Two stage gear tooth dynamics program

NASA Technical Reports Server (NTRS)

Boyd, Linda S.

1989-01-01

The epicyclic gear dynamics program was expanded to add the option of evaluating the tooth pair dynamics for two epicyclic gear stages with peripheral components. This was a practical extension to the program as multiple gear stages are often used for speed reduction, space, weight, and/or auxiliary units. The option was developed for either stage to be a basic planetary, star, single external-external mesh, or single external-internal mesh. The two stage system allows for modeling of the peripherals with an input mass and shaft, an output mass and shaft, and a connecting shaft. Execution of the initial test case indicated an instability in the solution with the tooth paid loads growing to excessive magnitudes. A procedure to trace the instability is recommended as well as a method of reducing the program's computation time by reducing the number of boundary condition iterations.

DYNSYL: a general-purpose dynamic simulator for chemical processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patterson, G.K.; Rozsa, R.B.

1978-09-05

Lawrence Livermore Laboratory is conducting a safeguards program for the Nuclear Regulatory Commission. The goal of the Material Control Project of this program is to evaluate material control and accounting (MCA) methods in plants that handle special nuclear material (SNM). To this end we designed and implemented the dynamic chemical plant simulation program DYNSYL. This program can be used to generate process data or to provide estimates of process performance; it simulates both steady-state and dynamic behavior. The MCA methods that may have to be evaluated range from sophisticated on-line material trackers such as Kalman filter estimators, to relatively simplemore » material balance procedures. This report describes the overall structure of DYNSYL and includes some example problems. The code is still in the experimental stage and revision is continuing.« less

Procedure for estimating stability and control parameters from flight test data by using maximum likelihood methods employing a real-time digital system

NASA Technical Reports Server (NTRS)

Grove, R. D.; Bowles, R. L.; Mayhew, S. C.

1972-01-01

A maximum likelihood parameter estimation procedure and program were developed for the extraction of the stability and control derivatives of aircraft from flight test data. Nonlinear six-degree-of-freedom equations describing aircraft dynamics were used to derive sensitivity equations for quasilinearization. The maximum likelihood function with quasilinearization was used to derive the parameter change equations, the covariance matrices for the parameters and measurement noise, and the performance index function. The maximum likelihood estimator was mechanized into an iterative estimation procedure utilizing a real time digital computer and graphic display system. This program was developed for 8 measured state variables and 40 parameters. Test cases were conducted with simulated data for validation of the estimation procedure and program. The program was applied to a V/STOL tilt wing aircraft, a military fighter airplane, and a light single engine airplane. The particular nonlinear equations of motion, derivation of the sensitivity equations, addition of accelerations into the algorithm, operational features of the real time digital system, and test cases are described.

Science Notes.

ERIC Educational Resources Information Center

School Science Review, 1984

1984-01-01

Presents 26 activities, experiments, demonstrations, games, and computer programs for biology, chemistry, and physics. Background information, laboratory procedures, equipment lists, and instructional strategies are given. Topics include eye measurements, nutrition, soil test tube rack, population dynamics, angular momentum, transition metals,…

The NASTRAN theoretical manual

NASA Technical Reports Server (NTRS)

1981-01-01

Designed to accommodate additions and modifications, this commentary on NASTRAN describes the problem solving capabilities of the program in a narrative fashion and presents developments of the analytical and numerical procedures that underlie the program. Seventeen major sections and numerous subsections cover; the organizational aspects of the program, utility matrix routines, static structural analysis, heat transfer, dynamic structural analysis, computer graphics, special structural modeling techniques, error analysis, interaction between structures and fluids, and aeroelastic analysis.

Technology development of fabrication techniques for advanced solar dynamic concentrators

NASA Technical Reports Server (NTRS)

Richter, Scott W.

1991-01-01

The objective of the advanced concentrator program is to develop the technology that will lead to lightweight, highly reflective, accurate, scaleable, and long lived space solar dynamic concentrators. The advanced concentrator program encompasses new and innovative concepts, fabrication techniques, materials selection, and simulated space environmental testing. Fabrication techniques include methods of fabricating the substrates and coating substrate surfaces to produce high quality optical surfaces, acceptable for further coating with vapor deposited optical films. The selected materials to obtain a high quality optical surface include microsheet glass and Eccocoat EP-3 epoxy, with DC-93-500 selected as a candidate silicone adhesive and levelizing layer. The following procedures are defined: cutting, cleaning, forming, and bonding microsheet glass. Procedures are also defined for surface cleaning, and EP-3 epoxy application. The results and analyses from atomic oxygen and thermal cycling tests are used to determine the effects of orbital conditions in a space environment.

Gear Drive Testing

NASA Technical Reports Server (NTRS)

1982-01-01

Philadelphia Gear Corporation used two COSMIC computer programs; one dealing with shrink fit analysis and the other with rotor dynamics problems in computerized design and test work. The programs were used to verify existing in-house programs to insure design accuracy by checking its company-developed computer methods against procedures developed by other organizations. Its specialty is in custom units for unique applications, such as Coast Guard ice breaking ships, steel mill drives, coal crusher, sewage treatment equipment and electricity.

A Polyhedral Outer-approximation, Dynamic-discretization optimization solver, 1.x

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bent, Rusell; Nagarajan, Harsha; Sundar, Kaarthik

2017-09-25

In this software, we implement an adaptive, multivariate partitioning algorithm for solving mixed-integer nonlinear programs (MINLP) to global optimality. The algorithm combines ideas that exploit the structure of convex relaxations to MINLPs and bound tightening procedures

DEAN: A program for dynamic engine analysis

NASA Technical Reports Server (NTRS)

Sadler, G. G.; Melcher, K. J.

1985-01-01

The Dynamic Engine Analysis program, DEAN, is a FORTRAN code implemented on the IBM/370 mainframe at NASA Lewis Research Center for digital simulation of turbofan engine dynamics. DEAN is an interactive program which allows the user to simulate engine subsystems as well as a full engine systems with relative ease. The nonlinear first order ordinary differential equations which define the engine model may be solved by one of four integration schemes, a second order Runge-Kutta, a fourth order Runge-Kutta, an Adams Predictor-Corrector, or Gear's method for still systems. The numerical data generated by the model equations are displayed at specified intervals between which the user may choose to modify various parameters affecting the model equations and transient execution. Following the transient run, versatile graphics capabilities allow close examination of the data. DEAN's modeling procedure and capabilities are demonstrated by generating a model of simple compressor rig.

The IHS diagnostic X-ray equipment radiation protection program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knapp, A.; Byrns, G.; Suleiman, O.

The Indian Health Service (IHS) operates or contracts with Tribal groups to operate 50 hospitals and approximately 165 primary ambulatory care centers. These facilities contain approximately 275 medical and 800 dental diagnostic x-ray machines. IHS environmental health personnel in collaboration with the Food and Drug Administration's (FDA) Center for Devices and Radiological Health (CDRH) developed a diagnostic x-ray protection program including standard survey procedures and menu-driven calculations software. Important features of the program include the evaluation of equipment performance collection of average patient entrance skin exposure (ESE) measurements for selected procedures, and quality assurance. The ESE data, collected using themore » National Evaluation of X-ray Trends (NEXT) protocol, will be presented. The IHS Diagnostic X-ray Radiation Protection Program is dynamic and is adapting to changes in technology and workload.« less

Development tests for the 2.5 megawatt Mod-2 wind turbine generator

NASA Technical Reports Server (NTRS)

Andrews, J. S.; Baskin, J. M.

1982-01-01

The 2.5 megawatt MOD-2 wind turbine generator test program is discussed. The development of the 2.5 megawatt MOD-2 wind turbine generator included an extensive program of testing which encompassed verification of analytical procedures, component development, and integrated system verification. The test program was to assure achievement of the thirty year design operational life of the wind turbine system as well as to minimize costly design modifications which would otherwise have been required during on site system testing. Computer codes were modified, fatigue life of structure and dynamic components were verified, mechanical and electrical component and subsystems were functionally checked and modified where necessary to meet system specifications, and measured dynamic responses of coupled systems confirmed analytical predictions.

DIALOG: An executive computer program for linking independent programs

NASA Technical Reports Server (NTRS)

Glatt, C. R.; Hague, D. S.; Watson, D. A.

1973-01-01

A very large scale computer programming procedure called the DIALOG executive system was developed for the CDC 6000 series computers. The executive computer program, DIALOG, controls the sequence of execution and data management function for a library of independent computer programs. Communication of common information is accomplished by DIALOG through a dynamically constructed and maintained data base of common information. Each computer program maintains its individual identity and is unaware of its contribution to the large scale program. This feature makes any computer program a candidate for use with the DIALOG executive system. The installation and uses of the DIALOG executive system are described.

An investigation of angular stiffness and damping coefficients of an axial spline coupling in high-speed rotating machinery

NASA Technical Reports Server (NTRS)

Ku, C.-P. Roger; Walton, James F., Jr.; Lund, Jorgen W.

1994-01-01

This paper provided an opportunity to quantify the angular stiffness and equivalent viscous damping coefficients of an axial spline coupling used in high-speed turbomachinery. A unique test methodology and data reduction procedures were developed. The bending moments and angular deflections transmitted across an axial spline coupling were measured while a nonrotating shaft was excited by an external shaker. A rotor dynamics computer program was used to simulate the test conditions and to correlate the angular stiffness and damping coefficients. In addition, sensitivity analyses were performed to show that the accuracy of the dynamic coefficients do not rely on the accuracy of the data reduction procedures.

Oxford International Conference on the Mechanical Properties of Materials at High Rates of Strain (4th) Held in Oxford, United Kingdom on 19-22 March 1989

DTIC Science & Technology

1989-03-22

models are used in the computer program EPIC2 to describe the structural response in the cylinder impact test are compared and the differences are...Inc. 8600 Le Salle Road Suite 614, Oxford Building Towson, Maryland 21204 This paper describes the development and application of a computer program ...performed using a dynamic viscoplastic finite element computer program . The resolution of the procedure has been investigated by obtaining replicate

A vibration-based health monitoring program for a large and seismically vulnerable masonry dome

NASA Astrophysics Data System (ADS)

Pecorelli, M. L.; Ceravolo, R.; De Lucia, G.; Epicoco, R.

2017-05-01

Vibration-based health monitoring of monumental structures must rely on efficient and, as far as possible, automatic modal analysis procedures. Relatively low excitation energy provided by traffic, wind and other sources is usually sufficient to detect structural changes, as those produced by earthquakes and extreme events. Above all, in-operation modal analysis is a non-invasive diagnostic technique that can support optimal strategies for the preservation of architectural heritage, especially if complemented by model-driven procedures. In this paper, the preliminary steps towards a fully automated vibration-based monitoring of the world’s largest masonry oval dome (internal axes of 37.23 by 24.89 m) are presented. More specifically, the paper reports on signal treatment operations conducted to set up the permanent dynamic monitoring system of the dome and to realise a robust automatic identification procedure. Preliminary considerations on the effects of temperature on dynamic parameters are finally reported.

A new procedure for dynamic adaption of three-dimensional unstructured grids

NASA Technical Reports Server (NTRS)

Biswas, Rupak; Strawn, Roger

1993-01-01

A new procedure is presented for the simultaneous coarsening and refinement of three-dimensional unstructured tetrahedral meshes. This algorithm allows for localized grid adaption that is used to capture aerodynamic flow features such as vortices and shock waves in helicopter flowfield simulations. The mesh-adaption algorithm is implemented in the C programming language and uses a data structure consisting of a series of dynamically-allocated linked lists. These lists allow the mesh connectivity to be rapidly reconstructed when individual mesh points are added and/or deleted. The algorithm allows the mesh to change in an anisotropic manner in order to efficiently resolve directional flow features. The procedure has been successfully implemented on a single processor of a Cray Y-MP computer. Two sample cases are presented involving three-dimensional transonic flow. Computed results show good agreement with conventional structured-grid solutions for the Euler equations.

Ground resonance analysis using a substructure modeling approach

NASA Technical Reports Server (NTRS)

Chen, S.-Y.; Berman, A.; Austin, E. E.

1984-01-01

A convenient and versatile procedure for modeling and analyzing ground resonance phenomena is described and illustrated. A computer program is used which dynamically couples differential equations with nonlinear and time dependent coefficients. Each set of differential equations may represent a component such as a rotor, fuselage, landing gear, or a failed damper. Arbitrary combinations of such components may be formulated into a model of a system. When the coupled equations are formed, a procedure is executed which uses a Floquet analysis to determine the stability of the system. Illustrations of the use of the procedures along with the numerical examples are presented.

Ground resonance analysis using a substructure modeling approach

NASA Technical Reports Server (NTRS)

Chen, S. Y.; Austin, E. E.; Berman, A.

1985-01-01

A convenient and versatile procedure for modeling and analyzing ground resonance phenomena is described and illustrated. A computer program is used which dynamically couples differential equations with nonlinear and time dependent coefficients. Each set of differential equations may represent a component such as a rotor, fuselage, landing gear, or a failed damper. Arbitrary combinations of such components may be formulated into a model of a system. When the coupled equations are formed, a procedure is executed which uses a Floquet analysis to determine the stability of the system. Illustrations of the use of the procedures along with the numerical examples are presented.

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: McDonnell-Douglas Helicopter Company achievements

NASA Technical Reports Server (NTRS)

Toossi, Mostafa; Weisenburger, Richard; Hashemi-Kia, Mostafa

1993-01-01

This paper presents a summary of some of the work performed by McDonnell Douglas Helicopter Company under NASA Langley-sponsored rotorcraft structural dynamics program known as DAMVIBS (Design Analysis Methods for VIBrationS). A set of guidelines which is applicable to dynamic modeling, analysis, testing, and correlation of both helicopter airframes and a large variety of structural finite element models is presented. Utilization of these guidelines and the key features of their applications to vibration modeling of helicopter airframes are discussed. Correlation studies with the test data, together with the development and applications of a set of efficient finite element model checkout procedures, are demonstrated on a large helicopter airframe finite element model. Finally, the lessons learned and the benefits resulting from this program are summarized.

Automated processing of dynamic properties of intraventricular pressure by computer program and electronic circuit.

PubMed

Adler, D; Mahler, Y

1980-04-01

A procedure for automatic detection and digital processing of the maximum first derivative of the intraventricular pressure (dp/dtmax), time to dp/dtmax(t - dp/dt) and beat-to-beat intervals have been developed. The procedure integrates simple electronic circuits with a short program using a simple algorithm for the detection of the points of interest. The tasks of differentiating the pressure signal and detecting the onset of contraction were done by electronics, while the tasks of finding the values of dp/dtmax, t - dp/dt, beat-to-beat intervals and all computations needed were done by software. Software/hardware 'trade off' considerations and the accuracy and reliability of the system are discussed.

DORCA computer program. Volume 1: User's guide

NASA Technical Reports Server (NTRS)

Wray, S. T., Jr.

1971-01-01

The Dynamic Operational Requirements and Cost Analysis Program (DORCA) was written to provide a top level analysis tool for NASA. DORCA relies on a man-machine interaction to optimize results based on external criteria. DORCA relies heavily on outside sources to provide cost information and vehicle performance parameters as the program does not determine these quantities but rather uses them. Given data describing missions, vehicles, payloads, containers, space facilities, schedules, cost values and costing procedures, the program computes flight schedules, cargo manifests, vehicle fleet requirements, acquisition schedules and cost summaries. The program is designed to consider the Earth Orbit, Lunar, Interplanetary and Automated Satellite Programs. A general outline of the capabilities of the program are provided.

Flight Dynamics Operations: Methods and Lessons Learned from Space Shuttle Orbit Operations

NASA Technical Reports Server (NTRS)

Cutri-Kohart, Rebecca M.

2011-01-01

The Flight Dynamics Officer is responsible for trajectory maintenance of the Space Shuttle. This paper will cover high level operational considerations, methodology, procedures, and lessons learned involved in performing the functions of orbit and rendezvous Flight Dynamics Officer and leading the team of flight dynamics specialists during different phases of flight. The primary functions that will be address are: onboard state vector maintenance, ground ephemeris maintenance, calculation of ground and spacecraft acquisitions, collision avoidance, burn targeting for the primary mission, rendezvous, deorbit and contingencies, separation sequences, emergency deorbit preparation, mass properties coordination, payload deployment planning, coordination with the International Space Station, and coordination with worldwide trajectory customers. Each of these tasks require the Flight Dynamics Officer to have cognizance of the current trajectory state as well as the impact of future events on the trajectory plan in order to properly analyze and react to real-time changes. Additionally, considerations are made to prepare flexible alternative trajectory plans in the case timeline changes or a systems failure impact the primary plan. The evolution of the methodology, procedures, and techniques used by the Flight Dynamics Officer to perform these tasks will be discussed. Particular attention will be given to how specific Space Shuttle mission and training simulation experiences, particularly off-nominal or unexpected events such as shortened mission durations, tank failures, contingency deorbit, navigation errors, conjunctions, and unexpected payload deployments, have influenced the operational procedures and training for performing Space Shuttle flight dynamics operations over the history of the program. These lessons learned can then be extended to future vehicle trajectory operations.

NASA/FAA general aviation crash dynamics program - An update

NASA Technical Reports Server (NTRS)

Hayduk, R. J.; Thomson, R. G.; Carden, H. D.

1979-01-01

Work in progress in the NASA/FAA General Aviation Crash Dynamics Program for the development of technology for increased crash-worthiness and occupant survivability of general aviation aircraft is presented. Full-scale crash testing facilities and procedures are outlined, and a chronological summary of full-scale tests conducted and planned is presented. The Plastic and Large Deflection Analysis of Nonlinear Structures and Modified Seat Occupant Model for Light Aircraft computer programs which form part of the effort to predict nonlinear geometric and material behavior of sheet-stringer aircraft structures subjected to large deformations are described, and excellent agreement between simulations and experiments is noted. The development of structural concepts to attenuate the load transmitted to the passenger through the seats and subfloor structure is discussed, and an apparatus built to test emergency locator transmitters in a realistic environment is presented.

A review of selected inorganic surface water quality-monitoring practices: are we really measuring what we think, and if so, are we doing it right?

USGS Publications Warehouse

Horowitz, Arthur J.

2013-01-01

Successful environmental/water quality-monitoring programs usually require a balance between analytical capabilities, the collection and preservation of representative samples, and available financial/personnel resources. Due to current economic conditions, monitoring programs are under increasing pressure to do more with less. Hence, a review of current sampling and analytical methodologies, and some of the underlying assumptions that form the bases for these programs seems appropriate, to see if they are achieving their intended objectives within acceptable error limits and/or measurement uncertainty, in a cost-effective manner. That evaluation appears to indicate that several common sampling/processing/analytical procedures (e.g., dip (point) samples/measurements, nitrogen determinations, total recoverable analytical procedures) are generating biased or nonrepresentative data, and that some of the underlying assumptions relative to current programs, such as calendar-based sampling and stationarity are no longer defensible. The extensive use of statistical models as well as surrogates (e.g., turbidity) also needs to be re-examined because the hydrologic interrelationships that support their use tend to be dynamic rather than static. As a result, a number of monitoring programs may need redesigning, some sampling and analytical procedures may need to be updated, and model/surrogate interrelationships may require recalibration.

Direct evaluation of fault trees using object-oriented programming techniques

NASA Technical Reports Server (NTRS)

Patterson-Hine, F. A.; Koen, B. V.

1989-01-01

Object-oriented programming techniques are used in an algorithm for the direct evaluation of fault trees. The algorithm combines a simple bottom-up procedure for trees without repeated events with a top-down recursive procedure for trees with repeated events. The object-oriented approach results in a dynamic modularization of the tree at each step in the reduction process. The algorithm reduces the number of recursive calls required to solve trees with repeated events and calculates intermediate results as well as the solution of the top event. The intermediate results can be reused if part of the tree is modified. An example is presented in which the results of the algorithm implemented with conventional techniques are compared to those of the object-oriented approach.

An Evaluative Review of Simulated Dynamic Smart 3d Objects

NASA Astrophysics Data System (ADS)

Romeijn, H.; Sheth, F.; Pettit, C. J.

2012-07-01

Three-dimensional (3D) modelling of plants can be an asset for creating agricultural based visualisation products. The continuum of 3D plants models ranges from static to dynamic objects, also known as smart 3D objects. There is an increasing requirement for smarter simulated 3D objects that are attributed mathematically and/or from biological inputs. A systematic approach to plant simulation offers significant advantages to applications in agricultural research, particularly in simulating plant behaviour and the influences of external environmental factors. This approach of 3D plant object visualisation is primarily evident from the visualisation of plants using photographed billboarded images, to more advanced procedural models that come closer to simulating realistic virtual plants. However, few programs model physical reactions of plants to external factors and even fewer are able to grow plants based on mathematical and/or biological parameters. In this paper, we undertake an evaluation of plant-based object simulation programs currently available, with a focus upon the components and techniques involved in producing these objects. Through an analytical review process we consider the strengths and weaknesses of several program packages, the features and use of these programs and the possible opportunities in deploying these for creating smart 3D plant-based objects to support agricultural research and natural resource management. In creating smart 3D objects the model needs to be informed by both plant physiology and phenology. Expert knowledge will frame the parameters and procedures that will attribute the object and allow the simulation of dynamic virtual plants. Ultimately, biologically smart 3D virtual plants that react to changes within an environment could be an effective medium to visually represent landscapes and communicate land management scenarios and practices to planners and decision-makers.

MONTE CARLO SIMULATIONS OF PERIODIC PULSED REACTOR WITH MOVING GEOMETRY PARTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Yan; Gohar, Yousry

2015-11-01

In a periodic pulsed reactor, the reactor state varies periodically from slightly subcritical to slightly prompt supercritical for producing periodic power pulses. Such periodic state change is accomplished by a periodic movement of specific reactor parts, such as control rods or reflector sections. The analysis of such reactor is difficult to perform with the current reactor physics computer programs. Based on past experience, the utilization of the point kinetics approximations gives considerable errors in predicting the magnitude and the shape of the power pulse if the reactor has significantly different neutron life times in different zones. To accurately simulate themore » dynamics of this type of reactor, a Monte Carlo procedure using the transfer function TRCL/TR of the MCNP/MCNPX computer programs is utilized to model the movable reactor parts. In this paper, two algorithms simulating the geometry part movements during a neutron history tracking have been developed. Several test cases have been developed to evaluate these procedures. The numerical test cases have shown that the developed algorithms can be utilized to simulate the reactor dynamics with movable geometry parts.« less

A Framework for Dynamic Constraint Reasoning Using Procedural Constraints

NASA Technical Reports Server (NTRS)

Jonsson, Ari K.; Frank, Jeremy D.

1999-01-01

Many complex real-world decision and control problems contain an underlying constraint reasoning problem. This is particularly evident in a recently developed approach to planning, where almost all planning decisions are represented by constrained variables. This translates a significant part of the planning problem into a constraint network whose consistency determines the validity of the plan candidate. Since higher-level choices about control actions can add or remove variables and constraints, the underlying constraint network is invariably highly dynamic. Arbitrary domain-dependent constraints may be added to the constraint network and the constraint reasoning mechanism must be able to handle such constraints effectively. Additionally, real problems often require handling constraints over continuous variables. These requirements present a number of significant challenges for a constraint reasoning mechanism. In this paper, we introduce a general framework for handling dynamic constraint networks with real-valued variables, by using procedures to represent and effectively reason about general constraints. The framework is based on a sound theoretical foundation, and can be proven to be sound and complete under well-defined conditions. Furthermore, the framework provides hybrid reasoning capabilities, as alternative solution methods like mathematical programming can be incorporated into the framework, in the form of procedures.

DIALOG: An executive computer program for linking independent programs

NASA Technical Reports Server (NTRS)

Glatt, C. R.; Hague, D. S.; Watson, D. A.

1973-01-01

A very large scale computer programming procedure called the DIALOG Executive System has been developed for the Univac 1100 series computers. The executive computer program, DIALOG, controls the sequence of execution and data management function for a library of independent computer programs. Communication of common information is accomplished by DIALOG through a dynamically constructed and maintained data base of common information. The unique feature of the DIALOG Executive System is the manner in which computer programs are linked. Each program maintains its individual identity and as such is unaware of its contribution to the large scale program. This feature makes any computer program a candidate for use with the DIALOG Executive System. The installation and use of the DIALOG Executive System are described at Johnson Space Center.

Investigation on the use of optimization techniques for helicopter airframe vibrations design studies

NASA Technical Reports Server (NTRS)

Sreekanta Murthy, T.

1992-01-01

Results of the investigation of formal nonlinear programming-based numerical optimization techniques of helicopter airframe vibration reduction are summarized. The objective and constraint function and the sensitivity expressions used in the formulation of airframe vibration optimization problems are presented and discussed. Implementation of a new computational procedure based on MSC/NASTRAN and CONMIN in a computer program system called DYNOPT for optimizing airframes subject to strength, frequency, dynamic response, and dynamic stress constraints is described. An optimization methodology is proposed which is thought to provide a new way of applying formal optimization techniques during the various phases of the airframe design process. Numerical results obtained from the application of the DYNOPT optimization code to a helicopter airframe are discussed.

Thermoelectric materials evaluation program. Technical summary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinderman, J.D.

1979-04-01

Research progress on the thermoelectric materials evaluation program is reported covering the period January 1, 1976 to September 30, 1978. Topical reports are presented on (1) hot and cold end ..delta..T's, (2) hardware mobility, (3) p-leg sublimation suppression, (4) thermodynamic stability of p-legs, (5) n-leg material process improvements to reduce extraneous resistance, (6) n-leg cracking, (7) dynamic evaluation of converter, and (8) data base and degradation modes. Twenty attachments are included which present supporting drawings, specifications, procedures, and data. (WHK)

Synthesis of aircraft structures using integrated design and analysis methods

NASA Technical Reports Server (NTRS)

Sobieszczanski-Sobieski, J.; Goetz, R. C.

1978-01-01

A systematic research is reported to develop and validate methods for structural sizing of an airframe designed with the use of composite materials and active controls. This research program includes procedures for computing aeroelastic loads, static and dynamic aeroelasticity, analysis and synthesis of active controls, and optimization techniques. Development of the methods is concerned with the most effective ways of integrating and sequencing the procedures in order to generate structural sizing and the associated active control system, which is optimal with respect to a given merit function constrained by strength and aeroelasticity requirements.

Quality control procedures for dynamic treatment delivery techniques involving couch motion.

PubMed

Yu, Victoria Y; Fahimian, Benjamin P; Xing, Lei; Hristov, Dimitre H

2014-08-01

In this study, the authors introduce and demonstrate quality control procedures for evaluating the geometric and dosimetric fidelity of dynamic treatment delivery techniques involving treatment couch motion synchronous with gantry and multileaf collimator (MLC). Tests were designed to evaluate positional accuracy, velocity constancy and accuracy for dynamic couch motion under a realistic weight load. A test evaluating the geometric accuracy of the system in delivering treatments over complex dynamic trajectories was also devised. Custom XML scripts that control the Varian TrueBeam™ STx (Serial #3) axes in Developer Mode were written to implement the delivery sequences for the tests. Delivered dose patterns were captured with radiographic film or the electronic portal imaging device. The couch translational accuracy in dynamic treatment mode was 0.01 cm. Rotational accuracy was within 0.3°, with 0.04 cm displacement of the rotational axis. Dose intensity profiles capturing the velocity constancy and accuracy for translations and rotation exhibited standard deviation and maximum deviations below 3%. For complex delivery involving MLC and couch motions, the overall translational accuracy for reproducing programmed patterns was within 0.06 cm. The authors conclude that in Developer Mode, TrueBeam™ is capable of delivering dynamic treatment delivery techniques involving couch motion with good geometric and dosimetric fidelity.

DEVELOPMENT OF AGENTS AND PROCEDURES FOR DECONTAMINATION OF THE YANKEE REACTOR PRIMARY COOLANT SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watkins, R.M.

1959-03-01

Developments relative to decontamination achieved under the Yankee Reasearch and Development program are reported. The decontamination of a large test loop which had been used to conduct corrosion rate studies for the Yankee reactor program is described. The basic permanganate-citrate decontamination procedure suggested for application in Yankee reactor primary system cleanup was used. A study of the chemistry of this decontamination operation is presented, together with conclusions pertaining to the effectiveness of the solutions under the conditions studied. In an attempt to further improve the efficiency of the procedure, an additional series of static and dynamic tests was performcd usingmore » contaminated sections of stainless steel tubing from the original SlW steam generator. Survival variables in the process (reagent composition, contact time, temperature, and flow velocity) were studied. The changes in decontamination efficiency produced by these variations are discussed and compared with results obtained throughthe use of similar procedures. Based on the observations made, conclusions are drawn concerning the optimum conditions for this cleanup process, a new set of suggested basic permanganate-citrate decontamination instructions is presented, and recommendations are made concerning future studies involving this procedure. (auth)« less

Virtual Reality Hysteroscopy

PubMed

Levy

1996-08-01

New interactive computer technologies are having a significant influence on medical education, training, and practice. The newest innovation in computer technology, virtual reality, allows an individual to be immersed in a dynamic computer-generated, three-dimensional environment and can provide realistic simulations of surgical procedures. A new virtual reality hysteroscope passes through a sensing device that synchronizes movements with a three-dimensional model of a uterus. Force feedback is incorporated into this model, so the user actually experiences the collision of an instrument against the uterine wall or the sensation of the resistance or drag of a resectoscope as it cuts through a myoma in a virtual environment. A variety of intrauterine pathologies and procedures are simulated, including hyperplasia, cancer, resection of a uterine septum, polyp, or myoma, and endometrial ablation. This technology will be incorporated into comprehensive training programs that will objectively assess hand-eye coordination and procedural skills. It is possible that by incorporating virtual reality into hysteroscopic training programs, a decrease in the learning curve and the number of complications presently associated with the procedures may be realized. Prospective studies are required to assess these potential benefits.

From Theory to Air Force Practice: Applications and Non-Binary Extensions of Probabilistic Model-Building Genetic Algorithms

DTIC Science & Technology

2006-05-31

dynamics (MD) and kinetic Monte Carlo ( KMC ) procedures. In 2D surface modeling our calculations project speedups of 9 orders of magnitude at 300 degrees...programming is used to perform customized statistical mechanics by bridging the different time scales of MD and KMC quickly and well. Speedups in

Simulation gravity modeling to spacecraft-tracking data - Analysis and application

NASA Technical Reports Server (NTRS)

Phillips, R. J.; Sjogren, W. L.; Abbott, E. A.; Zisk, S. H.

1978-01-01

It is proposed that line-of-sight gravity measurements derived from spacecraft-tracking data can be used for quantitative subsurface density modeling by suitable orbit simulation procedures. Such an approach avoids complex dynamic reductions and is analogous to the modeling of conventional surface gravity data. This procedure utilizes the vector calculations of a given gravity model in a simplified trajectory integration program that simulates the line-of-sight gravity. Solutions from an orbit simulation inversion and a dynamic inversion on Doppler observables compare well (within 1% in mass and size), and the error sources in the simulation approximation are shown to be quite small. An application of this technique is made to lunar crater gravity anomalies by simulating the complete Bouguer correction to several large young lunar craters. It is shown that the craters all have negative Bouguer anomalies.

Managing complex processing of medical image sequences by program supervision techniques

NASA Astrophysics Data System (ADS)

Crubezy, Monica; Aubry, Florent; Moisan, Sabine; Chameroy, Virginie; Thonnat, Monique; Di Paola, Robert

1997-05-01

Our objective is to offer clinicians wider access to evolving medical image processing (MIP) techniques, crucial to improve assessment and quantification of physiological processes, but difficult to handle for non-specialists in MIP. Based on artificial intelligence techniques, our approach consists in the development of a knowledge-based program supervision system, automating the management of MIP libraries. It comprises a library of programs, a knowledge base capturing the expertise about programs and data and a supervision engine. It selects, organizes and executes the appropriate MIP programs given a goal to achieve and a data set, with dynamic feedback based on the results obtained. It also advises users in the development of new procedures chaining MIP programs.. We have experimented the approach for an application of factor analysis of medical image sequences as a means of predicting the response of osteosarcoma to chemotherapy, with both MRI and NM dynamic image sequences. As a result our program supervision system frees clinical end-users from performing tasks outside their competence, permitting them to concentrate on clinical issues. Therefore our approach enables a better exploitation of possibilities offered by MIP and higher quality results, both in terms of robustness and reliability.

Comparison between instrumented precracked Charpy and compact specimen tests of carbon steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nanstad, R.K.

1980-01-01

The General Atomic Company High Temperature Gas-Cooled Reactor (HTGR) is housed within a prestressed concrete reactor vessel (PCRV). Various carbon steel structural members serve as closures at penetrations in the vessel. A program of testing and evaluation is underway to determine the need for reference fracture toughness (K/sub IR/) and indexing procedures for these materials as described in Appendix G to Section III, ASME Code for light water reactor steels. The materials of interest are carbon steel forgings (SA508, Class 1) and plates (SA537, Classes 1 and 2) as well as weldments of these steels. The fracture toughness behavior ismore » characterized with instrumented precracked Charpy V-votch specimens (PCVN) - slow-bend and dynamic - and compact specimens (10-mm and 25-mm thicknesses) using both linear elastic (ASTM E399) and elastic-plastic (equivalent Energy and J-Integral) analytical procedures. For the dynamic PCVN tests, force-time traces are analyzed according to the procedures of the Pressure Vessel Research Council (PVRC)/Metal Properties Council (MPC). Testing and analytical procedures are discussed and PCVN results are compared to those obtained with compact specimens.« less

Optimum Design of High-Speed Prop-Rotors

NASA Technical Reports Server (NTRS)

Chattopadhyay, Aditi; McCarthy, Thomas Robert

1993-01-01

An integrated multidisciplinary optimization procedure is developed for application to rotary wing aircraft design. The necessary disciplines such as dynamics, aerodynamics, aeroelasticity, and structures are coupled within a closed-loop optimization process. The procedure developed is applied to address two different problems. The first problem considers the optimization of a helicopter rotor blade and the second problem addresses the optimum design of a high-speed tilting proprotor. In the helicopter blade problem, the objective is to reduce the critical vibratory shear forces and moments at the blade root, without degrading rotor aerodynamic performance and aeroelastic stability. In the case of the high-speed proprotor, the goal is to maximize the propulsive efficiency in high-speed cruise without deteriorating the aeroelastic stability in cruise and the aerodynamic performance in hover. The problems studied involve multiple design objectives; therefore, the optimization problems are formulated using multiobjective design procedures. A comprehensive helicopter analysis code is used for the rotary wing aerodynamic, dynamic and aeroelastic stability analyses and an algorithm developed specifically for these purposes is used for the structural analysis. A nonlinear programming technique coupled with an approximate analysis procedure is used to perform the optimization. The optimum blade designs obtained in each case are compared to corresponding reference designs.

Computer Based Procedures for Field Workers - FY16 Research Activities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxstrand, Johanna; Bly, Aaron

The Computer-Based Procedure (CBP) research effort is a part of the Light-Water Reactor Sustainability (LWRS) Program, which provides the technical foundations for licensing and managing the long-term, safe, and economical operation of current nuclear power plants. One of the primary missions of the LWRS program is to help the U.S. nuclear industry adopt new technologies and engineering solutions that facilitate the continued safe operation of the plants and extension of the current operating licenses. One area that could yield tremendous savings in increased efficiency and safety is in improving procedure use. A CBP provides the opportunity to incorporate context-driven jobmore » aids, such as drawings, photos, and just-in-time training. The presentation of information in CBPs can be much more flexible and tailored to the task, actual plant condition, and operation mode. The dynamic presentation of the procedure will guide the user down the path of relevant steps, thus minimizing time spent by the field worker to evaluate plant conditions and decisions related to the applicability of each step. This dynamic presentation of the procedure also minimizes the risk of conducting steps out of order and/or incorrectly assessed applicability of steps. This report provides a summary of the main research activities conducted in the Computer-Based Procedures for Field Workers effort since 2012. The main focus of the report is on the research activities conducted in fiscal year 2016. The activities discussed are the Nuclear Electronic Work Packages – Enterprise Requirements initiative, the development of a design guidance for CBPs (which compiles all insights gained through the years of CBP research), the facilitation of vendor studies at the Idaho National Laboratory (INL) Advanced Test Reactor (ATR), a pilot study for how to enhance the plant design modification work process, the collection of feedback from a field evaluation study at Plant Vogtle, and path forward to commercialize INL’s CBP system.« less

Dynamic Temperature and Pressure Measurements in the Core of a Propulsion Engine

NASA Technical Reports Server (NTRS)

Schuster, Bill; Gordon, Grant; Hultgren, Lennart S.

2015-01-01

Dynamic temperature and pressure measurements were made in the core of a TECH977 propulsion engine as part of a NASA funded investigation into indirect combustion noise. Dynamic temperature measurements were made in the combustor, the inter-turbine duct, and the mixer using ten two-wire thermocouple probes. Internal dynamic pressure measurements were made at the same locations using piezoresistive transducers installed in semi-infinite coils. Measurements were acquired at four steady state operating conditions covering the range of aircraft approach power settings. Fluctuating gas temperature spectra were computed from the thermocouple probe voltage measurements using a compensation procedure that was developed under previous NASA test programs. A database of simultaneously acquired dynamic temperature and dynamic pressure measurements was produced. Spectral and cross-spectral analyses were conducted to explore the characteristics of the temperature and pressure fluctuations inside the engine, with a particular focus on attempting to identify the presence of indirect combustion noise.

Symbolic generation of elastic rotor blade equations using a FORTRAN processor and numerical study on dynamic inflow effects on the stability of helicopter rotors

NASA Technical Reports Server (NTRS)

Reddy, T. S. R.

1986-01-01

The process of performing an automated stability analysis for an elastic-bladed helicopter rotor is discussed. A symbolic manipulation program, written in FORTRAN, is used to aid in the derivation of the governing equations of motion for the rotor. The blades undergo coupled bending and torsional deformations. Two-dimensional quasi-steady aerodynamics below stall are used. Although reversed flow effects are neglected, unsteady effects, modeled as dynamic inflow are included. Using a Lagrangian approach, the governing equations are derived in generalized coordinates using the symbolic program. The program generates the steady and perturbed equations and writes into subroutines to be called by numerical routines. The symbolic program can operate on both expressions and matrices. For the case of hovering flight, the blade and dynamic inflow equations are converted to equations in a multiblade coordinate system by rearranging the coefficients of the equations. For the case of forward flight, the multiblade equations are obtained through the symbolic program. The final multiblade equations are capable of accommodating any number of elastic blade modes. The computer implementation of this procedure consists of three stages: (1) the symbolic derivation of equations; (2) the coding of the equations into subroutines; and (3) the numerical study after identifying mass, damping, and stiffness coefficients. Damping results are presented in hover and in forward flight with and without dynamic inflow effects for various rotor blade models, including rigid blade lag-flap, elastic flap-lag, flap-lag-torsion, and quasi-static torsion. Results from dynamic inflow effects which are obtained from a lift deficiency function for a quasi-static inflow model in hover are also presented.

Staggered solution procedures for multibody dynamics simulation

NASA Technical Reports Server (NTRS)

Park, K. C.; Chiou, J. C.; Downer, J. D.

1990-01-01

The numerical solution procedure for multibody dynamics (MBD) systems is termed a staggered MBD solution procedure that solves the generalized coordinates in a separate module from that for the constraint force. This requires a reformulation of the constraint conditions so that the constraint forces can also be integrated in time. A major advantage of such a partitioned solution procedure is that additional analysis capabilities such as active controller and design optimization modules can be easily interfaced without embedding them into a monolithic program. After introducing the basic equations of motion for MBD system in the second section, Section 3 briefly reviews some constraint handling techniques and introduces the staggered stabilized technique for the solution of the constraint forces as independent variables. The numerical direct time integration of the equations of motion is described in Section 4. As accurate damping treatment is important for the dynamics of space structures, we have employed the central difference method and the mid-point form of the trapezoidal rule since they engender no numerical damping. This is in contrast to the current practice in dynamic simulations of ground vehicles by employing a set of backward difference formulas. First, the equations of motion are partitioned according to the translational and the rotational coordinates. This sets the stage for an efficient treatment of the rotational motions via the singularity-free Euler parameters. The resulting partitioned equations of motion are then integrated via a two-stage explicit stabilized algorithm for updating both the translational coordinates and angular velocities. Once the angular velocities are obtained, the angular orientations are updated via the mid-point implicit formula employing the Euler parameters. When the two algorithms, namely, the two-stage explicit algorithm for the generalized coordinates and the implicit staggered procedure for the constraint Lagrange multipliers, are brought together in a staggered manner, they constitute a staggered explicit-implicit procedure which is summarized in Section 5. Section 6 presents some example problems and discussions concerning several salient features of the staggered MBD solution procedure are offered in Section 7.

METAGUI. A VMD interface for analyzing metadynamics and molecular dynamics simulations

NASA Astrophysics Data System (ADS)

Biarnés, Xevi; Pietrucci, Fabio; Marinelli, Fabrizio; Laio, Alessandro

2012-01-01

We present a new computational tool, METAGUI, which extends the VMD program with a graphical user interface that allows constructing a thermodynamic and kinetic model of a given process simulated by large-scale molecular dynamics. The tool is specially designed for analyzing metadynamics based simulations. The huge amount of diverse structures generated during such a simulation is partitioned into a set of microstates (i.e. structures with similar values of the collective variables). Their relative free energies are then computed by a weighted-histogram procedure and the most relevant free energy wells are identified by diagonalization of the rate matrix followed by a commitor analysis. All this procedure leads to a convenient representation of the metastable states and long-time kinetics of the system which can be compared with experimental data. The tool allows to seamlessly switch between a collective variables space representation of microstates and their atomic structure representation, which greatly facilitates the set-up and analysis of molecular dynamics simulations. METAGUI is based on the output format of the PLUMED plugin, making it compatible with a number of different molecular dynamics packages like AMBER, NAMD, GROMACS and several others. The METAGUI source files can be downloaded from the PLUMED web site ( http://www.plumed-code.org). Program summaryProgram title: METAGUI Catalogue identifier: AEKH_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEKH_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: GNU General Public License version 3 No. of lines in distributed program, including test data, etc.: 117 545 No. of bytes in distributed program, including test data, etc.: 8 516 203 Distribution format: tar.gz Programming language: TK/TCL, Fortran Computer: Any computer with a VMD installation and capable of running an executable produced by a gfortran compiler Operating system: Linux, Unix OS-es RAM: 1 073 741 824 bytes Classification: 23 External routines: A VMD installation ( http://www.ks.uiuc.edu/Research/vmd/) Nature of problem: Extract thermodynamic data and build a kinetic model of a given process simulated by metadynamics or molecular dynamics simulations, and provide this information on a dual representation that allows navigating and exploring the molecular structures corresponding to each point along the multi-dimensional free energy hypersurface. Solution method: Graphical-user interface linked to VMD that clusterizes the simulation trajectories in the space of a set of collective variables and assigns each frame to a given microstate, determines the free energy of each microstate by a weighted histogram analysis method, and identifies the most relevant free energy wells (kinetic basins) by diagonalization of the rate matrix followed by a commitor analysis. Restrictions: Input format files compatible with PLUMED and all the MD engines supported by PLUMED and VMD. Running time: A few minutes.

Development and Maintenance of Choice in a Dynamic Environment

ERIC Educational Resources Information Center

Rodewald, Andrew M.; Hughes, Christine E.; Pitts, Raymond C.

2010-01-01

Four pigeons were exposed to a concurrent procedure similar to that used by Davison, Baum, and colleagues (e.g., Davison & Baum, 2000, 2006) in which seven components were arranged in a mixed schedule, and each programmed a different left:right reinforcer ratio (1:27, 1:9, 1:3, 1:1, 3:1, 9:1, 27:1). Components within each session were presented…

Preliminary Report: An Application of the Good Behavior Game in the Developing Nation of Belize

ERIC Educational Resources Information Center

Nolan, Julene D.; Filter, Kevin J.; Houlihan, Daniel

2014-01-01

Educating children on a global level is a dynamic process where policy, procedure and guideline changes can leave teachers searching for new programs to resolve new challenges. This brief report shows a successful application of the Good Behavior Game in a school in the country of Belize following a significant change in policy regarding…

NASA/FAA general aviation crash dynamics program

NASA Technical Reports Server (NTRS)

Thomson, R. G.; Hayduk, R. J.; Carden, H. D.

1981-01-01

The program involves controlled full scale crash testing, nonlinear structural analyses to predict large deflection elastoplastic response, and load attenuating concepts for use in improved seat and subfloor structure. Both analytical and experimental methods are used to develop expertise in these areas. Analyses include simplified procedures for estimating energy dissipating capabilities and comprehensive computerized procedures for predicting airframe response. These analyses are developed to provide designers with methods for predicting accelerations, loads, and displacements on collapsing structure. Tests on typical full scale aircraft and on full and subscale structural components are performed to verify the analyses and to demonstrate load attenuating concepts. A special apparatus was built to test emergency locator transmitters when attached to representative aircraft structure. The apparatus is shown to provide a good simulation of the longitudinal crash pulse observed in full scale aircraft crash tests.

CAN-DO, CFD-based Aerodynamic Nozzle Design and Optimization program for supersonic/hypersonic wind tunnels

NASA Technical Reports Server (NTRS)

Korte, John J.; Kumar, Ajay; Singh, D. J.; White, J. A.

1992-01-01

A design program is developed which incorporates a modern approach to the design of supersonic/hypersonic wind-tunnel nozzles. The approach is obtained by the coupling of computational fluid dynamics (CFD) with design optimization. The program can be used to design a 2D or axisymmetric, supersonic or hypersonic, wind-tunnel nozzles that can be modeled with a calorically perfect gas. The nozzle design is obtained by solving a nonlinear least-squares optimization problem (LSOP). The LSOP is solved using an iterative procedure which requires intermediate flowfield solutions. The nozzle flowfield is simulated by solving the Navier-Stokes equations for the subsonic and transonic flow regions and the parabolized Navier-Stokes equations for the supersonic flow regions. The advantages of this method are that the design is based on the solution of the viscous equations eliminating the need to make separate corrections to a design contour, and the flexibility of applying the procedure to different types of nozzle design problems.

A data base and analysis program for shuttle main engine dynamic pressure measurements

NASA Technical Reports Server (NTRS)

Coffin, T.

1986-01-01

A dynamic pressure data base management system is described for measurements obtained from space shuttle main engine (SSME) hot firing tests. The data were provided in terms of engine power level and rms pressure time histories, and power spectra of the dynamic pressure measurements at selected times during each test. Test measurements and engine locations are defined along with a discussion of data acquisition and reduction procedures. A description of the data base management analysis system is provided and subroutines developed for obtaining selected measurement means, variances, ranges and other statistics of interest are discussed. A summary of pressure spectra obtained at SSME rated power level is provided for reference. Application of the singular value decomposition technique to spectrum interpolation is discussed and isoplots of interpolated spectra are presented to indicate measurement trends with engine power level. Program listings of the data base management and spectrum interpolation software are given. Appendices are included to document all data base measurements.

Dynamic variational asymptotic procedure for laminated composite shells

NASA Astrophysics Data System (ADS)

Lee, Chang-Yong

Unlike published shell theories, the main two parts of this thesis are devoted to the asymptotic construction of a refined theory for composite laminated shells valid over a wide range of frequencies and wavelengths. The resulting theory is applicable to shells each layer of which is made of materials with monoclinic symmetry. It enables one to analyze shell dynamic responses within both long-wavelength, low- and high-frequency vibration regimes. It also leads to energy functionals that are both positive definiteness and sufficient simplicity for all wavelengths. This whole procedure was first performed analytically. From the insight gained from the procedure, a finite element version of the analysis was then developed; and a corresponding computer program, DVAPAS, was developed. DVAPAS can obtain the generalized 2-D constitutive law and recover accurately the 3-D results for stress and strain in composite shells. Some independent works will be needed to develop the corresponding 2-D surface analysis associated with the present theory and to continue towards full verification and validation of the present process by comparison with available published works.

Hierarchic Extensions in the Static and Dynamic Analysis of Elastic Beams. Ph.D. Thesis, 1990 Final Report, May 1990

NASA Technical Reports Server (NTRS)

Watson, Robert A.

1991-01-01

Approximate solutions of static and dynamic beam problems by the p-version of the finite element method are investigated. Within a hierarchy of engineering beam idealizations, rigorous formulations of the strain and kinetic energies for straight and circular beam elements are presented. These formulations include rotating coordinate system effects and geometric nonlinearities to allow for the evaluation of vertical axis wind turbines, the motivating problem for this research. Hierarchic finite element spaces, based on extensions of the polynomial orders used to approximate the displacement variables, are constructed. The developed models are implemented into a general purpose computer program for evaluation. Quality control procedures are examined for a diverse set of sample problems. These procedures include estimating discretization errors in energy norm and natural frequencies, performing static and dynamic equilibrium checks, observing convergence for qualities of interest, and comparison with more exacting theories and experimental data. It is demonstrated that p-extensions produce exponential rates of convergence in the approximation of strain energy and natural frequencies for the class of problems investigated.

Ground test program for a full-size solar dynamic heat receiver

NASA Technical Reports Server (NTRS)

Sedgwick, L. M.; Kaufmann, K. J.; Mclallin, K. L.; Kerslake, T. W.

1991-01-01

Test hardware, facilities, and procedures were developed to conduct ground testing of a full-size, solar dynamic heat receiver in a partially simulated, low earth orbit environment. The heat receiver was designed to supply 102 kW of thermal energy to a helium and xenon gas mixture continuously over a 94 minute orbit, including up to 36 minutes of eclipse. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber using liquid nitrogen cold shrouds and an aperture cold plate. Special test equipment was designed to provide the required ranges in interface boundary conditions that typify those expected or required for operation as part of the solar dynamic power module on the Space Station Freedom. The support hardware includes an infrared quartz lamp heater with 30 independently controllable zones and a closed-Brayton cycle engine simulator to circulate and condition the helium-xenon gas mixture. The test article, test support hardware, facilities, and instrumentation developed to conduct the ground test program are all described.

Ground test program for a full-size solar dynamic heat receiver

NASA Technical Reports Server (NTRS)

Sedgwick, L. M.; Kaufmann, K. J.; Mclallin, K. L.; Kerslake, T. W.

1991-01-01

Test hardware, facilities, and procedures were developed to conduct ground testing of a full size, solar dynamic heat receiver in a partially simulated, low Earth orbit environment. The heat receiver was designed to supply 102 kW of thermal energy to a helium and xenon gas mixture continuously over a 94 minute orbit, including up to 36 minutes of eclipse. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber using liquid nitrogen cold shrouds and an aperture cold plate. Special test equipment were designed to provide the required ranges in interface boundary conditions that typify those expected or required for operation as part of the solar dynamic power module on the Space Station Freedom. The support hardware includes an infrared quartz lamp heater with 30 independently controllable zones and a closed Brayton cycle engine simulator to circulate and condition the helium xenon gas mixture. The test article, test support hardware, facilities, and instrumentation developed to conduct the ground test program are all described.

Ground test program for a full-size solar dynamic heat receiver

NASA Astrophysics Data System (ADS)

Sedgwick, L. M.; Kaufmann, K. J.; McLallin, K. L.; Kerslake, T. W.

Test hardware, facilities, and procedures were developed to conduct ground testing of a full-size, solar dynamic heat receiver in a partially simulated, low earth orbit environment. The heat receiver was designed to supply 102 kW of thermal energy to a helium and xenon gas mixture continuously over a 94 minute orbit, including up to 36 minutes of eclipse. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber using liquid nitrogen cold shrouds and an aperture cold plate. Special test equipment was designed to provide the required ranges in interface boundary conditions that typify those expected or required for operation as part of the solar dynamic power module on the Space Station Freedom. The support hardware includes an infrared quartz lamp heater with 30 independently controllable zones and a closed-Brayton cycle engine simulator to circulate and condition the helium-xenon gas mixture. The test article, test support hardware, facilities, and instrumentation developed to conduct the ground test program are all described.

Weather and Climate Monitoring Protocol, Channel Islands National Park, California

USGS Publications Warehouse

McEachern, Kathryn; Power, Paula; Dye, Linda; Rudolph, Rocky

2008-01-01

Weather and climate are strong drivers of population dynamics, plant and animal spatial distributions, community interactions, and ecosystem states. Information on local weather and climate is crucial in interpreting trends and patterns in the natural environment for resource management, research, and visitor enjoyment. This document describes the weather and climate monitoring program at the Channel Islands National Park (fig. 1), initiated in the 1990s. Manual and automated stations, which continue to evolve as technology changes, are being used for this program. The document reviews the history of weather data collection on each of the five Channel Islands National Park islands, presents program administrative structure, and provides an overview of procedures for data collection, archival, retrieval, and reporting. This program overview is accompanied by the 'Channel Islands National Park Remote Automated Weather Station Field Handbook' and the 'Channel Islands National Park Ranger Weather Station Field Handbook'. These Handbooks are maintained separately at the Channel Island National Park as 'live documents' that are updated as needed to provide a current working manual of weather and climate monitoring procedures. They are available on request from the Weather Program Manager (Channel Islands National Park, 1901 Spinnaker Dr., Ventura, CA 93001; 805.658.5700). The two Field Handbooks describe in detail protocols for managing the four remote automated weather stations (RAWS) and the seven manual Ranger Weather Stations on the islands, including standard operating procedures for equipment maintenance and calibration; manufacturer operating manuals; data retrieval and archiving; metada collection and archival; and local, agency, and vendor contracts.

Three-Dimensional Road Network by Fusion of Polarimetric and Interferometric SAR Data

NASA Technical Reports Server (NTRS)

Gamba, P.; Houshmand, B.

1998-01-01

In this paper a fuzzy classification procedure is applied to polarimetric radar measurements, and street pixels are detected. These data are successively grouped into consistent roads by means of a dynamic programming approach based on the fuzzy membership function values. Further fusion of the 2D road network extracted and 3D TOPSAR measurements provides a powerful way to analyze urban infrastructures.

Building the Joint Battlespace Infosphere. Volume 1: Summary

DTIC Science & Technology

1999-12-17

Integrity guarantees. The information staff will conduct audits and other routine procedures to ensure that the JBI platform and its clients are...delete the object; thereafter, the object will not be available to other JBI clients, but it will have been saved in an archive for auditing or...this project are maintaining multiyear, multilocation programs in nomadic networking and assuring quality of service in emerging networks. Dynamic

Experiences at Langley Research Center in the application of optimization techniques to helicopter airframes for vibration reduction

NASA Technical Reports Server (NTRS)

Murthy, T. Sreekanta; Kvaternik, Raymond G.

1991-01-01

A NASA/industry rotorcraft structural dynamics program known as Design Analysis Methods for VIBrationS (DAMVIBS) was initiated at Langley Research Center in 1984 with the objective of establishing the technology base needed by the industry for developing an advanced finite-element-based vibrations design analysis capability for airframe structures. As a part of the in-house activities contributing to that program, a study was undertaken to investigate the use of formal, nonlinear programming-based, numerical optimization techniques for airframe vibrations design work. Considerable progress has been made in connection with that study since its inception in 1985. This paper presents a unified summary of the experiences and results of that study. The formulation and solution of airframe optimization problems are discussed. Particular attention is given to describing the implementation of a new computational procedure based on MSC/NASTRAN and CONstrained function MINimization (CONMIN) in a computer program system called DYNOPT for the optimization of airframes subject to strength, frequency, dynamic response, and fatigue constraints. The results from the application of the DYNOPT program to the Bell AH-1G helicopter are presented and discussed.

Integrated aerodynamic/dynamic optimization of helicopter rotor blades

NASA Technical Reports Server (NTRS)

Chattopadhyay, Aditi; Walsh, Joanne L.; Riley, Michael F.

1989-01-01

An integrated aerodynamic/dynamic optimization procedure is used to minimize blade weight and 4 per rev vertical hub shear for a rotor blade in forward flight. The coupling of aerodynamics and dynamics is accomplished through the inclusion of airloads which vary with the design variables during the optimization process. Both single and multiple objective functions are used in the optimization formulation. The Global Criteria Approach is used to formulate the multiple objective optimization and results are compared with those obtained by using single objective function formulations. Constraints are imposed on natural frequencies, autorotational inertia, and centrifugal stress. The program CAMRAD is used for the blade aerodynamic and dynamic analyses, and the program CONMIN is used for the optimization. Since the spanwise and the azimuthal variations of loading are responsible for most rotor vibration and noise, the vertical airload distributions on the blade, before and after optimization, are compared. The total power required by the rotor to produce the same amount of thrust for a given area is also calculated before and after optimization. Results indicate that integrated optimization can significantly reduce the blade weight, the hub shear and the amplitude of the vertical airload distributions on the blade and the total power required by the rotor.

Combinatorial approaches to gene recognition.

PubMed

Roytberg, M A; Astakhova, T V; Gelfand, M S

1997-01-01

Recognition of genes via exon assembly approaches leads naturally to the use of dynamic programming. We consider the general graph-theoretical formulation of the exon assembly problem and analyze in detail some specific variants: multicriterial optimization in the case of non-linear gene-scoring functions; context-dependent schemes for scoring exons and related procedures for exon filtering; and highly specific recognition of arbitrary gene segments, oligonucleotide probes and polymerase chain reaction (PCR) primers.

A stochastic regulator for integrated communication and control systems. I - Formulation of control law. II - Numerical analysis and simulation

NASA Technical Reports Server (NTRS)

Liou, Luen-Woei; Ray, Asok

1991-01-01

A state feedback control law for integrated communication and control systems (ICCS) is formulated by using the dynamic programming and optimality principle on a finite-time horizon. The control law is derived on the basis of a stochastic model of the plant which is augmented in state space to allow for the effects of randomly varying delays in the feedback loop. A numerical procedure for synthesizing the control parameters is then presented, and the performance of the control law is evaluated by simulating the flight dynamics model of an advanced aircraft. Finally, recommendations for future work are made.

Study of Dynamic Characteristics of Aeroelastic Systems Utilizing Randomdec Signatures

NASA Technical Reports Server (NTRS)

Chang, C. S.

1975-01-01

The feasibility of utilizing the random decrement method in conjunction with a signature analysis procedure to determine the dynamic characteristics of an aeroelastic system for the purpose of on-line prediction of potential on-set of flutter was examined. Digital computer programs were developed to simulate sampled response signals of a two-mode aeroelastic system. Simulated response data were used to test the random decrement method. A special curve-fit approach was developed for analyzing the resulting signatures. A number of numerical 'experiments' were conducted on the combined processes. The method is capable of determining frequency and damping values accurately from randomdec signatures of carefully selected lengths.

Selected options supporting use of the group embedded figures test in modeling achievement in clinical laboratory science programs.

PubMed

Powell, M E

1995-01-01

To identify, in light of predicted future shortages of allied-health personnel, student and curricular characteristics of clinical laboratory science (CLS) programs relevant to recruitment and retention at the baccalaureate level. Not applicable. Not applicable. Options for modeling achievement in CLS programs are developed, and designs and procedures for clarifying procedural questions are considered in a context of delivery of instruction for specialized curricula and skill development. Considerable attention is given to the potential for using the Group Embedded Figures Test (GEFT) in modeling, advising, designing curricula, and monitoring quality improvement of programs and graduates. Not applicable. Supporting evidence is supplied from the literature for options in developing an appropriate model for examining those salient variables known to have linkages to achievement. An argument is presented for better understanding of antecedent variables affecting achievement and retention of CLS students. In addition, a case is made for development of an appropriate model examining variables identified in the literature as being linked to achievement. Dynamic models based on these considerations should be developed chronologically from entry through graduation with emphasis on growth at year-end milestones.

Implications of the Turing machine model of computation for processor and programming language design

NASA Astrophysics Data System (ADS)

Hunter, Geoffrey

2004-01-01

A computational process is classified according to the theoretical model that is capable of executing it; computational processes that require a non-predeterminable amount of intermediate storage for their execution are Turing-machine (TM) processes, while those whose storage are predeterminable are Finite Automation (FA) processes. Simple processes (such as traffic light controller) are executable by Finite Automation, whereas the most general kind of computation requires a Turing Machine for its execution. This implies that a TM process must have a non-predeterminable amount of memory allocated to it at intermediate instants of its execution; i.e. dynamic memory allocation. Many processes encountered in practice are TM processes. The implication for computational practice is that the hardware (CPU) architecture and its operating system must facilitate dynamic memory allocation, and that the programming language used to specify TM processes must have statements with the semantic attribute of dynamic memory allocation, for in Alan Turing"s thesis on computation (1936) the "standard description" of a process is invariant over the most general data that the process is designed to process; i.e. the program describing the process should never have to be modified to allow for differences in the data that is to be processed in different instantiations; i.e. data-invariant programming. Any non-trivial program is partitioned into sub-programs (procedures, subroutines, functions, modules, etc). Examination of the calls/returns between the subprograms reveals that they are nodes in a tree-structure; this tree-structure is independent of the programming language used to encode (define) the process. Each sub-program typically needs some memory for its own use (to store values intermediate between its received data and its computed results); this locally required memory is not needed before the subprogram commences execution, and it is not needed after its execution terminates; it may be allocated as its execution commences, and deallocated as its execution terminates, and if the amount of this local memory is not known until just before execution commencement, then it is essential that it be allocated dynamically as the first action of its execution. This dynamically allocated/deallocated storage of each subprogram"s intermediate values, conforms with the stack discipline; i.e. last allocated = first to be deallocated, an incidental benefit of which is automatic overlaying of variables. This stack-based dynamic memory allocation was a semantic implication of the nested block structure that originated in the ALGOL-60 programming language. AGLOL-60 was a TM language, because the amount of memory allocated on subprogram (block/procedure) entry (for arrays, etc) was computable at execution time. A more general requirement of a Turing machine process is for code generation at run-time; this mandates access to the source language processor (compiler/interpretor) during execution of the process. This fundamental aspect of computer science is important to the future of system design, because it has been overlooked throughout the 55 years since modern computing began in 1048. The popular computer systems of this first half-century of computing were constrained by compile-time (or even operating system boot-time) memory allocation, and were thus limited to executing FA processes. The practical effect was that the distinction between the data-invariant program and its variable data was blurred; programmers had to make trial and error executions, modifying the program"s compile-time constants (array dimensions) to iterate towards the values required at run-time by the data being processed. This era of trial and error computing still persists; it pervades the culture of current (2003) computing practice.

Analysis of flexible aircraft longitudinal dynamics and handling qualities. Volume 2: Data

NASA Technical Reports Server (NTRS)

Waszak, M. R.; Schmidt, D. K.

1985-01-01

Two analysis methods are applied to a family of flexible aircraft in order to investigate how and when structural (especially dynamic aeroelastic) effects affect the dynamic characteristics of aircraft. The first type of analysis is an open loop modal analysis technique. This method considers the effect of modal residue magnitudes on determining vehicle handling qualities. The second method is a pilot in the loop analysis procedure that considers several closed loop system characteristics. Both analyses indicated that dynamic aeroelastic effects caused a degradation in vehicle tracking performance, based on the evaluation of some simulation results. Volume 2 consists of the presentation of the state variable models of the flexible aircraft configurations used in the analysis applications mode shape plots for the structural modes, numerical results from the modal analysis frequency response plots from the pilot in the loop analysis and a listing of the modal analysis computer program.

The modern temperature-accelerated dynamics approach

DOE PAGES

Zamora, Richard J.; Uberuaga, Blas P.; Perez, Danny; ...

2016-06-01

Accelerated molecular dynamics (AMD) is a class of MD-based methods used to simulate atomistic systems in which the metastable state-to-state evolution is slow compared with thermal vibrations. Temperature-accelerated dynamics (TAD) is a particularly efficient AMD procedure in which the predicted evolution is hastened by elevating the temperature of the system and then recovering the correct state-to-state dynamics at the temperature of interest. TAD has been used to study various materials applications, often revealing surprising behavior beyond the reach of direct MD. This success has inspired several algorithmic performance enhancements, as well as the analysis of its mathematical framework. Recently, thesemore » enhancements have leveraged parallel programming techniques to enhance both the spatial and temporal scaling of the traditional approach. Here, we review the ongoing evolution of the modern TAD method and introduce the latest development: speculatively parallel TAD.« less

Riding and handling qualities of light aircraft: A review and analysis

NASA Technical Reports Server (NTRS)

Smetana, F. O.; Summery, D. C.; Johnson, W. D.

1972-01-01

Design procedures and supporting data necessary for configuring light aircraft to obtain desired responses to pilot commands and gusts are presented. The procedures employ specializations of modern military and jet transport practice where these provide an improvement over earlier practice. General criteria for riding and handling qualities are discussed in terms of the airframe dynamics. Methods available in the literature for calculating the coefficients required for a linearized analysis of the airframe dynamics are reviewed in detail. The review also treats the relation of spin and stall to airframe geometry. Root locus analysis is used to indicate the sensitivity of airframe dynamics to variations in individual stability derivatives and to variations in geometric parameters. Computer programs are given for finding the frequencies, damping ratios, and time constants of all rigid body modes and for generating time histories of aircraft motions in response to control inputs. Appendices are included presenting the derivation of the linearized equations of motion; the stability derivatives; the transfer functions; approximate solutions for the frequency, damping ratio, and time constants; an indication of methods to be used when linear analysis is inadequate; sample calculations; and an explanation of the use of root locus diagrams and Bode plots.

Web based tools for data manipulation, visualisation and validation with interactive georeferenced graphs

NASA Astrophysics Data System (ADS)

Ivankovic, D.; Dadic, V.

2009-04-01

Some of oceanographic parameters have to be manually inserted into database; some (for example data from CTD probe) are inserted from various files. All this parameters requires visualization, validation and manipulation from research vessel or scientific institution, and also public presentation. For these purposes is developed web based system, containing dynamic sql procedures and java applets. Technology background is Oracle 10g relational database, and Oracle application server. Web interfaces are developed using PL/SQL stored database procedures (mod PL/SQL). Additional parts for data visualization include use of Java applets and JavaScript. Mapping tool is Google maps API (javascript) and as alternative java applet. Graph is realized as dynamically generated web page containing java applet. Mapping tool and graph are georeferenced. That means that click on some part of graph, automatically initiate zoom or marker onto location where parameter was measured. This feature is very useful for data validation. Code for data manipulation and visualization are partially realized with dynamic SQL and that allow as to separate data definition and code for data manipulation. Adding new parameter in system requires only data definition and description without programming interface for this kind of data.

Design of a flexure mount for optics in dynamic and cryogenic environments

NASA Technical Reports Server (NTRS)

Pollard, Lloyd Wayne

1989-01-01

The design of a flexure mount for a mirror operating in a cryogenic environment is presented. This structure represents a design effort recently submitted to NASA Ames for the support of the primary mirror of the Space Infrared Telescope Facility (SIRTF). The support structure must passively accommodate the differential thermal contraction between the glass mirror and the aluminium structure of the telescope during cryogenic cooldown. Further, it must support the one meter diameter, 116 kilogram (258 pound) primary mirror during a severe launch to orbit without exceeding the micro-yield of the material anywhere in the flexure mount. Procedures used to establish the maximum allowable radial stiffness of the flexural mount, based on the finite element program NASTRAN and the optical program FRINGE, are discussed. Early design concepts were evaluated using a parametric design program, and the development of that program is presented. Dynamic loading analyses performed with NASTRAN are discussed. Methods of combining modal responses resulting from a displacement response spectrum analysis are discussed, and a combination scheme called MRSS, modified root of sum of squares, is presented. Model combination schemes using MRSS, SRSS, and ABS are compared to the results of the modal frequency response analysis performed with NASTRAN.

The integrated manual and automatic control of complex flight systems

NASA Technical Reports Server (NTRS)

Schmidt, D. K.

1986-01-01

The topics of research in this program include pilot/vehicle analysis techniques, identification of pilot dynamics, and control and display synthesis techniques for optimizing aircraft handling qualities. The project activities are discussed. The current technical activity is directed at extending and validating the active display synthesis procedure, and the pilot/vehicle analysis of the NLR rate-command flight configurations in the landing task. Two papers published by the researchers are attached as appendices.

Fully integrated aerodynamic/dynamic optimization of helicopter rotor blades

NASA Technical Reports Server (NTRS)

Walsh, Joanne L.; Lamarsh, William J., II; Adelman, Howard M.

1992-01-01

This paper describes a fully integrated aerodynamic/dynamic optimization procedure for helicopter rotor blades. The procedure combines performance and dynamics analyses with a general purpose optimizer. The procedure minimizes a linear combination of power required (in hover, forward flight, and maneuver) and vibratory hub shear. The design variables include pretwist, taper initiation, taper ratio, root chord, blade stiffnesses, tuning masses, and tuning mass locations. Aerodynamic constraints consist of limits on power required in hover, forward flight and maneuver; airfoil section stall; drag divergence Mach number; minimum tip chord; and trim. Dynamic constraints are on frequencies, minimum autorotational inertia, and maximum blade weight. The procedure is demonstrated for two cases. In the first case the objective function involves power required (in hover, forward flight, and maneuver) and dynamics. The second case involves only hover power and dynamics. The designs from the integrated procedure are compared with designs from a sequential optimization approach in which the blade is first optimized for performance and then for dynamics. In both cases, the integrated approach is superior.

Fully integrated aerodynamic/dynamic optimization of helicopter rotor blades

NASA Technical Reports Server (NTRS)

Walsh, Joanne L.; Lamarsh, William J., II; Adelman, Howard M.

1992-01-01

A fully integrated aerodynamic/dynamic optimization procedure is described for helicopter rotor blades. The procedure combines performance and dynamic analyses with a general purpose optimizer. The procedure minimizes a linear combination of power required (in hover, forward flight, and maneuver) and vibratory hub shear. The design variables include pretwist, taper initiation, taper ratio, root chord, blade stiffnesses, tuning masses, and tuning mass locations. Aerodynamic constraints consist of limits on power required in hover, forward flight and maneuvers; airfoil section stall; drag divergence Mach number; minimum tip chord; and trim. Dynamic constraints are on frequencies, minimum autorotational inertia, and maximum blade weight. The procedure is demonstrated for two cases. In the first case, the objective function involves power required (in hover, forward flight and maneuver) and dynamics. The second case involves only hover power and dynamics. The designs from the integrated procedure are compared with designs from a sequential optimization approach in which the blade is first optimized for performance and then for dynamics. In both cases, the integrated approach is superior.

Interdisciplinary analysis procedures in the modeling and control of large space-based structures

NASA Technical Reports Server (NTRS)

Cooper, Paul A.; Stockwell, Alan E.; Kim, Zeen C.

1987-01-01

The paper describes a computer software system called the Integrated Multidisciplinary Analysis Tool, IMAT, that has been developed at NASA Langley Research Center. IMAT provides researchers and analysts with an efficient capability to analyze satellite control systems influenced by structural dynamics. Using a menu-driven interactive executive program, IMAT links a relational database to commercial structural and controls analysis codes. The paper describes the procedures followed to analyze a complex satellite structure and control system. The codes used to accomplish the analysis are described, and an example is provided of an application of IMAT to the analysis of a reference space station subject to a rectangular pulse loading at its docking port.

An algorithm for the solution of dynamic linear programs

NASA Technical Reports Server (NTRS)

Psiaki, Mark L.

1989-01-01

The algorithm's objective is to efficiently solve Dynamic Linear Programs (DLP) by taking advantage of their special staircase structure. This algorithm constitutes a stepping stone to an improved algorithm for solving Dynamic Quadratic Programs, which, in turn, would make the nonlinear programming method of Successive Quadratic Programs more practical for solving trajectory optimization problems. The ultimate goal is to being trajectory optimization solution speeds into the realm of real-time control. The algorithm exploits the staircase nature of the large constraint matrix of the equality-constrained DLPs encountered when solving inequality-constrained DLPs by an active set approach. A numerically-stable, staircase QL factorization of the staircase constraint matrix is carried out starting from its last rows and columns. The resulting recursion is like the time-varying Riccati equation from multi-stage LQR theory. The resulting factorization increases the efficiency of all of the typical LP solution operations over that of a dense matrix LP code. At the same time numerical stability is ensured. The algorithm also takes advantage of dynamic programming ideas about the cost-to-go by relaxing active pseudo constraints in a backwards sweeping process. This further decreases the cost per update of the LP rank-1 updating procedure, although it may result in more changes of the active set that if pseudo constraints were relaxed in a non-stagewise fashion. The usual stability of closed-loop Linear/Quadratic optimally-controlled systems, if it carries over to strictly linear cost functions, implies that the saving due to reduced factor update effort may outweigh the cost of an increased number of updates. An aerospace example is presented in which a ground-to-ground rocket's distance is maximized. This example demonstrates the applicability of this class of algorithms to aerospace guidance. It also sheds light on the efficacy of the proposed pseudo constraint relaxation scheme.

Children's feeding programs in Atlantic Canada: some Foucauldian theoretical concepts in action.

PubMed

Dayle, Jutta B; McIntyre, Lynn

2003-07-01

Since 1989 the number of Canadian children depending on food banks has increased by more than 85%. To combat perceived hunger, breakfast and lunch programs have been initiated by localized volunteer efforts. This paper attempts to show the Foucauldian concepts of power, truths, space and time in action in feeding programs in Atlantic Canada. A potential 'relation of docility-utility' is imposed upon children by providers of feeding programs and ultimately the state. The 'power over life' or 'micro-physics of power' is accomplished through procedures that use food, rules, rewards, reinforcements, space, time, and truths. Children voluntarily subject themselves to this relation while reserving the power to resist through acts of defiance or by not attending at all. This ability to exercise one's agency allows for shifting power relations in the social dynamics of feeding programs. The potentially coercive nature of these relationships is embedded in the pleasurable environment generated by the feeding process.

A real-time programming system.

PubMed

Townsend, H R

1979-03-01

The paper describes a Basic Operating and Scheduling System (BOSS) designed for a small computer. User programs are organised as self-contained modular 'processes' and the way in which the scheduler divides the time of the computer equally between them, while arranging for any process which has to respond to an interrupt from a peripheral device to be given the necessary priority, is described in detail. Next the procedures provided by the operating system to organise communication between processes are described, and how they are used to construct dynamically self-modifying real-time systems. Finally, the general philosophy of BOSS and applications to a multi-processor assembly are discussed.

Algorithmic analysis of relational learning processes in instructional technology: Some implications for basic, translational, and applied research.

PubMed

McIlvane, William J; Kledaras, Joanne B; Gerard, Christophe J; Wilde, Lorin; Smelson, David

2018-07-01

A few noteworthy exceptions notwithstanding, quantitative analyses of relational learning are most often simple descriptive measures of study outcomes. For example, studies of stimulus equivalence have made much progress using measures such as percentage consistent with equivalence relations, discrimination ratio, and response latency. Although procedures may have ad hoc variations, they remain fairly similar across studies. Comparison studies of training variables that lead to different outcomes are few. Yet to be developed are tools designed specifically for dynamic and/or parametric analyses of relational learning processes. This paper will focus on recent studies to develop (1) quality computer-based programmed instruction for supporting relational learning in children with autism spectrum disorders and intellectual disabilities and (2) formal algorithms that permit ongoing, dynamic assessment of learner performance and procedure changes to optimize instructional efficacy and efficiency. Because these algorithms have a strong basis in evidence and in theories of stimulus control, they may have utility also for basic and translational research. We present an overview of the research program, details of algorithm features, and summary results that illustrate their possible benefits. It also presents arguments that such algorithm development may encourage parametric research, help in integrating new research findings, and support in-depth quantitative analyses of stimulus control processes in relational learning. Such algorithms may also serve to model control of basic behavioral processes that is important to the design of effective programmed instruction for human learners with and without functional disabilities. Copyright © 2018 Elsevier B.V. All rights reserved.

Increasingly automated procedure acquisition in dynamic systems

NASA Technical Reports Server (NTRS)

Mathe, Nathalie; Kedar, Smadar

1992-01-01

Procedures are widely used by operators for controlling complex dynamic systems. Currently, most development of such procedures is done manually, consuming a large amount of paper, time, and manpower in the process. While automated knowledge acquisition is an active field of research, not much attention has been paid to the problem of computer-assisted acquisition and refinement of complex procedures for dynamic systems. The Procedure Acquisition for Reactive Control Assistant (PARC), which is designed to assist users in more systematically and automatically encoding and refining complex procedures. PARC is able to elicit knowledge interactively from the user during operation of the dynamic system. We categorize procedure refinement into two stages: diagnosis - diagnose the failure and choose a repair - and repair - plan and perform the repair. The basic approach taken in PARC is to assist the user in all steps of this process by providing increased levels of assistance with layered tools. We illustrate the operation of PARC in refining procedures for the control of a robot arm.

Automatic procedure for stable tetragonal or hexagonal structures: application to tetragonal Y and Cd

NASA Astrophysics Data System (ADS)

Marcus, P. M.; Jona, F.

2005-05-01

A simple effective procedure (MNP) for finding equilibrium tetragonal and hexagonal states under pressure is described and applied. The MNP procedure finds a path to minima of the Gibbs free energy G at T=0 K (G=E+pV, E=energy per atom, p=pressure, V=volume per atom) for tetragonal and hexagonal structures by using the approximate expansion of G in linear and quadratic strains at an arbitrary initial structure to find a change in the strains which moves toward a minimum of G. Iteration automatically proceeds to a minimum within preset convergence criteria on the calculation of the minimum. Comparison is made with experimental results for the ground states of seven metallic elements in hexagonal close-packed (hcp), face- and body-centered cubic structures, and with a previous procedure for finding minima based on tracing G along the epitaxial Bain path (EBP) to a minimum; the MNP is more easily generalized than the EBP procedure to lower symmetry and more atoms in the unit cell. Comparison is also made with a molecular-dynamics program for crystal equilibrium structures under pressure and with CRYSTAL, a program for crystal equilibrium structures at zero pressure. Application of MNP to the elements Y and Cd, which have hcp ground states at zero pressure, finds minima of E at face-centered cubic (fcc) structure for both Y and Cd. Evaluation of all the elastic constants shows that fcc Y is stable, hence a metastable phase, but fcc Cd is unstable.

Analysis of pilot control strategy

NASA Technical Reports Server (NTRS)

Heffley, R. K.; Hanson, G. D.; Jewell, W. F.; Clement, W. F.

1983-01-01

Methods for nonintrusive identification of pilot control strategy and task execution dynamics are presented along with examples based on flight data. The specific analysis technique is Nonintrusive Parameter Identification Procedure (NIPIP), which is described in a companion user's guide (NASA CR-170398). Quantification of pilot control strategy and task execution dynamics is discussed in general terms followed by a more detailed description of how NIPIP can be applied. The examples are based on flight data obtained from the NASA F-8 digital fly by wire airplane. These examples involve various piloting tasks and control axes as well as a demonstration of how the dynamics of the aircraft itself are identified using NIPIP. Application of NIPIP to the AFTI/F-16 flight test program is discussed. Recommendations are made for flight test applications in general and refinement of NIPIP to include interactive computer graphics.

Buffet test in the National Transonic Facility

NASA Technical Reports Server (NTRS)

Young, Clarence P., Jr.; Hergert, Dennis W.; Butler, Thomas W.; Herring, Fred M.

1992-01-01

A buffet test of a commercial transport model was accomplished in the National Transonic Facility at the NASA Langley Research Center. This aeroelastic test was unprecedented for this wind tunnel and posed a high risk to the facility. This paper presents the test results from a structural dynamics and aeroelastic response point of view and describes the activities required for the safety analysis and risk assessment. The test was conducted in the same manner as a flutter test and employed onboard dynamic instrumentation, real time dynamic data monitoring, automatic, and manual tunnel interlock systems for protecting the model. The procedures and test techniques employed for this test are expected to serve as the basis for future aeroelastic testing in the National Transonic Facility. This test program was a cooperative effort between the Boeing Commercial Airplane Company and the NASA Langley Research Center.

Identifying parameter regions for multistationarity

PubMed Central

Conradi, Carsten; Mincheva, Maya; Wiuf, Carsten

2017-01-01

Mathematical modelling has become an established tool for studying the dynamics of biological systems. Current applications range from building models that reproduce quantitative data to identifying systems with predefined qualitative features, such as switching behaviour, bistability or oscillations. Mathematically, the latter question amounts to identifying parameter values associated with a given qualitative feature. We introduce a procedure to partition the parameter space of a parameterized system of ordinary differential equations into regions for which the system has a unique or multiple equilibria. The procedure is based on the computation of the Brouwer degree, and it creates a multivariate polynomial with parameter depending coefficients. The signs of the coefficients determine parameter regions with and without multistationarity. A particular strength of the procedure is the avoidance of numerical analysis and parameter sampling. The procedure consists of a number of steps. Each of these steps might be addressed algorithmically using various computer programs and available software, or manually. We demonstrate our procedure on several models of gene transcription and cell signalling, and show that in many cases we obtain a complete partitioning of the parameter space with respect to multistationarity. PMID:28972969

An Integrated Intranet and Dynamic Database Application for the Security Manager at Naval Postgraduate School

DTIC Science & Technology

2002-09-01

Basic for Applications ( VBA ) 6.0 as macros may not be supported in 8 future versions of Access. Access 2000 offers Internet- related features for...security features from Microsoft’s SQL Server. [1] 3. System Requirements Access 2000 is a resource-intensive application as are all Office 2000...1] • Modules – Functions and procedures written in the Visual Basic for Applications ( VBA ) programming language. The capabilities of modules

Improving DoD Logistics: Perspectives from Rand Research, Volume 1,

DTIC Science & Technology

1995-01-01

strategic lift, and a more dynamic environment in which plans and priorities rapidly changed and units frequently moved. As in the previous chart...legislation, regulations, or local procedures.5 4 Many of these limits are imposed on DoD by Congress, with the explicit or implicit intent to protect DoD...propagate process improvements more widely. This chart lists elements of some of these programs. The intent is not to evaluate or to be exhaustive but to

Coupled rotor/fuselage dynamic analysis of the AH-1G helicopter and correlation with flight vibrations data

NASA Technical Reports Server (NTRS)

Corrigan, J. C.; Cronkhite, J. D.; Dompka, R. V.; Perry, K. S.; Rogers, J. P.; Sadler, S. G.

1989-01-01

Under a research program designated Design Analysis Methods for VIBrationS (DAMVIBS), existing analytical methods are used for calculating coupled rotor-fuselage vibrations of the AH-1G helicopter for correlation with flight test data from an AH-1G Operational Load Survey (OLS) test program. The analytical representation of the fuselage structure is based on a NASTRAN finite element model (FEM), which has been developed, extensively documented, and correlated with ground vibration test. One procedure that was used for predicting coupled rotor-fuselage vibrations using the advanced Rotorcraft Flight Simulation Program C81 and NASTRAN is summarized. Detailed descriptions of the analytical formulation of rotor dynamics equations, fuselage dynamic equations, coupling between the rotor and fuselage, and solutions to the total system of equations in C81 are included. Analytical predictions of hub shears for main rotor harmonics 2p, 4p, and 6p generated by C81 are used in conjunction with 2p OLS measured control loads and a 2p lateral tail rotor gearbox force, representing downwash impingement on the vertical fin, to excite the NASTRAN model. NASTRAN is then used to correlate with measured OLS flight test vibrations. Blade load comparisons predicted by C81 showed good agreement. In general, the fuselage vibration correlations show good agreement between anslysis and test in vibration response through 15 to 20 Hz.

Framework for adaptive multiscale analysis of nonhomogeneous point processes.

PubMed

Helgason, Hannes; Bartroff, Jay; Abry, Patrice

2011-01-01

We develop the methodology for hypothesis testing and model selection in nonhomogeneous Poisson processes, with an eye toward the application of modeling and variability detection in heart beat data. Modeling the process' non-constant rate function using templates of simple basis functions, we develop the generalized likelihood ratio statistic for a given template and a multiple testing scheme to model-select from a family of templates. A dynamic programming algorithm inspired by network flows is used to compute the maximum likelihood template in a multiscale manner. In a numerical example, the proposed procedure is nearly as powerful as the super-optimal procedures that know the true template size and true partition, respectively. Extensions to general history-dependent point processes is discussed.

Improving L2 Reading Comprehension through Emotionalized Dynamic Assessment Procedures.

PubMed

Abdolrezapour, Parisa

2017-06-01

The paper reports a study on an emotionally-loaded dynamic assessment procedure used with Iranian EFL learners. It focuses on the effect of using emotional intelligence characteristics (based on Goleman's framework) as a tool for motivating learners while performing reading tasks. The study with 50 intermediate learners aged 12-15 used three modalities: a control group, which was taught under institute's normal procedures; a comparison group, which received dynamic assessment (DA); and an experimental group, which received emotionalized dynamic assessment (EDA) procedures, in the form of an intervention focusing on characteristics of Goleman's emotional intelligence framework with the express purpose of inducing them to work with their emotions. Results showed that applying EDA procedures to reading assessment tasks made a difference in learners' level of performance in comparison to those who went through pure DA procedures who in turn performed significantly better than those who did not received DA in any form.

Integration of Treatment Innovation Planning and Implementation: Strategic Process Models and Organizational Challenges

PubMed Central

Lehman, Wayne E. K.; Simpson, D. Dwayne; Knight, Danica K.; Flynn, Patrick M.

2015-01-01

Sustained and effective use of evidence-based practices in substance abuse treatment services faces both clinical and contextual challenges. Implementation approaches are reviewed that rely on variations of plan-do-study-act (PDSA) cycles, but most emphasize conceptual identification of core components for system change strategies. A 2-phase procedural approach is therefore presented based on the integration of TCU models and related resources for improving treatment process and program change. Phase 1 focuses on the dynamics of clinical services, including stages of client recovery (cross-linked with targeted assessments and interventions), as the foundations for identifying and planning appropriate innovations to improve efficiency and effectiveness. Phase 2 shifts to the operational and organizational dynamics involved in implementing and sustaining innovations (including the stages of training, adoption, implementation, and practice). A comprehensive system of TCU assessments and interventions for client and program-level needs and functioning are summarized as well, with descriptions and guidelines for applications in practical settings. PMID:21443294

Development of procedures for calculating stiffness and damping properties of elastomers in engineering applications. Part 1: Verification of basic methods

NASA Technical Reports Server (NTRS)

Chiang, T.; Tessarzik, J. M.; Badgley, R. H.

1972-01-01

The primary aim of this investigation was verification of basic methods which are to be used in cataloging elastomer dynamic properties (stiffness and damping) in terms of viscoelastic model constants. These constants may then be used to predict dynamic properties for general elastomer shapes and operating conditions, thereby permitting optimum application of elastomers as energy absorption and/or energy storage devices in the control of vibrations in a broad variety of applications. The efforts reported involved: (1) literature search; (2) the design, fabrication and use of a test rig for obtaining elastomer dynamic test data over a wide range of frequencies, amplitudes, and preloads; and (3) the reduction of the test data, by means of a selected three-element elastomer model and specialized curve fitting techniques, to material properties. Material constants thus obtained have been used to calculate stiffness and damping for comparison with measured test data. These comparisons are excellent for a number of test conditions and only fair to poor for others. The results confirm the validity of the basic approach of the overall program and the mechanics of the cataloging procedure, and at the same time suggest areas in which refinements should be made.

LATIS3D: The Goal Standard for Laser-Tissue-Interaction Modeling

NASA Astrophysics Data System (ADS)

London, R. A.; Makarewicz, A. M.; Kim, B. M.; Gentile, N. A.; Yang, T. Y. B.

2000-03-01

The goal of this LDRD project has been to create LATIS3D-the world's premier computer program for laser-tissue interaction modeling. The development was based on recent experience with the 2D LATIS code and the ASCI code, KULL. With LATIS3D, important applications in laser medical therapy were researched including dynamical calculations of tissue emulsification and ablation, photothermal therapy, and photon transport for photodynamic therapy. This project also enhanced LLNL's core competency in laser-matter interactions and high-energy-density physics by pushing simulation codes into new parameter regimes and by attracting external expertise. This will benefit both existing LLNL programs such as ICF and SBSS and emerging programs in medical technology and other laser applications. The purpose of this project was to develop and apply a computer program for laser-tissue interaction modeling to aid in the development of new instruments and procedures in laser medicine.

Integrated aerodynamic/dynamic/structural optimization of helicopter rotor blades using multilevel decomposition

NASA Technical Reports Server (NTRS)

Walsh, Joanne L.; Young, Katherine C.; Pritchard, Jocelyn I.; Adelman, Howard M.; Mantay, Wayne R.

1995-01-01

This paper describes an integrated aerodynamic/dynamic/structural (IADS) optimization procedure for helicopter rotor blades. The procedure combines performance, dynamics, and structural analyses with a general-purpose optimizer using multilevel decomposition techniques. At the upper level, the structure is defined in terms of global quantities (stiffness, mass, and average strains). At the lower level, the structure is defined in terms of local quantities (detailed dimensions of the blade structure and stresses). The IADS procedure provides an optimization technique that is compatible with industrial design practices in which the aerodynamic and dynamic designs are performed at a global level and the structural design is carried out at a detailed level with considerable dialog and compromise among the aerodynamic, dynamic, and structural groups. The IADS procedure is demonstrated for several examples.

Multilevel decomposition approach to integrated aerodynamic/dynamic/structural optimization of helicopter rotor blades

NASA Technical Reports Server (NTRS)

Walsh, Joanne L.; Young, Katherine C.; Pritchard, Jocelyn I.; Adelman, Howard M.; Mantay, Wayne R.

1994-01-01

This paper describes an integrated aerodynamic, dynamic, and structural (IADS) optimization procedure for helicopter rotor blades. The procedure combines performance, dynamics, and structural analyses with a general purpose optimizer using multilevel decomposition techniques. At the upper level, the structure is defined in terms of local quantities (stiffnesses, mass, and average strains). At the lower level, the structure is defined in terms of local quantities (detailed dimensions of the blade structure and stresses). The IADS procedure provides an optimization technique that is compatible with industrial design practices in which the aerodynamic and dynamic design is performed at a global level and the structural design is carried out at a detailed level with considerable dialogue and compromise among the aerodynamic, dynamic, and structural groups. The IADS procedure is demonstrated for several cases.

Comprehensive analysis of helicopters with bearingless rotors

NASA Technical Reports Server (NTRS)

Murthy, V. R.

1988-01-01

A modified Galerkin method is developed to analyze the dynamic problems of multiple-load-path bearingless rotor blades. The development and selection of functions are quite parallel to CAMRAD procedures, greatly facilitating the implementation of the method into the CAMRAD program. A software is developed implementing the modified Galerkin method to determine free vibration characteristics of multiple-load-path rotor blades undergoing coupled flapwise bending, chordwise bending, twisting, and extensional motions. Results are in the process of being obtained by debugging the software.

Method to Enhance the Operation of an Optical Inspection Instrument Using Spatial Light Modulators

NASA Technical Reports Server (NTRS)

Trolinger, James; Lal, Amit; Jo, Joshua; Kupiec, Stephen

2012-01-01

For many aspheric and freeform optical components, existing interferometric solutions require a custom computer-generated hologram (CGH) to characterize the part. The overall objective of this research is to develop hardware and a procedure to produce a combined, dynamic, Hartmann/ Digital Holographic interferometry inspection system for a wide range of advanced optical components, including aspheric and freeform optics. This new instrument would have greater versatility and dynamic range than currently available measurement systems. The method uses a spatial light modulator to pre-condition wavefronts for imaging, interferometry, and data processing to improve the resolution and versatility of an optical inspection instrument. Existing interferometers and Hartmann inspection systems have either too small a dynamic range or insufficient resolution to characterize conveniently unusual optical surfaces like aspherical and freeform optics. For interferometers, a specially produced, computer-generated holographic optical element is needed to transform the wavefront to within the range of the interferometer. A new hybrid wavefront sensor employs newly available spatial light modulators (SLMs) as programmable holographic optical elements (HOEs). The HOE is programmed to enable the same instrument to inspect an optical element in stages, first by a Hartmann measurement, which has a very large dynamic range but less resolution. The first measurement provides the information required to precondition a reference wave that avails the measurement process to the more precise phase shifting interferometry. The SLM preconditions a wavefront before it is used to inspect an optical component. This adds important features to an optical inspection system, enabling not just wavefront conditioning for null testing and dynamic range extension, but also the creation of hybrid measurement procedures. This, for example, allows the combination of dynamic digital holography and Hartmann sensing procedures to cover a virtually unlimited dynamic range with high resolution. Digital holography technology brings all of the power and benefits of digital holographic interferometry to the requirement, while Hartmann-type wavefront sensors bring deflectometry technologies to the solution. The SLM can be used to generate arbitrary wavefronts in one leg of the interferometer, thereby greatly simplifying its use and extending its range. The SLM can also be used to modify the system into a dynamic Shack-Hartmann system, which is useful for optical components with large amounts of slope. By integrating these capabilities into a single instrument, the system will have tremendous flexibility to measure a variety of optical shapes accurately.

Source Authentication for Code Dissemination Supporting Dynamic Packet Size in Wireless Sensor Networks.

PubMed

Kim, Daehee; Kim, Dongwan; An, Sunshin

2016-07-09

Code dissemination in wireless sensor networks (WSNs) is a procedure for distributing a new code image over the air in order to update programs. Due to the fact that WSNs are mostly deployed in unattended and hostile environments, secure code dissemination ensuring authenticity and integrity is essential. Recent works on dynamic packet size control in WSNs allow enhancing the energy efficiency of code dissemination by dynamically changing the packet size on the basis of link quality. However, the authentication tokens attached by the base station become useless in the next hop where the packet size can vary according to the link quality of the next hop. In this paper, we propose three source authentication schemes for code dissemination supporting dynamic packet size. Compared to traditional source authentication schemes such as μTESLA and digital signatures, our schemes provide secure source authentication under the environment, where the packet size changes in each hop, with smaller energy consumption.

Source Authentication for Code Dissemination Supporting Dynamic Packet Size in Wireless Sensor Networks †

PubMed Central

Kim, Daehee; Kim, Dongwan; An, Sunshin

2016-01-01

Code dissemination in wireless sensor networks (WSNs) is a procedure for distributing a new code image over the air in order to update programs. Due to the fact that WSNs are mostly deployed in unattended and hostile environments, secure code dissemination ensuring authenticity and integrity is essential. Recent works on dynamic packet size control in WSNs allow enhancing the energy efficiency of code dissemination by dynamically changing the packet size on the basis of link quality. However, the authentication tokens attached by the base station become useless in the next hop where the packet size can vary according to the link quality of the next hop. In this paper, we propose three source authentication schemes for code dissemination supporting dynamic packet size. Compared to traditional source authentication schemes such as μTESLA and digital signatures, our schemes provide secure source authentication under the environment, where the packet size changes in each hop, with smaller energy consumption. PMID:27409616

Stochastic model of the NASA/MSFC ground facility for large space structures with uncertain parameters: The maximum entropy approach, part 2

NASA Technical Reports Server (NTRS)

Hsia, Wei Shen

1989-01-01

A validated technology data base is being developed in the areas of control/structures interaction, deployment dynamics, and system performance for Large Space Structures (LSS). A Ground Facility (GF), in which the dynamics and control systems being considered for LSS applications can be verified, was designed and built. One of the important aspects of the GF is to verify the analytical model for the control system design. The procedure is to describe the control system mathematically as well as possible, then to perform tests on the control system, and finally to factor those results into the mathematical model. The reduction of the order of a higher order control plant was addressed. The computer program was improved for the maximum entropy principle adopted in Hyland's MEOP method. The program was tested against the testing problem. It resulted in a very close match. Two methods of model reduction were examined: Wilson's model reduction method and Hyland's optimal projection (OP) method. Design of a computer program for Hyland's OP method was attempted. Due to the difficulty encountered at the stage where a special matrix factorization technique is needed in order to obtain the required projection matrix, the program was successful up to the finding of the Linear Quadratic Gaussian solution but not beyond. Numerical results along with computer programs which employed ORACLS are presented.

Wrist electrogoniometry: are current mathematical correction procedures effective in reducing crosstalk in functional assessment?

PubMed

Foltran, Fabiana A; Silva, Luciana C C B; Sato, Tatiana O; Coury, Helenice J C G

2013-01-01

The recording of human movement is an essential requirement for biomechanical, clinical, and occupational analysis, allowing assessment of postural variation, occupational risks, and preventive programs in physical therapy and rehabilitation. The flexible electrogoniometer (EGM), considered a reliable and accurate device, is used for dynamic recordings of different joints. Despite these advantages, the EGM is susceptible to measurement errors, known as crosstalk. There are two known types of crosstalk: crosstalk due to sensor rotation and inherent crosstalk. Correction procedures have been proposed to correct these errors; however no study has used both procedures in clinical measures for wrist movements with the aim to optimize the correction. To evaluate the effects of mathematical correction procedures on: 1) crosstalk due to forearm rotation, 2) inherent sensor crosstalk; and 3) the combination of these two procedures. 43 healthy subjects had their maximum range of motion of wrist flexion/extension and ulnar/radials deviation recorded by EGM. The results were analyzed descriptively, and procedures were compared by differences. There was no significant difference in measurements before and after the application of correction procedures (P<0.05). Furthermore, the differences between the correction procedures were less than 5° in most cases, having little impact on the measurements. Considering the time-consuming data analysis, the specific technical knowledge involved, and the inefficient results, the correction procedures are not recommended for wrist recordings by EGM.

Verification of an improved computational design procedure for TWT-dynamic refocuser-MDC systems with secondary electron emission losses

NASA Technical Reports Server (NTRS)

Ramins, P.; Force, D. A.; Palmer, R. W.; Dayton, J. A., Jr.; Kosmahl, H. G.

1986-01-01

A computational procedure for the design of TWT-refocuser-MDC systems was used to design a short 'dynamic' refocusing system and highly efficient four-stage depressed collector for a 200-W 8-18-GHz TWT. The computations were carried out with advanced multidimensional computer programs which model the electron beam as a series of disks of charge and follow their trajectories from the RF input of the TWT, through the slow-wave structure and refocusing section, to their points of impact in the depressed collector. Secondary emission losses in the MDC were treated semiquantitatively by injecting a representative beam of secondary electrons into the MDC analysis at the point of impact of each primary beam. A comparison of computed and measured TWT and MDC performance showed very good agreement. The electrodes of the MDC were fabricated from a particular form of isotropic graphite that was selected for its low secondary electron yield, thermal expansion characteristics, ease of machinability and vacuum properties. This MDC was tested at CW for more than 1000 h with negligible degradation in TWT and MDC performances.

A Novel Technique for Running the NASA Legacy Code LAPIN Synchronously With Simulations Developed Using Simulink

NASA Technical Reports Server (NTRS)

Vrnak, Daniel R.; Stueber, Thomas J.; Le, Dzu K.

2012-01-01

This report presents a method for running a dynamic legacy inlet simulation in concert with another dynamic simulation that uses a graphical interface. The legacy code, NASA's LArge Perturbation INlet (LAPIN) model, was coded using the FORTRAN 77 (The Portland Group, Lake Oswego, OR) programming language to run in a command shell similar to other applications that used the Microsoft Disk Operating System (MS-DOS) (Microsoft Corporation, Redmond, WA). Simulink (MathWorks, Natick, MA) is a dynamic simulation that runs on a modern graphical operating system. The product of this work has both simulations, LAPIN and Simulink, running synchronously on the same computer with periodic data exchanges. Implementing the method described in this paper avoided extensive changes to the legacy code and preserved its basic operating procedure. This paper presents a novel method that promotes inter-task data communication between the synchronously running processes.

A multi-purpose method for analysis of spur gear tooth loading

NASA Technical Reports Server (NTRS)

Kasuba, R.; Evans, J. W.; August, R.; Frater, J. L.

1981-01-01

A large digitized approach was developed for the static and dynamic load analysis of spur gearing. An iterative procedure was used to calculate directly the "variable-variable" gear mesh stiffness as a function of transmitted load, gear tooth profile errors, gear tooth deflections and gear hub torsional deformation, and position of contacting profile points. The developed approach can be used to analyze the loads, Hertz stresses, and PV for the normal and high contrast ratio gearing, presently the modeling is limited to the condition that for a given gear all teeth have identical spacing and profiles (with or without surface imperfections). Certain types of simulated sinusoidal profile errors and pitting can cause interruptions of the gear mesh stiffness function and, thus, increase the dynamic loads in spur gearing. In addition, a finite element stress and mesh subprogram was developed for future introduction into the main program for calculating the gear tooth bending stresses under dynamic loads.

4D Dynamic RNP Annual Interim Report-Year 1

NASA Technical Reports Server (NTRS)

Finkelsztein, Daniel M.; Sturdy, James L.; Alaverdi, Omeed; Chung, William W.; Salvano, Daniel; Klooster, Joel; Hochwarth, Joachim K.

2010-01-01

This Annual Interim Report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results obtained during the first year of this research effort to expand the RNP concept to 4 dimensions relative to a dynamic frame of reference. Joint Program Development Office (JPDO)Concepts of Operations for the Next Generation Air Transportation System (NextGen) considers 4 Dimension Trajectory (4DT) procedures a key enabler to Trajectory Based Operations (TBO). The JPDO defines 4DT as a precise description of an aircraft path in space and time . While NextGen assumes that this path is defined within an Earth-reference frame, many 4DT procedure implementations will require an aircraft to precisely navigate relative to a moving reference such as another aircraft to form aggregate flows or a weather cell to allow for flows to shift. Current methods of implementing routes and flight paths rely on aircraft meeting a Required Navigation Performance (RNP) specification and being equipped with a monitoring and alerting capability to annunciate when the aircraft system is unable to meet the performance specification required for the operation. Since all aircraft today operate within the NAS relative to fixed reference points, the current RNP definition is deemed satisfactory. However, it is not well understood how the current RNP construct will support NextGen 4DT procedures where aircraft operate relative to each other or to other dynamic frames of reference. The objective of this research effort is to analyze candidate 4DT procedures from both an Air Navigation Service Provider (ANSP) and aircraft perspective, to identify their specific navigational requirements, assess the shortcomings of the current RNP construct to meet these requirements, to propose an extended 4 Dimensional Dynamic RNP (4D Dynamic RNP) construct that accounts for the dynamic spatial and temporal nature of the selected 4DT procedures, and finally, to design an experiment using the Airspace and Traffic Operations Simulation (ATOS) system to validate the 4D Dynamic RNP construct. This Annual Interim Report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results obtained during the first year of this research effort to expand the RNP concept to 4 dimensions relative to a dynamic frame of reference. A comprehensive assessment of the state-of-the-art international implementation of current RNP was completed and presented in the Contractor Report RNP State-of-the-Art Assessment, Version 4, 17 December 2008 . The team defined in detail two 4DT operations, Airborne Precision Spacing and Self-Separation, that are ideally suited to be supported by 4D Dynamic RNP and developed their respective conceptual frameworks, Required Interval Management Performance (RIMP) Version 1.1, 13 April 2009 and Required Self Separation Performance (RSSP) Version 1.1, 13 April 2009 . Finally, the team started the development of a mathematical model and simulation tool for RIMP and RSSP scheduled to be delivered during the second year of this research effort.

Use of computational fluid dynamics in respiratory medicine.

PubMed

Fernández Tena, Ana; Casan Clarà, Pere

2015-06-01

Computational Fluid Dynamics (CFD) is a computer-based tool for simulating fluid movement. The main advantages of CFD over other fluid mechanics studies include: substantial savings in time and cost, the analysis of systems or conditions that are very difficult to simulate experimentally (as is the case of the airways), and a practically unlimited level of detail. We used the Ansys-Fluent CFD program to develop a conducting airway model to simulate different inspiratory flow rates and the deposition of inhaled particles of varying diameters, obtaining results consistent with those reported in the literature using other procedures. We hope this approach will enable clinicians to further individualize the treatment of different respiratory diseases. Copyright © 2014 SEPAR. Published by Elsevier Espana. All rights reserved.

Evolution of Flexible Multibody Dynamics for Simulation Applications Supporting Human Spaceflight

NASA Technical Reports Server (NTRS)

Huynh, An; Brain, Thomas A.; MacLean, John R.; Quiocho, Leslie J.

2016-01-01

During the course of transition from the Space Shuttle and International Space Station programs to the Orion and Journey to Mars exploration programs, a generic flexible multibody dynamics formulation and associated software implementation has evolved to meet an ever changing set of requirements at the NASA Johnson Space Center (JSC). Challenging problems related to large transitional topologies and robotic free-flyer vehicle capture/ release, contact dynamics, and exploration missions concept evaluation through simulation (e.g., asteroid surface operations) have driven this continued development. Coupled with this need is the requirement to oftentimes support human spaceflight operations in real-time. Moreover, it has been desirable to allow even more rapid prototyping of on-orbit manipulator and spacecraft systems, to support less complex infrastructure software for massively integrated simulations, to yield further computational efficiencies, and to take advantage of recent advances and availability of multi-core computing platforms. Since engineering analysis, procedures development, and crew familiarity/training for human spaceflight is fundamental to JSC's charter, there is also a strong desire to share and reuse models in both the non-realtime and real-time domains, with the goal of retaining as much multibody dynamics fidelity as possible. Three specific enhancements are reviewed here: (1) linked list organization to address large transitional topologies, (2) body level model order reduction, and (3) parallel formulation/implementation. This paper provides a detailed overview of these primary updates to JSC's flexible multibody dynamics algorithms as well as a comparison of numerical results to previous formulations and associated software.

The use of the articulated total body model as a robot dynamics simulation tool

NASA Technical Reports Server (NTRS)

Obergfell, Louise A.; Avula, Xavier J. R.; Kalegs, Ints

1988-01-01

The Articulated Total Body (ATB) model is a computer sumulation program which was originally developed for the study of aircrew member dynamics during ejection from high-speed aircraft. This model is totally three-dimensional and is based on the rigid body dynamics of coupled systems which use Euler's equations of motion with constraint relations of the type employed in the Lagrange method. In this paper the use of the ATB model as a robot dynamics simulation tool is discussed and various simulations are demonstrated. For this purpose the ATB model has been modified to allow for the application of torques at the joints as functions of state variables of the system. Specifically, the motion of a robotic arm with six revolute articulations with joint torques prescribed as functions of angular displacement and angular velocity are demonstrated. The simulation procedures developed in this work may serve as valuable tools for analyzing robotic mechanisms, dynamic effects, joint load transmissions, feed-back control algorithms employed in the actuator control and end-effector trajectories.

23 CFR 668.113 - Program and project procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Program and project procedures. 668.113 Section 668.113 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS EMERGENCY RELIEF PROGRAM Procedures for Federal-Aid Highways § 668.113 Program and project procedures. (a...

Generalized Symbolic Execution for Model Checking and Testing

NASA Technical Reports Server (NTRS)

Khurshid, Sarfraz; Pasareanu, Corina; Visser, Willem; Kofmeyer, David (Technical Monitor)

2003-01-01

Modern software systems, which often are concurrent and manipulate complex data structures must be extremely reliable. We present a novel framework based on symbolic execution, for automated checking of such systems. We provide a two-fold generalization of traditional symbolic execution based approaches: one, we define a program instrumentation, which enables standard model checkers to perform symbolic execution; two, we give a novel symbolic execution algorithm that handles dynamically allocated structures (e.g., lists and trees), method preconditions (e.g., acyclicity of lists), data (e.g., integers and strings) and concurrency. The program instrumentation enables a model checker to automatically explore program heap configurations (using a systematic treatment of aliasing) and manipulate logical formulae on program data values (using a decision procedure). We illustrate two applications of our framework: checking correctness of multi-threaded programs that take inputs from unbounded domains with complex structure and generation of non-isomorphic test inputs that satisfy a testing criterion. Our implementation for Java uses the Java PathFinder model checker.

Dynamic Open Inquiry Performances of High-School Biology Students

ERIC Educational Resources Information Center

Zion, Michal; Sadeh, Irit

2010-01-01

In examining open inquiry projects among high-school biology students, we found dynamic inquiry performances expressed in two criteria: "changes occurring during inquiry" and "procedural understanding". Characterizing performances in a dynamic open inquiry project can shed light on both the procedural and epistemological…

Analytical modeling of transport aircraft crash scenarios to obtain floor pulses

NASA Technical Reports Server (NTRS)

Wittlin, G.; Lackey, D.

1983-01-01

The KRAS program was used to analyze transport aircraft candidate crash scenarios. Aircraft floor pulses and seat/occupant responses are presented. Results show that: (1) longitudinal only pulses can be represented by equivalent step inputs and/or static requirements; (2) the L1649 crash test floor longitudinal pulse for the aft direction (forward inertia) is less than 9g static or an equivalent 5g pulse; aft inertia accelerations are extremely small ((ch76) 3g) for representative crash scenarios; (3) a viable procedure to relate crash scenario floor pulses to standard laboratory dynamic and static test data using state of the art analysis and test procedures was demonstrated; and (4) floor pulse magnitudes are expected to be lower for wide body aircraft than for smaller narrow body aircraft.

Episodic memory deficits slow down the dynamics of cognitive procedural learning in normal ageing

PubMed Central

Beaunieux, Hélène; Hubert, Valérie; Pitel, Anne Lise; Desgranges, Béatrice; Eustache, Francis

2009-01-01

Cognitive procedural learning is characterized by three phases, each involving distinct processes. Considering the implication of the episodic memory in the first cognitive stage, the impairment of this memory system might be responsible for a slowing down of the cognitive procedural learning dynamics in the course of aging. Performances of massed cognitive procedural learning were evaluated in older and younger participants using the Tower of Toronto task. Nonverbal intelligence and psychomotor abilities were used to analyze procedural dynamics, while episodic memory and working memory were assessed to measure their respective contributions to learning strategies. This experiment showed that older participants did not spontaneously invoke episodic memory and presented a slowdown in the cognitive procedural learning associated with a late involvement of working memory. These findings suggest that the slowdown in the cognitive procedural learning may be linked with the implementation of different learning strategies less involving episodic memory in older subjects. PMID:18654928

Three-dimensional turbopump flowfield analysis

NASA Technical Reports Server (NTRS)

Sharma, O. P.; Belford, K. A.; Ni, R. H.

1992-01-01

A program was conducted to develop a flow prediction method applicable to rocket turbopumps. The complex nature of a flowfield in turbopumps is described and examples of flowfields are discussed to illustrate that physics based models and analytical calculation procedures based on computational fluid dynamics (CFD) are needed to develop reliable design procedures for turbopumps. A CFD code developed at NASA ARC was used as the base code. The turbulence model and boundary conditions in the base code were modified, respectively, to: (1) compute transitional flows and account for extra rates of strain, e.g., rotation; and (2) compute surface heat transfer coefficients and allow computation through multistage turbomachines. Benchmark quality data from two and three-dimensional cascades were used to verify the code. The predictive capabilities of the present CFD code were demonstrated by computing the flow through a radial impeller and a multistage axial flow turbine. Results of the program indicate that the present code operated in a two-dimensional mode is a cost effective alternative to full three-dimensional calculations, and that it permits realistic predictions of unsteady loadings and losses for multistage machines.

Optimization of the launcher ascent trajectory leading to the global optimum without any initialization: the breakthrough of the Hamilton-Jacobi-Bellman approach

NASA Astrophysics Data System (ADS)

Bourgeois, E.; Bokanowski, O.; Zidani, H.; Désilles, A.

2018-06-01

The resolution of the launcher ascent trajectory problem by the so-called Hamilton-Jacobi-Bellman (HJB) approach, relying on the Dynamic Programming Principle, has been investigated. The method gives a global optimum and does not need any initialization procedure. Despite these advantages, this approach is seldom used because of the dicculties of computing the solution of the HJB equation for high dimension problems. The present study shows that an eccient resolution is found. An illustration of the method is proposed on a heavy class launcher, for a typical GEO (Geostationary Earth Orbit) mission. This study has been performed in the frame of the Centre National d'Etudes Spatiales (CNES) Launchers Research & Technology Program.

Advanced superposition methods for high speed turbopump vibration analysis

NASA Technical Reports Server (NTRS)

Nielson, C. E.; Campany, A. D.

1981-01-01

The small, high pressure Mark 48 liquid hydrogen turbopump was analyzed and dynamically tested to determine the cause of high speed vibration at an operating speed of 92,400 rpm. This approaches the design point operating speed of 95,000 rpm. The initial dynamic analysis in the design stage and subsequent further analysis of the rotor only dynamics failed to predict the vibration characteristics found during testing. An advanced procedure for dynamics analysis was used in this investigation. The procedure involves developing accurate dynamic models of the rotor assembly and casing assembly by finite element analysis. The dynamically instrumented assemblies are independently rap tested to verify the analytical models. The verified models are then combined by modal superposition techniques to develop a completed turbopump model where dynamic characteristics are determined. The results of the dynamic testing and analysis obtained are presented and methods of moving the high speed vibration characteristics to speeds above the operating range are recommended. Recommendations for use of these advanced dynamic analysis procedures during initial design phases are given.

CAM/LIFTER forces and friction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gabbey, D.J.; Lee, J.; Patterson, D.J.

1992-02-01

This report details the procedures used to measure the cam/lifter forces and friction. The present effort employed a Cummins LTA-10, and focuses on measurements and dynamic modeling of the injector train. The program was sponsored by the US Department of Energy in support of advanced diesel engine technology. The injector train was instrumented to record the instantaneous roller speed, roller pin friction torque, pushrod force, injector link force and cam speed. These measurements, together with lift profiles for pushrod and injector link displacement, enabled the friction work loss in the injector train to be determined. Other significant design criteria suchmore » as camshaft roller follower slippage and maximum loads on components were also determined. Future efforts will concentrate on the dynamic model, with tests run as required for correlation.« less

Improving balance, mobility, and dual-task performance in an adolescent with cerebral palsy: A case report.

PubMed

Fisher-Pipher, Sarah; Kenyon, Lisa K; Westman, Marci

2017-07-01

Improving functional mobility is often a desired outcome for adolescents with cerebral palsy (CP). Traditional neurorehabilitation approaches are frequently directed at impairments; however, improvements may not be carried over into functional mobility. The purpose of this case report was to describe the examination, intervention, and outcomes of a task-oriented physical therapy intervention program to improve dynamic balance, functional mobility, and dual-task performance in an adolescent with CP. The participant was a 15-year-old girl with spastic triplegic CP (Gross Motor Classification System Level II). Examination procedures included the Canadian Occupational Performance Measure, 6-minute walk test, Muscle Power Sprint Test, 10 x 5-meter sprint test, Timed Up and Down Stairs Test, Gross Motor Function Measure, Gillette Functional Assessment Questionnaire, and functional lower extremity strength tests. Intervention focused on task-oriented dynamic balance and mobility tasks that incorporated coordination and speed demands as well as task-specific lower extremity and trunk strengthening activities. Dual task demands were integrated into all intervention activities. Post-intervention testing revealed improvements in cardiovascular endurance, anaerobic power, agility, stair climbing, gross motor skills, and mobility. The participant appeared to benefit from a task-oriented program to improve dynamic balance, functional mobility, and dual-task performance.

General Rotorcraft Aeromechanical Stability Program (GRASP): Theory manual

NASA Technical Reports Server (NTRS)

Hodges, Dewey H.; Hopkins, A. Stewart; Kunz, Donald L.; Hinnant, Howard E.

1990-01-01

The general rotorcraft aeromechanical stability program (GRASP) was developed to calculate aeroelastic stability for rotorcraft in hovering flight, vertical flight, and ground contact conditions. GRASP is described in terms of its capabilities and its philosophy of modeling. The equations of motion that govern the physical system are described, as well as the analytical approximations used to derive them. The equations include the kinematical equation, the element equations, and the constraint equations. In addition, the solution procedures used by GRASP are described. GRASP is capable of treating the nonlinear static and linearized dynamic behavior of structures represented by arbitrary collections of rigid-body and beam elements. These elements may be connected in an arbitrary fashion, and are permitted to have large relative motions. The main limitation of this analysis is that periodic coefficient effects are not treated, restricting rotorcraft flight conditions to hover, axial flight, and ground contact. Instead of following the methods employed in other rotorcraft programs. GRASP is designed to be a hybrid of the finite-element method and the multibody methods used in spacecraft analysis. GRASP differs from traditional finite-element programs by allowing multiple levels of substructure in which the substructures can move and/or rotate relative to others with no small-angle approximations. This capability facilitates the modeling of rotorcraft structures, including the rotating/nonrotating interface and the details of the blade/root kinematics for various types. GRASP differs from traditional multibody programs by considering aeroelastic effects, including inflow dynamics (simple unsteady aerodynamics) and nonlinear aerodynamic coefficients.

12 CFR 326.3 - Security program.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 5 2013-01-01 2013-01-01 false Security program. 326.3 Section 326.3 Banks and... SECURITY DEVICES AND PROCEDURES AND BANK SECRECY ACT 1 COMPLIANCE Minimum Security Procedures § 326.3 Security program. (a) Contents of security program. The security program shall: (1) Establish procedures...

12 CFR 326.3 - Security program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 5 2014-01-01 2014-01-01 false Security program. 326.3 Section 326.3 Banks and... SECURITY DEVICES AND PROCEDURES AND BANK SECRECY ACT 1 COMPLIANCE Minimum Security Procedures § 326.3 Security program. (a) Contents of security program. The security program shall: (1) Establish procedures...

Rotor dynamic simulation and system identification methods for application to vacuum whirl data

NASA Technical Reports Server (NTRS)

Berman, A.; Giansante, N.; Flannelly, W. G.

1980-01-01

Methods of using rotor vacuum whirl data to improve the ability to model helicopter rotors were developed. The work consisted of the formulation of the equations of motion of elastic blades on a hub using a Galerkin method; the development of a general computer program for simulation of these equations; the study and implementation of a procedure for determining physical parameters based on measured data; and the application of a method for computing the normal modes and natural frequencies based on test data.

Robotic space simulation integration of vision algorithms into an orbital operations simulation

NASA Technical Reports Server (NTRS)

Bochsler, Daniel C.

1987-01-01

In order to successfully plan and analyze future space activities, computer-based simulations of activities in low earth orbit will be required to model and integrate vision and robotic operations with vehicle dynamics and proximity operations procedures. The orbital operations simulation (OOS) is configured and enhanced as a testbed for robotic space operations. Vision integration algorithms are being developed in three areas: preprocessing, recognition, and attitude/attitude rates. The vision program (Rice University) was modified for use in the OOS. Systems integration testing is now in progress.

7 CFR 205.668 - Noncompliance procedures under State organic programs.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Noncompliance procedures under State organic programs...) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE....668 Noncompliance procedures under State organic programs. (a) A State organic program's governing...

7 CFR 205.668 - Noncompliance procedures under State organic programs.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 3 2012-01-01 2012-01-01 false Noncompliance procedures under State organic programs...) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE....668 Noncompliance procedures under State organic programs. (a) A State organic program's governing...

7 CFR 205.668 - Noncompliance procedures under State organic programs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Noncompliance procedures under State organic programs...) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE....668 Noncompliance procedures under State organic programs. (a) A State organic program's governing...

40 CFR 136.5 - Approval of alternate test procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and to the Alternate Test Procedure Program Coordinator, Office of Science and Technology (4303... to the Alternate Test Procedure Program Coordinator, Office of Science and Technology (4303), Office... will be forwarded to the Alternate Test Procedure Program Coordinator, Office of Science and Technology...

40 CFR 136.5 - Approval of alternate test procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... and to the Alternate Test Procedure Program Coordinator, Office of Science and Technology (4303... to the Alternate Test Procedure Program Coordinator, Office of Science and Technology (4303), Office... will be forwarded to the Alternate Test Procedure Program Coordinator, Office of Science and Technology...

Nonlinear system guidance in the presence of transmission zero dynamics

NASA Technical Reports Server (NTRS)

Meyer, G.; Hunt, L. R.; Su, R.

1995-01-01

An iterative procedure is proposed for computing the commanded state trajectories and controls that guide a possibly multiaxis, time-varying, nonlinear system with transmission zero dynamics through a given arbitrary sequence of control points. The procedure is initialized by the system inverse with the transmission zero effects nulled out. Then the 'steady state' solution of the perturbation model with the transmission zero dynamics intact is computed and used to correct the initial zero-free solution. Both time domain and frequency domain methods are presented for computing the steady state solutions of the possibly nonminimum phase transmission zero dynamics. The procedure is illustrated by means of linear and nonlinear examples.

Easy handling of tectonic data: the programs TectonicVB for Mac and TectonicsFP for Windows™

NASA Astrophysics Data System (ADS)

Ortner, Hugo; Reiter, Franz; Acs, Peter

2002-12-01

TectonicVB for Macintosh and TectonicsFP for Windows TM operating systems are two menu-driven computer programs which allow the shared use of data on these environments. The programs can produce stereographic plots of orientation data (great circles, poles, lineations). Frequently used statistical procedures like calculation of eigenvalues and eigenvectors, calculation of mean vector with concentration parameters and confidence cone can be easily performed. Fault data can be plotted in stereographic projection (Angelier and Hoeppener plots). Sorting of datasets into homogeneous subsets and rotation of tectonic data can be performed in interactive two-diagram windows. The paleostress tensor can be calculated from fault data sets using graphical (calculation of kinematic axes and right dihedra method) or mathematical methods (direct inversion or numerical dynamical analysis). The calculations can be checked in dimensionless Mohr diagrams and fluctuation histograms.

Integration of treatment innovation planning and implementation: strategic process models and organizational challenges.

PubMed

Lehman, Wayne E K; Simpson, D Dwayne; Knight, Danica K; Flynn, Patrick M

2011-06-01

Sustained and effective use of evidence-based practices in substance abuse treatment services faces both clinical and contextual challenges. Implementation approaches are reviewed that rely on variations of plan-do-study-act (PDSA) cycles, but most emphasize conceptual identification of core components for system change strategies. A two-phase procedural approach is therefore presented based on the integration of Texas Christian University (TCU) models and related resources for improving treatment process and program change. Phase 1 focuses on the dynamics of clinical services, including stages of client recovery (cross-linked with targeted assessments and interventions), as the foundations for identifying and planning appropriate innovations to improve efficiency and effectiveness. Phase 2 shifts to the operational and organizational dynamics involved in implementing and sustaining innovations (including the stages of training, adoption, implementation, and practice). A comprehensive system of TCU assessments and interventions for client and program-level needs and functioning are summarized as well, with descriptions and guidelines for applications in practical settings. (PsycINFO Database Record (c) 2011 APA, all rights reserved).

77 FR 13887 - Energy Conservation Program: Test Procedures for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

... Energy Conservation Program: Test Procedures for Residential Clothes Washers; Final Rule #0;#0;Federal... Conservation Program: Test Procedures for Residential Clothes Washers AGENCY: Office of Energy Efficiency and...) establishes new test procedures for residential clothes washers under the Energy Policy and Conservation Act...

23 CFR 668.215 - Programming and project procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Programming and project procedures. 668.215 Section 668.215 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS EMERGENCY RELIEF PROGRAM Procedures for Federal Agencies for Federal Roads § 668.215 Programming...

23 CFR 668.215 - Programming and project procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Programming and project procedures. 668.215 Section 668.215 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS EMERGENCY RELIEF PROGRAM Procedures for Federal Agencies for Federal Roads § 668.215 Programming...

23 CFR 668.215 - Programming and project procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 23 Highways 1 2012-04-01 2012-04-01 false Programming and project procedures. 668.215 Section 668.215 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS EMERGENCY RELIEF PROGRAM Procedures for Federal Agencies for Federal Roads § 668.215 Programming...

23 CFR 668.215 - Programming and project procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Programming and project procedures. 668.215 Section 668.215 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS EMERGENCY RELIEF PROGRAM Procedures for Federal Agencies for Federal Roads § 668.215 Programming...

23 CFR 668.215 - Programming and project procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Programming and project procedures. 668.215 Section 668.215 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS EMERGENCY RELIEF PROGRAM Procedures for Federal Agencies for Federal Roads § 668.215 Programming...

78 FR 38455 - Energy Conservation Program: Test Procedures for Electric Motors

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-26

... Conservation Program: Test Procedures for Electric Motors; Proposed Rule #0;#0;Federal Register / Vol. 78, No... 431 [Docket No. EERE-2012-BT-TP-0043] RIN 1904-AC89 Energy Conservation Program: Test Procedures for... establishing definitions, specifying testing set-up procedures necessary to test, and extending DOE's existing...

31 CFR 501.808 - License application and other procedures applicable to economic sanctions programs.

Code of Federal Regulations, 2011 CFR

2011-07-01

... procedures applicable to economic sanctions programs. 501.808 Section 501.808 Money and Finance: Treasury... procedures applicable to economic sanctions programs. Upon submission to the Office of Management and Budget..., the license application and other procedures set forth in this subpart are applicable to economic...

Comprehensive Forced Response Analysis of J2X Turbine Bladed-Discs with 36- Degree Variation in CFD Loading

NASA Technical Reports Server (NTRS)

Elrod, David; Christensen, Eric; Brown, Andrew

2011-01-01

At NASA/MSFC, Structural Dynamics personnel continue to perform advanced analysis for the turbomachinery in the J2X Rocket Engine, which is under consideration for the new Space Launch System. One of the most challenging analyses in the program is predicting turbine blade structural capability. Resonance was predicted by modal analysis, so comprehensive forced response analyses using high fidelity cyclic symmetric finite element models were initiated as required. Analysis methodologies up to this point have assumed the flow field could be fully described by a sector, so the loading on every blade would be identical as it travelled through it. However, in the J2X the CFD flow field varied over the 360 deg of a revolution because of the flow speeds and tortuous axial path. MSFC therefore developed a complex procedure using Nastran Dmap's and Matlab scripts to apply this circumferentially varying loading onto the cyclically symmetric structural models to produce accurate dynamic stresses for every blade on the disk. This procedure is coupled with static, spin, and thermal loading to produce high cycle fatigue safety factors resulting in much more accurate analytical assessments of the blades.

aSi EPIDs for the in-vivo dosimetry of static and dynamic beams

NASA Astrophysics Data System (ADS)

Piermattei, A.; Cilla, S.; Azario, L.; Greco, F.; Russo, M.; Grusio, M.; Orlandini, L.; Fidanzio, A.

2015-10-01

Portal imaging by amorphous silicon (aSi) photodiode is currently the most applied technology for in-vivo dosimetry (IVD) of static and dynamic radiotherapy beams. The strategy, adopted in this work to perform the IVD procedure by aSi EPID, is based on: in patient reconstruction of the isocenter dose and day to day comparison between 2D-portal images to verify the reproducibility of treatment delivery. About 20.000 tests have been carried out in this last 3 years in 8 radiotherapy centers using the SOFTDISO program. The IVD results show that: (i) the procedure can be implemented for linacs of different manufacturer, (ii) the IVD analysis can be obtained on a computer screen, in quasi real time (about 2 min after the treatment delivery) and (iii) once the causes of the discrepancies were eliminated, all the global IVD tests for single patient were within the acceptance criteria defined by: ±5% for the isocenter dose, and Pγ<1≥90% of the checked points for the 2D portal image γ-analysis. This work is the result of a project supported by the Istituto Nazionale di Fisica Nucleare (INFN) and Università Cattolica del S.Cuore (UCSC).

LATDYN - PROGRAM FOR SIMULATION OF LARGE ANGLE TRANSIENT DYNAMICS OF FLEXIBLE AND RIGID STRUCTURES

NASA Technical Reports Server (NTRS)

Housner, J. M.

1994-01-01

LATDYN is a computer code for modeling the Large Angle Transient DYNamics of flexible articulating structures and mechanisms involving joints about which members rotate through large angles. LATDYN extends and brings together some of the aspects of Finite Element Structural Analysis, Multi-Body Dynamics, and Control System Analysis; three disciplines that have been historically separate. It combines significant portions of their distinct capabilities into one single analysis tool. The finite element formulation for flexible bodies in LATDYN extends the conventional finite element formulation by using a convected coordinate system for constructing the equation of motion. LATDYN's formulation allows for large displacements and rotations of finite elements subject to the restriction that deformations within each are small. Also, the finite element approach implemented in LATDYN provides a convergent path for checking solutions simply by increasing mesh density. For rigid bodies and joints LATDYN borrows extensively from methodology used in multi-body dynamics where rigid bodies may be defined and connected together through joints (hinges, ball, universal, sliders, etc.). Joints may be modeled either by constraints or by adding joint degrees of freedom. To eliminate error brought about by the separation of structural analysis and control analysis, LATDYN provides symbolic capabilities for modeling control systems which are integrated with the structural dynamic analysis itself. Its command language contains syntactical structures which perform symbolic operations which are also interfaced directly with the finite element structural model, bypassing the modal approximation. Thus, when the dynamic equations representing the structural model are integrated, the equations representing the control system are integrated along with them as a coupled system. This procedure also has the side benefit of enabling a dramatic simplification of the user interface for modeling control systems. Three FORTRAN computer programs, the LATDYN Program, the Preprocessor, and the Postprocessor, make up the collective LATDYN System. The Preprocessor translates user commands into a form which can be used while the LATDYN program provides the computational core. The Postprocessor allows the user to interactively plot and manage a database of LATDYN transient analysis results. It also includes special facilities for modeling control systems and for programming changes to the model which take place during analysis sequence. The documentation includes a Demonstration Problem Manual for the evaluation and verification of results and a Postprocessor guide. Because the program should be viewed as a byproduct of research on technology development, LATDYN's scope is limited. It does not have a wide library of finite elements, and 3-D Graphics are not available. Nevertheless, it does have a measure of "user friendliness". The LATDYN program was developed over a period of several years and was implemented on a CDC NOS/VE & Convex Unix computer. It is written in FORTRAN 77 and has a virtual memory requirement of 1.46 MB. The program was validated on a DEC MICROVAX operating under VMS 5.2.

Example-Based Automatic Music-Driven Conventional Dance Motion Synthesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Songhua; Fan, Rukun; Geng, Weidong

We introduce a novel method for synthesizing dance motions that follow the emotions and contents of a piece of music. Our method employs a learning-based approach to model the music to motion mapping relationship embodied in example dance motions along with those motions' accompanying background music. A key step in our method is to train a music to motion matching quality rating function through learning the music to motion mapping relationship exhibited in synchronized music and dance motion data, which were captured from professional human dance performance. To generate an optimal sequence of dance motion segments to match with amore » piece of music, we introduce a constraint-based dynamic programming procedure. This procedure considers both music to motion matching quality and visual smoothness of a resultant dance motion sequence. We also introduce a two-way evaluation strategy, coupled with a GPU-based implementation, through which we can execute the dynamic programming process in parallel, resulting in significant speedup. To evaluate the effectiveness of our method, we quantitatively compare the dance motions synthesized by our method with motion synthesis results by several peer methods using the motions captured from professional human dancers' performance as the gold standard. We also conducted several medium-scale user studies to explore how perceptually our dance motion synthesis method can outperform existing methods in synthesizing dance motions to match with a piece of music. These user studies produced very positive results on our music-driven dance motion synthesis experiments for several Asian dance genres, confirming the advantages of our method.« less

International Piping Integrity Research Group (IPIRG) Program. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilkowski, G.; Schmidt, R.; Scott, P.

1997-06-01

This is the final report of the International Piping Integrity Research Group (IPIRG) Program. The IPIRG Program was an international group program managed by the U.S. Nuclear Regulatory Commission and funded by a consortium of organizations from nine nations: Canada, France, Italy, Japan, Sweden, Switzerland, Taiwan, the United Kingdom, and the United States. The program objective was to develop data needed to verify engineering methods for assessing the integrity of circumferentially-cracked nuclear power plant piping. The primary focus was an experimental task that investigated the behavior of circumferentially flawed piping systems subjected to high-rate loadings typical of seismic events. Tomore » accomplish these objectives a pipe system fabricated as an expansion loop with over 30 meters of 16-inch diameter pipe and five long radius elbows was constructed. Five dynamic, cyclic, flawed piping experiments were conducted using this facility. This report: (1) provides background information on leak-before-break and flaw evaluation procedures for piping, (2) summarizes technical results of the program, (3) gives a relatively detailed assessment of the results from the pipe fracture experiments and complementary analyses, and (4) summarizes advances in the state-of-the-art of pipe fracture technology resulting from the IPIRG program.« less

45 CFR 309.35 - What are the procedures for review of a Tribal IV-D program application, plan or plan amendment?

Code of Federal Regulations, 2010 CFR

2010-10-01

...-D program application, plan or plan amendment? 309.35 Section 309.35 Public Welfare Regulations... ENFORCEMENT (IV-D) PROGRAM Tribal IV-D Program Application Procedures § 309.35 What are the procedures for review of a Tribal IV-D program application, plan or plan amendment? (a) The Secretary will promptly...

Gesture-Controlled Interface for Contactless Control of Various Computer Programs with a Hooking-Based Keyboard and Mouse-Mapping Technique in the Operating Room

PubMed Central

Park, Ben Joonyeon; Jang, Taekjin; Choi, Jong Woo; Kim, Namkug

2016-01-01

We developed a contactless interface that exploits hand gestures to effectively control medical images in the operating room. We developed an in-house program called GestureHook that exploits message hooking techniques to convert gestures into specific functions. For quantitative evaluation of this program, we used gestures to control images of a dynamic biliary CT study and compared the results with those of a mouse (8.54 ± 1.77 s to 5.29 ± 1.00 s; p < 0.001) and measured the recognition rates of specific gestures and the success rates of tasks based on clinical scenarios. For clinical applications, this program was set up in the operating room to browse images for plastic surgery. A surgeon browsed images from three different programs: CT images from a PACS program, volume-rendered images from a 3D PACS program, and surgical planning photographs from a basic image viewing program. All programs could be seamlessly controlled by gestures and motions. This approach can control all operating room programs without source code modification and provide surgeons with a new way to safely browse through images and easily switch applications during surgical procedures. PMID:26981146

Gesture-Controlled Interface for Contactless Control of Various Computer Programs with a Hooking-Based Keyboard and Mouse-Mapping Technique in the Operating Room.

PubMed

Park, Ben Joonyeon; Jang, Taekjin; Choi, Jong Woo; Kim, Namkug

2016-01-01

We developed a contactless interface that exploits hand gestures to effectively control medical images in the operating room. We developed an in-house program called GestureHook that exploits message hooking techniques to convert gestures into specific functions. For quantitative evaluation of this program, we used gestures to control images of a dynamic biliary CT study and compared the results with those of a mouse (8.54 ± 1.77 s to 5.29 ± 1.00 s; p < 0.001) and measured the recognition rates of specific gestures and the success rates of tasks based on clinical scenarios. For clinical applications, this program was set up in the operating room to browse images for plastic surgery. A surgeon browsed images from three different programs: CT images from a PACS program, volume-rendered images from a 3D PACS program, and surgical planning photographs from a basic image viewing program. All programs could be seamlessly controlled by gestures and motions. This approach can control all operating room programs without source code modification and provide surgeons with a new way to safely browse through images and easily switch applications during surgical procedures.

Computer Program for the Design and Off-Design Performance of Turbojet and Turbofan Engine Cycles

NASA Technical Reports Server (NTRS)

Morris, S. J.

1978-01-01

The rapid computer program is designed to be run in a stand-alone mode or operated within a larger program. The computation is based on a simplified one-dimensional gas turbine cycle. Each component in the engine is modeled thermo-dynamically. The component efficiencies used in the thermodynamic modeling are scaled for the off-design conditions from input design point values using empirical trends which are included in the computer code. The engine cycle program is capable of producing reasonable engine performance prediction with a minimum of computer execute time. The current computer execute time on the IBM 360/67 for one Mach number, one altitude, and one power setting is about 0.1 seconds. about 0.1 seconds. The principal assumption used in the calculation is that the compressor is operated along a line of maximum adiabatic efficiency on the compressor map. The fluid properties are computed for the combustion mixture, but dissociation is not included. The procedure included in the program is only for the combustion of JP-4, methane, or hydrogen.

Investigation to advance prediction techniques of the low-speed aerodynamics of V/STOL aircraft

NASA Technical Reports Server (NTRS)

Maskew, B.; Strash, D.; Nathman, J.; Dvorak, F. A.

1985-01-01

A computer program, VSAERO, has been applied to a number of V/STOL configurations with a view to advancing prediction techniques for the low-speed aerodynamic characteristics. The program couples a low-order panel method with surface streamline calculation and integral boundary layer procedures. The panel method--which uses piecewise constant source and doublet panels-includes an iterative procedure for wake shape and models boundary layer displacement effect using the source transpiration technique. Certain improvements to a basic vortex tube jet model were installed in the code prior to evaluation. Very promising results were obtained for surface pressures near a jet issuing at 90 deg from a flat plate. A solid core model was used in the initial part of the jet with a simple entrainment model. Preliminary representation of the downstream separation zone significantly improve the correlation. The program accurately predicted the pressure distribution inside the inlet on the Grumman 698-411 design at a range of flight conditions. Furthermore, coupled viscous/potential flow calculations gave very close correlation with experimentally determined operational boundaries dictated by the onset of separation inside the inlet. Experimentally observed degradation of these operational boundaries between nacelle-alone tests and tests on the full configuration were also indicated by the calculation. Application of the program to the General Dynamics STOL fighter design were equally encouraging. Very close agreement was observed between experiment and calculation for the effects of power on pressure distribution, lift and lift curve slope.

Study of propellant dynamics in a shuttle type launch vehicle

NASA Technical Reports Server (NTRS)

Jones, C. E.; Feng, G. C.

1972-01-01

A method and an associated digital computer program for evaluating the vibrational characteristics of large liquid-filled rigid wall tanks of general shape are presented. A solution procedure was developed in which slosh modes and frequencies are computed for systems mathematically modeled as assemblages of liquid finite elements. To retain sparsity in the assembled system mass and stiffness matrices, a compressible liquid element formulation was incorporated in the program. The approach taken in the liquid finite element formulation is compatible with triangular and quadrilateral structural finite elements so that the analysis of liquid motion can be coupled with flexible tank wall motion at some future time. The liquid element repertoire developed during the course of this study consists of a two-dimensional triangular element and a three-dimensional tetrahedral element.

48 CFR 19.1007 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Procedures. 19.1007 Section 19.1007 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS Small Business Competitiveness Demonstration Program 19.1007 Procedures...

CAM/LIFTER forces and friction. Final report, September 15, 1988--November 30, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gabbey, D.J.; Lee, J.; Patterson, D.J.

1992-02-01

This report details the procedures used to measure the cam/lifter forces and friction. The present effort employed a Cummins LTA-10, and focuses on measurements and dynamic modeling of the injector train. The program was sponsored by the US Department of Energy in support of advanced diesel engine technology. The injector train was instrumented to record the instantaneous roller speed, roller pin friction torque, pushrod force, injector link force and cam speed. These measurements, together with lift profiles for pushrod and injector link displacement, enabled the friction work loss in the injector train to be determined. Other significant design criteria suchmore » as camshaft roller follower slippage and maximum loads on components were also determined. Future efforts will concentrate on the dynamic model, with tests run as required for correlation.« less

Using transonic small disturbance theory for predicting the aeroelastic stability of a flexible wind-tunnel model

NASA Technical Reports Server (NTRS)

Silva, Walter A.; Bennett, Robert M.

1990-01-01

The CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) code, developed at the NASA - Langley Research Center, is applied to the Active Flexible Wing (AFW) wind tunnel model for prediction of the model's transonic aeroelastic behavior. Static aeroelastic solutions using CAP-TSD are computed. Dynamic (flutter) analyses are then performed as perturbations about the static aeroelastic deformations of the AFW. The accuracy of the static aeroelastic procedure is investigated by comparing analytical results to those from previous AFW wind tunnel experiments. Dynamic results are presented in the form of root loci at different Mach numbers for a heavy gas and air. The resultant flutter boundaries for both gases are also presented. The effects of viscous damping and angle-of-attack, on the flutter boundary in air, are presented as well.

Inference for finite-sample trajectories in dynamic multi-state site-occupancy models using hidden Markov model smoothing

USGS Publications Warehouse

Fiske, Ian J.; Royle, J. Andrew; Gross, Kevin

2014-01-01

Ecologists and wildlife biologists increasingly use latent variable models to study patterns of species occurrence when detection is imperfect. These models have recently been generalized to accommodate both a more expansive description of state than simple presence or absence, and Markovian dynamics in the latent state over successive sampling seasons. In this paper, we write these multi-season, multi-state models as hidden Markov models to find both maximum likelihood estimates of model parameters and finite-sample estimators of the trajectory of the latent state over time. These estimators are especially useful for characterizing population trends in species of conservation concern. We also develop parametric bootstrap procedures that allow formal inference about latent trend. We examine model behavior through simulation, and we apply the model to data from the North American Amphibian Monitoring Program.

45 CFR 1304.51 - Management systems and procedures.

Code of Federal Regulations, 2013 CFR

2013-10-01

... control program quality, maintain program accountability, and advise governing bodies, policy groups, and... DELEGATE AGENCIES Program Design and Management § 1304.51 Management systems and procedures. (a) Program... program planning that includes consultation with the program's governing body, policy groups, and program...

Computer Programs for Calculating the Isentropic Flow Properties for Mixtures of R-134a and Air

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.

2000-01-01

Three computer programs for calculating the isentropic flow properties of R-134a/air mixtures which were developed in support of the heavy gas conversion of the Langley Transonic Dynamics Tunnel (TDT) from dichlorodifluoromethane (R-12) to 1,1,1,2 tetrafluoroethane (R-134a) are described. The first program calculates the Mach number and the corresponding flow properties when the total temperature, total pressure, static pressure, and mole fraction of R-134a in the mixture are given. The second program calculates tables of isentropic flow properties for a specified set of free-stream Mach numbers given the total pressure, total temperature, and mole fraction of R-134a. Real-gas effects are accounted for in these programs by treating the gases comprising the mixture as both thermally and calorically imperfect. The third program is a specialized version of the first program in which the gases are thermally perfect. It was written to provide a simpler computational alternative to the first program in those cases where real-gas effects are not important. The theory and computational procedures underlying the programs are summarized, the equations used to compute the flow quantities of interest are given, and sample calculated results that encompass the operating conditions of the TDT are shown.

Advanced crew procedures development techniques: Procedures and performance program description

NASA Technical Reports Server (NTRS)

Arbet, J. D.; Mangiaracina, A. A.

1975-01-01

The Procedures and Performance Program (PPP) for operation in conjunction with the Shuttle Procedures Simulator (SPS) is described. The PPP user interface, the SPS/PPP interface, and the PPP applications software are discussed.

Degradation of learned skills: Effectiveness of practice methods on visual approach and landing skill retention

NASA Technical Reports Server (NTRS)

Sitterley, T. E.; Zaitzeff, L. P.; Berge, W. A.

1972-01-01

Flight control and procedural task skill degradation, and the effectiveness of retraining methods were evaluated for a simulated space vehicle approach and landing under instrument and visual flight conditions. Fifteen experienced pilots were trained and then tested after 4 months either without the benefits of practice or with static rehearsal, dynamic rehearsal or with dynamic warmup practice. Performance on both the flight control and procedure tasks degraded significantly after 4 months. The rehearsal methods effectively countered procedure task skill degradation, while dynamic rehearsal or a combination of static rehearsal and dynamic warmup practice was required for the flight control tasks. The quality of the retraining methods appeared to be primarily dependent on the efficiency of visual cue reinforcement.

The Development of a Novel Perfused Cadaver Model With Dynamic Vital Sign Regulation and Real-World Scenarios to Teach Surgical Skills and Error Management.

PubMed

Minneti, Michael; Baker, Craig J; Sullivan, Maura E

The landscape of graduate medical education has changed dramatically over the past decade and the traditional apprenticeship model has undergone scrutiny and modifications. The mandate of the 80-hour work-week, the introduction of integrated residency programs, increased global awareness about patient safety along with financial constraints have spurred changes in graduate educational practices. In addition, new technologies, more complex procedures, and a host of external constraints have changed where and how we teach technical and procedural skills. Simulation-based training has been embraced by the surgical community and has quickly become an essential component of most residency programs as a method to add efficacy to the traditional learning model. The purpose of this paper is twofold: (1) to describe the development of a perfused cadaver model with dynamic vital sign regulation, and (2) to assess the impact of a curriculum using this model and real world scenarios to teach surgical skills and error management. By providing a realistic training environment our aim is to enhance the acquisition of surgical skills and provide a more thorough assessment of resident performance. Twenty-six learners participated in the scenarios. Qualitative data showed that participants felt that the simulation model was realistic, and that participating in the scenarios helped them gain new knowledge, learn new surgical techniques and increase their confidence performing the skill in a clinical setting. Identifying the importance of both technical and nontechnical skills in surgical education has hastened the need for more realistic simulators and environments in which they are placed. Team members should be able to interact in ways that allow for a global display of their skills thus helping to provide a more comprehensive assessment by faculty and learners. Copyright © 2017 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Standardization and program effect analysis (Study 2.4). Volume 3: Design-to-cost analysis

NASA Technical Reports Server (NTRS)

Shiokari, T.

1975-01-01

The program procedures that were incorporated into an on-going "design-to-cost" spacecraft program are examined. Program procedures are the activities that support the development and operations of the flight unit: contract management, documents, integration meetings, engineering, and testing. This report is limited to the program procedures that were implemented, with emphasis on areas that may depart from normal satellite development practices.

A Sub-Orbital Platform for Flight Tests of Small Space Capsules

NASA Astrophysics Data System (ADS)

Pereira, P. Moraes A. L., Jr.; Silva, C. R.; Villas Bôas, D. J.; Corrêa, F., Jr.; Miyoshi, J. H.; Loures da Costa, L. E.

2002-01-01

In the development of a small recoverable space capsule, flight tests using sub-orbital rockets are considered. For this test series, a platform for aerodynamic and thermal measurements as also for qualification tests of onboard sub-systems and equipment was specified and is actually under development. This platform, known as SARA Suborbital, is specified to withstand a sub-orbital flight with the high performance sounding rocket VS40 and to be recovered at the sea. To perform the testing program, a flight trajectory with adequate aeroballistic parameters, as for instance high velocities in dense atmosphere and average re-entry velocity, is considered. The testing program includes measurements of aerodynamic pressures and thermal characteristics, three- axis acceleration, acoustic pressure level inside the platform and vibration environment. Beside this, tests to characterise the performance of the data acquisition and transmission system, the micro-gravity environment and to qualify the recovery system will be carried out. During the return flight, the dynamics of parachutes deployment and platform water impact, as also rescue procedures will also be observed. The present article shows the concept of the platform, describes in detail the experiments, and concludes with a discussion on the flight trajectory and recovery procedure.

Towards a Certified Lightweight Array Bound Checker for Java Bytecode

NASA Technical Reports Server (NTRS)

Pichardie, David

2009-01-01

Dynamic array bound checks are crucial elements for the security of a Java Virtual Machines. These dynamic checks are however expensive and several static analysis techniques have been proposed to eliminate explicit bounds checks. Such analyses require advanced numerical and symbolic manipulations that 1) penalize bytecode loading or dynamic compilation, 2) complexify the trusted computing base. Following the Foundational Proof Carrying Code methodology, our goal is to provide a lightweight bytecode verifier for eliminating array bound checks that is both efficient and trustable. In this work, we define a generic relational program analysis for an imperative, stackoriented byte code language with procedures, arrays and global variables and instantiate it with a relational abstract domain as polyhedra. The analysis has automatic inference of loop invariants and method pre-/post-conditions, and efficient checking of analysis results by a simple checker. Invariants, which can be large, can be specialized for proving a safety policy using an automatic pruning technique which reduces their size. The result of the analysis can be checked efficiently by annotating the program with parts of the invariant together with certificates of polyhedral inclusions. The resulting checker is sufficiently simple to be entirely certified within the Coq proof assistant for a simple fragment of the Java bytecode language. During the talk, we will also report on our ongoing effort to scale this approach for the full sequential JVM.

Dynamic metabolic modeling for a MAB bioprocess.

PubMed

Gao, Jianying; Gorenflo, Volker M; Scharer, Jeno M; Budman, Hector M

2007-01-01

Production of monoclonal antibodies (MAb) for diagnostic or therapeutic applications has become an important task in the pharmaceutical industry. The efficiency of high-density reactor systems can be potentially increased by model-based design and control strategies. Therefore, a reliable kinetic model for cell metabolism is required. A systematic procedure based on metabolic modeling is used to model nutrient uptake and key product formation in a MAb bioprocess during both the growth and post-growth phases. The approach combines the key advantages of stoichiometric and kinetic models into a complete metabolic network while integrating the regulation and control of cellular activity. This modeling procedure can be easily applied to any cell line during both the cell growth and post-growth phases. Quadratic programming (QP) has been identified as a suitable method to solve the underdetermined constrained problem related to model parameter identification. The approach is illustrated for the case of murine hybridoma cells cultivated in stirred spinners.

42 CFR 422.502 - Evaluation and determination procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SERVICES (CONTINUED) MEDICARE PROGRAM MEDICARE ADVANTAGE PROGRAM Application Procedures and Contracts for Medicare Advantage Organizations § 422.502 Evaluation and determination procedures. (a) Basis for...

Recent advances in integrated multidisciplinary optimization of rotorcraft

NASA Technical Reports Server (NTRS)

Adelman, Howard M.; Walsh, Joanne L.; Pritchard, Jocelyn I.

1992-01-01

A joint activity involving NASA and Army researchers at NASA LaRC to develop optimization procedures to improve the rotor blade design process by integrating appropriate disciplines and accounting for all of the important interactions among the disciplines is described. The disciplines involved include rotor aerodynamics, rotor dynamics, rotor structures, airframe dynamics, and acoustics. The work is focused on combining these five key disciplines in an optimization procedure capable of designing a rotor system to satisfy multidisciplinary design requirements. Fundamental to the plan is a three-phased approach. In phase 1, the disciplines of blade dynamics, blade aerodynamics, and blade structure are closely coupled while acoustics and airframe dynamics are decoupled and are accounted for as effective constraints on the design for the first three disciplines. In phase 2, acoustics is integrated with the first three disciplines. Finally, in phase 3, airframe dynamics is integrated with the other four disciplines. Representative results from work performed to date are described. These include optimal placement of tuning masses for reduction of blade vibratory shear forces, integrated aerodynamic/dynamic optimization, and integrated aerodynamic/dynamic/structural optimization. Examples of validating procedures are described.

Recent advances in multidisciplinary optimization of rotorcraft

NASA Technical Reports Server (NTRS)

Adelman, Howard M.; Walsh, Joanne L.; Pritchard, Jocelyn I.

1992-01-01

A joint activity involving NASA and Army researchers at NASA LaRC to develop optimization procedures to improve the rotor blade design process by integrating appropriate disciplines and accounting for all of the important interactions among the disciplines is described. The disciplines involved include rotor aerodynamics, rotor dynamics, rotor structures, airframe dynamics, and acoustics. The work is focused on combining these five key disciplines in an optimization procedure capable of designing a rotor system to satisfy multidisciplinary design requirements. Fundamental to the plan is a three-phased approach. In phase 1, the disciplines of blade dynamics, blade aerodynamics, and blade structure are closely coupled while acoustics and airframe dynamics are decoupled and are accounted for as effective constraints on the design for the first three disciplines. In phase 2, acoustics is integrated with the first three disciplines. Finally, in phase 3, airframe dynamics is integrated with the other four disciplines. Representative results from work performed to date are described. These include optimal placement of tuning masses for reduction of blade vibratory shear forces, integrated aerodynamic/dynamic optimization, and integrated aerodynamic/dynamic/structural optimization. Examples of validating procedures are described.

19 CFR 101.9 - Test programs or procedures; alternate requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... test and the basis for selecting participants; and, (2) Post publication requirement. Within a... 19 Customs Duties 1 2014-04-01 2014-04-01 false Test programs or procedures; alternate... SECURITY; DEPARTMENT OF THE TREASURY GENERAL PROVISIONS § 101.9 Test programs or procedures; alternate...

78 FR 49607 - Energy Conservation Program: Test Procedures for Residential Clothes Dryers

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-14

... reasonably designed to produce test results which measure energy efficiency, energy use or estimated annual... Energy Conservation Program: Test Procedures for Residential Clothes Dryers; Final Rule #0;#0;Federal... Conservation Program: Test Procedures for Residential Clothes Dryers AGENCY: Office of Energy Efficiency and...

Quantum wavepacket ab initio molecular dynamics: an approach for computing dynamically averaged vibrational spectra including critical nuclear quantum effects.

PubMed

Sumner, Isaiah; Iyengar, Srinivasan S

2007-10-18

We have introduced a computational methodology to study vibrational spectroscopy in clusters inclusive of critical nuclear quantum effects. This approach is based on the recently developed quantum wavepacket ab initio molecular dynamics method that combines quantum wavepacket dynamics with ab initio molecular dynamics. The computational efficiency of the dynamical procedure is drastically improved (by several orders of magnitude) through the utilization of wavelet-based techniques combined with the previously introduced time-dependent deterministic sampling procedure measure to achieve stable, picosecond length, quantum-classical dynamics of electrons and nuclei in clusters. The dynamical information is employed to construct a novel cumulative flux/velocity correlation function, where the wavepacket flux from the quantized particle is combined with classical nuclear velocities to obtain the vibrational density of states. The approach is demonstrated by computing the vibrational density of states of [Cl-H-Cl]-, inclusive of critical quantum nuclear effects, and our results are in good agreement with experiment. A general hierarchical procedure is also provided, based on electronic structure harmonic frequencies, classical ab initio molecular dynamics, computation of nuclear quantum-mechanical eigenstates, and employing quantum wavepacket ab initio dynamics to understand vibrational spectroscopy in hydrogen-bonded clusters that display large degrees of anharmonicities.

Dynamic Assessment in School Psychology

ERIC Educational Resources Information Center

Lidz, Carol S.

2009-01-01

Dynamic assessment (DA) is a generic term for a variety of procedures that embed intervention within the assessment itself. Typically administered in pretest-intervention-posttest format, DA procedures provide information about the response and responsiveness of the individual to intervention and generate ideas and evidence about potentially…

Procedural and Logic Programming: A Comparison.

ERIC Educational Resources Information Center

Watkins, Will; And Others

1988-01-01

Examines the similarities and fundamental differences between procedural programing and logic programing by comparing LogoWriter and PROLOG. Suggests that PROLOG may be a good first programing language for students to learn. (MVL)

20 CFR 633.316 - Closeout procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Closeout procedures. 633.316 Section 633.316 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR MIGRANT AND SEASONAL FARMWORKER PROGRAMS Program Design and Administrative Procedures § 633.316 Closeout procedures. Grant...

19 CFR 101.9 - Test programs or procedures; alternate requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... requirements. (a) General testing. For purposes of conducting a test program or procedure designed to evaluate... test and the basis for selecting participants; and, (2) Post publication requirement. Within a... 19 Customs Duties 1 2010-04-01 2010-04-01 false Test programs or procedures; alternate...

19 CFR 101.9 - Test programs or procedures; alternate requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... requirements. (a) General testing. For purposes of conducting a test program or procedure designed to evaluate... test and the basis for selecting participants; and, (2) Post publication requirement. Within a... 19 Customs Duties 1 2013-04-01 2013-04-01 false Test programs or procedures; alternate...

19 CFR 101.9 - Test programs or procedures; alternate requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... requirements. (a) General testing. For purposes of conducting a test program or procedure designed to evaluate... test and the basis for selecting participants; and, (2) Post publication requirement. Within a... 19 Customs Duties 1 2011-04-01 2011-04-01 false Test programs or procedures; alternate...

19 CFR 101.9 - Test programs or procedures; alternate requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... requirements. (a) General testing. For purposes of conducting a test program or procedure designed to evaluate... test and the basis for selecting participants; and, (2) Post publication requirement. Within a... 19 Customs Duties 1 2012-04-01 2012-04-01 false Test programs or procedures; alternate...

49 CFR Appendix B to Part 599 - Engine Disablement Procedures for the CARS Program

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Engine Disablement Procedures for the CARS Program B Appendix B to Part 599 Transportation Other Regulations Relating to Transportation (Continued...—Engine Disablement Procedures for the CARS Program ER29JY09.006 ...

49 CFR Appendix B to Part 599 - Engine Disablement Procedures for the CARS Program

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Engine Disablement Procedures for the CARS Program B Appendix B to Part 599 Transportation Other Regulations Relating to Transportation (Continued...—Engine Disablement Procedures for the CARS Program ER29JY09.006 ...

49 CFR Appendix B to Part 599 - Engine Disablement Procedures for the CARS Program

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Engine Disablement Procedures for the CARS Program B Appendix B to Part 599 Transportation Other Regulations Relating to Transportation (Continued...—Engine Disablement Procedures for the CARS Program ER29JY09.006 ...

49 CFR Appendix B to Part 599 - Engine Disablement Procedures for the CARS Program

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Engine Disablement Procedures for the CARS Program B Appendix B to Part 599 Transportation Other Regulations Relating to Transportation (Continued...—Engine Disablement Procedures for the CARS Program ER29JY09.006 ...

49 CFR Appendix B to Part 599 - Engine Disablement Procedures for the CARS Program

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Engine Disablement Procedures for the CARS Program B Appendix B to Part 599 Transportation Other Regulations Relating to Transportation (Continued...—Engine Disablement Procedures for the CARS Program ER29JY09.006 ...

10 CFR 26.403 - Written policy and procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Written policy and procedures. 26.403 Section 26.403 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS FFD Program for Construction § 26.403 Written policy and procedures. (a) Licensees and other entities who implement an FFD program under this...

10 CFR 26.403 - Written policy and procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Written policy and procedures. 26.403 Section 26.403 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS FFD Program for Construction § 26.403 Written policy and procedures. (a) Licensees and other entities who implement an FFD program under this...

10 CFR 26.403 - Written policy and procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Written policy and procedures. 26.403 Section 26.403 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS FFD Program for Construction § 26.403 Written policy and procedures. (a) Licensees and other entities who implement an FFD program under this...

23 CFR 1200.26 - Non-compliance.

Code of Federal Regulations, 2010 CFR

2010-04-01

... TRANSPORTATION PROCEDURES FOR STATE HIGHWAY SAFETY PROGRAMS UNIFORM PROCEDURES FOR STATE HIGHWAY SAFETY PROGRAMS Implementation and Management of the Highway Safety Program § 1200.26 Non-compliance. Where a State is found to... special conditions for high-risk grantees and the enforcement procedures of 49 CFR part 18, or the...

10 CFR 26.403 - Written policy and procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Written policy and procedures. 26.403 Section 26.403 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS FFD Program for Construction § 26.403 Written policy and procedures. (a) Licensees and other entities who implement an FFD program under this...

10 CFR 26.403 - Written policy and procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Written policy and procedures. 26.403 Section 26.403 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS FFD Program for Construction § 26.403 Written policy and procedures. (a) Licensees and other entities who implement an FFD program under this...

Student Services Program Planning and Evaluation: Responsibility, Procedures, Instrument, and Guidelines.

ERIC Educational Resources Information Center

Repp, Charles A.; Brach, Ronald C.

The manual provides a rationale, procedural guidelines, time-schedules, instruments, and supporting documentation for student services program evaluation at SUNY Agricultural and Technical College, Delhi. Six procedural guidelines include: (1) all programs and services should be evaluated at least once every four years, with provision for annual…

Interactive outlining: an improved approach using active contours

NASA Astrophysics Data System (ADS)

Daneels, Dirk; van Campenhout, David; Niblack, Carlton W.; Equitz, Will; Barber, Ron; Fierens, Freddy

1993-04-01

The purpose of our work is to outline objects on images in an interactive environment. We use an improved method based on energy minimizing active contours or `snakes.' Kass et al., proposed a variational technique; Amini used dynamic programming; and Williams and Shah introduced a fast, greedy algorithm. We combine the advantages of the latter two methods in a two-stage algorithm. The first stage is a greedy procedure that provides fast initial convergence. It is enhanced with a cost term that extends over a large number of points to avoid oscillations. The second stage, when accuracy becomes important, uses dynamic programming. This step is accelerated by the use of alternating search neighborhoods and by dropping stable points from the iterations. We have also added several features for user interaction. First, the user can define points of high confidence. Mathematically, this results in an extra cost term and, in that way, the robustness in difficult areas (e.g., noisy edges, sharp corners) is improved. We also give the user the possibility of incremental contour tracking, thus providing feedback on the refinement process. The algorithm has been tested on numerous photographic clip art images and extensive tests on medical images are in progress.

Computer program for the computation of total sediment discharge by the modified Einstein procedure

USGS Publications Warehouse

Stevens, H.H.

1985-01-01

Two versions of a computer program to compute total sediment discharge by the modified Einstein procedure are presented. The FORTRAN 77 language version is for use on the PRIME computer, and the BASIC language version is for use on most microcomputers. The program contains built-in limitations and input-output options that closely follow the original modified Einstein procedure. Program documentation and listings of both versions of the program are included. (USGS)

A study to evaluate STS heads-up ascent trajectory performance employing a minimum-Hamiltonian optimization strategy

NASA Technical Reports Server (NTRS)

Sinha, Sujit

1988-01-01

A study was conducted to evaluate the performance implications of a heads-up ascent flight design for the Space Transportation System, as compared to the current heads-down flight mode. The procedure involved the use of the Minimum Hamiltonian Ascent Shuttle Trajectory Evaluation Program, which is a three-degree-of-freedom moment balance simulation of shuttle ascent. A minimum-Hamiltonian optimization strategy was employed to maximize injection weight as a function of maximum dynamic pressure constraint and Solid Rocket Motor burnrate. Performance Reference Mission Four trajectory groundrules were used for consistency. The major conclusions are that for heads-up ascent and a mission nominal design maximum dynamic pressure value of 680 psf, the optimum solid motor burnrate is 0.394 ips, which produces a performance enhancement of 4293 lbm relative to the baseline heads-down ascent, with 0.368 ips burnrate solid motors and a 680 psf dynamic pressure constraint. However, no performance advantage exists for heads-up flight if the current Solid Rocket Motor target burnrate of 0.368 ips is used. The advantage of heads-up ascent flight employing the current burnrate is that Space Shuttle Main Engine throttling for dynamic pressure control is not necessary.

Versatile and declarative dynamic programming using pair algebras.

PubMed

Steffen, Peter; Giegerich, Robert

2005-09-12

Dynamic programming is a widely used programming technique in bioinformatics. In sharp contrast to the simplicity of textbook examples, implementing a dynamic programming algorithm for a novel and non-trivial application is a tedious and error prone task. The algebraic dynamic programming approach seeks to alleviate this situation by clearly separating the dynamic programming recurrences and scoring schemes. Based on this programming style, we introduce a generic product operation of scoring schemes. This leads to a remarkable variety of applications, allowing us to achieve optimizations under multiple objective functions, alternative solutions and backtracing, holistic search space analysis, ambiguity checking, and more, without additional programming effort. We demonstrate the method on several applications for RNA secondary structure prediction. The product operation as introduced here adds a significant amount of flexibility to dynamic programming. It provides a versatile testbed for the development of new algorithmic ideas, which can immediately be put to practice.

Development and application of a technique for reducing airframe finite element models for dynamics analysis

NASA Technical Reports Server (NTRS)

Hashemi-Kia, Mostafa; Toossi, Mostafa

1990-01-01

A computational procedure for the reduction of large finite element models was developed. This procedure is used to obtain a significantly reduced model while retaining the essential global dynamic characteristics of the full-size model. This reduction procedure is applied to the airframe finite element model of AH-64A Attack Helicopter. The resulting reduced model is then validated by application to a vibration reduction study.

Procedural volume and structure of interventional pulmonary fellowships: a survey of fellows and fellowship program directors.

PubMed

Yarmus, Lonny; Feller-Kopman, David; Imad, Melhem; Kim, Stephanie; Lee, Hans J

2013-09-01

Current interventional pulmonary (IP) procedural guidelines for competency are based on expert opinion. There are few objective data to support competency metrics for IP procedures. This survey reports procedural volume during IP fellowships to help define new standards in training and curriculum development. A web-based survey was developed to evaluate IP training procedural volume. The survey was administered to all US and Canadian IP fellowship directors and graduates in training from 2006 to 2011. The survey inquired about all diagnostic and therapeutic procedures performed during the specialized year of IP training. Questions regarding the training program structure were collected and analyzed. There was a 92.5% fellow response rate (37 of 40) and 77% fellowship director response rate (10 of 13) from programs in existence at the time of the survey. Procedural volume was consistent between fellowship directors and graduates (P = .64). Although there was a wide range of procedural volume and types of procedures between different programs, the procedural mean volumes were all significantly higher than the American College of Chest Physicians (ACCP) and American Thoracic Society/European Respiratory Society (ATS/ERS) guideline recommendations (P < .005). US and Canadian IP fellowships produce fellows with variable procedural volumes; however, these are significantly higher than ACCP and ATS/ERS guidelines for most programs and procedures. With a uniform training curriculum being adopted by the majority of IP fellowship programs in the United States and Canada, as well as data showing improved core knowledge in IP fellows undergoing a dedicated year of additional training, further metrics examining the impact of advanced IP training on patient outcomes are needed.

Flexible and Comprehensive Implementation of MD-PMM Approach in a General and Robust Code.

PubMed

Carrillo-Parramon, Oliver; Del Galdo, Sara; Aschi, Massimiliano; Mancini, Giordano; Amadei, Andrea; Barone, Vincenzo

2017-11-14

The Perturbed Matrix Method (PMM) approach to be used in combination with Molecular Dynamics (MD) trajectories (MD-PMM) has been recoded from scratch, improved in several aspects, and implemented in the Gaussian suite of programs for allowing a user-friendly and yet flexible tool to estimate quantum chemistry observables in complex systems in condensed phases. Particular attention has been devoted to a description of rigid and flexible quantum centers together with powerful essential dynamics and clustering approaches. The default implementation is fully black-box and does not require any external action concerning both MD and PMM sections. At the same time, fine-tuning of different parameters and use of external data are allowed in all the steps of the procedure. Two specific systems (Tyrosine and Uridine) have been reinvestigated with the new version of the code in order to validate the implementation, check the performances, and illustrate some new features.

Computational strategies in the dynamic simulation of constrained flexible MBS

NASA Technical Reports Server (NTRS)

Amirouche, F. M. L.; Xie, M.

1993-01-01

This research focuses on the computational dynamics of flexible constrained multibody systems. At first a recursive mapping formulation of the kinematical expressions in a minimum dimension as well as the matrix representation of the equations of motion are presented. The method employs Kane's equation, FEM, and concepts of continuum mechanics. The generalized active forces are extended to include the effects of high temperature conditions, such as creep, thermal stress, and elastic-plastic deformation. The time variant constraint relations for rolling/contact conditions between two flexible bodies are also studied. The constraints for validation of MBS simulation of gear meshing contact using a modified Timoshenko beam theory are also presented. The last part deals with minimization of vibration/deformation of the elastic beam in multibody systems making use of time variant boundary conditions. The above methodologies and computational procedures developed are being implemented in a program called DYAMUS.

Update on Integrated Optical Design Analyzer

NASA Technical Reports Server (NTRS)

Moore, James D., Jr.; Troy, Ed

2003-01-01

Updated information on the Integrated Optical Design Analyzer (IODA) computer program has become available. IODA was described in Software for Multidisciplinary Concurrent Optical Design (MFS-31452), NASA Tech Briefs, Vol. 25, No. 10 (October 2001), page 8a. To recapitulate: IODA facilitates multidisciplinary concurrent engineering of highly precise optical instruments. The architecture of IODA was developed by reviewing design processes and software in an effort to automate design procedures. IODA significantly reduces design iteration cycle time and eliminates many potential sources of error. IODA integrates the modeling efforts of a team of experts in different disciplines (e.g., optics, structural analysis, and heat transfer) working at different locations and provides seamless fusion of data among thermal, structural, and optical models used to design an instrument. IODA is compatible with data files generated by the NASTRAN structural-analysis program and the Code V (Registered Trademark) optical-analysis program, and can be used to couple analyses performed by these two programs. IODA supports multiple-load-case analysis for quickly accomplishing trade studies. IODA can also model the transient response of an instrument under the influence of dynamic loads and disturbances.

The Optimization Based Dynamic and Cyclic Working Strategies for Rechargeable Wireless Sensor Networks with Multiple Base Stations and Wireless Energy Transfer Devices

PubMed Central

Ding, Xu; Han, Jianghong; Shi, Lei

2015-01-01

In this paper, the optimal working schemes for wireless sensor networks with multiple base stations and wireless energy transfer devices are proposed. The wireless energy transfer devices also work as data gatherers while charging sensor nodes. The wireless sensor network is firstly divided into sub networks according to the concept of Voronoi diagram. Then, the entire energy replenishing procedure is split into the pre-normal and normal energy replenishing stages. With the objective of maximizing the sojourn time ratio of the wireless energy transfer device, a continuous time optimization problem for the normal energy replenishing cycle is formed according to constraints with which sensor nodes and wireless energy transfer devices should comply. Later on, the continuous time optimization problem is reshaped into a discrete multi-phased optimization problem, which yields the identical optimality. After linearizing it, we obtain a linear programming problem that can be solved efficiently. The working strategies of both sensor nodes and wireless energy transfer devices in the pre-normal replenishing stage are also discussed in this paper. The intensive simulations exhibit the dynamic and cyclic working schemes for the entire energy replenishing procedure. Additionally, a way of eliminating “bottleneck” sensor nodes is also developed in this paper. PMID:25785305

The optimization based dynamic and cyclic working strategies for rechargeable wireless sensor networks with multiple base stations and wireless energy transfer devices.

PubMed

Ding, Xu; Han, Jianghong; Shi, Lei

2015-03-16

In this paper, the optimal working schemes for wireless sensor networks with multiple base stations and wireless energy transfer devices are proposed. The wireless energy transfer devices also work as data gatherers while charging sensor nodes. The wireless sensor network is firstly divided into sub networks according to the concept of Voronoi diagram. Then, the entire energy replenishing procedure is split into the pre-normal and normal energy replenishing stages. With the objective of maximizing the sojourn time ratio of the wireless energy transfer device, a continuous time optimization problem for the normal energy replenishing cycle is formed according to constraints with which sensor nodes and wireless energy transfer devices should comply. Later on, the continuous time optimization problem is reshaped into a discrete multi-phased optimization problem, which yields the identical optimality. After linearizing it, we obtain a linear programming problem that can be solved efficiently. The working strategies of both sensor nodes and wireless energy transfer devices in the pre-normal replenishing stage are also discussed in this paper. The intensive simulations exhibit the dynamic and cyclic working schemes for the entire energy replenishing procedure. Additionally, a way of eliminating "bottleneck" sensor nodes is also developed in this paper.

C-Language Integrated Production System, Version 5.1

NASA Technical Reports Server (NTRS)

Riley, Gary; Donnell, Brian; Ly, Huyen-Anh VU; Culbert, Chris; Savely, Robert T.; Mccoy, Daniel J.; Giarratano, Joseph

1992-01-01

CLIPS 5.1 provides cohesive software tool for handling wide variety of knowledge with support for three different programming paradigms: rule-based, object-oriented, and procedural. Rule-based programming provides representation of knowledge by use of heuristics. Object-oriented programming enables modeling of complex systems as modular components. Procedural programming enables CLIPS to represent knowledge in ways similar to those allowed in such languages as C, Pascal, Ada, and LISP. Working with CLIPS 5.1, one can develop expert-system software by use of rule-based programming only, object-oriented programming only, procedural programming only, or combinations of the three.

Toward high-throughput genotyping: dynamic and automatic software for manipulating large-scale genotype data using fluorescently labeled dinucleotide markers.

PubMed

Li, J L; Deng, H; Lai, D B; Xu, F; Chen, J; Gao, G; Recker, R R; Deng, H W

2001-07-01

To efficiently manipulate large amounts of genotype data generated with fluorescently labeled dinucleotide markers, we developed a Microsoft database management system, named. offers several advantages. First, it accommodates the dynamic nature of the accumulations of genotype data during the genotyping process; some data need to be confirmed or replaced by repeat lab procedures. By using, the raw genotype data can be imported easily and continuously and incorporated into the database during the genotyping process that may continue over an extended period of time in large projects. Second, almost all of the procedures are automatic, including autocomparison of the raw data read by different technicians from the same gel, autoadjustment among the allele fragment-size data from cross-runs or cross-platforms, autobinning of alleles, and autocompilation of genotype data for suitable programs to perform inheritance check in pedigrees. Third, provides functions to track electrophoresis gel files to locate gel or sample sources for any resultant genotype data, which is extremely helpful for double-checking consistency of raw and final data and for directing repeat experiments. In addition, the user-friendly graphic interface of renders processing of large amounts of data much less labor-intensive. Furthermore, has built-in mechanisms to detect some genotyping errors and to assess the quality of genotype data that then are summarized in the statistic reports automatically generated by. The can easily handle >500,000 genotype data entries, a number more than sufficient for typical whole-genome linkage studies. The modules and programs we developed for the can be extended to other database platforms, such as Microsoft SQL server, if the capability to handle still greater quantities of genotype data simultaneously is desired.

Retention and application of Skylab experiences to future programs. [a postflight review of technical programs.

NASA Technical Reports Server (NTRS)

Gillespie, V. G.; Kelly, R. O.

1974-01-01

The problems encountered and special techniques and procedures developed on the Skylab program are described along with the experiences and practical benefits obtained for dissemination and use on future programs. Three major topics are discussed: electrical problems, mechanical problems, and special techniques. Special techniques and procedures are identified that were either developed or refined during the Skylab program. These techniques and procedures came from all manufacturing and test phases of the Skylab program and include both flight and GSE items from component level to sophisticated spaceflight systems.

The MHOST finite element program: 3-D inelastic analysis methods for hot section components. Volume 1: Theoretical manual

NASA Technical Reports Server (NTRS)

Nakazawa, Shohei

1991-01-01

Formulations and algorithms implemented in the MHOST finite element program are discussed. The code uses a novel concept of the mixed iterative solution technique for the efficient 3-D computations of turbine engine hot section components. The general framework of variational formulation and solution algorithms are discussed which were derived from the mixed three field Hu-Washizu principle. This formulation enables the use of nodal interpolation for coordinates, displacements, strains, and stresses. Algorithmic description of the mixed iterative method includes variations for the quasi static, transient dynamic and buckling analyses. The global-local analysis procedure referred to as the subelement refinement is developed in the framework of the mixed iterative solution, of which the detail is presented. The numerically integrated isoparametric elements implemented in the framework is discussed. Methods to filter certain parts of strain and project the element discontinuous quantities to the nodes are developed for a family of linear elements. Integration algorithms are described for linear and nonlinear equations included in MHOST program.

4D Dynamic Required Navigation Performance Final Report

NASA Technical Reports Server (NTRS)

Finkelsztein, Daniel M.; Sturdy, James L.; Alaverdi, Omeed; Hochwarth, Joachim K.

2011-01-01

New advanced four dimensional trajectory (4DT) procedures under consideration for the Next Generation Air Transportation System (NextGen) require an aircraft to precisely navigate relative to a moving reference such as another aircraft. Examples are Self-Separation for enroute operations and Interval Management for in-trail and merging operations. The current construct of Required Navigation Performance (RNP), defined for fixed-reference-frame navigation, is not sufficiently specified to be applicable to defining performance levels of such air-to-air procedures. An extension of RNP to air-to-air navigation would enable these advanced procedures to be implemented with a specified level of performance. The objective of this research effort was to propose new 4D Dynamic RNP constructs that account for the dynamic spatial and temporal nature of Interval Management and Self-Separation, develop mathematical models of the Dynamic RNP constructs, "Required Self-Separation Performance" and "Required Interval Management Performance," and to analyze the performance characteristics of these air-to-air procedures using the newly developed models. This final report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results from this research effort to expand the RNP concept to a dynamic 4D frame of reference.

A six-week neuromuscular training program for competitive junior tennis players.

PubMed

Barber-Westin, Sue D; Hermeto, Alex A; Noyes, Frank R

2010-09-01

This study evaluated the effectiveness of a tennis-specific training program on improving neuromuscular indices in competitive junior players. Tennis is a demanding sport because it requires speed, agility, explosive power, and aerobic conditioning along with the ability to react and anticipate quickly, and there are limited studies that evaluate these indices in young players after a multiweek training program. The program designed for this study implemented the essential components of a previously published neuromuscular training program and also included exercises designed to improve dynamic balance, agility, speed, and strength. Fifteen junior tennis players (10 girls, 5 boys; mean age, 13.0 +/- 1.5 years) who routinely participated in local tournaments and high-school teams participated in the 6-week supervised program. Training was conducted 3 times a week, with sessions lasting 1.5 hours that included a dynamic warm-up, plyometric and jump training, strength training (lower extremity, upper extremity, core), tennis-specific drills, and flexibility. After training, statistically significant improvements and large-to-moderate effect sizes were found in the single-leg triple crossover hop for both legs (p < 0.05), the baseline forehand (p = 0.006) and backhand (p = 0.0008) tests, the service line (p = 0.0009) test, the 1-court suicide (p < 0.0001), the 2-court suicide (p = 0.02), and the abdominal endurance test (p = 0.01). Mean improvements between pretrain and posttrain test sessions were 15% for the single-leg triple crossover hop, 10-11% for the baseline tests, 18% for the service line test, 21% for the 1-court suicide, 10% for the 2-court suicide, and 76% for the abdominal endurance test. No athlete sustained an injury or developed an overuse syndrome as a result of the training program. The results demonstrate that this program is feasible, low in cost, and appears to be effective in improving the majority of neuromuscular indices tested. We accomplished our goal of developing training and testing procedures that could all be performed on the tennis court.

A hybrid downscaling procedure for estimating the vertical distribution of ambient temperature in local scale

NASA Astrophysics Data System (ADS)

Yiannikopoulou, I.; Philippopoulos, K.; Deligiorgi, D.

2012-04-01

The vertical thermal structure of the atmosphere is defined by a combination of dynamic and radiation transfer processes and plays an important role in describing the meteorological conditions at local scales. The scope of this work is to develop and quantify the predictive ability of a hybrid dynamic-statistical downscaling procedure to estimate the vertical profile of ambient temperature at finer spatial scales. The study focuses on the warm period of the year (June - August) and the method is applied to an urban coastal site (Hellinikon), located in eastern Mediterranean. The two-step methodology initially involves the dynamic downscaling of coarse resolution climate data via the RegCM4.0 regional climate model and subsequently the statistical downscaling of the modeled outputs by developing and training site-specific artificial neural networks (ANN). The 2.5ox2.5o gridded NCEP-DOE Reanalysis 2 dataset is used as initial and boundary conditions for the dynamic downscaling element of the methodology, which enhances the regional representivity of the dataset to 20km and provides modeled fields in 18 vertical levels. The regional climate modeling results are compared versus the upper-air Hellinikon radiosonde observations and the mean absolute error (MAE) is calculated between the four grid point values nearest to the station and the ambient temperature at the standard and significant pressure levels. The statistical downscaling element of the methodology consists of an ensemble of ANN models, one for each pressure level, which are trained separately and employ the regional scale RegCM4.0 output. The ANN models are theoretically capable of estimating any measurable input-output function to any desired degree of accuracy. In this study they are used as non-linear function approximators for identifying the relationship between a number of predictor variables and the ambient temperature at the various vertical levels. An insight of the statistically derived input-output transfer functions is obtained by utilizing the ANN weights method, which quantifies the relative importance of the predictor variables in the estimation procedure. The overall downscaling performance evaluation incorporates a set of correlation and statistical measures along with appropriate statistical tests. The hybrid downscaling method presented in this work can be extended to various locations by training different site-specific ANN models and the results, depending on the application, can be used for assisting the understanding of the past, present and future climatology. ____________________________ This research has been co-financed by the European Union and Greek national funds through the Operational Program "Education and Lifelong Learning" of the National Strategic Reference Framework (NSRF) - Research Funding Program: Heracleitus II: Investing in knowledge society through the European Social Fund.

Adaption of a corrector module to the IMP dynamics program

NASA Technical Reports Server (NTRS)

1972-01-01

The corrector module of the RAEIOS program and the IMP dynamics computer program were combined to achieve a date-fitting capability with the more general spacecraft dynamics models of the IMP program. The IMP dynamics program presents models of spacecraft dynamics for satellites with long, flexible booms. The properties of the corrector are discussed and a description is presented of the performance criteria and search logic for parameter estimation. A description is also given of the modifications made to add the corrector to the IMP program. This includes subroutine descriptions, common definitions, definition of input, and a description of output.

Large-scale hydropower system optimization using dynamic programming and object-oriented programming: the case of the Northeast China Power Grid.

PubMed

Li, Ji-Qing; Zhang, Yu-Shan; Ji, Chang-Ming; Wang, Ai-Jing; Lund, Jay R

2013-01-01

This paper examines long-term optimal operation using dynamic programming for a large hydropower system of 10 reservoirs in Northeast China. Besides considering flow and hydraulic head, the optimization explicitly includes time-varying electricity market prices to maximize benefit. Two techniques are used to reduce the 'curse of dimensionality' of dynamic programming with many reservoirs. Discrete differential dynamic programming (DDDP) reduces the search space and computer memory needed. Object-oriented programming (OOP) and the ability to dynamically allocate and release memory with the C++ language greatly reduces the cumulative effect of computer memory for solving multi-dimensional dynamic programming models. The case study shows that the model can reduce the 'curse of dimensionality' and achieve satisfactory results.

76 FR 47518 - Energy Conservation Program: Treatment of “Smart” Appliances in Energy Conservation Standards and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-05

... Conservation Program: Treatment of ``Smart'' Appliances in Energy Conservation Standards and Test Procedures... well as in test procedures used to demonstrate compliance with DOE's standards and qualification as an... development of energy conservation standards and test procedures for DOE's Appliance Standards Program and the...

Handbook of Procedural Guidelines for Implementation of Special Education Curriculum: Critical Skills/Community-Based and Special Education Curriculum Guide.

ERIC Educational Resources Information Center

Riverside County Office of Education, CA. Div. of Special Schools and Services.

The special education procedural handbook and the special education curriculum guide provide guidelines for teachers and other school personnel. The procedural handbook covers the following areas: individual education program process (IEP) and program placement, individual education program team, administrative placements, parent interviews,…

Nouvelles techniques pratiques pour la modelisation du comportement dynamique des systèmes eau-structure

NASA Astrophysics Data System (ADS)

Miquel, Benjamin

The dynamic or seismic behavior of hydraulic structures is, as for conventional structures, essential to assure protection of human lives. These types of analyses also aim at limiting structural damage caused by an earthquake to prevent rupture or collapse of the structure. The particularity of these hydraulic structures is that not only the internal displacements are caused by the earthquake, but also by the hydrodynamic loads resulting from fluid-structure interaction. This thesis reviews the existing complex and simplified methods to perform such dynamic analysis for hydraulic structures. For the complex existing methods, attention is placed on the difficulties arising from their use. Particularly, interest is given in this work on the use of transmitting boundary conditions to simulate the semi infinity of reservoirs. A procedure has been developed to estimate the error that these boundary conditions can introduce in finite element dynamic analysis. Depending on their formulation and location, we showed that they can considerably affect the response of such fluid-structure systems. For practical engineering applications, simplified procedures are still needed to evaluate the dynamic behavior of structures in contact with water. A review of the existing simplified procedures showed that these methods are based on numerous simplifications that can affect the prediction of the dynamic behavior of such systems. One of the main objectives of this thesis has been to develop new simplified methods that are more accurate than those existing. First, a new spectral analysis method has been proposed. Expressions for the fundamental frequency of fluid-structure systems, key parameter of spectral analysis, have been developed. We show that this new technique can easily be implemented in a spreadsheet or program, and that its calculation time is near instantaneous. When compared to more complex analytical or numerical method, this new procedure yields excellent prediction of the dynamic behavior of fluid-structure systems. Spectral analyses ignore the transient and oscillatory nature of vibrations. When such dynamic analyses show that some areas of the studied structure undergo excessive stresses, time history analyses allow a better estimate of the extent of these zones as well as a time notion of these excessive stresses. Furthermore, the existing spectral analyses methods for fluid-structure systems account only for the static effect of higher modes. Thought this can generally be sufficient for dams, for flexible structures the dynamic effect of these modes should be accounted for. New methods have been developed for fluid-structure systems to account for these observations as well as the flexibility of foundations. A first method was developed to study structures in contact with one or two finite or infinite water domains. This new technique includes flexibility of structures and foundations as well as the dynamic effect of higher vibration modes and variations of the levels of the water domains. Extension of this method was performed to study beam structures in contact with fluids. These new developments have also allowed extending existing analytical formulations of the dynamic properties of a dry beam to a new formulation that includes effect of fluid-structure interaction. The method yields a very good estimate of the dynamic behavior of beam-fluid systems or beam like structures in contact with fluid. Finally, a Modified Accelerogram Method (MAM) has been developed to modify the design earthquake into a new accelerogram that directly accounts for the effect of fluid-structure interaction. This new accelerogram can therefore be applied directly to the dry structure (i.e. without water) in order to calculate the dynamic response of the fluid-structure system. This original technique can include numerous parameters that influence the dynamic response of such systems and allows to treat analytically the fluid-structure interaction while keeping the advantages of finite element modeling.

FINITE-STATE APPROXIMATIONS TO DENUMERABLE-STATE DYNAMIC PROGRAMS,

DTIC Science & Technology

AIR FORCE OPERATIONS, LOGISTICS), (*INVENTORY CONTROL, DYNAMIC PROGRAMMING), (*DYNAMIC PROGRAMMING, APPROXIMATION(MATHEMATICS)), INVENTORY CONTROL, DECISION MAKING, STOCHASTIC PROCESSES, GAME THEORY, ALGORITHMS, CONVERGENCE

Advanced crew procedures development techniques

NASA Technical Reports Server (NTRS)

Arbet, J. D.; Benbow, R. L.; Mangiaracina, A. A.; Mcgavern, J. L.; Spangler, M. C.; Tatum, I. C.

1975-01-01

The development of an operational computer program, the Procedures and Performance Program (PPP), is reported which provides a procedures recording and crew/vehicle performance monitoring capability. The PPP provides real time CRT displays and postrun hardcopy of procedures, difference procedures, performance, performance evaluation, and training script/training status data. During post-run, the program is designed to support evaluation through the reconstruction of displays to any point in time. A permanent record of the simulation exercise can be obtained via hardcopy output of the display data, and via magnetic tape transfer to the Generalized Documentation Processor (GDP). Reference procedures data may be transferred from the GDP to the PPP.

INSTRUCTIONAL PROGRAMMING PROCEDURES, A PROGRAMED COURSE IN THE BASIC METHODS AND TECHNIQUES OF PREPARING PROGRAMED INSTRUCTIONAL MATERIALS.

ERIC Educational Resources Information Center

DETERLINE, WILLIAM A.

A PROGRAMED COURSE IN METHODS AND TECHNIQUES OF PREPARING PROGRAMED INSTRUCTIONAL MATERIALS WAS PRESENTED IN THIS DOCUMENT. AN ATTEMPT WAS MADE TO TEACH BASIC PROCEDURES WELL ENOUGH TO PRODUCE AN EMBRYO PROGRAMER AND TO PROVIDE HIM WITH REFERENCES HE WOULD NEED IN ORDER TO PRODUCE PROGRAMS. INCLUDED WERE PROGRAMED INSTRUCTIONS ON PREPARATORY…

77 FR 24341 - Energy Conservation Program: Test Procedures for Residential Clothes Washers; Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-24

... Program: Test Procedures for Residential Clothes Washers; Correction AGENCY: Office of Energy Efficiency... final rule establishing new and amended test procedures for residential clothes washers, published in... Energy (DOE) erroneously referenced the new test procedure, rather than the currently effective test...

77 FR 20291 - Energy Conservation Program: Test Procedures for Residential Clothes Washers; Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-04

... Conservation Program: Test Procedures for Residential Clothes Washers; Correction AGENCY: Office of Energy.... Department of Energy (DOE) is correcting a final rule establishing revised test procedures for residential... factor calculation section of the currently applicable test procedure. DATES: Effective: April 6, 2012...

Information Exchange Procedures. Outcomes Study Procedures. Technical Report No. 66.

ERIC Educational Resources Information Center

Byers, Maureen

The Information Exchange Procedures (IEP) developed by the National Center for Higher Education Management Systems (NCHEMS) are a set of standard definitions and procedures for collecting information about disciplines and student degree programs, outcomes of instructional programs, and general institutional characteristics. A fundamental purpose…

Which Introductory Programming Approach Is Most Suitable for Students: Procedural or Visual Programming?

ERIC Educational Resources Information Center

Eid, Chaker; Millham, Richard

2012-01-01

In this paper, we discuss the visual programming approach to teaching introductory programming courses and then compare this approach with that of procedural programming. The involved cognitive levels of students, as beginning students are introduced to different types of programming concepts, are correlated to the learning processes of…

Dynamic Response Assessment for the MEMS Accelerometer Under Severe Shock Loads

NASA Technical Reports Server (NTRS)

Fan, Mark S.; Shaw, Harry C.

2001-01-01

NASA Goddard Space Flight Center (GSFC) has evaluated the dynamic response of a commercial-off-the-shelf (COTS) microelectromechanical systems (MEMS) device made by Analog Device, Inc. The device is designated as ADXL250 and is designed mainly for sensing dynamic acceleration. It is also used to measure the tilting angle of any system or component from its original level position. The device has been in commercial use (e.g., in automobile airbag deployment system as a dual-axial accelerometer and in the electronic game play-station as a tilting sensor) with success, but NASA needs an in-depth assessment of its performance under severe dynamic shock environments. It was realized while planning this evaluation task that two assessments would be beneficial to NASA's missions: (1) severe dynamic shock response under nominal thermal environments; and (2) general dynamic performance under cryogenic environments. The first evaluation aims at obtaining a good understanding of its micromachined structure within a framework of brittle fracture dynamics, while the second evaluation focuses on the structure integrity under cryogenic temperature conditions. The information we gathered from the manufacturer indicated that the environmental stresses under NASA's evaluation program have been far beyond what the device has experienced with commercial applications, for which the device was designed. Thus NASA needs the outcome of this evaluation in order to make the selection for possible use for its missions. This paper provides details of the first evaluation the dynamic response under severe multi-axial single-pulse shock load. It was performed using finite element tools with nonlinear dynamics procedures.

A system dynamics approach for modeling construction workers' safety attitudes and behaviors.

PubMed

Shin, Mingyu; Lee, Hyun-Soo; Park, Moonseo; Moon, Myunggi; Han, Sangwon

2014-07-01

Construction accidents are caused by an unsafe act (i.e., a person's behavior or activity that deviates from normal accepted safe procedure) and/or an unsafe condition (i.e., a hazard or an unsafe mechanical or physical environment). While there has been dramatic improvement in creating safer construction environments, relatively little is known regarding the elimination of construction workers' unsafe acts. To address this deficiency, this paper aims to develop a system dynamics (SD)-based model of construction workers' mental processes that can help analyze the feedback mechanisms and the resultant dynamics regarding the workers' safety attitudes and safe behaviors. The developed model is applied to examine the effectiveness of three safety improvement policies: incentives for safe behaviors, and increased levels of communication and immersion in accidents. Application of the model verifies the strong potential of the developed model to provide a better understanding of how to eliminate unsafe acts, and to function as a robust test-bed to assess the effectiveness of safety programs or training sessions before their implementation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Population dynamics of minimally cognitive individuals. Part I: Introducing knowledge into the dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmieder, R.W.

The author presents a new approach for modeling the dynamics of collections of objects with internal structure. Based on the fact that the behavior of an individual in a population is modified by its knowledge of other individuals, a procedure for accounting for knowledge in a population of interacting objects is presented. It is assumed that each object has partial (or complete) knowledge of some (or all) other objects in the population. The dynamical equations for the objects are then modified to include the effects of this pairwise knowledge. This procedure has the effect of projecting out what the populationmore » will do from the much larger space of what it could do, i.e., filtering or smoothing the dynamics by replacing the complex detailed physical model with an effective model that produces the behavior of interest. The procedure therefore provides a minimalist approach for obtaining emergent collective behavior. The use of knowledge as a dynamical quantity, and its relationship to statistical mechanics, thermodynamics, information theory, and cognition microstructure are discussed.« less

Procedures for Determining Historical Full Costs. Technical Report 65. Second Edition.

ERIC Educational Resources Information Center

National Association of College and University Business Officers, Washington, DC.

The procedures form the costing component of the National Center for Higher Education Management Systems'"Information Exchange Procedures" (IEP). The IEP are a set of standard definitions and procedures for collecting information about disciplines and student degree programs, outcomes of instructional programs, and general institutional…

76 FR 65631 - Energy Conservation Program: Test Procedures for Microwave Ovens

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-24

... Conservation Program: Test Procedures for Microwave Ovens AGENCY: Office of Energy Efficiency and Renewable... (DOE) has initiated a test procedure rulemaking to develop active mode testing methodologies for... Federal Register a final rule for the microwave oven test procedure rulemaking (July TP repeal final rule...

78 FR 63823 - Energy Conservation Program: Test Procedures for Television Sets

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-25

... Conservation Program: Test Procedures for Television Sets AGENCY: Office of Energy Efficiency and Renewable... Energy (DOE) issued a notice of proposed rulemaking (NOPR) to establish a new test procedure for... additional testing and proposed amendments to the TV test procedure in its March 12, 2013 supplemental notice...

76 FR 50145 - Energy Conservation Program: Test Procedures for Residential Clothes Dryers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-12

... EERE-2011-BT-TP-0054] RIN 1904-AC63 Energy Conservation Program: Test Procedures for Residential...: Request for information. SUMMARY: The U.S. Department of Energy (DOE) has initiated a test procedure... clothes dryer test procedure. DOE will address the issues surrounding testing of automatic cycle...

78 FR 4015 - Energy Conservation Program: Test Procedures for Microwave Ovens

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-18

... Conservation Program: Test Procedures for Microwave Ovens AGENCY: Office of Energy Efficiency and Renewable... Energy (DOE) issued a supplemental notice of proposed rulemaking (SNOPR) to amend the test procedures for microwave ovens. That SNOPR proposed amendments to the DOE test procedure to incorporate provisions from the...

78 FR 62488 - Energy Conservation Program: Compliance Date for the Dehumidifier Test Procedure

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-22

... Conservation Program: Compliance Date for the Dehumidifier Test Procedure AGENCY: Office of Energy Efficiency.... Department of Energy (DOE) proposes to revise the compliance date for the dehumidifier test procedures... manufacturers to test using only the active mode provisions in the test procedure for dehumidifiers currently...

PHYSICAL THERAPY INTERVENTION FOR A FORMER POWER LIFTER AFTER ARTHROSCOPIC MICROFRACTURE PROCEDURE FOR GRADE IV GLENOHUMERAL CHONDRAL DEFECTS

PubMed Central

Sum, Jonathan

2011-01-01

Background: Power lifting places the shoulder complex at risk for injury. Microfracture is a relatively new procedure for chondral defects of the glenohumeral joint and is not well described in the literature. Objectives: The purpose of this case report is to describe the post-operative rehabilitation used with a power lifter who underwent a microfracture procedure to address glenoid and humeral chondral defects, debridement of type I superior labral anterior-posterior lesion, and a subacromial decompression. Case Description: The patient was a 46 year-old male who was evaluated nine weeks status-post arthroscopic microfracture procedure for glenoid and humeral chondral defects, debridement of superior labral anterior-posterior (SLAP) lesion, and subacromial decompression. Rehabilitation consisted of postural education, manual therapy, rotator cuff and scapular strengthening, dynamic stabilization, weightbearing exercises, and weight training over nine weeks (24 sessions). Lifting modifications were addressed. Outcomes: Results of the QuickDASH indicate that activities of daily living (ADLs), work, and sports modules all improved significantly, and the patient was able to return to recreational power lifting with limited discomfort or restrictions. Discussion: A structured post-operative physical therapy treatment program allowed this patient to return to recreational power lifting while restoring independent function for work-related activities and ADLs. PMID:21655454

Southern forest inventory and analysis volume equation user’s guide

Treesearch

Christopher M. Oswalt; Roger C. Conner

2011-01-01

Reliable volume estimation procedures are fundamental to the mission of the Forest Inventory and Analysis (FIA) program. Moreover, public access to FIA program procedures is imperative. Here we present the volume estimation procedures used by the southern FIA program of the U.S. Department of Agriculture Forest Service Southern Research Station. The guide presented...

VSU Campus Alcohol and Drug Policies and Procedures. Revised 1990. Program Design and Questionnaire.

ERIC Educational Resources Information Center

Virginia State Univ., Petersburg.

This document comprises the Virginia State University (VSU) Campus Alcohol and Drug Policies and Procedures booklet; a program design for a VSU drug education, treatment, and prevention program; and a drug and alcohol student survey. The booklet covering policies and procedures contains: a message from the president; a policy statement; a review…

A family of dynamic models for large-eddy simulation

NASA Technical Reports Server (NTRS)

Carati, D.; Jansen, K.; Lund, T.

1995-01-01

Since its first application, the dynamic procedure has been recognized as an effective means to compute rather than prescribe the unknown coefficients that appear in a subgrid-scale model for Large-Eddy Simulation (LES). The dynamic procedure is usually used to determine the nondimensional coefficient in the Smagorinsky (1963) model. In reality the procedure is quite general and it is not limited to the Smagorinsky model by any theoretical or practical constraints. The purpose of this note is to consider a generalized family of dynamic eddy viscosity models that do not necessarily rely on the local equilibrium assumption built into the Smagorinsky model. By invoking an inertial range assumption, it will be shown that the coefficients in the new models need not be nondimensional. This additional degree of freedom allows the use of models that are scaled on traditionally unknown quantities such as the dissipation rate. In certain cases, the dynamic models with dimensional coefficients are simpler to implement, and allow for a 30% reduction in the number of required filtering operations.

12 CFR 168.3 - Security program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 1 2014-01-01 2014-01-01 false Security program. 168.3 Section 168.3 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY SECURITY PROCEDURES § 168.3 Security program. (a) Contents of security program. The security program shall: (1) Establish procedures for...

12 CFR 568.3 - Security program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 6 2014-01-01 2012-01-01 true Security program. 568.3 Section 568.3 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY SECURITY PROCEDURES § 568.3 Security program. (a) Contents of security program. The security program shall: (1) Establish procedures for...

12 CFR 391.3 - Security program.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 5 2013-01-01 2013-01-01 false Security program. 391.3 Section 391.3 Banks and... OF THRIFT SUPERVISION REGULATIONS Security Procedures § 391.3 Security program. (a) Contents of security program. The security program shall: (1) Establish procedures for opening and closing for business...

12 CFR 168.3 - Security program.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 1 2013-01-01 2013-01-01 false Security program. 168.3 Section 168.3 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY SECURITY PROCEDURES § 168.3 Security program. (a) Contents of security program. The security program shall: (1) Establish procedures for...

12 CFR 391.3 - Security program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 5 2014-01-01 2014-01-01 false Security program. 391.3 Section 391.3 Banks and... OF THRIFT SUPERVISION REGULATIONS Security Procedures § 391.3 Security program. (a) Contents of security program. The security program shall: (1) Establish procedures for opening and closing for business...

Structured programming: Principles, notation, procedure

NASA Technical Reports Server (NTRS)

JOST

1978-01-01

Structured programs are best represented using a notation which gives a clear representation of the block encapsulation. In this report, a set of symbols which can be used until binding directives are republished is suggested. Structured programming also allows a new method of procedure for design and testing. Programs can be designed top down, that is, they can start at the highest program plane and can penetrate to the lowest plane by step-wise refinements. The testing methodology also is adapted to this procedure. First, the highest program plane is tested, and the programs which are not yet finished in the next lower plane are represented by so-called dummies. They are gradually replaced by the real programs.

Automated Image Intelligence Adaptive Sensor Management System for High Altitude Long Endurance UAVs in a Dynamic and Anti-Access Area Denial Environment

NASA Astrophysics Data System (ADS)

Kim, Gi Young

The problem we investigate deals with an Image Intelligence (IMINT) sensor allocation schedule for High Altitude Long Endurance UAVs in a dynamic and Anti-Access Area Denial (A2AD) environment. The objective is to maximize the Situational Awareness (SA) of decision makers. The value of SA can be improved in two different ways. First, if a sensor allocated to an Areas of Interest (AOI) detects target activity, then the SA value will be increased. Second, the SA value increases if an AOI is monitored for a certain period of time, regardless of target detections. These values are functions of the sensor allocation time, sensor type and mode. Relatively few studies in the archival literature have been devoted to an analytic, detailed explanation of the target detection process, and AOI monitoring value dynamics. These two values are the fundamental criteria used to choose the most judicious sensor allocation schedule. This research presents mathematical expressions for target detection processes, and shows the monitoring value dynamics. Furthermore, the dynamics of target detection is the result of combined processes between belligerent behavior (target activity) and friendly behavior (sensor allocation). We investigate these combined processes and derive mathematical expressions for simplified cases. These closed form mathematical models can be used for Measures of Effectiveness (MOEs), i.e., target activity detection to evaluate sensor allocation schedules. We also verify these models with discrete event simulations which can also be used to describe more complex systems. We introduce several methodologies to achieve a judicious sensor allocation schedule focusing on the AOI monitoring value. The first methodology is a discrete time integer programming model which provides an optimal solution but is impractical for real world scenarios due to its computation time. Thus, it is necessary to trade off the quality of solution with computation time. The Myopic Greedy Procedure (MGP) is a heuristic which chooses the largest immediate unit time return at each decision epoch. This reduces computation time significantly, but the quality of the solution may be only 95% of optimal (for small size problems). Another alternative is a multi-start random constructive Hybrid Myopic Greedy Procedure (H-MGP), which incorporates stochastic variation in choosing an action at each stage, and repeats it a predetermined number of times (roughly 99.3% of optimal with 1000 repetitions). Finally, the One Stage Look Ahead (OSLA) procedure considers all the 'top choices' at each stage for a temporary time horizon and chooses the best action (roughly 98.8% of optimal with no repetition). Using OSLA procedure, we can have ameliorated solutions within a reasonable computation time. Other important issues discussed in this research are methodologies for the development of input parameters for real world applications.

Operative experience of residents in US general surgery programs: a gap between expectation and experience.

PubMed

Bell, Richard H; Biester, Thomas W; Tabuenca, Arnold; Rhodes, Robert S; Cofer, Joseph B; Britt, L D; Lewis, Frank R

2009-05-01

The purpose of the study was to identify a group of operations which general surgery residency program directors believed residents should be competent to perform by the end of 5 years of training and then ascertain actual resident experience with these procedures during their training. There is concern about the adequacy of training of general surgeons in the United States. The American Board of Surgery and the Association of Program Directors in Surgery undertook a study to determine what operative procedures residency program directors consider to be essential to the practice of general surgery and then we measured the actual operative experience of graduating residents in those procedures, as reported to the Residency Review Committee for Surgery (RRC). An electronic survey was sent to residency program directors at the 254 general surgery programs in the US accredited by the RRC as of spring 2006. The program directors were presented with a list of 300 types of operations. Program directors graded the 300 procedures "A," "B," or "C" using the following criteria: A--graduating general surgery residents should be competent to perform the procedure independently; B--graduating residents should be familiar with the procedure, but not necessarily competent to perform it; and C--graduating residents neither need to be familiar with nor competent to perform the procedure. After ballots were tallied, the actual resident operative experience reported to the RRC by all residents finishing general surgery training in June 2005 was reviewed. One hundred twenty-one of the 300 operations were considered A level procedures by a majority of program directors (PDs). Graduating 2005 US residents (n = 1022) performed only 18 of the 121 A procedures, an average of more than 10 times during residency; 83 of 121 procedures were performed on an average less than 5 times and 31 procedures less than once. For 63 of the 121 procedures, the mode (most commonly reported) experience was 0. In addition, there was significant variation between residents in operative experience for specific procedures. In virtually all cases, the mean reported experience exceeded the mode, suggesting that the mean is a poor measure of typical experience. These data pose important problems for surgical educators. Methods will have to be developed to allow surgeons to reach a basic level of competence in procedures which they are likely to experience only rarely during residency. Even for more commonly performed procedures, the numbers of repetitions are not very robust, stressing the need to determine objectively whether residents are actually achieving basic competency in these operations. Finally, the large variations in experience between individuals in our residency system need to be explored, understood, and remedied.

Improving Safety on the International Space Station: Transitioning to Electronic Emergency Procedure Books on the International Space Station

NASA Technical Reports Server (NTRS)

Carter-Journet, Katrina; Clahoun, Jessica; Morrow, Jason; Duncan, Gary

2012-01-01

The National Aeronautics and Space Administration (NASA) originally designed the International Space Station (ISS) to operate until 2015, but have extended operations until at least 2020. As part of this very dynamic Program, there is an effort underway to simplify the certification of Commercial ]of ]the ]Shelf (COTS) hardware. This change in paradigm allows the ISS Program to take advantage of technologically savvy and commercially available hardware, such as the iPad. The iPad, a line of tablet computers designed and marketed by Apple Inc., was chosen to support this endeavor. The iPad is functional, portable, and could be easily accessed in an emergency situation. The iPad Electronic Flight Bag (EFB), currently approved for use in flight by the Federal Aviation Administration (FAA), is a fraction of the cost of a traditional Class 2 EFB. In addition, the iPad fs ability to use electronic aeronautical data in lieu of paper in route charts and approach plates can cut the annual cost of paper data in half for commercial airlines. ISS may be able to benefit from this type of trade since one of the most important factors considered is information management. Emergency procedures onboard the ISS are currently available to the crew in paper form. Updates to the emergency books can either be launched on an upcoming visiting vehicle such as a Russian Soyuz flight or printed using the onboard ISS printer. In both cases, it is costly to update hardcopy procedures. A new operations concept was proposed to allow for the use of a tablet system that would provide a flexible platform to support space station crew operations. The purpose of the system would be to provide the crew the ability to view and maintain operational data, such as emergency procedures while also allowing Mission Control Houston to update the procedures. The ISS Program is currently evaluating the safety risks associated with the use of iPads versus paper. Paper products can contribute to the flammability risk and require manual updates that take time away from research tasks. The ISS program has recently purchased three iPads for the astronauts and the certification has been approved. The crew is currently using the iPads onboard. The results of this analysis could be used to discern whether the iPad is a viable option for use in emergencies by assessing the risk posture through the development of a quantitative probabilistic risk assessment (PRA).

Cognitive characteristics of learning Java, an object-oriented programming language

NASA Astrophysics Data System (ADS)

White, Garry Lynn

Industry and Academia are moving from procedural programming languages (e.g., COBOL) to object-oriented programming languages, such as Java for the Internet. Past studies in the cognitive aspects of programming have focused primarily on procedural programming languages. Some of the languages used have been Pascal, C, Basic, FORTAN, and COBOL. Object-oriented programming (OOP) represents a new paradigm for computing. Industry is finding that programmers are having difficulty shifting to this new programming paradigm. This instruction in OOP is currently starting in colleges and universities across the country. What are the cognitive aspects for this new OOP language Java? When is a student developmentally ready to handle the cognitive characteristics of the OOP language Java? Which cognitive teaching style is best for this OOP language Java? Questions such as the aforementioned are the focus of this research Such research is needed to improve understanding of the learning process and identify students' difficulties with OOP methods. This can enhance academic teaching and industry training (Scholtz, 1993; Sheetz, 1997; Rosson, 1990). Cognitive development as measured by the Propositional Logic Test, cognitive style as measured by the Hemispheric Mode Indicator, and physical hemispheric dominance as measured by a self-report survey were obtained from thirty-six university students studying Java programming. Findings reveal that physical hemispheric dominance is unrelated to cognitive and programming language variables. However, both procedural and object oriented programming require Piaget's formal operation cognitive level as indicated by the Propositional Logic Test. This is consistent with prior research A new finding is that object oriented programming also requires formal operation cognitive level. Another new finding is that object oriented programming appears to be unrelated to hemispheric cognitive style as indicated by the Hemispheric Mode Indicator (HMI). This research suggests that object oriented programming is hemispheric thinking style friendly, while procedural programming is left hemispheric cognitive style. The conclusion is that cognitive characteristics are not the cause for the difficulty in shifting from procedural to this new programming paradigm of object oriented programming. An alternative possibility to the difficulty is proactive interference. Prior learning of procedural programming makes it harder to learning object oriented programming. Further research is needed to determine if proactive interference is the cause for the difficulty in shifting from procedural programming to object oriented programming.

Rotation in the Dynamic Factor Modeling of Multivariate Stationary Time Series.

ERIC Educational Resources Information Center

Molenaar, Peter C. M.; Nesselroade, John R.

2001-01-01

Proposes a special rotation procedure for the exploratory dynamic factor model for stationary multivariate time series. The rotation procedure applies separately to each univariate component series of a q-variate latent factor series and transforms such a component, initially represented as white noise, into a univariate moving-average.…

Product assurance policies and procedures for flight dynamics software development

NASA Technical Reports Server (NTRS)

Perry, Sandra; Jordan, Leon; Decker, William; Page, Gerald; Mcgarry, Frank E.; Valett, Jon

1987-01-01

The product assurance policies and procedures necessary to support flight dynamics software development projects for Goddard Space Flight Center are presented. The quality assurance and configuration management methods and tools for each phase of the software development life cycles are described, from requirements analysis through acceptance testing; maintenance and operation are not addressed.

Improving L2 Reading Comprehension through Emotionalized Dynamic Assessment Procedures

ERIC Educational Resources Information Center

Abdolrezapour, Parisa

2017-01-01

The paper reports a study on an emotionally-loaded dynamic assessment procedure used with Iranian EFL learners. It focuses on the effect of using emotional intelligence characteristics (based on Goleman's framework) as a tool for motivating learners while performing reading tasks. The study with 50 intermediate learners aged 12-15 used three…

Simplified dynamic analysis to evaluate liquefaction-induced lateral deformation of earth slopes: a computational fluid dynamics approach

NASA Astrophysics Data System (ADS)

Jafarian, Yaser; Ghorbani, Ali; Ahmadi, Omid

2014-09-01

Lateral deformation of liquefiable soil is a cause of much damage during earthquakes, reportedly more than other forms of liquefaction-induced ground failures. Researchers have presented studies in which the liquefied soil is considered as viscous fluid. In this manner, the liquefied soil behaves as non-Newtonian fluid, whose viscosity decreases as the shear strain rate increases. The current study incorporates computational fluid dynamics to propose a simplified dynamic analysis for the liquefaction-induced lateral deformation of earth slopes. The numerical procedure involves a quasi-linear elastic model for small to moderate strains and a Bingham fluid model for large strain states during liquefaction. An iterative procedure is considered to estimate the strain-compatible shear stiffness of soil. The post-liquefaction residual strength of soil is considered as the initial Bingham viscosity. Performance of the numerical procedure is examined by using the results of centrifuge model and shaking table tests together with some field observations of lateral ground deformation. The results demonstrate that the proposed procedure predicts the time history of lateral ground deformation with a reasonable degree of precision.

Vehicle systems: coupled and interactive dynamics analysis

NASA Astrophysics Data System (ADS)

Vantsevich, Vladimir V.

2014-11-01

This article formulates a new direction in vehicle dynamics, described as coupled and interactive vehicle system dynamics. Formalised procedures and analysis of case studies are presented. An analytical consideration, which explains the physics of coupled system dynamics and its consequences for dynamics of a vehicle, is given for several sets of systems including: (i) driveline and suspension of a 6×6 truck, (ii) a brake mechanism and a limited slip differential of a drive axle and (iii) a 4×4 vehicle steering system and driveline system. The article introduces a formal procedure to turn coupled system dynamics into interactive dynamics of systems. A new research direction in interactive dynamics of an active steering and a hybrid-electric power transmitting unit is presented and analysed to control power distribution between the drive axles of a 4×4 vehicle. A control strategy integrates energy efficiency and lateral dynamics by decoupling dynamics of the two systems thus forming their interactive dynamics.

Dynamic simulation modelling of policy responses to reduce alcohol-related harms: rationale and procedure for a participatory approach.

PubMed

Atkinson, Jo-An; O'Donnell, Eloise; Wiggers, John; McDonnell, Geoff; Mitchell, Jo; Freebairn, Louise; Indig, Devon; Rychetnik, Lucie

2017-02-15

Development of effective policy responses to address complex public health problems can be challenged by a lack of clarity about the interaction of risk factors driving the problem, differing views of stakeholders on the most appropriate and effective intervention approaches, a lack of evidence to support commonly implemented and acceptable intervention approaches, and a lack of acceptance of effective interventions. Consequently, political considerations, community advocacy and industry lobbying can contribute to a hotly contested debate about the most appropriate course of action; this can hinder consensus and give rise to policy resistance. The problem of alcohol misuse and its associated harms in New South Wales (NSW), Australia, provides a relevant example of such challenges. Dynamic simulation modelling is increasingly being valued by the health sector as a robust tool to support decision making to address complex problems. It allows policy makers to ask 'what-if' questions and test the potential impacts of different policy scenarios over time, before solutions are implemented in the real world. Participatory approaches to modelling enable researchers, policy makers, program planners, practitioners and consumer representatives to collaborate with expert modellers to ensure that models are transparent, incorporate diverse evidence and perspectives, are better aligned to the decision-support needs of policy makers, and can facilitate consensus building for action. This paper outlines a procedure for embedding stakeholder engagement and consensus building in the development of dynamic simulation models that can guide the development of effective, coordinated and acceptable policy responses to complex public health problems, such as alcohol-related harms in NSW.

Evaluation of dynamical models: dissipative synchronization and other techniques.

PubMed

Aguirre, Luis Antonio; Furtado, Edgar Campos; Tôrres, Leonardo A B

2006-12-01

Some recent developments for the validation of nonlinear models built from data are reviewed. Besides giving an overall view of the field, a procedure is proposed and investigated based on the concept of dissipative synchronization between the data and the model, which is very useful in validating models that should reproduce dominant dynamical features, like bifurcations, of the original system. In order to assess the discriminating power of the procedure, four well-known benchmarks have been used: namely, Duffing-Ueda, Duffing-Holmes, and van der Pol oscillators, plus the Hénon map. The procedure, developed for discrete-time systems, is focused on the dynamical properties of the model, rather than on statistical issues. For all the systems investigated, it is shown that the discriminating power of the procedure is similar to that of bifurcation diagrams--which in turn is much greater than, say, that of correlation dimension--but at a much lower computational cost.

Wisconsin Fire Service Certification Program Procedures.

ERIC Educational Resources Information Center

Pribyl, Paul F.

These procedures for the Wisconsin Fire Service Certification Program provide professional qualification standards for three levels of fire fighter and four levels of fire service instructor. A section on program authority/operations covers program development, the credential review system, and revocation of certification. Requirements for…

A Re-programmable Platform for Dynamic Burn-in Test of Xilinx Virtexll 3000 FPGA for Military and Aerospace Applications

NASA Technical Reports Server (NTRS)

Roosta, Ramin; Wang, Xinchen; Sadigursky, Michael; Tracton, Phil

2004-01-01

Field Programmable Gate Arrays (FPGA) have played increasingly important roles in military and aerospace applications. Xilinx SRAM-based FPGAs have been extensively used in commercial applications. They have been used less frequently in space flight applications due to their susceptibility to single-event upsets. Reliability of these devices in space applications is a concern that has not been addressed. The objective of this project is to design a fully programmable hardware/software platform that allows (but is not limited to) comprehensive static/dynamic burn-in test of Virtex-II 3000 FPGAs, at speed test and SEU test. Conventional methods test very few discrete AC parameters (primarily switching) of a given integrated circuit. This approach will test any possible configuration of the FPGA and any associated performance parameters. It allows complete or partial re-programming of the FPGA and verification of the program by using read back followed by dynamic test. Designers have full control over which functional elements of the FPGA to stress. They can completely simulate all possible types of configurations/functions. Another benefit of this platform is that it allows collecting information on elevation of the junction temperature as a function of gate utilization, operating frequency and functionality. A software tool has been implemented to demonstrate the various features of the system. The software consists of three major parts: the parallel interface driver, main system procedure and a graphical user interface (GUI).

Boolean network identification from perturbation time series data combining dynamics abstraction and logic programming.

PubMed

Ostrowski, M; Paulevé, L; Schaub, T; Siegel, A; Guziolowski, C

2016-11-01

Boolean networks (and more general logic models) are useful frameworks to study signal transduction across multiple pathways. Logic models can be learned from a prior knowledge network structure and multiplex phosphoproteomics data. However, most efficient and scalable training methods focus on the comparison of two time-points and assume that the system has reached an early steady state. In this paper, we generalize such a learning procedure to take into account the time series traces of phosphoproteomics data in order to discriminate Boolean networks according to their transient dynamics. To that end, we identify a necessary condition that must be satisfied by the dynamics of a Boolean network to be consistent with a discretized time series trace. Based on this condition, we use Answer Set Programming to compute an over-approximation of the set of Boolean networks which fit best with experimental data and provide the corresponding encodings. Combined with model-checking approaches, we end up with a global learning algorithm. Our approach is able to learn logic models with a true positive rate higher than 78% in two case studies of mammalian signaling networks; for a larger case study, our method provides optimal answers after 7min of computation. We quantified the gain in our method predictions precision compared to learning approaches based on static data. Finally, as an application, our method proposes erroneous time-points in the time series data with respect to the optimal learned logic models. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

A dynamic model of functioning of a bank

NASA Astrophysics Data System (ADS)

Malafeyev, Oleg; Awasthi, Achal; Zaitseva, Irina; Rezenkov, Denis; Bogdanova, Svetlana

2018-04-01

In this paper, we analyze dynamic programming as a novel approach to solve the problem of maximizing the profits of a bank. The mathematical model of the problem and the description of bank's work is described in this paper. The problem is then approached using the method of dynamic programming. Dynamic programming makes sure that the solutions obtained are globally optimal and numerically stable. The optimization process is set up as a discrete multi-stage decision process and solved with the help of dynamic programming.

Mental health court and assisted outpatient treatment: perceived coercion, procedural justice, and program impact.

PubMed

Munetz, Mark R; Ritter, Christian; Teller, Jennifer L S; Bonfine, Natalie

2014-03-01

Mandated community treatment has been proposed as a mechanism to engage people with severe and persistent mental disorders in treatment. Recently, two approaches to mandate treatment through the courts have been highlighted: assisted outpatient treatment (AOT) and mental health court programs. This study examined levels of perceived coercion, procedural justice, and the impact of the program (mental health court or AOT) among participants in a community treatment system. Data were analyzed from interviews with former AOT participants who were no longer under court supervision (N=17) and with graduates of a mental health court program (N=35). The MacArthur Admission Experience Survey, created to measure perceived coercion, procedural justice, and program impact on hospital admission, was modified to include judges and case managers. Mental health court graduates perceived significantly less coercion and more procedural justice in their interactions with the judge than did AOT participants. No significant difference was found between mental health court and AOT participants in perceptions of procedural justice in interactions with their case managers. Mental health court participants felt more respected and had more positive feelings about the program than did AOT participants. Both mental health courts and AOT programs have potentially coercive aspects. Findings suggest that judges and case managers can affect participants' perceptions of these programs by the degree to which they demonstrate procedural justice, a process that may affect the long-term effects of the programs on individuals.

How quantizable matter gravitates: A practitioner's guide

NASA Astrophysics Data System (ADS)

Schuller, Frederic P.; Witte, Christof

2014-05-01

We present the practical step-by-step procedure for constructing canonical gravitational dynamics and kinematics directly from any previously specified quantizable classical matter dynamics, and then illustrate the application of this recipe by way of two completely worked case studies. Following the same procedure, any phenomenological proposal for fundamental matter dynamics must be supplemented with a suitable gravity theory providing the coefficients and kinematical interpretation of the matter theory, before any of the two theories can be meaningfully compared to experimental data.

7 CFR 220.11 - Reimbursement procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGRICULTURE CHILD NUTRITION PROGRAMS SCHOOL BREAKFAST PROGRAM § 220.11 Reimbursement procedures. (a) To be... by FNS, the Claim for Reimbursement for any month shall include only breakfasts served in that month... Lunch Program and the School Breakfast Program, the State agency or FNSRO, where applicable, may...

7 CFR 220.11 - Reimbursement procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGRICULTURE CHILD NUTRITION PROGRAMS SCHOOL BREAKFAST PROGRAM § 220.11 Reimbursement procedures. (a) To be... by FNS, the Claim for Reimbursement for any month shall include only breakfasts served in that month... Lunch Program and the School Breakfast Program, the State agency or FNSRO, where applicable, may...

48 CFR 619.602 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Procedures. 619.602 Section 619.602 Federal Acquisition Regulations System DEPARTMENT OF STATE SOCIOECONOMIC PROGRAMS SMALL BUSINESS PROGRAMS Certificates of Competency and Determinations of Eligibility 619.602 Procedures. ...

48 CFR 2819.602 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Procedures. 2819.602 Section 2819.602 Federal Acquisition Regulations System DEPARTMENT OF JUSTICE Socioeconomic Programs SMALL BUSINESS PROGRAMS Certificates of Competency and Determinations of Eligibility 2819.602 Procedures. ...

40 CFR 68.52 - Operating procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 2 Prevention Program § 68.52 Operating procedures. (a) The... for safely conducting activities associated with each covered process consistent with the safety information for that process. Operating procedures or instructions provided by equipment manufacturers or...

Procedures to Help Program Offices with Earned Value Management

EPA Pesticide Factsheets

EPA’s Earned Value Management (EVM) Procedures describe the Agency methods for collecting and reporting performance information on major IT investments. The EVM Procedures explain how EPA Program Offices are to receive, organize, analyze, and report cost.

Creating CAD designs and performing their subsequent analysis using opensource solutions in Python

NASA Astrophysics Data System (ADS)

Iakushkin, Oleg O.; Sedova, Olga S.

2018-01-01

The paper discusses the concept of a system that encapsulates the transition from geometry building to strength tests. The solution we propose views the engineer as a programmer who is capable of coding the procedure for working with the modeli.e., to outline the necessary transformations and create cases for boundary conditions. We propose a prototype of such system. In our work, we used: Python programming language to create the program; Jupyter framework to create a single workspace visualization; pythonOCC library to implement CAD; FeniCS library to implement FEM; GMSH and VTK utilities. The prototype is launched on a platform which is a dynamically expandable multi-tenant cloud service providing users with all computing resources on demand. However, the system may be deployed locally for prototyping or work that does not involve resource-intensive computing. To make it possible, we used containerization, isolating the system in a Docker container.

Filament wound data base development, revision 1

NASA Technical Reports Server (NTRS)

Sharp, R. Scott; Braddock, William F.

1985-01-01

The objective was to update the present Space Shuttle Solid Rocket Booster (SRB) baseline reentry aerodynamic data base and to develop a new reentry data base for the filament wound case SRB along with individual protuberance increments. Lockheed's procedures for performing these tasks are discussed. Free fall of the SRBs after separation from the Space Shuttle Launch Vehicle is completely uncontrolled. However, the SRBs must decelerate to a velocity and attitude that is suitable for parachute deployment. To determine the SRB reentry trajectory parameters, including the rate of deceleration and attitude history during free-fall, engineers at Marshall Space Flight Center are using a six-degree-of-freedom computer program to predict dynamic behavior. Static stability aerodynamic coefficients are part of the information required for input into this computer program. Lockheed analyzed the existing reentry aerodynamic data tape (Data Tape 5) for the current steel case SRB. This analysis resulted in the development of Data Tape 7.

A method of automatic control procedures cardiopulmonary resuscitation

NASA Astrophysics Data System (ADS)

Bureev, A. Sh.; Zhdanov, D. S.; Kiseleva, E. Yu.; Kutsov, M. S.; Trifonov, A. Yu.

2015-11-01

The study is to present the results of works on creation of methods of automatic control procedures of cardiopulmonary resuscitation (CPR). A method of automatic control procedure of CPR by evaluating the acoustic data of the dynamics of blood flow in the bifurcation of carotid arteries and the dynamics of air flow in a trachea according to the current guidelines for CPR is presented. Evaluation of the patient is carried out by analyzing the respiratory noise and blood flow in the interspaces between the chest compressions and artificial pulmonary ventilation. The device operation algorithm of automatic control procedures of CPR and its block diagram has been developed.

Operative Landscape at Canadian Neurosurgery Residency Programs.

PubMed

Tso, Michael K; Dakson, Ayoub; Ahmed, Syed Uzair; Bigder, Mark; Elliott, Cameron; Guha, Daipayan; Iorio-Morin, Christian; Kameda-Smith, Michelle; Lavergne, Pascal; Makarenko, Serge; Taccone, Michael S; Wang, Bill; Winkler-Schwartz, Alexander; Sankar, Tejas; Christie, Sean D

2017-07-01

Background Currently, the literature lacks reliable data regarding operative case volumes at Canadian neurosurgery residency programs. Our objective was to provide a snapshot of the operative landscape in Canadian neurosurgical training using the trainee-led Canadian Neurosurgery Research Collaborative. Anonymized administrative operative data were gathered from each neurosurgery residency program from January 1, 2014, to December 31, 2014. Procedures were broadly classified into cranial, spine, peripheral nerve, and miscellaneous procedures. A number of prespecified subspecialty procedures were recorded. We defined the resident case index as the ratio of the total number of operations to the total number of neurosurgery residents in that program. Resident number included both Canadian medical and international medical graduates, and included residents on the neurosurgery service, off-service, or on leave for research or other personal reasons. Overall, there was an average of 1845 operative cases per neurosurgery residency program. The mean numbers of cranial, spine, peripheral nerve, and miscellaneous procedures were 725, 466, 48, and 193, respectively. The nationwide mean resident case indices for cranial, spine, peripheral nerve, and total procedures were 90, 58, 5, and 196, respectively. There was some variation in the resident case indices for specific subspecialty procedures, with some training programs not performing carotid endarterectomy or endoscopic transsphenoidal procedures. This study presents the breadth of neurosurgical training within Canadian neurosurgery residency programs. These results may help inform the implementation of neurosurgery training as the Royal College of Physicians and Surgeons residency training transitions to a competence-by-design curriculum.

UNO DMRG CASCI calculations of effective exchange integrals for m-phenylene-bis-methylene spin clusters

NASA Astrophysics Data System (ADS)

Kawakami, Takashi; Sano, Shinsuke; Saito, Toru; Sharma, Sandeep; Shoji, Mitsuo; Yamada, Satoru; Takano, Yu; Yamanaka, Shusuke; Okumura, Mitsutaka; Nakajima, Takahito; Yamaguchi, Kizashi

2017-09-01

Theoretical examinations of the ferromagnetic coupling in the m-phenylene-bis-methylene molecule and its oligomer were carried out. These systems are good candidates for exchange-coupled systems to investigate strong electronic correlations. We studied effective exchange integrals (J), which indicated magnetic coupling between interacting spins in these species. First, theoretical calculations based on a broken-symmetry single-reference procedure, i.e. the UHF, UMP2, UMP4, UCCSD(T) and UB3LYP methods, were carried out with a GAUSSIAN program code under an SR wave function. From these results, the J value by the UHF method was largely positive because of the strong ferromagnetic spin polarisation effect. The J value by the UCCSD(T) and UB3LYP methods improved an overestimation problem by correcting the dynamical electronic correlation. Next, magnetic coupling among these spins was studied using the CAS-based method of the symmetry-adapted multireference methods procedure. Thus, the UNO DMRG CASCI (UNO, unrestricted natural orbital; DMRG, density matrix renormalised group; CASCI, complete active space configuration interaction) method was mainly employed with a combination of ORCA and BLOCK program codes. DMRG CASCI calculations in valence electron counting, which included all orbitals to full valence CI, provided the most reliable result, and support the UB3LYP method for extended systems.

The International Atomic Energy Agency software package for the analysis of scintigraphic renal dynamic studies: a tool for the clinician, teacher, and researcher.

PubMed

Zaknun, John J; Rajabi, Hossein; Piepsz, Amy; Roca, Isabel; Dondi, Maurizio

2011-01-01

Under the auspices of the International Atomic Energy Agency, a new-generation, platform-independent, and x86-compatible software package was developed for the analysis of scintigraphic renal dynamic imaging studies. It provides nuclear medicine professionals cost-free access to the most recent developments in the field. The software package is a step forward towards harmonization and standardization. Embedded functionalities render it a suitable tool for education, research, and for receiving distant expert's opinions. Another objective of this effort is to allow introducing clinically useful parameters of drainage, including normalized residual activity and outflow efficiency. Furthermore, it provides an effective teaching tool for young professionals who are being introduced to dynamic kidney studies by selected teaching case studies. The software facilitates a better understanding through practically approaching different variables and settings and their effect on the numerical results. An effort was made to introduce instruments of quality assurance at the various levels of the program's execution, including visual inspection and automatic detection and correction of patient's motion, automatic placement of regions of interest around the kidneys, cortical regions, and placement of reproducible background region on both primary dynamic and on postmicturition studies. The user can calculate the differential renal function through 2 independent methods, the integral or the Rutland-Patlak approaches. Standardized digital reports, storage and retrieval of regions of interest, and built-in database operations allow the generation and tracing of full image reports and of numerical outputs. The software package is undergoing quality assurance procedures to verify the accuracy and the interuser reproducibility with the final aim of launching the program for use by professionals and teaching institutions worldwide. Copyright © 2011 Elsevier Inc. All rights reserved.

Enhancing Learners' Emotions in an L2 Context through Emotionalized Dynamic Assessment

ERIC Educational Resources Information Center

Abdolrezapour, Parisa; Tavakoli, Mansoor; Ketabi, Saeed

2013-01-01

The aim of this study was to gain more in-depth understanding of students' emotions in an EFL context by applying dynamic assessment (DA) procedures to the development of learners' emotional intelligence. The study with 50 intermediate learners aged 12-15 used three modalities: a control group, which was taught under institute's normal procedures;…

40 CFR 501.34 - Procedures for withdrawal of State programs.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Procedures for withdrawal of State programs. 501.34 Section 501.34 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SEWAGE SLUDGE STATE SLUDGE MANAGEMENT PROGRAM REGULATIONS Program Approval, Revision and Withdrawal § 501...

A Pilot Program in Adapted Physical Education: Hillsborough High School.

ERIC Educational Resources Information Center

Thompson, Vince

The instructor of an adapted physical education program describes his experiences and suggests guidelines for implementing other programs. Reviewed are such aspects as program orientation, class procedures, identification of student participants, and grading procedures. Objectives, lesson plans and evaluations are presented for the following units…

Dynamic Optimization

NASA Technical Reports Server (NTRS)

Laird, Philip

1992-01-01

We distinguish static and dynamic optimization of programs: whereas static optimization modifies a program before runtime and is based only on its syntactical structure, dynamic optimization is based on the statistical properties of the input source and examples of program execution. Explanation-based generalization is a commonly used dynamic optimization method, but its effectiveness as a speedup-learning method is limited, in part because it fails to separate the learning process from the program transformation process. This paper describes a dynamic optimization technique called a learn-optimize cycle that first uses a learning element to uncover predictable patterns in the program execution and then uses an optimization algorithm to map these patterns into beneficial transformations. The technique has been used successfully for dynamic optimization of pure Prolog.

Practices and Procedures in the Administration of ITV Distance Learning Programs at Selected Institutions in Higher Education.

ERIC Educational Resources Information Center

Koontz, F. R.

The purpose of this study was to obtain current data on practices and procedures in the administration of distance learning programs in the areas of: (1) needs assessment; (2) student demographics; (3) telecourse acquisition procedures and sources; (4) criteria used to evaluate credit telecourses; (5) institutional approval procedures; (6)…

Measuring teacher implementation in delivery of a bullying prevention program: the impact of instructional and procedural adherence and competence on student responsiveness.

PubMed

Goncy, Elizabeth A; Sutherland, Kevin S; Farrell, Albert D; Sullivan, Terri N; Doyle, Sarah T

2015-04-01

Although there is evidence that school-based prevention programs can produce positive effects on students' academic and behavioral functioning, the ability of teachers to sustain high-quality implementation remains an open and vexing question. Because teachers are often the intervention agents in school-based prevention programs, assessing both their adherence to program procedures and their competence in program delivery is critical for ensuring student responsiveness to prevention programs, which in turn may impact their efficacy. The current study assessed treatment fidelity of implementation of the Olweus' Bullying Prevention Program (OBPP) in two urban middle schools. Trained observers completed 280 observations of teachers' delivery of the class meeting component of the OBPP and rated teachers' instructional and procedural adherence and competence of delivery and students' responsiveness. Analyses using multilevel modeling indicated that competence of delivery was significantly related to student responsiveness above and beyond teacher instructional behavior adherence, such that class meetings conducted with higher instructional adherence and procedural competence resulted in higher student responsiveness to the program after controlling for the clustered nature of teachers, and several observation-level and teacher-level covariates. This study highlights the need for strategies to increase teacher use of effective instructional practices and competence with program procedures to enhance the efficacy of prevention programming in schools.

20 CFR 669.120 - How do we administer the NFJP program?

Code of Federal Regulations, 2010 CFR

2010-04-01

... NATIONAL FARMWORKER JOBS PROGRAM UNDER TITLE I OF THE WORKFORCE INVESTMENT ACT Purpose and Definitions....210, we designate grantees using procedures consistent with standard Federal government competitive procedures. We award other grants and contracts using similar competitive procedures. ...

Crew procedures development techniques

NASA Technical Reports Server (NTRS)

Arbet, J. D.; Benbow, R. L.; Hawk, M. L.; Mangiaracina, A. A.; Mcgavern, J. L.; Spangler, M. C.

1975-01-01

The study developed requirements, designed, developed, checked out and demonstrated the Procedures Generation Program (PGP). The PGP is a digital computer program which provides a computerized means of developing flight crew procedures based on crew action in the shuttle procedures simulator. In addition, it provides a real time display of procedures, difference procedures, performance data and performance evaluation data. Reconstruction of displays is possible post-run. Data may be copied, stored on magnetic tape and transferred to the document processor for editing and documentation distribution.

Integration of the virtual 3D model of a control system with the virtual controller

NASA Astrophysics Data System (ADS)

Herbuś, K.; Ociepka, P.

2015-11-01

Nowadays the design process includes simulation analysis of different components of a constructed object. It involves the need for integration of different virtual object to simulate the whole investigated technical system. The paper presents the issues related to the integration of a virtual 3D model of a chosen control system of with a virtual controller. The goal of integration is to verify the operation of an adopted object of in accordance with the established control program. The object of the simulation work is the drive system of a tunneling machine for trenchless work. In the first stage of work was created an interactive visualization of functioning of the 3D virtual model of a tunneling machine. For this purpose, the software of the VR (Virtual Reality) class was applied. In the elaborated interactive application were created adequate procedures allowing controlling the drive system of a translatory motion, a rotary motion and the drive system of a manipulator. Additionally was created the procedure of turning on and off the output crushing head, mounted on the last element of the manipulator. In the elaborated interactive application have been established procedures for receiving input data from external software, on the basis of the dynamic data exchange (DDE), which allow controlling actuators of particular control systems of the considered machine. In the next stage of work, the program on a virtual driver, in the ladder diagram (LD) language, was created. The control program was developed on the basis of the adopted work cycle of the tunneling machine. The element integrating the virtual model of the tunneling machine for trenchless work with the virtual controller is the application written in a high level language (Visual Basic). In the developed application was created procedures responsible for collecting data from the running, in a simulation mode, virtual controller and transferring them to the interactive application, in which is verified the operation of the adopted research object. The carried out work allowed foot the integration of the virtual model of the control system of the tunneling machine with the virtual controller, enabling the verification of its operation.

Guidance Program Assessment Procedures for Elementary and Secondary Schools. Georgia Comprehensive Guidance Series.

ERIC Educational Resources Information Center

Gunderson, Margaret S.; Moore, Earl J.

This manual provides a series of assessment instruments that guidance program planners may adopt or adapt to provide a basis for defining the guidance program, educating others about the program, or planning needed program changes. The assessment procedures are designed to gather information about students' needs and progress from the students,…

48 CFR 26.103 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 26.103 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION SOCIOECONOMIC PROGRAMS OTHER SOCIOECONOMIC PROGRAMS Indian Incentive Program 26.103 Procedures. (a) Contracting officers and... Indian-owned economic enterprise as to its eligibility, unless an interested party challenges its status...

A Stress Inoculation Program for Parents Whose Children Are Undergoing Painful Medical Procedures.

ERIC Educational Resources Information Center

Jay, Susan M.; Elliott, Charles H.

1990-01-01

Compared program efficacy in helping parents cope with children's painful medical procedures. Parents (n=72) of pediatric leukemia patients participated in either stress inoculation program or observed child participating in cognitive behavior therapy. Found parents in stress inoculation program reported lower anxiety scores and higher positive…

Program for Exceptional Children: Regulations and Procedures.

ERIC Educational Resources Information Center

Georgia State Dept. of Education, Atlanta. Office of Instructional Services.

The document reviews state of Georgia and federal law regarding the provision of special education programs for exceptional children and youth and outline procedures for providing those programs. Section I presents a summary of Georgia Chapter 32-6A, particularly the sections which address establishment of other special programs of education;…

78 FR 9651 - Approval and Promulgation of Implementation Plans; Oregon: Heat Smart Program and Enforcement...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-11

... Promulgation of Implementation Plans; Oregon: Heat Smart Program and Enforcement Procedures AGENCY... submission contains revisions to the Heat Smart program and to the enforcement procedures and civil penalties... submission contains additional revisions to the Heat Smart program, along with minor revisions and...

Undergraduate Program Reviews at Brock University. Report of the UPRAC Auditors.

ERIC Educational Resources Information Center

Council of Ontario Universities, Toronto.

Pursuant to the Council of Ontario Universities' procedures for periodic quality reviews of undergraduate programs, auditors examined the policies and programs of Brock University (BU) during 1997. Three departments were selected for audits of their program review procedures: Philosophy, Geography, and Physics; additionally, the Oenology and…

Plotit-method of interactively plotting input data for the vorlax computer program. [computerized aircraft configuration design

NASA Technical Reports Server (NTRS)

Denn, F. M.

1978-01-01

Geometric input plotting to the VORLAX computer program by means of an interactive remote terminal is reported. The software consists of a procedure file and two programs. The programs and procedure file are described and a sample execution is presented.

40 CFR 68.175 - Prevention program/Program 3.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) CHEMICAL ACCIDENT PREVENTION PROVISIONS Risk Management Plan § 68.175 Prevention program/Program... the most recent change that triggered management of change procedures and the date of the most recent review or revision of management of change procedures. (j) The date of the most recent pre-startup review...

Facilitating the exploitation of ERTS imagery using snow enhancement techniques. [geological mapping of New England test area

NASA Technical Reports Server (NTRS)

Wobber, F. J.; Martin, K. R. (Principal Investigator); Amato, R. V.; Leshendok, T.

1974-01-01

The author has identified the following significant results. The procedure for conducting a regional geological mapping program utilizing snow-enhanced ERTS-1 imagery has been summarized. While it is recognized that mapping procedures in geological programs will vary from area to area and from geologist to geologist, it is believed that the procedure tested in this project is applicable over a wide range of mapping programs. The procedure is designed to maximize the utility and value of ERTS-1 imagery and aerial photography within the initial phase of geological mapping programs. Sample products which represent interim steps in the mapping formula (e.g. the ERTS Fracture-Lineament Map) have been prepared. A full account of these procedures and products will be included within the Snow Enhancement Users Manual.

Hatha yoga on body balance

PubMed Central

Prado, Erick Tadeu; Raso, Vagner; Scharlach, Renata Coelho; Kasse, Cristiane Akemi

2014-01-01

Background: A good body balance requires a proper function of vestibular, visual, and somatosensory systems which can be reach with exercise practice and/or yoga. Aim: To determine the effects of a 5-month hatha yoga training program on body balance in young adults. Materials and Methods: This study used a controlled, nonrandomized design, where the experimental group underwent a 5-month training program and were then compared with the control group that had a sedentary lifestyle. A convenience sample of 34 out of 40 men aged 25-55 years old (34.0 ± 0.9) were deemed eligible for this study. They were randomly divided into two groups: Experimental and control groups. Subjects in the experimental group were engaged in 60 min sessions of hatha yoga three times a week for 5 months. We evaluated postural control by measuring the limit of stability and velocity of oscillation (VOS) in three conditions of the balance rehabilitation unit (BRU) and through field procedures (four position, plane, flamingo, hopscotch, and dynamic test). Results: We observed differences (P < 0.05) in postintervention scores between the groups regardless of BRU parameters and field procedures (except for flamingo) even after adjusting for preintervention scores, suggesting that these changes were induced by hatha yoga training. The partial eta squared on BRU parameters ranged from 0.78 (VOS1)-0.97 (COP2), and from 0.00 (flamingo)-0.94 (four position) for the field procedures. Conclusions: Our results provide substantial evidence that postural control in healthy young adults can be improved through practicing hatha yoga. PMID:25035623

Addressing Dynamic Issues of Program Model Checking

NASA Technical Reports Server (NTRS)

Lerda, Flavio; Visser, Willem

2001-01-01

Model checking real programs has recently become an active research area. Programs however exhibit two characteristics that make model checking difficult: the complexity of their state and the dynamic nature of many programs. Here we address both these issues within the context of the Java PathFinder (JPF) model checker. Firstly, we will show how the state of a Java program can be encoded efficiently and how this encoding can be exploited to improve model checking. Next we show how to use symmetry reductions to alleviate some of the problems introduced by the dynamic nature of Java programs. Lastly, we show how distributed model checking of a dynamic program can be achieved, and furthermore, how dynamic partitions of the state space can improve model checking. We support all our findings with results from applying these techniques within the JPF model checker.

Challenges of CPAS Flight Testing

NASA Technical Reports Server (NTRS)

Ray, Eric S.; Morris, Aaron L.

2011-01-01

The Crew Exploration Vehicle Parachute Assembly System (CPAS) is being designed to land the Orion Crew Module (CM) at a safe rate of descent at splashdown via a series of Drogue, Pilot, and Main parachutes. Because Orion is considerably larger and heavier than Apollo, many of the flight test techniques developed during the Apollo program must be modified. The Apollo program had a dedicated C-133 aircraft, which was modified to allow a simple airdrop of "boilerplate" flight test vehicles. However, the CPAS program must use either commercial or military assets with minimal modifications to airframes or procedures. Conceptual envelopes from 2-Degree Of Freedom trajectories are presented for several existing and novel architectures. Ideally, the technique would deliver a representative capsule shape to the desired altitude and dynamic pressure at test initiation. However, compromises must be made on the characteristics of trajectories or the fidelity of test articles to production hardware. Most of the tests to date have used traditional pallet and weight tub or missile-shaped test vehicles. New test vehicles are being designed to better incorporate Orion structural components and deploy parachutes in a more representative fashion. The first attempt to test a capsule-shaped vehicle failed due to unexpected events while setting up the test condition through a series of complex procedures. In order to avoid the loss of another expensive test article which will delay the program, simpler deployment methods are being examined and more positive control of the vehicle will be maintained. Existing challenges include interfacing with parent aircraft, separating test vehicles, achieving test conditions, and landing within limited test ranges. All these challenges must be met within cost and schedule limits.

Dynamic systems and the role of evaluation: The case of the Green Communities project.

PubMed

Anzoise, Valentina; Sardo, Stefania

2016-02-01

The crucial role evaluation can play in the co-development of project design and its implementation will be addressed through the analysis of a case study, the Green Communities (GC) project, funded by the Italian Ministry of Environment within the EU Interregional Operational Program (2007-2013) "Renewable Energy and Energy Efficiency". The project's broader goals included an attempt to trigger a change in Italian local development strategies, especially for mountain and inland areas, which would be tailored to the real needs of communities, and based on a sustainable exploitation and management of the territorial assets. The goal was not achieved, and this paper addresses the issues of how GC could have been more effective in fostering a vision of change, and which design adaptations and evaluation procedures would have allowed the project to better cope with the unexpected consequences and resistances it encountered. The conclusions drawn are that projects should be conceived, designed and carried out as dynamic systems, inclusive of a dynamic and engaged evaluation enabling the generation of feedbacks loops, iteratively interpreting the narratives and dynamics unfolding within the project, and actively monitoring the potential of various relationships among project participants for generating positive social change. Copyright © 2015 Elsevier Ltd. All rights reserved.

RMP Guidance for Chemical Distributors - Chapter 8: Emergency Response Program

EPA Pesticide Factsheets

Depending on the level of processes at your facility, part 68 may require an emergency response program: an emergency response plan, emergency response equipment procedures, employee training, and procedures to ensure the program is up-to-date.

Analysis of structural dynamic data from Skylab. Volume 1: Technical discussion

NASA Technical Reports Server (NTRS)

Demchak, L.; Harcrow, H.

1976-01-01

A compendium of Skylab structural dynamics analytical and test programs is presented. These programs are assessed to identify lessons learned from the structural dynamic prediction effort and to provide guidelines for future analysts and program managers of complex spacecraft systems. It is a synopsis of the structural dynamic effort performed under the Skylab Integration contract and specifically covers the development, utilization, and correlation of Skylab Dynamic Orbital Models.

Dynamic alarm response procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, J.; Gordon, P.; Fitch, K.

2006-07-01

The Dynamic Alarm Response Procedure (DARP) system provides a robust, Web-based alternative to existing hard-copy alarm response procedures. This paperless system improves performance by eliminating time wasted looking up paper procedures by number, looking up plant process values and equipment and component status at graphical display or panels, and maintenance of the procedures. Because it is a Web-based system, it is platform independent. DARP's can be served from any Web server that supports CGI scripting, such as Apache{sup R}, IIS{sup R}, TclHTTPD, and others. DARP pages can be viewed in any Web browser that supports Javascript and Scalable Vector Graphicsmore » (SVG), such as Netscape{sup R}, Microsoft Internet Explorer{sup R}, Mozilla Firefox{sup R}, Opera{sup R}, and others. (authors)« less

A Manual Control Test for the Detection and Deterrence of Impaired Drivers

NASA Technical Reports Server (NTRS)

Stein, A. C.; Allen, R. W.; Jex, H. R.

1984-01-01

A brief manual control test and a decision strategy were developed, laboratory tested, and field validated which provide a means for detecting human operator impairment from alcohol or other drugs. The test requires the operator to stabilize progressively unstable controlled element dynamics. Control theory and experimental data verify that the human operator's control ability on this task is constrained by basic cybernetic characteristics, and that task performance is reliably affected by impairment effects on these characteristics. Assessment of human operator control ability is determined by a statistically based decision strategy. The operator is allowed several chances to exceed a preset pass criterion. Procedures are described for setting the pass criterion based on individual ability and a desired unimpaired failure rate. These procedures were field tested with apparatus installed in automobiles that were designed to discourage drunk drivers from operating their vehicles. This test program demonstrated that the control task and detection strategy could be applied in a practical setting to screen human operators for impairment in their basic cybernetic skills.

TAS: A Transonic Aircraft/Store flow field prediction code

NASA Technical Reports Server (NTRS)

Thompson, D. S.

1983-01-01

A numerical procedure has been developed that has the capability to predict the transonic flow field around an aircraft with an arbitrarily located, separated store. The TAS code, the product of a joint General Dynamics/NASA ARC/AFWAL research and development program, will serve as the basis for a comprehensive predictive method for aircraft with arbitrary store loadings. This report described the numerical procedures employed to simulate the flow field around a configuration of this type. The validity of TAS code predictions is established by comparison with existing experimental data. In addition, future areas of development of the code are outlined. A brief description of code utilization is also given in the Appendix. The aircraft/store configuration is simulated using a mesh embedding approach. The computational domain is discretized by three meshes: (1) a planform-oriented wing/body fine mesh, (2) a cylindrical store mesh, and (3) a global Cartesian crude mesh. This embedded mesh scheme enables simulation of stores with fins of arbitrary angular orientation.

Bellman's GAP--a language and compiler for dynamic programming in sequence analysis.

PubMed

Sauthoff, Georg; Möhl, Mathias; Janssen, Stefan; Giegerich, Robert

2013-03-01

Dynamic programming is ubiquitous in bioinformatics. Developing and implementing non-trivial dynamic programming algorithms is often error prone and tedious. Bellman's GAP is a new programming system, designed to ease the development of bioinformatics tools based on the dynamic programming technique. In Bellman's GAP, dynamic programming algorithms are described in a declarative style by tree grammars, evaluation algebras and products formed thereof. This bypasses the design of explicit dynamic programming recurrences and yields programs that are free of subscript errors, modular and easy to modify. The declarative modules are compiled into C++ code that is competitive to carefully hand-crafted implementations. This article introduces the Bellman's GAP system and its language, GAP-L. It then demonstrates the ease of development and the degree of re-use by creating variants of two common bioinformatics algorithms. Finally, it evaluates Bellman's GAP as an implementation platform of 'real-world' bioinformatics tools. Bellman's GAP is available under GPL license from http://bibiserv.cebitec.uni-bielefeld.de/bellmansgap. This Web site includes a repository of re-usable modules for RNA folding based on thermodynamics.

Multimodal Logistics Network Design over Planning Horizon through a Hybrid Meta-Heuristic Approach

NASA Astrophysics Data System (ADS)

Shimizu, Yoshiaki; Yamazaki, Yoshihiro; Wada, Takeshi

Logistics has been acknowledged increasingly as a key issue of supply chain management to improve business efficiency under global competition and diversified customer demands. This study aims at improving a quality of strategic decision making associated with dynamic natures in logistics network optimization. Especially, noticing an importance to concern with a multimodal logistics under multiterms, we have extended a previous approach termed hybrid tabu search (HybTS). The attempt intends to deploy a strategic planning more concretely so that the strategic plan can link to an operational decision making. The idea refers to a smart extension of the HybTS to solve a dynamic mixed integer programming problem. It is a two-level iterative method composed of a sophisticated tabu search for the location problem at the upper level and a graph algorithm for the route selection at the lower level. To keep efficiency while coping with the resulting extremely large-scale problem, we invented a systematic procedure to transform the original linear program at the lower-level into a minimum cost flow problem solvable by the graph algorithm. Through numerical experiments, we verified the proposed method outperformed the commercial software. The results indicate the proposed approach can make the conventional strategic decision much more practical and is promising for real world applications.

7 CFR 225.13 - Appeal procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 4 2014-01-01 2014-01-01 false Appeal procedures. 225.13 Section 225.13 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SUMMER FOOD SERVICE PROGRAM State Agency Provisions § 225.13 Appeal procedures...

7 CFR 225.13 - Appeal procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 4 2011-01-01 2011-01-01 false Appeal procedures. 225.13 Section 225.13 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SUMMER FOOD SERVICE PROGRAM State Agency Provisions § 225.13 Appeal procedures...

7 CFR 225.13 - Appeal procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 4 2012-01-01 2012-01-01 false Appeal procedures. 225.13 Section 225.13 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SUMMER FOOD SERVICE PROGRAM State Agency Provisions § 225.13 Appeal procedures...

7 CFR 225.13 - Appeal procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 4 2013-01-01 2013-01-01 false Appeal procedures. 225.13 Section 225.13 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SUMMER FOOD SERVICE PROGRAM State Agency Provisions § 225.13 Appeal procedures...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

Undergraduate Program Reviews at the University of Ottawa. Report of the UPRAC Auditors.

ERIC Educational Resources Information Center

Council of Ontario Universities, Toronto.

Pursuant to the Council of Ontario Universities' procedures for periodic quality reviews of undergraduate programs, auditors examined the policies and programs of the University of Ottawa (UO) during 1997. The English, Chemistry, and Physiotherapy departments were selected for audits of their program review procedures; the Environmental Studies…

7 CFR 614.3 - Decisions subject to informal appeal procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Soil and Water Conservation Program; (iv) Water Bank Program; (v) Watershed Protection and Flood... CONSERVATION SERVICE, DEPARTMENT OF AGRICULTURE CONSERVATION OPERATIONS NRCS APPEAL PROCEDURES § 614.3... technical determinations made with respect to: (1) Conservation programs and regulatory requirements...

7 CFR 614.3 - Decisions subject to informal appeal procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Soil and Water Conservation Program; (iv) Water Bank Program; (v) Watershed Protection and Flood... CONSERVATION SERVICE, DEPARTMENT OF AGRICULTURE CONSERVATION OPERATIONS NRCS APPEAL PROCEDURES § 614.3... technical determinations made with respect to: (1) Conservation programs and regulatory requirements...

Numerical solution of quadratic matrix equations for free vibration analysis of structures

NASA Technical Reports Server (NTRS)

Gupta, K. K.

1975-01-01

This paper is concerned with the efficient and accurate solution of the eigenvalue problem represented by quadratic matrix equations. Such matrix forms are obtained in connection with the free vibration analysis of structures, discretized by finite 'dynamic' elements, resulting in frequency-dependent stiffness and inertia matrices. The paper presents a new numerical solution procedure of the quadratic matrix equations, based on a combined Sturm sequence and inverse iteration technique enabling economical and accurate determination of a few required eigenvalues and associated vectors. An alternative procedure based on a simultaneous iteration procedure is also described when only the first few modes are the usual requirement. The employment of finite dynamic elements in conjunction with the presently developed eigenvalue routines results in a most significant economy in the dynamic analysis of structures.

40 CFR 76.15 - Test methods and procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 17 2012-07-01 2012-07-01 false Test methods and procedures. 76.15 Section 76.15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.15 Test methods and procedures. (a) The...

32 CFR 319.7 - Special procedures: Medical records.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 2 2012-07-01 2012-07-01 false Special procedures: Medical records. 319.7 Section 319.7 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY OF DEFENSE (CONTINUED) PRIVACY PROGRAM DEFENSE INTELLIGENCE AGENCY PRIVACY PROGRAM § 319.7 Special procedures: Medical...

32 CFR 319.7 - Special procedures: Medical records.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 2 2014-07-01 2014-07-01 false Special procedures: Medical records. 319.7 Section 319.7 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY OF DEFENSE (CONTINUED) PRIVACY PROGRAM DEFENSE INTELLIGENCE AGENCY PRIVACY PROGRAM § 319.7 Special procedures: Medical...

32 CFR 319.7 - Special procedures: Medical records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false Special procedures: Medical records. 319.7 Section 319.7 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY OF DEFENSE (CONTINUED) PRIVACY PROGRAM DEFENSE INTELLIGENCE AGENCY PRIVACY PROGRAM § 319.7 Special procedures: Medical...

40 CFR 76.15 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Test methods and procedures. 76.15 Section 76.15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.15 Test methods and procedures. (a) The...

40 CFR 76.15 - Test methods and procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Test methods and procedures. 76.15 Section 76.15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.15 Test methods and procedures. (a) The...

40 CFR 76.15 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Test methods and procedures. 76.15 Section 76.15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.15 Test methods and procedures. (a) The...

40 CFR 76.15 - Test methods and procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Test methods and procedures. 76.15 Section 76.15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.15 Test methods and procedures. (a) The...

75 FR 71596 - Energy Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

... Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for Commercial Refrigeration Equipment AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION... amendments to its test procedure for commercial refrigeration equipment (CRE). The amendments would update...

42 CFR 416.172 - Adjustments to national payment rates.

Code of Federal Regulations, 2013 CFR

2013-10-01

... program and beneficiary coinsurance amounts if the procedure for which anesthesia is planned is discontinued after the induction of anesthesia or after the procedure is started; (2) One-half of the full program and beneficiary coinsurance amounts if the procedure for which anesthesia is planned is...

Efficient placement of structural dynamics sensors on the space station

NASA Technical Reports Server (NTRS)

Lepanto, Janet A.; Shepard, G. Dudley

1987-01-01

System identification of the space station dynamic model will require flight data from a finite number of judiciously placed sensors on it. The placement of structural dynamics sensors on the space station is a particularly challenging problem because the station will not be deployed in a single mission. Given that the build-up sequence and the final configuration for the space station are currently undetermined, a procedure for sensor placement was developed using the assembly flights 1 to 7 of the rephased dual keel space station as an example. The procedure presented approaches the problem of placing the sensors from an engineering, as opposed to a mathematical, point of view. In addition to locating a finite number of sensors, the procedure addresses the issues of unobserved structural modes, dominant structural modes, and the trade-offs involved in sensor placement for space station. This procedure for sensor placement will be applied to revised, and potentially more detailed, finite element models of the space station configuration and assembly sequence.

Fels-Rand: an Xlisp-Stat program for the comparative analysis of data under phylogenetic uncertainty.

PubMed

Blomberg, S

2000-11-01

Currently available programs for the comparative analysis of phylogenetic data do not perform optimally when the phylogeny is not completely specified (i.e. the phylogeny contains polytomies). Recent literature suggests that a better way to analyse the data would be to create random trees from the known phylogeny that are fully-resolved but consistent with the known tree. A computer program is presented, Fels-Rand, that performs such analyses. A randomisation procedure is used to generate trees that are fully resolved but whose structure is consistent with the original tree. Statistics are then calculated on a large number of these randomly-generated trees. Fels-Rand uses the object-oriented features of Xlisp-Stat to manipulate internal tree representations. Xlisp-Stat's dynamic graphing features are used to provide heuristic tools to aid in analysis, particularly outlier analysis. The usefulness of Xlisp-Stat as a system for phylogenetic computation is discussed. Available from the author or at http://www.uq.edu.au/~ansblomb/Fels-Rand.sit.hqx. Xlisp-Stat is available from http://stat.umn.edu/~luke/xls/xlsinfo/xlsinfo.html. s.blomberg@abdn.ac.uk

Rotorcraft research testing in the National Full-Scale Aerodynamics Complex at NASA Ames Research Center

NASA Technical Reports Server (NTRS)

Warmbrodt, W.; Smith, C. A.; Johnson, W.

1985-01-01

The unique capabilities of the National Full-Scale Aerodynamics Complex (NFAC) for testing rotorcraft systems are described. The test facilities include the 40- by 80-Foot Wind Tunnel, the 80- by 120-Foot Wind Tunnel, and the Outdoor Aerodynamic Research Facility. The Ames 7- by 10-Foot Subsonic Wind Tunnel is also used in support of the rotor research programs conducted in the NFAC. Detailed descriptions of each of the facilities, with an emphasis on helicopter rotor test capability, are presented. The special purpose rotor test equipment used in conducting helicopter research is reviewed. Test rigs to operate full-scale helicopter main rotors, helicopter tail rotors, and tilting prop-rotors are available, as well as full-scale and small-scale rotor systems for use in various research programs. The test procedures used in conducting rotor experiments are discussed together with representative data obtained from previous test programs. Specific examples are given for rotor performance, loads, acoustics, system interactions, dynamic and aeroelastic stability, and advanced technology and prototype demonstration models.

30 CFR 795.5 - Grant application procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

....5 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SMALL OPERATOR ASSISTANCE PERMANENT REGULATORY PROGRAM-SMALL OPERATOR ASSISTANCE PROGRAM § 795.5 Grant application procedures. A State intending to administer a Small Operator Assistance Program under a grant from...

7 CFR 614.3 - Decisions subject to informal appeal procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Innovation Grants, (E) Ground and Surface Water Conservation Program, (F) Klamath Basin Program, and (G... CONSERVATION SERVICE, DEPARTMENT OF AGRICULTURE CONSERVATION OPERATIONS NRCS APPEAL PROCEDURES § 614.3... technical determinations made with respect to: (1) Conservation programs and regulatory requirements...

7 CFR 614.3 - Decisions subject to informal appeal procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Innovation Grants, (E) Ground and Surface Water Conservation Program, (F) Klamath Basin Program, and (G... CONSERVATION SERVICE, DEPARTMENT OF AGRICULTURE CONSERVATION OPERATIONS NRCS APPEAL PROCEDURES § 614.3... technical determinations made with respect to: (1) Conservation programs and regulatory requirements...

10 CFR 712.1 - Purpose.

Code of Federal Regulations, 2011 CFR

2011-01-01

... HUMAN RELIABILITY PROGRAM Establishment of and Procedures for the Human Reliability Program General Provisions § 712.1 Purpose. This part establishes the policies and procedures for a Human Reliability Program... judgment and reliability may be impaired by physical or mental/personality disorders, alcohol abuse, use of...

Revitalizing an Established Program for Adult Learners

ERIC Educational Resources Information Center

Rice, Alison, Ed.

2007-01-01

Deliberately introducing change into an established English language program, in which faculty, students, and administrators are comfortable with courses and procedures, is unsettling and often costly. Why, then, would overworked program directors, coordinators, and faculty decide to overhaul their curricula, testing procedures, and academic…

40 CFR 610.10 - Program purpose.

Code of Federal Regulations, 2013 CFR

2013-07-01

... DEVICES Test Procedures and Evaluation Criteria General Provisions § 610.10 Program purpose. (a) The... standardized procedures, the performance of various retrofit devices applicable to automobiles for which fuel... statistical analysis of data from vehicle tests, the evaluation program will determine the effects on fuel...

40 CFR 610.10 - Program purpose.

Code of Federal Regulations, 2014 CFR

2014-07-01

... DEVICES Test Procedures and Evaluation Criteria General Provisions § 610.10 Program purpose. (a) The... standardized procedures, the performance of various retrofit devices applicable to automobiles for which fuel... statistical analysis of data from vehicle tests, the evaluation program will determine the effects on fuel...

40 CFR 610.10 - Program purpose.

Code of Federal Regulations, 2011 CFR

2011-07-01

... DEVICES Test Procedures and Evaluation Criteria General Provisions § 610.10 Program purpose. (a) The... standardized procedures, the performance of various retrofit devices applicable to automobiles for which fuel... statistical analysis of data from vehicle tests, the evaluation program will determine the effects on fuel...

40 CFR 610.10 - Program purpose.

Code of Federal Regulations, 2012 CFR

2012-07-01

... DEVICES Test Procedures and Evaluation Criteria General Provisions § 610.10 Program purpose. (a) The... standardized procedures, the performance of various retrofit devices applicable to automobiles for which fuel... statistical analysis of data from vehicle tests, the evaluation program will determine the effects on fuel...

Matched-pair analyses of resting and dynamic morphology between Monarc and TVT-O procedures by ultrasound.

PubMed

Yang, Jenn-Ming; Yang, Shwu-Huey; Huang, Wen-Chen; Tzeng, Chii-Ruey

2013-07-01

To determine morphologic differences between Monarc and TVT-O procedures in axial and coronal planes by three- and four-dimensional (3D and 4D) ultrasound. Retrospective chart audits and ultrasound analyses were conducted on 128 women who had undergone either Monarc or TVT-O procedures for urodynamic stress incontinence. Thirty matched pairs of the two successful procedures were randomly selected and compared. Matched variables were age, parity, body mass index, cesarean status, menopausal status, and primary surgeries. Six-month postoperative 3D and 4D ultrasound results obtained at rest, on straining, and during coughing in these 60 women were analyzed. Assessed ultrasound parameters included the axial tape urethral distance (aTUD), axial central urethral echolucent area (aUCEA), axial tape angle (aTA), and coronal tape angle (cTA), all of which were measured at three equidistant points along the tapes. Paired t-tests were used to compare differences in ultrasound parameters between women after the two procedures and a P value <0.004 was considered significant after Bonferroni correction. At rest, women subjected to Monarc procedures had a significantly wider aTA at one-fourth of the tape and a wider cTA at one-, two-, and three-fourths of the tape than did those subjected to TVT-O procedures. There were no significant differences in other resting ultrasound parameters between these two procedures. Additionally, after both procedures women had comparable straining and coughing ultrasound manifestations as well as respective dynamic changes. Despite flatter resting tape angulations in women following Monarc procedures, both Monarc and TVT-O tapes had equivalent dynamic patterns and changes assessed by 4D ultrasound. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

MD Simulations of P-Type ATPases in a Lipid Bilayer System.

PubMed

Autzen, Henriette Elisabeth; Musgaard, Maria

2016-01-01

Molecular dynamics (MD) simulation is a computational method which provides insight on protein dynamics with high resolution in both space and time, in contrast to many experimental techniques. MD simulations can be used as a stand-alone method to study P-type ATPases as well as a complementary method aiding experimental studies. In particular, MD simulations have proved valuable in generating and confirming hypotheses relating to the structure and function of P-type ATPases. In the following, we describe a detailed practical procedure on how to set up and run a MD simulation of a P-type ATPase embedded in a lipid bilayer using software free of use for academics. We emphasize general considerations and problems typically encountered when setting up simulations. While full coverage of all possible procedures is beyond the scope of this chapter, we have chosen to illustrate the MD procedure with the Nanoscale Molecular Dynamics (NAMD) and the Visual Molecular Dynamics (VMD) software suites.

The surgical experience of general surgery residents: an analysis of the applicability of the specialty program in General and Digestive Surgery.

PubMed

Targarona Soler, Eduardo Ma; Jover Navalon, Jose Ma; Gutierrez Saiz, Javier; Turrado Rodríguez, Víctor; Parrilla Paricio, Pascual

2015-03-01

Residents in our country have achieved a homogenous surgical training by following a structured residency program. This is due to the existence of specific training programs for each specialty. The current program, approved in 2007, has a detailed list of procedures that a surgeon should have performed in order to complete training. The aim of this study is to analyze the applicability of the program with regard to the number of procedures performed during the residency period. A data collection form was designed that included the list of procedures from the program of the specialty; it was sent in April 2014 to all hospitals with accredited residency programs. In September 2014 the forms were analysed, and a general descriptive study was performed; a subanalysis according to the resident's sex and Autonomous region was also performed. The number of procedures performed according to the number of residents in the different centers was also analyzed. The survey was sent to 117 hospitals with accredited programs, which included 190 resident places. A total of 91 hospitals responded (53%). The training offered adapts in general to the specialty program. The total number of procedures performed in the different sub-areas, in laparoscopic and emergency surgery is correct or above the number recommended by the program, with the exception of esophageal-gastric and hepatobiliary surgery. The sub-analysis according to Autonomous region did not show any significant differences in the total number of procedures, however, there were significant differences in endocrine surgery (P=.001) and breast surgery (P=.042). A total of 55% of residents are female, with no significant differences in distribution in Autonomous regions. However, female surgeons operate more than their male counterparts during the residency period (512±226 vs. 625±244; P<.01). The number of residents in the hospital correlates with the number of procedures performed; the residents with more procedures trained in hospitals where there were less residents (669±237 vs. 527±209; P=.004). The surgical activity performed by spanish surgeons is adequate to the specialty program, except in hepatobiliary and esophageal-gastric surgery. The distribution is homogeneous in the different autonomous regions, although there are differences that depend on the number and sex the of residents in each hospital. This information is essential to evaluate the quality of the specialty program and to design new training programs. Copyright © 2015 AEC. Publicado por Elsevier España, S.L.U. All rights reserved.

Handbook of Procedures for the Graduation Program 2007-2008

ERIC Educational Resources Information Center

British Columbia Ministry of Education, 2007

2007-01-01

This 2007-2008 manual, "Handbook of Procedures for the Graduation Program," has been approved by the British Columbia Minister of Education on July 18, 2007 for the purpose of setting out graduation requirements. The handbook outlines procedures for efficiently sharing student data between schools and the Ministry of Education, and…

28 CFR 550.44 - Procedures for arranging drug counseling.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Procedures for arranging drug counseling... MANAGEMENT DRUG PROGRAMS Drug Services (Urine Surveillance and Counseling for Sentenced Inmates in Contract CTCs) § 550.44 Procedures for arranging drug counseling. The contract center staff shall hold a program...

28 CFR 550.44 - Procedures for arranging drug counseling.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 28 Judicial Administration 2 2011-07-01 2011-07-01 false Procedures for arranging drug counseling... MANAGEMENT DRUG PROGRAMS Drug Services (Urine Surveillance and Counseling for Sentenced Inmates in Contract CTCs) § 550.44 Procedures for arranging drug counseling. The contract center staff shall hold a program...

28 CFR 550.44 - Procedures for arranging drug counseling.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 28 Judicial Administration 2 2013-07-01 2013-07-01 false Procedures for arranging drug counseling... MANAGEMENT DRUG PROGRAMS Drug Services (Urine Surveillance and Counseling for Sentenced Inmates in Contract CTCs) § 550.44 Procedures for arranging drug counseling. The contract center staff shall hold a program...

28 CFR 550.44 - Procedures for arranging drug counseling.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 28 Judicial Administration 2 2014-07-01 2014-07-01 false Procedures for arranging drug counseling... MANAGEMENT DRUG PROGRAMS Drug Services (Urine Surveillance and Counseling for Sentenced Inmates in Contract CTCs) § 550.44 Procedures for arranging drug counseling. The contract center staff shall hold a program...

28 CFR 550.44 - Procedures for arranging drug counseling.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 28 Judicial Administration 2 2012-07-01 2012-07-01 false Procedures for arranging drug counseling... MANAGEMENT DRUG PROGRAMS Drug Services (Urine Surveillance and Counseling for Sentenced Inmates in Contract CTCs) § 550.44 Procedures for arranging drug counseling. The contract center staff shall hold a program...

The Use of Cloze Procedure in Adult Literacy Programs.

ERIC Educational Resources Information Center

Rosenkranz, Catherine

The study was designed to determine whether cloze procedure could be used in adult literacy programs for students reading at or above the fourth grade level by investigating the procedure's: acceptability for the students, utility in matching students to reading material, and substitutability for standardized tests. Eighty-five Rhode Island…

32 CFR 319.7 - Special procedures: Medical records.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 2 2013-07-01 2013-07-01 false Special procedures: Medical records. 319.7... (CONTINUED) PRIVACY PROGRAM DEFENSE INTELLIGENCE AGENCY PRIVACY PROGRAM § 319.7 Special procedures: Medical records. Medical records, requested pursuant to § 319.5 of this part, will be disclosed to the requester...

34 CFR 674.19 - Fiscal procedures and records.

Code of Federal Regulations, 2011 CFR

2011-07-01

... EDUCATION, DEPARTMENT OF EDUCATION FEDERAL PERKINS LOAN PROGRAM General Provisions § 674.19 Fiscal procedures and records. (a) Fiscal procedures. (1) In administering its Federal Perkins Loan program, an... Federal Perkins Loan Fund cash assets do not fall below the amount of Fund cash assets deposited in those...

32 CFR 319.7 - Special procedures: Medical records.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 2 2011-07-01 2011-07-01 false Special procedures: Medical records. 319.7... (CONTINUED) PRIVACY PROGRAM DEFENSE INTELLIGENCE AGENCY PRIVACY PROGRAM § 319.7 Special procedures: Medical records. Medical records, requested pursuant to § 319.5 of this part, will be disclosed to the requester...

34 CFR 675.49 - Procedures and records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false Procedures and records. 675.49 Section 675.49 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF POSTSECONDARY EDUCATION, DEPARTMENT OF EDUCATION FEDERAL WORK-STUDY PROGRAMS Work-Colleges Program § 675.49 Procedures and records. In...

77 FR 26471 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs: 6-acetylmorphine (6-AM...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-04

... 2105-AE14 Procedures for Transportation Workplace Drug and Alcohol Testing Programs: 6-acetylmorphine... Department is amending certain provisions of its drug testing procedures for 6-acetylmorphine (6-AM), a... (email). SUPPLEMENTARY INFORMATION: Background For its drug testing regulation, the Department of...

A Web-based Multimedia Program Before Colonoscopy Increased Knowledge and Decreased Anxiety, Sedation Requirement, and Procedure Time.

PubMed

Parker, Siddhartha; Zipursky, Jonathan; Ma, Helen; Baumblatt, Geri-Lynn; Siegel, Corey A

2018-07-01

Assess the impact of a web-based multimedia patient engagement program on patient anxiety, perception and knowledge about the colonoscopy in addition to procedure outcomes. The success of patients coming for a colonoscopy for colorectal cancer screening is dependent in part on patients' understanding of the preparation and of the procedure. Patients were randomized to use either our institution's standard preprocedure colonoscopy packet or a web-based multimedia patient engagement program (Emmi Solutions) before their scheduled procedure. On the day of colonoscopy, all participants completed a survey including questions to assess knowledge and perception of colonoscopy, in addition to the State Trait Anxiety Inventory. We also collected procedure data including medication doses and procedure time. Patients in the experimental group correctly answered knowledge questions (82%) more often than the control group (74%) (P=0.0003). More than half (58%) of patients in the experimental group felt this intervention reduced their anxiety about the procedure, and the State Trait Anxiety Inventory anxiety score was lower in the experimental group (P=0.026). Patients who viewed the program required less midazolam (3.66 vs. 4.46 mg, P=0.0035) and total procedure time was shorter (24.8 vs. 29 min, P=0.024). A web-based multimedia patient engagement program watched before colonoscopy decreased patient anxiety, medication requirements, and procedure time while increasing knowledge. This intervention could help patients understand and feel more comfortable about colonoscopy leading to increased screening rates while increasing efficiency and decreasing recovery time.

PSYCHE: An Object-Oriented Approach to Simulating Medical Education

PubMed Central

Mullen, Jamie A.

1990-01-01

Traditional approaches to computer-assisted instruction (CAI) do not provide realistic simulations of medical education, in part because they do not utilize heterogeneous knowledge bases for their source of domain knowledge. PSYCHE, a CAI program designed to teach hypothetico-deductive psychiatric decision-making to medical students, uses an object-oriented implementation of an intelligent tutoring system (ITS) to model the student, domain expert, and tutor. It models the transactions between the participants in complex transaction chains, and uses heterogeneous knowledge bases to represent both domain and procedural knowledge in clinical medicine. This object-oriented approach is a flexible and dynamic approach to modeling, and represents a potentially valuable tool for the investigation of medical education and decision-making.

Eigenspace techniques for active flutter suppression

NASA Technical Reports Server (NTRS)

Garrard, W. L.

1982-01-01

Mathematical models to be used in the control system design were developed. A computer program, which takes aerodynamic and structural data for the ARW-2 aircraft and converts these data into state space models suitable for use in modern control synthesis procedures, was developed. Reduced order models of inboard and outboard control surface actuator dynamics and a second order vertical wind gust model were developed. An analysis of the rigid body motion of the ARW-2 was conducted. The deletion of the aerodynamic lag states in the rigid body modes resulted in more accurate values for the eigenvalues associated with the plunge and pitch modes than were obtainable if the lag states were retained.

Development of a Free-to-Roll Transonic Test Capability (Invited)

NASA Technical Reports Server (NTRS)

Capone, F. J.; Owens, D. B.; Hall, R. M.

2003-01-01

As part of the NASA/Navy Abrupt Wing Stall Program, a relatively low-cost, rapid-access wind-tunnel free-to-roll rig was developed. This rig combines the use of conventional models and test apparatuses to evaluate both transonic performance and wing-drop/rock tendencies in a single tunnel entry. A description of the test hardware as well as a description of the experimental procedures is given. The free-to-roll test rig has been used successfully to assess the static and dynamic characteristics of three different configurations--two configurations that exhibit uncommanded lateral motions, (pre-production F/A-18E and AV-8B), and one that did not (F/A-18C).

Cosmology from group field theory formalism for quantum gravity.

PubMed

Gielen, Steffen; Oriti, Daniele; Sindoni, Lorenzo

2013-07-19

We identify a class of condensate states in the group field theory (GFT) formulation of quantum gravity that can be interpreted as macroscopic homogeneous spatial geometries. We then extract the dynamics of such condensate states directly from the fundamental quantum GFT dynamics, following the procedure used in ordinary quantum fluids. The effective dynamics is a nonlinear and nonlocal extension of quantum cosmology. We also show that any GFT model with a kinetic term of Laplacian type gives rise, in a semiclassical (WKB) approximation and in the isotropic case, to a modified Friedmann equation. This is the first concrete, general procedure for extracting an effective cosmological dynamics directly from a fundamental theory of quantum geometry.

State Education Department: Security over Pupil Evaluation Program and Program Evaluation Test Materials Needs Improvement. Report 91-S-2.

ERIC Educational Resources Information Center

New York State Office of the Comptroller, Albany.

Findings of an audit of the New York State Education Department's procedures to maintain security over Pupil Evaluation Program (PEP) and Program Evaluation Test (PET) examination materials are presented in this report. The audit sought to determine whether the department's security procedures adequately prevented unauthorized access to exam…

Procedures for Making Grant Awards under Three Department of Education Discretionary Grant Programs. Report.

ERIC Educational Resources Information Center

General Accounting Office, Washington, DC.

Procedures are described for selecting field readers and awarding grants under the Women's Educational Equity Act Program, National Institute of Education, and Talent Search Programs. Information is provided for each on (1) the legislation, regulations, policy, and program directives that govern the grant award process; (2) how and by whom funding…

FORTRAN IV Program to Determine the Proper Sequence of Records in a Datafile

ERIC Educational Resources Information Center

Jones, Michael P.; Yoshida, Roland K.

1975-01-01

This FORTRAN IV program executes an essential editing procedure which determines whether a datafile contains an equal number of records (cards) per case which are also in the intended sequential order. The program which requires very little background in computer programming is designed primarily for the user of packaged statistical procedures.…

Program Evaluation of a Special Education Day School for Conduct Problem Adolescents.

ERIC Educational Resources Information Center

Maher, Charles A.

1981-01-01

Describes a procedure for program evaluation of a special education day school. The procedure enables a program evaluator to: (1) identify priority evaluation information needs of a school staff, (2) involve those persons in evaluation design and implementation, and (3) determine the utility of the evaluation for program decision-making purposes.…

The essential role of reconfiguration capabilities in the implementation of HIV-related health information exchanges.

PubMed

Steward, Wayne T; Koester, Kimberly A; Collins, Shane P; Maiorana, Andre; Myers, Janet J

2012-10-01

To understand the dynamic capabilities that enabled the six demonstration projects of the Information Technology Networks of Care Initiative to implement health information exchanges (HIEs) tailored to their local HIV epidemics and regional care systems. We conducted 111 semi-structured interviews with project staff and information technology (IT) specialists associated with the demonstration projects, staff from community-based organizations and public health agencies collaborating in the design and implementation of the HIEs, and providers who used each HIE. The dynamic capability framework guided analyses. In the context of a HIE, the framework's components include information systems (the actual technological exchange systems and capacity to update them), absorptive capacity (the ability to implement an operating HIE), reconfiguration capacity (the ability to adapt workflows and clinical practices in response to a HIE), and organizational size and human resources (characteristics likely to affect a clinic's ability to respond). Across the projects, we found evidence for the importance of three dynamic capabilities: information systems, reconfiguration capacity, and organizational size and human resources. However, of these three, reconfiguration capacity was the most salient. Implementation outcomes at all six of the projects were shaped substantially by the degree of attention dedicated to reworking procedures and practices so that HIE usage became routine. Electronic information exchange offers the promise of improved coordination of care. However, implementation of HIEs goes beyond programing and hardware installation challenges, and requires close attention to the needs of the HIEs end-users. Providers need to discern value from a HIE because their active participation is essential to ensuring that clinic and agency practices and procedures are reconfigured to incorporate new systems into daily work processes. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Transient responses of phosphoric acid fuel cell power plant system. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Lu, Cheng-Yi

1983-01-01

An analytical and computerized study of the steady state and transient response of a phosphoric acid fuel cell (PAFC) system was completed. Parametric studies and sensitivity analyses of the PAFC system's operation were accomplished. Four non-linear dynamic models of the fuel cell stack, reformer, shift converters, and heat exchangers were developed based on nonhomogeneous non-linear partial differential equations, which include the material, component, energy balance, and electrochemical kinetic features. Due to a lack of experimental data for the dynamic response of the components only the steady state results were compared with data from other sources, indicating reasonably good agreement. A steady state simulation of the entire system was developed using, nonlinear ordinary differential equations. The finite difference method and trial-and-error procedures were used to obtain a solution. Using the model, a PAFC system, that was developed under NASA Grant, NCC3-17, was improved through the optimization of the heat exchanger network. Three types of cooling configurations for cell plates were evaluated to obtain the best current density and temperature distributions. The steady state solutions were used as the initial conditions in the dynamic model. The transient response of a simplified PAFC system, which included all of the major components, subjected to a load change was obtained. Due to the length of the computation time for the transient response calculations, analysis on a real-time computer was not possible. A simulation of the real-time calculations was developed on a batch type computer. The transient response characteristics are needed for the optimization of the design and control of the whole PAFC system. All of the models, procedures and simulations were programmed in Fortran and run on IBM 370 computers at Cleveland State University and the NASA Lewis Research Center.

A method for the dynamic management of genetic variability in dairy cattle

PubMed Central

Colleau, Jean-Jacques; Moureaux, Sophie; Briend, Michèle; Bechu, Jérôme

2004-01-01

According to the general approach developed in this paper, dynamic management of genetic variability in selected populations of dairy cattle is carried out for three simultaneous purposes: procreation of young bulls to be further progeny-tested, use of service bulls already selected and approval of recently progeny-tested bulls for use. At each step, the objective is to minimize the average pairwise relationship coefficient in the future population born from programmed matings and the existing population. As a common constraint, the average estimated breeding value of the new population, for a selection goal including many important traits, is set to a desired value. For the procreation of young bulls, breeding costs are additionally constrained. Optimization is fully analytical and directly considers matings. Corresponding algorithms are presented in detail. The efficiency of these procedures was tested on the current Norman population. Comparisons between optimized and real matings, clearly showed that optimization would have saved substantial genetic variability without reducing short-term genetic gains. PMID:15231230

Parallel cascade selection molecular dynamics for efficient conformational sampling and free energy calculation of proteins

NASA Astrophysics Data System (ADS)

Kitao, Akio; Harada, Ryuhei; Nishihara, Yasutaka; Tran, Duy Phuoc

2016-12-01

Parallel Cascade Selection Molecular Dynamics (PaCS-MD) was proposed as an efficient conformational sampling method to investigate conformational transition pathway of proteins. In PaCS-MD, cycles of (i) selection of initial structures for multiple independent MD simulations and (ii) conformational sampling by independent MD simulations are repeated until the convergence of the sampling. The selection is conducted so that protein conformation gradually approaches a target. The selection of snapshots is a key to enhance conformational changes by increasing the probability of rare event occurrence. Since the procedure of PaCS-MD is simple, no modification of MD programs is required; the selections of initial structures and the restart of the next cycle in the MD simulations can be handled with relatively simple scripts with straightforward implementation. Trajectories generated by PaCS-MD were further analyzed by the Markov state model (MSM), which enables calculation of free energy landscape. The combination of PaCS-MD and MSM is reported in this work.

Adaptive Critic-based Neurofuzzy Controller for the Steam Generator Water Level

NASA Astrophysics Data System (ADS)

Fakhrazari, Amin; Boroushaki, Mehrdad

2008-06-01

In this paper, an adaptive critic-based neurofuzzy controller is presented for water level regulation of nuclear steam generators. The problem has been of great concern for many years as the steam generator is a highly nonlinear system showing inverse response dynamics especially at low operating power levels. Fuzzy critic-based learning is a reinforcement learning method based on dynamic programming. The only information available for the critic agent is the system feedback which is interpreted as the last action the controller has performed in the previous state. The signal produced by the critic agent is used alongside the backpropagation of error algorithm to tune online conclusion parts of the fuzzy inference rules. The critic agent here has a proportional-derivative structure and the fuzzy rule base has nine rules. The proposed controller shows satisfactory transient responses, disturbance rejection and robustness to model uncertainty. Its simple design procedure and structure, nominates it as one of the suitable controller designs for the steam generator water level control in nuclear power plant industry.

Teaching and assessing technical proficiency in surgical subspecialty fellowships.

PubMed

Gearhart, Susan L; Wang, Ming-Hsien; Gilson, Marta M; Chen, Belinda; Kern, David E

2012-01-01

To determine how programs are teaching and assessing procedural skills, and their perceived success. Cross-sectional survey. Accreditation Council for Graduate Medical Education (ACGME) approved training programs in pediatric urology and colorectal surgery. Program directors and recent graduates (2007-2009). Thirty-nine program directors (60%), and 57 graduates (64%) responded; 89.5% of graduates and 94.9% of program directors felt training occurred successfully for the procedures that trainees were performing in their present practice. Nearly 90% of trainees and all program directors reported that there was no formal assessment of procedural competency at the beginning of training, although 66.7% of program directors reported that trainees were assessed "informally." Both program directors and trainees reported dialogue with faculty was the most frequent method used in preparing for operative procedures. Other methods (textbook/atlas, journals, web-based programs, videos) were used less frequently. Program directors with shorter tenure were more likely to use web-based and video methods; younger trainees were less likely to use textbooks/atlases. Faculty feedback on clinical decision-making and postprocedural review were perceived by both program directors and trainees as the most effective assessment methods for improving performance; however, trainees were more likely than program directors to report that postprocedure reviews were not included in their training (15.8% vs 9%, p = 0.045). Patient outcomes, written feedback from peers, and self-assessment were included in most programs, but valued less. Simulation was used in only about half the programs and was valued more highly by trainees than program directors (p = 0.011). Training in procedural proficiency was viewed as successful by both program directors and graduates. Dialogue with, assessment by, and feedback from faculty were frequently used and most valued; stressing the importance of the facilitator role of faculty in the education of the trainee. These findings provide guidance for the development of newer methods of teaching and assessment. Copyright © 2012 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Training of Personnel to Work with Young Children in India.

ERIC Educational Resources Information Center

Kahalakdina, M.

1984-01-01

Describes recruitment procedures for child care workers in India. Includes a description of training programs, training needs and approaches, and curriculum and training procedures. Monitoring and evaluation of child welfare programs are discussed. Appendices include descriptions of and norms for training programs. (AS)

75 FR 34625 - Administrative Remedy Program: Exception to Initial Filing Procedures

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-18

... Remedy Program: Exception to Initial Filing Procedures AGENCY: Bureau of Prisons, Justice. ACTION... Administrative Remedy Program to add an exception to initial filing of Administrative Remedy appeals at the institution level. The exception will state that formal administrative remedy requests regarding initial...

7 CFR 215.10 - Reimbursement procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SPECIAL MILK PROGRAM FOR CHILDREN § 215.10 Reimbursement procedures. (a... agency administers any combination of the Child Nutrition Programs, the SFA shall be able to use a common...

7 CFR 215.10 - Reimbursement procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SPECIAL MILK PROGRAM FOR CHILDREN § 215.10 Reimbursement procedures. (a... agency administers any combination of the Child Nutrition Programs, the SFA shall be able to use a common...

7 CFR 215.10 - Reimbursement procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SPECIAL MILK PROGRAM FOR CHILDREN § 215.10 Reimbursement procedures. (a... agency administers any combination of the Child Nutrition Programs, the SFA shall be able to use a common...

7 CFR 215.10 - Reimbursement procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SPECIAL MILK PROGRAM FOR CHILDREN § 215.10 Reimbursement procedures. (a... agency administers any combination of the Child Nutrition Programs, the SFA shall be able to use a common...

7 CFR 215.10 - Reimbursement procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS SPECIAL MILK PROGRAM FOR CHILDREN § 215.10 Reimbursement procedures. (a... agency administers any combination of the Child Nutrition Programs, the SFA shall be able to use a common...

TETRA-COM: a comprehensive SPSS program for estimating the tetrachoric correlation.

PubMed

Lorenzo-Seva, Urbano; Ferrando, Pere J

2012-12-01

We provide an SPSS program that implements descriptive and inferential procedures for estimating tetrachoric correlations. These procedures have two main purposes: (1) bivariate estimation in contingency tables and (2) constructing a correlation matrix to be used as input for factor analysis (in particular, the SPSS FACTOR procedure). In both cases, the program computes accurate point estimates, as well as standard errors and confidence intervals that are correct for any population value. For purpose (1), the program computes the contingency table together with five other measures of association. For purpose (2), the program checks the positive definiteness of the matrix, and if it is found not to be Gramian, performs a nonlinear smoothing procedure at the user's request. The SPSS syntax, a short manual, and data files related to this article are available as supplemental materials from brm.psychonomic-journals.org/content/supplemental.

Ecological Research Division Theoretical Ecology Program. [Contains abstracts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-10-01

This report presents the goals of the Theoretical Ecology Program and abstracts of research in progress. Abstracts cover both theoretical research that began as part of the terrestrial ecology core program and new projects funded by the theoretical program begun in 1988. Projects have been clustered into four major categories: Ecosystem dynamics; landscape/scaling dynamics; population dynamics; and experiment/sample design.

INDDGO: Integrated Network Decomposition & Dynamic programming for Graph Optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Groer, Christopher S; Sullivan, Blair D; Weerapurage, Dinesh P

2012-10-01

It is well-known that dynamic programming algorithms can utilize tree decompositions to provide a way to solve some \\emph{NP}-hard problems on graphs where the complexity is polynomial in the number of nodes and edges in the graph, but exponential in the width of the underlying tree decomposition. However, there has been relatively little computational work done to determine the practical utility of such dynamic programming algorithms. We have developed software to construct tree decompositions using various heuristics and have created a fast, memory-efficient dynamic programming implementation for solving maximum weighted independent set. We describe our software and the algorithms wemore » have implemented, focusing on memory saving techniques for the dynamic programming. We compare the running time and memory usage of our implementation with other techniques for solving maximum weighted independent set, including a commercial integer programming solver and a semi-definite programming solver. Our results indicate that it is possible to solve some instances where the underlying decomposition has width much larger than suggested by the literature. For certain types of problems, our dynamic programming code runs several times faster than these other methods.« less

Computer program system for dynamic simulation and stability analysis of passive and actively controlled spacecraft. Volume 1. Theory

NASA Technical Reports Server (NTRS)

Bodley, C. S.; Devers, D. A.; Park, C. A.

1975-01-01

A theoretical development and associated digital computer program system is presented. The dynamic system (spacecraft) is modeled as an assembly of rigid and/or flexible bodies not necessarily in a topological tree configuration. The computer program system may be used to investigate total system dynamic characteristics including interaction effects between rigid and/or flexible bodies, control systems, and a wide range of environmental loadings. Additionally, the program system may be used for design of attitude control systems and for evaluation of total dynamic system performance including time domain response and frequency domain stability analyses. Volume 1 presents the theoretical developments including a description of the physical system, the equations of dynamic equilibrium, discussion of kinematics and system topology, a complete treatment of momentum wheel coupling, and a discussion of gravity gradient and environmental effects. Volume 2, is a program users' guide and includes a description of the overall digital program code, individual subroutines and a description of required program input and generated program output. Volume 3 presents the results of selected demonstration problems that illustrate all program system capabilities.

User's manual for RAD/EQUIL/1973: A general purpose radiation transport program

NASA Technical Reports Server (NTRS)

Nicolet, W. E.

1973-01-01

A procedure is described for implementing the RAD/EQUIL/1973 program, and instructions are given which allow the program input to be prepared, the output to be interpreted, the operating procedures identified which must be followed, and the meaning of the error messages to be understood. The structure of the program is described through a verbal description, a FORTRAN variables list, and a listing of the program.

Experimental Verification of Buffet Calculation Procedure Using Unsteady PSP

NASA Technical Reports Server (NTRS)

Panda, Jayanta

2016-01-01

Typically a limited number of dynamic pressure sensors are employed to determine the unsteady aerodynamic forces on large, slender aerospace structures. The estimated forces are known to be very sensitive to the number of the dynamic pressure sensors and the details of the integration scheme. This report describes a robust calculation procedure, based on frequency-specific correlation lengths, that is found to produce good estimation of fluctuating forces from a few dynamic pressure sensors. The validation test was conducted on a flat panel, placed on the floor of a wind tunnel, and was subjected to vortex shedding from a rectangular bluff-body. The panel was coated with fast response Pressure Sensitive Paint (PSP), which allowed time-resolved measurements of unsteady pressure fluctuations on a dense grid of spatial points. The first part of the report describes the detail procedure used to analyze the high-speed, PSP camera images. The procedure includes steps to reduce contamination by electronic shot noise, correction for spatial non-uniformities, and lamp brightness variation, and finally conversion of fluctuating light intensity to fluctuating pressure. The latter involved applying calibration constants from a few dynamic pressure sensors placed at selective points on the plate. Excellent comparison in the spectra, coherence and phase, calculated via PSP and dynamic pressure sensors validated the PSP processing steps. The second part of the report describes the buffet validation process, for which the first step was to use pressure histories from all PSP points to determine the "true" force fluctuations. In the next step only a selected number of pixels were chosen as "virtual sensors" and a correlation-length based buffet calculation procedure was applied to determine "modeled" force fluctuations. By progressively decreasing the number of virtual sensors it was observed that the present calculation procedure was able to make a close estimate of the "true" unsteady forces only from four sensors. It is believed that the present work provides the first validation of the buffet calculation procedure which has been used for the development of many space vehicles.

New methods of measuring and calibrating robots

NASA Astrophysics Data System (ADS)

Janocha, Hartmut; Diewald, Bernd

1995-10-01

ISO 9283 and RIA R15.05 define industrial robot parameters which are applied to compare the efficiency of different robots. Hitherto, however, no suitable measurement systems have been available. ICAROS is a system which combines photogrammetrical procedures with an inertial navigation system. For the first time, this combination allows the high-precision static and dynamic measurement of the position as well as of the orientation of the robot endeffector. Thus, not only the measuring data for the determination of all industrial robot parameters can be acquired. By integration of a new over-all-calibration procedure, ICAROS also allows the reduction of the absolute robot pose errors to the range of its repeatability. The integration of both system components as well as measurement and calibration results are presented in this paper, using a six-axes robot as example. A further approach also presented here takes into consideration not only the individual robot errors but also the tolerances of workpieces. This allows the adjustment of off-line programs of robots based on inexact or idealized CAD data in any pose. Thus the robot position which is defined relative to the workpiece to be processed, is achieved as required. This includes the possibility to transfer teached robot programs to other devices without additional expenditure. The adjustment is based on the measurement of the robot position using two miniaturized CCD cameras mounted near the endeffector which are carried along by the robot during the correction phase. In the area viewed by both cameras, the robot position is determined in relation to prominent geometry elements, e.g. lines or holes. The scheduled data to be compared therewith can either be calculated in modern off-line programming systems during robot programming, or they can be determined at the so-called master robot if a transfer of the robot program is desired.

7 CFR 272.7 - Procedures for program administration in Alaska.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Procedures for program administration in Alaska. 272.7 Section 272.7 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE FOOD STAMP AND FOOD DISTRIBUTION PROGRAM REQUIREMENTS FOR PARTICIPATING...

78 FR 39587 - Uniform Procedures for State Highway Safety Grant Programs

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-02

... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 23 CFR Parts 1200... 2127-AL29 Uniform Procedures for State Highway Safety Grant Programs AGENCY: National Highway Traffic... governing the implementation of State highway safety grant programs as amended by the Moving Ahead for...

Individualized Foreign Language Program.

ERIC Educational Resources Information Center

Joint School District No. 1, West Bend, WI.

A summary of project objectives, procedures, and dissemination is developed in this report of work initiated in June 1968. Programs in French, German, and Spanish for students in junior and senior high schools are evaluated with special reference to attitudes, aptitude, achievement, and program management. A final section reviews procedures and…

23 CFR 1200.10 - Application.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Application. 1200.10 Section 1200.10 Highways NATIONAL... PROCEDURES FOR STATE HIGHWAY SAFETY PROGRAMS UNIFORM PROCEDURES FOR STATE HIGHWAY SAFETY PROGRAMS Application, Approval, and Funding of the Highway Safety Program § 1200.10 Application. Each fiscal year, a State's...

28 CFR 94.31 - Application procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Terrorism Victim Expense Reimbursement Program Program Administration § 94.31 Application procedures. (a) To... paragraph (a) of this Section, in cases involving incidents of terrorism preceding the establishment of this...

28 CFR 94.31 - Application procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Terrorism Victim Expense Reimbursement Program Program Administration § 94.31 Application procedures. (a) To... paragraph (a) of this Section, in cases involving incidents of terrorism preceding the establishment of this...

28 CFR 94.31 - Application procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Terrorism Victim Expense Reimbursement Program Program Administration § 94.31 Application procedures. (a) To... paragraph (a) of this Section, in cases involving incidents of terrorism preceding the establishment of this...

28 CFR 94.31 - Application procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Terrorism Victim Expense Reimbursement Program Program Administration § 94.31 Application procedures. (a) To... paragraph (a) of this Section, in cases involving incidents of terrorism preceding the establishment of this...

28 CFR 94.31 - Application procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Terrorism Victim Expense Reimbursement Program Program Administration § 94.31 Application procedures. (a) To... paragraph (a) of this Section, in cases involving incidents of terrorism preceding the establishment of this...

78 FR 79637 - Energy Conservation Program: Test Procedure for Set-Top Boxes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-31

... Energy Conservation Program: Test Procedure for Set-Top Boxes AGENCY: Office of Energy Efficiency and... Energy (DOE) withdraws a proposed rule published January 23, 2013 to establish a test procedure to... additional types of consumer products as covered products. (42 U.S.C. 6292(a)(20)) DOE may prescribe test...

76 FR 72332 - Energy Conservation Program: Test Procedure for Microwave Ovens

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-23

... Energy Conservation Program: Test Procedure for Microwave Ovens AGENCY: Office of Energy Efficiency and.... Department of Energy (DOE) published an interim final rule on March 9, 2011, amending its test procedures for... standby mode and off mode power use by microwave ovens. Those amendments incorporated into the DOE test...

78 FR 53625 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnaces and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-30

... Program for Consumer Products: Test Procedures for Residential Furnaces and Boilers; Correction AGENCY... Federal Register that amended the test procedure for residential furnaces and boilers (78 FR 41265). Due...., Washington, DC 20585-0121. Telephone: (202) 586-6590. Email: residential_furnaces_and_boilers@ee.doe.gov . Mr...

77 FR 4698 - Energy Conservation Program: Test Procedure and Energy Conservation Standard for Set-Top Boxes...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-31

... Conservation Program: Test Procedure and Energy Conservation Standard for Set-Top Boxes and Network Equipment... comments on the request for information pertaining to the development of test procedures and energy conservation standards for set-top boxes and network equipment. The comment period is extended to March 15...

76 FR 56126 - Energy Conservation Program: Treatment of “Smart” Appliances in Energy Conservation Standards and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-12

...'s energy conservation standards, as well as in test procedures used to demonstrate compliance with...'' appliances in the development of DOE's energy conservation standards, as well as in test procedures used to... Conservation Program: Treatment of ``Smart'' Appliances in Energy Conservation Standards and Test Procedures...

Program for User-Friendly Management of Input and Output Data Sets

NASA Technical Reports Server (NTRS)

Klimeck, Gerhard

2003-01-01

A computer program manages large, hierarchical sets of input and output (I/O) parameters (typically, sequences of alphanumeric data) involved in computational simulations in a variety of technological disciplines. This program represents sets of parameters as structures coded in object-oriented but otherwise standard American National Standards Institute C language. Each structure contains a group of I/O parameters that make sense as a unit in the simulation program with which this program is used. The addition of options and/or elements to sets of parameters amounts to the addition of new elements to data structures. By association of child data generated in response to a particular user input, a hierarchical ordering of input parameters can be achieved. Associated with child data structures are the creation and description mechanisms within the parent data structures. Child data structures can spawn further child data structures. In this program, the creation and representation of a sequence of data structures is effected by one line of code that looks for children of a sequence of structures until there are no more children to be found. A linked list of structures is created dynamically and is completely represented in the data structures themselves. Such hierarchical data presentation can guide users through otherwise complex setup procedures and it can be integrated within a variety of graphical representations.

Integral flange design program. [procedure for computing stresses

NASA Technical Reports Server (NTRS)

Wilson, J. F.

1974-01-01

An automated interactive flange design program utilizing an electronic desk top calculator is presented. The program calculates the operating and seating stresses for circular flanges of the integral or optional type subjected to internal pressure. The required input information is documented. The program provides an automated procedure for computing stresses in selected flange geometries for comparison to the allowable code values.

A STATE PLAN FOR COMMUNITY SERVICE AND CONTINUING EDUCATION PROGRAMS UNDER TITLE I OF THE HIGHER EDUCATION ACT OF 1965 SUBMITTED BY THE STATE OF LOUISIANA.

ERIC Educational Resources Information Center

DAVIDSON, JOHN W.; PELLEGRIN, LIONEL O.

THE LOUISIANA STATE PLAN INCLUDES ADMINISTRATIVE INFORMATION, PROCEDURES FOR SELECTING COMMUNITY PROBLEMS, INSTITUTIONS, AND REVIEWING APPLICATIONS, FISCAL AND INSTITUTIONAL ASSURANCES, ACCOUNTING PROCEDURES, REVIEW AND EVALUATION OF PROGRAMS, TRANSFER OF FUNDS, REPORTS, DETAILS OF THE ANNUAL PROGRAM, AND ELIGIBILITY OF PROGRAMS. GENERAL PROBLEM…

An Early-Warning System for Volcanic Ash Dispersal: The MAFALDA Procedure

NASA Astrophysics Data System (ADS)

Barsotti, S.; Nannipieri, L.; Neri, A.

2006-12-01

Forecasts of the dispersal of volcanic ash is a fundamental goal in order to mitigate its potential impact on urbanized areas and transport routes surrounding explosive volcanoes. To this aim we developed an early- warning procedure named MAFALDA (Modeling And Forecasting Ash Loading and Dispersal in the Atmosphere). Such tool is able to quantitatively forecast the atmospheric concentration of ash as well as the ground deposition as a function of time over a 3D spatial domain.\\The main features of MAFALDA are: (1) the use of the hybrid Lagrangian-Eulerian code VOL-CALPUFF able to describe both the rising column phase and the atmospheric dispersal as a function of weather conditions, (2) the use of high-resolution weather forecasting data, (3) the short execution time that allows to analyse a set of scenarios and (4) the web-based CGI software application (written in Perl programming language) that shows the results in a standard graphical web interface and makes it suitable as an early-warning system during volcanic crises.\\MAFALDA is composed by a computational part that simulates the ash cloud dynamics and a graphical interface for visualizing the modelling results. The computational part includes the codes for elaborating the meteorological data, the dispersal code and the post-processing programs. These produces hourly 2D maps of aerial ash concentration at several vertical levels, extension of "threat" area on air and 2D maps of ash deposit on the ground, in addition to graphs of hourly variations of column height.\\The processed results are available on the web by the graphical interface and the users can choose, by drop-down menu, which data to visualize. \\A first partial application of the procedure has been carried out for Mt. Etna (Italy). In this case, the procedure simulates four volcanological scenarios characterized by different plume intensities and uses 48-hrs weather forecasting data with a resolution of 7 km provided by the Italian Air Force.

77 FR 19408 - Dynamic Mobility Applications and Data Capture Management Programs; Notice of Public Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-30

... DEPARTMENT OF TRANSPORTATION Dynamic Mobility Applications and Data Capture Management Programs...) Intelligent Transportation System Joint Program Office (ITS JPO) will host a free public meeting to provide stakeholders an update on the Data Capture and Management (DCM) and Dynamic Mobility Applications (DMA...

Multibody dynamics model building using graphical interfaces

NASA Technical Reports Server (NTRS)

Macala, Glenn A.

1989-01-01

In recent years, the extremely laborious task of manually deriving equations of motion for the simulation of multibody spacecraft dynamics has largely been eliminated. Instead, the dynamicist now works with commonly available general purpose dynamics simulation programs which generate the equations of motion either explicitly or implicitly via computer codes. The user interface to these programs has predominantly been via input data files, each with its own required format and peculiarities, causing errors and frustrations during program setup. Recent progress in a more natural method of data input for dynamics programs: the graphical interface, is described.

42 CFR 460.54 - Termination procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (CONTINUED) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) Sanctions, Enforcement Actions, and Termination § 460.54 Termination procedures. (a) Except...

42 CFR 460.54 - Termination procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (CONTINUED) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) Sanctions, Enforcement Actions, and Termination § 460.54 Termination procedures. (a) Except...

Earth and ocean dynamics program

NASA Technical Reports Server (NTRS)

Vonbun, F. O.

1976-01-01

The objectives and requirements of the Earth and Ocean Dynamics Programs are outlined along with major goals and experiments. Spaceborne as well as ground systems needed to accomplish program goals are listed and discussed along with program accomplishments.

General approach and scope. [rotor blade design optimization

NASA Technical Reports Server (NTRS)

Adelman, Howard M.; Mantay, Wayne R.

1989-01-01

This paper describes a joint activity involving NASA and Army researchers at the NASA Langley Research Center to develop optimization procedures aimed at improving the rotor blade design process by integrating appropriate disciplines and accounting for all of the important interactions among the disciplines. The disciplines involved include rotor aerodynamics, rotor dynamics, rotor structures, airframe dynamics, and acoustics. The work is focused on combining these five key disciplines in an optimization procedure capable of designing a rotor system to satisfy multidisciplinary design requirements. Fundamental to the plan is a three-phased approach. In phase 1, the disciplines of blade dynamics, blade aerodynamics, and blade structure will be closely coupled, while acoustics and airframe dynamics will be decoupled and be accounted for as effective constraints on the design for the first three disciplines. In phase 2, acoustics is to be integrated with the first three disciplines. Finally, in phase 3, airframe dynamics will be fully integrated with the other four disciplines. This paper deals with details of the phase 1 approach and includes details of the optimization formulation, design variables, constraints, and objective function, as well as details of discipline interactions, analysis methods, and methods for validating the procedure.

Concept of Draft International Standard for a Unified Approach to Space Program Quality Assurance

NASA Astrophysics Data System (ADS)

Stryzhak, Y.; Vasilina, V.; Kurbatov, V.

2002-01-01

For want of the unified approach to guaranteed space project and product quality assurance, implementation of many international space programs has become a challenge. Globalization of aerospace industry and participation of various international ventures with diverse quality assurance requirements in big international space programs requires for urgent generation of unified international standards related to this field. To ensure successful fulfillment of space missions, aerospace companies should design and process reliable and safe products with properties complying or bettering User's (or Customer's) requirements. Quality of the products designed or processed by subcontractors (or other suppliers) should also be in compliance with the main user (customer)'s requirements. Implementation of this involved set of unified requirements will be made possible by creating and approving a system (series) of international standards under a generic title Space Product Quality Assurance based on a system consensus principle. Conceptual features of the baseline standard in this system (series) should comprise: - Procedures for ISO 9000, CEN and ECSS requirements adaptation and introduction into space product creation, design, manufacture, testing and operation; - Procedures for quality assurance at initial (design) phases of space programs, with a decision on the end product made based on the principle of independence; - Procedures to arrange incoming inspection of products delivered by subcontractors (including testing, audit of supplier's procedures, review of supplier's documentation), and space product certification; - Procedures to identify materials and primary products applied; - Procedures for quality system audit at the component part, primary product and materials supplier facilities; - Unified procedures to form a list of basic performances to be under configuration management; - Unified procedures to form a list of critical space product components, and unified procedures to define risks related to the specific component application and evaluate safety for the entire program implementation. In the eyes of the authors, those features together with a number of other conceptual proposals should constitute a unified standard-technical basis for implementing international space programs.

Administrative Plans. STIP II (Skill Training Improvement Programs Round II).

ERIC Educational Resources Information Center

Los Angeles Community Coll. District, CA.

Personnel policies, job responsibilities, and accounting procedures are summarized for the Los Angeles Community College District's Skill Training Improvement Programs (STIP II). This report first cites references to the established personnel and affirmative action procedures governing the program and then presents an organizational chart for the…

76 FR 34246 - Automated Commercial Environment (ACE); Announcement of National Customs Automation Program Test...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-13

... CBP with authority to conduct limited test programs or procedures designed to evaluate planned... aspects of this test, including the design, conduct and implementation of the test, in order to determine... Environment (ACE); Announcement of National Customs Automation Program Test of Automated Procedures for In...

23 CFR Appendix B to Part 1200 - HIGHWAY SAFETY PROGRAM COST SUMMARY (HS-217)

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false HIGHWAY SAFETY PROGRAM COST SUMMARY (HS-217) B APPENDIX B TO PART 1200 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION AND FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PROCEDURES FOR STATE HIGHWAY SAFETY PROGRAMS UNIFORM PROCEDURES FOR...

23 CFR Appendix B to Part 1200 - Highway Safety Program Cost Summary (HS-217)

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Highway Safety Program Cost Summary (HS-217) B Appendix B to Part 1200 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION AND FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PROCEDURES FOR STATE HIGHWAY SAFETY PROGRAMS UNIFORM PROCEDURES FOR...

Cost Analysis for Educational Program Evaluation.

ERIC Educational Resources Information Center

Haller, Emil J.

Concerned with the problem of determining program costs as part of the evaluation process, this article helps the practitioner arrive at useful conceptions of the term "cost" and procedures for assessing the costs of an educational program. Its purpose is to help design costing procedures for evaluation situations that are commonly encountered. An…

24 CFR 200.937 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... requirements under HUD building product standards and certification program for plastic bathtub units, plastic... procedural requirements under HUD building product standards and certification program for plastic bathtub... product certification program. In the case of plastic bathroom fixtures, testing and inspection shall be...

The Adam language: Ada extended with support for multiway activities

NASA Technical Reports Server (NTRS)

Charlesworth, Arthur

1993-01-01

The Adam language is an extension of Ada that supports multiway activities, which are cooperative activities involving two or more processes. This support is provided by three new constructs: diva procedures, meet statements, and multiway accept statements. Diva procedures are recursive generic procedures having a particular restrictive syntax that facilitates translation for parallel computers. Meet statements and multiway accept statements provide two ways to express a multiway rendezvous, which is an n-way rendezvous generalizing Ada's 2-way rendezvous. While meet statements tend to have simpler rules than multiway accept statements, the latter approach is a more straightforward extension of Ada. The only nonnull statements permitted within meet statements and multiway accept statements are calls on instantiated diva procedures. A call on an instantiated diva procedure is also permitted outside a multiway rendezvous; thus sequential Adam programs using diva procedures can be written. Adam programs are translated into Ada programs appropriate for use on parallel computers.

WIPP waste characterization program sampling and analysis guidance manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-01-01

The Waste Isolation Pilot Plant (WIPP) Waste Characterization Program Sampling and Analysis Guidance Manual (Guidance Manual) provides a unified source of information on the sampling and analytical techniques that enable Department of Energy (DOE) facilities to comply with the requirements established in the current revision of the Quality Assurance Program Plan (QAPP) for the WIPP Experimental-Waste Characterization Program (the Program). This Guidance Manual includes all of the sampling and testing methodologies accepted by the WIPP Project Office (DOE/WPO) for use in implementing the Program requirements specified in the QAPP. This includes methods for characterizing representative samples of transuranic (TRU) wastesmore » at DOE generator sites with respect to the gas generation controlling variables defined in the WIPP bin-scale and alcove test plans, as well as waste container headspace gas sampling and analytical procedures to support waste characterization requirements under the WIPP test program and the Resource Conservation and Recovery Act (RCRA). The procedures in this Guidance Manual are comprehensive and detailed and are designed to provide the necessary guidance for the preparation of site specific procedures. The use of these procedures is intended to provide the necessary sensitivity, specificity, precision, and comparability of analyses and test results. The solutions to achieving specific program objectives will depend upon facility constraints, compliance with DOE Orders and DOE facilities' operating contractor requirements, and the knowledge and experience of the TRU waste handlers and analysts. With some analytical methods, such as gas chromatography/mass spectrometry, the Guidance Manual procedures may be used directly. With other methods, such as nondestructive/destructive characterization, the Guidance Manual provides guidance rather than a step-by-step procedure.« less

Drivers of Environmental Institutional Dynamics in Decentralized African Countries.

PubMed

Hassenforder, Emeline; Barreteau, Olivier; Daniell, Katherine Anne; Pittock, Jamie; Ferrand, Nils

2015-12-01

This paper builds on the assumption that an effective approach to support the sustainability of natural resource management initiatives is institutional "bricolage." We argue that participatory planning processes can foster institutional bricolage by encouraging stakeholders to make their own arrangements based on the hybridization of old and new institutions. This papers aims at identifying how participatory process facilitators can encourage institutional bricolage. Specifically the paper investigates the specific contextual and procedural drivers of institutional dynamics in two case studies: the Rwenzori region in Uganda and the Fogera woreda in Ethiopia. In both cases, participatory planning processes were implemented. This research has three innovative aspects. First, it establishes a clear distinction between six terms which are useful for identifying, describing, and analyzing institutional dynamics: formal and informal; institutions and organizations; and emergence and change. Secondly, it compares the contrasting institutional dynamics in the two case studies. Thirdly, process-tracing is used to identify contextual and procedural drivers to institutional dynamics. We assume that procedural drivers can be used as "levers" by facilitators to trigger institutional bricolage. We found that facilitators need to pay particular attention to the institutional context in which the participatory planning process takes place, and especially at existing institutional gaps or failures. We identified three clusters of procedural levers: the selection and engagement of participants; the legitimacy, knowledge, and ideas of facilitators; and the design of the process, including the scale at which it is developed, the participatory tools used and the management of the diversity of frames.

Drivers of Environmental Institutional Dynamics in Decentralized African Countries

NASA Astrophysics Data System (ADS)

Hassenforder, Emeline; Barreteau, Olivier; Daniell, Katherine Anne; Pittock, Jamie; Ferrand, Nils

2015-12-01

This paper builds on the assumption that an effective approach to support the sustainability of natural resource management initiatives is institutional "bricolage." We argue that participatory planning processes can foster institutional bricolage by encouraging stakeholders to make their own arrangements based on the hybridization of old and new institutions. This papers aims at identifying how participatory process facilitators can encourage institutional bricolage. Specifically the paper investigates the specific contextual and procedural drivers of institutional dynamics in two case studies: the Rwenzori region in Uganda and the Fogera woreda in Ethiopia. In both cases, participatory planning processes were implemented. This research has three innovative aspects. First, it establishes a clear distinction between six terms which are useful for identifying, describing, and analyzing institutional dynamics: formal and informal; institutions and organizations; and emergence and change. Secondly, it compares the contrasting institutional dynamics in the two case studies. Thirdly, process-tracing is used to identify contextual and procedural drivers to institutional dynamics. We assume that procedural drivers can be used as "levers" by facilitators to trigger institutional bricolage. We found that facilitators need to pay particular attention to the institutional context in which the participatory planning process takes place, and especially at existing institutional gaps or failures. We identified three clusters of procedural levers: the selection and engagement of participants; the legitimacy, knowledge, and ideas of facilitators; and the design of the process, including the scale at which it is developed, the participatory tools used and the management of the diversity of frames.

Alternative Refractive Surgery Procedures

MedlinePlus

... alternative refractive surgery procedures to LASIK . Wavefront-Guided LASIK Before surgery, the excimer laser is programmed with ... precise "sculpting" of each unique cornea. In conventional LASIK , this programming is based on the patient's vision ...

Identifying areas of weakness in thoracic surgery residency training: a comparison of the perceptions of residents and program directors.

PubMed

Edwards, Janet P; Schofield, Adam; Paolucci, Elizabeth Oddone; Schieman, Colin; Kelly, Elizabeth; Servatyari, Ramin; Dixon, Elijah; Ball, Chad G; Grondin, Sean C

2014-01-01

To identify core thoracic surgery procedures that require increased emphasis during thoracic surgery residency for residents to achieve operative independence and to compare the perspectives of residents and program directors in this regard. A modified Delphi process was used to create a survey that was distributed electronically to all Canadian thoracic surgery residents (12) and program directors (8) addressing the residents' ability to perform 19 core thoracic surgery procedures independently after the completion of residency. Residents were also questioned about the adequacy of their operative exposure to these 19 procedures during their residency training. A descriptive summary including calculations of frequencies and proportions was conducted. The perceptions of the 2 groups were then compared using the Fisher exact test employing a Bonferroni correction. The relationship between residents' operative exposure and their perceived operative ability was explored in the same fashion. The response rate was 100% for residents and program directors. No statistical differences were found between residents' and program directors' perceptions of residents' ability to perform the 19 core procedures independently. Both groups identified lung transplantation, first rib resection, and extrapleural pneumonectomy as procedures for which residents were not adequately prepared to perform independently. Residents' subjective ratings of operative exposure were in good agreement with their reported operative ability for 13 of 19 procedures. This study provides new insight into the perceptions of thoracic surgery residents and their program directors regarding operative ability. This study points to good agreement between residents and program directors regarding residents' surgical capabilities. This study provides information regarding potential weaknesses in thoracic surgery training, which may warrant an examination of the curricula of existing programs as well as a reconsideration of what the scope of practice of a general thoracic surgeon should entail. © 2013 Published by Association of Program Directors in Surgery on behalf of Association of Program Directors in Surgery.

Fluid dynamics computer programs for NERVA turbopump

NASA Technical Reports Server (NTRS)

Brunner, J. J.

1972-01-01

During the design of the NERVA turbopump, numerous computer programs were developed for the analyses of fluid dynamic problems within the machine. Program descriptions, example cases, users instructions, and listings for the majority of these programs are presented.

Performance limitations of bilateral force reflection imposed by operator dynamic characteristics

NASA Technical Reports Server (NTRS)

Chapel, Jim D.

1989-01-01

A linearized, single-axis model is presented for bilateral force reflection which facilitates investigation into the effects of manipulator, operator, and task dynamics, as well as time delay and gain scaling. Structural similarities are noted between this model and impedance control. Stability results based upon this model impose requirements upon operator dynamic characteristics as functions of system time delay and environmental stiffness. An experimental characterization reveals the limited capabilities of the human operator to meet these requirements. A procedure is presented for determining the force reflection gain scaling required to provide stability and acceptable operator workload. This procedure is applied to a system with dynamics typical of a space manipulator, and the required gain scaling is presented as a function of environmental stiffness.

Acute Effect of Different Combined Stretching Methods on Acceleration and Speed in Soccer Players.

PubMed

Amiri-Khorasani, Mohammadtaghi; Calleja-Gonzalez, Julio; Mogharabi-Manzari, Mansooreh

2016-04-01

The purpose of this study was to investigate the acute effect of different stretching methods, during a warm-up, on the acceleration and speed of soccer players. The acceleration performance of 20 collegiate soccer players (body height: 177.25 ± 5.31 cm; body mass: 65.10 ± 5.62 kg; age: 16.85 ± 0.87 years; BMI: 20.70 ± 5.54; experience: 8.46 ± 1.49 years) was evaluated after different warm-up procedures, using 10 and 20 m tests. Subjects performed five types of a warm-up: static, dynamic, combined static + dynamic, combined dynamic + static, and no-stretching. Subjects were divided into five groups. Each group performed five different warm-up protocols in five non-consecutive days. The warm-up protocol used for each group was randomly assigned. The protocols consisted of 4 min jogging, a 1 min stretching program (except for the no-stretching protocol), and 2 min rest periods, followed by the 10 and 20 m sprint test, on the same day. The current findings showed significant differences in the 10 and 20 m tests after dynamic stretching compared with static, combined, and no-stretching protocols. There were also significant differences between the combined stretching compared with static and no-stretching protocols. We concluded that soccer players performed better with respect to acceleration and speed, after dynamic and combined stretching, as they were able to produce more force for a faster execution.

A digital computer program for the dynamic interaction simulation of controls and structure (DISCOS), volume 1

NASA Technical Reports Server (NTRS)

Bodley, C. S.; Devers, A. D.; Park, A. C.; Frisch, H. P.

1978-01-01

A theoretical development and associated digital computer program system for the dynamic simulation and stability analysis of passive and actively controlled spacecraft are presented. The dynamic system (spacecraft) is modeled as an assembly of rigid and/or flexible bodies not necessarily in a topological tree configuration. The computer program system is used to investigate total system dynamic characteristics, including interaction effects between rigid and/or flexible bodies, control systems, and a wide range of environmental loadings. In addition, the program system is used for designing attitude control systems and for evaluating total dynamic system performance, including time domain response and frequency domain stability analyses.

31 CFR 50.8 - Procedure for requesting determinations of controlling influence.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the Treasury TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.8 Procedure for requesting... controlling influence. Such submissions shall be made to the Terrorism Risk Insurance Program Office...

31 CFR 50.8 - Procedure for requesting determinations of controlling influence.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the Treasury TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.8 Procedure for requesting... controlling influence. Such submissions shall be made to the Terrorism Risk Insurance Program Office...

31 CFR 50.8 - Procedure for requesting determinations of controlling influence.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the Treasury TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.8 Procedure for requesting... controlling influence. Such submissions shall be made to the Terrorism Risk Insurance Program Office...

31 CFR 50.8 - Procedure for requesting determinations of controlling influence.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the Treasury TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.8 Procedure for requesting... controlling influence. Such submissions shall be made to the Terrorism Risk Insurance Program Office...

42 CFR 460.156 - Other enrollment procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (CONTINUED) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) Participant Enrollment and Disenrollment § 460.156 Other enrollment procedures. (a) Items a...

42 CFR 460.156 - Other enrollment procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (CONTINUED) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) Participant Enrollment and Disenrollment § 460.156 Other enrollment procedures. (a) Items a...

31 CFR 50.8 - Procedure for requesting determinations of controlling influence.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the Treasury TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.8 Procedure for requesting... controlling influence. Such submissions shall be made to the Terrorism Risk Insurance Program Office...

Program of Research in Structures and Dynamics

NASA Technical Reports Server (NTRS)

1988-01-01

The Structures and Dynamics Program was first initiated in 1972 with the following two major objectives: to provide a basic understanding and working knowledge of some key areas pertinent to structures, solid mechanics, and dynamics technology including computer aided design; and to provide a comprehensive educational and research program at the NASA Langley Research Center leading to advanced degrees in the structures and dynamics areas. During the operation of the program the research work was done in support of the activities of both the Structures and Dynamics Division and the Loads and Aeroelasticity Division. During the period of 1972 to 1986 the Program provided support for two full-time faculty members, one part-time faculty member, three postdoctoral fellows, one research engineer, eight programmers, and 28 graduate research assistants. The faculty and staff of the program have published 144 papers and reports, and made 70 presentations at national and international meetings, describing their research findings. In addition, they organized and helped in the organization of 10 workshops and national symposia in the structures and dynamics areas. The graduate research assistants and the students enrolled in the program have written 20 masters theses and 2 doctoral dissertations. The overall progress is summarized.

Bellman’s GAP—a language and compiler for dynamic programming in sequence analysis

PubMed Central

Sauthoff, Georg; Möhl, Mathias; Janssen, Stefan; Giegerich, Robert

2013-01-01

Motivation: Dynamic programming is ubiquitous in bioinformatics. Developing and implementing non-trivial dynamic programming algorithms is often error prone and tedious. Bellman’s GAP is a new programming system, designed to ease the development of bioinformatics tools based on the dynamic programming technique. Results: In Bellman’s GAP, dynamic programming algorithms are described in a declarative style by tree grammars, evaluation algebras and products formed thereof. This bypasses the design of explicit dynamic programming recurrences and yields programs that are free of subscript errors, modular and easy to modify. The declarative modules are compiled into C++ code that is competitive to carefully hand-crafted implementations. This article introduces the Bellman’s GAP system and its language, GAP-L. It then demonstrates the ease of development and the degree of re-use by creating variants of two common bioinformatics algorithms. Finally, it evaluates Bellman’s GAP as an implementation platform of ‘real-world’ bioinformatics tools. Availability: Bellman’s GAP is available under GPL license from http://bibiserv.cebitec.uni-bielefeld.de/bellmansgap. This Web site includes a repository of re-usable modules for RNA folding based on thermodynamics. Contact: robert@techfak.uni-bielefeld.de Supplementary information: Supplementary data are available at Bioinformatics online PMID:23355290

Computer program for calculating the flow field of supersonic ejector nozzles

NASA Technical Reports Server (NTRS)

Anderson, B. H.

1974-01-01

An analytical procedure for computing the performance of supersonic ejector nozzles is presented. This procedure includes real sonic line effects and an interaction analysis for the mixing process between the two streams. The procedure is programmed in FORTRAN 4 and has operated successfully on IBM 7094, IBM 360, CDC 6600, and Univac 1108.

Idaho Geothermal Commercialization Program. Idaho geothermal handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammer, G.D.; Esposito, L.; Montgomery, M.

The following topics are covered: geothermal resources in Idaho, market assessment, community needs assessment, geothermal leasing procedures for private lands, Idaho state geothermal leasing procedures - state lands, federal geothermal leasing procedures - federal lands, environmental and regulatory processes, local government regulations, geothermal exploration, geothermal drilling, government funding, private funding, state and federal government assistance programs, and geothermal legislation. (MHR)

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--STANDARD OPERATING PROCEDURE FOR TRANSFER AND RECEIPT OF DATA (UA-D-29.0)

EPA Science Inventory

The purpose of this SOP is to define the procedures involved in transferring and receiving data to and from other institutions. This procedure applies to the Arizona NHEXAS project and the Border study. Keywords: data; transfer.

The U.S.-Mexico Border Program is sponsored by ...

Use of a Computer Language in Teaching Dynamic Programming. Final Report.

ERIC Educational Resources Information Center

Trimble, C. J.; And Others

Most optimization problems of any degree of complexity must be solved using a computer. In the teaching of dynamic programing courses, it is often desirable to use a computer in problem solution. The solution process involves conceptual formulation and computational Solution. Generalized computer codes for dynamic programing problem solution…

The application of dynamic programming in production planning

NASA Astrophysics Data System (ADS)

Wu, Run

2017-05-01

Nowadays, with the popularity of the computers, various industries and fields are widely applying computer information technology, which brings about huge demand for a variety of application software. In order to develop software meeting various needs with most economical cost and best quality, programmers must design efficient algorithms. A superior algorithm can not only soul up one thing, but also maximize the benefits and generate the smallest overhead. As one of the common algorithms, dynamic programming algorithms are used to solving problems with some sort of optimal properties. When solving problems with a large amount of sub-problems that needs repetitive calculations, the ordinary sub-recursive method requires to consume exponential time, and dynamic programming algorithm can reduce the time complexity of the algorithm to the polynomial level, according to which we can conclude that dynamic programming algorithm is a very efficient compared to other algorithms reducing the computational complexity and enriching the computational results. In this paper, we expound the concept, basic elements, properties, core, solving steps and difficulties of the dynamic programming algorithm besides, establish the dynamic programming model of the production planning problem.

31 CFR 50.9 - Procedure for requesting general interpretations of statute.

Code of Federal Regulations, 2012 CFR

2012-07-01

... TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.9 Procedure for requesting general interpretations... request an interpretation of the Act or regulations by writing to the Terrorism Risk Insurance Program...

31 CFR 50.9 - Procedure for requesting general interpretations of statute.

Code of Federal Regulations, 2011 CFR

2011-07-01

... TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.9 Procedure for requesting general interpretations... request an interpretation of the Act or regulations by writing to the Terrorism Risk Insurance Program...

31 CFR 50.9 - Procedure for requesting general interpretations of statute.

Code of Federal Regulations, 2013 CFR

2013-07-01

... TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.9 Procedure for requesting general interpretations... request an interpretation of the Act or regulations by writing to the Terrorism Risk Insurance Program...

31 CFR 50.9 - Procedure for requesting general interpretations of statute.

Code of Federal Regulations, 2014 CFR

2014-07-01

... TERRORISM RISK INSURANCE PROGRAM General Provisions § 50.9 Procedure for requesting general interpretations... request an interpretation of the Act or regulations by writing to the Terrorism Risk Insurance Program...

77 FR 70105 - Energy Conservation Program: Test Procedures for Residential Dishwashers, Dehumidifiers, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-23

... Conservation Program: Test Procedures for Residential Dishwashers, Dehumidifiers, and Conventional Cooking... conventional cooking products under the Energy Policy and Conservation Act. DATES: The effective date of this...

Implementing Computer-Based Procedures: Thinking Outside the Paper Margins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxstrand, Johanna; Bly, Aaron

In the past year there has been increased interest from the nuclear industry in adopting the use of electronic work packages and computer-based procedures (CBPs) in the field. The goal is to incorporate the use of technology in order to meet the Nuclear Promise requirements of reducing costs and improve efficiency and decrease human error rates of plant operations. Researchers, together with the nuclear industry, have been investigating the benefits an electronic work package system and specifically CBPs would have over current paper-based procedure practices. There are several classifications of CBPs ranging from a straight copy of the paper-based proceduremore » in PDF format to a more intelligent dynamic CBP. A CBP system offers a vast variety of improvements, such as context driven job aids, integrated human performance tools (e.g., placekeeping and correct component verification), and dynamic step presentation. The latter means that the CBP system could only display relevant steps based on operating mode, plant status, and the task at hand. The improvements can lead to reduction of the worker’s workload and human error by allowing the work to focus on the task at hand more. A team of human factors researchers at the Idaho National Laboratory studied and developed design concepts for CBPs for field workers between 2012 and 2016. The focus of the research was to present information in a procedure in a manner that leveraged the dynamic and computational capabilities of a handheld device allowing the worker to focus more on the task at hand than on the administrative processes currently applied when conducting work in the plant. As a part of the research the team identified type of work, instructions, and scenarios where the transition to a dynamic CBP system might not be as beneficial as it would for other types of work in the plant. In most cases the decision to use a dynamic CBP system and utilize the dynamic capabilities gained will be beneficial to the worker. However, tasks that are reliant on the skill of the craft or have a short set of instructions may not provide a way or even need to utilize all the advanced capabilities in a dynamic CBP system. Therefore, a hybrid CBP system that could handle all the classifications of a CBP would be the best solution to take advantage of all that a CBP system offers. The implementation of a CBP system does not automatically improve the quality of procedures. Utilities should look into why each procedure is written the way it currently is on paper. Utilities should take the time before implementation to review, standardize format and update current procedures. Implementation of a CBP system can be a time to break out of traditional procedure writing processes and create new processes and procedures that take advantage of the capabilities a CBP system. This paper will summarize the research on CBPs and provide suggestions to take into consideration when implementing a CBP system.« less

Fracture of Structural Materials under Dynamic Loading

DTIC Science & Technology

1981-03-25

in character- izing the dynamic fracture resistance of materials, and in designing equipment and procedures for measuring dynamic fracture toughness...useful in assessing the safety of structures under dynamic loads, in characterizing the dyraamic fracture resistance of materials, and in designing ...I INTRODUCTION Structures used by the United States Air Force must be designed to resist catastrophic fracture when subjected ti dynamic loads. For

Confinement dynamics of a semiflexible chain inside nano-spheres

NASA Astrophysics Data System (ADS)

Fathizadeh, A.; Heidari, Maziar; Eslami-Mossallam, B.; Ejtehadi, M. R.

2013-07-01

We study the conformations of a semiflexible chain, confined in nano-scaled spherical cavities, under two distinct processes of confinement. Radial contraction and packaging are employed as two confining procedures. The former method is performed by gradually decreasing the diameter of a spherical shell which envelopes a confined chain. The latter procedure is carried out by injecting the chain inside a spherical shell through a hole on the shell surface. The chain is modeled with a rigid body molecular dynamics simulation and its parameters are adjusted to DNA base-pair elasticity. Directional order parameter is employed to analyze and compare the confined chain and the conformations of the chain for two different sizes of the spheres are studied in both procedures. It is shown that for the confined chains in the sphere sizes of our study, they appear in spiral or tennis-ball structures, and the tennis-ball structure is more likely to be observed in more compact confinements. Our results also show that the dynamical procedure of confinement and the rate of the confinement are influential parameters of the structure of the chain inside spherical cavities.

Dynamic Stiffness Transfer Function of an Electromechanical Actuator Using System Identification

NASA Astrophysics Data System (ADS)

Kim, Sang Hwa; Tahk, Min-Jea

2018-04-01

In the aeroelastic analysis of flight vehicles with electromechanical actuators (EMAs), an accurate prediction of flutter requires dynamic stiffness characteristics of the EMA. The dynamic stiffness transfer function of the EMA with brushless direct current (BLDC) motor can be obtained by conducting complicated mathematical calculations of control algorithms and mechanical/electrical nonlinearities using linearization techniques. Thus, system identification approaches using experimental data, as an alternative, have considerable advantages. However, the test setup for system identification is expensive and complex, and experimental procedures for data collection are time-consuming tasks. To obtain the dynamic stiffness transfer function, this paper proposes a linear system identification method that uses information obtained from a reliable dynamic stiffness model with a control algorithm and nonlinearities. The results of this study show that the system identification procedure is compact, and the transfer function is able to describe the dynamic stiffness characteristics of the EMA. In addition, to verify the validity of the system identification method, the simulation results of the dynamic stiffness transfer function and the dynamic stiffness model were compared with the experimental data for various external loads.

Automatic procedures generator for orbital rendezvous maneuver

NASA Technical Reports Server (NTRS)

Kohn, W.; Van Valkenburg, J. A.; Dunn, C. K.

1985-01-01

This paper describes the development of an expert system for defining and dynamically updating procedures for an orbital rendezvous maneuver. The product of the expert system is a procedure represented by a Moore automaton. The construction is recursive and driven by a simulation of the rendezvousing bodies.

78 FR 75961 - Energy Conservation Program: Test Procedures for Electric Motors

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-13

... Conservation Program: Test Procedures for Electric Motors; Final Rule #0;#0;Federal Register / Vol. 78 , No... CFR Part 431 [Docket No. EERE-2012-BT-TP-0043] RIN 1904-AC89 Energy Conservation Program: Test.... ACTION: Final rule. SUMMARY: The U.S. Department of Energy (DOE) is amending the energy efficiency test...

Evaluating Active Parental Consent Procedures for School Programming: Addressing the Sensitive Topic of Suicide Prevention

ERIC Educational Resources Information Center

Totura, Christine M. Wienke; Kutash, Krista; Labouliere, Christa D.; Karver, Marc S.

2017-01-01

Background: Suicide is the second leading cause of death for adolescents. Whereas school-based prevention programs are effective, obtaining active consent for youth participation in public health programming concerning sensitive topics is challenging. We explored several active consent procedures for improving participation rates. Methods: Five…

6 CFR 29.9 - Investigation and reporting of violation of PCII procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... inappropriate purpose, the PCII Program Manager may disqualify that entity or person from future receipt of any... procedures. 29.9 Section 29.9 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY... disclosure of PCII immediately to the PCII Program Manager or the PCII Program Manager's designees. Suspected...

6 CFR 29.9 - Investigation and reporting of violation of PCII procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... inappropriate purpose, the PCII Program Manager may disqualify that entity or person from future receipt of any... procedures. 29.9 Section 29.9 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY... disclosure of PCII immediately to the PCII Program Manager or the PCII Program Manager's designees. Suspected...

6 CFR 29.9 - Investigation and reporting of violation of PCII procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... inappropriate purpose, the PCII Program Manager may disqualify that entity or person from future receipt of any... procedures. 29.9 Section 29.9 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY... disclosure of PCII immediately to the PCII Program Manager or the PCII Program Manager's designees. Suspected...

6 CFR 29.9 - Investigation and reporting of violation of PCII procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... inappropriate purpose, the PCII Program Manager may disqualify that entity or person from future receipt of any... procedures. 29.9 Section 29.9 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY... disclosure of PCII immediately to the PCII Program Manager or the PCII Program Manager's designees. Suspected...

40 CFR 68.175 - Prevention program/Program 3.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operating procedures. (g) The date of the most recent review or revision of training programs; (1) The type of training provided—classroom, classroom plus on the job, on the job; and (2) The type of competency... review or revision of management of change procedures. (j) The date of the most recent pre-startup review...

40 CFR 68.175 - Prevention program/Program 3.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operating procedures. (g) The date of the most recent review or revision of training programs; (1) The type of training provided—classroom, classroom plus on the job, on the job; and (2) The type of competency... review or revision of management of change procedures. (j) The date of the most recent pre-startup review...

40 CFR 68.175 - Prevention program/Program 3.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operating procedures. (g) The date of the most recent review or revision of training programs; (1) The type of training provided—classroom, classroom plus on the job, on the job; and (2) The type of competency... review or revision of management of change procedures. (j) The date of the most recent pre-startup review...

40 CFR 68.175 - Prevention program/Program 3.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operating procedures. (g) The date of the most recent review or revision of training programs; (1) The type of training provided—classroom, classroom plus on the job, on the job; and (2) The type of competency... review or revision of management of change procedures. (j) The date of the most recent pre-startup review...

Teacher and Principal Survey Results in the National Preventive Dentistry Demonstration Program.

ERIC Educational Resources Information Center

Klein, Stephen P.; And Others

The National Preventive Dentistry Demonstration Program was conducted to assess the costs and benefits of combinations of school-based preventive dental care procedures. The program involved almost 30,000 elementary school children from 10 sites across the country. Classroom procedures, such as weekly fluoride mouthrinse, were administered or…

34 CFR 403.115 - What appeal procedures must be established under the Secondary School Vocational Education Program?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Secretary Assist Under the Basic Programs? Secondary, Postsecondary, and Adult Vocational Education Programs... of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF... 34 Education 3 2013-07-01 2013-07-01 false What appeal procedures must be established under the...

34 CFR 403.115 - What appeal procedures must be established under the Secondary School Vocational Education Program?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Secretary Assist Under the Basic Programs? Secondary, Postsecondary, and Adult Vocational Education Programs... of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF... 34 Education 3 2012-07-01 2012-07-01 false What appeal procedures must be established under the...

34 CFR 403.115 - What appeal procedures must be established under the Secondary School Vocational Education Program?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Secretary Assist Under the Basic Programs? Secondary, Postsecondary, and Adult Vocational Education Programs... of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF... 34 Education 3 2011-07-01 2011-07-01 false What appeal procedures must be established under the...

34 CFR 403.115 - What appeal procedures must be established under the Secondary School Vocational Education Program?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Secretary Assist Under the Basic Programs? Secondary, Postsecondary, and Adult Vocational Education Programs... of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF... 34 Education 3 2014-07-01 2014-07-01 false What appeal procedures must be established under the...

Degree of vertical integration between the undergraduate program and clinical internship with respect to cervical and cranial diagnostic and therapeutic procedures taught at the canadian memorial chiropractic college.

PubMed

Leppington, Charmody; Gleberzon, Brian; Fortunato, Lisa; Doucet, Nicolea; Vandervalk, Kyle

2012-01-01

The purpose of this study was to determine if diagnostic and therapeutic procedures for the cervical and cranial spine taught to students during the undergraduate program at Canadian Memorial Chiropractic College are required to be used during their internship by their supervising clinicians and, if so, to what extent these procedures are used. Course manuals and course syllabi from the Applied Chiropractic and Clinical Diagnosis faculty of the undergraduate chiropractic program for the academic year 2009-2010 were consulted and a list of all diagnostic and therapeutic procedures for the cranial and cervical spine was compiled. This survey asked clinicians to indicate if they themselves used or if they required the students they were supervising to use each procedure listed and, if so, to what extent each procedure was used. Demographic information of each clinician was also obtained. In general, most diagnostic procedures of the head and neck were seldom used, with the exception of postural observation and palpation. By contrast, most cervical orthopaedic tests were often used, with the exception of tests for vertigo. Most therapeutic procedures were used frequently with the exception of prone cervical and "muscle" adjustments. There was a low degree of vertical integration for cranial procedures as compared to a much higher degree of vertical integration for cervical procedures between the undergraduate and clinical internship programs taught. Vertical integration is an important element of curricular planning and these results may be helpful to aid educators to more appropriately allocate classroom instruction.

Mesh quality control for multiply-refined tetrahedral grids

NASA Technical Reports Server (NTRS)

Biswas, Rupak; Strawn, Roger

1994-01-01

A new algorithm for controlling the quality of multiply-refined tetrahedral meshes is presented in this paper. The basic dynamic mesh adaption procedure allows localized grid refinement and coarsening to efficiently capture aerodynamic flow features in computational fluid dynamics problems; however, repeated application of the procedure may significantly deteriorate the quality of the mesh. Results presented show the effectiveness of this mesh quality algorithm and its potential in the area of helicopter aerodynamics and acoustics.

North Korea after Kim Chong-il: Leadership Dynamics and Potential Crisis Scenarios

DTIC Science & Technology

2011-11-01

legal responsibility, and with specified procedures , the actual process is different.3 To date, regime dynamics in the Kim Chong-il era have been... procedures and regulations provide the outlines of formal rule, the 3 For a detailed examination of how...was also made an alternate member. It is also worth noting that 10 of the 12 members of the NDC were represented in the new Politburo lineup , thus

Optimization of reinforced concrete slabs

NASA Technical Reports Server (NTRS)

Ferritto, J. M.

1979-01-01

Reinforced concrete cells composed of concrete slabs and used to limit the effects of accidental explosions during hazardous explosives operations are analyzed. An automated design procedure which considers the dynamic nonlinear behavior of the reinforced concrete of arbitrary geometrical and structural configuration subjected to dynamic pressure loading is discussed. The optimum design of the slab is examined using an interior penalty function. The optimization procedure is presented and the results are discussed and compared with finite element analysis.

Assimilation of Biophysical Neuronal Dynamics in Neuromorphic VLSI.

PubMed

Wang, Jun; Breen, Daniel; Akinin, Abraham; Broccard, Frederic; Abarbanel, Henry D I; Cauwenberghs, Gert

2017-12-01

Representing the biophysics of neuronal dynamics and behavior offers a principled analysis-by-synthesis approach toward understanding mechanisms of nervous system functions. We report on a set of procedures assimilating and emulating neurobiological data on a neuromorphic very large scale integrated (VLSI) circuit. The analog VLSI chip, NeuroDyn, features 384 digitally programmable parameters specifying for 4 generalized Hodgkin-Huxley neurons coupled through 12 conductance-based chemical synapses. The parameters also describe reversal potentials, maximal conductances, and spline regressed kinetic functions for ion channel gating variables. In one set of experiments, we assimilated membrane potential recorded from one of the neurons on the chip to the model structure upon which NeuroDyn was designed using the known current input sequence. We arrived at the programmed parameters except for model errors due to analog imperfections in the chip fabrication. In a related set of experiments, we replicated songbird individual neuron dynamics on NeuroDyn by estimating and configuring parameters extracted using data assimilation from intracellular neural recordings. Faithful emulation of detailed biophysical neural dynamics will enable the use of NeuroDyn as a tool to probe electrical and molecular properties of functional neural circuits. Neuroscience applications include studying the relationship between molecular properties of neurons and the emergence of different spike patterns or different brain behaviors. Clinical applications include studying and predicting effects of neuromodulators or neurodegenerative diseases on ion channel kinetics.

Estimation of liquefaction-induced lateral spread from numerical modeling and its application

NASA Astrophysics Data System (ADS)

Meng, Xianhong

A noncoupled numerical procedure was developed using a scheme of pore water generation that causes shear modulus degradation and shear strength degradation resulting from earthquake cyclic motion. The designed Fast Lagrangian Analysis of Continua (FLAC) model procedure was tested using the liquefaction-induced lateral spread and ground response for Wildlife and Kobe sites. Sixteen well-documented case histories of lateral spread were reviewed and modeled using the modeling procedure. The dynamic residual strength ratios were back-calculated by matching the predicted displacement with the measured lateral spread, or with the displacement predicted by the Yound et al. model. Statistical analysis on the modeling results and soil properties show that most significant parameters governing the residual strength of the liquefied soil are the SPT blow count, fine content and soil particle size of the lateral spread layer. A regression equation was developed to express the residual strength values with these soil properties. Overall, this research demonstrated that a calibrated numerical model can predict the first order effectiveness of liquefaction-induced lateral spread using relatively simple parameters obtained from routine geotechnical investigation. In addition, the model can be used to plan a soil improvement program for cases where liquefaction remediation is needed. This allows the model to be used for design purposes at bridge approaches structured on liquefiable materials.

Using mixed methods effectively in prevention science: designs, procedures, and examples.

PubMed

Zhang, Wanqing; Watanabe-Galloway, Shinobu

2014-10-01

There is growing interest in using a combination of quantitative and qualitative methods to generate evidence about the effectiveness of health prevention, services, and intervention programs. With the emerging importance of mixed methods research across the social and health sciences, there has been an increased recognition of the value of using mixed methods for addressing research questions in different disciplines. We illustrate the mixed methods approach in prevention research, showing design procedures used in several published research articles. In this paper, we focused on two commonly used mixed methods designs: concurrent and sequential mixed methods designs. We discuss the types of mixed methods designs, the reasons for, and advantages of using a particular type of design, and the procedures of qualitative and quantitative data collection and integration. The studies reviewed in this paper show that the essence of qualitative research is to explore complex dynamic phenomena in prevention science, and the advantage of using mixed methods is that quantitative data can yield generalizable results and qualitative data can provide extensive insights. However, the emphasis of methodological rigor in a mixed methods application also requires considerable expertise in both qualitative and quantitative methods. Besides the necessary skills and effective interdisciplinary collaboration, this combined approach also requires an open-mindedness and reflection from the involved researchers.

Representing and reasoning about program in situation calculus

NASA Astrophysics Data System (ADS)

Yang, Bo; Zhang, Ming-yi; Wu, Mao-nian; Xie, Gang

2011-12-01

Situation calculus is an expressive tool for modeling dynamical system in artificial intelligence, changes in a dynamical world is represented naturally by the notions of action, situation and fluent in situation calculus. Program can be viewed as a discrete dynamical system, so it is possible to model program with situation calculus. To model program written in a smaller core programming language CL, notion of fluent is expanded for representing value of expression. Together with some functions returning concerned objects from expressions, a basic action theory of CL programming is constructed. Under such a theory, some properties of program, such as correctness and termination can be reasoned about.

A Categorization of Dynamic Analyzers

NASA Technical Reports Server (NTRS)

Lujan, Michelle R.

1997-01-01

Program analysis techniques and tools are essential to the development process because of the support they provide in detecting errors and deficiencies at different phases of development. The types of information rendered through analysis includes the following: statistical measurements of code, type checks, dataflow analysis, consistency checks, test data,verification of code, and debugging information. Analyzers can be broken into two major categories: dynamic and static. Static analyzers examine programs with respect to syntax errors and structural properties., This includes gathering statistical information on program content, such as the number of lines of executable code, source lines. and cyclomatic complexity. In addition, static analyzers provide the ability to check for the consistency of programs with respect to variables. Dynamic analyzers in contrast are dependent on input and the execution of a program providing the ability to find errors that cannot be detected through the use of static analysis alone. Dynamic analysis provides information on the behavior of a program rather than on the syntax. Both types of analysis detect errors in a program, but dynamic analyzers accomplish this through run-time behavior. This paper focuses on the following broad classification of dynamic analyzers: 1) Metrics; 2) Models; and 3) Monitors. Metrics are those analyzers that provide measurement. The next category, models, captures those analyzers that present the state of the program to the user at specified points in time. The last category, monitors, checks specified code based on some criteria. The paper discusses each classification and the techniques that are included under them. In addition, the role of each technique in the software life cycle is discussed. Familiarization with the tools that measure, model and monitor programs provides a framework for understanding the program's dynamic behavior from different, perspectives through analysis of the input/output data.

Regional variability in fecal microbiota transplantation practices: a survey of the Southern Ontario Fecal Microbiota Transplantation Movement.

PubMed

Hota, Susy S; Surangiwala, Salman; Paterson, Aimee S; Coburn, Bryan; Poutanen, Susan M

2018-04-18

There is growing evidence that fecal microbiota transplantation (FMT) is an effective treatment for recurrent Clostridium difficile infection, but little guidance exists for implementation of FMT programs. The objective of this study is to describe the program characteristics and protocols of 9 planned or operating FMT programs in the Southern Ontario Fecal Microbiota Transplantation (SOFT) Movement, to help guide future FMT program implementation. A 59-item survey was administered electronically to clinical leads of the SOFT Movement on June 2, 2016. The survey evaluated 7 domains: FMT program characteristics, FMT recipients, donor screening/selection, transplant manufacturing, FMT administration, good manufacturing procedures/biosafety procedures and infection-control procedures. We used descriptive statistics to analyze quantitative data. All 9 programs responded to the survey: 6 were active, 1 had FMT standard operating procedures developed but did not have clinical experience, and 2 were in the process of forming FMT programs. All 6 active programs performed FMT in adult patients with C. difficile infection. About 1300 FMT procedures were performed between 2003 and 2016. Five of the 6 operating programs administered the preparation via enema. Programs were driven primarily by physicians. All programs used universal FMT donors and followed Health Canada's screening guidelines, with considerable variability in screening frequency (every 3-6 mo) and modality. Locations for transplant preparation and manufacturing protocols varied across programs. Stool mass for FMT ranged from 20 g to 150 g, and transplant volume ranged from 25 mL to 300 mL. The experience of this high-volume regional FMT network highlights current challenges in FMT program development, including a high reliance on physicians and the costly nature of donor screening. Standardization and optimization through development of regional centres of excellence for FMT donor recruitment and administration should be explored. Copyright 2018, Joule Inc. or its licensors.

DIRAC: A new version of computer algebra tools for studying the properties and behavior of hydrogen-like ions

NASA Astrophysics Data System (ADS)

McConnell, Sean; Fritzsche, Stephan; Surzhykov, Andrey

2010-03-01

During recent years, the DIRAC package has proved to be an efficient tool for studying the structural properties and dynamic behavior of hydrogen-like ions. Originally designed as a set of MAPLE procedures, this package provides interactive access to the wave and Green's functions in the non-relativistic and relativistic frameworks and supports analytical evaluation of a large number of radial integrals that are required for the construction of transition amplitudes and interaction cross sections. We provide here a new version of the DIRAC program which is developed within the framework of MATHEMATICA (version 6.0). This new version aims to cater to a wider community of researchers that use the MATHEMATICA platform and to take advantage of the generally faster processing times therein. Moreover, the addition of new procedures, a more convenient and detailed help system, as well as source code revisions to overcome identified shortcomings should ensure expanded use of the new DIRAC program over its predecessor. New version program summaryProgram title: DIRAC Catalogue identifier: ADUQ_v2_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADUQ_v2_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC license, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 45 073 No. of bytes in distributed program, including test data, etc.: 285 828 Distribution format: tar.gz Programming language: Mathematica 6.0 or higher Computer: All computers with a license for the computer algebra package Mathematica (version 6.0 or higher) Operating system: Mathematica is O/S independent Classification: 2.1 Catalogue identifier of previous version: ADUQ_v1_0 Journal reference of previous version: Comput. Phys. Comm. 165 (2005) 139 Does the new version supersede the previous version?: Yes Nature of problem: Since the early days of quantum mechanics, the "hydrogen atom" has served as one of the key models for studying the structure and dynamics of various quantum systems. Its analytic solutions are frequently used in case studies in atomic and molecular physics, quantum optics, plasma physics, or even in the field of quantum information and computation. Fast and reliable access to functions and properties of the hydrogenic systems are frequently required, in both the non-relativistic and relativistic frameworks. Despite all the knowledge about one-electron ions, providing such an access is not a simple task, owing to the rather complicated mathematical structure of the Schrödinger and especially Dirac equations. Moreover, for analyzing experimental results as well as for performing advanced theoretical studies one often needs (apart from the detailed information on atomic wave- and Green's functions) to be able to calculate a number of integrals involving these functions. Although for many types of transition operators these integrals can be evaluated analytically in terms of special mathematical functions, such an evaluation is usually rather involved and prone to mistakes. Solution method: A set of Mathematica procedures is developed which provides both the non-relativistic and relativistic solutions of the "Hydrogen atom model". It facilitates, moreover, the symbolic evaluation of integrals involved in the calculations of cross sections and transition amplitudes. These procedures are based on a large number of relations among special mathematical functions, information about their integral representations, recurrence formulae and series expansions. Based on this knowledge, the DIRAC tools provide a fast and reliable algebraic (and if necessary, numeric) manipulation of functions and properties of one-electron systems, thus helping to obtain further insight into the behavior of quantum physical systems. Reasons for new version: The original version of the DIRAC program was developed as a toolbox of Maple procedures and was submitted to the CPC library in 2004 (cf. Ref. [1]). Since then DIRAC has found its niche in advanced theoretical studies carried out in realm of heavy ion physics. With the help of this program detailed analysis has been performed, in particular, for the various excitation and ionization processes occurring in relativistic ion-atom collisions [2], the polarization of the characteristic X-ray radiation following radiative electron capture [3], the correlation properties of the two-photon emission from few-electron heavy ions [4], the spin entanglement phenomena in atomic photoionization [5] and even for exploring the vibrational excitations of the heavy nuclei [6]. Although these studies have conclusively proven the potential of the program, they have also illuminated routes for its further enhancement. Apart from certain source code revisions, demand has grown for a new version of DIRAC compatible with the Mathematica platform. The version presented here includes a wider ranging and more user friendly interactive help system, a number of new procedures and reprogramming for greater computational efficiency. Summary of revisions: The most important new capabilities of the DIRAC program since the previous version are: The utilization of the Mathematica (version 6.0) platform. The addition of a number of new procedures. Since the complete list of the new (and updated) procedures can be found in the interactive help library of the program, we mention here only the most important ones: DiracGlobal[] - Displays a list of the current global settings which specify the framework, nuclear charge and the units which are to be used by the DIRAC program. DiracRadialOrbitalMomentum[] - Returns a non-relativistic radial orbital in momentum space for both, the bound and free electron states. DiracSlaterRadial[] - Evaluates the radial Slater integral both, with the non-relativistic and relativistic wavefunctions. In the previous version of the program this procedure was restricted to the non-relativistic framework only. DiracGreensIntegralRadial[] - Evaluates the two-dimensional radial integrals with the wave- and Green's functions both in non-relativistic and relativistic frameworks. DiracAngularMatrixElement[] - Calculates the angular matrix elements for various irreducible tensor operators. The elimination of some redundant procedures. In particular, the previous version supported evaluation of the spherical Bessel functions, Wigner 3j symbols, Clebsch-Gordan coefficients and spherical harmonics functions. These tools are now superseded by in-built procedures of Mathematica. The development of a full featured interactive help system which follows the style of the Mathematica Help Pages. Extensive revision of the source code in order to correct a number of bugs and inconsistencies that have been identified during use of the previous version of Dirac. The DIRAC package is distributed as a compressed tar file from which the DIRAC root directory can be (re-)generated. The root directory contains the source code and help libraries, a "Readme" file, Dirac_Installation_Instructions, as well as the notebook DemonstrationNotebook.nb that includes a number of test cases to illustrate the use of the program. These test cases, which concern the theoretical analysis of wavefunctions and the fine-structure of hydrogen-like ions, has already been discussed in detail in Ref. [1] and are provided here in order to underline the continuity between the previous (Maple) and new (Mathematica) versions of the DIRAC program. Unusual features: Even though all basic features of the previous Maple version have been retained in as close to the original form as possible, some small syntax changes became necessary in the new version of DIRAC in order to follow Mathematica standards. First of all, these changes concern naming conventions for DIRAC's procedures. As was discussed in Ref. [1], previously rather long names were employed in which each word was separated by an underscore. For example, when running the Maple version of the program one had to call the procedure Dirac_Slater_radial() in order to evaluate the Slater integral. Such a naming convention however, cannot be used in the Mathematica framework where the underscore character is reserved to represent Blank, a built-in symbol. In the new version of DIRAC we therefore follow the Mathematica convention of delimiting each word in a procedure's name by capitalization. Evaluation of the Slater determinant can be accomplished now simply by entering DiracSlaterRadial[]. Besides procedure names, a new convention is introduced to represent fundamental physical constants. In this version of DIRAC the group of (preset) global variables has changed to resemble their conventional symbols, specifically α, a, e, m, c and ℏ, being the fine structure constant, Bohr radius, electron charge, electron mass, speed of light and the Planck constant respectively. If the numerical evaluator N is wrapped around any of these constants, their numerical values are returned. Running time: Although the program replies promptly upon most requests, the running time also depends on the particular task. For example, computation of (radial) matrix elements involving components of relativistic wavefunctions might require a few seconds of a runtime. A number of test calculations performed regarding this and other tasks clearly indicate that the new version of Dirac requires up to 90% less evaluation time compared to its predecessor. References:A. Surzhykov, P. Koval, S. Fritzsche, Comput. Phys. Comm. 165 (2005) 139. H. Ogawa, et al., Phys. Rev. A 75 (2007) 1. A.V. Maiorova, et al., J. Phys. B: At. Mol. Opt. Phys. 42 (2009) 125003. L. Borowska, A. Surzhykov, Th. Stöhlker, S. Fritzsche, Phys. Rev. A 74 (2006) 062516. T. Radtke, S. Fritzsche, A. Surzhykov, Phys. Rev. A 74 (2006) 032709. A. Pálffy, Z. Harman, A. Surzhykov, U.D. Jentschura, Phys. Rev. A 75 (2007) 012712.

Configuring Airspace Sectors with Approximate Dynamic Programming

NASA Technical Reports Server (NTRS)

Bloem, Michael; Gupta, Pramod

2010-01-01

In response to changing traffic and staffing conditions, supervisors dynamically configure airspace sectors by assigning them to control positions. A finite horizon airspace sector configuration problem models this supervisor decision. The problem is to select an airspace configuration at each time step while considering a workload cost, a reconfiguration cost, and a constraint on the number of control positions at each time step. Three algorithms for this problem are proposed and evaluated: a myopic heuristic, an exact dynamic programming algorithm, and a rollouts approximate dynamic programming algorithm. On problem instances from current operations with only dozens of possible configurations, an exact dynamic programming solution gives the optimal cost value. The rollouts algorithm achieves costs within 2% of optimal for these instances, on average. For larger problem instances that are representative of future operations and have thousands of possible configurations, excessive computation time prohibits the use of exact dynamic programming. On such problem instances, the rollouts algorithm reduces the cost achieved by the heuristic by more than 15% on average with an acceptable computation time.

POLYMAT-C: a comprehensive SPSS program for computing the polychoric correlation matrix.

PubMed

Lorenzo-Seva, Urbano; Ferrando, Pere J

2015-09-01

We provide a free noncommercial SPSS program that implements procedures for (a) obtaining the polychoric correlation matrix between a set of ordered categorical measures, so that it can be used as input for the SPSS factor analysis (FA) program; (b) testing the null hypothesis of zero population correlation for each element of the matrix by using appropriate simulation procedures; (c) obtaining valid and accurate confidence intervals via bootstrap resampling for those correlations found to be significant; and (d) performing, if necessary, a smoothing procedure that makes the matrix amenable to any FA estimation procedure. For the main purpose (a), the program uses a robust unified procedure that allows four different types of estimates to be obtained at the user's choice. Overall, we hope the program will be a very useful tool for the applied researcher, not only because it provides an appropriate input matrix for FA, but also because it allows the researcher to carefully check the appropriateness of the matrix for this purpose. The SPSS syntax, a short manual, and data files related to this article are available as Supplemental materials that are available for download with this article.

Hydraulic dynamic analysis

NASA Technical Reports Server (NTRS)

Gale, R. L.; Nease, A. W.; Nelson, D. J.

1978-01-01

Computer program mathematically describes complete hydraulic systems to study their dynamic performance. Program employs subroutines that simulate components of hydraulic system, which are then controlled by main program. Program is useful to engineers working with detailed performance results of aircraft, spacecraft, or similar hydraulic systems.

Engaging men as promotores de salud: perceptions of community health workers among Latino men in North Carolina.

PubMed

Villa-Torres, Laura; Fleming, Paul J; Barrington, Clare

2015-02-01

The promotor de salud, or community health worker (CHW) role, is highly feminized and little is known about how men view their participation in CHW programs. We conducted in-depth interviews with Latino men in North Carolina to explore this gap. We used systematic coding and display procedures informed by Grounded Theory to analyze the data. Men described their communities as lacking cohesion, making integration of Latino immigrants difficult. Most did not consider themselves leaders or feel they had leaders in their communities. Their perceptions of the feminized CHW role as well as the volunteer or low-paid nature of CHW work conflicted with men's provider role. They also did not think they could perform the CHW role because they lacked education, skills, and broad networks. Efforts to increase male participation in CHW programs in new Latino immigrant destinations will need to understand and address these gender and migration-related dynamics in order to engage both women and men in improving the health of their communities.

Computational strategies for three-dimensional flow simulations on distributed computer systems. Ph.D. Thesis Semiannual Status Report, 15 Aug. 1993 - 15 Feb. 1994

NASA Technical Reports Server (NTRS)

Weed, Richard Allen; Sankar, L. N.

1994-01-01

An increasing amount of research activity in computational fluid dynamics has been devoted to the development of efficient algorithms for parallel computing systems. The increasing performance to price ratio of engineering workstations has led to research to development procedures for implementing a parallel computing system composed of distributed workstations. This thesis proposal outlines an ongoing research program to develop efficient strategies for performing three-dimensional flow analysis on distributed computing systems. The PVM parallel programming interface was used to modify an existing three-dimensional flow solver, the TEAM code developed by Lockheed for the Air Force, to function as a parallel flow solver on clusters of workstations. Steady flow solutions were generated for three different wing and body geometries to validate the code and evaluate code performance. The proposed research will extend the parallel code development to determine the most efficient strategies for unsteady flow simulations.

The promise and problems of non-physician practitioners in general surgery education: Results of a multi-center, mixed-methods study of faculty.

PubMed

Coverdill, James E; Shelton, Jeff Scott; Alseidi, Adnan; Borgstrom, David C; Dent, Daniel L; Dumire, Russell; Fryer, Jonathan; Hartranft, Thomas H; Holsten, Steven B; Nelson, M Timothy; Shabahang, Mohsen M; Sherman, Stanley R; Termuhlen, Paula M; Woods, Randy J; Mellinger, John D

2018-02-01

Nurse Practitioners and Physician Assistants - called non-physician practitioners or NPPs - are common, but little is known about their educational promise and problems. General surgery faculty in 13 residency programs were surveyed (N = 279 with a 71% response rate) and interviewed (N = 43) about experiences with NPPs. The survey documents overall patterns and differences by program type and primary service; interviews point to deeper rationales and concerns. NPPs reduce faculty and resident workloads and teach residents. NPPs also reduce resident exposure to educationally valuable activities, and faculty sometimes round, make decisions, and operate with NPPs instead of residents. Interviews indicate that NPPs can overly reduce resident involvement in patient care, diminish resident responsibility and decision making, disrupt team dynamics, and compete for procedures. NPPs both enhance and hinder surgical education and highlight the need to more clearly articulate learning outcomes for residents and activities necessary to achieve those outcomes. Copyright © 2017 Elsevier Inc. All rights reserved.

40 CFR 403.11 - Approval procedures for POTW pretreatment programs and POTW granting of removal credits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GENERAL PRETREATMENT REGULATIONS FOR EXISTING AND NEW SOURCES OF POLLUTION § 403.11 Approval procedures for POTW pretreatment programs...

User's guide to the western spruce budworm modeling system

Treesearch

Nicholas L. Crookston; J. J. Colbert; Paul W. Thomas; Katharine A. Sheehan; William P. Kemp

1990-01-01

The Budworm Modeling System is a set of four computer programs: The Budworm Dynamics Model, the Prognosis-Budworm Dynamics Model, the Prognosis-Budworm Damage Model, and the Parallel Processing-Budworm Dynamics Model. Input to the first three programs and the output produced are described in this guide. A guide to the fourth program will be published separately....

Procedures for Hearings Conducted Pursuant to 40 CFR Part 7--Nondiscrimination in Programs and Activities Receiving Federal Assistance from the U.S. Environmental Protection Agency

EPA Pesticide Factsheets

The document clarifies the U.S. Environmental Protection Agency’s procedures for hearings in administrative complaints of discrimination in programs and activities receiving EPA assistance, as those procedures are set forth in 40 C.F.R. §§ 7.130 and 7.13

Controlled Confrontation: The Ward Grievance Procedure of the California Youth Authority. An Exemplary Project.

ERIC Educational Resources Information Center

National Inst. of Law Enforcement and Criminal Justice (Dept. of Justice/LEAA), Washington, DC.

The Ward Grievance Procedure of the California Youth Authority is one of 17 programs that earned the National Institute's "Exemplary" label. This brochure provides the requisite practical information for those who wish to test or consider testing the ward grievance procedure. The program was developed as a way of dealing with the questions raised…

Programmable display of DNA-protein chimeras for controlling cell-hydrogel interactions via reversible intermolecular hybridization.

PubMed

Zhang, Zhaoyang; Li, Shihui; Chen, Niancao; Yang, Cheng; Wang, Yong

2013-04-08

Extensive studies have been recently carried out to achieve dynamic control of cell-material interactions primarily through physicochemical stimulation. The purpose of this study was to apply reversible intermolecular hybridization to program cell-hydrogel interactions in physiological conditions based on DNA-antibody chimeras and complementary oligonucleotides. The results showed that DNA oligonucleotides could be captured to and released from the immobilizing DNA-functionalized hydrogels with high specificity via DNA hybridization. Accordingly, DNA-antibody chimeras were captured to the hydrogels, successfully inducing specific cell attachment. The cell attachment to the hydrogels reached the plateau at approximately half an hour after the functionalized hydrogels and the cells were incubated together. The attached cells were rapidly released from the bound hydrogels when triggering complementary oligonucleotides were introduced to the system. However, the capability of the triggering complementary oligonucleotides in releasing cells was affected by the length of intermolecular hybridization. The length needed to be at least more than 20 base pairs in the current experimental setting. Notably, because the procedure of intermolecular hybridization did not involve any harsh condition, the released cells maintained the same viability as that of the cultured cells. The functionalized hydrogels also exhibited the potential to catch and release cells repeatedly. Therefore, this study demonstrates that it is promising to regulate cell-material interactions dynamically through the DNA-programmed display of DNA-protein chimeras.

Image 100 procedures manual development: Applications system library definition and Image 100 software definition

NASA Technical Reports Server (NTRS)

Guseman, L. F., Jr.; Decell, H. P., Jr.

1975-01-01

An outline for an Image 100 procedures manual for Earth Resources Program image analysis was developed which sets forth guidelines that provide a basis for the preparation and updating of an Image 100 Procedures Manual. The scope of the outline was limited to definition of general features of a procedures manual together with special features of an interactive system. Computer programs were identified which should be implemented as part of an applications oriented library for the system.

Space station structures and dynamics test program

NASA Technical Reports Server (NTRS)

Moore, Carleton J.; Townsend, John S.; Ivey, Edward W.

1987-01-01

The design, construction, and operation of a low-Earth orbit space station poses unique challenges for development and implementation of new technology. The technology arises from the special requirement that the station be built and constructed to function in a weightless environment, where static loads are minimal and secondary to system dynamics and control problems. One specific challenge confronting NASA is the development of a dynamics test program for: (1) defining space station design requirements, and (2) identifying the characterizing phenomena affecting the station's design and development. A general definition of the space station dynamic test program, as proposed by MSFC, forms the subject of this report. The test proposal is a comprehensive structural dynamics program to be launched in support of the space station. The test program will help to define the key issues and/or problems inherent to large space structure analysis, design, and testing. Development of a parametric data base and verification of the math models and analytical analysis tools necessary for engineering support of the station's design, construction, and operation provide the impetus for the dynamics test program. The philosophy is to integrate dynamics into the design phase through extensive ground testing and analytical ground simulations of generic systems, prototype elements, and subassemblies. On-orbit testing of the station will also be used to define its capability.

Dynamic tests of composite panels of an aircraft wing

NASA Astrophysics Data System (ADS)

Splichal, Jan; Pistek, Antonin; Hlinka, Jiri

2015-10-01

The paper describes the analysis of aerospace composite structures under dynamic loading. Today, it is common to use design procedures based on assumption of static loading only, and dynamic loading is rarely assumed and applied in design and certification of aerospace structures. The paper describes the application of dynamic loading for the design of aircraft structures, and the validation of the procedure on a selected structure. The goal is to verify the possibility of reducing the weight through improved design/modelling processes using dynamic loading instead of static loading. The research activity focuses on the modelling and testing of a composite panel representing a local segment of an aircraft wing section, investigating in particular the buckling behavior under dynamic loading. Finite Elements simulation tools are discussed, as well as the advantages of using a digital optical measurement system for the evaluation of the tests. The comparison of the finite element simulations with the results of the tests is presented.

Enhancements of Bayesian Blocks; Application to Large Light Curve Databases

NASA Technical Reports Server (NTRS)

Scargle, Jeff

2015-01-01

Bayesian Blocks are optimal piecewise linear representations (step function fits) of light-curves. The simple algorithm implementing this idea, using dynamic programming, has been extended to include more data modes and fitness metrics, multivariate analysis, and data on the circle (Studies in Astronomical Time Series Analysis. VI. Bayesian Block Representations, Scargle, Norris, Jackson and Chiang 2013, ApJ, 764, 167), as well as new results on background subtraction and refinement of the procedure for precise timing of transient events in sparse data. Example demonstrations will include exploratory analysis of the Kepler light curve archive in a search for "star-tickling" signals from extraterrestrial civilizations. (The Cepheid Galactic Internet, Learned, Kudritzki, Pakvasa1, and Zee, 2008, arXiv: 0809.0339; Walkowicz et al., in progress).

Epinephrine Policies and Protocols Guidance for Schools: Equipping School Nurses to Save Lives.

PubMed

Tanner, Andrea; Clarke, Carrie

2016-01-01

In response to limited direction given by legislative bodies to school nurses about how to implement state-mandated or recommended stock epinephrine programs in their schools, NASN convened a workgroup of invested stakeholders. This workgroup was challenged to equip school nurses with the necessary tools to develop policies and protocols regarding stock epinephrine in their school districts. The dynamic workgroup subcommittees focused on policies, procedures, and reporting tools. This article reviews the results of the subcommittees' work and the overall collaboration within the workgroup. This article provides clear, nationally recognized guidance on the best practice for establishing stock epinephrine policies and protocols with reporting tools at the local school district level. © 2015 The Author(s).

Development and evaluation of the impulse transfer function technique

NASA Technical Reports Server (NTRS)

Mantus, M.

1972-01-01

The development of the test/analysis technique known as the impulse transfer function (ITF) method is discussed. This technique, when implemented with proper data processing systems, should become a valuable supplement to conventional dynamic testing and analysis procedures that will be used in the space shuttle development program. The method can relieve many of the problems associated with extensive and costly testing of the shuttle for transient loading conditions. In addition, the time history information derived from impulse testing has the potential for being used to determine modal data for the structure under investigation. The technique could be very useful in determining the time-varying modal characteristics of structures subjected to thermal transients, where conventional mode surveys are difficult to perform.