Defense Waste Processing Facility (DWPF) Viscosity Model: Revisions for Processing High TiO 2 Containing Glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C. M.; Edwards, T. B.

Radioactive high-level waste (HLW) at the Savannah River Site (SRS) has successfully been vitrified into borosilicate glass in the Defense Waste Processing Facility (DWPF) since 1996. Vitrification requires stringent product/process (P/P) constraints since the glass cannot be reworked once it is poured into ten foot tall by two foot diameter canisters. A unique “feed forward” statistical process control (SPC) was developed for this control rather than statistical quality control (SQC). In SPC, the feed composition to the DWPF melter is controlled prior to vitrification. In SQC, the glass product would be sampled after it is vitrified. Individual glass property-composition modelsmore » form the basis for the “feed forward” SPC. The models transform constraints on the melt and glass properties into constraints on the feed composition going to the melter in order to guarantee, at the 95% confidence level, that the feed will be processable and that the durability of the resulting waste form will be acceptable to a geologic repository. The DWPF SPC system is known as the Product Composition Control System (PCCS). The DWPF will soon be receiving wastes from the Salt Waste Processing Facility (SWPF) containing increased concentrations of TiO 2, Na 2O, and Cs 2O . The SWPF is being built to pretreat the high-curie fraction of the salt waste to be removed from the HLW tanks in the F- and H-Area Tank Farms at the SRS. In order to process TiO 2 concentrations >2.0 wt% in the DWPF, new viscosity data were developed over the range of 1.90 to 6.09 wt% TiO 2 and evaluated against the 2005 viscosity model. An alternate viscosity model is also derived for potential future use, should the DWPF ever need to process other titanate-containing ion exchange materials. The ultimate limit on the amount of TiO 2 that can be accommodated from SWPF will be determined by the three PCCS models, the waste composition of a given sludge batch, the waste loading of the sludge batch, and the frit used for vitrification.« less

Defense waste processing facility (DWPF) liquids model: revisions for processing higher TIO 2 containing glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C. M.; Edwards, T. B.; Trivelpiece, C. L.

Radioactive high level waste (HLW) at the Savannah River Site (SRS) has successfully been vitrified into borosilicate glass in the Defense Waste Processing Facility (DWPF) since 1996. Vitrification requires stringent product/process (P/P) constraints since the glass cannot be reworked once it is poured into ten foot tall by two foot diameter canisters. A unique “feed forward” statistical process control (SPC) was developed for this control rather than statistical quality control (SQC). In SPC, the feed composition to the DWPF melter is controlled prior to vitrification. In SQC, the glass product would be sampled after it is vitrified. Individual glass property-compositionmore » models form the basis for the “feed forward” SPC. The models transform constraints on the melt and glass properties into constraints on the feed composition going to the melter in order to guarantee, at the 95% confidence level, that the feed will be processable and that the durability of the resulting waste form will be acceptable to a geologic repository. This report documents the development of revised TiO 2, Na 2O, Li 2O and Fe 2O 3 coefficients in the SWPF liquidus model and revised coefficients (a, b, c, and d).« less

Assessment of the Impact of a New Guanidine Suppressor In NGS on F/H Laboratory Analyses For DWPF and Saltstone MCU Transfers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.

2013-04-29

Implementation of the Next Generation Solvent (NGS) in the Modular Caustic-Side Solvent Extraction Unit (MCU) will now proceed with a new suppressor compound, 1,2,3-tris(3,7-dimethyloctyl)guanidine (TiDG), replacing the originally planned suppressor for NGS, 1,3-dicyclohexyl-2-(11-methyldodecyl) guanidine (DCiTG). The Savannah River National Laboratory (SRNL) was tasked with evaluating the potential impact to F/H Laboratory analyses supporting the Defense Waste Processing Facility (DWPF) Waste Acceptance Criteria (WAC) used to qualify transfers of MCU Strip Effluent (SE) into the facility and the Saltstone WAC used to qualify transfers of Tank 50 containing Decontaminated Salt Solution (DSS) from MCU into Saltstone. This assigned scope is coveredmore » by a Task Technical and Quality Assurance Plan (TTQAP). Previous impact evaluations were conducted when the DCiTG suppressor was planned for NGS and concluded that there was no impact to either the determination of MCU SE pH nor the analysis of Isopar® L carryover in the MCU SE and DSS streams. SRNL reported on this series of cross-check studies between the SRNL and F/H Laboratories. The change in suppressor from DCiTG to TiDG in the NGS should not impact the measurement of Isopar® L or pH in SE or DSS necessary to satisfy DWPF and Saltstone WAC (Tank 50) criteria, respectively. A statistical study of the low bias observed in Isopar® L measurements in both SRNL and F/H Laboratories may be necessary now that the final NGS composition is fixed in order to quantify the low bias so that a proper correction can be applied to measurements critical to the DWPF and Saltstone WACs. Depending upon the final DWPF WAC requirement put in place for SE pH, it could become necessary to implement an alternative ICP-AES measurement of boron. The current blended solvent system testing in SRNL should address any impacts to Isopar® L carryover into either the DSS or the SE. It is recommended that SRNL monitor the current blended solvent work underway with simulants in SRNL as well as any DWPF CPC testing done with the new SE stream to ascertain whether any need develops that could result in modification of any currently planned F/H Laboratory testing protocols.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, M. S.; Miller, D. H.; Fowley, M. D.

The Savannah River National Laboratory (SRNL) was tasked to support validation of the Defense Waste Processing Facility (DWPF) melter offgas flammability model for the nitric-glycolic (NG) flowsheet. The work supports Deliverable 4 of the DWPF & Saltstone Facility Engineering Technical Task Request (TTR)1 and is supplemental to the Cold Cap Evaluation Furnace (CEF) testing conducted in 2014.2 The Slurry-fed Melt Rate Furnace (SMRF) was selected for the supplemental testing as it requires significantly less resources than the CEF and could provide a tool for more rapid analysis of melter feeds in the future. The SMRF platform has been used previouslymore » to evaluate melt rate behavior of DWPF glasses, but was modified to accommodate analysis of the offgas stream. Additionally, the Melt Rate Furnace (MRF) and Quartz Melt Rate Furnace (QMRF) were utilized for evaluations. MRF data was used exclusively for melt behavior observations and REDuction/OXidation (REDOX) prediction comparisons and will be briefly discussed in conjunction with its support of the SMRF testing. The QMRF was operated similarly to the SMRF for the same TTR task, but will be discussed in a separate future report. The overall objectives of the SMRF testing were to; 1) Evaluate the efficacy of the SMRF as a platform for steady state melter testing with continuous feeding and offgas analysis; and 2) Generate supplemental melter offgas flammability data to support the melter offgas flammability modelling effort for DWPF implementation of the NG flowsheet.« less

EVALUATION OF THE IMPACT OF THE DEFENSE WASTE PROCESSING FACILITY (DWPF) LABORATORY GERMANIUM OXIDE USE ON RECYCLE TRANSFERS TO THE H-TANK FARM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C.; Laurinat, J.

2011-08-15

When processing High Level Waste (HLW) glass, the Defense Waste Processing Facility (DWPF) cannot wait until the melt or waste glass has been made to assess its acceptability, since by then no further changes to the glass composition and acceptability are possible. Therefore, the acceptability decision is made on the upstream feed stream, rather than on the downstream melt or glass product. This strategy is known as 'feed forward statistical process control.' The DWPF depends on chemical analysis of the feed streams from the Sludge Receipt and Adjustment Tank (SRAT) and the Slurry Mix Evaporator (SME) where the frit plusmore » adjusted sludge from the SRAT are mixed. The SME is the last vessel in which any chemical adjustments or frit additions can be made. Once the analyses of the SME product are deemed acceptable, the SME product is transferred to the Melter Feed Tank (MFT) and onto the melter. The SRAT and SME analyses have been analyzed by the DWPF laboratory using a 'Cold Chemical' method but this dissolution did not adequately dissolve all the elemental components. A new dissolution method which fuses the SRAT or SME product with cesium nitrate (CsNO{sub 3}), germanium (IV) oxide (GeO{sub 2}) and cesium carbonate (Cs{sub 2}CO{sub 3}) into a cesium germanate glass at 1050 C in platinum crucibles has been developed. Once the germanium glass is formed in that fusion, it is readily dissolved by concentrated nitric acid (about 1M) to solubilize all the elements in the SRAT and/or SME product for elemental analysis. When the chemical analyses are completed the acidic cesium-germanate solution is transferred from the DWPF analytic laboratory to the Recycle Collection Tank (RCT) where the pH is increased to {approx}12 M to be released back to the tank farm and the 2H evaporator. Therefore, about 2.5 kg/yr of GeO{sub 2}/year will be diluted into 1.4 million gallons of recycle. This 2.5 kg/yr of GeO{sub 2} may increase to 4 kg/yr when improvements are implemented to attain an annual canister production goal of 400 canisters. Since no Waste Acceptance Criteria (WAC) exists for germanium in the Tank Farm, the Effluent Treatment Project, or the Saltstone Production Facility, DWPF has requested an evaluation of the fate of the germanium in the caustic environment of the RCT, the 2H evaporator, and the tank farm. This report evaluates the effect of the addition of germanium to the tank farm based on: (1) the large dilution of Ge in the RCT and tank farm; (2) the solubility of germanium in caustic solutions (pH 12-13); (3) the potential of germanium to precipitate as germanium sodalites in the 2H Evaporator; and (4) the potential of germanium compounds to precipitate in the evaporator feed tank. This study concludes that the impacts of transferring up to 4 kg/yr germanium to the RCT (and subsequently the 2H evaporator feed tank and the 2H evaporator) results in <2 ppm per year (1.834 mg/L) which is the maximum instantaneous concentration expected from DWPF. This concentration is insignificant as most sodium germanates are soluble at the high pH of the feed tank and evaporator solutions. Even if sodium aluminosilicates form in the 2H evaporator, the Ge will likely substitute for some small amount of the Si in these structures and will be insignificant. It is recommended that the DWPF continue with their strategy to add germanium as a laboratory chemical to Attachment 8.2 of the DWPF Waste Compliance Plan (WCP).« less

Defense Waste Processing Facility (DWPF) Durability-Composition Models and the Applicability of the Associated Reduction of Constraints (ROC) Criteria for High TiO 2 Containing Glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C. M.; Edwards, T. B.; Trivelpiece, C. L.

Radioactive high-level waste (HLW) at the Savannah River Site (SRS) has successfully been vitrified into borosilicate glass in the DWPF since 1996. Vitrification requires stringent product/process (P/P) constraints since the glass cannot be reworked once it has been poured into ten foot tall by two foot diameter canisters. A unique “feed forward” statistical process control (SPC) was developed for this control rather than relying on statistical quality control (SQC). In SPC, the feed composition to the DWPF melter is controlled prior to vitrification. In SQC, the glass product would be sampled after it is vitrified. Individual glass property-composition models formmore » the basis for the “feed forward” SPC. The models transform constraints on the melt and glass properties into constraints on the feed composition going to the melter in order to determine, at the 95% confidence level, that the feed will be processable and that the durability of the resulting waste form will be acceptable to a geologic repository. The DWPF SPC system is known as the Product Composition Control System (PCCS). One of the process models within PCCS is known as the Thermodynamic Hydration Energy Reaction MOdel (THERMO™). The DWPF will soon be receiving increased concentrations of TiO 2-, Na 2O-, and Cs 2O-enriched wastes from the Salt Waste Processing Facility (SWPF). The SWPF has been built to pretreat the high-curie fraction of the salt waste to be removed from the HLW tanks in the F- and H-Area Tank Farms at the SRS. In order to validate the existing TiO 2 term in THERMO™ beyond 2.0 wt% in the DWPF, new durability data were developed over the target range of 2.00 to 6.00 wt% TiO 2 and evaluated against the 1995 durability model. The durability was measured by the 7-day Product Consistency Test. This study documents the adequacy of the existing THERMO™ terms. It is recommended that the modified THERMO™ durability models and the modified property acceptable region limits for the durability constraints be incorporated in the next revision of the technical bases for PCCS and then implemented into PCCS. It is also recommended that an reduction of constraints of 4 wt% Al 2O 3 be implemented with no restrictions on the amount of alkali in the glass for TiO 2 values ≥2 wt%. The ultimate limit on the amount of TiO 2 that can be accommodated from SWPF will be determined by the three PCCS models, the waste composition of a given sludge batch, the waste loading of the sludge batch, and the frit used for vitrification.« less

Crystallization in high level waste (HLW) glass melters: Savannah River Site operational experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, Kevin M.; Peeler, David K.; Kruger, Albert A.

2015-06-12

This paper provides a review of the scaled melter testing that was completed for design input to the Defense Waste Processing Facility (DWPF) melter. Testing with prototype melters provided the data to define the DWPF operating limits to avoid bulk (volume) crystallization in the un-agitated DWPF melter and provided the data to distinguish between spinels generated by refractory corrosion versus spinels that precipitated from the HLW glass melt pool. A review of the crystallization observed with the prototype melters and the full-scale DWPF melters (DWPF Melter 1 and DWPF Melter 2) is included. Examples of actual DWPF melter attainment withmore » Melter 2 are given. The intent is to provide an overview of lessons learned, including some example data, that can be used to advance the development and implementation of an empirical model and operating limit for crystal accumulation for a waste treatment and immobilization plant.« less

PROCESSING ALTERNATIVES FOR DESTRUCTION OF TETRAPHENYLBORATE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D; Thomas Peters, T; Samuel Fink, S

Two processes were chosen in the 1980's at the Savannah River Site (SRS) to decontaminate the soluble High Level Waste (HLW). The In Tank Precipitation (ITP) process (1,2) was developed at SRS for the removal of radioactive cesium and actinides from the soluble HLW. Sodium tetraphenylborate was added to the waste to precipitate cesium and monosodium titanate (MST) was added to adsorb actinides, primarily uranium and plutonium. Two products of this process were a low activity waste stream and a concentrated organic stream containing cesium tetraphenylborate and actinides adsorbed on monosodium titanate (MST). A copper catalyzed acid hydrolysis process wasmore » built to process (3, 4) the Tank 48H cesium tetraphenylborate waste in the SRS's Defense Waste Processing Facility (DWPF). Operation of the DWPF would have resulted in the production of benzene for incineration in SRS's Consolidated Incineration Facility. This process was abandoned together with the ITP process in 1998 due to high benzene in ITP caused by decomposition of excess sodium tetraphenylborate. Processing in ITP resulted in the production of approximately 1.0 million liters of HLW. SRS has chosen a solvent extraction process combined with adsorption of the actinides to decontaminate the soluble HLW stream (5). However, the waste in Tank 48H is incompatible with existing waste processing facilities. As a result, a processing facility is needed to disposition the HLW in Tank 48H. This paper will describe the process for searching for processing options by SRS task teams for the disposition of the waste in Tank 48H. In addition, attempts to develop a caustic hydrolysis process for in tank destruction of tetraphenylborate will be presented. Lastly, the development of both a caustic and acidic copper catalyzed peroxide oxidation process will be discussed.« less

Characterization of DWPF recycle condensate materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.; Adamson, D. J.; King, W. D.

2015-04-01

A Defense Waste Processing Facility (DWPF) Recycle Condensate Tank (RCT) sample was delivered to the Savannah River National Laboratory (SRNL) for characterization with particular interest in the concentration of I-129, U-233, U-235, total U, and total Pu. Since a portion of Salt Batch 8 will contain DWPF recycle materials, the concentration of I-129 is important to understand for salt batch planning purposes. The chemical and physical characterizations are also needed as input to the interpretation of future work aimed at determining the propensity of the RCT material to foam, and methods to remediate any foaming potential. According to DWPF themore » Tank Farm 2H evaporator has experienced foaming while processing DWPF recycle materials. The characterization work on the RCT samples has been completed and is reported here.« less

SLUDGE WASHING AND DEMONSTRATION OF THE DWPF FLOWSHEET IN THE SRNL SHIELDED CELLS FOR SLUDGE BATCH 7A QUALIFICATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J.; Billings, A.; Click, D.

2011-07-08

Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry (Sludge Batch 7a*) be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from H Canyon are oftenmore » added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). Sludge Batch 7a (SB7a) is composed of portions of Tanks 4, 7, and 12; the Sludge Batch 6 heel in Tank 51; and a plutonium stream from H Canyon. SRNL received the Tank 51 qualification sample (sample ID HTF-51-10-125) following sludge additions to Tank 51. This report documents: (1) The washing (addition of water to dilute the sludge supernate) and concentration (decanting of supernate) of the SB7a - Tank 51 qualification sample to adjust sodium content and weight percent insoluble solids to Tank Farm projections. (2) The performance of a DWPF Chemical Process Cell (CPC) simulation using the washed Tank 51 sample. The simulation included a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid was added to the sludge to destroy nitrite and reduce mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit was added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters were based on work with a non-radioactive simulant. (3) Vitrification of a portion of the SME product and characterization and durability testing (as measured by the Product Consistency Test (PCT)) of the resulting glass. (4) Rheology measurements of the initial slurry samples and samples after each phase of CPC processing. This program was controlled by a Task Technical and Quality Assurance Plan (TTQAP), and analyses were guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R&D) for the DWPF. It should be noted that much of the data in this document has been published in interoffice memoranda. The intent of this technical report is bring all of the SB7a related data together in a single permanent record and to discuss the overall aspects of SB7a processing.« less

Testing of the Defense Waste Processing Facility Cold Chemical Dissolution Method in Sludge Batch 9 Qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.; Pareizs, J.; Coleman, C.

For each sludge batch that is processed in the Defense Waste Processing Facility (DWPF), the Savannah River National Laboratory (SRNL) tests the applicability of the digestion methods used by the DWPF Laboratory for elemental analysis of Sludge Receipt and Adjustment Tank (SRAT) Receipt samples and SRAT Product process control samples. DWPF SRAT samples are typically dissolved using a method referred to as the DWPF Cold Chemical or Cold Chem Method (CC), (see DWPF Procedure SW4- 15.201). Testing indicates that the CC method produced mixed results. The CC method did not result in complete dissolution of either the SRAT Receipt ormore » SRAT Product with some fine, dark solids remaining. However, elemental analyses did not reveal extreme biases for the major elements in the sludge when compared with analyses obtained following dissolution by hot aqua regia (AR) or sodium peroxide fusion (PF) methods. The CC elemental analyses agreed with the AR and PF methods well enough that it should be adequate for routine process control analyses in the DWPF after much more extensive side-by-side tests of the CC method and the PF method are performed on the first 10 SRAT cycles of the Sludge Batch 9 (SB9) campaign. The DWPF Laboratory should continue with their plans for further tests of the CC method during these 10 SRAT cycles.« less

Impact of Salt Waste Processing Facility Streams on the Nitric-Glycolic Flowsheet in the Chemical Processing Cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, C.

An evaluation of the previous Chemical Processing Cell (CPC) testing was performed to determine whether the planned concurrent operation, or “coupled” operations, of the Defense Waste Processing Facility (DWPF) with the Salt Waste Processing Facility (SWPF) has been adequately covered. Tests with the nitricglycolic acid flowsheet, which were both coupled and uncoupled with salt waste streams, included several tests that required extended boiling times. This report provides the evaluation of previous testing and the testing recommendation requested by Savannah River Remediation. The focus of the evaluation was impact on flammability in CPC vessels (i.e., hydrogen generation rate, SWPF solvent components,more » antifoam degradation products) and processing impacts (i.e., acid window, melter feed target, rheological properties, antifoam requirements, and chemical composition).« less

VERIFICATION OF THE DEFENSE WASTE PROCESSING FACILITY PROCESS DIGESTION METHOD FOR THE SLUDGE BATCH 6 QUALIFICATION SAMPLE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Click, D.; Jones, M.; Edwards, T.

2010-06-09

For each sludge batch that is processed in the Defense Waste Processing Facility (DWPF), the Savannah River National Laboratory (SRNL) confirms applicability of the digestion method to be used by the DWPF lab for elemental analysis of Sludge Receipt and Adjustment Tank (SRAT) receipt samples and SRAT product process control samples.1 DWPF SRAT samples are typically dissolved using a room temperature HF-HNO3 acid dissolution (i.e., DWPF Cold Chem (CC) Method, see DWPF Procedure SW4-15.201) and then analyzed by inductively coupled plasma - atomic emission spectroscopy (ICPAES). In addition to the CC method confirmation, the DWPF lab's mercury (Hg) digestion methodmore » was also evaluated for applicability to SB6 (see DWPF procedure 'Mercury System Operating Manual', Manual: SW4-15.204. Section 6.1, Revision 5, Effective date: 12-04-03). This report contains the results and comparison of data generated from performing the Aqua Regia (AR), Sodium Peroxide/Hydroxide Fusion (PF) and DWPF Cold Chem (CC) method digestion of Sludge Batch 6 (SB6) SRAT Receipt and SB6 SRAT Product samples. For validation of the DWPF lab's Hg method, only SRAT receipt material was used and compared to AR digestion results. The SB6 SRAT Receipt and SB6 SRAT Product samples were prepared in the SRNL Shielded Cells, and the SRAT Receipt material is representative of the sludge that constitutes the SB6 Batch or qualification composition. This is the sludge in Tank 51 that is to be transferred into Tank 40, which will contain the heel of Sludge Batch 5 (SB5), to form the SB6 Blend composition. In addition to the 16 elements currently measured by the DWPF, this report includes Hg and thorium (Th) data (Th comprising {approx}2.5 - 3 Wt% of the total solids in SRAT Receipt and SRAT Product, respectively) and provides specific details of ICP-AES analysis of Th. Thorium was found to interfere with the U 367.007 nm emission line, and an inter-element correction (IEC) had to be applied to U data, which is also discussed. The results for any one particular element should not be used in any way to identify the form or speciation of a particular element without support from XRD analysis or used to estimate ratios of compounds in the sludge.« less

IMPACTS OF ANTIFOAM ADDITIONS AND ARGON BUBBLING ON DEFENSE WASTE PROCESSING FACILITY REDUCTION/OXIDATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C.; Johnson, F.

2012-06-05

During melting of HLW glass, the REDOX of the melt pool cannot be measured. Therefore, the Fe{sup +2}/{Sigma}Fe ratio in the glass poured from the melter must be related to melter feed organic and oxidant concentrations to ensure production of a high quality glass without impacting production rate (e.g., foaming) or melter life (e.g., metal formation and accumulation). A production facility such as the Defense Waste Processing Facility (DWPF) cannot wait until the melt or waste glass has been made to assess its acceptability, since by then no further changes to the glass composition and acceptability are possible. therefore, themore » acceptability decision is made on the upstream process, rather than on the downstream melt or glass product. That is, it is based on 'feed foward' statistical process control (SPC) rather than statistical quality control (SQC). In SPC, the feed composition to the melter is controlled prior to vitrification. Use of the DWPF REDOX model has controlled the balanjce of feed reductants and oxidants in the Sludge Receipt and Adjustment Tank (SRAT). Once the alkali/alkaline earth salts (both reduced and oxidized) are formed during reflux in the SRAT, the REDOX can only change if (1) additional reductants or oxidants are added to the SRAT, the Slurry Mix Evaporator (SME), or the Melter Feed Tank (MFT) or (2) if the melt pool is bubble dwith an oxidizing gas or sparging gas that imposes a different REDOX target than the chemical balance set during reflux in the SRAT.« less

DWPF DECON FRIT SUPERNATE ANALYSIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D.; Crawford, C.

2010-09-22

The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. This report contains the results of the supernate analyses, while the solids (sump and slurry) results will be reported in a supplemental report. The analytical data from the decon frit supernate indicate that all ofmore » the radionuclide, organic, and inorganic concentrations met the limits in Revision 4 of the Effluent Treatment Plant (ETP) Waste Acceptance Criteria (WAC) with the exception of boron. The ETP WAC limit for boron is 15.0 mg/L while the average measured concentration (based on quadruplicate analysis) was 15.5 mg/L. The measured concentrations of Li, Na, and Si were also relatively high in the supernate analysis. These results are consistent with the relatively high measured value of B given the compositional make-up of Frit 418. Given these results, it was speculated that either (a) Frit 418 was dissolving into the supernate or aqueous fraction and/or (b) fine frit particulates were carried forward to the analytical instrument based on the sampling procedure used (i.e., the supernate samples were not filtered - only settled with the liquid fraction being transferred with a pipette). To address this issue, a filtered supernate sample (using a 0.45 um filter) was prepared and submitted for analysis. The results of the filtered sample were consistent with 'unfiltered or settled' sample - relatively high values of B, Li, Na, and Si were found. This suggests that Frit 418 is dissolving in the liquid phase which could be enhanced by the high surface area of the frit fines or particulates in suspension. Based on the results of this study, it is recommended that DWPF re-evaluate the technical basis for the B WAC limit (the only component that exceeds the ETP WAC limit from the supernate analyses) or assess if a waiver or exception can be obtained for exceeding this limit. Given the possible dissolution of B, Li, Na, and Si into the supernate (due to dissolution of frit), DWPF may need to assess if the release of these frit components into the supernate are a concern for the disposal options being considered. It should be noted that the results of this study may not be representative of future decon frit solutions or sump/slurry solids samples. Therefore, future DWPF decisions regarding the possible disposal pathways for either the aqueous or solid portions of the Decon Frit system need to factor in the potential differences. More specifically, introduction of a different frit or changes to other DWPF flowsheet unit operations (e.g., different sludge batch or coupling with other process streams) may impact not only the results but also the conclusions regarding acceptability with respect to the ETF WAC limits.« less

2013 CEF RUN - PHASE 1 DATA ANALYSIS AND MODEL VALIDATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, A.

2014-05-08

Phase 1 of the 2013 Cold cap Evaluation Furnace (CEF) test was completed on June 3, 2013 after a 5-day round-the-clock feeding and pouring operation. The main goal of the test was to characterize the CEF off-gas produced from a nitric-formic acid flowsheet feed and confirm whether the CEF platform is capable of producing scalable off-gas data necessary for the revision of the DWPF melter off-gas flammability model; the revised model will be used to define new safety controls on the key operating parameters for the nitric-glycolic acid flowsheet feeds including total organic carbon (TOC). Whether the CEF off-gas datamore » were scalable for the purpose of predicting the potential flammability of the DWPF melter exhaust was determined by comparing the predicted H{sub 2} and CO concentrations using the current DWPF melter off-gas flammability model to those measured during Phase 1; data were deemed scalable if the calculated fractional conversions of TOC-to-H{sub 2} and TOC-to-CO at varying melter vapor space temperatures were found to trend and further bound the respective measured data with some margin of safety. Being scalable thus means that for a given feed chemistry the instantaneous flow rates of H{sub 2} and CO in the DWPF melter exhaust can be estimated with some degree of conservatism by multiplying those of the respective gases from a pilot-scale melter by the feed rate ratio. This report documents the results of the Phase 1 data analysis and the necessary calculations performed to determine the scalability of the CEF off-gas data. A total of six steady state runs were made during Phase 1 under non-bubbled conditions by varying the CEF vapor space temperature from near 700 to below 300°C, as measured in a thermowell (T{sub tw}). At each steady state temperature, the off-gas composition was monitored continuously for two hours using MS, GC, and FTIR in order to track mainly H{sub 2}, CO, CO{sub 2}, NO{sub x}, and organic gases such as CH{sub 4}. The standard deviation of the average vapor space temperature during each steady state ranged from 2 to 6°C; however, those of the measured off-gas data were much larger due to the inherent cold cap instabilities in the slurry-fed melters. In order to predict the off-gas composition at the sampling location downstream of the film cooler, the measured feed composition was charge-reconciled and input into the DWPF melter off-gas flammability model, which was then run under the conditions for each of the six Phase 1 steady states. In doing so, it was necessary to perform an overall heat/mass balance calculation from the melter to the Off-Gas Condensate Tank (OGCT) in order to estimate the rate of air inleakage as well as the true gas temperature in the CEF vapor space (T{sub gas}) during each steady state by taking into account the effects of thermal radiation on the measured temperature (T{sub tw}). The results of Phase 1 data analysis and subsequent model runs showed that the predicted concentrations of H{sub 2} and CO by the DWPF model correctly trended and further bounded the respective measured data in the CEF off-gas by over predicting the TOC-to-H{sub 2} and TOC-to-CO conversion ratios by a factor of 2 to 5; an exception was the 7X over prediction of the latter at T{sub gas} = 371°C but the impact of CO on the off-gas flammability potential is only minor compared to that of H{sub 2}. More importantly, the seemingly-excessive over prediction of the TOC-to-H{sub 2} conversion by a factor of 4 or higher at T{sub gas} < ~350°C was attributed to the conservative antifoam decomposition scheme added recently to the model and therefore is considered a modeling issue and not a design issue. At T{sub gas} > ~350°C, the predicted TOC-to-H{sub 2} conversions were closer to but still higher than the measured data by a factor of 2, which may be regarded as adequate from the safety margin standpoint. The heat/mass balance calculations also showed that the correlation between T{sub tw} and T{sub gas} in the CEF vapor space was close to that of the ½ scale SGM, whose data were taken as directly applicable to the DWPF melter and thus used to set all the parameters of the original model. Based on these results of the CEF Phase 1 off-gas and thermal data analyses, it is concluded that: (1) The thermal characteristics of the CEF vapor space are prototypic thanks to its prototypic design; and (2) The CEF off-gas data are scalable in terms of predicting the flammability potential of the DWPF melter off-gas. These results also show that the existing DWPF safety controls on the TOC and antifoam as a function of nitrate are conservative by the same order of magnitude shown by the Phase 1 data at T{sub gas} < ~350°C, since they were set at T{sub gas} = 294°C, which falls into the region of excessive conservatism for the current DWPF model in terms of predicting the TOC-to-H{sub 2} conversion. In order to remedy the overly-conservative antifoam decomposition scheme used in the current DWPF model, the data from two recent tests will be analyzed in detail in order to gain additional insights into the antifoam decomposition chemistry in the cold cap. The first test was run in a temperature-programmed furnace using both normal and spiked feeds with fresh antifoam under inert and slightly oxidizing vapor space conditions. Phase 2 of the CEF test was run with the baseline nitric-glycolic acid flowsheet feeds that contained the “processed antifoam” and those spiked with fresh antifoam in order to study the effects of antifoam concentration as well as processing history on its decomposition chemistry under actual melter conditions. The goal is to develop an improved antifoam decomposition model from the analysis of these test data and incorporate it into a new multistage cold cap model to be developed concurrently for the nitric-glycolic acid flowsheet feeds. These activities will be documented in the Phase 2 report. Finally, it is recommended that some of the conservatism in the existing DWPF safety controls be removed by improving the existing measured-vs.-true gas temperature correlation used in the melter vapor space combustion calculations. The basis for this recommendation comes from the fact that the existing correlation was developed by linearly extrapolating the SGM data taken over a relatively narrow temperature range down to the safety basis minimum of 460°C, thereby under predicting the true gas temperature considerably, as documented in this report. Specifically, the task of improving the current temperature correlation will involve; (1) performing a similar heat/mass balance analysis used in this study on actual DWPF data, (2) validating the measured-vs.-true gas temperature correlation for the CEF developed in this study against the DWPF melter heat/mass balance results, and (3) making adjustments to the CEF correlation, if necessary, before incorporating it into the DWPF safety basis calculations. The steps described here can be completed with relatively minimum efforts.« less

DEVELOPMENT OF REMOTE HANFORD CONNECTOR GASKET REPLACEMENT TOOLING FOR DWPF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krementz, D.; Coughlin, Jeffrey

2009-05-05

The Defense Waste Processing Facility (DWPF) requested the Savannah River National Laboratory (SRNL) to develop tooling and equipment to remotely replace gaskets in mechanical Hanford connectors to reduce personnel radiation exposure as compared to the current hands-on method. It is also expected that radiation levels will continually increase with future waste streams. The equipment is operated in the Remote Equipment Decontamination Cell (REDC), which is equipped with compressed air, two master-slave manipulators (MSM's) and an electro-mechanical manipulator (EMM) arm for operation of the remote tools. The REDC does not provide access to electrical power, so the equipment must be manuallymore » or pneumatically operated. The MSM's have a load limit at full extension of ten pounds, which limited the weight of the installation tool. In order to remotely replace Hanford connector gaskets several operations must be performed remotely, these include: removal of the spent gasket and retaining ring (retaining ring is also called snap ring), loading the new snap ring and gasket into the installation tool and installation of the new gasket into the Hanford connector. SRNL developed and tested tools that successfully perform all of the necessary tasks. Removal of snap rings from horizontal and vertical connectors is performed by separate air actuated retaining ring removal tools and is manipulated in the cell by the MSM. In order install a new gasket, the snap ring loader is used to load a new snap ring into a groove in the gasket installation tool. A new gasket is placed on the installation tool and retained by custom springs. An MSM lifts the installation tool and presses the mounted gasket against the connector block. Once the installation tool is in position, the gasket and snap ring are installed onto the connector by pneumatic actuation. All of the tools are located on a custom work table with a pneumatic valve station that directs compressed air to the desired tool and vents the tools as needed. Extensive testing of tooling operation was performed in the DWPF manipulator repair shop. This testing allowed the operators to gain confidence before the equipment was exposed to radioactive contamination. The testing also led to multiple design improvements. On July 17 and 29, 2008 the Remote Gasket Replacement Tooling was successfully demonstrated in the REDC at the DWPF of The Savannah River Site.« less

Nuclear Waste: Defense Waste Processing Facility-Cost, Schedule, and Technical Issues.

DTIC Science & Technology

1992-06-17

gallons of high-level radioactive waste stored in underground tanks at the savannah major facility involved Is the Defense Waste Processing Facility ( DwPF ...As a result of concerns about potential problems with the DWPF and delays in its scheduled start-up, the Chairman of the Environment, Energy, and...Natural Resources Subcommittee, House Committee on Government Operations, asked GAO to review the status of the DWPF and other facilities. This report

Comparative risk assessments for the production and interim storage of glass and ceramic waste forms: Defense waste processing facility

NASA Astrophysics Data System (ADS)

Huang, J. C.; Wright, W. V.

1982-04-01

The Defense Waste Processing Facility (DWPF) for immobilizing nuclear high level waste (HLW) is scheduled to be built. High level waste is produced when reactor components are subjected to chemical separation operations. Two candidates for immobilizing this HLW are borosilicate glass and crystalline ceramic, either being contained in weld sealed stainless steel canisters. A number of technical analyses are being conducted to support a selection between these two waste forms. The risks associated with the manufacture and interim storage of these two forms in the DWPF are compared. Process information used in the risk analysis was taken primarily from a DWPF processibility analysis. The DWPF environmental analysis provided much of the necessary environmental information.

Hydrogen Production in Radioactive Solutions in the Defense Waste Processing Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

CRAWFORD, CHARLES L.

2004-05-26

In the radioactive slurries and solutions to be processed in the Defense Waste Processing Facility (DWPF), hydrogen will be produced continuously by radiolysis. This production results from alpha, beta, and gamma rays from decay of radionuclides in the slurries and solutions interacting with the water. More than 1000 research reports have published data concerning this radiolytic production. The results of these studies have been reviewed in a comprehensive monograph. Information about radiolytic hydrogen production from the different process tanks is necessary to determine air purge rates necessary to prevent flammable mixtures from accumulating in the vapor spaces above these tanks.more » Radiolytic hydrogen production rates are usually presented in terms of G values or molecules of hydrogen produced per 100ev of radioactive decay energy absorbed by the slurry or solution. With the G value for hydrogen production, G(H2), for a particular slurry and the concentrations of radioactive species in that slurry, the rate of H2 production for that slurry can be calculated. An earlier investigation estimated that the maximum rate that hydrogen could be produced from the sludge slurry stream to the DWPF is with a G value of 0.45 molecules per 100ev of radioactive decay energy sorbed by the slurry.« less

Infrasound Detection of Rocket Launches

DTIC Science & Technology

2000-09-01

infrasound pressure, and λ and µ are the Lame and shear modulii. Seismic data was available from the IRIS data center for the seismic station DWPF ...the bandwidth of interest. Figure 4 shows a recording of STS-93 (07/24/99 04:31:00GMT) at DWPF (97 km). The largest seismic amplitudes are consistent...lasts ~400 seconds. The dominant frequency (~4 Hz) at DWPF is consistent with the long-range infrasound signals observed at DLIAR. Figure 3. Seismic

SLUDGE BATCH 6/TANK 40 SIMULANT CHEMICAL PROCESS CELL SIMULATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, David

2010-04-28

Phase III simulant flowsheet testing was completed using the latest composition estimates for SB6/Tank 40 feed to DWPF. The goals of the testing were to determine reasonable operating conditions and assumptions for the startup of SB6 processing in the DWPF. Testing covered the region from 102-159% of the current DWPF stoichiometric acid equation. Nitrite ion concentration was reduced to 90 mg/kg in the SRAT product of the lowest acid run. The 159% acid run reached 60% of the DWPF Sludge Receipt and Adjustment Tank (SRAT) limit of 0.65 lb H2/hr, and then sporadically exceeded the DWPF Slurry Mix Evaporator (SME)more » limit of 0.223 lb H2/hr. Hydrogen generation rates peaked at 112% of the SME limit, but higher than targeted wt% total solids levels may have been partially responsible for rates seen. A stoichiometric factor of 120% met both objectives. A processing window for SB6 exists from 102% to something close to 159% based on the simulant results. An initial recommendation for SB6 processing is at 115-120% of the current DWPF stoichiometric acid equation. The addition of simulated Actinide Removal Process (ARP) and Modular Caustic Side Solvent Extraction Unit (MCU) streams to the SRAT cycle had no apparent impact on the preferred stoichiometric factor. Hydrogen generation occurred continuously after acid addition in three of the four tests. The three runs at 120%, 118.4% with ARP/MCU, and 159% stoichiometry were all still producing around 0.1 lb hydrogen/hr at DWPF scale after 36 hours of boiling in the SRAT. The 120% acid run reached 23% of the SRAT limit and 37% of the SME limit. Conversely, nitrous oxide generation was subdued compared to previous sludge batches, staying below 29 lb/hr in all four tests or about a fourth as much as in comparable SB4 testing. Two processing issues, identified during SB6 Phase II flowsheet testing and qualification simulant testing, were monitored during Phase III. Mercury material balance closure was impacted by acid stoichiometry, and significant mercury was not accounted for in the highest acid run. Coalescence of elemental mercury droplets in the mercury water wash tank (MWWT) appeared to degrade with increasing stoichiometry. Observations were made of mercury scale formation in the SRAT condenser and MWWT. A tacky mercury amalgam with Rh, Pd, and Cu, plus some Ru and Ca formed on the impeller at 159% acid. It contained a significant fraction of the available Pd, Cu, and Rh as well as about 25% of the total mercury charged. Free (elemental) mercury was found in all of the SME products. Ammonia scrubbers were used during the tests to capture off-gas ammonia for material balance purposes. Significant ammonium ion formation was again observed during the SRAT cycle, and ammonia gas entered the off-gas as the pH rose during boiling. Ammonium ion production was lower than in the SB6 Phase II and the qualification simulant testing. Similar ammonium ion formation was seen in the ARP/MCU simulation as in the 120% flowsheet run. A slightly higher pH caused most of the ammonium to vaporize and collect in the ammonia scrubber reflux solution. Two periods of foaminess were noted. Neither required additional antifoam to control the foam growth. A steady foam layer formed during reflux in the 120% acid run. It was about an inch thick, but was 2-3 times more volume of bubbles than is typically seen during reflux. A similar foam layer also was seen during caustic boiling of the simulant during the ARP addition. While frequently seen with the radioactive sludge, foaminess during caustic boiling with simulants has been relatively rare. Two further flowsheet tests were performed and will be documented separately. One test was to evaluate the impact of process conditions that match current DWPF operation (lower rates). The second test was to evaluate the impact of SRAT/SME processing on the rheology of a modified Phase III simulant that had been made five times more viscous using ultrasonication.« less

DWPF simulant CPC studies for SB8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, D. C.; Zamecnik, J. R.

2013-06-25

The Savannah River National Laboratory (SRNL) accepted a technical task request (TTR) from Waste Solidification Engineering to perform simulant tests to support the qualification of Sludge Batch 8 (SB8) and to develop the flowsheet for SB8 in the Defense Waste Processing Facility (DWPF). These efforts pertained to the DWPF Chemical Process Cell (CPC). Separate studies were conducted for frit development and glass properties (including REDOX). The SRNL CPC effort had two primary phases divided by the decision to drop Tank 12 from the SB8 constituents. This report focuses on the second phase with SB8 compositions that do not contain themore » Tank 12 piece. A separate report will document the initial phase of SB8 testing that included Tank 12. The second phase of SB8 studies consisted of two sets of CPC studies. The first study involved CPC testing of an SB8 simulant for Tank 51 to support the CPC demonstration of the washed Tank 51 qualification sample in the SRNL Shielded Cells facility. SB8-Tank 51 was a high iron-low aluminum waste with fairly high mercury and moderate noble metal concentrations. Tank 51 was ultimately washed to about 1.5 M sodium which is the highest wash endpoint since SB3-Tank 51. This study included three simulations of the DWPF Sludge Receipt and Adjustment Tank (SRAT) cycle and Slurry Mix Evaporator (SME) cycle with the sludge-only flowsheet at nominal DWPF processing conditions and three different acid stoichiometries. These runs produced a set of recommendations that were used to guide the successful SRNL qualification SRAT/SME demonstration with actual Tank 51 washed waste. The second study involved five SRAT/SME runs with SB8-Tank 40 simulant. Four of the runs were designed to define the acid requirements for sludge-only processing in DWPF with respect to nitrite destruction and hydrogen generation. The fifth run was an intermediate acid stoichiometry demonstration of the coupled flowsheet for SB8. These runs produced a set of processing recommendations for DWPF along with some data related to Safety Class documentation at DWPF. Some significant observations regarding SB8 follow: Reduced washing in Tank 51 led to an increase in the wt.% soluble solids of the DWPF feed. If wt.% total solids for the SRAT and SME product weren’t adjusted upward to maintain insoluble solids levels similar to past sludge batches, then the rheological properties of the slurry went below the low end of the DWPF design bases for the SRAT and SME. Much higher levels of dissolved manganese were found in the SRAT and SME products than in recent sludge batches. Closed crucible melts were more reduced than expected. The working hypothesis is that the soluble Mn is less oxidizing than assumed in the REDOX calculations. A change in the coefficient for Mn in the REDOX equation was recommended in a separate report. The DWPF (Hsu) stoichiometric acid equation was examined in detail to better evaluate how to control acid in DWPF. The existing DWPF equation can likely be improved without changing the required sample analyses through a paper study using existing data. The recommended acid stoichiometry for initial SB8 SRAT batches is 115-120% stoichiometry until some processing experience is gained. The conservative range (based on feed properties) of stoichiometric factors derived in this study was from 110-147%, but SRNL recommends using only the lower half of this range, 110-126% even after initial batches provide processing experience. The stoichiometric range for sludge-only processing appears to be suitable for coupled operation based on results from the run in the middle of the range. Catalytic hydrogen was detectable (>0.005 vol%) in all SRAT and SME cycles. Hydrogen reached 30-35% of the SRAT and SME limits at the mid-point of the stoichiometry window (bounding noble metals and acid demand).« less

Literature review: Assessment of DWPF melter and melter off-gas system lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M. M.

2015-07-30

A glass melter for use in processing radioactive waste is a challenging environment for the materials of construction (MOC) resulting from a combination of high temperatures, chemical attack, and erosion/corrosion; therefore, highly engineered materials must be selected for this application. The focus of this report is to review the testing and evaluations used in the selection of the Defense Waste Processing Facility (DWPF), glass contact MOC specifically the Monofrax ® K-3 refractory and Inconel ® 690 alloy. The degradation or corrosion mechanisms of these materials during pilot scale testing and in-service operation were analyzed over a range of oxidizing andmore » reducing flowsheets; however, DWPF has primarily processed a reducing flowsheet (i.e., Fe 2+/ΣFe of 0.09 to 0.33) since the start of radioactive operations. This report also discusses the materials selection for the DWPF off-gas system and the corrosion evaluation of these materials during pilot scale testing and non-radioactive operations of DWPF Melter #1. Inspection of the off-gas components has not been performed during radioactive operations with the exception of maintenance because of plugging.« less

Literature review: Assessment of DWPF melter and melter off-gas system lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M.

2015-07-30

A glass melter for use in processing radioactive waste is a challenging environment for the materials of construction (MOC) resulting from a combination of high temperatures, chemical attack, and erosion/corrosion; therefore, highly engineered materials must be selected for this application. The focus of this report is to review the testing and evaluations used in the selection of the Defense Waste Processing Facility (DWPF), glass contact MOC specifically the Monofrax® K-3 refractory and Inconel® 690 alloy. The degradation or corrosion mechanisms of these materials during pilot scale testing and in-service operation were analyzed over a range of oxidizing and reducing flowsheets;more » however, DWPF has primarily processed a reducing flowsheet (i.e., Fe 2+/ΣFe of 0.09 to 0.33) since the start of radioactive operations. This report also discusses the materials selection for the DWPF off-gas system and the corrosion evaluation of these materials during pilot scale testing and non-radioactive operations of DWPF Melter #1. Inspection of the off-gas components has not been performed during radioactive operations with the exception of maintenance because of plugging.« less

Sludge Washing and Demonstration of the DWPF Nitric/Formic Flowsheet in the SRNL Shielded Cells for Sludge Batch 9 Qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J.; Newell, D.; Martino, C.

Savannah River National Laboratory (SRNL) was requested by Savannah River Remediation (SRR) to qualify the next batch of sludge – Sludge Batch 9 (SB9). Current practice is to prepare sludge batches in Tank 51 by transferring sludge to Tank 51 from other tanks. The sludge is washed and transferred to Tank 40, the current Defense Waste Process Facility (DWPF) feed tank. Prior to sludge transfer from Tank 51 to Tank 40, the Tank 51 sludge must be qualified. SRNL qualifies the sludge in multiple steps. First, a Tank 51 sample is received, then characterized, washed, and again characterized. SRNL thenmore » demonstrates the DWPF Chemical Process Cell (CPC) flowsheet with the sludge. The final step of qualification involves chemical durability measurements of glass fabricated in the DWPF CPC demonstrations. In past sludge batches, SRNL had completed the DWPF demonstration with Tank 51 sludge. For SB9, SRNL has been requested to process a blend of Tank 51 and Tank 40 at a targeted ratio of 44% Tank 51 and 56% Tank 40 on an insoluble solids basis.« less

Mercury Reduction and Removal from High Level Waste at the Defense Waste Processing Facility - 12511

DOE Office of Scientific and Technical Information (OSTI.GOV)

Behrouzi, Aria; Zamecnik, Jack

2012-07-01

The Defense Waste Processing Facility processes legacy nuclear waste generated at the Savannah River Site during production of enriched uranium and plutonium required by the Cold War. The nuclear waste is first treated via a complex sequence of controlled chemical reactions and then vitrified into a borosilicate glass form and poured into stainless steel canisters. Converting the nuclear waste into borosilicate glass is a safe, effective way to reduce the volume of the waste and stabilize the radionuclides. One of the constituents in the nuclear waste is mercury, which is present because it served as a catalyst in the dissolutionmore » of uranium-aluminum alloy fuel rods. At high temperatures mercury is corrosive to off-gas equipment, this poses a major challenge to the overall vitrification process in separating mercury from the waste stream prior to feeding the high temperature melter. Mercury is currently removed during the chemical process via formic acid reduction followed by steam stripping, which allows elemental mercury to be evaporated with the water vapor generated during boiling. The vapors are then condensed and sent to a hold tank where mercury coalesces and is recovered in the tank's sump via gravity settling. Next, mercury is transferred from the tank sump to a purification cell where it is washed with water and nitric acid and removed from the facility. Throughout the chemical processing cell, compounds of mercury exist in the sludge, condensate, and off-gas; all of which present unique challenges. Mercury removal from sludge waste being fed to the DWPF melter is required to avoid exhausting it to the environment or any negative impacts to the Melter Off-Gas system. The mercury concentration must be reduced to a level of 0.8 wt% or less before being introduced to the melter. Even though this is being successfully accomplished, the material balances accounting for incoming and collected mercury are not equal. In addition, mercury has not been effectively purified and collected in the Mercury Purification Cell (MPC) since 2008. A significant cleaning campaign aims to bring the MPC back up to facility housekeeping standards. Two significant investigations are being undertaken to restore mercury collection. The SMECT mercury pump has been removed from the tank and will be functionally tested. Also, research is being conducted by the Savannah River National Laboratory to determine the effects of antifoam addition on the behavior of mercury. These path forward items will help us better understand what is occurring in the mercury collection system and ultimately lead to an improved DWPF production rate and mercury recovery rate. (authors)« less

The Impact Of The MCU Life Extension Solvent On Sludge Batch 8 Projected Operating Windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D. K.; Edwards, T. B.

2013-06-26

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NGS) and a new strip acid will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing or evaluations with the next generation solvent are required to determine the impact of these changes (if any) to Chemical Process Cell (CPC) activities, glass formulation strategies, and melter operations at the Defense Waste Processing Facility (DWPF). The introduction of the dilute (0.01 M) boric acid streammore » into the DWPF flowsheet has a potential impact on glass formulation and frit development efforts since B203 is a major oxide in frits developed for DWPF. Prior knowledge of this stream can be accounted for during frit development efforts but that was not the case for Sludge Batch 8 (SB8). Frit 803 has already been recommended and procured for SB8 processing; altering the frit to account for the incoming boron from the strip effluent (SE) is not an option for SB8. Therefore, the operational robustness of Frit 803 to the introduction of SE including its compositional tolerances (i.e., up to 0.0125M boric acid) is of interest and was the focus of this study. The primary question to be addressed in the current study was: What is the impact (if any) on the projected operating windows for the Frit 803 - SB8 flowsheet to additions of B203 from the SE in the Sludge Receipt and Adjustment Tank (SRAT)? More specifically, will Frit 803 be robust to the potential compositional changes occurring in the SRAT due to sludge variation, varying additions of ARP and/or the introduction of SE by providing access to waste loadings (WLs) of interest to DWPF? The Measurement Acceptability Region (MAR) results indicate there is very little, if any, impact on the projected operating windows for the Frit 803 - SB8 system regardless of the presence or absence of ARP and SE (up to 2 wt% B203 contained in the SRAT and up to 2000 gallons of ARP). It should be noted that 0.95 wt% B203 is the nominal projected concentration in the SRAT based on a 0.0125M boric acid flowsheet with 70,000 liters of SE being added to the SRAT.« less

The Impact Of The MCU Life Extension Solvent On Sludge Batch 8 Projected Operating Windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D. K.; Edwards, T. B.; Stone, M. E.

2013-08-14

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NGS) and a new strip acid will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing or evaluations with the next generation solvent are required to determine the impact of these changes (if any) to Chemical Process Cell (CPC) activities, glass formulation strategies, and melter operations at the Defense Waste Processing Facility (DWPF). The introduction of the dilute (0.01M) boric acid stream intomore » the DWPF flowsheet has a potential impact on glass formulation and frit development efforts since B2O3 is a major oxide in frits developed for DWPF. Prior knowledge of this stream can be accounted for during frit development efforts but that was not the case for Sludge Batch 8 (SB8). Frit 803 has already been recommended and procured for SB8 processing; altering the frit to account for the incoming boron from the strip effluent (SE) is not an option for SB8. Therefore, the operational robustness of Frit 803 to the introduction of SE including its compositional tolerances (i.e., up to 0.0125M boric acid) is of interest and was the focus of this study. The primary question to be addressed in the current study was: What is the impact (if any) on the projected operating windows for the Frit 803 – SB8 flowsheet to additions of B2O3 from the SE in the Sludge Receipt and Adjustment Tank (SRAT)? More specifically, will Frit 803 be robust to the potential compositional changes occurring in the SRAT due to sludge variation, varying additions of ARP and/or the introduction of SE by providing access to waste loadings (WLs) of interest to DWPF? The Measurement Acceptability Region (MAR) results indicate there is very little, if any, impact on the projected operating windows for the Frit 803 – SB8 system regardless of the presence or absence of ARP and SE (up to 2 wt% B2O3 contained in the SRAT and up to 2000 gallons of ARP). It should be noted that 0.95 wt% B2O3 is the nominal projected concentration in the SRAT based on a 0.0125M boric acid flowsheet with 70,000 liters of SE being added to the SRAT. The impact on CPC processing of a 0.01M boric acid solution for elution of cesium during Modular Caustic Side Solvent Extraction Unit (MCU) processing has previously been evaluated by the Savannah River National Laboratory (SRNL). Increasing the acid strength to 0.0125M boric acid to account for variations in the boric acid strength has been reviewed versus the previous evaluation. The amount of acid from the boric acid represented approximately 5% of the total acid during the previous evaluation. An increase from 0.01 to 0.0125M boric acid represents a change of approximately 1.3% which is well within the error of the acid calculation. Therefore, no significant changes to CPC processing (hydrogen generation, metal solubilities, rheological properties, REDOX control, etc.) are expected from an increase in allowable boric acid concentration from 0.01M to 0.0125M.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raszewski, F; Tommy Edwards, T; David Peeler, D

Sludge Batch 4 (SB4) is currently being processed in the Defense Waste Processing Facility (DWPF) using Frit 510. The slurry pumps in Tank 40 are experiencing in-leakage of bearing water, which is causing the sludge slurry in Tank 40 to become dilute at a rapid rate. Currently, the DWPF is removing this dilution water by performing caustic boiling during the Sludge Receipt and Adjustment Tank (SRAT) cycle. In order to alleviate prolonged SRAT cycle times, which may eventually impact canister production rates, the Liquid Waste Organization (LWO) performed a 100K gallon supernate decant of Tank 40 in April 2008. SRNLmore » performed a supplemental glass variability study to support the April 2008 100K gallon decant incorporating the impact of coupled operations (addition of the Actinide Removal Process (ARP) stream). Recently LWO requested that SRNL assess the impact of a second decant (up to 100K gallon) to the Frit 510-SB4 system. This second decant occurred in June 2008. LWO provided nominal compositions on May 6, 2008 representing Tank 40 prior to the second decant, following the second decant, and the SB4 Heel prior to blending with Tank 51 to constitute SB5. Paper study assessments were performed for these options based on sludge-only and coupled operations processing (ARP addition), as well as possible Na{sub 2}O additions (via NaOH additions) to both flowsheets. A review of the ComProTM database relative to the compositional region defined by the projections after the second decant coupled with Frit 510 identified only a few glasses with similar glass compositions. These glasses were acceptable from a durability perspective, but did not sufficiently cover the new glass compositional region. Therefore, SRNL recommended that a supplemental variability study be performed to support the June 2008 Tank 40 decant. Glasses were selected for the variability study based on three sludge compositional projections (sludge-only, coupled and coupled + 2 wt% Na{sub 2}O) at waste loadings (WLs) of interest to DWPF (32%, 35% and 38%). These nine glasses were fabricated and characterized using chemical composition analysis, X-ray Diffraction (XRD) and the Product Consistency Test (PCT). All of the glasses that were selected for this study satisfy the Product Composition Control System (PCCS) criteria and are deemed processable and acceptable for the DWPF, except for the SB4VS2-03 (sludge-only at 38% WL) target composition. This glass fails the T{sub L} criterion and would not be considered processable based on Slurry Mix Evaporator (SME) acceptability decisions. The durabilities of all of the study glasses (both quenched and ccc) are well below that of the normalized leachate for boron (NL [B]) of the reference EA glass (16.695 g/L) and are predictable using the current PCCS models. Very little variation exists between the NL [B] of the quenched and ccc versions of the glasses. There is some evidence of a trend toward a less durable glass as WL increases for some of the sludge projections. Frit 510 is a viable option for the processing of SB4 after a second Tank 40 decant with or without the addition of products from the ARP stream as well as the 2 wt% Na{sub 2}O addition. The addition of ARP had no negative impacts on the acceptability and predictability of the variability study glasses.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prod'homme, A.; Drouvot, O.; Gregory, J.

In 2009, Savannah River Remediation LLC (SRR) assumed the management lead of the Liquid Waste (LW) Program at the Savannah River Site (SRS). The four SRR partners and AREVA, as an integrated subcontractor are performing the ongoing effort to safely and reliably: - Close High Level Waste (HLW) storage tanks; - Maximize waste throughput at the Defense Waste Processing Facility (DWPF); - Process salt waste into stable final waste form; - Manage the HLW liquid waste material stored at SRS. As part of these initiatives, SRR and AREVA deployed a performance management methodology based on Overall Equipment Effectiveness (OEE) atmore » the DWPF in order to support the required production increase. This project took advantage of lessons learned by AREVA through the deployment of Total Productive Maintenance and Visual Management methodologies at the La Hague reprocessing facility in France. The project also took advantage of measurement data collected from different steps of the DWPF process by the SRR team (Melter Engineering, Chemical Process Engineering, Laboratory Operations, Plant Operations). Today the SRR team has a standard method for measuring processing time throughout the facility, a reliable source of objective data for use in decision-making at all levels, and a better balance between engineering department goals and operational goals. Preliminary results show that the deployment of this performance management methodology to the LW program at SRS has already significantly contributed to the DWPF throughput increases and is being deployed in the Saltstone facility. As part of the liquid waste program on Savannah River Site, SRR committed to enhance production throughput of DWPF. Beyond technical modifications implemented at different location of the facility, SRR deployed performance management methodology based on OEE metrics. The implementation benefited from the experience gained by AREVA in its own facilities in France. OEE proved to be a valuable tool in order to support the enhancement program in DWPF by providing unified metrics to measure plant performances, identify bottleneck location, and rank the most time consuming causes from objective data shared between the different groups belonging to the organization. Beyond OEE, the Visual Management tool adapted from the one used at La Hague were also provided in order to further enhance communication within the operating teams. As a result of all the initiatives implemented on DWPF, achieved production has been increased to record rates from FY10 to FY11. It is expected that thanks to the performance management tools now available within DWPF, these results will be sustained and even improved in the future to meet system plan targets. (authors)« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D; Tommy Edwards, T; Kevin Fox, K

The Savannah River National Laboratory (SRNL) has developed, and continues to enhance, its integrated capability to evaluate the impact of proposed sludge preparation plans on the Defense Waste Processing Facility's (DWPF's) operation. One of the components of this integrated capability focuses on frit development which identifies a viable frit or frits for each sludge option being contemplated for DWPF processing. A frit is considered viable if its composition allows for economic fabrication and if, when it is combined with the sludge option under consideration, the DWPF property/composition models (the models of DWPF's Product Composition Control System (PCCS)) indicate that themore » combination has the potential for an operating window (a waste loading (WL) interval over which the sludge/frit glass system satisfies processability and durability constraints) that would allow DWPF to meet its goals for waste loading and canister production. This report documents the results of SRNL's efforts to identify candidate frit compositions and corresponding predicted operating windows (defined in terms of WL intervals) for the February 2007 compositional projection of Sludge Batch 4 (SB4) developed by the Liquid Waste Organization (LWO). The nominal compositional projection was used to assess projected operating windows (in terms of a waste loading interval over which all predicted properties were classified as acceptable) for various frits, evaluate the applicability of the 0.6 wt% SO{sub 4}{sup =} PCCS limit to the glass systems of interest, and determine the impact (or lack thereof) to the previous SB4 variability studies. It should be mentioned that the information from this report will be coupled with assessments of melt rate to recommend a frit for SB4 processing. The results of this paper study suggest that candidate frits are available to process the nominal SB4 composition over attractive waste loadings of interest to DWPF. Specifically, two primary candidate frits for SB4 processing, Frit 510 and Frit 418, have projected operating windows that should allow for successful processing at DWPF. While Frit 418 has been utilized at DWPF, Frit 510 is a higher B{sub 2}O{sub 3} based frit which could lead to improvements in melt rate. These frits provide relatively large operating windows and demonstrate robustness to possible sludge compositional variation while avoiding potential nepheline formation issues. In addition, assessments of SO{sub 4}{sup =} solubility indicate that the 0.6 wt% SO{sub 4}{sup =} limit in PCCS is applicable for the Frit 418 and the Frit 510 based SB4 glass systems.« less

Urban Fire Simulation. Version 2

DTIC Science & Technology

1993-02-01

of the building. In this case the distribution of windows in the tract per floor ( DWPF (FLOORHT)) is calculated under the assumption that the number of...given urban area. The probability that no room on the subject floor will flash over is calculated at label (V) from PNRFOF DWPF (FLOORHT) (1 - FFORF

LITERATURE REVIEW ON IMPACT OF GLYCOLATE ON THE 2H EVAPORATOR AND THE EFFLUENT TREATMENT FACILITY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adu-Wusu, K.

2012-05-10

Glycolic acid (GA) is being studied as an alternate reductant in the Defense Waste Processing Facility (DWPF) feed preparation process. It will either be a total or partial replacement for the formic acid that is currently used. A literature review has been conducted on the impact of glycolate on two post-DWPF downstream systems - the 2H Evaporator system and the Effluent Treatment Facility (ETF). The DWPF recycle stream serves as a portion of the feed to the 2H Evaporator. Glycolate enters the evaporator system from the glycolate in the recycle stream. The overhead (i.e., condensed phase) from the 2H Evaporatormore » serves as a portion of the feed to the ETF. The literature search revealed that virtually no impact is anticipated for the 2H Evaporator. Glycolate may help reduce scale formation in the evaporator due to its high complexing ability. The drawback of the solubilizing ability is the potential impact on the criticality analysis of the 2H Evaporator system. It is recommended that at least a theoretical evaluation to confirm the finding that no self-propagating violent reactions with nitrate/nitrites will occur should be performed. Similarly, identification of sources of ignition relevant to glycolate and/or update of the composite flammability analysis to reflect the effects from the glycolate additions for the 2H Evaporator system are in order. An evaluation of the 2H Evaporator criticality analysis is also needed. A determination of the amount or fraction of the glycolate in the evaporator overhead is critical to more accurately assess its impact on the ETF. Hence, use of predictive models like OLI Environmental Simulation Package Software (OLI/ESP) and/or testing are recommended for the determination of the glycolate concentration in the overhead. The impact on the ETF depends on the concentration of glycolate in the ETF feed. The impact is classified as minor for feed glycolate concentrations {le} 33 mg/L or 0.44 mM. The ETF unit operations that will have minor/major impacts are chlorination, pH adjustment, 1st mercury removal, organics removal, 2nd mercury removal, and ion exchange. For minor impacts, the general approach is to use historical process operations data/modeling software like OLI/ESP and/or monitoring/compiled process operations data to resolve any uncertainties with testing as a last resort. For major impacts (i.e., glycolate concentrations > 33 mg/L or 0.44 mM), testing is recommended. No impact is envisaged for the following ETF unit operations regardless of the glycolate concentration - filtration, reverse osmosis, ion exchange resin regeneration, and evaporation.« less

Assessment of the impact of TOA partitioning on DWPF off-gas flammability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, W. E.

2013-06-01

An assessment has been made to evaluate the impact on the DWPF melter off-gas flammability of increasing the amount of TOA in the current solvent used in the Modular Caustic-Side Solvent Extraction Process Unit (MCU) process. The results of this study showed that the concentrations of nonvolatile carbon of the current solvent limit (150 ppm) in the Slurry Mix Evaporator (SME) product would be about 7% higher and the nonvolatile hydrogen would be 2% higher than the actual current solvent (126 ppm) with an addition of up to 3 ppm of TOA when the concentration of Isopar L in themore » effluent transfer is controlled below 87 ppm and the volume of MCU effluent transfer to DWPF is limited to 15,000 gallons per Sludge Receipt and Adjustment Tank (SRAT)/SME cycle. Therefore, the DWPF melter off-gas flammability assessment is conservative for up to an additional 3 ppm of TOA in the effluent based on these assumptions. This report documents the calculations performed to reach this conclusion.« less

Simulated Waste Testing Of Glycolate Impacts On The 2H-Evaporator System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, C. J.

2013-08-13

Glycolic acid is being studied as a total or partial replacement for formic acid in the Defense Waste Processing Facility (DWPF) feed preparation process. After implementation, the recycle stream from DWPF back to the high-level waste tank farm will contain soluble sodium glycolate. Most of the potential impacts of glycolate in the tank farm were addressed via a literature review, but several outstanding issues remained. This report documents the non-radioactive simulant tests impacts of glycolate on storage and evaporation of Savannah River Site high-level waste. The testing for which non-radioactive simulants could be used involved the following: the partitioning ofmore » glycolate into the evaporator condensate, the impacts of glycolate on metal solubility, and the impacts of glycolate on the formation and dissolution of sodium aluminosilicate scale within the evaporator. The following are among the conclusions from this work: Evaporator condensate did not contain appreciable amounts of glycolate anion. Of all tests, the highest glycolate concentration in the evaporator condensate was 0.38 mg/L. A significant portion of the tests had glycolate concentration in the condensate at less than the limit of quantification (0.1 mg/L). At ambient conditions, evaporator testing did not show significant effects of glycolate on the soluble components in the evaporator concentrates. Testing with sodalite solids and silicon containing solutions did not show significant effects of glycolate on sodium aluminosilicate formation or dissolution.« less

Characterization of DWPF recycle condensate tank materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.

2015-01-01

A Defense Waste Processing Facility (DWPF) Recycle Condensate Tank (RCT) sample was delivered to the Savannah River National Laboratory (SRNL) for characterization with particular interest in the concentration of I-129, U-233, U-235, total U, and total Pu. Since a portion of Salt Batch 8 will contain DWPF recycle materials, the concentration of I-129 is important to undertand for salt batch planning purposes. The chemical and physical characterizations are also needed as input to the interpretation of future work aimed at determining the propensity of the RCT material to foam, and methods to remediate any foaming potential. According to DWPF themore » Tank Farm 2H evaporator has experienced foaming while processing DWPF recycle materials. The characterization work on the RCT samples has been completed and is reported here. The composition of the Sludge Batch 8 (SB8) RCT material is largely a low base solution of 0.2M NaNO 2 and 0.1M NaNO 3 with a small amount of formate present. Insoluble solids comprise only 0.05 wt.% of the slurry. The solids appear to be largely sludge-like solids based on elemental composition and SEM-EDS analysis. The sample contains an elevated concentration of I-129 (38x) and substantial 59% fraction of Tc-99, as compared to the incoming SB8 Tank 40 feed material. The Hg concentration is 5x, when compared to Fe, of that expected based on sludge carryover. The total U and Pu concentrations are reduced significantly, 0.536 wt.% TS and 2.42E-03 wt.% TS, respectively, with the fissile components, U-233, U-235, Pu-239, and Pu-241, an order of magnitude lower in concentration than those in the SB8 Tank 40 DWPF feed material. This report will be revised to include the foaming study requested in the TTR and outlined in the TTQAP when that work is concluded.« less

DWPF Simulant CPC Studies For SB8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newell, J. D.

2013-09-25

Prior to processing a Sludge Batch (SB) in the Defense Waste Processing Facility (DWPF), flowsheet studies using simulants are performed. Typically, the flowsheet studies are conducted based on projected composition(s). The results from the flowsheet testing are used to 1) guide decisions during sludge batch preparation, 2) serve as a preliminary evaluation of potential processing issues, and 3) provide a basis to support the Shielded Cells qualification runs performed at the Savannah River National Laboratory (SRNL). SB8 was initially projected to be a combination of the Tank 40 heel (Sludge Batch 7b), Tank 13, Tank 12, and the Tank 51more » heel. In order to accelerate preparation of SB8, the decision was made to delay the oxalate-rich material from Tank 12 to a future sludge batch. SB8 simulant studies without Tank 12 were reported in a separate report.1 The data presented in this report will be useful when processing future sludge batches containing Tank 12. The wash endpoint target for SB8 was set at a significantly higher sodium concentration to allow acceptable glass compositions at the targeted waste loading. Four non-coupled tests were conducted using simulant representing Tank 40 at 110-146% of the Koopman Minimum Acid requirement. Hydrogen was generated during high acid stoichiometry (146% acid) SRAT testing up to 31% of the DWPF hydrogen limit. SME hydrogen generation reached 48% of of the DWPF limit for the high acid run. Two non-coupled tests were conducted using simulant representing Tank 51 at 110-146% of the Koopman Minimum Acid requirement. Hydrogen was generated during high acid stoichiometry SRAT testing up to 16% of the DWPF limit. SME hydrogen generation reached 49% of the DWPF limit for hydrogen in the SME for the high acid run. Simulant processing was successful using previously established antifoam addition strategy. Foaming during formic acid addition was not observed in any of the runs. Nitrite was destroyed in all runs and no N2O was detected during SME processing. Mercury behavior was consistent with that seen in previous SRAT runs. Mercury was stripped below the DWPF limit on 0.8 wt% for all runs. Rheology yield stress fell within or below the design basis of 1-5 Pa. The low acid Tank 40 run (106% acid stoichiometry) had the highest yield stress at 3.78 Pa.« less

DWPF Safely Dispositioning Liquid Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-01-05

The only operating radioactive waste glassification plant in the nation, the Defense Waste Processing Facility (DWPF) converts the liquid radioactive waste currently stored at the Savannah River Site (SRS) into a solid glass form suitable for long-term storage and disposal. Scientists have long considered this glassification process, called “vitrification,” as the preferred option for treating liquid radioactive waste.

Phase Stability Determinations of DWPF Waste Glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marra, S.L.

1999-10-22

Liquid high-level nuclear waste will be immobilized at the Savannah River Site (SRS) by vitrification in borosilicate glass. To fulfill this requirement, glass samples were heat treated at various times and temperatures. These results will provide guidance to the repository program about conditions to be avoided during shipping, handling and storage of DWPF canistered waste forms.

DWPF Safely Dispositioning Liquid Waste

ScienceCinema

None

2018-06-21

The only operating radioactive waste glassification plant in the nation, the Defense Waste Processing Facility (DWPF) converts the liquid radioactive waste currently stored at the Savannah River Site (SRS) into a solid glass form suitable for long-term storage and disposal. Scientists have long considered this glassification process, called “vitrification,” as the preferred option for treating liquid radioactive waste.

DWPF SIMULANT CPC STUDIES FOR SB7B

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, D.

2011-11-01

Lab-scale DWPF simulations of Sludge Batch 7b (SB7b) processing were performed. Testing was performed at the Savannah River National Laboratory - Aiken County Technology Laboratory (SRNL-ACTL). The primary goal of the simulations was to define a likely operating window for acid stoichiometry for the DWPF Sludge Receipt and Adjustment Tank (SRAT). In addition, the testing established conditions for the SRNL Shielded Cells qualification simulation of SB7b-Tank 40 blend, supported validation of the current glass redox model, and validated the coupled process flowsheet at the nominal acid stoichiometry. An acid window of 105-140% by the Koopman minimum acid (KMA) equation (107-142%more » DWPF Hsu equation) worked for the sludge-only flowsheet. Nitrite was present in the SRAT product for the 105% KMA run at 366 mg/kg, while SME cycle hydrogen reached 94% of the DWPF Slurry Mix Evaporator (SME) cycle limit in the 140% KMA run. The window was determined for sludge with added caustic (0.28M additional base, or roughly 12,000 gallons 50% NaOH to 820,000 gallons waste slurry). A suitable processing window appears to be 107-130% DWPF acid equation for sludge-only processing allowing some conservatism for the mapping of lab-scale simulant data to full-scale real waste processing including potentially non-conservative noble metal and mercury concentrations. This window should be usable with or without the addition of up to 7,000 gallons of caustic to the batch. The window could potentially be wider if caustic is not added to SB7b. It is recommended that DWPF begin processing SB7b at 115% stoichiometry using the current DWPF equation. The factor could be increased if necessary, but changes should be made with caution and in small increments. DWPF should not concentrate past 48 wt.% total solids in the SME cycle if moderate hydrogen generation is occurring simultaneously. The coupled flowsheet simulation made more hydrogen in the SRAT and SME cycles than the sludge-only run with the same acid stoichiometric factor. The slow acid addition in MCU seemed to alter the reactions that consumed the small excess acid present such that hydrogen generation was promoted relative to sludge-only processing. The coupled test reached higher wt.% total solids, and this likely contributed to the SME cycle hydrogen limit being exceeded at 110% KMA. It is clear from the trends in the SME processing GC data, however, that the frit slurry formic acid contributed to driving the hydrogen generation rate above the SME cycle limit. Hydrogen generation rates after the second frit addition generally exceeded those after the first frit addition. SRAT formate loss increased with increasing acid stoichiometry (15% to 35%). A substantial nitrate gain which was observed to have occurred after acid addition (and nitrite destruction) was reversed to a net nitrate loss in runs with higher acid stoichiometry (nitrate in SRAT product less than sum of sludge nitrate and added nitric acid). Increased ammonium ion formation was also indicated in the runs with nitrate loss. Oxalate loss on the order 20% was indicated in three of the four acid stoichiometry runs and in the coupled flowsheet run. The minimum acid stoichiometry run had no indicated loss. The losses were of the same order as the official analytical uncertainty of the oxalate concentration measurement, but were not randomly distributed about zero loss, so some actual loss was likely occurring. Based on the entire set of SB7b test data, it is recommended that DWPF avoid concentrating additional sludge solids in single SRAT batches to limit the concentrations of noble metals to SB7a processing levels (on a grams noble metal per SRAT batch basis). It is also recommended that DWPF drop the formic acid addition that accompanies the process frit 418 additions, since SME cycle data showed considerable catalytic activity for hydrogen generation from this additional acid (about 5% increase in stoichiometry occurred from the frit formic acid). Frit 418 also does not appear to need formic acid addition to prevent gel formation in the frit slurry. Simulant processing was successful using 100 ppm of 747 antifoam added prior to nitric acid instead of 200 ppm. This is a potential area for DWPF to cut antifoam usage in any future test program. An additional 100 ppm was added before formic acid addition. Foaming during formic acid addition was not observed. No build-up of oily or waxy material was observed in the off-gas equipment. Lab-scale mercury stripping behavior was similar to SB6 and SB7a. More mercury was unaccounted for as the acid stoichiometry increased.« less

SUMMARY OF FY11 SULFATE RETENTION STUDIES FOR DEFENSE WASTE PROCESSING FACILITY GLASS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K.; Edwards, T.

2012-05-08

This report describes the results of studies related to the incorporation of sulfate in high level waste (HLW) borosilicate glass produced at the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF). A group of simulated HLW glasses produced for earlier sulfate retention studies was selected for full chemical composition measurements to determine whether there is any clear link between composition and sulfate retention over the compositional region evaluated. In addition, the viscosity of several glasses was measured to support future efforts in modeling sulfate solubility as a function of predicted viscosity. The intent of these studies was to developmore » a better understanding of sulfate retention in borosilicate HLW glass to allow for higher loadings of sulfate containing waste. Based on the results of these and other studies, the ability to improve sulfate solubility in DWPF borosilicate glasses lies in reducing the connectivity of the glass network structure. This can be achieved, as an example, by increasing the concentration of alkali species in the glass. However, this must be balanced with other effects of reduced network connectivity, such as reduced viscosity, potentially lower chemical durability, and in the case of higher sodium and aluminum concentrations, the propensity for nepheline crystallization. Future DWPF processing is likely to target higher waste loadings and higher sludge sodium concentrations, meaning that alkali concentrations in the glass will already be relatively high. It is therefore unlikely that there will be the ability to target significantly higher total alkali concentrations in the glass solely to support increased sulfate solubility without the increased alkali concentration causing failure of other Product Composition Control System (PCCS) constraints, such as low viscosity and durability. No individual components were found to provide a significant improvement in sulfate retention (i.e., an increase of the magnitude necessary to have a dramatic impact on blending, washing, or waste loading strategies for DWPF) for the glasses studied here. In general, the concentrations of those species that significantly improve sulfate solubility in a borosilicate glass must be added in relatively large concentrations (e.g., 13 to 38 wt % or more of the frit) in order to have a substantial impact. For DWPF, these concentrations would constitute too large of a portion of the frit to be practical. Therefore, it is unlikely that specific additives may be introduced into the DWPF glass via the frit to significantly improve sulfate solubility. The results presented here continue to show that sulfate solubility or retention is a function of individual glass compositions, rather than a property of a broad glass composition region. It would therefore be inappropriate to set a single sulfate concentration limit for a range of DWPF glass compositions. Sulfate concentration limits should continue to be identified and implemented for each sludge batch. The current PCCS limit is 0.4 wt % SO{sub 4}{sup 2-} in glass, although frit development efforts have led to an increased limit of 0.6 wt % for recent sludge batches. Slightly higher limits (perhaps 0.7-0.8 wt %) may be possible for future sludge batches. An opportunity for allowing a higher sulfate concentration limit at DWPF may lay lie in improving the laboratory experiments used to set this limit. That is, there are several differences between the crucible-scale testing currently used to define a limit for DWPF operation and the actual conditions within the DWPF melter. In particular, no allowance is currently made for sulfur partitioning (volatility versus retention) during melter processing as the sulfate limit is set for a specific sludge batch. A better understanding of the partitioning of sulfur in a bubbled melter operating with a cold cap as well as the impacts of sulfur on the off-gas system may allow a higher sulfate concentration limit to be established for the melter feed. This approach would have to be taken carefully to ensure that a sulfur salt layer is not formed on top of the melt pool while allowing higher sulfur based feeds to be processed through DWPF.« less

SIMULANT DEVELOPMENT FOR SAVANNAH RIVER SITE HIGH LEVEL WASTE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M; Russell Eibling, R; David Koopman, D

2007-09-04

The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste (HLW) for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides (primarily iron, aluminum, magnesium, manganese, and uranium) and soluble sodium salts (carbonate, hydroxide, nitrite, nitrate, and sulfate). The HLW is processed in large batches through DWPF; DWPF has recently completed processing Sludge Batch 3 (SB3) and is currently processing Sludge Batch 4 (SB4). The composition of metal species in SB4 is shown in Table 1 as a function of the ratiomore » of a metal to iron. Simulants remove radioactive species and renormalize the remaining species. Supernate composition is shown in Table 2.« less

Short Term Weather Forecasting in Real Time in a Base Weather Station Setting

DTIC Science & Technology

1993-10-01

SMSL DWPF Figure 25. Plot of surface airways observations at 18 UTC, I April 1993. Data is plotted in conventional notation. 35 mu eb 23 -:.-j-32 29292 3...34 38 3 ... .. :......:.. . . O0i-02-93 0600 GMT CLCT TMPF WSYM SMSL DWPF Figure 26. As in Figure 25, except for 06 UTC, 2 April 1993. 36 Figure 27

EVALUATION OF REQUIREMENTS FOR THE DWPF HIGHER CAPACITY CANISTER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.; Estochen, E.; Jordan, J.

2014-08-05

The Defense Waste Processing Facility (DWPF) is considering the option to increase canister glass capacity by reducing the wall thickness of the current production canister. This design has been designated as the DWPF Higher Capacity Canister (HCC). A significant decrease in the number of canisters processed during the life of the facility would be achieved if the HCC were implemented leading to a reduced overall reduction in life cycle costs. Prior to implementation of the change, Savannah River National Laboratory (SRNL) was requested to conduct an evaluation of the potential impacts. The specific areas of interest included loading and deformationmore » of the canister during the filling process. Additionally, the effect of the reduced wall thickness on corrosion and material compatibility needed to be addressed. Finally the integrity of the canister during decontamination and other handling steps needed to be determined. The initial request regarding canister fabrication was later addressed in an alternate study. A preliminary review of canister requirements and previous testing was conducted prior to determining the testing approach. Thermal and stress models were developed to predict the forces on the canister during the pouring and cooling process. The thermal model shows the HCC increasing and decreasing in temperature at a slightly faster rate than the original. The HCC is shown to have a 3°F ΔT between the internal and outer surfaces versus a 5°F ΔT for the original design. The stress model indicates strain values ranging from 1.9% to 2.9% for the standard canister and 2.5% to 3.1% for the HCC. These values are dependent on the glass level relative to the thickness transition between the top head and the canister wall. This information, along with field readings, was used to set up environmental test conditions for corrosion studies. Small 304-L canisters were filled with glass and subjected to accelerated environmental testing for 3 months. No evidence of stress corrosion cracking was indicated on either the canisters or U-bend coupons. Calculations and finite element modeling were used to determine forces over a range of handling conditions along with possible forces during decontamination. While expected reductions in some physical characteristics were found in the HCC, none were found to be significant when compared to the required values necessary to perform its intended function. Based on this study and a review of successful testing of thinner canisters at West Valley Demonstration Project (WVDP), the mechanical properties obtained with the thinner wall do not significantly undermine the ability of the canister to perform its intended function.« less

REDUCTION OF CONSTRAINTS FOR COUPLED OPERATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raszewski, F.; Edwards, T.

2009-12-15

The homogeneity constraint was implemented in the Defense Waste Processing Facility (DWPF) Product Composition Control System (PCCS) to help ensure that the current durability models would be applicable to the glass compositions being processed during DWPF operations. While the homogeneity constraint is typically an issue at lower waste loadings (WLs), it may impact the operating windows for DWPF operations, where the glass forming systems may be limited to lower waste loadings based on fissile or heat load limits. In the sludge batch 1b (SB1b) variability study, application of the homogeneity constraint at the measurement acceptability region (MAR) limit eliminated muchmore » of the potential operating window for DWPF. As a result, Edwards and Brown developed criteria that allowed DWPF to relax the homogeneity constraint from the MAR to the property acceptance region (PAR) criterion, which opened up the operating window for DWPF operations. These criteria are defined as: (1) use the alumina constraint as currently implemented in PCCS (Al{sub 2}O{sub 3} {ge} 3 wt%) and add a sum of alkali constraint with an upper limit of 19.3 wt% ({Sigma}M{sub 2}O < 19.3 wt%), or (2) adjust the lower limit on the Al{sub 2}O{sub 3} constraint to 4 wt% (Al{sub 2}O{sub 3} {ge} 4 wt%). Herman et al. previously demonstrated that these criteria could be used to replace the homogeneity constraint for future sludge-only batches. The compositional region encompassing coupled operations flowsheets could not be bounded as these flowsheets were unknown at the time. With the initiation of coupled operations at DWPF in 2008, the need to revisit the homogeneity constraint was realized. This constraint was specifically addressed through the variability study for SB5 where it was shown that the homogeneity constraint could be ignored if the alumina and alkali constraints were imposed. Additional benefit could be gained if the homogeneity constraint could be replaced by the Al{sub 2}O{sub 3} and sum of alkali constraint for future coupled operations processing based on projections from Revision 14 of the High Level Waste (HLW) System Plan. As with the first phase of testing for sludge-only operations, replacement of the homogeneity constraint with the alumina and sum of alkali constraints will ensure acceptable product durability over the compositional region evaluated. Although these study glasses only provide limited data in a large compositional region, the approach and results are consistent with previous studies that challenged the homogeneity constraint for sludge-only operations. That is, minimal benefit is gained by imposing the homogeneity constraint if the other PCCS constraints are satisfied. The normalized boron releases of all of the glasses are well below the Environmental Assessment (EA) glass results, regardless of thermal history. Although one of the glasses had a normalized boron release of approximately 10 g/L and was not predictable, the glass is still considered acceptable. This particular glass has a low Al{sub 2}O{sub 3} concentration, which may have attributed to the anomalous behavior. Given that poor durability has been previously observed in other glasses with low Al{sub 2}O{sub 3} and Fe{sub 2}O{sub 3} concentrations, including the sludge-only reduction of constraints study, further investigations appear to be warranted. Based on the results of this study, it is recommended that the homogeneity constraint (in its entirety with the associated low frit/high frit constraints) be eliminated for coupled operations as defined by Revision 14 of the HLW System Plan with up to 2 wt% TiO{sub 2}. The use of the alumina and sum of alkali constraints should be continued along with the variability study to determine the predictability of the current durability models and/or that the glasses are acceptable with respect to durability. The use of a variability study for each batch is consistent with the glass product control program and it will help to assess new streams or compositional changes. It is also recommended that the influence of alumina and alkali on durability be studied in greater detail. Limited data suggests that there may be a need to adjust the lower Al{sub 2}O{sub 3} limit and/or the upper alkali limit in order to prevent the fabrication of unacceptable glasses. An in-depth evaluation of all previous data as well as any new data would help to better define an alumina and alkali combination that would avoid potential phase separation and ensure glass durability.« less

Nitric-glycolic flowsheet testing for maximum hydrogen generation rate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, C. J.; Newell, J. D.; Williams, M. S.

The Defense Waste Processing Facility (DWPF) at the Savannah River Site is developing for implementation a flowsheet with a new reductant to replace formic acid. Glycolic acid has been tested over the past several years and found to effectively replace the function of formic acid in the DWPF chemical process. The nitric-glycolic flowsheet reduces mercury, significantly lowers the chemical generation of hydrogen and ammonia, allows purge reduction in the Sludge Receipt and Adjustment Tank (SRAT), stabilizes the pH and chemistry in the SRAT and the Slurry Mix Evaporator (SME), allows for effective adjustment of the SRAT/SME rheology, and is favorablemore » with respect to melter flammability. The objective of this work was to perform DWPF Chemical Process Cell (CPC) testing at conditions that would bound the catalytic hydrogen production for the nitric-glycolic flowsheet.« less

Literature Review: Assessment of DWPF Melter and Melter Off-gas System Lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M.

2015-07-30

Testing to date for the MOC for the Hanford Waste Treatment and Immobilization Plant (WTP) melters is being reviewed with the lessons learned from DWPF in mind and with consideration to the changes in the flowsheet/feed compositions that have occurred since the original testing was performed. This information will be presented in a separate technical report that identifies any potential gaps for WTP processing.

DWPF STARTUP FRIT VISCOSITY MEASUREMENT ROUND ROBIN RESULTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crum, Jarrod V.; Edwards, Tommy B.; Russell, Renee L.

2012-07-31

A viscosity standard is needed to replace the National Institute of Standards and Technology (NIST) glasses currently being used to calibrate viscosity measurement equipment. The current NIST glasses are either unavailable or less than ideal for calibrating equipment to measure the viscosity of high-level waste glasses. This report documents the results of a viscosity round robin study conducted on the Defense Waste Processing Facility (DWPF) startup frit. DWPF startup frit was selected because its viscosity-temperature relationship is similar to most DWPF and Hanford high-level waste glass compositions. The glass underwent grinding and blending to homogenize the large (100 lb) batch.more » Portions of the batch were supplied to the laboratories (named A through H) for viscosity measurements following a specified temperature schedule with a temperature range of 1150 C to 950 C and with an option to measure viscosity at lower temperatures if their equipment was capable of measuring at the higher viscosities. Results were used to fit the Vogel-Tamman-Fulcher and Arrhenius equations to viscosity as a function of temperature for the entire temperature range of 460 C through 1250 C as well as the limited temperature interval of approximately 950 C through 1250 C. The standard errors for confidence and prediction were determined for the fitted models.« less

Actual waste demonstration of the nitric-glycolic flowsheet for sludge batch 9 qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newell, D.; Pareizs, J.; Martino, C.

For each sludge batch that is processed in the Defense Waste Processing Facility (DWPF), the Savannah River National Laboratory (SRNL) performs qualification testing to demonstrate that the sludge batch is processable. Based on the results of this actual-waste qualification and previous simulant studies, SRNL recommends implementation of the nitric-glycolic acid flowsheet in DWPF. Other recommendations resulting from this demonstration are reported in section 5.0.

IMPROVED ANTIFOAM AGENT STUDY END OF YEAR REPORT, EM PROJECT 3.2.3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D.; Koopman, D.; Newell, J.

2011-09-30

Antifoam 747 is added to minimize foam produced by process gases and water vapor during chemical processing of sludge in the Defense Waste Processing Facility (DWPF). This allows DWPF to maximize acid addition and evaporation rates to minimize the cycle time in the Chemical Processing Cell (CPC). Improvements in DWPF melt rate due to the addition of bubblers in the melter have resulted in the need for further reductions in cycle time in the CPC. This can only be accomplished with an effective antifoam agent. DWPF production was suspended on March 22, 2011 as the result of a Flammable Gasmore » New Information/(NI) Potential Inadequacy in the Safety Analysis (PISA). The issue was that the DWPF melter offgas flammability strategy did not take into account the H and C in the antifoam, potentially flammable components, in the melter feed. It was also determined the DWPF was using much more antifoam than anticipated due to a combination of longer processing in the CPC due to high Hg, longer processing due to Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) additions, and adding more antifoam than recommended. The resolution to the PISA involved and assessment of the impact of the antifoam on melter flammability and the implementation of a strategy to control additions within acceptable levels. This led to the need to minimize the use of Antifoam 747 in processing beginning in May 2011. DWPF has had limited success in using Antifoam 747 in caustic processing. Since starting up the ARP facility, the ARP product (similar chemically to caustic sludge) is added to the Sludge Receipt and Adjustment Tank (SRAT) at boiling and evaporated to maintain a constant SRAT volume. Although there is very little offgas generated during caustic boiling, there is a large volume of water vapor produced which can lead to foaming. High additions and more frequent use of antifoam are used to mitigate the foaming during caustic boiling. The result of these three issues above is that DWPF had three antifoam needs in FY2011: (1) Determine the cause of the poor Antifoam 747 performance during caustic boiling; (2) Determine the decomposition products of Antifoam 747 during CPC processing; and (3) Improve the effectiveness of Antifoam 747, in order to minimize the amount used. Testing was completed by Illinois Institute of Technology (IIT) and Savannah River National Laboratory (SRNL) researchers to address these questions. The testing results reported were funded by both DWPF and DOE/EM 31. Both sets of results are reported in this document for completeness. The results of this research are summarized: (1) The cause for the poor Antifoam 747 performance during caustic boiling was the high hydrolysis rate, cleaving the antifoam molecule in two, leading to poor antifoam performance. In testing with pH solutions from 1 to 13, the antifoam degraded quickly at a pH < 4 and pH > 10. As the antifoam decomposed it lost its spreading ability (wetting agent performance), which is crucial to its antifoaming performance. During testing of a caustic sludge simulants, there was more foam in tests with added Antifoam 747 than in tests without added antifoam. (2) Analyses were completed to determine the composition of the two antifoam components and Antifoam 747. In addition, the decomposition products of Antifoam 747 were determined during CPC processing of sludge simulants. The main decomposition products were identified primarily as Long Chain Siloxanes, boiling point > 400 C. Total antifoam recovery was 33% by mass. In a subsequent study, various compounds potentially related to antifoam were found using semi-volatile organic analysis and volatile organic analysis on the hexane extractions and hexane rinses. These included siloxanes, trimethyl silanol, methoxy trimethyl silane, hexamethyl disiloxane, aliphatic hydrocarbons, dioctyl phthalate, and emulsifiers. Cumulatively, these species amounted to less than 3% of the antifoam mass. The majority of the antifoam was identified using carbon analysis of the SRAT product (40-80% by mass) and silicon analysis (23-83% by mass) of the condensate. Both studies recommended a better solvent for antifoam and more specific tests for antifoam degradation products than the Si and C analyses used. (3) The DWPF Antifoam 747 Purchase Specification was revised in Month, 2011 with a goal of increasing the quality of Antifoam 747. The purchase specification was changed to specify the manufacturer and product for both components that are blended by Siovation to produce Antifoam 747 for DWPF. Testing of Antifoam produced using both the old and new antifoam specifications perform very similarly in testing. Since the change in purchase specification has not improved antifoam performance, an improved antifoam agent is required.« less

Corrosion Testing of Monofrax K-3 Refractory in Defense Waste Processing Facility (DWPF) Alternate Reductant Feeds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, M.; Jantzen, C.; Burket, P.

The Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS) uses a combination of reductants and oxidants while converting high level waste (HLW) to a borosilicate waste form. A reducing flowsheet is maintained to retain radionuclides in their reduced oxidation states which promotes their incorporation into borosilicate glass. For the last 20 years of processing, the DWPF has used formic acid as the main reductant and nitric acid as the main oxidant. During reaction in the Chemical Process Cell (CPC), formate and formic acid release measurably significant H 2 gas which requires monitoring of certain vessel’s vapor spaces.more » A switch to a nitric acid-glycolic acid (NG) flowsheet from the nitric-formic (NF) flowsheet is desired as the NG flowsheet releases considerably less H 2 gas upon decomposition. This would greatly simplify DWPF processing from a safety standpoint as close monitoring of the H 2 gas concentration could become less critical. In terms of the waste glass melter vapor space flammability, the switch from the NF flowsheet to the NG flowsheet showed a reduction of H 2 gas production from the vitrification process as well. Due to the positive impact of the switch to glycolic acid determined on the flammability issues, evaluation of the other impacts of glycolic acid on the facility must be examined.« less

Integration of the Uncertainties of Anion and TOC Measurements into the Flammability Control Strategy for Sludge Batch 8 at the DWPF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T. B.

2013-03-14

The Savannah River National Laboratory (SRNL) has been working with the Savannah River Remediation (SRR) Defense Waste Processing Facility (DWPF) in the development and implementation of a flammability control strategy for DWPF’s melter operation during the processing of Sludge Batch 8 (SB8). SRNL’s support has been in response to technical task requests that have been made by SRR’s Waste Solidification Engineering (WSE) organization. The flammability control strategy relies on measurements that are performed on Slurry Mix Evaporator (SME) samples by the DWPF Laboratory. Measurements of nitrate, oxalate, formate, and total organic carbon (TOC) standards generated by the DWPF Laboratory aremore » presented in this report, and an evaluation of the uncertainties of these measurements is provided. The impact of the uncertainties of these measurements on DWPF’s strategy for controlling melter flammability also is evaluated. The strategy includes monitoring each SME batch for its nitrate content and its TOC content relative to the nitrate content and relative to the antifoam additions made during the preparation of the SME batch. A linearized approach for monitoring the relationship between TOC and nitrate is developed, equations are provided that integrate the measurement uncertainties into the flammability control strategy, and sample calculations for these equations are shown to illustrate the impact of the uncertainties on the flammability control strategy.« less

Results from tests of TFL Hydragard sampling loop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steimke, J.L.

When the Defense Waste Processing Facility (DWPF) is operational, processed radioactive sludge will be transferred in batches to the Slurry Mix Evaporator (SME), where glass frit will be added and the contents concentrated by boiling. Batches of the slurry mixture are transferred from the SME to the Melter Feed Tank (MFT). Hydragard{reg_sign} sampling systems are used on the SME and the MFT for collecting slurry samples in vials for chemical analysis. An accurate replica of the Hydragard sampling system was built and tested in the thermal Fluids Laboratory (TFL) to determine the hydragard accuracy. It was determined that the originalmore » Hydragard valve frequently drew a non-representative sample stream through the sample vial that ranged from frit enriched to frit depleted. The Hydragard valve was modified by moving the plunger and its seat backwards so that the outer surface of the plunger was flush with the inside diameter of the transfer line when the valve was open. The slurry flowing through the vial accurately represented the composition of the slurry in the reservoir for two types of slurries, different dilution factors, a range of transfer flows and a range of vial flows. It was then found that the 15 ml of slurry left in the vial when the Hydragard valve was closed, which is what will be analyzed at DWPF, had a lower ratio of frit to sludge as characterized by the lithium to iron ratio than the slurry flowing through it. The reason for these differences is not understood at this time but it is recommended that additional experimentation be performed with the TFL Hydragard loop to determine the cause.« less

Specific Adaptation of Gas Atomization Processing for Al-Based Alloy Powder for Additive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Iver; Siemon, John

The initial three atomization attempts resulted in “freeze-outs” within the pour tubes in the pilot-scale system and yielded no powder. Re-evaluation of the alloy liquidus temperatures and melting characteristics, in collaboration with Alcoa, showed further superheat to be necessary to allow the liquid metal to flow through the pour tube to the atomization nozzle. A subsequent smaller run on the experimental atomization system verified these parameters and was successful, as were all successive runs on the larger pilot scale system. One alloy composition froze-out part way through the atomization on both pilot scale runs. SEM images showed needle formation andmore » phase segregations within the microstructure. Analysis of the pour tube freeze-out microstructures showed that large needles formed within the pour tube during the atomization experiment, which eventually blocked the melt stream. Alcoa verified the needle formation in this alloy using theoretical modeling of phase solidification. Sufficient powder of this composition was still generated to allow powder characterization and additive manufacturing trials at Alcoa.« less

Antifoam degradation testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D. P.; Zamecnik, J. R.; Newell, D. D.

2015-08-20

This report describes the results of testing to quantify the degradation products resulting from the dilution and storage of Antifoam 747. Antifoam degradation is of concern to the Defense Waste Processing Facility (DWPF) due to flammable decomposition products in the vapor phase of the Chemical Process Cell vessels, as well as the collection of flammable and organic species in the offgas condensate. The discovery that hexamethyldisiloxane is formed from the antifoam decomposition was the basis for a Potential Inadequacy in the Safety Analysis declaration by the DWPF.

SLURRY MIX EVAPORATOR BATCH ACCEPTABILITY AND TEST CASES OF THE PRODUCT COMPOSITION CONTROL SYSTEM WITH THORIUM AS A REPORTABLE ELEMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.

2010-10-07

The Defense Waste Processing Facility (DWPF), which is operated by Savannah River Remediation, LLC (SRR), has recently begun processing Sludge Batch 6 (SB6) by combining it with Frit 418 at a nominal waste loading (WL) of 36%. A unique feature of the SB6/Frit 418 glass system, as compared to the previous glass systems processed in DWPF, is that thorium will be a reportable element (i.e., concentrations of elemental thorium in the final glass product greater than 0.5 weight percent (wt%)) for the resulting wasteform. Several activities were initiated based upon this unique aspect of SB6. One of these was anmore » investigation into the impact of thorium on the models utilized in DWPF's Product Composition and Control System (PCCS). While the PCCS is described in more detail below, for now note that it is utilized by Waste Solidification Engineering (WSE) to evaluate the acceptability of each batch of material in the Slurry Mix Evaporator (SME) before this material is passed on to the melter. The evaluation employs models that predict properties associated with processability and product quality from the composition of vitrified samples of the SME material. The investigation of the impact of thorium on these models was conducted by Peeler and Edwards [1] and led to a recommendation that DWPF can process the SB6/Frit 418 glass system with ThO{sub 2} concentrations up to 1.8 wt% in glass. Questions also arose regarding the handling of thorium in the SME batch acceptability process as documented by Brown, Postles, and Edwards [2]. Specifically, that document is the technical bases of PCCS, and while Peeler and Edwards confirmed the reliability of the models, there is a need to confirm that the current implementation of DWPF's PCCS appropriately handles thorium as a reportable element. Realization of this need led to a Technical Task Request (TTR) prepared by Bricker [3] that identified some specific SME-related activities that the Savannah River National Laboratory (SRNL) was requested to conduct. SRNL issued a Task Technical and Quality Assurance (TT&QA) plan [4] in response to the SRR request. The conclusions provided in this report are that no changes need to be made to the SME acceptability process (i.e., no modifications to WSRC-TR-95-00364, Revision 5, are needed) and no changes need to be made to the Product Composition Control System (PCCS) itself (i.e. the spreadsheet utilized by Waste Solidification Engineering (WSE) for acceptability decisions does not require modification) in response to thorium becoming a reportable element for DWPF operations. In addition, the inputs and results for the two test cases requested by WSE for use in confirming the successful activation of thorium as a reportable element for DWPF operations during the processing of SB6 are presented in this report.« less

DWPF Melter Off-Gas Flammability Assessment for Sludge Batch 9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, A. S.

2016-07-11

The slurry feed to the Defense Waste Processing Facility (DWPF) melter contains several organic carbon species that decompose in the cold cap and produce flammable gases that could accumulate in the off-gas system and create potential flammability hazard. To mitigate such a hazard, DWPF has implemented a strategy to impose the Technical Safety Requirement (TSR) limits on all key operating variables affecting off-gas flammability and operate the melter within those limits using both hardwired/software interlocks and administrative controls. The operating variables that are currently being controlled include; (1) total organic carbon (TOC), (2) air purges for combustion and dilution, (3)more » melter vapor space temperature, and (4) feed rate. The safety basis limits for these operating variables are determined using two computer models, 4-stage cold cap and Melter Off-Gas (MOG) dynamics models, under the baseline upset scenario - a surge in off-gas flow due to the inherent cold cap instabilities in the slurry-fed melter.« less

HLW system plan - revision 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-01-14

The projected ability of the Tank Farm to support DWPF startup and continued operation has diminished somewhat since revision 1 of this Plan. The 13 month delay in DWPF startup, which actually helps the Tank Farm condition in the near term, was more than offset by the 9 month delay in ITP startup, the delay in the Evaporator startups and the reduction to Waste Removal funding. This Plan does, however, describe a viable operating strategy for the success of the HLW System and Mission, albeit with less contingency and operating flexibility than in the past. HLWM has focused resources frommore » within the division on five near term programs: The three evaporator restarts, DWPF melter heatup and completion of the ITP outage. The 1H Evaporator was restarted 12/28/93 after a 9 month shutdown for an extensive Conduct of Operations upgrade. The 2F and 2H Evaporators are scheduled to restart 3/94 and 4/94, respectively. The RHLWE startup remains 11/17/97.« less

Production of Jet Fuels from Coal Derived Liquids. Volume 6. Preliminary Analysis of Upgrading Alternatives for the Great Plains Liquid By-Production Streams

DTIC Science & Technology

1988-09-01

be easily hydrogenated to produce highly naphthenic JP-4 blendstock, but the hydrogen consumption is very high, around 5,000 SCFB. Distillation...The naphtha stream is characterized by analyses shown in Table 4 and distillation results in Figure 7. Comparison of as-received and caustic ... Naphthenes , min. 70 it , max. 90 Reid Vapor Pressure,min. 2.0 f to it ,max. 3.0 Flash Point, OF, min. 100 122 Pour Point, OF, max. -72 -62 Gasoline

ACTUAL WASTE TESTING OF GYCOLATE IMPACTS ON THE SRS TANK FARM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, C.

2014-05-28

Glycolic acid is being studied as a replacement for formic acid in the Defense Waste Processing Facility (DWPF) feed preparation process. After implementation, the recycle stream from DWPF back to the high-level waste Tank Farm will contain soluble sodium glycolate. Most of the potential impacts of glycolate in the Tank Farm were addressed via a literature review and simulant testing, but several outstanding issues remained. This report documents the actual-waste tests to determine the impacts of glycolate on storage and evaporation of Savannah River Site high-level waste. The objectives of this study are to address the following: Determine the extentmore » to which sludge constituents (Pu, U, Fe, etc.) dissolve (the solubility of sludge constituents) in the glycolate-containing 2H-evaporator feed. Determine the impact of glycolate on the sorption of fissile (Pu, U, etc.) components onto sodium aluminosilicate solids. The first objective was accomplished through actual-waste testing using Tank 43H and 38H supernatant and Tank 51H sludge at Tank Farm storage conditions. The second objective was accomplished by contacting actual 2H-evaporator scale with the products from the testing for the first objective. There is no anticipated impact of up to 10 g/L of glycolate in DWPF recycle to the Tank Farm on tank waste component solubilities as investigated in this test. Most components were not influenced by glycolate during solubility tests, including major components such as aluminum, sodium, and most salt anions. There was potentially a slight increase in soluble iron with added glycolate, but the soluble iron concentration remained so low (on the order of 10 mg/L) as to not impact the iron to fissile ratio in sludge. Uranium and plutonium appear to have been supersaturated in 2H-evaporator feed solution mixture used for this testing. As a result, there was a reduction of soluble uranium and plutonium as a function of time. The change in soluble uranium concentration was independent of added glycolate concentration. The change in soluble plutonium content was dependent on the added glycolate concentration, with higher levels of glycolate (5 g/L and 10 g/L) appearing to suppress the plutonium solubility. The inclusion of glycolate did not change the dissolution of or sorption onto actual-waste 2H-evaporator pot scale to an extent that will impact Tank Farm storage and concentration. The effects that were noted involved dissolution of components from evaporator scale and precipitation of components onto evaporator scale that were independent of the level of added glycolate.« less

Examination Of Sulfur Measurements In DWPF Sludge Slurry And SRAT Product Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.; Wiedenman, B. J.

2012-11-29

Savannah River National Laboratory (SRNL) was asked to re-sample the received SB7b WAPS material for wt. % solids, perform an aqua regia digestion and analyze the digested material by inductively coupled plasma - atomic emission spectroscopy (ICP-AES), as well as re-examine the supernate by ICP-AES. The new analyses were requested in order to provide confidence that the initial analytical subsample was representative of the Tank 40 sample received and to replicate the S results obtained on the initial subsample collected. The ICP-AES analyses for S were examined with both axial and radial detection of the sulfur ICP-AES spectroscopic emission linesmore » to ascertain if there was any significant difference in the reported results. The outcome of this second subsample of the Tank 40 WAPS material is the first subject of this report. After examination of the data from the new subsample of the SB7b WAPS material, a team of DWPF and SRNL staff looked for ways to address the question of whether there was in fact insoluble S that was not being accounted for by ion chromatography (IC) analysis. The question of how much S is reaching the melter was thought best addressed by examining a DWPF Slurry Mix Evaporator (SME) Product sample, but the significant dilution of sludge material, containing the S species in question, that results from frit addition was believed to add additional uncertainty to the S analysis of SME Product material. At the time of these discussions it was believed that all S present in a Sludge Receipt and Adjustment Tank (SRAT) Receipt sample would be converted to sulfate during the course of the SRAT cycle. A SRAT Product sample would not have the S dilution effect resulting from frit addition, and hence, it was decided that a DWPF SRAT Product sample would be obtained and submitted to SRNL for digestion and sample preparation followed by a round-robin analysis of the prepared samples by the DWPF Laboratory, F/H Laboratories, and SRNL for S and sulfate. The results of this round-robin analytical study are the second subject of this report.« less

Defense Waste Processing Facility Simulant Chemical Processing Cell Studies for Sludge Batch 9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Tara E.; Newell, J. David; Woodham, Wesley H.

The Savannah River National Laboratory (SRNL) received a technical task request from Defense Waste Processing Facility (DWPF) and Saltstone Engineering to perform simulant tests to support the qualification of Sludge Batch 9 (SB9) and to develop the flowsheet for SB9 in the DWPF. These efforts pertained to the DWPF Chemical Process Cell (CPC). CPC experiments were performed using SB9 simulant (SB9A) to qualify SB9 for sludge-only and coupled processing using the nitric-formic flowsheet in the DWPF. Two simulant batches were prepared, one representing SB8 Tank 40H and another representing SB9 Tank 51H. The simulant used for SB9 qualification testing wasmore » prepared by blending the SB8 Tank 40H and SB9 Tank 51H simulants. The blended simulant is referred to as SB9A. Eleven CPC experiments were run with an acid stoichiometry ranging between 105% and 145% of the Koopman minimum acid equation (KMA), which is equivalent to 109.7% and 151.5% of the Hsu minimum acid factor. Three runs were performed in the 1L laboratory scale setup, whereas the remainder were in the 4L laboratory scale setup. Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) cycles were performed on nine of the eleven. The other two were SRAT cycles only. One coupled flowsheet and one extended run were performed for SRAT and SME processing. Samples of the condensate, sludge, and off-gas were taken to monitor the chemistry of the CPC experiments.« less

Results of Hg speciation testing on DWPF SMECT-8, OGCT-1, AND OGCT-2 samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C.

2016-02-22

The Savannah River National Laboratory (SRNL) was tasked with preparing and shipping samples for Hg speciation by Eurofins Frontier Global Sciences, Inc. in Seattle, WA on behalf of the Savannah River Remediation (SRR) Mercury Task Team. The sixteenth shipment of samples was designated to include a Defense Waste Processing Facility (DWPF) Slurry Mix Evaporator Condensate Tank (SMECT) sample from Sludge Receipt and Adjustment Tank (SRAT) Batch 738 processing and two Off-Gas Condensate Tank (OGCT) samples, one following Batch 736 and one following Batch 738. The DWPF sample designations for the three samples analyzed are provided. The Batch 738 ‘End ofmore » SME Cycle’ SMECT sample was taken at the conclusion of Slurry Mix Evaporator (SME) operations for this batch and represents the fourth SMECT sample examined from Batch 738. Batch 738 experienced a sludge slurry carryover event, which introduced sludge solids to the SMECT that were particularly evident in the SMECT-5 sample, but less evident in the ‘End of SME Cycle’ SMECT-8 sample.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sarrack, A.G.

The purpose of this report is to document fault tree analyses which have been completed for the Defense Waste Processing Facility (DWPF) safety analysis. Logic models for equipment failures and human error combinations that could lead to flammable gas explosions in various process tanks, or failure of critical support systems were developed for internal initiating events and for earthquakes. These fault trees provide frequency estimates for support systems failures and accidents that could lead to radioactive and hazardous chemical releases both on-site and off-site. Top event frequency results from these fault trees will be used in further APET analyses tomore » calculate accident risk associated with DWPF facility operations. This report lists and explains important underlying assumptions, provides references for failure data sources, and briefly describes the fault tree method used. Specific commitments from DWPF to provide new procedural/administrative controls or system design changes are listed in the ''Facility Commitments'' section. The purpose of the ''Assumptions'' section is to clarify the basis for fault tree modeling, and is not necessarily a list of items required to be protected by Technical Safety Requirements (TSRs).« less

Impact of Glycolate Anion on Aqueous Corrosion in DWPF and Downstream Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mickalonis, J.

Glycolic acid is being evaluated as an alternate reductant in the preparation of high level waste for the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS). During processing, the glycolic acid may not be completely consumed with small quantities of the glycolate anion being carried forward to other high level waste (HLW) facilities. The SRS liquid waste contractor requested an assessment of the impact of the glycolate anion on the corrosion of the materials of construction (MoC) throughout the waste processing system since this impact had not been previously evaluated. A literature review revealed that corrosion datamore » were not available for the MoCs in glycolic-bearing solutions applicable to SRS systems. Data on the material compatibility with only glycolic acid or its derivative products were identified; however, data were limited for solutions containing glycolic acid or the glycolate anion. For the proprietary coating systems applied to the DWPF concrete, glycolic acid was deemed compatible since the coatings were resistant to more aggressive chemistries than glycolic acid. Additionally, similar coating resins showed acceptable resistance to glycolic acid.« less

Impact of Glycolate Anion on Aqueous Corrosion in DWPF and Downstream Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mickalonis, J.

Glycolic acid is being evaluated as an alternate reductant in the preparation of high level waste for the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS). During processing, the glycolic acid may not be completely consumed with small quantities of the glycolate anion being carried forward to other high level waste (HLW) facilities. The SRS liquid waste contractor requested an assessment of the impact of the glycolate anion on the corrosion of the materials of construction (MoC) throughout the waste processing system since this impact had not been previously evaluated. A literature review revealed that corrosion datamore » were not available for the MoCs in glycolic-bearing solutions applicable to SRS systems. Data on the material compatibility with only glycolic acid or its derivative products were identified; however, data were limited for solutions containing glycolic acid or the glycolate anion. For the proprietary coating systems applied to the DWPF concrete, glycolic acid was deemed compatible since the coatings were resistant to more aggressive chemistries than glycolic acid. Additionally similar coating resins showed acceptable resistance to glycolic acid.« less

Winter Severe Weather: A Case Study of the Intense Squall Line of 6-7 January 1995 in the Carolinas

DTIC Science & Technology

1996-01-01

line. 51 U- U- )C nM-,L Cz2r r Zr’.r - -52 cz bi2 0z CPIu Inu leu bts 533 rMPF DWPF 39 36- 30------- - - - - - - - - - - - - PMiL 014- Gusr DARR 10- 6...14u cz lo0 Go0 Go a- Nr, lou 58 ,t, 7!Ch 59 Lr, CC 7 ~ cr cz 60 z u-, II Zn zc z 11 L1X - CL Aar- c- 61 100 CCu ac- Go 62 mm IflIN Z N _ m 63 TMPF DWPF

Assessment of the impact of the next generation solvent on DWPF melter off-gas flammability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, W. E.

2013-02-13

An assessment has been made to evaluate the impact on the DWPF melter off-gas flammability of replacing the current solvent used in the Modular Caustic-Side Solvent Extraction Process Unit (MCU) process with the Next Generation Solvent (NGS-MCU) and blended solvent. The results of this study showed that the concentrations of nonvolatile carbon and hydrogen of the current solvent in the Slurry Mix Evaporator (SME) product would both be about 29% higher than their counterparts of the NGS-MCU and blended solvent in the absence of guanidine partitioning. When 6 ppm of guanidine (TiDG) was added to the effluent transfer to DWPFmore » to simulate partitioning for the NGS-MCU and blended solvent cases and the concentration of Isopar{reg_sign} L in the effluent transfer was controlled below 87 ppm, the concentrations of nonvolatile carbon and hydrogen of the NGS-MCU and blended solvent were still about 12% and 4% lower, respectively, than those of the current solvent. It is, therefore, concluded that as long as the volume of MCU effluent transfer to DWPF is limited to 15,000 gallons per Sludge Receipt and Adjustment Tank (SRAT)/SME cycle and the concentration of Isopar{reg_sign} L in the effluent transfer is controlled below 87 ppm, using the current solvent assumption of 105 ppm Isopar{reg_sign} L or 150 ppm solvent in lieu of NGS-MCU or blended solvent in the DWPF melter off-gas flammability assessment is conservative for up to an additional 6 ppm of TiDG in the effluent due to guanidine partitioning. This report documents the calculations performed to reach this conclusion.« less

Inhibiting localized corrosion during storage of dilute SRP wastes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oblath, S.B.; Congdon, J.W.

1986-01-01

High-level radioactive waste will be incorporated in borosilicate glass in the Defense Waste Processing Facility (DWPF) at the Savannah River Plant (SRP). As part of this process, large volumes of inorganic salt wastes will be decontaminated for disposal as low-level waste. The principal contaminants, /sup 137/Cs and /sup 90/Sr, are removed by treatment with sodium tetraphenylborate and sodium titanate. The resulting solids will be slurried with a dilute salt solution and stored in existing carbon steel tanks for several years prior to processing and disposal. Initial tests indicated a tendency for localized corrosion of the tanks. An investigation, using nonradioactivemore » simulants for the expected solution compositions, identified inhibitors which would protect the steel. Changes in solution compositions over time, due to radiolytic effects, were also accounted for by the simulants. Six inhibitors were identified which would protect the steel tanks. The effects these inhibitors would have on later processing steps in the DWPF were then evaluated. After this process, only sodium nitrite remained as an inhibitor that was both effective and compatible with the DWPF. The use of this inhibitor has been demonstrated on a real waste slurry.« less

Evaluation of quartz melt rate furnace with the nitric-glycolic flowsheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, M. S.; Miller, D. H.

The Savannah River National Laboratory (SRNL) was tasked to support validation of the Defense Waste Processing Facility (DWPF) melter offgas flammability model for the Nitric-Glycolic (NG) flowsheet. The work is supplemental to the Cold Cap Evaluation Furnace (CEF) testing conducted in 20141 and the Slurry-fed Melt Rate Furnace (SMRF) testing conducted in 20162 that supported Deliverable 4 of the DWPF & Saltstone Facility Engineering Technical Task Request (TTR).3 The Quartz Melt Rate Furnace (QMRF) was evaluated as a bench-scale scoping tool to potentially be used in lieu of or simply prior to the use of the larger-scale SMRF or CEF.more » The QMRF platform has been used previously to evaluate melt rate behavior and offgas compositions of DWPF glasses prepared from the Nitric-Formic (NF) flowsheet but not for the NG flowsheet and not with continuous feeding.4 The overall objective of the 2016-2017 testing was to evaluate the efficacy of the QMRF as a lab-scale platform for steady state, continuously fed melter testing with the NG flowsheet as an alternative to more expensive and complex testing with the SMRF or CEF platforms.« less

ISOLOK VALVE ACCEPTANCE TESTING FOR DWPF SME SAMPLING PROCESS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.; Hera, K.; Coleman, C.

2011-12-05

Evaluation of the Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. Of the opportunities, a focus area related to optimizing the equipment and efficiency of the sample turnaround time for DWPF Analytical Laboratory was identified. The Mechanical Systems & Custom Equipment Development (MS&CED) Section of the Savannah River National Laboratory (SRNL) evaluated the possibility of using an Isolok{reg_sign} sampling valve as an alternative to the Hydragard{reg_sign} valve for taking process samples. Previous viability testing was conducted with favorable results using the Isolok sampler and reported in SRNL-STI-2010-00749 (1).more » This task has the potential to improve operability, reduce maintenance time and decrease CPC cycle time. This report summarizes the results from acceptance testing which was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 (2) and which was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNL-RP-2011-00145 (3). The Isolok to be tested is the same model which was tested, qualified, and installed in the Sludge Receipt Adjustment Tank (SRAT) sample system. RW-0333P QA requirements apply to this task. This task was to qualify the Isolok sampler for use in the DWPF Slurry Mix Evaporator (SME) sampling process. The Hydragard, which is the current baseline sampling method, was used for comparison to the Isolok sampling data. The Isolok sampler is an air powered grab sampler used to 'pull' a sample volume from a process line. The operation of the sampler is shown in Figure 1. The image on the left shows the Isolok's spool extended into the process line and the image on the right shows the sampler retracted and then dispensing the liquid into the sampling container. To determine tank homogeneity, a Coliwasa sampler was used to grab samples at a high and low location within the mixing tank. Data from the two locations were compared to determine if the contents of the tank were well mixed. The Coliwasa sampler is a tube with a stopper at the bottom and is designed to obtain grab samples from specific locations within the drum contents. A position paper (4) was issued to address the prototypic flow loop issues and simulant selections. A statistically designed plan (5) was issued to address the total number of samples each sampler needed to pull, to provide the random order in which samples were pulled and to group samples for elemental analysis. The TTR required that the Isolok sampler perform as well as the Hydragard sampler during these tests to ensure the acceptability of the Isolok sampler for use in the DWPF sampling cells. Procedure No.L9.4-5015 was used to document the sample parameters and process steps. Completed procedures are located in R&D Engineering job folder 23269.« less

DWPF DECON FRIT: SUMP AND SLURRY SOLIDS ANALYSIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.; Peeler, D.; Click, D.

The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. In this report, the physical and chemical characterization results of the slurry solids and sump solids are reported. Crawford et al. (2010) provide the results of the supernate analysis. The results of the sump solidsmore » are reported on a mass basis given the samples were essentially dry upon receipt. The results of the slurry solids were converted to a volume basis given approximately 2.4 grams of slurry solids were obtained from the {approx}4 liters of liquid slurry sample. Although there were slight differences in the analytical results between the sump solids and slurry solids the following general summary statements can be made. Slight differences in the results are also captured for specific analysis. (1) Physical characterization - (a) SEM/EDS analysis suggested that the samples were enriched in Li and Si (B and Na not detectable using the current EDS system) which is consistent with two of the four principle oxides of Frit 418 (B{sub 2}O{sub 3}, Na{sub 2}O, Li{sub 2}O and SiO{sub 2}). (b) SEM/EDS analysis also identified impurities which were elementally consistent with stainless steel (i.e., Fe, Ni, Cr contamination). (c) XRD results indicated that the sump solids samples were amorphous which is consistent with XRD results expected for a Frit 418 based sample. (d) For the sump solids, SEM/EDS analysis indicated that the particle size of the sump solids were consistent with that of an as received Frit 418 sample from a current DWPF vendor. (e) For the slurry solids, SEM/EDS analysis indicated that the particle size range of the slurry solids was much broader than compared to the sump solids. More specifically, there were significantly more fines in the slurry solids as compared to the sump solids. (f) PSD results indicated that > 99% of both the sump and slurry solids were less than 350 microns. The PSD results also supported SEM/EDS analysis that there were significantly more fines in the slurry solids as compared to the sump solids. (2) Weight Percent Solids - Based on the measured supernate density and mass of insoluble solids (2.388 grams) filtered from the four liters of liquid slurry samples, the weight percent insoluble solids was estimated to be 0.060 wt%. This level of insoluble solids is higher than the ETP WAC limit of 100 mg/L, or 0.01 wt% which suggests a separation technology of some type would be required. (3) Chemical Analysis - (a) Elemental results from ICP-ES analysis indicated that the sump solids and slurry were very consistent with the nominal composition of Frit 418. There were other elements identified by ICP analysis which were either consistent with the presence of stainless steel (as identified by SEM/EDS analysis) or impurities that have been observed in 'as received' Frit 418 from the vendor. (b) IC anion analysis of the sump solids and slurry solids indicated all of the species were less than detection limits. (c) Radionuclide analysis of the sump solids also indicated that most of the analytes were either at or below the detection limits. (d) Organic analysis of the sump solids and slurry solids indicated all of the species were less than detection limits. It should be noted that the results of this study may not be representative of future decon frit solutions or sump/slurry solids samples. Therefore, future DWPF decisions regarding the possible disposal pathways for either the aqueous or solid portions of the Decon Frit system need to factor in the potential differences. More specifically, introduction of a different frit or changes to other DWPF flowsheet unit operations (e.g., different sludge batch or coupling with other process streams) may impact not only the results but also the conclusions regarding acceptability with respect to the ETF WAC limits or other alternative disposal options.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raszewski, F; Tommy Edwards, T; David Peeler, D

Sludge Batch 4 (SB4) is currently being processed in the Defense Waste Processing Facility (DWPF) using Frit 510. The slurry pumps in Tank 40 are experiencing in-leakage of bearing water, which is causing the sludge slurry feed in Tank 40 to become dilute at a rapid rate. Currently, the DWPF is removing this dilution water by performing caustic boiling during the Sludge Receipt and Adjustment Tank (SRAT) cycle. In order to alleviate prolonged SRAT cycle times that may eventually impact canister production rates, decant scenarios of 100, 150, and 200 kilogallons of supernate were proposed for Tank 40 during themore » DWPF March outage. Based on the results of the preliminary assessment issued by the Savannah River National Laboratory (SRNL), the Liquid Waste Organization (LWO) issued a Technical Task Request (TTR) for SRNL to (1) perform a more detailed evaluation using updated SB4 compositional information and (2) assess the viability of Frit 510 and determine any potential impacts on the SB4 system. As defined in the TTR, LWO requested that SRNL validate the sludge--only SB4 flowsheet and the coupled operations flowsheet using the 100K gallon decant volume as well as the addition of 3 wt% sodium on a calcined oxide basis. Approximately 12 historical glasses were identified during a search of the ComProTM database that are located within at least one of the five glass regions defined by the proposed SB4 flowsheet options. While these glasses meet the requirements of a variability study there was some concern that the compositional coverage did not adequately bound all cases. Therefore, SRNL recommended that a supplemental experimental variability study be performed to support the various SB4 flowsheet options that may be implemented for future SB4 operations in DWPF. Eighteen glasses were selected based on nominal sludge projections representing the current as well as the proposed flowsheets over a WL interval of interest to DWPF (32-42%). The intent of the experimental portion of the variability study is to demonstrate that the glasses of the Frit 510-modified SB4 compositional region (Cases No.1-5) are both acceptable relative to the Environmental Assessment (EA) reference glass and predictable by the current DWPF process control models for durability. Frit 510 is a viable option for the processing of SB4 after a Tank 40 decant and the addition of products from the Actinide Removal Process (ARP). The addition of ARP did not have any negative impacts on the acceptability and predictability of the variability study glasses. The results of the variability study indicate that all of the study glasses (both quenched and centerline canister cooled (ccc)) have normalized releases for boron that are well below the reference EA glass (16.695 g/L). The durabilities of all of the study glasses are predictable using the current Product Composition Control System (PCCS) durability models with the exception of SB4VAR24ccc (Case No.2 at 41%). PCCS is not applicable to non-homogeneous glasses (i.e. glasses containing crystals such as acmite and nepheline), thus SB4VAR24ccc should not be predictable as it contains nepheline. The presence of nepheline has been confirmed in both SB4VAR13ccc and SB4VAR24ccc by X-ray diffraction (XRD). These two glasses are the first results which indicate that the current nepheline discriminator value of 0.62 is not conservative. The nepheline discriminator was implemented into PCCS for SB4 based on the fact that all of the historical glasses evaluated with nepheline values of 0.62 or greater did not contain nepheline via XRD analysis. Although these two glasses do cause some concern over the use of the 0.62 nepheline value for future DWPF glass systems, the impact to the current SB4 system is of little concern. More specifically, the formation of nepheline was observed in glasses targeting 41 or 42% WL. Current processing of the Frit 510-SB4 system in DWPF has nominally targeted 34% WL. For the SB4 variability study glasses targeting these lower WLs, nepheline formation was not observed and the minimal difference in PCT response between quenched and ccc versions supported its absence.« less

Five-month-old infants have expectations for the accumulation of nonsolid substances.

PubMed

Anderson, Erin M; Hespos, Susan J; Rips, Lance J

2018-06-01

Infants fail to represent quantities of non-cohesive substances in paradigms where they succeed with solid objects. Some investigators have interpreted these results as evidence that infants do not yet have representations for substances. More recent research, however, shows that 5-month-old infants expect objects and substances to behave and interact in different ways. In the present experiments, we test whether infants have expectations for substances when the outcomes are not simply the opposite of those for objects. In Experiment 1, we find that 5-month-old infants expect that when a cup of sand pours behind a screen, it will accumulate in just one pile rather than two. Similarly, infants expect that when two cups of sand pour in separate streams, two distinct piles will accumulate rather than one. Infants look significantly longer at outcomes with an inconsistent number of piles, providing evidence that infants have expectations for how sand accumulates. To test whether the number of cups or the number of pours guided expectations about accumulation, Experiment 2 placed these cues in conflict. This resulted in chance performance, suggesting that, for infants to build expectations about these outcomes, they need both cues (cup and pour) to converge. These findings offer insight into the nature of infants' representations for non-cohesive substances like sand. Copyright © 2018 Elsevier B.V. All rights reserved.

Results of Hg speciation testing on DWPF SMECT-4, SMECT-6, and RCT-2 samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.

2016-02-04

The Savannah River National Laboratory (SRNL) was tasked with preparing and shipping samples for Hg speciation by Eurofins Frontier Global Sciences, Inc. in Seattle, WA on behalf of the Savannah River Remediation (SRR) Mercury Task Team.i,ii The fifteenth shipment of samples was designated to include Defense Waste Processing Facility (DWPF) Slurry Mix Evaporator Condensate Tank (SMECT) samples from Sludge Receipt and Adjustment Tank (SRAT) Batch 738 and a Recycle Condensate Tank (RCT) sample from SRAT Batch 736. The DWPF sample designations for the three samples analyzed are provided in Table 1. The Batch 738 ‘Baseline’ SMECT sample was taken priormore » to Precipitate Reactor Feed Tank (PRFT) addition and concentration and therefore, precedes the SMECT-5 sample reported previously. iii The Batch 738 ‘End of SRAT Cycle’ SMECT sample was taken at the conclusion of SRAT operations for this batch (PRFT addition/concentration, acid additions, initial concentration, MCU addition, and steam stripping). Batch 738 experienced a sludge slurry carryover event, which introduced sludge solids to the SMECT that were particularly evident in the SMECT-5 sample, but less evident in the ‘End of SRAT Cycle’ SMECT-6 sample. The Batch 736 ‘After SME’ RCT sample was taken after completion of SMECT transfers at the end of the SME cycle.« less

EVALUATION OF ARG-1 SAMPLES PREPARED BY CESIUM CARBONATE DISSOLUTION DURING THE ISOLOK SME ACCEPTABILITY TESTING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.; Hera, K.; Coleman, C.

2011-12-05

Evaluation of Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. The Mechanical Systems & Custom Equipment Development (MS&CED) Section of the Savannah River National Laboratory (SRNL) recently completed the evaluation of one of these opportunities - the possibility of using an Isolok sampling valve as an alternative to the Hydragard valve for taking DWPF process samples at the Slurry Mix Evaporator (SME). The use of an Isolok for SME sampling has the potential to improve operability, reduce maintenance time, and decrease CPC cycle time. The SME acceptability testingmore » for the Isolok was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 and was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNLRP-2011-00145. RW-0333P QA requirements applied to the task, and the results from the investigation were documented in SRNL-STI-2011-00693. Measurement of the chemical composition of study samples was a critical component of the SME acceptability testing of the Isolok. A sampling and analytical plan supported the investigation with the analytical plan directing that the study samples be prepared by a cesium carbonate (Cs{sub 2}CO{sub 3}) fusion dissolution method and analyzed by Inductively Coupled Plasma - Optical Emission Spectroscopy (ICP-OES). The use of the cesium carbonate preparation method for the Isolok testing provided an opportunity for an additional assessment of this dissolution method, which is being investigated as a potential replacement for the two methods (i.e., sodium peroxide fusion and mixed acid dissolution) that have been used at the DWPF for the analysis of SME samples. Earlier testing of the Cs{sub 2}CO{sub 3} method yielded promising results which led to a TTR from Savannah River Remediation, LLC (SRR) to SRNL for additional support and an associated TTQAP to direct the SRNL efforts. A technical report resulting from this work was issued that recommended that the mixed acid method be replaced by the Cs{sub 2}CO{sub 3} method for the measurement of magnesium (Mg), sodium (Na), and zirconium (Zr) with additional testing of the method by DWPF Laboratory being needed before further implementation of the Cs{sub 2}CO{sub 3} method at that laboratory. While the SME acceptability testing of the Isolok does not address any of the open issues remaining after the publication of the recommendation for the replacement of the mixed acid method by the Cs{sub 2}CO{sub 3} method (since those issues are to be addressed by the DWPF Laboratory), the Cs{sub 2}CO{sub 3} testing associated with the Isolok testing does provide additional insight into the performance of the method as conducted by SRNL. The performance is to be investigated by looking to the composition measurement data generated by the samples of a standard glass, the Analytical Reference Glass - 1 (ARG-1), that were prepared by the Cs{sub 2}CO{sub 3} method and included in the SME acceptability testing of the Isolok. The measurements of these samples were presented as part of the study results, but no statistical analysis of these measurements was conducted as part of those results. It is the purpose of this report to provide that analysis, which was supported using JMP Version 7.0.2.« less

Organics Characterization Of DWPF Alternative Reductant Simulants, Glycolic Acid, And Antifoam 747

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, T. L.; Wiedenman, B. J.; Lambert, D. P.

The present study examines the fate of glycolic acid and other organics added in the Chemical Processing Cell (CPC) of the Defense Waste Processing Facility (DWPF) as part of the glycolic alternate flowsheet. Adoption of this flowsheet is expected to provide certain benefits in terms of a reduction in the processing time, a decrease in hydrogen generation, simplification of chemical storage and handling issues, and an improvement in the processing characteristics of the waste stream including an increase in the amount of nitrate allowed in the CPC process. Understanding the fate of organics in this flowsheet is imperative because tankmore » farm waste processed in the CPC is eventually immobilized by vitrification; thus, the type and amount of organics present in the melter feed may affect optimal melt processing and the quality of the final glass product as well as alter flammability calculations on the DWPF melter off gas. To evaluate the fate of the organic compounds added as the part of the glycolic flowsheet, mainly glycolic acid and antifoam 747, samples of simulated waste that was processed using the DWPF CPC protocol for tank farm sludge feed were generated and analyzed for organic compounds using a variety of analytical techniques at the Savannah River National Laboratory (SRNL). These techniques included Ion Chromatography (IC), Gas Chromatography-Mass Spectrometry (GC-MS), Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES), and Nuclear Magnetic Resonance (NMR) Spectroscopy. A set of samples were also sent to the Catholic University of America Vitreous State Laboratory (VSL) for analysis by NMR Spectroscopy at the University of Maryland, College Park. Analytical methods developed and executed at SRNL collectively showed that glycolic acid was the most prevalent organic compound in the supernatants of Slurry Mix Evaporator (SME) products examined. Furthermore, the studies suggested that commercially available glycolic acid contained minor amounts of impurities such as formic and diglycolic acid that were then carried over in the SME products. Oxalic acid present in the simulated tank farm waste was also detected. Finally, numerous other compounds, at low concentrations, were observed present in etheric extracts of aqueous supernate solutions of the SME samples and are thought to be breakdown products of antifoam 747. The data collectively suggest that although addition of glycolic acid and antifoam 747 will introduce a number of impurities and breakdown products into the melter feed, the concentrations of these organics is expected to remain low and may not significantly impact REDOX or off-gas flammability predictions. In the SME products examined presently, which contained variant amounts of glycolic acid and antifoam 747, no unexpected organic degradation product was found at concentrations above 500 mg/kg, a reasonable threshold concentration for an organic compound to be taken into account in the REDOX modeling. This statement does not include oxalic or formic acid that were sometimes observed above 500 mg/kg and acetic acid that has an analytical detection limit of 1250 mg/kg due to high glycolate concentration in the SME products tested. Once a finalized REDOX equation has been developed and implemented, REDOX properties of known organic species will be determined and their impact assessed. Although no immediate concerns arose during the study in terms of a negative impact of organics present in SME products of the glycolic flowsheet, evidence of antifoam degradation suggest that an alternative antifoam to antifoam 747 is worth considering. The determination and implementation of an antifoam that is more hydrolysis resistant would have benefits such as increasing its effectiveness over time and reducing the generation of degradation products.« less

YIELD STRESS REDUCTION OF DWPF MELTER FEED SLURRIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M; Michael02 Smith, M

2006-12-28

The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides (primarily iron, aluminum, magnesium, manganese, and uranium) and soluble sodium salts (carbonate, hydroxide, nitrite, nitrate, sulfate). The pretreatment process acidifies the sludge with nitric and formic acids, adds the glass formers as glass frit, then concentrates the resulting slurry to approximately 50 weight percent (wt%) total solids. This slurry is fed to the joule-heated melter where the remaining water is evaporated followedmore » by calcination of the solids and conversion to glass. The Savannah River National Laboratory (SRNL) is currently assisting DWPF efforts to increase throughput of the melter. As part of this effort, SRNL has investigated methods to increase the solids content of the melter feed to reduce the heat load required to complete the evaporation of water and allow more of the energy available to calcine and vitrify the waste. The process equipment in the facility is fixed and cannot process materials with high yield stresses, therefore increasing the solids content will require that the yield stress of the melter feed slurries be reduced. Changing the glass former added during pretreatment from an irregularly shaped glass frit to nearly spherical beads was evaluated. The evaluation required a systems approach which included evaluations of the effectiveness of beads in reducing the melter feed yield stress as well as evaluations of the processing impacts of changing the frit morphology. Processing impacts of beads include changing the settling rate of the glass former (which effects mixing and sampling of the melter feed slurry and the frit addition equipment) as well as impacts on the melt behavior due to decreased surface area of the beads versus frit. Beads were produced from the DWPF process frit by fire polishing. The frit was allowed to free fall through a flame, then quenched with a water spray. Approximately 90% of the frit was converted to beads by this process, as shown in Figure 1. Borosilicate beads of various diameters were also procured for initial testing.« less

Defense Waste Processing Facility Process Enhancements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bricker, Jonathan

2010-11-01

Jonathan Bricker provides an overview of process enhancements currently being done at the Defense Waste Processing Facility (DWPF) at SRS. Some of these enhancements include: melter bubblers; reduction in water use, and alternate reductant.

Impact of glycolate anion on aqueous corrosion in DWPF and downstream facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mickalonis, J. I.

2015-12-15

Glycolic acid is being evaluated as an alternate reductant in the preparation of high level waste for the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS). During processing, the glycolic acid may not be completely consumed with small quantities of the glycolate anion being carried forward to other high level waste (HLW) facilities. The impact of the glycolate anion on the corrosion of the materials of construction (MoC) throughout the waste processing system has not been previously evaluated. A literature review had revealed that corrosion data were not available for the MoCs in glycolic-bearing solutions applicable tomore » SRS systems. Data on the material compatibility with only glycolic acid or its derivative products were identified; however, data were limited for solutions containing glycolic acid or the glycolate anion.« less

Characterization Of The As-Received Sludge Batch 9 Qualification Sample (Htf-51-15-81)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J.

Savannah River National Laboratory (SRNL) personnel have been requested to qualify the next sludge batch (Sludge Batch 9 – SB9) for processing at the Defense Waste Processing Facility (DWPF). To accomplish this task, Savannah River Remediation (SRR) has sent SRNL a 3-L slurried sample of Tank 51H (HTF-51-15-81) to be characterized, washed, and then used in a lab-scale demonstration of the DWPF flowsheet (potentially after combining with Tank 40H sludge). This report documents the first steps of the qualification process – characterization of the as-received Tank 51H qualification sample. These results will be used to support a reprojection of SB9more » by SRR from which final Tank 51H washing, frit development, and Chemical Processing Cell (CPC) activities will be based.« less

Sludge batch 9 simulant runs using the nitric-glycolic acid flowsheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D. P.; Williams, M. S.; Brandenburg, C. H.

Testing was completed to develop a Sludge Batch 9 (SB9) nitric-glycolic acid chemical process flowsheet for the Defense Waste Processing Facility’s (DWPF) Chemical Process Cell (CPC). CPC simulations were completed using SB9 sludge simulant, Strip Effluent Feed Tank (SEFT) simulant and Precipitate Reactor Feed Tank (PRFT) simulant. Ten sludge-only Sludge Receipt and Adjustment Tank (SRAT) cycles and four SRAT/Slurry Mix Evaporator (SME) cycles, and one actual SB9 sludge (SRAT/SME cycle) were completed. As has been demonstrated in over 100 simulations, the replacement of formic acid with glycolic acid virtually eliminates the CPC’s largest flammability hazards, hydrogen and ammonia. Recommended processingmore » conditions are summarized in section 3.5.1. Testing demonstrated that the interim chemistry and Reduction/Oxidation (REDOX) equations are sufficient to predict the composition of DWPF SRAT product and SME product. Additional reports will finalize the chemistry and REDOX equations. Additional testing developed an antifoam strategy to minimize the hexamethyldisiloxane (HMDSO) peak at boiling, while controlling foam based on testing with simulant and actual waste. Implementation of the nitric-glycolic acid flowsheet in DWPF is recommended. This flowsheet not only eliminates the hydrogen and ammonia hazards but will lead to shorter processing times, higher elemental mercury recovery, and more concentrated SRAT and SME products. The steady pH profile is expected to provide flexibility in processing the high volume of strip effluent expected once the Salt Waste Processing Facility starts up.« less

Interim glycol flowsheet reduction/oxidation (redox) model for the Defense Waste Processing Facility (DWPF)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, C. M.; Williams, M. S.; Zamecnik, J. R.

Control of the REDuction/OXidation (REDOX) state of glasses containing high concentrations of transition metals, such as High Level Waste (HLW) glasses, is critical in order to eliminate processing difficulties caused by overly reduced or overly oxidized melts. Operation of a HLW melter at Fe +2/ΣFe ratios of between 0.09 and 0.33, a range which is not overly oxidizing or overly reducing, helps retain radionuclides in the melt, i.e. long-lived radioactive 99Tc species in the less volatile reduced Tc 4+ state, 104Ru in the melt as reduced Ru +4 state as insoluble RuO 2, and hazardous volatile Cr 6+ in themore » less soluble and less volatile Cr +3 state in the glass. The melter REDOX control balances the oxidants and reductants from the feed and from processing additives such as antifoam. Currently, the Defense Waste Processing Facility (DWPF) is running a formic acid-nitric acid (FN) flowsheet where formic acid is the main reductant and nitric acid is the main oxidant. During decomposition formate and formic acid releases H 2 gas which requires close control of the melter vapor space flammability. A switch to a nitric acid-glycolic acid (GN) flowsheet is desired as the glycolic acid flowsheet releases considerably less H 2 gas upon decomposition. This would greatly simplify DWPF processing. Development of an EE term for glycolic acid in the GN flowsheet is documented in this study.« less

PRELIMINARY EVALUATION OF DWPF IMPACTS OF BORIC ACID USE IN CESIUM STRIP FOR SWPF AND MCU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M.

2010-09-28

A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system includes the option to replace the current dilute nitric acid strip solution with boric acid. To support this effort, the impact of using 0.01M, 0.1M, 0.25M and 0.5M boric acid in place of 0.001M nitric acid was evaluated for impacts on the DWPF facility. The evaluation only covered the impacts of boric acid in the strip effluent and does not address the other changes in solvents (i.e., the new extractant, called MaxCalix,more » or the new suppressor, guanidine). Boric acid additions may lead to increased hydrogen generation during the SRAT and SME cycles as well as change the rheological properties of the feed. The boron in the strip effluent will impact glass composition and could require each SME batch to be trimmed with boric acid to account for any changes in the boron from strip effluent additions. Addition of boron with the strip effluent will require changes in the frit composition and could lead to changes in melt behavior. The severity of the impacts from the boric acid additions is dependent on the amount of boric acid added by the strip effluent. The use of 0.1M or higher concentrations of boric acid in the strip effluent was found to significantly impact DWPF operations while the impact of 0.01M boric acid is expected to be relatively minor. Experimental testing is required to resolve the issues identified during the preliminary evaluation. The issues to be addressed by the testing are: (1) Impact on SRAT acid addition and hydrogen generation; (2) Impact on melter feed rheology; (3) Impact on glass composition control; (4) Impact on frit production; and (5) Impact on melter offgas. A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system includes the option to replace the current dilute nitric acid strip solution with boric acid. To support this effort, the impact of using 0.01M, 0.1M, 0.25M and 0.5M boric acid in place of 0.001M nitric acid was evaluated for impacts on the DWPF facility. The evaluation only covered the impacts of boric acid in the strip effluent and does not address the other changes in solvents (i.e., the new extractant, called MaxCalix, or the new suppressor, guanidine). Experimental testing with the improved solvent is required to determine the impact of any changes in the entrained solvent on DWPF processing.« less

Solidification of Savannah River plant high level waste

NASA Astrophysics Data System (ADS)

Maher, R.; Shafranek, L. F.; Kelley, J. A.; Zeyfang, R. W.

1981-11-01

Authorization for construction of the Defense Waste Processing Facility (DWPF) is expected in FY-83. The optimum time for stage 2 authorization is about three years later. Detailed design and construction will require approximately five years for stage 1, with stage 2 construction completed about two to three years later. Production of canisters of waste glass would begin in 1988, and the existing backlog of high level waste sludge stored at SRP would be worked off by about the year 2000. Stage 2 operation could begin in 1990. The technology and engineering are ready for construction and eventual operation of the DWPF for immobilizing high level radioactive waste at Savannah River Plant (SRP). Proceeding with this project will provide the public, and the leadership of this country, with a crucial demonstration that a major quanitity of existing high level nuclear wastes can be safely and permanently immobilized.

Verification Of The Defense Waste Processing Facility's (DWPF) Process Digestion Methods For The Sludge Batch 8 Qualification Sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Click, D. R.; Edwards, T. B.; Wiedenman, B. J.

2013-03-18

This report contains the results and comparison of data generated from inductively coupled plasma – atomic emission spectroscopy (ICP-AES) analysis of Aqua Regia (AR), Sodium Peroxide/Sodium Hydroxide Fusion Dissolution (PF) and Cold Chem (CC) method digestions and Cold Vapor Atomic Absorption analysis of Hg digestions from the DWPF Hg digestion method of Sludge Batch 8 (SB8) Sludge Receipt and Adjustment Tank (SRAT) Receipt and SB8 SRAT Product samples. The SB8 SRAT Receipt and SB8 SRAT Product samples were prepared in the SRNL Shielded Cells, and the SRAT Receipt material is representative of the sludge that constitutes the SB8 Batch ormore » qualification composition. This is the sludge in Tank 51 that is to be transferred into Tank 40, which will contain the heel of Sludge Batch 7b (SB7b), to form the SB8 Blend composition.« less

Antifoam Degradation Products in Off Gas and Condensate of Sludge Batch 9 Simulant Nitric-Formic Flowsheet Testing for the Defense Waste Processing Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, T.

Ten chemical processing cell (CPC) experiments were performed using simulant to evaluate Sludge Batch 9 for sludge-only and coupled processing using the nitric-formic flowsheet in the Defense Waste Processing Facility (DWPF). Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) cycles were performed on eight of the ten. The other two were SRAT cycles only. Samples of the condensate, sludge, and off gas were taken to monitor the chemistry of the CPC experiments. The Savannah River National Laboratory (SRNL) has previously shown antifoam decomposes to form flammable organic products, (hexamethyldisiloxane (HMDSO), trimethylsilanol (TMS), and propanal), that are presentmore » in the vapor phase and condensate of the CPC vessels. To minimize antifoam degradation product formation, a new antifoam addition strategy was implemented at SRNL and DWPF to add antifoam undiluted.« less

The Kaye effect revisited: High speed imaging of leaping shampoo

NASA Astrophysics Data System (ADS)

Versluis, Michel; Blom, Cock; van der Meer, Devaraj; van der Weele, Ko; Lohse, Detlef

2003-11-01

When a visco-elastic fluid such as shampoo or shower gel is poured onto a flat surface the fluid piles up forming a heap on which rather irregular combinations of fluid buckling, coiling and folding are observed. Under specific conditions a string of fluid leaps from the heap and forms a steady jet fed by the incoming stream. Momentum transfer of the incoming jet, combined with the shear-thinning properties of the fluid, lead to a spoon-like dimple in the highly viscous fluid pool in which the jet recoils. The jet can be stable for several seconds. This effect is known as the Kaye effect. In order to reveal its mechanism we analyzed leaping shampoo through high-speed imaging. We studied the jet formation, jet stability and jet disruption mechanisms. We measured the velocity of both the incoming and recoiled jet, which was found to be thicker and slower. By inclining the surface on which the fluid was poured we observed jets leaping at upto five times.

Nucleation and crystal growth behavior of nepheline in simulated high-level waste glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K.; Amoroso, J.; Mcclane, D.

The Savannah River National Laboratory (SRNL) has been tasked with supporting glass formulation development and process control strategies in key technical areas, relevant to the Department of Energy’s Office of River Protection (DOE-ORP) and related to high-level waste (HLW) vitrification at the Waste Treatment and Immobilization Plant (WTP). Of specific interest is the development of predictive models for crystallization of nepheline (NaAlSiO4) in HLW glasses formulated at high alumina concentrations. This report summarizes recent progress by researchers at SRNL towards developing a predicative tool for quantifying nepheline crystallization in HLW glass canisters using laboratory experiments. In this work, differential scanningmore » calorimetry (DSC) was used to obtain the temperature regions over which nucleation and growth of nepheline occur in three simulated HLW glasses - two glasses representative of WTP projections and one glass representative of the Defense Waste Processing Facility (DWPF) product. The DWPF glass, which has been studied previously, was chosen as a reference composition and for comparison purposes. Complementary quantitative X-ray diffraction (XRD) and optical microscopy confirmed the validity of the methodology to determine nucleation and growth behavior as a function of temperature. The nepheline crystallization growth region was determined to generally extend from ~ 500 to >850 °C, with the maximum growth rates occurring between 600 and 700 °C. For select WTP glass compositions (high Al2O3 and B2O3), the nucleation range extended from ~ 450 to 600 °C, with the maximum nucleation rates occurring at ~ 530 °C. For the DWPF glass composition, the nucleation range extended from ~ 450 to 750 °C with the maximum nucleation rate occurring at ~ 640 °C. The nepheline growth at the peak temperature, as determined by XRD, was between 35 - 75 wt.% /hour. A maximum nepheline growth rate of ~ 0.1 mm/hour at 700 °C was measured for the DWPF composition using optical microscopy. This research establishes a viable alternative to more traditional techniques for evaluating nepheline crystallization in large numbers of glasses, which are prohibitively time consuming or otherwise impractical. The ultimate objective is to combine the nucleation and growth information obtained from DSC, like that presented in this report, with computer simulations of glass cooling within the canister to accurately predict nepheline crystallization in HLW during processing through WTP.« less

SLUDGE BATCH 7B QUALIFICATION ACTIVITIES WITH SRS TANK FARM SLUDGE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J.; Click, D.; Lambert, D.

2011-11-16

Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry - Sludge Batch 7b (SB7b) - be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from Hmore » Canyon are often added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL typically simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). With the tight schedule constraints for SB7b and the potential need for caustic addition to allow for an acceptable glass processing window, the qualification for SB7b was approached differently than past batches. For SB7b, SRNL prepared a Tank 51 and a Tank 40 sample for qualification. SRNL did not receive the qualification sample from Tank 51 nor did it simulate all of the Tank Farm washing and decanting operations. Instead, SRNL prepared a Tank 51 SB7b sample from samples of Tank 7 and Tank 51, along with a wash solution to adjust the supernatant composition to the final SB7b Tank 51 Tank Farm projections. SRNL then prepared a sample to represent SB7b in Tank 40 by combining portions of the SRNL-prepared Tank 51 SB7b sample and a Tank 40 Sludge Batch 7a (SB7a) sample. The blended sample was 71% Tank 40 (SB7a) and 29% Tank 7/Tank 51 on an insoluble solids basis. This sample is referred to as the SB7b Qualification Sample. The blend represented the highest projected Tank 40 heel (as of May 25, 2011), and thus, the highest projected noble metals content for SB7b. Characterization was performed on the Tank 51 SB7b samples and SRNL performed DWPF simulations using the Tank 40 SB7b material. This report documents: (1) The preparation and characterization of the Tank 51 SB7b and Tank 40 SB7b samples. (2) The performance of a DWPF Chemical Process Cell (CPC) simulation using the SB7b Tank 40 sample. The simulation included a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid was added to the sludge to destroy nitrite and reduce mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit was added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters were based on work with a nonradioactive simulant. (3) Vitrification of a portion of the SME product and characterization and durability testing (as measured by the Product Consistency Test (PCT)) of the resulting glass. (4) Rheology measurements of the SRAT receipt, SRAT product, and SME product. This program was controlled by a Task Technical and Quality Assurance Plan (TTQAP), and analyses were guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R&D) for the DWPF. It should be noted that much of the data in this document has been published in interoffice memoranda. The intent of this technical report is bring all of the SB7b related data together in a single permanent record and to discuss the overall aspects of SB7b processing.« less

A procedure for estimating Bacillus cereus spores in soil and stream-sediment samples - A potential exploration technique

USGS Publications Warehouse

Watterson, J.R.

1985-01-01

The presence of bacterial spores of the Bacillus cereus group in soils and stream sediments appears to be a sensitive indicator of several types of concealed mineral deposits, including vein-type gold deposits. The B. cereus assay is rapid, inexpensive, and inherently reproducible. The test, currently under investigation for its potential in mineral exploration, is recommended for use on a research basis. Among the aerobic spore-forming bacilli, only B. cereus and closely related strains produce an opaque zone in egg-yolk emulsion agar. This characteristic, also known as the Nagler of lecitho-vitellin reaction, has long been used to rapidly indentify and estimate presumptive B. cereus. The test is here adapted to permit rapid estimation of B. cereus spores in soil and stream-sediment samples. Relative standard deviation was 10.3% on counts obtained from two 40-replicate pour-plate determinations. As many as 40 samples per day can be processed. Enough procedural detail is included to permit investigation of the test in conventional geochemical laboratories using standard microbiological safety precautions. ?? 1985.

Phase 2 Report--Mercury Behavior In The Defense Waste Processing Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C.; Fellinger, T.

2016-07-27

The purpose of this report is to provide a summary of the DWPF processing history in regards to mercury, document the mercury results obtained on the product and condensate samples, and provide further recommendations based on the data obtained.

Characterization of the SRNL-Washed tank 51 sludge batch 9 qualification sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J. M.

2016-01-01

Savannah River National Laboratory (SRNL) personnel have been requested to qualify the next sludge batch (Sludge Batch 9 – SB9) for processing at the Defense Waste Processing Facility (DWPF). To accomplish this task, Savannah River Remediation (SRR) sent SRNL a 3-L sample of Tank 51H slurry to be characterized, washed, and then used in a lab-scale demonstration of the DWPF flowsheet (after combining with Tank 40H sludge). SRNL has washed the Tank 51H sample per the Tank Farm washing strategy as of October 20, 2015. A part of the qualification process is extensive radionuclide and chemical characterization of the SRNL-washedmore » Tank 51H slurry. This report documents the chemical characterization of the washed slurry; radiological characterization is in progress and will be documented in a separate report. The analytical results of this characterization are comparable to the Tank Farm projections. Therefore, it is recommended that SRNL use this washed slurry for the ongoing SB9 qualification activities.« less

Polymeric compositions and their method of manufacture. [forming filled polymer systems using cryogenics

NASA Technical Reports Server (NTRS)

Moser, B. G.; Landel, R. F. (Inventor)

1972-01-01

Filled polymer compositions are made by dissolving the polymer binder in a suitable sublimable solvent, mixing the filler material with the polymer and its solvent, freezing the resultant mixture, and subliming the frozen solvent from the mixture from which it is then removed. The remaining composition is suitable for conventional processing such as compression molding or extruding. A particular feature of the method of manufacture is pouring the mixed solution slowly in a continuous stream into a cryogenic bath wherein frozen particles of the mixture result. The frozen individual particles are then subjected to the sublimation.

High Integrity Castings: Proceedings of the Conference on Advances in High Integrity Castings Held in Conjunction with the 1988 World Materials Congress, Chicago, Illinois, USA, 24-30 September 1988

DTIC Science & Technology

1988-01-01

above design requirements. The The first cast parts used in this higher strength standard chemistry parts application were of the Extra Low...present work was to study the use of beta THE HIGH COST OF TITANIUM alloys can limit their titanium alloys in the cast form. Beta or use to applications ...refractory as was is intended to achieve a pouring stream su- used with the nozzles for steel applications . perior to conventional nozzle designs , and this

TANK 40 FINAL SB7B CHEMICAL CHARACTERIZATION RESULTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C.

2012-03-15

A sample of Sludge Batch 7b (SB7b) was taken from Tank 40 in order to obtain radionuclide inventory analyses necessary for compliance with the Waste Acceptance Product Specifications (WAPS). The SB7b WAPS sample was also analyzed for chemical composition including noble metals and fissile constituents, and these results are reported here. These analyses along with the WAPS radionuclide analyses will help define the composition of the sludge in Tank 40 that is currently being fed to the Defense Waste Processing Facility (DWPF) as SB7b. At the Savannah River National Laboratory (SRNL) the 3-L Tank 40 SB7b sample was transferred frommore » the shipping container into a 4-L high density polyethylene bottle and solids were allowed to settle over the weekend. Supernate was then siphoned off and circulated through the shipping container to complete the transfer of the sample. Following thorough mixing of the 3-L sample, a 558 g sub-sample was removed. This sub-sample was then utilized for all subsequent analytical samples. Eight separate aliquots of the slurry were digested, four with HNO{sub 3}/HCl (aqua regia) in sealed Teflon{reg_sign} vessels and four with NaOH/Na{sub 2}O{sub 2} (alkali or peroxide fusion) using Zr crucibles. Two Analytical Reference Glass - 1 (ARG-1) standards were digested along with a blank for each preparation. Each aqua regia digestion and blank was diluted to 1:100 mL with deionized water and submitted to Analytical Development (AD) for inductively coupled plasma - atomic emission spectroscopy (ICP-AES) analysis, inductively coupled plasma - mass spectrometry (ICP-MS) analysis, atomic absorption spectroscopy (AA) for As and Se, and cold vapor atomic absorption spectroscopy (CV-AA) for Hg. Equivalent dilutions of the alkali fusion digestions and blank were submitted to AD for ICP-AES analysis. Tank 40 SB7b supernate was collected from a mixed slurry sample in the SRNL Shielded Cells and submitted to AD for ICP-AES, ion chromatography (IC), total base/free OH{sup -}/other base, total inorganic carbon/total organic carbon (TIC/TOC) analyses, and Cs-137 gamma scan. Weighted dilutions of slurry were submitted for IC, TIC/TOC, and total base/free OH{sup -}/other base analyses. Activities for U-233, U-235, and Pu-239 were determined from the ICP-MS data for the aqua regia digestions of the Tank 40 WAPS slurry using the specific activity of each isotope. The Pu-241 value was determined from a Pu-238/-241 method developed by SRNL AD and previously described. The following conclusions were drawn from the analytical results reported here: (1) The ratios of the major elements for the SB7b WAPS sample are different from those measured for the SB7a WAPS sample. There is less Al and Mn relative to Fe than the previous sludge batch. (2) The elemental composition of this sample and the analyses conducted here are reasonable and consistent with DWPF batch data measurements in light of DWPF pre-sample concentration and SRAT product heel contributions to the DWPF SRAT receipt analyses. The element ratios for Al/Fe, Ca/Fe, Mn/Fe, and U/Fe agree within 10% between this work and the DWPF Sludge Receipt and Adjustment Tank (SRAT) receipt analyses. (3) Sulfur in the SB7b WAPS sample is 82% soluble, slightly less than results reported for SB3, SB4, and SB6 samples but unlike the 50% insoluble sulfur observed in the SB5 WAPS sample. In addition, 23% of the soluble sulfur is not present as sulfate in SB7b. (4) The average activities of the fissile isotopes of interest in the SB7b WAPS sample are (in {mu}Ci/g of total dried solids): 4.22E-02 U-233, 6.12E-04 U-235, 1.08E+01 Pu-239, and 5.09E+01 Pu-241. The full radionuclide composition will be reported in a future document. (5) The fission product noble metal and Ag concentrations appear to have largely peaked in previous DWPF sludge batches, with the exception of Ru, which still shows a slight increase in SB7b.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D.; Edwards, T.

High-level waste (HLW) throughput (i.e., the amount of waste processed per unit of time) is primarily a function of two critical parameters: waste loading (WL) and melt rate. For the Defense Waste Processing Facility (DWPF), increasing HLW throughput would significantly reduce the overall mission life cycle costs for the Department of Energy (DOE). Significant increases in waste throughput have been achieved at DWPF since initial radioactive operations began in 1996. Key technical and operational initiatives that supported increased waste throughput included improvements in facility attainment, the Chemical Processing Cell (CPC) flowsheet, process control models and frit formulations. As a resultmore » of these key initiatives, DWPF increased WLs from a nominal 28% for Sludge Batch 2 (SB2) to {approx}34 to 38% for SB3 through SB6 while maintaining or slightly improving canister fill times. Although considerable improvements in waste throughput have been obtained, future contractual waste loading targets are nominally 40%, while canister production rates are also expected to increase (to a rate of 325 to 400 canisters per year). Although implementation of bubblers have made a positive impact on increasing melt rate for recent sludge batches targeting WLs in the mid30s, higher WLs will ultimately make the feeds to DWPF more challenging to process. Savannah River Remediation (SRR) recently requested the Savannah River National Laboratory (SRNL) to perform a paper study assessment using future sludge projections to evaluate whether the current Process Composition Control System (PCCS) algorithms would provide projected operating windows to allow future contractual WL targets to be met. More specifically, the objective of this study was to evaluate future sludge batch projections (based on Revision 16 of the HLW Systems Plan) with respect to projected operating windows using current PCCS models and associated constraints. Based on the assessments, the waste loading interval over which a glass system (i.e., a projected sludge composition with a candidate frit) is predicted to be acceptable can be defined (i.e., the projected operating window) which will provide insight into the ability to meet future contractual WL obligations. In this study, future contractual WL obligations are assumed to be 40%, which is the goal after all flowsheet enhancements have been implemented to support DWPF operations. For a system to be considered acceptable, candidate frits must be identified that provide access to at least 40% WL while accounting for potential variation in the sludge resulting from differences in batch-to-batch transfers into the Sludge Receipt and Adjustment Tank (SRAT) and/or analytical uncertainties. In more general terms, this study will assess whether or not the current glass formulation strategy (based on the use of the Nominal and Variation Stage assessments) and current PCCS models will allow access to compositional regions required to targeted higher WLs for future operations. Some of the key questions to be considered in this study include: (1) If higher WLs are attainable with current process control models, are the models valid in these compositional regions? If the higher WL glass regions are outside current model development or validation ranges, is there existing data that could be used to demonstrate model applicability (or lack thereof)? If not, experimental data may be required to revise current models or serve as validation data with the existing models. (2) Are there compositional trends in frit space that are required by the PCCS models to obtain access to these higher WLs? If so, are there potential issues with the compositions of the associated frits (e.g., limitations on the B{sub 2}O{sub 3} and/or Li{sub 2}O concentrations) as they are compared to model development/validation ranges or to the term 'borosilicate' glass? If limitations on the frit compositional range are realized, what is the impact of these restrictions on other glass properties such as the ability to suppress nepheline formation or influence melt rate? The model based assessments being performed make the assumption that the process control models are applicable over the glass compositional regions being evaluated. Although the glass compositional region of interest is ultimately defined by the specific frit, sludge, and WL interval used, there is no prescreening of these compositional regions with respect to the model development or validation ranges which is consistent with current DWPF operations.« less

Optimal placement of off-stream water sources for ephemeral stream recovery

USGS Publications Warehouse

Rigge, Matthew B.; Smart, Alexander; Wylie, Bruce

2013-01-01

Uneven and/or inefficient livestock distribution is often a product of an inadequate number and distribution of watering points. Placement of off-stream water practices (OSWP) in pastures is a key consideration in rangeland management plans and is critical to achieving riparian recovery by improving grazing evenness, while improving livestock performance. Effective OSWP placement also minimizes the impacts of livestock use radiating from OSWP, known as the “piosphere.” The objective of this study was to provide land managers with recommendations for the optimum placement of OSWP. Specifically, we aimed to provide minimum offset distances of OSWP to streams and assess the effective range of OSWP using Normalized Difference Vegetation Index (NDVI) values, an indicator of live standing crop. NDVI values were determined from a time-series of Satellite Pour l'Observation de la Terre (SPOT) 20-m images of western South Dakota mixed-grass prairie. The NDVI values in ephemeral stream channels (in-channel) and uplands were extracted from pre- and post-OSWP images taken in 1989 and 2010, respectively. NDVI values were normalized to a reference imagine and subsequently by ecological site to produce nNDVI. Our results demonstrate a significant (P 2 = 0.49, P = 0.05) and increased with average distance to OSWP in a pasture (R2 = 0.43, P = 0.07). Piospheric reduction in nNDVI was observed within 200 m of OSWP, occasionally overlapping in-channel areas. The findings of this study suggest placement of OSWP 200 to 1 250 m from streams to achieve optimal results. These results can be used to increase grazing efficiency by effectively placing OSWP and insure that piospheres do not overlap ecologically important in-channel areas.

CHARACTERIZATION OF A PRECIPITATE REACTOR FEED TANK (PRFT) SAMPLE FROM THE DEFENSE WASTE PROCESSING FACILITY (DWPF)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.; Bannochie, C.

2014-05-12

A sample of from the Defense Waste Processing Facility (DWPF) Precipitate Reactor Feed Tank (PRFT) was pulled and sent to the Savannah River National Laboratory (SRNL) in June of 2013. The PRFT in DWPF receives Actinide Removal Process (ARP)/ Monosodium Titanate (MST) material from the 512-S Facility via the 511-S Facility. This 2.2 L sample was to be used in small-scale DWPF chemical process cell testing in the Shielded Cells Facility of SRNL. A 1L sub-sample portion was characterized to determine the physical properties such as weight percent solids, density, particle size distribution and crystalline phase identification. Further chemical analysismore » of the PRFT filtrate and dissolved slurry included metals and anions as well as carbon and base analysis. This technical report describes the characterization and analysis of the PRFT sample from DWPF. At SRNL, the 2.2 L PRFT sample was composited from eleven separate samples received from DWPF. The visible solids were observed to be relatively quick settling which allowed for the rinsing of the original shipping vials with PRFT supernate on the same day as compositing. Most analyses were performed in triplicate except for particle size distribution (PSD), X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and thermogravimetric analysis (TGA). PRFT slurry samples were dissolved using a mixed HNO3/HF acid for subsequent Inductively Coupled Plasma Atomic Emission Spectroscopy (ICPAES) and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) analyses performed by SRNL Analytical Development (AD). Per the task request for this work, analysis of the PRFT slurry and filtrate for metals, anions, carbon and base were primarily performed to support the planned chemical process cell testing and to provide additional component concentrations in addition to the limited data available from DWPF. Analysis of the insoluble solids portion of the PRFT slurry was aimed at detailed characterization of these solids (TGA, PSD, XRD and SEM) in support of the Salt IPT chemistry team. The overall conclusions from analyses performed in this study are that the PRFT slurry consists of 0.61 Wt.% insoluble MST solids suspended in a 0.77 M [Na+] caustic solution containing various anions such as nitrate, nitrite, sulfate, carbonate and oxalate. The corresponding measured sulfur level in the PRFT slurry, a critical element for determining how much of the PRFT slurry gets blended into the SRAT, is 0.437 Wt.% TS. The PRFT slurry does not contain insoluble oxalates nor significant quantities of high activity sludge solids. The lack of sludge solids has been alluded to by the Salt IPT chemistry team in citing that the mixing pump has been removed from Tank 49H, the feed tank to ARP-MCU, thus allowing the sludge solids to settle out. The PRFT aqueous slurry from DWPF was found to contain 5.96 Wt.% total dried solids. Of these total dried solids, relatively low levels of insoluble solids (0.61 Wt.%) were measured. The densities of both the filtrate and slurry were 1.05 g/mL. Particle size distribution of the PRFT solids in filtered caustic simulant and XRD analysis of washed/dried PRFT solids indicate that the PRFT slurry contains a bimodal distribution of particles in the range of 1 and 6 μm and that the particles contain sodium titanium oxide hydroxide Na2Ti2O4(OH)2 crystalline material as determined by XRD. These data are in excellent agreement with similar data obtained from laboratory sampling of vendor supplied MST. Scanning Electron Microscopy (SEM) combined with Energy Dispersive X-ray Spectroscopy (EDS) analysis of washed/dried PRFT solids shows the particles to be like previous MST analyses consisting of irregular shaped micron-sized solids consisting primarily of Na and Ti. Thermogravimetric analysis of the washed and unwashed PRFT solids shows that the washed solids are very similar to MST solids. The TGA mass loss signal for the unwashed solids shows similar features to TGA performed on cellulose nitrate filter paper indicating significant presence of the deteriorated filter in this unwashed sample. Neither the washed nor unwashed PRFT solids TGA traces showed any features that would indicate presence of sodium oxalate solids. The PRFT Filtrate elemental analysis shows that Na, S and Al are major soluble species with trace levels of B, Cr, Cu, K, Li, Si, Tc, Th and U present. Nitrate, nitrite, sulfate, oxalate, carbonate and hydroxide are major soluble anion species. There is good agreement between the analyzed TOC and the total carbon calculated from the sum of oxalate and minor species formate. Comparison of the amount and speciation of the carbon species between filtrate and slurry indicates no significant carbon-containing species, e.g., sodium oxalate, are present in the slurry solids. Dissolution of the PRFT slurry and subsequent analysis shows that Na, Ti, Si and U are the major elements present on a Wt.% total dried solids basis with 30, 5.8 and 0.47 and 0.11 Wt.% total dried solids, respectively. The amount of Al in the dissolved PRFT slurry is less than that calculated from the PRFT filtrate alone which suggests that the mixed acid digestion used in this work is not optimized for Al recovery. The concentrations of Ca, Fe, Hg and U are all low (at or below 0.11 wt%) and there is no detectable Mn or Ni present which indicates no significant HLW sludge solids are present in the PRFT slurry sample.« less

DEVELOPMENT OF AN ANTIFOAM TRACKING SYSTEM AS AN OPTION TO SUPPORT THE MELTER OFF-GAS FLAMMABILITY CONTROL STRATEGY AT THE DWPF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, T.; Lambert, D.

The Savannah River National Laboratory (SRNL) has been working with the Savannah River Remediation (SRR) Defense Waste Processing Facility (DWPF) in the development and implementation of an additional strategy for confidently satisfying the flammability controls for DWPF’s melter operation. An initial strategy for implementing the operational constraints associated with flammability control in DWPF was based upon an analytically determined carbon concentration from antifoam. Due to the conservative error structure associated with the analytical approach, its implementation has significantly reduced the operating window for processing and has led to recurrent Slurry Mix Evaporator (SME) and Melter Feed Tank (MFT) remediation. Tomore » address the adverse operating impact of the current implementation strategy, SRR issued a Technical Task Request (TTR) to SRNL requesting the development and documentation of an alternate strategy for evaluating the carbon contribution from antifoam. The proposed strategy presented in this report was developed under the guidance of a Task Technical and Quality Assurance Plan (TTQAP) and involves calculating the carbon concentration from antifoam based upon the actual mass of antifoam added to the process assuming 100% retention. The mass of antifoam in the Additive Mix Feed Tank (AMFT), in the Sludge Receipt and Adjustment Tank (SRAT), and in the SME is tracked by mass balance as part of this strategy. As these quantities are monitored, the random and bias uncertainties affecting their values are also maintained and accounted for. This report documents: 1) the development of an alternate implementation strategy and associated equations describing the carbon concentration from antifoam in each SME batch derived from the actual amount of antifoam introduced into the AMFT, SRAT, and SME during the processing of the batch. 2) the equations and error structure for incorporating the proposed strategy into melter off-gas flammability assessments. Sample calculations of the system are also included in this report. Please note that the system developed and documented in this report is intended as an alternative to the current, analytically-driven system being utilized by DWPF; the proposed system is not intended to eliminate the current system. Also note that the system developed in this report to track antifoam mass in the AMFT, SRAT, and SME will be applicable beyond just Sludge Batch 8. While the model used to determine acceptability of the SME product with respect to melter off-gas flammability controls must be reassessed for each change in sludge batch, the antifoam mass tracking methodology is independent of sludge batch composition and as such will be transferable to future sludge batches.« less

Bubblers Speed Nuclear Waste Processing at SRS

ScienceCinema

None

2018-05-23

At the Department of Energy's Savannah River Site, American Recovery and Reinvestment Act funding has supported installation of bubbler technology and related enhancements in the Defense Waste Processing Facility (DWPF). The improvements will accelerate the processing of radioactive waste into a safe, stable form for storage and permit expedited closure of underground waste tanks holding 37 million gallons of liquid nuclear waste.

Analysis Of Condensate Samples In Support Of The Antifoam Degradation Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hay, M.; Martino, C.

2016-01-12

The degradation of Antifoam 747 to form flammable decomposition products has resulted in declaration of a Potential Inadequacy in the Safety Analysis (PISA) for the Defense Waste Processing Facility (DWPF). Savannah River National Laboratory (SRNL) testing with simulants showed that hexamethyldisiloxane (HMDSO), trimethylsilanol (TMS), and 1-propanal are formed in the offgas from the decomposition of the antifoam. A total of ten DWPF condensate samples from Batch 735 and 736 were analyzed by SRNL for three degradation products and additional analytes. All of the samples were analyzed to determine the concentrations of HMDSO, TMS, and propanal. The results of the organicmore » analysis found concentrations for propanal and HMDSO near or below the detection limits for the analysis. The TMS concentrations ranged from below detection to 11 mg/L. The samples from Batch 736 were also analyzed for formate and oxalate anions, total organic carbon, and aluminum, iron, manganese, and silicon. Most of the samples contained low levels of formate and therefore low levels of organic carbon. These two values for each sample show reasonable agreement in most cases. Low levels of all the metals (Al, Fe, Mn, and Si) were present in most of the samples.« less

ANALYSIS OF CONDENSATE SAMPLES IN SUPPORT OF THE ANTIFOAM DEGRADATION STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hay, M.; Martino, C.

2016-02-29

The degradation of Antifoam 747 to form flammable decomposition products has resulted in declaration of a Potential Inadequacy in the Safety Analysis (PISA) for the Defense Waste Processing Facility (DWPF). Savannah River National Laboratory (SRNL) testing with simulants showed that hexamethyldisiloxane (HMDSO), trimethylsilanol (TMS), and 1-propanal are formed in the offgas from the decomposition of the antifoam. A total of ten DWPF condensate samples from Batch 735 and 736 were analyzed by SRNL for three degradation products and additional analytes. All of the samples were analyzed to determine the concentrations of HMDSO, TMS, and propanal. The results of the organicmore » analysis found concentrations for propanal and HMDSO near or below the detection limits for the analysis. The TMS concentrations ranged from below detection to 11 mg/L. The samples from Batch 736 were also analyzed for formate and oxalate anions, total organic carbon, and aluminum, iron, manganese, and silicon. Most of the samples contained low levels of formate and therefore low levels of organic carbon. These two values for each sample show reasonable agreement in most cases. Low levels of all the metals (Al, Fe, Mn, and Si) were present in most of the samples.« less

New ArcGIS tools developed for stream network extraction and basin delineations using Python and java script

NASA Astrophysics Data System (ADS)

Omran, Adel; Dietrich, Schröder; Abouelmagd, Abdou; Michael, Märker

2016-09-01

Damages caused by flash floods hazards are an increasing phenomenon, especially in arid and semi-arid areas. Thus, the need to evaluate these areas based on their flash flood risk using maps and hydrological models is also becoming more important. For ungauged watersheds a tentative analysis can be carried out based on the geomorphometric characteristics of the terrain. To process regions with larger watersheds, where perhaps hundreds of watersheds have to be delineated, processed and classified, the overall process need to be automated. GIS packages such as ESRI's ArcGIS offer a number of sophisticated tools that help regarding such analysis. Yet there are still gaps and pitfalls that need to be considered if the tools are combined into a geoprocessing model to automate the complete assessment workflow. These gaps include issues such as i) assigning stream order according to Strahler theory, ii) calculating the threshold value for the stream network extraction, and iii) determining the pour points for each of the nodes of the Strahler ordered stream network. In this study a complete automated workflow based on ArcGIS Model Builder using standard tools will be introduced and discussed. Some additional tools have been implemented to complete the overall workflow. These tools have been programmed using Python and Java in the context of ArcObjects. The workflow has been applied to digital data from the southwestern Sinai Peninsula, Egypt. An optimum threshold value has been selected to optimize drainage configuration by statistically comparing all of the extracted stream configuration results from DEM with the available reference data from topographic maps. The code has succeeded in estimating the correct ranking of specific stream orders in an automatic manner without additional manual steps. As a result, the code has proven to save time and efforts; hence it's considered a very useful tool for processing large catchment basins.

In vitro dissolution of strontium titanate to estimate clearance rates in human lungs

NASA Astrophysics Data System (ADS)

Anderson, Jeri Lynn

At the In-Tank Precipitation facility (ITP) of the Savannah River Site, strontium and other radionuclides are removed from high-level radioactive waste and sent to the Defense Waste Processing Facility (DWPF). Strontium removal is accomplished by ion-exchange using monosodium titanate slurry which creates a form of strontium titanate with unknown solubility characteristics. In the case of accidental inhalation of a compound containing radioactive strontium, the ICRP, in Publication 66, recommends using default values for rates of absorption into body fluids at the lungs in the absence of reliable human or animal data. The default value depends on whether the absorption is considered to be fast, moderate, or slow (Type F, M, or S). Current dose assessment for an individual upon inadvertent exposure to airborne radioactive strontium assumes that all strontium compounds are Type F (soluble) or Type S (insoluble). Pure high-fired strontium titanate (SrTiOsb3) is considered Type S. The purpose of this project was to determine the solubility of strontium titanate in the form created at the ITP facility. An in vitro dissolution study was done with a precipitate simulant and with several types of strontium titanate and the results were compared. An in vivo study was also performed with high-fired SrTiOsb3 in rats. The data from both studies were used independently to assign the compounds to absorption type based on criteria specified in ICRP 71. Results of the in vitro studies showed that the DWPF simulant should be assigned to Type M and the strontium titanate should be assigned to Type S. It is possible the difference in the DWPF simulant is due to the other chemicals present. Results of the in vivo study verified that SrTiOsb3 should be assigned to Type S. Lung clearance data of SrTiOsb3 from rats showed that 85% cleared within the first 24 hours and the remaining 15% with a half-time of 130 days. The initial rapid clearance is attributed to deposition in airways as compared to the alveolar region.

Statistical Study to Evaluate the Effect of Processing Variables on Shrinkage Incidence During Solidification of Nodular Cast Irons

NASA Astrophysics Data System (ADS)

Gutiérrez, J. M.; Natxiondo, A.; Nieves, J.; Zabala, A.; Sertucha, J.

2017-04-01

The study of shrinkage incidence variations in nodular cast irons is an important aspect of manufacturing processes. These variations change the feeding requirements on castings and the optimization of risers' size is consequently affected when avoiding the formation of shrinkage defects. The effect of a number of processing variables on the shrinkage size has been studied using a layout specifically designed for this purpose. The β parameter has been defined as the relative volume reduction from the pouring temperature up to the room temperature. It is observed that shrinkage size and β decrease as effective carbon content increases and when inoculant is added in the pouring stream. A similar effect is found when the parameters selected from cooling curves show high graphite nucleation during solidification of cast irons for a given inoculation level. Pearson statistical analysis has been used to analyze the correlations among all involved variables and a group of Bayesian networks have been subsequently built so as to get the best accurate model for predicting β as a function of the input processing variables. The developed models can be used in foundry plants to study the shrinkage incidence variations in the manufacturing process and to optimize the related costs.

The concrete technology of post pouring zone of raft foundation of Hongyun Building B tower

NASA Astrophysics Data System (ADS)

Yin, Suhua; Yu, Liu; Wu, Yanli; Zhao, Ying

2017-08-01

The foundation of Hongyun building B tower is made of raft board foundation which is 3300mm in the thickness concreted pouring amount of large and the late poured band in the pouring settlement formed. The temperature of the pouring settlement was controlled in order to prevent the crack of the construction of the late poured band. The steel of post pouring band was designed and monitorred. The quality of post pouring band quality is guaranteed in the raft concrete foundation of Hongyun Building B tower.

Big drinkers: how BMI, gender and rules of thumb influence the free pouring of wine.

PubMed

Smarandescu, Laura; Walker, Doug; Wansink, Brian

2014-11-01

This research examines free pouring behavior and provides an account of how Body Mass Index (BMI) and gender might lead to the overpouring, and consequently the overconsumption of wine. An observational study with young adults investigated how BMI and gender affect free-pouring of wine over a variety of pouring scenarios, and how rules-of-thumb in pouring affect the quantities of alcohol poured by men and women across BMI categories. For men, the amount poured was positively related to BMI. However, BMI did not affect pours by women. The use of the "half glass" rule-of-thumb in pouring reduced the volume of wine poured by over 20% for both men and women. Importantly, this rule-of-thumb substantially attenuated the pours by men at high BMI levels. Increasing awareness of pouring biases represents an early and effective step toward curbing alcohol consumption among men, and especially those who are overweight. Additionally, using a simple "half glass" rule-of-thumb may be an effective way to curb overpouring, despite non-standard glass sizes. Copyright © 2014. Published by Elsevier B.V.

Results Of Hg Speciation Testing On DWPF SMECT-1, SMECT-3, And SMECT-5 Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C.

2016-01-07

The Savannah River National Laboratory (SRNL) was tasked with preparing and shipping samples for Hg speciation by Eurofins Frontier Global Sciences, Inc. in Seattle, WA on behalf of the Savannah River Remediation (SRR) Mercury Task Team. The thirteenth shipment of samples was designated to include Defense Waste Processing Facility (DWPF) Slurry Mix Evaporator Condensate Tank (SMECT) from Sludge Receipt and Adjustment Tank (SRAT) Batch 736 and 738 samples. Triplicate samples of each material were prepared for this shipment. Each replicate was analyzed for seven Hg species: total Hg, total soluble (dissolved) Hg, elemental Hg [Hg(0)], ionic (inorganic) Hg [Hg(I) andmore » Hg(II)], methyl Hg [CH 3Hg-X, where X is a counter anion], ethyl Hg [CH 3CH 2-Hg-X, where X is a counter anion], and dimethyl Hg [(CH 3) 2Hg]. The difference between the total Hg and total soluble Hg measurements gives the particulate Hg concentration, i.e. Hg adsorbed to the surface of particulate matter in the sample but without resolution of the specific adsorbed species. The average concentrations of Hg species in the aqueous samples derived from Eurofins reported data corrected for dilutions performed by SRNL are tabulated.« less

Inhibition Of Washed Sludge With Sodium Nitrite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J. W.; Lozier, J. S.

2012-09-25

This report describes the results of electrochemical tests used to determine the relationship between the concentration of the aggressive anions in washed sludge and the minimum effective inhibitor concentration. Sodium nitrate was added as the inhibitor because of its compatibility with the DWPF process. A minimum of 0.05M nitrite is required to inhibit the washed sludge simulant solution used in this study. When the worst case compositions and safety margins are considered, it is expected that a minimum operating limit of nearly 0.1M nitrite will be specified. The validity of this limit is dependent on the accuracy of the concentrationsmore » and solubility splits previously reported. Sodium nitrite additions to obtain 0.1M nitrite concentrations in washed sludge will necessitate the additional washing of washed precipitate in order to decrease its sodium nitrite inhibitor requirements sufficiently to remain below the sodium limits in the feed to the DWPF. Nitrite will be the controlling anion in "fresh" washed sludge unless the soluble chloride concentration is about ten times higher than predicted by the solubility splits. Inhibition of "aged" washed sludge will not be a problem unless significant chloride dissolution occurs during storage. It will be very important tomonitor the composition of washed sludge during processing and storage.« less

DWPF Melt Cell Crawler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, C.R.

2003-04-08

On December 2, 2002, Remote and Specialty Equipment Systems (RSES) of the Savannah River Technology Center (SRTC) was requested to build a remotely operated crawler to assist in cleaning the Defense Waste Processing Facility (DWPF) melt cell floor of glass, tools, and other debris. The crawler was to assist a grapple and vacuum system in cleaning the cell. The crawler was designed to push glass and debris into piles so that the grapple could pick up the material and place it in waste bins. The crawler was also designed to maneuver the end of the vacuum hose, if needed. Inmore » addition, the crawler was designed to clean the area beneath the cell worktable that was inaccessible to the grapple and vacuum system. Originally, the system was to be ready for deployment by December 17. The date was moved up to December 12 to better utilize the available time for clean up. The crawler was designed and built in 10 days and completed cleaning the melt cell in 8 days. Due to initial problems with the grapple and vacuum system, the crawler completed essentially all of the cleanup tasks by itself. The crawler also cleaned an area on the west side of the cell that was not initially slated for cleaning.« less

ANALYSIS OF 2H-EVAPORATOR SCALE WALL [HTF-13-82] AND POT BOTTOM [HTF-13-77] SAMPLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oji, L.

2013-06-21

Savannah River Remediation (SRR) is planning to remove a buildup of sodium aluminosilicate scale from the 2H-evaporator pot by loading and soaking the pot with heated 1.5 M nitric acid solution. Sampling and analysis of the scale material has been performed so that uranium and plutonium isotopic analysis can be input into a Nuclear Criticality Safety Assessment (NCSA) for scale removal by chemical cleaning. Historically, since the operation of the Defense Waste Processing Facility (DWPF), silicon in the DWPF recycle stream combines with aluminum in the typical tank farm supernate to form sodium aluminosilicate scale mineral deposits in the 2Hevaporatormore » pot and gravity drain line. The 2H-evaporator scale samples analyzed by Savannah River National Laboratory (SRNL) came from the bottom cone sections of the 2H-evaporator pot [Sample HTF-13-77] and the wall 2H-evaporator [sample HTF-13-82]. X-ray diffraction analysis (XRD) confirmed that both the 2H-evaporator pot scale and the wall samples consist of nitrated cancrinite (a crystalline sodium aluminosilicate solid) and clarkeite (a uranium oxy-hydroxide mineral). On “as received” basis, the bottom pot section scale sample contained an average of 2.59E+00 ± 1.40E-01 wt % total uranium with a U-235 enrichment of 6.12E-01 ± 1.48E-02 %, while the wall sample contained an average of 4.03E+00 ± 9.79E-01 wt % total uranium with a U-235 enrichment of 6.03E-01% ± 1.66E-02 wt %. The bottom pot section scale sample analyses results for Pu-238, Pu-239, and Pu-241 are 3.16E- 05 ± 5.40E-06 wt %, 3.28E-04 ± 1.45E-05 wt %, and <8.80E-07 wt %, respectively. The evaporator wall scale samples analysis values for Pu-238, Pu-239, and Pu-241 averages 3.74E-05 ± 6.01E-06 wt %, 4.38E-04 ± 5.08E-05 wt %, and <1.38E-06 wt %, respectively. The Pu-241 analyses results, as presented, are upper limit values. These results are provided so that SRR can calculate the equivalent uranium-235 concentrations for the NCSA. Results confirm that the uranium contained in the scale remains depleted with respect to natural uranium. SRNL did not calculate an equivalent U-235 enrichment, which takes into account other fissionable isotopes U-233, Pu-239 and Pu-241. The applicable method for calculation of equivalent U-235 will be determined in the NCSA.« less

DETERMINATION OF REPORTABLE RADIONUCLIDES FOR DWPF SLUDGE BATCH 7B (MACROBATCH 9)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C. L.; Diprete, D. P.

The Waste Acceptance Product Specifications (WAPS) 1.2 require that “The Producer shall report the inventory of radionuclides (in Curies) that have half-lives longer than 10 years and that are, or will be, present in concentrations greater than 0.05 percent of the total inventory for each waste type indexed to the years 2015 and 3115”. As part of the strategy to comply with WAPS 1.2, the Defense Waste Processing Facility (DWPF) will report for each waste type, all radionuclides (with half-lives greater than 10 years) that have concentrations greater than 0.01 percent of the total inventory from time of production throughmore » the 1100 year period from 2015 through 3115. The initial listing of radionuclides to be included is based on the design-basis glass as identified in the Waste Form Compliance Plan (WCP) and Waste Form Qualification Report (WQR). However, it is required that this list be expanded if other radionuclides with half-lives greater than 10 years are identified that may meet the greater than 0.01% criterion for Curie content. Specification 1.6 of the WAPS, International Atomic Energy Agency (IAEA) Safeguards Reporting for High Level Waste (HLW), requires that the ratio by weights of the following uranium and plutonium isotopes be reported: U-233, U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, and Pu- 242. Therefore, the complete set of reportable radionuclides must also include this set of U and Pu isotopes. The DWPF is receiving radioactive sludge slurry from HLW Tank 40. The radioactive sludge slurry in Tank 40 is a blend of the heel from Sludge Batch 7a (SB7a) and Sludge Batch 7b (SB7b) that was transferred to Tank 40 from Tank 51. The blend of sludge in Tank 40 is also referred to as Macrobatch 9 (MB9). This report develops the list of reportable radionuclides and associated activities as a function of time. The DWPF will use this list and the activities as one of the inputs for the development of the Production Records that relate to radionuclide inventory. This work was initiated through Technical Task Request (TTR) HLW-DWPF-TTR-2011-0004; Rev. 0 entitled Sludge Batch 7b Qualification Studies. Specifically, this report details results from performing Subtask II, Item 2 of the TTR and, in part, meets Deliverable 6 of the TTR. The work was performed following the Task Technical and Quality Assurance Plan (TTQAP), SRNL-RP-2011-00247, Rev. 0 and Analytical Study Plan (ASP), SRNL-RP-2011-00248, Rev. 0. In order to determine the reportable radionuclides for SB7b (MB9), a list of radioisotopes that may meet the criteria as specified by the Department of Energy’s (DOE) WAPS was developed. All radioactive U- 235 fission products and all radioactive activation products that could be in the SRS HLW were considered. In addition, all U and Pu isotopes identified in WAPS 1.6 were included in the list. This list was then evaluated and some isotopes were excluded from the projection calculations. Based on measurements and analytical detection limits, 27 radionuclides have been identified as reportable for DWPF SB7b as specified by WAPS 1.2. The WCP and WQR require that all of the radionuclides present in the Design Basis glass be considered as the initial set of reportable radionuclides. For SB7b, all of the radionuclides in the Design Basis glass are reportable except for three radionuclides: Pd-107, Cs-135, and Th-230. At no time during the 1100- year period between 2015 and 3115 did any of these three radionuclides contribute to more than 0.01% of the radioactivity on a Curie basis. Two additional uranium isotopes (U-235 and -236) must be added to the list of reportable radionuclides in order to meet WAPS 1.6. All of the Pu isotopes (Pu-238, -239, -240, -241, and -242) and other U isotopes (U-233, -234, and -238) identified in WAPS 1.6 were already determined to be reportable according to WAPS 1.2 This brings the total number of reportable radionuclides for SB7b to 29. The radionuclide measurements made for SB7b are similar to those performed in the previous SB7a MB8 work. Some method development/refinement occurred during the conduct of these measurements, leading to lower detection limits and more accurate measurement of some isotopes than was previously possible. Improvement in the analytical measurements will likely continue, and this in turn should lead to improved detection limit values for some radionuclides and actual measurements for still others.« less

Determination Of Reportable Radionuclides For DWPF Sludge Batch 7B (Macrobatch 9)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C. L.; DiPrete, D. P.

The Waste Acceptance Product Specifications (WAPS) 1.2 require that “The Producer shall report the inventory of radionuclides (in Curies) that have half-lives longer than 10 years and that are, or will be, present in concentrations greater than 0.05 percent of the total inventory for each waste type indexed to the years 2015 and 3115”. As part of the strategy to comply with WAPS 1.2, the Defense Waste Processing Facility (DWPF) will report for each waste type, all radionuclides (with half-lives greater than 10 years) that have concentrations greater than 0.01 percent of the total inventory from time of production throughmore » the 1100 year period from 2015 through 3115. The initial listing of radionuclides to be included is based on the design-basis glass as identified in the Waste Form Compliance Plan (WCP) and Waste Form Qualification Report (WQR). However, it is required that this list be expanded if other radionuclides with half-lives greater than 10 years are identified that may meet the greater than 0.01% criterion for Curie content. Specification 1.6 of the WAPS, International Atomic Energy Agency (IAEA) Safeguards Reporting for High Level Waste (HLW), requires that the ratio by weights of the following uranium and plutonium isotopes be reported: U-233, U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, and Pu-242. Therefore, the complete set of reportable radionuclides must also include this set of U and Pu isotopes. The DWPF is receiving radioactive sludge slurry from HLW Tank 40. The radioactive sludge slurry in Tank 40 is a blend of the heel from Sludge Batch 7a (SB7a) and Sludge Batch 7b (SB7b) that was transferred to Tank 40 from Tank 51. The blend of sludge in Tank 40 is also referred to as Macrobatch 9 (MB9). This report develops the list of reportable radionuclides and associated activities as a function of time. The DWPF will use this list and the activities as one of the inputs for the development of the Production Records that relate to radionuclide inventory. This work was initiated through Technical Task Request (TTR) HLW-DWPF-TTR-2011-0004; Rev. 0 entitled Sludge Batch 7b Qualification Studies. Specifically, this report details results from performing Subtask II, Item 2 of the TTR and, in part, meets Deliverable 6 of the TTR. The work was performed following the Task Technical and Quality Assurance Plan (TTQAP), SRNL-RP-2011-00247, Rev. 0 and Analytical Study Plan (ASP), SRNL-RP-2011-00248, Rev. 0. In order to determine the reportable radionuclides for SB7b (MB9), a list of radioisotopes that may meet the criteria as specified by the Department of Energy’s (DOE) WAPS was developed. All radioactive U-235 fission products and all radioactive activation products that could be in the SRS HLW were considered. In addition, all U and Pu isotopes identified in WAPS 1.6 were included in the list. This list was then evaluated and some isotopes were excluded from the projection calculations. Based on measurements and analytical detection limits, 27 radionuclides have been identified as reportable for DWPF SB7b as specified by WAPS 1.2. The WCP and WQR require that all of the radionuclides present in the Design Basis glass be considered as the initial set of reportable radionuclides. For SB7b, all of the radionuclides in the Design Basis glass are reportable except for three radionuclides: Pd-107, Cs-135, and Th-230. At no time during the 1100-year period between 2015 and 3115 did any of these three radionuclides contribute to more than 0.01% of the radioactivity on a Curie basis. Two additional uranium isotopes (U-235 and -236) must be added to the list of reportable radionuclides in order to meet WAPS 1.6. All of the Pu isotopes (Pu-238, -239, -240, -241, and -242) and other U isotopes (U-233, -234, and -238) identified in WAPS 1.6 were already determined to be reportable according to WAPS 1.2 This brings the total number of reportable radionuclides for SB7b to 29. The radionuclide measurements made for SB7b are similar to those performed in the previous SB7a MB8 work. Some method development/refinement occurred during the conduct of these measurements, leading to lower detection limits and more accurate measurement of some isotopes than was previously possible. Improvement in the analytical measurements will likely continue, and this in turn should lead to improved detection limit values for some radionuclides and actual measurements for still others.« less

Yield Stress Reduction of DWPF Melter Feed Slurries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M.E.; Smith, M.E.

2007-07-01

The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies High Level Waste for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. The HLW consists of insoluble metal hydroxides and soluble sodium salts. The pretreatment process acidifies the sludge with nitric and formic acids, adds the glass formers as glass frit, then concentrates the resulting slurry to approximately 50 weight percent (wt%) total solids. This slurry is fed to the joule-heated melter where the remaining water is evaporated followed by calcination of the solids and conversion to glass. The Savannah Rivermore » National Laboratory (SRNL) is currently assisting DWPF efforts to increase throughput of the melter. As part of this effort, SRNL has investigated methods to increase the solids content of the melter feed to reduce the heat load required to complete the evaporation of water and allow more of the energy available to calcine and vitrify the waste. The process equipment in the facility is fixed and cannot process materials with high yield stresses, therefore increasing the solids content will require that the yield stress of the melter feed slurries be reduced. Changing the glass former added during pretreatment from an irregularly shaped glass frit to nearly spherical beads was evaluated. The evaluation required a systems approach which included evaluations of the effectiveness of beads in reducing the melter feed yield stress as well as evaluations of the processing impacts of changing the frit morphology. Processing impacts of beads include changing the settling rate of the glass former (which effects mixing and sampling of the melter feed slurry and the frit addition equipment) as well as impacts on the melt behavior due to decreased surface area of the beads versus frit. Beads were produced from the DWPF process frit by fire polishing. The frit was allowed to free fall through a flame, then quenched with a water spray. Approximately 90% of the frit was converted to beads by this process. Yield stress reduction was measured by preparing melter feed slurries (using nonradioactive HLW simulants) that contain beads and comparing the yield stress with melter feed containing frit. A second set of tests was performed with beads of various diameters to determine if a decrease in diameter affected the results. Smaller particle size was shown to increase yield stress when frit is utilized. The settling rate of the beads was required to match the settling rate of the frit, therefore a decrease in particle size was anticipated. Settling tests were conducted in water, xanthan gum solutions, and in non-radioactive simulants of the HLW. The tests used time-lapse video-graphy as well as solids sampling to evaluate the settling characteristics of beads compared to frit of the same particle size. A preliminary melt rate evaluation was performed using a dry-fed Melt Rate Furnace (MRF) developed by SRNL. Preliminary evaluation of the impact of beading the frit on the frit addition system were completed by conducting flow loop testing. A recirculation loop was built with a total length of about 30 feet. Pump power, flow rate, outlet pressure, and observations of the flow in the horizontal upper section of the loop were noted. The recirculation flow was then gradually reduced and the above items recorded until settling was noted in the recirculation line. Overall, the data shows that the line pressure increased as the solids were increased for the same flow rate. In addition, the line pressure was higher for Frit 320 than the beads at the same solids level and flow. With the observations, a determination of minimum velocity to prevent settling could be done, but a graph of the line pressures versus velocity for the various tests was deemed to more objective. The graph shows that the inflection point in pressure drop is about the same for the beads and Frit 320. This indicates that the bead slurry would not require higher flows rates than frit slurry at DWPF during transfers. Another key finding was that the pump impeller was not significantly damaged by the bead slurry, while the Frit 320 slurry rapidly destroyed the impeller. Evidence of this was first observed when black particles were seen in the Frit 320 slurry being recirculated and then confirmed by a post-test inspection of the impeller. Finally, the pumping of bead slurry could be recovered even if flow is stopped. The Frit 320 slurry could not be restarted after stopping flow due to the nature of the frit to pack tightly when settled. Beads were shown to represent a significant process improvement versus frit for the DWPF process in lowering yield stress of the melter feed. Lower erosion of process equipment is another expected benefit.« less

Detecting channel riparian vegetation response to best-management-practices implementation in ephemeral streams with the use of spot high-resolution visible imagery

USGS Publications Warehouse

Kamp, Kendall Vande; Rigge, Matthew B.; Troelstrup, Nels H.; Smart, Alexander J.; Wylie, Bruce

2013-01-01

Heavily grazed riparian areas are commonly subject to channel incision, a lower water table, and reduced vegetation, resulting in sediment delivery above normal regimes. Riparian and in-channel vegetation functions as a roughness element and dissipates flow energy, maintaining stable channel geometry. Ash Creek, a tributary of the Bad River in western South Dakota contains a high proportion of incised channels, remnants of historically high grazing pressure. Best management practices (BMP), including off-stream watering sources and cross fencing, were implemented throughout the Bad River watershed during an Environmental Protection Agency (EPA) 319 effort to address high sediment loads. We monitored prairie cordgrass (Spartina pectinata Link) establishment within stream channels for 16 yr following BMP implementation. Photos were used to group stream reaches (n = 103) subjectively into three classes; absent (estimated  40% cover; n = 16) based on the relative amount of prairie cordgrass during 2010 assessments of ephemeral channels. Reaches containing drainage areas of 0.54 to 692 ha were delineated with the use of 2010 National Agriculture Imagery Program (NAIP) imagery. Normalized difference vegetation index (NDVI) values were extracted from 5 to 39 sample points proportional to reach length using a series of Satellite Pour l'Observation de la Terre (SPOT) satellite imagery. Normalized NDVI (nNDVI) of 2 152 sample points were determined from pre- and post-BMP images. Mean nNDVI values for each reach ranged from 0.33 to 1.77. ANOVA revealed significant increase in nNDVI in locations classified as present prairie cordgrass cover following BMP implementation. Establishment of prairie cordgrass following BMP implementation was successfully detected remotely. Riparian vegetation such as prairie cordgrass adds channel roughness that reduces the flow energy responsible for channel degradation.

Dependence of the pour point of diesel fuels on the properties of the initial components

NASA Technical Reports Server (NTRS)

Ostashov, V. M.; Bobrovskiy, S. A.

1979-01-01

An analytical expression is obtained for the dependence of the pour point of diesel fuels on the pour point and weight relationship of the initial components. For determining the pour point of a multicomponent fuel mixture, it is assumed that the mixture of two components has the pour point of a separate equivalent component, then calculating the pour point of this equivalent component mixed with a third component, etc.

Demonstration of Plasma Arc Environmental Technology Applications for the Demilitrization of DOD Stockpiles

NASA Technical Reports Server (NTRS)

Smith, Ed; Dee, P. E.; Zaghloul, Hany; Filius, Krag; Rivers, Tim

2000-01-01

Since 1989 the US Army Construction Engineering Research Laboratories (USACERL) have been active participants in the research and development towards establishing Plasma Arc Technology (PAT) as an efficient, economical, and safe hazardous waste immobilization tool. A plasma torch capable of generating high temperatures makes this technology a viable and powerful tool for the thermal destruction of various military industrial waste streams into an innocuous ceramic material no longer requiring hazardous waste landfill disposal. The emerging plasma environmental thermal treatment process has been used to safely and efficiently meet the waste disposal needs for various demilitarized components disposal needs, such as: (1) pyrotechnic smoke assemblies, (2) thermal batteries, (3) proximity fuses, (4) cartridge actuated devices (CADs), and (5) propellant actuated devices (PADs). MSE Technology Applications, Inc., (MSE) has proposed and fabricated a Mobile Plasma Treatment System to be a technology demonstrator for pilotscale mobile plasma waste processing. The system is capable of providing small-scale waste remediation services, and conducting waste stream applicability demonstrations. The Mobile Plasma Treatment System's innovative concept provides the flexibility to treat waste streams at numerous sites and sites with only a limited quantity of waste, yet too hazardous to transport to a regional fixed facility. The system was designed to be operated as skid mounted modules; consisting of a furnace module, controls module, offgas module, and ancillary systems module. All system components have been integrated to be operated from a single control station with both semi-continuous feeding and batch slag-pouring capability.

Demonstration of Plasma Arc Environmental Technology Applications for the Demilitarization of DOD Stockpiles

NASA Technical Reports Server (NTRS)

Smith, Ed; Zaghloul, Hany; Filius, Krag; Rivers, Tim

2000-01-01

Since 1989 the U.S. Army Construction Engineering Research Laboratories (USACERL) have been active participants in the research and development toward establishing Plasma Arc Technology (PAT) as an efficient, economical, and safe hazardous waste immobilization tool. A plasma torch capable of generating high temperatures makes this technology a viable and powerful tool for the thermal destruction of various military industrial waste streams into an innocuous ceramic material no longer requiring hazardous waste landfill (Class 1) disposal. The emerging pl asma environmental thermal treatment process, has been used to safely and efficiently meet the waste disposal needs for various demilitarized components disposal needs, such as: pyrotechnic smoke assemblies, thermal batteries, proximity fuses, cartridge actuated devices (CAD's), and propellant actuated devices (PAD's). MSE Technology Applications, Inc., (MSE) has proposed and fabricated a Mobile Plasma Treatment System to be a technology demonstrator for pilot-scale mobile plasma waste processing. The system is capable of providing small-scale waste remediation services, and conducting waste stream applicability demonstrations. The Mobile Plasma Treatment System's innovative concept provides the flexibility to treat waste streams at numerous sites and sites with only a limited quantity of waste, yet too hazardous to transport to a regional fixed facility. The system was designed to be operated as skid mounted modules; consisting of a furnace module, controls module, offgas module, and ancillary systems module. All system components have been integrated to be operated from a single control station with both semi-continuous feeding and batch slag-pouring capability.

Monitoring active volcanoes

USGS Publications Warehouse

Tilling, Robert I.

1987-01-01

One of the most spectacular, awesomely beautiful, and at times destructive displays of natural energy is an erupting volcano, belching fume and ash thousands of meters into the atmosphere and pouring out red-hot molten lava in fountains and streams. Countless eruptions in the geologic past have produced volcanic rocks that form much of the Earth's present surface. The gradual disintegration and weathering of these rocks have yielded some of the richest farmlands in the world, and these fertile soils play a significant role in sustaining our large and growing population. Were it not for volcanic activity, the Hawaiian Islands with their sugar cane and pineapple fields and magnificent landscapes and seascapes would not exist to support their residents and to charm their visitors. Yet, the actual eruptive processes are catastrophic and can claim life and property.

Implementation of flowsheet change to minimize hydrogen and ammonia generation during chemical processing of high level waste in the Defense Waste Processing Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, Dan P.; Woodham, Wesley H.; Williams, Matthew S.

Testing was completed to develop a chemical processing flowsheet for the Defense Waste Processing Facility (DWPF), designed to vitrify and stabilize high level radioactive waste. DWPF processing uses a reducing acid (formic acid) and an oxidizing acid (nitric acid) to rheologically thin the slurry and complete the necessary acid base and reduction reactions (primarily mercury and manganese). Formic acid reduces mercuric oxide to elemental mercury, allowing the mercury to be removed during the boiling phase of processing through steam stripping. In runs with active catalysts, formic acid can decompose to hydrogen and nitrate can be reduced to ammonia, both flammablemore » gases, due to rhodium and ruthenium catalysis. Replacement of formic acid with glycolic acid eliminates the generation of rhodium- and ruthenium-catalyzed hydrogen and ammonia. In addition, mercury reduction is still effective with glycolic acid. Hydrogen, ammonia and mercury are discussed in the body of the report. Ten abbreviated tests were completed to develop the operating window for implementation of the flowsheet and determine the impact of changes in acid stoichiometry and the blend of nitric and glycolic acid as it impacts various processing variables over a wide processing region. Three full-length 4-L lab-scale simulations demonstrated the viability of the flowsheet under planned operating conditions. The flowsheet is planned for implementation in early 2017.« less

Sludge batch 9 (SB9) acceptance evaluation. Radionuclide concentrations in tank 51 SB9 qualification sample prepared at SRNL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.; Diprete, D. P.; Pareizs, J. M.

Presented in this report are radionuclide concentrations required as part of the program of qualifying Sludge Batch 9 (SB9) for processing in the Defense Waste Processing Facility (DWPF). The SB9 material is currently in Tank 51 and has been washed and prepared for transfer to Tank 40. The acceptance evaluation needs to be completed prior to the transfer of the material in Tank 51 to Tank 40. The sludge slurry in Tank 40 has already been qualified for DWPF processing and is currently being processed as Sludge Batch 8 (SB8). The radionuclide concentrations were measured or estimated in the Tankmore » 51 SB9 Washed Qualification Sample prepared at Savannah River National Laboratory (SRNL). This sample was prepared from a three liter sample of Tank 51 sludge slurry (HTF-51-15-81) taken on July 23, 2015. The sample was delivered to SRNL where it was initially characterized in the Shielded Cells. Under the direction of Savannah River Remediation (SRR) it was then adjusted per the Tank Farm washing strategy as of October 20, 2015. This final slurry now has a composition expected to be similar to that of the slurry in Tank 51 after final preparations have been made for transfer of that slurry to Tank 40.« less

Sludge batch 9 (SB9) accepance evaluation: Radionuclide concentrations in tank 51 SB9 qualification sample prepared at SRNL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C.; Diprete, D.; Pareizs, J.

Presented in this report are radionuclide concentrations required as part of the program of qualifying Sludge Batch 9 (SB9) for processing in the Defense Waste Processing Facility (DWPF). The SB9 material is currently in Tank 51 and has been washed and prepared for transfer to Tank 40. The acceptance evaluation needs to be completed prior to the transfer of the material in Tank 51 to Tank 40. The sludge slurry in Tank 40 has already been qualified for DWPF processing and is currently being processed as Sludge Batch 8 (SB8). The radionuclide concentrations were measured or estimated in the Tankmore » 51 SB9 Washed Qualification Sample prepared at Savannah River National Laboratory (SRNL). This sample was prepared from a three liter sample of Tank 51 sludge slurry (HTF-51-15-81) taken on July 23, 2015. The sample was delivered to SRNL where it was initially characterized in the Shielded Cells. Under the direction of Savannah River Remediation (SRR) it was then adjusted per the Tank Farm washing strategy as of October 20, 2015. This final slurry now has a compositioniv expected to be similar to that of the slurry in Tank 51 after final preparations have been made for transfer of that slurry to Tank 40.« less

Final Report - Crystal Settling, Redox, and High Temperature Properties of ORP HLW and LAW Glasses, VSL-09R1510-1, Rev. 0, dated 6/18/09

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, Albert A.; Wang, C.; Gan, H.

2013-11-13

The radioactive tank waste treatment programs at the U. S. Department of Energy (DOE) have featured joule heated ceramic melter technology for the vitrification of high level waste (HLW). The Hanford Tank Waste Treatment and Immobilization Plant (WTP) employs this same basic technology not only for the vitrification of HLW streams but also for the vitrification of Low Activity Waste (LAW) streams. Because of the much greater throughput rates required of the WTP as compared to the vitrification facilities at the West Valley Demonstration Project (WVDP) or the Defense Waste Processing Facility (DWPF), the WTP employs advanced joule heated meltersmore » with forced mixing of the glass pool (bubblers) to improve heat and mass transport and increase melting rates. However, for both HLW and LAW treatment, the ability to increase waste loadings offers the potential to significantly reduce the amount of glass that must be produced and disposed and, therefore, the overall project costs. This report presents the results from a study to investigate several glass property issues related to WTP HLW and LAW vitrification: crystal formation and settling in selected HLW glasses; redox behavior of vanadium and chromium in selected LAW glasses; and key high temperature thermal properties of representative HLW and LAW glasses. The work was conducted according to Test Plans that were prepared for the HLW and LAW scope, respectively. One part of this work thus addresses some of the possible detrimental effects due to considerably higher crystal content in waste glass melts and, in particular, the impact of high crystal contents on the flow property of the glass melt and the settling rate of representative crystalline phases in an environment similar to that of an idling glass melter. Characterization of vanadium redox shifts in representative WTP LAW glasses is the second focal point of this work. The third part of this work focused on key high temperature thermal properties of representative WTP HLW and LAW glasses over a wide range of temperatures, from the melter operating temperature to the glass transition.« less

Modeling and simulation of large scale stirred tank

NASA Astrophysics Data System (ADS)

Neuville, John R.

The purpose of this dissertation is to provide a written record of the evaluation performed on the DWPF mixing process by the construction of numerical models that resemble the geometry of this process. There were seven numerical models constructed to evaluate the DWPF mixing process and four pilot plants. The models were developed with Fluent software and the results from these models were used to evaluate the structure of the flow field and the power demand of the agitator. The results from the numerical models were compared with empirical data collected from these pilot plants that had been operated at an earlier date. Mixing is commonly used in a variety ways throughout industry to blend miscible liquids, disperse gas through liquid, form emulsions, promote heat transfer and, suspend solid particles. The DOE Sites at Hanford in Richland Washington, West Valley in New York, and Savannah River Site in Aiken South Carolina have developed a process that immobilizes highly radioactive liquid waste. The radioactive liquid waste at DWPF is an opaque sludge that is mixed in a stirred tank with glass frit particles and water to form slurry of specified proportions. The DWPF mixing process is composed of a flat bottom cylindrical mixing vessel with a centrally located helical coil, and agitator. The helical coil is used to heat and cool the contents of the tank and can improve flow circulation. The agitator shaft has two impellers; a radial blade and a hydrofoil blade. The hydrofoil is used to circulate the mixture between the top region and bottom region of the tank. The radial blade sweeps the bottom of the tank and pushes the fluid in the outward radial direction. The full scale vessel contains about 9500 gallons of slurry with flow behavior characterized as a Bingham Plastic. Particles in the mixture have an abrasive characteristic that cause excessive erosion to internal vessel components at higher impeller speeds. The desire for this mixing process is to ensure the agitation of the vessel is adequate to produce a homogenous mixture but not so high that it produces excessive erosion to internal components. The main findings reported by this study were: (1) Careful consideration of the fluid yield stress characteristic is required to make predictions of fluid flow behavior. Laminar Models can predict flow patterns and stagnant regions in the tank until full movement of the flow field occurs. Power Curves and flow patterns were developed for the full scale mixing model to show the differences in expected performance of the mixing process for a broad range of fluids that exhibit Herschel--Bulkley and Bingham Plastic flow behavior. (2) The impeller power demand is independent of the flow model selection for turbulent flow fields in the region of the impeller. The laminar models slightly over predicted the agitator impeller power demand produced by turbulent models. (3) The CFD results show that the power number produced by the mixing system is independent of size. The 40 gallon model produced the same power number results as the 9300 gallon model for the same process conditions. (4) CFD Results show that the Scale-Up of fluid motion in a 40 gallon tank should compare with fluid motion at full scale, 9300 gallons by maintaining constant impeller Tip Speed.

SLUDGE BATCH 4 BASELINE MELT RATE FURNACE AND SLURRY-FED MELT RATE FURNACE TESTS WITH FRITS 418 AND 510 (U)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, M. E.; Jones, T. M.; Miller, D. H.

Several Slurry-Fed Melt Rate Furnace (SMRF) tests with earlier projections of the Sludge Batch 4 (SB4) composition have been performed.1,2 The first SB4 SMRF test used Frits 418 and 320, however it was found after the test that the REDuction/OXidation (REDOX) correlation at that time did not have the proper oxidation state for manganese. Because the manganese level in the SB4 sludge was higher than previous sludge batches tested, the impact of the higher manganese oxidation state was greater. The glasses were highly oxidized and very foamy, and therefore the results were inconclusive. After resolving this REDOX issue, Frits 418,more » 425, and 503 were tested in the SMRF with the updated baseline SB4 projection. Based on dry-fed Melt Rate Furnace (MRF) tests and the above mentioned SMRF tests, two previous frit recommendations were made by the Savannah River National Laboratory (SRNL) for processing of SB4 in the Defense Waste Processing Facility (DWPF). The first was Frit 503 based on the June 2006 composition projections.3 The recommendation was changed to Frit 418 as a result of the October 2006 composition projections (after the Tank 40 decant was implemented as part of the preparation plan). However, the start of SB4 processing was delayed due to the control room consolidation outage and the repair of the valve box in the Tank 51 to Tank 40 transfer line. These delays resulted in changes to the projected SB4 composition. Due to the slight change in composition and based on preliminary dry-fed MRF testing, SRNL believed that Frit 510 would increase throughput in processing SB4 in DWPF. Frit 418, which was used in processing Sludge Batch 3 (SB3), was a viable candidate and available in DWPF. Therefore, it was used during the initial SB4 processing. Due to the potential for higher melt rates with Frit 510, SMRF tests with the latest SB4 composition (1298 canisters) and Frits 510 and 418 were performed at a targeted waste loading (WL) of 35%. The '1298 canisters' describes the number of equivalent canisters that would be produced from the beginning of the current contract period before SB3 is blended with SB4. The melt rate for the SMRF SB4/Frit 510 test was 14.6 grams/minute. Due to cold cap mounding problems with the SMRF SB4/Frit 418 feed at 50 weight % solids that prevented a melt rate determination, this feed was diluted to 45 weight % solids. The melt rate for this diluted feed was 8.9 grams/minute. A correction factor of 1.2 for estimating the melt rate at 50 weight % solids from 45 weight % solids test results (based on previous SMRF testing5) was then used to estimate a melt rate of 10.7 grams/minute for SB4/Frit 418 at 50 weight % solids. Therefore, the use of Frit 510 versus Frit 418 with SB4 resulted in a higher melt rate (14.6 versus an estimated 10.7 grams/minute). For reference, a previous SMRF test with SB3/Frit 418 feed at 35% waste loading and 50 weight % solids resulted in a melt rate of 14.1 grams/minute. Therefore, depending on the actual feed rheology, the use of Frit 510 with SB4 could result in similar melt rates as experienced with SB3/Frit 418 feed in the DWPF.« less

Mercury Phase II Study - Mercury Behavior across the High-Level Waste Evaporator System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.; Crawford, C. L.; Jackson, D. G.

2016-06-17

The Mercury Program team’s effort continues to develop more fundamental information concerning mercury behavior across the liquid waste facilities and unit operations. Previously, the team examined the mercury chemistry across salt processing, including the Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit (ARP/MCU), and the Defense Waste Processing Facility (DWPF) flowsheets. This report documents the data and understanding of mercury across the high level waste 2H and 3H evaporator systems.

Road Map for Development of Crystal-Tolerant High Level Waste Glasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matyas, Josef; Vienna, John D.; Peeler, David

This road map guides the research and development for formulation and processing of crystal-tolerant glasses, identifying near- and long-term activities that need to be completed over the period from 2014 to 2019. The primary objective is to maximize waste loading for Hanford waste glasses without jeopardizing melter operation by crystal accumulation in the melter or melter discharge riser. The potential applicability to the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF) is also addressed in this road map.

INTERIOR VIEW, LOOKING WEST, WITH CRANE OPERATOR, TED SEALS, POURING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, LOOKING WEST, WITH CRANE OPERATOR, TED SEALS, POURING MOLTEN METAL INTO A 1,300 TON ELECTRIC HOLDING FURNACE OR MIXER. AN ELECTRONIC SCALE RECORDED THAT 50.5 TONS OF METAL WERE POURED INTO THE FURNACE DURING THIS POUR. - American Cast Iron Pipe Company, Mixer Building, 1501 Thirty-first Avenue North, Birmingham, Jefferson County, AL

The regional cerebral blood flow changes in major depressive disorder with and without psychotic features.

PubMed

Gonul, Ali Saffet; Kula, Mustafa; Bilgin, Arzu Guler; Tutus, Ahmet; Oguz, Aslan

2004-09-01

Depressive patients with psychotic features demonstrate distinct biological abnormalities in the hypothalamic-pituitary-adrenal axis (HPA), dopaminergic activity, electroencephalogram sleep profiles and measures of serotonergic function when compared to nonpsychotic depressive patients. However, very few functional neuroimaging studies were specifically designed for studying the effects of psychotic features on neuroimaging findings in depressed patients. The objective of the present study was to compare brain Single Photon Emission Tomography (SPECT) images in a group of unmedicated depressive patients with and without psychotic features. Twenty-eight patients who fully met DSM-IV criteria for major depressive disorder (MDD, 12 had psychotic features) were included in the study. They were compared with 16 control subjects matched for age, gender and education. Both psychotic and nonpsychotic depressed patients showed significantly lower regional cerebral blood flow (rCBF) values in the left and right superior frontal cortex, and left anterior cingulate cortex compared to those of controls. In comparison with depressive patients without psychotic features (DwoPF), depressive patients with psychotic features (DwPF) showed significantly lower rCBF perfusion ratios in left parietal cortex, left cerebellum but had higher rCBF perfusion ratio in the left inferior frontal cortex and caudate nucleus. The present study showed that DwPF have a different rCBF pattern compared to patients without psychotic features. Abnormalities involving inferior frontal cortex, striatum and cerebellum may play an important role in the generation of psychotic symptoms in depression.

Actual Waste Demonstration of the Nitric-Glycolic Flowsheet for Sludge Batch 9 Qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. D. Newell; Pareizs, J. M.; Martino, C. J.

For each sludge batch that is processed in the Defense Waste Processing Facility (DWPF), the Savannah River National Laboratory (SRNL) performs qualification testing to demonstrate that the sludge batch is processable. Testing performed by the Savannah River National Laboratory has shown glycolic acid to be effective in replacing the function of formic acid in the DWPF chemical process. The nitric-glycolic flowsheet reduces mercury, significantly lowers the catalytic generation of hydrogen and ammonia which could allow purge reduction in the Sludge Receipt and Adjustment Tank (SRAT), stabilizes the pH and chemistry in the SRAT and the Slurry Mix Evaporator (SME), allowsmore » for effective rheology adjustment, and is favorable with respect to melter flammability. In order to implement the new flowsheet, SRAT and SME cycles, designated SC-18, were performed using a Sludge Batch (SB) 9 slurry blended from SB8 Tank 40H and Tank 51H samples. The SRAT cycle involved adding nitric and glycolic acids to the sludge, refluxing to steam strip mercury, and dewatering to a targeted solids concentration. Data collected during the SRAT cycle included offgas analyses, process temperatures, heat transfer, and pH measurements. The SME cycle demonstrated the addition of glass frit and the replication of six canister decontamination additions. The demonstration concluded with dewatering to a targeted solids concentration. Data collected during the SME cycle included offgas analyses, process temperatures, heat transfer, and pH measurements. Slurry and condensate samples were collected for subsequent analysis« less

Alternate Reductant Cold Cap Evaluation Furnace Phase II Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, F. C.; Stone, M. E.; Miller, D. H.

2014-09-03

Savannah River Remediation (SRR) conducted a Systems Engineering Evaluation (SEE) to determine the optimum alternate reductant flowsheet for the Defense Waste Processing Facility (DWPF). Specifically, two proposed flowsheets (nitric–formic–glycolic and nitric–formic–sugar) were evaluated based upon results from preliminary testing. Comparison of the two flowsheets among evaluation criteria indicated a preference towards the nitric–formic–glycolic flowsheet. Further research and development of this flowsheet eliminated the formic acid, and as a result, the nitric–glycolic flowsheet was recommended for further testing. Based on the development of a roadmap for the nitric–glycolic acid flowsheet, Waste Solidification Engineering (WS-E) issued a Technical Task Request (TTR) tomore » address flammability issues that may impact the implementation of this flowsheet. Melter testing was requested in order to define the DWPF flammability envelope for the nitric-glycolic acid flowsheet. The Savannah River National Laboratory (SRNL) Cold Cap Evaluation Furnace (CEF), a 1/12 th scale DWPF melter, was selected by the SRR Alternate Reductant project team as the melter platform for this testing. The overall scope was divided into the following sub-tasks as discussed in the Task Technical and Quality Assurance Plan (TTQAP): Phase I - A nitric–formic acid flowsheet melter test (unbubbled) to baseline the CEF cold cap and vapor space data to the benchmark melter flammability models; Phase II - A nitric–glycolic acid flowsheet melter test (unbubbled and bubbled) to: Define new cold cap reactions and global kinetic parameters in support of the melter flammability model development; Quantify off-gas surging potential of the feed; Characterize off-gas condensate for complete organic and inorganic carbon species. After charging the CEF with cullet from Phase I CEF testing, the melter was slurry-fed with glycolic flowsheet based SB6-Frit 418 melter feed at 36% waste loading and was operated continuously for 25 days. Process data was collected throughout testing and included melter operation parameters and off-gas chemistry. In order to generate off-gas data in support of the flammability model development for the nitric-glycolic flowsheet, vapor space steady state testing in the range of ~300-750°C was conducted under the following conditions, (i) 100% (nominal and excess antifoam levels) and 125% stoichiometry feed and (ii) with and without argon bubbling. Adjustments to feed rate, heater outputs and purge air flow were necessary in order to achieve vapor space temperatures in this range. Surge testing was also completed under nominal conditions for four days with argon bubbling and one day without argon bubbling.« less

Glycolic acid physical properties and impurities assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D. P.; Pickenheim, B. R.; Bibler, N. E.

This document has been revised due to recent information that the glycolic acid used in Savannah River National Laboratory (SRNL) experiments contains both formaldehyde and methoxyacetic acid. These impurities were in the glycolic acid used in the testing included in this report and in subsequent testing using DuPont (now called Chemours) supplied Technical Grade 70 wt% glycolic acid. However, these impurities were not reported in earlier revisions. Additional data concerning the properties of glycolic acid have also been added to this report. The Defense Waste Processing Facility (DWPF) is planning to implement a nitric-glycolic acid flowsheets to increase attainment tomore » meet closure commitment dates during Sludge Batch 9. In fiscal year 2009, SRNL was requested to determine the physical properties of formic and glycolic acid blends. Blends of formic acid in glycolic acid were prepared and their physical properties tested. Increasing amounts of glycolic acid led to increases in blend density, viscosity and surface tension as compared to the 90 wt% formic acid that is currently used at DWPF. These increases are small, however, and are not expected to present any difficulties in terms of processing. The effect of sulfur impurities in Technical Grade glycolic acid was studied for its impact on DWPF glass quality. While the glycolic acid specification allows for more sulfate than the current formic acid specification, the ultimate impact is expected to be on the order of 0.033 wt% sulfur in glass. Note that lower sulfur content glycolic acid could likely be procured at some increased cost if deemed necessary. A paper study on the effects of radiation on glycolic acid was performed. The analysis indicates that substitution of glycolic acid for formic acid would not increase the radiolytic production rate of H2 and cause an adverse effect in the Slurry Receipt and Adjustment Tank (SRAT) or Slurry Mix Evaporator (SME) process. It has been cited that glycolic acid solutions that are depleted of O2 when subjected to large radiation doses produced considerable quantities of a non-diffusive polymeric material. Considering a constant air purge is maintained in the SRAT and the solution is continuously mixed, oxygen depletion seems unlikely, however, if this polymer is formed in the SRAT solution, the rheology of the solution may be affected and pumping of the solution may be hindered. However, an irradiation test with a simulated SRAT product supernate containing glycolic acid in an oxygen depleted atmosphere found no evidence of polymerization.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiedenman, B. J.; White, T. L.; Mahannah, R. N.

Ion Chromatography (IC) is the principal analytical method used to support studies of Sludge Reciept and Adjustment Tank (SRAT) chemistry at DWPF. A series of prior analytical ''Round Robin'' (RR) studies included both supernate and sludge samples from SRAT simulant, previously reported as memos, are tabulated in this report.2,3 From these studies it was determined to standardize IC column size to 4 mm diameter, eliminating the capillary column from use. As a follow on test, the DWPF laboratory, the PSAL laboratory, and the AD laboratory participated in the current analytical RR to determine a suite of anions in SRAT simulantmore » by IC, results also are tabulated in this report. The particular goal was to confirm the laboratories ability to measure and quantitate glycolate ion. The target was + or - 20% inter-lab agreement of the analyte averages for the RR. Each of the three laboratories analyzed a batch of 12 samples. For each laboratory, the percent relative standard deviation (%RSD) of the averages on nitrate, glycolate, and oxalate, was 10% or less. The three laboratories all met the goal of 20% relative agreement for nitrate and glycolate. For oxalate, the PSAL laboratory reported an average value that was 20% higher than the average values reported by the DWPF laboratory and the AD laboratory. Because of this wider window of agreement, it was concluded to continue the practice of an additional acid digestion for total oxalate measurement. It should also be noted that large amounts of glycolate in the SRAT samples will have an impact on detection limits of near eluting peaks, namely Fluoride and Formate. A suite of scoping experiments are presented in the report to identify and isolate other potential interlaboratory disceprancies. Specific ion chromatography inter-laboratory method conditions and differences are tabulated. Most differences were minor but there are some temperature control equipment differences that are significant leading to a recommendation of a heated jacket for analytical columns that are remoted for use in radiohoods. A suggested method improvement would be to implement column temperture control at a temperature slightly above ambient to avoid peak shifting due to temperature fluctuations. Temperature control in this manner would improve short and longer term peak retention time stability. An unknown peak was observed during the analysis of glycolic acid and SRAT simulant. The unknown peak was determined to best match diglycolic acid. The development of a method for acetate is summaraized, and no significant amount of acetate was observed in the SRAT products tested. In addition, an alternative Gas Chromatograph (GC) method for glycolate is summarized.« less

Low Phase Noise Fiber Optics Links for Space Applications

DTIC Science & Technology

2005-07-13

photo- oscillateur intégré pour 17 dB de pertes optiques Liaison active à 874,2 MHz avec photo- oscillateur intégré pour 18 dB de pertes optiques Liaison...active à 874,2 MHz avec photo- oscillateur intégré pour 20 dB de pertes optiques Liaison active à 874,2 MHz avec photo- oscillateur intégré pour 23 dB...de pertes optiques Liaison active à 874,2 MHz avec photo- oscillateur intégré pour 25 dB de pertes optiques Liaison active à 874,2 MHz avec photo

Effect of storage time of extended-pour and conventional alginate impressions on dimensional accuracy of casts.

PubMed

Rohanian, Ahmad; Ommati Shabestari, Ghasem; Zeighami, Somayeh; Samadi, Mohammad Javad; Shamshiri, Ahmad Reza

2014-11-01

Some manufacturers claim to have produced new irreversible hydro-colloids that are able to maintain their dimensional stability during storage. The present study evaluated the effect of storage time on dimensional stability of three alginates: Hydrogum 5, Tropicalgin and Alginoplast. In this experimental in-vitro trial, a total of 90 alginate impressions were made from a Dentoform model using Hydrogum 5, Tropicalgin and Alginoplast alginates. The impressions were stored in a sealed plastic bag without a damp paper towel for 0, 24, 48, 72 and 120 hours and then poured with type III dental stone. Cross-arch (facial of 6 to facial of 6 on the opposite side) and antero-posterior (distal of right first molar to the ipsilateral central incisor) measurements were made with a digital caliper on the casts. Data were analyzed by two-way and one-way ANOVA and Tukey's post-hoc test (P<0.05). Alginate type and the pouring time significantly affected the dimensional stability of alginate impressions (both Ps<0.001). Pouring of Hydrogum 5 impressions can be delayed for up to 120 hours without significant dimensional changes. Alginoplast impressions may be poured after 72 hours, but Tropicalgin should be poured immediately and the storage time should not be more than 24 hours. Immediate pouring of alginate impressions provides the highest accuracy in reproducing the teeth and adjacent tissues; however, this study demonstrated that pouring may be delayed for up to five days using extended-pour (Hydrogum 5) alginates.

Patient-related risk factors for urinary retention following ambulatory general surgery: a systematic review and meta-analysis.

PubMed

Mason, Sam E; Scott, Alasdair J; Mayer, Erik; Purkayastha, Sanjay

2016-06-01

Postoperative urinary retention (POUR) is a source of avoidable patient harm. The aim of this review is to identify and quantify the role of patient-related risk factors in the development of POUR following ambulatory general surgery. Studies published until December 2014 were identified by searching MEDLINE, EMBASE, and PsycINFO databases. Risk factors assessed in 3 or more studies were meta-analyzed. Twenty-one studies were suitable for inclusion consisting of 7,802 patients. The incidence of POUR was 14%. Increased age and the presence of lower urinary tract symptoms significantly increased risk with odds ratios [ORs] of 2.11 (95% confidence interval [CI] 1.15 to 3.86) and 2.83 (1.57 to 5.08), respectively. Male sex was not associated with developing POUR (OR .96, 95% CI .62 to 1.50). Preoperative α-blocker use significantly decreased the incidence of POUR with an OR of .37 (95% CI .15 to .91). Increased age and the presence of lower urinary tract symptoms increase the risk of POUR, while α-blocker use confers protection. Male sex was not associated with POUR. These findings assist in preoperative identification of patients at high risk of POUR. Copyright © 2015 Elsevier Inc. All rights reserved.

The evolution of groundwater rights and groundwater management in New Mexico and the western United States

NASA Astrophysics Data System (ADS)

DuMars, Charles T.; Minier, Jeffrie D.

Historically, rights in water originated as public property and only later became individualized rights to utilize the public resource, in a manner consistent with the public welfare needs of society, but protected by principles of property law. Five basic regulatory systems for rights in groundwater in the United States have evolved to date. The problems raised by the hydrologic differences between groundwater hydraulically connected to stream systems and groundwater in non-replenished aquifers have been resolved to some extent by a couple of leading court cases. Numerical modeling and other technical methodologies have also evolved to evaluate the scientific issues raised by the different hydrologic conditions, but these are not immune from criticism. The current role of aquifers is evolving into that of storage facilities for recycled water, and their utilization in this manner may be expanded even further in the future. The policy implications of the choices relating to joint management of ground and surface water cannot be overstated. As this paper demonstrates, proactive administration of future groundwater depletions that affect stream systems is essential to the ultimate ability to plan for exploitation, management and utilization of water resources in a rational way that coordinates present and future demand with the reality of scarcity of supply. The examples utilized in this paper demonstrate the need for capacity building, not just to develop good measurement techniques, or to train talented lawyers and judges to write good laws, but also for practical professional water managers to keep the process on a rational course, avoiding limitless exploitation of the resource as well as conservative protectionism that forever precludes its use. Historiquement, les droits d'eau étaient à l'origine un bien public; ils sont devenus plus tard des droits individualisés pour utiliser la ressource publique conformément aux besoins de salut public de la société, mais protégés par des principes de lois de propriété. Cinq systèmes de réglementation de base pour les droits sur les eaux souterraines aux États-Unis ont évolué jusqu'à aujourd'hui. Les problèmes posés par les différences hydrologiques entre les eaux souterraines hydrauliquement connectées aux cours d'eau et celles d'aquifères non réalimentés ont été résolus jusqu'à un certain point par quelques cas de jugement. La modélisation numérique et d'autres méthodologies techniques ont également évolué pour évaluer les résultats scientifiques apportés dans différentes conditions hydrologiques, mais ne sont pas à l'abri de critiques. Le rôle courant des aquifères évolue entre celui des possibilités de stockage pour l'eau recyclée et leur utilisation dans ce but peut être même étendue plus loin dans le futur. Les implications politiques des choix relatifs à la gestion simultanée des eaux souterraines et de surface ne doivent pas être exagérées. Comme le montre cet article, la gestion active de l'épuisement futur des nappes qui affecte les systèmes fluviaux est essentielle pour la capacité finale à planifier l'exploitation, la gestion et l'utilisation des ressources en eau d'une manière rationnelle qui coordonne la demande actuelle et future à la réalité de la rareté de l'alimentation. Les exemples utilisés dans cet article démontrent le besoin d'une capacité d'élaboration, non seulement pour développer de bonnes techniques de mesure, ou pour former d'excellents avocats et juges pour écrire de bonnes lois, mais aussi pour que des praticiens gestionnaires de l'eau maintiennent le processus dans un cours rationnel pour éviter une exploitation sans limite des ressources aussi bien qu'un protectionnisme conservateur qui empêche son usage à jamais. Históricamente, los derechos del agua se originaron como un bien público que se transformaron después en derechos individualizados para usar los recursos públicos, de forma coherente con las necesidades de bienestar social, pero protegidos por los principios de la ley de propiedad. Hasta el momento, cinco sistemas reguladores básicos han evolucionado en los Estados Unidos de América en relación a los derechos en las aguas subterráneas. Los problemas surgidos por las diferencias hidrológicas entre las aguas subterráneas conectadas a corrientes superficiales y las aguas subterráneas en acuíferos sobreexplotados han sido resueltos hasta cierto punto por un par de casos judiciales notables. La modelación numérica y otras metodologías técnicas han evolucionado también para evaluar aspectos científicos asociados a diversas circunstancias hidrológicas, pero no son inmunes a las críticas. El papel actual de los acuíferos está evolucionando hacia el de instalaciones de almacenamiento de agua reciclada y su utilización de esta forma puede expandirse incluso más en el futuro. Las implicaciones políticas de las decisiones relativas a la gestión conjunta de las aguas superficiales y subterráneas no pueden ser exageradas. Como este artículo demuestra, una administración proactiva de las extracciones futuras de aguas subterráneas con efectos en los ecosistemas superficiales es esencial para la capacidad final de planificar la explotación, gestión y utilización de los recursos hídricos de forma racional, coordinando las demandas presentes y futuras con la realidad de la escasez de suministro. Los ejemplos empleados en este artículo demuestran la necesidad de construir capacidad y no únicamente de desarrollar buenas técnicas de medida, o la de educar reguladores y jueces de talento que redacten buenas leyes, pero también de gestores profesionales y aplicados del agua que mantengan el proceso en un compromiso entre evitar la explotación ilimitada del recurso y ejercer un proteccionismo conservador que impida su uso para siempre.

Alternative Submarine Watch Systems: Recommendation for a New CF Submarine Watch Schedule (Systemes Differents d’Horaire de Garde a Bord des Sous-Marins: Nouvel Horaire Recommande Pour les Sous-Marins des FC)

DTIC Science & Technology

2010-01-01

comparativement à une efficacité cognitive de 96 % pour l’horaire de 1 tour sur trois de quatre heures ainsi que pour l’horaire de 1 tour sur trois de...tour sur 2 (8-4-4-8) comparativement à une efficacité cognitive de 96 % pour l’horaire de 1 tour sur trois de quatre heures ainsi que pour l’horaire...FAST™ (Fatigue Avoidance and Safety Tool), a computer application designed to predict and prevent fatigue in operational settings. The output of FAST

FRONT VIEW OF POURING FROM #61 HOLDING FURNACE AT #02 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FRONT VIEW OF POURING FROM #61 HOLDING FURNACE AT #02 STATION INTO THREE VERTICAL MOLDS SUBMERGED IN A WATER-FILLED TANK BELOW THE CASTING FLOOR. THE CASTING CREW'S JOBS DURING THIS PHASE OF THE OPERATION INCLUDE REGULATING THE POURING RATE AND MONITORING THE VALVE RODS THAT CONTROL THE WATER SPRAYS ON THE MOLDS. DIFFERENT ALLOYS REQUIRE SPECIFIC POURING SPEEDS AND WATER PRESSURES. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY

Influence of volume ratio of liquid to solid and low pouring temperature on interface structure of cast Babbitt-steel bimetal composite

NASA Astrophysics Data System (ADS)

Fathy, Naglaa; Ramadan, Mohamed

2018-05-01

The influence of volume ratio of liquid to Solid and low pouring temperature on interface structure of cast Babbitt-steel bimetal composite was evaluated for static casting technique. At low pouring temperature of 380 °C, Babbitt microstructures are improved to be finer and more globular. On the other side pouring the Babbitt at low pouring temperature of 380 °C increases the chance of present higher unbonded area percent. Increasing the volume ratio of liquid to solid decreases the Sn-Pb interface thicknesses and increases the bonded interface area. In order to optimize the production of Babbitt-steel bimetal composite at low pouring temperature, the volume ratio of liquid Babbitt to solid steel shell should be higher value that could be more than 5 depending on the extrapolation of current data presented.

The Kaye effect

NASA Astrophysics Data System (ADS)

Binder, J. M.; Landig, A. J.

2009-11-01

The International Young Physicists' Tournament (IYPT) is a worldwide, annual competition for secondary school students. This is our solution to problem number 10, The Kaye effect, as presented in the final round of the 21st IYPT in Trogir, Croatia. The Kaye effect occurs when a thin stream of shampoo or a different adequate non-Newtonian liquid is poured onto a surface. Suddenly, a jet leaves the heap that is formed by the shampoo and begins to 'dance' around the primary jet like a lasso. The phenomenon ends when the 'dancing' jet hits the primary jet and subsequently collapses. We started our investigations based on available literature (Kaye 1963 Nature 197 1001, Versluis et al 2006 J. Stat. Mech., Collyer and Fischer 1976 Nature 261 682). We made experiments with a similar experimental set-up in which we could determine the velocities of both shampoo streams as well as the angle of the 'dancing' stream. From there on, we developed a theoretical model for the energy loss of the jet in the heap. We discovered that the air layer between the jet and the heap is a necessity for the Kaye effect to occur. At this point, our observations differ from the aforementioned literature. This also accounts for the shampoo beam acting as a light guide. Further experiments concerning the viscoelasticity of the shampoo revealed that the elastic property of the shampoo is necessary for the effect to occur. This article is a written version of the oral contribution of the German team to the 21st IYPT competition, which was awarded first prize by an international jury. The article has been edited by European Journal of Physics.

Pilot-scale tests of HEME and HEPA dissolution process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qureshi, Z.H.; Strege, D.K.

A series of pilot-scale demonstration tests for the dissolution of High Efficiency Mist Eliminators (HEME`s) and High Efficiency Particulate Airfilters (HEPA) were performed on a 1/5th linear scale. These fiberglass filters are to be used in the Defense Waste Processing Facility (DWPF) to decontaminate the effluents from the off-gases generated during the feed preparation process and vitrification. When removed, these filters will be dissolved in the Decontamination Waste Treatment Tank (DWTT) using 5 wt% NaOH solution. The contaminated fiberglass is converted to an aqueous stream which will be transferred to the waste tanks. The filter metal structure will be rinsedmore » with process water before its disposal as low-level solid waste. The pilot-scale study reported here successfully demonstrated a simple one step process using 5 wt% NaOH solution. The proposed process requires the installation of a new water spray ring with 30 nozzles. In addition to the reduced waste generated, the total process time is reduced to 48 hours only (66% saving in time). The pilot-scale tests clearly demonstrated that the dissolution process of HEMEs has two stages - chemical digestion of the filter and mechanical erosion of the digested filter. The digestion is achieved by a boiling 5 wt% caustic solutions, whereas the mechanical break down of the digested filter is successfully achieved by spraying process water on the digested filter. An alternate method of breaking down the digested filter by increased air sparging of the solution was found to be marginally successful are best. The pilot-scale tests also demonstrated that the products of dissolution are easily pumpable by a centrifugal pump.« less

Effect of Storage Time of Extended-Pour and Conventional Alginate Impressions on Dimensional Accuracy of Casts

PubMed Central

Rohanian, Ahmad; Ommati Shabestari, Ghasem; Zeighami, Somayeh; Samadi, Mohammad Javad; Shamshiri, Ahmad Reza

2014-01-01

Objectives: Some manufacturers claim to have produced new irreversible hydro-colloids that are able to maintain their dimensional stability during storage. The present study evaluated the effect of storage time on dimensional stability of three alginates: Hydrogum 5, Tropicalgin and Alginoplast. Materials and Methods: In this experimental in-vitro trial, a total of 90 alginate impressions were made from a Dentoform model using Hydrogum 5, Tropicalgin and Alginoplast alginates. The impressions were stored in a sealed plastic bag without a damp paper towel for 0, 24, 48, 72 and 120 hours and then poured with type III dental stone. Cross-arch (facial of 6 to facial of 6 on the opposite side) and antero-posterior (distal of right first molar to the ipsilateral central incisor) measurements were made with a digital caliper on the casts. Data were analyzed by two-way and one-way ANOVA and Tukey’s post-hoc test (P<0.05). Results: Alginate type and the pouring time significantly affected the dimensional stability of alginate impressions (both Ps<0.001). Pouring of Hydrogum 5 impressions can be delayed for up to 120 hours without significant dimensional changes. Alginoplast impressions may be poured after 72 hours, but Tropicalgin should be poured immediately and the storage time should not be more than 24 hours. Conclusion: Immediate pouring of alginate impressions provides the highest accuracy in reproducing the teeth and adjacent tissues; however, this study demonstrated that pouring may be delayed for up to five days using extended-pour (Hydrogum 5) alginates. PMID:25628695

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE KSC-375C-10036.31 108-KSC-375C-10036.31, P-21426, ARCHIVE-04502 Aerial oblique of Shuttle runway facilities. Pouring concrete on runway. Direction north - altitude 100'.

Identification des parametres du moteur de l'avion Cessna Citation X pour la phase de croisiere a partir des tests en vol et a base des reseaux de neurones =

NASA Astrophysics Data System (ADS)

Zaag, Mahdi

La disponibilite des modeles precis des avions est parmi les elements cles permettant d'assurer leurs ameliorations. Ces modeles servent a ameliorer les commandes de vol et de concevoir de nouveaux systemes aerodynamiques pour la conception des ailes deformables des avions. Ce projet consiste a concevoir un systeme d'identification de certains parametres du modele du moteur de l'avion d'affaires americain Cessna Citation X pour la phase de croisiere a partir des essais en vol. Ces essais ont ete effectues sur le simulateur de vol concu et fabrique par CAE Inc. qui possede le niveau D de la dynamique de vol. En effet, le niveau D est le plus haut niveau de precision donne par l'autorite federale de reglementation FAA de l'aviation civile aux Etats-Unis. Une methodologie basee sur les reseaux de neurones optimises a l'aide d'un algorithme intitule le "grand deluge etendu" est utilisee dans la conception de ce systeme d'identification. Plusieurs tests de vol pour differentes altitudes et differents nombres de Mach ont ete realises afin de s'en servir comme bases de donnees pour l'apprentissage des reseaux de neurones. La validation de ce modele a ete realisee a l'aide des donnees du simulateur. Malgre la nonlinearite et la complexite du systeme, les parametres du moteur ont ete tres bien predits pour une enveloppe de vol determinee. Ce modele estime pourrait etre utilise pour des analyses de fonctionnement du moteur et pourrait assurer le controle de l'avion pendant cette phase de croisiere. L'identification des parametres du moteur pourrait etre realisee aussi pour les autres phases de montee et de descente afin d'obtenir son modele complet pour toute l'enveloppe du vol de l'avion Cessna Citation X (montee, croisiere, descente). Cette methode employee dans ce travail pourrait aussi etre efficace pour realiser un modele pour l'identification des coefficients aerodynamiques du meme avion a partir toujours des essais en vol. None None None

Defense Waste Processing Facility Canister Closure Weld Current Validation Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korinko, P. S.; Maxwell, D. N.

Two closure welds on filled Defense Waste Processing Facility (DWPF) canisters failed to be within the acceptance criteria in the DWPF operating procedure SW4-15.80-2.3 (1). In one case, the weld heat setting was inadvertently provided to the canister at the value used for test welds (i.e., 72%) and this oversight produced a weld at a current of nominally 210 kA compared to the operating procedure range (i.e., 82%) of 240 kA to 263 kA. The second weld appeared to experience an instrumentation and data acquisition upset. The current for this weld was reported as 191 kA. Review of the datamore » from the Data Acquisition System (DAS) indicated that three of the four current legs were reading the expected values, approximately 62 kA each, and the fourth leg read zero current. Since there is no feasible way by further examination of the process data to ascertain if this weld was actually welded at either the target current or the lower current, a test plan was executed to provide assurance that these Nonconforming Welds (NCWs) meet the requirements for strength and leak tightness. Acceptance of the welds is based on evaluation of Test Nozzle Welds (TNW) made specifically for comparison. The TNW were nondestructively and destructively evaluated for plug height, heat tint, ultrasonic testing (UT) for bond length and ultrasonic volumetric examination for weld defects, burst pressure, fractography, and metallography. The testing was conducted in agreement with a Task Technical and Quality Assurance Plan (TTQAP) (2) and applicable procedures.« less

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY KSC-375C-10036.32 108-KSC-375C-10036.32, P-21425, ARCHIVE-04501 Aerial oblique of Shuttle Landing Facility. Pouring concrete on runway. Direction North - Altitude 100'.

Etude numérique et expérimentale de l'evaporation d'une ou plusieurs gouttes de mélange de carburants dans un écoulement chauffé

NASA Astrophysics Data System (ADS)

Daïf, A.; Ali Chérif, A.; Bresson, J.; Sarh, B.

1995-10-01

The vaporization of one or two multi-component fuel droplets in hot air-stream is presented. A thermal wind tunnel with experimental channel has been designed to develop an experimental process. Firstly, the comparison between experimental results and numerical data is presented for the case of an isolated multi-component droplet. The numerical method is based on the resolution of heat and mass transfer equations between the droplet and the gas stream. This model includes the effect of Stephan flow, the effect of variable thermophysical properties of the components, and the non-unitary Lewis number in the gas film. The experimental results show the micro-explosion phenomenon observed in the liquid phase of multi-component droplet at low temperature. The experimental case of two pure or multi-component droplets in interaction is also presented. On présente un article de synthèse sur l'évaporation d'une ou deux gouttes de carburants à plusieurs composants dans un écoulement d'air chaud. Un dispositif expérimental constitué d'une soufflerie thermique, avec veine d'expérimentation, est réalisé pour permettre cette étude. Pour le cas d'une goutte isolée, une comparaison expérience-calcul est entreprise. Le principe de la méthode numerique consiste en la résolution des équations de transfert de masse et de chaleur entre la goutte et l'écoulement. Ce modèle prend en compte les effets de l'écoulement de Stephan, les variations des propriétés thermophysiques des composants dans les deux phases et la valeur du nombre de Lewis différente de l'unité dans le film de vapeur. Outre l'analyse plus approfondie qu'apporte la confrontation entre le calcul et l'expérience, les résultats expérimentaux montrent le phénomène de micro-explosion observé à l'intérieur de la goutte liquide. Le cas expérimental de deux gouttes en interaction est abordé qu'il s'agisse de gouttes de carburant pur ou de mélange.

High Level Waste System Impacts from Small Column Ion Exchange Implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCabe, D. J.; Hamm, L. L.; Aleman, S. E.

2005-08-18

The objective of this task is to identify potential waste streams that could be treated with the Small Column Ion Exchange (SCIX) and perform an initial assessment of the impact of doing so on the High-Level Waste (HLW) system. Design of the SCIX system has been performed as a backup technology for decontamination of High-Level Waste (HLW) at the Savannah River Site (SRS). The SCIX consists of three modules which can be placed in risers inside underground HLW storage tanks. The pump and filter module and the ion exchange module are used to filter and decontaminate the aqueous tank wastesmore » for disposition in Saltstone. The ion exchange module contains Crystalline Silicotitanate (CST in its engineered granular form is referred to as IONSIV{reg_sign} IE-911), and is selective for removal of cesium ions. After the IE-911 is loaded with Cs-137, it is removed and the column is refilled with a fresh batch. The grinder module is used to size-reduce the cesium-loaded IE-911 to make it compatible with the sludge vitrification system in the Defense Waste Processing Facility (DWPF). If installed at the SRS, this SCIX would need to operate within the current constraints of the larger HLW storage, retrieval, treatment, and disposal system. Although the equipment has been physically designed to comply with system requirements, there is also a need to identify which waste streams could be treated, how it could be implemented in the tank farms, and when this system could be incorporated into the HLW flowsheet and planning. This document summarizes a preliminary examination of the tentative HLW retrieval plans, facility schedules, decontamination factor targets, and vitrified waste form compatibility, with recommendations for a more detailed study later. The examination was based upon four batches of salt solution from the currently planned disposition pathway to treatment in the SCIX. Because of differences in capabilities between the SRS baseline and SCIX, these four batches were combined into three batches for a total of about 3.2 million gallons of liquid waste. The chemical and radiological composition of these batches was estimated from the SpaceMan Plus{trademark} model using the same data set and assumptions as the baseline plans.« less

Another First at NSLS-II Construction Site

ScienceCinema

None

2017-12-09

Workers at the NSLS-II ring building construction site recently completed the first complicated concrete pour for the approximately 19-ft.-tall walls of the Utility Tunnel. The continuous pour was the first of its kind, as previous pours have been for foo

Solidification Based Grain Refinement in Steels

DTIC Science & Technology

2011-09-27

project (Tasks 7-9). An industrial trial on an investment casting was done using rare earth silicide additions in a furnace prior to pouring (Task 7...an investment casting was done using rare earth silicide additions in a furnace prior to pounng (la.sk 7). Some of the test parts had a finer...poured at the end of a six casting batch. One test tree with no RE addition was poured. Before the second test tree was poured, sufficient RE silicide was

Métamatériaux pour la protection sismique

NASA Astrophysics Data System (ADS)

Guenneau, Sébastien; Enoch, Stefan; Colombi, Andrea; Roux, Philippe; Brule, Stéphane

2018-02-01

Les physiciens des ondes élaborent des modèles théoriques et numériques pour un contrôle accru de la lumière dans des matériaux structurés à l'échelle nanométrique et s'en inspirent pour contrôler les ondes mécaniques de Rayleigh dans des sols structurés à l'échelle métrique, avec des trous dans un sol ou des arbres en surface savamment agencés. Un transfert de paradigme s'opère entre les métamatériaux électromagnétiques pour la photonique et les métamatériaux sismiques pour le génie civil.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newell, J; Miller, D; Stone, M

The Savannah River National Laboratory (SRNL) was tasked to provide an assessment of the downstream impacts to the Defense Waste Processing Facility (DWPF) of decisions regarding the implementation of Al-dissolution to support sludge mass reduction and processing. Based on future sludge batch compositional projections from the Liquid Waste Organization's (LWO) sludge batch plan, assessments have been made with respect to the ability to maintain comparable projected operating windows for sludges with and without Al-dissolution. As part of that previous assessment, candidate frits were identified to provide insight into melt rate for average sludge batches representing with and without Al-dissolution flowsheets.more » Initial melt rate studies using the melt rate furnace (MRF) were performed using five frits each for Cluster 2 and Cluster 4 compositions representing average without and with Al-dissolution. It was determined, however, that the REDOX endpoint (Fe{sup 2+}/{Sigma}Fe for the glass) for Clusters 2 and 4 resulted in an overly oxidized feed which negatively affected the initial melt rate tests. After the sludge was adjusted to a more reduced state, additional testing was performed with frits that contained both high and low concentrations of sodium and boron oxides. These frits were selected strictly based on the ability to ascertain compositional trends in melt rate and did not necessarily apply to any acceptability criteria for DWPF processing. The melt rate data are in general agreement with historical trends observed at SRNL and during processing of SB3 (Sludge Batch 3)and SB4 in DWPF. When MAR acceptability criteria were applied, Frit 510 was seen to have the highest melt rate at 0.67 in/hr for Cluster 2 (without Al-dissolution), which is compositionally similar to SB4. For Cluster 4 (with Al-dissolution), which is compositionally similar to SB3, Frit 418 had the highest melt rate at 0.63 in/hr. Based on this data, there appears to be a slight advantage of the Frit 510 based system without Al-dissolution relative to the Frit 418 based system with Al-dissolution. Though the without aluminum dissolution scenario suggests a slightly higher melt rate with frit 510, several points must be taken into consideration: (1) The MRF does not have the ability to assess liquid feeds and, thus, rheology impacts. Instead, the MRF is a 'static' test bed in which a mass of dried melter feed (SRAT product plus frit) is placed in an 'isothermal' furnace for a period of time to assess melt rate. These conditions, although historically effective in terms of identifying candidate frits for specific sludge batches and mapping out melt rate versus waste loading trends, do not allow for assessments of the potential impact of feed rheology on melt rate. That is, if the rheological properties of the slurried melter feed resulted in the mounding of the feed in the melter (i.e., the melter feed was thick and did not flow across the cold cap), melt rate and/or melter operations (i.e., surges) could be negatively impacted. This could affect one or both flowsheets. (2) Waste throughput factors were not determined for Frit 510 and Frit 418 over multiple waste loadings. In order to provide insight into the mission life versus canister count question, one needs to define the maximum waste throughput for both flowsheets. Due to funding limitations, the melt rate testing only evaluated melt rate at a fixed waste loading. (3) DWPF will be processing SB5 through their facility in mid-November 2008. Insight into the over arching questions of melt rate, waste throughput, and mission life can be obtained directly from the facility. It is recommended that processing of SB5 through the facility be monitored closely and that data be used as input into the decision making process on whether to implement Al-dissolution for future sludge batches.« less

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2014 CFR

2014-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

Analysis Of 2H-Evaporator Scale Pot Bottom Sample [HTF-13-11-28H

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oji, L. N.

2013-07-15

Savannah River Remediation (SRR) is planning to remove a buildup of sodium aluminosilicate scale from the 2H-evaporator pot by loading and soaking the pot with heated 1.5 M nitric acid solution. Sampling and analysis of the scale material from the 2H evaporator has been performed so that the evaporator can be chemically cleaned beginning July of 2013. Historically, since the operation of the Defense Waste Processing Facility (DWPF), silicon in the DWPF recycle stream combines with aluminum in the typical tank farm supernate to form sodium aluminosilicate scale mineral deposits in the 2H-evaporator pot and gravity drain line. The 2H-evaporatormore » scale samples analyzed by Savannah River National Laboratory (SRNL) came from the bottom cone sections of the 2H-evaporator pot. The sample holder from the 2H-evaporator wall was virtually empty and was not included in the analysis. It is worth noting that after the delivery of these 2H-evaporator scale samples to SRNL for the analyses, the plant customer determined that the 2H evaporator could be operated for additional period prior to requiring cleaning. Therefore, there was no need for expedited sample analysis as was presented in the Technical Task Request. However, a second set of 2H evaporator scale samples were expected in May of 2013, which would need expedited sample analysis. X-ray diffraction analysis (XRD) confirmed the bottom cone section sample from the 2H-evaporator pot consisted of nitrated cancrinite, (a crystalline sodium aluminosilicate solid), clarkeite and uranium oxide. There were also mercury compound XRD peaks which could not be matched and further X-ray fluorescence (XRF) analysis of the sample confirmed the existence of elemental mercury or mercuric oxide. On ''as received'' basis, the scale contained an average of 7.09E+00 wt % total uranium (n = 3; st.dev. = 8.31E-01 wt %) with a U-235 enrichment of 5.80E-01 % (n = 3; st.dev. = 3.96E-02 %). The measured U-238 concentration was 7.05E+00 wt % (n=3, st. dev. = 8.25E-01 wt %). Analyses results for Pu-238 and Pu-239, and Pu-241 are 7.06E-05 {+-} 7.63E-06 wt %, 9.45E-04 {+-} 3.52E-05 wt %, and <2.24E-06 wt %, respectively. These results are provided so that SRR can calculate the equivalent uranium-235 concentrations for the NCSA. Because this 2H evaporator pot bottom scale sample contained a significant amount of elemental mercury (11.7 wt % average), it is recommended that analysis for mercury be included in future Technical Task Requests on 2H evaporator sample analysis at SRNL. Results confirm that the uranium contained in the scale remains depleted with respect to natural uranium. SRNL did not calculate an equivalent U-235 enrichment, which takes into account other fissionable isotopes U-233, Pu-239 and Pu-241.« less

Results For The Fourth Quarter 2014 Tank 50 WAC Slurry Sample: Chemical And Radionuclide Contaminants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.

2015-09-30

This report details the chemical and radionuclide contaminant results for the characterization of the Calendar Year (CY) 2014 Fourth Quarter sampling of Tank 50 for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time. Information from this characterization will be used by DWPF & Saltstone Facility Engineering (DSFE) to support the transfer of low-level aqueous waste from Tank 50 to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50 Waste Characterization System.

Rheological Characterization of Unusual DWPF Slurry Samples (U)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, D. C.

2005-09-01

A study was undertaken to identify and clarify examples of unusual rheological behavior in Defense Waste Processing Facility (DWPF) simulant slurry samples. Identification was accomplished by reviewing sludge, Sludge Receipt and Adjustment Tank (SRAT) product, and Slurry Mix Evaporator (SME) product simulant rheological results from the prior year. Clarification of unusual rheological behavior was achieved by developing and implementing new measurement techniques. Development of these new methods is covered in a separate report, WSRC-TR-2004-00334. This report includes a review of recent literature on unusual rheological behavior, followed by a summary of the rheological measurement results obtained on a set ofmore » unusual simulant samples. Shifts in rheological behavior of slurries as the wt. % total solids changed have been observed in numerous systems. The main finding of the experimental work was that the various unusual DWPF simulant slurry samples exhibit some degree of time dependent behavior. When a given shear rate is applied to a sample, the apparent viscosity of the slurry changes with time rather than remaining constant. These unusual simulant samples are more rheologically complex than Newtonian liquids or more simple slurries, neither of which shows significant time dependence. The study concludes that the unusual rheological behavior that has been observed is being caused by time dependent rheological properties in the slurries being measured. Most of the changes are due to the effect of time under shear, but SB3 SME products were also changing properties while stored in sample bottles. The most likely source of this shear-related time dependence for sludge is in the simulant preparation. More than a single source of time dependence was inferred for the simulant SME product slurries based on the range of phenomena observed. Rheological property changes were observed on the time-scale of a single measurement (minutes) as well as on a time scale of hours to weeks. The unusual shape of the slurry flow curves was not an artifact of the rheometric measurement. Adjusting the user-specified parameters in the rheometer measurement jobs can alter the shape of the flow curve of these time dependent samples, but this was not causing the unusual behavior. Variations in the measurement parameters caused the time dependence of a given slurry to manifest at different rates. The premise of the controlled shear rate flow curve measurement is that the dynamic response of the sample to a change in shear rate is nearly instantaneous. When this is the case, the data can be fitted to a time independent rheological equation, such as the Bingham plastic model. In those cases where this does not happen, interpretation of the data is difficult. Fitting time dependent data to time independent rheological equations, such as the Bingham plastic model, is also not appropriate.« less

Refractive Surgery: New Techniques and Usability for Military Personnel (La chirurgie refractive: Nouvelles techniques et leur application pour le personnel militaire)

DTIC Science & Technology

2012-11-01

de loin sans correction, la chirurgie réfractive permet aux jeunes recrues ou militaires du rang de satisfaire aux normes de vision sans...correction exigées pour le métier militaire de leur choix, d’où une augmentation du nombre de candidats et la possibilité pour les individus...réfractive risquent d’engendrer des handicaps visuels et d’écourter des carrières militaires. Pour cette raison, la qualité du service fourni

Que peut-on voir avec des neutrons? Une introduction pour des non spécialistes

NASA Astrophysics Data System (ADS)

Schweizer, J.

2005-11-01

Le neutron est une particule élémentaire qui a été découverte en 1932 par James Chadwick. Ses caractéristiques principales sont résumées dans le tableau I. Il a été utilisé pour la première fois par Clifford Shull en 1946 comme outil pour des expériences de diffusion. Cette technique s'est depuis constamment développée pour concerner tous les aspects de la matière condensée: physique, chimie, matériaux, biologie. Il s'agit d'un outil tout à fait exceptionnel car le neutron possède des propriétés uniques et particulièrement adaptées pour ces études.

Profil épidémiologique des pathologies respiratoires chez l’enfant à l’Hôpital d’Enfants de Rabat, Maroc

PubMed Central

Benchekroun, Ilham; Boubkraoui, Mohamed El Mahdi; Mekaoui, Nour; Karboubi, Lamia; Mahraoui, Chafiq; Dakhama, Badr Sououd Benjelloun

2017-01-01

Introduction Les pathologies respiratoires représentent un motif fréquent d'hospitalisation en pédiatrie. L'objectif de cette étude était d'évaluer le profil épidémiologique des pathologies respiratoires chez l'enfant à l'hôpital d'enfants de Rabat, Maroc. Méthodes Il s'agit d'une étude observationnelle transversale qui a concerné tous les cas d'enfants âgés de 3 mois à 15 ans hospitalisés pour une pathologie respiratoire au service de pneumoallergologie et infectiologie pédiatriques de l'hôpital d'enfants de Rabat sur une période d'une année, du 1 janvier 2014 au 31 décembre 2014. Résultats Sur 3537 patients hospitalisés, 2493 (70,5%) l'ont été pour une pathologie respiratoire. Les hospitalisations pour exacerbation d'asthme (p < 0,001), bronchiolite aigüe (p < 0,001) et dyspnée laryngée (p = 0,004) étaient plus fréquentes chez le garçon alors que les hospitalisations pour pneumopathie aigüe (p = 0,005), pour inhalation de corps étranger (p = 0,007) et pour coqueluche (p = 0,020) étaient plus fréquentes chez la fille. Les hospitalisations pour pneumopathie aigüe (p < 0,001), exacerbation de séquelles graves de virose (p < 0,001) et pour coqueluche (p < 0,001) étaient plus fréquentes chez le nourrisson. Les hospitalisations pour pneumopathie aigüe (p < 0,001) et pour coqueluche (p = 0,015) étaient plus fréquentes en période automnohivernale. Conclusion Les motifs d'hospitalisation étaient dominés par les exacerbations d'asthme et la bronchiolite aigüe, lesquelles étaient plus fréquentes chez le garçon. Les infections respiratoires, représentées par les pneumopathies aigües et la coqueluche, étaient plus fréquentes en période automnohivernale et touchaient plus le nourrisson. PMID:29675122

40 CFR 63.7710 - What are my operation and maintenance requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... gases from mold vents in pouring areas and pouring stations that use a sand mold system. This operation... including quality assurance procedures. (iv) How the bag leak detection system will be maintained including...) Procedures for providing an ignition source to mold vents of sand mold systems in each pouring area and...

Singaporean college students overpour drinks similar to Western populations: influence of peer presence in a simulated alcohol-pouring task.

PubMed

Zandy, Shannon L; Pang, Joyce S; Ho, Moon-Ho Ringo; Matthews, Douglas B

2013-11-01

College drinking is a global health concern. However, most studies originate from countries with high alcohol consumption. In the United States, college students overpour a standard alcoholic drink, yet it is unclear if this remains true in countries with low alcohol consumption. Additionally, in college, peer influence is the greatest predictor of drinking behavior, yet it is unknown if social norms affect how students pour drinks. This study examined how male college students, in a country with low alcohol consumption, define standard drinks, and if the presence of an unfamiliar peer affects how students pour during a simulated alcohol-pouring task. Male undergraduate students (n = 105) underwent baseline assessments of impulsivity, self-monitoring, religiosity, and drinking characteristics. Participants poured fluid into empty cups of different sizes to equal a standard serving of beer or shot of liquor. There were 2 groups based on gender of experimenter. Within each group, participants were randomly assigned to Alone or Dyad condition. In the Alone condition, students were instructed to pour only for themselves. In the Dyad condition, students were instructed to pour for themselves and the experimenter. The volumes poured by the students were compared with standards used in Singapore and the United States. Collapsed across container size, students overpoured shots by 50% and beer by 100% when compared to the standard drink definition in Singapore. When using a more liberal definition, students overpoured beer by 25%, but did not overpour shots. In the presence of an unfamiliar peer, overpouring decreased by 10% for beer. The current data show that college students, in a country with low alcohol consumption, overestimate standard alcoholic drinks similar to their Western counterparts and use social norms to determine how much to pour for a drink when confronted with an unfamiliar peer. Efforts toward creating internationally recognized standard drink definitions should be considered. Copyright © 2013 by the Research Society on Alcoholism.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.

The U.S. Department of Energy (DOE), Office of Environmental Management (EM) is sponsoring an international, collaborative project to develop a fundamental model for sulfate solubility in nuclear waste glass. The solubility of sulfate has a significant impact on the achievable waste loading for nuclear waste forms within the DOE complex. These wastes can contain relatively high concentrations of sulfate, which has low solubility in borosilicate glass. This is a significant issue for low-activity waste (LAW) glass and is projected to have a major impact on the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Sulfate solubility has also been amore » limiting factor for recent high level waste (HLW) sludge processed at the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF). The low solubility of sulfate in glass, along with melter and off-gas corrosion constraints, dictate that the waste be blended with lower sulfate concentration waste sources or washed to remove sulfate prior to vitrification. The development of enhanced borosilicate glass compositions with improved sulfate solubility will allow for higher waste loadings and accelerate mission completion.The objective of the current scope being pursued by SHU is to mature the sulfate solubility model to the point where it can be used to guide glass composition development for DWPF and WTP, allowing for enhanced waste loadings and waste throughput at these facilities. A series of targeted glass compositions was selected to resolve data gaps in the model and is identified as Stage III. SHU fabricated these glasses and sent samples to SRNL for chemical composition analysis. SHU will use the resulting data to enhance the sulfate solubility model and resolve any deficiencies. In this report, SRNL provides chemical analyses for the Stage III, simulated HLW glasses fabricated by SHU in support of the sulfate solubility model development.« less

8. INTERIOR VIEW, LOOKING WEST, WITH GREY IRON HOLDING FURNACES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. INTERIOR VIEW, LOOKING WEST, WITH GREY IRON HOLDING FURNACES AND AN IRON POUR IN PROCESS, CUPOLA TENDER RICHARD SLAUGHTER SUPERVISING THE POUR. MOLTEN DUCTILE IRON IS POURED FROM THIS 25-TON HOLDING FURNACE INTO LADLES FOR TRANSPORT TO CASTING STATIONS. - Stockham Pipe & Fittings Company, Grey Iron Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

40 CFR 464.35 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... metal are poured per year, and to plants that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year. PSES Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average kg/1,000 kkg (pounds per million pounds) of metal poured Copper (T) 0.0129 0.0071...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2010 CFR

2010-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2014 CFR

2014-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2012 CFR

2012-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2011 CFR

2011-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

29 CFR Appendix II to Part 1918 - Tables for Selected Miscellaneous Auxiliary Gear (Mandatory)

Code of Federal Regulations, 2013 CFR

2013-07-01

... (IWRC), use vales in HT (FC) columns. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1... HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Notes: (1) These... values in HT columns of Table 3. MS=Mechanical Splice. S=Poured Socket or Swaged Socket. Note: (1) These...

Synthesis copolymer use to reduce pour point temperature of diamond crude oil

NASA Astrophysics Data System (ADS)

Than, Dao Viet; Chuong, Thai Hong; Tuy, Dao Quoc

2017-09-01

Diamond oil field is located in Block 01&02 Offshore Vietnam. Crude oil from Diamond Well Head Platform (WHP) is evacuated to FPSO via 20km 10" subsea flexible pipeline. The lowest seabed temperature in the field is 22°C, while the pour point temperature (PPT) of Diamond crude oil is very high (36°C) due to high paraffin content (25%). So studying to research a suitable Pour Point Depressant (PPD) for the crude oil is very important. The PPD must have ability to reduce pour point temperature of crude oil from 36°C to 21°C.

The "ouzo effect", recent developments and application to therapeutic drug carrying

NASA Astrophysics Data System (ADS)

Botet, Robert

2012-03-01

This short review is about the spontaneous emulsification effect, aka the "ouzo effect". Under certain conditions, pouring a mixture ol a totally water-miscible solvent and a hydrophobic oil into water, generates spontaneously nanometric droplets which are stable, even without surfactant. A basic example is anise-flavored aperitif, which is known from ages in South Europe and North Africa. Then, it is an amazingly old topic, potentially important in a number of applications - such as food additives, paints, cosmetic products or pharmaceutic drugs -, though the main mechanisms are yet essentially unexplained. This phenomenon is presently under intensive investigation using both microfluidic experiments and large-scale numerical simulations, through a CNRS project grouping four laboratories in France. This presentation will give an overview of the history, context and development of the ouzo effect, as well as recent advancements and ideas in the field. This unique effect is now related to two major streams of the scientific research, namely: nano-technology and bio-technology. Consequences in the latter domain is outlined.

Structuring Broadcast Audio for Information Access

NASA Astrophysics Data System (ADS)

Gauvain, Jean-Luc; Lamel, Lori

2003-12-01

One rapidly expanding application area for state-of-the-art speech recognition technology is the automatic processing of broadcast audiovisual data for information access. Since much of the linguistic information is found in the audio channel, speech recognition is a key enabling technology which, when combined with information retrieval techniques, can be used for searching large audiovisual document collections. Audio indexing must take into account the specificities of audio data such as needing to deal with the continuous data stream and an imperfect word transcription. Other important considerations are dealing with language specificities and facilitating language portability. At Laboratoire d'Informatique pour la Mécanique et les Sciences de l'Ingénieur (LIMSI), broadcast news transcription systems have been developed for seven languages: English, French, German, Mandarin, Portuguese, Spanish, and Arabic. The transcription systems have been integrated into prototype demonstrators for several application areas such as audio data mining, structuring audiovisual archives, selective dissemination of information, and topic tracking for media monitoring. As examples, this paper addresses the spoken document retrieval and topic tracking tasks.

65th birthday Jack Steinberger

ScienceCinema

None

2017-12-09

Laudatio pour Jack Steinberger né le 25 mai 1921, à l'occasion de son 65me anniversaire et sa retraite officielle, pour sa précieuse collaboration au Cern. Néanmoins son principal activité continuera comme avant dans sa recherche au Cern. Plusieurs orateurs prennent la parole (p.ex. E.Picasso) pour le féliciter et lui rendre hommage

Matériaux pour la dépollution des gaz d'échappement automobile

NASA Astrophysics Data System (ADS)

Mouaddib-Moral, N.; Gauthier, C.

2002-04-01

Les premières législations antipollution ont été mises en place suite à la détection, aux Etats Unis plus particulièrement en Californie, du smog photochimique et des pluies acides, néfastes pour la faune et la flore. Les estimations de la contribution de l'automobile aux émissions de composés, considérés comme précurseurs de ces phénomènes, ont été suffisantes pour provoquer la mise en place de normes draconiennes en matière d'émissions automobiles. Les matériaux catalytiques ont été évalués en tant que solution possible pour réduire les émissions à l'échappement. En Europe, l'utilisation des catalyseurs trois voies a été généralisée sur les véhicules essence fonctionnant à richesse stoechiométrique à partir de 1993. Une nouvelle génération de catalyseurs appelée piège à oxydes d'azote (NOx) est maintenant nécessaire pour le post-traitement des gaz d'échappement des motorisations à essence fonctionnant en mélange pauvre (combustion en présence d'un excès d'oxygène) pour diminuer la consommation et par conséquent réduire les émissions du CO2 connu pour son impact sur l'effet de serre. La dépollution des moteurs diesel via un catalyseur d'oxydation a été généralisée en Europe depuis 1996. La sévérisation des normes européennes impose pour les moteurs diesel le recours à des matériaux spécifiques pour le traitement des oxydes d'azotes et des particules par l'intermédiaire de filtres à particules dont l'efficacité de filtration est supérieure à 95%, mais doivent subir des régénérations périodiques.

Developpement d'une methode de Monte Carlo dependante du temps et application au reacteur de type CANDU-6

NASA Astrophysics Data System (ADS)

Mahjoub, Mehdi

La resolution de l'equation de Boltzmann demeure une etape importante dans la prediction du comportement d'un reacteur nucleaire. Malheureusement, la resolution de cette equation presente toujours un defi pour une geometrie complexe (reacteur) tout comme pour une geometrie simple (cellule). Ainsi, pour predire le comportement d'un reacteur nucleaire,un schema de calcul a deux etapes est necessaire. La premiere etape consiste a obtenir les parametres nucleaires d'une cellule du reacteur apres une etape d'homogeneisation et condensation. La deuxieme etape consiste en un calcul de diffusion pour tout le reacteur en utilisant les resultats de la premiere etape tout en simplifiant la geometrie du reacteur a un ensemble de cellules homogenes le tout entoure de reflecteur. Lors des transitoires (accident), ces deux etapes sont insuffisantes pour pouvoir predire le comportement du reacteur. Comme la resolution de l'equation de Boltzmann dans sa forme dependante du temps presente toujours un defi de taille pour tous types de geometries,un autre schema de calcul est necessaire. Afin de contourner cette difficulte, l'hypothese adiabatique est utilisee. Elle se concretise en un schema de calcul a quatre etapes. La premiere et deuxieme etapes demeurent les memes pour des conditions nominales du reacteur. La troisieme etape se resume a obtenir les nouvelles proprietes nucleaires de la cellule a la suite de la perturbation pour les utiliser, au niveau de la quatrieme etape, dans un nouveau calcul de reacteur et obtenir l'effet de la perturbation sur le reacteur. Ce projet vise a verifier cette hypothese. Ainsi, un nouveau schema de calcul a ete defini. La premiere etape de ce projet a ete de creer un nouveau logiciel capable de resoudre l'equation de Boltzmann dependante du temps par la methode stochastique Monte Carlo dans le but d'obtenir des sections efficaces qui evoluent dans le temps. Ce code a ete utilise pour simuler un accident LOCA dans un reacteur nucleaire de type CANDU-6. Les sections efficaces dependantes du temps ont ete par la suite utilisees dans un calcul de diffusion espace-temps pour un reacteur CANDU-6 subissant un accident de type LOCA affectant la moitie du coeur afin d'observer son comportement durant toutes les phases de la perturbation. Dans la phase de developpement, nous avons choisi de demarrer avec le code OpenMC, developpe au MIT,comme plateforme initiale de developpement. L'introduction et le traitement des neutrons retardes durant la simulation ont presente un grand defi a surmonter. Il est important de noter que le code developpe utilisant la methode Monte Carlo peut etre utilise a grande echelle pour la simulation de tous les types des reacteurs nucleaires si les supports informatiques sont disponibles.

Modélisation des conséquences possibles de la future demande bioénergétique mondiale pour le bois et les forêts en France

Treesearch

Joseph Buongiorno; Ronald Raunikar; Shusuai Zhu

2011-01-01

L’accroissement de la demande mondiale et du coût correspondant de l’énergie a conduit à de nombreuses propositions pour augmenter l’utilisation de la biomasse renouvelable. Une étude récente (Raunikar et al., 2010) a examiné les conséquences mondiales pour le bois et pour les forêts de la demande en bioénergie impliquée par les scénarios du Groupe d’experts...

Helium High Pressure Tanks at EADS Space Transportation New Technology with Thermoplastic Liner

DTIC Science & Technology

2005-07-13

l’art actuel pour l’application d’un liner thermoplastique sur le réservoir hélium 300 litres pour le lanceur ARIANE 5, réservoir actuellement réalisé à...L à liner thermoplastique ont complètement démontré le respect aux exigences majeures demandées pour le lanceur A5. Ces travaux finalisent la phase

40 CFR 464.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting... million pounds) of metal poured Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO...

40 CFR 464.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting... million pounds) of metal poured Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO...

AGARD/SMP Review Damage Tolerance for Engine Structures. 2. Defects and Quantitative Materials Behaviour

DTIC Science & Technology

1988-10-01

TURBISTAN). En ce qui concerne les materiaux pour aubes de turbine la question reste ouverte. La caracterisation des materiaux pour... caracterisation mecanique. Face aux couts des caracterisations et qualifications de materiaux pour disques de lurbomachines, il importe de tenter...de concentrer ses propres forces : une solution possible est de constituer des plans standard de caracterisation . Federer au sein d’un groupe de

Investigation of pouring temperature and holding time for semisolid metal feedstock production

NASA Astrophysics Data System (ADS)

Razak, N. A.; Ahmad, A. H.; Rashidi, M. M.

2017-10-01

Semisolid metal (SSM) processing, as a kind of new technology that exploits forming of alloys between solidus and liquidus temperatures, has attracted great attention from investigators for its thixotropic behaviour as well as having advantages in reducing porosity, macrosegregation, and forming forces during shaping process. Various techniques are employed to produce feedstock with fine globular microstructures, and direct thermal method is one of them. In this paper, the effect from different pouring temperatures and holding times using a direct thermal method on microstructure and hardness of aluminium alloy 6061 is presented. Molten aluminium alloy 6061 was poured into a cylindrical copper mould and cooled down to the semisolid temperature before being quenched in water at room temperature. The effect of different pouring temperatures of 660 °C, 680 °C, 700 °C, and holding time of 20 s, and 60 s on the microstructure of aluminium alloy 6061 were investigated. From the micrographs, it was found that the most globular structures were achieved at processing parameters of 660 °C pouring temperature and 60 s holding time. The highest density and hardness of the samples were found at the same processing parameters. It can be concluded that the most spheroidal microstructure, the highest density, and the hardness were recorded at lower pouring temperature and longer holding time.

Elastomeric impression materials: a comparison of accuracy of multiple pours.

PubMed

Kumar, Dheeraj; Madihalli, Anand U; Reddy, K Rajeev Kumar; Rastogi, Namrataa; Pradeep, N T

2011-07-01

The aim of the present study is to compare the various elastomeric impression materials in terms of accuracy and dimensional stability, with respect to obtaining multiple casts from a single elastomeric impression at various times of pours. Three master dies were prepared for the impression making, two of these were made of brass containing a central hole with undercuts. The third die simulated a conventionally prepared typodont maxillary central incisor. Three elastomeric impression materials were chosen for the study. Each impression was poured at various time periods. Casts thus obtained were evaluated under a traveling microscope to evaluate various dimensional changes. Addition silicones provided dies which were shorter in height and bigger in diameter. Polyethers provided dies which were shorter in both height and diameter. Condensation silicones showed insignificant changes from the master die at the immediate pour but deteriorated rapidly after that in subsequent pours. None of the impression material showed a consistent behavior up to the fourth pour. They occasionally showed deviation from the pattern, but all these values were statistically insignificant. Polyethers showed lesser ability than both the addition silicones as well as the condensation silicones to recover from induced deformation. Addition silicones as well as the condensation silicones have better ability to recover from induced deformation when compared to polyether.

Large drinks are no mistake: Glass size, but not shape, affects alcoholic beverage drink pours

PubMed Central

Kerr, William C.; Patterson, Deidre; Koenen, Mary Albert; Greenfield, Thomas K.

2009-01-01

Introduction and Aims Drink alcohol content has been shown to be variable and is an important determinant of alcohol intake. This study evaluates claims regarding the effects of glass size and glass shape on the amount of alcohol in on-premise drinks. Design and Methods Wine and spirits drinks were purchased and measured in 80 on-premise establishments in 10 Northern California Counties. Drink alcohol content was measured as the liquid volume of the drink multiplied by the percentage alcohol by volume of given brands or from analysis of mixed drink and wine samples. Results Larger glass size was associated with larger on-premise pours of straight shots and mixed drinks served in the relatively large pint glass and variable “other” glass type were found to contain more alcohol than drinks served in a short wide glass. No significant differences were found for other drink types. Drinks poured in short wide glasses were not found to contain more alcohol than drinks poured in tall thin glasses. Bars with mostly black patrons were found to serve spirits drinks with more alcohol than bars with other patron types. Discussion and Conclusions Glass shape does not affect actual drink pours in the US but glass size does in some cases. Drinkers should measure wine and spirits pours at home to achieve standard drink amounts and consumer education programs should foster awareness of the relatively high drink alcohol content of on-premise wine and mixed spirits drinks. More research is needed to evaluate potential differences in drink pours by patron race and ethnicity. PMID:19594789

Premature melt solidification during mold filling and its influence on the as-cast structure

NASA Astrophysics Data System (ADS)

Wu, M.; Ahmadein, M.; Ludwig, A.

2018-03-01

Premature melt solidification is the solidification of a melt during mold filling. In this study, a numerical model is used to analyze the influence of the pouring process on the premature solidification. The numerical model considers three phases, namely, air, melt, and equiaxed crystals. The crystals are assumed to have originated from the heterogeneous nucleation in the undercooled melt resulting from the first contact of the melt with the cold mold during pouring. The transport of the crystals by the melt flow, in accordance with the socalled "big bang" theory, is considered. The crystals are assumed globular in morphology and capable of growing according to the local constitutional undercooling. These crystals can also be remelted by mixing with the superheated melt. As the modeling results, the evolutionary trends of the number density of the crystals and the volume fraction of the solid crystals in the melt during pouring are presented. The calculated number density of the crystals and the volume fraction of the solid crystals in the melt at the end of pouring are used as the initial conditions for the subsequent solidification simulation of the evolution of the as-cast structure. A five-phase volume-average model for mixed columnar-equiaxed solidification is used for the solidification simulation. An improved agreement between the simulation and experimental results is achieved by considering the effect of premature melt solidification during mold filling. Finally, the influences of pouring parameters, namely, pouring temperature, initial mold temperature, and pouring rate, on the premature melt solidification are discussed.

Revetements antireflet-passivation a base de nitrure de silicium PECVD pour cellules solaires triple-jonction III-V/ Ge

NASA Astrophysics Data System (ADS)

Homier, Ram

Dans le contexte environnemental actuel, le photovoltaïque bénéficie de l'augmentation des efforts de recherche dans le domaine des énergies renouvelables. Pour réduire le coût de la production d'électricité par conversion directe de l'énergie lumineuse en électricité, le photovoltaïque concentré est intéressant. Le principe est de concentrer une grande quantité d'énergie lumineuse sur des petites surfaces de cellules solaires multi-jonction à haute efficacité. Lors de la fabrication d'une cellule solaire, il est essentiel d'inclure une méthode pour réduire la réflexion de la lumière à la surface du dispositif. Le design d'un revêtement antireflet (ARC) pour cellules solaires multi-jonction présente des défis à cause de la large bande d'absorption et du besoin d'égaliser le courant produit par chaque sous-cellule. Le nitrure de silicium déposé par PECVD en utilisant des conditions standards est largement utilisé dans l'industrie des cellules solaires à base de silicium. Cependant, ce diélectrique présente de l'absorption dans la plage des courtes longueurs d'onde. Nous proposons l'utilisation du nitrure de silicium déposé par PECVD basse fréquence (LFSiN) optimisé pour avoir un haut indice de réfraction et une faible absorption optique pour l'ARC pour cellules solaires triple-jonction III-V/Ge. Ce matériau peut aussi servir de couche de passivation/encapsulation. Les simulations montrent que l'ARC double couche SiO2/LFSiN peut être très efficace pour réduire les pertes par réflexion dans la plage de longueurs d'onde de la sous-cellule limitante autant pour des cellules solaires triple-jonction limitées par la sous-cellule du haut que pour celles limitées par la sous-cellule du milieu. Nous démontrons aussi que la performance de la structure est robuste par rapport aux fluctuations des paramètres des couches PECVD (épaisseurs, indice de réfraction). Mots-clés : Photovoltaïque concentré (CPV), cellules solaires multi-jonction (MJSC), revêtement antireflet (ARC), passivation des semiconducteurs III-V, nitrure de silicium (Si"Ny), PECVD.

Ablation laser pour la microélectronique plastique

NASA Astrophysics Data System (ADS)

Alloncle, A.-P.; Thomas, B.; Grojo, D.; Delaporte, Ph.; Sentis, M.; Sanaur, S.; Barret, M.; Collot, Ph.

2006-12-01

La microélectronique plastique connaît un développement sans précédent dans le domaine de la recherche. Cette étude s'intéresse à l'utilisation des lasers impulsionnels pour la réalisation de composants organiques sur supports souples. Les deux aspects plus particulièrement étudiés sont d'une part la gravure de polymère pour réaliser un canal entre la source et le drain, et d'autre part le développement d'un procédéde dépôt appelé LIFT pour Laser Induced Forward Transfer. Ce dernier pourrait notamment permettre dedéposer des composés organiques non solubles.

Spectroscopie pompe-sonde pour la détection de bioaérosols

NASA Astrophysics Data System (ADS)

Guyon, L.; Courvoisier, F.; Wood, V.; Boutou, V.; Bartelt, A.; Roth, M.; Rabitz, H.; Wolf, J. P.

2006-10-01

La fluorescence du Tryptophane excité par une impulsion ultra-brève à 270 nm peut être diminuée d'un facteur deux par une seconde impulsion à 800 nm, à l'aide d'un dispositif pompe-sonde. Cette décroissance est aussi observée pour les bactéries vivantes, dont le Tryptophane est l'un des fluorophores, tandis qu'aucune décroissance n'est observée pour d'autres molécules organiques comme le naphtalène ou le gazole, malgré des spectres d'absorption et de fluorescence similaires. Cette différence remarquable est très prometteuse pour la distinction d'aérosols biologiques et organiques.

Tests sérologiques dans la maladie cœliaque

PubMed Central

Rashid, Mohsin; Lee, Jennie

2016-01-01

Résumé Objectif Répondre aux questions souvent posées par les généralistes et aux difficultés auxquelles ils font face lorsqu’ils prescrivent des tests sérologiques pour la maladie cœliaque et fournir des conseils pratiques pour aider à interpréter les résultats des tests. Sources de l’information Une recherche a été effectuée dans MEDLINE pour les lignes directrices sur le diagnostic et la prise en charge de la maladie cœliaque publiées en anglais entre 2000 et 2015 par des organisations professionnelles de gastro-entérologie. Message principal Pour dépister la maladie cœliaque, le dosage de l’anticorps immunoglobuline A (IgA) anti-transglutaminase tissulaire est le test de choix. Il faut mesurer le taux sérique d’IgA totale afin d’écarter un déficit sélectif en IgA et d’éviter les faux négatifs. Les patients dont le test sérologique est positif doivent être recommandés à un gastro-entérologue pour subir des biopsies de l’intestin grêle par endoscopie afin de confirmer le diagnostic. Le typage des antigènes des leucocytes humains DQ2 et DQ8 peut aider à écarter le diagnostic. Un régime sans gluten ne doit pas être entrepris avant que le diagnostic de maladie cœliaque soit confirmé. Conclusion Les tests sérologiques sont très utiles pour confirmer les soupçons d’une maladie cœliaque. Le diagnostic précoce est essentiel pour prévenir les complications liées à la maladie cœliaque.

Influence du comportement des accompagnants sur le vécu des patients admis pour hémorragies digestives hautes au CHU campus de Lomé (Togo)

PubMed Central

Bagny, Aklesso; Dusabe, Angelique; Bouglouga, Oumboma; Lawson-ananisoh, Mawuli Late; Kaaga, Yeba Laconi; Djibril, Mohaman Awalou; Soedje, Kokou Mensah; Dassa, Simliwa Kolou; Redah, Datouda

2014-01-01

Introduction L'hémorragie digestive haute est une urgence, qui constitue souvent pour les patients un danger mortel suscitant inquiétude et agitation. Dans cet état, le patient dépend de ses accompagnants pour ses soins et pour honorer le traitement; mais souvent, il a été observé une discordance entre l'urgence et les comportements des accompagnants. Le but de cette étude était de décrire les facteurs socioéconomiques et psychologiques pouvant influencer les comportements des accompagnants des patients admis pour HDH, estimer l'indice de relation entre ces comportements et les facteurs associés d'une part et le vécu des patients admis pour HDH d'autre part. Méthodes Il s'agit d'une étude prospective menée de Septembre 2010 à Juin 2011 (soit 10 mois). Nous avions utilisé l'entretien semi-dirigé et l'observation directe pour collecter nos données, ces dernières avaient été traitées par les méthodes statistiques et d'analyse de contenu. Résultats Dans la présente étude, les comportements des accompagnants des patients admis pour HDH sont en majorité marqués par l'abandon (84%) et le manque de sollicitude (80,2%). Ces comportements sont souvent stimulés par les facteurs socioéconomiques tels que les difficultés économiques (83,2%), des conflits intrafamiliaux (85,1%) et des représentations (maladie incurable ou envoûtement) de la maladie par les accompagnants (73,3%) des cas. Quant aux patients, ils vivent ces comportements comme étant des menaces de mort ou des rejets (77,20%) et comme étant une dévalorisation ou une humiliation de la part de leurs accompagnants (70,30%). Les résultats confirment l'existence de lien significatif entre les comportements des accompagnants et les facteurs socio économiques, entre les comportements des accompagnants et des facteurs psychologiques, et entre le vécu des patients admis pour l'HDH et les comportements des accompagnants. Conclusion Des études ultérieures devraient aborder les points non touchés dans cette étude. Certes, elle a apporté un plus dans la compréhension du vécu des patients admis pour HDH et des comportements de leurs accompagnants. Cependant, elle est loin d'avoir épuisé les différents contours de la problématique de la présente étude. PMID:25848453

Gestion des ressources hydriques adaptee aux changements climatiques pour la production optimale d'hydroelectricite. Etude de cas: Bassin versant de la riviere Manicouagan

NASA Astrophysics Data System (ADS)

Haguma, Didier

Il est dorenavant etabli que les changements climatiques auront des repercussions sur les ressources en eau. La situation est preoccupante pour le secteur de production d'energie hydroelectrique, car l'eau constitue le moteur pour generer cette forme d'energie. Il sera important d'adapter les regles de gestion et/ou les installations des systemes hydriques, afin de minimiser les impacts negatifs et/ou pour capitaliser sur les retombees positives que les changements climatiques pourront apporter. Les travaux de la presente recherche s'interessent au developpement d'une methode de gestion des systemes hydriques qui tient compte des projections climatiques pour mieux anticiper les impacts de l'evolution du climat sur la production d'hydroelectricite et d'etablir des strategies d'adaptation aux changements climatiques. Le domaine d'etude est le bassin versant de la riviere Manicouagan situe dans la partie centrale du Quebec. Une nouvelle approche d'optimisation des ressources hydriques dans le contexte des changements climatiques est proposee. L'approche traite le probleme de la saisonnalite et de la non-stationnarite du climat d'une maniere explicite pour representer l'incertitude rattachee a un ensemble des projections climatiques. Cette approche permet d'integrer les projections climatiques dans le probleme d'optimisation des ressources en eau pour une gestion a long terme des systemes hydriques et de developper des strategies d'adaptation de ces systemes aux changements climatiques. Les resultats montrent que les impacts des changements climatiques sur le regime hydrologique du bassin de la riviere Manicouagan seraient le devancement et l'attenuation de la crue printaniere et l'augmentation du volume annuel d'apports. L'adaptation des regles de gestion du systeme hydrique engendrerait une hausse de la production hydroelectrique. Neanmoins, une perte de la performance des installations existantes du systeme hydrique serait observee a cause de l'augmentation des deversements non productibles dans le climat futur. Des strategies d'adaptation structurale ont ete analysees pour augmenter la capacite de production et la capacite d'ecoulement de certaines centrales hydroelectriques afin d'ameliorer la performance du systeme. Une analyse economique a permis de choisir les meilleures mesures d'adaptation et de determiner le moment opportun pour la mise en oeuvre de ces mesures. Les resultats de la recherche offrent aux gestionnaires des systemes hydriques un outil qui permet de mieux anticiper les consequences des changements climatiques sur la production hydroelectrique, incluant le rendement de centrales, les deversements non productibles et le moment le plus opportun pour inclure des modifications aux systemes hydriques. Mots-cles : systemes hydriques, adaptation aux changements climatiques, riviere Manicouagan

Building Resilient Communities Workshop Report

DTIC Science & Technology

2014-06-01

Reine (en droit du Canada), telle que représentée par le ministre de la Défense nationale, 2014 CSSP-2013-CD-1120...EMBC) [ Gestion des urgences Colombie-Britannique], le Programme canadien pour la sûreté et la sécurité (PCSS) et Recherche et développement pour la ...comptes rendus de la mise à jour du rapport du RCERD sur la résilience des communautés autochtones. L’événement a aussi donné une tribune pour un groupe

Behavior Characteristics of Type I (75/25) Octol during Melt Pouring HE Warhead M250 (Chaparral)

DTIC Science & Technology

1979-09-01

COVERED BEHAVIOR CHARACTERISTICS OF TYPE 1 (75/25) "OCTOL DURING MELT POURING HE WARHEAD I M250 (CHAPARRAL) 6. PERFORMING ORG. APrPORT NUMBER 7. AUTHOR...Military Specification, HMX, MIL-H-45444B, Amendment 2, dated 12 July 1977. 4 6. Military Specification, Warhead, Guided Missile, HE, M250 , Loading...CHARACTERISTICS OF TYPE i (75/25) OCTOL DURING MELT POURING HE WARHEAD M250 (CHAPARRAL) HERMAN J. FRIGAND SEPTEMBER 1979 US ARMY ARMAMENT RESEARCH AND

Urban Combat Advanced Training Technology Architecture (Architecture de technologie avancee pour l’entrainement au combat urbain)

DTIC Science & Technology

2018-01-01

REPORT TR-MSG-098 Urban Combat Advanced Training Technology Architecture (Architecture de technologie avancée pour l’entraînement au combat urbain...REPORT TR-MSG-098 Urban Combat Advanced Training Technology Architecture (Architecture de technologie avancée pour l’entraînement au combat...3 1-2 1.3 Illustration of the Need for UCATT by Contemporary Example Situations 1-3 1.3.1 RNLA: Connection of NLD Mobile Combat Training Centre to

Inauguration LEP

ScienceCinema

None

2017-12-09

Le DG C.Rubbia remercie son prédécesseur H.Schopper pour sa contribution pour la réalisation du LEP. En présence du président de la Confédération Suisse, Mons. Délamuraz et du président français Mons.Mitterand plusieurs discours sont donnés et les délégations invités pour un déjeuner.

61. photographer unknown undated FIRST CONCRETE BEING POURED IN DRAFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

61. photographer unknown undated FIRST CONCRETE BEING POURED IN DRAFT TUBE FLOOR SLAB. - Bonneville Project, Powerhouse No.1, Spanning Bradford Slough, from Bradford Island, Bonneville, Multnomah County, OR

Phase II modification of the Water Availability Tool for Environmental Resources (WATER) for Kentucky: The sinkhole-drainage process, point-and-click basin delineation, and results of karst test-basin simulations

USGS Publications Warehouse

Taylor, Charles J.; Williamson, Tanja N.; Newson, Jeremy K.; Ulery, Randy L.; Nelson, Hugh L.; Cinotto, Peter J.

2012-01-01

This report describes Phase II modifications made to the Water Availability Tool for Environmental Resources (WATER), which applies the process-based TOPMODEL approach to simulate or predict stream discharge in surface basins in the Commonwealth of Kentucky. The previous (Phase I) version of WATER did not provide a means of identifying sinkhole catchments or accounting for the effects of karst (internal) drainage in a TOPMODEL-simulated basin. In the Phase II version of WATER, sinkhole catchments are automatically identified and delineated as internally drained subbasins, and a modified TOPMODEL approach (called the sinkhole drainage process, or SDP-TOPMODEL) is applied that calculates mean daily discharges for the basin based on summed area-weighted contributions from sinkhole drain-age (SD) areas and non-karstic topographically drained (TD) areas. Results obtained using the SDP-TOPMODEL approach were evaluated for 12 karst test basins located in each of the major karst terrains in Kentucky. Visual comparison of simulated hydrographs and flow-duration curves, along with statistical measures applied to the simulated discharge data (bias, correlation, root mean square error, and Nash-Sutcliffe efficiency coefficients), indicate that the SDPOPMODEL approach provides acceptably accurate estimates of discharge for most flow conditions and typically provides more accurate simulation of stream discharge in karstic basins compared to the standard TOPMODEL approach. Additional programming modifications made to the Phase II version of WATER included implementation of a point-and-click graphical user interface (GUI), which fully automates the delineation of simulation-basin boundaries and improves the speed of input-data processing. The Phase II version of WATER enables the user to select a pour point anywhere on a stream reach of interest, and the program will automatically delineate all upstream areas that contribute drainage to that point. This capability enables automatic delineation of a simulation basin of any size (area) and having any level of stream-network complexity. WATER then automatically identifies the presence of sinkholes catchments within the simulation basin boundaries; extracts and compiles the necessary climatic, topographic, and basin characteristics datasets; and runs the SDP-TOPMODEL approach to estimate daily mean discharges (streamflow).

Data Package for Secondary Waste Form Down-Selection—Cast Stone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serne, R. Jeffrey; Westsik, Joseph H.

2011-09-05

Available literature on Cast Stone and Saltstone was reviewed with an emphasis on determining how Cast Stone and related grout waste forms performed in relationship to various criteria that will be used to decide whether a specific type of waste form meets acceptance criteria for disposal in the Integrated Disposal Facility (IDF) at Hanford. After the critical review of the Cast Stone/Saltstone literature, we conclude that Cast Stone is a good candidate waste form for further consideration. Cast stone meets the target IDF acceptance criteria for compressive strength, no free liquids, TCLP leachate are below the UTS permissible concentrations andmore » leach rates for Na and Tc-99 are suiteably low. The cost of starting ingredients and equipment necessary to generate Cast Stone waste forms with secondary waste streams are low and the Cast Stone dry blend formulation can be tailored to accommodate variations in liquid waste stream compositions. The database for Cast Stone short-term performance is quite extensive compared to the other three candidate waste solidification processes. The solidification of liquid wastes in Cast Stone is a mature process in comparison to the other three candidates. Successful production of Cast Stone or Saltstone has been demonstrated from lab-scale monoliths with volumes of cm3 through m3 sized blocks to 210-liter sized drums all the way to the large pours into vaults at Savannah River. To date over 9 million gallons of low activity liquid waste has been solidified and disposed in concrete vaults at Savannah River.« less

60. photographer unknown undated CONCRETE BEING POURED ON CENTER PORTION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

60. photographer unknown undated CONCRETE BEING POURED ON CENTER PORTION OF DRAFT TUBE FLOOR SLAB. - Bonneville Project, Powerhouse No.1, Spanning Bradford Slough, from Bradford Island, Bonneville, Multnomah County, OR

Problématique de l'utilisation des Moustiquaires Imprégnées d'insecticide à Longue Durée (MILD) chez les enfants de moins de 5 ans en République Démocratique du Congo

PubMed Central

Philippe, Cilundika Mulenga; Odile, Nyota Nsenga; Numbi, Oscar Luboya

2016-01-01

Introduction Le paludisme est une maladie parasitaire à transmission vectorielle qui constitue un problème majeur de santé publique dans les pays tropicaux, particulièrement les pays de l'Afrique Subsaharienne. La présente étude avait pour objectif d'identifier le niveau d'utilisation de la MILD chez les enfants de moins de 5 ans dans la zone de santé de Mumbunda. Méthodes L’étude, de type transversal, a été mené du 25 au 27 octobre 2013 et a porté sur un échantillon de 410 ménages tirés au hasard et ayant au moins un enfant de moins de 5 ans. Résultats Parmi les ménages qui avaient déclaré possédaient la MILD 13,1% (n=54) des répondant avaient déclaré les utilisé chez les enfants de moins de 5ans et 80,2% pour tout le monde. Dans 22,0% des cas, les répondants ont évoqué le manque d'argent comme motif de la non possession de la MILD. Les répondants savaient déclarer à 79,8% avoir utilisé la MILD pour se protéger contre la malaria et à 66,3% pour se protéger contre les piqures des moustiques. La MILD a été étalée à l'ombre pendant 24h avant d’être utilisée pour la première fois par 77,9% des ménages. Les répondants avaient déclaré à 15,3% (n=63) avoir reçu les conseils par les médias pour l'usage de la moustiquaire. Et le personnel médical était la source la plus importante pour expliquer le mode d'emploi de la MILD pour 51,2% des ménages. Conclusion La réussite pour faire reculer le paludisme doit nécessairement passer par la prévention, le suivi et l’évaluation de l'utilisation des moustiquaires imprégnées au niveau de la zone de santé de Mumbunda. PMID:27222690

Synthese et Caracterisation de Nanocomposites d'Argile et de Graphene Formes a Partir de Precurseurs Organiques =

NASA Astrophysics Data System (ADS)

Boussaboun, Zakariae

Les mineraux d'argile sont des catalyseurs possibles pour la formation du graphene a partir de precurseurs organiques, comme le saccharose. Les argiles sont abondantes, securitaires et economiques pour la formation du graphene. L'objectif principal de ce memoire est de demontrer qu'il est possible de synthetiser un materiau hybride contenant de l'argile et du graphene. La preparation de ces materiaux carbones a base de l'argile (bentonite et cloisite) et le saccharose a ete realisee selon deux methodes. La premiere methode est faite en trois etapes : 1) periode de contact entre l'argile et la source de carbone dans un environnement humide, 2) infiltration de la matiere carbonee et transformation au four a micro-onde, 3) chauffage a 750°C sous azote pour obtenir des materiaux carbones. Par contre la deuxieme methode est faite en deux etapes, sans micro-onde, et avec une augmentation de la quantite de source de carbone (saccharose et alginate). La caracterisation du materiau a permis de suivre les reactions de transformation de la source de carbone vers le graphene. Cette caracterisation a ete faite par la spectroscopie IRTF et Raman, l'analyse thermogravimetrique (TGA), la surface specifique (methode BET) et le microscope electronique a balayage (MEB). La conductivite electrique a ete mesuree par un spectrometre dielectrique et en fonction de la pression appliquee avec un multimetre. Le materiau realise etait incorpore dans une matrice avec un polyethylene a basse densite pour avoir un polymere avec des caracteristiques specifiques. La conductivite thermique a ete ensuite mesuree suivant la norme ASTM E1530. L'echantillon realise avec la deuxieme methode avec une proportion de bentonite pour 5 proportions de saccharose (M2 B1 : S5) signale la possibilite de produire des materiaux de graphene a partir de ressources naturelles. La surface specifique a considerablement augmente de (75,88 m2/g) pour bentonite non traiter a (139,76 m2/g) pour l'echantillon (M2 B1 : S5). Une augmentation significative de la conductivite par pression (95,3 S/m sous une pression de 6,5 MPa par rapport a 1,45*10 -3 S/m pour la bentonite) et la conductivite thermique dans le polyethylene basse densite a une concentration de 10% d'additif (0,332 W/m.K a 0,279 W/m.K) ont ete observes pour le meme echantillon M2 B1 : S5 comparativement a la bentonite non traitee. Les applications possibles sont par exemple les senseurs et les actuateurs par pression.

42. Casting floor, "B" furnace, pour in progress; mudgun is ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. Casting floor, "B" furnace, pour in progress; mudgun is to right of furnace; operator takes temperature of iron in trough during pout. Looking south - Rouge Steel Company, 3001 Miller Road, Dearborn, MI

INTERIOR VIEW WITH LADLE POURING MOLTEN IRON INTO QBOP FURNACE. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW WITH LADLE POURING MOLTEN IRON INTO Q-BOP FURNACE. - U.S. Steel, Fairfield Works, Q-Bop Furnace, North of Valley Road & West of Ensley, Pleasant Grove Road, Fairfield, Jefferson County, AL

Impact of scaling on the nitric-glycolic acid flowsheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D.

Savannah River Remediation (SRR) is considering using glycolic acid as a replacement for formic acid in Sludge Receipt and Adjustment Tank (SRAT) processing in the Defense Waste Processing Facility (DWPF). Catalytic decomposition of formic acid is responsible for the generation of hydrogen, a potentially flammable gas, during processing. To prevent the formation of a flammable mixture in the offgas, an air purge is used to dilute the hydrogen concentration below the 60% of the Composite Lower Flammability Limit (CLFL). The offgas is continuously monitored for hydrogen using Gas Chromatographs (GCs). Since formic acid is much more volatile and toxic thanmore » glycolic acid, a formic acid spill would lead to the release of much larger quantities to the environment. Switching from formic acid to glycolic acid is expected to eliminate the hydrogen flammability hazard leading to lower air purges, thus downgrading of Safety Significant GCs to Process Support GCs, and minimizing the consequence of a glycolic acid tank leak in DWPF. Overall this leads to a reduction in process operation costs and an increase in safety margin. Experiments were completed at three different scales to demonstrate that the nitric-glycolic acid flowsheet scales from the 4-L lab scale to the 22-L bench scale and 220-L engineering scale. Ten process demonstrations of the sludge-only flowsheet for SRAT and Slurry Mix Evaporator (SME) cycles were performed using Sludge Batch 8 (SB8)-Tank 40 simulant. No Actinide Removal Process (ARP) product or strip effluent was added during the runs. Six experiments were completed at the 4-L scale, two experiments were completed at the 22-L scale, and two experiments were completed at the 220-L scale. Experiments completed at the 4-L scale (100 and 110% acid stoichiometry) were repeated at the 22-L and 220-L scale for scale comparisons.« less

Arctic Planning Scenarios: Scenario #1: Defence Scenario

DTIC Science & Technology

2011-07-01

scénarios pour la planification future et d’aider les commandements opérationnels dans leur interaction avec les autres centres d’opérations. Ce rapport...scénarios pour la planification future. Ce rapport présente l’un des scénarios, qui est axé sur une intervention centrée sur la défense. Résultats : Le...et d’autres personnes qui participent à la planification de la défense du Canada auront besoin d’un jeu complet de scénarios pour évaluer les

2010 Coalition Battle Management Language Workshop (Atelier 2010 sur le langage de gestion du champ de bataille pour les operations en coalition)

DTIC Science & Technology

2010-02-01

Feb 2010 2010 Coalition Battle Management Language Workshop (Atelier 2010 sur le langage de gestion du champ de bataille pour les opérations en...RTO MEETING PROCEEDINGS MP-MSG-079 2010 Coalition Battle Management Language Workshop (Atelier 2010 sur le langage de gestion du champ de ...RTO-MP-MSG-079 ES - 3 Atelier 2010 sur le langage de gestion du champ de bataille pour les opérations en coalition (RTO-MP-MSG-079

qPCR (quantitative polymerase chain reaction) for the quantification of bacteriophages in stream water samples to investigate hydrological processes: a proof-of-concept study in the Huewelerbach experimental catchment (Luxembourg)

NASA Astrophysics Data System (ADS)

Antonelli, Marta; Narayanan Balasubramanian, Mukundh; Ogorzaly, Leslie; Pfister, Laurent

2016-04-01

Albeit recent technological developments (e.g. field deployable instruments operating at high temporal frequencies), experimental hydrology is a discipline that remains measurement limited. From this perspective, trans-disciplinary approaches may create valuable opportunities to enlarge the amount of tools available for investigating hydrological processes. Bacteriophages have been widely used in hydrology as biological tracer for investigating colloid transport and contamination of ground water systems. However, there are only a few studies focusing on the employability of bacteriophages as surface water tracers (i.e. phage transport, system functioning). Here, we present a proof-of-concept study carried out in the Huewelerbach catchment in Luxembourg in December 2015. The aim of this study was to investigate how viral particles can be used to detect hydrological connectivity between the riparian zone/river bank and the stream during rainfall events. Moreover, this study is one of the first attempts for applying the qPCR (quantitative polymerase chain reaction) technique for the quantification of bacteriophages in stream water samples to investigate hydrological processes. This technique is very sensitive and has a large dynamic range - enhancing ease and speed of phage detection. We used two different male-specific coliphages (GA phage, genogroup II and SP phage, genogroup IV). Two litres of GA phage were injected directly in the stream as a slug injection and two litres of SP phage were poured next to the river bank (alluvial deposition) close to the injection point. We also added NaCl (200 g) to both phage suspensions. We collected stream water samples 100 m and 500 m downstream (i.e. catchment outlet) of the injection point for one week. Phages were concentrated through ultracentrifugation of 100 ml of water sample followed by quantification via qPCR. Conductivity in stream water was monitored for the entire duration of the experiment. Discharge was monitored both immediately upstream of the injection point and at the catchment outlet. Preliminary results show that at the catchment outlet, the GA-phage injected in stream displayed almost complete mass recovery (~93 %), in contrast to the partial recovery (~12%) of the SP phage that was introduced on the river bank. Additionally, the amount of GA phages detected 100 m downstream of the injection point evolved back to its background level after six days. We could not observe a similar evolution for the SP phage. At the outlet, the amount of both phages did not return to background levels after six days. This can be due to a combined action of the occurrence of preferential flowpaths and the behaviour of colloids. During the monitored rain event we observed a dilution effect on both phages and a slight increase of the quantity of SP phage right after the peak of discharge. This finding suggests a release of viral particles from the river bank. Overall, we have demonstrated with this proof-of-concept study the value of phages as eco-hydrological tracer.

Modelisation de photodetecteurs a base de matrices de diodes avalanche monophotoniques pour tomographie d'emission par positrons

NASA Astrophysics Data System (ADS)

Corbeil Therrien, Audrey

La tomographie d'emission par positrons (TEP) est un outil precieux en recherche preclinique et pour le diagnostic medical. Cette technique permet d'obtenir une image quantitative de fonctions metaboliques specifiques par la detection de photons d'annihilation. La detection des ces photons se fait a l'aide de deux composantes. D'abord, un scintillateur convertit l'energie du photon 511 keV en photons du spectre visible. Ensuite, un photodetecteur convertit l'energie lumineuse en signal electrique. Recemment, les photodiodes avalanche monophotoniques (PAMP) disposees en matrice suscitent beaucoup d'interet pour la TEP. Ces matrices forment des detecteurs sensibles, robustes, compacts et avec une resolution en temps hors pair. Ces qualites en font un photodetecteur prometteur pour la TEP, mais il faut optimiser les parametres de la matrice et de l'electronique de lecture afin d'atteindre les performances optimales pour la TEP. L'optimisation de la matrice devient rapidement une operation difficile, car les differents parametres interagissent de maniere complexe avec les processus d'avalanche et de generation de bruit. Enfin, l'electronique de lecture pour les matrices de PAMP demeure encore rudimentaire et il serait profitable d'analyser differentes strategies de lecture. Pour repondre a cette question, la solution la plus economique est d'utiliser un simulateur pour converger vers la configuration donnant les meilleures performances. Les travaux de ce memoire presentent le developpement d'un tel simulateur. Celui-ci modelise le comportement d'une matrice de PAMP en se basant sur les equations de physique des semiconducteurs et des modeles probabilistes. Il inclut les trois principales sources de bruit, soit le bruit thermique, les declenchements intempestifs correles et la diaphonie optique. Le simulateur permet aussi de tester et de comparer de nouvelles approches pour l'electronique de lecture plus adaptees a ce type de detecteur. Au final, le simulateur vise a quantifier l'impact des parametres du photodetecteur sur la resolution en energie et la resolution en temps et ainsi optimiser les performances de la matrice de PAMP. Par exemple, l'augmentation du ratio de surface active ameliore les performances, mais seulement jusqu'a un certain point. D'autres phenomenes lies a la surface active, comme le bruit thermique, provoquent une degradation du resultat. Le simulateur nous permet de trouver un compromis entre ces deux extremes. Les simulations avec les parametres initiaux demontrent une efficacite de detection de 16,7 %, une resolution en energie de 14,2 % LMH et une resolution en temps de 0.478 ns LMH. Enfin, le simulateur propose, bien qu'il vise une application en TEP, peut etre adapte pour d'autres applications en modifiant la source de photons et en adaptant les objectifs de performances. Mots-cles : Photodetecteurs, photodiodes avalanche monophotoniques, semiconducteurs, tomographie d'emission par positrons, simulations, modelisation, detection monophotonique, scintillateurs, circuit d'etouffement, SPAD, SiPM, Photodiodes avalanche operees en mode Geiger

Advantages and limitations for users of double pit pour-flush latrines: a qualitative study in rural Bangladesh.

PubMed

Hussain, Faruqe; Clasen, Thomas; Akter, Shahinoor; Bawel, Victoria; Luby, Stephen P; Leontsini, Elli; Unicomb, Leanne; Barua, Milan Kanti; Thomas, Brittany; Winch, Peter J

2017-05-25

In rural Bangladesh, India and elsewhere, pour-flush pit latrines are the most common sanitation system. When a single pit latrine becomes full, users must empty it themselves and risk exposure to fresh feces, pay an emptying service to remove pit contents or build a new latrine. Double pit pour-flush latrines may serve as a long-term sanitation option including high water table areas because the pits do not need to be emptied immediately and the excreta decomposes into reusable soil. Double pit pour-flush latrines were implemented in rural Bangladesh for 'hardcore poor' households by a national NGO, BRAC. We conducted interviews, focus groups, and spot checks in two low-income, rural areas of Bangladesh to explore the advantages and limitations of using double pit latrines compared to single pit latrines. The rural households accepted the double pit pour-flush latrine model and considered it feasible to use and maintain. This latrine design increased accessibility of a sanitation facility for these low-income residents and provided privacy, convenience and comfort, compared to open defecation. Although a double pit latrine is more costly and requires more space than a single pit latrine the households perceived this sanitation system to save resources, because households did not need to hire service workers to empty pits or remove decomposed contents themselves. In addition, the excreta decomposition process produced a reusable soil product that some households used in homestead gardening. The durability of the latrine superstructures was a problem, as most of the bamboo-pole superstructure broke after 6-18 months of use. Double pit pour-flush latrines are a long-term improved sanitation option that offers users several important advantages over single pit pour-flush latrines like in rural Bangladesh which can also be used in areas with high water table. Further research can provide an understanding of the comparative health impacts and effectiveness of the model in preventing human excreta from entering the environment.

Endectocide activity of a pour-on formulation containing 1.5 per cent ivermectin +0.5 per cent abamectin in cattle.

PubMed

Silva, Heloisa Cristina; Prette, Nancy; Lopes, Welber Daniel Zanetti; Sakamoto, Cláudio Alessandro M; Buzzulini, Carolina; Dos Santos, Thais Rabelo; Cruz, Breno Cayeiro; Teixeira, Weslen F Pires; Felippelli, Gustavo; Carvalho, Rafael Silveira; Maciel, Willian Giquelin; Soares, Vando Edésio; da Costa, Alvimar José

2015-01-01

The present work aimed to evaluate, through ten different studies, the therapeutic efficacy of a new pour-on formulation, containing 1.5 per cent ivermectin +0.5 per cent abamectin, against parasites of cattle. Results obtained on trials against Rhipicephalus (Boophilus) microplus showed that the pour-on combination of 1.5 per cent ivermectin +0.5 per cent abamectin obtained superior efficacy indexes against this ectoparasite, when compared with formulations containing 0.5 per cent ivermectin, 1 per cent ivermectin and the combination of 1 per cent abamectin +20 per cent levamisole. The results of efficacy of the ivermectin+abamectin and the 0.5 per cent ivermectin against Haematobia irritans were similar. Against Cochliomyia hominivorax larvae, all pour-on formulations tested (1.5 per cent ivermectin +0.5 per cent abamectin, 0.5 per cent ivermectin and 0.5 per cent abamectin), as well as 1 per cent doramectin administered subcutaneously, were considered ineffective. Cattle medicated with 1.5 per cent ivermectin +0.5 per cent abamectin, pour-on, remained free from parasitism by Dermatobia hominis larvae during 42 days (96 per cent efficacy), while values superior to 90 per cent were obtained by 0.5 per cent ivermectin (92 per cent) and 0.5 per cent abamectin (93 per cent) until the 42nd and 35th days post treatment, respectively. Against Haemonchus placei and Oesophagostomum radiatum, the pour-on of ivermectin+abamectin showed better efficacy than the 0.5 per cent ivermectin and 0.5 per cent abamectin. As to Cooperia punctata, there was no difference regarding efficacy results obtained by the avermectins combination and abamectin. The pour-on combination of 1.5 per cent ivermectin +0.5 per cent abamectin obtained high efficacy against R. (B.) microplus, D. hominis and some species of cattle gastrointestinal helminths when compared with formulations of 0.5 per cent ivermectin and 0.5 per cent abamectin administered through the same route.

Dimensions rénales en Service de Néphrologie Clinique, Befelatanana, Antananarivo

PubMed Central

Ramilitiana, Benja; Dodo, Mihary; Rakotoarimanga, Henintsoa Nirina; Randriamboavonjy, Rado Lalao; Randriamarotia, Willy Franck

2016-01-01

La connaissance des dimensions rénales pour tout individu et pour toute ethnie, aide à une décision médicale d'ordre diagnostique et thérapeutique. Pour un pays à faible revenu comme Madagascar, l’échographie constitue un outil idéal à cette fin. Ce travail a comme objectifs de recueillir les dimensions rénales, puis de chercher la corrélation entre ces dernières et les paramètres démographiques ou anthropométriques des Malgaches. Il s'agit d'une étude rétrospective, s’étalant sur une période de 3 ans, effectuée dans le service de Néphrologie du centre hospitalier de Befelatanana, Antananarivo, recrutant 200 patients non diabétiques, sans maladie rénale chronique. L’âge moyen de nos patients était de 45 ans ±16, avec un sex ratio de 0,9. En moyenne, les dimensions (longueur × largeur × épaisseur) étaient de 98 mm × 42 mm × 30 mm pour le rein droit et 99 mm × 45 mm × 31 mm pour le rein gauche. Nous avons retrouvé une différence significative entre le rein droit et gauche sur la longueur (p<0,00001) et la largeur (p = 0,03). Une relation significative était aussi retrouvée entre la longueur rénale et l’âge (p = 0,0016 et p = 0,04 respectivement pour le rein droit et le rein gauche). Aucune relation significative n'a été établie entre les dimensions rénales et la taille ni le poids de nos patients. Malgré ses limites, notre étude apporterait une aide sur le plan pratique clinique ainsi que pour une étude ultérieure. PMID:27642455

A flying hot wire study of the turbulent near wake of a circular cylinder at Reynolds number of 140,000. Ph.D. Thesis. Progress Report

NASA Technical Reports Server (NTRS)

Cantwell, B. J.

1975-01-01

The phenomenology was studied of the processes of vortex formation and transport in the near wake, at a Reynolds number sufficiently high to insure a fully turbulent wake, but low enough to insure a laminar separation. The apparatus developed for measuring this flow consisted of X-array hot wire probes mounted on the ends of a pair of whirling arms. A computer controlled data acquisition system was slaved to the position of the rotating arm and managed, monitored, edited, and recorded the vast profusion of data which is continuously poured out by the device. Results are presented which show the instantaneous velocity, intermittency, vorticity, and stress fields as a function of phase for the first six diameters of the near wake. The stresses in the near wake emerge as a concatenation of peaks and valleys, some the result of strong induced motions in the outer flow which cause free stream fluid to move rapidly inward toward the center of the wake, others the result of the random motions of the background turbulence.

A Workflow to Model Microbial Loadings in Watersheds ...

EPA Pesticide Factsheets

Many watershed models simulate overland and instream microbial fate and transport, but few actually provide loading rates on land surfaces and point sources to the water body network. This paper describes the underlying general equations for microbial loading rates associated with 1) land-applied manure on undeveloped areas from domestic animals; 2) direct shedding on undeveloped lands by domestic animals and wildlife; 3) urban or engineered areas; and 4) point sources that directly discharge to streams from septic systems and shedding by domestic animals. A microbial source module, which houses these formulations, is linked within a workflow containing eight models and a set of databases that form a loosely configured modeling infrastructure which supports watershed-scale microbial source-to-receptor modeling by focusing on animal-impacted catchments. A hypothetical example application – accessing, retrieving, and using real-world data – demonstrates the ability of the infrastructure to automate many of the manual steps associated with a standard watershed assessment, culminating with calibrated flow and microbial densities at the pour point of a watershed. Presented at 2016 Biennial Conference, International Environmental Modelling & Software Society.

The Whole Elephant: A Synoptic View of Liquid Rope Coiling

NASA Astrophysics Data System (ADS)

Ribe, Neil

2016-11-01

Liquid rope coiling is the instability that occurs when e.g. a thin stream of honey is poured onto toast. While we now have a fine-grained understanding of each of the four principal coiling modes (viscous, gravitational, inertio-gravitational and inertial), we still lack a global view of how the modes cohere to form a larger whole. Using a numerical continuation procedure, I determine how the dimensionless coiling frequency depends on the dimensionless fall height and flow rate, for several values of the dimensionless nozzle diameter. Starting with the onset of coiling, I propose a purely geometrical definition of the critical surface between coiling and no coiling as the locus of points where the radius a1 of the rope at the contact point is just equal to the coil radius R. Coiling with a1 > R is impossible because the rope would intersect itself. I characterize the asymptotic limits of the critical surface as well as the structure of the supercritical volume inside that surface. The procedure reveals a new mode of coiling onset that has not yet been identified.

POURING IRON FROM ELECTRIC FURNACE INTO BULL LADLE AFTER MAGNESIUM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

POURING IRON FROM ELECTRIC FURNACE INTO BULL LADLE AFTER MAGNESIUM HAD BEEN ADDED TO GENERATE DUCTILE IRON WHEN IT COOLS IN THE MOLD. - Southern Ductile Casting Company, Casting, 2217 Carolina Avenue, Bessemer, Jefferson County, AL

Validation of hot-poured crack sealant performance-based guidelines.

DOT National Transportation Integrated Search

2017-06-01

This report summarizes a comprehensive research effort to validate thresholds for performance-based guidelines and : grading system for hot-poured asphalt crack sealants. A series of performance tests were established in earlier research and : includ...

6. VIEW LOOKING WEST FROM THE POURING AISLE OF THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW LOOKING WEST FROM THE POURING AISLE OF THE ELECTRIC FURNACE BUILDING AT ELECTRIC FURNACE X-3. - U.S. Steel Duquesne Works, Electric Furnace Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Miroirs multicouches C/SI a incidence normale pour la region spectrale 25-40 nanometres

NASA Astrophysics Data System (ADS)

Grigonis, Marius

Nous avons propose la nouvelle combinaison de materiaux, C/Si, pour la fabrication de miroirs multicouches a incidence normale dans la region spectrale 25-40 nm. Les resultats experimentaux montrent que cette combinaison possede une reflectivite d'environ ~25% dans la region spectrale 25-33 nm et une reflectivite d'environ ~23% dans la region spectrale 33-40 nm. Ces valeurs de reflectivite sont les plus grandes obtenues jusqu'a maintenant dans la region spectrale 25-40 nm. Les miroirs multicouches ont ete par la suite caracterises par microscopie electronique a transmission, par diverses techniques de diffraction des rayons X et par spectroscopies d'electrons AES et ESCA. La resistance des miroirs aux temperatures elevees a ete egalement etudiee. Les resultats fournis par les methodes de caracterisation indiquent que cette combinaison possede des caracteristiques tres prometteuses pour son application comme miroir pour les rayons X mous.

Analyse experimentale des performances d'une batterie au lithium pour l'aeronautique

NASA Astrophysics Data System (ADS)

Bonnin, Romain

Ce memoire a pour objectif d'identifier et d'etudier les performances necessaires pour qu'une batterie au lithium puisse etre utilisee dans le secteur de l'aeronautique. C'est pourquoi dans le cadre de notre recherche, nous allons proposer une procedure de tests permettant d'analyser et de determiner si la batterie au lithium peut etre implantee dans un avion. En vue de repondre a l'analyse des performances, une etude des fonctionnalites demandees par l'avion ainsi que des normes preexistantes vont etre effectuees. Suite a cette etape, nous allons elaborer un banc d'essais. Une fois le banc d'essais acheve, nous allons tester une batterie au lithium qui est supposee disposer de toutes les caracteristiques techniques requises pour etre implantee dans un avion. Ces tests nous permettront donc d'emettre un avis sur l'utilisation des batteries au lithium dans le domaine de l'aeronautique.

More on the losses of dissolved CO(2) during champagne serving: toward a multiparameter modeling.

PubMed

Liger-Belair, Gérard; Parmentier, Maryline; Cilindre, Clara

2012-11-28

Pouring champagne into a glass is far from being inconsequential with regard to the dissolved CO(2) concentration found in champagne. Three distinct bottle types, namely, a magnum bottle, a standard bottle, and a half bottle, were examined with regard to their loss of dissolved CO(2) during the service of successively poured flutes. Whatever the bottle size, a decreasing trend is clearly observed with regard to the concentration of dissolved CO(2) found within a flute (from the first to the last one of a whole service). Moreover, when it comes to champagne serving, the bottle size definitely does matter. The higher the bottle volume, the better its buffering capacity with regard to dissolved CO(2) found within champagne during the pouring process. Actually, for a given flute number in a pouring data series, the concentration of dissolved CO(2) found within the flute was found to decrease as the bottle size decreases. The impact of champagne temperature (at 4, 12, and 20 °C) on the losses of dissolved CO(2) found in successively poured flutes for a given standard 75 cL bottle was also examined. Cold temperatures were found to limit the decreasing trend of dissolved CO(2) found within the successively poured flutes (from the first to the last one of a whole service). Our experimental results were discussed on the basis of a multiparameter model that accounts for the major physical parameters that influence the loss of dissolved CO(2) during the service of a whole bottle type.

Pozzolan cement study : final report.

DOT National Transportation Integrated Search

1979-12-01

An experimental section using Type 1P cement concrete was poured on an active construction project in south Louisiana, near Franklin. A comparison in quality was made between this section and the normal Type 1(B) cement concrete poured on the remaind...

Analyse de L'ancrage des Vortex Intergrains pour le Yttrium BARYUM(2) CUIVRE(3) OXYGENE(7) Polycristallin

NASA Astrophysics Data System (ADS)

Fournier, Patrick

Le Modele de l'Etat Critique Generalise (MECG) est utilise pour decrire les proprietes magnetiques et de transport du YBa_2Cu_3O _7 polycristallin. Ce modele empirique permet de relier la densite de courant critique a la densite de lignes de flux penetrant dans la region intergrain. Deux techniques de mesures sont utilisees pour caracteriser nos materiaux. La premiere consiste a mesurer le champ au centre d'un cylindre creux en fonction du champ magnetique applique pour des temperatures comprises entre 20 et 85K. En variant l'epaisseur de la paroi du cylindre creux, il est possible de suivre l'evolution des cycles d'hysteresis et de determiner des champs caracteristiques qui varient en fonction de cette dimension. En utilisant un lissage des resultats experimentaux, nous determinons J _{co}, H_ {o} et n, les parametres du MECG. La forme des cylindres, avec une longueur comparable au diametre externe, entrai ne la presence d'un champ demagnetisant qui peut etre inclus dans le modele theorique. Ceci nous permet d'evaluer la fraction du volume ecrante, f _{g}, ainsi que le facteur demagnetisant N. Nous trouvons que J_{ co}, H_{o} et f_{g} dependent de la temperature, tandis que n et N (pour une epaisseur de paroi fixe) n'en dependent pas. La deuxieme technique consiste a mesurer le courant critique de lames minces en fonction du champ applique pour differentes temperatures. Nous utilisons un montage que nous avons developpe permettant d'effectuer ces mesures en contact direct avec le liquide refrigerant, i.e. dans l'azote liquide. Nous varions la temperature du liquide en variant la pression du gaz au-dessus du bain d'azote. Cette methode nous permet de balayer des temperatures entre 65K et la temperature critique du materiau ({~ }92K). Nous effectuons le lissage des courbes de courant critique en fonction du champ applique encore a l'aide du MECG, pour a nouveau obtenir ses parametres. Pour trois echantillons avec des traitements thermiques differents, les parametres sont differents confirmant que la variation des proprietes macroscopiques de ces supraconducteurs est intimement reliee a la nature des jonctions entre les grains et de la surface des grains. L'oxygenation prolongee retablit les proprietes initiales des echantillons qui se sont degrades durant le recuit des contacts.

Maximum heat of mass concrete - phase 2 [summary].

DOT National Transportation Integrated Search

2016-12-01

Concrete hardens through a chemical reaction that produces heat and expansion, followed by contraction as the concrete cools. Concrete near the edge of a pour cools faster and shrinks earlier than concrete further from the edge. Most concrete pours a...

Aircraft Disinsection: A Guide for Military and Civilian Air Carriers (Desinsectisation des aeronefs: Un guide a l’intention des responsables des transports aeriens civils et militaires)

DTIC Science & Technology

1996-04-01

regulations. - Ceratitis capitata (Mediterranean fruit fly). Quarantine regulations generally reduce - Rhagoletis pomonella (Apple maggot). the chances of a...d’insectes nuisibles dans un pays, en 6vitant des risques pour la sant6 des 6quipages, pour la s~curit6 de 1’a~ronef et pour l’industrie. Ce rapport examine 1...diffrrents officiels responsables de la r~glementation des insectes nuisibles introduits, de l’inscription des pesticides et de leur utilisation en

Management of Heat and Cold Stress -- Guidance to NATO Medical Personnel (Gestion des contraintes thermiques (chaleur et froid) Conseils aux personnels medicaux de I’OTAN)

DTIC Science & Technology

2013-12-01

de la performance de leurs troupes; b) d’importants écarts scientifiques / de capacités existent en ce qui concerne la susceptibilité, le... La HFM/RTG-187 avait pour but de : a) comparer et évaluer les ressources techniques qui sont actuellement utilisées pour un « système de gestion des ...d’une doctrine et de programmes d’enseignement intégrés pour la gestion des risques thermiques afin de garantir le maintien

Soldiers in Cold Environments (Soldats en environnements froids)

DTIC Science & Technology

2009-04-01

survie par temps froid et en eau froide pour l’essai de divers ensembles d’habillement ; d) envisager l’adoption du procédé d’Ulm pour le traitement des...vêtements d’hiver ; • Les expériences de laboratoire en air froid et sur la morsure du gel; • La modélisation de la survie en eau froide et en air froid...normalisés au sein des pays de l’OTAN ; b) développer un protocole commun pour le traitement de l’hypothermie; c) développer un modèle de prévision de

Special Course on Inverse Methods for Airfoil Design for Aeronautical and Turbomachinery Applications (Methodes Inverses pour la Conception des Profils Porteurs pour des Applications dans les Domaines de l’Aeronautique et des Turbomachines)

DTIC Science & Technology

1990-11-01

engined jet aircraft wing MID PLA CROSS tCTO% taking into account the effects of the propulsive system. -DESIGN PAAMETERS DESTIGE PARAMETERS 5CT 0 (MC 0...AGARD Report No.780 Special Course on Inverse Methods for Airfoil Design for Aeronautical and Turbomachinery Applications (M6thodes Inverses pour la...manufacturing systems. Blade or airfoil designs are normally made in two steps, and the lectures are accordingly grouped into two parts. - - In the

Automated Software Generation Approaches for the Design and Development of Guidance and Control Systems Software (Les Differentes Approches Generation pour la Conception et le Developpement de Logiciels de Guidage et de Pilotage)

DTIC Science & Technology

1992-03-01

de Logiciels") etaient en cours de developpement pour resoudre des problimes similaires dans le monde de la gestion . le Panel... gestion des sp cifications, d’algorithmes et de reprtsentations. Techniques et Sciences Informatiques, 4(3), 1985. 4-21 R. Jacquart, M. Lemoine, and G...Guidance and Control Systems Software (Les Diff~rentes Approches "G6neration" pour la Conception et le D~veloppement de Logiciels de Guidage et de

Internal Blast in a Compartment-type Vessel. Part 1: Finite Element Modeling Investigation

DTIC Science & Technology

2012-11-01

données expérimentales devraient aussi être utilisées pour valider le modèle. DRDC Valcartier TM 2012-222 iii Executive summary Internal...pour simuler adéquatement le souffle d’explosion, incluant le choc et ses réflexions, à l’intérieur d’une large structure et le besoin de remédier à...terme, le développement et la validation d’un ‘raytracer’ et son couplage avec LS-DYNA seront étudiés pour modéliser le choc dans le compartiment

A Statistical Treatment of Bioassay Pour Fractions

NASA Technical Reports Server (NTRS)

Barengoltz, Jack; Hughes, David W.

2014-01-01

The binomial probability distribution is used to treat the statistics of a microbiological sample that is split into two parts, with only one part evaluated for spore count. One wishes to estimate the total number of spores in the sample based on the counts obtained from the part that is evaluated (pour fraction). Formally, the binomial distribution is recharacterized as a function of the observed counts (successes), with the total number (trials) an unknown. The pour fraction is the probability of success per spore (trial). This distribution must be renormalized in terms of the total number. Finally, the new renormalized distribution is integrated and mathematically inverted to yield the maximum estimate of the total number as a function of a desired level of confidence ( P(

Spectrometre de masse a ionisation Penning selective: Elimination des corrections necessaires a la determination du rapport isotopique de l'hydrogene

NASA Astrophysics Data System (ADS)

Letarte, Sylvain

Dans le but d'ameliorer la precision avec laquelle le rapport isotopique de l'hydrogene peut etre determine, un spectrometre de masse a ionisation Penning a ete construit pour provoquer l'ionisation selective de l'hydrogene moleculaire et de l'hydrure de deuterium a partir d'un melange gazeux. L'utilisation d'atomes dans des etats d'excitation metastable s'est averee une solution adequate pour reponde a cette attente. L'emploi de l'helium, a l'interieur d'une source d'atomes metastables construit specifiquement pour ce travail, ne permet pas d'obtenir un spectre de masse compose uniquement des deux molecules d'interet. L'ionisation de ces dernieres provient de deux processus distincts, soient l'ionisation Penning et l'ionisation par bombardement electronique. Contrairement a l'helium, il a ete demontre que le neon metastable est un candidat ideal pour produire l'ionisation selective de type Penning. Le nombre d'ions produits est directement proportionnel au courant de la decharge electrique et de la pression d'operation de la source d'atomes metastables. Ces resultats demontrent le potentiel d'un tel spectrometre de masse pour ameliorer la precision a laquelle le rapport isotopique peut etre determine comparativement aux autres techniques existantes.

Utilisation d'images aeroportees a tres haute resolution spatiale pour l'estimation de la vigueur des peuplements forestiers du nord-ouest du Nouveau-Brunswick

NASA Astrophysics Data System (ADS)

Louis, Ognel Pierre

Le but de cette etude est de developper un outil permettant d'estimer le niveau de risque de perte de vigueur des peuplements forestiers de la region de Gounamitz au nord-ouest du Nouveau-Brunswick via des donnees d'inventaires forestiers et des donnees de teledetection. Pour ce faire, un marteloscope de 100m x 100m et 20 parcelles d'echantillonnages ont ete delimites. A l'interieur de ces derniers, le niveau de risque de perte de vigueur des arbres ayant un DHP superieur ou egal a 9 cm a ete determine. Afin de caracteriser le risque de perte de vigueur des arbres, leurs positions spatiales ont ete repertoriees a partir d'un GPS en tenant compte des defauts au niveau des tiges. Pour mener a bien ce travail, les indices de vegetation et de textures et les bandes spectrales de l'image aeroportee ont ete extraits et consideres comme variables independantes. Le niveau de risque de perte de vigueur obtenu par espece d'arbre a travers les inventaires forestiers a ete considere comme variable dependante. En vue d'obtenir la superficie des peuplements forestiers de la region d'etude, une classification dirigee des images a partir de l'algorithme maximum de vraisemblance a ete effectuee. Le niveau de risque de perte de vigueur par type d'arbre a ensuite ete estime a l'aide des reseaux de neurones en utilisant un reseau dit perceptron multicouches. Il s'agit d'un modele de reseau de neurones compose de : 11 neurones sur la couche d'entree, correspondant aux variables independantes, 35 neurones sur la couche cachee et 4 neurones sur la couche de sortie. La prediction a partir des reseaux de neurones produit une matrice de confusion qui permet d'obtenir des mesures quantitatives d'estimation, notamment un pourcentage de classification globale de 91,7% pour la prediction du risque de perte de vigueur du peuplement de resineux et de 89,7% pour celui du peuplement de feuillus. L'evaluation de la performance des reseaux de neurones fournit une valeur de MSE globale de 0,04, et une RMSE (Mean Square Error) globale de 0,20 pour le peuplement de feuillus. Quant au peuplement de resineux, une valeur de MSE (Mean Square Error) globale de 0,05 et une valeur de RMSE globale de 0,22 ont ete obtenues. Pour la validation des resultats, le niveau de risque de perte de vigueur predit a ete compare avec le risque de perte de vigueur de reference. Les resultats obtenus donnent un coefficient de determination de 0,98 pour le peuplement de feuillus et 0,93 pour le peuplement de resineux.

La prise en charge des troubles de santé mentale par les omnipraticiens du Québec

PubMed Central

Fleury, Marie-Josée; Farand, Lambert; Aubé, Denise; Imboua, Armelle

2012-01-01

Résumé Objectif Cette recherche vise à documenter la prise en charge des troubles mentaux (TM) par les omnipraticiens. Type d’étude Il s’agit d’une étude mixte intégrant un questionnaire auto-administré et des entrevues qualitatives. La banque de données administratives des actes médicaux de la Régie de l’assurance maladie du Québec a aussi été analysée. Contexte La province de Québec. Participants Un total de 1415 omnipraticiens de différents lieux de pratiques ont été sollicités pour le questionnaire; 970 ont été rejoints. Un sous-groupe de 60 omnipraticiens a été rejoint pour les entrevues. Principaux paramètres à l'étude La prévalence annuelle des consultations reliées à des TM courants (TMC) ou graves (TMG), les pratiques cliniques, les pratiques de collaboration, les facteurs facilitant ou entravant la prise en charge des TM, ainsi que les recommandations pour l’amélioration du système de soins. Résultats Le taux de réponse a été de 41% (n = 398 omnipraticiens) pour le questionnaire et de 63% (n = 60) pour les entrevues. Environ 25 % des visites chez les omnipraticiens sont associées à des TM. Presque tous les omnipraticiens prennent en charge des TMC et se sentent compétents pour le faire, à l’inverse de la situation retrouvée pour les TMG. Près de 20 % des TMC sont référés (principalement à des intervenants psychosociaux), alors que près de 75 % des TMG sont référés (surtout en psychiatrie et à l’urgence). Plus de 50 % des omnipraticiens affirment n’entretenir aucun contact avec l’une ou l’autre des ressources de santé mentale. Plusieurs facteurs influencent la prise en charge des TM: les profils des patients (complexité des TM, troubles concomitants); les caractéristiques des omnipraticiens (réseau informel, formation); la culture professionnelle (travail en silo, mécanismes cliniques formalisés); le milieu institutionnel (multidisciplinarité, salariat); l’organisation des services (ressources; coordination formalisée) et l’environnement (politiques). Conclusion Le rôle clé des omnipraticiens et leur soutien à la prise en charge des TM ont été démontrés, spécifiquement pour les TMC. Pour une prise en charge optimale des soins primaires de santé mentale, des stratégies à composantes multiples, dont les soins partagés, devraient être davantage déployées.

Lignes directrices canadiennes sur l’utilisation sécuritaire et efficace des opioïdes pour la douleur chronique non cancéreuse

PubMed Central

Kahan, Meldon; Mailis-Gagnon, Angela; Wilson, Lynn; Srivastava, Anita

2011-01-01

Résumé Objectif Présenter aux médecins de famille un résumé clinique pratique des lignes directrices canadiennes sur l’utilisation sécuritaire et efficace des opioïdes pour la douleur chronique non cancéreuse, produites par le National Opioid Use Guideline Group. Qualité des données Pour produire les lignes directrices, les chercheurs ont effectué une synthèse critique de la littérature médicale sur l’efficacité et l’innocuité des opioïdes pour la douleur chronique non cancéreuse et ont rédigé une série de recommandations. Un panel de 49 cliniciens experts de toutes les régions du Canada ont passé en revue l’ébauche et ont atteint un consensus sur 24 recommandations. Message principal Il est recommandé de faire un dépistage du risque de dépendance avant de prescrire des opioïdes. On recommande des opioïdes faibles (codéine et tramadol) pour une douleur de légère à modérée qui n’a pas répondu aux traitements de première intention. On peut essayer l’oxycodone, l’hydromorphone et la morphine chez les patients qui n’ont pas eu de soulagement avec des opioïdes plus faibles. Une faible dose initiale et une lente hausse du titrage sont recommandées, ainsi qu’une étroite surveillance du patient qu’on a d’abord renseigné. Les médecins doivent surveiller l’apparition de complications comme l’apnée du sommeil. La dose optimale est celle qui améliore le fonctionnement ou atténue les cotes d’évaluation de la douleur d’au moins 30 %. Pour la grande majorité des patients, la dose optimale sera bien en deçà de l’équivalent de 200 mg de morphine par jour. On recommande le sevrage progressif pour les patients qui n’ont pas répondu à un essai d’opioïdes adéquat. Conclusion Les opioïdes jouent un rôle important dans la prise en charge de la douleur chronique non cancéreuse, mais il faut en prescrire avec prudence pour limiter les dommages potentiels. Les nouvelles lignes directrices canadiennes offrent des conseils dont les médecins avaient grand besoin pour les aider à en arriver à un juste équilibre entre le contrôle optimal de la douleur et la sécurité.

Effets de l'humidite sur la propagation du delaminage dans un composite carbone/epoxy sollicite en mode mixte I/II

NASA Astrophysics Data System (ADS)

LeBlanc, Luc R.

Les materiaux composites sont de plus en plus utilises dans des domaines tels que l'aerospatiale, les voitures a hautes performances et les equipements sportifs, pour en nommer quelques-uns. Des etudes ont demontre qu'une exposition a l'humidite nuit a la resistance des composites en favorisant l'initiation et la propagation du delaminage. De ces etudes, tres peu traitent de l'effet de l'humidite sur l'initiation du delaminage en mode mixte I/II et aucune ne traite des effets de l'humidite sur le taux de propagation du delaminage en mode mixte I/II dans un composite. La premiere partie de cette these consiste a determiner les effets de l'humidite sur la propagation du delaminage lors d'une sollicitation en mode mixte I/II. Des eprouvettes d'un composite unidirectionnel de carbone/epoxy (G40-800/5276-1) ont ete immergees dans un bain d'eau distillee a 70°C jusqu'a leur saturation. Des essais experimentaux quasi-statiques avec des chargements d'une gamme de mixites des modes I/II (0%, 25%, 50%, 75% et 100%) ont ete executes pour determiner les effets de l'humidite sur la resistance au delaminage du composite. Des essais de fatigue ont ete realises, avec la meme gamme de mixite des modes I/II, pour determiner 1'effet de 1'humidite sur l'initiation et sur le taux de propagation du delaminage. Les resultats des essais en chargement quasi-statique ont demontre que l'humidite reduit la resistance au delaminage d'un composite carbone/epoxy pour toute la gamme des mixites des modes I/II, sauf pour le mode I ou la resistance au delaminage augmente apres une exposition a l'humidite. Pour les chargements en fatigue, l'humidite a pour effet d'accelerer l'initiation du delaminage et d'augmenter le taux de propagation pour toutes les mixites des modes I/II. Les donnees experimentales recueillies ont ete utilisees pour determiner lesquels des criteres de delaminage en statique et des modeles de taux de propagation du delaminage en fatigue en mode mixte I/II proposes dans la litterature representent le mieux le delaminage du composite etudie. Une courbe de regression a ete utilisee pour determiner le meilleur ajustement entre les donnees experimentales et les criteres de delaminage en statique etudies. Une surface de regression a ete utilisee pour determiner le meilleur ajustement entre les donnees experimentales et les modeles de taux de propagation en fatigue etudies. D'apres les ajustements, le meilleur critere de delaminage en statique est le critere B-K et le meilleur modele de propagation en fatigue est le modele de Kenane-Benzeggagh. Afin de predire le delaminage lors de la conception de pieces complexes, des modeles numeriques peuvent etre utilises. La prediction de la longueur de delaminage lors des chargements en fatigue d'une piece est tres importante pour assurer qu'une fissure interlaminaire ne va pas croitre excessivement et causer la rupture de cette piece avant la fin de sa duree de vie de conception. Selon la tendance recente, ces modeles sont souvent bases sur l'approche de zone cohesive avec une formulation par elements finis. Au cours des travaux presentes dans cette these, le modele de progression du delaminage en fatigue de Landry & LaPlante (2012) a ete ameliore en y ajoutant le traitement des chargements en mode mixte I/II et en y modifiant l'algorithme du calcul de la force d'entrainement maximale du delaminage. Une calibration des parametres de zone cohesive a ete faite a partir des essais quasi-statiques experimentaux en mode I et II. Des resultats de simulations numeriques des essais quasi-statiques en mode mixte I/II, avec des eprouvettes seches et humides, ont ete compares avec les essais experimentaux. Des simulations numeriques en fatigue ont aussi ete faites et comparees avec les resultats experimentaux du taux de propagation du delaminage. Les resultats numeriques des essais quasi-statiques et de fatigue ont montre une bonne correlation avec les resultats experimentaux pour toute la gamme des mixites des modes I/II etudiee.

POURING FOOTING OF PIER #1. View is to the southwest, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

POURING FOOTING OF PIER #1. View is to the southwest, looking from Pier 2 in Trinity County toward Pier 1 in Humboldt County - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

Coronographie interferéntielle pour la mission spatuale DARWIN: expérience de validation en laboratoire

NASA Astrophysics Data System (ADS)

Ollivier, Marc; Mariotti, Jean-Marie; Brunaud, Jacqueline; Michel, Guy; Bouchareine, Patrick; Léger, Alain; Artzner, Guy; Malbet, Fabien; Puget, Pascal; Coudé du Foresto, Vincent; Mennesson, Bertrand

2018-04-01

This paper, "Coronographie interferéntielle pour la mission spatuale DARWIN: expérience de validation en laboratoire," was presented as part of International Conference on Space Optics—ICSO 1997, held in Toulouse, France.

Preventive effects of various types of footwear and cleaning methods on dermatophyte adhesion.

PubMed

Tanaka, Kumi; Katoh, Takuro; Irimajiri, Junya; Taniguchi, Hiroko; Yokozeki, Hiroo

2006-08-01

Tinea pedis is contagious and typically spreads from infected to non-infected persons. The purpose of this study was to evaluate the efficacy of footwear in preventing tinea pedis adhesion. Using the stamp culture method, we investigated the effectiveness of preventing dermatophyte passage by the wearing of stockings made of nylon, socks made of cotton and tabi (Japanese socks), as well as the effect of removing dermatophytes from these items by washing with soap, cold water and cold water after turning inside-out. For sandals, sneakers and boots, we also investigated the effect of dermatophyte removal by pouring cold water into the footwear, wiping with a wet towel, and pouring boiling water into the footwear. The wearing of socks or tabi was effective in preventing passage of dermatophytes. The stocking material proved to be too thin to prevent passage. On the inner side of socks (the side of the sole), all treatments were effective at removing dermatophytes, but on the outer side of socks (the side touching the surface of the sandals), the treatment of washing in cold water after turning inside-out resulted in significantly more dermatophytes as compared with the other treatments. Pouring cold water, wiping with a wet towel and pouring boiling water were all effective for removing dermatophytes from sandals and sneakers. However, for boots, the treatment of pouring cold water was less effective. To prevent the adhesion of dermatophytes to sandals, wearing socks or tabi was effective, and the treatments of washing socks in cold water after turning inside-out and of pouring cold water into the boots were less effective than the others.

Validation de modeles d'eclairement incident a la surface de l'eau en Arctique

NASA Astrophysics Data System (ADS)

Julien, Laliberte

Dans ce memoire, deux methodes d'estimation d'eclairement incident a la surface de l'Arctique sont evaluees. Une base de donnees in situ a ete constituee a partir de 16 campagnes oceanographiques en Arctique. Pour les dates ou l'eclairement est mesure, les estimations d'eclairement journalier incident a la surface obtenues a partir des satellites de la couleur de l'eau (Frouin et al. 2003) et a partir des satellites meteorologiques (Belanger et al. 2013) sont produites. De meme, un exercise de comparaison entre les estimations satellitaires est produit pour l'annee 2004 sur tout le territoire Arctique. La comparaison entre les donnees observees et les donnees estimees a partir des satellites meteorologiques donnent un biais de 6% et une quadratique moyenne 33%. La comparaison entre les observations et les satellites de la couleur de l'eau donnent un biais de 2% et 20%. Finalement, la difference moyenne entre les estimations des 2 methodes d'estimation satellitaires pour tout l'Arctique pour l'annee 2004 est de 0,29 Einstein/m2/jour avec un ecart-type de 6,78 Einstein/m2/jour. Les resultats montrent entre autres que la methode qui utilise les satellites de la couleur de l'eau est plus precise pour estimer l'eclairement sur une petite superficie puisqu'elle rend mieux les variations locales dans l'eclairement. La methode qui utilise les satellites meteorologique est plus precise pour estimer l'eclairement sur une grande superficie, puisqu'elle est moins restreinte dans les conditions qui permettent de fournir une estimation. Ainsi, la methode qui utilise les satellites meteorologiques montre qu'un eclairement annuel de l'Arctique de 38% n'est pas prise en compte par les satellites de la couleur de l'eau.

Low cracking concretes for the closure pours and overlays of the Dunlap Creek Bridge : final report.

DOT National Transportation Integrated Search

2017-10-01

Joints, wide cracks, and poor-quality concretes facilitate the intrusion of chlorides, causing corrosion in bridge decks and substructures. In this study, joints were replaced with closure pours (link slabs) consisting of low permeability fiber-reinf...

Chlorhexidine droplet splash from a skin preparation gallipot: effect of height of pouring.

PubMed

Evans, L; Cunningham, M; Tilakaratna, P

2013-12-01

Chlorhexidine contamination of equipment used in central neuraxial anaesthesia has been implicated in causing adhesive arachnoiditis. We measured the extent of chlorhexidine splash during pouring into a gallipot (antiseptic skin preparation container) from heights of 5 cm, 10 cm, 15 cm and 20 cm. Twenty experiments were performed at each height. Measurements made up to a horizontal distance of 40 cm radius from the gallipot showed a median (IQR [range]) maximum spread of splash droplets ≥ 2 mm diameter of 26.2 (10.2-36.4 [0-40]) cm. The 40-cm radius measurement area was divided into 5-cm-wide zones to assess spread. At pouring heights of 15 cm and 20 cm, all zones were contaminated. These results demonstrate that pouring chlorhexidine into a gallipot generates significant splash, and we recommend that this should be avoided near equipment used for neuraxial anaesthesia. © 2013 The Association of Anaesthetists of Great Britain and Ireland.

Fabrication par injection flexible de pieces coniques pour des applications aerospatiales

NASA Astrophysics Data System (ADS)

Shebib Loiselle, Vincent

Les materiaux composites sont presents dans les tuyeres de moteurs spatiaux depuis les annees soixante. Aujourd'hui, l'avenement des tissus tridimensionnels apporte une solution innovatrice au probleme de delamination qui limitait les proprietes mecaniques de ces composites. L'utilisation de ces tissus necessite toutefois la conception de procedes de fabrication mieux adaptes. Une nouvelle methode de fabrication de pieces composites pour des applications aerospatiales a ete etudiee tout au long de ce travail. Celle-ci applique les principes de l'injection flexible (procede Polyflex) a la fabrication de pieces coniques de fortes epaisseurs. La piece de validation a fabriquer represente un modele reduit de piece de tuyere de moteur spatial. Elle est composee d'un renfort tridimensionnel en fibres de carbone et d'une resine phenolique. La reussite du projet est definie par plusieurs criteres sur la compaction et la formation de plis du renfort et sur la formation de porosites de la piece fabriquee. Un grand nombre d'etapes ont ete necessaires avant la fabrication de deux pieces de validation. Premierement, pour repondre au critere sur la compaction du renfort, la conception d'un outil de caracterisation a ete entreprise. L'etude de la compaction a ete effectuee afin d'obtenir les informations necessaires a la comprehension de la deformation d'un renfort 3D axisymetrique. Ensuite, le principe d'injection de la piece a ete defini pour ce nouveau procede. Pour en valider les concepts proposes, la permeabilite du renfort fibreux ainsi que la viscosite de la resine ont du etre caracterisees. A l'aide de ces donnees, une serie de simulations de l'ecoulement pendant l'injection de la piece ont ete realisees et une approximation du temps de remplissage calculee. Apres cette etape, la conception du moule de tuyere a ete entamee et appuyee par une simulation mecanique de la resistance aux conditions de fabrication. Egalement, plusieurs outillages necessaires pour la fabrication ont ete concus et installes au nouveau laboratoire CGD (composites grandes dimensions). En parallele, plusieurs etudes ont ete effectuees pour comprendre les phenomenes influencant la polymerisation de la resine.

Pouring rights contracts and childhood overweight: a critical theory perspective.

PubMed

Opalinski, Andra

2006-10-01

To examine school environments, and in particular, pouring rights contracts and how they relate to childhood overweight from a critical theory perspective. Pouring rights contracts provide a profit to powerful mega-corporations at the expense of children's health. There is a need to move beyond a solely individual approach to addressing childhood overweight and involve a social ecology approach. This would involve a push for social change, including removal of soda machines from schools, and changing marketing practices targeted at children. Nurses are poised in community situations to actively effect social changes to improve health outcomes of our nation's most vulnerable people, but nurses must get involved.

Cooperation or Competition? The American and French Foreign Policies in Africa (Cooperation ou concurrence? La politique africaine de la France et des Etats-Unis en Afrique sub-saharienne)

DTIC Science & Technology

2005-07-26

Villepin, appelle « des conflits ancestraux >>, c’est-di-dire des conflits pour le contr6le de ressources primaires , ou de territoire, ou pour des diff~rends...traduira par une plus grande attention portde aux sujets africains et aussi d la part du budget pour l’Afrique. Le facteur religieux Les missionnaires en...grands avions de transport ou celles des soldats 6tablissant des centres de soins m6dicaux avec les ONG. Comme Jean-Paul Ngoupand6 l’a exprim6: << On

Declinaisons militaires francaises des directives europeennes en matiere d’hemovigilance (French European Military Haemovigilance Guidelines)

DTIC Science & Technology

2010-11-03

du groupe sanguin A B O D et d’un dépistage du VIH et du VHC. Sauf exception (donneur originaire de zones endémiques pour le VHB, non contrôlé avant...réalisées les sérologies VIH , VHC et VHB pré-transfusionnelles. Pour fiabiliser cette procédure assez complexe, le CTSA assure la formation...sont contrôlés pour le VIH avant le départ en mission. Enfin, sur le terrain, les aphé- rèses sont pratiquées sur des donneurs réguliers. A

Development of performance-based guidelines for selection of bituminous-based hot-poured pavement crack sealant : an executive summary report.

DOT National Transportation Integrated Search

2009-01-01

This report summarizes research presented in separate technical reports, papers, and journal articles that collectively document the development of a systematic process to aid in the selection of appropriate bituminous hot-poured sealants for pavemen...

Evaluation of high-performance fiber-reinforced concrete for bridge deck connections, closure pours, and joints : final report.

DOT National Transportation Integrated Search

2017-01-01

Connections, closure pours, and joints in bridges are often sources of distress because of cracks and openings. Wide separation facilitates the penetration of harmful solutions that can lead to costly repairs. Cracks are caused by volumetric changes ...

Diagnostics optiques pour la mesure de fluides critiques en micro-gravité dans les instruments ALICE et DECLIC

NASA Astrophysics Data System (ADS)

Durieux, Alain; Babolat, Claude; Dureux, Pierre; Martin, Bernard

2018-04-01

This paper, "Diagnostics optiques pour la mesure de fluides critiques en micro-gravité dans les instruments ALICE et DECLIC," was presented as part of International Conference on Space Optics—ICSO 1997, held in Toulouse, France.

Développement d'un capteur optique de pression pour la mesure in-situ des moteurs cryogéniques

NASA Astrophysics Data System (ADS)

Girault, Marc; Graindorge, Philippe; Laloux, Bernard; Desforges, Francois-Xavier; Martin, Philippe; Lefevre, Herve; Rouhet, Jacky

2018-04-01

This paper, "Développement d'un capteur optique de pression pour la mesure in-situ des moteurs cryogéniques," was presented as part of International Conference on Space Optics—ICSO 1997, held in Toulouse, France.

Apparatus Review.

ERIC Educational Resources Information Center

Byrum, David L.

1982-01-01

Suggests uses for and possible adaptations of a set of semiflexible molecular models. Includes price and supplier information. Also suggests rubbing oil from human face/hands along the pouring lip of a beaker, allowing one to pour uniformly from the beaker spout and making the process as dripless as possible. (Author/JN)

Etude de la performance des radars hautes-frequences CODAR et WERA pour la mesure des courants marins en presence partielle de glace de mer

NASA Astrophysics Data System (ADS)

Kamli, Emna

Les radars hautes-frequences (RHF) mesurent les courants marins de surface avec une portee pouvant atteindre 200 kilometres et une resolution de l'ordre du kilometre. Cette etude a pour but de caracteriser la performance des RHF, en terme de couverture spatiale, pour la mesure des courants de surface en presence partielle de glace de mer. Pour ce faire, les mesures des courants de deux radars de type CODAR sur la rive sud de l'estuaire maritime du Saint-Laurent, et d'un radar de type WERA sur la rive nord, prises pendant l'hiver 2013, ont ete utilisees. Dans un premier temps, l'aire moyenne journaliere de la zone ou les courants sont mesures par chaque radar a ete comparee a l'energie des vagues de Bragg calculee a partir des donnees brutes d'acceleration fournies par une bouee mouillee dans la zone couverte par les radars. La couverture des CODARs est dependante de la densite d'energie de Bragg, alors que la couverture du WERA y est pratiquement insensible. Un modele de fetch appele GENER a ete force par la vitesse du vent predite par le modele GEM d'Environnement Canada pour estimer la hauteur significative ainsi que la periode modale des vagues. A partir de ces parametres, la densite d'energie des vagues de Bragg a ete evaluee pendant l'hiver a l'aide du spectre theorique de Bretschneider. Ces resultats permettent d'etablir la couverture normale de chaque radar en absence de glace de mer. La concentration de glace de mer, predite par le systeme canadien operationnel de prevision glace-ocean, a ete moyennee sur les differents fetchs du vent selon la direction moyenne journaliere des vagues predites par GENER. Dans un deuxieme temps, la relation entre le ratio des couvertures journalieres obtenues pendant l'hiver 2013 et des couvertures normales de chaque radar d'une part, et la concentration moyenne journaliere de glace de mer d'autre part, a ete etablie. Le ratio des couvertures decroit avec l'augmentation de la concentration de glace de mer pour les deux types de radars, mais pour une concentration de glace de 20% la couverture du WERA est reduite de 34% alors que pour les CODARs elle est reduite de 67%. Les relations empiriques etablies entre la couverture des RHF et les parametres environnementaux (vent et glace de mer) permettront de predire la couverture que pourraient fournir des RHF installes dans d'autres regions soumises a la presence saisonniere de glace de mer.

Instrumentation optique pour l'identification per-operatoire des tissus durant les chirurgies de la thyroide

NASA Astrophysics Data System (ADS)

De Montigny, Etienne

Cette these traite du developpement d'instrumentation pour l'imagerie medicale optique. Ces travaux sont centres sur une application particuliere ; faciliter l'identification des tissus durant les chirurgies de la thyroide et de la parathyroide. La thyroide est une glande situee dans le cou, attachee au larynx a la hauteur de la pomme d'Adam. Elle est entouree de plusieurs structures importantes : muscles, nerfs et glandes parathyroides. Ces dernieres controlent la calcemie et jouent donc un role essentiel dans le corps. Elles sont toutefois de petite taille et sont tres difficiles a distinguer du gras et des ganglions environnants. L'objectif principal de cette these est de developper une instrumentation basee sur la microscopie optique pour permettre l'identification des tissus : thyroide, parathyroide, gras et ganglions, durant les chirurgies. Les choix sont donc faits en fonction de cette application et du contexte specifique des mesures intra-operatoires sur des patients humains. Plusieurs modalites d'imagerie optique sont identifiees pour atteindre l'objectif : microscopie confocale en reflectance, tomographique par coherence optique, et mesure de l'autofluorescence des glandes parathyroides. Dans le but d'ameliorer leur compatibilite avec l'environnement clinique qui requiert stabilite dans le temps et resistance aux vibrations et aux conditions environnementales, ce projet se concentre sur les implementations miniaturisables et basees sur des fibres optiques. Pour implementer un systeme d'imagerie en fluorescence a balayage laser rapide, un systeme d'imagerie en fluorescence par encodage spectral est propose. Bien que l'utilisation de l'encodage spectral semble a priori incompatible avec le contraste en fluorescence, une implementation facile a realiser est proposee. Une seconde version du montage, compatible avec la clinique et facilitant le developpement d'un endoscope, est presentee. La preuve de principe de cette methode est faite a 1300nm, une longueur d'onde qui n'est pas appropriee pour la fluorescence intrinseque des parathyroides. Pour adresser cette lacune, une nouvelle source laser a balayage centree a 780nm a haute puissance (100mW) est montree. Ces developpements sont compatibles avec l'implementation de la microscopie confocale en reflectance identifiee pour l'identification des tissus durant les chirurgies de la thyroide. Cela permet de developper un montage combinant le contraste en reflectance et en fluorescence dans le meme instrument. La microscopie confocale en reflectance possede une tres grande resolution permettant l'examen au niveau cellulaire des tissus. Cette technique souffre toutefois d'un faible rapport signal sur bruit et d'un bruit de tavelure important, reduisant l'interpretabilite des images.

Evaluation de la qualite osseuse par les ondes guidees ultrasonores =

NASA Astrophysics Data System (ADS)

Abid, Alexandre

La caracterisation des proprietes mecaniques de l'os cortical est un domaine d'interet pour la recherche orthopedique. En effet, cette caracterisation peut apporter des informations primordiales pour determiner le risque de fracture, la presence de microfractures ou encore depister l'osteoporose. Les deux principales techniques actuelles de caracterisation de ces proprietes sont le Dual-energy X-ray Absorptiometry (DXA) et le Quantitative Computed Tomogaphy (QCT). Ces techniques ne sont pas optimales et presentent certaines limites, ainsi l'efficacite du DXA est questionnee dans le milieu orthopedique tandis que le QCT necessite des niveaux de radiations problematiques pour en faire un outil de depistage. Les ondes guidees ultrasonores sont utilisees depuis de nombreuses annees pour detecter les fissures, la geometrie et les proprietes mecaniques de cylindres, tuyaux et autres structures dans des milieux industriels. De plus, leur utilisation est plus abordable que celle du DXA et n'engendrent pas de radiation ce qui les rendent prometteuses pour detecter les proprietes mecaniques des os. Depuis moins de dix ans, de nombreux laboratoires de recherche tentent de transposer ces techniques au monde medical, en propageant les ondes guidees ultrasonores dans les os. Le travail presente ici a pour but de demontrer le potentiel des ondes guidees ultrasonores pour determiner l'evolution des proprietes mecaniques de l'os cortical. Il commence par une introduction generale sur les ondes guidees ultrasonores et une revue de la litterature des differentes techniques relatives a l'utilisation des ondes guidees ultrasonores sur les os. L'article redige lors de ma maitrise est ensuite presente. L'objectif de cet article est d'exciter et de detecter certains modes des ondes guides presentant une sensibilite a la deterioration des proprietes mecaniques de l'os cortical. Ce travail est realise en modelisant par elements finis la propagation de ces ondes dans deux modeles osseux cylindriques. Ces deux modeles sont composes d'une couche peripherique d'os cortical et remplis soit d'os trabeculaire soit de moelle osseuse. Ces deux modeles permettent d'obtenir deux geometries, chacune propice a la propagation circonferentielle ou longitudinale des ondes guidees. Les resultats, ou trois differents modes ont pu etre identifies, sont compares avec des donnees experimentales obtenues avec des fantomes osseux et theoriques. La sensibilite de chaque mode pour les differents parametres des proprietes mecaniques est alors etudiee ce qui permet de conclure sur le potentiel de chaque mode quant a la prediction de risque de fracture ou de presence de microfractures.

Effects of Pouring Temperature and Electromagnetic Stirring on Porosity and Mechanical Properties of A357 Aluminum Alloy Rheo-Diecasting

NASA Astrophysics Data System (ADS)

Guo, An; Zhao, Junwen; Xu, Chao; Li, Hu; Han, Jing; Zhang, Xu

2018-05-01

Semisolid slurry of A357 aluminum alloy was prepared using a temperature-controllable electromagnetic stirrer and rheo-diecast at different temperatures. The effects of pouring temperature and electromagnetic stirring (EMS) on the porosity in rheo-diecast samples, as well as the relation between porosity and mechanical properties, were investigated. The results show that pouring temperature and EMS had minor influences on rheo-diecast microstructure but marked influence on the porosity. With decreasing slurry pouring temperature, the porosity decreased first and then increased, whereas the maximum pore ratio (ratio of shape factor to diameter of the largest pore) increased first and then decreased. The maximum pore ratio determines the level of tensile strength and elongation, and higher mechanical properties can be obtained with smaller and rounder pores in samples. The mechanical properties of the rheo-diecast samples increased linearly with increasing maximum pore ratio. The maximum pore ratio was 1.43 µm-1, and the minimum porosity level was 0.37% under EMS condition for the rheo-diecast samples obtained at a pouring temperature of 608 °C. With this porosity condition, the maximum tensile strength and elongation were achieved at 274 MPa and 4.9%, respectively. It was also revealed that EMS improves mechanical properties by reduction in porosity and an increase in maximum pore ratio.

Élaboration d'un bronze Cu-8%Sn fritté sous pression et l'étude de son aptitude à l'absorption

NASA Astrophysics Data System (ADS)

Loucif, K.; Keraghel, F.; Alem, S.

2005-05-01

L'introduction des píeces miniatures dans le domaine de l'informatique et la microélectronique nécessite une grande précision et un environnement propre. D'autre part, la conservation d'énergie exige des pièces légères et une bonne longévité. Pour résoudre ces problèmes, des pièces autolubrifiées ont été proposées. En effet, plusieurs disciplines peuvent s'ingérer pour élaborer ces pièces: la métallurgie des poudres pour produire des pièces poreuses, la tribologie pour caractériser la pièce en fonctionnement et la mécanique des fluides pour évaluer le comportement échantillon -lubrifiant.
Dans ce présent travail, nous présentons l'évolution de la densité des échantillons élaborés en fonction de: la température d'élaboration, la pression de compactage, et le temps de maintien et l'évolution de l'absorption des lubrifiants par un alliage Cu-8% Sn fritté sous pression. Les lubrifiants choisis sont l'eau et une huile de machine à usage domestique et leur aptitude à l'autolubrification.

Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter. Preliminary settling and resuspension testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.; Fowley, M. D.; Miller, D. H.

2016-05-01

The full-scale, room-temperature Hanford Tank Waste Treatment and Immobilization Plant (WTP) High-Level Waste (HLW) melter riser test system was successfully operated with silicone oil and magnetite particles at a loading of 0.1 vol %. Design and construction of the system and instrumentation, and the selection and preparation of simulant materials, are briefly reviewed. Three experiments were completed. A prototypic pour rate was maintained, based on the volumetric flow rate. Settling and accumulation of magnetite particles were observed at the bottom of the riser and along the bottom of the throat after each experiment. The height of the accumulated layer atmore » the bottom of the riser, after the first pouring experiment, approximated the expected level given the solids loading of 0.1 vol %. More detailed observations of particle resuspension and settling were made during and after the third pouring experiment. The accumulated layer of particles at the bottom of the riser appeared to be unaffected after a pouring cycle of approximately 15 minutes at the prototypic flow rate. The accumulated layer of particles along the bottom of the throat was somewhat reduced after the same pouring cycle. Review of the time-lapse recording showed that some of the settling particles flow from the riser into the throat. This may result in a thicker than expected settled layer in the throat.« less

Croissance epitaxiale de GaAs sur substrats de Ge par epitaxie par faisceaux chimiques

NASA Astrophysics Data System (ADS)

Belanger, Simon

La situation energetique et les enjeux environnementaux auxquels la societe est confrontee entrainent un interet grandissant pour la production d'electricite a partir de l'energie solaire. Parmi les technologies actuellement disponibles, la filiere du photovoltaique a concentrateur solaire (CPV pour concentrator photovoltaics) possede un rendement superieur et mi potentiel interessant a condition que ses couts de production soient competitifs. La methode d'epitaxie par faisceaux chimiques (CBE pour chemical beam epitaxy) possede plusieurs caracteristiques qui la rendent interessante pour la production a grande echelle de cellules photovoltaiques a jonctions multiples a base de semi-conducteurs III-V. Ce type de cellule possede la meilleure efficacite atteinte a ce jour et est utilise sur les satellites et les systemes photovoltaiques a concentrateur solaire (CPV) les plus efficaces. Une des principales forces de la technique CBE se trouve dans son potentiel d'efficacite d'utilisation des materiaux source qui est superieur a celui de la technique d'epitaxie qui est couramment utilisee pour la production a grande echelle de ces cellules. Ce memoire de maitrise presente les travaux effectues dans le but d'evaluer le potentiel de la technique CBE pour realiser la croissance de couches de GaAs sur des substrats de Ge. Cette croissance constitue la premiere etape de fabrication de nombreux modeles de cellules solaires a haute performance decrites plus haut. La realisation de ce projet a necessite le developpement d'un procede de preparation de surface pour les substrats de germanium, la realisation de nombreuses sceances de croissance epitaxiale et la caracterisation des materiaux obtenus par microscopie optique, microscopie a force atomique (AFM), diffraction des rayons-X a haute resolution (HRXRD), microscopie electronique a transmission (TEM), photoluminescence a basse temperature (LTPL) et spectrometrie de masse des ions secondaires (SIMS). Les experiences ont permis de confirmer l'efficacite du procede de preparation de surface et d'identifier les conditions de croissance optimales. Les resultats de caracterisation indiquent que les materiaux obtenus presentent une tres faible rugosite de surface, une bonne qualite cristalline et un dopage residuel relativement important. De plus, l'interface GaAs/Ge possede une faible densite de defauts. Finalement, la diffusion d'arsenic dans le substrat de germanium est comparable aux valeurs trouvees dans la litterature pour la croissance a basse temperature avec les autres procedes d'epitaxie courants. Ces resultats confirment que la technique d'epitaxie par faisceaux chimiques (CBE) permet de produire des couches de GaAs sur Ge de qualite adequate pour la fabrication de cellules solaires a haute performance. L'apport a la communaute scientifique a ete maximise par le biais de la redaction d'un article soumis a la revue Journal of Crystal Growth et la presentation des travaux a la conference Photovoltaics Canada 2010 . Mots-cles : Epitaxie par jets chimiques, Chemical beam epitaxy, CBE, MOMBE, Germanium, GaAs, Ge

Evaluation of a Pour-Through Water Treatment Device for Use as Microbiological Purifier

EPA Science Inventory

The United States Environmental Protection Agency (EPA) Office of Research and Development has evaluated the performance of a Point-of-Use (POU) pour-through device designed for use in India, developing and emerging market (D&E) countries, and under emergency situations in the Un...

Indicators, Predictors, and Determinants of Conflict Escalation and De-escalation. A Review of the Psychological Literature

DTIC Science & Technology

2009-05-01

des outils habituels de la psychologie parce que ces gens ne sont pratiquement jamais disponibles pour les chercheurs. Pour compenser, des méthodes...Ballard, E. J. (1983). Canadian prime ministers: Complexity in political crises. Canadian Psychology/ Psychologie Canadienne, 24, 125-129. Beasley

40 CFR 464.02 - General definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... or final product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or... product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or other cast shapes... into a mold, except for ingots, pigs, or other cast shapes related to nonferrous (primary) metals...

40 CFR 464.02 - General definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... or final product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or... product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or other cast shapes... into a mold, except for ingots, pigs, or other cast shapes related to nonferrous (primary) metals...

Mesures experimentales de l'impact des revetements hydrophobeset superhydrophobes sur la trainee et la portance d'un profil aerodynamique propre et glace

NASA Astrophysics Data System (ADS)

Villeneuve, Eric

Ce projet, realise a la demande du Laboratoire International des Materiaux Antigivre, a pour but de mesurer et definir experimentalement l'impact de revetements hydrophobes sur les coefficients de trainee et de portance d'un profil NACA 0012. Pour ce faire, la balance aerodynamique du LIMA devait tout d'abord etre amelioree afin d'offrir une sensibilite suffisante pour realiser le projet. Plusieurs ameliorations ont ete faites, comme le changement des cellules de charge, la diminution du nombre de cellules de charge, le changement du cadre de la balance, etc. Une fois ces ameliorations terminees, la reproductibilite, l'exactitude et la sensibilite ont ete valides afin de s'assurer de la fiabilite des resultats offerts par la balance. Pour les angles d'attaque etudies avec les revetements, soient -6° et 0°, la balance a une reproductibilite de +/-2,06% a 360 000 de nombre de Reynolds. Pour valider la sensibilite, des essais a -6° et 0° d'angle d'attaque et des nombres de Reynolds de 360 000 et 500 000 ont ete faits avec des papiers sables. Les resultats de ces essais ont permis de, tracer des courbes de tendances du coefficient de trainee du NACA 0012 en fonction de la rugosite de surface et d'etablir la valeur de la sensibilite de la balance a +/-8 mu m. Cinq revetements populaires ont ete choisis pour l'experimentation, soient le Wearlon, le Staclean, le Hirec, le Phasebreak ainsi que le Nusil. Les revetements sont soumis aux memes conditions experimentales que les papiers sables, et une rugosite equivalente est trouvee par extrapolation des resultats. Cependant, les rugosites equivalentes de surfaces different entre -6° et 0°. Les essais avec le Staclean et le Hirec donnent des coefficients de trainee equivalent a ceux avec l'aluminium, alors que le Wearlon, le Nusil et le Phasebreak donnent une augmentation du coefficient de trainee de 13%, 17% et 25% respectivement par rapport a l'aluminium. Pour les coefficients de portance, la balance ne detecte pas l'effet des revetements, ni des papiers sables, sur la force de portance ce qui signifie qu'il entre dans l'insensibilite de la balance. La derniere etape experimentale consistait a mesurer l'impact des revetements sur la formation de la glace ainsi que sur l'evolution des coefficients de trainee et de portance du NACA 0012 en fonction de l'accumulation de glace sur celui-ci. Le Wearlon a ete choisi comme revetement en raison de sa grande popularite. Des essais a -5°C et -20°C ont ete faits et les resultats ont montres que le Wearlon n'apporte pas d'effet benefique au NACA 0012 en conditions d'accumulations de glace. L'augmentation du coefficient de trainee du profil muni du Wearlon debutait plus rapidement que sur l'aluminium et de l'eau gelait legerement plus loin vers l'arriere du profil pendant les essais, ce qui n'est pas souhaitable. Le coefficient de trainee est superieur d'environ 13% pour le Wearlon par rapport a l'aluminium pendant toute l'accumulation de glace, ce qui correspond au meme ecart lorsque la glace n'est pas en cause. Pour le coefficient de portance, les resultats ne peuvent etre utilises pour une raison qui doit etre investiguee.

Developpement d'un montage simulant l'erosion par la pluie pour l'evaluation des revetements glaciophobes dans le domaine aerospatial

NASA Astrophysics Data System (ADS)

Tremblay, Sarah-Eve

Ce memoire presente le developpement d’un montage simulant l’erosion par la pluie afin d’effectuer l’evaluation de differents revetements glaciophobes dans le domaine aerospatial. Bien que plusieurs revetements presentent une bonne efficacite a reduire l’adherence et/ou l’accumulation de glace, ils ne repondent pas necessairement aux normes de resistance a l’erosion simulee par les gouttes de pluie les frappant a grande vitesse. Il n’existe qu’une installation en Amerique du Nord offrant un service d’essai qui evalue la resistance a l’erosion par la pluie suivant les normes aerospatiales. Etant l’unique institution pouvant faire la certification de peintures utilisees sur les avions en ce qui a trait a l’erosion par la pluie, ce service est donc difficile d’acces et couteux. Le laboratoire international des materiaux antigivre (LIMA) a developpe un essai plus rapide et moins couteux, facilitant ainsi le developpement de revetements glaciophobes devant resister a l’erosion par la pluie. Dans cette etude, le developpement du montage d’erosion par la pluie effectue au laboratoire des materiaux antigivre (LIMA) est presente. En particulier, des essais sur quatre (4) revetements dont la resistance a l’erosion est connue, et sur trois revetements industriels, ont ete effectues afin d’ajuster les differents parametres du montage comme la pression et la temperature de l’eau ainsi que la robustesse du montage. Ensuite, des essais de sensibilite et de reproductibilite des resultats ont egalement ete effectues pour fin de validation du montage et du protocole experimental. Pour ce faire, le montage de type jet d’eau developpe consiste principalement en une pompe a haute pression qui projette un jet d’eau continu passant par les orifices d’un disque tournant. Cette operation permet de generer une goutte de pluie simulee qui est projetee sur un echantillon de revetement statique. L’essai est base sur la norme standard ASTM (Liquid Impingement Erosion Testing, G73-82). La resistance a l’erosion du materiau est determinee a l’aide du nombre d’impacts subi par l’echantillon obtenu avant la production de dommages visibles. Donc, pour determiner le niveau d’erosion, quatre sites d’impacts doivent etre erodes sur cinq sur le meme rang pour le meme nombre d’impact. L’analyse des quatre revetements de resistance a l’erosion connus a ete completee par l’examen microscopique de chaque site d’impact et d’une photo. Le choix des quatre revetements de resistance a l’erosion connue, allant du plus resistant au moins resistant, a permis de verifier que le montage etait assez sensible pour evaluer les revetements souvent utilises dans le domaine aerospatial. De plus, l’evaluation des trois revetements industriels a permis, pour sa part, de confirmer les resultats obtenus precedemment. Finalement, pour evaluer la sensibilite et la reproductibilite des resultats, de deux a six repetitions pour chaque revetement a ete effectuees donnant des taux d’erosion allant de 100 a 100 000 impacts. L’intervalle des ecarts-types varie de ± 0% a ± 47% pour une moyenne de ± 17%. Le critere d’echec a ete determine a l’aide du nombre d’impacts avant l’apparition de dommage visible ainsi que de la repetabilite des resultats.

Using polymerization, glass structure, and quasicrystalline theory to produce high level radioactive borosilicate glass remotely: a 20+ year legacy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jantzen, Carol M.

Vitrification is currently the most widely used technology for the treatment of high level radioactive wastes (HLW) throughout the world. Most of the nations that have generated HLW are immobilizing in borosilicate glass. One of the primary reasons that glass has become the most widely used immobilization media is the relative simplicity of the vitrification process, e.g. melt a highly variable waste with some glass forming additives such as SiO 2 and B 2O 3 in the form of a premelted frit and pour the molten mixture into a stainless steel canister. Seal the canister before moisture can enter themore » canister (10’ tall by 2’ in diameter) so the canister does not corrode from the inside out. Glass has also become widely used for HLW is that due to the fact that the short range order (SRO) and medium range order (MRO) found in the structure of glass atomistically bonds the radionuclides and hazardous species in the waste. The SRO and MRO have also been found to govern the melt properties such as viscosity and resistivity of the melt and the crystallization potential and solubility of certain species. Furthermore, the molecular structure of the glass also controls the glass durability, i.e. the contaminant/radionuclide release, by establishing the distribution of ion exchange sites, hydrolysis sites, and the access of water to those sites. The molecular structure is flexible and hence accounts for the flexibility of glass formulations to HLW waste variability. Nuclear waste glasses melt between 1050-1150°C which minimizes the volatility of radioactive components such as 99Tc, 137Cs, and 129I. Nuclear waste glasses have good long term stability including irradiation resistance. Process control models were developed based on the molecular structure of glass, polymerization theory of glass, and quasicrystalline theory of glass crystallization. These models create a glass which is durable, pourable, and processable with 95% accuracy without knowing from batch to batch what the composition of the waste coming out of the storage tanks will be. These models have operated the Savannah River Site Defense Waste Processing Facility (SRS DWPF), which is the world’s largest HLW Joule heated ceramic melter, since 1996. This unique “feed forward” process control, which qualifies the durability, pourability, and processability of the waste plus glass additive mixture before it enters the melter, has enabled ~8000 tons of HLW glass and 4242 canisters to be produced since 1996 with only one melter replacement.« less

Using polymerization, glass structure, and quasicrystalline theory to produce high level radioactive borosilicate glass remotely: a 20+ year legacy

DOE PAGES

Jantzen, Carol M.

2017-03-27

Vitrification is currently the most widely used technology for the treatment of high level radioactive wastes (HLW) throughout the world. Most of the nations that have generated HLW are immobilizing in borosilicate glass. One of the primary reasons that glass has become the most widely used immobilization media is the relative simplicity of the vitrification process, e.g. melt a highly variable waste with some glass forming additives such as SiO 2 and B 2O 3 in the form of a premelted frit and pour the molten mixture into a stainless steel canister. Seal the canister before moisture can enter themore » canister (10’ tall by 2’ in diameter) so the canister does not corrode from the inside out. Glass has also become widely used for HLW is that due to the fact that the short range order (SRO) and medium range order (MRO) found in the structure of glass atomistically bonds the radionuclides and hazardous species in the waste. The SRO and MRO have also been found to govern the melt properties such as viscosity and resistivity of the melt and the crystallization potential and solubility of certain species. Furthermore, the molecular structure of the glass also controls the glass durability, i.e. the contaminant/radionuclide release, by establishing the distribution of ion exchange sites, hydrolysis sites, and the access of water to those sites. The molecular structure is flexible and hence accounts for the flexibility of glass formulations to HLW waste variability. Nuclear waste glasses melt between 1050-1150°C which minimizes the volatility of radioactive components such as 99Tc, 137Cs, and 129I. Nuclear waste glasses have good long term stability including irradiation resistance. Process control models were developed based on the molecular structure of glass, polymerization theory of glass, and quasicrystalline theory of glass crystallization. These models create a glass which is durable, pourable, and processable with 95% accuracy without knowing from batch to batch what the composition of the waste coming out of the storage tanks will be. These models have operated the Savannah River Site Defense Waste Processing Facility (SRS DWPF), which is the world’s largest HLW Joule heated ceramic melter, since 1996. This unique “feed forward” process control, which qualifies the durability, pourability, and processability of the waste plus glass additive mixture before it enters the melter, has enabled ~8000 tons of HLW glass and 4242 canisters to be produced since 1996 with only one melter replacement.« less

Effets de la formation sur la violence conjugale

PubMed Central

Zaher, Eman; Keogh, Kelly; Ratnapalan, Savithiri

2014-01-01

Résumé Objectif Décrire et évaluer l’efficacité de la formation concernant la violence conjugale pour améliorer les connaissances et permettre la reconnaissance et la prise en charge par les médecins des femmes victimes de violence. Sources des données On a fait une recension dans la base de données des révisions systématiques de Cochrane, MEDLINE, PubMed, PsycINFO, ERIC et EMBASE pour trouver des articles publiés entre le 1e janvier 2000 et le 1e novembre 2012. Des recherches manuelles ont complété cette recension pour cerner des articles pertinents à l’aide d’une stratégie de recherche combinant des textes, mots et expressions MeSH. Sélection des études On a choisi des études randomisées contrôlées qui portaient sur des interventions éducatives à l’intention des médecins et fournissaient des données sur les effets des interventions. Synthèse On a inclus 9 études randomisées contrôlées qui décrivaient différentes approches pédagogiques et diverses mesures des résultats. Trois études examinaient les effets d’interventions éducatives pour des médecins en formation postdoctorale et ont constaté une augmentation des connaissances, mais il n’y a eu aucun changement dans le comportement en ce qui a trait à l’identification des victimes de violence conjugale. Six études portaient sur des interventions éducatives pour des médecins en pratique active. Trois d’entre elles utilisaient une approche à multiples facettes pour les médecins, qui combinait une formation ainsi que des interventions de soutien de la part du système pour changer les comportements des médecins, comme une sensibilisation générale accrue à la violence conjugale au moyen de brochures et d’affiches, des aide-mémoire pour rappeler aux médecins comment identifier les victimes, des moyens pour faciliter l’accès des médecins à des services de soutien pour les victimes, la réalisation d’audits et la fourniture de rétroaction. Les interventions éducatives à multiples facettes prenaient la forme d’ateliers interactifs, d’apprentissage sur le web et de formation expérientielle. Une autre étude utilisait des discussions de groupes témoins et de la formation et a permis de constater une amélioration dans le signalement de la violence conjugale par les médecins. Les 2 autres études ont relevé une meilleure perception par les médecins en pratique de leur confiance en eux à l’aide d’apprentissage par problèmes en ligne. Conclusion Il a été difficile de déterminer quelle stratégie pédagogique était la plus efficace étant donné que les interventions éducatives et les mesures des résultats variaient entre les études choisies. De brèves interventions pour les médecins en formation postdoctorale amélioraient les connaissances mais ne semblaient pas influencer les comportements. La formation en ligne sous forme d’apprentissage par problèmes améliorait les perceptions des médecins en pratique, leurs connaissances et leurs habiletés quant à la prise en charge de la violence conjugale. La formation des médecins combinée à des interventions de soutien de la part du système semblait bénéfique aux victimes de violence conjugale et augmentait le nombre de demandes de consultations auprès des ressources de soutien à leur intention.

Formulation, caracterisation, modelisation et prevision du comportement thermomecanique des pieces plastiques et composites de fibres de bois : Application aux engrenages =

NASA Astrophysics Data System (ADS)

Mijiyawa, Faycal

Cette etude permet d'adapter des materiaux composites thermoplastiques a fibres de bois aux engrenages, de fabriquer de nouvelles generations d'engrenages et de predire le comportement thermique de ces engrenages. Apres une large revue de la litterature sur les materiaux thermoplastiques (polyethylene et polypropylene) renforces par les fibres de bois (bouleau et tremble), sur la formulation et l'etude du comportement thermomecanique des engrenages en plastique-composite; une relation a ete etablie avec notre presente these de doctorat. En effet, beaucoup d'etudes sur la formulation et la caracterisation des materiaux composites a fibres de bois ont ete deja realisees, mais aucune ne s'est interessee a la fabrication des engrenages. Les differentes techniques de formulation tirees de la litterature ont facilite l'obtention d'un materiau composite ayant presque les memes proprietes que les materiaux plastiques (nylon, acetal...) utilises dans la conception des engrenages. La formulation des materiaux thermoplastiques renforces par les fibres de bois a ete effectuee au Centre de recherche en materiaux lignocellulosiques (CRML) de l'Universite du Quebec a Trois-Rivieres (UQTR), en collaboration avec le departement de Genie Mecanique, en melangeant les composites avec deux rouleaux sur une machine de type Thermotron-C.W. Brabender (modele T-303, Allemand) ; puis des pieces ont ete fabriquees par thermocompression. Les thermoplastiques utilises dans le cadre de cette these sont le polypropylene (PP) et le polyethylene haute densite (HDPE), avec comme renfort des fibres de bouleau et de tremble. A cause de l'incompatibilite entre la fibre de bois et le thermoplastique, un traitement chimique a l'aide d'un agent de couplage a ete realise pour augmenter les proprietes mecaniques des materiaux composites. Pour les composites polypropylene/bois : (1) Les modules elastiques et les contraintes a la rupture en traction des composites PP/bouleau et PP/tremble evoluent lineairement en fonction du taux de fibres, avec ou sans agent de couplage (Maleate de polypropylene MAPP). De plus, l'adherence entre les fibres de bois et le plastique est amelioree en utilisant seulement 3 % MAPP, entrainant donc une augmentation de la contrainte maximale bien qu'aucun effet significatif ne soit observe sur le module d'elasticite. (2) Les resultats obtenus montrent que, en general, les proprietes en traction des composites polypropylene/bouleau, polypropylene/tremble et polypropylene/bouleau/ tremble sont tres semblables. Les composites plastique-bois (WPCs), en particulier ceux contenant 30 % et 40 % de fibres, ont des modules elastiques plus eleves que certains plastiques utilises dans l'application des engrenages (ex. Nylon). Pour les composites polyethylene/bois, avec 3%Maleate de polyethylene (MAPE): (1) Tests de traction : le module elastique passe de 1.34 GPa a 4.19 GPa pour le composite HDPE/bouleau, alors qu'il passe de 1.34 GPa a 3.86 GPa pour le composite HDPE/tremble. La contrainte maximale passe de 22 MPa a 42.65 MPa pour le composite HDPE/bouleau, alors qu'elle passe de 22 MPa a 43.48 MPa pour le composite HDPE/tremble. (2) Tests de flexion : le module elastique passe de 1.04 GPa a 3.47 GPa pour le composite HDPE/bouleau et a 3.64 GPa pour le composite HDPE/tremble. La contrainte maximale passe de 23.90 MPa a 66.70 MPa pour le composite HDPE/bouleau, alors qu'elle passe a 59.51 MPa pour le composite HDPE/tremble. (3) Le coefficient de Poisson determine par impulsion acoustique est autour de 0.35 pour tous les composites HDPE/bois. (4) Le test de degradation thermique TGA nous revele que les materiaux composites presentent une stabilite thermique intermediaire entre les fibres de bois et la matrice HDPE. (5) Le test de mouillabilite (angle de contact) revele que l'ajout de fibres de bois ne diminue pas de facon significative les angles de contact avec de l'eau parce que les fibres de bois (bouleau ou tremble) semblent etre enveloppees par la matrice sur la surface des composites, comme le montrent des images prises au microscope electronique a balayage MEB. (6) Le modele de Lavengoof-Goettler predit mieux le module elastique du composite thermoplastique/bois. (7) Le HDPE renforce par 40 % de bouleau est mieux adapte pour la fabrication des engrenages, car le retrait est moins important lors du refroidissement au moulage. La simulation numerique semble mieux predire la temperature d'equilibre a la vitesse de 500 tr/min; alors qu'a 1000 tr/min, on remarque une divergence du modele. (Abstract shortened by ProQuest.). None None None None None None None None

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zamecnik, J. R.; Edwards, T. B.

The conversions of nitrite to nitrate, the destruction of glycolate, and the conversion of glycolate to formate and oxalate were modeled for the Nitric-Glycolic flowsheet using data from Chemical Process Cell (CPC) simulant runs conducted by SRNL from 2011 to 2015. The goal of this work was to develop empirical correlations for these variables versus measureable variables from the chemical process so that these quantities could be predicted a-priori from the sludge composition and measurable processing variables. The need for these predictions arises from the need to predict the REDuction/OXidation (REDOX) state of the glass from the Defense Waste Processingmore » Facility (DWPF) melter. This report summarizes the initial work on these correlations based on the aforementioned data. Further refinement of the models as additional data is collected is recommended.« less

Miscibility Evaluation Of The Next Generation Solvent With Polymers Currently Used At DWPF, MCU, And Saltstone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F. F.

The Office of Waste Processing, within the Office of Technology Innovation and Development, funded the development of an enhanced Caustic-Side Solvent Extraction (CSSX) solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. This effort lead to the development of the Next Generation Solvent (NGS) with Tris (3,7-dimethyl octyl) guanidine (TiDG). The first deployment target for the NGS solvent is within the Modular CSSX Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the new chemical components are compatible with the installed equipment. In the instance of a newmore » organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the affected facility. This report provides the calculated data from exposing these polymers to the Next Generation Solvent. An assessment of the dimensional stability of polymers known to be used or present in the MCU, Defense Waste Processing Facility (DWPF), and Saltstone facilities that will be exposed to the NGS showed that TiDG could selectively affect the elastomers and some thermoplastics to varying extents, but the typical use of these polymers in a confined geometry will likely prevent the NGS from impacting component performance. The polymers identified as of primary concern include Grafoil® (flexible graphite), Tefzel®, Isolast®, ethylene-propylene-diene monomer (EPDM) rubber, nitrile-butadiene rubber (NBR), styrene-butadiene rubber (SBR), ultra high molecular weight polyethylene (UHMWPE), and fluorocarbon rubber (FKM). Certain polymers like NBR and EPDM were found to interact mildly with NGS but their calculated swelling and the confined geometry will impede interaction with NGS. In addition, it was found that Vellumoid (cellulose fibers-reinforced glycerin and protein) may leach protein and Polyvinyl Chloride (PVC) may leach plasticizer (such as Bis-Ethylhexyl-Phthalates) into the NGS solvent. Either case will not impact decontamination or immobilization operations at Savannah River Site (SRS). Some applications have zero tolerance for dimensional changes such as the operation of valves while other applications a finite dimensional change improves the function of the application such as seals and gaskets. Additional considerations are required before using the conclusions from this work to judge outcomes in field applications. Decane, a component of Isopar L that is most likely to interact with the polymers, mildly interacted with the elastomers and the propylene based polymers but their degree of swelling is at most 10% and the confined geometry that they are typically placed in indicate this is not significant. In addition, it was found that Vellumoid may leach protein into the NGS solvent. Since Vellumoid is used at the mixer in Saltstone where it sees minimum quantities of solvent, this leaching has no effect on the extraction process at MCU or the immobilization process at saltstone. No significant interaction is expected between MaxCalix and the polymers and elastomers used at MCU, DWPF, and Saltstone. Overall, minimal and insignificant interactions are expected on extraction and immobilization operations when MCU switches from CSSX to NGS solvent. It is expected that contacting NGS will not accelerate the aging rate of polymers and elastomers under radiation and heat. This is due to the minimal interaction between NGS and the polymers and the confined geometries for these polymers. SRNL recommends the use of the HSP method (for screening) and some testing to evaluate the impact of other organic such as alcohols, glycolate, and their byproducts on the polymers used throughout the site.« less

THE IMPACT OF THE MCU LIFE EXTENSION SOLVENT ON DWPF GLASS FORMULATION EFFORTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D; Edwards, T

2011-03-24

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NG-CSSX), a new strip acid, and modified monosodium titanate (mMST) will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing with the next generation solvent and mMST is required to determine the impact of these changes in 512-S operations as well as Chemical Process Cell (CPC), Defense Waste Processing Facility (DWPF) glass formulation activities, and melter operations at DWPF. To support programmatic objectives,more » the downstream impacts of the boric acid strip effluent (SE) to the glass formulation activities and melter operations are considered in this study. More specifically, the impacts of boric acid additions to the projected SB7b operating windows, potential impacts to frit production temperatures, and the potential impact of boron volatility are evaluated. Although various boric acid molarities have been reported and discussed, the baseline flowsheet used to support this assessment was 0.01M boric acid. The results of the paper study assessment indicate that Frit 418 and Frit 418-7D are robust to the implementation of the 0.01M boric acid SE into the SB7b flowsheet (sludge-only or ARP-added). More specifically, the projected operating windows for the nominal SB7b projections remain essentially constant (i.e., 25-43 or 25-44% waste loading (WL)) regardless of the flowsheet options (sludge-only, ARP added, and/or the presence of the new SE). These results indicate that even if SE is not transferred to the Sludge Receipt and Adjustment Tank (SRAT), there would be no need to add boric acid (from a trim tank) to compositionally compensate for the absence of the boric acid SE in either a sludge-only or ARP-added SB7b flowsheet. With respect to boron volatility, the Measurement Acceptability Region (MAR) assessments also suggest that Slurry Mix Evaporator (SME) acceptability decisions would not be different assuming either 100% of the B{sub 2}O{sub 3} from the SE were retained or volatilized. More specifically, the 0.84 wt% B{sub 2}O{sub 3} in the SE is so minor that its presence in the SME analysis does not influence SME acceptability decisions. In fact, using the 100% retention and 100% volatilization composition projections, only minor differences in the predicted properties of the glass product occur with all of the glasses being acceptable over a WL interval of 32-42%. Based on the 0.01M boric acid flowsheet, there is very little difference between Frit 418 and Frit 418-7D (a frit that was compositionally altered to account for the 0.84 wt% B{sub 2}O{sub 3} in the SE) with respect to melt temperature. In fact, when one evaluates the composition of Frit 418-7D, it lies within the current Frit 418 vendor specifications and therefore could have been produced by the vendor targeting the nominal composition of Frit 418.« less

40 CFR 464.25 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Copper Casting... Maximum for monthly average kg/1000 kkg (pounds per million pounds) of metal poured Copper (T) 0.0307 0... any 1 day Maximum for monthly average kg/1,000 kkg (pounds per million pounds) of metal poured Copper...

Topical (pour-on) ivermectin in the treatment of canine scabies.

PubMed Central

Paradis, M; de Jaham, C; Pagé, N

1997-01-01

The efficacy of a pour-on formulation of ivermectin at 500 micrograms/kg body weight applied on the dorsum on days 1 and 15 was evaluated in 90 dogs from a shelter, naturally infested with Sarcoptes scabiei. This very practical form of treatment was successful in eradicating scabies from this shelter. PMID:9187806

STEEL BEAMS FOR FIRST FLOOR BEING READIED FOR CONCRETE POUR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

STEEL BEAMS FOR FIRST FLOOR BEING READIED FOR CONCRETE POUR UNDER WEATHER SHELTER DURING COLD WINTER. NOTE ABUNDANCE OF BEAMS; THE FLOOR WILL SUPPORT HEAVY LOADS. INL NEGATIVE NO. 1175. Unknown Photographer, 12/20/1950 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Réseaux holographiques à 6000 t/mm pour l'experience fuse de spectroscopie à haute résolution dans l'ultraviolet lolntain

NASA Astrophysics Data System (ADS)

Grange, Robert; Dauer, Véronique; Saisse, Michel; Flamand, Jean; Bonnemason, Francis

2018-04-01

This paper, "Réseaux holographiques à 6000 t/mm pour l'experience fuse de spectroscopie à haute résolution dans l'ultraviolet lolntain," was presented as part of International Conference on Space Optics—ICSO 1997, held in Toulouse, France.

40 CFR 464.02 - General definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... intermediate or final product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or... product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or other cast shapes... into a mold, except for ingots, pigs, or other cast shapes related to nonferrous (primary) metals...

40 CFR 464.02 - General definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... intermediate or final product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or... product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or other cast shapes... into a mold, except for ingots, pigs, or other cast shapes related to nonferrous (primary) metals...

40 CFR 464.02 - General definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... intermediate or final product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or... product by pouring or forcing the molten metal into a mold, except for ingots, pigs, or other cast shapes... into a mold, except for ingots, pigs, or other cast shapes related to nonferrous (primary) metals...

Le contrôle des infections au cabinet du pédiatre

PubMed Central

2008-01-01

RÉSUMÉ La transmission des infections au cabinet du pédiatre est de plus en plus préoccupante. Le présent document expose les voies de transmission des infections et les principes sous-jacents aux mesures actuelles pour contrôler les infections. Pour prévenir les infections, il faut bien concevoir le cabinet et adopter des politiques administratives et de triage convenables, de même que des pratiques de base pour les soins de tous les patients (p. ex., hygiène des mains, port de gants, de masques, de lunettes de protection et d’une blouse d’hôpital pour des interventions précises; nettoyage, désinfection et stérilisation convenables des surfaces et du matériel, y compris les jouets, et techniques d’asepsie en cas d’interventions effractives) et des précautions additionnelles en cas d’infections précises. Le personnel doit avoir reçu les vaccins pertinents, et les personnes infectées doivent respecter les politiques de restriction au travail.

CO2 volume fluxes outgassing from champagne glasses: the impact of champagne ageing.

PubMed

Liger-Belair, Gérard; Villaume, Sandra; Cilindre, Clara; Jeandet, Philippe

2010-02-15

It was demonstrated that CO(2) volume fluxes outgassing from a flute poured with a young champagne (elaborated in 2007) are much higher than those outgassing from the same flute poured with an older champagne (elaborated in the early 1990s). The difference in dissolved-CO(2) concentrations between the two types of champagne samples was found to be a crucial parameter responsible for differences in CO(2) volume fluxes outgassing from one champagne to another. Nevertheless, it was shown that, for a given identical dissolved-CO(2) concentration in both champagne types, the CO(2) volume flux outgassing from the flute poured with the old champagne is, in average, significantly lower than that outgassing from the flute poured with the young one. Therefore, CO(2) seems to "escape" more easily from the young champagne than from the older one. The diffusion coefficient of CO(2) in both champagne types was pointed as a key parameter to thoroughly determine in the future, in order to unravel our experimental observation. Copyright 2009 Elsevier B.V. All rights reserved.

Near-perfect compliance with SCIP Inf-9 had no effect on catheter utilization or urinary tract infections at an academic medical center.

PubMed

Kaplan, Jennifer A; Carter, Jonathan T

2018-01-01

The Joint Commission's SCIP Inf-9 mandated early removal of indwelling urinary catheters (IUCs), but the impact of compliance on catheter-associated urinary tract infection (CAUTI) and postoperative urinary retention (POUR) are unknown. Retrospective pre- and post-intervention study at a single tertiary academic medical center of all patients undergoing general surgery procedures with an IUC placed at the time of surgery who were admitted for at least two days before and after a Best Practice Advisory was put in place to improve compliance with SCIP Inf-9. A total of 1036 patients were included (468 pre-intervention; 568 post-intervention). POUR occurred in 13% of patients and CAUTI in 0.8%. There was no change in POUR, CAUTI, or catheter utilization after the Best Practice Advisory was initiated. Both POUR and CAUTI predicted longer lengths of stay. Near-perfect SCIP Inf-9 compliance had no effect on the CAUTI rate at our institution. Copyright © 2017 Elsevier Inc. All rights reserved.

Etude de l'affaiblissement du comportement mecanique du pergelisol du au rechauffement climatique

NASA Astrophysics Data System (ADS)

Buteau, Sylvie

Le rechauffement climatique predit pour les prochaines decennies, aura des impacts majeurs sur le pergelisol qui sont tres peu documentes pour l'instant. La presente etude a pour but d'evaluer ces impacts sur les proprietes mecaniques du pergelisol et sa stabilite a long terme. Une nouvelle technique d'essai de penetration au cone a taux de deformation controle, a ete developpee pour caracteriser en place le pergelisol. Ces essais geotechniques et la mesure de differentes proprietes physiques ont ete effectues sur une butte de pergelisol au cours du printemps 2000. Le developpement et l'utilisation d'un modele geothermique 1D tenant compte de la thermodependance du comportement mecanique ont permis d'evaluer que les etendues de pergelisol chaud deviendraient instables a la suite d'un rechauffement de l'ordre de 5°C sur cent ans. En effet, la resistance mecanique du pergelisol diminuera alors rapidement jusqu'a 11,6 MPa, ce qui correspond a une perte relative de 98% de la resistance par rapport a un scenario sans rechauffement.

Wax inhibitor based on ethylene vinyl acetate with methyl methacrylate and diethanolamine for crude oil pipeline

NASA Astrophysics Data System (ADS)

Anisuzzaman, S. M.; Abang, S.; Bono, A.; Krishnaiah, D.; Karali, R.; Safuan, M. K.

2017-06-01

Wax precipitation and deposition is one of the most significant flow assurance challenges in the production system of the crude oil. Wax inhibitors are developed as a preventive strategy to avoid an absolute wax deposition. Wax inhibitors are polymers which can be known as pour point depressants as they impede the wax crystals formation, growth, and deposition. In this study three formulations of wax inhibitors were prepared, ethylene vinyl acetate, ethylene vinyl acetate co-methyl methacrylate (EVA co-MMA) and ethylene vinyl acetate co-diethanolamine (EVA co-DEA) and the comparison of their efficiencies in terms of cloud point¸ pour point, performance inhibition efficiency (%PIE) and viscosity were evaluated. The cloud point and pour point for both EVA and EVA co-MMA were similar, 15°C and 10-5°C, respectively. Whereas, the cloud point and pour point for EVA co-DEA were better, 10°C and 10-5°C respectively. In conclusion, EVA co-DEA had shown the best % PIE (28.42%) which indicates highest percentage reduction of wax deposit as compared to the other two inhibitors.

Etude de faisabilite d'un systeme eolien diesel avec stockage d'air comprime

NASA Astrophysics Data System (ADS)

Benchaabane, Youssef

Le Systeme Hybride Eolien-Diesel avec Stockage d'Air Comprime (SHEDAC) utilise l'hybridation pneumatique pour remplacer la consommation des combustibles fossiles par de l'energie renouvelable, plus particulierement de l'energie eolienne. Le surplus de l'energie eolienne est utilise pour comprimer et stocker de l'air qui est utilise ensuite pour suralimenter le moteur diesel. Le memoire de maitrise est constitue de deux articles scientifiques. Le premier article presente le developpement d'un logiciel dedie a l'etude de faisabilite d'un systeme eolien-diesel avec stockage d'air comprime. Cette etude est basee sur l'analyse des couts et des revenus, des couts des equipements (eolienne, moteur diesel, systeme de stockage d'air). Elle est completee par une analyse de sensibilite aux differents parametres, une analyse des risques et des emissions des gaz a effet de serre (GES). Le deuxieme article est une application de ce logiciel pour l'installation d'un systeme SHEDAC au camp minier Esker au Quebec en remplacement des sources actuelles de production d'energie. L'utilisation du stockage d'air comprime a l'aide d'un systeme SHEDAC est le plus rentable par rapport a l'utilisation de l'energie eolienne seule ou d'une centrale thermique au diesel seule ou des deux combinees. Avec une valeur actuelle nette et un taux de rendement interne plus eleves, cette solution permet d'obtenir le plus bas cout de l'energie pour cette region eloignee. None None None

Un accumulateur echangeur de chaleur hybride pour la gestion simultanee des energies solaire et electrique

NASA Astrophysics Data System (ADS)

Ait Hammou, Zouhair

Cette etude porte sur la conception d'un accumulateur echangeur de chaleur hybride (AECH) pour la gestion simultanee des energies solaire et electrique. Un modele mathematique reposant sur les equations de conservation de la quantite d'energie est expose. Il est developpe pour tester differents materiaux de stockage, entre autres, les materiaux a changement de phase (solide/liquide) et les materiaux de stockage sensible. Un code de calcul est mis en eeuvre sur ordinateur, puis valide a l'aide des resultats analytiques et numeriques de la litterature. En parallele, un prototype experimental a echelle reduite est concu au laboratoire afin de valider le code de calcul. Des simulations sont effectuees pour etudier les effets des parametres de conception et des materiaux de stockage sur le comportement thermique de l'AECH et sur la consommation d'energie electrique. Les resultats des simulations sur quatre mois d'hiver montrent que la paraffine n-octadecane et l'acide caprique sont deux candidats souhaitables pour le stockage d'energie destine au chauffage des habitats. L'utilisation de ces deux materiaux dans l'AECH permet de reduire la consommation d'energie electrique de 32% et d'aplanir le probleme de pointe electrique puisque 90% de l'energie electrique est consommee durant les heures creuses. En plus, en adoptant un tarif preferentiel, le calcul des couts lies a la consommation d'energie electrique montre que le consommateur adoptant ce systeme beneficie d'une reduction de 50% de la facture d'electricite.

Prediction of the As-Cast Structure of Al-4.0 Wt Pct Cu Ingots

NASA Astrophysics Data System (ADS)

Ahmadein, Mahmoud; Wu, M.; Li, J. H.; Schumacher, P.; Ludwig, A.

2013-06-01

A two-stage simulation strategy is proposed to predict the as-cast structure. During the first stage, a 3-phase model is used to simulate the mold-filling process by considering the nucleation, the initial growth of globular equiaxed crystals and the transport of the crystals. The three considered phases are the melt, air and globular equiaxed crystals. In the second stage, a 5-phase mixed columnar-equiaxed solidification model is used to simulate the formation of the as-cast structure including the distinct columnar and equiaxed zones, columnar-to-equiaxed transition, grain size distribution, macrosegregation, etc. The five considered phases are the extradendritic melt, the solid dendrite, the interdendritic melt inside the equiaxed grains, the solid dendrite, and the interdendritic melt inside the columnar grains. The extra- and interdendritic melts are treated as separate phases. In order to validate the above strategy, laboratory ingots (Al-4.0 wt pct Cu) are poured and analyzed, and a good agreement with the numerical predictions is achieved. The origin of the equiaxed crystals by the "big-bang" theory is verified to play a key role in the formation of the as-cast structure, especially for the castings poured at a low pouring temperature. A single-stage approach that only uses the 5-phase mixed columnar-equiaxed solidification model and ignores the mold filling can predict satisfactory results for a casting poured at high temperature, but it delivers false results for the casting poured at low temperature.

Précipitation sélective de cations métalliques au moyen d'acide azélaïque issu de l'oxydation de l'acide oléique

NASA Astrophysics Data System (ADS)

Zimmermann, F.; Meux, E.; Oget, N.; Lecuire, J. M.; Mieloszynski, J. L.

2004-12-01

Actuellement, les métaux présents dans les effluents liquides industriels sont précipités sous forme d'hydroxydes métalliques par ajout de lait de chaux. Les boues obtenues sont dirigées vers des centres de stockage de déchets ultimes sans possibilité de valorisation. Cette étude propose comme alternative au traitement actuel, une précipitation sélective par des réactifs qui peuvent être préparés à partir d'acides carboxyliques résultant de l'oxydation de l'acide oléique présent dans les huiles végétales. Cette publication présente dans un premier temps l'oxydation de l'acide oléique par le système oxydant NaIO4/RuO4 pour l'obtention de deux acides carboxyliques. Le rendement de l'oxydation de l'acide oléique est de 100% avec production des acides pélargonïque et azélaïque qui sont facilement purifiés par recristallisation dans l’eau. Dans un deuxième temps, cette étude présente la caractérisation de différents azélates métalliques. La détermination de leur stœchiométrie conduit à des composés de type MAz pour les cations divalents et M2Az3 pour les trivalents. Des mesures de solubilités ont été réalisées pour les azélates de Fe(III), Pb(II), Zn(II), Cu(II), Ni(II) et Ca(II). La gamme de solubilité s'étend de 1,17.10-2 M pour CaAz à 1,58.10-6 M pour Fe2Az3.

Methodologie de modelisation aerostructurelle d'une aile utilisant un logiciel de calcul aerodynamique et un logiciel de calcul par elements finis =

NASA Astrophysics Data System (ADS)

Communier, David

Lors de l'etude structurelle d'une aile d'avion, il est difficile de modeliser fidelement les forces aerodynamiques subies par l'aile de l'avion. Pour faciliter l'analyse, on repartit la portance maximale theorique de l'aile sur son longeron principal ou sur ses nervures. La repartition utilisee implique que l'aile entiere sera plus resistante que necessaire et donc que la structure ne sera pas totalement optimisee. Pour pallier ce probleme, il faudrait s'assurer d'appliquer une repartition aerodynamique de la portance sur la surface complete de l'aile. On serait donc en mesure d'obtenir une repartition des charges sur l'aile beaucoup plus fiable. Pour le realiser, nous aurons besoin de coupler les resultats d'un logiciel calculant les charges aerodynamiques de l'aile avec les resultats d'un logiciel permettant sa conception et son analyse structurelle. Dans ce projet, le logiciel utilise pour calculer les coefficients de pression sur l'aile est XFLR5 et le logiciel permettant la conception et l'analyse structurelle sera CATIA V5. Le logiciel XFLR5 permet une analyse rapide d'une aile en se basant sur l'analyse de ses profils. Ce logiciel calcule les performances des profils de la meme maniere que XFOIL et permet de choisir parmi trois methodes de calcul pour obtenir les performances de l'aile : Lifting Line Theory (LLT), Vortex Lattice Method (VLM) et 3D Panels. Dans notre methodologie, nous utilisons la methode de calcul 3D Panels dont la validite a ete testee en soufflerie pour confirmer les calculs sur XFLR5. En ce qui concerne la conception et l'analyse par des elements finis de la structure, le logiciel CATIA V5 est couramment utilise dans le domaine aerospatial. CATIA V5 permet une automatisation des etapes de conception de l'aile. Ainsi, dans ce memoire, nous allons decrire la methodologie permettant l'etude aerostructurelle d'une aile d'avion.

Methodes d'amas quantiques a temperature finie appliquees au modele de Hubbard

NASA Astrophysics Data System (ADS)

Plouffe, Dany

Depuis leur decouverte dans les annees 80, les supraconducteurs a haute temperature critique ont suscite beaucoup d'interet en physique du solide. Comprendre l'origine des phases observees dans ces materiaux, telle la supraconductivite, est l'un des grands defis de la physique theorique du solide des 25 dernieres annees. L'un des mecanismes pressentis pour expliquer ces phenomenes est la forte interaction electron-electron. Le modele de Hubbard est l'un des modeles les plus simples pour tenir compte de ces interactions. Malgre la simplicite apparente de ce modele, certaines de ses caracteristiques, dont son diagramme de phase, ne sont toujours pas bien etablies, et ce malgre plusieurs avancements theoriques dans les dernieres annees. Cette etude se consacre a faire une analyse de methodes numeriques permettant de calculer diverses proprietes du modele de Hubbard en fonction de la temperature. Nous decrivons des methodes (la VCA et la CPT) qui permettent de calculer approximativement la fonction de Green a temperature finie sur un systeme infini a partir de la fonction de Green calculee sur un amas de taille finie. Pour calculer ces fonctions de Green, nous allons utiliser des methodes permettant de reduire considerablement les efforts numeriques necessaires pour les calculs des moyennes thermodynamiques, en reduisant considerablement l'espace des etats a considerer dans ces moyennes. Bien que cette etude vise d'abord a developper des methodes d'amas pour resoudre le modele de Hubbard a temperature finie de facon generale ainsi qu'a etudier les proprietes de base de ce modele, nous allons l'appliquer a des conditions qui s'approchent de supraconducteurs a haute temperature critique. Les methodes presentees dans cette etude permettent de tracer un diagramme de phase pour l'antiferromagnetisme et la supraconductivite qui presentent plusieurs similarites avec celui des supraconducteurs a haute temperature. Mots-cles : modele de Hubbard, thermodynamique, antiferromagnetisme, supraconductivite, methodes numeriques, larges matrices

Des ballons pour demain

NASA Astrophysics Data System (ADS)

Régipa, R.

A partir d'une théorie sur la détermination des formes et des contraintes globales d'un ballon de révolution, ou s'en rapprochant, une nouvelle famille de ballons a été définie. Les ballons actuels, dits de ``forme naturelle'', sont calculés en général pour une tension circonférencielle nulle. Ainsi, pour une mission donnée, la tension longitudinale et la forme de l'enveloppe sont strictement imposées. Les ballons de la nouvelle génération sont globalement cylindriques et leurs pôles sont réunis par un câble axial, chargé de transmettre une partie des efforts depuis le crochet (pôle inférieur), directement au pôle supérieur. De plus, la zone latérale cylindrique est soumise à un faible champ de tensions circonférencielles. Ainsi, deux paramètres permettent de faire évoluer la distribution des tensions et la forme de l'enveloppe: - la tension du câble de liaison entre pôles (ou la longueur de ce câble) - la tension circonférencielle moyenne désirée (ou le rayon du ballon). On peut donc calculer et réaliser: - soit des ballons de forme adaptée, comme les ballons à fond plat pour le bon fonctionnement des montgolfières infrarouge (projet MIR); - soit des ballons optimisés pour une bonne répartition des contraintes et une meilleure utilisation des matériaux d'enveloppe, pour l'ensemble des programmes stratosphériques. Il s'ensuit une économie sensible des coûts de fabrication, une fiabilité accrue du fonctionnement de ces ballons et une rendement opérationnel bien supérieur, permettant entre autres, d'envisager des vols à très haute altitude en matériaux très légers.

Facteurs d’ambiance dans l’industrie textile en République Démocratique du Congo: état de lieu

PubMed Central

Kitronza, Panda Lukongo; Philippe, Mairiaux

2016-01-01

Introduction Ce travail vise à faire une évaluation des nuisances dans le milieu de travail du secteur textile en République Démocratique du Congo. Méthodes Nous avons effectué une étude transversale et analytique. Sur 257 travailleurs sélectionnés par échantillonnage systématique, 229 travailleurs ont été retenus. 223 postes de travail ont fait l'objet de mesures pour le bruit, l'éclairage, et la chaleur. Les informations recueillies l'ont été à partir de la consultation des documents de l'entreprise, de l'interrogatoire mené par questionnaire dirigé portant essentiellement sur les renseignements socio professionnels et par des mesurages. L'analyse descriptive a été faite pour les données sociodémographiques et professionnelles et l'approche analytique pour les mesurages. Résultats Dans cette entreprise 88% des travailleurs sont des ouvriers. Le département de tissage englobe presque 68% des travailleurs. La plupart travaillent en trois pauses (85%). La population d'étude est majoritairement masculine à 85%, vieillissante avec 52% de plus de 40 ans et instruite (80%). Dans l'entreprise, seuls 12,1 % des postes de travail respectent les normes en matière de bruit et 18 % des postes en matière d'éclairage. 94% des postes ne respectent pas les normes en matière de chaleur pour un travail lourd. Conclusion Notre étude a permis de mettre en évidence les nuisances au sein de l'industrie, montrant un écart important par rapport aux normes prescrites pour les nuisances mesurées. Ces résultats est un plaidoyer pour développer des mesures de prévention appropriées. Ils sont à confronter à ceux d'autres études plus approfondies dans ce milieu. PMID:28154733

Concordance et apports de l'hystérosalpingographie et de la cœlioscopie dans l'exploration tubaire et pelvienne en cas d'infertilité

PubMed Central

Kehila, Mehdi; Ben Hmid, Rim; Ben Khedher, Sonia; Mahjoub, Sami; Channoufi, Mohamed Bedis

2014-01-01

Introduction La coelioscopie et l'hystérosalpingographie sont les deux procédures usuellement admises pour l'exploration tubaire et pelvienne en cas d'infertilité. Les objectifs de ce travail etaient de comparer les données de l'Hystérosalpingographie à celles de la coelioscopie chez des patientes explorées pour infertilité et voir l'apport de l'une par rapport à l'autre. Méthodes Etude prospective menée au service C du centre de maternité et de néonatologie de Tunis, s’étendant sur 15 mois, colligeant 120 patientes suivies pour infertilité ayant bénéficié d'une HSG suivie d'une coelioscopie. Résultats L’âge moyen de nos patientes était de 35,3 ans. L'infertilité était primaire dans 56,7% des cas et secondaire dans 43,7% des cas. Sa durée moyenne était de 48,9 mois. Le test statistique de concordance Kappa entre les 2 examens était de 0.42 pour les obstructions tubaires en général, de 0.48 pour les obstructions tubaires proximales et de 0.53 pour les obstructions tubaires distales indiquant une concordance modérée dans tous les cas. La coelioscopie a permis d'objectiver en plus une endométriose pelvienne dans 7% des cas, des adhérences pelviennes dans 33% des cas et des trompes perméables mais d'aspect pathologique dans 20% des cas. Conclusion Il existe un intérêt d′associer, chaque fois que c′est possible, l'HSG et la coelioscopie dans l'exploration du pelvis féminin dans le cadre de l'infertilité. Aucun de ces deux examens n'est parfait. Leurs résultats sont complémentaires. PMID:25374631

Prediction du profil de durete de l'acier AISI 4340 traite thermiquement au laser

NASA Astrophysics Data System (ADS)

Maamri, Ilyes

Les traitements thermiques de surfaces sont des procedes qui visent a conferer au coeur et a la surface des pieces mecaniques des proprietes differentes. Ils permettent d'ameliorer la resistance a l'usure et a la fatigue en durcissant les zones critiques superficielles par des apports thermiques courts et localises. Parmi les procedes qui se distinguent par leur capacite en terme de puissance surfacique, le traitement thermique de surface au laser offre des cycles thermiques rapides, localises et precis tout en limitant les risques de deformations indesirables. Les proprietes mecaniques de la zone durcie obtenue par ce procede dependent des proprietes physicochimiques du materiau a traiter et de plusieurs parametres du procede. Pour etre en mesure d'exploiter adequatement les ressources qu'offre ce procede, il est necessaire de developper des strategies permettant de controler et regler les parametres de maniere a produire avec precision les caracteristiques desirees pour la surface durcie sans recourir au classique long et couteux processus essai-erreur. L'objectif du projet consiste donc a developper des modeles pour predire le profil de durete dans le cas de traitement thermique de pieces en acier AISI 4340. Pour comprendre le comportement du procede et evaluer les effets des differents parametres sur la qualite du traitement, une etude de sensibilite a ete menee en se basant sur une planification experimentale structuree combinee a des techniques d'analyse statistiques eprouvees. Les resultats de cette etude ont permis l'identification des variables les plus pertinentes a exploiter pour la modelisation. Suite a cette analyse et dans le but d'elaborer un premier modele, deux techniques de modelisation ont ete considerees, soient la regression multiple et les reseaux de neurones. Les deux techniques ont conduit a des modeles de qualite acceptable avec une precision d'environ 90%. Pour ameliorer les performances des modeles a base de reseaux de neurones, deux nouvelles approches basees sur la caracterisation geometrique du profil de durete ont ete considerees. Contrairement aux premiers modeles predisant le profil de durete en fonction des parametres du procede, les nouveaux modeles combinent les memes parametres avec les attributs geometriques du profil de durete pour refleter la qualite du traitement. Les modeles obtenus montrent que cette strategie conduit a des resultats tres prometteurs.

A Workflow to Model Microbial Loadings in Watersheds ...

EPA Pesticide Factsheets

Many watershed models simulate overland and instream microbial fate and transport, but few actually provide loading rates on land surfaces and point sources to the water body network. This paper describes the underlying general equations for microbial loading rates associated with 1) land-applied manure on undeveloped areas from domestic animals; 2) direct shedding on undeveloped lands by domestic animals and wildlife; 3) urban or engineered areas; and 4) point sources that directly discharge to streams from septic systems and shedding by domestic animals. A microbial source module, which houses these formulations, is linked within a workflow containing eight models and a set of databases that form a loosely configured modeling infrastructure which supports watershed-scale microbial source-to-receptor modeling by focusing on animal-impacted catchments. A hypothetical example application – accessing, retrieving, and using real-world data – demonstrates the ability of the infrastructure to automate many of the manual steps associated with a standard watershed assessment, culminating with calibrated flow and microbial densities at the pour point of a watershed. In the Proceedings of the International Environmental Modelling and Software Society (iEMSs), 8th International Congress on Environmental Modelling and Software, Toulouse, France

Overview of Corrosion, Erosion, and Synergistic Effects of Erosion and Corrosion in the WTP Pre-treatment Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Imrich, K. J.

2015-03-27

Corrosion is an extremely complex process that is affected by numerous factors. Addition of a flowing multi-phase solution further complicates the analysis. The synergistic effects of the multiple corrosive species as well as the flow-induced synergistic effects from erosion and corrosion must be thoroughly evaluated in order to predict material degradation responses. Public domain data can help guide the analysis, but cannot reliably provide the design basis especially when the process is one-of-a-kind, designed for 40 plus years of service, and has no viable means for repair or replacement. Testing in representative simulants and environmental conditions with prototypic components willmore » provide a stronger technical basis for design. This philosophy was exemplified by the Defense Waste Processing Facility (DWPF) at the Savannah River Site and only after 15 plus years of successful operation has it been validated. There have been “hiccups”, some identified during the cold commissioning phase and some during radioactive operations, but they were minor and overcome. In addition, the system is robust enough to tolerate most flowsheet changes and the DWPF design allows minor modifications and replacements – approaches not available with the Hanford Waste Treatment Plant (WTP) “Black Cell” design methodology. Based on the available data, the synergistic effect between erosion and corrosion is a credible – virtually certain – degradation mechanism and must be considered for the design of the WTP process systems. Testing is recommended due to the number of variables (e.g., material properties, process parameters, and component design) that can affect synergy between erosion and corrosion and because the available literature is of limited applicability for the complex process chemistries anticipated in the WTP. Applicable testing will provide a reasonable and defensible path forward for design of the WTP Black Cell and Hard-to-Reach process equipment. These conclusions are consistent with findings from the various Bechtel National Inc., Independent Review Teams, and Department of Energy (DOE) reviews. A test methodology is outlined, which should provide a clear, logical road map for the testing that is necessary to provide applicable and defensible data essential to support design calculations.« less

Description of Defense Waste Processing Facility reference waste form and canister. Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baxter, R.G.

1983-08-01

The Defense Waste Processing Facility (DWPF) will be located at the Savannah River Plant in Aiken, SC, and is scheduled for construction authorization during FY-1984. The reference waste form is borosilicate glass containing approx. 28 wt % sludge oxides, with the balance glass frit. Borosilicate glass was chosen because of its high resistance to leaching by water, its relatively high solubility for nuclides found in the sludge, and its reasonably low melting temperature. The glass frit contains about 58% SiO/sub 2/ and 15% B/sub 2/O/sub 3/. Leachabilities of SRP waste glasses are expected to approach 10/sup -8/ g/m/sup 2/-day basedmore » upon 1000-day tests using glasses containing SRP radioactive waste. Tests were performed under a wide variety of conditions simulating repository environments. The canister is filled with 3260 lb of glass which occupies about 85% of the free canister volume. The filled canister will generate approx. 470 watts when filled with oxides from 5-year-old sludge and 15-year-old supernate from the sludge and supernate processes. The radionuclide content of the canister is about 177,000 ci, with a radiation level of 5500 rem/h at canister surface contact. The reference canister is fabricated of standard 24-in.-OD, Schedule 20, 304L stainless steel pipe with a dished bottom, domed head, and a combined lifting and welding flange on the head neck. The overall canister length is 9 ft 10 in. with a 3/8-in. wall thickness. The 3-m canister length was selected to reduce equipment cell height in the DWPF to a practical size. The canister diameter was selected as an optimum size from glass quality considerations, a logical size for repository handling and to ensure that a filled canister with its double containment shipping cask could be accommodated on a legal-weight truck. The overall dimensions and weight appear to be compatible with preliminary assessments of repository requirements. 10 references.« less

TRIPLICATE SODIUM IODIDE GAMMA RAY MONITORS FOR THE SMALL COLUMN ION EXCHANGE PROGRAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couture, A.

2011-09-20

This technical report contains recommendations from the Analytical Development (AD) organization of the Savannah River National Laboratory (SRNL) for a system of triplicate Sodium Iodide (NaI) detectors to be used to monitor Cesium-137 ({sup 137}Cs) content of the Decontaminated Salt Solution (DSS) output of the Small Column Ion Exchange (SCIX) process. These detectors need to be gain stabilized with respect to temperature shifts since they will be installed on top of Tank 41 at the Savannah River Site (SRS). This will be accomplished using NaI crystals doped with the alpha-emitting isotope, Americium-241({sup 241}Am). Two energy regions of the detector outputmore » will be monitored using single-channel analyzers (SCAs), the {sup 137}Cs full-energy {gamma}-ray peak and the {sup 241}Am alpha peak. The count rate in the gamma peak region will be proportional to the {sup 137}Cs content in the DSS output. The constant rate of alpha decay in the NaI crystal will be monitored and used as feedback to adjust the high voltage supply to the detector in response to temperature variation. An analysis of theoretical {sup 137}Cs breakthrough curves was used to estimate the gamma activity expected in the DSS output during a single iteration of the process. Count rates arising from the DSS and background sources were predicted using Microshield modeling software. The current plan for shielding the detectors within an enclosure with four-inch thick steel walls should allow the detectors to operate with the sensitivity required to perform these measurements. Calibration, testing, and maintenance requirements for the detector system are outlined as well. The purpose of SCIX is to remove and concentrate high-level radioisotopes from SRS salt waste resulting in two waste streams. The concentrated high-level waste containing {sup 137}Cs will be sent to the Defense Waste Processing Facility (DWPF) for vitrification and the low-level DSS will be sent to the Saltstone Production Facility (SPF) to be incorporated into grout.« less

WTP Waste Feed Qualification: Glass Fabrication Unit Operation Testing Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M. E.; Newell, J. D.; Johnson, F. C.

The waste feed qualification program is being developed to protect the Hanford Tank Waste Treatment and Immobilization Plant (WTP) design, safety basis, and technical basis by assuring waste acceptance requirements are met for each staged waste feed campaign prior to transfer from the Tank Operations Contractor to the feed receipt vessels inside the Pretreatment Facility. The Waste Feed Qualification Program Plan describes the three components of waste feed qualification: 1. Demonstrate compliance with the waste acceptance criteria 2. Determine waste processability 3. Test unit operations at laboratory scale. The glass fabrication unit operation is the final step in the processmore » demonstration portion of the waste feed qualification process. This unit operation generally consists of combining each of the waste feed streams (high-level waste (HLW) and low-activity waste (LAW)) with Glass Forming Chemicals (GFCs), fabricating glass coupons, performing chemical composition analysis before and after glass fabrication, measuring hydrogen generation rate either before or after glass former addition, measuring rheological properties before and after glass former addition, and visual observation of the resulting glass coupons. Critical aspects of this unit operation are mixing and sampling of the waste and melter feeds to ensure representative samples are obtained as well as ensuring the fabrication process for the glass coupon is adequate. Testing was performed using a range of simulants (LAW and HLW simulants), and these simulants were mixed with high and low bounding amounts of GFCs to evaluate the mixing, sampling, and glass preparation steps in shielded cells using laboratory techniques. The tests were performed with off-the-shelf equipment at the Savannah River National Laboratory (SRNL) that is similar to equipment used in the SRNL work during qualification of waste feed for the Defense Waste Processing Facility (DWPF) and other waste treatment facilities at the Savannah River Site. It is not expected that the exact equipment used during this testing will be used during the waste feed qualification testing for WTP, but functionally similar equipment will be used such that the techniques demonstrated would be applicable. For example, the mixing apparatus could use any suitable mixer capable of being remoted and achieving similar mixing speeds to those tested.« less

Analysis Of 2H-Evaporator Scale Wall [HTF-13-82] And Pot Bottom [HTF-13-77] Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oji, L. N.

2013-09-11

Savannah River Remediation (SRR) is planning to remove a buildup of sodium aluminosilicate scale from the 2H-evaporator pot by loading and soaking the pot with heated 1.5 M nitric acid solution. Sampling and analysis of the scale material has been performed so that uranium and plutonium isotopic analysis can be input into a Nuclear Criticality Safety Assessment (NCSA) for scale removal by chemical cleaning. Historically, since the operation of the Defense Waste Processing Facility (DWPF), silicon in the DWPF recycle stream combines with aluminum in the typical tank farm supernate to form sodium aluminosilicate scale mineral deposits in the 2H-evaporatormore » pot and gravity drain line. The 2H-evaporator scale samples analyzed by Savannah River National Laboratory (SRNL) came from two different locations within the evaporator pot; the bottom cone sections of the 2H-evaporator pot [Sample HTF-13-77] and the wall 2H-evaporator [sample HTF-13-82]. X-ray diffraction analysis (XRD) confirmed that both the 2H-evaporator pot scale and the wall samples consist of nitrated cancrinite (a crystalline sodium aluminosilicate solid) and clarkeite (a uranium oxyhydroxide mineral). On ''as received'' basis, the bottom pot section scale sample contained an average of 2.59E+00 {+-} 1.40E-01 wt % total uranium with a U-235 enrichment of 6.12E-01 {+-} 1.48E-02 %, while the wall sample contained an average of 4.03E+00 {+-} 9.79E-01 wt % total uranium with a U-235 enrichment of 6.03E-01% {+-} 1.66E-02 wt %. The bottom pot section scale sample analyses results for Pu-238, Pu-239, and Pu-241 are 3.16E-05 {+-} 5.40E-06 wt %, 3.28E-04 {+-} 1.45E-05 wt %, and <8.80E-07 wt %, respectively. The evaporator wall scale samples analysis values for Pu-238, Pu-239, and Pu-241 averages 3.74E-05 {+-} 6.01E-06 wt %, 4.38E-04 {+-} 5.08E-05 wt %, and <1.38E-06 wt %, respectively. The Pu-241 analyses results, as presented, are upper limit values. For these two evaporator scale samples obtained at two different locations within the evaporator pot the major radioactive components (on a mass basis) in the additional radionuclide analyses were Sr-90, Cs-137 Np-237, Pu-239/240 and Th-232. Small quantities of americium and curium were detected in the blanks used for Am/Cm method for these radionuclides. These trace radionuclide amounts are assumed to come from airborne contamination in the shielded cells drying or digestion oven, which has been replaced. Therefore, the Am/Cm results, as presented, may be higher than the true Am/Cm values for these samples. These results are provided so that SRR can calculate the equivalent uranium-235 concentrations for the NCSA. Results confirm that the uranium contained in the scale remains depleted with respect to natural uranium. SRNL did not calculate an equivalent U-235 enrichment, which takes into account other fissionable isotopes U-233, Pu-239 and Pu-241. The applicable method for calculation of equivalent U-235 will be determined in the NCSA. With a few exceptions, a comparison of select radionuclides measurements from this 2013 2H evaporator scale characterization (pot bottom and wall scale samples) with those measurements for the same radionuclides in the 2010 2H evaporator scale analysis shows that the radionuclide analysis for both years are fairly comparable; the analyses results are about the same order of magnitude.« less

Accuracy of Gypsum Casts after Different Impression Techniques and Double Pouring

PubMed Central

Silva, Stephania Caroline Rodolfo; Messias, Aion Mangino; Abi-Rached, Filipe de Oliveira; de Souza, Raphael Freitas; Reis, José Maurício dos Santos Nunes

2016-01-01

This study evaluated the accuracy of gypsum casts after different impression techniques and double pouring. Ten patients were selected and for each one it was obtained 5 partial putty/wash impressions with vinyl polysiloxane (VPS) material from teeth #13 to #16 with partial metal stock trays. The following techniques were performed: (1) one-step; two-step relief with: (2) PVC film; (3) slow-speed tungsten carbide bur and scalpel blade, (4) small movements of the tray and (5) without relief—negative control. The impressions were disinfected with 0.5% sodium hypochlorite for 10 minutes and stored during 110 and 230 minutes for the first and second pouring, respectively, with type IV gypsum. Three intra-oral lateral photographs of each patient were taken using a tripod and a customized radiographic positioner. The images were imported into ImageJ software and the total area of the buccal surface from teeth #13 to #16 was measured. A 4.0% coefficient of variance was criterion for using these measurements as Baseline values. The casts were photographed and analyzed using the same standardization for the clinical images. The area (mm2) obtained from the difference between the measurements of each gypsum cast and the Baseline value of the respective patient were calculated and analyzed by repeated-measures two way-ANOVA and Mauchly’s Sphericity test (α = 0.05). No significant effect was observed for Impression technique (P = 0.23), Second pouring (P = 0.99) and their interaction (P = 0.25). The impression techniques and double pouring did not influence the accuracy of the gypsum casts. PMID:27736967

Surface Detail Reproduction and Dimensional Stability of Contemporary Irreversible Hydrocolloid Alternatives after Immediate and Delayed Pouring.

PubMed

Kusugal, Preethi; Chourasiya, Ritu Sunil; Ruttonji, Zarir; Astagi, Preeti; Nayak, Ajay Kumar; Patil, Abhishekha

2018-01-01

To overcome the poor dimensional stability of irreversible hydrocolloids, alternative materials were introduced. The dimensional changes of these alternatives after delayed pouring are not well studied and documented in the literature. The purpose of the study is to evaluate and compare the surface detail reproduction and dimensional stability of two irreversible hydrocolloid alternatives with an extended-pour irreversible hydrocolloid at different time intervals. All testing were performed according to the ANSI/ADA specification number 18 for surface detail reproduction and specification number 19 for dimensional change. The test materials used in this study were newer irreversible hydrocolloid alternatives such as AlgiNot FS, Algin-X Ultra FS, and Kromopan 100 which is an extended pour irreversible hydrocolloid as control. The surface detail reproduction was evaluated using stereomicroscope. The dimensional change after storage period of 1 h, 24 h, and 120 h was assessed and compared between the test materials and control. The data were analyzed using one-way ANOVA and post hoc Bonferroni test. Statistically significant results ( P < 0.001) were seen when mean scores of the tested materials were compared with respect to reproduction of 22 μm line from the metal block. Kromopan 100 showed statistically significant differences between different time intervals ( P < 0.001) and exhibited more dimensional change. Algin-X Ultra FS proved to be more accurate and dimensionally stable. Newer irreversible hydrocolloid alternative impression materials were more accurate in surface detail reproduction and exhibited minimal dimensional change after storage period of 1 h, 24 h, and 120 h than extended-pour irreversible hydrocolloid impression material.

Les psychoses de l’épileptique: approche clinique à propos d'un cas

PubMed Central

Charfi, Nada; Trigui, Dorsaf; Ben Thabet, Jihène; Zouari, Nasreddine; Zouari, Lobna; Maalej, Mohamed

2014-01-01

Pour discuter les liens entre épilepsie et psychose, les auteurs rapportent l'observation d'une fille âgée de 22 ans, traitée pour épilepsie fronto-temporale, adressée en psychiatrie pour des hallucinations sensorielles et cénesthésiques et un délire mystique et d'influence, apparus secondairement et non améliorés par le traitement antiépileptique. Les symptômes psychotiques, chez l’épileptique, peuvent entrer dans le cadre de psychoses intercritiques, post-critiques ou alternatives. Pour le cas rapporté, les symptômes psychotiques étaient intercritiques et chroniques. Il s'agissait vraisemblablement d'une psychose schizophréniforme. Dans ce type de psychose, une indifférence affective et une restriction des activités sont rarement rencontrés, alors que les fluctuations rapides de l'humeur sont fréquentes. Les thématiques délirantes sont assez souvent mystiques, alimentées par des hallucinations auditives et par des hallucinations visuelles inhabituelles. Les troubles négatifs sont rares. Les psychoses épileptiques n'ont pas été identifiées comme des entités nosographiques dans les systèmes de classification psychiatrique (DSM-IV et CIM-10), ce qui pose un problème de reconnaissance de ces troubles. Une collaboration entre psychiatre et neurologue devient ainsi nécessaire pour mieux comprendre cette comorbidité complexe, éviter les erreurs diagnostiques et optimiser la prise en charge. PMID:25309665

A new portable vibrator for plaster pouring: effect on the marginal fit at cylinder-abutment

PubMed Central

de ANDRADE, Pâmela Cândida Aires Ribas; LUTHI, Leonardo Flores; STANLEY, Kyle; CARDOSO, Antônio Carlos

2012-01-01

Objective The aim of this study was to test a new portable vibrator for plaster pouring (developed for this purpose), comparing the effect of its use on the accuracy of working cast of implant-supported restorations to the conventional vibrator. Material and methods From a master cast with 2 implants, 30 transfer moldings were made randomly and divided into three groups: Group I (GI): pouring performed in an outsourced dental laboratory with conventional plaster vibrator (10 casts), Group II (GII): pouring performed in the laboratory of the Federal University of Santa Catarina (UFSC) with conventional plaster vibrator (10 casts) and Group III (GIII): pouring performed with the portable vibrator fabricated for this study (10 casts). The position of the analogue and marginal adaptation of the infrastructure were verified by testing the single screw on the master model and on the working model. The measurement of misfit was blindly performed with a precision microscope and analyzing unit, Quadra-Check 200. The data were statistically analyzed by analysis of variance (ANOVA) and the Holm-Sidak test (α=0.05). Results Means±standard deviations were as follows: GI: 19.19±4.73 µm; GII: 21.72±5.41 µm; GIII: 13.5±2.39 µm (P<0.05), with GIII significantly lower as compared to the other groups. Conclusion Within the limitations of this study, it was concluded that a greater accuracy of working cast was achieved when a portable vibrator was used for casting molds. PMID:23138736

Accuracy of Gypsum Casts after Different Impression Techniques and Double Pouring.

PubMed

Silva, Stephania Caroline Rodolfo; Messias, Aion Mangino; Abi-Rached, Filipe de Oliveira; de Souza, Raphael Freitas; Reis, José Maurício Dos Santos Nunes

2016-01-01

This study evaluated the accuracy of gypsum casts after different impression techniques and double pouring. Ten patients were selected and for each one it was obtained 5 partial putty/wash impressions with vinyl polysiloxane (VPS) material from teeth #13 to #16 with partial metal stock trays. The following techniques were performed: (1) one-step; two-step relief with: (2) PVC film; (3) slow-speed tungsten carbide bur and scalpel blade, (4) small movements of the tray and (5) without relief-negative control. The impressions were disinfected with 0.5% sodium hypochlorite for 10 minutes and stored during 110 and 230 minutes for the first and second pouring, respectively, with type IV gypsum. Three intra-oral lateral photographs of each patient were taken using a tripod and a customized radiographic positioner. The images were imported into ImageJ software and the total area of the buccal surface from teeth #13 to #16 was measured. A 4.0% coefficient of variance was criterion for using these measurements as Baseline values. The casts were photographed and analyzed using the same standardization for the clinical images. The area (mm2) obtained from the difference between the measurements of each gypsum cast and the Baseline value of the respective patient were calculated and analyzed by repeated-measures two way-ANOVA and Mauchly's Sphericity test (α = 0.05). No significant effect was observed for Impression technique (P = 0.23), Second pouring (P = 0.99) and their interaction (P = 0.25). The impression techniques and double pouring did not influence the accuracy of the gypsum casts.

Fusion of Imperfect Information in the Unified Framework of Random Sets Theory: Application to Target Identification

DTIC Science & Technology

2007-11-01

Florea, Anne-Laure Jousselme, Éloi Bossé ; DRDC Valcartier TR 2003-319 ; R & D pour la défense Canada – Valcartier ; novembre 2007. Contexte : Pour...12 3.3.2 Imprecise information . . . . . . . . . . . . . . . . . . . . . 13 3.3.3 Uncertain and imprecise information...information proposed by Philippe Smets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 5: The process of information modelling

Submarine Structure Modeling and Analysis for Life-Cycle Management: Phase 2

DTIC Science & Technology

2008-05-01

tous les emplacements de jauges extensométriques. Un certain nombre d’autres programmes FORTRAN ont également été mis au point pour incorporer dans... jauges extensométriques. Un certain nombre d’autres programmes FORTRAN ont également été mis au point pour incorporer dans les modèles par éléments

When It Rains, It Pours

ERIC Educational Resources Information Center

Mills, Linda

2012-01-01

"It's raining, it's pouring, the old man is snoring!" "The itsy, bitsy spider crawled up the waterspout, down came the rain and washed the spider out. Out came the sun and dried up all the rain, and the itsy, bitsy spider went up the spout again." What do children's nursery rhymes have to do with the school library? The author begins by telling a…

Semantics versus Statistics in the Retreat from Locative Overgeneralization Errors

ERIC Educational Resources Information Center

Ambridge, Ben; Pine, Julian M.; Rowland, Caroline F.

2012-01-01

The present study investigated how children learn that some verbs may appear in the figure-locative but not the ground-locative construction (e.g., "Lisa poured water into the cup"; "*Lisa poured the cup with water"), with some showing the opposite pattern (e.g., "*Bart filled water into the cup"; "Bart filled the cup with water"), and others…

Mental Health and Well-Being across the Military Spectrum (Bien-etre et sante mentale dans le milieu militaire)

DTIC Science & Technology

2011-04-01

il faut de toute urgence mener des actions complémentaires pour créer un environnement favorable pour l’ensemble des militaires. Dans le domaine du...changement souhaitable de comportement dans un environnement militaire de culture traditionnellement rude (macho) est un vrai défi, et il est recommandé

Prete-moi Ton Logiciel pour Ecrire un Mot (Lend Me Your Software Program So I Can Write a Letter).

ERIC Educational Resources Information Center

Mangenot, Francois

1993-01-01

A brief discussion and description of one commercially available software package ("Pour Ecrire un Mot") for writing letters of various types uses the love letter as an example of the software's functioning. Answers to the prompting questions on the screen determine the few variable parameters of the text to be generated. (four…

40 CFR 464.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... that are casting primarily gray iron where greater than 1,784 tons of metal are poured per year. PSNS... primarily gray iron where equal to or less than 1,784 tons of metal are poured per year. PSNS Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average kg/1,000 kkg (pounds per million pounds...

Effect of different conventional melt quenching technique on purity of lithium niobate (LiNbO3) nano crystal phase formed in lithium borate glass

NASA Astrophysics Data System (ADS)

Kashif, Ismail; Soliman, Ashia A.; Sakr, Elham M.; Ratep, Asmaa

2012-01-01

The glass system (45Li2O + 45B2O3 + 10Nb2O5) was fabricated by the conventional melt quenching technique poured in water, at air, between two hot plates and droplets at the cooled surface. The glass and glass ceramics were studied by differential thermal analysis (DTA) and X-ray diffraction (XRD). The as quenched samples poured in water and between two hot plates were amorphous. The samples poured at air and on cooled surface were crystalline as established via X-ray powder diffraction (XRD) studies. Differential thermal analysis was measured. The glass transition temperature (Tg) and the crystallization temperatures were calculated. Lithium niobate (LiNbO3) was the main phase in glass ceramic poured at air, droplets at the cooled surface and the heat treated glass sample at 500, 540 and 580 °C in addition to traces from LiNb3O8. Crystallite size of the main phases determined from the X-ray diffraction peaks is in the range of <100 nm. The fraction of crystalline (LiNbO3) phase decreases with increase in the heat treatment temperature.

Stoneflies of the genus Zwicknia Murányi, 2014 (Plecoptera: Capniidae) from western Switzerland.

PubMed

Reding, Jean-Paul G

2018-02-21

Le genre Zwicknia Murányi, de la famille des Capniidae, a récemment été proposé pour inclure Capnia bifrons (Newman), ce qui a rendu nécessaire la révision du matériel collecté en Suisse occidentale et identifié précédemment comme correspondant à cette espèce. Cette révision, qui a depuis abouti à la description d'une espèce nouvelle pour la science, Zwicknia ledoarei Reding et al., est maintenant complétée, permettant de signaler la présence de deux espèces supplémentaires, Z. bifrons et Z. westermanni Boumans Murányi, la dernière nouvelle pour la Suisse. Des informations sur la distribution, les préférences écologiques, la zoogéographie et le statut de conservation de ces espèces en Suisse occidentale sont également apportées. Finalement, une clé d'identification pour les larves et les adultes mâles des espèces précitées est proposée.

Appel pour une allocation intelligente dans le financement du système de santé au Cameroun

PubMed Central

Sieleunou, Isidore

2011-01-01

Le Cameroun utilise un système de budgétisation historique et une approche «top-down» pour allouer ses ressources de santé publique. Cependant, le pays compte 175 districts de santé dont les fortes disparités de nature épidémiologique, économique, géographique et culturelle, devraient être prises en compte pour réduire les iniquités en matière de sante publique. Comment comprendre alors que dans ces conditions, le budget des administrations publiques alloué aux différents districts de santé au Cameroun soit quasi identique alors que les défis sont si différents? L'inefficience allocative (mauvaise attribution du budget) générée par un tel système conduit vraisemblablement à une inefficience technique (mauvaise utilisation du budget). Pour la marche vers l'atteinte des objectifs du millénaire en matière de sante, il est impératif et urgent que les décideurs du secteur de la santé allouent de manière intelligente les ressources dans le système de santé. PMID:22355420

Formulation de cas dans la psychose débutante : Quels outils pour le travail en équipe?

PubMed Central

Elowe, Julien; Mebdouhi, Nadir; Solida, Alessandra; Conus, Philippe

2017-01-01

Nous présentons d’abord brièvement le programme TIPP et les concepts généraux de la prise en charge précoce dans la psychose débutante. Un des objectifs de l’intervention dans la phase précoce des troubles psychotiques est notamment de proposer des soins spécifiques adaptés à cette phase de la maladie. En début de prise en charge, l’équipe de soins et en particulier le gestionnaire de cas (case manager), chef d’orchestre de la prise en charge, sont confrontés à une quantité importante d’information dont il faut dégager les lignes de forces pour mettre en place une prise en charge adaptée. Cet article propose un modèle qui peut constituer un outil de travail précieux pour les équipes travaillant dans l’intervention précoce pour faire émerger une formulation de cas et synthétiser les situations cliniques des patients, en extraire une histoire qui fasse sens et ainsi faciliter la mise en place d’un projet thérapeutique. PMID:28558256

Etude des phenomenes dynamiques ultrarapides et des caracteristiques impulsionnelles d'emission terahertz du supraconducteur YBCO

NASA Astrophysics Data System (ADS)

Savard, Stephane

Les premieres etudes d'antennes a base de supraconducteurs a haute temperature critique emettant une impulsion electromagnetique dont le contenu en frequence se situe dans le domaine terahertz remontent a 1996. Une antenne supraconductrice est formee d'un micro-pont d'une couche mince supraconductrice sur lequel un courant continu est applique. Un faisceau laser dans le visible est focalise sur le micro-pont et place le supraconducteur dans un etat hors-equilibre ou des paires sont brisees. Grace a la relaxation des quasiparticules en surplus et eventuellement de la reformation des paires supraconductrices, nous pouvons etudier la nature de la supraconductivite. L'analyse de la cinetique temporelle du champ electromagnetique emis par une telle antenne terahertz supraconductrice s'est averee utile pour decrire qualitativement les caracteristiques de celle-ci en fonction des parametres d'operation tels que le courant applique, la temperature et la puissance d'excitation. La comprehension de l'etat hors-equilibre est la cle pour comprendre le fonctionnement des antennes terahertz supraconductrices a haute temperature critique. Dans le but de comprendre ultimement cet etat hors-equilibre, nous avions besoin d'une methode et d'un modele pour extraire de facon plus systematique les proprietes intrinseques du materiau qui compose l'antenne terahertz a partir des caracteristiques d'emission de celle-ci. Nous avons developpe une procedure pour calibrer le spectrometre dans le domaine temporel en utilisant des antennes terahertz de GaAs bombarde aux protons H+ comme emetteur et detecteur. Une fois le montage calibre, nous y avons insere une antenne emettrice dipolaire de YBa 2Cu3O7-delta . Un modele avec des fonctions exponentielles de montee et de descente du signal est utilise pour lisser le spectre du champ electromagnetique de l'antenne de YBa 2Cu3O7-delta, ce qui nous permet d'extraire les proprietes intrinseques de ce dernier. Pour confirmer la validite du modele choisi, nous avons mesure les proprietes intrinseques du meme echantillon de YBa2Cu3O7- delta avec la technique pompe-visible et sonde-terahertz donnant, elle aussi, acces aux temps caracteristiques regissant l'evolution hors-equilibre de ce materiau. Dans le meilleur scenario, ces temps caracteristiques devraient correspondre a ceux evalues grace a la modelisation des antennes. Un bon controle des parametres de croissance des couches minces supraconductrices et de fabrication du dispositif nous a permis de realiser des antennes d'emission terahertz possedant d'excellentes caracteristiques en terme de largeur de bande d'emission (typiquement 3 THz) exploitables pour des applications de spectroscopie resolue dans le domaine temporel. Le modele developpe et retenu pour le lissage du spectre terahertz decrit bien les caracteristiques de l'antenne supraconductrice pour tous les parametres d'operation. Toutefois, le lien avec la technique pompe-sonde lors de la comparaison des proprietes intrinseques n'est pas direct malgre que les deux techniques montrent que le temps de relaxation des porteurs augmente pres de la temperature critique. Les donnees en pompe-sonde indiquent que la mesure du temps de relaxation depend de la frequence de la sonde, ce qui complique la correspondance des proprietes intrinseques entre les deux techniques. De meme, le temps de relaxation extrait a partir du spectre de l'antenne terahertz augmente en s'approchant de la temperature critique (T c) de YBa2Cu 3O7-delta. Le comportement en temperature du temps de relaxation correspond a une loi de puissance qui est fonction de l'inverse du gap supraconducteur avec un exposant 5 soit 1/Delta 5(T). Le travail presente dans cette these permet de mieux decrire les caracteristiques des antennes supraconductrices a haute temperature critique et de les relier aux proprietes intrinseques du materiau qui les compose. De plus, cette these presente les parametres a ajuster comme le courant applique, la puissance de la pompe, la temperature d'operation, etc, afin d'optimiser l'emission et les performances de ces antennes supraconductrices entre autres pour maximiser leur etendue en frequence dans une perspective d'application en spectroscopie terahertz. Cependant, plusieurs des resultats obtenus soulevent la difficulte de decrire l'etat hors-equilibre et la necessite de developper une theorie pour le supraconducteur YBa2 Cu3O7-delta

Systeme microfluidique d'analyse sanguine en temps reel pour l'imagerie moleculaire chez le petit animal

NASA Astrophysics Data System (ADS)

Convert, Laurence

De nouveaux radiotraceurs sont continuellement développés pour améliorer l'efficacité diagnostique en imagerie moléculaire, principalement en tomographie d'émission par positrons (TEP) et en tomographie d'émission monophotonique (TEM) dans les domaines de l'oncologie, de la cardiologie et de la neurologie. Avant de pouvoir être utilisés chez les humains, ces radiotraceurs doivent être caractérisés chez les petits animaux, principalement les rats et les souris. Pour cela, de nombreux échantillons sanguins doivent être prélevés et analysés (mesure de radioactivité, séparation de plasma, séparation d'espèces chimiques), ce qui représente un défi majeur chez les rongeurs à cause de leur très faible volume sanguin (˜1,4 ml pour une souris). Des solutions fournissant une analyse partielle sont présentées dans la littérature, mais aucune ne permet d'effectuer toutes les opérations dans un même système. Les présents travaux de recherche s'insèrent dans le contexte global d'un projet visant à développer un système microfluidique d'analyse sanguine complète en temps réel pour la caractérisation des nouveaux radiotraceurs TEP et TEM. Un cahier des charges a tout d'abord été établi et a permis de fixer des critères quantitatifs et qualitatifs à respecter pour chacune des fonctions de la puce. La fonction de détection microfluidique a ensuite été développée. Un état de l'art des travaux ayant déjà combiné la microfluidique et la détection de radioactivité a permis de souligner qu'aucune solution existante ne répondait aux critères du projet. Parmi les différentes technologies disponibles, des microcanaux en résine KMPR fabriqués sur des détecteurs semiconducteurs de type p-i-n ont été identifiés comme une solution technologique pour le projet. Des détecteurs p-i-n ont ensuite été fabriqués en utilisant un procédé standard. Les performances encourageantes obtenues ont mené à initier un projet de maîtrise pour leur optimisation. En parallèle, les travaux ont été poursuivis avec des détecteurs du commerce sous forme de gaufres non découpées. Un premier dispositif intégrant des canaux en KMPR sur ces gaufres a permis de valider le concept démontrant le grand potentiel de ces choix technologiques et incitant à poursuivre les développements dans cette voie, notamment en envisageant des expériences animales. L'utilisation prolongée des canaux avec du sang non dilué est cependant particulièrement exigeante pour les matériaux artificiels. Une passivation à l'albumine a permis d'augmenter considérablement la compatibilité sanguine de la résine KMPR. Le concept initial, incluant la passivation des canaux, a ensuite été optimisé et intégré dans un système de mesure complet avec toute l'électronique et l'informatique de contrôle. Le système final a été validé chez le petit animal avec un radiotraceur connu. Ces travaux ont donné lieu à la première démonstration d'un détecteur microfluidique de haute efficacité pour la TEP et la TEM. Cette première brique d'un projet plus global est déjà un outil innovant en soi qui permettra d'augmenter l'efficacité du développement d'outils diagnostiques plus spécifiques principalement pour l'oncologie, la cardiologie et la neurologie. Mots clefs : imagerie moléculaire, tomographie d'émission par positrons (TEP), tomographie d'émission monophotonique (TEM), microfluidique, détecteur de radioactivité, KMPR, diodes p-i-n, hémocompatibilité.

Results for the First, Second, and Third Quarter Calendar Year 2015 Tank 50H WAC slurry samples chemical and radionuclide contaminants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.

2016-02-18

This report details the chemical and radionuclide contaminant results for the characterization of the Calendar Year (CY) 2015 First, Second, and Third Quarter sampling of Tank 50H for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time. Information from this characterization will be used by Defense Waste Processing Facility (DWPF) & Saltstone Facility Engineering (D&S-FE) to support the transfer of low-level aqueous waste from Tank 50H to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50H Waste Characterization System. Previous memorandamore » documenting the WAC analyses results have been issued for these three samples.« less

Digestion of Crystalline Silicotitanate (CST)

DOE Office of Scientific and Technical Information (OSTI.GOV)

DARREL, WALKER

2004-11-04

Researchers tested methods for chemically dissolving crystalline silicotitanate (CST) as a substitute for mechanical grinding to reduce particle size before vitrification. Testing used the commercially available form of CST, UOP IONSIV(R) IE-911. Reduction of the particle size to a range similar to that of the glass frit used by the Defense Waste Processing Facility (DWPF) could reduce problems with coupling cesium ion exchange to the vitrification process. This study found that IONSIV(R) IE-911 dissolves completely using a combination of acid, hydrogen peroxide, and fluoride ion. Neutralization of the resulting acidic solution precipitates components of the IONSIV(R) IE-911. Digestion requires extremelymore » corrosive conditions. Also, large particles may reform during neutralization, and the initiation and rate of gas generation are unpredictable. Therefore, the method is not recommended as a substitute for mechanical grinding.« less

Integration des sciences et de la langue: Creation et experimentation d'un modele pedagogique pour ameliorer l'apprentissage des sciences en milieu francophone minoritaire

NASA Astrophysics Data System (ADS)

Cormier, Marianne

Les faibles resultats en sciences des eleves du milieu francophone minoritaire, lors d'epreuves au plan national et international, ont interpelle la recherche de solutions. Cette these avait pour but de creer et d'experimenter un modele pedagogique pour l'enseignement des sciences en milieu linguistique minoritaire. En raison de la presence de divers degres de francite chez la clientele scolaire de ce milieu, plusieurs elements langagiers (l'ecriture, la discussion et la lecture) ont ete integres a l'apprentissage scientifique. Nous avions recommande de commencer le processus d'apprentissage avec des elements langagiers plutot informels (redaction dans un journal, discussions en dyades...) pour progresser vers des activites langagieres plus formelles (redaction de rapports ou d'explications scientifiques). En ce qui a trait a l'apprentissage scientifique, le modele preconisait une demarche d'evolution conceptuelle d'inspiration socio-constructiviste tout en s'appuyant fortement sur l'apprentissage experientiel. Lors de l'experimentation du modele, nous voulions savoir si celui-ci provoquait une evolution conceptuelle chez les eleves, et si, simultanement, le vocabulaire scientifique de ces derniers s'enrichissait. Par ailleurs, nous cherchions a comprendre comment les eleves vivaient leurs apprentissages dans le cadre de ce modele pedagogique. Une classe de cinquieme annee de l'ecole de Grande-Digue, dans le Sud-est du Nouveau-Brunswick, a participe a la mise a l'essai du modele en etudiant les marais sales locaux. Lors d'entrevues initiales, nous avons remarque que les connaissances des eleves au sujet des marais sales etaient limitees. En effet, s'ils etaient conscients que les marais etaient des lieux naturels, ils ne pouvaient pas necessairement les decrire avec precision. Nous avons egalement constate que les eleves utilisaient surtout des mots communs (plantes, oiseaux, insectes) pour decrire le marais. Les resultats obtenus indiquent que les eleves ont progresse dans leurs conceptions au sujet des marais. A la suite de l'intervention pedagogique, ils peuvent decrire le marais de facon comparable a des scientifiques en mettant a profit des mots scientifiques (spartine alterniflore, detritus, chevalier a pattes jaunes). Selon nous, les apprentissages des eleves s'expliquent surtout par la juxtaposition, dans le modele pedagogique, des elements langagiers avec une demarche de changement conceptuel a caractere experientiel. En effet, lors de cette demarche, les eleves se sont beaucoup questionnes, ont ecrit leurs reflexions, discute de leurs preoccupations et consulte des documents. Ces activites langagieres se sont deroulees directement dans le marais ainsi qu'a la suite de visites dans celui-ci. Ainsi, la possibilite de decouverte a ete reelle pour eux. Ces differents elements se sont combines pour creer une forte motivation. Le tout s'est arrime pour permettre une evolution conceptuelle et langagiere. Le modele pedagogique experimente pourrait ainsi s'averer tres fecond aupres des eleves du milieu linguistique minoritaire.

The role of economic analysis in groundwater management in semi-arid regions: the case of Nigeria

NASA Astrophysics Data System (ADS)

Acharya, Gayatri

The aim of this paper is to use an economic framework to derive decision making rules for river basin management with a focus on groundwater resources. Using an example from northern Nigeria, the paper provides an example of how decision making for sustainable water resources management may be facilitated by comparing net benefits and costs across a river basin. It is argued that economic tools can be used to assess the value of water resources in different uses, identify and analyze management scenarios, and provide decision rules for the sustainable use and management of surface and ground water resources in the region. L'objet de cet article est l'utilisation d'un cadre économique pour établir des règles de prise de décision pour la gestion d'un bassin versant prenant en compte les ressources en eau souterraine. À partir d'un exemple du Nigéria septentrional, cet article explique comment une prise de décision pour la gestion durable de ressources en eau peut être facilitée en comparant les bénéfices nets et les coûts sur tout le bassin versant. Il est montré que les outils économiques peuvent être utilisés pour établir la valeur des ressources en eau dans les différents usages, pour identifier et analyser des scénarios de gestion et pour fournir des règles de décision pour un usage et une gestion durables des ressources en eaux de surface et souterraines dans la région. El objetivo de este artículo es utilizar un enfoque económico para deducir reglas de toma de decisión en la gestión de cuencas, haciendo énfasis en los recursos subterráneos. Por medio de un ejemplo del Norte de Nigeria, se ilustra cómo la toma de decisiones orientadas a la gestión sustentable de los recursos hídricos puede ser facilitada si se compara los beneficios netos y los costes en toda la cuenca. Se argumenta que las herramientas económicas pueden servir para establecer el valor de los recursos hídricos destinados a usos diferentes, para identificar y analizar escenarios de gestión, y para proporcionar reglas de decisión que posibiliten el uso sustentable y la gestión de los recursos superficiales y subterráneos en la región.

Ingenierie de nanoparticules plasmoniques robustes pour la generation de bulles par laser en vue d'applications biomedicales

NASA Astrophysics Data System (ADS)

Lachaine, Remi

Les chirurgiens generent des bulles dans le corps humain a l'aide d'irradiation laser depuis plusieurs decennies. Ils utilisent ces bulles comme de petits scalpels, leur permettant de faire des incisions precises et localisees. Une des applications de cet outil chirurgical est la perforation cellulaire. Au lieu d'utiliser une aiguille pour perforer la membrane des cellules, il est possible de focaliser des impulsions laser en surface d'une cellule, formant un plasma au point focal du laser et generant une bulle qui perfore la membrane cellulaire. Toutefois, ce procede est assez lent et la perforation massive de cellules in-vivo n'est pas envisageable. Pour accelerer le processus, il est possible d'utiliser des nanoparticules plasmoniques. Ces dernieres agissent comme des nano-antennes qui permettent de concentrer la lumiere sur une echelle nanometrique. La possibilite d'irradier un grand nombre de nanoparticules simultanement a donne un nouvel elan a la generation de bulle comme outil de perforation cellulaire. L'utilisation de nanoparticules dans un contexte biomedical comporte toutefois certains risques. En particulier, la fragmentation de nanoparticules peut augmenter la toxicite du traitement. Dans un cas ideal, il est preferable d'utiliser des nanoparticules qui ne sont pas endommagees par l'irradiation laser. Cette these a pour but de developper une methode d'ingenierie de nanoparticules robustes permettant la generation efficace de bulles a des fins biomedicales. Il est tout d'abord demontre experimentalement que la formation de plasma est bel et bien le mecanisme physique principal menant a la generation de bulles lors de l'irradiation infrarouge (longueur d'onde de 800 nm) et ultrarapide (temps d'impulsion entre 45 fs et 1 ps) de nanoparticules d'or de 100 nm. Pour realiser cette demonstration, une methode pompe-sonde de detection de bulles d'environ 1 mum a ete elaboree. Cette methode a permis de mettre en evidence une difference de taille de 18% entre les bulles generees avec une irradiation de polarisation lineaire par rapport a une polarisation circulaire lorsque la duree d'impulsion etait inferieure a la picoseconde. Pour des impulsions plus longues, il est montre que les tailles de bulles sont independantes de la polarisation des impulsions incidentes. Ce comportement particulier est en accord avec les predictions theoriques qui incluent la formation non-lineaire de plasma et ne peut pas etre explique en considerant uniquement l'absorption des particules. Ensuite, une methode de conception de nanoparticules robustes pour la generation de bulles est elaboree. Cette methode se base sur les proprietes optiques des nanostructures.

Combat Resource Allocation Planning in Naval Engagements

DTIC Science & Technology

2007-08-01

presented and discussed in this report. The coordination problems are discussed in the companion report [2]. The developed Agent and Multi-agent-based...Technology Chef de file au Canada en matière de science et de technologie pour la défense et la sécurité nationale WWW.drdc-rddc.gc.ca Defence R&D Canada R & D pour la défense Canada

"Tele Pour Tous" in Rural Ivory Coast: Audience, Impact, Perceptions: Report of Two Surveys Conducted in January and April, 1977.

ERIC Educational Resources Information Center

Etaix, Mireille; Lenglet, Frans

This report presents the results of two surveys conducted in January and April 1977 in the Ivory Coast to assess the impact of the "Tele Pour Tous" programs on rural audiences in terms of awareness, learning, and action. Descriptions of the socio-economic characteristics of the audience and their viewing patterns were sought, and…

40 CFR 464.26 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Copper Casting Subcategory § 464.26... million pounds) of metal poured Copper (T) 0.0307 0.0168 Lead (T) 0.0211 0.0104 Zinc (T) 0.0303 0.0116 TTO... kkg (pounds per million pounds) of metal poured Copper (T) 0.928 0.506 Lead (T) 0.639 0.314 Zinc (T) 0...

Field Trial Data Analysis and Testing (FiTAT) Tool

DTIC Science & Technology

2011-10-01

amplitude/phase pour chaque antenne du réseau) contenu dans les données acquises pourrait être faite par FiTAT et utilisé dans PAASoM pour déterminer...identity matrix, k is the loop gain, φ is the correlation matrix of the incident signals and T = [1 0 . . . 0]T . The length of vector T is equal to the

40 CFR 464.46 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc Casting Subcategory § 464.46... million pounds) of metal poured Copper (T) 0.0344 0.0187 Lead (T) 0.0237 0.0116 Zinc (T) 0.0339 0.0129 TTO... million pounds) of metal poured Copper (T) 0.0066 0.0036 Lead (T) 0.0046 0.0022 Zinc (T) 0.0066 0.0025...

40 CFR 464.46 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc Casting Subcategory § 464.46... million pounds) of metal poured Copper (T) 0.0344 0.0187 Lead (T) 0.0237 0.0116 Zinc (T) 0.0339 0.0129 TTO... million pounds) of metal poured Copper (T) 0.0066 0.0036 Lead (T) 0.0046 0.0022 Zinc (T) 0.0066 0.0025...

Santé sexuelle et reproductive des adolescentes de Bobo Dioulasso, Burkina Faso: place de la communication parents-adolescentes pour la réduction des risques

PubMed Central

Some, Donmozoun Télesphore; Some, Der Adolphe; Hien, Hervé; Diallo, Ramata; Zingue, Dézémon; Diallo, Ibrahim; Diagbouga, Serge; Dao, Blami

2012-01-01

Introduction Les adolescentes sont très vulnérables face aux Infections Sexuellement Transmissibles (IST) et au VIH/SIDA. Notre étude a pour objectifs d’explorer la qualité de la communication entre les adolescentes et leurs parents sur les IST/VIH/SIDA et de recueillir leurs suggestions pour l’amélioration de cette communication. Méthodes L’étude était transversale qualitative sur 2 mois. La population de l’étude était composée par des adolescentes de 13 à 17 ans et leurs parents habitant la ville de Bobo Dioulasso. Vingt (20) adolescentes scolarisées ont été tirés au sort dans trois établissements secondaires et 20 autres non scolarisées choisies de façon accidentelle dans la ville. Les informations ont été collectées à l’aide de 8 focus groups. Les discussions ont été enregistrées sur cassettes, retranscrites en verbatim, et analysées à l’aide du logiciel QSR NVIVO 2.0. Résultats Les adolescentes et leurs parents communiquent très peu ou pas sur les questions des IST/VIH/SIDA; l’auto-information par les paires ou les médias est la première source d’information. Pour les parents, l’information existe et est accessible aux adolescentes alors que pour ces dernières, leurs connaissances de ces maladies sont parfois erronées. L’abstinence, la fidélité et le dépistage volontaire comme moyen de prévention sont très peu évoqués par les adolescentes de même que par leurs parents. Conclusion La communication parents-adolescentes est insuffisante voire absente dans certains milieux. Il est urgent de conduire des actions auprès des adolescentes et leurs parents pour mieux les informer sur les IST/VIH/SIDA et améliorer la communication sur ces maladies. PMID:22655099

Guide de pratique clinique pour les lésions cérébrales traumatiques légères et les symptômes persistants

PubMed Central

Marshall, Shawn; Bayley, Mark; McCullagh, Scott; Velikonja, Diana; Berrigan, Lindsay

2012-01-01

Résumé Objectif Présenter les nouvelles lignes directrices sur la prise en charge des lésions cérébrales traumatiques légères (LCTL) et les symptômes persistants post-commotion (SPPC) afin de renseigner et d’orienter les médecins qui prennent en charge des patients qui se remettent d’une LCTL. Qualité des données On a effectué une recherche des guides de pratique clinique existants portant sur les LCTL et une synthèse critique des ouvrages scientifiques évaluant le traitement des SPPC. Étant donné la rareté des conseils sur la prise en charge des SPPC dans les travaux sur les lésions cérébrales traumatiques, une deuxième recherche documentaire a été faite pour recenser les guides de pratique clinique et les synthèses critiques concernant la prise en charge de ces symptômes communs dans la population en général. On a convoqué des professionnels de la santé provenant de différentes disciplines et régions du Canada et de l’étranger à une conférence consensuelle d’experts pour examiner les lignes directrices et les données probantes existantes et élaborer un guide complet pour la prise en charge des LCTL et des SPPC. Message principal À l’aide d’un processus Delphi modifié, on a produit 71 recommandations portant sur le diagnostic et la prise en charge des LCTL et des SPPC. De plus, on a inclus dans le guide de nombreuses ressources et des outils pour faciliter la mise en œuvre des recommandations. Conclusion Un guide de pratique clinique a été élaboré pour aider les professionnels de la santé à fournir des soins fondés sur les données probantes et les pratiques exemplaires à la population complexe de personnes qui ont des SPPC à la suite d’une LCTL.

Surface Detail Reproduction and Dimensional Stability of Contemporary Irreversible Hydrocolloid Alternatives after Immediate and Delayed Pouring

PubMed Central

Kusugal, Preethi; Chourasiya, Ritu Sunil; Ruttonji, Zarir; Astagi, Preeti; Nayak, Ajay Kumar; Patil, Abhishekha

2018-01-01

Purpose: To overcome the poor dimensional stability of irreversible hydrocolloids, alternative materials were introduced. The dimensional changes of these alternatives after delayed pouring are not well studied and documented in the literature. The purpose of the study is to evaluate and compare the surface detail reproduction and dimensional stability of two irreversible hydrocolloid alternatives with an extended-pour irreversible hydrocolloid at different time intervals. Materials and Methods: All testing were performed according to the ANSI/ADA specification number 18 for surface detail reproduction and specification number 19 for dimensional change. The test materials used in this study were newer irreversible hydrocolloid alternatives such as AlgiNot FS, Algin-X Ultra FS, and Kromopan 100 which is an extended pour irreversible hydrocolloid as control. The surface detail reproduction was evaluated using stereomicroscope. The dimensional change after storage period of 1 h, 24 h, and 120 h was assessed and compared between the test materials and control. The data were analyzed using one-way ANOVA and post hoc Bonferroni test. Results: Statistically significant results (P < 0.001) were seen when mean scores of the tested materials were compared with respect to reproduction of 22 μm line from the metal block. Kromopan 100 showed statistically significant differences between different time intervals (P < 0.001) and exhibited more dimensional change. Algin-X Ultra FS proved to be more accurate and dimensionally stable. Conclusions: Newer irreversible hydrocolloid alternative impression materials were more accurate in surface detail reproduction and exhibited minimal dimensional change after storage period of 1 h, 24 h, and 120 h than extended-pour irreversible hydrocolloid impression material. PMID:29599578

Validation de la version française du Questionnaire de Bournemouth

PubMed Central

Martel, Johanne; Dugas, Claude; Lafond, D.; Descarreaux, M.

2009-01-01

Les auto questionnaires font partie intégrante de l’évaluation des patients ayant des douleurs cervicales. Le Questionnaire de Bournemouth intègre la réalité biopsychosociale dans l’évaluation des douleurs cervicales et sa version anglais (QBc-a) est validée et présente des propriétés psychométriques de modérées à excellentes. L’objectif de cette étude est de traduire et valider une version française de ce questionnaire. La traduction et l’adaptation a été complétée en utilisant la méthode de traduction contre-traduction qui a permis d’obtenir un consensus entre les deux versions. L’étude de validation impliquait 68 sujets (âge moyen 41 ans) qui participaient à un essai clinique randomisé concernant l’efficacité des thérapies manuelles pour les douleurs cervicales. Le protocole expérimental permettait d’obtenir des données pour évaluer la validité conceptuelle, la validité conceptuelle longitudinale, la fidélité test-retest et la sensibilité au changement. Les données de validité conceptuelle (r = 0,67 et 0,61 et 0,42 respectivement pour la validité conceptuelle pré, post traitement et longitudinale), de fidélité test-retest (r = 0,97) et de sensibilité au changement (taille de l’effet = 0,56 et réponse moyenne normalisée = 0,61) sont adéquates pour suggérer une utilisation de cet auto questionnaire pour la gestion des patients ayant des douleurs cervicales.

Fabrication et caracterisation de nanocristaux de silicium localises, realises par gravure electrochimique pour des applications nanoelectroniques

NASA Astrophysics Data System (ADS)

Ayari-Kanoun, Asma

Ce travail de these porte sur le developpement d'une nouvelle approche pour la localisation et l'organisation de nanocristaux de silicium realises par gravure electrochimique. Cette derniere represente une technique simple et peu couteuse par rapport aux autres techniques couramment utilisees pour la fabrication de nanocristaux de silicium. L'idee de ce travail a ete d'etudier la nanostructuration de minces couches de nitrure de silicium, d'environ 30 nm d'epaisseur pour permettre par la suite un arrangement periodique des nanocristaux de silicium. Cette pre-structuration est obtenue de facon artificielle en imposant un motif periodique via une technique de lithographie par faisceau d'electrons combinee avec une gravure plasma. Une optimisation des conditions de lithographie et de gravure plasma ont permis d'obtenir des reseaux de trous de 30 nm de diametre debouchant sur le silicium avec un bon controle de leur morphologie (taille, profondeur et forme). En ajustant les conditions de gravure electrochimique (concentration d'acide, temps de gravure et densite de courant), nous avons obtenu des reseaux -2D ordonnes de nanocristaux de silicium de 10 nm de diametre a travers ces masques de nanotrous avec le controle parfait de leur localisation, la distance entre les nanocristaux et leur orientation cristalline. Des etudes electriques preliminaires sur ces nanocristaux ont permis de mettre en evidence des effets de chargement. Ces resultats tres prometteurs confirment l'interet des nanocristaux de silicium realises par gravure electrochimique dans le futur pour la fabrication a grande echelle de dispositifs nanoelectroniques. Mots-cles : localisation, organisation, nanocristaux de silicium, gravure electrochimique, lithographie electronique, gravure plasma, nitrure de silicium.

Efficacy of ivermectin pour-on against Ostertagia ostertagi infection and residues in the American bison, Bison bison.

PubMed

Marley, S E; Knapp, S E; Rognlie, M C; Thompson, J R; Stoppa, T M; Button, S M; Wetzlich, S; Arndt, T; Craigmill, A

1995-01-01

Sixteen American bison, Bison bison, were artificially infected with 10(5) infective stage larvae of Ostertagia ostertagi on 21 April 1993. At 42 days post-infection eight bison were treated with 0.5% ivermectin pour-on (500 micrograms/kg bodyweight) and eight treated with the carrier only. Bison were necropsied 17 and 18 days post-treatment (21 and 22 June 1993, respectively). Mean (+/- SE) of 5,413 (+/- 1,716) adults and 565 (+/- 305) immature O. ostertagi were recovered at necropsy from bison treated with the carrier. No O. ostertagi were detected in bison treated with ivermectin pour-on. Based on the levels of the ivermectin marker metabolite in liver and adipose tissue 18 days post-treatment, the established bovine withdrawal time of 48 days appears adequate to insure that violative residues do not occur.

Review of oil families and their petroleum systems of the Williston Basin

USGS Publications Warehouse

Lillis, Paul G.

2013-01-01

Oil bulk properties such as API gravity, sulfur content, and pour point are much underutilized in the recent geochemical literature and are found to be useful here in differentiating oil families. The Red River petroleum system has two oil families that can be differentiated based on pour point. The oils in the Madison petroleum system can be divided into two families based on API gravity-sulfur content relationships, with one family derived from Type II-S kerogen and the other family derived from Type II kerogen with medium sulfur content. The Tyler petroleum system of the Williston Basin may be distinguished from the Heath-Tyler petroleum system in central Montana based on differences in geology and petroleum geochemistry, with Tyler petroleum system oils having a higher pour point and lower sulfur content.

Numerical Study of Impingement Location of Liquid Jet Poured from a Tilting Ladle with Lip Spout

NASA Astrophysics Data System (ADS)

Castilla, R.; Gamez-Montero, P. J.; Raush, G.; Khamashta, M.; Codina, E.

2017-04-01

A new approach for simulating liquid poured from a tilting lip spout is presented, using neither a dynamic mesh nor the moving solid solution method. In this case only the tilting ladle is moving, so we propose to rotate the gravitational acceleration at an angular velocity prescribed by a geometrical and dynamical calculation to keep the poured flow rate constant. This angular velocity is applied to modify the orientation of the gravity vector in computational fluid dynamics (CFD) simulations using the OpenFOAM® toolbox. Also, fictitious forces are considered. The modified solver is used to calculate the impingement location for six spout geometries and compare the jet dispersion there. This method could offer an inexpensive tool to calculate optimal spout geometries to reduce sprue size in the metal casting industry.

Impact of International Decisions of TAI Generation

DTIC Science & Technology

1996-12-01

in their specified fields as advisers on scientific and technical matters. Among them, the Coma6 Comultakifpow h D6jinition & la Seeondo (CCDS) deak...Time (UTC). For issues concerning time, the CIPM takes advice from the ComitC Consultatif pour la DCfinition de la Seconde (CCDS). Although the name...tests of new devices and suggestions to manufacturers. CONCLUSIONS The meetings of the Comite Consultatif pour la DCfinition de la Seconde gather

Integrated Airframe Design Technology (Les Technologies pour la Conception Integree des Cellules)

DTIC Science & Technology

1993-12-01

encourageant ainsi une plus forte interaction entre les organisations, ce qui laisse prevoir une ing~nierie commune concurrente pour Ia conception des...cellules. La co-localisation de personnels de diff~rentes disciplines sera n~cessaire. mais ceci pourrait se faire sous Ia forme d’une "co...integrated analysis tool Their presentation highlighted the development (e.g., ELFINI) for managing aeroelasticity, of an Aeroelastic Design

Multifunction Radar for Airborne Applications.

DTIC Science & Technology

1986-07-01

de rapport ( doo roSarvre o ntn orcp tion To de 0 & TR. Pour chaque valour de To, on calculo de la m~me faqon quo prdcdmment PS lo rIpporr - pour...senseur primordial dfalts les aviotts militaires. (in certain ttimbreC de caracteristiulues imptirtantes donne anl radar Ia supuirioritui sur Ics...muitcoroliugiques 1ironillard. nuagesi. 1estimation de distance et lestimatitin Douppler. - la sonplesse de at ]’orientatiiin ilectritnique des

Laboratory Evaluation of Australian Ration Packs.

DTIC Science & Technology

1982-09-01

Monitoring of Freeze Dried Meals , Potato & Onion Powder .......................... 40 Appendix 6 Emergency Flying Ration ............................ 41...Moulds were enumerated using the pour plate method as described in AS 1766 Part 2.1.2 1976. On occasions malt extract agar was used in place of...potato dextrose agar . Coliforms & E. coli were enumerated using the pour plate method as described in AS 1766 Part 2.1.3.7 1976. Violet red bile dextrose

Modeling of Impact Properties of Auxetic Materials: Phase 1

DTIC Science & Technology

2013-08-01

avantages marqués comparativement aux matériaux techniques classiques. La présente étude avait pour objectifs de mieux comprendre le comportement des...possible benefits of incorporating auxetic materials into lightweight armour designs . New armour designs incorporating novel auxetic materials may...Poisson négatif et ils offriraient, pour certaines applications, des avantages marqués comparativement aux matériaux techniques classiques. La présente

Introduction to Solid Rocket Propulsion

DTIC Science & Technology

2004-01-01

totally valid. Fluid-“ structure ” coupling: structure is understood here as the assembly of all the solid parts of the motor: restrictors, grain, case...Conference and Exhibit, San Diego, CA, July 12, 1995. ASSM/POP Program [10] Fonctionnement des moteurs à propergol solide segmentés pour lanceurs ...spatiaux, Colloque CNES/ONERA, Châtillon, FR, Dec. 8-9, 1992. [11] Fonctionnement des moteurs à propergol solide segmentés pour lanceurs spatiaux

Developpement d'une commande pour une hydrolienne de riviere et optimisation =

NASA Astrophysics Data System (ADS)

Tetrault, Philippe

Suivant le developpement des energies renouvelables, la presente etude se veut une base theorique quant aux principes fondamentaux necessaires au bon fonctionnement et a l'implementation d'une hydrolienne de riviere. La problematique derriere ce nouveau type d'appareil est d'abord presentee. La machine electrique utilisee dans l'application, c'est-a-dire la machine synchrone a aimants permanents, est etudiee : ses equations dynamiques mecaniques et electriques sont developpees, introduisant en meme temps le concept de referentiel tournant. Le fonctionnement de l'onduleur utilise, soit un montage en pont complet a deux niveaux a semi-conducteurs, est explique et mit en equation pour permettre de comprendre les strategies de modulation disponibles. Un bref historique de ces strategies est fait avant de mettre l'emphase sur la modulation vectorielle qui sera celle utilisee pour l'application en cours. Les differents modules sont assembles dans une simulation Matlab pour confirmer leur bon fonctionnement et comparer les resultats de la simulation avec les calculs theoriques. Differents algorithmes permettant de traquer et maintenir un point de fonctionnement optimal sont presentes. Le comportement de la riviere est etudie afin d'evaluer l'ampleur des perturbations que le systeme devra gerer. Finalement, une nouvelle approche est presentee et comparee a une strategie plus conservatrice a l'aide d'un autre modele de simulation Matlab.

Risk Factors for Developing Work-Related Musculoskeletal Disorders during Dairy Farming.

PubMed

Taghavi, Sayed Mohammad; Mokarami, Hamidreza; Ahmadi, Omran; Stallones, Lorann; Abbaspour, Asghar; Marioryad, Hossein

2017-01-01

Dairy farming work involves frequent use of poor postures. These postures may increase the risk of developing musculoskeletal disorders among dairy workers. To assess postural load during performance of various tasks related to dairy farming. This cross-sectional study was conducted on a dairy farm in Iran. In order to assess postural load, tasks related to dairy farming were divided into 3 categories: feeding, milking, and manure disposal. Each task was then divided into its constituent work subdivisions (tasks). Finally, the working posture for each work subdivision was evaluated using Rapid Entire Body Assessment (REBA). Based on the results from the REBA score, the poorest risk scores (risk level 4) were associated with the following tasks: (1) manure disposal, (2) filling feed bags, and (3) pouring milk into a bucket. Other tasks such as filling corn containers, pouring corn into the milling machine, preparing the feed, pouring food into mangers, attaching the milking machine, and pouring milk from a bucket into a tank imposed high risk (risk level 3). The risk for the tasks of washing and disinfecting the udders were assessed as medium risks. The risk levels associated with most of the tasks on the studied farm were unacceptably high. Therefore, it is essential to implement ergonomic interventions to reduce risk levels of the tasks.

On the losses of dissolved CO(2) during champagne serving.

PubMed

Liger-Belair, Gérard; Bourget, Marielle; Villaume, Sandra; Jeandet, Philippe; Pron, Hervé; Polidori, Guillaume

2010-08-11

Pouring champagne into a glass is far from being consequenceless with regard to its dissolved CO(2) concentration. Measurements of losses of dissolved CO(2) during champagne serving were done from a bottled Champagne wine initially holding 11.4 +/- 0.1 g L(-1) of dissolved CO(2). Measurements were done at three champagne temperatures (i.e., 4, 12, and 18 degrees C) and for two different ways of serving (i.e., a champagne-like and a beer-like way of serving). The beer-like way of serving champagne was found to impact its concentration of dissolved CO(2) significantly less. Moreover, the higher the champagne temperature is, the higher its loss of dissolved CO(2) during the pouring process, which finally constitutes the first analytical proof that low temperatures prolong the drink's chill and helps it to retain its effervescence during the pouring process. The diffusion coefficient of CO(2) molecules in champagne and champagne viscosity (both strongly temperature-dependent) are suspected to be the two main parameters responsible for such differences. Besides, a recently developed dynamic-tracking technique using IR thermography was also used in order to visualize the cloud of gaseous CO(2) which flows down from champagne during the pouring process, thus visually confirming the strong influence of champagne temperature on its loss of dissolved CO(2).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raszewski, F; Tommy Edwards, T; David Peeler, D

The Liquid Waste Organization (LWO) has requested that the Savannah River National Laboratory (SRNL) to assess the impact of a 100K gallon decant volume from Tank 40H on the existing sludge-only Sludge Batch 4 (SB4)-Frit 510 flowsheet and the coupled operations flowsheet (SB4 with the Actinide Removal Process (ARP)). Another potential SB4 flowsheet modification of interest includes the addition of 3 wt% sodium (on a calcined oxide basis) to a decanted sludge-only or coupled operations flowsheet. These potential SB4 flowsheet modifications could result in significant compositional shifts to the SB4 system. This paper study provides an assessment of the impactmore » of these compositional changes to the projected glass operating windows and to the variability study for the Frit 510-SB4 system. The influence of the compositional changes on melt rate was not assessed in this study nor was it requested. Nominal Stage paper study assessments were completed using the projected compositions for the various flowsheet options coupled with Frit 510 (i.e., variation was not applied to the sludge and frit compositions). In order to gain insight into the impacts of sludge variation and/or frit variation (due to the procurement specifications) on the projected operating windows, three versions of the Variation Stage assessment were performed: (1) the traditional Variation Stage assessment in which the nominal Frit 510 composition was coupled with the extreme vertices (EVs) of each sludge, (2) an assessment of the impact of possible frit variation (within the accepted frit specification tolerances) on each nominal SB4 option, and (3) an assessment of the impact of possible variation in the Frit 510 composition due to the vendor's acceptance specifications coupled with the EVs of each sludge case. The results of the Nominal Stage assessment indicate very little difference among the various flowsheet options. All of the flowsheets provide DWPF with the possibility of targeting waste loadings (WLs) from the low 30s to the low 40s with Frit 510. In general, the Tank 40H decant has a slight negative impact on the operating window, but DWPF still has the ability to target current WLs (34%) and higher WLs if needed. While the decant does not affect practical WL targets in DWPF, melt rate could be reduced due to the lower Na{sub 2}O content. If true, the addition of 3 wt% Na{sub 2}O to the glass system may regain melt rate, assuming that the source of alkali is independent of the impact on melt rate. Coupled operations with Frit 510 via the addition of ARP to the decanted SB4 flowsheet also appears to be viable based on the projected operating windows. The addition of both ARP and 3 wt% Na{sub 2}O to a decanted Tank 40H sludge may be problematic using Frit 510. Although the Nominal Stage assessments provide reasonable operating windows for the SB4 flowsheets being considered with Frit 510, introduction of potential sludge and/or frit compositional variation does have a negative impact. The magnitude of the impact on the projected operating windows is dependent on the specific flowsheet options as well as the applied variation. The results of the traditional Variation Stage assessments indicate that the three proposed Tank 40H decanted flowsheet options (Case No.2--100K gallon decant, Case No.3--100K gallon decant and 3 wt% Na{sub 2}O addition and Case No.4--100K gallon decant and ARP) demonstrate a relatively high degree of robustness to possible sludge variation over WLs of interest with Frit 510. However, the case where the addition of both ARP and 3 wt% Na{sub 2}O is considered was problematic during the traditional Variation Stage assessment. The impact of coupling the frit specifications with the nominal SB4 flowsheet options on the projected operating windows is highly dependent on whether the upper WLs are low viscosity or liquidus temperature limited in the Nominal Stage assessments. Systems that are liquidus temperature limited exhibit a high degree of robustness to the applied frit and sludge variation, while those that are low viscosity limited show significant reductions (6 percentage points) in the upper WLs that can be obtained. When both frit and sludge variations are applied, the paper study results indicate that DWPF could be severely restricted in terms of projected operating windows for the ARP and Na{sub 2}O addition options. An experimental variability study was not performed using the final SB4 composition and Frit 510 since glasses in the ComPro{trademark} data base were identified that bounded the potential operating window of this system. The bounding ARP case was not considered in that assessment. After the flowsheet cases were identified, an electronic search of ComPro{trademark} identified approximately 12 historical glasses within the compositional regions defined by at least one of the five flowsheet options, but the compositional coverage did not appear adequate to bound all cases.« less

Etude de la formation de resonances electroniques et de leur role dans la fragmentation neutre de molecules d'interet biologique

NASA Astrophysics Data System (ADS)

Lepage, Martin

1998-12-01

Cette these est presentee a la Faculte de medecine de l'Universite de Sherbrooke en vue de l'obtention du grade de Ph.D. en Radiobiologie. Elle contient des resultats experimentaux enregistres avec un spectrometre d'electrons a haute resolution. Ces resultats portent sur la formation de resonances electroniques en phase condensee et de differents canaux pour leur decroissance. En premier lieu, nous presentons des mesures d'excitations vibrationnelles de l'oxygene dilue en matrice d'argon pour des energies des electrons incidents de 1 a 20 eV. Les resultats suggerent que le temps de vie des resonances de l'oxygene est modifie par la densite d'etats d'electrons dans la bande de conduction de l'argon. Nous presentons aussi des spectres de pertes d'energie d'electrons des molecules de tetrahydrofuranne (THF) et d'acetone. Dans les deux cas, la position en energie des pertes associees aux excitations vibrationnelles est en excellent accord avec les resultats trouves dans la litterature. Les fonctions d'excitation de ces modes revelent la presence de plusieurs nouvelles resonances electroniques. Nous comparons les resonances du THF et celles de la molecule de cyclopentane en phase gazeuse. Nous proposons une origine commune aux resonances ce qui implique qu'elles ne sont pas necessairement attribuees a l'excitation des electrons non-apparies de l'oxygene du THF. Nous proposons une nouvelle methode basee sur la spectroscopie par pertes d'energie des electrons pour detecter la production de fragments neutres qui demeurent a l'interieur d'un film mince condense a basse temperature. Cette methode se base sur la detection des excitations electroniques du produit neutre. Nous presentons des resultats de la production de CO dans un film de methanol. Le taux de production de CO en fonction de l'energie incidente des electrons est calibre en termes d'une section efficace totale de diffusion des electrons. Les resultats indiquent une augmentation lineaire du taux de production de CO en fonction de l'epaisseur du film et de la dose d'electrons incidente sur le film. Ces donnees experimentales cadrent dans un modele simple ou un electron cause la fragmentation de la molecule sans reaction avec les molecules avoisinantes. Le mecanisme propose pour la fragmentation unimoleculaire du methanol est la formation de resonances qui decroissent dans un etat electronique excite. Nous suggerons l'action combinee de la presence d'un trou dans une orbitale de coeur du methanol et de la presence de deux electrons dans la premiere orbitale vide pour expliquer la dehydrogenation complete du methanol pour des energies des electrons entre 8 et 18 eV. Pour des energies plus grandes, la fragmentation par l'intermediaire de l'ionisation de la molecule a deja ete suggeree. La methode de detection des etats electroniques offre une alternative a la detection des excitations vibrationnelles puisque les spectres de pertes d'energie des electrons sont congestionnes dans cette region d'energie pour les molecules polyatomiques.

Methodologie de conception numerique d'un ventilateur helico-centrifuge basee sur l'emploi du calcul meridien

NASA Astrophysics Data System (ADS)

Lallier-Daniels, Dominic

La conception de ventilateurs est souvent basée sur une méthodologie « essais/erreurs » d'amélioration de géométries existantes ainsi que sur l'expérience de design et les résultats expérimentaux cumulés par les entreprises. Cependant, cette méthodologie peut se révéler coûteuse en cas d'échec; même en cas de succès, des améliorations significatives en performance sont souvent difficiles, voire impossibles à obtenir. Le projet présent propose le développement et la validation d'une méthodologie de conception basée sur l'emploi du calcul méridien pour la conception préliminaire de turbomachines hélico-centrifuges (ou flux-mixte) et l'utilisation du calcul numérique d'écoulement fluides (CFD) pour la conception détaillée. La méthode de calcul méridien à la base du processus de conception proposé est d'abord présentée. Dans un premier temps, le cadre théorique est développé. Le calcul méridien demeurant fondamentalement un processus itératif, le processus de calcul est également présenté, incluant les méthodes numériques de calcul employée pour la résolution des équations fondamentales. Une validation du code méridien écrit dans le cadre du projet de maîtrise face à un algorithme de calcul méridien développé par l'auteur de la méthode ainsi qu'à des résultats de simulation numérique sur un code commercial est également réalisée. La méthodologie de conception de turbomachines développée dans le cadre de l'étude est ensuite présentée sous la forme d'une étude de cas pour un ventilateur hélico-centrifuge basé sur des spécifications fournies par le partenaire industriel Venmar. La méthodologie se divise en trois étapes: le calcul méridien est employé pour le pré-dimensionnement, suivi de simulations 2D de grilles d'aubes pour la conception détaillée des pales et finalement d'une analyse numérique 3D pour la validation et l'optimisation fine de la géométrie. Les résultats de calcul méridien sont en outre comparés aux résultats de simulation pour la géométrie 3D afin de valider l'emploi du calcul méridien comme outil de prédimensionnement. Mots-clés Turbomachines hélico-centrifuges, Calcul méridien, Simulation numérique d'écoulement fluide, Conception numérique de turbomachines.

Carbon nano structures: Production and characterization

NASA Astrophysics Data System (ADS)

Beig Agha, Rosa

L'objectif de ce memoire est de preparer et de caracteriser des nanostructures de carbone (CNS -- Carbon Nanostructures, en licence a l'Institut de recherche sur l'hydrogene, Quebec, Canada), un carbone avec un plus grand degre de graphitisation et une meilleure porosite. Le Chapitre 1 est une description generale des PEMFCs (PEMFC -- Polymer Electrolyte Membrane Fuel Cell) et plus particulierement des CNS comme support de catalyseurs, leur synthese et purification. Le Chapitre 2 decrit plus en details la methode de synthese et la purification des CNS, la theorie de formation des nanostructures et les differentes techniques de caracterisation que nous avons utilises telles que la diffraction aux rayons-X (XRD -- X-ray diffraction), la microscopie electronique a transmission (TEM -- transmission electron microscope ), la spectroscopie Raman, les isothermes d'adsorption d'azote a 77 K (analyse BET, t-plot, DFT), l'intrusion au mercure, et l'analyse thermogravimetrique (TGA -- thermogravimetric analysis). Le Chapitre 3 presente les resultats obtenus a chaque etape de la synthese des CNS et avec des echantillons produits a l'aide d'un broyeur de type SPEXRTM (SPEX/CertiPrep 8000D) et d'un broyeur de type planetaire (Fritsch Pulverisette 5). La difference essentielle entre ces deux types de broyeur est la facon avec laquelle les materiaux sont broyes. Le broyeur de type SPEX secoue le creuset contenant les materiaux et des billes d'acier selon 3 axes produisant ainsi des impacts de tres grande energie. Le broyeur planetaire quant a lui fait tourner et deplace le creuset contenant les materiaux et des billes d'acier selon 2 axes (plan). Les materiaux sont donc broyes differemment et l'objectif est de voir si les CNS produits ont les memes structures et proprietes. Lors de nos travaux nous avons ete confrontes a un probleme majeur. Nous n'arrivions pas a reproduire les CNS dont la methode de synthese a originellement ete developpee dans les laboratoires de l'Institut de recherche sur l'hydrogene (IRH). Nos echantillons presentaient toujours une grande quantite de carbure de fer au detriment de la formation de nanostructures de carbone. Apres plusieurs mois de recherche nous avons constate que les metaux de base, soit le fer et le cobalt, etaient contamines. Neanmoins, ces recherches nous ont enseigne beaucoup et les resultats sont presentes aux Appendices I a III. Le carbone de depart est du charbon active commercial (CNS201) qui a ete prealablement chauffe a 1,000°C sous vide pendant 90 minutes pour se debarrasser de toute humidite et autres impuretes. En premiere etape, dans un creuset d'acier durci du CNS201 pretraite fut melange a une certaine quantite de Fe et de Co (99.9 % purs). Des proportions typiques sont 50 pd. %, 44 pd. %, et 6 pd. % pour le C, le Fe, et le Co respectivement. Pour les echantillons prepares avec le broyeur SPEX, trois a six billes en acier durci furent utilisees pour le broyage, de masse relative echantillon/poudre de 35 a 1. Pour les echantillons prepares avec le broyeur planetaire, trente-six billes en acier durci furent utilisees pour le broyage, de masse relative echantillon/poudre de 10 a 1. L'hydrogene fut alors introduit dans le creuset pour les deux types de broyeur a une pression de 1.4 MPa, et l'echantillon fut broye pendant 12 h pour le SPEX et 24 h pour le planetaire. Le broyeur SPEX a un rendement de transfert d'energie mecanique plus grand qu'un broyeur planetaire, mais il a le desavantage de contaminer davantage l'echantillon en Fe par attrition. Cependant, ceci peut etre neglige vu que le Fe etait un des catalyseurs metalliques ajoutes au creuset. En deuxieme etape, l'echantillon broye est transfere sous gaz inerte (argon) dans un tube en quartz, qui est alors chauffe a 700°C pendant 90 minutes. Des mesures de patrons de diffraction a rayons-X sur poudre furent faites pour caracteriser les changements structurels des CNS lors des etapes de synthese. Ces mesures furent prises avec un diffractometre Bruker D8 FOCUS utilisant le rayonnement Cu Ka (lambda = 1.54054 A) et une geometrie Theta/2Theta. La Figure 3.1 montre le patron de diffraction de rayon-X du charbon active utilise comme precurseur pour produire les CNS. Le charbon active est prechauffe a haute temperature (1,000°C) pendant 1 h pour enlever l'humidite. La Figure 3.2 montre les patrons de diffraction de rayons-X des echantillons SPEX et planetaire apres broyage de 12 h et 24 h, respectivement. Les structures de charbon ne sont pas encore bien definies, mais un pic a 2theta ≈ 20°-30° correspond aux petites cristallites a caractere turbostatique et un pic correspondant au fer et au carbure de fer apparait a 2theta ≈ 45°. (Abstract shortened by UMI.)

JPRS Report, Soviet Union, Political Affairs.

DTIC Science & Technology

1988-11-10

Kennedy’s visit to West Berlin had poured oil into the fire but realistic politicians knew that there were no reasons for interference. International...Semper and Neeme Ruus. In July-August 1940 eight of 11 ministers became members of the Estonian Communist Party. Decrees appointing proponents of...villages of Old Believers. We also poured a lot of oil into the flames after Lithua- nia’s liberation from the German fascists. Intimitated by those

SPERTI Reactor Pit Building (PER605) under construction. Poured concrete foundation ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SPERT-I Reactor Pit Building (PER-605) under construction. Poured concrete foundation will enclosure a "Pit" into which the reactor vessel will be placed. Steel framework has been erected. To left of view is instrument cell (PER-606), constructed of concrete block. Photographer: R.G. Larsen. Date: April 22, 1955. INEEL negative no. 55-1000 - Idaho National Engineering Laboratory, SPERT-I & Power Burst Facility Area, Scoville, Butte County, ID

Diffraction de rayons X sur les plaquettes de fer durcies par cyanuration

NASA Astrophysics Data System (ADS)

Popescu, M.; Hoyer, W.; Stegarescu, M.; Cornet, A.; Broll, N.

2004-11-01

Une méthode de cyanuration a été developpée pour les surfaces des plaquettes de fer, basée sur une réaction thermochimique qui conduit à la formation des couches dures sur le métal. Les échantillons ont été analysés, pour de temps différents de traitement, par diffraction de rayons X et par mesures de dureté.

Solutions multiples thermocapillaires en zone flottante à gravité nulle

NASA Astrophysics Data System (ADS)

Chénier, E.; Delcarte, C.; Labrosse, G.

1998-04-01

An original model is adopted to analyse the melted phase hydrodynamics, in the floating zone technique configuration for crystal growth. In particular, a small capillary scale located near the fusion fronts is taken into account. Its size turns out to influence significantly the flow structure. For the first time, multiple solutions are exhibited in zero gravity. Un modèle original a été adopté pour analyser l'hydrodynamique de la phase fondue pour la technique de la zone flottante, en croissance cristalline. En particulier, une petite échelle capillaire, située près des fronts de fusion, est prise en considération. Son extension se révèle influencer significativement la structure des écoulements. L'existence de solutions multiples est, pour la première fois, mise en évidence en gravité zéro.

Calcul numérique accéléré de mesures de performance sur les modèles Markoviens appliqués aux systèmes informatiques et de télécommunications

NASA Astrophysics Data System (ADS)

Ghaddar, A.; Sinno, N.

2005-05-01

La complexité du phénomène de files d'attente dans les systèmes informatiques et télécommunications nécessite leur simulation par des modèles Markoviens pour les mesures de performance, mesure des délais d'attente au niveau des routeurs pour le modèle informatique et l'étude de la gestion des appels téléphoniques pour le modèle des circuits téléphoniques. L'optimisation des méthodes numériques de résolution des équations relatives à ces deux modèles va permettre d' ídentifier les critères de convergence rapide vers les états stationnaires correspondant à ces mesures.

Reseaux Neuronaux Optiques

NASA Astrophysics Data System (ADS)

Bergeron, Alain

Cette recherche vise a la mise en oeuvre optique de reseaux neuronaux. Deux architectures differentes sont proposees. La premiere est la memoire associative permettant d'associer a un objet quelconque une sortie arbitraire tout en preservant l'information sur sa position. La seconde architecture, le classificateur neuronal pour le controle robotique, permet l'identification d'une entree et son classement selon differentes categories. La sortie est compatible avec les systemes numeriques standard. Pour realiser ces architectures, une approche modulaire est privilegiee. Le correlateur constitue le module de base des realisations. Differents modules sont de plus introduits pour realiser convenablement les operations neuronales. Le premier de ces modules est le seuil optoelectronique permettant de realiser une fonction non lineaire, element essentiel des reseaux neuronaux. Le second module a etre introduit est l'encodeur optonumerique, utile au classement des objets. Le probleme de l'enregistrement de la memoire est aborde a l'aide du codage iteratif global.

Propriétés optiques du silicium mésoporeux et ses applications potentielles

NASA Astrophysics Data System (ADS)

Lévy-Clément, C.; Bastide, S.

2002-04-01

Une couche de silicium poreux formée électrochimiquement à la surface de l'émetteur d'une jonction p-n+ peut jouer efficacement le rôle d'une couche antireflet pour les cellules solaires au silicium. En ajustant la densité de courant et le temps de formation, des simple et double-couches antireflet aux propriétés optiques optimisées ont pu être réalisées, conduisant à des réflectivités effectives respectives de 7.3 et 2.7 % sur l'ensemble du spectre solaire utile pour les cellules (400-1000 nm). De hauts rendements de conversion de l'énergie solaire, de l'ordre de 13-13.4 %, sont ainsi actuellement obtenus pour des cellules au silicium multicristallin avec une couche antireflet de silicium poreux.

Effets thermoelectrique et thermomagnetique du yttrium barium copper oxide monocristallin

NASA Astrophysics Data System (ADS)

Ghamlouche, Hassan

1998-09-01

Des la decouverte des supraconducteurs a haute temperature critique, les recherches se sont intensifiees afin de comprendre les mecanismes qui sont a l'origine des proprietes de ces materiaux L'etat mixte, tout comme l'etat supraconducteur pur et l'etat normal, a fait l'objet de nombreux travaux de recherche. En particulier, la structure des vortex a l'etat mixte, et leur mouvement sous l'effet d'une force quelconque, etaient et restent le centre de preoccupation. Les effets thermoelectrique (Seebeck) et thermomagnetique (Nernst) sont parmi les differentes mesures qui peuvent donner de l'information sur les etats des vortex a l'etat mixte. L'avantage essentiel de ces deux effets est l'absence d'un courant electrique applique. Ce dernier peut donner des perturbations indesirables durant les mesures. D'autre pari, nous avons utilise la methode CA (Courant Alternatif) pour effectuer nos mesures. Cette methode est caracterisee par une meilleure resolution par rapport a la methode CC (Courant Continu) conventionnelle. Nous avons etudie autant des echantillons macles que des echantillons sans macles. D'abord nous avons teste notre montage a champ magnetique nul. Nous avons alors montre que le pic rapporte par certains dans l'effet Seebeck a la transition supraconductrice ne correspond pas a une realite physique mais a un artefact experimental. On avait associe ce pic aux fluctuations. Par la suite, nous avons mis en evidence et etudie pour la premiere fois avec les effets Seebeck et Nernst le phenomene de la fusion du reseau de vortex grace a des mesures sur les echantillons sans macles. Cette etude s'est faite pour deux concentrations d'oxygene differentes et pour un gradient de temperature parallele, consecutivement, aux deux axes cristallographiques dans le plan ab. Finalement, nous avons etudie l'effet des plans de maclage sur le mouvement des vortex. Ceci a ete realise en appliquant le gradient de temperature selon trois directions differentes (0, 45 et 90°) avec les plans de maclage. Nous avons observe, pour le premier angle un mouvement libre du vortex, pour le second angle une contribution de l'effet Nernst a l'effet Seebeck et pour la troisieme direction un phenomene d'activation. Dans ce dernier cas, les plans de maclage font un obstacle qui s'oppose au mouvement des vortex. De ce qui precede, nous concluons qu'avec la bonne resolution de notre technique nous sommes capables d'observer des phenomenes que la technique CC ne met pas en relief. D'autre part, la variete d'echantillons que nous avons etudies et les phenomenes que nous avons observes valorisent la presente etude.

Navigation d'un vehicule autonome autour d'un asteroide

NASA Astrophysics Data System (ADS)

Dionne, Karine

Les missions d'exploration planetaire utilisent des vehicules spatiaux pour acquerir les donnees scientifiques qui font avancer notre connaissance du systeme solaire. Depuis les annees 90, ces missions ciblent non seulement les planetes, mais aussi les corps celestes de plus petite taille comme les asteroides. Ces astres representent un defi particulier du point de vue des systemes de navigation, car leur environnement dynamique est complexe. Une sonde spatiale doit reagir rapidement face aux perturbations gravitationnelles en presence, sans quoi sa securite pourrait etre compromise. Les delais de communication avec la Terre pouvant souvent atteindre plusieurs dizaines de minutes, il est necessaire de developper des logiciels permettant une plus grande autonomie d'operation pour ce type de mission. Ce memoire presente un systeme de navigation autonome qui determine la position et la vitesse d'un satellite en orbite autour d'un asteroide. Il s'agit d'un filtre de Kalman etendu adaptatif a trois degres de liberte. Le systeme propose se base sur l'imagerie optique pour detecter des " points de reperes " qui ont ete prealablement cartographies. Il peut s'agir de crateres, de rochers ou de n'importe quel trait physique discernable a la camera. Les travaux de recherche realises se concentrent sur les techniques d'estimation d'etat propres a la navigation autonome. Ainsi, on suppose l'existence d'un logiciel approprie qui realise les fonctions de traitement d'image. La principale contribution de recherche consiste en l'inclusion, a chaque cycle d'estimation, d'une mesure de distance afin d'ameliorer les performances de navigation. Un estimateur d'etat de type adaptatif est necessaire pour le traitement de ces mesures, car leur precision varie dans le temps en raison de l'erreur de pointage. Les contributions secondaires de recherche sont liees a l'analyse de l'observabilite du systeme ainsi qu'a une analyse de sensibilite pour six parametres principaux de conception. Les resultats de simulation montrent que l'ajout d'une mesure de distance par cycle de mise a jour entraine une amelioration significative des performances de navigation. Ce procede reduit l'erreur d'estimation ainsi que les periodes de non-observabilite en plus de contrer la dilution de precision des mesures. Les analyses de sensibilite confirment quant a elles la contribution des mesures de distance a la diminution globale de l'erreur d'estimation et ce pour une large gamme de parametres de conception. Elles indiquent egalement que l'erreur de cartographie est un parametre critique pour les performances du systeme de navigation developpe. Mots cles : Estimation d'etat, filtre de Kalman adaptatif, navigation optique, lidar, asteroide, simulations numeriques

Conception, fabrication et validation d'une presse a injection basse pression pour le procede des poudres metalliques =

NASA Astrophysics Data System (ADS)

Lamarre, Simon G.

Le moulage par injection a basse pression de poudre metallique est une technique de mise en forme de pieces de formes complexes. La poudre metallique est melangee avec des polymeres basse viscosite (ex. : cire) pour former un melange homogene a une temperature superieure a la temperature de fusion des polymeres. Pour faciliter l'injection dans la cavite du moule, la composition des melanges est ajustee pour diminuer la viscosite. D'une part, les melanges peu visqueux possedent une bonne moulabilite. D'autre part, le phenomene de la segregation se manifeste rapidement avec les melanges peu visqueux. Les machines commerciales sont munies d'un canal d'injection et d'une valve qui relient le reservoir de melange et la cavite du moule. Le melange reste stationnaire dans ces composantes entre deux sequences d'injection, ce qui le rend propice a la segregation. Plusieurs brevets tentent de resoudre ce probleme en utilisant des pompes et des canaux de recirculation. Ces composantes sont difficiles a nettoyer en raison de leur complexite. Une machine a injection basse pression a ete concue et fabriquee pour l'etude de l'aptitude au moulage des melanges de tres faible viscosite (ex. : 0.1 Pa˙s), qui tient compte du phenomene de segregation et des contraintes de nettoyage. Un piston d'injection puise le volume desire d'un reservoir. Ensuite, un mouvement lateral cisaille le melange a l'intersection entre le reservoir et le cylindre et bouche l'orifice de sortie du reservoir. Le cylindre est degage et peut recevoir le moule. A la suite de l'injection, le piston retourne a la position du reservoir et entre dans son orifice de sortie. Le melange residuel est retourne dans le reservoir, melange et desaere a nouveau. L'appareil a ete valide par des essais d'injectabilite avec un melange de poudre d'acier inoxydable et de liants a basse viscosite. Des essais d'injection ont montre que le melange contenant l'acide stearique a parcouru la plus grande distance dans le moule de forme spirale, suivi du melange contenant l'acide stearique et l'ethylene vinyle acetate et finalement du melange contenant seulement la cire de paraffine. Des essais de rheologie ont correle ces resultats pour une viscosite associee a un faible taux de cisaillement. Un essai de segregation a montre qu'un temps d'attente de moins d'une minute devait etre respecte avant de mesurer une segregation importante. De plus, le fonctionnement du systeme de vacuum a ete valide par des analyses radiographiques. Un temps de melange sous vacuum de 30 min est suffisant pour eliminer completement la presence de bulles d'air dans la piece injectee.

Optimisation des trajectoires verticales par la methode de la recherche de l'harmonie =

NASA Astrophysics Data System (ADS)

Ruby, Margaux

Face au rechauffement climatique, les besoins de trouver des solutions pour reduire les emissions de CO2 sont urgentes. L'optimisation des trajectoires est un des moyens pour reduire la consommation de carburant lors d'un vol. Afin de determiner la trajectoire optimale de l'avion, differents algorithmes ont ete developpes. Le but de ces algorithmes est de reduire au maximum le cout total d'un vol d'un avion qui est directement lie a la consommation de carburant et au temps de vol. Un autre parametre, nomme l'indice de cout est considere dans la definition du cout de vol. La consommation de carburant est fournie via des donnees de performances pour chaque phase de vol. Dans le cas de ce memoire, les phases d'un vol complet, soit, une phase de montee, une phase de croisiere et une phase de descente, sont etudies. Des " marches de montee " etaient definies comme des montees de 2 000ft lors de la phase de croisiere sont egalement etudiees. L'algorithme developpe lors de ce memoire est un metaheuristique, nomme la recherche de l'harmonie, qui, concilie deux types de recherches : la recherche locale et la recherche basee sur une population. Cet algorithme se base sur l'observation des musiciens lors d'un concert, ou plus exactement sur la capacite de la musique a trouver sa meilleure harmonie, soit, en termes d'optimisation, le plus bas cout. Differentes donnees d'entrees comme le poids de l'avion, la destination, la vitesse de l'avion initiale et le nombre d'iterations doivent etre, entre autre, fournies a l'algorithme pour qu'il soit capable de determiner la solution optimale qui est definie comme : [Vitesse de montee, Altitude, Vitesse de croisiere, Vitesse de descente]. L'algorithme a ete developpe a l'aide du logiciel MATLAB et teste pour plusieurs destinations et plusieurs poids pour un seul type d'avion. Pour la validation, les resultats obtenus par cet algorithme ont ete compares dans un premier temps aux resultats obtenus suite a une recherche exhaustive qui a utilisee toutes les combinaisons possibles. Cette recherche exhaustive nous a fourni l'optimal global; ainsi, la solution de notre algorithme doit se rapprocher le plus possible de la recherche exhaustive afin de prouver qu'il donne des resultats proche de l'optimal global. Une seconde comparaison a ete effectuee entre les resultats fournis par l'algorithme et ceux du Flight Management System (FMS) qui est un systeme d'avionique situe dans le cockpit de l'avion fournissant la route a suivre afin d'optimiser la trajectoire. Le but est de prouver que l'algorithme de la recherche de l'harmonie donne de meilleurs resultats que l'algorithme implemente dans le FMS.

Caracterisation des melanges developpes pour le moulage basse pression des poudres metalliques (LPIM) =

NASA Astrophysics Data System (ADS)

Fareh, Fouad

Le moulage par injection basse pression des poudres metalliques est une technique de fabrication qui permet de fabriquer des pieces possedant la complexite des pieces coulees mais avec les proprietes mecaniques des pieces corroyees. Cependant, l'optimisation des etapes de deliantage et de frittage a ete jusqu'a maintenant effectuee a l'aide de melange pour lesquels la moulabilite optimale n'a pas encore ete demontree. Ainsi, la comprehension des proprietes rheologiques et de la segregation des melanges est tres limitee et cela presente le point faible du processus de LPIM. L'objectif de ce projet de recherche etait de caracteriser l'influence des liants sur le comportement rheologique des melanges en mesurant la viscosite et la segregation des melanges faible viscosite utilises dans le procede LPIM. Afin d'atteindre cet objectif, des essais rheologiques et thermogravimetriques ont ete conduits sur 12 melanges. Ces melanges ont ete prepares a base de poudre d'Inconel 718 de forme spherique (chargement solide constant a 60%) et de cires, d'agents surfactants ou epaississants. Les essais rheologiques ont ete utilises entre autre pour calculer l'indice d'injectabilite ?STV des melanges, tandis que les essais thermogravimetriques ont permis d'evaluer precisement la segregation des poudres dans les melanges. Il a ete demontre que les trois (3) melanges contenant de la cire de paraffine et de l'acide stearique presentent des indices alpha STV plus eleves qui sont avantageux pour le moulage par injection des poudres metalliques (MIM), mais segregent beaucoup trop pour que la piece fabriquee produise de bonnes caracteristiques mecaniques. A l'oppose, le melange contenant de la cire de paraffine et de l'ethylene-vinyle acetate ainsi que le melange contenant seulement de la cire de carnauba segregent peu voire pas du tout, mais possedent de tres faibles indices alphaSTV : ils sont donc difficilement injectables. Le meilleur compromis semble donc etre les melanges contenant de la cire (de paraffine, d'abeille et de carnauba) et de faible teneur en acide stearique et en ethylene-vinyle acetate. Par ailleurs, les lois physiques preexistantes ont permis de confirmer les resultats des essais rheologiques et thermogravimetriques, mais aussi de mettre en evidence l'influence de la segregation sur les proprietes rheologiques des melanges. Ces essais ont aussi montre l'effet de constituants de liant et du temps passe a l'etat fondu sur l'intensite de la segregation dans les melanges. Les melanges contenants de l'acide stearique segregent rapidement. La caracterisation des melanges developpes pour le moulage basse pression des poudres metalliques doit etre obtenue a l'aide d'une methode de courte duree pour eviter la segregation et de mesurer precisement l'aptitude a l'ecoulement de ces melanges.

Conception et calibration d'un sonoreacteur pour l'oxydation de la cellulose par le systeme TEMPO/NaOCl/NaBr

NASA Astrophysics Data System (ADS)

Paquin, Michel

Avec le contexte economique actuel dans le domaine des pates et papiers au Canada, l'industrie se doit de diversifier ses produits mis en marche. La fermeture de plus de 20 usines depuis 2005, une baisse du PIB de l'industrie de 1,4 milliard CAD entre 1999--2008, une baisse de la demande de 2,4 %, une diminution du prix de la pate de 20,9 % depuis juillet 2009. La delocalisation du secteur vers l'Asie et l'hemisphere sud sont autant de raisons pour laquelle l'industrie se doit d'etre a l'avant plan de nouvelle technologie a base de fibre de bois. Pour augmenter leur rentabilite, l'industrie se doit de diversifier ses produits dans d'autres secteurs que le simple fabricant de papier impression-ecriture. Sa diversification passe par l'elaboration de nouveaux papiers a valeur ajoutee (papier conducteur, papier bioactif, etc.), par l'utilisation de la biomasse forestiere pour la production d'energie, par l'utilisation de la biomasse forestiere pour l'elaboration d'une plateforme de chimie verte, par l'utilisation de la lignine pour le developpement de polymeres et par l'utilisation de la fibre cellulosique pour la fabrication de nanomateriaux. La fabrication de nanofibrille de cellulose peut devenir un des produits qui servira a diversifier la production des usines de pates et papiers. Les nanofibrilles de cellulose possedent des proprietes mecaniques et chimiques exceptionnelles. Les nanofibrilles de cellulose sont fabriquees a partir d'une oxydation selective de la pate kraft de feuillu avec le systeme TEMPO-NaOCl-NaBr. L'oxydation selective de l'alcool primaire en C6 du monomere de glucose sous forme de carboxylates engendre une modification chimique de la cellulose qui accroit l'hydrophilicite des fibrilles. Suite a cette oxydation, nous devons effectuer une desintegration mecanique de la fibre kraft de feuillu oxydee pour separer les fibrilles. Le processus d'oxydation de la fibre par le systeme TEMPO-NaOCl-NaBr et sa defibrillation par la suite engendre une grande consommation d'energie et de reactif qui rend le procede difficilement accessible au milieu industriel. L'utilisation des ultrasons lors de la reaction d'oxydation permet de reduire de 50% le temps de reaction et d'autant la consommation de produits chimiques. Actuellement le processus d'oxydation s'effectue en mode discontinu pour une quantite de 20 grammes de pate dans un reacteur en verre dans un bain a ultrason. L'objectif principal de ce travail est d'elaborer un sonoreacteur en mode semi-continu afin d'etre en mesure de transferer une reaction d'oxydation du mode discontinu en mode semi-continu. Le transfert de reaction sera effectue en realisant la calibration de l'activite acoustique des deux differents reacteurs, discontinu et semi-continu, par la methode de Weissler. La methode de Weissler quantifie le taux de production radicalaire en mesurant la formation d'iode moleculaire d'une solution aqueuse d'iodure de potassium sous ultrason. Suite a sa calibration, le sonoreacteur pilote (mode semi-continu) a demontre une augmentation de la production radicalaire de 683 % a 170 kHz en comparaison avec l'utilisation d'un bain a ultrason a la meme frequence. Lors de la reaction d'oxydation, la puissance optimale utilisee dans le bain a ultrason a 170 kHz est de 1000 W. La puissance utilisee selon les resultats de calibration obtenue dans le sonoreacteur pilote est de 125 W soit une diminution de l'energie appliquee de 87,5 %. Lors de la reaction d'oxydation, le taux de production des groupements carboxylates est de 2,6 mmol COOH kg/min dans le bain a ultrason et de 6,87 mmol COOH kg/min dans le sonoreacteur pilote soit une augmentation de 164% du taux de formation. Selon les resultats obtenus, l'utilisation d'un sonoreacteur en mode continu peut etre envisageable pour la reaction d'oxydation de la cellulose par le systeme TEMPO-NaOCl-NaBr en industrie au niveau industriel.

Impedance de surface dans les supraconducteurs quasi-bidimensionnels

NASA Astrophysics Data System (ADS)

Achkir, Driss Brice

Ce travail a caractere experimental et theorique vise l'etude de l'etat supraconducteur de trois familles de composes: les supraconducteurs conventionnels, les organiques et les cuprates YBCO. Pour ce faire, nous avons utilise une technique hyperfrequence, a savoir la mesure d'impedance de surface en fonction de la temperature et du champ magnetique. Dans les supraconducteurs conventionnels, nous avons mesure pour la premiere fois le pic de "coherence" dans la partie reelle de la conductivite. Bien que predit par la theorie BCS, ce pic n'avait pas ete clairement observe en raison de difficultes techniques liees a ce type d'experience. D'autre part, la theorie d'Eliashberg appliquee a la partie reelle de la conductivite du niobium nous a revele l'importance des mesures hyperfrequences pour mieux extraire la partie basse frequence de la densite spectrale alphasp2F(omega). Cette possibilite est attrayante puisque c'est precisement la region de frequences de alphasp2F(omega) ou les donnees d'effet tunnel sont imprecises. Les resultats obtenus sur la longueur de penetration dans les organiques et les cuprates ont permis de montrer que le gap presente des lignes de zeros au niveau de Fermi ou qu'il est, a tout le moins, fortement anisotrope. En effet, la dependance en temperature de la longueur de penetration dans les cristaux purs est lineaire a basse temperature et elle devient quadratique dans les cristaux dopes. Pour le cas des supraconducteurs organiques quasi-bidimensionnels (Et)sb2X, nous avons aussi observe un maximum sur la partie reelle de la conductivite qui n'a rien a voir avec un pic de coherence. Pour ces composes, nous avons effectue une des toutes premieres etudes des fluctuations supraconductrices en temperature et en champ magnetique. Nous montrons que la paraconductivite sigmasp' due aux fluctuations presente un comportement de type Aslamazov-Larkin de nature tridimensionnelle. Ces mesures sont appuyees par les resultats theoriques d'un modele Ginzburg-Landau dynamique que nous avons developpe. De plus, a partir de l'analyse des fluctuations, nous avons pu identifier le champ critique pour la transition resistive en champ et ainsi en deduire la transition de fonte du reseau de vortex dans le (Et)sb2Cu(SCN)sb2.

Elaboration de nouvelles approches micromecaniques pour l'optimisation des performances mecaniques des materiaux heterogenes

NASA Astrophysics Data System (ADS)

Aboutajeddine, Ahmed

Les modeles micromecaniques de transition d'echelles qui permettent de determiner les proprietes effectives des materiaux heterogenes a partir de la microstructure sont consideres dans ce travail. L'objectif est la prise en compte de la presence d'une interphase entre la matrice et le renforcement dans les modeles micromecaniques classiques, de meme que la reconsideration des approximations de base de ces modeles, afin de traiter les materiaux multiphasiques. Un nouveau modele micromecanique est alors propose pour tenir compte de la presence d'une interphase elastique mince lors de la determination des proprietes effectives. Ce modele a ete construit grace a l'apport de l'equation integrale, des operateurs interfaciaux de Hill et de la methode de Mori-Tanaka. Les expressions obtenues pour les modules globaux et les champs dans l'enrobage sont de nature analytique. L'approximation de base de ce modele est amelioree par la suite dans un nouveau modele qui s'interesse aux inclusions enrobees avec un enrobage mince ou epais. La resolution utilisee s'appuie sur une double homogeneisation realisee au niveau de l'inclusion enrobee et du materiau. Cette nouvelle demarche, permettra d'apprehender completement les implications des approximations de la modelisation. Les resultats obtenus sont exploites par la suite dans la solution de l'assemblage de Hashin. Ainsi, plusieurs modeles micromecaniques classiques d'origines differentes se voient unifier et rattacher, dans ce travail, a la representation geometrique de Hashin. En plus de pouvoir apprecier completement la pertinence de l'approximation de chaque modele dans cette vision unique, l'extension correcte de ces modeles aux materiaux multiphasiques est rendue possible. Plusieurs modeles analytiques et explicites sont alors proposee suivant des solutions de differents ordres de l'assemblage de Hashin. L'un des modeles explicite apparait comme une correction directe du modele de Mori-Tanaka, dans les cas ou celui ci echoue a donner de bons resultats. Finalement, ce modele de Mori-Tanaka corrige est utilise avec les operateurs de Hill pour construire un modele de transition d'echelle pour les materiaux ayant une interphase elastoplastique. La loi de comportement effective trouvee est de nature incrementale et elle est conjuguee a la relation de la plasticite de l'interphase. Des simulations d'essais mecaniques pour plusieurs proprietes de l'interphase plastique a permis de dresser des profils de l'enrobage octroyant un meilleur comportement au materiau.

Performance du GeneXpert MTB/RIF® dans le diagnostic de la tuberculose extra-pulmonaire à Dakar: 2010-2015

PubMed Central

Diallo, Awa Ba; Kollo, Abdoulkader Issifi; Camara, Makhtar; Lo, Seynabou; Ossoga, Gedeon Walbang; Mbow, Moustapha; Karam, Farba; Niang, Mame Yacine Fall; Thiam, Aliou; Diawara, Awa Ndiaye; Mboup, Souleymane; Diallo, Aissatou Gaye

2016-01-01

Introduction Le défi des pays en voie de développement est la disponibilité de méthodes de diagnostic rapide et précis pour le management de la tuberculose. Des techniques moléculaires offrent cet avantage et nous avons utilisé le test GeneXpert MTB/RIF dans le diagnostic de la tuberculose extra-pulmonaire pour évaluer sa performance par rapport aux méthodes conventionnelles. Méthodes Entre 2010 et 2015, 544 échantillons cliniques extra-pulmonaires ont été recueillis et traitées par la microscopie, la culture et le GeneXpert. L'étude de la sensibilité aux antituberculeux a été effectué avec le MGIT 960. Le Génotype MTBDRplus a été utilisé pour confirmer les cas de résistance à la rifampicine détectés par le système GX. Résultats La population d'étude de 544 patients incluait 55,15% d'hommes et 44,85% de femmes. L'âge des patients variait entre 1 à 92 avec la majorité dans le groupe d'âge 18-45 ans. La sensibilité et la spécificité globale de la microscopie étaient de 43,86% et 98,36%, et pour le GeneXpert® 94,74% et 97,95% respectivement avec 95% IC. Deux résultats de résistance à la rifampicine discordants ont été trouvées entre le test GeneXpert et la méthode phénotypique. Les résultats du test MTBDRplus ont montré une concordance de 100% avec ceux du MGIT 960 pour les cas discordants de résistance à la rifampicine. Conclusion Cette étude a montré que le test GeneXpert a une plus grande sensibilité pour le diagnostic de routine de la tuberculose extra-pulmonaire et devrait être utilisé à la place de la microscopie. Les cas de résistance à la rifampicine détectés par le GeneXpert doivent être confirmés par d'autres tests moléculaires avant d'initier un traitement. PMID:28292091

Caracterisation des revetements par projection thermique a haute vitesse obtenus a partir de differentes poudres de wc-10co-4cr pour des applications en aeronautique =

NASA Astrophysics Data System (ADS)

Quintero Malpica, Alfonso

Les revetements par projection thermique HVOF (High Velocity Oxy-Fuel) sont communement utilises dans l'industrie aeronautique, notamment au sein du partenaire industriel du projet (Tecnickrome Aeronautique Inc), comme des remplacants pour les revetements produits par l'electrodeposition du chrome dur due aux problemes environnementaux. Ce projet avait pour but de trouver une poudre alternative a celle qui est actuellement utilisee pour la production des revetements de type WC-10Co-4Cr obtenus avec la technologie de projection thermique a haute vitesse HVOF et en utilisant le systeme de projection HVOF-JET KOTERTM III. Dans un premier temps, cinq poudres incluant celle de reference, ayant des distributions granulometriques differentes, ont ete projetees dans le but d'identifier quelles poudres pouvaient etre utilisees avec le systeme de projection HVOF-JET KOTERTM III en gardant des parametres similaires (debit d'hydrogene, debit d'oxygene, debit de poudre et distance de projection) que pour la poudre de reference. Les revetements obtenus a partir des poudres etudiees ont ete evalues selon les criteres d'acceptation des revetements sollicites par les principaux manufacturiers des trains d'atterrissage. Les tests ont porte sur l'epaisseur, l'adhesion, la microstructure, la microdurete, les contraintes residuelles et la rugosite. A partir des resultats obtenus, seulement deux poudres ont rencontre toutes les proprietes demandees par les specifications aeronautiques. L'influence de la variation de la distance de projection sur la qualite des revetements a ete etudiee. Cinq distances (100, 125, 150, 175 et 200 mm) ont ete choisies pour faire la projection des deux poudres selectionnees. Les revetements obtenus ont montre de proprietes des revetements similaires (epaisseur, adhesion, microstructure, microdurete, contraintes residuelles et rugosite). Il a ete trouve que la distance de projection est un parametre indirect du systeme de projection HVOF-JET KOTERTM III et qu'autant la vitesse que la temperature des particules semblent mieux determiner les proprietes du revetement, en particulier, les niveaux de contraintes residuelles finales dans les revetements. Lorsque les revetements sont produits a de courtes distances de projection, les particules arrivent avec plus grande vitesse et temperature ce qui resulte dans de plus grandes temperatures du substrat et plus grande energie d'impact, resultant dans de plus grandes contraintes residuelles de compression dans les revetements.

Modelisation frequentielle de la permittivite du beton pour le controle non destructif par georadar

NASA Astrophysics Data System (ADS)

Bourdi, Taoufik

Le georadar (Ground Penetrating Radar (GPR)) constitue une technique de controle non destructif (CND) interessante pour la mesure des epaisseurs des dalles de beton et la caracterisation des fractures, en raison de ses caracteristiques de resolution et de profondeur de penetration. Les equipements georadar sont de plus en plus faciles a utiliser et les logiciels d'interpretation sont en train de devenir plus aisement accessibles. Cependant, il est ressorti dans plusieurs conferences et ateliers sur l'application du georadar en genie civil qu'il fallait poursuivre les recherches, en particulier sur la modelisation et les techniques de mesure des proprietes electriques du beton. En obtenant de meilleures informations sur les proprietes electriques du beton aux frequences du georadar, l'instrumentation et les techniques d'interpretation pourraient etre perfectionnees plus efficacement. Le modele de Jonscher est un modele qui a montre son efficacite dans le domaine geophysique. Pour la premiere fois, son utilisation dans le domaine genie civil est presentee. Dans un premier temps, nous avons valide l'application du modele de Jonscher pour la caracterisation de la permittivite dielectrique du beton. Les resultats ont montre clairement que ce modele est capable de reproduire fidelement la variation de la permittivite de differents types de beton sur la bande de frequence georadar (100 MHz-2 GHz). Dans un deuxieme temps, nous avons montre l'interet du modele de Jonscher en le comparant a d'autres modeles (Debye et Debye-etendu) deja utilises dans le domaine genie civil. Nous avons montre aussi comment le modele de Jonscher peut presenter une aide a la prediction de l'efficacite de blindage et a l'interpretation des ondes de la technique GPR. Il a ete determine que le modele de Jonscher permet de donner une bonne presentation de la variation de la permittivite du beton dans la gamme de frequence georadar consideree. De plus, cette modelisation est valable pour differents types de beton et a differentes teneurs en eau. Dans une derniere partie, nous avons presente l'utilisation du modele de Jonscher pour l'estimation de l'epaisseur d'une dalle de beton par la technique GPR dans le domaine frequentiel. Mots-cles : CND, beton, georadar , permittivite, Jonscher

Techniques d'inspection par ondes guidees ultrasonores d'assemblages brases dans des reacteurs aeronautiques =

NASA Astrophysics Data System (ADS)

Comot, Pierre

L'industrie aeronautique, cherche a etudier la possibilite d'utiliser de maniere structurelle des joints brases, dans une optique de reduction de poids et de cout. Le developpement d'une methode d'evaluation rapide, fiable et peu couteuse pour evaluer l'integrite structurelle des joints apparait donc indispensable. La resistance mecanique d'un joint brase dependant principalement de la quantite de phase fragile dans sa microstructure. Les ondes guidees ultrasonores permettent de detecter ce type de phase lorsqu'elles sont couplees a une mesure spatio-temporelle. De plus la nature de ce type d'ondes permet l'inspection de joints ayant des formes complexes. Ce memoire se concentre donc sur le developpement d'une technique basee sur l'utilisation d'ondes guidees ultrasonores pour l'inspection de joints brases a recouvrement d'Inconel 625 avec comme metal d'apport du BNi-2. Dans un premiers temps un modele elements finis du joint a ete utilise pour simuler la propagation des ultrasons et optimiser les parametres d'inspection, la simulation a permis egalement de demontrer la faisabilite de la technique pour la detection de la quantite de phase fragile dans ce type de joints. Les parametres optimises sont la forme de signal d'excitation, sa frequence centrale et la direction d'excitation. Les simulations ont montre que l'energie de l'onde ultrasonore transmise a travers le joint aussi bien que celle reflechie, toutes deux extraites des courbes de dispersion, etaient proportionnelles a la quantite de phase fragile presente dans le joint et donc cette methode permet d'identifier la presence ou non d'une phase fragile dans ce type de joint. Ensuite des experimentations ont ete menees sur trois echantillons typiques presentant differentes quantites de phase fragile dans le joint, pour obtenir ce type d'echantillons differents temps de brasage ont ete utilises (1, 60 et 180 min). Pour cela un banc d'essai automatise a ete developpe permettant d'effectuer une analyse similaire a celle utilisee en simulation. Les parametres experimentaux ayant ete choisis en accord avec l'optimisation effectuee lors des simulations et apres une premiere optimisation du procede experimental. Finalement les resultats experimentaux confirment les resultats obtenus en simulation, et demontrent le potentiel de la methode developpee.

Etude aerodynamique d'un jet turbulent impactant une paroi concave

NASA Astrophysics Data System (ADS)

LeBlanc, Benoit

Etant donne la demande croissante de temperatures elevees dans des chambres de combustion de systemes de propulsions en aerospatiale (turbomoteurs, moteur a reaction, etc.), l'interet dans le refroidissement par jets impactant s'est vu croitre. Le refroidissement des aubes de turbine permet une augmentation de temperature de combustion, ce qui se traduit en une augmentation de l'efficacite de combustion et donc une meilleure economie de carburant. Le transfert de chaleur dans les au bages est influence par les aspects aerodynamiques du refroidissement a jet, particulierement dans le cas d'ecoulements turbulents. Un manque de comprehension de l'aerodynamique a l'interieur de ces espaces confinees peut mener a des changements de transfert thermique qui sont inattendus, ce qui augmente le risque de fluage. Il est donc d'interet pour l'industrie aerospatiale et l'academie de poursuivre la recherche dans l'aerodynamique des jets turbulents impactant les parois courbes. Les jets impactant les surfaces courbes ont deja fait l'objet de nombreuses etudes. Par contre des conditions oscillatoires observees en laboratoire se sont averees difficiles a reproduire en numerique, puisque les structures d'ecoulements impactants des parois concaves sont fortement dependantes de la turbulence et des effets instationnaires. Une etude experimentale fut realisee a l'institut PPRIME a l'Universite de Poitiers afin d'observer le phenomene d'oscillation dans le jet. Une serie d'essais ont verifie les conditions d'ecoulement laminaires et turbulentes, toutefois le cout des essais experimentaux a seulement permis d'avoir un apercu du phenomene global. Une deuxieme serie d'essais fut realisee numeriquement a l'Universite de Moncton avec l'outil OpenFOAM pour des conditions d'ecoulement laminaire et bidimensionnel. Cette etude a donc comme but de poursuivre l'enquete de l'aerodynamique oscillatoire des jets impactant des parois courbes, mais pour un regime d'ecoulement transitoire, turbulent, tridimensionnel. Les nombres de Reynolds utilises dans l'etude numerique, bases sur le diametre du jet lineaire observe, sont de Red = 3333 et 6667, consideres comme etant en transition vers la turbulence. Dans cette etude, un montage numerique est construit. Le maillage, le schema numerique, les conditions frontiere et la discretisation sont discutes et choisis. Les resultats sont ensuite valides avec des donnees turbulentes experimentales. En modelisation numerique de turbulence, les modeles de Moyennage Reynolds des Equations Naviers Stokes (RANS) presentent des difficultes avec des ecoulements instationnaires en regime transitionnel. La Simulation des Grandes Echelles (LES) presente une solution plus precise, mais au cout encore hors de portee pour cette etude. La methode employee pour cette etude est la Simulation des Tourbillons Detaches (DES), qui est un hybride des deux methodes (RANS et LES). Pour analyser la topologie de l'ecoulement, la decomposition des modes propres (POD) a ete egalement ete effectuee sur les resultats numeriques. L'etude a demontre d'abord le temps de calcul relativement eleve associe a des essais DES pour garder le nombre de Courant faible. Les resultats numeriques ont cependant reussi a reproduire correctement le basculement asynchrone observe dans les essais experimentaux. Le basculement observe semble etre cause par des effets transitionnels, ce qui expliquerait la difficulte des modeles RANS a correctement reproduire l'aerodynamique de l'ecoulement. L'ecoulement du jet, a son tour, est pour la plupart du temps tridimensionnel et turbulent sauf pour de courtes periodes de temps stable et independant de la troisieme dimension. L'etude topologique de l'ecoulement a egalement permit la reconaissances de structures principales sousjacentes qui etaient brouillees par la turbulence. Mots cles : jet impactant, paroi concave, turbulence, transitionnel, simulation des tourbillons detaches (DES), OpenFOAM.

A simple and specific high performance liquid chromatography method for the assay of a series of novel dermal penetration enhancers.

PubMed

Michniak, B B; Seyda, K L

1993-02-01

Synopsis A series of clofibric acid amides has been synthesized and previously reported by the authors as possessing enhancer activity in vitro in athymic nude mouse skin against model drugs, hydrocortisone-21-acetate and beta-methasone-17-valerate. An assay was required for each of these enhancers however, which would be specific for each compound and would also separate model drugs and their metabolite peaks. This study reports reverse phase high performance liquid chromatography assays for clofibric acid amide and seven derivatives (Ia-Ig). All enhancers showed maximum absorption at 232 nm, betamethasone (BM) and its valerate (BMV) at 238 nm, and hydrocortisone (HC) and its acetate (HCA) at 242 nm. Practical units of detection for the amides were 0.46-2.8 mug ml(-1) and peaks were sharp and well-separated from steroid peaks in three vehicles - methanol alone. Franz diffusion cell receptor phase samples (isotonic phosphate buffer), and full-thickness athymic nude mouse skin extracts in methanol. Mobile phases consisted of various proportions of acetonitrile and water, some with 2-propanol. The octyl amide for example, with mobile phase CH(3)CN: H(2)O (85:15) at 1 ml min(-1) had a retention time (t(R)) of 7.9 mins. Under the same conditions, retention times for the steroids were HC, t(R)= 3.3 mins; HCA, t(R)= 4.3 mins; BM, t(R)= 3.4 mins; BMV, t(R)= 4.6 mins. Résumé Les auteurs avaient démontré dans un article précédent le pouvoir accélérateur de pénétration dermique in vitro d'une gamme d'amides d'acide clofibrique sur la peau de souris sans poils, et sans thymus avec des médicaments types tels que l'acetate 21 d'hydrocortisone et le valerate 17 de beta-metasone. Il a cependant été requis, pour chacun de ces accélérateurs, un test spécifique pour chaque composition, permettant de séparer chaque médicament et les pics des métabolites. Cette étude décrit des tests par chromatographie liquide à haute performance en phase inverse pour l'acide chlofibrique et 7 dérivés (Ia-Ig). Tous les accélérateurs ont montré une absorption maximale à 232 nm, la beta-metasone (BM) et son valerate (BMV) à 238 nm, l'hydrocortisone (HC) et son acetate (HCA) à 242 nm. Les unités de détection s'élevaient à 0.46-2.8 mug ml(-1) pour les amides et les pics étaient aigus et distincts des pics stéroïdes et se composaient de 3 véhicules - le méthanol seul, des échantillons du récepteur de cellule de diffusion Franz (tampon du phosphate isotonique) et des extraits de peau de souris sans thymus dans du méthanol. Les phases mobiles étaient constituées de différentes proportions d'acetonitrile et d'eau, certaines avec du propanol-2. L'amide octyl par exemple, avec une phase mobile CH(3)CN: H(2)O (85:15) à 1 ml min(-1) avait un temps de rétention (t(R)) de 7.9 min. Dans des conditions identiques, les temps de rétention pour les stéroïdes étaient les suivants: pour HC, t(R)= 3.3 mins; pour HCA, t(R)= 4.3 mins; pour BM: t(R)= 3.4 mins; pour BMV: t(R)= 4.6 mins.

AGARD/SMP Review Damage Tolerance for Engine Structures. 3. Component Behaviour and Life Management

DTIC Science & Technology

1990-06-01

Life Management (Revue AGARD/SMP - ToIrance aux Dommages pour les Composants de Moteurs 3. Le Comportement des Composants et la Gestion %𔄀 de Leur Dur...Structures 3. Component Behaviour and Life Management . (Revue AGARD/SMP - ToI~rance aux Dommages pour les Compos ants de Moteurs 3. Le Comportement...engine parts. The present report includes the papers presented during Workshop Ill which was devoted to Component Behaviour and Life Management . It also

Trust Repair between a Military Organization and a Local Population: A Pilot Study

DTIC Science & Technology

2011-02-01

l’aspect « public » du paradigme IIMP, une approche relativement nouvelle pour un grand nombre de militaires et le plus grand des défis pour les...questionnaires were reviewed and approved by the DRDC Human Research Ethics Committee (HREC) and all participants received remuneration according to DRDC...Form. The Human Research Ethics Committee (HREC) of Defence Research and Development Canada (DRDC) has approved this study (L-701A). If you have

Cost Effective and Affordable Guidance and Control Systems.

DTIC Science & Technology

1985-02-01

aider A is mpdcification. En bref La ligns I spdcifie l’erreur do position absolue (coordonnles terrestres ) A long terme souheitde pour le syst~me do...suffit de" passer aur des rspbres terrestres convenus li 1’svance). Vest Ia raison pour laquolle cette solution est habituellement retenue. Elie...guidage, mime largu~es de fagon trbs prdcise par les calculateurs des avions modernes sur des objectifs terrestres fixes. La confiance misc depuis dans le

Leadership and Diversity in the Canadian Forces: A Conceptual Model and Research Agenda

DTIC Science & Technology

2006-09-01

refers both to the four designated groups identified in Employment Equity (EE) legislation (i.e., women, visible minorities, Aboriginals, and...policies/programs and answers directly to the Deputy Minister and the Chief of Defence Staff. There are also advisory groups for each designated ...pour promouvoir l’équilibre entre la vie personnelle et professionnelle. Les FC tirent de l’arrière comparativement aux entreprises privées pour ce qui

Diffraction grating-based sensing optofluidic device for measuring the refractive index of liquids.

PubMed

Calixto, Sergio; Bruce, Neil C; Rosete-Aguilar, Martha

2016-01-11

We describe a simple and versatile optical sensing device for measuring refractive index of liquids. The sensor consists of a sinusoidal relief grating in a glass cell. Device calibration is done by pouring in the cell different liquids of known refractive indices. Each time a liquid is poured first order intensity is measured. The fabrication process and testing of the prototype device is described. An application in the measurement of temperature is also presented.

Control of experimental Triatoma infestans populations: effect of pour-on cypermethrin applied to chickens under natural conditions in the Argentinean Chaco region.

PubMed

Amelotti, I; Catalá, S S; Gorla, D E

2014-06-01

Among peridomestic structures, chicken coops are sites of major importance for the domestic ecology of Triatoma infestans (Hemiptera: Reduviidae). The aim of this study was to evaluate in an experimental context the effects of a cypermethrin pour-on formulation applied to chickens on blood intake, moulting and mortality in T. infestans, under the natural climatic conditions of a region endemic for Chagas' disease. Experimental chicken huts were made of bricks and covered with plastic mosquito nets. Ninety fourth-instar nymphs were maintained in each hut. The study used a completely random design in which chickens in the experimental group were treated with a cypermethrin pour-on formulation. Five replicates (= huts) of the experimental and control groups were conducted. The number of live T. infestans, blood intake and moults to fifth-instar stage were recorded at 1, 5, 20, 35 and 45 days after the application of cypermethrin. Cumulative mortality was higher in nymphs exposed to treated chickens (> 71%) than in control nymphs (< 50%) (P < 0.01). Blood intake and moulting rate were lower in nymphs fed on treated chickens than in control nymphs (P < 0.05). Pour-on cypermethrin was able to cause significant mortality, although it did not eliminate the experimental population of T. infestans. © 2013 The Royal Entomological Society.

ROAD MAP FOR DEVELOPMENT OF CRYSTAL-TOLERANT HIGH LEVEL WASTE GLASSES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K.; Peeler, D.; Herman, C.

The U.S. Department of Energy (DOE) is building a Tank Waste Treatment and Immobilization Plant (WTP) at the Hanford Site in Washington to remediate 55 million gallons of radioactive waste that is being temporarily stored in 177 underground tanks. Efforts are being made to increase the loading of Hanford tank wastes in glass while meeting melter lifetime expectancies and process, regulatory, and product quality requirements. This road map guides the research and development for formulation and processing of crystaltolerant glasses, identifying near- and long-term activities that need to be completed over the period from 2014 to 2019. The primary objectivemore » is to maximize waste loading for Hanford waste glasses without jeopardizing melter operation by crystal accumulation in the melter or melter discharge riser. The potential applicability to the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF) will also be addressed in this road map. The planned research described in this road map is motivated by the potential for substantial economic benefits (significant reductions in glass volumes) that will be realized if the current constraints (T1% for WTP and TL for DWPF) are approached in an appropriate and technically defensible manner for defense waste and current melter designs. The basis of this alternative approach is an empirical model predicting the crystal accumulation in the WTP glass discharge riser and melter bottom as a function of glass composition, time, and temperature. When coupled with an associated operating limit (e.g., the maximum tolerable thickness of an accumulated layer of crystals), this model could then be integrated into the process control algorithms to formulate crystal-tolerant high-level waste (HLW) glasses targeting high waste loadings while still meeting process related limits and melter lifetime expectancies. The modeling effort will be an iterative process, where model form and a broader range of conditions, e.g., glass composition and temperature, will evolve as additional data on crystal accumulation are gathered. Model validation steps will be included to guide the development process and ensure the value of the effort (i.e., increased waste loading and waste throughput). A summary of the stages of the road map for developing the crystal-tolerant glass approach, their estimated durations, and deliverables is provided.« less

IMPACT OF NOBLE METALS AND MERCURY ON HYDROGEN GENERATION DURING HIGH LEVEL WASTE PRETREATMENT AT THE SAVANNAH RIVER SITE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M; Tommy Edwards, T; David Koopman, D

2009-03-03

The Defense Waste Processing Facility (DWPF) at the Savannah River Site vitrifies radioactive High Level Waste (HLW) for repository internment. The process consists of three major steps: waste pretreatment, vitrification, and canister decontamination/sealing. HLW consists of insoluble metal hydroxides (primarily iron, aluminum, calcium, magnesium, manganese, and uranium) and soluble sodium salts (carbonate, hydroxide, nitrite, nitrate, and sulfate). The pretreatment process in the Chemical Processing Cell (CPC) consists of two process tanks, the Sludge Receipt and Adjustment Tank (SRAT) and the Slurry Mix Evaporator (SME) as well as a melter feed tank. During SRAT processing, nitric and formic acids are addedmore » to the sludge to lower pH, destroy nitrite and carbonate ions, and reduce mercury and manganese. During the SME cycle, glass formers are added, and the batch is concentrated to the final solids target prior to vitrification. During these processes, hydrogen can be produced by catalytic decomposition of excess formic acid. The waste contains silver, palladium, rhodium, ruthenium, and mercury, but silver and palladium have been shown to be insignificant factors in catalytic hydrogen generation during the DWPF process. A full factorial experimental design was developed to ensure that the existence of statistically significant two-way interactions could be determined without confounding of the main effects with the two-way interaction effects. Rh ranged from 0.0026-0.013% and Ru ranged from 0.010-0.050% in the dried sludge solids, while initial Hg ranged from 0.5-2.5 wt%, as shown in Table 1. The nominal matrix design consisted of twelve SRAT cycles. Testing included: a three factor (Rh, Ru, and Hg) study at two levels per factor (eight runs), three duplicate midpoint runs, and one additional replicate run to assess reproducibility away from the midpoint. Midpoint testing was used to identify potential quadratic effects from the three factors. A single sludge simulant was used for all tests and was spiked with the required amount of noble metals immediately prior to performing the test. Acid addition was kept effectively constant except to compensate for variations in the starting mercury concentration. SME cycles were also performed during six of the tests.« less

Mesure et retroaction sur un qubit multi-niveaux en electrodynamique quantique en circuit non lineair

NASA Astrophysics Data System (ADS)

Boissonneault, Maxime

L'electrodynamique quantique en circuit est une architecture prometteuse pour le calcul quantique ainsi que pour etudier l'optique quantique. Dans cette architecture, on couple un ou plusieurs qubits supraconducteurs jouant le role d'atomes a un ou plusieurs resonateurs jouant le role de cavites optiques. Dans cette these, j'etudie l'interaction entre un seul qubit supraconducteur et un seul resonateur, en permettant cependant au qubit d'avoir plus de deux niveaux et au resonateur d'avoir une non-linearite Kerr. Je m'interesse particulierement a la lecture de l'etat du qubit et a son amelioration, a la retroaction du processus de mesure sur le qubit de meme qu'a l'etude des proprietes quantiques du resonateur a l'aide du qubit. J'utilise pour ce faire un modele analytique reduit que je developpe a partir de la description complete du systeme en utilisant principalement des transfprmations unitaires et une elimination adiabatique. J'utilise aussi une librairie de calcul numerique maison permettant de simuler efficacement l'evolution du systeme complet. Je compare les predictions du modele analytique reduit et les resultats de simulations numeriques a des resultats experimentaux obtenus par l'equipe de quantronique du CEASaclay. Ces resultats sont ceux d'une spectroscopie d'un qubit supraconducteur couple a un resonateur non lineaire excite. Dans un regime de faible puissance de spectroscopie le modele reduit predit correctement la position et la largeur de la raie. La position de la raie subit les decalages de Lamb et de Stark, et sa largeur est dominee par un dephasage induit par le processus de mesure. Je montre que, pour les parametres typiques de l'electrodynamique quantique en circuit, un accord quantitatif requiert un modele en reponse non lineaire du champ intra-resonateur, tel que celui developpe. Dans un regime de forte puissance de spectroscopie, des bandes laterales apparaissent et sont causees par les fluctuations quantiques du champ electromagnetique intra-resonateur autour de sa valeur d'equilibre. Ces fluctuations sont causees par la compression du champ electromagnetique due a la non-linearite du resonateur, et l'observation de leur effet via la spectroscopie d'un qubit constitue une premiere. Suite aux succes quantitatifs du modele reduit, je montre que deux regimes de parametres ameliorent marginalement la mesure dispersive d'un qubit avec un resonateur lineaire, et significativement une mesure par bifurcation avec un resonateur non lineaire. J'explique le fonctionnement d'une mesure de qubit dans un resonateur lineaire developpee par une equipe experimentale de l'Universite de Yale. Cette mesure, qui utilise les non-linearites induites par le qubit, a une haute fidelite, mais utilise une tres haute puissance et est destructrice. Dans tous ces cas, la structure multi-niveaux du qubit s'avere cruciale pour la mesure. En suggerant des facons d'ameliorer la mesure de qubits supraconducteurs, et en decrivant quantitativement la physique d'un systeme a plusieurs niveaux couple a un resonateur non lineaire excite, les resultats presentes dans cette these sont pertinents autant pour l'utilisation de l'architecture d'electrodynamique quantique en circuit pour l'informatique quantique que pour l'optique quantique. Mots-cles: electrodynamique quantique en circuit, informatique quantique, mesure, qubit supraconducteur, transmon, non-linearite Kerr

Etude de l'impact de la valorisation energetique de pneus hors d'usage, dans une cimenterie, sur les emissions gazeuses par modelisation de la dispersion atmospherique

NASA Astrophysics Data System (ADS)

Bredin, Nathalie

La génération incéssante de déchets nécessite le développement de nouvelles technologies, telle que la valorisation énergétique, pour en disposer. Une filière appropriée pour valoriser énergétiquement les déchets est le procédé cimentier. L'industrie du ciment est une des grandes consommatrices d'énergie. La température nécessaire à la préparation du ciment se situe aux environs de 1450°C pour faire réagir la matière première (cru) qui est sous forme poudreuse et constituée principalement de roches calcaires, argileuses, schisteuses,... Les gaz de combustion ont un long temps de résidence dans les fours. De plus, le mode de fonctionnement des fours est responsable d'un effet de lessivage des gaz acides par le cru alcalin. Ces propriétés font du procédé cimentier un bon candidat pour la valorisation énergétique des déchets. Les déchets interessants pour les cimenteries sont, entre autres, les huiles usées, les solvants usés et les pneus usés qui ont un pouvoir calorifique équivalent à celui du charbon. Les rejets à l'atmosphère des cimenteries sont principalement des émissions gazeuses. Ainsi, l'impact de la valorisation de pneus usés sur les émissions gazeuses de la cimenterie Saint-Laurent de Joliette a été étudié, à l'aide de l'outil qu'est la modélisation de la dispersion atmosphérique. Le modèle utilisé ISC-ST2, Industrial Source Complex-Short Term, est de type gaussien. L'analyse des concentrations maximales horaires et moyennes sur différentes périodes de temps (1 heure, 8 heures, ..., 1 an) des émissions gazeuses dans l'air ambiant montre que celles-ci sont en deçà des normes émises par le gouvernement québécois et par la Communauté Urbaine de Montréal. L'étude de la distribution géographique des polluants, d'après les concentrations annuelles, dans un rayon de 5 km autour de la cimenterie montre que le fait d'utiliser des pneus comme combustible de substitution n'a qu'un faible impact sur la concentration des contaminants au niveau du sol. L'étude du modèle gaussien de dispersion a permis de mettre au point un nouvel outil: la corrélation existant entre les concentrations latérales et verticales des polluants dans le panache. Cet outil utilisé pour étudier les schémas de dispersion atmosphérique de Turner en milieu rural, et de Briggs en milieux urbain et rural, montre que, en milieu rural, le schéma de dispersion proposé par Briggs présente une dispersion plus importante que celui de Turner pour les classes neutres et instables et moins importantes pour les classes stables. La comparaison des schémas de Briggs (rural et urbain) confirme que la dispersion en milieu urbain est plus importante qu'en milieu rural.

Revetements bioactifs a base de chondroitine sulfate et de facteurs de croissance pour applications vasculaires

NASA Astrophysics Data System (ADS)

Lequoy, Pauline

Malgre des avancees technologiques indeniables, l'efficacite des implants biomedicaux est encore limitee par les biomateriaux synthetiques qui les composent, notamment en raison de leur incapacite a generer une reponse biologique adequate. En particulier, la guerison tissulaire autour des implants vasculaires reste problematique. Une etude de la litterature a montre que dans le cas des endoprotheses couvertes (tuyaux polymeriques utilises pour la reparation endovasculaire des anevrismes de l'aorte abdominale), le manque de guerison observe s'explique non seulement par l'inertie des biomateriaux utilises mais aussi par le fait que l'implant est insere dans un vaisseau malade favorisant la mort des cellules par apoptose et presentant une depletion cellulaire marquee. L'hypothese a la base de ce projet est qu'un revetement bioactif pourrait ameliorer la guerison et la colonisation de l'implant par les cellules vasculaires et ainsi favoriser l'attachement de l'implant dans le vaisseau malade afin de prevenir les complications a long terme. Dans ce contexte, deux molecules anti-apoptotiques ont ete selectionnees pour developper le revetement, la chondroitine sulfate (CS), un glycosaminoglycane de la matrice extracellulaire, et le facteur de croissance de l'epiderme (EGF) qui possede egalement un role important dans la guerison tissulaire. L'un des defis de ce projet est de preserver la bioactivite de ces molecules lors de leur immobilisation dans un revetement. Pour etablir une preuve de concept, nous avons demontre qu'un revetement CS+EGF obtenu par greffage covalent permet d'ameliorer significativement la survie des cellules vasculaires humaines (cellules musculaires lisses, CMLV, et fibroblastes) sur les materiaux realistes (PET, ePTFE). Apres avoir transfere ce revetement sur des implants commerciaux en ePTFE, des tests in vivo ont demontre une amelioration de la guerison grâce au revetement bioactif, cependant la guerison n'a pas ete totale dans la cavite anevrismale. Pour ameliorer la bioactivite du revetement, un systeme de capture oriente base sur la complementarite de deux peptides (superhelices 'coiled-coil') a ete utilise pour immobiliser l'EGF sur CS. Cette immobilisation orientee a permis une meilleure efficacite de capture, ainsi qu'une augmentation marquee de la survie des CMLV par rapport au greffage covalent aleatoire utilise precedemment. De plus, les travaux realises ont permis l'avancement de la comprehension des proprietes antiadhesives selectives de CS par comparaison avec le dextrane carboxymethyle. Enfin, nous avons demontre que la polyvalence du systeme de capture oriente pour facteurs de croissance permet la co-immobilisation de deux facteurs de croissance, EGF et VEGF (facteur de croissance de l'endothelium vasculaire), et ce a des ratios variables. Les densites surfaciques ont ete optimisees par simple changement de concentration lors de l'incubation. Des etudes cellulaires avec une gamme de ratios EGF/VEGF ont revele un effet synergique des deux facteurs de croissance sur la survie des CMLV et des cellules endotheliales. Les travaux menes ont permis de developper des revetements bioactifs anti-apoptotiques qui ameliorent la survie des cellules vasculaires et constituent une avancee vers la creation d'endoprotheses bioactives. Il apparait egalement que la plateforme d'immobilisation coiled-coil presente un grand potentiel pour la construction de surfaces bioactives complexes et la comprehension du role de differents facteurs de croissance dans les comportements cellulaires.

Qualité des eaux de la station de traitement de la ville de Skikda, Algérie Essais d'optimisation de la clarification

NASA Astrophysics Data System (ADS)

Meghzili, B.; Medjram, M. S.; Achour, S.

2005-05-01

A cause de la sécheresse qui a sévit durant une décennie, la station de traitement de l'eau potable de la ville de Skikda Algérie, en vue de combler le déficit en eau, utilise un mélange des eaux de surface (barrage) et des eaux souterraines (forage). Les résultats des analyses physico-chimiques de ces eaux montrent la présence de micropolluants, notamment le mercure, avec une concentration de 0.035 mg/l pour les eaux de surface et une concentration de 0.02 mg/l pour les eaux souterraines. Ces résultats obtenus, montrent également que la concentration en matières organiques dépasse, pour les deux sources, les normes OMS. Afin de réduire les effets de cette pollution, nous avons calculé les doses nécessaires des différents réactifs utilisés sur la base des essais d'optimisation réalisés en laboratoire. Les résultats obtenus nous ont permis de conclure que les doses de 30 à 60 mg/l de sulfate d'aluminium (S.A) sont nécessaires à une bonne élimination de la turbidité et des matières organiques (M.O) et que l'utilisation du charbon active en poudre (C.A.P) permet la réduction de la teneur en mercure au dessous du seuil admissible. L'utilisation d'un adjuvant (chaux vive) permet d'améliorer les résultats surtout pour la turbidité (4 mg/l). Une préchloration au break point semble intéressante pour améliorer la phase de floculation.

La prise en charge à long terme de l’asthme chez les enfants inuits et des Premières nations : un outil de transfert du savoir fondé sur les lignes directrices canadiennes pour l’asthme pédiatrique, conçu pour être utilisé par les professionnels de la santé de première ligne qui travaillent dans des communautés isolées

PubMed Central

Kovesi, Tom; Giles, Brenda Louise; Pasterkamp, Hans

L’asthme est un grave problème de santé pour les enfants inuits et des Premières nations. Chez les enfants de moins d’un an, il faut distinguer l’asthme de la bronchiolite virale, anormalement fréquente chez les enfants autochtones du Canada. Chez les enfants de moins de six ans, le diagnostic dépend de la présence de symptômes classiques, de l’absence de caractéristiques atypiques et de la consignation de la réponse au traitement, notamment la réponse rapide et transitoire aux bronchodilatateurs. Chez les enfants plus âgés, il faut, dans la mesure du possible, déterminer la présence d’une obstruction réversible des voies aériennes par spirométrie afin de confirmer le diagnostic, ainsi qu’évaluer et corriger les déclencheurs environnementaux. L’utilisation régulière de corticoïdes en aérosol est la principale mesure à prendre pour maintenir un bon contrôle de l’asthme chez les enfants asthmatiques. Les clients et leur famille devraient recevoir une formation sur l’asthme. Il faut réévaluer régulièrement le contrôle aux visites de suivi dans des centres de santé et rajuster le traitement à la dose la plus basse possible pour le maintien de ce contrôle.

Methodologies nouvelles pour la realisation d'essais dans la soufflerie Price-Paidoussis

NASA Astrophysics Data System (ADS)

Flores Salinas, Manuel

Le present memoire en genie de la production automatisee vise a decrire le travail effectue dans la soufflerie Price-Paidoussis du laboratoire LARCASE pour trouver les methodologies experimentales et les procedures de tests, qui seront utilisees avec les modeles d'ailes actuellement au laboratoire. Les methodologies et procedures presentees ici vont permettre de preparer les tests en soufflerie du projet MDO-505 Architectures et technologies deformables pour l'amelioration des performances des ailes, qui se derouleront durant l'annee 2015. D'abord, un bref historique des souffleries subsoniques sera fait. Les differentes sections de la soufflerie Price-Paidoussis seront decrites en mettant l'emphase sur leur influence dans la qualite de l'ecoulement qui se retrouve dans la chambre d'essai. Ensuite, une introduction a la pression, a sa mesure lors de tests en soufflerie et les instruments utilises pour les tests en soufflerie au laboratoire LARCASE sera presente, en particulier le capteur piezoelectrique XCQ-062. Une attention particuliere sera portee au mode de fonctionnement, a son installation, a la mesure et a la detection des frequences et aux sources d'erreurs lorsqu'on utilise des capteurs de haute precision comme la serie XCQ-062 du fournisseur Kulite. Finalement, les procedures et les methodologies elaborees pour les tests dans la soufflerie Price-Paidoussis seront utilisees sur quatre types d'ailes differentes. L'article New methodology for wind tunnel calibration using neural networks - EGD approch portant sur une nouvelle facon de predire les caracteristiques de l'ecoulement a l'interieur de la soufflerie Price-Paidoussis se trouve dans l'annexe 2 de ce document. Cet article porte sur la creation d'un reseau de neurones multicouche et sur l'entrainement des neurones, Ensuite, une comparaison des resultats du reseau de neurones a ete fait avec des valeurs simules avec le logiciel Fluent.

Effets de la pollution de l’air sur la santé

PubMed Central

Abelsohn, Alan; Stieb, Dave M.

2011-01-01

Résumé Objectif Faire connaître aux médecins de famille les effets de la pollution atmosphérique sur la santé et indiquer quels conseils donner aux patients vulnérables pour qu’ils soient moins exposés. Sources de l’information On a consulté MEDLINE à l’aide des termes relatifs à la pollution atmosphérique et à ses effets indésirables. On a révisé les articles en anglais publiés entre janvier 2008 et décembre 2009. La plupart des études contenaient des preuves de niveau II. Principal message Au Canada, la pollution de l’air extérieur cause une morbidité et une mortalité importantes. Elle peut affecter le système respiratoire (exacerbation de l’asthme et de la maladie pulmonaire obstructive chronique) et le système cardiovasculaire (déclencher l’arythmie, l’insuffisance cardiaque et les AVC). La cote air santé (CAS) est un nouvel outil de communication mis au point par Santé Canada et Environnement Canada qui indique sur une échelle de 1 à 10, le risque pour la santé causé par la pollution atmosphérique. La CAS est largement diffusée dans les médias et cet outil pourrait être utile au médecin de famille pour inciter les patients à haut risque (comme ceux qui souffrent d’asthme, de maladie pulmonaire obstructive chronique ou d’insuffisance cardiaque) à réduire leur exposition à la pollution atmosphérique. Conclusion Le médecin de famille peut se servir de la CAS et de ses messages sur la santé pour enseigner aux asthmatiques et aux autres patients à risque élevé la façon de réduire les risques pour la santé causés par la pollution atmosphérique.

Evaluation of Sealing Materials and Techniques for Installing Quoin and Miter Block Backing Grout

DTIC Science & Technology

2015-11-01

being used effectively in the field. The materials currently in use have low viscosities and are typically poured behind the quoin and miter blocks in...tively in the field. The materials now used have low viscosities . They are typ- ically poured behind the quoin and miter blocks in lifts. The perimeter of...colder temperatures. Low viscosity at warmer temperatures. Hilti HIT ICE Epoxy Acrylate It is primarily a cold weather product that had poor

Canadian Paramedic Services Standards Report: A Strategic Planning Report

DTIC Science & Technology

2014-06-01

Gestion des programmes 7. Nouvelle technologie 8. Gestion des situations d’urgence La section 4 du rapport sur la stratégie de ...normalisation (CSA) et du Programme canadien pour la sûreté et la sécurité (PCSS). Ce projet a réuni des experts clés de la communauté canadienne du ...existantes pour les services paramédicaux actuels au Canada aux besoins présents et futurs de la communauté

L'optique pour la sécurité sanitaire des aliments

NASA Astrophysics Data System (ADS)

Piat, Félix

2017-12-01

Il semble aujourd'hui évident que chaque produit alimentaire commercialisé ne représente aucun danger pour la santé. Cet acquis repose pourtant sur un système complexe de règles et de contrôles appliqués quotidiennement dans les coulisses de l'industrie agro-alimentaire. Les technologies optiques y jouent un rôle prépondérant, permettant de séparer le bon grain de l'ivraie.

Bistatic Synthetic Aperture Radar, TIF - Report (Phase 1)

DTIC Science & Technology

2004-11-01

Cette recherche permet d’obtenir une compr6hension en profondeur des capacit6s et des difficult6s associ6es aux concepts du ROS bistatique et...Radar (SAR) Bistatic SAR Performance Analysis Defence R&D Canada R & D pour la defense Canada Canada’s Leader in Defence Chef de file au Canada en ...I 1f1 Defence Research and Recherche et developpement Development Canada pour la defense Canada DEFENCE DEFENSE Bistatic Synthetic Aperture Radar TIF

Modelling Broadband Scattering From Shelled Spheres in a Waveguide

DTIC Science & Technology

2007-10-01

profonde. Le contenu spectral de l’echo produit par une cible peut varier de fagon appreciable en fonction de sa profondeur et de sa distance dans le...Canada’s leader in defence and National Security Science and Technology R&D pour la defense Canada Chef de file au Canada en matiere de science et...Copy No. nent Development Canada pour la defense Canada • ^g, M Defence Research and Recherche et deyeloppem r£ m> DEFENCE I « M

Development of a Dynamic Biomechanical Model for Load Carriage: Phase II Part A: Initial Development of a Novel Strap Tension Sensor

DTIC Science & Technology

2005-08-01

substantielle » et pourrait de ce fait être breveté. D’autres avenues (que le brevetage) sont possibles pour la commercialisation du dispositif en...breveté. D’autres avenues (que le brevetage) sont possibles pour la commercialisation du dispositif en protégeant certains de ses aspects au moyen...information: 1. INVENTOR(S) A. University Name Dept. Faculty Phone Susan A. Reid, School of Physical and Health Education

Theoretical and Experimental Methods in Hypersonic Flows (Les Methodes Theoriques et Experimentales pour l’Etude Des Ecoulements Hypersoniques)

DTIC Science & Technology

1993-04-01

PROCEEDINGS 514 OELECTE f Theoretical and A U Experimental Methods in A Hypersonic Flows (Les Methodes Th6oriques et Experimentales pour 1’Etude des...nitrogen ent for both equilibrium and non -equilibrium chemistry between the two groups . Both groups state that the boundary makes this mode even more...flowfield on control is also m?,ndatory unstable due to the necessary oblate shape of Hermes. when the experimental rebuilding is clearly poor and

What Should Users Expect from Information Storage and Retrieval Systems of the 1980’s

DTIC Science & Technology

1981-12-01

cide dcentrer sur ls marchE de l1information secondaire, on doit d~finir Is secteur , rschercher des appuis (coop~rants) pour couvrir cc secteur ...inutiles. Ii appartient bien entendu chaque Gouvernemant dlapprdcier sea prioritds, mais en se plagant dans Is cadre tracE. GOUVERNEMENT ET SECTEUR PRIVE A...directive A76 salon laqualle le Gouvernament f~d~ral slappuiera sur Is secteur priv6 pour publiar at dissminar llinformation scientifique at technique

Choice for All: ICAART 88. Proceedings of the International Conference of the Association for the Advancement of Rehabilitation Technology (Montreal, Canada, June 25-30, 1988). Volume III = Choix pour tous: ICAART 88. Compte rendu conference internationale pour le developpement de la technologie en readaptation (Montreal, Canada, Juin 25-30, 1988).

ERIC Educational Resources Information Center

RESNA: Association for the Advancement of Rehabilitation Technology, Washington, DC.

In these proceedings are compiled 290 papers from 15 countries, demonstrating applications of rehabilitation engineering and technology. The 16 Special Interest Groups of the Association for the Advancement of Rehabilitation Technology (RESNA) present papers in the following interest areas: Service Delivery Practice, Personal Transportation,…

AIMSsim Version 2.3.4 - User Manual

DTIC Science & Technology

2008-01-01

sera en mesure d’utiliser le système efficacement et moyennant une formation minimale, un prototype d’interface humain -machine (IHM) a été développé...d’utiliser l’ensemble de capteurs efficacement et moyennant une formation minimale, un prototype d’interface humain -machine (IHM) a été développé pour...recherche AIMSsim offrent à l’expérimentateur un niveau de simulation assez détaillé pour mener des analyses du rendement humain , qui fournissent à

Frequency Assignment, Sharing and Conservation in Systems (Aerospace). (l’Attribution, le partage et la conservation des frequences pour les systemes aeronautiques et spatiales)

DTIC Science & Technology

1999-01-01

que pour les installations et le personnel mis ä sa disposition. T- l Technical Evaluation Report of the RTO...radiocommunications sur le radar, on peut mettre en oeuvre des techniques de Formation de Faisceau par le Calcul qui permettent d’augmenter encore le niveau...plus 6loign6s pouvant fonctionner sur les mSmes canaux de frequence que le radar sans g£ne mutuelle1. equipements de radiocommunication

Users Guide to BellhopDRDC_V4: Active and Passive Versions

DTIC Science & Technology

2010-10-01

tactique pour la planification et les opérations navales. Le premier est une version acoustique passive appelée BellhopDRDC_ray_TL_v4. Les résultats de...Importance L’Environment Modeling Manager est un système perfectionné dans le domaine de l’océanographie tactique pour le soutien à la planification et aux...Flag for using Thorpe volume attenuation T = use Thorpe attenuation, the preferred choice and default N = use no attenuation ‘S’ = surface loss

Medication for Military Aircrew: Current Use, Issues, and Strategies for Expanded Options (les medicaments pour les equipaes militaires: Consommation actuelle, questions et strategies pour des options elargies)

DTIC Science & Technology

2001-06-01

HMG-CoA reductase inhibitors, commonly referred to as “statins” (lovastatin, pravastatin, simvastatin, fluvastatin, atorvastatin ) d. Others (nicotinic...cholesterol by 2 - 15%. Many statins (pravastatin, atorvastatin , fluvastatin, lovastatin, and simvastatin) have been developed for clinical use and are now...trail making test, or visual memory test.16 There are unpublished data about atorvastatin and pravastatin, in which both showed an increase in

Car Talk: Ethnic And Religious Identity In The Central African Republic

DTIC Science & Technology

2017-12-01

Republic and Democracy (APRD) began conducting raids on army positions. Ange-Felix Patassé controlled the APRD from his exile in Togo and the group was...Séléka forces razed villages to the ground. As it became apparent Djotodia could not or would not control the Séléka even more groups took up the Séléka...largest groups , the Rassemblement Patriotique pour le Renouveau de la Centrafrique (RPRC), the Front Populaire pour la Reniasance de la Centrafrique

Aerodynamics of Power Plant Installation

DTIC Science & Technology

1981-09-01

eat multiplide par 10 environ loroque l’incidence passe do 0 &i 40*. 11 on eat de mime de la valour maximale, alors que leo minima dvoluent trbs...lentement. Comme pour 1’efficacitd moyenne (fig. 6), leo niveaux de distorsions obtn-nuo au point fixe ont dtd placds our coo courbes. on constate quo pour...do 35’ et 22’ obtenues en comparant lea efficacitds globales. 3.4- Hutaiude .i!4>Lon La figure 10 donine leo valeure dezi fluctuations do proosion

Fully Fueled TACOM Vehicle Storage Test Program.

DTIC Science & Technology

1981-12-01

Messrs. H. Hobart, T. Wilson, and T. Hinkley , DRSTA-GSP, U.S. Army Tank Automotive Command (TACOM) for providing both liai- son and fuel-sampling...and its characteristics are as follows: Density, g/ml 0.9 Flash point , *F 140 Fire point , *F 145 Pour point , *F -50 Neutralization No., TAN 25 TBN 130...following characteristics: Density, g/ml 1.05 Flash point , *F 144 Pour point , *F -27.5 Viscosity, cSt, @ 70*F 29 Boron content 7.4% Water (free

Technique distribuee de gestion de la charge sur le reseau electrique et ring-tree: Un nouveau systeme de communication P2P

NASA Astrophysics Data System (ADS)

Ayoub, Simon

Le reseau de distribution et de transport de l'electricite se modernise dans plusieurs pays dont le Canada. La nouvelle generation de ce reseau que l'on appelle smart grid, permet entre autre l'automatisation de la production, de la distribution et de la gestion de la charge chez les clients. D'un autre cote, des appareils domestiques intelligents munis d'une interface de communication pour des applications du smart grid commencent a apparaitre sur le marche. Ces appareils intelligents pourraient creer une communaute virtuelle pour optimiser leurs consommations d'une facon distribuee. La gestion distribuee de ces charges intelligentes necessite la communication entre un grand nombre d'equipements electriques. Ceci represente un defi important a relever surtout si on ne veut pas augmenter le cout de l'infrastructure et de la maintenance. Lors de cette these deux systemes distincts ont ete concus : un systeme de communication peer-to-peer, appele Ring-Tree, permettant la communication entre un nombre important de noeuds (jusqu'a de l'ordre de grandeur du million) tel que des appareils electriques communicants et une technique distribuee de gestion de la charge sur le reseau electrique. Le systeme de communication Ring-Tree inclut une nouvelle topologie reseau qui n'a jamais ete definie ou exploitee auparavant. Il inclut egalement des algorithmes pour la creation, l'exploitation et la maintenance de ce reseau. Il est suffisamment simple pour etre mis en oeuvre sur des controleurs associes aux dispositifs tels que des chauffe-eaux, chauffage a accumulation, bornes de recharges electriques, etc. Il n'utilise pas un serveur centralise (ou tres peu, seulement lorsqu'un noeud veut rejoindre le reseau). Il offre une solution distribuee qui peut etre mise en oeuvre sans deploiement d'une infrastructure autre que les controleurs sur les dispositifs vises. Finalement, un temps de reponse de quelques secondes pour atteindre 1'ensemble du reseau peut etre obtenu, ce qui est suffisant pour les besoins des applications visees. Les protocoles de communication s'appuient sur un protocole de transport qui peut etre un de ceux utilises sur l'Internet comme TCP ou UDP. Pour valider le fonctionnement de de la technique de controle distribuee et le systeme de communiction Ring-Tree, un simulateur a ete developpe; un modele de chauffe-eau, comme exemple de charge, a ete integre au simulateur. La simulation d'une communaute de chauffe-eaux intelligents a montre que la technique de gestion de la charge combinee avec du stockage d'energie sous forme thermique permet d'obtenir, sans affecter le confort de l'utilisateur, des profils de consommation varies dont un profil de consommation uniforme qui represente un facteur de charge de 100%. Mots-cles : Algorithme Distribue, Demand Response, Gestion de la Charge Electrique, M2M (Machine-to-Machine), P2P (Peer-to-Peer), Reseau Electrique Intelligent, Ring-Tree, Smart Grid

Mechanical and Physical Properties of Recombinant Spider Silk Films Using Organic and Aqueous Solvents

PubMed Central

2015-01-01

Spider silk has exceptional mechanical and biocompatibility properties. The goal of this study was optimization of the mechanical properties of synthetic spider silk thin films made from synthetic forms of MaSp1 and MaSp2, which compose the dragline silk of Nephila clavipes. We increased the mechanical stress of MaSp1 and 2 films solubilized in both HFIP and water by adding glutaraldehyde and then stretching them in an alcohol based stretch bath. This resulted in stresses as high as 206 MPa and elongations up to 35%, which is 4× higher than the as-poured controls. Films were analyzed using NMR, XRD, and Raman, which showed that the secondary structure after solubilization and film formation in as-poured films is mainly a helical conformation. After the post-pour stretch in a methanol/water bath, the MaSp proteins in both the HFIP and water-based films formed aligned β-sheets similar to those in spider silk fibers. PMID:25030809

Self-disinfecting Alginate vs Conventional Alginate: Effect on Surface Hardness of Gypsum Cast-An in vitro Study.

PubMed

Madhavan, Ranjith; George, Navia; Thummala, Niharika R; Ravi, S V; Nagpal, Ajay

2017-11-01

For the construction of any dental prosthesis, accurate impressions are necessary. Hence, we undertook the present study to evaluate and compare the surface hardness of gypsum casts poured from impressions made using conventional alginate and self-disinfecting alginate. A total of 30 impressions of stainless steel die were made, out of which 15 impressions were made with conventional alginate and 15 were made with self-disinfecting alginate and poured using Type III dental stone. Thirty stone specimens were subjected for hardness testing. Data were analyzed using independent samples t-test to compare the mean surface hardness. Difference in surface hardness was statistically insignificant (p > 0.05). Surface hardness of gypsum casts poured using impressions made from self-disinfecting alginate and conventional alginates were comparable. Self-disinfecting alginates may be employed in clinical practice as safe and effective materials to overcome the infection control issues without compromising on the properties of the material.

Fukushima Daiichi Unit 1 Ex-Vessel Prediction: Core-Concrete Interaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robb, Kevin R.; Farmer, Mitchell T.; Francis, Matthew W.

Lower head failure and corium-concrete interaction were predicted to occur at Fukushima Daiichi Unit 1 (1F1) by several different system-level code analyses, including MELCOR v2.1 and MAAP5. Although these codes capture a wide range of accident phenomena, they do not contain detailed models for ex-vessel core melt behavior. However, specialized codes exist for the analysis of ex-vessel melt spreading (e.g., MELTSPREAD) and long-term debris coolability (e.g., CORQUENCH). On this basis, in this paper an analysis was carried out to further evaluate ex-vessel behavior for 1F1 using MELTSPREAD and CORQUENCH. Best-estimate melt pour conditions predicted by MELCOR v2.1 and MAAP5 weremore » used as input. MELTSPREAD was then used to predict the spatially dependent melt conditions and extent of spreading during relocation from the vessel. The results of the MELTSPREAD analysis are reported in a companion paper. This information was used as input for the long-term debris coolability analysis with CORQUENCH. For the MELCOR-based melt pour scenario, CORQUENCH predicted the melt would readily cool within 2.5 h after the pour, and the sumps would experience limited ablation (approximately 18 cm) under water-flooded conditions. Finally, for the MAAP-based melt pour scenarios, CORQUENCH predicted that the melt would cool in approximately 22.5 h, and the sumps would experience approximately 65 cm of concrete ablation under water-flooded conditions.« less

Fukushima Daiichi Unit 1 Ex-Vessel Prediction: Core-Concrete Interaction

DOE PAGES

Robb, Kevin R.; Farmer, Mitchell T.; Francis, Matthew W.

2016-10-31

Lower head failure and corium-concrete interaction were predicted to occur at Fukushima Daiichi Unit 1 (1F1) by several different system-level code analyses, including MELCOR v2.1 and MAAP5. Although these codes capture a wide range of accident phenomena, they do not contain detailed models for ex-vessel core melt behavior. However, specialized codes exist for the analysis of ex-vessel melt spreading (e.g., MELTSPREAD) and long-term debris coolability (e.g., CORQUENCH). On this basis, in this paper an analysis was carried out to further evaluate ex-vessel behavior for 1F1 using MELTSPREAD and CORQUENCH. Best-estimate melt pour conditions predicted by MELCOR v2.1 and MAAP5 weremore » used as input. MELTSPREAD was then used to predict the spatially dependent melt conditions and extent of spreading during relocation from the vessel. The results of the MELTSPREAD analysis are reported in a companion paper. This information was used as input for the long-term debris coolability analysis with CORQUENCH. For the MELCOR-based melt pour scenario, CORQUENCH predicted the melt would readily cool within 2.5 h after the pour, and the sumps would experience limited ablation (approximately 18 cm) under water-flooded conditions. Finally, for the MAAP-based melt pour scenarios, CORQUENCH predicted that the melt would cool in approximately 22.5 h, and the sumps would experience approximately 65 cm of concrete ablation under water-flooded conditions.« less

Sidération myocardique au cours d'une intoxication au monoxyde de carbone (CO) chez une femme enceinte

PubMed Central

Coulibaly, Mahamadoun; Berdai, Mohamed Adnane; Labib, Smael; Harandou, Mustapha

2015-01-01

L'intoxication au monoxyde de carbone (CO) est la première cause de décès par intoxication en France. La littérature est ancienne et peu connue. Les signes les plus fréquents de l'intoxication sont la triade: Céphalées; asthénie, faiblesse musculaire surtout des membres inférieurs. Ses conséquences sont potentiellement graves pour le fœtus quand elle survient chez la femme enceinte, il est particulièrement exposé au risque d'hypoxie en raison de la forte affinité de son hémoglobine pour le CO qui traverse aisément le placenta. Les événements cardiovasculaires ne sont pas rares et peuvent être responsable d'une morbi-mortalité assez importante qui peuvent être d'apparition rapide ou secondaire mais régressent habituellement en quelques jours. Des SCA peuvent survenir lors d'une une intoxication au CO avec à l'extrême infarctus myocardique avec surélévation du segment ST. Il paraît légitime de proposer pour toutes les patientes: l’éloignement maternel de la source de CO; l'oxygénothérapie à 100% au masque facial par les services de secours et pendant le transfert; le traitement par oxygénothérapie hyperbare pour toutes les femmes enceintes, le plus rapidement possible et quelque soit l’âge gestationnel. PMID:26405502

Malformations congénitales à Lubumbashi (République Démocratique du Congo): à propos de 72 cas observés et plaidoyer en faveur du développement d'un Registre National des Malformations Congénitales et d'un Centre National de Référence de Génétique Humaine

PubMed Central

Lubala, Toni Kasole; Shongo, Mick Yapongombo; Munkana, Arthur Ndundula; Mutombo, Augustin Mulangu; Mbuyi, Sébastien Musanzayi; wa Momat, Félix Kitenge

2012-01-01

En République Démocratique du Congo, les malformations congénitales constituent un véritable problème de santé publique. En effet, elles relancent le débat sur les effets de l'intensification de l'activité minière sur la santé de la reproduction. De 2009 à 2010, nous avons calculé une prévalence de 5.84 pour 1000 naissances. Les malformations du système nerveux central étaient les plus fréquentes (2.029 pour 1000) suivies des malformations des membres (1.055 pour 1000), et des fentes oro-faciales (0.811 pour 1000). Ces données sont certainement largement sous-estimées et les causes y relatives en République Démocratique du Congo ne sont ni surveillées, ni prévenues dans le cadre d'une politique gouvernementale. La mise en place d'un registre national et d'un centre national de génétique humaine de référence pourrait constituer un cadre rigoureux, organisé et structuré de surveillance et de prévention des malformations congénitales. PMID:23396951

Magnétochiralité et résonances stochastiques dans les lasers

NASA Astrophysics Data System (ADS)

Bonnet, C.; Bretenaker, F.; Brunel, M.; Chauvat, D.; Emile, O.; Lai, N. D.; Le Floch, A.; Ropars, G.; Ruchon, T.; Singh, K.; Thépot, J.-Y.; Vallet, M.

2002-06-01

Les états propres d'un laser constituent un outil de choix pour étudier les différents rôles joués par le bruit dans un système. D'une part, si on veut isoler un effet petit difficilement accessible par les méthodes classiques, ces états propres permettent de réaliser des mesures différentielles de haute précision, à condition de pouvoir éliminer les bruits mécaniques, optiques, électroniques. A titre d'exemple, nous avons utilisé les états propageant et contrapropageant d'un laser ionique en anneau pour mesurer une interaction fondamentale faible: la biréfringence magnétochirale. Cette "biréfringence" se manifeste en effet par une petite variation d'indice selon le sens de parcours de l'anneau, de l'ordre de Δ n.10^{-11}, indépendante de la polarisation. A l'opposé, les deux états propres d'un laser du type Fabry-Perot constituent un système idéal pour explorer les résonances stochastiques à deux dimensions. Les résonances stochastiques par inhibition et par rotation sont isolées en présence de bruits blancs gaussiens tant pour les bruits optiques que magnétiques. L'utilisation possible de l'émission spontanée comme bruit actif est démontrée.

Investigation experimentale de l'ecoulement et des performances thermiques du nanofluide eau-oxyde de cuivre dans un Micro-Canal Chauffe

NASA Astrophysics Data System (ADS)

Rimbault, Benjamin

Cette these de maitrise presentee par articles visait a etudier le comportement hydraulique et thermique d'un ecoulement de nanofluides en micro-canal chauffe. Nous avons etudie premierement de l'eau distillee, ensuite des melanges de particules d'oxyde de cuivre (taille 29nm) avec de l'eau distillee en concentrations particulaires volumiques 4.5%, 1.03%, et 0.24% (CuO-H2O). L'ecoulement force des differents fluides a ete realise au moyen de pompes a engrenages au sein d'un circuit ferme, comprenant un micro-canal a section rectangulaire (e=1.116mm,1=25.229mm) chauffe sur deux faces paralleles via des cartouches electriques, deux echangeurs de chaleurs en serie, ainsi qu'un debitmetre magnetique. A notre connaissance peu d'etudes sur l'ecoulement de nanofluides d'oxyde de cuivre-eau en micro-canal rectangulaire chauffe sont disponibles dans la litterature, cette recherche sert de contribution. Premierement, une validation avec la litterature a ete effectuee pour le cas d'un ecoulement d'eau entre plaques planes paralleles chauffees. Des essais hydrauliques ont ete realises pour une gamme du nombre de Reynolds allant jusqu'a Re=5000 a temperature constante. Par la suite des essais thermiques jusqu'a Re=2500 ont consiste en une elevation de temperature fixe (20.5°C a 30.5°C) a travers la longueur du micro-canal sous un regime stationnaire. Les resultats ont demontre une augmentation de la perte de pression et du coefficient de frottement des nanofluides sur l'eau pour un meme debit. Une telle augmentation de perte de pression etait de +70%, +25%, et +0 a 30% respectivement pour les concentrations 4.50%, 1.03%, et 0.24%. Concernant la transition laminaire a turbulent les comportements semblaient indiquer une valeur critique semblable entre l'eau et les differentes concentrations avec et sans chauffage a un nombre de Reynolds critique Rem 1000. Nous avons observe une legere augmentation du coefficient de convection thermique avec le debit massique pour les faibles concentrations (1.03% et 0.24%), alors que la concentration 4.5% demontre une nette diminution. En general la performance energetique globale definie par la chaleur transferee sur la puissance de pompage, reste inferieure compare a l'eau pour un meme Reynolds et un meme debit massique egalement. L'eau semble etre la meilleure solution en termes de performance energetique globale.

Methode d'identification parametrique pour la surveillance in situ des joints a recouvrement par propagation d'ondes vibratoires

NASA Astrophysics Data System (ADS)

Francoeur, Dany

Cette these de doctorat s'inscrit dans le cadre de projets CRIAQ (Consortium de recherche et d'innovation en aerospatiale du Quebec) orientes vers le developpement d'approches embarquees pour la detection de defauts dans des structures aeronautiques. L'originalite de cette these repose sur le developpement et la validation d'une nouvelle methode de detection, quantification et localisation d'une entaille dans une structure de joint a recouvrement par la propagation d'ondes vibratoires. La premiere partie expose l'etat des connaissances sur l'identification d'un defaut dans le contexte du Structural Health Monitoring (SHM), ainsi que la modelisation de joint a recouvrements. Le chapitre 3 developpe le modele de propagation d'onde d'un joint a recouvrement endommage par une entaille pour une onde de flexion dans la plage des moyennes frequences (10-50 kHz). A cette fin, un modele de transmission de ligne (TLM) est realise pour representer un joint unidimensionnel (1D). Ce modele 1D est ensuite adapte a un joint bi-dimensionnel (2D) en faisant l'hypothese d'un front d'onde plan incident et perpendiculaire au joint. Une methode d'identification parametrique est ensuite developpee pour permettre a la fois la calibration du modele du joint a recouvrement sain, la detection puis la caracterisation de l'entaille situee sur le joint. Cette methode est couplee a un algorithme qui permet une recherche exhaustive de tout l'espace parametrique. Cette technique permet d'extraire une zone d'incertitude reliee aux parametres du modele optimal. Une etude de sensibilite est egalement realisee sur l'identification. Plusieurs resultats de mesure sur des joints a recouvrements 1D et 2D sont realisees permettant ainsi l'etude de la repetabilite des resultats et la variabilite de differents cas d'endommagement. Les resultats de cette etude demontrent d'abord que la methode de detection proposee est tres efficace et permet de suivre la progression d'endommagement. De tres bons resultats de quantification et de localisation d'entailles ont ete obtenus dans les divers joints testes (1D et 2D). Il est prevu que l'utilisation d'ondes de Lamb permettraient d'etendre la plage de validite de la methode pour de plus petits dommages. Ces travaux visent d'abord la surveillance in-situ des structures de joint a recouvrements, mais d'autres types de defauts. (comme les disbond) et. de structures complexes sont egalement envisageables. Mots cles : joint a recouvrement, surveillance in situ, localisation et caracterisation de dommages

Translation into French of: “Changes to publication requirements made at the XVIII International Botanical Congress in Melbourne – what does e-publication mean for you?”. Translated by Christian Feuillet and Valéry Malécot Changements des conditions requises pour la publication faits au XVIII e Congrès International de Botanique à Melbourne – qu’est-ce que la publication électronique représente pour vous?

PubMed Central

Knapp, Sandra; McNeill, John; Turland, Nicholas J.

2011-01-01

Résumé Les changements au Code International de Nomenclature Botanique sont décidés tous les 6 ans aux Sections de Nomenclature associées aux Congrès Internationaux de Botanique (CIB). Le XVIIIe CIB se tenait à Melbourne, Australie; la Section de Nomenclature s’est réunie les 18-22 juillet 2011 et ses décisions ont été acceptées par le Congrès en session plénière le 30 juillet. Suite à cette réunion, plusieurs modifications importantes ont été apportées au Code et vont affecter la publication de nouveaux noms. Deux de ces changements prendront effet le 1er janvier 2012, quelques mois avant que le Code de Melbourne soit publié. Les documents électroniques publiés en ligne en ‘Portable Document Format’ (PDF) avec un ‘International Standard Serial Number’ (ISSN) ou un ‘International Standard Book Number’ (ISBN) constitueront une publication effective, et l’exigence d’une description ou d’une diagnose en latin pour les noms des nouveaux taxa sera changée en l’exigence d’une description ou d’une diagnose en latin ou en anglais. De plus, à partir du 1er janvier 2013, les noms nouveaux des organismes traités comme champignons devront, pour que la publication soit valide, inclure dans le protologue (tous ce qui est associé au nom au moment de la publication valide) la citation d’un identifiant (‘identifier’) fourni par un dépôt reconnu (tel MycoBank). Une ébauche des nouveaux articles concernant la publication électronique est fournie et des conseils de bon usage sont esquissés. Pour encourager la diffusion des changements adoptés au Code International de Nomenclature pour les algues, les champignons et les plantes, cet article sera publié dans BMC Evolutionary Biology, Botanical Journal of the Linnean Society, Brittonia, Cladistics, MycoKeys, Mycotaxon, New Phytologist, North American Fungi, Novon, Opuscula Philolichenum, PhytoKeys, Phytoneuron, Phytotaxa, Plant Diversity and Resources, Systematic Botany et Taxon. PMID:22287925

Caracterisation pratique des systemes quantiques et memoires quantiques auto-correctrices 2D

NASA Astrophysics Data System (ADS)

Landon-Cardinal, Olivier

Cette these s'attaque a deux problemes majeurs de l'information quantique: - Comment caracteriser efficacement un systeme quantique? - Comment stocker de l'information quantique? Elle se divise done en deux parties distinctes reliees par des elements techniques communs. Chacune est toutefois d'un interet propre et se suffit a elle-meme. Caracterisation pratique des systemes quantiques. Le calcul quantique exige un tres grand controle des systemes quantiques composes de plusieurs particules, par exemple des atomes confines dans un piege electromagnetique ou des electrons dans un dispositif semi-conducteur. Caracteriser un tel systeme quantique consiste a obtenir de l'information sur l'etat grace a des mesures experimentales. Or, chaque mesure sur le systeme quantique le perturbe et doit done etre effectuee apres avoir reprepare le systeme de facon identique. L'information recherchee est ensuite reconstruite numeriquement a partir de l'ensemble des donnees experimentales. Les experiences effectuees jusqu'a present visaient a reconstruire l'etat quantique complet du systeme, en particulier pour demontrer la capacite de preparer des etats intriques, dans lesquels les particules presentent des correlations non-locales. Or, la procedure de tomographie utilisee actuellement n'est envisageable que pour des systemes composes d'un petit nombre de particules. Il est donc urgent de trouver des methodes de caracterisation pour les systemes de grande taille. Dans cette these, nous proposons deux approches theoriques plus ciblees afin de caracteriser un systeme quantique en n'utilisant qu'un effort experimental et numerique raisonnable. - La premiere consiste a estimer la distance entre l'etat realise en laboratoire et l'etat cible que l'experimentateur voulait preparer. Nous presentons un protocole, dit de certification, demandant moins de ressources que la tomographie et tres efficace pour plusieurs classes d'etats importantes pour l'informatique quantique. - La seconde approche, dite de tomographie variationnelle, propose de reconstruire l'etat en restreignant l'espace de recherche a une classe variationnelle plutot qu'a l'immense espace des etats possibles. Un etat variationnel etant decrit par un petit nombre de parametres, un petit nombre d'experiences peut suffire a identifier les parametres variationnels de l'etat experimental. Nous montrons que c'est le cas pour deux classes variationnelles tres utilisees, les etats a produits matriciels (MPS) et l'ansatz pour intrication multi-echelle (MERA). Memoires quantiques auto-correctrices 2D. Une memoire quantique auto-correctrice est un systeme physique preservant de l'information quantique durant une duree de temps macroscopique. Il serait done l'equivalent quantique d'un disque dur ou d'une memoire flash equipant les ordinateurs actuels. Disposer d'un tel dispositif serait d'un grand interet pour l'informatique quantique. Une memoire quantique auto-correctrice est initialisee en preparant un etat fondamental, c'est-a-dire un etat stationnaire de plus basse energie. Afin de stocker de l'information quantique, il faut plusieurs etats fondamentaux distincts, chacun correspondant a une valeur differente de la memoire. Plus precisement, l'espace fondamental doit etre degenere. Dans cette these, on s'interesse a des systemes de particules disposees sur un reseau bidimensionnel (2D), telles les pieces sur un echiquier, qui sont plus faciles a realiser que les systemes 3D. Nous identifions deux criteres pour l'auto-correction: - La memoire quantique doit etre stable face aux perturbations provenant de l'environnement, par exemple l'application d'un champ magnetique externe. Ceci nous amene a considerer les systemes topologiques 2D dont les degres de liberte sont intrinsequement robustes aux perturbations locales de l'environnement. - La memoire quantique doit etre robuste face a un environnement thermique. Il faut s'assurer que les excitations thermiques n'amenent pas deux etats fondamentaux distincts vers le meme etat excite, sinon l'information aura ete perdue. Notre resultat principal montre qu'aucun systeme topologique 2D n'est auto-correcteur: l'environnement peut changer l'etat fondamental en deplacant aleatoirement de petits paquets d'energie, un mecanisme coherent avec l'intuition que tout systeme topologique admet des excitations localisees ou quasiparticules. L'interet de ce resultat est double. D'une part, il oriente la recherche d'un systeme auto-correcteur en montrant qu'il doit soit (i) etre tridimensionnel, ce qui est difficile a realiser experimentalement, soit (ii) etre base sur des mecanismes de protection nouveaux, allant au-dela des considerations energetiques. D'autre part, ce resultat constitue un premier pas vers la demonstration formelle de l'existence de quasiparticules pour tout systeme topologique.

Water Awareness Through Environmental Restoration

NASA Astrophysics Data System (ADS)

Davis-Caldwell, K.

2012-04-01

This poster will highlight a series of project based activities carried out at Hammond Elementary School in Laurel, Maryland, USA. All of the featured projects revolve around the school's Green School Initiative or an integral part of the science curricula. The Maryland Green School program was developed by a diverse team of educators representing the Maryland Association for Environmental and Outdoor Education (MAEOE), Office of the Governor, the Maryland Association of Student Councils, Maryland Department of Education, Department of Natural Resources and Maryland Department of the Environment. The program is administered through the Maryland Association for Environmental and Outdoor Education. The Maryland Green Schools Award Program recognizes Maryland schools that include environmental education in the curricula, model best management practices at the school and address community environmental issues. Among these numerous projects water is a common thread. Hammond Elementary School lies within the Chesapeake Bay watershed which stretches across 64,000 square miles and encompasses the entire District of Columbia. Educational components address habitats, tributaries and, the estuary system. The projects being highlighted in the poster will include: Trout to Streams Project: This 4th grade project focuses on the natural filtration system that area trout provide to the local and global waterways. As students learn about the importance of various fish to the watershed, they come to understand the effect of changes in the population of fish species due to consumption and pollution. The service learning project highlighted teaches students about water quality as they raise trout eggs and monitor their development into hatching and later stream release. Buffer Streams Tree Planting Projects: This 5th grade science service learning project allows students to investigate the water quality and conditions of local area streams. This project teaches students the positive and negative effects of human presence on the local and global water supply. Student research scientifically tested ways to slow down the effects of run-off contaminants. Students also revisit water analysis and plant trees as buffers as part of their stream preservation efforts in a culminating activity. Oyster Reef Restoration Project: As a result of changes in climate, pollution and human consumption, the oyster population in the Chesapeake Bay had previously been on a rapid decline. The Oyster Reef Restoration Project allows students to understand the creatures of the bay and the cause of this decline. They explore the domino effect this has had on the quality of the water in the bay and future implications on the environment when the oyster population fluctuates significantly. Students construct concrete reefs and study the components of its contents and the reef's impact on the bay. Students are responsible for mixing, pouring and preparing the reef for its eventual drop in the bay. Wetlands Recovery: Following the elimination of a substantial amount of the natural wetlands behind the elementary and middle schools, a wetlands area was erected on the school grounds. This pond has been used to learn about habitats and the role humans, plants and organisms play in the preservation of the earth soil and water supply. This wetland is used by both the elementary and middle schools as a place for hands-on inquiry based learning. Students maintain the upkeep of the pond and teach other students at lower grades.

A miniaturized counting technique for anaerobic bacteria.

PubMed

Sharpe, A N; Pettipher, G L; Lloyd, G R

1976-12-01

A miniaturized counting technique gave results as good as the pour-plate and Most Probable Number (MPN) techniques for enumeration of clostridia spp. and anaerobic isolates from the gut. Highest counts were obtained when ascorbic acid (1%) and dithiothreitol (0.015%) were added to the reinforced clostridial medium used for counting. This minimized the effect of exposure to air before incubation. The miniature technique allowed up to 40 samples to be plated and incubated in one McIntosh-Filde's-type anaerobic jar, compared with 3 or 4 by the normal pour plate.

Guidance and Control Technology for Highly Integrated Systems.

DTIC Science & Technology

1981-02-08

fonctions. 11 s’agit en fait d’un probl ~me 6conomique de redondance du mat6riel et de redondance entre les sysemes - en ce qui concerne lea pannes, la...le brouillage pour lingual ii ne se pose qua le probl ~me de compatibilit6. 3 - La NIS bande L eat par contra envisag6 pour assurer in haut nivesu de... management considerably. The 5INTAC-3 is in the global system catenory : NIS L BAND + 3TID5 DTDMA optimized : - the message is distributed both For

Helicopter Guidance and Control Systems for Battlefield Support Held at Monterey, California on 8-11 May 1984.

DTIC Science & Technology

1984-08-01

order to arrive at ACPs or the objective on time. Timely arrival is particularly critical in crossing friendly lines at scheduled air passage points...permet dsp~rer quo dons l’avenir ii sera possible do stocker des * cartes "digitalisges" mais pour lea annfies qui viennent Ie film couleur rests de...trls loin Is "mimoirs" Is plus 6conomiqus. .9 La figure 2 montre is princips rstenu pour Ia rfialisation d’un film coulour do 35 m d’une longusur

Ship Dynamics Identification Using Simulator and Sea Trial Data

DTIC Science & Technology

2002-04-29

Committee "© Her Majesty the Queen as represented by the Minister of National Defence, 2002 "© Sa majest6 la reine, repr~sent~e par le ministre de la...cotes d’instructeurs. Le but du present rapport est de ddterminer la nature de la dynamique des navires virtuels et r6els de mani&re A ce que des...la dynamique du navire. Le pr6sent document pr6cise la dynamique du navire pour un navire de classe Bay des FC, ainsi que pour un navire simul6. Les

SOA Challenges for Real-Time and Disadvantaged Grids (Defis de la SOA pour les reseaux defavorises et en temps reel)

DTIC Science & Technology

2014-04-01

des améliorations mesurables de la capacité de traitement des messages. Plusieurs facteurs clés de réussite ont été identifiés, notamment...l’utilisation de normes ouvertes, la facilité de gestion et de configuration et la transparence pour l’utilisateur. L’infrastructure de messagerie doit...STO », « RTO » ou « AGARD » selon le cas, suivi du numéro de série. Des informations analogues, telles que

Environmentally Safe and Effective Processes for Paint Removal (Les Procedes Efficaces et Ecologiques pour l’Enlevement des Peintures)

DTIC Science & Technology

1993-03-01

1992 sur tine coclule d’avion TRANSALL pointe A loexception des composites vner / dpoxy (inhtalla- avec In garame Airbus . don non robotisde, 2 buses...Los P.M.P. h AIRBUS INDUSTRIE page P.M.P, cii cabine (MATRASUR ct SCHLICK) pour l’onl~vormont des peinturos sur las 616ments md- Ril~ant suite h uno...dtudo sur las P.M.P. lancdo fin caziiquos (site do MARIGNANE) =* capacitd do iral. 1987, tine spcificatlun do pr ddwv Airbus Industrie tement : 1500 kg

Separation of Target Rigid Body and Micro-Doppler Effects in ISAR/SAR Imaging

DTIC Science & Technology

2006-09-01

tour- nantes et vibrantes de la cible. De nouveaux algorithmes et m~thodes devront donc DRDC Ottawa TM 2006-187 v &tre 6tudi6s plus en profondeur afin...UNCLASSIFIED SECURITY CLASSIFICATION OF FORM Defence R&D Canada R & D pour la defense Canada Canada’s Leader in Defence Chef de file au Canada en mati~re and...I 1f1 Defence Research and Recherche et developpement Development Canada pour la defense Canada DEFENCE ril DEFENSE Separation of target rigid body

Technologies for Protection and Resistance Enhancement of Critical Infrastructures againstExtreme Fire

DTIC Science & Technology

2014-05-01

in Right of Canada, as represented by the Minister of National Defence, 2014 © Sa Majesté la Reine (en droit du Canada), telle que représentée par le ...extreme fire protection of critical infrastructures. Résumé …..... Le présent rapport fournit de l’information qui pourrait aider à élaborer des...démarches nationales pour une atténuation du risque émergeant des conditions d’incendie extrêmes pour les infrastructures essentielles (IE). Les résultats

Application of Hierarchical Goal Analysis to the Halifax Class Frigate Operations Room: A Case Study

DTIC Science & Technology

2007-11-01

actuelle en fonction de son niveau de soutien pour ces diverses dépendances. Les auteurs prévoient que la même méthode peut être utilisée pour décrire...analysis. The focus of this paper is on the practice rather than the theory of HGA. Therefore, the next section contains only a brief summary of the...is based on Perceptual Control Theory [17], which posits that humans operate as perceptually driven, goal referenced, feedback systems, in that all

Choice for All: Proceedings of the International Conference of the Association for the Advancement of Rehabilitation Technology = Choix pour tous: Conference internationale pour le developpement de la technologie en readaptation (3rd, Montreal, Quebec, Canada, June 25-30, 1988). ICAART Volume III.

ERIC Educational Resources Information Center

RESNA: Association for the Advancement of Rehabilitation Technology, Washington, DC.

These proceedings were composed of 290 papers, submitted by 700 authors from 15 countries, in the field of rehabilitation engineering and technology. Of the 290 papers, 13 are written in French. Papers are generally two to four pages in length, and are organized within the following areas of rehabilitation technology: service delivery practice (15…

Partners in Quality: Tools for Practitioners in Child Care Settings. Standards of Practice, Code of Ethics, Guide to Self-Reflection = Partenaires pour la qualite: Outils pour les intervenantes des divers milieux de garde d'enfants. Normes de pratique, Code de deontologie, Guide d'introspection.

ERIC Educational Resources Information Center

Doherty, Gillian

Partners in Quality is a research and development project sponsored by the Canadian Child Care Federation and its affiliates to explore how child care providers, parents, and other partners can work together to support and improve quality in child care. This booklet, in both English and French, supplements a series to support child care providers…

The Origins and Adaptations of the Principles of War

DTIC Science & Technology

1975-06-06

from Josini’ s writings: 4 Gouvion de Saint Cyr, M6moires pour servir A l’histoire ailitaire, sous le Directoire, le Consulat, et l’Fmpire, Vol 1. As...18See Frederick II, Instruction pour les Sfntraux qui auront , commander des detachments, des siles, des secondes lignes et des aries prussiennes [(Berlin...principles. Emile, Mayer argued in La thdorie de la guerre et l’Otude de lPart militp’ire against the idea that while the methods of the military art vary

29. SOUTHEAST ACROSS BLACKSMITH SHOP AREA TOWARD TWO CIRCA 1900 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. SOUTHEAST ACROSS BLACKSMITH SHOP AREA TOWARD TWO CIRCA 1900 DRILL PRESSES ALONG THE EAST INTERIOR WALL AT THE NORTHEAST CORNER OF THE FACTORY BUILDING. THE HOODED FORGE IS VISIBLE IN THE LEFT FOREGROUND, SHOWING LADLES USED FOR POURING BABBITT BEARINGS. MOUNTED ON THE WORK BENCH IS THE MAIN CASTING FROM AN ELI WINDMILL, USED AS A JIG TO SUPPORT PARTS DURING THE BABBITT BEARING POURING OPERATION. THE WALL ABOVE THE WORKBENCH SHOWS THE BOARDED-UP OPENING FOR A FORMER WINDOW. - Kregel Windmill Company Factory, 1416 Central Avenue, Nebraska City, Otoe County, NE

Scheduling for Multifunction Radar via Two-Slope Benefit Functions

DTIC Science & Technology

2010-12-01

planification des visées de suivi et de surveillance pour un radar multifonc- tion. Une technique séquentielle est proposée, selon laquelle on planifie...toutes les demandes de visées. On examine la planification des visées de suivi et de surveillance. Ces travaux proposent une méthode de planification ... planification anticipée et tardive. La méthode proposée pour établir l’ordre de priorité des visées de surveillance permet de réobserver des

Measurements and Analysis of Reverberation, Target Echo and Clutter

DTIC Science & Technology

2013-12-01

réverbération pour prendre en charge les environne- ments dont les caractéristiques varient fortement en fonction de la distance ainsi que la géométrie...de faisceaux de réseaux remorqués dans un environnement dont les caractéristiques varient fortement en fonction de la distance ; (v) travaux...réverbération en mode normal pour prendre en charge la réverbération du sous-sol du fond, y compris dans les environnements dont les

Responsible health insurance revisited: pouring liberal wine into a conservative bottle.

PubMed

Seidman, Laurence

2005-01-01

In 1991, an article appeared proposing a plan for "Responsible National Health Insurance" (RHI) that contained three crucial elements supported by economists affiliated with two conservative policy institutions (the American Enterprise Institute and the Heritage Foundation). The central purpose of this article is to revisit RHI in light of developments over the past decade, and to make the case that liberals, rather than reject RHI, now should support it, provided conservatives agree to sufficient funding. In this article, I recommend "pouring liberal wine into this conservative bottle."

Peut-on améliorer la motivation des étudiants en médecine pour un cours fondamental de physiologie en intégrant à l’exposé magistral quelques méthodes pédagogiques actives?

PubMed Central

Bentata, Yassamine; Delfosse, Catherine

2017-01-01

La motivation des étudiants est une condition essentielle à l’apprentissage et la perception qu’a l’étudiant de la valeur qu’il accorde à une activité est l’une des trois composantes majeures de cette motivation. Comment amener les étudiants à percevoir l’utilité et l’intérêt de leurs cours universitaires tout en suscitant leur motivation ? L’objectif de l’étude est de déterminer la perception de la valeur attribuée par les étudiants au cours fondamental de physiologie et d’évaluer l’impact de l’intégration de quelques méthodes d’apprentissage actif aux exposés magistraux sur la motivation des étudiants du premier cycle des études médicales dans une jeune faculté. Cette étude prospective, a concerné les étudiants de deuxième année de médecine (PCEM2). Nous avons procédé initialement à une appréciation de la perception de la motivation des étudiants pour les cours universitaires via un premier questionnaire, après nous avons intégré deux activités pédagogiques: l’étude de cas et la réalisation de carte conceptuelle aux exposés magistraux du module de physiologie et à la fin nous avons évalué via un deuxième questionnaire l’impact de ces deux activités sur la motivation des étudiants. 131 et 109 étudiants ont rempli et rendu respectivement le 1er et le 2ème questionnaire parmi les 249 étudiants inscrits en PCEM2. La motivation de nos étudiants à l’égard de leurs cours universitaires était globalement très favorable, même si la motivation pour le cours de physiologie (70,8%) était légèrement moins importante que pour l’ensemble des cours (80%). Nos étudiants avaient apprécié les deux activités proposées et seulement 13% (pour l’étude de cas) et 16,8% (pour la carte) ne se montraient pas satisfaits. 40,9% des étudiants avaient réalisé une carte conceptuelle et la qualité de ces productions, jugée sur l’identification des concepts et des liens inter concepts, était globalement satisfaisante pour une première expérience. Influencée par de multiples facteurs internes et externes, la motivation des étudiants reste une grande problématique en milieu universitaire. Dans ce contexte, une planification rigoureuse d’activités pédagogiques diversifiées et actives est l’une des principales portes offertes à l’enseignant pouvant susciter cette motivation. PMID:29721145

Parametrisation D'effets Non-Standard EN Phenomenologie Electrofaible

NASA Astrophysics Data System (ADS)

Maksymyk, Ivan

Cette these pat articles porte sur la parametrisation d'effets non standard en physique electrofaible. Dans chaque analyse, nous avons ajoute plusieurs operateurs non standard au lagrangien du modele standard electrofaible. Les operateurs non standard decrivent les nouveaux effets decoulant d'un modele sous-jacent non-specefie. D'emblee, le nombre d'operateurs non standard que l'on peut inclure dans une telle analyse est illimite. Mais pour une classe specifique de modeles sous-jacents, les effets non standard peuvent etre decrits par un nombre raisonnable d'operateurs. Dans chaque analyse nous avons developpe des expressions pour des observables electrofaibles, en fonction des coefficients des operateurs nouveaux. En effectuant un "fit" statistique sur un ensemble de donnees experimentales precises, nous avons obtenu des contraintes phenomenologiques sur ces coefficients. Dans "Model-Independent Global Constraints on New Physics", nous avons adopte des hypotheses tres peu contraignantes relatives aux modeles sous-jacents. Nous avons tronque le lagrangien effectif a la dimension cinq (inclusivement). Visant la plus grande generalite possible, nous avons admis des interactions qui ne respectent pas les symetries discretes (soit C, P et CP) ainsi que des interactions qui ne conservent pas la saveur. Le lagrangien effectif contient une quarantaine d'operateurs nouveaux. Nous avons determine que, pour la plupart des coefficients des nouveaux operateurs, les contraintes sont assez serrees (2 ou 3%), mais il y a des exceptions interessantes. Dans "Bounding Anomalous Three-Gauge-Boson Couplings", nous avons determine des contraintes phenomenologiques sur les deviations des couplages a trois bosons de jauge par rapport aux interactions prescrites par le modele standard. Pour ce faire, nous avons calcule les contributions indirectes des CTBJ non standard aux observables de basse energie. Puisque le lagrangien effectif est non-renormalisable, certaines difficultes techniques se posent: pour regulariser les integrales de Feynman les chercheurs se sont generalement servi de la methode de coupure, mais cette methode peut mener a des resultats incorrects. Nous avons opte pour une technique alternative: la regularisation dimensionnelle et la "soustraction minimale avec decouplage". Dans "Beyond S, T and U" nous presentons le formalisme STUVWX, qui est une extension du formalisme STU de Peskin et Takeuchi. Ces formalismes sont bases sur l'hypothese que la theorie sous-jacente se manifeste au moyen de self -energies de bosons de jauge. Ce type d'effet s'appelle 'oblique'. A la base du formalisme STU se trouve la supposition que l'echelle de la nouvelle physique, M, est beaucoup plus grande que q, l'echelle a laquelle on effectue des mesures. Il en resulte que les effets obliques se parametrisent par les trois variables S, T et U. Par contre, dans le formalisme STUVWX, nous avons admis la possibilite que M~ q. Dans "A Global Fit to Extended Oblique Parameters", nous avons effectue deux fits statistiques sur un ensemble de mesures electrofaibles de haute precision. Dans le premier fit, nous avons pose V=W=X=0, obtenant ainsi des contraintes pour l'ensemble {S,T,U}. Dans le second fit, nous avons inclus tous les six parametres.

Conception de lois de pilotage robustes et sequencement de gains par l'approche de systemes lineaires a parametres variants

NASA Astrophysics Data System (ADS)

Hentabli, Kamel

Cette recherche s'inscrit dans le cadre du projet de recherche Active Control Technology entre l'Ecole de Technologie Superieure et le constructeur Bombardier Aeronautique . Le but est de concevoir des strategies de commandes multivariables et robustes pour des modeles dynamiques d'avions. Ces strategies de commandes devraient assurer a l'avion une haute performance et satisfaire des qualites de vol desirees en l'occurrence, une bonne manoeuvrabilite, de bonnes marges de stabilite et un amortissement des mouvements phugoides et rapides de l'avion. Dans un premier temps, nous nous sommes principalement interesses aux methodes de synthese LTI et plus exactement a l'approche Hinfinity et la mu-synthese. Par la suite, nous avons accorde un interet particulier aux techniques de commande LPV. Pour mener a bien ce travail, nous avons envisage une approche frequentielle, typiquement Hinfinity. Cette approche est particulierement interessante, dans la mesure ou le modele de synthese est construit directement a partir des differentes specifications du cahier des charges. En effet, ces specifications sont traduites sous forme de gabarits frequentiels, correspondant a des ponderations en entree et en sortie que l'on retrouve dans la synthese Hinfinity classique. Par ailleurs, nous avons utilise une representation de type lineaire fractionnelle (LFT), jugee mieux adaptee pour la prise en compte des differents types d'incertitudes, qui peuvent intervenir sur le systeme. De plus, cette representation s'avere tres appropriee pour l'analyse de la robustesse via les outils de la mu-analyse. D'autre part, afin d'optimiser le compromis entre les specifications de robustesse et de performance, nous avons opte pour une structure de commande a 2 degres de liberte avec modele de reference. Enfin, ces techniques sont illustrees sur des applications realistes, demontrant ainsi la pertinence et l'applicabilite de chacune d'elle. Mots cles. Commande de vol, qualites de vol et manoeuvrabilite, commande robuste, approche Hinfinity , mu-synthese, systemes lineaires a parametres variants, sequencement de gains, transformation lineaire fractionnelle, inegalite matricielle lineaire.

Insecticide and Repellent Mixture Pour-On Protects Cattle against Animal Trypanosomosis

PubMed Central

Abdoulmoumini, Mamoudou; Zoli, Andre; Cene, Bylah; Adakal, Hassane; Bouyer, Jérémy

2016-01-01

Background African animal trypanosomosis (AAT), transmitted by tsetse flies and tick-borne diseases are the main constraints to livestock production in sub-Saharan Africa. Vector control methods such as pour-on offer individual protection against ticks but not against tsetse so far, for which protection has always been communal, through a reduction of their density. The latter requires the treatment of a large part of the herd in a given landscape and is not instantaneous. Methodology/Principal Findings Two prospective surveys were conducted to evaluate the efficacy and persistence of a pour-on formulation composed of cypermetrhin, chlorpyrifos, piperonyl butoxid and citronella (Vectoclor, CEVA Santé Animal). In experimental conditions, tsetse flies were exposed to treated and control cattle. Flies knockdown and engorgement rates were determined and the product persistence was assessed as the time for these parameters to drop below 50% (T50). T50 was 37 days (95%CI: [33–41] days) and 46 days (95%CI: [39–56] days) for the knockdown and engorgement rates respectively. In field conditions, two cattle herds were monitored following a case-control experimental design, in the Adamaoua region of Cameroon. One herd was treated once with Vectoclor pour-on (treated group) and the second used as a control group (not treated). Ticks infestation rate, trypanosomosis prevalence and packed-cell volume were measured over the two months following treatment. The treatment was highly effective against ticks with a complete elimination three days after application in the treated group. Trypanosomosis prevalence was also significantly reduced during the study (by 4, P<0.001) and PCV of the treated group increased significantly in the same time (P<0.001), contrary to the control group. Conclusions/Significance The protection of this new pour-on against tsetse bites and trypanosomosis is demonstrated here for the first time. Moreover, this insecticide and repellent mixture offer a longer persistence of the efficacy against both tsetse and ticks than similar products currently on the market. It offers a great new opportunity for an integrated AAT control strategy including the treatment of residual cases with trypanocides. It might also allow controlling the spread of resistance against these trypanocides. PMID:28027324

Conductivite dans le modele de Hubbard bi-dimensionnel a faible couplage

NASA Astrophysics Data System (ADS)

Bergeron, Dominic

Le modele de Hubbard bi-dimensionnel (2D) est souvent considere comme le modele minimal pour les supraconducteurs a haute temperature critique a base d'oxyde de cuivre (SCHT). Sur un reseau carre, ce modele possede les phases qui sont communes a tous les SCHT, la phase antiferromagnetique, la phase supraconductrice et la phase dite du pseudogap. Il n'a pas de solution exacte, toutefois, plusieurs methodes approximatives permettent d'etudier ses proprietes de facon numerique. Les proprietes optiques et de transport sont bien connues dans les SCHT et sont donc de bonne candidates pour valider un modele theorique et aider a comprendre mieux la physique de ces materiaux. La presente these porte sur le calcul de ces proprietes pour le modele de Hubbard 2D a couplage faible ou intermediaire. La methode de calcul utilisee est l'approche auto-coherente a deux particules (ACDP), qui est non-perturbative et inclue l'effet des fluctuations de spin et de charge a toutes les longueurs d'onde. La derivation complete de l'expression de la conductivite dans l'approche ACDP est presentee. Cette expression contient ce qu'on appelle les corrections de vertex, qui tiennent compte des correlations entre quasi-particules. Pour rendre possible le calcul numerique de ces corrections, des algorithmes utilisant, entre autres, des transformees de Fourier rapides et des splines cubiques sont developpes. Les calculs sont faits pour le reseau carre avec sauts aux plus proches voisins autour du point critique antiferromagnetique. Aux dopages plus faibles que le point critique, la conductivite optique presente une bosse dans l'infrarouge moyen a basse temperature, tel qu'observe dans plusieurs SCHT. Dans la resistivite en fonction de la temperature, on trouve un comportement isolant dans le pseudogap lorsque les corrections de vertex sont negligees et metallique lorsqu'elles sont prises en compte. Pres du point critique, la resistivite est lineaire en T a basse temperature et devient progressivement proportionnelle a T 2 a fort dopage. Quelques resultats avec sauts aux voisins plus eloignes sont aussi presentes. Mots-cles: Hubbard, point critique quantique, conductivite, corrections de vertex

Spectroscopie du Furanne et du Thiophene Par Diffusion Inelastique D'electrons

NASA Astrophysics Data System (ADS)

Lotfi, Said

Nous avons etudie les molecules de furanne ( rm C_4H_4O) et de thiophene (rm C_4H_4O) au moyen de la spectroscopie de diffusion inelastique d'electrons. Pour (rm C_4H_4O), les spectres realises dans differentes conditions d'energie d'impact et d'angle de diffusion contiennent des singularites ou des families de pics correspondant a: (1) des vibrations de l'etat fondamental dans le domaine 0-0.5 eV, (2) des etats triplets ^3 B_1 et ^3 A_1 qui dominent la region 3-5.5 eV, (3) des etats de valences, entre 5 et 10 eV, dont certains son accompagnes de progressions vibrationnelles, soit ~ A _1B_2, ~ B ^1A_1 et ~ C ^1A_1, (4) toujours entre 5 et 10 eV, deux series de Ryhdberg (rm 1a_2to nda_2 et rm 1a_2to npb_2) qui convergent vers la premiere limite d'ionisation de la molecule, avec une progression vibrationnelle associee au mdoe nu_4 pour la seconde, et une troisieme serie (rm 2b_1to nsa_1 ) convergent vers la seconde limite d'ionisation accompagnee de la progression de mode nu _1. Pour rm C_4H_4S, nos spectres presentent les memes etats de vibration et les memes etats triplets que pour rm C_4H _4O. Nous avons releve egalement, dans la region de 5 a 10 eV, des etats de valence ~ A ^1A_1 (ou ~ A ^1B_2), ~ B ^1A_1 (ou ~ B ^1B _2) et ~ C ^1A_1 (ou ~ C ^1B_2). Pour la premiere fois, par la spectroscopie de diffusion inelastique d'electrons, de nombreux pics ont ete identifies et attribues, dans le cadre de ce travail. Il s'agit, notamment, des etats de vibration de l'etat electronique fondamental de ces molecules et egalement de certains etats de Rydberg dans le cas du furanne.

Resistance to densification, tensile strength and capsule-filling performance of some pharmaceutical diluents.

PubMed

Nikolakakis, I; Aragon, O B; Malamataris, S

1998-07-01

The purpose of this study was to compare some indicators of capsule-filling performance, as measured by tapped density under different conditions, and elucidate possible quantitative relationships between variation of capsule fill-weight (%CV) and gravitational and inter-particle forces (attractive or frictional) derived from measurements of particle size, true density, low compression and tensile strength. Five common pharmaceutical diluents (lactose, maize starch, talc, Emcocel and Avicel) were investigated and two capsule-filling methods (pouring powder and dosator nozzle) were employed. It was found that for the pouring-type method the appropriateness of Hausner's ratio (HR), Carr's compressibility index (CC%) and Kawakita's constant (alpha) as indicators of capsule fill-weight variation decreases in the order alpha > CC% > HR; the appropriateness of these indicators also decreases with increasing cylinder size and with impact velocity during tapping. For the dosator-type method the appropriateness of the indicators decreases in the order HR > CC% > alpha, the opposite of that for the pouring-type method; the appropriateness of the indicators increases with decreasing cylinder size and impact velocity. The relationship between %CV and the ratio of inter-particle attractive to gravitational forces calculated from measurements of particle size and true density (Fvdw/Wp) was more significant for the pouring-type capsule-filling method. For the dosator-type method a significant relationship (1% level) was found between %CV and the product of Fvdw/Wp and a function expressing the increase, with packing density (p(f)), in the ratio of frictional to attractive inter-particle forces derived from compression (P) and tensile-strength (T) testing, d(log(P/T))/d(p(f)). The value of tapped density in predictions of capsule-filling performance is affected by the testing conditions in a manner depending on the filling method applied. For the pouring-type method predictions can be based on the ratio of attractive (inter-particle) to gravitational forces, whereas for the dosator-type method the contribution of frictional and attractive forces should, because of packing density change, also be taken into account.

Crystal accumulation in the Hanford Waste Treatment Plant high level waste melter: Summary of FY2016 experiements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K.; Fowley, M.; Miller, D.

2016-12-01

Five experiments were completed with the full-scale, room temperature Hanford Waste Treatment and Immobilization Plant (WTP) high-level waste (HLW) melter riser test system to observe particle flow and settling in support of a crystal tolerant approach to melter operation. A prototypic pour rate was maintained based on the volumetric flow rate. Accumulation of particles was observed at the bottom of the riser and along the bottom of the throat after each experiment. Measurements of the accumulated layer thicknesses showed that the settled particles at the bottom of the riser did not vary in thickness during pouring cycles or idle periods.more » Some of the settled particles at the bottom of the throat were re-suspended during subsequent pouring cycles, and settled back to approximately the same thickness after each idle period. The cause of the consistency of the accumulated layer thicknesses is not year clear, but was hypothesized to be related to particle flow back to the feed tank. Additional experiments reinforced the observation of particle flow along a considerable portion of the throat during idle periods. Limitations of the system are noted in this report and may be addressed via future modifications. Follow-on experiments will be designed to evaluate the impact of pouring rate on particle re-suspension, the influence of feed tank agitation on particle accumulation, and the effect of changes in air lance positioning on the accumulation and re-suspension of particles at the bottom of the riser. A method for sampling the accumulated particles will be developed to support particle size distribution analyses. Thicker accumulated layers will be intentionally formed via direct addition of particles to select areas of the system to better understand the ability to continue pouring and re-suspend particles. Results from the room temperature system will be correlated with observations and data from the Research Scale Melter (RSM) at Pacific Northwest National Laboratory, and coordinated with modeling efforts underway at Idaho National Laboratory.« less

Fréquence et caractéristiques des AVC impliquant les artères perforantes dans le Service de Neurologie de l’Hopital Bafelatanana, Antananarivo

PubMed Central

Rasaholiarison, Nomena Finiavana; Randrianasolo, Rahamefy Odilon; Rajaonarison, Lala Andriamasinavalona; Rakotomanana, Jenny Larissa; Razafimahefa, Julien; Tehindrazanarivelo, Alain Djacoba

2017-01-01

Introduction Les accidents vasculaires cérébraux des artères perforantes sont surtout des artériolopathies. Ils évoluent vers la démence et la récurrence. Pour mieux prévenir ces complications notre étude avait pour but d'évaluer la fréquence et les caractéristiques de ces AVC. Méthodes c'est une étude descriptive rétrospective du 01 Mars au 25 Septembre 2015 au service de Neurologie CHU-JRB. Ont été inclus les patients présentant un déficit neurologique brutal et un scanner cérébral avec atteinte du territoire profonde. Les caractéristiques des AVC des artères perforantes ont été recueillies. Les données étaient traitées par le logiciel SPSS 20. Résultats Quatre-vingt-trois (48,25%) patients avaient des AVC des artères perforantes sur 172 AVC. Pour les AVC des artères perforantes la population était jeune avec 65,06% moins de 65 ans et à prédominance masculine avec 61,44%. Les formes hémorragiques étaient à 67,46%. Trente et un patients (37,34%) ont connu des récurrences et parmi eux presque le quart avait 2 récurrences avec 38,70% en moins de un an. Tous les patients avec récurrence avaient un trouble dysexécutif (p < 0,0001) et une mauvaise observance thérapeutique d'antihypertenseur. La mortalité n'était qu'à 6,02% pour ces types d'AVC pendant l'hospitalisation. Conclusion Un suivi spécifique en neurologie est nécessaire dès le premier accident vasculaire cérébral d'artère perforante pour dépister un début de démence et prévenir les récurrences. PMID:29255546

Delineation of a Re-establishing Drainage Network Using SPOT and Landsat Images

NASA Astrophysics Data System (ADS)

Bailey, J. E.; Self, S.; Mouginis-Mark, P. J.

2008-12-01

The 1991 eruption of Mt. Pinatubo, The Philippines, provided a unique opportunity to study the effects on the landscape of a large eruption in part because it took place after the advent of regular satellite-based observations. The eruption formed one large (>100km2) ignimbrite sheet, with over 70% of the total deposit deposited in three primary drainage basins to the west of the volcano. High-resolution (20 m/pixel) satellite images, showing the western drainage basins and surrounding region both before and after the eruption were used to observe the re-establishment and evolution of drainage networks on the newly emplaced ignimbrite sheet. Changes in the drainage networks were delineated from a time series of SPOT (Satellite Pour l'Observation de la Terre) and Landsat multi-spectral satellite images. The analysis of which was supplemented by ground- based observations. The satellite images showed that the blue prints for the new drainage systems were established early (within days of the eruption) and at a large-scale followed the pre-eruption pattern. However, the images also illustrated the ephemeral nature of many channels due to the influence of secondary pyroclastic flows, lahar- dammed lake breakouts, stream piracy and shifts due to erosion. Characteristics of the defined drainage networks were used to infer the relative influence on the lahar hazard within each drainage basin.

Spiral Salmonella assay: validation against the standard pour-plate assay.

PubMed

Diehl, M; Fort, F

1996-01-01

The spiral Ames assay, an automated approach to bacterial mutagenicity testing which simplifies the test procedure and reduces the amount of drug required to generate mutagenic dose-response information, has been evaluated and validated for routine screening. The spiral plater delivers the Salmonella bacteria, exogenous metabolic activation system and drug to the surface of a rotating agar plate one on top of another in such a way that a uniform density of bacteria is exposed to a logarithmically decreasing volume of drug. Following an incubation of 48 hr at 37 degrees C, the plates are scanned by a laser counter, and the data are subjected to a computerized analysis. Petri plates of 15 cm diameter were used to provide a concentration range of about 250-fold per plate. The Salmonella were concentrated 20-fold to increase sensitivity. Thirty-eight compounds from a variety of chemical classes, including both pharmaceuticals and known mutagens of moderate to strong potency, were tested in both the spiral and the standard pour-plate assays. There was overall test agreement on positive or negative results for 82% of the compounds tested. When only the results from strains TA98 plus TA100 were considered, the agreement was 87%. When positive results were obtained, the fold increase over vehicle control was on average twice as great for the spiral assay compared to the pour-plate assay. It was concluded that the two assay procedures generally provided comparable results, with the spiral assay being somewhat more sensitive in terms of dose-response than the pour-plate assay.

Utilisation de la mélatonine pour le sommeil chez les enfants en bonne santé

PubMed Central

Janjua, Irvin; Goldman, Ran D.

2016-01-01

Résumé Question Une maman a amené son garçon de 12 ans me consulter à mon bureau. Elle s’inquiète, car il a de la difficulté à s’endormir presque tous les soirs. Elle travaille par quarts et elle prend elle-même de la mélatonine pour l’aider à s’endormir. Elle m’a demandé si son garçon pouvait aussi prendre de la mélatonine. Quels sont les recommandations et les éléments à considérer avant d’utiliser la mélatonine chez les enfants et les adolescents en bonne santé? Réponse L’insomnie est rapportée chez jusqu’à un quart des enfants en bonne santé et chez les trois quarts des enfants atteints d’une affection psychiatrique ou neurodéveloppementale, ce qui entraîne des conséquences négatives. Pour les enfants atteints du syndrome de retard de phase du sommeil, la mélatonine pourrait s’avérer utile lorsque jumelée à une évaluation de l’insomnie et à un suivi régulier. La mélatonine pourrait être envisagée pour des enfants sans diagnostic d’insomnie qui ont une bonne hygiène du sommeil. Bien qu’elle semble sans danger, il n’existe pas de données probantes en faveur de l’emploi systématique de la mélatonine chez les enfants en bonne santé.

Hydrodynamique dans les milieux gaz/liquide non-newtoniens, agités mécaniquement, étude de l'hélice à profil mince [HPM] et de la turbine à disque de Rushton

NASA Astrophysics Data System (ADS)

Loukili, A.; Desplanches, H.; Gaston Bonhomme, Y.; Chevalier, J. L.; Bruxelmane, M.; Ouazzani Chahdi, T.; El Ghadraoui, H.

1999-03-01

The power consumption is measured for non-newtonian gas-liquid systems. The useful zone situated beyond the flooding point was defined by using the power caracteristics plot and hydrodynamic observations. Correlations were established in dimensional or adimensional form, to estimate the stirrer speed at the flooding point, and the power consumption in the working zone. Those correlations established in a large scale of rheological behaviour, for two kind of impellers in different geometrical ratios and for two tanks for scaling up, are used to compare an axial impeller (the thinny profile propeller) to a radial one (the Rushton's disc turbine). La puissance d'agitation est mesurée pour des systèmes gaz-liquides non-newtoniens rhéofluidifiants. Le domaine utile de fonctionnement du réacteur gaz-liquide, situé au-delà du point de désengorgement complet, est défini à partir de la courbe caractéristique de puissance et d'observations hydrodynamiques. Des corrélations sont établies sous forme dimensionnelle ou adimensionnelle pour prédire la vitesse d'agitation au point de charge, et la puissance consommée dans la zone utile. Ces corrélations définies pour une gamme étendue de comportements rhéofluidifiants, pour différentes géomètries de mobiles et sur deux tailles de cuves en extrapolation, permettent en outre de comparer deux mobiles, l'un axial et l'autre radial.

Approches pour la reduction de l'impact de defaut dans le transport d'energie du parc eolien offshore via VSC-HVDC =

NASA Astrophysics Data System (ADS)

Benadja, Mounir

Dans ce travail est presente un systeme de generation d'energie d'un parc eolien offshore et un systeme de transport utilisant les stations VSC-HVDC connectees au reseau principal AC onshore. Trois configurations ont ete etudiees, modelisees et validees par simulation. Dans chacune des configurations, des contributions ameliorant les cotes techniques et economiques sont decrites ci-dessous : La premiere contribution concerne un nouvel algorithme MPPT (Maximum Power Point Tracking) utilise pour l'extraction de la puissance maximale disponible dans les eoliennes des parcs offshores. Cette technique d'extraction du MPPT ameliore le rendement energetique de la chaine de conversion des energies renouvelables notamment l'energie eolienne a petite et a grande echelles (parc eolien offshore) qui constitue un probleme pour les constructeurs qui se trouvent confrontes a developper des dispositifs MPPT simples, moins couteux, robustes, fiables et capable d'obtenir un rendement energetique maximal. La deuxieme contribution concerne la reduction de la taille, du cout et de l'impact des defauts electriques (AC et DC) dans le systeme construit pour transporter l'energie d'un parc eolien offshore (OWF) vers le reseau principal AC onshore via deux stations 3L-NPC VSCHVDC. La solution developpee utilise des observateurs non-lineaires bases sur le filtre de Kalman etendu (EKF). Ce filtre permet d'estimer la vitesse de rotation et la position du rotor de chacune des generatrices du parc eolien offshore et de la tension du bus DC de l'onduleur DC-AC offshore et des deux stations 3L-NPC-VSC-HVDC (offshore et onshore). De plus, ce developpement du filtre de Kalman etendu a permis de reduire l'impact des defauts AC et DC. Deux commandes ont ete utilisees, l'une (commande indirect dans le plan abc) avec EKF integre destinee pour controler le convertisseur DC-AC offshore et l'autre (commande d-q) avec EKF integre pour controler les convertisseurs des deux stations AC-DC et DC-AC tout en tenant compte des entrees de chacune des stations. L'integration des observateurs non-lineaires (EKF) dans le controle des convertisseurs permet de resoudre le probleme des incertitudes de mesure, des incertitudes dans la modelisation, en cas du dysfonctionnement ou de panne des capteurs de mesure ainsi que le probleme de l'impact des defauts (AC et DC) sur la qualite d'energie dans les systemes de transmission. Ces estimations contribuent a rendre le cout global du systeme moins cher et sa taille moins encombrante ainsi que la reduction de l'impact des defauts (AC et DC) sur le systeme. La troisieme contribution concerne la reduction de la taille, du cout et de l'impact des defauts electriques (AC et DC) dans le systeme construit pour transporter l'energie d'un parc eolien offshore (OWF) vers le reseau principal AC onshore via deux stations VSC-HVDC. La solution developpee utilise des observateurs non-lineaires bases sur le filtre de Kalman etendu (EKF). Ce filtre permet d'estimer la vitesse de rotation et la position du rotor de chacune des generatrices du parc eolien et de la tension du bus DC de l'onduleur DC-AC offshore. La contribution porte surtout sur le developpement des deux commandes des deux stations. La premiere, la commande non-lineaire modifiee pour controler le premier convertisseur de la station VSC-HVDC offshore assurant le transfert de la puissance generee par le parc eolien vers la station VSC-HVDC onshore. La deuxieme commande non-lineaire modifiee avec integration de la regulation de la tension du bus DC et de la commande a modele de reference adaptative (MRAC) pour la compensation des surintensites et surtensions durant les defauts AC et DC. On peut constater que lors d'un defaut AC au PCC (Point of Common Coupling) du cote reseau onshore, la profondeur de l'impact du defaut AC sur l'amplitude des courants du reseau principal AC onshore qui etait reduit a 60% par les travaux de recherche (Erlich, Feltes et Shewarega, 2014), comparativement a la nouvelle commande proposee MRAC qui reduit la profondeur de l'impact a 35%. Lors de l'apparition des defauts AC et DC, une reduction de l'impact des defauts sur l'amplitude des courants de reseau AC terrestre et du temps de reponse a ete observee et la stabilite du systeme a ete renforcee par l'utilisation de la commande adaptative basee sur le modele de reference MRAC. La quatrieme contribution concerne une nouvelle commande basee sur le mode de glissement (SM) appliquee pour la station VSC-HVDC qui relie le parc eolien offshore (OWF) au reseau principal AC. Ce parc est compose de dix eoliennes basees sur des generatrices synchrones a aimant permanent (VSWT/PMSGs) connectees en parallele et chacune est controlee par son propre convertisseur DC-DC. Une comparaison des performances entre la commande SM et de la commande non-lineaire avec des controleurs PI pour les deux conditions (presence et absence de defaut DC) a ete analysee et montre la superiorite de la commande par SM. Un prototype du systeme etudie a echelle reduite a ete realise et teste au laboratoire GREPCI en utilisant la carte dSPACE-DS1104 pour la validation experimentale. L'analyse et la simulation des systemes etudies sont developpees sous l'environnement Matlab/Simulink/Simpowersystem. Les resultats obtenus a partir des configurations developpees sont valides par simulation et par experimentation. Les performances sont tres satisfaisantes du point de vue reponse dynamique, reponse en regime permanent, stabilite du systeme et qualite de l'energie.

Glycolic acid physical properties and impurities assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D. P.; Pickenheim, B. R.; Hay, M. S.

This document has been revised to add analytical data for fresh, 1 year old, and 4 year old glycolic acid as recommended in Revision 2 of this document. This was needed to understand the concentration of formaldehyde and methoxyacetic acid, impurities present in the glycolic acid used in Savannah River National Laboratory (SRNL) experiments. Based on this information, the concentration of these impurities did not change during storage. These impurities were in the glycolic acid used in the testing included in this report and in subsequent testing using DuPont (now called Chemours) supplied Technical Grade 70 wt% glycolic acid. However,more » these impurities were not reported in the first two versions of this report. The Defense Waste Processing Facility (DWPF) is planning to implement a nitric-glycolic acid flowsheets to increase attainment to meet closure commitment dates during Sludge Batch 9. In fiscal year 2009, SRNL was requested to determine the physical properties of formic and glycolic acid blends.« less

Defense Waste Processing Facility Nitric- Glycolic Flowsheet Chemical Process Cell Chemistry: Part 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zamecnik, J.; Edwards, T.

The conversions of nitrite to nitrate, the destruction of glycolate, and the conversion of glycolate to formate and oxalate were modeled for the Nitric-Glycolic flowsheet using data from Chemical Process Cell (CPC) simulant runs conducted by Savannah River National Laboratory (SRNL) from 2011 to 2016. The goal of this work was to develop empirical correlation models to predict these values from measureable variables from the chemical process so that these quantities could be predicted a-priori from the sludge or simulant composition and measurable processing variables. The need for these predictions arises from the need to predict the REDuction/OXidation (REDOX) statemore » of the glass from the Defense Waste Processing Facility (DWPF) melter. This report summarizes the work on these correlations based on the aforementioned data. Previous work on these correlations was documented in a technical report covering data from 2011-2015. This current report supersedes this previous report. Further refinement of the models as additional data are collected is recommended.« less

Ostéogenèse imparfaite type III de découverte tardive: à propos d'un cas

PubMed Central

Rachidi, Wafae; Nassar, Kawtar; Janani, Saadia; Mkinsi, Ouafa

2015-01-01

Patient âgé de 52 ans, était admis dans notre établissement pour des polyarthralgies chroniques, plutôt mécaniques, touchant spécialement les articulations du membre inférieur. L'interrogatoire retrouvait l'antécédent de fractures répétées depuis l'enfance, pour des traumatismes minimes, suite à des chutes par glissement. Les signes cliniques et radiologiques, notamment, les fractures récurrentes, sclérotiques bleues, hyperlaxité ligamentaire, dentinogenèse imparfaite, syndrome dysmorphique, ostéoporose densitométrique importante, plaidaient tous en faveur d'une ostéogénèse imparfaite type III. Le patient a initié le traitement, par prise régulière du calcium (1g/jour), supplémentation en vitamine D, et il est programmé pour perfusion de Bisphosphonate (Pamidronate 60mg). Ce cas illustre une forme rare de découverte tardive d'ostéogénèse imparfaite type III. PMID:25995811

Compactification de la Supergravite 10-D Sur les Varietes de Calabi-Yau

NASA Astrophysics Data System (ADS)

Gagnon, Michel

Les varietes de Calabi-Yau permettent une description relativement simple et assez juste de la realite. Recemment, de nombreuses equipes de recherche s'y sont interessees, en particulier P. Candelas, A. M. Dale, C. A. Lutken et R. Schimmrigk (13) qui ont propose une liste de 7868 configurations distinctes. Toutefois, nous croyons que certaines des techniques qui sont exploitees pour construire cette liste ne sont pas suffisamment justifiees et ont pour effet de soustraire a nos investigations bon nombre de configurations potentiellement interessantes. Ainsi, nous produisons, sans utiliser ces techniques simplificatrices, une liste de 97360 configurations. Ensuite, dans le cadre des modeles a 4 generations, nous appliquons un ensemble de criteres, fondes sur les symetries discretes, pour delimiter le domaine des configurations phenomenologiquement viables. Finalement, apres avoir fixe notre choix sur une configuration particuliere, nous essayons de montrer tout l'interet physique des varietes de Calabi-Yau en exposant certains aspects de la phenomenologie a basse energie, notamment les nombres quantiques, les spectres fermioniques, la brisure intermediaire du groupe de jauge et la duree de vie du proton.

Key process parameters to modify the porosity of cerium dioxide microspheres formed in the internal gelation process

DOE PAGES

Hunt, Rodney Dale; Collins, Jack Lee; Reif, Tyler J.; ...

2017-08-04

Recently, an internal gelation study demonstrated that the use of heated urea and hexamethylenetetramine can have a pronounced impact on the porosity and sintering characteristics of cerium dioxide (CeO 2) microspheres. This effort has identified process variables that can significantly change the initial porosity of the CeO 2 microspheres with slight modifications. A relatively small difference in the sample preparation of cerium ammonium nitrate and ammonium hydroxide solution had a large reproducible impact on the porosity and slow pour density of the produced microspheres. Increases in the gelation temperature as small as 0.5 K also produced a noticeable increase inmore » the slow pour density. If the gelation temperature was increased too high, the use of the heated hexamethylenetetramine and urea was no longer observed to be effective in increasing the porosity of the CeO 2 microspheres. In conclusion, the final process variable was the amount of dispersing agent, Span™ 80, which can increase the slow pour density and produce significantly smaller microspheres.« less

Arthroplastie totale du coude sur séquelles d'ostéoarthrite négligée-à propos d'un cas

PubMed Central

El Ibrahimi, Abdelhalim; Elidrissi, Mohammed; Shimi, Mohammed; Elmrini, Abdelmajid

2011-01-01

L'arthroplastie totale au cours des séquelles d'infection ostéo-articulaire a été destinée surtout pour la hanche et le genou. Cependant, peu de travaux ont étaient consacrée pour l'articulation du coude. Nous rapportons le cas d'une patiente, âgée de 26 ans, ayant présentée dans l'enfance une ostéoarthrite du coude traitée traditionnellement, mais qui a développé progressivement une instabilité sévère du coude. Après l'implantation d'une prothèse semi-contrainte de Coonrad-Morrey non cimentée, le résultat est très satisfaisant jusqu’à deux ans de recul, avec un gain de la mobilité en flexion de 110 degrés et en extension de 5 degrés, l'index de performance pour le coude selon la Mayo Clinic de 80/100. Nous n'avons pas de complication à déplorer. PMID:22355439

Profil épidémiologique des brûlés à Marrakech: à propos de 152 cas

PubMed Central

Ibnouzahir, M.; Ettalbi, S.; Ouahbi, S.; Droussi, H.; Sousou, M.; Chlihi, A.; Bahaichar, N.; Boukind, H.

2011-01-01

Summary Cet article concerne une étude épidémiologique rétrospective portant sur 152 patients brûlés hospitalisés entre 2006 et 2008. Les brûlés avaient moins de 20 ans dans 65% des cas. Le sex ratio (m/f) était de 1,18/1. L’origine thermique est incriminée dans 84% des cas. L’atteinte par flammes représente 56% des cas. La surface corporelle brûlée moyenne chez nos patients était de 28%, et les brûlures de deuxième degré étaient de loin les plus fréquentes. Dans notre série, le visage et le cou étaient le siège le plus fréquemment touché. La prévention reste la meilleure arme pour lutter contre ce fléau, et pour cela plusieurs mesures sont proposées pour améliorer l’état actuel des choses. PMID:21991231

A Novel Methodology for the Synthesis of Acyloxy Castor Polyol Esters: Low Pour Point Lubricant Base Stocks.

PubMed

Kamalakar, Kotte; Mahesh, Goli; Prasad, Rachapudi B N; Karuna, Mallampalli S L

2015-01-01

Castor oil, a non-edible oil containing hydroxyl fatty acid, ricinoleic acid (89.3 %) was chemically modified employing a two step procedure. The first step involved acylation (C(2)-C(6) alkanoic anhydrides) of -OH functionality employing a green catalyst, Kieselguhr-G and solvent free medium. The catalyst after reaction was filtered and reused several times without loss in activity. The second step is esterification of acylated castor fatty acids with branched mono alcohol, 2-ethylhexanol and polyols namely neopentyl glycol (NPG), trimethylolpropane (TMP) and pentaerythritol (PE) to obtain 16 novel base stocks. The base stocks when evaluated for different lubricant properties have shown very low pour points (-30 to -45°C) and broad viscosity ranges 20.27 cSt to 370.73 cSt, higher viscosity indices (144-171), good thermal and oxidative stabilities, and high weld load capacities suitable for multi-range industrial applications such as hydraulic fluids, metal working fluids, gear oil, forging and aviation applications. The study revealed that acylated branched mono- and polyol esters rich in monounsaturation is desirable for developing low pour point base stocks.

Méthode d'estimation des tassements des sols fins sous les remblais d'infrastructures ferroviaires pour lignes à grande vitesse

NASA Astrophysics Data System (ADS)

Said Alami, Soukaina; Reiffsteck, Philippe; Cuira, Fahd

2018-02-01

Le besoin de maîtriser les déformations des sols sous les remblais destinés à recevoir les structures de lignes à grande vitesse, en fait un enjeu important pour ces projets. Toutefois, de nombreuses difficultés ont été soulevées liées principalement au grand nombre d'incertitudes qui entourent le phénomène. En effet, la caractérisation géologique et géotechnique dépend de sondages et d'essais où le risque de remaniement est important et dont l'interprétation est, souvent, délicate. Cet article présente une procédure de calcul qui permettrait en pratique d'évaluer le tassement sous remblai avec une bonne précision et qui a été validée sur un certain nombre d'ouvrages. Pour cela, des corrections sont introduites aux méthodes usuelles de calcul permettant d'approcher les valeurs mesurées sur chantier.

Key process parameters to modify the porosity of cerium dioxide microspheres formed in the internal gelation process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunt, Rodney Dale; Collins, Jack Lee; Reif, Tyler J.

Recently, an internal gelation study demonstrated that the use of heated urea and hexamethylenetetramine can have a pronounced impact on the porosity and sintering characteristics of cerium dioxide (CeO 2) microspheres. This effort has identified process variables that can significantly change the initial porosity of the CeO 2 microspheres with slight modifications. A relatively small difference in the sample preparation of cerium ammonium nitrate and ammonium hydroxide solution had a large reproducible impact on the porosity and slow pour density of the produced microspheres. Increases in the gelation temperature as small as 0.5 K also produced a noticeable increase inmore » the slow pour density. If the gelation temperature was increased too high, the use of the heated hexamethylenetetramine and urea was no longer observed to be effective in increasing the porosity of the CeO 2 microspheres. In conclusion, the final process variable was the amount of dispersing agent, Span™ 80, which can increase the slow pour density and produce significantly smaller microspheres.« less

Analyse de plomb dans les peintures

NASA Astrophysics Data System (ADS)

Broll, N.; Frezouls, J.-M.

2002-07-01

The analysis of lead in paints was previously used for the characterisation of pigments. In this way, the analysis is able to specify the century of the painting of a work of art. Recently this technique was also used to determine the toxicity of lead paints in building. This paper compared the result of several X-ray fluorescence spectrometer, either wave length/energy dispersion laboratory apparatus or X-ray microtube/radioactive source portable equipment's. L'analyse du plomb dans les peintures a jusqu'à présent été appliquée essentiellement pour caractériser les pigments lors de leur fabrication et pour identifier des rouvres d'art. Récemment cette technique est également utilisée pour déterminer la toxicité des peintures au plomb dans les bâtiments. Nous avons comparé les performances de plusieurs spectromètres de fluorescence X, soit de laboratoire à dispersion en longueur d'onde ou à dispersion en énergie (avec tube à rayonsX), soit portable avec source radioactive ou tube à rayons X.

Le risque de détresse morale dans la pratique contemporaine des soins de santé.

PubMed

Austin, Wendy

2016-05-01

Les professionnels de la santé sont des agents moraux dont la relation fiduciaire avec le public est animée par la responsabilité et la promesse de puiser dans leurs connaissances et leurs habiletés pour aider les personnes sous leurs soins. Lorsque leur capacité à tenir cette promesse est freinée ou compromise, ils risquent de souffrir de détresse morale. Le concept de détresse morale est défini et mis en contexte dans le milieu de la santé. Les contraintes et les facteurs qui en sont à l'origine sont présentés, de même que les moyens utilisés par les professionnels de la santé et les organisations de santé pour la soulager. Un changement transformateur s'impose pour vaincre la culture du silence et maintenir un système de santé où il est possible de vivre avec sa conscience. © 2016 The Canadian College of Health Leaders.

Le surpoids, l’obésité et le contrôle glycémique chez les diabétiques du centre de référence provincial de diabète (CRD), Kénitra, Maroc

PubMed Central

Lotfi, Zeghari; Aboussaleh, Youssef; Sbaibi, Rachid; Achouri, Imane; Benguedour, Rachid

2017-01-01

Introduction Le diabète est définit comme un trouble de l'assimilation, de l'utilisation et du stockage des sucres apportés par l'alimentation, sa prise en charge est assurée par le suivi du surpoids et l'obésité et le contrôle glycémique régulier. L'objectif de ce travail était l'étude du surpoids, l'obésité et le contrôle glycémique chez 2227 diabétiques de différent type (type 1, 2 et gestationnel), consultants le centre de référence provincial de diabète (CRD), Kénitra-Maroc. Méthodes L'étude s'est déroulée sur une période d'une année du mois janvier au mois décembre 2015, L'évaluation du surpoids et l'obésité a été effectuée par le calcul de l'Indice de Masse Corporelle (IMC=Poids/Taille2 (Kg/m2)), elles sont définit respectivement par IMC > 25 Kg/m2, et IMC > 30 Kg/m2, le poids et la taille ont été mesurés selon les recommandations de l'organisation mondiale de santé (OMS), Le contrôle glycémique a été effectué par l'analyse sanguine de l'Hémoglobine glycosylée et de la Glycémie à jeun. Les normes sont 7% pour l'Hémoglobine glycosylée et 0,70g/l à 1,10g/l pour la Glycémie à jeun. Résultats L'intervalle d'âges des patients est compris entre 8 mois et 80 ans, avec une dominance des diabétiques provenant du milieu urbain (74%) par rapport à ceux provenant du milieu rural (26%). Le surpoids touche l'ensemble de cette population. L'IMC moyen des femmes tends vers l'obésité (IMC≈30): (29,21 Kg/m2 ± 3,1) pour le diabète gestationnel et (29,15 Kg/m2 ± 3,2) pour le diabète de type 2. Les valeurs du contrôle glycémique sont supérieures aux normes: avec 8,5% ± 2,6 > 7% pour l'hémoglobine glycosylée et 1,5 g/l ± 1,3 > 1,10g/l pour la Glycémie à jeun. La différence entre les valeurs de l'hémoglobine glycosylée entre les hommes (8,5 7% ± 2,6) et les femmes (8,1% ± 2,3) n'est pas significative (P > 0,05), même chose pour la Glycémie capillaire à jeun: pour les hommes (1,44 g/l ± 1,1) et les femmes (1,43 g/l ± 1,2). Les coefficients de corrélation de Pearson sont hautement significatifs (P<0,005); d'une part entre IMC et la Glycémie à jeun (r = 0,5) et d'autre part entre IMC et les valeurs de l'Hémoglobine glycosylée (r = 0,4). Conclusion L'ensemble des diabétiques présente des valeurs de l'IMC et du contrôle glycémique, supérieures aux normes. Des recherches approfondies sont nécessaires sur ces diabétiques afin de dresser un programme urgent de remédiation. PMID:28904714

Le pôle de métrologie de SOLEIL

NASA Astrophysics Data System (ADS)

Idir, M.; Brochet, S.; Delmotte, A.; Lagarde, B.; Mercere, P.; Moreno, T.; Polack, F.; Thomasset, M.

2006-12-01

Le Pôle de METROLOGIE de SOLEIL a pour objet de créer sur le synchrotron SOLEIL, une plateforme constituée : - une ligne de lumière utilisant le rayonnement synchrotron (métrologie dite à la longueur d'onde) - d'un laboratoire de métrologie associé (métrologie dite ll classique gg ) Ces deux types de Métrologie sont l'une et l'autre indispensables pour soutenir l'activité de recherche instrumentale en optique X et X-UV. Ce projet de pôle de METROLOGIE ne répondra pas seulement aux besoins des groupes chargés de l'équipement du synchrotron SOLEIL en optiques et détecteurs mais aussi pour préparer, tester et mettre au point les postes expérimentaux, ce qui concerne déjà une large communauté d'utilisateurs. Il sera aussi largement ouvert, dès sa mise en service, à l'ensemble de la communauté scientifique concernée par l'instrumentation X et XUV en Ile de France, en France, voire même en Europe si la demande continue de croître plus vite que l'offre dans ce domaine. Ligne de lumière Métrologie à la longueur d'onde La ligne de lumière sera équipée de plusieurs stations permettant de mesurer, dans la plus grande partie du spectre couvert par le synchrotron, les paramètres photométriques qui caractérisent les éléments optiques, tels que : la réflectivité de surfaces, l'efficacité de diffraction des réseaux, la diffusion des surfaces ou l'efficacité des détecteurs X et X-UV et la calibration absolue. Cette installation pourra servir également à développer des instruments et des diagnostics nécessaires à la caractérisation des faisceaux de rayons X (intensité, taille, degré de cohérence, polarisation etc.) Métrologie Classique La métrologie des surfaces optiques est devenue une nécessité critique pour les laboratoires et les industries qui utilisent les photons X et X-UV (synchrotrons, centres laser, etc. .). En effet, les progrès de calcul et de conception des systèmes optiques pour ces longueurs d'onde (optiques de microfocalisation, monochromateurs, diagnostics d'imagerie) font que les performances de ces instruments sont désormais limitées par les imperfections de fabrication des composants optiques. La métrologie des surfaces optiques est donc une nécessité impérieuse pour tous les acteurs du domaine, qui se doivent d'effectuer les contrôles appropriés. Cette pression s'exerce aussi sur les moyens utilisés pour effectuer ces mesures, car les incertitudes de mesure actuelles, notamment en ce qui concerne la régularité des surfaces, sont loin d'être négligeables vis à vis des tolérances demandées. Il est donc indispensable de faire évoluer les instruments de mesure et d'obtenir des gains significatifs de précision. Un travail particulier est en cours au laboratoire de Métrologie pour développer à côté des instruments commerciaux, des instruments prototypes sur des concepts originaux (mesures de profils de surface et mesures d'angle). Dans cet article, nous donnons des détails des choix techniques utilisés sur la ligne de METROLOGIE et TESTS et des performances attendues et nous décrirons le laboratoire de METROLOGIE en donnant des exemples d'optiques récemment testées.

Etude de la transmission sonore a travers un protecteur de type "coquilles" : modelisation numerique et validation experimentale

NASA Astrophysics Data System (ADS)

Boyer, Sylvain

On estime que sur les 3,7 millions des travailleurs au Quebec, plus de 500 000 sont exposes quotidiennement a des niveaux de bruits pouvant causer des lesions de l'appareil auditif. Lorsqu'il n'est pas possible de diminuer le niveau de bruit environnant, en modifiant les sources de bruits, ou en limitant la propagation du son, le port de protecteurs auditifs individualises, telles que les coquilles, demeure l'ultime solution. Bien que vue comme une solution a court terme, elle est communement employee, du fait de son caractere peu dispendieux, de sa facilite d'implantation et de son adaptabilite a la plupart des operations en environnement bruyant. Cependant les protecteurs auditifs peuvent etre a la fois inadaptes aux travailleurs et a leur environnement et inconfortables ce qui limite leur temps de port, reduisant leur protection effective. Afin de palier a ces difficultes, un projet de recherche sur la protection auditive intitule : " Developpement d'outils et de methodes pour ameliorer et mieux evaluer la protection auditive individuelle des travailleur ", a ete mis sur pied en 2010, associant l'Ecole de technologie superieure (ETS) et l'Institut de recherche Robert-Sauve en sante et en securite du travail (IRSST). S'inscrivant dans ce programme de recherche, le present travail de doctorat s'interesse specifiquement a la protection auditive au moyen de protecteurs auditifs " passifs " de type coquille, dont l'usage presente trois problematiques specifiques presentees dans les paragraphes suivants. La premiere problematique specifique concerne l'inconfort cause par exemple par la pression statique induite par la force de serrage de l'arceau, qui peut reduire le temps de port recommande pour limiter l'exposition au bruit. Il convient alors de pouvoir donner a l'utilisateur un protecteur confortable, adapte a son environnement de travail et a son activite. La seconde problematique specifique est l'evaluation de la protection reelle apportee par le protecteur. La methode des seuils auditifs REAT (Real Ear Attenuation Threshold) aussi vu comme un "golden standard" est utilise pour quantifier la reduction du bruit mais surestime generalement la performance des protecteurs. Les techniques de mesure terrains, telles que la F-MIRE (Field Measurement in Real Ear) peuvent etre a l'avenir de meilleurs outils pour evaluer l'attenuation individuelle. Si ces techniques existent pour des bouchons d'oreilles, elles doivent etre adaptees et ameliorees pour le cas des coquilles, en determinant l'emplacement optimal des capteurs acoustiques et les facteurs de compensation individuels qui lient la mesure microphonique a la mesure qui aurait ete prise au tympan. La troisieme problematique specifique est l'optimisation de l'attenuation des coquilles pour les adapter a l'individu et a son environnement de travail. En effet, le design des coquilles est generalement base sur des concepts empiriques et des methodes essais/erreurs sur des prototypes. La piste des outils predictifs a ete tres peu etudiee jusqu'a present et meriterait d'etre approfondie. L'utilisation du prototypage virtuel, permettrait a la fois d'optimiser le design avant production, d'accelerer la phase de developpement produit et d'en reduire les couts. L'objectif general de cette these est de repondre a ces differentes problematiques par le developpement d'un modele de l'attenuation sonore d'un protecteur auditif de type coquille. A cause de la complexite de la geometrie de ces protecteurs, la methode principale de modelisation retenue a priori est la methode des elements finis (FEM). Pour atteindre cet objectif general, trois objectifs specifiques ont ete etablis et sont presentes dans les trois paragraphes suivants. (Abstract shortened by ProQuest.).

Cartographie T

NASA Astrophysics Data System (ADS)

Cote, Jean-Charles

Les cartographies T1 par séquences d'échos stimulés et Look- Locker sont les plus communément utilisées pour mesurer les temps de relaxation T 1 en imagerie par résonance magnétique (IRM). Elles ont des performances d'usage clinique, ne prenant que quelques minutes pour produire une carte des valeurs de T1. Ces séquences demeurent cependant très sensibles à la précision des pulses radiofréquences (RF) qui réorientent l'aimantation pour produire les signaux mesurés. Les pulses RF rectangulaires régulièrement utilisés en IRM produisent un basculement de l'aimantation directement proportionnel à l'intensité du champ magnétique B 1 produit par l'antenne émettrice. Les antennes cliniques ont des distributions de champs B1 qui fluctuent énormément. En exemple, l'antenne servant à produire des images de la tête possède un champ B1 qui est distribué dans son volume utile sur une plage allant de 0,5 à 1,2 relativement à son centre. Cette variation spatiale de B1 entraîne des erreurs systématiques sur les valeurs ajustées de T1 dépassant les 50%. Le développement d'un nouveau concept d'excitation RF à approche tangentielle ayant des propriétés adiabatiques pouvant remplacer les demi-passages adiabatiques (AHP) et son utilisation sous la forme d'un BIR-4-S2 (B1-Insensitive Rotation-4 AHP-Sequentialized 2 steps) dans les séquences de cartographie T1 a permis de réduire à moins de 10% les erreurs systématiques dans le cas mesuré par échos stimulés compensés et à moins de 5% pour le Look-Locker. Le BIR-4-S2 possède une imprécision sur l'angle de basculement de moins de 5° sur une plage relative allant de 0,75 à 1,75 autour d'un champ de référence B1 ref, pour un choix de basculement sur 360°. Et, contrairement aux pulses adiabatiques, il demeure un pulse RF tridimentionnel (3D) à faible puissance pouvant être utilisé à répétition cliniquement sans risque d'échauffement dangereux pour les patients. La séquence d'échos stimulés compensés dont nous avons parlé ci-haut utilise un autre de nos développements: la compensation. Le signal produit par une séquence traditionnelle d'échos stimulés tend vers zéro en suivant la relaxation T1 dans le temps. Parfois ceci cause des problèmes lorsque le signal des derniers échos commence à être influencé par le bruit. La compensation a pour effet de modifier la décroissance exponentielle du signal. Ce changement s'opère en tenant compte de la relaxation T1 lors du calcul des angles de basculement nécessaire à la séquence. La compensation transfère une partie de la demande du volume de signal des premiers échos vers les derniers. On peut compenser entièrement et ainsi programmer une séquence qui produira des signaux égaux entre tous les échos ou compenser partiellement pour soutenir les signaux des derniers échos en conservant un maximum de signal total.

Epidémiologie des PFA et les performances du système de surveillance en Mauritanie de 2008 à 2012

PubMed Central

Doumtsop, Jean Gérard Tatou; Khalef, Ishagh; Diakite, Med Lemine Brahim; Boubker, Naouri

2014-01-01

Introduction La Commission Régionale de Certification de l'Eradication de la poliomyélite pour l'Afrique(CRCA) en session à Brazzaville du 8 au 10 octobre 2007 avait déclaré la Mauritanie « libérée de la poliomyélite ». Objectif Décrire l’épidémiologie des PFA (Paralysies flasques aigues) et évaluer les indicateurs de performance du système de surveillance pour la période de 2008 à 2012 ayant suivi cette déclaration. Méthodes Les données du service de surveillance épidémiologique ont été nettoyées et analysées à l'aide du logiciel Epi-infoversion 3.4.3 (CDC Atlanta). Résultats 319 cas de PFA ont été notifié soit une incidence moyenne de 4.61/100000 enfants de moins de 15 ans par an. La distribution des cas cumulés par mois montre une importante notification des cas PFA pendant la période de Février à Juillet et à la suite de l’épidémie de 2009 alors que l'incidence des cas confirmés a été plus importante entre Novembre et Février. L’âge moyen était de 4ans (E.T. ±4ans) et 77.4% avaient un âge = 5ans. 18 cas de PFA ont été confirmés poliovirus sauvage(PVS) dont 6 en 2009 et 12 en 2010 et tous d'importation. L’âge moyen était de 3.4 ans (E.T ±2.6 ans). 44,4% étaient des filles et 55.5% garçons. Cette proportion était proche de celle des PFA non polio (45.1% versus 54.9%). 61% avaient reçu au plus une dose de vaccin polio orale (VPO) pour les cas de PFA polio contre 7.4% pour les PFA non polio. Aucune discrimination de genre n'a été observé sur la population des PFA ayant reçu une dose au plus (ratio-sexe= 16/17=0.94). La fièvre était présente pour 90%des cas de PFA non polio contre 85% pour les cas PVS. Cette fièvre à progresser en 3 jours pour tous les cas de PVS et pour 82,7% des cas de PFA non polio. Le taux d'hospitalisation était de 13.6% pour les cas de PFA non polio contre 89% pour les PFA polio. Dans tous les deux groupes, les membres de prédilection étaient d'abord l'un des 2 membres inférieurs de façon alternative (46.8%), ensuite les deux membres inférieurs à la fois (22.2%). En troisième lieu, un membre supérieur et un membre inférieur de façon asymétrique (5.3%) et en quatrième lieu, tous les 4 membres (4.6%). Le diagnostic final des cas de PFA non polio n’était pas rapporté pendant toute la période de l’étude, cependant, 2 cas ont été classés compatible et un cas de paralysie associée à la vaccination contre la polio a été rapporté en 2012 chez un enfant féminin de 3 ans ayant reçu sa première dose de VPO. En ce qui concerne les performances des indicateurs de la surveillance, 4 indicateurs n'ont pas atteint les performances escomptées: Le pourcentage des échantillons arrivés au laboratoire national moins de 3 jours après les prélèvements est resté en deçà des objectifs, variant entre 40% et 70%. Il en est de même des Districts de santé ayant notifies au moins un cas (50 à 68%). Le pourcentage des prélèvements dans lesquels un entérovirus non polio a été isolé a connu une évolution en dents de scie avec des valeurs de 0.0% en 2008 et en 2010 et 1.9% en 2011. L'examen de suivi du60emejour n'a concerné que les cas dont l’échantillon était jugé inadéquat au laboratoire. Conclusion Les PFA qui ont été notifiés en Mauritanie de 2008 à 2012 présentent tableau clinique qui est classique, et sont notifiés avec un pic régulier en début des périodes de soudure (Mars-Juillet) suggérant l'hypothèse d'un lien écologique avec les changements de climat et de régime alimentaire. Les performances des indicateursde la surveillance des PFA sont à améliorer, notamment: 1) La compréhension des critères de jugement de la qualité des échantillons. 2) L'examen de laboratoire et l'interprétation des résultats. 3) La détermination du diagnostic final pour chaque cas de PFA non polio. 4) L'enregistrement des informations dans la base des données. PMID:25469198

Enhanced Aircraft Platform Availability Through Advanced Maintenance Concepts and Technologies (Amelioration de la disponibilite des plateformes d’aeronefs au moyen de concepts de maintenance et de technologies evolues)

DTIC Science & Technology

2011-06-01

des performances clés et modélisation de la disponibilité avion. • Concepts et technologies de gestion de la maintenance/ du soutien pour...l’utilisation des concepts de maintenance et des technologies avancées pour améliorer la disponibilité des aéronefs et réduire le coût du cycle de vie. L’équipe...aériennes. Dans la ligne du travail fourni par la commission AVT, un atelier

Age Rb/Sr de 1670 M.a. pour les mylonites de l'accident du Sassandra (Côte d'Ivoire) conséquence pour la datation des mouvements fini-éburnéens dans le craton ouest-africain

NASA Astrophysics Data System (ADS)

Caen-Vachette, M.; Tempier, P.; Camil, J.

An eight point Rb/Sr isochron determination on whole rocks yielded an age of 1670 M.a. for the mylonites from the Sassandra couloir of ductile deformation, which extends N-S. A similar age is proposed for the mylonite from a zone of parallel trend stretching NNW-SSE in the Reguibat dome (Mauritania). A correlation is suggested with the Guri fault of the Guayana shield in South America.

Specialists Meeting on Wing-with-Stores Flutter

DTIC Science & Technology

1975-04-01

I, 150 -z20L0 250 00 350o PYLON COMPONENT MODE (PITCH4-) GENER~ALISED INERTIA A C, 2-20 FIG. 13. AIRCRAFT BENDING MODE FREQUENCI ES , FOR SfORES ON...ldgbre ddportance tandis Gus J ’effet inverse eut o’uorv6 pour ] es sections au- .elth du rdscteur. Calcul et exp~rionce oont v,-. lw. accord at...nontrent que i’interaction du r’~acteur sur i.aile eat trbs locale ot d’intensitC6 s;.ffismaaent faible pour pouvoir 6trc n~glii4e dana lea calculs do

Benefits of Computer Assisted Translation to Information Managers and End-Users (L’Interet de la Traduction Assistee par Ordinateur Pour les Responsables de Centres d’Information et Pour Les Utilisateurs Finaux)

DTIC Science & Technology

1990-06-01

interlinear version which groups single source language/target language units sentence by sentence, or work on two windows with suurco and target text, or...d’autres systfmes 6ventuet Lenient. 00000 BibL lographie: R~pertoire des produits et services de traitement automa~tique de La Langue fran~aise...ptrocessors and it.. Conputers thai manioulate Hebrew /EngllSh. Araslc/Engss. IR-112 ArAbId/Fronhi. and Englisn/Ciihse characters are NP. 29: DP. Oct 8

Conference Proceedings on Visual Protection and Enhancement Held in Athens, Greece on 22-24 April 1985

DTIC Science & Technology

1985-12-01

mounted in one NVG barrel, which he styles an NVG head up display (HUD). A similar result could be obtained by using NVGs already equipped with beam...extrietcr. La perception du relief ne peut se faire par mise en eu de le stroscopie seuls los facteur corticaux da cotta parcaption 5O. utili’c4s...r6alit,ý op6rationnelle, contr616 at idantique pour tous los sujets. Pour ce faire , dos prises do vues ont 6t r~alis~es au magn~toscope lors do vol

Signature CERN-URSS

ScienceCinema

None

2017-12-09

Le DG W.Jentschke souhaite la bienvenue à l'assemblée et aux invités pour la signature du protocole entre le Cern et l'URSS qui est un événement important. C'est en 1955 que 55 visiteurs soviétiques ont visité le Cern pour la première fois. Le premier DG au Cern, F.Bloch, et Mons.Amaldi sont aussi présents. Tandis que le discours anglais de W.Jentschke est traduit en russe, le discours russe de Mons.Morozov est traduit en anglais.

AGARD/SMP Review Damage Tolerance for Engine Structures. 4. Reliability and Quality Assurance (Revue AGARD/SMP Tolerance Aux Dommages pour les Composants de Moteurs. 4 Fiabilite et Assurance Qualite)

DTIC Science & Technology

1991-12-01

lequel e110 as fonde n’est en pratique gubre virifi6 par 1’exp~rtence industriolle. Augmenter Is variabilit6 d’un procd diminue rarement lea cofits do...analyses pour sanctionnor los non- -conformitdo. augmentation des retouches et rebuts, Is tout gdndrant une digradation Importante des cycles ot...is a priori dangerous since the principle which It is based on Is scarcely verified in the industrial reality . The increase of the variability of a

Nuclear reactor containment structure with continuous ring tunnel at grade

DOEpatents

Seidensticker, Ralph W.; Knawa, Robert L.; Cerutti, Bernard C.; Snyder, Charles R.; Husen, William C.; Coyer, Robert G.

1977-01-01

A nuclear reactor containment structure which includes a reinforced concrete shell, a hemispherical top dome, a steel liner, and a reinforced-concrete base slab supporting the concrete shell is constructed with a substantial proportion thereof below grade in an excavation made in solid rock with the concrete poured in contact with the rock and also includes a continuous, hollow, reinforced-concrete ring tunnel surrounding the concrete shell with its top at grade level, with one wall integral with the reinforced concrete shell, and with at least the base of the ring tunnel poured in contact with the rock.

Active Acoustics using Bellhop-DRDC: Run Time Tests and Suggested Configurations for a Tracking Exercise in Shallow Scotian Waters

DTIC Science & Technology

2005-05-01

simulée d’essai pour obtenir les diagrammes de perte de transmission et de réverbération pour 18 éléments (une source, un réseau remorqué et 16 bouées...were recorded using a 1.5GHz Pentium 4 processor. The test results indicate that the Bellhop program runs fast enough to provide the required acoustic...was determined that the Bellhop program will be fast enough for these clients. Future Plans It is intended to integrate further enhancements that

Profil comparatif et évolutif des personnes infectées par le virus de l'immunodéficience humaine traitées aux antirétroviraux à Kinshasa, République Démocratique du Congo

PubMed Central

Koy, Tshingani; Mukumbi, Henri; Malandala, Ghislain Lubangi Muteba; Donnen, Philippe; Wilmet–Dramaix, Michèle

2014-01-01

Introduction A trithérapie (ARV) introduite en R.D.Congo en 1996, a permis l′amélioration substantielle de la qualité de vie des PVVIH et a réduit la morbimortalité liée au sida en R.D. Congo. L'objectif de cette étude est de présenter le profil épidémiologique comparatif, clinique, ainsi que l’évolution anthropométrique des PVVIH sous ARV à Kinshasa. Méthodes Etude de cohorte sur 438 PVVIH, de 18 ans et plus, suivies entre mai 2010 à 2011 à Amo Congo à Kinshasa. Une comparaison a été faite entre les patients suivis pendant un an et ceux perdus de vue. Le Chi carré de Mc Nemar et l'analyse de variance pour mesures répétées ont été appliqués pour étudier l’évolution. Résultats Près 12 mois de suivi, 11,4% de patients ont été perdus de vue. Parmi eux, on observait des proportions significativement plus élevées de personnes de niveau socioéconomique bas, d'indice de masse corporelle (IMC) bas, présentant de l'anorexie, des affections opportunistes. Les proportions de patients aux stades OMS 3 & 4 et naïfs étaient également significativement plus élevées et la durée sous ARV plus courte. Les gains moyens des paramètres anthropométriques au 12ème mois, étaient importants: de 3,6 [3,2 - 4,0] kg pour le poids, 1,8 (1,4 - 2,3) cm pour le périmètre abdominal, 0,9 (0,8 - 1,2) cm pour le périmètre brachial, 1,4 (1,2 - 1,5) kg/m2 pour l'IMC. La proportion de patients avec un IMC <18,5 kg/m2 a significativement plus baissé entre l'admission et le 12ème mois parmi les patients sans stomatite que parmi ceux avec stomatite. L'IMC moyen évoluait significativement différemment entre l'admission et le 12ème mois selon l’âge et la taille de ménage. Conclusion Les facteurs fragilisant la rétention des patients sous antirétroviraux et une évolution progressive de l’état nutritionnel ont été observés. PMID:25995784

Une nouvelle théorie de la cinétique des réactions radical-radical

NASA Astrophysics Data System (ADS)

Green, N. J. B.; Rickerby, A. G.

1999-01-01

Radical recombination reactions are of central importance in radiation chemistry. In general such reactions are slower than diffusion-controlled because of the radical spins. The rate constant is corrected by a multiplicative spin statistical factor, which represents the probability that the radicals encounter one another in a reactive state. However, this method does not account for the possibility that the reactivity of a pair may recover following an unreactive encounter, for example by spin relaxation or by a coherent evolution of the spin function. In this paper we show how the spin statistical factor can be corrected for the recovery of reactivity. The new theory covers a large range of mechanisms for the recovery of reactivity, and gives simple analytical results. Both steady-state and transient solutions are presented and the former are tested against experiment for the reaction between the hydrated electron and oxygen, and for the magnetic field effect on the rate constant of an elementary reaction. Les réactions de recombinaison entre deux radicaux libres ont une grande importance en chimie sous rayonnement. En général, du fait du spin des radicaux, de telles réactions sont moins rapides que celles qui sont contrôlées par la diffusion. Les constantes de vitesse sont corrigées par un facteur multiplicatif, le facteur statistique de spin, qui représente la probabilité pour que les radicaux se rencontrent, l'un avec l'autre, dans un état réactif. Cependant, cette méthode ne tient pas compte de la possibilité pour que la même paire se rencontre plusieurs fois en raison de rencontres non-réactives. Ensuite la réactivité de cette paire peut se rétablir par exemple par relaxation de spins, ou par évolution cohérente d'une superposition des états de spin. Dans cet article on démontre comment on peut corriger le facteur statistique de spin pour le rétablissement de la réactivité. La nouvelle théorie couvre un large domaine de mécanismes de rétablissement de la réactivité ; elle donne des résultats analytiques simples pour le facteur statistique modifié. On présente des solutions dans l'état stationnaire et des solutions transitoires; les premières sont testées pour la réaction entre l'électron hydraté et l'oxygène et également pour l'effet d'un champ magnétique sur la constante de vitesse d'une réaction élémentaire.

Facteurs associés à la non observance thérapeutique des sujets adultes infectés par le VIH sous antirétroviraux dans un hôpital de référence à Douala

PubMed Central

Essomba, Emmanuel Noel; Adiogo, Dieudonné; Koum, Danielle Christiane Kedy; Amang, Baudouin; Lehman, Leopold Gustave; Coppieters, Yves

2015-01-01

Introduction Le succès du traitement antirétroviral repose sur l'observance. Elle est nécessaire pour réduire la mortalité, diminuer le risque de résistance et restaurer l'immunité. Cette étude a pour but d'identifier et analyser les différents facteurs associés à la non observance thérapeutique des patients infectés par le VIH sous traitement antirétroviraux à l'hôpital de référence Laquintinie de Douala. Méthodes Il s'agit d'une étude transversale et analytique effectuée de mars à juin 2014. La non observance est mesurée à travers les déclarations du patient et sur consultation des registres de renouvellement des ordonnances. Etaient non observant, ceux ayant consommé moins de 95% de médicaments et ceux ne s’étant pas présentés pour le renouvellement de l'ordonnance. L'analyse bivariée et le modèle de régression logistique ont été utilisés pour la détermination des facteurs associés à la non observance. Résultats Au total, 524 patients ont été enrôlés dans l’étude;l’âge moyen était de 43,0 ± 10,7 ans et le sexe ratio H/F de 0,54. De ces patients, 49,0% étaient non observant, majoritairement des femmes (61,9%). Les principales raisons avancées de la non observance sont: l'oubli (32,9%), la rupture de médicaments (14,0%), les occupations (12,8%). Les personnes veuves(IC 95% OR= 1,31-5,22, p= 0,006), la consommation des excitants (IC 95%, OR= 2,30-6,90, p= 0,0001) et la présence d'infection opportuniste (IC 95%, OR= 1,41-17,54, p= 0,01) ont fortement été associés à la non observance. Conclusion Le taux d'observance était faible, lié à plusieurs facteurs. Des mesures sont nécessaires pour résoudre ce problème, y compris des stratégies tendant à l'amélioration du soutien psycho-social, et la limitation des ruptures de stock de médicaments. La recherche qualitative est souhaitée pour comprendre les raisons de la non observance afin de mettre au point des interventions fondées sur des données probantes. PMID:26301016

Diagnostic et prise en charge du psoriasis

PubMed Central

Kim, Whan B.; Jerome, Dana; Yeung, Jensen

2017-01-01

Résumé Objectif Présenter aux cliniciens en soins primaires un aperçu pratique et à jour du diagnostic et de la prise en charge du psoriasis. Sources des données Une recension a été effectuée dans les bases de données de PubMed, MEDLINE, EMBASE et Cochrane pour trouver des méta-analyses, des études randomisées contrôlées, des revues systématiques et des études observationnelles pertinentes portant sur le diagnostic et la prise en charge du psoriasis. Message principal Le psoriasis est une maladie inflammatoire chronique et multisystémique qui affecte principalement la peau et les articulations. En plus des dimensions physiques de la maladie, le psoriasis a des répercussions émotionnelles et psychosociales considérables sur les patients, et nuit au fonctionnement social et aux relations interpersonnelles. En tant que maladie inflammatoire systémique, le psoriasis est associé à de multiples comorbidités, dont les maladies cardiovasculaires et les cancers. Le diagnostic est principalement d’ordre clinique et une biopsie de la peau est rarement nécessaire. Selon la sévérité de la maladie, un traitement approprié peut être amorcé. Pour les cas de légers à modérés, le traitement de première intention comporte des thérapies topiques, dont les corticostéroïdes, les analogues de la vitamine D3 et des produits combinés. Ces traitements topiques sont efficaces et peuvent être initiés et prescrits en toute sécurité par des médecins de soins primaires. Les patients dont les symptômes sont plus graves et réfractaires pourraient devoir être envoyés en consultation auprès d’un dermatologue pour une évaluation plus approfondie et une thérapie systémique. Conclusion De nombreux patients atteints de psoriasis consultent leur médecin de soins primaires pour une évaluation initiale et pour recevoir un traitement. La reconnaissance du psoriasis, de même que des comorbidités médicales et psychiatriques qui lui sont associées, faciliterait un diagnostic en temps opportun et une prise en charge appropriée au moyen de traitements topiques sûrs et efficaces, et par d’autres interventions médicales et psychologiques au besoin. Il pourrait être nécessaire de demander une consultation en dermatologie pour les cas plus graves et réfractaires aux fins d’une évaluation plus approfondie et, possiblement, d’une thérapie systémique.

Developpement d'outils quantitatifs pour le suivi par imagerie TEP/TDM de la reponse a la chimiotherapie et de sa toxicite

NASA Astrophysics Data System (ADS)

Croteau, Etienne

L'objectif de ce projet de doctorat est de developper des outils quantitatifs pour le suivi des traitements de chimiotherapie pour le cancer du sein et de leurs effets cardiotoxiques a l'aide de l'imagerie TEP dynamique. L'analyse cinetique en TEP dynamique permet l'evaluation de parametres biologiques in vivo. Cette analyse peut etre utilise pour caracteriser la reponse tumorale a la chimiotherapie et les effets secondaires nefastes qui peuvent en resulter. Le premier article de cette these decrit la mise au point des techniques d'analyse cinetique qui utilisent la fonction d'entree d'un radiotraceur derive de l'image dynamique. Des corrections de contamination radioactive externe (epanchement) et de l'effet de volume partiel ont ete necessaires pour standardiser l'analyse cinetique et la rendre quantitative. Le deuxieme article porte sur l'evaluation d'un nouveau radiotraceur myocardique. Le 11C-acetoacetate, un nouveau radiotraceur base sur un corps cetonique, a ete compare au 11C-acetate, couramment utilise en imagerie cardiaque TEP. L'utilisation de 3H-acetate et 14C-acetoacetate ont permis d'elucider la cinetique de ces traceurs depuis la fonction d'entree et la captation par les mitochondries cardiaques qui reflete la consommation en oxygene, jusqu'a la liberation de leurs principaux metabolites reciproques (3H20 et 14CO2). Le troisieme et dernier article de cette these presente l'integration d'un modele qui evalue la reserve cardiaque de perfusion et de consommation en oxygene. Un modele de cardiomyopathie a ete etabli a l'aide d'un agent chimiotherapeutique contre le cancer du sein, la doxorubicine, reconnu comme etant cardiotoxique. Un protocole de repos/effort a permis d'evaluer la capacite d'augmentation de perfusion et de consommation en oxygene par le coeur. La demonstration d'une reserve cardiaque reduite caracterise la cardiotoxicite. La derniere contribution de cette these porte sur la mise au point de methodes peu invasives pour mesurer la fonction d'entree en modele animal avec l'utilisation de l'artere caudale et un compteur microvolumetrique, la bi-modalite TEP/IRM dynamique avec le Gd-DTPA et l'etablissement d'un modele d'evaluation simultane de cardiotoxicite et reponse tumorale chez la souris. Le developpement d'outils d'analyse TEP dans l'evaluation de la cardiotoxicite lors de traitements du canter du sein permet de mieux comprendre la relation entre les dommages mitochondriaux et la diminution de la fraction d'ejection. Mots cles : Tomographie d'emission par positrons (TEP), analyses cinetiques, IIC-acetate, 11Cacetoacetate, cardiotoxicite.