Processing of surrogate nuclear fuel pellets for better dimensional control with dry bag isostatic pressing

DOE PAGES

Hoggan, Rita E.; Zuck, Larry D.; Cannon, W. Roger; ...

2016-05-26

A study of improved methods of processing fuel pellets was undertaken using ceria and zirconia/yttria/alumina as surrogates. Through proper granulation and vertical vibration (tapping) of the parts bag prior to dry bag isostatic pressing (DBIP), reproducibility of diameter profiles among multiple pellets of ceria was improved by almost an order of magnitude. Reproducibility of sintered pellets was sufficiently good to possibly avoid grinding. Deviation from the mean diameter along the length of multiple pellets, as well as, deviation from roundness, decreased after sintering. This is not generally observed with dry pressed pellets. Thus it is possible to machine to tolerancemore » before sintering if grinding is necessary.« less

Microstructure of bentonite in iron ore green pellets.

PubMed

Bhuiyan, Iftekhar U; Mouzon, Johanne; Schröppel, Birgit; Kaech, Andres; Dobryden, Illia; Forsmo, Seija P E; Hedlund, Jonas

2014-02-01

Sodium-activated calcium bentonite is used as a binder in iron ore pellets and is known to increase strength of both wet and dry iron ore green pellets. In this article, the microstructure of bentonite in magnetite pellets is revealed for the first time using scanning electron microscopy. The microstructure of bentonite in wet and dry iron ore pellets, as well as in distilled water, was imaged by various imaging techniques (e.g., imaging at low voltage with monochromatic and decelerated beam or low loss backscattered electrons) and cryogenic methods (i.e., high pressure freezing and plunge freezing in liquid ethane). In wet iron ore green pellets, clay tactoids (stacks of parallel primary clay platelets) were very well dispersed and formed a voluminous network occupying the space available between mineral particles. When the pellet was dried, bentonite was drawn to the contact points between the particles and formed solid bridges, which impart strength to the solid compact.

mirRICH, a simple method to enrich the small RNA fraction from over-dried RNA pellets.

PubMed

Choi, Cheolwon; Yoon, Seulgi; Moon, Hyesu; Bae, Yun-Ui; Kim, Chae-Bin; Diskul-Na-Ayudthaya, Penchatr; Ngu, Trinh Van; Munir, Javaria; Han, JaeWook; Park, Se Bin; Moon, Jong-Seok; Song, Sujung; Ryu, Seongho

2018-04-11

Techniques to isolate the small RNA fraction (<200nt) by column-based methods are commercially available. However, their use is limited because of the relatively high cost. We found that large RNA molecules, including mRNAs and rRNAs, are aggregated together in the presence of salts when RNA pellets are over-dried. Moreover, once RNA pellets are over-dried, large RNA molecules are barely soluble again during the elution process, whereas small RNA molecules (<100nt) can be eluted. We therefore modified the acid guanidinium thiocyanate-phenol-chloroform (AGPC)-based RNA extraction protocol by skipping the 70% ethanol washing step and over-drying the RNA pellet for 1 hour at room temperature. We named this novel small RNA isolation method "mirRICH." The quality of the small RNA sequences was validated by electrophoresis, next-generation sequencing, and quantitative PCR, and the findings support that our newly developed column-free method can successfully and efficiently isolate small RNAs from over-dried RNA pellets.

Pelletizing lignite

DOEpatents

Goksel, Mehmet A.

1983-11-01

Lignite is formed into high strength pellets having a calorific value of at least 9,500 Btu/lb by blending a sufficient amount of an aqueous base bituminous emulsion with finely-divided raw lignite containing its inherent moisture to form a moistened green mixture containing at least 3 weight % of the bituminous material, based on the total dry weight of the solids, pelletizing the green mixture into discrete green pellets of a predetermined average diameter and drying the green pellets to a predetermined moisture content, preferrably no less than about 5 weight %. Lignite char and mixture of raw lignite and lignite char can be formed into high strength pellets in the same general manner.

The effect of pelleting on in situ rumen degradability of compound feed containing brown rice for dairy cows.

PubMed

Tagawa, Shin-Ichi; Yoshida, Norio; Iino, Yukihiro; Horiguchi, Ken-Ichi; Takahashi, Toshiyoshi; Watanabe, Maria; Takemura, Kei; Ito, Syuhei; Mikami, Toyoji

2017-01-01

This study was conducted to determine the effect of pelleting on in situ dry matter degradability of pelleted compound feed containing brown rice for dairy cows. Mash feed of the same composition was used as a control and the in situ study was conducted using three non-lactating Holstein steers fitted with a rumen cannula. The feeds contained 32.3% brown rice, 19.4% rapeseed meal, 11.4% wheat bran and 10.6% soybean meal (fresh weight basis). Except for moisture content, the chemical composition of the feed was not affected by pelleting. In situ dry matter disappearance of the feed increased from 0 to 2 h and after 72 h of incubation with pellet processing. Integration of the dry matter disappearance values over time revealed that degradability parameter a (soluble fraction) increased with pellet processing, whereas parameter b (potentially degradable fraction) decreased. Parameter c (fractional rate of degradation) and effective degradability (5% passage rate) were not affected by pellet processing. We concluded that pellet processing promotes rumen degradability at early incubation hours when the pelleted feed contains brown rice. © 2016 Japanese Society of Animal Science.

Particle fueling experiments with a series of pellets in LHD

NASA Astrophysics Data System (ADS)

Baldzuhn, J.; Damm, H.; Dinklage, A.; Sakamoto, R.; Motojima, G.; Yasuhara, R.; Ida, K.; Yamada, H.; LHD Experiment Group; Wendelstein 7-X Team

2018-03-01

Ice pellet injection is performed in the heliotron Large Helical Device (LHD). The pellets are injected in short series, with up to eight individual pellets. Parameter variations are performed for the pellet ice isotopes, the LHD magnetic configurations, the heating scenario, and some others. These experiments are performed in order to find out whether deeper fueling can be achieved with a series of pellets compared to single pellets. An increase of the fueling efficiency is expected since pre-cooling of the plasma by the first pellets within a series could aid deeper penetration of later pellets in the same series. In addition, these experiments show which boundary conditions must be fulfilled to optimize the technique. The high-field side injection of pellets, as proposed for deep fueling in a tokamak, will not be feasible with the same efficiency in a stellarator or heliotron because there the magnetic field gradient is smaller than in a tokamak of comparable size. Hence, too shallow pellet fueling, in particular in a large device or a fusion reactor, will be an issue that can be overcome only by extremely high pellet velocities, or other techniques that will have to be developed in the future. It turned out by our investigations that the fueling efficiency can be enhanced by the injection of a series of pellets to some extent. However, further investigations will be needed in order to optimize this approach for deep particle fueling.

Automated catalyst processing for cloud electrode fabrication for fuel cells

DOEpatents

Goller, Glen J.; Breault, Richard D.

1980-01-01

A process for making dry carbon/polytetrafluoroethylene floc material, particularly useful in the manufacture of fuel cell electrodes, comprises of the steps of floccing a co-suspension of carbon particles and polytetrafluoroethylene particles, filtering excess liquids from the co-suspension, molding pellet shapes from the remaining wet floc solids without using significant pressure during the molding, drying the wet floc pellet shapes within the mold at temperatures no greater than about 150.degree. F., and removing the dry pellets from the mold.

Durable regenerable sorbent pellets for removal of hydrogen sulfide from coal gas

DOEpatents

Siriwardane, R.V.

1999-02-02

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form, usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

Durable regenerable sorbent pellets for removal of hydrogen sulfide from coal gas

DOEpatents

Siriwardane, R.V.

1997-12-30

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

Durable regenerable sorbent pellets for removal of hydrogen sulfide from coal gas

DOEpatents

Siriwardane, Ranjani V.

1997-01-01

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

Durable regenerable sorbent pellets for removal of hydrogen sulfide coal gas

DOEpatents

Siriwardane, Ranjani V.

1999-01-01

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form, usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

A Novel Approach for Dry Powder Coating of Pellets with Ethylcellulose. Part II: Evaluation of Caffeine Release.

PubMed

Albertini, Beatrice; Melegari, Cecilia; Bertoni, Serena; Dolci, Luisa Stella; Passerini, Nadia

2018-04-01

The objective of this study was to assess the efficacy and the capability of a novel ethylcellulose-based dry-coating system to obtain prolonged and stable release profiles of caffeine-loaded pellets. Lauric and oleic acids at a suitable proportion were used to plasticize ethylcellulose. The effect of coating level, percentage of drug loading, inert core particle size, and composition of the coating formulation including the anti-sticking agent on the drug release profile were fully investigated. A coating level of 15% w/w was the maximum layered amount which could modify the drug release. The best controlled drug release was obtained by atomizing talc (2.5% w/w) together with the solid plasticizer during the dry powder-coating process. SEM pictures revealed a substantial drug re-crystallization on the pellet surface, and the release studies evidenced that caffeine diffused through the plasticized polymer acting as pore former. Therefore, the phenomenon of caffeine migration across the coating layer had a strong influence on the permeability of the coating membrane. Comparing dry powder-coated pellets to aqueous film-coated ones, drug migration happened during storage, though more sustained release profiles were obtained. The developed dry powder-coating process enabled the production of stable caffeine sustained release pellets. Surprisingly, the release properties of the dry-coated pellets were mainly influenced by the way of addition of talc into the dry powder-coating blend and by the drug nature and affinity to the coating components. It would be interesting to study the efficacy of novel coating system using a different API.

Synthesis of Self-Bonded Pellets of ETS-4 Phase by New Methodology of Preparation

NASA Astrophysics Data System (ADS)

De Luca, P.; Mastroianni, C.; Nagy, J. B.

2018-06-01

We hereby present the results of a research in order to prepare self-bonded pellets of ETS-4 phase by a new methodology of preparation. In particular, the pellets were prepared by kneading crystals of ETS-4 phase and a dry gel, the latter being the precursor for the synthesis of the ETS-4 phase crystals. One of the innovative aspects that is proposed and highlighted in this work is represented by the fact that the dry-gel acts as a “binder”. It is characterized by the same chemical composition of crystals, thus avoiding contamination with other elements. In addition, dry-gel allows, the promotion of nucleation phenomena and thus the formation of new crystals of ETS-4 during the pellets baking phases. The pellets were characterized by X-ray diffraction (XRD), Electron microscopy (SEM) and mechanical strength by hardness tester.

Impact of Sequential Ammonia Fiber Expansion (AFEX) Pretreatment and Pelletization on the Moisture Sorption Properties of Corn Stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonner, Ian J.; Thompson, David N.; Teymouri, Farzaneh

Combining ammonia fiber expansion (AFEX™) pretreatment with a depot processing facility is a promising option for delivering high-value densified biomass to the emerging bioenergy industry. However, because the pretreatment process results in a high moisture material unsuitable for pelleting or storage (40% wet basis), the biomass must be immediately dried. If AFEX pretreatment results in a material that is difficult to dry, the economics of this already costly operation would be at risk. This work tests the nature of moisture sorption isotherms and thin-layer drying behavior of corn (Zea mays L.) stover at 20°C to 60°C before and after sequentialmore » AFEX pretreatment and pelletization to determine whether any negative impacts to material drying or storage may result from the AFEX process. The equilibrium moisture content to equilibrium relative humidity relationship for each of the materials was determined using dynamic vapor sorption isotherms and modeled with modified Chung-Pfost, modified Halsey, and modified Henderson temperature-dependent models as well as the Double Log Polynomial (DLP), Peleg, and Guggenheim Anderson de Boer (GAB) temperature-independent models. Drying kinetics were quantified under thin-layer laboratory testing and modeled using the Modified Page's equation. Water activity isotherms for non-pelleted biomass were best modeled with the Peleg temperature-independent equation while isotherms for the pelleted biomass were best modeled with the Double Log Polynomial equation. Thin-layer drying results were accurately modeled with the Modified Page's equation. The results of this work indicate that AFEX pretreatment results in drying properties more favorable than or equal to that of raw corn stover, and pellets of superior physical stability in storage.« less

Lignite pellets and methods of agglomerating or pelletizing

DOEpatents

Baker, Albert F.; Blaustein, Eric W.; Deurbrouck, Albert W.; Garvin, John P.; McKeever, Robert E.

1981-01-01

The specification discloses lignite pellets which are relatively hard, dust resistant, of generally uniform size and free from spontaneous ignition and general degradation. Also disclosed are methods for making such pellets which involve crushing as mined lignite, mixing said lignite with a binder such as asphalt, forming the lignite binder mixture into pellets, and drying the pellets.

46 CFR 148.245 - Direct reduced iron (DRI); lumps, pellets, and cold-molded briquettes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... another during periods of rain or snow. (e) DRI lumps, pellets, or cold-molded briquettes may not be... percent hydrogen, by volume, is maintained throughout the voyage in any hold containing these materials...

NIR techniques create added values for the pellet and biofuel industry.

PubMed

Lestander, Torbjörn A; Johnsson, Bo; Grothage, Morgan

2009-02-01

A 2(3)-factorial experiment was carried out in an industrial plant producing biofuel pellets with sawdust as feedstock. The aim was to use on-line near infrared (NIR) spectra from sawdust for real time predictions of moisture content, blends of sawdust and energy consumption of the pellet press. The factors varied were: drying temperature and wood powder dryness in binary blends of sawdust from Norway spruce and Scots pine. The main results were excellent NIR calibration models for on-line prediction of moisture content and binary blends of sawdust from the two species, but also for the novel finding that the consumption of electrical energy per unit pelletized biomass can be predicted by NIR reflectance spectra from sawdust entering the pellet press. This power consumption model, explaining 91.0% of the variation, indicated that NIR data contained information of the compression and friction properties of the biomass feedstock. The moisture content model was validated using a running NIR calibration model in the pellet plant. It is shown that the adjusted prediction error was 0.41% moisture content for grinded sawdust dried to ca. 6-12% moisture content. Further, although used drying temperatures influenced NIR spectra the models for drying temperature resulted in low prediction accuracy. The results show that on-line NIR can be used as an important tool in the monitoring and control of the pelletizing process and that the use of NIR technique in fuel pellet production has possibilities to better meet customer specifications, and therefore create added production values.

Characteristics, atmospheric drivers and occurrence patterns of freezing precipitation and ice pellets over the Prairie Provinces and Arctic Territories of Canada: 1964-2005

NASA Astrophysics Data System (ADS)

Kochtubajda, Bohdan; Mooney, Curtis; Stewart, Ronald

2017-07-01

Freezing precipitation and ice pellet events on the Canadian Prairies and Arctic territories of Canada often lead to major disruptions to air and ground transportation, damage power grids and prevent arctic caribou and other animals from accessing the plants and lichen they depend on for survival. In a warming climate, these hazards and associated impacts will continue to happen, although their spatial and temporal characteristics may vary. In order to address these issues, the occurrence of freezing rain, freezing drizzle, and ice pellets from 1964 to 2005 is examined using hourly weather observations at 27 manned 24 h weather stations across the different climatic regions of the Prairie Provinces and Arctic Territories of Canada. Because of the enormous size of the area and its diverse climatic regions, many temporal and spatial differences in freezing precipitation and ice pellet characteristics occur. The 12 most widespread freezing rain events over the study area are associated with only two atmospheric patterns with one linked to strong warm advection between low and high pressure centres and the other pattern associated with chinooks occurring east of the Rocky Mountains. Given the annual patterns of freezing rain occurrence found in this study, it is proposed that a maximum of five regimes exist and three occur within the Prairies and Arctic.

Impact of ammonia fiber expansion (AFEX) pretreatment on energy consumption during drying, grinding, and pelletization of corn stover

DOE PAGES

Bonner, Ian Jeffery; Thompson, David N.; Plummer, Mitchell; ...

2016-01-08

Pretreatment and densification of biomass can increase the viability of bioenergy production by providing a feedstock that is readily hydrolyzed and able to be transported greater distances. Ammonia Fiber Expansion (AFEX) is one such method targeted for use at distributed depots to create a value-added and densified feedstock for bioenergy use. However, the pretreatment process results in a high-moisture material that must be dried, further size reduced, and pelletized; all of which are energy intensive processes. This work quantifies the energy consumption required to dry, grind, and densify AFEX pretreated corn stover compared to non-pretreated stover and explores the potentialmore » of reduced drying as a means to conserve energy. The purpose of this work is to understand whether material property changes resulting from AFEX pretreatment influence the material performance in downstream formatting operations. Material properties, heat balance equations, and a rotary drum dryer model were used to model a commercial scale rotary drum dryer for AFEX pretreated corn stover, showing the potential to reduce dryer energy consumption by up to 36% compared to non-pretreated corn stover. Laboratory measured grinding and pelleting energies were both very sensitive to material moisture content. Overall, the total energy required for drying, grinding, and pelleting amounts to a savings of up to 20 kWh/dry ton for the AFEX pretreated material when dried to a low moisture content, equating to up to 0.55 /kg savings for gas and electricity. Grinding and pelleting of high moisture AFEX pretreated stover was shown to be more costly than the savings collected through reduced drying. Furthermore, while the energy and cost savings shown here are modest, the results help to highlight operational challenges and opportunities for continued improvement.« less

Impact of ammonia fiber expansion (AFEX) pretreatment on energy consumption during drying, grinding, and pelletization of corn stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonner, Ian Jeffery; Thompson, David N.; Plummer, Mitchell

Pretreatment and densification of biomass can increase the viability of bioenergy production by providing a feedstock that is readily hydrolyzed and able to be transported greater distances. Ammonia Fiber Expansion (AFEX) is one such method targeted for use at distributed depots to create a value-added and densified feedstock for bioenergy use. However, the pretreatment process results in a high-moisture material that must be dried, further size reduced, and pelletized; all of which are energy intensive processes. This work quantifies the energy consumption required to dry, grind, and densify AFEX pretreated corn stover compared to non-pretreated stover and explores the potentialmore » of reduced drying as a means to conserve energy. The purpose of this work is to understand whether material property changes resulting from AFEX pretreatment influence the material performance in downstream formatting operations. Material properties, heat balance equations, and a rotary drum dryer model were used to model a commercial scale rotary drum dryer for AFEX pretreated corn stover, showing the potential to reduce dryer energy consumption by up to 36% compared to non-pretreated corn stover. Laboratory measured grinding and pelleting energies were both very sensitive to material moisture content. Overall, the total energy required for drying, grinding, and pelleting amounts to a savings of up to 20 kWh/dry ton for the AFEX pretreated material when dried to a low moisture content, equating to up to 0.55 /kg savings for gas and electricity. Grinding and pelleting of high moisture AFEX pretreated stover was shown to be more costly than the savings collected through reduced drying. Furthermore, while the energy and cost savings shown here are modest, the results help to highlight operational challenges and opportunities for continued improvement.« less

Resource recovery of organic sludge as refuse derived fuel by fry-drying process.

PubMed

Chang, Fang-Chih; Ko, Chun-Han; Wu, Jun-Yi; Wang, H Paul; Chen, Wei-Sheng

2013-08-01

The organic sludge and waste oil were collected from the industries of thin film transistor liquid crystal display and the recycled cooking oil. The mixing ratio of waste cooking oil and organic sludge, fry-drying temperatures, fry-drying time, and the characteristics of the organic sludge pellet grain were investigated. After the fry-drying process, the moisture content of the organic sludge pellet grain was lower than 5% within 25 min and waste cooking oil was absorbed on the dry solid. The fry-drying organic sludge pellet grain was easy to handle and odor free. Additionally, it had a higher calorific value than the derived fuel standards and could be processed into organic sludge derived fuels. Thus, the granulation and fry-drying processes of organic sludge with waste cooking oil not only improves the calorific value of organic sludge and becomes more valuable for energy recovery, but also achieves waste material disposal and cost reduction. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of process variables on the quality characteristics of pelleted wheat distiller's dried grains with solubles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaya Shankar Tumuluru; Lope Tabil; Anthony Opoku

2011-04-01

The rapid expansion of ethanol processing plants in Canada has resulted in a significant increase in the production of wheat-based distiller's dried grains with solubles (DDGS). Transportation and flowability problems associated with DDGS necessitate investigations on pelleting. In the present study, the effect of process variables like die temperature (T) and feed moisture content (Mw) on the pellet properties like pellet moisture content, durability and pellet density was explored using a single pelleting machine; further studies on pelleting DDGS using a pilot-scale pellet mill were also conducted to understand the effect of die diameter and steam conditioning on durability andmore » bulk density of pellets. Proximate analysis of DDGS indicated that crude protein and dry matter were in the range of 37.37–40.33% and 91.27–92.60%, respectively. Linear regression models developed for pellet quality attributes like pellet moisture content, pellet density and durability adequately described the single pelleting process with R2 value of 0.97, 0.99 and 0.7, respectively. ANOVA results have indicated that linear terms T and Mw and the interaction term T × Mw were statistically significant at P < 0.01 and P < 0.1 for pellet moisture content and pellet density. Based on the trends of the surface plots, a medium T of about 50–80 °C and a low Mw of about 5.1% resulted in maximum pellet density and durability and minimum pellet moisture content. Results from pilot-scale studies indicated that bulk density, durability and throughput values were 436.8–528.9 kg m-3, 60.3–92.7% and 45.52–68.77 kg h-1, respectively. It was observed that both die diameter and steam addition had a significant effect on the bulk density and the durability values. The highest bulk density and durability were achieved with 6.4 mm die diameter with steam addition compared to 7.9 mm die with or without steam addition.« less

Influence of grass pellet production on pyrrolizidine alkaloids occurring in Senecio aquaticus-infested grassland.

PubMed

Gottschalk, Christoph; Ostertag, Johannes; Meyer, Karsten; Gehring, Klaus; Thyssen, Stefan; Gareis, Manfred

2018-04-01

1,2-Dehydro-pyrrolizidine alkaloids (PA) and their N-oxides (PANO) exhibit acute and chronic toxic effects on the liver and other organs and therefore are a hazard for animal and human health. In certain regions of Germany, an increasing spread of Senecio spp. (ragwort) on grassland and farmland areas has been observed during the last years leading to a PA/PANO-contamination of feed and food of animal and plant origin. This project was carried out to elucidate whether the process of grass pellet production applying hot air drying influences the content of PA and PANO. Samples of hay (n = 22) and grass pellets (n = 28) originated from naturally infested grassland (around 10% and 30% dominance of Senecio aquaticus) and from a trial plot with around 50% dominance. Grass pellets were prepared from grass originating from exactly the same plots as the hay samples. The samples were analysed by liquid chromatography-tandem mass spectrometry for PA/PANO typically produced by this weed. The results of the study revealed that PA/PANO levels (predominantly sum of senecionine, seneciphylline, erucifoline and their N-oxides) in hay ranged between 2.1 and 12.6 mg kg -1 dry matter in samples with 10% and 30% dominance of S. aquaticus, respectively. Samples from the trial plot (50% dominance) had levels of up to 52.9 mg kg -1 . Notably, the hot air drying process during the production of grass pellets did not lead to a reduction of PA/PANO levels. Instead, the levels in grass pellets with 10% and 30% S. aquaticus ranged from 3.1 to 55.1 mg kg -1 . Grass pellets from the trial plot contained up to 96.8 mg kg -1 . In conclusion, hot air drying and grass pellet production did not affect PA/PANO contents in plant material and therefore, heat-dried products cannot be regarded as safe in view of the toxic potential of 1,2-dehydro-pyrrolizidine alkaloids.

49 CFR 175.900 - Handling requirements for carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2010 CFR

2010-10-01

... (dry ice). 175.900 Section 175.900 Transportation Other Regulations Relating to Transportation PIPELINE....900 Handling requirements for carbon dioxide, solid (dry ice). Carbon dioxide, solid (dry ice) when... operator must ensure that the ground staff is informed that the dry ice is being loaded or is on board the...

49 CFR 175.900 - Handling requirements for carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2013 CFR

2013-10-01

... (dry ice). 175.900 Section 175.900 Transportation Other Regulations Relating to Transportation PIPELINE....900 Handling requirements for carbon dioxide, solid (dry ice). Carbon dioxide, solid (dry ice) when... operator must ensure that the ground staff is informed that the dry ice is being loaded or is on board the...

49 CFR 175.900 - Handling requirements for carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2012 CFR

2012-10-01

... (dry ice). 175.900 Section 175.900 Transportation Other Regulations Relating to Transportation PIPELINE....900 Handling requirements for carbon dioxide, solid (dry ice). Carbon dioxide, solid (dry ice) when... operator must ensure that the ground staff is informed that the dry ice is being loaded or is on board the...

49 CFR 175.900 - Handling requirements for carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2011 CFR

2011-10-01

... (dry ice). 175.900 Section 175.900 Transportation Other Regulations Relating to Transportation PIPELINE....900 Handling requirements for carbon dioxide, solid (dry ice). Carbon dioxide, solid (dry ice) when... operator must ensure that the ground staff is informed that the dry ice is being loaded or is on board the...

49 CFR 175.900 - Handling requirements for carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2014 CFR

2014-10-01

... (dry ice). 175.900 Section 175.900 Transportation Other Regulations Relating to Transportation PIPELINE....900 Handling requirements for carbon dioxide, solid (dry ice). Carbon dioxide, solid (dry ice) when... operator must ensure that the ground staff is informed that the dry ice is being loaded or is on board the...

Influence of apple pomace inclusion on the process of animal feed pelleting.

PubMed

Maslovarić, Marijana D; Vukmirović, Đuro; Pezo, Lato; Čolović, Radmilo; Jovanović, Rade; Spasevski, Nedeljka; Tolimir, Nataša

2017-08-01

Apple pomace (AP) is the main by-product of apple juice production. Large amounts of this material disposed into landfills can cause serious environmental problems. One of the solutions is to utilise AP as animal feed. The aim of this study was to investigate the impact of dried AP inclusion into model mixtures made from conventional feedstuffs on pellet quality and pellet press performance. Three model mixtures, with different ratios of maize, sunflower meal and AP, were pelleted. Response surface methodology (RSM) was applied when designing the experiment. The simultaneous and interactive effects of apple pomace share (APS) in the mixtures, die thickness (DT) of the pellet press and initial moisture content of the mixtures (M), on pellet quality and production parameters were investigated. Principal component analysis (PCA) and standard score (SS) analysis were applied for comprehensive analysis of the experimental data. The increase in APS led to an improvement of pellet quality parameters: pellet durability index (PDI), hardness (H) and proportion of fines in pellets. The increase in DT and M resulted in pellet quality improvement. The increase in DT and APS resulted in higher energy consumption of the pellet press. APS was the most influential variable for PDI and H calculation, while APS and DT were the most influential variables in the calculation of pellet press energy consumption. PCA showed that the first two principal components could be considered sufficient for data representation. In conclusion, addition of dried AP to feed model mixtures significantly improved the quality of the pellets.

49 CFR 173.217 - Carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Carbon dioxide, solid (dry ice). 173.217 Section... Class 7 § 173.217 Carbon dioxide, solid (dry ice). (a) Carbon dioxide, solid (dry ice), when offered for... marked on two sides “WARNING CO2 SOLID (DRY ICE).” (2) Other packagings containing solid carbon dioxide...

49 CFR 173.217 - Carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 2 2012-10-01 2012-10-01 false Carbon dioxide, solid (dry ice). 173.217 Section... Class 7 § 173.217 Carbon dioxide, solid (dry ice). (a) Carbon dioxide, solid (dry ice), when offered for... marked on two sides “WARNING CO2 SOLID (DRY ICE).” (2) Other packagings containing solid carbon dioxide...

49 CFR 173.217 - Carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Carbon dioxide, solid (dry ice). 173.217 Section... Class 7 § 173.217 Carbon dioxide, solid (dry ice). (a) Carbon dioxide, solid (dry ice), when offered for... marked on two sides “WARNING CO2 SOLID (DRY ICE).” (2) Other packagings containing solid carbon dioxide...

49 CFR 173.217 - Carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 2 2014-10-01 2014-10-01 false Carbon dioxide, solid (dry ice). 173.217 Section... Class 7 § 173.217 Carbon dioxide, solid (dry ice). (a) Carbon dioxide, solid (dry ice), when offered for... marked on two sides “WARNING CO2 SOLID (DRY ICE).” (2) Other packagings containing solid carbon dioxide...

49 CFR 173.217 - Carbon dioxide, solid (dry ice).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 2 2013-10-01 2013-10-01 false Carbon dioxide, solid (dry ice). 173.217 Section... Class 7 § 173.217 Carbon dioxide, solid (dry ice). (a) Carbon dioxide, solid (dry ice), when offered for... marked on two sides “WARNING CO2 SOLID (DRY ICE).” (2) Other packagings containing solid carbon dioxide...

Pellet injection technology

NASA Astrophysics Data System (ADS)

Combs, S. K.

1993-07-01

During the last 10 to 15 years, significant progress has been made worldwide in the area of pellet injection technology. This specialized field of research originated as a possible solution to the problem of depositing atoms of fuel deep within magnetically confined, hot plasmas for refueling of fusion power reactors. Using pellet injection systems, frozen macroscopic (millimeter-size) pellets composed of the isotopes of hydrogen are formed, accelerated, and transported to the plasma for fueling. The process and benefits of plasma fueling by this approach have been demonstrated conclusively on a number of toroidal magnetic confinement configurations; consequently, pellet injection is the leading technology for deep fueling of magnetically confined plasmas for controlled thermonuclear fusion research. Hydrogen pellet injection devices operate at very low temperatures (≂10 K) at which solid hydrogen ice can be formed and sustained. Most injectors use conventional pneumatic (light gas gun) or centrifuge (mechanical) acceleration concepts to inject hydrogen or deuterium pellets at speeds of ≂1-2 km/s. Pellet injectors that can operate at quasi-steady state (pellet delivery rates of 1-40 Hz) have been developed for long-pulse fueling. The design and operation of injectors with the heaviest hydrogen isotope, tritium, offer some special problems because of tritium's radioactivity. To address these problems, a proof-of-principle experiment was carried out in which tritium pellets were formed and accelerated to speeds of 1.4 km/s. Tritium pellet injection is scheduled on major fusion research devices within the next few years. Several advanced accelerator concepts are under development to increase the pellet velocity. One of these is the two-stage light gas gun, for which speeds of slightly over 4 km/s have already been reported in laboratory experiments with deuterium ice. A few two-stage pneumatic systems (single-shot) have recently been installed on tokamak experiments. This article reviews the equipment and instruments that have been developed for pellet injection with emphasis on recent advances. Prospects for future development are addressed, as are possible applications of this technology to other areas of research.

Influence of Wheat Straw Pelletizing and Inclusion Rate in Dry Rolled or Steam-flaked Corn-based Finishing Diets on Characteristics of Digestion for Feedlot Cattle.

PubMed

Manríquez, O M; Montano, M F; Calderon, J F; Valdez, J A; Chirino, J O; Gonzalez, V M; Salinas-Chavira, J; Mendoza, G D; Soto, S; Zinn, R A

2016-06-01

Eight Holstein steers (216±48 kg body weight) fitted with ruminal and duodenal cannulas were used to evaluate effects of wheat straw processing (ground vs pelleted) at two straw inclusion rates (7% and 14%; dry matter basis) in dry rolled or steam-flaked corn-based finishing diets on characteristics of digestion. The experimental design was a split plot consisting of two simultaneous 4×4 Latin squares. Increasing straw level reduced ruminal (p<0.01) and total tract (p = 0.03) organic matter (OM) digestion. As expected, increasing wheat straw level from 7% to 14% decreased (p<0.05) ruminal and total tract digestion of OM. Digestion of neutral detergent fiber (NDF) and starch, per se, were not affected (p>0.10) by wheat straw level. Likewise, straw level did not influence ruminal acetate and propionate molar proportions or estimated methane production (p>0.10). Pelleting straw did not affect (p≥0.48) ruminal digestion of OM, NDF, and starch, or microbial efficiency. Ruminal feed N digestion was greater (7.4%; p = 0.02) for ground than for pelleted wheat straw diets. Although ruminal starch digestion was not affected by straw processing, post-ruminal (p<0.01), and total-tract starch (p = 0.05) digestion were greater for ground than for pelleted wheat straw diets, resulting in a tendency for increased post-ruminal (p = 0.06) and total tract (p = 0.07) OM digestion. Pelleting wheat straw decreased (p<0.01) ruminal pH, although ruminal volatile fatty acids (VFA) concentration and estimated methane were not affected (p≥0.27). Ruminal digestion of OM and starch, and post-ruminal and total tract digestion of OM, starch and N were greater (p<0.01) for steam-flaked than for dry rolled corn-based diets. Ruminal NDF digestion was greater (p = 0.02) for dry rolled than for steam-flaked corn, although total tract NDF digestion was unaffected (p = 0.94). Ruminal microbial efficiency and ruminal degradation of feed N were not affected (p>0.14) by corn processing. However, microbial N flow to the small intestine and ruminal N efficiency (non-ammonia N flow to the small intestine/N intake) were greater (p<0.01) for steam-flaked than for dry rolled corn-based diets. Ruminal pH and total VFA concentration were not affected (p≥ 0.16) by corn processing method. Compared with dry rolled corn, steam-flaked corn-based diets resulted in decreased acetate:propionate molar ratio (p = 0.02). It is concluded that at 7% or 14% straw inclusion rate, changes in physical characteristics of wheat straw brought about by pelleting negatively impact OM digestion of both steam-flaked and dry-rolled corn-based finishing diets. This effect is due to decreased post-ruminal starch digestion. Replacement of ground straw with pelleted straw also may decrease ruminal pH.

Formulating food protein-stabilized indomethacin nanosuspensions into pellets by fluid-bed coating technology: physical characterization, redispersibility, and dissolution.

PubMed

He, Wei; Lu, Yi; Qi, Jianping; Chen, Lingyun; Yin, Lifang; Wu, Wei

2013-01-01

Drug nanosuspensions are very promising for enhancing the dissolution and bioavailability of drugs that are poorly soluble in water. However, the poor stability of nanosuspensions, reflected in particle growth, aggregation/agglomeration, and change in crystallinity state greatly limits their applications. Solidification of nanosuspensions is an ideal strategy for addressing this problem. Hence, the present work aimed to convert drug nanosuspensions into pellets using fluid-bed coating technology. Indomethacin nanosuspensions were prepared by the precipitation-ultrasonication method using food proteins (soybean protein isolate, whey protein isolate, β-lactoglobulin) as stabilizers. Dried nanosuspensions were prepared by coating the nanosuspensions onto pellets. The redispersibility, drug dissolution, solid-state forms, and morphology of the dried nanosuspensions were evaluated. The mean particle size for the nanosuspensions stabilized using soybean protein isolate, whey protein isolate, and β-lactoglobulin was 588 nm, 320 nm, and 243 nm, respectively. The nanosuspensions could be successfully layered onto pellets with high coating efficiency. Both the dried nanosuspensions and nanosuspensions in their original amorphous state and not influenced by the fluid-bed coating drying process could be redispersed in water, maintaining their original particle size and size distribution. Both the dried nanosuspensions and the original drug nanosuspensions showed similar dissolution profiles, which were both much faster than that of the raw crystals. Fluid-bed coating technology has potential for use in the solidification of drug nanosuspensions.

Durable zinc ferrite sorbent pellets for hot coal gas desulfurization

DOEpatents

Jha, Mahesh C.; Blandon, Antonio E.; Hepworth, Malcolm T.

1988-01-01

Durable, porous sulfur sorbents useful in removing hydrogen sulfide from hot coal gas are prepared by water pelletizing a mixture of fine zinc oxide and fine iron oxide with inorganic and organic binders and small amounts of activators such as sodium carbonate and molybdenite; the pellets are dried and then indurated at a high temperature, e.g., 1800.degree. C., for a time sufficient to produce crush-resistant pellets.

Pyrolysis of ground pine chip and ground pellet particles

DOE PAGES

Rezaei, Hamid; Yazdanpanah, Fahimeh; Lim, C. Jim; ...

2016-08-04

In addition to particle size, biomass density influences heat and mass transfer rates during the thermal treatment processes. In this research, thermal behaviour of ground pine chip particles and ground pine pellet particles in the range of 0.25–5 mm was investigated. A single particle from ground pellets was almost 3 to 4 times denser than a single particle from ground chips at a similar size and volume of particle. Temperature was ramped up from room temperature (~25 °C) to 600 °C with heating rates of 10, 20, 30, and 50 °C/min. Pellet particles took 25–88 % longer time to drymore » than the chip particles. Microscopic examination of 3 mm and larger chip particles showed cracks during drying. No cracks were observed for pellet particles. The mass loss due to treatment at temperatures higher than 200 °C was about 80% both for chip and pellet particles. It took 4 min for chip and pellet particles to lose roughly 63% of their dry mass at a heating rate of 50 °C/min. The SEM structural analysis showed enlarged pores and cracks in cell walls of the pyrolyzed wood chips. As a result, these pores were not observed in pyrolyzed pellet particles.« less

Robust Immobilized Amine CO 2 Sorbent Pellets Utilizing a Poly(Chloroprene) Polymer Binder and Fly Ash Additive

DOE PAGES

Wilfong, Walter Christopher; Kail, Brian W.; Howard, Bret H.; ...

2016-08-04

Pelletization of ca. 50 wt % amine/silica carbon dioxide sorbents was achieved with the novel combination of fly ash (FA) as a strength additive and hydrophobic poly(chloroprene) (PC) as a binder. The PC content and overall synthesis procedure of these materials were optimized to produce pellets, labeled as FA/E100-S_(20/80)_12.2, with the highest ball-mill attrition resistance (<0.5 wt % by fines, 24 h) and maximum CO 2 capture capacity of 1.78 mmol CO 2 g -1. The strength of the pellets was attributed to hydrogen-bonding of the relatively homogeneous PC network with the interlocked FA and BIAS particles (DRIFTS, SEM-EDS). Themore » low degradation of 3–4 % in the pellet's CO 2 capture capacity under both dry TGA (7.5 h) and practical fixed-bed (6.5 h dry; 4.5 h humid,≈5 vol % H 2O) CO 2 adsorption–desorption conditions highlights the pellet's excellent cyclic stability. These robust pellet characteristics make PC/FA/sorbent materials promising for commercial scale, point-source CO 2 capture.« less

Formulating food protein-stabilized indomethacin nanosuspensions into pellets by fluid-bed coating technology: physical characterization, redispersibility, and dissolution

PubMed Central

He, Wei; Lu, Yi; Qi, Jianping; Chen, Lingyun; Yin, Lifang; Wu, Wei

2013-01-01

Background Drug nanosuspensions are very promising for enhancing the dissolution and bioavailability of drugs that are poorly soluble in water. However, the poor stability of nanosuspensions, reflected in particle growth, aggregation/agglomeration, and change in crystallinity state greatly limits their applications. Solidification of nanosuspensions is an ideal strategy for addressing this problem. Hence, the present work aimed to convert drug nanosuspensions into pellets using fluid-bed coating technology. Methods Indomethacin nanosuspensions were prepared by the precipitation-ultrasonication method using food proteins (soybean protein isolate, whey protein isolate, β-lactoglobulin) as stabilizers. Dried nanosuspensions were prepared by coating the nanosuspensions onto pellets. The redispersibility, drug dissolution, solid-state forms, and morphology of the dried nanosuspensions were evaluated. Results The mean particle size for the nanosuspensions stabilized using soybean protein isolate, whey protein isolate, and β-lactoglobulin was 588 nm, 320 nm, and 243 nm, respectively. The nanosuspensions could be successfully layered onto pellets with high coating efficiency. Both the dried nanosuspensions and nanosuspensions in their original amorphous state and not influenced by the fluid-bed coating drying process could be redispersed in water, maintaining their original particle size and size distribution. Both the dried nanosuspensions and the original drug nanosuspensions showed similar dissolution profiles, which were both much faster than that of the raw crystals. Conclusion Fluid-bed coating technology has potential for use in the solidification of drug nanosuspensions. PMID:23983465

Four-Dimensional Weather Functional Requirements for NextGen Air Traffic Management

DTIC Science & Technology

2008-01-18

receive or contain. Acquire To come into the possession of something concrete or abstract. Analyze To examine carefully and in detail so as to...consisting of transparent or translucent pellets of ice (5 mm or less in diameter). Icing Formation of ice, rime, or hoarfrost on an aircraft. Impact...Can be observed and reported at the surface or aloft. Snow Type of frozen (or mostly frozen) precipitation composed of white or translucent ice

Use of a Tea Infuser to Submerge Low-Density Dry Ice

ERIC Educational Resources Information Center

Fictorie, Carl P.; Vitz, Ed

2004-01-01

A simple tea infuser is obtained and been used as a container for the dry ice to simulate the effect from high-density dry ice. The tea infuser is a simple, low cost device to allow instructors with access to dry ice makers to effectively use the interesting demonstration.

Durable zinc oxide-containing sorbents for coal gas desulfurization

DOEpatents

Siriwardane, Ranjani V.

1996-01-01

Durable zinc-oxide containing sorbent pellets for removing hydrogen sulfide from a gas stream at an elevated temperature are made up to contain titania as a diluent, high-surface-area silica gel, and a binder. These materials are mixed, moistened, and formed into pellets, which are then dried and calcined. The resulting pellets undergo repeated cycles of sulfidation and regeneration without loss of reactivity and without mechanical degradation. Regeneration of the pellets is carried out by contacting the bed with an oxidizing gas mixture.

Controlled ice nucleation in the field of freeze-drying: fundamentals and technology review.

PubMed

Geidobler, R; Winter, G

2013-10-01

In the scientific community as well as in commercial freeze-drying, controlled ice nucleation has received a lot of attention because increasing the ice nucleation temperature can significantly reduce primary drying duration. Furthermore, controlled ice nucleation enables to reduce the randomness of the ice nucleation temperature, which can be a serious scale-up issue during process development. In this review, fundamentals of ice nucleation in the field of freeze-drying are presented. Furthermore, the impact of controlled ice nucleation on product qualities is discussed, and methods to achieve controlled ice nucleation are presented. Copyright © 2013 Elsevier B.V. All rights reserved.

Method to produce durable pellets at lower energy consumption using high moisture corn stover and a corn starch binder in a flat die pellet mill

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tumuluru, Jaya Shankar; Conner, Craig C.; Hoover, Amber N.

Biomass from plants can serve as an alternative renewable energy resources for energy production. Low densities of 40–60 kg/m3 for ground lignocellulosic biomass like corn stover limit its operation for energy purposes. The common drawbacks are inefficient transportation, a bigger storage foot print, and handling problems. Densification of biomass using pellet mill helps to overcome these limitations. This study helps to understand the effect of binder on high moisture biomass with a focus on the quality (density and durability), the pelleting efficiency and the specific energy consumption of its pelleting process. Raw corn stover was pelleted at high moisture ofmore » 33% (w.b.) at both varying preheating temperatures and binder percentage. The die speed of the pellet mill was set at 60Hz. The pellets produced were analyzed and showed higher moisture content. They were further dried in a laboratory oven at 70°C for 3-4 hr bringing the pellet moisture to <9%. The dried pellets were evaluated for their physical properties like unit, bulk and tapped density, and durability. Furthermore, the results indicated increasing the binder percentage to 4% improved the physical properties of the pellets and reduced the specific energy consumption. Higher binder addition of 4% reduced the feedstock moisture loss during pelleting to <4%, which can be due reduced residence time of the material in the die. On the other hand the physical properties like density and durability improved significantly with binder addition. At 4% binder and 33% feedstock moisture content, the bulk density and durability values observed were >510 kg/m3 and >98% and the percent fines generation has reduced to <3%. Also at these conditions the specific energy consumption was reduced by about 30-40% compared no binder pelleting test.« less

Method to produce durable pellets at lower energy consumption using high moisture corn stover and a corn starch binder in a flat die pellet mill

DOE PAGES

Tumuluru, Jaya Shankar; Conner, Craig C.; Hoover, Amber N.

2016-06-15

Biomass from plants can serve as an alternative renewable energy resources for energy production. Low densities of 40–60 kg/m3 for ground lignocellulosic biomass like corn stover limit its operation for energy purposes. The common drawbacks are inefficient transportation, a bigger storage foot print, and handling problems. Densification of biomass using pellet mill helps to overcome these limitations. This study helps to understand the effect of binder on high moisture biomass with a focus on the quality (density and durability), the pelleting efficiency and the specific energy consumption of its pelleting process. Raw corn stover was pelleted at high moisture ofmore » 33% (w.b.) at both varying preheating temperatures and binder percentage. The die speed of the pellet mill was set at 60Hz. The pellets produced were analyzed and showed higher moisture content. They were further dried in a laboratory oven at 70°C for 3-4 hr bringing the pellet moisture to <9%. The dried pellets were evaluated for their physical properties like unit, bulk and tapped density, and durability. Furthermore, the results indicated increasing the binder percentage to 4% improved the physical properties of the pellets and reduced the specific energy consumption. Higher binder addition of 4% reduced the feedstock moisture loss during pelleting to <4%, which can be due reduced residence time of the material in the die. On the other hand the physical properties like density and durability improved significantly with binder addition. At 4% binder and 33% feedstock moisture content, the bulk density and durability values observed were >510 kg/m3 and >98% and the percent fines generation has reduced to <3%. Also at these conditions the specific energy consumption was reduced by about 30-40% compared no binder pelleting test.« less

Impact of RNA Degradation on Viral Diagnosis: An Understated but Essential Step for the Successful Establishment of a Diagnosis Network

PubMed Central

Relova, Damarys; Acevedo, Ana M.; Coronado, Liani; Perera, Carmen L.

2018-01-01

The current global conditions, which include intensive globalization, climate changes, and viral evolution among other factors, have led to an increased emergence of viruses and new viral diseases; RNA viruses are key drivers of this evolution. Laboratory networks that are linked to central reference laboratories are required to conduct both active and passive environmental surveillance of this complicated global viral environment. These tasks require a continuous exchange of strains or field samples between different diagnostic laboratories. The shipment of these samples on dry ice represents both a biological hazard and a general health risk. Moreover, the requirement to ship on dry ice could be hampered by high costs, particularly in underdeveloped countries or regions located far from each other. To solve these issues, the shipment of RNA isolated from viral suspensions or directly from field samples could be a useful way to share viral genetic material. However, extracted RNA stored in aqueous solutions, even at −70 °C, is highly prone to degradation. The current study evaluated different RNA storage conditions for safety and feasibility for future use in molecular diagnostics. The in vitro RNA-transcripts obtained from an inactivated highly pathogenic avian influenza (HPAI) H5N1 virus was used as a model. The role of secondary structures in the protection of the RNA was also explored. Of the conditions evaluated, the dry pellet matrix was best able to protect viral RNA under extreme storage conditions. This method is safe, cost-effective and assures the integrity of RNA samples for reliable molecular diagnosis. This study aligns with the globally significant “Global One Health” paradigm, especially with respect to the diagnosis of emerging diseases that require confirmation by reference laboratories. PMID:29415432

Interactions between barley grain processing and source of supplemental dietary fat on nitrogen metabolism and urea-nitrogen recycling in dairy cows.

PubMed

Gozho, G N; Hobin, M R; Mutsvangwa, T

2008-01-01

The objective of this study was to determine the effects of methods of barley grain processing and source of supplemental fat on urea-N transfer to the gastrointestinal tract (GIT) and the utilization of this recycled urea-N in lactating dairy cows. Four ruminally cannulated Holstein cows (656.3 +/- 27.7 kg of BW; 79.8 +/- 12.3 d in milk) were used in a 4 x 4 Latin square design with 28-d periods and a 2 x 2 factorial arrangement of dietary treatments. Experimental diets contained dry-rolled barley or pelleted barley in combination with whole canola or whole flaxseed as supplemental fat sources. Nitrogen balance was measured from d 15 to 19, with concurrent measurements of urea-N kinetics using continuous intrajugular infusions of [15N 15N]-urea. Dry matter intake and N intake were higher in cows fed dry-rolled barley compared with those fed pelleted barley. Nitrogen retention was not affected by diet, but fecal N excretion was higher in cows fed dry-rolled barley than in those fed pelleted barley. Actual and energy-corrected milk yield were not affected by diet. Milk fat content and milk fat yield were higher in cows fed dry-rolled barley compared with those fed pelleted barley. Source of supplemental fat did not affect urea-N kinetics. Urea-N production was higher (442.2 vs. 334.3 g of N/d), and urea-N entering the GIT tended to be higher (272.9 vs. 202.0 g of N/d), in cows fed dry-rolled barley compared with those fed pelleted barley. The amount of urea-N entry into the GIT that was returned to the ornithine cycle was higher (204.1 vs. 159.5 g of N/d) in cows fed dry-rolled barley than in pelleted barley-fed cows. The amount of urea-N recycled to the GIT and used for anabolic purposes, and the amounts lost in the urine or feces were not affected by dietary treatment. Microbial nonammonia N supply, estimated using total urinary excretion of purine derivatives, was not affected by diet. These results show that even though barley grain processing altered urea-N entry into the GIT, the utilization of this recycled urea-N for microbial production was unaffected as the additional urea-N, which entered the GIT was returned to ureagenesis.

Carbon Dioxide Removal via Passive Thermal Approaches

NASA Technical Reports Server (NTRS)

Lawson, Michael; Hanford, Anthony; Conger, Bruce; Anderson, Molly

2011-01-01

A paper describes a regenerable approach to separate carbon dioxide from other cabin gases by means of cooling until the carbon dioxide forms carbon dioxide ice on the walls of the physical device. Currently, NASA space vehicles remove carbon dioxide by reaction with lithium hydroxide (LiOH) or by adsorption to an amine, a zeolite, or other sorbent. Use of lithium hydroxide, though reliable and well-understood, requires significant mass for all but the shortest missions in the form of lithium hydroxide pellets, because the reaction of carbon dioxide with lithium hydroxide is essentially irreversible. This approach is regenerable, uses less power than other historical approaches, and it is almost entirely passive, so it is more economical to operate and potentially maintenance- free for long-duration missions. In carbon dioxide removal mode, this approach passes a bone-dry stream of crew cabin atmospheric gas through a metal channel in thermal contact with a radiator. The radiator is pointed to reject thermal loads only to space. Within the channel, the working stream is cooled to the sublimation temperature of carbon dioxide at the prevailing cabin pressure, leading to formation of carbon dioxide ice on the channel walls. After a prescribed time or accumulation of carbon dioxide ice, for regeneration of the device, the channel is closed off from the crew cabin and the carbon dioxide ice is sublimed and either vented to the environment or accumulated for recovery of oxygen in a fully regenerative life support system.

Growth performance of calves fed microbially enhanced soy protein in pelleted starters.

PubMed

Senevirathne, N D; Anderson, J L; Gibbons, W R; Clapper, J A

2017-01-01

Our objective was to determine effects of feeding calves pelleted starters with microbially enhanced (fungi-treated) soy protein (MSP) in replacement of soybean meal (SBM) with different milk replacers (MR). Thirty-six Holstein calves (2 d old; 24 females, 12 males) in individual hutches were used in a 12-wk randomized complete block design study. Treatments were (1) MSP pellets with MR formulated for accelerated growth (28% crude protein, 18% fat; MSPA), (2) SBM pellets with MR formulated for accelerated growth (SBMA), and (3) MSP pellets with conventional MR (20% crude protein, 20% fat; MSPC). Pellets were similar except for 23% MSP or 23% SBM (dry matter basis). Pellets and water were fed ad libitum throughout the study. Feeding rates of MR on a dry matter basis were 0.37kg twice daily during wk 1, 0.45kg twice daily during wk 2 to 5, and 0.45kg once daily during wk 6. Intakes were recorded daily. Body weights, frame size measurements, and jugular blood samples were collected 2 d every 2 wk at 3 h after the morning feeding. Fecal grab samples were collected 5 times per d for 3 d during wk 12 and then composited by calf for analysis of apparent total-tract digestibility of nutrients using acid detergent insoluble ash as an internal marker. Total and starter pellet dry matter intake were greatest for calves fed SBMA and least for MSPC. Calves had similar average daily gain among treatments, but there was a treatment by week interaction and during the last few weeks of the study calves on MSPC had less body weight compared with MSPA or SBMA. Gain-to-feed ratio was similar among treatments; however, there was a treatment by week interaction. Serum glucose was similar among treatments. Plasma urea nitrogen was greatest for calves fed MSPA and least for MSPC. Plasma concentrations of IGF-1 were greatest for calves fed SBMA. Plasma concentrations of triglycerides were greatest for calves fed MSPC. Plasma concentrations of β-hydroxybutyrate had a treatment by time interaction. Treatments had similar total-tract dry matter digestibility, but calves fed MSPC had greater crude protein digestibility than SBMA, with MSPA similar to both. Results demonstrated calves fed pelleted starters with MSP had maintained growth performance with less starter intake compared with SBM. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Mixed precipitation occurrences over southern Québec, Canada, under warmer climate conditions using a regional climate model

NASA Astrophysics Data System (ADS)

Matte, Dominic; Thériault, Julie M.; Laprise, René

2018-05-01

Winter weather events with temperatures near 0°C are often associated with freezing rain. They can have major impacts on the society by causing power outages and disruptions to the transportation networks. Despite the catastrophic consequences of freezing rain, very few studies have investigated how their occurrences could evolve under climate change. This study aims to investigate the change of freezing rain and ice pellets over southern Québec using regional climate modeling at high resolution. The fifth-generation Canadian Regional Climate Model with climate scenario RCP 8.5 at 0.11° grid mesh was used. The precipitation types such as freezing rain, ice pellets or their combination are diagnosed using five methods (Cantin and Bachand, Bourgouin, Ramer, Czys and, Baldwin). The occurrences of the diagnosed precipitation types for the recent past (1980-2009) are found to be comparable to observations. The projections for the future scenario (2070-2099) suggested a general decrease in the occurrences of mixed precipitation over southern Québec from October to April. This is mainly due to a decrease in long-duration events (≥6 h ). Overall, this study contributes to better understand how the distribution of freezing rain and ice pellets might change in the future using high-resolution regional climate model.

Extruder system for high-throughput/steady-state hydrogen ice supply and application for pellet fueling of reactor-scale fusion experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Combs, S.K.; Foust, C.R.; Qualls, A.L.

Pellet injection systems for the next-generation fusion devices, such as the proposed International Thermonuclear Experimental Reactor (ITER), will require feed systems capable of providing a continuous supply of hydrogen ice at high throughputs. A straightforward concept in which multiple extruder units operate in tandem has been under development at the Oak Ridge National Laboratory. A prototype with three large-volume extruder units has been fabricated and tested in the laboratory. In experiments, it was found that each extruder could provide volumetric ice flow rates of up to {approximately}1.3 cm{sup 3}/s (for {approximately}10 s), which is sufficient for fueling fusion reactors atmore » the gigawatt power level. With the three extruders of the prototype operating in sequence, a steady rate of {approximately}0.33 cm{sup 3}/s was maintained for a duration of 1 h. Even steady-state rates approaching the full ITER design value ({approximately}1 cm{sup 3}/s) may be feasible with the prototype. However, additional extruder units (1{endash}3) would facilitate operations at the higher throughputs and reduce the duty cycle of each unit. The prototype can easily accommodate steady-state pellet fueling of present large tokamaks or other near-term plasma experiments.« less

The amount of food ingested in a single meal by rainbow trout offered chopped herring, dry and wet diets

PubMed

Ruohonen; Grove; McIlroy

1997-07-01

Two-year-old 1·5-kg rainbow trout were held in cages and conditioned by feeding either on low-fat chopped herring (H trout) or dry pellets (P trout) for 15 weeks. Their satiation amounts were then determined under standard conditions. On a wet weight basis H trout ate 2·5-3·5 times more food than P trout; this was sufficient to compensate for the high water content of herring and thereby maintain the dry matter intake. When P trout were offered herring (PH trout) they consumed more food than when offered dry pellets but not as much as H trout. Stomach capacity restricted the intake and their dry matter intake was reduced by c. 40%. When H trout were offered dry pellets (HP trout) they adjusted their intake immediately close to the level of P trout although their larger stomachs could have accommodated more than twice this volume of dry food. The return of appetite after a satiation meal was almost linear with time. Appetite increased at c. 556 mg g-1 body weight h-1 for H trout and at 142 mg g-1 bw h-1 for P trout. The return of appetite in PH trout was significantly slower (c. 370 mg g-1 bw h-1) than in H trout; the previous dietary history of the PH trout limited their capacity to process larger volumes of wet food in a single meal. Fish offered dry diet (P and HP trout) had similar rates of appetite return despite their previous feeding history suggesting that the property of the dry feed itself might limit meal size. The total gastric emptying time of diets of similar dry matter content (with and without large amounts of water) was similar, but the delay time before gastric emptying starts tended to be longer for dry diets. Dry pellets appear to impose a demand for water that prolongs the gastric delay. This water demand is met partly by drinking since the trout fed on dry pellets drank significantly more (436±189 mg kg-1 h-1) than unfed and herring-fed trout which drank little or not at all (65±113 and 70±66 mg kg-1 h-1 respectively). Dietary water facilitated food processing and increased daily dry matter intake of trout when fed four times a day. When only one satiation meal per day was allowed, dietary water had no effect. It is concluded from this work that, in addition to gastric volume, a short-term limitation on the size of satiation meals in the rainbow trout is the availability of water to moisturize the food and thus to promote gastric digestion and emptying. 1997 The Fisheries Society of the British Isles

Effects of Doping and/or Atmosphere on the Electrical Conductivity of Li4Ti5O12

DTIC Science & Technology

2008-11-01

materials were ground with an alumina mortar and pestle with enough methanol to form a slurry. The dried and mixed reactant mixture was pelletized...N. V.; Chaban, N. G.; Petrov, K. I. Inorg. Mater. 1982, 18, 1066. 21. Hayashi, S.; Hatano, H. J. Ceram. Soc. Japan 1994,102, 378. 11 22...with an alumina mortar and pestle with enough methanol to form a slurry. The dried and mixed reactant mixture was pelletized and then heated at 800

Growth of Streptomyces Hygroscopicus in Rotating-Wall Bioreactor Under Simulated Microgravity Inhibits Rapamycin Production

NASA Technical Reports Server (NTRS)

Fang, A.; Pierson, D. L.; Mishra, S. K.; Demain, A. L.

2000-01-01

Growth of Streptomyces hygroscopicus under conditions of simulated microgravity in a rotating-wall bioreactor resulted in a pellet form of growth, lowered dry cell weight, and inhibition of rapamycin production. With the addition of Teflon beads to the bioreactor, growth became much less pelleted, dry cell weight increased but rapamycin production was still markedly inhibited. Growth under simulated microgravity favored extracellular production of rapamycin in contrast to a greater percentage of cell-bound rapamycin observed under normal gravity conditions.

Growth of Steptomyces hygroscopicus in rotating-wall bioreactor under simulated microgravity inhibits rapamycin production

NASA Technical Reports Server (NTRS)

Fang, A.; Pierson, D. L.; Mishra, S. K.; Demain, A. L.

2000-01-01

Growth of Streptomyces hygroscopicus under conditions of simulated microgravity in a rotating-wall bioreactor resulted in a pellet form of growth, lowered dry cell weight, and inhibition of rapamycin production. With the addition of Teflon beads to the bioreactor, growth became much less pelleted, dry cell weight increased but rapamycin production was still markedly inhibited. Growth under simulated microgravity favored extracellular production of rapamycin, in contrast to a greater percentage of cell-bound rapamycin observed under normal gravity conditions.

Techno-economic analysis of using corn stover to supply heat and power to a corn ethanol plant - Part 1: Cost of feedstock supply logistics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sokhansanj, Shahabaddine; Mani, Sudhagar; Togore, Sam

2010-01-01

Supply of corn stover to produce heat and power for a typical 170 dam3 dry mill ethanol plant is proposed. The corn ethanol plant requires 5.6 MW of electricity and 52.3 MW of process heat, which creates the annual stover demand of as much as 140 Gg. The corn stover supply system consists of collection, preprocessing, transportation and on-site fuel storage and preparation to produce heat and power for the ethanol plant. Economics of the entire supply system was conducted using the Integrated Biomass Supply Analysis and Logistics (IBSAL) simulation model. Corn stover was delivered in three formats (square bales,more » dry chops and pellets) to the combined heat and power plant. Delivered cost of biomass ready to be burned was calculated at 73 $ Mg-1 for bales, 86 $ Mg-1 for pellets and 84 $ Mg-1 for field chopped biomass. Among the three formats of stover supply systems, delivered cost of pelleted biomass was the highest due to high pelleting cost. Bulk transport of biomass in the form of chops and pellets can provide a promising future biomass supply logistic system in the US, if the costs of pelleting and transport are minimized.« less

Specific energy consumption and quality of wood pellets produced using high-moisture lodgepole pine grind in a flat die pellet mill

DOE PAGES

Tumuluru, Jaya Shankar

2016-04-16

In the present study a Box–Behnken experimental design was used to understand the effect of the moisture content of lodgepole pine grind (33–39%, w.b.), die speed (40–60 Hz) and preheating temperature (30–90 °C) on the pellet quality and specific energy consumption. The partially dried pellets produced had high-moisture content in the range of 19–28% (w.b.), and were further dried to <9% (w.b.) in a mechanical oven set at 70 °C for 3 h. Dried pellets were further evaluated for pellet moisture content, unit, bulk, tapped density, and durability. Response surface models developed for the product properties have adequately described themore » process based on coefficient of determination values. Surface plots developed indicated higher unit, bulk, and tapped density (1050, 520, 560 kg/m 3) are achievable at 33–35% (w.b.) moisture content of the lodgepole pine grind, die speed of 60 Hz and preheating temperature of 30–60 °C. Higher moisture content of 39% (w.b) reduced unit, bulk, and tapped density to <912, 396, and 452 kg/m 3. Higher durability values of >95% were obtained at 33–35% (w.b.) at lower preheating temperatures of 30–50 °C and higher die speed of >50 Hz. At 33% (w.b.) moisture content of the lodgepole pine grind, preheating temperature of 90 °C, and die speed of 60 Hz, the observed specific energy consumption was <116 kW h/ton. As a result, scanning electron microscope studies indicated that lignin crosslinking is the primary reason for binding of the lodgepole pine grind at high-moisture content.« less

Matrix-analyte-interaction in MALDI-MS: Pellet and nano-electrospray preparations

NASA Astrophysics Data System (ADS)

Horneffer, Verena; Glückmann, Matthias; Krüger, Ralf; Karas, Michael; Strupat, Kerstin; Hillenkamp, Franz

2006-03-01

The incorporation of analytes into matrix crystals and even more so its mechanistic aspects as a prerequisite for a successful MALDI-MS has been discussed controversially in the literature. Solventless sample preparation techniques can shed new light on this question. In order to investigate some crucial aspects of these preparation techniques, lyophylized peptides and proteins were ground or milled with the powder of two different matrices, 2,5-DHB as incorporating matrix and 2,6-DHB for which protein incorporation was definitely excluded in a prior study, and pressed into pellets. The dependence of the quality of the UV-MALDI-spectra on the mass (up to 12,360 Da) and the milling time in a ball mill is reported. For mellitin different initial axial ion velocities were found, when desorbed from 2,5-DHB-pellets as prepared and after wetting and re-drying. Velocities of 150 and 580 m s-1 for dry and wetted pellets are taken as representative for hard desorption from a surface and soft desorption of matrix-incorporated analytes, respectively. Proteins labeled with either fluorescein isothiocyanate (FITC) or Texas Red (TR) were nano-electrosprayed onto a bed of ferulic acid in a [`]dry' or [`]wet' mode. All [`]dry' deposits exhibit strong fluorescence but do not yield MALDI-ion signals. All [`]wet' deposits yield MALDI-signals of the proteins; the fluorescence of FITC is quenched in [`]wet' deposits because of the low matrix pH.

Are dogs (Canis familiaris) misled more by their owners than by strangers in a food choice task?

PubMed

Marshall-Pescini, S; Prato-Previde, E; Valsecchi, P

2011-01-01

Dogs are highly skilled in understanding a large variety of human social cues and use them appropriately to solve a number of different cognitive tasks. They rely on human signals even when these are contradictory or misleading and ultimately prevent them from correctly solving a task. In the following two experiments, we investigated whether the owner and a stranger differently influenced dogs' choices in food discrimination tasks. In Experiment 1, 48 dogs were tested in 3 different conditions: (1) choice between a large and a small amount of dog pellets with no demonstration; (2) choice between a large and a small amount of dog pellets after having witnessed the owner/stranger favouring the small quantity; (3) choice between two single food pellets after observing the owner/stranger choosing one of them. In Experiment 2, 48 dogs could choose between two foods of different palatability: in Condition 1, dogs chose between a slice of sausage and a dry pellet with no demonstration. In Condition 2, the same choice was available but with a person (owner/stranger) showing a preference for the dry pellet. In Condition 3, dogs chose between a single dry pellet and 8 slices of sausage, with the person (owner/stranger) showing a preference for the pellet. In both experiments, dogs conformed to the human's indications even though these led to the selection of the less advantageous option (i.e. the smaller amount of food in Experiment 1 or the low quality food in Experiment 2). However, the owner and the stranger did not differently influence the dogs' behaviour. Results show that dogs are willing to follow a person's indication even when this is visibly (if perhaps only mildly) counterproductive to them and that they are socially prepared to rely equally on cues given by the owner and an unfamiliar friendly person.

Pellet imaging techniques in the ASDEX tokamak

NASA Astrophysics Data System (ADS)

Wurden, G. A.; Büchl, K.; Hofmann, J.; Lang, R.; Loch, R.; Rudyj, A.; Sandmann, W.

1990-11-01

As part of a USDOE/ASDEX collaboration, a detailed examination of pellet ablation in ASDEX with a variety of diagnostics has allowed a better understanding of a number of features of hydrogen ice pellet ablation in a plasma. In particular, fast-gated photos with an intensified Xybion CCD video camera allow in situ velocity measurements of the pellet as it penetrates the plasma. With time resolution of typically 100 ns and exposures every 50 μs, the evolution of each pellet in a multipellet ASDEX tokamak plasma discharge can be followed. When the pellet cloud track has striations, the light intensity profile through the cloud is hollow (dark near the pellet), whereas at the beginning or near the end of the pellet trajectory the track is typically smooth (without striations) and has a gaussian-peaked light emission profile. New, single pellet Stark broadened Dα, Dβ, and Dγ spectra, obtained with a tangentially viewing scanning mirror/spectrometer with Reticon array readout, are consistent with cloud densities of 2×1017 cm-3 or higher in the regions of strongest light emission. A spatially resolved array of Dα detectors shows that the light variations during the pellet ablation are not caused solely by a modulation of the incoming energy flux as the pellet crosses rational q surfaces, but instead are a result of dynamic, nonstationary, ablation process.

Pellet imaging techniques in the ASDEX tokamak (abstract)

NASA Astrophysics Data System (ADS)

Wurden, G. A.; Büchl, K.; Hofmann, J.; Lang, R.; Loch, R.; Rudyj, A.; Sandmann, W.

1990-10-01

As part of a USDOE/ASDEX collaboration, a detailed examination of pellet ablation in ASDEX with a variety of diagnostics has allowed a better understanding of a number of features of hydrogen ice pellet ablation in a plasma. In particular, fast-gated photos with an intensified Xybion CCD video camera allow in situ velocity measurements of the pellet as it penetrates the plasma. With time resolution of typically 100 ns and exposures every 50 μs, the evolution of each pellet in a multipellet ASDEX tokamak plasma discharge can be followed. When the pellet cloud track has striations, the light intensity profile through the cloud is hollow (dark near the pellet), whereas at the beginning or near the end of the pellet trajectory the track is typically smooth (without striations) and has a gaussian-peaked light emission profile. New, single pellet Stark broadened Dα, Dβ, and Dγ spectra, obtained with a tangentially viewing scanning mirror/spectrometer with Reticon array readout, are consistent with cloud densities of 2×1017 cm-3 or higher in the regions of strongest light emission. A spatially resolved array of Dα detectors shows that the light variations during the pellet ablation are not caused solely by a modulation of the incoming energy flux as the pellet crosses rational q surfaces, but instead are a result of dynamic, nonstationary, ablation process.

Effect of cryoprotective diluent and method of freeze-thawing on survival and acrosomal integrity of ram spermatozoa.

PubMed

Pontbriand, D; Howard, J G; Schiewe, M C; Stuart, L D; Wildt, D E

1989-08-01

A multifactorial study analyzed the effects of freezing method, cryoprotective diluent, semen to diluent ratio, and thawing velocity on post-thaw motility, progressive status, and acrosomal integrity of ram spermatozoa. Although semen to diluent ratio (1:3 vs 1:6, v/v) had no effect (P greater than 0.05), overall post-thaw spermatozoal viability was highly dependent on freezing method and cryoprotectant. Improved results were obtained by freezing semen in 0.5-ml French straws compared to dry ice pelleting. Manually freezing straws 5 cm above liquid nitrogen (LN2) was comparable to cooling straws in an automated, programmable LN2 unit. Of the two cryoprotective diluents tested, BF5F (containing the surfactant component sodium and triethanolamine lauryl sulfate) yielded approximately 50% fewer (P less than 0.05) spermatozoa with loose acrosomal caps compared to TEST. Thawing straws in a water bath at a higher velocity (60 degrees C for 8 sec) had no effect (P greater than 0.05) on spermatozoal motility, progressive status ratings, or acrosomal integrity when compared to a lower rate (37 degrees C for 20 sec). For the TEST group, thawing pellets in a dry, glass culture tube promoted (P less than 0.05) percentage sperm motility at 3 and 6 hr post-thawing, but for BF5F diluted semen this approach decreased the % of spermatozoa with normal apical ridges. The results suggest that the poor fertility rates often experienced using thawed ram semen likely result not only from reduced sperm motility, but also from compromised ultrastructural integrity. This damage is expressed by an increased loosening of the acrosomal cap, a factor which appears insensitive to freezing method but markedly influenced by the cryoprotective properties of the diluents tested.

Bench Remarks: Carbon Dioxide.

ERIC Educational Resources Information Center

Bent, Henry A.

1987-01-01

Discusses the properties of carbon dioxide in its solid "dry ice" stage. Suggests several demonstrations and experiments that use dry ice to illustrate Avogadro's Law, Boyle's Law, Kinetic-Molecular Theory, and the effects of dry ice in basic solution, in limewater, and in acetone. (TW)

49 CFR 173.196 - Category A infectious substances.

Code of Federal Regulations, 2011 CFR

2011-10-01

... refrigerated or frozen (ice, pre-frozen packs, dry ice). Ice, dry ice, or other refrigerant must be placed... the secondary packaging must maintain their integrity at the temperature of the refrigerant used, as...

Energy Input and Quality of Pellets Made from Steam-Exploded Douglas Fir (Pseudotsuga menziesii)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sokhansanj, Shahabaddine; Bi, X.T.; Lim, C. Jim

Ground softwood Douglas fir (Pseudotsuga menziesii) was treated with pressurized saturated steam at 200-220 C (1.6-2.4 MPa) for 5-10 min in a sealed container. The contents of the container were released to the atmosphere for a sudden decompression. The steam-exploded wood particles were dried to 10% moisture content and pelletized in a single-piston-cylinder system. The pellets were characterized for their mechanical strength, chemical composition, and moisture sorption. The steamtreated wood required 12-81% more energy to compact into pellets than the untreated wood. Pellets made from steam-treated wood had a breaking strength 1.4-3.3 times the strength of pellets made from untreatedmore » wood. Steam-treated pellets had a reduced equilibrium moisture content of 2-4% and a reduced expansion after pelletization. There was a slight increase in the high heating value from 18.94 to 20.09 MJ/kg for the treated samples. Steam-treated pellets exhibited a higher lengthwise rigidity compared to untreated pellets.« less

Improved compaction of dried tannery wastewater sludge.

PubMed

Della Zassa, M; Zerlottin, M; Refosco, D; Santomaso, A C; Canu, P

2015-12-01

We quantitatively studied the advantages of improving the compaction of a powder waste by several techniques, including its pelletization. The goal is increasing the mass storage capacity in a given storage volume, and reducing the permeability of air and moisture, that may trigger exothermic spontaneous reactions in organic waste, particularly as powders. The study is based on dried sludges from a wastewater treatment, mainly from tanneries, but the indications are valid and useful for any waste in the form of powder, suitable to pelletization. Measurements of bulk density have been carried out at the industrial and laboratory scale, using different packing procedures, amenable to industrial processes. Waste as powder, pellets and their mixtures have been considered. The bulk density of waste as powder increases from 0.64 t/m(3) (simply poured) to 0.74 t/m(3) (tapped) and finally to 0.82 t/m(3) by a suitable, yet simple, packing procedure that we called dispersion filling, with a net gain of 28% in the compaction by simply modifying the collection procedure. Pelletization increases compaction by definition, but the packing of pellets is relatively coarse. Some increase in bulk density of pellets can be achieved by tapping; vibration and dispersion filling are not efficient with pellets. Mixtures of powder and pellets is the optimal packing policy. The best compaction result was achieved by controlled vibration of a 30/70 wt% mixture of powders and pellets, leading to a final bulk density of 1t/m(3), i.e. an improvement of compaction by more than 54% with respect to simply poured powders, but also larger than 35% compared to just pellets. That means increasing the mass storage capacity by a factor of 1.56. Interestingly, vibration can be the most or the least effective procedure to improve compaction of mixtures, depending on characteristics of vibration. The optimal packing (30/70 wt% powders/pellets) proved to effectively mitigate the onset of smouldering, leading to self-heating, according to standard tests, whereas the pure pelletization totally removes the self-heating hazard. Copyright © 2015 Elsevier Ltd. All rights reserved.

Interfacial reactions between DBD and porous catalyst in dry methane reforming

NASA Astrophysics Data System (ADS)

Kameshima, Seigo; Mizukami, Ryo; Yamazaki, Takumi; Prananto, Lukman A.; Nozaki, Tomohiro

2018-03-01

Interaction between dielectric barrier discharge (DBD) and porous catalyst in dry methane reforming (CH4  +  CO2  =  2H2  +  2CO) was studied. Coke formation behavior and coke morphology, as well as material conversion and selectivity, over the cross-section of porous pellets was investigated comprehensively by SEM analysis, Raman spectroscopy and pulsed reforming diagnosis, showing DBD and porous pellet interaction is possible only in the interfacial region (the external surface of the pellet): neither generation of DBD nor the diffusion of plasma generated reactive species in the internal micropores is possible. Coke formation and gasification mechanism in nonthermal plasma catalysis of DMR were discussed based on the catalyst effectiveness factor: low-temperature plasma catalysis is equivalent to the high-temperature thermal catalysis.

Respiratory symptoms and lung function in relation to wood dust and monoterpene exposure in the wood pellet industry.

PubMed

Löfstedt, Håkan; Hagström, Katja; Bryngelsson, Ing-Liss; Holmström, Mats; Rask-Andersen, Anna

2017-06-01

Wood pellets are used as a source of renewable energy for heating purposes. Common exposures are wood dust and monoterpenes, which are known to be hazardous for the airways. The purpose of this study was to study the effect of occupational exposure on respiratory health in wood pellet workers. Thirty-nine men working with wood pellet production at six plants were investigated with a questionnaire, medical examination, allergy screening, spirometry, and nasal peak expiratory flow (nasal PEF). Exposure to wood dust and monoterpenes was measured. The wood pellet workers reported a higher frequency of nasal symptoms, dry cough, and asthma medication compared to controls from the general population. There were no differences in nasal PEF between work and leisure time. A lower lung function than expected (vital capacity [VC], 95%; forced vital capacity in 1 second [FEV 1 ], 96% of predicted) was noted, but no changes were noted during shifts. There was no correlation between lung function and years working in pellet production. Personal measurements of wood dust at work showed high concentrations (0.16-19 mg/m 3 ), and exposure peaks when performing certain work tasks. Levels of monoterpenes were low (0.64-28 mg/m 3 ). There was no association between exposure and acute lung function effects. In this study of wood pellet workers, high levels of wood dust were observed, and that may have influenced the airways negatively as the study group reported upper airway symptoms and dry cough more frequently than expected. The wood pellet workers had both a lower VC and FEV 1 than expected. No cross-shift changes were found.

Respiratory symptoms and lung function in relation to wood dust and monoterpene exposure in the wood pellet industry

PubMed Central

Löfstedt, Håkan; Hagström, Katja; Bryngelsson, Ing-Liss; Holmström, Mats; Rask-Andersen, Anna

2017-01-01

Introduction Wood pellets are used as a source of renewable energy for heating purposes. Common exposures are wood dust and monoterpenes, which are known to be hazardous for the airways. The purpose of this study was to study the effect of occupational exposure on respiratory health in wood pellet workers. Materials and methods Thirty-nine men working with wood pellet production at six plants were investigated with a questionnaire, medical examination, allergy screening, spirometry, and nasal peak expiratory flow (nasal PEF). Exposure to wood dust and monoterpenes was measured. Results The wood pellet workers reported a higher frequency of nasal symptoms, dry cough, and asthma medication compared to controls from the general population. There were no differences in nasal PEF between work and leisure time. A lower lung function than expected (vital capacity [VC], 95%; forced vital capacity in 1 second [FEV1], 96% of predicted) was noted, but no changes were noted during shifts. There was no correlation between lung function and years working in pellet production. Personal measurements of wood dust at work showed high concentrations (0.16–19 mg/m3), and exposure peaks when performing certain work tasks. Levels of monoterpenes were low (0.64–28 mg/m3). There was no association between exposure and acute lung function effects. Conclusions In this study of wood pellet workers, high levels of wood dust were observed, and that may have influenced the airways negatively as the study group reported upper airway symptoms and dry cough more frequently than expected. The wood pellet workers had both a lower VC and FEV1 than expected. No cross-shift changes were found. PMID:28276782

Dry Ice Moves on Mars

NASA Image and Video Library

2013-06-11

Serina Diniega, JPL Systems Engineer, describes the discovery that Martian gullies that end in pits rather than fan deltas are likely caused by block of frozen carbon dioxide (dry ice) sliding down slopes on a cushion of carbon dioxide gas. The pits are formed as the "dry ice" sublimates away.

Long-Term Patterns in Production and Export of Fecal Pellets by Krill and Salps along the Western Antarctic Peninsula

NASA Astrophysics Data System (ADS)

Steinberg, D. K.; Ruck, K. E.; Cope, J. S.

2016-02-01

The Western Antarctic Peninsula (WAP) is one of the most rapidly warming regions on Earth, and where climate-induced changes in zooplankton abundance and species composition could dramatically affect the pelagic food web and biogeochemical cycling. We examined long-term (1993 to the present) and spatial trends in summer abundance of, and fecal pellet production (FPP) by, Antarctic krill (Euphausia superba) and gelatinous salps (Salpa thompsoni) and their relationship with physical and other environmental parameters. Zooplankton were collected as part of the Palmer, Antarctica Long-Term Ecological Research Program (PAL LTER) from the epipelagic zone in a region divided into latitudinal (North, South, and Far South) and cross-shelf (coastal, shelf, slope) sub-regions. Beginning in 2009, FPP and sinking rate experiments were conducted at representative stations along these gradients. FPP peaks occurred every 4-6 years in both species in the north and south, but alternated such that some years were characterized by high krill-mediated export, and others by high salp-mediated export. In the far south (where perennial sea ice still persists), and in both coastal and shelf sub-regions, krill FFP exceeded that of salps. Conversely, off the slope, salp FPP exceeded that of krill. Variability in krill FPP was strongly and positively influenced by primary production 2-years prior, and negatively correlated with sea surface temperature (no lag). Salp FPP was most significantly correlated with sea ice parameters, with highest FPP in years of lowest sea-ice extent, duration, and area. Warmer water and ice-free conditions favored salps over krill, which also increased overall potential export of fecal pellet carbon to depth. We discuss the implications of this potential increase in biological pump efficiency as the climate warms.

Impact of Ice Morphology on Design Space of Pharmaceutical Freeze-Drying.

PubMed

Goshima, Hiroshika; Do, Gabsoo; Nakagawa, Kyuya

2016-06-01

It has been known that the sublimation kinetics of a freeze-drying product is affected by its internal ice crystal microstructures. This article demonstrates the impact of the ice morphologies of a frozen formulation in a vial on the design space for the primary drying of a pharmaceutical freeze-drying process. Cross-sectional images of frozen sucrose-bovine serum albumin aqueous solutions were optically observed and digital pictures were acquired. Binary images were obtained from the optical data to extract the geometrical parameters (i.e., ice crystal size and tortuosity) that relate to the mass-transfer resistance of water vapor during the primary drying step. A mathematical model was used to simulate the primary drying kinetics and provided the design space for the process. The simulation results predicted that the geometrical parameters of frozen solutions significantly affect the design space, with large and less tortuous ice morphologies resulting in wide design spaces and vice versa. The optimal applicable drying conditions are influenced by the ice morphologies. Therefore, owing to the spatial distributions of the geometrical parameters of a product, the boundary curves of the design space are variable and could be tuned by controlling the ice morphologies. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Development of Impregnated Agglomerate Pelletization (IAP) process for fabrication of (Th,U)O 2 mixed oxide pellets

NASA Astrophysics Data System (ADS)

Khot, P. M.; Nehete, Y. G.; Fulzele, A. K.; Baghra, Chetan; Mishra, A. K.; Afzal, Mohd.; Panakkal, J. P.; Kamath, H. S.

2012-01-01

Impregnated Agglomerate Pelletization (IAP) technique has been developed at Advanced Fuel Fabrication Facility (AFFF), BARC, Tarapur, for manufacturing (Th, 233U)O 2 mixed oxide fuel pellets, which are remotely fabricated in hot cell or shielded glove box facilities to reduce man-rem problem associated with 232U daughter radionuclides. This technique is being investigated to fabricate the fuel for Indian Advanced Heavy Water Reactor (AHWR). In the IAP process, ThO 2 is converted to free flowing spheroids by powder extrusion route in an unshielded facility which are then coated with uranyl nitrate solution in a shielded facility. The dried coated agglomerate is finally compacted and then sintered in oxidizing/reducing atmosphere to obtain high density (Th,U)O 2 pellets. In this study, fabrication of (Th,U)O 2 mixed oxide pellets containing 3-5 wt.% UO 2 was carried out by IAP process. The pellets obtained were characterized using optical microscopy, XRD and alpha autoradiography. The results obtained were compared with the results for the pellets fabricated by other routes such as Coated Agglomerate Pelletization (CAP) and Powder Oxide Pelletization (POP) route.

Fermentative hydrogen gas production using biosolids pellets as the inoculum source.

PubMed

Kalogo, Youssouf; Bagley, David M

2008-02-01

Biosolids pellets produced from anaerobically digested municipal wastewater sludge by drying to greater than 90% total solids at 110-115 degrees C for at least 75 min, were tested for their suitability as an inoculum source for fermentative hydrogen production. The hydrogen recoveries (mg gaseous H(2) produced as COD/mg added substrate COD) for glucose-fed batch systems were equal, 20.2-21.5%, between biosolids pellets and boiled anaerobic digester sludge as inoculum sources. Hydrogen recoveries from primary sludge were 2.4% and 3.5% using biosolids pellets and boiled sludge, respectively, and only 0.2% and 0.8% for municipal wastewater. Biosolids pellets should be a practical inoculum source for fermentative hydrogen reactors, although the effectiveness will depend on the wastewater treated.

Effects of different rates of drying cassava root on its toxicity to broiler chicks.

PubMed

Panigrahi, S; Rickard, J; O'Brien, G M; Gay, C

1992-12-01

1. The effects of drying cassava root at different rates on its composition and toxicity to broiler chicks were examined. Unpeeled roots from a high-cyanide cultivar of cassava were chipped and dried at 25 degrees C to a moisture content of below 100 g/kg over 24 h for fast-dried meal (FD) or 72 h for slow-dried meal (SD). The meals were incorporated at 250 and 500 g/kg into semi-synthetic diets which were fed to day-old broiler chicks as mash or pellets in separate experiments. 2. The two drying rates produced meals with similar concentrations of polyphenols, but different concentrations of cyanogens, the latter being 38 and 482 mg total cyanide/kg for SD and FD, respectively. The linamarin, acetonecyanohydrin or total cyanide content measurements of pelleted diets were highly correlated. 3. Growth rates of chicks fed on SD-based diets were significantly higher than those of chicks fed on FD-based diets. Compared with a control diet, weight gain of chicks fed on the 500 g FD/kg diet (containing 258 mg total cyanide/kg) was 77% lower, although performance also appeared to be reduced at 142 mg total cyanide/kg. 4. The ratio of water:food intake of chicks was higher in FD than in SD groups, and this was reflected in the high water content of excreta. There was increased bile excretion, the chloretic effect increasing with the cyanogen content of diet. Pancreas weights were lower in FD than in SD groups in experiment 1 (mash diets), but not in experiment 2 (pelleted diets), while there was a significant interaction between drying method and cassava inclusion rate on liver weight in experiment 2, but not in experiment 1. There were no effects on the mortality rate. 5. Pelleting of diets generated high temperatures, but did not significantly alter the cyanogen concentration or the growth of the chicks. 6. Thus, slower rates of drying cassava roots produce meals with lower cyanogen concentration that are, consequently, less toxic to broiler chicks. Cassava root meal of less than 40 mg total cyanide/kg can be fed to broiler chicks at 500 g/kg without any adverse effects.

Cradle-to-Gate Life Cycle Assessment of Switchgrass Fuel Pellets Manufactured in the Southeastern United States

Treesearch

R. D. Bergman; D. L. Reed; A. M. Taylor; D. P. Harper; D. G. Hodges

2015-01-01

Developing renewable energy sources with low environmental impacts is becoming increasingly important as concerns about consuming fossil fuel sources grow. Cultivating, harvesting, drying, and densifying raw biomass feedstocks into pellets for easy handling and transport is one step forward in this endeavor. However, the corresponding environmental performances must be...

Particulate matter in pack ice of the Beaufort Gyre

USGS Publications Warehouse

Reimnitz, E.; Barnes, P.W.; Weber, W.S.

1993-01-01

Fine sediment occurred in very small patches of turbid ice, as thin spotty surface layers, in mud pellets or in old snowdrifts. The latter were widespread south of 74??N, containing an estimated 22 tonnes of silt and clay km-2. Average particle concentration in sea ice (40 mg1-1) was much higher than in sea water (0.8 mg 1 -1) or in new snow. Assuming one-third of the load is released each year, the estimated deposition rate would equal the measured Holocene rate (~2cm 1000 year-1). Therefore, modern sea-ice rafting represents a substantial fraction of the total Arctic Ocean sediment budget. -from Authors

The Role of Biomass Composition and Steam Treatment on Durability of Pellets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Yong; Chandra, Richard P.; Sokhansanj, Shahab

Steam treatment has been reported to improve the durability of wood pellet likely by changing the physical and chemical structures of wood particles, but published literature is inconclusive about which structure change is the major reason for enhanced durability. Here, in this paper, steam treatment was combined either with alkaline or with SO 2 to study. The solids obtained after steam treatments along with a control sample were dried and each was compacted into pellets. The pellets were then tested for durability. Steam treatment alone dominated improvements in durability. The pellet durability increased with the amount of xylose, but xylosemore » performed better in the pellet from raw poplar than did in the pellet from treated poplar. Water-soluble components contributed a maximum 4% of the durability of poplar pellets. The addition of lignin and sugars to substrates after steam treatment did not improve durability significantly. The surface modification that took place as a result of size reduction during steam treatment was the major reason, contributing about 50% of the durability of the pellet from steam-treated poplar. The acidity of steam treatment slightly affected the relative contributions of these structure changes on the durability. Lastly, the new knowledge helps tailor the chemical and/or mechanical pretreatment involved in pelleting biomass to durable pellets.« less

The Role of Biomass Composition and Steam Treatment on Durability of Pellets

DOE PAGES

Tang, Yong; Chandra, Richard P.; Sokhansanj, Shahab; ...

2018-03-03

Steam treatment has been reported to improve the durability of wood pellet likely by changing the physical and chemical structures of wood particles, but published literature is inconclusive about which structure change is the major reason for enhanced durability. Here, in this paper, steam treatment was combined either with alkaline or with SO 2 to study. The solids obtained after steam treatments along with a control sample were dried and each was compacted into pellets. The pellets were then tested for durability. Steam treatment alone dominated improvements in durability. The pellet durability increased with the amount of xylose, but xylosemore » performed better in the pellet from raw poplar than did in the pellet from treated poplar. Water-soluble components contributed a maximum 4% of the durability of poplar pellets. The addition of lignin and sugars to substrates after steam treatment did not improve durability significantly. The surface modification that took place as a result of size reduction during steam treatment was the major reason, contributing about 50% of the durability of the pellet from steam-treated poplar. The acidity of steam treatment slightly affected the relative contributions of these structure changes on the durability. Lastly, the new knowledge helps tailor the chemical and/or mechanical pretreatment involved in pelleting biomass to durable pellets.« less

Moisture plasticization for enteric Eudragit® L30D-55-coated pellets prior to compression into tablets.

PubMed

Rujivipat, Soravoot; Bodmeier, Roland

2012-05-01

Enteric polymers such as cellulose esters (cellulose acetate phthalate, hydroxypropylmethylcellulose acetate succinate) and methacrylic acid-acrylate copolymers (Eudragit® L100-55 and S100) are quite brittle in the dry state and thus not suitable as pellet coatings for compression into tablets. The objective of this study was to investigate the role of humidity treatment for moisture plasticization in order to successfully compress the enterically coated pellets. The mechanical properties of Eudragit® L100-55 improved dramatically, while the properties of the other enteric polymers showed only minor changes after storage at higher humidity. The significant increase in flexibility of the Eudragit® L film was caused by hydration/plasticization; its elongation value changed from approx. 3% in the dry state to approx. 140% at the higher storage humidity. Storage at 84% relative humidity resulted in comparable release profiles of compressed and uncompressed pellets. The glass transition temperature of Eudragit® L films decreased below the compression temperature (room temperature) at storage humidities between 75% and 84%. The glass transition relative humidity leading to a change from the glassy to the rubbery state was determined by dynamic vapor sorption (DVS) to be 76.8%. Moisture resulted in superior plasticization for Eudragit® L than the conventional plasticizer triethyl citrate. The improved compressibility of high humidity treated Eudragit® L-coated pellets was also shown with single pellet compression data as indicated by an increased crushing force and deformation. In conclusion, moisture plasticization was a highly effective tool to enable the successful compression of pellets coated with the brittle enteric polymer Eudragit® L. Copyright © 2012 Elsevier B.V. All rights reserved.

Processing diets containing corn distillers' dried grains with solubles in growing broiler chickens: effects on performance, pellet quality, ileal amino acids digestibility, and intestinal microbiota.

PubMed

Kim, J S; Hosseindoust, A R; Shim, Y H; Lee, S H; Choi, Y H; Kim, M J; Oh, S M; Ham, H B; Kumar, A; Chae, B J

2018-04-03

The present study investigated the effects of feed form and distillers' dried grains with solubles (DDGS) on growth performance, nutrient digestibility, and intestine microbiota in broilers. A total of 720 broilers (Ross 308; average BW 541 ± 6 g) was randomly allotted to 6 treatments on the basis of BW. There were 6 replicates in each treatment with 20 birds per replicate. Birds were fed 3 different feed forms (mash, simple pellet, and expanded pellet) and DDGS (0 or 20% of diet) in a 3 × 2 factorial arrangement. Simple pellet (SP) and expanded pellet (EP) fed birds showed an increase in BW gain (P < 0.05). The interaction between feed processing and DDGS level was observed on pellet hardness (P < 0.01). The lowest (P < 0.01) pellet durability index (PDI) and hardness were observed in the diet with DDGS. Values for PDI and hardness were higher for EP compared with SP (P < 0.01). Simple pellet decreased ileal digestibility of CP compared to mash feed. The inclusion of DDGS decreased the digestibility of CP, and tended to decrease digestibility of DM (P = 0.056) and gross energy (P = 0.069). Expanded pellet feeding decreased (P < 0.05) the ileal digestibility of isoleucine, lysine, methionine, phenylalanine, threonine, cysteine, and glutamine compared with mash diet. Processed feed increased (P < 0.01) pH in the gizzard and duodenum; however, processing decreased pH in ileum. The addition of DDGS to the diet reduced pH in the duodenum. The population of Lactobacillus spp. was lower in the duodenum of birds fed the EP diet compared to the mash diet. Processed feed increased the colonization of Clostridium spp. in the gizzard. These results indicated that SP and EP in broiler diet had a potential to improve BW gain, but EP compromised amino acid digestibility. In addition, DDGS supplementation (20%) decreased pellet quality and CP digestibility in broiler chickens; however, the growth performance and feed intake were not affected.

The power-consumption-controlled extruder: a tool for pellet production.

PubMed

Kleinebudde, P; Sølvberg, A J; Lindner, H

1994-07-01

Based on the assumption that there is a link between power consumption of an extruder and pellet properties, a control circuit for power consumption was developed. Powder and granulation liquid are fed separately into a twin-screw extruder. The power consumption is controlled by varying the pump rate at a given powder-feed rate; consequently each level of power consumption results in a specific water content of the extrudate for a particular formulation. The shape of pellets depends almost entirely on the level of power consumption irrespective of formulation. The size of dry pellets is additionally affected by a shrinking factor which depends on the water content. The power-consumption-controlled extruder is an appropriate tool for the production of pellets. The system is able to adapt the water content for a formulation automatically.

Enabling Technologies for Medium Additive Manufacturing (MAAM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richardson, Bradley S.; Love, Lonnie J.; Chesser, Phillip C.

ORNL has worked with Cosine Additive, Inc. on the design of MAAM extrusion components. The objective is to improve the print speed and part quality. A pellet extruder has been procured and integrated into the MAAM printer. Print speed has been greatly enhanced. In addition, ORNL and Cosine Additive have worked on alternative designs for a pellet drying and feed system.

Fast plasma shutdown by killer pellet injection in JT-60U with reduced heat flux on the divertor plate and avoiding runaway electron generation

NASA Astrophysics Data System (ADS)

Yoshino, R.; Kondoh, T.; Neyatani, Y.; Itami, K.; Kawano, Y.; Isei, N.

1997-02-01

A killer pellet is an impurity pellet that is injected into a tokamak plasma in order to terminate a discharge without causing serious damage to the tokamak machine. In JT-60U neon ice pellets have been injected into OH and NB heated plasmas and fast plasma shutdowns have been demonstrated without large vertical displacement. The heat pulse on the divertor plate has been greatly reduced by killer pellet injection (KPI), but a low-power heat flux tail with a long time duration is observed. The total energy on the divertor plate increases with longer heat flux tail, so it has been reduced by shortening the tail. Runaway electron (RE) generation has been observed just after KPI and/or in the later phase of the plasma current quench. However, RE generation has been avoided when large magnetic perturbations are excited. These experimental results clearly show that KPI is a credible fast shutdown method avoiding large vertical displacement, reducing heat flux on the divertor plate, and avoiding (or minimizing) RE generation.

Remote fabrication and irradiation test of recycled nuclear fuel prepared by the oxidation and reduction of spent oxide fuel

NASA Astrophysics Data System (ADS)

Jin Ryu, Ho; Chan Song, Kee; Il Park, Geun; Won Lee, Jung; Seung Yang, Myung

2005-02-01

A direct dry recycling process was developed in order to reuse spent pressurized light water reactor (LWR) nuclear fuel in CANDU reactors without the separation of sensitive nuclear materials such as plutonium. The benefits of the dry recycling process are the saving of uranium resources and the reduction of spent fuel accumulation as well as a higher proliferation resistance. In the process of direct dry recycling, fuel pellets separated from spent LWR fuel rods are oxidized from UO2 to U3O8 at 500 °C in an air atmosphere and reduced into UO2 at 700 °C in a hydrogen atmosphere, which is called OREOX (oxidation and reduction of oxide fuel). The pellets are pulverized during the oxidation and reduction processes due to the phase transformation between cubic UO2 and orthorhombic U3O8. Using the oxide powder prepared from the OREOX process, the compaction and sintering processes are performed in a remote manner in a shielded hot cell due to the high radioactivity of the spent fuel. Most of the fission gas and volatile fission products are removed during the OREOX and sintering processes. The mini-elements fabricated by the direct dry recycling process are irradiated in the HANARO research reactor for the performance evaluation of the recycled fuel pellets. Post-irradiation examination of the irradiated fuel showed that microstructural evolution and fission gas release behavior of the dry-recycled fuel were similar to high burnup UO2 fuel.

Effect of diet grinding and pelleting fed either dry or liquid feed on dry matter and pH in the stomach of pigs and the development of gastric ulcers.

PubMed

Mösseler, A; Wintermann, M; Sander, S J; Kamphues, J

2012-12-01

The physical form of diets has a marked impact on the development of gastric ulcers in pigs. Earlier studies showed effects of fine grinding and pelleting on the integrity of gastric mucosa as well as on local intragastric milieu. This study was conducted to evaluate the effects of dry or liquid feeding on intragastric milieu (DM and pH) in pigs. The 23 piglets were housed individually and fed with test diets and water ad lib for 6 wk. Both experimental diets [coarsely ground diet fed as mash (CM) vs. finely ground pelleted diet (FP)] were identical in ingredients (39.5% wheat, 34% barley, 20% soybean meal) and chemical composition and were either offered dry or in liquid (25% DM) form. At the end of the trial the animals were slaughtered; the stomach was removed and samples were taken from different localizations. Feeding diets dry or liquid had no effect on the pH (P > 0.05). The diet noticeably affected the gastric content. The FP diets resulted in a more liquid chyme (P < 0.05), and the intragastric pH did not differ between regions. Feeding CM caused marked effects of localization regarding pH (highest values: pars nonglandularis; lowest values: fundus). None of the pigs fed CM showed signs of gastric ulcers, but the score was markedly higher (P < 0.05) when pigs were fed FP. Therefore the predominant factor for development of gastric ulcers seems to be the structure (particle size) of the diet.

TEMPORARY STORAGE OF BOVINE SEMEN CRYOPRESERVED IN LIQUID NITROGEN ON DRY ICE AND REFREEZING OF FROZEN-THAWED SEMEN.

PubMed

Abdussamad, A M; Gauly, M; Holtz, W

2015-01-01

Two experiments were conducted. The purpose of Experiment 1 was to investigate whether viability of bovine semen stored in liquid nitrogen (-196°C) will be adversely affected by temporary exposure to dry ice (-79°C). It was convincingly shown that post thaw-motility was not affected, regardless whether semen was thawed immediately or after being returned to liquid nitrogen. Shipping or temporary storage on dry ice, thus, is a viable option. In Experiment 2, refreezing of frozen-thawed semen was attempted. The proportion of motile spermatozoa was reduced by a factor of ten to between 6.0 % and 7.4 %, regardless whether thawing occurred directly after removal from liquid nitrogen or after an interim period on dry ice. When semen was refrozen on dry ice before being returned to liquid nitrogen, motility rates were significantly improved (13.0 % to 17.0 %, P<0.05). In both experiments sperm cells that remained motile displayed vigorous forward movement and normal morphological appearance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shahrukh, Hassan; Oyedun, Adetoyese Olajire; Kumar, Amit

Here, a process model was developed to determine the net energy ratio (NER) for production of pellets from steam pretreated agricultural residue (AR) and energy crop (i.e. switchgrass in this case). The NER is a ratio of the net energy output to the total net energy input from non-renewable energy sources into a system. Scenarios were developed to measure the effects of temperature and level of steam pretreatment on the NER of steam pretreated AR- and switch grass-based pellets. The NER for the base case at 6 kg h -1 is 1.76 and 1.37 for steam-pretreated AR- and switchgrass-based pellets,more » respectively. The reason behind the difference is that more energy is required to dry switchgrass pellets than AR pellets. The sensitivity analysis for the model shows that the optimum temperature for steam pretreatment is 160 C with 50% pretreatment (half the feedstock is pretreated, while the rest is undergoes regular pelletization). The uncertainty results for NER for steam pretreated AR and switch grass pellets are 1.62 ± 0.10 and 1.42 ± 0.11, respectively.« less

Effects of feeding pelleted diets without or with distillers dried grains with solubles on fresh belly characteristics, fat quality, and commercial bacon slicing yields of finishing pigs.

PubMed

Overholt, M F; Lowell, J E; Wilson, K B; Matulis, R J; Stein, H H; Dilger, A C; Boler, D D

2016-05-01

One hundred ninety-two pigs were blocked by age and stratified by initial BW (25.7 ± 2.3 kg) into pens (2 barrows and 2 gilts/pen), and within blocks, pens were assigned randomly to 1 of 4 treatments in a 2 × 2 factorial arrangement, with main effects of diet form (meal vs. pelleted) and distillers dried grains with solubles (DDGS) inclusion (0% vs. 30%). Pigs were slaughtered after a 91-d feeding trial, and carcasses were fabricated after a 24-h chilling period. Belly dimensions and flop distance were measured, and an adipose tissue sample from each belly was collected for fatty acid analysis. Bacon was manufactured at a commercial processing facility before being returned to the University of Illinois Meat Science Laboratory for further evaluation. Although bellies from pigs fed pelleted diets were 5.3% heavier ( < 0.01) than bellies from meal-fed pigs, belly weight as a percentage of chilled side weight ( = 0.55) and fresh belly dimensions ( ≥ 0.11) were not affected by diet form. Slab bacon weight and cooked yield were greater ( ≤ 0.01) for bellies from pellet-fed than meal-fed pigs. Despite pellet-fed pigs having a 3.1-unit greater iodine value (IV) than meal-fed pigs, there was no effect ( ≥ 0.16) of diet form on commercial bacon slicing yields. Bacon slabs from pellet-fed pigs produced more ( < 0.01) total bacon slices, but 3.1% fewer ( < 0.01) slices per kilogram than slabs from meal fed pigs. Inclusion of 30% DDGS reduced belly thickness ( < 0.001), flop distance ( < 0.001), and initial belly weight ( = 0.04) by 0.32 cm, 4.97 cm, and 2.85, respectively, and increased ( < 0.001) belly fat IV by 7.1 units compared with bellies from pigs fed 0% DDGS. Feeding 0% DDGS produced more ( < 0.01) total bacon slices than feeding 30% DDGS. Distillers dried grains with solubles inclusion had no effect on slice yields ( ≥ 0.14) or slices per kilogram ( = 0.08). Overall, bellies from pellet-fed pigs were heavier and had greater IV but did not differ in commercial slicing yields from meal-fed pigs. Feeding pigs 30% DDGS produced thinner, softer bellies with greater IV, but slicing yields were not different from bellies of pigs fed 0% DDGS. Thus, swine producers can feed pelleted diets, without or with 30% DDGS, without negatively affecting commercial bacon slicing yield.

Size, shape and flow characterization of ground wood chip and ground wood pellet particles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rezaei, Hamid; Lim, C. Jim; Lau, Anthony

Size, shape and density of biomass particles influence their transportation, fluidization, rates of drying and thermal decomposition. Pelleting wood particles increases the particle density and reduces the variability of physical properties among biomass particles. In this study, pine chips prepared for pulping and commercially produced pine pellets were ground in a hammer mill using grinder screens of 3.2, 6.3, 12.7 and 25.4mmperforations. Pellets consumed about 7 times lower specific grinding energy than chips to produce the same size of particles. Grinding pellets produced the smaller particles with narrower size distribution than grinding chips. Derived shape factors in digital image analysismore » showed that chip particles were rectangular and had the aspect ratios about one third of pellet particles. Pellet particles were more circular shape. The mechanical sieving underestimated the actual particle size and did not represent the size of particles correctly. Instead, digital imaging is preferred. Angle of repose and compressibility tests represented the flow properties of ground particles. Pellet particles made a less compacted bulk, had lower cohesion and did flow easier in a pile of particles. In conclusion, particle shape affected the flow properties more than particle size« less

Comparative net energy ratio analysis of pellet produced from steam pretreated biomass from agricultural residues and energy crops

DOE PAGES

Shahrukh, Hassan; Oyedun, Adetoyese Olajire; Kumar, Amit; ...

2016-04-05

Here, a process model was developed to determine the net energy ratio (NER) for production of pellets from steam pretreated agricultural residue (AR) and energy crop (i.e. switchgrass in this case). The NER is a ratio of the net energy output to the total net energy input from non-renewable energy sources into a system. Scenarios were developed to measure the effects of temperature and level of steam pretreatment on the NER of steam pretreated AR- and switch grass-based pellets. The NER for the base case at 6 kg h -1 is 1.76 and 1.37 for steam-pretreated AR- and switchgrass-based pellets,more » respectively. The reason behind the difference is that more energy is required to dry switchgrass pellets than AR pellets. The sensitivity analysis for the model shows that the optimum temperature for steam pretreatment is 160 C with 50% pretreatment (half the feedstock is pretreated, while the rest is undergoes regular pelletization). The uncertainty results for NER for steam pretreated AR and switch grass pellets are 1.62 ± 0.10 and 1.42 ± 0.11, respectively.« less

Size, shape and flow characterization of ground wood chip and ground wood pellet particles

DOE PAGES

Rezaei, Hamid; Lim, C. Jim; Lau, Anthony; ...

2016-07-11

Size, shape and density of biomass particles influence their transportation, fluidization, rates of drying and thermal decomposition. Pelleting wood particles increases the particle density and reduces the variability of physical properties among biomass particles. In this study, pine chips prepared for pulping and commercially produced pine pellets were ground in a hammer mill using grinder screens of 3.2, 6.3, 12.7 and 25.4mmperforations. Pellets consumed about 7 times lower specific grinding energy than chips to produce the same size of particles. Grinding pellets produced the smaller particles with narrower size distribution than grinding chips. Derived shape factors in digital image analysismore » showed that chip particles were rectangular and had the aspect ratios about one third of pellet particles. Pellet particles were more circular shape. The mechanical sieving underestimated the actual particle size and did not represent the size of particles correctly. Instead, digital imaging is preferred. Angle of repose and compressibility tests represented the flow properties of ground particles. Pellet particles made a less compacted bulk, had lower cohesion and did flow easier in a pile of particles. In conclusion, particle shape affected the flow properties more than particle size« less

Pharmaceutical approaches to preparing pelletized dosage forms using the extrusion-spheronization process.

PubMed

Trivedi, Namrata R; Rajan, Maria Gerald; Johnson, James R; Shukla, Atul J

2007-01-01

Pelletized dosage forms date back to the 1950s, when the first product was introduced to the market. Since then, these dosage forms have gained considerable popularity because of their distinct advantages, such as ease of capsule filling because of better flow properties of the spherical pellets; enhancement of drug dissolution; ease of coating; sustained, controlled, or site-specific delivery of the drug from coated pellets; uniform packing; even distribution in the GI tract; and less GI irritation. Pelletized dosage forms can be prepared by a number of techniques, including drug layering on nonpareil sugar or microcrystalline cellulose beads, spray drying, spray congealing, rotogranulation, hot-melt extrusion, and spheronization of low melting materials or extrusion-spheronization of a wet mass. This review discusses recent developments in the pharmaceutical approaches that have been used to prepare pelletized dosage forms using the extrusion-spheronization process over the last decade. The review is divided into three parts: the first part discusses the extrusion-spheronization process, the second part discusses the effect of varying formulation and process parameters on the properties of the pellets, and the last part discusses the different approaches that have been used to prepare pelletized dosage forms using the extrusion-spheronization process.

The effects of storing and transporting cryopreserved semen samples on dry ice.

PubMed

Til, David; Amaral, Vera L L; Salvador, Rafael A; Senn, Alfred; Paula, Thais S de

2016-12-01

This study aimed to test the effects on sperm viability of transporting cryopreserved semen samples on dry ice. Twenty normozoospermic semen samples were cryopreserved and divided into five groups. The samples in Group 1 were immersed in liquid nitrogen throughout the experiment in cryogenic storage tanks; the cryopreserved straws in Group 2 were placed in a Styrofoam box containing dry ice and kept under these conditions for 48 hours; the samples in Group 3 were kept for 48 hours on dry ice under the same conditions as the Group 2 samples, and were then moved to a storage tank filled with liquid nitrogen; Group 4 samples were also kept for 48 hours in dry ice storage, and the Styrofoam box containing the samples was shipped by plane to assess the effects of shipping; the samples in Group 5 were shipped together with the Group 4 samples and were placed in a storage tank with liquid nitrogen after spending 48 hours stored on dry ice. After thawing, sperm parameters were analyzed for viability, vitality, and motility; spermatozoa were also tested for mitochondrial activity. Significant decreases in motility recovery rates (P=0.01) and vitality (P=0.001) were observed in all groups when compared to the control group. Mitochondrial activity was significantly decreased only in Group 5 (P=0.04), as evidenced by greater numbers of sperm cells not stained by reagent 3,3'-diaminobenzidine. Transportation did not affect the quality of cryopreserved semen samples, but dry ice as a means to preserve the samples during transportation had detrimental effects upon the sperm parameters assessed in this study.

Microbiological quality of cuttlefish (Sepia pharaonis) fillets stored in dry and wet ice.

PubMed

Jeyasekaran, G; Jeya Shakila, R; Sukumar, D

2012-10-01

Microbiological quality of cuttlefish (Sepia pharaonis) fillets stored in three different ice conditions was studied. Fillets stored in wet ice at a ratio of 1:1 (package III) were sensorially acceptable for only 18 h, while that stored in dry ice at 1:1 (package I) and combination of dry ice and wet ice at 1:0.2:0.5 (package II) were in acceptable condition up to 24 h without re-icing and thus there was an extension of shelf life by about 33%. Total bacterial load was 7 log₁₀ cfu/g at the end of the storage period. Total psychrophilic population increased from zero to 7 log₁₀ cfu/g while total lactic acid bacteria from zero to 5 log₁₀ cfu/g. H₂S producers were detected only at 18 h, with a count of 1 log₁₀ cfu/g. Sulphite-reducing Clostridia increased gradually from zero to 110 most probable number count/g. Fresh cuttlefish fillets carried a bacterial flora of Micrococcus, Planococcus, Streptococcus, Moraxella, Proteus and Aeromonas. Pseudomonas was dominant in wet ice pack, while Aeromonas was dominant in both the dry ice and combination pack. Immediately after packing, the temperatures recorded in packages I, II and III were 10.5, 1.2 and 3.0 °C, respectively, which drastically decreased in 1 h and then maintained and finally increased gradually. The results indicate that use of combination of dry ice and wet ice is economical and very much useful to seafood industries, as this package considerably reduced the cost of air freight, as well as improved the quality and shelf life of cuttlefish.

Catalyst for converting synthesis gas to light olefins

DOEpatents

Rao, V. Udaya S.; Gormley, Robert J.

1982-01-01

A catalyst and process for making same useful in the catalytic hydrogenation of carbon monoxide in which a silicalite support substantially free of aluminum is soaked in an aqueous solution of iron and potassium salts wherein the iron and potassium are present in concentrations such that the dried silicalite has iron present in the range of from about 5 to about 25 percent by weight and has potassium present in an amount not less than about 0.2 percent by weight, and thereafter the silicalite is dried and combined with amorphous silica as a binder for pellets, the catalytic pellets are used to convert synthesis gas to C.sub.2 -C.sub.4 olefins.

Growth response of broilers to spray-dried plasma in pelleted or expanded feed processed at high temperature.

PubMed

Campbell, J M; Russell, L E; Crenshaw, J D; Behnke, K C; Clark, P M

2006-09-01

A series of 4 experiments evaluated effects of mash conditioning temperature from a pellet mill or expander on performance of broilers fed pelleted diets containing spray-dried plasma (SDP). All experiments utilized Ross x Ross 308 male broilers randomly assigned to their respective treatments (6 or 10 broilers/pen and 8 or 10 pens/treatment). Treatments in Exp. 1 consisted of a control (0% SDP), SDP coated postpelleting, or SDP blended into the meal prepelleting. Experiment 2 and 3 included the same 3 treatments as in Exp. 1 but with additional treatments of SDP blended into the meal and conditioned at 90 or 95 degrees C before pelleting. In Exp. 4, treatments consisted of a control (0% SDP) or SDP blended into the meal and pelleted (85 degrees C conditioning temperature) or expanded (149 degrees C final effective temperature) and then pelleted. Corn-soybean meal-based diets were formulated to be equal in lysine and ME in all experiments. Pelleted diets were conditioned for 15 s at 85 degrees C, and expanded diets were conditioned at 95 degrees C, 29.7 MJ/t, 13.95 kg/cm2 cone pressure, exit temperature of 149 degrees C, and then pelleted through a 4 x 32-mm die. In Exp. 1, ADG and feed intake were improved (P < 0.05) for broilers fed SDP from d 1 to 28 of age, with greater BW at d 42. In Exp. 2, both in early (d 1 to 28 of age) phases, and overall (d 1 to 42 of age), broilers fed SDP had improved (P < 0.05) gain and efficiency. In Exp. 3, ADG, feed intake, efficiency of gain, and BW were improved (P < 0.01) for broilers fed SDP from d 1 to 21 of age, regardless of conditioning temperature. In Exp. 4, broilers fed SDP had improved (P < 0.05) gain, BW, and feed intake regardless of processing method. Overall, the results of all of the experiments demonstrated that pellet conditioning temperature from 85 to 95 degrees C and expander temperatures to 149 degrees C did not impair the positive growth effects of SDP in pelleted or expanded broiler feed.

The effects of storing and transporting cryopreserved semen samples on dry ice

PubMed Central

Til, David; Amaral, Vera L L; Salvador, Rafael A; Senn, Alfred; de Paula, Thais S

2016-01-01

Objective This study aimed to test the effects on sperm viability of transporting cryopreserved semen samples on dry ice. Methods Twenty normozoospermic semen samples were cryopreserved and divided into five groups. The samples in Group 1 were immersed in liquid nitrogen throughout the experiment in cryogenic storage tanks; the cryopreserved straws in Group 2 were placed in a Styrofoam box containing dry ice and kept under these conditions for 48 hours; the samples in Group 3 were kept for 48 hours on dry ice under the same conditions as the Group 2 samples, and were then moved to a storage tank filled with liquid nitrogen; Group 4 samples were also kept for 48 hours in dry ice storage, and the Styrofoam box containing the samples was shipped by plane to assess the effects of shipping; the samples in Group 5 were shipped together with the Group 4 samples and were placed in a storage tank with liquid nitrogen after spending 48 hours stored on dry ice. After thawing, sperm parameters were analyzed for viability, vitality, and motility; spermatozoa were also tested for mitochondrial activity. Results Significant decreases in motility recovery rates (P=0.01) and vitality (P=0.001) were observed in all groups when compared to the control group. Mitochondrial activity was significantly decreased only in Group 5 (P=0.04), as evidenced by greater numbers of sperm cells not stained by reagent 3,3'-diaminobenzidine. Conclusions Transportation did not affect the quality of cryopreserved semen samples, but dry ice as a means to preserve the samples during transportation had detrimental effects upon the sperm parameters assessed in this study. PMID:28050956

Use of pelleted sericea lespedeza (Lespedeza cuneata) for natural control of coccidia and gastrointestinal nematodes in weaned goats.

PubMed

Kommuru, D S; Barker, T; Desai, S; Burke, J M; Ramsay, A; Mueller-Harvey, I; Miller, J E; Mosjidis, J A; Kamisetti, N; Terrill, T H

2014-08-29

Infection with Eimeria spp. (coccidia) can be devastating in goats, particularly for young, recently-weaned kids, resulting in diarrhea, dehydration, and even death. Feeding dried sericea lespedeza [SL; Lespedeza cuneata (Dum.-Cours.) G. Don.] to young goats has been reported to reduce the effects of internal parasites, including gastrointestinal nematodes (GIN) but there have been no reports of the effects of feeding this forage on Eimeria spp. in goats. Two confinement feeding experiments were completed on recently-weaned intact bucks (24 Kiko-cross, Exp. 1; 20 Spanish, Exp. 2) to determine effects of SL pellets on an established infection of GIN and coccidia. The bucks were assigned to 1 of 2 (Exp. 1) or 3 (Exp. 2) treatment groups based upon the number of Eimeria spp. oocysts per gram (OPG) of feces. In Exp. 1, the kids were fed 1 of 2 pelleted rations ad libitum; 90% SL leaf meal+10% of a liquid molasses/lignin binder mix and a commercial pellet with 12% crude protein (CP) and 24% acid detergent fiber (n=12/treatment group, 2 animals/pen). For Exp. 2, treatment groups were fed (1) 90% SL leaf meal pellets from leaves stored 3 years (n=7), (2) 90% SL pellets from leaf meal stored less than 6 months, (n=7), and the commercial pellets (n=6) ad libitum. For both trials, fecal and blood samples were taken from individual animals every 7 days for 28 days to determine OPG and GIN eggs per gram (EPG) and packed cell volume (PCV), respectively. In Exp. 2, feces were scored for consistency (1=solid pellets, 5=slurry) as an indicator of coccidiosis. In Exp. 1, EPG (P<0.001) and OPG (P<0.01) were reduced by 78.7% and 96.9%, respectively, 7 days after initiation of feeding in goats on the SL pellet diet compared with animals fed the control pellets. The OPG and EPG remained lower in treatment than control animals until the end of the trial. In Exp. 2, goats fed new and old SL leaf meal pellets had 66.2% and 79.2% lower (P<0.05) EPG and 92.2% and 91.2% lower (P<0.05) OPG, respectively, than control animals within 7 days, and these differences were maintained or increased throughout the trial. After 4 weeks of pellet feeding in Exp. 2, fecal scores were lower (P<0.01) in both SL-fed groups compared with control animals, indicating fewer signs of coccidiosis. There was no effect of diet on PCV values throughout either experiment. Dried, pelleted SL has excellent potential as a natural anti-coccidial feed for weaned goats. Copyright © 2014 Elsevier B.V. All rights reserved.

The ice nucleation temperature determines the primary drying rate of lyophilization for samples frozen on a temperature-controlled shelf.

PubMed

Searles, J A; Carpenter, J F; Randolph, T W

2001-07-01

The objective of this study was to determine the influence of ice nucleation temperature on the primary drying rate during lyophilization for samples in vials that were frozen on a lyophilizer shelf. Aqueous solutions of 10% (w/v) hydroxyethyl starch were frozen in vials with externally mounted thermocouples and then partially lyophilized to determine the primary drying rate. Low- and high-particulate-containing samples, ice-nucleating additives silver iodide and Pseudomonas syringae, and other methods were used to obtain a wide range of nucleation temperatures. In cases where the supercooling exceeded 5 degrees C, freezing took place in the following three steps: (1) primary nucleation, (2) secondary nucleation encompassing the entire liquid volume, and (3) final solidification. The primary drying rate was dependent on the ice nucleation temperature, which is stochastic in nature but is affected by particulate content and the presence of ice nucleators. Sample cooling rates of 0.05 to 1 degrees C/min had no effect on nucleation temperatures and drying rate. We found that the ice nucleation temperature is the primary determinant of the primary drying rate. However, the nucleation temperature is not under direct control, and its stochastic nature and sensitivity to difficult-to-control parameters result in drying rate heterogeneity. Nucleation temperature heterogeneity may also result in variation in other morphology-related parameters such as surface area and secondary drying rate. Overall, these results document that factors such as particulate content and vial condition, which influence ice nucleation temperature, must be carefully controlled to avoid, for example, lot-to-lot variability during cGMP production. In addition, if these factors are not controlled and/or are inadvertently changed during process development and scaleup, a lyophilization cycle that was successful on the research scale may fail during large-scale production.

A Bridge Too Far: Suppressing Frost Using an Out-of-Plane Dry Zone

NASA Astrophysics Data System (ADS)

Spohn, Corey; Ahmadi, Farzad; Nath, Saurabh; Boreyko, Jonathan

2017-11-01

It has recently been shown that ice can suppress the formation of any nearby condensation or frost on a substrate. However, these in-plane dry zones require the hygroscopic ice features to be placed on the same surface they are helping to keep dry, which makes it impossible to achieve complete anti-frosting. Here, we create an out-of-plane dry zone by holding two aluminum surfaces parallel to each other, where a uniform sheet of frost was grown on one surface to keep the other surface completely dry. The critical separation required to keep the test surface dry was found to be a function of the ambient supersaturation. We also show that inter-droplet ice bridging, now known to be a primary mechanism for in-plane frost growth, can be similarly extended to an out-of-plane configuration. We freeze a droplet on a hydrophobic surface and suspend a water droplet above it, such that an ice bridge grows toward the water droplet. More generally, these findings show that the recently discovered phenomena of dry zones and ice bridging can be extended to out-of-plane scenarios, which could lead to a better understanding of the behavior of mixed-phase systems. This work was supported by the National Science Foundation (CBET-1604272) and by the 3M Company (Non-Tenured Faculty Award).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tumuluru, Jaya Shankar

In the present study a Box–Behnken experimental design was used to understand the effect of the moisture content of lodgepole pine grind (33–39%, w.b.), die speed (40–60 Hz) and preheating temperature (30–90 °C) on the pellet quality and specific energy consumption. The partially dried pellets produced had high-moisture content in the range of 19–28% (w.b.), and were further dried to <9% (w.b.) in a mechanical oven set at 70 °C for 3 h. Dried pellets were further evaluated for pellet moisture content, unit, bulk, tapped density, and durability. Response surface models developed for the product properties have adequately described themore » process based on coefficient of determination values. Surface plots developed indicated higher unit, bulk, and tapped density (1050, 520, 560 kg/m 3) are achievable at 33–35% (w.b.) moisture content of the lodgepole pine grind, die speed of 60 Hz and preheating temperature of 30–60 °C. Higher moisture content of 39% (w.b) reduced unit, bulk, and tapped density to <912, 396, and 452 kg/m 3. Higher durability values of >95% were obtained at 33–35% (w.b.) at lower preheating temperatures of 30–50 °C and higher die speed of >50 Hz. At 33% (w.b.) moisture content of the lodgepole pine grind, preheating temperature of 90 °C, and die speed of 60 Hz, the observed specific energy consumption was <116 kW h/ton. As a result, scanning electron microscope studies indicated that lignin crosslinking is the primary reason for binding of the lodgepole pine grind at high-moisture content.« less

Conceptual design of a fast-ignition laser fusion reactor based on a dry wall chamber

NASA Astrophysics Data System (ADS)

Ogawa, Y.; Goto, T.; Okano, K.; Asaoka, Y.; Hiwatari, R.; Someya, Y.

2008-05-01

The fast ignition is quite attractive for a compact laser fusion reactor, because a sufficiently high pellet gain is available with a small input energy. We designed an inertial fusion reactor based on Fast-ignition Advanced Laser fusion reactor CONcept, called FALCON-D, where a dry wall is employed for a chamber wall. A simple point model shows that the pellet gain G~100 is available with laser energies of 350kJ for implosion, 50kJ for heating. This results in the fusion yield of 40 MJ in one shot. By increasing the repetition rate up to 30 Hz, the fusion power of 1.2 GWth becomes available. Plant system analysis shows the net electric power to be about 0.4 GWe In the fast ignition it is available to employ a low aspect ratio pellet, which is favorable for the stability during the implosion phase. Here the pellet aspect ratio is reduced to be 2 ~ 4, and the optimization of the pulse shape for the implosion laser are carried out by using the 1-D hydrodynamic simulation code ILESTA-1D. A ferritic steel with a tungsten armour is employed for the chamber wall. The feasibility of this dry wall concept is studied from various engineering aspects such as surface melting, physical and chemical sputtering, blistering and exfoliation by helium retention, and thermo-mechanical fatigue, and it is found that blistering and exfoliation due to the helium retention and fatigue failure due to cyclic thermal load are major concerns. The cost analysis shows that the construction cost is moderate but the cost of electricity is slightly expensive.

Prediction of dry ice mass for firefighting robot actuation

NASA Astrophysics Data System (ADS)

Ajala, M. T.; Khan, Md R.; Shafie, A. A.; Salami, MJE; Mohamad Nor, M. I.

2017-11-01

The limitation in the performance of electric actuated firefighting robots in high-temperature fire environment has led to research on the alternative propulsion system for the mobility of firefighting robots in such environment. Capitalizing on the limitations of these electric actuators we suggested a gas-actuated propulsion system in our earlier study. The propulsion system is made up of a pneumatic motor as the actuator (for the robot) and carbon dioxide gas (self-generated from dry ice) as the power source. To satisfy the consumption requirement (9cfm) of the motor for efficient actuation of the robot in the fire environment, the volume of carbon dioxide gas, as well as the corresponding mass of the dry ice that will produce the required volume for powering and actuation of the robot, must be determined. This article, therefore, presents the computational analysis to predict the volumetric requirement and the dry ice mass sufficient to power a carbon dioxide gas propelled autonomous firefighting robot in a high-temperature environment. The governing equation of the sublimation of dry ice to carbon dioxide is established. An operating time of 2105.53s and operating pressure ranges from 137.9kPa to 482.65kPa were achieved following the consumption rate of the motor. Thus, 8.85m3 is computed as the volume requirement of the CAFFR while the corresponding dry ice mass for the CAFFR actuation ranges from 21.67kg to 75.83kg depending on the operating pressure.

Experimental determination of surface heat transfer coefficient in a dry ice-ethanol cooling bath using a numerical approach.

PubMed

Santos, M V; Sansinena, M; Zaritzky, N; Chirife, J

BACKGROUND: Dry ice-ethanol bath (-78 degree C) have been widely used in low temperature biological research to attain rapid cooling of samples below freezing temperature. The prediction of cooling rates of biological samples immersed in dry ice-ethanol bath is of practical interest in cryopreservation. The cooling rate can be obtained using mathematical models representing the heat conduction equation in transient state. Additionally, at the solid cryogenic-fluid interface, the knowledge of the surface heat transfer coefficient (h) is necessary for the convective boundary condition in order to correctly establish the mathematical problem. The study was to apply numerical modeling to obtain the surface heat transfer coefficient of a dry ice-ethanol bath. A numerical finite element solution of heat conduction equation was used to obtain surface heat transfer coefficients from measured temperatures at the center of polytetrafluoroethylene and polymethylmetacrylate cylinders immersed in a dry ice-ethanol cooling bath. The numerical model considered the temperature dependence of thermophysical properties of plastic materials used. A negative linear relationship is observed between cylinder diameter and heat transfer coefficient in the liquid bath, the calculated h values were 308, 135 and 62.5 W/(m 2 K) for PMMA 1.3, PTFE 2.59 and 3.14 cm in diameter, respectively. The calculated heat transfer coefficients were consistent among several replicates; h in dry ice-ethanol showed an inverse relationship with cylinder diameter.

Quantitative evaluation of haze formation of koji and progression of internal haze by drying of koji during koji making.

PubMed

Ito, Kazunari; Gomi, Katsuya; Kariyama, Masahiro; Miyake, Tsuyoshi

2017-07-01

The construction of an experimental system that can mimic koji making in the manufacturing setting of a sake brewery is initially required for the quantitative evaluation of mycelia grown on/in koji pellets (haze formation). Koji making with rice was investigated with a solid-state fermentation (SSF) system using a non-airflow box (NAB), which produced uniform conditions in the culture substrate with high reproducibility and allowed for the control of favorable conditions in the substrate during culture. The SSF system using NAB accurately reproduced koji making in a manufacturing setting. To evaluate haze formation during koji making, surfaces and cross sections of koji pellets obtained from koji making tests were observed using a digital microscope. Image analysis was used to distinguish between haze and non-haze sections of koji pellets, enabling the evaluation of haze formation in a batch by measuring the haze rate of a specific number of koji pellets. This method allowed us to obtain continuous and quantitative data on the time course of haze formation. Moreover, drying koji during the late stage of koji making was revealed to cause further penetration of mycelia into koji pellets (internal haze). The koji making test with the SSF system using NAB and quantitative evaluation of haze formation in a batch by image analysis is a useful method for understanding the relations between haze formation and koji making conditions. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

[A study of the mechanisms of probiotic effect of Bacillus subtilis 8130 strain].

PubMed

Ushakova, N A; Kotenkova, E V; Kozlova, A A; Nifatov, A V

2006-01-01

The wild-type Bacillus subtilis strain 8130 secreted metabolites that stimulated two to three times the growth of the test cultures of lactic acid bacteria. It exhibited endoglucanase activity that depended on the composition of nutrient medium. The addition of the product of two-stage culturing of B. subtilis 8130 to the diet of pigs (0.2% of fodder weight) made it possible to increase the daily weight gain by 19% and decrease the consumption of mixed fodder by 10%. Digestion of protein, fat, and other organic compounds increased by 3-4% and cellulose by 12%. It was shown that B. subtilis 8130 is a probiotic with targeted action stimulating digestion (primarily the digestion of cellulose). The enrichment of a dry-beer pellet with the product of solid-phase fermentation by bacillus (1 x 10(8) cells per gram dry pellet) allowed the pellet to entered into the diet of a calf (6% of the weight of fodder with probiotic), causing additional weight gain by 12% and a 10% economy of fodder consumption.

Vortex-dislodged cells from bone marrow trephine biopsy yield satisfactory results for flow cytometric immunophenotyping.

PubMed

Bommannan, K; Sachdeva, M U S; Gupta, M; Bose, P; Kumar, N; Sharma, P; Naseem, S; Ahluwalia, J; Das, R; Varma, N

2016-10-01

A good bone marrow (BM) sample is essential in evaluating many hematologic disorders. An unsuccessful BM aspiration (BMA) procedure precludes a successful flow cytometric immunophenotyping (FCI) in most hematologic malignancies. Apart from FCI, most ancillary diagnostic techniques in hematology are less informative. We describe the feasibility of FCI in vortex-dislodged cell preparation obtained from unfixed trephine biopsy (TB) specimens. In pancytopenic patients and dry tap cases, routine diagnostic BMA and TB samples were complemented by additional trephine biopsies. These supplementary cores were immediately transferred into sterile tubes filled with phosphate-buffered saline, vortexed, and centrifuged. The cell pellet obtained was used for flow cytometric immunophenotyping. Of 7955 BMAs performed in 42 months, 34 dry tap cases were eligible for the study. Vortexing rendered a cell pellet in 94% of the cases (32 of 34), and FCI rendered a rapid diagnosis in 100% of the cases (32 of 32) where cell pellets were available. We describe an efficient procedure which could be effectively utilized in resource-limited centers and reduce the frequency of repeat BMA procedures. © 2016 John Wiley & Sons Ltd.

Optimal cooling strategies for players in Australian Tennis Open conditions.

PubMed

Lynch, Grant P; Périard, Julien D; Pluim, Babette M; Brotherhood, John R; Jay, Ollie

2018-03-01

We compared the utility of four cooling interventions for reducing heat strain during simulated tennis match-play in an environment representative of the peak conditions possible at the Australian Open (45°C, <10% RH, 475W/m 2 solar radiation). Nine trained males undertook four trials in a climate chamber, each time completing 4 sets of simulated match-play. During ITF-mandated breaks (90-s between odd-numbered games; 120-s between sets), either iced towels (ICE), an electric fan (FAN dry ), a fan with moisture applied to the skin (FAN wet ), or ad libitum 10°C water ingestion only (CON) was administered. Rectal temperature (T re ), mean skin temperature (T sk ), heart rate (HR), thermal sensation (TS), perceived exertion (RPE) and whole body sweating (WBSR) were measured. After set 3, T re was lower in ICE (38.2±0.3°C) compared to FAN dry (38.7±0.5°C; p=0.02) and CON (38.5±0.5°C; p=0.05), while T re in FAN wet (38.2±0.3°C) was lower than FAN dry (p=0.05). End-exercise T re was lower in ICE (38.1±0.3°C) and FAN wet (38.2±0.4°C) than FAN dry (38.9±0.7°C; p<0.04) and CON (38.8±0.5°C; p<0.04).T sk for ICE (35.3±0.8°C) was lower than all conditions, and T sk for FAN wet (36.6±1.1°C) was lower than FAN dry (38.1±1.3°C; p<0.05). TS for ICE and FAN wet were lower than CON and FAN dry (p<0.05). HR was suppressed in ICE and FAN wet relative to CON and FAN dry (p<0.05). WBSR was greater in FAN dry compared to FAN wet (p<0.01) and ICE (p<0.001). Fan use must be used with skin wetting to be effective in hot/dry conditions. This strategy and the currently recommended ICE intervention both reduced T re by ∼0.5-0.6°C and T sk by ∼1.0-1.5°C while mitigating rises in HR and TS. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Simultaneous excitation of the snake-like oscillations and the m/n = 1/1 resistive interchange modes around the iota = 1 rational surface just after hydrogen pellet injections in LHD plasmas

NASA Astrophysics Data System (ADS)

Bando, T.; Ohdachi, S.; Suzuki, Y.; Sakamoto, R.; Narushima, Y.; Takemura, Y.; Watanabe, K. Y.; Sakakibara, S.; Du, X. D.; Motojima, G.; Tanaka, K.; Morisaki, T.; LHD Experiment Group

2018-01-01

Two types of oscillation phenomena are found just after hydrogen ice pellet injections in the Large Helical Device (LHD). Oscillation phenomena appear when the deposition profile of a hydrogen ice pellet is localized around the rotational transform ι = 1 rational surface. At first, damping oscillations (type-I) appear only in the soft X-ray (SX) emission. They are followed by the second type of oscillations (type-II) where the magnetic fluctuations and density fluctuations synchronized to the SX fluctuations are observed. Both oscillations have poloidal/toroidal mode number, m/n = 1/1. Since the type-II oscillations appear when the local pressure is large and/or the local magnetic Reynold's number is small, it is reasonable that type-II oscillations are caused by the resistive interchange modes. Because both types of oscillations appear simultaneously at slightly different locations and with slightly different frequencies, it is certain that type-I oscillations are different from type-II oscillations, which we believe is the MHD instability. It is possible that type-I oscillations are caused by the asymmetric concentration of the impurities. The type-I oscillations are similar to the impurity snake phenomena observed in tokamaks though type-I oscillations survive only several tens of milliseconds in LHD.

Pitting from Sublimation of Underlying Dry-Ice Layer

NASA Image and Video Library

2011-04-21

NASA Mars Reconnaissance Orbiter took these images of an area near Mars south pole where coalescing or elongated pits are interpreted as signs of an underlying deposit of frozen carbon dioxide, or dry ice.

Reduced pressure ice fog technique for controlled ice nucleation during freeze-drying.

PubMed

Patel, Sajal M; Bhugra, Chandan; Pikal, Michael J

2009-01-01

A method to achieve controlled ice nucleation during the freeze-drying process using an ice fog technique was demonstrated in an earlier report. However, the time required for nucleation was about 5 min, even though only one shelf was used, which resulted in Ostwald ripening (annealing) in some of the vials that nucleated earlier than the others. As a result, the ice structure was not optimally uniform in all the vials. The objective of the present study is to introduce a simple variation of the ice fog method whereby a reduced pressure in the chamber is utilized to allow more rapid and uniform freezing which is also potentially easier to scale up. Experiments were conducted on a lab scale freeze dryer with sucrose as model compound at different concentration, product load, and fill volume. Product resistance during primary drying was measured using manometric temperature measurement. Specific surface area of the freeze-dried cake was also determined. No difference was observed either in average product resistance or specific surface area for the different experimental conditions studied, indicating that with use of the reduced pressure ice fog technique, the solutions nucleated at very nearly the same temperature (-10 degrees C). The striking feature of the "Reduced Pressure Ice Fog Technique" is the rapid ice nucleation (less than a minute) under conditions where the earlier procedure required about 5 min; hence, effects of variable Ostwald ripening were not an issue.

[The studies on the Ku Huang granula technology].

PubMed

Qian, Kun; Kuang, Qi; Dong, Wei; Shen, Jun

2008-02-01

To determine the optimum technology of the Ku Huang granula. Making Emodin and Chrysophanol for index, using HPLC, extracturm softening point data and orthogonal design experiment to research the preparatory technology of the Ku Huang granula to screen the optimum technology. The Ku Huang granula was pelletized at 100% dextrin, 170 degrees C- 175 degrees C spray drying and at the conditions of 75% ethylalcohol, 85 degrees C, 4 Hz, 3 hours fluidizing pelletization. The optimum condition is reasonable.

Fertilizer application equipment for bareroot and container nurseries

Treesearch

John W. Bartok

2002-01-01

Fertilizer application equipment can apply chemicals in dry or liquid form or as manure. The appropriate equipment will place the material at the desired rate in the desired location. In bareroot nurseries, fertilizer is usually applied dry in granulated pellets or coated form. Where in plentiful supply, animal manure may be used, both for nutrients and organic matter...

Dried citrus pulp alters feedlot performance of crossbred heifers during the receiving period

USDA-ARS?s Scientific Manuscript database

A study was designed to determine the effect of feeding dried citrus pulp pellets (CP) on feedlot performance of newly-received English x Continental heifers. Heifers (n=180) were sourced in two loads (188.7+/-18.0 kg and 225.2+/-22.2 kg, respectively) from commercial auction barns and placed on tri...

Dried citrus pulp modulates the physiological and acute phase responses of crossbred heifers to an endotoxin challenge

USDA-ARS?s Scientific Manuscript database

This study examined the effect of feeding dried citrus pulp (CP) pellets on the physiological and acute phase responses (APR) of newly-received crossbred heifers to an endotoxin (lipopolysaccharide; LPS) challenge. Heifers (n=24; 218.3±2.4 kg) were obtained from commercial sale barns and transported...

Ice Accretions and Icing Effects for Modern Airfoils

NASA Technical Reports Server (NTRS)

Addy, Harold E., Jr.

2000-01-01

Icing tests were conducted to document ice shapes formed on three different two-dimensional airfoils and to study the effects of the accreted ice on aerodynamic performance. The models tested were representative of airfoil designs in current use for each of the commercial transport, business jet, and general aviation categories of aircraft. The models were subjected to a range of icing conditions in an icing wind tunnel. The conditions were selected primarily from the Federal Aviation Administration's Federal Aviation Regulations 25 Appendix C atmospheric icing conditions. A few large droplet icing conditions were included. To verify the aerodynamic performance measurements, molds were made of selected ice shapes formed in the icing tunnel. Castings of the ice were made from the molds and placed on a model in a dry, low-turbulence wind tunnel where precision aerodynamic performance measurements were made. Documentation of all the ice shapes and the aerodynamic performance measurements made during the icing tunnel tests is included in this report. Results from the dry, low-turbulence wind tunnel tests are also presented.

Mars: Periglacial Morphology and Implications for Future Landing Sites

NASA Technical Reports Server (NTRS)

Heldmann, Jennifer L.; Schurmeier, Lauren; McKay, Christopher; Davila, Alfonso; Stoker, Carol; Marinova, Margarita; Wilhelm, Mary Beth

2015-01-01

At the Mars Phoenix landing site and in much of the Martian northern plains, there is ice-cemented ground beneath a layer of dry permafrost. Unlike most permafrost on Earth, though, this ice is not liquid at any time of year. However, in past epochs at higher obliquity the surface conditions during summer may have resulted in warmer conditions and possible melting. This situation indicates that the ice-cemented ground in the north polar plains is likely to be a candidate for the most recently habitable place on Mars as near-surface ice likely provided adequate water activity approximately 5 Myr ago. The high elevation Dry Valleys of Antarctica provide the best analog on Earth of Martian ground ice. These locations are the only places on Earth where ice-cemented ground is found beneath dry permafrost. The Dry Valleys are a hyper-arid polar desert environment and in locations above 1500 m elevation, such as University Valley, air temperatures do not exceed 0 C. Thus, similarly to Mars, liquid water is largely absent here and instead the hydrologic cycle is dominated by frozen ice and vapor phase processes such as sublimation. These conditions make the high elevation Dry Valleys a key Mars analog location where periglacial processes and geomorphic features can be studied in situ. This talk will focus on studies of University Valley as a Mars analog for periglacial morphology and ice stability. We will review a landing site selection study encompassing this information gleaned from the Antarctic terrestrial analog studies plus Mars spacecraft data analysis to identify candidate landing sites for a future mission to search for life on Mars.

How Gas Carves Channels

NASA Image and Video Library

2017-01-24

NASA Mars Reconnaissance Orbiter spies a layer of dry ice covering Mars south polar layer. In the spring, gas created from heating of the dry ice escapes through ruptures in the overlying seasonal ice, entraining material from the ground below. The gas erodes channels in the surface, generally exploiting weaker material. The ground likely started as polygonal patterned ground (common in water-ice-rich surfaces), and then escaping gas widened the channels. Fans of dark material are bits of the surface carried onto the top of the seasonal ice layer and deposited in a direction determined by local winds. http://photojournal.jpl.nasa.gov/catalog/PIA11706

Formulation and process strategies to minimize coat damage for compaction of coated pellets in a rotary tablet press: A mechanistic view.

PubMed

Xu, Min; Heng, Paul Wan Sia; Liew, Celine Valeria

2016-02-29

Compaction of multiple-unit pellet system (MUPS) tablets has been extensively studied in the past few decades but with marginal success. This study aims to investigate the formulation and process strategies for minimizing pellet coat damage caused by compaction and elucidate the mechanism of damage sustained during the preparation of MUPS tablets in a rotary tablet press. Blends containing ethylcellulose-coated pellets and cushioning agent (spray dried aggregates of micronized lactose and mannitol), were compacted into MUPS tablets in a rotary tablet press. The effects of compaction pressure and dwell time on the physicomechanical properties of resultant MUPS tablets and extent of pellet coat damage were systematically examined. The coated pellets from various locations at the axial and radial peripheral surfaces and core of the MUPS tablets were excavated and assessed for their coat damage individually. Interestingly, for a MUPS tablet formulation which consolidates by plastic deformation, the tablet mechanical strength could be enhanced without exacerbating pellet coat damage by extending the dwell time in the compaction cycle during rotary tableting. However, the increase in compaction pressure led to faster drug release rate. The location of the coated pellets in the MUPS tablet also contributed to the extent of their coat damage, possibly due to uneven force distribution within the compact. To ensure viability of pellet coat integrity, the formation of a continuous percolating network of cushioning agent is critical and the applied compaction pressure should be less than the pellet crushing strength. Copyright © 2015 Elsevier B.V. All rights reserved.

Ice nucleation temperature influences recovery of activity of a model protein after freeze drying.

PubMed

Cochran, Teresa; Nail, Steven L

2009-09-01

The objective of this study was to determine whether a relationship exists between ice nucleation temperature and recovery of activity of a model protein, lactate dehydrogenase, after freeze drying. Aqueous buffer systems containing 50 microg/mL of protein were frozen in vials with externally mounted thermocouples on the shelf of a freeze dryer, then freeze dried. Various methods were used to establish a wide range of ice nucleation temperatures. An inverse relationship was found between the extent of supercooling during freezing and recovery of activity in the reconstituted solution. The data are consistent with a mechanism of inactivation resulting from adsorption of protein at the ice/freeze-concentrate interface during the freezing process.

DRI Technical Program: Emerging Dynamics of the Marginal Ice Zone Ice, Ocean and Atmosphere Interactions in the Arctic Marginal Ice Zone. Year 3 Annual Report

DTIC Science & Technology

2014-09-30

Institution The Scottish Association for Marine Science tmaksym@whoi.edu Phil.Hwang@sams.ac.uk LONG-TERM GOALS This DRI TECHNICAL PROGRAM (Emerging...jpw28@bas.ac.uk tmaksym@whoi.edu Co-PRINCIPAL INVESTIGATOR: Byongjun (Phil) Hwang The Scottish Association for Marine Science Phil.Hwang@sams.ac.uk 2

Application of quality by design (QbD) to formulation and processing of naproxen pellets by extrusion-spheronization.

PubMed

Wang, Junlin; Kan, Shuling; Chen, Tong; Liu, Jianping

2015-03-01

The aim of this research was to apply quality by design (QbD) to the development of naproxen loaded core pellets which can be used as the potential core for colon-specific pellets. In the early stages of this study, prior knowledge and preliminary studies were systematically incorporated into the risk assessment using failure mode and effect analysis (FMEA) and fishbone diagram. Then Plackett-Burman design was used to screen eight potential high risk factors (spheronization speed, spheronization time, extrusion speed, drying method, CCMC-Na concentration, lactose concentration, water concentration and Tween 80 concentration) obtained from the above risk assessment. It was discovered that out of the eight potential high risk factors only three factors (spheronization speed, extrusion speed and CCMC-Na concentration) had significant effects on the quality of the pellets. This allowed the use of Box-Behnken design (BBD) to fully elucidate the relationship between the variables and critical quality attribute (CQA). Finally, the final control space was established within which the quality of the pellets can meet the requirement of colon-specific drug delivery system. This study demonstrated that naproxen loaded core pellets were successfully designed using QbD principle.

Odor, gaseous and PM10 emissions from small scale combustion of wood types indigenous to Central Europe

NASA Astrophysics Data System (ADS)

Kistler, Magdalena; Schmidl, Christoph; Padouvas, Emmanuel; Giebl, Heinrich; Lohninger, Johann; Ellinger, Reinhard; Bauer, Heidi; Puxbaum, Hans

2012-05-01

In this study, we investigated the emissions, including odor, from log wood stoves, burning wood types indigenous to mid-European countries such as Austria, Czech Republic, Hungary, Slovak Republic, Slovenia, Switzerland, as well as Baden-Württemberg and Bavaria (Germany) and South Tyrol (Italy). The investigations were performed with a modern, certified, 8 kW, manually fired log wood stove, and the results were compared to emissions from a modern 9 kW pellet stove. The examined wood types were deciduous species: black locust, black poplar, European hornbeam, European beech, pedunculate oak (also known as “common oak”), sessile oak, turkey oak and conifers: Austrian black pine, European larch, Norway spruce, Scots pine, silver fir, as well as hardwood briquettes. In addition, “garden biomass” such as pine cones, pine needles and dry leaves were burnt in the log wood stove. The pellet stove was fired with softwood pellets. The composite average emission rates for log wood and briquettes were 2030 mg MJ-1 for CO; 89 mg MJ-1 for NOx, 311 mg MJ-1 for CxHy, 67 mg MJ-1 for particulate matter PM10 and average odor concentration was at 2430 OU m-3. CO, CxHy and PM10 emissions from pellets combustion were lower by factors of 10, 13 and 3, while considering NOx - comparable to the log wood emissions. Odor from pellets combustion was not detectable. CxHy and PM10 emissions from garden biomass (needles and leaves) burning were 10 times higher than for log wood, while CO and NOx rise only slightly. Odor levels ranged from not detectable (pellets) to around 19,000 OU m-3 (dry leaves). The odor concentration correlated with CO, CxHy and PM10. For log wood combustion average odor ranged from 536 OU m-3 for hornbeam to 5217 OU m-3 for fir, indicating a considerable influence of the wood type on odor concentration.

Toxicities of TNT and RDX to the Earthworm Eisenia fetida in Five Soils with Contrasting Characteristics

DTIC Science & Technology

2013-05-01

light. Earthworm colonies were fed biweekly with alfalfa food consisting of dehydrated alfalfa pellets (27% fiber, 17% protein, 1.5% fat; Ohio Blenders...of PA; York, PA). Before use, the alfalfa pellets were hydrated, fermented for at least 14 days, air-dried, and ground to a course powder. Earthworm...assays, a 2 g bolus of prepared alfalfa food was added to each jar, moistened with an atomizer, and covered with soil from within the jar. Clear

Deer exposed to exceptionally high concentrations of lead near the continental mine in Idaho, USA

USGS Publications Warehouse

Beyer, W.N.; Gaston, G.; Brazzle, R.; O'Connell, A.F.; Audet, D.J.

2007-01-01

Habitat surrounding the inactive Continental Mine in northern Idaho, USA, supports bear (Ursus arctos, Ursus americanus), moose (Alces alces), elk (Cervus elaphus), woodland caribou (Rangifer tarandus caribou), and abundant mule (Odocoileus hemionus) and white-tailed deer (Odocoileus virginianus). Tailings on the mining site were capped and remediated in 2003 to reduce environmental exposure of surrounding soil and sediments of Blue Joe Creek, downslope of the mine. Before capping, the mean Pb concentration in deer pellets collected on-site was 920 mg/kg of Pb (dry wt). This exposure, if chronic, would be comparable to an exposure that could be lethal to cattle or horses. Surprisingly, the mean pellet Pb concentration of 950 mg/kg in 2004 was as high as it was before remediation, and it was related to a high rate of soil ingestion. Mean soil content of the pellets collected from the capped site in 2004 was 22% dry weight, estimated from the acid-insoluble ash, a marker of soil ingestion. Clumps of sand and bits of rock were observed inside some of the pellets, and Pb concentrations in the pellets were correlated (p < 0.05) with soil content. Although terrestrial risk assessments generally estimate exposure from diets and from incidentally ingested soil, the deer at this site were directly ingesting contaminated soil or mining waste. The mean Pb concentration of this ingested soil was estimated as 6,700 mg/kg and the maximum as 25,000 mg/kg, well above the Pb concentrations measured in the remediated cap. The deer seemed to be ingesting soil or mining waste from one or more small but highly contaminated sources located beyond the remediated cap.

Scaling of Lift Degradation Due to Anti-Icing Fluids Based Upon the Aerodynamic Acceptance Test

NASA Technical Reports Server (NTRS)

Broeren, Andy P.; Riley, James T.

2012-01-01

In recent years, the FAA has worked with Transport Canada, National Research Council Canada (NRC) and APS Aviation, Inc. to develop allowance times for aircraft operations in ice-pellet precipitation. These allowance times are critical to ensure safety and efficient operation of commercial and cargo flights. Wind-tunnel testing with uncontaminated anti-icing fluids and fluids contaminated with simulated ice pellets had been carried out at the NRC Propulsion and Icing Wind Tunnel (PIWT) to better understand the flowoff characteristics and resulting aerodynamic effects. The percent lift loss on the thin, high-performance wing model tested in the PIWT was determined at 8 angle of attack and used as one of the evaluation criteria in determining the allowance times. Because it was unclear as to how performance degradations measured on this model were relevant to an actual airplane configuration, some means of interpreting the wing model lift loss was deemed necessary. This paper describes how the lift loss was related to the loss in maximum lift of a Boeing 737-200ADV airplane through the Aerodynamic Acceptance Test (AAT) performed for fluids qualification. A loss in maximum lift coefficient of 5.24 percent on the B737-200ADV airplane (which was adopted as the threshold in the AAT) corresponds to a lift loss of 7.3 percent on the PIWT model at 8 angle of attack. There is significant scatter in the data used to develop the correlation related to varying effects of the anti-icing fluids that were tested and other factors. A statistical analysis indicated the upper limit of lift loss on the PIWT model was 9.2 percent. Therefore, for cases resulting in PIWT model lift loss from 7.3 to 9.2 percent, extra scrutiny of the visual observations is required in evaluating fluid performance with contamination.

Scaling of Lift Degradation Due to Anti-Icing Fluids Based Upon the Aerodynamic Acceptance Test

NASA Technical Reports Server (NTRS)

Broeren, Andy; Riley, Jim

2012-01-01

In recent years, the FAA has worked with Transport Canada, National Research Council Canada (NRC) and APS Aviation, Inc. to develop allowance times for aircraft operations in ice-pellet precipitation. These allowance times are critical to ensure safety and efficient operation of commercial and cargo flights. Wind-tunnel testing with uncontaminated anti-icing fluids and fluids contaminated with simulated ice pellets had been carried out at the NRC Propulsion and Icing Wind Tunnel (PIWT) to better understand the flow-off characteristics and resulting aerodynamic effects. The percent lift loss on the thin, high-performance wing model tested in the PIWT was determined at 8 deg. angle of attack and used as one of the evaluation criteria in determining the allowance times. Because it was unclear as to how performance degradations measured on this model were relevant to an actual airplane configuration, some means of interpreting the wing model lift loss was deemed necessary. This paper describes how the lift loss was related to the loss in maximum lift of a Boeing 737-200ADV airplane through the Aerodynamic Acceptance Test (AAT) performed for fluids qualification. A loss in maximum lift coefficient of 5.24% on the B737-200ADV airplane (which was adopted as the threshold in the AAT) corresponds to a lift loss of 7.3% on the PIWT model at 8 deg. angle of attack. There is significant scatter in the data used to develop the correlation related to varying effects of the anti-icing fluids that were tested and other factors. A statistical analysis indicated the upper limit of lift loss on the PIWT model was 9.2%. Therefore, for cases resulting in PIWT model lift loss from 7.3% to 9.2%, extra scrutiny of the visual observations is required in evaluating fluid performance with contamination.

Specimen Collection and Submission Manual

DTIC Science & Technology

2016-06-01

immunoassays Specimen: tissue or bone marrow (100 mg); Whole EDTA blood or serum (0.5 ml) Nasopharyngeal or throat swab, dry or in transport medium; Sputum... Syndrome Coronavirus (MERS-CoV) – detection in clinical samples Methodology: molecular Specimen: If possible collect 3 specimen types (lower...guidelines-clinical-specimens.html) Shipping: ship cold on wet ice or ice packs. For delays exceeding 72 hours, ship frozen on dry ice. Turnaround: 1-2

Net energy ratio for the production of steam pretreated biomass-based pellets

DOE PAGES

Shahrukh, Hassan; Oyedun, Adetoyese Olajire; Kumar, Amit; ...

2015-06-21

In this study, a process model was developed to determine the net energy ratio (NER) for both regular and steam-pretreated pellet production from ligno-cellulosic biomass. NER is a ratio of the net energy output to the total net energy input from non-renewable energy source into the system. Scenarios were developed to measure the effect of temperature and level of steam pretreatment on the NER of both production processes. The NER for the base case at 6 kg h –1 is 1.29 and 5.0 for steam-pretreated and regular pellet production respectively. However, at the large scale NER would improve. The majormore » factor for NER is energy for steam and drying unit. The sensitivity analysis for the model shows that the optimum temperature for steam pretreatment is 200 °C with 50% pretreatment (Steam pretreating 50% feed stock, while the rest is undergoing regular pelletization). Uncertainty result for steam pretreated and regular pellet is 1.35 ± 0.09 and 4.52 ± 0.34 respectively.« less

Emission of volatile aldehydes and ketones from wood pellets under controlled conditions.

PubMed

Arshadi, Mehrdad; Geladi, Paul; Gref, Rolf; Fjällström, Pär

2009-11-01

Different qualities of biofuel pellets were made from pine and spruce sawdust according to an industrial experimental design. The fatty/resin acid compositions were determined by gas chromatography-mass spectrometry for both newly produced pellets and those after 2 and 4 weeks of storage. The aldehydes/ketones compositions were determined by high performance liquid chromatography at 0, 2, and 4 weeks. The designs were analyzed for the response variables: total fatty/resin acids and total aldehydes/ketones. The design showed a strong correlation between the pine fraction in the pellets and the fatty/resin acid content but the influence decreased over storage time. The amount of fatty/resin acids decreased approximately 40% during 4 weeks. The influence of drying temperature on the aldehyde/ketone emission of fresh pellets was also shown. The amounts of emitted aldehydes/ketones generally decreased by 45% during storage as a consequence of fatty/resin acid oxidation. The matrices of individual concentrations were subjected to multivariate data analysis. This showed clustering of the different experimental runs and demonstrated the important mechanism of fatty/resin acid conversion.

Emissions characterization of residential wood-fired hydronic heater technologies

NASA Astrophysics Data System (ADS)

Kinsey, John S.; Touati, Abderrahmane; Yelverton, Tiffany L. B.; Aurell, Johanna; Cho, Seung-Hyun; Linak, William P.; Gullett, Brian K.

2012-12-01

Residential wood-fired hydronic heaters (RWHHs) can negatively impact the local ambient air quality and thus are an environmental concern in wood burning areas of the U. S. Only a few studies have been conducted which characterize the emissions from RWHHs. To address the lack of emissions data, a study was conducted on four appliances of differing design using multiple fuel types to determine their thermal, boiler, and combustion efficiency as well as the emissions of carbon dioxide (CO2), carbon monoxide (CO), total hydrocarbons (THC), nitrous oxide (N2O), methane (CH4), total particulate matter (PM) mass, and particle number as well as particle size distribution (PSD). Three of these appliances were fired with split-log cordwood with the fourth unit using hardwood pellets. The measured thermal efficiencies for the appliances tested varied from 22 to 44% and the combustion efficiencies from 81 to 98%. Depending on appliance and fuel type, the emission factors ranged from about 1300 to 1800 g kg-1 dry fuel for CO2, 8-190 g kg-1 dry fuel for CO, <1-54 g kg-1 dry fuel for THC and 6-120 mg kg-1 for N2O. For the particle phase pollutants, the PM mass emission factors ranged from 0.31 to 47 g kg-1 dry fuel and the PM number emission factors from 8.5 × 1010 to 2.4 × 1014 particles kg-1 dry fuel, also depending on the appliance and fuel tested. The PSD for all four appliances indicated a well established accumulation mode with evidence of a nucleation mode present for Appliances A and B. The average median aerodynamic particle diameters observed for the four appliances ranged from 84 to 187 nm while burning red oak or pellets. In general, the pellet-burning appliance had the highest overall operating efficiency and lowest emissions of the four units tested.

Innovative methodology for electrical conductivity measurements and metal partition in biosolid pellets

NASA Astrophysics Data System (ADS)

Jordan, Manuel Miguel; Rincón-Mora, Beatriz; Belén Almendro-Candel, María; Navarro-Pedreño, José; Gómez-Lucas, Ignacio; Bech, Jaume

2017-04-01

Use of biosolids to improve the nutrient content in a soil is a common practice. The obligation to restore abandoned mine and the correct application of biosolids is guaranteed by the legislation on waste management, biosolids and soil conservation (Jordán et al. 2008). The present research was conducted to determine electrical conductivity in dry wastes (pellets) using a innovative methodology (Camilla and Jordán, 2009). On the other hand, the present study was designed to examine the distribution of selected heavy metals in biosolid pellets, and also to relate the distribution patterns of these metals. In this context, heavy metal concentrations were studied in biosolid pellets under different pressures. Electrical conductivity measurements were taken in biosolid pellets under pressures on the order of 50 to 150 MPa and with currents of 10-15 A. Measurements of electrical conductivity and heavy metal content for different areas (H1, H2, and H3) were taken. Total content of metals was determined following microwave digestion and analysed by ICP/MS. Triplicate portions were weighed in polycarbonate centrifuge tubes and sequentially extracted. The distribution of chemical forms of Cd, Ni, Cr, and Pb in the biosolids was studied using a sequential extraction procedure that fractionates the metal into soluble-exchangeable, specifically sorbed-carbonate bound, oxidizable, reducible, and residual forms. The residual, reducible, and carbonate-sorbed forms were dominant. Higher Cr and Ni content were detected in pellets made with biosolids from the H3. The highest Cd and Ni values were detected in the H2. The trends of the conductivity curves were similar for the sludge from the isolation surface (H1) and for the mesophilous area (H2). In the case of the thermophilous area (H3), the electrical conductivity showed extremely high values. This behaviour was similar in the case of the Cr and Ni content. However, in the case of Cd and Pb, the highest values were detected in the H2. This experiment could be useful for establishing a general rule for taking measurements of electrical conductivity and heavy metals in biosolid pellets and other types of dry wastes. References Camilla S, Jordán MM (2009) Electrical conductivity measurements in sewage sludge pellets: innovative techniques for environmental management. J Hazard Mater 168:1260-1263 Jordán, MM, Rincón-Mora, B; Almendro, MB (2015). Heavy metal distribution and electrical conductivity measurements in biosolid pellets. J, Soils and Sediments, 16 1176-118

Wave-Ice and Air-Ice-Ocean Interaction During the Chukchi Sea Ice Edge Advance

DTIC Science & Technology

2014-09-30

During cruise CU-B UAF UW Airborne expendable Ice Buoy (AXIB) Ahead, at and inside ice edge Surface meteorology T, SLP ~1 year CU-B UW...Balance (IMB) buoys Inside ice edge w/ >50cm thickness Ice mass balance T in snow-ice-ocean, T, SLP at surface ~1 year WHOI CRREL (SeaState DRI

Echo Source Discrimination in Airborne Radar Sounding Data for Mars Analog Studies, Dry Valleys, Antarctica

NASA Technical Reports Server (NTRS)

Holt, J. W.; Blankenship, D. D.; Peters, M. E.; Kempf, S. D.; Morse, D. L.; Williams, B. J.

2003-01-01

The recent identification of features on Mars exhibiting morphologies consistent with ice/rock mixtures, near-surface ice bodies and near-surface liquid water [1,2], and the importance of such features to the search for water on Mars, highlights the need for appropriate terrestrial analogs in order to prepare for upcoming radar missions targeting these and other water-related features. Climatic, hydrological, and geological conditions in the McMurdo Dry Valleys of Antarctica are analogous in many ways to those on Mars, and a number of ice-related features in the Dry Valleys may have direct morphologic and compositional counterparts on Mars.

The determination of optimum condition in water hyacinth drying process by mixed adsorption drying method and modified fly ash as an adsorbent

NASA Astrophysics Data System (ADS)

Saputra, Asep Handaya; Putri, Rizky Anggreini

2017-05-01

Water hyacinth is an aquatic weed that has a very fast growth which makes it becomes a problem to the ecosystem. On the other hand, water hyacinth has a high fiber content (up to 20% by weight) which makes it potential to become raw material for composites and textile industries. As an aquatic plant, water hyacinth has a high initial moisture content that reaches more than 90%. Meanwhile the moisture content of fiber as a raw material for composite and textile industry should not be more than 10% to maintain the good quality of the products. Mixed adsorption drying method is one of the innovative method that can replace conventional drying process. Fluidization method which has been commonly used in agricultural and pharmaceutical products drying, can be enhanced by combining it with the adsorption method as performed in this study. In mixed fluidization-adsorption drying method, fly ash as adsorbent and water hyacinth fiber were put together into the fluidization column where the drying air evaporate the moisture content in water hyacinth fiber. In addition, the adsorbent adsorb the moisture content in the drying air to make the moisture content of the drying air remain low. The drying process is performed in various temperature and composition of water hyacinth and adsorbent in order to obtain the optimum drying condition. In addition, the effect of fly ash pellet and fly ash powder to the drying process was also performed. The result shows that the higher temperature and the more amount of adsorbent results in the faster drying rate. Fly ash pellet shows a better adsorption since it has a smaller pore diameter and wider surface area. The optimum temperature obtained from this study is 60°C and the optimum ratio of water hyacinth and fly ash is 50:50.

Ross Sea Till Properties: Implications for Ice Sheet Bed Interaction

NASA Astrophysics Data System (ADS)

Halberstadt, A. R.; Anderson, J. B.; Simkins, L.; Prothro, L. O.; Bart, P. J.

2015-12-01

Since the discovery of a pervasive shearing till layer underlying Ice Stream B, the scientific community has categorized subglacial diamictons as either deformation till or lodgement till primarily based on shear strength. Deformation till is associated with streaming ice, formed through subglacial deformation of unconsolidated sediments. Lodgement till is believed to be deposited by the plastering of sediment entrained at the base of slow-flowing ice onto a rigid bed. Unfortunately, there has been a paucity of quantitative data on the spatial distribution of shear strength across the continental shelf. Cores collected from the Ross Sea on cruises NBP1502 and NBP9902 provide a rich dataset that can be used to interpret till shear strength variability. Till strengths are analyzed within the context of: (1) geologic substrate; (2) water content and other geotechnical properties; (3) ice sheet retreat history; and (4) geomorphic framework. Tills display a continuum of shear strengths rather than a bimodal distribution, suggesting that shear strength cannot be used to distinguish between lodgement and deformation till. Where the substrate below the LGM unconformity is comprised of older lithified deposits, till shear strengths are both highly variable within the till unit, as well as highly variable between cores. Conversely, where ice streams flowed across unconsolidated Plio-Pleistocene deposits, shear strengths are low and less variable within the unit and between cores. This suggests greater homogenization of cannibalized tills, and possibly a deeper pervasive shear layer. Coarser-grained tills are observed on banks and bank slopes, with finer tills in troughs. Highly variable and more poorly sorted tills are found in close proximity to sediment-based subglacial meltwater channels, attesting to a change in ice-bed interaction as subglacial water increases. Pellets (rounded sedimentary clasts of till matrix) are observed in Ross Sea cores, suggesting a history of deformation responsible for pellet formation. Till strength was measured in a variety of environments, including mega-scale lineations and grounding zone wedges; ongoing work focuses on evaluating till shear strengths within a geomorphic context. These analyses are used to re-evaluate till genesis, transport, and characterization.

Heterogeneous ice nucleation of α-pinene SOA particles before and after ice cloud processing

NASA Astrophysics Data System (ADS)

Wagner, Robert; Höhler, Kristina; Huang, Wei; Kiselev, Alexei; Möhler, Ottmar; Mohr, Claudia; Pajunoja, Aki; Saathoff, Harald; Schiebel, Thea; Shen, Xiaoli; Virtanen, Annele

2017-05-01

The ice nucleation ability of α-pinene secondary organic aerosol (SOA) particles was investigated at temperatures between 253 and 205 K in the Aerosol Interaction and Dynamics in the Atmosphere cloud simulation chamber. Pristine SOA particles were nucleated and grown from pure gas precursors and then subjected to repeated expansion cooling cycles to compare their intrinsic ice nucleation ability during the first nucleation event with that observed after ice cloud processing. The unprocessed α-pinene SOA particles were found to be inefficient ice-nucleating particles at cirrus temperatures, with nucleation onsets (for an activated fraction of 0.1%) as high as for the homogeneous freezing of aqueous solution droplets. Ice cloud processing at temperatures below 235 K only marginally improved the particles' ice nucleation ability and did not significantly alter their morphology. In contrast, the particles' morphology and ice nucleation ability was substantially modified upon ice cloud processing in a simulated convective cloud system, where the α-pinene SOA particles were first activated to supercooled cloud droplets and then froze homogeneously at about 235 K. As evidenced by electron microscopy, the α-pinene SOA particles adopted a highly porous morphology during such a freeze-drying cycle. When probing the freeze-dried particles in succeeding expansion cooling runs in the mixed-phase cloud regime up to 253 K, the increase in relative humidity led to a collapse of the porous structure. Heterogeneous ice formation was observed after the droplet activation of the collapsed, freeze-dried SOA particles, presumably caused by ice remnants in the highly viscous material or the larger surface area of the particles.

Insights into the effects of patchy ice layers on water balance heterogeneity in peatlands

NASA Astrophysics Data System (ADS)

Dixon, Simon; Kettridge, Nicholas; Devito, Kevin; Petrone, Rich; Mendoza, Carl; Waddington, Mike

2017-04-01

Peatlands in boreal and sub-arctic settings are characterised by a high degree of seasonality. During winter soils are frozen and snow covers the surface preventing peat moss growth. Conversely, in summer, soils unfreeze and rain and evapotranspiration drive moss productivity. Although advances have been made in understanding growing season water balance and moss dynamics in northern peatlands, there remains a gap in knowledge of inter-seasonal water balance as layers of ice break up during the spring thaw. Understanding the effects of ice layers on spring water balance is important as this coincides with periods of high wildfire risk, such as the devastating Fort McMurrary wildfire of May, 2016. We hypothesise that shallow layers of ice disconnect the growing surface of moss from a falling water table, and prevent water from being supplied from depth. A disconnect between the evaporating surface and deeper water storage will lead to the drying out of the surface layer of moss and a greater risk of severe spring wildfires. We utilise the unsaturated flow model Hydrus 2D to explore water balance in peat layers with an impermeable layer representing ice. Additionally we create models to represent the heterogeneous break up of ice layers observed in Canadian boreal peatlands; these models explore the ability of breaks in an ice layer to connect the evaporating surface to a deeper water table. Results show that peatlands with slower rates of moss growth respond to dry periods by limiting evapotranspiration and thus maintain moist conditions in the sub-surface and a water table above the ice layer. Peatlands which are more productive continue to grow moss and evaporate during dry periods; this results in the near surface mosses drying out and the water table dropping below the level of the ice. Where there are breaks in the ice layer the evaporating surface is able to maintain contact with a falling water table, but connectivity is limited to above the breaks, with limited lateral transfer of water above the ice. Conceptually this means that peatlands which tend to have lower rates of growth are largely unaffected by the presence of a shallow ice layer in the early growing season, and are able to maintain moist sub-surface conditions in the absence of precipitation. They will thus be more resistant to severe wildfire. Conversely, peatlands which tend towards higher levels of moss productivity are able to maintain moss growth during dry periods. In the presence of an ice layer this greater productivity leads to a disconnection from deep water sources, extensive drying out of moss above the ice, and a greater susceptibility to severe wildfires. Our study gives important insights into the mechanisms behind heterogeneity in burning and depth of burn in northern peatland wildfires, as well as into burn heterogeneity within peatland microtopography.

Feeding soywaste or pellet on performance and carcass characteristics of post-weaning kids.

PubMed

Rahman, Mohammad Mijanur; Khadijah, Wan Embong Wan; Abdullah, Ramli Bin

2016-08-01

Twelve Jermasia kids were individually housed in pens to study the effects of soywaste on growth performance and carcass characteristics and to compare such effects with commercial pellet. Kids were divided into a pellet group and a soywaste group, including six kids (3 males and 3 females) in each group. Pellet or soywaste was offered to kids at a rate of 2.0 % dry matter (DM) of body weight/day in addition to Napier grass ad libitum. In last 10 days of experiment, kids were housed in metabolism crates for faeces collection. At the end of the experiment, three males from each group were slaughtered. Kids fed soywaste diet consumed more grass and neutral detergent fibre (NDF) than those fed pellet. The same trend was found for the digestibilities of DM, organic matter (OM) and NDF. Conversely, kids fed soywaste diet consumed less soywaste supplement than kids fed pellet. No treatment effects were observed on total intakes of DM, OM and crude protein (CP) including CP digestibility. Similarly, no effects were found on carcass and non-carcass components, except for lean, lean to fat ratio and kidney weight which were higher for kids fed soywaste diet. Results indicate that soywaste is effective as a feed for growing kids.

A Burst of Spring

NASA Image and Video Library

2010-03-10

In the winter a layer of carbon dioxide ice dry ice covers the north polar sand dunes as shown by NASA Mars Reconnaissance Orbiter. In the spring the sublimation of the ice going directly from ice to gas causes a host of uniquely Martian phenomena.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shahrukh, Hassan; Oyedun, Adetoyese Olajire; Kumar, Amit

In this study, a process model was developed to determine the net energy ratio (NER) for both regular and steam-pretreated pellet production from ligno-cellulosic biomass. NER is a ratio of the net energy output to the total net energy input from non-renewable energy source into the system. Scenarios were developed to measure the effect of temperature and level of steam pretreatment on the NER of both production processes. The NER for the base case at 6 kg h –1 is 1.29 and 5.0 for steam-pretreated and regular pellet production respectively. However, at the large scale NER would improve. The majormore » factor for NER is energy for steam and drying unit. The sensitivity analysis for the model shows that the optimum temperature for steam pretreatment is 200 °C with 50% pretreatment (Steam pretreating 50% feed stock, while the rest is undergoing regular pelletization). Uncertainty result for steam pretreated and regular pellet is 1.35 ± 0.09 and 4.52 ± 0.34 respectively.« less

Flocculation of high purity wheat straw soda lignin.

PubMed

Piazza, G J; Lora, J H; Garcia, R A

2014-01-01

In industrial process, acidification causes non-sulfonated lignin insolubility. The flocculants poly(diallyldimethylammonium chloride) (pDADMAC) and bovine blood (BB) also caused lignin insolubility while cationic polyacrylamide, chitosan, and soy protein PF 974 were ineffective. Turbidity determined optimal flocculant, but turbidity magnitude with BB was greater than expected. pDADMAC caused negative lignin Zeta potential to became positive, but BB-lignin Zeta potential was always negative. Insoluble lignin did not gravity sediment, and flocculant-lignin mixtures were centrifuged. Pellet and supernatant dry mass and corrected spectroscopic results were in good agreement for optimal pDADMAC and BB. Spectroscopy showed 87-92% loss of supernatant lignin. Nitrogen analysis showed BB concentrated in the pellet until the pellet became saturated with BB. Subtracting ash and BB mass from pellet and supernatant mass confirmed optimal BB. Low levels of alum caused increased lignin flocculation at lower levels of pDADMAC and BB, but alum did not affect optimal flocculant. Published by Elsevier Ltd.

Evaluation of conditioning time and temperature on gelatinized starch and vitamin retention in a pelleted swine diet.

PubMed

Lewis, L L; Stark, C R; Fahrenholz, A C; Bergstrom, J R; Jones, C K

2015-02-01

Two key feed processing parameters, conditioning temperature and time, were altered to determine their effects on concentration of gelatinized starch and vitamin retention in a pelleted finishing swine diet. Diet formulation (corn–soybean meal based with 30% distillers dried grains with solubles) was held constant. Treatments were arranged in a 2 × 3 factorial design plus a control with 2 conditioning temperatures (77 vs. 88°C) and 3 conditioner retention times (15, 30, and 60 s). In addition, a mash diet not subjected to conditioning served as a control for a total of 7 treatments. Samples were collected after conditioning but before pelleting (hot mash), after pelleting but before cooling (hot pellet), and after pelleting and cooling (cold pellet) and analyzed for percentage total starch, percentage gelatinized starch, and riboflavin, niacin, and vitamin D3 concentrations. Total percentage starch was increased by greater conditioning temperature (P = 0.041) but not time (P > 0.10), whereas higher temperature and longer time both increased (P < 0.05) percentage gelatinized starch, with increasing time resulting in a linear increase in percentage starch gelatinization (P = 0.013). The interaction between conditioning temperature and time increased percentage gelatinized starch (P = 0.003) but not percentage total starch (P > 0.10). Sample location also affected both percentage total starch and gelatinized starch (P < 0.05), with the greatest increase in percentage gelatinized starch occurring between hot mash and hot pellet samples. As expected, the pelleting process increased percentage gelatinized starch (P = 0.035; 7.3 vs. 11.7% gelatinized starch for hot mash vs. hot pellet samples, respectively), but there was no difference in total starch concentrations (P > 0.10). Finally, neither conditioning temperature nor time affected riboflavin, niacin, or vitamin D3 concentrations (P > 0.10). In summary, both increasing conditioningtemperature and time effect percentage gelatinized starch, but not to the extent of forcing the diet through a pelleting die.

Sorbent Structural Impacts Due to Humidity on Carbon Dioxide Removal Sorbents for Advanced Exploration Systems

NASA Technical Reports Server (NTRS)

Watson, David; Knox, James C.; West, Phillip; Stanley, Christine M.; Bush, Richard

2015-01-01

The Life Support Systems Project (LSSP) under the Advanced Exploration Systems (AES) program builds upon the work performed under the AES Atmosphere Resource Recovery and Environmental Monitoring (ARREM) project focusing on the numerous technology development areas. The CO2 removal and associated air drying development efforts are focused on improving the current state-of-the-art system on the International Space Station (ISS) utilizing fixed beds of sorbent pellets by seeking more robust pelletized sorbents, evaluating structured sorbents, and examining alternate bed configurations to improve system efficiency and reliability. A component of the CO2 removal effort encompasses structural stability testing of existing and emerging sorbents. Testing will be performed on dry sorbents and sorbents that have been conditioned to three humidity levels. This paper describes the sorbent structural stability screening efforts in support of the LSS Project within the AES Program.

Dust recycling technology in Kimitsu Works

NASA Astrophysics Data System (ADS)

Oda, Hiroshi; Ibaraki, Tetsuharu

Dust recycling technology by the rotary hearth furnace has been applied at Nippon Steel‧s Kimitsu Works since 2000. The dust and sludge with iron oxide and carbon are agglomerated into shaped articles and the iron oxide is reduced in a high temperature atmosphere. Zinc and other impurities in the dust and sludge are expelled and exhausted into off gas. The DRI pellets made from the dust and sludge have 70% metallization and are strong enough for being recycled to the blast furnaces. No.1 plant, which was constructed in May 2000 and has an agglomeration method of pelletizing, recycles mainly dry dusts. No.2 plant, which was constructed in December 2002 and has an agglomeration method of extrusion, recycles mainly sludge. The combination of the two plants is a solution for recycling various kinds of dusts and sludge emitted in a large scale steel works as Kimitsu Works

Quality by Design (QbD) Approach for Development of Co-Processed Excipient Pellets (MOMLETS) By Extrusion-Spheronization Technique.

PubMed

Patel, Hetal; Patel, Kishan; Tiwari, Sanjay; Pandey, Sonia; Shah, Shailesh; Gohel, Mukesh

2016-01-01

Microcrystalline cellulose (MCC) is an excellent excipient for the production of pellets by extrusion spheronization. However, it causes slow release rate of poorly water soluble drugs from pellets. Co-processed excipient prepared by spray drying (US4744987; US5686107; WO2003051338) and coprecipitation technique (WO9517831) are patented. The objective of present study was to develop co-processed MCC pellets (MOMLETS) by extrusion-spheronization technique using the principle of Quality by Design (QbD). Co-processed excipient core pellets (MOMLETS) were developed by extrusion spheronization technique using Quality by Design (QbD) approach. BCS class II drug (telmisartan) was layered onto it in a fluidized bed processor. Quality Target Product Profile (QTPP) and Critical Quality Attributes (CQA) for pellets were identified. Risk assessment was reported using Ishikawa diagram. Plackett Burman design was used to check the effect of seven independent variables; superdisintegrant, extruder speed, ethanol: water, spheronizer speed, extruder screen, pore former and MCC: lactose; on percentage drug release at 30 min. Pareto chart and normal probability plot was constructed to identify the significant factors. Box-Behnken design (BBD) using three most significant factors (Extruder screen size, type of superdisintegrant and type of pore former) was used as an optimization design. The control space was identified in which desired quality of the pellets can be obtained. Co-processed excipient core pellets (MOMLETS) were successfully developed by QbD approach. Versatility, Industrial scalability and simplicity are the main features of the proposed research. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Packin' ya Eskies!

PubMed

Bryce, Sharon; Taylor, Fiona; Shaw, Warwick

2010-08-01

The objective was to document a Process Validation on the packaging of human tissue grafts using polystyrene boxes containing dry ice for short term storage. The aim was to give a high degree of assurance that the processed grafts would be maintained at -20 degrees C for a period of time to allow distribution to customers. This study was designed to comply with the Australian GMP-Human Blood and Tissues and AATB Standards for Tissue Banking (Ed 12) American Association of Tissue Banks Section E4.141-Storage Conditions for Commonly Transplanted Human Tissue. Four Eskies were packed with 1, 4, 10 & 20 "dummy" allografts with thermocouples and Data Loggers attached with 3.5, 7, 15 and 20 kg of dry ice packed around the "dummy" allografts, respectively. All Eskies were weighed six times over a 48 h period and temperatures recorded. The results showed that one allograft in an Esky with 3.5 kg of dry ice was able to be stored for up to 31 h and fifteen allografts in an Esky containing 20 kg dry ice lasted 48 h.

In vitro fertilization and sperm cryopreservation in the black-footed cat (Felis nigripes) and sand cat (Felis margarita).

PubMed

Herrick, J R; Campbell, M; Levens, G; Moore, T; Benson, K; D'Agostino, J; West, G; Okeson, D M; Coke, R; Portacio, S C; Leiske, K; Kreider, C; Polumbo, P J; Swanson, W F

2010-03-01

Studies of in vitro fertilization (IVF) and sperm cryopreservation have been conducted in several small cat species, but virtually no data exist for black-footed cats (Felis nigripes) (BFCs) or sand cats (Felis margarita) (SCs). The objectives of this study were 1) to compare in vitro motility and acrosome status of fresh and cryopreserved (frozen in pellets on dry ice or in straws in liquid nitrogen vapor) BFC and SC spermatozoa cultured in feline-optimized culture medium (FOCM) or Ham F-10, 2) to assess ovarian responsiveness in BFCs and SCs following exogenous gonadotropin treatment and laparoscopic oocyte recovery, and 3) to evaluate the fertility of fresh and frozen-thawed spermatozoa from both species using homologous and heterologous (domestic cat oocytes) IVF in the two culture media. Motility and acrosomal integrity of fresh and frozen-thawed spermatozoa from BFCs and SCs were similar (P > 0.05) in both media during 6 h of culture. Although effects were more pronounced in SCs, cryopreservation in straws was superior (P < 0.05) to cryopreservation in pellets for both species. Gonadotropin stimulation produced approximately 16 ovarian follicles per female, and >80% of recovered oocytes were of optimal (grade 1) quality. The BFC and SC spermatozoa fertilized 60.0%-79.4% of homologous and 37.7%-42.7% of heterologous oocytes in both culture media, with increased (P < 0.05) cleavage of homologous (SC) and heterologous (BFC and SC) oocytes in FOCM. These results provide the first information to date on the gamete biology of two imperiled cat species and further our capacity to apply reproductive technologies for their conservation.

The development and in vitro evaluation of herbal pellets coated with Eudragit FS 30.

PubMed

Kaledaite, Rasa; Bernatoniene, Jurga; Dvořáčková, Kateřina; Gajdziok, Jan; Muselík, Jan; Pečiūra, Rimantas; Masteikova, Ruta

2014-05-20

Abstract The objective of this study was to prepare pellets of thyme (Thymus vulgaris L.), stinging nettle (Urtica dioica L.) and sage (Salvia officinalis L.) dry extracts by extrusion-spheronization technique to improve technological properties and investigate dissolution profiles of pellets covered different levels of pH-sensitive polymer Eudragit® FS. Optimal sample of pellets were prepared using microcrystalline cellulose and lactose as excipients and demonstrated excellent technological quality properties such as Hausner ratio (1.07 ± 0.11) and compressibility index (6.73 ± 0.94%) value, spericity (0.87 ± 0.001) and friability (0.22 ± 0.08 N). Pellets were coated by 10-35% (w/w) of Eudragit® FS. Dissolution studies showed that less than 20% of coating could not prevent dissolution of phenols in pH 1.2, 20% Eudragit® FS coating is enough to prevent herbal extract against dissolution in the stomach. There were observed no statistical significant differences between 20% and 25% or higher amount of coating polymer to a dissolution of phenols in low pH.

Slip resistance of winter footwear on snow and ice measured using maximum achievable incline.

PubMed

Hsu, Jennifer; Shaw, Robert; Novak, Alison; Li, Yue; Ormerod, Marcus; Newton, Rita; Dutta, Tilak; Fernie, Geoff

2016-05-01

Protective footwear is necessary for preventing injurious slips and falls in winter conditions. Valid methods for assessing footwear slip resistance on winter surfaces are needed in order to evaluate footwear and outsole designs. The purpose of this study was to utilise a method of testing winter footwear that was ecologically valid in terms of involving actual human testers walking on realistic winter surfaces to produce objective measures of slip resistance. During the experiment, eight participants tested six styles of footwear on wet ice, on dry ice, and on dry ice after walking over soft snow. Slip resistance was measured by determining the maximum incline angles participants were able to walk up and down in each footwear-surface combination. The results indicated that testing on a variety of surfaces is necessary for establishing winter footwear performance and that standard mechanical bench tests for footwear slip resistance do not adequately reflect actual performance. Practitioner Summary: Existing standardised methods for measuring footwear slip resistance lack validation on winter surfaces. By determining the maximum inclines participants could walk up and down slopes of wet ice, dry ice, and ice with snow, in a range of footwear, an ecologically valid test for measuring winter footwear performance was established.

Slip resistance of winter footwear on snow and ice measured using maximum achievable incline

PubMed Central

Hsu, Jennifer; Shaw, Robert; Novak, Alison; Li, Yue; Ormerod, Marcus; Newton, Rita; Dutta, Tilak; Fernie, Geoff

2016-01-01

Abstract Protective footwear is necessary for preventing injurious slips and falls in winter conditions. Valid methods for assessing footwear slip resistance on winter surfaces are needed in order to evaluate footwear and outsole designs. The purpose of this study was to utilise a method of testing winter footwear that was ecologically valid in terms of involving actual human testers walking on realistic winter surfaces to produce objective measures of slip resistance. During the experiment, eight participants tested six styles of footwear on wet ice, on dry ice, and on dry ice after walking over soft snow. Slip resistance was measured by determining the maximum incline angles participants were able to walk up and down in each footwear–surface combination. The results indicated that testing on a variety of surfaces is necessary for establishing winter footwear performance and that standard mechanical bench tests for footwear slip resistance do not adequately reflect actual performance. Practitioner Summary: Existing standardised methods for measuring footwear slip resistance lack validation on winter surfaces. By determining the maximum inclines participants could walk up and down slopes of wet ice, dry ice, and ice with snow, in a range of footwear, an ecologically valid test for measuring winter footwear performance was established. PMID:26555738

Estimation of Sintering Kinetics of Oxidized Magnetite Pellet Using Optical Dilatometer

NASA Astrophysics Data System (ADS)

Sandeep Kumar, T. K.; Viswanathan, Neelakantan Nurni; Ahmed, Hesham M.; Andersson, Charlotte; Björkman, Bo

2015-04-01

The quality of magnetite pellet is primarily determined by the physico-chemical changes the pellet undergoes as it makes excursion through the gaseous and thermal environment in the induration furnace. Among these physico-chemical processes, the oxidation of magnetite phase and the sintering of oxidized magnetite (hematite) and magnetite (non-oxidized) phases are vital. Rates of these processes not only depend on the thermal and gaseous environment the pellet gets exposed in the induration reactor but also interdependent on each other. Therefore, a systematic study should involve understanding these processes in isolation to the extent possible and quantify them seeking the physics. With this motivation, the present paper focusses on investigating the sintering kinetics of oxidized magnetite pellet. For the current investigation, sintering experiments were carried out on pellets containing more than 95 pct magnetite concentrate from LKAB's mine, dried and oxidized to completion at sufficiently low temperature to avoid sintering. The sintering behavior of this oxidized pellet is quantified through shrinkage captured by Optical Dilatometer. The extent of sintering characterized by sintering ratio found to follow a power law with time i.e., Kt n . The rate constant K for sintering was determined for different temperatures from isothermal experiments. The rate constant, K, varies with temperature as and the activation energy ( Q) and reaction rate constant ( K') are estimated. Further, the sintering kinetic equation was also extended to a non-isothermal environment and validated using laboratory experiments.

Odor, gaseous and PM10 emissions from small scale combustion of wood types indigenous to Central Europe

PubMed Central

Kistler, Magdalena; Schmidl, Christoph; Padouvas, Emmanuel; Giebl, Heinrich; Lohninger, Johann; Ellinger, Reinhard; Bauer, Heidi; Puxbaum, Hans

2012-01-01

In this study, we investigated the emissions, including odor, from log wood stoves, burning wood types indigenous to mid-European countries such as Austria, Czech Republic, Hungary, Slovak Republic, Slovenia, Switzerland, as well as Baden-Württemberg and Bavaria (Germany) and South Tyrol (Italy). The investigations were performed with a modern, certified, 8 kW, manually fired log wood stove, and the results were compared to emissions from a modern 9 kW pellet stove. The examined wood types were deciduous species: black locust, black poplar, European hornbeam, European beech, pedunculate oak (also known as “common oak”), sessile oak, turkey oak and conifers: Austrian black pine, European larch, Norway spruce, Scots pine, silver fir, as well as hardwood briquettes. In addition, “garden biomass” such as pine cones, pine needles and dry leaves were burnt in the log wood stove. The pellet stove was fired with softwood pellets. The composite average emission rates for log wood and briquettes were 2030 mg MJ−1 for CO; 89 mg MJ−1 for NOx, 311 mg MJ−1 for CxHy, 67 mg MJ−1 for particulate matter PM10 and average odor concentration was at 2430 OU m−3. CO, CxHy and PM10 emissions from pellets combustion were lower by factors of 10, 13 and 3, while considering NOx – comparable to the log wood emissions. Odor from pellets combustion was not detectable. CxHy and PM10 emissions from garden biomass (needles and leaves) burning were 10 times higher than for log wood, while CO and NOx rise only slightly. Odor levels ranged from not detectable (pellets) to around 19,000 OU m−3 (dry leaves). The odor concentration correlated with CO, CxHy and PM10. For log wood combustion average odor ranged from 536 OU m−3 for hornbeam to 5217 OU m−3 for fir, indicating a considerable influence of the wood type on odor concentration. PMID:23471123

Odor, gaseous and PM10 emissions from small scale combustion of wood types indigenous to Central Europe.

PubMed

Kistler, Magdalena; Schmidl, Christoph; Padouvas, Emmanuel; Giebl, Heinrich; Lohninger, Johann; Ellinger, Reinhard; Bauer, Heidi; Puxbaum, Hans

2012-05-01

In this study, we investigated the emissions, including odor, from log wood stoves, burning wood types indigenous to mid-European countries such as Austria, Czech Republic, Hungary, Slovak Republic, Slovenia, Switzerland, as well as Baden-Württemberg and Bavaria (Germany) and South Tyrol (Italy). The investigations were performed with a modern, certified, 8 kW, manually fired log wood stove, and the results were compared to emissions from a modern 9 kW pellet stove. The examined wood types were deciduous species: black locust, black poplar, European hornbeam, European beech, pedunculate oak (also known as "common oak"), sessile oak, turkey oak and conifers: Austrian black pine, European larch, Norway spruce, Scots pine, silver fir, as well as hardwood briquettes. In addition, "garden biomass" such as pine cones, pine needles and dry leaves were burnt in the log wood stove. The pellet stove was fired with softwood pellets. The composite average emission rates for log wood and briquettes were 2030 mg MJ -1 for CO; 89 mg MJ -1 for NO x , 311 mg MJ -1 for C x H y , 67 mg MJ -1 for particulate matter PM 10 and average odor concentration was at 2430 OU m -3 . CO, C x H y and PM 10 emissions from pellets combustion were lower by factors of 10, 13 and 3, while considering NO x - comparable to the log wood emissions. Odor from pellets combustion was not detectable. C x H y and PM10 emissions from garden biomass (needles and leaves) burning were 10 times higher than for log wood, while CO and NO x rise only slightly. Odor levels ranged from not detectable (pellets) to around 19,000 OU m -3 (dry leaves). The odor concentration correlated with CO, C x H y and PM 10 . For log wood combustion average odor ranged from 536 OU m -3 for hornbeam to 5217 OU m -3 for fir, indicating a considerable influence of the wood type on odor concentration.

Dueling Mechanisms for Dry Zones around Frozen Droplets

NASA Astrophysics Data System (ADS)

Bisbano, Caitlin; Nath, Saurabh; Boreyko, Jonathan

2016-11-01

Ice acts as a local humidity sink, due to its depressed saturation pressure relative to that of supercooled water. Hygroscopic chemicals typically exhibit annular dry zones of inhibited condensation; however, dry zones do not tend to form around ice because of inter-droplet frost growth to nearby liquid droplets that have already condensed on the chilled surface. Here, we use a humidity chamber with an embedded Peltier stage to initially suppress the growth of condensation on a chilled surface containing a single frozen droplet, in order to characterize the dry zone around ice for the first time. The length of the dry zone was observed to vary by at least two orders of magnitude as a function of surface temperature, ambient humidity, and the size of the frozen droplet. The surface temperature and ambient humidity govern the magnitudes of the in-plane and out-of-plane gradients in vapor pressure, while the size of the frozen droplet effects the local thickness of the concentration boundary layer. We develop an analytical model that reveals two different types of dry zones are possible: one in which nucleation is inhibited and one where the net growth of condensate is inhibited. Finally, a phase map was developed to predict the parameter space in which nucleation dry zones versus flux dry zones are dominant.

Flash Pyrolysis and Fractional Pyrolysis of Oleaginous Biomass in a Fluidized-bed Reactor

NASA Astrophysics Data System (ADS)

Urban, Brook

Thermochemical conversion methods such as pyrolysis have the potential for converting diverse biomass feedstocks into liquid fuels. In particular, bio-oil yields can be maximized by implementing flash pyrolysis to facilitate rapid heat transfer to the solids along with short vapor residence times to minimize secondary degradation of bio-oils. This study first focused on the design and construction of a fluidized-bed flash pyrolysis reactor with a high-efficiency bio-oil recovery unit. Subsequently, the reactor was used to perform flash pyrolysis of soybean pellets to assess the thermochemical conversion of oleaginous biomass feedstocks. The fluidized bed reactor design included a novel feed input mechanism through suction created by flow of carrier gas through a venturi which prevented plugging problems that occur with a more conventional screw feeders. In addition, the uniquely designed batch pyrolysis unit comprised of two tubes of dissimilar diameters. The bottom section consisted of a 1" tube and was connected to a larger 3" tube placed vertically above. At the carrier gas flow rates used in these studies, the feed particles remained fluidized in the smaller diameter tube, but a reduction in carrier gas velocity in the larger diameter "disengagement chamber" prevented the escape of particles into the condensers. The outlet of the reactor was connected to two Allihn condensers followed by an innovative packed-bed dry ice condenser. Due to the high carrier gas flow rates in fluidized bed reactors, bio-oil vapors form dilute aerosols upon cooling which that are difficult to coalesce and recover by traditional heat exchange condensers. The dry ice condenser provided high surface area for inertial impaction of these aerosols and also allowed easy recovery of bio-oils after natural evaporation of the dry ice at the end of the experiments. Single step pyrolysis was performed between 250-610°C with a vapor residence time between 0.3-0.6s. At 550°C or higher, 70% of the initial feed mass was recovered as bio-oil. However, the mass of high calorific lipid-derived components in the collected bio-oils remained nearly constant at reaction temperatures above 415°C; between 80-90% of the feedstock lipids were recovered in the bio-oil fraction. In addition, multi-step fractional flash pyrolysis experiments were performed to assess the possibility of producing higher quality bio-oils since a large fraction of protein and carbohydrates degrade at lower temperatures (320-400°C). A low temperature pyrolysis step was first performed and was followed by pyrolysis of the residues at higher temperature. This fractional pyrolysis approach which produced higher quality bio-oil with low water- and nitrogen- content from the higher temperature steps.

An experimental and theoretical study of the ice accretion process during artificial and natural icing conditions

NASA Technical Reports Server (NTRS)

Kirby, Mark S.; Hansman, R. John

1988-01-01

Real-time measurements of ice growth during artificial and natural icing conditions were conducted using an ultrasonic pulse-echo technique. This technique allows ice thickness to be measured with an accuracy of + or - 0.5 mm; in addition, the ultrasonic signal characteristics may be used to detect the presence of liquid on the ice surface and hence discern wet and dry ice growth behavior. Ice growth was measured on the stagnation line of a cylinder exposed to artificial icing conditions in the NASA Lewis Icing Research Tunnel (IRT), and similarly for a cylinder exposed in flight to natural icing conditions. Ice thickness was observed to increase approximately linearly with exposure time during the initial icing period. The ice accretion rate was found to vary with cloud temperature during wet ice growth, and liquid runback from the stagnation region was inferred. A steady-state energy balance model for the icing surface was used to compare heat transfer characteristics for IRT and natural icing conditions. Ultrasonic measurements of wet and dry ice growth observed in the IRT and in flight were compared with icing regimes predicted by a series of heat transfer coefficients. The heat transfer magnitude was generally inferred to be higher for the IRT than for the natural icing conditions encountered in flight. An apparent variation in the heat transfer magnitude was also observed for flights conducted through different natural icing-cloud formations.

Growth and Nutrient Utilization in Kids Fed Expander-extruded Complete Feed Pellets Containing Red Gram (Cajanus cajan) Straw

PubMed Central

Reddy, P. B.; Reddy, T. J.; Reddy, Y. R.

2012-01-01

A growth and digestibility study was conducted using Osmanabadi goat male kids by feeding complete diets in the form of mash or expander extruded pellets containing different levels of red gram (Cajanus cajan) straw (RGS). Two iso-nitrogenous complete diets were prepared by incorporating RGS at 35% and 50% levels. Half the quantity of each complete mash feed was then converted into pellets through expander extruder processing. Thirty two kids of 4 to 5 months age were divided into four groups of eight each and were fed for 150 d with four experimental diets (T1: mash with 35% RGS, T2: mash with 50% RGS, T3: pellets with 35% RGS and T4: pellets with 50% RGS). Pelleting of complete diets significantly (p<0.001) increased the voluntary feed intake (671.45 vs 426.28 g/d) at both levels of RGS in the feeds. Average daily gain (ADG, g/d) also increased significantly (p<0.001) from 48.79 in kids fed mash diet to 71.29 in those fed with pelleted diets. Feed conversion efficiency (dry matter (DM) intake: weight gain) was comparable among all the treatment groups. Digestibility of nutrients was not affected by pelleting of the feeds whereas, increasing the level of inclusion of RGS in feeds from 35% to 50% decreased (p<0.05) the digestibility of DM and crude protein (CP) resulting in lower (p<0.001) metabolizable energy (ME) content (MJ/kg DM) in feeds with 50% RGS (7.93 vs 8.75). Daily intake (MJ/kg BW−0.75) of ME decreased (p<0.05) in feeds containing 50% RGS while pelleting of feeds increased (p<0.05) the intake of DM, CP, digestible crude protein (DCP) and ME. It is inferred that expander extruder pelleting can efficiently utilize RGS up to 50% level in complete diets for growing goat kids. PMID:25049537

Growth and Nutrient Utilization in Kids Fed Expander-extruded Complete Feed Pellets Containing Red Gram (Cajanus cajan) Straw.

PubMed

Reddy, P B; Reddy, T J; Reddy, Y R

2012-12-01

A growth and digestibility study was conducted using Osmanabadi goat male kids by feeding complete diets in the form of mash or expander extruded pellets containing different levels of red gram (Cajanus cajan) straw (RGS). Two iso-nitrogenous complete diets were prepared by incorporating RGS at 35% and 50% levels. Half the quantity of each complete mash feed was then converted into pellets through expander extruder processing. Thirty two kids of 4 to 5 months age were divided into four groups of eight each and were fed for 150 d with four experimental diets (T1: mash with 35% RGS, T2: mash with 50% RGS, T3: pellets with 35% RGS and T4: pellets with 50% RGS). Pelleting of complete diets significantly (p<0.001) increased the voluntary feed intake (671.45 vs 426.28 g/d) at both levels of RGS in the feeds. Average daily gain (ADG, g/d) also increased significantly (p<0.001) from 48.79 in kids fed mash diet to 71.29 in those fed with pelleted diets. Feed conversion efficiency (dry matter (DM) intake: weight gain) was comparable among all the treatment groups. Digestibility of nutrients was not affected by pelleting of the feeds whereas, increasing the level of inclusion of RGS in feeds from 35% to 50% decreased (p<0.05) the digestibility of DM and crude protein (CP) resulting in lower (p<0.001) metabolizable energy (ME) content (MJ/kg DM) in feeds with 50% RGS (7.93 vs 8.75). Daily intake (MJ/kg BW(-0.75)) of ME decreased (p<0.05) in feeds containing 50% RGS while pelleting of feeds increased (p<0.05) the intake of DM, CP, digestible crude protein (DCP) and ME. It is inferred that expander extruder pelleting can efficiently utilize RGS up to 50% level in complete diets for growing goat kids.

Photogrammetric Measurement of Recession Rates of Low Temperature Ablators Subjected to High Speed Flow

DTIC Science & Technology

2011-06-01

recession rate prediction of carbon based, camphor and dry ice at hypersonic velocities...paradichlorobenzene, naphthalene, camphor , and ammonium chloride (Kohlman & Richardson, 1969). Except for dry ice, these materials require stagnation temperatures... Camphor , for example, sublimates at ~170C. With the reestablished interest in expendable ablative heat shields, these past experiences have

75 FR 67258 - Position Reports for Physical Commodity Swaps

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-02

... Cattle. CME Milk Class III. Comex (``CMX'') Copper Grade 1. CMX Gold. CMX Silver. ICE Futures US (``ICUS... Oats. CME Butter. CME Cheese. CME Dry Whey. CME Hardwood Pulp. CME Lean Hogs. CME Non Fat Dry Milk. CME... contract--The ICE WTI Average Price Option is indirectly linked to a 20.2 listed futures contract because...

Perspective of Life Search in Martian Econiches

NASA Astrophysics Data System (ADS)

Demidov, N. E.

2017-05-01

Mars may be divided on five ecological niches according to presence and state of water: permanent polar caps, dry regolith, subpermafrost aquifers, cryopegs and ice containing regolith. Basic limiting factors for the search of life in this econiches are: absence of water (dry regolith), depth of burial (cryopegs and subpermafrost aquifers), age (ice containing permafrost and polar caps). High priority targets for the search of life on Mars are represented by permanently frozen deposits of young polar volcanoes and ash layers in polar caps. During volcanic eruptions microorganisms from subpermafrost aquifers could propagate to the surface and survive in permafrost or ice for million years, as it is known to happen on Earth. Possibility of specific lithic habitats in dry layer must also be taken into account.

Mudstone sedimentation at high latitudes: Ice as a transport medium for mud and supplier of nutrients

USGS Publications Warehouse

Macquaker, J.H.S.; Keller, M.A.

2005-01-01

Controls on mudstone deposition at high latitudes are poorly known relative to low latitudes. In recent sediments deposited in these environments, ice significantly influences sediment transport and primary productivity. The products of ice transport are relatively well known in glacimarine settings, but are less well known from below melting sea ice. This latter setting is significant as today it is associated with high primary organic productivity. The aim of this study is to assess how sea ice might have controlled lithofacies variability and organic-matter distribution and preservation in an ancient marine, siliciclastic mudstone-dominated succession deposited at high latitudes. Combined sedimentary logging, optical and electron optical (back-scatte red electron imagery), geochemical, and isotopic methods were used to determine sample variability in forty-five samples collected from the Lower Cretaceous succession in the Mikkelsen Bay State #1 borehole (North Slope, Alaska). The succession overall fines upward and contains muddy sandstones and sand- and silt-bearing, clay-rich mudstones towards its base in contrast to clay-rich and clay-dominated mudstones towards its top. Some of the mudstone units exhibit thin (< 5 mm), relic-beds that fine upward weakly. In some units small (0.5 mm), bed-parallel silt-filled microburrows disrupt depositional laminae whereas in others pervasive burrowing completely obliterates original depositional textures. Many of the units are pelleted. These mudstones are unusual in that they contain minor but very striking outsize grains, composed of subrounded to rounded sand and granule-size material. In addition, they are good petroleum source rocks, with between 2.8 and 5.9 wt % total organic carbon, of predominantly Type II kerogen. The organic matter has an isotopic signature ranging from -25.4??? ??13C to -28.1??? ??13C. Thin tuffs (< 20 mm) and carbonate-cemented units are also present. Given the absence of significant polar ice in the Early Cretaceous the outsized grains are interpreted to have been deposited from a combination of melting, dirty anchor, and fast ice. The mud fraction, which forms the bulk of the sediment, is interpreted to have been deposited from melting, sediment-laden frazil ice, and fast ice. After deposition sediments were partially reworked by bottom currents generated by brine rejection during sea ice formation. Sympagic organisms, grazing on algae and bacteria both within and below the ice, pelleted the sediment. Bioturbation, which varies through the succession, indicates that sedimentation probably occurred beneath a predominantly oxic or dysoxic water column. In this setting productivity was fueled by nutrients released from melting sea ice in the marginal ice zone. The good petroleum source potential of these mudstones is attributed to high organic productivity coupled to episodic and rapid sedimentation rather than existence of bottom-water anoxia linked to upwelling. Because sea-ice rafting was probably the dominant sediment transport mechanism it is not appropriate to use sequence stratigraphic methodology to predict lithofacies variability in this environment. Copyright ?? 2005, SEPM (Society for Sedimentary Geology).

Review of the Aerodynamic Acceptance Test and Application to Anti-Icing Fluids Testing in the NRC Propulsion and Icing Wind Tunnel

NASA Technical Reports Server (NTRS)

Broeren, Andy P.; Riley, James T.

2012-01-01

In recent years, the FAA has worked with Transport Canada, National Research Council of Canada (NRC) and APS Aviation, Inc. to develop allowance times for aircraft operations in ice-pellet precipitation. These allowance times are critical to ensure safety and efficient operation of commercial and cargo flights. Wind-tunnel testing with uncontaminated anti-icing fluids and fluids contaminated with simulated ice-pellets had been carried out at the NRC Propulsion and Icing Wind Tunnel (PIWT) to better understand the flowoff characteristics and resulting aerodynamic effects. The percent lift loss on the thin, high-performance wing model tested in the PIWT was determined at 8 angle of attack and used as one of the evaluation criteria in determining the allowance times. Because it was unclear as to how performance degradations measured on this model were relevant to an actual airplane configuration, some means of interpreting the wing model lift loss was deemed necessary. In this report, the lift loss was related to the loss in maximum lift of a Boeing 737-200ADV airplane through the Aerodynamic Acceptance Test (AAT) performed for fluids qualification. This report provides a review of the research basis of the AAT in order to understand how this correlation was applied. A loss in maximum lift coefficient of 5.24 percent on the B737-200ADV airplane (which was adopted as the threshold in the AAT) corresponds to a lift loss of 7.3 percent on the PIWT model at 8 degrees angle of attack. There is significant scatter in the data used to develop the correlation related to varying effects of the various antiicing fluids that were tested and other factors. A statistical analysis indicated the upper limit of lift loss on the PIWT model was 9.2 percent. Therefore, for cases resulting in PIWT model lift loss from 7.3 to 9.2 percent, extra scrutiny of the visual observations is required in evaluating fluid performance with contamination. Additional research may result in future changes to this correlation.

Dynamic Ocular Surface and Lacrimal Gland Changes Induced in Experimental Murine Dry Eye

PubMed Central

Xiao, Bing; Wang, Yu; Reinach, Peter S.; Ren, Yueping; Li, Jinyang; Hua, Shanshan; Lu, Huihui; Chen, Wei

2015-01-01

Dry eye disease can be a consequence of lacrimal gland insufficiency in Sjögren’s Syndrome or increased tear film evaporation despite normal lacrimal gland function. To determine if there is a correlation between severity effects in these models and underlying pathophysiological responses, we compared the time dependent changes in each of these parameters that occur during a 6 week period. Dry eye was induced in 6-week-old female C57BL/6 mice by exposing them to an Intelligently Controlled Environmental System (ICES). Sixty mice were housed in ICES for 1, 2, 4 and 6 weeks respectively. Twelve were raised in normal environment and received subcutaneous injections of scopolamine hydrobromide (SCOP) 3 times daily for 5 days. Another sixty mice were housed in a normal environment and received no treatment. Corneal fluorescein staining along with corneal MMP-9 and caspase-3 level measurements were performed in parallel with the TUNEL assay. Interleukin-17(IL-17), IL-23, IL-6, IL-1, TNF-α, IFN-γ and TGF-β2 levels were estimated by real-time PCR measurements of conjunctival and lacrimal gland samples (LGs). Immunohistochemistry of excised LGs along with flow cytometry in cervical lymph nodes evaluated immune cell infiltration. Light and transmission electron microscopy studies evaluated LGs cytoarchitectural changes. ICES induced corneal epithelial destruction and apoptosis peaked at 2 weeks and kept stable in the following 4 weeks. In the ICES group, lacrimal gland proinflammatory cytokine level increases were much lower than those in the SCOP group. In accord with the lower proinflammatory cytokine levels, in the ICES group, lacrimal gland cytosolic vesicular density and size exceeded that in the SCOP group. ICES and SCOP induced murine dry eye effects became progressively more severe over a two week period. Subsequently, the disease process stabilized for the next four weeks. ICES induced local effects in the ocular surface, but failed to elicit lacrimal gland inflammation and cytoarchitectural changes, which accounts for less dry eye severity in the ICES model than that in the SCOP model. PMID:25590134

Dynamic ocular surface and lacrimal gland changes induced in experimental murine dry eye.

PubMed

Xiao, Bing; Wang, Yu; Reinach, Peter S; Ren, Yueping; Li, Jinyang; Hua, Shanshan; Lu, Huihui; Chen, Wei

2015-01-01

Dry eye disease can be a consequence of lacrimal gland insufficiency in Sjögren's Syndrome or increased tear film evaporation despite normal lacrimal gland function. To determine if there is a correlation between severity effects in these models and underlying pathophysiological responses, we compared the time dependent changes in each of these parameters that occur during a 6 week period. Dry eye was induced in 6-week-old female C57BL/6 mice by exposing them to an Intelligently Controlled Environmental System (ICES). Sixty mice were housed in ICES for 1, 2, 4 and 6 weeks respectively. Twelve were raised in normal environment and received subcutaneous injections of scopolamine hydrobromide (SCOP) 3 times daily for 5 days. Another sixty mice were housed in a normal environment and received no treatment. Corneal fluorescein staining along with corneal MMP-9 and caspase-3 level measurements were performed in parallel with the TUNEL assay. Interleukin-17(IL-17), IL-23, IL-6, IL-1, TNF-α, IFN-γ and TGF-β2 levels were estimated by real-time PCR measurements of conjunctival and lacrimal gland samples (LGs). Immunohistochemistry of excised LGs along with flow cytometry in cervical lymph nodes evaluated immune cell infiltration. Light and transmission electron microscopy studies evaluated LGs cytoarchitectural changes. ICES induced corneal epithelial destruction and apoptosis peaked at 2 weeks and kept stable in the following 4 weeks. In the ICES group, lacrimal gland proinflammatory cytokine level increases were much lower than those in the SCOP group. In accord with the lower proinflammatory cytokine levels, in the ICES group, lacrimal gland cytosolic vesicular density and size exceeded that in the SCOP group. ICES and SCOP induced murine dry eye effects became progressively more severe over a two week period. Subsequently, the disease process stabilized for the next four weeks. ICES induced local effects in the ocular surface, but failed to elicit lacrimal gland inflammation and cytoarchitectural changes, which accounts for less dry eye severity in the ICES model than that in the SCOP model.

Effect of dried rumen digesta pellet levels on feed use, rumen ecology, and blood metabolite in swamp buffalo.

PubMed

Seankamsorn, Anuthida; Cherdthong, Anusorn; Wanapat, Metha; Supapong, Chanadol; Khonkhaeng, Benjamad; Uriyapongson, Sutipong; Gunun, Nirawan; Gunun, Pongsatron; Chanjula, Pin

2017-01-01

The aim of this experiment was to determine the effect of dried rumen digesta pellet levels on feed intake, digestibility, rumen ecology, and blood metabolites in swamp buffalo. Four 2-year-old male swamp buffalo with an initial body weight (BW) of 150 ± 10.0 kg were randomly assigned according to a 4 × 4 Latin square design to receive four levels of dried rumen digesta pellets (DRDPs). The dietary treatments were supplementation of DRDP at 0, 50, 100, and 150 g dry matter/day, respectively. Total feed intake was significantly different among treatments (p < 0.05) and was highest in the 150 g/day DRDP supplement (2.68 kg/day). Intakes of neutral detergent fiber (NDF) and acid detergent fiber did not affect DRDP levels, while intakes of organic matter and crude protein (CP) were altered significantly when 150 g of DRDP was used (p < 0.05). Buffalo fed with DRDP at 150 g/day had the highest CP and NDF digestibility (p < 0.05). DRDP supplementation did not affect rumen pH, and temperature and the concentration of ruminal ammonia-nitrogen and blood urea nitrogen were not altered among the treatments. The mean value of fungal zoospores in the buffalo was significantly different among treatments and was highest in supplementation with DRDP at 150 g. The mean value of propionic acid was significantly different at various levels of DRDP; it was highest in the group fed with 150 g DRDP (p < 0.05). Thus, supplementation of DRDP at 150 g improved feed use and increased fungal zoospore population. In addition, DRDP feeding is recommended, since it has positive economic impacts and helps control environmental pollution.

7 CFR 91.20 - Shipping.

Code of Federal Regulations, 2013 CFR

2013-01-01

... refrigerated samples should contain ice or ice packs to maintain temperatures of 0° to 5 °C, unless a different temperature is required for the sample to be tested. (d) Containers for frozen samples should contain dry ice...

7 CFR 91.20 - Shipping.

Code of Federal Regulations, 2012 CFR

2012-01-01

... refrigerated samples should contain ice or ice packs to maintain temperatures of 0° to 5 °C, unless a different temperature is required for the sample to be tested. (d) Containers for frozen samples should contain dry ice...

7 CFR 91.20 - Shipping.

Code of Federal Regulations, 2014 CFR

2014-01-01

... refrigerated samples should contain ice or ice packs to maintain temperatures of 0° to 5 °C, unless a different temperature is required for the sample to be tested. (d) Containers for frozen samples should contain dry ice...

7 CFR 91.20 - Shipping.

Code of Federal Regulations, 2011 CFR

2011-01-01

... refrigerated samples should contain ice or ice packs to maintain temperatures of 0° to 5 °C, unless a different temperature is required for the sample to be tested. (d) Containers for frozen samples should contain dry ice...

7 CFR 91.20 - Shipping.

Code of Federal Regulations, 2010 CFR

2010-01-01

... refrigerated samples should contain ice or ice packs to maintain temperatures of 0° to 5 °C, unless a different temperature is required for the sample to be tested. (d) Containers for frozen samples should contain dry ice...

SINGLE-STEP CONVERSION OF UO$sub 3$ TO UF$sub 4$

DOEpatents

Moore, J.E.

1960-07-12

A description is given of the preparation of uranium tetrafluoride by reacting a hexavalent uranium compound with a pclysaccharide and gaseous hydrogen fluoride at an elevated temperature. Uranium trioxide and starch are combined with water to form a doughy mixture. which is extruded into pellets and dried. The pellets are then contacted with HF at a temperature from 500 to 700 deg C in a moving bed reactor to prcduce UF/sub 4/. Reduction of the hexavalent uranium to UO/sub 2/ and conversion of the UO/sub 2/ to UF/sub 4/ are accomplished simultaneously in this process.

21 CFR 880.6050 - Ice bag.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ice bag. 880.6050 Section 880.6050 Food and Drugs....6050 Ice bag. (a) Identification. An ice bag is a device intended for medical purposes that is in the form of a container intended to be filled with ice that is used to apply dry cold therapy to an area of...

21 CFR 880.6050 - Ice bag.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ice bag. 880.6050 Section 880.6050 Food and Drugs....6050 Ice bag. (a) Identification. An ice bag is a device intended for medical purposes that is in the form of a container intended to be filled with ice that is used to apply dry cold therapy to an area of...

21 CFR 880.6050 - Ice bag.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ice bag. 880.6050 Section 880.6050 Food and Drugs....6050 Ice bag. (a) Identification. An ice bag is a device intended for medical purposes that is in the form of a container intended to be filled with ice that is used to apply dry cold therapy to an area of...

21 CFR 880.6050 - Ice bag.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ice bag. 880.6050 Section 880.6050 Food and Drugs....6050 Ice bag. (a) Identification. An ice bag is a device intended for medical purposes that is in the form of a container intended to be filled with ice that is used to apply dry cold therapy to an area of...

21 CFR 880.6050 - Ice bag.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ice bag. 880.6050 Section 880.6050 Food and Drugs....6050 Ice bag. (a) Identification. An ice bag is a device intended for medical purposes that is in the form of a container intended to be filled with ice that is used to apply dry cold therapy to an area of...

A Molecular Explanation of How the Fog Is Produced When Dry Ice Is Placed in Water

ERIC Educational Resources Information Center

Kuntzleman, Thomas S.; Ford, Nathan; No, Jin-Hwan; Ott, Mark E.

2015-01-01

Everyone enjoys seeing the cloudy white fog generated when solid carbon dioxide (dry ice) is placed in water. Have you ever wondered what physical and chemical processes occur to produce this fog? When asked this question, many chemical educators suggest that the fog is produced when atmospheric water vapor condenses on cold carbon dioxide gas…

Comparison of volatiles and mosquito capture efficacy for three carbohydrate sources in a yeast-fermentation CO2 generator

USDA-ARS?s Scientific Manuscript database

Mosquito surveillance in remote areas with limited access to canisters of CO2 or dry ice will benefit from an effective alternative CO2 source. In this study, we document the differences in mosquito and non-mosquito capture rates from CO2 baited (dry ice or yeast fermentation of carbohydrates) CDC t...

A New Freezing Method Using Pre-Dehydration by Microwave-Vacuum Drying

NASA Astrophysics Data System (ADS)

Tsuruta, Takaharu; Hamidi, Nurkholis

Partial dehydration by microwave-vacuum drying has been applied to tuna and strawberry in order to reduce cell-damages caused by the formation of large ice-crystals during freezing. The samples were subjected to microwave vacuum drying at pressure of 5 kPa and temperature less than 27°C to remove small amount of water prior to freezing. The tuna were cooled by using the freezing chamber at temperature -50°C or -150°C, while the strawberries were frozen at temperature -30°C or -80°C, respectively. The temperature transients in tuna showed that removing some water before freezing made the freezing time shorter. The observations of ice crystal clearly indicated that rapid cooling and pre-dehydration prior to freezing were effective in minimizing the size of ice crystal. It is also understood that the formation of large ice crystals has a close relation to the cell damages. After thawing, the observation of microstructure was done on the tuna and strawberry halves. The pre-dehydrated samples showed a better structure than the un-dehydrated one. It is concluded that the pre-dehydration by microwave-vacuum drying is one promising method for the cryo-preservation of foods.

Glacier advance during Marine Isotope Stage 11 in the McMurdo Dry Valleys of Antarctica

PubMed Central

Swanger, Kate M.; Lamp, Jennifer L.; Winckler, Gisela; Schaefer, Joerg M.; Marchant, David R.

2017-01-01

We mapped six distinct glacial moraines alongside Stocking Glacier in the McMurdo Dry Valleys, Antarctica. Stocking Glacier is one of several alpine glaciers in the Dry Valleys fringed by multiple cold-based drop moraines. To determine the age of the outermost moraine, we collected 10 boulders of Ferrar Dolerite along the crest of the moraine and analyzed mineral separates of pyroxene for cosmogenic 3He. On the basis of these measurements, the exposure age for the outermost moraine is 391 ± 35 ka. This represents the first documented advance of alpine glacier ice in the Dry Valleys during Marine Isotope Stage (MIS) 11. At this time, Stocking Glacier was ~20–30% larger than today. The cause of ice expansion is uncertain, but most likely it is related to increased atmospheric temperature and precipitation, associated with reduced ice extent in the nearby Ross Embayment. The data suggest complex local environmental response to warm climates in Antarctica and have implications for glacial response to Holocene warming. The study also demonstrates the potential for using alpine glacier chronologies in the Transantarctic Mountains as proxies for retreat of grounded glacier ice in the Ross Embayment. PMID:28139676

Development of a two-stage light gas gun to accelerate hydrogen pellets to high speeds for plasma fueling applications

NASA Astrophysics Data System (ADS)

Combs, S. K.; Milora, S. L.; Foust, C. R.; Gouge, M. J.; Fehling, D. T.; Sparks, D. O.

1988-08-01

The development of a two-stage light gas gun to accelerate hydrogen isotope pellets to high speeds is under way at Oak Ridge National Laboratory. High velocities are desirable for plasma fueling applications, since the faster pellets can penetrate more deeply into large, hot plasmas and deposit atoms of fuel directly in a larger fraction of the plasma volume. In the initial configuration of the two-stage device, a 2.2-l volume provides the gas to accelerate a 25.4-mm-diam piston in a 1-m-long pump tube; a burst disk or a fast valve initiates the acceleration process in the first stage. As the piston travels the length of the pump tube, the downstream gas is compressed (to pressures up to 2600 bar) and thus is driven to high temperature (approx. 5000 K). This provides the driving force for acceleration of a 4-mm pellet in a 1-m-long gun barrel. In preliminary tests using helium as the driver in both stages, 35-mg plastic pellets have been accelerated to speeds as high as 3.8 km/s. Projectiles composed of hydrogen ice will have a mass in the range from 5 to 20 mg. However, the use of sabots to encase and protect the cryogenic pellets from the high peak pressures will probably be required to realize speeds of approx. 3 km/s or greater. The experimental plan includes acceleration of hydrogen isotopes as soon as the gun geometry and operating parameters are optimized; theoretical models are being used to aid in this process. The hardware is being designed to accommodate repetitive operation, which is the objective of this research and is required for future applications.

46 CFR 148.245 - Direct reduced iron (DRI); lumps, pellets, and cold-molded briquettes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the concentration of fines (pieces less than 6.35mm in size) in any one location in the cargo hold. (h) Radar and RDF scanners must be protected against the dust generated during cargo transfer operations of...

46 CFR 148.245 - Direct reduced iron (DRI); lumps, pellets, and cold-molded briquettes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the concentration of fines (pieces less than 6.35mm in size) in any one location in the cargo hold. (h) Radar and RDF scanners must be protected against the dust generated during cargo transfer operations of...

46 CFR 148.245 - Direct reduced iron (DRI); lumps, pellets, and cold-molded briquettes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the concentration of fines (pieces less than 6.35mm in size) in any one location in the cargo hold. (h) Radar and RDF scanners must be protected against the dust generated during cargo transfer operations of...

Pelleting in Associated with Sodium Monensin Increases the Conjugated Linoleic Acids Concentration in the Milk of Dairy Cows Fed Canola Seeds

PubMed Central

De Marchi, Francilaine Eloise; Romero, Jakeline Vieira; Damasceno, Julio Cesar; Grande, Paula Adriana; Zeoula, Lúcia Maria; dos Santos, Geraldo Tadeu

2015-01-01

To evaluate the effects of the pelleting and the addition of sodium monensin on production, the chemical and lipid composition of milk and butter physical characteristics, 4 Holstein dairy cows (135 days of lactation) with an average milk production of 14.7 kg/d, were supplemented with a concentrate containing ground canola seeds. The cows were assigned to a 4×4 Latin square design with a 2×2 factorial arrangement of treatments: i) ground maize, soybean meal, mineral and vitamin supplements, and ground canola seeds (CG); ii) CG concentrate with 31.5 mg of monensin added per kg of dry matter (DM); iii) CG pelleted concentrate; iv) CG concentrate with monensin addition pelleted. There was no difference in milk production and composition. The addition of monensin increased milk concentration of polyunsaturated fatty acids (PUFA), the PUFA/saturated fatty acids (SFA) ratio, and omega 6. The pelleting increased the concentration of monounsaturated fatty acids, the PUFA/SFA ratio, and the omega 6/omega 3 ratio, but decreased the concentration of SFA. The association between pelleting and the addition of monensin increased the concentration of conjugated linoleic acids by 46.9%. The physical characteristics of butter were not affected by the evaluated diets. We concluded that the concentrate with 31.5 mg of monensin added per kg DM basis combined with the pelleting improves the lipid composition of milk from Holstein cows that are on pasture and supplemented with ground canola seeds, without changing the production, milk composition, and spreadability of butter. PMID:26104517

DEVELOPMENT OF A CALCIUM-BASED SORBENT FOR HOT GAS CLEANUP

DOE Office of Scientific and Technical Information (OSTI.GOV)

T.D. Wheelock; L.K. Doraiswamy; K. Constant

1999-10-01

The development and testing of potential calcium-based sorbents for hot gas cleanup continued. One of the most promising materials combines powdered limestone and a calcium aluminate cement by two step pelletization followed by steam curing. Reasonably strong pellets are produced with good adsorption characteristics by incorporating 20 wt.% cement in the core and 40 wt.% cement in the shell. The resulting 4.76 mm diameter pellets are capable of withstanding a crushing force approaching 11.5 N/mm before breaking and are also capable of removing H{sub 2}S from dilute, hot gas streams. The pellets are also regenerable and reusable. Another promising materialmore » combines calcium carbonate powder and finely ground calcined alumina in tablet form. The small tablets are prepared by mixing the materials with water to form a thick paste which is then molded and dried. The tablets are hardened by calcining at either 1000 to 1100 C. The resulting tablets are strong and capable of removing H{sub 2}S from a dilute, hot gas stream.« less

Comparison of Dry Medium Culture Plates for Mesophilic Aerobic Bacteria in Milk, Ice Cream, Ham, and Codfish Fillet Products

PubMed Central

Park, Junghyun; Kim, Myunghee

2013-01-01

This study was performed to compare the performance of Sanita-Kun dry medium culture plate with those of traditional culture medium and Petrifilm dry medium culture plate for the enumeration of the mesophilic aerobic bacteria in milk, ice cream, ham, and codfish fillet. Mesophilic aerobic bacteria were comparatively evaluated in milk, ice cream, ham, and codfish fillet using Sanita-Kun aerobic count (SAC), Petrifilm aerobic count (PAC), and traditional plate count agar (PCA) media. According to the results, all methods showed high correlations of 0.989~1.000 and no significant differences were observed for enumerating the mesophilic aerobic bacteria in the tested food products. SAC method was easier to perform and count colonies efficiently as compared to the PCA and PAC methods. Therefore, we concluded that the SAC method offers an acceptable alternative to the PCA and PAC methods for counting the mesophilic aerobic bacteria in milk, ice cream, ham, and codfish fillet products. PMID:24551829

Testing of the Prototype Mars Drill and Sample Acquisition System in the Mars Analog Site of the Antarctica's Dry Valleys

NASA Astrophysics Data System (ADS)

Zacny, K.; Paulsen, G.; McKay, C.; Glass, B. J.; Marinova, M.; Davila, A. F.; Pollard, W. H.; Jackson, A.

2011-12-01

We report on the testing of the one meter class prototype Mars drill and cuttings sampling system, called the IceBreaker in the Dry Valleys of Antarctica. The drill consists of a rotary-percussive drill head, a sampling auger with a bit at the end having an integrated temperature sensor, a Z-stage for advancing the auger into the ground, and a sampling station for moving the augered ice shavings or soil cuttings into a sample cup. In November/December of 2010, the IceBreaker drill was tested in the Uni-versity Valley (within the Beacon Valley region of the Antarctic Dry Valleys). University Valley is a good analog to the Northern Polar Regions of Mars because a layer of dry soil lies on top of either ice-cemeted ground or massive ice (depending on the location within the valley). That is exactly what the 2007 Phoenix mission discovered on Mars. The drill demonstrated drilling in ice-cemented ground and in massive ice at the 1-1-100-100 level; that is the drill reached 1 meter in 1 hour with 100 Watts of power and 100 Newton Weight on Bit. This corresponds to an average energy of 100 Whr. At the same time, the bit temperature measured by the bit thermocouple did not exceed more than 10 °C above the formation temperature. The temperature also never exceeded freezing, which minimizes chances of getting stuck and also of altering the materials that are being sampled and analyzed. The samples in the forms of cuttings were acquired every 10 cm intervals into sterile bags. These tests have shown that drilling on Mars, in ice cemented ground with limited power, energy and Weight on Bit, and collecting samples in discrete depth intervals is possible within the given mass, power, and energy levels of a Phoenix-size lander and within the duration of a Phoenix-like mission.

Variable food absorption by Antarctic krill: Relationships between diet, egestion rate and the composition and sinking rates of their fecal pellets

NASA Astrophysics Data System (ADS)

Atkinson, A.; Schmidt, K.; Fielding, S.; Kawaguchi, S.; Geissler, P. A.

2012-01-01

The kinetics of food processing by zooplankton affects both their energy budgets and the biogeochemical fate of their fecal pellets. We sampled 40 schools of krill across the Scotia Sea during spring, summer and autumn and found that in all 3 seasons, every aspect of their absorption and defecation varied greatly. The C content of fecal pellets varied from 0.85% to 29% of their dry mass (median 9.8%) and C egestion rates varied 75-fold. C:N mass ratios of pellets ranged from 4.9 to 13.2 (median 7.8), higher than values of 3.9 in the krill and 5.4 in their food, pointing to enhanced uptake of N. Pellet sinking rates equated to 27-1218 m d -1 (median 304 m d -1), being governed mainly by pellet diameter (80-600 μm, mean 183 μm) and density (1.038-1.391 g cm -3, mean 1.121 g cm -3). Pellets showed little loss of C or N in filtered seawater over the first 2 days and were physically robust. When feeding rates were low, slow gut passage time and high absorption efficiency resulted in low egestion rates of pellets that were low in C and N content. These pellets were compact, dense and fast-sinking. Conversely, in good feeding conditions much food tended to pass quickly through the gut and was not efficiently absorbed, producing C and N-rich, slow-sinking pellets. Such "superfluous feeding" probably maximises the absolute rates of nutrient absorption. Food composition was also important: diatom-rich diets depressed the C content of the pellets but increased their sinking rates, likely due to silica ballasting. So depending on how krill process food, their pellets could represent both vehicles for rapid export and slow sinking, C and N-rich food sources for pelagic scavengers. C egestion rates by krill averaged 3.4% of summer primary production (and ingestion rates would be 2-10-fold higher than this) so whatever the fate of the pellets, krill are an important re-packager within the food web. While salp pellets tend to sink faster than those of krill, it is the latter that tend to prevail in sediment traps. We suggest that this is because krill schools are more compact, producing "rain showers" of pellets that exceed the capacity of pelagic scavengers to reprocess them.

How the user can influence particulate emissions from residential wood and pellet stoves: Emission factors for different fuels and burning conditions

NASA Astrophysics Data System (ADS)

Fachinger, Friederike; Drewnick, Frank; Gieré, Reto; Borrmann, Stephan

2017-06-01

For a common household wood stove and a pellet stove we investigated the dependence of emission factors for various gaseous and particulate pollutants on burning phase, burning condition, and fuel. Ideal and non-ideal burning conditions (dried wood, under- and overload, small logs, logs with bark, excess air) were used. We tested 11 hardwood species (apple, ash, bangkirai, birch, beech, cherry, hickory, oak, olive, plum, sugar maple), 4 softwood species (Douglas fir, pine, spruce, spruce/fir), treated softwood, beech and oak wood briquettes, paper briquettes, brown coal, wood chips, and herbaceous species (miscanthus, Chinese silver grass) as fuel. Particle composition (black carbon, non-refractory, and some semi-refractory species) was measured continuously. Repeatability was shown to be better for the pellet stove than for the wood stove. It was shown that the user has a strong influence on wood stove emission behavior both by selection of the fuel and of the burning conditions: Combustion efficiency was found to be low at both very low and very high burn rates, and influenced particle properties such as particle number, mass, and organic content in a complex way. No marked differences were found for the emissions from different wood species. For non-woody fuels, much higher emission factors could be observed (up to five-fold increase). Strongest enhancement of emission factors was found for burning of small or dried logs (up to six-fold), and usage of excess air (two- to three-fold). Real world pellet stove emissions can be expected to be much closer to laboratory-derived emission factors than wood stove emissions, due to lower dependence on user operation.

Decrease in sapling nutrient concentrations for six northern Rocky Mountain coniferous species

Treesearch

Theresa B. Jain; Russell T. Graham

2015-01-01

In the west, fire exclusion, timber harvest, and last century’s climate led to copious regeneration on millions of ha that now need tending. Without treatment, overcrowding increases competition, snow and ice damage potential, and ladder fuels. Limited funding prevents treating all of the affected ha, but by selling small trees for wood pellets, biofuel, or methanol,...

BrightFocus Foundation

MedlinePlus

... treatment for geographic atrophy, the advanced form of dry age-related macular degeneration. Thursday, September 28, 2017 ... and ICE Syndrome Iridocorneal endothelial syndrome, or ICE syndrome, is a ...

Meltlets(®) of soy isoflavones: process optimization and the effect of extrusion spheronization process parameters on antioxidant activity.

PubMed

Deshmukh, Ketkee; Amin, Purnima

2013-07-01

In the current research work an attempt was made to develop "Melt in mouth pellets" (Meltlets(®)) containing 40% herbal extract of soy isoflavones that served to provide antioxidants activity in menopausal women. The process of extrusion-spheronization was optimized for extruder speed, extruder screen size, spheronization speed, and time. While doing so the herbal extract incorporated in the pellet matrix was subjected to various processing conditions such as the effect of the presence of other excipients, mixing or kneading to prepare wet mass, heat generated during the process of extrusion, spheronization, and drying. Thus, the work further investigates the effect of these processing parameters on the antioxidant activity of the soy isoflavone herbal extract incorporated in the formula. Thereby, the antioxidant activity of the soya bean herbal extract, Meltlets(®) and of the placebo pellets was evaluated using DPPH free radical scavenging assay and total reduction capacity.

Modeling the effects of pelleting on the logistics of distillers grains shipping.

PubMed

Rosentrater, Kurt A; Kongar, Elif

2009-12-01

The energy security needs of energy importing nations continue to escalate. It is clear that biofuels can help meet some of the increasing need for energy. Theoretically, these can be produced from a variety of biological materials, including agricultural residues (such as corn stover and wheat straw), perennial grasses, legumes, algae, and other biological materials. Currently, however, the most heavily utilized material is corn starch. Industrial fuel ethanol production in the US primarily uses corn, because it is readily converted into fuel at a relatively low cost compared to other biomass sources. The production of corn-based ethanol in the US is dramatically increasing. As the industry continues to grow, the amount of byproducts and coproducts also increases. At the moment, the nonfermentable residues (which are dried and sold as distillers dried grains with solubles--DDGS) are utilized only as livestock feed. The sale of coproducts provides ethanol processors with a substantial revenue source and significantly increases the profitability of the production process. Even though these materials are used to feed animals in local markets, as the size and scope of the industry continues to grow, the need to ship large quantities of coproducts grows as well. This includes both domestic as well as international transportation. Value-added processing options offer the potential to increase the sustainability of each ethanol plant, and thus the industry overall. However, implementation of new technologies will be dependent upon how their costs interact with current processing costs and the logistics of coproduct deliveries. The objective of this study was to examine some of these issues by developing a computer model to determine potential cost ramifications of using various alternative technologies during ethanol processing. This paper focuses specifically on adding a densification unit operation (i.e., pelleting) to produce value-added DDGS at a fuel ethanol manufacturing plant. We have examined the economic implications of pelleting DDGS for varying DDGS production rates (100-1000 tons/d) and pelleting rates (0-100%), for a series of DDGS sales prices ($50-$200/ton). As the proportion of pelleting increases, the cost of transporting DDGS to distant markets drastically declines, because the rail cars can be filled to capacity. For example, at a DDGS sales price of $50/ton, 100% pelleting will reduce shipping costs (both direct and indirect) by 89% compared to shipping the DDGS in bulk form (i.e., no pelleting), whereas at a DDGS sales price of $200/ton, it will reduce costs by over 96%. It is clear that the sustainability of the ethanol industry can be improved by implementing pelleting technology for the coproducts, especially at those plants that ship their DDGS via rail.

Investigation of pharmaceutical drugs and caffeine-containing foods using Fourier and terahertz time-domain spectroscopy

NASA Astrophysics Data System (ADS)

KaraliÅ«nas, Mindaugas; Venckevičius, Rimvydas; Kašalynas, Irmantas; Puc, Uroš; Abina, Andreja; Jeglič, Anton; Zidanšek, Aleksander; Valušis, Gintaras

2015-08-01

Several pharmaceutical drugs, such as alprazolam, ibuprofen, acetaminophen, activated carbon and others, and caffeine-containing foods were tested using terahertz (THz) time domain spectroscopy in the range from 0.3 to 2 THz. The dry powder of pharmaceutical drugs was mixed with HDPE and pressed into the pellets using hydraulic press. The coffee grounds were also pressed into the pellets after ball-milling and mixing with HDPE. The caffeine containing liquid foods were dried out on the paper strips of various stacking. Experiments allow one to determine characteristic spectral signatures of the investigated substances within THz range caused by active pharmaceutical ingredients, like in the case of caffeine, as well as supporting pharmaceutical ingredients. Spectroscopic THz imaging approach is considered as a possible option to identify packaged pharmaceutical drugs. The caffeine spectral features in the tested caffeine containing foods are difficult to observed due to the low caffeine concentration and complex caffeine chemical surrounding.

Draft genome sequence of Paenisporosarcina sp. strain TG-14, a psychrophilic bacterium isolated from sediment-laden stratified basal ice from Taylor Glacier, McMurdo Dry Valleys, Antarctica.

PubMed

Koh, Hye Yeon; Lee, Sung Gu; Lee, Jun Hyuck; Doyle, Shawn; Christner, Brent C; Kim, Hak Jun

2012-12-01

The psychrophilic bacterium Paenisporosarcina sp. TG-14 was isolated from sediment-laden stratified basal ice from Taylor Glacier, McMurdo Dry Valleys, Antarctica. Here we report the draft genome sequence of this strain, which may provide useful information on the cold adaptation mechanism in extremely variable environments.

Small-Scale Production of High-Density Dry Ice: A Variant Combination of Two Classic Demonstrations

ERIC Educational Resources Information Center

Flowers, Paul A.

2009-01-01

Easily recoverable, thumb-sized pieces of high-density dry ice are conveniently produced by deposition of carbon dioxide within a test tube submerged in liquid nitrogen. A carbon dioxide-filled balloon sealed over the mouth of the test tube serves as a gas reservoir, and further permits a dramatic demonstration of both the gas-to-solid phase…

35 GHz Measurements of CO2 Crystals for Simulating Observations of the Martian Polar Caps

NASA Technical Reports Server (NTRS)

Foster, J. L.; Chang, A. T. C.; Hall, D. K.; Tait, A. B.; Barton, J. S.

1998-01-01

In order to learn more about the Martian polar caps, it is important to compare and contrast the behavior of both frozen H2O and CO2 in different parts of the electromagnetic spectrum. Relatively little attention has been given, thus far, to observing the thermal microwave part of the spectrum. In this experiment, passive microwave radiation emanating from within a 33 cm snowpack was measured with a 35 GHz hand-held radiometer, and in addition to the natural snow measurements, the radiometer was used to measure the microwave emission and scattering from layers of manufactured CO2 (dry ice). A 1 m x 2 m plate of aluminum sheet metal was positioned beneath the natural snow so that microwave emissions from the underlying soil layers would be minimized. Compared to the natural snow crystals, results for the dry ice layers exhibit lower' microwave brightness temperatures for similar thicknesses, regardless of the incidence angle of the radiometer. For example, at 50 degree H (horizontal polarization) and with a covering of 21 cm of snow and 18 cm of dry ice, the brightness temperatures were 150 K and 76 K, respectively. When the snow depth was 33 cm, the brightness temperature was 144 K, and when the total thickness of the dry ice was 27 cm, the brightness temperature was 86 K. The lower brightness temperatures are due to a combination of the lower physical temperature and the larger crystal sizes of the commercial CO2 Crystals compared to the snow crystals. As the crystal size approaches the size of the microwave wavelength, it scatters microwave radiation more effectively, thus lowering the brightness temperature. The dry ice crystals in this experiment were about an order of magnitude larger than the snow crystals and three orders of magnitude larger than the CO2 Crystals produced in the cold stage of a scanning electron microscope. Spreading soil, approximately 2 mm in thickness, on the dry ice appeared to have no effect on the brightness temperatures.

Thermomechanical Ablation

DTIC Science & Technology

1975-09-01

Ice, and Camphor (Summarized from Ref 11) . . . . . . . 16 3 Boundary Layer Edge Velocity Normalized by Free Stream Velocity for a Sphere and a...function of environmental conditions for water ice, dry ice, and camphor which are summarized in Figure 2. A low turbulence subsonic free jet was chosen

Visible and near-infrared reflectance spectroscopy of planetary analog materials. Experimental facility at Laboratoire de Planetologie de Grenoble.

NASA Astrophysics Data System (ADS)

Pommerol, A.; Brissaud, O.; Schmitt, B.; Quirico, E.; Doute, S.

2007-08-01

We have developed an original experimental facility designed to measure the bidirectional reflectance spectra of planetary analog materials. These measurements are helpful to interpret the observations of the spectrometers on board space probes in orbit around various Solar System bodies. The central part of the facility is the LPG spectrogonio- radiometer (Brissaud et al., 2004). This instrument provides measurements of samples BRDF (Bidirectional Reflectance Distribution Function) with high photometric and spectrometric accuracy in the spectral range of visible and near-infrared (0.3 - 4.8 microns). Measurements can be made at any value of incidence and emergence angle up to 80°. Azimuth angle is allowed to vary between 0 and 180°. The instrument was recently installed in a cold room allowing ambient temperatures as low as -20°C. This makes possible the measurements on different kinds of water ice samples (slab ice, frost, snow...) and mixtures of minerals and water ice with unprecedented accuracy. We also have designed and built a simulation chamber to measure spectra of samples (water ice and/or minerals) under an atmosphere with perfectly controlled temperature, pressure and composition. The main objective of this last improvement is the study of water exchange between planetary regolith analogs and atmosphere (adsorption/ desorption, condensation/sublimation). Experimental results will mainly apply to Martian water cycle and hydrated mineralogy. This simulation chamber also provides an efficient way to obtain bidirectional reflectance spectra of dry materials (removal of adsorbed water) with implications for planetary bodies without atmospheric or surface water (Titan, asteroids...). The reflectance spectroscopy facility is part of a large panel of instruments and techniques available at Laboratoire de Planetologie de Grenoble that provide complementary measurements on the same samples: infrared transmission spectroscopy of thin ice films, thick liquid and solid samples and samples diluted in KBr pellets, infrared imaging microscope, numerical modeling of bidirectional reflectance spectra using laboratory-measured optical constants. We will present different examples of experimental results obtained on the reflectance spectroscopy facility: - Effects of particle size, mixtures between samples with different albedo and measurement geometries on the water-of-hydration near-infrared absorption signatures with implications for the Martian regolith water content. - BRDF of regolith analogs and natural snow. - Hydration and dehydration of planetary analogs. - Spectra of different kinds of mixtures between water ice and minerals. We will briefly discuss the planetary implications of each of these measurements and detail the future investigations that will be undertaken on our experimental facility.

Heating the Ice-Covered Lakes of the McMurdo Dry Valleys, Antarctica - Decadal Trends in Heat Content, Ice Thickness, and Heat Exchange

NASA Astrophysics Data System (ADS)

Gooseff, M. N.; Priscu, J. C.; Doran, P. T.; Chiuchiolo, A.; Obryk, M.

2014-12-01

Lakes integrate landscape processes and climate conditions. Most of the permanently ice-covered lakes in the McMurdo Dry Valleys, Antarctica are closed basin, receiving glacial melt water from streams for 10-12 weeks per year. Lake levels rise during the austral summer are balanced by sublimation of ice covers (year-round) and evaporation of open water moats (summer only). Vertical profiles of water temperature have been measured in three lakes in Taylor Valley since 1988. Up to 2002, lake levels were dropping, ice covers were thickening, and total heat contents were decreasing. These lakes have been gaining heat since the mid-2000s, at rates as high as 19.5x1014 cal/decade). Since 2002, lake levels have risen substantially (as much as 2.5 m), and ice covers have thinned (1.5 m on average). Analyses of lake ice thickness, meteorological conditions, and stream water heat loads indicate that the main source of heat to these lakes is from latent heat released when ice-covers form during the winter. An aditional source of heat to the lakes is water inflows from streams and direct glacieal melt. Mean lake temperatures in the past few years have stabilized or cooled, despite increases in lake level and total heat content, suggesting increased direct inflow of meltwater from glaciers. These results indicate that McMurdo Dry Valley lakes are sensitive indicators of climate processes in this polar desert landscape and demonstrate the importance of long-term data sets when addressing the effects of climate on ecosystem processes.

Modeling and Simulation of Used Nuclear Fuel During Transportation with Consideration of Hydride Effects and Cyclic Fatigue

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chakraborty, Pritam; Sabharwall, Piyush; Spears, Robert Edward

2015-09-30

The objective of this work is to understand the integrity of Used Nuclear Fuel (UNF) during transportation. Previous analysis work has been performed to look at the integrity of UNF during transportation but these analyses have neglected to analyze the effect of hydrides and flaws (fracture mechanics models to capture radial cracking in the cladding). In this study, the clad regions of interest are near the pellet-pellet interfaces. These regions can experience more complex stress-states than the rest of the clad during cooling and have a greater possibility to develop radially reoriented hydrides during vacuum drying.

Hydrogeomorphic processes of thermokarst lakes with grounded-ice and floating-ice regimes on the Arctic coastal plain, Alaska

USGS Publications Warehouse

Arp, C.D.; Jones, Benjamin M.; Urban, F.E.; Grosse, G.

2011-01-01

Thermokarst lakes cover > 20% of the landscape throughout much of the Alaskan Arctic Coastal Plain (ACP) with shallow lakes freezing solid (grounded ice) and deeper lakes maintaining perennial liquid water (floating ice). Thus, lake depth relative to maximum ice thickness (1·5–2·0 m) represents an important threshold that impacts permafrost, aquatic habitat, and potentially geomorphic and hydrologic behaviour. We studied coupled hydrogeomorphic processes of 13 lakes representing a depth gradient across this threshold of maximum ice thickness by analysing remotely sensed, water quality, and climatic data over a 35-year period. Shoreline erosion rates due to permafrost degradation ranged from L) with periods of full and nearly dry basins. Shorter-term (2004–2008) specific conductance data indicated a drying pattern across lakes of all depths consistent with the long-term record for only shallow lakes. Our analysis suggests that grounded-ice lakes are ice-free on average 37 days longer than floating-ice lakes resulting in a longer period of evaporative loss and more frequent negative P − EL. These results suggest divergent hydrogeomorphic responses to a changing Arctic climate depending on the threshold created by water depth relative to maximum ice thickness in ACP lakes.

Cryostratigraphy and the Sublimation Unconformity in Permafrost from an Ultraxerous Environment, University Valley, McMurdo Dry Valleys of Antarctica

NASA Technical Reports Server (NTRS)

Lapalme, Caitlin M.; Fortier, Daniel; Pollard, Wayne; Lacelle, Denis; Davila, Alfonso; McKay, Christopher P.

2017-01-01

The cryostratigraphy of permafrost in ultraxerous environments is poorly known. In this study, icy permafrost cores from University Valley (McMurdo Dry Valleys, Antarctica) were analyzed for sediment properties, ground-ice content, types and distribution of cryostructures, and presence of unconformities. No active layer exists in the valley, but the ice table, a sublimation unconformity, ranges from 0 to 60 cm depth. The sediments are characterized as a medium sand, which classifies them as low to non-frost susceptible. Computed tomography (CT) scan images of the icy permafrost cores revealed composite cryostructures that included the structureless, porous visible, suspended and crustal types. These cryostructures were observed irrespective of ground-ice origin (vapour deposited and freezing of snow meltwater), suggesting that the type and distribution of cryostructures could not be used as a proxy to infer the mode of emplacement of ground ice. Volumetric ice content derived from the CT scan images underestimated measured volumetric ice content, but approached measured excess ice content. A palaeo-sublimation unconformity could not be detected from a change in cryostructures, but could be inferred from an increase in ice content at the maximum predicted ice table depth. This study highlights some of the unique ground-ice processes and cryostructures in ultraxerous environments.

Measured performance of the heat exchanger in the NASA icing research tunnel under severe icing and dry-air conditions

NASA Technical Reports Server (NTRS)

Olsen, W.; Vanfossen, J.; Nussle, R.

1987-01-01

Measurements were made of the pressure drop and thermal perfomance of the unique refrigeration heat exchanger in the NASA Lewis Icing Research Tunnel (IRT) under severe icing and frosting conditions and also with dry air. This data will be useful to those planning to use or extend the capability of the IRT and other icing facilities (e.g., the Altitude Wind Tunnel-AWT). The IRT heat exchanger and refrigeration system is able to cool air passing through the test section down to at least a total temperature of -30 C (well below icing requirements), and usually up to -2 C. The system maintains a uniform temperature across the test section at all airspeeds, which is more difficult and time consuming at low airspeeds, at high temperatures, and on hot, humid days when the cooling towers are less efficient. The very small surfaces of the heat exchanger prevent any icing cloud droplets from passing through it and going through the tests section again. The IRT heat exchanger was originally designed not to be adversely affected by severe icing. During a worst-case icing test the heat exchanger iced up enough so that the temperature uniformaity was no worse than about +/- 1 deg C. The conclusion is that the heat exchanger design performs well.

Disparities in Intratumoral Steroidogenesis

DTIC Science & Technology

2013-07-01

Tuesday shipment only) by overnight express for next day delivery on dry ice. Frozen specimens will be shipped on dry ice to the following address...Samples will be labeled with the study subject number and date of surgery. Frozen samples will be batch shipped (Monday and Tuesday shipment only) by... Morris MJ, de Bono JS, Ryan CJ, Denmeade SR, Smith MR, et al. Phase II multicenter study of abiraterone acetate plus prednisone therapy in patients

Effect of Controlled Ice Nucleation on Stability of Lactate Dehydrogenase During Freeze-Drying.

PubMed

Fang, Rui; Tanaka, Kazunari; Mudhivarthi, Vamsi; Bogner, Robin H; Pikal, Michael J

2018-03-01

Several controlled ice nucleation techniques have been developed to increase the efficiency of the freeze-drying process as well as to improve the quality of pharmaceutical products. Owing to the reduction in ice surface area, these techniques have the potential to reduce the degradation of proteins labile during freezing. The objective of this study was to evaluate the effect of ice nucleation temperature on the in-process stability of lactate dehydrogenase (LDH). LDH in potassium phosphate buffer was nucleated at -4°C, -8°C, and -12°C using ControLyo™ or allowed to nucleate spontaneously. Both the enzymatic activity and tetramer recovery after freeze-thawing linearly correlated with product ice nucleation temperature (n = 24). Controlled nucleation also significantly improved batch homogeneity as reflected by reduced inter-vial variation in activity and tetramer recovery. With the correlation established in the laboratory, the degradation of protein in manufacturing arising from ice nucleation temperature differences can be quantitatively predicted. The results show that controlled nucleation reduced the degradation of LDH during the freezing process, but this does not necessarily translate to vastly superior stability during the entire freeze-drying process. The capability of improving batch homogeneity provides potential advantages in scaling-up from lab to manufacturing scale. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

The Novel Approach to Enhance Seed Security: Dual Anti-Counterfeiting Methods Applied on Tobacco Pelleted Seeds

PubMed Central

Guan, Yajing; Wang, Jianchen; Tian, Yixin; Hu, Weimin; Zhu, Liwei; Zhu, Shuijin; Hu, Jin

2013-01-01

Seed security is of prime importance for agriculture. To protect true seeds from being faked, more secure dual anti-counterfeiting technologies for tobacco (Nicotiana tabacum L.) pelleted seed were developed in this paper. Fluorescein (FR), rhodamine B (RB), and magnetic powder (MP) were used as anti-counterfeiting labels. According to their different properties and the special seed pelleting process, four dual-labeling treatments were conducted for two tobacco varieties, MS Yunyan85 (MSYY85) and Honghua Dajinyuan (HHDJY). Then the seed germination and seedling growth status were investigated, and the fluorescence in cracked pellets and developing seedlings was observed under different excitation lights. The results showed that FR, RB, and MP had no negative effects on the germination, seedling growth, and MDA content of the pelleted seeds, and even some treatments significantly enhanced seedling dry weight, vigor index, and shoot height in MS YY85, and increased SOD activity and chlorophyll content in HHDJY as compared to the control. In addition, the cotyledon tip of seedlings treated with FR and MP together represented bright green fluorescence under illumination of blue light (478 nm). And the seedling cotyledon vein treated with RB and MP together showed red fluorescence under green light (546 nm). All seeds pelleted with magnetic powder of proper concentration could be attracted by a magnet. Thus, it indicated that those new dual-labeling methods that fluorescent compound and magnetic powder simultaneously applied in the same seed pellets definitely improved anti-counterfeiting technology and enhanced the seed security. This technology will ensure that high quality seed will be used in the crop production. PMID:23468953

Manufacturing Solid Dosage Forms from Bulk Liquids Using the Fluid-bed Drying Technology.

PubMed

Qi, Jianping; Lu, Y I; Wu, Wei

2015-01-01

Solid dosage forms are better than liquid dosage forms in many ways, such as improved physical and chemical stability, ease of storage and transportation, improved handling properties, and patient compliance. Therefore, it is required to transform dosage forms of liquid origins into solid dosage forms. The functional approaches are to absorb the liquids by solid excipients or through drying. The conventional drying technologies for this purpose include drying by heating, vacuum-, freeze- and spray-drying, etc. Among these drying technologies, fluidbed drying emerges as a new technology that possesses unique advantages. Fluid-bed drying or coating is highly efficient in solvent removal, can be performed at relatively low temperatures, and is a one-step process to manufacture formulations in pellet forms. In this article, the status of the art of manufacturing solid dosage forms from bulk liquids by fluid-bed drying technology was reviewed emphasizing on its application in solid dispersion, inclusion complexes, self-microemulsifying systems, and various nanoscale drug delivery systems.

Spatial Heterogeneity of Ice Cover Sediment and Thickness and Its Effects on Photosynthetically Active Radiation and Chlorophyll-a Distribution: Lake Bonney, Antarctica

NASA Astrophysics Data System (ADS)

Obryk, M.; Doran, P. T.; Priscu, J. C.; Morgan-Kiss, R. M.; Siebenaler, A. G.

2012-12-01

The perennially ice-covered lakes in the McMurdo Dry Valleys, Antarctica have been extensively studied under the Long Term Ecological Research project. But sampling has been spatially restricted due to the logistical difficulty of penetrating the 3-6 m of ice cover. The ice covers restrict wind-driven turbulence and its associated mixing of water, resulting in a unique thermal stratification and a strong vertical gradient of salinity. The permanent ice covers also shade the underlying water column, which, in turn, controls photosynthesis. Here, we present results of a three-dimensional record of lake processes obtained with an autonomous underwater vehicle (AUV). The AUV was deployed at West Lake Bonney, located in Taylor Valley, Dry Valleys, to further understand biogeochemical and physical properties of the Dry Valley lakes. The AUV was equipped with depth, conductivity, temperature, under water photosynthetically active radiation (PAR), turbidity, chlorophyll-and-DOM fluorescence, pH, and REDOX sensors. Measurements were taken over the course of two years in a 100 x 100 meter spaced horizontal sampling grid (and 0.2 m vertical resolution). In addition, the AUV measured ice thickness and collected 200 images looking up through the ice, which were used to quantify sediment distribution. Comparison with high-resolution satellite QuickBird imagery demonstrates a strong correlation between aerial sediment distribution and ice cover thickness. Our results are the first to show the spatial heterogeneity of lacustrine ecosystems in the McMurdo Dry Valleys, significantly improving our understanding of lake processes. Surface sediment is responsible for localized thinning of ice cover due to absorption of solar radiation, which in turn increases total available PAR in the water column. Higher PAR values are negatively correlated with chlorophyll-a, presenting a paradox; historically, long-term studies of PAR and chlorophyll-a have shown positive trends. We hypothesized that this paradox is a result of short-term photoadaptation of phytoplanktonic communities to spatial and temporal variations of PAR within the water column. To test this hypothesis, we established phytoplankton enrichment cultures from depths of maximum primary production (13 m) and tested whether dry valley lake phytoplankton respond to daily variations in controlled light environment. Laboratory-grown cultures exhibited a strong response at 12 hr:12 hr day:night cycle at the level of both photochemistry and chlorophyll biosynthesis, indicating that Lake Bonney possess the ability to quickly respond to changes in their light environment.

Ground penetrating radar detection of subsnow slush on ice-covered lakes in interior Alaska

NASA Astrophysics Data System (ADS)

Gusmeroli, A.; Grosse, G.

2012-12-01

Lakes are abundant throughout the pan-Arctic region. For many of these lakes ice cover lasts for up to two thirds of the year. The frozen cover allows human access to these lakes, which are therefore used for many subsistence and recreational activities, including water harvesting, fishing, and skiing. Safe traveling condition onto lakes may be compromised, however, when, after significant snowfall, the weight of the snow acts on the ice and causes liquid water to spill through weak spots and overflow at the snow-ice interface. Since visual detection of subsnow slush is almost impossible our understanding on overflow processes is still very limited and geophysical methods that allow water and slush detection are desirable. In this study we demonstrate that a commercially available, lightweight 1 GHz, ground penetrating radar system can detect and map extent and intensity of overflow. The strength of radar reflections from wet snow-ice interfaces are at least twice as much in strength than returns from dry snow-ice interface. The presence of overflow also affects the quality of radar returns from the base of the lake ice. During dry conditions we were able to profile ice thickness of up to 1 m, conversely, we did not retrieve any ice-water returns in areas affected by overflow.

Perennially ice-covered Lake Hoare, Antarctica: physical environment, biology and sedimentation

NASA Technical Reports Server (NTRS)

Wharton, R. A. Jr; Simmons, G. M. Jr; McKay, C. P.; Wharton RA, J. r. (Principal Investigator)

1989-01-01

Lake Hoare (77 degrees 38' S, 162 degrees 53' E) is a perennially ice-covered lake at the eastern end of Taylor Valley in southern Victoria Land, Antarctica. The environment of this lake is controlled by the relatively thick ice cover (3-5 m) which eliminates wind generated currents, restricts gas exchange and sediment deposition, and reduces light penetration. The ice cover is in turn largely controlled by the extreme seasonality of Antarctica and local climate. Lake Hoare and other dry valley lakes may be sensitive indicators of short term (< 100 yr) climatic and/or anthropogenic changes in the dry valleys since the onset of intensive exploration over 30 years ago. The time constants for turnover of the water column and lake ice are 50 and 10 years, respectively. The turnover time for atmospheric gases in the lake is 30-60 years. Therefore, the lake environment responds to changes on a 10-100 year timescale. Because the ice cover has a controlling influence on the lake (e.g. light penetration, gas content of water, and sediment deposition), it is probable that small changes in ice ablation, sediment loading on the ice cover, or glacial meltwater (or groundwater) inflow will affect ice cover dynamics and will have a major impact on the lake environment and biota.

Evaluation of the viability of Lactobacillus spp. after the production of different solid dosage forms.

PubMed

Brachkova, Mariya I; Duarte, Aida; Pinto, João F

2009-09-01

The work aims to provide evidence on the viability of Lactobacillus spp. and a spore form of Bacillus subtilis from nonprocessed bacteria to coated dosage forms (i.e., mini-tablets, pellets, and their coated forms). Lactobacillus spp. were cultivated overnight in MRS broth (10(9) cfu/mL) and B. subtilis spores were produced on plate count agar (10(7) cfu/mL) for 2 weeks. Bacteria and spores were freeze-dried in skim milk enriched with glycerol. The cakes were further processed into tablets (2.5 mm diameter) by direct compression with or without microcrystalline cellulose and inulin. Pellets (1-1.4 mm diameter) were produced by extrusion-spheronization of bacterial and spore suspensions with microcrystalline cellulose, lactose, inulin, and skim milk. Both tablets and pellets were film coated. The properties of the dosage forms, particularly the bacterial viability, were evaluated immediately after production and throughout storage for 6 months at 4 degrees C. The study has shown that for an adequate stabilization of the bacteria a protective matrix (e.g., skim milk) and cryoprotectors (e.g., glycerol) must be present at early stages of bacterial de-hydration. Tabletting had a less deleterious effect (<2 log units) on bacteria when compared to pelletization (in some cases 3 log units). Enteric coating (15%, w/w) of either tablets or pellets did not affect the viability of the bacteria.

Overcoming the challenges of mosquito (Diptera: Culicidae) sampling in remote localities: a comparison of CO2 attractants on mosquito communities in three tropical forest habitats.

PubMed

Steiger, D B Meyer; Ritchie, S A; Laurance, S G W

2014-01-01

Emerging infectious diseases are on the rise with future outbreaks predicted to occur in frontier regions of tropical countries. Disease surveillance in these hotspots is challenging because sampling techniques often rely on vector attractants that are either unavailable in remote localities or difficult to transport. We examined whether a novel method for producing CO2 from yeast and sugar produces similar mosquito species captures compared with a standard attractant such as dry ice. Across three different vegetation communities, we found traps baited with dry ice frequently captured more mosquitoes than yeast-baited traps; however, there was little effect on mosquito community composition. Based on our preliminary experiments, we find that this method of producing CO2 is a realistic alternative to dry ice and would be highly suitable for remote field work.

The Coolest Landscape on Mars or Earth

NASA Image and Video Library

2016-12-07

Many Martian landscapes contain features that are familiar to ones we find on Earth, like river valleys, cliffs, glaciers and volcanos. However, Mars has an exotic side too, with landscapes that are alien to Earthlings. This image shows one of these exotic locales at the South Pole. The polar cap is made from carbon dioxide (dry ice), which does not occur naturally on the Earth. The circular pits are holes in this dry ice layer that expand by a few meters each Martian year. New dry ice is constantly being added to this landscape by freezing directly out of the carbon dioxide atmosphere or falling as snow. Freezing out the atmosphere like this limits how cold the surface can get to the frost point at -130 degrees Celsius (-200 F). Nowhere on Mars can ever get any colder this, making this this coolest landscape on Earth and Mars combined. http://photojournal.jpl.nasa.gov/catalog/PIA21216

Plants as sources of airborne bacteria, including ice nucleation-active bacteria.

PubMed

Lindemann, J; Constantinidou, H A; Barchet, W R; Upper, C D

1982-11-01

Vertical wind shear and concentration gradients of viable, airborne bacteria were used to calculate the upward flux of viable cells above bare soil and canopies of several crops. Concentrations at soil or canopy height varied from 46 colony-forming units per m over young corn and wet soil to 663 colony-forming units per m over dry soil and 6,500 colony-forming units per m over a closed wheat canopy. In simultaneous samples, concentrations of viable bacteria in the air 10 m inside an alfalfa field were fourfold higher than those over a field with dry, bare soil immediately upwind. The upward flux of viable bacteria over alfalfa was three- to fourfold greater than over dry soil. Concentrations of ice nucleation-active bacteria were higher over plants than over soil. Thus, plant canopies may constitute a major source of bacteria, including ice nucleation-active bacteria, in the air.

Dry Ice Etches Terrain

NASA Technical Reports Server (NTRS)

2007-01-01

[figure removed for brevity, see original site] Figure 1

Every year seasonal carbon dioxide ice, known to us as 'dry ice,' covers the poles of Mars. In the south polar region this ice is translucent, allowing sunlight to pass through and warm the surface below. The ice then sublimes (evaporates) from the bottom of the ice layer, and carves channels in the surface.

The channels take on many forms. In the subimage shown here (figure 1) the gas from the dry ice has etched wide shallow channels. This region is relatively flat, which may be the reason these channels have a different morphology than the 'spiders' seen in more hummocky terrain.

Observation Geometry Image PSP_003364_0945 was taken by the High Resolution Imaging Science Experiment (HiRISE) camera onboard the Mars Reconnaissance Orbiter spacecraft on 15-Apr-2007. The complete image is centered at -85.4 degrees latitude, 104.0 degrees East longitude. The range to the target site was 251.5 km (157.2 miles). At this distance the image scale is 25.2 cm/pixel (with 1 x 1 binning) so objects 75 cm across are resolved. The image shown here has been map-projected to 25 cm/pixel . The image was taken at a local Mars time of 06:57 PM and the scene is illuminated from the west with a solar incidence angle of 75 degrees, thus the sun was about 15 degrees above the horizon. At a solar longitude of 219.6 degrees, the season on Mars is Northern Autumn.

Simple Cloud Chambers Using a Freezing Mixture of Ice and Cooking Salt

ERIC Educational Resources Information Center

Yoshinaga, Kyohei; Kubota, Miki; Kamata, Masahiro

2015-01-01

We have developed much simpler cloud chambers that use only ice and cooking salt instead of the dry ice or ice gel pack needed for the cloud chambers produced in our previous work. The observed alpha-ray particle tracks are as clear as those observed using our previous cloud chambers. The tracks can be observed continuously for about 20?min, and…

Interaction of extender composition and freezing method for effective semen cryopreservation in the North American river otter (Lontra canadensis).

PubMed

Bateman, Helen L; Swanson, William F

2017-10-01

Semen cryopreservation and storage in genome resource banks (GRBs), in combination with artificial insemination (AI), could be invaluable for genetic management and conservation of endangered otter species. For any applied conservation benefit, effective methods for otter sperm processing and cryopreservation first must be established. In this study, our objective was to develop an effective semen cryopreservation method for the North American river otter, evaluating the effect of extender composition (i.e., glycerol concentration, Equex STM paste supplementation) and freezing protocol (timing of glycerol addition, pre-freeze cooling rate, freezing/packaging method) on post-thaw sperm motility, longevity and acrosome status. Semen was collected from 14 otters housed at 9 zoos, and following cryopreservation in an egg-yolk based extender, thawed to assess sperm motility and acrosome status immediately post-thaw and during 6 h of in vitro culture. Results indicated that extender containing 4% glycerol was preferable (p < 0.05) to 8% glycerol but the temperature/timing of extender addition containing 4% glycerol did not affect (p > 0.05) post-thaw sperm parameters. Treatments with extender containing Equex and frozen by pelleting on dry ice showed greater (p < 0.05) motility and percentage of intact acrosomes compared to treatments frozen in extender without Equex, regardless of pre-freeze cooling rate. In the absence of Equex, pelleting provided superior post-thaw sperm motility (p < 0.01) and higher (p < 0.001) percentage of sperm with intact acrosomes compared to samples frozen in straws over liquid nitrogen vapor. Results of this study indicate that cryopreservation of otter sperm using an egg-yolk -TEST based extender containing 4% glycerol and 1% Equex, with the pellet freezing method, provided superior post-thaw sperm motility, longevity and acrosomal integrity compared to other combinations. Neither alterations in timing of glycerolated extender addition nor pre-freeze cooling rate had a discernable effect on post-thaw otter sperm parameters. These findings represent the first assessment of semen cryopreservation in any otter species and may be of value as a model for development of semen cryopreservation strategies in other endangered otter species. Copyright © 2017 Elsevier Inc. All rights reserved.

Optimal Electromagnetic (EM) Geophysical Techniques to Map the Concentration of Subsurface Ice and Adsorbed Water on Mars and the Moon

NASA Astrophysics Data System (ADS)

Stillman, D. E.; Grimm, R. E.

2013-12-01

Water ice is ubiquitous in our Solar System and is a probable target for planetary exploration. Mapping the lateral and vertical concentration of subsurface ice from or near the surface could determine the origin of lunar and martian ice and quantify a much-needed resource for human exploration. Determining subsurface ice concentration on Earth is not trivial and has been attempted previously with electrical resistivity tomography (ERT), ground penetrating radar (GPR), airborne EM (AEM), and nuclear magnetic resonance (NMR). These EM geophysical techniques do not actually detect ice, but rather the absence of unfrozen water. This causes a non-unique interpretation of frozen and dry subsurface sediments. This works well in the arctic because most locations are not dry. However, for planetary exploration, liquid water is exceedingly rare and subsurface mapping must discriminate between an ice-rich and a dry subsurface. Luckily, nature has provided a unique electrical signature of ice: its dielectric relaxation. The dielectric relaxation of ice creates a temperature and frequency dependence of the electrical properties and varies the relative dielectric permittivity from ~3.1 at radar frequencies to >100 at low frequencies. On Mars, sediments smaller than silt size can hold enough adsorbed unfrozen water to complicate the measurement. This is because the presence of absorbed water also creates frequency-dependent electrical properties. The dielectric relaxation of adsorbed water and ice can be separated as they have different shapes and frequency ranges as long as a spectrum spanning the two relaxations is measured. The volume concentration of ice and adsorbed water is a function of the strength of their relaxations. Therefore, we suggest that capacitively-coupled dielectric spectroscopy (a.k.a. spectral induced polarization or complex resistivity) can detect the concentration of both ice and adsorbed water in the subsurface. To prove this concept we have collected dielectric spectroscopy at the Cold Regions Research and Engineering Laboratory (CRREL) permafrost tunnel in Fox, AK. We were able to detect the ice relaxation in the subsurface despite the considerable amount of subsurface unfrozen water due to the presence of montmorillonite clay and much warmer temperatures than Mars or permanently shadowed regions of the Moon. While dielectric spectroscopy can be used to determine ice and adsorbed water content it does not possess the high resolution mapping capability of a GPR. Moreover, GPR cannot detect subsurface ice content in ice-sediment mixtures as evidenced in the interpretation of the Medusae Fossae Formation. Orbital radar surveys show this unit has a low attenuation and a dielectric permittivity near 4. This allows the formation to be interpreted as ice-rich or a dry high-porosity volcanic tuff unit. Therefore, combining GPR and dielectric spectroscopy will enable high-resolution structural and volatile mapping of the subsurface. Furthermore, the addition of neutron spectroscopy would add total hydrogen abundance in the top meter. This could lead to the determination of how much hydrogen resides in ice, adsorbed water, and minerals.

Single sample extraction and HPLC processing for quantification of NAD and NADH levels in Saccharomyces cerevisiae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sporty, J; Kabir, M M; Turteltaub, K

A robust redox extraction protocol for quantitative and reproducible metabolite isolation and recovery has been developed for simultaneous measurement of nicotinamide adenine dinucleotide (NAD) and its reduced form, NADH, from Saccharomyces cerevisiae. Following culture in liquid media, approximately 10{sup 8} yeast cells were harvested by centrifugation and then lysed under non-oxidizing conditions by bead blasting in ice-cold, nitrogen-saturated 50-mM ammonium acetate. To enable protein denaturation, ice cold nitrogen-saturated CH{sub 3}CN + 50-mM ammonium acetate (3:1; v:v) was added to the cell lysates. After sample centrifugation to pellet precipitated proteins, organic solvent removal was performed on supernatants by chloroform extraction. Themore » remaining aqueous phase was dried and resuspended in 50-mM ammonium acetate. NAD and NADH were separated by HPLC and quantified using UV-VIS absorbance detection. Applicability of this procedure for quantifying NAD and NADH levels was evaluated by culturing yeast under normal (2% glucose) and calorie restricted (0.5% glucose) conditions. NAD and NADH contents are similar to previously reported levels in yeast obtained using enzymatic assays performed separately on acid (for NAD) and alkali (for NADH) extracts. Results demonstrate that it is possible to perform a single preparation to reliably and robustly quantitate both NAD and NADH contents in the same sample. Robustness of the protocol suggests it will be (1) applicable to quantification of these metabolites in mammalian and bacterial cell cultures; and (2) amenable to isotope labeling strategies to determine the relative contribution of specific metabolic pathways to total NAD and NADH levels in cell cultures.« less

Effects of pelleting, extrusion, or extrusion and pelleting on energy and nutrient digestibility in diets containing different levels of fiber and fed to growing pigs.

PubMed

Rojas, O J; Vinyeta, E; Stein, H H

2016-05-01

An experiment was conducted to determine effects of pelleting, extrusion, and extrusion and pelleting on energy and nutrient digestibility in diets containing low, medium, or high concentrations of fiber. Three diets were formulated: 1) the low-fiber diet contained corn and soybean meal; 2) the medium-fiber diet contained corn, soybean meal, and 25% distillers dried grains with solubles (DDGS); and 3) the high-fiber diet contained corn, soybean meal, 25% DDGS, and 20% soybean hulls. Each diet was divided into 4 batches after mixing. One batch was not further processed and was fed in a meal form, one batch was pelleted at 85°C, one batch was extruded at 115°C using a single-screw extruder, and one batch was extruded at 115°C and then pelleted at 85°C. Thus, 12 different diets were produced. Twenty-four growing pigs (26.5 ± 1.5 kg initial BW) had a T-cannula installed in the distal ileum and were allotted to the 12 diets in a split-plot design with 8 pigs allotted to the low-fiber diets, the medium-fiber diets, and the high-fiber diets, respectively. Diets were fed to the pigs during four 14-d periods. Within each type of diet, the 8 pigs were fed the diets produced using the 4 processing technologies. Therefore, there were 8 replicate pigs per diet. Pigs were adjusted to their diets for 14 d before the experiment was initiated. Each of the four 14-d periods consisted of 5 d for adaptation, 5 d of fecal collection according to the marker to marker approach, and ileal digesta were collected on d 13 and 14. Results indicated that pelleting, extrusion, or extrusion and pelleting improved ( < 0.05) the apparent ileal digestibility of starch and most indispensable AA. In most cases, there were no differences between the pelleted, the extruded, and the extruded and pelleted diets. The apparent total tract digestibility of GE was also improved ( < 0.05) by pelleting and by the combination of extrusion and pelleting. The ME of pelleted diets was greater ( < 0.05) than that of meal diets for the low- and medium-fiber diets, but this was not the case for high-fiber diets (interaction, < 0.05). Medium- and high-fiber diets that were extruded had greater ME ( < 0.05) than meal diets, but that was not the case for low-fiber diets. These data indicate that energy utilization may be improved by pelleting or extrusion or by a combination of the 2 technologies, but the response seems to be greater for extrusion in diets that are relatively high in fiber.

Efficacy of osmoprotectants on prevention and treatment of murine dry eye.

PubMed

Chen, Wei; Zhang, Xin; Li, Jinyang; Wang, Yu; Chen, Qi; Hou, Chao; Garrett, Qian

2013-09-19

To evaluate the efficacy of osmoprotectants on prevention and treatment of dry eye in a murine model. Dry eye was induced in mice by using an intelligently controlled environmental system (ICES). Osmoprotectants betaine, L-carnitine, erythritol, or vehicle (PBS) were topically administered to eyes four times daily following two schedules: schedule 1 (modeling prevention): dosing started at the beginning of housing in ICES and lasted for 21 or 35 days; schedule 2 (modeling treatment): dosing started after ICES-housed mice developed dry eye (day 21), continuing until day 35. Treatment efficacy was evaluated for corneal fluorescein staining; corneal epithelial apoptosis by TUNEL and caspase-3 assays; goblet cell numbers by PAS staining; and expression of inflammatory mediators, TNF-α, IL-17, IL-6, or IL-1β by using RT-PCR on days 0, 14, 21, and/or 35. Compared with vehicle, prophylactic administration of betaine, L-carnitine, or erythritol significantly decreased corneal staining and expression of TNF-α and IL-17 on day 21 (schedule 1). Treatment of mouse dry eye with osmoprotectants significantly reduced corneal staining on day 35 compared with day 21 (schedule 2). Relative to vehicle, L-carnitine treatment of mouse dry eye for 14 days (days 21 to 35) resulted in a significant reduction in corneal staining, number of TUNEL-positive cells, and expression of TNF-α, IL-17, IL-6, or IL-1β, as well as significantly increased the number of goblet cells. Topical application of betaine, L-carnitine, or erythritol systematically limited progression of environmentally induced dry eye. L-carnitine can also reduce the severity of such dry-eye conditions.

Heat transfer and pressure drop performance of a finned-tube heat exchanger proposed for use in the NASA Lewis Altitude Wind Tunnel

NASA Technical Reports Server (NTRS)

Vanfossen, G. J.

1985-01-01

A segment of the heat exchanger proposed for use in the NASA Lewis Altitude Wind Tunnel (AWT) facility has been tested under dry and icing conditions. The heat exchanger has the largest pressure drop of any component in the AWT loop. It is therefore critical that its performance be known at all conditions before the final design of the AWT is complete. The heat exchanger segment is tested in the NASA Lewis Icing Research Tunnel (IRT) in order to provide an icing cloud environment similar to what will be encountered in the AWT. Dry heat transfer and pressure drop data are obtained and compared to correlations available in the literature. The effects of icing sprays on heat transfer and pressure drop are also investigated.

Simple Cloud Chambers Using Gel Ice Packs

ERIC Educational Resources Information Center

Kamata, Masahiro; Kubota, Miki

2012-01-01

Although cloud chambers are highly regarded as teaching aids for radiation education, school teachers have difficulty in using cloud chambers because they have to prepare dry ice or liquid nitrogen before the experiment. We developed a very simple and inexpensive cloud chamber that uses the contents of gel ice packs which can substitute for dry…

The effects of snow and salt on ice table stability in University Valley, Antarctica

USGS Publications Warehouse

Williams, Kaj; Heldmann, Jennifer L.; McKay, Christopher P.; Mellon, Michael T.

2018-01-01

The Antarctic Dry Valleys represent a unique environment where it is possible to study dry permafrost overlaying an ice-rich permafrost. In this paper, two opposing mechanisms for ice table stability in University Valley are addressed: i) diffusive recharge via thin seasonal snow deposits and ii) desiccation via salt deposits in the upper soil column. A high-resolution time-marching soil and snow model was constructed and applied to University Valley, driven by meteorological station atmospheric measurements. It was found that periodic thin surficial snow deposits (observed in University Valley) are capable of drastically slowing (if not completely eliminating) the underlying ice table ablation. The effects of NaCl, CaCl2 and perchlorate deposits were then modelled. Unlike the snow cover, however, the presence of salt in the soil surface (but no periodic snow) results in a slight increase in the ice table recession rate, due to the hygroscopic effects of salt sequestering vapour from the ice table below. Near-surface pore ice frequently forms when large amounts of salt are present in the soil due to the suppression of the saturation vapour pressure. Implications for Mars high latitudes are discussed.

Evaluation of a Novel Artificial Tear in the Prevention and Treatment of Dry Eye in an Animal Model.

PubMed

She, Yujing; Li, Jinyang; Xiao, Bing; Lu, Huihui; Liu, Haixia; Simmons, Peter A; Vehige, Joseph G; Chen, Wei

2015-11-01

To evaluate effects of a novel multi-ingredient artificial tear formulation containing carboxymethylcellulose (CMC) and hyaluronic acid (HA) in a murine dry eye model. Dry eye was induced in mice (C57BL/6) using an intelligently controlled environmental system (ICES). CMC+HA (Optive Fusion™), CMC-only (Refresh Tears(®)), and HA-only (Hycosan(®)) artificial tears and control phosphate-buffered saline (PBS) were administered 4 times daily and compared with no treatment (n = 64 eyes per group). During regimen 1 (prevention regimen), mice were administered artificial tears or PBS for 14 days (starting day 0) while they were exposed to ICES, and assessed on days 0 and 14. During regimen 2 (treatment regimen), mice exposed to ICES for 14 days with no intervention were administered artificial tears or PBS for 14 days (starting day 14) while continuing exposure to ICES, and assessed on days 0, 14, and 28. Corneal fluorescein staining and conjunctival goblet cell density were measured. Artificial tear-treated mice had significantly better outcomes than control groups on corneal staining and goblet cell density (P < 0.01). Mice administered CMC+HA also showed significantly lower corneal fluorescein staining and higher goblet cell density, compared with CMC (P < 0.01) and HA (P < 0.05) in both regimens 1 and 2. The artificial tear formulation containing CMC and HA was effective in preventing and treating environmentally induced dry eye. Improvements observed for corneal fluorescein staining and conjunctival goblet cell retention suggest that this combination may be a viable treatment option for dry eye disease.

Cold tolerance of Littorinidae from southern Africa: intertidal snails are not constrained to freeze tolerance.

PubMed

Sinclair, Brent J; Marshall, David J; Singh, Sarika; Chown, Steven L

2004-11-01

All intertidal gastropods for which cold tolerance strategies have been assessed have been shown to be freeze tolerant. Thus, freeze tolerance is considered an adaptation to the intertidal environment. We investigated the cold tolerance strategies of three species of subtropical and temperate snails (Gastropoda: Littorinidae) to determine whether this group is phylogenetically constrained to freeze tolerance. We exposed 'dry' acclimated and 'wet' rehydrated snails to low temperatures to determine temperature of crystallisation (Tc), lower lethal temperature and LT(50) and to examine the relationship between ice formation and mortality. Tc was lowest in dry Afrolittorina knysnaensis (-13.6+/-0.4 degrees C), followed by dry Echinolittorina natalensis (-10.9+/-0.2 degrees C) and wet A. knysnaensis (-10.2+/-0.2 degrees C) . The Tc of both A. knysnaensis and E. natalensis increased with rehydration, whereas Tc of dry and wet Afrolittorina africana did not differ (-9.6+/-0.2 and -9.0+/-0.2 degrees C respectively). Wet snails of all species exhibited no or low survival of inoculative freezing, whereas dry individuals of A. knysnaensis could survive subzero temperatures above -8 degrees C when freezing was inoculated with ice . In the absence of external ice, Afrolittorina knysnaensis employs a freeze-avoidance strategy of cold tolerance, the first time this has been reported for an intertidal snail, indicating that there is no family-level phylogenetic constraint to freeze tolerance. Echinolittorina natalensis and A. africana both showed pre-freeze mortality and survival of some internal ice formation, but were not cold hardy in any strict sense.

New particle dependant parameterizations of heterogeneous freezing processes.

NASA Astrophysics Data System (ADS)

Diehl, Karoline; Mitra, Subir K.

2014-05-01

For detailed investigations of cloud microphysical processes an adiabatic air parcel model with entrainment is used. It represents a spectral bin model which explicitly solves the microphysical equations. The initiation of the ice phase is parameterized and describes the effects of different types of ice nuclei (mineral dust, soot, biological particles) in immersion, contact, and deposition modes. As part of the research group INUIT (Ice Nuclei research UnIT), existing parameterizations have been modified for the present studies and new parameterizations have been developed mainly on the basis of the outcome of INUIT experiments. Deposition freezing in the model is dependant on the presence of dry particles and on ice supersaturation. The description of contact freezing combines the collision kernel of dry particles with the fraction of frozen drops as function of temperature and particle size. A new parameterization of immersion freezing has been coupled to the mass of insoluble particles contained in the drops using measured numbers of ice active sites per unit mass. Sensitivity studies have been performed with a convective temperature and dew point profile and with two dry aerosol particle number size distributions. Single and coupled freezing processes are studied with different types of ice nuclei (e.g., bacteria, illite, kaolinite, feldspar). The strength of convection is varied so that the simulated cloud reaches different levels of temperature. As a parameter to evaluate the results the ice water fraction is selected which is defined as the relation of the ice water content to the total water content. Ice water fractions between 0.1 and 0.9 represent mixed-phase clouds, larger than 0.9 ice clouds. The results indicate the sensitive parameters for the formation of mixed-phase and ice clouds are: 1. broad particle number size distribution with high number of small particles, 2. temperatures below -25°C, 3. specific mineral dust particles as ice nuclei such as illite or montmorillonite. Coupled cases of deposition and contact freezing show that they are hardly in competition because of differences in the preferred particle sizes. In the contact mode, small particles are less efficient for collisions as well as less efficient as ice nuclei so that these are available for deposition freezing. On the other hand, immersion freezing is the dominant process when it is coupled with deposition freezing. As it is initiated earlier the formed ice particles consume water vapor for growing. The competition of combined contact and immersion freezing leads to lower ice water contents because more ice particles are formed via the immersion mode. In general, ice clouds and mixed-phase clouds with high ice water fractions are not directly the result of primary ice formation but of secondary ice formation and growth of ice particles at the expense of liquid drops.

Development of a two-stage light gas gun to accelerate hydrogen pellets to high speeds for plasma fueling applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Combs, S.K.; Milora, S.L.; Foust, C.R.

1989-05-01

The development of a two-stage light gas gun to accelerate hydrogen isotope pellets to high speeds is under way at Oak Ridge National Laboratory. High velocities (>2 km/s) are desirable for plasma fueling applications, since the faster pellets can penetrate more deeply into large, hot plasmas and deposit atoms of fuel directly in a larger fraction of the plasma volume. In the initial configuration of the two-stage device, a 2.2-1 volume (less than or equal to55 bar) provides the gas to accelerate a 25.4-mm-diam piston in a 1-m-long pump tube; a burst disk or a fast valve initiates the accelerationmore » process in the first stage. As the piston travels the length of the pump tube, the downstream gas (initially at <1 bar) is compressed (to pressures up to 2600 bar) and thus is driven to high temperature (approx. =5000 K). This provides the driving force for acceleration of a 4-mm pellet in a 1-m-long gun barrel. In preliminary tests using helium as the driver in both stages, 35-mg plastic pellets have been accelerated to speeds as high as 4.0 km/s. Projectiles composed of hydrogen ice will have a mass in the range from 5 to 20 mg ( rhoapprox. =0.087, 0.20, and 0.32 g/cm/sup 3/ for frozen hydrogen isotopes). However, the use of sabots to encase and protect the cryogenic pellets from the high peak pressures will probably be required to realize speeds of approx. =3 km/s or greater. The experimental plan includes acceleration of hydrogen isotopes as soon as the gun geometry and operating parameters are optimized; theoretical models are being used to aid in this process. The hardware is being designed to accommodate repetitive operation, which is the objective of this research and is required for future applications.« less

Development of a two-stage light gas gun to accelerate hydrogen pellets to high speeds for plasma fueling applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Combs, S.K.; Milora, S.L.; Foust, C.R.

1988-01-01

The development of a two-stage light gas gun to accelerate hydrogen isotope pellets to high speeds is under way at Oak Ridge National Laboratory. High velocities (>2 km/s) are desirable for plasma fueling applications, since the faster pellets can penetrate more deeply into large, hot plasmas and deposit atoms of fuel directly in a larger fraction of the plasma volume. In the initial configuration of the two-stage device, a 2.2-l volume (/<=/55-bar) provides the gas to accelerate a 25.4-mm-diam piston in a 1-m-long pump tube; a burst disk or a fast valve initiates the acceleration process in the first stage.more » As the piston travels the length of the pump tube, the downstream gas (initially at <1 bar) is compressed (to pressures up to 2600 bar) and thus is driven to high temperature (approx.5000 K). This provides the driving force for acceleration of a 4-mm pellet in a 1-m-long gun barrel. In preliminary tests using helium as the driver in both stages, 35-mg plastic pellets have been accelerated to speeds as high as 3.8 km/s. Projectiles composed of hydrogen ice will have a mass in the range from 5 to 20 mg (/rho/ approx. 0.087, 0.20, and 0.32 g/cm/sup 3/ for frozen hydrogen isotopes). However, the use of sabots to encase and protect the cryogenic pellets from the high peak pressures will probably be required to realize speeds of approx.3 km/s or greater. The experimental plan includes acceleration of hydrogen isotopes as soon as the gun geometry and operating parameters are optimized; theoretical models are being used to aid in this process. The hardware is being designed to accommodate repetitive operation, which is the objective of this research and is required for future applications. 25 refs., 6 figs., 1 tab.« less

Laser-induced breakdown spectroscopy for analysis of plant materials: A review

NASA Astrophysics Data System (ADS)

Santos, Dário, Jr.; Nunes, Lidiane Cristina; de Carvalho, Gabriel Gustinelli Arantes; Gomes, Marcos da Silva; de Souza, Paulino Florêncio; Leme, Flavio de Oliveira; dos Santos, Luis Gustavo Cofani; Krug, Francisco José

2012-05-01

Developments and contributions of laser-induced breakdown spectroscopy (LIBS) for the determination of elements in plant materials are reviewed. Several applications where the solid samples are interrogated by simply focusing the laser pulses directly onto a fresh or dried surface of leaves, roots, fruits, vegetables, wood and pollen are presented. For quantitative purposes aiming at plant nutrition diagnosis, the test sample presentation in the form of pressed pellets, prepared from clean, dried and properly ground/homogenized leaves, and the use of univariate or multivariate calibration strategies are revisited.

Future loss of Arctic sea-ice cover could drive a substantial decrease in California's rainfall.

PubMed

Cvijanovic, Ivana; Santer, Benjamin D; Bonfils, Céline; Lucas, Donald D; Chiang, John C H; Zimmerman, Susan

2017-12-05

From 2012 to 2016, California experienced one of the worst droughts since the start of observational records. As in previous dry periods, precipitation-inducing winter storms were steered away from California by a persistent atmospheric ridging system in the North Pacific. Here we identify a new link between Arctic sea-ice loss and the North Pacific geopotential ridge development. In a two-step teleconnection, sea-ice changes lead to reorganization of tropical convection that in turn triggers an anticyclonic response over the North Pacific, resulting in significant drying over California. These findings suggest that the ability of climate models to accurately estimate future precipitation changes over California is also linked to the fidelity with which future sea-ice changes are simulated. We conclude that sea-ice loss of the magnitude expected in the next decades could substantially impact California's precipitation, thus highlighting another mechanism by which human-caused climate change could exacerbate future California droughts.

Thickness of tropical ice and photosynthesis on a snowball Earth

NASA Technical Reports Server (NTRS)

McKay, C. P.

2000-01-01

On a completely ice-covered "snowball" Earth the thickness of ice in the tropical regions would be limited by the sunlight penetrating into the ice cover and by the latent heat flux generated by freezing at the ice bottom--the freezing rate would balance the sublimation rate from the top of the ice cover. Heat transfer models of the perennially ice-covered Antarctic dry valley lakes applied to the snowball Earth indicate that the tropical ice cover would have a thickness of 10 m or less with a corresponding transmissivity of > 0.1%. This light level is adequate for photosynthesis and could explain the survival of the eukaryotic algae.

Thickness of tropical ice and photosynthesis on a snowball Earth.

PubMed

McKay, C P

2000-07-15

On a completely ice-covered "snowball" Earth the thickness of ice in the tropical regions would be limited by the sunlight penetrating into the ice cover and by the latent heat flux generated by freezing at the ice bottom--the freezing rate would balance the sublimation rate from the top of the ice cover. Heat transfer models of the perennially ice-covered Antarctic dry valley lakes applied to the snowball Earth indicate that the tropical ice cover would have a thickness of 10 m or less with a corresponding transmissivity of > 0.1%. This light level is adequate for photosynthesis and could explain the survival of the eukaryotic algae.

Engineering Design Handbook. Discontinuous Fiberglass Reinforced Thermoplastics

DTIC Science & Technology

1981-04-01

Fiberglass Type and Form Glass fibers are...Hall, Ltd. Figure 2-11. Stress vs Volume of Glass Fiber for Nylon and Polypropylene Glass Fiber E glass 12 Mm diam. Fibreglass Ltd Size ref...good dispersion of fiberglass in the end product with pelletized feed stocks. Glass fiber attrition is minimized with the dry blend technique,

Beneficial uses program. Progress report, period ending June 30, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-10-01

Progress in research on the irradiation of sewage sludge, the potential use of dried sewage sludge as animal feed or soil conditioners, the inactivation of rotavirus in sewage sludge, fruit fly control by the irradiation of citrus fruits, and the production of /sup 137/Cs source pellets is reported. (LCL)

Use of pelleted sericea lespedeza (Lespedeza cuneata) for natural control of coccidia and gastrointestinal nematodes in weaned goats

USDA-ARS?s Scientific Manuscript database

Infection with Eimeria spp. (coccidia) can be devastating in goats, particularly for young, recently-weaned kids, resulting in diarrhea, dehydration, and even death. Feeding dried sericea lespedeza [SL; Lespedeza cuneata (Dum.-Cours.) G. Don.] to young goats has been reported to reduce the effects ...

From the Lab Bench: Know your alternative feed

USDA-ARS?s Scientific Manuscript database

A column was written to discuss the need to know the nutritive value of the alternative feed (by- or co-product feeds) that you are feeding to your cattle. Alternative feeds can come in different physical forms: being either wet or dry, finely ground, crumbly or pelleted. Distiller’s and brewer’s ...

Effect of supplemental sericea lespedeza leaf meal pellets on gastrointestinal nematode infection in grazing goats

USDA-ARS?s Scientific Manuscript database

Feeding sun-dried sericea lespedeza [SL; Lespedeza cuneata (Dum-Cours.) G. Don.] reduces gastrointestinal nematode (GIN) infection in goats fed in confinement, but effects of this forage when fed as a supplement to goats on pasture are unclear. Two studies were completed in which supplemental feeds...

TiO2 gas sensor to detect the propanol at room temperature

NASA Astrophysics Data System (ADS)

Gaidan, Ibrahim; Asbia, Salim; Brabazon, Dermot; Ahad, Inam Ul

2017-10-01

Titanium dioxide (TiO2) was used as raw material to create sensing materials for gas sensor applications. The sample was mixed with isopropanol and wet-ball milled for 24 hours and then dried at 120°C to evaporate the solvent. Twenty grams of the dried powder was then pressed at 2 tons (27.58 MPa) using a pellet die. The pellet was heated at 1250°C in air for 5 hours and then milled for 10 minutes to powder form using a Gy-RO Mill machine. FIB and SEM analysis were used to study the microstructure of the materials. The polyvinyl butyral (5 wt.%) was used as a binder, while ethylenglycolmonobutylether served as a solvent to make a suitable paste. The paste was screen-printed on top of an alumina substrate that had copper electrodes to form the sensor. The sensor was used to detect propanol at room temperature over two different ranges (500 to 3000 ppm and 2500 to 5000 ppm). It was observed that the response of the device increased proportionally with increasing gas concentration repeatability.

Birth of kids after artificial insemination with sex-sorted, frozen-thawed goat spermatozoa.

PubMed

Bathgate, R; Mace, N; Heasman, K; Evans, G; Maxwell, W M C; de Graaf, S P

2013-12-01

Successful sex-sorting of goat spermatozoa and subsequent birth of pre-sexed kids have yet to be reported. As such, a series of experiments were conducted to develop protocols for sperm-sorting (using a modified flow cytometer, MoFlo SX(®) ) and cryopreservation of goat spermatozoa. Saanen goat spermatozoa (n = 2 males) were (i) collected into Salamon's or Tris catch media post-sorting and (ii) frozen in Tris-citrate-glucose media supplemented with 5, 10 or 20% egg yolk in (iii) 0.25 ml pellets on dry ice or 0.25 ml straws in a controlled-rate freezer. Post-sort and post-thaw sperm quality were assessed by motility (CASA), viability and acrosome integrity (PI/FITC-PNA). Sex-sorted goat spermatozoa frozen in pellets displayed significantly higher post-thaw motility and viability than spermatozoa frozen in straws. Catch media and differing egg yolk concentration had no effect on the sperm parameters tested. The in vitro and in vivo fertility of sex-sorted goat spermatozoa produced with this optimum protocol were then tested by means of a heterologous ova binding assay and intrauterine artificial insemination of Saanen goat does, respectively. Sex-sorted goat spermatozoa bound to sheep ova zona pellucidae in similar numbers (p > 0.05) to non-sorted goat spermatozoa, non-sorted ram spermatozoa and sex-sorted ram spermatozoa. Following intrauterine artificial insemination with sex-sorted spermatozoa, 38% (5/13) of does kidded with 83% (3/5) of kids being of the expected sex. Does inseminated with non-sorted spermatozoa achieved a 50% (3/6) kidding rate and a sex ratio of 3 : 1 (F : M). This study demonstrates for the first time that goat spermatozoa can be sex-sorted by flow cytometry, successfully frozen and used to produce pre-sexed kids. © 2013 Blackwell Verlag GmbH.

WATER-TRAPPED WORLDS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menou, Kristen

2013-09-01

Although tidally locked habitable planets orbiting nearby M-dwarf stars are among the best astronomical targets to search for extrasolar life, they may also be deficient in volatiles and water. Climate models for this class of planets show atmospheric transport of water from the dayside to the nightside, where it is precipitated as snow and trapped as ice. Since ice only slowly flows back to the dayside upon accumulation, the resulting hydrological cycle can trap a large amount of water in the form of nightside ice. Using ice sheet dynamical and thermodynamical constraints, I illustrate how planets with less than aboutmore » a quarter the Earth's oceans could trap most of their surface water on the nightside. This would leave their dayside, where habitable conditions are met, potentially dry. The amount and distribution of residual liquid water on the dayside depend on a variety of geophysical factors, including the efficiency of rock weathering at regulating atmospheric CO{sub 2} as dayside ocean basins dry up. Water-trapped worlds with dry daysides may offer similar advantages as land planets for habitability, by contrast with worlds where more abundant water freely flows around the globe.« less

Thermal transfer in extracted incisors during thermal pulp sensitivity testing.

PubMed

Linsuwanont, P; Palamara, J E; Messer, H H

2008-03-01

To measure the temperature distribution within tooth structure during and after application of thermal stimuli used during pulp sensitivity testing. Extracted intact human maxillary anterior teeth were investigated for temperature changes at the labial enamel, the dentino-enamel junction (DEJ) and pulpal surface during and after a 5-s application of six different thermal stimuli: hot water (80 degrees C), heated gutta-percha (140 degrees C), carbon dioxide dry ice (-72 degrees C), refrigerant spray (-50 degrees C), ice stick (0 degrees C) and cold water (2 degrees C). J-type thermocouples and heat conduction paste were used to detect temperature changes, together with a data acquisition system (Labview). Data were analysed using analysis of variance, with a confidence level of P < 0.05. Temperature change was detected more quickly at the DEJ and pulpal surface with the application of hot water, heated gutta-percha and refrigerant spray than with carbon dioxide dry ice and ice (P < 0.05). Cold water and refrigerant spray were in the same range in terms of time to detect temperature change at both the DEJ and pulpal surface. Thermal stimuli with greater temperature difference from tooth temperature created a greater thermal gradient initially, followed by a greater temperature change at the DEJ and the pulpal surface. In this regard, ice and cold water were weaker stimuli than others (P < 0.05). Thermal stimuli used in pulp testing are highly variable in terms of temperature of the stimulus, rate of thermal transfer to the tooth and extent of temperature change within tooth structure. Overall, dry ice and refrigerant spray provide the most consistent stimuli, whereas heated gutta-percha and hot water were highly variable. Ice was a weak stimulus.

Effects of alfalfa hay and its physical form (chopped versus pelleted) on performance of Holstein calves.

PubMed

Jahani-Moghadam, M; Mahjoubi, E; Hossein Yazdi, M; Cardoso, F C; Drackley, J K

2015-06-01

Inclusion of forage and its physical form in starter may affect rumen development, average daily gain (ADG), and dry matter intake (DMI) of dairy calves. To evaluate the effects of forage and its physical form (chopped vs. pelleted) on growth of calves under a high milk feeding regimen, 32 Holstein calves (38.8±1.1kg) were assigned at birth to 1 of 3 treatments in a completely randomized block design. Dietary treatments (% of dry matter) were (1) 100% semi-texturized starter (CON); (2) 90% semi-texturized starter + 10% chopped alfalfa hay (mean particle size=5.4mm) as a total mixed ration (TMR; CH); and (3) 90% semi-texturized starter + 10% pelleted alfalfa (mean=5.8mm) hay as a TMR (PH). Data were subjected to mixed model analysis with contrasts used to evaluate effect of forage inclusion. Calves were weaned at 76 d of age and the experiment finished 2 wk after weaning. Individual milk and solid feed consumption were recorded daily. Solid feed consumption and ADG increased as age increased (effect of week), but neither forage inclusion nor physical form of forage affected these variables pre- or postweaning. Plasma urea N was affected by treatments such that the CON group had a lower concentration than forage-fed groups. Forage inclusion, but not physical form, resulted in increased total protein in plasma. Although days with elevated rectal temperature, fecal score, and general appearance were not affected by dietary treatments, calves fed alfalfa hay during the first month of life had fewer days with respiratory issues, regardless of physical form of hay. We concluded that provision of forage does have some beneficial effects in calves fed large amounts of milk replacer, but pelleted alfalfa hay did not result in any improvement in calf performance or health. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Microwave-Assisted Alkali Pre-Treatment, Densification and Enzymatic Saccharification of Canola Straw and Oat Hull.

PubMed

Agu, Obiora S; Tabil, Lope G; Dumonceaux, Tim

2017-03-26

The effects of microwave-assisted alkali pre-treatment on pellets' characteristics and enzymatic saccharification for bioethanol production using lignocellulosic biomass of canola straw and oat hull were investigated. The ground canola straw and oat hull were immersed in distilled water, sodium hydroxide and potassium hydroxide solutions at two concentrations (0.75% and 1.5% w/v) and exposed to microwave radiation at power level 713 W and three residence times (6, 12 and 18 min). Bulk and particle densities of ground biomass samples were determined. Alkaline-microwave pre-treated and untreated samples were subjected to single pelleting test in an Instron universal machine, pre-set to a load of 4000 N. The measured parameters, pellet density, tensile strength and dimensional stability were evaluated and the results showed that the microwave-assisted alkali pre-treated pellets had a significantly higher density and tensile strength compared to samples that were untreated or pre-treated by microwave alone. The chemical composition analysis showed that microwave-assisted alkali pre-treatment was able to disrupt and break down the lignocellulosic structure of the samples, creating an area of cellulose accessible to cellulase reactivity. The best enzymatic saccharification results gave a high glucose yield of 110.05 mg/g dry sample for canola straw ground in a 1.6 mm screen hammer mill and pre-treated with 1.5% NaOH for 18 min, and a 99.10 mg/g dry sample for oat hull ground in a 1.6 mm screen hammer mill and pre-treated with 0.75% NaOH for 18 min microwave-assisted alkali pre-treatments. The effects of pre-treatment results were supported by SEM analysis. Overall, it was found that microwave-assisted alkali pre-treatment of canola straw and oat hull at a short residence time enhanced glucose yield.

Cross-Section of Icy Soil

NASA Image and Video Library

2002-05-28

This diagram shows a possible configuration of ice-rich and dry soil in the upper meter 3 feet of Mars. The ice-rich soil was detected by the gamma ray spectrometer suite of instruments aboard NASA Mars Odyssey spacecraft.

Sulfur dioxide reactions on ice surfaces: Implications for dry deposition to snow

Treesearch

Martha H. Conklin; Richard A. Sommerfeld; S. Kay Laird; John E. Villinski

1993-01-01

Controlled exposure of ice to a reactive gas, SO2, demonstrated the importance of the chemical composition of the ice surface on the accumulation of acidity in snow. In a series of bench-scale continuous-flow column experiments run at four temperatures (-1, -8, -30 and -60°C), SO2 was shown to dissolve and to react with other species in the ice-air interfacial region...

The effect on Arctic climate of atmospheric meridional energy-transport changes studied based on the CESM climate model

NASA Astrophysics Data System (ADS)

Grand Graversen, Rune

2017-04-01

The Arctic amplification of global warming, and the pronounced Arctic sea-ice retreat constitute some of the most alarming signs of global climate change. These Arctic changes are likely a consequence of a combination of several processes, for instance enhanced uptake of solar radiation in the Arctic due to a decrease of sea ice (the ice-albedo feedback), and increase in the local Arctic greenhouse effect due to enhanced moister flux from lower latitudes. Many of the proposed processes appear to be dependent on each other, for instance an increase in water-vapour advection to the Arctic enhances the greenhouse effect in the Arctic and the longwave radiation to the surface, leading to sea-ice melt and enhancement of the ice-albedo feedback. The effects of albedo changes and other radiative feedbacks have been investigated in earlier studies based on model experiments designed to examine these effects specifically. Here we instead focus on the effects of meridional transport changes into the Arctic, both of moister and dry-static energy. Hence we here present results of model experiments with the CESM climate model designed specifically to extract the effects of the changes of the two transport components. In the CESM model the moister transport to the Arctic increases, whereas the dry-static transport decreases in response to a doubling of CO2. This is in agreement with other model results. The model is now forced with these transport changes of water-vapour and dry-static energy associated with a CO2 doubling. The results show that changes of the water-vapour transport lead to Arctic warming. This is partly a consequence of the ice-albedo feedback due to sea-ice melt caused by the change of the water-vapour advection. The changes of the dry-static transport lead to Arctic cooling, which however is smaller than the warming induced by the water-vapour component. Hence this study support the hypothesis that changes in the atmospheric circulation contribute to the Arctic temperature amplification of the ongoing global warming.

Effect of hot-boned pork on the keeping quality of fresh pork sausage.

PubMed

Guerrero Legarreta, I; Usborne, W R; Ashton, G C

1987-01-01

The first experiment evaluated the effect of solid carbon dioxide (dry ice) addition to hot-boned meat, in different proportions, upon the keeping quality of fresh pork sausage patties. Dry ice had some negative effects at levels of 20% to 40%, such as hardening and colour fading of samples, although it increased water-holding capacity of the sausage. In the second experiment three proportions of hot-boned meat and chilled meat were evaluated as a means to extend the retail storage time of fresh pork sausage links. Hot-boned pork was treated by three methods: freezing the meat before grinding, salting and freezing, and salting plus dry ice addition. The results favoured the use of 50% hot-boned meat and 50% chilled meat, for which the lowest hardness and oxidation values were obtained. Microbial counts and hue values showed no significant variation among the three treatments. Salting and freezing hot-boned meat before grinding was the method which produced the best overall quality. Copyright © 1987. Published by Elsevier Ltd.

NASA/FAA Tailplane Icing Program Overview

NASA Technical Reports Server (NTRS)

Ratvasky, Thomas P.; VanZante, Judith Foss; Riley, James T.

1999-01-01

The effects of tailplane icing were investigated in a four-year NASA/FAA Tailplane Icing, Program (TIP). This research program was developed to improve the understanding, of iced tailplane aeroperformance and aircraft aerodynamics, and to develop design and training aides to help reduce the number of incidents and accidents caused by tailplane icing. To do this, the TIP was constructed with elements that included icing, wind tunnel testing, dry-air aerodynamic wind tunnel testing, flight tests, and analytical code development. This paper provides an overview of the entire program demonstrating the interconnectivity of the program elements and reports on current accomplishments.

Luminescence dating of paleolake deltas and glacial deposits in Garwood Valley, Antarctica: Implications for climate, Ross ice sheet dynamics, and paleolake duration

USGS Publications Warehouse

Levy, Joseph S.; Rittenour, Tammy M.; Fountain, Andrew G.; O'Connor, Jim E.

2017-01-01

The formation of perched deltas and other lacustrine deposits in the McMurdo Dry Valleys of Antarctica is widely considered to be evidence of valley-filling lakes dammed by the grounded Ross Sea ice sheet during the local Last Glacial Maximum, with lake drainage interpreted as a record of grounding line retreat. We used luminescence dating to determine the age of paleolake deltas and glacial tills in Garwood Valley, a coastal dry valley that opens to the Ross Sea. Luminescence ages are stratigraphically consistent with radiocarbon results from algal mats within the same delta deposits but suggest radiocarbon dates from lacustrine carbonates may overestimate deposit ages by thousands of years. Results suggest that late Holocene delta deposition into paleolake Howard in Garwood Valley persisted until ca. 3.5 ka. This is significantly younger than the date when grounded ice is thought to have retreated from the Ross Sea. Our evidence suggests that the local, stranded ice-cored till topography in Garwood Valley, rather than regional ice-sheet dynamics, may have controlled lake levels for some McMurdo Dry Valleys paleolakes. Age control from the supraglacial Ross Sea drift suggests grounding and up-valley advance of the Ross Sea ice sheet into Garwood valley during marine oxygen isotope stage (MIS) 4 (71–78 ka) and the local Last Glacial Maximum (9–10 ka). This work demonstrates the power of combining luminescence dating with existing radiocarbon data sets to improve understanding of the relationships among paleolake formation, glacial position, and stream discharge in response to climate change.

Oxytocin Levels in Community-Collected Saliva Samples Transported by Dry Versus Wet Ice.

PubMed

Howland, Lois C; Pickler, Rita H; Sullenbarger, Brent A; Connelly, Cynthia D

2018-01-01

Oxytocin (OT), a neuropeptide produced primarily in the hypothalamus, is associated with both critical physiological and psychological processes, particularly stress and feelings of affiliation. Increasingly, researchers are seeking ways to reliably incorporate OT as an outcome biomarker in clinical research. Previously, OT levels were measured in plasma or urine. Recently, researchers have measured this biomarker in saliva, particularly when conducting research in clinical and community settings. In spite of increased interest in the use of salivary OT in clinical research, procedures for handling, transport, and analysis of specimens vary. It is not known if significant OT protein degradation occurs if samples are initially transported on wet ice before being frozen. The aim of this study is to evaluate the effect of transport media (wet vs. dry ice) on OT levels derived from saliva collected from 12 postpartum women residing in the community. Saliva collected from each participant was divided between two microcentrifuge tubes (MIDSCI, Valley Park, MO), one placed on wet ice and one on dry ice for transport from the participant's home to the laboratory freezer. Time from collection to storage freezer was recorded. Laboratory personnel, blinded to method of transport, batch processed the samples. No significant differences in OT levels were found by transport method. Despite large interperson variations in OT levels, there were negligible intraperson variations. Although further research is required to identify factors (including transport time) related to interperson variation, this study supports the use of wet ice as a means of transporting salivary OT specimens in community-based research.

Effects of canola meal pellet conditioning temperature and time on ruminal and intestinal digestion, hourly effective degradation ratio, and potential nitrogen to energy synchronization in dairy cows.

PubMed

Huang, Xuewei; Khan, Nazir A; Zhang, Xuewei; Yu, Peiqiang

2015-12-01

The increase in bio-oil production in North America has resulted in millions of tonnes of co-products: canola meal and carinata meal. Little research has been conducted to determine the effect of pellet conditioning temperature, time, and their interaction on processing-induced changes in nutrient digestibility in the rumen and intestine (in vitro) of dairy cattle. The objectives of this study were to investigate the effects of conditioning temperature (70, 80, and 90°C), time (50 and 75 s), and their interaction (temperature × time) during the pelleting of canola meal on (1) rumen degradation kinetics and effective rumen degradability of dry matter, crude protein (CP), and neutral detergent fiber; (2) intestinal digestibility of rumen-undegradable protein (RUP); and (3) hourly effective rumen degradation ratio and potential N to energy synchronization in dairy cattle. The results showed that the temperature and duration of pellet conditioning significantly altered the degradation characteristics of nutrients in the rumen. Pelleting increased CP degradation in the rumen, and CP digestion site was shifted to the rumen rather than to the small intestine. When conditioning temperature was set 80°C, the rumen degradation of CP and neutral detergent fiber was highest, but postrumen digestion was lowest. With respect to intestinal digestion, the available CP for intestinal digestion became less because of reduced RUP supply to the small intestine. The pelleting process tended to significantly affect the intestinal digestibility of RUP. However, the total digestible CP content of canola meal was not affected. In conclusion, pelleting induced changes in rumen and intestinal digestion profiles, and altered the potential N to energy synchronization and hourly effective rumen degradation ratio of canola meal in dairy cattle. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Controlled ice nucleation using freeze-dried Pseudomonas syringae encapsulated in alginate beads.

PubMed

Weng, Lindong; Tessier, Shannon N; Swei, Anisa; Stott, Shannon L; Toner, Mehmet

2017-04-01

The control of ice nucleation is of fundamental significance in many process technologies related to food and pharmaceutical science and cryobiology. Mechanical perturbation, electromagnetic fields and ice-nucleating agents (INAs) have been known to induce ice nucleation in a controlled manner. But these ice-nucleating methods may suffer from cumbersome manual operations, safety concerns of external fields, and biocompatibility and recovery issues of INA particles, especially when used in living systems. Given the automatic ice-seeding nature of INAs, a promising solution to overcome some of the above limitations is to engineer a biocomposite that accommodates the INA particles but minimizes their interactions with biologics, as well as enabling the recovery of used particles. In this study, freeze-dried Pseudomonas syringae, a model ice-nucleating agent, was encapsulated into microliter-sized alginate beads. We evaluated the performance of the bacterial hydrogel beads to initiate ice nucleation in water and aqueous glycerol solution by investigating factors including the size and number of the beads and the local concentration of INA particles. In the aqueous sample of a fixed volume, the total mass of the INA particles (m) was found to be the governing parameter that is solely responsible for determining the ice nucleation performance of the bacterial hydrogel beads. The freezing temperature has a strong positive linear correlation with log 10 m. The findings in this study provide an effective, predictable approach to control ice nucleation, which can improve the outcome and standardization of many ice-assisted process technologies. Copyright © 2017 Elsevier Inc. All rights reserved.

29 CFR 776.21 - “For” commerce.

Code of Federal Regulations, 2013 CFR

2013-07-01

... essentially local ice plant where the only basis of coverage is the delivery of ice for the water cooler in... entitled to be paid on that basis notwithstanding some of the wells drilled may eventually prove to be dry...

29 CFR 776.21 - “For” commerce.

Code of Federal Regulations, 2014 CFR

2014-07-01

... essentially local ice plant where the only basis of coverage is the delivery of ice for the water cooler in... entitled to be paid on that basis notwithstanding some of the wells drilled may eventually prove to be dry...

29 CFR 776.21 - “For” commerce.

Code of Federal Regulations, 2011 CFR

2011-07-01

... essentially local ice plant where the only basis of coverage is the delivery of ice for the water cooler in... entitled to be paid on that basis notwithstanding some of the wells drilled may eventually prove to be dry...

On Localized Vapor Pressure Gradients Governing Condensation and Frost Phenomena.

PubMed

Nath, Saurabh; Boreyko, Jonathan B

2016-08-23

Interdroplet vapor pressure gradients are the driving mechanism for several phase-change phenomena such as condensation dry zones, interdroplet ice bridging, dry zones around ice, and frost halos. Despite the fundamental nature of the underlying pressure gradients, the majority of studies on these emerging phenomena have been primarily empirical. Using classical nucleation theory and Becker-Döring embryo formation kinetics, here we calculate the pressure field for all possible modes of condensation and desublimation in order to gain fundamental insight into how pressure gradients govern the behavior of dry zones, condensation frosting, and frost halos. Our findings reveal that in a variety of phase-change systems the thermodynamically favorable mode of nucleation can switch between condensation and desublimation depending upon the temperature and wettability of the surface. The calculated pressure field is used to model the length of a dry zone around liquid or ice droplets over a broad parameter space. The long-standing question of whether the vapor pressure at the interface of growing frost is saturated or supersaturated is resolved by considering the kinetics of interdroplet ice bridging. Finally, on the basis of theoretical calculations, we propose that there exists a new mode of frost halo that is yet to be experimentally observed; a bimodal phase map is developed, demonstrating its dependence on the temperature and wettability of the underlying substrate. We hope that the model and predictions contained herein will assist future efforts to exploit localized vapor pressure gradients for the design of spatially controlled or antifrosting phase-change systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anameric, B.; Kawatra, S.K.

Pig iron nuggets were produced in a laboratory-scale furnace at Michigan Technological University. The process was intended to replicate Kobe Steel's ITmk3 direct ironmaking process. These nuggets were produced from pellets that were made from a mixture of iron oxide, coal, flux and a binder and heated in a furnace with a chamber temperature of 1450{sup o}C. The pellets then self-reduced to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate liquid slag phase formed that cleanly separated from the molten metal. The physical and chemical properties of the pig iron nuggetsmore » were similar to pig iron produced by blast furnaces, which is distinct from direct reduced iron (DRI).« less

46 CFR 148.310 - Seed cake.

Code of Federal Regulations, 2011 CFR

2011-10-01

... apply to solvent-extracted rape seed meal, pellets, soya bean meal, cotton seed meal, or sunflower seed meal that— (1) Contains a maximum of 4 percent vegetable oil and a maximum of 15 percent vegetable oil... cake. (e) The seed cake must be kept as dry as practical at all times. (f) If the seed cake is solvent...

A microhistological technique for analysis of food habits of mycophagous rodents.

Treesearch

Patrick W. McIntire; Andrew B. Carey

1989-01-01

We present a technique, based on microhistological analysis of fecal pellets, for quantifying the diets of forest rodents. This technique provides for the simultaneous recording of fungal spores and vascular plant material. Fecal samples should be freeze dried, weighed, and rehydrated with distilled water. We recommend a minimum sampling intensity of 50 fields of view...

The effects of supplemental Sericea lespedeza pellets in lambs and kids. 1. Growth rate

USDA-ARS?s Scientific Manuscript database

Sericea lespedeza (SL; Lespedeza cuneata) has been used in recent years to aid in the control of gastrointestinal nematodes (GIN) in sheep and goats. Grazing or feeding dried SL leads to a reduction in egg production by GIN and reduces coccidiosis. Growth rates in lambs and kids when fed SL for mo...

The Effects of Radiation on the Adsorption of CO2 by Nonice Materials Relevant to Icy Satellites

NASA Astrophysics Data System (ADS)

Hibbitts, C.; Stockstill-Cahill, K.; Paranicas, C.; Wing, B. R.

2017-12-01

Water-ice and water-rich non-ice materials dominate the surfaces of the icy satellites of Jupiter and Saturn, with CO2 detected at trace amounts largely in the nonice materials [1,2]. Although, the mechanism by which CO2 is entrained within the nonice material has not yet been understood, one hypothesis is adsorption by van der Waals forces or induced dipole interactions, with laboratory measurements demonstrating some analog materials can stably retain adsorbed CO2 while under vacuum at the temperatures of the icy satellites [3,4]. The strength and spectral signature of the adsorbed CO2 is dependent upon the composition and temperature of the host material. So far, the most adsorptive analogs are complex expansive clays, probably because of the large microporosity and presence of charge compensating cations to act as adsorption sites. However, the surfaces of the airless Galilean and Saturnian satellites are bombarded by high-energy particles from the planetary magnetospheres, which could alter the nonice material affecting adsorptivity towards CO2 (and other volatiles). Thus, we have conducted experiments to explore the possibility that irradiation could increase the adsorptivity of other analogs more consistent with the expected composition of the satellites surfaces. This hypothesis is explored for CO2 adsorption onto pressed powder pellets that are cooled to the surface temperatures of the satellites' surfaces under solar illumination ( 125-150 K) and dosed with CO2 from directly above the surface of the pellet, while collecting spectra of the asymmetric stretch fundamental of the CO2 absorption band near 4.25 microns. After this initial spectrum, the pellet is warmed to degas any adsorbed CO2 and then recooled. The pellet is then irradiated with 40 keV electrons for 48-72 hours at a fluence of 80 microamps and the adsorption experiment is repeated. The infrared spectrum is a bidirectional reflectance measurement using a Bruker Vertex 70 FTIR with and external MCT detector and the chamber pressure 1e-8 torr or lower. References: [1] McCord et al. 1998. J. Geophys. Res., 103, E4, 8603-8626; [2] Clark et al. 2005. Nature, 435, 66-69; [3] Hibbitts, C.A. and J. Szanyi. 2007. Icarus, 191, 371-380; [4] Berlanga, G. et al., 2016. Icarus, 280, 366-377.

Effect of Surface Omniphobicity on Drying by Forced Convection (Briefing Charts)

DTIC Science & Technology

2015-08-01

Lesson Plan • This lesson plan is directed for 9th-12th grade students. • Reading about ice - cream . • Learning to make ice - cream through a DOE...average of different ice - creams . 15DISTRIBUTION A: Approved for public release; distribution unlimited. AFRL Public Affairs Clearance # Future...optimization. • The three factors are different weight percent of salt per ice , fat content in dairy and shaking time. • Measured output will be rating and

Climate change and forest fires synergistically drive widespread melt events of the Greenland Ice Sheet.

PubMed

Keegan, Kaitlin M; Albert, Mary R; McConnell, Joseph R; Baker, Ian

2014-06-03

In July 2012, over 97% of the Greenland Ice Sheet experienced surface melt, the first widespread melt during the era of satellite remote sensing. Analysis of six Greenland shallow firn cores from the dry snow region confirms that the most recent prior widespread melt occurred in 1889. A firn core from the center of the ice sheet demonstrated that exceptionally warm temperatures combined with black carbon sediments from Northern Hemisphere forest fires reduced albedo below a critical threshold in the dry snow region, and caused the melting events in both 1889 and 2012. We use these data to project the frequency of widespread melt into the year 2100. Since Arctic temperatures and the frequency of forest fires are both expected to rise with climate change, our results suggest that widespread melt events on the Greenland Ice Sheet may begin to occur almost annually by the end of century. These events are likely to alter the surface mass balance of the ice sheet, leaving the surface susceptible to further melting.

Squiggles in Hellas Planitia

NASA Image and Video Library

2017-10-25

At around 2,200 kilometers in diameter, Hellas Planitia is the largest visible impact basin in the Solar System, and hosts the lowest elevations on Mars' surface as well as a variety of landscapes. This image from NASA's Mars Reconnaisance Orbiter (MRO) covers a small central portion of the basin and shows a dune field with lots of dust devil trails. In the middle, we see what appears to be long and straight "scratch marks" running down the southeast (bottom-right) facing dune slopes. If we look closer, we can see these scratch marks actually squiggle back and forth on their way down the dune. These scratch marks are linear gullies. Just like on Earth, high-latitude regions on Mars are covered with frost in the winter. However, the winter frost on Mars is made of carbon dioxide ice (dry ice) instead of water ice. We believe linear gullies are the result of this dry ice breaking apart into blocks, which then slide or roll down warmer sandy slopes, sublimating and carving as they go. The linear gullies exhibit exceptional sinuosity (the squiggle pattern) and we believe this to be the result of repeated movement of dry ice blocks in the same path, possibly in combination with different hardness or flow resistance of the sand within the dune slopes. Determining the specific process that causes the formation and evolution of sinuosity in linear gullies is a question scientists are still trying to answer. What do you think causes the squiggles? https://photojournal.jpl.nasa.gov/catalog/PIA22052

The application of dual-electrode through vial impedance spectroscopy for the determination of ice interface temperatures, primary drying rate and vial heat transfer coefficient in lyophilization process development.

PubMed

Smith, Geoff; Jeeraruangrattana, Yowwares; Ermolina, Irina

2018-06-22

Through vial impedance spectroscopy (TVIS) is a product non-invasive process analytical technology which exploits the frequency dependence of the complex impedance spectrum of a composite object (i.e. the freeze-drying vial and its contents) in order to track the progression of the freeze-drying cycle. This work demonstrates the use of a dual electrode system, attached to the external surface of a type I glass tubing vial (nominal capacity 10 mL) in the prediction of (i) the ice interface temperatures at the sublimation front and at the base of the vial, and (ii) the primary drying rate. A value for the heat transfer coefficient (for a chamber pressure of 270 µbar) was then calculated from these parameters and shown to be comparable to that published by Tchessalov[1]. Copyright © 2018. Published by Elsevier B.V.

Amputation - traumatic

MedlinePlus

... DO NOT put the body part directly in water without using a plastic bag. DO NOT put the severed part directly on ice. DO NOT use dry ice as this will cause frostbite and injury to the part. If cold water is not available, keep the part away from ...

Nonlinear Spectral Mixture Modeling to Estimate Water-Ice Abundance of Martian Regolith

NASA Astrophysics Data System (ADS)

Gyalay, Szilard; Chu, Kathryn; Zeev Noe Dobrea, Eldar

2017-10-01

We present a novel technique to estimate the abundance of water-ice in the Martian permafrost using Phoenix Surface Stereo Imager multispectral data. In previous work, Cull et al. (2010) estimated the abundance of water-ice in trenches dug by the Mars Phoenix lander by modeling the spectra of the icy regolith using the radiative transfer methods described in Hapke (2008) with optical constants for Mauna Kea palagonite (Clancy et al., 1995) as a substitute for unknown Martian regolith optical constants. Our technique, which uses the radiative transfer methods described in Shkuratov et al. (1999), seeks to eliminate the uncertainty that stems from not knowing the composition of the Martian regolith by using observations of the Martian soil before and after the water-ice has sublimated away. We use observations of the desiccated regolith sample to estimate its complex index of refraction from its spectrum. This removes any a priori assumptions of Martian regolith composition, limiting our free parameters to the estimated real index of refraction of the dry regolith at one specific wavelength, ice grain size, and regolith porosity. We can then model mixtures of regolith and water-ice, fitting to the original icy spectrum to estimate the ice abundance. To constrain the uncertainties in this technique, we performed laboratory measurements of the spectra of known mixtures of water-ice and dry soils as well as those of soils after desiccation with controlled viewing geometries. Finally, we applied the technique to Phoenix Surface Stereo Imager observations and estimated water-ice abundances consistent with pore-fill in the near-surface ice. This abundance is consistent with atmospheric diffusion, which has implications to our understanding of the history of water-ice on Mars and the role of the regolith at high latitudes as a reservoir of atmospheric H2O.

Paleolimnology of the McMurdo Dry Valleys, Antarctica

NASA Technical Reports Server (NTRS)

Doran, P. T.; Wharton, R. A. Jr; Lyons, W. B.; Wharton RA, J. r. (Principal Investigator)

1994-01-01

The McMurdo Dry Valleys presently contain more than 20 permanent lakes and ponds, which vary markedly in character. All, with the exception of a hypersaline pond, have a perennial ice-cover. The dry valley lakes, and lakes in other ice-free regions of continental Antarctica, are unique on this planet in that they consistently maintain a thick year-round ice cover (2.8-6.0 m) over liquid water. The persistent ice covers minimize wind-generated currents and reduce light penetration, as well as restricting sediment deposition into a lake and the exchange of atmospheric gases between the water column and the atmosphere. From a paleolimnological perspective, the dry valley lakes offer an important record of catchment and environmental changes. These lakes are also modern-day equivalents of periglacial lakes that were common during glacial periods at temperate latitudes. The present lakes are mostly remnants of larger glacial lakes that occupied the valleys in the past, perhaps up to 4.6 Ma ago. Two of the valleys contain evidence of being filled with large glacial lakes within the last 10000 years. Repeated drying and filling events since then have left a characteristic impression on the salt profiles of some lakes creating a unique paleo-indicator within the water column. These events are also marked in the sediments by the concentration and dilution of certain chemical constituents, particularly salts, and are also corroborated by carbonate speciation and oxygen isotope analysis. Stratigraphic analysis of dry valley lake sediments is made difficult by the occurrence of an 'old carbon' reservoir creating spurious radiocarbon dates, and by the high degree of spatial variability in lake sedimentation. From a biological perspective, the lakes are relatively simple, containing various taxa of planktonic and benthic microorganisms, but no higher forms of life, which is an advantage to paleolimnologists because there is no bioturbation in the sediments. Useful biological paleo-indicators found in the sediments include cyanobacterial filament sheaths, diatom frustules and other eukaryotic algal cells, protozoan cysts, photosynthetic pigments, and minerals (e.g. carbonates) associated with microbial activity. Future work will benefit from fully characterizing the connection between the ice covers, environmental conditions, and paleo-indicators, thereby allowing refinement of inferences made concerning the paleoenvironment. New dating techniques need to be tested in this environment to overcome the problems associated with radiocarbon dating. The establishment of a detailed and focused paleolimnological campaign is proposed.

Paleolimnology of the McMurdo Dry Valleys, Antarctica.

PubMed

Doran, P T; Wharton, R A; Lyons, W B

1994-01-01

The McMurdo Dry Valleys presently contain more than 20 permanent lakes and ponds, which vary markedly in character. All, with the exception of a hypersaline pond, have a perennial ice-cover. The dry valley lakes, and lakes in other ice-free regions of continental Antarctica, are unique on this planet in that they consistently maintain a thick year-round ice cover (2.8-6.0 m) over liquid water. The persistent ice covers minimize wind-generated currents and reduce light penetration, as well as restricting sediment deposition into a lake and the exchange of atmospheric gases between the water column and the atmosphere. From a paleolimnological perspective, the dry valley lakes offer an important record of catchment and environmental changes. These lakes are also modern-day equivalents of periglacial lakes that were common during glacial periods at temperate latitudes. The present lakes are mostly remnants of larger glacial lakes that occupied the valleys in the past, perhaps up to 4.6 Ma ago. Two of the valleys contain evidence of being filled with large glacial lakes within the last 10000 years. Repeated drying and filling events since then have left a characteristic impression on the salt profiles of some lakes creating a unique paleo-indicator within the water column. These events are also marked in the sediments by the concentration and dilution of certain chemical constituents, particularly salts, and are also corroborated by carbonate speciation and oxygen isotope analysis. Stratigraphic analysis of dry valley lake sediments is made difficult by the occurrence of an 'old carbon' reservoir creating spurious radiocarbon dates, and by the high degree of spatial variability in lake sedimentation. From a biological perspective, the lakes are relatively simple, containing various taxa of planktonic and benthic microorganisms, but no higher forms of life, which is an advantage to paleolimnologists because there is no bioturbation in the sediments. Useful biological paleo-indicators found in the sediments include cyanobacterial filament sheaths, diatom frustules and other eukaryotic algal cells, protozoan cysts, photosynthetic pigments, and minerals (e.g. carbonates) associated with microbial activity. Future work will benefit from fully characterizing the connection between the ice covers, environmental conditions, and paleo-indicators, thereby allowing refinement of inferences made concerning the paleoenvironment. New dating techniques need to be tested in this environment to overcome the problems associated with radiocarbon dating. The establishment of a detailed and focused paleolimnological campaign is proposed.

Through-vial impedance spectroscopy of the mechanisms of annealing in the freeze-drying of maltodextrin: the impact of annealing hold time and temperature on the primary drying rate.

PubMed

Smith, Geoff; Arshad, Muhammad Sohail; Polygalov, Eugene; Ermolina, Irina

2014-06-01

The study aims to investigate the impact of annealing hold time and temperature on the primary drying rate/duration of a 10% (w/v) solution of maltodextrin with an emphasis on how the mechanisms of annealing might be understood from the in-vial measurements of the ice crystal growth and the glass transition. The electrical impedance of the solution within a modified glass vial was recorded between 10 and 10(6) Hz during freeze-drying cycles with varying annealing hold times (1-5 h) and temperatures. Primary drying times decreased by 7%, 27% and 34% (1.1, 4.3 and 5.5 h) with the inclusion of an annealing step at temperatures of -15°C, -10°C and -5°C, respectively. The glass transition was recorded at approximately -16°C during the re-heating and re-cooling steps, which is close to the glass transition (Tg ') reported for 10% (w/v) maltodextrin and therefore indicates that a maximum freeze concentration (∼86%, w/w, from the Gordon-Taylor equation) was achieved during first freezing, with no further ice being formed on annealing. This observation, coupled to the decrease in electrical resistance that was observed during the annealing hold time, suggests that the reduction in the drying time was because of improved connectivity of ice crystals because of Ostwald ripening rather than devitrification. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Investigation of sewage sludge treatment using air plasma assisted gasification.

PubMed

Striūgas, Nerijus; Valinčius, Vitas; Pedišius, Nerijus; Poškas, Robertas; Zakarauskas, Kęstutis

2017-06-01

This study presents an experimental investigation of downdraft gasification process coupled with a secondary thermal plasma reactor in order to perform experimental investigations of sewage sludge gasification, and compare process parameters running the system with and without the secondary thermal plasma reactor. The experimental investigation were performed with non-pelletized mixture of dried sewage sludge and wood pellets. To estimate the process performance, the composition of the producer gas, tars, particle matter, producer gas and char yield were measured at the exit of the gasification and plasma reactor. The research revealed the distribution of selected metals and chlorine in the process products and examined a possible formation of hexachlorobenzene. It determined that the plasma assisted processing of gaseous products changes the composition of the tars and the producer gas, mostly by destruction of hydrocarbon species, such as methane, acetylene, ethane or propane. Plasma processing of the producer gas reduces their calorific value but increases the gas yield and the total produced energy amount. The presented technology demonstrated capability both for applying to reduce the accumulation of the sewage sludge and production of substitute gas for drying of sewage sludge and electrical power. Copyright © 2017 Elsevier Ltd. All rights reserved.

Doppler weather radar observations of the 2009 eruption of Redoubt Volcano, Alaska

USGS Publications Warehouse

Schneider, David J.; Hoblitt, Richard P.

2013-01-01

The U.S. Geological Survey (USGS) deployed a transportable Doppler C-band radar during the precursory stage of the 2009 eruption of Redoubt Volcano, Alaska that provided valuable information during subsequent explosive events. We describe the capabilities of this new monitoring tool and present data captured during the Redoubt eruption. The MiniMax 250-C (MM-250C) radar detected seventeen of the nineteen largest explosive events between March 23 and April 4, 2009. Sixteen of these events reached the stratosphere (above 10 km) within 2–5 min of explosion onset. High column and proximal cloud reflectivity values (50 to 60 dBZ) were observed from many of these events, and were likely due to the formation of mm-sized accretionary tephra-ice pellets. Reflectivity data suggest that these pellets formed within the first few minutes of explosion onset. Rapid sedimentation of the mm-sized pellets was observed as a decrease in maximum detection cloud height. The volcanic cloud from the April 4 explosive event showed lower reflectivity values, due to finer particle sizes (related to dome collapse and related pyroclastic flows) and lack of significant pellet formation. Eruption durations determined by the radar were within a factor of two compared to seismic and pressure-sensor derived estimates, and were not well correlated. Ash dispersion observed by the radar was primarily in the upper troposphere below 10 km, but satellite observations indicate the presence of volcanogenic clouds in the stratosphere. This study suggests that radar is a valuable complement to traditional seismic and satellite monitoring of explosive eruptions.

Dry Valleys, Antarctica

NASA Image and Video Library

2009-11-02

The McMurdo Dry Valleys are a row of valleys west of McMurdo Sound, Antarctica. They are so named because of their extremely low humidity and lack of snow and ice cover. This image was acquired December 8, 2002 by NASA Terra spacecraft.

Effects of different cryoprotectants and freezing methods on post-thaw boar semen quality.

PubMed

Yang, Chung-Hsun; Wu, Ting-Wen; Cheng, Feng-Pang; Wang, Jiann-Hsiung; Wu, Jui-Te

2016-03-01

The current study aimed to investigate the effects of different concentrations of glycerol (0%, 1%, 2%, 3%, and 5%) and dimethylacetamide (DMA: 0%, 1%, 3%, and 5%) on post-sperm quality characteristics following semen freezing in dry ice (D) or liquid nitrogen (N). Semen was collected from Duroc boars and was allocated to 32 treatment groups for cryopreservation. Analysis of post-thaw semen quality and fertility after artificial insemination (AI) was used to examine the combinatorial effects of different treatments. The best scores for post-thaw sperm motility, sperm viability, and sperm acrosomal integrity were observed in semen frozen in: (a) dry ice in the presence of 5% glycerol and no DMA (16D-treatment); (b) dry ice in the presence of 3% glycerol and no DMA (9D-treatment); and (c) liquid nitrogen in the presence of 3% glycerol and 1% DMA (10N-treatment), with no significant difference observed among these three treatments. The farrowing rates after AI with post-thawed semen after 9D- and 10N-treatments were 33% and 50%, respectively. To summarize, the results of the present study indicated that the freezing extender containing 3% glycerol in combination with the straw-freezing method using dry ice produced the best post-thaw quality parameters of boar semen. Combinations of glycerol and DMA did not enhance the cryosurvival of boar spermatozoa. Copyright © 2016 Society for Biology of Reproduction & the Institute of Animal Reproduction and Food Research of Polish Academy of Sciences in Olsztyn. Published by Elsevier Urban & Partner Sp. z o.o. All rights reserved.

Measurements of Refractory Black Carbon (rBC) Aerosols in the McMurdo Dry Valleys, Antarctica

NASA Astrophysics Data System (ADS)

Khan, A. L.; McMeeking, G. R.; Lyons, W. B.; Schwarz, J. P.; Welch, K. A.; McKnight, D. M.

2015-12-01

Measurements of light absorbing particles in the boundary layer of the high southern latitudes are scarce. During the 2013-2014 austral summer field season refractory black carbon (rBC) aerosols were quantified by a single particle soot photometer (SP2) in the McMurdo Dry Valleys, Antarctica. The dark rBC particles absorb more radiation thereby increasing atmospheric heating, as well as reducing surface albedo and enhancing hydrologic melt when deposited on highly reflective surfaces such as snow and ice. Quantifying both local and long-range atmospheric transport of rBC to this region of a remote continent mostly covered by ice and snow would be useful in understanding meltwater generation as climate changes. Although the Dry Valleys are the largest ice-free region of Antarctica, they contain many alpine glaciers, some of which are fed from the East Antarctic Ice Sheet (EAIS). Continuous rBC measurements were collected at Lake Hoare Camp in the Taylor Valley for two months, along with shorter periods at more remote locations within the Dry Valleys. Conditions at the Lake Hoare Camp were dominated by up-valley winds from McMurdo Sound, however, winds also brought air down-valley from the EAIS polar plateau. Here we investigated periods dominated by both up and down-valley winds to explore differences in rBC concentrations, size distributions, and scattering properties. The average background rBC mass concentration was 1ng/m3, though concentrations as high as 50 ng/m3 were observed at times, likely due to local sources.

Life Detection and Characterization of Subsurface Ice and Brine in the McMurdo Dry Valleys Using an Ultrasonic Gopher: A NASA ASTEP Project

NASA Technical Reports Server (NTRS)

Doran, P. T.; Bar-Cohen, Y.; Fritsen, C.; Kenig, F.; McKay, C. P.; Murray, A.; Sherrit, S.

2003-01-01

Evidence for the presence of ice and fluids near the surface of Mars in both the distant and recent past is growing with each new mission to the Planet. One explanation for fluids forming springlike features on Mars is the discharge of subsurface brines. Brines offer potential refugia for extant Martian life, and near surface ice could preserve a record of past life on the planet. Proven techniques to get underground to sample these environments, and get below the disruptive influence of the surface oxidant and radiation regime, will be critical for future astrobiology missions to Mars. Our Astrobiology for Science and Technology for Exploring Planets (ASTEP) project has the goal to develop and test a novel ultrasonic corer in a Mars analog environment, the McMurdo Dry valleys, Antarctica, and to detect and describe life in a previously unstudied extreme ecosystem; Lake Vida (Fig. 1), an ice-sealed lake.

Paired Straight Hearth Furnace - Transformational Ironmaking Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Wei-Kao; Debski, Paul

2014-11-19

The U. S. steel industry has reduced its energy intensity per ton of steel shipped by 33% since 1990. However, further significant gains in energy efficiency will require the development of new, transformational iron and steelmaking processes. The Paired Straight Hearth Furnace (PSH) process is an emerging alternative high productivity, direct reduced iron (DRI) technology that may achieve very low fuel rates and has the potential to replace blast furnace ironmaking. The PSH furnace can operate independently or may be coupled with other melting technologies to produce liquid hot metal that is both similar to blast furnace iron and suitablemore » as a feedstock for basic oxygen steelmaking furnaces. The PSH process uses non-metallurgical coal as a reductant to convert iron oxides such as iron ore and steelmaking by-product oxides to DRI pellets. In this process, a multi-layer, nominally 120mm tall bed of composite “green balls” made from oxide, coal and binder is built up and contained within a moving refractory hearth. The pellet bed absorbs radiant heat energy during exposure to the high temperature interior refractory surfaces of the PSH while generating a strongly reducing gas atmosphere in the bed that yields a highly metalized DRI product. The PSH concept has been well tested in static hearth experiments. A moving bed design is being developed. The process developers believe that if successful, the PSH process has the potential to replace blast furnaces and coke ovens at a fraction of the operating and capital cost while using about 30% less energy relative to current blast furnace technology. DRI output could also feed electric arc furnaces (EAFs) by displacing a portion of the scrap charge.« less

Impact of aerosols on ice crystal size

NASA Astrophysics Data System (ADS)

Zhao, Bin; Liou, Kuo-Nan; Gu, Yu; Jiang, Jonathan H.; Li, Qinbin; Fu, Rong; Huang, Lei; Liu, Xiaohong; Shi, Xiangjun; Su, Hui; He, Cenlin

2018-01-01

The interactions between aerosols and ice clouds represent one of the largest uncertainties in global radiative forcing from pre-industrial time to the present. In particular, the impact of aerosols on ice crystal effective radius (Rei), which is a key parameter determining ice clouds' net radiative effect, is highly uncertain due to limited and conflicting observational evidence. Here we investigate the effects of aerosols on Rei under different meteorological conditions using 9-year satellite observations. We find that the responses of Rei to aerosol loadings are modulated by water vapor amount in conjunction with several other meteorological parameters. While there is a significant negative correlation between Rei and aerosol loading in moist conditions, consistent with the "Twomey effect" for liquid clouds, a strong positive correlation between the two occurs in dry conditions. Simulations based on a cloud parcel model suggest that water vapor modulates the relative importance of different ice nucleation modes, leading to the opposite aerosol impacts between moist and dry conditions. When ice clouds are decomposed into those generated from deep convection and formed in situ, the water vapor modulation remains in effect for both ice cloud types, although the sensitivities of Rei to aerosols differ noticeably between them due to distinct formation mechanisms. The water vapor modulation can largely explain the difference in the responses of Rei to aerosol loadings in various seasons. A proper representation of the water vapor modulation is essential for an accurate estimate of aerosol-cloud radiative forcing produced by ice clouds.

Unusual radar echoes from the Greenland ice sheet

NASA Technical Reports Server (NTRS)

Rignot, E. J.; Vanzyl, J. J.; Ostro, S. J.; Jezek, K. C.

1993-01-01

In June 1991, the NASA/Jet Propulsion Laboratory airborne synthetic-aperture radar (AIRSAR) instrument collected the first calibrated data set of multifrequency, polarimetric, radar observations of the Greenland ice sheet. At the time of the AIRSAR overflight, ground teams recorded the snow and firn (old snow) stratigraphy, grain size, density, and temperature at ice camps in three of the four snow zones identified by glaciologists to characterize four different degrees of summer melting of the Greenland ice sheet. The four snow zones are: (1) the dry-snow zone, at high elevation, where melting rarely occurs; (2) the percolation zone, where summer melting generates water that percolates down through the cold, porous, dry snow and then refreezes in place to form massive layers and pipes of solid ice; (3) the soaked-snow zone where melting saturates the snow with liquid water and forms standing lakes; and (4) the ablation zone, at the lowest elevations, where melting is vigorous enough to remove the seasonal snow cover and ablate the glacier ice. There is interest in mapping the spatial extent and temporal variability of these different snow zones repeatedly by using remote sensing techniques. The objectives of the 1991 experiment were to study changes in radar scattering properties across the different melting zones of the Greenland ice sheet, and relate the radar properties of the ice sheet to the snow and firn physical properties via relevant scattering mechanisms. Here, we present an analysis of the unusual radar echoes measured from the percolation zone.

Physico-chemical characteristics of microwave-dried wheat distillers grain with solubles.

PubMed

Mosqueda, Maria Rosario P; Tabil, Lope G; Meda, Venkatesh

2013-01-01

Laboratory-prepared samples of wheat distillers grain with solubles with varying condensed distillers solubles (CDS) content were dried under varying microwave power, and microwave convection settings using a domestic microwave oven to examine their effect on the chemical, structural, color, flow, compression, thermal, and frictional properties of the product, which is dried distillers grain with solubles (DDGS). As CDS level increased, protein and ash content increased, while fat and fiber content decreased in wheat-based DDGS. Fat content was also markedly effected by the microwave oven drying conditions. While CDS level, microwave power or microwave convection setting, and/or their interactions significantly effected a number of physical properties; results indicated that CDS level had a stronger influence compared to the other factors. DDGS samples with high CDS levels were significantly denser, finer but more differentiated in size, less flowable, and less dispersible. These also produced denser and stronger pellets.

Efficacy of dry-ice blasting in preventive maintenance of auto robotic assemblies

NASA Astrophysics Data System (ADS)

Baluch, Nazim; Mohtar, Shahimi; Abdullah, Che Sobry

2016-08-01

Welding robots are extensively applied in the automotive assemblies and `Spot Welding' is the most common welding application found in the auto stamping assembly manufacturing. Every manufacturing process is subject to variations - with resistance welding, these include; part fit up, part thickness variations, misaligned electrodes, variations in coating materials or thickness, sealers, weld force variations, shunting, machine tooling degradation; and slag and spatter damage. All welding gun tips undergo wear; an elemental part of the process. Though adaptive resistance welding control automatically compensates to keep production and quality up to the levels needed as gun tips undergo wear so that the welds remain reliable; the system cannot compensate for deterioration caused by the slag and spatter on the part holding fixtures, sensors, and gun tips. To cleanse welding robots of slag and spatter, dry-ice blasting has proven to be an effective remedy. This paper describes Spot welding process, analyses the slag and spatter formation during robotic welding of stamping assemblies, and concludes that the dry ice blasting process's utility in cleansing of welding robots in auto stamping plant operations is paramount and exigent.

Microplastics in sediments from the littoral zone of the north Tunisian coast (Mediterranean Sea)

NASA Astrophysics Data System (ADS)

Abidli, Sami; Antunes, Joana C.; Ferreira, Joana L.; Lahbib, Youssef; Sobral, Paula; Trigui El Menif, Najoua

2018-05-01

The distribution of microplastics (MPs) was investigated in the sediments of five sampling sites from the northern Tunisian coast during June 2017. MPs were categorized according to type, colour and size. Representative MPs from the five sites were isolated for polymer identification using Fourier Transformed Infrared Spectroscopy in attenuated total reflectance mode (FTIR-ATR). Results showed that MPs were recovered, from all sediment samples, indicating for the first time, their extensive distribution in Tunisian coast. Concentrations varied from 141.20 ± 25.98 to 461.25 ± 29.74 items kg-1 dry weight. Fibres, fragments, Styrofoam®, pellets and films were the types registered in this study. With the exception of Menzel Bourguiba (MB), fibres significantly outnumbered plastic particles followed by fragments, Styrofoam®, films and pellets. The predominant colours are as follows: black > clear > white > red > blue > green for fibres, blue > white > clear > red > green > yellow > black for fragments, blue > white > black > clear for films while only white pellets and Styrofoam® were found. MPs particles ranged from 0.1 to 5 mm in length. A total of three polymer types were identified, polyethylene (PE), polypropylene (PP) and polystyrene (PS). Except for industrial pellets, the presence of MPs is likely due to the degradation of marine plastic debris accumulating in each site. This work provides original data of the presence of MPs in coastal sediments from Northern Tunisian coast.

Puffing of okara/rice blends using a rice cake machine.

PubMed

Xie, M; Huff, H; Hsieh, F; Mustapha, A

2008-10-01

Okara is the insoluble byproduct of soymilk and tofu manufactures. It is cheap, high in nutrients, and possesses great potential to be applied to functional human foods. In this study, a puffed okara/rice cake product was developed with blends of okara pellets and parboiled rice. Consumer preference and acceptance tests were conducted for the product. Okara pellets were prepared by grinding the strands obtained from extruding a mixture of dried okara and rice flour (3:2, w/w) with a twin-screw extruder. Okara pellets and parboiled rice were blended in 4 ratios, 90:10, 70:30, 40:60, and 0:100 (w/w), and tempered to 14% and 17% moisture. The blends were puffed at 221, 232, and 243 degrees C for 4, 5, or 6 s. The okara/rice cakes were evaluated for specific volume (SPV), texture, color, and percent weight loss after tumbling. Overall, the decrease in okara content and increase in moisture, heating temperature and time led to greater specific volume (SPV) and hardness, lighter color, and lower percent weight loss after tumbling. The consumer tests indicated that the okara/rice cake containing 70% okara pellets was preferred and the 90% one was liked the least. The possible drivers of liking for the puffed okara/rice cakes could be the okara content, hardness, SPV, bright color, and percent weight loss after tumbling.

Controlled nucleation in freeze-drying: effects on pore size in the dried product layer, mass transfer resistance, and primary drying rate.

PubMed

Konstantinidis, Alex K; Kuu, Wei; Otten, Lori; Nail, Steven L; Sever, Robert R

2011-08-01

A novel and scalable method has been developed to enable control of the ice nucleation step for the freezing process during lyophilization. This method manipulates the chamber pressure of the freeze dryer to simultaneously induce nucleation in all product vials at a desired temperature. The effects of controlled nucleation on the drying rate of various formulations including 5% (w/w) mannitol, 5% (w/w) sucrose, and a mixture of 3% (w/w) mannitol and 2% (w/w) sucrose were studied. For a 5% (w/w) mannitol, uncontrolled ice nucleation occurred randomly at product temperatures between -8.0°C and -15.9°C as the vials were cooled to -40°C. Controlled ice nucleation was achieved at product temperatures between -2.3°C and -3.7°C. The effect of nucleation control on the effective pore radius (r(e) ) of the cake was determined from the product temperature profiles using a pore diffusion model in combination with a nonlinear parameter estimation approach reported earlier. Results show that the value of r(e) for 5% (w/w) mannitol was enlarged from 13 to 27 μm by uniformly inducing nucleation at higher temperatures. Applying the resistance parameters obtained from the pore diffusion model for 5% (w/w) mannitol, optimized cycles were theoretically generated and experimentally tested, resulting in a 41% reduction in primary drying time. Copyright © 2011 Wiley-Liss, Inc.

Passive infrared ice detection for helicopter applications

NASA Technical Reports Server (NTRS)

Dershowitz, Adam L.; Hansman, R. John, Jr.

1990-01-01

A technique is proposed to remotely detect rotor icing on helicopters by using passive IR thermometry to detect the warming caused by latent heat release as supercooled water freezes. During icing, the ice accretion region will be warmer than the uniced trailing edge, resulting in a characteristic chordwise temperature profile. Preliminary tests were conducted on a static model in the NASA Icing Research Tunnel for a variety of wet (glaze) and dry (rime) ice conditions. The chordwise temperature profiles were confirmed by observation with an IR thermal video system and thermocouple observations. The IR observations were consistent with predictions of the LEWICE ice accretion code, which was used to extrapolate the observations to rotor icing conditions. Based on the static observations, the passive IR ice detection technique appears promising; however, further testing or rotating blades is required.

Investigation on the Characteristics of Pellet Ablation in a Toroidal Plasma

NASA Astrophysics Data System (ADS)

Sato, K. N.; Sakakita, H.; Fujita, H.

2003-06-01

Characteristics of a cloud ablated from an ice pellet has been investigated in detail in the JIPP T-IIU tokamak plasma by utilizing a new scheme of pellet injection system, "the injection-angle controllable system". A long "helical tail" of ablation light has been observed using CCD cameras and a high speed framing photograph in the case of on-axis and off-axis injection with the injection angle smaller than a certain value. The direction of the helical tail is found to be independent to that of the total magnetic field lines of the torus. From the experiments with the combination of two toroildal filed directions and two plasma current directions, it is considered that the tail seems to rotate, in most cases, to the electron diamagnetic direction poloidally, and to the opposite to the plasma current direction toroidally. Consideration on various cross sections including charge exchange, ionization and elastic collisions leads us to the conclusion that the tail-shaped phenomena may come from the situation of charge exchange equilibrium of hydrogen ions and neutrals at extremely high density regime in the cloud. The relation of ablation behavior with plasma potential and rotation has also been studied. Potential measurements of pellet-injected plasmas using heavy ion beam probe (HIBP) method were carried out for the first time. In the case of an injection angle to be anti-parallel to the electron diamagnetic direction in the poloidal plane, the result shows that the direction of potential change is negative, and consequently the potential after the injection should be negative because it has been measured to be negative in usual ohmic plasmas without pellet injection. Thus, the direction of the "tail" structure seems to be consistent to that of the plasma potential measured, if it is considered that tail structure may be caused by the effect of the plasma potential and the rotation.

Space Food

NASA Technical Reports Server (NTRS)

1994-01-01

In planning for the long duration Apollo missions, NASA conducted extensive research into space food. One of the techniques developed was freeze drying. Action Products commercialized this technique, concentrating on snack food including the first freeze-dried ice cream. The foods are cooked, quickly frozen and then slowly heated in a vacuum chamber to remove the ice crystals formed by the freezing process. The final product retains 98 percent of its nutrition and weighs only 20 percent of its original weight. Action snacks are sold at museums, NASA facilities and are exported to a number of foreign countries. Sales run to several million dollars annually.

Effects of irradiation of feed ingredients added to meal or pelleted diets on growth performance of weanling pigs.

PubMed

Groesbeck, C N; Derouchey, J M; Tokach, M D; Goodband, R D; Dritz, S S; Nelssen, J L

2009-12-01

Two experiments were conducted to evaluate the effects of irradiated ingredients in meal and pelleted diets on nursery pig performance. In Exp. 1, a total of 192 pigs (initial BW, 6.0 kg) were used in a 25-d experiment. Pigs were blocked by BW and randomly allotted in a 2 x 2 factorial arrangement of treatments with main effects of diet form (meal or pellet) and either irradiated (11.92 kGy) or nonirradiated spray-dried animal plasma (SDAP). Irradiated SDAP had less total bacterial amounts than nonirradiated SDAP, and pelleted diets also had less bacterial amounts than diets in meal form. However, the complete diets with and without irradiated SDAP had similar bacterial concentrations. There was a diet form x SDAP irradiation interaction (P < 0.05) for ADG from d 0 to 11 and d 0 to 25. Pigs fed irradiated SDAP in meal form had increased ADG compared with pigs fed the nonirradiated meal diet, with no change in ADG of pigs fed pelleted diets. In addition, from d 0 to 11, pigs fed irradiated SDAP or pelleted diets had greater G:F (P < 0.01) compared with pigs fed regular SDAP and meal diets, respectively. In Exp. 2, a total of 350 pigs (initial BW, 4.9 kg) were used in a 22-d experiment to determine the effects of feeding irradiated protein sources (SDAP, soybean meal, fish meal, or all 3) in meal and pellet diets on pig performance. Pigs were blocked by BW and randomly allotted to 1 of 10 treatments consisting of a single diet formulation fed in either meal or pellet form containing either no irradiated protein sources or irradiated SDAP, soybean meal, fish meal, or all 3 irradiated protein sources (10.20 kGy). Irradiated SDAP, soybean meal, and fish meal tended to have reduced total bacterial concentrations compared with nonirradiated plasma, and pelleted diets had reduced bacterial concentrations compared with diets in meal form. No irradiation x diet form interactions (P > 0.16) were observed. From d 0 to 11, pigs fed diets containing irradiated protein sources had greater (P < 0.03) G:F compared with pigs fed the control diets, with no difference in ADG or ADFI. From d 0 to 11, and overall (d 0 to 22), pigs fed pellet diets had greater G:F (P < 0.01) compared with pigs fed meal diets, with no difference in ADG and ADFI. These studies indicate that both irradiation and pelleting are manufacturing processes that can reduce bacteria concentrations in feed ingredients and diets. Irradiated SDAP, soybean meal, and fish meal improved G:F compared with control diets containing nonirradiated ingredients. Furthermore, pigs fed pelleted diets had increased G:F compared with pigs fed meal diets.

Chemo-Mechanical Characteristics of Mud Formed from Environmental Dust Particles in Humid Ambient Air

PubMed Central

Hassan, Ghassan; Yilbas, B. S.; Said, Syed A. M.; Al-Aqeeli, N.; Matin, Asif

2016-01-01

Mud formed from environmental dust particles in humid ambient air significantly influences the performance of solar harvesting devices. This study examines the characterization of environmental dust particles and the chemo-mechanics of dry mud formed from dust particles. Analytical tools, including scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, particle sizing, and X-ray diffraction, are used to characterize dry mud and dust particles. A micro/nano tribometer is used to measure the tangential force and friction coefficient while tensile tests are carried out to assess the binding forces of dry mud pellets. After dry mud is removed, mud residuals on the glass surface are examined and the optical transmittance of the glass is measured. Dust particles include alkaline compounds, which dissolve in water condensate and form a mud solution with high pH (pH = 7.5). The mud solution forms a thin liquid film at the interface of dust particles and surface. Crystals form as the mud solution dries, thus, increasing the adhesion work required to remove dry mud from the surface. Optical transmittance of the glass is reduced after dry mud is removed due to the dry mud residue on the surface. PMID:27445272

Chemo-Mechanical Characteristics of Mud Formed from Environmental Dust Particles in Humid Ambient Air.

PubMed

Hassan, Ghassan; Yilbas, B S; Said, Syed A M; Al-Aqeeli, N; Matin, Asif

2016-07-22

Mud formed from environmental dust particles in humid ambient air significantly influences the performance of solar harvesting devices. This study examines the characterization of environmental dust particles and the chemo-mechanics of dry mud formed from dust particles. Analytical tools, including scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, particle sizing, and X-ray diffraction, are used to characterize dry mud and dust particles. A micro/nano tribometer is used to measure the tangential force and friction coefficient while tensile tests are carried out to assess the binding forces of dry mud pellets. After dry mud is removed, mud residuals on the glass surface are examined and the optical transmittance of the glass is measured. Dust particles include alkaline compounds, which dissolve in water condensate and form a mud solution with high pH (pH = 7.5). The mud solution forms a thin liquid film at the interface of dust particles and surface. Crystals form as the mud solution dries, thus, increasing the adhesion work required to remove dry mud from the surface. Optical transmittance of the glass is reduced after dry mud is removed due to the dry mud residue on the surface.

Perennial Antarctic lake ice: an oasis for life in a polar desert

NASA Technical Reports Server (NTRS)

Priscu, J. C.; Fritsen, C. H.; Adams, E. E.; Giovannoni, S. J.; Paerl, H. W.; McKay, C. P.; Doran, P. T.; Gordon, D. A.; Lanoil, B. D.; Pinckney, J. L.

1998-01-01

The permanent ice covers of Antarctic lakes in the McMurdo Dry Valleys develop liquid water inclusions in response to solar heating of internal aeolian-derived sediments. The ice sediment particles serve as nutrient (inorganic and organic)-enriched microzones for the establishment of a physiologically and ecologically complex microbial consortium capable of contemporaneous photosynthesis, nitrogen fixation, and decomposition. The consortium is capable of physically and chemically establishing and modifying a relatively nutrient- and organic matter-enriched microbial "oasis" embedded in the lake ice cover.

Perennial Antarctic lake ice: an oasis for life in a polar desert.

PubMed

Priscu, J C; Fritsen, C H; Adams, E E; Giovannoni, S J; Paerl, H W; McKay, C P; Doran, P T; Gordon, D A; Lanoil, B D; Pinckney, J L

1998-06-26

The permanent ice covers of Antarctic lakes in the McMurdo Dry Valleys develop liquid water inclusions in response to solar heating of internal aeolian-derived sediments. The ice sediment particles serve as nutrient (inorganic and organic)-enriched microzones for the establishment of a physiologically and ecologically complex microbial consortium capable of contemporaneous photosynthesis, nitrogen fixation, and decomposition. The consortium is capable of physically and chemically establishing and modifying a relatively nutrient- and organic matter-enriched microbial "oasis" embedded in the lake ice cover.

Formation of highly porous aerosol particles by atmospheric freeze-drying in ice clouds

PubMed Central

Adler, Gabriela; Koop, Thomas; Haspel, Carynelisa; Taraniuk, Ilya; Moise, Tamar; Koren, Ilan; Heiblum, Reuven H.; Rudich, Yinon

2013-01-01

The cycling of atmospheric aerosols through clouds can change their chemical and physical properties and thus modify how aerosols affect cloud microphysics and, subsequently, precipitation and climate. Current knowledge about aerosol processing by clouds is rather limited to chemical reactions within water droplets in warm low-altitude clouds. However, in cold high-altitude cirrus clouds and anvils of high convective clouds in the tropics and midlatitudes, humidified aerosols freeze to form ice, which upon exposure to subsaturation conditions with respect to ice can sublimate, leaving behind residual modified aerosols. This freeze-drying process can occur in various types of clouds. Here we simulate an atmospheric freeze-drying cycle of aerosols in laboratory experiments using proxies for atmospheric aerosols. We find that aerosols that contain organic material that undergo such a process can form highly porous aerosol particles with a larger diameter and a lower density than the initial homogeneous aerosol. We attribute this morphology change to phase separation upon freezing followed by a glass transition of the organic material that can preserve a porous structure after ice sublimation. A porous structure may explain the previously observed enhancement in ice nucleation efficiency of glassy organic particles. We find that highly porous aerosol particles scatter solar light less efficiently than nonporous aerosol particles. Using a combination of satellite and radiosonde data, we show that highly porous aerosol formation can readily occur in highly convective clouds, which are widespread in the tropics and midlatitudes. These observations may have implications for subsequent cloud formation cycles and aerosol albedo near cloud edges. PMID:24297908

Formation of highly porous aerosol particles by atmospheric freeze-drying in ice clouds.

PubMed

Adler, Gabriela; Koop, Thomas; Haspel, Carynelisa; Taraniuk, Ilya; Moise, Tamar; Koren, Ilan; Heiblum, Reuven H; Rudich, Yinon

2013-12-17

The cycling of atmospheric aerosols through clouds can change their chemical and physical properties and thus modify how aerosols affect cloud microphysics and, subsequently, precipitation and climate. Current knowledge about aerosol processing by clouds is rather limited to chemical reactions within water droplets in warm low-altitude clouds. However, in cold high-altitude cirrus clouds and anvils of high convective clouds in the tropics and midlatitudes, humidified aerosols freeze to form ice, which upon exposure to subsaturation conditions with respect to ice can sublimate, leaving behind residual modified aerosols. This freeze-drying process can occur in various types of clouds. Here we simulate an atmospheric freeze-drying cycle of aerosols in laboratory experiments using proxies for atmospheric aerosols. We find that aerosols that contain organic material that undergo such a process can form highly porous aerosol particles with a larger diameter and a lower density than the initial homogeneous aerosol. We attribute this morphology change to phase separation upon freezing followed by a glass transition of the organic material that can preserve a porous structure after ice sublimation. A porous structure may explain the previously observed enhancement in ice nucleation efficiency of glassy organic particles. We find that highly porous aerosol particles scatter solar light less efficiently than nonporous aerosol particles. Using a combination of satellite and radiosonde data, we show that highly porous aerosol formation can readily occur in highly convective clouds, which are widespread in the tropics and midlatitudes. These observations may have implications for subsequent cloud formation cycles and aerosol albedo near cloud edges.

Effects of thermal pretreatment and catalyst on biomass gasification efficiency and syngas composition

DOE PAGES

Cheah, Singfoong; Jablonski, Whitney S.; Olstad, Jessica L.; ...

2016-09-16

This work explores the combined effects of thermal pretreatment and using a catalyst in situ on gasification carbon conversion efficiency, as well as product gas and tar content and compositions. To compare the effects of thermal pretreatment, pelletized and ground oak with three different levels of thermal pretreatment were gasified in a fluidized bed reactor. The pretreatments applied to the oak were (1) pelletization, (2) drying at 180 °C in air, and (3) torrefaction at 270 °C in nitrogen. The oak dried at 180 °C produced syngas of similar quality and approximately the same amount of char as untreated oak.more » Torrefaction at 270 °C resulted in syngas with a higher hydrogen to CO ratio, lower methane, and less than half of the total tar -- all of which are desirable properties in terms of product gas quality. However, the oak torrefied at 270 °C also produced more than two times the amount of char as the untreated, pelletized oak. To determine the effect of catalyst, a series of experiments were conducted using olivine impregnated with nickel and cerium as the fluidized bed material in the gasifier. These tests showed that modified olivine can improve hydrogen production and reduce methane and tar levels in the syngas. The result was observed for both treated and untreated oak; although the effect was more substantial for untreated oak, for which the use of modified olivine reduced tar concentrations in the product gas by 60%, with a larger reduction in heavier tars than lighter tars. Furthermore, this result is important because reduction in heavier tar plays a more important role in benefitting downstream operations.« less

Ice-Templated Bimodal-Porous Silver Nanowire/PDMS Nanocomposites for Stretchable Conductor.

PubMed

Oh, Jae Young; Lee, Dongju; Hong, Soon Hyung

2018-06-27

A three-dimensional (3D) bimodal-porous silver nanowire (AgNW) nanostructure with superior electrical properties is fabricated by freeze drying of AgNW aqueous dispersion with macrosized ice spheres for bimodal-porous structure. The ice sphere dispersed AgNW solution yields a 3D AgNW network at the surface of ice sphere and formation of macropores by removal of ice sphere during freeze-drying process. The resulting nanostructures exhibit excellent electrical properties due to their low electrical percolation threshold by the formation of macropores, which results in an efficient and dense 3D AgNW network with a small amount of AgNWs. The highly conductive and stretchable AgNW/poly(dimethylsiloxane) (PDMS) nanocomposites are made by impregnating the 3D porous conductive network with highly stretchable poly(dimethylsiloxane) (PDMS) matrix. The AgNW/PDMS nanocomposites exhibit a high conductivity of 42 S/cm with addition of relatively small amount of 2 wt %. The high conductivity is retained when stretched up to 120% elongation even after 100 stretching-releasing cycles. Due to high electrical conductivity and superior stretchability of AgNW/PDMS nanocomposites, these are expected to be used in stretchable electronic devices.

Passive anti-frosting surfaces using microscopic ice arrays

NASA Astrophysics Data System (ADS)

Ahmadi, Farzad; Nath, Saurabh; Iliff, Grady; Boreyko, Jonathan

2017-11-01

Despite exceptional advances in surface chemistry and micro/nanofabrication, no engineered surface has been able to passively suppress the in-plane growth of frost occurring in humid, subfreezing environments. Motivated by this, and inspired by the fact that ice itself can evaporate nearby liquid water droplets, we present a passive anti-frosting surface in which the majority of the surface remains dry indefinitely. We fabricated an aluminum surface exhibiting an array of small metallic fins, where a wicking micro-groove was laser-cut along the top of each fin to produce elevated water ``stripes'' that freeze into ice. As the saturation vapor pressure of ice is less than that of supercooled liquid water, the ice stripes serve as overlapping humidity sinks that siphon all nearby moisture from the air and prevent condensation and frost from forming anywhere else on the surface. Our experimental results show that regions between stripes remain dry even after 24 hours of operation under humid and supercooled conditions. We believe that the presented anti-frosting technology has the potential to help solve the world's multi-billion dollar frosting problem that adversely affects transportation, power generation, and HVAC systems.

Spatial Variability of Climate Signatures Recorded in an Array of Shallow Firn Cores from the Western Greenland Percolation Zone

NASA Astrophysics Data System (ADS)

Thundercloud, Z. R.; Osterberg, E. C.; Ferris, D. G.; Graeter, K.; Lewis, G.; Hawley, R. L.; Marshall, H. P.

2016-12-01

Greenland ice cores provide seasonally to annually resolved proxy records of past temperature, accumulation and atmospheric circulation. Most Greenland ice cores have been collected from the dry snow zone at elevations greater than 2500 m to produce records of North Atlantic paleoclimate over the last full glacial cycle. Ice cores collected from more costal regions, however, provide the opportunity to develop regional-scale records of climate conditions along ice sheet margins where recent temperature and precipitation changes have been larger than those in the ice sheet interior. These cores are more readily comparable to lake sediment and landscape (i.e. moraine) records from the ice sheet margin, and are potentially more sensitive to sea-ice variability due to the proximity to the coast. Here we present major ion and stable isotope records from an array of firn cores (40-55 year records) collected in the western Greenland percolation zone, and assess the spatial variability of ice core statistical relationships with the North Atlantic Oscillation (NAO) and Baffin Bay sea ice extent. Seven cores were collected from elevations of 2100-2500 m along a 400-km segment of the ice sheet from Dye-2 to Milcent as part of the Greenland Traverse for Accumulation and Climate Studies (GreenTrACS) project from May-June 2016. They were sampled by a continuous melter system at Dartmouth College, and analyzed using Dionex ion chromatographs and a Picarro L2130-i laser ring-down spectrometer. We focus on the signature of the NAO and Baffin Bay sea ice extent in the sea-salt, dust, deuterium excess (d-excess), and methanesulfonic acid (MSA) firn core records, and assess the special variability of these climate-ice core relationships across the study area. Climate reanalysis data indicate that NAO-ice core correlations should be stronger at lower elevation in the percolation zone than high in the dry snow zone. Our results will provide valuable insight into the sensitivity of Greenland ice core paleoclimate reconstructions to the specific ice core location, and thereby aid in site selection for deeper ice cores that could span the Holocene.

Standard for Ground Vehicle Mobility

DTIC Science & Technology

2005-02-01

Zone Dry climates (2), humid mesothermal (3), See Appendix A humid microthermal (4), undifferentiated highland (6) Condition Dry, wet, snow See...represent the Dry, the Humid Mesothermal, and the Humid Microthermal climate zones, respectively. Scenarios ERDC-GSL was sponsored by WARSIM to...Coast D. Humid Microthermal Climates Humid Continental, Warm Summer, Humid Continental, Cool Summer, Sub-Arctic E. Polar Climates Tundra, Ice Caps F

Niche specialization of bacteria in permanently ice-covered lakes of the McMurdo Dry Valleys, Antarctica.

PubMed

Kwon, Miye; Kim, Mincheol; Takacs-Vesbach, Cristina; Lee, Jaejin; Hong, Soon Gyu; Kim, Sang Jong; Priscu, John C; Kim, Ok-Sun

2017-06-01

Perennially ice-covered lakes in the McMurdo Dry Valleys, Antarctica, are chemically stratified with depth and have distinct biological gradients. Despite long-term research on these unique environments, data on the structure of the microbial communities in the water columns of these lakes are scarce. Here, we examined bacterial diversity in five ice-covered Antarctic lakes by 16S rRNA gene-based pyrosequencing. Distinct communities were present in each lake, reflecting the unique biogeochemical characteristics of these environments. Further, certain bacterial lineages were confined exclusively to specific depths within each lake. For example, candidate division WM88 occurred solely at a depth of 15 m in Lake Fryxell, whereas unknown lineages of Chlorobi were found only at a depth of 18 m in Lake Miers, and two distinct classes of Firmicutes inhabited East and West Lobe Bonney at depths of 30 m. Redundancy analysis revealed that community variation of bacterioplankton could be explained by the distinct conditions of each lake and depth; in particular, assemblages from layers beneath the chemocline had biogeochemical associations that differed from those in the upper layers. These patterns of community composition may represent bacterial adaptations to the extreme and unique biogeochemical gradients of ice-covered lakes in the McMurdo Dry Valleys. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

The McMurdo Dry Valleys: A landscape on the threshold of change

NASA Astrophysics Data System (ADS)

Fountain, Andrew G.; Levy, Joseph S.; Gooseff, Michael N.; Van Horn, David

2014-11-01

Field observations of coastal and lowland regions in the McMurdo Dry Valleys suggest they are on the threshold of rapid topographic change, in contrast to the high elevation upland landscape that represents some of the lowest rates of surface change on Earth. A number of landscapes have undergone dramatic and unprecedented landscape changes over the past decade including, the Wright Lower Glacier (Wright Valley) - ablated several tens of meters, the Garwood River (Garwood Valley) has incised > 3 m into massive ice permafrost, smaller streams in Taylor Valley (Crescent, Lawson, and Lost Seal Streams) have experienced extensive down-cutting and/or bank undercutting, and Canada Glacier (Taylor Valley) has formed sheer, > 4 meter deep canyons. The commonality between all these landscape changes appears to be sediment on ice acting as a catalyst for melting, including ice-cement permafrost thaw. We attribute these changes to increasing solar radiation over the past decade despite no significant trend in summer air temperature. To infer possible future landscape changes in the McMurdo Dry Valleys, due to anticipated climate warming, we map ‘at risk’ landscapes defined as those with buried massive ice in relative warm regions of the valleys. Results show that large regions of the valley bottoms are ‘at risk’. Changes in surface topography will trigger important responses in hydrology, geochemistry, and biological community structure and function.

Inland diatoms from the McMurdo Dry Valleys and James Ross Island, Antarctica

USGS Publications Warehouse

Esposito, R.M.M.; Spaulding, S.A.; McKnight, Diane M.; Van De Vijver, B.; Kopalova, K.; Lubinski, D.; Hall, B.; Whittaker, T.

2008-01-01

Diatom taxa present in the inland streams and lakes of the McMurdo Dry Valleys and James Ross Island, Antarctica, are presented in this paper. A total of nine taxa are illustrated, with descriptions of four new species (Luticola austroatlantica sp. nov., Luticola dolia sp. nov., Luticola laeta sp. nov., Muelleria supra sp. nov.). In the perennially ice-covered lakes of the McMurdo Dry Valleys, diatoms are confined to benthic mats within the photic zone. In streams, diatoms are attached to benthic surfaces and within the microbial mat matrix. One species, L. austroatlantica, is found on James Ross Island, of the southern Atlantic archipelago, and the McMurdo Dry Valleys. The McMurdo Dry Valley populations are at the lower range of the size spectrum for the species. Streams flow for 6-10 weeks during the austral summer, when temperatures and solar radiation allow glacial ice to melt. The diatom flora of the region is characterized by species assemblages favored under harsh conditions, with naviculoid taxa as the dominant group and several major diatom groups conspicuously absent. ?? 2008 NRC.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

A sample of ALM became available for testing in October, 1996. The sample was in pelleted form and contained 24.2% crude protein and a gross energy content of 4102 kcal/kg (as fed basis). To determine available energy, the true metabolizable energy assay as developed by Sibbald. The T.M.E. system of feed evaluation, A.R.C. No. 83-1, Research Branch, Ottawa, Canada, was used with some modifications as described below. As the ALM was in pellets too large to feed, the ALM pellets were crumbled or finely reground for the test. Young turkeys (6 wks of age, Nicholas females) were placed in individualmore » cages and allowed to acclimate for 5 days. The turkeys weighed 2.4 kg. The turkeys were fasted for 40 hrs and precision fed 36 g of either crumbled (C) or finely (F) reground ALM. Due to the larger volume of the fine ground ALM, a smaller portion was fed and averaged 28 g. The control turkeys received an equivalent amount of glucose. There were 6 replicates for each ALM source and control turkeys. Excreta was collected for 60 hrs after feeding, consistent with recommendations for a longer collection period for fibrous materials. After the collection period ended, the excreta was quantitatively collected and all material was freeze dried. Each sample was allowed to reach equilibrium with atmospheric conditions and then weighed. The excreta was finely ground and analyzed for moisture, protein and gross energy. Samples of the fed ALM were treated in a similar manner. The true metabolizable energy content (nitrogen corrected) of the C and F ALM was 10 12 (SE 50) and 1578 (SE 159) kcal/kg, respectively. Form of ALM significantly affected TME value (P<.01). The difference in TMEn due to form was most likely due to the difference in amount fed. The crumbled form of ALM allowed the full amount to be fed and could have changed passage rate of the ALM through the digestive tract. When the TMEn of the F ALM is adjusted for dry matter content, the value is 1679 kcal/kg dry matter.« less

Injectable self inflating hydrogel pellet expanders for the treatment of orbital volume deficiency in congenital microphthalmos: preliminary results with a new therapeutic approach

PubMed Central

Schittkowski, M P; Guthoff, R F

2006-01-01

Background/aim Children with congenital microphthalmos are usually able to wear an eye prosthesis but the cosmetic aspect is determined by the size of the orbital volume deficiency. Instead of using a ball shaped standard hydrogel expander or a regular orbital implant, which would necessitate enucleation of the microphthalmic eye, this study investigates the feasibility of volume augmentation with injectable pellet expanders, as formerly suggested for acquired anophthalmos in adults only. Method The pellet expander is made from a self inflating hydrogel that takes up water by osmosis (dry state: length 8 mm, diameter 2 mm, volume 0.025 ml; in vitro hydrated state after around 1 day: length 15 mm, diameter 4 mm, volume 0.24 ml; swelling capacity: 9.6‐fold). This report concerns six patients (two girls and four boys) aged between 4 months and 42 months with unilateral microphthalmos who were treated by injection of 4–14 pellet expanders into the retrobulbar orbital tissue. Volume augmentation was 1–3.5 ml. The pellets were injected using a customised trocar and placed behind the microphthalmos directed into the intraconal space. Results The increasing orbital volume was noticeable within 2 days and was confirmed by ultrasonography and magnetic resonance imaging. The final result can be anticipated by the volume augmentation effect produced by the amount of saline solution injected in the orbital apex region. All patients were fitted with an artificial eye, which was subsequently enlarged every 3–5 months. Anophthalmic enophthalmos was fully compensated with this technique. No complications have been encountered to date. Conclusions Orbital volume augmentation with injectable self inflating hydrogel expander pellets is apparently a safe, quick, and minimally invasive technique for various indications in orbital reconstructive surgery—for example, to treat an enophthalmic appearance in microphthalmos and congenital or acquired anophthalmos. PMID:16707526

Exposed water ice discovered near the south pole of Mars

USGS Publications Warehouse

Titus, T.N.; Kieffer, H.H.; Christensen, P.R.

2003-01-01

The Mars Odyssey Thermal Emission Imaging System (THEMIS) has discovered water ice exposed near the edge of Mars' southern perennial polar cap. The surface H2O ice was first observed by THEMIS as a region that was cooler than expected for dry soil at that latitude during the summer season. Diurnal and seasonal temperature trends derived from Mars Global Surveyor Thermal Emission Spectrometer observations indicate that there is H2O ice at the surface. Viking observations, and the few other relevant THEMIS observations, indicate that surface H2O ice may be widespread around and under the perennial CO2 cap.

Antarctic lakes (above and beneath the ice sheet): Analogues for Mars

NASA Technical Reports Server (NTRS)

Rice, J. W., Jr.

1992-01-01

The perennial ice covered lakes of the Antarctic are considered to be excellent analogues to lakes that once existed on Mars. Field studies of ice covered lakes, paleolakes, and polar beaches were conducted in the Bunger Hills Oasis, Eastern Antarctica. These studies are extended to the Dry Valleys, Western Antarctica, and the Arctic. Important distinctions were made between ice covered and non-ice covered bodies of water in terms of the geomorphic signatures produced. The most notable landforms produced by ice covered lakes are ice shoved ridges. These features form discrete segmented ramparts of boulders and sediments pushed up along the shores of lakes and/or seas. Sub-ice lakes have been discovered under the Antarctic ice sheet using radio echo sounding. These lakes occur in regions of low surface slope, low surface accumulations, and low ice velocity, and occupy bedrock hollows. The presence of sub-ice lakes below the Martian polar caps is possible. The discovery of the Antarctic sub-ice lakes raises possibilities concerning Martian lakes and exobiology.

Thickness of ice on perennially frozen lakes

USGS Publications Warehouse

McKay, C.P.; Clow, G.D.; Wharton, R.A.; Squyres, S. W.

1985-01-01

The dry valleys of southern Victoria Land, constituting the largest ice-free expanse in the Antarctic, contain numerous lakes whose perennial ice cover is the cause of some unique physical and biological properties 1-3. Although the depth, temperature and salinity of the liquid water varies considerably from lake to lake, the thickness of the ice cover is remarkably consistent1, ranging from 3.5 to 6m, which is determined primarily by the balance between conduction of energy out of the ice and the release of latent heat at the ice-water interface and is also affected by the transmission and absorption of sunlight. In the steady state, the release of latent heat at the ice bottom is controlled by ablation from the ice surface. Here we present a simple energy-balance model, using the measured ablation rate of 30 cm yr-1, which can explain the observed ice thickness. ?? 1985 Nature Publishing Group.

A century of Amazon burning driven by Atlantic climate

NASA Astrophysics Data System (ADS)

Makou, M.; Thompson, L. G.; Davis, M. E.; Eglinton, T. I.

2011-12-01

Very little is known about annual burning trends in the Amazon Basin prior to remote sensing of fires beginning in the late 1970's. Fires reduce Amazon forest biomass and species richness, release pollutant aerosols, and impact the carbon cycle, compelling further investigation of fire-climate dynamics. We measured organic compounds derived from vegetation burning in ice core samples from the Quelccaya Ice Cap in Peru at better than annual resolution to reconstruct wet and dry season burning throughout the Twentieth Century. Variations in the abundance of methyl hexadecanoate, which is produced by thermal alteration of vascular plant alkanoic acids, were used as a proxy for past fire activity. Concentrations of this compound in Quelccaya ice varied strongly on seasonal, interannual, and decadal time scales over the last 100 years, with high-amplitude dry season variability and muted, decadal-scale changes in wet season fire activity. Decade-long periods of repeatedly enhanced burning occurred during the 1930's and 1960's when dry season precipitation was perpetually reduced, as evidenced by low stages of the Rio Negro. These decadal trends suggest that changes in dry season precipitation drive fire activity in the western Amazon and highlight the potential of Amazon forests to undergo repeated strong burning. Fires occurred during years when sea surface temperatures (SSTs) in the north tropical Atlantic were elevated and the north-south tropical Atlantic SST gradient was enhanced; this SST pattern likely displaced the intertropical convergence zone northward, driving subsidence and drought in the western and southern Amazon basin. Thus, our novel ice core record suggests that Amazon forest fire activity during the Twentieth Century was driven primarily by Atlantic climate processes, and future forest health will depend heavily on the evolution of tropical climate.

A preliminary study on the reduction of limonite ore by using rice husk as a reducing agent

NASA Astrophysics Data System (ADS)

Maksum, Ahmad; Husein, Michael Kelvin E.; Permana, Sulaksana; Rustandi, Andi; Wahyuadi Soedarsono, Johny

2018-03-01

The abundant of rice husk in Indonesia has encouraged researchers to study the feasibility of rice husk for substituting material that is more expensive or dangerous. In previous study, silica with a purity of 99.9% has been obtained from rice husk with calcinations process. Nevertheless, the gases resulting from the process were not used and left useless. Therefore, in this study, those gases derived from rice husk calcinations process were used as reducing agents during the ferronickel (Fe-Ni) production through a direct reduction process. The objective of this study was to investigate the effect of the amount of rice husk in the pellets on the increase of nickel content in the limonite reduction process. The limonite ore were crushed to the size of less than 150 mesh using disc-mill, and then were mixed with rice husk powder (10, 20, 30 in wt % mass) before being pelletized using bentonite as a binder. The resulted pellets were roasted at 500°C for 60 minutes and then quenched in water media. After drying process, the reduction process of 40g pellets was conducted at 1000°C for 90 minutes with 20g rice husk in furnace. The effects of additional rice husk on the direct reduction of limonite ore pellets were qualitatively analyzed by using X-ray powder diffraction (XRD) and quantitatively by Atomic absorption spectroscopy (AAS). Both analysis results showed that the reduction process followed the reaction scheme: Fe2O3→Fe3O4→FeO and NiO phase was detected in the sample with 20% rice husk addition. The optimum concentration of Ni 1.23% was obtained for 20% rice husk addition.

Source apportionment of settleable particles in an impacted urban and industrialized region in Brazil.

PubMed

Santos, Jane Meri; Reis, Neyval Costa; Galvão, Elson Silva; Silveira, Alexsander; Goulart, Elisa Valentim; Lima, Ana Teresa

2017-09-01

Settleable particulate matter (SPM), especially coarser particles with diameters greater than 10 μm, has been found culprit of high deposition rates in cities affected by hinterland industrial activities. This is the case of Metropolitan Region of Vitoria (MRV), Espirito Santo, Brazil where industrial facilities are located within the urban sprawl and building constructions are intense. Frequent population complaints to the environmental protection agency (IEMA) throughout the years have triggered monitoring campaigns to determine SPM deposition rates and source apportionment. Eight different locations were monitored throughout the MRV, and SPM was quantified and chemically characterized. Sources profiles were defined either by using US EPA SPECIATE data or by experimental analysis. Atmospheric fallout in the MRV ranged between 2 and 20g/(m 2 30-day), with only one monitoring station ranging from 6-10 g/(m 2 30-day). EC, OC, Fe, Al, and Si were found the main constituents of dry deposition in the region. Source apportionment by the chemical mass balance (CMB) model determined that steel and iron ore pelletizing industries were the main contributor to one of the eight locations whereas resuspension, civil construction, and vehicular sources were also very important contributors to the other stations. Quarries and soil were also considered expressive SPM sources, but at the city periphery. CMB model could differentiate contributions from six industrial source groups: thermoelectric; iron ore, pellet, and pellet furnaces; coal coke and coke oven; sintering, blast furnace, and basic oxygen furnace; and soil, resuspension, and vehicles. However, the CMB model was unable to differentiate between iron ore and pellet stockpiles which are present in both steel and iron ore pelletizing industries. Further characterization of source and SPM might be necessary to aid local authorities in decision-making regarding these two industrial sources.

Albedo Drop on the Greenland Ice Sheet: Relative Impacts of Wet and Dry Snow Processes

NASA Astrophysics Data System (ADS)

Chen, J.; Polashenski, C.

2014-12-01

The energy balance of the Greenland Ice Sheet (GIS) is strongly impacted by changes in snow albedo. MODIS (Moderate Resolution Imaging Spectroradiometer) observations indicate that the GIS albedo has dropped since the early part of this century. We analyze data from the MODIS products MOD10A1 for broadband snow albedo and MOD09A1 for surface spectral reflectance since 2001 to better explain the physical mechanisms driving these changes. The MODIS products are filtered, and the data is masked using microwave-derived surface melt maps to isolate albedo changes due to dry snow processes from those driven by melt impacts. Results show that the majority of recent changes in the GIS albedo - even at high elevations - are driven by snow wetting rather than dry snow processes such as grain metamorphosis and aerosol impurity deposition. The spectral signature of the smaller changes occurring within dry snow areas suggests that grain metamorphosis dominates the albedo decline in these regions.

Nearing the cold-arid limits of microbial life in permafrost of an upper dry valley, Antarctica.

PubMed

Goordial, Jacqueline; Davila, Alfonso; Lacelle, Denis; Pollard, Wayne; Marinova, Margarita M; Greer, Charles W; DiRuggiero, Jocelyn; McKay, Christopher P; Whyte, Lyle G

2016-07-01

Some of the coldest and driest permafrost soils on Earth are located in the high-elevation McMurdo Dry Valleys (MDVs) of Antarctica, but little is known about the permafrost microbial communities other than that microorganisms are present in these valleys. Here, we describe the microbiology and habitable conditions of highly unique dry and ice-cemented permafrost in University Valley, one of the coldest and driest regions in the MDVs (1700 m above sea level; mean temperature -23 °C; no degree days above freezing), where the ice in permafrost originates from vapour deposition rather than liquid water. We found that culturable and total microbial biomass in University Valley was extremely low, and microbial activity under ambient conditions was undetectable. Our results contrast with reports from the lower-elevation Dry Valleys and Arctic permafrost soils where active microbial populations are found, suggesting that the combination of severe cold, aridity, oligotrophy of University Valley permafrost soils severely limit microbial activity and survival.

Nearing the cold-arid limits of microbial life in permafrost of an upper dry valley, Antarctica

PubMed Central

Goordial, Jacqueline; Davila, Alfonso; Lacelle, Denis; Pollard, Wayne; Marinova, Margarita M; Greer, Charles W; DiRuggiero, Jocelyn; McKay, Christopher P; Whyte, Lyle G

2016-01-01

Some of the coldest and driest permafrost soils on Earth are located in the high-elevation McMurdo Dry Valleys (MDVs) of Antarctica, but little is known about the permafrost microbial communities other than that microorganisms are present in these valleys. Here, we describe the microbiology and habitable conditions of highly unique dry and ice-cemented permafrost in University Valley, one of the coldest and driest regions in the MDVs (1700 m above sea level; mean temperature −23 °C; no degree days above freezing), where the ice in permafrost originates from vapour deposition rather than liquid water. We found that culturable and total microbial biomass in University Valley was extremely low, and microbial activity under ambient conditions was undetectable. Our results contrast with reports from the lower-elevation Dry Valleys and Arctic permafrost soils where active microbial populations are found, suggesting that the combination of severe cold, aridity, oligotrophy of University Valley permafrost soils severely limit microbial activity and survival. PMID:27323892

Therapeutic Inhibition of Pro-Inflammatory Signaling and Toxicity to Staphylococcal Enterotoxin B by a Synthetic Dimeric BB-Loop Mimetic of MyD88

DTIC Science & Technology

2012-07-27

induce MyD88- mediated signaling [15,16]. Seeking to improve the efficacy of Compound 1 as an inhibitor of MyD88 signaling, we synthesized a dimeric...molecule in which two Compound 1 moieties were covalently linked together, reasoning that the dimeric compound would be a more potent inhibitor of protein...pellets in 50 ml of lysis buffer (Active Motif) in the presence of DTT, protease inhibitors and phosphatase inhibitors and incubated on ice for 30–60

The effects of deoxynivalenol-contaminated corn dried distillers grains with solubles in nursery pig diets and potential for mitigation by commercially available feed additives.

PubMed

Frobose, H L; Fruge, E D; Tokach, M D; Hansen, E L; DeRouchey, J M; Dritz, S S; Goodband, R D; Nelssen, J L

2015-03-01

Four experiments were conducted to investigate the effects of deoxynivalenol (DON) from naturally contaminated dried distillers grains with solubles (DDGS) and the efficacy of feed additives in nursery pig diets. In Exp. 1, 180 pigs (10.3 ± 0.2 kg BW) were fed 1 of 5 diets for 21 d. Diets were 1) Positive Control (PC; < 0.5 mg/kg DON), 2) Negative Control (NC; 4 mg/kg DON), 3) NC + 0.10% Biofix (Biomin Inc., Herzogenburg, Austria), 4) NC + 0.15% Cel-can (VAST Inc., Mason City, IA) and 0.50% bentonite clay, and 5) NC + 0.25% Defusion Plus (Cargill Animal Nutrition, Minneapolis, MN). Pigs fed the NC diet had poorer ( < 0.01) ADG than those fed the PC. Pigs fed Defusion Plus had improved ( < 0.03) ADG over those fed NC, whereas pigs fed Biofix or Cel-can with bentonite clay had reduced ADG ( < 0.01) compared with those fed PC. In Exp. 2, 340 pigs (11.7 ± 0.1 kg BW) were fed 1 of 8 diets for 21 d. Diets were 1) PC (< 0.5 mg/kg DON), 2) Low NC (1.5 mg/kg DON), 3) Low NC + 0.15% Biofix, 4) Low NC + 0.30% Biofix, 5) High NC (3.0 mg/kg DON), 6) High NC + 0.30% Biofix, 7) High NC + 0.45% Biofix, and 8) Diet 7 with 5% added water. Increasing the DON level reduced (linear; < 0.05) ADG, ADFI, and pig BW, and Biofix did not improve performance. In Exp. 3, 1,008 pigs (12.5 ± 0.3 kg BW) were fed 6 treatments for 24 d. Diets were 1) PC ( < 0.5 mg/kg DON), 2) NC (3 mg/kg DON), 3) NC + 0.25% Defusion, 4) NC + 0.50% Defusion, 5) Diet 3 with supplemental nutrients, and 6) Diet 5, pelleted. Pigs fed the NC had decreased ( < 0.01) ADG and ADFI, but adding Defusion improved (linear; < 0.04) ADG and ADFI over pigs fed NC. Pelleting improved ( < 0.01) both ADG and G:F, resulting in ADG above PC pigs. In Exp. 4, 980 pigs (12.0 ± 0.3 kg BW) were fed 1 of 7 diets in a 28-d trial in a 2 × 3 + 1 factorial arrangement. The 7 treatments were based on 3 diets fed in meal or pellet form: 1) PC (< 0.5 mg/kg DON), 2) NC (3 mg/kg DON), and 3) NC + 0.25% Defusion. Treatment 7 was Diet 3 with supplemental nutrients in pellet form. No interactions were observed between pelleting and Defusion. Pigs fed the NC had decreased ( < 0.01) ADG and ADFI, and pelleting improved ( < 0.01) ADG to PC levels, driven by improved ( < 0.01) G:F. Adding nutrients or Defusion had no effect. Overall, these studies show that Defusion and pelleting can help overcome some of the negative effects of DON, whereas other feed additives and additional nutrients do not.

What do preweaned and weaned calves need in the diet: a high fiber content or a forage source?

PubMed

Terré, M; Pedrals, E; Dalmau, A; Bach, A

2013-08-01

The objective of this study was to determine whether the improvement of performance of young calves associated with the supplementation of chopped grass hay reported in some studies is due to an increase in the total neutral detergent fiber (NDF) content of the consumed diet or to the provision of chopped grass hay. Sixty-three Holstein calves [9±4.4 d old; mean ± standard deviation (SD)] were randomly distributed in 4 treatments resulting from the combination of 2 levels of NDF content of a pelleted starter and the supply or absence of forage provision: low-NDF starter (18%) with or without chopped oat hay, and high-NDF starter (27%) with or without chopped oat hay. All animals were fed the same milk replacer (21% crude protein and 19.2% fat) at the rate of 4 L/d at 15% dry matter from d 1 to 34, and 2 L/d at 15% dry matter from d 35 to 42 (weaning). The study finished 2 wk after weaning. Body weight was measured weekly and individual calf starter and hay intake was recorded daily. On d 50, blood samples were drawn 2h after the morning concentrate offer to determine serum glucose and insulin concentrations. On d 52, samples of ruminal fluid were obtained via an esophageal tube, and pH was measured immediately. During the preweaning period, pelleted starter intake was similar among treatments, but average daily gain tended to be greater in low- than in high-NDF treatments (0.69 vs. 0.63±0.020 kg/d, respectively; mean ± SD). However, during the 2 wk after weaning, supplementation of forage improved pelleted starter intake and average daily gain without affecting the gain-to-feed ratio. Probably, the greater pelleted starter intake observed in forage-supplemented calves was mainly due to the greater ruminal pH found in forage-supplemented calves compared with forage-deprived calves (5.81 vs. 5.05±0.063, respectively). Blood insulin-to-glucose ratio was greater in forage-supplemented compared with unsupplemented calves [mean ± SD; 6.53 vs. 4.24±0.125 insulin (ng/L)-to-glucose (mg/dL) ratio, respectively]. In conclusion, a low-NDF pelleted starter is recommended during the preweaning period, and the provision of chopped hay is necessary right after weaning to improve calf performance. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of a completely pelleted diet on growth performance in Holstein heifers.

PubMed

Bonfante, E; Palmonari, A; Mammi, L; Canestrari, G; Fustini, M; Formigoni, A

2016-12-01

Forage neutral detergent fiber (NDF) content and particle size are important factors that affect rumen function. The aim of the current study was to evaluate the effects on rumen health, NDF digestibility, and animal performance of pelleting a forage-based diet. Eight Holstein heifers (age 336±30d, body weight 346±35kg) were randomly assigned to a repeated crossover design. Animals were housed in tie-stalls and fed for ad libitum intake. The study included 4 periods of 3 wk, the first 2 wk for adaptation to the diet and the last wk for data collection. Diets had the same ingredients but had a different physical form: total mixed ration (TMR) and pellet (diameter=8mm). The physically effective NDF (peNDF) differed between the 2 treatments (39.8 and 11.8% of NDF in the TMR and pellet diets, respectively). During the trial, dry matter intake (DMI), water intake, rumination time, rumen temperature, and pH were evaluated daily. Fecal samples were collected in wk3 of each period to determine total-tract digestibility of the potential digestible (pd)NDF. Average daily gain and feed conversion ratio were calculated at the end of each period. With the pellet diet, DMI, DMI/body weight, and water consumption were higher. We observed no significant difference in average daily gain or feed conversion ratio. Rumination time was lower for the pellet diet than for the TMR diet (241 vs. 507min/d, respectively). Diet had no effect on rumen temperature or rumen pH. The total-tract digestibility of the pdNDF was greater with the TMR diet than with the pellet diet (90.25 vs. 86.82% pdNDF, respectively). The results of the current study suggest that a complete-feed pellet diet was well accepted by the animals, as demonstrated by higher DMI. Rumination time was reduced with the pellet diet, but rumen pH was not different. The pdNDF digestibility was high for both diets, but significantly higher for the TMR diet. Given that animal performance was similar between the 2 diets, although they differed with respect to DMI and fiber digestion, we hypothesize that the 2 diets had different retention times, related to their physical form. A complete-feed pellet diet formulated to provide a sufficient level of NDF from forages could be fed to growing ruminants without apparent negative effects on rumen health and animal productivity, at least for a short period. More research over a longer growing period is needed before recommending this feeding strategy for growing heifers. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Dietary Spirulina (Arthrospira platensis) and Thyme (Thymus vulgaris) supplementation to growing rabbits: effects on raw and cooked meat quality, nutrient true retention and oxidative stability.

PubMed

Dalle Zotte, Antonella; Cullere, Marco; Sartori, Alberto; Szendrő, Zsolt; Kovàcs, Melinda; Giaccone, Valerio; Dal Bosco, Alessandro

2014-10-01

The study evaluated the effect of Spirulina and Thyme dietary supplementation on rabbit meat quality, nutrient true retention and protection against oxidative stress. Rabbits in the control group (C-C) received a non-supplemented pellet throughout the experiment (5-11weeks of age). In the other groups, the pellet contained 5% Spirulina (S), 3% Thyme (T), or both (ST) for either the entire (groups S-S, T-T, ST-ST) or only the final part of the growing period (8-11weeks: groups C-S, C-T, C-ST). Spirulina supplementation increased the γ-linolenic acid content of rabbit meat, whereas Thyme improved the oxidative stability of raw and freeze-dried meat. Copyright © 2014 Elsevier Ltd. All rights reserved.

Bacillus thuringiensis in caterpillars and associated materials collected from protected tropical forests in northwestern Costa Rica.

PubMed

Rodríguez-Sánchez, César; Sittenfeld, Ana; Janzen, Daniel H; Espinoza, Ana M

2006-06-01

Bacillus thuringiensis (Bt) synthesizes crystalline inclusions that are toxic to caterpillars (Lepidoptera) and other orders of invertebrates. Materials associated with 37 caterpillars from 16 species, collected while feeding on 15 different species of host plants in dry, cloud and rain forests located in the Area de Conservación Guanacaste in northwestern Costa Rica, were examined for the presence of Bt. From a total of 101 derived samples, 25 Bt isolates were cultured: 56% from host plant leaves, 8% from caterpillar guts and 36% from caterpillar fecal pellets. Bt was isolated from at least one sample in 38% of the systems constituted by the food plant, gut and fecal pellets corresponding to a single caterpillar. Four different morphologies of crystalline inclusions were observed, with bipyramidal and irregular crystal morphologies being the most prevalent.

Fans on Crater Rims

NASA Image and Video Library

2016-12-14

Gas under pressure will choose an easy escape route. In this image, the terrain is covered with a seasonal layer of dry ice. The weak spots, for gas sublimating from the bottom of the seasonal ice layer to escape, appear to be around craters, where the surface was broken and pulverized by an impact. Fans of surface material deposited on top of the seasonal ice layer show where the escape vents are. http://photojournal.jpl.nasa.gov/catalog/PIA21271

Geological and geomorphological insights into Antarctic ice sheet evolution.

PubMed

Sugden, David E; Bentley, Michael J; O Cofaigh, Colm

2006-07-15

Technical advances in the study of ice-free parts of Antarctica can provide quantitative records that are useful for constraining and refining models of ice sheet evolution and behaviour. Such records improve our understanding of system trajectory, influence the questions we ask about system stability and help to define the ice-sheet processes that are relevant on different time-scales. Here, we illustrate the contribution of cosmogenic isotope analysis of exposed bedrock surfaces and marine geophysical surveying to the understanding of Antarctic ice sheet evolution on a range of time-scales. In the Dry Valleys of East Antarctica, 3He dating of subglacial flood deposits that are now exposed on mountain summits provide evidence of an expanded and thicker Mid-Miocene ice sheet. The survival of surface boulders for approximately 14Myr, the oldest yet measured, demonstrates exceptionally low rates of subsequent erosion and points to the persistence and stability of the dry polar desert climate since that time. Increasingly, there are constraints on West Antarctic ice sheet fluctuations during Quaternary glacial cycles. In the Sarnoff Mountains of Marie Byrd Land in West Antarctica, 10Be and 26Al cosmogenic isotope analysis of glacial erratics and bedrock reveal steady thinning of the ice sheet from 10400 years ago to the present, probably as a result of grounding line retreat. In the Antarctic Peninsula, offshore analysis reveals an extensive ice sheet at the last glacial maximum. Based on radiocarbon dating, deglaciation began by 17000cal yr BP and was complete by 9500cal yr BP. Deglaciation of the west and east sides of the Antarctic Peninsula ice sheet occurred at different times and rates, but was largely complete by the Early Holocene. At that time ice shelves were less extensive on the west side of the Antarctic Peninsula than they are today. The message from the past is that individual glacier drainage basins in Antarctica respond in different and distinctive ways to global climate change, depending on the link between regional topography and climate setting.

Satellite-derived, melt-season surface temperature of the Greenland Ice Sheet (2000-2005) and its relationship to mass balance

USGS Publications Warehouse

Hall, D.K.; Williams, R.S.; Casey, K.A.; DiGirolamo, N.E.; Wan, Z.

2006-01-01

Mean, clear-sky surface temperature of the Greenland Ice Sheet was measured for each melt season from 2000 to 2005 using Moderate-Resolution Imaging Spectroradiometer (MODIS)–derived land-surface temperature (LST) data-product maps. During the period of most-active melt, the mean, clear-sky surface temperature of the ice sheet was highest in 2002 (−8.29 ± 5.29°C) and 2005 (−8.29 ± 5.43°C), compared to a 6-year mean of −9.04 ± 5.59°C, in agreement with recent work by other investigators showing unusually extensive melt in 2002 and 2005. Surface-temperature variability shows a correspondence with the dry-snow facies of the ice sheet; a reduction in area of the dry-snow facies would indicate a more-negative mass balance. Surface-temperature variability generally increased during the study period and is most pronounced in the 2005 melt season; this is consistent with surface instability caused by air-temperature fluctuations.

A sublimation heat engine

PubMed Central

Wells, Gary G.; Ledesma-Aguilar, Rodrigo; McHale, Glen; Sefiane, Khellil

2015-01-01

Heat engines are based on the physical realization of a thermodynamic cycle, most famously the liquid–vapour Rankine cycle used for steam engines. Here we present a sublimation heat engine, which can convert temperature differences into mechanical work via the Leidenfrost effect. Through controlled experiments, quantified by a hydrodynamic model, we show that levitating dry-ice blocks rotate on hot turbine-like surfaces at a rate controlled by the turbine geometry, temperature difference and solid material properties. The rotational motion of the dry-ice loads is converted into electric power by coupling to a magnetic coil system. We extend our concept to liquid loads, generalizing the realization of the new engine to both sublimation and the instantaneous vapourization of liquids. Our results support the feasibility of low-friction in situ energy harvesting from both liquids and ices. Our concept is potentially relevant in challenging situations such as deep drilling, outer space exploration or micro-mechanical manipulation. PMID:25731669

A sublimation heat engine.

PubMed

Wells, Gary G; Ledesma-Aguilar, Rodrigo; McHale, Glen; Sefiane, Khellil

2015-03-03

Heat engines are based on the physical realization of a thermodynamic cycle, most famously the liquid-vapour Rankine cycle used for steam engines. Here we present a sublimation heat engine, which can convert temperature differences into mechanical work via the Leidenfrost effect. Through controlled experiments, quantified by a hydrodynamic model, we show that levitating dry-ice blocks rotate on hot turbine-like surfaces at a rate controlled by the turbine geometry, temperature difference and solid material properties. The rotational motion of the dry-ice loads is converted into electric power by coupling to a magnetic coil system. We extend our concept to liquid loads, generalizing the realization of the new engine to both sublimation and the instantaneous vapourization of liquids. Our results support the feasibility of low-friction in situ energy harvesting from both liquids and ices. Our concept is potentially relevant in challenging situations such as deep drilling, outer space exploration or micro-mechanical manipulation.

In-line and real-time process monitoring of a freeze drying process using Raman and NIR spectroscopy as complementary process analytical technology (PAT) tools.

PubMed

De Beer, T R M; Vercruysse, P; Burggraeve, A; Quinten, T; Ouyang, J; Zhang, X; Vervaet, C; Remon, J P; Baeyens, W R G

2009-09-01

The aim of the present study was to examine the complementary properties of Raman and near infrared (NIR) spectroscopy as PAT tools for the fast, noninvasive, nondestructive and in-line process monitoring of a freeze drying process. Therefore, Raman and NIR probes were built in the freeze dryer chamber, allowing simultaneous process monitoring. A 5% (w/v) mannitol solution was used as model for freeze drying. Raman and NIR spectra were continuously collected during freeze drying (one Raman and NIR spectrum/min) and the spectra were analyzed using principal component analysis (PCA) and multivariate curve resolution (MCR). Raman spectroscopy was able to supply information about (i) the mannitol solid state throughout the entire process, (ii) the endpoint of freezing (endpoint of mannitol crystallization), and (iii) several physical and chemical phenomena occurring during the process (onset of ice nucleation, onset of mannitol crystallization). NIR spectroscopy proved to be a more sensitive tool to monitor the critical aspects during drying: (i) endpoint of ice sublimation and (ii) monitoring the release of hydrate water during storage. Furthermore, via NIR spectroscopy some Raman observations were confirmed: start of ice nucleation, end of mannitol crystallization and solid state characteristics of the end product. When Raman and NIR monitoring were performed on the same vial, the Raman signal was saturated during the freezing step caused by reflected NIR light reaching the Raman detector. Therefore, NIR and Raman measurements were done on a different vial. Also the importance of the position of the probes (Raman probe above the vial and NIR probe at the bottom of the sidewall of the vial) in order to obtain all required critical information is outlined. Combining Raman and NIR spectroscopy for the simultaneous monitoring of freeze drying allows monitoring almost all critical freeze drying process aspects. Both techniques do not only complement each other, they also provided mutual confirmation of specific conclusions.

Classification of surface types using SIR-C/X-SAR, Mount Everest Area, Tibet

USGS Publications Warehouse

Albright, Thomas P.; Painter, Thomas H.; Roberts, Dar A.; Shi, Jiancheng; Dozier, Jeff; Fielding, Eric

1998-01-01

Imaging radar is a promising tool for mapping snow and ice cover in alpine regions. It combines a high-resolution, day or night, all-weather imaging capability with sensitivity to hydrologic and climatic snow and ice parameters. We use the spaceborne imaging radar-C/X-band synthetic aperture radar (SIR-C/X-SAR) to map snow and glacial ice on the rugged north slope of Mount Everest. From interferometrically derived digital elevation data, we compute the terrain calibration factor and cosine of the local illumination angle. We then process and terrain-correct radar data sets acquired on April 16, 1994. In addition to the spectral data, we include surface slope to improve discrimination among several surface types. These data sets are then used in a decision tree to generate an image classification. This method is successful in identifying and mapping scree/talus, dry snow, dry snow-covered glacier, wet snow-covered glacier, and rock-covered glacier, as corroborated by comparison with existing surface cover maps and other ancillary information. Application of the classification scheme to data acquired on October 7 of the same year yields accurate results for most surface types but underreports the extent of dry snow cover.

[Growth inhibition of Vibrio parahaemolyticus in seafood by tabletop dry ice cooler].

PubMed

Maruyama, Yumi; Kimura, Bon; Fujii, Tateo; Tokunaga, Yoshinori; Matsubayashi, Megumi; Aikawa, Yasushi

2005-10-01

Tabletop dry ice coolers (three types; dome model, cap model and tripod model), which are used in kitchens and hotel banquet halls to refrigerate fresh seafood, were investigated to determine whether growth of Vibrio parahaemolyticus was inhibited by their use. On TSA plates containing 1.8% NaCl and fresh seafood (fillets of squid, pink shrimp and yellowtail), V. parahaemolyticus (O3:K6, TDH+) inoculated at 4 to 5 log CFU/sample and left at ambient temperature (25 degrees C) grew by 1.0 to 2.8 orders in 4 hours. In contrast, with tabletop coolers no significant increase in viable count occurred in 3 to 4 hours, confirming that tabletop coolers inhibited the growth of V. parahaemolyticus. The temperature in each tabletop cooler was kept below 10 degrees C for 80 to 135 min, though the CO2 gas concentration in them remained high for only a short time (0 to 75 min). It was presumed that the refrigeration function mainly contributed to growth inhibition. Our results indicate that tabletop dry ice coolers are helpful for prevention of food-borne disease due to V. parahaemolyticus in food-service locations, such as kitchens and banquet halls.

Comparative efficiency of two models of CO2 traps in the collection of free-living stages of ixodides.

PubMed

Guedes, Elizângela; de Azevedo Prata, Márcia Cristina; dos Reis, Eder Sebastião; Cançado, Paulo Henrique Duarte; Leite, Romário Cerqueira

2012-12-01

Traps using carbon dioxide (CO(2)) as a chemical attractant are known to be effective when capturing nymphs and adults of some free-living tick species such as Amblyomma cajennense and Amblyomma parvum. Despite the fact that the main source of CO(2) is dry ice, the chemical trap which uses 20 % lactic acid (C(3)H(6)O(3)) and calcium carbonate (CaCO(3)) has been tested as an alternative source of CO(2) whenever it is difficult to obtain dry ice. The objective of this paper was to test and compare the efficiency of these two models of traps during the study of population dynamics of A. cajennense and Amblyomma dubitatum in Coronel Pacheco, Minas Gerais, Brazil. Within the period comprising May 2006 to April 2008, eight CO(2) traps, of which four were dry ice and four chemical, were put in the pasture every 14 days at preestablished areas over a 1.0-m(2) white cotton flannel cloth with a capture dispositive which constituted of double-sided adhesive tapes fixed onto the four corners of the flannels. On every collection day, a cotton flannel without any chemical attractant was placed in the same area of the pasture to become an instrument to control the traps' capture efficiency. After 1 h, the white flannels were collected and placed in plastic bags for later identification and counting of the ticks. A total of 2,133 nymphs of Amblyomma sp., 328 adults of A. cajennense, and 292 adults of A. dubitatum were collected. Out of this total, the dry ice traps captured 1,087 nymphs (51 %), 188 A. cajennense (58.2 %), and 151 A. dubitatum (53 %), while the chemical traps captured 1,016 nymphs (47.6 %), 133 A. cajennense (41 %), and 133 A. dubitatum (46.5 %); 30 nymphs (1.4 %), 7 A. cajennense (0.8 %), and 8 A. dubitatum (0.5 %) were found on the control flannel. The capture potentials of ticks, nymphs, and adults, by the two models of traps tested, were statistically similar (p > 0.05). These results confirm the efficiency of the chemical trap enabling its use in areas of either difficult access or too distant from a dry ice supplier as is the case of forest areas where studies about ixodological fauna are generally carried out.

A World of Snowy Dunes

NASA Image and Video Library

2017-08-21

It is spring in the Northern hemisphere when NASA's Mars Reconnaissance Orbiter took this image. Over the winter, snow and ice have inexorably covered the dunes. Unlike on Earth, this snow and ice is carbon dioxide, better known to us as dry ice. When the sun starts shining on it in the spring, the ice on the smooth surface of the dune cracks and escaping gas carries dark sand out from the dune below, often creating beautiful patterns. On the rough surface between the dunes, frost is trapped behind small sheltered ridges. https://photojournal.jpl.nasa.gov/catalog/PIA21882

E-Screen evaluation of sugar beet feedstuffs in a case of reduced embryo transfer efficiencies in cattle: the role of phytoestrogens and zearalenone

USDA-ARS?s Scientific Manuscript database

The E-Screen assay was used to evaluate the estrogenicity of sugar beet by-products obtained from a dairy farm experiencing low success rates of embryo transfer. The beet tailings had ~ 3 fold the estradiol equivalents of the pelleted beet pulp (3.9 and 1.2 µg estradiol equivalents or E2Eq/kg dry m...

The control of ice crystal growth and effect on porous structure of konjac glucomannan-based aerogels.

PubMed

Ni, Xuewen; Ke, Fan; Xiao, Man; Wu, Kao; Kuang, Ying; Corke, Harold; Jiang, Fatang

2016-11-01

Konjac glucomannan (KGM)-based aerogels were prepared using a combination of sol-gel and freeze-drying methods. Preparation conditions were chosen to control ice crystal growth and aerogel structure formation. The ice crystals formed during pre-freezing were observed by low temperature polarizing microscopy, and images of aerogel pores were obtained by scanning electron microscopy. The size of ice crystals were calculated and size distribution maps were drawn, and similarly for aerogel pores. Results showed that ice crystal growth and aerogel pore sizes may be controlled by varying pre-freezing temperatures, KGM concentration and glyceryl monostearate concentration. The impact of pre-freezing temperatures on ice crystal growth was explained as combining ice crystal growth rate with nucleation rate, while the impacts of KGM and glyceryl monostearate concentration on ice crystal growth were interpreted based on their influences on sol network structure. Copyright © 2016 Elsevier B.V. All rights reserved.

Radar backscattering from snow facies of the Greenland ice sheet: Results from the AIRSAR 1991 campaign

NASA Technical Reports Server (NTRS)

Rignot, Eric; Jezek, K.; Vanzyl, J. J.; Drinkwater, Mark R.; Lou, Y. L.

1993-01-01

In June 1991, the NASA/JPL airborne SAR (AIRSAR) acquired C- (lambda = 5.6cm), L- (lambda = 24cm), and P- (lambda = 68m) band polarimetric SAR data over the Greenland ice sheet. These data are processed using version 3.55 of the AIRSAR processor which provides radiometrically and polarimetrically calibrated images. The internal calibration of the AIRSAR data is cross-checked using the radar response from corner reflectors deployed prior to flight in one of the scenes. In addition, a quantitative assessment of the noise power level at various frequencies and polarizations is made in all the scenes. Synoptic SAR data corresponding to a swath width of about 12 by 50 km in length (compared to the standard 12 x 12 km size of high-resolution scenes) are also processed and calibrated to study transitions in radar backscatter as a function of snow facies at selected frequencies and polarizations. The snow facies on the Greenland ice sheet are traditionally categorized based on differences in melting regime during the summer months. The interior of Greenland corresponds to the dry snow zone where terrain elevation is the highest and no snow melt occurs. The lowest elevation boundary of the dry snow zone is known traditionally as the dry snow line. Beneath it is the percolation zone where melting occurs in the summer and water percolates through the snow freezing at depth to form massive ice lenses and ice pipes. At the downslope margin of this zone is the wet snow line. Below it, the wet snow zone corresponds to the lowest elevations where snow remains at the end of the summer. Ablation produces enough meltwater to create areas of snow saturated with water, together with ponds and lakes. The lowest altitude zone of ablation sees enough summer melt to remove all traces of seasonal snow accumulation, such that the surface comprises bare glacier ice.

Experimental investigation of passive infrared ice detection for helicopter applications

NASA Technical Reports Server (NTRS)

Dershowitz, Adam; Hansman, R. John, Jr.

1991-01-01

A technique is proposed to remotely detect rotor icing on helicopters. Using passive infrared (IR) thermometry it is possible to detect the warming caused by latent heat released as supercooled water freezes. During icing, the ice accretion region on the blade leading edge will be warmer than the uniced trailing edge resulting in a chordwise temperature profile characteristic of icing. Preliminary tests were conducted on a static model in the NASA Icing Research Tunnel for a variety of wet (glaze) and dry (rime) ice conditions. The characteristic chordwise temperature profiles were observed with an IR thermal video system and confirmed with thermocouple measurements. A prototype detector system was built consisting of a single point IR pyrometer, and experiments were run on a small scale rotor model. Again the characteristic chordwise temperature profiles were observed during icing, and the IR system was able to remotely detect icing. Based on the static and subscale rotor tests the passive IR technique is promising for rotor ice detection.

Experimental investigation of passive infrared ice detection for helicopter applications

NASA Technical Reports Server (NTRS)

Dershowitz, Adam; Hansman, R. John, Jr.

1991-01-01

A technique is proposed to remotely detect rotor icing on helicopters. Using passive infrared (IR) thermometry, it is possible to detect the warming caused by latent heat released as supercooled water freezes. During icing, the ice accretion region on the blade leading edge will be warmer than the uniced trailing edge, resulting in a chordwise temperature profile characteristic of icing. Preliminary tests were conducted on a static model in the NASA Icing Research Tunnel for a variety of wet (glaze) and dry (rime) ice conditions. The characteristic chordwise temperature profiles were observed with an IR thermal video system and confirmed with thermocouple measurements. A prototype detector system was built consisting of a single point IR pyrometer. Experiments were run on a small scale rotor model. Again, the characteristic chordwise temperature profiles were observed during icing, and the IR system was able to remotely detect icing. Based on the static and subscale rotor tests, the passive IR technique is promising for rotor ice detection.

Dynamic Tensile Strength of Low Temperature Ice and Kuiper Belt Size Distributions

NASA Astrophysics Data System (ADS)

Ahrens, Thomas J.; Fat'yanov, O. V.; Engelhardt, H.; Fraser, W. C.

2009-09-01

We model mutual gravitationally driven impact interactions in a nearly gas-free environment of the Kuiper belt (KB) and use low-temperature (< 100 K) ice dynamic strength dependent collisional out-come (accretion vs. erosion and fragmentation) models. These lead to theoretically predictable distributions of object number density, vs. mass distributions. These derived mass distributions are comparable to the now rapidly growing KB survey data. Tensional failure of single and polycrystalline ice in the temperature range from 263 to 128 K was measured for high strain rate, c.a. 104 s-1, dynamic loading conditions. Experiments, similar to Lange and Ahrens(1991)(LA), were conducted using a gas gun launched Lexan projectile. The liquid nitrogen cooled ice target approaching KB-like temperatures was partially confined, rather than using the LA confined geometry. Another set of experiments used a drop tube projectile launcher within the 263 K Caltech Ice Laboratory and at 163 K in a liquid nitrogen cooled chamber. New experiments give tensile strengths of 7.6±1.5 MPa at 263 K and 9.1±1.5 MPa at 163 K for unconfined, free of visual initial defects and measurable imperfections ice samples. The new strengths are lower than the earlier LA data ( 17 MPa). The major differences arise from ice target assembly. LA used polycrystalline ice samples confined in annular stainless steel target rings. New measurements were partially confined, in not initially contacting concentric target rings. Later shots used unconfined configurations with ice pellets affixed to aluminum foil. Circumferential confinement is known to increase the material damage threshold upon both compression and tensile loading. Previous confinement in LA is the main cause of the above discrepancy. Present tensile strengths are only a few times higher than 0.7 - 3.0 MPa summarized in Petrovic (2003) for quasistatic tension at 10-7 to 10-3 s-1 strain rate.

The Canadian Defence Input-Output Model DIO Version 4.41

DTIC Science & Technology

2011-09-01

0841 Mineral water, fruit-flavoured beverages and ice 99 0842 Pasta products, excluding dry pasta 100 0843 Prepared meals 101 0850 Feed supplements and...junior foods, excluding in airtight containers 134 1136 Dry pasta 135 1140 Soft drink concentrates 136 1150 Carbonated soft drinks 137 1161 Distilled

Factors affecting oxidative stain in soft maple (Acer rubrum L.)

Treesearch

Michael C. Wiemann; Mark Knaebe

2008-01-01

A preliminary study to determine possible treatments that might be used to eliminate or limit value reducing stain in soft maple suggests that rapid processing and treatment with sulfur dioxide gas decreases discoloration, high-temperature drying increases discoloration, and freezing in dry ice prior to processing has no effect.

Under-ice availability of phytoplankton lipids is key to freshwater zooplankton winter survival.

PubMed

Grosbois, Guillaume; Mariash, Heather; Schneider, Tobias; Rautio, Milla

2017-09-14

Shortening winter ice-cover duration in lakes highlights an urgent need for research focused on under-ice ecosystem dynamics and their contributions to whole-ecosystem processes. Low temperature, reduced light and consequent changes in autotrophic and heterotrophic resources alter the diet for long-lived consumers, with consequences on their metabolism in winter. We show in a survival experiment that the copepod Leptodiaptomus minutus in a boreal lake does not survive five months under the ice without food. We then report seasonal changes in phytoplankton, terrestrial and bacterial fatty acid (FA) biomarkers in seston and in four zooplankton species for an entire year. Phytoplankton FA were highly available in seston (2.6 µg L -1 ) throughout the first month under the ice. Copepods accumulated them in high quantities (44.8 µg mg dry weight -1 ), building lipid reserves that comprised up to 76% of body mass. Terrestrial and bacterial FA were accumulated only in low quantities (<2.5 µg mg dry weight -1 ). The results highlight the importance of algal FA reserve accumulation for winter survival as a key ecological process in the annual life cycle of the freshwater plankton community with likely consequences to the overall annual production of aquatic FA for higher trophic levels and ultimately for human consumption.

A Leidenfrost Engine

NASA Astrophysics Data System (ADS)

Wells, Gary; Ledesma-Aguillar, Ridrigo; McHale, Glen; Sefiane, Khellil

2015-11-01

The Leidenfrost effect, the sustained levitation of evaporating liquid droplets by a cushion of their on vapour on very hot surfaces, has received increased attention over the past few years. On patterned surfaces, rectification of the vapour layer flow can lead to rich dynamics of evaporating drops or sublimating blocks of dry ice, including self-propulsion, orbiting and conjoint rotation. In this paper we show that the Leidenfrost effect can be exploited to drive the rotation of rigid objects, such as solid hydrophilic plates coupled to water droplets and blocks of dry ice, by using turbine-like substrates. Using a hydrodynamic model, we show that drag-based rotation is achieved at low-Reynolds number by a rectification mechanism of the flow in the vapour layer caused by the underlying turbine-like geometry. Our theoretical model determines the maximum weight of Leidenfrost rotors and the net torque driving their motion in terms of operational parameters, showing an excellent agreement with experiments using dry-ice blocks. We generalise the concept of rotation into a new concept for a heat engine capable of harvesting thermal energy using either thin-film boiling or sublimation as a phase-change mechanism. As a proof principle, we implement the new sublimation engine in the lab to create a simple electromagnetic generator. Our results support the feasibility of low-friction in situ energy harvesting from both liquids and ices in challenging situations such as deep drilling, outer space exploration or micro-mechanical manipulation.

Wide, Branching Channels

NASA Image and Video Library

2017-01-11

Southern spring on Mars brings sublimation of the seasonal dry ice polar cap. Gas trapped under the seasonal ice sheet carves channels on its way to escaping to the atmosphere. At this site, the channels are wider than we see elsewhere on Mars, perhaps meaning that the spider-like (or more scientifically, "araneiform") terrain here is older, or that the surface is more easily eroded. Seasonal fans of eroded surface material, pointed in two different directions, are deposited on the remaining ice. http://photojournal.jpl.nasa.gov/catalog/PIA13151

The distribution, structure, and composition of freshwater ice deposits in Bolivian salt lakes

USGS Publications Warehouse

Hurlbert, S.H.; Chang, Cecily C.Y.

1988-01-01

Freshwater ice deposits are described from seven, high elevation (4117-4730 m), shallow (mean depth <30 cm), saline (10-103 g l-1) lakes in the southwestern corner of Bolivia. The ice deposits range to several hundred meters in length and to 7 m in height above the lake or playa surface. They are located near the lake or salar margins; some are completely surrounded by water, others by playa deposits or salt crusts. Upper surfaces and sides of the ice deposits usually are covered by 20-40 cm of white to light brown, dry sedimentary materials. Calcite is the dominant crystalline mineral in these, and amorphous materials such as diatom frustules and volcanic glass are also often abundant. Beneath the dry overburden the ice occurs primarily as horizontal lenses 1-1000 mm thick, irregularly alternating with strata of frozen sedimentary materials. Ice represents from 10 to 87% of the volume of the deposits and yields freshwater (TFR <3 g l-1) when melted. Oxygen isotope ratios for ice are similar to those for regional precipitation and shoreline seeps but much lower than those for the lakewaters. Geothermal flux is high in the region as evidenced by numerous hot springs and deep (3.0-3.5 m) sediment temperatures of 5-10??C. This flux is one cause of the present gradual wasting away of these deposits. Mean annual air temperatures for the different lakes probably are all in the range of -2 to 4??C, and mean midwinter temperatures about 5??C lower. These deposits apparently formed during colder climatic conditions by the freezing of low salinity porewaters and the building up of segregation ice lenses. ?? 1988 Dr W. Junk Publishers.

Geothermal flux and basal melt rate in the Dome C region inferred from radar reflectivity and heat modelling

NASA Astrophysics Data System (ADS)

Passalacqua, Olivier; Ritz, Catherine; Parrenin, Frédéric; Urbini, Stefano; Frezzotti, Massimo

2017-09-01

Basal melt rate is the most important physical quantity to be evaluated when looking for an old-ice drilling site, and it depends to a great extent on the geothermal flux (GF), which is poorly known under the East Antarctic ice sheet. Given that wet bedrock has higher reflectivity than dry bedrock, the wetness of the ice-bed interface can be assessed using radar echoes from the bedrock. But, since basal conditions depend on heat transfer forced by climate but lagged by the thick ice, the basal ice may currently be frozen whereas in the past it was generally melting. For that reason, the risk of bias between present and past conditions has to be evaluated. The objective of this study is to assess which locations in the Dome C area could have been protected from basal melting at any time in the past, which requires evaluating GF. We used an inverse approach to retrieve GF from radar-inferred distribution of wet and dry beds. A 1-D heat model is run over the last 800 ka to constrain the value of GF by assessing a critical ice thickness, i.e. the minimum ice thickness that would allow the present local distribution of basal melting. A regional map of the GF was then inferred over a 80 km × 130 km area, with a N-S gradient and with values ranging from 48 to 60 mW m-2. The forward model was then emulated by a polynomial function to compute a time-averaged value of the spatially variable basal melt rate over the region. Three main subregions appear to be free of basal melting, two because of a thin overlying ice and one, north of Dome C, because of a low GF.

Calibration of a geophysically based model using soil moisture measurements in mountainous terrains

NASA Astrophysics Data System (ADS)

Pellet, Cécile; Hilbich, Christin; Marmy, Antoine; Hauck, Christian

2016-04-01

The use of geophysical methods in the field of permafrost research is well established and crucial since it is the only way to infer the composition of the subsurface material. Since geophysical measurements are indirect, ambiguities in the interpretation of the results can arise, hence the simultaneous use of several methods (e.g. electrical resistivity tomography and refraction seismics) is often necessary. The so-called four-phase model, 4PM (Hauck et al., 2011) constitutes a further step towards clarification of interpretation from geophysical measurements. It uses two well-known petrophysical relationships, namely Archie's law and an extension of Timur's time-averaged equation for seismic P-wave velocities, to quantitatively estimate the different phase contents (air, water and ice) in the ground from tomographic electric and seismic measurements. In this study, soil moisture measurements were used to calibrate the 4PM in order to assess the spatial distribution of water, ice and air content in the ground at three high elevation sites with different ground properties and thermal regimes. The datasets used here were collected as part of the SNF-project SOMOMOUNT. Within the framework of this project a network of six entirely automated soil moisture stations was installed in Switzerland along an altitudinal gradient ranging from 1'200 m. a.s.l. to 3'400 m. a.s.l. The standard instrumentation of each station comprises the installation of Frequency Domain Reflectometry (FDR) and Time Domain Reflectometry (TDR) sensors for long term monitoring coupled with repeated Electrical Resistivity Tomography (ERT) and Refraction Seismic Tomography (RST) as well as spatial FDR (S-FDR) measurements. The use of spatially distributed soil moisture data significantly improved the 4PM calibration process and a semi-automatic calibration scheme was developed. This procedure was then tested at three different locations, yielding satisfactory two dimensional distributions of water-, ice- and air content (Pellet et al., 2016). REFERENCES Hauck, C., Böttcher, M., & Maurer, H. 2011: A new model for estimating subsurface ice content based on combined electrical and seismic data sets, The Cryosphere, 5(2), 453-468. Pellet, C., Hilbich, C., Marmy, A., & Hauck, C. 2016: Soil moisture data for the validation of permafrost models using direct and indirect measurement approaches at three alpine sites, Front. Earth Sci., 3(91).

Factors associated with the serological prevalence of Salmonella enterica in Greek finishing swineherds.

PubMed Central

Leontides, L. S.; Grafanakis, E.; Genigeorgis, C.

2003-01-01

Blood samples were taken from 50 finishing pigs at 90-105 kg in each of 59 randomly selected farrow-to-finish herds. The sera were tested for antibodies to Salmonella enterica by the Danish mix-ELISA. Samples with an optical density of > 10% were considered to be positive. Associations between the odds of seropositivity of pigs and possible risk factors were evaluated in multivariable logistic regression models. The results of the analysis indicated that pigs fed non-pelleted dry or wet ration had 11 (P = 0.0004) or 9 (P = 0.02) times, respectively, lower odds of seropositivity than those fed pelleted ration. The risk of seropositivity was 4 (P = 0.0006) times higher in pigs fed a combination of chlortetracycline, procaine penicillin and sulphamethazine during fattening than in those fed an approved growth promotor or a probiotic. PMID:12948357

A passive infrared ice detection technique for helicopter applications

NASA Technical Reports Server (NTRS)

Dershowitz, Adam L.; Hansman, R. John, Jr.

1991-01-01

A technique has been developed, and successfully tested, to detect icing remotely on helicopter rotor blades. Using passive infrared (IR) thermometry it is possible to detect the warming caused by latent heat released as supercooled water freezes. During icing, the ice accretion region on the leading edge of the blade is found to be warmer than the uniced trailing edge resulting in a chordwise temperature profile characteristic of icing. Preliminary tests, using an IR Thermal video system, were conducted on a static model in the NASA Icing Research Tunnel (IRT) for a variety of wet (glaze) and dry (rime) ice conditions. A prototype detector system was built consisting of a single point IR pyrometer, and experiments were run on a small scale rotor model. Using this prototype detector, the characteristic chordwise temperature profiles were again observed for a range of icing conditions. Several signal processing methods were investigated, to allow automatic recognition of the icing signature. Additionally, several implementation issues were considered. Based on both the static and subscale rotor tests, where ice was successfully detected, the passive IR technique appears to be promising for rotor ice detection.

Adsorption inhibition as a mechanism of freezing resistance in polar fishes.

PubMed Central

Raymond, J A; DeVries, A L

1977-01-01

Polar fishes are known to have serum proteins and glycoproteins that protect them from freezing, by a noncolligative process. Measurements of antifreeze concentrations in ice and scanning electron micrographs of freeze-dried antifreeze solutions indicate that the antifreezes are incorporated in ice during freezing. The antifreezes also have a pronounced effect on the crystal habit of ice grown in their presence. Each of four antifreezes investigated caused ice to grow in long needles whose axes were parallel to the ice c axis. Together these results indicate the antifreezes adsorb to ice surfaces and inhibit their growth. A model in which adsorbed antifreezes raise the curvature of growth steps on the ice surface is proposed to account for the observed depression of the temperature at which freezing occurs and agrees well with experimental observations. The model is similar to one previously proposed for other cases of crystal growth inhibition. Images PMID:267952

Observed large-scale structures and diabatic heating and drying profiles during TWP-ICE

DOE PAGES

Xie, Shaocheng; Hume, Timothy; Jakob, Christian; ...

2010-01-01

This study documents the characteristics of the large-scale structures and diabatic heating and drying profiles observed during the Tropical Warm Pool–International Cloud Experiment (TWP-ICE), which was conducted in January–February 2006 in Darwin during the northern Australian monsoon season. The examined profiles exhibit significant variations between four distinct synoptic regimes that were observed during the experiment. The active monsoon period is characterized by strong upward motion and large advective cooling and moistening throughout the entire troposphere, while the suppressed and clear periods are dominated by moderate midlevel subsidence and significant low- to midlevel drying through horizontal advection. The midlevel subsidence andmore » horizontal dry advection are largely responsible for the dry midtroposphere observed during the suppressed period and limit the growth of clouds to low levels. During the break period, upward motion and advective cooling and moistening located primarily at midlevels dominate together with weak advective warming and drying (mainly from horizontal advection) at low levels. The variations of the diabatic heating and drying profiles with the different regimes are closely associated with differences in the large-scale structures, cloud types, and rainfall rates between the regimes. Strong diabatic heating and drying are seen throughout the troposphere during the active monsoon period while they are moderate and only occur above 700 hPa during the break period. The diabatic heating and drying tend to have their maxima at low levels during the suppressed periods. Furthermore, the diurnal variations of these structures between monsoon systems, continental/coastal, and tropical inland-initiated convective systems are also examined.« less

Ancient ice islands in salt lakes of the Central Andes

USGS Publications Warehouse

Hurlbert, S.H.; Chang, Cecily C.Y.

1984-01-01

Massive blocks of freshwater ice and frozen sediments protrude from shallow, saline lakes in the Andes of southwestern Bolivia and northeastern Chile. These ice islands range up to 1.5 kilometers long, stand up to 7 meters above the water surface, and may extend out tens of meters and more beneath the unfrozen lake sediments. The upper surfaces of the islands are covered with dry white sediments, mostly aragonite or calcite. The ice blocks may have formed by freezing of the fresh pore water of lake sediments during the "little ice age." The largest blocks are melting rapidly because of possibly recent increases in geothermal heat flux through the lake bottom and undercutting by warm saline lake water during the summer.

Fatality in a wine vat.

PubMed

La Harpe, Romano; Shiferaw, Kebede; Mangin, Patrice; Burkhardt, Sandra

2013-06-01

Intoxication with carbon dioxide (CO2), a nonexplosive, colorless, and odorless gas does not cause any clinical symptoms or signs, with the occasional exception of sudation. Carbon dioxide is principally used in the food industry (70% of CO2 production), in particular to preserve foods and to carbonate beverages. Most fatalities resulting from CO2 intoxication are accidental and occur either in closed spaces or when dry ice is used in the food industry. In this case report, a 42-year-old male winemaker engineer was found dead, his head inside a wine vat that had been filled with grapes on the previous day and supplemented with dry ice to improve the taste of wine.

Accumulation Rates in the Dry Snow Zone of the Greenland Ice Sheet Inferred from L-band InSAR Data

NASA Astrophysics Data System (ADS)

Chen, A. C.; Zebker, H. A.

2012-12-01

The Greenland ice sheet contains about 2.9 million km3 of ice and would raise global sea levels by about 7.1 m if it melted completely. Two unusually large iceberg calving events at Petermann Glacier in the past several years, along with the unusually large extent of ice sheet melt this summer point to the relevance of understanding the mass balance of the Greenland ice sheet. In this study, we use data from the PALSAR instrument aboard the ALOS satellite to form L-band (23-centimeter carrier wavelength) InSAR images of the dry snow zone of the Greenland ice sheet. We form geocoded differential interferograms, using the ice sheet elevation model produced by Howat et.al. [1]. By applying phase and radiometric calibration, we can examine interferograms formed between any pair of transmit and receive polarization channels. In co-polarized interferograms, the InSAR correlation ranges from about 0.35 at the summit (38.7 deg W, 73.0 deg N) where accumulation is about 20 cm w.e./yr to about 0.70 at the north-eastern part of the dry snow zone (35.1 deg W, 77.1 deg N), where accumulation is about 11.7 cm w.e./yr. Cross-polarized interferograms show similar geographic variation with overall lower correlation. We compare our InSAR data with in-situ measurements published by Bales et.al. [2]. We examine the applicability of dense-medium radiative transfer electromagnetic scattering models for estimating accumulation rates from L-band InSAR data. The large number and broad coverage of ALOS scenes acquired between 2007 and 2009 with good InSAR coherence at 46-day repeat times and 21.5 degree incidence angles gives us the opportunity to examine the empirical relationship between in-situ accumulation rate observations and the polarimetric InSAR correlation and radar brightness at this particular imaging geometry. This helps us quantify the accuracy of accumulation rates estimated from InSAR data. In some regions, 46-day interferograms acquired in the winters of several consecutive years allows us to investigate the variability of L-band InSAR correlation over time. [1] Howat I.M., A. Negrete, T. Scambos, T. Haran, in prep, A high-resolution elevation model for the Greenland Ice Sheet from combined stereoscopic and photoclinometric data. [2] [1] R. C. Bales, J. R. McConnell, E. Mosley-Thompson, and B. Csatho, "Accumulation over the Greenland ice sheet from historical and recent records," Journal of Geophysical Research, vol. 106, pp. 33813-33825, 2001.

Experimental Technique and Assessment for Measuring the Convective Heat Transfer Coefficient from Natural Ice Accretions

NASA Technical Reports Server (NTRS)

Masiulaniec, K. Cyril; Vanfossen, G. James, Jr.; Dewitt, Kenneth J.; Dukhan, Nihad

1995-01-01

A technique was developed to cast frozen ice shapes that had been grown on a metal surface. This technique was applied to a series of ice shapes that were grown in the NASA Lewis Icing Research Tunnel on flat plates. Nine flat plates, 18 inches square, were obtained from which aluminum castings were made that gave good ice shape characterizations. Test strips taken from these plates were outfitted with heat flux gages, such that when placed in a dry wind tunnel, can be used to experimentally map out the convective heat transfer coefficient in the direction of flow from the roughened surfaces. The effects on the heat transfer coefficient for both parallel and accelerating flow will be studied. The smooth plate model verification baseline data as well as one ice roughened test case are presented.

40 CFR Appendix 2 to Subpart A of... - Drilling Fluids Toxicity Test

Code of Federal Regulations, 2011 CFR

2011-07-01

... are designed to minimize sample contamination and alteration of the physical or chemical properties of... wet ice (do not use dry ice) and continuously maintained at 0-4 °C until the time of testing. (3) Bulk... use. (5) Most drilling mud samples may be stored for periods of time longer than 2 weeks prior to...

40 CFR Appendix 2 to Subpart A of... - Drilling Fluids Toxicity Test

Code of Federal Regulations, 2010 CFR

2010-07-01

... are designed to minimize sample contamination and alteration of the physical or chemical properties of... wet ice (do not use dry ice) and continuously maintained at 0-4 °C until the time of testing. (3) Bulk... use. (5) Most drilling mud samples may be stored for periods of time longer than 2 weeks prior to...

Subsurface ice and brine sampling using an ultrasonic/sonic gopher for life detection and characterization in the McMurdo Dry Valleys

NASA Technical Reports Server (NTRS)

Bar-Cohen, Y.; Sherrit, S.; Chang, Z.; Wessel, L.; Bao, X.; Doran, P. T.; Fritsen, C. H.; Kenig, F.; McKay, C. P.; Murray, A.;

Carbon accumulation in a permafrost polygon peatland: steady long-term rates in spite of shifts between dry and wet conditions.

PubMed

Gao, Yang; Couwenberg, John

2015-02-01

Ice-wedge polygon peatlands contain a substantial part of the carbon stored in permafrost soils. However, little is known about their long-term carbon accumulation rates (CAR) in relation to shifts in vegetation and climate. We collected four peat profiles from one single polygon in NE Yakutia and cut them into contiguous 0.5 cm slices. Pollen density interpolation between AMS (14)C dated levels provided the time span contained in each of the sample slices, which--in combination with the volumetric carbon content--allowed for the reconstruction of CAR over decadal and centennial timescales. Vegetation representing dry palaeo-ridges and wet depressions was reconstructed with detailed micro- and macrofossil analysis. We found repeated shifts between wet and dry conditions during the past millennium. Dry ridges with associated permafrost growth originated during phases of (relatively) warm summer temperature and collapsed during relatively cold phases, illustrating the important role of vegetation and peat as intermediaries between ambient air temperature and the permafrost. The average long-term CAR across the four profiles was 10.6 ± 5.5 g C m(-2) yr(-1). Time-weighted mean CAR did not differ significantly between wet depression and dry ridge/hummock phases (10.6 ± 5.2 g C m(-2) yr(-1) and 10.3 ± 5.7 g C m(-2) yr(-1), respectively). Although we observed increased CAR in relation to warm shifts, we also found changes in the opposite direction and the highest CAR actually occurred during the Little Ice Age. In fact, CAR rather seems to be governed by strong internal feedback mechanisms and has roughly remained stable on centennial time scales. The absence of significant differences in CAR between dry ridge and wet depression phases suggests that recent warming and associated expansion of shrubs will not affect long-term rates of carbon burial in ice-wedge polygon peatlands. © 2014 John Wiley & Sons Ltd.

Reduction of Iron-Oxide-Carbon Composites: Part II. Rates of Reduction of Composite Pellets in a Rotary Hearth Furnace Simulator

NASA Astrophysics Data System (ADS)

Halder, S.; Fruehan, R. J.

2008-12-01

A new ironmaking concept is being proposed that involves the combination of a rotary hearth furnace (RHF) with an iron-bath smelter. The RHF makes use of iron-oxide-carbon composite pellets as the charge material and the final product is direct-reduced iron (DRI) in the solid or molten state. This part of the research includes the development of a reactor that simulated the heat transfer in an RHF. The external heat-transport and high heating rates were simulated by means of infrared (IR) emitting lamps. The reaction rates were measured by analyzing the off-gas and computing both the amount of CO and CO2 generated and the degree of reduction. The reduction times were found to be comparable to the residence times observed in industrial RHFs. Both artificial ferric oxide (PAH) and naturally occurring hematite and taconite ores were used as the sources of iron oxide. Coal char and devolatilized wood charcoal were the reductants. Wood charcoal appeared to be a faster reductant than coal char. However, in the PAH-containing pellets, the reverse was found to be true because of heat-transfer limitations. For the same type of reductant, hematite-containing pellets were observed to reduce faster than taconite-containing pellets because of the development of internal porosity due to cracking and fissure formation during the Fe2O3-to-Fe3O4 transition. This is, however, absent during the reduction of taconite, which is primarily Fe3O4. The PAH-wood-charcoal pellets were found to undergo a significant amount of swelling at low-temperature conditions, which impeded the external heat transport to the lower layers. If the average degree of reduction targeted in an RHF is reduced from 95 to approximately 70 pct by coupling the RHF with a bath smelter, the productivity of the RHF can be enhanced 1.5 to 2 times. The use of a two- or three-layer bed was found to be superior to that of a single layer, for higher productivities.

Scanning electron microscopy of high-pressure-frozen sea urchin embryos.

PubMed

Walther, P; Chen, Y; Malecki, M; Zoran, S L; Schatten, G P; Pawley, J B

1993-12-01

High-pressure-freezing permits direct cryo-fixation of sea urchin embryos having a defined developmental state without the formation of large ice crystals. We have investigated preparation protocols for observing high-pressure-frozen and freeze-fractured samples in the scanning electron microscope. High-pressure-freezing was superior to other freezing protocols, because the whole bulk sample was reasonably well frozen and the overall three-dimensional shape of the embryos was well preserved. The samples were either dehydrated by freeze-substitution and critical-point-drying, or imaged in the partially hydrated state, using a cold stage in the SEM. During freeze-substitution the samples were stabilized by fixatives. The disadvantage of this method was that shrinking and extraction effects, caused by the removal of the water, could not be avoided. These disadvantages were avoided when the sample was imaged in the frozen-hydrated state using a cold-stage in the SEM. This would be the method of choice for morphometric studies. Frozen-hydrated samples, however, were very beam sensitive and many structures remained covered by the ice and were not visible. Frozen-hydrated samples were partially freeze-dried to make visible additional structures that had been covered by ice. However, this method also caused drying artifacts when too much water was removed.

Characterizing Martian Soils: Correlating Orbital Observations with Chemistry and Mineralogy from Landed Missions

NASA Astrophysics Data System (ADS)

Bishop, J. L.

2010-12-01

Great advances have been achieved recently in our understanding of the surface of Mars at global scales from orbital missions and at local scales from landed missions. This presentation seeks to provide links between the chemistry and mineralogy observed by landed missions with remote detections of minerals from orbit. Spectral data from CRISM, OMEGA and TES characterize a mostly basaltic planet with some outcrops of hematite, clays, sulfates and carbonates at the surface. Recent alteration of these rocks to form soils has likely been dominated by physical processes; however, martian soils probably also contain relicts of early alteration involving aqueous processes. Clays, hydroxides, sulfates, carbonates and perchlorates are examples of surface components that may have formed early in the planet’s history in the presence of liquid water. Some of these minerals have not been detected in the soil, but all have likely contributed to the current soil composition. The grain size, shape, chemistry, mineralogy, and magnetic properties of Martian soils are similar to altered volcanic ash found at many analog sites on Earth. Reflectance and emission spectra of some of these analog soils are consistent with the basic soil spectral properties observed from orbit. The cemented soil units observed by rovers may have formed through interaction of the soil grains with salts, clays, and hydroxides. Lab experiments have shown that cementing of analog grains darkens the VN reflectance, which could explain the low reflectance of Martian soils compared to analog sites. Reflectance spectra of an analog soil mixture containing altered ash and sulfate are shown in Figure 1. A pellet was made by adding water and allowing the sample to dry in air. Finally, the pellet was crushed and ground again to <125 µm. Both the dried pellet spectrum and the crushed pellet spectrum are darker than the original spectrum of the same composition. Erosion and weathering are likely the dominant processes forming the soils on Mars. However, reaction of surface grains with sulfates and perchlorates probably also influenced the soil grains. The perchlorates found by Phoenix are a strong oxidant. Consideration is being given to the interactions of perchlorates with minerals identified in surface rocks (pyroxene, olivine, feldspar, phyllosilicate, iron oxides, sulfate, silica, carbonate) and how perchlorates might be contributing to soil formation from these minerals and what their spectral properties might be.

Convective Heat Transfer from Castings of Ice Roughened Surfaces in Horizontal Flight

NASA Technical Reports Server (NTRS)

Dukhan, Nihad; Vanfossen, G. James, Jr.; Masiulaniec, K. Cyril; Dewitt, Kenneth J.

1995-01-01

A technique was developed to cast frozen ice shapes that had been grown on a metal surface. This technique was applied to a series of ice shapes that were grown in the NASA Lewis Icing Research Tunnel on flat plates. Eight different types of ice growths, characterizing different types of roughness, were obtained from these plates, from which aluminum castings were made. Test strips taken from these castings were outfitted with heat flux gages, such that when placed in a dry wind tunnel, they could be used to experimentally map out the convective heat transfer coefficient in the direction of flow from the roughened surfaces. The effects on the heat transfer coefficient for parallel flow, which simulates horizontal flight, were studied. The results of this investigation can be used to help size heaters for wings, helicopter rotor blades, jet engine intakes, etc., or de-icing for anti-icing applications where the flow is parallel to the iced surface.

Ice Slurry Ingestion Leads to a Lower Net Heat Loss during Exercise in the Heat.

PubMed

Morris, Nathan B; Coombs, Geoff; Jay, Ollie

2016-01-01

To compare the reductions in evaporative heat loss from the skin (Esk) to internal heat loss (Hfluid) induced by ice slurry (ICE) ingestion relative to 37 °C fluid and the accompanying body temperature and local thermoeffector responses during exercise in warm, dry conditions (33.5 °C ± 1.4 °C; 23.7% ± 2.6% relative humidity [RH]). Nine men cycled at approximately 55% VO2peak for 75 min and ingested 3.2 mL · kg(-1) aliquots of 37 °C fluid or ICE after 15, 30, and 45 min of exercise. Metabolic heat production (M-W), rectal temperature (Tre), mean skin temperature (Tsk), whole-body sweat loss (WBSL), local sweat rate (LSR), and skin blood flow (SkBF) were measured throughout. Net heat loss (HLnet) and heat storage (S) were estimated using partitional calorimetry. Relative to the 37 °C trial, M-W was similar (P = 0.81) with ICE ingestion; however, the 200 ± 20 kJ greater Hfluid (P < 0.001) with ICE ingestion was overcompensated by a 381 ± 199-kJ lower Esk (P < 0.001). Net heat loss (HLnet) was consequently 131 ± 120 kJ lower (P = 0.01) and S was greater (P = 0.05) with ICE ingestion compared with 37 °C fluid ingestion. Concurrently, LSR and WBSL were lower by 0.16 ± 0.14 mg · min(-1) · cm(-2) (P < 0.01) and 191 ± 122 g (P < 0.001), respectively, and SkBF tended to be lower (P = 0.06) by 5.4%maxAU ± 13.4%maxAU in the ICE trial. Changes in Tre and Tsk were similar throughout exercise with ICE compared to 37 °C fluid ingestion. Relative to 37 °C, ICE ingestion caused disproportionately greater reductions in Esk relative to Hfluid, resulting in a lower HLnet and greater S. Mechanistically, LSR and possibly SkBF were suppressed independently of Tre or Tsk, reaffirming the concept of human abdominal thermoreception. From a heat balance perspective, recommendations for ICE ingestion during exercise in warm, dry conditions should be reconsidered.

Ice nucleation rates of single protein complexes and single macromolecules

NASA Astrophysics Data System (ADS)

Stratmann, F.; Wex, H.; Niedermeier, D.; Hartmann, S.; Augustin, S.; Clauss, T.; Voigtlaender, J.; Pummer, B.; Grothe, H.

2012-12-01

With our flow-tube LACIS (Leipzig Aerosol cloud Interaction Simulator), we measured immersion freezing of droplets containing biological ice nucleating (IN) agents. From our measurements, we were able to deduce ice nucleation rates for single IN protein complexes (for Snomax) and for IN macromolecules (in the case of Birch pollen). For the measurements, aerosol particles were produced from solutions/suspensions of either Snomax (deadened and partly fractionalized pseudomonas syringae bacteria) or of Birch pollen washing water (BW in the following). All particles were dried and size selected before entering LACIS. In LACIS, particles were activated to droplets, and we measured the fraction of all droplets that froze (F(ice)) as function of temperature. For Snomax, a strong increase in F(ice) was observed around -7 to -10°C, for BW around -19 to -25°C, respectively. After this initial steep increase, F(ice) stayed constant for both examined substances down to -35°C. We found that the values of F(ice) in the plateau region depended on the dry particle size. The initial solution used to generate the particles contained parts of bacteria with ice active protein complexes on them in the case of Snomax, or IN macromolecules in the case of BW (Pummer et al., 2011). We show that the distribution of the IN proteins or IN molecules in the aerosol particles follows the Poisson distribution. With this knowledge, derivation of the ice nucleation rates for single IN protein complexes or for single IN macromolecules is possible. Combining the Poisson distribution with a stochastic model and using the derived nucleation rates, we can reproduce not only our measurements for both examined substances, but also past measurements done for Snomax and even pseudomonas syringae bacteria. As an additional peculiarity, we seem to observe two different macromolecules being ice active for Birch trees growing in Central Europe or Northern Europe, with the latter initiating freezing at slightly warmer temperatures. Pummer, B. G. et al. (2012), Suspendable macromolecules are responsible for ice nucleation activity of birch and conifer pollen, Aerosol Chem. Phys., 12, 2541-2550.

Effectiveness of bed bug monitors for detecting and trapping bed bugs in apartments.

PubMed

Wang, Changlu; Tsai, Wan-Tien; Cooper, Richard; White, Jeffrey

2011-02-01

Bed bugs, Cimex lectularius L., are now considered a serious urban pest in the United States. Because they are small and difficult to find, there has been strong interest in developing and using monitoring tools to detect bed bugs and evaluate the results of bed bug control efforts. Several bed bug monitoring devices were developed recently, but their effectiveness is unknown. We comparatively evaluated three active monitors that contain attractants: CDC3000, NightWatch, and a home-made dry ice trap. The Climbup Insect Interceptor, a passive monitor (without attractants), was used for estimating the bed bug numbers before and after placing active monitors. The results of the Interceptors also were compared with the results of the active monitors. In occupied apartments, the relative effectiveness of the active monitors was: dry ice trap > CDC3000 > NightWatch. In lightly infested apartments, the Interceptor (operated for 7 d) trapped similar number of bed bugs as the dry ice trap (operated for 1 d) and trapped more bed bugs than CDC3000 and NightWatch (operated for 1 d). The Interceptor was also more effective than visual inspections in detecting the presence of small numbers of bed bugs. CDC3000 and the dry ice trap operated for 1 d were equally as effective as the visual inspections for detecting very low level of infestations, whereas 1-d deployment of NightWatch detected significantly lower number of infestations compared with visual inspections. NightWatch was designed to be able to operate for several consecutive nights. When operated for four nights, NightWatch trapped similar number of bed bugs as the Interceptors operated for 10 d after deployment of NightWatch. We conclude these monitors are effective tools in detecting early bed bug infestations and evaluating the results of bed bug control programs.

Variations in Nutrient Cycling and Meltwater Composition Between Ice-Lidded and Open System Cryoconites

NASA Astrophysics Data System (ADS)

Mass, A.

2016-12-01

Cryoconites are small melt pools on the ablation surface of glaciers created by the accumulation of aeolian sediment with a lower albedo than the surrounding ice. While many cryoconites remain open to the surrounding atmosphere, environmental conditions in the McMurdo Dry Valleys of Antarctica often lead to the formation of dense ice lids due to advection from cold winds. These lidded cryoconites are isolated from atmospheric exchange while maintaining subsurface melt in a solid-state greenhouse. The varying conditions for the formation and freeze-thaw cycle of cryoconites lead to a range of biogeochemical processes occurring within the pools. This study analyzed the biochemistry of both open and lidded cryoconite water from six glaciers in the Dry Valleys throughout the initial pulse melt, equilibrium, and refreezing periods in 2013- 2015. Many of the spatial gradients in carbon cycling, solute concentrations, and pH identified for lidded cryoconites exhibited opposite trends for pools in equilibrium with the atmosphere, while temporal gradients were less diverse for open pools.

Exobiology site selection for future Mars missions: Martian paleolake sediments and terrestrial analogs

NASA Technical Reports Server (NTRS)

Wharton, Robert A., Jr.

1989-01-01

This research was conducted to establish the scientific framework for the exobiological study of sediments on Mars and to encourage the selection of these sedimentary deposits as sampling sites for future Mars missions. A study was completed on the Antarctic Dry Valley Lakes (terrestrial analogs of the purported Martian paleolakes) and their sediments that allowed the development of quantitative models relating environmental factors to the nature of the biological community and sediment forming processes. The publications presented include: (1) Diversity of micro-fungi isolated in an Antarctic dry valley; (2) Lake Hoare, Antarctica--sedimentation through a thick perennial ice cover; (3) The possibility of life on Mars during a water-rich past; (4) An Antarctic research outpost as a model for planetary exploration; (5) Early Martian environments--the Antarctic and other terrestrial analogs; (6) Lipophilic pigments from the benthos of a perennially ice-covered Antarctic lake; and (7) Perennially ice-covered Lake Hoare, Antarctica--physical environment, biology, and sedimentation.

Paleolakes and life on early Mars

NASA Technical Reports Server (NTRS)

Meyer, M. A.; Wharton, Robert A., Jr.; Mckay, C. P.

1991-01-01

Two distinct directions have begun to elucidate key parameters in the search for extinct life on Mars. Carbonate sediments, deposited about 10,000 years ago in association with biological activity, have been sampled from the paleolake beds of Lake Vanda and Meirs in the McMurdo Dry Valleys in Antarctica. These samples are being analyzed for simple biological signatures that remain in cold and dry paleolake sediments, namely microfossils, percent carbonate, and total organic carbon. Our second initiative is the study of Colour Lake, in the Canadian Arctic, that periodically maintains a perennial ice cover. Physical measurements started this year will be used to determine one end point for ice covered lake environments and will be compared to continuous measurements from Antarctic lakes started in November 1985. Interestingly, Colour Lake also supports benthic mat communities, but the low pH precludes carbonate deposition. This research will broaden our knowledge base for what conditions are necessary for ice covered lake formation and what biological signatures will remain in paleolake deposits.

Generation of Fullspan Leading-Edge 3D Ice Shapes for Swept-Wing Aerodynamic Testing

NASA Technical Reports Server (NTRS)

Camello, Stephanie C.; Lee, Sam; Lum, Christopher; Bragg, Michael B.

2016-01-01

The deleterious effect of ice accretion on aircraft is often assessed through dry-air flight and wind tunnel testing with artificial ice shapes. This paper describes a method to create fullspan swept-wing artificial ice shapes from partial span ice segments acquired in the NASA Glenn Icing Reserch Tunnel for aerodynamic wind-tunnel testing. Full-scale ice accretion segments were laser scanned from the Inboard, Midspan, and Outboard wing station models of the 65% scale Common Research Model (CRM65) aircraft configuration. These were interpolated and extrapolated using a weighted averaging method to generate fullspan ice shapes from the root to the tip of the CRM65 wing. The results showed that this interpolation method was able to preserve many of the highly three dimensional features typically found on swept-wing ice accretions. The interpolated fullspan ice shapes were then scaled to fit the leading edge of a 8.9% scale version of the CRM65 wing for aerodynamic wind-tunnel testing. Reduced fidelity versions of the fullspan ice shapes were also created where most of the local three-dimensional features were removed. The fullspan artificial ice shapes and the reduced fidelity versions were manufactured using stereolithography.

Map of Martian Polar Hydrogen

NASA Image and Video Library

2003-03-13

This gamma ray spectrometer map centered on the north pole of Mars is based on gamma-rays from the element hydrogen. In this region, hydrogen is mainly in the form of water ice. Regions of high ice content are shown in red and those low in ice content are shown in blue. The very ice-rich region at the north pole is due to a permanent polar cap of water ice on the surface. Elsewhere in this region, the ice is buried under several to a few tens of centimeters of dry soil. The sub-surface ice is not uniformly distributed in the north, but varies with both latitude and longitude. In the north, the soil is well over 50 percent ice, which is more than can be accommodated by just filling the pore space in pre-existing soil. This high ice content implies that the ice may have been slowly co-deposited with dust in the past when conditions were wetter. Deposition of ice by this process means it is more likely that the ice deposits are very thick and may even be deep enough to have liquid water at their base. http://photojournal.jpl.nasa.gov/catalog/PIA04254

A Synthesis of the Basal Thermal State of the Greenland Ice Sheet

NASA Technical Reports Server (NTRS)

Macgregor, J. A.; Fahnestock, M. A.; Catania, G. A.; Aschwanden, A.; Clow, G. D.; Colgan, W. T.; Gogineni, S. P.; Morlighem, M.; Nowicki, S. M. J.; Paden, J. D.;

Physicochemical properties of film-coated melt-extruded pellets.

PubMed

Young, Chistopher R; Crowley, Michael; Dietzsch, Caroline; McGinity, James W

2007-02-01

The purpose of this study was to investigate the physicochemical properties of poly(ethylene oxide) (PEO) and guaifenesin containing beads prepared by a melt-extrusion process and film-coated with a methacrylic acid copolymer. Solubility parameter calculations, thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), modulated differential scanning calorimetry (MDSC), X-ray powder diffraction (XRPD) and high performance liquid chromatography (HPLC) were used to determine drug/polymer miscibility and/or the thermal processibility of the systems. Powder blends of guaifenesin, PEO and functional excipients were processed using a melt-extrusion and spheronization technique and then film-coated in a fluidized bed apparatus. Solubility parameter calculations were used to predict miscibility between PEO and guaifenesin, and miscibility was confirmed by SEM and observation of a single melting point for extruded drug/polymer blends during MDSC investigations. The drug was stable following melt-extrusion as determined by TGA and HPLC; however, drug release rate from pellets decreased upon storage in sealed HDPE containers with silica desiccants at 40 degrees C/75% RH. The weight loss on drying, porosity and tortuosity determinations were not influenced by storage. Recrystallization of guaifenesin and PEO was confirmed by SEM and XRPD. Additionally, the pellets exhibited a change in adhesion behaviour during dissolution testing. The addition of ethylcellulose to the extruded powder blend decreased and stabilized the drug release rate from the thermally processed pellets. The current study also demonstrated film-coating to be an efficient process for providing melt-extruded beads with pH-dependent drug release properties that were stable upon storage at accelerated conditions.

Evidence of deep circulation in two perennially ice-covered Antarctic lakes

USGS Publications Warehouse

Tyler, S.W.; Cook, P.G.; Butt, A.Z.; Thomas, J.M.; Doran, P.T.; Lyons, W.B.

1998-01-01

The perennial ice covers found on many of the lakes in the McMurdo Dry Valley region of the Antarctic have been postulated to severely limit mixing and convective turnover of these unique lakes. In this work, we utilize chlorofluorocarbon (CFC) concentration profiles from Lakes Hoare and Fryxell in the McMurdo Dry Valley to determine the extent of deep vertical mixing occurring over the last 50 years. Near the ice-water interface, CFC concentrations in both lakes were well above saturation, in accordance with atmospheric gas supersaturations resulting from freezing under the perennial ice covers. Evidence of mixing throughout the water column at Lake Hoare was confirmed by the presence of CFCs throughout the water column and suggests vertical mixing times of 20-30 years. In Lake Fryxell, CFC-11, CFC-12, and CFC-113 were found in the upper water column; however, degradation of CFC-11 and CFC-12 in the anoxic bottom waters appears to be occurring with CFC-113 only present in these bottom waters. The presence of CFC-113 in the bottom waters, in conjunction with previous work detecting tritium in these waters, strongly argues for the presence of convective mixing in Lake Fryxell. The evidence for deep mixing in these lakes may be an important, yet overlooked, phenomenon in the limnology of perennially ice-covered lakes.

Improving Heat Transfer at the Bottom of Vials for Consistent Freeze Drying with Unidirectional Structured Ice.

PubMed

Rosa, Mónica; Tiago, João M; Singh, Satish K; Geraldes, Vítor; Rodrigues, Miguel A

2016-10-01

The quality of lyophilized products is dependent of the ice structure formed during the freezing step. Herein, we evaluate the importance of the air gap at the bottom of lyophilization vials for consistent nucleation, ice structure, and cake appearance. The bottom of lyophilization vials was modified by attaching a rectified aluminum disc with an adhesive material. Freezing was studied for normal and converted vials, with different volumes of solution, varying initial solution temperature (from 5°C to 20°C) and shelf temperature (from -20°C to -40°C). The impact of the air gap on the overall heat transfer was interpreted with the assistance of a computational fluid dynamics model. Converted vials caused nucleation at the bottom and decreased the nucleation time up to one order of magnitude. The formation of ice crystals unidirectionally structured from bottom to top lead to a honeycomb-structured cake after lyophilization of a solution with 4% mannitol. The primary drying time was reduced by approximately 35%. Converted vials that were frozen radially instead of bottom-up showed similar improvements compared with normal vials but very poor cake quality. Overall, the curvature of the bottom of glass vials presents a considerable threat to consistency by delaying nucleation and causing radial ice growth. Rectifying the vials bottom with an adhesive material revealed to be a relatively simple alternative to overcome this inconsistency.

Encapsulation of lactase in Ca(II)-alginate beads: Effect of stabilizers and drying methods.

PubMed

Traffano-Schiffo, Maria Victoria; Castro-Giraldez, Marta; Fito, Pedro J; Santagapita, Patricio R

2017-10-01

The purpose of the present work was to analyze the effect of trehalose, arabic and guar gums on the preservation of β-galactosidase activity in freeze-dried and vacuum dried Ca(II)-alginate beads. Freezing process was also studied as a first step of freeze-drying. Trehalose was critical for β-galactosidase conservation, and guar gum as a second excipient showed the highest conservation effect (close to 95%). Systems with T g values ~40°C which were stables at ambient temperature were obtained, being trehalose the main responsible of the formation of an amorphous matrix. Vacuum dried beads showed smaller size (with Feret's diameter below 1.08±0.09mm), higher circularity (reaching 0.78±0.06) and large cracks in their surface than freeze-dried beads, which were more spongy and voluminous. Ice crystallization of the beads revealed that the crystallization of Ca(II)-alginate system follows the Avrami kinetics of nucleation and growth. Particularly, Ca(II)-alginate showed an Avrami index of 2.03±0.07, which means that crystal growing is bidimensional. Neither the addition of trehalose nor gums affected the dimension of the ice growing or its rate. These results open an opportunity in the development of new lactic products able to be consumed by lactose intolerance people. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of differently structured and processed feedstuffs on diverse parameters of ethology and digestibility of growing rabbits and their influence on morphological structures in small intestine.

PubMed

Lang, Caroline; Hinchliffe, David; Brendle, Julia; Weirichl, Carmen; Hoy, Steffen

2016-01-01

The influence of different feedstuffs on parameters of digestion and ethology in growing rabbits (duration and number of feed intake, needed masticatory movements, pH value in stomach and small intestine, dry matter content of stomach chyme, level of destruction of cell structures in small intestine) was analysed. 384 five weeks old rabbits were fed with one of three feedstuffs: pellets (mean fibre length = 3 mm), fibre blocks (mean fibre length = 40 mm) and hay-oat-beat-ration (length of hay fibre ≥ 70 mm). The masticatory movements and duration for uptake 0.1 g of feedstuffs were measured in a special observation box. Rabbits in group cages were observed by 24 h video recording and duration and numbers of feed intakes were documented. After 8 weeks rabbits were slaughtered and pH values measured in stomach chyme (and dry matter content) and small intestine. Samples of them were taken and histologically examined (total length of villi and crypts, width of villi and degree of destruction determined by scores from 0 [= no destruction] to 3 [= severe destruction of villi]). Pellets lead to a faster feed intake with a lower number of masticatory movements. This equates a minor feeding time per feed intake and a higher amount of feedstuff in a shorter time. The dry matter content in stomach chyme increases and pH value was significantly higher there, but lower in duodenum. They also showed a significantly higher degree of destruction of villi, a shorter length and a larger width of villi than others.

Orange peel products can reduce Salmonella populations in ruminants.

PubMed

Callaway, Todd R; Carroll, Jeffery A; Arthington, John D; Edrington, Tom S; Anderson, Robin C; Rossman, Michelle L; Carr, Mandy A; Genovese, Ken J; Ricke, Steve C; Crandall, Phil; Nisbet, David J

2011-10-01

Salmonella can live undetected in the gut of food animals and be transmitted to humans. Animal diets can impact intestinal populations of foodborne pathogens, including Salmonella spp. Orange juice production results in a waste product, orange peel and orange pulp, which has a high nutritive value and is often included in cattle diets as a least-cost ration ingredient. Here we show that the inclusion of orange peel products reduced Salmonella Typhimurium populations in the gut of experimentally inoculated sheep. Sheep (n=24) were fed a cracked corn grain-based high grain diet that was supplemented with a 50%/50% (dry matter [DM], w/w) mixture of dried orange pellet and fresh orange peel to achieve a final concentration (DM, basis) of 0%, 10%, or 20% orange product (OP) for 10 days before inoculation with Salmonella Typhimurium. Sheep were experimentally inoculated with 10(10) colony forming units Salmonella Typhimurium, and fecal samples were collected every 24 h after inoculation. Sheep were humanely euthanized at 96 h after oral Salmonella inoculation. Populations of inoculated Salmonella Typhimurium were numerically reduced by OP treatment throughout the gastrointestinal tract, and this reduction only reached significant levels in the cecum (p<0.05) of sheep fed 10% OP diets. Apparent palatability issues decreased the consumption of OP in sheep fed 20% OP to intake levels below that of 10% OP (approximately 7% dry matter intake [DMI]/d feed refusal), thereby reducing the potential effects of OP feeding at this higher level. Our results demonstrate that orange peel and pellets are environmentally friendly and low-cost products that can be used as a pre-harvest intervention as part of an integrated pathogen reduction scheme.

Microwave-Assisted Alkali Pre-Treatment, Densification and Enzymatic Saccharification of Canola Straw and Oat Hull

PubMed Central

Agu, Obiora S.; Tabil, Lope G.; Dumonceaux, Tim

2017-01-01

The effects of microwave-assisted alkali pre-treatment on pellets’ characteristics and enzymatic saccharification for bioethanol production using lignocellulosic biomass of canola straw and oat hull were investigated. The ground canola straw and oat hull were immersed in distilled water, sodium hydroxide and potassium hydroxide solutions at two concentrations (0.75% and 1.5% w/v) and exposed to microwave radiation at power level 713 W and three residence times (6, 12 and 18 min). Bulk and particle densities of ground biomass samples were determined. Alkaline-microwave pre-treated and untreated samples were subjected to single pelleting test in an Instron universal machine, pre-set to a load of 4000 N. The measured parameters, pellet density, tensile strength and dimensional stability were evaluated and the results showed that the microwave-assisted alkali pre-treated pellets had a significantly higher density and tensile strength compared to samples that were untreated or pre-treated by microwave alone. The chemical composition analysis showed that microwave-assisted alkali pre-treatment was able to disrupt and break down the lignocellulosic structure of the samples, creating an area of cellulose accessible to cellulase reactivity. The best enzymatic saccharification results gave a high glucose yield of 110.05 mg/g dry sample for canola straw ground in a 1.6 mm screen hammer mill and pre-treated with 1.5% NaOH for 18 min, and a 99.10 mg/g dry sample for oat hull ground in a 1.6 mm screen hammer mill and pre-treated with 0.75% NaOH for 18 min microwave-assisted alkali pre-treatments. The effects of pre-treatment results were supported by SEM analysis. Overall, it was found that microwave-assisted alkali pre-treatment of canola straw and oat hull at a short residence time enhanced glucose yield. PMID:28952504

Evaluation of the systemic innate immune response and metabolic alterations of nonlactating cows with diet-induced subacute ruminal acidosis.

PubMed

Rodríguez-Lecompte, J C; Kroeker, A D; Ceballos-Márquez, A; Li, S; Plaizier, J C; Gomez, D E

2014-12-01

Subacute ruminal acidosis (SARA) increases lipopolysaccharide endotoxin in the rumen, which might translocate into the systemic circulation, triggering a cascade of clinical and immunological alterations. The objective of this study was to characterize the clinical immune and metabolic responses to ruminal-derived lipopolysaccharide in nonlactating cows induced with SARA using 2 challenges, a grain-based SARA challenge (GBSC) or an alfalfa-pellet SARA challenge (APSC). Six dry, nonlactating Holstein cows were used in a 3 × 3 Latin square arrangement of treatments with 4-wk experimental cycles. All cows received the control diet containing 70% forage and 30% mixed concentrates (dry matter basis) for 3 wk. In wk 4, cows received a control diet, GBSC (38% wheat-barley pellets, 32% other mixed concentrate, and 30% forages), or APSC (45% mixed concentrate, 32% alfalfa pellets, and 23% other forages). Total plasma proteins and immunology-related proteins, acute phase proteins, blood cells, serum chemistry, mRNA gene expression of peripheral blood cell surface markers, and selected proinflammatory cytokines were evaluated. Ruminal pH was lower in both groups with induced SARA compared with a control group. Ruminal endotoxins were higher in GBSC; however, plasma endotoxin was not detected in any study group. No significant differences in feed intake, rectal temperature, white blood cell counts, or differentials were found between control and SARA challenge groups; changes in glucose, urea, Ca, and Mg were observed in SARA groups. Total plasma proteins were lower in both SARA groups, and acute phase proteins were higher in GBSC. The expression of CD14, MD2, and TLR4 mRNA in peripheral blood leukocytes was not affected by SARA induction. The induction of SARA as a result of GBSC or APSC challenge was successful; however, LPS was not detected in plasma. Changes in clinical, metabolic, and inflammatory responses were not observed in the SARA-challenged cows, suggesting that, in this study, SARA was not associated with a systemic response to inflammation.

16 CFR 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) below the target temperature, remove the cooling block and quickly dry the cup with a paper tissue to... (cooling) fluid is solid carbon dioxide (dry ice) and acetone. If the refrigerant charged cooling module is... pouring acetone. Use only in a well-ventilated area. Avoid inhalation and contact with the eyes or skin...

Comparison of three different wastewater sludge and their respective drying processes: Solar, thermal and reed beds - Impact on organic matter characteristics.

PubMed

Collard, Marie; Teychené, Benoit; Lemée, Laurent

2017-12-01

Drying process aims at minimising the volume of wastewater sludge (WWS) before disposal, however it can impact sludge characteristics. Due to its high content in organic matter (OM) and lipids, sludge are mainly valorised by land farming but can also be considered as a feedstock for biodiesel production. As sludge composition is a major parameter for the choice of disposal techniques, the objective of this study was to determine the influence of the drying process. To reach this goal, three sludges obtained from solar, reed beds and thermal drying processes were investigated at the global and molecular scales. Before the drying step the sludges presented similar physico-chemical (OM content, elemental analysis, pH, infrared spectra) characteristics and lipid contents. A strong influence of the drying process on lipids and humic-like substances contents was observed through OM fractionation. Thermochemolysis-GCMS of raw sludge and lipids revealed similar molecular content mainly constituted with steroids and fatty acids. Molecular changes were noticeable for thermal drying through differences in branched to linear fatty acids ratio. Finally the thermal drying induced a weakening of OM whereas the solar drying led to a complexification. These findings show that smooth drying processes such as solar or reed-beds are preferable for amendment production whereas thermal process leads to pellets with a high lipid content which could be considered for fuel production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Probing Sub-atomistic Free-Volume Imperfections in Dry-Milled Nanoarsenicals with PAL Spectroscopy.

PubMed

Shpotyuk, Oleh; Ingram, Adam; Bujňáková, Zdenka; Baláž, Peter; Shpotyuk, Yaroslav

2016-12-01

Structural transformations caused by coarse-grained powdering and fine-grained mechanochemical milling in a dry mode were probed in high-temperature modification of tetra-arsenic tetra-sulfide known as β-As4S4. In respect to X-ray diffraction analysis, the characteristic sizes of β-As4S4 crystallites in these coarse- and fine-grained powdered pellets were 90 and 40 nm, respectively. Positron annihilation lifetime spectroscopy was employed to characterize transformations occurred in free-volume structure of these nanoarsenicals. Experimentally measured positron lifetime spectra were parameterized in respect to three- or two-term fitting procedures and respectively compared with those accumulated for single crystalline realgar α-As4S4 polymorph. The effect of coarse-grained powdering was found to result in generation of large amount of positron and positronium Ps trapping sites inside arsenicals in addition to existing ones. In fine-grained powdered β-As4S4 pellets, the positron trapping sites with characteristic free volumes close to bi- and tri-atomic vacancies were evidently dominated. These defects were supposed to originate from grain boundary regions and interfacial free volumes near aggregated β-As4S4 crystallites. Thus, the cumulative production of different positron traps with lifetimes close to defect-related lifetimes in realgar α-As4S4 polymorph was detected in fine-grained milled samples.

Ice Thermal Storage Systems for LWR Supplemental Cooling and Peak Power Shifting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haihua Zhao; Hongbin Zhang; Phil Sharpe

2010-06-01

Availability of enough cooling water has been one of the major issues for the nuclear power plant site selection. Cooling water issues have frequently disrupted the normal operation at some nuclear power plants during heat waves and long draught. The issues become more severe due to the new round of nuclear power expansion and global warming. During hot summer days, cooling water leaving a power plant may become too hot to threaten aquatic life so that environmental regulations may force the plant to reduce power output or even temporarily to be shutdown. For new nuclear power plants to be builtmore » at areas without enough cooling water, dry cooling can be used to remove waste heat directly into the atmosphere. However, dry cooling will result in much lower thermal efficiency when the weather is hot. One potential solution for the above mentioned issues is to use ice thermal storage systems (ITS) that reduce cooling water requirements and boost the plant’s thermal efficiency in hot hours. ITS uses cheap off-peak electricity to make ice and uses those ice for supplemental cooling during peak demand time. ITS is suitable for supplemental cooling storage due to its very high energy storage density. ITS also provides a way to shift large amount of electricity from off peak time to peak time. Some gas turbine plants already use ITS to increase thermal efficiency during peak hours in summer. ITSs have also been widely used for building cooling to save energy cost. Among three cooling methods for LWR applications: once-through, wet cooling tower, and dry cooling tower, once-through cooling plants near a large water body like an ocean or a large lake and wet cooling plants can maintain the designed turbine backpressure (or condensation temperature) during 99% of the time; therefore, adding ITS to those plants will not generate large benefits. For once-through cooling plants near a limited water body like a river or a small lake, adding ITS can bring significant economic benefits and avoid forced derating and shutdown during extremely hot weather. For the new plants using dry cooling towers, adding the ice thermal storage systems can effectively reduce the efficiency loss and water consumption during hot weather so that new LWRs could be considered in regions without enough cooling water. \\ This paper presents the feasibility study of using ice thermal storage systems for LWR supplemental cooling and peak power shifting. LWR cooling issues and ITS application status will be reviewed. Two ITS application case studies will be presented and compared with alternative options: one for once-through cooling without enough cooling for short time, and the other with dry cooling. Because capital cost, especially the ice storage structure/building cost, is the major cost for ITS, two different cost estimation models are developed: one based on scaling method, and the other based on a preliminary design using Building Information Modeling (BIM), an emerging technology in Architecture/Engineering/Construction, which enables design options, performance analysis and cost estimating in the early design stage.« less

Urey prize lecture - Water on Mars

NASA Technical Reports Server (NTRS)

Squyres, Steven W.

1989-01-01

Taking the heat-transport physics of ice-covered lakes in the Dry Valleys of Antarctica as a model, it is presently suggested that liquid water lakes could have persisted for significant periods under protective ice covers in the Valles Marineris depressions of Mars. Calculations of ground ice thermodynamic stability in a Martian setting indicate that they may exist close to the surface at high latitudes, but are able to persist near the equator only at substantial depths. Such Martian landforms as terrain-softening are attributable to the creep of the Martian regolith under the influence of ground-ice deformation; FEM modeling of the flow process implies terrain-softening to be a near-surface phenomenon.

Armed Forces Food Preferences

DTIC Science & Technology

1974-12-01

Breakfast Cereals 11 Griddle Cakes 12 Eggs 13 Breakfast Meats Arm®d Forces High Preference and Low Preference Foods HIGH Tom. Veg. Noodle Soup...Tomato Soup Chicken Noodle Soup Orange Juice Grape Juice Lemonade Iced Tea Milk Ice Cream Cola Doughnuts Sweet Rolls Cold Cereal Griddle...Grape Lemonade Lime-Flavored Drink Cherry-Flavored Drink Instant Coffee Freeze-Dried Coffee Skimmed Milk Buttermilk Frutt-Flvd. Yogurt Lo-cal

Formation and character of an ancient 19-m ice cover and underlying trapped brine in an "ice-sealed" east Antarctic lake.

PubMed

Doran, Peter T; Fritsen, Christian H; McKay, Christopher P; Priscu, John C; Adams, Edward E

2003-01-07

Lake Vida, one of the largest lakes in the McMurdo Dry Valleys of Antarctica, was previously believed to be shallow (<10 m) and frozen to its bed year-round. New ice-core analysis and temperature data show that beneath 19 m of ice is a water column composed of a NaCl brine with a salinity seven times that of seawater that remains liquid below -10 degrees C. The ice cover thickens at both its base and surface, sealing concentrated brine beneath. The ice cover is stabilized by a negative feedback between ice growth and the freezing-point depression of the brine. The ice cover contains frozen microbial mats throughout that are viable after thawing and has a history that extends to at least 2,800 (14)C years B.P., suggesting that the brine has been isolated from the atmosphere for as long. To our knowledge, Lake Vida has the thickest subaerial lake ice cover recorded and may represent a previously undiscovered end-member lacustrine ecosystem on Earth.

Formation and character of an ancient 19-m ice cover and underlying trapped brine in an “ice-sealed” east Antarctic lake

PubMed Central

Doran, Peter T.; Fritsen, Christian H.; McKay, Christopher P.; Priscu, John C.; Adams, Edward E.

2003-01-01

Lake Vida, one of the largest lakes in the McMurdo Dry Valleys of Antarctica, was previously believed to be shallow (<10 m) and frozen to its bed year-round. New ice-core analysis and temperature data show that beneath 19 m of ice is a water column composed of a NaCl brine with a salinity seven times that of seawater that remains liquid below −10°C. The ice cover thickens at both its base and surface, sealing concentrated brine beneath. The ice cover is stabilized by a negative feedback between ice growth and the freezing-point depression of the brine. The ice cover contains frozen microbial mats throughout that are viable after thawing and has a history that extends to at least 2,800 14C years B.P., suggesting that the brine has been isolated from the atmosphere for as long. To our knowledge, Lake Vida has the thickest subaerial lake ice cover recorded and may represent a previously undiscovered end-member lacustrine ecosystem on Earth. PMID:12518052

Properties of Filamentary Sublimation Residues from Dispersions of Clay in Ice

NASA Technical Reports Server (NTRS)

Stephens, J. B.; Parker, T. J.; Saunders, R. S.; Laue, E. G.; Fanale, F. P.

1985-01-01

The properties of sublimate residues are of considerable interest in studies of the thermal modeling of Martian and cometary ice surfaces. The study of the formation of sand grains from this mantle on Martian polar ice is also supported by these experiments. To understand these properties, a series of low temperature vacuum experiments were run during which dirty ices that might be expected to be found in Martian polar caps and in comet nuclei were made and then freeze dried. In addition to using particulate material of appropriate grain size and minerology, particle nucleated ices were simulated by dispersing the particulates in the ice so that they did not contact one another. This noncontact dispersion was the most difficult requirement to achieve but the most rewarding in that it produced a new filamentary sublimate residue that was not a relic of the frozen dispersion. If the siliceous particles are allowed to touch one another in the ice the structure of the contacting particles in the ice will remain as a relic after the ice is sublimed away.

Ice nucleation activity of diesel soot particles at cirrus relevant temperature conditions: Effects of hydration, secondary organics coating, soot morphology, and coagulation

NASA Astrophysics Data System (ADS)

Kulkarni, Gourihar; China, Swarup; Liu, Shang; Nandasiri, Manjula; Sharma, Noopur; Wilson, Jacqueline; Aiken, Allison C.; Chand, Duli; Laskin, Alexander; Mazzoleni, Claudio; Pekour, Mikhail; Shilling, John; Shutthanandan, Vaithiyalingam; Zelenyuk, Alla; Zaveri, Rahul A.

2016-04-01

Ice formation by diesel soot particles was investigated at temperatures ranging from -40 to -50°C. Size-selected soot particles were physically and chemically aged in an environmental chamber, and their ice nucleating properties were determined using a continuous flow diffusion type ice nucleation chamber. Bare (freshly formed), hydrated, and compacted soot particles, as well as α-pinene secondary organic aerosol (SOA)-coated soot particles at high relative humidity conditions, showed ice formation activity at subsaturation conditions with respect to water but below the homogeneous freezing threshold conditions. However, SOA-coated soot particles at dry conditions were observed to freeze at homogeneous freezing threshold conditions. Overall, our results suggest that heterogeneous ice nucleation activity of freshly emitted diesel soot particles are sensitive to some of the aging processes that soot can undergo in the atmosphere.

Physicochemical, bioactive, and sensory properties of persimmon-based ice cream: technique for order preference by similarity to ideal solution to determine optimum concentration.

PubMed

Karaman, Safa; Toker, Ömer Said; Yüksel, Ferhat; Çam, Mustafa; Kayacier, Ahmed; Dogan, Mahmut

2014-01-01

In the present study, persimmon puree was incorporated into the ice cream mix at different concentrations (8, 16, 24, 32, and 40%) and some physicochemical (dry matter, ash, protein, pH, sugar, fat, mineral, color, and viscosity), textural (hardness, stickiness, and work of penetration), bioactive (antiradical activity and total phenolic content), and sensory properties of samples were investigated. The technique for order preference by similarity to ideal solution approach was used for the determination of optimum persimmon puree concentration based on the sensory and bioactive characteristics of final products. Increase in persimmon puree resulted in a decrease in the dry matter, ash, fat, protein contents, and viscosity of ice cream mix. Glucose, fructose, sucrose, and lactose were determined to be major sugars in the ice cream samples including persimmon and increase in persimmon puree concentration increased the fructose and glucose content. Better melting properties and textural characteristics were observed for the samples with the addition of persimmon. Magnesium, K, and Ca were determined to be major minerals in the samples and only K concentration increased with the increase in persimmon content. Bioactive properties of ice cream samples improved and, in general, acetone-water extracts showed higher bioactivity compared with ones obtained using methanol-water extracts. The technique for order preference by similarity to ideal solution approach showed that the most preferred sample was the ice cream containing 24% persimmon puree. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Environmentally Non-Disturbing Under-ice Robotic ANtarctiC Explorer (ENDURANCE)

NASA Astrophysics Data System (ADS)

Doran, P. T.; Stone, W.; Priscu, J.; McKay, C.; Johnson, A.; Chen, B.

2007-12-01

Permanently ice-covered liquid water environments are among the leading candidate sites for finding evidence of extant life elsewhere in our solar system (e.g. on Europa and other Galiean satellites, and possibly in subglacial lakes on Mars). In order to have the proper tools and strategies for exploring the extant ice-covered planetary environments, we are developing an autonomous underwater vehicle (AUV) capable of generating for the first time 3-D biogeochemical datasets in the extreme environment of perennially ice-covered Antarctic dry valley lakes. The ENDURANCE (Environmentally Non-Disturbing Under-ice Robotic ANtarctic Explorer) will map the under-ice lake dimensions of West Lake Bonney in the McMurdo Dry Valleys, and be equipped to measure a comprehensive suite of physical and biogeochemical indices in the water column, as well as Raman Spectrometry of the water column and benthos. The AUV is being specifically designed to minimize impact on the environment it is working in. This is primarily to meet strict Antarctic environmental protocols, but will also be useful for planetary protection and improved science in the future. We will carry out two Antarctic field seasons (in concert with our NSF-funded Long Term Ecological Research) and test two central hypotheses: H1: The low kinetic energy of the system (diffusion dominates the spatial transport of constituents) produces an ecosystem and ecosystem limits that vary significantly in three dimensions. H2: The whole-lake physical and biogeochemical structure remains static from year to year The talk will provide an overview of the ENDURANCE project and an update on the AUV development at the time of presentation.

Microbiota within the perennial ice cover of Lake Vida, Antarctica.

PubMed

Mosier, Annika C; Murray, Alison E; Fritsen, Christian H

2007-02-01

Lake Vida, located in the McMurdo Dry Valleys, Antarctica, is an 'ice-sealed' lake with approximately 19 m of ice covering a highly saline water column (approximately 245 ppt). The lower portions of the ice cover and the lake beneath have been isolated from the atmosphere and land for circa 2800 years. Analysis of microbial assemblages within the perennial ice cover of the lake revealed a diverse array of bacteria and eukarya. Bacterial and eukaryal denaturing gradient gel electrophoresis phylotype profile similarities were low (<59%) between all of the depths compared (five depths spanning 11 m of the ice cover), with the greatest differences occurring between surface and deep ice. The majority of bacterial 16S rRNA gene sequences in the surface ice were related to Actinobacteria (42%) while Gammaproteobacteria (52%) dominated the deep ice community. Comparisons of assemblage composition suggest differences in ice habitability and organismal origin in the upper and lower portions of ice cover. Specifically, the upper ice cover microbiota likely reflect the modern day transport and colonization of biota from the terrestrial landscape, whereas assemblages in the deeper ice are more likely to be persistent remnant biota that originated from the ancient liquid water column of the lake that froze.

Solubility parameters of hypromellose acetate succinate and plasticization in dry coating procedures.

PubMed

Klar, Fabian; Urbanetz, Nora Anne

2016-10-01

Solubility parameters of HPMCAS have not yet been investigated intensively. On this account, total and three-dimensional solubility parameters of HPMCAS were determined by using different experimental as well as computational methods. In addition, solubility properties of HPMCAS in a huge number of solvents were tested and a Teas plot for HPMCAS was created. The total solubility parameter of about 24 MPa(0.5) was confirmed by various procedures and compared with values of plasticizers. Twenty common pharmaceutical plasticizers were evaluated in terms of their suitability for supporting film formation of HPMCAS under dry coating conditions. Therefore, glass transition temperatures of mixtures of polymer and plasticizers were inspected and film formation of potential ones was further investigated in dry coating of pellets. Contact angles of plasticizers on HPMCAS were determined in order to give a hint of achievable coating efficiencies in dry coating, but none was found to spread on HPMCAS. A few common substances, e.g. dimethyl phthalate, glycerol monocaprylate, and polyethylene glycol 400, enabled plasticization of HPMCAS; however, only triethyl citrate and triacetin were found to be suitable for use in dry coating. Addition of acetylated monoglycerides to triacetin increased coating efficiency, which was likewise previously demonstrated for triethyl citrate.

Hydroxypropyl-ß-cyclodextrin as a membrane protectant during freeze-drying of hydrogenated and non-hydrogenated liposomes and molecule-in-cyclodextrin-in- liposomes: Application to trans-anethole.

PubMed

Gharib, Riham; Greige-Gerges, Hélène; Fourmentin, Sophie; Charcosset, Catherine

2018-11-30

The effect of hydrogenation of phospholipids on the characteristics of freeze-dried liposomes was investigated using hydroxypropyl-ß-cyclodextrin (HP-ß-CD) as membrane protectant. The ethanol-injection method was applied to prepare liposomes using hydrogenated (Phospholopion-90H and 80H) and non-hydrogenated phospholipids (Lipoid-S100) in combination with cholesterol. Various liposomal formulations were tested: conventional liposomes (CL) and HP-ß-CD-loaded liposomes (CDL). Liposome suspensions were concentrated by ultracentrifugation; the pellets were reconstituted in water or CD solution and the dispersions were characterized for their size, polydispersity index and zeta potential. Results demonstrated that HP-ß-CD protected only the hydrogenated batches (CL and CDL) during freeze-drying. Moreover, the presence of HP-ß-CD in the aqueous phase of CDL protected them during freeze-drying. Freeze-dried CL and CDL made of phospholipon-90H loading anethole were demonstrated to be physically stable upon reconstitution in HP-ß-CD solutions, and are able to retain anethole after 6 months of storage at 4 °C thereby making them valuable for food applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Testing the Late Noachian Icy Highlands Model: Geological Observations, Processes and Origin of Fluvial and Lacustrine Features.

NASA Astrophysics Data System (ADS)

Head, James; Wordsworth, Robin; Forget, Francis; Madeleine, Jean-Baptiste; Halvey, Italy

2014-05-01

A new reconstruction of the Late Noachian Mars atmosphere and climate shows atmosphere-surface thermal coupling and an adiabatic cooling effect producing preferential distribution of snow and ice in the highlands. In this Late Noachian Icy Highlands (LNIH) scenario, snow and ice accumulate in the south circumpolar region and in the higher altitudes of the southern uplands, but the mean annual temperature is everywhere below freezing. How can the abundant evidence for water-related fluvial and lacustrine activity (valley networks, VN; open-basin lakes, OBL; closed-basin lakes; CBL) be reconciled with the icy highlands model? We investigate the nature of geologic processes operating in the icy highlands and use the Antarctic McMurdo Dry Valleys (MDV) as guidance in understanding and assessing how melting might be taking place. In the MDV, mean annual temperatures (MAT) are well below freezing. This results in a thick regional permafrost layer, the presence of an ice-table at shallow depths, and an overlying dry active layer. This configuration produces a perched aquifer and a horizontally stratified hydrologic system, where any melting results in local saturation of the dry active layer and channelized flow on top of the ice table. Top-down melting results in the dominance of lateral water transport, in contrast to temperate climates with vertical infiltration and transport to the groundwater table. Despite subzero MAT, MDV peak seasonal and peak daytime temperatures can exceed 273K and have a strong influence on the melting of available water ice. We present maps of the predicted distribution of LNIH snow and ice, compare these to the distribution of VN, OBL and CBL, and assess how top-down and bottom-up melting processes might explain the formation of these features in an otherwise cold and icy LN Mars. We assess the global near-surface water budget, analyze thickness estimates to distinguish areas of cold-based and wet-based glaciation, analyze the state of the ice cover and its susceptibility to melting and runoff, and describe top-down melting and fluvial channel formation processes in a LNIH environment. We find that: 1) episodic top-down melting of the LNIH is a robust mechanism to produce the observed fluvial and lacustrine features; 2) the characteristics and distribution of features in the Dorsa Argentea Formation are consistent with an extensive circum-polar ice cap during LNIH time; and 3) the nature of preserved LN impact craters is consistent with impact cratering processes in the LNIH environment. 393 words.

Effects of morphology parameters on anti-icing performance in superhydrophobic surfaces

NASA Astrophysics Data System (ADS)

Nguyen, Thanh-Binh; Park, Seungchul; Lim, Hyuneui

2018-03-01

In this paper, we report the contributions of actual ice-substrate contact area and nanopillar height to passive anti-icing performance in terms of adhesion force and freezing time. Well-textured nanopillars with various parameters were fabricated via colloidal lithography and a dry etching process. The nanostructured quartz surface was coated with low-energy material to confer water-repellent properties. These superhydrophobic surfaces were investigated to determine the parameters essential for reducing adhesion strength and delaying freezing time. A well-textured surface with nanopillars of very small top diameter, regardless of height, could reduce adhesion force and delay freezing time in a subsequent de-icing process. Small top diameters of nanopillars also ensured the metastable Cassie-Baxter state based on energy barrier calculations. The results demonstrated the important role of areal fraction in anti-icing efficiency, and the negligible contribution of texture height. This insight into icing phenomena should lead to design of improved ice-phobic surfaces in the future.

The role of water ice clouds in the Martian hydrologic cycle

NASA Technical Reports Server (NTRS)

James, Philip B.

1990-01-01

A one-dimensional model for the seasonal cycle of water on Mars has been used to investigate the direction of the net annual transport of water on the planet and to study the possible role of water ice clouds, which are included as an independent phase in addition to ground ice and water vapor, in the cycle. The calculated seasonal and spatial patterns of occurrence of water ice clouds are qualitatively similar to the observed polar hoods, suggesting that these polar clouds are, in fact, an important component of water cycle. A residual dry ice in the south acts as a cold trap which, in the absence of sources other than the caps, will ultimately attract the water ice from the north cap; however, in the presence of a source of water in northern midlatitudes during spring, it is possible that the observed distribution of vapor and ice can be in a steady state even if a residual CO2 cap is a permanent feature of the system.

Collisions with ice-volatile objects: Geological implications

NASA Technical Reports Server (NTRS)

Wilde, P.; Quinby-Hunt, M. S.; Berry, W. B. N.

1988-01-01

The collision of the Earth with extra-terrestrial ice-volatile bodies is proposed as a mechanism to produce rapid changes in the geologic record. These bodies would be analogs of the ice satellites found for the Jovian planets and suspected for comets and certain low density bodies in the Asteroid belt. Five generic end-members are postulated: (1) water ice; (2) dry ice: carbon-carbon dioxide rich, (3) oceanic (chloride) ice; (4) sulfur-rich ice; (5) ammonia hydrate-rich ice; and (6) clathrate: methane-rich ice. Due to the volatile nature of these bodies, evidence for their impact with the Earth would be subtle and probably best reflected geochemically or in the fossil record. Actual boloids impacting the Earth may have a variable composition, generally some admixture with water ice. However for discussion purposes, only the effects of a dominant component will be treated. The general geological effects of such collisions, as a function of the dominant component would be: (1) rapid sea level rise unrelated to deglaciation, (2) decreased oceanic pH and rapid climatic warming or deglaciation; (3) increased paleosalinities; (4) increased acid rain; (5) increased oceanic pH and rapid carbonate deposition; and (6) rapid climatic warming or deglaciation.

Depth, ice thickness, and ice-out timing cause divergent hydrologic responses among Arctic lakes

USGS Publications Warehouse

Arp, Christopher D.; Jones, Benjamin M.; Liljedahl, Anna K.; Hinkel, Kenneth M.; Welker, Jeffery A.

2015-01-01

Lakes are prevalent in the Arctic and thus play a key role in regional hydrology. Since many Arctic lakes are shallow and ice grows thick (historically 2-m or greater), seasonal ice commonly freezes to the lake bed (bedfast ice) by winter's end. Bedfast ice fundamentally alters lake energy balance and melt-out processes compared to deeper lakes that exceed the maximum ice thickness (floating ice) and maintain perennial liquid water below floating ice. Our analysis of lakes in northern Alaska indicated that ice-out of bedfast ice lakes occurred on average 17 days earlier (22-June) than ice-out on adjacent floating ice lakes (9-July). Earlier ice-free conditions in bedfast ice lakes caused higher open-water evaporation, 28% on average, relative to floating ice lakes and this divergence increased in lakes closer to the coast and in cooler summers. Water isotopes (18O and 2H) indicated similar differences in evaporation between these lake types. Our analysis suggests that ice regimes created by the combination of lake depth relative to ice thickness and associated ice-out timing currently cause a strong hydrologic divergence among Arctic lakes. Thus understanding the distribution and dynamics of lakes by ice regime is essential for predicting regional hydrology. An observed regime shift in lakes to floating ice conditions due to thinner ice growth may initially offset lake drying because of lower evaporative loss from this lake type. This potential negative feedback caused by winter processes occurs in spite of an overall projected increase in evapotranspiration as the Arctic climate warms.

Effects of vial packing density on drying rate during freeze-drying of carbohydrates or a model protein measured using a vial-weighing technique.

PubMed

Gieseler, Henning; Lee, Geoffrey

2008-02-01

To determine the effects of vial packing density in a laboratory freeze dryer on drying rate profiles of crystalline and amorphous formulations. The Christ freeze-drying balance measured cumulative water loss, m(t), and instantaneous drying rate, m(t), of water, mannitol, sucrose and sucrose/BSA formulations in commercial vials. Crystalline mannitol shows drying rate behaviour indicative of a largely homogeneous dried-product layer. The drying rate behaviour of amorphous sucrose indicates structural heterogeneity, postulated to come from shrinkage or microcollapse. Trehalose dries more slowly than sucrose. Addition of BSA to either disaccharide decreases primary drying time. Higher vial packing density greatly reduces drying rate because of effects of radiation heat transfer from chamber walls to test vial. Plots of m(t) versus radical t and m(t) versus layer thickness (either ice or dried-product) allow interpretation of changes in internal cake morphology during drying. Vial packing density greatly influences these profiles.

Interaction between the physical form of the starter feed and straw provision on growth performance of Holstein calves.

PubMed

Terré, M; Castells, Ll; Khan, M A; Bach, A

2015-02-01

Two experiments were conducted to assess the effect of physical form of a starter feed with or without straw supplementation on growth performance of Holstein calves. In experiment 1, a total of 32 calves were randomly assigned at 7 d of age to texturized starter feed (containing rolled barley, corn, and oats) without straw, texturized starter feed with chopped straw, and pelleted starter feed with chopped straw. All calves were offered 4 L of pasteurized whole milk twice daily from 7 to 35 d of age, 2 L of milk twice daily from 36 to 42 d of age, and 2 L of milk from 43 to 49 d of age. Animals were weaned at 50 d of age, and the study finished when calves were 63 d old. In experiment 2, a total of 60 calves (8 d of age) were randomly assigned to texturized starter feed (containing whole corn) without straw, pelleted starter feed without straw, and pelleted starter feed with chopped straw. All calves were offered the same milk replacer (MR; 23% crude protein and 19.5 fat) at 11% dry matter concentration, 4 L/d of MR until 14 d of age, 6 L/d of MR from 14 to 37 d, 3 L/d of MR from 38 to 44 d, and 1.5 L/d of MR from 45 to 52 d of age. The experiment finished when calves were 58 d old (1 wk after weaning). Rumen liquid pH was measured after weaning. In both studies, calves were individually housed in pens on sawdust bedding and starter feed and chopped straw were offered free choice in separate buckets. In experiment 1, starter feed and straw intake and growth did not differ among treatments. However, calves receiving straw showed a greater rumen pH compared with those not receiving straw. In experiment 2, pelleted started feed supplemented with straw fostered an increase in solid feed intake (as percentage of body weight) compared with a pelleted or texturized starter feed without straw supplementation. However, calves that received the texturized starter feed containing whole corn had rumen pH similar to those fed a pelleted starter feed with straw. Feeding a texturized starter feed containing rolled barley, corn, and oats (with or without straw provision) was not able to maintain rumen pH or promote growth and intake compared with offering a pelleted starter feed with chopped straw. However, when whole corn was used in the texturized starter feed, rumen pH was equivalent to that obtained with a pelleted starter feed and straw supplementation. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Spectral Analysis and Experimental Modeling of Ice Accretion Roughness

NASA Technical Reports Server (NTRS)

Orr, D. J.; Breuer, K. S.; Torres, B. E.; Hansman, R. J., Jr.

1996-01-01

A self-consistent scheme for relating wind tunnel ice accretion roughness to the resulting enhancement of heat transfer is described. First, a spectral technique of quantitative analysis of early ice roughness images is reviewed. The image processing scheme uses a spectral estimation technique (SET) which extracts physically descriptive parameters by comparing scan lines from the experimentally-obtained accretion images to a prescribed test function. Analysis using this technique for both streamwise and spanwise directions of data from the NASA Lewis Icing Research Tunnel (IRT) are presented. An experimental technique is then presented for constructing physical roughness models suitable for wind tunnel testing that match the SET parameters extracted from the IRT images. The icing castings and modeled roughness are tested for enhancement of boundary layer heat transfer using infrared techniques in a "dry" wind tunnel.

Distribution of glacial deposits, soils, and permafrost in Taylor Valley, Antarctica

USGS Publications Warehouse

Bockheim, James G.; Prentice, M.L.; McLeod, M.

2008-01-01

We provide a map of lower and central Taylor Valley, Antarctica, that shows deposits from Taylor Glacier, local alpine glaciers, and grounded ice in the Ross Embayment. From our electronic database, which includes 153 sites from the coast 50 km upvalley to Pearse Valley, we show the distribution of permafrost type and soil subgroups according to Soil Taxonomy. Soils in eastern Taylor Valley are of late Pleistocene age, cryoturbated due to the presence of ground ice or ice-cemented permafrost within 70 cm of the surface, and classified as Glacic and Typic Haploturbels. In central Taylor Valley, soils are dominantly Typic Anhyorthels of mid-Pleistocene age that have dry-frozen permafrost within the upper 70 cm. Salt-enriched soils (Salic Anhyorthels and Petrosalic Anhyorthels) are of limited extent in Taylor Valley and occur primarily on drifts of early Pleistocene and Pliocene age. Soils are less developed in Taylor Valley than in nearby Wright Valley, because of lesser salt input from atmospheric deposition and salt weathering. Ice-cemented permafrost is ubiquitous on Ross Sea, pre-Ross Sea, and Bonney drifts that occur within 28 km of the McMurdo coast. In contrast, dry-frozen permafrost is prevalent on older (???115 ky) surfaces to the west. ?? 2008 Regents of the University of Colorado.

Empirical Retrieval of Surface Melt Magnitude from Coupled MODIS Optical and Thermal Measurements over the Greenland Ice Sheet during the 2001 Ablation Season

PubMed Central

Lampkin, Derrick; Peng, Rui

2008-01-01

Accelerated ice flow near the equilibrium line of west-central Greenland Ice Sheet (GIS) has been attributed to an increase in infiltrated surface melt water as a response to climate warming. The assessment of surface melting events must be more than the detection of melt onset or extent. Retrieval of surface melt magnitude is necessary to improve understanding of ice sheet flow and surface melt coupling. In this paper, we report on a new technique to quantify the magnitude of surface melt. Cloud-free dates of June 10, July 5, 7, 9, and 11, 2001 Moderate Resolution Imaging Spectroradiometer (MODIS) daily reflectance Band 5 (1.230-1.250μm) and surface temperature images rescaled to 1km over western Greenland were used in the retrieval algorithm. An optical-thermal feature space partitioned as a function of melt magnitude was derived using a one-dimensional thermal snowmelt model (SNTHERM89). SNTHERM89 was forced by hourly meteorological data from the Greenland Climate Network (GC-Net) at reference sites spanning dry snow, percolation, and wet snow zones in the Jakobshavn drainage basin in western GIS. Melt magnitude or effective melt (E-melt) was derived for satellite composite periods covering May, June, and July displaying low fractions (0-1%) at elevations greater than 2500m and fractions at or greater than 15% at elevations lower than 1000m assessed for only the upper 5 cm of the snow surface. Validation of E-melt involved comparison of intensity to dry and wet zones determined from QSCAT backscatter. Higher intensities (> 8%) were distributed in wet snow zones, while lower intensities were grouped in dry zones at a first order accuracy of ∼ ±2%. PMID:27873793

Empirical Retrieval of Surface Melt Magnitude from Coupled MODIS Optical and Thermal Measurements over the Greenland Ice Sheet during the 2001 Ablation Season.

PubMed

Lampkin, Derrick; Peng, Rui

2008-08-22

Accelerated ice flow near the equilibrium line of west-central Greenland Ice Sheet (GIS) has been attributed to an increase in infiltrated surface melt water as a response to climate warming. The assessment of surface melting events must be more than the detection of melt onset or extent. Retrieval of surface melt magnitude is necessary to improve understanding of ice sheet flow and surface melt coupling. In this paper, we report on a new technique to quantify the magnitude of surface melt. Cloud-free dates of June 10, July 5, 7, 9, and 11, 2001 Moderate Resolution Imaging Spectroradiometer (MODIS) daily reflectance Band 5 (1.230-1.250μm) and surface temperature images rescaled to 1km over western Greenland were used in the retrieval algorithm. An optical-thermal feature space partitioned as a function of melt magnitude was derived using a one-dimensional thermal snowmelt model (SNTHERM89). SNTHERM89 was forced by hourly meteorological data from the Greenland Climate Network (GC-Net) at reference sites spanning dry snow, percolation, and wet snow zones in the Jakobshavn drainage basin in western GIS. Melt magnitude or effective melt (E-melt) was derived for satellite composite periods covering May, June, and July displaying low fractions (0-1%) at elevations greater than 2500m and fractions at or greater than 15% at elevations lower than 1000m assessed for only the upper 5 cm of the snow surface. Validation of E-melt involved comparison of intensity to dry and wet zones determined from QSCAT backscatter. Higher intensities (> 8%) were distributed in wet snow zones, while lower intensities were grouped in dry zones at a first order accuracy of ~ ±2%.

Refuse-Derived Fuels in U.S. Air Force Heating and Power Systems.

DTIC Science & Technology

1986-01-01

pellet degradation . Postpellet - cooling may not prevent disintegration into more fines. The Argonne W National Laboratory is sponsoring a research...of fuel,% by using the fuel Orsat (volumetric) analysis and both the carbon and sulfur in the fuel. This is known as a carbon balance. 00 The test... sulfur in the fuel per pound of fuel C ’ = average specific heat of the dry flue gas PG T = flue gas temperature leaving the economizer (or leaving

Fuel agglomerates and method of agglomeration

DOEpatents

Wen, Wu-Wey

1986-01-01

Solid fuel agglomerates are prepared of particulate coal or other carbonaceous material with a binder having a high humic acid or humate salt content. The humic acid is extracted from oxidized carbonaceous material with a mild aqueous alkali solution of, for instance, ammonia. The particulate material is blended with the extract which serves as the binder for the agglomerates. The water-resistant agglomerates are formed such as by pelletizing, followed by drying to remove moisture and solidify the humic acid binder throughout the agglomerate.

Radiochemical purity, at expiry, and radiochemical stability of iodine-131 labelled meta-iodobenzylguanidine concentrates for intravenous infusion.

PubMed

Wafelman, A R; Hoefnagel, C A; Maes, R A; Beijnen, J H

1996-08-01

The determination of the amount of free [131I]iodide in [131I]metaiodobenzylguanidine ([131I]MIBG) concentrates for intravenous infusion under different storage conditions derived from daily practice. The percentage of free [131I]iodide was determined in [131I]MIBG concentrates (1.6-3.9 GBq in 7.5 ml), kept on dry ice (up to expiry, 3 days after production) or, after thawing, at room temperature (up to 24 h). A validated solid phase extraction (SPE) assay was used. Free [131I]iodide increased from 1.9% +/- 0.34% at production to 4.4% +/- 0.67% (mean +/- SD; n = 5) at expiry in 3.7 GBq per 7.5 ml [131I]MIBG infusion concentrates stored on dry ice (-78 degrees C). At room temperature, formation of free [131I]iodide was found to be dependent on the radioactive concentration of the fluid. [131I]iodide levels increased from 3.1%, immediately after thawing, to 6.6% and 16.6% at t = 5 and 24 h, respectively, for a 3.9 GBq per 7.5 ml concentrate. The investigated formulation of [131I]MIBG concentrates, stored in its original packing containing dry ice, can generally be used up to expiry. After thawing, the undiluted concentrates should be administered to a patient within 3.5 h.

Classification of Baltic Sea ice types by airborne multifrequency microwave radiometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurvonen, L.; Hallikainen, M.

An airborne multifrequency radiometer (24, 34, 48, and 94 GHz, vertical polarization) was used to investigate the behavior of the brightness temperature of different sea ice types in the Gulf of Bothnia (Baltic Sea). The measurements and the main results of the analysis are presented. The measurements were made in dry and wet conditions (air temperature above and below 0 C). The angle of incidence was 45{degree} in all measurements. The following topics are evaluated: (a) frequency dependency of the brightness temperature of different ice types, (b) the capability of the multifrequency radiometer to classify ice types for winter navigationmore » purposes, and (c) the optimum measurement frequencies for mapping sea ice. The weather conditions had a significant impact on the radiometric signatures of some ice types (snow-covered compact pack ice and frost-covered new ice); the impact was the highest at 94 GHz. In all cases the overall classification accuracy was around 90% (the kappa coefficient was from 0.86 to 0.96) when the optimum channel combination (24/34 GHz and 94 GHz) was used.« less

Molecular Markers in the Quelccaya Ice Cap, Peru Describe 20th Century Biomass Burning Variability

NASA Astrophysics Data System (ADS)

Makou, M. C.; Thompson, L. G.; Eglinton, T. I.; Montluçon, D. B.

2007-12-01

Organic geochemical analytical methods were applied to Andean ice core samples, resulting in a multi- molecular biomass burning record spanning 1915 to 2001 AD. The Quelccaya Ice Cap in Peru is situated on the eastern flank of the Andes at 14°S and is well situated to receive aeolian inputs of organic matter derived from Amazonian forest fire events. Compounds of interest, which occur in trace quantities in ice, were recovered by stir bar sorptive extraction and analyzed by gas chromatography/time-of-flight mass spectrometry coupled with thermal desorption. These methods permitted identification and quantitation of numerous biomarkers in sample volumes of as little as 10 ml. At least one wet and dry season sample was analyzed for every year. Observed biomarkers that may be derived from vegetation fires include several polycyclic aromatic hydrocarbons (PAHs), atraric acid, 2-ethylhexyl p-methoxycinnamate, and a range of other aromatic compounds. Abrupt changes in compound abundances were superimposed on decadal variability. Systematic offsets between wet and dry season abundances were not observed, suggesting that the biomass burning signal is not biased by seasonal depositional effects, such as dust delivery. Inputs likely reflect a combination of sources from anthropogenic burning of the Amazon rainforest as well as natural fires related to aridity, and include both high and low elevation vegetation. These compounds and techniques can be applied to older ice in this and other core locations as an independent estimate of aridity.

Stability of hepatitis C virus RNA and anti-HCV antibody in air-dried and freeze-dried human plasma samples.

PubMed

Poe, Amanda; Duong, Ngocvien Thi; Bedi, Kanwar; Kodani, Maja

2018-03-01

Diagnosis of hepatitis C virus (HCV) infection is based on testing for antibodies to HCV (anti-HCV), hepatitis C core antigen (HCV cAg) and HCV RNA. To ensure quality control (QC) and quality assurance (QA), proficiency panels are provided by reference laboratories and various international organizations, requiring costly dry ice shipments to maintain specimen integrity. Alternative methods of specimen preservation and transport can save on shipping and handling and help in improving diagnostics by facilitating QA/QC of various laboratories especially in resource limited countries. Plasma samples positive for anti-HCV and HCV RNA were either dried using dried tube specimens (DTS) method or lyophilization for varying durations of time and temperature. Preservation of samples using DTS method resulted in loss of anti-HCV reactivity for low-positive samples and did not generate enough volume for HCV RNA testing. Lyophilized samples tested positive for anti-HCV even after storage at 4 °C and 25 °C for 12 weeks. Further, HCV RNA was detectable in 5 of 5 (100%) samples over the course of 12 week storage at 4, 25, 37 and 45 °C. In conclusion, lyophilization of specimens maintains integrity of plasma samples for testing for markers of HCV infection and can be a potent mode of sharing proficiency samples without incurring huge shipping costs and avoids challenges with dry ice shipments between donor and recipient laboratories. Copyright © 2017. Published by Elsevier B.V.

A TEM analysis of nanoparticulates in a Polar ice core

DOE Office of Scientific and Technical Information (OSTI.GOV)

Esquivel, E.V.; Murr, L.E

2004-03-15

This paper explores the prospect for analyzing nanoparticulates in age-dated ice cores representing times in antiquity to establish a historical reference for atmospheric particulate regimes. Analytical transmission electron microscope (TEM) techniques were utilized to observe representative ice-melt water drops dried down on carbon/formvar or similar coated grids. A 10,000-year-old Greenland ice core was melted, and representative water drops were transferred to coated grids in a clean room environment. Essentially, all particulates observed were aggregates and either crystalline or complex mixtures of nanocrystals. Especially notable was the observation of carbon nanotubes and related fullerene-like nanocrystal forms. These observations are similar withmore » some aspects of contemporary airborne particulates including carbon nanotubes and complex nanocrystal aggregates.« less

Broadband Acoustic Resonance Dissolution Spectroscopy (BARDS): A rapid test for enteric coating thickness and integrity of controlled release pellet formulations.

PubMed

Alfarsi, Anas; Dillon, Amy; McSweeney, Seán; Krüse, Jacob; Griffin, Brendan; Devine, Ken; Sherry, Patricia; Henken, Stephan; Fitzpatrick, Stephen; Fitzpatrick, Dara

2018-06-10

There are no rapid dissolution based tests for determining coating thickness, integrity and drug concentration in controlled release pellets either during production or post-production. The manufacture of pellets requires several coating steps depending on the formulation. The sub-coating and enteric coating steps typically take up to six hours each followed by additional drying steps. Post production regulatory dissolution testing also takes up to six hours to determine if the batch can be released for commercial sale. The thickness of the enteric coating is a key factor that determines the release rate of the drug in the gastro-intestinal tract. Also, the amount of drug per unit mass decreases with increasing thickness of the enteric coating. In this study, the coating process is tracked from start to finish on an hourly basis by taking samples of pellets during production and testing those using BARDS (Broadband Acoustic Resonance Dissolution Spectroscopy). BARDS offers a rapid approach to characterising enteric coatings with measurements based on reproducible changes in the compressibility of a solvent due to the evolution of air during dissolution. This is monitored acoustically via associated changes in the frequency of induced acoustic resonances. A steady state acoustic lag time is associated with the disintegration of the enteric coatings in basic solution. This lag time is pH dependent and is indicative of the rate at which the coating layer dissolves. BARDS represents a possible future surrogate test for conventional USP dissolution testing as its data correlates directly with the thickness of the enteric coating, its integrity and also with the drug loading as validated by HPLC. Copyright © 2018 Elsevier B.V. All rights reserved.

Mars Polar Lander Landing Site Noon-time Temperatures

NASA Technical Reports Server (NTRS)

1999-01-01

The Mars Polar Lander will arrive at Mars on December 3, 1999. TES analysis of data from the pre-mapping phase demonstrate the spacecraft is expected to land on bare ground, free of -128oC (-200oF) dry ice that completely covered this region during the winter. This image shows the noon-time temperatures of data within the landing site in January, 1998, almost exactly one Martian year prior to MPL landing. The plus sign marks the landing site. The thick white line shows the location of the polar layered deposits. Temperatures are given in Kelvin. The temperature of CO₂ frost (dry ice) on Mars is 145K (-128oC), approximately -200oF. Temperatures above 200K show the absence of CO₂ frost.

Catalytic conversion of hydrocarbons to hydrogen and high-value carbon

DOEpatents

Shah, Naresh; Panjala, Devadas; Huffman, Gerald P.

2005-04-05

The present invention provides novel catalysts for accomplishing catalytic decomposition of undiluted light hydrocarbons to a hydrogen product, and methods for preparing such catalysts. In one aspect, a method is provided for preparing a catalyst by admixing an aqueous solution of an iron salt, at least one additional catalyst metal salt, and a suitable oxide substrate support, and precipitating metal oxyhydroxides onto the substrate support. An incipient wetness method, comprising addition of aqueous solutions of metal salts to a dry oxide substrate support, extruding the resulting paste to pellet form, and calcining the pellets in air is also discloses. In yet another aspect, a process is provided for producing hydrogen from an undiluted light hydrocarbon reactant, comprising contacting the hydrocarbon reactant with a catalyst as described above in a reactor, and recovering a substantially carbon monoxide-free hydrogen product stream. In still yet another aspect, a process is provided for catalytic decomposition of an undiluted light hydrocarbon reactant to obtain hydrogen and a valuable multi-walled carbon nanotube coproduct.

Influence of calcium on fungal growth, hyphal morphology and citric acid production in Aspergillus niger.

PubMed

Pera, L M; Callieri, D A

1997-01-01

Addition of 0.5 g/L CaCl2 to the fermentation medium lowered the final biomass dry mass by 35% and increased the uptake of phosphate and sucrose, and the production of citric acid by 15, 35 and 50%, respectively. In a medium deprived of Ca2+ the microorganism displayed both a pelleted and a filamentous form of growth, the hyphae being scarcely branched, without bulbous cells. An addition of Ca2+ induced a pelleted form of growth, highly branched hyphae and numerous bulbous cells. Bulbous cells growing in the presence of Ca2+ exhibited cell walls composed of laminated layers, and featured vesicles associated with the wall and/or the cell membrane, containing numerous inclusions. The cytotoxic effect of high concentrations of citric acid in the medium as well as an increase of the activity of N-acetyl-beta-D-glucosaminidase, a lytic enzyme, might be involved in these morphological changes.

Effect of temperature in the selective reduction process of limonite nickel ore

NASA Astrophysics Data System (ADS)

Mayangsari, W.; Febriana, Eni; Prasetyo, A. B.

2018-05-01

Temperature is the main factor for the reduction process that influence to reduction degree, phase and morphology transformation. In order to determine these effects which is caused by reduction temperature, this study was conducted. Limoniticnickel ore was prepared by drying and size reduction. A part of prepared limonitewas characterized with XRF to determine the chemical composition. The other part was mixed with reducing agent and CaSO4 to produce pellet. A series of selective reduction processes were conducted to the pellet by using graphite crucible in the muffle furnace carbolite at 800° - 1100°C for 60 minutes. Reduced ore characterized by using XRD and SEM analysis. Based on the result study, weight loss and reduction degree increase as temperature raised along with CaSO4 addition. Moreover, it caused decomposition and transformation to the metallic phase of kamacite and iron up to 7.51% and 41.44% respectively in the reduction process at 1100°C for 60 minutes. Furthermore, particle size growth as metallic phase content increased.

HiRISE observations of new impact craters exposing Martian ground ice

USGS Publications Warehouse

Dundas, Colin M.; Byrne, Shane; McEwen, Alfred S.; Mellon, Michael T.; Kennedy, Megan R.; Daubar, Ingrid J.; Saper, Lee

2014-01-01

Twenty small new impact craters or clusters have been observed to excavate bright material inferred to be ice at mid and high latitudes on Mars. In the northern hemisphere, the craters are widely distributed geographically and occur at latitudes as low as 39°N. Stability modeling suggests that this ice distribution requires a long-term average atmospheric water vapor content around 25 precipitable microns, more than double the present value, which is consistent with the expected effect of recent orbital variations. Alternatively, near-surface humidity could be higher than expected for current column abundances if water vapor is not well-mixed with atmospheric CO2, or the vapor pressure at the ice table could be lower due to salts. Ice in and around the craters remains visibly bright for months to years, indicating that it is clean ice rather than ice-cemented regolith. Although some clean ice may be produced by the impact process, it is likely that the original ground ice was excess ice (exceeding dry soil pore space) in many cases. Observations of the craters suggest small-scale heterogeneities in this excess ice. The origin of such ice is uncertain. Ice lens formation by migration of thin films of liquid is most consistent with local heterogeneity in ice content and common surface boulders, but in some cases nearby thermokarst landforms suggest large amounts of excess ice that may be best explained by a degraded ice sheet.

A design protocol for tailoring ice-templated scaffold structure

PubMed Central

Pawelec, K. M.; Husmann, A.; Best, S. M.; Cameron, R. E.

2014-01-01

In this paper, we show, for the first time, the key link between scaffold architecture and latent heat evolution during the production of porous biomedical collagen structures using freeze-drying. Collagen scaffolds are used widely in the biomedical industry for the repair and reconstruction of skeletal tissues and organs. Freeze-drying of collagen slurries is a standard industrial process, and, until now, the literature has sought to characterize the influence of set processing parameters including the freezing protocol and weight percentage of collagen. However, we are able to demonstrate, by monitoring the local thermal events within the slurry during solidification, that nucleation, growth and annealing processes can be controlled, and therefore we are able to control the resulting scaffold architecture. Based on our correlation of thermal profile measurements with scaffold architecture, we hypothesize that there is a link between the fundamental freezing of ice and the structure of scaffolds, which suggests that this concept is applicable not only for collagen but also for ceramics and pharmaceuticals. We present a design protocol of strategies for tailoring the ice-templated scaffold structure. PMID:24402916

A Mass Diffusion Model for Dry Snow Utilizing a Fabric Tensor to Characterize Anisotropy

NASA Astrophysics Data System (ADS)

Shertzer, Richard H.; Adams, Edward E.

2018-03-01

A homogenization algorithm for randomly distributed microstructures is applied to develop a mass diffusion model for dry snow. Homogenization is a multiscale approach linking constituent behavior at the microscopic level—among ice and air—to the macroscopic material—snow. Principles of continuum mechanics at the microscopic scale describe water vapor diffusion across an ice grain's surface to the air-filled pore space. Volume averaging and a localization assumption scale up and down, respectively, between microscopic and macroscopic scales. The model yields a mass diffusivity expression at the macroscopic scale that is, in general, a second-order tensor parameterized by both bulk and microstructural variables. The model predicts a mass diffusivity of water vapor through snow that is less than that through air. Mass diffusivity is expected to decrease linearly with ice volume fraction. Potential anisotropy in snow's mass diffusivity is captured due to the tensor representation. The tensor is built from directional data assigned to specific, idealized microstructural features. Such anisotropy has been observed in the field and laboratories in snow morphologies of interest such as weak layers of depth hoar and near-surface facets.

Stratospheric and solar cycle effects on long-term variability of mesospheric ice clouds

NASA Astrophysics Data System (ADS)

Lübken, F.-J.; Berger, U.; Baumgarten, G.

2009-11-01

Model results of mesospheric ice layers and background conditions at 69°N from 1961 to 2008 are analyzed. The model nudges to European Centre for Medium-Range Weather Forecasts data below ˜45 km. Greenhouse gas concentrations in the mesosphere are kept constant. At polar mesospheric cloud (PMC) altitudes (83 km) temperatures decrease until the mid 1990s by -0.08 K/yr resulting in trends of PMC brightness, occurrence rates, and, to a lesser extent, in PMC altitudes (-0.0166 km/yr). Ice layer trends are consistent with observations by ground-based and satellite instruments. Water vapor increases at PMC heights and decreases above due to increased freeze-drying caused by the temperature trend. Temperature trends in the mesosphere mainly come from shrinking of the stratosphere and from dynamical effects. A solar cycle modulation of H2O is observed in the model consistent with satellite observations. The effect on ice layers is reduced because of redistribution of H2O by freeze-drying. The accidental coincidence of low temperatures and solar cycle minimum in the mid 1990s leads to an overestimation of solar effects on ice layers. A strong correlation between temperatures and PMC altitudes is observed. Applied to historical measurements this gives negligible temperature trends at PMC altitudes (˜0.01-0.02 K/yr). Strong correlations between PMC parameters and background conditions deduced from the model confirm the standard scenario of PMC formation. The PMC sensitivity on temperatures, water vapor, and Ly-α is investigated. PMC heights show little variation with background parameters whereas brightness and occurrence rates show large variations. None of the background parameters can be ignored regarding its influence on ice layers.

Stratospheric and solar cycle effects on long-term variability of mesospheric ice clouds

NASA Astrophysics Data System (ADS)

Lübken, F.-J.; Berger, U.; Baumgarten, G.

2009-01-01

Model results of mesospheric ice layers and background conditions at 69°N from 1961 to 2008 are analyzed. The model nudges to European Centre for Medium-Range Weather Forecasts data below ˜45 km. Greenhouse gas concentrations in the mesosphere are kept constant. At polar mesospheric cloud (PMC) altitudes (83 km) temperatures decrease until the mid 1990s by -0.08 K/yr resulting in trends of PMC brightness, occurrence rates, and, to a lesser extent, in PMC altitudes (-0.0166 km/yr). Ice layer trends are consistent with observations by ground-based and satellite instruments. Water vapor increases at PMC heights and decreases above due to increased freeze-drying caused by the temperature trend. Temperature trends in the mesosphere mainly come from shrinking of the stratosphere and from dynamical effects. A solar cycle modulation of H2O is observed in the model consistent with satellite observations. The effect on ice layers is reduced because of redistribution of H2O by freeze-drying. The accidental coincidence of low temperatures and solar cycle minimum in the mid 1990s leads to an overestimation of solar effects on ice layers. A strong correlation between temperatures and PMC altitudes is observed. Applied to historical measurements this gives negligible temperature trends at PMC altitudes (˜0.01-0.02 K/yr). Strong correlations between PMC parameters and background conditions deduced from the model confirm the standard scenario of PMC formation. The PMC sensitivity on temperatures, water vapor, and Ly-α is investigated. PMC heights show little variation with background parameters whereas brightness and occurrence rates show large variations. None of the background parameters can be ignored regarding its influence on ice layers.

Cryoseism Vibrational Movement and Sorting of Detritus of Mars' Regolith Bedforms (E.G., ~ Streaks, Gullies): a New, Dry, Midsummer Antarctic Analogue Mechanism

NASA Astrophysics Data System (ADS)

Ford, A. B.

2015-12-01

"SNAP!, CRACK!, POP!" The sounds reverberated across newly shaded permafrost of unusual talus aprons (Ford & Andersen, 1967; J. Geol., 75, 722-732) of interior Antarctica (lats. >84°S; Thiel, Pensacola mtns.), coming from ice cracking under tensile failure (cryoseisms). Apron regoliths show conspicuously reversed downslope particle-size sorting and downslope-oriented lineations (debris-cleared tracts; stone stripes) formed by vibrational movement of detritus by midsummer, diurnal cracking of ice. Moving laterally by vibrations away from cracks, with downslope component by gravity, finer detritus becomes concentrated downslope from coarser debris of initial cliff fall — winnowed, as if on a gigantic vibrating shaking table. Slopes outside shade zones remain free of cracking. Diurnal midday shading of solar-warmed, debris-mantled permafrost- and glacier-surface ice at low ambient midsummer temperatures produces high strain-loading rates that exceed tensile toughness of inhomogeneous, polycrystalline ice containing zones of older but sealed cracks. This dry, mechanical, cryoseism mechanism is here proposed also for now waterless Mars and other icy Solar System bodies. Regolith features of Mars' cryosphere may appear different from anrarctic analogues owing to likely operation over tens if not hundreds of millions of years longer than on Earth. The strain distributions in tensile failure of ice better explain a common spacing uniformity of many martian linear features than others' proposed origins, and for some "active" streaks and gully channels, TARS, RSL and dune-slipface channels, as well as for dune orthogonality, diurnal moonquakes and asteroid-regolith detrital sorting (e.g., "rubble-pile" 25143-Itokawa). Because periodic shade from topography (canyons, craters, etc.) is needed, the mechanism is not expected on flattish terrains where more normal annual cooling rates produce the common polygonal tensile fracturing of ice

Mineralogy of Antarctica Dry Valley Soils: Implications for Pedogenic Processes on Mars

NASA Technical Reports Server (NTRS)

Quinn, J. E.; Ming, D. W.; Morris, R. V.; Douglas, S.; Kounaves, S. P.; McKay, C. P.; Tamppari, L, K.; Smith, P. H.; Zent, A. P.; Archer, P. D., Jr.

2010-01-01

The Antarctic Dry Valleys (ADVs) located in the Transantarctic Mountains are the coldest and driest locations on Earth. The mean annual air temperature is -20 C or less and the ADVs receive 100mm or less of precipitation annually in the form of snow. The cold and dry climate in the ADVs is one of the best terrestrial analogs for the climatic conditions on Mars [2]. The soils in the ADVs have been categorized into three soil moisture zones: subxerous, xerous and ultraxerous. The subxerous zone is a coastal region in which soils have ice-cemented permafrost relatively close to the surface. Moisture is available in relatively large amounts and soil temperatures are above freezing throughout the soil profile (above ice permafrost) in summer months. The xerous zone, the most widespread of the three zones, is an inland region with a climate midway between the subxerous and ultraxerous. The soils from this zone have dry permafrost at moderate depths (30-75cm) but have sufficient water in the upper soil horizons to allow leaching of soluble materials. The ultraxerous zone is a high elevation zone, where both temperature and precipitation amounts are very low resulting in dry permafrost throughout the soil profile. The three moisture regime regions are similar to the three microclimatic zones (coastal thaw, inland mixed, stable upland) defined by Marchant and Head.

Validation of cold chain shipping environment for transport of allografts as part of a human tissue bank returns policy.

PubMed

Rooney, P; Eagle, M J; Kearney, J N

2015-12-01

Human tissue is shipped to surgeons in the UK in either a freeze-dried or frozen state. To ensure quality and safety of the tissue, frozen tissue must be shipped in insulated containers such that tissue is maintained at an appropriate temperature. UK Blood Transfusion Service regulations state "Transportation systems must be validated to show maintenance of the required storage temperature" and also state that frozen, non-cryopreserved tissue "must be transported… at -20 °C or lower" (Guidelines for the Blood Transfusion Services in the United Kingdom, 8th Edn. 2013). To maintain an expiry date for frozen tissue longer than 6 months, the tissue must be maintained at a temperature of -40 °C or below. The objective of this study was to evaluate and validate the capability of a commercially available insulated polystyrene carton (XPL10), packed with dry ice, to maintain tissue temperature below -40 °C. Tissue temperature of a single frozen femoral head or a single frozen Achilles tendon, was recorded over a 4-day period at 37 °C, inside a XPL10 carton with dry ice as refrigerant. The data demonstrate that at 37 °C, the XPL10 carton with 9.5 kg of dry ice maintained femoral head and tendon tissue temperature below -55 °C for at least 48 h; tissue temperature did not rise above -40 °C until at least 70 h. Data also indicated that at a storage temperature lower than 37 °C, tissue temperature was maintained for longer periods.

Geomorphological evidence for ground ice on dwarf planet Ceres

USGS Publications Warehouse

Schmidt, Britney E.; Hughson, Kynan H.G.; Chilton, Heather T.; Scully, Jennifer E. C.; Platz, Thomas; Nathues, Andreas; Sizemore, Hanna; Bland, Michael T.; Byrne, Shane; Marchi, Simone; O'Brien, David; Schorghofer, Norbert; Hiesinger, Harald; Jaumann, Ralf; Hendrick Pasckert, Jan; Lawrence, Justin D.; Buzckowski, Debra; Castillo-Rogez, Julie C.; Sykes, Mark V.; Schenk, Paul M.; DeSanctis, Maria-Cristina; Mitri, Giuseppe; Formisano, Michelangelo; Li, Jian-Yang; Reddy, Vishnu; Le Corre, Lucille; Russell, Christopher T.; Raymond, Carol A.

2017-01-01

Five decades of observations of Ceres suggest that the dwarf planet has a composition similar to carbonaceous meteorites and may have an ice-rich outer shell protected by a silicate layer. NASA’s Dawn spacecraft has detected ubiquitous clays, carbonates and other products of aqueous alteration across the surface of Ceres, but surprisingly it has directly observed water ice in only a few areas. Here we use Dawn Framing Camera observations to analyse lobate morphologies on Ceres’ surface and we infer the presence of ice in the upper few kilometres of Ceres. We identify three distinct lobate morphologies that we interpret as surface flows: thick tongue-shaped, furrowed flows on steep slopes; thin, spatulate flows on shallow slopes; and cuspate sheeted flows that appear fluidized. The shapes and aspect ratios of these flows are different from those of dry landslides—including those on ice-poor Vesta—but are morphologically similar to ice-rich flows on other bodies, indicating the involvement of ice. Based on the geomorphology and poleward increase in prevalence of these flows, we suggest that the shallow subsurface of Ceres is comprised of mixtures of silicates and ice, and that ice is most abundant near the poles.

Performance of an airborne imaging 92/183 GHz radiometer during the Bering Sea Marginal Ice Zone Experiment (MIZEX-WEST)

NASA Technical Reports Server (NTRS)

Gagliano, J. A.; Mcsheehy, J. J.; Cavalieri, D. J.

1983-01-01

An airborne imaging 92/183 GHz radiometer was recently flown onboard NASA's Convair 990 research aircraft during the February 1983 Bering Sea Marginal Ice Zone Experiment (MIZEX-WEST). The 92 GHz portion of the radiometer was used to gather ice signature data and to generate real-time millimeter wave images of the marginal ice zone. Dry atmospheric conditions in the Arctic resulted in good surface ice signature data for the 183 GHz double sideband (DSB) channel situated + or - 8.75 GHz away from the water vapor absorption line. The radiometer's beam scanner imaged the marginal ice zone over a + or - 45 degrees swath angle about the aircraft nadir position. The aircraft altitude was 30,000 feet (9.20 km) maximum and 3,000 feet (0.92 km) minimum during the various data runs. Calculations of the minimum detectable target (ice) size for the radiometer as a function of aircraft altitude were performed. In addition, the change in the atmospheric attenuation at 92 GHz under varying weather conditions was incorporated into the target size calculations. A radiometric image of surface ice at 92 GHz in the marginal ice zone is included.

Implementation of a process analytical technology system in a freeze-drying process using Raman spectroscopy for in-line process monitoring.

PubMed

De Beer, T R M; Allesø, M; Goethals, F; Coppens, A; Heyden, Y Vander; De Diego, H Lopez; Rantanen, J; Verpoort, F; Vervaet, C; Remon, J P; Baeyens, W R G

2007-11-01

The aim of the present study was to propose a strategy for the implementation of a Process Analytical Technology system in freeze-drying processes. Mannitol solutions, some of them supplied with NaCl, were used as models to freeze-dry. Noninvasive and in-line Raman measurements were continuously performed during lyophilization of the solutions to monitor real time the mannitol solid state, the end points of the different process steps (freezing, primary drying, secondary drying), and physical phenomena occurring during the process. At-line near-infrared (NIR) and X-ray powder diffractometry (XRPD) measurements were done to confirm the Raman conclusions and to find out additional information. The collected spectra during the processes were analyzed using principal component analysis and multivariate curve resolution. A two-level full factorial design was used to study the significant influence of process (freezing rate) and formulation variables (concentration of mannitol, concentration of NaCl, volume of freeze-dried sample) upon freeze-drying. Raman spectroscopy was able to monitor (i) the mannitol solid state (amorphous, alpha, beta, delta, and hemihydrate), (ii) several process step end points (end of mannitol crystallization during freezing, primary drying), and (iii) physical phenomena occurring during freeze-drying (onset of ice nucleation, onset of mannitol crystallization during the freezing step, onset of ice sublimation). NIR proved to be a more sensitive tool to monitor sublimation than Raman spectroscopy, while XRPD helped to unravel the mannitol hemihydrate in the samples. The experimental design results showed that several process and formulation variables significantly influence different aspects of lyophilization and that both are interrelated. Raman spectroscopy (in-line) and NIR spectroscopy and XRPD (at-line) not only allowed the real-time monitoring of mannitol freeze-drying processes but also helped (in combination with experimental design) us to understand the process.

Analysing biomass torrefaction supply chain costs.

PubMed

Svanberg, Martin; Olofsson, Ingemar; Flodén, Jonas; Nordin, Anders

2013-08-01

The objective of the present work was to develop a techno-economic system model to evaluate how logistics and production parameters affect the torrefaction supply chain costs under Swedish conditions. The model consists of four sub-models: (1) supply system, (2) a complete energy and mass balance of drying, torrefaction and densification, (3) investment and operating costs of a green field, stand-alone torrefaction pellet plant, and (4) distribution system to the gate of an end user. The results show that the torrefaction supply chain reaps significant economies of scale up to a plant size of about 150-200 kiloton dry substance per year (ktonDS/year), for which the total supply chain costs accounts to 31.8 euro per megawatt hour based on lower heating value (€/MWhLHV). Important parameters affecting total cost are amount of available biomass, biomass premium, logistics equipment, biomass moisture content, drying technology, torrefaction mass yield and torrefaction plant capital expenditures (CAPEX). Copyright © 2013 Elsevier Ltd. All rights reserved.

Antiinflammatory effect of Forsythia suspensa Vahl and its active fraction.

PubMed

Ozaki, Y; Rui, J; Tang, Y; Satake, M

1997-08-01

This study was carried out to elucidate the antiinflammatory effect of 70% methanol extract obtained from the dried fruit of Forsythia suspensa Vahl and its active principles. F. suspensa was extracted with 70% methanol and freeze-dried to give a powdered extract. The methanol extract was then dissolved in water and extracted with n-hexane, and the n-hexane fraction was evaporated to dryness under vacuum; the water fraction was freeze-dried to give a powdered extract. The antiinflammatory activity of the extract and fractions was investigated on acetic acid-induced vascular permeability and writhing symptoms in mice, as well as on carrageenin-induced edema and cotton pellet-induced granuloma formation in rats. The methanol extract and the n-hexane fraction (p.o.) showed the antiinflammatory effect and analgesic effect, but the water fraction did not. These results suggested that the antiinflammatory and analgesic activity induced by the methanol extract shifted to the n-hexane fraction and the active principles may be lipophilic compounds.

Biomass logistics analysis for large scale biofuel production: case study of loblolly pine and switchgrass.

PubMed

Lu, Xiaoming; Withers, Mitch R; Seifkar, Navid; Field, Randall P; Barrett, Steven R H; Herzog, Howard J

2015-05-01

The objective of this study was to assess the costs, energy consumption and greenhouse gas (GHG) emissions throughout the biomass supply chain for large scale biofuel production. Two types of energy crop were considered, switchgrass and loblolly pine, as representative of herbaceous and woody biomass. A biomass logistics model has been developed to estimate the feedstock supply system from biomass production through transportation. Biomass in the form of woodchip, bale and pellet was investigated with road, railway and waterway transportation options. Our analysis indicated that the farm or forest gate cost is lowest for loblolly pine whole tree woodchip at $39.7/dry tonne and highest for switchgrass round bale at $72.3/dry tonne. Switchgrass farm gate GHG emissions is approximately 146kgCO2e/dry tonne, about 4 times higher than loblolly pine. The optimum biomass transportation mode and delivered form are determined by the tradeoff between fixed and variable costs for feedstock shipment. Copyright © 2015 Elsevier Ltd. All rights reserved.

Emission of PCDD/F, PCB, and HCB from combustion of firewood and pellets in residential stoves and boilers.

PubMed

Hedman, Björn; Naslund, Morgan; Marklund, Stellan

2006-08-15

To assess potential emissions of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs), and hexachlorobenzene (HCB) from residential combustion of biofuels, experiments were performed in which various types of pellets and firewood were combusted in four types of stoves and boilers, with both full and reduced rates of air supply. Intermittent combustion of wood pellets resulted in emissions of 11 ng-(WHO-TEQ)/kg combusted fuel (dry weight). A modern, environmentally certified boiler yielded somewhat lower emissions of PCCD/F and PCB than a wood stove. Both gave <0.1 ng(WHO-TEQ)/m3n (1.3-6.5 ng(WHO-TEQ)/kg) and considerably lower emissions than an old boiler (7.0-13 ng(WHO-TEQ)/kg). No positive effect on emissions could be observed in full air combustion (simulating the use of a heat storage tank) compared to combustion with reduced air. Two of the wood combustion experiments included paper and plastic waste fuels. Chlorine-containing plastic waste gave rise to high emissions: ca. 310 ng(WHO-TEQ)/ kg over the whole combustion cycle. The homologue profiles of PCDD/Fs show characteristic differences between ashes and flue gas from combustions with different levels of air supply. These differences do not, however, seem to have any correlation to the relative amount of toxic congeners.

A prelanding assessment of the ice table depth and ground ice characteristics in Martian permafrost at the Phoenix landing site

USGS Publications Warehouse

Mellon, M.T.; Boynton, W.V.; Feldman, W.C.; Arvidson, R. E.; Titus, Joshua T.N.; Bandfield, L.; Putzig, N.E.; Sizemore, H.G.

2009-01-01

We review multiple estimates of the ice table depth at potential Phoenix landing sites and consider the possible state and distribution of subsurface ice. A two-layer model of ice-rich material overlain by ice-free material is consistent with both the observational and theoretical lines of evidence. Results indicate ground ice to be shallow and ubiquitous, 2-6 cm below the surface. Undulations in the ice table depth are expected because of the thermodynamic effects of rocks, slopes, and soil variations on the scale of the Phoenix Lander and within the digging area, which can be advantageous for analysis of both dry surficial soils and buried ice-rich materials. The ground ice at the ice table to be sampled by the Phoenix Lander is expected to be geologically young because of recent climate oscillations. However, estimates of the ratio of soil to ice in the ice-rich subsurface layer suggest that that the ice content exceeds the available pore space, which is difficult to reconcile with existing ground ice stability and dynamics models. These high concentrations of ice may be the result of either the burial of surface snow during times of higher obliquity, initially high-porosity soils, or the migration of water along thin films. Measurement of the D/H ratio within the ice at the ice table and of the soil-to-ice ratio, as well as imaging ice-soil textures, will help determine if the ice is indeed young and if the models of the effects of climate change on the ground ice are reasonable. Copyright 2008 by the American Geophysical Union.

Mesoporous materials for antihydrogen production.

PubMed

Consolati, Giovanni; Ferragut, Rafael; Galarneau, Anne; Di Renzo, Francesco; Quasso, Fiorenza

2013-05-07

Antimatter is barely known by the chemist community and this article has the vocation to explain how antimatter, in particular antihydrogen, can be obtained, as well as to show how mesoporous materials could be used as a further improvement for the production of antimatter at very low temperatures (below 1 K). The first experiments with mesoporous materials highlighted in this review show very promising and exciting results. Mesoporous materials such as mesoporous silicon, mesoporous material films, pellets of MCM-41 and silica aerogel show remarkable features for antihydrogen formation. Yet, the characteristics for the best future mesoporous materials (e.g. pore sizes, pore connectivity, shape, surface chemistry) remain to be clearly identified. For now among the best candidates are pellets of MCM-41 and aerogel with pore sizes between 10 and 30 nm, possessing hydrophobic patches on their surface to avoid ice formation at low temperature. From a fundamental standpoint, antimatter experiments could help to shed light on open issues, such as the apparent asymmetry between matter and antimatter in our universe and the gravitational behaviour of antimatter. To this purpose, basic studies on antimatter are necessary and a convenient production of antimatter is required. It is exactly where mesoporous materials could be very useful.

Evidence From Hydrogen Isotopes in Meteorites for a Martian Permafrost

NASA Technical Reports Server (NTRS)

Usui, T.; Alexander, C. M. O'D.; Wang, J.; Simon, J. I.; Jones, J. H.

2014-01-01

Fluvial landforms on Mars suggest that it was once warm enough to maintain persistent liquid water on its surface. The transition to the present cold and dry Mars is closely linked to the history of surface water, yet the evolution of surficial water is poorly constrained. We have investigated the evolution of surface water/ ice and its interaction with the atmosphere by measurements of hydrogen isotope ratios (D/H: deuterium/ hydrogen) of martian meteorites. Hydrogen is a major component of water (H2O) and its isotopes fractionate significantly during hydrological cycling between the atmosphere, surface waters, ground ice, and polar cap ice. Based on in situ ion microprobe analyses of three geochemically different shergottites, we reported that there is a water/ice reservoir with an intermediate D/H ratio (delta D = 1,000?2500 %) on Mars. Here we present the possibility that this water/ice reservoir represents a ground-ice/permafrost that has existed relatively intact over geologic time.

Wave-ice interaction, observed and modelled

NASA Astrophysics Data System (ADS)

Gemmrich, Johannes

2017-04-01

The need for wide-spread, up-to-date sea state predictions and observations in the emerging ice-free Arctic will further increase as the region will open up to marine operations. Wave models for arctic regions have to capture the additional wave physics associated with wave-ice interactions, and different prediction schemes have to be tested against observations. Here we present examples of spatial wave field parameters obtained from TerraSAR-X StripMap swaths in the southern Beaufort Sea taken as part of the "Arctic Sea State and Boundary Layer DRI". Fetch evolution of the significant wave height and length in open waters, and dominant wave lengths and the high frequency cut-off of the wave spectrum in ice are readily extracted from the SAR (synthetic aperture radar) data. A surprising result is that wave evolution in off-ice wind conditions is more rapidly than the fetch evolution in off-land cases, suggesting seeding of the wave field within the ice-covered region.

A Novel Concrete-Based Sensor for Detection of Ice and Water on Roads and Bridges

PubMed Central

Aljuboori, Mohammed

2017-01-01

Hundreds of people are killed or injured annually in the United States in accidents related to ice formation on roadways and bridge decks. In this paper, a novel embedded sensor system is proposed for the detection of black ice as well as wet, dry, and frozen pavement conditions on roads, runways, and bridges. The proposed sensor works by detecting changes in electrical resistance between two sets of stainless steel poles embedded in the concrete sensor to assess surface and near-surface conditions. A preliminary decision algorithm is developed that utilizes sensor outputs indicating resistance changes and surface temperature. The sensor consists of a 102-mm-diameter, 38-mm-high, concrete cylinder. Laboratory results indicate that the proposed sensor can effectively detect surface ice and wet conditions even in the presence of deicing chlorides and rubber residue. This sensor can further distinguish black ice from ice that may exist within concrete pores. PMID:29240710

Applications of Shock Wave Research to Developments of Therapeutic Devices.

NASA Astrophysics Data System (ADS)

Takayama, Kazuyoshi

2007-06-01

Underwater shock wave research applied to medicine started in 1980 by exploding micro lead azide pellets in water. Collaboration with urologists in the School of Medicine, Tohoku University at the same time was directed to disintegration of kidney stones by controlling shock waves. We initially proposed a miniature truncated ellipsoidal cavity for generating high-pressures enough to disintegrate the stone but gave up the idea, when encountering the Dornie Systems' invention of an extracorporeal shock wave lithotripter (ESWL). Then we confirmed its effectiveness by using 10 mg silver azide pellets and constructed our own lithotripter, which was officially approved for a clinical use in 1987. Tissue damage during ESWL was attributable to bubble collapse and we convinced it could be done in a controlled fashion. In 1996, we used 160 mJ pulsed Ho:YAG laser beam focusing inside a catheter for shock generation and applied it to the revascularization of cerebral embolism, which is recently expanded to the treatment of pulmonary infarction. Micro water jets discharged in air were so effective to dissect soft tissues preserving small blood vessels. Animal experiments are successfully performed with high frequency water jets driven by an actuator-assisted micro-pump. A metal foil is deformed at high speed by a Q-switched Nd:YAG laser beam loading. We used this technique to project micro-particles or dry drugs attached on its reverse side and extended it to a laser ablation assisted dry drug delivery or DNA introductory system.

Microwave signatures of snow and fresh water ice

NASA Technical Reports Server (NTRS)

Schmugge, T.; Wilheit, T. T.; Gloersen, P.; Meier, M. F.; Frank, D.; Dirmhirn, I.

1973-01-01

During March of 1971, the NASA Convair 990 Airborne Observatory carrying microwave radiometers in the wavelength range 0.8 to 21 cm was flown over dry snow with different substrata: Lake ice at Bear Lake in Utah; wet soil in the Yampa River Valley near Steamboat Springs, Colorado; and glacier ice, firm and wet snow on the South Cascade Glacier in Washington. The data presented indicate that the transparency of the snow cover is a function of wavelength. False-color images of microwave brightness temperatures obtained from a scanning radiometer operating at a wavelength of 1.55 cm demonstrate the capability of scanning radiometers for mapping snowfields.

Cd, Ni, Cr and Pb distribution in biosolid pellets used as soil amendment

NASA Astrophysics Data System (ADS)

Jordán, Manuel M.; Rincón-Mora, Beatriz; Belén Almendro-Candel, María; Navarro Pedreño, Jose; Gómez Lucas, Ignacio; Bech, Jaume; Roca, Nuria; Pardo, Francisco

2016-04-01

The application of biosolids to a soil is a method that offers important benefits (Navarro et al. 2003). The transport and application costs are quite low (mostly if they are dehydrated biosolids or pellets) if soils are located near a wastewater treatment plant. It is possible to recycle nutrients (N, P, and K) and organic matter by improving the physical and chemical characteristics of the soil and by reducing the fertilizer costs. However, the use of biosolids may also has several problems, such as the presence of quantities of metals that could be toxic for plants or could contaminate ground-waters after being leached. Heavy metals are one of the most serious environmental pollutants because of its high toxicity, abundance and easy accumulation by plant (Soriano-Disla et al. 2014; Rosen and Chen 2014). Contamination of soils by potentially toxic elements (e.g. Cd, Ni, Cr, Pb) from amendments of biosolids is subject to rigorous controls within the European Union. The present study was designed to examine the partition of selected heavy metals in biosolid pellets, and also to relate the distribution patterns of these metals. Samples were collected from the treatment of urban wastewater at the drying grounds of a wastewater processing plant. The samples correspond to biosolids with humidities below 20% and are representative of the three horizons within the pile: the isolation surface (H1), the mesophilous area (H2), and the thermophilous area (H3). Biosolid aggregates were placed in a pellet press and then compacted. Total content of metals was determined following microwave digestion and analysed by ICP/MS. Triplicate samples were weighed in polycarbonate centrifuge tubes and sequentially extracted. The distribution of chemical forms of Cd, Ni, Cr, and Pb in the biosolids was studied using a sequential extraction procedure that fractionates the metal into soluble-exchangeable, specifically sorbed-carbonate bound, oxidizable, reducible, and residual forms. The residual, reducible, and carbonate-sorbed forms were dominant. Higher Cr and Ni content were detected in pellets made with biosolids from the H3 horizon. The highest Cd and Ni values were detected in the H2 horizon. This behaviour was similar in the case of the Cr and Ni content. However, in the case of Cd and Pb, the highest values were detected in the H2 horizon. This experiment could be useful for establishing a general rule for taking measurements of heavy metals in biosolid pellets and other types of dry wastes. References Navarro-Pedreño J, Almendro-Candel MB, Jordán-Vidal MM, Mataix-Solera J, García-Sánchez E (2003). Mobility of Cadmium, Chromium, and Nickel through the profile of a calcisol treated with sewage sludge in the southeast of Spain. Environ. Geol. 44:545-553. Rosen V, Chen Y (2014). The influence of compost addition on heavy metal distribution between operationally defined geochemical fractions and on metal accumulation in plant. J. Soils Sed. 14:713-720. Soriano-Disla J M, Navarro-Pedreño J, Gómez I, Jordán MM (2014). The transfer of heavy metals to barley plants from soils amended with sewage sludge with different heavy metals burdens. J. Soils Sed. 14:667-696.

Effects of starch content of calf starter on growth and rumen pH in Holstein calves during the weaning transition.

PubMed

Laarman, A H; Sugino, T; Oba, M

2012-08-01

The objective of this study was to evaluate the effects of substituting high fiber byproducts for dry ground corn in calf starter on growth and rumen pH during the weaning transition. Holstein bull calves were raised on an intensified nursing program using milk replacer containing 26% CP and 18% fat. Calves were fed a texturized calf starter containing either dry ground corn at 18.8% of dry matter (DM; CRN), beet pulp replacing dry ground corn at 10.2% dietary DM (BP), or triticale dried distillers grains with solubles replacing dry ground corn and high-protein feedstuffs at 18.6% of dietary DM (DDGS) in the pellet; treatment calf starters differed only in the pellet portion. Starch concentrations of CRN, BP, and DDGS were 35.3, 33.4, and 31.4%, respectively. After a calf consumed 2.50 kg of starter for 3 consecutive days, a small ruminant rumen pH data logger was inserted orally and rumen pH was measured continuously for 4d. Calves were then killed and rumen fluid was sampled to determine volatile fatty acid profile. No difference was found in overall average daily gain or growth rates of hip height, withers height, and heart girth. During the weaning transition, rate of increase in calf starter intake was greater for calves fed DDGS compared with those fed CRN (87.7 vs. 77.5 g/d), but lower for calves fed BP compared with CRN (68.1 vs. 77.5 g/d). The area under pH 5.8 (470 vs. 295 min × pH/d) or pH 5.2 (72.7 vs. 16.4 min × pH/d) was greater for calves fed DDGS than those fed CRN. Rumen pH profile was not affected by BP treatment compared with CRN, but calves fed BP tended to have greater water intake than those fed CRN (6.6 vs. 5.8 L/d). Volatile fatty acid profile was not affected by treatment with the exception of molar proportion of butyrate, which tended to be lower for calves fed BP compared with those fed CRN (15.0 vs. 16.6%). Hay intake was positively correlated to mean rumen pH for calves used in this study (r=0.48). Decreasing dietary starch concentration did not mitigate rumen acidosis in calves during weaning transition, and low rumen pH did not adversely affect growth during the weaning transition. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Observed Melt Season Seismicity of Taylor Glacier, Antarctica

NASA Astrophysics Data System (ADS)

Carmichael, J. D.; Pettit, E. C.; Creager, K. C.

2006-12-01

Sufficient evidence exists to suggest that interaction of crevasses and meltwater accelerates ice cliff disintegration of tidewater glaciers. It is not clear what role meltwater plays in calving characteristics from dry- based polar glaciers. We have obtained seismic data from a six-sensor seismic array deployed in October of 2004 near the terminus cliffs of Taylor Glacier, West Antarctica, to analyze near-cliff seismicity throughout a melt season. Discharge data from the adjacent Lawson stream suggests that dramatic increases in meltwater volume temporally correlate with changes in seismic character near ice cliffs. We calculated source-locations for ice-quake during hours of melting and re-freezing and found most large energy events to be located near the ice cliffs. The associated spectra and waveform characteristics are indicative of literature descriptions of crevassing events.

Controlling the physical form of mannitol in freeze-dried systems.

PubMed

Mehta, Mehak; Bhardwaj, Sunny P; Suryanarayanan, Raj

2013-10-01

A potential drawback with the use of mannitol as a bulking agent is its existence as mannitol hemihydrate (MHH; C₆H₁₄O₆·0.5H₂O) in the lyophile. Once formed during freeze-drying, MHH dehydration may require secondary drying under aggressive conditions which can be detrimental to the stability of thermolabile components. If MHH is retained in the lyophile, the water released by MHH dehydration during storage has the potential to cause product instability. We systematically identified the conditions under which anhydrous mannitol and MHH crystallized in frozen systems with the goal of preventing MHH formation during freeze-drying. When mannitol solutions were cooled, the temperature of solute crystallization was the determinant of the physical form of mannitol. Based on low temperature X-ray diffractometry (using both laboratory and synchrotron sources), MHH formation was observed when solute crystallization occurred at temperatures ≤ -20 °C, while anhydrous mannitol crystallized at temperatures ≤ -10 °C. The transition temperature (anhydrate - MHH) appears to be ∼-15 °C. The use of a freeze-dryer with controlled ice nucleation technology enabled anhydrous mannitol crystallization at ∼-5 °C. Thus, ice crystallization followed by annealing at temperatures ≤ -10 °C can be an effective strategy to prevent MHH formation. Copyright © 2013 Elsevier B.V. All rights reserved.

Annealing to optimize the primary drying rate, reduce freezing-induced drying rate heterogeneity, and determine T(g)' in pharmaceutical lyophilization.

PubMed

Searles, J A; Carpenter, J F; Randolph, T W

2001-07-01

In a companion paper we show that the freezing of samples in vials by shelf-ramp freezing results in significant primary drying rate heterogeneity because of a dependence of the ice crystal size on the nucleation temperature during freezing.1 The purpose of this study was to test the hypothesis that post-freezing annealing, in which the product is held at a predetermined temperature for a specified duration, can reduce freezing-induced heterogeneity in sublimation rates. In addition, we test the impact of annealing on primary drying rates. Finally, we use the kinetics of relaxations during annealing to provide a simple measurement of T(g)', the glass transition temperature of the maximally freeze-concentrated amorphous phase, under conditions and time scales most appropriate for industrial lyophilization cycles. Aqueous solutions of hydroxyethyl starch (HES), sucrose, and HES:sucrose were either frozen by placement on a shelf while the temperature was reduced ("shelf-ramp frozen") or by immersion into liquid nitrogen. Samples were then annealed for various durations over a range of temperatures and partially lyophilized to determine the primary drying rate. The morphology of fully dried liquid nitrogen-frozen samples was examined using scanning electron microscopy. Annealing reduced primary drying rate heterogeneity for shelf-ramp frozen samples, and resulted in up to 3.5-fold increases in the primary drying rate. These effects were due to increased ice crystal sizes, simplified amorphous structures, and larger and more numerous holes on the cake surface of annealed samples. Annealed HES samples dissolved slightly faster than their unannealed counterparts. Annealing below T(g)' did not result in increased drying rates. We present a simple new annealing-lyophilization method of T(g)' determination that exploits this phenomenon. It can be carried out with a balance and a freeze-dryer, and has the additional advantage that a large number of candidate formulations can be evaluated simultaneously.

49 CFR 173.199 - Category B infectious substances.

Code of Federal Regulations, 2011 CFR

2011-10-01

... materials except— (i) Refrigerants, such as dry ice or liquid nitrogen, as authorized under paragraph (d) of... must maintain their integrity at the temperature of the refrigerant used, as well as the temperatures...

Exercise-Induced Asthma

MedlinePlus

... as triggers include: Cold air Dry air Air pollution High pollen counts Chlorine in swimming pools Chemicals used with ice rink resurfacing equipment Respiratory infections or other lung disease Activities with extended periods of deep breathing, such ...

Bloodmeal Host Congregation and Landscape Structure Impact the Estimation of Female Mosquito (Diptera: Culicidae) Abundance Using Dry Ice-Baited Traps

PubMed Central

THIEMANN, TARA; NELMS, BRITTANY; REISEN, WILLIAM K.

2011-01-01

Vegetation patterns and the presence of large numbers of nesting herons and egrets significantly altered the number of host-seeking Culex tarsalis Coquillett (Diptera: Culicidae) collected at dry ice-baited traps. The numbers of females collected per trap night at traps along the ecotone of Eucalyptus stands with and without a heron colony were always greater or equal to numbers collected at traps within or under canopy. No Cx. tarsalis were collected within or under Eucaplytus canopy during the peak heron nesting season, even though these birds frequently were infected with West Nile virus and large number of engorged females could be collected at resting boxes. These data indicate a diversion of host-seeking females from traps to nesting birds reducing sampling efficiency. PMID:21661310

Calving of Talyor Glacier, Dry Valleys, Antarctica

NASA Astrophysics Data System (ADS)

Carmichael, J. D.; Pettit, E. C.; Creager, K. C.; Hallet, B.

2007-12-01

Calving of tide-water glaciers has received considerable attention, with seismic arrays in Alaska, Greenland, and Antarctica devoted to their observation. In these environments, ice cliffs are directly coupled to oceanic temperatures. The land-based polar glaciers of the McMurdo Dry Valleys in Antarctica represent a simpler environment unaffected directly by water contact where other factors can be isolated. In particular, summer calving events of Taylor Glacier are observed to consist of precursory activity including crack growth, cliff overhang, and active seismicity at least 1 hour before collapse. We propose that collapse occurs only after a stress threshold has been crossed, evident from 'pre-calving' of ice from the cliff base 1-3 days prior to the major event. We provide photographic, seismic, and temperature data to illustrate the thermal and stress landscape for land-based calving of polar glaciers.

Utilizing commercial microwave for rapid and effective immunostaining.

PubMed

Owens, Katrina; Park, Ji H; Kristian, Tibor

2013-09-30

There is an accumulating literature demonstrating the application of microwaves across a wide spectrum of histological techniques. Although exposure to microwaves for short periods resulted in substantial acceleration of all procedures this technique still is not adopted widely. In part, this may be due to concerns over solutions that will avoid induction of thermal damage to the tissue when using standard microwave. Here, we offer a cooling setup that can be used with conventional microwave ovens. We utilized dry ice for effective cooling during microwave irradiation of tissue samples. To prevent overheating, the cups with tissue during exposure to microwaves were surrounded with powdered dry ice. Since the dry ice does not touch the walls of the cups, freezing is prevented. Overheating is avoided by alternating the microwave treatment with 1-2 min time periods when the cups are cooled outside of the microwave oven. This technique was used on mouse brain sections that were immunostained with microglia-specific CD68 antiserum and astrocyte labeling GFAP antibody. Both standard and microwave-assisted immonolabeling gave comparable results visualizing cells with fine processes and low background signal. Short incubation time in the microwave requires high concentrations of antibody for tissue immunostaining. We show that by prolonging the microwaving procedure we were able to reduce the antibody concentration to the levels used in standard immunostaining protocol. In summary, our technique gives a possibility to use a conventional microwave for rapid and effective immunolabeling resulting in reduced amount of antibody required for satisfactory immunostaining. Published by Elsevier B.V.

Nanoparticle and Gelation Stabilized Functional Composites of an Ionic Salt in a Hydrophobic Polymer Matrix

PubMed Central

Kanyas, Selin; Aydın, Derya; Kizilel, Riza; Demirel, A. Levent; Kizilel, Seda

2014-01-01

Polymer composites consisted of small hydrophilic pockets homogeneously dispersed in a hydrophobic polymer matrix are important in many applications where controlled release of the functional agent from the hydrophilic phase is needed. As an example, a release of biomolecules or drugs from therapeutic formulations or release of salt in anti-icing application can be mentioned. Here, we report a method for preparation of such a composite material consisted of small KCOOH salt pockets distributed in the styrene-butadiene-styrene (SBS) polymer matrix and demonstrate its effectiveness in anti-icing coatings. The mixtures of the aqueous KCOOH and SBS-cyclohexane solutions were firstly stabilized by adding silica nanoparticles to the emulsions and, even more, by gelation of the aqueous phase by agarose. The emulsions were observed in optical microscope to check its stability in time and characterized by rheological measurements. The dry composite materials were obtained via casting the emulsions onto the glass substrates and evaporations of the organic solvent. Composite polymer films were characterized by water contact angle (WCA) measurements. The release of KCOOH salt into water and the freezing delay experiments of water droplets on dry composite films demonstrated their anti-icing properties. It has been concluded that hydrophobic and thermoplastic SBS polymer allows incorporation of the hydrophilic pockets/phases through our technique that opens the possibility for controlled delivering of anti-icing agents from the composite. PMID:24516593

Landscape Change and Microbial Response in the McMurdo Dry Valleys, Antarctica: Preliminary Results

NASA Astrophysics Data System (ADS)

Fountain, A. G.; Levy, J.; Gooseff, M. N.; Van Horn, D. J.; Obryk, M.; Pettersson, R.; Telling, J. W.; Glennie, C. L.

2017-12-01

Permafrost in the McMurdo Dry Valleys (MDV), Antarctica is ubiquitous with active layer depths ranging from a few cm at the highest elevations to 1 m near sea level. Although many landscapes in this region have been considered stable over millennia, ad-hoc field observations have documented extreme geomorphic changes in the valley bottoms over the past decade. To assess these changes across the region, we compared a lidar dataset surveyed in the austral summers of 2001-2002 against one surveyed in 2014-2015. Results showed that the vertical resolution of the surveys was < 0.1m. However, a mounting bias of the NASA sensor reduced the resolution of the elevation differences and we ignored differences < ±0.25 m. The surveys revealed large (>1m) landscape changes, including stream channel incision into buried ice deposits (implying the advection of heat by stream water locally degrades thermokarst) and slope failures in thermokarst landforms from block failure and insolation-driven retreat. Smaller changes (<0.5 m) were observed in stream channels where lateral bank erosion intercepted buried ice, or in thermokarst ponds. The magnitude and rate of change is much larger than observed previously in this otherwise stable and slowly changing environment. Biological surveys and experimental manipulations show that wetted soils host microbial communities different from those hosted by adjacent dry soils, and are hotspots of biodiversity highly susceptible to changing physical conditions. In all cases field-checked, the association of sediment and rock debris blanketing buried ice was noted, indicating these are the most vulnerable landscapes to climate warming. Ground penetrating radar mapping of buried ice showed, however, that not all buried ice is associated with landscape change due to the depth of burial, slope, and proximity to stream water. Similarly, modeling of soil temperatures suggests a spatial heterogeneity in warming rates across the valley bottom, as a consequence of microclimatic influences, topographic shading and moisture content. Collectively, these conditions imply that landscapes in the MDV will become progressively unstable in a warming future as heat is increasingly transported to greater depths in the valley floor, and that these changes are likely to significantly impact the associated microbial communities.

A novel polymer extrusion micropelletization process

NASA Astrophysics Data System (ADS)

Aquite, William

Polymer micropellets provide a variety of potential applications for different processes in the polymer industry. Conventional pellets are in the size range of 2.5 mm to 5 mm, while micropellets are at least ten times smaller, in the size range of 50 μm to 1000 μm. The potential benefits to a processor using micropellets include: high surface to volume ratio, high bulk density, fast and even melting rates in extrusion, improved dry flow properties, faster injection molding cycles, and consequently lower energy consumption during processing. More specialized sintering processes that require polymer powders, such as selective sintering techniques, microporous plastics parts manufacturing, and other powder sintering methods would benefit from the production of polymer micropellets since these exhibit the advantages of pellets yet have a lower average size. This work focuses on the study of a technique developed at the Polymer Engineering Center. The technique uses a microcapillary die for the production of micropellets by causing instabilities in extruded polymer threads deformed using an air stream. Tuning of process conditions allow the development of surface disturbances that promote breakup of the threads into pellets, which are subsequently cooled and collected. Although micropellets with high sphericity and a narrow size distribution can be produced using this technique, minimal changes in process conditions also lead to the production of lenticular pellets as well as pellets, fibers and threads with a wide range of size and shape distributions. This work shows how changing processing conditions achieve a variety of shapes and sizes of micropellets, broadening its application for the production of powders from a variety of polymer resins. Different approaches were used, including dimensional analysis and numerical simulation of the micropelletization process. This research reveals the influence of non-linear viscoelastic effects on the dispersion of a polymer thread through surface disturbances. Furthermore, this research reveals how processing parameters can influence the quality of the produced micropellet. Through this work, an economically feasible technique was developed that can produce the raw material for processors that depend on polymer powders that will deliver ideally shaped and distributed micropellets.

Ice Recrystallization in a Solution of a Cryoprotector and Its Inhibition by a Protein: Synchrotron X-Ray Diffraction Study.

PubMed

Zakharov, Boris; Fisyuk, Alexander; Fitch, Andy; Watier, Yves; Kostyuchenko, Anastasia; Varshney, Dushyant; Sztucki, Michael; Boldyreva, Elena; Shalaev, Evgenyi

2016-07-01

Ice formation and recrystallization is a key phenomenon in freezing and freeze-drying of pharmaceuticals and biopharmaceuticals. In this investigation, high-resolution synchrotron X-ray diffraction is used to quantify the extent of disorder of ice crystals in binary aqueous solutions of a cryoprotectant (sorbitol) and a protein, bovine serum albumin. Ice crystals in more dilute (10 wt%) solutions have lower level of microstrain and larger crystal domain size than these in more concentrated (40 wt%) solutions. Warming the sorbitol-water mixtures from 100 to 228 K resulted in partial ice melting, with simultaneous reduction in the microstrain and increase in crystallite size, that is, recrystallization. In contrast to sorbitol solutions, ice crystals in the BSA solutions preserved both the microstrain and smaller crystallite size on partial melting, demonstrating that BSA inhibits ice recrystallization. The results are consistent with BSA partitioning into quasi-liquid layer on ice crystals but not with a direct protein-ice interaction and protein sorption on ice surface. The study shows for the first time that a common (i.e., not-antifreeze) protein can have a major impact on ice recrystallization and also presents synchrotron X-ray diffraction as a unique tool for quantification of crystallinity and disorder in frozen aqueous systems. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Effects of residual feed intake classification and method of alfalfa processing on ewe intake and growth.

PubMed

Redden, R R; Surber, L M M; Grove, A V; Kott, R W

2014-02-01

The objective of this research was to evaluate the effects of residual feed intake (RFI) determined under ad libitum feeding conditions on DMI and performance of yearling ewes fed either chopped or pelleted alfalfa hay. In Exp. 1, 45 ewe-lambs had ad libitum access to a pelleted grower diet for 63 d and individual DMI was determined using an electronic feed delivery system. Residual feed intake values were assigned to each ewe-lamb as a measure of feed efficiency. Sixteen ewe-lambs with the most positive RFI values were classified as high RFI (inefficient) and 16 ewe-lambs with the most negative RFI values were classified as low RFI (efficient). In Exp. 2, half of the ewes from each efficiency group were placed into 1 of 2 pens and provided ad libitum access to either pelleted or chopped alfalfa hay. Individual DMI was again determined using an electronic feed delivery system. Body weight, LM area (LMA), and 12th-rib back fat thickness (BF) were measured at the beginning and end of both experiments. In Exp. 1, DMI by ewe-lambs in the low RFI group was 9% less (P = 0.01) than by ewe-lambs in the high RFI group (2.21 vs. 2.43 kg/d); however, ADG and initial and final BW, LMA, and BF did not differ (P > 0.27) among RFI groups. In Exp. 2, there were no feed processing × RFI group interactions (P > 0.14) for any trait. By design, RFI values were lower (P < 0.01) by yearling ewes in the low than high RFI group (-0.27 vs. 0.27); however, RFI values did not differ (P = 1.0) between yearling ewes fed chopped versus pelleted alfalfa. Dry matter intake was 22% less (P < 0.01) by yearling ewes in the low than high RFI group (2.5 vs. 3.2 kg/d) and 59% less (P < 0.01) by yearling ewes fed chopped versus pelleted alfalfa (2.2 vs. 3.5 kg/d). Initial and final BW, ADG, and G:F did not differ (P > 0.45) between RFI groups but were greater (P < 0.01) by yearling ewes fed pelleted alfalfa compared to chopped alfalfa. Final LMA did not differ (P = 0.77) between RFI groups, but final BF tended to be greater (P = 0.06) for high than low RFI yearling ewes (0.63 vs. 0.57 cm). Final LMA and BF were greater (P < 0.01) by yearling ewes fed pelleted than chopped alfalfa. Low RFI ewes had lower DMI and BF compared to high RFI ewes. Ewe efficiency as determined by RFI was repeatable on subsequent forage based diets; however, differences in intake and efficiency were more apparent when alfalfa was pelleted.

Coastal-change and glaciological map of the Ross Island area, Antarctica

USGS Publications Warehouse

Ferrigno, Jane G.; Foley, Kevin M.; Swithinbank, Charles; Williams, Richard S.

2010-01-01

Reduction in the area and volume of Earth?s two polar ice sheets is intricately linked to changes in global climate and to the resulting rise in sea level. Measurement of changes in area and mass balance of the Antarctic ice sheet was given a very high priority in recommendations by the Polar Research Board of the National Research Council. On the basis of these recommendations, the U.S. Geological Survey used its archive of satellite images to document changes in the cryospheric coastline of Antarctica and analyze the glaciological features of the coastal regions. The Ross Island area map is bounded by long 141? E. and 175? E. and by lat 76? S. and 81? S. The map covers the part of southern Victoria Land that includes the northwestern Ross Ice Shelf, the McMurdo Ice Shelf, part of the polar plateau and Transantarctic Mountains, the McMurdo Dry Valleys, northernmost Shackleton Coast, Hillary Coast, the southern part of Scott Coast, and Ross Island. Little noticeable change has occurred in the ice fronts on the map, so the focus is on glaciological features. In the western part of the map area, the polar plateau of East Antarctica, once thought to be a featureless region, has subtle wavelike surface forms (megadunes) and flow traces of glaciers that originate far inland and extend to the coast or into the Ross Ice Shelf. There are numerous outlet glaciers. Glaciers drain into the McMurdo Dry Valleys, through the Transantarctic Mountains into the Ross Sea, or into the Ross Ice Shelf. Byrd Glacier is the largest. West of the Transantarctic Mountains are areas of blue ice, readily identifiable on Landsat images, that have been determined to be prime areas for finding meteorites. Three subglacial lakes have been identified in the map area. Because McMurdo Station, the main U.S. scientific research station in Antarctica, is located on Ross Island in the map area, many of these and other features in the area have been studied extensively. The paper version of this map is available for purchase from the USGS Store.

Evaluating the process parameters of the dry coating process using a 2(5-1) factorial design.

PubMed

Kablitz, Caroline Désirée; Urbanetz, Nora Anne

2013-02-01

A recent development of coating technology is dry coating, where polymer powder and liquid plasticizer are layered on the cores without using organic solvents or water. Several studies evaluating the process were introduced in literature, however, little information about the critical process parameters (CPPs) is given. Aim of the study was the investigation and optimization of CPPs with respect to one of the critical quality attributes (CQAs), the coating efficiency of the dry coating process in a rotary fluid bed. Theophylline pellets were coated with hydroxypropyl methylcellulose acetate succinate as enteric film former and triethyl citrate and acetylated monoglyceride as plasticizer. A 2(5-1) design of experiments (DOEs) was created investigating five independent process parameters namely coating temperature, curing temperature, feeding/spraying rate, air flow and rotor speed. The results were evaluated by multilinear regression using the software Modde(®) 7. It is shown, that generally, low feeding/spraying rates and low rotor speeds increase coating efficiency. High coating temperatures enhance coating efficiency, whereas medium curing temperatures have been found to be optimum in terms of coating efficiency. This study provides a scientific base for the design of efficient dry coating processes with respect to coating efficiency.

Mitigation of methane production from cattle by feeding cashew nut shell liquid.

PubMed

Shinkai, T; Enishi, O; Mitsumori, M; Higuchi, K; Kobayashi, Y; Takenaka, A; Nagashima, K; Mochizuki, M; Kobayashi, Y

2012-09-01

The effects of cashew nut shell liquid (CNSL) feeding on methane production and rumen fermentation were investigated by repeatedly using 3 Holstein nonlactating cows with rumen fistulas. The cows were fed a concentrate and hay diet (6:4 ratio) for 4 wk (control period) followed by the same diet with a CNSL-containing pellet for the next 3 wk (CNSL period). Two trials were conducted using CNSL pellets blended with only silica (trial 1) or with several other ingredients (trial 2). Each pellet type was fed to cows to allow CNSL intake at 4 g/100 kg of body weight per day. Methane production was measured in a respiration chamber system, and energy balance, nutrient digestibility, and rumen microbial changes were monitored. Methane production per unit of dry matter intake decreased by 38.3 and 19.3% in CNSL feeding trials 1 and 2, respectively. Energy loss as methane emission decreased from 9.7 to 6.1% (trial 1) and from 8.4 to 7.0% (trial 2) with CNSL feeding, whereas the loss to feces (trial 1) and heat production (trial 2) increased. Retained energy did not differ between the control and CNSL periods. Digestibility of dry matter and gross energy decreased with CNSL feeding in trial 1, but did not differ in trial 2. Feeding CNSL caused a decrease in acetate and total short-chain fatty acid levels and an increase in propionate proportion in both trials. Relative copy number of methyl coenzyme-M reductase subunit A gene and its expression decreased with CNSL feeding. The relative abundance of fibrolytic or formate-producing species such as Ruminococcus flavefaciens, Butyrivibrio fibrisolvens, and Treponema bryantii decreased, but species related to propionate production, including Prevotella ruminicolla, Selenomonas ruminantium, Anaerovibrio lipolytica, and Succinivibrio dextrinosolvens, increased. If used in a suitable formulation, CNSL acts as a potent methane-inhibiting and propionate-enhancing agent through the alteration of rumen microbiota without adversely affecting feed digestibility. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Polycyclic aromatic hydrocarbons in US and Swedish smokeless tobacco products

PubMed Central

2013-01-01

Background Debate about the health implications of using smokeless tobacco products (STPs) has prompted considerable interest in characterising their levels of toxic and carcinogenic components. In the present study seventy smokeless tobacco products from the US and Sweden, categorized as chewing tobacco, dry and moist snuff, hard and soft pellets, plug, and loose and portion snus, were analysed for twenty one polycyclic aromatic hydrocarbons (PAHs). The tested brands represented 80-90% of the 2008 market share for the major STP categories in these two countries. Results There were significant differences in the total and individual PAH concentrations in the different styles of product. Substantially higher levels of total PAHs (10–60 fold) were found in moist and dry snuff and soft pellets than in the other smokeless tobacco styles. The individual PAH concentrations followed the same patterns as total PAHs except for naphthalene, for which the highest concentrations were found in snus and moist snuff. Good correlations were obtained between benzo[a]pyrene (B[a]P) and all the other PAHs except naphthalene, 1-methylnaphthalene and 2-methylnaphthalene, providing evidence for the first time that it can be used as a good marker for PAHs in STPs. Results were generally in good agreement with two previous studies of PAHs in STPs, except for naphthalene for which significantly lower concentrations were found than previously reported. Analysis of the ratios of different PAHs confirmed that the use of fire-cured tobaccos in the snuffs and soft pellet were the major source of PAHs in these product styles, and provided, for the first time, some indications as to the source of PAHs in the other STP styles, including petrogenic and other combustion sources. Conclusions This study confirms the presence of PAHs in STPs, and identifies substantial differences between the levels in different STP categories. Since previous studies of naphthalene concentrations in STPs differed so markedly from those found in this study, it is recommended that further work on PAH determination is undertaken to investigate the source of this discrepancy. PMID:24011230

Controlled drug delivery to the lung: Influence of hyaluronic acid solution conformation on its adsorption to hydrophobic drug particles.

PubMed

Rouse, J J; Whateley, T L; Thomas, M; Eccleston, G M

2007-02-07

This work reports investigations into the interaction and adsorption of the hydrophilic polymer hyaluronic acid (HA) onto the surface of the hydrophobic corticosteroid drug fluticasone propionate (FP). The eventual aim is to formulate a bioadhesive pulmonary drug delivery system with prolonged action that avoids rapid clearance from the lungs by the mucociliary escalator. Adsorption isotherms detailing the adsorption of HA from aqueous HA solution concentrations ranging from 0.14 to 0.0008% (w/v) to a fixed FP particle concentration of 0.1% (w/v) were investigated. The method of preparing FP particles with HA molecules adsorbed on their surfaces (FP/HA particles) involved suspension of the FP either in hydrated HA solution or in water followed by addition of solid HA, centrifugation of the solids to form a pellet, washing the pellet several times with water until no HA was found in the supernatant and then freeze drying the suspension obtained by dispersing the final pellet. The freeze dried powder was then analysed for adsorbed HA using a Stains-all assay. The influence of order of addition of HA to FP, time for the adsorption process, and temperature of preparation on the adsorption isotherms was investigated. The non-equilibrium adsorption isotherms produced generally followed the same trend, in that as the HA solution concentration increased, the amount of HA adsorbed increased to a maximum at a solution concentration of approximately 0.1% (w/v) and then decreased. The maxima in the adsorption isotherms were close to the change from secondary to tertiary conformation in the HA solutions. Below the maxima, adsorption occurred via interaction of FP with the hydrophobic patches along the HA chains in the secondary structures. Above the maxima, secondary HA molecules aggregate in solution to form tertiary network structures. Adsorption from tertiary structure was reduced because strong interactions between the HA molecules limited the availability of hydrophobic patches for adsorption of HA onto FP. The influence of preparation variables on adsorption was also related to the availability of hydrophobic patches for adsorption.

Evaluation of methodological aspects of digestibility measurements in ponies fed different haylage to concentrate ratios.

PubMed

Schaafstra, F J W C; van Doorn, D A; Schonewille, J T; van Riet, M M J; Visser, P; Blok, M C; Hendriks, W H

2017-11-01

Methodological aspects of digestibility measurements were studied in four Welsh pony geldings consuming haylage-based diets with increasing proportions of a pelleted concentrate according to a 4×4 Latin square design experiment. Ponies were fed four experimental, iso-energetic (net energy (NE) basis) diets (i.e. 22 MJ NE/day) with increasing proportions of a pelleted concentrate (C) in relation to haylage (H). The absolute amounts of diet dry matter fed per day were 4.48 kg of H (100H), 3.36 and 0.73 kg of H and C (75H25C), 2.24 and 1.45 kg of H and C (50H50C) and 1.12 and 2.17 kg of H and C (25H75C). Diets were supplemented with minerals, vitamins and TiO2 (3.7 g Ti/day). Voluntary voided faeces were quantitatively collected daily during 10 consecutive days and analysed for moisture, ash, ADL, acid-insoluble ash (AIA) and Ti. A minimum faeces collection period of 6 consecutive days, along with a 14-day period to adapt the animals to the diets and become accustomed to the collection procedure, is recommended to obtain accurate estimations on dry matter digestibility and organic matter digestibility (OMD) in equids fed haylage-based diets supplemented with concentrate. In addition, the recovery of AIA, ADL and Ti was determined and evaluated. Mean faecal recovery over 10 consecutive days across diets for AIA, ADL and Ti was 124.9% (SEM 2.9), 108.7% (SEM 2.0) and 97.5% (SEM 0.9), respectively. Cumulative faecal recovery of AIA significantly differed between treatments, indicating that AIA is inadequate to estimate the OMD in equines. In addition, evaluation of the CV of mean cumulative faecal recoveries obtained by AIA, ADL and Ti showed greater variations in faecal excretion of AIA (9.1) and ADL (7.4) than Ti (3.7). The accuracy of prediction of OMD was higher with the use of Ti than ADL. The use of Ti is preferred as a marker in digestibility trials in equines fed haylage-based diets supplemented with increasing amounts of pelleted concentrate.

Multi-Sensor Mud Detection

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Matthies, Larry H.

2010-01-01

Robust mud detection is a critical perception requirement for Unmanned Ground Vehicle (UGV) autonomous offroad navigation. A military UGV stuck in a mud body during a mission may have to be sacrificed or rescued, both of which are unattractive options. There are several characteristics of mud that may be detectable with appropriate UGV-mounted sensors. For example, mud only occurs on the ground surface, is cooler than surrounding dry soil during the daytime under nominal weather conditions, is generally darker than surrounding dry soil in visible imagery, and is highly polarized. However, none of these cues are definitive on their own. Dry soil also occurs on the ground surface, shadows, snow, ice, and water can also be cooler than surrounding dry soil, shadows are also darker than surrounding dry soil in visible imagery, and cars, water, and some vegetation are also highly polarized. Shadows, snow, ice, water, cars, and vegetation can all be disambiguated from mud by using a suite of sensors that span multiple bands in the electromagnetic spectrum. Because there are military operations when it is imperative for UGV's to operate without emitting strong, detectable electromagnetic signals, passive sensors are desirable. JPL has developed a daytime mud detection capability using multiple passive imaging sensors. Cues for mud from multiple passive imaging sensors are fused into a single mud detection image using a rule base, and the resultant mud detection is localized in a terrain map using range data generated from a stereo pair of color cameras.

9 CFR 3.101 - Facilities, general.

Code of Federal Regulations, 2014 CFR

2014-01-01

... measures, on all sides of the enclosure not contained by dry land to fulfill the requirements of this.../or iced coolers for under 12 hours) must be used for perishable food. No substances that are known to...

9 CFR 3.101 - Facilities, general.

Code of Federal Regulations, 2011 CFR

2011-01-01

... measures, on all sides of the enclosure not contained by dry land to fulfill the requirements of this.../or iced coolers for under 12 hours) must be used for perishable food. No substances that are known to...

9 CFR 3.101 - Facilities, general.

Code of Federal Regulations, 2013 CFR

2013-01-01

... measures, on all sides of the enclosure not contained by dry land to fulfill the requirements of this.../or iced coolers for under 12 hours) must be used for perishable food. No substances that are known to...

9 CFR 3.101 - Facilities, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

... measures, on all sides of the enclosure not contained by dry land to fulfill the requirements of this.../or iced coolers for under 12 hours) must be used for perishable food. No substances that are known to...

Advanced Initiation Systems Manufacturing Level 2 Milestone Completion Summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chow, R; Schmidt, M

2009-10-01

Milestone Description - Advanced Initiation Systems Detonator Design and Prototype. Milestone Grading Criteria - Design new generation chip slapper detonator and manufacture a prototype using advanced manufacturing processes, such as all-dry chip metallization and solvent-less flyer coatings. The advanced processes have been developed for manufacturing detonators with high material compatibility and reliability to support future LEPs, e.g. the B61, and new weapons systems. Perform velocimetry measurements to determine slapper velocity as a function of flight distance. A prototype detonator assembly and stripline was designed for low-energy chip slappers. Pictures of the prototype detonator and stripline are shown. All-dry manufacturing processesmore » were used to address compatibility issues. KCP metallized the chips in a physical vapor deposition system through precision-aligned shadow masks. LLNL deposited a solvent-less polyimide flyer with a processes called SLIP, which stands for solvent-less vapor deposition followed by in-situ polymerization. LANL manufactured the high-surface-area (HSA) high explosive (HE) pellets. Test fires of two chip slapper designs, radius and bowtie, were performed at LLNL in the High Explosives Application Facility (HEAF). Test fires with HE were conducted to establish the threshold firing voltages. pictures of the chip slappers before and after test fires are shown. Velocimetry tests were then performed to obtain slapper velocities at or above the threshold firing voltages. Figure 5 shows the slapper velocity as a function of distance and time at the threshold voltage, for both radius and bowtie bridge designs. Both designs were successful at initiating the HE at low energy levels. Summary of Accomplishments are: (1) All-dry process for chip manufacture developed; (2) Solventless process for slapper materials developed; (3) High-surface area explosive pellets developed; (4) High performance chip slappers developed; (5) Low-energy chip slapper detonator designs; and (6) Low-voltage threshold chip slapper detonator demonstrated.« less

Stabilities of Dried Suspensions of Influenza Virus Sealed in a Vacuum or Under Different Gases

PubMed Central

Greiff, Donald; Rightsel, Wilton A.

1969-01-01

Suspensions of purified influenza virus, dried to a 1.4% content of residual moisture by sublimation of ice in vacuo, were sealed in a vacuum or under different gases of high purity. The stabilities of the several preparations were determined by an accelerated storage test. Based on the times predicted for the dried preparations stored at different temperatures to lose 1 log of infectivity titer, the order of stabilities in relation to sealing in vacuum or under different gases was as follows: helium > hydrogen > vacuum > argon > nitrogen > oxygen > carbon dioxide. Images PMID:5797938

Mechanisms of basal ice formation in polar glaciers: An evaluation of the apron entrainment model

NASA Astrophysics Data System (ADS)

Fitzsimons, Sean; Webb, Nicola; Mager, Sarah; MacDonell, Shelley; Lorrain, Regi; Samyn, Denis

2008-06-01

Previous studies of polar glaciers have argued that basal ice can form when these glaciers override and entrain ice marginal aprons that accumulate adjacent to steep ice cliffs. To test this idea, we have studied the morphology, structure, composition, and deformation of the apron and basal ice at the terminus of Victoria Upper Glacier in the McMurdo dry valleys, which are located on the western coast of the Ross Sea at 77°S in southern Victoria Land, Antarctica. Our results show that the apron has two structural elements: an inner element that consists of strongly foliated ice that has a steep up-glacier dip, and an outer element that lacks a consistent foliation and has a down-glacier, slope-parallel dip. Although strain measurements show that the entire apron is deforming, the inner element is characterized by high strain rates, whereas relatively low rates of strain characterize the outer part of the apron. Co-isotopic analyses of the ice, together with analysis of solute chemistry and sedimentary characteristics, show that the apron is compositionally different from the basal ice. Our observations show that aprons may become deformed and partially entrained by advancing glaciers. However, such an ice marginal process does not provide a satisfactory explanation for the origin of basal ice observed at the ice margin. Our interpretation of the origin of basal ice is that it is formed by subglacial processes, which are likely to include deformation and entrainment of subglacial permafrost.

Sink or Swim: Ions and Organics at the Ice-Air Interface.

PubMed

Hudait, Arpa; Allen, Michael T; Molinero, Valeria

2017-07-26

The ice-air interface is an important locus of environmental chemical reactions. The structure and dynamics of the ice surface impact the uptake of trace gases and kinetics of reactions in the atmosphere and snowpack. At tropospheric temperatures, the ice surface is partially premelted. Experiments indicate that ions increase the liquidity of the ice surface but hydrophilic organics do not. However, it is not yet known the extent of the perturbation solutes induce at the ice surface and what is the role of the disordered liquid-like layer in modulating the interaction between solutes and their mobility and aggregation at the ice surface. Here we use large-scale molecular simulations to investigate the effect of ions and glyoxal, one of the most abundant oxygenated volatile organic compounds in the atmosphere, on the structure, dynamics, and solvation properties of the ice surface. We find that the premelted surface of ice has unique solvation properties, different from those of liquid water. The increase in surface liquidity resulting from the hydration of ions leads to a water-mediated attraction of ions at the ice surface. Glyoxal molecules, on the other hand, perturb only slightly the surface of ice and do not experience water-driven attraction. They nonetheless accumulate as dry agglomerates at the ice surface, driven by direct interactions between the organic molecules. The enhanced attraction and clustering of ions and organics at the ice surface may play a significant role in modulating the mechanism and rate of heterogeneous chemical reactions occurring at the surface of atmospheric ice particles.

Bibliography on Cold Regions Science and Technology Volume 53, Part 2

DTIC Science & Technology

1999-12-01

A.T. Claud, C. 53-1504 Interaction of ice floes with ships on offshore structures Case study of antarctic mesolow [1995, eng] 53-329 Coffey, M.T. [1992...in a dry-snow Dethloff, K Biogeochemistry of antarctic sea ice: a case study on avalanche [1998, eng] 53-2018 Climate variability in a nonlinear...concrete with respect to Effect of the Endicott Causeway on the population of Ferguson, M.E. frost resistance: a case study [1998, eng] 53-952 broad

Relationship between dissolved organic matter quality and microbial community composition across polar glacial environments.

PubMed

Smith, H J; Dieser, M; McKnight, D M; SanClements, M D; Foreman, C M

2018-05-14

Vast expanses of Earth's surface are covered by ice, with microorganisms in these systems affecting local and global biogeochemical cycles. We examined microbial assemblages from habitats fed by glacial meltwater within the McMurdo Dry Valleys, Antarctica, and on the west Greenland Ice Sheet, (GrIS) evaluating potential physicochemical factors explaining trends in community structure. Microbial assemblages present in the different Antarctic dry valley habitats were dominated by Sphingobacteria and Flavobacteria, while Gammaproteobacteria and Sphingobacteria prevailed in west GrIS supraglacial environments. Microbial assemblages clustered by location (Canada Glacier, Cotton Glacier, west GrIS) and were separated by habitat type (i.e. ice, cryoconite holes, supraglacial lakes, sediment, and stream water). Community dissimilarities were strongly correlated with dissolved organic matter (DOM) quality. Microbial meltwater assemblages were most closely associated with different protein-like components of the DOM pool. Microbes in environments with mineral particles (i.e. stream sediments, cryoconite holes) were linked to DOM containing more humic-like fluorescence. Our results demonstrate the establishment of distinct microbial communities within ephemeral glacial meltwater habitats, with DOM-microbe interactions playing an integral role in shaping communities on local and polar spatial scales.

Glacial geomorphic evidence for a late climatic change on Mars

NASA Technical Reports Server (NTRS)

Kargel, J. S.; Strom, R. G.

1992-01-01

In a series of preliminary reports, we documented evidence of former glacial epochs on Mars. Apparent glacial landforms seemed to be concentrated primarily at middle to high southern latitudes. We now have additional evidence supporting the view that Martian glaciation appears to have been more extensive than previously recognized. The growth and collapse of ice sheets on Mars seems closely analogous to the growth and decline of Earth's great Pleistocene ice sheets. This implies that climate change was probably somewhat comparable on the two planets, although in the case of Mars the entire planet seems to have changed rapidly to a cold, dry present-day environment after the collapse of the ice sheets.

Modeling of surface roughness effects on glaze ice accretion

NASA Technical Reports Server (NTRS)

Hansman, R. John, Jr.; Yamaguchi, Keiko; Berkowitz, Brian M.; Potapczuk, Mark

1990-01-01

A series of experimental investigations focused on studying the cause and effect of roughness on accreting glaze ice surfaces were conducted. Detailed microvideo observations were made of glaze ice accretions on 1 to 4 inch diameter cylinders in three icing wind tunnels (the Data Products of New England six inch test facility, the NASA Lewis Icing Research Tunnel, and the B. F. Goodrich Ice Protection Research Facility). Infrared thermal video recordings were made of accreting ice surfaces in the Goodrich facility. Distinct zones of surface water behavior were observed; a smooth wet zone in the stagnation region with a uniform water film; a rough zone where surface tension effects caused coalescence of surface water into stationary beads; a horn zone where roughness elements grow into horn shapes; a runback zone where surface water ran back as rivulets; and a dry zone where rime feathers formed. The location of the transition from the smooth to the rough zone was found to migrate with time towards the stagnation point. The behavior of the transition appeared to be controlled by boundary layer transition and bead formation mechanisms at the interface between the smooth and rough zones. Regions of wet ice growth and enhanced heat transfer were clearly visible in the infrared video recordings of glaze ice surfaces. A simple multi-zone modification to the current glaze ice accretion model was proposed to include spatial variability in surface roughness.

Preventing Ice Before it Forms

NASA Technical Reports Server (NTRS)

2006-01-01

In the late 1990s, a team of engineers at Ames Research Center invented an anti-icing fluid to keep ice from building up on airplane wings. Ice on wings can be a serious safety hazard, especially during takeoff, when a sheet of ice the thickness of a compact disc can reduce lift by 25 percent or more. The typical approach to clearing off the ice is to use a deicing solution once the ice has built up. The fluid created by the Ames team, though, when applied to a dry surface, prevents the ice from even forming a surface bond, which saves deicing time and money, while also preventing excessive use of chemical solvents. If, however, the solution is not applied before ice forms, it also serves as a traditional deicing formula. The formula contains propylene glycol, which has a very low freezing point, and a thickener, which helps the fluid adhere to the surface. Ice gathers on top of the formula, and then it can be wiped off with little effort. This thickening agent, a pseudo-plastic, sprays on as a liquid, like lemonade, gels like a lemon sherbet, turns back to a liquid when wiped, and then gels again into its sherbet consistency when left to solidify. The sherbet-gel stage is especially important when the formula is sprayed onto a vertical or steeped surface, as it clings better than a liquid would.

Radiometric 81Kr dating identifies 120,000-year-old ice at Taylor Glacier, Antarctica

PubMed Central

Buizert, Christo; Baggenstos, Daniel; Jiang, Wei; Purtschert, Roland; Petrenko, Vasilii V.; Lu, Zheng-Tian; Müller, Peter; Kuhl, Tanner; Lee, James; Severinghaus, Jeffrey P.; Brook, Edward J.

2014-01-01

We present successful 81Kr-Kr radiometric dating of ancient polar ice. Krypton was extracted from the air bubbles in four ∼350-kg polar ice samples from Taylor Glacier in the McMurdo Dry Valleys, Antarctica, and dated using Atom Trap Trace Analysis (ATTA). The 81Kr radiometric ages agree with independent age estimates obtained from stratigraphic dating techniques with a mean absolute age offset of 6 ± 2.5 ka. Our experimental methods and sampling strategy are validated by (i) 85Kr and 39Ar analyses that show the samples to be free of modern air contamination and (ii) air content measurements that show the ice did not experience gas loss. We estimate the error in the 81Kr ages due to past geomagnetic variability to be below 3 ka. We show that ice from the previous interglacial period (Marine Isotope Stage 5e, 130–115 ka before present) can be found in abundance near the surface of Taylor Glacier. Our study paves the way for reliable radiometric dating of ancient ice in blue ice areas and margin sites where large samples are available, greatly enhancing their scientific value as archives of old ice and meteorites. At present, ATTA 81Kr analysis requires a 40–80-kg ice sample; as sample requirements continue to decrease, 81Kr dating of ice cores is a future possibility. PMID:24753606