Methodologies for launcher-payload coupled dynamic analysis

NASA Astrophysics Data System (ADS)

Fransen, S. H. J. A.

2012-06-01

An important step in the design and verification process of spacecraft structures is the coupled dynamic analysis with the launch vehicle in the low-frequency domain, also referred to as coupled loads analysis (CLA). The objective of such analyses is the computation of the dynamic environment of the spacecraft (payload) in terms of interface accelerations, interface forces, center of gravity (CoG) accelerations as well as the internal state of stress. In order to perform an efficient, fast and accurate launcher-payload coupled dynamic analysis, various methodologies have been applied and developed. The methods are related to substructuring techniques, data recovery techniques, the effects of prestress and fluids and time integration problems. The aim of this paper was to give an overview of these methodologies and to show why, how and where these techniques can be used in the process of launcher-payload coupled dynamic analysis. In addition, it will be shown how these methodologies fit together in a library of procedures which can be used with the MSC.Nastran™ solution sequences.

Rating of Dynamic Coefficient for Simple Beam Bridge Design on High-Speed Railways

NASA Astrophysics Data System (ADS)

Diachenko, Leonid; Benin, Andrey; Smirnov, Vladimir; Diachenko, Anastasia

2018-06-01

The aim of the work is to improve the methodology for the dynamic computation of simple beam spans during the impact of high-speed trains. Mathematical simulation utilizing numerical and analytical methods of structural mechanics is used in the research. The article analyses parameters of the effect of high-speed trains on simple beam spanning bridge structures and suggests a technique of determining of the dynamic index to the live load. Reliability of the proposed methodology is confirmed by results of numerical simulation of high-speed train passage over spans with different speeds. The proposed algorithm of dynamic computation is based on a connection between maximum acceleration of the span in the resonance mode of vibrations and the main factors of stress-strain state. The methodology allows determining maximum and also minimum values of the main efforts in the construction that makes possible to perform endurance tests. It is noted that dynamic additions for the components of the stress-strain state (bending moments, transverse force and vertical deflections) are different. This condition determines the necessity for differentiated approach to evaluation of dynamic coefficients performing design verification of I and II groups of limiting state. The practical importance: the methodology of determining the dynamic coefficients allows making dynamic calculation and determining the main efforts in split beam spans without numerical simulation and direct dynamic analysis that significantly reduces the labour costs for design.

Mechatronics by Analogy and Application to Legged Locomotion

NASA Astrophysics Data System (ADS)

Ragusila, Victor

A new design methodology for mechatronic systems, dubbed as Mechatronics by Analogy (MbA), is introduced and applied to designing a leg mechanism. The new methodology argues that by establishing a similarity relation between a complex system and a number of simpler models it is possible to design the former using the analysis and synthesis means developed for the latter. The methodology provides a framework for concurrent engineering of complex systems while maintaining the transparency of the system behaviour through making formal analogies between the system and those with more tractable dynamics. The application of the MbA methodology to the design of a monopod robot leg, called the Linkage Leg, is also studied. A series of simulations show that the dynamic behaviour of the Linkage Leg is similar to that of a combination of a double pendulum and a spring-loaded inverted pendulum, based on which the system kinematic, dynamic, and control parameters can be designed concurrently. The first stage of Mechatronics by Analogy is a method of extracting significant features of system dynamics through simpler models. The goal is to determine a set of simpler mechanisms with similar dynamic behaviour to that of the original system in various phases of its motion. A modular bond-graph representation of the system is determined, and subsequently simplified using two simplification algorithms. The first algorithm determines the relevant dynamic elements of the system for each phase of motion, and the second algorithm finds the simple mechanism described by the remaining dynamic elements. In addition to greatly simplifying the controller for the system, using simpler mechanisms with similar behaviour provides a greater insight into the dynamics of the system. This is seen in the second stage of the new methodology, which concurrently optimizes the simpler mechanisms together with a control system based on their dynamics. Once the optimal configuration of the simpler system is determined, the original mechanism is optimized such that its dynamic behaviour is analogous. It is shown that, if this analogy is achieved, the control system designed based on the simpler mechanisms can be directly implemented to the more complex system, and their dynamic behaviours are close enough for the system performance to be effectively the same. Finally it is shown that, for the employed objective of fast legged locomotion, the proposed methodology achieves a better design than Reduction-by-Feedback, a competing methodology that uses control layers to simplify the dynamics of the system.

Moving alcohol prevention research forward-Part II: new directions grounded in community-based system dynamics modeling.

PubMed

Apostolopoulos, Yorghos; Lemke, Michael K; Barry, Adam E; Lich, Kristen Hassmiller

2018-02-01

Given the complexity of factors contributing to alcohol misuse, appropriate epistemologies and methodologies are needed to understand and intervene meaningfully. We aimed to (1) provide an overview of computational modeling methodologies, with an emphasis on system dynamics modeling; (2) explain how community-based system dynamics modeling can forge new directions in alcohol prevention research; and (3) present a primer on how to build alcohol misuse simulation models using system dynamics modeling, with an emphasis on stakeholder involvement, data sources and model validation. Throughout, we use alcohol misuse among college students in the United States as a heuristic example for demonstrating these methodologies. System dynamics modeling employs a top-down aggregate approach to understanding dynamically complex problems. Its three foundational properties-stocks, flows and feedbacks-capture non-linearity, time-delayed effects and other system characteristics. As a methodological choice, system dynamics modeling is amenable to participatory approaches; in particular, community-based system dynamics modeling has been used to build impactful models for addressing dynamically complex problems. The process of community-based system dynamics modeling consists of numerous stages: (1) creating model boundary charts, behavior-over-time-graphs and preliminary system dynamics models using group model-building techniques; (2) model formulation; (3) model calibration; (4) model testing and validation; and (5) model simulation using learning-laboratory techniques. Community-based system dynamics modeling can provide powerful tools for policy and intervention decisions that can result ultimately in sustainable changes in research and action in alcohol misuse prevention. © 2017 Society for the Study of Addiction.

Passenger rail vehicle safety assessment methodology. Volume II, Detailed analyses and simulation results.

DOT National Transportation Integrated Search

2000-04-01

This report presents detailed analytic tools and results on dynamic response which are used to develop the safe dynamic performance limits of commuter passenger vehicles. The methodology consists of determining the critical parameters and characteris...

Extended cooperative control synthesis

NASA Technical Reports Server (NTRS)

Davidson, John B.; Schmidt, David K.

1994-01-01

This paper reports on research for extending the Cooperative Control Synthesis methodology to include a more accurate modeling of the pilot's controller dynamics. Cooperative Control Synthesis (CCS) is a methodology that addresses the problem of how to design control laws for piloted, high-order, multivariate systems and/or non-conventional dynamic configurations in the absence of flying qualities specifications. This is accomplished by emphasizing the parallel structure inherent in any pilot-controlled, augmented vehicle. The original CCS methodology is extended to include the Modified Optimal Control Model (MOCM), which is based upon the optimal control model of the human operator developed by Kleinman, Baron, and Levison in 1970. This model provides a modeling of the pilot's compensation dynamics that is more accurate than the simplified pilot dynamic representation currently in the CCS methodology. Inclusion of the MOCM into the CCS also enables the modeling of pilot-observation perception thresholds and pilot-observation attention allocation affects. This Extended Cooperative Control Synthesis (ECCS) allows for the direct calculation of pilot and system open- and closed-loop transfer functions in pole/zero form and is readily implemented in current software capable of analysis and design for dynamic systems. Example results based upon synthesizing an augmentation control law for an acceleration command system in a compensatory tracking task using the ECCS are compared with a similar synthesis performed by using the original CCS methodology. The ECCS is shown to provide augmentation control laws that yield more favorable, predicted closed-loop flying qualities and tracking performance than those synthesized using the original CCS methodology.

Nonlinear maneuver autopilot for the F-15 aircraft

NASA Technical Reports Server (NTRS)

Menon, P. K. A.; Badgett, M. E.; Walker, R. A.

1989-01-01

A methodology is described for the development of flight test trajectory control laws based on singular perturbation methodology and nonlinear dynamic modeling. The control design methodology is applied to a detailed nonlinear six degree-of-freedom simulation of the F-15 and results for a level accelerations, pushover/pullup maneuver, zoom and pushover maneuver, excess thrust windup turn, constant thrust windup turn, and a constant dynamic pressure/constant load factor trajectory are presented.

Assessing Similarity Among Individual Tumor Size Lesion Dynamics: The CICIL Methodology

PubMed Central

Girard, Pascal; Ioannou, Konstantinos; Klinkhardt, Ute; Munafo, Alain

2018-01-01

Mathematical models of tumor dynamics generally omit information on individual target lesions (iTLs), and consider the most important variable to be the sum of tumor sizes (TS). However, differences in lesion dynamics might be predictive of tumor progression. To exploit this information, we have developed a novel and flexible approach for the non‐parametric analysis of iTLs, which integrates knowledge from signal processing and machine learning. We called this new methodology ClassIfication Clustering of Individual Lesions (CICIL). We used CICIL to assess similarities among the TS dynamics of 3,223 iTLs measured in 1,056 patients with metastatic colorectal cancer treated with cetuximab combined with irinotecan, in two phase II studies. We mainly observed similar dynamics among lesions within the same tumor site classification. In contrast, lesions in anatomic locations with different features showed different dynamics in about 35% of patients. The CICIL methodology has also been implemented in a user‐friendly and efficient Java‐based framework. PMID:29388396

Progression of 3D Protein Structure and Dynamics Measurements

NASA Astrophysics Data System (ADS)

Sato-Tomita, Ayana; Sekiguchi, Hiroshi; Sasaki, Yuji C.

2018-06-01

New measurement methodologies have begun to be proposed with the recent progress in the life sciences. Here, we introduce two new methodologies, X-ray fluorescence holography for protein structural analysis and diffracted X-ray tracking (DXT), to observe the dynamic behaviors of individual single molecules.

Verification of nonlinear dynamic structural test results by combined image processing and acoustic analysis

NASA Astrophysics Data System (ADS)

Tene, Yair; Tene, Noam; Tene, G.

1993-08-01

An interactive data fusion methodology of video, audio, and nonlinear structural dynamic analysis for potential application in forensic engineering is presented. The methodology was developed and successfully demonstrated in the analysis of heavy transportable bridge collapse during preparation for testing. Multiple bridge elements failures were identified after the collapse, including fracture, cracks and rupture of high performance structural materials. Videotape recording by hand held camcorder was the only source of information about the collapse sequence. The interactive data fusion methodology resulted in extracting relevant information form the videotape and from dynamic nonlinear structural analysis, leading to full account of the sequence of events during the bridge collapse.

Shuttle payload bay dynamic environments: Summary and conclusion report for STS flights 1-5 and 9

NASA Technical Reports Server (NTRS)

Oconnell, M.; Garba, J.; Kern, D.

1984-01-01

The vibration, acoustic and low frequency loads data from the first 5 shuttle flights are presented. The engineering analysis of that data is also presented. Vibroacoustic data from STS-9 are also presented because they represent the only data taken on a large payload. Payload dynamic environment predictions developed by the participation of various NASA and industrial centers are presented along with a comparison of analytical loads methodology predictions with flight data, including a brief description of the methodologies employed in developing those predictions for payloads. The review of prediction methodologies illustrates how different centers have approached the problems of developing shuttle dynamic environmental predictions and criteria. Ongoing research activities related to the shuttle dynamic environments are also described. Analytical software recently developed for the prediction of payload acoustic and vibration environments are also described.

Effects of Special Use Airspace on Economic Benefits of Direct Flights

NASA Technical Reports Server (NTRS)

Datta, Koushik; Barrington, Craig; Foster, John D. (Technical Monitor)

1996-01-01

A methodology for estimating the economic effects of Special Use Airspace (SUA) on direct route flights is presented in this paper. The methodology is based on evaluating operating costs of aircraft and analyzing the different ground-track distances traveled by flights under different air traffic scenarios. Using this methodology the following objectives are evaluated: optimistic bias of studies that assume accessible SUAs the maximum economic benefit of dynamic use of SUAs and the marginal economic benefit of the dynamic use of individual SUAs.

Optimized planning methodologies of ASON implementation

NASA Astrophysics Data System (ADS)

Zhou, Michael M.; Tamil, Lakshman S.

2005-02-01

Advanced network planning concerns effective network-resource allocation for dynamic and open business environment. Planning methodologies of ASON implementation based on qualitative analysis and mathematical modeling are presented in this paper. The methodology includes method of rationalizing technology and architecture, building network and nodal models, and developing dynamic programming for multi-period deployment. The multi-layered nodal architecture proposed here can accommodate various nodal configurations for a multi-plane optical network and the network modeling presented here computes the required network elements for optimizing resource allocation.

An overview of the dynamic calibration of piezoelectric pressure transducers

NASA Astrophysics Data System (ADS)

Theodoro, F. R. F.; Reis, M. L. C. C.; d’ Souto, C.

2018-03-01

Dynamic calibration is a research area that is still under development and is of great interest to aerospace and automotive industries. This study discusses some concepts regarding dynamic measurements of pressure quantities and presents an overview of dynamic calibration of pressure transducers. Studies conducted by the Institute of Aeronautics and Space focusing on research regarding piezoelectric pressure transducer calibration in shock tube are presented. We employed the Guide to the Expression of Uncertainty and a Monte Carlo Method in the methodology. The results show that both device and methodology employed are adequate to calibrate the piezoelectric sensor.

Dynamic but Prosaic: A Methodology for Studying E-Learning Environments

ERIC Educational Resources Information Center

Whitworth, Andrew

2006-01-01

This paper develops a critical methodology which could be applied to the study and use of e-learning environments. The foundations are, first, an ontological appreciation of environments as multiple, dynamic and interactive: this is based on the environmental theories of Vladimir Vernadsky. The next step is then into epistemology, and here use is…

Beyond "on" or "with": Questioning Power Dynamics and Knowledge Production in "Child-Oriented" Research Methodology

ERIC Educational Resources Information Center

Hunleth, Jean

2011-01-01

By taking a reflexive approach to research methodology, this article contributes to discussions on power dynamics and knowledge production in the social studies of children. The author describes and analyzes three research methods that she used with children--drawing, child-led tape-recording and focus group discussions. These methods were carried…

Dynamic determination of kinetic parameters and computer simulation of growth of Clostridium perfringens in cooked beef

USDA-ARS?s Scientific Manuscript database

The objective of this research was to develop a new one-step methodology that uses a dynamic approach to directly construct a tertiary model for prediction of the growth of C. perfringens in cooked beef. This methodology was based on numerical analysis and optimization of both primary and secondary...

Team Dynamics. Essays in the Sociology and Social Psychology of Sport Including Methodological and Epistemological Issues.

ERIC Educational Resources Information Center

Lenk, Hans

This document contains nine essays on the sociology and social psychology of team dynamics, including methodological and epistemological issues involved in such study. Essay titles are: (1) Conflict and Achievement in Top Athletic Teams--Sociometric Structures of Racing Eight Oar Crews; (2) Top Performance Despite Internal Conflict--An Antithesis…

New methodology for fast prediction of wheel wear evolution

NASA Astrophysics Data System (ADS)

Apezetxea, I. S.; Perez, X.; Casanueva, C.; Alonso, A.

2017-07-01

In railway applications wear prediction in the wheel-rail interface is a fundamental matter in order to study problems such as wheel lifespan and the evolution of vehicle dynamic characteristic with time. However, one of the principal drawbacks of the existing methodologies for calculating the wear evolution is the computational cost. This paper proposes a new wear prediction methodology with a reduced computational cost. This methodology is based on two main steps: the first one is the substitution of the calculations over the whole network by the calculation of the contact conditions in certain characteristic point from whose result the wheel wear evolution can be inferred. The second one is the substitution of the dynamic calculation (time integration calculations) by the quasi-static calculation (the solution of the quasi-static situation of a vehicle at a certain point which is the same that neglecting the acceleration terms in the dynamic equations). These simplifications allow a significant reduction of computational cost to be obtained while maintaining an acceptable level of accuracy (error order of 5-10%). Several case studies are analysed along the paper with the objective of assessing the proposed methodology. The results obtained in the case studies allow concluding that the proposed methodology is valid for an arbitrary vehicle running through an arbitrary track layout.

Enhanced High Performance Power Compensation Methodology by IPFC Using PIGBT-IDVR

PubMed Central

Arumugom, Subramanian; Rajaram, Marimuthu

2015-01-01

Currently, power systems are involuntarily controlled without high speed control and are frequently initiated, therefore resulting in a slow process when compared with static electronic devices. Among various power interruptions in power supply systems, voltage dips play a central role in causing disruption. The dynamic voltage restorer (DVR) is a process based on voltage control that compensates for line transients in the distributed system. To overcome these issues and to achieve a higher speed, a new methodology called the Parallel IGBT-Based Interline Dynamic Voltage Restorer (PIGBT-IDVR) method has been proposed, which mainly spotlights the dynamic processing of energy reloads in common dc-linked energy storage with less adaptive transition. The interline power flow controller (IPFC) scheme has been employed to manage the power transmission between the lines and the restorer method for controlling the reactive power in the individual lines. By employing the proposed methodology, the failure of a distributed system has been avoided and provides better performance than the existing methodologies. PMID:26613101

Wind Tunnel to Atmospheric Mapping for Static Aeroelastic Scaling

NASA Technical Reports Server (NTRS)

Heeg, Jennifer; Spain, Charles V.; Rivera, J. A.

2004-01-01

Wind tunnel to Atmospheric Mapping (WAM) is a methodology for scaling and testing a static aeroelastic wind tunnel model. The WAM procedure employs scaling laws to define a wind tunnel model and wind tunnel test points such that the static aeroelastic flight test data and wind tunnel data will be correlated throughout the test envelopes. This methodology extends the notion that a single test condition - combination of Mach number and dynamic pressure - can be matched by wind tunnel data. The primary requirements for affecting this extension are matching flight Mach numbers, maintaining a constant dynamic pressure scale factor and setting the dynamic pressure scale factor in accordance with the stiffness scale factor. The scaling is enabled by capabilities of the NASA Langley Transonic Dynamics Tunnel (TDT) and by relaxation of scaling requirements present in the dynamic problem that are not critical to the static aeroelastic problem. The methodology is exercised in two example scaling problems: an arbitrarily scaled wing and a practical application to the scaling of the Active Aeroelastic Wing flight vehicle for testing in the TDT.

Dynamic Bayesian wavelet transform: New methodology for extraction of repetitive transients

NASA Astrophysics Data System (ADS)

Wang, Dong; Tsui, Kwok-Leung

2017-05-01

Thanks to some recent research works, dynamic Bayesian wavelet transform as new methodology for extraction of repetitive transients is proposed in this short communication to reveal fault signatures hidden in rotating machine. The main idea of the dynamic Bayesian wavelet transform is to iteratively estimate posterior parameters of wavelet transform via artificial observations and dynamic Bayesian inference. First, a prior wavelet parameter distribution can be established by one of many fast detection algorithms, such as the fast kurtogram, the improved kurtogram, the enhanced kurtogram, the sparsogram, the infogram, continuous wavelet transform, discrete wavelet transform, wavelet packets, multiwavelets, empirical wavelet transform, empirical mode decomposition, local mean decomposition, etc.. Second, artificial observations can be constructed based on one of many metrics, such as kurtosis, the sparsity measurement, entropy, approximate entropy, the smoothness index, a synthesized criterion, etc., which are able to quantify repetitive transients. Finally, given artificial observations, the prior wavelet parameter distribution can be posteriorly updated over iterations by using dynamic Bayesian inference. More importantly, the proposed new methodology can be extended to establish the optimal parameters required by many other signal processing methods for extraction of repetitive transients.

System Dynamics Modeling for Proactive Intelligence

DTIC Science & Technology

2010-01-01

5  4. Modeling Resources as Part of an Integrated Multi- Methodology System .................. 16  5. Formalizing Pro-Active...Observable Data With and Without Simulation Analysis ............................... 15  Figure 13. Summary of Probe Methodology and Results...Strategy ............................................................................. 22  Figure 22. Overview of Methodology

Substructuring of multibody systems for numerical transfer path analysis in internal combustion engines

NASA Astrophysics Data System (ADS)

Acri, Antonio; Offner, Guenter; Nijman, Eugene; Rejlek, Jan

2016-10-01

Noise legislations and the increasing customer demands determine the Noise Vibration and Harshness (NVH) development of modern commercial vehicles. In order to meet the stringent legislative requirements for the vehicle noise emission, exact knowledge of all vehicle noise sources and their acoustic behavior is required. Transfer path analysis (TPA) is a fairly well established technique for estimating and ranking individual low-frequency noise or vibration contributions via the different transmission paths. Transmission paths from different sources to target points of interest and their contributions can be analyzed by applying TPA. This technique is applied on test measurements, which can only be available on prototypes, at the end of the designing process. In order to overcome the limits of TPA, a numerical transfer path analysis methodology based on the substructuring of a multibody system is proposed in this paper. Being based on numerical simulation, this methodology can be performed starting from the first steps of the designing process. The main target of the proposed methodology is to get information of noise sources contributions of a dynamic system considering the possibility to have multiple forces contemporary acting on the system. The contributions of these forces are investigated with particular focus on distribute or moving forces. In this paper, the mathematical basics of the proposed methodology and its advantages in comparison with TPA will be discussed. Then, a dynamic system is investigated with a combination of two methods. Being based on the dynamic substructuring (DS) of the investigated model, the methodology proposed requires the evaluation of the contact forces at interfaces, which are computed with a flexible multi-body dynamic (FMBD) simulation. Then, the structure-borne noise paths are computed with the wave based method (WBM). As an example application a 4-cylinder engine is investigated and the proposed methodology is applied on the engine block. The aim is to get accurate and clear relationships between excitations and responses of the simulated dynamic system, analyzing the noise and vibrational sources inside a car engine, showing the main advantages of a numerical methodology.

NASA Handbook for Spacecraft Structural Dynamics Testing

NASA Technical Reports Server (NTRS)

Kern, Dennis L.; Scharton, Terry D.

2005-01-01

Recent advances in the area of structural dynamics and vibrations, in both methodology and capability, have the potential to make spacecraft system testing more effective from technical, cost, schedule, and hardware safety points of view. However, application of these advanced test methods varies widely among the NASA Centers and their contractors. Identification and refinement of the best of these test methodologies and implementation approaches has been an objective of efforts by the Jet Propulsion Laboratory on behalf of the NASA Office of the Chief Engineer. But to develop the most appropriate overall test program for a flight project from the selection of advanced methodologies, as well as conventional test methods, spacecraft project managers and their technical staffs will need overall guidance and technical rationale. Thus, the Chief Engineer's Office has recently tasked JPL to prepare a NASA Handbook for Spacecraft Structural Dynamics Testing. An outline of the proposed handbook, with a synopsis of each section, has been developed and is presented herein. Comments on the proposed handbook are solicited from the spacecraft structural dynamics testing community.

NASA Handbook for Spacecraft Structural Dynamics Testing

NASA Technical Reports Server (NTRS)

Kern, Dennis L.; Scharton, Terry D.

2004-01-01

Recent advances in the area of structural dynamics and vibrations, in both methodology and capability, have the potential to make spacecraft system testing more effective from technical, cost, schedule, and hardware safety points of view. However, application of these advanced test methods varies widely among the NASA Centers and their contractors. Identification and refinement of the best of these test methodologies and implementation approaches has been an objective of efforts by the Jet Propulsion Laboratory on behalf of the NASA Office of the Chief Engineer. But to develop the most appropriate overall test program for a flight project from the selection of advanced methodologies, as well as conventional test methods, spacecraft project managers and their technical staffs will need overall guidance and technical rationale. Thus, the Chief Engineer's Office has recently tasked JPL to prepare a NASA Handbook for Spacecraft Structural Dynamics Testing. An outline of the proposed handbook, with a synopsis of each section, has been developed and is presented herein. Comments on the proposed handbook is solicited from the spacecraft structural dynamics testing community.

Method and system for dynamic probabilistic risk assessment

NASA Technical Reports Server (NTRS)

Dugan, Joanne Bechta (Inventor); Xu, Hong (Inventor)

2013-01-01

The DEFT methodology, system and computer readable medium extends the applicability of the PRA (Probabilistic Risk Assessment) methodology to computer-based systems, by allowing DFT (Dynamic Fault Tree) nodes as pivot nodes in the Event Tree (ET) model. DEFT includes a mathematical model and solution algorithm, supports all common PRA analysis functions and cutsets. Additional capabilities enabled by the DFT include modularization, phased mission analysis, sequence dependencies, and imperfect coverage.

Methodologies for Verification and Validation of Space Launch System (SLS) Structural Dynamic Models: Appendices

NASA Technical Reports Server (NTRS)

Coppolino, Robert N.

2018-01-01

Verification and validation (V&V) is a highly challenging undertaking for SLS structural dynamics models due to the magnitude and complexity of SLS subassemblies and subassemblies. Responses to challenges associated with V&V of Space Launch System (SLS) structural dynamics models are presented in Volume I of this paper. Four methodologies addressing specific requirements for V&V are discussed. (1) Residual Mode Augmentation (RMA). (2) Modified Guyan Reduction (MGR) and Harmonic Reduction (HR, introduced in 1976). (3) Mode Consolidation (MC). Finally, (4) Experimental Mode Verification (EMV). This document contains the appendices to Volume I.

Soft tissue deformation modelling through neural dynamics-based reaction-diffusion mechanics.

PubMed

Zhang, Jinao; Zhong, Yongmin; Gu, Chengfan

2018-05-30

Soft tissue deformation modelling forms the basis of development of surgical simulation, surgical planning and robotic-assisted minimally invasive surgery. This paper presents a new methodology for modelling of soft tissue deformation based on reaction-diffusion mechanics via neural dynamics. The potential energy stored in soft tissues due to a mechanical load to deform tissues away from their rest state is treated as the equivalent transmembrane potential energy, and it is distributed in the tissue masses in the manner of reaction-diffusion propagation of nonlinear electrical waves. The reaction-diffusion propagation of mechanical potential energy and nonrigid mechanics of motion are combined to model soft tissue deformation and its dynamics, both of which are further formulated as the dynamics of cellular neural networks to achieve real-time computational performance. The proposed methodology is implemented with a haptic device for interactive soft tissue deformation with force feedback. Experimental results demonstrate that the proposed methodology exhibits nonlinear force-displacement relationship for nonlinear soft tissue deformation. Homogeneous, anisotropic and heterogeneous soft tissue material properties can be modelled through the inherent physical properties of mass points. Graphical abstract Soft tissue deformation modelling with haptic feedback via neural dynamics-based reaction-diffusion mechanics.

Transport composite fuselage technology: Impact dynamics and acoustic transmission

NASA Technical Reports Server (NTRS)

Jackson, A. C.; Balena, F. J.; Labarge, W. L.; Pei, G.; Pitman, W. A.; Wittlin, G.

1986-01-01

A program was performed to develop and demonstrate the impact dynamics and acoustic transmission technology for a composite fuselage which meets the design requirements of a 1990 large transport aircraft without substantial weight and cost penalties. The program developed the analytical methodology for the prediction of acoustic transmission behavior of advanced composite stiffened shell structures. The methodology predicted that the interior noise level in a composite fuselage due to turbulent boundary layer will be less than in a comparable aluminum fuselage. The verification of these analyses will be performed by NASA Langley Research Center using a composite fuselage shell fabricated by filament winding. The program also developed analytical methodology for the prediction of the impact dynamics behavior of lower fuselage structure constructed with composite materials. Development tests were performed to demonstrate that the composite structure designed to the same operating load requirement can have at least the same energy absorption capability as aluminum structure.

Multibody dynamic simulation of knee contact mechanics

PubMed Central

Bei, Yanhong; Fregly, Benjamin J.

2006-01-01

Multibody dynamic musculoskeletal models capable of predicting muscle forces and joint contact pressures simultaneously would be valuable for studying clinical issues related to knee joint degeneration and restoration. Current three-dimensional multi-body knee models are either quasi-static with deformable contact or dynamic with rigid contact. This study proposes a computationally efficient methodology for combining multibody dynamic simulation methods with a deformable contact knee model. The methodology requires preparation of the articular surface geometry, development of efficient methods to calculate distances between contact surfaces, implementation of an efficient contact solver that accounts for the unique characteristics of human joints, and specification of an application programming interface for integration with any multibody dynamic simulation environment. The current implementation accommodates natural or artificial tibiofemoral joint models, small or large strain contact models, and linear or nonlinear material models. Applications are presented for static analysis (via dynamic simulation) of a natural knee model created from MRI and CT data and dynamic simulation of an artificial knee model produced from manufacturer’s CAD data. Small and large strain natural knee static analyses required 1 min of CPU time and predicted similar contact conditions except for peak pressure, which was higher for the large strain model. Linear and nonlinear artificial knee dynamic simulations required 10 min of CPU time and predicted similar contact force and torque but different contact pressures, which were lower for the nonlinear model due to increased contact area. This methodology provides an important step toward the realization of dynamic musculoskeletal models that can predict in vivo knee joint motion and loading simultaneously. PMID:15564115

An Information Theoretic Investigation Of Complex Adaptive Supply Networks With Organizational Topologies

DTIC Science & Technology

2016-12-22

assumptions of behavior. This research proposes an information theoretic methodology to discover such complex network structures and dynamics while overcoming...the difficulties historically associated with their study. Indeed, this was the first application of an information theoretic methodology as a tool...1 Research Objectives and Questions..............................................................................2 Methodology

Methodology for Uncertainty Analysis of Dynamic Computational Toxicology Models

EPA Science Inventory

The task of quantifying the uncertainty in both parameter estimates and model predictions has become more important with the increased use of dynamic computational toxicology models by the EPA. Dynamic toxicological models include physiologically-based pharmacokinetic (PBPK) mode...

Rocket Engine Nozzle Side Load Transient Analysis Methodology: A Practical Approach

NASA Technical Reports Server (NTRS)

Shi, John J.

2005-01-01

During the development stage, in order to design/to size the rocket engine components and to reduce the risks, the local dynamic environments as well as dynamic interface loads must be defined. There are two kinds of dynamic environment, i.e. shock transients and steady-state random and sinusoidal vibration environments. Usually, the steady-state random and sinusoidal vibration environments are scalable, but the shock environments are not scalable. In other words, based on similarities only random vibration environments can be defined for a new engine. The methodology covered in this paper provides a way to predict the shock environments and the dynamic loads for new engine systems and new engine components in the early stage of new engine development or engine nozzle modifications.

Planning a dynamic kill

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abel, L.W.

1996-05-01

This article discusses the methodology, design philosophy, and guidelines for planning a dynamic-kill operation for a wild well. The topics covered are two methods of computer analysis for designing dynamic-kill requirements, the design process, determining the pumping spread, and the pitfalls that a designer faces in planning a dynamic kill.

Use of measurement theory for operationalization and quantification of psychological constructs in systems dynamics modelling

NASA Astrophysics Data System (ADS)

Fitkov-Norris, Elena; Yeghiazarian, Ara

2016-11-01

The analytical tools available to social scientists have traditionally been adapted from tools originally designed for analysis of natural science phenomena. This article discusses the applicability of systems dynamics - a qualitative based modelling approach, as a possible analysis and simulation tool that bridges the gap between social and natural sciences. After a brief overview of the systems dynamics modelling methodology, the advantages as well as limiting factors of systems dynamics to the potential applications in the field of social sciences and human interactions are discussed. The issues arise with regards to operationalization and quantification of latent constructs at the simulation building stage of the systems dynamics methodology and measurement theory is proposed as a ready and waiting solution to the problem of dynamic model calibration, with a view of improving simulation model reliability and validity and encouraging the development of standardised, modular system dynamics models that can be used in social science research.

Pressure-based high-order TVD methodology for dynamic stall control

NASA Astrophysics Data System (ADS)

Yang, H. Q.; Przekwas, A. J.

1992-01-01

The quantitative prediction of the dynamics of separating unsteady flows, such as dynamic stall, is of crucial importance. This six-month SBIR Phase 1 study has developed several new pressure-based methodologies for solving 3D Navier-Stokes equations in both stationary and moving (body-comforting) coordinates. The present pressure-based algorithm is equally efficient for low speed incompressible flows and high speed compressible flows. The discretization of convective terms by the presently developed high-order TVD schemes requires no artificial dissipation and can properly resolve the concentrated vortices in the wing-body with minimum numerical diffusion. It is demonstrated that the proposed Newton's iteration technique not only increases the convergence rate but also strongly couples the iteration between pressure and velocities. The proposed hyperbolization of the pressure correction equation is shown to increase the solver's efficiency. The above proposed methodologies were implemented in an existing CFD code, REFLEQS. The modified code was used to simulate both static and dynamic stalls on two- and three-dimensional wing-body configurations. Three-dimensional effect and flow physics are discussed.

Assessing the Dynamic Behavior of Online Q&A Knowledge Markets: A System Dynamics Approach

ERIC Educational Resources Information Center

Jafari, Mostafa; Hesamamiri, Roozbeh; Sadjadi, Jafar; Bourouni, Atieh

2012-01-01

Purpose: The objective of this paper is to propose a holistic dynamic model for understanding the behavior of a complex and internet-based kind of knowledge market by considering both social and economic interactions. Design/methodology/approach: A system dynamics (SD) model is formulated in this study to investigate the dynamic characteristics of…

Quantum dynamical simulation of photoinduced electron transfer processes in dye-semiconductor systems: theory and application to coumarin 343 at TiO₂.

PubMed

Li, Jingrui; Kondov, Ivan; Wang, Haobin; Thoss, Michael

2015-04-10

A recently developed methodology to simulate photoinduced electron transfer processes at dye-semiconductor interfaces is outlined. The methodology employs a first-principles-based model Hamiltonian and accurate quantum dynamics simulations using the multilayer multiconfiguration time-dependent Hartree approach. This method is applied to study electron injection in the dye-semiconductor system coumarin 343-TiO2. Specifically, the influence of electronic-vibrational coupling is analyzed. Extending previous work, we consider the influence of Dushinsky rotation of the normal modes as well as anharmonicities of the potential energy surfaces on the electron transfer dynamics.

Analysis of ISO NE Balancing Requirements: Uncertainty-based Secure Ranges for ISO New England Dynamic Inerchange Adjustments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Etingov, Pavel V.; Makarov, Yuri V.; Wu, Di

The document describes detailed uncertainty quantification (UQ) methodology developed by PNNL to estimate secure ranges of potential dynamic intra-hour interchange adjustments in the ISO-NE system and provides description of the dynamic interchange adjustment (DINA) tool developed under the same contract. The overall system ramping up and down capability, spinning reserve requirements, interchange schedules, load variations and uncertainties from various sources that are relevant to the ISO-NE system are incorporated into the methodology and the tool. The DINA tool has been tested by PNNL and ISO-NE staff engineers using ISO-NE data.

In Vivo Patellofemoral Contact Mechanics During Active Extension Using a Novel Dynamic MRI-based Methodology

PubMed Central

Borotikar, Bhushan S.; Sheehan, Frances T.

2017-01-01

Objectives To establish an in vivo, normative patellofemoral cartilage contact mechanics database acquired during voluntary muscle control using a novel dynamic magnetic resonance (MR) imaging-based computational methodology and validate the contact mechanics sensitivity to the known sub-millimeter methodological inaccuracies. Design Dynamic cine phase-contrast and multi-plane cine images were acquired while female subjects (n=20, sample of convenience) performed an open kinetic chain (knee flexion-extension) exercise inside a 3-Tesla MR scanner. Static cartilage models were created from high resolution three-dimensional static MR data and accurately placed in their dynamic pose at each time frame based on the cine-PC data. Cartilage contact parameters were calculated based on the surface overlap. Statistical analysis was performed using paired t-test and a one-sample repeated measures ANOVA. The sensitivity of the contact parameters to the known errors in the patellofemoral kinematics was determined. Results Peak mean patellofemoral contact area was 228.7±173.6mm2 at 40° knee angle. During extension, contact centroid and peak strain locations tracked medially on the femoral and patellar cartilage and were not significantly different from each other. At 30°, 35°, and 40° of knee extension, contact area was significantly different. Contact area and centroid locations were insensitive to rotational and translational perturbations. Conclusion This study is a first step towards unfolding the biomechanical pathways to anterior patellofemoral pain and OA using dynamic, in vivo, and accurate methodologies. The database provides crucial data for future studies and for validation of, or as an input to, computational models. PMID:24012620

Information System Design Methodology Based on PERT/CPM Networking and Optimization Techniques.

ERIC Educational Resources Information Center

Bose, Anindya

The dissertation attempts to demonstrate that the program evaluation and review technique (PERT)/Critical Path Method (CPM) or some modified version thereof can be developed into an information system design methodology. The methodology utilizes PERT/CPM which isolates the basic functional units of a system and sets them in a dynamic time/cost…

Data Mining: A Hybrid Methodology for Complex and Dynamic Research

ERIC Educational Resources Information Center

Lang, Susan; Baehr, Craig

2012-01-01

This article provides an overview of the ways in which data and text mining have potential as research methodologies in composition studies. It introduces data mining in the context of the field of composition studies and discusses ways in which this methodology can complement and extend our existing research practices by blending the best of what…

Fusion And Inference From Multiple And Massive Disparate Distributed Dynamic Data Sets

DTIC Science & Technology

2017-07-01

principled methodology for two-sample graph testing; designed a provably almost-surely perfect vertex clustering algorithm for block model graphs; proved...3.7 Semi-Supervised Clustering Methodology ...................................................................... 9 3.8 Robust Hypothesis Testing...dimensional Euclidean space – allows the full arsenal of statistical and machine learning methodology for multivariate Euclidean data to be deployed for

Health Insurance Dynamics: Methodological Considerations and a Comparison of Estimates from Two Surveys.

PubMed

Graves, John A; Mishra, Pranita

2016-10-01

To highlight key methodological issues in studying insurance dynamics and to compare estimates across two commonly used surveys. Nonelderly uninsured adults and children sampled between 2001 and 2011 in the Medical Expenditure Panel Survey and the Survey of Income and Program Participation. We utilized nonparametric Kaplan-Meier methods to estimate quantiles (25th, 50th, and 75th percentiles) in the distribution of uninsured spells. We compared estimates obtained across surveys and across different methodological approaches to address issues like attrition, seam bias, censoring and truncation, and survey weighting method. All data were drawn from publicly available household surveys. Estimated uninsured spell durations in the MEPS were longer than those observed in the SIPP. There were few changes in spell durations between 2001 and 2011, with median durations of 14 months among adults and 5-7 months among children in the MEPS, and 8 months (adults) and 4 months (children) in the SIPP. The use of panel survey data to study insurance dynamics presents a unique set of methodological challenges. Researchers should consider key analytic and survey design trade-offs when choosing which survey can best suit their research goals. © Health Research and Educational Trust.

Modified Dynamic Inversion to Control Large Flexible Aircraft: What's Going On?

NASA Technical Reports Server (NTRS)

Gregory, Irene M.

1999-01-01

High performance aircraft of the future will be designed lighter, more maneuverable, and operate over an ever expanding flight envelope. One of the largest differences from the flight control perspective between current and future advanced aircraft is elasticity. Over the last decade, dynamic inversion methodology has gained considerable popularity in application to highly maneuverable fighter aircraft, which were treated as rigid vehicles. This paper explores dynamic inversion application to an advanced highly flexible aircraft. An initial application has been made to a large flexible supersonic aircraft. In the course of controller design for this advanced vehicle, modifications were made to the standard dynamic inversion methodology. The results of this application were deemed rather promising. An analytical study has been undertaken to better understand the nature of the made modifications and to determine its general applicability. This paper presents the results of this initial analytical look at the modifications to dynamic inversion to control large flexible aircraft.

Entangled trajectories Hamiltonian dynamics for treating quantum nuclear effects

NASA Astrophysics Data System (ADS)

Smith, Brendan; Akimov, Alexey V.

2018-04-01

A simple and robust methodology, dubbed Entangled Trajectories Hamiltonian Dynamics (ETHD), is developed to capture quantum nuclear effects such as tunneling and zero-point energy through the coupling of multiple classical trajectories. The approach reformulates the classically mapped second-order Quantized Hamiltonian Dynamics (QHD-2) in terms of coupled classical trajectories. The method partially enforces the uncertainty principle and facilitates tunneling. The applicability of the method is demonstrated by studying the dynamics in symmetric double well and cubic metastable state potentials. The methodology is validated using exact quantum simulations and is compared to QHD-2. We illustrate its relationship to the rigorous Bohmian quantum potential approach, from which ETHD can be derived. Our simulations show a remarkable agreement of the ETHD calculation with the quantum results, suggesting that ETHD may be a simple and inexpensive way of including quantum nuclear effects in molecular dynamics simulations.

Coarse-grained molecular dynamics simulations for giant protein-DNA complexes

NASA Astrophysics Data System (ADS)

Takada, Shoji

Biomolecules are highly hierarchic and intrinsically flexible. Thus, computational modeling calls for multi-scale methodologies. We have been developing a coarse-grained biomolecular model where on-average 10-20 atoms are grouped into one coarse-grained (CG) particle. Interactions among CG particles are tuned based on atomistic interactions and the fluctuation matching algorithm. CG molecular dynamics methods enable us to simulate much longer time scale motions of much larger molecular systems than fully atomistic models. After broad sampling of structures with CG models, we can easily reconstruct atomistic models, from which one can continue conventional molecular dynamics simulations if desired. Here, we describe our CG modeling methodology for protein-DNA complexes, together with various biological applications, such as the DNA duplication initiation complex, model chromatins, and transcription factor dynamics on chromatin-like environment.

Multiphysics Simulation of Welding-Arc and Nozzle-Arc System: Mathematical-Model, Solution-Methodology and Validation

NASA Astrophysics Data System (ADS)

Pawar, Sumedh; Sharma, Atul

2018-01-01

This work presents mathematical model and solution methodology for a multiphysics engineering problem on arc formation during welding and inside a nozzle. A general-purpose commercial CFD solver ANSYS FLUENT 13.0.0 is used in this work. Arc formation involves strongly coupled gas dynamics and electro-dynamics, simulated by solution of coupled Navier-Stoke equations, Maxwell's equations and radiation heat-transfer equation. Validation of the present numerical methodology is demonstrated with an excellent agreement with the published results. The developed mathematical model and the user defined functions (UDFs) are independent of the geometry and are applicable to any system that involves arc-formation, in 2D axisymmetric coordinates system. The high-pressure flow of SF6 gas in the nozzle-arc system resembles arc chamber of SF6 gas circuit breaker; thus, this methodology can be extended to simulate arcing phenomenon during current interruption.

Aeroelastic Modeling of a Nozzle Startup Transient

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Zhao, Xiang; Zhang, Sijun; Chen, Yen-Sen

2014-01-01

Lateral nozzle forces are known to cause severe structural damage to any new rocket engine in development during test. While three-dimensional, transient, turbulent, chemically reacting computational fluid dynamics methodology has been demonstrated to capture major side load physics with rigid nozzles, hot-fire tests often show nozzle structure deformation during major side load events, leading to structural damages if structural strengthening measures were not taken. The modeling picture is incomplete without the capability to address the two-way responses between the structure and fluid. The objective of this study is to develop a tightly coupled aeroelastic modeling algorithm by implementing the necessary structural dynamics component into an anchored computational fluid dynamics methodology. The computational fluid dynamics component is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, while the computational structural dynamics component is developed under the framework of modal analysis. Transient aeroelastic nozzle startup analyses at sea level were performed, and the computed transient nozzle fluid-structure interaction physics presented,

Development of an Aeroelastic Modeling Capability for Transient Nozzle Side Load Analysis

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Zhao, Xiang; Zhang, Sijun; Chen, Yen-Sen

2013-01-01

Lateral nozzle forces are known to cause severe structural damage to any new rocket engine in development during test. While three-dimensional, transient, turbulent, chemically reacting computational fluid dynamics methodology has been demonstrated to capture major side load physics with rigid nozzles, hot-fire tests often show nozzle structure deformation during major side load events, leading to structural damages if structural strengthening measures were not taken. The modeling picture is incomplete without the capability to address the two-way responses between the structure and fluid. The objective of this study is to develop a coupled aeroelastic modeling capability by implementing the necessary structural dynamics component into an anchored computational fluid dynamics methodology. The computational fluid dynamics component is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, while the computational structural dynamics component is developed in the framework of modal analysis. Transient aeroelastic nozzle startup analyses of the Block I Space Shuttle Main Engine at sea level were performed. The computed results from the aeroelastic nozzle modeling are presented.

Fuzzy inductive reasoning: a consolidated approach to data-driven construction of complex dynamical systems

NASA Astrophysics Data System (ADS)

Nebot, Àngela; Mugica, Francisco

2012-10-01

Fuzzy inductive reasoning (FIR) is a modelling and simulation methodology derived from the General Systems Problem Solver. It compares favourably with other soft computing methodologies, such as neural networks, genetic or neuro-fuzzy systems, and with hard computing methodologies, such as AR, ARIMA, or NARMAX, when it is used to predict future behaviour of different kinds of systems. This paper contains an overview of the FIR methodology, its historical background, and its evolution.

Methodology of Computer-Aided Design of Variable Guide Vanes of Aircraft Engines

ERIC Educational Resources Information Center

Falaleev, Sergei V.; Melentjev, Vladimir S.; Gvozdev, Alexander S.

2016-01-01

The paper presents a methodology which helps to avoid a great amount of costly experimental research. This methodology includes thermo-gas dynamic design of an engine and its mounts, the profiling of compressor flow path and cascade design of guide vanes. Employing a method elaborated by Howell, we provide a theoretical solution to the task of…

Rigid-flexible coupling dynamic modeling and investigation of a redundantly actuated parallel manipulator with multiple actuation modes

NASA Astrophysics Data System (ADS)

Liang, Dong; Song, Yimin; Sun, Tao; Jin, Xueying

2017-09-01

A systematic dynamic modeling methodology is presented to develop the rigid-flexible coupling dynamic model (RFDM) of an emerging flexible parallel manipulator with multiple actuation modes. By virtue of assumed mode method, the general dynamic model of an arbitrary flexible body with any number of lumped parameters is derived in an explicit closed form, which possesses the modular characteristic. Then the completely dynamic model of system is formulated based on the flexible multi-body dynamics (FMD) theory and the augmented Lagrangian multipliers method. An approach of combining the Udwadia-Kalaba formulation with the hybrid TR-BDF2 numerical algorithm is proposed to address the nonlinear RFDM. Two simulation cases are performed to investigate the dynamic performance of the manipulator with different actuation modes. The results indicate that the redundant actuation modes can effectively attenuate vibration and guarantee higher dynamic performance compared to the traditional non-redundant actuation modes. Finally, a virtual prototype model is developed to demonstrate the validity of the presented RFDM. The systematic methodology proposed in this study can be conveniently extended for the dynamic modeling and controller design of other planar flexible parallel manipulators, especially the emerging ones with multiple actuation modes.

Legitimation dynamics: How SROI could mobilize resources for new constituencies.

PubMed

Cooney, Kate

2017-10-01

The following critical essay on the social return on investment (SROI) methodology is broken into two parts. In the first section, focusing on the categorization dynamics of the SROI, I review a set of methodological and ethical tensions surrounding the SROI, using examples from my own work and other published works using SROI. These tensions include the fact that the project requires standardization to achieve comparability while concurrently offering a flexibility in constructing a narrative of impact that is attractive to users. In the second section, focusing on the legitimation dynamics, I define a narrow scope for where, despite the aforementioned pitfalls, that the SROI can be quite effective in building a rhetorical argument for directing material resources. The essay argues that despite ongoing methodological challenges, the investor lens and market logic undergirding the metric provide a powerful frame for persuasion that can be used to construct worthiness and value creation for constituents not already constructed as such. Copyright © 2016 Elsevier Ltd. All rights reserved.

Complex dynamic in ecological time series

Treesearch

Peter Turchin; Andrew D. Taylor

1992-01-01

Although the possibility of complex dynamical behaviors-limit cycles, quasiperiodic oscillations, and aperiodic chaos-has been recognized theoretically, most ecologists are skeptical of their importance in nature. In this paper we develop a methodology for reconstructing endogenous (or deterministic) dynamics from ecological time series. Our method consists of fitting...

Canalization and Control in Automata Networks: Body Segmentation in Drosophila melanogaster

PubMed Central

Marques-Pita, Manuel; Rocha, Luis M.

2013-01-01

We present schema redescription as a methodology to characterize canalization in automata networks used to model biochemical regulation and signalling. In our formulation, canalization becomes synonymous with redundancy present in the logic of automata. This results in straightforward measures to quantify canalization in an automaton (micro-level), which is in turn integrated into a highly scalable framework to characterize the collective dynamics of large-scale automata networks (macro-level). This way, our approach provides a method to link micro- to macro-level dynamics – a crux of complexity. Several new results ensue from this methodology: uncovering of dynamical modularity (modules in the dynamics rather than in the structure of networks), identification of minimal conditions and critical nodes to control the convergence to attractors, simulation of dynamical behaviour from incomplete information about initial conditions, and measures of macro-level canalization and robustness to perturbations. We exemplify our methodology with a well-known model of the intra- and inter cellular genetic regulation of body segmentation in Drosophila melanogaster. We use this model to show that our analysis does not contradict any previous findings. But we also obtain new knowledge about its behaviour: a better understanding of the size of its wild-type attractor basin (larger than previously thought), the identification of novel minimal conditions and critical nodes that control wild-type behaviour, and the resilience of these to stochastic interventions. Our methodology is applicable to any complex network that can be modelled using automata, but we focus on biochemical regulation and signalling, towards a better understanding of the (decentralized) control that orchestrates cellular activity – with the ultimate goal of explaining how do cells and tissues ‘compute’. PMID:23520449

Canalization and control in automata networks: body segmentation in Drosophila melanogaster.

PubMed

Marques-Pita, Manuel; Rocha, Luis M

2013-01-01

We present schema redescription as a methodology to characterize canalization in automata networks used to model biochemical regulation and signalling. In our formulation, canalization becomes synonymous with redundancy present in the logic of automata. This results in straightforward measures to quantify canalization in an automaton (micro-level), which is in turn integrated into a highly scalable framework to characterize the collective dynamics of large-scale automata networks (macro-level). This way, our approach provides a method to link micro- to macro-level dynamics--a crux of complexity. Several new results ensue from this methodology: uncovering of dynamical modularity (modules in the dynamics rather than in the structure of networks), identification of minimal conditions and critical nodes to control the convergence to attractors, simulation of dynamical behaviour from incomplete information about initial conditions, and measures of macro-level canalization and robustness to perturbations. We exemplify our methodology with a well-known model of the intra- and inter cellular genetic regulation of body segmentation in Drosophila melanogaster. We use this model to show that our analysis does not contradict any previous findings. But we also obtain new knowledge about its behaviour: a better understanding of the size of its wild-type attractor basin (larger than previously thought), the identification of novel minimal conditions and critical nodes that control wild-type behaviour, and the resilience of these to stochastic interventions. Our methodology is applicable to any complex network that can be modelled using automata, but we focus on biochemical regulation and signalling, towards a better understanding of the (decentralized) control that orchestrates cellular activity--with the ultimate goal of explaining how do cells and tissues 'compute'.

Capturing complexity in work disability research: application of system dynamics modeling methodology.

PubMed

Jetha, Arif; Pransky, Glenn; Hettinger, Lawrence J

2016-01-01

Work disability (WD) is characterized by variable and occasionally undesirable outcomes. The underlying determinants of WD outcomes include patterns of dynamic relationships among health, personal, organizational and regulatory factors that have been challenging to characterize, and inadequately represented by contemporary WD models. System dynamics modeling (SDM) methodology applies a sociotechnical systems thinking lens to view WD systems as comprising a range of influential factors linked by feedback relationships. SDM can potentially overcome limitations in contemporary WD models by uncovering causal feedback relationships, and conceptualizing dynamic system behaviors. It employs a collaborative and stakeholder-based model building methodology to create a visual depiction of the system as a whole. SDM can also enable researchers to run dynamic simulations to provide evidence of anticipated or unanticipated outcomes that could result from policy and programmatic intervention. SDM may advance rehabilitation research by providing greater insights into the structure and dynamics of WD systems while helping to understand inherent complexity. Challenges related to data availability, determining validity, and the extensive time and technical skill requirements for model building may limit SDM's use in the field and should be considered. Contemporary work disability (WD) models provide limited insight into complexity associated with WD processes. System dynamics modeling (SDM) has the potential to capture complexity through a stakeholder-based approach that generates a simulation model consisting of multiple feedback loops. SDM may enable WD researchers and practitioners to understand the structure and behavior of the WD system as a whole, and inform development of improved strategies to manage straightforward and complex WD cases.

Coupled socioeconomic-crop modelling for the participatory local analysis of climate change impacts on smallholder farmers in Guatemala

NASA Astrophysics Data System (ADS)

Malard, J. J.; Adamowski, J. F.; Wang, L. Y.; Rojas, M.; Carrera, J.; Gálvez, J.; Tuy, H. A.; Melgar-Quiñonez, H.

2015-12-01

The modelling of the impacts of climate change on agriculture requires the inclusion of socio-economic factors. However, while cropping models and economic models of agricultural systems are common, dynamically coupled socio-economic-biophysical models have not received as much success. A promising methodology for modelling the socioeconomic aspects of coupled natural-human systems is participatory system dynamics modelling, in which stakeholders develop mental maps of the socio-economic system that are then turned into quantified simulation models. This methodology has been successful in the water resources management field. However, while the stocks and flows of water resources have also been represented within the system dynamics modelling framework and thus coupled to the socioeconomic portion of the model, cropping models are ill-suited for such reformulation. In addition, most of these system dynamics models were developed without stakeholder input, limiting the scope for the adoption and implementation of their results. We therefore propose a new methodology for the analysis of climate change variability on agroecosystems which uses dynamically coupled system dynamics (socio-economic) and biophysical (cropping) models to represent both physical and socioeconomic aspects of the agricultural system, using two case studies (intensive market-based agricultural development versus subsistence crop-based development) from rural Guatemala. The system dynamics model component is developed with relevant governmental and NGO stakeholders from rural and agricultural development in the case study regions and includes such processes as education, poverty and food security. Common variables with the cropping models (yield and agricultural management choices) are then used to dynamically couple the two models together, allowing for the analysis of the agroeconomic system's response to and resilience against various climatic and socioeconomic shocks.

Tracking Team Dynamic Strategy Implemented in Sly Fox Mission 22

DTIC Science & Technology

communication between team members and track the overall status of the team social dynamic. This paper provides a detailed account of the need, methodology , results, benefits, and limitations of this strategy.

Discrete Adjoint-Based Design Optimization of Unsteady Turbulent Flows on Dynamic Unstructured Grids

NASA Technical Reports Server (NTRS)

Nielsen, Eric J.; Diskin, Boris; Yamaleev, Nail K.

2009-01-01

An adjoint-based methodology for design optimization of unsteady turbulent flows on dynamic unstructured grids is described. The implementation relies on an existing unsteady three-dimensional unstructured grid solver capable of dynamic mesh simulations and discrete adjoint capabilities previously developed for steady flows. The discrete equations for the primal and adjoint systems are presented for the backward-difference family of time-integration schemes on both static and dynamic grids. The consistency of sensitivity derivatives is established via comparisons with complex-variable computations. The current work is believed to be the first verified implementation of an adjoint-based optimization methodology for the true time-dependent formulation of the Navier-Stokes equations in a practical computational code. Large-scale shape optimizations are demonstrated for turbulent flows over a tiltrotor geometry and a simulated aeroelastic motion of a fighter jet.

Stability Result For Dynamic Inversion Devised to Control Large Flexible Aircraft

NASA Technical Reports Server (NTRS)

Gregory, Irene M.

2001-01-01

High performance aircraft of the future will be designed lighter, more maneuverable, and operate over an ever expanding flight envelope. One of the largest differences from the flight control perspective between current and future advanced aircraft is elasticity. Over the last decade, dynamic inversion methodology has gained considerable popularity in application to highly maneuverable fighter aircraft, which were treated as rigid vehicles. This paper is an initial attempt to establish global stability results for dynamic inversion methodology as applied to a large, flexible aircraft. This work builds on a previous result for rigid fighter aircraft and adds a new level of complexity that is the flexible aircraft dynamics, which cannot be ignored even in the most basic flight control. The results arise from observations of the control laws designed for a new generation of the High-Speed Civil Transport aircraft.

High-frequency intrinsic dynamics of the electrocaloric effect from direct atomistic simulations

NASA Astrophysics Data System (ADS)

Lisenkov, S.; Ponomareva, I.

2018-05-01

We propose a computational methodology capable of harvesting isothermal heat and entropy change in molecular dynamics simulations. The methodology is applied to study high-frequency dynamics of the electrocaloric effect (ECE) in ferroelectric PbTiO3. ECE is associated with a reversible change in temperature under adiabatic application of electric field or with a reversible change in entropy under isothermal application of the electric field. Accurate assessment of electrocaloric performance requires the knowledge of three quantities: isothermal heat, isothermal entropy change, and adiabatic temperature change. Our methodology allows computations of all these quantities directly, that is, without restoring to the reversible thermodynamical models. Consequently, it captures both reversible and irreversible effects, which is critical for ECE simulations. The approach is well suited to address the dynamics of the ECE, which so far remains underexplored. We report the following basic features of the intrinsic dynamics of ECE: (i) the ECE is independent of the electric field frequency, rate of application, or field profile; (ii) the effect persists up to the frequencies associated with the onset of dielectric losses and deteriorates from there due to the creation of irreversible entropy; and (iii) in the vicinity of the phase transition and in the paraelectric phase the onset of irreversible dynamics occurs at lower frequency as compared to the ferroelectric phase. The latter is attributed to lower intrinsic soft-mode frequencies and and larger losses in the paraelectric phase.

A Dynamic Ensemble for Second Language Research: Putting Complexity Theory into Practice

ERIC Educational Resources Information Center

Hiver, Phil; Al-Hoorie, Ali H.

2016-01-01

In this article, we introduce a template of methodological considerations, termed "the dynamic ensemble," for scholars doing or evaluating empirical second language development (SLD) research within a complexity/dynamic systems theory (CDST) framework. Given that CDST principles have yielded significant insight into SLD and have become…

Tenth Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion, part 1

NASA Technical Reports Server (NTRS)

Williams, R. W. (Compiler)

1992-01-01

Experimental and computational fluid dynamic activities in rocket propulsion were discussed. The workshop was an open meeting of government, industry, and academia. A broad number of topics were discussed including computational fluid dynamic methodology, liquid and solid rocket propulsion, turbomachinery, combustion, heat transfer, and grid generation.

System Dynamics Aviation Readiness Modeling Demonstration

DTIC Science & Technology

2005-08-31

requirements. It is recommended that the Naval Aviation Enterprise take a close look at the requirements i.e., performance measures, methodology ...unit’s capability to perform specific Joint Mission Essential Task List (JMETL) requirements now and in the future. This assessment methodology must...the time-associated costs. The new methodology must base decisions on currently available data and databases. A “useful” readiness model should be

Methodology for extracting local constants from petroleum cracking flows

DOEpatents

Chang, Shen-Lin; Lottes, Steven A.; Zhou, Chenn Q.

2000-01-01

A methodology provides for the extraction of local chemical kinetic model constants for use in a reacting flow computational fluid dynamics (CFD) computer code with chemical kinetic computations to optimize the operating conditions or design of the system, including retrofit design improvements to existing systems. The coupled CFD and kinetic computer code are used in combination with data obtained from a matrix of experimental tests to extract the kinetic constants. Local fluid dynamic effects are implicitly included in the extracted local kinetic constants for each particular application system to which the methodology is applied. The extracted local kinetic model constants work well over a fairly broad range of operating conditions for specific and complex reaction sets in specific and complex reactor systems. While disclosed in terms of use in a Fluid Catalytic Cracking (FCC) riser, the inventive methodology has application in virtually any reaction set to extract constants for any particular application and reaction set formulation. The methodology includes the step of: (1) selecting the test data sets for various conditions; (2) establishing the general trend of the parametric effect on the measured product yields; (3) calculating product yields for the selected test conditions using coupled computational fluid dynamics and chemical kinetics; (4) adjusting the local kinetic constants to match calculated product yields with experimental data; and (5) validating the determined set of local kinetic constants by comparing the calculated results with experimental data from additional test runs at different operating conditions.

Modeling Common-Sense Decisions in Artificial Intelligence

NASA Technical Reports Server (NTRS)

Zak, Michail

2010-01-01

A methodology has been conceived for efficient synthesis of dynamical models that simulate common-sense decision- making processes. This methodology is intended to contribute to the design of artificial-intelligence systems that could imitate human common-sense decision making or assist humans in making correct decisions in unanticipated circumstances. This methodology is a product of continuing research on mathematical models of the behaviors of single- and multi-agent systems known in biology, economics, and sociology, ranging from a single-cell organism at one extreme to the whole of human society at the other extreme. Earlier results of this research were reported in several prior NASA Tech Briefs articles, the three most recent and relevant being Characteristics of Dynamics of Intelligent Systems (NPO -21037), NASA Tech Briefs, Vol. 26, No. 12 (December 2002), page 48; Self-Supervised Dynamical Systems (NPO-30634), NASA Tech Briefs, Vol. 27, No. 3 (March 2003), page 72; and Complexity for Survival of Living Systems (NPO- 43302), NASA Tech Briefs, Vol. 33, No. 7 (July 2009), page 62. The methodology involves the concepts reported previously, albeit viewed from a different perspective. One of the main underlying ideas is to extend the application of physical first principles to the behaviors of living systems. Models of motor dynamics are used to simulate the observable behaviors of systems or objects of interest, and models of mental dynamics are used to represent the evolution of the corresponding knowledge bases. For a given system, the knowledge base is modeled in the form of probability distributions and the mental dynamics is represented by models of the evolution of the probability densities or, equivalently, models of flows of information. Autonomy is imparted to the decisionmaking process by feedback from mental to motor dynamics. This feedback replaces unavailable external information by information stored in the internal knowledge base. Representation of the dynamical models in a parameterized form reduces the task of common-sense-based decision making to a solution of the following hetero-associated-memory problem: store a set of m predetermined stochastic processes given by their probability distributions in such a way that when presented with an unexpected change in the form of an input out of the set of M inputs, the coupled motormental dynamics converges to the corresponding one of the m pre-assigned stochastic process, and a sample of this process represents the decision.

Determination of the coefficient of dynamic friction between coatings of alumina and metallic materials

NASA Astrophysics Data System (ADS)

Santos, A.; Córdoba, E.; Ramírez, Z.; Sierra, C.; Ortega, Y.

2017-12-01

This project aims to determine the coefficient of dynamic friction between micrometric size coatings of alumina and metallic materials (Steel and aluminium); the methodology used to achieve the proposed objective consisted of 4 phases, in the first one was developed a procedure that allowed, from a Pin on Disk machine built based on the specifications given by the ASTM G99-05 standard (Standard test method for wear tests with a Pin on Disk machine), to determine the coefficient of dynamic friction between two materials in contact; subsequently the methodology was verified through tests between steel-steel and steel-aluminium, due to these values are widely reported in the literature; as a third step, deposits of alumina particles of micrometric size were made on a steel substrate through thermal spraying by flame; finally, the tests were carried out between pins of steel of aluminium and alumina coating to determine the coefficients of dynamic friction between these two surfaces. The results of the project allowed to verify that the developed methodology is valid to obtain coefficients of dynamic friction between surfaces in contact since the percentages of error were of 3.5% and 2.1% for steel-steel and aluminium-steel, respectively; additionally, it was found that the coefficient of friction between steel-alumina coatings is 0.36 and aluminium-alumina coating is 0.25.

A Methodology for Dynamic Security Risk Quantification and Optimal Resource Allocation of Security Assets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brigantic, Robert T.; Betzsold, Nick J.; Bakker, Craig KR

In this presentation we overview a methodology for dynamic security risk quantification and optimal resource allocation of security assets for high profile venues. This methodology is especially applicable to venues that require security screening operations such as mass transit (e.g., train or airport terminals), critical infrastructure protection (e.g., government buildings), and largescale public events (e.g., concerts or professional sports). The method starts by decomposing the three core components of risk -- threat, vulnerability, and consequence -- into their various subcomponents. For instance, vulnerability can be decomposed into availability, accessibility, organic security, and target hardness and each of these can bemore » evaluated against the potential threats of interest for the given venue. Once evaluated, these subcomponents are rolled back up to compute the specific value for the vulnerability core risk component. Likewise, the same is done for consequence and threat, and then risk is computed as the product of these three components. A key aspect of our methodology is dynamically quantifying risk. That is, we incorporate the ability to uniquely allow the subcomponents and core components, and in turn, risk, to be quantified as a continuous function of time throughout the day, week, month, or year as appropriate.« less

Identification of Dynamic Simulation Models for Variable Speed Pumped Storage Power Plants

NASA Astrophysics Data System (ADS)

Moreira, C.; Fulgêncio, N.; Silva, B.; Nicolet, C.; Béguin, A.

2017-04-01

This paper addresses the identification of reduced order models for variable speed pump-turbine plants, including the representation of the dynamic behaviour of the main components: hydraulic system, turbine governors, electromechanical equipment and power converters. A methodology for the identification of appropriated reduced order models both for turbine and pump operating modes is presented and discussed. The methodological approach consists of three main steps: 1) detailed pumped-storage power plant modelling in SIMSEN; 2) reduced order models identification and 3) specification of test conditions for performance evaluation.

Mass-Related Dynamical Barriers in Triatomic Reactions

NASA Astrophysics Data System (ADS)

Yanao, T.; Koon, W. S.; Marsden, J. E.

2006-06-01

A methodology is given to determine the effect of different mass distributions for triatomic reactions using the geometry of shape space. Atomic masses are incorporated into the non-Euclidean shape space metric after the separation of rotations. Using the equations of motion in this non-Euclidean shape space, an averaged field of velocity-dependent fictitious forces is determined. This force field, as opposed to the force arising from the potential, dominates branching ratios of isomerization dynamics of a triatomic molecule. This methodology may be useful for qualitative prediction of branching ratios in general triatomic reactions.

Equivalent Viscous Damping Methodologies Applied on VEGA Launch Vehicle Numerical Model

NASA Astrophysics Data System (ADS)

Bartoccini, D.; Di Trapani, C.; Fransen, S.

2014-06-01

Part of the mission analysis of a spacecraft is the so- called launcher-satellite coupled loads analysis which aims at computing the dynamic environment of the satellite and of the launch vehicle for the most severe load cases in flight. Evidently the damping of the coupled system shall be defined with care as to not overestimate or underestimate the loads derived for the spacecraft. In this paper the application of several EqVD (Equivalent Viscous Damping) for Craig an Bampton (CB)-systems are investigated. Based on the structural damping defined for the various materials in the parent FE-models of the CB-components, EqVD matrices can be computed according to different methodologies. The effect of these methodologies on the numerical reconstruction of the VEGA launch vehicle dynamic environment will be presented.

Development of a Design Methodology for Reconfigurable Flight Control Systems

NASA Technical Reports Server (NTRS)

Hess, Ronald A.; McLean, C.

2000-01-01

A methodology is presented for the design of flight control systems that exhibit stability and performance-robustness in the presence of actuator failures. The design is based upon two elements. The first element consists of a control law that will ensure at least stability in the presence of a class of actuator failures. This law is created by inner-loop, reduced-order, linear dynamic inversion, and outer-loop compensation based upon Quantitative Feedback Theory. The second element consists of adaptive compensators obtained from simple and approximate time-domain identification of the dynamics of the 'effective vehicle' with failed actuator(s). An example involving the lateral-directional control of a fighter aircraft is employed both to introduce the proposed methodology and to demonstrate its effectiveness and limitations.

Calculation of Dynamic Loads Due to Random Vibration Environments in Rocket Engine Systems

NASA Technical Reports Server (NTRS)

Christensen, Eric R.; Brown, Andrew M.; Frady, Greg P.

2007-01-01

An important part of rocket engine design is the calculation of random dynamic loads resulting from internal engine "self-induced" sources. These loads are random in nature and can greatly influence the weight of many engine components. Several methodologies for calculating random loads are discussed and then compared to test results using a dynamic testbed consisting of a 60K thrust engine. The engine was tested in a free-free condition with known random force inputs from shakers attached to three locations near the main noise sources on the engine. Accelerations and strains were measured at several critical locations on the engines and then compared to the analytical results using two different random response methodologies.

Weighted Ensemble Simulation: Review of Methodology, Applications, and Software

PubMed Central

Zuckerman, Daniel M.; Chong, Lillian T.

2018-01-01

The weighted ensemble (WE) methodology orchestrates quasi-independent parallel simulations run with intermittent communication that can enhance sampling of rare events such as protein conformational changes, folding, and binding. The WE strategy can achieve superlinear scaling—the unbiased estimation of key observables such as rate constants and equilibrium state populations to greater precision than would be possible with ordinary parallel simulation. WE software can be used to control any dynamics engine, such as standard molecular dynamics and cell-modeling packages. This article reviews the theoretical basis of WE and goes on to describe successful applications to a number of complex biological processes—protein conformational transitions, (un)binding, and assembly processes, as well as cell-scale processes in systems biology. We furthermore discuss the challenges that need to be overcome in the next phase of WE methodological development. Overall, the combined advances in WE methodology and software have enabled the simulation of long-timescale processes that would otherwise not be practical on typical computing resources using standard simulation. PMID:28301772

Thermal Hydraulics Design and Analysis Methodology for a Solid-Core Nuclear Thermal Rocket Engine Thrust Chamber

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Canabal, Francisco; Chen, Yen-Sen; Cheng, Gary; Ito, Yasushi

2013-01-01

Nuclear thermal propulsion is a leading candidate for in-space propulsion for human Mars missions. This chapter describes a thermal hydraulics design and analysis methodology developed at the NASA Marshall Space Flight Center, in support of the nuclear thermal propulsion development effort. The objective of this campaign is to bridge the design methods in the Rover/NERVA era, with a modern computational fluid dynamics and heat transfer methodology, to predict thermal, fluid, and hydrogen environments of a hypothetical solid-core, nuclear thermal engine the Small Engine, designed in the 1960s. The computational methodology is based on an unstructured-grid, pressure-based, all speeds, chemically reacting, computational fluid dynamics and heat transfer platform, while formulations of flow and heat transfer through porous and solid media were implemented to describe those of hydrogen flow channels inside the solid24 core. Design analyses of a single flow element and the entire solid-core thrust chamber of the Small Engine were performed and the results are presented herein

Weighted Ensemble Simulation: Review of Methodology, Applications, and Software.

PubMed

Zuckerman, Daniel M; Chong, Lillian T

2017-05-22

The weighted ensemble (WE) methodology orchestrates quasi-independent parallel simulations run with intermittent communication that can enhance sampling of rare events such as protein conformational changes, folding, and binding. The WE strategy can achieve superlinear scaling-the unbiased estimation of key observables such as rate constants and equilibrium state populations to greater precision than would be possible with ordinary parallel simulation. WE software can be used to control any dynamics engine, such as standard molecular dynamics and cell-modeling packages. This article reviews the theoretical basis of WE and goes on to describe successful applications to a number of complex biological processes-protein conformational transitions, (un)binding, and assembly processes, as well as cell-scale processes in systems biology. We furthermore discuss the challenges that need to be overcome in the next phase of WE methodological development. Overall, the combined advances in WE methodology and software have enabled the simulation of long-timescale processes that would otherwise not be practical on typical computing resources using standard simulation.

Force on Force Modeling with Formal Task Structures and Dynamic Geometry

DTIC Science & Technology

2017-03-24

task framework, derived using the MMF methodology to structure a complex mission. It further demonstrated the integration of effects from a range of...application methodology was intended to support a combined developmental testing (DT) and operational testing (OT) strategy for selected systems under test... methodology to develop new or modify existing Models and Simulations (M&S) to: • Apply data from multiple, distributed sources (including test

A dynamic multi-scale Markov model based methodology for remaining life prediction

NASA Astrophysics Data System (ADS)

Yan, Jihong; Guo, Chaozhong; Wang, Xing

2011-05-01

The ability to accurately predict the remaining life of partially degraded components is crucial in prognostics. In this paper, a performance degradation index is designed using multi-feature fusion techniques to represent deterioration severities of facilities. Based on this indicator, an improved Markov model is proposed for remaining life prediction. Fuzzy C-Means (FCM) algorithm is employed to perform state division for Markov model in order to avoid the uncertainty of state division caused by the hard division approach. Considering the influence of both historical and real time data, a dynamic prediction method is introduced into Markov model by a weighted coefficient. Multi-scale theory is employed to solve the state division problem of multi-sample prediction. Consequently, a dynamic multi-scale Markov model is constructed. An experiment is designed based on a Bently-RK4 rotor testbed to validate the dynamic multi-scale Markov model, experimental results illustrate the effectiveness of the methodology.

A combinatorial framework to quantify peak/pit asymmetries in complex dynamics.

PubMed

Hasson, Uri; Iacovacci, Jacopo; Davis, Ben; Flanagan, Ryan; Tagliazucchi, Enzo; Laufs, Helmut; Lacasa, Lucas

2018-02-23

We explore a combinatorial framework which efficiently quantifies the asymmetries between minima and maxima in local fluctuations of time series. We first showcase its performance by applying it to a battery of synthetic cases. We find rigorous results on some canonical dynamical models (stochastic processes with and without correlations, chaotic processes) complemented by extensive numerical simulations for a range of processes which indicate that the methodology correctly distinguishes different complex dynamics and outperforms state of the art metrics in several cases. Subsequently, we apply this methodology to real-world problems emerging across several disciplines including cases in neurobiology, finance and climate science. We conclude that differences between the statistics of local maxima and local minima in time series are highly informative of the complex underlying dynamics and a graph-theoretic extraction procedure allows to use these features for statistical learning purposes.

A CFD study of complex missile and store configurations in relative motion

NASA Technical Reports Server (NTRS)

Baysal, Oktay

1995-01-01

An investigation was conducted from May 16, 1990 to August 31, 1994 on the development of computational fluid dynamics (CFD) methodologies for complex missiles and the store separation problem. These flowfields involved multiple-component configurations, where at least one of the objects was engaged in relative motion. The two most important issues that had to be addressed were: (1) the unsteadiness of the flowfields (time-accurate and efficient CFD algorithms for the unsteady equations), and (2) the generation of grid systems which would permit multiple and moving bodies in the computational domain (dynamic domain decomposition). The study produced two competing and promising methodologies, and their proof-of-concept cases, which have been reported in the open literature: (1) Unsteady solutions on dynamic, overlapped grids, which may also be perceived as moving, locally-structured grids, and (2) Unsteady solutions on dynamic, unstructured grids.

Experimental and analytical investigation of inertial propulsion mechanisms and motion simulation of rigid multi-body mechanical systems

NASA Astrophysics Data System (ADS)

Almesallmy, Mohammed

Methodologies are developed for dynamic analysis of mechanical systems with emphasis on inertial propulsion systems. This work adopted the Lagrangian methodology. Lagrangian methodology is the most efficient classical computational technique, which we call Equations of Motion Code (EOMC). The EOMC is applied to several simple dynamic mechanical systems for easier understanding of the method and to aid other investigators in developing equations of motion of any dynamic system. In addition, it is applied to a rigid multibody system, such as Thomson IPS [Thomson 1986]. Furthermore, a simple symbolic algorithm is developed using Maple software, which can be used to convert any nonlinear n-order ordinary differential equation (ODE) systems into 1st-order ODE system in ready format to be used in Matlab software. A side issue, but equally important, we have started corresponding with the U.S. Patent office to persuade them that patent applications, claiming gross linear motion based on inertial propulsion systems should be automatically rejected. The precedent is rejection of patent applications involving perpetual motion machines.

Organizing Performance Requirements For Dynamical Systems

NASA Technical Reports Server (NTRS)

Malchow, Harvey L.; Croopnick, Steven R.

1990-01-01

Paper describes methodology for establishing performance requirements for complicated dynamical systems. Uses top-down approach. In series of steps, makes connections between high-level mission requirements and lower-level functional performance requirements. Provides systematic delineation of elements accommodating design compromises.

Analog Integrated Circuit Design for Spike Time Dependent Encoder and Reservoir in Reservoir Computing Processors

DTIC Science & Technology

2018-01-01

14. ABSTRACT The objective of this effort was to: (a) develop novel and fundamental methodologies for data representation using hardware-based spike...Distribution Unlimited. 1 1.0 SUMMARY This effort is a critical part of an overall program to develop novel and fundamental methodologies for data...to fabrication a dynamic-reservoir circuit that utilizes sensory encoding methodologies similar to those employed in biological brains. Inspired

Development of test methodology for dynamic mechanical analysis instrumentation

NASA Technical Reports Server (NTRS)

Allen, V. R.

1982-01-01

Dynamic mechanical analysis instrumentation was used for the development of specific test methodology in the determination of engineering parameters of selected materials, esp. plastics and elastomers, over a broad range of temperature with selected environment. The methodology for routine procedures was established with specific attention given to sample geometry, sample size, and mounting techniques. The basic software of the duPont 1090 thermal analyzer was used for data reduction which simplify the theoretical interpretation. Clamps were developed which allowed 'relative' damping during the cure cycle to be measured for the fiber-glass supported resin. The correlation of fracture energy 'toughness' (or impact strength) with the low temperature (glassy) relaxation responses for a 'rubber-modified' epoxy system was negative in result because the low-temperature dispersion mode (-80 C) of the modifier coincided with that of the epoxy matrix, making quantitative comparison unrealistic.

Modal interactions due to friction in the nonlinear vibration response of the "Harmony" test structure: Experiments and simulations

NASA Astrophysics Data System (ADS)

Claeys, M.; Sinou, J.-J.; Lambelin, J.-P.; Todeschini, R.

2016-08-01

The nonlinear vibration response of an assembly with friction joints - named "Harmony" - is studied both experimentally and numerically. The experimental results exhibit a softening effect and an increase of dissipation with excitation level. Modal interactions due to friction are also evidenced. The numerical methodology proposed groups together well-known structural dynamic methods, including finite elements, substructuring, Harmonic Balance and continuation methods. On the one hand, the application of this methodology proves its capacity to treat a complex system where several friction movements occur at the same time. On the other hand, the main contribution of this paper is the experimental and numerical study of evidence of modal interactions due to friction. The simulation methodology succeeds in reproducing complex form of dynamic behavior such as these modal interactions.

A system management methodology for building successful resource management systems

NASA Technical Reports Server (NTRS)

Hornstein, Rhoda Shaller; Willoughby, John K.

1989-01-01

This paper presents a system management methodology for building successful resource management systems that possess lifecycle effectiveness. This methodology is based on an analysis of the traditional practice of Systems Engineering Management as it applies to the development of resource management systems. The analysis produced fifteen significant findings presented as recommended adaptations to the traditional practice of Systems Engineering Management to accommodate system development when the requirements are incomplete, unquantifiable, ambiguous and dynamic. Ten recommended adaptations to achieve operational effectiveness when requirements are incomplete, unquantifiable or ambiguous are presented and discussed. Five recommended adaptations to achieve system extensibility when requirements are dynamic are also presented and discussed. The authors conclude that the recommended adaptations to the traditional practice of Systems Engineering Management should be implemented for future resource management systems and that the technology exists to build these systems extensibly.

Feminist Research Methodology Groups: Origins, Forms, Functions.

ERIC Educational Resources Information Center

Reinharz, Shulamit

Feminist Research Methodology Groups (FRMGs) have developed as a specific type of women's group in which feminist academics can find supportive audiences for their work while contributing to a feminist redefinition of research methods. An analysis of two FRMGs reveals common characteristics, dynamics, and outcomes. Both were limited to small…

A Dissemination Methodology for Learning and Teaching Developments through Engaging and Embedding

ERIC Educational Resources Information Center

Treleaven, Lesley; Sykes, Chris; Ormiston, Jarrod

2012-01-01

Dissemination of learning and teaching innovation in higher education requires approaches to change that are socially contextualised, dynamic and self-reflexive. This article, therefore, presents a methodology for dissemination employing an embedding heuristic and engaging in participatory action research. The embedding approach emphasises three…

Research Methodology on Language Development from a Complex Systems Perspective

ERIC Educational Resources Information Center

Larsen-Freeman, Diane; Cameron, Lynne

2008-01-01

Changes to research methodology motivated by the adoption of a complexity theory perspective on language development are considered. The dynamic, nonlinear, and open nature of complex systems, together with their tendency toward self-organization and interaction across levels and timescales, requires changes in traditional views of the functions…

Application of control theory to dynamic systems simulation

NASA Technical Reports Server (NTRS)

Auslander, D. M.; Spear, R. C.; Young, G. E.

1982-01-01

The application of control theory is applied to dynamic systems simulation. Theory and methodology applicable to controlled ecological life support systems are considered. Spatial effects on system stability, design of control systems with uncertain parameters, and an interactive computing language (PARASOL-II) designed for dynamic system simulation, report quality graphics, data acquisition, and simple real time control are discussed.

Emotion Regulation and the Dynamics of Feelings: A Conceptual and Methodological Framework

ERIC Educational Resources Information Center

Hoeksma, Jan B.; Oosterlaan, Jaap; Schipper, Eline M.

2004-01-01

The emotional system is defined as a dynamical system that has neurological and biochemical structures that force the system to change in a regular and consistent way. This dynamic view allows for an alternative definition of emotion regulation, which describes when emotion regulation is needed, identifies its goal, and illustrates how regulation…

Identifying Complex Dynamics in Social Systems: A New Methodological Approach Applied to Study School Segregation

ERIC Educational Resources Information Center

Spaiser, Viktoria; Hedström, Peter; Ranganathan, Shyam; Jansson, Kim; Nordvik, Monica K.; Sumpter, David J. T.

2018-01-01

It is widely recognized that segregation processes are often the result of complex nonlinear dynamics. Empirical analyses of complex dynamics are however rare, because there is a lack of appropriate empirical modeling techniques that are capable of capturing complex patterns and nonlinearities. At the same time, we know that many social phenomena…

Membrane Insertion Profiles of Peptides Probed by Molecular Dynamics Simulations

DTIC Science & Technology

2008-07-17

Membrane insertion profiles of peptides probed by molecular dynamics simulations In-Chul Yeh,* Mark A. Olson,# Michael S. Lee,*#§ and Anders...a methodology based on molecular dynamics simulation techniques to probe the insertion profiles of small peptides across the membrane interface. The...profiles of peptides probed by molecular dynamics simulations 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d

Computational Fluid Dynamics: Past, Present, And Future

NASA Technical Reports Server (NTRS)

Kutler, Paul

1988-01-01

Paper reviews development of computational fluid dynamics and explores future prospects of technology. Report covers such topics as computer technology, turbulence, development of solution methodology, developemnt of algorithms, definition of flow geometries, generation of computational grids, and pre- and post-data processing.

Development of asphalt dynamic modulus master curve using falling weight deflectometer measurements.

DOT National Transportation Integrated Search

2014-06-01

The asphalt concrete (AC) dynamic modulus (|E*|) is a key design parameter in mechanistic-based pavement design : methodologies such as the American Association of State Highway and Transportation Officials (AASHTO) MEPDG/Pavement-ME Design. The obje...

Extending the essential dynamics analysis to investigate molecular properties: application to the redox potential of proteins.

PubMed

Zanetti-Polzi, Laura; Corni, Stefano; Daidone, Isabella; Amadei, Andrea

2016-07-21

Here, a methodology is proposed to investigate the collective fluctuation modes of an arbitrary set of observables, maximally contributing to the fluctuation of another functionally relevant observable. The methodology, based on the analysis of fully classical molecular dynamics (MD) simulations, exploits the essential dynamics (ED) method, originally developed to analyse the collective motions in proteins. We apply this methodology to identify the residues that are more relevant for determining the reduction potential (E(0)) of a redox-active protein. To this aim, the fluctuation modes of the single-residue electrostatic potentials mostly contributing to the fluctuations of the total electrostatic potential (the main determinant of E(0)) are investigated for wild-type azurin and two of its mutants with a higher E(0). By comparing the results here obtained with a previous study on the same systems [Zanetti-Polzi et al., Org. Biomol. Chem., 2015, 13, 11003] we show that the proposed methodology is able to identify the key sites that determine E(0). This information can be used for a general deeper understanding of the molecular mechanisms on the basis of the redox properties of the proteins under investigation, as well as for the rational design of mutants with a higher or lower E(0). From the results of the present analysis we propose a new azurin mutant that, according to our calculations, shows a further increase of E(0).

Compressive Feedback Control Design for Spatially Distributed Systems

DTIC Science & Technology

2017-01-03

NecSys 2015 & 2016 Abstract The goal of this research is the development of new fundamental insights and methodologies to exploit structural properties of...Measures One of the simplest class of dynamical networks that our proposed methodology can be explained in a simple setting is the class of first–order...developed a novel methodology to obtain tight lower and upper bounds for the class of systemic measures. In the following, some of the key ideas behind our

Dynamic assessment of bridge deck performance considering realistic bridge-traffic interaction : research brief

DOT National Transportation Integrated Search

2017-09-01

This study is to develop simulation methodology to conduct the dynamic assessment of bridge deck performance subjected to traffic. Concrete bridge decks are exposed to daily traffic loads and may experience some surface cracking caused by excessive s...

Towards a cognitive robotics methodology for reward-based decision-making: dynamical systems modelling of the Iowa Gambling Task

NASA Astrophysics Data System (ADS)

Lowe, Robert; Ziemke, Tom

2010-09-01

The somatic marker hypothesis (SMH) posits that the role of emotions and mental states in decision-making manifests through bodily responses to stimuli of import to the organism's welfare. The Iowa Gambling Task (IGT), proposed by Bechara and Damasio in the mid-1990s, has provided the major source of empirical validation to the role of somatic markers in the service of flexible and cost-effective decision-making in humans. In recent years the IGT has been the subject of much criticism concerning: (1) whether measures of somatic markers reveal that they are important for decision-making as opposed to behaviour preparation; (2) the underlying neural substrate posited as critical to decision-making of the type relevant to the task; and (3) aspects of the methodological approach used, particularly on the canonical version of the task. In this paper, a cognitive robotics methodology is proposed to explore a dynamical systems approach as it applies to the neural computation of reward-based learning and issues concerning embodiment. This approach is particularly relevant in light of a strongly emerging alternative hypothesis to the SMH, the reversal learning hypothesis, which links, behaviourally and neurocomputationally, a number of more or less complex reward-based decision-making tasks, including the 'A-not-B' task - already subject to dynamical systems investigations with a focus on neural activation dynamics. It is also suggested that the cognitive robotics methodology may be used to extend systematically the IGT benchmark to more naturalised, but nevertheless controlled, settings that might better explore the extent to which the SMH, and somatic states per se, impact on complex decision-making.

Clustering molecular dynamics trajectories for optimizing docking experiments.

PubMed

De Paris, Renata; Quevedo, Christian V; Ruiz, Duncan D; Norberto de Souza, Osmar; Barros, Rodrigo C

2015-01-01

Molecular dynamics simulations of protein receptors have become an attractive tool for rational drug discovery. However, the high computational cost of employing molecular dynamics trajectories in virtual screening of large repositories threats the feasibility of this task. Computational intelligence techniques have been applied in this context, with the ultimate goal of reducing the overall computational cost so the task can become feasible. Particularly, clustering algorithms have been widely used as a means to reduce the dimensionality of molecular dynamics trajectories. In this paper, we develop a novel methodology for clustering entire trajectories using structural features from the substrate-binding cavity of the receptor in order to optimize docking experiments on a cloud-based environment. The resulting partition was selected based on three clustering validity criteria, and it was further validated by analyzing the interactions between 20 ligands and a fully flexible receptor (FFR) model containing a 20 ns molecular dynamics simulation trajectory. Our proposed methodology shows that taking into account features of the substrate-binding cavity as input for the k-means algorithm is a promising technique for accurately selecting ensembles of representative structures tailored to a specific ligand.

A methodology for designing robust multivariable nonlinear control systems. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Grunberg, D. B.

1986-01-01

A new methodology is described for the design of nonlinear dynamic controllers for nonlinear multivariable systems providing guarantees of closed-loop stability, performance, and robustness. The methodology is an extension of the Linear-Quadratic-Gaussian with Loop-Transfer-Recovery (LQG/LTR) methodology for linear systems, thus hinging upon the idea of constructing an approximate inverse operator for the plant. A major feature of the methodology is a unification of both the state-space and input-output formulations. In addition, new results on stability theory, nonlinear state estimation, and optimal nonlinear regulator theory are presented, including the guaranteed global properties of the extended Kalman filter and optimal nonlinear regulators.

Nonadiabatic Dynamics of Photoinduced Proton-Coupled Electron Transfer Processes

DTIC Science & Technology

devices and photoelectrochemical cells. Theoretical methodology for simulating the nonadiabatic dynamics of photoinduced PCET reactions in solution has...tuning and control of the ultrafast dynamics is crucial for designing renewable and sustainable energy sources, such as artificial photosynthesis...describes the solute with a multiconfigurational method in a bath of explicit solvent molecules. The transferring hydrogen nucleus is represented as a

Young runoff fractions control streamwater age and solute concentration dynamics

Treesearch

Paolo Benettin; Scott W. Bailey; Andrea Rinaldo; Gene E. Likens; Kevin J. McGuire; Gianluca Botter

2017-01-01

We introduce a new representation of coupled solute and water age dynamics at the catchment scale, which shows how the contributions of young runoff waters can be directly referenced to observed water quality patterns. The methodology stems from recent trends in hydrologic transport that acknowledge the dynamic nature of streamflow age and explores the use of water age...

Thirteenth Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion and Launch Vehicle Technology. Volume 1

NASA Technical Reports Server (NTRS)

Williams, R. W. (Compiler)

1996-01-01

The purpose of the workshop was to discuss experimental and computational fluid dynamic activities in rocket propulsion and launch vehicles. The workshop was an open meeting for government, industry, and academia. A broad number of topics were discussed including computational fluid dynamic methodology, liquid and solid rocket propulsion, turbomachinery, combustion, heat transfer, and grid generation.

Measuring Group Work Dynamics and Its Relation with L2 Learners' Task Motivation and Language Production

ERIC Educational Resources Information Center

Poupore, Glen

2016-01-01

While learners of a second language (L2) are increasingly interacting in small groups as part of a communicative methodological paradigm, very few studies have investigated the social dynamics that occur in such groups. The aim of this study is to introduce a group work dynamic measuring instrument and to investigate the relationship between group…

Probabilistic assessment of dynamic system performance. Part 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belhadj, Mohamed

1993-01-01

Accurate prediction of dynamic system failure behavior can be important for the reliability and risk analyses of nuclear power plants, as well as for their backfitting to satisfy given constraints on overall system reliability, or optimization of system performance. Global analysis of dynamic systems through investigating the variations in the structure of the attractors of the system and the domains of attraction of these attractors as a function of the system parameters is also important for nuclear technology in order to understand the fault-tolerance as well as the safety margins of the system under consideration and to insure a safemore » operation of nuclear reactors. Such a global analysis would be particularly relevant to future reactors with inherent or passive safety features that are expected to rely on natural phenomena rather than active components to achieve and maintain safe shutdown. Conventionally, failure and global analysis of dynamic systems necessitate the utilization of different methodologies which have computational limitations on the system size that can be handled. Using a Chapman-Kolmogorov interpretation of system dynamics, a theoretical basis is developed that unifies these methodologies as special cases and which can be used for a comprehensive safety and reliability analysis of dynamic systems.« less

Lean vs Agile in the Context of Complexity Management in Organizations

ERIC Educational Resources Information Center

Putnik, Goran D.; Putnik, Zlata

2012-01-01

Purpose: The objective of this paper is to provide a deeper insight into the relationship of the issue "lean vs agile" in order to inform managers towards more coherent decisions especially in a dynamic, unpredictable, uncertain, non-linear environment. Design/methodology/approach: The methodology is an exploratory study based on secondary data…

Educational Strategies for Teaching Basic Family Dynamics to Non-Family Therapists.

ERIC Educational Resources Information Center

Merkel, William T.; Rudisill, John R.

1985-01-01

Presents six-part methodology for teaching basic concepts of family systems to non-family therapists and describes application of methodology to teach primary care physicians. Explains use of simulated encounters in which a physically symptomatic adolescent is interviewed alone, then with his mother, then with his whole family. (Author/NRB)

A Teacher Education for Sustainable Development System: An Institutional Responsibility

ERIC Educational Resources Information Center

Bentham, Hayley; Sinnes, Astrid; Gjøtterud, Sigrid

2015-01-01

Soft systems methodology is commonly used in organizational research and can be very useful when attempting to understand both organizational structures and dynamics. A teacher education institution is identified here as an organization. Soft systems methodology is employed to gain a picture of the current organizational structure of a Science and…

Mixing Qualitative and Quantitative Research in Developmental Science: Uses and Methodological Choices

ERIC Educational Resources Information Center

Yoshikawa, Hirokazu; Weisner, Thomas S.; Kalil, Ariel; Way, Niobe

2008-01-01

Multiple methods are vital to understanding development as a dynamic, transactional process. This article focuses on the ways in which quantitative and qualitative methodologies can be combined to enrich developmental science and the study of human development, focusing on the practical questions of "when" and "how." Research situations that may…

Research and development activities in unified control-structure modeling and design

NASA Technical Reports Server (NTRS)

Nayak, A. P.

1985-01-01

Results of work sponsored by JPL and other organizations to develop a unified control/structures modeling and design capability for large space structures is presented. Recent analytical results are presented to demonstrate the significant interdependence between structural and control properties. A new design methodology is suggested in which the structure, material properties, dynamic model and control design are all optimized simultaneously. The development of a methodology for global design optimization is recommended as a long term goal. It is suggested that this methodology should be incorporated into computer aided engineering programs, which eventually will be supplemented by an expert system to aid design optimization. Recommendations are also presented for near term research activities at JPL. The key recommendation is to continue the development of integrated dynamic modeling/control design techniques, with special attention given to the development of structural models specially tailored to support design.

Topology optimization for nonlinear dynamic problems: Considerations for automotive crashworthiness

NASA Astrophysics Data System (ADS)

Kaushik, Anshul; Ramani, Anand

2014-04-01

Crashworthiness of automotive structures is most often engineered after an optimal topology has been arrived at using other design considerations. This study is an attempt to incorporate crashworthiness requirements upfront in the topology synthesis process using a mathematically consistent framework. It proposes the use of equivalent linear systems from the nonlinear dynamic simulation in conjunction with a discrete-material topology optimizer. Velocity and acceleration constraints are consistently incorporated in the optimization set-up. Issues specific to crash problems due to the explicit solution methodology employed, nature of the boundary conditions imposed on the structure, etc. are discussed and possible resolutions are proposed. A demonstration of the methodology on two-dimensional problems that address some of the structural requirements and the types of loading typical of frontal and side impact is provided in order to show that this methodology has the potential for topology synthesis incorporating crashworthiness requirements.

Updating finite element dynamic models using an element-by-element sensitivity methodology

NASA Technical Reports Server (NTRS)

Farhat, Charbel; Hemez, Francois M.

1993-01-01

A sensitivity-based methodology for improving the finite element model of a given structure using test modal data and a few sensors is presented. The proposed method searches for both the location and sources of the mass and stiffness errors and does not interfere with the theory behind the finite element model while correcting these errors. The updating algorithm is derived from the unconstrained minimization of the squared L sub 2 norms of the modal dynamic residuals via an iterative two-step staggered procedure. At each iteration, the measured mode shapes are first expanded assuming that the model is error free, then the model parameters are corrected assuming that the expanded mode shapes are exact. The numerical algorithm is implemented in an element-by-element fashion and is capable of 'zooming' on the detected error locations. Several simulation examples which demonstate the potential of the proposed methodology are discussed.

Comparison of Damage Path Predictions for Composite Laminates by Explicit and Standard Finite Element Analysis Tools

NASA Technical Reports Server (NTRS)

Bogert, Philip B.; Satyanarayana, Arunkumar; Chunchu, Prasad B.

2006-01-01

Splitting, ultimate failure load and the damage path in center notched composite specimens subjected to in-plane tension loading are predicted using progressive failure analysis methodology. A 2-D Hashin-Rotem failure criterion is used in determining intra-laminar fiber and matrix failures. This progressive failure methodology has been implemented in the Abaqus/Explicit and Abaqus/Standard finite element codes through user written subroutines "VUMAT" and "USDFLD" respectively. A 2-D finite element model is used for predicting the intra-laminar damages. Analysis results obtained from the Abaqus/Explicit and Abaqus/Standard code show good agreement with experimental results. The importance of modeling delamination in progressive failure analysis methodology is recognized for future studies. The use of an explicit integration dynamics code for simple specimen geometry and static loading establishes a foundation for future analyses where complex loading and nonlinear dynamic interactions of damage and structure will necessitate it.

Adaptive optimization as a design and management methodology for coal-mining enterprise in uncertain and volatile market environment - the conceptual framework

NASA Astrophysics Data System (ADS)

Mikhalchenko, V. V.; Rubanik, Yu T.

2016-10-01

The work is devoted to the problem of cost-effective adaptation of coal mines to the volatile and uncertain market conditions. Conceptually it can be achieved through alignment of the dynamic characteristics of the coal mining system and power spectrum of market demand for coal product. In practical terms, this ensures the viability and competitiveness of coal mines. Transformation of dynamic characteristics is to be done by changing the structure of production system as well as corporate, logistics and management processes. The proposed methods and algorithms of control are aimed at the development of the theoretical foundations of adaptive optimization as basic methodology for coal mine enterprise management in conditions of high variability and uncertainty of economic and natural environment. Implementation of the proposed methodology requires a revision of the basic principles of open coal mining enterprises design.

Discrete Adjoint-Based Design for Unsteady Turbulent Flows On Dynamic Overset Unstructured Grids

NASA Technical Reports Server (NTRS)

Nielsen, Eric J.; Diskin, Boris

2012-01-01

A discrete adjoint-based design methodology for unsteady turbulent flows on three-dimensional dynamic overset unstructured grids is formulated, implemented, and verified. The methodology supports both compressible and incompressible flows and is amenable to massively parallel computing environments. The approach provides a general framework for performing highly efficient and discretely consistent sensitivity analysis for problems involving arbitrary combinations of overset unstructured grids which may be static, undergoing rigid or deforming motions, or any combination thereof. General parent-child motions are also accommodated, and the accuracy of the implementation is established using an independent verification based on a complex-variable approach. The methodology is used to demonstrate aerodynamic optimizations of a wind turbine geometry, a biologically-inspired flapping wing, and a complex helicopter configuration subject to trimming constraints. The objective function for each problem is successfully reduced and all specified constraints are satisfied.

Understanding system dynamics of an adaptive enzyme network from globally profiled kinetic parameters.

PubMed

Chiang, Austin W T; Liu, Wei-Chung; Charusanti, Pep; Hwang, Ming-Jing

2014-01-15

A major challenge in mathematical modeling of biological systems is to determine how model parameters contribute to systems dynamics. As biological processes are often complex in nature, it is desirable to address this issue using a systematic approach. Here, we propose a simple methodology that first performs an enrichment test to find patterns in the values of globally profiled kinetic parameters with which a model can produce the required system dynamics; this is then followed by a statistical test to elucidate the association between individual parameters and different parts of the system's dynamics. We demonstrate our methodology on a prototype biological system of perfect adaptation dynamics, namely the chemotaxis model for Escherichia coli. Our results agreed well with those derived from experimental data and theoretical studies in the literature. Using this model system, we showed that there are motifs in kinetic parameters and that these motifs are governed by constraints of the specified system dynamics. A systematic approach based on enrichment statistical tests has been developed to elucidate the relationships between model parameters and the roles they play in affecting system dynamics of a prototype biological network. The proposed approach is generally applicable and therefore can find wide use in systems biology modeling research.

A dynamic feedback-control toll pricing methodology : a case study on Interstate 95 managed lanes.

DOT National Transportation Integrated Search

2013-06-01

Recently, congestion pricing emerged as a cost-effective and efficient strategy to mitigate the congestion problem on freeways. This study develops a feedback-control based dynamic toll approach to formulate and solve for optimal tolls. The study com...

A novel simulation methodology merging source-sink dynamics and landscape connectivity

EPA Science Inventory

Source-sink dynamics are an emergent property of complex species-landscape interactions. This study explores the patterns of source and sink behavior that become established across a large landscape, using a simulation model for the northern spotted owl (Strix occidentalis cauri...

Safety of railroad passenger vehicle dynamics : OMNISIM simulation and test correlations for passenger rail cars

DOT National Transportation Integrated Search

2002-07-01

The purpose of the work is to validate the safety assessment methodology previously developed for passenger rail vehicle dynamics, which requires the application of simulation tools as well as testing of vehicles under different track scenarios. This...

Control Augmented Structural Synthesis

NASA Technical Reports Server (NTRS)

Lust, Robert V.; Schmit, Lucien A.

1988-01-01

A methodology for control augmented structural synthesis is proposed for a class of structures which can be modeled as an assemblage of frame and/or truss elements. It is assumed that both the plant (structure) and the active control system dynamics can be adequately represented with a linear model. The structural sizing variables, active control system feedback gains and nonstructural lumped masses are treated simultaneously as independent design variables. Design constraints are imposed on static and dynamic displacements, static stresses, actuator forces and natural frequencies to ensure acceptable system behavior. Multiple static and dynamic loading conditions are considered. Side constraints imposed on the design variables protect against the generation of unrealizable designs. While the proposed approach is fundamentally more general, here the methodology is developed and demonstrated for the case where: (1) the dynamic loading is harmonic and thus the steady state response is of primary interest; (2) direct output feedback is used for the control system model; and (3) the actuators and sensors are collocated.

A dynamic systems engineering methodology research study. Phase 2: Evaluating methodologies, tools, and techniques for applicability to NASA's systems projects

NASA Technical Reports Server (NTRS)

Paul, Arthur S.; Gill, Tepper L.; Maclin, Arlene P.

1989-01-01

A study of NASA's Systems Management Policy (SMP) concluded that the primary methodology being used by the Mission Operations and Data Systems Directorate and its subordinate, the Networks Division, is very effective. Still some unmet needs were identified. This study involved evaluating methodologies, tools, and techniques with the potential for resolving the previously identified deficiencies. Six preselected methodologies being used by other organizations with similar development problems were studied. The study revealed a wide range of significant differences in structure. Each system had some strengths but none will satisfy all of the needs of the Networks Division. Areas for improvement of the methodology being used by the Networks Division are listed with recommendations for specific action.

Dynamic task allocation for a man-machine symbiotic system

NASA Technical Reports Server (NTRS)

Parker, L. E.; Pin, F. G.

1987-01-01

This report presents a methodological approach to the dynamic allocation of tasks in a man-machine symbiotic system in the context of dexterous manipulation and teleoperation. This report addresses a symbiotic system containing two symbiotic partners which work toward controlling a single manipulator arm for the execution of a series of sequential manipulation tasks. It is proposed that an automated task allocator use knowledge about the constraints/criteria of the problem, the available resources, the tasks to be performed, and the environment to dynamically allocate task recommendations for the man and the machine. The presentation of the methodology includes discussions concerning the interaction of the knowledge areas, the flow of control, the necessary communication links, and the replanning of the task allocation. Examples of task allocation are presented to illustrate the results of this methodolgy.

Quadratic partial eigenvalue assignment in large-scale stochastic dynamic systems for resilient and economic design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, Sonjoy; Goswami, Kundan; Datta, Biswa N.

2014-12-10

Failure of structural systems under dynamic loading can be prevented via active vibration control which shifts the damped natural frequencies of the systems away from the dominant range of loading spectrum. The damped natural frequencies and the dynamic load typically show significant variations in practice. A computationally efficient methodology based on quadratic partial eigenvalue assignment technique and optimization under uncertainty has been formulated in the present work that will rigorously account for these variations and result in an economic and resilient design of structures. A novel scheme based on hierarchical clustering and importance sampling is also developed in this workmore » for accurate and efficient estimation of probability of failure to guarantee the desired resilience level of the designed system. Numerical examples are presented to illustrate the proposed methodology.« less

A New Real - Time Fault Detection Methodology for Systems Under Test. Phase 1

NASA Technical Reports Server (NTRS)

Johnson, Roger W.; Jayaram, Sanjay; Hull, Richard A.

1998-01-01

The purpose of this research is focussed on the identification/demonstration of critical technology innovations that will be applied to various applications viz. Detection of automated machine Health Monitoring (BM, real-time data analysis and control of Systems Under Test (SUT). This new innovation using a High Fidelity Dynamic Model-based Simulation (BFDMS) approach will be used to implement a real-time monitoring, Test and Evaluation (T&E) methodology including the transient behavior of the system under test. The unique element of this process control technique is the use of high fidelity, computer generated dynamic models to replicate the behavior of actual Systems Under Test (SUT). It will provide a dynamic simulation capability that becomes the reference truth model, from which comparisons are made with the actual raw/conditioned data from the test elements.

Contact Line Dynamics

NASA Astrophysics Data System (ADS)

Kreiss, Gunilla; Holmgren, Hanna; Kronbichler, Martin; Ge, Anthony; Brant, Luca

2017-11-01

The conventional no-slip boundary condition leads to a non-integrable stress singularity at a moving contact line. This makes numerical simulations of two-phase flow challenging, especially when capillarity of the contact point is essential for the dynamics of the flow. We will describe a modeling methodology, which is suitable for numerical simulations, and present results from numerical computations. The methodology is based on combining a relation between the apparent contact angle and the contact line velocity, with the similarity solution for Stokes flow at a planar interface. The relation between angle and velocity can be determined by theoretical arguments, or from simulations using a more detailed model. In our approach we have used results from phase field simulations in a small domain, but using a molecular dynamics model should also be possible. In both cases more physics is included and the stress singularity is removed.

Markov state models of protein misfolding

NASA Astrophysics Data System (ADS)

Sirur, Anshul; De Sancho, David; Best, Robert B.

2016-02-01

Markov state models (MSMs) are an extremely useful tool for understanding the conformational dynamics of macromolecules and for analyzing MD simulations in a quantitative fashion. They have been extensively used for peptide and protein folding, for small molecule binding, and for the study of native ensemble dynamics. Here, we adapt the MSM methodology to gain insight into the dynamics of misfolded states. To overcome possible flaws in root-mean-square deviation (RMSD)-based metrics, we introduce a novel discretization approach, based on coarse-grained contact maps. In addition, we extend the MSM methodology to include "sink" states in order to account for the irreversibility (on simulation time scales) of processes like protein misfolding. We apply this method to analyze the mechanism of misfolding of tandem repeats of titin domains, and how it is influenced by confinement in a chaperonin-like cavity.

The threshold algorithm: Description of the methodology and new developments

NASA Astrophysics Data System (ADS)

Neelamraju, Sridhar; Oligschleger, Christina; Schön, J. Christian

2017-10-01

Understanding the dynamics of complex systems requires the investigation of their energy landscape. In particular, the flow of probability on such landscapes is a central feature in visualizing the time evolution of complex systems. To obtain such flows, and the concomitant stable states of the systems and the generalized barriers among them, the threshold algorithm has been developed. Here, we describe the methodology of this approach starting from the fundamental concepts in complex energy landscapes and present recent new developments, the threshold-minimization algorithm and the molecular dynamics threshold algorithm. For applications of these new algorithms, we draw on landscape studies of three disaccharide molecules: lactose, maltose, and sucrose.

Direct Nanoscale Characterization of Submolecular Mobility in Complex Organic Non-linear Optical Systems

NASA Astrophysics Data System (ADS)

Knorr, Daniel; Gray, Tomoko; Kim, Tae-Dong; Luo, Jingdong; Jen, Alex; Overney, Rene

2008-03-01

For organic non-linear optical (NLO) materials composed of intricate molecular building blocks, the challenge is to deduce meaningful molecular scale mobility information to understand complex relaxation and phase behavior. This is crucial, as the process of achieving a robust acentric alignment strongly depends on the availability of inter- and intra-molecular mobilities outside the temperature range of the device operation window. Here, we introduce a nanoscale methodology based on scanning probe microscopy that provides direct insight into structural relaxations and shows great potential to direct material design of sophisticated macromolecules. It also offers a means by which mesoscale dynamics and cooperativity involved in relaxation processes can be quantified in terms of dynamic entropy and enthalpy. This study demonstrates this methodology to describe the mesocale dynamics of two systems (1) organic networking dendronized NLO molecular glasses that self-assemble into physically linked polymers due to quadrupolar phenyl-perfluorophenyl interactions and (2) dendronized side-chain electro-optic (EO) polymers. For the self assembling glasses, the degree of intermolecular cooperativity can be deduced using this methodology, while for the dendronized side-chain polymers, specific side chain mobilities are exploited to improve EO properties.

Methodological aspects of EEG and body dynamics measurements during motion

PubMed Central

Reis, Pedro M. R.; Hebenstreit, Felix; Gabsteiger, Florian; von Tscharner, Vinzenz; Lochmann, Matthias

2014-01-01

EEG involves the recording, analysis, and interpretation of voltages recorded on the human scalp which originate from brain gray matter. EEG is one of the most popular methods of studying and understanding the processes that underlie behavior. This is so, because EEG is relatively cheap, easy to wear, light weight and has high temporal resolution. In terms of behavior, this encompasses actions, such as movements that are performed in response to the environment. However, there are methodological difficulties which can occur when recording EEG during movement such as movement artifacts. Thus, most studies about the human brain have examined activations during static conditions. This article attempts to compile and describe relevant methodological solutions that emerged in order to measure body and brain dynamics during motion. These descriptions cover suggestions on how to avoid and reduce motion artifacts, hardware, software and techniques for synchronously recording EEG, EMG, kinematics, kinetics, and eye movements during motion. Additionally, we present various recording systems, EEG electrodes, caps and methods for determinating real/custom electrode positions. In the end we will conclude that it is possible to record and analyze synchronized brain and body dynamics related to movement or exercise tasks. PMID:24715858

Large scale nonlinear programming for the optimization of spacecraft trajectories

NASA Astrophysics Data System (ADS)

Arrieta-Camacho, Juan Jose

Despite the availability of high fidelity mathematical models, the computation of accurate optimal spacecraft trajectories has never been an easy task. While simplified models of spacecraft motion can provide useful estimates on energy requirements, sizing, and cost; the actual launch window and maneuver scheduling must rely on more accurate representations. We propose an alternative for the computation of optimal transfers that uses an accurate representation of the spacecraft dynamics. Like other methodologies for trajectory optimization, this alternative is able to consider all major disturbances. In contrast, it can handle explicitly equality and inequality constraints throughout the trajectory; it requires neither the derivation of costate equations nor the identification of the constrained arcs. The alternative consist of two steps: (1) discretizing the dynamic model using high-order collocation at Radau points, which displays numerical advantages, and (2) solution to the resulting Nonlinear Programming (NLP) problem using an interior point method, which does not suffer from the performance bottleneck associated with identifying the active set, as required by sequential quadratic programming methods; in this way the methodology exploits the availability of sound numerical methods, and next generation NLP solvers. In practice the methodology is versatile; it can be applied to a variety of aerospace problems like homing, guidance, and aircraft collision avoidance; the methodology is particularly well suited for low-thrust spacecraft trajectory optimization. Examples are presented which consider the optimization of a low-thrust orbit transfer subject to the main disturbances due to Earth's gravity field together with Lunar and Solar attraction. Other example considers the optimization of a multiple asteroid rendezvous problem. In both cases, the ability of our proposed methodology to consider non-standard objective functions and constraints is illustrated. Future research directions are identified, involving the automatic scheduling and optimization of trajectory correction maneuvers. The sensitivity information provided by the methodology is expected to be invaluable in such research pursuit. The collocation scheme and nonlinear programming algorithm presented in this work, complement other existing methodologies by providing reliable and efficient numerical methods able to handle large scale, nonlinear dynamic models.

Spatial and Temporal Evolution of Earthquake Dynamics: Case Study of the Mw 8.3 Illapel Earthquake, Chile

NASA Astrophysics Data System (ADS)

Yin, Jiuxun; Denolle, Marine A.; Yao, Huajian

2018-01-01

We develop a methodology that combines compressive sensing backprojection (CS-BP) and source spectral analysis of teleseismic P waves to provide metrics relevant to earthquake dynamics of large events. We improve the CS-BP method by an autoadaptive source grid refinement as well as a reference source adjustment technique to gain better spatial and temporal resolution of the locations of the radiated bursts. We also use a two-step source spectral analysis based on (i) simple theoretical Green's functions that include depth phases and water reverberations and on (ii) empirical P wave Green's functions. Furthermore, we propose a source spectrogram methodology that provides the temporal evolution of dynamic parameters such as radiated energy and falloff rates. Bridging backprojection and spectrogram analysis provides a spatial and temporal evolution of these dynamic source parameters. We apply our technique to the recent 2015 Mw 8.3 megathrust Illapel earthquake (Chile). The results from both techniques are consistent and reveal a depth-varying seismic radiation that is also found in other megathrust earthquakes. The low-frequency content of the seismic radiation is located in the shallow part of the megathrust, propagating unilaterally from the hypocenter toward the trench while most of the high-frequency content comes from the downdip part of the fault. Interpretation of multiple rupture stages in the radiation is also supported by the temporal variations of radiated energy and falloff rates. Finally, we discuss the possible mechanisms, either from prestress, fault geometry, and/or frictional properties to explain our observables. Our methodology is an attempt to bridge kinematic observations with earthquake dynamics.

A novel statistical methodology to overcome sampling irregularities in the forest inventory data and to model forest changes under dynamic disturbance regimes

Treesearch

Nikolay Strigul; Jean Lienard

2015-01-01

Forest inventory datasets offer unprecedented opportunities to model forest dynamics under evolving environmental conditions but they are analytically challenging due to irregular sampling time intervals of the same plot, across the years. We propose here a novel method to model dynamic changes in forest biomass and basal area using forest inventory data. Our...

Combat Simulation Using Breach Computer Language

DTIC Science & Technology

1979-09-01

simulation and weapon system analysis computer language Two types of models were constructed: a stochastic duel and a dynamic engagement model The... duel model validates the BREACH approach by comparing results with mathematical solutions. The dynamic model shows the capability of the BREACH...BREACH 2 Background 2 The Language 3 Static Duel 4 Background and Methodology 4 Validation 5 Results 8 Tank Duel Simulation 8 Dynamic Assault Model

Free-Energy Profiles of Membrane Insertion of the M2 Transmembrane Peptide from Influenza A Virus

DTIC Science & Technology

2008-12-01

ABSTRACT The insertion of the M2 transmembrane peptide from influenza A virus into a membrane has been studied with molecular - dynamics simulations ...performed replica-exchange molecular - dynamics simulations with umbrella-sampling techniques to characterize the probability distribution and conformation...atomic- detailed molecular dynamics (MD) simulation techniques represent a valuable complementary methodology to inves- tigate membrane-insertion of

External Dynamics Influencing Tattooing among College Students: A Qualitative Analysis

ERIC Educational Resources Information Center

Firmin, Michael; Tse, Luke; Foster, Janna; Angelini, Tammy

2012-01-01

The study utilized qualitative research methodology to assess external dynamics and their influences on tattooing practices among college students. Twenty-four undergraduates supplied in-depth interviews regarding the external variables related to college students' decisions to tattoo. The present research follows (Tse, Firmin, Angelini, &…

Object Oriented Learning Objects

ERIC Educational Resources Information Center

Morris, Ed

2005-01-01

We apply the object oriented software engineering (OOSE) design methodology for software objects (SOs) to learning objects (LOs). OOSE extends and refines design principles for authoring dynamic reusable LOs. Our learning object class (LOC) is a template from which individualised LOs can be dynamically created for, or by, students. The properties…

A hybrid system identification methodology for wireless structural health monitoring systems based on dynamic substructuring

NASA Astrophysics Data System (ADS)

Dragos, Kosmas; Smarsly, Kay

2016-04-01

System identification has been employed in numerous structural health monitoring (SHM) applications. Traditional system identification methods usually rely on centralized processing of structural response data to extract information on structural parameters. However, in wireless SHM systems the centralized processing of structural response data introduces a significant communication bottleneck. Exploiting the merits of decentralization and on-board processing power of wireless SHM systems, many system identification methods have been successfully implemented in wireless sensor networks. While several system identification approaches for wireless SHM systems have been proposed, little attention has been paid to obtaining information on the physical parameters (e.g. stiffness, damping) of the monitored structure. This paper presents a hybrid system identification methodology suitable for wireless sensor networks based on the principles of component mode synthesis (dynamic substructuring). A numerical model of the monitored structure is embedded into the wireless sensor nodes in a distributed manner, i.e. the entire model is segmented into sub-models, each embedded into one sensor node corresponding to the substructure the sensor node is assigned to. The parameters of each sub-model are estimated by extracting local mode shapes and by applying the equations of the Craig-Bampton method on dynamic substructuring. The proposed methodology is validated in a laboratory test conducted on a four-story frame structure to demonstrate the ability of the methodology to yield accurate estimates of stiffness parameters. Finally, the test results are discussed and an outlook on future research directions is provided.

A Dynamic System Approach to Willingness to Communicate: Developing an Idiodynamic Method to Capture Rapidly Changing Affect

ERIC Educational Resources Information Center

Macintyre, Peter D.; Legatto, James Jason

2011-01-01

Willingness to communicate (WTC) can be conceptualized as changing from moment to moment, as opportunities for second-language communication arise. In this study we present an idiodynamic methodology for studying rapid changes in WTC. The methodology consists of recording responses from six young adult, female speakers to second-language…

A methodology for the assessment of manned flight simulator fidelity

NASA Technical Reports Server (NTRS)

Hess, Ronald A.; Malsbury, Terry N.

1989-01-01

A relatively simple analytical methodology for assessing the fidelity of manned flight simulators for specific vehicles and tasks is offered. The methodology is based upon an application of a structural model of the human pilot, including motion cue effects. In particular, predicted pilot/vehicle dynamic characteristics are obtained with and without simulator limitations. A procedure for selecting model parameters can be implemented, given a probable pilot control strategy. In analyzing a pair of piloting tasks for which flight and simulation data are available, the methodology correctly predicted the existence of simulator fidelity problems. The methodology permitted the analytical evaluation of a change in simulator characteristics and indicated that a major source of the fidelity problems was a visual time delay in the simulation.

DSN model for use in strategic planning

NASA Technical Reports Server (NTRS)

Kelly, K. C.; Lin, C. Y.; Mckenzie, M.

1981-01-01

A System Dynamics Model of the DSN to support strategic planning for the Network is addressed. Applications for the model are described, as well as the foundations of system dynamics and the methodology used to develop the model. Activities to date and plans for future work are also discussed.

The Social Dynamics of Art Research: Contemporary Photography in Belfast Post the Good Friday Agreement

ERIC Educational Resources Information Center

Tuck, Sarah

2014-01-01

This article reflects critically on "The Social Dynamics of Art Research: Contemporary Photography in Belfast", an engaged research project conducted with photographers, community activists, academics and visual artists in Belfast. Through a critical examination of the project's theoretical architecture and methodological framework this…

Methodology in the assessment of complex human performance : the effects of signal rate on monitoring a dynamic process.

DOT National Transportation Integrated Search

1969-04-01

Male subjects were tested after extensive training as two five-man 'crews' in an experiment designed to examine the effects of signal rate on the performance of a task involving the monitoring of a dynamic process. Performance was measured using thre...

The Dynamics of Information Search Services.

ERIC Educational Resources Information Center

Lindquist, Mats G.

Computer-based information search services (ISSs) of the type that provide online literature searches are analyzed from a systems viewpoint using a continuous simulation model. The methodology applied is "system dynamics," and the system language is DYNAMO. The analysis reveals that the observed growth and stagnation of a typical ISS can…

A review of gear housing dynamics and acoustics literature

NASA Technical Reports Server (NTRS)

Singh, Rajendra; Lim, Teik Chin

1988-01-01

A review of the available literature on gear housing vibration and noise reduction is presented. Analytical and experimental methodologies used for bearing dynamics, housing vibration and noise, mounts and suspensions, and the overall geared and housing system are discussed. Typical design guidelines as outlined by various investigators are given.

Gamma ray observatory dynamics simulator in Ada (GRODY)

NASA Technical Reports Server (NTRS)

1990-01-01

This experiment involved the parallel development of dynamics simulators for the Gamma Ray Observatory in both FORTRAN and Ada for the purpose of evaluating the applicability of Ada to the NASA/Goddard Space Flight Center's flight dynamics environment. The experiment successfully demonstrated that Ada is a viable, valuable technology for use in this environment. In addition to building a simulator, the Ada team evaluated training approaches, developed an Ada methodology appropriate to the flight dynamics environment, and established a baseline for evaluating future Ada projects.

Brownian dynamics simulation of protein diffusion in crowded environments

NASA Astrophysics Data System (ADS)

Mereghetti, Paolo; Wade, Rebecca C.

2013-02-01

High macromolecular concentrations are a distinguishing feature of living organisms. Understanding how the high concentration of solutes affects the dynamic properties of biological macromolecules is fundamental for the comprehension of biological processes in living systems. We first describe the development of a Brownian dynamics simulation methodology to investigate the dynamic and structural properties of protein solutions using atomic-detail protein structures. We then discuss insights obtained from applying this approach to simulation of solutions of a range of types of proteins.

Solar Dynamics Observatory (SDO) HGAS Induced Jitter

NASA Technical Reports Server (NTRS)

Liu, Alice; Blaurock, Carl; Liu, Kuo-Chia; Mule, Peter

2008-01-01

This paper presents the results of a comprehensive assessment of High Gain Antenna System induced jitter on the Solar Dynamics Observatory. The jitter prediction is created using a coupled model of the structural dynamics, optical response, control systems, and stepper motor actuator electromechanical dynamics. The paper gives an overview of the model components, presents the verification processes used to evaluate the models, describes validation and calibration tests and model-to-measurement comparison results, and presents the jitter analysis methodology and results.

TOWARDS A MULTI-SCALE AGENT-BASED PROGRAMMING LANGUAGE METHODOLOGY

PubMed Central

Somogyi, Endre; Hagar, Amit; Glazier, James A.

2017-01-01

Living tissues are dynamic, heterogeneous compositions of objects, including molecules, cells and extra-cellular materials, which interact via chemical, mechanical and electrical process and reorganize via transformation, birth, death and migration processes. Current programming language have difficulty describing the dynamics of tissues because: 1: Dynamic sets of objects participate simultaneously in multiple processes, 2: Processes may be either continuous or discrete, and their activity may be conditional, 3: Objects and processes form complex, heterogeneous relationships and structures, 4: Objects and processes may be hierarchically composed, 5: Processes may create, destroy and transform objects and processes. Some modeling languages support these concepts, but most cannot translate models into executable simulations. We present a new hybrid executable modeling language paradigm, the Continuous Concurrent Object Process Methodology (CCOPM) which naturally expresses tissue models, enabling users to visually create agent-based models of tissues, and also allows computer simulation of these models. PMID:29282379

TOWARDS A MULTI-SCALE AGENT-BASED PROGRAMMING LANGUAGE METHODOLOGY.

PubMed

Somogyi, Endre; Hagar, Amit; Glazier, James A

2016-12-01

Living tissues are dynamic, heterogeneous compositions of objects , including molecules, cells and extra-cellular materials, which interact via chemical, mechanical and electrical process and reorganize via transformation, birth, death and migration processes . Current programming language have difficulty describing the dynamics of tissues because: 1: Dynamic sets of objects participate simultaneously in multiple processes, 2: Processes may be either continuous or discrete, and their activity may be conditional, 3: Objects and processes form complex, heterogeneous relationships and structures, 4: Objects and processes may be hierarchically composed, 5: Processes may create, destroy and transform objects and processes. Some modeling languages support these concepts, but most cannot translate models into executable simulations. We present a new hybrid executable modeling language paradigm, the Continuous Concurrent Object Process Methodology ( CCOPM ) which naturally expresses tissue models, enabling users to visually create agent-based models of tissues, and also allows computer simulation of these models.

Application of Control Volume Analysis to Cerebrospinal Fluid Dynamics

NASA Astrophysics Data System (ADS)

Wei, Timothy; Cohen, Benjamin; Anor, Tomer; Madsen, Joseph

2011-11-01

Hydrocephalus is among the most common birth defects and may not be prevented nor cured. Afflicted individuals face serious issues, which at present are too complicated and not well enough understood to treat via systematic therapies. This talk outlines the framework and application of a control volume methodology to clinical Phase Contrast MRI data. Specifically, integral control volume analysis utilizes a fundamental, fluid dynamics methodology to quantify intracranial dynamics within a precise, direct, and physically meaningful framework. A chronically shunted, hydrocephalic patient in need of a revision procedure was used as an in vivo case study. Magnetic resonance velocity measurements within the patient's aqueduct were obtained in four biomedical state and were analyzed using the methods presented in this dissertation. Pressure force estimates were obtained, showing distinct differences in amplitude, phase, and waveform shape for different intracranial states within the same individual. Thoughts on the physiological and diagnostic research and development implications/opportunities will be presented.

gr-MRI: A software package for magnetic resonance imaging using software defined radios

NASA Astrophysics Data System (ADS)

Hasselwander, Christopher J.; Cao, Zhipeng; Grissom, William A.

2016-09-01

The goal of this work is to develop software that enables the rapid implementation of custom MRI spectrometers using commercially-available software defined radios (SDRs). The developed gr-MRI software package comprises a set of Python scripts, flowgraphs, and signal generation and recording blocks for GNU Radio, an open-source SDR software package that is widely used in communications research. gr-MRI implements basic event sequencing functionality, and tools for system calibrations, multi-radio synchronization, and MR signal processing and image reconstruction. It includes four pulse sequences: a single-pulse sequence to record free induction signals, a gradient-recalled echo imaging sequence, a spin echo imaging sequence, and an inversion recovery spin echo imaging sequence. The sequences were used to perform phantom imaging scans with a 0.5 Tesla tabletop MRI scanner and two commercially-available SDRs. One SDR was used for RF excitation and reception, and the other for gradient pulse generation. The total SDR hardware cost was approximately 2000. The frequency of radio desynchronization events and the frequency with which the software recovered from those events was also measured, and the SDR's ability to generate frequency-swept RF waveforms was validated and compared to the scanner's commercial spectrometer. The spin echo images geometrically matched those acquired using the commercial spectrometer, with no unexpected distortions. Desynchronization events were more likely to occur at the very beginning of an imaging scan, but were nearly eliminated if the user invoked the sequence for a short period before beginning data recording. The SDR produced a 500 kHz bandwidth frequency-swept pulse with high fidelity, while the commercial spectrometer produced a waveform with large frequency spike errors. In conclusion, the developed gr-MRI software can be used to develop high-fidelity, low-cost custom MRI spectrometers using commercially-available SDRs.

MPEG-1 low-cost encoder solution

NASA Astrophysics Data System (ADS)

Grueger, Klaus; Schirrmeister, Frank; Filor, Lutz; von Reventlow, Christian; Schneider, Ulrich; Mueller, Gerriet; Sefzik, Nicolai; Fiedrich, Sven

1995-02-01

A solution for real-time compression of digital YCRCB video data to an MPEG-1 video data stream has been developed. As an additional option, motion JPEG and video telephone streams (H.261) can be generated. For MPEG-1, up to two bidirectional predicted images are supported. The required computational power for motion estimation and DCT/IDCT, memory size and memory bandwidth have been the main challenges. The design uses fast-page-mode memory accesses and requires only one single 80 ns EDO-DRAM with 256 X 16 organization for video encoding. This can be achieved only by using adequate access and coding strategies. The architecture consists of an input processing and filter unit, a memory interface, a motion estimation unit, a motion compensation unit, a DCT unit, a quantization control, a VLC unit and a bus interface. For using the available memory bandwidth by the processing tasks, a fixed schedule for memory accesses has been applied, that can be interrupted for asynchronous events. The motion estimation unit implements a highly sophisticated hierarchical search strategy based on block matching. The DCT unit uses a separated fast-DCT flowgraph realized by a switchable hardware unit for both DCT and IDCT operation. By appropriate multiplexing, only one multiplier is required for: DCT, quantization, inverse quantization, and IDCT. The VLC unit generates the video-stream up to the video sequence layer and is directly coupled with an intelligent bus-interface. Thus, the assembly of video, audio and system data can easily be performed by the host computer. Having a relatively low complexity and only small requirements for DRAM circuits, the developed solution can be applied to low-cost encoding products for consumer electronics.

Upper limb joint forces and moments during underwater cyclical movements.

PubMed

Lauer, Jessy; Rouard, Annie Hélène; Vilas-Boas, João Paulo

2016-10-03

Sound inverse dynamics modeling is lacking in aquatic locomotion research because of the difficulty in measuring hydrodynamic forces in dynamic conditions. Here we report the successful implementation and validation of an innovative methodology crossing new computational fluid dynamics and inverse dynamics techniques to quantify upper limb joint forces and moments while moving in water. Upper limb kinematics of seven male swimmers sculling while ballasted with 4kg was recorded through underwater motion capture. Together with body scans, segment inertial properties, and hydrodynamic resistances computed from a unique dynamic mesh algorithm capable to handle large body deformations, these data were fed into an inverse dynamics model to solve for joint kinetics. Simulation validity was assessed by comparing the impulse produced by the arms, calculated by integrating vertical forces over a stroke period, to the net theoretical impulse of buoyancy and ballast forces. A resulting gap of 1.2±3.5% provided confidence in the results. Upper limb joint load was within 5% of swimmer׳s body weight, which tends to supports the use of low-load aquatic exercises to reduce joint stress. We expect this significant methodological improvement to pave the way towards deeper insights into the mechanics of aquatic movement and the establishment of practice guidelines in rehabilitation, fitness or swimming performance. Copyright © 2016 Elsevier Ltd. All rights reserved.

Clustering Molecular Dynamics Trajectories for Optimizing Docking Experiments

PubMed Central

De Paris, Renata; Quevedo, Christian V.; Ruiz, Duncan D.; Norberto de Souza, Osmar; Barros, Rodrigo C.

2015-01-01

Molecular dynamics simulations of protein receptors have become an attractive tool for rational drug discovery. However, the high computational cost of employing molecular dynamics trajectories in virtual screening of large repositories threats the feasibility of this task. Computational intelligence techniques have been applied in this context, with the ultimate goal of reducing the overall computational cost so the task can become feasible. Particularly, clustering algorithms have been widely used as a means to reduce the dimensionality of molecular dynamics trajectories. In this paper, we develop a novel methodology for clustering entire trajectories using structural features from the substrate-binding cavity of the receptor in order to optimize docking experiments on a cloud-based environment. The resulting partition was selected based on three clustering validity criteria, and it was further validated by analyzing the interactions between 20 ligands and a fully flexible receptor (FFR) model containing a 20 ns molecular dynamics simulation trajectory. Our proposed methodology shows that taking into account features of the substrate-binding cavity as input for the k-means algorithm is a promising technique for accurately selecting ensembles of representative structures tailored to a specific ligand. PMID:25873944

Algorithm for cellular reprogramming.

PubMed

Ronquist, Scott; Patterson, Geoff; Muir, Lindsey A; Lindsly, Stephen; Chen, Haiming; Brown, Markus; Wicha, Max S; Bloch, Anthony; Brockett, Roger; Rajapakse, Indika

2017-11-07

The day we understand the time evolution of subcellular events at a level of detail comparable to physical systems governed by Newton's laws of motion seems far away. Even so, quantitative approaches to cellular dynamics add to our understanding of cell biology. With data-guided frameworks we can develop better predictions about, and methods for, control over specific biological processes and system-wide cell behavior. Here we describe an approach for optimizing the use of transcription factors (TFs) in cellular reprogramming, based on a device commonly used in optimal control. We construct an approximate model for the natural evolution of a cell-cycle-synchronized population of human fibroblasts, based on data obtained by sampling the expression of 22,083 genes at several time points during the cell cycle. To arrive at a model of moderate complexity, we cluster gene expression based on division of the genome into topologically associating domains (TADs) and then model the dynamics of TAD expression levels. Based on this dynamical model and additional data, such as known TF binding sites and activity, we develop a methodology for identifying the top TF candidates for a specific cellular reprogramming task. Our data-guided methodology identifies a number of TFs previously validated for reprogramming and/or natural differentiation and predicts some potentially useful combinations of TFs. Our findings highlight the immense potential of dynamical models, mathematics, and data-guided methodologies for improving strategies for control over biological processes. Copyright © 2017 the Author(s). Published by PNAS.

Simulating large-scale pedestrian movement using CA and event driven model: Methodology and case study

NASA Astrophysics Data System (ADS)

Li, Jun; Fu, Siyao; He, Haibo; Jia, Hongfei; Li, Yanzhong; Guo, Yi

2015-11-01

Large-scale regional evacuation is an important part of national security emergency response plan. Large commercial shopping area, as the typical service system, its emergency evacuation is one of the hot research topics. A systematic methodology based on Cellular Automata with the Dynamic Floor Field and event driven model has been proposed, and the methodology has been examined within context of a case study involving the evacuation within a commercial shopping mall. Pedestrians walking is based on Cellular Automata and event driven model. In this paper, the event driven model is adopted to simulate the pedestrian movement patterns, the simulation process is divided into normal situation and emergency evacuation. The model is composed of four layers: environment layer, customer layer, clerk layer and trajectory layer. For the simulation of movement route of pedestrians, the model takes into account purchase intention of customers and density of pedestrians. Based on evacuation model of Cellular Automata with Dynamic Floor Field and event driven model, we can reflect behavior characteristics of customers and clerks at the situations of normal and emergency evacuation. The distribution of individual evacuation time as a function of initial positions and the dynamics of the evacuation process is studied. Our results indicate that the evacuation model using the combination of Cellular Automata with Dynamic Floor Field and event driven scheduling can be used to simulate the evacuation of pedestrian flows in indoor areas with complicated surroundings and to investigate the layout of shopping mall.

The Influence of Power Shifts in Data Collection and Analysis Stages: A Focus on Qualitative Research Interview

ERIC Educational Resources Information Center

Anyan, Frederick

2013-01-01

This paper analyzes the power relation between the interviewer and the interviewee in the qualitative research interview methodology. The paper sets out to grapple with the extent to which the dynamisms in power shifts influence data collection and analysis in the interview methodology. The exploration of power shifts in the qualitative research…

CFD Analysis of the SBXC Glider Airframe

DTIC Science & Technology

2016-06-01

mathematically on finite element methods. To validate and verify the methodology developed, a mathematical comparison was made with the previous research data...greater than 15 m/s. 14. SUBJECT TERMS finite element method, computational fluid dynamics, Y Plus, mesh element quality, aerodynamic data, fluid...based mathematically on finite element methods. To validate and verify the methodology developed, a mathematical comparison was made with the

"A Day in the Life": Advancing a Methodology for the Cultural Study of Development and Learning in Early Childhood

ERIC Educational Resources Information Center

Gillen, Julia; Cameron, Catherine Ann; Tapanya, Sombat; Pinto, Giuliana; Hancock, Roger; Young, Susan; Gamannossi, Beatrice Accorti

2007-01-01

This paper explores the methodology of an ecological investigation of aspects of culture in the interactional construction of early childhood in diverse global communities: Peru, Italy, Canada, Thailand, and the United Kingdom. Regarding culture as a dynamic dimension of the child's socialisation, the approach taken was to film a "day in the…

Near ground level sensing for spatial analysis of vegetation

NASA Technical Reports Server (NTRS)

Sauer, Tom; Rasure, John; Gage, Charlie

1991-01-01

Measured changes in vegetation indicate the dynamics of ecological processes and can identify the impacts from disturbances. Traditional methods of vegetation analysis tend to be slow because they are labor intensive; as a result, these methods are often confined to small local area measurements. Scientists need new algorithms and instruments that will allow them to efficiently study environmental dynamics across a range of different spatial scales. A new methodology that addresses this problem is presented. This methodology includes the acquisition, processing, and presentation of near ground level image data and its corresponding spatial characteristics. The systematic approach taken encompasses a feature extraction process, a supervised and unsupervised classification process, and a region labeling process yielding spatial information.

An approach to software cost estimation

NASA Technical Reports Server (NTRS)

Mcgarry, F.; Page, J.; Card, D.; Rohleder, M.; Church, V.

1984-01-01

A general procedure for software cost estimation in any environment is outlined. The basic concepts of work and effort estimation are explained, some popular resource estimation models are reviewed, and the accuracy of source estimates is discussed. A software cost prediction procedure based on the experiences of the Software Engineering Laboratory in the flight dynamics area and incorporating management expertise, cost models, and historical data is described. The sources of information and relevant parameters available during each phase of the software life cycle are identified. The methodology suggested incorporates these elements into a customized management tool for software cost prediction. Detailed guidelines for estimation in the flight dynamics environment developed using this methodology are presented.

Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design

PubMed Central

Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

2015-01-01

The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms. PMID:25583870

Requirements analysis notebook for the flight data systems definition in the Real-Time Systems Engineering Laboratory (RSEL)

NASA Astrophysics Data System (ADS)

Wray, Richard B.

1991-12-01

A hybrid requirements analysis methodology was developed, based on the practices actually used in developing a Space Generic Open Avionics Architecture. During the development of this avionics architecture, a method of analysis able to effectively define the requirements for this space avionics architecture was developed. In this methodology, external interfaces and relationships are defined, a static analysis resulting in a static avionics model was developed, operating concepts for simulating the requirements were put together, and a dynamic analysis of the execution needs for the dynamic model operation was planned. The systems engineering approach was used to perform a top down modified structured analysis of a generic space avionics system and to convert actual program results into generic requirements. CASE tools were used to model the analyzed system and automatically generate specifications describing the model's requirements. Lessons learned in the use of CASE tools, the architecture, and the design of the Space Generic Avionics model were established, and a methodology notebook was prepared for NASA. The weaknesses of standard real-time methodologies for practicing systems engineering, such as Structured Analysis and Object Oriented Analysis, were identified.

Control Law Design in a Computational Aeroelasticity Environment

NASA Technical Reports Server (NTRS)

Newsom, Jerry R.; Robertshaw, Harry H.; Kapania, Rakesh K.

2003-01-01

A methodology for designing active control laws in a computational aeroelasticity environment is given. The methodology involves employing a systems identification technique to develop an explicit state-space model for control law design from the output of a computational aeroelasticity code. The particular computational aeroelasticity code employed in this paper solves the transonic small disturbance aerodynamic equation using a time-accurate, finite-difference scheme. Linear structural dynamics equations are integrated simultaneously with the computational fluid dynamics equations to determine the time responses of the structure. These structural responses are employed as the input to a modern systems identification technique that determines the Markov parameters of an "equivalent linear system". The Eigensystem Realization Algorithm is then employed to develop an explicit state-space model of the equivalent linear system. The Linear Quadratic Guassian control law design technique is employed to design a control law. The computational aeroelasticity code is modified to accept control laws and perform closed-loop simulations. Flutter control of a rectangular wing model is chosen to demonstrate the methodology. Various cases are used to illustrate the usefulness of the methodology as the nonlinearity of the aeroelastic system is increased through increased angle-of-attack changes.

Requirements analysis notebook for the flight data systems definition in the Real-Time Systems Engineering Laboratory (RSEL)

NASA Technical Reports Server (NTRS)

Wray, Richard B.

1991-01-01

A hybrid requirements analysis methodology was developed, based on the practices actually used in developing a Space Generic Open Avionics Architecture. During the development of this avionics architecture, a method of analysis able to effectively define the requirements for this space avionics architecture was developed. In this methodology, external interfaces and relationships are defined, a static analysis resulting in a static avionics model was developed, operating concepts for simulating the requirements were put together, and a dynamic analysis of the execution needs for the dynamic model operation was planned. The systems engineering approach was used to perform a top down modified structured analysis of a generic space avionics system and to convert actual program results into generic requirements. CASE tools were used to model the analyzed system and automatically generate specifications describing the model's requirements. Lessons learned in the use of CASE tools, the architecture, and the design of the Space Generic Avionics model were established, and a methodology notebook was prepared for NASA. The weaknesses of standard real-time methodologies for practicing systems engineering, such as Structured Analysis and Object Oriented Analysis, were identified.

One Controller at a Time (1-CAT): A mimo design methodology

NASA Technical Reports Server (NTRS)

Mitchell, J. R.; Lucas, J. C.

1987-01-01

The One Controller at a Time (1-CAT) methodology for designing digital controllers for Large Space Structures (LSS's) is introduced and illustrated. The flexible mode problem is first discussed. Next, desirable features of a LSS control system design methodology are delineated. The 1-CAT approach is presented, along with an analytical technique for carrying out the 1-CAT process. Next, 1-CAT is used to design digital controllers for the proposed Space Based Laser (SBL). Finally, the SBL design is evaluated for dynamical performance, noise rejection, and robustness.

Developpement d'une plateforme de simulation et d'un pilote automatique - Application aux Cessna Citation X et Hawker 800XP

NASA Astrophysics Data System (ADS)

Ghazi, Georges

This report presents several methodologies for the design of tools intended to the analysis of the stability and the control of a business aircraft. At first, a generic flight dynamic model was developed to predict the behavior of the aircraft further to a movement on the control surfaces or further to any disturbance. For that purpose, different categories of winds were considered in the module of simulation to generate various scenarios and conclude about the efficiency of the autopilot. Besides being realistic, the flight model takes into account the variation of the mass parameters according to fuel consumption. A comparison with a simulator of the company CAE Inc. and certified level D allowed to validate this first stage with an acceptable success rate. Once the dynamics is validated, the next stage deals with the stability around a flight condition. For that purpose, a first static analysis is established to find the trim conditions inside the flight envelop. Then, two algorithms of linearization generate the state space models which approximate the decoupled dynamics (longitudinal and lateral) of the aircraft. Then to test the viability of the linear models, 1,500 comparisons with the nonlinear dynamics have been done with a 100% rate of success. The study of stability allowed to highlight the need of control systems to improve first the performances of the plane, then to control its different axes. A methodology based on a coupling between a modern control technique (LQR) and a genetic algorithm is presented. This methodology allowed to find optimal and successful controllers which satisfy a large number of specifications. Besides being successful, they have to be robust to uncertainties owed to the variation of mass. Thus, an analysis of robustness using the theory of the guardian maps was applied to uncertain dynamics. However, because of a too sensitive region of the flight envelop, some analyses are biased. Nevertheless, a validation with the nonlinear dynamics allowed to prove the robustness of the controllers over the entire flight envelope. Finally, the last stage of this project concerned the control laws for the autopilot. Once again, the proposed methodology, bases itself on the association of flight mechanic equations, control theory and a metaheuristic optimization method. Afterward, four detailed test scenarios are presented to illustrate the efficiency and the robustness of the entire autopilot.

A methodology for creating greenways through multidisciplinary sustainable landscape planning.

PubMed

Pena, Selma Beatriz; Abreu, Maria Manuela; Teles, Rui; Espírito-Santo, Maria Dalila

2010-01-01

This research proposes a methodology for defining greenways via sustainable planning. This approach includes the analysis and discussion of culture and natural processes that occur in the landscape. The proposed methodology is structured in three phases: eco-cultural analysis; synthesis and diagnosis; and proposal. An interdisciplinary approach provides an assessment of the relationships between landscape structure and landscape dynamics, which are essential to any landscape management or land use. The landscape eco-cultural analysis provides a biophysical, dynamic (geomorphologic rate), vegetation (habitats from directive 92/43/EEC) and cultural characterisation. The knowledge obtained by this analysis then supports the definition of priority actions to stabilise the landscape and the management measures for the habitats. After the analysis and diagnosis phases, a proposal for the development of sustainable greenways can be achieved. This methodology was applied to a study area of the Azambuja Municipality in the Lisbon Metropolitan Area (Portugal). The application of the proposed methodology to the study area shows that landscape stability is crucial for greenway users in order to appreciate the landscape and its natural and cultural elements in a sustainable and healthy way, both by cycling or by foot. A balanced landscape will increase the value of greenways and in return, they can develop socio-economic activities with benefits for rural communities. Copyright 2009 Elsevier Ltd. All rights reserved.

A Security Assessment Mechanism for Software-Defined Networking-Based Mobile Networks.

PubMed

Luo, Shibo; Dong, Mianxiong; Ota, Kaoru; Wu, Jun; Li, Jianhua

2015-12-17

Software-Defined Networking-based Mobile Networks (SDN-MNs) are considered the future of 5G mobile network architecture. With the evolving cyber-attack threat, security assessments need to be performed in the network management. Due to the distinctive features of SDN-MNs, such as their dynamic nature and complexity, traditional network security assessment methodologies cannot be applied directly to SDN-MNs, and a novel security assessment methodology is needed. In this paper, an effective security assessment mechanism based on attack graphs and an Analytic Hierarchy Process (AHP) is proposed for SDN-MNs. Firstly, this paper discusses the security assessment problem of SDN-MNs and proposes a methodology using attack graphs and AHP. Secondly, to address the diversity and complexity of SDN-MNs, a novel attack graph definition and attack graph generation algorithm are proposed. In order to quantify security levels, the Node Minimal Effort (NME) is defined to quantify attack cost and derive system security levels based on NME. Thirdly, to calculate the NME of an attack graph that takes the dynamic factors of SDN-MN into consideration, we use AHP integrated with the Technique for Order Preference by Similarity to an Ideal Solution (TOPSIS) as the methodology. Finally, we offer a case study to validate the proposed methodology. The case study and evaluation show the advantages of the proposed security assessment mechanism.

A Security Assessment Mechanism for Software-Defined Networking-Based Mobile Networks

PubMed Central

Luo, Shibo; Dong, Mianxiong; Ota, Kaoru; Wu, Jun; Li, Jianhua

2015-01-01

Software-Defined Networking-based Mobile Networks (SDN-MNs) are considered the future of 5G mobile network architecture. With the evolving cyber-attack threat, security assessments need to be performed in the network management. Due to the distinctive features of SDN-MNs, such as their dynamic nature and complexity, traditional network security assessment methodologies cannot be applied directly to SDN-MNs, and a novel security assessment methodology is needed. In this paper, an effective security assessment mechanism based on attack graphs and an Analytic Hierarchy Process (AHP) is proposed for SDN-MNs. Firstly, this paper discusses the security assessment problem of SDN-MNs and proposes a methodology using attack graphs and AHP. Secondly, to address the diversity and complexity of SDN-MNs, a novel attack graph definition and attack graph generation algorithm are proposed. In order to quantify security levels, the Node Minimal Effort (NME) is defined to quantify attack cost and derive system security levels based on NME. Thirdly, to calculate the NME of an attack graph that takes the dynamic factors of SDN-MN into consideration, we use AHP integrated with the Technique for Order Preference by Similarity to an Ideal Solution (TOPSIS) as the methodology. Finally, we offer a case study to validate the proposed methodology. The case study and evaluation show the advantages of the proposed security assessment mechanism. PMID:26694409

Organizational Learning and Power Dynamics: A Study in a Brazilian University

ERIC Educational Resources Information Center

Santos, Jane Lucia Silva; Steil, Andrea Valéria

2015-01-01

Purpose: This paper aims to describe and analyze organizational learning processes and power dynamics during the adoption and use of an information system (IS) at a Brazilian public organization. Design/methodology/approach: A case study was chosen as the research method. Data were gathered from documents and interviews with key informants.…

Unfolding the Knowledge and Power Dynamics of the "Farmers-Rural Extensionists" Interface in North-Eastern Argentina

ERIC Educational Resources Information Center

Landini, Fernando

2016-01-01

Purpose: In this paper, the knowledge dynamics of the farmer-rural extensionist' interface were explored from extensionists' perspective with the aim of understanding the matchmaking processes between supply and demand of extension services at the micro-level. Design/methodology/approach: Forty semi-structured interviews were conducted with…

Dynamical Geometry: Analysis of Mistakes in Student Constructions

ERIC Educational Resources Information Center

Vanicek, Jiri

2007-01-01

In the early stages of working with dynamical geometry environments, students make many more mistakes than if they thought out and implemented the same constructions on paper. Most Czech teachers have very little experience of doing geometry using computers. A methodology which could help them to teach students to avoid mistakes dependent on the…

Dynamics of Western Career Attributes in the Russian Context

ERIC Educational Resources Information Center

Khapova, Svetlana N.; Korotov, Konstantin

2007-01-01

Purpose: The purpose of this article is to raise awareness of the dynamic character of career and its key attributes, and the embeddedness of their definitions and meanings in national social, political and economic contexts. Design/methodology/approach: Features of three recent distinct social, political and economic situations in Russia are used…

Early Maternal Employment and Children's Vocabulary and Inductive Reasoning Ability: A Dynamic Approach

ERIC Educational Resources Information Center

Kühhirt, Michael; Klein, Markus

2018-01-01

This study investigates the relationship between early maternal employment history and children's vocabulary and inductive reasoning ability at age 5, drawing on longitudinal information on 2,200 children from the Growing Up in Scotland data. Prior research rarely addresses dynamics in maternal employment and the methodological ramifications of…

Modeling Spring Mass System with System Dynamics Approach in Middle School Education

ERIC Educational Resources Information Center

Nuhoglu, Hasret

2008-01-01

System Dynamics is a well formulated methodology for analyzing the components of a system including causeeffect relationships and their underlying mathematics and logic, time delays, and feedback loops. It began in the business and manufacturing world, but is now affecting education and many other disciplines. Having inspired by successful policy…

Modeling Spring Mass System with System Dynamics Approach in Middle School Education

ERIC Educational Resources Information Center

Nuhoglu, Hasret

2008-01-01

System Dynamics is a well formulated methodology for analyzing the components of a system including cause-effect relationships and their underlying mathematics and logic, time delays, and feedback loops. It began in the business and manufacturing world, but is now affecting education and many other disciplines. Having inspired by successful policy…

DYNER: A DYNamic ClustER for Education and Research

ERIC Educational Resources Information Center

Kehagias, Dimitris; Grivas, Michael; Mamalis, Basilis; Pantziou, Grammati

2006-01-01

Purpose: The purpose of this paper is to evaluate the use of a non-expensive dynamic computing resource, consisting of a Beowulf class cluster and a NoW, as an educational and research infrastructure. Design/methodology/approach: Clusters, built using commodity-off-the-shelf (COTS) hardware components and free, or commonly used, software, provide…

Understanding the Influence of Organizational Culture and Group Dynamics on Organizational Change and Learning

ERIC Educational Resources Information Center

Lucas, Colleen; Kline, Theresa

2008-01-01

Purpose: The purpose of this study is to investigate the relationship between organizational culture, group dynamics, and organizational learning in the context of organizational change. Design/methodology/approach: A case study was used to examine cultural and group level factors that potentially influence groups' learning in the context of…

Careers in Academe: The Academic Labour Market as an Eco-System

ERIC Educational Resources Information Center

Baruch, Yehuda

2013-01-01

Purpose: This paper aims to explore the contrast between stable and dynamic labour markets in academe in light of career theories that were originally developed for business environments. Design/methodology/approach: A conceptual design, offering the eco-system as a framework. Findings: It evaluates their relevance and applicability to dynamic and…

A TAPS Interactive Multimedia Package to Solve Engineering Dynamics Problem

ERIC Educational Resources Information Center

Sidhu, S. Manjit; Selvanathan, N.

2005-01-01

Purpose: To expose engineering students to using modern technologies, such as multimedia packages, to learn, visualize and solve engineering problems, such as in mechanics dynamics. Design/methodology/approach: A multimedia problem-solving prototype package is developed to help students solve an engineering problem in a step-by-step approach. A…

Direct dynamic kinetic analysis and computer simulation of growth of Clostridium perfringens in cooked turkey during cooling

USDA-ARS?s Scientific Manuscript database

This research applied a new one-step methodology to directly construct a tertiary model for describing the growth of C. perfringens in cooked turkey meat under dynamically cooling conditions. The kinetic parameters of the growth models were determined by numerical analysis and optimization using mu...

Emerging Trends in Science Education in a Dynamic Academic Environment

ERIC Educational Resources Information Center

Avwiri, H. E.

2016-01-01

Emerging Trends in Science Education in a Dynamic Academic Environment highlights the changes that have occurred in science education particularly in institutions of higher learning in southern Nigeria. Impelled by the fact that most Nigerian Universities and Colleges of Education still adhere to the practices and teaching methodologies of the…

Exploring the Dynamic Long-Term Interaction between Cognitive and Psychosocial Resources in Adult Second Language Development at Varying Proficiency

ERIC Educational Resources Information Center

Serafini, Ellen J.

2017-01-01

This study draws on conceptual and methodological insights afforded within a dynamic systems perspective to explore shifting interrelationships between cognitive capacity and motivational resources in instructed adult second language (L2) learners of Spanish at increasing proficiency. Relationships that emerged showed both stability and…

Designing Online Problem Representation Engine for Conceptual Change

ERIC Educational Resources Information Center

Lee, Chwee Beng; Ling, Keck Voon

2012-01-01

Purpose: This paper aims to describe the web-based scaffold dynamic simulation system (PRES-on) designed for pre-service teachers. Design/methodology/approach: The paper describes the initial design of a web-based scaffold dynamic simulation system (PRES-on) as a cognitive tool for learners to represent problems. For the widespread use of the…

Proposed solution methodology for the dynamically coupled nonlinear geared rotor mechanics equations

NASA Technical Reports Server (NTRS)

Mitchell, L. D.; David, J. W.

1983-01-01

The equations which describe the three-dimensional motion of an unbalanced rigid disk in a shaft system are nonlinear and contain dynamic-coupling terms. Traditionally, investigators have used an order analysis to justify ignoring the nonlinear terms in the equations of motion, producing a set of linear equations. This paper will show that, when gears are included in such a rotor system, the nonlinear dynamic-coupling terms are potentially as large as the linear terms. Because of this, one must attempt to solve the nonlinear rotor mechanics equations. A solution methodology is investigated to obtain approximate steady-state solutions to these equations. As an example of the use of the technique, a simpler set of equations is solved and the results compared to numerical simulations. These equations represent the forced, steady-state response of a spring-supported pendulum. These equations were chosen because they contain the type of nonlinear terms found in the dynamically-coupled nonlinear rotor equations. The numerical simulations indicate this method is reasonably accurate even when the nonlinearities are large.

Damping mathematical modelling and dynamic responses for FRP laminated composite plates with polymer matrix

NASA Astrophysics Data System (ADS)

Liu, Qimao

2018-02-01

This paper proposes an assumption that the fibre is elastic material and polymer matrix is viscoelastic material so that the energy dissipation depends only on the polymer matrix in dynamic response process. The damping force vectors in frequency and time domains, of FRP (Fibre-Reinforced Polymer matrix) laminated composite plates, are derived based on this assumption. The governing equations of FRP laminated composite plates are formulated in both frequency and time domains. The direct inversion method and direct time integration method for nonviscously damped systems are employed to solve the governing equations and achieve the dynamic responses in frequency and time domains, respectively. The computational procedure is given in detail. Finally, dynamic responses (frequency responses with nonzero and zero initial conditions, free vibration, forced vibrations with nonzero and zero initial conditions) of a FRP laminated composite plate are computed using the proposed methodology. The proposed methodology in this paper is easy to be inserted into the commercial finite element analysis software. The proposed assumption, based on the theory of material mechanics, needs to be further proved by experiment technique in the future.

Dynamic modeling and optimization for space logistics using time-expanded networks

NASA Astrophysics Data System (ADS)

Ho, Koki; de Weck, Olivier L.; Hoffman, Jeffrey A.; Shishko, Robert

2014-12-01

This research develops a dynamic logistics network formulation for lifecycle optimization of mission sequences as a system-level integrated method to find an optimal combination of technologies to be used at each stage of the campaign. This formulation can find the optimal transportation architecture considering its technology trades over time. The proposed methodologies are inspired by the ground logistics analysis techniques based on linear programming network optimization. Particularly, the time-expanded network and its extension are developed for dynamic space logistics network optimization trading the quality of the solution with the computational load. In this paper, the methodologies are applied to a human Mars exploration architecture design problem. The results reveal multiple dynamic system-level trades over time and give recommendation of the optimal strategy for the human Mars exploration architecture. The considered trades include those between In-Situ Resource Utilization (ISRU) and propulsion technologies as well as the orbit and depot location selections over time. This research serves as a precursor for eventual permanent settlement and colonization of other planets by humans and us becoming a multi-planet species.

A new methodology to integrate planetary quarantine requirements into mission planning, with application to a Jupiter orbiter

NASA Technical Reports Server (NTRS)

Howard, R. A.; North, D. W.; Pezier, J. P.

1975-01-01

A new methodology is proposed for integrating planetary quarantine objectives into space exploration planning. This methodology is designed to remedy the major weaknesses inherent in the current formulation of planetary quarantine requirements. Application of the methodology is illustrated by a tutorial analysis of a proposed Jupiter Orbiter mission. The proposed methodology reformulates planetary quarantine planning as a sequential decision problem. Rather than concentrating on a nominal plan, all decision alternatives and possible consequences are laid out in a decision tree. Probabilities and values are associated with the outcomes, including the outcome of contamination. The process of allocating probabilities, which could not be made perfectly unambiguous and systematic, is replaced by decomposition and optimization techniques based on principles of dynamic programming. Thus, the new methodology provides logical integration of all available information and allows selection of the best strategy consistent with quarantine and other space exploration goals.

Measurement of 3-D Vibrational Motion by Dynamic Photogrammetry Using Least-Square Image Matching for Sub-Pixel Targeting to Improve Accuracy.

PubMed

Lee, Hyoseong; Rhee, Huinam; Oh, Jae Hong; Park, Jin Ho

2016-03-11

This paper deals with an improved methodology to measure three-dimensional dynamic displacements of a structure by digital close-range photogrammetry. A series of stereo images of a vibrating structure installed with targets are taken at specified intervals by using two daily-use cameras. A new methodology is proposed to accurately trace the spatial displacement of each target in three-dimensional space. This method combines the correlation and the least-square image matching so that the sub-pixel targeting can be obtained to increase the measurement accuracy. Collinearity and space resection theory are used to determine the interior and exterior orientation parameters. To verify the proposed method, experiments have been performed to measure displacements of a cantilevered beam excited by an electrodynamic shaker, which is vibrating in a complex configuration with mixed bending and torsional motions simultaneously with multiple frequencies. The results by the present method showed good agreement with the measurement by two laser displacement sensors. The proposed methodology only requires inexpensive daily-use cameras, and can remotely detect the dynamic displacement of a structure vibrating in a complex three-dimensional defection shape up to sub-pixel accuracy. It has abundant potential applications to various fields, e.g., remote vibration monitoring of an inaccessible or dangerous facility.

Measurement of 3-D Vibrational Motion by Dynamic Photogrammetry Using Least-Square Image Matching for Sub-Pixel Targeting to Improve Accuracy

PubMed Central

Lee, Hyoseong; Rhee, Huinam; Oh, Jae Hong; Park, Jin Ho

2016-01-01

This paper deals with an improved methodology to measure three-dimensional dynamic displacements of a structure by digital close-range photogrammetry. A series of stereo images of a vibrating structure installed with targets are taken at specified intervals by using two daily-use cameras. A new methodology is proposed to accurately trace the spatial displacement of each target in three-dimensional space. This method combines the correlation and the least-square image matching so that the sub-pixel targeting can be obtained to increase the measurement accuracy. Collinearity and space resection theory are used to determine the interior and exterior orientation parameters. To verify the proposed method, experiments have been performed to measure displacements of a cantilevered beam excited by an electrodynamic shaker, which is vibrating in a complex configuration with mixed bending and torsional motions simultaneously with multiple frequencies. The results by the present method showed good agreement with the measurement by two laser displacement sensors. The proposed methodology only requires inexpensive daily-use cameras, and can remotely detect the dynamic displacement of a structure vibrating in a complex three-dimensional defection shape up to sub-pixel accuracy. It has abundant potential applications to various fields, e.g., remote vibration monitoring of an inaccessible or dangerous facility. PMID:26978366

A proposed methodology for studying the historical trajectory of words' meaning through Tsallis entropy

NASA Astrophysics Data System (ADS)

Neuman, Yair; Cohen, Yochai; Israeli, Navot; Tamir, Boaz

2018-02-01

The availability of historical textual corpora has led to the study of words' frequency along the historical time line, as representing the public's focus of attention over time. However, studying of the dynamics of words' meaning is still in its infancy. In this paper, we propose a methodology for studying the historical trajectory of words' meaning through Tsallis entropy. First, we present the idea that the meaning of a word may be studied through the entropy of its embedding. Using two historical case studies, we show that this entropy measure is correlated with the intensity in which a word is used. More importantly, we show that using Tsallis entropy with a superadditive entropy index may provide a better estimation of a word's frequency of use than using Shannon entropy. We explain this finding as resulting from an increasing redundancy between the words that comprise the semantic field of the target word and develop a new measure of redundancy between words. Using this measure, which relies on the Tsallis version of the Kullback-Leibler divergence, we show that the evolving meaning of a word involves the dynamics of increasing redundancy between components of its semantic field. The proposed methodology may enrich the toolkit of researchers who study the dynamics of word senses.

An Effective Modal Approach to the Dynamic Evaluation of Fracture Toughness of Quasi-Brittle Materials

NASA Astrophysics Data System (ADS)

Ferreira, L. E. T.; Vareda, L. V.; Hanai, J. B.; Sousa, J. L. A. O.; Silva, A. I.

2017-05-01

A modal dynamic analysis is used as the tool to evaluate the fracture toughness of concrete from the results of notched-through beam tests. The dimensionless functions describing the relation between the frequencies and specimen geometry used for identifying the variation in the natural frequency as a function of crack depth is first determined for a 150 × 150 × 500-mm notched-through specimen. The frequency decrease resulting from the propagating crack is modeled through a modal/fracture mechanics approach, leading to determination of an effective crack length. This length, obtained numerically, is used to evaluate the fracture toughness of concrete, the critical crack mouth opening displacements, and the brittleness index proposed. The methodology is applied to tests performed on high-strength concrete specimens. The frequency response for each specimen is evaluated before and after each crack propagation step. The methodology is then validated by comparison with results from the application of other methodologies described in the literature and suggested by RILEM.

Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation. Volume 2, Part 2: Appendixes B, C, D and E

NASA Technical Reports Server (NTRS)

Lowrie, J. W.; Fermelia, A. J.; Haley, D. C.; Gremban, K. D.; Vanbaalen, J.; Walsh, R. W.

1982-01-01

The derivation of the equations is presented, the rate control algorithm described, and simulation methodologies summarized. A set of dynamics equations that can be used recursively to calculate forces and torques acting at the joints of an n link manipulator given the manipulator joint rates are derived. The equations are valid for any n link manipulator system with any kind of joints connected in any sequence. The equations of motion for the class of manipulators consisting of n rigid links interconnected by rotary joints are derived. A technique is outlined for reducing the system of equations to eliminate contraint torques. The linearized dynamics equations for an n link manipulator system are derived. The general n link linearized equations are then applied to a two link configuration. The coordinated rate control algorithm used to compute individual joint rates when given end effector rates is described. A short discussion of simulation methodologies is presented.

Review of evaluation on ecological carrying capacity: The progress and trend of methodology

NASA Astrophysics Data System (ADS)

Wang, S. F.; Xu, Y.; Liu, T. J.; Ye, J. M.; Pan, B. L.; Chu, C.; Peng, Z. L.

2018-02-01

The ecological carrying capacity (ECC) has been regarded as an important reference to indicate the level of regional sustainable development since the very beginning of twenty-first century. By a brief review of the main progress in ECC evaluation methodologies in recent five years, this paper systematically discusses the features and differences of these methods and expounds the current states and future development trend of ECC methodology. The result shows that further exploration in terms of the dynamic, comprehensive and intelligent assessment technologies needs to be provided in order to form a unified and scientific ECC methodology system and to produce a reliable basis for environmental-economic decision-makings.

Design Of Combined Stochastic Feedforward/Feedback Control

NASA Technical Reports Server (NTRS)

Halyo, Nesim

1989-01-01

Methodology accommodates variety of control structures and design techniques. In methodology for combined stochastic feedforward/feedback control, main objectives of feedforward and feedback control laws seen clearly. Inclusion of error-integral feedback, dynamic compensation, rate-command control structure, and like integral element of methodology. Another advantage of methodology flexibility to develop variety of techniques for design of feedback control with arbitrary structures to obtain feedback controller: includes stochastic output feedback, multiconfiguration control, decentralized control, or frequency and classical control methods. Control modes of system include capture and tracking of localizer and glideslope, crab, decrab, and flare. By use of recommended incremental implementation, control laws simulated on digital computer and connected with nonlinear digital simulation of aircraft and its systems.

Development of Constraint Force Equation Methodology for Application to Multi-Body Dynamics Including Launch Vehicle Stage Seperation

NASA Technical Reports Server (NTRS)

Pamadi, Bandu N.; Toniolo, Matthew D.; Tartabini, Paul V.; Roithmayr, Carlos M.; Albertson, Cindy W.; Karlgaard, Christopher D.

2016-01-01

The objective of this report is to develop and implement a physics based method for analysis and simulation of multi-body dynamics including launch vehicle stage separation. The constraint force equation (CFE) methodology discussed in this report provides such a framework for modeling constraint forces and moments acting at joints when the vehicles are still connected. Several stand-alone test cases involving various types of joints were developed to validate the CFE methodology. The results were compared with ADAMS(Registered Trademark) and Autolev, two different industry standard benchmark codes for multi-body dynamic analysis and simulations. However, these two codes are not designed for aerospace flight trajectory simulations. After this validation exercise, the CFE algorithm was implemented in Program to Optimize Simulated Trajectories II (POST2) to provide a capability to simulate end-to-end trajectories of launch vehicles including stage separation. The POST2/CFE methodology was applied to the STS-1 Space Shuttle solid rocket booster (SRB) separation and Hyper-X Research Vehicle (HXRV) separation from the Pegasus booster as a further test and validation for its application to launch vehicle stage separation problems. Finally, to demonstrate end-to-end simulation capability, POST2/CFE was applied to the ascent, orbit insertion, and booster return of a reusable two-stage-to-orbit (TSTO) vehicle concept. With these validation exercises, POST2/CFE software can be used for performing conceptual level end-to-end simulations, including launch vehicle stage separation, for problems similar to those discussed in this report.

Pressure Distribution and Performance Impacts of Aerospike Nozzles on Rotating Detonation Engines

DTIC Science & Technology

2017-06-01

design methodology at both on- and off-design conditions anticipated throughout the combustion cycle. Steady-state, non -reacting computational fluid...operation. Therefore, the nozzle contour was designed using a traditional, steady-state design methodology at both on- and off-design conditions...anticipated throughout the combustion cycle. Steady-state, non -reacting computational fluid dynamics (CFD) simulations were performed on various nozzle

Investigating Dynamics of Eccentricity in Turbomachines

NASA Technical Reports Server (NTRS)

Baun, Daniel

2010-01-01

A methodology (and hardware and software to implement the methodology) has been developed as a means of investigating coupling between certain rotordynamic and hydrodynamic phenomena in turbomachines. Originally, the methodology was intended for application in an investigation of coupled rotordynamic and hydrodynamic effects postulated to have caused high synchronous vibration in the space shuttle s high-pressure oxygen turbopump (HPOTP). The methodology can also be applied in investigating (for the purpose of developing means of suppressing) undesired hydrodynamic rotor/stator interactions in turbomachines in general. The methodology and the types of phenomena that can be investigated by use of the methodology are best summarized by citing the original application as an example. In that application, in consideration of the high synchronous vibration in the space-shuttle main engine (SSME) HPOTP, it was determined to be necessary to perform tests to investigate the influence of inducer eccentricity and/or synchronous whirl motion on inducer hydrodynamic forces under prescribed flow and cavitation conditions. It was believed that manufacturing tolerances of the turbopump resulted in some induced runout of the pump rotor. Such runout, if oriented with an inducer blade, would cause that blade to run with tip clearance smaller than the tip clearances of the other inducer blades. It was hypothesized that the resulting hydraulic asymmetry, coupled with alternating blade cavitation, could give rise to the observed high synchronous vibration. In tests performed to investigate this hypothesis, prescribed rotor whirl motions have been imposed on a 1/3-scale water-rig version of the SSME LPOTP inducer (which is also a 4-biased inducer having similar cavitation dynamics as the HPOTP) in a magnetic-bearing test facility. The particular magnetic-bearing test facility, through active vibration control, affords a capability to impose, on the rotor, whirl orbits having shapes and whirl rates prescribed by the user, and to simultaneously measure the resulting hydrodynamic forces generated by the impeller. Active control also made it possible to modulate the inducer-blade running tip clearance and consequently effect alternating blade cavitation. The measured hydraulic forces have been compared and correlated with shroud dynamic-pressure measurements.

Tenth Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion, part 2

NASA Technical Reports Server (NTRS)

Williams, R. W. (Compiler)

1992-01-01

Presented here are 59 abstracts and presentations and three invited presentations given at the Tenth Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion held at the George C. Marshall Space Flight Center, April 28-30, 1992. The purpose of the workshop is to discuss experimental and computational fluid dynamic activities in rocket propulsion. The workshop is an open meeting for government, industry, and academia. A broad number of topics are discussed, including a computational fluid dynamic methodology, liquid and solid rocket propulsion, turbomachinery, combustion, heat transfer, and grid generation.

Eleventh Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion

NASA Technical Reports Server (NTRS)

Williams, R. W. (Compiler)

1993-01-01

Conference publication includes 79 abstracts and presentations and 3 invited presentations given at the Eleventh Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion held at George C. Marshall Space Flight Center, April 20-22, 1993. The purpose of the workshop is to discuss experimental and computational fluid dynamic activities in rocket propulsion. The workshop is an open meeting for government, industry, and academia. A broad number of topics are discussed including computational fluid dynamic methodology, liquid and solid rocket propulsion, turbomachinery, combustion, heat transfer, and grid generation.

Eleventh Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion, Part 1

NASA Technical Reports Server (NTRS)

Williams, Robert W. (Compiler)

1993-01-01

Conference publication includes 79 abstracts and presentations given at the Eleventh Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion held at the George C. Marshall Space Flight Center, April 20-22, 1993. The purpose of this workshop is to discuss experimental and computational fluid dynamic activities in rocket propulsion. The workshop is an open meeting for government, industry, and academia. A broad number of topics are discussed including computational fluid dynamic methodology, liquid and solid rocket propulsion, turbomachinery, combustion, heat transfer, and grid generation.

Development of methodology for horizontal axis wind turbine dynamic analysis

NASA Technical Reports Server (NTRS)

Dugundji, J.

1982-01-01

Horizontal axis wind turbine dynamics were studied. The following findings are summarized: (1) review of the MOSTAS computer programs for dynamic analysis of horizontal axis wind turbines; (2) review of various analysis methods for rotating systems with periodic coefficients; (3) review of structural dynamics analysis tools for large wind turbine; (4) experiments for yaw characteristics of a rotating rotor; (5) development of a finite element model for rotors; (6) development of simple models for aeroelastics; and (7) development of simple models for stability and response of wind turbines on flexible towers.

Integrating protein structural dynamics and evolutionary analysis with Bio3D.

PubMed

Skjærven, Lars; Yao, Xin-Qiu; Scarabelli, Guido; Grant, Barry J

2014-12-10

Popular bioinformatics approaches for studying protein functional dynamics include comparisons of crystallographic structures, molecular dynamics simulations and normal mode analysis. However, determining how observed displacements and predicted motions from these traditionally separate analyses relate to each other, as well as to the evolution of sequence, structure and function within large protein families, remains a considerable challenge. This is in part due to the general lack of tools that integrate information of molecular structure, dynamics and evolution. Here, we describe the integration of new methodologies for evolutionary sequence, structure and simulation analysis into the Bio3D package. This major update includes unique high-throughput normal mode analysis for examining and contrasting the dynamics of related proteins with non-identical sequences and structures, as well as new methods for quantifying dynamical couplings and their residue-wise dissection from correlation network analysis. These new methodologies are integrated with major biomolecular databases as well as established methods for evolutionary sequence and comparative structural analysis. New functionality for directly comparing results derived from normal modes, molecular dynamics and principal component analysis of heterogeneous experimental structure distributions is also included. We demonstrate these integrated capabilities with example applications to dihydrofolate reductase and heterotrimeric G-protein families along with a discussion of the mechanistic insight provided in each case. The integration of structural dynamics and evolutionary analysis in Bio3D enables researchers to go beyond a prediction of single protein dynamics to investigate dynamical features across large protein families. The Bio3D package is distributed with full source code and extensive documentation as a platform independent R package under a GPL2 license from http://thegrantlab.org/bio3d/ .

Using the Spatial Distribution of Installers to Define Solar Photovoltaic Markets

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Shaughnessy, Eric; Nemet, Gregory F.; Darghouth, Naim

2016-09-01

Solar PV market research to date has largely relied on arbitrary jurisdictional boundaries, such as counties, to study solar PV market dynamics. This paper seeks to improve solar PV market research by developing a methodology to define solar PV markets. The methodology is based on the spatial distribution of solar PV installers. An algorithm is developed and applied to a rich dataset of solar PV installations to study the outcomes of the installer-based market definitions. The installer-based approach exhibits several desirable properties. Specifically, the higher market granularity of the installer-based approach will allow future PV market research to study themore » relationship between market dynamics and pricing with more precision.« less

A Dynamic Approach to Make CDS/ISIS Databases Interoperable over the Internet Using the OAI Protocol

ERIC Educational Resources Information Center

Jayakanth, F.; Maly, K.; Zubair, M.; Aswath, L.

2006-01-01

Purpose: A dynamic approach to making legacy databases, like CDS/ISIS, interoperable with OAI-compliant digital libraries (DLs). Design/methodology/approach: There are many bibliographic databases that are being maintained using legacy database systems. CDS/ISIS is one such legacy database system. It was designed and developed specifically for…

Multi-Stakeholder Process Strengthens Agricultural Innovations and Sustainable Livelihoods of Farmers in Southern Nigeria

ERIC Educational Resources Information Center

Bisseleua, D. H. B.; Idrissou, L.; Olurotimi, P.; Ogunniyi, A.; Mignouna, D.; Bamire, S. A.

2018-01-01

Purpose: In this paper, we explore the strategic role of Multi-stakeholder processes (MSP) in agricultural innovations and how it has impacted livelihood assets' (LAs) capital dynamics of stakeholders in platforms in West Africa. Design/Methodology/Approach: We demonstrate how LA capitals and socio-economic dynamics induced by MSP can enhance…

Shape selection in Landsat time series: A tool for monitoring forest dynamics

Treesearch

Gretchen G. Moisen; Mary C. Meyer; Todd A. Schroeder; Xiyue Liao; Karen G. Schleeweis; Elizabeth A. Freeman; Chris Toney

2016-01-01

We present a new methodology for fitting nonparametric shape-restricted regression splines to time series of Landsat imagery for the purpose of modeling, mapping, and monitoring annual forest disturbance dynamics over nearly three decades. For each pixel and spectral band or index of choice in temporal Landsat data, our method delivers a smoothed rendition of...

Critical Moments in the Process of Educational Change: Understanding the Dynamics of Change among Teacher Educators

ERIC Educational Resources Information Center

Brody, David L.; Hadar, Linor Lea

2018-01-01

This study examines the complex process of change among teacher educators who have chosen to improve their practice in a professional development community. Storyline methodology was used to reveal the dynamic process which teacher educators undergo when they consider adopting innovative pedagogy. Findings reveal critical moments in professional…

Likelihood Methods for Adaptive Filtering and Smoothing. Technical Report #455.

ERIC Educational Resources Information Center

Butler, Ronald W.

The dynamic linear model or Kalman filtering model provides a useful methodology for predicting the past, present, and future states of a dynamic system, such as an object in motion or an economic or social indicator that is changing systematically with time. Recursive likelihood methods for adaptive Kalman filtering and smoothing are developed.…

The Influences of Static and Interactive Dynamic Facial Stimuli on Visual Strategies in Persons with Asperger Syndrome

ERIC Educational Resources Information Center

Falkmer, Marita; Bjallmark, Anna; Larsson, Matilda; Falkmer, Torbjorn

2011-01-01

Several studies, using eye tracking methodology, suggest that different visual strategies in persons with autism spectrum conditions, compared with controls, are applied when viewing facial stimuli. Most eye tracking studies are, however, made in laboratory settings with either static (photos) or non-interactive dynamic stimuli, such as video…

Dragging Maintaining Symmetry: Can It Generate the Concept of Inclusivity as well as a Family of Shapes?

ERIC Educational Resources Information Center

Forsythe, Susan K.

2015-01-01

This article describes a project using Design Based Research methodology to ascertain whether a pedagogical task based on a dynamic figure designed in a Dynamic Geometry Software (DGS) program could be instrumental in developing students' geometrical reasoning. A dragging strategy which I have named "Dragging Maintaining Symmetry" (DMS)…

An Unscented Kalman Filter Approach to the Estimation of Nonlinear Dynamical Systems Models

ERIC Educational Resources Information Center

Chow, Sy-Miin; Ferrer, Emilio; Nesselroade, John R.

2007-01-01

In the past several decades, methodologies used to estimate nonlinear relationships among latent variables have been developed almost exclusively to fit cross-sectional models. We present a relatively new estimation approach, the unscented Kalman filter (UKF), and illustrate its potential as a tool for fitting nonlinear dynamic models in two ways:…

Using Sociocultural Perspectives: The Dynamic Process of Designing and Implementing Class Activities in an Online Japanese Language Course

ERIC Educational Resources Information Center

Shibakawa, Mayumi

2012-01-01

The study documented the dynamic process of designing and implementing instructional interventions in an online course of Japanese language and culture at a two-year college. The results have impact in three distinct areas: pedagogical, theoretical, and methodological. First, the interventions that encouraged student agency with rich…

Bifurcation and Hysteresis Effects in Student Performance: The Signature of Complexity and Chaos in Educational Research

ERIC Educational Resources Information Center

Stamovlasis, Dimitrios

2014-01-01

This paper addresses some methodological issues concerning traditional linear approaches and shows the need for a paradigm shift in education research towards the Complexity and Nonlinear Dynamical Systems (NDS) framework. It presents a quantitative piece of research aiming to test the nonlinear dynamical hypothesis in education. It applies…

A review on bridge dynamic displacement monitoring using global positioning system and accelerometer

NASA Astrophysics Data System (ADS)

Yunus, Mohd Zulkifli Mohd; Ibrahim, Nuremira; Ahmad, Fatimah Shafinaz

2018-02-01

This paper reviews previous research on bridge dynamic displacement monitoring using Global Positioning System (GPS) and an accelerometer for Structural Health Monitoring (SHM) of bridge. These include the review of the advantages and disadvantages of the measurement as well as the methodology of the measurements used in the recent research study. This review could provide a preliminary decision overview for students or researchers before initiating a research related to the bridge dynamic displacement monitoring.

Application of Tube Dynamics to Non-Statistical Reaction Processes

NASA Astrophysics Data System (ADS)

Gabern, F.; Koon, W. S.; Marsden, J. E.; Ross, S. D.; Yanao, T.

2006-06-01

A technique based on dynamical systems theory is introduced for the computation of lifetime distributions and rates of chemical reactions and scattering phenomena, even in systems that exhibit non-statistical behavior. In particular, we merge invariant manifold tube dynamics with Monte Carlo volume determination for accurate rate calculations. This methodology is applied to a three-degree-of-freedom model problem and some ideas on how it might be extended to higher-degree-of-freedom systems are presented.

Identification of drivers of (dis)liking based on dynamic sensory profiles: Comparison of Temporal Dominance of Sensations and Temporal Check-all-that-apply.

PubMed

Ares, Gastón; Alcaire, Florencia; Antúnez, Lucía; Vidal, Leticia; Giménez, Ana; Castura, John C

2017-02-01

Temporal Dominance of Sensations (TDS) and Temporal Check-all-that-apply (TCATA) are two multi-attribute methods for dynamic sensory characterization. Previous research has shown that both methodologies provide complementary information. However, it remains an open question which of the two approaches better explains consumers' hedonic perception of products. In this context, the aim of the present work was to compare TDS and TCATA in terms of their ability to identify the influence of the dynamic sensory profile of food products on consumer overall liking scores. Two consumer studies were conducted using two different product categories (French bread and vanilla milk desserts). In each study, a between-subjects design was used to obtain dynamic sensory profiles using TDS and TCATA. After the dynamic sensory characterization tasks consumers rated their liking using a 9-point hedonic scale. Across the two studies, both methodologies provided similar information on the main drivers of liking and disliking, particularly when samples showed clear differences in liking. However, in one of the studies attribute applicability from TCATA provided additional insights on the influence of the dynamics of the sensory characteristics of products on consumers' liking. Results of the present work stress the complementarity between TCATA and TDS and highlight the potentiality of TCATA to provide a more detailed description of the dynamics of sensory perception during consumption. Copyright © 2016 Elsevier Ltd. All rights reserved.

The relationship between structure and function in locally observed complex networks

NASA Astrophysics Data System (ADS)

Comin, Cesar H.; Viana, Matheus P.; Costa, Luciano da F.

2013-01-01

Recently, studies looking at the small scale interactions taking place in complex networks have started to unveil the wealth of interactions that occur between groups of nodes. Such findings make the claim for a new systematic methodology to quantify, at node level, how dynamics are influenced (or differentiated) by the structure of the underlying system. Here we define a new measure that, based on the dynamical characteristics obtained for a large set of initial conditions, compares the dynamical behavior of the nodes present in the system. Through this measure, we find that the geographic and Barabási-Albert models have a high capacity for generating networks that exhibit groups of nodes with distinct dynamics compared to the rest of the network. The application of our methodology is illustrated with respect to two real systems. In the first we use the neuronal network of the nematode Caenorhabditis elegans to show that the interneurons of the ventral cord of the nematode present a very large dynamical differentiation when compared to the rest of the network. The second application concerns the SIS epidemic model on an airport network, where we quantify how different the distribution of infection times of high and low degree nodes can be, when compared to the expected value for the network.

In silico strategies toward enzyme function and dynamics.

PubMed

Estácio, Sílvia G

2012-01-01

Enzymes are outstanding biocatalysts involved in a plethora of chemical reactions occurring in the cell. Despite their incommensurable importance, a comprehensive understanding of enzyme catalysis is still missing. This task becomes more laborious given the unavoidability of including the inherent dynamic nature of enzymes into that description. As such, it is essential to ascertain the nature and contribution of enzyme conformational changes to catalysis and to evaluate the adequacy of the proposal associating protein internal motions to the rate enhancement achieved. Dynamic events in enzymes span a wide range of time- and length-scales which have led to a surge in multiscale methodologies targeting enzyme function and dynamics. Computational strategies assume a preponderant role in such studies by allowing the atomic detail investigation of the fundamental mechanisms of enzyme catalysis thus surpassing what is achievable through experiments. While high-accuracy quantum mechanical methods are indicated to uncover the details of the chemical reaction occurring at the active site, molecular mechanical force fields and molecular dynamics approaches provide powerful means to access the conformational energy landscape accessible to enzymes. This review outlines some of the most important in silico methodologies in this area, highlighting examples of problems tackled and the insights obtained. Copyright © 2012 Elsevier Inc. All rights reserved.

Dynamic modelling of n-of-1 data: powerful and flexible data analytics applied to individualised studies.

PubMed

Vieira, Rute; McDonald, Suzanne; Araújo-Soares, Vera; Sniehotta, Falko F; Henderson, Robin

2017-09-01

N-of-1 studies are based on repeated observations within an individual or unit over time and are acknowledged as an important research method for generating scientific evidence about the health or behaviour of an individual. Statistical analyses of n-of-1 data require accurate modelling of the outcome while accounting for its distribution, time-related trend and error structures (e.g., autocorrelation) as well as reporting readily usable contextualised effect sizes for decision-making. A number of statistical approaches have been documented but no consensus exists on which method is most appropriate for which type of n-of-1 design. We discuss the statistical considerations for analysing n-of-1 studies and briefly review some currently used methodologies. We describe dynamic regression modelling as a flexible and powerful approach, adaptable to different types of outcomes and capable of dealing with the different challenges inherent to n-of-1 statistical modelling. Dynamic modelling borrows ideas from longitudinal and event history methodologies which explicitly incorporate the role of time and the influence of past on future. We also present an illustrative example of the use of dynamic regression on monitoring physical activity during the retirement transition. Dynamic modelling has the potential to expand researchers' access to robust and user-friendly statistical methods for individualised studies.

Methodology for the Incorporation of Passive Component Aging Modeling into the RAVEN/ RELAP-7 Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mandelli, Diego; Rabiti, Cristian; Cogliati, Joshua

2014-11-01

Passive system, structure and components (SSCs) will degrade over their operation life and this degradation may cause to reduction in the safety margins of a nuclear power plant. In traditional probabilistic risk assessment (PRA) using the event-tree/fault-tree methodology, passive SSC failure rates are generally based on generic plant failure data and the true state of a specific plant is not reflected realistically. To address aging effects of passive SSCs in the traditional PRA methodology [1] does consider physics based models that account for the operating conditions in the plant, however, [1] does not include effects of surveillance/inspection. This paper representsmore » an overall methodology for the incorporation of aging modeling of passive components into the RAVEN/RELAP-7 environment which provides a framework for performing dynamic PRA. Dynamic PRA allows consideration of both epistemic and aleatory uncertainties (including those associated with maintenance activities) in a consistent phenomenological and probabilistic framework and is often needed when there is complex process/hardware/software/firmware/ human interaction [2]. Dynamic PRA has gained attention recently due to difficulties in the traditional PRA modeling of aging effects of passive components using physics based models and also in the modeling of digital instrumentation and control systems. RAVEN (Reactor Analysis and Virtual control Environment) [3] is a software package under development at the Idaho National Laboratory (INL) as an online control logic driver and post-processing tool. It is coupled to the plant transient code RELAP-7 (Reactor Excursion and Leak Analysis Program) also currently under development at INL [3], as well as RELAP 5 [4]. The overall methodology aims to: • Address multiple aging mechanisms involving large number of components in a computational feasible manner where sequencing of events is conditioned on the physical conditions predicted in a simulation environment such as RELAP-7. • Identify the risk-significant passive components, their failure modes and anticipated rates of degradation • Incorporate surveillance and maintenance activities and their effects into the plant state and into component aging progress. • Asses aging affects in a dynamic simulation environment 1. C. L. SMITH, V. N. SHAH, T. KAO, G. APOSTOLAKIS, “Incorporating Ageing Effects into Probabilistic Risk Assessment –A Feasibility Study Utilizing Reliability Physics Models,” NUREG/CR-5632, USNRC, (2001). 2. T. ALDEMIR, “A Survey of Dynamic Methodologies for Probabilistic Safety Assessment of Nuclear Power Plants, Annals of Nuclear Energy, 52, 113-124, (2013). 3. C. RABITI, A. ALFONSI, J. COGLIATI, D. MANDELLI and R. KINOSHITA “Reactor Analysis and Virtual Control Environment (RAVEN) FY12 Report,” INL/EXT-12-27351, (2012). 4. D. ANDERS et.al, "RELAP-7 Level 2 Milestone Report: Demonstration of a Steady State Single Phase PWR Simulation with RELAP-7," INL/EXT-12-25924, (2012).« less

Risk Metrics for Android (trademark) Devices

DTIC Science & Technology

2017-02-01

allows for easy distribution of malware. This report surveys malware distribution methodologies , then describes current work being done to determine the...given a standard weight of wi = 1. Two data sets were used for testing this methodology . Because the authors are Chinese, they chose to download apps...Order Analysis excels at handling non -obfuscated apps, but may not be able to detect malware that employs encryption or dynamically changes its payload

The Development of Methodologies for Determining Non-Linear Effects in Infrasound Sensors

DTIC Science & Technology

2010-09-01

THE DEVELOPMENT OF METHODOLOGIES FOR DETERMINING NON-LINEAR EFFECTS IN INFRASOUND SENSORS Darren M. Hart, Harold V. Parks, and Randy K. Rembold...the past year, four new infrasound sensor designs were evaluated for common performance characteristics, i.e., power consumption, response (amplitude...and phase), noise, full-scale, and dynamic range. In the process of evaluating a fifth infrasound sensor, which is an update of an original design

Maximum Entropy/Optimal Projection (MEOP) control design synthesis: Optimal quantification of the major design tradeoffs

NASA Technical Reports Server (NTRS)

Hyland, D. C.; Bernstein, D. S.

1987-01-01

The underlying philosophy and motivation of the optimal projection/maximum entropy (OP/ME) stochastic modeling and reduced control design methodology for high order systems with parameter uncertainties are discussed. The OP/ME design equations for reduced-order dynamic compensation including the effect of parameter uncertainties are reviewed. The application of the methodology to several Large Space Structures (LSS) problems of representative complexity is illustrated.

A new method for qualitative simulation of water resources systems: 1. Theory

NASA Astrophysics Data System (ADS)

Camara, A. S.; Pinheiro, M.; Antunes, M. P.; Seixas, M. J.

1987-11-01

A new dynamic modeling methodology, SLIN (Simulação Linguistica), allowing for the analysis of systems defined by linguistic variables, is presented. SLIN applies a set of logical rules avoiding fuzzy theoretic concepts. To make the transition from qualitative to quantitative modes, logical rules are used as well. Extensions of the methodology to simulation-optimization applications and multiexpert system modeling are also discussed.

Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design.

PubMed

Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

2015-02-28

The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

System learning approach to assess sustainability and ...

EPA Pesticide Factsheets

This paper presents a methodology that combines the power of an Artificial Neural Network and Information Theory to forecast variables describing the condition of a regional system. The novelty and strength of this approach is in the application of Fisher information, a key method in Information Theory, to preserve trends in the historical data and prevent over fitting projections. The methodology was applied to demographic, environmental, food and energy consumption, and agricultural production in the San Luis Basin regional system in Colorado, U.S.A. These variables are important for tracking conditions in human and natural systems. However, available data are often so far out of date that they limit the ability to manage these systems. Results indicate that the approaches developed provide viable tools for forecasting outcomes with the aim of assisting management toward sustainable trends. This methodology is also applicable for modeling different scenarios in other dynamic systems. Indicators are indispensable for tracking conditions in human and natural systems, however, available data is sometimes far out of date and limit the ability to gauge system status. Techniques like regression and simulation are not sufficient because system characteristics have to be modeled ensuring over simplification of complex dynamics. This work presents a methodology combining the power of an Artificial Neural Network and Information Theory to capture patterns in a real dyna

Modeling Common-Sense Decisions

NASA Astrophysics Data System (ADS)

Zak, Michail

This paper presents a methodology for efficient synthesis of dynamical model simulating a common-sense decision making process. The approach is based upon the extension of the physics' First Principles that includes behavior of living systems. The new architecture consists of motor dynamics simulating actual behavior of the object, and mental dynamics representing evolution of the corresponding knowledge-base and incorporating it in the form of information flows into the motor dynamics. The autonomy of the decision making process is achieved by a feedback from mental to motor dynamics. This feedback replaces unavailable external information by an internal knowledgebase stored in the mental model in the form of probability distributions.

Spatial operator algebra framework for multibody system dynamics

NASA Technical Reports Server (NTRS)

Rodriguez, G.; Jain, Abhinandan; Kreutz, K.

1989-01-01

The Spatial Operator Algebra framework for the dynamics of general multibody systems is described. The use of a spatial operator-based methodology permits the formulation of the dynamical equations of motion of multibody systems in a concise and systematic way. The dynamical equations of progressively more complex grid multibody systems are developed in an evolutionary manner beginning with a serial chain system, followed by a tree topology system and finally, systems with arbitrary closed loops. Operator factorizations and identities are used to develop novel recursive algorithms for the forward dynamics of systems with closed loops. Extensions required to deal with flexible elements are also discussed.

Spatial Operator Algebra for multibody system dynamics

NASA Technical Reports Server (NTRS)

Rodriguez, G.; Jain, A.; Kreutz-Delgado, K.

1992-01-01

The Spatial Operator Algebra framework for the dynamics of general multibody systems is described. The use of a spatial operator-based methodology permits the formulation of the dynamical equations of motion of multibody systems in a concise and systematic way. The dynamical equations of progressively more complex grid multibody systems are developed in an evolutionary manner beginning with a serial chain system, followed by a tree topology system and finally, systems with arbitrary closed loops. Operator factorizations and identities are used to develop novel recursive algorithms for the forward dynamics of systems with closed loops. Extensions required to deal with flexible elements are also discussed.

[Development of New Mathematical Methodology in Air Traffic Control for the Analysis of Hybrid Systems

NASA Technical Reports Server (NTRS)

Hermann, Robert

1997-01-01

The aim of this research is to develop new mathematical methodology for the analysis of hybrid systems of the type involved in Air Traffic Control (ATC) problems. Two directions of investigation were initiated. The first used the methodology of nonlinear generalized functions, whose mathematical foundations were initiated by Colombeau and developed further by Oberguggenberger; it has been extended to apply to ordinary differential. Systems of the type encountered in control in joint work with the PI and M. Oberguggenberger. This involved a 'mixture' of 'continuous' and 'discrete' methodology. ATC clearly involves mixtures of two sorts of mathematical problems: (1) The 'continuous' dynamics of a standard control type described by ordinary differential equations (ODE) of the form: {dx/dt = f(x, u)} and (2) the discrete lattice dynamics involved of cellular automata. Most of the CA literature involves a discretization of a partial differential equation system of the type encountered in physics problems (e.g. fluid and gas problems). Both of these directions requires much thinking and new development of mathematical fundamentals before they may be utilized in the ATC work. Rather than consider CA as 'discretization' of PDE systems, I believe that the ATC applications will require a completely different and new mathematical methodology, a sort of discrete analogue of jet bundles and/or the sheaf-theoretic techniques to topologists. Here too, I have begun work on virtually 'virgin' mathematical ground (at least from an 'applied' point of view) which will require considerable preliminary work.

Gas dynamic design of the pipe line compressor with 90% efficiency. Model test approval

NASA Astrophysics Data System (ADS)

Galerkin, Y.; Rekstin, A.; Soldatova, K.

2015-08-01

Gas dynamic design of the pipe line compressor 32 MW was made for PAO SMPO (Sumy, Ukraine). The technical specification requires compressor efficiency of 90%. The customer offered favorable scheme - single-stage design with console impeller and axial inlet. The authors used the standard optimization methodology of 2D impellers. The original methodology of internal scroll profiling was used to minimize efficiency losses. Radically improved 5th version of the Universal modeling method computer programs was used for precise calculation of expected performances. The customer fulfilled model tests in a 1:2 scale. Tests confirmed the calculated parameters at the design point (maximum efficiency of 90%) and in the whole range of flow rates. As far as the authors know none of compressors have achieved such efficiency. The principles and methods of gas-dynamic design are presented below. The data of the 32 MW compressor presented by the customer in their report at the 16th International Compressor conference (September 2014, Saint- Petersburg) and later transferred to the authors.

An Agent-Based Modeling Framework and Application for the Generic Nuclear Fuel Cycle

NASA Astrophysics Data System (ADS)

Gidden, Matthew J.

Key components of a novel methodology and implementation of an agent-based, dynamic nuclear fuel cycle simulator, Cyclus , are presented. The nuclear fuel cycle is a complex, physics-dependent supply chain. To date, existing dynamic simulators have not treated constrained fuel supply, time-dependent, isotopic-quality based demand, or fuel fungibility particularly well. Utilizing an agent-based methodology that incorporates sophisticated graph theory and operations research techniques can overcome these deficiencies. This work describes a simulation kernel and agents that interact with it, highlighting the Dynamic Resource Exchange (DRE), the supply-demand framework at the heart of the kernel. The key agent-DRE interaction mechanisms are described, which enable complex entity interaction through the use of physics and socio-economic models. The translation of an exchange instance to a variant of the Multicommodity Transportation Problem, which can be solved feasibly or optimally, follows. An extensive investigation of solution performance and fidelity is then presented. Finally, recommendations for future users of Cyclus and the DRE are provided.

Multiscale modeling of current-induced switching in magnetic tunnel junctions using ab initio spin-transfer torques

NASA Astrophysics Data System (ADS)

Ellis, Matthew O. A.; Stamenova, Maria; Sanvito, Stefano

2017-12-01

There exists a significant challenge in developing efficient magnetic tunnel junctions with low write currents for nonvolatile memory devices. With the aim of analyzing potential materials for efficient current-operated magnetic junctions, we have developed a multi-scale methodology combining ab initio calculations of spin-transfer torque with large-scale time-dependent simulations using atomistic spin dynamics. In this work we introduce our multiscale approach, including a discussion on a number of possible schemes for mapping the ab initio spin torques into the spin dynamics. We demonstrate this methodology on a prototype Co/MgO/Co/Cu tunnel junction showing that the spin torques are primarily acting at the interface between the Co free layer and MgO. Using spin dynamics we then calculate the reversal switching times for the free layer and the critical voltages and currents required for such switching. Our work provides an efficient, accurate, and versatile framework for designing novel current-operated magnetic devices, where all the materials details are taken into account.

Automated chemical kinetic modeling via hybrid reactive molecular dynamics and quantum chemistry simulations.

PubMed

Döntgen, Malte; Schmalz, Felix; Kopp, Wassja A; Kröger, Leif C; Leonhard, Kai

2018-06-13

An automated scheme for obtaining chemical kinetic models from scratch using reactive molecular dynamics and quantum chemistry simulations is presented. This methodology combines the phase space sampling of reactive molecular dynamics with the thermochemistry and kinetics prediction capabilities of quantum mechanics. This scheme provides the NASA polynomial and modified Arrhenius equation parameters for all species and reactions that are observed during the simulation and supplies them in the ChemKin format. The ab initio level of theory for predictions is easily exchangeable and the presently used G3MP2 level of theory is found to reliably reproduce hydrogen and methane oxidation thermochemistry and kinetics data. Chemical kinetic models obtained with this approach are ready-to-use for, e.g., ignition delay time simulations, as shown for hydrogen combustion. The presented extension of the ChemTraYzer approach can be used as a basis for methodologically advancing chemical kinetic modeling schemes and as a black-box approach to generate chemical kinetic models.

Multi-Dielectric Brownian Dynamics and Design-Space-Exploration Studies of Permeation in Ion Channels.

PubMed

Siksik, May; Krishnamurthy, Vikram

2017-09-01

This paper proposes a multi-dielectric Brownian dynamics simulation framework for design-space-exploration (DSE) studies of ion-channel permeation. The goal of such DSE studies is to estimate the channel modeling-parameters that minimize the mean-squared error between the simulated and expected "permeation characteristics." To address this computational challenge, we use a methodology based on statistical inference that utilizes the knowledge of channel structure to prune the design space. We demonstrate the proposed framework and DSE methodology using a case study based on the KcsA ion channel, in which the design space is successfully reduced from a 6-D space to a 2-D space. Our results show that the channel dielectric map computed using the framework matches with that computed directly using molecular dynamics with an error of 7%. Finally, the scalability and resolution of the model used are explored, and it is shown that the memory requirements needed for DSE remain constant as the number of parameters (degree of heterogeneity) increases.

Geometric stiffening in multibody dynamics formulations

NASA Technical Reports Server (NTRS)

Sharf, Inna

1993-01-01

In this paper we discuss the issue of geometric stiffening as it arises in the context of multibody dynamics. This topic has been treated in a number of previous publications in this journal and appears to be a debated subject. The controversy revolves primarily around the 'correct' methodology for incorporating the stiffening effect into dynamics formulations. The main goal of this work is to present the different approaches that have been developed for this problem through an in-depth review of several publications dealing with this subject. This is done with the goal of contributing to a precise understanding of the existing methodologies for modelling the stiffening effects in multibody systems. Thus, in presenting the material we attempt to illuminate the key characteristics of the various methods as well as show how they relate to each other. In addition, we offer a number of novel insights and clarifying interpretations of these schemes. The paper is completed with a general classification and comparison of the different approaches.

A network-base analysis of CMIP5 "historical" experiments

NASA Astrophysics Data System (ADS)

Bracco, A.; Foudalis, I.; Dovrolis, C.

2012-12-01

In computer science, "complex network analysis" refers to a set of metrics, modeling tools and algorithms commonly used in the study of complex nonlinear dynamical systems. Its main premise is that the underlying topology or network structure of a system has a strong impact on its dynamics and evolution. By allowing to investigate local and non-local statistical interaction, network analysis provides a powerful, but only marginally explored, framework to validate climate models and investigate teleconnections, assessing their strength, range, and impacts on the climate system. In this work we propose a new, fast, robust and scalable methodology to examine, quantify, and visualize climate sensitivity, while constraining general circulation models (GCMs) outputs with observations. The goal of our novel approach is to uncover relations in the climate system that are not (or not fully) captured by more traditional methodologies used in climate science and often adopted from nonlinear dynamical systems analysis, and to explain known climate phenomena in terms of the network structure or its metrics. Our methodology is based on a solid theoretical framework and employs mathematical and statistical tools, exploited only tentatively in climate research so far. Suitably adapted to the climate problem, these tools can assist in visualizing the trade-offs in representing global links and teleconnections among different data sets. Here we present the methodology, and compare network properties for different reanalysis data sets and a suite of CMIP5 coupled GCM outputs. With an extensive model intercomparison in terms of the climate network that each model leads to, we quantify how each model reproduces major teleconnections, rank model performances, and identify common or specific errors in comparing model outputs and observations.

Evolution of a primary pulse in the granular dimers mounted on a linear elastic foundation: An analytical and numerical study.

PubMed

Ahsan, Zaid; Jayaprakash, K R

2016-10-01

In this exposition we consider the wave dynamics of a one-dimensional periodic granular dimer (diatomic) chain mounted on a damped and an undamped linear elastic foundation (otherwise called the on-site potential). It is very well known that periodic granular dimers support solitary wave propagation (similar to that in the homogeneous granular chains) for a specific discrete set of mass ratios. In this work we present the analytical investigation of the evolution of solitary waves and primary pulses in granular dimers when they are mounted on on-site potential with and without velocity proportional foundation damping. We invoke a methodology based on the multiple time-scale asymptotic analysis and partition the dynamics of the perturbed dimer chain into slow and fast components. The dynamics of the dimer chain in the limit of large mass mismatch (auxiliary chain) mounted on on-site potential and foundation damping is used as the basis for the analysis. A systematic analytical procedure is then developed for the slowly varying response of the beads and in estimating primary pulse amplitude evolution resulting in a nonlinear map relating the relative displacement amplitudes of two adjacent beads. The methodology is applicable for arbitrary mass ratios between the beads. We present several examples to demonstrate the efficacy of the proposed method. It is observed that the amplitude evolution predicted by the described methodology is in good agreement with the numerical simulation of the original system. This work forms a basis for further application of the considered methodology to weakly coupled granular dimers which finds practical relevance in designing shock mitigating granular layers.

Monte Carlo and Molecular Dynamics in the Multicanonical Ensemble: Connections between Wang-Landau Sampling and Metadynamics

NASA Astrophysics Data System (ADS)

Vogel, Thomas; Perez, Danny; Junghans, Christoph

2014-03-01

We show direct formal relationships between the Wang-Landau iteration [PRL 86, 2050 (2001)], metadynamics [PNAS 99, 12562 (2002)] and statistical temperature molecular dynamics [PRL 97, 050601 (2006)], the major Monte Carlo and molecular dynamics work horses for sampling from a generalized, multicanonical ensemble. We aim at helping to consolidate the developments in the different areas by indicating how methodological advancements can be transferred in a straightforward way, avoiding the parallel, largely independent, developments tracks observed in the past.

Integration of Computational Geometry, Finite Element, and Multibody System Algorithms for the Development of New Computational Methodology for High-Fidelity Vehicle Systems Modeling and Simulation

DTIC Science & Technology

2013-04-11

vehicle dynamics. Unclassified Unclassified Unclassified UU 9 Dr. Paramsothy Jayakumar (586) 282-4896 Computational Dynamics Inc.   0    Name of...Technical Representative Dr. Paramsothy Jayakumar TARDEC Computational Dynamics Inc.   1    Project Summary This project aims at addressing and...applications. This literature review is being summarized and incorporated into the paper. The commentary provided by Dr. Jayakumar was addressed and

Integration of Computational Geometry, Finite Element, and Multibody System Algorithms for the Development of New Computational Methodology for High-Fidelity Vehicle Systems Modeling and Simulation. ADDENDUM

DTIC Science & Technology

2013-11-12

Dr. Paramsothy Jayakumar (586) 282-4896 Computational Dynamics Inc.   0    Name of Contractor Computational Dynamics Inc. (CDI) 1809...Dr. Paramsothy Jayakumar TARDEC Computational Dynamics Inc.   1    Project Summary This project aims at addressing and remedying the serious...Shabana, A.A., Jayakumar , P., and Letherwood, M., “Soil Models and Vehicle System Dynamics”, Applied Mechanics Reviews, Vol. 65(4), 2013, doi

Adaptive resolution simulation of a biomolecule and its hydration shell: Structural and dynamical properties

NASA Astrophysics Data System (ADS)

Fogarty, Aoife C.; Potestio, Raffaello; Kremer, Kurt

2015-05-01

A fully atomistic modelling of many biophysical and biochemical processes at biologically relevant length- and time scales is beyond our reach with current computational resources, and one approach to overcome this difficulty is the use of multiscale simulation techniques. In such simulations, when system properties necessitate a boundary between resolutions that falls within the solvent region, one can use an approach such as the Adaptive Resolution Scheme (AdResS), in which solvent particles change their resolution on the fly during the simulation. Here, we apply the existing AdResS methodology to biomolecular systems, simulating a fully atomistic protein with an atomistic hydration shell, solvated in a coarse-grained particle reservoir and heat bath. Using as a test case an aqueous solution of the regulatory protein ubiquitin, we first confirm the validity of the AdResS approach for such systems, via an examination of protein and solvent structural and dynamical properties. We then demonstrate how, in addition to providing a computational speedup, such a multiscale AdResS approach can yield otherwise inaccessible physical insights into biomolecular function. We use our methodology to show that protein structure and dynamics can still be correctly modelled using only a few shells of atomistic water molecules. We also discuss aspects of the AdResS methodology peculiar to biomolecular simulations.

Poissonian steady states: from stationary densities to stationary intensities.

PubMed

Eliazar, Iddo

2012-10-01

Markov dynamics are the most elemental and omnipresent form of stochastic dynamics in the sciences, with applications ranging from physics to chemistry, from biology to evolution, and from economics to finance. Markov dynamics can be either stationary or nonstationary. Stationary Markov dynamics represent statistical steady states and are quantified by stationary densities. In this paper, we generalize the notion of steady state to the case of general Markov dynamics. Considering an ensemble of independent motions governed by common Markov dynamics, we establish that the entire ensemble attains Poissonian steady states which are quantified by stationary Poissonian intensities and which hold valid also in the case of nonstationary Markov dynamics. The methodology is applied to a host of Markov dynamics, including Brownian motion, birth-death processes, random walks, geometric random walks, renewal processes, growth-collapse dynamics, decay-surge dynamics, Ito diffusions, and Langevin dynamics.

Poissonian steady states: From stationary densities to stationary intensities

NASA Astrophysics Data System (ADS)

Eliazar, Iddo

2012-10-01

Markov dynamics are the most elemental and omnipresent form of stochastic dynamics in the sciences, with applications ranging from physics to chemistry, from biology to evolution, and from economics to finance. Markov dynamics can be either stationary or nonstationary. Stationary Markov dynamics represent statistical steady states and are quantified by stationary densities. In this paper, we generalize the notion of steady state to the case of general Markov dynamics. Considering an ensemble of independent motions governed by common Markov dynamics, we establish that the entire ensemble attains Poissonian steady states which are quantified by stationary Poissonian intensities and which hold valid also in the case of nonstationary Markov dynamics. The methodology is applied to a host of Markov dynamics, including Brownian motion, birth-death processes, random walks, geometric random walks, renewal processes, growth-collapse dynamics, decay-surge dynamics, Ito diffusions, and Langevin dynamics.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, La Tonya; Malczynski, Leonard

A Powersim Studio implementation of the system dynamics’ ‘Molecules of Structure’. The original implementation was in Ventana’s Vensim language by James Hines. The molecules are fundamental constructs of the system dynamics simulation methodology.

The Methodological Illumination of a Blind Spot: Information and Communication Technology and International Research Team Dynamics in a Higher Education Research Program

ERIC Educational Resources Information Center

Hoffman, David M.; Blasi, Brigida; Culum, Bojana; Dragšic, Žarko; Ewen, Amy; Horta, Hugo; Nokkala, Terhi; Rios-Aguilar, Cecilia

2014-01-01

This "self-ethnography" complements the other articles in this special issue by spotlighting a set of key challenges facing international research teams. The study is focused on the relationship between information and communication technology (ICT)-based collaboration and research team dynamics. Our diverse team, drawn from researchers…

Clay Caterpillar Whodunit: A Customizable Method for Studying Predator-Prey Interactions in the Field

ERIC Educational Resources Information Center

Curtis, Rachel; Klemens, Jeffrey A.; Agosta, Salvatore J.; Bartlow, Andrew W.; Wood, Steve; Carlson, Jason A.; Stratford, Jeffrey A.; Steele, Michael A.

2013-01-01

Predator-prey dynamics are an important concept in ecology, often serving as an introduction to the field of community ecology. However, these dynamics are difficult for students to observe directly. We describe a methodology that employs model caterpillars made of clay to estimate rates of predator attack on a prey species. This approach can be…

Qualitative Research and Educational Leadership: Essential Dynamics to Consider When Designing and Conducting Studies

ERIC Educational Resources Information Center

Brooks, Jeffrey S.; Normore, Anthony H.

2015-01-01

Purpose: The purpose of this paper is to highlight issues relayed to appropriate design and conduct of qualitative studies in educational leadership. Design/Methodology/Approach: The paper is a conceptual/logical argument that centers around the notion that while scholars in the field have at times paid attention to such dynamics, it is important…

Application of a Dynamic Programming Algorithm for Weapon Target Assignment

DTIC Science & Technology

2016-02-01

25] A . Turan , “Techniques for the Allocation of Resources Under Uncertainty,” Middle Eastern Technical University, Ankara, Turkey, 2012. [26] K...UNCLASSIFIED UNCLASSIFIED Application of a Dynamic Programming Algorithm for Weapon Target Assignment Lloyd Hammond Weapons and...optimisation techniques to support the decision making process. This report documents the methodology used to identify, develop and assess a

MODEL-Based Methodology for System of Systems Architecture Development with Application to the Recapitalization of the Future Towing and Salvage Platform

DTIC Science & Technology

2008-09-01

SEP) is a comprehensive , iterative and recursive problem solving process, applied sequentially top-down by integrated teams. It transforms needs...central integrated design repository. It includes a comprehensive behavior modeling notation to understand the dynamics of a design. CORE is a MBSE...37 F. DYNAMIC POSITIONING..........................................................................38 G. FIREFIGHTING

Dynamic analysis of news streams: institutional versus environmental effects.

PubMed

Dooley, Kevin; Corman, Steven

2004-07-01

Many societal phenomena are studied through analysis of their representation in media-related texts, such as news articles. The dynamics of such data reflect the phenomenon's underlying generative mechanism. Media artifacts are assumed to mirror the social activity occurring in the environment, thus observed dynamics are assumed to reflect environmental dynamics. The institutional mechanics of media production also affect the observed dynamics however. In this study we examine the extent to which institutional versus environmental effects explain the observed dynamics of media content, in particular focusing on semi-continuous "news streams". We examine the dynamics of news streams produced by the electronic news organization Reuters, immediately following the events of September 11, 2001. We find that many of the observed dynamics appear institutionally generated. We conclude with methodological suggestions concerning the dynamic analysis of media content.

Testability of evolutionary game dynamics based on experimental economics data

NASA Astrophysics Data System (ADS)

Wang, Yijia; Chen, Xiaojie; Wang, Zhijian

2017-11-01

Understanding the dynamic processes of a real game system requires an appropriate dynamics model, and rigorously testing a dynamics model is nontrivial. In our methodological research, we develop an approach to testing the validity of game dynamics models that considers the dynamic patterns of angular momentum and speed as measurement variables. Using Rock-Paper-Scissors (RPS) games as an example, we illustrate the geometric patterns in the experiment data. We then derive the related theoretical patterns from a series of typical dynamics models. By testing the goodness-of-fit between the experimental and theoretical patterns, we show that the validity of these models can be evaluated quantitatively. Our approach establishes a link between dynamics models and experimental systems, which is, to the best of our knowledge, the most effective and rigorous strategy for ascertaining the testability of evolutionary game dynamics models.

Tethered particle analysis of supercoiled circular DNA using peptide nucleic acid handles.

PubMed

Norregaard, Kamilla; Andersson, Magnus; Nielsen, Peter Eigil; Brown, Stanley; Oddershede, Lene B

2014-09-01

This protocol describes how to monitor individual naturally supercoiled circular DNA plasmids bound via peptide nucleic acid (PNA) handles between a bead and a surface. The protocol was developed for single-molecule investigation of the dynamics of supercoiled DNA, and it allows the investigation of both the dynamics of the molecule itself and of its interactions with a regulatory protein. Two bis-PNA clamps designed to bind with extremely high affinity to predetermined homopurine sequence sites in supercoiled DNA are prepared: one conjugated with digoxigenin for attachment to an anti-digoxigenin-coated glass cover slide, and one conjugated with biotin for attachment to a submicron-sized streptavidin-coated polystyrene bead. Plasmids are constructed, purified and incubated with the PNA handles. The dynamics of the construct is analyzed by tracking the tethered bead using video microscopy: less supercoiling results in more movement, and more supercoiling results in less movement. In contrast to other single-molecule methodologies, the current methodology allows for studying DNA in its naturally supercoiled state with constant linking number and constant writhe. The protocol has potential for use in studying the influence of supercoils on the dynamics of DNA and its associated proteins, e.g., topoisomerase. The procedure takes ~4 weeks.

Comparative study of the vapor analytes of trinitrotoluene (TNT)

NASA Astrophysics Data System (ADS)

Edge, Cindy C.; Gibb, Julie; Dugan, Regina E.

1998-12-01

Trinitrotoluene (TNT) is a high explosive used in most antipersonnel and antitank landmines. The Institute for Biological Detection Systems (IBDS) has developed a quantitative vapor delivery system, termed olfactometer, for conducting canine olfactory research. The research is conducted utilizing dynamic conditions, therefore, it is imperative to evaluate the headspace of TNT to ensure consistency with the dynamic generation of vapor. This study quantified the vapor headspace of military- grade TNT utilizing two different vapor generated methodologies, static and dynamic, reflecting differences between field and laboratory environments. Static vapor collection, which closely mimics conditions found during field detection, is defined as vapor collected in an open-air environment at ambient temperature. Dynamic vapor collection incorporates trapping of gases from a high flow vapor generation cell used during olfactometer operation. Analysis of samples collected by the two methodologies was performed by gas chromatography/mass spectrometry and the results provided information with regard to the constituents detected. However, constituent concentration did vary between the sampling methods. This study provides essential information regarding the vapor constituents associated with the TNT sampled using different sampling methods. These differences may be important in determining the detection signature dogs use to recognize TNT.

Experimental Determination of the Dynamic Hydraulic Transfer Function for the J-2X Oxidizer Turbopump. Part One; Methodology

NASA Technical Reports Server (NTRS)

Zoladz, Tom; Patel, Sandeep; Lee, Erik; Karon, Dave

2011-01-01

An advanced methodology for extracting the hydraulic dynamic pump transfer matrix (Yp) for a cavitating liquid rocket engine turbopump inducer+impeller has been developed. The transfer function is required for integrated vehicle pogo stability analysis as well as optimization of local inducer pumping stability. Laboratory pulsed subscale waterflow test of the J-2X oxygen turbo pump is introduced and our new extraction method applied to the data collected. From accurate measures of pump inlet and discharge perturbational mass flows and pressures, and one-dimensional flow models that represents complete waterflow loop physics, we are able to derive Yp and hence extract the characteristic pump parameters: compliance, pump gain, impedance, mass flow gain. Detailed modeling is necessary to accurately translate instrument plane measurements to the pump inlet and discharge and extract Yp. We present the MSFC Dynamic Lump Parameter Fluid Model Framework and describe critical dynamic component details. We report on fit minimization techniques, cost (fitness) function derivation, and resulting model fits to our experimental data are presented. Comparisons are made to alternate techniques for spatially translating measurement stations to actual pump inlet and discharge.

Thirteenth Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion and Launch Vehicle Technology. Volume 2

NASA Technical Reports Server (NTRS)

Williams, R. W. (Compiler)

1996-01-01

This conference publication includes various abstracts and presentations given at the 13th Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion and Launch Vehicle Technology held at the George C. Marshall Space Flight Center April 25-27 1995. The purpose of the workshop was to discuss experimental and computational fluid dynamic activities in rocket propulsion and launch vehicles. The workshop was an open meeting for government, industry, and academia. A broad number of topics were discussed including computational fluid dynamic methodology, liquid and solid rocket propulsion, turbomachinery, combustion, heat transfer, and grid generation.

Wavelet transform analysis of dynamic speckle patterns texture

NASA Astrophysics Data System (ADS)

Limia, Margarita Fernandez; Nunez, Adriana Mavilio; Rabal, Hector; Trivi, Marcelo

2002-11-01

We propose the use of the wavelet transform to characterize the time evolution of dynamic speckle patterns. We describe it by using as an example a method used for the assessment of the drying of paint. Optimal texture features are determined and the time evolution is described in terms of the Mahalanobis distance to the final (dry) state. From the behavior of this distance function, two parameters are defined that characterize the evolution. Because detailed knowledge of the involved dynamics is not required, the methodology could be implemented for other complex or poorly understood dynamic phenomena.

Controlling allosteric networks in proteins

NASA Astrophysics Data System (ADS)

Dokholyan, Nikolay

2013-03-01

We present a novel methodology based on graph theory and discrete molecular dynamics simulations for delineating allosteric pathways in proteins. We use this methodology to uncover the structural mechanisms responsible for coupling of distal sites on proteins and utilize it for allosteric modulation of proteins. We will present examples where inference of allosteric networks and its rewiring allows us to ``rescue'' cystic fibrosis transmembrane conductance regulator (CFTR), a protein associated with fatal genetic disease cystic fibrosis. We also use our methodology to control protein function allosterically. We design a novel protein domain that can be inserted into identified allosteric site of target protein. Using a drug that binds to our domain, we alter the function of the target protein. We successfully tested this methodology in vitro, in living cells and in zebrafish. We further demonstrate transferability of our allosteric modulation methodology to other systems and extend it to become ligh-activatable.

Explosion/Blast Dynamics for Constellation Launch Vehicles Assessment

NASA Technical Reports Server (NTRS)

Baer, Mel; Crawford, Dave; Hickox, Charles; Kipp, Marlin; Hertel, Gene; Morgan, Hal; Ratzel, Arthur; Cragg, Clinton H.

2009-01-01

An assessment methodology is developed to guide quantitative predictions of adverse physical environments and the subsequent effects on the Ares-1 crew launch vehicle associated with the loss of containment of cryogenic liquid propellants from the upper stage during ascent. Development of the methodology is led by a team at Sandia National Laboratories (SNL) with guidance and support from a number of National Aeronautics and Space Administration (NASA) personnel. The methodology is based on the current Ares-1 design and feasible accident scenarios. These scenarios address containment failure from debris impact or structural response to pressure or blast loading from an external source. Once containment is breached, the envisioned assessment methodology includes predictions for the sequence of physical processes stemming from cryogenic tank failure. The investigative techniques, analysis paths, and numerical simulations that comprise the proposed methodology are summarized and appropriate simulation software is identified in this report.

Predicting trends of invasive plants richness using local socio-economic data: An application in North Portugal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santos, Mario, E-mail: mgsantoss@gmail.com; Freitas, Raul, E-mail: raulfreitas@portugalmail.com; Crespi, Antonio L., E-mail: aluis.crespi@gmail.com

2011-10-15

This study assesses the potential of an integrated methodology for predicting local trends in invasive exotic plant species (invasive richness) using indirect, regional information on human disturbance. The distribution of invasive plants was assessed in North Portugal using herbarium collections and local environmental, geophysical and socio-economic characteristics. Invasive richness response to anthropogenic disturbance was predicted using a dynamic model based on a sequential modeling process (stochastic dynamic methodology-StDM). Derived scenarios showed that invasive richness trends were clearly associated with ongoing socio-economic change. Simulations including scenarios of growing urbanization showed an increase in invasive richness while simulations in municipalities with decreasingmore » populations showed stable or decreasing levels of invasive richness. The model simulations demonstrate the interest and feasibility of using this methodology in disturbance ecology. - Highlights: {yields} Socio-economic data indicate human induced disturbances. {yields} Socio-economic development increase disturbance in ecosystems. {yields} Disturbance promotes opportunities for invasive plants.{yields} Increased opportunities promote richness of invasive plants.{yields} Increase in richness of invasive plants change natural ecosystems.« less

High Accuracy Liquid Propellant Slosh Predictions Using an Integrated CFD and Controls Analysis Interface

NASA Technical Reports Server (NTRS)

Marsell, Brandon; Griffin, David; Schallhorn, Dr. Paul; Roth, Jacob

2012-01-01

Coupling computational fluid dynamics (CFD) with a controls analysis tool elegantly allows for high accuracy predictions of the interaction between sloshing liquid propellants and th e control system of a launch vehicle. Instead of relying on mechanical analogs which are not valid during aU stages of flight, this method allows for a direct link between the vehicle dynamic environments calculated by the solver in the controls analysis tool to the fluid flow equations solved by the CFD code. This paper describes such a coupling methodology, presents the results of a series of test cases, and compares said results against equivalent results from extensively validated tools. The coupling methodology, described herein, has proven to be highly accurate in a variety of different cases.

Integrated CFD and Controls Analysis Interface for High Accuracy Liquid Propellant Slosh Predictions

NASA Technical Reports Server (NTRS)

Marsell, Brandon; Griffin, David; Schallhorn, Paul; Roth, Jacob

2012-01-01

Coupling computational fluid dynamics (CFD) with a controls analysis tool elegantly allows for high accuracy predictions of the interaction between sloshing liquid propellants and the control system of a launch vehicle. Instead of relying on mechanical analogs which are n0t va lid during all stages of flight, this method allows for a direct link between the vehicle dynamic environments calculated by the solver in the controls analysis tool to the fluid now equations solved by the CFD code. This paper describes such a coupling methodology, presents the results of a series of test cases, and compares said results against equivalent results from extensively validated tools. The coupling methodology, described herein, has proven to be highly accurate in a variety of different cases.

The Shock and Vibration Bulletin. Part 1. Welcome, Keynote Address, Invited Papers, Pyrotechnic Shock, and Shock Testing and Analysis

DTIC Science & Technology

1983-05-01

DESIGN PROCEDURE M. S. IIAndal, University of Vermont, Burlington, VT Machinery Dynamics ANALYTICAL AND EXPERIMENTAL INVESTIGATION OF ROTATING BLADE... methodology to accurately predict rotor vibratory loads and has recently been initiated for detail design and bench test- coupled rotor/airframe vibrations... design methodology , a trating on the basic disciplines of aerodynamics and struc. coupled rotor/airframe vibration analysis has been developed. tural

Evaluating Multi-Input/Multi-Output Digital Control Systems

NASA Technical Reports Server (NTRS)

Pototzky, Anthony S.; Wieseman, Carol D.; Hoadley, Sherwood T.; Mukhopadhyay, Vivek

1994-01-01

Controller-performance-evaluation (CPE) methodology for multi-input/multi-output (MIMO) digital control systems developed. Procedures identify potentially destabilizing controllers and confirm satisfactory performance of stabilizing ones. Methodology generic and used in many types of multi-loop digital-controller applications, including digital flight-control systems, digitally controlled spacecraft structures, and actively controlled wind-tunnel models. Also applicable to other complex, highly dynamic digital controllers, such as those in high-performance robot systems.

System Dynamics Modeling for Public Health: Background and Opportunities

PubMed Central

Homer, Jack B.; Hirsch, Gary B.

2006-01-01

The systems modeling methodology of system dynamics is well suited to address the dynamic complexity that characterizes many public health issues. The system dynamics approach involves the development of computer simulation models that portray processes of accumulation and feedback and that may be tested systematically to find effective policies for overcoming policy resistance. System dynamics modeling of chronic disease prevention should seek to incorporate all the basic elements of a modern ecological approach, including disease outcomes, health and risk behaviors, environmental factors, and health-related resources and delivery systems. System dynamics shows promise as a means of modeling multiple interacting diseases and risks, the interaction of delivery systems and diseased populations, and matters of national and state policy. PMID:16449591

Research and development activities in unified control-structure modeling and design

NASA Technical Reports Server (NTRS)

Nayak, A. P.

1985-01-01

Results of work to develop a unified control/structures modeling and design capability for large space structures modeling are presented. Recent analytical results are presented to demonstrate the significant interdependence between structural and control properties. A new design methodology is suggested in which the structure, material properties, dynamic model and control design are all optimized simultaneously. Parallel research done by other researchers is reviewed. The development of a methodology for global design optimization is recommended as a long-term goal. It is suggested that this methodology should be incorporated into computer aided engineering programs, which eventually will be supplemented by an expert system to aid design optimization.

General implementation of arbitrary nonlinear quadrature phase gates

NASA Astrophysics Data System (ADS)

Marek, Petr; Filip, Radim; Ogawa, Hisashi; Sakaguchi, Atsushi; Takeda, Shuntaro; Yoshikawa, Jun-ichi; Furusawa, Akira

2018-02-01

We propose general methodology of deterministic single-mode quantum interaction nonlinearly modifying single quadrature variable of a continuous-variable system. The methodology is based on linear coupling of the system to ancillary systems subsequently measured by quadrature detectors. The nonlinear interaction is obtained by using the data from the quadrature detection for dynamical manipulation of the coupling parameters. This measurement-induced methodology enables direct realization of arbitrary nonlinear quadrature interactions without the need to construct them from the lowest-order gates. Such nonlinear interactions are crucial for more practical and efficient manipulation of continuous quadrature variables as well as qubits encoded in continuous-variable systems.

Flight Dynamics Operations: Methods and Lessons Learned from Space Shuttle Orbit Operations

NASA Technical Reports Server (NTRS)

Cutri-Kohart, Rebecca M.

2011-01-01

The Flight Dynamics Officer is responsible for trajectory maintenance of the Space Shuttle. This paper will cover high level operational considerations, methodology, procedures, and lessons learned involved in performing the functions of orbit and rendezvous Flight Dynamics Officer and leading the team of flight dynamics specialists during different phases of flight. The primary functions that will be address are: onboard state vector maintenance, ground ephemeris maintenance, calculation of ground and spacecraft acquisitions, collision avoidance, burn targeting for the primary mission, rendezvous, deorbit and contingencies, separation sequences, emergency deorbit preparation, mass properties coordination, payload deployment planning, coordination with the International Space Station, and coordination with worldwide trajectory customers. Each of these tasks require the Flight Dynamics Officer to have cognizance of the current trajectory state as well as the impact of future events on the trajectory plan in order to properly analyze and react to real-time changes. Additionally, considerations are made to prepare flexible alternative trajectory plans in the case timeline changes or a systems failure impact the primary plan. The evolution of the methodology, procedures, and techniques used by the Flight Dynamics Officer to perform these tasks will be discussed. Particular attention will be given to how specific Space Shuttle mission and training simulation experiences, particularly off-nominal or unexpected events such as shortened mission durations, tank failures, contingency deorbit, navigation errors, conjunctions, and unexpected payload deployments, have influenced the operational procedures and training for performing Space Shuttle flight dynamics operations over the history of the program. These lessons learned can then be extended to future vehicle trajectory operations.

Solution NMR views of dynamical ordering of biomacromolecules.

PubMed

Ikeya, Teppei; Ban, David; Lee, Donghan; Ito, Yutaka; Kato, Koichi; Griesinger, Christian

2018-02-01

To understand the mechanisms related to the 'dynamical ordering' of macromolecules and biological systems, it is crucial to monitor, in detail, molecular interactions and their dynamics across multiple timescales. Solution nuclear magnetic resonance (NMR) spectroscopy is an ideal tool that can investigate biophysical events at the atomic level, in near-physiological buffer solutions, or even inside cells. In the past several decades, progress in solution NMR has significantly contributed to the elucidation of three-dimensional structures, the understanding of conformational motions, and the underlying thermodynamic and kinetic properties of biomacromolecules. This review discusses recent methodological development of NMR, their applications and some of the remaining challenges. Although a major drawback of NMR is its difficulty in studying the dynamical ordering of larger biomolecular systems, current technologies have achieved considerable success in the structural analysis of substantially large proteins and biomolecular complexes over 1MDa and have characterised a wide range of timescales across which biomolecular motion exists. While NMR is well suited to obtain local structure information in detail, it contributes valuable and unique information within hybrid approaches that combine complementary methodologies, including solution scattering and microscopic techniques. For living systems, the dynamic assembly and disassembly of macromolecular complexes is of utmost importance for cellular homeostasis and, if dysregulated, implied in human disease. It is thus instructive for the advancement of the study of the dynamical ordering to discuss the potential possibilities of solution NMR spectroscopy and its applications. This article is part of a Special Issue entitled "Biophysical Exploration of Dynamical Ordering of Biomolecular Systems" edited by Dr. Koichi Kato. Copyright © 2017 Elsevier B.V. All rights reserved.

High-rate RTK and PPP multi-GNSS positioning for small-scale dynamic displacements monitoring

NASA Astrophysics Data System (ADS)

Paziewski, Jacek; Sieradzki, Rafał; Baryła, Radosław; Wielgosz, Pawel

2017-04-01

The monitoring of dynamic displacements and deformations of engineering structures such as buildings, towers and bridges is of great interest due to several practical and theoretical reasons. The most important is to provide information required for safe maintenance of the constructions. High temporal resolution and precision of GNSS observations predestine this technology to be applied to most demanding application in terms of accuracy, availability and reliability. GNSS technique supported by appropriate processing methodology may meet the specific demands and requirements of ground and structures monitoring. Thus, high-rate multi-GNSS signals may be used as reliable source of information on dynamic displacements of ground and engineering structures, also in real time applications. In this study we present initial results of application of precise relative GNSS positioning for detection of small scale (cm level) high temporal resolution dynamic displacements. Methodology and algorithms applied in self-developed software allowing for relative positioning using high-rate dual-frequency phase and pseudorange GPS+Galileo observations are also given. Additionally, an approach was also made to use the Precise Point Positioning technique to such application. In the experiment were used the observations obtained from high-rate (20 Hz) geodetic receivers. The dynamic displacements were simulated using specially constructed device moving GNSS antenna with dedicated amplitude and frequency. The obtained results indicate on possibility of detection of dynamic displacements of the GNSS antenna even at the level of few millimetres using both relative and Precise Point Positioning techniques after suitable signals processing.

Dynamic Loads Generation for Multi-Point Vibration Excitation Problems

NASA Technical Reports Server (NTRS)

Shen, Lawrence

2011-01-01

A random-force method has been developed to predict dynamic loads produced by rocket-engine random vibrations for new rocket-engine designs. The method develops random forces at multiple excitation points based on random vibration environments scaled from accelerometer data obtained during hot-fire tests of existing rocket engines. This random-force method applies random forces to the model and creates expected dynamic response in a manner that simulates the way the operating engine applies self-generated random vibration forces (random pressure acting on an area) with the resulting responses that we measure with accelerometers. This innovation includes the methodology (implementation sequence), the computer code, two methods to generate the random-force vibration spectra, and two methods to reduce some of the inherent conservatism in the dynamic loads. This methodology would be implemented to generate the random-force spectra at excitation nodes without requiring the use of artificial boundary conditions in a finite element model. More accurate random dynamic loads than those predicted by current industry methods can then be generated using the random force spectra. The scaling method used to develop the initial power spectral density (PSD) environments for deriving the random forces for the rocket engine case is based on the Barrett Criteria developed at Marshall Space Flight Center in 1963. This invention approach can be applied in the aerospace, automotive, and other industries to obtain reliable dynamic loads and responses from a finite element model for any structure subject to multipoint random vibration excitations.

Estimating rates of local extinction and colonization in colonial species and an extension to the metapopulation and community levels

USGS Publications Warehouse

Barbraud, C.; Nichols, J.D.; Hines, J.E.; Hafner, H.

2003-01-01

Coloniality has mainly been studied from an evolutionary perspective, but relatively few studies have developed methods for modelling colony dynamics. Changes in number of colonies over time provide a useful tool for predicting and evaluating the responses of colonial species to management and to environmental disturbance. Probabilistic Markov process models have been recently used to estimate colony site dynamics using presence-absence data when all colonies are detected in sampling efforts. Here, we define and develop two general approaches for the modelling and analysis of colony dynamics for sampling situations in which all colonies are, and are not, detected. For both approaches, we develop a general probabilistic model for the data and then constrain model parameters based on various hypotheses about colony dynamics. We use Akaike's Information Criterion (AIC) to assess the adequacy of the constrained models. The models are parameterised with conditional probabilities of local colony site extinction and colonization. Presence-absence data arising from Pollock's robust capture-recapture design provide the basis for obtaining unbiased estimates of extinction, colonization, and detection probabilities when not all colonies are detected. This second approach should be particularly useful in situations where detection probabilities are heterogeneous among colony sites. The general methodology is illustrated using presence-absence data on two species of herons (Purple Heron, Ardea purpurea and Grey Heron, Ardea cinerea). Estimates of the extinction and colonization rates showed interspecific differences and strong temporal and spatial variations. We were also able to test specific predictions about colony dynamics based on ideas about habitat change and metapopulation dynamics. We recommend estimators based on probabilistic modelling for future work on colony dynamics. We also believe that this methodological framework has wide application to problems in animal ecology concerning metapopulation and community dynamics.

Closed-form dynamics of a hexarot parallel manipulator by means of the principle of virtual work

NASA Astrophysics Data System (ADS)

Pedrammehr, Siamak; Nahavandi, Saeid; Abdi, Hamid

2018-04-01

In this research, a systematic approach to solving the inverse dynamics of hexarot manipulators is addressed using the methodology of virtual work. For the first time, a closed form of the mathematical formulation of the standard dynamic model is presented for this class of mechanisms. An efficient algorithm for solving this closed-form dynamic model of the mechanism is developed and it is used to simulate the dynamics of the system for different trajectories. Validation of the proposed model is performed using SimMechanics and it is shown that the results of the proposed mathematical model match with the results obtained by the SimMechanics model.

Dynamic loading and stress life analysis of permanent space station modules

NASA Astrophysics Data System (ADS)

Anisimov, A. V.; Krokhin, I. A.; Likhoded, A. I.; Malinin, A. A.; Panichkin, N. G.; Sidorov, V. V.; Titov, V. A.

2016-11-01

Some methodological approaches to solving several key problems of dynamic loading and structural strength analysis of Permanent Space Station (PSS)modules developed on the basis of the working experience of Soviet and Russian PSS and the International Space station (ISS) are presented. The solutions of the direct and semi-inverse problems of PSS structure dynamics are mathematically stated. Special attention is paid to the use of the results of ground structural strength tests of space station modules and the data on the actual flight actions on the station and its dynamic responses in the orbital operation regime. The procedure of determining the dynamics and operation life parameters of elements of the PSS modules is described.

Computational fluid dynamics for propulsion technology: Geometric grid visualization in CFD-based propulsion technology research

NASA Technical Reports Server (NTRS)

Ziebarth, John P.; Meyer, Doug

1992-01-01

The coordination is examined of necessary resources, facilities, and special personnel to provide technical integration activities in the area of computational fluid dynamics applied to propulsion technology. Involved is the coordination of CFD activities between government, industry, and universities. Current geometry modeling, grid generation, and graphical methods are established to use in the analysis of CFD design methodologies.

Re-Assessing Poverty Dynamics and State Protections in Britain and the US: The Role of Measurement Error

ERIC Educational Resources Information Center

Worts, Diana; Sacker, Amanda; McDonough, Peggy

2010-01-01

This paper addresses a key methodological challenge in the modeling of individual poverty dynamics--the influence of measurement error. Taking the US and Britain as case studies and building on recent research that uses latent Markov models to reduce bias, we examine how measurement error can affect a range of important poverty estimates. Our data…

Classification of small lesions on dynamic breast MRI: Integrating dimension reduction and out-of-sample extension into CADx methodology

PubMed Central

Nagarajan, Mahesh B.; Huber, Markus B.; Schlossbauer, Thomas; Leinsinger, Gerda; Krol, Andrzej; Wismüller, Axel

2014-01-01

Objective While dimension reduction has been previously explored in computer aided diagnosis (CADx) as an alternative to feature selection, previous implementations of its integration into CADx do not ensure strict separation between training and test data required for the machine learning task. This compromises the integrity of the independent test set, which serves as the basis for evaluating classifier performance. Methods and Materials We propose, implement and evaluate an improved CADx methodology where strict separation is maintained. This is achieved by subjecting the training data alone to dimension reduction; the test data is subsequently processed with out-of-sample extension methods. Our approach is demonstrated in the research context of classifying small diagnostically challenging lesions annotated on dynamic breast magnetic resonance imaging (MRI) studies. The lesions were dynamically characterized through topological feature vectors derived from Minkowski functionals. These feature vectors were then subject to dimension reduction with different linear and non-linear algorithms applied in conjunction with out-of-sample extension techniques. This was followed by classification through supervised learning with support vector regression. Area under the receiver-operating characteristic curve (AUC) was evaluated as the metric of classifier performance. Results Of the feature vectors investigated, the best performance was observed with Minkowski functional ’perimeter’ while comparable performance was observed with ’area’. Of the dimension reduction algorithms tested with ’perimeter’, the best performance was observed with Sammon’s mapping (0.84 ± 0.10) while comparable performance was achieved with exploratory observation machine (0.82 ± 0.09) and principal component analysis (0.80 ± 0.10). Conclusions The results reported in this study with the proposed CADx methodology present a significant improvement over previous results reported with such small lesions on dynamic breast MRI. In particular, non-linear algorithms for dimension reduction exhibited better classification performance than linear approaches, when integrated into our CADx methodology. We also note that while dimension reduction techniques may not necessarily provide an improvement in classification performance over feature selection, they do allow for a higher degree of feature compaction. PMID:24355697

Nonlinear Structural Analysis Methodology and Dynamics Scaling of Inflatable Parabolic Reflector Antenna Concepts

NASA Technical Reports Server (NTRS)

Sreekantamurthy, Tham; Gaspar, James L.; Mann, Troy; Behun, Vaughn; Pearson, James C., Jr.; Scarborough, Stephen

2007-01-01

Ultra-light weight and ultra-thin membrane inflatable antenna concepts are fast evolving to become the state-of-the-art antenna concepts for deep-space applications. NASA Langley Research Center has been involved in the structural dynamics research on antenna structures. One of the goals of the research is to develop structural analysis methodology for prediction of the static and dynamic response characteristics of the inflatable antenna concepts. This research is focused on the computational studies to use nonlinear large deformation finite element analysis to characterize the ultra-thin membrane responses of the antennas. Recently, structural analyses have been performed on a few parabolic reflector antennas of varying size and shape, which are referred in the paper as 0.3 meters subscale, 2 meters half-scale, and 4 meters full-scale antenna. The various aspects studied included nonlinear analysis methodology and solution techniques, ways to speed convergence in iterative methods, the sensitivities of responses with respect to structural loads, such as inflation pressure, gravity, and pretension loads in the ground and in-space conditions, and the ultra-thin membrane wrinkling characteristics. Several such intrinsic aspects studied have provided valuable insight into evaluation of structural characteristics of such antennas. While analyzing these structural characteristics, a quick study was also made to assess the applicability of dynamics scaling of the half-scale antenna. This paper presents the details of the nonlinear structural analysis results, and discusses the insight gained from the studies on the various intrinsic aspects of the analysis methodology. The predicted reflector surface characteristics of the three inflatable ultra-thin membrane parabolic reflector antenna concepts are presented as easily observable displacement fringe patterns with associated maximum values, and normal mode shapes and associated frequencies. Wrinkling patterns are presented to show how surface wrinkle progress with increasing tension loads. Antenna reflector surface accuracies were found to be very much dependent on the type and size of the antenna, the reflector surface curvature, reflector membrane supports in terms of spacing of catenaries, as well as the amount of applied load.

Design optimization of aircraft landing gear assembly under dynamic loading

NASA Astrophysics Data System (ADS)

Wong, Jonathan Y. B.

As development cycles and prototyping iterations begin to decrease in the aerospace industry, it is important to develop and improve practical methodologies to meet all design metrics. This research presents an efficient methodology that applies high-fidelity multi-disciplinary design optimization techniques to commercial landing gear assemblies, for weight reduction, cost savings, and structural performance dynamic loading. Specifically, a slave link subassembly was selected as the candidate to explore the feasibility of this methodology. The design optimization process utilized in this research was sectioned into three main stages: setup, optimization, and redesign. The first stage involved the creation and characterization of the models used throughout this research. The slave link assembly was modelled with a simplified landing gear test, replicating the behavior of the physical system. Through extensive review of the literature and collaboration with Safran Landing Systems, dynamic and structural behavior for the system were characterized and defined mathematically. Once defined, the characterized behaviors for the slave link assembly were then used to conduct a Multi-Body Dynamic (MBD) analysis to determine the dynamic and structural response of the system. These responses were then utilized in a topology optimization through the use of the Equivalent Static Load Method (ESLM). The results of the optimization were interpreted and later used to generate improved designs in terms of weight, cost, and structural performance under dynamic loading in stage three. The optimized designs were then validated using the model created for the MBD analysis of the baseline design. The design generation process employed two different approaches for post-processing the topology results produced. The first approach implemented a close replication of the topology results, resulting in a design with an overall peak stress increase of 74%, weight savings of 67%, and no apparent cost savings due to complex features present in the design. The second design approach focused on realizing reciprocating benefits for cost and weight savings. As a result, this design was able to achieve an overall peak stress increase of 6%, weight and cost savings of 36%, and 60%, respectively.

Dynamics of Coupled Electron-Boson Systems with the Multiple Davydov D1 Ansatz and the Generalized Coherent State.

PubMed

Chen, Lipeng; Borrelli, Raffaele; Zhao, Yang

2017-11-22

The dynamics of a coupled electron-boson system is investigated by employing a multitude of the Davydov D 1 trial states, also known as the multi-D 1 Ansatz, and a second trial state based on a superposition of the time-dependent generalized coherent state (GCS Ansatz). The two Ansätze are applied to study population dynamics in the spin-boson model and the Holstein molecular crystal model, and a detailed comparison with numerically exact results obtained by the (multilayer) multiconfiguration time-dependent Hartree method and the hierarchy equations of motion approach is drawn. It is found that the two methodologies proposed here have significantly improved over that with the single D 1 Ansatz, yielding quantitatively accurate results even in the critical cases of large energy biases and large transfer integrals. The two methodologies provide new effective tools for accurate, efficient simulation of many-body quantum dynamics thanks to a relatively small number of parameters which characterize the electron-nuclear wave functions. The wave-function-based approaches are capable of tracking explicitly detailed bosonic dynamics, which is absent by construct in approaches based on the reduced density matrix. The efficiency and flexibility of our methods are also advantages as compared with numerically exact approaches such as QUAPI and HEOM, especially at low temperatures and in the strong coupling regime.

[A method for forecasting the seasonal dynamic of malaria in the municipalities of Colombia].

PubMed

Velásquez, Javier Oswaldo Rodríguez

2010-03-01

To develop a methodology for forecasting the seasonal dynamic of malaria outbreaks in the municipalities of Colombia. Epidemiologic ranges were defined by multiples of 50 cases for the six municipalities with the highest incidence, 25 cases for the municipalities that ranked 10th and 11th by incidence, 10 for the municipality that ranked 193rd, and 5 for the municipality that ranked 402nd. The specific probability values for each epidemiologic range appearing in each municipality, as well as the S/k value--the ratio between entropy (S) and the Boltzmann constant (k)--were calculated for each three-week set, along with the differences in this ratio divided by the consecutive sets of weeks. These mathematical ratios were used to determine the values for forecasting the case dynamic, which were compared with the actual epidemiologic data from the period 2003-2007. The probability of the epidemiologic ranges appearing ranged from 0.019 and 1.00, while the differences in the S/k ratio between the sets of consecutive weeks ranged from 0.23 to 0.29. Three ratios were established to determine whether the dynamic corresponded to an outbreak. These ratios were corroborated with real epidemiological data from 810 Colombian municipalities. This methodology allows us to forecast the malaria case dynamic and outbreaks in the municipalities of Colombia and can be used in planning interventions and public health policies.

Challenges to inferring causality from viral information dispersion in dynamic social networks

NASA Astrophysics Data System (ADS)

Ternovski, John

2014-06-01

Understanding the mechanism behind large-scale information dispersion through complex networks has important implications for a variety of industries ranging from cyber-security to public health. With the unprecedented availability of public data from online social networks (OSNs) and the low cost nature of most OSN outreach, randomized controlled experiments, the "gold standard" of causal inference methodologies, have been used with increasing regularity to study viral information dispersion. And while these studies have dramatically furthered our understanding of how information disseminates through social networks by isolating causal mechanisms, there are still major methodological concerns that need to be addressed in future research. This paper delineates why modern OSNs are markedly different from traditional sociological social networks and why these differences present unique challenges to experimentalists and data scientists. The dynamic nature of OSNs is particularly troublesome for researchers implementing experimental designs, so this paper identifies major sources of bias arising from network mutability and suggests strategies to circumvent and adjust for these biases. This paper also discusses the practical considerations of data quality and collection, which may adversely impact the efficiency of the estimator. The major experimental methodologies used in the current literature on virality are assessed at length, and their strengths and limits identified. Other, as-yetunsolved threats to the efficiency and unbiasedness of causal estimators--such as missing data--are also discussed. This paper integrates methodologies and learnings from a variety of fields under an experimental and data science framework in order to systematically consolidate and identify current methodological limitations of randomized controlled experiments conducted in OSNs.

Temperature dynamics of stormwater runoff in Australia and the USA.

PubMed

Hathaway, J M; Winston, R J; Brown, R A; Hunt, W F; McCarthy, D T

2016-07-15

Thermal pollution of surface waters by urban stormwater runoff is an often overlooked by-product of urbanization. Elevated stream temperatures due to an influx of stormwater runoff can be detrimental to stream biota, in particular for cold water systems. However, few studies have examined temperature trends throughout storm events to determine how these thermal inputs are temporally distributed. In this study, six diverse catchments in two continents are evaluated for thermal dynamics. Summary statistics from the data showed larger catchments have lower maximum runoff temperatures, minimum runoff temperatures, and temperature variability. This reinforces the understanding that subsurface drainage infrastructure in urban catchments acts to moderate runoff temperatures. The catchments were also evaluated for the presence of a thermal first flush using two methodologies. Results showed the lack of a first flush under traditional assessment methodologies across all six catchments, supporting the results from a limited number of studies in literature. However, the time to peak temperature was not always coincident with the time to peak flow, highlighting the variability of thermal load over time. When a new first flush methodology was applied, significant differences in temperature were noted with increasing runoff depth for five of the six sites. This study is the first to identify a runoff temperature first flush, and highlights the need to carefully consider the appropriate methodology for such analyses. Copyright © 2016 Elsevier B.V. All rights reserved.

Approaching the investigation of plasma turbulence through a rigorous verification and validation procedure: A practical example

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ricci, P., E-mail: paolo.ricci@epfl.ch; Riva, F.; Theiler, C.

In the present work, a Verification and Validation procedure is presented and applied showing, through a practical example, how it can contribute to advancing our physics understanding of plasma turbulence. Bridging the gap between plasma physics and other scientific domains, in particular, the computational fluid dynamics community, a rigorous methodology for the verification of a plasma simulation code is presented, based on the method of manufactured solutions. This methodology assesses that the model equations are correctly solved, within the order of accuracy of the numerical scheme. The technique to carry out a solution verification is described to provide a rigorousmore » estimate of the uncertainty affecting the numerical results. A methodology for plasma turbulence code validation is also discussed, focusing on quantitative assessment of the agreement between experiments and simulations. The Verification and Validation methodology is then applied to the study of plasma turbulence in the basic plasma physics experiment TORPEX [Fasoli et al., Phys. Plasmas 13, 055902 (2006)], considering both two-dimensional and three-dimensional simulations carried out with the GBS code [Ricci et al., Plasma Phys. Controlled Fusion 54, 124047 (2012)]. The validation procedure allows progress in the understanding of the turbulent dynamics in TORPEX, by pinpointing the presence of a turbulent regime transition, due to the competition between the resistive and ideal interchange instabilities.« less

Application of hybrid methodology to rotors in steady and maneuvering flight

NASA Astrophysics Data System (ADS)

Rajmohan, Nischint

Helicopters are versatile flying machines that have capabilities that are unparalleled by fixed wing aircraft, such as operating in hover, performing vertical takeoff and landing on unprepared sites. This makes their use especially desirable in military and search-and-rescue operations. However, modern helicopters still suffer from high levels of noise and vibration caused by the physical phenomena occurring in the vicinity of the rotor blades. Therefore, improvement in rotorcraft design to reduce the noise and vibration levels requires understanding of the underlying physical phenomena, and accurate prediction capabilities of the resulting rotorcraft aeromechanics. The goal of this research is to study the aeromechanics of rotors in steady and maneuvering flight using hybrid Computational Fluid Dynamics (CFD) methodology. The hybrid CFD methodology uses the Navier-Stokes equations to solve the flow near the blade surface but the effect of the far wake is computed through the wake model. The hybrid CFD methodology is computationally efficient and its wake modeling approach is nondissipative making it an attractive tool to study rotorcraft aeromechanics. Several enhancements were made to the CFD methodology and it was coupled to a Computational Structural Dynamics (CSD) methodology to perform a trimmed aeroelastic analysis of a rotor in forward flight. The coupling analyses, both loose and tight were used to identify the key physical phenomena that affect rotors in different steady flight regimes. The modeling enhancements improved the airloads predictions for a variety of flight conditions. It was found that the tightly coupled method did not impact the loads significantly for steady flight conditions compared to the loosely coupled method. The coupling methodology was extended to maneuvering flight analysis by enhancing the computational and structural models to handle non-periodic flight conditions and vehicle motions in time accurate mode. The flight test control angles were employed to enable the maneuvering flight analysis. The fully coupled model provided the presence of three dynamic stall cycles on the rotor in maneuver. It is important to mention that analysis of maneuvering flight requires knowledge of the pilot input control pitch settings, and the vehicle states. As the result, these computational tools cannot be used for analysis of loads in a maneuver that has not been duplicated in a real flight. This is a significant limitation if these tools are to be selected during the design phase of a helicopter where its handling qualities are evaluated in different trajectories. Therefore, a methodology was developed to couple the CFD/CSD simulation with an inverse flight mechanics simulation to perform the maneuver analysis without using the flight test control input. The methodology showed reasonable convergence in steady flight regime and control angles predictions compared fairly well with test data. In the maneuvering flight regions, the convergence was slower due to relaxation techniques used for the numerical stability. The subsequent computed control angles for the maneuvering flight regions compared well with test data. Further, the enhancement of the rotor inflow computations in the inverse simulation through implementation of a Lagrangian wake model improved the convergence of the coupling methodology.

Joint symbolic dynamics for the assessment of cardiovascular and cardiorespiratory interactions

PubMed Central

Baumert, Mathias; Javorka, Michal; Kabir, Muammar

2015-01-01

Beat-to-beat variations in heart period provide information on cardiovascular control and are closely linked to variations in arterial pressure and respiration. Joint symbolic analysis of heart period, systolic arterial pressure and respiration allows for a simple description of their shared short-term dynamics that are governed by cardiac baroreflex control and cardiorespiratory coupling. In this review, we discuss methodology and research applications. Studies suggest that analysis of joint symbolic dynamics provides a powerful tool for identifying physiological and pathophysiological changes in cardiovascular and cardiorespiratory control. PMID:25548272

Joint symbolic dynamics for the assessment of cardiovascular and cardiorespiratory interactions.

PubMed

Baumert, Mathias; Javorka, Michal; Kabir, Muammar

2015-02-13

Beat-to-beat variations in heart period provide information on cardiovascular control and are closely linked to variations in arterial pressure and respiration. Joint symbolic analysis of heart period, systolic arterial pressure and respiration allows for a simple description of their shared short-term dynamics that are governed by cardiac baroreflex control and cardiorespiratory coupling. In this review, we discuss methodology and research applications. Studies suggest that analysis of joint symbolic dynamics provides a powerful tool for identifying physiological and pathophysiological changes in cardiovascular and cardiorespiratory control.

M.G. Velarde: Succint Biography. Doing Science in Spain as a Maverick

NASA Astrophysics Data System (ADS)

Ryazantsev, Yu. S.

A succint account is presented about the professional career of Prof. Manuel García Velarde. Different periods illustrate his engagement with science, education and (domestic and international) organizational endeavor. The chapter also oversees some of the major areas of research he has covered with significant scientific achievements. They embrace kinetic theory, statistical mechanics, thermodynamics, fluid physics, geophysics, optics and lasers, ferromagnetism, electron transport theory, acoustics, elasticity, wave theory, reaction-diffusion science, biophysics, active lattice dynamics, and neuro-dynamics, all phenomena and methodologies treated from the unifying perspective of nonlinear dynamics.

A review of gear housing dynamics and acoustics literature

NASA Technical Reports Server (NTRS)

Lim, Teik Chin; Singh, Rajendra

1989-01-01

A review of the available literature on gear housing vibration and noise radiation is presented. Analytical and experimental methodologies used for bearing dynamics, housing vibration and noise, mounts and suspensions, and the overall gear and housing system are discussed. Typical design guidelines, as outlined by various investigators, are also included. Results of this review indicate that although many attempts were made to characterize the dynamics of gearbox system components, no comprehensive set of design criteria currently exist. Moreover, the literature contains conflicting reports concerning relevant design guidelines.

Philosophy for the rest of cognitive science.

PubMed

Stepp, Nigel; Chemero, Anthony; Turvey, Michael T

2011-04-01

Cognitive science has always included multiple methodologies and theoretical commitments. The philosophy of cognitive science should embrace, or at least acknowledge, this diversity. Bechtel's (2009a) proposed philosophy of cognitive science, however, applies only to representationalist and mechanist cognitive science, ignoring the substantial minority of dynamically oriented cognitive scientists. As an example of nonrepresentational, dynamical cognitive science, we describe strong anticipation as a model for circadian systems (Stepp & Turvey, 2009). We then propose a philosophy of science appropriate to nonrepresentational, dynamical cognitive science. Copyright © 2011 Cognitive Science Society, Inc.

Creating executable architectures using Visual Simulation Objects (VSO)

NASA Astrophysics Data System (ADS)

Woodring, John W.; Comiskey, John B.; Petrov, Orlin M.; Woodring, Brian L.

2005-05-01

Investigations have been performed to identify a methodology for creating executable models of architectures and simulations of architecture that lead to an understanding of their dynamic properties. Colored Petri Nets (CPNs) are used to describe architecture because of their strong mathematical foundations, the existence of techniques for their verification and graph theory"s well-established history of success in modern science. CPNs have been extended to interoperate with legacy simulations via a High Level Architecture (HLA) compliant interface. It has also been demonstrated that an architecture created as a CPN can be integrated with Department of Defense Architecture Framework products to ensure consistency between static and dynamic descriptions. A computer-aided tool, Visual Simulation Objects (VSO), which aids analysts in specifying, composing and executing architectures, has been developed to verify the methodology and as a prototype commercial product.

Criticality Characteristics of Current Oil Price Dynamics

NASA Astrophysics Data System (ADS)

Drożdż, S.; Kwapień, J.; Oświęcimka, P.

2008-10-01

Methodology that recently leads us to predict to an amazing accuracy the date (July 11, 2008) of reverse of the oil price up trend is briefly summarized and some further aspects of the related oil price dynamics elaborated. This methodology is based on the concept of discrete scale invariance whose finance-prediction-oriented variant involves such elements as log-periodic self-similarity, the universal preferred scaling factor λ≈2, and allows a phenomenon of the "super-bubble". From this perspective the present (as of August 22, 2008) violent - but still log-periodically decelerating - decrease of the oil prices is associated with the decay of such a "super-bubble" that has started developing about one year ago on top of the longer-term oil price increasing phase (normal bubble) whose ultimate termination is evaluated to occur in around mid 2010.

Event-Based Tone Mapping for Asynchronous Time-Based Image Sensor

PubMed Central

Simon Chane, Camille; Ieng, Sio-Hoi; Posch, Christoph; Benosman, Ryad B.

2016-01-01

The asynchronous time-based neuromorphic image sensor ATIS is an array of autonomously operating pixels able to encode luminance information with an exceptionally high dynamic range (>143 dB). This paper introduces an event-based methodology to display data from this type of event-based imagers, taking into account the large dynamic range and high temporal accuracy that go beyond available mainstream display technologies. We introduce an event-based tone mapping methodology for asynchronously acquired time encoded gray-level data. A global and a local tone mapping operator are proposed. Both are designed to operate on a stream of incoming events rather than on time frame windows. Experimental results on real outdoor scenes are presented to evaluate the performance of the tone mapping operators in terms of quality, temporal stability, adaptation capability, and computational time. PMID:27642275

Nonlinear dynamic analysis of flexible multibody systems

NASA Technical Reports Server (NTRS)

Bauchau, Olivier A.; Kang, Nam Kook

1991-01-01

Two approaches are developed to analyze the dynamic behavior of flexible multibody systems. In the first approach each body is modeled with a modal methodology in a local non-inertial frame of reference, whereas in the second approach, each body is modeled with a finite element methodology in the inertial frame. In both cases, the interaction among the various elastic bodies is represented by constraint equations. The two approaches were compared for accuracy and efficiency: the first approach is preferable when the nonlinearities are not too strong but it becomes cumbersome and expensive to use when many modes must be used. The second approach is more general and easier to implement but could result in high computation costs for a large system. The constraints should be enforced in a time derivative fashion for better accuracy and stability.

Chocolate Milk with Chia Oil: Ideal Sweetness, Sweeteners Equivalence, and Dynamic Sensory Evaluation Using a Time-Intensity Methodology.

PubMed

Rodrigues, J B; Paixão, J A; Cruz, A G; Bolini, H M A

2015-12-01

The ideal sucrose concentration and equivalent concentrations of the stevia, sucralose, aspartame, and neotame in chocolate milk with chia oil as well as the dynamic behavior of certain sensory attributes were investigated using a time-intensity methodology. The use of just-about-right (JAR) identified an ideal sucrose concentration of 9% (w/w). In addition, the magnitude estimation method showed that stevia had the lowest sweetness power whereas neotame presented the highest. Furthermore, the time-intensity analysis indicated that there was no significant change between the maximum intensities of the sweetness for any evaluated sweeteners. In general, the desired sensory profile and some economic considerations are decisive on the choice of which sweetener is better to be used in chocolate milk formulation added with chia oil. © 2015 Institute of Food Technologists®

Causality analysis in business performance measurement system using system dynamics methodology

NASA Astrophysics Data System (ADS)

Yusof, Zainuridah; Yusoff, Wan Fadzilah Wan; Maarof, Faridah

2014-07-01

One of the main components of the Balanced Scorecard (BSC) that differentiates it from any other performance measurement system (PMS) is the Strategy Map with its unidirectional causality feature. Despite its apparent popularity, criticisms on the causality have been rigorously discussed by earlier researchers. In seeking empirical evidence of causality, propositions based on the service profit chain theory were developed and tested using the econometrics analysis, Granger causality test on the 45 data points. However, the insufficiency of well-established causality models was found as only 40% of the causal linkages were supported by the data. Expert knowledge was suggested to be used in the situations of insufficiency of historical data. The Delphi method was selected and conducted in obtaining the consensus of the causality existence among the 15 selected expert persons by utilizing 3 rounds of questionnaires. Study revealed that only 20% of the propositions were not supported. The existences of bidirectional causality which demonstrate significant dynamic environmental complexity through interaction among measures were obtained from both methods. With that, a computer modeling and simulation using System Dynamics (SD) methodology was develop as an experimental platform to identify how policies impacting the business performance in such environments. The reproduction, sensitivity and extreme condition tests were conducted onto developed SD model to ensure their capability in mimic the reality, robustness and validity for causality analysis platform. This study applied a theoretical service management model within the BSC domain to a practical situation using SD methodology where very limited work has been done.

Test Methodology Development for Experimental Structural Assessment of ASC Planar Spring Material for Long-Term Durability

NASA Technical Reports Server (NTRS)

Yun, Gunjin; Abdullah, A. B. M.; Binienda, Wieslaw; Krause, David L.; Kalluri, Sreeramesh

2014-01-01

A vibration-based testing methodology has been developed that will assess fatigue behavior of the metallic material of construction for the Advanced Stirling Convertor displacer (planar) spring component. To minimize the testing duration, the test setup is designed for base-excitation of a multiplespecimen arrangement, driven in a high-frequency resonant mode; this allows completion of fatigue testing in an accelerated period. A high performance electro-dynamic exciter (shaker) is used to generate harmonic oscillation of cantilever beam specimens, which are clasped on the shaker armature with specially-designed clamp fixtures. The shaker operates in closed-loop control with dynamic specimen response feedback provided by a scanning laser vibrometer. A test coordinator function synchronizes the shaker controller and the laser vibrometer to complete the closed-loop scheme. The test coordinator also monitors structural health of the test specimens throughout the test period, recognizing any change in specimen dynamic behavior. As this may be due to fatigue crack initiation, the test coordinator terminates test progression and then acquires test data in an orderly manner. Design of the specimen and fixture geometry was completed by finite element analysis such that peak stress does not occur at the clamping fixture attachment points. Experimental stress evaluation was conducted to verify the specimen stress predictions. A successful application of the experimental methodology was demonstrated by validation tests with carbon steel specimens subjected to fully-reversed bending stress; high-cycle fatigue failures were induced in such specimens using higher-than-prototypical stresses

4D Subject-Specific Inverse Modeling of the Chick Embryonic Heart Outflow Tract Hemodynamics

PubMed Central

Goenezen, Sevan; Chivukula, Venkat Keshav; Midgett, Madeline; Phan, Ly; Rugonyi, Sandra

2015-01-01

Blood flow plays a critical role in regulating embryonic cardiac growth and development, with altered flow leading to congenital heart disease. Progress in the field, however, is hindered by a lack of quantification of hemodynamic conditions in the developing heart. In this study, we present a methodology to quantify blood flow dynamics in the embryonic heart using subject-specific computational fluid dynamics (CFD) models. While the methodology is general, we focused on a model of the chick embryonic heart outflow tract (OFT), which distally connects the heart to the arterial system, and is the region of origin of many congenital cardiac defects. Using structural and Doppler velocity data collected from optical coherence tomography (OCT), we generated 4D (3D + time) embryo-specific CFD models of the heart OFT. To replicate the blood flow dynamics over time during the cardiac cycle, we developed an iterative inverse-method optimization algorithm, which determines the CFD model boundary conditions such that differences between computed velocities and measured velocities at one point within the OFT lumen are minimized. Results from our developed CFD model agree with previously measured hemodynamics in the OFT. Further, computed velocities and measured velocities differ by less than 15% at locations that were not used in the optimization, validating the model. The presented methodology can be used in quantifications of embryonic cardiac hemodynamics under normal and altered blood flow conditions, enabling an in depth quantitative study of how blood flow influences cardiac development. PMID:26361767

Methodology for dynamic biaxial tension testing of pregnant uterine tissue.

PubMed

Manoogian, Sarah; Mcnally, Craig; Calloway, Britt; Duma, Stefan

2007-01-01

Placental abruption accounts for 50% to 70% of fetal losses in motor vehicle crashes. Since automobile crashes are the leading cause of traumatic fetal injury mortality in the United States, research of this injury mechanism is important. Before research can adequately evaluate current and future restraint designs, a detailed model of the pregnant uterine tissues is necessary. The purpose of this study is to develop a methodology for testing the pregnant uterus in biaxial tension at a rate normally seen in a motor vehicle crash. Since the majority of previous biaxial work has established methods for quasi-static testing, this paper combines previous research and new methods to develop a custom designed system to strain the tissue at a dynamic rate. Load cells and optical markers are used for calculating stress strain curves of the perpendicular loading axes. Results for this methodology show images of a tissue specimen loaded and a finite verification of the optical strain measurement. The biaxial test system dynamically pulls the tissue to failure with synchronous motion of four tissue grips that are rigidly coupled to the tissue specimen. The test device models in situ loading conditions of the pregnant uterus and overcomes previous limitations of biaxial testing. A non-contact method of measuring strains combined with data reduction to resolve the stresses in two directions provides the information necessary to develop a three dimensional constitutive model of the material. Moreover, future research can apply this method to other soft tissues with similar in situ loading conditions.

A program for the investigation of the Multibody Modeling, Verification, and Control Laboratory

NASA Technical Reports Server (NTRS)

Tobbe, Patrick A.; Christian, Paul M.; Rakoczy, John M.; Bulter, Marlon L.

1993-01-01

The Multibody Modeling, Verification, and Control (MMVC) Laboratory is under development at NASA MSFC in Huntsville, Alabama. The laboratory will provide a facility in which dynamic tests and analyses of multibody flexible structures representative of future space systems can be conducted. The purpose of the tests are to acquire dynamic measurements of the flexible structures undergoing large angle motions and use the data to validate the multibody modeling code, TREETOPS, developed under sponsorship of NASA. Advanced control systems design and system identification methodologies will also be implemented in the MMVC laboratory. This paper describes the ground test facility, the real-time control system, and the experiments. A top-level description of the TREETOPS code is also included along with the validation plan for the MMVC program. Dynamic test results from component testing are also presented and discussed. A detailed discussion of the test articles, which manifest the properties of large flexible space structures, is included along with a discussion of the various candidate control methodologies to be applied in the laboratory.

Intelligent approach to prognostic enhancements of diagnostic systems

NASA Astrophysics Data System (ADS)

Vachtsevanos, George; Wang, Peng; Khiripet, Noppadon; Thakker, Ash; Galie, Thomas R.

2001-07-01

This paper introduces a novel methodology to prognostics based on a dynamic wavelet neural network construct and notions from the virtual sensor area. This research has been motivated and supported by the U.S. Navy's active interest in integrating advanced diagnostic and prognostic algorithms in existing Naval digital control and monitoring systems. A rudimentary diagnostic platform is assumed to be available providing timely information about incipient or impending failure conditions. We focus on the development of a prognostic algorithm capable of predicting accurately and reliably the remaining useful lifetime of a failing machine or component. The prognostic module consists of a virtual sensor and a dynamic wavelet neural network as the predictor. The virtual sensor employs process data to map real measurements into difficult to monitor fault quantities. The prognosticator uses a dynamic wavelet neural network as a nonlinear predictor. Means to manage uncertainty and performance metrics are suggested for comparison purposes. An interface to an available shipboard Integrated Condition Assessment System is described and applications to shipboard equipment are discussed. Typical results from pump failures are presented to illustrate the effectiveness of the methodology.

Mechanistic modelling of the inhibitory effect of pH on microbial growth.

PubMed

Akkermans, Simen; Van Impe, Jan F

2018-06-01

Modelling and simulation of microbial dynamics as a function of processing, transportation and storage conditions is a useful tool to improve microbial food safety and quality. The goal of this research is to improve an existing methodology for building mechanistic predictive models based on the environmental conditions. The effect of environmental conditions on microbial dynamics is often described by combining the separate effects in a multiplicative way (gamma concept). This idea was extended further in this work by including the effects of the lag and stationary growth phases on microbial growth rate as independent gamma factors. A mechanistic description of the stationary phase as a function of pH was included, based on a novel class of models that consider product inhibition. Experimental results on Escherichia coli growth dynamics indicated that also the parameters of the product inhibition equations can be modelled with the gamma approach. This work has extended a modelling methodology, resulting in predictive models that are (i) mechanistically inspired, (ii) easily identifiable with a limited work load and (iii) easily extended to additional environmental conditions. Copyright © 2017. Published by Elsevier Ltd.

Robust Adaptive Flight Control Design of Air-breathing Hypersonic Vehicles

DTIC Science & Technology

2016-12-07

dynamic inversion controller design for a non -minimum phase hypersonic vehicle is derived by Kuipers et al. [2008]. Moreover, integrated guidance and...stabilization time for inner loop variables is lesser than the intermediate loop variables because of the three-loop-control design methodology . The control...adaptive design . Control Engineering Practice, 2016. Michael A Bolender and David B Doman. A non -linear model for the longitudinal dynamics of a

Identification of asteroid dynamical families

NASA Technical Reports Server (NTRS)

Valsecchi, G. B.; Carusi, A.; Knezevic, Z.; Kresak, L.; Williams, J. G.

1989-01-01

Problems involved in the identification of asteroid dynamical families are discussed, and some methodological guidelines are presented. Asteroid family classifications are reviewed, and differences in the existing classifications are examined with special attention given to the effects of observational selection on the classification of family membership. The paper also discusses various theories of secular perturbations, including the classical linear theory, the theory of Williams (1969), and the higher order/degree theory of Yuasa (1973).

Evolution of Ada technology in the flight dynamics area: Implementation/testing phase analysis

NASA Technical Reports Server (NTRS)

Quimby, Kelvin L.; Esker, Linda; Miller, John; Smith, Laurie; Stark, Mike; Mcgarry, Frank

1989-01-01

An analysis is presented of the software engineering issues related to the use of Ada for the implementation and system testing phases of four Ada projects developed in the flight dynamics area. These projects reflect an evolving understanding of more effective use of Ada features. In addition, the testing methodology used on these projects has changed substantially from that used on previous FORTRAN projects.

Something in the Way We Move: Motion Dynamics, Not Perceived Sex, Influence Head Movements in Conversation

ERIC Educational Resources Information Center

Boker, Steven M.; Cohn, Jeffrey F.; Theobald, Barry-John; Matthews, Iain; Mangini, Michael; Spies, Jeffrey R.; Ambadar, Zara; Brick, Timothy R.

2011-01-01

During conversation, women tend to nod their heads more frequently and more vigorously than men. An individual speaking with a woman tends to nod his or her head more than when speaking with a man. Is this due to social expectation or due to coupled motion dynamics between the speakers? We present a novel methodology that allows us to randomly…

Ligand diffusion in proteins via enhanced sampling in molecular dynamics.

PubMed

Rydzewski, J; Nowak, W

2017-12-01

Computational simulations in biophysics describe the dynamics and functions of biological macromolecules at the atomic level. Among motions particularly important for life are the transport processes in heterogeneous media. The process of ligand diffusion inside proteins is an example of a complex rare event that can be modeled using molecular dynamics simulations. The study of physical interactions between a ligand and its biological target is of paramount importance for the design of novel drugs and enzymes. Unfortunately, the process of ligand diffusion is difficult to study experimentally. The need for identifying the ligand egress pathways and understanding how ligands migrate through protein tunnels has spurred the development of several methodological approaches to this problem. The complex topology of protein channels and the transient nature of the ligand passage pose difficulties in the modeling of the ligand entry/escape pathways by canonical molecular dynamics simulations. In this review, we report a methodology involving a reconstruction of the ligand diffusion reaction coordinates and the free-energy profiles along these reaction coordinates using enhanced sampling of conformational space. We illustrate the above methods on several ligand-protein systems, including cytochromes and G-protein-coupled receptors. The methods are general and may be adopted to other transport processes in living matter. Copyright © 2017 Elsevier B.V. All rights reserved.

How to assess the impact of a physical parameterization in simulations of moist convection?

NASA Astrophysics Data System (ADS)

Grabowski, Wojciech

2017-04-01

A numerical model capable in simulating moist convection (e.g., cloud-resolving model or large-eddy simulation model) consists of a fluid flow solver combined with required representations (i.e., parameterizations) of physical processes. The later typically include cloud microphysics, radiative transfer, and unresolved turbulent transport. Traditional approaches to investigate impacts of such parameterizations on convective dynamics involve parallel simulations with different parameterization schemes or with different scheme parameters. Such methodologies are not reliable because of the natural variability of a cloud field that is affected by the feedback between the physics and dynamics. For instance, changing the cloud microphysics typically leads to a different realization of the cloud-scale flow, and separating dynamical and microphysical impacts is difficult. This presentation will present a novel modeling methodology, the piggybacking, that allows studying the impact of a physical parameterization on cloud dynamics with confidence. The focus will be on the impact of cloud microphysics parameterization. Specific examples of the piggybacking approach will include simulations concerning the hypothesized deep convection invigoration in polluted environments, the validity of the saturation adjustment in modeling condensation in moist convection, and separation of physical impacts from statistical uncertainty in simulations applying particle-based Lagrangian microphysics, the super-droplet method.

Multiphysics Analysis of a Solid-Core Nuclear Thermal Engine Thrust Chamber

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Canabal, Francisco; Cheng, Gary; Chen, Yen-Sen

2006-01-01

The objective of this effort is to develop an efficient and accurate thermo-fluid computational methodology to predict environments for a hypothetical solid-core, nuclear thermal engine thrust chamber. The computational methodology is based on an unstructured-grid, pressure-based computational fluid dynamics methodology. Formulations for heat transfer in solids and porous media were implemented and anchored. A two-pronged approach was employed in this effort: A detailed thermo-fluid analysis on a multi-channel flow element for mid-section corrosion investigation; and a global modeling of the thrust chamber to understand the effect of hydrogen dissociation and recombination on heat transfer and thrust performance. The formulations and preliminary results on both aspects are presented.

Constraint Force Equation Methodology for Modeling Multi-Body Stage Separation Dynamics

NASA Technical Reports Server (NTRS)

Toniolo, Matthew D.; Tartabini, Paul V.; Pamadi, Bandu N.; Hotchko, Nathaniel

2008-01-01

This paper discusses a generalized approach to the multi-body separation problems in a launch vehicle staging environment based on constraint force methodology and its implementation into the Program to Optimize Simulated Trajectories II (POST2), a widely used trajectory design and optimization tool. This development facilitates the inclusion of stage separation analysis into POST2 for seamless end-to-end simulations of launch vehicle trajectories, thus simplifying the overall implementation and providing a range of modeling and optimization capabilities that are standard features in POST2. Analysis and results are presented for two test cases that validate the constraint force equation methodology in a stand-alone mode and its implementation in POST2.

Descriptive Summaries of the Research Development Test & Evaluation. Army Appropriation FY 1984. Supporting Data FY 1984 Budget Estimate Submitted to Congress--February 1983. Volume I.

DTIC Science & Technology

1983-02-01

s.,ccesstully modeled to enhance future computer design simulations; (2) a new methodology for conduc*n dynamic analysis of vehicle mechanics was...to prelminary design methodology for tilt rotors, advancing blade concepts configuration helicopters, and compound helicopters in conjunction with...feasibility of low-level personnel parachutes has been demon- strated. A study was begun to design a free-fall water contalner. An experimental program to

Computational fluid dynamics combustion analysis evaluation

NASA Technical Reports Server (NTRS)

Kim, Y. M.; Shang, H. M.; Chen, C. P.; Ziebarth, J. P.

1992-01-01

This study involves the development of numerical modelling in spray combustion. These modelling efforts are mainly motivated to improve the computational efficiency in the stochastic particle tracking method as well as to incorporate the physical submodels of turbulence, combustion, vaporization, and dense spray effects. The present mathematical formulation and numerical methodologies can be casted in any time-marching pressure correction methodologies (PCM) such as FDNS code and MAST code. A sequence of validation cases involving steady burning sprays and transient evaporating sprays will be included.

Optimal Trajectories Generation in Robotic Fiber Placement Systems

NASA Astrophysics Data System (ADS)

Gao, Jiuchun; Pashkevich, Anatol; Caro, Stéphane

2017-06-01

The paper proposes a methodology for optimal trajectories generation in robotic fiber placement systems. A strategy to tune the parameters of the optimization algorithm at hand is also introduced. The presented technique transforms the original continuous problem into a discrete one where the time-optimal motions are generated by using dynamic programming. The developed strategy for the optimization algorithm tuning allows essentially reducing the computing time and obtaining trajectories satisfying industrial constraints. Feasibilities and advantages of the proposed methodology are confirmed by an application example.

Enhanced Learning Methodologies and the Implementation of an Identification Course

NASA Astrophysics Data System (ADS)

Guidorzi, Roberto

This paper proposes some considerations on the role played by information and communication technologies in the evolution of educational systems and describes the design philosophy and the realization of a basic course on dynamic system identification that relies on constructivist methodologies and on the use of e-learning environments. It reports also some of the opinions formulated by the students on the effectiveness of the available tools and on their role in acquiring proficiency in the application of identification techniques in modeling real processes.

Naval Ship Maintenance: An Analysis of the Dutch Shipbuilding Industry using the Knowledge Value Added, Systems Dynamics, and Integrated Risk Management Methodologies

DTIC Science & Technology

2013-04-01

and Integrated Risk Management Methodologies 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e...supply chains, risk management with real options, and sustainability . [dnford@nps.edu] Thomas J. Housel—Housel specializes in valuing intellectual...maintenance services for the RDN. Damen Schelde has used an ILS since 2002 to manage the shipbuilding process from project initiation through the

A Method for Co-Designing Theory-Based Behaviour Change Systems for Health Promotion.

PubMed

Janols, Rebecka; Lindgren, Helena

2017-01-01

A methodology was defined and developed for designing theory-based behaviour change systems for health promotion that can be tailored to the individual. Theories from two research fields were combined with a participatory action research methodology. Two case studies applying the methodology were conducted. During and between group sessions the participants created material and designs following the behaviour change strategy themes, which were discussed, analysed and transformed into a design of a behaviour change system. Theories in behavioural change and persuasive technology guided the data collection, data analyses, and the design of a behaviour change system. The methodology has strong emphasis on the target group's participation in the design process. The different aspects brought forward related to behaviour change strategies defined in literature on persuasive technology, and the dynamics of these are associated to needs and motivation defined in literature on behaviour change. It was concluded that the methodology aids the integration of theories into a participatory action research design process, and aids the analyses and motivations of design choices.

Simulation modeling of route guidance concept

DOT National Transportation Integrated Search

1997-01-01

The methodology of a simulation model developed at the University of New South Wales, Australia, for the evaluation of performance of Dynamic Route Guidance Systems (DRGS) is described. The microscopic simulation model adopts the event update simulat...

Real-time dynamic pricing for bicycle sharing programs.

DOT National Transportation Integrated Search

2014-10-01

This paper presents a new conceptual approach to improve the operational performance of public bike sharing systems : using pricing schemes. Its methodological developments are accompanied by experimental analyses with bike demand : data from Capital...

Dynamic travel time estimation using regression trees.

DOT National Transportation Integrated Search

2008-10-01

This report presents a methodology for travel time estimation by using regression trees. The dissemination of travel time information has become crucial for effective traffic management, especially under congested road conditions. In the absence of c...

Ninth NASTRAN (R) Users' Colloquium

NASA Technical Reports Server (NTRS)

1980-01-01

The general application of finite element methodology and the specific application of NASTRAN to a wide variety of static and dynamic structural problems is addressed. Comparison with other approaches and new methods of analysis with nastran are included.

Data-Driven Modeling of Complex Systems by means of a Dynamical ANN

NASA Astrophysics Data System (ADS)

Seleznev, A.; Mukhin, D.; Gavrilov, A.; Loskutov, E.; Feigin, A.

2017-12-01

The data-driven methods for modeling and prognosis of complex dynamical systems become more and more popular in various fields due to growth of high-resolution data. We distinguish the two basic steps in such an approach: (i) determining the phase subspace of the system, or embedding, from available time series and (ii) constructing an evolution operator acting in this reduced subspace. In this work we suggest a novel approach combining these two steps by means of construction of an artificial neural network (ANN) with special topology. The proposed ANN-based model, on the one hand, projects the data onto a low-dimensional manifold, and, on the other hand, models a dynamical system on this manifold. Actually, this is a recurrent multilayer ANN which has internal dynamics and capable of generating time series. Very important point of the proposed methodology is the optimization of the model allowing us to avoid overfitting: we use Bayesian criterion to optimize the ANN structure and estimate both the degree of evolution operator nonlinearity and the complexity of nonlinear manifold which the data are projected on. The proposed modeling technique will be applied to the analysis of high-dimensional dynamical systems: Lorenz'96 model of atmospheric turbulence, producing high-dimensional space-time chaos, and quasi-geostrophic three-layer model of the Earth's atmosphere with the natural orography, describing the dynamics of synoptical vortexes as well as mesoscale blocking systems. The possibility of application of the proposed methodology to analyze real measured data is also discussed. The study was supported by the Russian Science Foundation (grant #16-12-10198).

A methodology for the efficient integration of transient constraints in the design of aircraft dynamic systems

NASA Astrophysics Data System (ADS)

Phan, Leon L.

The motivation behind this thesis mainly stems from previous work performed at Hispano-Suiza (Safran Group) in the context of the European research project "Power Optimised Aircraft". Extensive testing on the COPPER Bird RTM, a test rig designed to characterize aircraft electrical networks, demonstrated the relevance of transient regimes in the design and development of dynamic systems. Transient regimes experienced by dynamic systems may have severe impacts on the operation of the aircraft. For example, the switching on of a high electrical load might cause a network voltage drop inducing a loss of power available to critical aircraft systems. These transient behaviors are thus often regulated by dynamic constraints, requiring the dynamic signals to remain within bounds whose values vary with time. The verification of these peculiar types of constraints, which generally requires high-fidelity time-domain simulation, intervenes late in the system development process, thus potentially causing costly design iterations. The research objective of this thesis is to develop a methodology that integrates the verification of dynamic constraints in the early specification of dynamic systems. In order to circumvent the inefficiencies of time-domain simulation, multivariate dynamic surrogate models of the original time-domain simulation models are generated, building on a nonlinear system identification technique using wavelet neural networks (or wavenets), which allow the multiscale nature of transient signals to be captured. However, training multivariate wavenets can become computationally prohibitive as the number of design variables increases. Therefore, an alternate approach is formulated, in which dynamic surrogate models using sigmoid-based neural networks are used to emulate the transient behavior of the envelopes of the time-domain response. Thus, in order to train the neural network, the envelopes are extracted by first separating the scales of the dynamic response, using a multiresolution analysis (MRA) based on the discrete wavelet transform. The MRA separates the dynamic response into a trend and a noise signal (ripple). The envelope of the noise is then computed with a windowing method, and recombined with the trend in order to reconstruct the global envelope of the dynamic response. The run-time efficiency of the resulting dynamic surrogate models enable the implementation of a data farming approach, in which a Monte-Carlo simulation generates time-domain behaviors of transient responses for a vast set of design and operation scenarios spanning the design and operation space. An interactive visualization environment, enabling what-if analyses, will be developed; the user can thereby instantaneously comprehend the transient response of the system (or its envelope) and its sensitivities to design and operation variables, as well as filter the design space to have it exhibit only the design scenarios verifying the dynamic constraints. The proposed methodology, along with its foundational hypotheses, are tested on the design and optimization of a 350VDC network, where a generator and its control system are concurrently designed in order to minimize the electrical losses, while ensuring that the transient undervoltage induced by peak demands in the consumption of a motor does not violate transient power quality constraints.

Discrete Abstractions of Hybrid Systems: Verification of Safety and Application to User-Interface Design

NASA Technical Reports Server (NTRS)

Oishi, Meeko; Tomlin, Claire; Degani, Asaf

2003-01-01

Human interaction with complex hybrid systems involves the user, the automation's discrete mode logic, and the underlying continuous dynamics of the physical system. Often the user-interface of such systems displays a reduced set of information about the entire system. In safety-critical systems, how can we identify user-interface designs which do not have adequate information, or which may confuse the user? Here we describe a methodology, based on hybrid system analysis, to verify that a user-interface contains information necessary to safely complete a desired procedure or task. Verification within a hybrid framework allows us to account for the continuous dynamics underlying the simple, discrete representations displayed to the user. We provide two examples: a car traveling through a yellow light at an intersection and an aircraft autopilot in a landing/go-around maneuver. The examples demonstrate the general nature of this methodology, which is applicable to hybrid systems (not fully automated) which have operational constraints we can pose in terms of safety. This methodology differs from existing work in hybrid system verification in that we directly account for the user's interactions with the system.

Evaluation of Structural Robustness against Column Loss: Methodology and Application to RC Frame Buildings.

PubMed

Bao, Yihai; Main, Joseph A; Noh, Sam-Young

2017-08-01

A computational methodology is presented for evaluating structural robustness against column loss. The methodology is illustrated through application to reinforced concrete (RC) frame buildings, using a reduced-order modeling approach for three-dimensional RC framing systems that includes the floor slabs. Comparisons with high-fidelity finite-element model results are presented to verify the approach. Pushdown analyses of prototype buildings under column loss scenarios are performed using the reduced-order modeling approach, and an energy-based procedure is employed to account for the dynamic effects associated with sudden column loss. Results obtained using the energy-based approach are found to be in good agreement with results from direct dynamic analysis of sudden column loss. A metric for structural robustness is proposed, calculated by normalizing the ultimate capacities of the structural system under sudden column loss by the applicable service-level gravity loading and by evaluating the minimum value of this normalized ultimate capacity over all column removal scenarios. The procedure is applied to two prototype 10-story RC buildings, one employing intermediate moment frames (IMFs) and the other employing special moment frames (SMFs). The SMF building, with its more stringent seismic design and detailing, is found to have greater robustness.

Multiple templates-based homology modeling enhances structure quality of AT1 receptor: validation by molecular dynamics and antagonist docking.

PubMed

Sokkar, Pandian; Mohandass, Shylajanaciyar; Ramachandran, Murugesan

2011-07-01

We present a comparative account on 3D-structures of human type-1 receptor (AT1) for angiotensin II (AngII), modeled using three different methodologies. AngII activates a wide spectrum of signaling responses via the AT1 receptor that mediates physiological control of blood pressure and diverse pathological actions in cardiovascular, renal, and other cell types. Availability of 3D-model of AT1 receptor would significantly enhance the development of new drugs for cardiovascular diseases. However, templates of AT1 receptor with low sequence similarity increase the complexity in straightforward homology modeling, and hence there is a need to evaluate different modeling methodologies in order to use the models for sensitive applications such as rational drug design. Three models were generated for AT1 receptor by, (1) homology modeling with bovine rhodopsin as template, (2) homology modeling with multiple templates and (3) threading using I-TASSER web server. Molecular dynamics (MD) simulation (15 ns) of models in explicit membrane-water system, Ramachandran plot analysis and molecular docking with antagonists led to the conclusion that multiple template-based homology modeling outweighs other methodologies for AT1 modeling.

Validations of Coupled CSD/CFD and Particle Vortex Transport Method for Rotorcraft Applications: Hover, Transition, and High Speed Flights

NASA Technical Reports Server (NTRS)

Anusonti-Inthra, Phuriwat

2010-01-01

This paper presents validations of a novel rotorcraft analysis that coupled Computational Fluid Dynamics (CFD), Computational Structural Dynamics (CSD), and Particle Vortex Transport Method (PVTM) methodologies. The CSD with associated vehicle trim analysis is used to calculate blade deformations and trim parameters. The near body CFD analysis is employed to provide detailed near body flow field information which is used to obtain high-fidelity blade aerodynamic loadings. The far field wake dominated region is simulated using the PVTM analysis which provides accurate prediction of the evolution of the rotor wake released from the near body CFD domains. A loose coupling methodology between the CSD and CFD/PVTM modules are used with appropriate information exchange amongst the CSD/CFD/PVTM modules. The coupled CSD/CFD/PVTM methodology is used to simulate various rotorcraft flight conditions (i.e. hover, transition, and high speed flights), and the results are compared with several sets of experimental data. For the hover condition, the results are compared with hover data for the HART II rotor tested at DLR Institute of Flight Systems, Germany. For the forward flight conditions, the results are validated with the UH-60A flight test data.

Socio-Hydrology: Conceptual and Methodological Challenges in the Bidirectional Coupling of Human and Water Systems

NASA Astrophysics Data System (ADS)

Scott, C. A.

2014-12-01

This presentation reviews conceptual advances in the emerging field of socio-hydrology that focuses on coupled human and water systems. An important current challenge is how to better couple the bidirectional influences between human and water systems, which lead to emergent dynamics. The interactions among (1) the structure and dynamics of systems with (2) human values and norms lead to (3) outcomes, which in turn influence subsequent interactions. Human influences on hydrological systems are relatively well understood, chiefly resulting from developments in the field of water resources. The ecosystem-service concept of cultural value has expanded understanding of decision-making beyond economic rationality criteria. Hydrological impacts on social processes are less well developed conceptually, but this is changing with growing attention to vulnerability, adaptation, and resilience, particularly in the face of climate change. Methodological limitations, especially in characterizing the range of human responses to hydrological events and drivers, still pose challenges to modeling bidirectional human-water influences. Evidence from multiple case studies, synthesized in more broadly generic syndromes, helps surmount these methodological limitations and offers the potential to improve characterization and quantification of socio-hydrological systems.

Time-resolved Analysis of Proteome Dynamics by Tandem Mass Tags and Stable Isotope Labeling in Cell Culture (TMT-SILAC) Hyperplexing*

PubMed Central

Welle, Kevin A.; Zhang, Tian; Hryhorenko, Jennifer R.; Shen, Shichen; Qu, Jun; Ghaemmaghami, Sina

2016-01-01

Recent advances in mass spectrometry have enabled system-wide analyses of protein turnover. By globally quantifying the kinetics of protein clearance and synthesis, these methodologies can provide important insights into the regulation of the proteome under varying cellular and environmental conditions. To facilitate such analyses, we have employed a methodology that combines metabolic isotopic labeling (Stable Isotope Labeling in Cell Culture - SILAC) with isobaric tagging (Tandem Mass Tags - TMT) for analysis of multiplexed samples. The fractional labeling of multiple time-points can be measured in a single mass spectrometry run, providing temporally resolved measurements of protein turnover kinetics. To demonstrate the feasibility of the approach, we simultaneously measured the kinetics of protein clearance and accumulation for more than 3000 proteins in dividing and quiescent human fibroblasts and verified the accuracy of the measurements by comparison to established non-multiplexed approaches. The results indicate that upon reaching quiescence, fibroblasts compensate for lack of cellular growth by globally downregulating protein synthesis and upregulating protein degradation. The described methodology significantly reduces the cost and complexity of temporally-resolved dynamic proteomic experiments and improves the precision of proteome-wide turnover data. PMID:27765818

Hybrid CMS methods with model reduction for assembly of structures

NASA Technical Reports Server (NTRS)

Farhat, Charbel

1991-01-01

Future on-orbit structures will be designed and built in several stages, each with specific control requirements. Therefore there must be a methodology which can predict the dynamic characteristics of the assembled structure, based on the dynamic characteristics of the subassemblies and their interfaces. The methodology developed by CSC to address this issue is Hybrid Component Mode Synthesis (HCMS). HCMS distinguishes itself from standard component mode synthesis algorithms in the following features: (1) it does not require the subcomponents to have displacement compatible models, which makes it ideal for analyzing the deployment of heterogeneous flexible multibody systems, (2) it incorporates a second-level model reduction scheme at the interface, which makes it much faster than other algorithms and therefore suitable for control purposes, and (3) it does answer specific questions such as 'how does the global fundamental frequency vary if I change the physical parameters of substructure k by a specified amount?'. Because it is based on an energy principle rather than displacement compatibility, this methodology can also help the designer to define an assembly process. Current and future efforts are devoted to applying the HCMS method to design and analyze docking and berthing procedures in orbital construction.

Preloading To Accelerate Slow-Crack-Growth Testing

NASA Technical Reports Server (NTRS)

Gyekenyesi, John P.; Choi, Sung R.; Pawlik, Ralph J.

2004-01-01

An accelerated-testing methodology has been developed for measuring the slow-crack-growth (SCG) behavior of brittle materials. Like the prior methodology, the accelerated-testing methodology involves dynamic fatigue ( constant stress-rate) testing, in which a load or a displacement is applied to a specimen at a constant rate. SCG parameters or life prediction parameters needed for designing components made of the same material as that of the specimen are calculated from the relationship between (1) the strength of the material as measured in the test and (2) the applied stress rate used in the test. Despite its simplicity and convenience, dynamic fatigue testing as practiced heretofore has one major drawback: it is extremely time-consuming, especially at low stress rates. The present accelerated methodology reduces the time needed to test a specimen at a given rate of applied load, stress, or displacement. Instead of starting the test from zero applied load or displacement as in the prior methodology, one preloads the specimen and increases the applied load at the specified rate (see Figure 1). One might expect the preload to alter the results of the test and indeed it does, but fortunately, it is possible to account for the effect of the preload in interpreting the results. The accounting is done by calculating the normalized strength (defined as the strength in the presence of preload the strength in the absence of preload) as a function of (1) the preloading factor (defined as the preload stress the strength in the absence of preload) and (2) a SCG parameter, denoted n, that is used in a power-law crack-speed formulation. Figure 2 presents numerical results from this theoretical calculation.

A proven approach for more effective software development and maintenance

NASA Technical Reports Server (NTRS)

Pajerski, Rose; Hall, Dana; Sinclair, Craig

1994-01-01

Modern space flight mission operations and associated ground data systems are increasingly dependent upon reliable, quality software. Critical functions such as command load preparation, health and status monitoring, communications link scheduling and conflict resolution, and transparent gateway protocol conversion are routinely performed by software. Given budget constraints and the ever increasing capabilities of processor technology, the next generation of control centers and data systems will be even more dependent upon software across all aspects of performance. A key challenge now is to implement improved engineering, management, and assurance processes for the development and maintenance of that software; processes that cost less, yield higher quality products, and that self-correct for continual improvement evolution. The NASA Goddard Space Flight Center has a unique experience base that can be readily tapped to help solve the software challenge. Over the past eighteen years, the Software Engineering Laboratory within the code 500 Flight Dynamics Division has evolved a software development and maintenance methodology that accommodates the unique characteristics of an organization while optimizing and continually improving the organization's software capabilities. This methodology relies upon measurement, analysis, and feedback much analogous to that of control loop systems. It is an approach with a time-tested track record proven through repeated applications across a broad range of operational software development and maintenance projects. This paper describes the software improvement methodology employed by the Software Engineering Laboratory, and how it has been exploited within the Flight Dynamics Division with GSFC Code 500. Examples of specific improvement in the software itself and its processes are presented to illustrate the effectiveness of the methodology. Finally, the initial findings are given when this methodology was applied across the mission operations and ground data systems software domains throughout Code 500.

Development of Multi-physics (Multiphase CFD + MCNP) simulation for generic solution vessel power calculation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Seung Jun; Buechler, Cynthia Eileen

The current study aims to predict the steady state power of a generic solution vessel and to develop a corresponding heat transfer coefficient correlation for a Moly99 production facility by conducting a fully coupled multi-physics simulation. A prediction of steady state power for the current application is inherently interconnected between thermal hydraulic characteristics (i.e. Multiphase computational fluid dynamics solved by ANSYS-Fluent 17.2) and the corresponding neutronic behavior (i.e. particle transport solved by MCNP6.2) in the solution vessel. Thus, the development of a coupling methodology is vital to understand the system behavior at a variety of system design and postulated operatingmore » scenarios. In this study, we report on the k-effective (keff) calculation for the baseline solution vessel configuration with a selected solution concentration using MCNP K-code modeling. The associated correlation of thermal properties (e.g. density, viscosity, thermal conductivity, specific heat) at the selected solution concentration are developed based on existing experimental measurements in the open literature. The numerical coupling methodology between multiphase CFD and MCNP is successfully demonstrated, and the detailed coupling procedure is documented. In addition, improved coupling methods capturing realistic physics in the solution vessel thermal-neutronic dynamics are proposed and tested further (i.e. dynamic height adjustment, mull-cell approach). As a key outcome of the current study, a multi-physics coupling methodology between MCFD and MCNP is demonstrated and tested for four different operating conditions. Those different operating conditions are determined based on the neutron source strength at a fixed geometry condition. The steady state powers for the generic solution vessel at various operating conditions are reported, and a generalized correlation of the heat transfer coefficient for the current application is discussed. The assessment of multi-physics methodology and preliminary results from various coupled calculations (power prediction and heat transfer coefficient) can be further utilized for the system code validation and generic solution vessel design improvement.« less

Hybrid analysis for indicating patients with breast cancer using temperature time series.

PubMed

Silva, Lincoln F; Santos, Alair Augusto S M D; Bravo, Renato S; Silva, Aristófanes C; Muchaluat-Saade, Débora C; Conci, Aura

2016-07-01

Breast cancer is the most common cancer among women worldwide. Diagnosis and treatment in early stages increase cure chances. The temperature of cancerous tissue is generally higher than that of healthy surrounding tissues, making thermography an option to be considered in screening strategies of this cancer type. This paper proposes a hybrid methodology for analyzing dynamic infrared thermography in order to indicate patients with risk of breast cancer, using unsupervised and supervised machine learning techniques, which characterizes the methodology as hybrid. The dynamic infrared thermography monitors or quantitatively measures temperature changes on the examined surface, after a thermal stress. In the dynamic infrared thermography execution, a sequence of breast thermograms is generated. In the proposed methodology, this sequence is processed and analyzed by several techniques. First, the region of the breasts is segmented and the thermograms of the sequence are registered. Then, temperature time series are built and the k-means algorithm is applied on these series using various values of k. Clustering formed by k-means algorithm, for each k value, is evaluated using clustering validation indices, generating values treated as features in the classification model construction step. A data mining tool was used to solve the combined algorithm selection and hyperparameter optimization (CASH) problem in classification tasks. Besides the classification algorithm recommended by the data mining tool, classifiers based on Bayesian networks, neural networks, decision rules and decision tree were executed on the data set used for evaluation. Test results support that the proposed analysis methodology is able to indicate patients with breast cancer. Among 39 tested classification algorithms, K-Star and Bayes Net presented 100% classification accuracy. Furthermore, among the Bayes Net, multi-layer perceptron, decision table and random forest classification algorithms, an average accuracy of 95.38% was obtained. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Multiscale simulations of anisotropic particles combining molecular dynamics and Green's function reaction dynamics

NASA Astrophysics Data System (ADS)

Vijaykumar, Adithya; Ouldridge, Thomas E.; ten Wolde, Pieter Rein; Bolhuis, Peter G.

2017-03-01

The modeling of complex reaction-diffusion processes in, for instance, cellular biochemical networks or self-assembling soft matter can be tremendously sped up by employing a multiscale algorithm which combines the mesoscopic Green's Function Reaction Dynamics (GFRD) method with explicit stochastic Brownian, Langevin, or deterministic molecular dynamics to treat reactants at the microscopic scale [A. Vijaykumar, P. G. Bolhuis, and P. R. ten Wolde, J. Chem. Phys. 143, 214102 (2015)]. Here we extend this multiscale MD-GFRD approach to include the orientational dynamics that is crucial to describe the anisotropic interactions often prevalent in biomolecular systems. We present the novel algorithm focusing on Brownian dynamics only, although the methodology is generic. We illustrate the novel algorithm using a simple patchy particle model. After validation of the algorithm, we discuss its performance. The rotational Brownian dynamics MD-GFRD multiscale method will open up the possibility for large scale simulations of protein signalling networks.

Chattering-Free Sliding Mode Control with Unmodeled Dynamics

NASA Technical Reports Server (NTRS)

Krupp, Don; Shtessel, Yuri B.

1999-01-01

Sliding mode control systems are valued for their robust accommodation of uncertainties and their ability to reject disturbances. In this paper, a design methodology is proposed to eliminate the chattering phenomenon affecting sliding mode controlled plants with input unmodeled actuator dynamics of second order or greater. The proposed controller design is based on the relative degrees of the plant and the unmodeled actuator dynamics and the ranges of the uncertainties of the plant and actuator. The controller utilizes the pass filter characteristics of the physical actuating device to provide a smoothing effect on the discontinuous control signal rather than introducing any artificial dynamics into the controller design thus eliminating chattering in the system's output response.

Application of design sensitivity analysis for greater improvement on machine structural dynamics

NASA Technical Reports Server (NTRS)

Yoshimura, Masataka

1987-01-01

Methodologies are presented for greatly improving machine structural dynamics by using design sensitivity analyses and evaluative parameters. First, design sensitivity coefficients and evaluative parameters of structural dynamics are described. Next, the relations between the design sensitivity coefficients and the evaluative parameters are clarified. Then, design improvement procedures of structural dynamics are proposed for the following three cases: (1) addition of elastic structural members, (2) addition of mass elements, and (3) substantial charges of joint design variables. Cases (1) and (2) correspond to the changes of the initial framework or configuration, and (3) corresponds to the alteration of poor initial design variables. Finally, numerical examples are given for demonstrating the availability of the methods proposed.

Inferring Instantaneous, Multivariate and Nonlinear Sensitivities for the Analysis of Feedback Processes in a Dynamical System: Lorenz Model Case Study

NASA Technical Reports Server (NTRS)

Aires, Filipe; Rossow, William B.; Hansen, James E. (Technical Monitor)

2001-01-01

A new approach is presented for the analysis of feedback processes in a nonlinear dynamical system by observing its variations. The new methodology consists of statistical estimates of the sensitivities between all pairs of variables in the system based on a neural network modeling of the dynamical system. The model can then be used to estimate the instantaneous, multivariate and nonlinear sensitivities, which are shown to be essential for the analysis of the feedbacks processes involved in the dynamical system. The method is described and tested on synthetic data from the low-order Lorenz circulation model where the correct sensitivities can be evaluated analytically.

Integral control for population management.

PubMed

Guiver, Chris; Logemann, Hartmut; Rebarber, Richard; Bill, Adam; Tenhumberg, Brigitte; Hodgson, Dave; Townley, Stuart

2015-04-01

We present a novel management methodology for restocking a declining population. The strategy uses integral control, a concept ubiquitous in control theory which has not been applied to population dynamics. Integral control is based on dynamic feedback-using measurements of the population to inform management strategies and is robust to model uncertainty, an important consideration for ecological models. We demonstrate from first principles why such an approach to population management is suitable via theory and examples.

Experimental and Computational Studies of Molecular and Lattice Symmetries of Energetic Materials at High Pressure

DTIC Science & Technology

2002-01-01

Prescribed by ANSI Std Z39-18 Research and Technology Department Dynamics and Diagnostics Division, Static High- Pressure Group Overall Research...Department Dynamics and Diagnostics Division, Static High- Pressure Group Impact of this Basic Research • This research generates phase and density...Static High- Pressure Group Experimental Methodology Use Diamond Anvil Cells (DAC) with coil Heaters (HDAC) to achieve • High pressures (P) to 10 GPa

Interactive Macroeconomics

NASA Astrophysics Data System (ADS)

Di Guilmi, Corrado; Gallegati, Mauro; Landini, Simone

2017-04-01

Preface; List of tables; List of figures, 1. Introduction; Part I. Methodological Notes and Tools: 2. The state space notion; 3. The master equation; Part II. Applications to HIA Based Models: 4. Financial fragility and macroeconomic dynamics I: heterogeneity and interaction; 5. Financial fragility and macroeconomic Dynamics II: learning; Part III. Conclusions: 6. Conclusive remarks; Part IV. Appendices and Complements: Appendix A: Complements to Chapter 3; Appendix B: Solving the ME to solve the ABM; Appendix C: Specifying transition rates; Index.

Transport in Dynamical Astronomy and Multibody Problems

NASA Astrophysics Data System (ADS)

Dellnitz, Michael; Junge, Oliver; Koon, Wang Sang; Lekien, Francois; Lo, Martin W.; Marsden, Jerrold E.; Padberg, Kathrin; Preis, Robert; Ross, Shane D.; Thiere, Bianca

We combine the techniques of almost invariant sets (using tree structured box elimination and graph partitioning algorithms) with invariant manifold and lobe dynamics techniques. The result is a new computational technique for computing key dynamical features, including almost invariant sets, resonance regions as well as transport rates and bottlenecks between regions in dynamical systems. This methodology can be applied to a variety of multibody problems, including those in molecular modeling, chemical reaction rates and dynamical astronomy. In this paper we focus on problems in dynamical astronomy to illustrate the power of the combination of these different numerical tools and their applicability. In particular, we compute transport rates between two resonance regions for the three-body system consisting of the Sun, Jupiter and a third body (such as an asteroid). These resonance regions are appropriate for certain comets and asteroids.

Dynamic Stochastic Control of Freeway Corridor Systems : Summary and Project Overview

DOT National Transportation Integrated Search

1978-12-01

Systematic methodological approaches to overall traffic management from both short-term (real-time) and long-term (planning) perspectives have been developed. The approach embodies formulation and solution of interrelated mathematical problems from o...

Analytical Electrochemistry: Methodology and Applications of Dynamic Techniques.

ERIC Educational Resources Information Center

Heineman, William R.; Kissinger, Peter T.

1980-01-01

Reports developments involving the experimental aspects of finite and current analytical electrochemistry including electrode materials (97 cited references), hydrodynamic techniques (56), spectroelectrochemistry (62), stripping voltammetry (70), voltammetric techniques (27), polarographic techniques (59), and miscellany (12). (CS)

Rail Passenger Vehicle Truck Design Methodology

DOT National Transportation Integrated Search

1981-01-01

A procedure for the selection of rail passenger truck design parameters to meet dynamic performance indices has been developed. The procedure is based upon partitioning the design task into three tradeoff studies: (1) a vertical ride quality-secondar...

Calculation of surface potentials at the silica–water interface using molecular dynamics: Challenges and opportunities

NASA Astrophysics Data System (ADS)

Lowe, Benjamin M.; Skylaris, Chris-Kriton; Green, Nicolas G.; Shibuta, Yasushi; Sakata, Toshiya

2018-04-01

Continuum-based methods are important in calculating electrostatic properties of interfacial systems such as the electric field and surface potential but are incapable of providing sufficient insight into a range of fundamentally and technologically important phenomena which occur at atomistic length-scales. In this work a molecular dynamics methodology is presented for interfacial electric field and potential calculations. The silica–water interface was chosen as an example system, which is highly relevant for understanding the response of field-effect transistors sensors (FET sensors). Detailed validation work is presented, followed by the simulated surface charge/surface potential relationship. This showed good agreement with experiment at low surface charge density but at high surface charge density the results highlighted challenges presented by an atomistic definition of the surface potential. This methodology will be used to investigate the effect of surface morphology and biomolecule addition; both factors which are challenging using conventional continuum models.

The instrumental genesis process in future primary teachers using Dynamic Geometry Software

NASA Astrophysics Data System (ADS)

Ruiz-López, Natalia

2018-05-01

This paper, which describes a study undertaken with pairs of future primary teachers using GeoGebra software to solve geometry problems, includes a brief literature review, the theoretical framework and methodology used. An analysis of the instrumental genesis process for a pair participating in the case study is also provided. This analysis addresses the techniques and types of dragging used, the obstacles to learning encountered, a description of the interaction between the pair and their interaction with the teacher, and the type of language used. Based on this analysis, possibilities and limitations of the instrumental genesis process are identified for the development of geometric competencies such as conjecture creation, property checking and problem researching. It is also suggested that the methodology used in the analysis of the problem solving process may be useful for those teachers and researchers who want to integrate Dynamic Geometry Software (DGS) in their classrooms.

Preliminary Results from a Model-Driven Architecture Methodology for Development of an Event-Driven Space Communications Service Concept

NASA Technical Reports Server (NTRS)

Roberts, Christopher J.; Morgenstern, Robert M.; Israel, David J.; Borky, John M.; Bradley, Thomas H.

2017-01-01

NASA's next generation space communications network will involve dynamic and autonomous services analogous to services provided by current terrestrial wireless networks. This architecture concept, known as the Space Mobile Network (SMN), is enabled by several technologies now in development. A pillar of the SMN architecture is the establishment and utilization of a continuous bidirectional control plane space link channel and a new User Initiated Service (UIS) protocol to enable more dynamic and autonomous mission operations concepts, reduced user space communications planning burden, and more efficient and effective provider network resource utilization. This paper provides preliminary results from the application of model driven architecture methodology to develop UIS. Such an approach is necessary to ensure systematic investigation of several open questions concerning the efficiency, robustness, interoperability, scalability and security of the control plane space link and UIS protocol.

Study on a new chaotic bitwise dynamical system and its FPGA implementation

NASA Astrophysics Data System (ADS)

Wang, Qian-Xue; Yu, Si-Min; Guyeux, C.; Bahi, J.; Fang, Xiao-Le

2015-06-01

In this paper, the structure of a new chaotic bitwise dynamical system (CBDS) is described. Compared to our previous research work, it uses various random bitwise operations instead of only one. The chaotic behavior of CBDS is mathematically proven according to the Devaney's definition, and its statistical properties are verified both for uniformity and by a comprehensive, reputed and stringent battery of tests called TestU01. Furthermore, a systematic methodology developing the parallel computations is proposed for FPGA platform-based realization of this CBDS. Experiments finally validate the proposed systematic methodology. Project supported by China Postdoctoral Science Foundation (Grant No. 2014M552175), the Scientific Research Foundation for the Returned Overseas Chinese Scholars, Chinese Education Ministry, the National Natural Science Foundation of China (Grant No. 61172023), and the Specialized Research Foundation of Doctoral Subjects of Chinese Education Ministry (Grant No. 20114420110003).

Transition Characteristic Analysis of Traffic Evolution Process for Urban Traffic Network

PubMed Central

Chen, Hong; Li, Yang

2014-01-01

The characterization of the dynamics of traffic states remains fundamental to seeking for the solutions of diverse traffic problems. To gain more insights into traffic dynamics in the temporal domain, this paper explored temporal characteristics and distinct regularity in the traffic evolution process of urban traffic network. We defined traffic state pattern through clustering multidimensional traffic time series using self-organizing maps and construct a pattern transition network model that is appropriate for representing and analyzing the evolution progress. The methodology is illustrated by an application to data flow rate of multiple road sections from Network of Shenzhen's Nanshan District, China. Analysis and numerical results demonstrated that the methodology permits extracting many useful traffic transition characteristics including stability, preference, activity, and attractiveness. In addition, more information about the relationships between these characteristics was extracted, which should be helpful in understanding the complex behavior of the temporal evolution features of traffic patterns. PMID:24982969

CFD Aided Design and Production of Hydraulic Turbines

NASA Astrophysics Data System (ADS)

Kaplan, Alper; Cetinturk, Huseyin; Demirel, Gizem; Ayli, Ece; Celebioglu, Kutay; Aradag, Selin; ETU Hydro Research Center Team

2014-11-01

Hydraulic turbines are turbo machines which produce electricity from hydraulic energy. Francis type turbines are the most common one in use today. The design of these turbines requires high engineering effort since each turbine is tailor made due to different head and discharge. Therefore each component of the turbine is designed specifically. During the last decades, Computational Fluid Dynamics (CFD) has become very useful tool to predict hydraulic machinery performance and save time and money for designers. This paper describes a design methodology to optimize a Francis turbine by integrating theoretical and experimental fundamentals of hydraulic machines and commercial CFD codes. Specific turbines are designed and manufactured with the help of a collaborative CFD/CAD/CAM methodology based on computational fluid dynamics and five-axis machining for hydraulic electric power plants. The details are presented in this study. This study is financially supported by Turkish Ministry of Development.

Geometry and Dynamics for Markov Chain Monte Carlo

NASA Astrophysics Data System (ADS)

Barp, Alessandro; Briol, François-Xavier; Kennedy, Anthony D.; Girolami, Mark

2018-03-01

Markov Chain Monte Carlo methods have revolutionised mathematical computation and enabled statistical inference within many previously intractable models. In this context, Hamiltonian dynamics have been proposed as an efficient way of building chains which can explore probability densities efficiently. The method emerges from physics and geometry and these links have been extensively studied by a series of authors through the last thirty years. However, there is currently a gap between the intuitions and knowledge of users of the methodology and our deep understanding of these theoretical foundations. The aim of this review is to provide a comprehensive introduction to the geometric tools used in Hamiltonian Monte Carlo at a level accessible to statisticians, machine learners and other users of the methodology with only a basic understanding of Monte Carlo methods. This will be complemented with some discussion of the most recent advances in the field which we believe will become increasingly relevant to applied scientists.

Coordinated Dynamic Behaviors for Multirobot Systems With Collision Avoidance.

PubMed

Sabattini, Lorenzo; Secchi, Cristian; Fantuzzi, Cesare

2017-12-01

In this paper, we propose a novel methodology for achieving complex dynamic behaviors in multirobot systems. In particular, we consider a multirobot system partitioned into two subgroups: 1) dependent and 2) independent robots. Independent robots are utilized as a control input, and their motion is controlled in such a way that the dependent robots solve a tracking problem, that is following arbitrarily defined setpoint trajectories, in a coordinated manner. The control strategy proposed in this paper explicitly addresses the collision avoidance problem, utilizing a null space-based behavioral approach: this leads to combining, in a non conflicting manner, the tracking control law with a collision avoidance strategy. The combination of these control actions allows the robots to execute their task in a safe way. Avoidance of collisions is formally proven in this paper, and the proposed methodology is validated by means of simulations and experiments on real robots.

Learning a trajectory using adjoint functions and teacher forcing

NASA Technical Reports Server (NTRS)

Toomarian, Nikzad B.; Barhen, Jacob

1992-01-01

A new methodology for faster supervised temporal learning in nonlinear neural networks is presented which builds upon the concept of adjoint operators to allow fast computation of the gradients of an error functional with respect to all parameters of the neural architecture, and exploits the concept of teacher forcing to incorporate information on the desired output into the activation dynamics. The importance of the initial or final time conditions for the adjoint equations is discussed. A new algorithm is presented in which the adjoint equations are solved simultaneously (i.e., forward in time) with the activation dynamics of the neural network. We also indicate how teacher forcing can be modulated in time as learning proceeds. The results obtained show that the learning time is reduced by one to two orders of magnitude with respect to previously published results, while trajectory tracking is significantly improved. The proposed methodology makes hardware implementation of temporal learning attractive for real-time applications.

MM/PBSA analysis of molecular dynamics simulations of bovine beta-lactoglobulin: free energy gradients in conformational transitions?

PubMed

Fogolari, Federico; Moroni, Elisabetta; Wojciechowski, Marcin; Baginski, Maciej; Ragona, Laura; Molinari, Henriette

2005-04-01

The pH-driven opening and closure of beta-lactoglobulin EF loop, acting as a lid and closing the internal cavity of the protein, has been studied by molecular dynamics (MD) simulations and free energy calculations based on molecular mechanics/Poisson-Boltzmann (PB) solvent-accessible surface area (MM/PBSA) methodology. The forms above and below the transition pH differ presumably only in the protonation state of residue Glu89. MM/PBSA calculations are able to reproduce qualitatively the thermodynamics of the transition. The analysis of MD simulations using a combination of MM/PBSA methodology and the colony energy approach is able to highlight the driving forces implied in the transition. The analysis suggests that global rearrangements take place before the equilibrium local conformation is reached. This conclusion may bear general relevance to conformational transitions in all lipocalins and proteins in general. (c) 2005 Wiley-Liss, Inc.

Measuring individual differences in responses to date-rape vignettes using latent variable models.

PubMed

Tuliao, Antover P; Hoffman, Lesa; McChargue, Dennis E

2017-01-01

Vignette methodology can be a flexible and powerful way to examine individual differences in response to dangerous real-life scenarios. However, most studies underutilize the usefulness of such methodology by analyzing only one outcome, which limits the ability to track event-related changes (e.g., vacillation in risk perception). The current study was designed to illustrate the dynamic influence of risk perception on exit point from a date-rape vignette. Our primary goal was to provide an illustrative example of how to use latent variable models for vignette methodology, including latent growth curve modeling with piecewise slopes, as well as latent variable measurement models. Through the combination of a step-by-step exposition in this text and corresponding model syntax available electronically, we detail an alternative statistical "blueprint" to enhance future violence research efforts using vignette methodology. Aggr. Behav. 43:60-73, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Methodology for Computational Fluid Dynamic Validation for Medical Use: Application to Intracranial Aneurysm.

PubMed

Paliwal, Nikhil; Damiano, Robert J; Varble, Nicole A; Tutino, Vincent M; Dou, Zhongwang; Siddiqui, Adnan H; Meng, Hui

2017-12-01

Computational fluid dynamics (CFD) is a promising tool to aid in clinical diagnoses of cardiovascular diseases. However, it uses assumptions that simplify the complexities of the real cardiovascular flow. Due to high-stakes in the clinical setting, it is critical to calculate the effect of these assumptions in the CFD simulation results. However, existing CFD validation approaches do not quantify error in the simulation results due to the CFD solver's modeling assumptions. Instead, they directly compare CFD simulation results against validation data. Thus, to quantify the accuracy of a CFD solver, we developed a validation methodology that calculates the CFD model error (arising from modeling assumptions). Our methodology identifies independent error sources in CFD and validation experiments, and calculates the model error by parsing out other sources of error inherent in simulation and experiments. To demonstrate the method, we simulated the flow field of a patient-specific intracranial aneurysm (IA) in the commercial CFD software star-ccm+. Particle image velocimetry (PIV) provided validation datasets for the flow field on two orthogonal planes. The average model error in the star-ccm+ solver was 5.63 ± 5.49% along the intersecting validation line of the orthogonal planes. Furthermore, we demonstrated that our validation method is superior to existing validation approaches by applying three representative existing validation techniques to our CFD and experimental dataset, and comparing the validation results. Our validation methodology offers a streamlined workflow to extract the "true" accuracy of a CFD solver.

Predictor-Based Model Reference Adaptive Control

NASA Technical Reports Server (NTRS)

Lavretsky, Eugene; Gadient, Ross; Gregory, Irene M.

2009-01-01

This paper is devoted to robust, Predictor-based Model Reference Adaptive Control (PMRAC) design. The proposed adaptive system is compared with the now-classical Model Reference Adaptive Control (MRAC) architecture. Simulation examples are presented. Numerical evidence indicates that the proposed PMRAC tracking architecture has better than MRAC transient characteristics. In this paper, we presented a state-predictor based direct adaptive tracking design methodology for multi-input dynamical systems, with partially known dynamics. Efficiency of the design was demonstrated using short period dynamics of an aircraft. Formal proof of the reported PMRAC benefits constitute future research and will be reported elsewhere.

Commentary 2: Sibling Power Dynamics: The Role of Family and Sociocultural Context.

PubMed

Updegraff, Kimberly A

2017-06-01

The balance of power and control is an understudied, yet important, aspect of the sibling relationship that is theorized to shift over the course of development from early childhood to young adulthood. The investigations in this issue offer support for this overall progression, but extend prior research by providing a nuanced understanding of sibling power dynamics using different methodologies, analytic approaches, and study designs. Grounded within an ecological framework, directions for future research are offered to expand our understanding of sibling power dynamics in diverse family and sociocultural contexts. © 2017 Wiley Periodicals, Inc.

A self-learning algorithm for biased molecular dynamics

PubMed Central

Tribello, Gareth A.; Ceriotti, Michele; Parrinello, Michele

2010-01-01

A new self-learning algorithm for accelerated dynamics, reconnaissance metadynamics, is proposed that is able to work with a very large number of collective coordinates. Acceleration of the dynamics is achieved by constructing a bias potential in terms of a patchwork of one-dimensional, locally valid collective coordinates. These collective coordinates are obtained from trajectory analyses so that they adapt to any new features encountered during the simulation. We show how this methodology can be used to enhance sampling in real chemical systems citing examples both from the physics of clusters and from the biological sciences. PMID:20876135

Analysis of Bioprocesses. Dynamic Modeling is a Must.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramkrishna, Doraiswami; Song, Hyun-Seob

2016-01-01

The goal of this paper is to report on the performance of a promising dynamic framework based on the cybernetic concepts which have evolved over three decades. We present case studies of successful dynamic simulations of wild-type strains as well as specific KO mutants on bacteria and yeast. An extensive metabolic engineering effort, including genome scale networks, is called for to secure the methodology and realize its full potential. Towards this end, the software AUMIC is under active further development to enable speedy applications. Its wide use will be enabled by a publication that is shortly due.

Understanding the kinetics of ligand binding to globins with molecular dynamics simulations: the necessity of multiple state models.

PubMed

Estarellas Martin, Carolina; Seira Castan, Constantí; Luque Garriga, F Javier; Bidon-Chanal Badia, Axel

2015-10-01

Residue conformational changes and internal cavity migration processes play a key role in regulating the kinetics of ligand migration and binding events in globins. Molecular dynamics simulations have demonstrated their value in the study of these processes in different haemoglobins, but derivation of kinetic data demands the use of more complex techniques like enhanced sampling molecular dynamics methods. This review discusses the different methodologies that are currently applied to study the ligand migration process in globins and highlight those specially developed to derive kinetic data. Copyright © 2015 Elsevier Ltd. All rights reserved.

Guidelines for Computing Longitudinal Dynamic Stability Characteristics of a Subsonic Transport

NASA Technical Reports Server (NTRS)

Thompson, Joseph R.; Frank, Neal T.; Murphy, Patrick C.

2010-01-01

A systematic study is presented to guide the selection of a numerical solution strategy for URANS computation of a subsonic transport configuration undergoing simulated forced oscillation about its pitch axis. Forced oscillation is central to the prevalent wind tunnel methodology for quantifying aircraft dynamic stability derivatives from force and moment coefficients, which is the ultimate goal for the computational simulations. Extensive computations are performed that lead in key insights of the critical numerical parameters affecting solution convergence. A preliminary linear harmonic analysis is included to demonstrate the potential of extracting dynamic stability derivatives from computational solutions.

Accurate Sloshing Modes Modeling: A New Analytical Solution and its Consequences on Control

NASA Astrophysics Data System (ADS)

Gonidou, Luc-Olivier; Desmariaux, Jean

2014-06-01

This study addresses the issue of sloshing modes modeling for GNC analyses purposes. On European launchers, equivalent mechanical systems are commonly used for modeling sloshing effects on launcher dynamics. The representativeness of such a methodology is discussed here. First an exact analytical formulation of the launcher dynamics fitted with sloshing modes is proposed and discrepancies with equivalent mechanical system approach are emphasized. Then preliminary comparative GNC analyses are performed using the different models of dynamics in order to evaluate the impact of the aforementioned discrepancies from GNC standpoint. Special attention is paid to system stability.

Robust control synthesis for uncertain dynamical systems

NASA Technical Reports Server (NTRS)

Byun, Kuk-Whan; Wie, Bong; Sunkel, John

1989-01-01

This paper presents robust control synthesis techniques for uncertain dynamical systems subject to structured parameter perturbation. Both QFT (quantitative feedback theory) and H-infinity control synthesis techniques are investigated. Although most H-infinity-related control techniques are not concerned with the structured parameter perturbation, a new way of incorporating the parameter uncertainty in the robust H-infinity control design is presented. A generic model of uncertain dynamical systems is used to illustrate the design methodologies investigated in this paper. It is shown that, for a certain noncolocated structural control problem, use of both techniques results in nonminimum phase compensation.

gr-MRI: A software package for magnetic resonance imaging using software defined radios.

PubMed

Hasselwander, Christopher J; Cao, Zhipeng; Grissom, William A

2016-09-01

The goal of this work is to develop software that enables the rapid implementation of custom MRI spectrometers using commercially-available software defined radios (SDRs). The developed gr-MRI software package comprises a set of Python scripts, flowgraphs, and signal generation and recording blocks for GNU Radio, an open-source SDR software package that is widely used in communications research. gr-MRI implements basic event sequencing functionality, and tools for system calibrations, multi-radio synchronization, and MR signal processing and image reconstruction. It includes four pulse sequences: a single-pulse sequence to record free induction signals, a gradient-recalled echo imaging sequence, a spin echo imaging sequence, and an inversion recovery spin echo imaging sequence. The sequences were used to perform phantom imaging scans with a 0.5Tesla tabletop MRI scanner and two commercially-available SDRs. One SDR was used for RF excitation and reception, and the other for gradient pulse generation. The total SDR hardware cost was approximately $2000. The frequency of radio desynchronization events and the frequency with which the software recovered from those events was also measured, and the SDR's ability to generate frequency-swept RF waveforms was validated and compared to the scanner's commercial spectrometer. The spin echo images geometrically matched those acquired using the commercial spectrometer, with no unexpected distortions. Desynchronization events were more likely to occur at the very beginning of an imaging scan, but were nearly eliminated if the user invoked the sequence for a short period before beginning data recording. The SDR produced a 500kHz bandwidth frequency-swept pulse with high fidelity, while the commercial spectrometer produced a waveform with large frequency spike errors. In conclusion, the developed gr-MRI software can be used to develop high-fidelity, low-cost custom MRI spectrometers using commercially-available SDRs. Copyright © 2016. Published by Elsevier Inc.

Identifying and correcting non-Markov states in peptide conformational dynamics

NASA Astrophysics Data System (ADS)

Nerukh, Dmitry; Jensen, Christian H.; Glen, Robert C.

2010-02-01

Conformational transitions in proteins define their biological activity and can be investigated in detail using the Markov state model. The fundamental assumption on the transitions between the states, their Markov property, is critical in this framework. We test this assumption by analyzing the transitions obtained directly from the dynamics of a molecular dynamics simulated peptide valine-proline-alanine-leucine and states defined phenomenologically using clustering in dihedral space. We find that the transitions are Markovian at the time scale of ≈50 ps and longer. However, at the time scale of 30-40 ps the dynamics loses its Markov property. Our methodology reveals the mechanism that leads to non-Markov behavior. It also provides a way of regrouping the conformations into new states that now possess the required Markov property of their dynamics.

Energy-optimal path planning by stochastic dynamically orthogonal level-set optimization

NASA Astrophysics Data System (ADS)

Subramani, Deepak N.; Lermusiaux, Pierre F. J.

2016-04-01

A stochastic optimization methodology is formulated for computing energy-optimal paths from among time-optimal paths of autonomous vehicles navigating in a dynamic flow field. Based on partial differential equations, the methodology rigorously leverages the level-set equation that governs time-optimal reachability fronts for a given relative vehicle-speed function. To set up the energy optimization, the relative vehicle-speed and headings are considered to be stochastic and new stochastic Dynamically Orthogonal (DO) level-set equations are derived. Their solution provides the distribution of time-optimal reachability fronts and corresponding distribution of time-optimal paths. An optimization is then performed on the vehicle's energy-time joint distribution to select the energy-optimal paths for each arrival time, among all stochastic time-optimal paths for that arrival time. Numerical schemes to solve the reduced stochastic DO level-set equations are obtained, and accuracy and efficiency considerations are discussed. These reduced equations are first shown to be efficient at solving the governing stochastic level-sets, in part by comparisons with direct Monte Carlo simulations. To validate the methodology and illustrate its accuracy, comparisons with semi-analytical energy-optimal path solutions are then completed. In particular, we consider the energy-optimal crossing of a canonical steady front and set up its semi-analytical solution using a energy-time nested nonlinear double-optimization scheme. We then showcase the inner workings and nuances of the energy-optimal path planning, considering different mission scenarios. Finally, we study and discuss results of energy-optimal missions in a wind-driven barotropic quasi-geostrophic double-gyre ocean circulation.

Spacecraft alignment estimation. [for onboard sensors

NASA Technical Reports Server (NTRS)

Shuster, Malcolm D.; Bierman, Gerald J.

1988-01-01

A numerically well-behaved factorized methodology is developed for estimating spacecraft sensor alignments from prelaunch and inflight data without the need to compute the spacecraft attitude or angular velocity. Such a methodology permits the estimation of sensor alignments (or other biases) in a framework free of unknown dynamical variables. In actual mission implementation such an algorithm is usually better behaved than one that must compute sensor alignments simultaneously with the spacecraft attitude, for example by means of a Kalman filter. In particular, such a methodology is less sensitive to data dropouts of long duration, and the derived measurement used in the attitude-independent algorithm usually makes data checking and editing of outliers much simpler than would be the case in the filter.

Ambient Vibration Testing for Story Stiffness Estimation of a Heritage Timber Building

PubMed Central

Min, Kyung-Won; Kim, Junhee; Park, Sung-Ah; Park, Chan-Soo

2013-01-01

This paper investigates dynamic characteristics of a historic wooden structure by ambient vibration testing, presenting a novel estimation methodology of story stiffness for the purpose of vibration-based structural health monitoring. As for the ambient vibration testing, measured structural responses are analyzed by two output-only system identification methods (i.e., frequency domain decomposition and stochastic subspace identification) to estimate modal parameters. The proposed methodology of story stiffness is estimation based on an eigenvalue problem derived from a vibratory rigid body model. Using the identified natural frequencies, the eigenvalue problem is efficiently solved and uniquely yields story stiffness. It is noteworthy that application of the proposed methodology is not necessarily confined to the wooden structure exampled in the paper. PMID:24227999

Methodological Innovations for Studying Organizations.

DTIC Science & Technology

1981-01-01

dynamics among artists in the Hollywood film industry . James Dabbs is a Professor of Psychology at Georgia State University. His research interests...development of careers in the Hollywood film industry . Throughout, Faulkner emphasizes the interplay between evidence from archives and documents on

Event-driven management algorithm of an Engineering documents circulation system

NASA Astrophysics Data System (ADS)

Kuzenkov, V.; Zebzeev, A.; Gromakov, E.

2015-04-01

Development methodology of an engineering documents circulation system in the design company is reviewed. Discrete event-driven automatic models using description algorithms of project management is offered. Petri net use for dynamic design of projects is offered.

Data based identification and prediction of nonlinear and complex dynamical systems

NASA Astrophysics Data System (ADS)

Wang, Wen-Xu; Lai, Ying-Cheng; Grebogi, Celso

2016-07-01

The problem of reconstructing nonlinear and complex dynamical systems from measured data or time series is central to many scientific disciplines including physical, biological, computer, and social sciences, as well as engineering and economics. The classic approach to phase-space reconstruction through the methodology of delay-coordinate embedding has been practiced for more than three decades, but the paradigm is effective mostly for low-dimensional dynamical systems. Often, the methodology yields only a topological correspondence of the original system. There are situations in various fields of science and engineering where the systems of interest are complex and high dimensional with many interacting components. A complex system typically exhibits a rich variety of collective dynamics, and it is of great interest to be able to detect, classify, understand, predict, and control the dynamics using data that are becoming increasingly accessible due to the advances of modern information technology. To accomplish these goals, especially prediction and control, an accurate reconstruction of the original system is required. Nonlinear and complex systems identification aims at inferring, from data, the mathematical equations that govern the dynamical evolution and the complex interaction patterns, or topology, among the various components of the system. With successful reconstruction of the system equations and the connecting topology, it may be possible to address challenging and significant problems such as identification of causal relations among the interacting components and detection of hidden nodes. The "inverse" problem thus presents a grand challenge, requiring new paradigms beyond the traditional delay-coordinate embedding methodology. The past fifteen years have witnessed rapid development of contemporary complex graph theory with broad applications in interdisciplinary science and engineering. The combination of graph, information, and nonlinear dynamical systems theories with tools from statistical physics, optimization, engineering control, applied mathematics, and scientific computing enables the development of a number of paradigms to address the problem of nonlinear and complex systems reconstruction. In this Review, we describe the recent advances in this forefront and rapidly evolving field, with a focus on compressive sensing based methods. In particular, compressive sensing is a paradigm developed in recent years in applied mathematics, electrical engineering, and nonlinear physics to reconstruct sparse signals using only limited data. It has broad applications ranging from image compression/reconstruction to the analysis of large-scale sensor networks, and it has become a powerful technique to obtain high-fidelity signals for applications where sufficient observations are not available. We will describe in detail how compressive sensing can be exploited to address a diverse array of problems in data based reconstruction of nonlinear and complex networked systems. The problems include identification of chaotic systems and prediction of catastrophic bifurcations, forecasting future attractors of time-varying nonlinear systems, reconstruction of complex networks with oscillatory and evolutionary game dynamics, detection of hidden nodes, identification of chaotic elements in neuronal networks, reconstruction of complex geospatial networks and nodal positioning, and reconstruction of complex spreading networks with binary data.. A number of alternative methods, such as those based on system response to external driving, synchronization, and noise-induced dynamical correlation, will also be discussed. Due to the high relevance of network reconstruction to biological sciences, a special section is devoted to a brief survey of the current methods to infer biological networks. Finally, a number of open problems including control and controllability of complex nonlinear dynamical networks are discussed. The methods outlined in this Review are principled on various concepts in complexity science and engineering such as phase transitions, bifurcations, stabilities, and robustness. The methodologies have the potential to significantly improve our ability to understand a variety of complex dynamical systems ranging from gene regulatory systems to social networks toward the ultimate goal of controlling such systems.

Effects of land use/cover change and harvests on forest carbon dynamics in northern states of the United States from remote sensing and inventory data: 1992-2001

Treesearch

Daolan Zheng; Linda S. Heath; Mark J. Ducey; James E. Smith

2011-01-01

We examined spatial patterns of changes in forest area and nonsoil carbon (C) dynamics affected by land use/cover change (LUC) and harvests in 24 northern states of the United States using an integrated methodology combining remote sensing and ground inventory data between 1992 and 2001. We used the Retrofit Change Product from the Multi-Resolution Land Characteristics...

Integrated Line-of-Sight Modeling of the Airborne Aero-Optics Laboratory

DTIC Science & Technology

2013-09-01

43rd AIAA Fluid Dynamics Conference and Exhibit, San Diego, 2013 . [4] K. O’ Keefe , "Dynamic Modeling Methodology," in International Conference on...information if it does not display a currently valid OMB control number. 1. REPORT DATE SEP 2013 2. REPORT TYPE 3. DATES COVERED 00-00- 2013 to 00-00- 2013 ...distribution unlimited 13. SUPPLEMENTARY NOTES 2013 AMOS (Advanced Maui Optical and Space Surveillance) Technical Conference, 10-13 Sep, Maui, HI. 14

Review of dynamic optimization methods in renewable natural resource management

USGS Publications Warehouse

Williams, B.K.

1989-01-01

In recent years, the applications of dynamic optimization procedures in natural resource management have proliferated. A systematic review of these applications is given in terms of a number of optimization methodologies and natural resource systems. The applicability of the methods to renewable natural resource systems are compared in terms of system complexity, system size, and precision of the optimal solutions. Recommendations are made concerning the appropriate methods for certain kinds of biological resource problems.

A system dynamics approach to the study of Colombian coca cultivation and the counter-intuitive consequence of law enforcement.

PubMed

Jaén, Sebastian; Dyner, Isaac

2014-03-01

A large-scale expansion of the Colombian coca cultivation is one of the most revealing signs of a structural change in the illegal cocaine market in the Andean region. From being a modest and domestic production, in the space of five years Colombian coca cultivation supplied a competitive market, capable of substituting almost completely the foreign sources of supply. The purpose of this work is to explore the role and potential of system dynamics (SD) as a modeling methodology to better understand the consequences of drug policy. As a case study, this work tests the hypothesis that the outbreak of Colombian coca cultivations is a consequence of the take down of large cartels, leading to the surge of small drug-trafficking firms called "cartelitos." Using an SD model, and elements from the economic theory of the criminal firm, our work shows how the formation of these small firms might significantly contribute to the configuring of a more competitive domestic coca industry (and hence to a more efficient crime industry). We conclude that SD seems an appropriate dynamic modeling-based approach to address policy issues regarding drug markets. The methodology takes into account the dynamic nature of drug markets and their multi-dimensional responses to policy interventions. Copyright © 2014 Elsevier B.V. All rights reserved.

Oceanic residual depth measurements, the plate cooling model, and global dynamic topography

NASA Astrophysics Data System (ADS)

Hoggard, Mark J.; Winterbourne, Jeff; Czarnota, Karol; White, Nicky

2017-03-01

Convective circulation of the mantle causes deflections of the Earth's surface that vary as a function of space and time. Accurate measurements of this dynamic topography are complicated by the need to isolate and remove other sources of elevation, arising from flexure and lithospheric isostasy. The complex architecture of continental lithosphere means that measurement of present-day dynamic topography is more straightforward in the oceanic realm. Here we present an updated methodology for calculating oceanic residual bathymetry, which is a proxy for dynamic topography. Corrections are applied that account for the effects of sedimentary loading and compaction, for anomalous crustal thickness variations, for subsidence of oceanic lithosphere as a function of age and for non-hydrostatic geoid height variations. Errors are formally propagated to estimate measurement uncertainties. We apply this methodology to a global database of 1936 seismic surveys located on oceanic crust and generate 2297 spot measurements of residual topography, including 1161 with crustal corrections. The resultant anomalies have amplitudes of ±1 km and wavelengths of ˜1000 km. Spectral analysis of our database using cross-validation demonstrates that spherical harmonics up to and including degree 30 (i.e., wavelengths down to 1300 km) are required to accurately represent these observations. Truncation of the expansion at a lower maximum degree erroneously increases the amplitude of inferred long-wavelength dynamic topography. There is a strong correlation between our observations and free-air gravity anomalies, magmatism, ridge seismicity, vertical motions of adjacent rifted margins, and global tomographic models. We infer that shorter wavelength components of the observed pattern of dynamic topography may be attributable to the presence of thermal anomalies within the shallow asthenospheric mantle.

Nonlinear Slewing Spacecraft Control Based on Exergy, Power Flow, and Static and Dynamic Stability

NASA Astrophysics Data System (ADS)

Robinett, Rush D.; Wilson, David G.

2009-10-01

This paper presents a new nonlinear control methodology for slewing spacecraft, which provides both necessary and sufficient conditions for stability by identifying the stability boundaries, rigid body modes, and limit cycles. Conservative Hamiltonian system concepts, which are equivalent to static stability of airplanes, are used to find and deal with the static stability boundaries: rigid body modes. The application of exergy and entropy thermodynamic concepts to the work-rate principle provides a natural partitioning through the second law of thermodynamics of power flows into exergy generator, dissipator, and storage for Hamiltonian systems that is employed to find the dynamic stability boundaries: limit cycles. This partitioning process enables the control system designer to directly evaluate and enhance the stability and performance of the system by balancing the power flowing into versus the power dissipated within the system subject to the Hamiltonian surface (power storage). Relationships are developed between exergy, power flow, static and dynamic stability, and Lyapunov analysis. The methodology is demonstrated with two illustrative examples: (1) a nonlinear oscillator with sinusoidal damping and (2) a multi-input-multi-output three-axis slewing spacecraft that employs proportional-integral-derivative tracking control with numerical simulation results.

Nonnormality and Divergence in Posttreatment Alcohol Use

PubMed Central

Witkiewitz, Katie; van der Maas, Han L. J.; Hufford, Michael R.; Marlatt, G. Alan

2007-01-01

Alcohol lapses are the modal outcome following treatment for alcohol use disorders, yet many alcohol researchers have encountered limited success in the prediction and prevention of relapse. One hypothesis is that lapses are unpredictable, but another possibility is the complexity of the relapse process is not captured by traditional statistical methods. Data from Project Matching Alcohol Treatments to Client Heterogeneity (Project MATCH), a multisite alcohol treatment study, were reanalyzed with 2 statistical methodologies: catastrophe and 2-part growth mixture modeling. Drawing on previous investigations of self-efficacy as a dynamic predictor of relapse, the current study revisits the self-efficacy matching hypothesis, which was not statistically supported in Project MATCH. Results from both the catastrophe and growth mixture analyses demonstrated a dynamic relationship between self-efficacy and drinking outcomes. The growth mixture analyses provided evidence in support of the original matching hypothesis: Individuals with lower self-efficacy who received cognitive behavior therapy drank far less frequently than did those with low self-efficacy who received motivational therapy. These results highlight the dynamical nature of the relapse process and the importance of the use of methodologies that accommodate this complexity when evaluating treatment outcomes. PMID:17516769

Medial surface dynamics of the vocal folds in an in vivo canine model

NASA Astrophysics Data System (ADS)

Doellinger, Michael; Berke, Gerald S.; Chhetri, Dinesh K.; Berry, David A.

2004-05-01

Quantitative measurement of the medial surface dynamics of the vocal folds is important for understanding how sound is generated in the larynx. However, such data are hard to gather because of the inaccessibility of the vocal folds. Recent studies have applied hemi-larynx methodology to excised human larynges, to visualize these dynamics. The present study extends this methodology to obtain similar quantitative measurements using an in vivo canine hemi-larynx setup, with varying levels of stimulation to the recurrent laryngeal nerve. Use of an in vivo model allows us to examine effects of intrinsic muscle contraction on the medial surface of the vocal folds, to provide greater insight into mechanisms of vocal control. Data were collected using digital high-speed imaging with a sampling frequency of up to 4000 Hz, and a spatial resolution of up to 1024×1024 pixels. Three-dimensional motion will be extracted, computed, visualized, and contrasted as a function of the level of stimulation to the recurrent laryngeal nerve. Results will also be compared to patterns of vibration in excised larynges. Finally, commonly applied quantitative analyses will be performed to investigate the underlying modes of vibration. [Work supported by NIH/NIDCD.

Long story short: an introduction to the short-term and long-term Six Sigma quality and its importance in the laboratory medicine for the management of extra-analytical processes.

PubMed

Ialongo, Cristiano; Bernardini, Sergio

2018-06-18

There is a compelling need for quality tools that enable effective control of the extra-analytical phase. In this regard, Six Sigma seems to offer a valid methodological and conceptual opportunity, and in recent times, the International Federation of Clinical Chemistry and Laboratory Medicine has adopted it for indicating the performance requirements for non-analytical laboratory processes. However, the Six Sigma implies a distinction between short-term and long-term quality that is based on the dynamics of the processes. These concepts are still not widespread and applied in the field of laboratory medicine although they are of fundamental importance to exploit the full potential of this methodology. This paper reviews the Six Sigma quality concepts and shows how they originated from Shewhart's control charts, in respect of which they are not an alternative but a completion. It also discusses the dynamic nature of process and how it arises, concerning particularly the long-term dynamic mean variation, and explains why this leads to the fundamental distinction of quality we previously mentioned.

Three-dimensional sensing methodology combining stereo vision and phase-measuring profilometry based on dynamic programming

NASA Astrophysics Data System (ADS)

Lee, Hyunki; Kim, Min Young; Moon, Jeon Il

2017-12-01

Phase measuring profilometry and moiré methodology have been widely applied to the three-dimensional shape measurement of target objects, because of their high measuring speed and accuracy. However, these methods suffer from inherent limitations called a correspondence problem, or 2π-ambiguity problem. Although a kind of sensing method to combine well-known stereo vision and phase measuring profilometry (PMP) technique simultaneously has been developed to overcome this problem, it still requires definite improvement for sensing speed and measurement accuracy. We propose a dynamic programming-based stereo PMP method to acquire more reliable depth information and in a relatively small time period. The proposed method efficiently fuses information from two stereo sensors in terms of phase and intensity simultaneously based on a newly defined cost function of dynamic programming. In addition, the important parameters are analyzed at the view point of the 2π-ambiguity problem and measurement accuracy. To analyze the influence of important hardware and software parameters related to the measurement performance and to verify its efficiency, accuracy, and sensing speed, a series of experimental tests were performed with various objects and sensor configurations.

Predicting U.S. food demand in the 20th century: a new look at system dynamics

NASA Astrophysics Data System (ADS)

Moorthy, Mukund; Cellier, Francois E.; LaFrance, Jeffrey T.

1998-08-01

The paper describes a new methodology for predicting the behavior of macroeconomic variables. The approach is based on System Dynamics and Fuzzy Inductive Reasoning. A four- layer pseudo-hierarchical model is proposed. The bottom layer makes predications about population dynamics, age distributions among the populace, as well as demographics. The second layer makes predications about the general state of the economy, including such variables as inflation and unemployment. The third layer makes predictions about the demand for certain goods or services, such as milk products, used cars, mobile telephones, or internet services. The fourth and top layer makes predictions about the supply of such goods and services, both in terms of their prices. Each layer can be influenced by control variables the values of which are only determined at higher levels. In this sense, the model is not strictly hierarchical. For example, the demand for goods at level three depends on the prices of these goods, which are only determined at level four. Yet, the prices are themselves influenced by the expected demand. The methodology is exemplified by means of a macroeconomic model that makes predictions about US food demand during the 20th century.

End-To-End Simulation of Launch Vehicle Trajectories Including Stage Separation Dynamics

NASA Technical Reports Server (NTRS)

Albertson, Cindy W.; Tartabini, Paul V.; Pamadi, Bandu N.

2012-01-01

The development of methodologies, techniques, and tools for analysis and simulation of stage separation dynamics is critically needed for successful design and operation of multistage reusable launch vehicles. As a part of this activity, the Constraint Force Equation (CFE) methodology was developed and implemented in the Program to Optimize Simulated Trajectories II (POST2). The objective of this paper is to demonstrate the capability of POST2/CFE to simulate a complete end-to-end mission. The vehicle configuration selected was the Two-Stage-To-Orbit (TSTO) Langley Glide Back Booster (LGBB) bimese configuration, an in-house concept consisting of a reusable booster and an orbiter having identical outer mold lines. The proximity and isolated aerodynamic databases used for the simulation were assembled using wind-tunnel test data for this vehicle. POST2/CFE simulation results are presented for the entire mission, from lift-off, through stage separation, orbiter ascent to orbit, and booster glide back to the launch site. Additionally, POST2/CFE stage separation simulation results are compared with results from industry standard commercial software used for solving dynamics problems involving multiple bodies connected by joints.

Analysis of discrete and continuous distributions of ventilatory time constants from dynamic computed tomography

NASA Astrophysics Data System (ADS)

Doebrich, Marcus; Markstaller, Klaus; Karmrodt, Jens; Kauczor, Hans-Ulrich; Eberle, Balthasar; Weiler, Norbert; Thelen, Manfred; Schreiber, Wolfgang G.

2005-04-01

In this study, an algorithm was developed to measure the distribution of pulmonary time constants (TCs) from dynamic computed tomography (CT) data sets during a sudden airway pressure step up. Simulations with synthetic data were performed to test the methodology as well as the influence of experimental noise. Furthermore the algorithm was applied to in vivo data. In five pigs sudden changes in airway pressure were imposed during dynamic CT acquisition in healthy lungs and in a saline lavage ARDS model. The fractional gas content in the imaged slice (FGC) was calculated by density measurements for each CT image. Temporal variations of the FGC were analysed assuming a model with a continuous distribution of exponentially decaying time constants. The simulations proved the feasibility of the method. The influence of experimental noise could be well evaluated. Analysis of the in vivo data showed that in healthy lungs ventilation processes can be more likely characterized by discrete TCs whereas in ARDS lungs continuous distributions of TCs are observed. The temporal behaviour of lung inflation and deflation can be characterized objectively using the described new methodology. This study indicates that continuous distributions of TCs reflect lung ventilation mechanics more accurately compared to discrete TCs.

Confidence intervals and hypothesis testing for the Permutation Entropy with an application to epilepsy

NASA Astrophysics Data System (ADS)

Traversaro, Francisco; O. Redelico, Francisco

2018-04-01

In nonlinear dynamics, and to a lesser extent in other fields, a widely used measure of complexity is the Permutation Entropy. But there is still no known method to determine the accuracy of this measure. There has been little research on the statistical properties of this quantity that characterize time series. The literature describes some resampling methods of quantities used in nonlinear dynamics - as the largest Lyapunov exponent - but these seems to fail. In this contribution, we propose a parametric bootstrap methodology using a symbolic representation of the time series to obtain the distribution of the Permutation Entropy estimator. We perform several time series simulations given by well-known stochastic processes: the 1/fα noise family, and show in each case that the proposed accuracy measure is as efficient as the one obtained by the frequentist approach of repeating the experiment. The complexity of brain electrical activity, measured by the Permutation Entropy, has been extensively used in epilepsy research for detection in dynamical changes in electroencephalogram (EEG) signal with no consideration of the variability of this complexity measure. An application of the parametric bootstrap methodology is used to compare normal and pre-ictal EEG signals.

Describing the epidemiology of rheumatic diseases: methodological aspects.

PubMed

Guillemin, Francis

2012-03-01

Producing descriptive epidemiology data is essential to understand the burden of rheumatic diseases (prevalence) and their dynamic in the population (incidence). No matter how simple such indicators may look, the correct collection of data and the appropriate interpretation of the results face several challenges: distinguishing indicators, facing the costs of obtaining data, using appropriate definition, identifying optimal sources of data, choosing among many survey methods, dealing with estimates precision, and standardizing results. This study describes the underlying methodological difficulties to be overcome so as to make descriptive indicators reliable and interpretable.

Track train dynamics analysis and test program: Methodology development for the derailment safety analysis of six-axle locomotives

NASA Technical Reports Server (NTRS)

Marcotte, P. P.; Mathewson, K. J. R.

1982-01-01

The operational safety of six axle locomotives is analyzed. A locomotive model with corresponding data on suspension characteristics, a method of track defect characterization, and a method of characterizing operational safety are used. A user oriented software package was developed as part of the methodology and was used to study the effect (on operational safety) of various locomotive parameters and operational conditions such as speed, tractive effort, and track curvature. The operational safety of three different locomotive designs was investigated.

A New Finite-Time Observer for Nonlinear Systems: Applications to Synchronization of Lorenz-Like Systems.

PubMed

Aguilar-López, Ricardo; Mata-Machuca, Juan L

2016-01-01

This paper proposes a synchronization methodology of two chaotic oscillators under the framework of identical synchronization and master-slave configuration. The proposed methodology is based on state observer design under the frame of control theory; the observer structure provides finite-time synchronization convergence by cancelling the upper bounds of the main nonlinearities of the chaotic oscillator. The above is showed via an analysis of the dynamic of the so called synchronization error. Numerical experiments corroborate the satisfactory results of the proposed scheme.

A New Finite-Time Observer for Nonlinear Systems: Applications to Synchronization of Lorenz-Like Systems

PubMed Central

Aguilar-López, Ricardo

2016-01-01

This paper proposes a synchronization methodology of two chaotic oscillators under the framework of identical synchronization and master-slave configuration. The proposed methodology is based on state observer design under the frame of control theory; the observer structure provides finite-time synchronization convergence by cancelling the upper bounds of the main nonlinearities of the chaotic oscillator. The above is showed via an analysis of the dynamic of the so called synchronization error. Numerical experiments corroborate the satisfactory results of the proposed scheme. PMID:27738651

Multiphysics Thrust Chamber Modeling for Nuclear Thermal Propulsion

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Cheng, Gary; Chen, Yen-Sen

2006-01-01

The objective of this effort is to develop an efficient and accurate thermo-fluid computational methodology to predict environments for a solid-core, nuclear thermal engine thrust chamber. The computational methodology is based on an unstructured-grid, pressure-based computational fluid dynamics formulation. A two-pronged approach is employed in this effort: A detailed thermo-fluid analysis on a multi-channel flow element for mid-section corrosion investigation; and a global modeling of the thrust chamber to understand the effect of heat transfer on thrust performance. Preliminary results on both aspects are presented.

Deciphering dynamics of clathrin-mediated endocytosis in a living organism

PubMed Central

Heidotting, Spencer P.; Huber, Scott D.

2016-01-01

Current understanding of clathrin-mediated endocytosis (CME) dynamics is based on detection and tracking of fluorescently tagged clathrin coat components within cultured cells. Because of technical limitations inherent to detection and tracking of single fluorescent particles, CME dynamics is not characterized in vivo, so the effects of mechanical cues generated during development of multicellular organisms on formation and dissolution of clathrin-coated structures (CCSs) have not been directly observed. Here, we use growth rates of fluorescence signals obtained from short CCS intensity trace fragments to assess CME dynamics. This methodology does not rely on determining the complete lifespan of individual endocytic assemblies. Therefore, it allows for real-time monitoring of spatiotemporal changes in CME dynamics and is less prone to errors associated with particle detection and tracking. We validate the applicability of this approach to in vivo systems by demonstrating the reduction of CME dynamics during dorsal closure of Drosophila melanogaster embryos. PMID:27458134

Explicit symplectic algorithms based on generating functions for relativistic charged particle dynamics in time-dependent electromagnetic field

NASA Astrophysics Data System (ADS)

Zhang, Ruili; Wang, Yulei; He, Yang; Xiao, Jianyuan; Liu, Jian; Qin, Hong; Tang, Yifa

2018-02-01

Relativistic dynamics of a charged particle in time-dependent electromagnetic fields has theoretical significance and a wide range of applications. The numerical simulation of relativistic dynamics is often multi-scale and requires accurate long-term numerical simulations. Therefore, explicit symplectic algorithms are much more preferable than non-symplectic methods and implicit symplectic algorithms. In this paper, we employ the proper time and express the Hamiltonian as the sum of exactly solvable terms and product-separable terms in space-time coordinates. Then, we give the explicit symplectic algorithms based on the generating functions of orders 2 and 3 for relativistic dynamics of a charged particle. The methodology is not new, which has been applied to non-relativistic dynamics of charged particles, but the algorithm for relativistic dynamics has much significance in practical simulations, such as the secular simulation of runaway electrons in tokamaks.

Walking dynamics of the passive compass-gait model under OGY-based control: Emergence of bifurcations and chaos

NASA Astrophysics Data System (ADS)

Gritli, Hassène; Belghith, Safya

2017-06-01

An analysis of the passive dynamic walking of a compass-gait biped model under the OGY-based control approach using the impulsive hybrid nonlinear dynamics is presented in this paper. We describe our strategy for the development of a simplified analytical expression of a controlled hybrid Poincaré map and then for the design of a state-feedback control. Our control methodology is based mainly on the linearization of the impulsive hybrid nonlinear dynamics around a desired nominal one-periodic hybrid limit cycle. Our analysis of the controlled walking dynamics is achieved by means of bifurcation diagrams. Some interesting nonlinear phenomena are displayed, such as the period-doubling bifurcation, the cyclic-fold bifurcation, the period remerging, the period bubbling and chaos. A comparison between the raised phenomena in the impulsive hybrid nonlinear dynamics and the hybrid Poincaré map under control was also presented.

Fourteenth NASTRAN (R) Users' Colloquium

NASA Technical Reports Server (NTRS)

1986-01-01

The proceedings of a colloquium are presented along with technical papers contributed during the conference. Reviewed are general applications of finite element methodology and the specific application of the NASA Structural Analysis System, NASTRAN, to a variety of static and dynamic sturctural problems.

Effect of Cycling Skills on Bicycle Safety and Comfort Associated with Bicycle Infrastructure and Environment

DOT National Transportation Integrated Search

2017-08-31

This study seeks to improve the methodology for determining the relationship between cycling dynamic performance and roadway environment characteristics across different bicyclists' skill levels. To achieve the goal of this study, an Instrumented Pro...

Investigation of Dynamic Modulus and Flow Number Properties of Asphalt Mixtures In Washington State

DOT National Transportation Integrated Search

2011-11-11

Pavement design is now moving toward more mechanistic based design methodologies for the purpose of producing long : lasting and higher performance pavements in a cost-effective manner. The recent Mechanistic-Empirical pavement : design guide (MEPDG)...

Effective model hierarchies for dynamic and static classical density functional theories

NASA Astrophysics Data System (ADS)

Majaniemi, S.; Provatas, N.; Nonomura, M.

2010-09-01

The origin and methodology of deriving effective model hierarchies are presented with applications to solidification of crystalline solids. In particular, it is discussed how the form of the equations of motion and the effective parameters on larger scales can be obtained from the more microscopic models. It will be shown that tying together the dynamic structure of the projection operator formalism with static classical density functional theories can lead to incomplete (mass) transport properties even though the linearized hydrodynamics on large scales is correctly reproduced. To facilitate a more natural way of binding together the dynamics of the macrovariables and classical density functional theory, a dynamic generalization of density functional theory based on the nonequilibrium generating functional is suggested.

Network destabilization and transition in depression: New methods for studying the dynamics of therapeutic change

PubMed Central

Hayes, Adele M.; Yasinski, Carly; Barnes, J. Ben; Bockting, Claudi L. H.

2015-01-01

The science of dynamic systems is the study of pattern formation and system change. Dynamic systems theory can provide a useful framework for understanding the chronicity of depression and its treatment. We propose a working model of therapeutic change with potential to organize findings from psychopathology and treatment research, suggest new ways to study change, facilitate comparisons across studies, and stimulate treatment innovation. We describe a treatment for depression that we developed to apply principles from dynamic systems theory and then present a program of research to examine the utility of this application. Recent methodological and technological developments are also discussed to further advance the search for mechanisms of therapeutic change. PMID:26197726

Parallel Programming Strategies for Irregular Adaptive Applications

NASA Technical Reports Server (NTRS)

Biswas, Rupak; Biegel, Bryan (Technical Monitor)

2001-01-01

Achieving scalable performance for dynamic irregular applications is eminently challenging. Traditional message-passing approaches have been making steady progress towards this goal; however, they suffer from complex implementation requirements. The use of a global address space greatly simplifies the programming task, but can degrade the performance for such computations. In this work, we examine two typical irregular adaptive applications, Dynamic Remeshing and N-Body, under competing programming methodologies and across various parallel architectures. The Dynamic Remeshing application simulates flow over an airfoil, and refines localized regions of the underlying unstructured mesh. The N-Body experiment models two neighboring Plummer galaxies that are about to undergo a merger. Both problems demonstrate dramatic changes in processor workloads and interprocessor communication with time; thus, dynamic load balancing is a required component.

New perspectives in ecosystem services science as instruments to understand environmental securities

PubMed Central

Villa, Ferdinando; Voigt, Brian; Erickson, Jon D.

2014-01-01

As societal demand for food, water and other life-sustaining resources grows, the science of ecosystem services (ES) is seen as a promising tool to improve our understanding, and ultimately the management, of increasingly uncertain supplies of critical goods provided or supported by natural ecosystems. This promise, however, is tempered by a relatively primitive understanding of the complex systems supporting ES, which as a result are often quantified as static resources rather than as the dynamic expression of human–natural systems. This article attempts to pinpoint the minimum level of detail that ES science needs to achieve in order to usefully inform the debate on environmental securities, and discusses both the state of the art and recent methodological developments in ES in this light. We briefly review the field of ES accounting methods and list some desiderata that we deem necessary, reachable and relevant to address environmental securities through an improved science of ES. We then discuss a methodological innovation that, while only addressing these needs partially, can improve our understanding of ES dynamics in data-scarce situations. The methodology is illustrated and discussed through an application related to water security in the semi-arid landscape of the Great Ruaha river of Tanzania. PMID:24535393

An efficient direct solver for rarefied gas flows with arbitrary statistics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diaz, Manuel A., E-mail: f99543083@ntu.edu.tw; Yang, Jaw-Yen, E-mail: yangjy@iam.ntu.edu.tw; Center of Advanced Study in Theoretical Science, National Taiwan University, Taipei 10167, Taiwan

2016-01-15

A new numerical methodology associated with a unified treatment is presented to solve the Boltzmann–BGK equation of gas dynamics for the classical and quantum gases described by the Bose–Einstein and Fermi–Dirac statistics. Utilizing a class of globally-stiffly-accurate implicit–explicit Runge–Kutta scheme for the temporal evolution, associated with the discrete ordinate method for the quadratures in the momentum space and the weighted essentially non-oscillatory method for the spatial discretization, the proposed scheme is asymptotic-preserving and imposes no non-linear solver or requires the knowledge of fugacity and temperature to capture the flow structures in the hydrodynamic (Euler) limit. The proposed treatment overcomes themore » limitations found in the work by Yang and Muljadi (2011) [33] due to the non-linear nature of quantum relations, and can be applied in studying the dynamics of a gas with internal degrees of freedom with correct values of the ratio of specific heat for the flow regimes for all Knudsen numbers and energy wave lengths. The present methodology is numerically validated with the unified treatment by the one-dimensional shock tube problem and the two-dimensional Riemann problems for gases of arbitrary statistics. Descriptions of ideal quantum gases including rotational degrees of freedom have been successfully achieved under the proposed methodology.« less

A novel methodology for non-linear system identification of battery cells used in non-road hybrid electric vehicles

NASA Astrophysics Data System (ADS)

Unger, Johannes; Hametner, Christoph; Jakubek, Stefan; Quasthoff, Marcus

2014-12-01

An accurate state of charge (SoC) estimation of a traction battery in hybrid electric non-road vehicles, which possess higher dynamics and power densities than on-road vehicles, requires a precise battery cell terminal voltage model. This paper presents a novel methodology for non-linear system identification of battery cells to obtain precise battery models. The methodology comprises the architecture of local model networks (LMN) and optimal model based design of experiments (DoE). Three main novelties are proposed: 1) Optimal model based DoE, which aims to high dynamically excite the battery cells at load ranges frequently used in operation. 2) The integration of corresponding inputs in the LMN to regard the non-linearities SoC, relaxation, hysteresis as well as temperature effects. 3) Enhancements to the local linear model tree (LOLIMOT) construction algorithm, to achieve a physical appropriate interpretation of the LMN. The framework is applicable for different battery cell chemistries and different temperatures, and is real time capable, which is shown on an industrial PC. The accuracy of the obtained non-linear battery model is demonstrated on cells with different chemistries and temperatures. The results show significant improvement due to optimal experiment design and integration of the battery non-linearities within the LMN structure.

Estimation by capture-recapture of recruitment and dispersal over several sites

USGS Publications Warehouse

Lebreton, J.D.; Hines, J.E.; Pradel, R.; Nichols, J.D.; Spendelow, J.A.

2003-01-01

Dispersal in animal populations is intimately linked with accession to reproduction, i.e. recruitment, and population regulation. Dispersal processes are thus a key component of population dynamics to the same extent as reproduction or mortality processes. Despite the growing interest in spatial aspects of population dynamics, the methodology for estimating dispersal, in particular in relation with recruitment, is limited. In many animal populations, in particular vertebrates, the impossibility of following individuals over space and time in an exhaustive way leads to the need to frame the estimation of dispersal in the context of capture-recapture methodology. We present here a class of age-dependent multistate capture-recapture models for the simultaneous estimation of natal dispersal, breeding dispersal, and age-dependent recruitment. These models are suitable for populations in which individuals are marked at birth and then recaptured over several sites. Under simple constraints, they can be used in populations where non-breeders are not observed, as is often the case with colonial waterbirds monitored on their breeding grounds. Biological questions can be addressed by comparing models differing in structure, according to the generalized linear model philosophy broadly used in capture-recapture methodology. We illustrate the potential of this approach by an analysis of recruitment and dispersal in the roseate tern Sterna dougallii.

Removal of Antibiotics in Biological Wastewater Treatment Systems-A Critical Assessment Using the Activated Sludge Modeling Framework for Xenobiotics (ASM-X).

PubMed

Polesel, Fabio; Andersen, Henrik R; Trapp, Stefan; Plósz, Benedek Gy

2016-10-04

Many scientific studies present removal efficiencies for pharmaceuticals in laboratory-, pilot-, and full-scale wastewater treatment plants, based on observations that may be impacted by theoretical and methodological approaches used. In this Critical Review, we evaluated factors influencing observed removal efficiencies of three antibiotics (sulfamethoxazole, ciprofloxacin, tetracycline) in pilot- and full-scale biological treatment systems. Factors assessed include (i) retransformation to parent pharmaceuticals from e.g., conjugated metabolites and analogues, (ii) solid retention time (SRT), (iii) fractions sorbed onto solids, and (iv) dynamics in influent and effluent loading. A recently developed methodology was used, relying on the comparison of removal efficiency predictions (obtained with the Activated Sludge Model for Xenobiotics (ASM-X)) with representative measured data from literature. By applying this methodology, we demonstrated that (a) the elimination of sulfamethoxazole may be significantly underestimated when not considering retransformation from conjugated metabolites, depending on the type (urban or hospital) and size of upstream catchments; (b) operation at extended SRT may enhance antibiotic removal, as shown for sulfamethoxazole; (c) not accounting for fractions sorbed in influent and effluent solids may cause slight underestimation of ciprofloxacin removal efficiency. Using tetracycline as example substance, we ultimately evaluated implications of effluent dynamics and retransformation on environmental exposure and risk prediction.

Pushover Analysis Methodologies: A Tool For Limited Damage Based Design Of Structure For Seismic Vibration

NASA Astrophysics Data System (ADS)

Dutta, Sekhar Chandra; Chakroborty, Suvonkar; Raychaudhuri, Anusrita

Vibration transmitted to the structure during earthquake may vary in magnitude over a wide range. Design methodology should, therefore, enumerates steps so that structures are able to survive in the event of even severe ground motion. However, on account of economic reason, the strengths can be provided to the structures in such a way that the structure remains in elastic range in low to moderate range earthquake and is allowed to undergo inelastic deformation in severe earthquake without collapse. To implement this design philosophy a rigorous nonlinear dynamic analysis is needed to be performed to estimate the inelastic demands. Furthermore, the same is time consuming and requires expertise to judge the results obtained from the same. In this context, the present paper discusses and demonstrates an alternative simple method known as Pushover method, which can be easily used by practicing engineers bypassing intricate nonlinear dynamic analysis and can be thought of as a substitute of the latter. This method is in the process of development and is increasingly becoming popular for its simplicity. The objective of this paper is to emphasize and demonstrate the basic concept, strength and ease of this state of the art methodology for regular use in design offices in performance based seismic design of structures.

Evaluation of Structural Robustness against Column Loss: Methodology and Application to RC Frame Buildings

PubMed Central

Bao, Yihai; Main, Joseph A.; Noh, Sam-Young

2017-01-01

A computational methodology is presented for evaluating structural robustness against column loss. The methodology is illustrated through application to reinforced concrete (RC) frame buildings, using a reduced-order modeling approach for three-dimensional RC framing systems that includes the floor slabs. Comparisons with high-fidelity finite-element model results are presented to verify the approach. Pushdown analyses of prototype buildings under column loss scenarios are performed using the reduced-order modeling approach, and an energy-based procedure is employed to account for the dynamic effects associated with sudden column loss. Results obtained using the energy-based approach are found to be in good agreement with results from direct dynamic analysis of sudden column loss. A metric for structural robustness is proposed, calculated by normalizing the ultimate capacities of the structural system under sudden column loss by the applicable service-level gravity loading and by evaluating the minimum value of this normalized ultimate capacity over all column removal scenarios. The procedure is applied to two prototype 10-story RC buildings, one employing intermediate moment frames (IMFs) and the other employing special moment frames (SMFs). The SMF building, with its more stringent seismic design and detailing, is found to have greater robustness. PMID:28890599

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fogarty, Aoife C., E-mail: fogarty@mpip-mainz.mpg.de; Potestio, Raffaello, E-mail: potestio@mpip-mainz.mpg.de; Kremer, Kurt, E-mail: kremer@mpip-mainz.mpg.de

A fully atomistic modelling of many biophysical and biochemical processes at biologically relevant length- and time scales is beyond our reach with current computational resources, and one approach to overcome this difficulty is the use of multiscale simulation techniques. In such simulations, when system properties necessitate a boundary between resolutions that falls within the solvent region, one can use an approach such as the Adaptive Resolution Scheme (AdResS), in which solvent particles change their resolution on the fly during the simulation. Here, we apply the existing AdResS methodology to biomolecular systems, simulating a fully atomistic protein with an atomistic hydrationmore » shell, solvated in a coarse-grained particle reservoir and heat bath. Using as a test case an aqueous solution of the regulatory protein ubiquitin, we first confirm the validity of the AdResS approach for such systems, via an examination of protein and solvent structural and dynamical properties. We then demonstrate how, in addition to providing a computational speedup, such a multiscale AdResS approach can yield otherwise inaccessible physical insights into biomolecular function. We use our methodology to show that protein structure and dynamics can still be correctly modelled using only a few shells of atomistic water molecules. We also discuss aspects of the AdResS methodology peculiar to biomolecular simulations.« less

Unpacking team process dynamics and emergent phenomena: Challenges, conceptual advances, and innovative methods.

PubMed

Kozlowski, Steve W J; Chao, Georgia T

2018-01-01

Psychologists have studied small-group and team effectiveness for decades, and although there has been considerable progress, there remain significant challenges. Meta-analyses and systematic research have provided solid evidence for core team cognitive, motivational, affective, and behavioral processes that contribute to team effectiveness and empirical support for interventions that enhance team processes (e.g., team design, composition, training, and leadership); there has been substantial evidence for a science of team effectiveness. Nonetheless, there have also been concerns that team processes, which are inherently dynamic, have primarily been assessed as static constructs. Team-level processes and outcomes are multilevel phenomena that emerge, bottom-up from the interactions among team members over time, under the shifting demands of a work context. Thus, theoretical development that appropriately conceptualizes the multiple levels, process dynamics, and emergence of team phenomena over time are essential to advance understanding. Moreover, these conceptual advances necessitate innovative research methodologies to better capture team process dynamics. We explicate this foundation and then describe 2 promising streams of scientific inquiry-team interaction sensors and computational modeling-that are advancing new, unobtrusive measurement techniques and process-oriented research methods focused on understanding the dynamics of cohesion and cognition in teamwork. These are distinct lines of research, each endeavoring to advance the science, but doing so through the development of very different methodologies. We close by discussing the near-term research challenges and the potential long-term evolution of these innovative methods, with an eye toward the future for process-oriented theory and research on team effectiveness. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Gadamerian philosophical hermeneutics as a useful methodological framework for the Delphi technique.

PubMed

Guzys, Diana; Dickson-Swift, Virginia; Kenny, Amanda; Threlkeld, Guinever

2015-01-01

In this article we aim to demonstrate how Gadamerian philosophical hermeneutics may provide a sound methodological framework for researchers using the Delphi Technique (Delphi) in studies exploring health and well-being. Reporting of the use of Delphi in health and well-being research is increasing, but less attention has been given to covering its methodological underpinnings. In Delphi, a structured anonymous conversation between participants is facilitated, via an iterative survey process. Participants are specifically selected for their knowledge and experience with the topic of interest. The purpose of structuring conversation in this manner is to cultivate collective opinion and highlight areas of disagreement, using a process that minimizes the influence of group dynamics. The underlying premise is that the opinion of a collective is more useful than that of an individual. In designing our study into health literacy, Delphi aligned well with our research focus and would enable us to capture collective views. However, we were interested in the methodology that would inform our study. As researchers, we believe that methodology provides the framework and principles for a study and is integral to research integrity. In assessing the suitability of Delphi for our research purpose, we found little information about underpinning methodology. The absence of a universally recognized or consistent methodology associated with Delphi was highlighted through a scoping review we undertook to assist us in our methodological thinking. This led us to consider alternative methodologies, which might be congruent with the key principles of Delphi. We identified Gadamerian philosophical hermeneutics as a methodology that could provide a supportive framework and principles. We suggest that this methodology may be useful in health and well-being studies utilizing the Delphi method.

Gadamerian philosophical hermeneutics as a useful methodological framework for the Delphi technique

PubMed Central

Guzys, Diana; Dickson-Swift, Virginia; Kenny, Amanda; Threlkeld, Guinever

2015-01-01

In this article we aim to demonstrate how Gadamerian philosophical hermeneutics may provide a sound methodological framework for researchers using the Delphi Technique (Delphi) in studies exploring health and well-being. Reporting of the use of Delphi in health and well-being research is increasing, but less attention has been given to covering its methodological underpinnings. In Delphi, a structured anonymous conversation between participants is facilitated, via an iterative survey process. Participants are specifically selected for their knowledge and experience with the topic of interest. The purpose of structuring conversation in this manner is to cultivate collective opinion and highlight areas of disagreement, using a process that minimizes the influence of group dynamics. The underlying premise is that the opinion of a collective is more useful than that of an individual. In designing our study into health literacy, Delphi aligned well with our research focus and would enable us to capture collective views. However, we were interested in the methodology that would inform our study. As researchers, we believe that methodology provides the framework and principles for a study and is integral to research integrity. In assessing the suitability of Delphi for our research purpose, we found little information about underpinning methodology. The absence of a universally recognized or consistent methodology associated with Delphi was highlighted through a scoping review we undertook to assist us in our methodological thinking. This led us to consider alternative methodologies, which might be congruent with the key principles of Delphi. We identified Gadamerian philosophical hermeneutics as a methodology that could provide a supportive framework and principles. We suggest that this methodology may be useful in health and well-being studies utilizing the Delphi method. PMID:25948132

Sparse learning of stochastic dynamical equations

NASA Astrophysics Data System (ADS)

Boninsegna, Lorenzo; Nüske, Feliks; Clementi, Cecilia

2018-06-01

With the rapid increase of available data for complex systems, there is great interest in the extraction of physically relevant information from massive datasets. Recently, a framework called Sparse Identification of Nonlinear Dynamics (SINDy) has been introduced to identify the governing equations of dynamical systems from simulation data. In this study, we extend SINDy to stochastic dynamical systems which are frequently used to model biophysical processes. We prove the asymptotic correctness of stochastic SINDy in the infinite data limit, both in the original and projected variables. We discuss algorithms to solve the sparse regression problem arising from the practical implementation of SINDy and show that cross validation is an essential tool to determine the right level of sparsity. We demonstrate the proposed methodology on two test systems, namely, the diffusion in a one-dimensional potential and the projected dynamics of a two-dimensional diffusion process.

J.A. Schumpeter and T.B. Veblen on economic evolution: the dichotomy between statics and dynamics

PubMed Central

Schütz, Marlies; Rainer, Andreas

2016-01-01

Abstract At present, the discussion on the dichotomy between statics and dynamics is resolved by concentrating on its mathematical meaning. Yet, a simple formalisation masks the underlying methodological discussion. Overcoming this limitation, the paper discusses Schumpeter's and Veblen's viewpoint on dynamic economic systems as systems generating change from within. It contributes to an understanding on their ideas of how economics could become an evolutionary science and on their contributions to elaborate an evolutionary economics. It confronts Schumpeter's with Veblen's perspective on evolutionary economics and provides insight into their evolutionary economic theorising by discussing their ideas on the evolution of capitalism. PMID:28057981

Stochastic aspects of one-dimensional discrete dynamical systems: Benford's law.

PubMed

Snyder, M A; Curry, J H; Dougherty, A M

2001-08-01

Benford's law owes its discovery to the "Grubby Pages Hypothesis," a 19th century observation made by Simon Newcomb that the beginning pages of logarithm books were grubbier than the last few pages, implying that scientists referenced the values toward the front of the books more frequently. If a data set satisfies Benford's law, then it's significant digits will have a logarithmic distribution, which favors smaller significant digits. In this article we demonstrate two ways of creating discrete one-dimensional dynamical systems that satisfy Benford's law. We also develop a numerical simulation methodology that we use to study dynamical systems when analytical results are not readily available.

Computer-aided software development process design

NASA Technical Reports Server (NTRS)

Lin, Chi Y.; Levary, Reuven R.

1989-01-01

The authors describe an intelligent tool designed to aid managers of software development projects in planning, managing, and controlling the development process of medium- to large-scale software projects. Its purpose is to reduce uncertainties in the budget, personnel, and schedule planning of software development projects. It is based on dynamic model for the software development and maintenance life-cycle process. This dynamic process is composed of a number of time-varying, interacting developmental phases, each characterized by its intended functions and requirements. System dynamics is used as a modeling methodology. The resulting Software LIfe-Cycle Simulator (SLICS) and the hybrid expert simulation system of which it is a subsystem are described.

Parallel realities: exploring poverty dynamics using mixed methods in rural Bangladesh.

PubMed

Davisa, Peter; Baulch, Bob

2011-01-01

This paper explores the implications of using two methodological approaches to study poverty dynamics in rural Bangladesh. Using data from a unique longitudinal study, we show how different methods lead to very different assessments of socio-economic mobility. We suggest five ways of reconciling these differences: considering assets in addition to expenditures, proximity to the poverty line, other aspects of well-being, household division, and qualitative recall errors. Considering assets and proximity to the poverty line along with expenditures resolves three-fifths of the qualitative and quantitative differences. Use of such integrated mixed-methods can therefore improve the reliability of poverty dynamics research.

Combination and selection of traffic safety expert judgments for the prevention of driving risks.

PubMed

Cabello, Enrique; Conde, Cristina; de Diego, Isaac Martín; Moguerza, Javier M; Redchuk, Andrés

2012-11-02

In this paper, we describe a new framework to combine experts’ judgments for the prevention of driving risks in a cabin truck. In addition, the methodology shows how to choose among the experts the one whose predictions fit best the environmental conditions. The methodology is applied over data sets obtained from a high immersive cabin truck simulator in natural driving conditions. A nonparametric model, based in Nearest Neighbors combined with Restricted Least Squared methods is developed. Three experts were asked to evaluate the driving risk using a Visual Analog Scale (VAS), in order to measure the driving risk in a truck simulator where the vehicle dynamics factors were stored. Numerical results show that the methodology is suitable for embedding in real time systems.

Advanced Methodology for Simulation of Complex Flows Using Structured Grid Systems

NASA Technical Reports Server (NTRS)

Steinthorsson, Erlendur; Modiano, David

1995-01-01

Detailed simulations of viscous flows in complicated geometries pose a significant challenge to current capabilities of Computational Fluid Dynamics (CFD). To enable routine application of CFD to this class of problems, advanced methodologies are required that employ (a) automated grid generation, (b) adaptivity, (c) accurate discretizations and efficient solvers, and (d) advanced software techniques. Each of these ingredients contributes to increased accuracy, efficiency (in terms of human effort and computer time), and/or reliability of CFD software. In the long run, methodologies employing structured grid systems will remain a viable choice for routine simulation of flows in complex geometries only if genuinely automatic grid generation techniques for structured grids can be developed and if adaptivity is employed more routinely. More research in both these areas is urgently needed.

Behavioral networks as a model for intelligent agents

NASA Technical Reports Server (NTRS)

Sliwa, Nancy E.

1990-01-01

On-going work at NASA Langley Research Center in the development and demonstration of a paradigm called behavioral networks as an architecture for intelligent agents is described. This work focuses on the need to identify a methodology for smoothly integrating the characteristics of low-level robotic behavior, including actuation and sensing, with intelligent activities such as planning, scheduling, and learning. This work assumes that all these needs can be met within a single methodology, and attempts to formalize this methodology in a connectionist architecture called behavioral networks. Behavioral networks are networks of task processes arranged in a task decomposition hierarchy. These processes are connected by both command/feedback data flow, and by the forward and reverse propagation of weights which measure the dynamic utility of actions and beliefs.

Steady-state and dynamic analysis of a jet engine, gas lubricated shaft seal

NASA Technical Reports Server (NTRS)

Shapiro, W.; Colsher, R.

1974-01-01

Dynamic response of a gas-lubricated, jet-engine main shaft seal was analytically established as a function of collar misalignment and secondary seal friction. Response was obtained by a forward integration-in-time (time-transient) scheme, which traces a time history of seal motions in all its degrees of freedom. Results were summarized in the form of a seal tracking map which indicated regions of acceptable collar misalignments and secondary seal friction. Methodology, results and interpretations are comprehensively described.

Interaction Dynamics Between a Flexible Rotor and an Auxiliary Clearance Bearing

NASA Technical Reports Server (NTRS)

Lawen, James L., Jr.; Flowers, George T.

1996-01-01

This study investigates the application of synchronous interaction dynamics methodology to the design of auxiliary bearing systems. The technique is applied to a flexible rotor system and comparisons are made between the behavior predicted by this analysis method and the observed simulation response characteristics. Of particular interest is the influence of coupled shaft/bearing vibration modes on rotordynamical behavior. Experimental studies are also perFormed to validate the simulation results and provide insight into the expected behavior of such a system.

Prospects and expectations for unstructured methods

NASA Technical Reports Server (NTRS)

Baker, Timothy J.

1995-01-01

The last decade has witnessed a vigorous and sustained research effort on unstructured methods for computational fluid dynamics. Unstructured mesh generators and flow solvers have evolved to the point where they are now in use for design purposes throughout the aerospace industry. In this paper we survey the various mesh types, structured as well as unstructured, and examine their relative strengths and weaknesses. We argue that unstructured methodology does offer the best prospect for the next generation of computational fluid dynamics algorithms.

Dynamic Rod Worth Measurement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chao, Y.A.; Chapman, D.M.; Hill, D.J.

2000-12-15

The dynamic rod worth measurement (DRWM) technique is a method of quickly validating the predicted bank worth of control rods and shutdown rods. The DRWM analytic method is based on three-dimensional, space-time kinetic simulations of the rapid rod movements. Its measurement data is processed with an advanced digital reactivity computer. DRWM has been used as the method of bank worth validation at numerous plant startups with excellent results. The process and methodology of DRWM are described, and the measurement results of using DRWM are presented.

Estimation of kinematic parameters in CALIFA galaxies: no-assumption on internal dynamics

NASA Astrophysics Data System (ADS)

García-Lorenzo, B.; Barrera-Ballesteros, J.; CALIFA Team

2016-06-01

We propose a simple approach to homogeneously estimate kinematic parameters of a broad variety of galaxies (elliptical, spirals, irregulars or interacting systems). This methodology avoids the use of any kinematical model or any assumption on internal dynamics. This simple but novel approach allows us to determine: the frequency of kinematic distortions, systemic velocity, kinematic center, and kinematic position angles which are directly measured from the two dimensional-distributions of radial velocities. We test our analysis tools using the CALIFA Survey

Collisional and dynamical processes in moon and planet formation

NASA Technical Reports Server (NTRS)

1979-01-01

The collisional and dynamical processes in moon and planet formation are discussed. A hydrodynamic code of collision calculations, the orbital element changes due to gravitational scattering, a validation of the mass shifting algorithm, a theory of rotations, and the origin of asteroids are studied. A numerical model of planet growth is discussed and a methodology to evaluate the rate at which megaregolith increases its depth as a function of total accumulate number of impacts on an initially smooth, coherent surface is described.

Robot navigation research using the HERMIES mobile robot

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnett, D.L.

1989-01-01

In recent years robot navigation has attracted much attention from researchers around the world. Not only are theoretical studies being simulated on sophisticated computers, but many mobile robots are now used as test vehicles for these theoretical studies. Various algorithms have been perfected for navigation in a known static environment; but navigation in an unknown and dynamic environment poses a much more challenging problem for researchers. Many different methodologies have been developed for autonomous robot navigation, but each methodology is usually restricted to a particular type of environment. One important research focus of the Center for Engineering Systems Advanced researchmore » (CESAR) at Oak Ridge National Laboratory, is autonomous navigation in unknown and dynamic environments using the series of HERMIES mobile robots. The research uses an expert system for high-level planning interfaced with C-coded routines for implementing the plans, and for quick processing of data requested by the expert system. In using this approach, the navigation is not restricted to one methodology since the expert system can activate a rule module for the methodology best suited for the current situation. Rule modules can be added the rule base as they are developed and tested. Modules are being developed or enhanced for navigating from a map, searching for a target, exploring, artificial potential-field navigation, navigation using edge-detection, etc. This paper will report on the various rule modules and methods of navigation in use, or under development at CESAR, using the HERMIES-IIB robot as a testbed. 13 refs., 5 figs., 1 tab.« less

Crashworthiness Analysis of the UMTA State-of-the-Art Cars

DOT National Transportation Integrated Search

1975-10-01

An engineering assessment of the crashworthiness of the UMTA State-of-the-Art Car (SOAC) has been conducted as part of a program to provide safer transportation to urban rail vehicles. Crash dynamics and crashworthiness methodology based on post-yiel...

STATISTICAL METHODOLOGY FOR ESTIMATING PARAMETERS IN PBPK/PD MODELS

EPA Science Inventory

PBPK/PD models are large dynamic models that predict tissue concentration and biological effects of a toxicant before PBPK/PD models can be used in risk assessments in the arena of toxicological hypothesis testing, models allow the consequences of alternative mechanistic hypothes...

Dynamic stiffness characteristics of high eccentricity ratio bearings and seals by perturbation testing

NASA Technical Reports Server (NTRS)

Bently, D. E.; Muszynska, A.

1984-01-01

The complex behavior of cylindrical bearings and seals that are statically loaded to eccentricities in excess of 0.7 are examined. The stiffness algorithms as a function of static load are developed from perturbation methodology by empirical modeling.

Seventh NASTRAN User's Colloquium

NASA Technical Reports Server (NTRS)

1978-01-01

The general application of finite element methodology and the specific application of NASTRAN to a wide variety of static and dynamic structural problems are described. Topics include: fluids and thermal applications, NASTRAN programming, substructuring methods, unique new applications, general auxiliary programs, specific applications, and new capabilities.

Three-dimensional Modeling of Water Quality and Ecology in Narragansett Bay

EPA Science Inventory

This report presents the methodology to apply, calibrate, and validate the three-dimensional water quality and ecological model provided with the Environmental Fluid Dynamics Code (EFDC). The required advection and dispersion mechanisms are generated simultaneously by the EFDC h...

Rotational Dynamics of Proteins from Spin Relaxation Times and Molecular Dynamics Simulations.

PubMed

Ollila, O H Samuli; Heikkinen, Harri A; Iwaï, Hideo

2018-06-14

Conformational fluctuations and rotational tumbling of proteins can be experimentally accessed with nuclear spin relaxation experiments. However, interpretation of molecular dynamics from the experimental data is often complicated, especially for molecules with anisotropic shape. Here, we apply classical molecular dynamics simulations to interpret the conformational fluctuations and rotational tumbling of proteins with arbitrarily anisotropic shape. The direct calculation of spin relaxation times from simulation data did not reproduce the experimental data. This was successfully corrected by scaling the overall rotational diffusion coefficients around the protein inertia axes with a constant factor. The achieved good agreement with experiments allowed the interpretation of the internal and overall dynamics of proteins with significantly anisotropic shape. The overall rotational diffusion was found to be Brownian, having only a short subdiffusive region below 0.12 ns. The presented methodology can be applied to interpret rotational dynamics and conformation fluctuations of proteins with arbitrary anisotropic shape. However, a water model with more realistic dynamical properties is probably required for intrinsically disordered proteins.

A Coherent vorticity preserving eddy-viscosity correction for Large-Eddy Simulation

NASA Astrophysics Data System (ADS)

Chapelier, J.-B.; Wasistho, B.; Scalo, C.

2018-04-01

This paper introduces a new approach to Large-Eddy Simulation (LES) where subgrid-scale (SGS) dissipation is applied proportionally to the degree of local spectral broadening, hence mitigated or deactivated in regions dominated by large-scale and/or laminar vortical motion. The proposed coherent-vorticity preserving (CvP) LES methodology is based on the evaluation of the ratio of the test-filtered to resolved (or grid-filtered) enstrophy, σ. Values of σ close to 1 indicate low sub-test-filter turbulent activity, justifying local deactivation of the SGS dissipation. The intensity of the SGS dissipation is progressively increased for σ < 1 which corresponds to a small-scale spectral broadening. The SGS dissipation is then fully activated in developed turbulence characterized by σ ≤σeq, where the value σeq is derived assuming a Kolmogorov spectrum. The proposed approach can be applied to any eddy-viscosity model, is algorithmically simple and computationally inexpensive. LES of Taylor-Green vortex breakdown demonstrates that the CvP methodology improves the performance of traditional, non-dynamic dissipative SGS models, capturing the peak of total turbulent kinetic energy dissipation during transition. Similar accuracy is obtained by adopting Germano's dynamic procedure albeit at more than twice the computational overhead. A CvP-LES of a pair of unstable periodic helical vortices is shown to predict accurately the experimentally observed growth rate using coarse resolutions. The ability of the CvP methodology to dynamically sort the coherent, large-scale motion from the smaller, broadband scales during transition is demonstrated via flow visualizations. LES of compressible channel are carried out and show a good match with a reference DNS.

Connecting the East and the West, the Local and the Universal: The Methodological Elements of a Transcultural Approach to Bioethics.

PubMed

Nie, Jing-Bao; Fitzgerald, Ruth P

From the outset, cross-cultural and transglobal bioethics has constituted a potent arena for a dynamic public discourse and academic debate alike. But prominent bioethical debates on such issues as the notion of common morality and a distinctive "Asian" bioethics in contrast to a "Western" one reveal some deeply rooted and still popular but seriously problematic methodological habits in approaching cultural differences, most notably, radically dichotomizing the East and the West, the local and the universal. In this paper, a "transcultural" approach to bioethics and cultural studies is proposed. It takes seriously the challenges offered by social sciences, anthropology in particular, towards the development of new methodologies for comparative and global bioethics. The key methodological elements of "transculturalism" include acknowledging the great internal plurality within every culture; highlighting the complexity of cultural differences; upholding the primacy of morality; incorporating a reflexive theory of social power; and promoting changes or progress towards shared and sometimes new moral values.

Modern proposal of methodology for retrieval of characteristic synthetic rainfall hyetographs

NASA Astrophysics Data System (ADS)

Licznar, Paweł; Burszta-Adamiak, Ewa; Łomotowski, Janusz; Stańczyk, Justyna

2017-11-01

Modern engineering workshop of designing and modelling complex drainage systems is based on hydrodynamic modelling and has a probabilistic character. Its practical application requires a change regarding rainfall models accepted at the input. Previously used artificial rainfall models of simplified form, e.g. block precipitation or Euler's type II model rainfall are no longer sufficient. It is noticeable that urgent clarification is needed as regards the methodology of standardized rainfall hyetographs that would take into consideration the specifics of local storm rainfall temporal dynamics. The aim of the paper is to present a proposal for innovative methodology for determining standardized rainfall hyetographs, based on statistical processing of the collection of actual local precipitation characteristics. Proposed methodology is based on the classification of standardized rainfall hyetographs with the use of cluster analysis. Its application is presented on the example of selected rain gauges localized in Poland. Synthetic rainfall hyetographs achieved as a final result may be used for hydrodynamic modelling of sewerage systems, including probabilistic detection of necessary capacity of retention reservoirs.

An enhanced methodology for spacecraft correlation activity using virtual testing tools

NASA Astrophysics Data System (ADS)

Remedia, Marcello; Aglietti, Guglielmo S.; Appolloni, Matteo; Cozzani, Alessandro; Kiley, Andrew

2017-11-01

Test planning and post-test correlation activity have been issues of growing importance in the last few decades and many methodologies have been developed to either quantify or improve the correlation between computational and experimental results. In this article the methodologies established so far are enhanced with the implementation of a recently developed procedure called Virtual Testing. In the context of fixed-base sinusoidal tests (commonly used in the space sector for correlation), there are several factors in the test campaign that affect the behaviour of the satellite and are not normally taken into account when performing analyses: different boundary conditions created by the shaker's own dynamics, non-perfect control system, signal delays etc. All these factors are the core of the Virtual Testing implementation, which will be thoroughly explained in this article and applied to the specific case of Bepi-Colombo spacecraft tested on the ESA QUAD Shaker. Correlation activity will be performed in the various stages of the process, showing important improvements observed after applying the final complete methodology.

Design of feedback control systems for stable plants with saturating actuators

NASA Technical Reports Server (NTRS)

Kapasouris, Petros; Athans, Michael; Stein, Gunter

1988-01-01

A systematic control design methodology is introduced for multi-input/multi-output stable open loop plants with multiple saturations. This new methodology is a substantial improvement over previous heuristic single-input/single-output approaches. The idea is to introduce a supervisor loop so that when the references and/or disturbances are sufficiently small, the control system operates linearly as designed. For signals large enough to cause saturations, the control law is modified in such a way as to ensure stability and to preserve, to the extent possible, the behavior of the linear control design. Key benefits of the methodology are: the modified compensator never produces saturating control signals, integrators and/or slow dynamics in the compensator never windup, the directional properties of the controls are maintained, and the closed loop system has certain guaranteed stability properties. The advantages of the new design methodology are illustrated in the simulation of an academic example and the simulation of the multivariable longitudinal control of a modified model of the F-8 aircraft.

The U. S. Environmental Protection Agency's inhalation RfD methodology: Risk assessment for air toxics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jarabek, A.M.; Menache, M.G.; Overton, J.H. Jr.

1990-10-01

The U.S. Environmental Protection Agency (U.S. EPA) has advocated the establishment of general and scientific guidelines for the evaluation of toxicological data and their use in deriving benchmark values to protect exposed populations from adverse health effects. The Agency's reference dose (RfD) methodology for deriving benchmark values for noncancer toxicity originally addressed risk assessment of oral exposures. This paper presents a brief background on the development of the inhalation reference dose (RfDi) methodology, including concepts and issues related to addressing the dynamics of the respiratory system as the portal of entry. Different dosimetric adjustments are described that were incorporated intomore » the methodology to account for the nature of the inhaled agent (particle or gas) and the site of the observed toxic effects (respiratory or extra-respiratory). Impacts of these adjustments on the extrapolation of toxicity data of inhaled agents for human health risk assessment and future research directions are also discussed.« less

U. S. Environmental Protection Agency's inhalation RFD methodology: Risk assessment for air toxics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jarabek, A.M.; Menache, M.G.; Overton, J.H.

1989-01-01

The U.S. Environmental Protection Agency (U.S. EPA) has advocated the establishment of general and scientific guidelines for the evaluation of toxicological data and their use in deriving benchmark values to protect exposed populations from adverse health effects. The Agency's reference dose (RfD) methodology for deriving benchmark values for noncancer toxicity originally addressed risk assessment of oral exposures. The paper presents a brief background on the development of the inhalation reference dose (RFDi) methodology, including concepts and issues related to addressing the dynamics of the respiratory system as the portal of entry. Different dosimetric adjustments are described that were incorporated intomore » the methodology to account for the nature of the inhaled agent (particle or gas) and the site of the observed toxic effects (respiratory or extrarespiratory). Impacts of these adjustments on the extrapolation of toxicity data of inhaled agents for human health risk assessment and future research directions are also discussed.« less

Integrated Controls-Structures Design Methodology: Redesign of an Evolutionary Test Structure

NASA Technical Reports Server (NTRS)

Maghami, Peiman G.; Gupta, Sandeep; Elliot, Kenny B.; Joshi, Suresh M.

1997-01-01

An optimization-based integrated controls-structures design methodology for a class of flexible space structures is described, and the phase-0 Controls-Structures-Integration evolutionary model, a laboratory testbed at NASA Langley, is redesigned using this integrated design methodology. The integrated controls-structures design is posed as a nonlinear programming problem to minimize the control effort required to maintain a specified line-of-sight pointing performance, under persistent white noise disturbance. Static and dynamic dissipative control strategies are employed for feedback control, and parameters of these controllers are considered as the control design variables. Sizes of strut elements in various sections of the CEM are used as the structural design variables. Design guides for the struts are developed and employed in the integrated design process, to ensure that the redesigned structure can be effectively fabricated. The superiority of the integrated design methodology over the conventional design approach is demonstrated analytically by observing a significant reduction in the average control power needed to maintain specified pointing performance with the integrated design approach.

A new methodology for automated diagnosis of mild cognitive impairment (MCI) using magnetoencephalography (MEG).

PubMed

Amezquita-Sanchez, Juan P; Adeli, Anahita; Adeli, Hojjat

2016-05-15

Mild cognitive impairment (MCI) is a cognitive disorder characterized by memory impairment, greater than expected by age. A new methodology is presented to identify MCI patients during a working memory task using MEG signals. The methodology consists of four steps: In step 1, the complete ensemble empirical mode decomposition (CEEMD) is used to decompose the MEG signal into a set of adaptive sub-bands according to its contained frequency information. In step 2, a nonlinear dynamics measure based on permutation entropy (PE) analysis is employed to analyze the sub-bands and detect features to be used for MCI detection. In step 3, an analysis of variation (ANOVA) is used for feature selection. In step 4, the enhanced probabilistic neural network (EPNN) classifier is applied to the selected features to distinguish between MCI and healthy patients. The usefulness and effectiveness of the proposed methodology are validated using the sensed MEG data obtained experimentally from 18 MCI and 19 control patients. Copyright © 2016 Elsevier B.V. All rights reserved.

Propulsion integration of hypersonic air-breathing vehicles utilizing a top-down design methodology

NASA Astrophysics Data System (ADS)

Kirkpatrick, Brad Kenneth

In recent years, a focus of aerospace engineering design has been the development of advanced design methodologies and frameworks to account for increasingly complex and integrated vehicles. Techniques such as parametric modeling, global vehicle analyses, and interdisciplinary data sharing have been employed in an attempt to improve the design process. The purpose of this study is to introduce a new approach to integrated vehicle design known as the top-down design methodology. In the top-down design methodology, the main idea is to relate design changes on the vehicle system and sub-system level to a set of over-arching performance and customer requirements. Rather than focusing on the performance of an individual system, the system is analyzed in terms of the net effect it has on the overall vehicle and other vehicle systems. This detailed level of analysis can only be accomplished through the use of high fidelity computational tools such as Computational Fluid Dynamics (CFD) or Finite Element Analysis (FEA). The utility of the top-down design methodology is investigated through its application to the conceptual and preliminary design of a long-range hypersonic air-breathing vehicle for a hypothetical next generation hypersonic vehicle (NHRV) program. System-level design is demonstrated through the development of the nozzle section of the propulsion system. From this demonstration of the methodology, conclusions are made about the benefits, drawbacks, and cost of using the methodology.

A Methodology and Implementation for Annotating Digital Images for Context-appropriate Use in an Academic Health Care Environment

PubMed Central

Goede, Patricia A.; Lauman, Jason R.; Cochella, Christopher; Katzman, Gregory L.; Morton, David A.; Albertine, Kurt H.

2004-01-01

Use of digital medical images has become common over the last several years, coincident with the release of inexpensive, mega-pixel quality digital cameras and the transition to digital radiology operation by hospitals. One problem that clinicians, medical educators, and basic scientists encounter when handling images is the difficulty of using business and graphic arts commercial-off-the-shelf (COTS) software in multicontext authoring and interactive teaching environments. The authors investigated and developed software-supported methodologies to help clinicians, medical educators, and basic scientists become more efficient and effective in their digital imaging environments. The software that the authors developed provides the ability to annotate images based on a multispecialty methodology for annotation and visual knowledge representation. This annotation methodology is designed by consensus, with contributions from the authors and physicians, medical educators, and basic scientists in the Departments of Radiology, Neurobiology and Anatomy, Dermatology, and Ophthalmology at the University of Utah. The annotation methodology functions as a foundation for creating, using, reusing, and extending dynamic annotations in a context-appropriate, interactive digital environment. The annotation methodology supports the authoring process as well as output and presentation mechanisms. The annotation methodology is the foundation for a Windows implementation that allows annotated elements to be represented as structured eXtensible Markup Language and stored separate from the image(s). PMID:14527971

Modeling, Analyzing, and Mitigating Dissonance Between Alerting Systems

NASA Technical Reports Server (NTRS)

Song, Lixia; Kuchar, James K.

2003-01-01

Alerting systems are becoming pervasive in process operations, which may result in the potential for dissonance or conflict in information from different alerting systems that suggests different threat levels and/or actions to resolve hazards. Little is currently available to help in predicting or solving the dissonance problem. This thesis presents a methodology to model and analyze dissonance between alerting systems, providing both a theoretical foundation for understanding dissonance and a practical basis from which specific problems can be addressed. A state-space representation of multiple alerting system operation is generalized that can be tailored across a variety of applications. Based on the representation, two major causes of dissonance are identified: logic differences and sensor error. Additionally, several possible types of dissonance are identified. A mathematical analysis method is developed to identify the conditions for dissonance originating from logic differences. A probabilistic analysis methodology is developed to estimate the probability of dissonance originating from sensor error, and to compare the relative contribution to dissonance of sensor error against the contribution from logic differences. A hybrid model, which describes the dynamic behavior of the process with multiple alerting systems, is developed to identify dangerous dissonance space, from which the process can lead to disaster. Methodologies to avoid or mitigate dissonance are outlined. Two examples are used to demonstrate the application of the methodology. First, a conceptual In-Trail Spacing example is presented. The methodology is applied to identify the conditions for possible dissonance, to identify relative contribution of logic difference and sensor error, and to identify dangerous dissonance space. Several proposed mitigation methods are demonstrated in this example. In the second example, the methodology is applied to address the dissonance problem between two air traffic alert and avoidance systems: the existing Traffic Alert and Collision Avoidance System (TCAS) vs. the proposed Airborne Conflict Management system (ACM). Conditions on ACM resolution maneuvers are identified to avoid dynamic dissonance between TCAS and ACM. Also included in this report is an Appendix written by Lee Winder about recent and continuing work on alerting systems design. The application of Markov Decision Process (MDP) theory to complex alerting problems is discussed and illustrated with an abstract example system.

ARC Software and Models

Science.gov Websites

produce software code and methodologies that are transferred to TARDEC and industry partners. These constraints", ASME Dynamic Systems and Control Conference, 2013, DOI:10.1115/DSCC2013-3935 Software Monitoring",IEEE Transactions on Control Systems Technology, DOI:10.1109/TCST.2012.2217143 Fast

A molecular dynamics description of the conformational flexibility of the L-iduronate ring in glycosaminoglycans.

PubMed

Angulo, Jesús; Nieto, Pedro M; Martín-Lomas, Manuel

2003-07-07

For a synthetic hexasaccharide model it is shown that the conformational flexibility of the L-iduronate ring in glycosaminoglycans can be adequately described by using the PME methodology together with simulation protocols suitable for highly charged systems.

The integrated manual and automatic control of complex flight systems

NASA Technical Reports Server (NTRS)

Schmidt, D. K.

1983-01-01

Development of a unified control synthesis methodology for complex and/or non-conventional flight vehicles, and prediction techniques for the handling characteristics of such vehicles are reported. Identification of pilot dynamics and objectives, using time domain and frequency domain methods is proposed.

"International Education" in US Public Schools

ERIC Educational Resources Information Center

Parker, Walter C.

2011-01-01

This study focuses on the recent adoption of "international education" (IE) by US public schools. Theoretically, it conceptualises this phenomenon as a social movement and a dynamic arena of knowledge construction and contestation. Methodologically, it combines fieldwork, interviews and critical discourse analysis. The central finding is…

Dynamic Assessment and the "Interactive Examination"

ERIC Educational Resources Information Center

Jonsson, Anders; Mattheos, Nikos; Svingby, Gunilla; Attstrom, Rolf

2007-01-01

To assess own actions and define individual learning needs is fundamental for professional development. The development of self-assessment skills requires practice and feedback during the course of studies. The "Interactive Examination" is a methodology aiming to assist students developing their self-assessment skills. The present study…

Towards a Pre-Intervention Analytical Methodology

DTIC Science & Technology

2012-08-01

such as concept maps ( Kaste 2007), mind maps, and dynamically interactive networks, available from a variety of proprietary, government, and open...Joint Publication 3-27, Counterterrorism (JP 3-27). Joint Staff. July 2008. Joint Publication 3-57, Civil-Military Operations (JP 3-57). Kaste , R; E

QM/MM Geometry Optimization on Extensive Free-Energy Surfaces for Examination of Enzymatic Reactions and Design of Novel Functional Properties of Proteins.

PubMed

Hayashi, Shigehiko; Uchida, Yoshihiro; Hasegawa, Taisuke; Higashi, Masahiro; Kosugi, Takahiro; Kamiya, Motoshi

2017-05-05

Many remarkable molecular functions of proteins use their characteristic global and slow conformational dynamics through coupling of local chemical states in reaction centers with global conformational changes of proteins. To theoretically examine the functional processes of proteins in atomic detail, a methodology of quantum mechanical/molecular mechanical (QM/MM) free-energy geometry optimization is introduced. In the methodology, a geometry optimization of a local reaction center is performed with a quantum mechanical calculation on a free-energy surface constructed with conformational samples of the surrounding protein environment obtained by a molecular dynamics simulation with a molecular mechanics force field. Geometry optimizations on extensive free-energy surfaces by a QM/MM reweighting free-energy self-consistent field method designed to be variationally consistent and computationally efficient have enabled examinations of the multiscale molecular coupling of local chemical states with global protein conformational changes in functional processes and analysis and design of protein mutants with novel functional properties.

Understanding ageing in older Australians: The contribution of the Dynamic Analyses to Optimise Ageing (DYNOPTA) project to the evidenced base and policy

PubMed Central

Anstey, Kaarin J; Bielak, Allison AM; Birrell, Carole L; Browning, Colette J; Burns, Richard A; Byles, Julie; Kiley, Kim M; Nepal, Binod; Ross, Lesley A; Steel, David; Windsor, Timothy D

2014-01-01

Aim To describe the Dynamic Analyses to Optimise Ageing (DYNOPTA) project and illustrate its contributions to understanding ageing through innovative methodology, and investigations on outcomes based on the project themes. DYNOPTA provides a platform and technical expertise that may be used to combine other national and international datasets. Method The DYNOPTA project has pooled and harmonized data from nine Australian longitudinal studies to create the largest available longitudinal dataset (N=50652) on ageing in Australia. Results A range of findings have resulted from the study to date, including methodological advances, prevalence rates of disease and disability, and mapping trajectories of ageing with and without increasing morbidity. DYNOPTA also forms the basis of a microsimulation model that will provide projections of future costs of disease and disability for the baby boomer cohort. Conclusion DYNOPTA contributes significantly to the Australian evidence-base on ageing to inform key social and health policy domains. PMID:22032767

Tracking the dynamics of the social brain: ERP approaches for social cognitive and affective neuroscience

PubMed Central

Amodio, David M.; Ito, Tiffany A.

2014-01-01

Event-related potential (ERP) approaches to social cognitive and affective neuroscience (SCAN) are not as widely used as other neuroimaging techniques, yet they offer several unique advantages. In particular, the high temporal resolution of ERP measures of neural activity make them ideally suited for studying the dynamic interplay of rapidly unfolding cognitive and affective processes. In this article, we highlight the utility of ERP methods for scientists investigating questions of SCAN. We begin with a brief description of the physiological basis of ERPs and discussion of methodological practices. We then discuss how ERPs may be used to address a range of questions concerning social perception, social cognition, attitudes, affect and self-regulation, with examples of research that has used the ERP approach to contribute important theoretical advances in these areas. Whether used alone or in combination with other techniques, the ERP is an indispensable part of the social and affective neuroscientist’s methodological toolkit. PMID:24319116

Unified Theory for Aircraft Handling Qualities and Adverse Aircraft-Pilot Coupling

NASA Technical Reports Server (NTRS)

Hess, R. A.

1997-01-01

A unified theory for aircraft handling qualities and adverse aircraft-pilot coupling or pilot-induced oscillations is introduced. The theory is based on a structural model of the human pilot. A methodology is presented for the prediction of (1) handling qualities levels; (2) pilot-induced oscillation rating levels; and (3) a frequency range in which pilot-induced oscillations are likely to occur. Although the dynamics of the force-feel system of the cockpit inceptor is included, the methodology will not account for effects attributable to control sensitivity and is limited to single-axis tasks and, at present, to linear vehicle models. The theory is derived from the feedback topology of the structural model and an examination of flight test results for 32 aircraft configurations simulated by the U.S. Air Force/CALSPAN NT-33A and Total In-Flight Simulator variable stability aircraft. An extension to nonlinear vehicle dynamics such as that encountered with actuator saturation is discussed.

New Developments in the Embedded Statistical Coupling Method: Atomistic/Continuum Crack Propagation

NASA Technical Reports Server (NTRS)

Saether, E.; Yamakov, V.; Glaessgen, E.

2008-01-01

A concurrent multiscale modeling methodology that embeds a molecular dynamics (MD) region within a finite element (FEM) domain has been enhanced. The concurrent MD-FEM coupling methodology uses statistical averaging of the deformation of the atomistic MD domain to provide interface displacement boundary conditions to the surrounding continuum FEM region, which, in turn, generates interface reaction forces that are applied as piecewise constant traction boundary conditions to the MD domain. The enhancement is based on the addition of molecular dynamics-based cohesive zone model (CZM) elements near the MD-FEM interface. The CZM elements are a continuum interpretation of the traction-displacement relationships taken from MD simulations using Cohesive Zone Volume Elements (CZVE). The addition of CZM elements to the concurrent MD-FEM analysis provides a consistent set of atomistically-based cohesive properties within the finite element region near the growing crack. Another set of CZVEs are then used to extract revised CZM relationships from the enhanced embedded statistical coupling method (ESCM) simulation of an edge crack under uniaxial loading.

Mapping the spatial and temporal dynamics of the velvet mesquite with MODIS and AVIRIS: Case study at the Santa Rita Experimental Range

NASA Astrophysics Data System (ADS)

Kaurivi, Jorry Zebby Ujama

The general objective of this research is to develop a methodology that will allow mapping and quantifying shrub encroachment with remote sensing. The multitemporal properties of the Moderate Resolution Imaging Spectroradiometer (MODIS) -250m, 16-day vegetation index products were combined with the hyperspectral and high spatial resolution (3.6m) computation of the Airborne Visible-Infrared Imaging Spectrometer (AVIRIS) to detect the dynamics of mesquite and grass/soil matrix at two sites of high (19.5%) and low (5.7%) mesquite cover in the Santa Rita Experimental Range (SRER). MODIS results showed separability between grassland and mesquite based on phenology. Mesquite landscapes had longer green peak starting in April through February, while the grassland only peaked during the monsoon season (July through October). AVIRIS revealed spectral separability, but high variation in the data implicated high heterogeneity in the landscape. Nonetheless, the methodology for larger data was developed in this study and combines ground, air and satellite data.

QM/MM Geometry Optimization on Extensive Free-Energy Surfaces for Examination of Enzymatic Reactions and Design of Novel Functional Properties of Proteins

NASA Astrophysics Data System (ADS)

Hayashi, Shigehiko; Uchida, Yoshihiro; Hasegawa, Taisuke; Higashi, Masahiro; Kosugi, Takahiro; Kamiya, Motoshi

2017-05-01

Many remarkable molecular functions of proteins use their characteristic global and slow conformational dynamics through coupling of local chemical states in reaction centers with global conformational changes of proteins. To theoretically examine the functional processes of proteins in atomic detail, a methodology of quantum mechanical/molecular mechanical (QM/MM) free-energy geometry optimization is introduced. In the methodology, a geometry optimization of a local reaction center is performed with a quantum mechanical calculation on a free-energy surface constructed with conformational samples of the surrounding protein environment obtained by a molecular dynamics simulation with a molecular mechanics force field. Geometry optimizations on extensive free-energy surfaces by a QM/MM reweighting free-energy self-consistent field method designed to be variationally consistent and computationally efficient have enabled examinations of the multiscale molecular coupling of local chemical states with global protein conformational changes in functional processes and analysis and design of protein mutants with novel functional properties.

Investigation of Inner Loop Flight Control Strategies for High-Speed Research

NASA Technical Reports Server (NTRS)

Newman, Brett; Kassem, Ayman

1999-01-01

This report describes the activities and findings conducted under contract NAS1-19858 with NASA Langley Research Center. Subject matter is the investigation of suitable flight control design methodologies and solutions for large, flexible high-speed vehicles. Specifically, methodologies are to address the inner control loops used for stabilization and augmentation of a highly coupled airframe system possibly involving rigid-body motion, structural vibrations, unsteady aerodynamics, and actuator dynamics. Techniques considered in this body of work are primarily conventional-based, and the vehicle of interest is the High-Speed Civil Transport (HSCT). Major findings include 1) current aeroelastic vehicle modeling procedures require further emphasis and refinement, 2) traditional and nontraditional inner loop flight control strategies employing a single feedback loop do not appear sufficient for highly flexible HSCT class vehicles, 3) inner loop flight control systems will, in all likelihood, require multiple interacting feedback loops, and 4) Ref. H HSCT configuration presents major challenges to designing acceptable closed-loop flight dynamics.

Tracking the dynamics of the social brain: ERP approaches for social cognitive and affective neuroscience.

PubMed

Amodio, David M; Bartholow, Bruce D; Ito, Tiffany A

2014-03-01

Event-related potential (ERP) approaches to social cognitive and affective neuroscience (SCAN) are not as widely used as other neuroimaging techniques, yet they offer several unique advantages. In particular, the high temporal resolution of ERP measures of neural activity make them ideally suited for studying the dynamic interplay of rapidly unfolding cognitive and affective processes. In this article, we highlight the utility of ERP methods for scientists investigating questions of SCAN. We begin with a brief description of the physiological basis of ERPs and discussion of methodological practices. We then discuss how ERPs may be used to address a range of questions concerning social perception, social cognition, attitudes, affect and self-regulation, with examples of research that has used the ERP approach to contribute important theoretical advances in these areas. Whether used alone or in combination with other techniques, the ERP is an indispensable part of the social and affective neuroscientist's methodological toolkit.

Novel use patterns of Salvia divinorum: unobtrusive observation using YouTube™.

PubMed

Casselman, Ivan; Heinrich, Michael

2011-12-08

ETHNOPHARMACOLOGICAL RELEVANCE AND AIMS: The traditional use of the Hallucinogenic sage, Salvia divinorum has been of ethnopharmalogical interest for some time. This plant, endemic to Oaxaca Mexico and traditionally used by the Mazatec, is now utilized worldwide for its psychoactive effects. This use demonstrates a novel use pattern which is distinctly different from Mazatec use. This study offers a new methodology to study emerging global plant use and assesses the users' experience with it. The aim of this research was to develop a new methodology to collect and analyze archived data on the World Wide Web, specifically videos which depict Salvia divinorum use. The basis of the methodology for this project was unobtrusive observation which allows the researcher to observe without influencing the event which is being observed. Qualitative, ethnographic data was used in conjunction with quantitative meta data collected by a customized web crawler programed to archive YouTube™ data. Using this methodology enabled us to understand reported uses and the users' experiences as expressed on the World Wide Web. The main result of this research was the documentation of a distinct, novel use pattern of Salvia divinorum which has developed outside of Oaxaca; a use pattern which differs in a number of ways from traditional, Mazatec use. The majority of the YouTube™ videos analyzed were found to present indications of a positive Salvia divinorum experience. This result highlighted the contradiction between ethnographic data and what is reported by the media. Finally the representation of Salvia divinorum on YouTube™ (and by inference the WWW as a whole) is a growing phenomena. While anthropological and more specifically medico-anthropological research has, for many years, embraced the dynamics of cultures, until recently, ethnopharmalogical research has generally focused on 'traditional' plant use, failing to capture the dynamic elements of plant/human interaction and framing research in the past or as decontextualized largely descriptive reports. Global migration and urban environments formed a basis for looking at the interplay of continuity and change. Such cultural dynamics are exacerbated by the opportunities which the WWW offers. Copyright © 2011. Published by Elsevier Ireland Ltd.

Closed-loop, pilot/vehicle analysis of the approach and landing task

NASA Technical Reports Server (NTRS)

Schmidt, D. K.; Anderson, M. R.

1985-01-01

Optimal-control-theoretic modeling and frequency-domain analysis is the methodology proposed to evaluate analytically the handling qualities of higher-order manually controlled dynamic systems. Fundamental to the methodology is evaluating the interplay between pilot workload and closed-loop pilot/vehicle performance and stability robustness. The model-based metric for pilot workload is the required pilot phase compensation. Pilot/vehicle performance and loop stability is then evaluated using frequency-domain techniques. When these techniques were applied to the flight-test data for thirty-two highly-augmented fighter configurations, strong correlation was obtained between the analytical and experimental results.

Hybrid experimental/analytical models of structural dynamics - Creation and use for predictions

NASA Technical Reports Server (NTRS)

Balmes, Etienne

1993-01-01

An original complete methodology for the construction of predictive models of damped structural vibrations is introduced. A consistent definition of normal and complex modes is given which leads to an original method to accurately identify non-proportionally damped normal mode models. A new method to create predictive hybrid experimental/analytical models of damped structures is introduced, and the ability of hybrid models to predict the response to system configuration changes is discussed. Finally a critical review of the overall methodology is made by application to the case of the MIT/SERC interferometer testbed.

Dynamic monitoring of compliant bodies impacting the water surface through local strain measurements

NASA Astrophysics Data System (ADS)

Panciroli, Riccardo; Biscarini, Chiara; Jannelli, Elio; Ubertini, Filippo; Ubertini, Stefano

2016-04-01

The understanding and the experimental characterization of the evolution of impulsive loading is crucial in several fields in structural, mechanical and ocean engineering, naval architecture and aerospace. In this regards, we developed an experimental methodology to reconstruct the deformed shape of compliant bodies subjected to impulsive loadings, as those encountered in water entry events, starting from a finite number of local strain measurements performed through Fiber Bragg Gratings. The paper discusses the potential applications of the proposed methodology for: i) real-time damage detection and structural health monitoring, ii) fatigue assessment and iii) impulsive load estimation.

A Framework for Evaluating and Enhancing Alignment in Self-Regulated Learning Research

PubMed Central

Dent, Amy L.; Hoyle, Rick H.

2015-01-01

We discuss the articles of this special issue with reference to an important yet previously only implicit dimension of study quality: alignment across the theoretical and methodological decisions that collectively define an approach to self-regulated learning. Integrating and extending work by leaders in the field, we propose a framework for evaluating alignment in the way self-regulated learning research is both conducted and reported. Within this framework, the special issue articles provide a springboard for discussing methodological promises and pitfalls of increasingly sophisticated research on the dynamic, contingent, and contextualized features of self-regulated learning. PMID:25825589

Optimization of the computational load of a hypercube supercomputer onboard a mobile robot.

PubMed

Barhen, J; Toomarian, N; Protopopescu, V

1987-12-01

A combinatorial optimization methodology is developed, which enables the efficient use of hypercube multiprocessors onboard mobile intelligent robots dedicated to time-critical missions. The methodology is implemented in terms of large-scale concurrent algorithms based either on fast simulated annealing, or on nonlinear asynchronous neural networks. In particular, analytic expressions are given for the effect of singleneuron perturbations on the systems' configuration energy. Compact neuromorphic data structures are used to model effects such as prec xdence constraints, processor idling times, and task-schedule overlaps. Results for a typical robot-dynamics benchmark are presented.

Lateral stability analysis for X-29A drop model using system identification methodology

NASA Technical Reports Server (NTRS)

Raney, David L.; Batterson, James G.

1989-01-01

A 22-percent dynamically scaled replica of the X-29A forward-swept-wing airplane has been flown in radio-controlled drop tests at the NASA Langley Research Center. A system identification study of the recorded data was undertaken to examine the stability and control derivatives that influence the lateral behavior of this vehicle with particular emphasis on an observed wing rock phenomenon. All major lateral stability derivatives and the damping-in-roll derivative were identified for angles of attack from 5 to 80 degrees by using a data-partitioning methodology and a modified stepwise regression algorithm.

Optimization of the computational load of a hypercube supercomputer onboard a mobile robot

NASA Technical Reports Server (NTRS)

Barhen, Jacob; Toomarian, N.; Protopopescu, V.

1987-01-01

A combinatorial optimization methodology is developed, which enables the efficient use of hypercube multiprocessors onboard mobile intelligent robots dedicated to time-critical missions. The methodology is implemented in terms of large-scale concurrent algorithms based either on fast simulated annealing, or on nonlinear asynchronous neural networks. In particular, analytic expressions are given for the effect of single-neuron perturbations on the systems' configuration energy. Compact neuromorphic data structures are used to model effects such as precedence constraints, processor idling times, and task-schedule overlaps. Results for a typical robot-dynamics benchmark are presented.

Methodology for determining elevon deflections to trim and maneuver the DAST vehicle with negative static margin

NASA Technical Reports Server (NTRS)

Perry, B., III

1982-01-01

The relationships between elevon deflection and static margin using elements from static and dynamic stability and control and from classical control theory are emphasized. Expressions are derived and presented for calculating elevon deflections required to trim the vehicle in lg straight-and-level flight and to perform specified longitudinal and lateral maneuvers. Applications of this methodology are made at several flight conditions for the ARW-2 wing. On the basis of these applications, it appears possible to trim and maneuver the vehicle with the existing elevons at -15% static margin.

Connectivity Measures in EEG Microstructural Sleep Elements.

PubMed

Sakellariou, Dimitris; Koupparis, Andreas M; Kokkinos, Vasileios; Koutroumanidis, Michalis; Kostopoulos, George K

2016-01-01

During Non-Rapid Eye Movement sleep (NREM) the brain is relatively disconnected from the environment, while connectedness between brain areas is also decreased. Evidence indicates, that these dynamic connectivity changes are delivered by microstructural elements of sleep: short periods of environmental stimuli evaluation followed by sleep promoting procedures. The connectivity patterns of the latter, among other aspects of sleep microstructure, are still to be fully elucidated. We suggest here a methodology for the assessment and investigation of the connectivity patterns of EEG microstructural elements, such as sleep spindles. The methodology combines techniques in the preprocessing, estimation, error assessing and visualization of results levels in order to allow the detailed examination of the connectivity aspects (levels and directionality of information flow) over frequency and time with notable resolution, while dealing with the volume conduction and EEG reference assessment. The high temporal and frequency resolution of the methodology will allow the association between the microelements and the dynamically forming networks that characterize them, and consequently possibly reveal aspects of the EEG microstructure. The proposed methodology is initially tested on artificially generated signals for proof of concept and subsequently applied to real EEG recordings via a custom built MATLAB-based tool developed for such studies. Preliminary results from 843 fast sleep spindles recorded in whole night sleep of 5 healthy volunteers indicate a prevailing pattern of interactions between centroparietal and frontal regions. We demonstrate hereby, an opening to our knowledge attempt to estimate the scalp EEG connectivity that characterizes fast sleep spindles via an "EEG-element connectivity" methodology we propose. The application of the latter, via a computational tool we developed suggests it is able to investigate the connectivity patterns related to the occurrence of EEG microstructural elements. Network characterization of specified physiological or pathological EEG microstructural elements can potentially be of great importance in the understanding, identification, and prediction of health and disease.

Connectivity Measures in EEG Microstructural Sleep Elements

PubMed Central

Sakellariou, Dimitris; Koupparis, Andreas M.; Kokkinos, Vasileios; Koutroumanidis, Michalis; Kostopoulos, George K.

2016-01-01

During Non-Rapid Eye Movement sleep (NREM) the brain is relatively disconnected from the environment, while connectedness between brain areas is also decreased. Evidence indicates, that these dynamic connectivity changes are delivered by microstructural elements of sleep: short periods of environmental stimuli evaluation followed by sleep promoting procedures. The connectivity patterns of the latter, among other aspects of sleep microstructure, are still to be fully elucidated. We suggest here a methodology for the assessment and investigation of the connectivity patterns of EEG microstructural elements, such as sleep spindles. The methodology combines techniques in the preprocessing, estimation, error assessing and visualization of results levels in order to allow the detailed examination of the connectivity aspects (levels and directionality of information flow) over frequency and time with notable resolution, while dealing with the volume conduction and EEG reference assessment. The high temporal and frequency resolution of the methodology will allow the association between the microelements and the dynamically forming networks that characterize them, and consequently possibly reveal aspects of the EEG microstructure. The proposed methodology is initially tested on artificially generated signals for proof of concept and subsequently applied to real EEG recordings via a custom built MATLAB-based tool developed for such studies. Preliminary results from 843 fast sleep spindles recorded in whole night sleep of 5 healthy volunteers indicate a prevailing pattern of interactions between centroparietal and frontal regions. We demonstrate hereby, an opening to our knowledge attempt to estimate the scalp EEG connectivity that characterizes fast sleep spindles via an “EEG-element connectivity” methodology we propose. The application of the latter, via a computational tool we developed suggests it is able to investigate the connectivity patterns related to the occurrence of EEG microstructural elements. Network characterization of specified physiological or pathological EEG microstructural elements can potentially be of great importance in the understanding, identification, and prediction of health and disease. PMID:26924980

Complementary dynamic BH3 profiles predict co-operativity between the multi-kinase inhibitor TG02 and the BH3 mimetic ABT-199 in acute myeloid leukaemia cells.

PubMed

Pallis, Monica; Burrows, Francis; Ryan, Jeremy; Grundy, Martin; Seedhouse, Claire; Abdul-Aziz, Amina; Montero, Joan; Letai, Anthony; Russell, Nigel

2017-03-07

Direct co-operation between sensitiser molecules BAD and NOXA in mediating apoptosis suggests that therapeutic agents which sensitise to BAD may complement agents which sensitise to NOXA. Dynamic BH3 profiling is a novel methodology that we have applied to the measurement of complementarity between sensitiser BH3 peptide mimetics and therapeutic agents. Using dynamic BH3 profiling, we show that the agent TG02, which downregulates MCL-1, sensitises to the BCL-2-inhibitory BAD-BH3 peptide, whereas the BCL-2 antagonist ABT-199 sensitises to MCL-1 inhibitory NOXA-BH3 peptide in acute myeloid leukaemia (AML) cells. At the concentrations used, the peptides did not trigger mitochondrial outer membrane permeabilisation in their own right, but primed cells to release Cytochrome C in the presence of an appropriate trigger of a complementary pathway. In KG-1a cells TG02 and ABT-199 synergised to induce apoptosis. In heterogeneous AML patient samples we noted a range of sensitivities to the two agents. Although some individual samples markedly favoured one agent or the other, in the group as a whole the combination of TG02 + ABT-199 was significantly more cytotoxic than either agent individually. We conclude that dynamic NOXA and BAD BH3 profiling is a sensitive methodology for investigating molecular pathways of drug action and complementary mechanisms of chemoresponsiveness.

Stochastic simulations on a model of circadian rhythm generation.

PubMed

Miura, Shigehiro; Shimokawa, Tetsuya; Nomura, Taishin

2008-01-01

Biological phenomena are often modeled by differential equations, where states of a model system are described by continuous real values. When we consider concentrations of molecules as dynamical variables for a set of biochemical reactions, we implicitly assume that numbers of the molecules are large enough so that their changes can be regarded as continuous and they are described deterministically. However, for a system with small numbers of molecules, changes in their numbers are apparently discrete and molecular noises become significant. In such cases, models with deterministic differential equations may be inappropriate, and the reactions must be described by stochastic equations. In this study, we focus a clock gene expression for a circadian rhythm generation, which is known as a system involving small numbers of molecules. Thus it is appropriate for the system to be modeled by stochastic equations and analyzed by methodologies of stochastic simulations. The interlocked feedback model proposed by Ueda et al. as a set of deterministic ordinary differential equations provides a basis of our analyses. We apply two stochastic simulation methods, namely Gillespie's direct method and the stochastic differential equation method also by Gillespie, to the interlocked feedback model. To this end, we first reformulated the original differential equations back to elementary chemical reactions. With those reactions, we simulate and analyze the dynamics of the model using two methods in order to compare them with the dynamics obtained from the original deterministic model and to characterize dynamics how they depend on the simulation methodologies.

The Role of Electronic Excitations on Chemical Reaction Dynamics at Metal, Semiconductor and Nanoparticle Surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tully, John C.

Chemical reactions are often facilitated and steered when carried out on solid surfaces, essential for applications such as heterogeneous catalysis, solar energy conversion, corrosion, materials processing, and many others. A critical factor that can determine the rates and pathways of chemical reactions at surfaces is the efficiency and specificity of energy transfer; how fast does energy move around and where does it go? For reactions on insulator surfaces energy transfer generally moves in and out of vibrations of the adsorbed molecule and the underlying substrate. By contrast, on metal surfaces, metallic nanoparticles and semiconductors, another pathway for energy flow opensmore » up, excitation and de-excitation of electrons. This so-called “nonadiabatic” mechanism often dominates the transfer of energy and can directly impact the course of a chemical reaction. Conventional computational methods such as molecular dynamics simulation do not account for this nonadiabatic behavior. The current DOE-BES funded project has focused on developing the underlying theoretical foundation and the computational methodology for the prediction of nonadiabatic chemical reaction dynamics at surfaces. The research has successfully opened up new methodology and new applications for molecular simulation. In particular, over the last three years, the “Electronic Friction” theory, pioneered by the PI, has now been developed into a stable and accurate computational method that is sufficiently practical to allow first principles “on-the-fly” simulation of chemical reaction dynamics at metal surfaces.« less

IIR filtering based adaptive active vibration control methodology with online secondary path modeling using PZT actuators

NASA Astrophysics Data System (ADS)

Boz, Utku; Basdogan, Ipek

2015-12-01

Structural vibrations is a major cause for noise problems, discomfort and mechanical failures in aerospace, automotive and marine systems, which are mainly composed of plate-like structures. In order to reduce structural vibrations on these structures, active vibration control (AVC) is an effective approach. Adaptive filtering methodologies are preferred in AVC due to their ability to adjust themselves for varying dynamics of the structure during the operation. The filtered-X LMS (FXLMS) algorithm is a simple adaptive filtering algorithm widely implemented in active control applications. Proper implementation of FXLMS requires availability of a reference signal to mimic the disturbance and model of the dynamics between the control actuator and the error sensor, namely the secondary path. However, the controller output could interfere with the reference signal and the secondary path dynamics may change during the operation. This interference problem can be resolved by using an infinite impulse response (IIR) filter which considers feedback of the one or more previous control signals to the controller output and the changing secondary path dynamics can be updated using an online modeling technique. In this paper, IIR filtering based filtered-U LMS (FULMS) controller is combined with online secondary path modeling algorithm to suppress the vibrations of a plate-like structure. The results are validated through numerical and experimental studies. The results show that the FULMS with online secondary path modeling approach has more vibration rejection capabilities with higher convergence rate than the FXLMS counterpart.