOD and the SAFOD Pilot Hole are being conducted as a close collaboration between NSF, the U.S. Geological Survey and the ICDP. SAFOD data products include cuttings, core and fluid samples; borehole geophysical measurements; and strain, tilt, and seismic recordings from the multilevel SAFOD borehole monitoring instruments. As with all elements of EarthScope, these data (and samples) are openly available to members of the scientific and educational communities. This paper presents the acquisition, storage and distribution plan for SAFOD data products. Washed and unwashed drill cuttings and mud samples were collected during Phases 1 and 2, along with three spot cores at depths of 1.5, 2.5, and 3.1 km. A total of 52 side-wall cores were also collected in the open-hole interval between 2.5 and 3.1 km depth. The primary coring effort will occur during Phase 3 (2007), when we will continuously core up to four, 250-m-long multilaterals directly within and adjacent to the San Andreas Fault Zone. Drill cuttings, core, and fluid samples from all three Phases of SAFOD drilling are being curated under carefully controlled conditions at the Integrated Ocean Drilling Program (IODP) Gulf Coast Repository in College Station, Texas. Photos of all physical samples and a downloadable sample request form are available on the ICDP website (http://www.icdp-online.de/sites/sanandreas/index/index.html). A suite of downhole geophysical measurements was conducted during the first two Phases of SAFOD drilling, as well as during drilling of the SAFOD Pilot Hole. These data include density, resistivity, porosity, seismic and borehole image logs and are also available via the ICDP website. The SAFOD monitoring program includes fiber-optic strain, tilt, seismic and fluid-pressure recording instruments. Seismic data from the Pilot Hole array are now available in SEED format from the Northern California Earthquake Data Center (http://quake.geo.berkeley.edu/safod/). The strain and tilt instruments are still undergoing testing and quality assurance, and these data will be available through the same web site as soon as possible. Lastly, two terabytes of unprocessed (SEG-2 format) data from a two-week deployment of an 80-level seismic array during April/May 2005 by Paulsson Geophysical Services, Inc. are now available via the IRIS data center (http://www.iris.edu/data/data.htm). Drilling parameters include real-time descriptions of drill cuttings mineralogy, drilling mud properties, and mechanical data related to the drilling process and are available via the ICDP web site. Current status reports on SAFOD drilling, borehole measurements, sampling, and monitoring instrumentation will continue to be available from the EarthScope web site (http://www.earthscope.org).

Map showing thickness of young bay mud, southern San Francisco Bay, California

USGS Publications Warehouse

McDonald, Sandra D.; Nichols, Donald R.; Wright, Nancy A.; Atwater, Brian

1978-01-01

Soft water-saturated estuarine deposits less than 10,000 years old underlie the southern part of San Francisco bay and the present and former marshlands that border the bay. Known locally as bay mud or as young bay mud, these deposits, and the estuarine environment that produces them, are of major importance in making decision on land use and development in the San Francisco Bay area. Knowledge of the distribution, thickness, and physical properties of young bay mud is critical to the feasibility, design, and maintenance of structures built on it. Fore this reason, numerous attempts have been made in the past to map or describe these characteristics (Mitchell, 1963; Goldman, 1969; McDonald and Nichols, 1974). The accompanying map of bay-mud thickness significantly revises part of an earlier compilation by Kahle and Goldman (1969) and includes new data from approximately 2400 boreholes, most of which have been drilled during the past 15 years. It also incorporates information on historic margins of San Francisco Bay and its tidal marshes (Nichols and Wright, 1971). Although this map was compelled mostly from data gathered during foundation investigations and construction projects, it is mostly from data gathered during foundation investigations and construction projects, it is not a substitute for such studies. Rather, the map provides regional information for land-use planning, seismic zonation, and design of foundation investigations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chevallier, J.; Turner, L.

There's a great deal of data recorded during drilling operations on rigs these days, but it is seldom well utilized. The operator's company person relies upon mud loggers for collecting and recording most information. The methods used to process and display this information are often inadequate for those who need it the most the driller and toolpusher. Drilling contractor personnel usually have only rudimentary displays of drilling parameters, and practically no serious method of analysis except for daily paper reports. These are cumbersome to use and provide only incomplete data, after the fact. The MDS system, presented in this article,more » is a new information and alarm network, which rectifies this situation by bringing to the rig, for the first time, the latest in sensor and computer technologies. This system acquires key drilling data on the rig floor, pump room, and return line, and displays it in a clear graphical format to both the driller and the toolpusher in real time. It also provides the toolpusher with a workstation for easy access to the same information for evaluation and planning of the drilling program.« less

Planetary Drilling and Resources at the Moon and Mars

NASA Technical Reports Server (NTRS)

George, Jeffrey A.

2012-01-01

Drilling on the Moon and Mars is an important capability for both scientific and resource exploration. The unique requirements of spaceflight and planetary environments drive drills to different design approaches than established terrestrial technologies. A partnership between NASA and Baker Hughes Inc. developed a novel approach for a dry rotary coring wireline drill capable of acquiring continuous core samples at multi-meter depths for low power and mass. The 8.5 kg Bottom Hole Assembly operated at 100 We and without need for traditional drilling mud or pipe. The technology was field tested in the Canadian Arctic in sandstone, ice and frozen gumbo. Planetary resources could play an important role in future space exploration. Lunar regolith contains oxygen and metals, and water ice has recently been confirmed in a shadowed crater at the Moon.s south pole. Mars possesses a CO2 atmosphere, frozen water ice at the poles, and indications of subsurface aquifers. Such resources could provide water, oxygen and propellants that could greatly simplify the cost and complexity of exploration and survival. NASA/JSC/EP/JAG

Slim hole drilling and testing strategies

NASA Astrophysics Data System (ADS)

Nielson, Dennis L.; Garg, Sabodh K.; Goranson, Colin

2017-12-01

The financial and geologic advantages of drilling slim holes instead of large production wells in the early stages of geothermal reservoir assessment has been understood for many years. However, the practice has not been fully embraced by geothermal developers. We believe that the reason for this is that there is a poor understanding of testing and reservoir analysis that can be conducted in slim holes. In addition to reservoir engineering information, coring through the cap rock and into the reservoir provides important data for designing subsequent production well drilling and completion. Core drilling requires significantly less mud volume than conventional rotary drilling, and it is typically not necessary to cure lost circulation zones (LCZ). LCZs should be tested by either production or injection methods as they are encountered. The testing methodologies are similar to those conducted on large-diameter wells; although produced and/or injected fluid volumes are much less. Pressure, temperature and spinner (PTS) surveys in slim holes under static conditions can used to characterize temperature and pressure distribution in the geothermal reservoir. In many cases it is possible to discharge slim holes and obtain fluid samples to delineate the geochemical properties of the reservoir fluid. Also in the latter case, drawdown and buildup data obtained using a downhole pressure tool can be employed to determine formation transmissivity and well properties. Even if it proves difficult to discharge a slim hole, an injection test can be performed to obtain formation transmissivity. Given the discharge (or injection) data from a slimhole, discharge properties of a large-diameter well can be inferred using wellbore modeling. Finally, slim hole data (pressure, temperature, transmissivity, fluid properties) together with reservoir simulation can help predict the ability of the geothermal reservoir to sustain power production.

Kick Detection at the Bit: Early Detection via Low Cost Monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tost, Brian; Rose, Kelly; Aminzadeh, Fred

2016-06-07

Formation fluid influxes (i.e. kicks) pose persistent challenges and operational costs during drilling operations. Implications of kicks range in scale but cumulatively result in substantial costs that affect drilling safety, environment, schedule, and infrastructure. Early kick detection presents a low-cost, easily adopted solution for avoiding well control challenges associated with kicks near the bit. Borehole geophysical tools used during the drilling process as part of the logging-while-drilling (LWD) and measurement-while-drilling (MWD) provide the advantage of offering real-time downhole data. LWD/MWD collect data on both the annulus and borehole wall. The annular data are normally treated as background, and are filteredmore » out to isolate the formation measurements. Because kicks will change the local physical properties of annular fluids, bottom-hole measurements are among the first indicators that a formation fluid has invaded the wellbore. This report describes and validates a technique for using the annular portion of LWD/MWD data to facilitate early kick detection using first order principles. The detection technique leverages data from standard and cost-effective technologies that are typically implemented during well drilling, such as MWD/LWD data in combination with mud-pulse telemetry for data transmission.« less

Characterizing the Weeks Island Salt Dome drilling of and seismic measurements from boreholes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattler, A.R.; Harding, R.S.; Jacobson, R.D.

1996-10-01

A sinkhole 36 ft across, 30 ft deep was first observed in the alluvium over the Weeks Island Salt Dome (salt mine converted for oil storage by US Strategic Petroleum Reserve) May 1992. Four vertical, two slanted boreholes were drilled for diagnostics. Crosswell seismic data were generated; the velocity images suggest that the sinkhole collapse is complicated, not a simple vertical structure. The coring operation was moderately difficult; limited core was obtained through the alluvium, and the quality of the salt core from the first two vertical wells was poor. Core quality improved with better bit selection, mud, and drillingmore » method. The drilling fluid program provided fairly stable holes allowing open hole logs to be run. All holes were cemented successfully (although it took 3 attempts in one case).« less

[The influence of the oil and gas industry on environmental safety and population health in the Khanty-Mansiĭskiĭ Region - Iugra].

PubMed

Samutin, N M; Vorob'ev, V O; Butorin, N N

2013-01-01

Production activities of oil and gas industry plants are related to technogenic impact on the environment, which has a high environmental risk. This is associated with low levels of environmental orientation of sheer technological processes of exploration and exploitation of hydrocarbons and also used in this technical means, materials and chemical reagents. The main pollutants that deteriorate the toxic characteristics of drilling waste, are the most likely drilling fluids, mud flush agents and chemicals, which enter into their composition. Existing methods of disposal of drilling wastes are not effective, the technology of their use is often violated. Dumping drilling waste into water bodies and burying toxic waste in water protection areas under the guise of processed waste has been observed. In the region there are significantly exceeded the national average values rate of morbidity of allergic, cardiovascular, pulmonary and cancer diseases, mediated by environmental factors and new monofactorial and multifactorial diseases appear.

Addition of an organic amendment and/or residue mud to bauxite residue sand in order to improve its properties as a growth medium.

PubMed

Jones, B E H; Haynes, R J; Phillips, I R

2012-03-01

The effects of addition of carbonated residue mud (RMC) or seawater neutralized residue mud (RMS), at two rates, in the presence or absence of added green waste compost, on the chemical, physical and microbial properties of gypsum-treated bauxite residue sand were studied in a laboratory incubation study. The growth of two species commonly used in revegetation of residue sand (Lolium rigidum and Acacia saligna) in the treatments was then studied in a 18-week greenhouse study. Addition of green waste-based compost increased ammonium acetate-extractable (exchangeable) Mg, K and Na. Addition of residue mud at 5 and 10% w/w reduced exchangeable Ca but increased that of Mg and Na (and K for RMS). Concentrations of K, Na, Mg and level of EC in saturation paste extracts were increased by residue mud additions. Concentrations of cations in water extracts were considerably higher than those in saturation paste extracts but trends with treatment were broadly similar. Addition of both compost and residue mud caused a significant decrease in macroporosity with a concomitant increase in mesoporosity and microporosity, available water holding capacity and the quantity of water held at field capacity. Increasing rates of added residue mud reduced the percentage of sample present as discrete sand particles and increased that in aggregated form (particularly in the 1-2 and >10mm diameter ranges). Organic C content, C/N ratio, soluble organic C, microbial biomass C and basal respiration were increased by compost additions. Where compost was added, residue mud additions caused a substantial increase in microbial biomass and basal respiration. L. rigidum grew satisfactorily in all treatments although yields tended to be reduced by additions of mud (especially RMC) particularly in the absence of added compost. Growth of A. saligna was poor in sand alone and mud-amended sand and was greatly promoted by additions of compost. However, in the presence of compost, addition of carbonated mud had a marked depressive effect on both top and root growth. The significant positive effect of compost was attributed to substantial inputs of K and marked reductions in the Na/K ratio in soil solution while the depressive effect of RMC was attributed to its greater alkalinity and consequently higher concentrations of HCO(3)(-) in solution. Copyright © 2011 Elsevier Ltd. All rights reserved.

Environmental corrections of a dual-induction logging while drilling tool in vertical wells

NASA Astrophysics Data System (ADS)

Kang, Zhengming; Ke, Shizhen; Jiang, Ming; Yin, Chengfang; Li, Anzong; Li, Junjian

2018-04-01

With the development of Logging While Drilling (LWD) technology, dual-induction LWD logging is not only widely applied in deviated wells and horizontal wells, but it is used commonly in vertical wells. Accordingly, it is necessary to simulate the response of LWD tools in vertical wells for logging interpretation. In this paper, the investigation characteristics, the effects of the tool structure, skin effect and drilling environment of a dual-induction LWD tool are simulated by the three-dimensional (3D) finite element method (FEM). In order to closely simulate the actual situation, real structure of the tool is taking into account. The results demonstrate that the influence of the background value of the tool structure can be eliminated. The values of deducting the background of a tool structure and analytical solution have a quantitative agreement in homogeneous formations. The effect of measurement frequency could be effectively eliminated by chart of skin effect correction. In addition, the measurement environment, borehole size, mud resistivity, shoulder bed, layer thickness and invasion, have an effect on the true resistivity. To eliminate these effects, borehole correction charts, shoulder bed correction charts and tornado charts are computed based on real tool structure. Based on correction charts, well logging data can be corrected automatically by a suitable interpolation method, which is convenient and fast. Verified with actual logging data in vertical wells, this method could obtain the true resistivity of formation.

Effects of drilling fluids on soils and plants: I. Individual fluid components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, R.W.; Honarvar, S.; Hunsaker, B.

1980-01-01

The effects of 31 drilling fluid (drilling mud) components on the growth of green beans (Phaseolus vulgaris L., Tendergreen) and sweet corn (Zea may var. saccharata (Sturtev.) Bailey, Northrup King 199) were evaluated in greenhouse studies. Plants grew well in fertile Dagor silt loam soil (Cumulic Haploxeroll) when the soil was mixed with most soil-component mixtures at disposal proportions normally expected. Vinyl acetate and maleic acid polymer (VAMA) addition caused significantly increased growth at the 95% confidence level. No statistically significant depression of plant growth occurred at normal rates with asbestos, asphalt, barite, bentonite, calcium lignosulfonate, sodium polyacrylate, a modifiedmore » tannin, ethoxylated nonylphenol, a filming amine, gilsonite, a Xanthan gum, paraformaldehyde, a pipe dope, hydrolized polyacrylamide, sodium acid pyrophosphate, sodium carboxymethyl cellulose, sodium hydroxide added as pellets, and a sulfonated tall oil. Statistically significant reductions in plant yields (at the 95% confidence level) occurred at normal disposal rates with a long-chained aliphatic alcohol, sodium dichromate, diesel oil, guar gum, an iron chromelignosulfonate, lignite, a modified asphalt, a plant fibersynthetic fiber mixture, lignite, a nonfermenting starch, potassium chloride, pregelatinized starch, and sulfated triglyceride. Thirteen drilling fluid components added individually to a fluid base (water, bentonite, and barite) and then to soil were also tested for their effect on plant growth. Only the sulfated triglyceride (Torq-Trim) and the long-chain (high molecular weight) alcohol (Drillaid 405) caused no plant growth reductions at either rate added. The modified tannin (Desco) caused minimal reduction in bean growth only when added to soil in excess levels.« less

Paleocene and Maastrichtian calcareous nannofossils from clasts in Pleistocene glaciomarine muds from the northern James Ross Basin, western Weddell Sea, Antarctica

USGS Publications Warehouse

Kulhanek, D.K.

2007-01-01

Site NBP0602A-9, drilled during the SHALDRIL II cruise of the RV/IB Nathaniel B. Palmer, includes two holes located in the northern James Ross Basin in the western Weddell Sea, very close to the eastern margin of the Antarctic Peninsula. Sediment from both holes consists of very dark grey, pebbly, sandy mud, grading to very dark greenish grey, pebbly, silty mud in the lower 2.5 m of the second hole. In addition to abundant pebbles found throughout the cores, both holes contain numerous sedimentary clasts. Biostratigraphic analysis of diatom assemblages from the glaciomarine muds yields rare to few, poorly preserved diatoms. The mixed assemblage consists mostly of extant species, but also includes reworked taxa that range to the Miocene. The absence of Rouxia spp., however, suggests the sediment is late Pleistocene in age. The sedimentary clasts, on the other hand, are nearly barren of diatoms, but contain rare, moderately to well-preserved calcareous nannofossils. The clasts contain three distinct assemblages. Two clasts are assigned an early Maastrichtian age based on the presence of Biscutum magnum and Nephrolithus corystus, while one clast yields a late Maastrichtian age based on the presence of Nephrolithus frequens. These samples also contain other characteristic Late Cretaceous species, including Biscutum notaculum, Cribrosphaerella daniae, Eiffellithus gorkae, Kamptnerius magnificus, and Prediscosphaera bukryi. Two samples yield an early Paleocene assemblage dominated by Hornibrookina teuriensis. The Maastrichtian assemblages are similar to those found in the López de Bertodano Formation on Seymour and Snow Hill Islands, making it the likely source area for the Cretaceous clast material. Although no calcareous nannofossils have been reported from Paleocene formations on these islands, the occurrence of calcareous foraminifers suggests other calcareous plankton may be present; thus the Paleocene clasts likely also originated from the Seymour Island area.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gavignet, A.A.; Wick, C.J.

In current practice, pressure drops in the mud circulating system and the settling velocity of cuttings are calculated with simple rheological models and simple equations. Wellsite computers now allow more sophistication in drilling computations. In this paper, experimental results on the settling velocity of spheres in drilling fluids are reported, along with rheograms done over a wide range of shear rates. The flow curves are fitted to polynomials and general methods are developed to predict friction losses and settling velocities as functions of the polynomial coefficients. These methods were incorporated in a software package that can handle any rig configurationmore » system, including riser booster. Graphic displays show the effect of each parameter on the performance of the circulating system.« less

Leg 67: the Deep Sea Drilling Project Mid-America Trench transect off Guatemala.

USGS Publications Warehouse

von Huene, Roland E.

1980-01-01

Drilling on the Cocos plate recovered a basal chalk sequence deposited during early and mid-Miocene time, a short interval of abyssal red clay, and an upper sequence of late Miocene and younger sediment deposited within an area influenced by a terrigenous source. In the trench, a mud and sand fill less than 400,000 yr old overlies the oceanic sequence. The entire section shows no evidence of compressive deformation. In contrast, the section cored on the trench's landward slope 3 km from the trench axis is affected by tectonism. The section contains a Cretaceous to Pliocene claystone sequence capped by Pliocene to Quaternary hemipelagic slope deposits.- from Authors

Site 765: Sediment Lithostratigraphy

USGS Publications Warehouse

,

1990-01-01

A 935-m-thick succession of Quaternary through Lower Cretaceous sediments was recovered at Site 765 (Fig. 10). A single core of Quaternary sediment was obtained from Hole 765A; drilling terminated and a new hole was drilled in an attempt to establish the mud line. Quaternary through middle Miocene sediments were cored in Hole 765B down to a depth of 395.6 mbsf. Middle Miocene through Lower Cretaceous sediments were cored in Hole 765C, after washing the interval between 0 and 350.2 mbsf. Exact lithologic correlation of the basal cores from Hole 765B with the upper cores from Hole 765C is not possible because of poor recovery; hence, correlation is based solely on matching sub-bottom depths.

Use of inorganic and organic wastes for in situ immobilisation of Pb and Zn in a contaminated alkaline soil.

PubMed

Zhou, Y-F; Haynes, R J; Naidu, R

2012-05-01

This study aims to examine whether addition of immobilising agents to a sandy, alkaline (pH = 8.1) soil, which had been contaminated with Pb and Zn by airborne particles from a Pb/Zn smelter, would substantially reduce metal bioavailability. The effectiveness of five waste materials (blast furnace (BF) slag, alum water treatment (WT) sludge, red mud, sugar mill mud and green waste compost) as metal immobilising agents was evaluated by incubating them with a contaminated soil for a period of 12 months at rates of 5% and 10% (w/w), after which, Rhodes grass was grown in the soils in a greenhouse study. Additions of WT sludge, BF slag and red mud reduced CaCl(2), CH(3)COOH, HCl and EDTA-extractable Zn but compost and mill mud had no appreciable immobilising effects. Additions of all amendments reduced levels of CaCl(2), CH(3)COOH and HCl-extractable Pb although concentrations of EDTA-extractable Pb remained unchanged. A sequential extraction procedure showed that additions of mill mud and compost increased the percentage of total Pb and Zn present in the oxidisable fraction whilst additions of the other materials increased the percentage present in the residual fraction. Rhodes grass yields were promoted greatly by additions of red mud, compost and particularly mill mud, and yields were negatively correlated with tissue Pb concentrations and extractable Pb. Red mud was the most effective material for lowering extractable Pb and Zn levels simultaneously while mill mud and compost were notably effective for Pb. A field evaluation in the study area is justified.

Stability analysis of coupled torsional vibration and pressure in oilwell drillstring system

NASA Astrophysics Data System (ADS)

Toumi, S.; Beji, L.; Mlayeh, R.; Abichou, A.

2018-01-01

To address security issues in oilwell drillstring system, the drilling operation handling which is in generally not autonomous but ensured by an operator may be drill bit destructive or fatal for the machine. To control of stick-slip phenomenon, the drillstring control at the right speed taking only the drillstring vibration is not sufficient as the mud dynamics and the pressure change around the drill pipes cannot be neglected. A coupled torsional vibration and pressure model is presented, and the well-posedness problem is addressed. As a Partial Differential Equation-Ordinary Differential Equation (PDE-ODE) coupled system, and in order to maintain a non destructive downhole pressure, we investigate the control stability with and without the damping term in the wave PDE. In terms of, the torsional variable, the downhole pressure, and the annulus pressure, the coupled system equilibrium is shown to be exponentially stable.

Development of improved high temperature seals and lubricants for downhole motors in geothermal applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

De La Fosse, P.H.; Black, A.D.; DiBona, B.G.

1983-01-01

A major limitation of downhole mud motors for geothermal drilling, as well as straight-hole oil and gas drilling, is the bearing section. Reduced bearing life results from the inability to seal a lubricant in the bearing pack. A reliable rotary seal will extend the bearing life and will allow high pressure drops across the bit for improved bottomhole cleaning and increased drilling rate. This paper summarizes the results of a six-year program funded by the U.S. Department of Energy/Division of Geothermal Energy to develop a sealed bearing pack for use with downhole motors in geothermal applications. Descriptions of the Sealmore » Test Machine, Lubricant Test Machine and Bearing Pack Test Facility are presented. Summaries of all seal tests, lubricant tests and bearing pack tests are provided; and a comprehensive program bibliography is presented.« less

Real-Time Fluid and Gas Monitoring During Drilling of the SAFOD Main Hole in Parkfield, CA.

NASA Astrophysics Data System (ADS)

Wiersberg, T.; Erzinger, J.

2005-12-01

Little is known about the role and origin of fluids and gases associated with the San Andreas Fault zone (SAF). To gain information on fluids and gases at depth, we performed real-time mud gas monitoring during drilling of the SAFOD (San Andreas Fault Observatory at Depth) Pilot Hole (PH) and Main Hole (MH). Gas extracted from returning drill mud was piped into a nearby laboratory trailer and analyzed on-line. Permanent gases were detected using a portable mass spectrometer, hydrocarbons with a gas chromatograph, and the 222Rn-activity with a Lucas-Cell detector. When significant amounts of non-atmospheric gases were detected, off-line gas samples were collected from the gas line for further isotope studies. The SAFOD PH and MH were drilled in only a few meter distance, but in contrast to the straight PH, which penetrates through 768 m of sediments into granites down to 2168 m target depth (TD), the nearby MH is deviated towards the SAF and returns into sedimentary strata below 1930 m. The MH drilled sedimentary rocks down to 3987 m TD, approximately 45 m northeast of the surface trace of the SAF. From surface to 1930 m, the depth distribution of gas is similar for SAFOD PH and MH. Shear zones, identified by geophysical logging, are often characterized by elevated concentrations of CH4, CO2, H2, Rn, and He. The same gases were found in the MH below 1930 m, but their concentrations were, with the exception of He, significantly higher: CH4, CO2, and H2 sometimes reach several volume percent. Generally, the gas composition is partly controlled by the lithology. Variation in the methane concentration in several depth intervals reflects the changes in lithology from low gas abundance in clays and silts to more gas rich shales, which are the source rocks for hydrocarbons. Highly porous and permeable sandstone yield the highest concentrations of hydrocarbons (up to 15 vol% methane), and may be regarded as reservoir rocks. We interpret high radon activities in mud gas as indicator for circulating fluids entering the borehole via fractures. These fluids are also rich in hydrocarbons, carbon dioxide, and hydrogen, but only low concentrated in helium. Such intervals could be identified in several depth intervals (2675-2750 m, 2825-2900 m, and 3550-3650 m depth, and below 3700 m). The hydrocarbons in the surrounding rocks show a similar composition as those associated with fault zones. In addition to the low helium concentration, these results demonstrate fluid migration from the nearby with only little evidence for gas migration from a deeper source. A striking observation is the high amount of hydrogen found in these intervals. We can exclude a significant contribution of artificial hydrogen (drilling artifact) and mantle hydrogen. From soil gas studies, it is known that fault zones sometimes show enhanced concentration of hydrogen. As a possible source of hydrogen, the interaction of water with freshly ground rock, caused by fault zone movement, is discussed. Isotopic studies on hydrogen in combination with laboratory experiments are ongoing to test hydrogen synthesis by rock-water interaction. First isotopic studies on δ13C of methane indicate mixing of microbial methane with only small amounts of methane generated by thermal degradation of organic matter in the shallower depth (down to ~2500 m). Below this depth, the concentration of heavy hydrocarbons increases. CH4/(C2H6+C3H8) significantly drops from >100 to values <30 towards the bottom of the MH, and, methane becomes isotopically heavier, which is more typical for thermogenic hydrocarbons.

Seismic stratigraphy of the Heuksan mud belt in the southeastern Yellow Sea, Korea

NASA Astrophysics Data System (ADS)

Lee, Gwang-Soo; Yoo, Dong Geun; Bae, Sung Ho; Min, Gun-Hong; Kim, Seong-Pil; Choi, Hunsoo

2015-12-01

To establish the seismic stratigraphy of the Heuksan mud belt (HMB) and reconstruct its depositional history, approximately 1,600 km of high-resolution seismic data were newly obtained using chirp acoustic sub-bottom profiler, sparker, and air-gun seismic systems. Based on seismic stratigraphic analysis, the HMB can be divided into three major seismic units (I, II, and III, from top to bottom) and four subunits (II-a, II-b, III-a, and III-b) overlying transgressive sands, pre-last glacial maximum (LGM) deposits, and the acoustic basement. Each unit and subunit show different seismic facies and geometry, being clearly separated from each other by bounding surfaces formed since the LGM. The spatial distribution, thicknesses and volumes of the seismic units were determined and plotted to document the sequential formation of the HMB. The correlation between deep drill core data (HMB-101, HMB-102, HMB-103, YSDP-101, and YSDP-102) and the seismic data suggests that subunits III-b and III-a were formed by the continuous accumulation of fine-grained sediment with partial sandy sediment in an estuarine/deltaic environment during the early to middle transgressive stage, accompanied by landward migration of the shoreline. Subunits II-b and II-a were probably formed by re-deposition of large volumes of sediment eroded from unit III during the middle transgressive to early highstand stage. Unit I is interpreted as the most recent mud deposit representing the highstand systems tract when sea-level rise terminated. The careful definition of seismic units and their interpretation proposed in this study, on the basis of the large and partly new seismic dataset covering the entire HMB together with deep drill core data, have been instrumental in reconstructing the depositional environment and formation mechanisms of the HMB.

Recycling of red muds with the extraction of metals and special additions to cement

NASA Astrophysics Data System (ADS)

Zinoveev, D. V.; Diubanov, V. G.; Shutova, A. V.; Ziniaeva, M. V.

2015-01-01

The liquid-phase reduction of iron oxides from red mud is experimentally studied. It is shown that, in addition to a metal, a slag suitable for utilization in the construction industry can be produced as a result of pyrometallurgical processing of red mud. Portland cement is shown to be produced from this slag with mineral additions and a high-aluminate expansion addition to cement.

Seismic While Drilling Case Study in Shengli Oilfield, Eastern China

NASA Astrophysics Data System (ADS)

Wang, L.; Liu, H.; Tong, S.; Zou, Z.

2015-12-01

Seismic while drilling (SWD) is a promising borehole seismic technique with reduction of drilling risk, cost savings and increased efficiency. To evaluate the technical and economic benefits of this new technique, we carried out SWD survey at well G130 in Shengli Oilfield of Eastern China. Well G130 is an evaluation well, located in Dongying depression at depth more than 3500m. We used an array of portable seismometers to record the surface SWD-data, during the whole drilling progress. The pilot signal was being recorded continuously, by an accelerometer mounted on the top of the drill string. There were also two seismometers buried in the drill yard, one near diesel engine and another near derrick. All the data was being recorded continuously. According to mud logging data, we have processed and analyzed all the data. It demonstrates the drill yard noise is the primary noise among the whole surface wavefield and its dominant frequency is about 20Hz. Crosscorrelation of surface signal with the pilot signal shows its SNR is severely low and there is no any obvious event of drill-bit signals. Fortunately, the autocorrelation of the pilot signal shows clear BHA multiple and drill string multiple. The period of drill string multiple can be used for establishing the reference time (so-called zero time). We identified and removed different noises from the surface SWD-data, taking advantages of wavefield analysis. The drill-bit signal was retrieved from surface SWD-data, using seismic interferometry. And a reverse vertical seismic profile (RVSP) data set for the continuous drilling depth was established. The subsurface images derived from these data compare well with the corresponding images of 3D surface seismic survey cross the well.

Antiwhirl PDC bits increased penetration rates in Alberta drilling. [Polycrystalline Diamond Compact

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bobrosky, D.; Osmak, G.

1993-07-05

The antiwhirl PDC bits and an inhibitive mud system contributed to the quicker drilling of the time-sensitive shales. The hole washouts in the intermediate section were dramatically reduced, resulting in better intermediate casing cement jobs. Also, the use of antirotation PDC-drillable cementing plugs eliminated the need to drill out plugs and float equipment with a steel tooth bit and then trip for the PDC bit. By using an antiwhirl PDC bit, at least one trip was eliminated in the intermediate section. Offset data indicated that two to six conventional bits would have been required to drill the intermediate hole interval.more » The PDC bit was rebuildable and therefore rerunnable even after being used on five wells. In each instance, the cost of replacing chipped cutters was less than the cost of a new insert roller cone bit. The paper describes the antiwhirl bits; the development of the bits; and their application in a clastic sequence, a carbonate sequence, and the Shekilie oil field; the improvement in the rate of penetration; the selection of bottom hole assemblies; washout problems; and drill-out characteristics.« less

Toxicity assessment in marine sediment for the Terra Nova environmental effects monitoring program (1997-2010)

NASA Astrophysics Data System (ADS)

Whiteway, Sandra A.; Paine, Michael D.; Wells, Trudy A.; DeBlois, Elisabeth M.; Kilgour, Bruce W.; Tracy, Ellen; Crowley, Roger D.; Williams, Urban P.; Janes, G. Gregory

2014-12-01

This paper discusses toxicity test results on sediments from the Terra Nova offshore oil development. The Terra Nova Field is located on the Grand Banks approximately 350 km southeast of Newfoundland (Canada). The amphipod (Rhepoxynius abronius) survival and solid phase luminescent bacteria (Vibrio fischeri, or Microtox) assays were conducted on sediment samples collected from approximately 50 stations per program year around Terra Nova during baseline (1997), prior to drilling, and in 2000, 2001, 2002, 2004, 2006, 2008 and 2010 after drilling began. The frequency of toxic responses in the amphipod toxicity test was low. Of the ten stations that were toxic in environmental effects monitoring (EEM) years, only one (station 30(FE)) was toxic in more than one year and could be directly attributed to Terra Nova project activities. In contrast, 65 (18%) of 364 EEM samples were toxic to Microtox. Microtox toxicity in EEM years was not related to distance from Terra Nova drill centres or concentrations of >C10-C21 hydrocarbons or barium, the primary constituents of the synthetic-based drill muds used at Terra Nova. Of the variables tested, fines and strontium levels showed the strongest (positive) correlations with toxicity. Neither fines nor strontium levels were affected by drill cuttings discharge at Terra Nova, except at station 30(FE) (and that station was not toxic to Microtox). Benthic macro-invertebrate abundance, richness and diversity were greater in toxic than in non-toxic sediments. Therefore, Microtox responses indicating toxicity were associated with positive biological responses in the field. This result may have been an indirect function of the increased abundance of most invertebrate taxa in less sandy sediments with higher gravel content, where fines and strontium levels and, consequently, toxicity to Microtox were high; or chemical substances released by biodegradation of organic matter, where invertebrates are abundant, may be toxic to Microtox. Given the lack of association between Microtox results and discharge from Terra Nova, coupled with the confounding effects of other variables, the usefulness of Microtox toxicity tests within the context of environmental monitoring for the Terra Nova and, potentially, other offshore oil operations needs to be questioned. The amphipod toxicity tests showed that sediments in the vicinity of discharges of synthetic-based drilling mud cuttings are rarely toxic.

Pressure-Letdown Machine for a Coal Reactor

NASA Technical Reports Server (NTRS)

Perkins, G. S.; Mabe, W. B.

1986-01-01

Pumps operating in reverse generate power. Conceptual pressure-letdown machine for coal-liquefaction system extracts energy from expansion of product fluid. Mud pumps, originally intended for use in oil drilling, operated in reverse so their motors act as generators. Several pumps operated in alternating phase to obtain multiple stages of letdown from inlet pressure to outlet pressure. About 75 percent of work generates inlet pressure recoverable as electrical energy.

Bore pile foundation tall buildings closed in the heritage building

NASA Astrophysics Data System (ADS)

Triastuti, Nusa Setiani

2017-11-01

Bore pile foundation for high building surroundings heritage building should be not damage. Construction proses must good, no necking, no mixed deep water, no sliding soil, nonporous concrete. Objective the execution of bore pile so that heritage buildings and neighboring buildings that are old do not experience cracks, damage and tilting. The survey methodology was observe the process of the implementation of the dominant silt, clay soil, in addition a limited space and to analyze the results of loading tests, investigations of soil and daily reports. Construction process determines the success of the structure bore pile in high building structure bearing, without damaging a heritage building. Attainment the hard soil depth, density concrete, observable clean reinforcement in the implementation. Monitoring the implementation of, among others, the face of the ground water little reduce in the area and outside the footprint of the building, no impact of vibration drilling equipment, watching the mud content on the water coming out at the time of drilling, concrete volume was monitored each 2 m bore depth of pile, The result researched heritage building was not damage. The test results bore pile axial, lateral analyzed the results have the appropriate force design required.

Abandoned coal mine stores gas for Colorado peak-day demands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, L.W.

1978-09-01

Since 1961, the Leyden Mine, from which 6 million tons of coal had been removed to leave a 150 million cu ft void, has been used for gas storage at 250 psig max pressure, after the hoisting and ventilation shafts had been sealed with concrete, rock, sand, and mud. Following several withdrawal expansions, a design for maximum delivery of 230 million cu ft/day for five days with a pressure drop in the cavern down to 100 psig was developed to satisfy customer requirements for peak shaving. This required redesigning the gathering system by looping large existing lines, eliminating inefficient ones,more » and drilling additional wells; installing three lightweight 3500-hp Centaur turbine/compressor units from Solar Turbines International to provide the minimum 200 psig compressor discharge pressure needed for gas distribution on peak usage days; and installing Donaldson Co. engine air-inlet silencers on the turbine inlets to reduce noise levels below the public code requirement. In the 1977-78 heating season, the Leyden facility produced 196 million cu ft/day of gas; with continued load growth and well drilling to reduce pressure loss, the maximum design flow rate will be attained.« less

Summary: High Temperature Downhole Motor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raymond, David W.

2017-10-01

Directional drilling can be used to enable multi-lateral completions from a single well pad to improve well productivity and decrease environmental impact. Downhole rotation is typically developed with a motor in the Bottom Hole Assembly (BHA) that develops drilling power (speed and torque) necessary to drive rock reduction mechanisms (i.e., the bit) apart from the rotation developed by the surface rig. Historically, wellbore deviation has been introduced by a “bent-sub,” located in the BHA, that introduces a small angular deviation, typically less than 3 degrees, to allow the bit to drill off-axis with orientation of the BHA controlled at themore » surface. The development of a high temperature downhole motor would allow reliable use of bent subs for geothermal directional drilling. Sandia National Laboratories is pursuing the development of a high temperature motor that will operate on either drilling fluid (water-based mud) or compressed air to enable drilling high temperature, high strength, fractured rock. The project consists of designing a power section based upon geothermal drilling requirements; modeling and analysis of potential solutions; and design, development and testing of prototype hardware to validate the concept. Drilling costs contribute substantially to geothermal electricity production costs. The present development will result in more reliable access to deep, hot geothermal resources and allow preferential wellbore trajectories to be achieved. This will enable development of geothermal wells with multi-lateral completions resulting in improved geothermal resource recovery, decreased environmental impact and enhanced well construction economics.« less

An interactive drilling simulator for teaching and research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, G.A.; Cooper, A.G.; Bihn, G.

1995-12-31

An interactive program has been constructed that allows a student or engineer to simulate the drilling of an oil well, and to optimize the drilling process by comparing different drilling plans. The program operates in a very user-friendly way, with emphasis on menu and button-driven commands. The simulator may be run either as a training program, with exercises that illustrate various features of the drilling process, as a game, in which a student is set a challenge to drill a well with minimum cost or time under constraints set by an instructor, or as a simulator of a real situationmore » to investigate the merit of different drilling strategies. It has three main parts, a Lithology Editor, a Settings Editor and the simulation program itself. The Lithology Editor allows the student, instructor or engineer to build a real or imaginary sequence of rock layers, each characterized by its mineralogy, drilling and log responses. The Settings Editor allows the definition of all the operational parameters, ranging from the drilling and wear rates of particular bits in specified rocks to the costs of different procedures. The simulator itself contains an algorithm that determines rate of penetration and rate of wear of the bit as drilling continues. It also determines whether the well kicks or fractures, and assigns various other {open_quotes}accident{close_quotes} conditions. During operation, a depth vs. time curve is displayed, together with a {open_quotes}mud log{close_quotes} showing the rock layers penetrated. If desired, the well may be {open_quotes}logged{close_quotes} casings may be set and pore and fracture pressure gradients may be displayed. During drilling, the total time and cost are shown, together with cost per foot in total and for the current bit run.« less

Study on dealkalization and settling performance of red mud.

PubMed

Luo, Muxi; Qi, Xuejiao; Zhang, Yurui; Ren, Yufei; Tong, Jiacheng; Chen, Zining; Hou, Yiming; Yeerkebai, Nuerxiate; Wang, Hongtao; Feng, Shijin; Li, Fengting

2017-01-01

At present, the dealkalization and comprehensive utilization of red mud is a worldwide problem. Studies on the settling performance and phase transformation of red mud by HCl, CaO, and H 2 O leaching are limited. In this study, the characteristics of red mud were systematically analyzed. The average sizes of graded and initial red mud were 4.11 and 9.20 μm, respectively. X-ray diffraction (XRD), X-ray fluorescence spectra (XRF), and thermogravimetry-differential scanning calorimetry (TG-DSC) results indicated the different mineralogical phases, composition, and thermal behavior. The addition of HCl could neutralize the alkalization in the red mud slurry, and CaO could replace the Na and K. Notably, the pH of the red mud slurry had no obvious change with the increase in water washing times in a certain pH. Interestingly, soluble Al and Fe were not detected in the HCl-red mud and CaO-red mud. In addition, the settling ratio was used to express the settling performance of the red mud slurry. Their interaction mechanisms were proposed, which may include phase transformation and the changing of the size and surface area. The research provided a better understanding of the phase transformation and settling performance in the treatment of red mud by HCl, CaO, and H 2 O leaching.

Smaller Footprint Drilling System for Deep and Hard Rock Environments; Feasibility of Ultra-High-Speed Diamond Drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

TerraTek, A Schlumberger Company

2008-12-31

The two phase program addresses long-term developments in deep well and hard rock drilling. TerraTek believes that significant improvements in drilling deep hard rock will be obtained by applying ultra-high rotational speeds (greater than 10,000 rpm). The work includes a feasibility of concept research effort aimed at development that will ultimately result in the ability to reliably drill 'faster and deeper' possibly with smaller, more mobile rigs. The principle focus is on demonstration testing of diamond bits rotating at speeds in excess of 10,000 rpm to achieve high rate of penetration (ROP) rock cutting with substantially lower inputs of energymore » and loads. The significance of the 'ultra-high rotary speed drilling system' is the ability to drill into rock at very low weights on bit and possibly lower energy levels. The drilling and coring industry today does not practice this technology. The highest rotary speed systems in oil field and mining drilling and coring today run less than 10,000 rpm - usually well below 5,000 rpm. This document provides the progress through two phases of the program entitled 'Smaller Footprint Drilling System for Deep and Hard Rock Environments: Feasibility of Ultra-High-Speed Diamond Drilling' for the period starting 30 June 2003 and concluding 31 March 2009. The accomplishments of Phases 1 and 2 are summarized as follows: (1) TerraTek reviewed applicable literature and documentation and convened a project kick-off meeting with Industry Advisors in attendance (see Black and Judzis); (2) TerraTek designed and planned Phase I bench scale experiments (See Black and Judzis). Improvements were made to the loading mechanism and the rotational speed monitoring instrumentation. New drill bit designs were developed to provided a more consistent product with consistent performance. A test matrix for the final core bit testing program was completed; (3) TerraTek concluded small-scale cutting performance tests; (4) Analysis of Phase 1 data indicated that there is decreased specific energy as the rotational speed increases; (5) Technology transfer, as part of Phase 1, was accomplished with technical presentations to the industry (see Judzis, Boucher, McCammon, and Black); (6) TerraTek prepared a design concept for the high speed drilling test stand, which was planned around the proposed high speed mud motor concept. Alternative drives for the test stand were explored; a high speed hydraulic motor concept was finally used; (7) The high speed system was modified to accommodate larger drill bits than originally planned; (8) Prototype mud turbine motors and the high speed test stand were used to drive the drill bits at high speed; (9) Three different rock types were used during the testing: Sierra White granite, Crab Orchard sandstone, and Colton sandstone. The drill bits used included diamond impregnated bits, a polycrystalline diamond compact (PDC) bit, a thermally stable PDC (TSP) bit, and a hybrid TSP and natural diamond bit; and (10) The drill bits were run at rotary speeds up to 5500 rpm and weight on bit (WOB) to 8000 lbf. During Phase 2, the ROP as measured in depth of cut per bit revolution generally increased with increased WOB. The performance was mixed with increased rotary speed, with the depth cut with the impregnated drill bit generally increasing and the TSP and hybrid TSP drill bits generally decreasing. The ROP in ft/hr generally increased with all bits with increased WOB and rotary speed. The mechanical specific energy generally improved (decreased) with increased WOB and was mixed with increased rotary speed.« less

Red mud as a carbon sink: variability, affecting factors and environmental significance.

PubMed

Si, Chunhua; Ma, Yingqun; Lin, Chuxia

2013-01-15

The capacity of red mud to sequester CO(2) varied markedly due to differences in bauxite type, processing and disposal methods. Calcium carbonates were the dominant mineral phases responsible for the carbon sequestration in the investigated red mud types. The carbon sequestration capacity of red mud was not fully exploited due to shortages of soluble divalent cations for formation of stable carbonate minerals. Titanate and silicate ions were the two major oxyanions that appeared to strongly compete with carbonate ions for the available soluble Ca. Supply of additional soluble Ca and Mg could be a viable pathway for maximizing carbon sequestration in red mud and simultaneously reducing the causticity of red mud. It is roughly estimated that over 100 million tonnes of CO(2) have been unintentionally sequestered in red mud around the world to date through the natural weathering of historically produced red mud. Based on the current production rate of red mud, it is likely that some 6 million tonnes of CO(2) will be sequestered annually through atmospheric carbonation. If appropriate technologies are in place for incorporating binding cations into red mud, approximately 6 million tonnes of additional CO(2) can be captured and stored in the red mud while the hazardousness of red mud is simultaneously reduced. Copyright © 2012 Elsevier B.V. All rights reserved.

FORGE Milford Digitized Geophysical Logs from Acord 1

DOE Data Explorer

Jones, Clay G.; Moore, Joseph N.

2016-03-31

This submission includes digitalized versions of the following: McCulloch Geothermal Corp Acord 1-26 Cover Letter McCulloch Geothermal Corp Acord 1-26 Drilling Plan McCulloch Geothermal Corp Acord 1-26 Bond Documents Division of Water Rights Permission to Drill Drillers Log Geothermal Data (Mud) Log Compensated Densilog - Neutron Log Dual Induction Focused Log BHC Acoustilog Differential Temperature Log Dual Induction Focused Log Gamma Ray Neutron Log Temperature Log Caliper Temperature Log (Run 3) Densilog Gamma Ray Neutron Log Temperature Log (Run 4) Compensated Densilog Sample Log (Page 1 of 2) Report of Well Driller Stratigraphic Report (J.E. Welsh) Photographs and Negatives of Acord 1-26 Well Site (7) Petrography Report (M.J. Sweeney) Cuttings Samples (21 Boxes at Utah Core Research Center)

Optimizing Geothermal Drilling: Oil and Gas Technology Transfer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denninger, Kate; Eustes, Alfred; Visser, Charles

There is a significant amount of financial risk associated with geothermal drilling. This study of drilling operations seeks opportunities to improve upon current practices and technologies. The scope of this study included analyzing 21 geothermal wells and 21 oil and gas wells. The goal was to determine a 'Perfect Well' using historical data to compare the best oil and gas well to the best geothermal well. Unfortunately, limitations encountered in the study included missing data (bit records, mud information, etc.) and poor data collection practices An online software database was used to format drilling data to IADC coded daily drillingmore » reports and generate figures for analysis. Six major issues have been found in geothermal drilling operations. These problems include lost circulation, rig/ equipment selection, cementing, penetration rate, drilling program, and time management. As a result of these issues, geothermal drilling averaged 56.4 days longer than drilling comparable oil and gas wells in the wells in this study. Roughly $13.9 million was spent on non-productive time in the 21 geothermal wells, compared with only $1.3 million in the oil and gas wells, assuming a cost of $50,000 per day. Comparable events such as drilling the same sized hole, tripping in/out, cementing, and running the same size casing took substantially less time in the oil and gas wells. Geothermal wells were drilled using older and/or less advanced technology to depths less than 10,000 feet, while oil and gas wells reached 12,500 feet faster with purpose built rigs. A new approach is now underway that will optimize drilling programs throughout the drilling industry using Mechanical Specific Energy (MSE) as a tool to realize efficient drilling processes. Potential improvements for current geothermal operations are: the use of electronic records, real time services, and official glossary terms to describe rig operations, and advanced drilling rigs/technology.« less

Microwave/Sonic Apparatus Measures Flow and Density in Pipe

NASA Technical Reports Server (NTRS)

Arndt, G. D.; Ngo, Phong; Carl, J. R.; Byerly, Kent A.

2004-01-01

An apparatus for measuring the rate of flow and the mass density of a liquid or slurry includes a special section of pipe instrumented with microwave and sonic sensors, and a computer that processes digitized readings taken by the sensors. The apparatus was conceived specifically for monitoring a flow of oil-well-drilling mud, but the basic principles of its design and operation are also applicable to monitoring flows of other liquids and slurries.

Hidden values in bauxite residue (red mud): recovery of metals.

PubMed

Liu, Yanju; Naidu, Ravi

2014-12-01

Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud. Copyright © 2014 Elsevier Ltd. All rights reserved.

Overview of SAFOD Phases 1 and 2: Drilling, Sampling and Measurements in the San Andreas Fault Zone at Seismogenic Depth

NASA Astrophysics Data System (ADS)

Zoback, M. D.; Hickman, S.; Ellsworth, W.

2005-12-01

In this talk we provide an overview of on-site drilling, sampling and downhole measurement activities associated with the first two Phases of the San Andreas Fault Observatory at Depth. SAFOD is located at the transition between the creeping and locked sections of the fault, 9 km NW of Parkfield, CA. A 2.1 km deep vertical pilot hole was drilled at the site in 2002. The SAFOD main borehole was drilled vertically to a depth of 1.5 km and then deviated at an average angle of 55° to vertical, passing beneath the surface trace of the San Andreas fault, 1.8 km to the NW at a depth of 3.2 km. Repeating microearthquakes on the San Andreas define the main active fault trace at depth, as well as a secondary active fault about 250 m to the SW (i.e., closer to SAFOD). The hole was rotary drilled, comprehensive cuttings were obtained and a real-time analysis of gases in the drilling mud was carried out. Spot cores were obtained at three depths (at casing set points) in the shallow granite and deeper sedimentary rocks penetrated by the hole, augmented by over fifty side-wall cores. Continuous coring of the San Andreas Fault Zone will be carried out in Phase 3 of the project in the summer of 2007. In addition to sampling mud gas, discrete fluid and gas samples were obtained at several depths for geochemical analysis. Real-time geophysical measurements were made while drilling through most of the San Andreas Fault Zone. A suite of "open hole" geophysical measurements were also made over essentially the entire depth of the hole. Construction of the multi-component SAFOD observatory is well underway, with a seismometer and tiltmeter operating at 1 km depth in the pilot hole and a fiber-optic laser strainmeter cemented behind casing in the main hole. A seismometer deployed at depth in the hole between Phases 1 and 2 detected one of the target earthquakes. A number of surface-to-borehole seismic experiments have been carried out to characterize seismic velocities and structures at depth, including deployment of an 80-level, 240-component seismic array in SAFOD in the spring of 2005. With knowledge of P- and S-wave velocities obtained from the geophysical measurements in conjunction with downhole recordings of the SAFOD target earthquake, it appears that the seismically active main trace of the fault is on the order of 400 m SW of the surface trace, in proximity to several candidate zones of particularly anomalous geophysical properties. Observations of casing deformation to be made over the next several years, as well as monitoring of the microearthquakes using seismometers directly within the fault zone, will pinpoint the exact location of this and other active fault traces prior to continuous coring in Phase 3. As will be elaborated in detail by the presentations of the SAFOD science team at this meeting, the activities carried out as part of Phases 1 and 2 of SAFOD lay the ground work for years of exciting research in earthquake physics, fault-rock geology, rock mechanics and the role of fluids and gases in faulting and earthquake generation.

Hidden values in bauxite residue (red mud): Recovery of metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Yanju; Naidu, Ravi, E-mail: ravi.naidu@unisa.edu.au

Highlights: • Current iron recovery techniques using red mud are depicted. • Advantages and disadvantages exist in different recovering processes. • Economic and environmental friendly integrated usage of red mud is promising. - Abstract: Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially.more » Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud.« less

Examination of body burden and taint for Iceland scallop (Chlamys islandica) and American plaice (Hippoglossoides platessoides) near the Terra Nova offshore oil development over ten years of drilling on the Grand Banks of Newfoundland, Canada

NASA Astrophysics Data System (ADS)

DeBlois, Elisabeth M.; Kiceniuk, Joe W.; Paine, Michael D.; Kilgour, Bruce W.; Tracy, Ellen; Crowley, Roger D.; Williams, Urban P.; Gregory Janes, G.

2014-12-01

This paper presents results of analyses of body burdens of metals and hydrocarbons, and taste tests for taint, in Iceland scallop and American plaice performed as part of the Environmental Effects Monitoring (EEM) program for the Terra Nova offshore oil development (Grand Banks of Newfoundland, Canada). Scallop and plaice were collected in a Study Area located within approximately 1 km of drill centres at Terra Nova and in a Reference Area located approximately 20 km from the development. Samples were collected in 1997 to establish a baseline, and from 2000 to 2010, during drilling periods. Scallop adductor muscle tissue was contaminated with >C10-C21 aliphatic hydrocarbons resembling the drilling fluid in the synthetic drilling mud (SBM) used at Terra Nova in 2000, 2002 and 2004, but contamination of adductor muscle was not noted in 2006, 2008 and 2010. The maximum concentration in muscle was 28 mg/kg wet weight, noted in 2002. Scallop viscera was contaminated with hydrocarbons resembling drilling fluid in SBMs near drill centres in all EEM years except 2010. Viscera contamination with >C10-C21 hydrocarbons gradually decreased from a maximum of 150 mg/kg in 2000, to a maximum of 27 mg/kg in 2008; all values were below the laboratory reporting detection limit of 15 mg/kg in 2010. Therefore, evidence from both muscle and viscera indicates a decrease in tissue hydrocarbon contamination in recent years. Barium, another major constituent in drilling muds, has not been noted in scallop adductor muscles at concentrations above the reporting detection limit, but barium was detected in viscera in baseline and EEM years. The maximum concentration of barium in viscera during baseline sampling was 8 mg/kg. The maximum concentration in EEM years (29 mg/kg) was noted in 2000. The maximum concentration in 2010 was 25 mg/kg. The concentration of metals other than barium in scallop tissues was similar between the Terra Nova Study Area and the Reference Area. Hydrocarbons resembling the fluid in SBMs were noted in one American plaice liver sample collected near drill centres in 2000. Otherwise, there has been no evidence of project-related metals or hydrocarbon contamination in plaice liver or fillet samples. There has been no evidence of taint (off-taste) for scallop adductor muscle and plaice fillet tissue in baseline or EEM years. Combined with a parallel study on fish bioindicators at Terra Nova that showed that fish health at Terra Nova was similar to that at the Reference Area (Mathieu et al., 2011), these results indicate little to no detectable biological effects on Iceland scallop and American plaice as a result of Terra Nova activities.

Final report on evaluation of cyclocraft support of oil and gas operations in wetland areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eggington, W.J.; Stevens, P.M.; John, C.J.

1994-10-01

The cyclocraft is a proven hybrid aircraft, capable of VTOL, lifting heavy and bulky loads, highly controllable, having high safety characteristics and low operating costs. Mission Research Corporation (MRC), under Department of Energy sponsorship, is evaluating the potential use of cyclocraft in the transport of drill rigs, mud, pipes and other materials and equipment, in a cost effective and environmentally safe manner, to support oil and gas drilling, production, and transportation operations in wetland areas. Based upon the results of an earlier parametric study, a cyclocraft design, having a payload capacity of 45 tons and designated H.1 Cyclocraft, was selectedmore » for further study, including the preparation of a preliminary design and a development plan, and the determination of operating costs. This report contains all of the results derived from the program to evaluate the use of cyclocraft in the support of oil and gas drilling and production operations in wetland areas.« less

Direct Observations of In Situ Stress State in a 3 Kilometer Deep Borehole in the Upper Plate, Nankai Trough Subduction Zone: IODP Site C0002

NASA Astrophysics Data System (ADS)

Tobin, H. J.; Saffer, D. M.; Castillo, D. A.; Hirose, T.

2016-12-01

During IODP Expedition 348, borehole C0002F/N/P was advanced to a depth of 3058 m below the seafloor (mbsf) into the inner forearc accretionary wedge of the Nankai subduction zone (SW Japan), now the deepest scientific drilling ever into the ocean floor. The goals were to investigate the physical properties, structure, and state of stress deep within the hanging wall of a seismogenic subduction plate boundary. Mud pressure and gas monitoring, injection tests, leak-off tests (LOT), logging-while-drilling (LWD) measurements, and observations of mud losses and hole conditions provide both direct and indirect information about in situ pore pressure and stress state. The LOTs show that the minimum principal stress is consistently less than the vertical stress defined by the overburden, ruling out a thrust faulting stress state throughout the drilled section, and define a nearly linear gradient in Shmin from the seafloor to the base of the hole. Observations of mud loss and the lack of observed gas shows indicate that formation pore fluid pressure is not significantly (< 10 MPa) greater than hydrostatic. The maximum horizontal stress, estimated from borehole breakout width and pressure spikes during pack-off events, is close in magnitude to the vertical stress. Therefore the accretionary prism lies in either a normal or strike-slip faulting regime, or is transitional between the two, from 1 to 3 km depth. At 3002 mbsf we estimate that the effective stresses are: Sv' = 33 MPa; SHmax' = 25-36 MPa; and Shmin' = 18.5-21 MPa. Differential stresses are therefore low, on the order of 10-12 MPa, in the hanging wall of the subduction thrust. We conclude that (1) the inner wedge is not critically stressed in horizontal compression; (2) basal traction along the megathrust must be low in order to permit concurrent locking of the fault and low differential stresses deep within the upper plate; and (3) although low differential stresses may persist down to the plate boundary at 5000 mbsf, the maximum horizontal stress SHmax must transition to become greater than the vertical stress, either spatially below the base of the borehole, or temporally leading up to megathrust fault rupture, in order to drive slip on the megathrust.

Molt-related susceptibility and regenerative limb growth as sensitive indicators of aquatic pollutant toxicity to crustaceans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rao, K.R.; Conklin, P.J.

1986-01-01

The study evaluated the comparative toxicity of various pollutants to intermolt and molting grass shrimp (Palaemonetes pugio). Most of the tested materials (pentachlorophenol, tetrachlorophenols, trichlorophenols, methylenebis dichlorophenol, dibutyl phthalate, chromium, and drilling mud) were more toxic to molting shrimp than to intermolt shrimp. Radio-tracer studies with 2,4,5-trichlorophenol and pentachlorophenol indicated that the increased susceptibility of newly molted shrimp is linked to increased pollutant uptake.

The Chesapeake Bay Impact Crater: An Educational Investigation for Students into the Planetary Impact Process and its Environmental Consequences

NASA Technical Reports Server (NTRS)

Levine, Arlene S.

2008-01-01

Planetary impact craters are a common surface feature of many planetary bodies, including the Earth, the Moon, Mars, Mercury, Venus, and Jupiter s moons, Ganymede and Callisto. The NASA Langley Research Center in Hampton, VA, is located about 5 km inside the outer rim of the Chesapeake Bay Impact Crater. The Chesapeake Bay Impact Crater, with a diameter of 85 km is the sixth largest impact crater on our planet. The U.S. Geological Survey (USGS), in collaboration with the NASA Langley Research Center, the Virginia Department of Environmental Quality (VDEQ), the Hampton Roads Planning District Commission (HRPDC), and the Department of Geology of the College of William and Mary (WM) drilled into and through the crater at the NASA Langley Research Center and obtained a continuous core to a depth of 2075.9 ft (632.73 meters) from the Chesapeake Bay Impact Crater. At the NASA Langley location, the granite basement depth was at 2046 ft (623.87 meters). This collaborative drilling activity provided a unique educational opportunity and ongoing educational partnership between USGS, NASA Langley and the other collaborators. NASA Langley has a decade-long, ongoing educational partnership with the Colonial Coast Council of the Girl Scouts. The core drilling and on site analysis and cataloguing of the core segments provided a unique opportunity for the Girl Scouts to learn how geologists work in the field, their tools for scientific investigation and evaluation, how they perform geological analyses of the cores in an on-site tent and learn about the formation of impact craters and the impact of impacting bodies on the sub-surface, the surface, the oceans and atmosphere of the target body. This was accomplished with a two-part activity. Girl Scout day camps and local Girl Scout troops were invited to Langley Research Center Conference Center, where more than 300 Girl Scouts, their leaders and adult personnel were given briefings by scientists and educators from the USGS, NASA, VDEQ, HRPDC and WM on the principles of geology, the formation of impact craters, the consequences of the impacting body on the atmosphere, ocean, surface and sub-surface, the geological, chemical and biological analyses of the core and the cataloguing and storage of the core segments, etc. After the briefings, the Girl Scouts visited the drilling site where they inspected the core drilling rig, examined the core samples and discussed the drilling procedures, cores and interpretation of the cores with scientists and educators from the organizations conducting the core drilling. Demonstrations at the drilling site included demonstrations of impacting objects hitting multi-colored layered mud targets at different angles of entry. The multi-colored layers of mud were instructive in mapping out the distribution of impact-ejected material around the impact crater. The presentation will include a series of photographs of the Girl Scout participating in activities at the Chesapeake Bay Impact Crater drill site, including retrieving cores from the drilling rig, inspecting the core samples and participating in the impact-crater formation demonstrations.

Optimizing Geothermal Drilling: Oil and Gas Technology Transfer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tilley, Mitch; Eustes, Alfred; Visser, Charles

There is a significant amount of financial risk associated with geothermal drilling; however, there are opportunities to improve upon current practices and technologies used. The scope of this drilling operational study included 21 geothermal wells and 21 oil and gas wells. The goal was to determine a 'perfect well' using historical data to compare the best oil and gas well to the best geothermal well. Unfortunately, limitations encountered in the study included missing data (bit records, mud information, etc.), poor data collection, and difficult to ascertain handwriting. An online software database was used to format drilling data to IADC codedmore » daily drilling reports and generate analysis figures. Six major issues have been found in geothermal drilling operations. These problems include lost circulation, rig/equipment selection, cementing, penetration rate, drilling program, and time management. As a result of these issues, geothermal drilling averages 56.4 days longer than drilling comparable oil and gas wells in the wells in this study. Roughly $13.9 million would be lost due to non-productive time in the 21 geothermal wells and only $1.3 million in the oil and gas wells, assuming a cost of $50,000 per day. Comparable events such as drilling the same sized hole, tripping in/out, cementing, and running the same size casing took substantially less time in the oil and gas wells. Geothermal wells were drilled using older and/or less advanced technology to depths less than 10,000 feet, while oil and gas wells reached 12,500 feet faster with purpose built rigs. A new approach is now underway that will optimize drilling programs throughout the drilling industry. It is the use of Mechanical Specific Energy (MSE) as a tool to realize efficient drilling processes. However, a work-flow must also be established in order for there to be an efficient drilling program. Potential improvements for current geothermal operations are: the use of electronic records, real time services, and official glossary terms to describe rig operations, and advanced drilling rigs/technology.« less

Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

PubMed

Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

2011-02-01

In an alumina refinery, bauxite ore is treated with sodium hydroxide at high temperatures and pressures and for every tone of alumina produced, about 2 tones of alkaline, saline bauxite processing waste is also produced. At Alcoa, a dry stacking system of disposal is used, and it is the sand fraction of the processing waste that is rehabilitated. There is little information available regarding the most appropriate amendments to add to the processing sand to aid in revegetation. The purpose of this study was to investigate how the addition of organic wastes (biosolids and poultry manure), in the presence or absence of added residue mud, would affect the properties of the residue sand and its suitability for revegetation. Samples of freshly deposited residue sand were collected from Alcoa's Kwinana refinery. Samples were treated with phosphogypsum (2% v/v), incubated, and leached. A laboratory experiment was then set up in which the two organic wastes were applied at 0 or the equivalent to 60 tones ha(-1) in combination with residue mud added at rates of 0%, 10% and 20% v/v. Samples were incubated for 8 weeks, after which, key chemical, physical and microbial properties of the residue sand were measured along with seed germination. Additions of residue mud increased exchangeable Na(+), ESP and the pH, and HCO (3) (-) and Na(+) concentrations in saturation paste extracts. Additions of biosolids and poultry manure increased concentrations of extractable P, NH (4) (+) , K, Mg, Cu, Zn, Mn and Fe. Addition of residue mud, in combination with organic wastes, caused a marked decrease in macroporosity and a concomitant increase in mesoporosity, available water holding capacity and the quantity of water held at field capacity. With increasing residue mud additions, the percentage of sample present as sand particles (<1 mm diameter) decreased, and the percentage present in aggregated form (>2 mm diameter) increased; greatest aggregation occurred where a combination of residue mud and poultry manure were added. Stability of aggregates, as measured by wet sieving, was greatest where poultry manure was applied. Although total organic C and soluble organic C were greater in biosolids than poultry manure treatments, the reverse was the case for microbial biomass C and basal respiration. In the biosolids and poultry manure treatments, increasing residue mud additions tended to increase soluble C, microbial biomass C and basal respiration. Germination index of watercress was highest in control samples and reduced by additions of biosolids and poultry manure which was attributed to the high EC and possibly high extractable P and NH (4) (+) . The concurrent addition of residue mud and organic wastes can improve chemical, microbial and particularly physical properties of residue sand. Future research should include neutralisation of the mud (e.g. with gypsum) and subsequent leaching to remove salts originating from both the mud and organic wastes.

40Ar/39Ar dating and zircon chronochemistry for the Izu-Bonin rear arc, IODP site U1437

NASA Astrophysics Data System (ADS)

Schmitt, A. K.; Konrad, K.; Andrews, G. D.; Horie, K.; Brown, S. R.; Koppers, A. A. P.; Busby, C.; Tamura, Y.

2016-12-01

The scientific objective of IODP Expedition 350 drilling at Site U1437 (31°47.390'N, 139°01.580'E) was to reveal the "missing half of the subduction factory": the rear arc of a long-lived intraoceanic subduction zone. Site U1437 lies in a 50 km long and 20 km wide volcano-bounded basin, 90 km west of the Izu arc front, and is the only IODP site drilled in the rear arc. The Izu rear arc is dominated by Miocene basaltic to dacitic seamount chains, which strike at a high angle to the arc front. Radiometric dating targeted a single igneous unit (1390 mbsf), and fine to coarse volcaniclastic units for which we present zircon and 40Ar/39Ar (hornblende, plagioclase, and groundmass) age determinations. All zircons analyzed as grain separates were screened for contamination from drill-mud (Andrews et al., 2016) by analyzing trace elements and, where material was available, O and Hf isotope compositions. Igneous Unit 1 is a rhyolite sheet and yielded concordant in-situ and crystal separate U-Pb zircon ages (13.7±0.3 Ma; MSWD = 1.3; n = 40 spots), whereas the 40Ar/39Ar hornblende plateau age (12.9±0.3; MSWD = 1.1; n = 9 steps) is slightly younger, possibly reflecting pre-eruptive zircon crystallization, or alteration of hornblende. U-Pb zircon and 40Ar/39Ar plateau ages from samples above igneous Unit 1 are concordant with biostratigraphic and paleomagnetic ages (available to 1300 mbsf), but plagioclase and groundmass samples below 1300 m become younger with depth, hinting at post-depositional alteration. A single zircon from 1600 mbsf yielded a U-Pb age of 15.4±1.8 Ma; its trace element composition resembles other igneous zircons from U1437, and is tentatively interpreted as a Middle Miocene age for the lowermost lithostratigraphic unit VII. Oxygen and Hf isotopic values of igneous zircon indicate mantle origins, with some influence of assimilation of hydrothermally altered oceanic crust evident in sub-mantle oxygen isotopic compositions. Lessons from site U1437 are that integrated chronochemistry is essential for achieving accurate age models in oceanic drilling. Reference: Andrews, G. D., Schmitt, A. K., Busby, C. J., Brown, S. R., Blum, P., & Harvey, J. (2016). Age and compositional data of zircon from sepiolite drilling mud to identify contamination of ocean drilling samples. G3. doi: 10.1002/2016GC006397.

Sub Surface Geoelectrical Imaging for Potential Geohazard in Infrastructure Construction in Sidoarjo, East Java

NASA Astrophysics Data System (ADS)

Sumintadireja, Prihadi; Irawan, Diky

2017-06-01

Mud volcano remnants are identified in Surabaya and adjacent areas. The people in East Java based on historical report are custom and able to adjust with the natural phenomena within their areas. Sidoarjo mud volcano phenomena which coincident with drilling activity in 29 May 2006 is making people and government anxious for development a new infrastructure such as high rise building, toll road etc. An understanding of a geological hazard which can be single, sequential or combined events in their origin is the main key importance in subsurface imaging. Geological hazard can be identified by geophysical, geological, geotechnical method. The prompt selection of geophysical method to reveal subsurface condition is very important factor instead of survey design and field data acquisition. Revealing subsurface condition is very important information for site investigation consists of geological, geophysical and geotechnical data, whereas data analysis will help civil engineer design and calculate the construction safety.

Origin and significance of clay-coated fractures in mudrock fragments of the SAFOD borehole (Parkfield, California)

USGS Publications Warehouse

Schleicher, A.M.; van der Pluijm, B.A.; Solum, J.G.; Warr, L.N.

2006-01-01

The clay mineralogy and texture of rock fragments from the SAFOD borehole at 3067 m and 3436 m measured depth (MD) was investigated by electron microscopy (SEM, TEM) and X-ray-diffraction (XRD). The washed and ultrasonically cleaned samples show slickenfiber striations and thin films of Ca-K bearing smectite that are formed on polished fault surfaces, along freshly opened fractures and within adjacent mineralized veins. The cation composition and hydration behavior of these films differ from the Namontmorillonite of the fresh bentonite drilling mud, although there is more similarity with circulated mud recovered from 3479 m MD. We propose that these thin film smectite precipitates formed by natural nucleation and crystal growth during fault creep, probably associated with the shallow circulation of low temperature aqueous fluids along this shallow portion of the San Andreas Fault. Copyright 2006 by the American Geophysical Union.

Measuring Concentrations of Dissolved Methane and Ethane and the 13 C of Methane in Shale and Till.

PubMed

Hendry, M Jim; Barbour, S Lee; Schmeling, Erin E; Mundle, Scott O C

2017-01-01

Baseline characterization of concentrations and isotopic values of dissolved natural gases is needed to identify contamination caused by the leakage of fugitive gases from oil and gas activities. Methods to collect and analyze baseline concentration-depth profiles of dissolved CH 4 and C 2 H 6 and δ 13 C-CH 4 in shales and Quaternary clayey tills were assessed at two sites in the Williston Basin, Canada. Core and cuttings samples were stored in Isojars ® in a low O 2 headspace prior to analysis. Measurements and multiphase diffusion modeling show that the gas concentrations in core samples yield well-defined and reproducible depth profiles after 31-d equilibration. No measurable oxidative loss or production during core sample storage was observed. Concentrations from cuttings and mud gas logging (including IsoTubes ® ) were much lower than from cores, but correlated well. Simulations suggest the lower concentrations from cuttings can be attributed to drilling time, and therefore their use to define gas concentration profiles may have inherent limitations. Calculations based on mud gas logging show the method can provide estimates of core concentrations if operational parameters for the mud gas capture cylinder are quantified. The δ 13 C-CH 4 measured from mud gas, IsoTubes ® , cuttings, and core samples are consistent, exhibiting slight variations that should not alter the implications of the results in identifying the sources of the gases. This study shows core and mud gas techniques and, to a lesser extent, cuttings, can generate high-resolution depth profiles of dissolved hydrocarbon gas concentrations and their isotopes. © 2016, National Ground Water Association.

Sidoarjo mudflow phenomenon and its mitigation efforts

NASA Astrophysics Data System (ADS)

Wibowo, H. T.; Williams, V.

2009-12-01

Hot mud first erupted in Siring village, Porong, Sidoarjo May 29th 2006. The mud first appeared approximately 200 meters from Banjarpanji-1 gas-drilling well. The mud volume increased day by day, from 5000 cubic meters per day on June 2006 to 50,000 cubic meters per day during the last of 2006, and then increased to 100,000-120,000 cubic meters per day during 2007. Flow still continues at a high rate. Moreover, as the water content has gone down, the clast content has gone up. Consequently, there is now the threat of large amounts of solid material being erupted throughout the area. Also, there is the issue of subsurface collapse and ground surface subsidence. The Indonesian government has set up a permanent team to support communities affected by the mudflow that has swamped a number of villages near LUSI. Toll roads, railway tracks and factories also have been submerged and over 35,000 people have been displaced to date. The Sidoarjo Mudflow Mitigation Agency [SMMA, BPLS (Indonesia)] replaces a temporary team called National Team PSLS which was installed for seven months and ended their work on 7 April 2007. BPLS was set up by Presidential Regulation No. 14 / 2007, and it will have to cover the costs related to the social impact of the disaster, especially outside the swamped area. BPLS is the central government institution designated to handle the disaster by coordination with both the drilling company and local (provincial and district) governments. It takes a comprehensive, integrated and holistic approach for its mission and challenges. Those are: 1) How to stop the mudflow, 2) How to mitigate the impacts of the mudflow, and 3) How to minimize the social, economic, environmental impacts, and infrastructure impacts. The mudflow mitigation efforts were constrained by dynamic geology conditions, as well as resistance to certain measures by residents of impacted areas. Giant dykes were built to retain the spreading mud, and the mudflow from the main vent was diverted into the Porong River through a mud pump system. Also we continuously monitor changes in eruption behavior and try to anticipate the consequences, particularly after the Ring Dyke (of main vent) collapsed and became useless in controlling the flow. In September 2009 spectacular eruption intensity with kick and wave developed and is continuing. Surface and subsurface investigations continue ceaselessly to try to understand the forces driving the eruption. There are no precedents for mitigation of such a large scale mud volcano in a densely populated area that seems destined to continue for a very long time. This makes all efforts to stop eruption together with the emergency efforts, which have to be conducted simultaneously with recovery and reconstruction efforts that cover all basic needs of people live in the area. This is why BPLS has to develop innovative and creative efforts, mainly by applying the basic principle of learning by doing.

The Dead Sea Mud and Salt: A Review of Its Characterization, Contaminants, and Beneficial Effects

NASA Astrophysics Data System (ADS)

Bawab, Abeer Al; Bozeya, Ayat; Abu-Mallouh, Saida; Abu Irmaileh, Basha'er; Daqour, Ismail; Abu-Zurayk, Rund A.

2018-02-01

The Dead Sea has been known for its therapeutic and cosmetic properties. The unique climatic conditions in the Dead Sea area make it a renowned site worldwide for the field of climatotherapy, which is a natural approach for the provision of medications for many human diseases including unusual exclusive salt composition of the water, a special natural mud, thermal mineral springs, solar irradiation, oxygen-rich and bromine-rich haze. This review focuses on the physical, chemical, and biological characteristics of the Dead Sea mud and salts, in addition to their contaminants, allowing this review to serve as a guide to interested researchers to their risks and the importance of treatment. Beneficial effects of Dead Sea mud and salts are discussed in terms of therapy and cosmetics. Additional benefits of both Dead Sea mud and salts are also discussed, such as antimicrobial action of the mud in relation to its therapeutic properties, and the potency of mud and salts to be a good medium for the growth of a halophilic unicellular algae, used for the commercial production of β-carotene Dunaliella.

A progress report on results of test drilling and ground-water investigations of the Snake Plain aquifer, southeastern Idaho: Part 1: Mud Lake Region, 1969-70 and Part 2: Observation Wells South of Arco and West of Aberdeen

USGS Publications Warehouse

Crosthwaite, E.G.

1973-01-01

The results of drilling test holes to depths of approximately 1,000 feet in the Mud Lake region show that a large part of the region is underlain by both sedimentary deposits and basalt flows. At some locations, predominantly sedimentary deposits were penetrated; at others, basalt flows predominated. The so-called Mud Lake-Market Lake barrier denotes a change in geology. From the vicinity of the barrier area, as described by Stearns, Crandall, and Steward (1938, p. 111), up the water-table gradient for at least a few tens of miles, the saturated geologic section consists predominantly of beds of sediments that are intercalated with numerous basalt flows. Downgradient from the barrier, sedimentary deposits are not common and practically all the water-bearing formations are basalt, at least to the depths explored so far. Thus, the barrier is a transition zone from a sedimentary-basaltic sequence to a basaltic sequence. The sedimentary-basaltic sequence forms a complex hydrologic system in which water occurs under water-table conditions in the upper few tens of feet of saturated material and under artesian conditions in the deeper material in the southwest part of the region. The well data indicate that southwest of the barrier, artesian pressures are not significant. Southwest of the barrier, few sedimentary deposits occur in the basalt section and, as described by Mundorff, Crosthwaite, and Kilburn (1964). ground water occurs in a manner typical of the Snake Plain aquifer. In several wells, artesian pressures are higher in the deeper formations than in the shallower ones, but the reverse was found in a few wells. The available data are not adequate to describe the water-bearing characteristics of the artesian aquifer nor the effects that pumping in one zone would have on adjacent zones. The water-table aquifer yields large quantities of water to irrigation wells.

Managing Geothermal Exploratory Drilling Risks Drilling Geothermal Exploration and Delineation Wells with Small-Footprint Highly Portable Diamond Core Drills

NASA Astrophysics Data System (ADS)

Tuttle, J.; Listi, R.; Combs, J.; Welch, V.; Reilly, S.

2012-12-01

Small hydraulic core rigs are highly portable (truck or scow-mounted), and have recently been used for geothermal exploration in areas such as Nevada, California, the Caribbean Islands, Central and South America and elsewhere. Drilling with slim diameter core rod below 7,000' is common, with continuous core recovery providing native-state geological information to aid in identifying the resource characteristics and boundaries; this is a highly cost-effective process. Benefits associated with this innovative exploration and delineation technology includes the following: Low initial Capital Equipment Cost and consumables costs Small Footprint, reducing location and road construction, and cleanup costs Supporting drill rod (10'/3meter) and tools are relatively low weight and easily shipped Speed of Mobilization and rig up Reduced requirements for support equipment (cranes, backhoes, personnel, etc) Small mud systems and cementing requirements Continuous, simplified coring capability Depth ratings comparable to that of large rotary rigs (up to ~10,000'+) Remote/small-location accessible (flown into remote areas or shipped in overseas containers) Can be scow or truck-mounted This technical presentation's primary goal is to share the technology of utilizing small, highly portable hydraulic coring rigs to provide exploratory drilling (and in some cases, production drilling) for geothermal projects. Significant cost and operational benefits are possible for the Geothermal Operator, especially for those who are pursuing projects in remote locations or countries, or in areas that are either inaccessible or in which a small footprint is required. John D. Tuttle Sinclair Well Products jtuttle@sinclairwp.com

Construction Foundation Report. Mud Mountain Dam Seepage Control Cutoff Wall, White River, Washington

DTIC Science & Technology

1991-08-01

a suspended man basket. All work, including Government investigations, was done from the man basket and in some instances from a boatswain’s chair...Teale, Somerton , etc.. The Enpasol recordings rely on the same basic principle. The Enpasol is a "black box" monitoring up to 8 drilling parameters...below, Kelly bar is center. Inspector being lowered into access shaft with a man basket. Note liner plates, left. Density test being taken in core

Barite

USGS Publications Warehouse

Miller, M.

2011-01-01

The article discusses the latest developments in the barite or baryte industry, particularly in the U.S., as of June 2011. It claims that the bulk of barites production in the country comes from four mines in Nevada, including the Big Ledge Mine, the Rossi Mine and the Greystone Mine. It cites that barite is mainly used as a weighting agent in natural gas and oil field drilling muds. Barite is also utilized as filler, extender or weighting agent in such products as paints, plastics and rubber.

ADVANCED CUTTINGS TRANSPORT STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stefan Miska; Troy Reed; Ergun Kuru

2004-09-30

The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimizationmore » of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a part of this project, instrumentation was developed to monitor cuttings beds and characterize foams in the flow loop. An ultrasonic-based monitoring system was developed to measure cuttings bed thickness in the flow loop. Data acquisition software controls the system and processes the data. Two foam generating devices were designed and developed to produce foams with specified quality and texture. The devices are equipped with a bubble recognition system and an in-line viscometer to measure bubble size distribution and foam rheology, respectively. The 5-year project is completed. Future research activities will be under the umbrella of Tulsa University Drilling Research Projects. Currently the flow loop is being used for testing cuttings transport capacity of aqueous and polymer-based foams under elevated pressure and temperature conditions. Subsequently, the effect of viscous sweeps on cuttings transport under elevated pressure and temperature conditions will be investigated using the flow loop. Other projects will follow now that the ''steady state'' phase of the project has been achieved.« less

Effects of thermal treatments on the characterisation and utilisation of red mud with sawdust additive.

PubMed

Liu, Yanju; Naidu, Ravi; Ming, Hui; Dharmarajan, Rajarathnam; Du, Jianhua

2016-06-01

Extremely large amounts of red mud (bauxite residue) are generated globally every year from alumina refining industries, which are being disposed of on engineered landfills. The objective of this study is to investigate the effects of thermal treatments on red mud for development of utilisation strategies. Thermal treatments of red mud samples and their characterisations were investigated under inert (N2) and oxidative (air) conditions with and without sawdust addition at 200-600°C. After calcination, the resulting samples were analysed using thermogravimetric-infrared spectroscopy (TG-IR) for functional group transformations, thermogravimetric analysis (TGA) for thermal loss profiles and X-ray diffraction (XRD) for mineral transformations. The characterisation results showed that in N2 environment, boehmite in red mud was transferred to transition alumina at around 400°C while losing water from structural components. The addition of sawdust for incubation and calcination of red mud in air increased the surface area, whereas that in nitrogen atmosphere lead to reduction of hematite to magnetite at around 500°C. The incorporated carbon materials played a major role in increasing the surface area especially for pore size less than 2.5 nm. This treated red mud with altered mineral composition and improved properties for binding contaminants can be used for environmental remediation and in the process of metal recovery such as iron. © The Author(s) 2016.

Feasibility of co-reduction roasting of a saprolitic laterite ore and waste red mud

NASA Astrophysics Data System (ADS)

Wang, Xiao-ping; Sun, Ti-chang; Kou, Jue; Li, Zhao-chun; Tian, Yu

2018-06-01

Large scale utilization is still an urgent problem for waste red mud with a high content of alkaline metal component in the future. Laterite ores especially the saprolitic laterite ore are one refractory nickel resource, the nickel and iron of which can be effectively recovered by direct reduction and magnetic separation. Alkaline metal salts were usually added to enhance reduction of laterite ores. The feasibility of co-reduction roasting of a saprolitic laterite ore and red mud was investigated. Results show that the red mud addition promoted the reduction of the saprolitic laterite ore and the iron ores in the red mud were co-reduced and recovered. By adding 35wt% red mud, the nickel grade and recovery were 4.90wt% and 95.25wt%, and the corresponding iron grade and total recovery were 71.00wt% and 93.77wt%, respectively. The X-ray diffraction (XRD), scanning electron microscopy, and energy dispersive spectroscopy (SEM-EDS) analysis results revealed that red mud addition was helpful to increase the liquid phase and ferronickel grain growth. The chemical compositions "CaO and Na2O" in the red mud replaced FeO to react with SiO2 and MgSiO3 to form augite.

Effect of PDC bit design and confining pressure on bit-balling tendencies while drilling shale using water base mud

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hariharan, P.R.; Azar, J.J.

1996-09-01

A good majority of all oilwell drilling occurs in shale and other clay-bearing rocks. In the light of relatively fewer studies conducted, the problem of bit-balling in PDC bits while drilling shale has been addressed with the primary intention of attempting to quantify the degree of balling, as well as to investigate the influence of bit design and confining pressures. A series of full-scale laboratory drilling tests under simulated down hole conditions were conducted utilizing seven different PDC bits in Catoosa shale. Test results have indicated that the non-dimensional parameter R{sub d} [(bit torque).(weight-on-bit)/(bit diameter)] is a good indicator ofmore » the degree of bit-balling and that it correlated well with Specific-Energy. Furthermore, test results have shown bit-profile and bit-hydraulic design to be key parameters of bit design that dictate the tendency of balling in shales under a given set of operating conditions. A bladed bit was noticed to ball less compared to a ribbed or open-faced bit. Likewise, related to bit profile, test results have indicated that the parabolic profile has a lesser tendency to ball compared to round and flat profiles. The tendency of PDC bits to ball was noticed to increase with increasing confining pressures for the set of drilling conditions used.« less

Adding worms during composting of organic waste with red mud and fly ash reduces CO2 emissions and increases plant available nutrient contents.

PubMed

Barthod, J; Rumpel, C; Calabi-Floody, M; Mora, M-L; Bolan, N S; Dignac, M-F

2018-09-15

Alkaline industrial wastes such as red mud and fly ash are produced in large quantities. They may be recycled as bulking agent during composting and vermicomposting, converting organic waste into soil amendments or plant growth media. The aim of this study was to assess the microbial parameters, greenhouse gas emissions and nutrient availability during composting and vermicomposting of household waste with red mud and fly ash 15% (dry weight). CO 2 , CH 4 and N 2 O emissions were monitored during 6 months in controlled laboratory conditions and microbial biomass and phospholipid acids, N and P availability were analysed in the end-products. Higher CO 2 emissions were observed during vermicomposting compared to composting. These emissions were decreased by red mud addition, while fly ash had no effect. Nitrate (NO 3 -N) content of the end-products were more affected by worms than by alkaline materials, while higher ammonium (NH 4 -N) contents were recorded for composts than vermicomposts. Red mud vermicompost showed higher soluble P proportion than red mud compost, suggesting that worm presence can counterbalance P adsorption to the inorganic matrix. Final composts produced with red mud showed no harmful heavy metal concentrations. Adding worms during composting thus improved the product nutrient availability and did not increase metal toxicity. From a practical point of view, this study suggests that for carbon stabilisation and end-product quality, the addition of red mud during composting should be accompanied by worm addition to counterbalance negative effects on nutrient availability. Copyright © 2018. Published by Elsevier Ltd.

The Ba/Ca record of corals from the Southern Gulf of Mexico: contributions from land-use changes, fluvial discharge and oil-drilling muds.

PubMed

Carriquiry, José D; Horta-Puga, Guillermo

2010-09-01

The Ba/Ca in the growth bands of Montastraea faveolata from the Veracruz Reef System was used to reconstruct the long-term environmental change associated to anthropogenic activity in the Southern Gulf of Mexico (SGM). The 168-yr coral record shows two periods of distinct Ba concentrations: a pre-industrial period (1835-1965: 7.54 micromol/mol) followed by an industrial one (1966-2000: 8.57 micromol/mol). As human population quadrupoled during the latter, sediment load in the fluvial discharge also increased due to changes in land-use, yielding a 14% increase in the Ba-levels. A remarkable finding is that the periods at which the coral Ba/Ca ratio losses its correlation with fluvial discharge coincide exactly with peak periods of high barite consumption (used for oil drilling) in the Northern Gulf of Mexico, and the onset of oil drilling in the SGM. This finding suggests that barite may be one of the dominant sources for dissolved-Ba in the SGM. Copyright 2010 Elsevier Ltd. All rights reserved.

Four Years of Chemical Measurements from the Deepwater Horizon Oil Spill Define the Deep Sea Sediment footprint and Subsequent Recovery

NASA Astrophysics Data System (ADS)

Boehm, P.

2016-02-01

Chemical data acquired during and after the DWHOS showed that several mechanisms were responsible for transport of oil from the water column to the sediments in the deep sea off the continental shelf. Three primary pathways were identified:Sorption onto and sinking of drilling mud particles during "Top Kill" response activity, highly scattered deposition of residuesfrom in situ burns, and deposition of oil combined with microbial organic matter from diffuse oil plumes ("marine snow"). Data collected during 2010, 2011 and 2014 were used to define the oil footprint and estimate time to recovery. More than 1200 stations were sampled. Of these, 27 stations were visited all three years, providing a time series from which recovery rates were calculated using the loss of total polycyclic aromatic hydrocarbons (TPAH) over time fit to first order kinetics. Results showed that the footprint of the oil was limited to the area around the wellhead and in patches to the southwest. Mostsamples had returned to background levels by 2015, with some exceptions close to the wellhead. Deposition to the northeast (DeSoto Canyon) was minor as evidenced by the absence of oil in sediments in that area. Samples with the longest recovery times were within 2 nautical miles of the wellhead, and often contained drilling mud, as shown by olefin signatures on the GC/FID chromatogram. Detailed chemistry data evaluation and chemical fingerprinting provided evidence that oil was being degraded in situ.

Application of Formation Testing While Drilling (GeoTap) for acquiring formation pressure data from the Azeri, Chirag and Guneshli wells which were drilled in the Khazarian-Caspian Sea of the Azerbaijan Republic

NASA Astrophysics Data System (ADS)

Amirov, Elnur

2016-04-01

A new technology to acquire wireline quality pressure tests using a Logging While Drilling approach has been successfully implemented few years ago in Azeri, Chirag and Guneshli wells which were drilled in the Khazarian-Caspian Sea of the Azerbaijan Republic. The Formation Tester While Drilling tool (GeoTap) uses a testing sequence similar to wireline tools. A single probe is extended to the borehole wall and a small pretest volume withdrawn from the formation. The resulting pressure transient is then analyzed for formation pressure, formation permeability and mobility information. Up-link and down-link capabilities have been added to achieve test control and quality feedback. An efficient downlink algorithm is used downhole to analyze the data. The parameters and pressure data are transmitted to the surface in real-time for continuous monitoring of the test. More detailed pressure data is recorded and retrieved after returning to surface. Use of a quartz gauge allows excellent accuracy. Azeri, Chirag and Guneshli fields consist of layered sand reservoirs alternation with shale sequences and detailed pressure data is acquired on a high percentage of wells in order to understand lateral and vertical continuity of different flow units. The formation tester can be utilized with the 'triple combo' Logging While Drilling string which eliminates the need to rig up wireline on many wells. Wireline formation tester runs are time consuming - particularly if high deviation or high overbalance conditions are encountered requiring pipe conveyed techniques. Non-Productive Time is high when the wireline tools are stuck and fishing operations are required. The Sperry Drilling GeoTap formation pressure tester service provides real-time formation pressure measurements. It bridges the critical gap between drilling safety and optimization, by providing early and reliable measurements of key reservoir properties, while improving reservoir understanding and completion design in real time. The GeoTap tester obtains direct pore-pressure measurements as the well is being drilled, with accuracy and precision comparable to that of wireline testers. The GeoTap service can eliminate the time, risk, and cost associated with running pipe-conveyed wireline test tools. It also measures annular and bore pressure while drilling, providing accurate, continuous, real-time hydrostatic pressure, and equivalent circulating density (ECD) information. This aids in determining and maintaining optimal mud weight, reduces formation damage, increases the rate of penetration, and increases operational safety. GeoTap benefits can be improvement of formation evaluation, real-time fluid gradients and fluid mobility (permeability/viscosity indicator), identification of fluid contact points, determination of reservoir connectivity/compartmentalization and depletion, increase safety of operation, determination of optimal mud weight and manage of ECD. We can also continuously monitor wellbore stability for assessments in order to reduce formation damage which in turns will help to increase drilling effectiveness (determine precise overbalance for maximizing ROP and continuously monitor hole-cleaning effectiveness with pressure-while-drilling, while reducing formation damage due to swab/surge). Save time and money by reducing rig down time associated with wireline testing. GeoTap Tool capable of performing more than 150 pressure tests per run and optional orientation of pressure measurement is available (top, right, bottom or left). GeoTap testing has been completed with encouraging results in many wells up to circa 3000m deep. Data has been acquired successfully both in a "Drill-Test-Drill' mode and a "Post-Drill-Test" mode. GeoTap tests have spanned wide ranges of borehole temperature, pressure, mobility as well as formation permeability and overbalance conditions. GeoTap tests in Azeri, Chirag and Guneshli wells which were drilled in the Khazarian-Caspian Sea of the Azerbaijan Republic have proved that a logging while drilling approach can be successfully employed to acquire formation pressure data in open hole (which is also very useful for fluid gradient analysis, oil water and gas oil contacts delineation/identification).

Soil-Water Repellency and Critical Humidity as Cleanup Criteria for Remediation of a Hydrocarbon Contaminated Mud

NASA Astrophysics Data System (ADS)

Guzmán, Francisco Javier; Adams, Randy H.

2010-05-01

The majority of soil remediation programs focus mainly on reducing the hydrocarbon concentration, based on the assumption that the primary impact is toxicity and/or leachates and that these are directly proportional to concentration. None-the-less, interference with natural soil-water interactions are frequently more damaging, especially for sites contaminated with very viscous, weathered hydrocarbons. Therefore, the kind of hydrocarbons present in the soil and their interactions with soil surfaces may be more important than the overall hydrocarbon concentration in terms of soil restoration. One recently patented technology, the Chemical-Biological Stabilization process, focuses specifically on restoring soil fertility as the main objective for remediation of sites with agricultural use. This method was recently validated at an industrial scale by the treatment of 150 cubic meters of bentonitic drilling muds (70,5% fines) from an old sulphur mine, which were contaminated with very weathered oil (4° API), consisting of 31% asphaltenes. This material was treated by adding 4% (w/w, dry) of calcium hydroxide, followed by 4% (w/w, dry) of sugar cane cachasse (a fine fibered agricultural waste), thoroughly mixing between additions using an excavator. After the soil had dried sufficiently and the pH was <8, a fine-rooted, C-4 tropical grass (Brachiaria humidicola) was planted by seed. Over a two year period this material was monitored for several factors including field moisture (%H), field capacity (FC), and soil water repellency. MED was measured on air dried soil and WDPT values were calculated from the extrapolation of penetration time vs. ethanol molarity functions (Rx=0,99). Additionally, water penetration times were measured at different humidities to determine critical moisture levels for absorption in <5s and <60s. Initially, the FC increased from 24,9%H to 33,8%H (in 4½ months), probably due to the addition of the organic amendment. Over the next 6½ months, the FC dropped to 25,6% H, likely due to organic matter decomposition. However, during the following year+ (13½ months) the FC increased to 33,8%H probably due to an increase of soil humic substances while a vigorous vegetative growth was established. During two years of treatment the MED values were reduced 30% from 5,13 to 3,58M, and WDPT values were reduced over 25 times (from 10 exp5,6 s to 10 exp4,2 s). Critical humidity values varied from ~16,9 - 19,5%H for penetration in <5 s and from ~15,1 - 15,5%H for penetration in <60 s, in both treated and untreated material. During the driest part of the year, in May before the first rains, the soil humidity was 20,3%, and thus values below the critical levels were not experienced. This permitted the development of a complete vegetative cover, vigorous growth, and transformation of a geologic substrate (bentonitic drilling muds) into a soil-like material apt for agricultural use. This focus on soil-water relationships and the use of soil fertility parameters in general is important in establishing cleanup criteria for the real remediation of hydrocarbon contaminated sites in agricultural areas. As seen in this study, relatively high WDPT and MED values may not necessarily indicate soil moisture problems and these need to be complemented with actual site information on soil humidity during the annual cycle and with determinations of critical humidity. Additionally, the augmentation of field capacity using organic conditioners may effectively mitigate potential critical humidity problems.

Geologic framework of the 2005 Keathley Canyon gas hydrate research well, northern Gulf of Mexico

USGS Publications Warehouse

Hutchinson, D.R.; Hart, P.E.; Collett, T.S.; Edwards, K.M.; Twichell, D.C.; Snyder, F.

2008-01-01

The Keathley Canyon sites drilled in 2005 by the Chevron Joint Industry Project are located along the southeastern edge of an intraslope minibasin (Casey basin) in the northern Gulf of Mexico at 1335 m water depth. Around the drill sites, a grid of 2D high-resolution multichannel seismic data designed to image depths down to at least 1000 m sub-bottom reveals 7 unconformities and disconformities that, with the seafloor, bound 7 identifiable seismic stratigraphic units. A major disconformity in the middle of the units stands out for its angular baselapping geometry. From these data, three episodes of sedimentary deposition and deformation are inferred. The oldest episode consists of fine-grained muds deposited during a period of relative stability in the basin (units e, f, and g). Both the BSR and inferred gas hydrate occur within these older units. The gas hydrate occurs in near-vertical fractures. A second episode (units c and d) involved large vertical displacements associated with infilling and ponding of sediment. This second interval corresponds to deposition of intercalated fine and coarse-grained material that was recovered in the drill hole that penetrated the thin edges of the regionally much thicker units. The final episode of deposition (units a and b) occurred during more subdued vertical motions. Hemipelagic drape (unit a) characterizes the modern seafloor. The present-day Casey basin is mostly filled. Its sill is part of a subsiding graben structure that is only 10-20 m shallower than the deepest point in the basin, indicating that gravity-driven transport would mostly bypass the basin. Contemporary faulting along the basin margins has selectively reactivated an older group of faults. The intercalated sand and mud deposits of units c and d are tentatively correlated with Late Pleistocene deposition derived from the western shelf-edge delta/depocenter of the Mississippi River, which was probably most active from 320 ka to 70 ka [Winker, C.D., Booth, J., 2000. Sedimentary dynamics of the salt-dominated continental slope, Gulf of Mexico: integration of observations from the seafloor, near-surface, and deep subsurface. In: Proceedings of the GCSSEPM Foundation 20th Annual Research Conference, Deep-water Reservoirs of the World, pp. 1059-1086]. The presence of sand within the gas hydrate stability zone (in units c and d) is not sufficient to concentrate gas hydrate even though dispersed gas hydrate occurs deeper in the fractured mud/clay-rich sections of units e and f.

Global Sea-level Changes Revealed in the Sediments of the Canterbury Basin, New Zealand: IODP Expedition 317

NASA Astrophysics Data System (ADS)

McHugh, C. M.; Fulthorpe, C.; Blum, P.; Rios, J.; Chow, Y.; Mishkin, K.

2012-12-01

Continental margins are composed of thick sedimentary sections that preserve the record of local processes modulated by global sea-level (eustatic) changes and climate. Understanding this regional variability permits us to extract the eustatic record. Integrated Ocean Drilling Program Expedition 317 drilled four sites in the offshore Canterbury Basin, eastern South Island of New Zealand, in water depths of 85 m to 320 m. One of the objectives of the expedition was to understand the influence of eustasy on continental margins sedimentation and to test the concepts of sequence stratigraphy. A high-resolution multiproxy approach that involves geochemical elemental analyses, lithostratigraphy and biostratigraphy is applied to understand the margin's sedimentation for the past ~5 million years. Multichannel seismic data (EW00-01 survey) provide a seismic sequence stratigraphic framework against which to interpret the multiproxy data. The mid- to late Pleistocene sedimentation is characterized by variable lithologies and changing facies. However, elemental compositions and facies follow predictable patterns within seismic sequences. Oxygen isotope measurements for the latest Pleistocene indicate that 100 ky Milankovich astronomical forcing controlled this variability. In contrast, Pliocene and early Pleistocene sediments are composed of repetitive siliciclastic and carbonate mud lithologies with less facies variability. Results of our analyses suggest that repetitive alternations of green and gray mud were deposited during warmer and cooler periods, respectively. Oxygen isotopes suggest that this cyclicity may reflect 40 ky Milankovich forcing. Ocean Drilling Program Legs 150 and 174A drilled on the New Jersey continental margin with similar objectives to those of Expedition 317. Results from this northern and southern hemisphere drilling reveal that eustasy, controlled by Milankovich forcing, strongly influences margin sedimentation and the formation of basin-wide unconformities. However, the correlation between eustasy and seismic sequence formation is not always one to one. High sedimentation rates in the Pleistocene offshore Canterbury Basin record a one- to-one correlation between glacioeustasy and seismic sequences, and in some sequences possibly a higher order frequency. But this is not the case for offshore New Jersey, where accumulation rates were lower and only the uppermost seismic sequences represent 100 ky cycles. Furthermore, Pliocene sedimentation in the Canterbury Basin was also controlled by eustasy, but does not show a one-to-one correlation between Milankovich cycles and seismic stratigraphy. Northern and southern hemisphere comparisons provide a powerful tool to better understand controls on regional sedimentation and extract a global signal.

Impact of oil-based drill mud disposal on benthic foraminiferal assemblages on the continental margin off Angola

NASA Astrophysics Data System (ADS)

Jorissen, F. J.; Bicchi, E.; Duchemin, G.; Durrieu, J.; Galgani, F.; Cazes, L.; Gaultier, M.; Camps, R.

2009-12-01

In order to assess the possible environmental impact of oily cuttings discharged during oil exploration activities, we studied the benthic foraminiferal faunas in a five-station, 4-km-long sampling transect around a cuttings disposal site at about 670 m depth offshore Angola (W Africa), where drilling activities started 1.5 years before sampling. Living (Rose Bengal stained) and dead foraminiferal faunas were sampled in March 2006. The faunal patterns mirror the spatial distribution of hydrocarbons, which are dispersed into a southeastern direction. Four different areas can be distinguished on the basis of the investigated faunal parameters (density, diversity and species composition of the living fauna, and comparison with subrecent dead faunas). The fauna at station S31, 300 m SE of the oil cuttings disposal site, appears to be clearly impacted: the faunal density and diversity are maximal, but evenness is minimal. Taxa sensitive to organic enrichment, such as Uvigerina peregrina, Cancris auriculus and Cribrostomoides subglobosus, have largely disappeared, whereas the low-oxygen-resistant taxon Chilostomella oolina and opportunistic buliminids and bolivinids attain relatively high densities. At station S32, 500 m SE of the disposal site, environmental impact is still perceptible. The faunal density is slightly increased, and U. peregrina, apparently the most sensitive species, is still almost absent. The faunas found at 1 and 1.8 km SE of the disposal site are apparently no longer impacted by the drill mud disposal. Faunal density and diversity are low, and the faunal composition is typical for a mesotrophic to eutrophic upper slope environment. Finally, Station S35, 2 km NW of the disposal site, contains an intermediate fauna, where both the low-oxygen-resistant C. oolina and the more sensitive taxa ( U. peregrina, C. auriculus and C. subglobosus) are present. All taxa live close to the sediment-water interface here, indicating a reduced oxygen penetration into the sediment. Since the hydrocarbon concentration is low at this station, it appears that the faunal characteristics are the consequence of a slightly different environmental setting, and not due to a contamination with drill cuttings. Our data underline the large potential of benthic foraminifera as bio-indicators of anthropogenic enrichment in open marine settings, such as caused by the disposal of oily drill cuttings. The foraminiferal faunas react essentially by a density increase of a number of tolerant and/or opportunistic taxa, and a progressive disappearance of more sensitive taxa in the most impacted area. Rather surprisingly, large-sized taxa appear to be more sensitive than small-sized foraminiferal taxa.

Documenting channel features associated with gas hydrates in the Krishna-Godavari Basin, offshore India

USGS Publications Warehouse

Riedel, M.; Collett, T.S.; Shankar, Ude

2011-01-01

During the India National Gas Hydrate Program (NGHP) Expedition 01 in 2006 significant sand and gas hydrate were recovered at Site NGHP-01-15 within the Krishna-Godavari Basin, East Coast off India. At the drill site NGHP-01-15, a 5-8m thick interval was found that is characterized by higher sand content than anywhere else at the site and within the KG Basin. Gas hydrate concentrations were determined to be 20-40% of the pore volume using wire-line electrical resistivity data as well as core-derived pore-fluid freshening trends. The gas hydrate-bearing interval was linked to a prominent seismic reflection observed in the 3D seismic data. This reflection event, mapped for about 1km2 south of the drill site, is bound by a fault at its northern limit that may act as migration conduit for free gas to enter the gas hydrate stability zone (GHSZ) and subsequently charge the sand-rich layer. On 3D and additional regional 2D seismic data a prominent channel system was imaged mainly by using the seismic instantaneous amplitude attribute. The channel can be clearly identified by changes in the seismic character of the channel fill (sand-rich) and pronounced levees (less sand content than in the fill, but higher than in surrounding mud-dominated sediments). The entire channel sequence (channel fill and levees) has been subsequently covered and back-filled with a more mud-prone sediment sequence. Where the levees intersect the base of the GHSZ, their reflection strengths are significantly increased to 5- to 6-times the surrounding reflection amplitudes. Using the 3D seismic data these high-amplitude reflection edges where linked to the gas hydrate-bearing layer at Site NGHP-01-15. Further south along the channel the same reflection elements representing the levees do not show similarly large reflection amplitudes. However, the channel system is still characterized by several high-amplitude reflection events (a few hundred meters wide and up to ~1km in extent) interpreted as gas hydrate-bearing sand intervals along the length of the channel. ?? 2010.

Monitoring-well installation, slug testing, and groundwater quality for selected sites in South Park, Park County, Colorado, 2013

USGS Publications Warehouse

Arnold, Larry R. Rick

2015-01-01

During May–June, 2013, the U.S. Geological Survey, in cooperation with Park County, Colorado, drilled and installed four groundwater monitoring wells in areas identified as needing new wells to provide adequate spatial coverage for monitoring water quality in the South Park basin. Lithologic logs and well-construction reports were prepared for each well, and wells were developed after drilling to remove mud and foreign material to provide for good hydraulic connection between the well and aquifer. Slug tests were performed to estimate hydraulic-conductivity values for aquifer materials in the screened interval of each well, and groundwater samples were collected from each well for analysis of major inorganic constituents, trace metals, nutrients, dissolved organic carbon, volatile organic compounds, ethane, methane, and radon. Documentation of lithologic logs, well construction, well development, slug testing, and groundwater sampling are presented in this report.

Development of seals for a geothermal downhole intensifier. Progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Captain, K.M.; Harvey, A.C.; Caskey, B.C.

1985-08-01

A system using high-velocity fluid jets in conjunction with a rotary diamond bit is currently considered as the best candidate for reducing the cost of drilling geothermal wells. Technical, safety and cost considerations indicate that the required jet supply pressure can best be established by a downhole pressure intensifier. Key intensifier components are the check valve and plunger seals, which must prevent leakage of the high-pressure, high-temperature abrasive fluid (drilling mud). To achieve the required performance, novel ceramic seals are currently being developed. The check valve seal includes a tapered polymeric plug and ceramic stop acting against a ceramic seat.more » The ceramic plunger seal is a variant of the ''stepped-joint'' piston ring and is designed to minimize contact pressure and abrasive wear. Initial testing of these seals in the laboratory shows encouraging results; design refinement and further testing is in progress. 2 refs., 6 figs., 3 tabs.« less

Study of technology of pile foundation construction of no.5 main pier of Shoujiang bridge in Wenchuan County

NASA Astrophysics Data System (ADS)

Huang, Xianbin; Liu, Chenyang; Chen, Chunyang; Wangren, Yahong; Xu, Jialin; Xian, Jin

2018-03-01

The group of pile foundation of no.5 pier in Shoujiang Bridge needs to overcome the big load of large span continuous steel structure. The length of single pile foundation is 77m and the diameter of single pile foundation is 250cm. It not only faces the flood in the upstream of Shoujiang river, the construction obstacles during summer rain period, but also the reservoir clearance activity of Zipingpu reservoir and the high water level in winter and other water level fluctuation that have huge impact on platform of pile foundation construction. This article introduces the preparation in aspect of personnel, material, equipment and so on of pile foundation construction, and also conduct intensive research on leveling the field, assaying pile location, the embedment of the steel casing, installing the drill, mixing mud, drilling, final hole inspection and clearance, steel cage construction, perfusing concrete under water.

Comprehensive database of wellbore temperatures and drilling mud weight pressures by depth for Judge Digby field, Louisiana

USGS Publications Warehouse

Burke, Lauri

2010-01-01

This document serves as the repository for the unprocessed data used in the investigation of temperature and overpressure relations within the deep Tuscaloosa Formation in Judge Digby field. It is a compilation of all the publicly accessible wellbore temperature and pressure data for Judge Digby field, a prolific natural gas field producing from the Upper Cretaceous lower part of the Tuscaloosa Formation in the Gulf Coast region. This natural gas field is in Pointe Coupee Parish in the southern part of onshore Louisiana.

Development of Overpressures at Nankai Accretionary Prism, Ocean Drilling Program Sites 1173 and 1174

NASA Astrophysics Data System (ADS)

Gamage, K.; Screaton, E.

2003-12-01

In this study, we used a one-dimensional model of sedimentation, initial prism loading, and fluid flow to examine the development of overpressures at the toe of the Nankai accretionary complex. A permeability-porosity relationship was established for hemipelagic sediments from laboratory measured permeabilities as an input to the model. Vertical permeabilities were measured for 10 core samples from the Ocean Drilling Program (ODP) Leg 190, Sites 1173 and 1174, from the upper and lower Shikoku Basin facies. Both sites were drilled along the Muroto Transect through the dècollement zone or its equivalent. Site 1173 is located 11 km seaward of the deformation front and it represents the undeformed incoming sediments, where as Site 1174 represents sediments within the proto-thrust zone. Although turbidite-rich sediments dominate the Nankai accretionary prism, the dècollement and underthrust sediments are primarily composed of hemipelagic muds. Using the permeability-porosity relationship, our modeling results indicate excess pore pressures that are greater than 30% of lithostatic pressure at the toe of the prism at a convergence rate of 4cm/yr. These values are slightly lower than previously inferred excess pore pressures estimated from porosity data. Additional runs were conducted to simulate a 10-m thick low permeability barrier at the dècollement where vertical fluid flow is restricted. The low permeability barrier required a permeability less than 1 x 10-19 m2 to generate excess pore pressures greater than 50% of lithostatic pressure. Modeling was further extended to test the significance of variable prism loading rates due to uncertainties in the convergence rate and affects of lateral stress above the dècollement.

Application program of CRUST-1 10km continental scientific drilling rig in SK-2 scientific drilling well

NASA Astrophysics Data System (ADS)

Sun, Youhong; Gao, Ke; Yu, Ping; Liu, Baochang; Guo, Wei; Ma, Yinlong; Yang, Yang

2014-05-01

SK-2 Well is located in DaQing city,where is site of the largest oil field in China,Heilongjiang province, north-east of China.The objective of SK-2 well is to obtain full cores of cretaceous formation in Song Liao basin,and to build the time tunnel of Cretaceous greenhouse climate change,and to clarify the causes,processes and results of the formations of DaQing oil field. This will ensure to achieve our ultimate goals,to test the CRUST-1 drilling rig and improve China's deep scientific drilling technology,to form the scientific drilling technology,method and system with independent intellectual property rights,and to provide technical knowledge and information for China's ten kilometers super-deep scientific drilling technical resources.SK-2 Well is at 6400 meter depth, where the drilling inclination is 90 degree and the continuous coring length is 3535 meter that from 2865 to 6400 meter,the recovery rate of the core is greater or equal to 95 percent with 100 millimeters core diameter and 3.9 degree per 100 meter geothermal gradient.The CRUST-1 rig is designated with special drilling equipment for continental scientific drilling combined to the oil drilling equipment ability with advanced geological drilling technology which is highly automatic and intelligent. CRUST-1 drilling ability is 10000 meter with the maximum hook load 700 tons, the total power is 4610 Kilowatt.CRUST-1 will be integrated with a complete set of automation equipment,including big torque hydraulic top drive,high accuracy automatic drilling rod feeding system, suspended automatic drill string discharge device,hydraulic intelligent iron roughneck,and hydraulic automatic catwalk to fully meet the drilling process requirements of SK-2.Designed with advanced drilling technique for 260 degree in the bottom of SK-2 well and hard rock,including the drilling tools of high temperature hydraulic hammer,high temperature resistance and high strength aluminum drill pipe,high temperature preparation of mud treatment and high temperature resistant cementing materials, and bionic bits,that is coupling bionic PDC tooth bit and diamond-impregnated bit for hard rock.All parts of CRUST-1 were successfully assembled along with the derrick and base lift and transported about 3456 kilometers from manufacture,GuangHan city in southwest China's Sichuan province,to the well site of SK-2 in end of 2013.SK-2 will be finished during next 4 years.

Leaching of copper and nickel in soil-water systems contaminated by bauxite residue (red mud) from Ajka, Hungary: the importance of soil organic matter.

PubMed

Lockwood, Cindy L; Stewart, Douglas I; Mortimer, Robert J G; Mayes, William M; Jarvis, Adam P; Gruiz, Katalin; Burke, Ian T

2015-07-01

Red mud is a highly alkaline (pH >12) waste product from bauxite ore processing. The red mud spill at Ajka, Hungary, in 2010 released 1 million m(3) of caustic red mud into the surrounding area with devastating results. Aerobic and anaerobic batch experiments and solid phase extraction techniques were used to assess the impact of red mud addition on the mobility of Cu and Ni in soils from near the Ajka spill site. Red mud addition increases aqueous dissolved organic carbon (DOC) concentrations due to soil alkalisation, and this led to increased mobility of Cu and Ni complexed to organic matter. With Ajka soils, more Cu was mobilised by contact with red mud than Ni, despite a higher overall Ni concentration in the solid phase. This is most probably because Cu has a higher affinity to form complexes with organic matter than Ni. In aerobic experiments, contact with the atmosphere reduced soil pH via carbonation reactions, and this reduced organic matter dissolution and thereby lowered Cu/Ni mobility. These data show that the mixing of red mud into organic rich soils is an area of concern, as there is a potential to mobilise Cu and Ni as organically bound complexes, via soil alkalisation. This could be especially problematic in locations where anaerobic conditions can prevail, such as wetland areas contaminated by the spill.

Role of Geomechanics in Assessing the Feasibility of CO2 Sequestration in Depleted Hydrocarbon Sandstone Reservoirs

NASA Astrophysics Data System (ADS)

Fang, Zhi; Khaksar, Abbas

2013-05-01

Carbon dioxide (CO2) sequestration in depleted sandstone hydrocarbon reservoirs could be complicated by a number of geomechanical problems associated with well drilling, completions, and CO2 injection. The initial production of hydrocarbons (gas or oil) and the resulting pressure depletion as well as associated reduction in horizontal stresses (e.g., fracture gradient) narrow the operational drilling mud weight window, which could exacerbate wellbore instabilities while infill drilling. Well completions (casing, liners, etc.) may experience solids flowback to the injector wells when injection is interrupted due to CO2 supply or during required system maintenance. CO2 injection alters the pressure and temperature in the near wellbore region, which could cause fault reactivation or thermal fracturing. In addition, the injection pressure may exceed the maximum sustainable storage pressure, and cause fracturing and fault reactivation within the reservoirs or bounding formations. A systematic approach has been developed for geomechanical assessments for CO2 storage in depleted reservoirs. The approach requires a robust field geomechanical model with its components derived from drilling and production data as well as from wireline logs of historical wells. This approach is described in detail in this paper together with a recent study on a depleted gas field in the North Sea considered for CO2 sequestration. The particular case study shows that there is a limitation on maximum allowable well inclinations, 45° if aligning with the maximum horizontal stress direction and 65° if aligning with the minimum horizontal stress direction, beyond which wellbore failure would become critical while drilling. Evaluation of sanding risks indicates no sand control installations would be needed for injector wells. Fracturing and faulting assessments confirm that the fracturing pressure of caprock is significantly higher than the planned CO2 injection and storage pressures for an ideal case, in which the total field horizontal stresses increase with the reservoir re-pressurization in a manner opposite to their reduction with the reservoir depletion. However, as the most pessimistic case of assuming the total horizontal stresses staying the same over the CO2 injection, faulting could be reactivated on a fault with the least favorable geometry once the reservoir pressure reaches approximately 7.7 MPa. In addition, the initial CO2 injection could lead to a high risk that a fault with a cohesion of less than 5.1 MPa could be activated due to the significant effect of reduced temperature on the field stresses around the injection site.

Effect of red mud addition on tetracycline and copper resistance genes and microbial community during the full scale swine manure composting.

PubMed

Wang, Rui; Zhang, Junya; Sui, Qianwen; Wan, Hefeng; Tong, Juan; Chen, Meixue; Wei, Yuansong; Wei, Dongbin

2016-09-01

Swine manure has been considered as the reservoir of antibiotic resistance genes (ARGs). Composting is one of the most suitable technologies for treating livestock manures, and red mud was proved to have a positive effect on nitrogen conservation during composting. This study investigated the abundance of eight tetracycline and three copper resistance genes, the bacterial community during the full scale swine manure composting with or without addition of red mud. The results showed that ARGs in swine manure could be effectively removed through composting (reduced by 2.4log copies/g TS), especially during the thermophilic phase (reduced by 1.5log copies/g TS), which the main contributor might be temperature. Additionally, evolution of bacterial community could also have a great influence on ARGs. Although addition of red mud could enhance nitrogen conservation, it obviously hindered removal of ARGs (reduced by 1.7log copies/g TS) and affected shaping of bacterial community during composting. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Green's function approach for assessing the thermal disturbance caused by drilling deep boreholes in rock or ice

USGS Publications Warehouse

Clow, Gary D.

2015-01-01

A knowledge of subsurface temperatures in sedimentary basins, fault zones, volcanic environments and polar ice sheets is of interest for a wide variety of geophysical applications. However, the process of drilling deep boreholes in these environments to provide access for temperature and other measurements invariably disturbs the temperature field around a newly created borehole. Although this disturbance dissipates over time, most temperature measurements are made while the temperature field is still disturbed. Thus, the measurements must be ‘corrected’ for the drilling-disturbance effect if the undisturbed temperature field is to be determined. This paper provides compact analytical solutions for the thermal drilling disturbance based on 1-D (radial) and 2-D (radial and depth) Green's functions (GFs) in cylindrical coordinates. Solutions are developed for three types of boundary conditions (BCs) at the borehole wall: (1) prescribed temperature, (2) prescribed heat flux and (3) a prescribed convective condition. The BC at the borehole wall is allowed to vary both with depth and time. Inclusion of the depth dimension in the 2-D solution allows vertical heat-transfer effects to be quantified in situations where they are potentially important, that is, near the earth's surface, at the bottom of a well and when considering finite-drilling rates. The 2-D solution also includes a radial- and time-dependent BC at the earth's surface to assess the impact of drilling-related infrastructure (drilling pads, mud pits, permanent shelters) on the subsurface temperature field. Latent-heat effects due to the melting and subsequent refreezing of interstitial ice while drilling a borehole through ice-rich permafrost can be included in the GF solution as a moving-plane heat source (or sink) located at the solid–liquid interface. Synthetic examples are provided illustrating the 1-D and 2-D GF solutions. The flexibility of the approach allows the investigation of thermal drilling effects in rock or ice for a wide variety of drilling technologies. Numerical values for the required radial GFs GR are available through the Advanced Cooperative Arctic Data and Information Service at doi:10.5065/D64F1NS6.

Sea Bed Drilling Technology MARUM-MeBo: Overview on recent scientific drilling campaigns and technical developments

NASA Astrophysics Data System (ADS)

Freudenthal, Tim; Bergenthal, Markus; Bohrmann, Gerhard; Pape, Thomas; Kopf, Achim; Huhn-Frehers, Katrin; Gohl, Karsten; Wefer, Gerold

2017-04-01

The MARUM-MeBo (abbreviation for Meeresboden-Bohrgerät, the German expression for seafloor drill rig) is a robotic drilling system that is developed since 2004 at the MARUM Center for Marine Environmental Sciences at the University of Bremen in close cooperation with Bauer Maschinen GmbH and other industry partners. The MARUM-MeBo drill rigs can be deployed from multipurpose research vessel like, RV MARIA S. MERIAN, RV METEOR, RV SONNE and RV POLARSTERN and are used for getting long cores both in soft sediments as well as hard rocks in the deep sea. The first generation drill rig, the MARUM-MeBo70 is dedicated for a drilling depth of more than 70 m (Freudenthal and Wefer, 2013). Between 2005 and 2016 it was deployed on 17 research expeditions and drilled about 3 km into different types of geology including carbonate and crystalline rocks, gas hydrates, glacial tills, sands and gravel, glacial till and hemipelagic mud with an average recovery rate of about 70 %. We used the development and operational experiences of MARUM-MeBo70 for the development of a second generation drill rig MARUM-MeBo200. This drill rig is dedicated for conducting core drilling down to 200 m below sea floor. After successful sea trials in the North Sea in October 2014 the MeBo200 was used on a scientific expedition on the research vessel RV SONNE (SO247) in March/April 2016. During 12 deployments we drilled altogether 514 m in hemipelagic sediments with volcanic ashes as well as in muddy and sandy slide deposits off New Zealand. The average core recovery was about 54%. The maximum drilling depth was 105 m below sea floor. Developments for the MeBo drilling technology include the development of a pressure core barrel that was successfully deployed on two research expeditions so far. Bore hole logging adds to the coring capacity. Several autonomous logging probes have been developed in the last years for a deployment with MeBo in the logging while tripping mode - a sonic probe measuring in situ p-wave velocity being the latest development. Various bore hole monitoring systems where developed and deployed with the MeBo system. They allow for long-term monitoring of pressure variability within the sealed bore holes. References: Freudenthal, T and Wefer, G (2013) Drilling cores on the sea floor with the remote-controlled sea floor drilling rig MeBo. Geoscientific Instrumentation, Methods and Data Systems, 2(2). 329-337. doi:10.5194/gi-2-329-2013

Effects of red mud based passivator on the transformation of Cd fraction in acidic Cd-polluted paddy soil and Cd absorption in rice.

PubMed

Li, Hui; Liu, Yan; Zhou, Yaoyu; Zhang, Jiachao; Mao, Qiming; Yang, Yuan; Huang, Hongli; Liu, Zhaohui; Peng, Qinghui; Luo, Lin

2018-06-04

Highly effective, economical, and replicable ways of Cd-polluted paddy field remediation (in situ) are urgently needed. In this work, a yearlong field experiment (both early and late rice) was conducted to investigate the effects of red mud based passivator [red mud, diatomite, and lime (5:3:2)] on remediation of an acidic Cd-polluted paddy field in Hunan Province. Compared with the control, the addition of red mud based passivator in the early and late rice reduced Cd concentration in each part of the rice plant (with the most significant decrease rate of 59.18% and 72.11% for brown rice in the early rice and late rice seasons respectively). The effect of Cd reduction in the rice plant was persistent in the next growing season. The addition of red mud based passivator also reduced the exchangeable fraction of Cd in the soil and converted the exchangeable fraction into other unavailable fractions. This study demonstrated that the pH in acidic soil increased after the application of red mud based passivator. Furthermore, red mud based passivator had no effect on the concentrations of Olsen-K, Alkaline-N, Olsen-P in the soil, but increased rice grain yield. Overall, the results of this study indicated that the red mud based passivator at 0.6 kg m -2 could be a recommendation for Cd-polluted acidic paddy soil stabilization, and it would be a suitable method for remediation of Cd-polluted acidic paddy soil. Copyright © 2018 Elsevier B.V. All rights reserved.

Bacterial communities associated with production facilities of two newly drilled thermogenic natural gas wells in the Barnett Shale (Texas, USA).

PubMed

Davis, James P; Struchtemeyer, Christopher G; Elshahed, Mostafa S

2012-11-01

We monitored the bacterial communities in the gas-water separator and water storage tank of two newly drilled natural gas wells in the Barnett Shale in north central Texas, using a 16S rRNA gene pyrosequencing approach over a period of 6 months. Overall, the communities were composed mainly of moderately halophilic and halotolerant members of the phyla Firmicutes and Proteobacteria (classes Βeta-, Gamma-, and Epsilonproteobacteria) in both wells at all sampling times and locations. Many of the observed lineages were encountered in prior investigations of microbial communities from various fossil fluid formations and production facilities. In all of the samples, multiple H(2)S-producing lineages were encountered; belonging to the sulfate- and sulfur-reducing class Deltaproteobacteria, order Clostridiales, and phylum Synergistetes, as well as the thiosulfate-reducing order Halanaerobiales. The bacterial communities from the separator and tank samples bore little resemblance to the bacterial communities in the drilling mud and hydraulic-fracture waters that were used to drill these wells, suggesting the in situ development of the unique bacterial communities in such well components was in response to the prevalent geochemical conditions present. Conversely, comparison of the bacterial communities on temporal and spatial scales suggested the establishment of a core microbial community in each sampled location. The results provide the first overview of bacterial dynamics and colonization patterns in newly drilled, thermogenic natural gas wells and highlights patterns of spatial and temporal variability observed in bacterial communities in natural gas production facilities.

Program for the improvement of downhole drilling motor bearings and seals. Phase IV. Semi-annual report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tibbitts, G.A.; DeLafosse, P.H.; Black, A.

1980-07-01

Four main areas of development for the project are covered: design and fabrication of a dynamometer and a mud cooling system for the Bearing-Seal Package Test Facility; modification of the Bearing-Seal Package Test Facility based on test results; testing of new lubricant samples from Pacer Lubricants, Inc., in the Terra Tek High Temperature Lubricant Tester; and testing of new seal types in the Terra Tek Sea Tester. The Maurer Engineering Report, Semi-Annual Progress Report on Improvement of Downhole Motor Bearings and Seals by Jeff L. Barnwell, has been included as Appendix B.

Accuracy and borehole influences in pulsed neutron gamma density logging while drilling.

PubMed

Yu, Huawei; Sun, Jianmeng; Wang, Jiaxin; Gardner, Robin P

2011-09-01

A new pulsed neutron gamma density (NGD) logging has been developed to replace radioactive chemical sources in oil logging tools. The present paper describes studies of near and far density measurement accuracy of NGD logging at two spacings and the borehole influences using Monte-Carlo simulation. The results show that the accuracy of near density is not as good as far density. It is difficult to correct this for borehole effects by using conventional methods because both near and far density measurement is significantly sensitive to standoffs and mud properties. Copyright © 2011 Elsevier Ltd. All rights reserved.

Monitoring Well Installation and Groundwater Sampling and Analysis Plan at the USARC Training Reserve, 84th Division, Milwaukee, Wisconsin

DTIC Science & Technology

1988-11-01

paint chips at the sampling site. 0 Clean water tanks, pumps, mud pans, hoses, including hoses and tanks used to transfer water from source to drill rig...TO’ LCA , Filll I F’APCr,;I~- € C/ " rKL2PIrlA , ATTFNrIGN TO SMOKING. ALCOHOLF MFDrICATIONP AND FXPOSI.RE TO CARCINOGENS.1 ENERAL MEDICAl. HISTORY...A. General: 1. Place samples in core trough for visual inspection. After logging, place selected samples in sample jars or wood core boxes. 2. Seal

A study of iron mineral transformation to reduce red mud tailings.

PubMed

Li, L Y

2001-01-01

This study examines the effects of iron mineral transformation in an aluminum extraction process on the settling behavior, and the physical and chemical properties of the resulting red mud slurry that must be disposed of. By producing a red mud with a higher solid content, the total volume of mud slurry will also be reduced for a given alumina production rate and more caustic soda will be recovered. The settling behavior and the mineralogical, physical, and physico-chemical properties of one bauxite and three red muds processed under varying conditions were analyzed based on examination of the iron mineral transformations. The properties of red muds derived from the same bauxite can differ markedly due to variations in operating conditions of the Bayer process, such as temperature and the addition of a reducing agent. The settling of red mud can be improved by converting goethite into hematite and/or magnetite to produce a mud of larger particle size, smaller specific surface area, and larger specific gravity, characteristics which reduce the total volume of mud slurry to be disposed of and which allow for less potential contamination from caustic soda. This study also found that the by-product--Bayer sodalite--has the high exchange capacity for Na+ that might contribute to the long-term environmental problems.

The ICDP Dead Sea deep drill cores: records of climate change and tectonics in the Levant

NASA Astrophysics Data System (ADS)

Goldstein, S. L.; Stein, M.; Ben-Avraham, Z.; Agnon, A.; Ariztegui, D.; Brauer, A.; Haug, G. H.; Ito, E.; Kitagawa, H.; Torfstein, A.

2012-12-01

The Dead Sea drainage basin sits at the boundary of the Mediterranean and the Saharan climate zones, and the basin is formed by the Dead Sea transform fault. The ICDP-funded Dead Sea Deep Drilling Project recovered the longest and most complete paleo-environmental and paleo-seismic record in the Middle East, drilling holes of ~450 and ~350 meters in deep (~300 m below the lake level) and shallow sites (~3 m), respectively, and. The sediments record the evolving environmental conditions (e.g. droughts, rains, floods, dust-storms), as well as tectonics (earthquake layers). The core can be dated using 14C on organic materials, U-Th on inorganic aragonite, stable isotopes, and layer counting. They were opened, described, and XRF-scanned during June to November 2011, the first sampling party took place in July 2012, and study is now underway. Some important conclusions can already be drawn. The stratigraphy reflects the climate conditions. During wet climate intervals the lithology is typically varve-like laminated aragonite and detritus (aad), reflecting summer and winter seasons, respectively, and sequences of mud. Gypsum layers reflect more arid climate, and salt (halite) indicates extreme aridity. The Dead Sea expands during glacials, and the portion of the core that corresponds to the last glacial Lisan Formation above the shoreline is easily recognized in the core based on the common lithological sequence, and this allows us to infer a broad scale age model. Interglacials show all the lithologic facies (aad, mud, gypsum, salt), reflecting extreme climate variability, while glacials contain the aad, mud, and gypsum but lack salt layers. Thus we estimate that the deep site hole extends into MIS 7 (to ~200,000 years). Thin (up to several cm thick) seismic layers occur throughout the core, but thick (up to several meters) landslide deposits only occur during glacial intervals. The most dramatic discovery is evidence of an extreme dry interval during MIS 5 at the deep site. There is a ~40 cm thick interval of partly rounded pebbles in the core at ~235 m below the lake floor. It is the only clean pebbly unit in the core, and resembles a beach deposit. Below the layer there is ~45 meters of mainly salt. These observations indicate a severe dry interval during MIS 5. This observation has implications for the Middle East today, where the Dead Sea level is dropping at rates >1m/year, as all the countries in the area are using all the runoff. GCM models indicate a more arid future in the region. The core shows that the runoff nearly stopped during the last interglacial without human intervention. Dating is underway to constrain the timing of the extreme drydown.

Combined geophysical surveys and coring data to investigate the pattern of the Watukosek fault system around the Lusi eruption site, Indonesia.

NASA Astrophysics Data System (ADS)

Husein, Alwi; Mazzini, Adriano; Lupi, Matteo; Mauri, Guillaume; Kemna, Andreas; Hadi, Soffian; Santosa, Bagus

2016-04-01

The Lusi mud eruption is located in the Sidoarjo area, Indonesia and is continuously erupting hot mud since its birth in May 2006. The Watukosek fault system originates from the neighboring Arjuno-Welirang volcanic complex extending towards the NE of Java. After the 27-06-2006 M 6.3 earthquake this fault system was reactivated and hosted numerous hot mud eruptions in the Sidoarjo area. Until now, no targeted investigations have been conducted to understand the geometry of the faults system crossing the Lusi eruption site. A comprehensive combined electrical resistivity and self-potential (SP) survey was performed in the 7 km2 area inside the Lusi embankment that had been built to contain the erupted mud and to prevent flooding of the surrounding roads and settlements. The goal of the geophysical survey is to map the near-surface occurrence of the Watukosek fault system upon which Lusi resides, delineate its spatial pattern, and monitor its development. We completed six lines of resistivity measurements using Wenner configuration and SP measurements using roll-along technique. Three subparallel lines were located to the north and to the south of the main crater. Each line was approximately W-E oriented extending for ~1.26 km. The surveyed regions consist of mud breccia (containing clayey-silty-sandy mixture with clast up to ~10 cm in size). The geophysical data have been complemented with a N-S oriented profile consisting of 6 cores (~30m long) drilled in the dry area inside the Lusi embankment. The resistivity data were inverted into 2-D resistivity images with a maximum penetration depth of almost 200 m. These images consistently reveal a region of about 300 m in width (between 30-90 m depth) characterized by anomalous resistivities, which are lower than the values observed in the surrounding area. The results of the SP data correspond well with the resistivity profiles in the anomalous parts, which suggests that their origin is related to fluid flow paths in the subsurface. The coring results reveal varying thickness of the dry walkable mud overlying water saturated mud. The retrieved material also helped to constrain the subsidence depth of the original ground level that continuously collapses since the initiation of the eruption. These results have been used to complement the resistivity profiles and to provide a better model for the Watukosek fault system and the regional subsidence.

Microhole Coiled Tubing Bottom Hole Assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Don Macune

2008-06-30

The original objective of the project, to deliver an integrated 3 1/8-inch diameter Measurement While Drilling (MWD) and Logging While Drilling (LWD) system for drilling small boreholes using coiled tubing drilling, has been achieved. Two prototype systems have been assembled and tested in the lab. One of the systems has been successfully tested downhole in a conventional rotary drilling environment. Development of the 3 1/8-inch system has also lead to development and commercialization of a slightly larger 3.5-inch diameter system. We are presently filling customer orders for the 3.5-inch system while continuing with commercialization of the 3 1/8-inch system. Themore » equipment developed by this project will be offered for sale to multiple service providers around the world, enabling the more rapid expansion of both coiled tubing drilling and conventional small diameter drilling. The project was based on the reuse of existing technology whenever possible in order to minimize development costs, time, and risks. The project was begun initially by Ultima Labs, at the time a small company ({approx}12 employees) which had successfully developed a number of products for larger oil well service companies. In September, 2006, approximately 20 months after inception of the project, Ultima Labs was acquired by Sondex plc, a worldwide manufacturer of downhole instrumentation for cased hole and drilling applications. The acquisition provided access to proven technology for mud pulse telemetry, downhole directional and natural gamma ray measurements, and surface data acquisition and processing, as well as a global sales and support network. The acquisition accelerated commercialization through existing Sondex customers. Customer demand resulted in changes to the product specification to support hotter (150 C) and deeper drilling (20,000 psi pressure) than originally proposed. The Sondex acquisition resulted in some project delays as the resistivity collar was interfaced to a different MWD system and also as the mechanical design was revised for the new pressure requirements. However, the Sondex acquisition has resulted in a more robust system, secure funding for completion of the project, and more rapid commercialization.« less

The Georges Bank monitoring program 1985; analysis of trace metals in bottom sediments during the third year of monitoring

USGS Publications Warehouse

Bothner, Michael H.; Rendigs, R. R.; Campbell, Esma; Doughten, M.W.; Parmenter, C.M.; O'Dell, C. H.; DiLisio, G.P.; Johnson, R.G.; Gillison, J.R.; Rait, Norma

1986-01-01

Of the 12 elements analyzed in bulk (undifferentiated) sediments collected adjacent to drilling rigs on Georges Bank, only barium was found to increase in concentration during the period when eight exploratory wells were drilled (July 1981 until September 1982). The maximum postdrilling concentration of barium (a major element in drilling mud) reached 172 ppm in bulk sediments near the drill site in block 410. This concentration is higher than the predrilling concentration at this location by a factor of 5.9. This maximum barium concentration is within the range of predrilling concentrations (28-300 ppm) measured in various sediment types from the regional stations of this program. No drilling-related changes in the concentrations of the 11 other metals have been observed in bulk sediments at any of the locations sampled in this program. We estimate that about 25 percent of the barite discharged at block 312 was present in the sediments within 6 km of the rig, 4 weeks after drilling was completed at this location (drilling period was December 8, 1981-June 27, 1982). For almost a year following completion of this well, the inventory of barite decreased rapidly, with a half-life of 0.34 year. During the next year, the inventory decreased at a slower rate (half-life of 3.4 years). The faster rate probably reflects resuspension and sediment transport of bariterich material residing at the sediment surface. Elevated barium concentrations in post-drilling sediment-trap samples from block 312 indicate that such resuspension can occur up to at least 25 m above the sea floor. As the remaining barite particles are reworked deeper into the sediments by currents and bioturbation, removal by sediment-transport processes is slower. The barite discharged during the exploratory phase of drilling is associated with the fine fraction of sediment and is widely distributed around the bank. We found evidence for barium transport to Great South Channel, 115 km west of the drilling, and to stations 2 and 3, 35 km east of the easternmost drilling site. Small increases in barium concentrations, present in the fine fraction of sediment only, were measured also at the heads of both Lydonia and Oceanographer Canyons, located 8 and 39 km, respectively, seaward of the nearest exploratory well.

Radiological restrictions of using red mud as building material additive.

PubMed

Gu, Hannian; Wang, Ning; Liu, Shirong

2012-09-01

Red mud remains as residue from the processing of bauxite using different methods. The chemical composition of red mud varies widely with respect to the types of bauxite ore and processing parameters. Red mud samples from Guizhou, China, were investigated using a X-ray fluorescence spectroscope, a quadrupole inductively coupled plasma mass spectrometer and a electron probe micro-analyzer. The results showed that red mud consisted of eight main chemical components--CaO, Al(2)O(3), SiO(2), Fe(2)O(3), TiO(2), Na(2)O, K(2)O and MgO--and dozens of trace elements, including natural radioactive elements, such as uranium and thorium. Gamma spectrometric analysis showed that the values of internal exposure index I (Ra) and external exposure index I (γ) of Guizhou red mud were 1.1-2.4 and 2.3-3.5 respectively. Thus, it should not be used as a main building material indiscriminately. The amount of red mud from Guizhou when it is used for main building materials in China should be less than 28-44%.

Particularies of recultivation of bore muds on oil-gas fields of Tyumen region

NASA Astrophysics Data System (ADS)

Petuhova, V. S.; Skipin, L. N.; Skipin, D. L.; Gaevaya, E. V.

2017-10-01

The article reflects negative physical and chemical properties of the bore muds in respect to Tyumen region (high dispersion, swelling ability, ash structure, crust formation, low filterability, a high degree of salinization, alkalinity and toxicity). Indicated properties are mainly stipulated by the increased content of exchangeable sodium in the absorbing complex and by the presence of soda in aqueous solution. The source of absorbed sodium and soda in water extract is the use of caustic soda in the drilling mixture. It was found out that these negative properties are illuminated using coagulant in a form of phosphogypsum - waste of chemical industry. Necessity in the nitrogen for the bean cultures-phytomeliorants is provided at the expense of legume bacteria in a form of the rizotorphin formulation. It is worth noting that growing of legume bacteria in extremely salted breeding ground on the leguminous agar has allowed choosing the most salt resistant species among the numerous strains of Melilotus officinalis and medicago. The presence of phosphorus in phosphogypsum positively influences the productivity of leguminous crops in the beginning of recultivation.

Scientific Studies in Support of Shutting In the Macondo Well (Deepwater Horizon) Blowout, Gulf of Mexico (Invited)

NASA Astrophysics Data System (ADS)

Hickman, S.; Mooney, W. D.; Hsieh, P. A.; Enomoto, C.; Nelson, P. H.; McNutt, M.

2010-12-01

Scientists, engineers and managers from BP, other private companies, universities, government research labs and a broad spectrum of federal agencies have formed a unique cooperative working relationship in responding to the Macondo oil well (Deepwater Horizon) blowout. Among the many activities performed during this effort, U.S. Geological Survey personnel evaluated the potential geologic hazard of shutting in the Macondo well at the sea floor, and collectively decided, with others, the conditions under which it could be safely undertaken. These hazards included the possible loss of wellbore integrity under the anticipated high shut-in pressures, potentially leading to new pathways for hydrocarbon release to the Gulf of Mexico through upward hydraulic fracture propagation and/or soft sediment erosion initiating at possible leak points in the cemented casing. This hazard evaluation required analysis of 2D and 3D seismic surveys, seafloor bathymetry, pressure transient tests, geophysical well logs, in-situ stress (“leak-off”) tests and drilling data (e.g., mud logs) to assess the geological, hydrological and geomechanical conditions at and around the Macondo well. After the well was successfully capped and shut in by BP on July 15, a variety of monitoring practices were put into place to guard against further leaks into the Gulf. These monitoring activities included acquisition of wellhead pressure data, marine multi-channel seismic profiles, sea-floor and sea-surface sonar surveys (the latter using the NOAA RV/Pisces), and wellhead visual/acoustic monitoring. Scientists and engineers from BP, outside consultants, government agencies and the university community then worked together to continuously evaluate these data to ensure that the well remained safely shut in until reservoir pressures were suppressed (“killed”) with heavy drilling mud and the well was sealed with cement. This effort to shut in and then permanently seal the blown-out Macondo well has involved an unprecedented level of interaction, collaboration and coordination among scientists, engineers, managers and emergency response officials, and will hopefully lead to improved methodologies and approaches to assessing and then mitigating hazards posed by deepwater drilling.

Deep Subsurface Microbial Communities Shaped by the Chicxulub Impactor

NASA Astrophysics Data System (ADS)

Cockell, C. S.; Coolen, M.; Schaefer, B.; Grice, K.; Gulick, S. P. S.; Morgan, J. V.; Kring, D. A.; Osinski, G.

2017-12-01

Fresh core material was obtained by drilling of the Chicxulub impact crater during IODP-ICDP Expedition 364 to assess the present-day biosphere in the crater structure. Cell enumerations through the core show that beneath the post-impact sedimentary rock there is a region of enhanced cell abundance that corresponds to the upper impact suevite layer (Units 1G/2A). We also observed a peak in cell numbers in samples at the bottom of suevite Unit 2C and between the suevitic and grainitoid interface (Unit 3/4). These patterns may reflect preferential movement of fluid and/or availability of nutrients and energy at interfaces. 16S rDNA analysis allows us to rule out contamination of the suevite material since no taxa associated with the drilling mud were observed. Two hundred and fifty microbial enrichments were established using diverse culture media for heterotrophs, autotrophs and chemolithotrophs at temperatures consistent with measured core temperatures. Six yielded growth in the breccia, lower breccia and upper granitoid layer and they affiliated with Acidiphilium, Thermoanaerobacteracea and Desulfohalbiaceae. The latter exhibited visible microbial sulfate-reduction. By contrast, the granitoid material exhibited low cell abundances, most samples were below direct cell detection. DNA extraction revealed pervasive low level contamination by drilling mud taxa, consistent with the highly fractured, high porosity of the impact-shocked granitoids. Few taxa can be attributed to an indigenous biota and no enrichments (at 60 and 70°C) yielded growth. These data show that even with a porosity approximately an order of magnitude greater than most unshocked granites, the uplifted granites have not experienced sufficient fluid flow to establish a significant deep biosphere. Paleosterilisation of the material during impact may have re-set colonisation and the material may have originally been below the depth at which temperatures exceeded the upper temperature limit for life. These data show that the deep biosphere can preserve the imprint of catastrophe long after these events. In this case, the distribution of deep subsurface microbial communities reflects the lithological sequence established during the substantial impact-induced geological rearrangements that occurred in the first hours of the Cenozoic.

Clear as Mud: Changes in Paleoshelf Environments and Deposition Rates at Medford, New Jersey during the Paleocene-Eocene Thermal Maximum

NASA Astrophysics Data System (ADS)

Podrecca, L.; Miller, K. G.; Wright, J. D.; Browning, J. V.; Emge, T.

2017-12-01

The Paleocene-Eocene boundary marks a time of swift global climatic change. Constraining the timeframe of this event is a first order question necessary for ascertaining the origin of the event and the potential for its use as an analog for modern climate change. The New Jersey shelf sediments of the Marlboro Formation records this time period with exceptionally thick (5-15m) records of the period of global low carbon isotopic values ("the core") which requires minimum sedimentation rates of 10's cm/kyr. Rhythmic layers have been previously reported from Wilson Lake & Millville, NJ (IODP Leg 174AX). These structures coined "laminae couplets" consist of semi-periodic 1-2mm thick raised laminations separated by matrix of varying width (averaging 1.8cm). These have been dismissed as artifacts of drilling "biscuits". We report here on a series of shallow auger cores drilled on a transect at Medford, NJ, without using drilling fluid. These cores also show a similar set of structures on the 2cm scale verifying that they are primary depositional features. The mm width laminae in the auger core show remarkable swelling within minutes of splitting. XRD, XRF, bulk carbonate geochemistry, and grain size analysis have been determined at regular depth intervals throughout the core. We have analyzed differences in these parameters between the laminae and interbedded matrix material, as well as across the transect as a whole. In general, the Marlboro formation at this updip location consists of micaceous, lignitic, very clayey silt (mean size 6 micrometers) with occasional organic debris indicating proximal deposition from a fluvial system. Paleodepth of 40m and normal marine salinities are estimated using a paleoslope model and the presence of common though not abundant planktonic foraminifera. We discuss a model of deposition for the Marlboro Formation as fluid mud (nearbed suspension flows) associated with the "Appalachian Amazon" alluding toward the finer grained inter-laminae representing settling events. These may be either hemipelagics associated with episodic flood events or seasonal periods of in-river sediment discharge and the benthic salinity front.

A preliminary evaluation of the nonfuel mineral potential of Somalia

USGS Publications Warehouse

Greenwood, W.R.

1982-01-01

Additional exploration in Somalia is warranted for a wide variety of metallic and nonmetallic deposits. In Precambrian rocks, deposit types favorable for exploration include: a banded iron formation; platinum-bearing mafic-ultramafic complexes; tin-bearing quartz veins; phosphorite; stratabound base-metal deposits; uranium associated with Precambrian(?) syenite; apatite, molybdenum, and alumina in alkalic rocks; Jurassic and Cretaceous black shales; possible bedded-barite and massive base- and precious-metal sulfide deposits; vein barite in Tertiary rocks in fault zones; sepiolite and bentonite for drilling muds and other industrial uses; celestite; possible Tertiary zeolite; and uranium deposits. Several of these deposit types could be Jointly developed and integrated into domestic industries; for example, phosphate and gypsum, or bentonite for pelletized iron from the banded iron deposits. Other deposits such as barite and sepiolite are of value because of their proximity to major drilling operations in the Arabian Gulf. Still other deposits, such as alumina and banded iron, might be marketable because of proximity to aluminum and iron-refining industries now being constructed in Saudi Arabia. Some deposits, such as celestite, can be developed with little capital investment; others, such as the iron deposits, would require large capital commitments. Exploration and evaluation for many of these deposits can be accomplished by Somali geologists with a few advisors. Most of the deposits require feasibility studies conducted by teams of economic geologists, extractive metallurgists, and economists. Some marginal deposits could be exploited if cooperative development schemes could be negotiated with governments in nearby countries.

Utilization of red mud and Pb/Zn smelter waste for the synthesis of a red mud-based cementitious material.

PubMed

Li, Yuan-Cheng; Min, Xiao-Bo; Ke, Yong; Chai, Li-Yuan; Shi, Mei-Qing; Tang, Chong-Jian; Wang, Qing-Wei; Liang, Yan-Jie; Lei, Jie; Liu, De-Gang

2018-02-15

A new method in which Pb/Zn smelter waste containing arsenic and heavy metals (arsenic sludge), red mud and lime are utilized to prepare red mud-based cementitious material (RCM) is proposed in this study. XRD, SEM, FTIR and unconfined compressive strength (UCS) tests were employed to assess the physicochemical properties of RCM. In addition, ettringite and iron oxide-containing ettringite were used to study the hydration mechanism of RCM. The results show that the UCS of the RCM (red mud+arsenic sludge+lime) was higher than that of the binder (red mud+arsenic sludge). When the mass ratio of m (binder): m (lime) was 94:6 and then maintained 28days at ambient temperature, the UCS reached 12.05MPa. The red mud has potential cementitious characteristics, and the major source of those characteristics was the aluminium oxide. In the red mud-arsenic sludge-lime system, aluminium oxide was effectively activated by lime and gypsum to form complex hydration products. Some of the aluminium in ettringite was replaced by iron to form calcium sulfoferrite hydrate. The BCR and leaching toxicity results show that the leaching concentration was strongly dependent on the chemical speciation of arsenic and the hydration products. Therefore, the investigated red mud and arsenic sludge can be successfully utilized in cement composites to create a red mud-based cementitious material. Copyright © 2017 Elsevier B.V. All rights reserved.

The effect of amino acid lysine and methionine addition on feed toward the growth and retention on mud crab (Scylla serrata)

NASA Astrophysics Data System (ADS)

Alissianto, Y. R.; Sandriani, Z. A.; Rahardja, B. S.; Agustono; Rozi

2018-04-01

High market demand of mud crab (Scylla serrata) encourages farmers to increase the production of mud crab. However, mud crab can not synthesize essential amino acids, so it is necessary to supply essential amino acids such as lysine and methionine in the diet. This study aims to determine the effect of lysine and methionine on feeds to increase growth and retention of mud crabs (Scylla serrata). In this study the amount of lysine amino acid and methionine added to the trash fish diet were: P0 (0: 0%); P1 (0.75: 0.75%); P2 (1: 1%); P3 (1.25: 1.25%); P4 (1.5: 1.5%) with the ratio of lysine and methionine 1: 1. The parameters observed in this study were Survival Rate (SR), Specific Growth Rate (SGR), Feed Conversion Ratio (FCR), Efficiency Feed (EF), protein retention and energy retention. The results of the 35-day maintenance study showed significant differences (P <0.05) against Specific Growth Rate (SGR), Feed Conversion Ratio (FCR), Efficiency Feed (EF), protein retention and no significant effect (P> 0.05) on energy retention and Survival Rate (SR) on mud crab. The best results in this study were found in P4 treatment with addition of lysine amino acids and methionine (1.5: 1.5%).

Elemental Geochemistry of Samples From Fault Segments of the San Andreas Fault Observatory at Depth (SAFOD) Drill Hole

NASA Astrophysics Data System (ADS)

Tourscher, S. N.; Schleicher, A. M.; van der Pluijm, B. A.; Warr, L. N.

2006-12-01

Elemental geochemistry of mudrock samples from phase 2 drilling of the San Andreas Fault Observatory at Depth (SAFOD) is presented from bore hole depths of 3066 m to 3169 m and from 3292 m to 3368 m, which contain a creeping section and main trace of the fault, respectively. In addition to preparation and analysis of whole rock sample, fault grains with neomineralized, polished surfaces were hand picked from well-washed whole rock samples, minimizing the potential contamination from drilling mud and steel shavings. The separated fractions were washed in deionized water, powdered using a mortar and pestle, and analyzed using an Inductively Coupled Plasma- Optical Emission Spectrometer for major and minor elements. Based on oxide data results, systematic differences in element concentrations are observed between the whole rock and fault rock. Two groupings of data points are distinguishable in the regions containing the main trace of the fault, a shallow part (3292- 3316 m) and a deeper section (3320-3368 m). Applying the isocon method, assuming Zr and Ti to be immobile elements in these samples, indicates a volume loss of more than 30 percent in the shallow part and about 23 percent in the deep part of the main trace. These changes are minimum estimates of fault-related volume loss, because the whole rock from drilling samples contains variable amount of fault rock as well. Minimum estimates for volume loss in the creeping section of the fault are more than 50 percent when using the isocon method, comparing whole rock to plucked fault rock. The majority of the volume loss in the fault rocks is due to the dissolution and loss of silica, potassium, aluminum, sodium and calcium, whereas (based on oxide data) the mineralized surfaces of fractures appear to be enriched in Fe and Mg. The large amount of element mobility within these fault traces suggests extensive circulation of hydrous fluids along fractures that was responsible for progressive dissolution and leaching of the wall rock during faulting.

Red mud enhances methanogenesis with the simultaneous improvement of hydrolysis-acidification and electrical conductivity.

PubMed

Ye, Jie; Hu, Andong; Ren, Guoping; Zhou, Ting; Zhang, Guangming; Zhou, Shungui

2018-01-01

The role of red mud in the improvement of methanogenesis during sludge anaerobic digestion was innovatively investigated in this study. The results demonstrated that the addition of 20g/L red mud resulted in a 35.5% increase in methane accumulation. Red mud effectively promoted the hydrolysis-acidification of organic compounds in the sludge, which resulted in the increase of protein, polysaccharide, and VFAs by 5.1-94.5%. The activities of key enzymes were improved by 41.4-257.3%. Electrochemical measurements presented direct evidence that the electrical conductivity was significantly improved with red mud. More conductive magnetite was formed during the secondary mineralization after Fe(III) reduction by Fe (III)-reducing genes such as Clostridiaceae and Ruminococcaceae. The higher conductivity enhanced the electron transfer between the syntrophic bacteria (Geobacteraceae) and methanogens (Methanosaeta and Methanosarcina), and then improved the methanogenesis. This research provides a novel perspective on the synergism between sludge and red mud for methane production. Copyright © 2017 Elsevier Ltd. All rights reserved.

A comparison of different turbidite plays in the Yinggehai and Qiongdongnan Basins of the South China Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cardwell, R.K.; Norris, J.W.

1996-12-31

Three different types of turbidite plays have been drilled in the Yinggehai and Qiongdongnan basins of the South China Sea: slope fan turbidites, bottomset turbidites, and channel fill turbidites. Each play type has a distinctive well log signature, lithology, seismic reflector geometry, and reservoir character. Slope fan turbidites are encountered in the YA 21-1-3 well. Well logs are characterized by a ratty SP curve, and mud logs indicate that the turbidites are composed of up to 80 m of sands and silts. Seismic profiles show that these turbidites are found in a distributary channel and levee system on the shelf.more » Bottomset turbidites are encountered in the LD 15-1-1 well. Well logs are characterized by an upward coarsening SP curve, and mud logs indicate that the turbidites are composed of up to 10 m of silty sand. Seismic profiles show these turbidites are deposited by the slumping of shelf sands during a continuous lowstand progradation. Channel fill turbidites are encountered in the LD 30-1-1 well. Well logs are characterized by a blocky SP curve, and mud logs indicate that the turbidites are composed of up to 100 m of massive sand. Seismic profiles show that these turbidites are associated with channel systems that trend parallel to the local basin axis. Distinct cut and fill geometries indicate that the turbidite sands were deposited in a preexisting channel cut.« less

A comparison of different turbidite plays in the Yinggehai and Qiongdongnan Basins of the South China Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cardwell, R.K.; Norris, J.W.

1996-01-01

Three different types of turbidite plays have been drilled in the Yinggehai and Qiongdongnan basins of the South China Sea: slope fan turbidites, bottomset turbidites, and channel fill turbidites. Each play type has a distinctive well log signature, lithology, seismic reflector geometry, and reservoir character. Slope fan turbidites are encountered in the YA 21-1-3 well. Well logs are characterized by a ratty SP curve, and mud logs indicate that the turbidites are composed of up to 80 m of sands and silts. Seismic profiles show that these turbidites are found in a distributary channel and levee system on the shelf.more » Bottomset turbidites are encountered in the LD 15-1-1 well. Well logs are characterized by an upward coarsening SP curve, and mud logs indicate that the turbidites are composed of up to 10 m of silty sand. Seismic profiles show these turbidites are deposited by the slumping of shelf sands during a continuous lowstand progradation. Channel fill turbidites are encountered in the LD 30-1-1 well. Well logs are characterized by a blocky SP curve, and mud logs indicate that the turbidites are composed of up to 100 m of massive sand. Seismic profiles show that these turbidites are associated with channel systems that trend parallel to the local basin axis. Distinct cut and fill geometries indicate that the turbidite sands were deposited in a preexisting channel cut.« less

How PEMEX engineered a deep well completion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antimo A., J.C.

1971-09-01

Completion and testing of Petroleos Mexicano's W. Reynosa Well No. 1 in the NE. Frontier District south of the Texas border required engineering innovation to combat the 375/sup 0/F temperatures and pressures near 18,000 psi. Drilled to nearly 18,000 ft, the well was completed and tested below 17,000 ft. Completion plans were designed to determine the economic importance of the reservoir and to provide information and experience in planning future completions to 20,000 ft and deeper. Interval selection was based in part on data acquired during drilling, including lithology, geologic age, rock characteristics, and sensitivity to damage caused by drillingmore » fluids. A set of logs was obtained and evaluated by computer in correlation with mud-log and pressure data. The logs also were correlated with logs from other wells in the area. Pressure gradients in the Reynosa field indicated the possibility of pressures on the order of 10,000 psi, and required the use of specially designed valves rated to 20,000 psi, in conjunction with a casinghead that would permit drilling to the projected depth. A choke manifold consisted of an interchangeable, manually operated positive choke and a set of automatic adjustable chokes. Well conditioning, including cementing, perforating, and well plugging are described.« less

Environmental concerns and future oil and gas developments in Coastal Wetlands of Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

John, C.J.; Harder, B.J.; Groat, C.G.

1993-09-01

Recent studies have confirmed that much oil and natural gas have been overlooked and increases in future recoverable reserves will come from drilling in these areas. Increased production will result from identifying unexploited compartmentalized reservoirs, new infield reservoirs, and bypassed reservoirs, and by using enhanced recovery technologies for hydrocarbon recovery in incompletely drained reservoirs previously left unproduced for economic reasons. Most of southern Louisiana's hydrocarbon reserves underlie coastal wetland areas of the state. Major environmental concerns associated with the future development of existing reserves are canal dredging and destruction of wildlife habitat, use and disposal of oil-based muds, mitigation formore » wetland damage, and the recent emerging issue of surface contamination by naturally occurring radioactive materials with potential liabilities and future remedial regulation. To reduce wetland environmental damage caused by access canals to drilling sites, the Coastal Management Division of the Louisiana Department of Natural Resources instituted a geologic reviews program to review drilling permit application in the coastal wetlands. This process provides a mechanism for state and federal agencies to comment on the requested drilling permit. As a result of this process, the total average wetland disturbed area has been reduced from 767 ac per year in 1982 to approximately 76 ac per year in 1991. Average lengths of access canals also have been reduced by approximately 78% during the period. Oil and gas companies are becoming increasingly aware of the environmental consequences of drilling in wetlands and are considering them in planning for development activities. In the current climate of increasing public consciousness about the environment, addressing environmental concerns in the planning state will go a long way in helping alleviate future environmental problems.« less

Geomechanical Engineering Concepts Applied to Deep Borehole Disposal Wells

NASA Astrophysics Data System (ADS)

Herrick, C. G.; Haimson, B. C.; Lee, M.

2015-12-01

Deep borehole disposal (DBD) of certain defense-generated radioactive waste forms is being considered by the US Department of Energy (DOE) as an alternative to mined repositories. The 17 inch diameter vertical boreholes are planned to be drilled in crystalline basement rock. As part of an initial field test program, the DOE will drill a demonstration borehole, to be used to test equipment for handling and emplacing prototype nonradioactive waste containers, and a second smaller diameter borehole, to be used for site characterization. Both boreholes will be drilled to a depth of 5 km. Construction of such boreholes is expected to be complex because of their overall length, large diameter, and anticipated downhole conditions of high temperatures, pore pressures, and stress regimes. It is believed that successful development of DBD boreholes can only be accomplished if geologic and tectonic conditions are characterized and drill activities are designed based on that understanding. Our study focuses primarily on using the in situ state of stress to mitigate borehole wall failure, whether tensile or compressive. The measured stresses, or their constrained estimates, will include pore pressure, the vertical stress, the horizontal stresses and orientations, and thermally induced stresses. Pore pressure will be measured directly or indirectly. Horizontal stresses will be estimated from hydraulic fracturing tests, leak off tests, and breakout characteristics. Understanding the site stress condition along with the rock's strength characteristics will aid in the optimization of mud weight and casing design required to control borehole wall failure and other drilling problems.Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. SAND2015-6552A

The effect of mud therapy on pain relief in patients with knee osteoarthritis: a meta-analysis of randomized controlled trials.

PubMed

Liu, Hua; Zeng, Chao; Gao, Shu-guang; Yang, Tuo; Luo, Wei; Li, Yu-sheng; Xiong, Yi-lin; Sun, Jin-peng; Lei, Guang-hua

2013-10-01

A meta-analysis was conducted to examine the effect of mud therapy on pain relief in patients with knee osteoarthritis (OA). A detailed search of PubMed®/MEDLINE® was undertaken to identify randomized controlled trials and prospective comparative studies published before 9 March 2013 that compared mud therapy with control group treatments in patients with knee OA. A quantitative meta-analysis of seven studies (410 patients) was performed. There was a significant difference between the groups in the visual analogue scale pain score (standardized mean difference [SMD] -0.73) and Western Ontario and McMaster Universities Osteoarthritis Index pain score (SMD -0.30), with differences in favour of mud therapy. Mud therapy is a favourable option for pain relief in patients with knee OA. Additional high-quality randomized controlled trials need to be conducted to explore this issue further and to confirm this conclusion.

The wister mud pot lineament: Southeastward extension or abandoned strand of the San Andreas fault?

USGS Publications Warehouse

Lynch, D.K.; Hudnut, K.W.

2008-01-01

We present the results of a survey of mud pots in the Wister Unit of the Imperial Wildlife Area. Thirty-three mud pots, pot clusters, or related geothermal vents (hundreds of pots in all) were identified, and most were found to cluster along a northwest-trending line that is more or less coincident with the postulated Sand Hills fault. An extrapolation of the trace of the San Andreas fault southeastward from its accepted terminus north of Bombay Beach very nearly coincides with the mud pot lineament and may represent a surface manifestation of the San Andreas fault southeast of the Salton Sea. Additionally, a recent survey of vents near Mullet Island in the Salton Sea revealed eight areas along a northwest-striking line where gas was bubbling up through the water and in two cases hot mud and water were being violently ejected.

Indian Wells Valley Deep Well Drilling Project Volume 1. Data Report (1990-1992)

DTIC Science & Technology

1995-10-01

mud. OoL ro t.t. (0.) T-IP -o . los. I.... !IT00 •q/0 70.0001 0) f.0. co 2. 0I/0-*0 Ttot0 T0.0.*0.00 0,0000.00. I 1000 000O: I i - 0000. 0nFr.O Solor ...Date/Time Sample Date Analyses Collected: 91/02/02/1200 Received @ Lab: 91/02/02/1200 Completed: 91/02/26 System System Name: NORTH AMERICAN CHEMICAL...Lab: 91/02/02 Observed: Yes System Name: North American Chemical ISystem Number: Description of Sampling Point: I.W.V. Test Well Name/No. of Sample

Methods of performing downhole operations using orbital vibrator energy sources

DOEpatents

Cole, Jack H.; Weinberg, David M.; Wilson, Dennis R.

2004-02-17

Methods of performing down hole operations in a wellbore. A vibrational source is positioned within a tubular member such that an annulus is formed between the vibrational source and an interior surface of the tubular member. A fluid medium, such as high bulk modulus drilling mud, is disposed within the annulus. The vibrational source forms a fluid coupling with the tubular member through the fluid medium to transfer vibrational energy to the tubular member. The vibrational energy may be used, for example, to free a stuck tubular, consolidate a cement slurry and/or detect voids within a cement slurry prior to the curing thereof.

Chemistry and Isotopic Composition of Slab-Derived Fluids from Serpentine Mud Volcanoes in the Mariana Forearc

NASA Astrophysics Data System (ADS)

Ryan, J. G.; Menzies, C. D.; Teagle, D. A. H.; Price, R. E.; Sissmann, O.; Wheat, C. G.; Boyce, A.

2017-12-01

Geological processes at subduction zone margins control seismicity, plutonism/ volcanism, and geochemical cycling between the oceans, crust, and mantle. The down-going plate experiences dehydration, and associated metamorphism alters the physical properties of the plate interface and mantle wedge. The Mariana convergent margin is non-accretionary, and serpentinite mud volcanoes in the pervasively faulted forearc mark loci of fluid and material egress from the subducting slab and forearc mantle. IODP Expedition 366 drilled into three serpentinite mud volcanoes: Yinazao (13 km depth-to-slab); Fantangisña (14 km) and Asùt Tesoru (18 km), allowing comparison with the previously drilled South Chamorro (18 km) and Conical (19 km) Seamounts. We use the changes in chemistry and isotopic composition of porefluids between seamounts to trace the evolution of the downgoing slab and water-rock interactions in the overlying mantle wedge. Boron isotopes allow investigation of the processes governing prograde metamorphism in the downgoing slab, and combined with O, D/H and Sr isotopes are used to assess the balance between seawater and dehydration fluids during mantle wedge serpentinization. The shallowest depth-to-slab seamounts, Yinazao and Fantangisña, are associated with Ca and Sr-enriched, but otherwise solute poor, low alkalinity fluids of pH 11. In contrast, the Asùt Tesoru seamount fluids are markedly higher in Na and Cl, as well as in tracers like B and K, which are associated with the breakdown of slab sheet silicate phases, and are depleted in Ca and Sr compared to seawater. Higher DIC at this site is attributed to slab carbonate decomposition. The elevated pH ( 12.5) is likely due to Fe2+ oxidation, producing H2 and OH- during serpentinization. Asùt Tesoru porefluids are similar to those studied at South Charmorro and Conical Seamounts that have similar depths to slab, although those sites have distinctly lower Na and Cl, but 3-4 times higher B concentrations. These changes between sites reflect metamorphic prograde reactions on the downgoing plate with increasing depth (P-T°). At shallow depths sediment compaction and opal CT dehydration dominate; intermediate depths are characterised by clay diagenesis and desorbed water release; and at greater depths decarbonation and clay decomposition are dominant.

Chemical, mineralogical, and isotopic characteristics of mud from the LUSI mud volcano, Sidoarjo, East Java, Indonesia: implications for the environment, public health, and eruption processes

NASA Astrophysics Data System (ADS)

Plumlee, G. S.; Casadevall, T. J.; Wibowo, H. T.; Rosenbauer, R. J.; Johnson, C. A.; Breit, G. N.; Hageman, P. L.; Wolf, R. E.; Morman, S. A.

2009-12-01

On May 29, 2006, mud and gases began erupting from a vent 150 meters away from a gas exploration well near Sidoarjo, East Java, Indonesia. The eruption, called the LUSI mud volcano, has continued at rates as high as 160,000 m3 per day. At the request of the United States Department of State, the U.S. Geological Survey (USGS) has been providing technical assistance to the Indonesian Government on the geological and geochemical aspects of the mud eruption. This paper will present analytical results of mud samples collected in Sept. 2007 and Nov. 2008, and interpretive findings based on the analytical results. The 2007 mud sample contains high proportions of particles that could be ingestible by hand-mouth transmission (~98 vol % <250 microns,), inhalable into the upper respiratory tract (~80 vol % <10 microns), and respirable into the lung alveoli (~ 40 vol % <2.5 microns), so the mud and dust from the dried mud could be readily taken up by exposed individuals. Our results confirm those of a previous study that the levels of potentially toxic heavy metals or metalloids in the mud are low. A complex mixture of organic compounds in the mud is likely derived from petroleum source rocks. Although the 2007 mud sample contains several percent iron sulfides, net acid production tests indicate that enough carbonate material is also present to prevent the mud from becoming acid-generating due to weathering and sulfide oxidation in the near-surface environment. Water derived from settling mud deposits may have the potential to adversely affect the quality of surface- or groundwater sources for drinking water, due to high levels of fluoride, nitrate, iron, manganese, aluminum, sulfate, chloride, and total dissolved solids. The very high nitrate levels in the waters contained within the mud may present a source of nutrients that could enhance algal blooms and resulting adverse impacts such as hypoxia in fresh-water and marine ecosystems into which some of the mud is being discharged. In agreement with previous studies, water separated from the 2007 mud sample is compositionally and isotopically compatible with an origin as sedimentary formation water. The iron disulfide fraction of the mud sample is isotopically light, and likely formed by bacterial sulfate reduction during diagenesis of clay-rich rocks from which the mud was derived. A smaller, isotopically heavy monosulfide fraction likely formed later by thermogenic reduction of formation-water sulfate to sulfide and reaction of the resulting sulfide with reactive iron in the mud. Additional linked earth science and public health studies are needed to more fully understand eruption processes, and the potential environmental and health consequences of the erupting mud, waters, and gases, and of the accumulating mud deposits.

Prospecting for Natural Gas Gydrate in the Orca & Choctaw Basins in the Northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Cook, A.; Hillman, J. I. T.; Sawyer, D.; Frye, M.; Palmes, S.; Shedd, W. W.

2016-12-01

The Orca and Choctaw salt bounded mini-basins, which occur in 1.5 to 2.5 km water depth on the northern Gulf of Mexico slope, are currently under consideration as an IODP scientific drilling location for coarse-grained natural gas hydrate systems. We use a 3D seismic dataset for gas hydrate prospecting that covers parts of eleven lease blocks ( 200 km2) in the Walker Ridge protraction area. The study area includes the southern section of the Orca Basin and a smaller section of the northern Choctaw Basin. We have mapped a discontinuous bottom-simulating reflection (BSR) over nearly 30% of our seismic dataset, which varies significantly in both amplitude and depth throughout the area. The southeastern section of our dataset contains three positive impedance amplitude horizons with possible phase reversals at the BSR. Detailed mapping in the area also reveals at the base of gas hydrate stability, a complicated intercalation of an east-west trending fault system and an amalgamated deepwater depositional system comprising channel levee deposits and turbidite sheet sands. Three industry wells drilled in the southwestern section of our study area indicate that the sedimentary sequence infilling the basins consists of predominantly mud rich units with interbedded turbidite sands, forming a 2 km thick supra-salt sequence of late Miocene to Pleistocene sediments. Two of the industry wells have strong evidence for natural gas hydrate in clay-rich sediment, with moderate resistivity (between 2-10 Ωm) increases above background resistivity in zones that exceed 60 m thick. Additionally, the electromagnetic resistivity curves in these wells separate suggesting that the gas hydrate occurs in high-angle fractures. We will present our seismic dataset, our continuing analysis and selected drill sites in the Orca and Choctaw basins. Furthermore, our analysis in the southeastern section of the study area underscores the importance of interpreting faults when considering phase reversals in hydrate systems.

Age and morphodynamics of a sandy beach fronted by a macrotidal mud flat along the west coast of Korea: a lateral headland bypass model for beach-dune formation

NASA Astrophysics Data System (ADS)

Chang, Tae Soo; Hong, Seok Hwi; Chun, Seung Soo; Choi, Jeong-Heon

2017-08-01

The Dasari beach-dune system fronted by an intertidal mud flat is a typical example of numerous small beaches found both in embayments and along the open macrotidal west coast of Korea. The beach is frequently exposed to energetic wave action at high tide in winter. Although this coastal dune-sandy beach-intertidal mud flat system has previously been described, its origin and morphodynamic behavior has to date not been firmly established. To clarify these issues, elevation profiles and surficial sediment samples were collected seasonally along five monitoring transects across the tidal flat. In addition, box-cores as well as vibro- and drill-cores were acquired along the middle transect. Optically stimulated luminescence (OSL) and 14C- AMS (accelerator mass spectrometry) dating methods were applied to determine the age of the tidal flat, the beach and the dune deposits. The results show that Dasari beach is topographically composed of two distinct morphological and sedimentological sectors, comprising a high-tide sandy beach that merges seaward into an extensive low-tide tidal flat composed of mud. The transition between the two sectors is marked by a sharp break in slope and change in internal sedimentary structures. At the boundary, the subtle shoreward fining trend in mean grain size on the intertidal flat switches to a pronounced shoreward coarsening trend. Near the transition, mixing between the beach sand and the mud is observed. Another striking feature is a seasonal rotation of the beach system centered on the middle sector, with the northern sector eroding in winter and accreting in summer, and the southern sector accreting in winter and eroding in summer. The spatial grain-size pattern reveals that the beach is fed from the neighboring beach in the north by lateral headland bypassing, rather than onshore transport across the tidal flat, the intermittent lateral supply of sand explaining the seasonal rotation of the beach. Stratigraphically, the beach-dune deposits are underlain by muddy tidal flat deposits, which results in a clear upward coarsening grain-size trend and thus intimates transgressive deposition associated with sea-level rise over the past 7-8 ka. However, a time gap of 4-5 thousand years between the tidal flat and the beach-dune deposits indicates that there is no genetic link between the two depositional systems. As the modern beach-dune system is remote from the former landward limit of the tidal flat, a continuous retreat model must be rejected. Instead, a lateral headland bypassing model, in which sand supplied alongshore progressively encroached the tidal flat, is more plausible. In the light of this interpretation, many of the barrier beach-lagoon models proposed for the macrotidal west coast of Korea need to be reconsidered.

Effect of formulation variables on the physical properties and stability of Dead Sea mud masks.

PubMed

Shahin, Sawsan; Hamed, Saja; Alkhatib, Hatim S

2015-01-01

The physical stability of Dead Sea mud mask formulations under different conditions and their rheological properties were evaluated as a function of the type and level of thickeners, level of the humectant, incorporation of ethanol, and mode of mud treatment. Formulations were evaluated in terms of visual appearance, pH, moisture content, spreadability, extrudability, separation, rate of drying at 32 degrees C, and rheological properties. Prepared mud formulations and over-the-shelf products showed viscoplastic shear thinning behavior; satisfactory rheological behavior was observed with formulations containing a total concentration of thickeners less than 10% (w/w). Casson and Herschel-Bulkley models were found the most suitable to describe the rheological data of the prepared formulations. Thickener incorporation decreased phase separation and improved formulation stability. Bentonite incorporation in the mud prevented color changes during stability studies while glycerin improved spreadability. Addition of 5% (w/w) ethanol improved mud extrudability, slightly increased percent separation, accelerated drying at 32 degrees C, and decreased viscosity and yield stress values. Different mud treatment techniques did not cause a clear behavioral change in the final mud preparation. B10G and K5B5G were labeled as "best formulas" based on having satisfactory physical and aesthetic criteria investigated in this study, while other formulations failed in one or more of the tests we have performed.

Anatomy Of The ‘LuSi’ Mud Eruption, East Java

NASA Astrophysics Data System (ADS)

Tingay, M. R.

2009-12-01

Early in the morning of the 29th of May 2006, hot mud started erupting from the ground in the densely populated Porong District of Sidoarjo, East Java. With initial flow rates of ~5000 cubic meters per day, the mud quickly inundated neighbouring villages. Over two years later and the ‘Lusi’ eruption has increased in strength, expelling over 90 million cubic meters of mud at an average rate of approximately 100000 cubic meters per day. The mud flow has now covered over 700 hectares of land to depths of over 25 meters, engulfing a dozen villages and displacing approximately 40000 people. In addition to the inundated areas, other areas are also at risk from subsidence and distant eruptions of gas. However, efforts to stem the mud flow or monitor its evolution are hampered by our overall lack of knowledge and consensus on the subsurface anatomy of the Lusi mud volcanic system. In particular, the largest and most significant uncertainties are the source of the erupted water (shales versus deep carbonates), the fluid flow pathways (purely fractures versus mixed fracture and wellbore) and disputes over the subsurface geology (nature of deep carbonates, lithology of rocks between shale and carbonates). This study will present and overview of the anatomy of the Lusi mud volcanic system with particular emphasis on these critical uncertainties and their influence on the likely evolution of disaster.

Microbial stability of worm castings and sugarcane filter mud compost blended with biochar

USDA-ARS?s Scientific Manuscript database

Organic amendments such as worm castings and filter mud compost can provide nutrient rich substrates for enhanced plant growth. Physico-chemical and microbial stability of these substrates might be enhanced with the addition of biochar. A series of experiments was carried out to determine the stab...

Red mud addition in the raw meal for the production of Portland cement clinker.

PubMed

Tsakiridis, P E; Agatzini-Leonardou, S; Oustadakis, P

2004-12-10

The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste, which is obtained from bauxite during the Bayer process for alumina production, in the raw meal for the production of Portland cement clinker. For that reason, two samples of raw meals were prepared: one with ordinary raw materials, as a reference sample ((PC)Ref), and another with 3.5% red mud ((PC)R/M). The effect on the reactivity of the raw mix was evaluated on the basis of the unreacted lime content in samples sintered at 1350, 1400 and 1450 degrees C. Subsequently, the clinkers were produced by sintering the two raw meals at 1450 degrees C. The results of chemical and mineralogical analyses as well as the microscopic examination showed that the use of the red mud did not affect the mineralogical characteristics of the so produced Portland cement clinker. Furthermore, both clinkers were tested by determining the grindability, setting time, compressive strength and expansibility. The hydration products were examined by XRD analysis at 2, 7, 28 and 90 days. The results of the physico-mechanical tests showed that the addition of the red mud did not negatively affect the quality of the produced cement.

Temporary Cementitious Sealers in Enhanced Geothermal Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sugama T.; Pyatina, T.; Butcher, T.

2011-12-31

Unlike conventional hydrothennal geothermal technology that utilizes hot water as the energy conversion resources tapped from natural hydrothermal reservoir located at {approx}10 km below the ground surface, Enhanced Geothermal System (EGS) must create a hydrothermal reservoir in a hot rock stratum at temperatures {ge}200 C, present in {approx}5 km deep underground by employing hydraulic fracturing. This is the process of initiating and propagating a fracture as well as opening pre-existing fractures in a rock layer. In this operation, a considerable attention is paid to the pre-existing fractures and pressure-generated ones made in the underground foundation during drilling and logging. Thesemore » fractures in terms of lost circulation zones often cause the wastage of a substantial amount of the circulated water-based drilling fluid or mud. Thus, such lost circulation zones must be plugged by sealing materials, so that the drilling operation can resume and continue. Next, one important consideration is the fact that the sealers must be disintegrated by highly pressured water to reopen the plugged fractures and to promote the propagation of reopened fractures. In response to this need, the objective of this phase I project in FYs 2009-2011 was to develop temporary cementitious fracture sealing materials possessing self-degradable properties generating when {ge} 200 C-heated scalers came in contact with water. At BNL, we formulated two types of non-Portland cementitious systems using inexpensive industrial by-products with pozzolanic properties, such as granulated blast-furnace slag from the steel industries, and fly ashes from coal-combustion power plants. These byproducts were activated by sodium silicate to initiate their pozzolanic reactions, and to create a cemetitious structure. One developed system was sodium silicate alkali-activated slag/Class C fly ash (AASC); the other was sodium silicate alkali-activated slag/Class F fly ash (AASF) as the binder of temper-try sealers. Two specific additives without sodium silicate as alkaline additive were developed in this project: One additive was the sodium carboxymethyl cellulose (CMC) as self-degradation promoting additive; the other was the hard-burned magnesium oxide (MgO) made from calcinating at 1,000-1,500 C as an expansive additive. The AASC and AASF cementitious sealers made by incorporating an appropriate amount of these additives met the following six criteria: 1) One dry mix component product; 2) plastic viscosity, 20 to 70 cp at 300 rpm; 3) maintenance of pumpability for at least 1 hour at 85 C; 4) compressive strength >2000 psi; 5) self-degradable by injection with water at a certain pressure; and 6) expandable and swelling properties; {ge}0.5% of total volume of the sealer.« less

Determination of effects of turbulence flow in a cathode environment on electricity generation using a tidal mud-based cylindrical-type sediment microbial fuel cell.

PubMed

An, Junyeong; Lee, Soo-Jin; Ng, How Yong; Chang, In Seop

2010-12-01

We examined the possibility of harvesting electricity from the surface of a tidal mud flat using a cylindrical-type sediment microbial fuel cell (SMFC), a marine mud battery (MMB), which can be applied in a sea environment where the ebb and flow occur due to tidal difference. In addition, we indirectly investigated the influence of ebb and flow in a lab, using aeration, argon gassing, and by agitating the cathodic solution. The MMBs consisted of cylindrical acrylic compartments containing a nylon membrane, an anode, and a cathode in a single body. The MMBs were stuck vertically into an artificial tidal mud flat such that the anode electrode was in direct contact with the tidal mud surface. As a result, the maximum current and power density generated were 35 mA/m(2) and 9 mW/m(2), respectively, thus verifying that it is possible to harvest electricity from the surface of a tidal mud flat using an MMB without burying the anode electrode in the tidal mud. Furthermore, the results of tests using an artificial turbulence flow showed the flow induced by the tidal ebb and flow could allow the performance of MMBs to be enhanced. Copyright © 2010 Elsevier Ltd. All rights reserved.

Drilling into the deep interior of the Nankai accretionary prism: Preliminary results of IODP NanTroSEIZE Expedition 348

NASA Astrophysics Data System (ADS)

Tobin, H. J.; Hirose, T.; Saffer, D. M.; Toczko, S.; Maeda, L.

2014-12-01

International Ocean Discovery Program (IODP) Expedition 348, the latest advance of the NanTroSEIZE project, started on 13 September 2013 and was completed on 29 January 2014. During Expedition 348, the drilling vessel Chikyu advanced the ultra-deep riser hole at Site C0002, located 80 km offshore of the Kii Peninsula, from a depth of 860 meters below sea floor (mbsf) to 3058.5 mbsf, the world record for the deepest scientific ocean drilling, and cased it for future deepening. The drilling operation successfully obtained data on formation physical properties from logging while drilling (LWD) tools, as well as from lithological analyses of cuttings and core from the interior of the active accretionary prism at the Nankai Trough. IODP Site C0002 is the currently only borehole to access the deep interior of an active convergent margin. Preliminary scientific results of Expedition 348 are as follows: (1) Fine-grained turbiditic mudstones with coarser silty and sandy interbeds, exhibiting steep dips (between ~60 and 90 degrees) are predominant in the prism down to ~3000 mbsf. The biostratigraphic age of the sediments in the lowermost part of the hole is thought to be 9-11 Ma, with an assumed age of accretion of 3-5 Ma. (2) Slickenlined surfaces, deformation bands and mineral veins are present throughout the drilled interval, while well-developed scaly clay fabrics are increasingly observed below ~2200 mbsf. A substantial fault zone with well-developed foliation was successfully cored from the deep interior of the prism at ~2205 mbsf. (3) Porosity generally decreases from ~60% to ~20% from the seafloor to 3000 mbsf. However, physical properties including grain density, electrical conductivity and P-wave velocity suggest fairly homogeneous properties in the interior of the prism between ~2000 and 3000 mbsf. (4) Mud gas analysis during the riser drilling indicates that a source of methane gas shifts from microbial origin to thermogenic at around 2325 mbsf. (5) The maximum horizontal principal stress at ~2200 mbsf is in the NE-SW direction. The inner wedge at ~ 2000 mbsf is currently in a strike-slip stress regime.

Relevance of East African Drill Cores to Human Evolution: the Case of the Olorgesailie Drilling Project

NASA Astrophysics Data System (ADS)

Potts, R.

2016-12-01

Drill cores reaching the local basement of the East African Rift were obtained in 2012 south of the Olorgesailie Basin, Kenya, 20 km from excavations that document key benchmarks in the origin of Homo sapiens. Sediments totaling 216 m were obtained from two drilling locations representing the past 1 million years. The cores were acquired to build a detailed environmental record spatially associated with the transition from Acheulean to Middle Stone Age technology and extensive turnover in mammalian species. The project seeks precise tests of how climate dynamics and tectonic events were linked with these transitions. Core lithology (A.K. Behrensmeyer), geochronology (A. Deino), diatoms (R.B. Owen), phytoliths (R. Kinyanjui), geochemistry (N. Rabideaux, D. Deocampo), among other indicators, show evidence of strong environmental variability in agreement with predicted high-eccentricity modulation of climate during the evolutionary transitions. Increase in hominin mobility, elaboration of symbolic behavior, and concurrent turnover in mammalian species indicating heightened adaptability to unpredictable ecosystems, point to a direct link between the evolutionary transitions and the landscape dynamics reflected in the Olorgesailie drill cores. For paleoanthropologists and Earth scientists, any link between evolutionary transitions and environmental dynamics requires robust evolutionary datasets pertinent to how selection, extinction, population divergence, and other evolutionary processes were impacted by the dynamics uncovered in drill core studies. Fossil and archeological data offer a rich source of data and of robust environment-evolution explanations that must be integrated into efforts by Earth scientists who seek to examine high-resolution climate records of human evolution. Paleoanthropological examples will illustrate the opportunities that exist for connecting evolutionary benchmarks to the data obtained from drilled African muds. Project members: R. Potts, A.K. Behrensmeyer, E. Beverly, K. Brady, J. Bright, E. Brown, J. Clark, A. Cohen, A. Deino, P. deMenocal, D. Deocampo, R. Dommain, J.T. Faith, J. King, R. Kinyanjui, N. Levin, J. Moerman, V. Muiruri, A. Noren, R.B. Owen, N. Rabideaux, R. Renaut, S. Rucina, J. Russell, J. Scott, M. Stockhecke, K. Uno

IODP Expedition 338: NanTroSEIZE Stage 3: NanTroSEIZE plate boundary deep riser 2

NASA Astrophysics Data System (ADS)

Moore, G. F.; Kanagawa, K.; Strasser, M.; Dugan, B.; Maeda, L.; Toczko, S.

2014-01-01

The Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) is designed to investigate fault mechanics and seismogenesis along a subduction megathrust, with objectives that include characterizing fault slip, strain accumulation, fault and wall rock composition, fault architecture, and state variables throughout an active plate boundary system. Integrated Ocean Drilling Program (IODP) Expedition 338 was planned to extend and case riser Hole C0002F from 856 to 3600 meters below the seafloor (m b.s.f.). Riser operations extended the hole to 2005.5 m b.s.f., collecting logging-while-drilling (LWD) and measurement-while-drilling, mud gas, and cuttings data. Results reveal two lithologic units within the inner wedge of the accretionary prism that are separated by a prominent fault zone at ~ 1640 m b.s.f. Due to damage to the riser during unfavorable winds and strong currents, riser operations were suspended, and Hole C0002F left for re-entry during future riser drilling operations. Contingency riserless operations included coring at the forearc basin site (C0002) and at two slope basin sites (C0021 and C0022), and LWD at one input site (C0012) and at three slope basin sites (C0018, C0021 and C0022). Cores and logs from these sites comprehensively characterize the alteration stage of the oceanic basement input to the subduction zone, the early stage of Kumano Basin evolution, gas hydrates in the forearc basin, and recent activity of the shallow megasplay fault zone system and associated submarine landslides.

Potential sulfate reduction in deeply buried coalbeds 2 km below the seafloor off the Shimokita Peninsula (Japan)

NASA Astrophysics Data System (ADS)

Glombitza, C.; Inagaki, F.; Lever, M. A.; Jørgensen, B. B.

2013-12-01

Integrated Ocean Drilling Program (IODP) Expedition 337 aboard the drilling vessel Chikyu in summer 2012 was the first IODP expedition to drill into a deeply buried hydrocarbon system by riser drilling and, in the process, extended the depth record of scientific ocean drilling to 2466 meters below seafloor (mbsf). A main scientific goal of Expedition 337 was to explore microbial communities associated with deeply buried coalbeds 2 km below the seafloor at Site C0020 off the Shimokita Peninsula of Japan, northwestern coast of the Pacific Ocean. Four lithological units were defined according to sedimentological observations (Inagaki et al. 2012). Temperature measurements during wireline logging revealed in-situ temperatures in the range habitable for life, with ~40-45°C in 2km-deep coalbeds and 60°C at the bottom of the hole. To determine potential sulfate reduction rates (pSRRs) throughout the lower half of the borehole (1200-2466 mbsf; Units II - IV), we prepared slurries from fresh core material in artificial seawater medium containing 1 mM of sulfate and incubated these onboard with 35S-labeled sulfate at approximate in-situ temperatures (i.e., 25, 35, and 45°C). A duplicate set of incubations was started from each sample, one with only N2 in the headspace, and one with N2 + CH4 in the headspace. We incubated samples with 3.7 MBq 35S for a period of 10 days to achieve a detection limit of ca. 10 fmol sulfate cm-3 d-1. pSRRs were close to the detection limit in Unit II and increased by two orders of magnitude up to 2 pmol cm-3 d-1 in the coal-bearing strata (Unit III), decreasing again below in Unit IV. Maximum rates in Unit III reached values similar to those determined during the Chikyu shakedown cruise at 350 mbsf at the same site in 2006. In contrast to the pSRRs determined previously, however, addition of methane did not stimulate pSRRs, suggesting that potential sulfate reduction was supported by electron donors other than methane. The increase of pSRR in the coal-bearing unit is in accordance with other indicators of increased microbial activity in this depth interval, such as high C1/C2 ratios with low 13C/12C isotope ratios of methane observed by real-time mud gas logging during riser drilling. Inagaki, F., K.-U. Hinrichs, Y. Kubo, and the Expedition 337 Scientists (2012), Deep coalbed biosphere off Shimokita: microbial processes and hydrocarbon system associated with deeply buried coalbed in the ocean, IODP Prel. Rept., 337, doi: 10.2204/iodp.pr.337.2012

Cenozoic sedimentation in the Mumbai Offshore Basin: Implications for tectonic evolution of the western continental margin of India

NASA Astrophysics Data System (ADS)

Nair, Nisha; Pandey, Dhananjai K.

2018-02-01

Interpretation of multichannel seismic reflection data along the Mumbai Offshore Basin (MOB) revealed the tectonic processes that led to the development of sedimentary basins during Cenozoic evolution. Structural interpretation along three selected MCS profiles from MOB revealed seven major sedimentary sequences (∼3.0 s TWT, thick) and the associated complex fault patterns. These stratigraphic sequences are interpreted to host detritus of syn- to post rift events during rift-drift process. The acoustic basement appeared to be faulted with interspaced intrusive bodies. The sections also depicted the presence of slumping of sediments, subsidence, marginal basins, rollover anticlines, mud diapirs etc accompanied by normal to thrust faults related to recent tectonics. Presence of upthrusts in the slope region marks the locations of local compression during collision. Forward gravity modeling constrained with results from seismic and drill results, revealed that the crustal structure beneath the MOB has undergone an extensional type tectonics intruded with intrusive bodies. Results from the seismo-gravity modeling in association with litholog data from drilled wells from the western continental margin of India (WCMI) are presented here.

Characterization of MUDENG, a novel anti-apoptotic protein

PubMed Central

Choi, J-H; Lim, J-B; Wickramanayake, D D; Wagley, Y; Kim, J; Lee, H-C; Seo, H G; Kim, T-H; Oh, J-W

2016-01-01

MUDENG (Mu-2-related death-inducing gene, MuD) is revealed to be involved in cell death signaling. Astrocytes, the major glial cell type in the central nervous system, are a source of brain tumors. In this study, we examined MuD expression and function in human astroglioma cells. Stimulation of U251-MG cells with tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) resulted in a 40% decrease in cell viability and a 33% decrease in MuD protein levels, although not in MuD mRNA levels. To study the functional relevance of MuD expression, stable transfectants expressing high levels of MuD were generated. Stimulation of these transfectants with TRAIL resulted in enhanced cell survival (77% for stable and 46% for control transfectants). Depletion of MuD led to a marked reduction upon TRAIL stimulation in cell viability (22% in MuD-depleted cells and 54% in control cells). In addition, we observed that MuD depletion increased the susceptibility of the cells to TRAIL by enhancing the cleavage of caspase-3/-9 and BH3-interacting domain death agonist (Bid). A unique 25-kDa fragment of B-cell lymphoma 2 (Bcl-2) lacking BH4 was observed 60–180 min post TRAIL treatment in MuD-depleted cells, suggesting that Bcl-2 is converted from its anti-apoptotic form to the truncated pro-apoptotic form. Importantly, the TRAIL-mediated decrease in cell viability in MuD-depleted cells was abrogated upon Bid depletion, indicating that the role of MuD in apoptotic signaling takes place at the Bid and Bcl-2 junction. MuD localizes predominantly in the endoplasmic reticulum and partly in the mitochondria and its amounts are reduced 6 h post TRAIL stimulation, presumably via caspase-3-mediated MuD cleavage. Collectively, these results suggest that MuD, a novel signaling protein, not only possesses an anti-apoptotic function but may also constitute an important target for the design of ideal candidates for combinatorial treatment strategies for glioma cells. PMID:27136675

New access to the deep interior of the Nankai accretionary complex and comprehensive characterization of subduction inputs and recent mega splay fault activity (IODP-NanTroSEIZE Expedition 338)

NASA Astrophysics Data System (ADS)

Strasser, Michael; Moore, Gregory F.; Kanagawa, Kyuichi; Dugan, Brandon; Fabbri, Olivier; Toczko, Sean; Maeda, Lena

2013-04-01

The Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) is a coordinated, multi-expedition Integrated Ocean Drilling Program (IODP) drilling project designed to investigate fault mechanics and seismogenesis along subduction megathrusts through direct sampling, in situ measurements, and long-term monitoring in conjunction with allied laboratory and numerical modeling studies. IODP Expedition 338 (1 October 2012 - 13 January 2013), extended riser Hole C0002F from 856 meters below the sea floor (mbsf) to 2005 mbsf. Site C0002 is the centerpiece of the NanTroSEIZE project, and is planned to be deepened to eventually reach the seismogenic fault zone during upcoming drilling expeditions. The original Exp. 338 operational plan to case the hole to 3600 mbsf had to be revised as sudden changes in sea conditions resulted in damage to parts of the riser system, thus the hole was suspended at 2005 mbsf but left for future re-entry. The revised operation plan included additional riserless logging and coring of key targets not sampled during previous NanTroSEIZE expeditions, but relevant to comprehensively characterize the alteration stage of the oceanic basement input to the subduction zone, the early stage of Kumano Basin evolution and the recent activity of the shallow mega splay fault zone system and submarine landslides. Here we present preliminary results from IODP Exp. 338: Logging While Drilling (LWD), mud gas monitoring and analysis on cuttings from the deep riser hole characterize two lithological units within the internal accretionary prism, separated by a prominent fault zone at ~1640 mbsf. Internal style of deformation, downhole increase of thermogenically formed formation gas and evidence for mechanical compaction and cementation document a complex structural evolution and provide unprecedented insights into the mechanical state and behavior of the wedge at depth. Additionally, multiple samples of the unconformity between the Kumano Basin and accretionary prism at Site C0002 shed new light on this debatable unconformity boundary and suggest variable erosional processes active on small spatial scales. Results from riserless drilling at input Site C0012 include 178.7 m of detailed LWD characterization of the oceanic basement, indicating an upper ~100 m zone of altered pillow basalts and sheet flow deposits, and a lower, presumably less altered basement unit without indication for interlayered sediment horizons. Low angle faults identified in X-ray Computed Tomography images and structural investigation on cores from Site C0022, located in the slope basin immediately seaward of the megasplay fault zone, indicate splay-fault-related, out-of-sequence thrusting within slope basin sediments and shed new light on recent activity of the megasplay. Lastly, Exp. 338 added additional coring to improve our understanding of submarine landslides in the slope basins seaward of the splay fault and yields new LWD data to characterize in situ internal structures and properties of mass-transport deposits as it relates to the dynamics and kinematics of submarine landslides.

A comparison/validation of a fractional derivative model with an empirical model of non-linear shock waves in swelling shales

NASA Astrophysics Data System (ADS)

Droghei, Riccardo; Salusti, Ettore

2013-04-01

Control of drilling parameters, as fluid pressure, mud weight, salt concentration is essential to avoid instabilities when drilling through shale sections. To investigate shale deformation, fundamental for deep oil drilling and hydraulic fracturing for gas extraction ("fracking"), a non-linear model of mechanic and chemo-poroelastic interactions among fluid, solute and the solid matrix is here discussed. The two equations of this model describe the isothermal evolution of fluid pressure and solute density in a fluid saturated porous rock. Their solutions are quick non-linear Burger's solitary waves, potentially destructive for deep operations. In such analysis the effect of diffusion, that can play a particular role in fracking, is investigated. Then, following Civan (1998), both diffusive and shock waves are applied to fine particles filtration due to such quick transients , their effect on the adjacent rocks and the resulting time-delayed evolution. Notice how time delays in simple porous media dynamics have recently been analyzed using a fractional derivative approach. To make a tentative comparison of these two deeply different methods,in our model we insert fractional time derivatives, i.e. a kind of time-average of the fluid-rocks interactions. Then the delaying effects of fine particles filtration is compared with fractional model time delays. All this can be seen as an empirical check of these fractional models.

Discovery of siderite in marine sediment: Source and effect of violent gas venting at the Tsanyao Mud Volcano, offshore SW Taiwan

NASA Astrophysics Data System (ADS)

Tseng, Y.; Lin, S.; Hsieh, I. C.; Lien, K. L.

2016-12-01

Tsanyao mud volcano is a 400 meters high, 5 kilometers in diameter, a center crater of 50 meters width activing venting mud diapir. The gigantic size of mud volcano indicate massive transportation of material, i.e., gas, fluid, and breccia from deep to the sea floor in building up the mud volcano. The mud volcano is located at the upper slope of the accretionary wedge with a surrounding water depth of about xx m, offshore Southwestern Taiwan. On shore, a series of active mud volcanos also exist in a trend similar to those found offshore. In order to understand sources of gas, fluid, solid materials and the effect of gas migration and associate authigenic mineral formation, we have obtained multibeam bathymetry, water column echo sounding, together with sediment XRD and SEM and pore water composition of methane, sulfide, sulfate, chloride, potassium, lithium, boron, and water O-18 at the study mud volcano. We have observed more than 30 flares around the main cone within a perimeter of 10 square miles. δ13C values of methane in the pore water ranged from -30 to -50 ‰. The lower C13 ratios, together with high C2+/C1 ratios demonstrated that vent gas is mostly thermogenic in origin. Higher thermal gradient and water temperature indicated that cone top is unfavorable for gas-hydrate formation, however, gas hydrate may exist at a deeper part of the mud volcano system. High concentration of sulfide presence right near the sulfate-methane interface, a result of anoxic methane oxidation. However, low concentrations of pyrite in sediments indicated that AOM did not favor pyrite formation at depth. In addition, abundant siderite were found in the sediments collected in the mud volcano cone. Rapid consumption of sulfate through AOM reaction generated a condition favor the siderite fomation, instead of the typical pyrite formation commonly observed.

Preparation and Characterization of Plasma Electrolytic Oxidation Coating on 5005 Aluminum Alloy with Red Mud as an Electrolyte Additive

NASA Astrophysics Data System (ADS)

Liu, Shifeng; Zeng, Jianmin; Wang, Youbin

2017-10-01

A coating with red mud as an electrolyte additive was applied to 5005 aluminum alloy using plasma electrolytic oxidation (PEO). The phase composition of the coating was investigated using X-ray diffraction. Scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS) was used to determine the microstructure and composition profiles of the coating. The coating/substrate adhesion was determined by scratch testing. The corrosion behaviors of the substrate and coating were evaluated using potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS). The results indicated that the PEO coating with red mud consisted mainly of α-Al2O3 and γ-Al2O3, with small amounts of Fe2O3, CaCO3, and CaTiO3. The surface of the coating was the color of the red mud. The coating had a uniform thickness of about 80 μm and consisted of two main layers: a 6- μm porous outer layer and a 74- μm dense inner layer, which showed typical metallurgical adhesion (coating/substrate adhesion strength of 59 N). The coating hardness was about 1142 HV, much higher than that of the substrate (60 HV). The corrosion potential E corr and corrosion current density i corr of the coating were estimated to be -0.743 V and 3.85 × 10-6 A cm-2 from the PDP curve in 3.5 wt pct NaCl solution, and the maximum impedance and phase angle of the coating were 11 000 Ω and -67 deg, respectively, based on EIS. PEO coating with red mud improved the surface properties and corrosion resistance of 5005 aluminum alloy. This study also shows a potential method for reusing red mud.

The potential application of red mud and soil mixture as additive to the surface layer of a landfill cover system.

PubMed

Ujaczki, Éva; Feigl, Viktória; Molnár, Mónika; Vaszita, Emese; Uzinger, Nikolett; Erdélyi, Attila; Gruiz, Katalin

2016-06-01

Red mud, the by-product of aluminum production, has been regarded as a problematic residue all over the world. Its storage involves risks as evidenced by the Ajka red mud spill, an accident in Hungary where the slurry broke free, flooding the surrounding areas. As an immediate remediation measure more than 5cm thick red mud layer was removed from the flooded soil surface. The removed red mud and soil mixture (RMSM) was transferred into the reservoirs for storage. In this paper the application of RMSM is evaluated in a field study aiming at re-utilizing waste, decreasing cost of waste disposal and providing a value-added product. The purpose was to investigate the applicability of RMSM as surface layer component of landfill cover systems. The field study was carried out in two steps: in lysimeters and in field plots. The RMSM was mixed at ratios ranging between 0 and 50% w/w with low quality subsoil (LQS) originally used as surface layer of an interim landfill cover. The characteristics of the LQS+RMSM mixtures compared to the subsoil (LQS) and the RMSM were determined by physical-chemical, biological and ecotoxicological methods. The addition of RMSM to the subsoil (LQS) at up to 20% did not result any ecotoxic effect, but it increased the water holding capacity. In addition, the microbial substrate utilization became about triple of subsoil (LQS) after 10months. According to our results the RMSM mixed into subsoil (LQS) at 20% w/w dose may be applied as surface layer of landfill cover systems. Copyright © 2016. Published by Elsevier B.V.

A Novel Well Drill Assisted with High-Frequency Vibration Using the Bending Mode

PubMed Central

Qi, Xinda; Chen, Weishan; Tang, Xintian; Shi, Shengjun

2018-01-01

It is important for companies to increase the efficiency of drilling as well as prolong the lifetime of the drilling tool. Since some previous investigations indicated that a superposition of well drilling with an additional vibration increases the drilling efficiency, this paper introduces a novel well drill which is assisted with additional vibrations by means of piezoelectric sandwich bending vibration transducer. The proposed drill uses bending vibrations in two different directions to from an elliptical trajectory movement, which can help the drill to break the surface of hard material more efficiently and clean away the lithic fragments more easily. The proposed well drill with bending vibration transducer is designed to have a resonance frequency of the first bending vibration mode of about 1779 Hz. The motion equation of the particle on the edge of the drill bit is developed and analyzed. The vibration trajectory of the particle on the edge of the drill bit is calculated by using finite element method. A prototype of the proposed drill using bending vibrations is fabricated and tested to verify the aim of drilling efficiency increase. The feed speed of the vibration assisted drilling is tested to be about 0.296 mm/s when the excitation voltage of the transducer is 300 V, while this speed decreases to about 0.195 mm/s when no vibration is added. This comparison shows that the feed speed of the vibration assisted drilling is about 52% higher than that of the normal drilling, which means the proposed drill has a better efficiency and it is important to consider vibration superimposition in well drilling. In addition, the surface of the drill hole gained by the vibration assisted drilling is smoother than that of the normal drilling, which makes the clearance easier. PMID:29641481

Preliminary report on geophysical well-logging activity on the Salton Sea Scientific Drilling Project, Imperial Valley, California

USGS Publications Warehouse

Paillet, Frederick L.; Morin, R.H.; Hodges, H.E.

1986-01-01

The Salton Sea Scientific Drilling Project has culminated in a 10,564-ft deep test well, State 2-14 well, in the Imperial Valley of southern California. A comprehensive scientific program of drilling, coring, and downhole measurements, which was conducted for about 5 months, has obtained much scientific information concerning the physical and chemical processes associated with an active hydrothermal system. This report primarily focuses on the geophysical logging activities at the State 2-14 well and provides early dissemination of geophysical data to other investigators working on complementary studies. Geophysical-log data were obtained by a commercial logging company and by the U.S. Geological Survey (USGS). Most of the commercial logs were obtained during three visits to the site; only one commercial log was obtained below a depth of 6,000 ft. The commercial logs obtained were dual induction, natural gamma, compensated neutron formation density, caliper and sonic. The USGS logging effort consisted of four primary periods, with many logs extending below a depth of 6,000 ft. The USGS logs obtained were temperature, caliper, natural gamma, gamma spectral, epithermal neutron, acoustic velocity, full-waveform, and acoustic televiewer. Various problems occurred throughout the drilling phase of the Salton Sea Scientific Drilling Project that made successful logging difficult: (1) borehole constrictions, possibly resulting from mud coagulation, (2) maximum temperatures of about 300 C, and (3) borehole conditions unfavorable for logging because of numerous zones of fluid loss, cement plugs, and damage caused by repeated trips in and out of the hole. These factors hampered and compromised logging quality at several open-hole intervals. The quality of the logs was dependent on the degree of probe sophistication and sensitivity to borehole-wall conditions. Digitized logs presented were processed on site and are presented in increments of 1,000 ft. A summary of the numerous factors that may be relevant to this interpretation also is presented. (Lantz-PTT)

Effects of drill cuttings on larvae of the cold-water coral Lophelia pertusa

NASA Astrophysics Data System (ADS)

Järnegren, Johanna; Brooke, Sandra; Jensen, Henrik

2017-03-01

Fossil fuel consumption is predicted to dominate energy needs until at least 2040. To make up for reduced production from maturing fields, oil and gas exploration activities on the Norwegian continental shelf have greatly increased over the past several years. Strict emission controls have resulted in a substantial reduction in the release of hazardous chemicals. However, because of the increased exploration the discharges of water-based drill cuttings and muds have increased substantially, temporarily increasing water column sediment loads. The stony coral Lophelia pertusa is the most widely distributed and well-studied of the structure forming cold water corals (CWC) and it thrives in Norwegian waters where many reefs are located in the vicinity of oil platforms or exploration areas. This species provides habitat for a diverse and abundant assemblage of invertebrates and fishes, including commercially valuable species. High sediment loads are known to negatively affect adult corals, but impacts on the early life history stages are unknown. We investigated the effects of a range of drill cutting concentrations (0.5-640 ppm) on larvae of L. pertusa at ages five days and 15-20 days. One set of experiments was conducted in static experimental chambers that exposed larvae to decreasing concentrations over time, and the other maintained continuous drill cutting concentrations for the duration of the experiment (24 h). Increased sediment load for a duration of 24 h caused significant larval mortality, but there was an age-dependent difference in sensitivity of larvae. Younger larvae were significantly more susceptible to lower concentrations of drill cuttings than older larvae, while the older larvae were significantly more affected at higher concentrations. Five day old larvae were affected at treatment concentration 40 ppm. The larval cilia became clogged, preventing the larvae from swimming actively and ultimately causing mortality. Larvae of many species use cilia for swimming and feeding, so negative impacts of increased sediment may not be limited to corals.

Reservoir development in bryozoan bafflestone facies of the Ullin (Warsaw) Limestone (Middle Mississippian) in the Illinois basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lasemi, Z.; Treworgy, J.D.; Norby, R.D.

1994-08-01

Recent drilling in Enfield South and Johnsonville fields in southern Illinois has encountered prolific petroleum-producing zones within the Ullin (Warsaw) Limestone. This and large cumulative production from a number of older wells in the Illinois basin indicate that the Ullin has greater reservoir potential than previously recognized. The Ullin reservoir facies is mainly a fenestrate bryozoan-dominated bafflestone developed on the flanks of Waulsortian-type mud mounds or on transported skeletal sand buildups. Subsurface geology and petrography reveal such porous bryozoan bafflestone facies (some with shows of oil) at various horizons within the Ullin. However, in part because of water problems inmore » some areas, only the upper part of the Ullin has been tested thus far and, as a result, significant reservoirs in the deeper part of the unit may have been missed. Preliminary data indicate several facies in the Ullin that vary in their aerial distribution in the basin. These facies include (1) skeletal sand-wave facies and/or bryozoan bafflestone in the upper Ullin, (2) bryozoan bafflestone with a dense Waulsortian mud mound core, (3) thick bryozoan bafflestone over a skeletal grainstone facies, and (4) thick mud mound-dominated facies with thin porous flanking bafflestone/grainstone facies. Areas with facies type 1 and 2 have the highest potential for commercial reservoir development. Facies type 3, although quite porous, is commonly wet, and the porous facies type 4 may be localized and not extensive enough to be commercial. Petrographic examination shows excellent preservation of primary intra- and interparticle porosities within the bryozoan bafflestone facies. The generally stable original mineralogy prevented extensive dissolution-reprecipitation and occlusion of porosity. Further, the stable mineralogy and minor early marine cementation prevented later compaction and burial diagenesis.« less

In Situ Temperature Measurements at the Svalbard Continental Margin: Implications for Gas Hydrate Dynamics

NASA Astrophysics Data System (ADS)

Riedel, M.; Wallmann, K.; Berndt, C.; Pape, T.; Freudenthal, T.; Bergenthal, M.; Bünz, S.; Bohrmann, G.

2018-04-01

During expedition MARIA S. MERIAN MSM57/2 to the Svalbard margin offshore Prins Karls Forland, the seafloor drill rig MARUM-MeBo70 was used to assess the landward termination of the gas hydrate system in water depths between 340 and 446 m. The study region shows abundant seafloor gas vents, clustered at a water depth of ˜400 m. The sedimentary environment within the upper 100 m below seafloor (mbsf) is dominated by ice-berg scours and glacial unconformities. Sediments cored included glacial diamictons and sheet-sands interbedded with mud. Seismic data show a bottom simulating reflector terminating ˜30 km seaward in ˜760 m water depth before it reaches the theoretical limit of the gas hydrate stability zone (GHSZ) at the drilling transect. We present results of the first in situ temperature measurements conducted with MeBo70 down to 28 mbsf. The data yield temperature gradients between ˜38°C km-1 at the deepest site (446 m) and ˜41°C km-1 at a shallower drill site (390 m). These data constrain combined with in situ pore-fluid data, sediment porosities, and thermal conductivities the dynamic evolution of the GHSZ during the past 70 years for which bottom water temperature records exist. Gas hydrate is not stable in the sediments at sites shallower than 390 m water depth at the time of acquisition (August 2016). Only at the drill site in 446 m water depth, favorable gas hydrate stability conditions are met (maximum vertical extent of ˜60 mbsf); however, coring did not encounter any gas hydrates.

Estimates of in situ gas hydrate concentration from resistivity monitoring of gas hydrate bearing sediments during temperature equilibration

USGS Publications Warehouse

Riedel, M.; Long, P.E.; Collett, T.S.

2006-01-01

As part of Ocean Drilling Program Leg 204 at southern Hydrate Ridge off Oregon we have monitored changes in sediment electrical resistivity during controlled gas hydrate dissociation experiments. Two cores were used, each filled with gas hydrate bearing sediments (predominantly mud/silty mud). One core was from Site 1249 (1249F-9H3), 42.1 m below seafloor (mbsf) and the other from Site 1248 (1248C-4X1), 28.8 mbsf. At Site 1247, a third experiment was conducted on a core without gas hydrate (1247B-2H1, 3.6 mbsf). First, the cores were imaged using an infra-red (IR) camera upon recovery to map the gas hydrate occurrence through dissociation cooling. Over a period of several hours, successive runs on the multi-sensor track (includes sensors for P-wave velocity, resistivity, magnetic susceptibility and gamma-ray density) were carried out complemented by X-ray imaging on core 1249F-9H3. After complete equilibration to room temperature (17-18??C) and complete gas hydrate dissociation, the final measurement of electrical resistivity was used to calculate pore-water resistivity and salinities. The calculated pore-water freshening after dissociation is equivalent to a gas hydrate concentration in situ of 35-70% along core 1249F-9H3 and 20-35% for core 1248C-4X1 assuming seawater salinity of in situ pore fluid. Detailed analysis of the IR scan, X-ray images and split-core photographs showed the hydrate mainly occurred disseminated throughout the core. Additionally, in core 1249F-9H3, a single hydrate filled vein, approximately 10 cm long and dipping at about 65??, was identified. Analyses of the logging-while-drilling (LWD) resistivity data revealed a structural dip of 40-80?? in the interval between 40 and 44 mbsf. We further analyzed all resistivity data measured on the recovered core during Leg 204. Generally poor data quality due to gas cracks allowed analyses to be carried out only at selected intervals at Sites 1244, 1245, 1246, 1247, 1248, 1249, and 1252. With a few exceptions, data from these intervals yield low to no gas hydrate concentration, which corresponds to estimates from downhole resistivity logs. However, since the gas cracking may be the result of gas hydrate dissociation, this is a biased sampling. Cores that had contained some gas hydrate may have been excluded. ?? 2005 Elsevier B.V. All rights reserved.

Polyphase serpentinization history of Mariana forearc mantle: observations on the microfabric of ultramafic clasts from ODP Leg 195, Site 1200

NASA Astrophysics Data System (ADS)

Kahl, Wolf-Achim; Jöns, Niels; Bach, Wolfgang; Klein, Frieder

2013-04-01

In the forearc of the Mariana subduction zone system, a number of seamounts form from extrusion of blueschist and serpentine mud. Ocean Drilling Program Leg 195 drilled the South Chamorro seamount, where ultramafic clasts occur within the mud matrix. These clasts show a complex serpentinization history, which bears the potential for tracking the alteration history during uplift and cooling of mantle wedge rocks to the seafloor. Moreover, the microfabrics of the highly serpentinized harzburgite and dunite clasts exhibit evidence for multiple fracturing events in the forearc mantle. These, in turn, lead to fluid influx and varied styles of serpentinization of harzburgite and dunite. The serpentinized ultramafic clasts exhibit a variety of microfabrics that range from virtually undeformed to strongly deformed samples. Pervasively serpentinized harzburgites feature either an equigranular fabric of serpentinized olivine and orthopyroxene crystals, or different vein generations related to multiple stages of serpentinization. Several types of fluid pathways in harzburgites are present: (i) veins containing brucite and iron oxides, developed linearly without marked conformance with the rock fabric. In places, these veins developed mm-cm wide halos with finger-shaped serpentinization fronts. Veins of type (i) are either developed as syntaxial veins from a single crack-seal event with large magnetite crystals growing from one wall to the other (as confirmed with high-resolution X-ray microtomography), or formed by multiple fluid events. (ii) serpentine veins that encompass regions of marginally serpentinized, microgranular olivine and large orthopyroxene crystals. (iii) extensional serpentine veins (known as "Frankenstein" type). In the clasts studied, their occurrence is restricted to the halo region of type (i) veins. (iv) as a late-stage feature, extensional veins documenting multiple crack-seal events can be present in the serpentinites (either in undeformed regions with preserved equigranular fabric, or in serpentinites of type (i) and (ii) where they crosscut and offset earlier vein generations). In addition, serpentinized dunites can host syntaxial serpentine veins (ribbons). The ribbons separate regions, where recrystallization of serpentine and brucite can be observed. Presumably the lack of orthopyroxene locally influences the rheology and thus enable ribbon formation. The serpentine and/or brucite assemblages formed during these different stages show distinct trace element patterns suggesting a diminished influence of slab-related fluids during later stages of serpentinization. Ongoing work is aimed at reconciling textural and geochemical co-evolution during serpentinization of the mantle wedge. In particular, deciphering deformation-related pathways for serpentinizing fluids and identifying their geochemical signatures may foster our understanding of shallow subduction-related mass transfer in supra-subduction zones.

30 CFR 250.418 - What additional information must I submit with my APD?

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to Drill § 250.418 What additional... the drilling rig and major drilling equipment, if not already on file with the appropriate District...

Microbiology of the lower ocean crust - Preliminary results from IODP Expedition 360, Atlantis Bank

NASA Astrophysics Data System (ADS)

Sylvan, J. B.; Edgcomb, V. P.; Burgaud, G.; Klein, F.; Schubotz, F.; Expedition 360 Scientists, I.

2016-12-01

International Ocean Discovery Program (IODP) Expedition 360 represents the first leg of a multi-phase drilling program, SloMo, aimed at investigating the nature of the lower crust and Moho at slow spreading ridges. The goal of Expedition 360 was to recover a representative transect of the lower oceanic crust formed at Atlantis Bank, an oceanic core complex on the SW Indian Ridge. We present here preliminary analysis of microbial communities sampled from Hole U1473A, drilled to 789.7 m below seafloor during Expedition 360. Sub-sampling of core sections was conducted in a newly designed plexiglass enclosure with positive air pressure and HEPA filtered air, providing a clean environment for microbiology sampling aboard the JOIDES Resolution. Adenosine triphosphoate, an indicator of microbial biomass, was quantified above detection in 23 of 66 samples analyzed. We measured exoenzyme activity for alkaline phosphatase (AP), leucine aminopeptidase and arginine aminopeptidase in 16 samples and found AP to be very low but above background for 14 of the samples, with highest activities measured between 10 and 70 m below seafloor (mbsf) and peaks again at 158 and 307 mbsf, while both peptidase enzymes were above detection for only one sample at 715 mbsf. Isolates of fungi obtained from core samples as well as analyses of lipid and DNA biomarkers, and Raman spectra for a few of our rock core samples provide initial insights into microbial communities in the lower oceanic crust. Finally, a new tracer of seawater and drilling mud contamination, perfluoromethyl decaline (PFMD), was tested for the first time and its performance compared with the commonly used tracer perfluoromethylcyclohexane (PMCH). PFMD was run during coring operations for ten samples and was routinely detected in the drilling fluids, usually detected on the outside of uncleaned cores, and rarely above detection on the cleaned outside of cores. It was below detection on the inside of cores, indicating penetration of drill fluids to the interior of whole round drill cores, where we collected our samples, is unlikely.

Results from Testing of Two Rotary Percussive Drilling Systems

NASA Technical Reports Server (NTRS)

Kriechbaum, Kristopher; Brown, Kyle; Cady, Ian; von der Heydt, Max; Klein, Kerry; Kulczycki, Eric; Okon, Avi

2010-01-01

The developmental test program for the MSL (Mars Science Laboratory) rotary percussive drill examined the e ect of various drill input parameters on the drill pene- tration rate. Some of the input parameters tested were drill angle with respect to gravity and percussive impact energy. The suite of rocks tested ranged from a high strength basalt to soft Kaolinite clay. We developed a hole start routine to reduce high sideloads from bit walk. The ongoing development test program for the IMSAH (Integrated Mars Sample Acquisition and Handling) rotary percussive corer uses many of the same rocks as the MSL suite. An additional performance parameter is core integrity. The MSL development test drill and the IMSAH test drill use similar hardware to provide rotation and percussion. However, the MSL test drill uses external stabilizers, while the IMSAH test drill does not have external stabilization. In addition the IMSAH drill is a core drill, while the MSL drill uses a solid powdering bit. Results from the testing of these two related drilling systems is examined.

Source tracking of prokaryotic communities in fermented grain of Chinese strong-flavor liquor.

PubMed

Wang, Xueshan; Du, Hai; Xu, Yan

2017-03-06

The fermentation process of Chinese strong-flavor liquor involves numerous microbes originating from Daqu and pit mud. Daqu is the starter of fermentation, and pit mud acts as another source of inoculum of microbes in the liquor-making process. However, the contribution of microbes in pit mud and Daqu to fermented grain, and the sources of microbes in fermented grain are still waiting to be defined clearly. In this study, prokaryotic communities in fermented grain, pit mud and Daqu were identified via next generation sequencing of the V4 region of 16S rRNA gene. Principal-coordinate analysis indicated that Daqu had stronger influence on the prokaryotic communities in fermented grain at the prophase of fermentation, but pit mud influenced the fermented grain continuously during the whole fermentation process. Totally, 299 genera were detected in all fermented grain, pit mud and Daqu samples. Among them, 204 genera were detected in 3days' fermented grain. Ten genera (Lactobacillus, Leuconostoc, Staphylococcus, Gluconobacter, Acetobacter, Petrimonas, Clostridium, Ruminococcus, Methanobacterium and Methanobrevibacter) were dominant, and accounted for 84.31%-87.13% relative abundance of the total prokaryotic community in fermented grain. Venn analysis indicated Daqu was the main source of strict aerobes and facultative aerobes, which took up over 74% of prokaryotic communities in fermented grain. Conversely, pit mud was the sustained-release source of anaerobes, which accounted for over 14% of prokaryotic communities in fermented grain. In addition, part of anaerobes originated from both Daqu and pit mud. This study could help track the source of prokaryotic communities in fermented grain, and improve the quality and controllability in liquor production. Copyright © 2017 Elsevier B.V. All rights reserved.

Modeling and Recovery of Iron (Fe) from Red Mud by Coal Reduction

NASA Astrophysics Data System (ADS)

Zhao, Xiancong; Li, Hongxu; Wang, Lei; Zhang, Lifeng

Recovery of Fe from red mud has been studied using statistically designed experiments. The effects of three factors, namely: reduction temperature, reduction time and proportion of additive on recovery of Fe have been investigated. Experiments have been carried out using orthogonal central composite design and factorial design methods. A model has been obtained through variance analysis at 92.5% confidence level.

Microbial community stratification controlled by the subseafloor fluid flow and geothermal gradient at the Iheya North hydrothermal field in the Mid-Okinawa Trough (Integrated Ocean Drilling Program Expedition 331).

PubMed

Yanagawa, Katsunori; Breuker, Anja; Schippers, Axel; Nishizawa, Manabu; Ijiri, Akira; Hirai, Miho; Takaki, Yoshihiro; Sunamura, Michinari; Urabe, Tetsuro; Nunoura, Takuro; Takai, Ken

2014-10-01

The impacts of lithologic structure and geothermal gradient on subseafloor microbial communities were investigated at a marginal site of the Iheya North hydrothermal field in the Mid-Okinawa Trough. Subsurface marine sediments composed of hemipelagic muds and volcaniclastic deposits were recovered through a depth of 151 m below the seafloor at site C0017 during Integrated Ocean Drilling Program Expedition 331. Microbial communities inferred from 16S rRNA gene clone sequencing in low-temperature hemipelagic sediments were mainly composed of members of the Chloroflexi and deep-sea archaeal group. In contrast, 16S rRNA gene sequences of marine group I Thaumarchaeota dominated the microbial phylotype communities in the coarse-grained pumiceous gravels interbedded between the hemipelagic sediments. Based on the physical properties of sediments such as temperature and permeability, the porewater chemistry, and the microbial phylotype compositions, the shift in the physical properties of the sediments is suggested to induce a potential subseafloor recharging flow of oxygenated seawater in the permeable zone, leading to the generation of variable chemical environments and microbial communities in the subseafloor habitats. In addition, the deepest section of sediments under high-temperature conditions (∼90°C) harbored the sequences of an uncultivated archaeal lineage of hot water crenarchaeotic group IV that may be associated with the high-temperature hydrothermal fluid flow. These results indicate that the subseafloor microbial community compositions and functions at the marginal site of the hydrothermal field are highly affected by the complex fluid flow structure, such as recharging seawater and underlying hydrothermal fluids, coupled with the lithologic transition of sediments. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

Feasibility of real-time geochemical analysis using LIBS (Laser-Induced Breakdown Spectroscopy) in oil wells

NASA Astrophysics Data System (ADS)

Shahin, Mohamed

2014-05-01

The oil and gas industry has attempted for many years to find new ways to analyze and determine the type of rocks drilled on a real time basis. Mud analysis logging is a direct method of detecting oil and gas in formations drilled, it depends on the "feel" of the bit to decide formation type, as well as, geochemical analysis which was introduced 30 years ago, starting with a pulsed-neutron generator (PNG) based wireline tool upon which LWD technology was based. In this paper, we are studying the feasibility of introducing a new technology for real-time geochemical analysis. Laser-induced breakdown spectroscopy (LIBS) is a type of atomic emission spectroscopy, It is a cutting-edge technology that is used for many applications such as determination of alloy composition, origin of manufacture (by monitoring trace components), and molecular analysis (unknown identification). LIBS can analyze any material regardless of its state (solid, liquid or gas), based upon that fact, we can analyze rocks, formation fluids' types and contacts between them. In cooperation with the National Institute of Laser Enhanced Science, Cairo University in Egypt, we've done tests on sandstone, limestone and coal samples acquired from different places using Nd: YAG Laser with in addition to other components that are explained in details through this paper to understand the ability of Laser to analyze rock samples and provide their elemental composition using LIBS technique. We've got promising results from the sample analysis via LIBS and discussed the possibility of deploying this technology in oilfields suggesting many applications and giving a base for achieving a quantitative elemental analysis method in view of its shortcomings and solutions.

Microbial Community Stratification Controlled by the Subseafloor Fluid Flow and Geothermal Gradient at the Iheya North Hydrothermal Field in the Mid-Okinawa Trough (Integrated Ocean Drilling Program Expedition 331)

PubMed Central

Breuker, Anja; Schippers, Axel; Nishizawa, Manabu; Ijiri, Akira; Hirai, Miho; Takaki, Yoshihiro; Sunamura, Michinari; Urabe, Tetsuro; Nunoura, Takuro; Takai, Ken

2014-01-01

The impacts of lithologic structure and geothermal gradient on subseafloor microbial communities were investigated at a marginal site of the Iheya North hydrothermal field in the Mid-Okinawa Trough. Subsurface marine sediments composed of hemipelagic muds and volcaniclastic deposits were recovered through a depth of 151 m below the seafloor at site C0017 during Integrated Ocean Drilling Program Expedition 331. Microbial communities inferred from 16S rRNA gene clone sequencing in low-temperature hemipelagic sediments were mainly composed of members of the Chloroflexi and deep-sea archaeal group. In contrast, 16S rRNA gene sequences of marine group I Thaumarchaeota dominated the microbial phylotype communities in the coarse-grained pumiceous gravels interbedded between the hemipelagic sediments. Based on the physical properties of sediments such as temperature and permeability, the porewater chemistry, and the microbial phylotype compositions, the shift in the physical properties of the sediments is suggested to induce a potential subseafloor recharging flow of oxygenated seawater in the permeable zone, leading to the generation of variable chemical environments and microbial communities in the subseafloor habitats. In addition, the deepest section of sediments under high-temperature conditions (∼90°C) harbored the sequences of an uncultivated archaeal lineage of hot water crenarchaeotic group IV that may be associated with the high-temperature hydrothermal fluid flow. These results indicate that the subseafloor microbial community compositions and functions at the marginal site of the hydrothermal field are highly affected by the complex fluid flow structure, such as recharging seawater and underlying hydrothermal fluids, coupled with the lithologic transition of sediments. PMID:25063666

Provenance discrimination of sediments in the Zhejiang-Fujian mud belt, East China Sea: Implications for the development of the mud depocenter

NASA Astrophysics Data System (ADS)

Liu, Xiting; Li, Anchun; Dong, Jiang; Lu, Jian; Huang, Jie; Wan, Shiming

2018-01-01

In the past decade, the 800 km elongated mud belt off Zhejiang-Fujian coast, East China Sea (ECS), has been extensively studied for understanding the source to sink processes on the East Asian continental margin in the context of the Asian monsoon. However, to better understand the sediment source and dispersal pattern, the existing mineralogical and geochemical data of adjacent river systems, including the Changjiang River (CJR) and local rivers in Zhejiang, Fujian and Taiwan, need to be systematically reviewed. Therefore, various indicators from published literatures for the provenance discrimination in the mud belt have been summarised in this article. The results show that high diversity of clay mineral assemblages in fluvial sediments being supplied into the mud belt, e.g., dominant illite and chlorite in the CJR, absence of smectite in Taiwan rivers, similar amounts of the four clay mineral species in Zhejiang rivers, and dominant kaolinite in Fujian rivers. On heavy mineralogy, the CJR is dominated by dolomite, hornblende, and flaky minerals; and among of them, dolomite is distinctive for the CJR. For geochemical approaches, elemental compositions, combined with strontium and neodymium isotopes, reflect strong provenance control. However, geochemical and mineralogical compositions are found to vary with grain size, and thus extra caution should be taken when using these parameters as provenance indicator to discriminate the marine sediments with variety of grain-size fractions. In addition, pyrrhotite, occurred in fluvial sediments from western Taiwan, has not been found in sediments derived from mainland China, indicating that magnetic parameters could be used to discriminate sediment provenance. The mud belt formed during sea-level highstand, when modern current system in the ECS has been established, resulting in sediments derived from the CJR have been transported southward since 8 ka. In addition, sediment provenances have not been constant since initiation of the mud belt in response to climatic and oceanographic changes during the Holocene, which has been documented by mineral and geochemical signals. Nevertheless significant studies have been carried out, to better understand the formation mechanism for the mud belt and its implications for environmental changes, further studies on sediment provenance throughout the Holocene, in situ observation, and sedimentation dynamical modelling are required.

Use of Cutting-Edge Horizontal and Underbalanced Drilling Technologies and Subsurface Seismic Techniques to Explore, Drill and Produce Reservoired Oil and Gas from the Fractured Monterey Below 10,000 ft in the Santa Maria Basin of California

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Witter; Robert Knoll; William Rehm

2005-09-29

This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conductedmore » in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper curved sections were drilled and lined through the problematic shale member without major stability problems. The top of the targeted Monterey was thought to be seen at the expected TVD of 10,000 ft where the 7-in. liner was set at a 60{sup o} hole angle. Significant oil and gas shows suggested the fractured interval anticipated at the heel location had been penetrated. A total of 2572 ft of 6 1/8-in. near-horizontal interval was placed in the shale section, extending planned well length by approximately 470 ft. Very little hydrocarbon in-flow was observed from fractures along the productive interval. This may be a result of the well trajectory falling underneath the Monterey fractured zone. Hydrocarbon observations, cuttings analysis and gamma-ray response indicated additional fractured intervals were accessed along the last {+-}900 ft of well length. The well was completed with a 2 7/8-in. tubing string set in a production packer in preparation for flow and swab tests to be conducted later by a service rig. The planned well time was estimated as 39 days and overall cost as $2.4 million. The actual results are 66 days at a total cost of $3.4 million. Well productivity responses during subsequent flow and swabbing tests were negative. The well failed to inflow and only minor amounts (a few barrels) of light oil were recovered. The lack of production may suggest that actual sustainable reservoir pressure is far less than anticipated. Temblor is currently planning to re-enter and clean out the well and run an Array Induction log (primarily for resistivity and correlation purposes), and an FMI log (for fracture detection). Depending on the results of these logs, an acidizing or re-drill program will be planned.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chillara, Vamshi Krishna; Pantea, Cristian; Sinha, Dipen N.

Here, we numerically investigate the resonance and vibration characteristics of radial modes of laterally stiffened piezoelectric disc transducers. Lateral stiffening is modeled using a spring and vibration characteristics of the piezo-disc are investigated with increasing lateral stiffness. It is found that the resonant frequency response of the radial modes follows an asymptotic behavior approaching that of a clamped disc with increasing lateral stiffness. The radial mode vibration pattern of the discs is also found to be affected by lateral stiffness. While the vibration pattern of a free disc corresponds to a Bessel function, laterally stiffened discs show edge-effects where theymore » depart from the Bessel-like behavior. In addition, a fully clamped piezo-disc is found to have an extra side-lobe when compared to a free disc. Ultrasonic beam profiles generated from radial modes of laterally stiffened discs are numerically investigated. It is found that the free piezo-disc generates a Bessel beam that has multiple side-lobes. Increasing the lateral stiffness results in a significant reduction of side-lobes in the beam profile. This technique of generating a collimated beam with side-lobe reduction finds significant applications in imaging through concrete, drilling mud, and other highly attenuating materials.« less

Paleomagnetic investigation of late Quaternary sediments of south San Francisco Bay, California

USGS Publications Warehouse

Hillhouse, John W.

1977-01-01

Paleomagnetic inclinations of the Late Quaternary sediments of South San Francisco Bay were determined from bore hole samples collected near Dumbarton Bridge. The sediments consist of estuarine muds and nonmarine sand deposits, floored by bedrock of the Mesozoic Franciscan Formation. - Beneath Dumbarton Bridge the entire sedimentary fill is normally polarized; therefore, the fill postdates the Brunhes-Matayama polarity reversal (700,000 y. B.P.). Magnetic time lines such as the Mono Lake excursion (24,000 y. B.P.) and the reversed Blake event (110,000 y B.P.) were not found in this bore hole. In addition to Holocene and modern deposits of San Francisco Bay, an older estuarine unit occurs in the stratigraphic section. The older unit was deposited during a period of high sea level, tentatively correlated with the Sangamon interglacial period. Because evidence of the Blake event is not present in the older estuarine unit, the proposed age of this unit could not be confirmed. Although the Holocene estuarine deposits of South San Francisco Bay carry stable remanent magnetization, a reliable record of geomagnetic secular variation could not be recovered because the water-saturated sdiment was deformed by drilling.

Laterally Translating Seal Carrier For A Drilling Mud Motor Sealed Bearing Assembly

DOEpatents

Dietle, Lannie

1993-03-23

A sealing and lubrication assembly for rotating shafts intended for operation in an abrasive environment and wherein the rotary shaft may have lateral translation or excursion during its rotation. A housing receives the rotary shaft in bearing supporting relation and defines a lubricant chamber about the shaft. A seal carrier is movably positioned about the rotary shaft and has non-rotatable articulating or laterally translating relation with the housing. A high pressure rotary shaft seal is supported by the seal carrier and maintains bearing and sealing engagement with the rotary shaft during its lateral translation or excursion. The seal carrier is hydraulic force balanced and thus is not subject to pressure induced loads that might otherwise interfere with its articulation or lateral translation.

Comparison of MWD and wireline applications and decision criteria, Malay Basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zainun, K.; Redzuan, M.; Said, M.

1994-07-01

Since 1987, usage of measurement while drilling (MWD) technology within Esso Production Malaysia Inc. (EPMI) has evolved from an auxiliary directional drilling service to providing a reliable alternative to wireline logs for formation evaluation and well-completion purposes. The shift in EPMI's attitude toward the use of MWD in formation evaluation is attributed to the availability of a complete suite of logging services for the log analysis procedure, accuracy of the data, sufficient control in reservoir quality, and continuity in fields where there are already a high density of wireline-logged wells, increasing number of high angle and horizontal wells being drilled,more » a favorable track record, and realized economic benefits. The in-house analysis procedure, (EPMILOG[sup 6]), requires the availability of a deep and/or shallow investigating resistivity, formation density, neutron porosity, and gamma ray tools for a complete analysis. The availability of these services in MWD and also comparative evaluations of MWD responses with their correlative wireline counterparts show that MWD technology can be used, to a large extent, to complement or replace routine wireline logging services. MWD resistivity measurements are frequently observed to be less effected by mud filtrate invasion than the correlative wireline measurements and are, therefore, closer to the true resistivity of the formation. MWD formation evaluation services are most widely used in fields where there are already a high density of wells that were logged using wireline. The MWD data is used to decide perforation depths and intervals.« less

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take when I conduct drilling... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow...

IODP expedition 347: Baltic Sea basin paleoenvironment and biosphere

NASA Astrophysics Data System (ADS)

Andrén, T.; Barker Jørgensen, B.; Cotterill, C.; Green, S.; IODP expedition 347 scientific party, the

2015-12-01

The Integrated Ocean Drilling Program (IODP) expedition 347 cored sediments from different settings of the Baltic Sea covering the last glacial-interglacial cycle. The main aim was to study the geological development of the Baltic Sea in relation to the extreme climate variability of the region with changing ice cover and major shifts in temperature, salinity, and biological communities. Using the Greatship Manisha as a European Consortium for Ocean Research Drilling (ECORD) mission-specific platform, we recovered 1.6 km of core from nine sites of which four were additionally cored for microbiology. The sites covered the gateway to the North Sea and Atlantic Ocean, several sub-basins in the southern Baltic Sea, a deep basin in the central Baltic Sea, and a river estuary in the north. The waxing and waning of the Scandinavian ice sheet has profoundly affected the Baltic Sea sediments. During the Weichselian, progressing glaciers reshaped the submarine landscape and displaced sedimentary deposits from earlier Quaternary time. As the glaciers retreated they left a complex pattern of till, sand, and lacustrine clay, which in the basins has since been covered by a thick deposit of Holocene, organic-rich clay. Due to the stratified water column of the brackish Baltic Sea and the recurrent and widespread anoxia, the deeper basins harbor laminated sediments that provide a unique opportunity for high-resolution chronological studies. The Baltic Sea is a eutrophic intra-continental sea that is strongly impacted by terrestrial runoff and nutrient fluxes. The Holocene deposits are recorded today to be up to 50 m deep and geochemically affected by diagenetic alterations driven by organic matter degradation. Many of the cored sequences were highly supersaturated with respect to methane, which caused strong degassing upon core recovery. The depth distributions of conservative sea water ions still reflected the transition at the end of the last glaciation from fresh-water clays to Holocene brackish mud. High-resolution sampling and analyses of interstitial water chemistry revealed the intensive mineralization and zonation of the predominant biogeochemical processes. Quantification of microbial cells in the sediments yielded some of the highest cell densities yet recorded by scientific drilling.

Petrophysical characterization of first ever drilled core samples from an active CO2 storage site, the German Ketzin Pilot Site - Comparison with long term experiments

NASA Astrophysics Data System (ADS)

Zemke, Kornelia; Liebscher, Axel

2014-05-01

Petrophysical properties like porosity and permeability are key parameters for a safe long-term storage of CO2 but also for the injection operation itself. These parameters may change during and/or after the CO2 injection due to geochemical reactions in the reservoir system that are triggered by the injected CO2. Here we present petrophysical data of first ever drilled cores from a newly drilled well at the active CO2 storage site - the Ketzin pilot site in the Federal State of Brandenburg, Germany. By comparison with pre-injection baseline data from core samples recovered prior to injection, the new samples provide the unique opportunity to evaluate the impact of CO2 on pore size related properties of reservoir and cap rocks at a real injection site under in-situ reservoir conditions. After injection of 61 000 tons CO2, an additional well was drilled and new rock cores were recovered. In total 100 core samples from the reservoir and the overlaying caprock were investigated by NMR relaxation. Permeability of 20 core samples was estimated by nitrogen and porosity by helium pycnometry. The determined data are comparable between pre-injection and post-injection core samples. The lower part of the reservoir sandstone is unaffected by the injected CO2. The upper part of the reservoir sandstone shows consistently slightly lower NMR porosity and permeability values in the post-injection samples when compared to the pre-injection data. This upper sandstone part is above the fluid level and CO2 present as a free gas phase and a possible residual gas saturation of the cores distorted the NMR results. The potash-containing drilling fluid can also influence these results: NMR investigation of twin samples from inner and outer parts of the cores show a reduced fraction of larger pores for the outer core samples together with lower porosities and T2 times. The drill mud penetration depth can be controlled by the added fluorescent tracer. Due to the heterogeneous character of the Stuttgart Formation it is difficult to estimate definite CO2 induced changes from petrophysical measurements. The observed changes are only minor. Several batch experiments on Ketzin samples drilled prior injection confirm the results from investigation of the in-situ rock cores. Core samples of the pre-injection wells were exposed to CO2 and brine in autoclaves over various time periods. Samples were characterized prior to and after the experiments by NMR and Mercury Injection Porosimetry (MIP). The results are consistent with the logging data and show only minor change. Unfortunately, also in these experiments observed mineralogical and petrophysical changes were within the natural heterogeneity of the Ketzin reservoir and precluded unequivocal conclusions. However, given the only minor differences between post-injection well and pre-injection well, it is reasonable to assume that the potential dissolution-precipitation processes appear to have no severe consequences on reservoir and cap rock integrity or on the injection behaviour. This is also in line with the continuously recorded injection operation parameter. These do not point to any changes in reservoir injectivity.|

Clinical and anti-aging effect of mud-bathing therapy for patients with fibromyalgia.

PubMed

Maeda, Toyoki; Kudo, Yoshihiro; Horiuchi, Takahiko; Makino, Naoki

2017-12-06

Spa bathing is known as a medical treatment for certain diseases causing chronic pains. Spa water contains mineral components which lower the specific heat of the water, resulting in a higher efficiency to warm body-core temperature. This phenomenon yields pain-relieving effect for rheumatoid arthritis, low back pain, sciatic neuralgia, fibromyalgia, etc. Here we introduce medical and biological effects of mud-spa-bathing therapy for fibromyalgia other than pain relief, the changes of blood examination data, and the telomere length of circulating leukocytes. The enrolled 7 patients with fibromyalgia syndrome were hospitalized and were subject to daily mud bathing at 40 °C for 10 min for about a month. Then, their subjective pain was reduced to about a quarter in average. They also showed lowered serum triglyceride and C-reactive protein level, maintaining the levels of aspartate transaminase and creatine phosphokinase, and increases of the red blood cell count, the serum albumin level, and the serum LDL-cholesterol level in comparison with cases without mud-bathing therapy, suggesting that mud bathing prevents inflammation and muscle atrophy and improves nutritional condition in fibromyalgia. In addition, the analysis of telomere length of peripheral leukocytes revealed a trend of negative correlation between telomere shortening and laboratory data change of hemoglobin and serum albumin. These telomeric changes can be explained hypothetically by an effect of mud bathing extending life-span of circulating leukocytes.

Potential risks of the residue from Samarco's mine dam burst (Bento Rodrigues, Brazil).

PubMed

Segura, Fabiana Roberta; Nunes, Emilene Arusievicz; Paniz, Fernanda Pollo; Paulelli, Ana Carolina Cavalheiro; Rodrigues, Gabriela Braga; Braga, Gilberto Úbida Leite; Dos Reis Pedreira Filho, Walter; Barbosa, Fernando; Cerchiaro, Giselle; Silva, Fábio Ferreira; Batista, Bruno Lemos

2016-11-01

On November 5th, 2015, Samarco's iron mine dam - called Fundão - spilled 50-60 million m 3 of mud into Gualaxo do Norte, a river that belongs to Rio Doce Basin. Approximately 15 km 2 were flooded along the rivers Gualaxo do Norte, Carmo and Doce, reaching the Atlantic Ocean on November 22nd, 2015. Six days after, our group collected mud, soil and water samples in Bento Rodrigues (Minas Gerais, Brazil), which was the first impacted area. Overall, the results, water samples - potable and surface water from river - presented chemical elements concentration according to Brazilian environmental legislations, except silver concentration in surface water that ranged from 1.5 to 1087 μg L -1 . In addition, water mud-containing presented Fe and Mn concentrations approximately 4-fold higher than the maximum limit for water bodies quality assessment, according to Brazilian laws. Mud particle size ranged from 1 to 200 μm. SEM-EDS spot provided us some semi quantitative data. Leaching/extraction tests suggested that Ba, Pb, As, Sr, Fe, Mn and Al have high potential mobilization from mud to water. Low microbial diversity in mud samples compared to background soil samples. Toxicological bioassays (HepG2 and Allium cepa) indicated potential risks of cytotoxicity and DNA damage in mud and soil samples used in both assays. The present study provides preliminary information aiming to collaborate to the development of future works for monitoring and risk assessment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluation of Gas Hydrate at Alaminos Canyon 810, Northern Gulf of Mexico Slope

NASA Astrophysics Data System (ADS)

Yang, C.; Cook, A.; Sawyer, D.; Hillman, J. I. T.

2016-12-01

We characterize the gas hydrate reservoir in Alaminos Canyon Block 810 (AC810) on the northern Gulf of Mexico slope, approximately 400 km southeast of Houston, Texas, USA. Three-dimensional seismic data shows a bottom-simulating-reflection (BSR), over 30 km2, which suggests that a significant gas hydrate accumulation may occur at AC810. Furthermore, logging while drilling (LWD) data acquired from a Statoil well located that penetrated the BSR near the crest of the regional anticline indicates two possible gas hydrate units (Hydrate Unit A and Hydrate Unit B). LWD data in this interval are limited to gamma ray and resistivity only. Resistivity curve separations are observed in Hydrate Unit A (131 to 253 mbsf) suggesting hydrate-filled fractures in marine mud. A spiky high resistivity response in Hydrate Unit B (308 to 354 mbsf) could either be a marine mud or a sand-prone interval. The abrupt decrease (from 7 to 1 Ωm) in resistivity logs at 357 mbsf generally corresponds with the interpreted base of hydrate stability, as the BSR is observed near 350 mbsf on the seismic data. To further investigate the formation characteristics, we generate synthetic traces using general velocity and density trends for marine sediments to match the seismic trace extracted at the Statoil well. We consider models with 1) free gas and 2) water only below the base of hydrate stability. In our free gas-below models, we find the velocity of Hydrate Unit A and Hydrate Unit B is generally low and does not deviate significantly from the general velocity trends, suggesting that gas hydrate is present in a marine mud. In the water-below model, the compressional velocity of Hydrate Unit B ranges from 2450 m/s to 3150 m/s. This velocity is similar to the velocity of high hydrate saturation in sand; typically greater than 2500 m/s. This may indicate that Hydrate Unit B is sand with high hydrate saturation; however, to achieve a suitable match between the water-below synthetic seismogram and the trace, a high velocity layer was required below the base of hydrate stability, which is not indicated by the well logs. Our models indicate that at AC810, Hydrate Unit A probably contains hydrate filled fractures in a marine mud. For Hydrate Unit B, our models suggest hydrate may occur in a sand-prone interval, but is more likely to be gas hydrate filled fractures in marine mud.

Microbial diversity in Frenulata (Siboglinidae, Polychaeta) species from mud volcanoes in the Gulf of Cadiz (NE Atlantic).

PubMed

Rodrigues, Clara F; Hilário, Ana; Cunha, Marina R; Weightman, Andrew J; Webster, Gordon

2011-06-01

Frenulates are a group of gutless marine annelids belonging to the Siboglinidae that are nutritionally dependent upon endosymbiotic bacteria. We have characterized the bacteria associated with several frenulate species from mud volcanoes in the Gulf of Cadiz by PCR-DGGE of bacterial 16S rRNA genes, coupled with analysis of 16S rRNA gene libraries. In addition to the primary symbiont, bacterial consortia (microflora) were found in all species analysed. Phylogenetic analyses indicate that the primary symbiont in most cases belongs to the Gammaproteobacteria and were related to thiotrophic and methanotrophic symbionts from other marine invertebrates, whereas members of the microflora were related to multiple bacterial phyla. This is the first molecular evidence of methanotrophic bacteria in at least one frenulate species. In addition, the occurrence of the same bacterial phylotype in different Frenulata species, from different depths and mud volcanoes suggests that there is no selection for specific symbionts and corroborates environmental acquisition as previously proposed for this group of siboglinids.

A workshop model simulating fate and effect of drilling muds and cuttings on benthic communities

USGS Publications Warehouse

Auble, Gregor T.; Andrews, Austin K.; Hamilton, David B.; Roelle, James E.; Shoemaker, Thomas G.

1984-01-01

Oil and gas exploration and production at marine sites has generated concern over potential environmental impacts resulting from the discharge of spent drilling muds and cuttings. This concern has led to a broad array of publicly and privately sponsored research. This report described a cooperative modeling effort designed to focus information resulting from this research through construction of explicit equations that simulate the potential impacts of discharge drilling fluids (muds) and cuttings on marine communities. The model is the result of collaboration among more than 30 scientists. The principal cooperating organizations were the E.S. Environmental Protection Agency, the U.S. Minerals Management Service, the Offshore Operators Committee, and the Alaska Oil and Gas Association. The overall simulation model can be conceptualized as three connected submodels: Discharge and Plume Fate, Sediment Redistribution, and Benthic Community Effects. On each day of simulation, these submodels are executed in sequence, with flows of information between submodels. The Benthic Community Effects submodel can be further divided into sections that calculate mortality due to burial, mortality due to toxicity, mortality due to resuspension disturbance, and growth of the community. The model represents a series of seven discrete 1-m2 plots at specified distances along a transect in one direction away from a discharge point. It consists of coupled difference equations for which parameter values can easily be set to evaluate different conditions or to examine the sensitivity of output to various assumptions. Sets of parameter values were developed to represent four general cases or scenarios: (1) a shallow (5 m), cold environment with ice cover during a substantial fraction of the year, such as might be encountered in the Beaufort Sea, Alaska; (2) a shallow (20 m), temperate environment, such as might be encountered in the Gulf of Mexico; (3) a deeper (80 m), temperate environment, such as might be encountered in the Gulf of Mexico; and (4) a very deep (1,000 m) environment, such as might be encountered on the Atlantic slope. The focus of the modeling effort was on the connection of a reasonable representation of physical fate to the biological responses of populations, rather than on highly detailed representations of individual processes. For example, the calculations of physical fate are not as detailed as those in the recently published model of Brandsma et al. (1983). The value of the model described herein is in the broad scope of processes that are explicitly represented and linked together. The model cannot be considered to produce reliable predictions of the quantitative impacts of discharged drilling fluids and cuttings on biological populations at a particular site. Limitations of the model in predicting integrated fate and effects can be traced to three general areas: level of refinement of the algorithms used in the model; lack of understanding of the processes determining fate and effects; and parameter and data values. Despite the limitations, several qualitative conclusions concerning both potential impacts and the importance of various remaining data gaps can be drawn from the modeling effort. These include: (1) Simple, unequivocal conclusions about fate and effects across geographical regions and drilling operations are difficult, if not misleading, due to the large amount of variability in characteristics of discharged materials (e.g., oil content and toxicity), discharge conditions (e.g., duration of drilling operations), physical environments (e.g., water depth, current direction, and sediment disturbance regimes), and biological communities (e.g., intrinsic growth rates). Different combinations of these characteristics can result in substantial differences in simulated environmental fate and biological effects. For examples, simulated recovery in some high-energy environments occurs within months after the cessation of discharge operations, even at heavily impacted sites, whereas simulated recover in some low-energy environments takes years at heavily impacted sites. (3) The volume of material discharged and duration of operations in the production drilling operations simulated by the model are sufficient to produce substantial simulated biological impacts at some plots, both in terms of differences from a control plot during the period of discharge operations, and in terms of the recovery period following the perturbations. Evaluation of the significance of potential effects involves the following factors: • Definition of a specific spatial and temporal reference frame (e.g., What is the natural variation? Is 1 year to be considered a "long" or "short" time? Is 50 m to be considered a "large" or "trivial" distance? • Consideration of rare or unique resources and particularly sensitive biotic assemblages. • Consideration of the potential for long term, cumulative effects. Some of these aspects are clearly beyond the scope of this modeling efforts (e.g., the model does not simulate the long term fate of resuspended material). The model does, however, contain an internal "reference frame" by comparison to simulated behavior at a control plot. The model, in general, simulates substantial "natural" variation at the reference or control plots, both over time, due to sediment disturbance events in medium to high energy environments, and over space, due to geographically varying conditions, such as water depth and current regime.

Geophysical investigation, Salmon Site, Lamar County, Mississippi

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Geophysical surveys were conducted in 1992 and 1993 on 21 sites at the Salmon Site (SS) located in Lamar County, Mississippi. The studies are part of the Remedial Investigation/Feasibility Study (RI/FS) being conducted by IT Corporation for the U.S. Department of Energy (DOE). During the 1960s, two nuclear devices and two chemical tests were detonated 826 meters (in) (2710 feet [ft]) below the ground surface in the salt dome underlying the SS. These tests were part of the Vela Uniform Program conducted to improve the United States capability to detect, identify, and locate underground nuclear detonations. The RI/FS is beingmore » conducted to determine if any contamination is migrating from the underground shot cavity in the salt dome and if there is any residual contamination in the near surface mud and debris disposal pits used during the testing activities. The objective of the surface geophysical surveys was to locate buried debris, disposal pits, and abandoned mud pits that may be present at the site. This information will then be used to identify the locations for test pits, cone penetrometer tests, and drill hole/monitor well installation. The disposal pits were used during the operation of the test site in the 1960s. Vertical magnetic gradient (magnetic gradient), electromagnetic (EM) conductivity, and ground-penetrating radar (GPR) surveys were used to accomplish these objectives. A description of the equipment used and a theoretical discussion of the geophysical methods are presented Appendix A. Because of the large number of figures relative to the number of pages of text, the geophysical grid-location maps, the contour maps of the magnetic-gradient data, the contour maps of the EM conductivity data, and the GPR traverse location maps are located in Appendix B, Tabs I through 22. In addition, selected GPR records are located in Appendix C.« less

In situ stabilization of cadmium-, lead-, and zinc-contaminated soil using various amendments.

PubMed

Lee, Sang-Hwan; Lee, Jin-Soo; Choi, Youn Jeong; Kim, Jeong-Gyu

2009-11-01

Chemical stabilization is an in situ remediation method that uses inexpensive amendments to reduce contaminant availability in polluted soil. We tested the effects of several amendments (limestone, red-mud, and furnace slag) on the extractability of heavy metals, microbial activities, phytoavailability of soil metals (assessed using lettuce, Lactuca sativa L.), and availability of heavy metals in ingested soil to the human gastrointestinal system (assessed using the physiologically based extraction test). The application of soil amendments significantly decreased the amount of soluble and extractable heavy metals in the soil (p<0.05). The decreased extractable metal content of soil was accompanied by increased microbial activity and decreased plant uptake of heavy metals. Soil microbial activities (soil respiration, urease, and dehydrogenase activity) significantly increased in limestone and red-mud-amended soils. Red-mud was the most effective treatment in decreasing heavy-metal concentrations in lettuce. Compared to non-amended control soil, lettuce uptake of Cd, Pb, and Zn was reduced 86%, 58%, and 73%, respectively, by the addition of red-mud.

USE OF CUTTING-EDGE HORIZONTAL AND UNDERBALANCED DRILLING TECHNOLOGIES AND SUBSURFACE SEISMIC TECHNIQUES TO EXPLORE, DRILL AND PRODUCE RESERVOIRED OIL AND GAS FROM THE FRACTURED MONTEREY BELOW 10,000 FT IN THE SANTA MARIA BASIN OF CALIFORNIA

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Witter; Robert Knoll; William Rehm

2005-02-01

This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area by Temblor Petroleum with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial projectmore » meetings were conducted in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper curved sections were drilled and lined through the problematic shale member without major stability problems. The top of the targeted Monterey was thought to be seen at the expected TVD of 10,000 ft where the 7-in. liner was set at a 60{sup o} hole angle. Significant oil and gas shows suggested the fractured interval anticipated at the heel location had been penetrated. A total of 2572 ft of 6.-in. near-horizontal interval was placed in the shale section, extending planned well length by approximately 470 ft. Very little hydrocarbon in-flow was observed from fractures along the productive interval. This may be a result of the well trajectory falling underneath the Monterey fractured zone. Hydrocarbon observations, cuttings analysis and gamma-ray response indicated additional fractured intervals were accessed along the last {+-}900 ft of well length. The well was completed with a 2 7/8-in. tubing string set in a production packer in preparation for flow and swab tests to be conducted later by a service rig. The planned well time was estimated as 39 days and overall cost as $2.4 million. The actual results are 66 days at a total cost of $3.4 million. Well productivity responses during subsequent flow and swabbing tests were negative. The well failed to inflow and only minor amounts (a few barrels) of light oil were recovered. The lack of production may suggest that actual sustainable reservoir pressure is far less than anticipated. Temblor is currently investigating the costs and operational viability of re-entering the well and conducting an FMI (fracture detection) log and/or an acid stimulation. No final decision or detailed plans have been made regarding these potential interventions at this time.« less

Addendum to the Closure Report for Corrective Action Unit 355: Area 2 Cellars/Mud Pits Nevada Test Site, Nevada, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lynn Kidman

This document constitutes an addendum to the November 2003, Closure Report for Corrective Action Unit 355: Area 2 Cellars/Mud Pits as described in the document Recommendations and Justifications for Modifications for Use Restrictions Established under the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office Federal Facility Agreement and Consent Order (UR Modification document) dated February 2008. The UR Modification document was approved by NDEP on February 26, 2008. The approval of the UR Modification document constituted approval of each of the recommended UR modifications. In conformance with the UR Modification document, this addendum consists of: • Thismore » cover page that refers the reader to the UR Modification document for additional information • The cover and signature pages of the UR Modification document • The NDEP approval letter • The corresponding section of the UR Modification document This addendum provides the documentation justifying the cancellation of the URs for: • CAS 02-37-01, Cellar & Mud Pit • CAS 02-37-03, Cellar & Mud Pit • CAS 02-37-04, Cellar & Mud Pit • CAS 02-37-05, Cellar & Mud Pit • CAS 02-37-06, Cellar & Mud Pit • CAS 02-37-07, Cellar & Mud Pit • CAS 02-37-10, Cellar & Mud Pit • CAS 02-37-11, Cellar & Mud Pit • CAS 02-37-12, Cellar & Mud Pit • CAS 02-37-13, Cellar & Mud Pit • CAS 02-37-14, Cellar & Mud Pit • CAS 02-37-15, Cellar & Mud Pit • CAS 02-37-16, Cellar & Mud Pit • CAS 02-37-17, Cellar • CAS 02-37-18, Cellar & Tanks These URs were established as part of Federal Facility Agreement and Consent Order (FFACO) corrective actions and were based on the presence of contaminants at concentrations greater than the action levels established at the time of the initial investigation (FFACO, 1996; as amended August 2006). Since these URs were established, practices and procedures relating to the implementation of risk-based corrective actions (RBCA) have changed. Therefore, these URs were re-evaluated against the current RBCA criteria as defined in the Industrial Sites Project Establishment of Final Action Levels (NNSA/NSO, 2006c). This re-evaluation consisted of comparing the original data (used to define the need for the URs) to risk-based final action levels (FALs) developed using the current Industrial Sites RBCA process. The re-evaluation resulted in a recommendation to remove these URs because contamination is not present at these sites above the risk-based FALs. Requirements for inspecting and maintaining these URs will be canceled, and the postings and signage at each site will be removed. Fencing and posting may be present at these sites that are unrelated to the FFACO URs such as for radiological control purposes as required by the NV/YMP Radiological Control Manual (NNSA/NSO, 2004f). This modification will not affect or modify any non-FFACO requirements for fencing, posting, or monitoring at these sites.« less

Quantitative X-ray Diffraction (QXRD) analysis for revealing thermal transformations of red mud.

PubMed

Liao, Chang-Zhong; Zeng, Lingmin; Shih, Kaimin

2015-07-01

Red mud is a worldwide environmental problem, and many authorities are trying to find an economic solution for its beneficial application or/and safe disposal. Ceramic production is one of the potential waste-to-resource strategies for using red mud as a raw material. Before implementing such a strategy, an unambiguous understanding of the reaction behavior of red mud under thermal conditions is essential. In this study, the phase compositions and transformation processes were revealed for the Pingguo red mud (PRM) heat-treated at different sintering temperatures. Hematite, perovskite, andradite, cancrinite, kaolinite, diaspore, gibbsite and calcite phases were observed in the samples. However, unlike those red mud samples from the other regions, no TiO2 (rutile or anatase) or quartz were observed. Titanium was found to exist mainly in perovskite and andradite while the iron mainly existed in hematite and andradite. A new silico-ferrite of calcium and aluminum (SFCA) phase was found in samples treated at temperatures above 1100°C, and two possible formation pathways for SFCA were suggested. This is the first SFCA phase to be reported in thermally treated red mud, and this finding may turn PRM waste into a material resource for the iron-making industry. Titanium was found to be enriched in the perovskite phase after 1200°C thermal treatment, and this observation indicated a potential strategy for the recovery of titanium from PRM. In addition to noting these various resource recovery opportunities, this is also the first study to quantitatively summarize the reaction details of PRM phase transformations at various temperatures. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mechanism of red mud combined with Fenton's reagent in sewage sludge conditioning.

PubMed

Zhang, Hao; Yang, Jiakuan; Yu, Wenbo; Luo, Sen; Peng, Li; Shen, Xingxing; Shi, Yafei; Zhang, Shinan; Song, Jian; Ye, Nan; Li, Ye; Yang, Changzhu; Liang, Sha

2014-08-01

Red mud was evaluated as an alternative skeleton builder combined with Fenton's reagent in sewage sludge conditioning. The results show that red mud combined with Fenton's reagent showed good conditioning capability with the pH of the filtrate close to neutrality, indicating that red mud acted as a neutralizer as well as a skeleton builder when jointly used with Fenton's reagent. Through response surface methodology (RSM), the optimal dosages of Fe(2+), H2O2 and red mud were proposed as 31.9, 33.7 and 275.1 mg/g DS (dry solids), respectively. The mechanism of the composite conditioner could be illuminated as follows: (1) extracellular polymeric substances (EPS), including loosely bound EPS and tightly bound EPS, were degraded into dissolved organics, e.g., proteins and polysaccharides; (2) bound water was released and converted into free water due to the degradation of EPS; and (3) morphology of the conditioned sludge exhibited a porous structure in contrast with the compact structure of raw sludge, and the addition of red mud formed new mineral phases and a rigid lattice structure in sludge, allowing the outflow of free water. Thus, sludge dewatering performance was effectively improved. The economic assessment for a wastewater treatment plant of 370,000 equivalent inhabitants confirms that using red mud conditioning, combined with Fenton's reagent, leads to a saving of approximately 411,000 USD/y or 50.8 USD/t DS comparing with using lime and ordinary Portland cement combined with Fenton's reagent, and approximately 612,000 USD/y or 75.5 USD/t DS comparing with the traditional treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

Experimental Study of Sand Production and Mud Erosion Phenomena for Sand Mud Alternate Layer

NASA Astrophysics Data System (ADS)

Oyama, H.; Sato, T.

2014-12-01

Methane hydrates are crystalline, ice-like compounds under specific thermodynamic conditions. The existence of methane hydrates is confirmed in the Nankai Trough, an offshore area of Japan. Japan's Methane Hydrate Research and Development Program (MH21) has been under way at this area. In the early 2013, the world's first intentional gas production attempt from marine gas hydrate deposits was tried and accomplished in the Daini Atumi Knoll area of the Eastern Nankai Trough. For gas production, depressurization method has been considered as a promising gas production technique from methane hydrate reservoirs. However, considering of continuous gas production over a long period, there is still something to clarify. The methane hydrate crystals are very small and existed in the intergranular pores of sandy layer of turbidite sediments. When the intergranular methane hydrates will be dissociated, it is considered that dissociated gas and water flow will cause sand production and mud erosion phenomena of turbidite sediments. The production of framework sands into a well is one of the problems plaguing the gas because of its adverse effects on well productivity and equipment. If the eroded mud is accumulated in the pore space of sand, skin is generated and permeability becomes lower. In addition, mud erosion has a negative effect for the well stability. This research presents an experimental study to understand sand production and mud erosion phenomena for sand mud alternate layer. The aims of this study are to understand these phenomena and clarify driving forces. In our experiments, we used an artificial sedimentary core and performed experiments under various conditions. As the results, the driving forces of these phenomena are not dissociation gas flow but water flow through pore.

Comparison of health service use among veterans with methamphetamine versus alcohol use disorders.

PubMed

Morasco, Benjamin J; OʼNeil, Maya E; Duckart, Jonathan P; Ganzini, Linda

2014-01-01

Methamphetamine use disorders (MUD) are associated with severe health effects and psychiatric comorbidities, but little is known about the health care utilization of patients with MUD. The goal of this study was to describe health service use among veterans with MUD relative to a group of veterans with an alcohol use disorder (AUD). Using Veterans Affairs (VA) administrative data, we identified 718 patients who were diagnosed with MUD and had confirmatory drug testing. Data were compared with those of 744 patients who had diagnoses of an AUD also with confirmatory testing. We examined diagnoses and medical utilization for 5 years after their index date. Patients with MUD and laboratory-confirmed recent use were younger and more likely to be diagnosed with a mood disorder, posttraumatic stress disorder, and a psychotic-spectrum disorder (all P values < 0.05). After statistical controls, patients with MUD were more likely to have an inpatient hospitalization (80% vs 70%, odds ratio [OR] = 1.8; 95% confidence interval [CI] = 1.4-2.3), discharge from an inpatient admission against medical advice (23.4% vs 8.3%, OR = 2.6, 95% CI = 1.9-3.7), receive care at 3 or more VA medical centers (13.1% vs 5.4%, OR = 2.3, 95% CI = 1.5-3.5), have a behavioral flag in the medical record (5.6% vs 1.1%, OR = 4.6, 95% CI = 2.1-10.6), and have more total missed appointments in the 5-year study period (M = 33.1 vs M = 23.5, P < 0.001). Among veterans with substance use disorders, those with MUD and laboratory-confirmed recent use have additional behavioral, health care utilization, and psychiatric characteristics that need to be considered in developing programs of care.

Genesis of mud volcano fluids in the Gulf of Cadiz - A novel model approach

NASA Astrophysics Data System (ADS)

Schmidt, Christopher; Burwicz, Ewa; Hensen, Christian; Martínez-Loriente, Sara; Wallmann, Klaus; Gràcia, Eulàlia

2017-04-01

Mud volcanism and fluid seepage are common phenomena on the continental margin in the Gulf of Cadiz, North East Atlantic Ocean. Over the past 2 decades more than 50 mud volcanoes have been discovered and investigated interdisciplinarily. Mud volcano fluids emanating at these sites are sourced at great depths and migration is often mediated by strike slip faults in a seismically active region. The geochemical signals of the mud volcano fluids are affected by widespread various processes such as clay mineral dehydration, but also the recrystallization of ancient carbonate rocks and the alteration of oceanic crust have been suggested (Hensen et al., 2015). We developed a novel fully-coupled, basin-scale, reaction-transport model with an adaptive numerical mesh to simulate the fluid genesis in this region. An advantage of this model is the coupling of a realistic geophysical and geochemical approach, considering a growing sediment column over time together with instant compaction of sediments as well as diffusion and advection of dissolved pore water species and chemical reactions. In this proof of concept study, we looked at various scenarios to identify the processes of fluid genesis for 4 mud volcanoes, representing combinations in different subsurface settings. We can reproduce the fluid signatures (chloride, strontium, 87Sr/86Sr) of all mud volcanoes. Furthermore, we can give additional evidence that alteration of oceanic crust by fluid flow is a likely process affecting the fluid composition. Hensen, C., Scholz, F., Nuzzo, M., Valadares, V., Gràcia, E., Terrinha, P., Liebetrau, V., Kaul, N., Silva, S., Martínez-Loriente, S., Bartolome, R., Piñero, E., Magalhães, V. H., Schmidt, M., Weise, S. M., Cunha, M., Hilario, A., Perea, H., Rovelli, L., and Lackschewitz, K., 2015, Strike-slip faults mediate the rise of crustal-derived fluids and mud volcanism in the deep sea: Geology, v. 43, no. 4, p. 339-342.

46 CFR 199.250 - Drills.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Drills. 199.250 Section 199.250 Shipping COAST GUARD... CERTAIN INSPECTED VESSELS Additional Requirements for Passenger Vessels § 199.250 Drills. (a) An abandon-ship drill and a fire drill, as described in § 199.180, must be conducted on each passenger vessel at...

46 CFR 199.250 - Drills.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Drills. 199.250 Section 199.250 Shipping COAST GUARD... CERTAIN INSPECTED VESSELS Additional Requirements for Passenger Vessels § 199.250 Drills. (a) An abandon-ship drill and a fire drill, as described in § 199.180, must be conducted on each passenger vessel at...

46 CFR 199.250 - Drills.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Drills. 199.250 Section 199.250 Shipping COAST GUARD... CERTAIN INSPECTED VESSELS Additional Requirements for Passenger Vessels § 199.250 Drills. (a) An abandon-ship drill and a fire drill, as described in § 199.180, must be conducted on each passenger vessel at...

46 CFR 199.250 - Drills.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Drills. 199.250 Section 199.250 Shipping COAST GUARD... CERTAIN INSPECTED VESSELS Additional Requirements for Passenger Vessels § 199.250 Drills. (a) An abandon-ship drill and a fire drill, as described in § 199.180, must be conducted on each passenger vessel at...

46 CFR 199.250 - Drills.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Drills. 199.250 Section 199.250 Shipping COAST GUARD... CERTAIN INSPECTED VESSELS Additional Requirements for Passenger Vessels § 199.250 Drills. (a) An abandon-ship drill and a fire drill, as described in § 199.180, must be conducted on each passenger vessel at...

Deep-sea geohazards in the South China Sea

NASA Astrophysics Data System (ADS)

Wu, Shiguo; Wang, Dawei; Völker, David

2018-02-01

Various geological processes and features that might inflict hazards identified in the South China Sea by using new technologies and methods. These features include submarine landslides, pockmark fields, shallow free gas, gas hydrates, mud diapirs and earthquake tsunami, which are widely distributed in the continental slope and reefal islands of the South China Sea. Although the study and assessment of geohazards in the South China Sea came into operation only recently, advances in various aspects are evolving at full speed to comply with National Marine Strategy and `the Belt and Road' Policy. The characteristics of geohazards in deep-water seafloor of the South China Sea are summarized based on new scientific advances. This progress is aimed to aid ongoing deep-water drilling activities and decrease geological risks in ocean development.

Adaptation of Soil Physical Measurement Techniques for the Delineation of Mud and Lakebed Sediments at Neusiedler See

PubMed Central

Kogelbauer, Ilse; Heine, Erwin; D'Amboise, Christopher; Müllebner, Christoph; Sokol, Wolfgang; Loiskandl, Willibald

2013-01-01

For many water management issues of shallow lakes with non-consolidated sediments hydrographic surveys of the open water area and reed belt areas are required. In the frame of water management strategy for the steppe lake Neusiedler See, located between Austria and Hungary, a hydrographic survey was conducted. In the open water area (water depth ≥1 m) a sediment echosounder was used. To validate these measurements and to distinguish between water, mud, and sediment layers in the shallow lake and reed belt area additional measurements were needed. As no common standard methods are available yet, we developed a measurement system based on two commonly applied soil physical measurement techniques providing reproducible physical values: a capacitive sensor and a cone penetrometer combined with GNSS-positioning enable dynamic measurements of georeferenced vertical water-mud-bedsediments profiles. The system bases on site-specific calibrated sensors and allows instantaneous, in situ measurements. The measurements manifest a sharp water-mud interface by a sudden decline to smaller water content which is a function of the dielectric permittivity. A second decline indicates the transition to compacted mud. That is concurrently the density where the penetrometer starts registering significant penetration resistance. The penetrometer detects shallow lakebed-sediment layers. Within the lake survey this measurement system was successfully tested. PMID:24351626

New Insight into Sugarcane Industry Waste Utilization (Press Mud) for Cleaner Biobutanol Production by Using C. acetobutylicum NRRL B-527.

PubMed

Nimbalkar, Pranhita R; Khedkar, Manisha A; Gaikwad, Shashank G; Chavan, Prakash V; Bankar, Sandip B

2017-11-01

In the present study, press mud, a sugar industry waste, was explored for biobutanol production to strengthen agricultural economy. The fermentative production of biobutanol was investigated via series of steps, viz. characterization, drying, acid hydrolysis, detoxification, and fermentation. Press mud contains an adequate amount of cellulose (22.3%) and hemicellulose (21.67%) on dry basis, and hence, it can be utilized for further acetone-butanol-ethanol (ABE) production. Drying experiments were conducted in the temperature range of 60-120 °C to circumvent microbial spoilage and enhance storability of press mud. Furthermore, acidic pretreatment variables, viz. sulfuric acid concentration, solid to liquid ratio, and time, were optimized using response surface methodology. The corresponding values were found to be 1.5% (v/v), 1:5 g/mL, and 15 min, respectively. In addition, detoxification studies were also conducted using activated charcoal, which removed almost 93-97% phenolics and around 98% furans, which are toxic to microorganisms during fermentation. Finally, the batch fermentation of detoxified press mud slurry (the sample dried at 100 °C and pretreated) using Clostridium acetobutylicum NRRL B-527 resulted in a higher butanol production of 4.43 g/L with a total ABE of 6.69 g/L.

Physicochemical impacts associated with natural gas development on methanogenesis in deep sand aquifers.

PubMed

Katayama, Taiki; Yoshioka, Hideyoshi; Muramoto, Yoshiyuki; Usami, Jun; Fujiwara, Kazuhiro; Yoshida, Satoshi; Kamagata, Yoichi; Sakata, Susumu

2015-02-01

The Minami-Kanto gas field, where gases are dissolved in formation water, is a potential analogue for a marine gas hydrate area because both areas are characterized by the accumulation of microbial methane in marine turbidite sand layers interbedded with mud layers. This study examined the physicochemical impacts associated with natural gas production and well drilling on the methanogenic activity and composition in this gas field. Twenty-four gas-associated formation water samples were collected from confined sand aquifers through production wells. The stable isotopic compositions of methane in the gases indicated their origin to be biogenic via the carbonate reduction pathway. Consistent with this classification, methanogenic activity measurements using radiotracers, culturing experiments and molecular analysis of formation water samples indicated the predominance of hydrogenotrophic methanogenesis. The cultivation of water samples amended only with methanogenic substrates resulted in significant increases in microbial cells along with high-yield methane production, indicating the restricted availability of substrates in the aquifers. Hydrogenotrophic methanogenic activity increased with increasing natural gas production from the corresponding wells, suggesting that the flux of substrates from organic-rich mudstones to adjacent sand aquifers is enhanced by the decrease in fluid pressure in sand layers associated with natural gas/water production. The transient predominance of methylotrophic methanogens, observed for a few years after well drilling, also suggested the stimulation of the methanogens by the exposure of unutilized organic matter through well drilling. These results provide an insight into the physicochemical impacts on the methanogenic activity in biogenic gas deposits including marine gas hydrates.

Lithologic and ground-water-quality data collected using Hoverprobe drilling techniques at the West Branch Canal Creek wetland, Aberdeen Proving Ground, Maryland, April-May 2000

USGS Publications Warehouse

Phelan, Daniel J.; Senus, Michael P.; Olsen, Lisa D.

2001-01-01

This report presents lithologic and groundwater- quality data collected during April and May 2000 in the remote areas of the tidal wetland of West Branch Canal Creek, Aberdeen Proving Ground, Maryland. Contamination of the Canal Creek aquifer with volatile organic compounds has been documented in previous investigations of the area. This study was conducted to investigate areas that were previously inaccessible because of deep mud and shallow water, and to support ongoing investigations of the fate and transport of volatile organic compounds in the Canal Creek aquifer. A unique vibracore drill rig mounted on a hovercraft was used for drilling and groundwater sampling. Continuous cores of the wetland sediment and of the Canal Creek aquifer were collected at five sites. Attempts to sample ground water were made by use of a continuous profiler at 12 sites, without well installation, at a total of 81 depths within the aquifer. Of those 81 attempts, only 34 sampling depths produced enough water to collect samples. Ground-water samples from two sites had the highest concentrations of volatile organic compounds?with total volatile organic compound concentrations in the upper part of the aquifer ranging from about 15,000 to 50,000 micrograms per liter. Ground-water samples from five sites had much lower total volatile organic compound concentrations (95 to 2,100 micrograms per liter), whereas two sites were essentially not contaminated, with total volatile organic compound concentrations less than or equal to 5 micrograms per liter.

Physicochemical impacts associated with natural gas development on methanogenesis in deep sand aquifers

PubMed Central

Katayama, Taiki; Yoshioka, Hideyoshi; Muramoto, Yoshiyuki; Usami, Jun; Fujiwara, Kazuhiro; Yoshida, Satoshi; Kamagata, Yoichi; Sakata, Susumu

2015-01-01

The Minami-Kanto gas field, where gases are dissolved in formation water, is a potential analogue for a marine gas hydrate area because both areas are characterized by the accumulation of microbial methane in marine turbidite sand layers interbedded with mud layers. This study examined the physicochemical impacts associated with natural gas production and well drilling on the methanogenic activity and composition in this gas field. Twenty-four gas-associated formation water samples were collected from confined sand aquifers through production wells. The stable isotopic compositions of methane in the gases indicated their origin to be biogenic via the carbonate reduction pathway. Consistent with this classification, methanogenic activity measurements using radiotracers, culturing experiments and molecular analysis of formation water samples indicated the predominance of hydrogenotrophic methanogenesis. The cultivation of water samples amended only with methanogenic substrates resulted in significant increases in microbial cells along with high-yield methane production, indicating the restricted availability of substrates in the aquifers. Hydrogenotrophic methanogenic activity increased with increasing natural gas production from the corresponding wells, suggesting that the flux of substrates from organic-rich mudstones to adjacent sand aquifers is enhanced by the decrease in fluid pressure in sand layers associated with natural gas/water production. The transient predominance of methylotrophic methanogens, observed for a few years after well drilling, also suggested the stimulation of the methanogens by the exposure of unutilized organic matter through well drilling. These results provide an insight into the physicochemical impacts on the methanogenic activity in biogenic gas deposits including marine gas hydrates. PMID:25105906

Ultrasonic rotary-hammer drill

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph (Inventor); Badescu, Mircea (Inventor); Sherrit, Stewart (Inventor); Kassab, Steve (Inventor); Bao, Xiaoqi (Inventor)

2010-01-01

A mechanism for drilling or coring by a combination of sonic hammering and rotation. The drill includes a hammering section with a set of preload weights mounted atop a hammering actuator and an axial passage through the hammering section. In addition, a rotary section includes a motor coupled to a drive shaft that traverses the axial passage through the hammering section. A drill bit is coupled to the drive shaft for drilling by a combination of sonic hammering and rotation. The drill bit includes a fluted shaft leading to a distal crown cutter with teeth. The bit penetrates sampled media by repeated hammering action. In addition, the bit is rotated. As it rotates the fluted bit carries powdered cuttings helically upward along the side of the bit to the surface.

Bentonite deposits of the northern Black Hills district, Wyoming, Montana, and South Dakota

USGS Publications Warehouse

Knechtel, Maxwell M.; Patterson, Sam H.

1962-01-01

The northern Black Hills bentonite mining district includes parts of Crook County, Wyo., Carter County, Mont., and Butte County, S. Dak. Within this district, many beds of bentonite occur interspersed with sedimentary strata of Cretaceous age that have an average total thickness of about 3,000 feet and consist chiefly of marine shale, marl, and argillaceous sandstone. The bentonite beds occur in formations ranging upward from the Newcastle sandstone to the lower part of the Mitten black shale member of the Pierre shale. Tertiary (?) and Quaternary deposits of gravel, sand, and silt are present on extensive terraces, and deposits of such materials also extend along stream courses in all parts of the district. The overall geologic structure of the district is that of a broad northwestward- plunging anticline, in which the strata dip gently toward the northeast, north, and northwest. The overall structure is interrupted, however, by several subordinate folds which bring the bentonite beds to the surface repeatedly, so that large resources of bentonite are present under light overburden. The northern Black Hills district is an important source of commercial gel-forming sodium-type bentonite. During the period 1941-56 more than 5 million tons of raw bentonite was mined, most of which came from the Clay Spur bed near the top of the Mowry shale; a few thousand tons was mined from bed A in the Newcastle sandstone. Calcium-type bentonite occurs in bed B in the Mowry shale and in bed I at the base of the Mitten black shale member. Seven other beds are sufficiently thick and continuous to warrant consideration as prospective sources of bentonite for industrial use. Most of the bentonite produced is sold for use (a) as an ingredient of drilling mud; (b) for preparing metallurgical molding sand of superior dry strength; and (c) for the bonding material used in pelletizing taconite iron ore of the Lake Superior region. The results of drilling-mud and foundry-sand bonding-clay tests of several hundred samples, as well as analyses of selected samples, chiefly by X-ray, differential thermal, base exchange and spectrographic methods, are included in this report.

Neogene Seismic Stratigraphic Framework and Fill History of the Northeastern Albemarle Embayment, North Carolina

NASA Astrophysics Data System (ADS)

Mallinson, D. J.; Riggs, S. R.; Thieler, R.; Culver, S. J.; Corbett, D. R.; Hoffman, C. W.; Wehmiller, J.; Foster, D. S.

2002-12-01

Seismic and chirp sonar surveys were conducted in the eastern Albemarle Sound and adjacent tributaries and the inner continental shelf to define the geologic framework and evolution of the North Carolina coastal system. Surveys were utilized to target paleofluvial channels for drilling and core recovery for the assessment of sea level and climate change during the Quaternary. Lithostratigraphic and chronostratigraphic data are derived from eight drill sites on the Outer Banks, and the Mobil #1 well in the eastern Albemarle Sound. Within the study area, parallel-bedded, gently dipping Miocene beds occur at 100 to >180 mbsl, and are overlain by a southward-thickening Pliocene unit characterized by steeply inclined southward-prograding beds. The Quaternary section unconformably overlies the Pliocene unit, and consists of at least five depositional sequences exhibiting numerous incised channel-fill facies. The Quaternary section is 55 to 60 meters thick. Shallow stratigraphy (0-50 mbsl) is dominated by complex fill-stratigraphy within the incised paleo-Roanoke River valley. Radiocarbon and amino acid racemization (AAR) dates indicate that the valley-fill is late Pleistocene to Holocene in age. At least 6 distinct valley-fill units are identified in the seismic data based upon reflection geometry. Cores reveal a 3 to 6 meter thick basal fluvial channel lag that is overlain by a 15-meter thick unit of interbedded freshwater muds and sands. Organic materials within the freshwater deposits have ages of 13-11 cal. ka, and are overlain by several units comprised of shallow marine sediments. Shallow marine sediments within the valley are silty, fine- to medium-grained sands containing abundant neritic forams, suggesting that this area was an open embayment during much of the Holocene. Seismic data reveal that initial infilling occurred from the north and west during the late Pleistocene and early Holocene. Later infilling occurred from the east and is characterized by a large shoal body (Colington Island and Shoals; radiocarbon dated to 8.6 cal. ka) and adjacent inlet fill. Establishment of a continuous barrier island system resulted in the deposition of a final phase of fill characterized by estuarine organic-rich muds.

30 CFR 250.418 - What additional information must I submit with my APD?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to Drill § 250.418 What additional information must I submit with my APD? You must include the following with the APD: (a) Rated capacities of the drilling rig...

30 CFR 250.418 - What additional information must I submit with my APD?

Code of Federal Regulations, 2014 CFR

2014-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to Drill § 250.418 What additional information must I submit with my APD? You must include the following with the APD: (a) Rated capacities of the drilling rig...

30 CFR 250.418 - What additional information must I submit with my APD?

Code of Federal Regulations, 2013 CFR

2013-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to Drill § 250.418 What additional information must I submit with my APD? You must include the following with the APD: (a) Rated capacities of the drilling rig...

30 CFR 250.418 - What additional information must I submit with my APD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to Drill § 250.418 What additional information must I submit with my APD? You must include the following with the APD: (a) Rated capacities of the drilling rig and major...

Tuffaceous Mud is a Volumetrically Important Volcaniclastic Facies of Submarine Arc Volcanism and Record of Climate Change

NASA Astrophysics Data System (ADS)

Gill, J. B.; Bongiolo, E. M.; Miyazaki, T.; Hamelin, C.; Jutzeler, M.; DeBari, S.; Jonas, A.-S.; Vaglarov, B. S.; Nascimento, L. S.; Yakavonis, M.

2018-04-01

The inorganic portion of tuffaceous mud and mudstone in an oceanic island arc can be mostly volcanic in origin. Consequently, a large volume of submarine volcaniclastic material is as extremely fine-grained as products of subaerial eruptions (<100 µm). Using results of IODP Expedition 350 in the Izu rear arc, we show that such material can accumulate at high rates (12-20 cm/k.y.) within 13 km of the nearest seamount summit and scores of km behind the volcanic front. The geochemistry of bulk, acid-leached mud, and its discrete vitriclasts, shows that >75% of the mud is volcanic, and that most of it was derived from proximal rear arc volcanic sources. It faithfully preserves integrated igneous geochemical information about arc evolution in much the same way that terrigenous shales track the evolution of continental crust. In addition, their high sedimentation rate enables high resolution study of climate cycles, including the effects of Pleistocene glaciation on the behavior of the Kuroshio Current in the Shikoku Basin south of Japan.

Exploring Links Between Global Climate and Explosive Arc Volcanism in Tephra-Rich Quaternary Sediments: A Pilot Study from IODP Expedition 350 Site 1437B, Izu Bonin Rear-Arc Region

NASA Astrophysics Data System (ADS)

Corry-Saavedra, K.; Straub, S. M.; Bolge, L.; Schindlbeck, J. C.; Kutterolf, S.; Woodhead, J. D.

2015-12-01

Fallout tephra in marine sediment provide an excellent archive of explosive arc volcanism that can be directly related to the other parameters of climate change, such as ice volume data, IRD (ice-rafted debris) input, etc. Current studies are based on 'discrete' tephra beds, which are produced by major eruptions and visible with the naked eye. Yet the more common, but less explosive arc eruptions that are more continuous through time produce 'disperse' tephra, which is concealed by the non-volcanic host sediment and invisible to the eye. The proportion of disperse tephra in marine sediments is known to be significant and may be critical in elucidating potential synchronicity between arc volcanism and glacial cycles. We conducted a pilot study in young sediments of IODP Hole 1437B drilled at 31°47.3911'N and 139°01.5788'E at the rear-arc of the Izu Bonin volcanic arc. By means of δ18O (Vautravers, in revision), eleven climatic cycles are recorded in uppermost 120 meter of carbonate mud that is interspersed by cm-thick tephra fallout layers. We selected six tephra layers, ranging from 0.2 to 1.16 million years in age, and sampled those vertically, starting from carbonate mud below the basal contact throughout the typical gradational top into the carbonate mud above. From each tephra bed, volcanic particles (>125 micrometer) were handpicked. All other samples were powdered and leached in buffered acetic acid and hydroxylamine hydrochloride to remove the carbonate and authigenous fraction, respectively. Major and trace element abundances (except for SiO2) from all samples were determined by ICP-MS and ICP-OES methods. Strong binary mixing trends are revealed between the pure tephra end member, and detrital sediment component. The tephra is derived from the Izu Bonin volcanic front and rear-arc, while the sediment component is presumably transported by ocean surface currents from the East China Sea. Our data show that mixing proportions change systematically with sample percentage left after leaching and the stratigraphic position of sample, implying that the composition of the aluminosilicate fraction is an indicator of the percentage of disperse ash present in the carbonate mud. This data leave potential to investigate temporal trends. Our results are currently being refined with radiogenic isotope data.

U.S. Geological survey program on toxic waste--ground-water contamination; proceedings of the Second technical meeting, Cape Cod, Massachusetts, October 21-25, 1985

USGS Publications Warehouse

Ragone, S.E.

1988-01-01

This study characterizes the clay minerals in sediments associated with a plume of creosote-contaminated groundwater. The plume of contaminated groundwater near Pensacola, FL, is in shallow, permeable, Miocene to Holocene quartz sand and flows southward toward Pensacola Bay. Clay-size fractions were separated from 41 cores, chiefly split-spoon samples at 13 drill sites. The most striking feature of the chemical analyses of the clay fractions from uncontaminated site 2 and contaminated sites 4,5,6, and 7 is the variability of iron oxide (species in some samples as Fe2O3); total iron oxide abundance is lowest (2.5%) in uncontaminated sample 2-40, but is > 4.5% (4.5 to 8.5%) in the remaining assemblages. One feature suggesting interaction between the indigenous clays and the waste plume is the presence of nontronite-rich smectite. Nontronite commonly has been identified as the product of hydrothermal alteration and deep-sea weathering of submarine basalts; it is not a common constituent of Cenozoic Gulf Coast sediments. At the Pensacola site, relatively abundant nontronitic smectite is confined to contaminated sands or associated muds; it is least abundant or absent in sands and muds peripheral to the waste plume. The geochemistry of the waste plume, its substantial dissolved, (chiefly ferrous iron), mildly acidic (pH 5-6), and low redox composition, provides an environment similar to that previously determined for the low-temperature synthesis of nontronite. Data from clay-size fractions confirm conclusions that neoformed pyrite in some grain coatings occurs in an assemblage with excess iron over that required in the pyrite. Continuing studies to evaluate these tentative conclusions include: (1) chemical analysis of clay fractions from remaining sites to further examine the apparent relation between iron content and abundance of nontronitic smectite; (2) clay separation and analysis, and pore fluid extraction (squeezing or ultracentrifugation) and analysis from a continuous core through the mud lens to determine pore fluid composition (presence or absence of waste fluid), and character of associated clay minerals; and (3) clay separation and analysis in both permeable sands and the intervening mud lens that are clearly outside the limits of the waste plume to further document the effects of the plume. (See also W90-00022) (Lantz-PTT)

Physical and Chemical Properties of Sintering Red Mud and Bayer Red Mud and the Implications for Beneficial Utilization

PubMed Central

Wang, Ping; Liu, Dong-Yan

2012-01-01

Performances of two common types of red mud, Bayer red mud and Sintering red mud, were investigated in this research. Their compositions, mechanical properties and microstructure characterization were measured through XRD, TG and SEM analysis. Their shear strength, particle size, density and hydraulic characteristics also had been performed. Huge differences between the basic mineral types of these two kinds of red mud also can be found. The comparison of compositions shows that CaCO3 content in Sintering red mud is higher, Bayer red mud has more hazardous elements such as As, Pb and Hg and both have a high concentration of radioactivity. The micro particle of Bayer red mud is finer and more disperse, but the Sintering red mud has higher shear strength. Combining the TG and hydraulic characteristics analysis, it can be shown that Bayer red mud has higher value of water content and Sintering red mud has higher hydraulic conductivity. The paper then illustrates that Sintering red mud can become the main filling material of supporting structure of red mud stocking yard. Bayer red mud has a high reuse value and also can be used as a mixing material of masonry mortar.

Time-dependent source model of the Lusi mud volcano

NASA Astrophysics Data System (ADS)

Shirzaei, M.; Rudolph, M. L.; Manga, M.

2014-12-01

The Lusi mud eruption, near Sidoarjo, East Java, Indonesia, began erupting in May 2006 and continues to erupt today. Previous analyses of surface deformation data suggested an exponential decay of the pressure in the mud source, but did not constrain the geometry and evolution of the source(s) from which the erupting mud and fluids ascend. To understand the spatiotemporal evolution of the mud and fluid sources, we apply a time-dependent inversion scheme to a densely populated InSAR time series of the surface deformation at Lusi. The SAR data set includes 50 images acquired on 3 overlapping tracks of the ALOS L-band satellite between May 2006 and April 2011. Following multitemporal analysis of this data set, the obtained surface deformation time series is inverted in a time-dependent framework to solve for the volume changes of distributed point sources in the subsurface. The volume change distribution resulting from this modeling scheme shows two zones of high volume change underneath Lusi at 0.5-1.5 km and 4-5.5km depth as well as another shallow zone, 7 km to the west of Lusi and underneath the Wunut gas field. The cumulative volume change within the shallow source beneath Lusi is ~2-4 times larger than that of the deep source, whilst the ratio of the Lusi shallow source volume change to that of Wunut gas field is ~1. This observation and model suggest that the Lusi shallow source played a key role in eruption process and mud supply, but that additional fluids do ascend from depths >4 km on eruptive timescales.

Radial modes of laterally stiffened piezoelectric disc transducers for ultrasonic collimated beam generation

DOE PAGES

Chillara, Vamshi Krishna; Pantea, Cristian; Sinha, Dipen N.

2017-07-15

Here, we numerically investigate the resonance and vibration characteristics of radial modes of laterally stiffened piezoelectric disc transducers. Lateral stiffening is modeled using a spring and vibration characteristics of the piezo-disc are investigated with increasing lateral stiffness. It is found that the resonant frequency response of the radial modes follows an asymptotic behavior approaching that of a clamped disc with increasing lateral stiffness. The radial mode vibration pattern of the discs is also found to be affected by lateral stiffness. While the vibration pattern of a free disc corresponds to a Bessel function, laterally stiffened discs show edge-effects where theymore » depart from the Bessel-like behavior. In addition, a fully clamped piezo-disc is found to have an extra side-lobe when compared to a free disc. Ultrasonic beam profiles generated from radial modes of laterally stiffened discs are numerically investigated. It is found that the free piezo-disc generates a Bessel beam that has multiple side-lobes. Increasing the lateral stiffness results in a significant reduction of side-lobes in the beam profile. This technique of generating a collimated beam with side-lobe reduction finds significant applications in imaging through concrete, drilling mud, and other highly attenuating materials.« less

Impact to Underground Sources of Drinking Water and Domestic Wells from Production Well Stimulation and Completion Practices in the Pavillion, Wyoming, Field.

PubMed

DiGiulio, Dominic C; Jackson, Robert B

2016-04-19

A comprehensive analysis of all publicly available data and reports was conducted to evaluate impact to Underground Sources of Drinking Water (USDWs) as a result of acid stimulation and hydraulic fracturing in the Pavillion, WY, Field. Although injection of stimulation fluids into USDWs in the Pavillion Field was documented by EPA, potential impact to USDWs at the depths of stimulation as a result of this activity was not previously evaluated. Concentrations of major ions in produced water samples outside expected levels in the Wind River Formation, leakoff of stimulation fluids into formation media, and likely loss of zonal isolation during stimulation at several production wells, indicates that impact to USDWs has occurred. Detection of organic compounds used for well stimulation in samples from two monitoring wells installed by EPA, plus anomalies in major ion concentrations in water from one of these monitoring wells, provide additional evidence of impact to USDWs and indicate upward solute migration to depths of current groundwater use. Detections of diesel range organics and other organic compounds in domestic wells <600 m from unlined pits used prior to the mid-1990s to dispose diesel-fuel based drilling mud and production fluids suggest impact to domestic wells as a result of legacy pit disposal practices.

Characterization of clay scales forming in Philippine geothermal wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reyes, A.G.; Cardile, C.M.

1989-01-01

Smectite scales occur in 24 out of the 36 blocked wells located in Tongonan, Palinpinon and Bacon-Manito. These comprise 2-85% of the well scales and form at depths of 33-2620 m, where measured and fluid inclusion temperatures are 40-320{sup 0}C. Most, however, occur below the production casing show where temperatures are {ge}230{sup 0}C, often at depths coinciding with aquifers. The clay scales are compositionally and structurally different from the bentonite used in drilling, which is essentially sodium-rich montmorillonite. The clay deposits are expanding, generally disordered, and combine the characteristics of a montmorillonite, saponite and vermiculite in terms of reaction tomore » cationic exchange treatments, structure and composition. Six types of clay scales are identified, but the predominant one, comprising 60-100% of the clay deposits in a well, is Mg- and Fe-rich and referred to as a vermiculitic species. The crystallinity, degree of disorder, textures, optical characteristics, structure and relative amounts of structural Al, Mg and Fe vary with time, temperature and fluid composition, but not with depth and measured pressure. Despite its variance from bentonite characteristics, one of the dominant suggested mechanisms of clay scale formation uses the drilling mud in the well as a substrate, from which the Mg- and Fe-rich clay evolves.« less

Scientific basis for safely shutting in the Macondo Well after the April 20, 2010 Deepwater Horizon blowout

USGS Publications Warehouse

Hickman, Stephen H.; Hsieh, Paul A.; Mooney, Walter D.; Enomoto, Catherine B.; Nelson, Philip H.; Flemings, Peter; Mayer, Larry; Moran, Kathryn; Weber, Thomas; McNutt, Marcia K.; Rice, James R.

2012-01-01

As part of the government response to the Deepwater Horizon blowout, a Well Integrity Team evaluated the geologic hazards of shutting in the Macondo Well at the seafloor and determined the conditions under which it could safely be undertaken. Of particular concern was the possibility that, under the anticipated high shut-in pressures, oil could leak out of the well casing below the seafloor. Such a leak could lead to new geologic pathways for hydrocarbon release to the Gulf of Mexico. Evaluating this hazard required analyses of 2D and 3D seismic surveys, seafloor bathymetry, sediment properties, geophysical well logs, and drilling data to assess the geological, hydrological, and geomechanical conditions around the Macondo Well. After the well was successfully capped and shut in on July 15, 2010, a variety of monitoring activities were used to assess subsurface well integrity. These activities included acquisition of wellhead pressure data, marine multichannel seismic profiles, seafloor and water-column sonar surveys, and wellhead visual/acoustic monitoring. These data showed that the Macondo Well was not leaking after shut in, and therefore, it could remain safely shut until reservoir pressures were suppressed (killed) with heavy drilling mud and the well was sealed with cement.

Intraterrestrial life in igneous ocean crust: advances, technologies, and the future (Invited)

NASA Astrophysics Data System (ADS)

Edwards, K. J.; Wheat, C. G.

2010-12-01

The “next frontier” of scientific investigation in the deep sub-seafloor microbial biosphere lies in a realm that has been a completely unexplored until just the past decade: the igneous oceanic crust. Problems that have hampered exploration of the “hard rock” marine deep biosphere have revolved around sample access (hard rock drilling is technologically complex), contamination (a major hurdle), momentum (why take on this challenge when the relatively “easier” marine muds also have been a frontier) and suspicion that microbes in more readily accessed using (simpler) non-drilling technologies - like vents - are truly are endemic of subsurface clades/activities. Since the late 1990’s, however, technologies and resultant studies on microbes in the igneous ocean crust deep biosphere have risen sharply, and offer a new and distinct view on this biome. Moreover, microbiologists are now taking leading roles in technological developments that are critically required to address this biosphere - interfacing and collaborating closely with engineers, genomic biologists, geologists, seismologists, and geochemists to accomplish logistically complex and long-term studies that bring observatory research to this deep realm. The future of this field for the least decade is rich - opportunities abound for microbiologists to play new roles in how we study microbiology in the deep subsurface in an oceanographic and Earth system science perspective.

Energy Return On Investment of Engineered Geothermal Systems Data

DOE Data Explorer

Mansure, Chip

2012-01-01

The project provides an updated Energy Return on Investment (EROI) for Enhanced Geothermal Systems (EGS). Results incorporate Argonne National Laboratory's Life Cycle Assessment and base case assumptions consistent with other projects in the Analysis subprogram. EROI is a ratio of the energy delivered to the consumer to the energy consumed to build, operate, and decommission the facility. EROI is important in assessing the viability of energy alternatives. Currently EROI analyses of geothermal energy are either out-of-date, of uncertain methodology, or presented online with little supporting documentation. This data set is a collection of files documenting data used to calculate the Energy Return On Investment (EROI) of Engineered Geothermal Systems (EGS) and erratum to publications prior to the final report. Final report is available from the OSTI web site (http://www.osti.gov/geothermal/). Data in this collections includes the well designs used, input parameters for GETEM, a discussion of the energy needed to haul materials to the drill site, the baseline mud program, and a summary of the energy needed to drill each of the well designs. EROI is the ratio of the energy delivered to the customer to the energy consumed to construct, operate, and decommission the facility. Whereas efficiency is the ratio of the energy delivered to the customer to the energy extracted from the reservoir.

Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 544: Cellars, Mud Pits, and Oil Spills, Nevada Test Site, Nevada, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark Krauss

2010-07-01

This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 544, Cellars, Mud Pits, and Oil Spills, identified in the Federal Facility Agreement and Consent Order (FFACO). Corrective Action Unit 544 comprises the following 20 corrective action sites (CASs) located in Areas 2, 7, 9, 10, 12, 19, and 20 of the Nevada Test Site (NTS): • 02-37-08, Cellar & Mud Pit • 02-37-09, Cellar & Mud Pit • 07-09-01, Mud Pit • 09-09-46, U-9itsx20 PS #1A Mud Pit • 10-09-01, Mud Pit • 12-09-03, Mud Pit • 19-09-01, Mudmore » Pits (2) • 19-09-03, Mud Pit • 19-09-04, Mud Pit • 19-25-01, Oil Spill • 19-99-06, Waste Spill • 20-09-01, Mud Pits (2) • 20-09-02, Mud Pit • 20-09-03, Mud Pit • 20-09-04, Mud Pits (2) • 20-09-06, Mud Pit • 20-09-07, Mud Pit • 20-09-10, Mud Pit • 20-25-04, Oil Spills • 20-25-05, Oil Spills This plan provides the methodology for field activities needed to gather the necessary information for closing each CAS. There is sufficient information and process knowledge from historical documentation and investigations of similar sites regarding the expected nature and extent of potential contaminants to recommend closure of CAU 544 using the SAFER process. Using the approach approved for previous mud pit investigations (CAUs 530–535), 14 mud pits have been identified that • are either a single mud pit or a system of mud pits, • are not located in a radiologically posted area, and • have no evident biasing factors based on visual inspections. These 14 mud pits are recommended for no further action (NFA), and further field investigations will not be conducted. For the sites that do not meet the previously approved closure criteria, additional information will be obtained by conducting a field investigation before selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible recommendation for closure of the remaining CASs in CAU 544. This will be presented in a closure report (CR) that will be prepared and submitted to the Nevada Division of Environmental Protection (NDEP) for review and approval. The sites will be investigated based on the data quality objectives (DQOs) developed on April 27, 2010, by representatives of NDEP and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO). The DQO process was used to identify and define the type, amount, and quality of data needed to determine and implement appropriate corrective actions for each CAS in CAU 544. The DQO process developed for this CAU identified the following expected closure options: (1) investigation and confirmation that no contamination exists above the final action levels (FALs) leading to an NFA declaration, (2) characterization of the nature and extent of contamination leading to closure in place with use restrictions, (3) clean closure by remediation and verification, (4) closure in place with use restrictions with no investigation if CASs are in crater areas that have been determined to be unsafe to enter, or (5) NFA if the mud pit CAS meets the criteria established during the CAUs 530–535 SAFER investigation. The following summarizes the SAFER activities that will support the closure of CAU 544: • Perform visual inspection of all CASs. • Perform site preparation activities (e.g., utilities clearances, construction of temporary site exclusion zones). • Removal of easily managed, nonhazardous, and nonradioactive debris, including vegetation (e.g., tumbleweeds), at various CASs that interfere with sampling, if required to inspect soil surface or collect soil sample. • Collect environmental samples from designated target populations (e.g., mud pits, cellars, stained soil) to confirm or disprove the presence of contaminants of concern (COCs) as necessary to supplement existing information. • If no COCs are present at a CAS, establish NFA as the corrective action. • If COCs exist, collect environmental samples from designated target populations (e.g., clean soil adjacent to contaminated soil) and submit for laboratory analyses to define the extent of COC contamination. • If a COC is present at a CAS, either - Establish clean closure as the corrective action. The material to be remediated will be removed, disposed of as waste, and verification samples will be collected from remaining soil, or - Establish closure in place as the corrective action and implement the appropriate use restrictions. • Confirm the preferred closure option is sufficient to protect human health and the environment.« less

Increasing arsenic sorption on red mud by phosphogypsum addition.

PubMed

Lopes, G; Guilherme, L R G; Costa, E T S; Curi, N; Penha, H G V

2013-11-15

Mining by-products have been tested as adsorbents for arsenic in order to reduce As bioavailability. This study evaluated a red mud (RM) treated with or without phosphogypsum (G) in order to improve its As retention. Red mud and G samples and their mixtures were chemically and mineralogically characterized to gather information concerning their composition, which is key for a better understanding of the adsorbent properties. Phosphogypsum was added to RM in the following proportions: 0, 1, 2, 5, 10, and 25% by weight. These mixtures were subjected to As adsorption and desorption and tested for their maximum adsorption capacity of As (AsMAC). Arsenic adsorption increased upon increasing the proportion of G added to RM. The AsMAC at pure RM reached 909 mg kg(-1), whereas the 75%-RM+25%-G mixture sorbed up to 3333 mg kg(-1) of As, i.e., a 3.5-fold increase in AsMAC. Using G in mixtures with RM increases the efficiency of As adsorption due to the presence of Ca(2+), which alters the charge balance of the adsorbent, leading to the formation of ternary complexes. Addition of G to RM is thus a promising technique to improve As retention, while providing additional value to both by-products, G and RM. Copyright © 2012 Elsevier B.V. All rights reserved.

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2014 CFR

2014-07-01

... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take...

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow...

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2013 CFR

2013-07-01

... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take...

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2012 CFR

2012-07-01

... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take...

Linking downhole logging data with geology and drilling /coring operations - Example from Chicxulub Expedition 364.

NASA Astrophysics Data System (ADS)

Lofi, Johanna; Smith, Dave; Delahunty, Chris; Le Ber, Erwan; Mellet, Claire; Brun, Laurent; Henry, Gilles; Paris, Jehanne

2017-04-01

Expedition 364 was a joint IODP/ICDP mission specific platform expedition to explore the Chicxulub impact crater buried below the Yucatán continental shelf. In April and May 2016, our Expedition drilled a single borehole at Site M0077A into the crater's peak ring. It allowed recovering 303 excellent quality cores from 505.7 to 1334.7 meters below sea floor and acquiring more than 5.8 km of high resolution open hole logs. Downhole logs are rapidly collected, continuous with depth, and measured in situ; these data are classically interpreted in terms of stratigraphy, lithology, porosity, fluid content, geochemical composition and structure of the formation drilled. Downhole logs also allow assessing borehole quality (eg. shape and trajectory), and can provide assistance for decision support during drilling operations. In this work, Expedition 364 downhole logs are used to improve our understanding of the drilling/coring operation history. Differentiating between natural geological features and borehole artifacts are also critical for data quality assessment. The set of downhole geophysical tools used during Expedition 364 was constrained by the scientific objectives, drilling/coring technique, hole conditions and temperature at the drill site. Wireline logging data were acquired with slimline tools in three logging phases at intervals 0-503, 506-699 and 700-1334 mbsf. Logs were recorded either with standalone logging tools or, for the first time in IODP, with stackable slimline tools. Log data included total gamma radiation, sonic velocity, acoustic and optical borehole images, resistivity, conductivity, magnetic susceptibility, caliper and borehole fluid parameters. The majority of measurements were performed in open borehole conditions. During the drilling operations some problems were encountered directly linked to the geology of the drilled formation. For example, two zones of mud circulation losses correlate in depth with the presence of karst cavities or open faults, as evidenced from borehole wall images. Both form conduits probably open at a large scale as suggested by associated anomalies in the borehole fluid temperature profiles. When coring the basement, pieces of metal trapped outside the drill bit apparently led to an increase of the borehole tilt as well as to an enlargement of the hole, although this later remained sub-circular. In the post impact carbonates, 6-7 m long apparent cyclic oscillations in the magnetic field coupled to a spiral shape trajectory of the same wavelength suggest drilling induced artifacts and formation re-magnetization. Acknowledgements: Expedition 364 was funded by IODP with co-funding from ICDP and implemented by ECORD, with contributions and logistical support from the Yucatán state government and Universidad Nacional Autónoma de México. Drilling Services were provided by DOSECC Exploration Services. The downhole logging program was coordinated by EPC, as part of ESO. Expedition 364 Scientists: S. Gulick, J.V. Morgan, E. Chenot, G. Christeson, P. Claeys, C. Cockell, M.J. L. Coolen, L. Ferrière, C. Gebhardt, K. Goto, H. Jones, D.A. Kring, J. Lofi, X. Long, C. Lowery, C. Mellett, R. Ocampo-Torres, L. Perez-Cruz, A. Pickersgill, M. Poelchau, A. Rae, C. Rasmussen, M. Rebolledo-Vieyra, U. Riller, H. Sato, J. Smit, S. Tikoo, N. Tomioka, M. Whalen, A. Wittmann, J. Urrutia-Fucugauchi, K.E. Yamaguchi, W. Zylberman.

Assessment of contamination by percolation of septic tank effluent through natural and amended soils.

PubMed

Cheung, K C; Venkitachalam, T H

2004-01-01

Fly ash has been found to be a potential material for the treatment of municipal and industrial wastewater, and may be useful in the treatment of septic tank effluent. Laboratory columns (30 cm) were used to determine the sorption capacity and hydraulic properties of lagoon fly ash, loamy sand, sand, and sand amended by lagoon fly ash (30 and 60%) and red mud gypsum (20%). The removal of chemical oxygen demand (COD) was high in all column effluents (71-93%). Extent of nitrification was high in Spearwood sand, Merribrook loamy sand and 20% red mud gypsum amended Spearwood sand. However, actual removal of nitrogen (N) was high in columns containing lagoon fly ash. Unamended Spearwood sand possessed only minimal capacity for P sorption. Merribrook loamy sand and red mud gypsum amended sand affected complete P removal throughout the study period of 12 weeks. Significant P leakage occurred from lagoon fly ash amended sand columns following 6-10 weeks of operation. Neither lagoon fly ash nor red mud gypsum caused any studied heavy metal contamination including manganese (Mn), lead (Pb), zinc (Zn), cadmium (Cd) and chromium (Cr) of effluent. It can be concluded that Merribrook loamy sand is better natural soil than Spearwood sand as a filter medium. The addition of lagoon fly ash enhanced the removal of P in Spearwood sand but the efficiency was lower than with red mud gypsum amendment.

Characterization of the putative iron sulfur protein IdiC (ORF5) in Synechococcus elongatus PCC 7942.

PubMed

Pietsch, Daniel; Staiger, Dorothee; Pistorius, Elfriede K; Michel, Klaus-Peter

2007-10-01

The IdiC protein (iron deficiency induced protein C) is encoded by orf5 (now called idiC), which is part of the iron-responsive idiB operon of Synechococcus elongatus PCC 7942. The 20.5 kDa IdiC protein has a putative transmembrane helix and belongs to the thioredoxin (TRX)-like [2Fe-2S] ferredoxin family. IdiC has the highest similarity to the peripheral subunit NuoE of the Escherichia coli NDH-1 complex. IdiC expression increased under iron starvation and also in the late growth phase, representing growth conditions, which favor photosynthetic cyclic and respiratory electron transport over photosynthetic linear electron transport from water to NADP+. Attempts to insertionally inactivate the idiC gene generated merodiploid mutants with a strongly reduced IdiC content (mutant MuD) but no IdiC-free mutant. Thus, IdiC seems to be an essential protein for the viability of S. elongatus under the used experimental conditions. Comparative analyses of S. elongatus wild type (WT) and mutant MuD showed that under iron limitation in WT and MuD the amount of the reaction center proteins PsbA and PsaA/B was highly reduced. MuD had a lower growth rate, chlorophyll content, and photosynthetic O2 evolving activity with bicarbonate as electron acceptor than WT. Immunoblot analyses also showed that in MuD, when grown under iron limitation, the amount of the proteins IdiC and IdiB was greatly reduced as compared to WT. As a consequence of the reduction of the transcription factor IdiB, IdiA and IrpA expression were also decreased. In addition, the IsiA protein concentration was lower in MuD than in WT, although the isiA mRNA was equally high in MuD and WT. Another significant difference was the lower expression of the ferredoxin:NADP+ oxidoreductase in mutant MuD under iron limitation compared to WT. A possible function of the protein IdiC in cyclic electron transport around photosystem I and/or in respiratory electron transport will be discussed.

Textures of water-rich mud sediments from the continental margin offshore Costa Rica (IODP expeditions 334 and 344)

NASA Astrophysics Data System (ADS)

Kuehn, Rebecca; Stipp, Michael; Leiss, Bernd

2017-04-01

During sedimentation and burial at continental margins, clay-rich sediments develop crystallographic preferred orientations (textures) depending on the ongoing compaction as well as size distribution and shape fabrics of the grains. Such textures can control the deformational properties of these sediments and hence the strain distribution in active continental margins and also the frictional behavior along and around the plate boundary. Strain-hardening and discontinuous deformation may lead to earthquake nucleation at or below the updip limit of the seismogenic zone. We want to investigate the active continental margin offshore Costa Rica where the oceanic Cocos plate is subducted below the Caribbean plate at a rate of approximately 9 cm per year. The Costa Rica trench is well-known for shallow seismogenesis and tsunami generation. As it is an erosive continental margin, both the incoming sediments from the Nazca plate as well as the slope sediments of the continental margin can be important for earthquake nucleation and faulting causing sea-floor breakage. To investigate texture and composition of the sediments and hence their deformational properties we collected samples from varying depth of 7 different drilling locations across the trench retrieved during IODP expeditions 334 and 344 as part of the Costa Rica Seismogenesis Project (CRISP). Texture analysis was carried out by means of synchrotron diffraction, as only this method is suitable for water-bearing samples. As knowledge on the sediment composition is required as input parameter for the texture data analysis, additional X-ray powder diffraction analysis on the sample material has been carried out. Samples for texture measurements were prepared from the original drill cores using an internally developed cutter which allows to produce cylindrical samples with a diameter of about 1.5 cm. The samples are oriented with respect to the drill core axis. Synchrotron texture measurements were conducted at the ESRF (European Synchrotron Radiation Facility) in Grenoble and the DESY (German Electron Synchrotron) in Hamburg. Samples were measured in transmission mode perpendicular to their cylinder axis with a beam diameter of 500 µm. Measurements were taken from 0 to 175° in 5° steps resulting in 36 images from a 2D image plate detector. Measurement time was in a range from 1 to 3 seconds. Due to the different, low symmetric mineral phases a large number of mostly overlapping reflections results. Such data can only be analyzed by the Rietveld method, in our case implemented in the software package MAUD (Materials Analysis Using Diffraction). Preliminary results show distinct textures depending on the composition and the origin of the samples, i.e. on drilling location and depth, which may be critical for strain localization and faulting of these samples. The results are also important for the analysis of experimentally deformed samples from the same drill cores which showed structurally weak and structurally strong deformation behavior during triaxial compression.

P-wave velocity model of mud volcano on the continental slope of the Canadian Beaufort Sea from frequency-domain full waveform inversion

NASA Astrophysics Data System (ADS)

Jang, U. G.; Kang, S. G.; Hong, J. K.; Jin, Y. K.; Dallimore, S.; Riedel, M.; Paull, C. K.

2017-12-01

2014 Expedition ARA05C was a multidisciplinary undertaking conducted in the Canadian Beaufort Sea, Arctic Ocean on the Korean ice breaker IBRV ARAON from August 30 to September 19, 2014. The program was carried out as collaboration between the Korea Polar Research Institute (KOPRI), Geological Survey of Canada (GSC), Monterey Bay Aquarium Research Institute (MBARI), Department of Fisheries and Ocean (DFO) with participation by Bremen University (BARUM). During this expedition, multi-channel seismic (MCS) data were acquired on the outer continental shelf and upper slope of the Canadian Beaufort Sea, totaling 20 lines with 1,000 line-kilometers from September 1 to September 13, 2014. Three MCS survey lines was designed to cross the three submarine mud volcanoes found in the slope at approximate water depth of 290 m, 460 m and 740 m. Submarine mud volcanoes are seafloor structures with positive topography formed by a combination of mud eruption, gas emission, and water seepage from the subsurface. MCS data will allow image subsurface structures of mud volcanoes as identification of fluid migration pathways, however, imaging its subsurface structure is difficult by using conventional seismic data processing procedure, because it is seismically characterized by acoustically transparent facies. Full waveform inversion (FWI) is non-linear data-fitting procedure to estimate the physical properties of the subsurface by minimizing the difference between the observed and modelled data. FWI uses the two-wave wave equation to compute forward/backward wavefield to calculate the gradient direction, therefore it can derive more detailed velocity model beyond travel-time tomography techniques, which use only the kinematics of seismic data, by additional information provided by the amplitude and phase of the seismic waveform. In this study, we suggest P-wave structure of mud volcanos, which were inverted by 2D acoustic FWI. It will be useful to understand the characterization of mud volcanoes on the slope of Canadian Beaufort Sea.

Isoform-specific functions of Mud/NuMA mediate binucleation of Drosophila male accessory gland cells.

PubMed

Taniguchi, Kiichiro; Kokuryo, Akihiko; Imano, Takao; Minami, Ryunosuke; Nakagoshi, Hideki; Adachi-Yamada, Takashi

2014-12-20

In standard cell division, the cells undergo karyokinesis and then cytokinesis. Some cells, however, such as cardiomyocytes and hepatocytes, can produce binucleate cells by going through mitosis without cytokinesis. This cytokinesis skipping is thought to be due to the inhibition of cytokinesis machinery such as the central spindle or the contractile ring, but the mechanisms regulating it are unclear. We investigated them by characterizing the binucleation event during development of the Drosophila male accessory gland, in which all cells are binucleate. The accessory gland cells arrested the cell cycle at 50 hours after puparium formation (APF) and in the middle of the pupal stage stopped proliferating for 5 hours. They then restarted the cell cycle and at 55 hours APF entered the M-phase synchronously. At this stage, accessory gland cells binucleated by mitosis without cytokinesis. Binucleating cells displayed the standard karyokinesis progression but also showed unusual features such as a non-round shape, spindle orientation along the apico-basal axis, and poor assembly of the central spindle. Mud, a Drosophila homolog of NuMA, regulated the processes responsible for these three features, the classical isoform Mud(PBD) and the two newly characterized isoforms Mud(L) and Mud(S) regulated them differently: Mud(L) repressed cell rounding, Mud(PBD) and Mud(S) oriented the spindle along the apico-basal axis, and Mud(S) and Mud(L) repressed central spindle assembly. Importantly, overexpression of Mud(S) induced binucleation even in standard proliferating cells such as those in imaginal discs. We characterized the binucleation in the Drosophila male accessory gland and examined mechanisms that regulated unusual morphologies of binucleating cells. We demonstrated that Mud, a microtubule binding protein regulating spindle orientation, was involved in this binucleation. We suggest that atypical functions exerted by three structurally different isoforms of Mud regulate cell rounding, spindle orientation and central spindle assembly in binucleation. We also propose that Mud(S) is a key regulator triggering cytokinesis skipping in binucleation processes.

Vertical Flume Testing of WIPP Surrogate Waste Materials

NASA Astrophysics Data System (ADS)

Herrick, C. G.; Schuhen, M.; Kicker, D.

2012-12-01

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy geological repository for the permanent disposal of defense-related transuranic (TRU) waste. The waste is emplaced in rooms excavated in the bedded Salado salt formation at a depth of 655 m below ground surface. After emplacement of the waste, the repository will be sealed and decommissioned. The DOE demonstrates compliance with 40 CFR 194 by means of performance assessment (PA) calculations conducted by Sandia National Laboratories. WIPP PA calculations estimate the probability and consequences of radionuclide releases for a 10,000 year regulatory period. Human intrusion scenarios include cases in which a future borehole is drilled through the repository. Drilling mud flowing up the borehole will apply a hydrodynamic shear stress to the borehole wall which could result in erosion of the waste and radionuclides being carried up the borehole. WIPP PA uses the parameter TAUFAIL to represent the shear strength of the degraded waste. The hydrodynamic shear strength can only be measured experimentally by flume testing. Flume testing is typically performed horizontally, mimicking stream or ocean currents. However, in a WIPP intrusion event, the drill bit would penetrate the degraded waste and drilling mud would flow up the borehole in a predominantly vertical direction. In order to simulate this, a flume was designed and built so that the eroding fluid enters an enclosed vertical channel from the bottom and flows up past a specimen of surrogate waste material. The sample is pushed into the current by a piston attached to a step motor. A qualified data acquisition system controls and monitors the fluid's flow rate, temperature, pressure, and conductivity and the step motor's operation. The surrogate materials used correspond to a conservative estimate of degraded TRU waste at the end of the regulatory period. The recipes were previously developed by SNL based on anticipated future states of the waste considering inventory, changes in the underground environment, and theoretical and experimental results. The recipes represent the degraded waste in its weakest condition; simulating 50, 75, and 100% degradation by weight. The percent degradation indicates the anticipated amount of iron corrosion and decomposition of cellulosics, plastics, and rubbers. Samples were die compacted to two pressures, 2.3 and 5.0 MPa. Testing has established that the less degraded the surrogate material is and the higher the compaction stress it undergoes, the stronger the sample is. The 50% degraded surrogate waste material was accepted for use in obtaining input parameters for another WIPP PA model by a conceptual model peer review panel and the EPA. The use of a 50% degraded surrogate waste in vertical flume testing would provide an improved estimate of the waste shear strength and establish consistency between PA models in the approach used to obtain input parameters. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. This research is funded by WIPP programs administered by the Office of Environmental Management (EM) of the U.S Department of Energy.

Vertical Flume Testing of WIPP Surrogate Waste Materials

NASA Astrophysics Data System (ADS)

Herrick, C. G.; Schuhen, M.; Kicker, D.

2013-12-01

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy geological repository for the permanent disposal of defense-related transuranic (TRU) waste. The waste is emplaced in rooms excavated in the bedded Salado salt formation at a depth of 655 m below ground surface. After emplacement of the waste, the repository will be sealed and decommissioned. The DOE demonstrates compliance with 40 CFR 194 by means of performance assessment (PA) calculations conducted by Sandia National Laboratories. WIPP PA calculations estimate the probability and consequences of radionuclide releases for a 10,000 year regulatory period. Human intrusion scenarios include cases in which a future borehole is drilled through the repository. Drilling mud flowing up the borehole will apply a hydrodynamic shear stress to the borehole wall which could result in erosion of the waste and radionuclides being carried up the borehole. WIPP PA uses the parameter TAUFAIL to represent the shear strength of the degraded waste. The hydrodynamic shear strength can only be measured experimentally by flume testing. Flume testing is typically performed horizontally, mimicking stream or ocean currents. However, in a WIPP intrusion event, the drill bit would penetrate the degraded waste and drilling mud would flow up the borehole in a predominantly vertical direction. In order to simulate this, a flume was designed and built so that the eroding fluid enters an enclosed vertical channel from the bottom and flows up past a specimen of surrogate waste material. The sample is pushed into the current by a piston attached to a step motor. A qualified data acquisition system controls and monitors the fluid's flow rate, temperature, pressure, and conductivity and the step motor's operation. The surrogate materials used correspond to a conservative estimate of degraded TRU waste at the end of the regulatory period. The recipes were previously developed by SNL based on anticipated future states of the waste considering inventory, changes in the underground environment, and theoretical and experimental results. The recipes represent the degraded waste in its weakest condition; simulating 50, 75, and 100% degradation by weight. The percent degradation indicates the anticipated amount of iron corrosion and decomposition of cellulosics, plastics, and rubbers. Samples were die compacted to two pressures, 2.3 and 5.0 MPa. Testing has established that the less degraded the surrogate material is and the higher the compaction stress it undergoes, the stronger the sample is. The 50% degraded surrogate waste material was accepted for use in obtaining input parameters for another WIPP PA model by a conceptual model peer review panel and the EPA. The use of a 50% degraded surrogate waste in vertical flume testing would provide an improved estimate of the waste shear strength and establish consistency between PA models in the approach used to obtain input parameters. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. This research is funded by WIPP programs administered by the Office of Environmental Management (EM) of the U.S Department of Energy.

High Temperature 300°C Directional Drilling System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chatterjee, Kamalesh; Aaron, Dick; Macpherson, John

2015-07-31

Many countries around the world, including the USA, have untapped geothermal energy potential. Enhanced Geothermal Systems (EGS) technology is needed to economically utilize this resource. Temperatures in some EGS reservoirs can exceed 300°C. To effectively utilize EGS resources, an array of injector and production wells must be accurately placed in the formation fracture network. This requires a high temperature directional drilling system. Most commercial services for directional drilling systems are rated for 175°C while geothermal wells require operation at much higher temperatures. Two U.S. Department of Energy (DOE) Geothermal Technologies Program (GTP) projects have been initiated to develop a 300°Cmore » capable directional drilling system, the first developing a drill bit, directional motor, and drilling fluid, and the second adding navigation and telemetry systems. This report is for the first project, “High Temperature 300°C Directional Drilling System, including drill bit, directional motor and drilling fluid, for enhanced geothermal systems,” award number DE-EE0002782. The drilling system consists of a drill bit, a directional motor, and drilling fluid. The DOE deliverables are three prototype drilling systems. We have developed three drilling motors; we have developed four roller-cone and five Kymera® bits; and finally, we have developed a 300°C stable drilling fluid, along with a lubricant additive for the metal-to-metal motor. Metal-to-metal directional motors require coatings to the rotor and stator for wear and corrosion resistance, and this coating research has been a significant part of the project. The drill bits performed well in the drill bit simulator test, and the complete drilling system has been tested drilling granite at Baker Hughes’ Experimental Test Facility in Oklahoma. The metal-to-metal motor was additionally subjected to a flow loop test in Baker Hughes’ Celle Technology Center in Germany, where it ran for more than 100 hours.« less

Chemo-Mechanical Characteristics of Mud Formed from Environmental Dust Particles in Humid Ambient Air

PubMed Central

Hassan, Ghassan; Yilbas, B. S.; Said, Syed A. M.; Al-Aqeeli, N.; Matin, Asif

2016-01-01

Mud formed from environmental dust particles in humid ambient air significantly influences the performance of solar harvesting devices. This study examines the characterization of environmental dust particles and the chemo-mechanics of dry mud formed from dust particles. Analytical tools, including scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, particle sizing, and X-ray diffraction, are used to characterize dry mud and dust particles. A micro/nano tribometer is used to measure the tangential force and friction coefficient while tensile tests are carried out to assess the binding forces of dry mud pellets. After dry mud is removed, mud residuals on the glass surface are examined and the optical transmittance of the glass is measured. Dust particles include alkaline compounds, which dissolve in water condensate and form a mud solution with high pH (pH = 7.5). The mud solution forms a thin liquid film at the interface of dust particles and surface. Crystals form as the mud solution dries, thus, increasing the adhesion work required to remove dry mud from the surface. Optical transmittance of the glass is reduced after dry mud is removed due to the dry mud residue on the surface. PMID:27445272

Chemo-Mechanical Characteristics of Mud Formed from Environmental Dust Particles in Humid Ambient Air.

PubMed

Hassan, Ghassan; Yilbas, B S; Said, Syed A M; Al-Aqeeli, N; Matin, Asif

2016-07-22

Mud formed from environmental dust particles in humid ambient air significantly influences the performance of solar harvesting devices. This study examines the characterization of environmental dust particles and the chemo-mechanics of dry mud formed from dust particles. Analytical tools, including scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, particle sizing, and X-ray diffraction, are used to characterize dry mud and dust particles. A micro/nano tribometer is used to measure the tangential force and friction coefficient while tensile tests are carried out to assess the binding forces of dry mud pellets. After dry mud is removed, mud residuals on the glass surface are examined and the optical transmittance of the glass is measured. Dust particles include alkaline compounds, which dissolve in water condensate and form a mud solution with high pH (pH = 7.5). The mud solution forms a thin liquid film at the interface of dust particles and surface. Crystals form as the mud solution dries, thus, increasing the adhesion work required to remove dry mud from the surface. Optical transmittance of the glass is reduced after dry mud is removed due to the dry mud residue on the surface.

Soil gas anomalies along the Watukosek fault system, East Java, Indonesia

NASA Astrophysics Data System (ADS)

Sciarra, A.; Ruggiero, L.; Bigi, S.; Mazzini, A.

2017-12-01

Two soil gas surveys were carried out in the Sidoarjo district (East Java, Indonesia) to investigate the gas leaking properties along fractured zones that coincide with a strike-slip system in NE Java, the Watukosek Fault System. This structure has been the focus of attention since the beginning of the spectacular Lusi mud eruption on the 29th May 2006. This fault system appear to be a sinistral strike-slip system that originates from the Arjuno-Welirang volcanic complex, intersects the active Lusi eruption site displaying a system of antithetic faults, and extends towards the NE of Java where mud volcanic structures reside. In the Lusi region we completed two geochemical surveys (222Rn and 220Rn activity, CO2 and CH4 flux and concentration) along four profiles crossing the Watukosek fault system. In May 2015 two profiles ( 1.2 km long) were performed inside the 7 km2 embankment area framing the erupted mud breccia zone and across regions characterized by intense fracturing and surface deformation. In April 2017 two additional profiles ( 4 km long) were carried out in the northern and southern part outside the Lusi embankment mud eruption area, intersecting the direction of main Watukosek fault system. All the profiles highlight that the fractured zones have the highest 222Rn activity, CO2 and CH4 flux and concentration values. The relationship existing among the measured parameters suggest that the Watukosek fault system acts as a preferential pathway for active rise of deep fluids. In addition the longer profiles outside the embankment show very high average values of CO2 (5 - 8 %,v/v) and 222Rn (17 - 11.5 kBq/m3), while soil gas collected along the profiles inside the Lusi mud eruption are CH4-dominant (up to 4.5%,v/v).This suggests that inside the embankment area (i.e. covered by tens of meters thick deposits of erupted mud breccia) the seepage is overall methane-dominated. This is likely the result of microbial reactions ongoing in the organic-rich sediments producing shallow gas that gets mixed with deeper rising fluids. In contrasts profiles collected in areas not covered by the organic rich mud breccia, and that are crossing the main Watukosek fault system, have the highest 222Rn activity and CO2 concentration values. We suggest that at these localities the rise of deep fluids is not affected by shallower gas production.

Surface control bent sub for directional drilling of petroleum wells

DOEpatents

Russell, Larry R.

1986-01-01

Directional drilling apparatus for incorporation in a drill string, wherein a lower apparatus section is angularly deviated from vertical by cam action and wherein rotational displacement of the angularly deviated apparatus section is overcome by additional cam action, the apparatus being operated by successive increases and decreases of internal drill string pressure.

Stockpiling and Comprehensive Utilization of Red Mud Research Progress

PubMed Central

Liu, Dong-Yan; Wu, Chuan-Sheng

2012-01-01

With increasing production of red mud, the environmental problems caused by it are increasingly serious, and thus the integrated treatment of red mud is imminent. This article provides an overview of the composition and the basic characteristics of red mud. The research progress of safe stockpiling and comprehensive utilization of red mud is summarized. The safe stockpiling of red mud can be divided into two aspects: the design and safe operation of the stocking yard. The comprehensive utilization of red mud can be further divided into three aspects: the effective recycling of components, resource utilization and application in the field of environmental protection. This paper points out that the main focus of previous studies on red mud stockpiling is cost reproduction and land tenure. The recovery of resources from red mud has a high value-added, but low level industrialization. The use of red mud as a building material and filler material is the most effective way to reduce the stockpiling of red mud. Red mud used for environmental remediation materials is a new hotspot and worth promoting for its simple processing and low cost.

Pozzolanic Activity Assessment of LUSI (LUmpur SIdoarjo) Mud in Semi High Volume Pozzolanic Mortar

PubMed Central

Hardjito, Djwantoro; Antoni; Wibowo, Gunadi M.; Christianto, Danny

2012-01-01

LUSI mud obtained from the mud volcano in Sidoarjo, Indonesia, is a viable aluminosilicate material to be utilized as pozzolanic material. LUSI is an abbreviation of the local name of the mud, i.e., Lumpur Sidoarjo, meaning Sidoarjo mud. This paper reports the results of an investigation to assess the pozzolanic activity of LUSI mud, especially in semi high volume pozzolanic mortar. In this case, the amount of mud incorporated is between 30% to 40% of total cementitious material, by mass. The content of SiO2 in the mud is about 30%, whilst the total content of SiO2, Fe2O3 and Al2O3 is more than 70%. Particle size and degree of partial cement replacement by treated LUSI mud affect the compressive strength, the strength activity index (SAI), the rate of pozzolanic activity development, and the workability of mortar incorporating LUSI mud. Manufacturing semi high volume LUSI mud mortar, up to at least 40% cement replacement, is a possibility, especially with a smaller particle size of LUSI mud, less than 63 μm. The use of a larger percentage of cement replacement by LUSI mud does not show any adverse effect on the water demand, as the flow of the fresh mortar increased with the increase of percentage of LUSI mud usage.

High-quality heat flow determination from the crystalline basement of the south-east margin of North China Craton

NASA Astrophysics Data System (ADS)

Jiang, Guangzheng; Tang, Xiaoyin; Rao, Song; Gao, Peng; Zhang, Linyou; Zhao, Ping; Hu, Shengbiao

2016-03-01

Very few of heat flow data have come from the crystalline basement in the North China Craton but rather from boreholes in the sedimentary cover of oil-gas basins. Explorations for hot dry rock (HDR) geothermal resources and porphyry gold deposits in eastern China offer now valuable opportunities to study the terrestrial heat flow in the crystalline basement. In this study, we obtained continuous temperature logs from two boreholes (the LZ borehole with a depth of 3471 m and the DR borehole with a depth of 2179 m) located in the south-east margin of the North China Craton. The boreholes have experienced long shut-in times (442 days and 261 days for the LZ borehole and DR borehole, respectively); thus, it can be expected that the temperature conditions have re-equilibrated after drilling and drill-mud circulation. Rock thermal conductivity and radiogenic heat production were measured for 68 crystalline rock samples from these two boreholes. The measured heat-flow density was determined to be 71.8 ± 2.3 mW m-2 (for the LZ borehole) and 91.5 ± 1.2 mW m-2 (for the DR borehole). The heat flow for the LZ borehole is close to the value of 75 mW m-2 determined in the Chinese Continental Scientific Drilling main hole (CCSD MH), both being in the Sulu-Dabie orogenic belt and thus able to verify each other. The value for the DR borehole is higher than the above two values, which supports former high heat-flow values determined in the Bohai Bay Basin.

Pore Pressure and Field stress variation from Salt Water Injection; A case Study from Beaver Lodge Field in Williston Basin

NASA Astrophysics Data System (ADS)

Mohammed, R. A.; Khatibi, S.

2017-12-01

One of the major concerns in producing from oil and gas reservoirs in North American Basins is the disposal of high salinity salt water. It is a misconception that Hydro frack triggers Earthquakes, but due to the high salinity and density of water being pumped to the formation that has pore space of the rock already filled, which is not the case in Hydro-frack or Enhanced Oil Recovery in which fracturing fluid is pumped into empty pore space of rocks in depleted reservoirs. A review on the Bakken history showed that the concerns related to induce seismicity has increased over time due to variations in Pore pressure and In-situ stress that have shown steep changes in the region over the time. In this study, we focused on Pore pressure and field Stress variations in lower Cretaceous Inyan Kara and Mississippian Devonian Bakken, Inyan Kara is the major source for class-II salt-water disposal in the basin. Salt-water disposal is the major cause for induced seismicity. A full field study was done on Beaver Lodge Field, which has many salt-water disposal wells Adjacent to Oil and Gas Wells. We analyzed formation properties, stresses, pore-pressure, and fracture gradient profile in the field and. The constructed Mechanical Earth Model (MEM) revealed changes in pore pressure and stresses over time due to saltwater injection. Well drilled in the past were compared to recently drilled wells, which showed much stress variations. Safe mud weight Window of wells near proximity of injection wells was examined which showed many cases of wellbore instabilities. Results of this study will have tremendous impact in studying environmental issues and the future drilling and Fracking operations.

Testing short-range migration of microbial methane as a hydrate formation mechanism: Results from Andaman Sea and Kumano Basin drill sites and global implications

NASA Astrophysics Data System (ADS)

Malinverno, Alberto; Goldberg, David S.

2015-07-01

Methane gas hydrates in marine sediments often concentrate in coarse-grained layers surrounded by fine-grained marine muds that are hydrate-free. Methane in these hydrate deposits is typically microbial, and must have migrated from its source as the coarse-grained sediments contain little or no organic matter. In "long-range" migration, fluid flow through permeable layers transports methane from deeper sources into the gas hydrate stability zone (GHSZ). In "short-range" migration, microbial methane is generated within the GHSZ in fine-grained sediments, where small pore sizes inhibit hydrate formation. Dissolved methane can then diffuse into adjacent sand layers, where pore size does not restrict hydrate formation and hydrates can accumulate. Short-range migration has been used to explain hydrate accumulations in sand layers observed in drill sites on the northern Cascadia margin and in the Gulf of Mexico. Here we test the feasibility of short-range migration in two additional locations, where gas hydrates have been found in coarse-grained volcanic ash layers (Site NGHP-01-17, Andaman Sea, Indian Ocean) and turbidite sand beds (Site IODP-C0002, Kumano forearc basin, Nankai Trough, western Pacific). We apply reaction-transport modeling to calculate dissolved methane concentration and gas hydrate amounts resulting from microbial methane generated within the GHSZ. Model results show that short-range migration of microbial methane can explain the overall amounts of methane hydrate observed at the two sites. Short-range migration has been shown to be feasible in diverse margin environments and is likely to be a widespread methane transport mechanism in gas hydrate systems. It only requires a small amount of organic carbon and sediment sequences consisting of thin coarse-grained layers that can concentrate microbial methane generated within thick fine-grained sediment beds; these conditions are common along continental margins around the globe.

The Whole AMS Matrix: Using the Owens Lake, Ardath Slump, and Gaviota Slide cores to explore classification of ellipsoid shapes

NASA Astrophysics Data System (ADS)

Schwehr, K.; Driscoll, N.; Tauxe, L.

2004-12-01

Categorizing sediment history using Anisotropy of Magnetic Susceptibility (AMS) has been a long standing challenge for the paleomagnetic community. The goal is to have a robust test of shape fabrics that allows workers to classify sediments in terms of being primary depositional fabric, deposition in with currents, or altered fabrics. Additionally, it is important to be able to distinguish altered fabrics into such classes as slumps, crypto-slumps, drilling deformation (such as fluidization from drilling mud and flow-in), and so forth. To try to bring a unified test scheme to AMS interpretation, we are using three example test cases. First is the Owens Lake OL92 core, which has provided previous workers with a long core example in a lacustrian environment. OL92 was classified into five zones based on visual observations of the core photographs. Using these groupings, Rosenbaum et al. (2000) was able to use the deflection of the minimum eigen vector from vertical to classify each individual AMS sample. Second is the Ardath Shale location, which provides a clear case of a lithified outcrop scale problem that showed success with the bootstrap eigen value test. Finally is the Gaviota Slide in the Santa Barbara Basin, which provides usage of 1-2 meter gravity cores. Previous work has focused on Flinn, Jelinek, and bootstrap plots of eigen values. In supporting the shape characterization we have also used a 95% confidence F-Test by means of Hext's statistical work. We have extended the F-Test into a promising new plot of the F12 and F23 confidence values, which shows good clustering in early tests. We have applied all of the available techniques to the above three test cases and will present how each technique either succeeds or fails. Since each method has its own strengths and weaknesses, it is clear that the community needs to carefully evaluate which technique should be applied to any particular problem.

Determining gas hydrate distribution in sands using integrated analysis of well log and seismic data in the Terrebonne Basin, Gulf of Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hillman, Jess; Cook, Ann; Daigle, Hugh

The Terrebonne Basin is a salt bounded mini-basin in the northeast section of the Walker Ridge protraction area in the Gulf of Mexico, and the main site for an upcoming gas-hydrate focused International Ocean Discovery Program (IODP) cruise. The basin is infilled by an increasingly mud rich sedimentary sequence with several 5-15 meter gas-hydrate filled sand units of Miocene to Pliocene age overlying the up-domed salt. These gas-hydrate filled sand units can be identified in logging while drilling data from two existing wells in the Terrebonne Basin, drilled in 2009 by the Gas Hydrate Joint Industry Project (JIP) Leg 2.more » The sand units are cross cut by a distinct bottom-simulating reflector (BSR), and are clearly characterized by a polarity reversal in the sand units. The polarity reversal is caused by a positive gas-hydrate filled sand within the stability zone changing to negative gas-bearing sand. Using well data and calculated synthetic seismogram well ties we are able to identify several additional 1-4 meter gas-hydrate and water-saturated sand units associated with thick (100-200 m-thick), fine grained, hydrate bearing fractured units in the upper sedimentary sequence on the seismic data. Following on previous work, we propose that microbial generation of methane occurring within the fine-grained, fractured units acts as a source for gas hydrate formation in the thin sands. In contrast, it has been proposed that the gas hydrate in the 5-15 m-thick sands first discovered by the JIP was originates from a deeper thermogenic source. Through correlating hydrate occurrence in sands from well data, to amplitudes derived from the seismic data, we can estimate possible distribution of hydrate across the basin. Overall, we find the Terrebonne basin to be a complex gas hydrate system with multiple mechanisms of methane generation and migration.« less

Analysis of the bacterial community in aged and aging pit mud of Chinese Luzhou-flavour liquor by combined PCR-DGGE and quantitative PCR assay.

PubMed

Liang, Huipeng; Li, Wenfang; Luo, Qingchun; Liu, Chaolan; Wu, Zhengyun; Zhang, Wenxue

2015-10-01

The community structure of bacteria in aged and aging pit mud, which was judged according to their sensory and physicochemical characteristics, was analysed using polymerase chain reaction denaturing gradient gel electrophoresis (PCR-DGGE) and quantitative real-time PCR (qPCR). The phyla Firmicutes, Actinobacteria, Proteobacteria, Synergistetes and Unclassified Bacteria were detected and the fermentative Firmicutes was predominant in both types of pit mud in the PCR-DGGE analysis. Among Firmicutes, Clostridiales was dominant in aged pit mud while Bacillales and Lactobacillales were dominant in aging pit mud. The diversity of bacterial communities in aged pit mud was higher than that in aging pit mud. In the qPCR analysis the abundance of Clostridium IV in aged pit mud was higher than that in aging pit mud and there were significant differences in the quantity of Clostridium IV between aged and aging pit mud of the same cellar (P < 0.05). There were some significant differences in the microbial community structure between aged and aging pit mud. The differences in the quantity of Clostridium IV might be involved in the distinction that the aged pit mud has a strong aroma while the aging pit mud does not. © 2014 Society of Chemical Industry.

Numerical simulation of mud erosion rate in sand-mud alternate layer and comparison with experiment

NASA Astrophysics Data System (ADS)

Yoshida, T.; Yamaguchi, T.; Oyama, H.; Sato, T.

2015-12-01

For gas production from methane hydrates in sand-mud alternate layers, depressurization method is expected as feasible. After methane hydrate is dissociated, gas and water flow in pore space. There is a concern about the erosion of mud surface and it may result in flow blockage that disturbs the gas production. As a part of a Japanese National hydrate research program (MH21, funded by METI), we developed a numerical simulation of water-induced mud erosion in pore-scale sand-mud domains to model such mud erosion. The size of which is of the order of 100 micro meter. Water flow is simulated using a lattice Boltzmann method (LBM) and mud surface is treated as solid boundary with arbitrary shape, which changes with time. Periodic boundary condition is adopted at the domain boundaries, except for the surface of mud layers and the upper side. Shear stress acting on the mud surface is calculated using a momentum-exchange method. Mud layer is eroded when the shear stress exceeds a threshold coined a critical shear stress. In this study, we compared the simulated mud erosion rate with experimental data acquired from an experiment using artificial sand-mud core. As a result, the simulated erosion rate agrees well with that of the experiment.

Immobilization of copper flotation waste using red mud and clinoptilolite.

PubMed

Coruh, Semra

2008-10-01

The flash smelting process has been used in the copper industry for a number of years and has replaced most of the reverberatory applications, known as conventional copper smelting processes. Copper smelters produce large amounts of copper slag or copper flotation waste and the dumping of these quantities of copper slag causes economic, environmental and space problems. The aim of this study was to perform a laboratory investigation to assess the feasibility of immobilizing the heavy metals contained in copper flotation waste. For this purpose, samples of copper flotation waste were immobilized with relatively small proportions of red mud and large proportions of clinoptilolite. The results of laboratory leaching demonstrate that addition of red mud and clinoptilolite to the copper flotation waste drastically reduced the heavy metal content in the effluent and the red mud performed better than clinoptilolite. This study also compared the leaching behaviour of metals in copper flotation waste by short-time extraction tests such as the toxicity characteristic leaching procedure (TCLP), deionized water (DI) and field leach test (FLT). The results of leach tests showed that the results of the FLT and DI methods were close and generally lower than those of the TCLP methods.

Use of fly ash, phosphogypsum and red mud as a liner material for the disposal of hazardous zinc leach residue waste.

PubMed

Coruh, Semra; Ergun, Osman Nuri

2010-01-15

Increasing amounts of residues and waste materials coming from industrial activities in different processes have become an increasingly urgent problem for the future. The release of large quantities of heavy metals into the environment has resulted in a number of environmental problems. The present study investigated the safe disposal of the zinc leach residue waste using industrial residues such as fly ash, phosphogypsum and red mud. In the study, leachability of heavy metals from the zinc leach residue has been evaluated by mine water leaching procedure (MWLP) and toxicity characteristic leaching procedure (TCLP). Zinc removal from leachate was studied using fly ash, phosphogypsum and red mud. The adsorption capacities and adsorption efficiencies were determined. The adsorption rate data was analyzed according to the pseudo-second-order kinetic, Elovich kinetic and intra-particle diffusion kinetic models. The pseudo-second-order kinetic was the best fit kinetic model for the experimental data. The results show that addition of fly ash, phosphogypsum and red mud to the zinc leach residue drastically reduces the heavy metal content in the leachate and could be used as liner materials.

Mud volcanoes on Mars?

NASA Technical Reports Server (NTRS)

Komar, Paul D.

1991-01-01

The term mud volcano is applied to a variety of landforms having in common a formation by extrusion of mud from beneath the ground. Although mud is the principal solid material that issues from a mud volcano, there are many examples where clasts up to boulder size are found, sometimes thrown high into the air during an eruption. Other characteristics of mud volcanoes (on Earth) are discussed. The possible presence of mud volcanoes, which are common and widespread on Earth, on Mars is considered.

Geothermal well drilling manual at Cerro Prieto

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fernandez P., A.; Flores S., M.

The objective of the drilling manual is to solve all problems directly related to drilling during the construction of a well. In this case, the topics dealt which are drilling fluids and hydraulics to be applied in the field to improve drilling progress, eliminate risks and achieve good well-completion. There are other topics that are applicable such as drill bits and the drilling string, which are closely linked to drilling progress. On this occasion drilling fluid and hydraulics programs are presented, in addition to a computing program for a Casio FX-502P calculator to be applied in the field to optimizemore » hydraulics and in the analysis of hydraulics for development and exploration wells at their different intervals.« less

43 CFR 3207.12 - What work am I required to perform each year for BLM to continue the initial and additional...

Code of Federal Regulations, 2013 CFR

2013-10-01

...: (1) Geologic investigation and analysis; (2) Drilling temperature gradient wells; (3) Core drilling; (4) Geochemical or geophysical surveys; (5) Drilling production or injection wells; (6) Reservoir... lease at the end of that year unless you qualify for a drilling extension under § 3207.13. (i) Every...

43 CFR 3207.12 - What work am I required to perform each year for BLM to continue the initial and additional...

Code of Federal Regulations, 2012 CFR

2012-10-01

...: (1) Geologic investigation and analysis; (2) Drilling temperature gradient wells; (3) Core drilling; (4) Geochemical or geophysical surveys; (5) Drilling production or injection wells; (6) Reservoir... lease at the end of that year unless you qualify for a drilling extension under § 3207.13. (i) Every...

43 CFR 3207.12 - What work am I required to perform each year for BLM to continue the initial and additional...

Code of Federal Regulations, 2014 CFR

2014-10-01

...: (1) Geologic investigation and analysis; (2) Drilling temperature gradient wells; (3) Core drilling; (4) Geochemical or geophysical surveys; (5) Drilling production or injection wells; (6) Reservoir... lease at the end of that year unless you qualify for a drilling extension under § 3207.13. (i) Every...

43 CFR 3207.12 - What work am I required to perform each year for BLM to continue the initial and additional...

Code of Federal Regulations, 2011 CFR

2011-10-01

...: (1) Geologic investigation and analysis; (2) Drilling temperature gradient wells; (3) Core drilling; (4) Geochemical or geophysical surveys; (5) Drilling production or injection wells; (6) Reservoir... lease at the end of that year unless you qualify for a drilling extension under § 3207.13. (i) Every...

Linked halokinesis and mud volcanism at the Mercator mud volcano, Gulf of Cadiz

NASA Astrophysics Data System (ADS)

Perez-Garcia, Carolina; Berndt, Christian; Klaeschen, Dirk; Mienert, Jürgen; Haffert, Laura; Depreiter, Davy; Haeckel, Matthias

2011-05-01

Mud volcanoes are seafloor expressions of focused fluid flow that are common in compressional tectonic settings. New high-resolution 3-D seismic data from the Mercator mud volcano (MMV) and an adjacent buried mud volcano (BMV) image the internal structure of the top 800 m of sediment at both mud volcanoes, revealing that both are linked and have been active episodically. The total volumes of extruded mud range between 0.15 and 0.35 km3 and 0.02-0.05 km3 for the MMV and the BMV, respectively. The pore water composition of surface sediment samples suggests that halokinesis has played an important role in the evolution of the mud volcanoes. We propose that erosion of the top of the Vernadsky Ridge that underlies the mud volcanoes activated salt movement, triggering deep migration of fluids, dissolution of salt, and sediment liquefaction and mobilization since the end of the Pliocene. Since beginning of mud volcanism in this area, the mud volcanoes erupted four times while there was only one reactivation of salt tectonics. This implies that there are other mechanisms that trigger mud eruptions. The stratigraphic relationship of mudflows from the MMV and BMV indicates that the BMV was triggered by the MMV eruptions. This may either be caused by loading-induced hydrofracturing within the BMV or due to a common feeder system for both mud volcanoes. This study shows that the mud volcanoes in the El Arraiche mud volcano field are long-lived features that erupt with intervals of several tens of thousands of years.

Organic chemical composition of mud from the LUSI mud volcano, Sidoarjo, East Java, Indonesia

NASA Astrophysics Data System (ADS)

Rosenbauer, R. J.; Campbell, P.; Lam, A.

2009-12-01

Sidoarjo, East Java, Indonesia is the site of LUSI, a terrestrial mud volcano that has been erupting since May 29, 2006. In response to a U.S. Department of State request, the U.S. Geological Survey has been assisting the Indonesian Government to describe the geological and geochemical aspects and potential health risk of the mud eruption. We report here on the organic chemical composition of the mud. Organic chemical analyses were carried out by gas chromatography/mass spectroscopy following organic extraction by microwave-assisted solvent extraction and compound fractionation by adsorption chromatography. There is a petroliferous component in the mud that is fresh, immature, and nonbiodegraded. There is a complete suite of n-alkanes with a bell-shaped pattern typical of fresh petroleum with a Cmax around C20. The alkane content ranges from 0.12 to 1.01 mg/kg dry mud. The presence of certain hopanes (i.e. 17 α,21β(H)-30-norhopane and 17α,21β(H)-hopane) is also indicative of the presence of oil. The proportions of other biomarker compounds (pristane/phytane = 2.4) and the dominance of the C27 sterane (5α(H),14α(H),17α(H)-chlolestane) suggest that oil formed under oxic conditions and has a likely coastal marine or terrigenous source. The presence of oleanane indicates a Cretaceous or younger age for the petrogenic material. These geochemical parameters are consistent with Indonesian oil derived from Tertiary marlstone source rocks that contained kerogen deposited under oxic conditions, probably the upper Miocene Klasafet Formation. Polycyclic aromatic hydrocarbons (PAHs) are present and range in content from 0.1 to 2.2 mg/kg dry mud. The low molecular weight (LMW) PAHs, in particular, naphthalene and methyl-naphthalene are dominant except for perylene which is ubiquitous in the environment. The presence of both parent and higher homologue PAHs indicate a petrogenic rather than combustion source. PAHs are known carcinogens but toxicity data in sediments are sparse and often qualitative, depending on the PAH matrix and thus bioavailability. The distribution and content of PAHs measured in the LUSI mud do exceed USEPA recommended interim sediment quality criteria. In addition, judging sediment toxicity on the basis of single PAH compounds risks underestimating effects because mixtures of PAHs tend to aggregate toxicity. Further studies are needed to determine whether or not PAHs are present in levels that exceed soil remediation or aquatic guidelines. The mud contains low levels (tens of ppb) of the higher plant sterols including stigmasterol and β-sitosterol. Also, 22-dehydrocholesterol (generally ascribed to algal material) is present at 39 ppb. These compounds are derived from natural sources, are non-hazardous, and were likely entrained in the mud during ascent to the surface or mixed with the mud post-eruption. The organic compounds identified to date will exhibit a variety of environmental behaviors and effects. Some compounds will volatilize and photo-oxidize or biodegrade relatively quickly (i.e. n-alkanes), and are relatively nontoxic. LMW PAHs are sparingly soluble in water but heavier PAHs will likely persist in the environment and represent potential toxicity to biota because PAHs are bio-accumulative. But the overall toxicity of the mud appears low.

An Overview of Downhole Imaging Tools

NASA Astrophysics Data System (ADS)

Luthi, S. M.

In this presentation we give an overview of downhole imaging tools that can be used to image the borehole wall and its vicinity with a variety of physical methods. Among these are ultrasonic scans with a rotating transducer that performs a pulse-echo mea- surement in rapid succession. This gives a transit time and a reflected amplitude image of the borehole wall. Electrical imaging is done with a whole family of measurements that operate mostly in the low AC range. All of them feature a number of electrodes that is inversely proportional to the desired resolution and depth of investigation. They image layering, fracturing and other heterogeneities in the rocks traversed by the bore- hole. Some of these images can be recorded and transmitted to the surface in real-time while the well is being drilled. Imaging using nuclear methods is also possible, for ex- ample for the natural radioactivity, density, or neutron porosity of the rock. However, these devices have generally low spatial resolutions. Finally, optical imaging is pos- sible in translucent and slightly opaque muds with a downhole video camera. Recent developments have resulted in a device that can withstand high pressures and temper- atures and that transmits live video images to the surface in real-time. This method has the highest resolution but is of limited applicability in the oil industry where gener- ally opaque muds are used. These images can be successfully used to determined the structural and intrinsic properties of rock traversed by a borehole.

Geology and mineral resources of the Mud Springs Ranch Quadrangle, Sweetwater County, Wyoming

USGS Publications Warehouse

Roehler, Henry W.

1979-01-01

The Mud Springs Ranch quadrangle occupies an area of 56 mF (square miles) on the southeast flank of the Rock Springs uplift in southwestern Wyoming. The climate is arid and windy. The landscape is mostly poorly vegetated and consists of north-trending ridges and valleys that are dissected by dry drainages. Sedimentary rocks exposed in the quadrangle are 5,400 ft (feet) thick and are mostly gray sandstone, siltstone, and shale, gray and brown carbonaceous shale, and thin beds of coal. They compose the Blair, Rock Springs, Ericson, Almond, and Lewis Formations of Cretaceous age and the Fort Union Formation of Paleocene age. The structure is mostly homoclinal, having southeast dips of 5?-12? in the northern part of the quadrangle, but minor plunging folds and one small fault are present in the southern part of the quadrangle. Three coal beds in the Fort Union Formation and 15 coal beds in the Almond Formation exceed 2.5 ft in thickness, are under less than 3,000 ft of overburden, and are potentially minable. Geographic stratigraphic, and resource data are present for each bed of minable coal. The total minable coal resources are estimated to be about 283 million short tons. Nine coal and rock samples from outcrops were analyzed to determine their quality and chemical composition. Four dry oil and gas test wells have been drilled within the quadrangle area, but structurally controlled stratigraphic-trap prospects remain untested.

Mud volcanoes of the Orinoco Delta, Eastern Venezuela

USGS Publications Warehouse

Aslan, A.; Warne, A.G.; White, W.A.; Guevara, E.H.; Smyth, R.C.; Raney, J.A.; Gibeaut, J.C.

2001-01-01

Mud volcanoes along the northwest margin of the Orinoco Delta are part of a regional belt of soft sediment deformation and diapirism that formed in response to rapid foredeep sedimentation and subsequent tectonic compression along the Caribbean-South American plate boundary. Field studies of five mud volcanoes show that such structures consist of a central mound covered by active and inactive vents. Inactive vents and mud flows are densely vegetated, whereas active vents are sparsely vegetated. Four out of the five mud volcanoes studied are currently active. Orinoco mud flows consist of mud and clayey silt matrix surrounding lithic clasts of varying composition. Preliminary analysis suggests that the mud volcano sediment is derived from underlying Miocene and Pliocene strata. Hydrocarbon seeps are associated with several of the active mud volcanoes. Orinoco mud volcanoes overlie the crest of a mud-diapir-cored anticline located along the axis of the Eastern Venezuelan Basin. Faulting along the flank of the Pedernales mud volcano suggests that fluidized sediment and hydrocarbons migrate to the surface along faults produced by tensional stresses along the crest of the anticline. Orinoco mud volcanoes highlight the proximity of this major delta to an active plate margin and the importance of tectonic influences on its development. Evaluation of the Orinoco Delta mud volcanoes and those elsewhere indicates that these features are important indicators of compressional tectonism along deformation fronts of plate margins. ?? 2001 Elsevier Science B.V. All rights reserved.

High-Resolution Seafloor Observations of an Active Mud Volcano Offshore SW Taiwan - Results of a Repeated Survey after Four Years

NASA Astrophysics Data System (ADS)

Hsu, H. H.; Chen, T. T.; Liu, C. S.; Su, C. C.; Paull, C. K.; Caress, D. W.; Gwiazda, R.; Chen, Y. H.

2017-12-01

Mud Volcano V (MV5) is an active submarine mud volcano sitting on top of a mud diapir ridge at water depths of 600 m in the active margin offshore of southwestern Taiwan. This cone-shape mud volcano is almost 3-km-wide, 200-m-high, with 9.5° slopes, and explosively ejects streams of mud every 1.5-3 minutes. It was first mapped in 2013 with MBARI's mapping AUV (autonomous underwater vehicle). In 2017, a repeated AUV mapping survey was conducted to see if significant bathymetric changes took place since 2013, and to investigate the fluxes of fluids that pass through diapiric structures in an active continental margin. In addition to high-resolution bathymetry (1-m-resolution), sub-bottom profiling and side-scan sonar data acquired by the AUV, and videos and samples collected by MBARI's miniROV, we also incorporate multichannel seismic reflection data and gravity core sample analyses in this study. AUV bathymetry data reveal that there are two gryphons on the eastern slope of MV5. In the 2017 survey the mapped sizes of the two side cones were 80 m wide, 35 m long, 20 m relief and 40 m wide, 40 m long, 12 m relief, respectively. Comparing the bathymetry mapped in the 2017 AUV survey with that surveyed in 2013, no obvious overall morphological changes in MV5 are detected, except around the two gryphons. In the time period between the surveys, due to venting of mud from the two gryphons, two series of flow deposits which can be up to 5 meters thick are observed along the slope in the east side of both gryphons. The center depressions of these two gryphons have increased by 1-5 meters depth in their west side. Seismic and sub-bottom profiles reveal amplitude anomalies in the sub-strata of MV5 which indicate possible fluid migration paths of mud flows from deep. The trace of mud flow from the top of MV5 to its foot can be delineated from the side-scan sonar images. On the basis of 210Pbex chronology dating method, the sedimentation rate on the surface of MV5 is very slow (0.057 cm/y). High methane anomalies are discovered on MV5 based on the geochemical analysis results of gravity core samples, but the heat probe did not detect obvious temperature changes before and after venting episodes in the 2017 survey. Based on this comprehensive study, a three-step model is proposed to explain mud volcano venting processes in the active margin offshore of SW Taiwan.

Closure Report for Corrective Action Unit 544: Cellars, Mud Pits, and Oil Spills, Nevada National Security Site, Nevada, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark Krauss and Catherine Birney

2011-05-01

This Closure Report (CR) presents information supporting the closure of Corrective Action Unit (CAU) 544: Cellars, Mud Pits, and Oil Spills, Nevada National Security Site, Nevada. This CR complies with the requirements of the Federal Facility Agreement and Consent Order that was agreed to by the State of Nevada; U.S. Department of Energy (DOE), Environmental Management; U.S. Department of Defense; and DOE, Legacy Management. The corrective action sites (CASs) within CAU 544 are located within Areas 2, 7, 9, 10, 12, 19, and 20 of the Nevada National Security Site. Corrective Action Unit 544 comprises the following CASs: • 02-37-08,more » Cellar & Mud Pit • 02-37-09, Cellar & Mud Pit • 07-09-01, Mud Pit • 09-09-46, U-9itsx20 PS #1A Mud Pit • 10-09-01, Mud Pit • 12-09-03, Mud Pit • 19-09-01, Mud Pits (2) • 19-09-03, Mud Pit • 19-09-04, Mud Pit • 19-25-01, Oil Spill • 19-99-06, Waste Spill • 20-09-01, Mud Pits (2) • 20-09-02, Mud Pit • 20-09-03, Mud Pit • 20-09-04, Mud Pits (2) • 20-09-06, Mud Pit • 20-09-07, Mud Pit • 20-09-10, Mud Pit • 20-25-04, Oil Spills • 20-25-05, Oil Spills The purpose of this CR is to provide documentation supporting the completed corrective actions and data confirming that the closure objectives for CASs within CAU 544 were met. To achieve this, the following actions were performed: • Review the current site conditions, including the concentration and extent of contamination. • Implement any corrective actions necessary to protect human health and the environment. • Properly dispose of corrective action and investigation wastes. • Document Notice of Completion and closure of CAU 544 issued by the Nevada Division of Environmental Protection.« less

Use of Cutting-Edge Horizontal and Underbalanced Drilling Technologies and Subsurface Seismic Techniques to Explore, Drill and Produce Reservoired Oil and Gas from the Fractured Monterey Below 10,000 ft in the Santa Maria Basin of California

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Witter; Robert Knoll; William Rehm

2006-06-30

This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conductedmore » in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper curved sections were drilled and lined through the problematic shale member without major stability problems. The top of the targeted Monterey was thought to be seen at the expected TVD of 10,000 ft where the 7-in. liner was set at a 60{sup o} hole angle. Significant oil and gas shows suggested the fractured interval anticipated at the heel location had been penetrated. A total of 2572 ft of 6{Delta}-in. near-horizontal interval was placed in the shale section, extending planned well length by approximately 470 ft. Very little hydrocarbon in-flow was observed from fractures along the productive interval. This may be a result of the well trajectory falling underneath the Monterey fractured zone. Hydrocarbon observations, cuttings analysis and gamma-ray response indicated additional fractured intervals were accessed along the last {+-}900 ft of well length. The well was completed with a 2 and 7/8-in. tubing string set in a production packer in preparation for flow and swab tests to be conducted later by a service rig. The planned well time was estimated as 39 days and overall cost as $2.4 million. The actual results are 66 days at a total cost of $3.4 million. Well productivity responses during subsequent flow and swabbing tests were negative. The well failed to inflow and only minor amounts (a few barrels) of light oil were recovered. The lack of production may suggest that actual sustainable reservoir pressure is far less than anticipated. Temblor attempted in July, 2006, to re-enter and clean out the well and run an Array Induction log (primarily for resistivity and correlation purposes), and an FMI log (for fracture detection). Application of surfactant in the length of the horizontal hole, and acid over the fracture zone at 10,236 was also planned. This attempt was not successful in that the clean out tools became stuck and had to be abandoned.« less

Cyclic Activity of Mud Volcanoes: Evidences from Trinidad (SE Caribbean)

NASA Astrophysics Data System (ADS)

Deville, E.

2007-12-01

Fluid and solid transfer in mud volcanoes show different phases of activity, including catastrophic events followed by periods of relative quiescence characterized by moderate activity. This can be notably shown by historical data onshore Trinidad. Several authors have evoked a possible link between the frequencies of eruption of some mud volcanoes and seismic activity, but in Trinidad there is no direct correlation between mud eruptions and seisms. It appears that each eruptive mud volcano has its own period of catastrophic activity, and this period is highly variable from one volcano to another. The frequency of activity of mud volcanoes seems essentially controlled by local pressure regime within the sedimentary pile. At the most, a seism can, in some cases, activate an eruption close to its term. The dynamics of expulsion of the mud volcanoes during the quiescence phases has been studied notably from temperature measurements within the mud conduits. The mud temperature is concurrently controlled by, either, the gas flux (endothermic gas depressurizing induces a cooling effect), or by the mud flux (mud is a vector for convective heat transfer). Complex temperature distribution was observed in large conduits and pools. Indeed, especially in the bigger pools, the temperature distribution characterizes convective cells with an upward displacement of mud above the deep outlet, and ring-shaped rolls associated with the burial of the mud on the flanks of the pools. In simple, tube-like shaped, narrow conduits, the temperature is more regular, but we observed different types of profiles, with either downward increasing or decreasing temperatures. If the upward flow of mud would be regular, we should expect increasing temperatures and progressively decreasing gradient with depth within the conduits. However, the variable measured profiles from one place to another, as well as time-variable measured temperatures within the conduits and especially, at the base of the conduits, shows that the fluid flow expelled by the studied mud volcanoes is not constant but highly variable through short time-periods. We notably observed very short time-period cyclic variations with a frequency of about 10 minutes. These high frequencies temperature changes could be related to the dynamics of two-phase flows (gas and mud) through the mud volcano conduits. We also observed locally a significant daily changes of the temperature of the expelled mud which shows also that the mud flux is changing very rapidly from one day to another.

Preliminary analytical results for a mud sample collected from the LUSI Mud Volcano, Sidoarjo, East Java, Indonesia

USGS Publications Warehouse

Plumlee, Geoffrey S.; Casadevall, Thomas J.; Wibowo, Handoko T.; Rosenbauer, Robert J.; Johnson, Craig A.; Breit, George N.; Lowers, Heather; Wolf, Ruth E.; Hageman, Philip L.; Goldstein, Harland L.; Anthony, Michael W.; Berry, Cyrus J.; Fey, David L.; Meeker, Gregory P.; Morman, Suzette A.

2008-01-01

On May 29, 2006, mud and gases began erupting unexpectedly from a vent 150 meters away from a hydrocarbon exploration well near Sidoarjo, East Java, Indonesia. The eruption, called the LUSI (Lumpur 'mud'-Sidoarjo) mud volcano, has continued since then at rates as high as 160,000 m3 per day. At the request of the United States Department of State, the U.S. Geological Survey (USGS) has been providing technical assistance to the Indonesian Government on the geological and geochemical aspects of the mud eruption. This report presents initial characterization results of a sample of the mud collected on September 22, 2007, as well as inerpretive findings based on the analytical results. The focus is on characteristics of the mud sample (including the solid and water components of the mud) that may be of potential environmental or human health concern. Characteristics that provide insights into the possible origins of the mud and its contained solids and waters have also been evaluated.

Drilling Polar Oceans with the European Research Icebreaker AURORA BOREALIS: the IODP Context

NASA Astrophysics Data System (ADS)

Lembke-Jene, Lester; Wolff-Boenisch, Bonnie; Azzolini, Roberto; Thiede, Joern; Biebow, Nicole; Eldholm, Olav; Egerton, Paul

2010-05-01

Polar oceans are characterized by extreme environmental conditions for humans and materials, and have remained the least accessible regions to scientists of the IODP. DSDP and ODP have for long faced specific technical and logistical problems when attempting to drill in ice-covered polar deep-sea basins. The Arctic Ocean and large areas of the high-latitude Southern Ocean remained largely un-sampled by ODP and remain one of the major scientific and technological challenges for IODP. Drilling in these regions has been discussed and anticipated for decades and the scientific rationales are reflected in the science plans of the international Nansen Arctic Drilling Program (NAD) or the Arctic Program Planning Group (APPG) of ODP/IODP, amongst others. More recently, the rationale to investigate the polar oceans in a holistic approach has been outlined by workshops, leading to strategic assessments of the scientific potential and new drilling proposals. The European Polar Board took the initiative to develop a plan for a novel and dedicated research icebreaker with technical capabilities hitherto unrealised. This research icebreaker will enable autonomous operations in the central Arctic Ocean and the Southern Ocean, even during the severest ice conditions in the deep winter, serving all marine disciplines of polar research including scientific drilling: The European Research Icebreaker and Deep-Sea Drilling Vessel AURORA BOREALIS. AURORA BOREALIS is presently planned as a multi-purpose vessel. The ship can be deployed as a research icebreaker in all polar waters during any season of the year, as it shall meet the specifications of the highest ice-class attainable (IACS Polar Code 1) for icebreakers. During the times when it is not employed for drilling, it will operate as the most technically advanced multi-disciplinary research vessel in the Arctic or polar Southern Ocean. AURORA BOREALIS will be a "European scientific flagship facility" (fully open to non-European partners), a multidisciplinary platform for studies ranging from the sub-seafloor into the atmosphere. AURORA BOREALIS was planned for her role in deep-sea drilling in consultation with engineers and technical experts familiar with the program and the operation of these vessels. All techniques currently deployed on IODP expeditions can be implemented onboard the vessel under polar weather and ice conditions, including the full range of re-entry, casing and cementing, and instrumentation options and the entire suite of downhole logging tools. Due to sufficient laboratory space, a full analytical workflow can be easily established comparable to existing permanent platforms, including clean rooms, diverse scanning and logging or incubation facilities. While the vessel is equipped with a dedicated deep-sea drilling rig, other coring and drilling techniques can be employed if needed (e.g. Rockdrill, MEBO, large diameter Kasten cores). AURORA BOREALIS is fitted to operate a CALYPSO Piston Coring System in polar waters. Future mud-return systems under consideration and testing for IODP to provide controlled borehole conditions in difficult facies are compatible with the layout of AURORA BOREALIS. The berthing capacity of 120 personnel total (scientists, technical support and crew) allows to accommodate a sufficient number of science party members offshore. The present scientific implementation documents plan for about one polar scientific drilling expedition per year in a to-be-determined configuration. As the vessel is a multi-dsiciplinary platform, operations for the entire year are not dependant on drilling operations alone. While principal access to the vessel will be based on a competitive proposal review and evaluation system, the allocation of timeslots specifically for drilling would preferably be given over to IODP handling and planning systems in a cooperative mode using the strengths and capacitites of the future program. Depending on interests and needs of the scientific communities a preferential focus in non-drilling expedition planning could be established e.g. for dedicated geophysical pre-site survey works in areas inaccessible by other vessels to secure critical data needed for later drilling expeditions. Based on ongoing expert consultations, it is safe to assume that the average costs for an Arctic or polar drilling expedition will be considerably lower than with an otherwise necessary multi-ship setup based on modelled expedition scenarios and annual operational cost calculations. Still, AURORA BOREALIS shall provide substantially enhanced scientific, operational, personnel and technical capacities offshore.

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Mud program. 250.1614 Section 250.1614 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... requirements concerning mud control, mud test and monitoring equipment, mud quantities, and safety precautions...

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Mud program. 250.1614 Section 250.1614 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... requirements concerning mud control, mud test and monitoring equipment, mud quantities, and safety precautions...

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Mud program. 250.1614 Section 250.1614 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... requirements concerning mud control, mud test and monitoring equipment, mud quantities, and safety precautions...

Hydropressure tongues within regionally geopressured lower Tuscaloosa sandstone, Tuscaloosa trend, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCulloh, R.P.; Purcell, M.D.

1983-01-01

A regional study of the Tuscaloosa Formation in Louisiana, undertaken to assess geopressured-geothermal potential, revealed lobate, downdip extensions of the hydropressured zone in lower Tuscaloosa massive sandstone facies below the regional top of geopressure. Normal pressure zones within geopressured section were identified by drilling mud weights less than 13 pounds per gallon on electric logs of massive lower Tuscaloosa sandstone, and cross sections demonstrated updip continuity of these zones with the regional hydropressured zone. These hydropressure tongues are permitted by the anomalously high permeabilities reportd from the deep Tuscaloosa trend which have been attributed to both primary and secondary porosity.more » The hydropressure tongues correspond with lobes of thick net sandstone, principally in Pointe Coupee, East Feliciana, East Baton Rouge, and Livingston Parishes in the central Tuscaloosa trend. Limited control suggests at least one hydropressure tongue in the Chandeleur Sound area to the east.« less

Evaluation of the ability of calcite, bentonite and barite to enhance oil dispersion under arctic conditions.

PubMed

Jézéquel, Ronan; Receveur, Justine; Nedwed, Tim; Le Floch, Stéphane

2018-02-01

A test program was conducted at laboratory and pilot scale to assess the ability of clays used in drilling mud (calcite, bentonite and barite) to create oil-mineral aggregates and disperse crude oil under arctic conditions. Laboratory tests were performed in order to determine the most efficient conditions (type of clay, MOR (Mineral/Oil Ratio), mixing energy) for OMA (Oil Mineral Aggregate) formation. The dispersion rates of four crude oils were assessed at two salinities. Dispersion was characterized in terms of oil concentration in the water column and median OMA size. Calcite appeared to be the best candidate at a MOR of 2:5. High mixing energy was required to initiate OMA formation and low energy was then necessary to prevent the OMAs from resurfacing. Oil dispersion using Corexit 9500 was compared with oil dispersion using mineral fines. Copyright © 2017 Elsevier Ltd. All rights reserved.

Electromagnetic anti-jam telemetry tool

DOEpatents

Ganesan, Harini [Sugar Land, TX; Mayzenberg, Nataliya [Missouri City, TX

2008-02-12

A mud-pulse telemetry tool includes a tool housing, a motor disposed in the tool housing, and a magnetic coupling coupled to the motor and having an inner shaft and an outer shaft. The tool may also include a stator coupled to the tool housing, a restrictor disposed proximate the stator and coupled to the magnetic coupling, so that the restrictor and the stator adapted to generate selected pulses in a drilling fluid when the restrictor is selectively rotated. The tool may also include a first anti-jam magnet coupled to the too housing, and an second anti-jam magnet disposed proximate the first anti-jam magnet and coupled to the inner shaft and/or the outer shaft, wherein at least one of the first anti-jam magnet and the second anti-jam magnet is an electromagnet, and wherein the first anti-jam magnet and the second anti-jam magnet are positioned with adjacent like poles.

Cortical bone drilling: An experimental and numerical study.

PubMed

Alam, Khurshid; Bahadur, Issam M; Ahmed, Naseer

2014-12-16

Bone drilling is a common surgical procedure in orthopedics, dental and neurosurgeries. In conventional bone drilling process, the surgeon exerts a considerable amount of pressure to penetrate the drill into the bone tissue. Controlled penetration of drill in the bone is necessary for safe and efficient drilling. Development of a validated Finite Element (FE) model of cortical bone drilling. Drilling experiments were conducted on bovine cortical bone. The FE model of the bone drilling was based on mechanical properties obtained from literature data and additionally conducted microindentation tests on the cortical bone. The magnitude of stress in bone was found to decrease exponentially away from the lips of the drill in simulations. Feed rate was found to be the main influential factor affecting the force and torque in the numerical simulations and experiments. The drilling thrust force and torque were found to be unaffected by the drilling speed in numerical simulations. Simulated forces and torques were compared with experimental results for similar drilling conditions and were found in good agreement.CONCLUSIONS: FE schemes may be successfully applied to model complex kinematics of bone drilling process.

Opon gas renews interest in the hydrocarbon prolific middle Magdalena basin, Colombia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, D.M.; Elliott, R.; Latimer, G.

1996-08-01

A total of 45 fields have been discovered in the Middle Magdelena basin of Colombia since 1918. In August 1994, the Amoco-operated Opon-3 well tested significant hydrocarbons in the basin. The well flowed 45 MMCFGPD and 2000 BCPD from 1118 ft of perforations between 10,018 and 12,348 feet. A second well, Opon-4, tested 58 MMCFGPD from the same interval. Opon now appears to be a significant gas condensate field. A full assessment of commercial potential requires 3D seismic data, as well as further development drilling. Operational challenges include: drilling, coring, logging, cementing and testing in a world-record setting 23 ppgmore » hematite-weighted mud environment involving simultaneous perforation over a 2330 ft gross pay interval and management of high production rates at >8000 psi FwHP. The Opon structure is a surface anticline on the western edge of the Eastern Cordillera fold and thrust belt. Seismic definition of the trap, however, is complicated by multiple faults, steep dips, rugged topography and variable surface velocities. The main gas reservoirs are fluvial sandstones of the Eocene La Paz Formation sealed by the overlying upper Eocene Las Esmeraldas Formation shales. Individual producing sandstones range from 40 to 200 ft thick in a minimum gross gas column of 4200 ft. Average porosity is 6%. Tectonically induced fractures probably enhance reservoir performance.« less

Geoacoustic Characterization of the Mud Drape at the New England Mud Patch

NASA Astrophysics Data System (ADS)

Reed, A. H.

2016-02-01

The New England Mud Patch is an extensive deposit of fine-grained sediments that extends from an area south of Cape Cod, MA to south of Montauk Point Long Island, NY out on the continental shelf in water depths of 60 to 90 meters. The mud patch has a remarkable accumulation of up to a 13 meter thick sequence of mud that overlays a transgressive surface of Pleistocene Age and then thins out on the periphery where surficial sediments convert from mud to sand and sand/gravel. The deposit likely accumulated in this region due to the coalescing of shelf currents that had oppositional flow. This work focuses on a section of the mud patch that is centered over the thickest portion of mud and extends east-west for 30 km and north south for 10 km. Gravity cores were collected throughout this region and the cores penetrated the upper 2-4 m of mud at 28 different sites with multiple cores collected in several locations. The mud thickness in these regions exceeded the core barrel length, therefore the cores did not penetrate into the basal sand sediment layer, a relict transgressional horizon, which displays prominently in the acoustic data for this selected region. These cores were evaluated for compressional sound speed (averaging 1480 m/s) and density (1580 kg/m3) and found to be largely homogeneous and similar throughout the study area. The largest source of inhomogeneity was due to dispersed shell hash and disarticulated bivalves, but these inclusions represent minor components in the total sediment volume. The overlying sediment that characterizes the New England Mud Patch can be readily classified as mud, silty mud, or sandy-silty mud. This fine-grained sediment deposit reflects upon the low-energy nature of the hydrodynamics within this region.

Shallow-Water Mud Acoustics

DTIC Science & Technology

2015-09-30

1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Shallow- Water Mud Acoustics William L. Siegmann...shallow water over mud sediments and of acoustic detection, localization, and classification of objects buried in mud. OBJECTIVES • Develop...including long-range conveyance of information; detection, localization, and classification of objects buried in mud; and improvement of shallow water

46 CFR 128.450 - Liquid-mud systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Liquid-mud systems. 128.450 Section 128.450 Shipping...: EQUIPMENT AND SYSTEMS Design Requirements for Specific Systems § 128.450 Liquid-mud systems. (a) Liquid-mud... this chapter. (b) Tanks for oil-based liquid mud must be fitted with tank vents equipped with flame...

Binding of Vapour-Phase Mercury (Hg0) on Chemically Treated Bauxite Residues (Red Mud)

EPA Science Inventory

In this study, Hg capture using red mud, seawater-neutralized red mud, and acid-treated red mud is evaluated and compared to other, more conventional sorbent materials. Red mud (also known as bauxite residue) is a by-product of extracting alumina from ground bauxite ore by treati...

Gas geochemistry studies at the gas hydrate occurrence in the permafrost environment of Mallik (NWT, Canada)

NASA Astrophysics Data System (ADS)

Wiersberg, T.; Erzinger, J.; Zimmer, M.; Schicks, J.; Dahms, E.; Mallik Working Group

2003-04-01

We present real-time mud gas monitoring data as well as results of noble gas and isotope investigations from the Mallik 2002 Production Research Well Program, an international research project on Gas Hydrates in the Northwest Territories of Canada. The program participants include 8 partners; The Geological Survey of Canada (GSC), The Japan National Oil Corporation (JNOC), GeoForschungsZentrum Potsdam (GFZ), United States Geological Survey (USGS), United States Department of the Energy (USDOE), India Ministry of Petroleum and Natural Gas (MOPNG)/Gas Authority of India (GAIL) and the Chevron-BP-Burlington joint venture group. Mud gas monitoring (extraction of gas dissolved in the drill mud followed by real-time analysis) revealed more or less complete gas depth profiles of Mallik 4L-38 and Mallik 5L-38 wells for N_2, O_2, Ar, He, CO_2, H_2, CH_4, C_2H_6, C_3H_8, C_4H10, and 222Rn; both wells are approx. 1150 m deep. Based on the molecular and and isotopic composition, hydrocarbons occurring at shallow depth (down to ˜400 m) are mostly of microbial origin. Below 400 m, the gas wetness parameter (CH_4/(C_2H_6 + C_3H_8)) and isotopes indicate mixing with thermogenic gas. Gas accumulation at the base of permafrost (˜650 m) as well as δ13C and helium isotopic data implies that the permafrost inhibits gas flux from below. Gas hydrate occurrence at Mallik is known in a depth between ˜890 m and 1100 m. The upper section of the hydrate bearing zone (890 m--920 m) consists predominantly of methane bearing gas hydrates. Between 920 m and 1050 m, concentration of C_2H_6, C_3H_8, and C_4H10 increases due to the occurrence of organic rich sediment layers. Below that interval, the gas composition is similar to the upper section of the hydrate zone. At the base of the hydrate bearing zone (˜1100 m), elevated helium and methane concentrations and their isotopic composition leads to the assumption that gas hydrates act as a barrier for gas migration from below. In mud gas samples from the hydrate zone, the concentrations of all noble gases are lower than in air. Using Ne as a tracer for air contamination, the air-normalized abundances of Ar, Ke and Xe in those samples increase with their mass. Non-atmospheric elemental ratios of the heavier noble gases are most possible the result of elemental fractionation during hydrate formation.

Modern Estuarine Sedimentation in Suisun Bay, California

NASA Astrophysics Data System (ADS)

Chin, J. L.; Orzech, K.; Anima, R. J.; Jaffe, B.

2002-12-01

Suisun Bay is the northeasternmost part of San Francisco Bay (California), the largest estuary on the Pacific Coast of the United States. Suisun Bay's geographic and morphologic position are unique in that it occupies the head of the estuary and is subject to the maximum freshwater inflow and sediment input of the Sacramento-San Joaquin Rivers, whose drainage basin covers 40% of the land area of California. Suisun Bay consists of two smaller subembayments, Grizzly and Honker Bays. Gravity cores obtained in 1990-1991 and 1999 were analyzed to delineate depositional environments and sedimentation patterns in Suisun Bay. Major depositional environments include: tidal channel (subtidal), tidal channel banks (subtidal), tidal flat (intertidal to subtidal), and bay mouth (subtidal). The tidal channel environment includes both large and small channels in Suisun Bay as well as the tidal sloughs Suisun and Montezuma Sloughs. The coarsest sediment, usually sand or muddy sand, characterize this environment and water depths range from 2 to 11 m. Thin (1-2 mm) and discontinuous silt and clay laminae are common. Suisun and Montezuma Sloughs are the exception to this pattern in that they consist of massive, intensely bioturbated muds. Tidal channel banks (both "cut" and "accretionary" channel margins), particularly accretionary banks, are characterized by low-to-moderate bioturbation and sandy mud to muddy sand lithology. Typically alternating sand and mud beds (1-6 cm thick) are present; both types of beds consist of 1mm to 1cm thick subhorizontal to inclined laminae. Laminae composed of organic detritus are also present. Where this environment is transitional with the tidal flat environment water depths range from 2-8 m. Tidal flat environments include the "sand" shoals present on bathymetry charts, and are typically a bioturbated muddy sand to sandy mud. Sand and mud beds, 1-3 cm thick, are often characterized by very fine 1-2 mm thick silt and mud laminae. Water depths range from 2 to 4.5 m where these laminated tidal flat sediments occur. Bay mouth environments occur only in the distal portions of Grizzly and Honker Bays, subembayments of Suisun Bay proper. This environment is transitional with both tidal channel bank and tidal flat environments and shares characteristics with each. Massive to interbedded mud is the most common lithology, although sandy mud to muddy sand also occurs. Centimeters thick sand and mud beds typically alternate vertically. Bioturbation is low to moderate. Water depths over this environment range from 2 to 3 m. Depositional environments present in Suisun Bay are the result of a full range of tidal and fluvial processes as shown by the lithologies and alternating sediment stratigraphic patterns observed in cores. Very thin beds and intense bioturbation evidence intervals of very slow to negligible sedimentation. Rapid deposition and/or resuspension are evidenced by thick sediment intervals and by laminae that are continuous and apparently unbioturbated. Very fine scale sedimentation that may represent individual ebb and flood events as well as longer term seasonal sedimentation patterns are also present. An additional observation is that almost a quarter of the gravity cores reveal that modern estuarine deposits overlie an erosional surface that separate them from an organic-rich mud. This organic-rich mud, in one core to date, has been radiocarbon dated at roughly 4500 yrs. B.P. (J.Chin and K. Orzech, 2002, unpublished data). The organic-rich mud is interpreted as a tidal marsh deposit that pre-dates the present tidal marshes occurring in Suisun Bay.

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1614... shall comply with requirements concerning mud control, mud test and monitoring equipment, mud quantities...

Recycling red mud from the production of aluminium as a red cement-based mortar.

PubMed

Yang, Xiaojie; Zhao, Jianfeng; Li, Haoxin; Zhao, Piqi; Chen, Qin

2017-05-01

Current management for red mud is insufficient and a new method is needed. A series of experiments have been carried out to develop a new approach for effective management of red mud. Mortars without or with 3%, 6% and 9% red mud were prepared and their fresh and hardened properties were measured to access the possibility of recycling the red mud in the production of red cement-based mortar. The mechanisms corresponding to their mechanical performance variations were explored by X-ray powder diffraction and scanning electron microscopy. The results show that the fresh mortars with red mud present an increase of viscosity as compared with the control. However, little difference is found when the content of red mud is altered. It also can be seen that red mud increases flow time and reduces the slump flow of the mortar. Meanwhile, it is found that mortar with red mud is provided with higher air content. Red mud is eligible to adjust the decorative mortar colour. Compressive strength of mortar is improved when less than 6% red mud is added. However, overall it has a slightly negative effect on tensile bond strength. It decreases the Ca(OH) 2 content and densifies the microstructure of hardened paste. The heavy metal concentrations in leachates of mortars with red mud are much lower than the values required in the standard, and it will not do harm to people's health and the environment. These results are important to recycle and effectively manage red mud via the production of red cement-based mortar.

Linking geochemical processes in mud volcanoes with arsenic mobilization driven by organic matter.

PubMed

Liu, Chia-Chuan; Kar, Sandeep; Jean, Jiin-Shuh; Wang, Chung-Ho; Lee, Yao-Chang; Sracek, Ondra; Li, Zhaohui; Bundschuh, Jochen; Yang, Huai-Jen; Chen, Chien-Yen

2013-11-15

The present study deals with geochemical characterization of mud fluids and sediments collected from Kunshuiping (KSP), Liyushan (LYS), Wushanting (WST), Sinyangnyuhu (SYNH), Hsiaokunshui (HKS) and Yenshuikeng (YSK) mud volcanoes in southwestern Taiwan. Chemical constituents (cations, anions, trace elements, organic carbon, humic acid, and stable isotopes) in both fluids and mud were analyzed to investigate the geochemical processes and spatial variability among the mud volcanoes under consideration. Analytical results suggested that the anoxic mud volcanic fluids are highly saline, implying connate water as the probable source. The isotopic signature indicated that δ(18)O-rich fluids may be associated with silicate and carbonate mineral released through water-rock interaction, along with dehydration of clay minerals. Considerable amounts of arsenic in mud irrespective of fluid composition suggested possible release through biogeochemical processes in the subsurface environment. Sequential extraction of As from the mud indicated that As was mostly present in organic and sulphidic phases, and adsorbed on amorphous Mn oxyhydroxides. Volcanic mud and fluids are rich in organic matter (in terms of organic carbon), and the presence of humic acid in mud has implications for the binding of arsenic. Functional groups of humic acid also showed variable sources of organic matter among the mud volcanoes being examined. Because arsenate concentration in the mud fluids was found to be independent from geochemical factors, it was considered that organic matter may induce arsenic mobilization through an adsorption/desorption mechanism with humic substances under reducing conditions. Organic matter therefore plays a significant role in the mobility of arsenic in mud volcanoes. Copyright © 2012 Elsevier B.V. All rights reserved.