7 CFR 51.2284 - Size classification.

Code of Federal Regulations, 2010 CFR

2010-01-01

...: “Halves”, “Pieces and Halves”, “Pieces” or “Small Pieces”. The size of portions of kernels in the lot... consists of 85 percent or more, by weight, half kernels, and the remainder three-fourths half kernels. (See § 51.2285.) (b) Pieces and halves. Lot consists of 20 percent or more, by weight, half kernels, and the...

The Interdictor’s Lot: A Dynamic Model of the Market for Drug Smuggling Services

DTIC Science & Technology

1988-02-01

A RAND NOTE The Interdictor’s Lot: A Dynamic Model of the 00 Market for Drug Smuggling Services Jonathan A. K. Cave, Peter Reuter February 1988. DTIC...Dynamic Model of the Interim Market for Drug Smuggling Services________________ 6. PERFORMING ORG. REPORT NUMBER 7, AUTHOR(s) s. CONTRACT OR GRANT...Economic Models - Narcotics,. Economic Analysis, Interdictions- Smuggling Law Enforcement U - Drugs. 20 ABSTRACT (Continue on ,e~erse side It necessary

COTS Ceramic Chip Capacitors: An Evaluation of the Parts and Assurance Methodologies

NASA Technical Reports Server (NTRS)

Brusse, Jay A.; Sampson, Michael J.

2004-01-01

Commercial-Off-The-Shelf (COTS) multilayer ceramic chip capacitors (MLCCs) are continually evolving to reduce physical size and increase volumetric efficiency. Designers of high reliability aerospace and military systems are attracted to these attributes of COTS MLCCs and would like to take advantage of them while maintaining the high standards for long-term reliable operation they are accustomed io when selecting military qualified established reliability (MIL-ER) MLCCs. However, MIL-ER MLCCs are not available in the full range of small chip sizes with high capacitance as found in today's COTS MLCCs. The objectives for this evaluation were to assess the long-term performance of small case size COTS MLCCs and to identify effective, lower-cost product assurance methodologies. Fifteen (15) lots of COTS X7R dielectric MLCCs from four (4) different manufacturers and two (2) MIL-ER BX dielectric MLCCs from two (2) of the same manufacturers were evaluated. Both 0805 and 0402 chip sizes were included. Several voltage ratings were tested ranging from a high of 50 volts to a low of 6.3 volts. The evaluation consisted of a comprehensive screening and qualification test program based upon MIL-PRF-55681 (i.e., voltage conditioning, thermal shock, moisture resistance, 2000-hour life test, etc.). In addition, several lot characterization tests were performed including Destructive Physical Analysis (DPA), Highly Accelerated Life Test (HALT) and Dielectric Voltage Breakdown Strength. The data analysis included a comparison of the 2000-hour life test results (used as a metric for long-term performance) relative to the screening and characterization test results. Results of this analysis indicate that the long-term life performance of COTS MLCCs is variable -- some lots perform well, some lots perform poorly. DPA and HALT were found to be promising lot characterization tests to identify substandard COTS MLCC lots prior to conducting more expensive screening and qualification tests. The results indicate that lot- specific screening and qualification are still recommended for high reliability applications. One significant and concerning observation is that MIL- type voltage conditioning (100 hours at twice rated voltage, 125 C) was not an effective screen in removing infant mortality parts for the particular lots of COTS MLCCs evaluated.

Single product lot-sizing on unrelated parallel machines with non-decreasing processing times

NASA Astrophysics Data System (ADS)

Eremeev, A.; Kovalyov, M.; Kuznetsov, P.

2018-01-01

We consider a problem in which at least a given quantity of a single product has to be partitioned into lots, and lots have to be assigned to unrelated parallel machines for processing. In one version of the problem, the maximum machine completion time should be minimized, in another version of the problem, the sum of machine completion times is to be minimized. Machine-dependent lower and upper bounds on the lot size are given. The product is either assumed to be continuously divisible or discrete. The processing time of each machine is defined by an increasing function of the lot volume, given as an oracle. Setup times and costs are assumed to be negligibly small, and therefore, they are not considered. We derive optimal polynomial time algorithms for several special cases of the problem. An NP-hard case is shown to admit a fully polynomial time approximation scheme. An application of the problem in energy efficient processors scheduling is considered.

The use of knowledge-based Genetic Algorithm for starting time optimisation in a lot-bucket MRP

NASA Astrophysics Data System (ADS)

Ridwan, Muhammad; Purnomo, Andi

2016-01-01

In production planning, Material Requirement Planning (MRP) is usually developed based on time-bucket system, a period in the MRP is representing the time and usually weekly. MRP has been successfully implemented in Make To Stock (MTS) manufacturing, where production activity must be started before customer demand is received. However, to be implemented successfully in Make To Order (MTO) manufacturing, a modification is required on the conventional MRP in order to make it in line with the real situation. In MTO manufacturing, delivery schedule to the customers is defined strictly and must be fulfilled in order to increase customer satisfaction. On the other hand, company prefers to keep constant number of workers, hence production lot size should be constant as well. Since a bucket in conventional MRP system is representing time and usually weekly, hence, strict delivery schedule could not be accommodated. Fortunately, there is a modified time-bucket MRP system, called as lot-bucket MRP system that proposed by Casimir in 1999. In the lot-bucket MRP system, a bucket is representing a lot, and the lot size is preferably constant. The time to finish every lot could be varying depends on due date of lot. Starting time of a lot must be determined so that every lot has reasonable production time. So far there is no formal method to determine optimum starting time in the lot-bucket MRP system. Trial and error process usually used for it but some time, it causes several lots have very short production time and the lot-bucket MRP would be infeasible to be executed. This paper presents the use of Genetic Algorithm (GA) for optimisation of starting time in a lot-bucket MRP system. Even though GA is well known as powerful searching algorithm, however, improvement is still required in order to increase possibility of GA in finding optimum solution in shorter time. A knowledge-based system has been embedded in the proposed GA as the improvement effort, and it is proven that the improved GA has superior performance when used in solving a lot-bucket MRP problem.

36 CFR 28.12 - Development standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... significant harm to the natural resources of the Seashore. (c) Minimum lot size is 4,000 square feet. A... allowable accessory structure and is calculated in measuring lot occupancy. (h) No sign may be self...

36 CFR 28.12 - Development standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... significant harm to the natural resources of the Seashore. (c) Minimum lot size is 4,000 square feet. A... allowable accessory structure and is calculated in measuring lot occupancy. (h) No sign may be self...

36 CFR 28.12 - Development standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... significant harm to the natural resources of the Seashore. (c) Minimum lot size is 4,000 square feet. A... allowable accessory structure and is calculated in measuring lot occupancy. (h) No sign may be self...

Solving lot-sizing problem with quantity discount and transportation cost

NASA Astrophysics Data System (ADS)

Lee, Amy H. I.; Kang, He-Yau; Lai, Chun-Mei

2013-04-01

Owing to today's increasingly competitive market and ever-changing manufacturing environment, the inventory problem is becoming more complicated to solve. The incorporation of heuristics methods has become a new trend to tackle the complex problem in the past decade. This article considers a lot-sizing problem, and the objective is to minimise total costs, where the costs include ordering, holding, purchase and transportation costs, under the requirement that no inventory shortage is allowed in the system. We first formulate the lot-sizing problem as a mixed integer programming (MIP) model. Next, an efficient genetic algorithm (GA) model is constructed for solving large-scale lot-sizing problems. An illustrative example with two cases in a touch panel manufacturer is used to illustrate the practicality of these models, and a sensitivity analysis is applied to understand the impact of the changes in parameters to the outcomes. The results demonstrate that both the MIP model and the GA model are effective and relatively accurate tools for determining the replenishment for touch panel manufacturing for multi-periods with quantity discount and batch transportation. The contributions of this article are to construct an MIP model to obtain an optimal solution when the problem is not too complicated itself and to present a GA model to find a near-optimal solution efficiently when the problem is complicated.

Assessment of the within- and between-lot variability of Whatman™ FTA(®) DMPK and 903(®) DBS papers and their suitability for the quantitative bioanalysis of small molecules.

PubMed

Luckwell, Jacquelynn; Denniff, Philip; Capper, Stephen; Michael, Paul; Spooner, Neil; Mallender, Philip; Johnson, Barry; Clegg, Sarah; Green, Mark; Ahmad, Sheelan; Woodford, Lynsey

2013-11-01

To ensure that PK data generated from DBS samples are of the highest quality, it is important that the paper substrate is uniform and does not unduly contribute to variability. This study investigated any within and between lot variations for four cellulose paper types: Whatman™ FTA(®) DMPK-A, -B and -C, and 903(®) (GE Healthcare, Buckinghamshire, UK). The substrates were tested to demonstrate manufacturing reproducibility (thickness, weight, chemical coating concentration) and its effect on the size of the DBS produced, and the quantitative data derived from the bioanalysis of human DBS samples containing six compounds of varying physicochemical properties. Within and between lot variations in paper thickness, mass and chemical coating concentration were within acceptable manufacturing limits. No variation in the spot size or bioanalytical data was observed. Bioanalytical results obtained for DBS samples containing a number of analytes spanning a range of chemical space are not affected by the lot used or by the location within a lot.

7 CFR 51.1438 - Size classifications for pieces.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS) United States Standards for Grades of Shelled Pecans Size Classifications § 51.1438 Size classifications for pieces. The size of pecan pieces in a lot may be specified in accordance with one of the size...

Optimal Inspection of Imports to Prevent Invasive Pest Introduction.

PubMed

Chen, Cuicui; Epanchin-Niell, Rebecca S; Haight, Robert G

2018-03-01

The United States imports more than 1 billion live plants annually-an important and growing pathway for introduction of damaging nonnative invertebrates and pathogens. Inspection of imports is one safeguard for reducing pest introductions, but capacity constraints limit inspection effort. We develop an optimal sampling strategy to minimize the costs of pest introductions from trade by posing inspection as an acceptance sampling problem that incorporates key features of the decision context, including (i) simultaneous inspection of many heterogeneous lots, (ii) a lot-specific sampling effort, (iii) a budget constraint that limits total inspection effort, (iv) inspection error, and (v) an objective of minimizing cost from accepted defective units. We derive a formula for expected number of accepted infested units (expected slippage) given lot size, sample size, infestation rate, and detection rate, and we formulate and analyze the inspector's optimization problem of allocating a sampling budget among incoming lots to minimize the cost of slippage. We conduct an empirical analysis of live plant inspection, including estimation of plant infestation rates from historical data, and find that inspections optimally target the largest lots with the highest plant infestation rates, leaving some lots unsampled. We also consider that USDA-APHIS, which administers inspections, may want to continue inspecting all lots at a baseline level; we find that allocating any additional capacity, beyond a comprehensive baseline inspection, to the largest lots with the highest infestation rates allows inspectors to meet the dual goals of minimizing the costs of slippage and maintaining baseline sampling without substantial compromise. © 2017 Society for Risk Analysis.

Optimal production lot size and reorder point of a two-stage supply chain while random demand is sensitive with sales teams' initiatives

NASA Astrophysics Data System (ADS)

Sankar Sana, Shib

2016-01-01

The paper develops a production-inventory model of a two-stage supply chain consisting of one manufacturer and one retailer to study production lot size/order quantity, reorder point sales teams' initiatives where demand of the end customers is dependent on random variable and sales teams' initiatives simultaneously. The manufacturer produces the order quantity of the retailer at one lot in which the procurement cost per unit quantity follows a realistic convex function of production lot size. In the chain, the cost of sales team's initiatives/promotion efforts and wholesale price of the manufacturer are negotiated at the points such that their optimum profits reached nearer to their target profits. This study suggests to the management of firms to determine the optimal order quantity/production quantity, reorder point and sales teams' initiatives/promotional effort in order to achieve their maximum profits. An analytical method is applied to determine the optimal values of the decision variables. Finally, numerical examples with its graphical presentation and sensitivity analysis of the key parameters are presented to illustrate more insights of the model.

Thermal conductivity of austenitic stainless steel, SRM 735, from 5 to 280 K

NASA Technical Reports Server (NTRS)

Hust, J. G.; Sparks, L. L.

1972-01-01

Thermal conductivity and electrical resistivity measurements were conducted on two lots of an austenitic stainless steel. Electrical resistivity measurements were performed on the second lot, both before and after the material was hot-swaged and reannealed to a size 1/10 the original diameter. These measurements indicate that this steel can be swaged and reannealed without an appreciable change in thermal conductivity. Electrical resistivity measurements as well as direct thermal conductivity measurements on several specimens from both lots indicate a material variability in these lots of less than 1% in thermal conductivity.

Broiler Campylobacter Contamination and Human Campylobacteriosis in Iceland ▿ †

PubMed Central

Callicott, Kenneth A.; Harðardóttir, Hjördís; Georgsson, Franklín; Reiersen, Jarle; Friðriksdóttir, Vala; Gunnarsson, Eggert; Michel, Pascal; Bisaillon, Jean-Robert; Kristinsson, Karl G.; Briem, Haraldur; Hiett, Kelli L.; Needleman, David S.; Stern, Norman J.

2008-01-01

To examine whether there is a relationship between the degree of Campylobacter contamination observed in product lots of retail Icelandic broiler chicken carcasses and the incidence of human disease, 1,617 isolates from 327 individual product lots were genetically matched (using the flaA short variable region [SVR[) to 289 isolates from cases of human campylobacteriosis whose onset was within approximately 2 weeks from the date of processing. When there was genetic identity between broiler isolates and human isolates within the appropriate time frame, a retail product lot was classified as implicated in human disease. According to the results of this analysis, there were multiple clusters of human disease linked to the same process lot or lots. Implicated and nonimplicated retail product lots were compared for four lot descriptors: lot size, prevalence, mean contamination, and maximum contamination (as characterized by direct rinse plating). For retail product distributed fresh, Mann-Whitney U tests showed that implicated product lots had significantly (P = 0.0055) higher mean contamination than nonimplicated lots. The corresponding median values were 3.56 log CFU/carcass for implicated lots and 2.72 log CFU/carcass for nonimplicated lots. For frozen retail product, implicated lots were significantly (P = 0.0281) larger than nonimplicated lots. When the time frame was removed, retail product lots containing Campylobacter flaA SVR genotypes also seen in human disease had significantly higher mean and maximum contamination numbers than lots containing no genotypes seen in human disease for both fresh and frozen product. Our results suggest that cases of broiler-borne campylobacteriosis may occur in clusters and that the differences in mean contamination levels may provide a basis for regulatory action that is more specific than a presence-absence standard. PMID:18791017

7 CFR 51.1903 - Size classification.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Size classification. 51.1903 Section 51.1903... STANDARDS) United States Consumer Standards for Fresh Tomatoes Size and Maturity Classification § 51.1903 Size classification. The following terms may be used for describing the size of the tomatoes in any lot...

7 CFR 51.1903 - Size classification.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Size classification. 51.1903 Section 51.1903... STANDARDS) United States Consumer Standards for Fresh Tomatoes Size and Maturity Classification § 51.1903 Size classification. The following terms may be used for describing the size of the tomatoes in any lot...

7 CFR 51.1903 - Size classification.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Size classification. 51.1903 Section 51.1903... STANDARDS) United States Consumer Standards for Fresh Tomatoes Size and Maturity Classification § 51.1903 Size classification. The following terms may be used for describing the size of the tomatoes in any lot...

Negotiation-based Order Lot-Sizing Approach for Two-tier Supply Chain

NASA Astrophysics Data System (ADS)

Chao, Yuan; Lin, Hao Wen; Chen, Xili; Murata, Tomohiro

This paper focuses on a negotiation based collaborative planning process for the determination of order lot-size over multi-period planning, and confined to a two-tier supply chain scenario. The aim is to study how negotiation based planning processes would be used to refine locally preferred ordering patterns, which would consequently affect the overall performance of the supply chain in terms of costs and service level. Minimal information exchanges in the form of mathematical models are suggested to represent the local preferences and used to support the negotiation processes.

Statistical distribution of building lot frontage: application for Tokyo downtown districts

NASA Astrophysics Data System (ADS)

Usui, Hiroyuki

2018-03-01

The frontage of a building lot is the determinant factor of the residential environment. The statistical distribution of building lot frontages shows how the perimeters of urban blocks are shared by building lots for a given density of buildings and roads. For practitioners in urban planning, this is indispensable to identify potential districts which comprise a high percentage of building lots with narrow frontage after subdivision and to reconsider the appropriate criteria for the density of buildings and roads as residential environment indices. In the literature, however, the statistical distribution of building lot frontages and the density of buildings and roads has not been fully researched. In this paper, based on the empirical study in the downtown districts of Tokyo, it is found that (1) a log-normal distribution fits the observed distribution of building lot frontages better than a gamma distribution, which is the model of the size distribution of Poisson Voronoi cells on closed curves; (2) the statistical distribution of building lot frontages statistically follows a log-normal distribution, whose parameters are the gross building density, road density, average road width, the coefficient of variation of building lot frontage, and the ratio of the number of building lot frontages to the number of buildings; and (3) the values of the coefficient of variation of building lot frontages, and that of the ratio of the number of building lot frontages to that of buildings are approximately equal to 0.60 and 1.19, respectively.

7 CFR 51.3417 - Optional test for specific gravity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Optional test for specific gravity. 51.3417 Section 51... § 51.3417 Optional test for specific gravity. Tests to determine specific gravity shall be made in... lot with respect to size and quality. The specific gravity for any lot of potatoes shall be the...

7 CFR 51.3417 - Optional test for specific gravity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Optional test for specific gravity. 51.3417 Section 51... § 51.3417 Optional test for specific gravity. Tests to determine specific gravity shall be made in... lot with respect to size and quality. The specific gravity for any lot of potatoes shall be the...

7 CFR 51.2284 - Size classification.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Size classification. 51.2284 Section 51.2284...) Size Requirements § 51.2284 Size classification. The following classifications are provided to describe... of kernels in the lot shall conform to the requirements of the specified classification as defined...

7 CFR 51.2284 - Size classification.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Size classification. 51.2284 Section 51.2284...) Size Requirements § 51.2284 Size classification. The following classifications are provided to describe... of kernels in the lot shall conform to the requirements of the specified classification as defined...

Effect of Sampling Plans on the Risk of Escherichia coli O157 Illness.

PubMed

Kiermeier, Andreas; Sumner, John; Jenson, Ian

2015-07-01

Australia exports about 150,000 to 200,000 tons of manufacturing beef to the United States annually. Each lot is tested for Escherichia coli O157 using the N-60 sampling protocol, where 60 small pieces of surface meat from each lot of production are tested. A risk assessment of E. coli O157 illness from the consumption of hamburgers made from Australian manufacturing meat formed the basis to evaluate the effect of sample size and amount on the number of illnesses predicted. The sampling plans evaluated included no sampling (resulting in an estimated 55.2 illnesses per annum), the current N-60 plan (50.2 illnesses), N-90 (49.6 illnesses), N-120 (48.4 illnesses), and a more stringent N-60 sampling plan taking five 25-g samples from each of 12 cartons (47.4 illnesses per annum). While sampling may detect some highly contaminated lots, it does not guarantee that all such lots are removed from commerce. It is concluded that increasing the sample size or sample amount from the current N-60 plan would have a very small public health effect.

21 CFR 161.173 - Canned wet pack shrimp in transparent or nontransparent containers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (dorsal tract, back vein, or sand vein). (ii) Deveined shrimp containing not less than 95 percent by...) Acceptable quality level (AQL). The maximum percent of defective sample units permitted in a lot that will be accepted approximately 95 percent of the time. (ii) Sampling plans: Acceptable Quality Level 6.5 Lot size...

Statistical validation of reagent lot change in the clinical chemistry laboratory can confer insights on good clinical laboratory practice.

PubMed

Cho, Min-Chul; Kim, So Young; Jeong, Tae-Dong; Lee, Woochang; Chun, Sail; Min, Won-Ki

2014-11-01

Verification of new lot reagent's suitability is necessary to ensure that results for patients' samples are consistent before and after reagent lot changes. A typical procedure is to measure results of some patients' samples along with quality control (QC) materials. In this study, the results of patients' samples and QC materials in reagent lot changes were analysed. In addition, the opinion regarding QC target range adjustment along with reagent lot changes was proposed. Patients' sample and QC material results of 360 reagent lot change events involving 61 analytes and eight instrument platforms were analysed. The between-lot differences for the patients' samples (ΔP) and the QC materials (ΔQC) were tested by Mann-Whitney U tests. The size of the between-lot differences in the QC data was calculated as multiples of standard deviation (SD). The ΔP and ΔQC values only differed significantly in 7.8% of the reagent lot change events. This frequency was not affected by the assay principle or the QC material source. One SD was proposed for the cutoff for maintaining pre-existing target range after reagent lot change. While non-commutable QC material results were infrequent in the present study, our data confirmed that QC materials have limited usefulness when assessing new reagent lots. Also a 1 SD standard for establishing a new QC target range after reagent lot change event was proposed. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

46 CFR 160.048-5 - Inspections and tests. 1

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Inspections and tests. 1 160.048-5 Section 160.048-5... Inspections and tests. 1 1 The manufacturer of a personal flotation device must meet 33 CFR 181.701 through 33... laboratory. (b) Lot size and sampling. (1) A lot shall consist of not more than 1,000 buoyant cushions. A new...

46 CFR 160.048-5 - Inspections and tests. 1

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Inspections and tests. 1 160.048-5 Section 160.048-5... Inspections and tests. 1 1 The manufacturer of a personal flotation device must meet 33 CFR 181.701 through 33... laboratory. (b) Lot size and sampling. (1) A lot shall consist of not more than 1,000 buoyant cushions. A new...

7 CFR 993.517 - Identification.

Code of Federal Regulations, 2011 CFR

2011-01-01

... numerical or nomenclature designation prescribed in § 993.515, which designation shall not be lacking in... additional information describing in numerical terms the average size count, or particular range of size counts, of the prunes in such lot so long as such numerical terms fall within the range of the size...

7 CFR 993.517 - Identification.

Code of Federal Regulations, 2013 CFR

2013-01-01

... numerical or nomenclature designation prescribed in § 993.515, which designation shall not be lacking in... additional information describing in numerical terms the average size count, or particular range of size counts, of the prunes in such lot so long as such numerical terms fall within the range of the size...

7 CFR 993.517 - Identification.

Code of Federal Regulations, 2014 CFR

2014-01-01

... numerical or nomenclature designation prescribed in § 993.515, which designation shall not be lacking in... additional information describing in numerical terms the average size count, or particular range of size counts, of the prunes in such lot so long as such numerical terms fall within the range of the size...

7 CFR 993.517 - Identification.

Code of Federal Regulations, 2010 CFR

2010-01-01

... numerical or nomenclature designation prescribed in § 993.515, which designation shall not be lacking in... additional information describing in numerical terms the average size count, or particular range of size counts, of the prunes in such lot so long as such numerical terms fall within the range of the size...

7 CFR 993.517 - Identification.

Code of Federal Regulations, 2012 CFR

2012-01-01

... numerical or nomenclature designation prescribed in § 993.515, which designation shall not be lacking in... additional information describing in numerical terms the average size count, or particular range of size counts, of the prunes in such lot so long as such numerical terms fall within the range of the size...

Testing the Forensic Interestingness of Image Files Based on Size and Type

DTIC Science & Technology

2017-09-01

there were still a lot of uninteresting files that were marked as interesting. Also, the results do not show a correlation between the...interesting, but there were still a lot of uninteresting files that were marked as interesting. Also, the results do not show a correlation between...7  IV.  DESCRIPTION OF METHODOLOGY ...........................................................11  A.  TEST SETUP

A Transcultural Model of the Centrality of "Thinking a Lot" in Psychopathologies Across the Globe and the Process of Localization: A Cambodian Refugee Example.

PubMed

Hinton, Devon E; Barlow, David H; Reis, Ria; de Jong, Joop

2016-12-01

We present a general model of why "thinking a lot" is a key presentation of distress in many cultures and examine how "thinking a lot" plays out in the Cambodian cultural context. We argue that the complaint of "thinking a lot" indicates the presence of a certain causal network of psychopathology that is found across cultures, but that this causal network is localized in profound ways. We show, using a Cambodian example, that examining "thinking a lot" in a cultural context is a key way of investigating the local bio-cultural ontology of psychopathology. Among Cambodian refugees, a typical episode of "thinking a lot" begins with ruminative-type negative cognitions, in particular worry and depressive thoughts. Next these negative cognitions may induce mental symptoms (e.g., poor concentration, forgetfulness, and "zoning out") and somatic symptoms (e.g., migraine headache, migraine-like blurry vision such as scintillating scotomas, dizziness, palpitations). Subsequently the very fact of "thinking a lot" and the induced symptoms may give rise to multiple catastrophic cognitions. Soon, as distress escalates, in a kind of looping, other negative cognitions such as trauma memories may be triggered. All these processes are highly shaped by the Cambodian socio-cultural context. The article shows that Cambodian trauma survivors have a locally specific illness reality that centers on dynamic episodes of "thinking a lot," or on what might be called the "thinking a lot" causal network.

Monitoring health interventions – who's afraid of LQAS?

PubMed Central

Pezzoli, Lorenzo; Kim, Sung Hye

2013-01-01

Lot quality assurance sampling (LQAS) is used to evaluate health services. Subunits of a population (lots) are accepted or rejected according to the number of failures in a random sample (N) of a given lot. If failures are greater than decision value (d), we reject the lot and recommend corrective actions in the lot (i.e. intervention area); if they are equal to or less than d, we accept it. We used LQAS to monitor coverage during the last 3 days of a meningitis vaccination campaign in Niger. We selected one health area (lot) per day reporting the lowest administrative coverage in the previous 2 days. In the sampling plan we considered: N to be small enough to allow us to evaluate one lot per day, deciding to sample 16 individuals from the selected villages of each health area, using probability proportionate to population size; thresholds and d to vary according to administrative coverage reported; α ≤5% (meaning that, if we would have conducted the survey 100 times, we would have accepted the lot up to five times when real coverage was at an unacceptable level) and β ≤20% (meaning that we would have rejected the lot up to 20 times, when real coverage was equal or above the satisfactory level). We classified all three lots as with the acceptable coverage. LQAS appeared to be a rapid, simple, and statistically sound method for in-process coverage assessment. We encourage colleagues in the field to consider using LQAS in complement with other monitoring techniques such as house-to-house monitoring. PMID:24206650

Monitoring health interventions--who's afraid of LQAS?

PubMed

Pezzoli, Lorenzo; Kim, Sung Hye

2013-11-08

Lot quality assurance sampling (LQAS) is used to evaluate health services. Subunits of a population (lots) are accepted or rejected according to the number of failures in a random sample (N) of a given lot. If failures are greater than decision value (d), we reject the lot and recommend corrective actions in the lot (i.e. intervention area); if they are equal to or less than d, we accept it. We used LQAS to monitor coverage during the last 3 days of a meningitis vaccination campaign in Niger. We selected one health area (lot) per day reporting the lowest administrative coverage in the previous 2 days. In the sampling plan we considered: N to be small enough to allow us to evaluate one lot per day, deciding to sample 16 individuals from the selected villages of each health area, using probability proportionate to population size; thresholds and d to vary according to administrative coverage reported; α ≤5% (meaning that, if we would have conducted the survey 100 times, we would have accepted the lot up to five times when real coverage was at an unacceptable level) and β ≤20% (meaning that we would have rejected the lot up to 20 times, when real coverage was equal or above the satisfactory level). We classified all three lots as with the acceptable coverage. LQAS appeared to be a rapid, simple, and statistically sound method for in-process coverage assessment. We encourage colleagues in the field to consider using LQAS in complement with other monitoring techniques such as house-to-house monitoring.

Physical and thermal processing of Waste Printed Circuit Boards aiming for the recovery of gold and copper.

PubMed

Ventura, E; Futuro, A; Pinho, S C; Almeida, M F; Dias, J M

2018-06-20

The recovery of electronic waste to obtain secondary raw materials is a subject of high relevance in the context of circular economy. Accordingly, the present work relies on the evaluation of mining separation/concentration techniques (comminution, size screening, magnetic separation and gravity concentration) alone as well as combined with thermal pre-treatment to recover gold and copper from Waste Printed Circuit Boards. For that purpose, Waste Printed Circuit Boards were subjected to physical processing (comminution, size screening in 6 classes from <0.425 mm to > 6.70 mm, magnetic separation and gravity concentration) alone and combined with thermal treatment (200-500 °C), aiming the recovery of gold and copper. Mixed motherboards and graphic cards (Lot 1 and 3) and highly rich components (connectors separated from memory cards, Lot 2) were analyzed. Gold and copper concentrations were determined before and after treatment. Before treatment, concentrations from 0.01 to 0.6 % wt. and from 9 to 20 % wt. were found for gold and copper respectively. The highest concentrations were observed in the size fractions between 0.425 and 1.70 mm. The highest copper concentration was around 35 % wt. (class 0.425-0.85 mm) and when analyzing memory card connectors alone, gold concentrations reached almost 2% in the same class, reflecting the interest of separating such components. The physical treatment alone was more effective for Lot 1/3, compared to Lot 2, allowing recoveries of 67 % wt. and 87 % wt. for gold and copper respectively, mostly due to differences in particles size and shape. The thermal treatment showed unperceptive influence on gold concentration but significant effect for copper concentration, mostly attributed to the size of the copper particles. Concentrations increased in a factor of around 10 when the thermal treatment was performed at 300 °C for the larger particles (1.70-6.70 mm); the best results were obtained at 400 °C for the other sizes, when the highest rate of thermal decomposition of the material occurred. Copyright © 2018 Elsevier Ltd. All rights reserved.

Modeling Altruistic and Aggressive Driver Behavior in a No-Notice Evacuation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brandstetter, Tim; Garrow, Dr. Laurie; Hunter, Dr. Michael

2007-01-01

This study examines the impact of altruistic and aggressive driver behavior on the effectiveness of an evacuation for a section of downtown Atlanta. The study area includes 37 signalized intersections, seven ramps, and 48 parking lots that vary by size, type (lot versus garage), peak volume, and number of ingress and egress points. A detailed microscopic model of the study area was created in VISSIM. Different scenarios examined the impacts of driver behavior on parking lot discharge rates and the loading rates from side streets on primary evacuation routes. A new methodology was created to accurately represent parking lot dischargemore » rates. This study is also unique in that it assumes a "worst case scenario" that occurs with no advance notice during the morning peak period, when vehicles must transition from inbound to outbound routes. Simulation results indicate that while overall network clearance times are similar across scenarios, the distribution of delay on individual routes and across parking lots differ markedly. More equitable solutions (defined as the allocation of delay from parking lots and side streets to main evacuation routes) were observed with altruistic driver behavior.« less

Evaluation of Primary Immunization Coverage of Infants Under Universal Immunization Programme in an Urban Area of Bangalore City Using Cluster Sampling and Lot Quality Assurance Sampling Techniques

PubMed Central

K, Punith; K, Lalitha; G, Suman; BS, Pradeep; Kumar K, Jayanth

2008-01-01

Research Question: Is LQAS technique better than cluster sampling technique in terms of resources to evaluate the immunization coverage in an urban area? Objective: To assess and compare the lot quality assurance sampling against cluster sampling in the evaluation of primary immunization coverage. Study Design: Population-based cross-sectional study. Study Setting: Areas under Mathikere Urban Health Center. Study Subjects: Children aged 12 months to 23 months. Sample Size: 220 in cluster sampling, 76 in lot quality assurance sampling. Statistical Analysis: Percentages and Proportions, Chi square Test. Results: (1) Using cluster sampling, the percentage of completely immunized, partially immunized and unimmunized children were 84.09%, 14.09% and 1.82%, respectively. With lot quality assurance sampling, it was 92.11%, 6.58% and 1.31%, respectively. (2) Immunization coverage levels as evaluated by cluster sampling technique were not statistically different from the coverage value as obtained by lot quality assurance sampling techniques. Considering the time and resources required, it was found that lot quality assurance sampling is a better technique in evaluating the primary immunization coverage in urban area. PMID:19876474

Plenary Speech: Researching Complex Dynamic Systems--"Retrodictive Qualitative Modelling" in the Language Classroom

ERIC Educational Resources Information Center

Dörnyei, Zoltán

2014-01-01

While approaching second language acquisition from a complex dynamic systems perspective makes a lot of intuitive sense, it is difficult for a number of reasons to operationalise such a dynamic approach in research terms. For example, the most common research paradigms in the social sciences tend to examine variables in relative isolation rather…

Immunogenicity and safety of an investigational multicomponent, recombinant, meningococcal serogroup B vaccine (4CMenB) administered concomitantly with routine infant and child vaccinations: results of two randomised trials.

PubMed

Vesikari, Timo; Esposito, Susanna; Prymula, Roman; Ypma, Ellen; Kohl, Igor; Toneatto, Daniela; Dull, Peter; Kimura, Alan

2013-03-09

Meningococcal serogroup B disease disproportionately affects infants. We assessed lot-to-lot consistency, safety and immunogenicity, and the effect of concomitant vaccination on responses to routine vaccines of an investigational multicomponent vaccine (4CMenB) in this population. We did primary and booster phase 3 studies between March 31, 2008, and Aug 16, 2010, in 70 sites in Europe. We used two series of sponsor-supplied, computer-generated randomisation envelopes to allocate healthy 2 month-old infants to receive routine vaccinations (diphtheria-tetanus-acellular pertussis, inactivated poliovirus, hepatitis B plus Haemophilus influenzae type b, and seven-valent pneumococcal vaccine) at 2, 4, and 6 months of age alone, or concomitantly with 4CMenB or serogroup C conjugate vaccine (MenC) in: 1) an open-label, lot-to-lot immunogenicity and safety substudy of three 4CMenB lots compared with routine vaccines alone (1:1:1:1, block size eight); or 2) an observer-blind, lot-to-lot safety substudy of three 4CMenB lots compared with MenC (1:1:1:3, block size six). At 12 months, 4CMenB-primed children from either substudy were randomised (1:1, block size two) to receive 4CMenB booster, with or without measles-mumps-rubella-varicella (MMRV) vaccine. Immunogenicity was assessed by serum bactericidal assay with human complement (hSBA) against serogroup B test strains, and on randomly selected subsets of serum samples for routine vaccines; laboratory personnel were masked to assignment. The first coprimary outcome was lot-to-lot consistency (hSBA geometric mean ratio of all lots between 0·5 and 2·0), and the second was an immune response (hSBA titre ≥5) for each of the three strains. The primary outcome for the booster study was immune response to booster dose. Immunogenicity data for 4CMenB were for the modified intention-to-treat population, including all infants from the open-label substudy who provided serum samples. The safety population included all participants who contributed safety data after at least one dose of study vaccine. These trials are registered with ClinicalTrials.gov, numbers NCT00657709 and NCT00847145. We enrolled 2627 infants in the open-label phase, 1003 in the observer-blind phase, and 1555 in the booster study. Lot-to-lot consistency was shown for the three 4CMenB lots, with the lowest 95% lower confidence limit being 0·74 and the highest upper limit being 1·33. Of 1181–1184 infants tested 1 month after three 4CMenB doses (all lots pooled), 100% (95% CI 99–100) had hSBA titres of 5 or more against strains selective for factor H binding protein and neisserial adhesin A, and 84% (82–86) for New Zealand outer-membrane vesicle. In a subset (n=100), 84% (75–91) of infants had hSBA titres of 5 or more against neisseria heparin binding antigen. At 12 months of age, waning titres were boosted by a fourth dose, such that 95–100% of children had hSBA titres of 5 or more for all antigens, with or without concomitant MMRV. Immune responses to routine vaccines were much the same with or without concomitant 4CMenB, but concomitant vaccination was associated with increased reactogenicity. 77% (1912 of 2478) of infants had fever of 38·5°C or higher after any 4CMenB dose, compared with 45% (295 of 659) after routine vaccines alone and 47% (228 of 490) with MenC, but only two febrile seizures were deemed probably related to 4CMenB. 4CMenB is immunogenic in infants and children aged 12 months with no clinically relevant interference with routine vaccines, but increases reactogenicity when administered concomitantly with routine vaccines. This breakthrough vaccine offers an innovative solution to the major remaining cause of bacterial meningitis in infant and toddlers. Novartis Vaccines and Diagnostics.

The Effects of Rain Garden Size on Performance

EPA Science Inventory

The presentation discusses the effect of rain garden size on the hydrologic and pollutant removal performance of rain garden systems. The slides will summarize data from both the full-scale rain garden project associated with the permeable pavement parking lot as well as the pilo...

Using lot quality assurance sampling to improve immunization coverage in Bangladesh.

PubMed Central

Tawfik, Y.; Hoque, S.; Siddiqi, M.

2001-01-01

OBJECTIVE: To determine areas of low vaccination coverage in five cities in Bangladesh (Chittagong, Dhaka, Khulna, Rajshahi, and Syedpur). METHODS: Six studies using lot quality assurance sampling were conducted between 1995 and 1997 by Basic Support for Institutionalizing Child Survival and the Bangladesh National Expanded Programme on Immunization. FINDINGS: BCG vaccination coverage was acceptable in all lots studied; however, the proportion of lots rejected because coverage of measles vaccination was low ranged from 0% of lots in Syedpur to 12% in Chittagong and 20% in Dhaka's zones 7 and 8. The proportion of lots rejected because an inadequate number of children in the sample had been fully vaccinated varied from 11% in Syedpur to 30% in Dhaka. Additionally, analysis of aggregated, weighted immunization coverage showed that there was a high BCG vaccination coverage (the first administered vaccine) and a low measles vaccination coverage (the last administered vaccine) indicating a high drop-out rate, ranging from 14% in Syedpur to 36% in Dhaka's zone 8. CONCLUSION: In Bangladesh, where resources are limited, results from surveys using lot quality assurance sampling enabled managers of the National Expanded Programme on Immunization to identify areas with poor vaccination coverage. Those areas were targeted to receive focused interventions to improve coverage. Since this sampling method requires only a small sample size and was easy for staff to use, it is feasible for routine monitoring of vaccination coverage. PMID:11436470

7 CFR 42.102 - Definitions, general.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REGULATIONS STANDARDS FOR CONDITION OF FOOD CONTAINERS Definitions § 42.102 Definitions, general. For the... plan consists of first and total sample sizes with associated acceptance and rejection criteria. The... collection of filled food containers of the same size, type, and style. The term shall mean “inspection lot...

The Determination of Production and Distribution Policy in Push-Pull Production Chain with Supply Hub as the Junction Point

NASA Astrophysics Data System (ADS)

Sinaga, A. T.; Wangsaputra, R.

2018-03-01

The development of technology causes the needs of products and services become increasingly complex, diverse, and fluctuating. This causes the level of inter-company dependencies within a production chains increased. To be able to compete, efficiency improvements need to be done collaboratively in the production chain network. One of the efforts to increase efficiency is to harmonize production and distribution activities in the production chain network. This paper describes the harmonization of production and distribution activities by applying the use of push-pull system and supply hub in the production chain between two companies. The research methodology begins with conducting empirical and literature studies, formulating research questions, developing mathematical models, conducting trials and analyses, and taking conclusions. The relationship between the two companies is described in the MINLP mathematical model with the total cost of production chain as the objective function. Decisions generated by the mathematical models are the size of production lot, size of delivery lot, number of kanban, frequency of delivery, and the number of understock and overstock lot.

A hybrid flowshop scheduling model considering dedicated machines and lot-splitting for the solar cell industry

NASA Astrophysics Data System (ADS)

Wang, Li-Chih; Chen, Yin-Yann; Chen, Tzu-Li; Cheng, Chen-Yang; Chang, Chin-Wei

2014-10-01

This paper studies a solar cell industry scheduling problem, which is similar to traditional hybrid flowshop scheduling (HFS). In a typical HFS problem, the allocation of machine resources for each order should be scheduled in advance. However, the challenge in solar cell manufacturing is the number of machines that can be adjusted dynamically to complete the job. An optimal production scheduling model is developed to explore these issues, considering the practical characteristics, such as hybrid flowshop, parallel machine system, dedicated machines, sequence independent job setup times and sequence dependent job setup times. The objective of this model is to minimise the makespan and to decide the processing sequence of the orders/lots in each stage, lot-splitting decisions for the orders and the number of machines used to satisfy the demands in each stage. From the experimental results, lot-splitting has significant effect on shortening the makespan, and the improvement effect is influenced by the processing time and the setup time of orders. Therefore, the threshold point to improve the makespan can be identified. In addition, the model also indicates that more lot-splitting approaches, that is, the flexibility of allocating orders/lots to machines is larger, will result in a better scheduling performance.

Comparison of Two Buyer-Vendor Coordination Models

NASA Astrophysics Data System (ADS)

Diar Astanti, Ririn; Ai, The Jin; Gong, Dah-Chuan; Luong, Hunyh Trung

2018-03-01

This paper develops and compares two mathematical models for describing situation in coordination of buyer and vendor. In this case the vendor which is an Original Equipment Manufacturers (OEMS) of automotive parts, are supplying different type of buyers, i.e. automotive industry, repair shop and automotive dealers. It is well known that automotive industries are operated in Just in Time (JIT) Production Environment, so that the demand behaviour from this buyer has different characteristics than the demand behaviour from other buyers. Two mathematical models are developed in order to depict two different manufacturing strategies as the vendor response dealing with different type of buyers. These strategies are dividing production lot size for each type of buyer and consolidating all buyer’s demand in to single production lot size.

Nanoparticle Treated Stainless Steel Filters for Metal Vapor Sequestration

NASA Astrophysics Data System (ADS)

Murph, Simona E. Hunyadi; Larsen, George K.; Korinko, Paul; Coopersmith, Kaitlin J.; Summer, Ansley J.; Lewis, Rebecca

2017-02-01

The ability to sequester vapor phase radioactive compounds during industrial processes reduces the exposure of workers and the environment to dangerous radioactive materials. Nanomaterials have a lot of potential in this area because they typically demonstrate size- and shape-dependent properties with higher reactivity than bulk. This is due to the increased surface area-to-volume ratio and quantum size effects. In this report, we developed a gold nanomaterial-treated stainless steel filter, namely wools and coupons, that can be efficiently used for zinc vapor sequestration. Without nanoparticle modification, stainless steel coupons do not react or alloy with Zn. Gold nanomaterials were grown onto various stainless steel filters using solution chemistry that is amenable to scaling up. Materials were characterized by electron microscopy, inductively coupled plasma mass spectroscopy and dynamic light scattering before and after exposure to zinc vapors. X-ray diffraction, high-resolution transmission electron microscopy, energy dispersive x-ray spectroscopy mapping and ultraviolet-visible spectroscopy confirm the formation of gold-zinc alloys after Zn vapor exposure. The effect of surface topography on nanoparticle morphology, size and loading density were also investigated, and stainless steel surface defects were found to have an impact on the Au NP growth and subsequently Zn sequestration.

Literature Review on Dynamic Cellular Manufacturing System

NASA Astrophysics Data System (ADS)

Nouri Houshyar, A.; Leman, Z.; Pakzad Moghadam, H.; Ariffin, M. K. A. M.; Ismail, N.; Iranmanesh, H.

2014-06-01

In previous decades, manufacturers faced a lot of challenges because of globalization and high competition in markets. These problems arise from shortening product life cycle, rapid variation in demand of products, and also rapid changes in manufcaturing technologies. Nowadays most manufacturing companies expend considerable attention for improving flexibility and responsiveness in order to overcome these kinds of problems and also meet customer's needs. By considering the trend toward the shorter product life cycle, the manufacturing environment is towards manufacturing a wide variety of parts in small batches [1]. One of the major techniques which are applied for improving manufacturing competitiveness is Cellular Manufacturing System (CMS). CMS is type of manufacturing system which tries to combine flexibility of job shop and also productivity of flow shop. In addition, Dynamic cellular manufacturing system which considers different time periods for the manufacturing system becomes an important topic and attracts a lot of attention to itself. Therefore, this paper made attempt to have a brief review on this issue and focused on all published paper on this subject. Although, this topic gains a lot of attention to itself during these years, none of previous researchers focused on reviewing the literature of that which can be helpful and useful for other researchers who intend to do the research on this topic. Therefore, this paper is the first study which has focused and reviewed the literature of dynamic cellular manufacturing system.

The Preemptive Stocker Dispatching Rule of Automatic Material Handling System in 300 mm Semiconductor Manufacturing Factories

NASA Astrophysics Data System (ADS)

Wang, C. N.; Lin, H. S.; Hsu, H. P.; Wang, Yen-Hui; Chang, Y. P.

2016-04-01

The integrated circuit (IC) manufacturing industry is one of the biggest output industries in this century. The 300mm wafer fabs is the major fab size of this industry. The automatic material handling system (AMHS) has become one of the most concerned issues among semiconductor manufacturers. The major lot delivery of 300mm fabs is used overhead hoist transport (OHT). The traffic jams are happened frequently due to the wide variety of products and big amount of OHTs moving in the fabs. The purpose of this study is to enhance the delivery performance of automatic material handling and reduce the delay and waiting time of product transportation for both hot lots and normal lots. Therefore, this study proposes an effective OHT dispatching rule: preemptive stocker dispatching (PSD). Simulation experiments are conducted and one of the best differentiated preemptive rule, differentiated preemptive dispatching (DPD), is used for comparison. Compared with DPD, The results indicated that PSD rule can reduce average variable delivery time of normal lots by 13.15%, decreasing average variable delivery time of hot lots by 17.67%. Thus, the PSD rule can effectively reduce the delivery time and enhance productivity in 300 mm wafer fabs.

A computational analysis of lower bounds for the economic lot sizing problem in remanufacturing with separate setups

NASA Astrophysics Data System (ADS)

Aishah Syed Ali, Sharifah

2017-09-01

This paper considers economic lot sizing problem in remanufacturing with separate setup (ELSRs), where remanufactured and new products are produced on dedicated production lines. Since this problem is NP-hard in general, which leads to computationally inefficient and low-quality of solutions, we present (a) a multicommodity formulation and (b) a strengthened formulation based on a priori addition of valid inequalities in the space of original variables, which are then compared with the Wagner-Whitin based formulation available in the literature. Computational experiments on a large number of test data sets are performed to evaluate the different approaches. The numerical results show that our strengthened formulation outperforms all the other tested approaches in terms of linear relaxation bounds. Finally, we conclude with future research directions.

7 CFR 51.1437 - Size classifications for halves.

Code of Federal Regulations, 2010 CFR

2010-01-01

... weight of half-kernels after all pieces, particles and dust, shell, center wall, and foreign material..., particles, and dust. In order to allow for variations incident to proper sizing and handling, not more than 15 percent, by weight, of any lot may consist of pieces, particles, and dust: Provided, That not more...

7 CFR 51.1437 - Size classifications for halves.

Code of Federal Regulations, 2012 CFR

2012-01-01

... weight of half-kernels after all pieces, particles and dust, shell, center wall, and foreign material..., particles, and dust. In order to allow for variations incident to proper sizing and handling, not more than 15 percent, by weight, of any lot may consist of pieces, particles, and dust: Provided, That not more...

7 CFR 51.1437 - Size classifications for halves.

Code of Federal Regulations, 2011 CFR

2011-01-01

... weight of half-kernels after all pieces, particles and dust, shell, center wall, and foreign material..., particles, and dust. In order to allow for variations incident to proper sizing and handling, not more than 15 percent, by weight, of any lot may consist of pieces, particles, and dust: Provided, That not more...

How the distance between regional and human mobility behavior affect the epidemic spreading

NASA Astrophysics Data System (ADS)

Wu, Minna; Han, She; Sun, Mei; Han, Dun

2018-02-01

The distance between different regions has a lot of impact on the individuals' mobility behavior. Meanwhile, the individuals' mobility could greatly affect the epidemic propagation way. By researching the individuals' mobility behavior, we establish the coupled dynamic model for individual mobility and transmission of infectious disease. The basic reproduction number is theoretically obtained according to the next-generation matrix method. Through this study, we may get that the stability state of the epidemic system will be prolonged under a higher commuting level. The infection density is almost the same in different regions over a sufficiently long time. The results show that, due to the individual movement, the origin of virus can only speed up or delay the outbreak of infectious diseases, however, it have little impact on the final infection size.

Ab initio study of friction of graphene flake on graphene/graphite or SiC surface

NASA Astrophysics Data System (ADS)

Gulseren, Oguz; Tayran, Ceren; Sayin, Ceren Sibel

Recently, the rich dynamics of graphene flake on graphite or SiC surfaces are revealed from atomic force microcopy experiments. The studies toward to the understanding of microscopic origin of friction are getting a lot of attention. Despite the several studies of these systems using molecular dynamics methods, density functional theory based investigations are limited because of the huge system sizes. In this study, we investigated the frictional force on graphene flake on graphite or SiC surfaces from pseudopotential planewave calculations based on density functional theory. In both cases, graphene flake (24 C) on graphite or SiC surface, bilayer flake is introduced by freezing the top layer as well as the bottom layer of the surface slab. After fixing the load with these frozen layers, we checked the relative motion of the flake over the surface. A minimum energy is reached when the flake is moved on graphene to attain AB stacking. We also conclude that edge reconstruction because of the finite size of the flake is very critical for frictional properties of the flake; therefore the saturation of dangling bonds with hydrogen is also addressed. Not only the symmetric configurations remaining parameter space is extensively studied. Supported by TUBITAK Project No: 114F162. This work is supported by TUBITAK Project No: 114F162.

Evaluation of a Test Article in the L5178Y TK+/-Mouse Lymphoma Mutagenesis Assay with Colony Size Evaluation in the Presence and Absence of Induced Rat Liver S-9 with a Confirmatory Study. Test Article: 3-Nitro-1,2,4-Triazol-5-one (NTO)

DTIC Science & Technology

2008-11-17

B. Mutat. Res. J J 3;173, 1983 INDUC1NG AGENT(.): Aroclor ! 254 Monsanto Lot No, rul5 • 5QOmglkg BIOCHEMISTRY: -PROTEIN 35.8mglml Assayed... Monsanto Lot No, KL615 - SQQmgikg BIOCHEMISTRY: -PROTEIN 40.1 mglml Assayed according to the method of Lowry et al,.)BC 193:265, 1951 using bovine

Evapotranspiration from selected fallowed agricultural fields on the Tule Lake National Wildlife Refuge, California, during May to October 2000

USGS Publications Warehouse

Bidlake, W.R.

2002-01-01

An investigation of evapotranspiration, vegetation quantity and composition, and depth to the water table below the land surface was made at three sites in two fallowed agricultural lots on the 15,800-hectare Tule Lake National Wildlife Refuge in northern California during the 2000 growing season. All three sites had been farmed during 1999, but were not irrigated since the 1999 growing season. Vegetation at the lot C1B and lot 6 stubble sites included weedy species and small grain plants. The lot 6 cover crop site supported a crop of cereal rye that had been planted during the previous winter. Percentage of coverage by live vegetation ranged from 0 to 43.2 percent at the lot C1B site, from approximately 0 to 63.2 percent at the lot 6 stubble site, and it was estimated to range from 0 to greater than 90 percent at the lot 6 cover crop site. Evapotranspiration was measured using the Bowen ratio energy balance technique and it was estimated using a model that was based on the Priestley-Taylor equation and a model that was based on reference evapotranspiration with grass as the reference crop. Total evapotranspiration during May to October varied little among the three evapotranspiration measurement sites, although the timing of evapotranspiration losses did vary among the sites. Total evapotranspiration from the lot C1B site was 426 millimeters, total evapotranspiration from the lot 6 stubble site was 444 millimeters, and total evapotranspiration from the lot 6 cover crop site was 435 millimeters. The months of May to July accounted for approximately 78 percent of the total evapotranspiration from the lot C1B site, approximately 63 percent of the evapotranspiration from the lot 6 stubble site, and approximately 86 percent of the total evapotranspiration from the lot 6 cover crop site. Estimated growing season precipitation accounted for 16 percent of the growing-season evapotranspiration at the lot C1B site and for 17 percent of the growing-season evapotranspiration at the lot 6 stubble and cover crop sites. The ratio of evapotranspiration rate to the reference evapotranspiration rate was strongly correlated with percentage of site coverage by vegetation at the lot C1B and lot 6 stubble sites (correlation coefficient = 0.95, sample size = 6), where percentage of site coverage was determined from quantitative vegetation surveys. It is concluded that evapotranspiration was mediated by the vegetation at all three sites, and that the differences in seasonal timing of evapotranspiration losses were caused by differences in timing of vegetation growth and development and senescence among the sites. Depth to the water table below the land surface at lot C1B ranged from 0.67 meters in early July to greater than 1.39 meters in late August. Depth to the water table at lot 6 ranged from 0.77 meter in late May to greater than 1.40 meters in late August.

46 CFR 160.048-6 - Marking.

Code of Federal Regulations, 2010 CFR

2010-10-01

... lettering: (1) In letters that can be read at a distance of 2 feet: Type IV Personal Flotation Device....); (Model No.). (Name and address of manufacturer or distributor.). (Lot No.). (Size; width, thickness, and...

Proposal of Heuristic Algorithm for Scheduling of Print Process in Auto Parts Supplier

NASA Astrophysics Data System (ADS)

Matsumoto, Shimpei; Okuhara, Koji; Ueno, Nobuyuki; Ishii, Hiroaki

We are interested in the print process on the manufacturing processes of auto parts supplier as an actual problem. The purpose of this research is to apply our scheduling technique developed in university to the actual print process in mass customization environment. Rationalization of the print process is depending on the lot sizing. The manufacturing lead time of the print process is long, and in the present method, production is done depending on worker’s experience and intuition. The construction of an efficient production system is urgent problem. Therefore, in this paper, in order to shorten the entire manufacturing lead time and to reduce the stock, we reexamine the usual method of the lot sizing rule based on heuristic technique, and we propose the improvement method which can plan a more efficient schedule.

High-volume manufacturing device overlay process control

NASA Astrophysics Data System (ADS)

Lee, Honggoo; Han, Sangjun; Woo, Jaeson; Lee, DongYoung; Song, ChangRock; Heo, Hoyoung; Brinster, Irina; Choi, DongSub; Robinson, John C.

2017-03-01

Overlay control based on DI metrology of optical targets has been the primary basis for run-to-run process control for many years. In previous work we described a scenario where optical overlay metrology is performed on metrology targets on a high frequency basis including every lot (or most lots) at DI. SEM based FI metrology is performed ondevice in-die as-etched on an infrequent basis. Hybrid control schemes of this type have been in use for many process nodes. What is new is the relative size of the NZO as compared to the overlay spec, and the need to find more comprehensive solutions to characterize and control the size and variability of NZO at the 1x nm node: sampling, modeling, temporal frequency and control aspects, as well as trade-offs between SEM throughput and accuracy.

Economic lot sizing in a production system with random demand

NASA Astrophysics Data System (ADS)

Lee, Shine-Der; Yang, Chin-Ming; Lan, Shu-Chuan

2016-04-01

An extended economic production quantity model that copes with random demand is developed in this paper. A unique feature of the proposed study is the consideration of transient shortage during the production stage, which has not been explicitly analysed in existing literature. The considered costs include set-up cost for the batch production, inventory carrying cost during the production and depletion stages in one replenishment cycle, and shortage cost when demand cannot be satisfied from the shop floor immediately. Based on renewal reward process, a per-unit-time expected cost model is developed and analysed. Under some mild condition, it can be shown that the approximate cost function is convex. Computational experiments have demonstrated that the average reduction in total cost is significant when the proposed lot sizing policy is compared with those with deterministic demand.

Effect of Prestraining of Recrystallization Temperature and Mechanical Properties of Commercial, Sintered, Wrought Molybdenum

NASA Technical Reports Server (NTRS)

Dike, Kenneth C; Long, Roger A

1953-01-01

Given three presumably identical lots of commercial, sintered, wrought molybdenum, the 1-hour recrystallization temperature of one lot remained above 2900 F by limiting the amount of effective restraining to 35 percent or less. Different recrystallization temperatures were obtained in various atmospheres, the highest in argon and the lowest in hydrogen. Metal thus fabricated and then stress-relieved possessed an ultimate tensile strength at room temperature within 10 percent of metal swaged 99 percent and also possessed equivalent ductility. At 1800 F, equivalent strength and ductility was obtained irrespective of the amount of swaging over the range of 10 to 99 percent. The amount of swaging greatly influenced the recrystallized grain size but the difference in grain size is not the major controlling factor which determines whether recrystallized molybdenum is ductile or brittle at room temperature.

Size-Resolved Ultrafine Particle Deposition and Brownian Coagulation from Gasoline Vehicle Exhaust in an Environmental Test Chamber.

PubMed

Zhao, Yu; Wang, Fang; Zhao, Jianing

2015-10-20

Size-resolved deposition rates and Brownian coagulation of particles between 20 and 900 nm (mobility diameter) were estimated in a well-mixed environmental chamber from a gasoline vehicle exhaust with a total peak particle concentration of 10(5)-10(6) particles/cm(3) at 12.24-25.22 °C. A deposition theory with modified friction velocity and coagulation model was also employed to predict particle concentration decay. Initially during particle decay, approximately 85% or more of the particles had diameters of <100 nm. Particle deposition rates with standard deviations were highly dependent on particle size ranges, and varied from 0.012 ± 0.003 to 0.48 ± 0.02 h(-1). In the experiment, the friction velocity obtained was in the range 1.5-2.5 cm/s. The most explainable fractal dimension and Hamaker constant in coagulation model were 2.5-3 and 20 kT, respectively, and the contribution from coagulation dominated the total particle decay during the first 1 h of decay. It is considered that the modified friction velocity and best fitted fractal dimension and Hamaker constants could be further used to analyze gasoline vehicle exhaust particle dynamics and assess human exposure to vehicle particle pollutants in urban areas, tunnels, and underground parking lots.

Nanoparticle treated stainless steel filters for metal vapor sequestration

DOE PAGES

Murph, Simona E. Hunyadi; Larsen, George K.; Korinko, Paul; ...

2016-12-07

The ability to sequester vapor phase radioactive compounds during industrial processes reduces the exposure of workers and the environment to dangerous radioactive materials. Nanomaterials have a lot of potential in this area because they typically demonstrate size- and shape-dependent properties with higher reactivity than bulk. This is due to the increased surface area-to-volume ratio and quantum size effects. In this report, we developed a gold nanomaterial-treated stainless steel filter, namely wools and coupons, that can be efficiently used for zinc vapor sequestration. Without nanoparticle modification, stainless steel coupons do not react or alloy with Zn. Gold nanomaterials were grown ontomore » various stainless steel filters using solution chemistry that is amenable to scaling up. Materials were characterized by electron microscopy, inductively coupled plasma mass spectroscopy and dynamic light scattering before and after exposure to zinc vapors. X-ray diffraction, high-resolution transmission electron microscopy, energy dispersive x-ray spectroscopy mapping and ultraviolet-visible spectroscopy confirm the formation of gold-zinc alloys after Zn vapor exposure. Furthermore, the effect of surface topography on nanoparticle morphology, size and loading density were also investigated, and stainless steel surface defects were found to have an impact on the Au NP growth and subsequently Zn sequestration.« less

Nanoparticle treated stainless steel filters for metal vapor sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murph, Simona E. Hunyadi; Larsen, George K.; Korinko, Paul

The ability to sequester vapor phase radioactive compounds during industrial processes reduces the exposure of workers and the environment to dangerous radioactive materials. Nanomaterials have a lot of potential in this area because they typically demonstrate size- and shape-dependent properties with higher reactivity than bulk. This is due to the increased surface area-to-volume ratio and quantum size effects. In this report, we developed a gold nanomaterial-treated stainless steel filter, namely wools and coupons, that can be efficiently used for zinc vapor sequestration. Without nanoparticle modification, stainless steel coupons do not react or alloy with Zn. Gold nanomaterials were grown ontomore » various stainless steel filters using solution chemistry that is amenable to scaling up. Materials were characterized by electron microscopy, inductively coupled plasma mass spectroscopy and dynamic light scattering before and after exposure to zinc vapors. X-ray diffraction, high-resolution transmission electron microscopy, energy dispersive x-ray spectroscopy mapping and ultraviolet-visible spectroscopy confirm the formation of gold-zinc alloys after Zn vapor exposure. Furthermore, the effect of surface topography on nanoparticle morphology, size and loading density were also investigated, and stainless steel surface defects were found to have an impact on the Au NP growth and subsequently Zn sequestration.« less

Quantitative Survey of Laypersons' Attitudes Toward Organ Transplantation in Japan.

PubMed

Okita, T; Hsu, E; Aizawa, K; Nakada, H; Toya, W; Matsui, K

In comparison with foreign countries, living-organ transplantations (LOT) have been performed more frequently than dead organ transplants, including brain-dead organ transplantation (BOT) in Japan. This situation has given rise to organ transplantation tourism. Therefore, we clarify laypersons' preferences regarding organ transplantation that are producing the current situation in Japan, to suggest a possible framework for further efforts. Voluntary completion of a quantitative and anonymous survey was promoted online (a sample size of 1030). The questionnaire had two types of variables concerning demographic characteristics and organ transplantation-related issues. LOT was favored over BOT. However, for willingness to donate to family members, the participants showed a significantly more positive attitude toward brain-dead organ donors (BODs) than living organ donors (LODs). In the evaluation of each transplantation technology, BOT and LOT were positioned in the middle, between transplantation that does not depend on others and the utilization of animal organs. Although LOT was favored over BOT, for participants hypothesized to be in a position to donate and receive organs, BODs received a conversely better reputation than LODs. Our survey and discussion suggest that the present conditions of organ transplantation in Japan might be because there is a lack of deliberation on transplantation tourism and LOT. Therefore, more surveys concerning LOT cases and the implications of avoidance of organs from brain-dead bodies, coupled with more discussions based on these surveys, are necessary to formulate a Japanese transplantation policy for the future. Copyright © 2017 Elsevier Inc. All rights reserved.

Poles, Parking Lots, and Mount Piton: Classroom Activities that Combine Astronomy, History, and Mathematics

ERIC Educational Resources Information Center

Madden, Sean P.; Comstock, Jocelyn M.; Downing, James P.

2006-01-01

This article describes how a series of lessons might be used to allow students to discover the size of the Earth, the distance to the Moon, the size of the Moon, and the altitude of Mount Piton on the Moon. Measurement with a sextant, principles of geometry and trigonometry, and historically important scientists and mathematicians are discussed.

The effect of clustering on lot quality assurance sampling: a probabilistic model to calculate sample sizes for quality assessments

PubMed Central

2013-01-01

Background Traditional Lot Quality Assurance Sampling (LQAS) designs assume observations are collected using simple random sampling. Alternatively, randomly sampling clusters of observations and then individuals within clusters reduces costs but decreases the precision of the classifications. In this paper, we develop a general framework for designing the cluster(C)-LQAS system and illustrate the method with the design of data quality assessments for the community health worker program in Rwanda. Results To determine sample size and decision rules for C-LQAS, we use the beta-binomial distribution to account for inflated risk of errors introduced by sampling clusters at the first stage. We present general theory and code for sample size calculations. The C-LQAS sample sizes provided in this paper constrain misclassification risks below user-specified limits. Multiple C-LQAS systems meet the specified risk requirements, but numerous considerations, including per-cluster versus per-individual sampling costs, help identify optimal systems for distinct applications. Conclusions We show the utility of C-LQAS for data quality assessments, but the method generalizes to numerous applications. This paper provides the necessary technical detail and supplemental code to support the design of C-LQAS for specific programs. PMID:24160725

The effect of clustering on lot quality assurance sampling: a probabilistic model to calculate sample sizes for quality assessments.

PubMed

Hedt-Gauthier, Bethany L; Mitsunaga, Tisha; Hund, Lauren; Olives, Casey; Pagano, Marcello

2013-10-26

Traditional Lot Quality Assurance Sampling (LQAS) designs assume observations are collected using simple random sampling. Alternatively, randomly sampling clusters of observations and then individuals within clusters reduces costs but decreases the precision of the classifications. In this paper, we develop a general framework for designing the cluster(C)-LQAS system and illustrate the method with the design of data quality assessments for the community health worker program in Rwanda. To determine sample size and decision rules for C-LQAS, we use the beta-binomial distribution to account for inflated risk of errors introduced by sampling clusters at the first stage. We present general theory and code for sample size calculations.The C-LQAS sample sizes provided in this paper constrain misclassification risks below user-specified limits. Multiple C-LQAS systems meet the specified risk requirements, but numerous considerations, including per-cluster versus per-individual sampling costs, help identify optimal systems for distinct applications. We show the utility of C-LQAS for data quality assessments, but the method generalizes to numerous applications. This paper provides the necessary technical detail and supplemental code to support the design of C-LQAS for specific programs.

Flow Microscopy Imaging Is Sensitive to Characteristics of Subvisible Particles in Peginesatide Formulations Associated With Severe Adverse Reactions.

PubMed

Daniels, Austin L; Randolph, Theodore W

2018-05-01

The presence of subvisible particles in formulations of therapeutic proteins is a risk factor for adverse immune responses. Although the immunogenic potential of particulate contaminants likely depends on particle structural characteristics (e.g., composition, size, and shape), exact structure-immunogenicity relationships are unknown. Images recorded by flow imaging microscopy reflect information about particle morphology, but flow microscopy is typically used to determine only particle size distributions, neglecting information on particle morphological features that may be immunologically relevant. We recently developed computational techniques that utilize the Kullback-Leibler divergence and multidimensional scaling to compare the morphological properties of particles in sets of flow microscopy images. In the current work, we combined these techniques with expectation maximization cluster analyses and used them to compare flow imaging microscopy data sets that had been collected by the U.S. Food and Drug Administration after severe adverse drug reactions (including 7 fatalities) were observed in patients who had been administered some lots of peginesatide formulations. Flow microscopy images of particle populations found in the peginesatide lots associated with severe adverse reactions in patients were readily distinguishable from images of particles in lots where severe adverse reactions did not occur. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

How to Read a Nutrition Facts Label

MedlinePlus Videos and Cool Tools

... label. These labels have a lot of important information — on fat and calories, serving sizes, sodium content, ... Nondiscrimination Visit the Nemours Web site. Note: All information on KidsHealth® is for educational purposes only. For ...

Development of Sintered Si3N4 for High Performance Thermomechanical Applications.

DTIC Science & Technology

1984-01-01

noted( 17) that final grain size of sintered Si3 N4 is quite sensitive to both temperature and time at temperature. The sintering of Si NI containing...Characterization of Ube-SN-E0 Si3 N4 Chemical Analysis Lot A-10 Lot A-18 N (alkali fusion) wt . % 38 38 0 (inert gas fusion) wt . % 1.2 1.4 C (inert gas fusion) wt ...temperature stutral applications except for the high creep rate, Which is of the ame order a NC-13. The sintering of -qfiN4ontaning 5 wt % LiAIq0 1and

Economic production quantity model for items with continuous quality characteristic, rework and reject

NASA Astrophysics Data System (ADS)

Tsou, Jia-Chi; Hejazi, Seyed Reza; Rasti Barzoki, Morteza

2012-12-01

The economic production quantity (EPQ) model is a well-known and commonly used inventory control technique. However, the model is built on an unrealistic assumption that all the produced items need to be of perfect quality. Having relaxed this assumption, some researchers have studied the effects of the imperfect products on the inventory control techniques. This article, thus, attempts to develop an EPQ model with continuous quality characteristic and rework. To this end, this study assumes that a produced item follows a general distribution pattern, with its quality being perfect, imperfect or defective. The analysis of the model developed indicates that there is an optimal lot size, which generates minimum total cost. Moreover, the results show that the optimal lot size of the model equals that of the classical EPQ model in case imperfect quality percentage is zero or even close to zero.

Clustered lot quality assurance sampling: a tool to monitor immunization coverage rapidly during a national yellow fever and polio vaccination campaign in Cameroon, May 2009.

PubMed

Pezzoli, L; Tchio, R; Dzossa, A D; Ndjomo, S; Takeu, A; Anya, B; Ticha, J; Ronveaux, O; Lewis, R F

2012-01-01

We used the clustered lot quality assurance sampling (clustered-LQAS) technique to identify districts with low immunization coverage and guide mop-up actions during the last 4 days of a combined oral polio vaccine (OPV) and yellow fever (YF) vaccination campaign conducted in Cameroon in May 2009. We monitored 17 pre-selected districts at risk for low coverage. We designed LQAS plans to reject districts with YF vaccination coverage <90% and with OPV coverage <95%. In each lot the sample size was 50 (five clusters of 10) with decision values of 3 for assessing OPV and 7 for YF coverage. We 'rejected' 10 districts for low YF coverage and 14 for low OPV coverage. Hence we recommended a 2-day extension of the campaign. Clustered-LQAS proved to be useful in guiding the campaign vaccination strategy before the completion of the operations.

Polyelectrolyte Bundles: Finite size at thermodynamic equilibrium?

NASA Astrophysics Data System (ADS)

Sayar, Mehmet

2005-03-01

Experimental observation of finite size aggregates formed by polyelectrolytes such as DNA and F-actin, as well as synthetic polymers like poly(p-phenylene), has created a lot of attention in recent years. Here, bundle formation in rigid rod-like polyelectrolytes is studied via computer simulations. For the case of hydrophobically modified polyelectrolytes finite size bundles are observed even in the presence of only monovalent counterions. Furthermore, in the absence of a hydrophobic backbone, we have also observed formation of finite size aggregates via multivalent counterion condensation. The size distribution of such aggregates and the stability is analyzed in this study.

7 CFR Exhibit J to Subpart A of... - Manufactured Home Sites, Rental Projects and Subdivisions: Development, Installation and Set-Up

Code of Federal Regulations, 2010 CFR

2010-01-01

... established frost line without exceeding the safe bearing capacity of the supporting soil. Set-Up. The work... architectural practices and shall provide for all utilities in a manner which allows adequate, economic, safe... residential environment which is an asset to the community in which it is located. 4. Lot Size. The size of...

Assessment of reproductive parameters in female Dwarf goat (Capra hircus) on the basis of progesterone profiles.

PubMed

Khanum, Shahnaz Adeeb; Hussain, Mujahid; Kausar, Rehana

2007-12-01

A study was undertaken to look into the reproductive performance of female Dwarf goats reared under traditional conditions at NIAB Farm, Faisalabad, Pakistan. The serum progesterone profile was used to monitor various reproductive parameters (length of postpartum period, resumption of cyclicity, gestation period, prepartum period, parturition) in two lots of goats. Litter size, birth weight of kids and kidding interval were also observed. Most of the animals conceived within 15-59 days of postpartum period. All the does conceived at first or second estrus. During gestation period, higher levels of progesterone were maintained with wide variations falling in the range of 3-13 ng ml(-1). However, a few days before parturition a decline was noticed at 6+/-0.9 days and it reached to the basal level of 0.1 ng ml(-1) after the completion of parturition process. The length of gestation period was found to be 145.8+/-5 days in the first lot and 145.2+/-4 days in the second lot. A very short kidding interval (203.7+/-46 days) and considerably bigger litter size (1.8+/-0.8) was observed. All the parturitions were normal and a considerable weight gain (8.2+/-0.3 kg) of mothers was recorded during pregnancy. The initial birth weight of kids was averaged as 2.1+/-0.5 kg in the first and 1.6+/-0.2 kg in the second lot. It was concluded that Dwarf goat has short gestation length, postpartum period and kidding interval along with multiple births being common. Due to these factors, its reproductive efficiency can be exploited for efficient goat meat production.

Models of determining deformations

NASA Astrophysics Data System (ADS)

Gladilin, V. N.

2016-12-01

In recent years, a lot of functions designed to determine deformation values that occur mostly as a result of settlement of structures and industrial equipment. Some authors suggest such advanced mathematical functions approximating deformations as general methods for the determination of deformations. The article describes models of deformations as physical processes. When comparing static, cinematic and dynamic models, it was found that the dynamic model reflects the deformation of structures and industrial equipment most reliably.

Cracks dynamics under tensional stress - a DEM approach

NASA Astrophysics Data System (ADS)

Debski, Wojciech; Klejment, Piotr; Kosmala, Alicja; Foltyn, Natalia; Szpindler, Maciej

2017-04-01

Breaking and fragmentation of solid materials is an extremely complex process involving scales ranging from an atomic scale (breaking inter-atomic bounds) up to thousands of kilometers in case of catastrophic earthquakes (in energy scale it ranges from single eV up to 1024 J). Such a large scale span of breaking processes opens lot of questions like, for example, scaling of breaking processes, existence of factors controlling final size of broken area, existence of precursors, dynamics of fragmentation, to name a few. The classical approach to study breaking process at seismological scales, i.e., physical processes in earthquake foci, is essentially based on two factors: seismic data (mostly) and the continuum mechanics (including the linear fracture mechanics). Such approach has been gratefully successful in developing kinematic (first) and dynamic (recently) models of seismic rupture and explaining many of earthquake features observed all around the globe. However, such approach will sooner or latter face a limitation due to a limited information content of seismic data and inherit limitations of the fracture mechanics principles. A way of avoiding this expected limitation is turning an attention towards a well established in physics method of computational simulations - a powerful branch of contemporary physics. In this presentation we discuss preliminary results of analysis of fracturing dynamics under external tensional forces using the Discrete Element Method approach. We demonstrate that even under a very simplified tensional conditions, the fragmentation dynamics is a very complex process, including multi-fracturing, spontaneous fracture generation and healing, etc. We also emphasis a role of material heterogeneity on the fragmentation process.

Aerosol Complexity and Implications for Predictability and Short-Term Forecasting

NASA Technical Reports Server (NTRS)

Colarco, Peter

2016-01-01

There are clear NWP and climate impacts from including aerosol radiative and cloud interactions. Changes in dynamics and cloud fields affect aerosol lifecycle, plume height, long-range transport, overall forcing of the climate system, etc. Inclusion of aerosols in NWP systems has benefit to surface field biases (e.g., T2m, U10m). Including aerosol affects has impact on analysis increments and can have statistically significant impacts on, e.g., tropical cyclogenesis. Above points are made especially with respect to aerosol radiative interactions, but aerosol-cloud interaction is a bigger signal on the global system. Many of these impacts are realized even in models with relatively simple (bulk) aerosol schemes (approx.10 -20 tracers). Simple schemes though imply simple representation of aerosol absorption and importantly for aerosol-cloud interaction particle-size distribution. Even so, more complex schemes exhibit a lot of diversity between different models, with issues such as size selection both for emitted particles and for modes. Prospects for complex sectional schemes to tune modal (and even bulk) schemes toward better selection of size representation. I think this is a ripe topic for more research -Systematic documentation of benefits of no vs. climatological vs. interactive (direct and then direct+indirect) aerosols. Document aerosol impact on analysis increments, inclusion in NWP data assimilation operator -Further refinement of baseline assumptions in model design (e.g., absorption, particle size distribution). Did not get into model resolution and interplay of other physical processes with aerosols (e.g., moist physics, obviously important), chemistry

New methodology for dynamic lot dispatching

NASA Astrophysics Data System (ADS)

Tai, Wei-Herng; Wang, Jiann-Kwang; Lin, Kuo-Cheng; Hsu, Yi-Chin

1994-09-01

This paper presents a new dynamic dispatching rule to improve delivery. The dynamic dispatching rule named `SLACK and OTD (on time delivery)' is developed for focusing on due date and target cycle time under the environment of IC manufacturing. This idea uses traditional SLACK policy to control long term due date and new OTD policy to reflect the short term stage queue time. Through the fuzzy theory, these two policies are combined as the dispatching controller to define the lot priority in the entire production line. Besides, the system would automatically update the lot priority according to the current line situation. Since the wafer dispatching used to be controlled by critical ratio that indicates the low customer satisfaction. And the overall slack time in the front end of the process is greater compared to that in the rear end of the process which reveals that the machines in the rear end are overloaded by rush orders. When SLACK and OTD are used the due date control has been gradually improved. The wafer with either a long stage queue time or urgent due date will be pushed through the overall production line instead of jammed in the front end. A demand pull system is also developed to satisfy not only due date but also the quantity of monthly demand. The SLACK and OTD rule has been implemented in Taiwan Semiconductor Manufacturing Company for eight months with beneficial results. In order to clearly monitor the SLACK and OTD policy, a method called box chart is generated to simulate the entire production system. From the box chart, we can not only monitor the result of decision policy but display the production situation on the density figure. The production cycle time and delivery situation can also be investigated.

7 CFR 989.104 - Lot.

Code of Federal Regulations, 2013 CFR

2013-01-01

... ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE RAISINS PRODUCED FROM GRAPES GROWN IN... form), processed in any continuous production of one calendar day and packaged in one size and style of... necessarily processed in one continuous production or during one calendar day, identifiable and offered for...

7 CFR 989.104 - Lot.

Code of Federal Regulations, 2014 CFR

2014-01-01

... ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE RAISINS PRODUCED FROM GRAPES GROWN IN... form), processed in any continuous production of one calendar day and packaged in one size and style of... necessarily processed in one continuous production or during one calendar day, identifiable and offered for...

7 CFR 989.104 - Lot.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE RAISINS PRODUCED FROM GRAPES GROWN IN... form), processed in any continuous production of one calendar day and packaged in one size and style of... necessarily processed in one continuous production or during one calendar day, identifiable and offered for...

Droplet-size distribution and stability of commercial injectable lipid emulsions containing fish oil.

PubMed

Gallegos, Críspulo; Valencia, Concepción; Partal, Pedro; Franco, José M; Maglio, Omay; Abrahamsson, Malin; Brito-de la Fuente, Edmundo

2012-08-01

The droplet size of commercial fish oil-containing injectable lipid emulsions, including conformance to United States Pharmacopeia (USP) standards on fat-globule size, was investigated. A total of 18 batches of three multichamber parenteral products containing the emulsion SMOFlipid as a component were analyzed. Samples from multiple lots of the products were evaluated to determine compliance with standards on the volume-weighted percentage of fat exceeding 0.05% (PFAT(5)) specified in USP chapter 729 to ensure the physical stability of i.v. lipid emulsions. The products were also analyzed to determine the effects of various storage times (3, 6, 9, and 12 months) and storage temperatures (25, 30, and 40 °C) on product stability. Larger-size lipid particles were quantified via single-particle optical sensing (SPOS). The emulsion's droplet-size distribution was determined via laser light scattering. SPOS and light-scattering analysis demonstrated mean PFAT(5) values well below USP-specified globule-size limits for all the tested products under all study conditions. In addition, emulsion aging at any storage temperature in the range studied did not result in a significant increase of PFAT(5) values, and mean droplet-size values did not change significantly during storage of up to 12 months at temperatures of 25-40 °C. PFAT(5) values were below the USP upper limits in SMOFlipid samples from multiple lots of three multichamber products after up to 12 months of storage at 25 or 30 °C or 6 months of storage at 40 °C.

Multidrug Resistance among New Tuberculosis Cases: Detecting Local Variation through Lot Quality-Assurance Sampling

PubMed Central

Lynn Hedt, Bethany; van Leth, Frank; Zignol, Matteo; Cobelens, Frank; van Gemert, Wayne; Viet Nhung, Nguyen; Lyepshina, Svitlana; Egwaga, Saidi; Cohen, Ted

2012-01-01

Background Current methodology for multidrug-resistant TB (MDR TB) surveys endorsed by the World Health Organization provides estimates of MDR TB prevalence among new cases at the national level. On the aggregate, local variation in the burden of MDR TB may be masked. This paper investigates the utility of applying lot quality-assurance sampling to identify geographic heterogeneity in the proportion of new cases with multidrug resistance. Methods We simulated the performance of lot quality-assurance sampling by applying these classification-based approaches to data collected in the most recent TB drug-resistance surveys in Ukraine, Vietnam, and Tanzania. We explored three classification systems—two-way static, three-way static, and three-way truncated sequential sampling—at two sets of thresholds: low MDR TB = 2%, high MDR TB = 10%, and low MDR TB = 5%, high MDR TB = 20%. Results The lot quality-assurance sampling systems identified local variability in the prevalence of multidrug resistance in both high-resistance (Ukraine) and low-resistance settings (Vietnam). In Tanzania, prevalence was uniformly low, and the lot quality-assurance sampling approach did not reveal variability. The three-way classification systems provide additional information, but sample sizes may not be obtainable in some settings. New rapid drug-sensitivity testing methods may allow truncated sequential sampling designs and early stopping within static designs, producing even greater efficiency gains. Conclusions Lot quality-assurance sampling study designs may offer an efficient approach for collecting critical information on local variability in the burden of multidrug-resistant TB. Before this methodology is adopted, programs must determine appropriate classification thresholds, the most useful classification system, and appropriate weighting if unbiased national estimates are also desired. PMID:22249242

Multidrug resistance among new tuberculosis cases: detecting local variation through lot quality-assurance sampling.

PubMed

Hedt, Bethany Lynn; van Leth, Frank; Zignol, Matteo; Cobelens, Frank; van Gemert, Wayne; Nhung, Nguyen Viet; Lyepshina, Svitlana; Egwaga, Saidi; Cohen, Ted

2012-03-01

Current methodology for multidrug-resistant tuberculosis (MDR TB) surveys endorsed by the World Health Organization provides estimates of MDR TB prevalence among new cases at the national level. On the aggregate, local variation in the burden of MDR TB may be masked. This paper investigates the utility of applying lot quality-assurance sampling to identify geographic heterogeneity in the proportion of new cases with multidrug resistance. We simulated the performance of lot quality-assurance sampling by applying these classification-based approaches to data collected in the most recent TB drug-resistance surveys in Ukraine, Vietnam, and Tanzania. We explored 3 classification systems- two-way static, three-way static, and three-way truncated sequential sampling-at 2 sets of thresholds: low MDR TB = 2%, high MDR TB = 10%, and low MDR TB = 5%, high MDR TB = 20%. The lot quality-assurance sampling systems identified local variability in the prevalence of multidrug resistance in both high-resistance (Ukraine) and low-resistance settings (Vietnam). In Tanzania, prevalence was uniformly low, and the lot quality-assurance sampling approach did not reveal variability. The three-way classification systems provide additional information, but sample sizes may not be obtainable in some settings. New rapid drug-sensitivity testing methods may allow truncated sequential sampling designs and early stopping within static designs, producing even greater efficiency gains. Lot quality-assurance sampling study designs may offer an efficient approach for collecting critical information on local variability in the burden of multidrug-resistant TB. Before this methodology is adopted, programs must determine appropriate classification thresholds, the most useful classification system, and appropriate weighting if unbiased national estimates are also desired.

Dynamic laser speckle applied to the analysis of maturation process of irradiated fresh fruits

NASA Astrophysics Data System (ADS)

Vincitorio, F. M.; Budini, N.; Freyre, C.; Mulone, C.; Fiorucci, M. P.; López, A. J.; Ramil, A.

2012-10-01

The treatment of fresh fruits with different doses of ionizing radiation has been found effective for delaying ripening and, in this way, to extend shelf life. This preservation method is likely to produce some functional or constitutive changes in the cellular structure of the fruit. In this work, a test of the effectiveness of fruit irradiation with relatively low doses was performed by using dynamic speckle imaging. Bananas from a same lot were chosen, being a first series of them irradiated with different doses of 0.2, 0.4 and 0.6 kGy (Gy = J/kg) and a second series with doses of 0.2, 0.4, 0.6 and 1 kGy. Non irradiated bananas (0 kGy) were considered as the lot reference for contrast. Irradiation was carried out at the Semi-Industrial Cobalt 60 facility of the Ezeiza Atomic Center, with an activity of 6 × 105 Curie and a dose rate of 28.5 Gy/min. The objective of this work is to analyze differences in the maturation process between irradiated and nonirradiated fruits by means of dynamic speckle pattern evaluation.

Allogeneic Cell Therapy Bioprocess Economics and Optimization: Single-Use Cell Expansion Technologies

PubMed Central

Simaria, Ana S; Hassan, Sally; Varadaraju, Hemanthram; Rowley, Jon; Warren, Kim; Vanek, Philip; Farid, Suzanne S

2014-01-01

For allogeneic cell therapies to reach their therapeutic potential, challenges related to achieving scalable and robust manufacturing processes will need to be addressed. A particular challenge is producing lot-sizes capable of meeting commercial demands of up to 109 cells/dose for large patient numbers due to the current limitations of expansion technologies. This article describes the application of a decisional tool to identify the most cost-effective expansion technologies for different scales of production as well as current gaps in the technology capabilities for allogeneic cell therapy manufacture. The tool integrates bioprocess economics with optimization to assess the economic competitiveness of planar and microcarrier-based cell expansion technologies. Visualization methods were used to identify the production scales where planar technologies will cease to be cost-effective and where microcarrier-based bioreactors become the only option. The tool outputs also predict that for the industry to be sustainable for high demand scenarios, significant increases will likely be needed in the performance capabilities of microcarrier-based systems. These data are presented using a technology S-curve as well as windows of operation to identify the combination of cell productivities and scale of single-use bioreactors required to meet future lot sizes. The modeling insights can be used to identify where future R&D investment should be focused to improve the performance of the most promising technologies so that they become a robust and scalable option that enables the cell therapy industry reach commercially relevant lot sizes. The tool outputs can facilitate decision-making very early on in development and be used to predict, and better manage, the risk of process changes needed as products proceed through the development pathway. Biotechnol. Bioeng. 2014;111: 69–83. © 2013 Wiley Periodicals, Inc. PMID:23893544

Allogeneic cell therapy bioprocess economics and optimization: single-use cell expansion technologies.

PubMed

Simaria, Ana S; Hassan, Sally; Varadaraju, Hemanthram; Rowley, Jon; Warren, Kim; Vanek, Philip; Farid, Suzanne S

2014-01-01

For allogeneic cell therapies to reach their therapeutic potential, challenges related to achieving scalable and robust manufacturing processes will need to be addressed. A particular challenge is producing lot-sizes capable of meeting commercial demands of up to 10(9) cells/dose for large patient numbers due to the current limitations of expansion technologies. This article describes the application of a decisional tool to identify the most cost-effective expansion technologies for different scales of production as well as current gaps in the technology capabilities for allogeneic cell therapy manufacture. The tool integrates bioprocess economics with optimization to assess the economic competitiveness of planar and microcarrier-based cell expansion technologies. Visualization methods were used to identify the production scales where planar technologies will cease to be cost-effective and where microcarrier-based bioreactors become the only option. The tool outputs also predict that for the industry to be sustainable for high demand scenarios, significant increases will likely be needed in the performance capabilities of microcarrier-based systems. These data are presented using a technology S-curve as well as windows of operation to identify the combination of cell productivities and scale of single-use bioreactors required to meet future lot sizes. The modeling insights can be used to identify where future R&D investment should be focused to improve the performance of the most promising technologies so that they become a robust and scalable option that enables the cell therapy industry reach commercially relevant lot sizes. The tool outputs can facilitate decision-making very early on in development and be used to predict, and better manage, the risk of process changes needed as products proceed through the development pathway. © 2013 Wiley Periodicals, Inc.

[Dynamic changes of urban architecture landscape based on Barista: a case study in Tiexi District of Shenyang City].

PubMed

Zhang, Pei-feng; Hu, Yuan-man; He, Hong-shi; Xiong, Zai-ping; Liu, Miao

2010-12-01

In this paper, three-dimensional building information was extracted from high resolution satellite image based on Barista software. Combined with ArcGIS software, the dynamic changes of the building landscape in Tiexi District of Shenyang City during urban renewal process were analyzed from the conversion contribution rate, building density, average building height, and built-up area rate. It was found that during this urban renewal process, four dominant landscape types (vacant lot, residential building, industrial building, and road) were the main parts of the landscape changes. The areas of vacant lot, residential building, commercial building, and road increased, while that of industrial building decreased. The building density decreased, while the average building height increased. There was an obvious regional variation in building landscape. The building density in industrial district was higher than that in residential district, while the average building height was in adverse. The further from the city center, the lower the building density and building average height.

Models and Measurements for Multi-Layer Displays

DTIC Science & Technology

2006-07-26

measurements. The observed statistical variation in the data results from laser speckle. No systematic uncertainties, which are expected to be less...difference metric. There are also some powerful statistical techniques to deal with this type of experiment, although it would take a lot of time to...hTraceWidth,vTraceWidth] in 10s of micrometers % Transitor sixe is vector : [hTransistorSize,vTransistorSize] in 10s of micrometers %Image is plotted if

The effects of substrate size, surface area, and density on coat thickness of multi-particulate dosage forms.

PubMed

Heinicke, Grant; Matthews, Frank; Schwartz, Joseph B

2005-01-01

Drugs layering experiments were performed in a fluid bed fitted with a rotor granulator insert using diltiazem as a model drug. The drug was applied in various quantities to sugar spheres of different mesh sizes to give a series of drug-layered sugar spheres (cores) of different potency, size, and weight per particle. The drug presence lowered the bulk density of the cores in proportion to the quantity of added drug. Polymer coating of each core lot was performed in a fluid bed fitted with a Wurster insert. A series of polymer-coated cores (pellets) was removed from each coating experiment. The mean diameter of each core and each pellet sample was determined by image analysis. The rate of change of diameter on polymer addition was determined for each starting size of core and compared to calculated values. The core diameter was displaced from the line of best fit through the pellet diameter data. Cores of different potency with the same size distribution were made by layering increasing quantities of drug onto sugar spheres of decreasing mesh size. Equal quantities of polymer were applied to the same-sized core lots and coat thickness was measured. Weight/weight calculations predict equal coat thickness under these conditions, but measurable differences were found. Simple corrections to core charge weight in the Wurster insert were successfully used to manufacture pellets having the same coat thickness. The sensitivity of the image analysis technique in measuring particle size distributions (PSDs) was demonstrated by measuring a displacement in PSD after addition of 0.5% w/w talc to a pellet sample.

A Decision-making Model for a Two-stage Production-delivery System in SCM Environment

NASA Astrophysics Data System (ADS)

Feng, Ding-Zhong; Yamashiro, Mitsuo

A decision-making model is developed for an optimal production policy in a two-stage production-delivery system that incorporates a fixed quantity supply of finished goods to a buyer at a fixed interval of time. First, a general cost model is formulated considering both supplier (of raw materials) and buyer (of finished products) sides. Then an optimal solution to the problem is derived on basis of the cost model. Using the proposed model and its optimal solution, one can determine optimal production lot size for each stage, optimal number of transportation for semi-finished goods, and optimal quantity of semi-finished goods transported each time to meet the lumpy demand of consumers. Also, we examine the sensitivity of raw materials ordering and production lot size to changes in ordering cost, transportation cost and manufacturing setup cost. A pragmatic computation approach for operational situations is proposed to solve integer approximation solution. Finally, we give some numerical examples.

A hybrid credibility-based fuzzy multiple objective optimisation to differential pricing and inventory policies with arbitrage consideration

NASA Astrophysics Data System (ADS)

Ghasemy Yaghin, R.; Fatemi Ghomi, S. M. T.; Torabi, S. A.

2015-10-01

In most markets, price differentiation mechanisms enable manufacturers to offer different prices for their products or services in different customer segments; however, the perfect price discrimination is usually impossible for manufacturers. The importance of accounting for uncertainty in such environments spurs an interest to develop appropriate decision-making tools to deal with uncertain and ill-defined parameters in joint pricing and lot-sizing problems. This paper proposes a hybrid bi-objective credibility-based fuzzy optimisation model including both quantitative and qualitative objectives to cope with these issues. Taking marketing and lot-sizing decisions into account simultaneously, the model aims to maximise the total profit of manufacturer and to improve service aspects of retailing simultaneously to set different prices with arbitrage consideration. After applying appropriate strategies to defuzzify the original model, the resulting non-linear multi-objective crisp model is then solved by a fuzzy goal programming method. An efficient stochastic search procedure using particle swarm optimisation is also proposed to solve the non-linear crisp model.

Sampling, testing and modeling particle size distribution in urban catch basins.

PubMed

Garofalo, G; Carbone, M; Piro, P

2014-01-01

The study analyzed the particle size distribution of particulate matter (PM) retained in two catch basins located, respectively, near a parking lot and a traffic intersection with common high levels of traffic activity. Also, the treatment performance of a filter medium was evaluated by laboratory testing. The experimental treatment results and the field data were then used as inputs to a numerical model which described on a qualitative basis the hydrological response of the two catchments draining into each catch basin, respectively, and the quality of treatment provided by the filter during the measured rainfall. The results show that PM concentrations were on average around 300 mg/L (parking lot site) and 400 mg/L (road site) for the 10 rainfall-runoff events observed. PM with a particle diameter of <45 μm represented 40-50% of the total PM mass. The numerical model showed that a catch basin with a filter unit can remove 30 to 40% of the PM load depending on the storm characteristics.

Geometry and material choices govern hard-rock drilling performance of PDC drag cutters.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wise, Jack LeRoy

2005-06-01

Sandia National Laboratories has partnered with industry on a multifaceted, baseline experimental study that supports the development of improved drag cutters for advanced drill bits. Different nonstandard cutter lots were produced and subjected to laboratory tests that evaluated the influence of selected design and processing parameters on cutter loads, wear, and durability pertinent to the penetration of hard rock with mechanical properties representative of formations encountered in geothermal or deep oil/gas drilling environments. The focus was on cutters incorporating ultrahard PDC (polycrystalline diamond compact) overlays (i.e., diamond tables) on tungsten-carbide substrates. Parameter variations included changes in cutter geometry, material composition,more » and processing conditions. Geometric variables were the diamond-table thickness, the cutting-edge profile, and the PDC/substrate interface configuration. Material and processing variables for the diamond table were, respectively, the diamond particle size and the sintering pressure applied during cutter fabrication. Complementary drop-impact, granite-log abrasion, linear cutting-force, and rotary-drilling tests examined the response of cutters from each lot. Substantial changes in behavior were observed from lot to lot, allowing the identification of features contributing major (factor of 10+) improvements in cutting performance for hard-rock applications. Recent field demonstrations highlight the advantages of employing enhanced cutter technology during challenging drilling operations.« less

Allogeneic cell therapy bioprocess economics and optimization: downstream processing decisions.

PubMed

Hassan, Sally; Simaria, Ana S; Varadaraju, Hemanthram; Gupta, Siddharth; Warren, Kim; Farid, Suzanne S

2015-01-01

To develop a decisional tool to identify the most cost effective process flowsheets for allogeneic cell therapies across a range of production scales. A bioprocess economics and optimization tool was built to assess competing cell expansion and downstream processing (DSP) technologies. Tangential flow filtration was generally more cost-effective for the lower cells/lot achieved in planar technologies and fluidized bed centrifugation became the only feasible option for handling large bioreactor outputs. DSP bottlenecks were observed at large commercial lot sizes requiring multiple large bioreactors. The DSP contribution to the cost of goods/dose ranged between 20-55%, and 50-80% for planar and bioreactor flowsheets, respectively. This analysis can facilitate early decision-making during process development.

Method for selecting hollow microspheres for use in laser fusion targets

DOEpatents

Farnum, Eugene H.; Fries, R. Jay; Havenhill, Jerry W.; Smith, Maurice Lee; Stoltz, Daniel L.

1976-01-01

Hollow microspheres having thin and very uniform wall thickness are useful as containers for the deuterium and tritium gas mixture used as a fuel in laser fusion targets. Hollow microspheres are commercially available; however, in commercial lots only a very small number meet the rigid requirements for use in laser fusion targets. Those meeting these requirements may be separated from the unsuitable ones by subjecting the commercial lot to size and density separations and then by subjecting those hollow microspheres thus separated to an external pressurization at which those which are aspherical or which have nonuniform walls are broken and separating the sound hollow microspheres from the broken ones.

The Evolution of Economist's Labour Market in Romania

ERIC Educational Resources Information Center

Isaic-Maniu, Alexandru; Herteliu, Claudiu

2006-01-01

The modern world is undergoing a fundamental transformation characterized by a lot of challenges, dynamism, globalization, and the increasing influence of Information and Communication Technologies (ICTs). These new technologies have implications for all aspects of the society and economy; they are changing the way of doing business, the way of…

Lot quality assurance sampling techniques in health surveys in developing countries: advantages and current constraints.

PubMed

Lanata, C F; Black, R E

1991-01-01

Traditional survey methods, which are generally costly and time-consuming, usually provide information at the regional or national level only. The utilization of lot quality assurance sampling (LQAS) methodology, developed in industry for quality control, makes it possible to use small sample sizes when conducting surveys in small geographical or population-based areas (lots). This article describes the practical use of LQAS for conducting health surveys to monitor health programmes in developing countries. Following a brief description of the method, the article explains how to build a sample frame and conduct the sampling to apply LQAS under field conditions. A detailed description of the procedure for selecting a sampling unit to monitor the health programme and a sample size is given. The sampling schemes utilizing LQAS applicable to health surveys, such as simple- and double-sampling schemes, are discussed. The interpretation of the survey results and the planning of subsequent rounds of LQAS surveys are also discussed. When describing the applicability of LQAS in health surveys in developing countries, the article considers current limitations for its use by health planners in charge of health programmes, and suggests ways to overcome these limitations through future research. It is hoped that with increasing attention being given to industrial sampling plans in general, and LQAS in particular, their utilization to monitor health programmes will provide health planners in developing countries with powerful techniques to help them achieve their health programme targets.

24 CFR 1710.107 - Risks of buying land.

Code of Federal Regulations, 2011 CFR

2011-04-01

... own sales program and local real estate brokers may not be interested in listing your lot. (4) Any subdivision will have an impact on the surrounding environment. Whether or not the impact is adverse and the degree of impact, will depend on the location, size, planning and extent of development. Subdivisions...

Rain Garden Research at EPA's Urban Watershed Research Facility

EPA Science Inventory

I have been invited to give a presentation at the 2009 National Erosion Conference in Hartford, CT, on October 27-28, 2009. My presentation discusses the research on sizing of rain gardens that is being conducted using the large, parking lot rain gardens on-site. I discuss the ...

7 CFR 51.1440 - Application of standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS) United States Standards for Grades of Shelled Pecans Application of Standards § 51.1440 Application of standards. The grade of a lot of shelled pecans shall be determined on the basis of a composite... container or number of containers in which the pecans are obviously of a quality or size materially...

Urban Runoff and Nutrients Loading Control from Sustainable BMPs (Invited)

NASA Astrophysics Data System (ADS)

Xiao, Q.

2009-12-01

Climate change alters hydrodynamic and nutrient dynamic in both large and small geographic scales. These changes in our freshwater system directly affect drinking water, food production, business, and all aspects of our life. Along with climate change is increasing urbanization which alters natural landscape. Urban runoff has been identified as one of many potential drivers of the decline of pelagic fishes in san Francisco Bay-Delta region. Recent found of Pyrethroids in American River has increased scientists, public, and policy makers’ concern about our fresh water system. Increasing our understanding about the fundamental hydrodynamic, nutrient dynamics, and the transport mechanics of runoff and nutrients are important for future water resource and ecosystem management. Urbanization has resulted in significantly increasing the amount of impervious land cover. Most impervious land covers are hydrophobic that alters surface runoff because of the effects on surface retention storage, rainfall interception, and infiltration. Large volumes of excess storm runoff from urbanized areas cause flooding, water pollution, groundwater recharge deficits, destroyed habitat, beach closures, and toxicity to aquatic organisms. Parking lot alone accounts for more than 11% of these impervious surfaces. Contrast to impervious parking lot, turfgrass can accouter for 12% of urban land in California. Irrigated urban landscapes create considerable benefits to our daily living. However, the use of fertilizers and pesticides has caused environmental problems. Preventing fertilizers and pesticides from entering storm drains is an important goal for both landscape and storm runoff managers. Studies of urban runoff have found that the most fertilizers and pesticides are from dry weather runoff which conveys pollutants to sidewalks, streets, and storm drains. Controlling surface runoff is critical to preventing these pollutants from entering storm drains and water bodies. Large scale construction of runoff retention basins and treatment facilities to meet TMDL (Total Maximum Daily Load) regulations are not cost-effective or practical. An alternative approach is to control runoff and nutrients on-site through installation of decentralized BMPs that detain and infiltrate runoff before it reaches storm drains. Recent developed green-infrastructure which integrating engineered soil and trees to reduce runoff and nutrients loading is a self-sustained best management practice (BMP). This BMP has been testing and used in urban runoff control. In Davis, CA this type of BMPs were installed in a parking lot and a residential property to evaluate the system’s effectiveness on reducing storm runoff and pollutant loading from the parking lot and irrigated landscape. Storm runoff and pollutant loading were measured and monitored during February 2007 thru May 2009 from the parking lot. The BMP reduced surface runoff and nutrients by 88.8% and 95.3%, respectively. In the residential irrigated landscape, the dry-weather runoff was monitored during 2007 irrigation season, the BMP captured almost all dry weather runoff. The performance of these BMPs demonstrated their potential use for reducing runoff and nutrients loading. Control urban runoff from these 23% landscape (i.e., parking lot and irrigated turf grass) could largely alter the runoff and nutrients transport and their dynamic in our water system.

Optimal pricing and lot-sizing for perishable inventory with price and time dependent ramp-type demand

NASA Astrophysics Data System (ADS)

Panda, S.; Saha, S.; Basu, M.

2013-01-01

Product perishability is an important aspect of inventory control. To minimise the effect of deterioration, retailers in supermarkets, departmental store managers, etc. always want higher inventory depletion rate. In this article, we propose a dynamic pre- and post-deterioration cumulative discount policy to enhance inventory depletion rate resulting low volume of deterioration cost, holding cost and hence higher profit. It is assumed that demand is a price and time dependent ramp-type function and the product starts to deteriorate after certain amount of time. Unlike the conventional inventory models with pricing strategies, which are restricted to a fixed number of price changes and to a fixed cycle length, we allow the number of price changes before as well as after the start of deterioration and the replenishment cycle length to be the decision variables. Before start of deterioration, discounts on unit selling price are provided cumulatively in successive pricing cycles. After the start of deterioration, discounts on reduced unit selling price are also provided in a cumulative way. A mathematical model is developed and the existence of the optimal solution is verified. A numerical example is presented, which indicates that under the cumulative effect of price discounting, dynamic pricing policy outperforms static pricing strategy. Sensitivity analysis of the model is carried out.

Dynamic Factorization in Large-Scale Optimization

DTIC Science & Technology

1989-06-01

side column and the botton (cost) ro . Because of the symmetric nature of the mutual primal-dual nijethod. a sensii 1 approacd s to al’ocal, a sinle...denimonstrates strong numnrical statii’, aw x, l l ii at,, r ,parsity of {" Several nw’tlhods have been proposed (Bartels and Golub [1969], Forrest and Tom...formerly) disjoint components which have been merged by the change in the representation of the dynamic singletons, 130 10 Q’ Q9 U> C) lt lot 001 0

Dynamic Stall Computations Using a Zonal Navier-Stokes Model

DTIC Science & Technology

1988-06-01

NAVAL POSTGRADUATE SCHOOL lotMonterey ,California CD Lj STATF ,-S THESIS DYNAMIC STALL CALCULATIONS USING A ZONAL.-,_ % 0 NVETESISDE by Jack H...Conroyd, Jr. June 1988 Thesis Co-advisors: M.F. Platzer Lawrence W. Carr Approved for public release; distribution is unlimitedDOTIC , ~~~~~~~~ELECT...OINT %, Master s Thesis OM To June 212 6 SLP;’LEENTARY NOTATION ri The views expressed in this thesis are those of the author and do not reflect the

Size effects of nano-spaced basal stacking faults on the strength and deformation mechanisms of nanocrystalline pure hcp metals

NASA Astrophysics Data System (ADS)

Wang, Wen; Jiang, Ping; Yuan, Fuping; Wu, Xiaolei

2018-05-01

The size effects of nano-spaced basal stacking faults (SFs) on the tensile strength and deformation mechanisms of nanocrystalline pure cobalt and magnesium have been investigated by a series of large-scale 2D columnar and 3D molecular dynamics simulations. Unlike the strengthening effect of basal SFs on Mg alloys, the nano-spaced basal SFs are observed to have no strengthening effect on the nanocrystalline pure cobalt and magnesium from MD simulations. These observations could be attributed to the following two reasons: (i) Lots of new basal SFs are formed before (for cobalt) or simultaneously with (for magnesium) the other deformation mechanisms (i.e. the formation of twins and the < c + a > edge dislocations) during the tensile deformation; (ii) In hcp alloys, the segregation of alloy elements and impurities at typical interfaces, such as SFs, can stablilise them for enhancing the interactions with dislocation and thus elevating the strength. Without such segregation in pure hcp metals, the < c + a > edge dislocations can cut through the basal SFs although the interactions between the < c + a > dislocations and the pre-existing SFs/newly formed SFs are observed. The nano-spaced basal SFs are also found to have no restriction effect on the formation of deformation twins.

Properties of Ferroelectric Perovskite Structures under Non-equilibrium Conditions

NASA Astrophysics Data System (ADS)

Zhang, Qingteng

Ferroelectric materials have received lots of attention thanks to their intriguing properties such as the piezoelectric and pyroelectric effects, as well as the large dielectric constants and the spontaneous polarization which can potentially be used for information storage. In particular, perovskite crystal has a very simple unit cell structure yet a very rich phase transition diagram, which makes it one of the most intensively studied ferroelectric materials. In this dissertation, we use effective Hamiltonian, a first-principles-based computational technique to study the finite-temperature properties of ferroelectric perovskites. We studied temperature-graded (BaxSr 1-x)TiO3 (BST) bulk alloys as well as the dynamics of nanodomain walls (nanowalls) in Pb(Zr xTi1-x)O 3 (PZT) ultra-thin films under the driving force of an AC field. Our computations suggest that, for the temperature-graded BST, the polarization responds to the temperature gradient (TG), with the "up" and "down" offset observed in polarization components along the direction of TG, in agreement with the findings from experiments. For the nanowalls in PZT, the dynamics can be described by the damped-harmonic-oscillator model, and we observed a size-driven transition from resonance to relaxational dynamics at a critical thickness of 7.2 nm. The transition originates from the change in the effective mass of a nanowall as a film thickness increases. Some of the findings may find potential applications in various devices, such as thermal sensors, energy converters, or novel memory units.

Residential Consumption Scheduling Based on Dynamic User Profiling

NASA Astrophysics Data System (ADS)

Mangiatordi, Federica; Pallotti, Emiliano; Del Vecchio, Paolo; Capodiferro, Licia

Deployment of household appliances and of electric vehicles raises the electricity demand in the residential areas and the impact of the building's electrical power. The variations of electricity consumption across the day, may affect both the design of the electrical generation facilities and the electricity bill, mainly when a dynamic pricing is applied. This paper focuses on an energy management system able to control the day-ahead electricity demand in a residential area, taking into account both the variability of the energy production costs and the profiling of the users. The user's behavior is dynamically profiled on the basis of the tasks performed during the previous days and of the tasks foreseen for the current day. Depending on the size and on the flexibility in time of the user tasks, home inhabitants are grouped in, one over N, energy profiles, using a k-means algorithm. For a fixed energy generation cost, each energy profile is associated to a different hourly energy cost. The goal is to identify any bad user profile and to make it pay a highest bill. A bad profile example is when a user applies a lot of consumption tasks and low flexibility in task reallocation time. The proposed energy management system automatically schedules the tasks, solving a multi-objective optimization problem based on an MPSO strategy. The goals, when identifying bad users profiles, are to reduce the peak to average ratio in energy demand, and to minimize the energy costs, promoting virtuous behaviors.

Characterizing the size distribution of particles in urban stormwater by use of fixed-point sample-collection methods

USGS Publications Warehouse

Selbig, William R.; Bannerman, Roger T.

2011-01-01

The U.S Geological Survey, in cooperation with the Wisconsin Department of Natural Resources (WDNR) and in collaboration with the Root River Municipal Stormwater Permit Group monitored eight urban source areas representing six types of source areas in or near Madison, Wis. in an effort to improve characterization of particle-size distributions in urban stormwater by use of fixed-point sample collection methods. The types of source areas were parking lot, feeder street, collector street, arterial street, rooftop, and mixed use. This information can then be used by environmental managers and engineers when selecting the most appropriate control devices for the removal of solids from urban stormwater. Mixed-use and parking-lot study areas had the lowest median particle sizes (42 and 54 (u or mu)m, respectively), followed by the collector street study area (70 (u or mu)m). Both arterial street and institutional roof study areas had similar median particle sizes of approximately 95 (u or mu)m. Finally, the feeder street study area showed the largest median particle size of nearly 200 (u or mu)m. Median particle sizes measured as part of this study were somewhat comparable to those reported in previous studies from similar source areas. The majority of particle mass in four out of six source areas was silt and clay particles that are less than 32 (u or mu)m in size. Distributions of particles ranging from 500 (u or mu)m were highly variable both within and between source areas. Results of this study suggest substantial variability in data can inhibit the development of a single particle-size distribution that is representative of stormwater runoff generated from a single source area or land use. Continued development of improved sample collection methods, such as the depth-integrated sample arm, may reduce variability in particle-size distributions by mitigating the effect of sediment bias inherent with a fixed-point sampler.

The Audit of the Information Technologies & Communication Projects Developed by Students

ERIC Educational Resources Information Center

Capisizu, Sergiu; Nosca, Gheorghe; Parlog, Adriean

2006-01-01

The modern world is undergoing a fundamental transformation characterized by a lot of challenges, dynamism, globalization, and the increasing influence of Information and Communication Technologies (ICTs). These new technologies have implications for all aspects of the society and economy; they are changing the way of doing business, the way of…

A Comparative Study of Learning Curve Models in Defense Airframe Cost Estimating

DTIC Science & Technology

2015-03-26

production history and availability of relevant airframe costs. F-15 airframe costs were discovered in two data bases. The F-15 A-D airframe lot...an assembly line at Ford or Toyota . Given this dynamic, assuming the real incompressibility factor is somewhere between 0.0 and 0.1 is not

7 CFR 361.5 - Sampling of seeds.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Sampling of seeds. 361.5 Section 361.5 Agriculture..., DEPARTMENT OF AGRICULTURE IMPORTATION OF SEED AND SCREENINGS UNDER THE FEDERAL SEED ACT § 361.5 Sampling of... section. (3) The maximum sizes of lots of each kind of seed allowed entry without sampling for sowing for...

7 CFR 993.104 - Lot.

Code of Federal Regulations, 2011 CFR

2011-01-01

... means any quantity of prunes delivered by one producer or one dehydrator to a handler on which... 30 “ton box” containers or (2), if in other containers, not more than 60,000 pounds of prunes. If the... production of one calendar day and packed during such day in one size and style of container or (ii) the...

7 CFR 993.104 - Lot.

Code of Federal Regulations, 2014 CFR

2014-01-01

... means any quantity of prunes delivered by one producer or one dehydrator to a handler on which... 30 “ton box” containers or (2), if in other containers, not more than 60,000 pounds of prunes. If the... production of one calendar day and packed during such day in one size and style of container or (ii) the...

7 CFR 993.104 - Lot.

Code of Federal Regulations, 2012 CFR

2012-01-01

... means any quantity of prunes delivered by one producer or one dehydrator to a handler on which... 30 “ton box” containers or (2), if in other containers, not more than 60,000 pounds of prunes. If the... production of one calendar day and packed during such day in one size and style of container or (ii) the...

36 CFR 28.12 - Development standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... significant harm to the natural resources of the Seashore. (c) Minimum lot size is 4,000 square feet. A.../FEMA shown on Flood Insurance Rate Maps for Fire Island communities. (g) A swimming pool is an... hazards and/or detract from the natural or cultural scene. (j) A zoning authority shall have in place...

7 CFR 70.105 - Procedures for appeal gradings.

Code of Federal Regulations, 2011 CFR

2011-01-01

... PRODUCTS AND RABBIT PRODUCTS Grading of Poultry Products and Rabbit Products Appeal of A Grading Or... sample size for the lot shall consist of double the samples required in § 70.80. (c) Poultry or rabbits... is performed. (d) Overwraps on frozen poultry or rabbits shall be removed from all birds or rabbits...

7 CFR 91.10 - Information required in connection with an application.

Code of Federal Regulations, 2013 CFR

2013-01-01

... requested, and the size of the sample. In addition, information regarding analysis of the lot by any federal... 7 Agriculture 3 2013-01-01 2013-01-01 false Information required in connection with an application...) COMMODITY LABORATORY TESTING PROGRAMS SERVICES AND GENERAL INFORMATION Application for Services § 91.10...

Determination of optimal lot size and production rate for multi-production channels with limited capacity

NASA Astrophysics Data System (ADS)

Huang, Yeu-Shiang; Wang, Ruei-Pei; Ho, Jyh-Wen

2015-07-01

Due to the constantly changing business environment, producers often have to deal with customers by adopting different procurement policies. That is, manufacturers confront not only predictable and regular orders, but also unpredictable and irregular orders. In this study, from the perspective of upstream manufacturers, both regular and irregular orders are considered in coping with the situation in which an uncertain demand is faced by the manufacturer, and a capacity confirming mechanism is used to examine such demand. If the demand is less than or equal to the capacity of the ordinary production channel, the general supply channel is utilised to fully account for the manufacturing process, but if the demand is greater than the capacity of the ordinary production channel, the contingency production channel would be activated along with the ordinary channel to satisfy the upcoming high demand. Besides, the reproductive property of the probability distribution is employed to represent the order quantity of the two types of demand. Accordingly, the optimal production rates and lot sizes for both channels are derived to provide managers with insights for further production planning.

A joint economic lot-sizing problem with fuzzy demand, defective items and environmental impacts

NASA Astrophysics Data System (ADS)

Jauhari, W. A.; Laksono, P. W.

2017-11-01

In this paper, a joint economic lot-sizing problem consisting of a vendor and a buyer was proposed. A buyer ordered products from a vendor to fulfill end customer’s demand. A produced a batch of products, and delivered it to the buyer. The production process in the vendor was imperfect and produced a number of defective products. Production rate was assumed to be adjustable to control the output of vendor’s production. A continuous review policy was adopted by the buyer to manage his inventory level. In addition, an average annual demand was considered to be fuzzy rather than constant. The proposed model contributed to the current inventory literature by allowing the inclusion of fuzzy annual demand, imperfect production emission cost, and adjustable production rate. The proposed model also considered carbon emission cost which was resulted from the transportation activity. A mathematical model was developed for obtaining the optimal ordering quantity, safety factor and the number of deliveries so the joint total cost was minimized. Furthermore, an iterative procedure was suggested to determine the optimal solutions.

Multi-Objective Programming for Lot-Sizing with Quantity Discount

NASA Astrophysics Data System (ADS)

Kang, He-Yau; Lee, Amy H. I.; Lai, Chun-Mei; Kang, Mei-Sung

2011-11-01

Multi-objective programming (MOP) is one of the popular methods for decision making in a complex environment. In a MOP, decision makers try to optimize two or more objectives simultaneously under various constraints. A complete optimal solution seldom exists, and a Pareto-optimal solution is usually used. Some methods, such as the weighting method which assigns priorities to the objectives and sets aspiration levels for the objectives, are used to derive a compromise solution. The ɛ-constraint method is a modified weight method. One of the objective functions is optimized while the other objective functions are treated as constraints and are incorporated in the constraint part of the model. This research considers a stochastic lot-sizing problem with multi-suppliers and quantity discounts. The model is transformed into a mixed integer programming (MIP) model next based on the ɛ-constraint method. An illustrative example is used to illustrate the practicality of the proposed model. The results demonstrate that the model is an effective and accurate tool for determining the replenishment of a manufacturer from multiple suppliers for multi-periods.

LX-17-1 Stockpile Returned Material Lot Comparison

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gagliardi, F.; Pease, S.; Willey, T.

2015-02-18

Many different lots of LX-17 have been produced over the years. Two varieties of LX-17, LX-17-0 and LX-17-1, have at one point or another been a part of the Livermore stockpile systems. LX-17-0 was made with dry-aminated TATB whereas LX-17-1 was made with wet-aminated TATB. Both versions have the same TATB to Kel-F 800 mass ratio of 92.5%/7.5%. Both kinds of LX-17 were formulated at Holston during the late 1970s or early to mid-1980s and were certified to have met the necessary specifications that cover the purity, particle size range, explosive to binder ratio, etc. In recent years, Trevor Willymore » and others have performed a detailed evaluation of solid parts made from each of the LX-17 lots manufactured at Holston. Using the Advanced Light Source at LBNL, Willey and his colleagues radiographed many samples from isostatic pressings using the same scanning conditions. In their investigation they identified that even though the bulk composition can be the same, there may exist a large spread in how smoothly the TATB and binder were distributed within the radiographed volume of different lots of material.1 Overall, the dry-aminated TATB-based material, LX-17-0, had a smooth TATB and binder distribution, whereas the wet-aminated TATB-based LX-17-1 showed a wide range of binder distributions. The results for five different LX-17-1 lots are shown in Figure 1. The wide variation in material distribution has raised the question about whether or not this sort variability will cause significant differences in mechanical behavior.« less

Clustered lot quality assurance sampling to assess immunisation coverage: increasing rapidity and maintaining precision.

PubMed

Pezzoli, Lorenzo; Andrews, Nick; Ronveaux, Olivier

2010-05-01

Vaccination programmes targeting disease elimination aim to achieve very high coverage levels (e.g. 95%). We calculated the precision of different clustered lot quality assurance sampling (LQAS) designs in computer-simulated surveys to provide local health officers in the field with preset LQAS plans to simply and rapidly assess programmes with high coverage targets. We calculated sample size (N), decision value (d) and misclassification errors (alpha and beta) of several LQAS plans by running 10 000 simulations. We kept the upper coverage threshold (UT) at 90% or 95% and decreased the lower threshold (LT) progressively by 5%. We measured the proportion of simulations with < or =d individuals unvaccinated or lower if the coverage was set at the UT (pUT) to calculate beta (1-pUT) and the proportion of simulations with >d unvaccinated individuals if the coverage was LT% (pLT) to calculate alpha (1-pLT). We divided N in clusters (between 5 and 10) and recalculated the errors hypothesising that the coverage would vary in the clusters according to a binomial distribution with preset standard deviations of 0.05 and 0.1 from the mean lot coverage. We selected the plans fulfilling these criteria: alpha < or = 5% beta < or = 20% in the unclustered design; alpha < or = 10% beta < or = 25% when the lots were divided in five clusters. When the interval between UT and LT was larger than 10% (e.g. 15%), we were able to select precise LQAS plans dividing the lot in five clusters with N = 50 (5 x 10) and d = 4 to evaluate programmes with 95% coverage target and d = 7 to evaluate programmes with 90% target. These plans will considerably increase the feasibility and the rapidity of conducting the LQAS in the field.

Ability of commercial demineralized freeze-dried bone allograft to induce new bone formation.

PubMed

Schwartz, Z; Mellonig, J T; Carnes, D L; de la Fontaine, J; Cochran, D L; Dean, D D; Boyan, B D

1996-09-01

Demineralized freeze-dried bone allograft (DFDBA) has been used extensively in periodontal therapy. The rationale for use of DFDBA includes the fact that proteins capable of inducing new bone; i.e., bone morphogenetic proteins, can be isolated from bone grafts. Commercial bone banks have provided DFDBA to the dental practitioner for many years; however, these organizations have not verified the osteoinductive capacity of their DFDBA preparations. The aim of this study was to determine the ability of commercial DFDBA preparations to induce new bone formation. DFDBA with particle sizes ranging from 200 to 500 microns was received from six bone banks using various bone production methods. Different lots of DFDBA from the same tissue bank were sometimes available. A total of 14 lots were examined. The surface area of bone particles in each sample was measured morphometrically and the pH of a solution containing the particles after suspension in distilled water determined. Samples from each DFDBA lot were implanted intramuscularly (10 mg) or subcutaneously (20 mg) into three different animals and tissue biopsies harvested after 4 weeks. One sample from each tissue bank was implanted and harvested after 8 weeks. At harvest, each area where DFDBA had been implanted was excised and examined by light microscopy. The ability of DFDBA to produce new bone was evaluated and the amount of residual bone particles measured. The results show that bone particles from all tissue banks had a variety of shapes and sizes, both before implantation and after 1 or 2 months of implantation. The pH of particle suspensions also varied between batches, as well as between tissue banks. None of the DFDBA induced new bone formation when implanted subcutaneously. Intramuscular implants from three banks induced new bone formation after 1 and 2 months. DFDBA from two banks caused new bone formation only after 2 months. However, DFDBA from one bank did not induce new bone at all. Particle size before implantation correlated with particle size after implantation. However, particle size did not correlate with ability to induce bone. The results show that commercial DFDBA differs in both size and ability to induce new bone formation, but that the two are not related. The study also indicates that wide variation in commercial bone bank preparations of DFDBA exist and that ability to induce new bone formation also varies widely. Furthermore, the results suggest that methods or assays for evaluating the ability of DFDBA to induce new bone should be developed and standardized.

Temporal Fluctuations in Foreign Language Motivation: Results of a Longitudinal Study

ERIC Educational Resources Information Center

Kruk, Mariusz

2016-01-01

According to Ellis (2008), motivation has received a lot of interest in language learning. It is unfortunate, however, that little attention has been paid to the dynamic nature of the construct, particularly changes in motivation within single classes and series of lessons. The study whose results are reported in this paper aims at investigating…

Effect of metrology time delay on overlay APC

NASA Astrophysics Data System (ADS)

Carlson, Alan; DiBiase, Debra

2002-07-01

The run-to-run control strategy of lithography APC is primarily composed of a feedback loop as shown in the diagram below. It is known that the insertion of a time delay in a feedback loop can cause degradation in control performance and could even cause a stable system to become unstable, if the time delay becomes sufficiently large. Many proponents of integrated metrology methods have cited the damage caused by metrology time delays as the primary justification for moving from a stand-alone to integrated metrology. While there is little dispute over the qualitative form of this argument, there has been very light published about the quantitative effects under real fab conditions - precisely how much control is lost due to these time delays. Another issue regarding time delays is that the length of these delays is not typically fixed - they vary from lot to lot and in some cases this variance can be large - from one hour on the short side to over 32 hours on the long side. Concern has been expressed that the variability in metrology time delays can cause undesirable dynamics in feedback loops that make it difficult to optimize feedback filters and gains and at worst could drive a system unstable. By using data from numerous fabs, spanning many sizes and styles of operation, we have conducted a quantitative study of the time delay effect on overlay run- to-run control. Our analysis resulted in the following conclusions: (1) There is a significant and material relationship between metrology time delay and overlay control under a variety of real world production conditions. (2) The run-to-run controller can be configured to minimize sensitivity to time delay variations. (3) The value of moving to integrated metrology can be quantified.

[Epidemiological dynamics of Dengue on Easter Island].

PubMed

Canals, Mauricio; González, Christian; Canals, Andrea; Figueroa, Daniela

2012-08-01

Dengue is considered an emerging disease with an increasing prevalence especially in South America. In 2002, an epidemic of classic Dengue (DENV-1) occurred unexpectedly on Easter Island, where it had never been detected before. It reappeared in 2006-2007 and 2008, 2009 and 2011. The aim of this study was to estimate the most relevant parameters of the epidemiological dynamics of transmission of Dengue on Easter Island and to model the dynamics since 2002, comparing the predictions with the actual situation observed. Of the total cases, 52.27% were females and 47.73% men. The average age of infection was 31.38 ± 18.37 years, similar in men and women. We estimated the reproductive number R0 = 3.005 with an IC0,95 = [1.92, 4.61]. The inter-epidemic period reached an estimated T = 5.20 to 6.8 years. The case simulation showed recurrent epidemics with decreasing magnitude (damped oscillations), which is a known phenomenon in models of dengue and malaria. There was good qualitative fit to the epidemiological dynamics from 2002 onwards. It accurately predicted the rise in cases between 2006 and 2011. The predicted number of cases during the 2002 epidemic is greater than the confirmed cases and the predicted epidemic was faster than notified cases. Interepidemic period in the simulation was 6.72 years between 2002 and 2008 and 4.68 years between 2008 and 2013. From the theoretical perspective, the first epidemic had affected 94% of the population (approximately 3500 cases), but 639 were reported suggesting underreporting and a lot of sub-clinical cases occurred. Future epidemic of decreasing size are expected, although the main danger are epidemics of hemorrhagic dengue fever resulting from the introduction of different dengue virus serotypes.

Aerosol transport simulations in indoor and outdoor environments using computational fluid dynamics (CFD)

NASA Astrophysics Data System (ADS)

Landazuri, Andrea C.

This dissertation focuses on aerosol transport modeling in occupational environments and mining sites in Arizona using computational fluid dynamics (CFD). The impacts of human exposure in both environments are explored with the emphasis on turbulence, wind speed, wind direction and particle sizes. Final emissions simulations involved the digitalization process of available elevation contour plots of one of the mining sites to account for realistic topographical features. The digital elevation map (DEM) of one of the sites was imported to COMSOL MULTIPHYSICSRTM for subsequent turbulence and particle simulations. Simulation results that include realistic topography show considerable deviations of wind direction. Inter-element correlation results using metal and metalloid size resolved concentration data using a Micro-Orifice Uniform Deposit Impactor (MOUDI) under given wind speeds and directions provided guidance on groups of metals that coexist throughout mining activities. Groups between Fe-Mg, Cr-Fe, Al-Sc, Sc-Fe, and Mg-Al are strongly correlated for unrestricted wind directions and speeds, suggesting that the source may be of soil origin (e.g. ore and tailings); also, groups of elements where Cu is present, in the coarse fraction range, may come from mechanical action mining activities and saltation phenomenon. Besides, MOUDI data under low wind speeds (<2 m/s) and at night showed a strong correlation for 1 mum particles between the groups: Sc-Be-Mg, Cr-Al, Cu-Mn, Cd-Pb-Be, Cd-Cr, Cu-Pb, Pb-Cd, As-Cd-Pb. The As-Cd-Pb correlates strongly in almost all ranges of particle sizes. When restricted low wind speeds were imposed more groups of elements are evident and this may be justified with the fact that at lower speeds particles are more likely to settle. When linking these results with CFD simulations and Pb-isotope results it is concluded that the source of elements found in association with Pb in the fine fraction come from the ore that is subsequently processed in the smelter site, whereas the source of elements associated to Pb in the coarse fraction is of different origin. CFD simulation results will not only provide realistic and quantifiable information in terms of potential deleterious effects, but also that the application of CFD represents an important contribution to actual dispersion modeling studies; therefore, Computational Fluid Dynamics can be used as a source apportionment tool to identify areas that have an effect over specific sampling points and susceptible regions under certain meteorological conditions, and these conclusions can be supported with inter-element correlation matrices and lead isotope analysis, especially since there is limited access to the mining sites. Additional results concluded that grid adaption is a powerful tool that allows to refine specific regions that require lots of detail and therefore better resolve flow detail, provides higher number of locations with monotonic convergence than the manual grids, and requires the least computational effort. CFD simulations were approached using the k-epsilon model, with the aid of computer aided engineering software: ANSYSRTM and COMSOL MULTIPHYSICS RTM. The success of aerosol transport simulations depends on a good simulation of the turbulent flow. A lot of attention was placed on investigating and choosing the best models in terms of convergence, independence and computational effort. This dissertation also includes preliminary studies of transient discrete phase, eulerian and species transport modeling, importance of saltation of particles, information on CFD methods, and strategies for future directions that should be taken.

7 CFR 987.112a - Grade, size, and container requirements for each outlet category.

Code of Federal Regulations, 2010 CFR

2010-01-01

... shall be designated by the Committee for each market research project. The handling of each lot of dates... containers for testing in connection with a research project conducted by or in cooperation with the... dates have been converted from their whole or pitted form, they may be shipped to any market in the...

7 CFR 923.322 - Washington cherry handling regulation.

Code of Federal Regulations, 2011 CFR

2011-01-01

... solids as determined from a composite sample by refractometer prior to packing, at time of packing, or at... designation the row count/row size marked shall be one of those shown in Column 1 of the following table and... diameter shown in Column 2 of such table: Provided, That the content of individual containers in the lot...

7 CFR 923.322 - Washington cherry handling regulation.

Code of Federal Regulations, 2012 CFR

2012-01-01

... solids as determined from a composite sample by refractometer prior to packing, at time of packing, or at... designation the row count/row size marked shall be one of those shown in Column 1 of the following table and... diameter shown in Column 2 of such table: Provided, That the content of individual containers in the lot...

7 CFR 923.322 - Washington cherry handling regulation.

Code of Federal Regulations, 2014 CFR

2014-01-01

... solids as determined from a composite sample by refractometer prior to packing, at time of packing, or at... designation the row count/row size marked shall be one of those shown in Column 1 of the following table and... diameter shown in Column 2 of such table: Provided, That the content of individual containers in the lot...

7 CFR 923.322 - Washington cherry handling regulation.

Code of Federal Regulations, 2013 CFR

2013-01-01

... solids as determined from a composite sample by refractometer prior to packing, at time of packing, or at... designation the row count/row size marked shall be one of those shown in Column 1 of the following table and... diameter shown in Column 2 of such table: Provided, That the content of individual containers in the lot...

The fragmented nature of tundra landscape

NASA Astrophysics Data System (ADS)

Virtanen, Tarmo; Ek, Malin

2014-04-01

The vegetation and land cover structure of tundra areas is fragmented when compared to other biomes. Thus, satellite images of high resolution are required for producing land cover classifications, in order to reveal the actual distribution of land cover types across these large and remote areas. We produced and compared different land cover classifications using three satellite images (QuickBird, Aster and Landsat TM5) with different pixel sizes (2.4 m, 15 m and 30 m pixel size, respectively). The study area, in north-eastern European Russia, was visited in July 2007 to obtain ground reference data. The QuickBird image was classified using supervised segmentation techniques, while the Aster and Landsat TM5 images were classified using a pixel-based supervised classification method. The QuickBird classification showed the highest accuracy when tested against field data, while the Aster image was generally more problematic to classify than the Landsat TM5 image. Use of smaller pixel sized images distinguished much greater levels of landscape fragmentation. The overall mean patch sizes in the QuickBird, Aster, and Landsat TM5-classifications were 871 m2, 2141 m2 and 7433 m2, respectively. In the QuickBird classification, the mean patch size of all the tundra and peatland vegetation classes was smaller than one pixel of the Landsat TM5 image. Water bodies and fens in particular occur in the landscape in small or elongated patches, and thus cannot be realistically classified from larger pixel sized images. Land cover patterns vary considerably at such a fine-scale, so that a lot of information is lost if only medium resolution satellite images are used. It is crucial to know the amount and spatial distribution of different vegetation types in arctic landscapes, as carbon dynamics and other climate related physical, geological and biological processes are known to vary greatly between vegetation types.

Preparation of Chemical Compounds for the U.S. Army Drug Development Program

DTIC Science & Technology

1990-09-14

Aldrich, Lot No. ML0824ML Johns Manville , no Lot No. J.T. Baker, Lot No. A42837 Fisher Scientific Lot No. 885835-60 Ashland, Lot No. 0701768E...Aldrich, Lot No. 03905ET Moore-Tec, No Lot No. Lot Nos. KAPM and KDPA Aaper, Lot Nos. R9529, 89D19-R, 89K06 Kodak, Lot No. 807198C Johns Manville , Lot...89-K06-R and 90-A124-R Fisher, Lot Nos. 881166-60, 895184-36 and 894961-36 Kodak, Lot NO. 807198C Johns Manville Lot Nos. G5P34633 and 3P-291

Polarization in the land distribution, land use and land cover change in the Amazon

PubMed Central

D'ANTONA, Alvaro; VANWEY, Leah; LUDEWIGS, Thomas

2013-01-01

The objective of this article is to present Polarization of Agrarian Structure as a single, more complete representation than models emphasizing rural exodus and consolidation of land into large agropastoral enterprises of the dynamics of changing land distribution, land use / cover, and thus the rural milieu of Amazonia. Data were collected in 2003 using social surveys on a sample of 587 lots randomly selected from among 5,086 lots on a cadastral map produced in the 1970s. Georeferencing of current property boundaries in the location of these previously demarcated lots allows us to relate sociodemographic and biophysical variables of the surveyed properties to the changes in boundaries that have occurred since the 1970s. As have other authors in other Amazonian regions, we found concentration of land ownership into larger properties. The approach we took, however, showed that changes in the distribution of land ownership is not limited to the appearance of larger properties, those with 200 ha or more; there also exists substantial division of earlier lots into properties with fewer than five hectares, many without any agropastoral use. These two trends are juxtaposed against the decline in establishments with between five and 200 ha. The variation across groups in land use / land cover and population distribution shows the necessity of developing conceptual models, whether from socioeconomic, demographic or environmental perspectives, look beyond a single group of people or properties. PMID:24639597

HYPERSAMP - HYPERGEOMETRIC ATTRIBUTE SAMPLING SYSTEM BASED ON RISK AND FRACTION DEFECTIVE

NASA Technical Reports Server (NTRS)

De, Salvo L. J.

1994-01-01

HYPERSAMP is a demonstration of an attribute sampling system developed to determine the minimum sample size required for any preselected value for consumer's risk and fraction of nonconforming. This statistical method can be used in place of MIL-STD-105E sampling plans when a minimum sample size is desirable, such as when tests are destructive or expensive. HYPERSAMP utilizes the Hypergeometric Distribution and can be used for any fraction nonconforming. The program employs an iterative technique that circumvents the obstacle presented by the factorial of a non-whole number. HYPERSAMP provides the required Hypergeometric sample size for any equivalent real number of nonconformances in the lot or batch under evaluation. Many currently used sampling systems, such as the MIL-STD-105E, utilize the Binomial or the Poisson equations as an estimate of the Hypergeometric when performing inspection by attributes. However, this is primarily because of the difficulty in calculation of the factorials required by the Hypergeometric. Sampling plans based on the Binomial or Poisson equations will result in the maximum sample size possible with the Hypergeometric. The difference in the sample sizes between the Poisson or Binomial and the Hypergeometric can be significant. For example, a lot size of 400 devices with an error rate of 1.0% and a confidence of 99% would require a sample size of 400 (all units would need to be inspected) for the Binomial sampling plan and only 273 for a Hypergeometric sampling plan. The Hypergeometric results in a savings of 127 units, a significant reduction in the required sample size. HYPERSAMP is a demonstration program and is limited to sampling plans with zero defectives in the sample (acceptance number of zero). Since it is only a demonstration program, the sample size determination is limited to sample sizes of 1500 or less. The Hypergeometric Attribute Sampling System demonstration code is a spreadsheet program written for IBM PC compatible computers running DOS and Lotus 1-2-3 or Quattro Pro. This program is distributed on a 5.25 inch 360K MS-DOS format diskette, and the program price includes documentation. This statistical method was developed in 1992.

Large scale Full QM-MD investigation of small peptides and insulin adsorption on ideal and defective TiO2 (1 0 0) surfaces. Influence of peptide size on interfacial bonds

NASA Astrophysics Data System (ADS)

Dubot, Pierre; Boisseau, Nicolas; Cenedese, Pierre

2018-05-01

Large biomolecule interaction with oxide surface has attracted a lot of attention because it drives behavior of implanted devices in the living body. To investigate the role of TiO2 surface structure on a large polypeptide (insulin) adsorption, we use a homemade mixed Molecular Dynamics-Full large scale Quantum Mechanics code. A specific re-parameterized (Ti) and globally convergent NDDO method fitted on high level ab initio method (coupled cluster CCSD(T) and DFT) allows us to safely describe the electronic structure of the whole insulin-TiO2 surface system (up to 4000 atoms). Looking specifically at carboxylate residues, we demonstrate in this work that specific interfacial bonds are obtained from the insulin/TiO2 system that are not observed in the case of smaller peptides (tripeptides, insulin segment chains with different configurations). We also demonstrate that a large part of the adsorption energy is compensated by insulin conformational energy changes and surface defects enhanced this trend. Large slab dimensions allow us to take into account surface defects that are actually beyond ab initio capabilities owing to size effect. These results highlight the influence of the surface structure on the conformation and therefore of the possible inactivity of an adsorbed polypeptides.

Losing a Job: The Nonpecuniary Cost of Unemployment in the United States

ERIC Educational Resources Information Center

Young, Cristobal

2012-01-01

Drawing on the Panel Study of Income Dynamics, I track the subjective well-being of individuals as they enter and exit unemployment. Job loss is a salient trigger event that sets off large changes in well-being. The factors expected to improve the lot of the unemployed have limited efficacy: (1) changes in family income are not significantly…

Equilibrium sampling by reweighting nonequilibrium simulation trajectories

NASA Astrophysics Data System (ADS)

Yang, Cheng; Wan, Biao; Xu, Shun; Wang, Yanting; Zhou, Xin

2016-03-01

Based on equilibrium molecular simulations, it is usually difficult to efficiently visit the whole conformational space of complex systems, which are separated into some metastable regions by high free energy barriers. Nonequilibrium simulations could enhance transitions among these metastable regions and then be applied to sample equilibrium distributions in complex systems, since the associated nonequilibrium effects can be removed by employing the Jarzynski equality (JE). Here we present such a systematical method, named reweighted nonequilibrium ensemble dynamics (RNED), to efficiently sample equilibrium conformations. The RNED is a combination of the JE and our previous reweighted ensemble dynamics (RED) method. The original JE reproduces equilibrium from lots of nonequilibrium trajectories but requires that the initial distribution of these trajectories is equilibrium. The RED reweights many equilibrium trajectories from an arbitrary initial distribution to get the equilibrium distribution, whereas the RNED has both advantages of the two methods, reproducing equilibrium from lots of nonequilibrium simulation trajectories with an arbitrary initial conformational distribution. We illustrated the application of the RNED in a toy model and in a Lennard-Jones fluid to detect its liquid-solid phase coexistence. The results indicate that the RNED sufficiently extends the application of both the original JE and the RED in equilibrium sampling of complex systems.

Equilibrium sampling by reweighting nonequilibrium simulation trajectories.

PubMed

Yang, Cheng; Wan, Biao; Xu, Shun; Wang, Yanting; Zhou, Xin

2016-03-01

Based on equilibrium molecular simulations, it is usually difficult to efficiently visit the whole conformational space of complex systems, which are separated into some metastable regions by high free energy barriers. Nonequilibrium simulations could enhance transitions among these metastable regions and then be applied to sample equilibrium distributions in complex systems, since the associated nonequilibrium effects can be removed by employing the Jarzynski equality (JE). Here we present such a systematical method, named reweighted nonequilibrium ensemble dynamics (RNED), to efficiently sample equilibrium conformations. The RNED is a combination of the JE and our previous reweighted ensemble dynamics (RED) method. The original JE reproduces equilibrium from lots of nonequilibrium trajectories but requires that the initial distribution of these trajectories is equilibrium. The RED reweights many equilibrium trajectories from an arbitrary initial distribution to get the equilibrium distribution, whereas the RNED has both advantages of the two methods, reproducing equilibrium from lots of nonequilibrium simulation trajectories with an arbitrary initial conformational distribution. We illustrated the application of the RNED in a toy model and in a Lennard-Jones fluid to detect its liquid-solid phase coexistence. The results indicate that the RNED sufficiently extends the application of both the original JE and the RED in equilibrium sampling of complex systems.

Low-Rank Linear Dynamical Systems for Motor Imagery EEG.

PubMed

Zhang, Wenchang; Sun, Fuchun; Tan, Chuanqi; Liu, Shaobo

2016-01-01

The common spatial pattern (CSP) and other spatiospectral feature extraction methods have become the most effective and successful approaches to solve the problem of motor imagery electroencephalography (MI-EEG) pattern recognition from multichannel neural activity in recent years. However, these methods need a lot of preprocessing and postprocessing such as filtering, demean, and spatiospectral feature fusion, which influence the classification accuracy easily. In this paper, we utilize linear dynamical systems (LDSs) for EEG signals feature extraction and classification. LDSs model has lots of advantages such as simultaneous spatial and temporal feature matrix generation, free of preprocessing or postprocessing, and low cost. Furthermore, a low-rank matrix decomposition approach is introduced to get rid of noise and resting state component in order to improve the robustness of the system. Then, we propose a low-rank LDSs algorithm to decompose feature subspace of LDSs on finite Grassmannian and obtain a better performance. Extensive experiments are carried out on public dataset from "BCI Competition III Dataset IVa" and "BCI Competition IV Database 2a." The results show that our proposed three methods yield higher accuracies compared with prevailing approaches such as CSP and CSSP.

Manufacture and evaluation of Li/BCX DD cells

NASA Technical Reports Server (NTRS)

Meyer, S.; Takeuchi, E.

1990-01-01

This project is divided into four main tasks: cell manufacture, acceptance, and lot certification of cells, performance testing of cells, and abuse testing of cells. Lithium/bromine chloride in thionyl chloride (Li/BCX) 149 DD cells (PN 3B2085-XA) were built according to the provisions of Electrochem Industries Quality Plan 17096. Acceptance and lot certification testing was performed according to NASA JSC Document EP5-83-025, Revision B. Acceptance testing included open circuit and load voltage check, visual examination, size and weight measurements, and high temperature exposure. Lot certification tests were performed for capacity performance and for performance under conditions of thermal and electrical abuse. These tests included 149 C exposure, capacity discharge, fuse check, high temperature exposure, high rate discharge, short circuit, vibration, and overdischarge testing. A quantity of 200 cells was delivered to Johnson Space Center for life test evaluation. A parametric evaluation of the capacity discharge of Li/BCX DD cells was performed over a variety of temperatures and discharge rates. This testing served to map the performance capability of the cell. Tests were also performed over a variety of electrical and thermal abuse conditions. Abuse tests included short circuit, charging, overdischarge, high temperature exposure, shock, and vibration.

Particle-associated contaminants in street dust, parking lot dust, soil, lake-bottom sediment, and suspended and streambed sediment, Lake Como and Fosdic Lake watersheds, Fort Worth, Texas, 2004

USGS Publications Warehouse

Wilson, Jennifer T.; Van Metre, Peter C.; Werth, Charles J.; Yang, Yanning

2006-01-01

A previous study by the U.S. Geological Survey of impaired water bodies in Fort Worth, Texas, reported elevated but variable concentrations of particle-associated contaminants (PACs) comprising chlorinated hydrocarbons, polycyclic aromatic hydrocarbons, and trace elements in suspended and bed sediment of lakes and streams affected by urban land use. The U.S. Geological Survey, in cooperation with the City of Fort Worth, collected additional samples during October 2004 to investigate sources of PACs in the watersheds of two impaired lakes: Lake Como and Fosdic Lake. Source materials and aquatic sediment were sampled and analyzed for PACs. Source materials sampled consisted of street dust and soil from areas with residential and commercial land use and parking lot dust from sealed and unsealed parking lots. Aquatic sediment sampled consisted of bottom-sediment cores from the two lakes and suspended and streambed sediment from the influent stream of each lake. Samples were analyzed for chlorinated hydrocarbons (organochlorine pesticides and polychlorinated biphenyls), polycyclic aromatic hydrocarbons, major and trace elements, organic carbon, grain size, and radionuclides.

77 FR 53906 - Notice of Proposed Withdrawal and Opportunity for Public Meeting; California

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-04

...\\; Sec. 32, lots 4 and 5; Sec. 34, lot 4. T. 13 N., R. 10 E., Sec. 2, lot 1, and lots 3 to 15, inclusive; Sec. 9, lots 8, 12, and 13, and SW\\1/4\\NE\\1/4\\; Sec. 10, lots 1 to 10, inclusive, E\\1/2\\NE\\1/4\\, E\\1/2..., inclusive, S\\1/2\\ of lot 5, S\\1/2\\ of lot 8, lots 11 and 13; Sec. 19, lot 24; Sec. 20, lots 1, 2, 3, and 8...

Estimation after classification using lot quality assurance sampling: corrections for curtailed sampling with application to evaluating polio vaccination campaigns.

PubMed

Olives, Casey; Valadez, Joseph J; Pagano, Marcello

2014-03-01

To assess the bias incurred when curtailment of Lot Quality Assurance Sampling (LQAS) is ignored, to present unbiased estimators, to consider the impact of cluster sampling by simulation and to apply our method to published polio immunization data from Nigeria. We present estimators of coverage when using two kinds of curtailed LQAS strategies: semicurtailed and curtailed. We study the proposed estimators with independent and clustered data using three field-tested LQAS designs for assessing polio vaccination coverage, with samples of size 60 and decision rules of 9, 21 and 33, and compare them to biased maximum likelihood estimators. Lastly, we present estimates of polio vaccination coverage from previously published data in 20 local government authorities (LGAs) from five Nigerian states. Simulations illustrate substantial bias if one ignores the curtailed sampling design. Proposed estimators show no bias. Clustering does not affect the bias of these estimators. Across simulations, standard errors show signs of inflation as clustering increases. Neither sampling strategy nor LQAS design influences estimates of polio vaccination coverage in 20 Nigerian LGAs. When coverage is low, semicurtailed LQAS strategies considerably reduces the sample size required to make a decision. Curtailed LQAS designs further reduce the sample size when coverage is high. Results presented dispel the misconception that curtailed LQAS data are unsuitable for estimation. These findings augment the utility of LQAS as a tool for monitoring vaccination efforts by demonstrating that unbiased estimation using curtailed designs is not only possible but these designs also reduce the sample size. © 2014 John Wiley & Sons Ltd.

Bellman Ford algorithm - in Routing Information Protocol (RIP)

NASA Astrophysics Data System (ADS)

Krianto Sulaiman, Oris; Mahmud Siregar, Amir; Nasution, Khairuddin; Haramaini, Tasliyah

2018-04-01

In a large scale network need a routing that can handle a lot number of users, one of the solutions to cope with large scale network is by using a routing protocol, There are 2 types of routing protocol that is static and dynamic, Static routing is manually route input based on network admin, while dynamic routing is automatically route input formed based on existing network. Dynamic routing is efficient used to network extensively because of the input of route automatic formed, Routing Information Protocol (RIP) is one of dynamic routing that uses the bellman-ford algorithm where this algorithm will search for the best path that traversed the network by leveraging the value of each link, so with the bellman-ford algorithm owned by RIP can optimize existing networks.

Low-cost digital dynamic visualization system

NASA Astrophysics Data System (ADS)

Asundi, Anand K.; Sajan, M. R.

1995-05-01

High speed photographic systems like the image rotation camera, the Cranz Schardin camera and the drum camera are typically used for recording and visualization of dynamic events in stress analysis, fluid mechanics, etc. All these systems are fairly expensive and generally not simple to use. Furthermore they are all based on photographic film recording systems requiring time consuming and tedious wet processing of the films. Currently digital cameras are replacing to certain extent the conventional cameras for static experiments. Recently, there is lot of interest in developing and modifying CCD architectures and recording arrangements for dynamic scene analysis. Herein we report the use of a CCD camera operating in the Time Delay and Integration (TDI) mode for digitally recording dynamic scenes. Applications in solid as well as fluid impact problems are presented.

iGUVs: Preparing Giant Unilamellar Vesicles with a Smartphone and Lipids Easily Extracted from Chicken Eggs

ERIC Educational Resources Information Center

Almendro Vedia, Víctor G.; Natale, Paolo; Chen, Su; Monroy, Francisco; Rosilio, Veronique; López-Montero, Ivan

2017-01-01

Since the first report of electroformed micrometer-sized liposomes in the 1980s, giant unilamellar vesicles (GUVs) have generated a lot of interest in the biophysical and biochemical communities. However, their penetration rate in high school or at the undergraduate level is still limited because of the requirement of specialized materials for…

Digitally-Enabled Organizational Routines at the Organization-Environment Boundary: Buffering and the Role of Technology

ERIC Educational Resources Information Center

Hillison, Derek William

2009-01-01

Boundary units of an organization uniquely experience the tension between adaptation to environmental variation and maintaining stable outcomes for the rest of the organization. In our world of just-in-time supply chain systems, lot-sizes of one, lean manufacturing and an increasing focus on services, traditional forms of buffering such as queuing…

Moving the Education Needle: A Conversation with Scott Hamilton

ERIC Educational Resources Information Center

Jacobs, Joanne

2014-01-01

Scott Hamilton is the Forrest Gump of education reform, although with a lot more IQ points and fewer chocolates. He worked for Bill Bennett in the U.S. Department of Education and for Benno Schmidt at the Edison Project. He authorized charter schools in Massachusetts, co-founded the KIPP network, quadrupled the size of Teach For America (TFA), and…

A stepwise, 'test-all-positives' methodology to assess gluten-kernel contamination at the serving-size level in gluten-free (GF) oat production.

PubMed

Chen, Yumin; Fritz, Ronald D; Kock, Lindsay; Garg, Dinesh; Davis, R Mark; Kasturi, Prabhakar

2018-02-01

A step-wise, 'test-all-positive-gluten' analytical methodology has been developed and verified to assess kernel-based gluten contamination (i.e., wheat, barley and rye kernels) during gluten-free (GF) oat production. It targets GF claim compliance at the serving-size level (of a pouch or approximately 40-50g). Oat groats are collected from GF oat production following a robust attribute-based sampling plan then split into 75-g subsamples, and ground. R-Biopharm R5 sandwich ELISA R7001 is used for analysis of all the first15-g portions of the ground sample. A >20-ppm result disqualifies the production lot, while a >5 to <20-ppm result triggers complete analysis of the remaining 60-g of ground sample, analyzed in 15-g portions. If all five 15-g test results are <20ppm, and their average is <10.67ppm (since a 20-ppm contaminant in 40g of oats would dilute to 10.67ppm in 75-g), the lot is passed. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Determination of supplier-to-supplier and lot-to-lot variability in glycation of recombinant human serum albumin expressed in Oryza sativa.

PubMed

Frahm, Grant E; Smith, Daryl G S; Kane, Anita; Lorbetskie, Barry; Cyr, Terry D; Girard, Michel; Johnston, Michael J W

2014-01-01

The use of different expression systems to produce the same recombinant human protein can result in expression-dependent chemical modifications (CMs) leading to variability of structure, stability and immunogenicity. Of particular interest are recombinant human proteins expressed in plant-based systems, which have shown particularly high CM variability. In studies presented here, recombinant human serum albumins (rHSA) produced in Oryza sativa (Asian rice) (OsrHSA) from a number of suppliers have been extensively characterized and compared to plasma-derived HSA (pHSA) and rHSA expressed in yeast (Pichia pastoris and Saccharomyces cerevisiae). The heterogeneity of each sample was evaluated using size exclusion chromatography (SEC), reversed-phase high-performance liquid chromatography (RP-HPLC) and capillary electrophoresis (CE). Modifications of the samples were identified by liquid chromatography-mass spectrometry (LC-MS). The secondary and tertiary structure of the albumin samples were assessed with far U/V circular dichroism spectropolarimetry (far U/V CD) and fluorescence spectroscopy, respectively. Far U/V CD and fluorescence analyses were also used to assess thermal stability and drug binding. High molecular weight aggregates in OsrHSA samples were detected with SEC and supplier-to-supplier variability and, more critically, lot-to-lot variability in one manufactures supplied products were identified. LC-MS analysis identified a greater number of hexose-glycated arginine and lysine residues on OsrHSA compared to pHSA or rHSA expressed in yeast. This analysis also showed supplier-to-supplier and lot-to-lot variability in the degree of glycation at specific lysine and arginine residues for OsrHSA. Both the number of glycated residues and the degree of glycation correlated positively with the quantity of non-monomeric species and the chromatographic profiles of the samples. Tertiary structural changes were observed for most OsrHSA samples which correlated well with the degree of arginine/lysine glycation. The extensive glycation of OsrHSA from multiple suppliers may have further implications for the use of OsrHSA as a therapeutic product.

Reviews

NASA Astrophysics Data System (ADS)

2006-11-01

WE RECOMMEND Critical mass Philip Ball explores the idea of the physics of society. Eurekas and Euphorias A humorous yet insightful collection of scientific anecdotes. Wind turbine Low-cost wind turbine produces excellent results. Science Center Nemo Hands-on science centre has some great displays for teenagers. Crocodile Physics There’s something for everyone in this lesson software package. Wireless Dynamics Sensor System A fun way to measure and record altitude and acceleration. WORTH A LOOK Climate Change Begins at Home This well researched book tackles the issue of saving our planet. The Little Doctor Datalogger Datalogger has lots of facilities but needs some manual processing. HANDLE WITH CARE The Physics of Basketball Only of interest to budding physicists obsessed with basketball. Virtual Physics This package offers nice simulations but not a lot else. WEB WATCH An eclectic mix of nuclear- and general-physics websites.

Simulation study on compressive laminar optical tomography for cardiac action potential propagation

PubMed Central

Harada, Takumi; Tomii, Naoki; Manago, Shota; Kobayashi, Etsuko; Sakuma, Ichiro

2017-01-01

To measure the activity of tissue at the microscopic level, laminar optical tomography (LOT), which is a microscopic form of diffuse optical tomography, has been developed. However, obtaining sufficient recording speed to determine rapidly changing dynamic activity remains major challenges. For a high frame rate of the reconstructed data, we here propose a new LOT method using compressed sensing theory, called compressive laminar optical tomography (CLOT), in which novel digital micromirror device-based illumination and data reduction in a single reconstruction are applied. In the simulation experiments, the reconstructed volumetric images of the action potentials that were acquired from 5 measured images with random pattern featured a wave border at least to a depth of 2.5 mm. Consequently, it was shown that CLOT has potential for over 200 fps required for the cardiac electrophysiological phenomena. PMID:28736675

On the diverse roles of fluid dynamic drag in animal swimming and flying

PubMed Central

2018-01-01

Questions of energy dissipation or friction appear immediately when addressing the problem of a body moving in a fluid. For the most simple problems, involving a constant steady propulsive force on the body, a straightforward relation can be established balancing this driving force with a skin friction or form drag, depending on the Reynolds number and body geometry. This elementary relation closes the full dynamical problem and sets, for instance, average cruising velocity or energy cost. In the case of finite-sized and time-deformable bodies though, such as flapping flyers or undulatory swimmers, the comprehension of driving/dissipation interactions is not straightforward. The intrinsic unsteadiness of the flapping and deforming animal bodies complicates the usual application of classical fluid dynamic forces balance. One of the complications is because the shape of the body is indeed changing in time, accelerating and decelerating perpetually, but also because the role of drag (more specifically the role of the local drag) has two different facets, contributing at the same time to global dissipation and to driving forces. This causes situations where a strong drag is not necessarily equivalent to inefficient systems. A lot of living systems are precisely using strong sources of drag to optimize their performance. In addition to revisiting classical results under the light of recent research on these questions, we discuss in this review the crucial role of drag from another point of view that concerns the fluid–structure interaction problem of animal locomotion. We consider, in particular, the dynamic subtleties brought by the quadratic drag that resists transverse motions of a flexible body or appendage performing complex kinematics, such as the phase dynamics of a flexible flapping wing, the propagative nature of the bending wave in undulatory swimmers, or the surprising relevance of drag-based resistive thrust in inertial swimmers. PMID:29445037

Firing rate dynamics in recurrent spiking neural networks with intrinsic and network heterogeneity.

PubMed

Ly, Cheng

2015-12-01

Heterogeneity of neural attributes has recently gained a lot of attention and is increasing recognized as a crucial feature in neural processing. Despite its importance, this physiological feature has traditionally been neglected in theoretical studies of cortical neural networks. Thus, there is still a lot unknown about the consequences of cellular and circuit heterogeneity in spiking neural networks. In particular, combining network or synaptic heterogeneity and intrinsic heterogeneity has yet to be considered systematically despite the fact that both are known to exist and likely have significant roles in neural network dynamics. In a canonical recurrent spiking neural network model, we study how these two forms of heterogeneity lead to different distributions of excitatory firing rates. To analytically characterize how these types of heterogeneities affect the network, we employ a dimension reduction method that relies on a combination of Monte Carlo simulations and probability density function equations. We find that the relationship between intrinsic and network heterogeneity has a strong effect on the overall level of heterogeneity of the firing rates. Specifically, this relationship can lead to amplification or attenuation of firing rate heterogeneity, and these effects depend on whether the recurrent network is firing asynchronously or rhythmically firing. These observations are captured with the aforementioned reduction method, and furthermore simpler analytic descriptions based on this dimension reduction method are developed. The final analytic descriptions provide compact and descriptive formulas for how the relationship between intrinsic and network heterogeneity determines the firing rate heterogeneity dynamics in various settings.

Dynamic value assessments in oncology supported by the PACE Continuous Innovation Indicators.

PubMed

Paddock, Silvia; Goodman, Clifford; Shortenhaus, Scott; Grainger, David; Zummo, Jacqueline; Thomas, Samuel

2017-10-01

Several recently developed frameworks aim to assess the value of cancer treatments, but the most appropriate metrics remain uncertain. We use data from the Patient Access to Cancer care Excellence Continuous Innovation Indicators to examine the relationship between hazard ratios (HRs) from clinical trials and dynamic therapeutic value accumulating over time. Our analysis shows that HRs from initial clinical trials poorly predict the eventual therapeutic value of cancer treatments. Relying strongly on HRs from registration trials to predict the long-term success of treatments leaves a lot of the variance unexplained. The Continuous Innovation Indicators offer a complementing, dynamic method to track the therapeutic value of cancer treatments and continuously update value assessments as additional evidence accumulates.

High-Resolution X-Ray Telescopes

NASA Technical Reports Server (NTRS)

ODell, Stephen L.; Brissenden, Roger J.; Davis, William; Elsner, Ronald F.; Elvis, Martin; Freeman, Mark; Gaetz, Terry; Gorenstein, Paul; Gubarev, Mikhail V.

2010-01-01

Fundamental needs for future x-ray telescopes: a) Sharp images => excellent angular resolution. b) High throughput => large aperture areas. Generation-X optics technical challenges: a) High resolution => precision mirrors & alignment. b) Large apertures => lots of lightweight mirrors. Innovation needed for technical readiness: a) 4 top-level error terms contribute to image size. b) There are approaches to controlling those errors. Innovation needed for manufacturing readiness. Programmatic issues are comparably challenging.

Dynamic photoelasticity by TDI imaging

NASA Astrophysics Data System (ADS)

Asundi, Anand K.; Sajan, M. R.

2001-06-01

High speed photographic system like the image rotation camera, the Cranz Schardin camera and the drum camera are typically used for the recording and visualization of dynamic events in stress analysis, fluid mechanics, etc. All these systems are fairly expensive and generally not simple to use. Furthermore they are all based on photographic film recording system requiring time consuming and tedious wet processing of the films. Digital cameras are replacing the conventional cameras, to certain extent in static experiments. Recently, there is lots of interest in development and modifying CCD architectures and recording arrangements for dynamic scenes analysis. Herein we report the use of a CCD camera operating in the Time Delay and Integration mode for digitally recording dynamic photoelastic stress patterns. Applications in strobe and streak photoelastic pattern recording and system limitations will be explained in the paper.

Artificial neural network (ANN)-based prediction of depth filter loading capacity for filter sizing.

PubMed

Agarwal, Harshit; Rathore, Anurag S; Hadpe, Sandeep Ramesh; Alva, Solomon J

2016-11-01

This article presents an application of artificial neural network (ANN) modelling towards prediction of depth filter loading capacity for clarification of a monoclonal antibody (mAb) product during commercial manufacturing. The effect of operating parameters on filter loading capacity was evaluated based on the analysis of change in the differential pressure (DP) as a function of time. The proposed ANN model uses inlet stream properties (feed turbidity, feed cell count, feed cell viability), flux, and time to predict the corresponding DP. The ANN contained a single output layer with ten neurons in hidden layer and employed a sigmoidal activation function. This network was trained with 174 training points, 37 validation points, and 37 test points. Further, a pressure cut-off of 1.1 bar was used for sizing the filter area required under each operating condition. The modelling results showed that there was excellent agreement between the predicted and experimental data with a regression coefficient (R 2 ) of 0.98. The developed ANN model was used for performing variable depth filter sizing for different clarification lots. Monte-Carlo simulation was performed to estimate the cost savings by using different filter areas for different clarification lots rather than using the same filter area. A 10% saving in cost of goods was obtained for this operation. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:1436-1443, 2016. © 2016 American Institute of Chemical Engineers.

Use of spring-roll EAP actuator applied as end-effector of a hyper-redundant robot

NASA Astrophysics Data System (ADS)

Errico, Gianmarco; Fava, Victor; Resta, Ferruccio; Ripamonti, Francesco

2015-04-01

This paper presents a hyper-redundant continuous robot used to perform work in places which humans can not reach. This type of robot is generally a bio-inspired solution, it is composed by a lot of flexible segments driven by multiple actuators and its dynamics is described by a lot degrees of freedom. In this paper a model composed of some rigid links connected to each other by revolution joint is presented. In each link a torsional spring is added in order to simulate the resistant torque between the links and the interactions among the cables and the robot during the relative rotation. Moreover a type of EAP actuator, called spring roll, is used as the end-effector of the robot. Through a suitable sensor, such as a camera, the spring roll allows to track a target and it closes the control loop on the robot to follow it.

Evaluation of Commercial Automotive-Grade BME Capacitors

NASA Technical Reports Server (NTRS)

Liu, Donhang

2014-01-01

Three Ni-BaTiO3 ceramic capacitor lots with the same specification (chip size, capacitance, and rated voltage) and the same reliability level, made by three different manufacturers, were degraded using highly accelerated life stress testing (HALST) with the same temperature and applied voltage conditions. The reliability, as characterized by mean time to failure (MTTF), differed by more than one order of magnitude among the capacitor lots. A theoretical model based on the existence of depletion layers at grain boundaries and the entrapment of oxygen vacancies has been proposed to explain the MTTF difference among these BME capacitors. It is the conclusion of this model that reliability will not be improved simply by increasing the insulation resistance of a BME capacitor. Indeed, Ni-BaTiO3 ceramic capacitors with a smaller degradation rate constant K will always give rise to a longer reliability life.

Evaluation of Commercial Automotive-Grade BME Capacitors

NASA Technical Reports Server (NTRS)

Liu, Donhang

2014-01-01

Three Ni-BaTiO3 ceramic capacitor lots with the same specification (chip size, capacitance, and rated voltage) and the same reliability level, made by three different manufacturers, were degraded using highly accelerated life stress testing (HALST) with the same temperature and applied voltage conditions. The reliability, as characterized by mean time to failure (MTTF), differed by more than one order of magnitude among the capacitor lots. A theoretical model based on the existence of depletion layers at grain boundaries and the entrapment of oxygen vacancies has been proposed to explain the MTTF difference among these BME capacitors. It is the conclusion of this model that reliability will not be improved simply by increasing the insulation resistance of a BME capacitor. Indeed, Ni-BaTiO3 ceramic capacitors with a smaller degradation rate constant K will always give rise to a longer reliability life

Cluster designs to assess the prevalence of acute malnutrition by lot quality assurance sampling: a validation study by computer simulation.

PubMed

Olives, Casey; Pagano, Marcello; Deitchler, Megan; Hedt, Bethany L; Egge, Kari; Valadez, Joseph J

2009-04-01

Traditional lot quality assurance sampling (LQAS) methods require simple random sampling to guarantee valid results. However, cluster sampling has been proposed to reduce the number of random starting points. This study uses simulations to examine the classification error of two such designs, a 67x3 (67 clusters of three observations) and a 33x6 (33 clusters of six observations) sampling scheme to assess the prevalence of global acute malnutrition (GAM). Further, we explore the use of a 67x3 sequential sampling scheme for LQAS classification of GAM prevalence. Results indicate that, for independent clusters with moderate intracluster correlation for the GAM outcome, the three sampling designs maintain approximate validity for LQAS analysis. Sequential sampling can substantially reduce the average sample size that is required for data collection. The presence of intercluster correlation can impact dramatically the classification error that is associated with LQAS analysis.

Lot quality assurance sampling for monitoring immunization programmes: cost-efficient or quick and dirty?

PubMed

Sandiford, P

1993-09-01

In recent years Lot quality assurance sampling (LQAS), a method derived from production-line industry, has been advocated as an efficient means to evaluate the coverage rates achieved by child immunization programmes. This paper examines the assumptions on which LQAS is based and the effect that these assumptions have on its utility as a management tool. It shows that the attractively low sample sizes used in LQAS are achieved at the expense of specificity unless unrealistic assumptions are made about the distribution of coverage rates amongst the immunization programmes to which the method is applied. Although it is a very sensitive test and its negative predictive value is probably high in most settings, its specificity and positive predictive value are likely to be low. The implications of these strengths and weaknesses with regard to management decision-making are discussed.

Mathematical model of parking space unit for triangular parking area

NASA Astrophysics Data System (ADS)

Syahrini, Intan; Sundari, Teti; Iskandar, Taufiq; Halfiani, Vera; Munzir, Said; Ramli, Marwan

2018-01-01

Parking space unit (PSU) is an effective measure for the area size of a vehicle, including the free space and the width of the door opening of the vehicle (car). This article discusses a mathematical model for parking space of vehicles in triangular shape area. An optimization model for triangular parking lot is developed. Integer Linear Programming (ILP) method is used to determine the maximum number of the PSU. The triangular parking lot is in isosceles and equilateral triangles shape and implements four possible rows and five possible angles for each field. The vehicles which are considered are cars and motorcycles. The results show that the isosceles triangular parking area has 218 units of optimal PSU, which are 84 units of PSU for cars and 134 units of PSU for motorcycles. Equilateral triangular parking area has 688 units of optimal PSU, which are 175 units of PSU for cars and 513 units of PSU for motorcycles.

Estimating degradation in real time and accelerated stability tests with random lot-to-lot variation: a simulation study.

PubMed

Magari, Robert T

2002-03-01

The effect of different lot-to-lot variability levels on the prediction of stability are studied based on two statistical models for estimating degradation in real time and accelerated stability tests. Lot-to-lot variability is considered as random in both models, and is attributed to two sources-variability at time zero, and variability of degradation rate. Real-time stability tests are modeled as a function of time while accelerated stability tests as a function of time and temperatures. Several data sets were simulated, and a maximum likelihood approach was used for estimation. The 95% confidence intervals for the degradation rate depend on the amount of lot-to-lot variability. When lot-to-lot degradation rate variability is relatively large (CV > or = 8%) the estimated confidence intervals do not represent the trend for individual lots. In such cases it is recommended to analyze each lot individually. Copyright 2002 Wiley-Liss, Inc. and the American Pharmaceutical Association J Pharm Sci 91: 893-899, 2002

Stability of total nutrient admixtures in reference to ambient temperatures.

PubMed

Lee, Myung Duk; Yoon, Jeung-Ei; Kim, Sang-In; Kim, In-Chul

2003-10-01

To evaluate the stability of emulsions under different temperatures simulating clinical conditions of storage and exposure during infusion, five total nutrient admixture formulas in this institution were analyzed: adult, patients with hepatic failure, infants, stressed patients, and patients with renal failure. Each mixture was allocated in a sterile 100-mL glass bottle, which was prefilled and refilled with nitrogen gas. Bottles were stored at 4 degrees C for 0 d, 3 d, and 7 d and then exposed to three different temperatures: usual room temperature (18 degrees C to 25 degrees C), high (>28 degrees C) in a water bath, or storage (4 degrees C) for 24 and 48 h. The gross inspection of the emulsions and parallel measurements of pH, particle sizes, divalent ions, peroxide levels, and microbial cultures were performed. Every lot was stable near 18 degrees C, but 8 of 10 lots stored for 7 d (25 degrees C and >28 degrees C) and 15 of 20 lots stored for 3 and 7 d (25 degrees C and >28 degrees C) showed coalescence. The overall coalescence incidences by storage, exposure, and heat were statistically significant (P < 0.005). For the safety of total nutrient admixtures, special attention is required to keep the ambient temperature below 28 degrees C and completely exclude air from the container.

Estimation of Microbial Concentration in Food Products from Qualitative, Microbiological Test Data with the MPN Technique.

PubMed

Fujikawa, Hiroshi

2017-01-01

Microbial concentration in samples of a food product lot has been generally assumed to follow the log-normal distribution in food sampling, but this distribution cannot accommodate the concentration of zero. In the present study, first, a probabilistic study with the most probable number (MPN) technique was done for a target microbe present at a low (or zero) concentration in food products. Namely, based on the number of target pathogen-positive samples in the total samples of a product found by a qualitative, microbiological examination, the concentration of the pathogen in the product was estimated by means of the MPN technique. The effects of the sample size and the total sample number of a product were then examined. Second, operating characteristic (OC) curves for the concentration of a target microbe in a product lot were generated on the assumption that the concentration of a target microbe could be expressed with the Poisson distribution. OC curves for Salmonella and Cronobacter sakazakii in powdered formulae for infants and young children were successfully generated. The present study suggested that the MPN technique and the Poisson distribution would be useful for qualitative microbiological test data analysis for a target microbe whose concentration in a lot is expected to be low.

Development of Markup Language for Medical Record Charting: A Charting Language.

PubMed

Jung, Won-Mo; Chae, Younbyoung; Jang, Bo-Hyoung

2015-01-01

Nowadays a lot of trials for collecting electronic medical records (EMRs) exist. However, structuring data format for EMR is an especially labour-intensive task for practitioners. Here we propose a new mark-up language for medical record charting (called Charting Language), which borrows useful properties from programming languages. Thus, with Charting Language, the text data described in dynamic situation can be easily used to extract information.

Dynamic Network Analysis for Robust Uncertainty Management

DTIC Science & Technology

2010-03-01

complex networks since a set of modules could be a lot simpler than a collection of entangled individual agents (22). The simplification may be...nanomaterials and photonic crystals with desired material prop- 233 C.l. FAST GENERATION OF POTENTIALS FOR SELF-ASSEMBLY OF PARTICLES erties [14-21...prescribed geometry and structure is highly motivated by the desire to produce photonic crystals with specified optical properties. Also, we intend to

Creating the City: An Interview with Antonia Darder and Pepón Osorio

ERIC Educational Resources Information Center

Herman, David, Jr.; Kraehe, Amelia; Bartholomee, Lucy; Lewis, Tyson

2017-01-01

Today there is a lot of discussion about creative economies and how cities are the engines driving growth in a variety of industries. But cities are not merely rows of buildings, or sets of laws, such as zoning ordinances or parking regulations. A city is, rather, a set of dynamic experiences that we all participate in as co(labor)ators. As a way…

76 FR 28076 - Notice of Inventory Completion: Museum of Anthropology, Washington State University, Pullman, WA...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-13

... scrapers, 1 bone scraper handle, 1 lot of mussel shells, 1 lot of red ochre, 2 bone awls, 1 lot of charcoal... lots of bag residue, 4 lots of animal bones, 1 stone net sinker, 1 lot of tin can fragments, 2...

Compressed Sensing and Electron Microscopy

DTIC Science & Technology

2010-01-01

dimensional space IRn and so there is a lot of collapsing of information. For example, any vector η in the null space N = N (Φ) of Φ is mapped...assignment of the pixel intensity f̂P in the image. Thus, the pixels size is the same as the grid spacing h and we can ( with only a slight abuse of notation...offers a fresh view of signal/image acquisition and reconstruction.

Economic analysis of the gypsy moth problem in the northeast: II. applied to residential property

Treesearch

Brian R. Payne; William B. White; Roger E. McCay; Robert R. McNichols

1973-01-01

Guidelines are presented for determining dollar losses in residential property values from tree mortality caused by the gypsy moth. The method is based on an earlier study in Amherst, Massachusetts, of the contribution of trees to property values. For each target area, the method requires data on property value, lot size, and number of trees 6 inches dbh and larger for...

What parts of a house and yard landscape are homeowners maintaining for wildfire safety?

Treesearch

Christine Vogt; Sarah McCaffrey; Greg Winter

2010-01-01

Homeownership can be a lot of work. Interior maintenance and housekeeping; outdoor maintenance and weekly yard work–all part of the drill. The investment of time and money can be substantial depending on the size and condition of the home and acreage, or the amount of vegetation, including deciduous trees and other woody matter in a yard. Homeowners in high fire risk...

Modeling residential lawn fertilization practices: integrating high resolution remote sensing with socioeconomic data.

PubMed

Zhou, Weiqi; Troy, Austin; Grove, Morgan

2008-05-01

This article investigates how remotely sensed lawn characteristics, such as parcel lawn area and parcel lawn greenness, combined with household characteristics, can be used to predict household lawn fertilization practices on private residential lands. This study involves two watersheds, Glyndon and Baisman's Run, in Baltimore County, Maryland, USA. Parcel lawn area and lawn greenness were derived from high-resolution aerial imagery using an object-oriented classification approach. Four indicators of household characteristics, including lot size, square footage of the house, housing value, and housing age were obtained from a property database. Residential lawn care survey data combined with remotely sensed parcel lawn area and greenness data were used to estimate two measures of household lawn fertilization practices, household annual fertilizer nitrogen application amount (N_yr) and household annual fertilizer nitrogen application rate (N_ha_yr). Using multiple regression with multi-model inferential procedures, we found that a combination of parcel lawn area and parcel lawn greenness best predicts N_yr, whereas a combination of parcel lawn greenness and lot size best predicts variation in N_ha_yr. Our analyses show that household fertilization practices can be effectively predicted by remotely sensed lawn indices and household characteristics. This has significant implications for urban watershed managers and modelers.

The influence of product brand-to-brand variability on superdisintegrant Performance. A case study with croscarmellose sodium.

PubMed

Zhao, Na; Augsburger, L L

2006-01-01

The purpose of this study is to investigate factors influencing croscarmellose sodium functionality with special emphasis on developing a discriminating model tablet formulation to evaluate product brand-to-brand variability. The particle size distribution, water uptake, and swelling properties of five brands of croscarmellose sodium in either neutral water or 0.1 N HCl were studied. Differences were observed in all properties between brands. Media with acidic pH had a negative impact, but to different extents, on both the water uptake and swelling of all croscarmellose sodium brands due to the presence of carboxymethyl sodium substituents. A tablet matrix composed of lactose (75% w/w) and dicalcium phosphate (25% wt/wt) was used to compare the functional equivalency of the five brands of croscarmellose sodium. The tablet disintegration times were inversely proportional to the swelling ability of superdisintegrant in the testing medium regardless of medium temperature and disintegrant concentration. In conclusion; the particle size, total degree of substitution, and the ratio of basic to acidic substituents are important factors that should be considered during product optimization. The tablet matrix composed of lactose and dicalcium phosphate at a weight ratio of 3:1 can be used as a model formulation for product lot-to-lot consistency and product brand-to-brand comparison purposes.

LQAS usefulness in an emergency department.

PubMed

de la Orden, Susana Granado; Rodríguez-Rieiro, Cristina; Sánchez-Gómez, Amaya; García, Ana Chacón; Hernández-Fernández, Tomás; Revilla, Angel Abad; Escribano, Dolores Vigil; Pérez, Paz Rodríguez

2008-01-01

This paper aims to explore lot quality assurance sampling (LQAS) applicability and usefulness in the evaluation of quality indicators in a hospital emergency department (ED) and to determine the degree of compliance with quality standards according to this sampling method. Descriptive observational research in the Hospital General Universitario Gregorio Marañón (HGUGM) emergency department (ED). Patients older than 15 years, diagnosed with dyspnoea, chest pain, urinary tract colic or bronchial asthma attending the HGUGM ED from December 2005 to May 2006, and patients admitted during 2005 with exacerbation of chronic obstructive pulmonary disease or acute meningitis were included in the study. Sample sizes were calculated using LQAS. Different quality indicators, one for each process, were selected. The upper (acceptable quality level (AQL)) and lower thresholds (rejectable quality level (RQL)) were established considering risk alpha = 5 per cent and beta = 20 per cent, and the minimum number of observations required was calculated. It was impossible to reach the necessary sample size for bronchial asthma and urinary tract colic patients. For chest pain, acute exacerbation of chronic obstructive pulmonary disease, and acute meningitis, quality problems were detected. The lot was accepted only for the dyspnoea indicator. The usefulness of LQAS to detect quality problems in the management of health processes in one hospital's ED. The LQAS could complement traditional sampling methods.

Powder Bed Layer Characteristics: The Overseen First-Order Process Input

NASA Astrophysics Data System (ADS)

Mindt, H. W.; Megahed, M.; Lavery, N. P.; Holmes, M. A.; Brown, S. G. R.

2016-08-01

Powder Bed Additive Manufacturing offers unique advantages in terms of manufacturing cost, lot size, and product complexity compared to traditional processes such as casting, where a minimum lot size is mandatory to achieve economic competitiveness. Many studies—both experimental and numerical—are dedicated to the analysis of how process parameters such as heat source power, scan speed, and scan strategy affect the final material properties. Apart from the general urge to increase the build rate using thicker powder layers, the coating process and how the powder is distributed on the processing table has received very little attention to date. This paper focuses on the first step of every powder bed build process: Coating the process table. A numerical study is performed to investigate how powder is transferred from the source to the processing table. A solid coating blade is modeled to spread commercial Ti-6Al-4V powder. The resulting powder layer is analyzed statistically to determine the packing density and its variation across the processing table. The results are compared with literature reports using the so-called "rain" models. A parameter study is performed to identify the influence of process table displacement and wiper velocity on the powder distribution. The achieved packing density and how that affects subsequent heat source interaction with the powder bed is also investigated numerically.

Sampling hazelnuts for aflatoxin: uncertainty associated with sampling, sample preparation, and analysis.

PubMed

Ozay, Guner; Seyhan, Ferda; Yilmaz, Aysun; Whitaker, Thomas B; Slate, Andrew B; Giesbrecht, Francis

2006-01-01

The variability associated with the aflatoxin test procedure used to estimate aflatoxin levels in bulk shipments of hazelnuts was investigated. Sixteen 10 kg samples of shelled hazelnuts were taken from each of 20 lots that were suspected of aflatoxin contamination. The total variance associated with testing shelled hazelnuts was estimated and partitioned into sampling, sample preparation, and analytical variance components. Each variance component increased as aflatoxin concentration (either B1 or total) increased. With the use of regression analysis, mathematical expressions were developed to model the relationship between aflatoxin concentration and the total, sampling, sample preparation, and analytical variances. The expressions for these relationships were used to estimate the variance for any sample size, subsample size, and number of analyses for a specific aflatoxin concentration. The sampling, sample preparation, and analytical variances associated with estimating aflatoxin in a hazelnut lot at a total aflatoxin level of 10 ng/g and using a 10 kg sample, a 50 g subsample, dry comminution with a Robot Coupe mill, and a high-performance liquid chromatographic analytical method are 174.40, 0.74, and 0.27, respectively. The sampling, sample preparation, and analytical steps of the aflatoxin test procedure accounted for 99.4, 0.4, and 0.2% of the total variability, respectively.

Valuable water

NASA Astrophysics Data System (ADS)

Carlowicz, Michael

In some places, money flows with water. Studying both the water quality and property values around 22 lakes in south-central Maine, Kevin Boyle and Holly James of the University of Maine and Roy Bouchard of the Maine Department of Environmental Protection have found that good water quality makes waterfront property even more valuable. To gauge water quality, the researchers used Secchi disks to measure the clarity of the water at depth. They also reviewed 543 lakefront property sales between 1990 and 1994 to determine how values correlated with changing water conditions. The group also considered such factors as lake frontage, sizes of the houses and lots, and size of the lake.

Effects of greening and community reuse of vacant lots on crime

PubMed Central

Kondo, Michelle; Hohl, Bernadette; Han, SeungHoon; Branas, Charles

2016-01-01

The Youngstown Neighborhood Development Corporation initiated a ‘Lots of Green’ programme to reuse vacant land in 2010. We performed a difference-in-differences analysis of the effects of this programme on crime in and around newly treated lots, in comparison to crimes in and around randomly selected and matched, untreated vacant lot controls. The effects of two types of vacant lot treatments on crime were tested: a cleaning and greening ‘stabilisation’ treatment and a ‘community reuse’ treatment mostly involving community gardens. The combined effects of both types of vacant lot treatments were also tested. After adjustment for various sociodemographic factors, linear and Poisson regression models demonstrated statistically significant reductions in all crime classes for at least one lot treatment type. Regression models adjusted for spatial autocorrelation found the most consistent significant reductions in burglaries around stabilisation lots, and in assaults around community reuse lots. Spill-over crime reduction effects were found in contiguous areas around newly treated lots. Significant increases in motor vehicle thefts around both types of lots were also found after they had been greened. Community-initiated vacant lot greening may have a greater impact on reducing more serious, violent crimes. PMID:28529389

UAV Trajectory Modeling Using Neural Networks

NASA Technical Reports Server (NTRS)

Xue, Min

2017-01-01

Massive small unmanned aerial vehicles are envisioned to operate in the near future. While there are lots of research problems need to be addressed before dense operations can happen, trajectory modeling remains as one of the keys to understand and develop policies, regulations, and requirements for safe and efficient unmanned aerial vehicle operations. The fidelity requirement of a small unmanned vehicle trajectory model is high because these vehicles are sensitive to winds due to their small size and low operational altitude. Both vehicle control systems and dynamic models are needed for trajectory modeling, which makes the modeling a great challenge, especially considering the fact that manufactures are not willing to share their control systems. This work proposed to use a neural network approach for modelling small unmanned vehicle's trajectory without knowing its control system and bypassing exhaustive efforts for aerodynamic parameter identification. As a proof of concept, instead of collecting data from flight tests, this work used the trajectory data generated by a mathematical vehicle model for training and testing the neural network. The results showed great promise because the trained neural network can predict 4D trajectories accurately, and prediction errors were less than 2:0 meters in both temporal and spatial dimensions.

Conflict for Resources: Water in the Lake Chad Basin

DTIC Science & Technology

2009-01-01

Security 19 (1994), http://www.library.utoronto.ca/pcs/evidence (accessed 10 February 2009). 11 Miriam Lowi, Water and Power (Cambridge, UK : Cambridge...states wage wars and how scarce natural resources influence the states. Carl von Clausewitz’s treatise, On War serves as a starting point for any...has lots of water, very little of it is freshwater. Miriam Lowi, author of Water and Power describes political dynamics of high and low politics. High

Half-Life Learning Curves in the Defense Acquisition Life Cycle

DTIC Science & Technology

2012-07-01

International Journal of Production Economics , 83(1), 95–111. Jaber, M. Y., & Bonney, M. (2007). Economic Manufacture Quantity (EMQ) model with lot...size dependent learning and forgetting rates. International Journal of Production Economics , 108(1–2), 359–367. Jaber, M.Y., & Guiffrida, A. L. (2008...189(1), 93–104. Jaber, M. Y., Hemant, K. V., & Darwin D. J. (2003). Countering forgetting through training and deployment. International Journal of

75 FR 80872 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-23

... which it handles and executes odd lot and mixed lot orders.\\3\\ If CBSX is not displaying the NBBO and... mixed lot orders will be handled and executed in a more consistent manner with round lot orders. \\3\\ A... lot'' order is an order for a quantity that is less than 100. A ``mixed lot'' order is an order for a...

Comprehensive analysis of statistical and model-based overlay lot disposition methods

NASA Astrophysics Data System (ADS)

Crow, David A.; Flugaur, Ken; Pellegrini, Joseph C.; Joubert, Etienne L.

2001-08-01

Overlay lot disposition algorithms in lithography occupy some of the highest leverage decision points in the microelectronic manufacturing process. In a typical large volume sub-0.18micrometers fab the lithography lot disposition decision is made about 500 times per day. Each decision will send a lot of wafers either to the next irreversible process step or back to rework in an attempt to improve unacceptable overlay performance. In the case of rework, the intention is that the reworked lot will represent better yield (and thus more value) than the original lot and that the enhanced lot value will exceed the cost of rework. Given that the estimated cost of reworking a critical-level lot is around 10,000 (based upon the opportunity cost of consuming time on a state-of-the-art DUV scanner), we are faced with the implication that the lithography lot disposition decision process impacts up to 5 million per day in decisions. That means that a 1% error rate in this decision process represents over 18 million per year lost in profit for a representative sit. Remarkably, despite this huge leverage, the lithography lot disposition decision algorithm usually receives minimal attention. In many cases, this lack of attention has resulted in the retention of sub-optimal algorithms from earlier process generations and a significant negative impact on the economic output of many high-volume manufacturing sites. An ideal lot- dispositioning algorithm would be an algorithm that results into the best economic decision being made every time - lots would only be reworked where the expected value (EV) of the reworked lot minus the expected value of the original lot exceeds the cost of the rework: EV(reworked lot)- EV(original lot)>COST(rework process) Calculating the above expected values in real-time has generally been deemed too complicated and maintenance-intensive to be practical for fab operations, so a simplified rule is typically used.

Heterogeneity in the distribution of genetically modified and conventional oilseed rape within fields and seed lots.

PubMed

Begg, Graham S; Elliott, Martin J; Cullen, Danny W; Iannetta, Pietro P M; Squire, Geoff R

2008-10-01

The implementation of co-existence in the commercialisation of GM crops requires GM and non-GM products to be segregated in production and supply. However, maintaining segregation in oilseed rape will be made difficult by the highly persistent nature of this species. An understanding of its population dynamics is needed to predict persistence and develop potential strategies for control, while to ensure segregation is being achieved, the production of GM oilseed rape must be accompanied by the monitoring of GM levels in crop or seed populations. Heterogeneity in the spatial distribution of oilseed rape has the potential to affect both control and monitoring and, although a universal phenomenon in arable weeds and harvested seed lots, spatial heterogeneity in oilseed rape populations remains to be demonstrated and quantified. Here we investigate the distribution of crop and volunteer populations in a commercial field before and during the cultivation of the first conventional oilseed rape (winter) crop since the cultivation of a GM glufosinate-tolerant oilseed rape crop (spring) three years previously. GM presence was detected by ELISA for the PAT protein in each of three morphologically distinguishable phenotypes: autumn germinating crop-type plants (3% GM), autumn-germinating 'regrowths' (72% GM) and spring germinating 'small-type' plants (17% GM). Statistical models (Poisson log-normal and binomial logit-normal) were used to describe the spatial distribution of these populations at multiple spatial scales in the field and of GM presence in the harvested seed lot. Heterogeneity was a consistent feature in the distribution of GM and conventional oilseed rape. Large trends across the field (50 x 400 m) and seed lot (4 x 1.5 x 1.5 m) were observed in addition to small-scale heterogeneity, less than 20 m in the field and 20 cm in the seed lot. The heterogeneity was greater for the 'regrowth' and 'small' phenotypes, which were likely to be volunteers and included most of the GM plants detected, than for the largely non-GM 'crop' phenotype. The implications of the volunteer heterogeneity for field management and GM-sampling are discussed.

Immunogenicity and safety of the candidate RTS,S/AS01 vaccine in young Nigerian children: a randomized, double-blind, lot-to-lot consistency trial.

PubMed

Umeh, Rich; Oguche, Stephen; Oguonu, Tagbo; Pitmang, Simon; Shu, Elvis; Onyia, Jude-Tony; Daniyam, Comfort A; Shwe, David; Ahmad, Abdullahi; Jongert, Erik; Catteau, Grégory; Lievens, Marc; Ofori-Anyinam, Opokua; Leach, Amanda

2014-11-12

For regulatory approval, consistency in manufacturing of vaccine lots is expected to be demonstrated in confirmatory immunogenicity studies using two-sided equivalence trials. This randomized, double-blind study (NCT01323972) assessed consistency of three RTS,S/AS01 malaria vaccine batches formulated from commercial-scale purified antigen bulk lots in terms of anti-CS-responses induced. Healthy children aged 5-17 months were randomized (1:1:1:1) to receive RTS,S/AS01 at 0-1-2 months from one of three commercial-scale purified antigen bulk lots (1600 litres-fermentation scale; commercial-scale lots), or a comparator vaccine batch made from pilot-scale purified antigen bulk lot (20 litres-fermentation scale; pilot-scale lot). The co-primary objectives were to first demonstrate consistency of antibody responses against circumsporozoite (CS) protein at one month post-dose 3 for the three commercial-scale lots and second demonstrate non-inferiority of anti-CS antibody responses at one month post-dose 3 for the commercial-scale lots compared to the pilot-scale lot. Safety and reactogenicity were evaluated as secondary endpoints. One month post-dose-3, anti-CS antibody geometric mean titres (GMT) for the 3 commercial scale lots were 319.6 EU/ml (95% confidence interval (CI): 268.9-379.8), 241.4 EU/ml (207.6-280.7), and 302.3 EU/ml (259.4-352.3). Consistency for the RTS,S/AS01 commercial-scale lots was demonstrated as the two-sided 95% CI of the anti-CS antibody GMT ratio between each pair of lots was within the range of 0.5-2.0. GMT of the pooled commercial-scale lots (285.8 EU/ml (260.7-313.3)) was non-inferior to the pilot-scale lot (271.7 EU/ml (228.5-323.1)). Each RTS,S/AS01 lot had an acceptable tolerability profile, with infrequent reports of grade 3 solicited symptoms. No safety signals were identified and no serious adverse events were considered related to vaccination. RTS,S/AS01 lots formulated from commercial-scale purified antigen bulk batches induced a consistent anti-CS antibody response, and the anti-CS GMT of pooled commercial-scale lots was non-inferior to that of a lot formulated from a pilot-scale antigen bulk batch. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Nitrous Oxide Emissions from Open-Lot Cattle Feedyards: A Review.

PubMed

Waldrip, Heidi M; Todd, Richard W; Parker, David B; Cole, N Andy; Rotz, C Alan; Casey, Kenneth D

2016-11-01

Nitrous oxide (NO) emissions from concentrated animal feeding operations, including cattle feedyards, have become an important research topic. However, there are limitations to current measurement techniques, uncertainty in the magnitude of feedyard NO fluxes, and a lack of effective mitigation methods. The objective of this review was to assess NO emission from cattle feedyards, including comparison of measured and modeled emission rates, discussion of measurement methods, and evaluation of mitigation options. Published annual per capita flux rates for beef cattle feedyards and open-lot dairies were highly variable and ranged from 0.002 to 4.3 kg NO animal yr. On an area basis, published emission rates ranged from 0 to 41 mg NO m h. From these studies and Intergovernmental Panel on Climate Change emission factors, calculated daily per capita NO fluxes averaged 18 ± 10 g NO animal d (range, 0.04-67 g NO animal d). This variation was due to inconsistency in measurement techniques as well as irregularity in NO production and emission attributable to management, animal diet, and environmental conditions. Based on this review, it is clear that the magnitude and dynamics of NO emissions from open-lot cattle systems are not well understood. Further research is required to quantify feedyard NO fluxes and develop cost-effective mitigation methods. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

7 CFR 983.52 - Failed lots/rework procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., ARIZONA, AND NEW MEXICO Regulations § 983.52 Failed lots/rework procedure. (a) Substandard pistachios. Each lot of substandard pistachios may be reworked to meet aflatoxin or quality requirements. The... reporting. If a lot fails to meet the aflatoxin and/or the quality requirements of this part, a failed lot...

Methodology For Reduction Of Sampling On The Visual Inspection Of Developed And Etched Wafers

NASA Astrophysics Data System (ADS)

van de Ven, Jamie S.; Khorasani, Fred

1989-07-01

There is a lot of inspection in the manufacturing of semiconductor devices. Generally, the more important a manufacturing step, the higher is the level of inspection. In some cases 100% of the wafers are inspected after certain steps. Inspection is a non-value added and expensive activity. It requires an army of "inspectors," often times expensive equipment and becomes a "bottle neck" when the level of inspection is high. Although inspection helps identify quality problems, it hurts productivity. The new management, quality and productivity philosophies recommend against over inspection. [Point #3 in Dr. Deming's 14 Points for Management (1)] 100% inspection is quite unnecessary . Often the nature of a process allows us to reduce inspection drastically and still maintain a high level of confidence in quality. In section 2, we discuss such situations and show that some elementary probability theory allows us to determine sample sizes and measure the chances of catching a bad "lot" and accepting a good lot. In section 3, we provide an example and application of the theory, and make a few comments on money and time saved because of this work. Finally, in section 4, we draw some conclusions about the new quality and productivity philosophies and how applied statisticians and engineers should study every situation individually and avoid blindly using methods and tables given in books.

Lack of evidence for the presence of emerging HoBi-like viruses in North American fetal bovine serum lots.

PubMed

Bauermann, Fernando V; Flores, Eduardo F; Falkenberg, Shollie M; Weiblen, Rudi; Ridpath, Julia F

2014-01-01

The detection of an emerging pestivirus species, "HoBi-like virus," in fetal bovine serum (FBS) labeled as U.S. origin, but packaged in Europe, raised concerns that HoBi-like virus may have entered the United States. In the current study, 90 lots of FBS originating in North America (NA) were screened for pestivirus antigen and antibodies. Lots in group 1 (G1, 72 samples) and group 2 (G2, 9 samples) originated in NA and were packaged in the United States. Group 3 (G3) was composed of 9 lots collected in NA and processed in Europe. Lots in G1 were claimed negative for Bovine viral diarrhea virus (BVDV), while lots in G2 and G3 were claimed positive by the commercial processor. All lots in G1 and G2 tested negative by reverse transcription polymerase chain reaction (RT-PCR) using HoBi-like-specific primers. Two G1 lots tested positive by BVDV RT-PCR. One of these was also positive by virus isolation. All G2 lots were positive by BVDV RT-PCR. In addition, four G2 lots were VI positive while 1 lot was antigen-capture enzyme-linked immunosorbent assay (ELISA) positive. Two G3 lots were positive by HoBi-like-specific RT-PCR tests. All lots were negative for HoBi_D32/00 neutralizing antibodies. Seven lots (4 G1; 1 G2; 2 G3) had antibodies against BVDV by virus neutralization and/or antigen-capture ELISA. While there is no evidence of HoBi-like viruses in NA based on tested samples, further studies are required to validate HoBi-like virus-free status and develop means to prevent the spread of HoBi-like virus into NA.

Assessing gull abundance and food availability in urban parking lots

USGS Publications Warehouse

Clark, Daniel E.; Whitney, Jillian J.; MacKenzie, Kenneth G.; Koenen, Kiana K. G.; DeStefano, Stephen

2015-01-01

Feeding birds is a common activity throughout the world; yet, little is known about the extent of feeding gulls in urban areas. We monitored 8 parking lots in central Massachusetts, USA, during the fall and winter of 2011 to 2013 in 4 monitoring sessions to document the number of gulls present, the frequency of human–gull feeding interactions, and the effectiveness of signage and direct interaction in reducing human-provisioned food. Parking lots were divided between “education” and “no-education” lots. In education lots, we erected signs about problems caused when people feed birds and also asked people to stop feeding birds. We did not erect signs or ask people to stop feeding birds at no-education lots. We spent >1,200 hours in parking lots (range = 136 to 200 hours per parking lot), and gulls were counted every 20 minutes. We conducted >4,000 counts, and ring-billed gulls (Lorus delawarensis) accounted for 98% of all gulls. Our educational efforts were minimally effective. There were fewer feedings (P = 0.01) in education lots during one of the monitoring sessions but significantly more gulls (P = 0.008) in education lots during 2 monitoring sessions. While there was a marginal decrease (P = 0.055) in the number of feedings after no-education lots were transformed into education lots, there was no difference in gull numbers in these lots (P = 0.16). Education appears to have some influence in reducing the number of people feeding gulls, but our efforts were not able to reduce the number of human feeders or the amount of food enough to influence the number of gulls using parking lots.

The contribution of lot-to-lot variation to the measurement uncertainty of an LC-MS-based multi-mycotoxin assay.

PubMed

Stadler, David; Sulyok, Michael; Schuhmacher, Rainer; Berthiller, Franz; Krska, Rudolf

2018-05-01

Multi-mycotoxin determination by LC-MS is commonly based on external solvent-based or matrix-matched calibration and, if necessary, the correction for the method bias. In everyday practice, the method bias (expressed as apparent recovery RA), which may be caused by losses during the recovery process and/or signal/suppression enhancement, is evaluated by replicate analysis of a single spiked lot of a matrix. However, RA may vary for different lots of the same matrix, i.e., lot-to-lot variation, which can result in a higher relative expanded measurement uncertainty (U r ). We applied a straightforward procedure for the calculation of U r from the within-laboratory reproducibility, which is also called intermediate precision, and the uncertainty of RA (u r,RA ). To estimate the contribution of the lot-to-lot variation to U r , the measurement results of one replicate of seven different lots of figs and maize and seven replicates of a single lot of these matrices, respectively, were used to calculate U r . The lot-to-lot variation was contributing to u r,RA and thus to U r for the majority of the 66 evaluated analytes in both figs and maize. The major contributions of the lot-to-lot variation to u r,RA were differences in analyte recovery in figs and relative matrix effects in maize. U r was estimated from long-term participation in proficiency test schemes with 58%. Provided proper validation, a fit-for-purpose U r of 50% was proposed for measurement results obtained by an LC-MS-based multi-mycotoxin assay, independent of the concentration of the analytes.

A Secure and Efficient Audit Mechanism for Dynamic Shared Data in Cloud Storage

PubMed Central

2014-01-01

With popularization of cloud services, multiple users easily share and update their data through cloud storage. For data integrity and consistency in the cloud storage, the audit mechanisms were proposed. However, existing approaches have some security vulnerabilities and require a lot of computational overheads. This paper proposes a secure and efficient audit mechanism for dynamic shared data in cloud storage. The proposed scheme prevents a malicious cloud service provider from deceiving an auditor. Moreover, it devises a new index table management method and reduces the auditing cost by employing less complex operations. We prove the resistance against some attacks and show less computation cost and shorter time for auditing when compared with conventional approaches. The results present that the proposed scheme is secure and efficient for cloud storage services managing dynamic shared data. PMID:24959630

A secure and efficient audit mechanism for dynamic shared data in cloud storage.

PubMed

Kwon, Ohmin; Koo, Dongyoung; Shin, Yongjoo; Yoon, Hyunsoo

2014-01-01

With popularization of cloud services, multiple users easily share and update their data through cloud storage. For data integrity and consistency in the cloud storage, the audit mechanisms were proposed. However, existing approaches have some security vulnerabilities and require a lot of computational overheads. This paper proposes a secure and efficient audit mechanism for dynamic shared data in cloud storage. The proposed scheme prevents a malicious cloud service provider from deceiving an auditor. Moreover, it devises a new index table management method and reduces the auditing cost by employing less complex operations. We prove the resistance against some attacks and show less computation cost and shorter time for auditing when compared with conventional approaches. The results present that the proposed scheme is secure and efficient for cloud storage services managing dynamic shared data.

7 CFR 46.20 - Lot numbers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Lot numbers. 46.20 Section 46.20 Agriculture... Receivers § 46.20 Lot numbers. An identifying lot number shall be assigned to each shipment of produce to be sold on consignment or joint account or for the account of another person or firm. A lot number should...

7 CFR 46.20 - Lot numbers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Lot numbers. 46.20 Section 46.20 Agriculture... Receivers § 46.20 Lot numbers. An identifying lot number shall be assigned to each shipment of produce to be sold on consignment or joint account or for the account of another person or firm. A lot number should...

7 CFR 46.20 - Lot numbers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Lot numbers. 46.20 Section 46.20 Agriculture... Receivers § 46.20 Lot numbers. An identifying lot number shall be assigned to each shipment of produce to be sold on consignment or joint account or for the account of another person or firm. A lot number should...

7 CFR 46.20 - Lot numbers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Lot numbers. 46.20 Section 46.20 Agriculture... Receivers § 46.20 Lot numbers. An identifying lot number shall be assigned to each shipment of produce to be sold on consignment or joint account or for the account of another person or firm. A lot number should...

7 CFR 46.20 - Lot numbers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Lot numbers. 46.20 Section 46.20 Agriculture... Receivers § 46.20 Lot numbers. An identifying lot number shall be assigned to each shipment of produce to be sold on consignment or joint account or for the account of another person or firm. A lot number should...

Small but Dynamic Active Region

NASA Image and Video Library

2018-04-20

The sun featured just one, rather small active region over the past few days, but it developed rapidly and sported a lot of magnetic activity in just one day (Apr. 11-12, 2018). The activity was observed in a wavelength of extreme ultraviolet light. The loops and twisting arches above it are evidence of magnetic forces tangling with each other. The video clip was produced using Helioviewer software. Movies are available at https://photojournal.jpl.nasa.gov/catalog/PIA06676

Wavelength Comparisons

NASA Image and Video Library

2018-04-02

NASA's Solar Dynamics Observatory ran together three sequences of the sun taken in three different extreme ultraviolet wavelengths to better illustrate how different features that appear in one sequence are difficult if not impossible to see in the others (Mar. 20-21, 2018). In the red sequence (304 Angstroms), we can see very small spicules and some small prominences at the sun's edge, which are not easy to see in the other two sequences. In the second clip (193 Angstroms), we can readily observe the large and dark coronal hole, though it is difficult to make out in the others. In the third clip (171 wavelengths), we can see strands of plasma waving above the surface, especially above the one small, but bright, active region near the right edge. And these are just three of the 10 extreme ultraviolet wavelengths in which SDO images the sun every 12 seconds every day. That's a lot of data and a lot of science. Movies are available at https://photojournal.jpl.nasa.gov/catalog/PIA22360

The dependence of the CO2 removal efficiency of LiOH on humidity and mesh size. [in spacecraft life support systems

NASA Technical Reports Server (NTRS)

Davis, S. H.; Kissinger, L. D.

1978-01-01

The effect of humidity on the CO2 removal efficiency of small beds of anhydrous LiOH has been studied. Experimental data taken in this small bed system clearly show that there is an optimum humidity for beds loaded with LiOH from a single lot. The CO2 efficiency falls rapidly under dry conditions, but this behavior is approximately the same in all samples. The behavior of the bed under wet conditions is quite dependent on material size distribution. The presence of large particles in a sample can lead to rapid fall off in the CO2 efficiency as the humidity increases.

An evaluation of trout culture

USGS Publications Warehouse

1940-01-01

In an evaluation of the efficiency of trout culture, the author presents a detailed analysis of complete loss records from 288 individual lots of trout at twenty-two hatcheries in the western United States. Summarized data are given to show the percentage loss of eggs, fry, and fingerlings by progressive one-half inch size groups. The accumulative percentage loss is also included to indicate the losses, under average hatchery conditions, between the egg stage and each successive size-group. These data cover the individual species of trout commonly reared in hatcheries; summarized data are given also for all species combined. A brief discussion of hatchery losses, natural losses, and the cost of artificial propagation is included.

78 FR 51742 - Notice of Proposed Withdrawal and Opportunity for Public Meeting; California

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

..., inclusive, and SE\\1/ 4\\NE\\1/4\\; sec. 26, lots 11, 12, and 13, S\\1/2\\SE\\1/4\\NE\\1/4\\, and N\\1/ 2\\NE\\1/4\\SE\\1/4..., lots 13 to 16, inclusive, and 18 to 22, inclusive, and a portion of lot 8 as described in the Donation... platted. sec. 19, lots 11, 13, and 16 to 19, inclusive; sec. 20, lot 4; sec. 29, lots 7 and 11; sec. 32...

Lot-to-lot consistency of a tetravalent dengue vaccine in healthy adults in Australia: a randomised study.

PubMed

Torresi, Joseph; Heron, Leon G; Qiao, Ming; Marjason, Joanne; Chambonneau, Laurent; Bouckenooghe, Alain; Boaz, Mark; van der Vliet, Diane; Wallace, Derek; Hutagalung, Yanee; Nissen, Michael D; Richmond, Peter C

2015-09-22

The recombinant yellow fever-17D-dengue virus, live, attenuated, tetravalent dengue vaccine (CYD-TDV) has undergone extensive clinical trials. Here safety and consistency of immunogenicity of phase III manufacturing lots of CYD-TDV were evaluated and compared with a phase II lot and placebo in a dengue-naïve population. Healthy 18-60 year-olds were randomly assigned in a 3:3:3:3:1 ratio to receive three subcutaneous doses of either CYD-TDV from any one of three phase III lots or a phase II lot, or placebo, respectively in a 0, 6, 12 month dosing schedule. Neutralising antibody geometric mean titres (PRNT50 GMTs) for each of the four dengue serotypes were compared in sera collected 28 days after the third vaccination-equivalence among lots was demonstrated if the lower and upper limits of the two-sided 95% CIs of the GMT ratio were ≥0.5 and ≤2.0, respectively. 712 participants received vaccine or placebo and 614 (86%) completed the study; 17 (2.4%) participants withdrew after adverse events. Equivalence of phase III lots was demonstrated for 11 of 12 pairwise comparisons. One of three comparisons for serotype 2 was not statistically equivalent. GMTs for serotype 2 in phase III lots were close to each other (65.9, 44.1 and 58.1, respectively). Phase III lots can be produced in a consistent manner with predictable immune response and acceptable safety profile similar to previously characterised phase II lots. The phase III lots may be considered as not clinically different as statistical equivalence was shown for serotypes 1, 3 and 4 across the phase III lots. For serotype 2, although equivalence was not shown between two lots, the GMTs observed in the phase III lots were consistently higher than those for the phase II lot. As such, in our view, biological equivalence for all serotypes was demonstrated. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

7 CFR 983.152 - Failed lots/rework procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Failed lots/rework procedure. 983.152 Section 983.152..., ARIZONA, AND NEW MEXICO Rules and Regulations § 983.152 Failed lots/rework procedure. (a) Inshell rework... the lot has been reworked and tested, it fails the aflatoxin test for a second time, the lot may be...

7 CFR 983.152 - Failed lots/rework procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Failed lots/rework procedure. 983.152 Section 983.152..., ARIZONA, AND NEW MEXICO Rules and Regulations § 983.152 Failed lots/rework procedure. (a) Inshell rework... the lot has been reworked and tested, it fails the aflatoxin test for a second time, the lot may be...

7 CFR 983.152 - Failed lots/rework procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Failed lots/rework procedure. 983.152 Section 983.152..., ARIZONA, AND NEW MEXICO Rules and Regulations § 983.152 Failed lots/rework procedure. (a) Inshell rework... the lot has been reworked and tested, it fails the aflatoxin test for a second time, the lot may be...

7 CFR 983.152 - Failed lots/rework procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Failed lots/rework procedure. 983.152 Section 983.152..., ARIZONA, AND NEW MEXICO Rules and Regulations § 983.152 Failed lots/rework procedure. (a) Inshell rework... the lot has been reworked and tested, it fails the aflatoxin test for a second time, the lot may be...

Three stage trade credit policy in a three-layer supply chain-a production-inventory model

NASA Astrophysics Data System (ADS)

Pal, Brojeswar; Sankar Sana, Shib; Chaudhuri, Kripasindhu

2014-09-01

The main purpose of this paper is to investigate the optimal replenishment lot size of supplier and optimal production rate of manufacturer under three levels of trade credit policy for supplier-manufacturer-retailer supply chain. The supplier provides a fixed credit period to settle the accounts to the manufacturer, while the manufacturer gives a fixed credit period to settle the account to the retailer and the retailer, in turn, also offers a credit period to each of its customers to settle the accounts. We assume that the supplier supplies the raw material to the manufacturer and sends back the defective raw materials to the outside supplier after completion of inspection at one lot with a sales price. The system always produces good items in the model. Also, we consider the idle times of supplier and manufacturer. Finally, numerical examples are provided to illustrate the behaviour and application of the model with graphical simulation.

Cluster designs to assess the prevalence of acute malnutrition by lot quality assurance sampling: a validation study by computer simulation

PubMed Central

Olives, Casey; Pagano, Marcello; Deitchler, Megan; Hedt, Bethany L; Egge, Kari; Valadez, Joseph J

2009-01-01

Traditional lot quality assurance sampling (LQAS) methods require simple random sampling to guarantee valid results. However, cluster sampling has been proposed to reduce the number of random starting points. This study uses simulations to examine the classification error of two such designs, a 67×3 (67 clusters of three observations) and a 33×6 (33 clusters of six observations) sampling scheme to assess the prevalence of global acute malnutrition (GAM). Further, we explore the use of a 67×3 sequential sampling scheme for LQAS classification of GAM prevalence. Results indicate that, for independent clusters with moderate intracluster correlation for the GAM outcome, the three sampling designs maintain approximate validity for LQAS analysis. Sequential sampling can substantially reduce the average sample size that is required for data collection. The presence of intercluster correlation can impact dramatically the classification error that is associated with LQAS analysis. PMID:20011037

Lot quality assurance sampling to monitor supplemental immunization activity quality: an essential tool for improving performance in polio endemic countries.

PubMed

Brown, Alexandra E; Okayasu, Hiromasa; Nzioki, Michael M; Wadood, Mufti Z; Chabot-Couture, Guillaume; Quddus, Arshad; Walker, George; Sutter, Roland W

2014-11-01

Monitoring the quality of supplementary immunization activities (SIAs) is a key tool for polio eradication. Regular monitoring data, however, are often unreliable, showing high coverage levels in virtually all areas, including those with ongoing virus circulation. To address this challenge, lot quality assurance sampling (LQAS) was introduced in 2009 as an additional tool to monitor SIA quality. Now used in 8 countries, LQAS provides a number of programmatic benefits: identifying areas of weak coverage quality with statistical reliability, differentiating areas of varying coverage with greater precision, and allowing for trend analysis of campaign quality. LQAS also accommodates changes to survey format, interpretation thresholds, evaluations of sample size, and data collection through mobile phones to improve timeliness of reporting and allow for visualization of campaign quality. LQAS becomes increasingly important to address remaining gaps in SIA quality and help focus resources on high-risk areas to prevent the continued transmission of wild poliovirus. © Crown copyright 2014.

Trypanosoma brucei gambiense trypanosomiasis in Terego county, northern Uganda, 1996: a lot quality assurance sampling survey.

PubMed

Hutin, Yvan J F; Legros, Dominique; Owini, Vincent; Brown, Vincent; Lee, Evan; Mbulamberi, Dawson; Paquet, Christophe

2004-04-01

We estimated the pre-intervention prevalence of Trypanosoma brucei gambiense (Tbg) trypanosomiasis using the lot quality assurance sampling (LQAS) methods in 14 parishes of Terego County in northern Uganda. A total of 826 participants were included in the survey sample in 1996. The prevalence of laboratory confirmed Tbg trypanosomiasis adjusted for parish population sizes was 2.2% (95% confidence interval =1.1-3.2). This estimate was consistent with the 1.1% period prevalence calculated on the basis of cases identified through passive and active screening in 1996-1999. Ranking of parishes in four categories according to LQAS analysis of the 1996 survey predicted the prevalences observed during the first round of active screening in the population in 1997-1998 (P < 0.0001, by chi-square test). Overall prevalence and ranking of parishes obtained with LQAS were validated by the results of the population screening, suggesting that these survey methods may be useful in the pre-intervention phase of sleeping sickness control programs.

From submarine to lacustrine groundwater discharge

USGS Publications Warehouse

Lewandowski, Jörg; Meinikmann, Karin; Pöschke, Franziska; Nützmann, Gunnar; Rosenberry, Donald O.

2017-01-01

Submarine groundwater discharge (SGD) and its role in marine nutrient cycling are well known since the last decade. The freshwater equivalent, lacustrine groundwater discharge (LGD), is often still disregarded, although first reports of LGD are more than 50 years old. We identify nine different reasons why groundwater has long been disregarded in both freshwater and marine environments such as invisibility of groundwater discharge, the size of the interface and its difficult accessibility. Although there are some fundamental differences in the hydrology of SGD and LGD, caused primarily by seawater recirculation that occurs only in cases of SGD, there are also a lot of similarities such as a focusing of discharge to near-shore areas. Nutrient concentrations in groundwater near the groundwater–surface water interface might be anthropogenically enriched. Due to spatial heterogeneity of aquifer characteristics and biogeochemical processes, the quantification of groundwater-borne nutrient loads is challenging. Both nitrogen and phosphorus might be mobile in near-shore aquifers and in a lot of case studies large groundwater-borne nutrient loads have been reported.

Network Flows

DTIC Science & Technology

1988-12-01

production or service activity over time. In these instances it is often convenient to formulate a network flow problem on a "space—time network" with several...planning model in production planning, the economic lot size problem, is an important example. In this problem context, we wish to meet prescribed...demands d^ for a product in each of the T time periods. In each period, we can produce at level Xj and /or we can meet the demand by drav^g upon inventory I

U.S. Africa Policy: Some Possible Course Adjustment

DTIC Science & Technology

1994-08-29

installations on behalf of an African Marxist government. A lot of Angola’s oil was exported to the United States; the U.S. companies involved made money. The...country, with major legitimate social service and infrastructure needs and, probably, very greedy leadership, would be able to forego exportation of its...droughts like the Sahel-and fully capable of feeding its population and producing for agricultural export . It has diamonds for ready cash. The size of

Diatom-Based Material Production Demonstration

DTIC Science & Technology

2016-03-14

Standard Form 298 (Rev 8/98) Prescribed by ANSI Std. Z39.18 Final Report W911NF-15-2-0012 66671-CH-DRP.5 808-212-4509 a. REPORT 14. ABSTRACT 16...diatomaceous earth. Diatomaceous earth consists of fossilized diatom cell walls, which have non uniform size with a lot of debris and a large...PROGRAM ELEMENT NUMBER 5b. GRANT NUMBER 5a. CONTRACT NUMBER Form Approved OMB NO. 0704-0188 3. DATES COVERED (From - To) - Approved for Public Release

Demonstration of Metastable Intermolecular Composites (MIC) on Small Caliber Cartridges and CAD/PAD Percussion Primers

DTIC Science & Technology

2009-07-01

BET, helium pycnometer, particle size laser scattering analysis, X-ray diffraction, TGA, DSC, calorimeter, etc.) • Initiated manufacturing of...boxes are then packed into a one-gallon aluminum paint can along with sufficient padding, after which the lid is installed in the usual manner. The... paint cans are stored for later use in a magazine without temperature and humidity control. In a typical lot of 10,000 primers, 900 are immediately

Effects of Leading Edge Defect on the Aerodynamic and Flow Characteristics of an S809 Airfoil

PubMed Central

Wang, Yan; Zheng, Xiaojing; Hu, Ruifeng; Wang, Ping

2016-01-01

Background Unexpected performance degradation occurs in wind turbine blades due to leading edge defect when suffering from continuous impacts with rain drops, hails, insects, or solid particles during its operation life. To assess this issue, this paper numerically investigates the steady and dynamic stall characteristics of an S809 airfoil with various leading edge defects. More leading edge defect sizes and much closer to practical parameters are investigated in the paper. Methodology Numerical computation is conducted using the SST k-ω turbulence model, and the method has been validated by comparison with existed published data. In order to ensure the calculation convergence, the residuals for the continuity equation are set to be less than 10−7 and 10−6 in steady state and dynamic stall cases. The simulations are conducted with the software ANSYS Fluent 13.0. Results It is found that the characteristics of aerodynamic coefficients and flow fields are sensitive to leading edge defect both in steady and dynamic conditions. For airfoils with the defect thickness of 6%tc, leading edge defect has a relative small influence on the aerodynamics of S809 airfoil. For other investigated defect thicknesses, leading edge defect has much greater influence on the flow field structures, pressure coefficients and aerodynamic characteristics of airfoil at relative small defect lengths. For example, the lift coefficients decrease and drag coefficients increase sharply after the appearance of leading edge defect. However, the aerodynamic characteristics could reach a constant value when the defect length is large enough. The flow field, pressure coefficient distribution and aerodynamic coefficients do not change a lot when the defect lengths reach to 0.5%c,1%c, 2%c and 3%c with defect thicknesses of 6%tc, 12%tc,18%tc and 25%tc, respectively. In addition, the results also show that the critical defect length/thickness ratio is 0.5, beyond which the aerodynamic characteristics nearly remain unchanged. In dynamic stall, leading edge defect imposes a greater influence on the aerodynamic characteristics of airfoil than steady conditions. By increasing in defect length, it is found that the separated area becomes more intense and moves forward along the suction surface. Conclusions Leading edge defect has significant influence on the aerodynamic and flow characteristics of the airfoil, which will reach a stable status with enough large defect size. The leading edge separation bubble, circulation in the defect cavity and intense tailing edge vortex are the main features of flow around defective airfoils. PMID:27658310

Effects of Leading Edge Defect on the Aerodynamic and Flow Characteristics of an S809 Airfoil.

PubMed

Wang, Yan; Zheng, Xiaojing; Hu, Ruifeng; Wang, Ping

Unexpected performance degradation occurs in wind turbine blades due to leading edge defect when suffering from continuous impacts with rain drops, hails, insects, or solid particles during its operation life. To assess this issue, this paper numerically investigates the steady and dynamic stall characteristics of an S809 airfoil with various leading edge defects. More leading edge defect sizes and much closer to practical parameters are investigated in the paper. Numerical computation is conducted using the SST k-ω turbulence model, and the method has been validated by comparison with existed published data. In order to ensure the calculation convergence, the residuals for the continuity equation are set to be less than 10-7 and 10-6 in steady state and dynamic stall cases. The simulations are conducted with the software ANSYS Fluent 13.0. It is found that the characteristics of aerodynamic coefficients and flow fields are sensitive to leading edge defect both in steady and dynamic conditions. For airfoils with the defect thickness of 6%tc, leading edge defect has a relative small influence on the aerodynamics of S809 airfoil. For other investigated defect thicknesses, leading edge defect has much greater influence on the flow field structures, pressure coefficients and aerodynamic characteristics of airfoil at relative small defect lengths. For example, the lift coefficients decrease and drag coefficients increase sharply after the appearance of leading edge defect. However, the aerodynamic characteristics could reach a constant value when the defect length is large enough. The flow field, pressure coefficient distribution and aerodynamic coefficients do not change a lot when the defect lengths reach to 0.5%c,1%c, 2%c and 3%c with defect thicknesses of 6%tc, 12%tc,18%tc and 25%tc, respectively. In addition, the results also show that the critical defect length/thickness ratio is 0.5, beyond which the aerodynamic characteristics nearly remain unchanged. In dynamic stall, leading edge defect imposes a greater influence on the aerodynamic characteristics of airfoil than steady conditions. By increasing in defect length, it is found that the separated area becomes more intense and moves forward along the suction surface. Leading edge defect has significant influence on the aerodynamic and flow characteristics of the airfoil, which will reach a stable status with enough large defect size. The leading edge separation bubble, circulation in the defect cavity and intense tailing edge vortex are the main features of flow around defective airfoils.

76 FR 72469 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-23

...-lot'' order is an order for a quantity that is less than 100. A ``mixed-lot'' order is an order for a... mixed-lot order) are processed in the same manner as are round-lot orders, except (i) If an incoming odd... mixed-lot orders of HOLDRS in accordance with Rule 52.8, as described above. However, the prospectuses...

Can “Cleaned and Greened” Lots Take on the Role of Public Greenspace?

Treesearch

Megan Heckert; Michelle Kondo

2018-01-01

Cities are increasingly greening vacant lots to reduce blight. Such programs could reduce inequities in urban greenspace access, but whether and how greened lots are used remains unclear. We surveyed three hundred greened lots in Philadelphia for signs of use and compared characteristics of used and nonused lots. We found physical signs of use that might be found in...

Multiple category-lot quality assurance sampling: a new classification system with application to schistosomiasis control.

PubMed

Olives, Casey; Valadez, Joseph J; Brooker, Simon J; Pagano, Marcello

2012-01-01

Originally a binary classifier, Lot Quality Assurance Sampling (LQAS) has proven to be a useful tool for classification of the prevalence of Schistosoma mansoni into multiple categories (≤10%, >10 and <50%, ≥50%), and semi-curtailed sampling has been shown to effectively reduce the number of observations needed to reach a decision. To date the statistical underpinnings for Multiple Category-LQAS (MC-LQAS) have not received full treatment. We explore the analytical properties of MC-LQAS, and validate its use for the classification of S. mansoni prevalence in multiple settings in East Africa. We outline MC-LQAS design principles and formulae for operating characteristic curves. In addition, we derive the average sample number for MC-LQAS when utilizing semi-curtailed sampling and introduce curtailed sampling in this setting. We also assess the performance of MC-LQAS designs with maximum sample sizes of n=15 and n=25 via a weighted kappa-statistic using S. mansoni data collected in 388 schools from four studies in East Africa. Overall performance of MC-LQAS classification was high (kappa-statistic of 0.87). In three of the studies, the kappa-statistic for a design with n=15 was greater than 0.75. In the fourth study, where these designs performed poorly (kappa-statistic less than 0.50), the majority of observations fell in regions where potential error is known to be high. Employment of semi-curtailed and curtailed sampling further reduced the sample size by as many as 0.5 and 3.5 observations per school, respectively, without increasing classification error. This work provides the needed analytics to understand the properties of MC-LQAS for assessing the prevalance of S. mansoni and shows that in most settings a sample size of 15 children provides a reliable classification of schools.

Water absorption and method improvement concerning electrical conductivity testing Acacia mangium (Fabaceae) seeds.

PubMed

de Oliveira, Daniel Luiz; Smiderle, Oscar Jose; Paulino, Pollyana Priscila Schuertz; Souza, Aline das Graças

2016-12-01

Acacia is an important forest species of rapid growth whose seeds have tegument dormancy. In this work it was intended to characterize water absorption pattern after seed dormancy break, and to determine the amount of water, container size and the need of breaking the tegument dormancy, as to perform electrical conductivity test in small and large seeds of Acacia mangium (Fabaceae). The seeds were collected from 10, 8 and 6 years old trees established in poor yielding-capacity soils on savannah areas of Roraima, Brazil; seeds were classified in six lots concerning to seed size and tree age. Germination tests (50 seeds and four replications per lot) were carried out on germitest® paper maintained on gerbox at 25 °C. Imbibition was verified by seed weighing at different times (0, 2, 5, 8, 12, 16, 24, 36, 48, 60, 72, 84, 96 and 120 hours). The electrical conductivity test consisted of three experiments, distinguished by the amount of water used and by the container size in which seeds were immersed. Seeds of A. mangium coming from 10 years old trees presented increased germination percent and germination speed than seeds of six-year old trees. Small seeds presented increased in electrical conductivity and water absorption until 120 hours when compared to large seeds. The immersion of seeds of A. mangium in 40 mL of distilled water into 180 mL plastic containers, after dormancy break, it is indicated for the determination of electrical conductivity test. The ratio of electrolytes by seed mass, after 24 hours of immersion in water, turns electrical conductivity test more accurate concerning A. mangium seeds.

12 CFR 1011.20 - Unlawful sales practices-regulatory provisions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... lot is suitable for a septic tank operation or there is reasonable assurance that the lot can be served by a central sewage system; (3) The lot is legally accessible; and (4) The lot is free from...

12 CFR 1011.20 - Unlawful sales practices-regulatory provisions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... lot is suitable for a septic tank operation or there is reasonable assurance that the lot can be served by a central sewage system; (3) The lot is legally accessible; and (4) The lot is free from...

12 CFR 1011.20 - Unlawful sales practices-regulatory provisions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... lot is suitable for a septic tank operation or there is reasonable assurance that the lot can be served by a central sewage system; (3) The lot is legally accessible; and (4) The lot is free from...

Asteroids in three-body mean motion resonances with planets

NASA Astrophysics Data System (ADS)

Smirnov, Evgeny A.; Dovgalev, Ilya S.; Popova, Elena A.

2018-04-01

We have identified all asteroids in three-body mean-motion resonances in all possible planets configurations. The identification was done dynamically: the orbits of the asteroids were integrated for 100,000 yrs and the set of the resonant arguments was numerically analyzed. We have found that each possible planets configuration has a lot of the resonant asteroids. In total 65,972 resonant asteroids (≈14.1% of the total number of 467,303 objects from AstDyS database) have been identified.

Technologies and problems of reengineering of the business processes of company

NASA Astrophysics Data System (ADS)

Silka, Dmitriy

2017-10-01

Management of the combination of business processes is a modern approach in the field of business management. Together with a lot of management approaches business processes allow us to identify all the resultant actions. Article reveals the modern view on the essence of business processes as well as the general approaches of their allocation. Principles of construction and business process re-engineering are proposed. Recommendations on how to perform re-engineering under high cyclic dynamics of business activity are provided.

Statistical assessment of DNA extraction reagent lot variability in real-time quantitative PCR

USGS Publications Warehouse

Bushon, R.N.; Kephart, C.M.; Koltun, G.F.; Francy, D.S.; Schaefer, F. W.; Lindquist, H.D. Alan

2010-01-01

Aims: The aim of this study was to evaluate the variability in lots of a DNA extraction kit using real-time PCR assays for Bacillus anthracis, Francisella tularensis and Vibrio cholerae. Methods and Results: Replicate aliquots of three bacteria were processed in duplicate with three different lots of a commercial DNA extraction kit. This experiment was repeated in triplicate. Results showed that cycle threshold values were statistically different among the different lots. Conclusions: Differences in DNA extraction reagent lots were found to be a significant source of variability for qPCR results. Steps should be taken to ensure the quality and consistency of reagents. Minimally, we propose that standard curves should be constructed for each new lot of extraction reagents, so that lot-to-lot variation is accounted for in data interpretation. Significance and Impact of the Study: This study highlights the importance of evaluating variability in DNA extraction procedures, especially when different reagent lots are used. Consideration of this variability in data interpretation should be an integral part of studies investigating environmental samples with unknown concentrations of organisms. ?? 2010 The Society for Applied Microbiology.

Exploring reserve lots of Cymbopogon citratus, Aloysia citrodora and Thymus × citriodorus as improved sources of phenolic compounds.

PubMed

Rita, Ingride; Pereira, Carla; Barros, Lillian; Ferreira, Isabel C F R

2018-08-15

Given the increasing consumers demand for novelty, tea companies have been presenting new added value products such as reserve lots of aromatic plants. Herein, infusions from different lots of three aromatic plants were assessed in terms of phenolic composition (HPLC-DAD-ESI/MS) and antioxidant properties (reducing power, free radical scavenging and lipid peroxidation inhibition capacity). Cymbopogon citratus (C. citratus; main compound 5-O-caffeoylquinic acid) and Aloysia citrodora (A. citrodora; prevalence of verbascoside) reserve lots revealed higher phenolic compounds concentration than the respective standard lots. Thymus × citriodorus (T. citriodorus; main compound rosmarinic acid) standard lot presented higher amounts of phenolic acids than the reserve lot, nonetheless, total flavonoids and phenolic compounds were not significantly different. The differences between both lots antioxidant activity were more noticeable in C. citratus, with the reserve lot presenting the highest activity. This study provides evidence of the differences between these plants chemical composition and bioactivity depending on the harvesting conditions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Towards Cluster-Assembled Materials of True Monodispersity in Size and Chemical Environment: Synthesis, Dynamics and Activity

DTIC Science & Technology

2016-10-27

AFRL-AFOSR-UK-TR-2016-0037 Towards cluster-assembled materials of true monodispersity in size and chemical environment: Synthesis, Dynamics and...Towards cluster-assembled materials of true monodispersity in size and chemical environment: synthesis, dynamics and activity 5a.  CONTRACT NUMBER 5b...report Towards cluster-assembled materials of true monodispersity in size and chemical environment: Synthesis, Dynamics and Activity Ulrich Heiz

Modeling the "Year without summer 1816" with the CCM SOCOL

NASA Astrophysics Data System (ADS)

Arfeuille, Florian; Rozanov, Eugene; Peter, Thomas; Fischer, Andreas. M.; Weisenstein, Debra; Brönnimann, Stefan

2010-05-01

The "Year without summer" 1816 had profound social and environmental effects, and although the cataclysmic eruption of Mt Tambora is now commonly known to have largely contributed to the negative temperature anomalies of the summer 1816 in Europe and North America, lots of uncertainties remain. The eruption of Mt. Tambora in April 1815 is the largest within the last 500 years. A crucial parameter to assess in order to simulate this eruption is the aerosol size distribution, which strongly influences the radiative impact of the aerosols (changes in albedo and residence time in the stratosphere, among others) and the impacts on dynamics and chemistry. The representation of this major forcing is done by using the AER-2D aerosol model which calculates the size distribution of the aerosols formed after the eruption. The modeling of the climatic impacts is then done by the state-of-the-art Chemistry-Climate model (CCM) SOCOL. The importance of stratospheric processes for the study of the "Year without summer" 1816 justifies the choice of a CCM which allows a precise analysis of the radiative, dynamical and chemical impacts of the Tambora eruption. The 1810's decade is an interesting period as it combines both a strong signal to noise ratio for the study of the impacts of the volcanic forcing, and an availability of several high resolution climate proxies allowing a credible reconstruction of interesting climatic components like Sea Surface Temperatures (SST) which are forced in the CCM . This can particularly provide a realistic description of the inter-annual variability linked to the major atmosphere/ocean coupled oscillations such as ENSO. Reconstructions based on inland natural proxies and early instrumental records can then be used to validate the simulated climate. I will present the characteristics of the Tambora eruption and show some results from simulations made using the aerosol model/CCM, with an emphasis on the radiative and chemical implications of the large aerosol sizes produced by the Mt. Tambora 60-80MT SO2 release. For instance, the specific absorption/scattering ratio of Mt.Tambora aerosols induced a very large stratospheric warming which will be analyzed. The climatic impacts will also be discussed in regards of the high sedimentation rate of Mt. Tambora aerosols, leading to a fast decrease of the atmospheric optical depth in the first two years after the eruption.

Joint-use park-and-ride lots.

DOT National Transportation Integrated Search

1989-01-01

Joint-use park-and-ride lots have proven successful in Virginia as well as other states. As expected, there are both positive and negative aspects of such lots; these are described in this report. In addition, information on incentives to lot owners,...

Evaluation of lot-to-lot repeatability and effect of assay media choice in the recombinant Factor C assay.

PubMed

McKenzie, Jennifer Helen; Alwis, K Udeni; Sordillo, Joanne E; Kalluri, Kesava Srinivas; Milton, Donald Kirby

2011-06-01

Measurement of environmental endotoxin exposures is complicated by variability encountered using current biological assay methods arising in part from lot-to-lot variability of the Limulus-amebocyte lysate (LAL) reagents. Therefore, we investigated the lot-to-lot repeatability of commercially available recombinant Factor C (rFC) kits as an alternative to LAL. Specifically, we compared endotoxin estimates obtained from rFC assay of twenty indoor dust samples, using four different extraction and assay media, to endotoxin estimates previously obtained by Limulus amebocyte lysate (LAL) assay and amounts of 3-hydroxy fatty acids (3-OHFA) in lipopolysaccharide (LPS) using gas-chromatography mass spectroscopy (GC-MS). We found that lot-to-lot variability of the rFC assay kits does not significantly alter endotoxin estimates in house dust samples when performed using three of the four assay media tested and that choice of assay media significantly altered endotoxin estimates obtained by rFC assay of house dust samples. Our findings demonstrate lot-to-lot reproducibility of rFC assay of environmental samples and suggest that use of rFC assay performed with Tris buffer or water as the extraction and assay medium for measurement of endotoxin in dust samples may be a suitable choice for developing a standardized methodology.

On the role of quantum ion dynamics for the anomalous melting of lithium

NASA Astrophysics Data System (ADS)

Elatresh, Sabri; Bonev, Stanimir

2011-03-01

Lithium has attracted a lot of interest in relation to a number of counterintuitive electronic and structural changes that it exhibits under pressure. One of the most remarkable properties of dense lithium is its anomalous melting. This behavior was first predicted theoretically based on first-principles molecular dynamics (FPMD) simulations, which treated the ions classically. The lowest melting temperature was determined to be about 275~K at 65~GPa. Recent experiments measured a melting temperature about 100~K lower at the same pressure. In this talk, we will present FPMD calculations of solid and liquid lithium free energies up to 100 GPa that take into account ion quantum dynamics. We examine the significance of the quantum effects for the finite-temperature phase boundaries of lithium and, in particular, its melting curve. Work supported by NSERC, Acenet, and LLNL under Contract DE-AC52-07NA27344.

Prediction of mass transfer coefficient in rotating bed contactor (Higee) using artificial neural network

NASA Astrophysics Data System (ADS)

Saha, Dipendu

2009-02-01

The feasibility of drastically reducing the contactor size in mass transfer processes utilizing centrifugal field has generated a lot of interest in rotating packed bed (Higee). Various investigators have proposed correlations to predict mass transfer coefficients in Higee, but, none of the correlations was more than 20-30% accurate. In this work, artificial neural network (ANN) is employed for predicting mass transfer coefficient data. Results show that ANN provides better estimation of mass transfer coefficient with accuracy 5-15%.

Fun and games in Berkeley: the early years (1956-2013).

PubMed

Tinoco, Ignacio

2014-01-01

Life at Berkeley for the past 57 years involved research on the thermodynamics, kinetics, and spectroscopic properties of RNA to better understand its structures, interactions, and functions. We (myself and all the graduate students and postdocs who shared in the fun) began with dinucleoside phosphates and slowly worked our way up to megadalton-sized RNA molecular motors. We used UV absorption, circular dichroism, circular intensity differential scattering, fluorescence, NMR, and single-molecule methods. We learned a lot and had fun doing it.

Evaluation of some selected vaccines and other biological products irradiated by gamma rays, electron beams and X-rays

NASA Astrophysics Data System (ADS)

May, J. C.; Rey, L.; Lee, Chi-Jen

2002-03-01

Molecular sizing potency results are presented for irradiated samples of one lot of Haemophilus b conjugate vaccine, pneumococcal polysaccharide type 6B and typhoid vi polysaccharide vaccine. The samples were irradiated (25 kGy) by gamma rays, electron beams and X-rays. IgG and IgM antibody response in mice test results (ELISA) are given for the Hib conjugate vaccine irradiated at 0°C or frozen in liquid nitrogen.

Pavement Maintenance Management for Roads and Parking Lots.

DTIC Science & Technology

1981-10-01

PAVEMENT INSPECTION SHEET aRANCH SECT ION DA TE SAMPLE UNIT SURVEYED BY SLAB SIZE * 0 0 0 Distress Types !0 2f Blow- Up 3’ Polished Buckling/Shattering...10 21 Blow- up 31 Poisnec Buckling/Shatternrg Aggregate 0 1 22. Corner Break 32 Porouis 23. D’viOea SIcD 33 Ptmo,nq 9 24 Durability . " 34 Pancnout...Load Durability Drainage Other Factors Corner Break Blow- up Corner Break Faulting Divided Slab Ŕ" Cracking Divided Slab Lane/Shoulder Dropoff

Global Power Requires a Global, Persistent Air-to-Air Capability

DTIC Science & Technology

2010-01-01

anywhere on the high seas, and in most coastal waters as well, and sink them if necessary by using guns, missiles, or tor- pedoes . Current Air Force...apparently a number of so-far-undisclosed challenges remain, perhaps including the air refuel- ing of an RPA and maintaining the data link with it in...will remain relatively short- range systems.31 With regard to the data link , a remote pi- lot flies the Predator—our primary opera- tional, fighter-sized

Lie symmetry analysis, conservation laws, solitary and periodic waves for a coupled Burger equation

NASA Astrophysics Data System (ADS)

Xu, Mei-Juan; Tian, Shou-Fu; Tu, Jian-Min; Zhang, Tian-Tian

2017-01-01

Under investigation in this paper is a generalized (2 + 1)-dimensional coupled Burger equation with variable coefficients, which describes lots of nonlinear physical phenomena in geophysical fluid dynamics, condense matter physics and lattice dynamics. By employing the Lie group method, the symmetry reductions and exact explicit solutions are obtained, respectively. Based on a direct method, the conservations laws of the equation are also derived. Furthermore, by virtue of the Painlevé analysis, we successfully obtain the integrable condition on the variable coefficients, which plays an important role in further studying the integrability of the equation. Finally, its auto-Bäcklund transformation as well as some new analytic solutions including solitary and periodic waves are also presented via algebraic and differential manipulation.

Lot-to-Lot Variability of Test Strips and Accuracy Assessment of Systems for Self-Monitoring of Blood Glucose according to ISO 15197

PubMed Central

Baumstark, Annette; Pleus, Stefan; Schmid, Christina; Link, Manuela; Haug, Cornelia; Freckmann, Guido

2012-01-01

Background Accurate and reliable blood glucose (BG) measurements require that different test strip lots of the same BG monitoring system provide comparable measurement results. Only a small number of studies addressing this question have been published. Methods In this study, four test strip lots for each of five different BG systems [Accu-Chek® Aviva (system A), FreeStyle Lite® (system B), GlucoCheck XL (system C), Pura™/mylife™ Pura (system D), and OneTouch® Verio™ Pro (system E)] were evaluated with procedures according to DIN EN ISO 15197:2003. The BG system measurement results were compared with the manufacturer’s measurement procedure (glucose oxidase or hexokinase method). Relative bias according to Bland and Altman and system accuracy according to ISO 15197 were analyzed. A BG system consists of the BG meter itself and the test strips. Results The maximum lot-to-lot difference between any two of the four evaluated test strip lots per BG system was 1.0% for system E, 2.1% for system A, 3.1% for system C, 6.9% for system B, and 13.0% for system D. Only two systems (systems A and B) fulfill the criteria of DIN EN ISO 15197:2003 with each test strip lot. Conclusions Considerable lot-to-lot variability between test strip lots of the same BG system was found. These variations add to other sources of inaccuracy with the specific BG system. Manufacturers should regularly and effectively check the accuracy of their BG meters and test strips even between different test strip lots to minimize risk of false treatment decisions. PMID:23063033

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and major and trace elements in simulated rainfall runoff from parking lots, Austin, Texas, 2003

USGS Publications Warehouse

Mahler, Barbara J.; Van Metre, Peter C.; Wilson, Jennifer T.

2004-01-01

Samples of creek bed sediment collected near seal-coated parking lots in Austin, Texas, by the City of Austin during 2001–02 had unusually elevated concentrations of polycyclic aromatic hydrocarbons (PAHs). To investigate the possibility that PAHs from seal-coated parking lots might be transported to urban creeks, the U.S. Geological Survey, in cooperation with the City of Austin, sampled runoff and scrapings from four test plots and 13 urban parking lots. The surfaces sampled comprise coal-tar-emulsion-sealed, asphalt-emulsion-sealed, unsealed asphalt, and unsealed concrete. Particulates and filtered water in runoff and surface scrapings were analyzed for PAHs. In addition, particulates in runoff were analyzed for major and trace elements. Samples of all three media from coal-tar-sealed parking lots had concentrations of PAHs higher than those from any other types of surface. The mean total PAH concentration in particulates in runoff from parking lots in use were 3,500,000, 620,000, and 54,000 micrograms per kilogram from coal-tar-sealed, asphalt-sealed, and unsealed (asphalt and concrete combined) lots, respectively. The probable effect concentration sediment quality guideline is 22,800 micrograms per kilogram. The mean total PAH (sum of detected PAHs) concentration in filtered water from parking lots in use was 8.6 micrograms per liter for coal-tar-sealed lots; the one sample analyzed from an asphalt-sealed lot had a concentration of 5.1 micrograms per liter and the one sample analyzed from an unsealed asphalt lot was 0.24 microgram per liter. The mean total PAH concentration in scrapings was 23,000,000, 820,000, and 14,000 micrograms per kilogram from coal-tar-sealed, asphalt-sealed, and unsealed asphalt lots, respectively. Concentrations of lead and zinc in particulates in runoff frequently exceeded the probable effect concentrations, but trace element concentrations showed no consistent variation with parking lot surface type.

Pedestrian and traffic safety in parking lots at SNL/NM : audit background report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez, Paul Ernest

2009-03-01

This report supplements audit 2008-E-0009, conducted by the ES&H, Quality, Safeguards & Security Audits Department, 12870, during fall and winter of FY 2008. The study evaluates slips, trips and falls, the leading cause of reportable injuries at Sandia. In 2007, almost half of over 100 of such incidents occurred in parking lots. During the course of the audit, over 5000 observations were collected in 10 parking lots across SNL/NM. Based on benchmarks and trends of pedestrian behavior, the report proposes pedestrian-friendly features and attributes to improve pedestrian safety in parking lots. Less safe pedestrian behavior is associated with older parkingmore » lots lacking pedestrian-friendly features and attributes, like those for buildings 823, 887 and 811. Conversely, safer pedestrian behavior is associated with newer parking lots that have designated walkways, intra-lot walkways and sidewalks. Observations also revealed that motorists are in widespread noncompliance with parking lot speed limits and stop signs and markers.« less

Heuristic for Critical Machine Based a Lot Streaming for Two-Stage Hybrid Production Environment

NASA Astrophysics Data System (ADS)

Vivek, P.; Saravanan, R.; Chandrasekaran, M.; Pugazhenthi, R.

2017-03-01

Lot streaming in Hybrid flowshop [HFS] is encountered in many real world problems. This paper deals with a heuristic approach for Lot streaming based on critical machine consideration for a two stage Hybrid Flowshop. The first stage has two identical parallel machines and the second stage has only one machine. In the second stage machine is considered as a critical by valid reasons these kind of problems is known as NP hard. A mathematical model developed for the selected problem. The simulation modelling and analysis were carried out in Extend V6 software. The heuristic developed for obtaining optimal lot streaming schedule. The eleven cases of lot streaming were considered. The proposed heuristic was verified and validated by real time simulation experiments. All possible lot streaming strategies and possible sequence under each lot streaming strategy were simulated and examined. The heuristic consistently yielded optimal schedule consistently in all eleven cases. The identification procedure for select best lot streaming strategy was suggested.

Cluster lot quality assurance sampling: effect of increasing the number of clusters on classification precision and operational feasibility.

PubMed

Okayasu, Hiromasa; Brown, Alexandra E; Nzioki, Michael M; Gasasira, Alex N; Takane, Marina; Mkanda, Pascal; Wassilak, Steven G F; Sutter, Roland W

2014-11-01

To assess the quality of supplementary immunization activities (SIAs), the Global Polio Eradication Initiative (GPEI) has used cluster lot quality assurance sampling (C-LQAS) methods since 2009. However, since the inception of C-LQAS, questions have been raised about the optimal balance between operational feasibility and precision of classification of lots to identify areas with low SIA quality that require corrective programmatic action. To determine if an increased precision in classification would result in differential programmatic decision making, we conducted a pilot evaluation in 4 local government areas (LGAs) in Nigeria with an expanded LQAS sample size of 16 clusters (instead of the standard 6 clusters) of 10 subjects each. The results showed greater heterogeneity between clusters than the assumed standard deviation of 10%, ranging from 12% to 23%. Comparing the distribution of 4-outcome classifications obtained from all possible combinations of 6-cluster subsamples to the observed classification of the 16-cluster sample, we obtained an exact match in classification in 56% to 85% of instances. We concluded that the 6-cluster C-LQAS provides acceptable classification precision for programmatic action. Considering the greater resources required to implement an expanded C-LQAS, the improvement in precision was deemed insufficient to warrant the effort. Published by Oxford University Press on behalf of the Infectious Diseases Society of America 2014. This work is written by (a) US Government employee(s) and is in the public domain in the US.

Genetic stability of a dengue vaccine based on chimeric yellow fever/dengue viruses.

PubMed

Mantel, N; Girerd, Y; Geny, C; Bernard, I; Pontvianne, J; Lang, J; Barban, V

2011-09-02

A tetravalent dengue vaccine based on four live, attenuated, chimeric viruses (CYD1-4), constructed by replacing the genes coding for premembrane (prM) and envelope (E) proteins of the yellow fever (YF)-17D vaccine strain with those of the four serotypes of dengue virus, is in clinical phase III evaluation. We assessed the vaccine's genetic stability by fully sequencing each vaccine virus throughout the development and manufacturing process. The four viruses displayed complete genetic stability, with no change from premaster seed lots to bulk lots. When pursuing the virus growth beyond bulk lots, a few genetic variations were observed. Usually both the initial nucleotide and the new one persisted, and mutations appeared after a relatively high number of virus duplication cycles (65-200, depending on position). Variations were concentrated in the prM-E and non-structural (NS)4B regions. PrM-E variations had no impact on lysis-plaque size or neurovirulence in mice. None of the variations located in the YF-17D-derived genes corresponded with reversion to the wild-type Yellow Fever sequence. Variations in NS4B likely reflect virus adaptation to Vero cells growth. A low to undetectable viremia has been reported previously [1-3] in vaccinated non-human and human primates. Combined with the data reported here about the genetic stability of the vaccine strains, the probability of in vivo emergence of mutant viruses appears very low. Copyright © 2011 Elsevier Ltd. All rights reserved.

An efficient and provable secure revocable identity-based encryption scheme.

PubMed

Wang, Changji; Li, Yuan; Xia, Xiaonan; Zheng, Kangjia

2014-01-01

Revocation functionality is necessary and crucial to identity-based cryptosystems. Revocable identity-based encryption (RIBE) has attracted a lot of attention in recent years, many RIBE schemes have been proposed in the literature but shown to be either insecure or inefficient. In this paper, we propose a new scalable RIBE scheme with decryption key exposure resilience by combining Lewko and Waters' identity-based encryption scheme and complete subtree method, and prove our RIBE scheme to be semantically secure using dual system encryption methodology. Compared to existing scalable and semantically secure RIBE schemes, our proposed RIBE scheme is more efficient in term of ciphertext size, public parameters size and decryption cost at price of a little looser security reduction. To the best of our knowledge, this is the first construction of scalable and semantically secure RIBE scheme with constant size public system parameters.

Lot sizing and unequal-sized shipment policy for an integrated production-inventory system

NASA Astrophysics Data System (ADS)

Giri, B. C.; Sharma, S.

2014-05-01

This article develops a single-manufacturer single-retailer production-inventory model in which the manufacturer delivers the retailer's ordered quantity in unequal shipments. The manufacturer's production process is imperfect and it may produce some defective items during a production run. The retailer performs a screening process immediately after receiving the order from the manufacturer. The expected average total cost of the integrated production-inventory system is derived using renewal theory and a solution procedure is suggested to determine the optimal production and shipment policy. An extensive numerical study based on different sets of parameter values is conducted and the optimal results so obtained are analysed to examine the relative performance of the models under equal and unequal shipment policies.

Single-axis four-mirror system: large spherical primary and small fields

NASA Astrophysics Data System (ADS)

Baranne, Andre

1998-08-01

A catoptric corrector of modest size can be used for large spherical primaries, easily integrated at the prime focus, this corrector gives back to the system, aspect and properties of 2-mirrors classical telescopes. In the last few years, progress in active and adaptative optics makes possible a lot of things, progress in measuring distances, new ideas on optical coatings, new materials and so on in a near future, all that makes the instrumentalist dreamy It is said that nobody knows today if the size of 3rd millennium telescopes will be limited or not by a theoretical, physical or technical phenomenon, thus let us imagine but with thoughtfulness because our projects will be surely restricted by financial considerations

7 CFR 983.52 - Failed lots/rework procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Failed lots/rework procedure. 983.52 Section 983.52..., ARIZONA, AND NEW MEXICO Regulations § 983.52 Failed lots/rework procedure. (a) Substandard pistachios... committee may establish, with the Secretary's approval, appropriate rework procedures. (b) Failed lot...

7 CFR 983.52 - Failed lots/rework procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Failed lots/rework procedure. 983.52 Section 983.52..., ARIZONA, AND NEW MEXICO Regulations § 983.52 Failed lots/rework procedure. (a) Substandard pistachios... committee may establish, with the Secretary's approval, appropriate rework procedures. (b) Failed lot...

7 CFR 983.52 - Failed lots/rework procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Failed lots/rework procedure. 983.52 Section 983.52..., ARIZONA, AND NEW MEXICO Regulations § 983.52 Failed lots/rework procedure. (a) Substandard pistachios... committee may establish, with the Secretary's approval, appropriate rework procedures. (b) Failed lot...

7 CFR 29.35 - Lot seal.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Lot seal. 29.35 Section 29.35 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Regulations Definitions § 29.35 Lot seal. A seal approved by the Director for sealing lots of...

7 CFR 29.35 - Lot seal.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Lot seal. 29.35 Section 29.35 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Regulations Definitions § 29.35 Lot seal. A seal approved by the Director for sealing lots of...

Chemical analysis of DC745 Materials: DEV Lot 1 reinvestigation; barcodes P053387, P053388, and P053389

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dirmyer, Matthew R.

This report serves as a follow up to our initial development lot 1 chemical analysis report (LA-UR-16-21970). The purpose of that report was to determine whether or not certain combinations of resin lots and curing agent lots resulted in chemical differences in the final material. One finding of that report suggested that pad P053389 was different from the three other pads analyzed. This report consists of chemical analysis of P053387, P053388, and a reinvestigation of P053389 all of which came from the potentially suspect combination of resin and curing agents lot. The goal of this report is to determine whethermore » the observations relating to P053389 were isolated to that particular pad or systemic to that combination of resin and curing agent lot. The following suite of analyses were performed on the pads: Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Fourier Transform Infrared Spectroscopy (FT-IR), and Solid State Nuclear Magnetic Resonance (NMR). The overall conclusions of the study are that pads P053387 and P053388 behave more consistently with the pads of other resin lot and curing agent lot combinations and that the chemical observations made regarding pad P053389 are isolated to that pad and not representative of an issue with that resin lot and curing agent lot combination.« less

The Importance of Reagent Lot Registration in External Quality Assurance/Proficiency Testing Schemes.

PubMed

Stavelin, Anne; Riksheim, Berit Oddny; Christensen, Nina Gade; Sandberg, Sverre

2016-05-01

Providers of external quality assurance (EQA)/proficiency testing schemes have traditionally focused on evaluation of measurement procedures and participant performance and little attention has been given to reagent lot variation. The aim of the present study was to show the importance of reagent lot registration and evaluation in EQA schemes. Results from the Noklus (Norwegian Quality Improvement of Primary Care Laboratories) urine albumin/creatinine ratio (ACR) and prothrombin time international normalized ratio (INR) point-of-care EQA schemes from 2009-2015 were used as examples in this study. The between-participant CV for Afinion ACR increased from 6%-7% to 11% in 3 consecutive surveys. This increase was caused by differences between albumin reagent lots that were also observed when fresh urine samples were used. For the INR scheme, the CoaguChek INR results increased with the production date of the reagent lots, with reagent lot medians increasing from 2.0 to 2.5 INR and from 2.7 to 3.3 INR (from the oldest to the newest reagent lot) for 2 control levels, respectively. These differences in lot medians were not observed when native patient samples were used. Presenting results from different reagent lots in EQA feedback reports can give helpful information to the participants that may explain their deviant EQA results. Information regarding whether the reagent lot differences found in the schemes can affect patient samples is important and should be communicated to the participants as well as to the manufacturers. EQA providers should consider registering and evaluating results from reagent lots. © 2016 American Association for Clinical Chemistry.

7 CFR 987.102 - Lot number.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Lot number. 987.102 Section 987.102 Agriculture... RIVERSIDE COUNTY, CALIFORNIA Administrative Rules Definitions § 987.102 Lot number. Lot number is synonymous with code and means a combination of letters or numbers, or both, acceptable to the Committee, showing...

7 CFR 987.102 - Lot number.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Lot number. 987.102 Section 987.102 Agriculture... RIVERSIDE COUNTY, CALIFORNIA Administrative Rules Definitions § 987.102 Lot number. Lot number is synonymous with code and means a combination of letters or numbers, or both, acceptable to the Committee, showing...

7 CFR 987.102 - Lot number.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Lot number. 987.102 Section 987.102 Agriculture... RIVERSIDE COUNTY, CALIFORNIA Administrative Rules Definitions § 987.102 Lot number. Lot number is synonymous with code and means a combination of letters or numbers, or both, acceptable to the Committee, showing...

7 CFR 987.102 - Lot number.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Lot number. 987.102 Section 987.102 Agriculture... RIVERSIDE COUNTY, CALIFORNIA Administrative Rules Definitions § 987.102 Lot number. Lot number is synonymous with code and means a combination of letters or numbers, or both, acceptable to the Committee, showing...

7 CFR 987.102 - Lot number.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Lot number. 987.102 Section 987.102 Agriculture... RIVERSIDE COUNTY, CALIFORNIA Administrative Rules Definitions § 987.102 Lot number. Lot number is synonymous with code and means a combination of letters or numbers, or both, acceptable to the Committee, showing...

Reducing overlay sampling for APC-based correction per exposure by replacing measured data with computational prediction

NASA Astrophysics Data System (ADS)

Noyes, Ben F.; Mokaberi, Babak; Oh, Jong Hun; Kim, Hyun Sik; Sung, Jun Ha; Kea, Marc

2016-03-01

One of the keys to successful mass production of sub-20nm nodes in the semiconductor industry is the development of an overlay correction strategy that can meet specifications, reduce the number of layers that require dedicated chuck overlay, and minimize measurement time. Three important aspects of this strategy are: correction per exposure (CPE), integrated metrology (IM), and the prioritization of automated correction over manual subrecipes. The first and third aspects are accomplished through an APC system that uses measurements from production lots to generate CPE corrections that are dynamically applied to future lots. The drawback of this method is that production overlay sampling must be extremely high in order to provide the system with enough data to generate CPE. That drawback makes IM particularly difficult because of the throughput impact that can be created on expensive bottleneck photolithography process tools. The goal is to realize the cycle time and feedback benefits of IM coupled with the enhanced overlay correction capability of automated CPE without impacting process tool throughput. This paper will discuss the development of a system that sends measured data with reduced sampling via an optimized layout to the exposure tool's computational modelling platform to predict and create "upsampled" overlay data in a customizable output layout that is compatible with the fab user CPE APC system. The result is dynamic CPE without the burden of extensive measurement time, which leads to increased utilization of IM.

Lower pitch is larger, yet falling pitches shrink.

PubMed

Eitan, Zohar; Schupak, Asi; Gotler, Alex; Marks, Lawrence E

2014-01-01

Experiments using diverse paradigms, including speeded discrimination, indicate that pitch and visually-perceived size interact perceptually, and that higher pitch is congruent with smaller size. While nearly all of these studies used static stimuli, here we examine the interaction of dynamic pitch and dynamic size, using Garner's speeded discrimination paradigm. Experiment 1 examined the interaction of continuous rise/fall in pitch and increase/decrease in object size. Experiment 2 examined the interaction of static pitch and size (steady high/low pitches and large/small visual objects), using an identical procedure. Results indicate that static and dynamic auditory and visual stimuli interact in opposite ways. While for static stimuli (Experiment 2), higher pitch is congruent with smaller size (as suggested by earlier work), for dynamic stimuli (Experiment 1), ascending pitch is congruent with growing size, and descending pitch with shrinking size. In addition, while static stimuli (Experiment 2) exhibit both congruence and Garner effects, dynamic stimuli (Experiment 1) present congruence effects without Garner interference, a pattern that is not consistent with prevalent interpretations of Garner's paradigm. Our interpretation of these results focuses on effects of within-trial changes on processing in dynamic tasks and on the association of changes in apparent size with implied changes in distance. Results suggest that static and dynamic stimuli can differ substantially in their cross-modal mappings, and may rely on different processing mechanisms.

Econometric testing on linear and nonlinear dynamic relation between stock prices and macroeconomy in China

NASA Astrophysics Data System (ADS)

Borjigin, Sumuya; Yang, Yating; Yang, Xiaoguang; Sun, Leilei

2018-03-01

Many researchers have realized that there is a strong correlation between stock prices and macroeconomy. In order to make this relationship clear, a lot of studies have been done. However, the causal relationship between stock prices and macroeconomy has still not been well explained. A key point is that, most of the existing research adopts linear and stable models to investigate the correlation of stock prices and macroeconomy, while the real causality of that may be nonlinear and dynamic. To fill this research gap, we investigate the nonlinear and dynamic causal relationships between stock prices and macroeconomy. Based on the case of China's stock prices and acroeconomy measures from January 1992 to March 2017, we compare the linear Granger causality test models with nonlinear ones. Results demonstrate that the nonlinear dynamic Granger causality is much stronger than linear Granger causality. From the perspective of nonlinear dynamic Granger causality, China's stock prices can be viewed as "national economic barometer". On the one hand, this study will encourage researchers to take nonlinearity and dynamics into account when they investigate the correlation of stock prices and macroeconomy; on the other hand, our research can guide regulators and investors to make better decisions.

Development of an Accelerated Hydrogen Embrittlement Test for Manganese Phosphated Steels

DTIC Science & Technology

2011-05-01

from the same vendor (RSL Testing Systems) and lot (HT/ HTP ) were used. See Appendix B for the certifications for lots HT/ HTP . Note: lot HTP is...Based on the vendor certification of the notched tensile specimens from RSL lot HT/ HTP , the NTS was 373 ksi and the average load at failure was...Systems Lot HT/ HTP ). Note that use of a higher reference NTS and load to failure is a conservative approach since the specimens will experience

7 CFR 932.151 - Incoming regulations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... inspection station other than the one where the lot was sampled. (b) Lot identification. Immediately upon... complete Form COC 3A or 3C, weight and grade report or such other lot identification form as may be... performance of all actions connected with the identification of lots of olives, the weighing of boxes or bins...

7 CFR 27.12 - Classification request for each lot of cotton.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Classification request for each lot of cotton. 27.12... CONTAINER REGULATIONS COTTON CLASSIFICATION UNDER COTTON FUTURES LEGISLATION Regulations Classification Requests § 27.12 Classification request for each lot of cotton. For each lot or mark of cotton of which the...

7 CFR 27.12 - Classification request for each lot of cotton.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Classification request for each lot of cotton. 27.12... CONTAINER REGULATIONS COTTON CLASSIFICATION UNDER COTTON FUTURES LEGISLATION Regulations Classification Requests § 27.12 Classification request for each lot of cotton. For each lot or mark of cotton of which the...

7 CFR 27.12 - Classification request for each lot of cotton.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Classification request for each lot of cotton. 27.12... CONTAINER REGULATIONS COTTON CLASSIFICATION UNDER COTTON FUTURES LEGISLATION Regulations Classification Requests § 27.12 Classification request for each lot of cotton. For each lot or mark of cotton of which the...

7 CFR 27.12 - Classification request for each lot of cotton.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Classification request for each lot of cotton. 27.12... CONTAINER REGULATIONS COTTON CLASSIFICATION UNDER COTTON FUTURES LEGISLATION Regulations Classification Requests § 27.12 Classification request for each lot of cotton. For each lot or mark of cotton of which the...

7 CFR 27.12 - Classification request for each lot of cotton.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Classification request for each lot of cotton. 27.12... CONTAINER REGULATIONS COTTON CLASSIFICATION UNDER COTTON FUTURES LEGISLATION Regulations Classification Requests § 27.12 Classification request for each lot of cotton. For each lot or mark of cotton of which the...

46 CFR 160.077-23 - Production tests and inspections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... fixed anchor, or (C) a tensile test machine that is capable of holding a given tension. The assembly... testing of each incoming lot of inflation chamber material before using that lot in production; (iii) Have... inspector must perform or supervise testing and inspection of at least one PFD lot in each five lots...

Choosing a design to fit the situation: how to improve specificity and positive predictive values using Bayesian lot quality assurance sampling.

PubMed

Olives, Casey; Pagano, Marcello

2013-02-01

Lot Quality Assurance Sampling (LQAS) is a provably useful tool for monitoring health programmes. Although LQAS ensures acceptable Producer and Consumer risks, the literature alleges that the method suffers from poor specificity and positive predictive values (PPVs). We suggest that poor LQAS performance is due, in part, to variation in the true underlying distribution. However, until now the role of the underlying distribution in expected performance has not been adequately examined. We present Bayesian-LQAS (B-LQAS), an approach to incorporating prior information into the choice of the LQAS sample size and decision rule, and explore its properties through a numerical study. Additionally, we analyse vaccination coverage data from UNICEF's State of the World's Children in 1968-1989 and 2008 to exemplify the performance of LQAS and B-LQAS. Results of our numerical study show that the choice of LQAS sample size and decision rule is sensitive to the distribution of prior information, as well as to individual beliefs about the importance of correct classification. Application of the B-LQAS approach to the UNICEF data improves specificity and PPV in both time periods (1968-1989 and 2008) with minimal reductions in sensitivity and negative predictive value. LQAS is shown to be a robust tool that is not necessarily prone to poor specificity and PPV as previously alleged. In situations where prior or historical data are available, B-LQAS can lead to improvements in expected performance.

A Comparative Study on the Lot Release Systems for Vaccines as of 2016.

PubMed

Fujita, Kentaro; Naito, Seishiro; Ochiai, Masaki; Konda, Toshifumi; Kato, Atsushi

2017-09-25

Many countries have already established their own vaccine lot release system that is designed for each country's situation: while the World Health Organization promotes for the convergence of these regulatory systems so that vaccines of assured quality are provided globally. We conducted a questionnaire-based investigation of the lot release systems for vaccines in 7 countries and 2 regions. We found that a review of the summary protocol by the National Regulatory Authorities was commonly applied for the independent lot release of vaccines, however, we also noted some diversity between countries, especially in regard to the testing policy. Some countries and regions, including Japan, regularly tested every lot of vaccines, whereas the frequency of these tests was reduced in other countries and regions as determined based on the risk assessment of these products. Test items selected for the lot release varied among the countries or regions investigated, although there was a tendency to prioritize the potency tests. An understanding of the lot release policy may contribute to improving and harmonizing the lot release system globally in the future.

Greening vacant lots to reduce violent crime: a randomised controlled trial

PubMed Central

Garvin, Eugenia C; Cannuscio, Carolyn C; Branas, Charles C

2014-01-01

Background Vacant lots are often overgrown with unwanted vegetation and filled with trash, making them attractive places to hide illegal guns, conduct illegal activities such as drug sales and prostitution, and engage in violent crime. There is some evidence that greening vacant lots is associated with reductions in violent crime. Methods We performed a randomised controlled trial of vacant lot greening to test the impact of this intervention on police reported crime and residents’ perceptions of safety and disorder. Greening consisted of cleaning the lots, planting grass and trees, and building a wooden fence around the perimeter. We randomly allocated two vacant lot clusters to the greening intervention or to the control status (no intervention). Administrative data were used to determine crime rates, and local resident interviews at baseline (n=29) and at follow-up (n=21) were used to assess perceptions of safety and disorder. Results Unadjusted difference-in-differences estimates showed a non-significant decrease in the number of total crimes and gun assaults around greened vacant lots compared with control. People around the intervention vacant lots reported feeling significantly safer after greening compared with those living around control vacant lots (p<0.01). Conclusions In this study, greening was associated with reductions in certain gun crimes and improvements in residents’ perceptions of safety. A larger randomised controlled trial is needed to further investigate the link between vacant lot greening and violence reduction. PMID:22871378

Tropical stormwater floods: a sustainable solution

NASA Astrophysics Data System (ADS)

Molinie, Jack; Bade, Francois; Nagau, Jimmy; Nuiro, Paul

2017-04-01

Stormwater management is one of the most difficult problem of urban and suburban area. The urban runoff volume related to rain intensity and surfaces properties can lead to flood. Thereby, urban flooding creates considerable infrastructure problem, economics and human damages. In tropical countries, burgeoning human population coupled with unplanned urbanization altered the natural drainage. Consequently, classical intense rain around 100 cm/h produces frequent street flooding. In our case, we study the management of intense tropical rain, by using a network of individual rain storage tanks. The study area is economical and industrial zone installed in a coastal plain , with seventy per cent of impermeable surface (roads, parking lots, building roof, …) and thirty per cent of wetland (mangrove, …). Our solution is to delay the routes and parking lots runoff to the roof one. We propose sustainable individual water storage and a real time dynamical management, which permit to control the roof water arrival in the stormwater culvert. During the remaining time, the stored rainwater can be used for domestic activities instead of the use of drinking water.

21 CFR 610.2 - Requests for samples and protocols; official release.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Biologics Evaluation and Research, a manufacturer shall not distribute a lot of a product until the lot is... Evaluation and Research, a manufacturer shall not distribute a lot of a biological product until the lot is... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Requests for samples and protocols; official...

21 CFR 610.2 - Requests for samples and protocols; official release.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Biologics Evaluation and Research, a manufacturer shall not distribute a lot of a product until the lot is... Evaluation and Research, a manufacturer shall not distribute a lot of a biological product until the lot is... 21 Food and Drugs 7 2011-04-01 2010-04-01 true Requests for samples and protocols; official...

Meteor-Shower on Mars Indicates Cometary Activity Far Away From the Sun

NASA Astrophysics Data System (ADS)

Sekhar, Aswin; ASHER, DAVID

2015-08-01

Introduction: The close encounter of Comet C/2013 A1 (Siding Spring) with Mars on 2014 Oct 19 at 1830h (UT) generated a lot of interest and modelling work [1] [2] [3] in the solar system community. A recent (on 2014 Nov 7) press release from NASA implied that a meteor shower was detected on Mars by their space instruments some hours after the comet-Mars close encounter. Various work [4] [5] [6] has suggested that very specific meteoroid sizes and ejection conditions may be required to produce meteor phenomena at Mars at the given times.Stream dynamics: Meteoroid stream modelling and their orbital geometry calculations have gained high precision over the years. In this work, we compute in detail the structure of the cloud of meteoroids released by C/2013 A1, showing its dependence on heliocentric ejection distances, 3-dimensional ejection velocities, and particle sizes. Our calculations using numerical integrator MERCURY, [7], incorporating radiation pressure, [8], show that ejection of particles at large heliocentric distances (about 7 au to 13 au) from C/2013 A1 could lead to evolution of a dense meteoroid cloud which intersects Mars a few hours after the comet-Mars close encounter. Hence this detection of a meteor shower on Mars by space instruments is an indirect confirmation of cometary activity at large distances which has rarely been observed directly by telescopes so far. Furthermore it shows that comprehensive threat estimation needs to be done for satellites orbiting the Earth when dynamically new comets come very close to the Earth in future.References:[1] Vaubaillon J., Macquet L., Soja R. 2014. MNRAS. 439: 3294.[2] Moorhead A. V., Wiegert P. A., Cooke W. J. 2014. Icarus. 231:13.[3] Ye Q.-Z., Hui M.-T., 2014, ApJ, 787: 115.[4] Farnocchia D. et al. 2014. ApJL. 790: 114.[5] Kelley M. S. P. et al. 2014, ApJL, 792: 16.[6] Tricarico P. et al., 2014, ApJL, 787: 35.[7] Chambers J. E. 1999. MNRAS. 304: 793.[8] Burns J. A, Lamy P. L., Soter S. 1979. Icarus. 40: 1.

Extending cluster Lot Quality Assurance Sampling designs for surveillance programs

PubMed Central

Hund, Lauren; Pagano, Marcello

2014-01-01

Lot quality assurance sampling (LQAS) has a long history of applications in industrial quality control. LQAS is frequently used for rapid surveillance in global health settings, with areas classified as poor or acceptable performance based on the binary classification of an indicator. Historically, LQAS surveys have relied on simple random samples from the population; however, implementing two-stage cluster designs for surveillance sampling is often more cost-effective than simple random sampling. By applying survey sampling results to the binary classification procedure, we develop a simple and flexible non-parametric procedure to incorporate clustering effects into the LQAS sample design to appropriately inflate the sample size, accommodating finite numbers of clusters in the population when relevant. We use this framework to then discuss principled selection of survey design parameters in longitudinal surveillance programs. We apply this framework to design surveys to detect rises in malnutrition prevalence in nutrition surveillance programs in Kenya and South Sudan, accounting for clustering within villages. By combining historical information with data from previous surveys, we design surveys to detect spikes in the childhood malnutrition rate. PMID:24633656

High stability of yellow fever 17D-204 vaccine: a 12-year restrospective analysis of large-scale production.

PubMed

Barban, V; Girerd, Y; Aguirre, M; Gulia, S; Pétiard, F; Riou, P; Barrere, B; Lang, J

2007-04-12

We have retrospectively analyzed 12 bulk lots of yellow fever vaccine Stamaril, produced between 1990 and 2002 and prepared from the same seed lot that has been in continuous use since 1990. All vaccine batches displayed identical genome sequence. Only four nucleotide substitutions were observed, compared to previously published sequence, with no incidence at amino-acid level. Fine analysis of viral plaque size distribution was used as an additional marker for genetic stability and demonstrated a remarkable homogeneity of the viral population. The total virus load, measured by qRT-PCR, was also homogeneous pointing out reproducibility of the vaccine production process. Mice inoculated intracerebrally with the different bulks exhibited a similar average survival time, and ratio between in vitro potency and mouse LD(50) titers remained constant from batch-to-batch. Taken together, these data demonstrate the genetic stability of the strain at mass production level over a period of 12 years and reinforce the generally admitted idea of the safety of YF17D-based vaccines.

Extending cluster lot quality assurance sampling designs for surveillance programs.

PubMed

Hund, Lauren; Pagano, Marcello

2014-07-20

Lot quality assurance sampling (LQAS) has a long history of applications in industrial quality control. LQAS is frequently used for rapid surveillance in global health settings, with areas classified as poor or acceptable performance on the basis of the binary classification of an indicator. Historically, LQAS surveys have relied on simple random samples from the population; however, implementing two-stage cluster designs for surveillance sampling is often more cost-effective than simple random sampling. By applying survey sampling results to the binary classification procedure, we develop a simple and flexible nonparametric procedure to incorporate clustering effects into the LQAS sample design to appropriately inflate the sample size, accommodating finite numbers of clusters in the population when relevant. We use this framework to then discuss principled selection of survey design parameters in longitudinal surveillance programs. We apply this framework to design surveys to detect rises in malnutrition prevalence in nutrition surveillance programs in Kenya and South Sudan, accounting for clustering within villages. By combining historical information with data from previous surveys, we design surveys to detect spikes in the childhood malnutrition rate. Copyright © 2014 John Wiley & Sons, Ltd.

Fueling the AGN

NASA Astrophysics Data System (ADS)

Combes, F.

Active Galactic Nuclei are fueled from material (gas or stars) that are in general far away from the gravitational influence of the central black hole, the engine thought to be responsible for their activity. The required material has a lot of angular momentum that, a priori, is quite difficult to evacuate. The various dynamical mechanisms that may play a role in this game are reviewed, including m = 2 perturbations (bars and spirals), m = 1 perturbations (spirals, warps, lopsidedness), and tidal interactions between galaxies and mergers. In the latest stages of the merger, a binary black hole could be formed, and its influence on the dynamics and fueling is discussed. Starbursts are often associated with AGN, and the nature of their particular connection, and their role in the nuclear fueling is described. Evolution of the fueling efficiency with redshift is addressed.

Dynamic compressive properties of bovine knee layered tissue

NASA Astrophysics Data System (ADS)

Nishida, Masahiro; Hino, Yuki; Todo, Mitsugu

2015-09-01

In Japan, the most common articular disease is knee osteoarthritis. Among many treatment methodologies, tissue engineering and regenerative medicine have recently received a lot of attention. In this field, cells and scaffolds are important, both ex vivo and in vivo. From the viewpoint of effective treatment, in addition to histological features, the compatibility of mechanical properties is also important. In this study, the dynamic and static compressive properties of bovine articular cartilage-cancellous bone layered tissue were measured using a universal testing machine and a split Hopkinson pressure bar method. The compressive behaviors of bovine articular cartilage-cancellous bone layered tissue were examined. The effects of strain rate on the maximum stress and the slope of stress-strain curves of the bovine articular cartilage-cancellous bone layered tissue were discussed.

Proceedings of the DoD Information Analysis Center Conference (3rd) Held at Naval Surface Weapons Center, White Oak, Silver Spring, Maryland, 8-9 December 1981,

DTIC Science & Technology

1982-12-09

34 .: .. . .2 .., - " SESSION II Mr. Jerome Persh, Staff Specialist for Materials and qtructures, OUSDR&E Mr. Charles Miller. Program Director for Federal...Control Division, Office of Assistant Secretary of Defense Management Systems Mr. Jerome Pearson, Air Force Flight Dynamics Laboratory Mr. Harry Pebly...your support and I solicit your assistance. The selection of subjects for the Conference is an excellent one; we are all going to learn a lot here. The

Active colloidal molecules

NASA Astrophysics Data System (ADS)

Löwen, Hartmut

2018-03-01

Like ordinary molecules are composed of atoms, colloidal molecules consist of several species of colloidal particles tightly bound together. If one of these components is self-propelled or swimming, novel “active colloidal molecules” emerge. Active colloidal molecules exist on various levels such as “homonuclear”, “heteronuclear” and “polymeric” and possess a dynamical function moving as propellers, spinners or rotors. Self-assembly of such active complexes has been studied a lot recently and this perspective article summarizes recent progress and gives an outlook to future developments in the rapidly expanding field of active colloidal molecules.

Development of small scale cell culture models for screening poloxamer 188 lot-to-lot variation.

PubMed

Peng, Haofan; Hall, Kaitlyn M; Clayton, Blake; Wiltberger, Kelly; Hu, Weiwei; Hughes, Erik; Kane, John; Ney, Rachel; Ryll, Thomas

2014-01-01

Shear protectants such as poloxamer 188 play a critical role in protecting cells during cell culture bioprocessing. Lot-to-lot variation of poloxamer 188 was experienced during a routine technology transfer across sites of similar scale and equipment. Cell culture medium containing a specific poloxamer 188 lot resulted in an unusual drop in cell growth, viability, and titer during manufacturing runs. After switching poloxamer lots, culture performance returned to the expected level. In order to control the quality of poloxamer 188 and thus maintain better consistency in manufacturing, multiple small scale screening models were developed. Initially, a 5L bioreactor model was established to evaluate cell damage by high sparge rates with different poloxamer 188 lots. Subsequently, a more robust, simple, and efficient baffled shake flask model was developed. The baffled shake flask model can be performed in a high throughput manner to investigate the cell damage in a bubbling environment. The main cause of the poor performance was the loss of protection, rather than toxicity. It was also suggested that suspicious lots can be identified using different cell line and media. The screening methods provide easy, yet remarkable models for understanding and controlling cell damage due to raw material lot variation as well as studying the interaction between poloxamer 188 and cells. © 2014 American Institute of Chemical Engineers.

Mentha spicata L. infusions as sources of antioxidant phenolic compounds: emerging reserve lots with special harvest requirements.

PubMed

Rita, Ingride; Pereira, Carla; Barros, Lillian; Santos-Buelga, Celestino; Ferreira, Isabel C F R

2016-10-12

Mentha spicata L., commonly known as spearmint, is widely used in both fresh and dry forms, for infusion preparation or in European and Indian cuisines. Recently, with the evolution of the tea market, several novel products with added value are emerging, and the standard lots have evolved to reserve lots, with special harvest requirements that confer them with enhanced organoleptic and sensorial characteristics. The apical leaves of these batches are collected in specific conditions having, then, a different chemical profile. In the present study, standard and reserve lots of M. spicata were assessed in terms of the antioxidants present in infusions prepared from the different lots. The reserve lots presented the highest concentration in all the compounds identified in relation to the standard lots, with 326 and 188 μg mL -1 of total phenolic compounds, respectively. Both types of samples presented rosmarinic acid as the most abundant phenolic compound, at concentrations of 169 and 101 μg mL -1 for reserve and standard lots, respectively. The antioxidant activity was higher in the reserve lots which had the highest total phenolic compounds content, with EC 50 values ranging from 152 to 336 μg mL -1 . The obtained results provide scientific information that may allow the consumer to make a conscientious choice.

Detection of bovine viral diarrhoea virus nucleic acid, but not infectious virus, in bovine serum used for human vaccine manufacture.

PubMed

Laassri, Majid; Mee, Edward T; Connaughton, Sarah M; Manukyan, Hasmik; Gruber, Marion; Rodriguez-Hernandez, Carmen; Minor, Philip D; Schepelmann, Silke; Chumakov, Konstantin; Wood, David J

2018-06-22

Bovine viral diarrhoea virus (BVDV) is a cattle pathogen that has previously been reported to be present in bovine raw materials used in the manufacture of biological products for human use. Seven lots of trivalent measles, mumps and rubella (MMR) vaccine and 1 lot of measles vaccine from the same manufacturer, together with 17 lots of foetal bovine serum (FBS) from different vendors, 4 lots of horse serum, 2 lots of bovine trypsin and 5 lots of porcine trypsin were analysed for BVDV using recently developed techniques, including PCR assays for BVDV detection, a qRT-PCR and immunofluorescence-based virus replication assays, and deep sequencing to identify and genotype BVDV genomes. All FBS lots and one lot of bovine-derived trypsin were PCR-positive for the presence of BVDV genome; in contrast all vaccine lots and the other samples were negative. qRT-PCR based virus replication assay and immunofluorescence-based infection assay detected no infectious BVDV in the PCR-positive samples. Complete BVDV genomes were generated from FBS samples by deep sequencing, and all were BVDV type 1. These data confirmed that BVDV nucleic acid may be present in bovine-derived raw materials, but no infectious virus or genomic RNA was detected in the final vaccine products. Copyright © 2018 International Alliance for Biological Standardization. All rights reserved.

7 CFR 983.18 - Lot.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Definitions § 983.18 Lot. Lot means any quantity of pistachios that is submitted for...

75 FR 36673 - Notice of Inventory Completion: Public Museum of West Michigan, Grand Rapids, MI

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-28

... red ochre, 1 shell bracelet, 1 lot of bird bone, 1 flint flake, and 1 projectile point fragment. At an... 33 associated funerary objects are 1 Busycon shell dipper, 16 lots of bone awls and fragments, 1... lots of polished bone, 1 pottery vessel, and 1 lot of turtle carapace fragments. In 1879, human remains...

38 CFR 36.4255 - Loans for the acquisition of a lot.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Loans for the acquisition of a lot. 36.4255 Section 36.4255 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS... of a lot. (a) A loan to finance all or part of the cost of acquisition by the veteran of a lot on...

38 CFR 36.4255 - Loans for the acquisition of a lot.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2013-07-01 2013-07-01 false Loans for the acquisition of a lot. 36.4255 Section 36.4255 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS... of a lot. (a) A loan to finance all or part of the cost of acquisition by the veteran of a lot on...

38 CFR 36.4255 - Loans for the acquisition of a lot.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2012-07-01 2012-07-01 false Loans for the acquisition of a lot. 36.4255 Section 36.4255 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS... of a lot. (a) A loan to finance all or part of the cost of acquisition by the veteran of a lot on...

38 CFR 36.4255 - Loans for the acquisition of a lot.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Loans for the acquisition of a lot. 36.4255 Section 36.4255 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS... of a lot. (a) A loan to finance all or part of the cost of acquisition by the veteran of a lot on...

38 CFR 36.4255 - Loans for the acquisition of a lot.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2014-07-01 2014-07-01 false Loans for the acquisition of a lot. 36.4255 Section 36.4255 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS... of a lot. (a) A loan to finance all or part of the cost of acquisition by the veteran of a lot on...

Non-Maximally Decimated Filter Banks Enable Adaptive Frequency Hopping for Unmanned Aircraft Vehicles

NASA Technical Reports Server (NTRS)

Venosa, Elettra; Vermeire, Bert; Alakija, Cameron; Harris, Fred; Strobel, David; Sheehe, Charles J.; Krunz, Marwan

2017-01-01

In the last few years, radio technologies for unmanned aircraft vehicle (UAV) have advanced very rapidly. The increasing need to fly unmanned aircraft systems (UAS) in the national airspace system (NAS) to perform missions of vital importance to national security, defense, and science has pushed ahead the design and implementation of new radio platforms. However, a lot still has to be done to improve those radios in terms of performance and capabilities. In addition, an important aspect to account for is hardware cost and the feasibility to implement these radios using commercial off-the-shelf (COTS) components. UAV radios come with numerous technical challenges and their development involves contributions at different levels of the design. Cognitive algorithms need to be developed in order to perform agile communications using appropriate frequency allocation while maintaining safe and efficient operations in the NAS and, digital reconfigurable architectures have to be designed in order to ensure a prompt response to environmental changes. Command and control (C2) communications have to be preserved during "standard" operations while crew operations have to be minimized. It is clear that UAV radios have to be software-defined systems, where size, weight and power consumption (SWaP) are critical parameters. This paper provides preliminary results of the efforts performed to design a fully digital radio architecture as part of a NASA Phase I STTR. In this paper, we will explain the basic idea and technical principles behind our dynamic/adaptive frequency hopping radio for UAVs. We will present our Simulink model of the dynamic FH radio transmitter design for UAV communications and show simulation results and FPGA system analysis.

Slow sedimentary processes on-a-chip: experiments on porous flow effects on granular bed creep

NASA Astrophysics Data System (ADS)

Houssais, M.; Maldarelli, C.; Shattuck, M.; Morris, J. F.

2017-12-01

Steep soils dynamics is hard to catch. they exhibit very slow granular creep most of the time, and sometimes, mostly under or after rain, turn into a landslide, a very fast avalanche flow.The conditions of transition from soil creep to avalanching remains a lot non-understood, and Safe Factor law (empirical criteria, function of rain intensity and duration). On another side, in marine fast deposition environments, compaction drives vertical porous flow, which makes bed shear resistance change, and form over time bed size patterns (pipes, dishes) or mechanical heterogeneities.Capturing how the slow creep dynamics depends on the porous flow would allow for much more accurate landscape evolution modeling.We present here preliminary results of an experimental investigation of one the major triggering condition for soils destabilization: rain infiltration, and more generally porous flow through a tilted granular bed. In a quasi-2D microfluidics channel, a flat sediment bed made of spherical particles is prepared, in fully submerged condition. It is thereafter tilted (at slope under critical slope of avalanching) and simultaneously put under vertical weak porous flow (well under the critical flow of liquefaction regarding positive pressure gradients). The two control parameters are varied, and local particles concentration and motion are measured. Interestingly, although staying in the sub-critical creeping regime, we observe an acceleration of the bed deformation downward, as the porous flow and the bed slope are increased, until the criteria for avalanching is reached. Those results appear to present similitudes with the case of tilted dry sediment bed under controlled vibrations. Consequently it opens the discussion about a potential universal model of landslides triggering due to frequent seismological and rainstorm events.

Effects of residential wastewater treatment systems on ground-water quality in west-central Jefferson County, Colorado

USGS Publications Warehouse

Hall, Dennis C.; Hillier, D.E.; Nickum, Edward; Dorrance, W.G.

1981-01-01

The use of residential wastewater-treatment systems in Evergreen Meadows, Marshdale, and Herzman Mesa, Colo., has degraded ground-water quality to some extent in each community. Age of community; average lot size; slope of land surface; composition, permeability, and thickness of surficial material; density, size , and orientation of fractures; maintenance of wastewater-treatment systems; and presence of animals are factors possibly contributing to the degradation of ground-water quality. When compared with effluent from aeration-treatment tanks, effluent fom septic-treatment tanks is characterized by greater biochemical oxygen demand and greater concentrations of detergents. When compared with effluent from septic-treatment tanks, effluent from aeration-treatment tanks is characterized by greater concentrations of dissolved oxygen, nitrite, nitrate, sulfate, and dissolved solids. (USGS)

Path Searching Based Crease Detection for Large Scale Scanned Document Images

NASA Astrophysics Data System (ADS)

Zhang, Jifu; Li, Yi; Li, Shutao; Sun, Bin; Sun, Jun

2017-12-01

Since the large size documents are usually folded for preservation, creases will occur in the scanned images. In this paper, a crease detection method is proposed to locate the crease pixels for further processing. According to the imaging process of contactless scanners, the shading on both sides of the crease usually varies a lot. Based on this observation, a convex hull based algorithm is adopted to extract the shading information of the scanned image. Then, the possible crease path can be achieved by applying the vertical filter and morphological operations on the shading image. Finally, the accurate crease is detected via Dijkstra path searching. Experimental results on the dataset of real scanned newspapers demonstrate that the proposed method can obtain accurate locations of the creases in the large size document images.

Line trace micro-opto-electro-device

NASA Astrophysics Data System (ADS)

Yi, Deer; Lu, Si; Yan, Yingbai; Pang, Lin; Jin, Guofan

2001-05-01

Since micro robot has merits on small size and flexible movements, it could be used under many situations. A lot of novel designs of micro-robot have been developed recently. However, as miniaturizing the size of the micro-robot, the number of its sensor gets restricted. Then the information from the detectors becomes lack. This makes the micro robot difficult to acquire its status. A micro robot tracing a line has been designed in our lab. With the help of optoelectronic detection and logical algorithm, the micro robot could follow a black line printed on the white ground exactly. The micro robot's intelligence is realized through the program in its microprocessor. The technical details of the micro robot are as follows: dimensions: 30mm*25mm*35**; velocity: 60mm/s.

Study on Insulation Diagnosis of Power Lines in Apartment Houses

NASA Astrophysics Data System (ADS)

Okamoto, Tatsuki; Taki, Shoji; Fukui, Toshiaki; Soga, Akiya; Ezure, Shoichiro; Asano, Jun-Ichi; Uto, Yukio

Insulation diagnosis is vital issue for safety of urban lives despite of the difficulty of power interruption even for the diagnosis. Recently, live-line insulation diagnosis becomes more important and realistic to maintain good insulation conditions of power lines in apartment houses in wide range of residential sizes. This paper describes new trend of insulation diagnosis of power lines of apartment houses based on clip-on current measurement method with a lot of live-line measurement data and also describes the applicability of new live-line insulation diagnostic method.

7 CFR 201.30b - Lot number or other lot identification of vegetable seed in containers of more than 1 pound.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 3 2012-01-01 2012-01-01 false Lot number or other lot identification of vegetable seed in containers of more than 1 pound. 201.30b Section 201.30b Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED)...

7 CFR 201.30b - Lot number or other lot identification of vegetable seed in containers of more than 1 pound.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Lot number or other lot identification of vegetable seed in containers of more than 1 pound. 201.30b Section 201.30b Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED)...

7 CFR 201.30b - Lot number or other lot identification of vegetable seed in containers of more than 1 pound.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 3 2013-01-01 2013-01-01 false Lot number or other lot identification of vegetable seed in containers of more than 1 pound. 201.30b Section 201.30b Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED)...

7 CFR 201.30b - Lot number or other lot identification of vegetable seed in containers of more than 1 pound.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Lot number or other lot identification of vegetable seed in containers of more than 1 pound. 201.30b Section 201.30b Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED)...

7 CFR 201.30b - Lot number or other lot identification of vegetable seed in containers of more than 1 pound.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 3 2014-01-01 2014-01-01 false Lot number or other lot identification of vegetable seed in containers of more than 1 pound. 201.30b Section 201.30b Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED)...

Effects of greening and community reuse of vacant lots on crime

Treesearch

M. Kondo; B. Hohl; S. Han; C. Branas

2016-01-01

The Youngstown Neighborhood Development Corporation initiated a ‘Lots of Green’ programme to reuse vacant land in 2010. We performed a difference-in-differences analysis of the effects of this programme on crime in and around newly treated lots, in comparison to crimes in and around randomly selected and matched, untreated vacant lot controls. The effects of two types...

76 FR 30745 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-26

... Change Amending Its Rules To Remove the Concept of an ``Odd Lot Dealer'' May 19, 2011. Pursuant to... remove the concept of an ``Odd Lot Dealer.'' The text of the proposed rule change is available at the... proposes to amend its rules to remove the concept of an Odd Lot Dealer. An Odd Lot Dealer is any Market...

Effect of Soybean Casein Digest Agar Lot on Number of Bacillus stearothermophilus Spores Recovered †

PubMed Central

Pflug, I. J.; Smith, Geraldine M.; Christensen, Ronald

1981-01-01

In recent years it has become increasingly apparent that Bacillus stearothermophilus spores are affected by various environmental factors that influence the performance of the spores as biological indicators. One environmental factor is the recovery medium. The effect of different lots of commercial soybean casein digest agar on the number of colony-forming units per plate was examined in two series of experiments: (i) several lots of medium from two manufacturers were compared in single experiments, and (ii) paired media experiments with four lots of medium were carried out and yielded three-point survivor curves. The results demonstrate that commercial soybean casein digest agar is variable on a lot-to-lot basis. The variation was lowest when recovering unheated or minimally heated spores and increased greatly with the severity of heating. PMID:16345822

Parking lot sealcoat: An unrecognized source of urban polycyclic aromatic hydrocarbons

USGS Publications Warehouse

Mahler, B.J.; Van Metre, P.C.; Bashara, T.J.; Wilson, J.T.; Johns, D.A.

2005-01-01

Polycyclic aromatic hydrocarbons (PAHs) are a ubiquitous contaminant in urban environments. Although numerous sources of PAHs to urban runoff have been identified, their relative importance remains uncertain. We show that a previously unidentified source of urban PAHs, parking lot sealcoat, may dominate loading of PAHs to urban water bodies in the United States. Particles in runoff from parking lots with coal-tar emulsion sealcoat had mean concentrations of PAHs of 3500 mg/kg, 65 times higher than the mean concentration from unsealed asphalt and cement lots. Diagnostic ratios of individual PAHs indicating sources are similar for particles from coal-tar emulsion sealed lots and suspended sediment from four urban streams. Contaminant yields projected to the watershed scale for the four associated watersheds indicate that runoff from sealed parking lots could account for the majority of stream PAH loads.

Tracking the Spatiotemporal Neural Dynamics of Real-world Object Size and Animacy in the Human Brain.

PubMed

Khaligh-Razavi, Seyed-Mahdi; Cichy, Radoslaw Martin; Pantazis, Dimitrios; Oliva, Aude

2018-06-07

Animacy and real-world size are properties that describe any object and thus bring basic order into our perception of the visual world. Here, we investigated how the human brain processes real-world size and animacy. For this, we applied representational similarity to fMRI and MEG data to yield a view of brain activity with high spatial and temporal resolutions, respectively. Analysis of fMRI data revealed that a distributed and partly overlapping set of cortical regions extending from occipital to ventral and medial temporal cortex represented animacy and real-world size. Within this set, parahippocampal cortex stood out as the region representing animacy and size stronger than most other regions. Further analysis of the detailed representational format revealed differences among regions involved in processing animacy. Analysis of MEG data revealed overlapping temporal dynamics of animacy and real-world size processing starting at around 150 msec and provided the first neuromagnetic signature of real-world object size processing. Finally, to investigate the neural dynamics of size and animacy processing simultaneously in space and time, we combined MEG and fMRI with a novel extension of MEG-fMRI fusion by representational similarity. This analysis revealed partly overlapping and distributed spatiotemporal dynamics, with parahippocampal cortex singled out as a region that represented size and animacy persistently when other regions did not. Furthermore, the analysis highlighted the role of early visual cortex in representing real-world size. A control analysis revealed that the neural dynamics of processing animacy and size were distinct from the neural dynamics of processing low-level visual features. Together, our results provide a detailed spatiotemporal view of animacy and size processing in the human brain.

Micropipette as Coulter counter for submicron particles

NASA Astrophysics Data System (ADS)

Rudzevich, Yauheni; Ordonez, Tony; Evans, Grant; Chow, Lee

2011-03-01

Coulter counter based on micropipette has been around for several decades. Typical commercial Coulter counter has a pore size of 20 μ m, and is designed to detect micron-size blood cells. In recent years, there are a lot of interests in using nanometer pore size Coulter counter to detect single molecule and to sequence DNA. Here we describe a simple nanoparticle counter based on pulled micropipettes with a diameter of 50 -- 500 nm. Borosilicate micropipettes with an initial outer diameter of 1.00 mm and inner diameter of 0.5 mm are used. After pulling, the micropipettes are fire polished and ultrasound cleaned. Chlorinated Ag/AgCl electrodes and 0.1 M of KCl solution are used. The ionic currents are measured using an Axopatch 200B amplifier in the voltage-clamp mode. Several types and sizes of nanoparticles are measured, including plain silica and polystyrene nanospheres. The results will be discussed in terms of pH values of the solution and concentrations of the nanoparticles. Financial support from National Science Foundation (NSF-0901361) is acknowledged.

Frequency Response Studies using Receptance Coupling Approach in High Speed Spindles

NASA Astrophysics Data System (ADS)

Shaik, Jakeer Hussain; Ramakotaiah, K.; Srinivas, J.

2018-01-01

In order to assess the stability of high speed machining, estimate the frequency response at the end of tool tip is of great importance. Evaluating dynamic response of several combinations of integrated spindle-tool holder-tool will consume a lot of time. This paper presents coupled field dynamic response at tool tip for the entire integrated spindle tool unit. The spindle unit is assumed to be relying over the front and rear bearings and investigated using the Timoshenko beam theory to arrive the receptances at different locations of the spindle-tool unit. The responses are further validated with conventional finite element model as well as with the experiments. This approach permits quick outputs without losing accuracy of solution and further these methods are utilized to analyze the various design variables on system dynamics. The results obtained through this analysis are needed to design the better spindle unit in an attempt to reduce the frequency amplitudes at the tool tip to improvise the milling stability during cutting process.

Comparative analysis of age dynamics of average values of body dimensions in children from birth to 7 years.

PubMed

Deryabin, Vasily E; Krans, Valentina M; Fedotova, Tatiana K

2005-07-01

Mean values of different body dimensions in different age cohorts of children make it possible to learn a lot about their dynamic changes. Their comparative analysis, as is usually practiced, in fact leads to a simple description of changes in measurement units (mm or cm) at the average level of some body dimension during a shorter or longer period of time. To estimate comparative intensity of the growth process of different body dimensions, the authors use the analogue of Mahalanobis distance, the so-called Kullback divergence (1967), which does not demand stability of dispersion or correlation coefficients of dimensions in compared cohorts of children. Most of the dimensions, excluding skinfolds, demonstrate growth dynamics with gradually reducing increments from birth to 7 years. Body length has the highest integrative increment, leg length about 94% of body length, body mass 77%, and trunk and extremities circumferences 56%. Skinfolds have a non-monotonic pattern of accumulated standardized increments with some increase until 1-2 years of age.

Design and Analysis of a Dynamic Mobility Management Scheme for Wireless Mesh Network

PubMed Central

Roy, Sudipta

2013-01-01

Seamless mobility management of the mesh clients (MCs) in wireless mesh network (WMN) has drawn a lot of attention from the research community. A number of mobility management schemes such as mesh network with mobility management (MEMO), mesh mobility management (M3), and wireless mesh mobility management (WMM) have been proposed. The common problem with these schemes is that they impose uniform criteria on all the MCs for sending route update message irrespective of their distinct characteristics. This paper proposes a session-to-mobility ratio (SMR) based dynamic mobility management scheme for handling both internet and intranet traffic. To reduce the total communication cost, this scheme considers each MC's session and mobility characteristics by dynamically determining optimal threshold SMR value for each MC. A numerical analysis of the proposed scheme has been carried out. Comparison with other schemes shows that the proposed scheme outperforms MEMO, M3, and WMM with respect to total cost. PMID:24311982

Emergent behaviors of the Schrödinger-Lohe model on cooperative-competitive networks

NASA Astrophysics Data System (ADS)

Huh, Hyungjin; Ha, Seung-Yeal; Kim, Dohyun

2017-12-01

We present several sufficient frameworks leading to the emergent behaviors of the coupled Schrödinger-Lohe (S-L) model under the same one-body external potential on cooperative-competitive networks. The S-L model was first introduced as a possible phenomenological model exhibiting quantum synchronization and its emergent dynamics on all-to-all cooperative networks has been treated via two distinct approaches, Lyapunov functional approach and the finite-dimensional reduction based on pairwise correlations. In this paper, we further generalize the finite-dimensional dynamical systems approach for pairwise correlation functions on cooperative-competitive networks and provide several sufficient frameworks leading to the collective exponential synchronization. For small systems consisting of three and four quantum subsystem, we also show that the system for pairwise correlations can be reduced to the Lotka-Volterra model with cooperative and competitive interactions, in which lots of interesting dynamical patterns appear, e.g., existence of closed orbits and limit-cycles.

Space Age Swimsuit Reduces Drag, Breaks Records

NASA Technical Reports Server (NTRS)

2008-01-01

A space shuttle and a competitive swimmer have a lot more in common than people might realize: Among other forces, both have to contend with the slowing influence of drag. NASA s Aeronautics Research Mission Directorate focuses primarily on improving flight efficiency and generally on fluid dynamics, especially the forces of pressure and viscous drag, which are the same for bodies moving through air as for bodies moving through water. Viscous drag is the force of friction that slows down a moving object through a substance, like air or water. NASA uses wind tunnels for fluid dynamics research, studying the forces of friction in gasses and liquids. Pressure forces, according to Langley Research Center s Stephen Wilkinson, dictate the optimal shape and performance of an airplane or other aero/hydro-dynamic body. In both high-speed flight and swimming, says Wilkinson, a thin boundary layer of reduced velocity fluid surrounds the moving body; this layer is about 2 centimeters thick for a swimmer.

24 CFR 1715.20 - Unlawful sales practices-regulatory provisions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... septic tank operation or there is reasonable assurance that the lot can be served by a central sewage system; (3) The lot is legally accessible; and (4) The lot is free from periodic flooding. ...

24 CFR 1715.20 - Unlawful sales practices-regulatory provisions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... septic tank operation or there is reasonable assurance that the lot can be served by a central sewage system; (3) The lot is legally accessible; and (4) The lot is free from periodic flooding. ...

24 CFR 1715.20 - Unlawful sales practices-regulatory provisions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... septic tank operation or there is reasonable assurance that the lot can be served by a central sewage system; (3) The lot is legally accessible; and (4) The lot is free from periodic flooding. ...

24 CFR 1715.20 - Unlawful sales practices-regulatory provisions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... septic tank operation or there is reasonable assurance that the lot can be served by a central sewage system; (3) The lot is legally accessible; and (4) The lot is free from periodic flooding. ...

Investigation clogging dynamic of permeable pavement systems using embedded sensors

NASA Astrophysics Data System (ADS)

Razzaghmanesh, Mostafa; Borst, Michael

2018-02-01

Permeable pavement is a stormwater control measure commonly selected in both new and retrofit applications. However, there is limited information about the clogging mechanism of these systems that effects the infiltration. A permeable pavement site located at the Seitz Elementary School, on Fort Riley, Kansas was selected for this study. An 80-space parking lot was built behind the school as part of an EPA collaboration with the U.S. Army. The parking lot design includes a permeable interlocking concrete pavement section along the downgradient edge. This study monitored the clogging progress of the pavement section using twelve water content reflectometers and three buried tipping bucket rain gauges. This clogging dynamic investigation was divided into three stages namely pre-clogged, transitional, and clogged. Recorded initial relative water content of all three stages were significantly and negatively correlated to antecedent dry weather periods with stronger correlations during clogged conditions. The peak relative water content correlation with peak rainfall 10-min intensity was significant for the water content reflectometers located on the western edge away from the eastern edge; this correlation was strongest during transition stage. Once clogged, rainfall measurements no longer correlated with the buried tipping bucket rain gauges. Both water content reflectometers and buried tipping bucket rain gauges showed the progress of surface clogging. For every 6 mm of rain, clogging advanced 1 mm across the surface. The results generally support the hypothesis that the clogging progresses from the upgradient to the downgradient edge. The magnitude of the contributing drainage area and rainfall characteristics are effective factors on rate and progression of clogging.

Dynamic code block size for JPEG 2000

NASA Astrophysics Data System (ADS)

Tsai, Ping-Sing; LeCornec, Yann

2008-02-01

Since the standardization of the JPEG 2000, it has found its way into many different applications such as DICOM (digital imaging and communication in medicine), satellite photography, military surveillance, digital cinema initiative, professional video cameras, and so on. The unified framework of the JPEG 2000 architecture makes practical high quality real-time compression possible even in video mode, i.e. motion JPEG 2000. In this paper, we present a study of the compression impact using dynamic code block size instead of fixed code block size as specified in the JPEG 2000 standard. The simulation results show that there is no significant impact on compression if dynamic code block sizes are used. In this study, we also unveil the advantages of using dynamic code block sizes.

Evolutionary dynamics with fluctuating population sizes and strong mutualism.

PubMed

Chotibut, Thiparat; Nelson, David R

2015-08-01

Game theory ideas provide a useful framework for studying evolutionary dynamics in a well-mixed environment. This approach, however, typically enforces a strictly fixed overall population size, deemphasizing natural growth processes. We study a competitive Lotka-Volterra model, with number fluctuations, that accounts for natural population growth and encompasses interaction scenarios typical of evolutionary games. We show that, in an appropriate limit, the model describes standard evolutionary games with both genetic drift and overall population size fluctuations. However, there are also regimes where a varying population size can strongly influence the evolutionary dynamics. We focus on the strong mutualism scenario and demonstrate that standard evolutionary game theory fails to describe our simulation results. We then analytically and numerically determine fixation probabilities as well as mean fixation times using matched asymptotic expansions, taking into account the population size degree of freedom. These results elucidate the interplay between population dynamics and evolutionary dynamics in well-mixed systems.

Evolutionary dynamics with fluctuating population sizes and strong mutualism

NASA Astrophysics Data System (ADS)

Chotibut, Thiparat; Nelson, David R.

2015-08-01

Game theory ideas provide a useful framework for studying evolutionary dynamics in a well-mixed environment. This approach, however, typically enforces a strictly fixed overall population size, deemphasizing natural growth processes. We study a competitive Lotka-Volterra model, with number fluctuations, that accounts for natural population growth and encompasses interaction scenarios typical of evolutionary games. We show that, in an appropriate limit, the model describes standard evolutionary games with both genetic drift and overall population size fluctuations. However, there are also regimes where a varying population size can strongly influence the evolutionary dynamics. We focus on the strong mutualism scenario and demonstrate that standard evolutionary game theory fails to describe our simulation results. We then analytically and numerically determine fixation probabilities as well as mean fixation times using matched asymptotic expansions, taking into account the population size degree of freedom. These results elucidate the interplay between population dynamics and evolutionary dynamics in well-mixed systems.

Effects of constant immigration on the dynamics and persistence of stable and unstable Drosophila populations

PubMed Central

Dey, Snigdhadip; Joshi, Amitabh

2013-01-01

Constant immigration can stabilize population size fluctuations but its effects on extinction remain unexplored. We show that constant immigration significantly reduced extinction in fruitfly populations with relatively stable or unstable dynamics. In unstable populations with oscillations of amplitude around 1.5 times the mean population size, persistence and constancy were unrelated. Low immigration enhanced persistence without affecting constancy whereas high immigration increased constancy without enhancing persistence. In relatively stable populations with erratic fluctuations of amplitude close to the mean population size, both low and high immigration enhanced persistence. In these populations, the amplitude of fluctuations relative to mean population size went down due to immigration, and their dynamics were altered to low-period cycles. The effects of immigration on the population size distribution and intrinsic dynamics of stable versus unstable populations differed considerably, suggesting that the mechanisms by which immigration reduced extinction risk depended on underlying dynamics in complex ways. PMID:23470546

Relating rheology to geometry in large-scale natural shear zones

NASA Astrophysics Data System (ADS)

Platt, John

2016-04-01

The geometry and width of the ductile roots of plate boundary scale faults are very poorly understood. Some field and geophysical data suggests widths of tens of km in the lower crust, possibly more in the upper mantle. Other observations suggest they are much narrower. Dip slip shear zones may flatten out and merge into zones of subhorizontal lower crustal or asthenospheric flow. The width of a ductile shear zone is simply related to relative velocity and strain rate. Strain rate is related to stress through the constitutive relationship. Can we constrain the stress, and do we understand the rheology of materials in ductile shear zones? A lot depends on how shear zones are initiated. If they are localized by pre-existing structures, width and/or rheology may be inherited, and we have too many variables. If shear zones are localized primarily by shear heating, initial shear stress has to be very high (> 1 GPa) to overcome conductive heat loss, and very large feedbacks (both positive and negative) make the system highly unstable. Microstructural weakening requires a minimum level of stress to cause deformation and damage in surrounding rock, thereby buffering the stress. Microstructural weakening leads to grain-size sensitive creep, for which we have constitutive laws, but these are complicated by phase mixing in polyphase materials, by viscous anisotropy, by hydration, and by changes in mineral assemblage. Here are some questions that need to be addressed. (1) If grain-size reduction by dynamic recrystallization results in a switch to grain-size sensitive creep (GSSC) in a stress-buffered shear zone, does dynamic recrystallization stop? Does grain growth set in? If grain-size is still controlled by dislocation processes, then the effective stress exponent for GSSC is 4-5, even though the dominant mechanism may be diffusion and/or grain-boundary sliding (GBS). (2) Is phase mixing in ultramylonites primarily a result of GBS + neighbour switching, creep cavitation and diffusion, or metamorphic reactions? (3) In two-phase / polyphase mixtures, does the strong phase generally form a load-bearing framework, favoring constant strain-rate (Voigt) bound behavior, or does the weak phase form through-going strain pathways, favoring constant stress (Reuss) bound behavior, or do the phases remain well mixed, favoring an intermediate behavior (e.g., Tullis et al model)? (4) How do we deal with the rheological effect of water? Is it simply an unconstrained variable in nature? Is the water fugacity model in flow laws adequate? (5) How can we better relate experimental results (often carried out at constant strain-rate, and not reaching microstructural steady state) to deformation in natural shear zones? Rheological observations on well-constrained natural shear zones are helping us answer some of these questions.

7 CFR 33.7 - Less than carload lot.

Code of Federal Regulations, 2010 CFR

2010-01-01

... ISSUED UNDER AUTHORITY OF THE EXPORT APPLE ACT Definitions § 33.7 Less than carload lot. Less than carload lot means a quantity of apples in packages not exceeding 20,000 pounds gross weight or 400...

7 CFR 33.7 - Less than carload lot.

Code of Federal Regulations, 2014 CFR

2014-01-01

... ISSUED UNDER AUTHORITY OF THE EXPORT APPLE ACT Definitions § 33.7 Less than carload lot. Less than carload lot means a quantity of apples in packages not exceeding 20,000 pounds gross weight or 400...

7 CFR 33.7 - Less than carload lot.

Code of Federal Regulations, 2012 CFR

2012-01-01

... ISSUED UNDER AUTHORITY OF THE EXPORT APPLE ACT Definitions § 33.7 Less than carload lot. Less than carload lot means a quantity of apples in packages not exceeding 20,000 pounds gross weight or 400...

7 CFR 33.7 - Less than carload lot.

Code of Federal Regulations, 2011 CFR

2011-01-01

... ISSUED UNDER AUTHORITY OF THE EXPORT APPLE ACT Definitions § 33.7 Less than carload lot. Less than carload lot means a quantity of apples in packages not exceeding 20,000 pounds gross weight or 400...

7 CFR 33.7 - Less than carload lot.

Code of Federal Regulations, 2013 CFR

2013-01-01

... ISSUED UNDER AUTHORITY OF THE EXPORT APPLE ACT Definitions § 33.7 Less than carload lot. Less than carload lot means a quantity of apples in packages not exceeding 20,000 pounds gross weight or 400...

Parking lot sealcoat: an unrecognized source of urban polycyclic aromatic hydrocarbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbara J. Mahler; Peter C. Van Metre; Thomas J. Bashara

2005-08-01

Polycyclic aromatic hydrocarbons (PAHs) are a ubiquitous contaminant in urban environments. Although numerous sources of PAHs to urban runoff have been identified, their relative importance remains uncertain. The authors show that a previously unidentified source of urban PAHs, parking lot sealcoat, may dominate loading of PAHs to urban water bodies in the United States. Particles in runoff from parking lots with coal-tar emulsion sealcoat had mean concentrations of PAHs of 3500 mg/kg, 65 times higher than the mean concentration from unsealed asphalt and cement lots. Diagnostic ratios of individual PAHs indicating sources are similar for particles from coal-tar emulsion sealedmore » lots and suspended sediment from four urban streams. Contaminant yields projected to the watershed scale for the four associated watersheds indicate that runoff from sealed parking lots could account for the majority of stream PAH loads. 35 refs., 6 figs., 2 tabs.« less

Choosing a design to fit the situation: how to improve specificity and positive predictive values using Bayesian lot quality assurance sampling

PubMed Central

Olives, Casey; Pagano, Marcello

2013-01-01

Background Lot Quality Assurance Sampling (LQAS) is a provably useful tool for monitoring health programmes. Although LQAS ensures acceptable Producer and Consumer risks, the literature alleges that the method suffers from poor specificity and positive predictive values (PPVs). We suggest that poor LQAS performance is due, in part, to variation in the true underlying distribution. However, until now the role of the underlying distribution in expected performance has not been adequately examined. Methods We present Bayesian-LQAS (B-LQAS), an approach to incorporating prior information into the choice of the LQAS sample size and decision rule, and explore its properties through a numerical study. Additionally, we analyse vaccination coverage data from UNICEF’s State of the World’s Children in 1968–1989 and 2008 to exemplify the performance of LQAS and B-LQAS. Results Results of our numerical study show that the choice of LQAS sample size and decision rule is sensitive to the distribution of prior information, as well as to individual beliefs about the importance of correct classification. Application of the B-LQAS approach to the UNICEF data improves specificity and PPV in both time periods (1968–1989 and 2008) with minimal reductions in sensitivity and negative predictive value. Conclusions LQAS is shown to be a robust tool that is not necessarily prone to poor specificity and PPV as previously alleged. In situations where prior or historical data are available, B-LQAS can lead to improvements in expected performance. PMID:23378151

Salix alba and Populus nigra seedlings resistance to physical hydro-sedimentary stresses: nursery experimental approach compared to in situ measurements

NASA Astrophysics Data System (ADS)

Wintenberger, Coraline; Rodrigues, Stephane; Breheret, Jean-Gabriel; Jugé, Philippe; Villar, Marc

2014-05-01

In Europe, riparian Salicaceae is declining following the loss of potential germination areas associated with river management. Nevertheless, as an exception for lowland rivers, the Loire River (France) shows in its middle reaches an efficient sexual regeneration of Populus nigra and Salix alba species on bare sediments deposited during flood events. The study focuses on the influence of flow, sediment dynamics and fluvial maintenance operations on the establishment and survival of black poplar and white willow seedlings during the first year of development in a lowland sandy-gravel river, the Middle Loire. Main questions are: what is the influence of morphological and sedimentary features on seedlings recruitment and how do they withstand the hydro-sedimentary stresses occurring during high flow periods? How fluvial management works, and induced morphology and sedimentary features, modify the sediment dynamics and subsequent establishment and maintenance of seedlings? To answer these questions, we developed an ex-situ approach which allowed, under controlled conditions, to determine the influence of the sedimentological characteristics of the substrate on the development and maintenance of seedlings with a specific focus on the root system. Three experiments were carried out for three sedimentary mixtures from the river (sand, sand-gravel and 0.2 m of sand superimposed on sand-gravel mixture) that correspond to grain size and stratigraphy conditions often observed on bars and secondary channels in the Loire. The experimental design includes 108 plots of 1 m3, with 400 seeds per plot (corresponding to the Loire density measurements) and combining seeds from two species, three sedimentary mixtures, four replicates and three experiments. Experiment 1 (control) is based on the architecture of root systems using the WinRHIZO image analysis software. Experiment 2 is relative to the evaluation of constraints leading to "uprooting" of seedlings. Experiment 3 provides data on the seedlings survival once buried during a flood event. Genetic diversity of the seed lots will be investigated via biomass and shoot / root ratio. Results reveal that willow seedlings have a higher density of roots compared to poplar. In sand mixture, poplar has a taproot system; in sand-gravel mixture, taproot is divided into several roots which leads to a branched root system. The required forces to uprooting are twice much important for sand-gravel mixture. In situ measurements detail the sediment dynamics and morphological evolution during and after floods (topography, scour/fill processes, grain size surveys, flow velocity, sediment transport rates) on a managed alluvial bar. Results associated with floods occurring after fluvial management works highlight the rapid regeneration of bedforms associated with sedimentary and hydraulics constraints. This leads to the development of new morphological and sedimentological units, suitable for seedlings recruitment. Thirty plots measurements of seedlings (densities and species) established were associated with these news physical conditions over the bar. Black poplar and white willow appeared for a wide range of grain sizes and on specific morphological units. Seedlings survival will be analyzed with regard to physical constraints determined for each plot from measurements of hydro-sedimentary dynamics and then compared to ex situ results.

Relaxation dynamics in a binary hard-ellipse liquid.

PubMed

Xu, Wen-Sheng; Sun, Zhao-Yan; An, Li-Jia

2015-01-21

Structural relaxation in binary hard spherical particles has been shown recently to exhibit a wealth of remarkable features when size disparity or mixture composition is varied. In this paper, we test whether or not similar dynamical phenomena occur in glassy systems composed of binary hard ellipses. We demonstrate via event-driven molecular dynamics simulation that a binary hard-ellipse mixture with an aspect ratio of two and moderate size disparity displays characteristic glassy dynamics upon increasing density in both the translational and the rotational degrees of freedom. The rotational glass transition density is found to be close to the translational one for the binary mixtures investigated. More importantly, we assess the influence of size disparity and mixture composition on the relaxation dynamics. We find that an increase of size disparity leads, both translationally and rotationally, to a speed up of the long-time dynamics in the supercooled regime so that both the translational and the rotational glass transition shift to higher densities. By increasing the number concentration of the small particles, the time evolution of both translational and rotational relaxation dynamics at high densities displays two qualitatively different scenarios, i.e., both the initial and the final part of the structural relaxation slow down for small size disparity, while the short-time dynamics still slows down but the final decay speeds up in the binary mixture with large size disparity. These findings are reminiscent of those observed in binary hard spherical particles. Therefore, our results suggest a universal mechanism for the influence of size disparity and mixture composition on the structural relaxation in both isotropic and anisotropic particle systems.

A power system design and analysis of carbon nano-tubes field emission displays

NASA Astrophysics Data System (ADS)

Wang, Jong C.; Yao, W. C.

2006-01-01

In new generation Flat Panel Displays(FPD), a lot of design methods are being deployed, including OLED, PDP, TFT-LCD, Back Projection and Field Emission Display(FED) etc. These new generation FPDs have their respective pluses and minuses. Each has its selling points and market attractions. But among them, FED principles are most close to that of CRT displays. Not only FEDs are advantageous in their good degree of saturation of color, but also they have excellent contrast, luminance and electricity consumption etc. It has been considered as the main products of future generation FPDs. Japan and countries all over the world are successively proposing and launching related FED products in the fields. This will not only drive the FEDs into a wave of new trends, but also it will be able to replace most of the current FPD products within a short time. In this paper, based on these solid trends, we are determined to put into our resources and efforts to perform research on these important FEDs technologies and products, particularly in Carbon Nano-Tubes FEDs(CNT-FED). Our research group has already performed research on CNT-FED subjects for almost three years. During the course of our research, we have run into a lot of issues and problems. We have made every effort to overcome some of them. This paper performs comparative analysis of three power option for small size (4-inch) CNT-FEDs to drive the FED effects such as the direct current power, pulsed power and sinusoidal power respectively. This paper performs comparative analysis of three power options for small sized CNT-FEDs. It was concluded that the pulsed power option will produce the best results overall among the three power options. It is felt that these data presented can then be referenced and used to design a power system circuit to get an optimum design for better luminance and least power consumption for small sized commercial CNT-FED products.

Lot quality assurance sampling (LQAS) for monitoring a leprosy elimination program.

PubMed

Gupte, M D; Narasimhamurthy, B

1999-06-01

In a statistical sense, prevalences of leprosy in different geographical areas can be called very low or rare. Conventional survey methods to monitor leprosy control programs, therefore, need large sample sizes, are expensive, and are time-consuming. Further, with the lowering of prevalence to the near-desired target level, 1 case per 10,000 population at national or subnational levels, the program administrator's concern will be shifted to smaller areas, e.g., districts, for assessment and, if needed, for necessary interventions. In this paper, Lot Quality Assurance Sampling (LQAS), a quality control tool in industry, is proposed to identify districts/regions having a prevalence of leprosy at or above a certain target level, e.g., 1 in 10,000. This technique can also be considered for identifying districts/regions at or below the target level of 1 per 10,000, i.e., areas where the elimination level is attained. For simulating various situations and strategies, a hypothetical computerized population of 10 million persons was created. This population mimics the actual population in terms of the empirical information on rural/urban distributions and the distribution of households by size for the state of Tamil Nadu, India. Various levels with respect to leprosy prevalence are created using this population. The distribution of the number of cases in the population was expected to follow the Poisson process, and this was also confirmed by examination. Sample sizes and corresponding critical values were computed using Poisson approximation. Initially, villages/towns are selected from the population and from each selected village/town households are selected using systematic sampling. Households instead of individuals are used as sampling units. This sampling procedure was simulated 1000 times in the computer from the base population. The results in four different prevalence situations meet the required limits of Type I error of 5% and 90% Power. It is concluded that after validation under field conditions, this method can be considered for a rapid assessment of the leprosy situation.

Multiple Category-Lot Quality Assurance Sampling: A New Classification System with Application to Schistosomiasis Control

PubMed Central

Olives, Casey; Valadez, Joseph J.; Brooker, Simon J.; Pagano, Marcello

2012-01-01

Background Originally a binary classifier, Lot Quality Assurance Sampling (LQAS) has proven to be a useful tool for classification of the prevalence of Schistosoma mansoni into multiple categories (≤10%, >10 and <50%, ≥50%), and semi-curtailed sampling has been shown to effectively reduce the number of observations needed to reach a decision. To date the statistical underpinnings for Multiple Category-LQAS (MC-LQAS) have not received full treatment. We explore the analytical properties of MC-LQAS, and validate its use for the classification of S. mansoni prevalence in multiple settings in East Africa. Methodology We outline MC-LQAS design principles and formulae for operating characteristic curves. In addition, we derive the average sample number for MC-LQAS when utilizing semi-curtailed sampling and introduce curtailed sampling in this setting. We also assess the performance of MC-LQAS designs with maximum sample sizes of n = 15 and n = 25 via a weighted kappa-statistic using S. mansoni data collected in 388 schools from four studies in East Africa. Principle Findings Overall performance of MC-LQAS classification was high (kappa-statistic of 0.87). In three of the studies, the kappa-statistic for a design with n = 15 was greater than 0.75. In the fourth study, where these designs performed poorly (kappa-statistic less than 0.50), the majority of observations fell in regions where potential error is known to be high. Employment of semi-curtailed and curtailed sampling further reduced the sample size by as many as 0.5 and 3.5 observations per school, respectively, without increasing classification error. Conclusion/Significance This work provides the needed analytics to understand the properties of MC-LQAS for assessing the prevalance of S. mansoni and shows that in most settings a sample size of 15 children provides a reliable classification of schools. PMID:22970333

Measurement of Dynamic Viscoelasticity of Full-Size Wood Composite Panels Using a Vibration Testing Method

Treesearch

Cheng Guan; Houjiang Zhang; John F. Hunt; Lujing Zhou; Dan Feng

2016-01-01

The dynamic viscoelasticity of full-size wood composite panels (WCPs) under the free-free vibrational state were determined by a vibration testing method. Vibration detection tests were performed on 194 pieces of three types of full-size WCPs (particleboard, medium density fiberboard, and plywood (PW)). The dynamic viscoelasticity from smaller specimens cut from the...

77 FR 39726 - Land Acquisitions: Pueblo of Santa Clara

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-05

... Indian Affairs, 1001 Indian School Road NW., Albuquerque, NM 87104-2303; Telephone (505) 563-3337, sandy...., Sec. 17, lots 1 to 8, inclusive; Sec. 18, lots 5 to 12, inclusive; Sec. 19, lots 12 to 17, inclusive...

Field performance of a porous asphaltic pavement.

DOT National Transportation Integrated Search

1992-01-01

The Virginia Department of Transportation constructed a 2.52-acre parking lot of porous asphaltic pavement in Warrenton, Virginia. Runoff from the lot was collected and monitored for quantity, detention time, and quality. Prior to the lot opening for...

Insecticides: effects on cutthroat trout of repeated exposure to DDT

USGS Publications Warehouse

Allison, Don; Kallman, Burton J.; Cope, Oliver B.; Van Valin, Charles C.

1963-01-01

Cutthroat trout were periodically exposed to p, pp-DDT, in acetone solution or in the food. Excessive mortality occurred only in lots treated with high concentrations of DDT, probably as a result of decreased resistance to nonspecific stressors. Surviving fish in these lots were significantly larger than those in the control lot, or in the lots treated with low concentrations of DDT. The number and volume of eggs produced was not reduced by DDT, but mortality among sac fry appeared to be highest in the lots treated with high concentrations. The data suggest that the sublethal concentrations of DDT ordinarily encountered in the environment are unlikely to damage a fishery.

Predation risk suppresses the positive feedback between size structure and cannibalism.

PubMed

Kishida, Osamu; Trussell, Geoffrey C; Ohno, Ayaka; Kuwano, Shinya; Ikawa, Takuya; Nishimura, Kinya

2011-11-01

1. Cannibalism can play a prominent role in the structuring and dynamics of ecological communities. Previous studies have emphasized the importance of size structure and density of cannibalistic species in shaping short- and long-term cannibalism dynamics, but our understanding of how predators influence cannibalism dynamics is limited. This is despite widespread evidence that many prey species exhibit behavioural and morphological adaptations in response to predation risk. 2. This study examined how the presence and absence of predation risk from larval dragonflies Aeshna nigroflava affected cannibalism dynamics in its prey larval salamanders Hynobius retardatus. 3. We found that feedback dynamics between size structure and cannibalism depended on whether dragonfly predation risk was present. In the absence of dragonfly risk cues, a positive feedback between salamander size structure and cannibalism through time occurred because most of the replicates in this treatment contained at least one salamander larvae having an enlarged gape (i.e. cannibal). In contrast, this feedback and the emergence of cannibalism were rarely observed in the presence of the dragonfly risk cues. Once salamander size divergence occurred, experimental reversals of the presence or absence of dragonfly risk cues did not alter existing cannibalism dynamics as the experiment progressed. Thus, the effects of risk on the mechanisms driving cannibalism dynamics likely operated during the early developmental period of the salamander larvae. 4. The effects of dragonfly predation risk on behavioural aspects of cannibalistic interactions among hatchlings may prohibit the initiation of dynamics between size structure and cannibalism. Our predation trials clearly showed that encounter rates among hatchlings and biting and ingestion rates of prospective prey by prospective cannibals were significantly lower in the presence vs. absence of dragonfly predation risk even though the size asymmetry between cannibals and victims was similar in both risk treatments. These results suggest that dragonfly risk cues first suppress cannibalism among hatchlings and then prevent size variation from increasing through time. 5. We suggest that the positive feedback dynamics between size structure and cannibalism and their modification by predation risk may also operate in other systems to shape the population dynamics of cannibalistic prey species as well as overall community dynamics. © 2011 The Authors. Journal of Animal Ecology © 2011 British Ecological Society.

Clustered lot quality assurance sampling: a pragmatic tool for timely assessment of vaccination coverage.

PubMed

Greenland, K; Rondy, M; Chevez, A; Sadozai, N; Gasasira, A; Abanida, E A; Pate, M A; Ronveaux, O; Okayasu, H; Pedalino, B; Pezzoli, L

2011-07-01

To evaluate oral poliovirus vaccine (OPV) coverage of the November 2009 round in five Northern Nigeria states with ongoing wild poliovirus transmission using clustered lot quality assurance sampling (CLQAS). We selected four local government areas in each pre-selected state and sampled six clusters of 10 children in each Local Government Area, defined as the lot area. We used three decision thresholds to classify OPV coverage: 75-90%, 55-70% and 35-50%. A full lot was completed, but we also assessed in retrospect the potential time-saving benefits of stopping sampling when a lot had been classified. We accepted two local government areas (LGAs) with vaccination coverage above 75%. Of the remaining 18 rejected LGAs, 11 also failed to reach 70% coverage, of which four also failed to reach 50%. The average time taken to complete a lot was 10 h. By stopping sampling when a decision was reached, we could have classified lots in 5.3, 7.7 and 7.3 h on average at the 90%, 70% and 50% coverage targets, respectively. Clustered lot quality assurance sampling was feasible and useful to estimate OPV coverage in Northern Nigeria. The multi-threshold approach provided useful information on the variation of IPD vaccination coverage. CLQAS is a very timely tool, allowing corrective actions to be directly taken in insufficiently covered areas. © 2011 Blackwell Publishing Ltd.

Complete study demonstrating the absence of rhabdovirus in a distinct Sf9 cell line.

PubMed

Hashimoto, Yoshifumi; Macri, Daniel; Srivastava, Indresh; McPherson, Clifton; Felberbaum, Rachael; Post, Penny; Cox, Manon

2017-01-01

A putative novel rhabdovirus (SfRV) was previously identified in a Spodoptera frugiperda cell line (Sf9 cells [ATCC CRL-1711 lot 58078522]) by next generation sequencing and extensive bioinformatic analysis. We performed an extensive analysis of our Sf9 cell bank (ATCC CRL-1711 lot 5814 [Sf9L5814]) to determine whether this virus was already present in cells obtained from ATCC in 1987. Inverse PCR of DNA isolated from Sf9 L5814 cellular DNA revealed integration of SfRV sequences in the cellular genome. RT-PCR of total RNA showed a deletion of 320 nucleotides in the SfRV RNA that includes the transcriptional motifs for genes X and L. Concentrated cell culture supernatant was analyzed by sucrose density gradient centrifugation and revealed a single band at a density of 1.14 g/ml. This fraction was further analysed by electron microscopy and showed amorphous and particulate debris that did not resemble a rhabdovirus in morphology or size. SDS-PAGE analysis confirmed that the protein composition did not contain the typical five rhabdovirus structural proteins and LC-MS/MS analysis revealed primarily of exosomal marker proteins, the SfRV N protein, and truncated forms of SfRV N, P, and G proteins. The SfRV L gene fragment RNA sequence was recovered from the supernatant after ultracentrifugation of the 1.14 g/ml fraction treated with diethyl ether suggesting that the SfRV L gene fragment sequence is not associated with a diethyl ether resistant nucleocapsid. Interestingly, the 1.14 g/ml fraction was able to transfer baculovirus DNA into Sf9L5814 cells, consistent with the presence of functional exosomes. Our results demonstrate the absence of viral particles in ATCC CRL-1711 lot 5814 Sf9 cells in contrast to a previous study that suggested the presence of infectious rhabdoviral particles in Sf9 cells from a different lot. This study highlights how cell lines with different lineages may present different virosomes and therefore no general conclusions can be drawn across Sf9 cells from different laboratories.

Parking Lot Runoff Quality and Treatment Efficiency of a Stormwater-Filtration Device, Madison, Wisconsin, 2005-07

USGS Publications Warehouse

Horwatich, Judy A.; Bannerman, Roger T.

2010-01-01

To evaluate the treatment efficiency of a stormwater-filtration device (SFD) for potential use at Wisconsin Department of Transportation (WisDOT) park-and-ride facilities, a SFD was installed at an employee parking lot in downtown Madison, Wisconsin. This type of parking lot was chosen for the test site because the constituent concentrations and particle-size distributions (PSDs) were expected to be similar to those of a typical park-and-ride lot operated by WisDOT. The objective of this particular installation was to reduce loads of total suspended solids (TSS) in stormwater runoff to Lake Monona. This study also was designed to provide a range of treatment efficiencies expected for a SFD. Samples from the inlet and outlet were analyzed for 33 organic and inorganic constituents, including 18 polycyclic aromatic hydrocarbons (PAHs). Samples were also analyzed for physical properties, including PSD. Water-quality samples were collected for 51 runoff events from November 2005 to August 2007. Samples from all runoff events were analyzed for concentrations of suspended sediment (SS). Samples from 31 runoff events were analyzed for 15 constituents, samples from 15 runoff events were analyzed for PAHs, and samples from 36 events were analyzed for PSD. The treatment efficiency of the SFD was calculated using the summation of loads (SOL) and the efficiency ratio methods. Constituents for which the concentrations and (or) loads were decreased by the SFD include TSS, SS, volatile suspended solids, total phosphorous (TP), total copper, total zinc, and PAHs. The efficiency ratios for these constituents are 45, 37, 38, 55, 22, 5, and 46 percent, respectively. The SOLs for these constituents are 32, 37, 28, 36, 23, 8, and 48 percent, respectively. The SOL for chloride was -21 and the efficiency ratio was -18. Six chemical constituents or properties-dissolved phosphorus, chemical oxygen demand, dissolved zinc, total dissolved solids, dissolved chemical oxygen demand, and dissolved copper-were not included in the efficiency or SOL, because the difference between concentrations in samples from the inlet and outlet were not significant. Concentrations of TP and TSS were inexplicably high in samples at the inlet for one event.

Density Distributions of Cyclotrimethylenetrinitramines (RDX)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, D M

2002-03-19

As part of the US Army Foreign Comparative Testing (FCT) program the density distributions of six samples of class 1 RDX were measured using the density gradient technique. This technique was used in an attempt to distinguish between RDX crystallized by a French manufacturer (designated insensitive or IRDX) from RDX manufactured at Holston Army Ammunition Plant (HAAP), the current source of RDX for Department of Defense (DoD). Two samples from different lots of French IRDX had an average density of 1.7958 {+-} 0.0008 g/cc. The theoretical density of a perfect RDX crystal is 1.806 g/cc. This yields 99.43% of themore » theoretical maximum density (TMD). For two HAAP RDX lots the average density was 1.786 {+-} 0.002 g/cc, only 98.89% TMD. Several other techniques were used for preliminary characterization of one lot of French IRDX and two lot of HAAP RDX. Light scattering, SEM and polarized optical microscopy (POM) showed that SNPE and Holston RDX had the appropriate particle size distribution for Class 1 RDX. High performance liquid chromatography showed quantities of HMX in HAAP RDX. French IRDX also showed a 1.1 C higher melting point compared to HAAP RDX in the differential scanning calorimetry (DSC) consistent with no melting point depression due to the HMX contaminant. A second part of the program involved characterization of Holston RDX recrystallized using the French process. After reprocessing the average density of the Holston RDX was increased to 1.7907 g/cc. Apparently HMX in RDX can act as a nucleating agent in the French RDX recrystallization process. The French IRDX contained no HMX, which is assumed to account for its higher density and narrower density distribution. Reprocessing of RDX from Holston improved the average density compared to the original Holston RDX, but the resulting HIRDX was not as dense as the original French IRDX. Recrystallized Holston IRDX crystals were much larger (3-500 {micro}m or more) then either the original class 1 HAAP RDX or French IRDX.« less

Smart factory in the context of 4th industrial revolution: challenges and opportunities for Romania

NASA Astrophysics Data System (ADS)

Pîrvu, B. C.; Zamfirescu, C. B.

2017-08-01

Manufacturing companies, independent of operation sector and size, must be able to produce lot size one products, just-in-time at a competitive cost. Coping with this high adaptability and short reaction times proves to be very challenging. New approaches must be taken into consideration for designing modular, intelligent and cooperative production systems which are easy to integrate with the entire factory. The coined term for this network of intelligent interacting artefacts system is cyber-physical systems (CPS). CPS is often used in the context of Industry 4.0 - or what many consider the forth industrial revolution. The paper presents an overview of key technological and social requirements to map the Smart Factory vision into reality. Finally, global and Romanian specific challenges hindering the vision of a true Smart Factory to become reality are presented.

Development and Applications of Laminar Optical Tomography for In Vivo Imaging

NASA Astrophysics Data System (ADS)

Burgess, Sean A.

Laminar optical tomography (LOT) is an optical imaging technique capable of making depth-resolved measurements of absorption and fluorescence contrast in scattering tissue. LOT was first demonstrated in 2004 by Hillman et al [1]. The technique combines a non-contact laser scanning geometry, similar to a low magnification confocal microscope, with the imaging principles of diffuse optical tomography (DOT). This thesis describes the development and application of a second generation LOT system, which acquires both fluorescence and multi-wavelength measurements simultaneously and is better suited for in vivo measurements. Chapter 1 begins by reviewing the interactions of light with tissue that form the foundation of optical imaging. A range of related optical imaging techniques and the basic principles of LOT imaging are then described. In Chapter 2, the development of the new LOT imaging system is described including the implementation of a series of interfaces to allow clinical imaging. System performance is then evaluated on a range of imaging phantoms. Chapter 3 describes two in vivo imaging applications explored using the second generation LOT system, first in a clinical setting where skin lesions were imaged, and then in a laboratory setting where LOT imaging was performed on exposed rat cortex. The final chapter provides a brief summary and describes future directions for LOT. LOT has the potential to find applications in medical diagnostics, surgical guidance, and in-situ monitoring owing to its sensitivity to absorption and fluorescence contrast as well as its ability to provide depth sensitive measures. Optical techniques can characterize blood volume and oxygenation, two important biological parameters, through measurements at different wavelengths. Fluorescence measurements, either from autofluorescence or fluorescent dyes, have shown promise for identifying and analyzing lesions in various epithelial tissues including skin [2, 3], colon [4], esophagus [5, 6], oral mucosa [7, 8], and cervix [9]. The desire to capture these types of measurements with LOT motivated much of the work presented here.

Grain size evolution and convection regimes of the terrestrial planets

NASA Astrophysics Data System (ADS)

Rozel, A.; Golabek, G. J.; Boutonnet, E.

2011-12-01

A new model of grain size evolution has recently been proposed in Rozel et al. 2010. This new approach stipulates that the grain size dynamics is governed by two additive and simultaneous processes: grain growth and dynamic recrystallization. We use the usual normal grain growth laws for the growth part. For dynamic recrystallization, reducing the mean grain size increases the total area of grain boundaries. Grain boundaries carry some surface tension, so some energy is required to decrease the mean grain size. We consider that this energy is available during mechanical work. It is usually considered to produce some heat via viscous dissipation. A partitioning parameter f is then required to know what amount of energy is dissipated and what part is converted in surface tension. This study gives a new calibration of the partitioning parameter on major Earth materials involved in the dynamic of the terrestrial planets. Our calibration is in adequation with the published piezometric relations available in the literature (equilibrium grain size versus shear stress). We test this new model of grain size evolution in a set of numerical computations of the dynamics of the Earth using stagYY. We show that the grain size evolution has a major effect on the convection regimes of terrestrial planets.

Cpu/gpu Computing for AN Implicit Multi-Block Compressible Navier-Stokes Solver on Heterogeneous Platform

NASA Astrophysics Data System (ADS)

Deng, Liang; Bai, Hanli; Wang, Fang; Xu, Qingxin

2016-06-01

CPU/GPU computing allows scientists to tremendously accelerate their numerical codes. In this paper, we port and optimize a double precision alternating direction implicit (ADI) solver for three-dimensional compressible Navier-Stokes equations from our in-house Computational Fluid Dynamics (CFD) software on heterogeneous platform. First, we implement a full GPU version of the ADI solver to remove a lot of redundant data transfers between CPU and GPU, and then design two fine-grain schemes, namely “one-thread-one-point” and “one-thread-one-line”, to maximize the performance. Second, we present a dual-level parallelization scheme using the CPU/GPU collaborative model to exploit the computational resources of both multi-core CPUs and many-core GPUs within the heterogeneous platform. Finally, considering the fact that memory on a single node becomes inadequate when the simulation size grows, we present a tri-level hybrid programming pattern MPI-OpenMP-CUDA that merges fine-grain parallelism using OpenMP and CUDA threads with coarse-grain parallelism using MPI for inter-node communication. We also propose a strategy to overlap the computation with communication using the advanced features of CUDA and MPI programming. We obtain speedups of 6.0 for the ADI solver on one Tesla M2050 GPU in contrast to two Xeon X5670 CPUs. Scalability tests show that our implementation can offer significant performance improvement on heterogeneous platform.

On the possibility to develop an advanced non-equilibrium model of depressurisation in two-phase fluids

NASA Astrophysics Data System (ADS)

Duc, Linh Do; Horák, Vladimír; Kulish, Vladimir; Lukáč, Tomáš

2017-01-01

Carbon dioxide is widely used as the power gas in the gas guns community due to its ease of handling, storability at room temperature, and high vapor pressure depending only upon temperature, but not a tank size, as long as some liquid carbon dioxide remains in the tank. This high vapor pressure can be used as the pressurant, making it what is referred to as a self-pressurising propellant. However, as a two-phase substance, carbon dioxide does have its drawbacks: (1) vaporization of liquefied CO2 inside a tank when shooting rapidly or a lot causes the tank to get cool, resulting in pressure fluctuations that makes the gun's performance and accuracy worse, (2) solid carbon dioxide that is also known as dry ice can appear on the output valve of the tank while shooting and it can cause damage or slow the gun's performance down, if it works its way into some control components, including the barrel of the gun. Hence, it is crucial to obtain a scientific understanding of carbon dioxide behavior and further the discharge characteristics of a wide range of pressure-tank configurations. For the purpose of satisfying this goal, a comprehensive discharge mathematical model for carbon dioxide tank dynamics is required. In this paper, the possibility to develop an advanced non-equilibrium model of depressurization in two-phase fluids is discussed.

Laser-assisted biosynthesis for noble nanoparticles production

NASA Astrophysics Data System (ADS)

Kukhtarev, Tatiana; Edwards, Vernessa; Kukhtareva, Nickolai; Moses, Sherita

2014-08-01

Extracellular Biosynthesis technique (EBS) for nanoparticles production has attracted a lot of attention as an environmentally friendly and an inexpensive methodology. Our recent research was focused on the rapid approach of the green synthesis method and the reduction of the homogeneous size distribution of nanoparticles using pulse laser application. Noble nanoparticles (NNPs) were produced using various ethanol and water plant extracts. The plants were chosen based on their biomedical applications. The plants we used were Magnolia grandiflora, Geranium, Aloe `tingtinkie', Aloe barbadensis (Aloe Vera), Eucalyptus angophoroides, Sansevieria trifasciata, Impatiens scapiflora. Water and ethanol extract, were used as reducing agents to produce the nanoparticles. The reaction process was monitored using a UV-Visible spectroscopy. NNPs were characterized by Fourier Transfer Infrared Spectroscopy (FTIR), Transmission Electron Microscopy (TEM), and the Dynamic Light Scattering technique (DLS). During the pulse laser Nd-YAG illumination (λ=1064nm, 532nm, PE= 450mJ, 200mJ, 10 min) the blue shift of the surface plasmon resonance absorption peak was observed from ~424nm to 403nm for silver NP; and from ~530nm to 520 nm for gold NPs. In addition, NNPs solution after Nd-YAG illumination was characterized by the narrowing of the surface plasmon absorption resonance band, which corresponds to monodispersed NNPS distribution. FTIR, TEM, DLS, Zeta potential results demonstrated that NNPs were surrounded by biological molecules, which naturally stabilized nanosolutions for months. Cytotoxicity investigation of biosynthesized NNPs is in progress.

7 CFR 983.52 - Failed lots/rework procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Regulations § 983.52 Failed lots/rework procedure. (a) Substandard pistachios. Each lot of substandard pistachios may be reworked to meet aflatoxin or quality requirements. The...

1. Context view showing cabin on Lot 2 in foreground ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Context view showing cabin on Lot 2 in foreground (17419 North Shore Drive) and east side of Frank-Jensen Summer Home on Lot 3 in background. - Frank-Jensen Summer Home, 17423 North Lake Shore Drive, Telma, Chelan County, WA

Joint Air-to-Surface Standoff Missile (JASSM)

DTIC Science & Technology

2015-12-01

6.1.3) All Ops All Ops Joint Critical Ops All Ops All Ops Missile Reliability (KSA) (CPD para 6.2.8) 4th Lot .91 4th Lot .91 IOT &E .80 4th Lot .85 IOT &E...the ORD 303-95-III dated January 20, 2004 Change Explanations None Acronyms and Abbreviations IOT &E - Initial Operational Test and Evaluation KSA... Actuator Control Card, Lots 12 and 4 Systems Engineering Program Support/Program Tooling and Test Equipment, and JASSM-ER Standard Data Protocol (DS

Exotic nuclear systems with strangeness: Hypernuclei and Kaonic nuclei

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dote, Akinobu

2010-05-12

Nuclear systems with strangeness, hypernuclei and kaonic nuclei, are expected to have lots of interesting properties. In this article, after the recent development of hypernuclear study is reviewed, we report two results of our study of hypernuclei with antisymmetrized molecular dynamics; 1) impurity effect of LAMBDA on {sub L}AMBDA{sup 20}Ne, and 2){sub X}I{sup 12}Be studied with three kinds of XIN potentials. The current status of studies of kaonic nuclei is also introduced and our study with a phenomenological and a chiral-based K-barN potential are reported.

Tritium safety study using Caisson Assembly (CATS) at TPL/JAEA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hayashi, T.; Kobayashi, K.; Iwai, Y.

Tritium confinement is required as the most important safety Junction for a fusion reactor. In order to demonstrate the confinement performance experimentally, an unique equipment, called CATS: Caisson Assembly for Tritium Safety study, was installed in Tritium Process Laboratory of Japan Atomic Energy Agency and operated for about 10 years. Tritium confinement and migration data in CATS have been accumulated and dynamic simulation code was accumulated using these data. Contamination and decontamination behavior on various materials and new safety equipment functions have been investigated under collaborations with a lot of laboratories and universities. (authors)

Assumptions of acceptance sampling and the implications for lot contamination: Escherichia coli O157 in lots of Australian manufacturing beef.

PubMed

Kiermeier, Andreas; Mellor, Glen; Barlow, Robert; Jenson, Ian

2011-04-01

The aims of this work were to determine the distribution and concentration of Escherichia coli O157 in lots of beef destined for grinding (manufacturing beef) that failed to meet Australian requirements for export, to use these data to better understand the performance of sampling plans based on the binomial distribution, and to consider alternative approaches for evaluating sampling plans. For each of five lots from which E. coli O157 had been detected, 900 samples from the external carcass surface were tested. E. coli O157 was not detected in three lots, whereas in two lots E. coli O157 was detected in 2 and 74 samples. For lots in which E. coli O157 was not detected in the present study, the E. coli O157 level was estimated to be <12 cells per 27.2-kg carton. For the most contaminated carton, the total number of E. coli O157 cells was estimated to be 813. In the two lots in which E. coli O157 was detected, the pathogen was detected in 1 of 12 and 2 of 12 cartons. The use of acceptance sampling plans based on a binomial distribution can provide a falsely optimistic view of the value of sampling as a control measure when applied to assessment of E. coli O157 contamination in manufacturing beef. Alternative approaches to understanding sampling plans, which do not assume homogeneous contamination throughout the lot, appear more realistic. These results indicate that despite the application of stringent sampling plans, sampling and testing approaches are inefficient for controlling microbiological quality.

Strong fluctuations in aboveground population size do not limit genetic diversity in populations of an endangered biennial species.

PubMed

Münzbergová, Zuzana; Šurinová, Maria; Husáková, Iveta; Brabec, Jiří

2018-04-26

Assessing genetic diversity within populations of rare species and understanding its determinants are crucial for effective species protection. While a lot is known about the relationships between genetic diversity, fitness, and current population size, very few studies explored the effects of past population size. Knowledge of past population size may, however, improve our ability to predict future population fates. We studied Gentianella praecox subsp. bohemica, a biennial species with extensive seed bank. We tested the effect of current, past minimal and maximal population size, and harmonic mean of population sizes within the last 15 years on genetic diversity and fitness. Maximum population size over the last 15 years was the best predictor of expected heterozygosity of the populations and was significantly related to current population size and management. Plant fitness was significantly related to current as well as maximum population size and expected heterozygosity. The results suggested that information on past population size may improve our understanding of contemporary genetic diversity across populations. They demonstrated that despite the strong fluctuations in population size, large reductions in population size do not result in immediate loss of genetic diversity and reduction of fitness within the populations. This is likely due to the seed bank of the species serving as reservoir of the genetic diversity of the populations. From a conservation point of view, this suggests that the restoration of small populations of short-lived species with permanent seed bank is possible as these populations may still be genetically diverse.

Dynamic properties of epidemic spreading on finite size complex networks

NASA Astrophysics Data System (ADS)

Li, Ying; Liu, Yang; Shan, Xiu-Ming; Ren, Yong; Jiao, Jian; Qiu, Ben

2005-11-01

The Internet presents a complex topological structure, on which computer viruses can easily spread. By using theoretical analysis and computer simulation methods, the dynamic process of disease spreading on finite size networks with complex topological structure is investigated. On the finite size networks, the spreading process of SIS (susceptible-infected-susceptible) model is a finite Markov chain with an absorbing state. Two parameters, the survival probability and the conditional infecting probability, are introduced to describe the dynamic properties of disease spreading on finite size networks. Our results can help understanding computer virus epidemics and other spreading phenomena on communication and social networks. Also, knowledge about the dynamic character of virus spreading is helpful for adopting immunity policy.

7 CFR 42.103 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... CONDITION OF FOOD CONTAINERS Procedures for Stationary Lot Sampling and Inspection § 42.103 Purpose and... stationary lots of packaged foods. This subpart shall be used to determine the acceptability of a lot based...

7 CFR 42.141 - Obtaining Operating Characteristic (OC) curve information for skip lot sampling and inspection.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., and read the new Percent of Lots Expected to be Accepted, Pas, which results when using these skip lot... point, proceed vertically to the curve and then horizontally to the left to the vertical axis. From this...

7 CFR 42.141 - Obtaining Operating Characteristic (OC) curve information for skip lot sampling and inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., and read the new Percent of Lots Expected to be Accepted, Pas, which results when using these skip lot... point, proceed vertically to the curve and then horizontally to the left to the vertical axis. From this...

Homogeneity of GAFCHROMIC EBT2 film among different lot numbers

PubMed Central

Takahashi, Yutaka; Tanaka, Atsushi; Hirayama, Takamitsu; Yamaguchi, Tsuyoshi; Katou, Hiroaki; Takahara, Keiko; Okamoto, Yoshiaki; Teshima, Teruki

2012-01-01

EBT2 film is widely used for quality assurance in radiation therapy. The purpose of this study was to investigate the homogeneity of EBT2 film among various lots, and the dose dependence of heterogeneity. EBT2 film was positioned in the center of a flatbed scanner and scanned in transmission mode at 75 dpi. Homogeneity was investigated by evaluating gray value and net optical density (netOD) with the red color channel. The dose dependence of heterogeneity in a single sheet from five lots was investigated at 0.5, 2, and 3 Gy. Maximum coefficient of variation as evaluated by netOD in a single film was 3.0% in one lot, but no higher than 0.5% in other lots. Dose dependence of heterogeneity was observed on evaluation by gray value but not on evaluation by netOD. These results suggest that EBT2 should be examined in each lot number before clinical use, and that the dose calibration curve should be constructed using netOD. PACS number: 87 PMID:22766947

Susceptibility to Cracking of Different Lots of CDR35 Capacitors

NASA Technical Reports Server (NTRS)

Teverovsky, Alexander

2017-01-01

On-orbit flight anomalies that occurred after several months of operation were attributed to excessive leakage currents in CDR35 style 0.47 microF 50 V capacitors operating at 10 V. In this work, a lot of capacitors similar to the lot that caused the anomaly have been evaluated in parallel with another lot of similar parts to assess their susceptibility to cracking under manual soldering conditions and get insight into a possible mechanism of failure. Leakage currents in capacitors were monitored at different voltages and environmental conditions before and after terminal solder dip testing that was used to simulate thermal shock during manual soldering. Results of cross-sectioning, acoustic microscopy, and measurements of electrical and mechanical characteristics of the parts have been analyzed, and possible mechanisms of failures considered. It is shown that the susceptibility to cracking and failures caused by manual soldering is lot-related. Recommendations for testing that would help to select lots that are more robust against manual soldering stresses and mitigate the risk of failures suggested.

Polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in harbor sediments from Sea Lots, Port-of-Spain, Trinidad and Tobago

USGS Publications Warehouse

Mohammed, Azad; Peterman, Paul; Echols, Kathy; Feltz, Kevin; Tegerdine, George; Manoo, Anton; Maraj, Dexter; Agard, John; Orazio, Carl

2011-01-01

Concentrations of polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) were determined in nearshore marine surficial sediments from three locations in Trinidad. Sediments were sampled at Sea Lots on the west coast, in south Port-of-Spain Harbor, south of Sea Lots at Caroni Lagoon National Park, and on Trinidad's east coast at Manzanilla. Total PCB concentrations in Sea Lots sediments ranged from 62 to 601 ng/g (dry weight {dw}), which was higher than at Caroni and Manzanilla, 13 and 8 ng/g dw, respectively. Total OCP concentrations at Sea Lots were ranged from 44.5 to 145 ng/g dw, compared with 13.1 and 23.8 n/g (dw), for Caroni and Manzanilla respectively. The concentrations of PCBs and of some OCPs in sediments from Sea Lots were above the Canadian interim sediment quality guidelines. To date, this data is the first report on the levels of PCBs and other organochlorine compounds from Trinidad and Tobago.

It's not football.

PubMed

Ryan, G

1998-01-01

Today I am as happy as I could ever be. I have created a lot out of very little, I have worked full time, played full time, got full-time friends, full-time independence, had full-time love and am lucky enough to be with my new full-time love who helps me a great deal both physically and mentally. It is definitely no fun coughing until your chest is sore in the morning, afternoon and evening. Having wringing night-sweats from cepacia. Wanting to sleep more than Mr Sleep from Sleepland. Taking tablets the size of which sunk the Belgrano. Finding time for physiotherapy, eating the right meals, playing on my Playstation. Depression has got through on previous occasions, but not for long, and it has never resulted in anything more than a 'wake up and smell the coffee' call from myself. Having CF is no ball game (otherwise it would be called football or something!), but I have had a lot of fun and will continue to do so for however long. Two years, five years, 20 years--who's to say, not me. We could all have the same left, I just hope that everyone has as much fun.

Lot quality assurance sampling for screening communities hyperendemic for Schistosoma mansoni.

PubMed

Rabarijaona, L P; Boisier, P; Ravaoalimalala, V E; Jeanne, I; Roux, J F; Jutand, M A; Salamon, R

2003-04-01

Lot quality assurance sampling (LQAS) was evaluated for rapid low cost identification of communities where Schistosoma mansoni infection was hyperendemic in southern Madagascar. In the study area, S. mansoni infection shows very focused and heterogeneous distribution requiring multifariousness of local surveys. One sampling plan was tested in the field with schoolchildren and several others were simulated in the laboratory. Randomization and stool specimen collection were performed by voluntary teachers under direct supervision of the study staff and no significant problem occurred. As expected from Receiver Operating Characteristic (ROC) curves, all sampling plans allowed correct identification of hyperendemic communities and of most of the hypoendemic ones. Frequent misclassifications occurred for communities with intermediate prevalence and the cheapest plans had very low specificity. The study confirmed that LQAS would be a valuable tool for large scale screening in a country with scarce financial and staff resources. Involving teachers, appeared to be quite feasible and should not lower the reliability of surveys. We recommend that the national schistosomiasis control programme systematically uses LQAS for identification of communities, provided that sample sizes are adapted to the specific epidemiological patterns of S. mansoni infection in the main regions.

Diagnostic Accuracy and Feasibility of Serological Tests on Filter Paper Samples for Outbreak Detection of T.b. gambiense Human African Trypanosomiasis

PubMed Central

Hasker, Epco; Lutumba, Pascal; Mumba, Dieudonné; Lejon, Veerle; Büscher, Phillipe; Kande, Victor; Muyembe, Jean Jacques; Menten, Joris; Robays, Jo; Boelaert, Marleen

2010-01-01

Control of human African trypanosomiasis (HAT) in the Democratic Republic of Congo is based on mass population screening by mobile teams; a costly and labor-intensive approach. We hypothesized that blood samples collected on filter paper by village health workers and processed in a central laboratory might be a cost-effective alternative. We estimated sensitivity and specificity of micro-card agglutination test for trypanosomiasis (micro-CATT) and enzyme-linked immunosorbent assay (ELISA)/T.b. gambiense on filter paper samples compared with parasitology-based case classification and used the results in a Monte Carlo simulation of a lot quality assurance sampling (LQAS) approach. Micro-CATT and ELISA/T.b. gambiense showed acceptable sensitivity (92.7% [95% CI 87.4–98.0%] and 82.2% [95% CI 75.3–90.4%]) and very high specificity (99.4% [95% CI 99.0–99.9%] and 99.8% [95% CI 99.5–100%]), respectively. Conditional on high sample size per lot (≥ 60%), both tests could reliably distinguish a 2% from a zero prevalence at village level. Alternatively, these tests could be used to identify individual HAT suspects for subsequent confirmation. PMID:20682885

The Development of Novel Recombinant Human Gelatins as Replacements for Animal-Derived Gelatin in Pharmaceutical Applications

NASA Astrophysics Data System (ADS)

Olsen, David; Chang, Robert; Williams, Kim E.; Polarek, James W.

We have developed a recombinant expression system to produce a series of novel recombinant human gelatins that can substitute for animal sourced gelatin preparations currently used in pharmaceutical and nutraceutical applications. This system allows the production of human sequence gelatins, or, if desired, gelatins from any other species depending on the availability of the cloned gene. The gelatins produced with this recombinant system are of defined molecular weight, unlike the animal-sourced gelatins, which consist of numerous polypeptides of varying size. The fermentation and purification process used to prepare these recombinant gelatins does not use any human- or animal-derived components and thus this recombinant material should be free from viruses and agents that cause transmissible spongiform encephalopathies. The recombinant gelatins exhibit lot-to-lot reproducibility and we have performed extensive analytical testing on them. We have demonstrated the utility of these novel gelatins as biological stabilizers and plasma expanders, and we have shown they possess qualities that are important in applications where gel formation is critical. Finally, we provide examples of how our system allows the engineering of these recombinant gelatins to optimize the production process.

Divergent sexual selection via male competition: ecology is key.

PubMed

Lackey, A C R; Boughman, J W

2013-08-01

Sexual selection and ecological differences are important drivers of speciation. Much research has focused on female choice, yet the role of male competition in ecological speciation has been understudied. Here, we test how mating habitats impact sexual selection and speciation through male competition. Using limnetic and benthic species of threespine stickleback fish, we find that different mating habitats select differently on male traits through male competition. In mixed habitat with both vegetated and open areas, selection favours two trait combinations of male body size and nuptial colour: large with little colour and small with lots of colour. This matches what we see in reproductively isolated stickleback species, suggesting male competition could promote trait divergence and reproductive isolation. In contrast, when only open habitat exists, selection favours one trait combination, large with lots of colour, which would hinder trait divergence and reproductive isolation. Other behavioural mechanisms in male competition that might promote divergence, such as avoiding aggression with heterospecifics, are insufficient to maintain separate species. This work highlights the importance of mating habitats in male competition for both sexual selection and speciation. © 2013 The Authors. Journal of Evolutionary Biology © 2013 European Society For Evolutionary Biology.

Emperical Tests of Acceptance Sampling Plans

NASA Technical Reports Server (NTRS)

White, K. Preston, Jr.; Johnson, Kenneth L.

2012-01-01

Acceptance sampling is a quality control procedure applied as an alternative to 100% inspection. A random sample of items is drawn from a lot to determine the fraction of items which have a required quality characteristic. Both the number of items to be inspected and the criterion for determining conformance of the lot to the requirement are given by an appropriate sampling plan with specified risks of Type I and Type II sampling errors. In this paper, we present the results of empirical tests of the accuracy of selected sampling plans reported in the literature. These plans are for measureable quality characteristics which are known have either binomial, exponential, normal, gamma, Weibull, inverse Gaussian, or Poisson distributions. In the main, results support the accepted wisdom that variables acceptance plans are superior to attributes (binomial) acceptance plans, in the sense that these provide comparable protection against risks at reduced sampling cost. For the Gaussian and Weibull plans, however, there are ranges of the shape parameters for which the required sample sizes are in fact larger than the corresponding attributes plans, dramatically so for instances of large skew. Tests further confirm that the published inverse-Gaussian (IG) plan is flawed, as reported by White and Johnson (2011).

[Method of fused sample preparation after nitrify-determination of primary and minor elements in manganese ore by X-ray fluorescence spectrometry].

PubMed

Song, Yi; Guo, Fen; Gu, Song-hai

2007-02-01

Eight components, i. e. Mn, SiO2, Fe, P, Al2O3, CaO, MgO and S, in manganese ore were determined by X-ray fluorescence spectrometer. Because manganese ore sample releases a lot of air bubbles during fusion which effect accuracy and reproducibility of determination, nitric acid was added to the sample to destroy organic matter before fusion by the mixture flux at 1000 degrees C. This method solved the problem that the flux splashed during fusion because organic matter volatilized brought out a lot of air bubbles, eliminated particle size effects and mineral effect, while solved the problem of volatilization of sulfur during fusion. The experiments for the selection of the sample preparation conditions, i. e. fusion flux, fusion time and volume of HNO3, were carried out. The matrix effects on absorption and enhancement were corrected by variable theoretical alpha coefficient to expand the range of determination. Moreover, the precision and accuracy experiments were performed. In comparison with chemical analysis method, the quantitative analytical results for each component are satisfactory. The method has proven rapid, precise and simple.

Neck blast disease influences grain yield and quality traits of aromatic rice.

PubMed

Khan, Mohammad Ashik Iqbal; Bhuiyan, Md Rejwan; Hossain, Md Shahadat; Sen, Partha Pratim; Ara, Anjuman; Siddique, Md Abubakar; Ali, Md Ansar

2014-11-01

A critical investigation was conducted to find out the effect of neck blast disease on yield-contributing characters, and seed quality traits of aromatic rice in Bangladesh. Both healthy and neck-blast-infected panicles of three aromatic rice cultivars (high-yielding and local) were collected and investigated at Plant Pathology Division, Bangladesh Rice Research Institute (BRRI), Gazipur, Bangladesh. All of the tested varieties were highly susceptible to neck blast disease under natural conditions, though no leaf blast symptoms appear on leaves. Neck blast disease increased grain sterility percentages, reduced grain size, yield and quality traits of seeds. The degrees of yield and seed quality reduction depended on disease severity and variety's genetic make-up. Unfilled grains were the main source of seed-borne pathogen, especially for blast in the seed lot. Transmission of blast pathogen from neck (panicle base) to seed was very poor. These findings are important, especially concerning the seed certification programme in which seed lots are certified on the basis of field inspection. Finally, controlled experiments are needed to draw more critical conclusions. Copyright © 2014 Académie des sciences. Published by Elsevier SAS. All rights reserved.

Preclinical manufacture of anti-HER2 liposome-inserting, scFv-PEG-lipid conjugate. 2. Conjugate micelle identity, purity, stability, and potency analysis.

PubMed

Nellis, David F; Giardina, Steven L; Janini, George M; Shenoy, Shilpa R; Marks, James D; Tsai, Richard; Drummond, Daryl C; Hong, Keelung; Park, John W; Ouellette, Thomas F; Perkins, Shelley C; Kirpotin, Dmitri B

2005-01-01

Analytical methods optimized for micellar F5cys-MP-PEG(2000)-DPSE protein-lipopolymer conjugate are presented. The apparent micelle molecular weight, determined by size exclusion chromatography, ranged from 330 to 960 kDa. The F5cys antibody and conjugate melting points, determined by differential scanning calorimetry, were near 82 degrees C. Traditional methods for characterizing monodisperse protein species were inapplicable to conjugate analysis. The isoelectric point of F5cys (9.2) and the conjugate (8.9) were determined by capillary isoelectric focusing (cIEF) after addition of the zwitterionic detergent CHAPS to the buffer. Conjugate incubation with phospholipase B selectively removed DSPE lipid groups and dispersed the conjugate prior to separation by chromatographic methods. Alternatively, adding 2-propanol (29.4 vol %) and n-butanol (4.5 vol %) to buffers for salt-gradient cation exchange chromatography provided gentler, nonenzymatic dispersion, resulting in well-resolved peaks. This method was used to assess stability, identify contaminants, establish lot-to-lot comparability, and determine the average chromatographic purity (93%) for conjugate lots, described previously. The F5cys amino acid content was confirmed after conjugation. The expected conjugate avidity for immobilized HER-2/neu was measured by bimolecular interaction analysis (BIAcore). Mock therapeutic assemblies were made by conjugate insertion into preformed doxorubicin-encapsulating liposomes for antibody-directed uptake of doxorubicin by HER2-overexpressing cancer cells in vitro. Together these developed assays established that the manufacturing method as described in the first part of this study consistently produced F5cys-MP-PEG(2000)-DSPE having sufficient purity, stability, and functionality for use in preclinical toxicology investigations.

Citywide cluster randomized trial to restore blighted vacant land and its effects on violence, crime, and fear

PubMed Central

Branas, Charles C.; South, Eugenia; Kondo, Michelle C.; Hohl, Bernadette C.; Bourgois, Philippe; Wiebe, Douglas J.; MacDonald, John M.

2018-01-01

Vacant and blighted urban land is a widespread and potentially risky environmental condition encountered by millions of people on a daily basis. About 15% of the land in US cities is deemed vacant or abandoned, an area roughly the size of Switzerland. In a citywide cluster randomized controlled trial, we investigated the effects of standardized, reproducible interventions that restore vacant land on the commission of violence, crime, and the perceptions of fear and safety. Quantitative and ethnographic analyses were included in a mixed-methods approach to more fully test and explicate our findings. A total of 541 randomly sampled vacant lots were randomly assigned into treatment and control study arms; outcomes from police and 445 randomly sampled participants were analyzed over a 38-month study period. Participants living near treated vacant lots reported significantly reduced perceptions of crime (−36.8%, P < 0.05), vandalism (−39.3%, P < 0.05), and safety concerns when going outside their homes (−57.8%, P < 0.05), as well as significantly increased use of outside spaces for relaxing and socializing (75.7%, P < 0.01). Significant reductions in crime overall (−13.3%, P < 0.01), gun violence (−29.1%, P < 0.001), burglary (−21.9%, P < 0.001), and nuisances (−30.3%, P < 0.05) were also found after the treatment of vacant lots in neighborhoods below the poverty line. Blighted and vacant urban land affects people’s perceptions of safety, and their actual, physical safety. Restoration of this land can be an effective and scalable infrastructure intervention for gun violence, crime, and fear in urban neighborhoods. PMID:29483246

Parental perceptions of teen driving: Restrictions, worry and influence.

PubMed

Jewett, Amy; Shults, Ruth A; Bhat, Geeta

2016-12-01

Parents play a critical role in preventing crashes among teens. Research of parental perceptions and concerns regarding teen driving safety is limited. We examined results from the 2013 Summer ConsumerStyles survey that queried parents about restrictions placed on their teen drivers, their perceived level of "worry" about their teen driver's safety, and influence of parental restrictions regarding their teen's driving. We produced frequency distributions for the number of restrictions imposed, parental "worry," and influence of rules regarding their teen's driving, reported by teen's driving license status (learning to drive or obtained a driver's license). Response categories were dichotomized because of small cell sizes, and we ran separate log-linear regression models to explore whether imposing all four restrictions on teen drivers was associated with either worry intensity ("a lot" versus "somewhat, not very much or not at all") or perceived influence of parental rules ("a lot" versus "somewhat, not very much or not at all"). Among the 456 parent respondents, 80% reported having restrictions for their teen driver regarding use of safety belts, drinking and driving, cell phones, and text messaging while driving. However, among the 188 parents of licensed teens, only 9% reported having a written parent-teen driving agreement, either currently or in the past. Worrying "a lot" was reported less frequently by parents of newly licensed teens (36%) compared with parents of learning teens (61%). Parents report having rules and restrictions for their teen drivers, but only a small percentage formalize the rules and restrictions in a written parent-teen driving agreement. Parents worry less about their teen driver's safety during the newly licensed phase, when crash risk is high as compared to the learning phase. Further research is needed into how to effectively support parents in supervising and monitoring their teen driver. Published by Elsevier Ltd.

Airborne endotoxin concentrations at a large open-lot dairy in southern idaho.

PubMed

Dungan, Robert S; Leytem, April B

2009-01-01

Endotoxins are derived from gram-negative bacteria and are a potential respiratory health risk for animals and humans. To determine the potential for endotoxin transport from a large open-lot dairy, total airborne endotoxin concentrations were determined at an upwind location (background) and five downwind locations on three separate days. The downwind locations were situated at of the edge of the lot, 200 and 1390 m downwind from the lot, and downwind from a manure composting area and wastewater holding pond. When the wind was predominantly from the west, the average endotoxin concentration at the upwind location was 24 endotoxin units (EU) m(-3), whereas at the edge of the lot on the downwind side it was 259 EU m(-3). At 200 and 1390 m downwind from the edge of the lot, the average endotoxin concentrations were 168 and 49 EU m(-3), respectively. Average airborne endotoxin concentrations downwind from the composting site (36 EU m(-3)) and wastewater holding pond (89 EU m(-3)) and 1390 m from the edge of the lot were not significantly different from the upwind location. There were no significant correlations between ambient weather data collected and endotoxin concentrations over the experimental period. The downwind data show that the airborne endotoxin concentrations decreased exponentially with distance from the lot edge. Decreasing an individual's proximity to the dairy should lower their risk of airborne endotoxin exposure and associated health effects.

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement

USGS Publications Warehouse

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH8) in the 0.03-m samples above sealed lots (1320 ng m-3) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m-3). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m-3) was five times greater than above unsealed lots (26.0 ng m-3). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m-2 h-1, respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces.

Sampling requirements for forage quality characterization of rectangular hay bales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheaffer, C.C.; Martin, N.P.; Jewett, J.G.

2000-02-01

Commercial lots of alfalfa (Medicago sativa L.) hay are often bought and sold on the basis of forage quality. Proper sampling is essential to obtain accurate forage quality results for pricing of alfalfa hay, but information about sampling is limited to small, 20- to 40-kg rectangular bales. Their objectives were to determine the within-bale variation in 400-kg rectangular bales and to determine the number and distribution of core samples required to represent the crude protein (CP), acid detergent fiber (ADF), neutral detergent fiber (NDF), and dry matter (DM) concentration in commercial lots of alfalfa hay. Four bales were selected frommore » each of three hay lots and core sampled nine times per side for a total of 54 cores per bale. There was no consistent pattern of forage quality variation within bales. Averaged across lots, any portion of a bale was highly correlated with bale grand means for CP, ADF, NDF, and DM. Three lots of hay were probed six times per bale, one core per bale side from 55, 14, and 14 bales per lot. For determination of CP, ADF, NDF, and DM concentration, total core numbers required to achieve an acceptable standard error (SE) were minimized by sampling once per bale. Bootstrap analysis of data from the most variable hay lot suggested that forage quality of any lot of 400-kg alfalfa hay bales should be adequately represented by 12 bales sampled once per bale.« less

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement.

PubMed

Van Metre, Peter C; Majewski, Michael S; Mahler, Barbara J; Foreman, William T; Braun, Christopher L; Wilson, Jennifer T; Burbank, Teresa L

2012-06-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH(8)) in the 0.03-m samples above sealed lots (1320 ng m(-3)) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m(-3)). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m(-3)) was five times greater than above unsealed lots (26.0 ng m(-3)). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m(-2) h(-1), respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces. Published by Elsevier Ltd.

7 CFR 42.121 - Sampling and inspection procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Sampling and inspection procedures. 42.121 Section 42... REGULATIONS STANDARDS FOR CONDITION OF FOOD CONTAINERS Skip Lot Sampling and Inspection Procedures § 42.121 Sampling and inspection procedures. (a) Following skip lot procedure authorization, inspect every lot...

7 CFR 42.121 - Sampling and inspection procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Sampling and inspection procedures. 42.121 Section 42... REGULATIONS STANDARDS FOR CONDITION OF FOOD CONTAINERS Skip Lot Sampling and Inspection Procedures § 42.121 Sampling and inspection procedures. (a) Following skip lot procedure authorization, inspect every lot...

Modelling Carpool and Transit Park-and-Ride Lots

DOT National Transportation Integrated Search

1997-01-01

Park-and-Ride (PnR) lots are an increasingly common element of many areas plans for air quality conformity. However, few, if any, travel models estimate the impacts of carpool PnR lots, and it is not at all clear that they always improve air quality....

7 CFR 993.104 - Lot.

Code of Federal Regulations, 2010 CFR

2010-01-01

... of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... Administrative Rules and Regulations Definitions § 993.104 Lot. (a) Lot for the purposes of §§ 993.49 and 993.149... containers, processed in any continuous production of one calendar day, and offered for inspection as a new...

76 FR 42067 - Inspection and Weighing of Grain in Combined and Single Lots

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-18

.... * * * * * (b) * * * (1) General. If grain in a carrier is offered for inspection or weighing service as one lot... weighing service procedures that GIPSA's Federal Grain Inspection Service (FGIS) performs under the... the inspection and weighing of such container lots to the official service provider's area of...

9 CFR 351.19 - Refusal of certification for specific lots.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Remedies... lot of technical animal fat is ineligible for certification under § 351.3, or any materials to be used in a lot of technical animal fat would make the technical animal fat ineligible for such...

9 CFR 351.19 - Refusal of certification for specific lots.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Remedies... lot of technical animal fat is ineligible for certification under § 351.3, or any materials to be used in a lot of technical animal fat would make the technical animal fat ineligible for such...

9 CFR 351.19 - Refusal of certification for specific lots.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Remedies... lot of technical animal fat is ineligible for certification under § 351.3, or any materials to be used in a lot of technical animal fat would make the technical animal fat ineligible for such...

9 CFR 351.19 - Refusal of certification for specific lots.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Remedies... lot of technical animal fat is ineligible for certification under § 351.3, or any materials to be used in a lot of technical animal fat would make the technical animal fat ineligible for such...

46 CFR 160.026-6 - Sampling, inspection, and tests of production lots.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Bacteriological limits and salt content MIL-W-15117 and U.S. Public Health “Drinking Water Standards.” (e) Lot..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Water, Emergency Drinking (In... lots. (a) General. Containers of emergency drinking water must be tested in accordance with the...

46 CFR 160.026-6 - Sampling, inspection, and tests of production lots.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Bacteriological limits and salt content MIL-W-15117 and U.S. Public Health “Drinking Water Standards.” (e) Lot..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Water, Emergency Drinking (In... lots. (a) General. Containers of emergency drinking water must be tested in accordance with the...

46 CFR 160.026-6 - Sampling, inspection, and tests of production lots.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Bacteriological limits and salt content MIL-W-15117 and U.S. Public Health “Drinking Water Standards.” (e) Lot..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Water, Emergency Drinking (In... lots. (a) General. Containers of emergency drinking water must be tested in accordance with the...

46 CFR 160.026-6 - Sampling, inspection, and tests of production lots.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Bacteriological limits and salt content MIL-W-15117 and U.S. Public Health “Drinking Water Standards.” (e) Lot..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Water, Emergency Drinking (In... lots. (a) General. Containers of emergency drinking water must be tested in accordance with the...

46 CFR 160.026-6 - Sampling, inspection, and tests of production lots.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Bacteriological limits and salt content MIL-W-15117 and U.S. Public Health “Drinking Water Standards.” (e) Lot..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Water, Emergency Drinking (In... lots. (a) General. Containers of emergency drinking water must be tested in accordance with the...

Fingerprint test data report: FM 5834 test lots No. 1, 3, 4, and 5. [resin matrix composites

NASA Technical Reports Server (NTRS)

1986-01-01

Quality control testing is presented for various lots of resin matrix composites. The tests conducted were filler test, resin test, fabric test, and prepreg test for lots 1, 3, 4, and 5. The results of the tests are presented in chart forms.

Synchronizable Series Expressions. Part 2. Overview of the Theory and Implementation.

DTIC Science & Technology

1987-11-01

more running time than shown in the table. because time is eventually required in order to collect the garbage it creates. Program Running ’rime Garbage...possible to simply put an enumerator where it is used.) (loop for x integer from I to 4 collect x) - (lotS* ((x (Eup I :to 4))) (declare (type integer x...below. (loop for x from 1 to 4 and for y = 0 then (1- x) collect (list x y)) - (lotS* ((x (Eup 1 :to 4)) (y (Tprevious (1- x) 0))) (Rlist (list x y

Methyl Centralite Coated M10 Propellant for the 25-mm Bushmaster Gun Projectiles

DTIC Science & Technology

1984-09-01

orisinator. servces y th U.S. Gvernent 4di I:THE INFORMATION CONTAINED HEREIN SMALL BE USED FOR GOVERNMENT PURPOSES ONLY ______Unclassified SECURITY CLASS...bomb DpiDt versus P t-aces of Lots 42 RAD-PE-559-15 compared with lots RAD-PE-S59-ll, 16, and 17 and Swiss lot P-2078. 1! ] y .,,narison of Lot RAD-PE...further remove ether and improve coating gradient , 28 to 48 hour water dry time to remove practically all of the coating acquired alcohol, and a

Coal-Tar-Based Parking Lot Sealcoat: An Unrecognized Source of PAH to Settled House Dust

PubMed Central

2010-01-01

Despite much speculation, the principal factors controlling concentrations of polycyclic aromatic hydrocarbons (PAH) in settled house dust (SHD) have not yet been identified. In response to recent reports that dust from pavement with coal-tar-based sealcoat contains extremely high concentrations of PAH, we measured PAH in SHD from 23 apartments and in dust from their associated parking lots, one-half of which had coal-tar-based sealcoat (CT). The median concentration of total PAH (T-PAH) in dust from CT parking lots (4760 μg/g, n = 11) was 530 times higher than that from parking lots with other pavement surface types (asphalt-based sealcoat, unsealed asphalt, concrete [median 9.0 μg/g, n = 12]). T-PAH in SHD from apartments with CT parking lots (median 129 μg/g) was 25 times higher than that in SHD from apartments with parking lots with other pavement surface types (median 5.1 μg/g). Presence or absence of CT on a parking lot explained 48% of the variance in log-transformed T-PAH in SHD. Urban land-use intensity near the residence also had a significant but weaker relation to T-PAH. No other variables tested, including carpeting, frequency of vacuuming, and indoor burning, were significant. PMID:20063893

A photographic method for estimating wear of coal tar sealcoat from parking lots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mateo Scoggins; Tom Ennis; Nathan Parker

2009-07-01

Coal-tar-based sealcoat has been recognized as an important source of PAHs to the environment through wear and transport via stormwater runoff. Sealcoat removal rates have not been measured or even estimated in the literature due to the complex array of physical and chemical process involved. A photographic study was conducted that incorporates all sources of wear using 10 coal tar-sealed parking lots in Austin, Texas, with sealcoat age ranging from 0 to 5 years. Randomly located photographs from each parking lot were analyzed digitally to quantify black sealed areas versus lighter colored unsealed areas at the pixel level. The resultsmore » indicate that coal tar sealcoat wears off of the driving areas of parking lots at a rate of approximately 4.7% per year, and from the parking areas of the lots at a rate of approximately 1.4% per year. The overall annual loss of sealcoat was calculated at 2.4%. This results in an annual delivery to the environment of 0.51 g of PAHs per m{sup 2} of coal tar-sealed parking lot. These values provide a more robust and much higher estimate of loading of PAHs from coal tar sealcoated parking lots when compared to other available measures. 20 refs., 6 figs.« less

Exploring lot-to-lot variation in spoilage bacterial communities on commercial modified atmosphere packaged beef.

PubMed

Säde, Elina; Penttinen, Katri; Björkroth, Johanna; Hultman, Jenni

2017-04-01

Understanding the factors influencing meat bacterial communities is important as these communities are largely responsible for meat spoilage. The composition and structure of a bacterial community on a high-O 2 modified-atmosphere packaged beef product were examined after packaging, on the use-by date and two days after, to determine whether the communities at each stage were similar to those in samples taken from different production lots. Furthermore, we examined whether the taxa associated with product spoilage were distributed across production lots. Results from 16S rRNA amplicon sequencing showed that while the early samples harbored distinct bacterial communities, after 8-12 days storage at 6 °C the communities were similar to those in samples from different lots, comprising mainly of common meat spoilage bacteria Carnobacterium spp., Brochothrix spp., Leuconostoc spp. and Lactococcus spp. Interestingly, abundant operational taxonomic units associated with product spoilage were shared between the production lots, suggesting that the bacteria enable to spoil the product were constant contaminants in the production chain. A characteristic succession pattern and the distribution of common spoilage bacteria between lots suggest that both the packaging type and the initial community structure influenced the development of the spoilage bacterial community. Copyright © 2016 Elsevier Ltd. All rights reserved.

"Thinking a Lot" Among the Khwe of South Africa: A Key Idiom of Personal and Interpersonal Distress.

PubMed

den Hertog, T N; de Jong, M; van der Ham, A J; Hinton, D; Reis, R

2016-09-01

"Thinking too much", and variations such as "thinking a lot", are common idioms of distress across the world. The contextual meaning of this idiom of distress in particular localities remains largely unknown. This paper reports on a systematic study of the content and cause, consequences, and social response and coping related to the local terms |x'an n|a te and |eu-ca n|a te, both translated as "thinking a lot", and was part of a larger ethnographic study among the Khwe of South Africa. Semi-structured exploratory interviews with community members revealed that "thinking a lot" refers to a common experience of reflecting on personal and interpersonal problems. Consequences were described in emotional, psychological, social, behavioral, and physical effects. Coping strategies included social support, distraction, and religious practices. Our contextualized approach revealed meanings and experiences of "thinking a lot" that go beyond a psychological state or psychopathology. The common experience of "thinking a lot" is situated in socio-political, economic, and social context that reflect the marginalized and displaced position of the Khwe. We argue that "thinking a lot" and associated local meanings may vary across settings, may not necessarily indicate psychopathology, and should be understood in individual, interpersonal, community, and socio-political dimensions.

Vacant Lots: Productive Sites for Aedes (Stegomyia) aegypti (Diptera: Culicidae) in Mérida City, México

PubMed Central

BAAK-BAAK, CARLOS M.; ARANA-GUARDIA, ROGER; CIGARROA-TOLEDO, NOHEMI; LOROÑO-PINO, MARÍA ALBA; REYES-SOLIS, GUADALUPE; MACHAIN-WILLIAMS, CARLOS; BEATY, BARRY J.; EISEN, LARS; GARCÍA-REJÓN, JULIÁN E.

2014-01-01

We assessed the potential for vacant lots and other non-residential settings to serve as source environments for Aedes (Stegomyia) aegypti (L.) in Mérida City, México. Mosquito immatures were collected, during November 2011 – June 2013, from residential premises (n = 156 site visits) and non-residential settings represented by vacant lots (50), parking lots (18), and streets/sidewalks (28). Collections totaled 46,025 mosquito immatures of 13 species. Ae. aegypti was the most commonly encountered species accounting for 81.0% of total immatures, followed by Culex quinquefasciatus Say (12.1%). Site visits to vacant lots (74.0%) were more likely to result in collection of Ae. aegypti immatures that residential premises (35.9%). Tires accounted for 75.5% of Ae. aegypti immatures collected from vacant lots. Our data suggest that vacant lots should be considered for inclusion in mosquito surveillance and control efforts in Mérida City, as they often are located near homes, commonly have abundant vegetation, and frequently harbor accumulations of small and large discarded water-holding containers that we now have demonstrated to serve as development sites for immature mosquitoes. Additionally, we present data for associations of immature production with various container characteristics, such as storage capacity, water quality and physical location in the environment. PMID:24724299

Coal-tar-based parking lot sealcoat: An unrecognized source of PAH to settled house dust

USGS Publications Warehouse

Mahler, B.J.; Van Metre, P.C.; Wilson, J.T.; Musgrove, M.; Burbank, T.L.; Ennis, T.E.; Bashara, T.J.

2010-01-01

Despite much speculation, the principal factors controlling concentrations of polycyclic aromatic hydrocarbons (PAH) in settled house dust (SHD) have not yet been identified. In response to recent reports that dust from pavement with coaltar-based sealcoat contains extremely high concentrations of PAH, we measured PAH in SHD from 23 apartments and in dust from their associated parking lots, one-half of which had coal-tar-based sealcoat (CT). The median concentration of total PAH (T-PAH) in dust from CT parking lots (4760 ??g/g, n = 11) was 530 times higher than that from parking lots with other pavement surface types (asphalt-based sealcoat, unsealed asphalt, concrete [median 9.0 ??g/g, n = 12]). T-PAH in SHD from apartments with CT parking lots (median 129 ??g/g) was 25 times higher than that in SHD from apartments with parking lots with other pavement surface types (median 5.1 ??g/g). Presence or absence of CT on a parking lot explained 48% of the variance in log-transformed T-PAH in SHD. Urban land-use intensity near the residence also had a significant but weaker relation to T-PAH. No other variables tested, including carpeting, frequency of vacuuming, and indoor burning, were significant. ?? 2010 American Chemical Society.

Direct reconstruction of pharmacokinetic parameters in dynamic fluorescence molecular tomography by the augmented Lagrangian method

NASA Astrophysics Data System (ADS)

Zhu, Dianwen; Zhang, Wei; Zhao, Yue; Li, Changqing

2016-03-01

Dynamic fluorescence molecular tomography (FMT) has the potential to quantify physiological or biochemical information, known as pharmacokinetic parameters, which are important for cancer detection, drug development and delivery etc. To image those parameters, there are indirect methods, which are easier to implement but tend to provide images with low signal-to-noise ratio, and direct methods, which model all the measurement noises together and are statistically more efficient. The direct reconstruction methods in dynamic FMT have attracted a lot of attention recently. However, the coupling of tomographic image reconstruction and nonlinearity of kinetic parameter estimation due to the compartment modeling has imposed a huge computational burden to the direct reconstruction of the kinetic parameters. In this paper, we propose to take advantage of both the direct and indirect reconstruction ideas through a variable splitting strategy under the augmented Lagrangian framework. Each iteration of the direct reconstruction is split into two steps: the dynamic FMT image reconstruction and the node-wise nonlinear least squares fitting of the pharmacokinetic parameter images. Through numerical simulation studies, we have found that the proposed algorithm can achieve good reconstruction results within a small amount of time. This will be the first step for a combined dynamic PET and FMT imaging in the future.

The study of the mission instruments of GOSAT-2

NASA Astrophysics Data System (ADS)

Suto, H.; Nakajima, M.; Kuze, A.; Shiomi, K.; Shimoda, H.

2012-12-01

Greenhouse Gases Observing Satellite "GOSAT" was launched in January of 2009 and have observed the carbon dioxide and the methane almost four years. Additionally, the Level 1B algorithm has been improved based on the on board calibration and ground test using Engineering model and the accuracy of the level 1B data, that is the spectrum, has been improved. This has led to the more accurate calculation of the concentration of carbon dioxide and methane with small bias. At the same time, some issues have become clearer little by little through the on orbit operation. Especially a lot of data have been affected by the cloud, so few data have been used until now. However, the satellite has come to be recognized as an effective means of the detection of the global distribution of the greenhouse gases concentration. And in addition to the effort to resolve the issues which have become clear until now, the improvement of the observation performance have been required by a lot of users. Therefore, we researched the concrete requirements of users and set the mission requirements for GOSAT-2. Based on this mission requirement, we have studied the possibilities of these requirements. This study was implemented as premises for the usage of the Fourier Transform Spectrometer to detect the greenhouse gases as well as GOSAT. We considered the methods to increase the number of the useful data. For example, the reduction of the footprints size, increase of the number of the IFOV, the intelligent pointing and so on. It's necessary to maintain the Signal to Noise ration of the GOSAT. In addition to the method to increase the number of the useful data, we have researched the size of the aperture of the optics to maintain the signal to noise ratio corresponding to the reduction of the footprint seize. But the possibility of the corner cube used in the Fourier transform spectrometer limits the aperture size. We decided the aperture size (and corner cube size) based on the trade-off among corner cube size, footprint size and signal to noise ratio and the opinions of the scientists. In addition to the improvements of the performaces, the following requirements has been presented. To evaluate the relative matters of the anthropogenic emissions, to contribute to the MRV of REDD+ and so on. In order to meet these requirements the Fourier Transform Spectrometer on GOSAT-2 will has the additional observation channel for the carbon monoxide and Imager will has the spectrometer using the grating for Nitorgen Dioxide. Now we are investigating the possibilities of these additional functions and increase of the performances and we will decide the specifications of GOSAT-2 within one year.

Source Authentication for Code Dissemination Supporting Dynamic Packet Size in Wireless Sensor Networks.

PubMed

Kim, Daehee; Kim, Dongwan; An, Sunshin

2016-07-09

Code dissemination in wireless sensor networks (WSNs) is a procedure for distributing a new code image over the air in order to update programs. Due to the fact that WSNs are mostly deployed in unattended and hostile environments, secure code dissemination ensuring authenticity and integrity is essential. Recent works on dynamic packet size control in WSNs allow enhancing the energy efficiency of code dissemination by dynamically changing the packet size on the basis of link quality. However, the authentication tokens attached by the base station become useless in the next hop where the packet size can vary according to the link quality of the next hop. In this paper, we propose three source authentication schemes for code dissemination supporting dynamic packet size. Compared to traditional source authentication schemes such as μTESLA and digital signatures, our schemes provide secure source authentication under the environment, where the packet size changes in each hop, with smaller energy consumption.

Source Authentication for Code Dissemination Supporting Dynamic Packet Size in Wireless Sensor Networks †

PubMed Central

Kim, Daehee; Kim, Dongwan; An, Sunshin

2016-01-01

Code dissemination in wireless sensor networks (WSNs) is a procedure for distributing a new code image over the air in order to update programs. Due to the fact that WSNs are mostly deployed in unattended and hostile environments, secure code dissemination ensuring authenticity and integrity is essential. Recent works on dynamic packet size control in WSNs allow enhancing the energy efficiency of code dissemination by dynamically changing the packet size on the basis of link quality. However, the authentication tokens attached by the base station become useless in the next hop where the packet size can vary according to the link quality of the next hop. In this paper, we propose three source authentication schemes for code dissemination supporting dynamic packet size. Compared to traditional source authentication schemes such as μTESLA and digital signatures, our schemes provide secure source authentication under the environment, where the packet size changes in each hop, with smaller energy consumption. PMID:27409616

The influence of low temperatures on dynamic mechanical properties of animal bone

NASA Astrophysics Data System (ADS)

Mardas, Marcin; Kubisz, Leszek; Mielcarek, Slawomir; Biskupski, Piotr

2009-01-01

Different preservation methods are currently used in bone banks, even though their effects on allograft quality are not fully understood. Freezing is one of the most popular methods of preservation in tissue banking. Yet, there is not a lot of data on dynamic mechanical properties of frozen bone. Material used in this study was femoral bones from adult bovine that were machine cut and frozen to the temperature 140°C. Both elastic modulus and loss modulus were measured at 1, 3, 5, 10, and 20 Hz in the temperature range of 30-200°C. Differences between frozen and control samples were observed. The frequency increase always led to the increase in elastic modulus values and decrease in loss modulus values. Freezing reduced the elastic modulus values of about 25% and the loss modulus values of about 45% when measured at 20°C.

Taking chances and making mistakes: non-genetic phenotypic heterogeneity and its consequences for surviving in dynamic environments

PubMed Central

van Boxtel, Coco; van Heerden, Johan H.; Nordholt, Niclas; Schmidt, Phillipp

2017-01-01

Natural selection has shaped the strategies for survival and growth of microorganisms. The success of microorganisms depends not only on slow evolutionary tuning but also on the ability to adapt to unpredictable changes in their environment. In principle, adaptive strategies range from purely deterministic mechanisms to those that exploit the randomness intrinsic to many cellular and molecular processes. Depending on the environment and selective pressures, particular strategies can lie somewhere along this continuum. In recent years, non-genetic cell-to-cell differences have received a lot of attention, not least because of their potential impact on the ability of microbial populations to survive in dynamic environments. Using several examples, we describe the origins of spontaneous and induced mechanisms of phenotypic adaptation. We identify some of the commonalities of these examples and consider the potential role of chance and constraints in microbial phenotypic adaptation. PMID:28701503

Special functions of valve organs of blood-sucking female mosquitoes

NASA Astrophysics Data System (ADS)

Kim, Boheum; Lee, Sangjoon

2010-11-01

Food-feeding insects usually have valve organs to regulate the sucking flow effectively. Female mosquitoes sucking lots of blood instantaneously have a unique valve system between two pumping organs located in their head. The valve system seems to prevent reverse flow and to grind granule particles such as red blood cells. To understand the functional characteristics of this valve organ in detail, the volumetric flow rate passing through the valves and their interaction with the two-pumps need to be investigated. However, it is very difficult to observe the dynamic behaviors of pumping organs and valve system. In this study, the dynamic motions of valve organs of blood-sucking female mosquitoes were observed under in vivo condition using synchrotron X-ray micro imaging technique. X-ray micro computed tomography was also employed to examine the three-dimensional internal structure of the blood pumping system including valve organs.

Modelling voltage sag mitigation using dynamic voltage restorer and analyzing power quality issue

NASA Astrophysics Data System (ADS)

Ismail, Nor Laili; Hidzir, Hizrin Dayana Mohd; Thanakodi, Suresh; Nazar, Nazatul Shiema Moh; Ibrahim, Pungut; Ali, Che Ku Muhammad Sabri Che Ku

2018-02-01

Power quality problem which are arise due to a fault or a pulsed load can have caused an interruption of critical load. The modern power systems are becoming more sensitive to the quality of the power supplied by the utility company. Voltage sags and swells, flicker, interruptions, harmonic distortion and other distortion to the sinusoidal waveform are the examples of the power quality problems. The most affected due to these problems is industrial customers who use a lot of sensitive equipment. There has suffered a huge loss to these problems. Resulting of broken or damage equipment if voltage sag exceeds the sensitive threshold of the equipment. Thus, device such as Static Synchronous Compensator (STATCOM) and Dynamic Voltage Restorer (DVR) has been created to solve this problem among users. DVR is a custom power device that most effective and efficient. This paper intended to report the DVR operations during voltage sag compensation.

The corrosion fatigue fractography of Ti-24Al-11Nb

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Y.; Wang, Y.B.; Chu, W.Y.

1994-03-01

Many researchers have studied the fracture behaviors and fractography of the Ti-24Al-11Nb alloy. While hydrogen induced delayed fracture could occur in this titanium aluminide in hydrogen gas at temperatures above 300[degree]C, there was no obvious difference in fractography of the alloy in hydrogen or air. The fractography of stress corrosion cracking in a solution was also similar to that of overloaded fracture in air. The recent work showed that hydrogen induced delayed fracture for a notched sample could occur during dynamic cathodic charging at the temperature. There were a lot of small dimples on the fracture surface near the notchmore » tip when K[sub I] neared the threshold k[sub IH]. This differed from that of an overloaded fracture. The fractography of corrosion fatigue in methanol or during dynamic charging for the Ti-24Al-11Nb alloy was studied in this paper.« less

Analytic study of a rolling sphere on a rough surface

NASA Astrophysics Data System (ADS)

Florea, Olivia A.; Rosca, Ileana C.

2016-11-01

In this paper it is realized an analytic study of the rolling's sphere on a rough horizontal plane under the action of its own gravity. The necessities of integration of the system of dynamical equations of motion lead us to find a reference system where the motion equations should be transformed into simpler expressions and which, in the presence of some significant hypothesis to permit the application of some original methods of analytical integration. In technical applications, the bodies may have a free rolling motion or a motion constrained by geometrical relations in assemblies of parts and machine parts. This study involves a lot of investigations in the field of tribology and of applied dynamics accompanied by experiments. Multiple recordings of several trajectories of the sphere, as well as their treatment of images, also followed by statistical processing experimental data allowed highlighting a very good agreement between the theoretical findings and experimental results.

Using STELLA System Dynamic Model to Analyze Greenhouse Gases' Emission From Solid Waste Management in Taiwan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horng, Jao-Jia; Lee, R.F.; Liao, K.Y.

2004-03-31

Using a system dynamic model (SDM), such as STELLA, to analyze the waste management policy is a new trial for Taiwan's research communities. We have developed an easy and relatively accurate model for analyzing the greenhouse gases emission for the wastes from animal farming and municipalities. With the local research data of the past decade, we extract the most prominent factors and assemble the SDM. The results and scenarios were compared with the national inventory. By comparing to the past data, we found these models reasonably represent the situation in Taiwan. However, SDM can program many scenarios and produce amore » lot of prediction data. With the development of many program control tools on STELLA, we believe the models could be further used by researchers or policy-makers to find the needed research topics, to set the future scenarios and to determine the management tools.« less

Measurement of Size-dependent Dynamic Shape Factors of Quartz Particles in Two Flow Regimes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexander, Jennifer M.; Bell, David M.; Imre, D.

2016-08-02

Understanding and modeling the behavior of quartz dust particles, commonly found in the atmosphere, requires knowledge of many relevant particles properties, including particle shape. This study uses a single particle mass spectrometer, a differential mobility analyzer, and an aerosol particle mass analyzer to measure quartz aerosol particles mobility, aerodynamic, and volume equivalent diameters, mass, composition, effective density, and dynamic shape factor as a function of particle size, in both the free molecular and transition flow regimes. The results clearly demonstrate that dynamic shape factors can vary significantly as a function of particle size. For the quartz samples studied here, themore » dynamic shape factors increase with size, indicating that larger particles are significantly more aspherical than smaller particles. In addition, dynamic shape factors measured in the free-molecular (χv) and transition (χt) flow regimes can be significantly different, and these differences vary with the size of the quartz particles. For quartz, χv of small (d < 200 nm) particles is 1.25, while χv of larger particles (d ~ 440 nm) is 1.6, with a continuously increasing trend with particle size. In contrast χt, of small particles starts at 1.1 increasing slowly to 1.34 for 550 nm diameter particles. The multidimensional particle characterization approach used here goes beyond determination of average properties for each size, to provide additional information about how the particle dynamic shape factor may vary even for particles with the same mass and volume equivalent diameter.« less

Study the fragment size distribution in dynamic fragmentation of laser shock loding tin

NASA Astrophysics Data System (ADS)

He, Weihua; Xin, Jianting; Chu, Genbai; Shui, Min; Xi, Tao; Zhao, Yongqiang; Gu, Yuqiu

2017-06-01

Characterizing the distribution of fragment size produced from dynamic fragmentation process is very important for fundamental science like predicting material dymanic response performance and for a variety of engineering applications. However, only a few data about fragment mass or size have been obtained due to its great challenge in its dynamic measurement. This paper would focus on investigating the fragment size distribution from the dynamic fragmentation of laser shock-loaded metal. Material ejection of tin sample with wedge shape groove in the free surface is collected with soft recovery technique. Via fine post-shot analysis techniques including X-ray micro-tomography and the improved watershed method, it is found that fragments can be well detected. To characterize their size distributions, a random geometric statistics method based on Poisson mixtures was derived for dynamic heterogeneous fragmentation problem, which leads to a linear combinational exponential distribution. Finally we examined the size distribution of laser shock-loaded tin with the derived model, and provided comparisons with other state-of-art models. The resulting comparisons prove that our proposed model can provide more reasonable fitting result for laser shock-loaded metal.

Temperature-driven regime shifts in the dynamics of size-structured populations.

PubMed

Ohlberger, Jan; Edeline, Eric; Vøllestad, Leif Asbjørn; Stenseth, Nils C; Claessen, David

2011-02-01

Global warming impacts virtually all biota and ecosystems. Many of these impacts are mediated through direct effects of temperature on individual vital rates. Yet how this translates from the individual to the population level is still poorly understood, hampering the assessment of global warming impacts on population structure and dynamics. Here, we study the effects of temperature on intraspecific competition and cannibalism and the population dynamical consequences in a size-structured fish population. We use a physiologically structured consumer-resource model in which we explicitly model the temperature dependencies of the consumer vital rates and the resource population growth rate. Our model predicts that increased temperature decreases resource density despite higher resource growth rates, reflecting stronger intraspecific competition among consumers. At a critical temperature, the consumer population dynamics destabilize and shift from a stable equilibrium to competition-driven generation cycles that are dominated by recruits. As a consequence, maximum age decreases and the proportion of younger and smaller-sized fish increases. These model predictions support the hypothesis of decreasing mean body sizes due to increased temperatures. We conclude that in size-structured fish populations, global warming may increase competition, favor smaller size classes, and induce regime shifts that destabilize population and community dynamics.

Classification of Magnetic Nanoparticle Systems—Synthesis, Standardization and Analysis Methods in the NanoMag Project

PubMed Central

Bogren, Sara; Fornara, Andrea; Ludwig, Frank; del Puerto Morales, Maria; Steinhoff, Uwe; Fougt Hansen, Mikkel; Kazakova, Olga; Johansson, Christer

2015-01-01

This study presents classification of different magnetic single- and multi-core particle systems using their measured dynamic magnetic properties together with their nanocrystal and particle sizes. The dynamic magnetic properties are measured with AC (dynamical) susceptometry and magnetorelaxometry and the size parameters are determined from electron microscopy and dynamic light scattering. Using these methods, we also show that the nanocrystal size and particle morphology determines the dynamic magnetic properties for both single- and multi-core particles. The presented results are obtained from the four year EU NMP FP7 project, NanoMag, which is focused on standardization of analysis methods for magnetic nanoparticles. PMID:26343639

Cooperative storage of shared files in a parallel computing system with dynamic block size

DOEpatents

Bent, John M.; Faibish, Sorin; Grider, Gary

2015-11-10

Improved techniques are provided for parallel writing of data to a shared object in a parallel computing system. A method is provided for storing data generated by a plurality of parallel processes to a shared object in a parallel computing system. The method is performed by at least one of the processes and comprises: dynamically determining a block size for storing the data; exchanging a determined amount of the data with at least one additional process to achieve a block of the data having the dynamically determined block size; and writing the block of the data having the dynamically determined block size to a file system. The determined block size comprises, e.g., a total amount of the data to be stored divided by the number of parallel processes. The file system comprises, for example, a log structured virtual parallel file system, such as a Parallel Log-Structured File System (PLFS).

Dynamics and Predictability of The Eta Regional Model: The Role of Domain Size

NASA Astrophysics Data System (ADS)

Vannitsem, S.; Chomé, F.; Nicolis, C.

This paper investigates the dynamical properties of the Eta model, a state-of-the- art nested limited-area model, following the approach previously developed by the present authors. It is first shown that the intrinsic dynamics of the model depends crucially on the size of the domain, with a non-chaotic behavior for small domains, supporting earlier findings on the absence of sensitivity to the initial conditions in these models. The quality of the predictions of several Eta model versions differing by their domain size is next evaluated and compared with the Avn analyses on a targeted region, centered on France. Contrary to what is usually taken for granted, a non-trivial relation between predictability and domain size is found, the best model versions be- ing the ones integrated on the smallest and the largest domain sizes. An explanation in connection with the intrinsic dynamics of the model is advanced.

Simulation of Particle Size Effect on Dynamic Properties and Fracture of PTFE-W-Al Composites

NASA Astrophysics Data System (ADS)

Herbold, Eric; Cai, Jing; Benson, David; Nesterenko, Vitali

2007-06-01

Recent investigations of the dynamic compressive strength of cold isostatically pressed (CIP) composites of polytetrafluoroethylene (PTFE), tungsten and aluminum powders show significant differences depending on the size of metallic particles. PTFE and aluminum mixtures are known to be energetic under dynamic and thermal loading. The addition of tungsten increases density and overall strength of the sample. Multi-material Eulerian and arbitrary Lagrangian-Eulerian methods were used for the investigation due to the complexity of the microstructure, relatively large deformations and the ability to handle the formation of free surfaces in a natural manner. The calculations indicate that the observed dependence of sample strength on particle size is due to the formation of force chains under dynamic loading in samples with small particle sizes even at larger porosity in comparison with samples with large grain size and larger density.

Ammonia losses and nitrogen partitioning at a southern High Plains open lot dairy

NASA Astrophysics Data System (ADS)

Todd, Richard W.; Cole, N. Andy; Hagevoort, G. Robert; Casey, Kenneth D.; Auvermann, Brent W.

2015-06-01

Animal agriculture is a significant source of ammonia (NH3). Cattle excrete most ingested nitrogen (N); most urinary N is converted to NH3, volatilized and lost to the atmosphere. Open lot dairies on the southern High Plains are a growing industry and face environmental challenges as well as reporting requirements for NH3 emissions. We quantified NH3 emissions from the open lot and wastewater lagoons of a commercial New Mexico dairy during a nine-day summer campaign. The 3500-cow dairy consisted of open lot, manure-surfaced corrals (22.5 ha area). Lactating cows comprised 80% of the herd. A flush system using recycled wastewater intermittently removed manure from feeding alleys to three lagoons (1.8 ha area). Open path lasers measured atmospheric NH3 concentration, sonic anemometers characterized turbulence, and inverse dispersion analysis was used to quantify emissions. Ammonia fluxes (15-min) averaged 56 and 37 μg m-2 s-1 at the open lot and lagoons, respectively. Ammonia emission rate averaged 1061 kg d-1 at the open lot and 59 kg d-1 at the lagoons; 95% of NH3 was emitted from the open lot. The per capita emission rate of NH3 was 304 g cow-1 d-1 from the open lot (41% of N intake) and 17 g cow-1 d-1 from lagoons (2% of N intake). Daily N input at the dairy was 2139 kg d-1, with 43, 36, 19 and 2% of the N partitioned to NH3 emission, manure/lagoons, milk, and cows, respectively.

Separating parental environment from seed size effects on next generation growth and development in Arabidopsis.

PubMed

Elwell, Angela L; Gronwall, David S; Miller, Nathan D; Spalding, Edgar P; Brooks, Tessa L Durham

2011-02-01

Plant growth and development is profoundly influenced by environmental conditions that laboratory experimentation typically attempts to control. However, growth conditions are not uniform between or even within laboratories and the extent to which these differences influence plant growth and development is unknown. Experiments with wild-type Arabidopsis thaliana were designed to quantify the influences of parental environment and seed size on growth and development in the next generation. A single lot of seed was planted in six environmental chambers and grown to maturity. The seed produced was mechanically sieved into small and large size classes then grown in a common environment and subjected to a set of assays spanning the life cycle. Analysis of variance demonstrated that seed size effects were particularly significant early in development, affecting primary root growth and gravitropism, but also flowering time. Parental environment affected progeny germination time, flowering and weight of seed the progeny produced. In some cases, the parental environment affected the magnitude of (interacted with) the observed seed size effects. These data indicate that life history circumstances of the parental generation can affect growth and development throughout the life cycle of the next generation to an extent that should be considered when performing genetic studies. © 2010 Blackwell Publishing Ltd.

Structure of the microclimate at a woodland/parking-lot interface

Treesearch

David R. Miller

1977-01-01

Radiation balances and vertical and horizontal profiles of air temperature, vapor pressure and wind speed were measured across the interface of a large asphalt parking lot and an 18-m-tall Quercus velutina forest. The partitioning of available energy over the adjacent areas shows steep gradients between the parking lot and forest microclimates....

78 FR 57033 - United States Standards for Condition of Food Containers

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-17

... containers during production. Stationary lot sampling is the process of randomly selecting sample units from.... * * * * * Stationary lot sampling. The process of randomly selecting sample units from a lot whose production has been... less than \\1/16\\-inch Stringy seal (excessive plastic threads showing at edge of seal 222 area...

A new tool for estimating phosphorus loss from cattle barnyards and outdoor lots

USDA-ARS?s Scientific Manuscript database

Phosphorus (P) loss from agriculture can compromise quality of receiving water bodies. For cattle farms, P can be lost from cropland, pastures, and outdoor animal lots. We developed a new model that predicts annual runoff, total solids loss, and total and dissolved P loss from cattle lots. The model...

7 CFR 868.36 - Loss of identity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Loss of identity. 868.36 Section 868.36 Agriculture... identity. (a) Lots. The identity of a packaged lot, bulk lot, or sublot of a commodity shall be considered... or location after the time of original inspection, unless the identity is preserved; or (2) More...

Nutrient concentrations in leachate and runoff from dairy cattle lots with different surface materials

USDA-ARS?s Scientific Manuscript database

Nitrogen (N) and phosphorus (P) loss from agriculture persists as a water quality issue, and outdoor cattle lots can have a high loss potential. We monitored hydrology and nutrient concentrations in leachate and runoff from dairy heifer lots constructed with three surface materials (soil, sand, bark...

7 CFR 868.36 - Loss of identity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 7 2014-01-01 2014-01-01 false Loss of identity. 868.36 Section 868.36 Agriculture... identity. (a) Lots. The identity of a packaged lot, bulk lot, or sublot of a commodity shall be considered... or location after the time of original inspection, unless the identity is preserved; or (2) More...

7 CFR 868.36 - Loss of identity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 7 2011-01-01 2011-01-01 false Loss of identity. 868.36 Section 868.36 Agriculture... identity. (a) Lots. The identity of a packaged lot, bulk lot, or sublot of a commodity shall be considered... or location after the time of original inspection, unless the identity is preserved; or (2) More...

7 CFR 868.36 - Loss of identity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 7 2013-01-01 2013-01-01 false Loss of identity. 868.36 Section 868.36 Agriculture... identity. (a) Lots. The identity of a packaged lot, bulk lot, or sublot of a commodity shall be considered... or location after the time of original inspection, unless the identity is preserved; or (2) More...

7 CFR 868.36 - Loss of identity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 7 2012-01-01 2012-01-01 false Loss of identity. 868.36 Section 868.36 Agriculture... identity. (a) Lots. The identity of a packaged lot, bulk lot, or sublot of a commodity shall be considered... or location after the time of original inspection, unless the identity is preserved; or (2) More...

Residential demolition and its impact on vacant lot hydrology: implications for the management of stormwater and sewer system overflows

EPA Science Inventory

Increased residential demolitions have made vacant lots a ubiquitous feature of the contemporary urban landscape. Vacant lots may provide ecosystem services such as stormwater runoff capture, but the extent of these functions will be regulated by soil hydrology. We evaluated soil...

Three Permeable Pavements Performances for Priority Metal Pollutants and Metals Associated with Deicing Chemicals from Edison Parking Lot, NJ

EPA Science Inventory

The U.S. Environmental Protection Agency constructed a 4000-m2 parking lot in Edison, New Jersey in 2009. The parking lot is surfaced with three permeable pavements [permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA)]. Samples of each p...

7 CFR 800.85 - Inspection of grain in combined lots.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REGULATIONS Inspection Methods and Procedures § 800.85 Inspection of grain in combined lots. (a) General. The...) Weighted or mathematical average. Official factor and official criteria information shown on a certificate... section, be based on the weighted or mathematical averages of the analysis of the sublots in the lot and...

Evaluation of primary immunization coverage of infants under universal immunization programme in an urban area of bangalore city using cluster sampling and lot quality assurance sampling techniques.

PubMed

K, Punith; K, Lalitha; G, Suman; Bs, Pradeep; Kumar K, Jayanth

2008-07-01

Is LQAS technique better than cluster sampling technique in terms of resources to evaluate the immunization coverage in an urban area? To assess and compare the lot quality assurance sampling against cluster sampling in the evaluation of primary immunization coverage. Population-based cross-sectional study. Areas under Mathikere Urban Health Center. Children aged 12 months to 23 months. 220 in cluster sampling, 76 in lot quality assurance sampling. Percentages and Proportions, Chi square Test. (1) Using cluster sampling, the percentage of completely immunized, partially immunized and unimmunized children were 84.09%, 14.09% and 1.82%, respectively. With lot quality assurance sampling, it was 92.11%, 6.58% and 1.31%, respectively. (2) Immunization coverage levels as evaluated by cluster sampling technique were not statistically different from the coverage value as obtained by lot quality assurance sampling techniques. Considering the time and resources required, it was found that lot quality assurance sampling is a better technique in evaluating the primary immunization coverage in urban area.

Guidepost neurons for the lateral olfactory tract: expression of metabotropic glutamate receptor 1 and innervation by glutamatergic olfactory bulb axons.

PubMed

Hirata, Tatsumi; Kumada, Tatsuro; Kawasaki, Takahiko; Furukawa, Tomonori; Aiba, Atsu; Conquet, François; Saga, Yumiko; Fukuda, Atsuo

2012-12-01

The guidepost neurons for the lateral olfactory tract, which are called lot cells, are the earliest-generated neurons in the neocortex. They migrate tangentially and ventrally further down this tract, and provide scaffolding for the olfactory bulb axons projecting into this pathway. The molecular profiles of the lot cells are largely uncharacterized. We found that lot cells specifically express metabotropic glutamate receptor subtype-1 at a very early stage of development. This receptor is functionally competent and responds to a metabotropic glutamate receptor agonist with a transient increase in the intracellular calcium ion concentration. When the glutamatergic olfactory bulb axons were electrically stimulated, lot cells responded to the stimulation with a calcium increase mainly via ionotropic glutamate receptors, suggesting potential neurotransmission between the axons and lot cells during early development. Together with the finding that lot cells themselves are glutamatergic excitatory neurons, our results provide another notable example of precocious interactions between the projecting axons and their intermediate targets. Copyright © 2012 Wiley Periodicals, Inc.

Polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in harbor sediments from Sea Lots, Port-of-Spain, Trinidad and Tobago.

PubMed

Mohammed, Azad; Peterman, Paul; Echols, Kathy; Feltz, Kevin; Tegerdine, George; Manoo, Anton; Maraj, Dexter; Agard, John; Orazio, Carl

2011-06-01

Concentrations of polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) were determined in nearshore marine surficial sediments from three locations in Trinidad. Sediments were sampled at Sea Lots on the west coast, in south Port-of-Spain Harbor, south of Sea Lots at Caroni Lagoon National Park, and on Trinidad's east coast at Manzanilla. Total PCB concentrations in Sea Lots sediments ranged from 62 to 601ng/g (dry weight {dw}), which was higher than at Caroni and Manzanilla, 13 and 8ng/g dw, respectively. Total OCP concentrations at Sea Lots were ranged from 44.5 to 145ng/g dw, compared with 13.1 and 23.8n/g (dw), for Caroni and Manzanilla respectively. The concentrations of PCBs and of some OCPs in sediments from Sea Lots were above the Canadian interim sediment quality guidelines. To date, this data is the first report on the levels of PCBs and other organochlorine compounds from Trinidad and Tobago. Copyright © 2011 Elsevier Ltd. All rights reserved.

Photoresponsive Passive Micromixers Based on Spiropyran Size-Tunable Hydrogels.

PubMed

Ter Schiphorst, Jeroen; Melpignano, Giuseppe G; Amirabadi, Hossein Eslami; Houben, Menno H J M; Bakker, Sterre; den Toonder, Jaap M J; Schenning, Albertus P H J

2018-01-01

Microfluidic devices allow the manipulation of fluids down to the micrometer scale and are receiving a lot of attention for applications where low volumes and high throughputs are required. In these micro channels, laminar flow usually dominates, which requires long residence times of the fluids, limiting the flow speed and throughput. Here a switchable passive mixer has been developed to control mixing and to easily clean microchannels. The mixer is based on a photoresponsive spiropyran based hydrogel of which the dimensions can be tuned by changing the intensity of the light. The size-tunable gels have been used to fabricate a passive slanted groove mixer that can be switched off by light allowing to change mixing of microfluidics to non-mixed flows. These findings open new possibilities for multi-purpose microfluidic devices where mixers and valves can be tuned by light. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Intervene before leaving: clustered lot quality assurance sampling to monitor vaccination coverage at health district level before the end of a yellow fever and measles vaccination campaign in Sierra Leone in 2009.

PubMed

Pezzoli, Lorenzo; Conteh, Ishata; Kamara, Wogba; Gacic-Dobo, Marta; Ronveaux, Olivier; Perea, William A; Lewis, Rosamund F

2012-06-07

In November 2009, Sierra Leone conducted a preventive yellow fever (YF) vaccination campaign targeting individuals aged nine months and older in six health districts. The campaign was integrated with a measles follow-up campaign throughout the country targeting children aged 9-59 months. For both campaigns, the operational objective was to reach 95% of the target population. During the campaign, we used clustered lot quality assurance sampling (C-LQAS) to identify areas of low coverage to recommend timely mop-up actions. We divided the country in 20 non-overlapping lots. Twelve lots were targeted by both vaccinations, while eight only by measles. In each lot, five clusters of ten eligible individuals were selected for each vaccine. The upper threshold (UT) was set at 90% and the lower threshold (LT) at 75%. A lot was rejected for low vaccination coverage if more than 7 unvaccinated individuals (not presenting vaccination card) were found. After the campaign, we plotted the C-LQAS results against the post-campaign coverage estimations to assess if early interventions were successful enough to increase coverage in the lots that were at the level of rejection before the end of the campaign. During the last two days of campaign, based on card-confirmed vaccination status, five lots out of 20 (25.0%) failed for having low measles vaccination coverage and three lots out of 12 (25.0%) for low YF coverage. In one district, estimated post-campaign vaccination coverage for both vaccines was still not significantly above the minimum acceptable level (LT = 75%) even after vaccination mop-up activities. C-LQAS during the vaccination campaign was informative to identify areas requiring mop-up activities to reach the coverage target prior to leaving the region. The only district where mop-up activities seemed to be unsuccessful might have had logistical difficulties that should be further investigated and resolved.

CONARC Training Workshop, Fort Gordon, Georgia, 5-7 October 1971. Volume III. Educational Television and Training Films Specialty Workshop.

DTIC Science & Technology

1971-10-01

creative orgasm and you again splash yourself all over the control room, you don’t really care if there are kids out there, a lot of times to follow this... orgasm of a unic, that it has a lot of contortions, a lot of spasms, and a lot of moving around but no real issue. I generally agree with what you have...CONARC system that is over- stimulating anybody. My complaint is the opposite - we have all of these things and we haven’t used them. Granted you go with

Nonlinear Dynamical Model of a Soft Viscoelastic Dielectric Elastomer

NASA Astrophysics Data System (ADS)

Zhang, Junshi; Chen, Hualing; Li, Dichen

2017-12-01

Actuated by alternating stimulation, dielectric elastomers (DEs) show a behavior of complicated nonlinear vibration, implying a potential application as dynamic electromechanical actuators. As is well known, for a vibrational system, including the DE system, the dynamic properties are significantly affected by the geometrical sizes. In this article, a nonlinear dynamical model is deduced to investigate the geometrical effects on dynamic properties of viscoelastic DEs. The DEs with square and arbitrary rectangular geometries are considered, respectively. Besides, the effects of tensile forces on dynamic performances of rectangular DEs with comparably small and large geometrical sizes are explored. Phase paths and Poincaré maps are utilized to detect the periodicity of the nonlinear vibrations of DEs. The resonance characteristics of DEs incorporating geometrical effects are also investigated. The results indicate that the dynamic properties of DEs, including deformation response, vibrational periodicity, and resonance, are tuned when the geometrical sizes vary.

Dynamics of Research Team Formation in Complex Networks

NASA Astrophysics Data System (ADS)

Sun, Caihong; Wan, Yuzi; Chen, Yu

Most organizations encourage the formation of teams to accomplish complicated tasks, and vice verse, effective teams could bring lots benefits and profits for organizations. Network structure plays an important role in forming teams. In this paper, we specifically study the dynamics of team formation in large research communities in which knowledge of individuals plays an important role on team performance and individual utility. An agent-based model is proposed, in which heterogeneous agents from research communities are described and empirically tested. Each agent has a knowledge endowment and a preference for both income and leisure. Agents provide a variable input (‘effort’) and their knowledge endowments to production. They could learn from others in their team and those who are not in their team but have private connections in community to adjust their own knowledge endowment. They are allowed to join other teams or work alone when it is welfare maximizing to do so. Various simulation experiments are conducted to examine the impacts of network topology, knowledge diffusion among community network, and team output sharing mechanisms on the dynamics of team formation.

Determining the optimal vaccine vial size in developing countries: a Monte Carlo simulation approach.

PubMed

Dhamodharan, Aswin; Proano, Ruben A

2012-09-01

Outreach immunization services, in which health workers immunize children in their own communities, are indispensable to improve vaccine coverage in rural areas of developing countries. One of the challenges faced by these services is how to reduce high levels of vaccine wastage. In particular, the open vial wastage (OVW) that result from the vaccine doses remaining in a vial after a time for safe use -since opening the vial- has elapsed. This wastage is highly dependent on the choice of vial size and the expected number of participants for which the outreach session is planned (i.e., session size). The use single-dose vials results in zero OVW, but it increases the vaccine purchase, transportation, and holding costs per dose as compared to those resulting from using larger vial sizes. The OVW also decreases when more people are immunized in a session. However, controlling the actual number of people that show to an outreach session in rural areas of developing countries highly depends on factors that are out of control of the immunization planners. This paper integrates a binary integer-programming model to a Monte Carlo simulation method to determine the choice of vial size and the optimal reordering point level to implement an (nQ, r, T) lot-sizing policy that provides the best tradeoff between procurement costs and wastage.

Wrinkled alfalfa seeds harbor more aerobic bacteria and are more difficult to sanitize than smooth seeds.

PubMed

Charkowski, A O; Sarreal, C Z; Mandrell, R E

2001-09-01

At least 14 separate outbreaks of food poisoning attributed to either Salmonella enterica or Escherichia coli O157:H7 have been traced to sprouts in the past decade. Seeds contaminated with human pathogens caused most of these outbreaks, thus many sprout growers are now treating alfalfa seeds with the sanitizing agent, calcium hypochlorite (Ca[OCl]2), prior to sprouting. The efficacy of alfalfa seed sanitation varies between seed lots and between seeds within each lot. Alfalfa seeds from different seed lots were sorted by type in an effort to determine if certain seed types carry more aerobic bacteria than other seed types. Seeds with a wrinkled type, characteristic of lygus bug damage, had significantly higher levels of culturable aerobic bacteria and were more difficult to sanitize than smooth, healthy seeds. After sanitation, wrinkled alfalfa seeds that had been inoculated with S. enterica ser. Newport carried significantly higher levels of Salmonella Newport than smooth seeds. If S. enterica is present on wrinkled seeds in naturally contaminated seed lots, it may be difficult to chemically sanitize the seed lot. Removal of the wrinkled alfalfa seeds from the seed lots, perhaps by adapting color sorting equipment similar to that used to sort rice grains and other seeds, should reduce the level of aerobic bacteria in seed lots and may result in lower levels of human pathogens on contaminated alfalfa seeds.

21 CFR 203.38 - Sample lot or control numbers; labeling of sample units.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Sample lot or control numbers; labeling of sample units. 203.38 Section 203.38 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL PRESCRIPTION DRUG MARKETING Samples § 203.38 Sample lot or control...

49 CFR 178.33-8 - Tests.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Tests. 178.33-8 Section 178.33-8 Transportation... Containers, and Linings § 178.33-8 Tests. (a) One out of each lot of 25,000 containers or less, successively..., successively produced per day, shall constitute a lot and if the test container shall fail, the lot shall be...

49 CFR 178.33-8 - Tests.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Tests. 178.33-8 Section 178.33-8 Transportation... Containers, and Linings § 178.33-8 Tests. (a) One out of each lot of 25,000 containers or less, successively..., successively produced per day, shall constitute a lot and if the test container shall fail, the lot shall be...

49 CFR 178.33-8 - Tests.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Tests. 178.33-8 Section 178.33-8 Transportation... Containers, and Linings § 178.33-8 Tests. (a) One out of each lot of 25,000 containers or less, successively..., successively produced per day, shall constitute a lot and if the test container shall fail, the lot shall be...

49 CFR 178.33-8 - Tests.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Tests. 178.33-8 Section 178.33-8 Transportation... Containers, and Linings § 178.33-8 Tests. (a) One out of each lot of 25,000 containers or less, successively..., successively produced per day, shall constitute a lot and if the test container shall fail, the lot shall be...

7 CFR 1427.170 - Quantity for loan.

Code of Federal Regulations, 2010 CFR

2010-01-01

... necessary to protect the interests of CCC on the basis of one or more of the following risk factors: (1... turnout factor determined under paragraph (b) of this section. (b) The lint turnout factor for any lot of... initial inspection of the lot. If a control portion of the lot is weighed and ginned, the turnout factor...

7 CFR 1427.170 - Quantity for loan.

Code of Federal Regulations, 2011 CFR

2011-01-01

... necessary to protect the interests of CCC on the basis of one or more of the following risk factors: (1... turnout factor determined under paragraph (b) of this section. (b) The lint turnout factor for any lot of... initial inspection of the lot. If a control portion of the lot is weighed and ginned, the turnout factor...

7 CFR 52.38c - Statistical sampling procedures for lot inspection of processed fruits and vegetables by attributes.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Statistical sampling procedures for lot inspection of processed fruits and vegetables by attributes. 52.38c Section 52.38c Agriculture Regulations of the... Regulations Governing Inspection and Certification Sampling § 52.38c Statistical sampling procedures for lot...

Three Permeable Pavements Performances for Priority Metal Pollutants and Metals associated with Deicing Chemicals from Edison Parking Lot, NJ - abstract

EPA Science Inventory

The U.S. Environmental Protection Agency constructed a 4000-m2 parking lot in Edison, New Jersey in 2009. The parking lot is surfaced with three permeable pavements [permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA)]. Samples of each p...

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

7 CFR 42.123 - Flow diagram for skip lot sampling and inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Flow diagram for skip lot sampling and inspection. 42.123 Section 42.123 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING... Procedures § 42.123 Flow diagram for skip lot sampling and inspection. EC02SE91.000 Notes: 1. Only normal...

7 CFR 52.38c - Statistical sampling procedures for lot inspection of processed fruits and vegetables by attributes.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Statistical sampling procedures for lot inspection of processed fruits and vegetables by attributes. 52.38c Section 52.38c Agriculture Regulations of the... Regulations Governing Inspection and Certification Sampling § 52.38c Statistical sampling procedures for lot...

Comparative analyses of industrial-scale human platelet lysate preparations.

PubMed

Pierce, Jan; Benedetti, Eric; Preslar, Amber; Jacobson, Pam; Jin, Ping; Stroncek, David F; Reems, Jo-Anna

2017-12-01

Efforts are underway to eliminate fetal bovine serum from mammalian cell cultures for clinical use. An emerging, viable replacement option for fetal bovine serum is human platelet lysate (PL) as either a plasma-based or serum-based product. Nine industrial-scale, serum-based PL manufacturing runs (i.e., lots) were performed, consisting of an average ± standard deviation volume of 24.6 ± 2.2 liters of pooled, platelet-rich plasma units that were obtained from apheresis donors. Manufactured lots were compared by evaluating various biochemical and functional test results. Comprehensive cytokine profiles of PL lots and product stability tests were performed. Global gene expression profiles of mesenchymal stromal cells (MSCs) cultured with plasma-based or serum-based PL were compared to MSCs cultured with fetal bovine serum. Electrolyte and protein levels were relatively consistent among all serum-based PL lots, with only slight variations in glucose and calcium levels. All nine lots were as good as or better than fetal bovine serum in expanding MSCs. Serum-based PL stored at -80°C remained stable over 2 years. Quantitative cytokine arrays showed similarities as well as dissimilarities in the proteins present in serum-based PL. Greater differences in MSC gene expression profiles were attributable to the starting cell source rather than with the use of either PL or fetal bovine serum as a culture supplement. Using a large-scale, standardized method, lot-to-lot variations were noted for industrial-scale preparations of serum-based PL products. However, all lots performed as well as or better than fetal bovine serum in supporting MSC growth. Together, these data indicate that off-the-shelf PL is a feasible substitute for fetal bovine serum in MSC cultures. © 2017 AABB.

Comparison of surgically induced astigmatism following different glaucoma operations.

PubMed

Tanito, Masaki; Matsuzaki, Yukari; Ikeda, Yoshifumi; Fujihara, Etsuko

2017-01-01

To compare surgically induced astigmatism (SIA) among glaucomatous eyes treated with trabeculectomy (LEC), EX-PRESS ® shunt (EXP), ab externo trabeculotomy (exLOT), or microhook ab interno trabeculotomy (μLOT). Eighty right eyes of 80 subjects who underwent LEC (n=20), EXP (n=20), exLOT (n=20), or μLOT (n=20) were included. The dataset including the best-corrected visual acuity (BCVA), intraocular pressure (IOP), and keratometry recordings preoperatively and 3 months postoperatively was collected by chart review. The means of the vector magnitude, vector meridian, and arithmetic magnitude of the preoperative and postoperative astigmatism and SIA were calculated. The correlations among the SIA magnitude, postoperative BCVA, and IOP were assessed. The mean astigmatic arithmetic magnitudes did not differ significantly ( P =0.0732) preoperatively among the four groups, but the magnitude was significantly ( P =0.0002) greater in the LEC group than the other groups postoperatively. The mean SIA vectors were calculated to be 1.01 D at 56°, 0.62 D at 74°, 0.23 D at 112°, and 0.12 D at 97° for the LEC, EXP, exLOT, and μLOT groups, respectively. The mean SIA arithmetic magnitudes were significantly ( P <0.0001) greater in the LEC group than the other groups. Three months postoperatively, the SIA magnitude was correlated positively with the logarithm of the minimum angle of resolution (logMAR) BCVA ( r =0.3538) and negatively with the IOP ( r =-0.3265); the logMAR BCVA was correlated negatively with the IOP ( r =-0.3105). EXP, exLOT, and μLOT induce less corneal astigmatism than LEC in the early postoperative period.

Design of a sampling plan to detect ochratoxin A in green coffee.

PubMed

Vargas, E A; Whitaker, T B; Dos Santos, E A; Slate, A B; Lima, F B; Franca, R C A

2006-01-01

The establishment of maximum limits for ochratoxin A (OTA) in coffee by importing countries requires that coffee-producing countries develop scientifically based sampling plans to assess OTA contents in lots of green coffee before coffee enters the market thus reducing consumer exposure to OTA, minimizing the number of lots rejected, and reducing financial loss for producing countries. A study was carried out to design an official sampling plan to determine OTA in green coffee produced in Brazil. Twenty-five lots of green coffee (type 7 - approximately 160 defects) were sampled according to an experimental protocol where 16 test samples were taken from each lot (total of 16 kg) resulting in a total of 800 OTA analyses. The total, sampling, sample preparation, and analytical variances were 10.75 (CV = 65.6%), 7.80 (CV = 55.8%), 2.84 (CV = 33.7%), and 0.11 (CV = 6.6%), respectively, assuming a regulatory limit of 5 microg kg(-1) OTA and using a 1 kg sample, Romer RAS mill, 25 g sub-samples, and high performance liquid chromatography. The observed OTA distribution among the 16 OTA sample results was compared to several theoretical distributions. The 2 parameter-log normal distribution was selected to model OTA test results for green coffee as it gave the best fit across all 25 lot distributions. Specific computer software was developed using the variance and distribution information to predict the probability of accepting or rejecting coffee lots at specific OTA concentrations. The acceptation probability was used to compute an operating characteristic (OC) curve specific to a sampling plan design. The OC curve was used to predict the rejection of good lots (sellers' or exporters' risk) and the acceptance of bad lots (buyers' or importers' risk).

Comparison of surgically induced astigmatism following different glaucoma operations

PubMed Central

Tanito, Masaki; Matsuzaki, Yukari; Ikeda, Yoshifumi; Fujihara, Etsuko

2017-01-01

Aim To compare surgically induced astigmatism (SIA) among glaucomatous eyes treated with trabeculectomy (LEC), EX-PRESS® shunt (EXP), ab externo trabeculotomy (exLOT), or microhook ab interno trabeculotomy (μLOT). Subjects and methods Eighty right eyes of 80 subjects who underwent LEC (n=20), EXP (n=20), exLOT (n=20), or μLOT (n=20) were included. The dataset including the best-corrected visual acuity (BCVA), intraocular pressure (IOP), and keratometry recordings preoperatively and 3 months postoperatively was collected by chart review. The means of the vector magnitude, vector meridian, and arithmetic magnitude of the preoperative and postoperative astigmatism and SIA were calculated. The correlations among the SIA magnitude, postoperative BCVA, and IOP were assessed. Results The mean astigmatic arithmetic magnitudes did not differ significantly (P=0.0732) preoperatively among the four groups, but the magnitude was significantly (P=0.0002) greater in the LEC group than the other groups postoperatively. The mean SIA vectors were calculated to be 1.01 D at 56°, 0.62 D at 74°, 0.23 D at 112°, and 0.12 D at 97° for the LEC, EXP, exLOT, and μLOT groups, respectively. The mean SIA arithmetic magnitudes were significantly (P<0.0001) greater in the LEC group than the other groups. Three months postoperatively, the SIA magnitude was correlated positively with the logarithm of the minimum angle of resolution (logMAR) BCVA (r=0.3538) and negatively with the IOP (r=−0.3265); the logMAR BCVA was correlated negatively with the IOP (r=−0.3105). Conclusion EXP, exLOT, and μLOT induce less corneal astigmatism than LEC in the early postoperative period. PMID:29238159