Properties of concrete containing scrap-tire rubber--an overview.

PubMed

Siddique, Rafat; Naik, Tarun R

2004-01-01

Solid waste management is one of the major environmental concerns in the United States. Over 5 billion tons of non-hazardous solid waste materials are generated in USA each year. Of these, more than 270 million scrap-tires (approximately 3.6 million tons) are generated each year. In addition to this, about 300 million scrap-tires have been stockpiled. Several studies have been carried out to reuse scrap-tires in a variety of rubber and plastic products, incineration for production of electricity, or as fuel for cement kilns, as well as in asphalt concrete. Studies show that workable rubberized concrete mixtures can be made with scrap-tire rubber. This paper presents an overview of some of the research published regarding the use of scrap-tires in portland cement concrete. The benefits of using magnesium oxychloride cement as a binder for rubberized concrete mixtures are also presented. The paper details the likely uses of rubberized concrete.

Installation for burning-out scrap metal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gutschmidt, P.

1982-08-24

Disclosed is an installation for burning-out scrap metal goods for the purpose of reclaiming scrap metal, comprising at least one furnace wagon, which is capable of being loaded with the scrap metal goods to be burned out; at least one burning-out chamber into which the furnace wagon is movable for burning-out the scrap metal goods to produce scrap steel; means for heating the burning-out chamber to a temperature of at least about 600* C.; at least one afterburning chamber communicating with the burning-out chamber for afterburning flue gases produced in the burning-out chamber at a temperature from about 1100* tomore » 1200* C.; a waste gas purifying plant communicating with the afterburning chamber for eliminating the flue gas impurities and for the scrubbing of the flue-gases originating from the afterburning chamber; and at least one cooling chamber arranged adjacent to and in selective communication with the burning-out chamber for cooling the burned-out material.« less

Productivity and cost estimators for conventional ground-based skidding on steep terrain using preplanned skid roads

Treesearch

Michael D. Erickson; Curt C. Hassler; Chris B. LeDoux

1991-01-01

Continuous time and motion study techniques were used to develop productivity and cost estimators for the skidding component of ground-based logging systems, operating on steep terrain using preplanned skid roads. Comparisons of productivity and costs were analyzed for an overland random access skidding method, verses a skidding method utilizing a network of preplanned...

Collection and recycling of electronic scrap: A worldwide overview and comparison with the Brazilian situation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reis de Oliveira, Camila, E-mail: Camilareis.oliveira@hotmail.com; Moura Bernardes, Andrea, E-mail: amb@ufrgs.br; Gerbase, Annelise Engel, E-mail: agerbase@ufrgs.br

Highlights: Black-Right-Pointing-Pointer Review of the different e-waste collection systems and recycling processes. Black-Right-Pointing-Pointer We present the e-waste collection systems used in Europe and in the US. Black-Right-Pointing-Pointer We present e-waste collection systems used in Asia and Latin America. Black-Right-Pointing-Pointer E-waste management between developed and developing countries is very different. Black-Right-Pointing-Pointer We made a comparison of the world situation to the current Brazilian reality. - Abstract: Recycling and the related issue of sustainable development are increasing in importance around the world. In Brazil, the new National Policy on Solid Wastes has prompted discussion on the future of electronic waste (e-waste). Overmore » the last 10 years, different e-waste collection systems and recycling processes have been applied globally. This paper presents the systems used in different countries and compares the world situation to the current Brazilian reality. To establish a recycling process, it is necessary to organize efficient collection management. The main difficulty associated with the implementation of e-waste recycling processes in Brazil is the collection system, as its efficiency depends not only on the education and cooperation of the people but also on cooperation among industrial waste generators, distributors and the government. Over half a million waste pickers have been reported in Brazil and they are responsible for the success of metal scrap collection in the country. The country also has close to 2400 companies and cooperatives involved in recycling and scrap trading. On the other hand, the collection and recycling of e-waste is still incipient because e-wastes are not seen as valuable in the informal sector. The Brazilian challenge is therefore to organize a system of e-waste management including the informal sector without neglecting environmentally sound management principles.« less

90. VIEW OF OXIDIZER APRON AND SOUTH SIDE OF SKID ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

90. VIEW OF OXIDIZER APRON AND SOUTH SIDE OF SKID 9, SKID 7, AND SKID 9A. COOLING TOWER ON NORTH SIDE OF OXIDIZER APRON. LEFT TO RIGHT IN BACKGROUND: METEOROLOGICAL TOWER, SLC-3W MST, SURPLUS ATLAS E/F LAUNCHER, PYROTECHNIC SHED (BLDG. 757), STORAGE SHED (BLDG. 776), CABLE TRAYS, AND TOP OF LAUNCH OPERATIONS BUILDING (BLDG. 763). - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

Electronic waste (e-waste): material flows and management practices in Nigeria.

PubMed

Nnorom, Innocent Chidi; Osibanjo, Oladele

2008-01-01

The growth in electrical and electronic equipment (EEE) production and consumption has been exponential in the last two decades. This has been as a result of the rapid changes in equipment features and capabilities, decrease in prices, and the growth in internet use. This creates a large volume of waste stream of obsolete electrical and electronic devices (e-waste) in developed countries. There is high level of trans-boundary movement of these devices as secondhand electronic equipment into developing countries in an attempt to bridge the 'digital divide'. The past decade has witnessed a phenomenal advancement in information and communication technology (ICT) in Nigeria, most of which rely on imported secondhand devices. This paper attempts to review the material flow of secondhand/scrap electronic devices into Nigeria, the current management practices for e-waste and the environmental and health implications of such low-end management practices. Establishment of formal recycling facilities, introduction of legislation dealing specifically with e-waste and the confirmation of the functionality of secondhand EEE prior to importation are some of the options available to the government in dealing with this difficult issue.

Electronic waste (e-waste): Material flows and management practices in Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nnorom, Innocent Chidi; Osibanjo, Oladele

The growth in electrical and electronic equipment (EEE) production and consumption has been exponential in the last two decades. This has been as a result of the rapid changes in equipment features and capabilities, decrease in prices, and the growth in internet use. This creates a large volume of waste stream of obsolete electrical and electronic devices (e-waste) in developed countries. There is high level of trans-boundary movement of these devices as secondhand electronic equipment into developing countries in an attempt to bridge the 'digital divide'. The past decade has witnessed a phenomenal advancement in information and communication technology (ICT)more » in Nigeria, most of which rely on imported secondhand devices. This paper attempts to review the material flow of secondhand/scrap electronic devices into Nigeria, the current management practices for e-waste and the environmental and health implications of such low-end management practices. Establishment of formal recycling facilities, introduction of legislation dealing specifically with e-waste and the confirmation of the functionality of secondhand EEE prior to importation are some of the options available to the government in dealing with this difficult issue.« less

Method for forming consumable electrodes from metallic chip scraps

DOEpatents

Girshov, Vladimir Leonidovich; Podpalkin, Arcady Munjyvich; Treschevskiy, Arnold Nikolayevich; Abramov, Alexey Alexandrovich

2005-10-11

The method relates to metallurgical recycling of waste products, preferably titanium alloys chips scrap. Accordingly after crushing and cleaning, the chip scrap is subjected to vacuum-thermal degassing (VTD); the chip scrap is pressed into briquettes; the briquettes are placed into a mould allowing sufficient remaining space for the addition of molten metal alloy; the mould is pre-heated before filling with the molten metal alloy; the mould remaining space is filled with molten metal alloy. After cooling, the electrode is removed from the mould. The method provides a means for 100% use of chip scrap in producing consumable electrodes having increased mechanical strength and reduced interstitial impurities content leading to improved secondary cast alloys.

40 CFR 761.72 - Scrap metal recovery ovens and smelters.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Scrap metal recovery ovens and..., AND USE PROHIBITIONS Storage and Disposal § 761.72 Scrap metal recovery ovens and smelters. Any person... § 761.60(b), metal surfaces in PCB remediation waste regulated under § 761.61, or metal surfaces in PCB...

Tests of highly loaded skids on a concrete runway

NASA Technical Reports Server (NTRS)

Stubbs, Sandy M.; Daugherty, Robert H.

1994-01-01

Skids have been used at various times for aircraft landing gear ever since the Wright Flyer appeared in the early 1900's. Typically, skids have been employed as aircraft landing gear either at low speeds or at low bearing pressures. Tests were conducted to examine the friction and wear characteristics of various metals sliding on a rough, grooved concrete runway. The metals represented potential materials for an overload protection skid for the Space Shuttle orbiter. Data from tests of six skid specimens conducted at higher speeds and bearing pressures than those of previous tests in the open literature are presented. Skids constructed of tungsten with embedded carbide chips exhibited the lowest wear, whereas a skid constructed of Inconel 718 exhibited high wear rates. Friction coefficients for all the skid specimens were moderate and would provide adequate stopping performance on a long runway. Because of its low wear rate, a skid constructed of tungsten with embedded carbide chips is considered to be a likely candidate for an aircraft skid or overload protection skid.

X-38 Landing Gear Skid Test Report

NASA Technical Reports Server (NTRS)

Gafka, George K.; Daugherty, Robert H.

2000-01-01

NASA incorporates skid-equipped landing gear on its series of X-38 flight test vehicles. The X-38 test program is the proving ground for the Crew Return Vehicle (CRV) a gliding parafoil-equipped vehicle designed to land at relatively low speeds. The skid-equipped landing gear is designed to attenuate the vertical landing energy of the vehicle at touchdown using crushable materials within the struts themselves. The vehicle then slides out as the vehicle horizontal energy is dissipated through the skids. A series of tests was conducted at Edwards Airforce Base (EAFB) in an attempt to quantify the drag force produced while "dragging" various X-38 landing gear skids across lakebed regions of varying surface properties. These data were then used to calculate coefficients of friction for each condition. Coefficient of friction information is critical for landing analyses as well as for landing gear load and interface load analysis. The skid specimens included full- and sub-scale V201 (space test vehicle) nose and main gear designs, a V131/V 132 (atmospheric flight test vehicles) main gear skid (actual flight hardware), and a newly modified, full-scale V201 nose -ear skid with substantially increased edge curvature as compared to its original design. Results of the testing are discussed along with comments on the relative importance of various parameters that influence skid stability and other dynamic behavior.

The Demise of Skid Row.

ERIC Educational Resources Information Center

Siegal, Harvey A.; Inciardi, James A.

1982-01-01

Describes the history and evolution of the American skid row; analyzes the changes it has undergone, particularly in the face of urban renewal; and speculates on its future. Includes opinions of the inhabitants of skid row which were obtained from interviews. (MJL)

Upgrade Recycling of Cast Iron Scrap Chips towards β-FeSi₂ Thermoelectric Materials.

PubMed

Laila, Assayidatul; Nanko, Makoto; Takeda, Masatoshi

2014-09-04

The upgrade recycling of cast-iron scrap chips towards β-FeSi₂ thermoelectric materials is proposed as an eco-friendly and cost-effective production process. By using scrap waste from the machining process of cast-iron components, the material cost to fabricate β-FeSi₂ is reduced and the industrial waste is recycled. In this study, β-FeSi₂ specimens obtained from cast iron scrap chips were prepared both in the undoped form and doped with Al and Co elements. The maximum figure of merit ( ZT ) indicated a thermoelectric performance of approximately 70% in p-type samples and nearly 90% in n-type samples compared to β-FeSi₂ prepared from pure Fe and other published studies. The use of cast iron scrap chips to produce β-FeSi₂ shows promise as an eco-friendly and cost-effective production process for thermoelectric materials.

Recycling of nickel-metal hydride battery scrap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyman, J.W.; Palmer, G.R.

1994-12-31

Nickel-metal hydride (Ni-MH) battery technology is being developed as a NiCd replacement for applications in consumer cells and electric vehicle batteries. The U.S. Bureau of Mines is investigating hydrometallurgical recycling technology that separates and recovers individual components from Ni-MH battery scrap. Acid dissolution and metal recovery techniques such as precipitation and solvent extraction produced purified products of rare-earths, nickel, and other metals associated with AB{sub 2} and AB{sub 5} Ni-MH scrap. Tests were conducted on scrap cells of a single chemistry that had been de-canned to reduce iron content. Although recovery techniques have been identified in principal, their applicability tomore » mixed battery waste stream and economic attractiveness remain to be demonstrated. 14 refs.« less

Skid resistance study : final report.

DOT National Transportation Integrated Search

1977-06-01

This is a report of a research project involving, in Phase I, the skid resistance of asphaltic concrete overlays. Phase II is a report of a pilot study set up in order to determine the best way to perform a skid resistance inventory of the highway ne...

Influencing factors and kinetics analysis on the leaching of iron from boron carbide waste-scrap with ultrasound-assisted method.

PubMed

Li, Xin; Xing, Pengfei; Du, Xinghong; Gao, Shuaibo; Chen, Chen

2017-09-01

In this paper, the ultrasound-assisted leaching of iron from boron carbide waste-scrap was investigated and the optimization of different influencing factors had also been performed. The factors investigated were acid concentration, liquid-solid ratio, leaching temperature, ultrasonic power and frequency. The leaching of iron with conventional method at various temperatures was also performed. The results show the maximum iron leaching ratios are 87.4%, 94.5% for 80min-leaching with conventional method and 50min-leaching with ultrasound assistance, respectively. The leaching of waste-scrap with conventional method fits the chemical reaction-controlled model. The leaching with ultrasound assistance fits chemical reaction-controlled model, diffusion-controlled model for the first stage and second stage, respectively. The assistance of ultrasound can greatly improve the iron leaching ratio, accelerate the leaching rate, shorten leaching time and lower the residual iron, comparing with conventional method. The advantages of ultrasound-assisted leaching were also confirmed by the SEM-EDS analysis and elemental analysis of the raw material and leached solid samples. Copyright © 2017 Elsevier B.V. All rights reserved.

LANL Skid Testing Summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickson, Peter

2014-04-09

Our improved understanding of the processes occurring during complex drop / skid events has explained the previously observed scatter in skid and drop test data, and provided new insights into effective mitigation strategies. However, it has been perceived to undermine our current safety assumptions, which is inaccurate. We have no reason to believe that our safety margin from HEVR (the event of concern) is any different to that previously assumed – we just have a much better experimental and theoretical basis by which to measure it more accurately. Until this work is complete or, at least, more mature, we cannotmore » draw any conclusions on whether we are more or less safe than we thought, but we know that use of cushioned surfaces, along with sensible housekeeping, mitigates the potential activation of the skid-grit mechanism.« less

Mor-Bell Logger: Skidding Case Study

Treesearch

Bryce J. Stokes; Jerry L. Koger; Frank J. Pickle

1983-01-01

A production equation was developed for the Mor-Bell logger for skidding while thinning a loblolly pine plantation. Production and costs for skidding and iron gate delimbing were determined for a range of operating conditions.

Soil Wetness Influences Log Skidding

Treesearch

William N. Darwin

1960-01-01

One of the least explored variables in timber harvesting is the effect of ground conditions on log production . The Southern Hardwoods Laboratory is studying this variable and its influence on performance of skidding vehicles in Southern bottom lands. The test reported here was designed to evaluate the effects of bark features on skidding coefficients, but it also...

Recycling of rare earth metals from rare earth-transition metal alloy scrap by liquid metal extraction

DOEpatents

Ellis, Timothy W.; Schmidt, Frederick A.

1995-08-01

Method of treating rare earth metal-bearing scrap, waste or other material (e.g. Nd--Fe--B or Dy--Tb--Fe scrap) to recover the rare earth metal comprising melting the rare earth metal-bearing material, melting a Group IIA metal extractant, such as Mg, Ca, or Ba, in which the rare earth is soluble in the molten state, and contacting the melted material and melted extractant at a temperature and for a time effective to extract the rare earth from the melted material into the melted extractant. The rare earth metal is separated from the extractant metal by vacuum sublimation or distillation.

Variations in skid resistance over time.

DOT National Transportation Integrated Search

1980-01-01

The purpose of this project was to quantify the magnitude of changes in skid resistance over time, to isolate the variables that seem most important with respect to the changes, and, to the degree possible, formulate a model for converting skid resis...

Method for treating rare earth-transition metal scrap

DOEpatents

Schmidt, Frederick A.; Peterson, David T.; Wheelock, John T.; Jones, Lawrence L.

1992-12-29

Rare earth-transition metal (e.g., iron) scrap (e.g., Nd-Fe-B scrap) is flux (slag) remelted to reduce tramp non-metallic impurities, such as oxygen and nitrogen, and metallic impurities, such as Li, Na, Al, etc., picked up by the scrap from previous fabrication operations. The tramp impurities are reduced to concentrations acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets. The scrap is electroslag or inductoslag melted using a prefused, rare earth fluoride-bearing flux of CaF.sub.2, CaCl.sub.2 or mixtures thereof or the slag resulting from practice of the thermite reduction process to make a rare earth-iron alloy.

Method for treating rare earth-transition metal scrap

DOEpatents

Schmidt, F.A.; Peterson, D.T.; Wheelock, J.T.; Jones, L.L.

1992-12-29

Rare earth-transition metal (e.g., iron) scrap (e.g., Nd-Fe-B scrap) is flux (slag) remelted to reduce tramp non-metallic impurities, such as oxygen and nitrogen, and metallic impurities, such as Li, Na, Al, etc., picked up by the scrap from previous fabrication operations. The tramp impurities are reduced to concentrations acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets. The scrap is electroslag or inductoslag melted using a rare earth fluoride-bearing flux of CaF[sub 2], CaCl[sub 2] or mixtures thereof or the slag resulting from practice of the thermite reduction process to make a rare earth-iron alloy. 3 figs.

Changes in soil bulk density resulting from construction and conventional cable skidding using preplanned skid trails

Treesearch

Jingxin Wang; Chris B. LeDoux; Pam Edwards

2007-01-01

A harvesting system consisting of chainsaw felling and cable skidder extraction was studied to determine soil bulk density changes in a central Appalachian hardwood forest site. Soil bulk density was measured using a nuclear gauge preharvest and postharvest systematically across the harvest site, on transects across skid trails, and for a subset of skid trail transects...

INTERIOR VIEW WITH SCRAP HAULER DUMPING SCRAP INTO QBOP FURNACE. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW WITH SCRAP HAULER DUMPING SCRAP INTO Q-BOP FURNACE. SCRAP HAULER IS GREGORY JACKS. FURNACEMAN IS VINCENT MOREL. - U.S. Steel, Fairfield Works, Q-Bop Furnace, North of Valley Road & West of Ensley, Pleasant Grove Road, Fairfield, Jefferson County, AL

Recycling of rare earth metals from rare earth-transition metal alloy scrap by liquid metal extraction

DOEpatents

Ellis, T.W.; Schmidt, F.A.

1995-08-01

A method is described for treating rare earth metal-bearing scrap, waste or other material (e.g. Nd--Fe--B or Dy--Tb--Fe scrap) to recover the rare earth metal comprising melting the rare earth metal-bearing material, melting a Group IIA metal extractant, such as Mg, Ca, or Ba, in which the rare earth is soluble in the molten state, and contacting the melted material and melted extractant at a temperature and for a time effective to extract the rare earth from the melted material into the melted extractant. The rare earth metal is separated from the extractant metal by vacuum sublimation or distillation. 2 figs.

Skidding Coefficients on an Alluvial Soil

Treesearch

W. N. Darwin

1965-01-01

The Southern Hardwoods Laboratory is studying the influence of ground conditions and load characteristics on the performance of skidding vehicles in southern bottom lands. The exploratory test was aimed at evaluating the effects of bark on skidding coefficients, but it also yielded information on other log characteristics and on effects of soil moisture.

Estimation of Skidding Offered by Ackermann Mechanism

NASA Astrophysics Data System (ADS)

Rao, Are Padma; Venkatachalam, Rapur

2016-04-01

Steering for a four wheeler is being provided by Ackermann mechanism. Though it cannot always provide correct steering conditions, it is very popular because of its simple nature. A correct steering would avoid skidding of the tires, and thereby enhance their lives as the wear of the tires is reduced. In this paper it is intended to analyze Ackermann mechanism for its performance. A method of estimating skidding due to improper steering is proposed. Two parameters are identified using which the length of skidding can be estimated.

Acceptance test report for portable exhauster POR-007/Skid E

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kriskovich, J.R.

1998-07-24

This document describes Acceptance Testing performed on Portable Exhauster POR-007/Skid E. It includes measurements of bearing vibration levels, pressure decay testing, programmable logic controller interlocks, high vacuum, flow and pressure control functional testing. The purpose of Acceptance testing documented by this report was to demonstrate compliance of the exhausters with the performance criteria established within HNF-0490, Rev. 1 following a repair and upgrade effort at Hanford. In addition, data obtained during this testing is required for the resolution of outstanding Non-conformance Reports (NCR), and finally, to demonstrate the functionality of the associated software for the pressure control and high vacuummore » exhauster operating modes provided for by W-320. Additional testing not required by the ATP was also performed to assist in the disposition and close out of receiving inspection report and for application design information (system curve). Results of this testing are also captured within this document.« less

INTERIOR VIEW WITH SCRAP HAULER DUMPING SCRAP (C. 100,000 TONS) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW WITH SCRAP HAULER DUMPING SCRAP (C. 100,000 TONS) INTO Q-BOP FURNACE. SCRAP HAULER IS GREGORY JACKS AND FURNACEMAN, VINCENT MOREL. - U.S. Steel, Fairfield Works, Q-Bop Furnace, North of Valley Road & West of Ensley, Pleasant Grove Road, Fairfield, Jefferson County, AL

Friction and wear characteristics of wire-brush skids

NASA Technical Reports Server (NTRS)

Dreher, R. C.

1979-01-01

The testing technique consisted of towing the skids with a ground test vehicle over asphalt and concrete surfaces at ground speeds up to 80 km/hr (50 mph) and bearing pressures up to 689 kPa (100 psi) over sliding distances up to 1585 m (5200 ft). Results indicate that the friction coefficient developed by wire brush skids is essentially independent of ground speed, is slightly increased with increasing bearing pressure, is noticeably affected by surface texture, and is not degraded by surface wetness. Skid wear is shown to increase with increasing bearing pressure and with increasing ground speed and is dependent on the nature of the surface. Runway surface damage caused by the skids was in the form of an abrasive scrubbing action rather than physical damage.

The effect of contaminant on skid resistance of pavement surface

NASA Astrophysics Data System (ADS)

Lubis, A. S.; Muis, Z. A.; Gultom, E. M.

2018-03-01

Skid resistance of the pavement surface is the force generated by the movement of the wheels of the vehicle on the surface of the pavement. Contaminants are materials that cover the surface of the pavement affecting the skid resistance of the pavement surface. The contaminant acts as a coating interface or direct contact of the pavement surface with the wheels of the vehicle which can cause adverse effects, such as the decreasing value of skid resistance of the pavement surface. This study aims to analyze the effect of some types of contaminants on skid resistance of pavement surfaces. The contaminants that used in this study were water, sand, salt, and lubricating oil. The study was conducted by direct testing on two types of pavement: flexible pavement and rigid pavement. The measurements of the skid resistance were made using the British Pendulum Tester with British Pendulum Number for two conditions: before and after the pavement surface was covered with contaminants. The results showed that there was a contaminant effect on skid resistance of pavement surface. Skid resistance of pavement surfaces decreased after the contaminants were covered in water, sand, salt, and lubricant by 20.1%, 22.8%, 37.1% and 50.5% respectively.

Evaluation of skid test automatic digital recording system.

DOT National Transportation Integrated Search

1974-01-01

The Virginia skid vehicle has been equipped with a digital data recording system to provide rapid reduction of skid measurement data. It was found that five to ten minutes are required to evaluate a single measurement using the original analog strip ...

EPA and GSA Webinar: E Scrap Management, Computers for Learning and the Federal Green Challenge

EPA Pesticide Factsheets

EPA and the General Services Administration (GSA) are hosting a webinar on May 2, 2018. Topics will include policies and procedures on E Scrap management, a review of the Computers For Leaning Program, and benefits of joining the Federal Green Challenge.

Best management practices for erosion control from bladed skid trails

Treesearch

Charles R. Wade; W. Michael Aust; M. Chad Bolding; William A. Lakel III

2012-01-01

Sediment from forest operations is primarily associated with roads and skid trails. We evaluated five skid trail closure treatments applied to bladed skid trails in the Virginia Piedmont. Closure treatments were Waterbars, Seed, Mulch, Pine slash, and Hardwood slash. Sediment traps were used to collect monthly sediment samples for one year. The Mulch, Pine slash, and...

Activated carbons from waste of oil-palm kernel shells, sawdust and tannery leather scraps and application to chromium(VI), phenol, and methylene blue dye adsorption.

PubMed

Montoya-Suarez, Sergio; Colpas-Castillo, Fredy; Meza-Fuentes, Edgardo; Rodríguez-Ruiz, Johana; Fernandez-Maestre, Roberto

2016-01-01

Phenol, chromium, and dyes are continuously dumped into water bodies; the adsorption of these contaminants on activated carbon is a low-cost alternative for water remediation. We synthesized activated carbons from industrial waste of palm oil seed husks (kernel shells), sawdust, and tannery leather scraps. These materials were heated for 24 h at 600, 700 or 800°C, activated at 900°C with CO2 and characterized by proximate analysis and measurement of specific surface area (Brunauer-Emmett-Teller (BET) and Langmuir), and microporosity (t-plot). Isotherms showed micropores and mesopores in activated carbons. Palm seed activated carbon showed the highest fixed carbon content (96%), and Langmuir specific surface areas up to 1,268 m2/g, higher than those from sawdust (581 m2/g) and leather scraps (400 m2/g). The carbons were applied to adsorption of Cr(VI), phenol, and methylene blue dye from aqueous solutions. Phenol adsorption on activated carbons was 78-82 mg/g; on palm seed activated carbons, Cr(VI) adsorption at pH 7 was 0.35-0.37 mg/g, and methylene blue adsorption was 40-110 mg/g, higher than those from sawdust and leather scraps. Activated carbons from palm seed are promising materials to remove contaminants from the environment and represent an alternative application for vegetal wastes instead of dumping into landfills.

Management of MSW in Spain and recovery of packaging steel scrap.

PubMed

Tayibi, Hanan; Peña, Carmen; López, Félix A; López-Delgado, Aurora

2007-01-01

Packaging steel is more advantageously recovered and recycled than other packaging material due to its magnetic properties. The steel used for packaging is of high quality, and post-consumer waste therefore produces high-grade ferrous scrap. Recycling is thus an important issue for reducing raw material consumption, including iron ore, coal and energy. Household refuse management consists of collection/disposal, transport, and processing and treatment - incineration and composting being the most widely used methods in Spain. Total Spanish MSW production exceeds 21 million tons per year, of which 28.1% and 6.2% are treated in compost and incineration plants, respectively. This paper presents a comprehensive study of incineration and compost plants in Spain, including a review of the different processes and technologies employed and the characteristics and quality of the recovered ferrous scrap. Of the total amount of packaging steel scrap recovered from MSW, 38% comes from compost plants and 14% from incineration plants. Ferrous scrap from incineration plants presents a high degree of chemical alteration as a consequence of the thermal process to which the MSW is subjected, particularly the conditions in which the slag is cooled, and accordingly its quality diminishes. Fragmentation and magnetic separation processes produce an enhancement of the scrap quality. Ferrous scrap from compost plants has a high tin content, which negatively affects its recycling. Cleaning and detinning processes are required prior to recycling.

Vehicle speed affects both pre-skid braking kinematics and average tire/roadway friction.

PubMed

Heinrichs, Bradley E; Allin, Boyd D; Bowler, James J; Siegmund, Gunter P

2004-09-01

Vehicles decelerate between brake application and skid onset. To better estimate a vehicle's speed and position at brake application, we investigated how vehicle deceleration varied with initial speed during both the pre-skid and skidding intervals on dry asphalt. Skid-to-stop tests were performed from four initial speeds (20, 40, 60, and 80 km/h) using three different grades of tire (economy, touring, and performance) on a single vehicle and a single road surface. Average skidding friction was found to vary with initial speed and tire type. The post-brake/pre-skid speed loss, elapsed time, distance travelled, and effective friction were found to vary with initial speed. Based on these data, a method using skid mark length to predict vehicle speed and position at brake application rather than skid onset was shown to improve estimates of initial vehicle speed by up to 10 km/h and estimates of vehicle position at brake application by up to 8 m compared to conventional methods that ignore the post-brake/pre-skid interval. Copyright 2003 Elsevier Ltd.

Rare earth-transition metal scrap treatment method

DOEpatents

Schmidt, Frederick A.; Peterson, David T.; Wheelock, John T.; Jones, Lawrence L.; Lincoln, Lanny P.

1992-02-11

Rare earth-transition metal (e.g. iron) scrap (e.g. Nd-Fe-B scrap) is melted to reduce the levels of tramp oxygen and nitrogen impurities therein. The tramp impurities are reduced in the melt by virtue of the reaction of the tramp impurities and the rare earth to form dross on the melt. The purified melt is separated from the dross for reuse. The oxygen and nitrogen of the melt are reduced to levels acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets.

Rare earth-transition metal scrap treatment method

DOEpatents

Schmidt, F.A.; Peterson, D.T.; Wheelock, J.T.; Jones, L.L.; Lincoln, L.P.

1992-02-11

Rare earth-transition metal (e.g. iron) scrap (e.g. Nd-Fe-B scrap) is melted to reduce the levels of tramp oxygen and nitrogen impurities therein. The tramp impurities are reduced in the melt by virtue of the reaction of the tramp impurities and the rare earth to form dross on the melt. The purified melt is separated from the dross for reuse. The oxygen and nitrogen of the melt are reduced to levels acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets. 3 figs.

Surface radiological investigations at White Wing Scrap Yard, Oak Ridge Reservation, Oak Ridge, Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, J.K.; Rodriguez, R.E.; Uziel, M.S.

1991-09-01

A surface radiological scoping survey of accessible areas at the White Wing Scrap Yard (Waste Area Grouping 11 (WAG 11)) was conducted intermittently from December 1989 through July 1991 by members of the Measurement Applications and Development Group, Health and Safety Research Division, Oak Ridge National Laboratory (ORNL) at the request of Environmental Restoration Program personnel at ORNL. The White Wing Scrap Yard is an estimated 30-acre, predominately wooded area located on the western edge of East Fork Ridge in the McNew Hollow area on the US Department of Energy's Oak Ridge Reservation. The scrap yard was formerly used formore » aboveground storage of contaminated material (e.g., steel tanks, metal, glass, concrete, and miscellaneous industrial trash) from the Oak Ridge K-25 Site, Oak Ridge Y-12 Plant, and ORNL. The purposes of this cursory investigation were (1) to provide an updated contamination status of the site by locating and interpreting the presence, nature, and extent of surface radiological contamination and (2) to provide a basis for the formulation of interim corrective action to limit human exposures to radioactivity and minimize the potential for contaminant dispersion. 13 refs., 17 figs., 5 tabs.« less

Effectiveness and costs of overland skid trail BMPs

Treesearch

Clay Sawyers; W. Michael Aust; M. Chad Bolding; William A. Lakel III

2012-01-01

Forestry Best Management Practices (BMPs) are designed to protect water quality; however, little data exists comparing the efficacy and costs of different BMP options for skid trail closure. Study objectives were to evaluate erosion control effectiveness and implementation costs of five overland skid trail closure techniques. Closure techniques were: waterbar only (...

Recycling of metal bearing electronic scrap in a plasma furnace

NASA Astrophysics Data System (ADS)

Jarosz, Piotr; Małecki, Stanisław; Gargul, Krzysztof

2011-12-01

The recycling of electronic waste and the recovery of valuable components are large problems in the modern world economy. This paper presents the effects of melting sorted electronic scrap in a plasma furnace. Printed circuit boards, cables, and windings were processed separately. The characteristics of the obtained products (i.e., alloy metal, slag, dust, and gases) are presented. A method of their further processing in order to obtain commercial products is proposed. Because of the chemical composition and physical properties, the waste slag is environmentally inert and can be used for the production of abrasives. Process dusts containing large amounts of carbon and its compounds have a high calorific value. That makes it possible to use them for energy generation. The gas has a high calorific value, and its afterburning combined with energy recovery is necessary.

Evaluation of radioactive scrap metal recycling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nieves, L.A.; Chen, S.Y.; Kohout, E.J.

1995-12-01

This report evaluates the human health risks and environmental and socio-political impacts of options for recycling radioactive scrap metal (RSM) or disposing of and replacing it. Argonne National Laboratory (ANL) is assisting the US Department of Energy (DOE), Office of Environmental Restoration and Waste Management, Oak Ridge Programs Division, in assessing the implications of RSM management alternatives. This study is intended to support the DOE contribution to a study of metal recycling being conducted by the Task Group on Recycling and Reuse of the Organization for Economic Cooperation and Development. The focus is on evaluating the justification for the practicemore » of recycling RSM, and the case of iron and steel scrap is used as an example in assessing the impacts. To conduct the evaluation, a considerable set of data was compiled and developed. Much of this information is included in this document to provide a source book of information.« less

Test procedures and data input techniques for skid testing.

DOT National Transportation Integrated Search

1974-01-01

The purpose of this report is to describe the system for obtaining and handling skid data, including skid testing procedures and data input procedures. While all testing devices used in Virginia are covered (other than the British portable tester), t...

Recovering heavy rare earth metals from magnet scrap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ott, Ryan T.; McCallum, Ralph W.; Jones, Lawrence L.

A method of treating rare earth metal-bearing permanent magnet scrap, waste or other material in a manner to recover the heavy rare earth metal content separately from the light rare earth metal content. The heavy rare earth metal content can be recovered either as a heavy rare earth metal-enriched iron based alloy or as a heavy rare earth metal based alloy.

Measurement, Construction, and Maintenance of Skid-Resistant Airport Pavement Surfaces

DOT National Transportation Integrated Search

1997-03-18

This advisory circular (AC) contains guidelines and procedures for the design : and construction of skid-resistant pavement, pavement evaluation with friction : measuring equipment, and maintenance of high skid-resistant pavements. 45p.

Systematic characterization of generation and management of e-waste in China.

PubMed

Duan, Huabo; Hu, Jiukun; Tan, Quanyin; Liu, Lili; Wang, Yanjie; Li, Jinhui

2016-01-01

Over the last decade, there has been much effort to promote the management of e-waste in China. Policies have been affected to prohibit imports and to control pollution. Research has been conducted in laboratories and on large-scale industrial operations. A subsidy system to support sound e-waste recycling has been put in place. However, the handling of e-waste is still a concern in China and the issue remains unresolved. There has been relatively little work to follow up this issue or to interpret continuing problems from the perspective of sustainable development. This paper first provides a brief overview of conventional and emerging environmental pollution in Chinese "famous" e-waste dismantling areas, including Guiyu in Guangdong and Wenling in Zhejiang. Environmentalists have repeatedly proven that these areas are significantly polluted. Importing and backyard recycling are decreasing but are ongoing. Most importantly, no work is being done to treat or remediate the contaminated environmental media. The situation is exacerbated by the rising tide of e-waste generated by domestic update of various electronics. This study, therefore, employs a Sales Obsolescence Model approach to predict the generation of e-waste. When accounting for weight, approximately 8 million tons of e-waste will be generated domestically in 2015, of which around 50% is ferrous metals, followed by miscellaneous plastic (30%), copper metal and cables (8%), aluminum (5%), and others (7%). Of this, 3.6% will come from scrap PCBs and 0.2% from lead CRT glass. While more and more end-of-life electronics have been collected and treated by formal or licensed recyclers in China in terms of our analysis, many of them only have dismantling and separation activities. Hazardous e-wastes, including those from PCBs, CRT glass, and brominated flame retardant (BFR) plastics, have become problematic and probably flow to small or backyard recyclers without environmentally sound management. Traditional

93. VIEW OF LIQUID OXYGEN TOPPING TANK BEHIND SKID 9 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

93. VIEW OF LIQUID OXYGEN TOPPING TANK BEHIND SKID 9 AND GASEOUS NITROGEN TANKS BEHIND SKID 7 - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

Leaching behaviour of different scrap materials at recovery and recycling companies: full-, pilot- and lab-scale investigation.

PubMed

Blondeel, E; Chys, M; Depuydt, V; Folens, K; Du Laing, G; Verliefde, A; Van Hulle, S W H

2014-12-01

Scrap material recovery and recycling companies are confronted with waste water that has a highly fluctuating flow rate and composition. Common pollutants, such as COD, nutrients and suspended solids, potentially toxic metals, polyaromatic hydrocarbons and poly chlorinated biphenyls can exceed the discharge limits. An analysis of the leaching behaviour of different scrap materials and scrap yard sweepings was performed at full-scale, pilot-scale and lab-scale in order to find possible preventive solutions for this waste water problem. The results of these leaching tests (with concentrations that frequently exceeded the Flemish discharge limits) showed the importance of regular sweeping campaigns at the company, leak proof or covered storage of specific scrap materials and oil/water separation on particular leachates. The particulate versus dissolved fraction was also studied for the pollutants. For example, up to 98% of the polyaromatic hydrocarbons, poly chlorinated biphenyls and some metals were in the particulate form. This confirms the (potential) applicability of sedimentation and filtration techniques for the treatment of the majority of the leachates, and as such the rainwater run-off as a whole. Copyright © 2014 Elsevier Ltd. All rights reserved.

Scrap computer recycling in Taiwan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, C.H.; Chang, S.L.; Wang, K.M.

1999-07-01

It is estimated that approximately 700,000 scrap personal computers will be generated each year in Taiwan. The disposal of such a huge amount of scrap computers presents a difficult task for the island due to the scarcity of landfills and incineration facilities available locally. Also, the hazardous materials contained in the scrap computers may cause serious pollution to the environment, if they are not properly disposed. Thus, EPA of Taiwan has declared scrap personal computers as a producer responsibility recycling product on July 1997 to mandate that the manufacturers, importers and sellers of personal computers have to recover and recyclemore » their scrap computers properly. Beginning on June 1, 1998, a scrap computer recycling plan is officially implemented on the island. Under this plan, consumers can deliver their unwanted personal computers to the designated collection points to receive reward money. Currently, only six items are mandated to be recycled in this recycling plan. They are notebooks, monitor and the hard disk, power supply, printed circuit board and shell of the main frame of the personal computer. This paper presents the current scrap computer recycling system in Taiwan.« less

Sediment pathways in a tropical forest: effects of logging roads and skid trails

NASA Astrophysics Data System (ADS)

Sidle, Roy C.; Sasaki, Shozo; Otsuki, Mieko; Noguchi, Shoji; Rahim Nik, Abdul

2004-03-01

Significant erosion occurred from recently constructed forest logging roads and skid trails in a small headwater catchment in Peninsular Malaysia. Soil loss was estimated by measuring dimensions of all significant rills and gullies along the road, as well as by measuring height of preserved soil pedestals in sidecast and fill material and on skid trails. Estimates of surface erosion from logging roads and skid trails were 272 +/- 20 t ha-1 year-1 and 275 +/- 20 t ha-1 year-1 respectively. However, owing to lack of connectivity of skid trails to the stream, much of the sediment mobilized on skid trails was stored either on adjacent hillslopes or the trails themselves, rather than being transported to the stream system, as was the case for the road. Steeper skid trails (>20% gradient) had slightly higher erosion rates (320 +/- 24 t ha-1 year-1) than trails with gentler gradients (245-264 t ha-1 year-1). Some 60% of the soil loss on logging roads comes from erosion of the running surface. Disturbed cut and fill material along the road supplied the remaining 40% of the soil loss from roads. Roads and skid trails had no designed drainage systems; runoff discharged onto the hillslope at 25 major discharge nodes from the logging road (690 m total length) and at 34 nodes from skid trails (2300 m). Sediment pathways were either fully or moderately connected to headwater channels at 64% of the logging road nodes, but at only 26% of the nodes emanating from skid trails. A detailed sediment budget revealed that 78% of the soil loss from the road system (including log landings) was delivered to the stream in the first 16 months after logging began. Most (90%) of the deposition from skid trails occurred below just three discharge nodes. Runoff from and onto skid trails often exacerbated the sediment connectivity to channels. Clearly, sediment discharge from logging roads was more highly connected to the stream than discharge from skid trails. Once in the channel, much of this

Generation of urban road dust from anti-skid and asphalt concrete aggregates.

PubMed

Tervahattu, Heikki; Kupiainen, Kaarle J; Räisänen, Mika; Mäkelä, Timo; Hillamo, Risto

2006-04-30

Road dust forms an important component of airborne particulate matter in urban areas. In many winter cities the use of anti-skid aggregates and studded tires enhance the generation of mineral particles. The abrasion particles dominate the PM10 during springtime when the material deposited in snow is resuspended. This paper summarizes the results from three test series performed in a test facility to assess the factors that affect the generation of abrasion components of road dust. Concentrations, mass size distribution and composition of the particles were studied. Over 90% of the particles were aluminosilicates from either anti-skid or asphalt concrete aggregates. Mineral particles were observed mainly in the PM10 fraction, the fine fraction being 12% and submicron size being 6% of PM10 mass. The PM10 concentrations increased as a function of the amount of anti-skid aggregate dispersed. The use of anti-skid aggregate increased substantially the amount of PM10 originated from the asphalt concrete. It was concluded that anti-skid aggregate grains contribute to pavement wear. The particle size distribution of the anti-skid aggregates had great impact on PM10 emissions which were additionally enhanced by studded tires, modal composition, and texture of anti-skid aggregates. The results emphasize the interaction of tires, anti-skid aggregate, and asphalt concrete pavement in the production of dust emissions. They all must be taken into account when measures to reduce road dust are considered. The winter maintenance and springtime cleaning must be performed properly with methods which are efficient in reducing PM10 dust.

Field evaluation of skid resistant surfaces : final report : part I.

DOT National Transportation Integrated Search

1970-06-01

This project was undertaken to establish a thin bituminous surface course that would possess good skid resistant qualities as well as, being both economical and durable. : This is the final report on the evaluation of skid resistant surfaces which wa...

Alternative skid trail retirement options for steep terrain logging

Treesearch

Mathew F. Smidt; Randall K. Kolka

2001-01-01

In winter 1999-2000 trials of deep tillage and recontouring of skid trails were implemented on three sites in northeastern Kentucky, USA to examine their potential as skid trail retirement options. While effective, current Best Management Practices (BMPs) for trail retirement do not address two potential benefits of retirement: recovery of normal hill slope hydrology...

Alternative skid trail retirement options for steep terrain logging

Treesearch

Mathew F. Smidt; Randall K. Kelka

2001-01-01

In winter 1999-2000 trials of deep tillage and recontouring of skid trails were implemented on three sites in northeastern Kentucky, USA to examine their potential as skid trail retirement options. While effective, current Best Management Practices (BMPs) for trail retirement do not address two potential benefits of retirement: recovery of normal hill slope\\r\\...

A Pilot Assessment of Occupational Health Hazards in the US Electronic Scrap Recycling Industry

PubMed Central

Ceballos, Diana M.; Gong, Wei; Page, Elena

2015-01-01

The National Institute for Occupational Safety and Health (NIOSH) surveyed a randomly selected sample of electronic scrap (e-scrap) recycling facilities nationwide to characterize work processes, exposures, and controls. Despite multiple attempts to contact 278 facilities, only 47 responded (17% response rate). Surveyed facilities reported recycling a wide variety of electronics. The most common recycling processes were manual dismantling and sorting. Other processes included shredding, crushing, and automated separation. Many facilities reported that they had health and safety programs in place. However, some facilities reported the use of compressed air for cleaning, a practice that can lead to increased employee dust exposures, and some facilities allowed food and drinks in the production areas, a practice that can lead to ingestion of contaminants. Although our results may not be generalizable to all US e-scrap recycling facilities, they are informative regarding health and safety programs in the industry. We concluded that e-scrap recycling has the potential for a wide variety of occupational exposures particularly because of the frequent use of manual processes. On-site evaluations of e-scrap recyclers are needed to determine if reported work processes, practices, and controls are effective and meet current standards and guidelines. Educating the e-scrap recycling industry about health and safety best practices, specifically related to safe handling of metal dust, would help protect employees. PMID:25738822

A Pilot Assessment of Occupational Health Hazards in the US Electronic Scrap Recycling Industry.

PubMed

Ceballos, Diana M; Gong, Wei; Page, Elena

2015-01-01

The National Institute for Occupational Safety and Health (NIOSH) surveyed a randomly selected sample of electronic scrap (e-scrap) recycling facilities nationwide to characterize work processes, exposures, and controls. Despite multiple attempts to contact 278 facilities, only 47 responded (17% response rate). Surveyed facilities reported recycling a wide variety of electronics. The most common recycling processes were manual dismantling and sorting. Other processes included shredding, crushing, and automated separation. Many facilities reported that they had health and safety programs in place. However, some facilities reported the use of compressed air for cleaning, a practice that can lead to increased employee dust exposures, and some facilities allowed food and drinks in the production areas, a practice that can lead to ingestion of contaminants. Although our results may not be generalizable to all US e-scrap recycling facilities, they are informative regarding health and safety programs in the industry. We concluded that e-scrap recycling has the potential for a wide variety of occupational exposures particularly because of the frequent use of manual processes. On-site evaluations of e-scrap recyclers are needed to determine if reported work processes, practices, and controls are effective and meet current standards and guidelines. Educating the e-scrap recycling industry about health and safety best practices, specifically related to safe handling of metal dust, would help protect employees.

Skid correction program : user's manual.

DOT National Transportation Integrated Search

2012-06-01

This document outlines methods for use by UDOT personnel to address pavements with unacceptable skid numbers. The program involves coordination between Safety, Pavement Management, Region, and Maintenance managers. A process has been recommended usin...

The effect of aggregate type and mix design on the wet skid resistance of bituminous pavement : recommendations for Virginia's Wet Accident Reduction Program.

DOT National Transportation Integrated Search

1995-01-01

This report (1) identified and characterized Virginia's nonpolishing aggregates in terms of their wet skid resistance, (2) compared the standard ASTM E 274-90 skid test to the British Accelerated Polishing Machine (BAPM) and British PendulumTester (B...

Composite skid landing gear design investigation

NASA Astrophysics Data System (ADS)

Shrotri, Kshitij

A Composite Skid Landing Gear Design investigation has been conducted. Limit Drop Test as per Federal Aviation Regulations (FAR) Part 27.725 and Crash test as per MIL STD 1290A (AV) were simulated using ABAQUS to evaluate performance of multiple composite fiber-matrix systems. Load factor developed during multiple landing scenarios and energy dissipated during crash were computed. Strength and stiffness based constraints were imposed. Tsai-Wu and LaRC04 physics based failure criteria were used for limit loads. Hashin's damage initiation criteria with Davila-Camanho's energy based damage evolution damage evolution law were used for crash. Initial results indicate that all single-composite skid landing gear may no be feasible due to strength concerns in the cross member bends. Hybridization of multiple composites with elasto-plastic aluminum 7075 showed proof of strength under limit loads. Laminate tailoring for load factor optimization under limit loads was done by parameterization of a single variable fiber orientation angle for multiple laminate families. Tsai-Wu failure criterion was used to impose strength contraints. A quasi-isotropic N = 4 (pi/4) 48 ply IM7/8552 laminate was shown to be the optimal solution with a load failure will be initiated as matrix cracking under compression and fiber kinking under in-plane shear and longitudinal compression. All failures under limit loads being reported in the metal-composite hybrid joint region, the joint was simulated by adhesive bonding and filament winding, separately. Simply adhesive bonding the metal and composite regions does not meet strength requirements. A filament wound metal-composite joint shows proof of strength. Filament wound bolted metal-composite joint shows proof of strength. Filament wound composite bolted to metal cross member radii is the final joining methodology. Finally, crash analysis was conducted as per requirements from MIL STD 1290A (AV). Crash at 42 ft/sec with 1 design gross weight (DGW

Characterization of brominated flame retardants from e-waste components in China.

PubMed

Yu, Danfeng; Duan, Huabo; Song, Qingbin; Liu, Yicheng; Li, Ying; Li, Jinhui; Shen, Weijun; Luo, Jiahui; Wang, Jinben

2017-10-01

Many studies show that high levels of many toxic metals and persistent and bio-accumulative chemicals have been found in electronic waste (e-waste) dismantling sites and their surrounding environmental media. Both flame-retardant plastic housing materials and printed circuit boards (PCBs) could be the major contributors. However, relatively little work has focused on the use or content of toxic substances and their changing in scrap housing materials and PCBs from home appliances. This study evaluated the existence of brominated flame retardants (BFRs, including polybrominated diphenyl ethers (PBDEs) and Tetrabromobisphenol-A (TBBPA)) in housing plastics and PCBs from home appliances collected from various e-waste recyclers in China. These were then analyzed for the potential migration of BFRs from the e-waste components into their recycled products. The results show that both PBDEs and TBBPA were found with high level in most of e-waste samples, indicating that the widespread use of BFRs in home appliances are entering into the end-of-life stage. For the plastics samples, CRT TVs and LCD monitors should be given priority for the control of BFRs. Regarding PBDEs, the dominant congeners of BDE-209 in the plastics samples contributed 90.72-93.54% to the total concentrations of PBDEs, yet there are large variations for PCBs samples: BDE-28, -47, -99, and -153 were also important congeners compositions, except for BDE-209. Compared with previous studies, the BFRs concentrations in current Chinese e-waste are trending to decline. This study also found that BFRs in housing plastics and PCBs will be transferred into the recycled products with other purpose use, and the new products could have highly enriched capacities for BFRs. The obtained results could be helpful to manage e-waste and their components properly in order to minimize associated environmental and health risks of BFRs, particularly for their further reuse. Copyright © 2017 Elsevier Ltd. All rights reserved.

Orbiter post-tire failure and skid testing results

NASA Technical Reports Server (NTRS)

Daugherty, Robert H.; Stubbs, Sandy M.

1989-01-01

An investigation was conducted at the NASA Langley Research Center's Aircraft Landing Dynamics Facility (ALDF) to define the post-tire failure drag characteristics of the Space Shuttle Orbiter main tire and wheel assembly. Skid tests on various materials were also conducted to define their friction and wear rate characteristics under higher speed and bearing pressures than any previous tests. The skid tests were conducted to support a feasibility study of adding a skid to the orbiter strut between the main tires to protect an intact tire from failure due to overload should one of the tires fail. Roll-on-rim tests were conducted to define the ability of a standard and a modified orbiter main wheel to roll without a tire. Results of the investigation are combined into a generic model of strut drag versus time under failure conditions for inclusion into rollout simulators used to train the shuttle astronauts.

Surface debris inventory at White Wing Scrap Yard, Oak Ridge Reservation, Oak Ridge, Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez, R.E.; Tiner, P.F.; Williams, J.K.

1992-08-01

An inventory of surface debris in designated grid blocks at the White Wing Scrap Yard [Waste Area Grouping 11 (WAG 11)] was conducted intermittently from February through June 1992 by members of the Measurement Applications and Development Group, Health and Safety Research Division, Oak Ridge National Laboratory (ORNL) at the request of ORNL Environmental Restoration (ER) Program personnel. The objectives of this project are outlined in the following four phases: (1) estimate the amount (volume) and type (e.g., glass, metal and plastics) of surface waste material in 30 designated grid blocks (100- by 100-ft grids); (2) conduct limited air samplingmore » for organic chemical pollutants at selected locations (e.g., near drums, in holes, or other potentially contaminated areas); (3) conduct a walkover gamma radiation scan extending outward (approximately 50 ft) beyond the proposed location of the WAG 11 perimeter fence; and (4) recommend one grid block as a waste staging area. This recommendation is based on location and accessibility for debris staging/transport activities and on low levels of gamma radiation in the grid block.« less

Method for recovery of actinides from actinide-bearing scrap and waste nuclear material using O/sub 2/F/sub 2/

DOEpatents

Asprey, L.B.; Eller, P.G.

1984-09-12

Method for recovery of actinides from nuclear waste material containing sintered and other oxides thereof and from scrap materials containing the metal actinides using O/sub 2/F/sub 2/ to generate the hexafluorides of the actinides present therein. The fluorinating agent, O/sub 2/F/sub 2/, has been observed to perform the above-described tasks at sufficiently low temperatures that there is virtually no damage to the containment vessels. Moreover, the resulting actinide hexafluorides are not detroyed by high temperature reactions with the walls of the reaction vessel. Dioxygen difluoride is readily prepared, stored and transferred to the place of reaction.

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid Q

DOE Office of Scientific and Technical Information (OSTI.GOV)

KOCH, M.R.

2000-03-27

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''Q''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.

7 CFR 29.3652 - Scrap (S Group).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Scrap (S Group). 29.3652 Section 29.3652 Agriculture... INSPECTION Standards Grades § 29.3652 Scrap (S Group). A byproduct of stemmed and unstemmed tobacco. Scrap... stemmeries. Grades Grade name and specifications S Scrap. Loose, tangled, whole, or broken unstemmed leaves...

7 CFR 29.1169 - Scrap (S Group).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Scrap (S Group). 29.1169 Section 29.1169 Agriculture... INSPECTION Standards Grades § 29.1169 Scrap (S Group). A byproduct of stemmed and unstemmed tobacco. Scrap... stemmeries. Grade, Grade Name and Specifications S—Scrap. Loose, whole, or broken unstemmed leaves; or the...

7 CFR 29.2666 - Scrap (S Group).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Scrap (S Group). 29.2666 Section 29.2666 Agriculture... INSPECTION Standards Grades § 29.2666 Scrap (S Group). A byproduct of unstemmed and stemmed tobacco. Scrap... stemmeries. Grades Grade names and specifications S Scrap. Tangled, whole, or broken unstemmed leaves, or the...

The general utilization of scrapped PC board.

PubMed

Liu, Robert; Shieh, R S; Yeh, Ruth Y L; Lin, C H

2009-11-01

The traditional burning process is used to recover copper from scrapped PC board (printed circuit board) but it causes serious environmental problems. In this research a new process was developed which not only prevents pollution problems, but also maximizes the utility of all the materials on the waste board. First, the scrapped PC board was crushed and grounded, then placed in the NH3/NH5CO3 solution with aeration in order to dissolve copper. After distilling the copper NH3/NH5CO3 solution and then heating the distilled residue of copper carbonate, pure copper oxide was obtained with particle size of about 0.2 microm and the shape elliptical. The remaining solid residue after copper removal was then leached with 6N hydrochloric acid to remove tin and lead. The last residue was used as a filler in PVC plastics. The PVC plastics with PC board powder as filling material was found to have the same tensile strength as unfilled plastics, but had higher elastic modulus, higher abrasion resistance, and was cheaper.

7 CFR 29.6022 - Leaf scrap.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Leaf scrap. 29.6022 Section 29.6022 Agriculture... INSPECTION Standards Definitions § 29.6022 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. ...

7 CFR 29.6022 - Leaf scrap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.6022 Section 29.6022 Agriculture... INSPECTION Standards Definitions § 29.6022 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. ...

7 CFR 29.6022 - Leaf scrap.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Leaf scrap. 29.6022 Section 29.6022 Agriculture... INSPECTION Standards Definitions § 29.6022 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. ...

7 CFR 29.6022 - Leaf scrap.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Leaf scrap. 29.6022 Section 29.6022 Agriculture... INSPECTION Standards Definitions § 29.6022 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. ...

7 CFR 29.6022 - Leaf scrap.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Leaf scrap. 29.6022 Section 29.6022 Agriculture... INSPECTION Standards Definitions § 29.6022 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. ...

7 CFR 29.2277 - Leaf scrap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.2277 Section 29.2277 Agriculture... INSPECTION Standards Official Standard Grades for Virginia Fire-Cured Tobacco (u.s. Type 21) § 29.2277 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists...

7 CFR 29.2277 - Leaf scrap.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Leaf scrap. 29.2277 Section 29.2277 Agriculture... INSPECTION Standards Official Standard Grades for Virginia Fire-Cured Tobacco (u.s. Type 21) § 29.2277 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists...

7 CFR 29.2277 - Leaf scrap.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Leaf scrap. 29.2277 Section 29.2277 Agriculture... INSPECTION Standards Official Standard Grades for Virginia Fire-Cured Tobacco (u.s. Type 21) § 29.2277 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists...

7 CFR 29.2277 - Leaf scrap.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Leaf scrap. 29.2277 Section 29.2277 Agriculture... INSPECTION Standards Official Standard Grades for Virginia Fire-Cured Tobacco (u.s. Type 21) § 29.2277 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists...

7 CFR 29.2277 - Leaf scrap.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Leaf scrap. 29.2277 Section 29.2277 Agriculture... INSPECTION Standards Official Standard Grades for Virginia Fire-Cured Tobacco (u.s. Type 21) § 29.2277 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists...

Environmental risk related to specific processes during scrap computer recycling and disposal.

PubMed

Li, Jinhui; Shi, Pixing; Shan, Hongshan; Xie, Yijun

2012-12-01

The purpose of this work was to achieve a better understanding of the generation of toxic chemicals related to specific processes in scrap computer recycling and disposal, such as thermal recycling of printed circuit boards (PCBs) and the landfilling or dumping of cathode ray tubes (CRTs). Tube furnace pyrolysis was carried out to simulate different thermal treatment conditions for the identification of the by-products and potential environmental risk from thermal recycling ofPCBs. The Toxicity Characteristic Leaching Procedure (TCLP) and a column test were used to study the leaching characteristics of lead from waste CRT glass, which is one of the most important environmental concerns arising from the disposal of e-waste. The results indicate that more attention should be paid to the benzene series when recycling PCBs under thermal conditions, especially for workers without any personal protection equipment. The impact of immersion on the leaching of lead from CRT leaded glass was more effective than the impact of washing only by acid rain. Thus when waste leaded glass has to be stored for some reason, the storage facility should be dry.

An adaptable walking-skid for seabed ROV under strong current disturbance

NASA Astrophysics Data System (ADS)

Si, Jianting; Chin, Chengsiong

2014-09-01

This paper proposed a new concept of an adaptable multi-legged skid design for retro-fitting to a remotely-operated vehicle (ROV) during high tidal current underwater pipeline inspection. The sole reliance on propeller-driven propulsion for ROV is replaced with a proposed low cost biomimetic solution in the form of an attachable hexapod walking skid. The advantage of this adaptable walking skid is the high stability in positioning and endurances to strong current on the seabed environment. The computer simulation flow studies using Solidworks Flow Simulation shown that the skid attachment in different compensation postures caused at least four times increase in overall drag, and negative lift forces on the seabed ROV to achieve a better maneuvering and station keeping under the high current condition (from 0.5 m/s to 5.0 m/s). A graphical user interface is designed to interact with the user during robot-in-the-loop testing and kinematics simulation in the pool.

Methodology for utilizing survey skid data.

DOT National Transportation Integrated Search

1975-01-01

This report sets forth procedures for utilizing survey skid data with consideration given to testing variabilities and relationships between the three testing devices used in Virginia namely, the Virginia Department of Highways & Transportation's tra...

7 CFR 29.3526 - Leaf scrap.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Leaf scrap. 29.3526 Section 29.3526 Agriculture... Type 95) § 29.3526 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [30 FR 9207, July 23, 1965...

7 CFR 29.3526 - Leaf scrap.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Leaf scrap. 29.3526 Section 29.3526 Agriculture... Type 95) § 29.3526 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [30 FR 9207, July 23, 1965...

7 CFR 29.3526 - Leaf scrap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.3526 Section 29.3526 Agriculture... Type 95) § 29.3526 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [30 FR 9207, July 23, 1965...

7 CFR 29.3034 - Leaf scrap.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Leaf scrap. 29.3034 Section 29.3034 Agriculture... Leaf scrap. A by-product of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [24 FR 8771, Oct. 29, 1959. Redesignated at 49 FR...

7 CFR 29.3034 - Leaf scrap.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Leaf scrap. 29.3034 Section 29.3034 Agriculture... Leaf scrap. A by-product of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [24 FR 8771, Oct. 29, 1959. Redesignated at 49 FR...

7 CFR 29.3526 - Leaf scrap.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Leaf scrap. 29.3526 Section 29.3526 Agriculture... Type 95) § 29.3526 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [30 FR 9207, July 23, 1965...

7 CFR 29.3034 - Leaf scrap.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Leaf scrap. 29.3034 Section 29.3034 Agriculture... Leaf scrap. A by-product of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [24 FR 8771, Oct. 29, 1959. Redesignated at 49 FR...

7 CFR 29.3034 - Leaf scrap.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Leaf scrap. 29.3034 Section 29.3034 Agriculture... Leaf scrap. A by-product of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [24 FR 8771, Oct. 29, 1959. Redesignated at 49 FR...

7 CFR 29.3034 - Leaf scrap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.3034 Section 29.3034 Agriculture... Leaf scrap. A by-product of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [24 FR 8771, Oct. 29, 1959. Redesignated at 49 FR...

7 CFR 29.3526 - Leaf scrap.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Leaf scrap. 29.3526 Section 29.3526 Agriculture... Type 95) § 29.3526 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or broken leaves. [30 FR 9207, July 23, 1965...

Immobilisation of Cu, Pb and Zn in Scrap Metal Yard Soil Using Selected Waste Materials.

PubMed

Kamari, A; Putra, W P; Yusoff, S N M; Ishak, C F; Hashim, N; Mohamed, A; Isa, I M; Bakar, S A

2015-12-01

Immobilisation of heavy metals in a 30-year old active scrap metal yard soil using three waste materials, namely coconut tree sawdust (CTS), sugarcane bagasse (SB) and eggshell (ES) was investigated. The contaminated soil was amended with amendments at application rates of 0 %, 1 % and 3 % (w/w). The effects of amendments on metal accumulation in water spinach (Ipomoea aquatica) and soil metal bioavailability were studied in a pot experiment. All amendments increased biomass yield and reduced metal accumulation in the plant shoots. The bioconcentration factor and translocation factor values of the metals were in the order of Zn > Cu > Pb. The addition of ES, an alternative source of calcium carbonate (CaCO3), has significantly increased soil pH and resulted in marked reduction in soil metal bioavailability. Therefore, CTS, SB and ES are promising low-cost immobilising agents to restore metal contaminated land.

Cost of skid roads for arch logging in West Virginia

Treesearch

George R., Jr. Trimble; Carl R. Barr

1960-01-01

In the mountain hardwood country of the northern Appalachians, tree-length skidding with tractor and arch has proved to be economical logging. One essential part of this type of logging is that tree-length logs are winched to the skid roads: tractor and arch do not run around through the woods. Winching distance is commonly 200 to 300 feet; and occasionally an extra...

A decision algorithm for determining safe clearing limits for the construction of skid roads

Treesearch

Chris LeDoux

2006-01-01

The majority of the timber harvested in the United States is extracted by ground-based skidders and crawler/dozer systems. Ground-based systems generally require a primary transportation network (a network of skid trails/roads) throughout the area being harvested. Logs are skidded or dragged along these skid roads/trails as they are transported from where they were cut...

7 CFR 29.2529 - Leaf scrap.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Leaf scrap. 29.2529 Section 29.2529 Agriculture...-Cured Tobacco (u.s. Types 22, 23, and Foreign Type 96) § 29.2529 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or...

7 CFR 29.2529 - Leaf scrap.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Leaf scrap. 29.2529 Section 29.2529 Agriculture...-Cured Tobacco (u.s. Types 22, 23, and Foreign Type 96) § 29.2529 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or...

7 CFR 29.2529 - Leaf scrap.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Leaf scrap. 29.2529 Section 29.2529 Agriculture...-Cured Tobacco (u.s. Types 22, 23, and Foreign Type 96) § 29.2529 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or...

7 CFR 29.2529 - Leaf scrap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.2529 Section 29.2529 Agriculture...-Cured Tobacco (u.s. Types 22, 23, and Foreign Type 96) § 29.2529 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or...

7 CFR 29.2529 - Leaf scrap.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Leaf scrap. 29.2529 Section 29.2529 Agriculture...-Cured Tobacco (u.s. Types 22, 23, and Foreign Type 96) § 29.2529 Leaf scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or...

Thiosulfate leaching of gold from waste mobile phones.

PubMed

Ha, Vinh Hung; Lee, Jae-chun; Jeong, Jinki; Hai, Huynh Trung; Jha, Manis K

2010-06-15

The present communication deals with the leaching of gold from the printed circuit boards (PCBs) of waste mobile phones using an effective and less hazardous system, i.e., a copper-ammonia-thiosulfate solution, as an alternative to the conventional and toxic cyanide leaching of gold. The influence of thiosulfate, ammonia and copper sulfate concentrations on the leaching of gold from PCBs of waste mobile phones was investigated. Gold extraction was found to be enhanced with solutions containing 15-20 mM cupric, 0.1-0.14 M thiosulfate, and 0.2-0.3 M ammonia. Similar trends were obtained for the leaching of gold from two different types of scraps and PCBs of waste mobile phones. From the scrap samples, 98% of the gold was leached out using a solution containing 20 mM copper, 0.12 M thiosulfate and 0.2 M ammonia. Similarly, the leaching of gold from the PCBs samples was also found to be good, but it was lower than that of scrap samples in similar experimental conditions. In this case, only 90% of the gold was leached, even with a contact time of 10h. The obtained data will be useful for the development of processes for the recycling of gold from waste mobile phones. Copyright 2010 Elsevier B.V. All rights reserved.

A model for recovery of scrap monolithic uranium molybdenum fuel by electrorefining

NASA Astrophysics Data System (ADS)

Van Kleeck, Melissa A.

The goal of the Reduced Enrichment for Research and Test Reactors program (RERTR) is toreduce enrichment at research and test reactors, thereby decreasing proliferation risk at these facilities. A new fuel to accomplish this goal is being manufactured experimentally at the Y12 National Security Complex. This new fuel will require its own waste management procedure,namely for the recovery of scrap from its manufacture. The new fuel is a monolithic uraniummolybdenum alloy clad in zirconium. Feasibility tests were conducted in the Planar Electrode Electrorefiner using scrap U-8Mo fuel alloy. These tests proved that a uranium product could be recovered free of molybdenum from this scrap fuel by electrorefining. Tests were also conducted using U-10Mo Zr clad fuel, which confirmed that product could be recovered from a clad version of this scrap fuel at an engineering scale, though analytical results are pending for the behavior of Zr in the electrorefiner. A model was constructed for the simulation of electrorefining the scrap material produced in the manufacture of this fuel. The model was implemented on two platforms, Microsoft Excel and MatLab. Correlations, used in the model, were developed experimentally, describing area specific resistance behavior at each electrode. Experiments validating the model were conducted using scrap of U-10Mo Zr clad fuel in the Planar Electrode Electrorefiner. The results of model simulations on both platforms were compared to experimental results for the same fuel, salt and electrorefiner compositions and dimensions for two trials. In general, the model demonstrated behavior similar to experimental data but additional refinements are needed to improve its accuracy. These refinements consist of a function for surface area at anode and cathode based on charge passed. Several approximations were made in the model concerning areas of electrodes which should be replaced by a more accurate function describing these areas.

Validation of Filtration Skid During Land-Based & Shipboard Tests

DTIC Science & Technology

2012-10-12

b. ABSTRACT c. THIS PAGE 19b. TELEPHONE NUMBER (include area code) Standard Form 298 (Re . 8-98) v Prescribed by ANSI Std. Z39.18 12...skid device that it had previously developed. A prototype unit was developed and deployed on the bulk carrier M/ V Indiana Harbor, and commissioning...a preliminary design of a filter skid device that it had previously developed. A prototype unit was developed and deployed on the bulk carrier M/ V

14 CFR 29.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions... along the bottom of both skids, the vertical reactions must be applied as prescribed in paragraph (a) of this section. (c) Drag reactions in the level landing attitude. In the level attitude, and with the...

14 CFR 29.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions... along the bottom of both skids, the vertical reactions must be applied as prescribed in paragraph (a) of this section. (c) Drag reactions in the level landing attitude. In the level attitude, and with the...

14 CFR 27.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions... along the bottom of both skids, the vertical reactions must be applied as prescribed in paragraph (a) of this section. (c) Drag reactions in the level landing attitude. In the level attitude, and with the...

14 CFR 27.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions... along the bottom of both skids, the vertical reactions must be applied as prescribed in paragraph (a) of this section. (c) Drag reactions in the level landing attitude. In the level attitude, and with the...

Arc Synthesis of Fullerenes from the Carbide of Waste Cloths

NASA Astrophysics Data System (ADS)

Hayashi, Koichiro; Mieno, Tetsu

2000-09-01

A great many scraps of cotton cloth are disposed of as industrial waste through making clothes. The purpose of this study is to transform the waste into very valuable carbon compounds, that is, fullerenes. The scraps were piled and carbonized in air at 1050°C. By carbonization, the weight of the scraps decreased to 16-18%. Carbide from the scraps was used as the raw material for synthesizing fullerenes with the \\mbi{J}×\\mbi{B} arc discharge method. The soot that was deposited on the inside of the vacuum chamber contained C60 (>0.05 wt%), C70 and higher fullerenes.

7 CFR 29.3157 - Scrap (S Group).

Code of Federal Regulations, 2010 CFR

2010-01-01

... INSPECTION Standards Grades § 29.3157 Scrap (S Group). A by-product of unstemmed and stemmed tobacco. Scrap..., or web portions of tobacco leaves reduced to scrap by any process. [24 FR 8771, Oct. 29, 1959, as...

Relationships between skid numbers, paving materials and mix design, and accumulated traffic.

DOT National Transportation Integrated Search

1977-01-01

The objectives of this study were to determine the periods of time over which materials used in pavement surfaces provide adequate skid resistance and to classify various aggregate sources on the basis of the skid resistance qualities of the material...

Validation of asphalt mixture pavement skid prediction model and development of skid prediction model for surface treatments.

DOT National Transportation Integrated Search

2017-04-01

Pavement skid resistance is primarily a function of the surface texture, which includes both microtexture and macrotexture. Earlier, under the Texas Department of Transportation (TxDOT) Research Project 0-5627, the researchers developed a method to p...

Removal of copper from ferrous scrap

DOEpatents

Blander, M.; Sinha, S.N.

1987-07-30

A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

Removal of copper from ferrous scrap

DOEpatents

Blander, M.; Sinha, S.N.

1990-05-15

A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

Removal of copper from ferrous scrap

DOEpatents

Blander, Milton; Sinha, Shome N.

1990-01-01

A process for removing copper from ferrous or other metal scrap in which the scrap is contacted with a polyvalent metal sulfide slag in the presence of an excess of copper-sulfide forming additive to convert the copper to copper sulfide which is extracted into the slag to provide a ratio of copper in the slag to copper in the metal scrap of at least about 10.

Scrap automotive electronics: A mini-review of current management practices.

PubMed

Cucchiella, Federica; D'Adamo, Idiano; Rosa, Paolo; Terzi, Sergio

2016-01-01

End-of-life vehicles, together with waste from electric and electronic equipment, are known as an important source of secondary raw materials. For many years, their recovery has allowed the restoring of great amounts of metals for new cars production. This article provides a comprehensive mini-review on the end-of-life vehicles recycling topic between 2000 and 2014, with a particular focus on automotive electronics recycling. In fact, in the last years, experts focused their attention on a better exploitation of automotive shredder residue fraction, but not sufficiently on eventual electronic scraps embedded in it. Hence, studies assessing the value embedded in these scraps are rarely available in literature, causing an important gap in both recycling policies and research. The fact that, at present, the management of electronic control units (the most valuable component among automotive electronic equipment) is, as yet, off the radar in both end-of-life vehicles and waste from electric and electronic equipment Directives demonstrates the theory. Of course, their recycling would not contribute in a relevant way to reach the weighted-based recycling and recovery targets characterising current regulations, but would be very important under a critical raw materials recovery view. Results coming from the literature analysis confirm these assumptions. © The Author(s) 2015.

Morphological and mechanical analyses of laminates manufactured from randomly positioned carbon fibre/epoxy resin prepreg scraps

NASA Astrophysics Data System (ADS)

Souza, Christiane S. R.; Cândido, Geraldo M.; Alves, Wellington; Marlet, José Maria F.; Rezende, Mirabel C.

2017-10-01

This study aims to contribute to sustainability by proposing the reuse of composite prepreg scrap as an added value from discards. The research evaluates the microstructure and mechanical properties of laminates processed by the reuse of uncured carbon fibre/F155-epoxy resin prepreg scraps, waste from the ply cutting area of an aeronautical industry. The composite scraps were used as collected and were randomly positioned to produce laminates to be cured at an autoclave. The mechanical characterization shows a decrease of 39% for the compression property due to the discontinuous fibres in the laminate and an increase of 34% for the interlaminar shear strength, when compared to continuous fibre laminates. This increase is attributed to the higher crosslink density of the epoxy resin, as a result of the cure temperature used in autoclave (60 °C higher than suggested by supplier) and also to the randomly positioned scraps. Microscopic analyses confirm the consolidation of laminates, although show resin rich areas with different sizes and shapes attributed to the overlapping of the scraps with different sizes and shapes. These resin rich areas may contribute to decrease the mechanical properties of laminates. The correlation between mechanical and morphological results shows potential to be used on non-critical structural application, as composite jigs, contributing to sustainability.

7 CFR 29.1169 - Scrap (S Group).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Scrap (S Group). 29.1169 Section 29.1169 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.1169 Scrap (S Group). A byproduct of stemmed and unstemmed tobacco. Scrap...

7 CFR 29.1169 - Scrap (S Group).

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Scrap (S Group). 29.1169 Section 29.1169 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.1169 Scrap (S Group). A byproduct of stemmed and unstemmed tobacco. Scrap...

7 CFR 29.1169 - Scrap (S Group).

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Scrap (S Group). 29.1169 Section 29.1169 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.1169 Scrap (S Group). A byproduct of stemmed and unstemmed tobacco. Scrap...

7 CFR 29.3157 - Scrap (S Group).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Scrap (S Group). 29.3157 Section 29.3157 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.3157 Scrap (S Group). A by-product of unstemmed and stemmed tobacco. Scrap...

7 CFR 29.2666 - Scrap (S Group).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Scrap (S Group). 29.2666 Section 29.2666 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.2666 Scrap (S Group). A byproduct of unstemmed and stemmed tobacco. Scrap...

7 CFR 29.2441 - Scrap (S Group).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Scrap (S Group). 29.2441 Section 29.2441 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.2441 Scrap (S Group). A byproduct of unstemmed and stemmed tobacco. Scrap...

Recycling scheme for scrapped automobiles in Japan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suzuki, Masao; Nakajima, Akira; Taya, Sadao

Over 5 million cars are scrapped yearly in Japan. After dismantling scrapped automobiles, they are put into a shredder for differential recovery of ferrous and nonferrous metals. The residue, which is called shredder dust, runs over 1.2 million tons per year. This paper reports a entire sequence of scrapping cars in Japan with the following sections: (1) production and scrapped car management, (2) material composition, (3) dismantling, (4) shredder plant, (5) differential recovery of metals including specific gravity and newly developed color separation.

Scrap car recycling in Taiwan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, C.H.; Tai, H.S.; Fan, R.K.S.

1997-12-31

The official figure of registered automobiles released by the Ministry of Transportation of Taiwan, R.O.C. as of the end of April 1996, is approximately 4.8 millions. Among them, 18% of the cars are between seven and ten years old and 15% of the cars are old than ten years. The result of this large number of old cars is the problem of abandoned cars on the street of Taiwan. This phenomena not only hinders traffic flow but also undermines the living quality in the cities. To minimize these negative effects, EPA has promulgated a Scrap Motor Vehicles Management Regulation tomore » enforce the scrap car recycling in Taiwan. Under this regulation, a buyer of a new vehicle has to pay the Scrap Motor Vehicle Disposal fee (NT$ 3000, or US$ 110 for a car; and NT$ 700, or US$ 25 for a motorcycle). This paper presents the current status of scrap car recycling in Taiwan.« less

Surface debris inventory at White Wing Scrap Yard, Oak Ridge Reservation, Oak Ridge, Tennessee. Environmental Restoration Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez, R.E.; Tiner, P.F.; Williams, J.K.

1992-08-01

An inventory of surface debris in designated grid blocks at the White Wing Scrap Yard [Waste Area Grouping 11 (WAG 11)] was conducted intermittently from February through June 1992 by members of the Measurement Applications and Development Group, Health and Safety Research Division, Oak Ridge National Laboratory (ORNL) at the request of ORNL Environmental Restoration (ER) Program personnel. The objectives of this project are outlined in the following four phases: (1) estimate the amount (volume) and type (e.g., glass, metal and plastics) of surface waste material in 30 designated grid blocks (100- by 100-ft grids); (2) conduct limited air samplingmore » for organic chemical pollutants at selected locations (e.g., near drums, in holes, or other potentially contaminated areas); (3) conduct a walkover gamma radiation scan extending outward (approximately 50 ft) beyond the proposed location of the WAG 11 perimeter fence; and (4) recommend one grid block as a waste staging area. This recommendation is based on location and accessibility for debris staging/transport activities and on low levels of gamma radiation in the grid block.« less

Evaluation of Fine Aggregate Morphology by Image Method and Its Effect on Skid-Resistance of Micro-Surfacing.

PubMed

Xiao, Yue; Wang, Feng; Cui, Peide; Lei, Lei; Lin, Juntao; Yi, Mingwei

2018-05-29

Micro-surfacing is a widely used pavement preventive maintenance technology used all over the world, due to its advantages of fast construction, low maintenance cost, good waterproofness, and skid-resistance performance. This study evaluated the fine aggregate morphology and surface texture of micro-surfacing by AIMS (aggregate image measurement system), and explored the effect of aggregate morphology on skid-resistance of single-grade micro-surfacing. Sand patch test and British pendulum test were also used to detect skid-resistance for comparison with the image-based method. Wet abrasion test was used to measure skid-resistance durability for feasibility verification of single-grade micro-surfacing. The results show that the effect of Form2D on the skid-resistance of micro-surfacing is much stronger than that of angularity. Combining the feasibility analysis of durability and skid-resistance, 1.18⁻2.36 grade micro-surfacing meets the requirements of durability and skid-resistance at the same time. This study also determined that, compared with British pendulum test, the texture result obtained by sand patch test fits better with results of image method.

Evaluation of skid inventory data for development of trends : pilot study : final report.

DOT National Transportation Integrated Search

1983-12-01

This study examined historical data of the skid resistance inventory in Louisiana from 1974 through 1981 to determine trends. The data showed that no trend exists when using number of vehicle passes versus skid number difference on any surface presen...

Evaluation of the new Virginia Dept. of Highways and Transportation skid testing trailer.

DOT National Transportation Integrated Search

1975-01-01

The purpose of this study was to evaluate the new skid trailer obtained by the Virginia Department of Highways & Transportation and to determine how the survey skid testing program should be conducted in light of the findings. Specifically, those thi...

Vertical Drop Testing and Analysis of the Wasp Helicopter Skid Gear

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Fuchs, Yvonne T.

2007-01-01

This report describes an experimental program to assess the impact performance of a skid gear for use on the Wasp kit-built helicopter, which is marketed by HeloWerks, Inc. of Hampton, Virginia. In total, five vertical drop tests were performed. The test article consisted of a skid gear mounted beneath a steel plate. A seating platform was attached to the upper surface of the steel plate, and two 95th percentile Hybrid III male Anthropomorphic Test Devices (ATDs) were seated on the platform and secured using a four-point restraint system. The test article also included ballast weights to ensure the correct position of the Center-of-Gravity (CG). Twenty-six channels of acceleration data were collected per test at 50,000 samples per second. The five drop tests were conducted on two different gear configurations. The details of these test programs are presented, as well as an occupant injury assessment. Finally, a finite element model of the skid gear test article was developed for execution in LS-DYNA, an explicit nonlinear transient dynamic code, for predicting the skid gear and occupant dynamic responses due to impact.

Characterization of shredded television scrap and implications for materials recovery.

PubMed

Cui, Jirang; Forssberg, Eric

2007-01-01

Characterization of TV scrap was carried out by using a variety of methods, such as chemical analysis, particle size and shape analysis, liberation degree analysis, thermogravimetric analysis, sink-float test, and IR spectrometry. A comparison of TV scrap, personal computer scrap, and printed circuit board scrap shows that the content of non-ferrous metals and precious metals in TV scrap is much lower than that in personal computer scrap or printed circuit board scrap. It is expected that recycling of TV scrap will not be cost-effective by utilizing conventional manual disassembly. The result of particle shape analysis indicates that the non-ferrous metal particles in TV scrap formed as a variety of shapes; it is much more heterogeneous than that of plastics and printed circuit boards. Furthermore, the separability of TV scrap using density-based techniques was evaluated by the sink-float test. The result demonstrates that a high recovery of copper could be obtained by using an effective gravity separation process. Identification of plastics shows that the major plastic in TV scrap is high impact polystyrene. Gravity separation of plastics may encounter some challenges in separation of plastics from TV scrap because of specific density variations.

New findings regarding the significance of pavement skid resistance for road safety on Swiss freeways.

PubMed

Lindenmann, H P

2006-01-01

The significance of the influence of poor pavement skid resistance values on accident frequency in wet pavement conditions has been the object of many studies over several years. The various investigations have produced very diverse findings. Only seldom, however, has detailed consideration been given to the central question of whether pavement skid resistance is a decisive parameter in the occurrence of local accident "black spots." Until now, the focus has been more on describing a relationship between pavement skid resistance and accident frequency. In the course of the network-wide survey of the states of pavements and of accident occurrence on Switzerland's freeways from 1999 to 2003, it emerged that a relationship with inadequate pavement skid resistance was provable for only a small proportion of accident black spots. These findings were used to frame a guideline for authorities and highway operators about how to treat skid resistance when assessing pavements and accident occurrence on freeways.

Analysis and experimental kinematics of a skid-steering wheeled robot based on a laser scanner sensor.

PubMed

Wang, Tianmiao; Wu, Yao; Liang, Jianhong; Han, Chenhao; Chen, Jiao; Zhao, Qiteng

2015-04-24

Skid-steering mobile robots are widely used because of their simple mechanism and robustness. However, due to the complex wheel-ground interactions and the kinematic constraints, it is a challenge to understand the kinematics and dynamics of such a robotic platform. In this paper, we develop an analysis and experimental kinematic scheme for a skid-steering wheeled vehicle based-on a laser scanner sensor. The kinematics model is established based on the boundedness of the instantaneous centers of rotation (ICR) of treads on the 2D motion plane. The kinematic parameters (the ICR coefficient , the path curvature variable and robot speed ), including the effect of vehicle dynamics, are introduced to describe the kinematics model. Then, an exact but costly dynamic model is used and the simulation of this model's stationary response for the vehicle shows a qualitative relationship for the specified parameters and . Moreover, the parameters of the kinematic model are determined based-on a laser scanner localization experimental analysis method with a skid-steering robotic platform, Pioneer P3-AT. The relationship between the ICR coefficient and two physical factors is studied, i.e., the radius of the path curvature and the robot speed . An empirical function-based relationship between the ICR coefficient of the robot and the path parameters is derived. To validate the obtained results, it is empirically demonstrated that the proposed kinematics model significantly improves the dead-reckoning performance of this skid-steering robot.

ETF Facility evaporator skid orifice sizing design analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

ELLINGSON, S.D.

1999-08-31

This document releases and records the design analysis for sizing the Orifice plate being installed on the Effluent Treatment Facility (ETF) evaporator skid per Engineering Change Notice (ECN) 651583.

Design of bituminous mixes with high skid resistance.

DOT National Transportation Integrated Search

1979-01-01

Certain highway locations need exceptionally high skid resistance because of the alignment, geometry, and drainage of the roadway and the complex turning maneuvers required. Several beam specimens made of bituminous mixes incorporating unconventional...

7 CFR 29.1029 - Leaf scrap.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Leaf scrap. 29.1029 Section 29.1029 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1029 Leaf scrap. A byproduct of stemmed and unstemmed tobacco. [42 FR 21092, Apr. 25...

7 CFR 29.1029 - Leaf scrap.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Leaf scrap. 29.1029 Section 29.1029 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1029 Leaf scrap. A byproduct of stemmed and unstemmed tobacco. [42 FR 21092, Apr. 25...

7 CFR 29.1029 - Leaf scrap.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Leaf scrap. 29.1029 Section 29.1029 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1029 Leaf scrap. A byproduct of stemmed and unstemmed tobacco. [42 FR 21092, Apr. 25...

7 CFR 29.1029 - Leaf scrap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.1029 Section 29.1029 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1029 Leaf scrap. A byproduct of stemmed and unstemmed tobacco. [42 FR 21092, Apr. 25...

7 CFR 29.1029 - Leaf scrap.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Leaf scrap. 29.1029 Section 29.1029 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1029 Leaf scrap. A byproduct of stemmed and unstemmed tobacco. [42 FR 21092, Apr. 25...

Ground skidding and harvested stand attributes in Appalachian hardwood stands in West Virginia

Treesearch

Andrew F. Egan; John E. Baumgras

2003-01-01

A statewide logging-in-progress study was conducted in West Virginia to examine the associations among several ground skidding and harvested stand attributes. There was a strong positive association between skidding distance and cycle time, and a significant negative relationship between the percent of trees removed in the stand and total cycle time. The number of...

19 CFR 10.41a - Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of international...

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Lift vans, cargo vans, shipping tanks, skids... Traffic § 10.41a Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of international traffic; repair components. (a)(1) Lift vans, cargo vans, shipping tanks, skids, pallets, caul...

19 CFR 10.41a - Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of international...

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Lift vans, cargo vans, shipping tanks, skids... Traffic § 10.41a Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of international traffic; repair components. (a)(1) Lift vans, cargo vans, shipping tanks, skids, pallets, caul...

Virginia Department of Highways and Transportation skid testing equipment correlation results, 1974, 1975, and 1978.

DOT National Transportation Integrated Search

1978-01-01

The purpose of this study was to modify, as required, the previously established relationships between the VHTRC skid trailer, the VHTRC stopping distance car, and the first VDHT skid trailer, and to develop appropriate relationships with the above t...

Management options for recycling radioactive scrap metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dehmel, J.C.; MacKinney, J.; Bartlett, J.

1997-02-01

The feasibility and advantages of recycling radioactive scrap metals (RSM) have yet to be assessed, given the unique technical, regulatory, safety, and cost-benefit issues that have already been raised by a concerned recycling industry. As is known, this industry has been repeatedly involved with the accidental recycling of radioactive sources and, in some cases, with costly consequences. If recycling were deemed to be a viable option, it might have to be implemented with regulatory monitoring and controls. Its implementation may have to consider various and complex issues and address the requirements and concerns of distinctly different industries. There are threemore » basic options for the recycling of such scraps. They are: (1) recycling through the existing network of metal-scrap dealers and brokers, (2) recycling directly and only with specific steelmills, or (3) recycling through regional processing centers. Under the first option, scrap dealers and brokers would receive material from RSM generators and determine at which steelmills such scraps would be recycled. For the second option, RSM generators would deal directly with selected steelmills under specific agreements. For the third option, generators would ship scraps only to regional centers for processing and shipment to participating steelmills. This paper addresses the potential advantages of each option, identifies the types of arrangements that would need to be secured among all parties, and attempts to assess the receptivity of the recycling industry to each option.« less

Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biganzoli, Laura, E-mail: laura.biganzoli@mail.polimi.it; Gorla, Leopoldo; Nessi, Simone

Highlights: Black-Right-Pointing-Pointer Aluminium packaging partitioning in MSW incineration residues is evaluated. Black-Right-Pointing-Pointer The amount of aluminium packaging recoverable from the bottom ashes is evaluated. Black-Right-Pointing-Pointer Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. Black-Right-Pointing-Pointer 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determinemore » a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.« less

Comparisons of four categories of waste recycling in China's paper industry based on physical input-output life-cycle assessment model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang Sai; Zhang, Tianzhu, E-mail: zhangtz@mail.tsinghua.edu.cn; Xu Yijian

Highlights: Black-Right-Pointing-Pointer Using crop straws and wood wastes for paper production should be promoted. Black-Right-Pointing-Pointer Bagasse and textile waste recycling should be properly limited. Black-Right-Pointing-Pointer Imports of scrap paper should be encouraged. Black-Right-Pointing-Pointer Sensitivity analysis, uncertainties and policy implications are discussed. - Abstract: Waste recycling for paper production is an important component of waste management. This study constructs a physical input-output life-cycle assessment (PIO-LCA) model. The PIO-LCA model is used to investigate environmental impacts of four categories of waste recycling in China's paper industry: crop straws, bagasse, textile wastes and scrap paper. Crop straw recycling and wood utilization for papermore » production have small total intensity of environmental impacts. Moreover, environmental impacts reduction of crop straw recycling and wood utilization benefits the most from technology development. Thus, using crop straws and wood (including wood wastes) for paper production should be promoted. Technology development has small effects on environmental impacts reduction of bagasse recycling, textile waste recycling and scrap paper recycling. In addition, bagasse recycling and textile waste recycling have big total intensity of environmental impacts. Thus, the development of bagasse recycling and textile waste recycling should be properly limited. Other pathways for reusing bagasse and textile wastes should be explored and evaluated. Moreover, imports of scrap paper should be encouraged to reduce large indirect impacts of scrap paper recycling on domestic environment.« less

Highway pavement performance test for colored thin anti-skidding layers

NASA Astrophysics Data System (ADS)

Gao, Wei; Cui, Wei; Xu, Ming

2018-03-01

Based on the actual service condition of highway pavement colored thin anti-skidding layers, with materials of color quartz sand and two-component acrylic resin as basis, we designed such tests as the bond strength, shearing strength, tear strength, fatigue performance and aggregate polished value, and included the freeze-thaw cycle and de-icing salt and other factors in the experiment, connecting with the climate characteristics of circumpolar latitude and low altitude in Heilongjiang province. Through the pavement performance test, it is confirmed that the colored thin anti-skidding layers can adapt to cold and humid climate conditions, and its physical mechanical properties are good.

48 CFR 45.606-1 - Contractor with an approved scrap procedure.

Code of Federal Regulations, 2011 CFR

2011-10-01

... production or testing under this contract without Government approval. However, if the scrap requires... schedule. (b) For scrap from other than production or testing, the contractor may prepare scrap lists in..., flight safety critical aircraft parts, and scrap that— (1) Requires demilitarization; (2) Is a classified...

48 CFR 45.606-1 - Contractor with an approved scrap procedure.

Code of Federal Regulations, 2010 CFR

2010-10-01

... production or testing under this contract without Government approval. However, if the scrap requires... schedule. (b) For scrap from other than production or testing, the contractor may prepare scrap lists in..., flight safety critical aircraft parts, and scrap that— (1) Requires demilitarization; (2) Is a classified...

E-Waste and the Sustainable Organisation: Griffith University's Approach to E-Waste

ERIC Educational Resources Information Center

Davis, Georgina; Wolski, Malcolm

2009-01-01

Purpose: This paper seeks to provide details of Griffith University's (GU) approach for sustainably dealing with electronic waste (e-waste) and the benefits of using the e-waste programme as a valuable educational case study for ESD. Design/methodology/approach: The e-waste programme is explained with reference to key resources and literature, so…

Comparisons of four categories of waste recycling in China's paper industry based on physical input-output life-cycle assessment model.

PubMed

Liang, Sai; Zhang, Tianzhu; Xu, Yijian

2012-03-01

Waste recycling for paper production is an important component of waste management. This study constructs a physical input-output life-cycle assessment (PIO-LCA) model. The PIO-LCA model is used to investigate environmental impacts of four categories of waste recycling in China's paper industry: crop straws, bagasse, textile wastes and scrap paper. Crop straw recycling and wood utilization for paper production have small total intensity of environmental impacts. Moreover, environmental impacts reduction of crop straw recycling and wood utilization benefits the most from technology development. Thus, using crop straws and wood (including wood wastes) for paper production should be promoted. Technology development has small effects on environmental impacts reduction of bagasse recycling, textile waste recycling and scrap paper recycling. In addition, bagasse recycling and textile waste recycling have big total intensity of environmental impacts. Thus, the development of bagasse recycling and textile waste recycling should be properly limited. Other pathways for reusing bagasse and textile wastes should be explored and evaluated. Moreover, imports of scrap paper should be encouraged to reduce large indirect impacts of scrap paper recycling on domestic environment. Copyright © 2011 Elsevier Ltd. All rights reserved.

Cost-assessment Analysis of Local Vehicle Scrapping Facility

NASA Astrophysics Data System (ADS)

Grabowski, Lukasz; Gliniak, Maciej; Polek, Daria; Gruca, Maria

2017-12-01

The purpose of the paper was to analyse the costs of recycling vehicles at local vehicle scrapping facility. The article contains regulations concerning vehicle decommissioning, describes the types of recovery, vehicles recycling networks, analyses the structure of a disassembly station, as well as the financial and institutional system in charge of dealing with the recycling of vehicles in Poland. The authors present the number of scrapped vehicles at local recycling company and the level of achieved recovery and recycling. The research presented in the article shows financial situation of the vehicle scrapping industry. In addition, it has been observed that the number of subsidies are directly proportional to the number of scrapped vehicles, and achieved levels of recycling and recovery depends on the percentage of incomplete vehicles.

46 CFR 148.265 - Fish meal or fish scrap.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Fish meal or fish scrap. 148.265 Section 148.265... MATERIALS THAT REQUIRE SPECIAL HANDLING Special Requirements for Certain Materials § 148.265 Fish meal or fish scrap. (a) This part does not apply to fish meal or fish scrap that contains less than 5 percent...

46 CFR 148.265 - Fish meal or fish scrap.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Fish meal or fish scrap. 148.265 Section 148.265... MATERIALS THAT REQUIRE SPECIAL HANDLING Special Requirements for Certain Materials § 148.265 Fish meal or fish scrap. (a) This part does not apply to fish meal or fish scrap that contains less than 5 percent...

46 CFR 148.265 - Fish meal or fish scrap.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Fish meal or fish scrap. 148.265 Section 148.265... MATERIALS THAT REQUIRE SPECIAL HANDLING Special Requirements for Certain Materials § 148.265 Fish meal or fish scrap. (a) This part does not apply to fish meal or fish scrap that contains less than 5 percent...

7 CFR 29.2441 - Scrap (S Group).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Scrap (S Group). 29.2441 Section 29.2441 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... the web portions of tobacco leaves reduced to scrap by any process. summary of standard grades ...

7 CFR 29.6131 - Scrap (S Group).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Scrap (S Group). 29.6131 Section 29.6131 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing..., or the web portion of tobacco leaves reduced to scrap by any process. Summary of Standard Grades ...

49 CFR 173.218 - Fish meal or fish scrap.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Fish meal or fish scrap. 173.218 Section 173.218... Fish meal or fish scrap. (a) Except as provided in Column (7) of the HMT in § 172.101 of this subchapter, fish meal or fish scrap, containing at least 6%, but not more than 12% water, is authorized for...

49 CFR 173.218 - Fish meal or fish scrap.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Fish meal or fish scrap. 173.218 Section 173.218... Fish meal or fish scrap. (a) Except as provided in Column (7) of the HMT in § 172.101 of this subchapter, fish meal or fish scrap, containing at least 6%, but not more than 12% water, is authorized for...

49 CFR 173.218 - Fish meal or fish scrap.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 2 2013-10-01 2013-10-01 false Fish meal or fish scrap. 173.218 Section 173.218... Fish meal or fish scrap. (a) Except as provided in Column (7) of the HMT in § 172.101 of this subchapter, fish meal or fish scrap, containing at least 6%, but not more than 12% water, is authorized for...

49 CFR 173.218 - Fish meal or fish scrap.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 2 2014-10-01 2014-10-01 false Fish meal or fish scrap. 173.218 Section 173.218... Fish meal or fish scrap. (a) Except as provided in Column (7) of the HMT in § 172.101 of this subchapter, fish meal or fish scrap, containing at least 6%, but not more than 12% water, is authorized for...

49 CFR 173.218 - Fish meal or fish scrap.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 2 2012-10-01 2012-10-01 false Fish meal or fish scrap. 173.218 Section 173.218... Fish meal or fish scrap. (a) Except as provided in Column (7) of the HMT in § 172.101 of this subchapter, fish meal or fish scrap, containing at least 6%, but not more than 12% water, is authorized for...

Design of bituminous surface mixes with high skid resistance.

DOT National Transportation Integrated Search

1974-01-01

The Virginia Highway Research Council has proposed a study of the skid resistance of bituminous surfaces incorporating relatively hard and expensive aggregates. The hardness of the aggregates to be used aluminum oxide (Exolon) and calcined kaolin -- ...

The steel scrap age.

PubMed

Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

2013-04-02

Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

["Scrap" as an element of communication in nursing].

PubMed

Esperidião, E; Medeiros Teixeira, M E; Rodrigues Stacciarini, J M

1996-04-01

Based on the understanding that students and nursing professionals demonstrate difficulties in being a "person" in the profession, we developed a descriptive and exploratory study with a qualitative approach. Then, we offered during the "Iind" II Nursing Congress in the city of Goiania a work-shop called "LEARNING ABOUT NURSE'S ENTITY". Among various processes of work-groups; the "Scrap" was used as a kind of communication. It was a resource utilized in certain dynamics, being the object of our study that has the following goals: to identify the representation of nurse's "entity", to verify the interaction process "man-scrap" during the realization of the work and to verify if the object is represented as it really is. We have seen that there are particularities in the representation of nurse's entity. Regarding "man-scrap" interaction it had the followed sequence: finding strange the material and the proposal of work, manipulating and identifying objects, "scrap" selection and concretion of the job. With respect to the objects, we perceived a clear preference to the ones related to the profession. Finally, we suggest that other studies about the "scrap" communication element, must be developed.

Development of an electric, battery powered, skid-steer loader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alcock, R.; Froehlich, D.P.; Christianson, L.L.

1985-01-01

A battery powered, skid-steer loader was developed for farm chore routines and materials handling activities. Outlined are details on drive train, hydraulics, loader, frame, cab, controls, battery and controller. Preliminary performance characteristics of the hydraulics are presented.

Minnesota's experience with scrap shingles in bituminous pavements

DOT National Transportation Integrated Search

1996-10-01

The Minnesota Department of Transportation (Mn/DOT) has experimented with the use of shingle scrap in hot mix asphalt (HMA) since 1990. To date, the source of the shingle scrap has been shingle manufacturers exclusively. The manufactured shingle scra...

Projectile Roll Dynamics and Control With a Low-Cost Skid-to-Turn Maneuver System

DTIC Science & Technology

2013-03-01

scheme. The mechatronics of the maneuver system was provided. The suitability of this design for survival at gun launch was assessed through...Projectile Roll Dynamics and Control With a Low-Cost Skid-to-Turn Maneuver System by Frank Fresconi, Ilmars Celmins, Mark Ilg, and James...5069 ARL-TR-6363 March 2013 Projectile Roll Dynamics and Control With a Low-Cost Skid-to-Turn Maneuver System Frank Fresconi, Ilmars

Non-contact skid resistance measurement : final report, December 2009.

DOT National Transportation Integrated Search

2009-12-01

In this research, a correlation between the SN40R collected by locked wheel skid tester and the : texture data or Mean Profile Depth (MPD) collected by a vehicle mounted laser operating at highway : speeds was developed. The proposed correlation betw...

Comparison of skid resistance testing to stopping distance testing.

DOT National Transportation Integrated Search

1998-01-01

This report is intended to statistically summarize the results of a side-by-side test of the skid resistance testing trailer utilized by the Oregon Department of Transportation (ODOT), and the stopping distance car utilized by the Oregon State Police...

Annual waste reduction activities report. Issue 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1991-03-18

This report discusses the waste minimization activities for the Pinellas Plant. The Pinellas Plant deals with low-level radioactive wastes, solvents, scrap metals and various other hazardous materials. This program has realized cost savings through recycling and reuse of materials.

Skid Prevention for EVs Based on the Emulation of Torque Reduction Characteristics of Separately-excited DC Motor

NASA Astrophysics Data System (ADS)

Kodama, Shinya; Hori, Yoichi

It is well-known that the separately-excited DC motor has effective torque (current) reduction characteristics in response to rapid increase in the rotational speed of the motor. These characteristics have been utilized in adhesion control of electric railway trains with separately-excited DC motor. Up to now, we have proposed a new skid prevention method for EVs, utilizing these characteristics and have made experiments with the hardware skid simulator “Motor-Generator setup”. In this paper, we applied this skid prevention control to our new vehicle “UOT CADWELL EV" equipped with BLDC motors and showed its effectiveness.

Results of chemical decontamination of DOE`s uranium-enrichment scrap metal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levesque, R.G.

1997-02-01

The CORPEX{reg_sign} Nuclear Decontamination Processes were used to decontaminate representative scrap metal specimens obtained from the existing scrap metal piles located at the Department of Energy (DOE) Portsmouth Gaseous Diffusion Plant (PORTS), Piketon, Ohio. In September 1995, under contract to Lockheed Martin Energy Systems, MELE Associates, Inc. performed the on-site decontamination demonstration. The decontamination demonstration proved that significant amounts of the existing DOE scrap metal can be decontaminated to levels where the scrap metal could be economically released by DOE for beneficial reuse. This simple and environmentally friendly process can be used as an alternative, or in addition to, smeltingmore » radiologically contaminated scrap metal.« less

Bioleaching of electronic scrap by mixed culture of moderately thermophilic microorganisms

NASA Astrophysics Data System (ADS)

Ivǎnuş, D.; ǎnuş, R. C., IV; Cǎlmuc, F.

2010-06-01

A process for the metal recovery from electronic scrap using bacterial leaching was investigated. A mixed culture of moderately thermophilic microorganisms was enriched from acid mine drainages (AMDs) samples collected from several sulphide mines in Romania, and the bioleaching of electronic scrap was conducted both in shake flask and bioreactor. The results show that in the shake flask, the mixture can tolerate 50 g/L scrap after being acclimated to gradually increased concentrations of scrap. The copper extraction increases obviously in bioleaching of scrap with moderately thermophilic microorganisms supplemented with 0.4 g/L yeast extract at 180 r/min, 74% copper can be extracted in the pulp of 50 g/L scrap after 20 d. Compared with copper extractions of mesophilic culture, unacclimated culture and acclimated culture without addition of yeast extract, that of accliniated culture with addition of yeast extract is increased by 53%, 44% and 16%, respectively. In a completely stirred tank reactor, the mass fraction of copper and total iron extraction reach up to 81% and 56%, respectively. The results also indicate that it is necessary to add a large amount of acid to the pulp to extract copper from electronic scrap effectively.

Evaluation of drilled-ball bearings at DN values to three million. 2: Experimental skid study and endurance tests

NASA Technical Reports Server (NTRS)

Holmes, P. W.

1972-01-01

Both drilled-and solid-ball 120-mm-bore bearings were tested at speeds up to 24,000 rpm to determine skid characteristics. The thrust loads were varied from 5000 lb down to 370 lb. No gross skidding occurred, and the behavior of the two bearing types was generally similar; however, two drilled-ball bearing failures occurred during the skid tests. In the endurance tests, 25 cycles of start, run (for one hour), and stop were completed before a drilled-ball bearing failed. In all three cases, the ball had failed in flexure fatigue.

Scrap tyre recycling process with molten zinc as direct heat transfer and solids separation fluid: A new reactor concept.

PubMed

Riedewald, Frank; Goode, Kieran; Sexton, Aidan; Sousa-Gallagher, Maria J

2016-01-01

Every year about 1.5 billion tyres are discarded worldwide representing a large amount of solid waste, but also a largely untapped source of raw materials. The objective of the method was to prove the concept of a novel scrap tyre recycling process which uses molten zinc as the direct heat transfer fluid and, simultaneously, uses this media to separate the solids products (i.e. steel and rCB) in a sink-float separation at an operating temperature of 450-470 °C. This methodology involved: •construction of the laboratory scale batch reactor,•separation of floating rCB from the zinc,•recovery of the steel from the bottom of the reactor following pyrolysis.

A note on scrap in the 1992 U.S. input-output tables

USGS Publications Warehouse

Swisko, George M.

2000-01-01

Introduction A key concern of industrial ecology and life cycle analysis is the disposal and recycling of scrap. One might conclude that the U.S. input-output tables are appropriate tools for analyzing scrap flows. Duchin, for instance, has suggested using input-output analysis for industrial ecology, indicating that input-output economics can trace the stocks and flows of energy and other materials from extraction through production and consumption to recycling or disposal. Lave and others use input-output tables to design life cycle assessment models for studying product design, materials use, and recycling strategies, even with the knowledge that these tables suffer from a lack of comprehensive and detailed data that may never be resolved. Although input-output tables can offer general guidance about the interdependence of economic and environmental processes, data reporting by industry and the economic concepts underlying these tables pose problems for rigorous material flow examinations. This is especially true for analyzing the output of scrap and scrap flows in the United States and estimating the amount of scrap that can be recycled. To show how data reporting has affected the values of scrap in recent input-output tables, this paper focuses on metal scrap generated in manufacturing. The paper also briefly discusses scrap that is not included in the input-output tables and some economic concepts that limit the analysis of scrap flows.

Zero valent iron significantly enhances methane production from waste activated sludge by improving biochemical methane potential rather than hydrolysis rate.

PubMed

Liu, Yiwen; Wang, Qilin; Zhang, Yaobin; Ni, Bing-Jie

2015-02-05

Anaerobic digestion has been widely applied for waste activated sludge (WAS) treatment. However, methane production from anaerobic digestion of WAS is usually limited by the slow hydrolysis rate and/or poor biochemical methane potential of WAS. This work systematically studied the effects of three different types of zero valent iron (i.e., iron powder, clean scrap and rusty scrap) on methane production from WAS in anaerobic digestion, by using both experimental and mathematical approaches. The results demonstrated that both the clean and the rusty iron scrap were more effective than the iron powder for improving methane production from WAS. Model-based analysis showed that ZVI addition significantly enhanced methane production from WAS through improving the biochemical methane potential of WAS rather than its hydrolysis rate. Economic analysis indicated that the ZVI-based technology for enhancing methane production from WAS is economically attractive, particularly considering that iron scrap can be freely acquired from industrial waste. Based on these results, the ZVI-based anaerobic digestion process of this work could be easily integrated with the conventional chemical phosphorus removal process in wastewater treatment plant to form a cost-effective and environment-friendly approach, enabling maximum resource recovery/reuse while achieving enhanced methane production in wastewater treatment system.

Zero Valent Iron Significantly Enhances Methane Production from Waste Activated Sludge by Improving Biochemical Methane Potential Rather Than Hydrolysis Rate

PubMed Central

Liu, Yiwen; Wang, Qilin; Zhang, Yaobin; Ni, Bing-Jie

2015-01-01

Anaerobic digestion has been widely applied for waste activated sludge (WAS) treatment. However, methane production from anaerobic digestion of WAS is usually limited by the slow hydrolysis rate and/or poor biochemical methane potential of WAS. This work systematically studied the effects of three different types of zero valent iron (i.e., iron powder, clean scrap and rusty scrap) on methane production from WAS in anaerobic digestion, by using both experimental and mathematical approaches. The results demonstrated that both the clean and the rusty iron scrap were more effective than the iron powder for improving methane production from WAS. Model-based analysis showed that ZVI addition significantly enhanced methane production from WAS through improving the biochemical methane potential of WAS rather than its hydrolysis rate. Economic analysis indicated that the ZVI-based technology for enhancing methane production from WAS is economically attractive, particularly considering that iron scrap can be freely acquired from industrial waste. Based on these results, the ZVI-based anaerobic digestion process of this work could be easily integrated with the conventional chemical phosphorus removal process in wastewater treatment plant to form a cost-effective and environment-friendly approach, enabling maximum resource recovery/reuse while achieving enhanced methane production in wastewater treatment system. PMID:25652244

Zero Valent Iron Significantly Enhances Methane Production from Waste Activated Sludge by Improving Biochemical Methane Potential Rather Than Hydrolysis Rate

NASA Astrophysics Data System (ADS)

Liu, Yiwen; Wang, Qilin; Zhang, Yaobin; Ni, Bing-Jie

2015-02-01

Anaerobic digestion has been widely applied for waste activated sludge (WAS) treatment. However, methane production from anaerobic digestion of WAS is usually limited by the slow hydrolysis rate and/or poor biochemical methane potential of WAS. This work systematically studied the effects of three different types of zero valent iron (i.e., iron powder, clean scrap and rusty scrap) on methane production from WAS in anaerobic digestion, by using both experimental and mathematical approaches. The results demonstrated that both the clean and the rusty iron scrap were more effective than the iron powder for improving methane production from WAS. Model-based analysis showed that ZVI addition significantly enhanced methane production from WAS through improving the biochemical methane potential of WAS rather than its hydrolysis rate. Economic analysis indicated that the ZVI-based technology for enhancing methane production from WAS is economically attractive, particularly considering that iron scrap can be freely acquired from industrial waste. Based on these results, the ZVI-based anaerobic digestion process of this work could be easily integrated with the conventional chemical phosphorus removal process in wastewater treatment plant to form a cost-effective and environment-friendly approach, enabling maximum resource recovery/reuse while achieving enhanced methane production in wastewater treatment system.

E-waste: a global hazard.

PubMed

Perkins, Devin N; Brune Drisse, Marie-Noel; Nxele, Tapiwa; Sly, Peter D

2014-01-01

Waste from end-of-life electrical and electronic equipment, known as e-waste, is a rapidly growing global problem. E-waste contains valuable materials that have an economic value when recycled. Unfortunately, the majority of e-waste is recycled in the unregulated informal sector and results in significant risk for toxic exposures to the recyclers, who are frequently women and children. The aim of this study was to document the extent of the problems associated with inappropriate e-waste recycling practices. This was a narrative review that highlighted where e-waste is generated, where it is recycled, the range of adverse environmental exposures, the range of adverse health consequences, and the policy frameworks that are intended to protect vulnerable populations from inappropriate e-waste recycling practices. The amount of e-waste being generated is increasing rapidly and is compounded by both illegal exportation and inappropriate donation of electronic equipment, especially computers, from developed to developing countries. As little as 25% of e-waste is recycled in formal recycling centers with adequate worker protection. The health consequences of both direct exposures during recycling and indirect exposures through environmental contamination are potentially severe but poorly studied. Policy frameworks aimed at protecting vulnerable populations exist but are not effectively applied. E-waste recycling is necessary but it should be conducted in a safe and standardized manor. The acceptable risk thresholds for hazardous, secondary e-waste substances should not be different for developing and developed countries. However, the acceptable thresholds should be different for children and adults given the physical differences and pronounced vulnerabilities of children. Improving occupational conditions for all e-waste workers and striving for the eradication of child labor is non-negotiable. Crown Copyright © 2014. Published by Elsevier Inc. All rights reserved.

Combined removal of a BTEX, TCE, and cis-DCE mixture using Pseudomonas sp. immobilized on scrap tyres.

PubMed

Lu, Qihong; de Toledo, Renata Alves; Xie, Fei; Li, Junhui; Shim, Hojae

2015-09-01

The simultaneous aerobic removal of a mixture of benzene, toluene, ethylbenzene, and o,m,p-xylene (BTEX); cis-dichloroethylene (cis-DCE); and trichloroethylene (TCE) from the artificially contaminated water using an indigenous bacterial isolate identified as Pseudomonas plecoglossicida immobilized on waste scrap tyres was investigated. Suspended and immobilized conditions were compared for the removal of these volatile organic compounds. For the immobilized system, toluene, benzene, and ethylbenzene were completely removed, while the highest removal efficiencies of 99.0 ± 0.1, 96.8 ± 0.3, 73.6 ± 2.5, and 61.6 ± 0.9% were obtained for o-xylene, m,p-xylene, TCE, and cis-DCE, respectively. The sorption kinetics of contaminants towards tyre surface was also evaluated, and the sorption capacity generally followed the order of toluene > benzene > m,p-xylene > o-xylene > ethylbenzene > TCE > cis-DCE. Scrap tyres showed a good capability for the simultaneous sorption and bioremoval of BTEX/cis-DCE/TCE mixture, implying a promising waste material for the removal of contaminant mixture from industrial wastewater or contaminated groundwater.

Slip-based terrain estimation with a skid-steer vehicle

NASA Astrophysics Data System (ADS)

Reina, Giulio; Galati, Rocco

2016-10-01

In this paper, a novel approach for online terrain characterisation is presented using a skid-steer vehicle. In the context of this research, terrain characterisation refers to the estimation of physical parameters that affects the terrain ability to support vehicular motion. These parameters are inferred from the modelling of the kinematic and dynamic behaviour of a skid-steer vehicle that reveals the underlying relationships governing the vehicle-terrain interaction. The concept of slip track is introduced as a measure of the slippage experienced by the vehicle during turning motion. The proposed terrain estimation system includes common onboard sensors, that is, wheel encoders, electrical current sensors and yaw rate gyroscope. Using these components, the system can characterise terrain online during normal vehicle operations. Experimental results obtained from different surfaces are presented to validate the system in the field showing its effectiveness and potential benefits to implement adaptive driving assistance systems or to automatically update the parameters of onboard control and planning algorithms.

Finite horizon optimum control with and without a scrap value

NASA Astrophysics Data System (ADS)

Neck, R.; Blueschke-Nikolaeva, V.; Blueschke, D.

2017-06-01

In this paper, we study the effects of scrap values on the solutions of optimal control problems with finite time horizon. We show how to include a scrap value, either for the state variables or for the state and the control variables, in the OPTCON2 algorithm for the optimal control of dynamic economic systems. We ask whether the introduction of a scrap value can serve as a substitute for an infinite horizon in economic policy optimization problems where the latter option is not available. Using a simple numerical macroeconomic model, we demonstrate that the introduction of a scrap value cannot induce control policies which can be expected for problems with an infinite time horizon.

Full-Tree Skidding Favors Black Spruce Reproduction Under Certain Peatland Conditions

Treesearch

William F. Johnston

1980-01-01

Two trials on different sites indicate that clearcut black spruce reproduces well after full-tree skidding only on nonbrushy sites that have fairly abundant sphagnum seedbeds and adequate natural seeding.

Investigation of best options for using scrap tires in highway noise barriers.

DOT National Transportation Integrated Search

2011-06-01

In Colorado, approximately 60 million scrap tires have been stockpiled and approximately 4.5 million scrap tires are : generated annually. While CDOT does not generate these scrap tires, CDOT does have goals and policies to promote : sustainability/r...

An assessment of the skid resistance effect on traffic safety under wet-pavement conditions.

PubMed

Pardillo Mayora, José M; Jurado Piña, Rafael

2009-07-01

Pavement-tire friction provides the grip that is required for maintaining vehicle control and for stopping in emergency situations. Statistically significant negative correlations of skid resistance values and wet-pavement accident rates have been found in previous research. Skid resistance measured with SCRIM and crash data from over 1750km of two-lane rural roads in the Spanish National Road System were analyzed to determine the influence of pavement conditions on safety and to assess the effects of improving pavement friction on safety. Both wet- and dry-pavement crash rates presented a decreasing trend as skid resistance values increased. Thresholds in SCRIM coefficient values associated with significant decreases in wet-pavement crash rates were determined. Pavement friction improvement schemes were found to yield significant reductions in wet-pavement crash rates averaging 68%. The results confirm the importance of maintaining adequate levels of pavement friction to safeguard traffic safety as well as the potential of pavement friction improvement schemes to achieve significant crash reductions.

Highly efficient and selective leaching of silver from electronic scrap in the base-activated persulfate - ammonia system.

PubMed

Hyk, Wojciech; Kitka, Konrad

2017-02-01

A system composed of persulfate salt and ammonia in highly alkaline aqueous solution is developed and examined for leaching metallic silver from elements of the electronic waste materials (e-scrap). Strong base activates persulfate ions providing in situ generation of highly reactive oxygen molecules. The oxidized metal forms then well soluble complex ions with ammonia ligands. The kinetic studies of the leaching process were performed for pure metallic silver. They revealed that the efficiency of the process is affected by the type of the persulfate salt. By employing potassium persulfate one obtains significantly (more than 50% for silver plates and more than 100% for silver powder) increased efficiency of silver dissolution compared to the solution composed of either sodium or ammonium persulfates. In the range of persulfate concentrations between 0.02 and 0.23mol/L the apparent reaction order with respect to the persulfate concentration was similar for all persulfate salts and was estimated to be around 0.5. The room temperature (22±2°C) seems to be an optimal temperature for the leaching process. An increase in the temperature resulted in the significant drop in the silver dissolution rate due to the decreased solubility of oxygen. Based on these results a possible mechanism of dissolving silver is discussed and the optimal composition of the leaching solution is formulated. The obtained formulation of the leaching solution was applied for the extraction of silver coatings of Cu-based e-waste scrap and the obtained results revealed an important effect of copper in the mechanism of the leaching process. The regression analysis of the leaching curve indicated that each gram of base-activated potassium persulfate under the specified conditions may leach almost 100mg of silver coatings in a form of well soluble diamminesilver (I) complex. The silver complex can be relatively easy reduced to metallic silver. The method developed is relatively cheap, low toxic and

146. FUEL LINE TO SKID 2 (FUEL LOADER) IN FUEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

146. FUEL LINE TO SKID 2 (FUEL LOADER) IN FUEL CONTROL ROOM (215), LSB (BLDG. 751). LIQUID NITROGEN/HELIUM HEAT EXCHANGER ON RIGHT. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

United States copper metal and scrap use and trade patterns, 1995‒2014

USGS Publications Warehouse

Goonan, Thomas G.

2016-06-17

This report considers changes to the copper and copper scrap industries of the United States. For the study period, 1995 through 2014, U.S. refined copper production from all sources (primary and secondary materials) decreased from 2.28 million metric tons (Mt) of copper to 1.05 Mt (a 54 percent decrease). During the same period, U.S. copper scrap net exports increased from 0.203 Mt to 0.737 Mt (a 263 percent increase and a compound annual growth rate of about 7.0 percent per year). Copper and copper scrap prices (in constant 2014 dollars) rose such that 2014 prices were about 48 percent greater than 1995 prices. From 1995 through 2014, Chinese imports of copper scrap from the United States grew from 0.061 Mt to 0.569 Mt (an increase of about 830 percent and a compound annual growth rate of about 12.5 percent per year). In 2011, Chinese imports of U.S. copper scrap peaked at 0.745 Mt of contained copper. In 1995, Chinese imports of U.S. copper scrap accounted for 17 percent of U.S. copper scrap exports. By 2014, Chinese imports accounted for 69 percent of U.S. copper scrap exports (by weight), and Chinese imports of U.S. copper scrap were valued at $1.45 billion.

Analysis and Experimental Kinematics of a Skid-Steering Wheeled Robot Based on a Laser Scanner Sensor

PubMed Central

Wang, Tianmiao; Wu, Yao; Liang, Jianhong; Han, Chenhao; Chen, Jiao; Zhao, Qiteng

2015-01-01

Skid-steering mobile robots are widely used because of their simple mechanism and robustness. However, due to the complex wheel-ground interactions and the kinematic constraints, it is a challenge to understand the kinematics and dynamics of such a robotic platform. In this paper, we develop an analysis and experimental kinematic scheme for a skid-steering wheeled vehicle based-on a laser scanner sensor. The kinematics model is established based on the boundedness of the instantaneous centers of rotation (ICR) of treads on the 2D motion plane. The kinematic parameters (the ICR coefficient χ, the path curvature variable λ and robot speed v), including the effect of vehicle dynamics, are introduced to describe the kinematics model. Then, an exact but costly dynamic model is used and the simulation of this model’s stationary response for the vehicle shows a qualitative relationship for the specified parameters χ and λ. Moreover, the parameters of the kinematic model are determined based-on a laser scanner localization experimental analysis method with a skid-steering robotic platform, Pioneer P3-AT. The relationship between the ICR coefficient χ and two physical factors is studied, i.e., the radius of the path curvature λ and the robot speed v. An empirical function-based relationship between the ICR coefficient of the robot and the path parameters is derived. To validate the obtained results, it is empirically demonstrated that the proposed kinematics model significantly improves the dead-reckoning performance of this skid–steering robot. PMID:25919370

E-waste interventions in Ghana.

PubMed

Asante, Kwadwo Ansong; Pwamang, John A; Amoyaw-Osei, Yaw; Ampofo, Joseph Addo

2016-03-01

Electrical and electronic waste (e-waste) has become an emerging environmental and human health problem in the world in the 21st century. Recently, the developing nations of West Africa (e.g. Ghana and Nigeria) have become a major destination for e-waste worldwide. In Ghana, the e-waste recyclers use primitive methods (mechanical shredding and open burning) to remove plastic insulation from copper cables. This technique can release highly toxic chemicals and severely affect the environment and human health if improperly managed. It is as a result of the adverse impact on human health that some interventions are being made in Ghana to reduce exposure. The present mode of recycling/dismantling, which happens at Agbogbloshie must be replaced by official receiving/recycling centers to be established. Currently, equipment to strip both large and small cables are available in the country via the Blacksmith Institute (USA) and it is expected that the e-waste workers will embrace the use of these machines. This technology will go a long way to help prevent the burning of e-waste and will be replicated in other smaller e-waste centers in the country.

Sink-float ferrofluid separator applicable to full scale nonferrous scrap separation

NASA Technical Reports Server (NTRS)

1973-01-01

Design and performance of a ferrofluid levitation separator for recovering nonferrous metals from shredded automobiles are reported. The scrap separator uses an electromagnet to generate a region of constant density within a pool of ferrofluid held between the magnetic poles; a saturated kerosene base ferrofluid as able to float all common industrial metals of interest. Conveyors move the scrap into the ferrofluid for separation according to density. Results of scrap mixture separation studies establish the technical feasibility of relatively pure aluminum alloy and zinc alloy fractions from shredded automobile scrap by this ferrofluid levitation process. Economic projections indicate profitable operation for shredders handling more than 300 cars per day.

'Skidding' of the CRRES G-9 barium release

NASA Technical Reports Server (NTRS)

Huba, J. D.; Mitchell, H. G.; Fedder, J. A.; Bernhardt, P. A.

1992-01-01

A simulation study and experimental data of the CRRES G-9 ionospheric barium release are presented. The simulation study is based on a 2D electrostatic code that incorporates time-dependent coupling to the background plasma. It is shown that the densest portion of the barium ion cloud 'skids' about 15 km within the first three seconds following the release, consistent with the optical data analyses.

Recovery of Nickel from Nickel-Based Superalloy Scraps by Utilizing Molten Zinc

NASA Astrophysics Data System (ADS)

Yagi, Ryohei; Okabe, Toru H.

2017-02-01

With the purpose of developing a new process for recycling nickel (Ni) directly from superalloy scraps, a fundamental study on the extraction and separation of Ni was carried out using molten zinc (Zn) as the extraction medium. In order to examine the reaction between molten Zn and the Ni-based superalloy, superalloy samples and Zn shots were heated at 1173 K (900 °C) for 6 hours. After heating, the superalloy samples fully reacted with Zn and dissolved in molten Zn. The Zn-alloyed sample obtained by slow cooling consisted of two separated upper and lower phases. In the upper part of the sample, only Zn and the Zn-Ni alloys were found; in the lower part, an intermetallic alloy consisting of refractory metals such as rhenium (Re) and tantalum (Ta) was found. This result shows that Ni and refractory metals contained in the scrap can be separated by utilizing the density differences between the Zn-Ni alloy and the refractory metals in molten Zn. Vacuum treatment of the upper part of the Zn-alloyed sample at 1173 K (900 °C) reduced the concentration of Zn in the sample from 97.0 to 0.4 mass pct. After Zn removal, a Ni alloy containing Ni with a purity of 85.3 to 86.1 mass pct and negligible quantities (<0.1 mass pct) of Re and Ta was obtained. Moreover, recovered Zn metal after distillation had a purity of more than 99.9 mass pct. Therefore, this process could be an environmentally sound recycling process that can recover Ni from superalloy scraps without the consumption of Zn or the generation of toxic wastes solutions.

19 CFR 10.41a - Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of international...

Code of Federal Regulations, 2014 CFR

2014-04-01

... for inspection by Customs officials upon reasonable notice. (3) If the container does not exit the U.S... 19 Customs Duties 1 2014-04-01 2014-04-01 false Lift vans, cargo vans, shipping tanks, skids... Traffic § 10.41a Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of...

19 CFR 10.41a - Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of international...

Code of Federal Regulations, 2012 CFR

2012-04-01

... for inspection by Customs officials upon reasonable notice. (3) If the container does not exit the U.S... 19 Customs Duties 1 2012-04-01 2012-04-01 false Lift vans, cargo vans, shipping tanks, skids... Traffic § 10.41a Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of...

19 CFR 10.41a - Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of international...

Code of Federal Regulations, 2013 CFR

2013-04-01

... for inspection by Customs officials upon reasonable notice. (3) If the container does not exit the U.S... 19 Customs Duties 1 2013-04-01 2013-04-01 false Lift vans, cargo vans, shipping tanks, skids... Traffic § 10.41a Lift vans, cargo vans, shipping tanks, skids, pallets, and similar instruments of...

New Innovations in Highly Ion Specific Media for Recalcitrant Waste stream Radioisotopes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denton, M. S.; Wilson, J.; Ahrendt, M.

Specialty ion specific media were examined and developed for, not only pre- and post-outage waste streams, but also for very difficult outage waste streams. This work was carried out on first surrogate waste streams, then laboratory samples of actual waste streams, and, finally, actual on-site waste streams. This study was particularly focused on PWR wastewaters such as Floor Drain Tank (FDT), Boron Waste Storage Tank (BWST), and Waste Treatment Tank (WTT, or discharge tank). Over the last half decade, or so, treatment technologies have so greatly improved and discharge levels have become so low, that certain particularly problematic isotopes, recalcitrantmore » to current treatment skids, are all that remain prior to discharge. In reality, they have always been present, but overshadowed by the more prevalent and higher activity isotopes. Such recalcitrants include cobalt, especially Co 58 [both ionic/soluble (total dissolved solids, TDS) and colloidal (total suspended solids, TSS)] and antimony (Sb). The former is present in most FDT and BWST wastewaters, while the Sb is primarily present in BWST waste streams. The reasons Co 58 can be elusive to granulated activated carbon (GAC), ultrafiltration (UF) and ion exchange (IX) demineralizers is that it forms submicron colloids as well as has a tendency to form metal complexes with chelating agents (e.g., ethylene diamine tetraacetic acid, or EDTA). Such colloids and non-charged complexes will pass through the entire treatment skid. Antimony (Sb) on the other hand, has little or no ionic charge, and will, likewise, pass through both the filtration and de-min skids into the discharge tanks. While the latter will sometimes (the anionic vs. the cationic or neutral species) be removed on the anion bed(s), it will slough off (snow-plow effect) when a higher affinity anion (iodine slugs, etc.) comes along; thus causing effluents not meeting discharge criteria. The answer to these problems found in this study, during an

Scrap melting model for steel converter founded on interfacial solid/liquid phenomena

NASA Astrophysics Data System (ADS)

Kruskopf, Ari; Holappa, Lauri

2017-12-01

The primary goal in steel converter operation is the removal of carbon from the hot metal. This is achieved by blowing oxygen into the melt. The oxidation of carbon produces a lot of heat. To avoid too high temperatures in the melt cold scrap (recycled steel) is charged into the converter. The melting rate is affected by heat and carbon mass transfer. A process model for steel converter is in development. This model is divided into several modules, which are fluid dynamics, heat- and mass-transfer, scrap melting and chemical reactions. This article focuses on the development of the scrap melting module. A numerical model for calculating temperature and carbon concentration in the melt is presented. The melt model is connected with the solid scrap model via solid/liquid interface. The interface model can take into account solidification of iron melt, melting of solidified layer, a situation without such phase changes, and scrap melting. The aim is to predict the melting rate of the scrap including the properties of the hot metal. The model is tested by calculating the melting rates for different scrap thicknesses. All of the stages in the interface model were taking place in the test calculations.

Scrapping of student bursaries confirmed.

PubMed

Longhurst, Chris

2016-07-27

Student bursaries for nurses will be scrapped from next year, the government has confirmed. Undergraduate nursing and midwifery students in England will now face tuition fees and student loans from August 2017.

Electroextraction of boron from boron carbide scrap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jain, Ashish; Anthonysamy, S., E-mail: sas@igcar.gov.in; Ghosh, C.

2013-10-15

Studies were carried out to extract elemental boron from boron carbide scrap. The physicochemical nature of boron obtained through this process was examined by characterizing its chemical purity, specific surface area, size distribution of particles and X-ray crystallite size. The microstructural characteristics of the extracted boron powder were analyzed by using scanning electron microscopy and transmission electron microscopy. Raman spectroscopic examination of boron powder was also carried out to determine its crystalline form. Oxygen and carbon were found to be the major impurities in boron. Boron powder of purity ∼ 92 wt. % could be produced by the electroextraction processmore » developed in this study. Optimized method could be used for the recovery of enriched boron ({sup 10}B > 20 at. %) from boron carbide scrap generated during the production of boron carbide. - Highlights: • Recovery of {sup 10}B from nuclear grade boron carbide scrap • Development of process flow sheet • Physicochemical characterization of electroextracted boron • Microscopic examination of electroextracted boron.« less

Global perspectives on e-waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widmer, Rolf; Oswald-Krapf, Heidi; Sinha-Khetriwal, Deepali

2005-07-15

Electronic waste, or e-waste, is an emerging problem as well as a business opportunity of increasing significance, given the volumes of e-waste being generated and the content of both toxic and valuable materials in them. The fraction including iron, copper, aluminium, gold and other metals in e-waste is over 60%, while pollutants comprise 2.70%. Given the high toxicity of these pollutants especially when burned or recycled in uncontrolled environments, the Basel Convention has identified e-waste as hazardous, and developed a framework for controls on transboundary movement of such waste. The Basel Ban, an amendment to the Basel Convention that hasmore » not yet come into force, would go one step further by prohibiting the export of e-waste from developed to industrializing countries. Section 1 of this paper gives readers an overview on the e-waste topic-how e-waste is defined, what it is composed of and which methods can be applied to estimate the quantity of e-waste generated. Considering only PCs in use, by one estimate, at least 100 million PCs became obsolete in 2004. Not surprisingly, waste electrical and electronic equipment (WEEE) today already constitutes 8% of municipal waste and is one of the fastest growing waste fractions. Section 2 provides insight into the legislation and initiatives intended to help manage these growing quantities of e-waste. Extended Producer Responsibility (EPR) is being propagated as a new paradigm in waste management. The European Union's WEEE Directive, which came into force in August of 2004, makes it incumbent on manufacturers and importers in EU states to take back their products from consumers and ensure environmentally sound disposal. WEEE management in industrializing countries has its own characteristics and problems, and therefore this paper identifies some problems specific to such countries. The risky process of extracting copper from printed wiring boards is discussed as an example to illustrate the hazards of the

100. INTERIOR OF SKID 9A: VENT VALVE AND RELIEF VALVE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

100. INTERIOR OF SKID 9A: VENT VALVE AND RELIEF VALVE FOR RAPID-LOAD LIQUID OXYGEN TANK - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

E-waste hazard: The impending challenge

PubMed Central

Pinto, Violet N.

2008-01-01

Electronic waste or e-waste is one of the rapidly growing problems of the world. E-waste comprises of a multitude of components, some containing toxic substances that can have an adverse impact on human health and the environment if not handled properly. In India, e-waste management assumes greater significance not only due to the generation of its own e-waste but also because of the dumping of e-waste from developed countries. This is coupled with India's lack of appropriate infrastructure and procedures for its disposal and recycling. This review article provides a concise overview of India's current e-waste scenario, namely magnitude of the problem, environmental and health hazards, current disposal and recycling operations, existing legal framework, organizations working on this issue and recommendations for action. PMID:20040981

E-waste hazard: The impending challenge.

PubMed

Pinto, Violet N

2008-08-01

Electronic waste or e-waste is one of the rapidly growing problems of the world. E-waste comprises of a multitude of components, some containing toxic substances that can have an adverse impact on human health and the environment if not handled properly. In India, e-waste management assumes greater significance not only due to the generation of its own e-waste but also because of the dumping of e-waste from developed countries. This is coupled with India's lack of appropriate infrastructure and procedures for its disposal and recycling. This review article provides a concise overview of India's current e-waste scenario, namely magnitude of the problem, environmental and health hazards, current disposal and recycling operations, existing legal framework, organizations working on this issue and recommendations for action.

Co-disposal of electronic waste with municipal solid waste in bioreactor landfills.

PubMed

Visvanathan, C; Visvanthan, C; Yin, Nang Htay; Karthikeyan, Obuli P

2010-12-01

Three pilot scale lysimeters were adopted to evaluate the stability pattern and leaching potential of heavy metals from MSW landfills under the E-waste co-disposed condition. One lysimeter served as control and solely filled with MSW, whereas the other two lysimeters were provided with 10% and 25% of E-waste scraps (% by weight), respectively. The reactors were monitored over a period of 280 days at ambient settings with continuous leachate recirculation. Stabilization pattern of carbon appears to be more than 50% in all the three lysimeters with irrespective of their operating conditions. Iron and zinc concentrations were high in leachate during bioreactor landfill operation and correlating with the TCLP leachability test results. In contrast, Pb concentration was around <0.6 mg/L, but which showed maximum leaching potential under TCLP test conditions. But, no heavy metal accumulation was found with leachate recirculation practices in lysimeters. Mobility of the metal content from the E-waste was found to be amplified with the long term disposal or stabilization within landfills. The results showed that the TCLP test cannot be completely reliable tool for measuring long-term leachability of toxic substances under landfill condition; rather landfill lysimeter studies are necessary to get the real scenario. Copyright © 2010 Elsevier Ltd. All rights reserved.

Update on Recovering Lead From Scrap Batteries

NASA Astrophysics Data System (ADS)

Cole, E. R.; Lee, A. Y.; Paulson, D. L.

1985-02-01

Previous work at the Bureau of Mines Rolla Research Center, U.S. Department of the Interior, resulted in successful development of a bench-scale, combination electrorefining-electrowinning method for recycling lead from scrap batteries by using waste fluosilicic acid (H2SiF6) as electrolyte.1,2 This paper describes larger scale experiments. Prior attempts to electrowin lead failed because large quantities of insoluble lead dioxide were deposited on the anodes at the expense of lead deposition on the cathodes. A major breakthrough was achieved with the discovery that lead dioxide formation at the anodes is prevented by adding a small amount of phosphorus to the electrolyte. The amount of PbO2 formed on the anodes during lead electrowinning was less than 1% of the total lead deposited on the cathodes. This work recently won the prestigious IR·100 award as one of the 100 most significant technological advances of 1984.

Vertical Drop Testing and Analysis of the WASP Helicopter Skid Gear

NASA Technical Reports Server (NTRS)

Fuchs, Yvonne T.; Jackson, Karen E.

2008-01-01

Human occupant modeling and injury risk assessment have been identified as areas of research for improved prediction of rotorcraft crashworthiness within the NASA Aeronautics Program's Subsonic Rotary Wing Project. As part of this effort, an experimental program was conducted to assess the impact performance of a skid gear for use on the WASP kit-built helicopter, which is marketed by HeloWerks, Inc. of Hampton, Virginia. Test data from a drop test at an impact velocity of 8.4 feet-per-second were used to assess a finite element model of the skid gear test article. This assessment included human occupant analytic models developed for execution in LS-DYNA. The test article consisted of an aluminum skid gear mounted beneath a steel plate. A seating platform was attached to the upper surface of the steel plate, and two 95th percentile Hybrid III male Aerospace Anthropomorphic Test Devices (ATDs) were seated on the platform and secured using a four-point restraint system. The goal of the test-analysis correlation is to further the understanding of LS-DYNA ATD occupant models and responses in the vertical (or spinal) direction. By correlating human occupant experimental test data for a purely vertical impact with the LS-DYNA occupant responses, improved confidence in the use of these tools and better understanding of the limitations of the automotive-based occupant models for aerospace application can begin to be developed.

Vertical Drop Testing and Analysis of the WASP Helicopter Skid Gear

NASA Technical Reports Server (NTRS)

Fuchs, Yvonne T.; Jackson, Karen E.

2008-01-01

Human occupant modeling and injury risk assessment have been identified as areas of research for improved prediction of rotorcraft crashworthiness within the NASA Aeronautics Program s Subsonic Rotary Wing Project. As part of this effort, an experimental program was conducted to assess the impact performance of a skid gear for use on the WASP kit-built helicopter, which is marketed by HeloWerks, Inc. of Hampton, Virginia. Test data from a drop test at an impact velocity of 8.4 feet-per-second were used to assess a finite element model of the skid gear test article. This assessment included human occupant analytic models developed for execution in LS-DYNA. The test article consisted of an aluminum skid gear mounted beneath a steel plate. A seating platform was attached to the upper surface of the steel plate, and two 95th percentile Hybrid III male Aerospace Anthropomorphic Test Devices (ATDs) were seated on the platform and secured using a four-point restraint system. The goal of the test-analysis correlation is to further the understanding of LS-DYNA ATD occupant models and responses in the vertical (or spinal) direction. By correlating human occupant experimental test data for a purely vertical impact with the LS-DYNA occupant responses, improved confidence in the use of these tools and better understanding of the limitations of the automotive-based occupant models for aerospace application can begin to be developed.

Final Environmental Assessment for the Skid Strip Area Development Plan at Cape Canaveral Air Force Station Florida

DTIC Science & Technology

2009-07-01

including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215...Canaveral Air Force Station (CCAFS) Skid Strip. Since the facility no longer operates as a missile skid strip, it is referred to as the "Airfield...construction of a new 65 foot tall control tower; construction of a new Airfield Manager (AM) Operations Building that would adjoin the new tower; and

Durability of certain configurations for providing skid resistance on concrete pavements.

DOT National Transportation Integrated Search

1974-01-01

The main objective of this study was to establish the factors that influence the durability of the surface configurations that are used or can be used to provide high and long lasting skid resistance for portland cement concrete pavements. In the dev...

46 CFR 148.265 - Fish meal or fish scrap.

Code of Federal Regulations, 2011 CFR

2011-10-01

... a maximum of 15 percent fat by weight. (c) At the time of production, fish meal or fish scrap must... antioxidant at the time of shipment. (f) At the time of loading, the temperature of the fish meal or fish... fish meal or fish scrap at the time of shipment; (5) The date of production of the material; and (6...

Synthesis of submicron silver powder from scrap low-temperature co-fired ceramic an e-waste: Understanding the leaching kinetics and wet chemistry.

PubMed

Swain, Basudev; Shin, Dongyoon; Joo, So Yeong; Ahn, Nak Kyoon; Lee, Chan Gi; Yoon, Jin-Ho

2018-03-01

The current study focuses on the understanding of leaching kinetics of metal in the LTCC in general and silver leaching in particular along with wet chemical reduction involving silver nanoparticle synthesis. Followed by metal leaching, the silver was selectively precipitated using HCl as AgCl. The precipitated AgCl was dissolved in ammonium hydroxide and reduced to pure silver metal nanopowder (NPs) using hydrazine as a reductant. Polyvinylpyrrolidone (PVP) used as a stabilizer and Polyethylene glycol (PEG) used as reducing reagent as well as stabilizing reagent to control size and shape of the Ag NPs. An in-depth investigation indicated a first-order kinetics model fits well with high accuracy among all possible models. Activation energy required for the first order reaction was 21.242 kJ mol -1 for Silver. PVP and PEG 1% each together provide better size control over silver nanoparticle synthesis using 0.4 M hydrazine as reductant, which provides relatively regular morphology in comparison to their individual application. The investigation revealed that the waste LTCC (an industrial e-waste) can be recycled through the reported process even in industrial scale. The novelty of reported recycling process is simplicity, versatile and eco-efficiency through which waste LTCC recycling can address various issues like; (i) industrial waste disposal (ii) synthesis of silver nanoparticles from waste LTCC (iii) circulate metal economy within a closed loop cycle in the industrial economies where resources are scarce, altogether. Copyright © 2017 Elsevier Ltd. All rights reserved.

46 CFR Sec. 12 - Disposition of removed equipment and scrap.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Disposition of removed equipment and scrap. Sec. 12... CONTRACT-NSA-LUMPSUMREP Sec. 12 Disposition of removed equipment and scrap. (a) Article 8 of the NSA-LUMPSUMREP Contract provides that any ship equipment, fuel, lube oil, supplies, stores, furniture, fixtures...

Development and fabrication of the Virginia skid-resistance measurement vehicle (model 2).

DOT National Transportation Integrated Search

1970-01-01

The inefficiency of the Virginia Highway Research Council, Model 1, skid measurement trailer, and the increasing effort expended by the American Society for Testing and Materials toward the development of more stringent specifications for pavement sk...

Process for removing copper in a recoverable form from solid scrap metal

DOEpatents

Hartman, Alan D.; Oden, Laurance L.; White, Jack C.

1995-01-01

A process for removing copper in a recoverable form from a copper/solid ferrous scrap metal mix is disclosed. The process begins by placing a copper/solid ferrous scrap metal mix into a reactor vessel. The atmosphere within the reactor vessel is purged with an inert gas or oxidizing while the reactor vessel is heated in the area of the copper/solid ferrous scrap metal mix to raise the temperature within the reactor vessel to a selected elevated temperature. Air is introduced into the reactor vessel and thereafter hydrogen chloride is introduced into the reactor vessel to obtain a desired air-hydrogen chloride mix. The air-hydrogen chloride mix is operable to form an oxidizing and chloridizing atmosphere which provides a protective oxide coating on the surface of the solid ferrous scrap metal in the mix and simultaneously oxidizes/chloridizes the copper in the mix to convert the copper to a copper monochloride gas for transport away from the solid ferrous scrap metal. After the copper is completely removed from the copper/solid ferrous scrap metal mix, the flows of air and hydrogen chloride are stopped and the copper monochloride gas is collected for conversion to a recoverable copper species.

CHEMICAL RECLAMATION OF SCRAP RUBBER

EPA Science Inventory

A conceptual, commercial-scale plant design was formulated for processing 22,500 t/yr of scrap rubber tires to hydrocarbon fuel gases, oils, petrochemicals (principally ethylene and aromatic liquids), and carbon black. The process is based upon molten salt (zinc chloride) pyrolys...

16 CFR 300.29 - Garments or products composed of or containing miscellaneous cloth scraps.

Code of Federal Regulations, 2013 CFR

2013-01-01

... containing miscellaneous cloth scraps. 300.29 Section 300.29 Commercial Practices FEDERAL TRADE COMMISSION... Labeling § 300.29 Garments or products composed of or containing miscellaneous cloth scraps. (a) For wool products which consist of, or are made from, miscellaneous cloth scraps comprising manufacturing by...

16 CFR 300.29 - Garments or products composed of or containing miscellaneous cloth scraps.

Code of Federal Regulations, 2014 CFR

2014-01-01

... containing miscellaneous cloth scraps. 300.29 Section 300.29 Commercial Practices FEDERAL TRADE COMMISSION... Labeling § 300.29 Garments or products composed of or containing miscellaneous cloth scraps. (a) For wool products which consist of, or are made from, miscellaneous cloth scraps comprising manufacturing by...

16 CFR 300.29 - Garments or products composed of or containing miscellaneous cloth scraps.

Code of Federal Regulations, 2012 CFR

2012-01-01

... containing miscellaneous cloth scraps. 300.29 Section 300.29 Commercial Practices FEDERAL TRADE COMMISSION... Labeling § 300.29 Garments or products composed of or containing miscellaneous cloth scraps. (a) For wool products which consist of, or are made from, miscellaneous cloth scraps comprising manufacturing by...

16 CFR 300.29 - Garments or products composed of or containing miscellaneous cloth scraps.

Code of Federal Regulations, 2010 CFR

2010-01-01

... containing miscellaneous cloth scraps. 300.29 Section 300.29 Commercial Practices FEDERAL TRADE COMMISSION... Labeling § 300.29 Garments or products composed of or containing miscellaneous cloth scraps. (a) For wool products which consist of, or are made from, miscellaneous cloth scraps comprising manufacturing by...

16 CFR 300.29 - Garments or products composed of or containing miscellaneous cloth scraps.

Code of Federal Regulations, 2011 CFR

2011-01-01

... containing miscellaneous cloth scraps. 300.29 Section 300.29 Commercial Practices FEDERAL TRADE COMMISSION... Labeling § 300.29 Garments or products composed of or containing miscellaneous cloth scraps. (a) For wool products which consist of, or are made from, miscellaneous cloth scraps comprising manufacturing by...

Complex deformation routes for direct recycling aluminium alloy scrap via industrial hot extrusion

NASA Astrophysics Data System (ADS)

Paraskevas, Dimos; Kellens, Karel; Kampen, Carlos; Mohammadi, Amirahmad; Duflou, Joost R.

2018-05-01

This paper presents the final results of an industrial project, aiming for direct hot extrusion of wrought aluminium alloy scrap at an industrial scale. Two types of complex deformation/extrusion routes were tested for the production of the same profile, starting from AA6060 scrap in form of machining chips. More specifically scrap-based billets were extruded through: a 2-porthole and a 4-porthole die-set, modified for enhanced scrap consolidation and grain refinement. For comparison reasons, cast billets of the same alloy were extruded through the modified 2-porthole die set. The tensile testing results as well as microstructural investigations show that the 4-porthole extrusion route further improves scrap consolidation compared to the 2-porthole die output. The successful implementation of solid state recycling, directly at industrial level, indicates the technological readiness level of this research.

Skidding with horses to thin young stands in western Washington.

Treesearch

Norman P. Worthington

1957-01-01

Increased use of commercial thinning to provide an additional source of needed raw material and to boost overall yields from forest lands has again brought horses into the northwest woods. They are particularly well adapted to skidding small logs under the light, frequent cuts typical of a thinning operation. Horses can, moreover, work at close quarters in a young...

Full-Tree SKidding Black Spruce: Another Way to Favor Reproduction

Treesearch

William F. Johnston

1975-01-01

An alternative to burning is needed for clearcut peatlands where only slash disposal is required to rapidly reproduce black spruce. A 2-year trial in north-central Minnesota indicates that reproduction will be rapid after full-tree skidding on nonbrushy sites taht have well-distribted sphagnum seedbeds and ample natural seeding. Broadcast burning is still recommended...

Catch me if you can: Comparing ballast water sampling skids to traditional net sampling

NASA Astrophysics Data System (ADS)

Bradie, Johanna; Gianoli, Claudio; Linley, Robert Dallas; Schillak, Lothar; Schneider, Gerd; Stehouwer, Peter; Bailey, Sarah

2018-03-01

With the recent ratification of the International Convention for the Control and Management of Ships' Ballast Water and Sediments, 2004, it will soon be necessary to assess ships for compliance with ballast water discharge standards. Sampling skids that allow the efficient collection of ballast water samples in a compact space have been developed for this purpose. We ran 22 trials on board the RV Meteor from June 4-15, 2015 to evaluate the performance of three ballast water sampling devices (traditional plankton net, Triton sampling skid, SGS sampling skid) for three organism size classes: ≥ 50 μm, ≥ 10 μm to < 50 μm, and < 10 μm. Natural sea water was run through the ballast water system and untreated samples were collected using paired sampling devices. Collected samples were analyzed in parallel by multiple analysts using several different analytic methods to quantify organism concentrations. To determine whether there were differences in the number of viable organisms collected across sampling devices, results were standardized and statistically treated to filter out other sources of variability, resulting in an outcome variable representing the mean difference in measurements that can be attributed to sampling devices. These results were tested for significance using pairwise Tukey contrasts. Differences in organism concentrations were found in 50% of comparisons between sampling skids and the plankton net for ≥ 50 μm, and ≥ 10 μm to < 50 μm size classes, with net samples containing either higher or lower densities. There were no differences for < 10 μm organisms. Future work will be required to explicitly examine the potential effects of flow velocity, sampling duration, sampled volume, and organism concentrations on sampling device performance.

Taiwan`s experience with municipal waste recycling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, C.H.

1998-12-31

Currently, each person on the average produces 1.15 kg of the municipal waste per day and a total of 9 million metric tons were generated annually in Taiwan. The disposal of such a huge amount of waste presents tremendous challenge for the island due to the scarcity of landfills and incineration facilities available locally. EPA of Taiwan, R.O.C. thus takes an active role in promoting waste recycling to reduce the garbage produced in municipalities. In order to efficiently utilize the government`s human and financial resources used in recycling, started from January 31, 1989, EPA has mandated the producer responsibility recyclingmore » program for several designated post-consumer products such as PET, PVC bottles, scrap tires, scrap motor vehicles, etc. Producer responsibility recycling program specifies that the manufacturers, importers and sellers of these designated products have the responsibility to retrieve their products and recycle them properly. Several negative effects have been encountered while the implementation of this producer responsibility recycling program in Taiwan which resulted in a modification of this recycling program recently. This paper presents the encountered experiences on the implementation of municipal waste recycling program in Taiwan.« less

Polybrominated diphenyl ethers in e-waste: Level and transfer in a typical e-waste recycling site in Shanghai, Eastern China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Yue; Duan, Yan-Ping, E-mail: duanyanping@tongji.edu.cn; Huang, Fan

Highlights: • PBDEs were detected in the majority of e-waste. • PBDEs were found in TVs made in China after 1990. • The levels of ΣPBDEs in e-waste made in Japan far exceed the threshold limit of RoHS. • The inappropriate recycling and disposal of e-waste is an important source of PBDEs. - Abstract: Very few data for polybrominated diphenyl ethers (PBDEs) were available in the electronic waste (e-waste) as one of the most PBDEs emission source. This study reported concentrations of PBDEs in e-waste including printer, rice cooker, computer monitor, TV, electric iron and water dispenser, as well asmore » dust from e-waste, e-waste dismantling workshop and surface soil from inside and outside of an e-waste recycling plant in Shanghai, Eastern China. The results showed that PBDEs were detected in the majority of e-waste, and the concentrations of ΣPBDEs ranged from not detected to 175 g/kg, with a mean value of 10.8 g/kg. PBDEs were found in TVs made in China after 1990. The mean concentrations of ΣPBDEs in e-waste made in Korea, Japan, Singapore and China were 1.84 g/kg, 20.5 g/kg, 0.91 g/kg, 4.48 g/kg, respectively. The levels of ΣPBDEs in e-waste made in Japan far exceed the threshold limit of RoHS (1.00 g/kg). BDE-209 dominated in e-waste, accounting for over 93%. The compositional patterns of PBDEs congeners resembled the profile of Saytex 102E, indicating the source of deca-BDE. Among the samples of dust and surface soil from a typical e-waste recycling site, the highest concentrations of Σ{sub 18}PBDEs and BDE-209 were found in dust in e-waste, ranging from 1960 to 340,710 ng/g and from 910 to 320,400 ng/g, which were 1–2 orders of magnitude higher than other samples. It suggested that PBDEs released from e-waste via dust, and then transferred to surrounding environment.« less

Recycling of CdTe photovoltaic waste

DOEpatents

Goozner, Robert E.; Long, Mark O.; Drinkard, Jr., William F.

1999-01-01

A method for extracting and reclaiming metals from scrap CdTe photovoltaic cells and manufacturing waste by leaching the waste with a leaching solution comprising nitric acid and water, skimming any plastic material from the top of the leaching solution, separating the glass substrate from the liquid leachate and electrolyzing the leachate to separate Cd from Te, wherein the Te is deposits onto a cathode while the Cd remains in solution.

29 CFR 570.128 - Loading of certain scrap paper balers and paper box compactors.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 3 2011-07-01 2011-07-01 false Loading of certain scrap paper balers and paper box... Amended Exemptions § 570.128 Loading of certain scrap paper balers and paper box compactors. (a) Section... 16- and 17-year-olds to load, but not operate or unload, certain power-driven scrap paper balers and...

7 CFR 30.8 - Scrap.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND STANDARDS Classification of Leaf Tobacco Covering Classes, Types and Groups of Grades § 30.8 Scrap. A byproduct from handling leaf tobacco in both the unstemmed and stemmed forms, consisting of loose and tangled portions of tobacco leaves, floor sweepings, and all other tobacco materials (except stems...

7 CFR 30.8 - Scrap.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND STANDARDS Classification of Leaf Tobacco Covering Classes, Types and Groups of Grades § 30.8 Scrap. A byproduct from handling leaf tobacco in both the unstemmed and stemmed forms, consisting of loose and tangled portions of tobacco leaves, floor sweepings, and all other tobacco materials (except stems...

7 CFR 30.8 - Scrap.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND STANDARDS Classification of Leaf Tobacco Covering Classes, Types and Groups of Grades § 30.8 Scrap. A byproduct from handling leaf tobacco in both the unstemmed and stemmed forms, consisting of loose and tangled portions of tobacco leaves, floor sweepings, and all other tobacco materials (except stems...

7 CFR 30.8 - Scrap.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND STANDARDS Classification of Leaf Tobacco Covering Classes, Types and Groups of Grades § 30.8 Scrap. A byproduct from handling leaf tobacco in both the unstemmed and stemmed forms, consisting of loose and tangled portions of tobacco leaves, floor sweepings, and all other tobacco materials (except stems...

7 CFR 30.8 - Scrap.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND STANDARDS Classification of Leaf Tobacco Covering Classes, Types and Groups of Grades § 30.8 Scrap. A byproduct from handling leaf tobacco in both the unstemmed and stemmed forms, consisting of loose and tangled portions of tobacco leaves, floor sweepings, and all other tobacco materials (except stems...

Refining technology for the recycling of stainless steel radioactive scrap metals, FY 94 bi-annual report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mizia, R.E.; Atteridge, D.G.; Buckentin, J.

1994-08-01

The research addressed under this project is the recycling of metallic nuclear-related by-product materials under the direction of Westinghouse Idaho Nuclear Company (WINCO). The program addresses the recycling of radioactive scrap metals (RSM) for beneficial re-use within the DOE complex; in particular, this program addresses the recycling of stainless steel RSM. It is anticipated that various stainless steel components under WINCO control at the Idaho Falls Engineering Laboratory (INEL), such as fuel pool criticality barriers and fuel storage racks will begin to be recycled in FY94-95. The end product of this recycling effort is expected to be waste and overpackmore » canisters for densified high level waste for the Idaho Waste Immobilization Facility and/or the Universal Canister System for dry (interim) storage of spent fuel. The specific components of this problem area that are presently being, or have been, addressed by CAAMSEC are: (1) the melting/remelting of stainless steel RSM into billet form; (2) the melting/remelting initial research focus will be on the use of radioactive surrogates to study; (3) the cost effectiveness of RSM processing oriented towards privatization of RSM reuse and/or resale. Other components of this problem that may be addressed under program extension are: (4) the melting/remelting of carbon steel; (5) the processing of billet material into product form which shall meet all applicable ASTM requirements; and, (6) the fabrication of an actual prototypical product; the present concept of an end product is a low carbon Type 304/316 stainless steel cylindrical container for densified and/or vitrified high level radioactive waste and/or the Universal Canister System for dry (interim) storage of spent fuel. The specific work reported herein covers the melting/remelting of stainless steel {open_quotes}scrap{close_quotes} metal into billet form and the study of surrogate material removal effectiveness by various remelting techniques.« less

Polybrominated diphenyl ethers in e-waste: level and transfer in a typical e-waste recycling site in Shanghai, Eastern China.

PubMed

Li, Yue; Duan, Yan-Ping; Huang, Fan; Yang, Jing; Xiang, Nan; Meng, Xiang-Zhou; Chen, Ling

2014-06-01

Very few data for polybrominated diphenyl ethers (PBDEs) were available in the electronic waste (e-waste) as one of the most PBDEs emission source. This study reported concentrations of PBDEs in e-waste including printer, rice cooker, computer monitor, TV, electric iron and water dispenser, as well as dust from e-waste, e-waste dismantling workshop and surface soil from inside and outside of an e-waste recycling plant in Shanghai, Eastern China. The results showed that PBDEs were detected in the majority of e-waste, and the concentrations of ΣPBDEs ranged from not detected to 175 g/kg, with a mean value of 10.8 g/kg. PBDEs were found in TVs made in China after 1990. The mean concentrations of ΣPBDEs in e-waste made in Korea, Japan, Singapore and China were 1.84 g/kg, 20.5 g/kg, 0.91 g/kg, 4.48 g/kg, respectively. The levels of ΣPBDEs in e-waste made in Japan far exceed the threshold limit of RoHS (1.00 g/kg). BDE-209 dominated in e-waste, accounting for over 93%. The compositional patterns of PBDEs congeners resembled the profile of Saytex 102E, indicating the source of deca-BDE. Among the samples of dust and surface soil from a typical e-waste recycling site, the highest concentrations of Σ18PBDEs and BDE-209 were found in dust in e-waste, ranging from 1960 to 340,710 ng/g and from 910 to 320,400 ng/g, which were 1-2 orders of magnitude higher than other samples. It suggested that PBDEs released from e-waste via dust, and then transferred to surrounding environment. Copyright © 2013 Elsevier Ltd. All rights reserved.

Felling and skidding productivity and harvesting cost in southern pine forests

Treesearch

R.A. Kluender; B.J. Stokes

1996-01-01

Sixteen stands were harvested at various levels of basal area removed (intensity). Chainsaw felling productivity was more sensitive to stem diameter than harvest intensity. Skidding productivity was highest when removing large trees at high intensity. Harvesting cost was more sensitive to stem size than harvest intensity, although harvest intensity was a very important...

E-waste bans and U.S. households' preferences for disposing of their e-waste.

PubMed

Milovantseva, Natalia; Saphores, Jean-Daniel

2013-07-30

To deal with the inadequate disposal of e-waste, many states have instituted bans on its disposal in municipal landfills. However, the effectiveness of e-waste bans does not seem to have been analyzed yet. This paper starts addressing this gap. Using data from a survey of U.S. households, we estimate multivariate logit models to explain past disposal behavior by households of broken/obsolete ("junk") cell phones and disposal intentions for "junk" TVs. Our explanatory variables include factors summarizing general awareness of environmental issues, pro-environmental behavior in the past year, attitudes toward recycling small electronics (for the cell phones model only), socio-economic and demographic characteristics, and the presence of state e-waste bans. We find that California's Cell Phone Recycling Act had a significant and positive impact on the recycling of junk cell phones; however, state disposal bans for junk TVs seem to have been mostly ineffective, probably because they were poorly publicized and enforced. Their effectiveness could be enhanced by providing more information about e-waste recycling to women, and more generally to adults under 60. Given the disappointing performance of policies implemented to-date to enhance the collection of e-waste, it may be time to explore economic instruments such as deposit-refund systems. Copyright © 2013 Elsevier Ltd. All rights reserved.

Some functional properties of composite material based on scrap tires

NASA Astrophysics Data System (ADS)

Plesuma, Renate; Malers, Laimonis

2013-09-01

The utilization of scrap tires still obtains a remarkable importance from the aspect of unloading the environment from non-degradable waste [1]. One of the most prospective ways for scrap tires reuse is a production of composite materials [2] This research must be considered as a continuation of previous investigations [3, 4]. It is devoted to the clarification of some functional properties, which are considered important for the view of practical applications, of the composite material. Some functional properties of the material were investigated, for instance, the compressive stress at different extent of deformation of sample (till 67% of initial thickness) (LVS EN 826) [5] and the resistance to UV radiation (modified method based on LVS EN 14836) [6]. Experiments were realized on the purposefully selected samples. The results were evaluated in the correlation with potential changes of Shore C hardness (Shore scale, ISO 7619-1, ISO 868) [7, 8]. The results showed noticeable resistance of the composite material against the mechanical influence and ultraviolet (UV) radiation. The correlation with the composition of the material, activity of binder, definite technological parameters, and the conditions supported during the production, were determined. It was estimated that selected properties and characteristics of the material are strongly dependent from the composition and technological parameters used in production of the composite material, and from the size of rubber crumb. Obtained results show possibility to attain desirable changes in the composite material properties by changing both the composition and technological parameters of examined material.

E-waste management in India: A mini-review.

PubMed

Awasthi, Abhishek Kumar; Wang, Mengmeng; Wang, Zhishi; Awasthi, Mrigendra Kumar; Li, Jinhui

2018-05-01

Environmental deterioration and health risk due to improper e-waste management has become a serious issue in India. The major portion of e-waste reaches an unorganized e-waste recycling sector and is then treated by using crude methods. This review article presents a brief highlight on e-waste management status, legislation, and technology uses in India. The present e-waste management needs to be more focused on environmentally sound management, by more active support from all the participants involved in the e-waste flow chain in India.

Wet weather highway accident analysis and skid resistance data management system (volume I).

DOT National Transportation Integrated Search

1992-06-01

The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

EPA Science Inventory

The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

Process for removing cadmium from scrap metal

DOEpatents

Kronberg, J.W.

1994-01-01

A process for the recovery of a metal, in particular, cadmium contained in scrap, in a stable form. The process comprises the steps of mixing the cadmium-containing scrap with an ammonium carbonate solution, preferably at least a stoichiometric amount of ammonium carbonate, and/or free ammonia, and an oxidizing agent to form a first mixture so that the cadmium will react with the ammonium carbonate to form a water-soluble ammine complex; evaporating the first mixture so that ammine complex dissociates from the first mixture leaving carbonate ions to react with the cadmium and form a second mixture that includes cadmium carbonate; optionally adding water to the second mixture to form a third mixture; adjusting the pH of the third mixture to the acid range whereby the cadmium carbonate will dissolve; and adding at least a stoichiometric amount of sulfide, preferably in the form of hydrogen sulfide or an aqueous ammonium sulfide solution, to the third mixture to precipitate cadmium sulfide. This mixture of sulfide is then preferably digested by heating to facilitate precipitation of large particles of cadmium sulfide. The scrap may be divided by shredding or breaking up to exposure additional surface area. Finally, the precipitated cadmium sulfide can be mixed with glass formers and vitrified for permanent disposal.

Process for removing cadmium from scrap metal

DOEpatents

Kronberg, James W.

1995-01-01

A process for the recovery of a metal, in particular, cadmium contained in scrap, in a stable form. The process comprises the steps of mixing the cadmium-containing scrap with an ammonium carbonate solution, preferably at least a stoichiometric amount of ammonium carbonate, and/or free ammonia, and an oxidizing agent to form a first mixture so that the cadmium will react with the ammonium carbonate to form a water-soluble ammine complex; evaporating the first mixture so that ammine complex dissociates from the first mixture leaving carbonate ions to react with the cadmium and form a second mixture that includes cadmium carbonate; optionally adding water to the second mixture to form a third mixture; adjusting the pH of the third mixture to the acid range whereby the cadmium carbonate will dissolve; and adding at least a stoichiometric amount of sulfide, preferably in the form of hydrogen sulfide or an aqueous ammonium sulfide solution, to the third mixture to precipitate cadmium sulfide. This mixture of sulfide is then preferably digested by heating to facilitate precipitation of large particles of cadmium sulfide. The scrap may be divided by shredding or breaking up to expose additional surface area. Finally, the precipitated cadmium sulfide can be mixed with glass formers and vitrified for permanent disposal.

40 CFR 63.10685 - What are the requirements for the control of contaminants from scrap?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Area Sources: Electric Arc Furnace Steelmaking Facilities Standards and Compliance Requirements § 63..., lead, and free organic liquids. For metallic scrap utilized in the EAF at your facility, you must... scrap at your facility subject to paragraph (a)(1) of this section and other scrap subject to paragraph...

40 CFR 63.10685 - What are the requirements for the control of contaminants from scrap?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Area Sources: Electric Arc Furnace Steelmaking Facilities Standards and Compliance Requirements § 63..., lead, and free organic liquids. For metallic scrap utilized in the EAF at your facility, you must... scrap at your facility subject to paragraph (a)(1) of this section and other scrap subject to paragraph...

Skid resistance performance of asphalt wearing courses with electric arc furnace slag aggregates.

PubMed

Kehagia, Fotini

2009-05-01

Metallurgical slags are by-products of the iron and steel industry and are subdivided into blast furnace slag and steel slag according to the different steel-producing processes. In Greece, slags are mostly produced from steelmaking using the electric arc furnace process, and subsequently are either disposed in a random way or utilized by the cement industry. Steel slag has been recently used, worldwide, as hard aggregates in wearing courses in order to improve the skidding resistance of asphalt pavements. At the Highway Laboratory, Department of Civil Engineering of Aristotle University of Thessaloniki research has been carried out in the field of steel slags, and especially in electric arc furnace (EAF) slag, to evaluate their possible use in highway engineering. In this paper, the recent results of anti-skidding performance of steel slag aggregates in highway pavements are presented.

Toward a More Sustainable Trajectory for E-Waste Policy: A Review of a Decade of E-Waste Research in Accra, Ghana.

PubMed

Daum, Kurt; Stoler, Justin; Grant, Richard J

2017-01-29

Global flows of e-waste from the Global North to the Global South continue to damage local environments and harm human health. Weak e-waste regulations and limited use of safety measures for e-waste workers in Accra, Ghana, foster an exploitative environment within the industry, and pose health risks for those working and living near e-waste processing sites. This paper presents an integrated review of over 40 e-waste studies specific to Accra, with particular emphasis on the well-studied e-waste processing site in Agbogbloshie, and synthesizes the existing research base across interdisciplinary themes of human health, environmental health, globalization, trade and informalization, and public policy. Despite significant international attention to Accra's e-waste problem, loopholes within international environmental regulations and treaties provide few incentives and resources for Ghana to strengthen protections for human and environmental health. After a decade of e-waste research in Accra, the crisis continues to intensify; we present a renewed vision for sustainable e-waste policy reform in Ghana and beyond.

Toward a More Sustainable Trajectory for E-Waste Policy: A Review of a Decade of E-Waste Research in Accra, Ghana

PubMed Central

Daum, Kurt; Stoler, Justin; Grant, Richard J.

2017-01-01

Global flows of e-waste from the Global North to the Global South continue to damage local environments and harm human health. Weak e-waste regulations and limited use of safety measures for e-waste workers in Accra, Ghana, foster an exploitative environment within the industry, and pose health risks for those working and living near e-waste processing sites. This paper presents an integrated review of over 40 e-waste studies specific to Accra, with particular emphasis on the well-studied e-waste processing site in Agbogbloshie, and synthesizes the existing research base across interdisciplinary themes of human health, environmental health, globalization, trade and informalization, and public policy. Despite significant international attention to Accra’s e-waste problem, loopholes within international environmental regulations and treaties provide few incentives and resources for Ghana to strengthen protections for human and environmental health. After a decade of e-waste research in Accra, the crisis continues to intensify; we present a renewed vision for sustainable e-waste policy reform in Ghana and beyond. PMID:28146075

Effects of glass scraps powder and glass fiber on mechanical properties of polyester composites

NASA Astrophysics Data System (ADS)

Sonsakul, K.; Boongsood, W.

2017-11-01

One concern in bus manufacturing is the high cost of glass fiber reinforced in polyester composites parts. The composites of glass fiber and polyester are low elongation and high strength, and glass scraps powder displays high hardness and good chemical compatibility with the polymer matrix and glass fiber. This research aimed to study the effects of glass scraps powder and glass fiber on mechanical performance of polyester composites. Glass fiber was randomly oriented fiber and used as new. Glass scraps were obtained from a bus factory and crushed to powder sizes of 120 and 240 μm by a ball mill. Polyester composites were prepared using Vacuum Infusion Process (VIP).Polyester reinforced with 3 layers of glass fiber was an initial condition. Then, one layer of glass fiber was replaced with glass scraps powder. Flexural strength, tensile strength, impact strength and hardness of the polyester composites were determined. Hardness was increased with a combination of smaller size and higher volume of glass scraps powder. Pictures of specimens obtained by using scanning electron microscope (SEM) confirmed that the powder of glass scraps packed in the layers of glass fiber in polyester composites.

Aluminium recovery from waste incineration bottom ash, and its oxidation level.

PubMed

Biganzoli, Laura; Grosso, Mario

2013-09-01

The recovery of aluminium (Al) scraps from waste incineration bottom ash is becoming a common practice in waste management. However, during the incineration process, Al in the waste undergoes oxidation processes that reduce its recycling potential. This article investigates the behaviour of Al scraps in the furnace of two selected grate-fired waste-to-energy plants and the amount recoverable from the bottom ash. About 21-23% of the Al fed to the furnace with the residual waste was recovered and potentially recycled from the bottom ash. Out of this amount, 76-87% was found in the bottom ash fraction above 5 mm and thus can be recovered with standard eddy current separation technology. These values depend on the characteristics and the mechanical strength of the Al items in the residual waste. Considering Al packaging materials, about 81% of the Al in cans can be recovered from the bottom ash as an ingot, but this amount decreases to 51% for trays, 27% for a mix of aluminium and poly-laminated foils and 47% for paper-laminated foils. This shows that the recovery of Al from the incineration residues increases proportionally to the thickness of the packaging.

40 CFR 63.10885 - What are my management practices for metallic scrap and mercury switches?

Code of Federal Regulations, 2013 CFR

2013-07-01

...-consumer automotive body scrap, post-consumer engine blocks, post-consumer oil filters, oily turnings, lead... suppliers throughout the scrap supply chain the need to promote the removal of mercury switches from end-of... the scrap supply chain the need to promote the removal or mercury switches from end-of-life vehicles...

40 CFR 63.10885 - What are my management practices for metallic scrap and mercury switches?

Code of Federal Regulations, 2014 CFR

2014-07-01

...-consumer automotive body scrap, post-consumer engine blocks, post-consumer oil filters, oily turnings, lead... suppliers throughout the scrap supply chain the need to promote the removal of mercury switches from end-of... the scrap supply chain the need to promote the removal or mercury switches from end-of-life vehicles...

40 CFR 63.10885 - What are my management practices for metallic scrap and mercury switches?

Code of Federal Regulations, 2012 CFR

2012-07-01

...-consumer automotive body scrap, post-consumer engine blocks, post-consumer oil filters, oily turnings, lead... suppliers throughout the scrap supply chain the need to promote the removal of mercury switches from end-of... the scrap supply chain the need to promote the removal or mercury switches from end-of-life vehicles...

Design and development of indoor device for recycling of domestic vegetable scrap.

PubMed

Harshitha, Jampala; Krupanidhi, Sreerama; Kumar, Sunil; Wong, Jonathan

2016-01-01

Since the municipal waste management and community garbage-treating systems are in vogue, there is a growing need for the waste minimization to keep our vicinity clean and green. Therefore, a feasible indoor device is designed for recycling domestic vegetable scrap by adopting the principle of soil ecosystem. To arrive at the composting process control parameters in the proposed device, the soil from landfill and quarry along with supplements namely sawdust, cow dung/yeast and the resident thermophilic bacteria are analysed. The soil parameters namely pH, electrical conductivity, Organic carbon, P, K, Fe, moisture content and the presence of thermophilic bacteria varied significantly between negative control sample (NCS) and positive control sample (PCS) and post-treatment positive control group with dried cow dung (PPC-C)-derived compost is soft-textured and homogenous. Furthermore, the double-compartment-based device would be more feasible and appealing as a recycling bin rather than as a refuse storage bin primarily due to the inclusion of dish-plantation. The standardization of composting control parameters is discussed in this article.

41 CFR 109-27.5107 - Recovery of silver from used hypo solution and scrap film.

Code of Federal Regulations, 2014 CFR

2014-01-01

... used hypo solution and scrap film. 109-27.5107 Section 109-27.5107 Public Contracts and Property... § 109-27.5107 Recovery of silver from used hypo solution and scrap film. The requirements for the recovery of silver from used hypo solution and scrap film are contained in § 109-45.1003 of this chapter. ...

41 CFR 109-27.5107 - Recovery of silver from used hypo solution and scrap film.

Code of Federal Regulations, 2012 CFR

2012-01-01

... used hypo solution and scrap film. 109-27.5107 Section 109-27.5107 Public Contracts and Property... § 109-27.5107 Recovery of silver from used hypo solution and scrap film. The requirements for the recovery of silver from used hypo solution and scrap film are contained in § 109-45.1003 of this chapter. ...

41 CFR 109-27.5107 - Recovery of silver from used hypo solution and scrap film.

Code of Federal Regulations, 2013 CFR

2013-07-01

... used hypo solution and scrap film. 109-27.5107 Section 109-27.5107 Public Contracts and Property... § 109-27.5107 Recovery of silver from used hypo solution and scrap film. The requirements for the recovery of silver from used hypo solution and scrap film are contained in § 109-45.1003 of this chapter. ...

41 CFR 109-27.5107 - Recovery of silver from used hypo solution and scrap film.

Code of Federal Regulations, 2011 CFR

2011-01-01

... used hypo solution and scrap film. 109-27.5107 Section 109-27.5107 Public Contracts and Property... § 109-27.5107 Recovery of silver from used hypo solution and scrap film. The requirements for the recovery of silver from used hypo solution and scrap film are contained in § 109-45.1003 of this chapter. ...

41 CFR 109-27.5107 - Recovery of silver from used hypo solution and scrap film.

Code of Federal Regulations, 2010 CFR

2010-07-01

... used hypo solution and scrap film. 109-27.5107 Section 109-27.5107 Public Contracts and Property... § 109-27.5107 Recovery of silver from used hypo solution and scrap film. The requirements for the recovery of silver from used hypo solution and scrap film are contained in § 109-45.1003 of this chapter. ...

Comparing urban solid waste recycling from the viewpoint of urban metabolism based on physical input-output model: A case of Suzhou in China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang Sai, E-mail: liangsai09@gmail.com; Zhang Tianzhu, E-mail: zhangtz@mail.tsinghua.edu.cn

Highlights: Black-Right-Pointing-Pointer Impacts of solid waste recycling on Suzhou's urban metabolism in 2015 are analyzed. Black-Right-Pointing-Pointer Sludge recycling for biogas is regarded as an accepted method. Black-Right-Pointing-Pointer Technical levels of reusing scrap tires and food wastes should be improved. Black-Right-Pointing-Pointer Other fly ash utilization methods should be exploited. Black-Right-Pointing-Pointer Secondary wastes from reusing food wastes and sludge should be concerned. - Abstract: Investigating impacts of urban solid waste recycling on urban metabolism contributes to sustainable urban solid waste management and urban sustainability. Using a physical input-output model and scenario analysis, urban metabolism of Suzhou in 2015 is predicted and impactsmore » of four categories of solid waste recycling on urban metabolism are illustrated: scrap tire recycling, food waste recycling, fly ash recycling and sludge recycling. Sludge recycling has positive effects on reducing all material flows. Thus, sludge recycling for biogas is regarded as an accepted method. Moreover, technical levels of scrap tire recycling and food waste recycling should be improved to produce positive effects on reducing more material flows. Fly ash recycling for cement production has negative effects on reducing all material flows except solid wastes. Thus, other fly ash utilization methods should be exploited. In addition, the utilization and treatment of secondary wastes from food waste recycling and sludge recycling should be concerned.« less

Development of a methodology for electronic waste estimation: A material flow analysis-based SYE-Waste Model.

PubMed

Yedla, Sudhakar

2016-01-01

Improved living standards and the share of services sector to the economy in Asia, and the use of electronic equipment is on the rise and results in increased electronic waste generation. A peculiarity of electronic waste is that it has a 'significant' value even after its life time, and to add complication, even after its extended life in its 'dump' stage. Thus, in Indian situations, after its life time is over, the e-material changes hands more than once and finally ends up either in the hands of informal recyclers or in the store rooms of urban dwellings. This character makes it extremely difficult to estimate electronic waste generation. The present study attempts to develop a functional model based on a material flow analysis approach by considering all possible end uses of the material, its transformed goods finally arriving at disposal. It considers various degrees of uses derived of the e-goods regarding their primary use (life time), secondary use (first degree extension of life), third-hand use (second degree extension of life), donation, retention at the respective places (without discarding), fraction shifted to scrap vendor, and the components reaching the final dump site from various end points of use. This 'generic functional model' named SYE-Waste Model, developed based on a material flow analysis approach, can be used to derive 'obsolescence factors' for various degrees of usage of e-goods and also to make a comprehensive estimation of electronic waste in any city/country. © The Author(s) 2015.

From electronic consumer products to e-wastes: Global outlook, waste quantities, recycling challenges.

PubMed

Tansel, Berrin

2017-01-01

Advancements in technology, materials development, and manufacturing processes have changed the consumer products and composition of municipal solid waste (MSW) since 1960s. Increasing quantities of discarded consumer products remain a major challenge for recycling efforts, especially for discarded electronic products (also referred as e-waste). The growing demand for high tech products has increased the e-waste quantities and its cross boundary transport globally. This paper reviews the challenges associated with increasing e-waste quantities. The increasing need for raw materials (especially for rare earth and minor elements) and unregulated e-waste recycling operations in developing and underdeveloped counties contribute to the growing concerns for e-waste management. Although the markets for recycled materials are increasing; there are major challenges for development of the necessary infrastructure for e-waste management and accountability as well as development of effective materials recovery technologies and product design. Copyright © 2016 Elsevier Ltd. All rights reserved.

Process for removing cadmium from scrap metal

DOEpatents

Kronberg, J.W.

1995-04-11

A process is described for the recovery of a metal, in particular, cadmium contained in scrap, in a stable form. The process comprises the steps of mixing the cadmium-containing scrap with an ammonium carbonate solution, preferably at least a stoichiometric amount of ammonium carbonate, and/or free ammonia, and an oxidizing agent to form a first mixture so that the cadmium will react with the ammonium carbonate to form a water-soluble ammine complex; evaporating the first mixture so that ammine complex dissociates from the first mixture leaving carbonate ions to react with the cadmium and form a second mixture that includes cadmium carbonate; optionally adding water to the second mixture to form a third mixture; adjusting the pH of the third mixture to the acid range whereby the cadmium carbonate will dissolve; and adding at least a stoichiometric amount of sulfide, preferably in the form of hydrogen sulfide or an aqueous ammonium sulfide solution, to the third mixture to precipitate cadmium sulfide. This mixture of sulfide is then preferably digested by heating to facilitate precipitation of large particles of cadmium sulfide. The scrap may be divided by shredding or breaking up to expose additional surface area. Finally, the precipitated cadmium sulfide can be mixed with glass formers and vitrified for permanent disposal. 2 figures.

EMISSIONS FROM BURNING CABINET MAKING SCRAPS

EPA Science Inventory

The report gives results of an initial determination of differences in missions when burning ordinary cordwood compared to kitchen cabinet making scraps. he tests were performed in an instrumented woodstove testing laboratory on a stove that simulated units observed in use at a k...

The effect of material productivity on scrap reduction on aluminum reduction pot process

NASA Astrophysics Data System (ADS)

Huda, L. N.

2018-02-01

Scrap in the production process is defined as part of production that can not be accepted as the final product due to production failure. The amount of scarp occurring in the reduction pot production process of one of the aluminum smelting furnaces exceeds the acceptance standard of 5 to 10%. This affects the amount of production produced. The purpose of this study is to reduce the amount of scrap produced to increase the productivity of the materials used. The solution is carried-out by making improvements using Lean Six Sigma method. In the initial calculation, material productivity ranged from 0.88. Based on the study, the factors that cause the high amount of scrap produced is the use of Na2O which is inserted into the alumina is different in size and the influence of noise that occurs in pots that are difficult to control. The analysis base on Lean Six Sigma obtained process cycle efficiency (PCE) equal to 86,92% for actual condition. Process improvement is carried-out through define, measure, analyze, improve and control procedure on Na2O feeding process and PCE value decrease 6,05%. This indicates that increased process capability will reduce scrap. A decrease in scrap amount of about 6% will be able to increase material productivity by 0.05%. This indicates that continuous process control is needed to decrease the number of scraps and increase productivity.

14 CFR 29.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2012 CFR

2012-01-01

... exceed those obtained in a drop test of the gear with— (i) A drop height of 1.5 times that specified in § 29.725; and (ii) An assumed rotor lift of not more than 1.5 times that used in the limit drop tests...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions...

14 CFR 27.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2012 CFR

2012-01-01

... exceed those obtained in a drop test of the gear with— (i) A drop height of 1.5 times that specified in § 27.725; and (ii) An assumed rotor lift of not more than 1.5 times that used in the limit drop tests...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions...

14 CFR 29.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2014 CFR

2014-01-01

... exceed those obtained in a drop test of the gear with— (i) A drop height of 1.5 times that specified in § 29.725; and (ii) An assumed rotor lift of not more than 1.5 times that used in the limit drop tests...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions...

14 CFR 27.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2014 CFR

2014-01-01

... exceed those obtained in a drop test of the gear with— (i) A drop height of 1.5 times that specified in § 27.725; and (ii) An assumed rotor lift of not more than 1.5 times that used in the limit drop tests...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions...

14 CFR 29.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2013 CFR

2013-01-01

... exceed those obtained in a drop test of the gear with— (i) A drop height of 1.5 times that specified in § 29.725; and (ii) An assumed rotor lift of not more than 1.5 times that used in the limit drop tests...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions...

14 CFR 27.501 - Ground loading conditions: landing gear with skids.

Code of Federal Regulations, 2013 CFR

2013-01-01

... exceed those obtained in a drop test of the gear with— (i) A drop height of 1.5 times that specified in § 27.725; and (ii) An assumed rotor lift of not more than 1.5 times that used in the limit drop tests...) The ground reactions rationally distributed along the bottom of the skid tube. (b) Vertical reactions...

Development potential of e-waste recycling industry in China.

PubMed

Li, Jinhui; Yang, Jie; Liu, Lili

2015-06-01

Waste electrical and electronic equipment (WEEE or e-waste) recycling industries in China have been through several phases from spontaneous informal family workshops to qualified enterprises with treatment fund. This study attempts to analyse the development potential of the e-waste recycling industry in China from the perspective of both time and scale potential. An estimation and forecast of e-waste quantities in China shows that, the total e-waste amount reached approximately 5.5 million tonnes in 2013, with 83% of air conditioners, refrigerators, washing machines, televisions sand computers. The total quantity is expected to reach ca. 11.7 million tonnes in 2020 and 20 million tonnes in 2040, which indicates a large increase potential. Moreover, the demand for recycling processing facilities, the optimal service radius of e-waste recycling enterprises and estimation of the profitability potential of the e-waste recycling industry were analysed. Results show that, based on the e-waste collection demand, e-waste recycling enterprises therefore have a huge development potential in terms of both quantity and processing capacity, with 144 and 167 e-waste recycling facilities needed, respectively, by 2020 and 2040. In the case that e-waste recycling enterprises set up their own collection points to reduce the collection cost, the optimal collection service radius is estimated to be in the range of 173 km to 239 km. With an e-waste treatment fund subsidy, the e-waste recycling industry has a small economic profit, for example ca. US$2.5/unit for television. The annual profit for the e-waste recycling industry overall was about 90 million dollars in 2013. © The Author(s) 2015.

The challenge of electronic waste (e-waste) management in developing countries.

PubMed

Osibanjo, O; Nnorom, I C

2007-12-01

Information and telecommunications technology (ICT) and computer Internet networking has penetrated nearly every aspect of modern life, and is positively affecting human life even in the most remote areas of the developing countries. The rapid growth in ICT has led to an improvement in the capacity of computers but simultaneously to a decrease in the products lifetime as a result of which increasingly large quantities of waste electrical and electronic equipment (e-waste) are generated annually. ICT development in most developing countries, particularly in Africa, depends more on secondhand or refurbished EEEs most of which are imported without confirmatory testing for functionality. As a result large quantities of e-waste are presently being managed in these countries. The challenges facing the developing countries in e-waste management include: an absence of infrastructure for appropriate waste management, an absence of legislation dealing specifically with e-waste, an absence of any framework for end-of-life (EoL) product take-back or implementation of extended producer responsibility (EPR). This study examines these issues as they relate to practices in developing countries with emphasis on the prevailing situation in Nigeria. Effective management of e-waste in the developing countries demands the implementation of EPR, the establishment of product reuse through remanufacturing and the introduction of efficient recycling facilities. The implementation of a global system for the standardization and certification/labelling of secondhand appliances intended for export to developing countries will be required to control the export of electronic recyclables (e-scarp) in the name of secondhand appliances.

E-waste scenario in India, its management and implications.

PubMed

Wath, Sushant B; Dutt, P S; Chakrabarti, T

2011-01-01

Electronic waste or E-waste comprises of old, end-of-life electronic appliances such as computers, laptops, TVs, DVD players, refrigerators, freezers, mobile phones, MP3 players, etc., which have been disposed of by their original users. E-waste contains many hazardous constituents that may negatively impact the environment and affect human health if not properly managed. Various organizations, bodies, and governments of many countries have adopted and/or developed the environmentally sound options and strategies for E-waste management to tackle the ever growing threat of E-waste to the environment and human health. This paper presents E-waste composition, categorization, Global and Indian E-waste scenarios, prospects of recoverable, recyclable, and hazardous materials found in the E-waste, Best Available Practices, recycling, and recovery processes followed, and their environmental and occupational hazards. Based on the discussion, various challenges for E-waste management particularly in India are delineated, and needed policy interventions were discussed.

Environmental impact and human exposure to PCBs in Guiyu, an electronic waste recycling site in China.

PubMed

Xing, Guan Hua; Chan, Janet Kit Yan; Leung, Anna Oi Wah; Wu, Sheng Chun; Wong, M H

2009-01-01

PCB levels in fish (collected from local rivers), atmosphere and human milk samples have been studied to determine the exposure levels of PCBs for local residents and e-waste workers in Guiyu, a major electronic waste scrapping center in China. The source appointment and correlation analyses showed that homologue composition of PCBs in 7 species of fish were consistent and similar to commercial PCBs Aroclor 1248. PCB levels in air surrounding the open burning site were significantly higher than those in residential area. Inhalation exposure contributed 27% and 93% to the total body loadings (the sum of dietary and inhalation exposure) of the local residents, and e-waste workers engaged in open burning respectively. Total PCB concentrations in human milk ranged from N.D. to 57.6 ng/g lipid, with an average of 9.50 ng/g lipid. The present results indicated that commercial PCBs derived from e-waste recycling are major sources of PCBs accumulating in different environmental media, leading to the accumulation of high chlorinated biphenyls in human beings.

Recycling of CdTe photovoltaic waste

DOEpatents

Goozner, Robert E.; Long, Mark O.; Drinkard, Jr., William F.

1999-04-27

A method for extracting and reclaiming metals from scrap CdTe photovoltaic cells and manufacturing waste by leaching the metals in dilute nitric acid, leaching the waste with a leaching solution comprising nitric acid and water, skimming any plastic material from the top of the leaching solution, separating the glass substrate from the liquid leachate, adding a calcium containing base to the leachate to precipitate Cd and Te, separating the precipitated Cd and Te from the leachate, and recovering the calcium-containing base.

The contribution of micro- and macro-texture to the skid resistance of flexible pavement.

DOT National Transportation Integrated Search

2016-02-01

Skid resistance is an important characteristic of the pavement surface to reduce the number of road accidents. The : mechanisms involved in the activation of the frictional force required for a safe braking of the vehicle depend on both : the macro- ...

Characterization of Irradiated and Non-Irradiated Rubber from Automotive Scrap Tires

NASA Astrophysics Data System (ADS)

Souza, Clécia Moura; Silva, Leonardo G.

The aim of this work was to characterize the samples of irradiated and non-irradiated rubber from automotive scrap tires. Rubber samples from scrap tires were irradiated at irradiation doses of 200, 400 and 600kGy in an electron beam accelerator. Subsequently, both the irradiated and non-irradiated samples were characterized by thermogravimetry (TG), differential scanning calorimetry (DSC), tensile strength mechanical test, and Fourier transform infrared (FTIR) spectrophotometry.

Felling and skidding cost estimates for thinnings to reduce gypsy moth impacts

Treesearch

Michael D. Erickson; Curt C. Hassler; Chris B. LeDoux

1991-01-01

The gypsy moth is a serious threat to the hardwood forests of the eastern United States. Although chemical treatments currently exist which can be used to help control the impacts of the moth, silvicultural control measures are just now being proposed and tested. Felling and skidding cost estimates for harvesting merchantable timber under two such proposed...

Economic comparisons of haul road construction versus forwarding versus longer skid distances

Treesearch

Michael D. Erickson; Curt C. Hassler; Chris B. LeDoux

1992-01-01

There currently exists no set of basic guidelines for Appalachian loggers to use in the decision making process for selecting the best way to harvest a tract of timber. Specifically, guidelines are needed for deciding between the alternatives of constructing truck haul roads to access an area or other alternatives such as skidding or forwarding timber longer distances...

The Militarization of the Prairie: Scrap Drives, Metaphors, and the "Omaha World-Herald's" 1942 "Nebraska Plan"

ERIC Educational Resources Information Center

Kimble, James J.

2007-01-01

In WW II, there was no nationwide shortage of scrap on the home front. In backyards, attics, barns, ditches, garages, and factory storage sheds across the country, all sorts of scrap material awaited transport and eventual conversion to arms. Yet the public's awareness of the scrap, and the national willpower necessary to collect it, seemed to be…

Lincoln Co. Scrap Metal, Crab Orchard, Kentucky

EPA Pesticide Factsheets

The City of Crab Orchard, KY (population less than 1,000) received a $200,000 EPA Brownfields cleanup grant in 2010 to cleanup up the Lincoln County ScrapMetal property. The site, a former scrap metal recycler and general junkyard, was located in the middle of downtown. The city has experienced a dramatic decline in growth over the past few years. The abandoned two-acre site is located in the city’s center, directly across the street from City Hall. It is the largest property on Main Street. The property was an eyesore, and posed potential health risks to area residents, and deterred investment. Its blighted status did little to help the commercial and private properties that surround it. The site was also home to a dilapidated building that once served as the Odd Fellows meeting hall.

Recycling Of Cis Photovoltaic Waste

DOEpatents

Drinkard, Jr., William F.; Long, Mark O.; Goozner; Robert E.

1998-07-14

A method for extracting and reclaiming metals from scrap CIS photovoltaic cells and associated photovoltaic manufacturing waste by leaching the waste with dilute nitric acid, skimming any plastic material from the top of the leaching solution, separating glass substrate from the leachate, electrolyzing the leachate to plate a copper and selenium metal mixture onto a first cathode, replacing the cathode with a second cathode, re-electrolyzing the leachate to plate cadmium onto the second cathode, separating the copper from selenium, and evaporating the depleted leachate to yield a zinc and indium containing solid.

Cleaning Up Electronic Waste (E-Waste)

EPA Pesticide Factsheets

While accurate data on the amount of e-waste being exported from the U.S. are not available, the United States government is concerned that these exports are being mismanaged abroad, causing serious public health and environmental hazards.

77 FR 4914 - Consumer Information Regulations; Fees for Use of Traction Skid Pads

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-01

... found at 49 CFR 575.104. To aid consumers in making an informed choice in the purchase of passenger car..., App. B. Several commercial facilities also have traction skid pads. The current fees charged for use... these tires for purchase by manufacturers. Based on NHTSA's assessment using a ``market price'' analysis...

Thermogravimetric characteristics and kinetics of scrap tyre and Juglans regia shell co-pyrolysis.

PubMed

Uzun, B B; Yaman, E

2014-10-01

The degradation kinetics of Juglans regia shell, scrap tyre and their blends were investigated using a thermogravimetric analysis method. Experiments were performed under dynamic conditions and a nitrogen atmosphere in the range 293 to 973 K at different heating rates. During pyrolysis of J. regia shell three mass loss zones were specified as removal of water, decomposition of hemicelluloses and cellulose, and decomposition of lignin. The degradation curves of scrap tyre showed merely one stage which was due to decomposition of styrene butadiene rubber. The kinetic parameters were calculated using both Arrhenius and Coats-Redfern methods. By adopting the Arrhenius method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blends were found to be 69.22, 71.48 and 47.03 kJ mol(-1), respectively. Additionally, by using the Coats-Redfern method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blend were determined as 99.85, 78.72 and 63.81 kJ mol(-1), respectively. The addition of J. regia shell to scrap tyre caused a reduction in the activation energies. The difference of weight loss was measured to examine interactions between raw materials. The maximum difference between experimental and theoretical mass loss was 5% at about 648 K with a heating rate of 20 K min(-1). These results indicated a significant synergistic effect was available during co-pyrolysis of J. regia shell and scrap tyre in the high temperature region. © The Author(s) 2014.

Recycling of CdTe photovoltaic waste

DOEpatents

Goozner, R.E.; Long, M.O.; Drinkard, W.F. Jr.

1999-04-27

A method for extracting and reclaiming metals from scrap CdTe photovoltaic cells and manufacturing waste by leaching the metals in dilute nitric acid, leaching the waste with a leaching solution comprising nitric acid and water, skimming any plastic material from the top of the leaching solution, separating the glass substrate from the liquid leachate, adding a calcium containing base to the leachate to precipitate Cd and Te, separating the precipitated Cd and Te from the leachate, and recovering the calcium-containing base. 3 figs.

Comparing urban solid waste recycling from the viewpoint of urban metabolism based on physical input-output model: A case of Suzhou in China.

PubMed

Liang, Sai; Zhang, Tianzhu

2012-01-01

Investigating impacts of urban solid waste recycling on urban metabolism contributes to sustainable urban solid waste management and urban sustainability. Using a physical input-output model and scenario analysis, urban metabolism of Suzhou in 2015 is predicted and impacts of four categories of solid waste recycling on urban metabolism are illustrated: scrap tire recycling, food waste recycling, fly ash recycling and sludge recycling. Sludge recycling has positive effects on reducing all material flows. Thus, sludge recycling for biogas is regarded as an accepted method. Moreover, technical levels of scrap tire recycling and food waste recycling should be improved to produce positive effects on reducing more material flows. Fly ash recycling for cement production has negative effects on reducing all material flows except solid wastes. Thus, other fly ash utilization methods should be exploited. In addition, the utilization and treatment of secondary wastes from food waste recycling and sludge recycling should be concerned. Copyright © 2011 Elsevier Ltd. All rights reserved.

Wet weather highway accident analysis and skid resistance data management system (volume II : user's manual).

DOT National Transportation Integrated Search

1992-06-01

The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

E-waste issues in Sri Lanka and the Basel Convention.

PubMed

Suraweera, Inoka

2016-03-01

E-waste is hazardous, complex and expensive to treat in an environmentally sound manner. The management of e-waste is considered a serious challenge in both developed and developing countries and Sri Lanka is no exception. Due to significant growth in the economy and investments and other reasons the consumption of electronic and electrical equipment in Sri Lanka has increased over the years resulting in significant generation of e-waste. Several initiatives such as introduction of hazardous waste management rules, ratification of the Basel Convention in 1992 and the introduction of a National Corporate E-waste Management Program have been undertaken in Sri Lanka to manage e-waste. Strengthening policy and legislation, introducing methods for upstream reduction of e-waste, building capacity of relevant officers, awareness raising among school children and the general public and development of an e-waste information system are vital. Research on e-waste needs to be developed in Sri Lanka. The health sector could play a leading role in the provision of occupational health and safety for e-waste workers, advocacy, capacity building of relevant staff and raising awareness among the general public about e-waste. Improper e-waste management practices carried out by informal sector workers need to be addressed urgently in Sri Lanka.

Global responses for recycling waste CRTs in e-waste.

PubMed

Singh, Narendra; Li, Jinhui; Zeng, Xianlai

2016-11-01

The management of used cathode ray tube (CRT) devices is a major problem worldwide due to rapid uptake of the technology and early obsolescence of CRT devices, which is considered an environment hazard if disposed improperly. Previously, their production has grown in step with computer and television demand but later on with rapid technological innovation; TVs and computer screens has been replaced by new products such as Liquid Crystal Displays (LCDs) and Plasma Display Panel (PDPs). This change creates a large volume of waste stream of obsolete CRTs waste in developed countries and developing countries will be becoming major CRTs waste producers in the upcoming years. We studied that there is also high level of trans-boundary movement of these devices as second-hand electronic equipment into developing countries in an attempt to bridge the 'digital divide'. Moreover, the current global production of e-waste is estimated to be '41million tonnes per year' where a major part of the e-waste stream consists of CRT devices. This review article provides a concise overview of world's current CRTs waste scenario, namely magnitude of the demand and processing, current disposal and recycling operations. Copyright © 2016 Elsevier Ltd. All rights reserved.

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

Leather waste--potential threat to human health, and a new technology of its treatment.

PubMed

Kolomaznik, K; Adamek, M; Andel, I; Uhlirova, M

2008-12-30

In this paper, the authors deal with the problem of processing various types of waste generated by leather industry, with special emphasis to chrome-tanned waste. The agent that makes this waste potentially hazardous is hexavalent chromium. Its compounds can have negative effects on human health and some CrVI salts are considered carcinogens. The authors present the risks of spontaneous oxidization of CrIII to CrVI in the open-air dumps as well as the possible risks of wearing bad quality shoes, in which the chromium content is not controlled. There are several ways of handling primary leather waste, but no satisfactory technology has been developed for the secondary waste (manipulation waste, e.g. leather scraps and used leather products). In this contribution, a new three-step hybrid technology of processing manipulation waste is presented and tested under laboratory, pilot-scale and industrial conditions. The filtrate can be used as a good quality NPK fertilizer. The solid product, titanium-chromium sludge, can serve as an inorganic pigment in glass and ceramic industry. Further, the authors propose selective collection of used leather products (e.g. old shoes), the hydrolysable parts of which can be also processed by the new hybrid technology.

Human health risk assessment of lead, manganese and copper from scrapped car paint dust from automobile workshops in Nigeria.

PubMed

Nduka, John Kanayochukwu; Onyenezi Amuka, John Paul; Onwuka, Jude Chinedu; Udowelle, Nnaemeka Arinze; Orisakwe, Orish Ebere

2016-10-01

The economic downturn in Nigeria and Structural Adjustment Programme led to the flooding of Nigerian market with imported used automobiles. Most of these vehicles needed refurbishing and reworking. The present study is a human health risk assessment of metal exposure resulting from reworking of imported used vehicles in Nigeria. Scrap paint dusts from 56 Japanese made cars were collected from 8 different mechanic villages (workshops A-H] in Southeastern Nigeria. Scrap paints were homogenized, mixed, divided into fine particles and digested by standard method. The filtrates were assayed of lead, manganese and copper with atomic absorption spectrophotometry (AAS). Workshop B has the highest concentration of Pb (4.26 ± 0.93). Manganese in workshops A and F were (3.31 ± 0.85) and (3.04 ± 0.47) respectively and were higher than the levels from workshops C, B, D, G and H. Copper in workshop D (7.11 ± 0.21) was significantly greater than the other workshops. The highest hazard quotient (HQ) through ingestion, inhalation and dermal exposures in adults were 9.44E-05 (workshop B), 4.20E-01 (workshop B) and 1.08E-05 (workshop D) respectively. The highest values for HQ through ingestion, inhalation and dermal in children were 8.82E-04, 7.61E-01 and 2.86E-05 all in workshop B respectively. For children, the highest carcinogenic risk levels were 7.05E-08, 6.09E-05 and 2.29E-10 for ingestion, inhalation and dermal exposures respectively. In adults, the carcinogenic risk levels were 7.55E-09, 3.39E-05 and 8.67E-10 for ingestion, inhalation and dermal exposures respectively. Chronic exposure to scrap car paint dusts may be of significant public health importance in Nigeria as this may add to the body burden of some heavy metals.

Hazardous E-waste and its impact on soil structure

NASA Astrophysics Data System (ADS)

Dharini, K.; Cynthia, J. Bernadette; Kamalambikai, B.; Sudar Celestina, J. P. Arul; Muthu, D.

2017-07-01

E-waste disposal has been a significant issue over the past few decades with the development of technology and the plethora of electronic products produced. The inclusive term E-Waste encapsulates various forms of electrical and electronical equipment which provides no value to the current owners and it is one among the fastest growing waste streams. E-Waste is a complex, non-biodegradable waste which is generally dumped in mountain like heaps. These wastes are said to have a large quantities of lead, cadmium, arsenic etc.it is mandatory to dispose such scrupulously since they have the ability to affect the soil and water parameters. Solid waste management is a blooming field which strives to reduce the accumulation of used electronic gadgets. Rainwater gets infiltrated through the e-waste landfill and it leaches through the soil which in turn reaches the groundwater directly thereby affecting the water intended for drinking and domestic purposes. This study focuses on the consequences of toxic waste by comparing the difference in properties of the soil structure prior to and after the e-waste landfill at various concentrations.

Economic and policy instrument analyses in support of the scrap tire recycling program in Taiwan.

PubMed

Chang, Ni-Bin

2008-02-01

Understanding the cost-effectiveness and the role of economic and policy instruments, such as the combined product tax-recycling subsidy scheme or a tradable permit, for scrap tire recycling has been of crucial importance in a market-oriented environmental management system. Promoting product (tire) stewardship on one hand and improving incentive-based recycling policy on the other hand requires a comprehensive analysis of the interfaces and interactions in the nexus of economic impacts, environmental management, environmental valuation, and cost-benefit analysis. This paper presents an assessment of the interfaces and interactions between the implementation of policy instruments and its associated economic evaluation for sustaining a scrap tire recycling program in Taiwan during the era of the strong economic growth of the late 1990s. It begins with an introduction of the management of the co-evolution between technology metrics of scrap tire recycling and organizational changes for meeting the managerial goals island-wide during the 1990s. The database collected and used for such analysis covers 17 major tire recycling firms and 10 major tire manufacturers at that time. With estimates of scrap tire generation and possible scale of subsidy with respect to differing tire recycling technologies applied, economic analysis eventually leads to identify the associated levels of product tax with respect to various sizes of new tires. It particularly demonstrates a broad perspective of how an integrated econometric and engineering economic analysis can be conducted to assist in implementing policy instruments for scrap tire management. Research findings indicate that different subsidy settings for collection, processing, and end use of scrap tires should be configured to ameliorate the overall managerial effectiveness. Removing the existing boundaries between designated service districts could strengthen the competitiveness of scrap tires recycling industry, helping to

Prevention-intervention strategies to reduce exposure to e-waste.

PubMed

Heacock, Michelle; Trottier, Brittany; Adhikary, Sharad; Asante, Kwadwo Ansong; Basu, Nil; Brune, Marie-Noel; Caravanos, Jack; Carpenter, David; Cazabon, Danielle; Chakraborty, Paromita; Chen, Aimin; Barriga, Fernando Diaz; Ericson, Bret; Fobil, Julius; Haryanto, Budi; Huo, Xia; Joshi, T K; Landrigan, Philip; Lopez, Adeline; Magalini, Frederico; Navasumrit, Panida; Pascale, Antonio; Sambandam, Sankar; Aslia Kamil, Upik Sitti; Sly, Leith; Sly, Peter; Suk, Ann; Suraweera, Inoka; Tamin, Ridwan; Vicario, Elena; Suk, William

2018-06-27

As one of the largest waste streams, electronic waste (e-waste) production continues to grow in response to global demand for consumer electronics. This waste is often shipped to developing countries where it is disassembled and recycled. In many cases, e-waste recycling activities are conducted in informal settings with very few controls or protections in place for workers. These activities involve exposure to hazardous substances such as cadmium, lead, and brominated flame retardants and are frequently performed by women and children. Although recycling practices and exposures vary by scale and geographic region, we present case studies of e-waste recycling scenarios and intervention approaches to reduce or prevent exposures to the hazardous substances in e-waste that may be broadly applicable to diverse situations. Drawing on parallels identified in these cases, we discuss the future prevention and intervention strategies that recognize the difficult economic realities of informal e-waste recycling.

Modelling the correlations of e-waste quantity with economic increase.

PubMed

Awasthi, Abhishek Kumar; Cucchiella, Federica; D'Adamo, Idiano; Li, Jinhui; Rosa, Paolo; Terzi, Sergio; Wei, Guoyin; Zeng, Xianlai

2018-02-01

Waste from Electrical and Electronic Equipment (WEEE or e-waste) is regarded as one of the fastest growing waste streams in the world and is becoming an emerging issue owing to adverse consequences on the natural environment and the human health. This research article reveals the presence of a strong linear correlation among global e-waste generation and Gross Domestic Product. The obtained results indicate that the best fit for data can be reached by comparing e-waste collected volumes and GDP PPS. More in detail, an increase of 1000 GDP PPS means an additional 0.27kg of e-waste collected and 0.22kg of e-waste reused/recycled. Furthermore, for each additional citizen, there will be an increase of 7.7kg of e-waste collected and 6.2kg of e-waste reused/recycled. The better collection of e-waste acts an important role concerning the circular economy, and it can be an advantageous approach. Therefore, e-waste could be considered as an opportunity for recycling or recovery of valuable metals (e.g., copper, gold, silver, and palladium), given their significant content in precious metals than in mineral ores. Copyright © 2017 Elsevier B.V. All rights reserved.

System using electric furnace exhaust gas to preheat scrap for steelmaking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takai, K.; Iwasaki, K.

1987-09-08

A method is described for clean preheating of scrap contaminated with oil and organic matter, for steelmaking, using heat from exhaust gas flow from an electric furnace. It consists of: burning any combustibles present in the exhaust gas flow and simultanously separating out dust particles from the exhaust gas flow; heating a predetermined amount of the scrap by heat exchange with a predetermined portion of the exhaust gas flow; removing and collecting dust from the exhaust gas flow after preheating of scrap thereby; sensing the temperature of the exhaust flow; scrubbing the exhaust gas flow with an aqueous solution ofmore » a deodorant solvent flowing at a rate regulated to be in a predetermined relationship related to the exhaust gas temperature sensed prior to scrubbing, thereby generating saturated vapor and reducing the temperature of the exhaust gas flow by a predetermined amount; and electrostatically precipitating out oil mist attached to saturated water vapor and liquid droplets in the exhaust gas flow.« less

A study on the recycling of scrap integrated circuits by leaching.

PubMed

Lee, Ching-Hwa; Tang, Li-Wen; Popuri, Srinivasa R

2011-07-01

In order to minimize the problem of pollution and to conserve limited natural resources, a method to recover the valuable metals such as gold, silver and copper) present in the scrap integrated circuits (ICs) was developed in the present study. Roasting, grinding, screening, magnetic separation, melting and leaching were adopted to investigate the efficiency of recovery of gold, silver and copper from scrap ICs. The collected scrap IC samples were roasted at 850 °C to destroy their plastic resin sealing material, followed by screening and magnetic separation to separate the metals from the resin residue. The non-ferrous materials (0.840 mm) were mainly composed of copper and could be melted into a copper alloy. Non-ferrous materials containing gold (860.05 ppm), silver (1323.12 ppm) and copper (37259.7 ppm) (size less than 50 mesh) were recovered 100% by a leaching process and thiourea was used as a leaching reagent.

E-waste: the growing global problem and next steps.

PubMed

Heacock, Michelle; Kelly, Carol Bain; Suk, William A

2016-03-01

In many low- and middle-income countries, handling and disposal of discarded electrical or electronic equipment (EEE) is frequently unregulated. e-Waste contains hazardous constituents such as lead, mercury, and chromium, certain chemicals in plastics, and flame retardants. There is increasing concern about health effects related to contamination in air, soil, and water for people working and living at or near informal e-waste processing sites, especially to the most vulnerable populations, pregnant women and children. The observed adverse health effects and increasing number of e-waste sites make protecting human health and the environment from e-waste contamination an expanding challenge. Through international cooperation, awareness can be elevated about the harm that e-waste processing poses to human health. Here we discuss how international researchers, public health practitioners, and policymakers can employ solutions to reduce e-waste exposures.

Reconstituted polymeric materials derived from post-consumer waste, industrial scrap and virgin resins made by solid state pulverization

DOEpatents

Khait, Klementina

1998-09-29

A method of making polymeric particulates wherein polymeric scrap material, virgin polymeric material and mixtures thereof are supplied to intermeshing extruder screws which are rotated to transport the polymeric material along their length and subject the polymeric material to solid state shear pulverization and in-situ polymer compatibilization, if two or more incompatible polymers are present. Uniform pulverized particulates are produced without addition of a compatibilizing agent. The pulverized particulates are directly melt processable (as powder feedstock) and surprisingly yield a substantially homogeneous light color product.

Characterization and recovery of polymers from mobile phone scrap.

PubMed

Kasper, Angela C; Bernardes, Andréa M; Veit, Hugo M

2011-07-01

Electronic scrap is part of a universally wide range of obsolete, defective, or used materials that need to be disposed of or recycled in an ecologically friendly manner. The present study focused on the polymers present in mobile phone scrap. In mobile phones, polymers are found in frames and in printed circuit boards (PCBs). The frames are mainly made of polymers whereas PCBs use a variety of material (polymers, ceramics, and metals) which makes recycling more difficult. As a first step, mobile phones were collected, separated by manufacturer/model, and weighed, and the principal polymer types identified. The frames and PCBs were processed separately. The metals in PCBs were separated out by an electrostatic separation process. The resulting polymeric material was identified and mixed with the polymers of frames to fabricate the samples. Two types of samples were made: one with polymeric frames, and the other with a mixture of frames and polymeric fraction from the PCBs. Both kinds of sample were fabricated by injection moulding. The samples were evaluated by mechanical tests (tensile, impact, and hardness) to verify the feasibility of recycling the polymers present in mobile phone scrap. The results demonstrated the technical viability of recovering polymers using mechanical processing followed by an injection process.

Characterization of the High-Speed-Stage Bearing Skidding of Wind Turbine Gearboxes Induced by Dynamic Electricity Grid Events

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helsen, Jan; Guillaume, Patrick; Guo, Yi

Bearing behavior is an important factor for wind turbine drivetrain reliability. Extreme loads and dynamic excitations pose challenges to the bearing design and therefore its performance. Excessive skidding of the bearing rollers should be avoided because it can cause scuffing failures. Excitations coming from wind and the electricity grid can subject the drivetrain to fluctuating torque and nontorque loads. Wind-induced excitations have been investigated predominantly in literature. However, modern wind turbines are subjected more and more to grid-induced loads because of stricter electricity grid regulations. For example, during fault-ride-through events, turbines are required to stay connected for a longer periodmore » of time during the grid failure. This work investigates the influence of electrically induced excitations on the skidding behaviour of the tapered roller bearings on the high-speed stage of a wind turbine gearbox. This skidding behaviour during dynamic events is described as a potential bearing failure initiator by many researchers; however, only limited full-scale dynamic testing is documented. Therefore, a dedicated gridloss-type event is defined in the paper and conducted in a dynamometer test on a full-scale wind turbine nacelle. During the event, a complete electricity grid failure is simulated while the turbine is at rated speed and predefined torque levels. Particular focus is on the characterization of the high-speed shaft tapered roller bearing slip behavior. Strain-gauge bridges in grooves along the circumference of the outer ring are used to characterize the bearing load zone in detail. It is shown that during the torque reversals of the transient event, roller slip can be induced. This indicates the potential of the applied load case to go beyond the preload of the tapered roller bearing. Furthermore, the relation between the applied torque and skidding level is studied.« less

Thermolysis of scrap tire and rubber in sub/super-critical water.

PubMed

Li, Qinghai; Li, Fuxin; Meng, Aihong; Tan, Zhongchao; Zhang, Yanguo

2018-01-01

The rapid growth of waste tires has become a serious environmental issue. Energy and material recovery is regarded as a promising use for waste tires. Thermolysis of scrap tire (ST), natural rubber (NR), and styrene-butadiene rubber (SBR) was carried out in subcritical and supercritical water using a temperature-pressure independent adjustable batch tubular reactor. As a result, oil yields increased as temperature and pressure increased, and they reached maximum values as the state of water was near the critical point. However, further increases in water temperature and pressure reduced the oil yields. The maximum oil yield of 21.21% was obtained at 420 °C and 18 MPa with a reaction time of 40 min. The relative molecular weights of the chemicals in the oil products were in the range of 70-140 g/mole. The oil produced from ST, NR, and SBR contained similar chemical compounds, but the oil yield of SR was between those of NR and SBR. The oil yield from thermolysis of subcritical or supercritical water should be further improved. The main gaseous products, including CH 4 , C 2 H 2 , C 2 H 4 , C 2 H 6 , and C 3 H 8 , increased with reaction time, temperature, and pressure, whereas the solid residues, including carbon black and impurities, decreased. These results provide useful information to develop a sub/super-critical water thermolysis process for energy and material regeneration from waste tires. Copyright © 2017 Elsevier Ltd. All rights reserved.

Global challenges for e-waste management: the societal implications.

PubMed

Magalini, Federico

2016-03-01

Over the last decades the electronics industry and ICT Industry in particular has revolutionized the world: electrical and electronic products have become ubiquitous in today's life around the planet. After use, those products are discarded, sometimes after re-use cycles in countries different from those where they were initially sold; becoming what is commonly called e-waste. Compared to other traditional waste streams, e-waste handling poses unique and complex challenges. e-Waste is usually regarded as a waste problem, which can cause environmental damage and severe human health consequences if not safely managed. e-Waste contains significant amounts of toxic and environmentally sensitive materials and is, thus, extremely hazardous to humans and the environment if not properly disposed of or recycled. On the other hand, e-waste is often seen as a potential source of income for individuals and entrepreneurs who aim to recover the valuable materials (metals in particular) contained in discarded equipment. Recently, for a growing number of people, in developing countries in particular, recycling and separation of e-waste has become their main source of income. In most cases, this is done informally, with no or hardly any health and safety standards, exposing workers and the surrounding neighborhoods to extensive health dangers as well as leading to substantial environmental pollution. Treatment processes of e-waste aim to remove the hazardous components and recover as much reusable material (e.g. metals, glass and plastics) as possible; achieving both objectives is most desired. The paper discuss societal implications of proper e-waste management and key elements to be considered in the policy design at country level.

Innovating e-waste management: From macroscopic to microscopic scales.

PubMed

Zeng, Xianlai; Yang, Congren; Chiang, Joseph F; Li, Jinhui

2017-01-01

Waste electrical and electronic equipment (WEEE or e-waste) has become a global problem, due to its potential environmental pollution and human health risk, and its containing valuable resources (e.g., metals, plastics). Recycling for e-waste will be a necessity, not only to address the shortage of mineral resources for electronics industry, but also to decline environmental pollution and human health risk. To systematically solve the e-waste problem, more attention of e-waste management should transfer from macroscopic to microscopic scales. E-waste processing technology should be significantly improved to diminish and even avoid toxic substance entering into downstream of material. The regulation or policy related to new production of hazardous substances in recycled materials should also be carried out on the agenda. All the findings can hopefully improve WEEE legislation for regulated countries and non-regulated countries. Copyright © 2016 Elsevier B.V. All rights reserved.

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Waste management guidelines. 60.35e... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State...

Emissions of polychlorinated dibenzodioxins and dibenzofurans and polychlorinated biphenyls from uncontrolled burning of garden and domestic waste (backyard burning).

PubMed

Hedman, Björn; Näslund, Morgan; Nilsson, Calle; Marklund, Stellan

2005-11-15

To assess emissions of dioxins (chlorinated dibenzodioxins and dibenzofurans) and PCB from uncontrolled domestic combustion of waste ("backyard burning"), test combustions in barrels and open fires were monitored. The waste fuels used were garden waste, paper, paper and plastic packaging, refuse-derived fuel (RDF), PVC, and electronic scrap. Combustions including PVC and electronic scrap emitted several orders of magnitude more dioxins than the other waste fuels. Emissions from the other fuels had considerable variations, but the levels were difficult to relate to waste composition. Emission factors of PCDD/F and PCB from the backyard burning ranged from 2.2 to 13 000 ng (WHO-TEQ)/kg. The levels found in ash usually were less than 5% of the total. For assessment of total emissions of dioxins and PCB from backyard burning of low and moderately contaminated wastes, an emission factor range of 4-72 ng (WHO-TEQ)/kg is suggested. These figures implythat combusting waste in the backyard could contribute substantially to total emissions, even if the amounts of fuel involved are equivalent to just a few tenths of a percent of the amounts combusted in municipal waste incinerators.

International E-Waste Management Network (IEMN)

EPA Pesticide Factsheets

EPA and the Environmental Protection Administration Taiwan (EPAT) have collaborated since 2011 to build global capacity for the environmentally sound management of waste electrical and electronic equipment (WEEE), which is commonly called e-waste.

"Control-alt-delete": rebooting solutions for the E-waste problem.

PubMed

Li, Jinhui; Zeng, Xianlai; Chen, Mengjun; Ogunseitan, Oladele A; Stevels, Ab

2015-06-16

A number of efforts have been launched to solve the global electronic waste (e-waste) problem. The efficiency of e-waste recycling is subject to variable national legislation, technical capacity, consumer participation, and even detoxification. E-waste management activities result in procedural irregularities and risk disparities across national boundaries. We review these variables to reveal opportunities for research and policy to reduce the risks from accumulating e-waste and ineffective recycling. Full regulation and consumer participation should be controlled and reinforced to improve local e-waste system. Aiming at standardizing best practice, we alter and identify modular recycling process and infrastructure in eco-industrial parks that will be expectantly effective in countries and regions to handle the similar e-waste stream. Toxicity can be deleted through material substitution and detoxification during the life cycle of electronics. Based on the idea of "Control-Alt-Delete", four patterns of the way forward for global e-waste recycling are proposed to meet a variety of local situations.

Reconstituted polymeric materials derived from post-consumer waste, industrial scrap and virgin resins made by solid state pulverization

DOEpatents

Khait, K.

1998-09-29

A method of making polymeric particulates is described wherein polymeric scrap material, virgin polymeric material and mixtures thereof are supplied to intermeshing extruder screws which are rotated to transport the polymeric material along their length and subject the polymeric material to solid state shear pulverization and in-situ polymer compatibilization, if two or more incompatible polymers are present. Uniform pulverized particulates are produced without addition of a compatible agent. The pulverized particulates are directly melt processable (as powder feedstock) and surprisingly yield a substantially homogeneous light color product. 29 figs.

E-waste: an assessment of global production and environmental impacts.

PubMed

Robinson, Brett H

2009-12-20

E-waste comprises discarded electronic appliances, of which computers and mobile telephones are disproportionately abundant because of their short lifespan. The current global production of E-waste is estimated to be 20-25 million tonnes per year, with most E-waste being produced in Europe, the United States and Australasia. China, Eastern Europe and Latin America will become major E-waste producers in the next ten years. Miniaturisation and the development of more efficient cloud computing networks, where computing services are delivered over the internet from remote locations, may offset the increase in E-waste production from global economic growth and the development of pervasive new technologies. E-waste contains valuable metals (Cu, platinum group) as well as potential environmental contaminants, especially Pb, Sb, Hg, Cd, Ni, polybrominated diphenyl ethers (PBDEs), and polychlorinated biphenyls (PCBs). Burning E-waste may generate dioxins, furans, polycyclic aromatic hydrocarbons (PAHs), polyhalogenated aromatic hydrocarbons (PHAHs), and hydrogen chloride. The chemical composition of E-waste changes with the development of new technologies and pressure from environmental organisations on electronics companies to find alternatives to environmentally damaging materials. Most E-waste is disposed in landfills. Effective reprocessing technology, which recovers the valuable materials with minimal environmental impact, is expensive. Consequently, although illegal under the Basel Convention, rich countries export an unknown quantity of E-waste to poor countries, where recycling techniques include burning and dissolution in strong acids with few measures to protect human health and the environment. Such reprocessing initially results in extreme localised contamination followed by migration of the contaminants into receiving waters and food chains. E-waste workers suffer negative health effects through skin contact and inhalation, while the wider community are exposed

Waste Heat Recovery from High Temperature Off-Gases from Electric Arc Furnace

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nimbalkar, Sachin U; Thekdi, Arvind; Keiser, James R

2014-01-01

This article presents a study and review of available waste heat in high temperature Electric Arc Furnace (EAF) off gases and heat recovery techniques/methods from these gases. It gives details of the quality and quantity of the sensible and chemical waste heat in typical EAF off gases, energy savings potential by recovering part of this heat, a comprehensive review of currently used waste heat recovery methods and potential for use of advanced designs to achieve a much higher level of heat recovery including scrap preheating, steam production and electric power generation. Based on our preliminary analysis, currently, for all electricmore » arc furnaces used in the US steel industry, the energy savings potential is equivalent to approximately 31 trillion Btu per year or 32.7 peta Joules per year (approximately $182 million US dollars/year). This article describes the EAF off-gas enthalpy model developed at Oak Ridge National Laboratory (ORNL) to calculate available and recoverable heat energy for a given stream of exhaust gases coming out of one or multiple EAF furnaces. This Excel based model calculates sensible and chemical enthalpy of the EAF off-gases during tap to tap time accounting for variation in quantity and quality of off gases. The model can be used to estimate energy saved through scrap preheating and other possible uses such as steam generation and electric power generation using off gas waste heat. This article includes a review of the historical development of existing waste heat recovery methods, their operations, and advantages/limitations of these methods. This paper also describes a program to develop and test advanced concepts for scrap preheating, steam production and electricity generation through use of waste heat recovery from the chemical and sensible heat contained in the EAF off gases with addition of minimum amount of dilution or cooling air upstream of pollution control equipment such as bag houses.« less

Reclamation of skid roads with fiber mats and native vegetation: effects on erosion

Treesearch

shawn T. Grushecky; David w. McGill; William Grafton; John Edwards; Lisa Tager

2007-01-01

A research study was established to test the effectiveness of fiber mats and native seed mixtures in reducing soil erosion from newly-constructed skid roads in the Elk River Watershed in central West Virginia. Twelve road sections of equal grade were paired with a randomly-selected section receiving a fiber mat and native grass seed while the other road section was not...

Designing and examining e-waste recycling process: methodology and case studies.

PubMed

Li, Jinhui; He, Xin; Zeng, Xianlai

2017-03-01

Increasing concerns on resource depletion and environmental pollution have largely obliged electrical and electronic waste (e-waste) should be tackled in an environmentally sound manner. Recycling process development is regarded as the most effective and fundamental to solve the e-waste problem. Based on global achievements related to e-waste recycling in the past 15 years, we first propose a theory to design an e-waste recycling process, including measuring e-waste recyclability and selection of recycling process. And we summarize the indicators and tools in terms of resource dimension, environmental dimension, and economic dimension, to examine the e-waste recycling process. Using the sophisticated experience and adequate information of e-waste management, spent lithium-ion batteries and waste printed circuit boards are chosen as case studies to implement and verify the proposed method. All the potential theory and obtained results in this work can contribute to future e-waste management toward best available techniques and best environmental practices.

Recycling and processing of several typical crosslinked polymer scraps with enhanced mechanical properties based on solid-state mechanochemical milling

NASA Astrophysics Data System (ADS)

Lu, Canhui; Zhang, Xinxing; Zhang, Wei

2015-05-01

The partially devulcanization or de-crosslinking of ground tire rubber (GTR), post-vulcanized fluororubber scraps and crosslinked polyethylene from cable scraps through high-shear mechanochemical milling (HSMM) was conducted by a modified solid-state mechanochemical reactor. The results indicated that the HSMM treated crosslinked polymer scraps can be reprocessed as virgin rubbers or thermoplastics to produce materials with high performance. The foamed composites of low density polyethylene/GTR and the blend of post-vulcanized flurorubber (FKM) with polyacrylate rubber (ACM) with better processability and mechanical properties were obtained. The morphology observation showed that the dispersion and compatibility between de-crosslinked polymer scraps and matrix were enhanced. The results demonstrated that HSMM is a feasible alternative technology for recycling post-vulcanized or crosslinked polymer scraps.

40 CFR 63.10885 - What are my management practices for metallic scrap and mercury switches?

Code of Federal Regulations, 2010 CFR

2010-07-01

... metallic scrap and mercury switches? 63.10885 Section 63.10885 Protection of Environment ENVIRONMENTAL... Iron and Steel Foundries Area Sources Pollution Prevention Management Practices for New and Existing Affected Sources § 63.10885 What are my management practices for metallic scrap and mercury switches? (a...

40 CFR 63.10885 - What are my management practices for metallic scrap and mercury switches?

Code of Federal Regulations, 2011 CFR

2011-07-01

... metallic scrap and mercury switches? 63.10885 Section 63.10885 Protection of Environment ENVIRONMENTAL... Iron and Steel Foundries Area Sources Pollution Prevention Management Practices for New and Existing Affected Sources § 63.10885 What are my management practices for metallic scrap and mercury switches? (a...

Green technology for conversion of food scraps to biodegradable thermoplastic polyhydroxyalkanoates.

PubMed

Du, Guocheng; Yu, Jian

2002-12-15

A new technology is developed and demonstrated that couples anaerobic digestion of food scraps with production of biodegradable thermoplastics, polyhydroxyalkanoates (PHAs). The food wastes were digested in an anaerobic reactor producing four major organic acids. The concentrations of acetic, propionic, butyric, and lactic acids reached 5.5, 1.8, 27.4, and 32.7 g/L, respectively. The fermentative acids were transferred through membranes via molecule diffusion into an air-bubbling reactor where the acids were utilized to produce PHAs in an enriched culture of Ralstonia eutropha. With a silicone rubber membrane, butyric acid and small amounts of acetic and propionic acids were transferred and used, producing a homopolymer PHA, poly(3-hydroxybutyrate). The dry cell weight and PHA content reached 11.3 g/L and 60.2% (w/w), respectively. With a dialysis membrane, the mass transfer rates of fermentative acids were enhanced, and the PHA production was significantly improved. The dry cell weight and its PHA content reached 22.7 g/L and 72.6% (w/w), respectively. The formed PHA was a copolymer of 3-hydroxybutyrate and 3-hydroxyvalerate (HV) with 2.8 mol % HV monomer unit. The polymer content (72.6% of dry cell mass) reported in this study is the highest one obtained from organic wastes and is comparable with the PHA content from pure glucose fermentation.

40 CFR 63.10685 - What are the requirements for the control of contaminants from scrap?

Code of Federal Regulations, 2013 CFR

2013-07-01

... not charge to a furnace metallic scrap that contains scrap from motor vehicle bodies, engine blocks... vehicle bodies, engine blocks, oil filters, oily turnings, machine shop borings, transformers or... restriction does not apply to any post-consumer engine blocks, post-consumer oil filters, or oily turnings...

40 CFR 63.10685 - What are the requirements for the control of contaminants from scrap?

Code of Federal Regulations, 2012 CFR

2012-07-01

... not charge to a furnace metallic scrap that contains scrap from motor vehicle bodies, engine blocks... vehicle bodies, engine blocks, oil filters, oily turnings, machine shop borings, transformers or... restriction does not apply to any post-consumer engine blocks, post-consumer oil filters, or oily turnings...

40 CFR 63.10685 - What are the requirements for the control of contaminants from scrap?

Code of Federal Regulations, 2014 CFR

2014-07-01

... not charge to a furnace metallic scrap that contains scrap from motor vehicle bodies, engine blocks... vehicle bodies, engine blocks, oil filters, oily turnings, machine shop borings, transformers or... restriction does not apply to any post-consumer engine blocks, post-consumer oil filters, or oily turnings...

Aeromagnetic investigations of hazardous waste sites

USGS Publications Warehouse

,

1995-01-01

Aeromagnetic survey data collected by helicopter over hazardous waste sites can be used to map the distribution of buried metallic (ferrous) objects at these sites, including drums and scrap metal. Thorough knowledge of the locations and nature of hazardous waste containers and contaminated objects is needed prior to the start of remediation efforts. Non-invasive geophysical techniques such as the aeromagnetic method provide the best way to obtain this knowledge. The U.S. Geological Survey (USGS) not only has experience in processing and interpreting aeromagnetic surveys of this type but also offers aid in the design and monitoring of contracts for such surveys.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finster, Molly E; Raymond, Michelle R.; Scofield, Marcienne A.

The reuse and recycling of industrial solid wastes such as scrap metal is supported and encouraged both internationally and domestically, especially when such wastes can be used as substitutes for raw material. However, scrap metal processing facilities, such as mini-mills, have been identified as a source of mercury (Hg) emissions in the United States. This research aims to better define some of the key issues related to the source and nature of mercury in the scrap metal waste stream. Overall, it is difficult to pinpoint the key mercury sources feeding into scrap metal recycling facilities, quantify their associated mercury concentrations,more » or determine which chemical forms are most significant. Potential sources of mercury in scrap metal include mercury switches from discarded vehicles, electronic-based scrap from household appliances and related industrial systems, and Hg-impacted scrap metal from the oil and gas industry. The form of mercury associated with scrap metal varies and depends on the source type. The specific amount of mercury that can be adsorbed and retained by steel appears to be a function of both metallurgical and environmental factors. In general, the longer the steel is in contact with a fluid or condensate that contains measurable concentrations of elemental mercury, the greater the potential for mercury accumulation in that steel. Most mercury compounds are thermally unstable at elevated temperatures (i.e., above 350°C). As such, the mercury associated with impacted scrap is expected to be volatilized out of the metal when it is heated during processing (e.g., shredding or torch cutting) or melted in a furnace. This release of fugitive gas (Hg vapor) and particulates, as well as Hg-impacted bag-house dust and control filters, could potentially pose an occupational exposure risk to workers at a scrap metal processing facility. Thus, identifying and characterizing the key sources of Hg-impacted scrap, and understanding the nature and

Recycling and processing of several typical crosslinked polymer scraps with enhanced mechanical properties based on solid-state mechanochemical milling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Canhui; Zhang, Xinxing; Zhang, Wei

The partially devulcanization or de-crosslinking of ground tire rubber (GTR), post-vulcanized fluororubber scraps and crosslinked polyethylene from cable scraps through high-shear mechanochemical milling (HSMM) was conducted by a modified solid-state mechanochemical reactor. The results indicated that the HSMM treated crosslinked polymer scraps can be reprocessed as virgin rubbers or thermoplastics to produce materials with high performance. The foamed composites of low density polyethylene/GTR and the blend of post-vulcanized flurorubber (FKM) with polyacrylate rubber (ACM) with better processability and mechanical properties were obtained. The morphology observation showed that the dispersion and compatibility between de-crosslinked polymer scraps and matrix were enhanced. Themore » results demonstrated that HSMM is a feasible alternative technology for recycling post-vulcanized or crosslinked polymer scraps.« less

Characterization of the High-Speed-Stage Bearing Skidding of Wind Turbine Gearboxes Induced by Dynamic Electricity Grid Events: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helsen, Jan; Guillaume, Patrick; Guo, Yi

Bearing behavior is an important factor for wind turbine drivetrain reliability. Extreme loads and dynamic excitations pose challenges to the bearing design and therefore its performance. Excessive skidding of the bearing rollers should be avoided because it can cause scuffing failures. Excitations coming from wind and the electricity grid can subject the drivetrain to fluctuating torque and nontorque loads. Wind-induced excitations have been investigated predominantly in literature. However, modern wind turbines are subjected more and more to grid-induced loads because of stricter electricity grid regulations. For example, during fault-ride-through events, turbines are required to stay connected for a longer periodmore » of time during the grid failure. This work investigates the influence of electrically induced excitations on the skidding behaviour of the tapered roller bearings on the high-speed stage of a wind turbine gearbox. This skidding behaviour during dynamic events is described as a potential bearing failure initiator by many researchers; however, only limited full-scale dynamic testing is documented. Therefore, a dedicated gridloss-type event is defined in the paper and conducted in a dynamometer test on a full-scale wind turbine nacelle. During the event, a complete electricity grid failure is simulated while the turbine is at rated speed and predefined torque levels. Particular focus is on the characterization of the high-speed shaft tapered roller bearing slip behavior. Strain-gauge bridges in grooves along the circumference of the outer ring are used to characterize the bearing load zone in detail. It is shown that during the torque reversals of the transient event, roller slip can be induced. This indicates the potential of the applied load case to go beyond the preload of the tapered roller bearing. Furthermore, the relation between the applied torque and skidding level is studied.« less

Effect of aggregate graining compositions on skid resistance of Exposed Aggregate Concrete pavement

NASA Astrophysics Data System (ADS)

Wasilewska, Marta; Gardziejczyk, Wladysław; Gierasimiuk, Pawel

2018-05-01

The paper presents the evaluation of skid resistance of EAC (Exposed Aggregate Concrete) pavements which differ in aggregate graining compositions. The tests were carried out on concrete mixes with a maximum aggregate size of 8 mm. Three types of coarse aggregates were selected depending on their resistance to polishing which was determined on the basis of the PSV (Polished Stone Value). Basalt (PSV 48), gabbro (PSV 50) and trachybasalt (PSV 52) aggregates were chosen. For each type of aggregate three graining compositions were designed, which differed in the content of coarse aggregate > 4mm. Their content for each series was as follows: A - 38%, B - 50% and C - 68%. Evaluation of the skid resistance has been performed using the FAP (Friction After Polishing) test equipment also known as the Wehner/Schulze machine. Laboratory method enables to compare the skid resistance of different types of wearing course under specified conditions simulating polishing processes. In addition, macrotexture measurements were made on the surface of each specimen using the Elatexure laser profile. Analysis of variance showed that at significance level α = 0.05, aggregate graining compositions as well as the PSV have a significant influence on the obtained values of the friction coefficient μm of the tested EAC pavements. The highest values of the μm have been obtained for EAC with the lowest amount of coarse aggregates (compositions A). In these cases the resistance to polishing of the aggregate does not significantly affect the friction coefficients. This is related to the large areas of cement mortar between the exposed coarse grains. Based on the analysis of microscope images, it was observed that the coarse aggregates were not sufficiently exposed. It has been proved that PSV significantly affected the coefficient of friction in the case of compositions B and C. This is caused by large areas of exposed coarse aggregate. The best parameters were achieved for the EAC pavements

Estimation of future outflows of e-waste in India.

PubMed

Dwivedy, Maheshwar; Mittal, R K

2010-03-01

The purpose of this study is to construct an approach and a methodology to estimate the future outflows of electronic waste (e-waste) in India. Consequently, the study utilizes a time-series multiple lifespan end-of-life model proposed by Peralta and Fontanos for estimating the current and future quantities of e-waste in India. The model estimates future e-waste generation quantities by modeling their usage and disposal. The present work considers two scenarios for the approximation of e-waste generation based on user preferences to store or to recycle the e-waste. This model will help formal recyclers in India to make strategic decisions in planning for appropriate recycling infrastructure and institutional capacity building. Also an extension of the model proposed by Peralta and Fontanos is developed with the objective of helping decision makers to conduct WEEE estimates under a variety of assumptions to suit their region of study. During 2007-2011, the total WEEE estimates will be around 2.5 million metric tons which include waste from personal computers (PC), television, refrigerators and washing machines. During the said period, the waste from PC will account for 30% of total units of WEEE generated. Copyright 2009 Elsevier Ltd. All rights reserved.

Estimation of future outflows of e-waste in India

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dwivedy, Maheshwar, E-mail: dwivedy_m@bits-pilani.ac.i; Mittal, R.K.

2010-03-15

The purpose of this study is to construct an approach and a methodology to estimate the future outflows of electronic waste (e-waste) in India. Consequently, the study utilizes a time-series multiple lifespan end-of-life model proposed by Peralta and Fontanos for estimating the current and future quantities of e-waste in India. The model estimates future e-waste generation quantities by modeling their usage and disposal. The present work considers two scenarios for the approximation of e-waste generation based on user preferences to store or to recycle the e-waste. This model will help formal recyclers in India to make strategic decisions in planningmore » for appropriate recycling infrastructure and institutional capacity building. Also an extension of the model proposed by Peralta and Fontanos is developed with the objective of helping decision makers to conduct WEEE estimates under a variety of assumptions to suit their region of study. During 2007-2011, the total WEEE estimates will be around 2.5 million metric tons which include waste from personal computers (PC), television, refrigerators and washing machines. During the said period, the waste from PC will account for 30% of total units of WEEE generated.« less

The Scrap Tire Problem: A Preliminary Economic Analysis (1985)

EPA Pesticide Factsheets

The purpose of the study was to conduct a preliminary economic analysis of the social benefits of EPA action to require more appropriate disposal of scrap tires versus the social costs of such an action.

Reconstituted Polymeric Materials Derived From Post-Consumer Waste, Industrial Scrap And Virgin Resins Made By Solid State Shear Pulverizat

DOEpatents

Khait, Klementina

2005-02-01

A method of making polymeric particulates wherein polymeric scrap material, virgin polymeric material and mixtures thereof are supplied to intermeshing extruder screws which are rotated to transport the polymeric material along their length and subject the polymeric material to solid state shear pulverization and in-situ polymer compatibilization, if two or more incompatible polymers are present. Uniform pulverized particulates are produced without addition of a compatibilizing agent. The pulverized particulates are directly melt processable (as powder feedstock) and surprisingly yield a substantially homogeneous light color product.

Reconstituted polymeric materials derived from post-consumer waste, industrial scrap and virgin resins made by solid state shear pulverization

DOEpatents

Khait, Klementina

2001-01-30

A method of making polymeric particulates wherein polymeric scrap material, virgin polymeric material and mixtures thereof are supplied to intermeshing extruder screws which are rotated to transport the polymeric material along their length and subject the polymeric material to solid state shear pulverization and in-situ polymer compatibilization, if two or more incompatible polymers are present. Uniform pulverized particulates are produced without addition of a compatibilizing agent. The pulverized particulates are directly melt processable (as powder feedstock) and surprisingly yield a substantially homogeneous light color product.

32 CFR 644.522 - Clearance of military scrap.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Clearance of military scrap. 644.522 Section 644.522 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from Proposed...

Application of activated carbon derived from scrap tires for adsorption of Rhodamine B.

PubMed

Li, Li; Liu, Shuangxi; Zhu, Tan

2010-01-01

Activated carbon derived from solid hazardous waste scrap tires was evaluated as a potential adsorbent for cationic dye removal. The adsorption process with respect to operating parameters was investigated to evaluate the adsorption characteristics of the activated pyrolytic tire char (APTC) for Rhodamine B (RhB). Systematic research including equilibrium, kinetics and thermodynamic studies was performed. The results showed that APTC was a potential adsorbent for RhB with a higher adsorption capacity than most adsorbents. Solution pH and temperature exert significant influence while ionic strength showed little effect on the adsorption process. The adsorption equilibrium data obey Langmuir isotherm and the kinetic data were well described by the pseudo second-order kinetic model. The adsorption process followed intra-particle diffusion model with more than one process affecting the adsorption process. Thermodynamic study confirmed that the adsorption was a physisorption process with spontaneous, endothermic and random characteristics.

Multiple Elemental Exposures Amongst Workers at the Agbogbloshie Electronic Waste (E-Waste) Site in Ghana

PubMed Central

Srigboh, Roland Kofi; Basu, Niladri; Stephens, Judith; Asampong, Emmanuel; Perkins, Marie; Neitzel, Richard L.; Fobil, Julius

2016-01-01

Electronic waste (e-waste) recycling is growing worldwide and raising a number of environmental health concerns. One of the largest e-waste sites is Agbogbloshie (Ghana). While several toxic elements have been reported in Agbogbloshie’s environment, there is limited knowledge of human exposures there. The objectives of this study were to characterize exposures to several essential (copper, iron, manganese, selenium, zinc) and toxic (arsenic, cadmium, cobalt, chromium, mercury, nickel, lead) elements in the urine and blood of male workers (n=58) at Agbogbloshie, as well as females (n=11) working in activities that serve the site, and to relate these exposures to sociodemographic and occupational characteristics. The median number of years worked at the site was 5, and the average worker indicated being active in 6.8 tasks (of 9 key e-waste job categories). Additionally, we categorized four main e-waste activities (in brackets % of population self-reported main activity): dealing (22.4%), sorting (24.1%), dismantling (50%), and burning (3.4%) e-waste materials. Many blood and urinary elements (including essential ones) were within biomonitoring reference ranges. However, blood cadmium (1.2 ug/L median) and lead (6.4 ug/dl; 67% above U.S. CDC/NIOSH reference level), and urinary arsenic (38.3 ug/L; 39% above U.S. ATSDR value) levels were elevated compared to background populations elsewhere. Workers who burned e-waste tended to have the highest biomarker levels. The findings of this study contribute to a growing body of work at Agbogbloshie (and elsewhere) to document that individuals working within e-waste sites are exposed to a number of toxic elements, some at potentially concerning levels. PMID:27580259

Productivity and cost of manual felling and cable skidding in central Appalachian hardwood forests

Treesearch

Jingxin Wang; Charlie Long; Joe McNeel; John Baumgras; John Baumgras

2004-01-01

A field production study was conducted for a manual harvesting system using a chainsaw and cable skidder in a central Appalachian hardwood forest site. A partial cut was performed on a 50-acre tract with an average slope of 25 percent. Felling time pre tree was most affected by diameter at breast height and the distance between harvested trees while skidding cycle time...

Effective regeneration of anode material recycled from scrapped Li-ion batteries

NASA Astrophysics Data System (ADS)

Zhang, Jin; Li, Xuelei; Song, Dawei; Miao, Yanli; Song, Jishun; Zhang, Lianqi

2018-06-01

Recycling high-valuable metal elements (such as Li, Ni, Co, Al and Cu elements) from scrapped lithium ion batteries can bring significant economic benefits. However, recycling and reusing anode material has not yet attracted wide attention up to now, due to the lower added-value than the above valuable metal materials and the difficulties in regenerating process. In this paper, a novel regeneration process with significant green advance is proposed to regenerate anode material recycled from scrapped Li-ion batteries for the first time. After regenerated, most acetylene black (AB) and all the styrene butadiene rubber (SBR), carboxymethylcellulose sodium (CMC) in recycled anode material are removed, and the surface of anode material is coated with pyrolytic carbon from phenolic resin again. Finally, the regenerated anode material (graphite with coating layer, residual AB and a little CMC pyrolysis product) is obtained. As expected, all the technical indexs of regenerated anode material exceed that of a midrange graphite with the same type, and partial technical indexs are even closed to that of the unused graphite. The results indicate the effective regeneration of anode material recycled from scrapped Li-ion batteries is really achieved.

Where next on e-waste in Australia?

PubMed

Golev, Artem; Schmeda-Lopez, Diego R; Smart, Simon K; Corder, Glen D; McFarland, Eric W

2016-12-01

For almost two decades waste electrical and electronic equipment, WEEE or e-waste, has been considered a growing problem that has global consequences. The value of recovered materials, primarily in precious and base metals, has prompted some parts of the world to informally and inappropriately process e-waste causing serious environmental and human health issues. Efforts in tackling this issue have been limited and in many ways unsuccessful. The global rates for formal e-waste treatment are estimated to be below the 20% mark, with the majority of end-of-life (EoL) electronic devices still ending up in the landfills or processed through rudimentary means. Industrial confidentiality regarding device composition combined with insufficient reporting requirements has made the task of simply characterizing the problem difficult at a global scale. To address some of these key issues, this paper presents a critical overview of existing statistics and estimations for e-waste in an Australia context, including potential value and environmental risks associated with metals recovery. From our findings, in 2014, on average per person, Australians purchased 35kg of electrical and electronic equipment (EEE) while disposed of 25kg of WEEE, and possessed approximately 320kg of EEE. The total amount of WEEE was estimated at 587kt worth about US$ 370million if all major metals are fully recovered. These results are presented over the period 2010-2014, detailed for major EEE product categories and metals, and followed by 2015-2024 forecast. Our future projection, with the base scenario fixing EEE sales at 35kg per capita, predicts stabilization of e-waste generation in Australia at 28-29kg per capita, with the total amount continuing to grow along with the population growth. Copyright © 2016 Elsevier Ltd. All rights reserved.

E-waste disposal effects on the aquatic environment: Accra, Ghana.

PubMed

Huang, Jingyu; Nkrumah, Philip Nti; Anim, Desmond Ofosu; Mensah, Ebenezer

2014-01-01

The volume of e-waste is growing around the world, and, increasingly, it is being disposed of by export from developed to developing countries. This is the situation in Ghana, and, in this paper we address the potential consequences of such e-waste disposal. Herein, we describe how e-waste is processed in Ghana, and what the fate is of e-waste-chemical contaminants during recycling and storage. Finally, to the extent it is known, we address the prospective adverse effects of e-waste-related contaminants on health and aquatic life downstream from a large e-waste disposal facility in Accra, Ghana.In developing countries, including Ghana, e-waste is routinely disassembled by unprotected workers that utilize rudimentary methods and tools. Once disassembled,e-waste components are often stored in large piles outdoors. These processing and storage methods expose workers and local residents to several heavy metals and organic chemicals that exist in e-waste components. The amount of e-waste dumped in Ghana is increasing annually by about 20,000 t. The local aquatic environment is at a potential high risk, because the piles of e-waste components stored outside are routinely drenched or flooded by rainfall, producing run-off from storage sites to local waterways. Both water and sediment samples show that e-waste-related contaminant shave entered Ghana's water ways.The extent of pollution produced in key water bodies of Ghana (Odaw River and the Korle Lagoon) underscores the need for aquatic risk assessments of the many contaminants released during e-waste processing. Notwithstanding the fact that pollutants from other sources reach the water bodies, it is clear that these water bodies are also heavily impacted by contaminants that are found in e-waste. Our concern is that such exposures have limited and will continue to limit the diversity of aquatic organisms.There have also been changes in the abundance and biomass of surviving species and changes in food chains. Therefore

Thermodynamic Analysis on of Skid-Mounted Coal-bed Methane Liquefaction Device using Cryogenic Turbo-Expander

NASA Astrophysics Data System (ADS)

Chen, Shuangtao; Niu, Lu; Zeng, Qiang; Li, Xiaojiang; Lou, Fang; Chen, Liang; Hou, Yu

2017-12-01

Coal-bed methane (CBM) reserves are rich in Sinkiang of China, and liquefaction is a critical step for the CBM exploration and utilization. Different from other CBM gas fields in China, CBM distribution in Sinkiang is widespread but scattered, and the pressure, flow-rate and nitrogen content of CBM feed vary significantly. The skid-mounted liquefaction device is suggested as an efficient and economical way to recover methane. Turbo-expander is one of the most important parts which generates the cooling capacity for the cryogenic liquefaction system. Using turbo-expander, more cooling capacity and higher liquefied fraction can be achieved. In this study, skid-mounted CBM liquefaction processes based on Claude cycle are established. Cryogenic turbo-expander with high expansion ratio is employed to improve the efficiency of CBM liquefaction process. The unit power consumption per liquefaction mole flow-rate for CBM feed gas is used as the object function for process optimization, compressor discharge pressure, flow ratio of feed gas to turbo-expander and nitrogen friction are analyzed, and optimum operation range of the liquefaction processes are obtained.

Halfthrough girder over entrance to scrap yard at western end ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Half-through girder over entrance to scrap yard at western end of trestle, looking NW. - Pennsylvania Railroad, French Creek Trestle, Spanning French Creek, north of Paradise Street, Phoenixville, Chester County, PA

E-Waste and Harm to Vulnerable Populations: A Growing Global Problem

PubMed Central

Heacock, Michelle; Kelly, Carol Bain; Asante, Kwadwo Ansong; Birnbaum, Linda S.; Bergman, Åke Lennart; Bruné, Marie-Noel; Buka, Irena; Carpenter, David O.; Chen, Aimin; Huo, Xia; Kamel, Mostafa; Landrigan, Philip J.; Magalini, Federico; Diaz-Barriga, Fernando; Neira, Maria; Omar, Magdy; Pascale, Antonio; Ruchirawat, Mathuros; Sly, Leith; Sly, Peter D.; Van den Berg, Martin; Suk, William A.

2015-01-01

Background: Electronic waste (e-waste) is produced in staggering quantities, estimated globally to be 41.8 million tonnes in 2014. Informal e-waste recycling is a source of much-needed income in many low- to middle-income countries. However, its handling and disposal in underdeveloped countries is often unsafe and leads to contaminated environments. Rudimentary and uncontrolled processing methods often result in substantial harmful chemical exposures among vulnerable populations, including women and children. E-waste hazards have not yet received the attention they deserve in research and public health agendas. Objectives: We provide an overview of the scale and health risks. We review international efforts concerned with environmental hazards, especially affecting children, as a preface to presenting next steps in addressing health issues stemming from the global e-waste problem. Discussion: The e-waste problem has been building for decades. Increased observation of adverse health effects from e-waste sites calls for protecting human health and the environment from e-waste contamination. Even if e-waste exposure intervention and prevention efforts are implemented, legacy contamination will remain, necessitating increased awareness of e-waste as a major environmental health threat. Conclusion: Global, national, and local levels efforts must aim to create safe recycling operations that consider broad security issues for people who rely on e-waste processing for survival. Paramount to these efforts is reducing pregnant women and children’s e-waste exposures to mitigate harmful health effects. With human environmental health in mind, novel dismantling methods and remediation technologies and intervention practices are needed to protect communities. Citation: Heacock M, Kelly CB, Asante KA, Birnbaum LS, Bergman AL, Bruné MN, Buka I, Carpenter DO, Chen A, Huo X, Kamel M, Landrigan PJ, Magalini F, Diaz-Barriga F, Neira M, Omar M, Pascale A, Ruchirawat M, Sly L, Sly PD

E-Waste and Harm to Vulnerable Populations: A Growing Global Problem.

PubMed

Heacock, Michelle; Kelly, Carol Bain; Asante, Kwadwo Ansong; Birnbaum, Linda S; Bergman, Åke Lennart; Bruné, Marie-Noel; Buka, Irena; Carpenter, David O; Chen, Aimin; Huo, Xia; Kamel, Mostafa; Landrigan, Philip J; Magalini, Federico; Diaz-Barriga, Fernando; Neira, Maria; Omar, Magdy; Pascale, Antonio; Ruchirawat, Mathuros; Sly, Leith; Sly, Peter D; Van den Berg, Martin; Suk, William A

2016-05-01

Electronic waste (e-waste) is produced in staggering quantities, estimated globally to be 41.8 million tonnes in 2014. Informal e-waste recycling is a source of much-needed income in many low- to middle-income countries. However, its handling and disposal in underdeveloped countries is often unsafe and leads to contaminated environments. Rudimentary and uncontrolled processing methods often result in substantial harmful chemical exposures among vulnerable populations, including women and children. E-waste hazards have not yet received the attention they deserve in research and public health agendas. We provide an overview of the scale and health risks. We review international efforts concerned with environmental hazards, especially affecting children, as a preface to presenting next steps in addressing health issues stemming from the global e-waste problem. The e-waste problem has been building for decades. Increased observation of adverse health effects from e-waste sites calls for protecting human health and the environment from e-waste contamination. Even if e-waste exposure intervention and prevention efforts are implemented, legacy contamination will remain, necessitating increased awareness of e-waste as a major environmental health threat. Global, national, and local levels efforts must aim to create safe recycling operations that consider broad security issues for people who rely on e-waste processing for survival. Paramount to these efforts is reducing pregnant women and children's e-waste exposures to mitigate harmful health effects. With human environmental health in mind, novel dismantling methods and remediation technologies and intervention practices are needed to protect communities. Heacock M, Kelly CB, Asante KA, Birnbaum LS, Bergman AL, Bruné MN, Buka I, Carpenter DO, Chen A, Huo X, Kamel M, Landrigan PJ, Magalini F, Diaz-Barriga F, Neira M, Omar M, Pascale A, Ruchirawat M, Sly L, Sly PD, Van den Berg M, Suk WA. 2016. E-waste and harm to

Multiple elemental exposures amongst workers at the Agbogbloshie electronic waste (e-waste) site in Ghana.

PubMed

Srigboh, Roland Kofi; Basu, Niladri; Stephens, Judith; Asampong, Emmanuel; Perkins, Marie; Neitzel, Richard L; Fobil, Julius

2016-12-01

Electronic waste (e-waste) recycling is growing worldwide and raising a number of environmental health concerns. One of the largest e-waste sites is Agbogbloshie (Ghana). While several toxic elements have been reported in Agbogbloshie's environment, there is limited knowledge of human exposures there. The objectives of this study were to characterize exposures to several essential (copper, iron, manganese, selenium, zinc) and toxic (arsenic, cadmium, cobalt, chromium, mercury, nickel, lead) elements in the urine and blood of male workers (n = 58) at Agbogbloshie, as well as females (n = 11) working in activities that serve the site, and to relate these exposures to sociodemographic and occupational characteristics. The median number of years worked at the site was 5, and the average worker indicated being active in 6.8 tasks (of 9 key e-waste job categories). Additionally, we categorized four main e-waste activities (in brackets % of population self-reported main activity): dealing (22.4%), sorting (24.1%), dismantling (50%), and burning (3.4%) e-waste materials. Many blood and urinary elements (including essential ones) were within biomonitoring reference ranges. However, blood cadmium (1.2 μg/L median) and lead (6.4 μg/dl; 67% above U.S. CDC/NIOSH reference level), and urinary arsenic (38.3 μg/L; 39% above U.S. ATSDR value) levels were elevated compared to background populations elsewhere. Workers who burned e-waste tended to have the highest biomarker levels. The findings of this study contribute to a growing body of work at Agbogbloshie (and elsewhere) to document that individuals working within e-waste sites are exposed to a number of toxic elements, some at potentially concerning levels. Copyright © 2016 Elsevier Ltd. All rights reserved.

Astronauts greet the U.S. Women's World Cup Soccer Team at the Skid Strip

NASA Technical Reports Server (NTRS)

1999-01-01

Members of the U.S. Women's World Cup Soccer Team were greeted upon their arrival at the Skid Strip at Cape Canaveral Air Station by Astronauts (right) Steven W. Lindsey, Heidemarie M. Stefanyshyn-Piper and Scott E. Parzynski. The team are here to view the launch of Space Shuttle mission STS-93, scheduled for 12:36 a.m. EDT July 20. Much attention has been generated over the launch due to Commander Eileen M. Collins, the first woman to serve as commander of a Shuttle mission. The primary payload of the five-day mission is the Chandra X-ray Observatory, which will allow scientists from around the world to study some of the most distant, powerful and dynamic objects in the universe. The new telescope is 20 to 50 times more sensitive than any previous X- ray telescope and is expected to unlock the secrets of supernovae, quasars and black holes.

E-waste Management and Refurbishment Prediction (EMARP) Model for Refurbishment Industries.

PubMed

Resmi, N G; Fasila, K A

2017-10-01

This paper proposes a novel algorithm for establishing a standard methodology to manage and refurbish e-waste called E-waste Management And Refurbishment Prediction (EMARP), which can be adapted by refurbishing industries in order to improve their performance. Waste management, particularly, e-waste management is a serious issue nowadays. Computerization has been into waste management in different ways. Much of the computerization has happened in planning the waste collection, recycling and disposal process and also managing documents and reports related to waste management. This paper proposes a computerized model to make predictions for e-waste refurbishment. All possibilities for reusing the common components among the collected e-waste samples are predicted, thus minimizing the wastage. Simulation of the model has been done to analyse the accuracy in the predictions made by the system. The model can be scaled to accommodate the real-world scenario. Copyright © 2017 Elsevier Ltd. All rights reserved.

Developmental neurotoxicants in e-waste: an emerging health concern.

PubMed

Chen, Aimin; Dietrich, Kim N; Huo, Xia; Ho, Shuk-mei

2011-04-01

Electronic waste (e-waste) has been an emerging environmental health issue in both developed and developing countries, but its current management practice may result in unintended developmental neurotoxicity in vulnerable populations. To provide updated information about the scope of the issue, presence of known and suspected neurotoxicants, toxicologic mechanisms, and current data gaps, we conducted this literature review. We reviewed original articles and review papers in PubMed and Web of Science regarding e-waste toxicants and their potential developmental neurotoxicity. We also searched published reports of intergovernmental and governmental agencies and nongovernmental organizations on e-waste production and management practice. We focused on the potential exposure to e-waste toxicants in vulnerable populations-that is, pregnant women and developing children-and neurodevelopmental outcomes. In addition, we summarize experimental evidence of developmental neurotoxicity and mechanisms. In developing countries where most informal and primitive e-waste recycling occurs, environmental exposure to lead, cadmium, chromium, polybrominated diphenyl ethers, polychlorinated biphenyls, and polycyclic aromatic hydrocarbons is prevalent at high concentrations in pregnant women and young children. Developmental neurotoxicity is a serious concern in these regions, but human studies of adverse effects and potential mechanisms are scarce. The unprecedented mixture of exposure to heavy metals and persistent organic pollutants warrants further studies and necessitates effective pollution control measures. Pregnant women and young children living close to informal e-waste recycling sites are at risk of possible perturbations of fetus and child neurodevelopment.

Unfair trade: e-waste in Africa.

PubMed

Schmidt, Charles W

2006-04-01

Africa is quickly becoming a destination for information technology in the form of tons of used computers, fax machines, cell phones, and other electronics. Although many of these machines can be repaired and resold, up to 75% of the electronics shipped to Africa is junk. This equipment, when dumped, may leach lead, mercury, and cadmium into the environment; when burned, it may release carcinogenic dioxins and polyaromatic hydrocarbons. In the United States, activists are working to limit the flow of e-waste to developing countries through international agreements and voluntary e-waste export reduction efforts.

EFFECTOF ISOLATION WALL USING SCRAP TIRE ON GROUND VIBRATION REDUCTION

NASA Astrophysics Data System (ADS)

Kashimoto, Takahiko; Kashimoto, Yusuke; Hayakawa, Kiyoshi; Matsui, Tamotsu; Fujimoto, Hiroaki

Some countermeasure methods against the environmental ground vibration caused by some traffic vibrations have been proposed so far. The authors have developed a new type ground vibration isolation wall using scrap tire, and evaluated its effectiveness on the ground vibration reduction by full scale field tests. In this paper, the authors discussed and examined the effectiveness of the developed countermeasure method by two field tests. The one concerns on the effect of scrap tire as soft material of vibration isolation wall, and the other on the effect of the developed countermeasure method practically applied in a residential area close to monorail traffic. As the results, it was elucidated that the ground vibration of 2-3 dB was reduced in case of two times volume of the soft material, the conversion ratio of the vibration energy of the soft material to the kinetic energy was higher than that of the core material of PHC pile, the vibration acceleration of 0.19 - 1.26 gal was reduced by the developed countermeasure method in case of the monorail traffic, and the vibration reduction measured behind the isolation wall agreed well with the proposed theoretical value, together with confirming the effectiveness of the ground vibration isolation wall using scrap tire as the countermeasure method against the environmental ground vibration.

Use of Portal Monitors for Detection of Technogenic Radioactive Sources in Scrap Metal

NASA Astrophysics Data System (ADS)

Solovev, D. B.; Merkusheva, A. E.

2017-11-01

The article considers the features of organization of scrap-metal primary radiation control on the specialized enterprises engaging in its deep processing and storage at using by primary technical equipment - radiation portal monitors. The issue of this direction relevance, validity of radiation control implementation with the use of radiation portal monitors, physical and organizational bases of radiation control are considered in detail. The emphasis is put on the considerable increase in the number of technogenic radioactive sources detected in scrap-metal that results in the entering into exploitation of radioactive metallic structures as different building wares. One of reasons of such increase of the number of technogenic radioactive sources getting for processing with scrap-metal is the absence of any recommendations on the radiation portal monitors exploitation. The practical division of the article offers to recommendation on tuning of the modes of work of radiation portal monitors depending on influence the weather factor thus allowing to considerably increase the percent of technogenic radioactive sources detection.

Noneconomic factors influencing scrap metal disposition decisions at DOE and NRC-licensed nuclear facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ewen, M.D.; Robinson, L.A.

1997-02-01

The U.S. Environmental Protection Agency (EPA) is currently developing radiation protection standards for scrap metal, which will establish criteria for the unconditional clearance of scrap from nuclear facilities. In support of this effort, Industrial Economics, Incorporated is assessing the costs and benefits attributable to the rulemaking. The first step in this analysis is to develop an in-depth understanding of the factors influencing scrap disposition decisions, so that one can predict current and future practices under existing requirements and compare them to the potential effects of EPA`s rulemaking. These baseline practices are difficult to predict due to a variety of factors.more » First, because decommissioning activities are just beginning at many sites, current practices do not necessarily provide an accurate indicator of how these practices may evolve as site managers gain experience with related decisions. Second, a number of different regulations and policies apply to these decisions, and the interactive effects of these requirements can be difficult to predict. Third, factors other than regulatory constraints and costs may have a significant effect on related decisions, such as concerns about public perceptions. In general, research suggests that these factors tend to discourage the unconditional clearance of scrap metal.« less

Health consequences of exposure to e-waste: a systematic review.

PubMed

Grant, Kristen; Goldizen, Fiona C; Sly, Peter D; Brune, Marie-Noel; Neira, Maria; van den Berg, Martin; Norman, Rosana E

2013-12-01

The population exposed to potentially hazardous substances through inappropriate and unsafe management practices related to disposal and recycling of end-of-life electrical and electronic equipment, collectively known as e-waste, is increasing. We aimed to summarise the evidence for the association between such exposures and adverse health outcomes. We systematically searched five electronic databases (PubMed, Embase, Web of Science, PsycNET, and CINAHL) for studies assessing the association between exposure to e-waste and outcomes related to mental health and neurodevelopment, physical health, education, and violence and criminal behaviour, from Jan 1, 1965, to Dec 17, 2012, and yielded 2274 records. Of the 165 full-text articles assessed for eligibility, we excluded a further 142, resulting in the inclusion of 23 published epidemiological studies that met the predetermined criteria. All studies were from southeast China. We assessed evidence of a causal association between exposure to e-waste and health outcomes within the Bradford Hill framework. We recorded plausible outcomes associated with exposure to e-waste including change in thyroid function, changes in cellular expression and function, adverse neonatal outcomes, changes in temperament and behaviour, and decreased lung function. Boys aged 8-9 years living in an e-waste recycling town had a lower forced vital capacity than did those living in a control town. Significant negative correlations between blood chromium concentrations and forced vital capacity in children aged 11 and 13 years were also reported. Findings from most studies showed increases in spontaneous abortions, stillbirths, and premature births, and reduced birthweights and birth lengths associated with exposure to e-waste. People living in e-waste recycling towns or working in e-waste recycling had evidence of greater DNA damage than did those living in control towns. Studies of the effects of exposure to e-waste on thyroid function were not

E-waste environmental contamination and harm to public health in China.

PubMed

Xu, Xijin; Zeng, Xiang; Boezen, H Marike; Huo, Xia

2015-06-01

The adverse effects of electronic waste (e-waste) on the human body have stirred up concern in recent years. China is one of the countries that confront serious pollution and human exposure of e-waste, and the majority of the population is exposed to potentially hazardous substances that are derived from informal e-waste recycling processes. This study reviews recent reports on human exposure to e-waste in China, with particular focus on exposure routes (e.g., inhalation and ingestion) and several toxicities of human (e.g., endocrine system, respiratory system, reproductive system, developmental toxicity, neurotoxicity, and genetic toxicity). Pieces of evidence that associate e-waste exposure with human health effects in China are assessed. The role of toxic heavy metals (e.g., lead, cadmium, chromium, mercury, and nickel) and organic pollutants (e.g., polybrominated diphenyl ethers (PBDEs), polychlorinated biphenyl (PCBs), polycyclic aromatic hydrocarbons (PAHs), polybrominated biphenyls (PBBs), polyhalogenated aromatic hydrocarbons (PHAHs), bisphenol A (BPA)) on human health is also briefly discussed.

Can Small Countries Benefit from the E-waste Global Value Chain?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meine Pieter, Dijk van, E-mail: mpvandijk@iss.nl

E-waste is a term used to cover items of all types of electrical and electronic equipment and its parts that have been discarded by the owners as waste without the intention of re-use, because this equipment has ceased to be of any value to its owners. E-waste is one of the fastestgrowing waste streams globally. Since the Rio Summit Earth summit organized by the United Nations in 1992, the concept of sustainability extends to rendering basic services such as Solid Waste Management and dealing with e-waste. People are afraid of e-waste because of its possible negative effects on health andmore » because it could pollute the environment. Indicators of unsustainable service provision concerninge-waste include irregular collection, open dumping, burning of solid and e-waste in open spaces. Often collection covers a small part of the country, cost recovery is limited or not existent, and one notes poor utilization of available resources with no or very limited reuse and recycling.« less

Developmental Neurotoxicants in E-Waste: An Emerging Health Concern

PubMed Central

Chen, Aimin; Dietrich, Kim N.; Huo, Xia; Ho, Shuk-mei

2011-01-01

Objective Electronic waste (e-waste) has been an emerging environmental health issue in both developed and developing countries, but its current management practice may result in unintended developmental neurotoxicity in vulnerable populations. To provide updated information about the scope of the issue, presence of known and suspected neurotoxicants, toxicologic mechanisms, and current data gaps, we conducted this literature review. Data sources We reviewed original articles and review papers in PubMed and Web of Science regarding e-waste toxicants and their potential developmental neurotoxicity. We also searched published reports of intergovernmental and governmental agencies and nongovernmental organizations on e-waste production and management practice. Data extraction We focused on the potential exposure to e-waste toxicants in vulnerable populations—that is, pregnant women and developing children—and neurodevelopmental outcomes. In addition, we summarize experimental evidence of developmental neurotoxicity and mechanisms. Data synthesis In developing countries where most informal and primitive e-waste recycling occurs, environmental exposure to lead, cadmium, chromium, polybrominated diphenyl ethers, polychlorinated biphenyls, and polycyclic aromatic hydrocarbons is prevalent at high concentrations in pregnant women and young children. Developmental neurotoxicity is a serious concern in these regions, but human studies of adverse effects and potential mechanisms are scarce. The unprecedented mixture of exposure to heavy metals and persistent organic pollutants warrants further studies and necessitates effective pollution control measures. Conclusions Pregnant women and young children living close to informal e-waste recycling sites are at risk of possible perturbations of fetus and child neurodevelopment. PMID:21081302

19. 1500 CUBIC FEET CAPACITY SCRAP STEEL CHARGING BOX ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. 1500 CUBIC FEET CAPACITY SCRAP STEEL CHARGING BOX ON THE CHARGING AISLE OF THE BOP SHOP LOOKING NORTHWEST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Recovery of fissile materials from nuclear wastes

DOEpatents

Forsberg, Charles W.

1999-01-01

A process for recovering fissile materials such as uranium, and plutonium, and rare earth elements, from complex waste feed material, and converting the remaining wastes into a waste glass suitable for storage or disposal. The waste feed is mixed with a dissolution glass formed of lead oxide and boron oxide resulting in oxidation, dehalogenation, and dissolution of metal oxides. Carbon is added to remove lead oxide, and a boron oxide fusion melt is produced. The fusion melt is essentially devoid of organic materials and halogens, and is easily and rapidly dissolved in nitric acid. After dissolution, uranium, plutonium and rare earth elements are separated from the acid and recovered by processes such as PUREX or ion exchange. The remaining acid waste stream is vitrified to produce a waste glass suitable for storage or disposal. Potential waste feed materials include plutonium scrap and residue, miscellaneous spent nuclear fuel, and uranium fissile wastes. The initial feed materials may contain mixtures of metals, ceramics, amorphous solids, halides, organic material and other carbon-containing material.

Food equipment manufacturer takes a slice out of its scrap rate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernard, D.; Hannahs, J.; Carter, M.

1996-09-01

The PMI Food Equipment Group began manufacturing circular slicer knives for its commercial Hobart line of slicers in the early 1930s. The company manufacturers the only cast knife in the food industry. The cast knives offer superior edge retention and overall corrosion resistance. The slicer knives are cast in PMI`s foundry. The casting process sometimes produces shrinkage voids or gas bubbles in the knife blank. Surface discontinuities often do not appear until rough cutting or final machining, i.e., after several hours of value-added manufacturing. Knife blanks with these discontinuities were scrapped and sent back to the foundry for remelting. Tomore » scrap the knives at that point meant the cost for casting plus the value-added machining added up to a considerable amount. Weld repair allows the recovery of casting and machining expenses equal to a significant percentage of the total manufacturing cost of slicer knives. Repair costs include welding, grinding, shipping, surface finishing and material handling. Other good applications for this GMAW-P process include repair of jet engine components, rotating process industry equipment, and hardfacing of cutting tools and dies. In addition, dissimilar metals and any material that is heat treated to develop its properties such as precision investment castings are excellent applications. The low resultant distortion, elimination of postweld heat treatment and non-line-of-site welding capability solves thin wall, limited access and precision machined component repair challenges.« less

SCRAP TIRE RECYCLING: CONVINCING BUSINESSES TO INTEGRATE INEXPENSIVE, CUTTING-EDGE TECHNOLOGY TO CONVERT TIRES INTO VARIOUS CONSTRUCTION MATERIALS

EPA Science Inventory

Scrap tires cause serious environmental pollution and health problems. Although worldwide figures are imprecise, it is known that one-fourth of the 283 million tires scrapped in the United States were landfilled last year. Hundreds of millions more tires ar...

The effect of ship scrapping industry and its associated wastes on the biomass production and biodiversity of biota in in situ condition at Alang.

PubMed

Tewari, A; Joshi, H V; Trivedi, R H; Sravankumar, V G; Raghunathan, C; Khambhaty, Y; Kotiwar, O S; Mandal, S K

2001-06-01

The main pollutants for the ship scrapping industry and its associated wastes at Alang are heavy metals, petroleum hydrocarbon and bacterial contaminations. The concentration of iron, manganese, cobalt, copper, zinc, lead, cadmium, nickel and mercury were 25 to 15,500% more at nearshore station of Alang as compared to control site at Piram. The concentration of heavy metals in the nearshore station of Alang was always higher than its concentration at 10 km away. The concentration of petroleum hydrocarbon was 16,973 and 53,900% more at the nearshore and 10 km away respectively at Alang as compared to controls. The concentration of chlorophyll-a and phaeophytin were in non-detectable range (< 0.2 and < 0.1 mg m3) or much lower concentration at both the stations of Alang as compared to controls. The total viable count, total coliform, Escherichia coli, Vibrio cholerae, Vibrio parahaemolyticus and other Vibrio, Streptococcus faecalis, Shigella, Salmonella, Proteus, and Klebsiella were always higher (17%-605%) at the nearshore station of Alang as compared to control. Similar trend was observed at 10 km away from Alang. Bacteria in sediment also showed the same pattern of variation. Phytoplankton counts at the nearshore station and 10 km away from Alang were only slightly raised. In contrast to phytoplankton, the zooplankton showed considerable reduction of growth (-10 to -66%) at Alang.

Contamination by trace elements at e-waste recycling sites in Bangalore, India.

PubMed

Ha, Nguyen Ngoc; Agusa, Tetsuro; Ramu, Karri; Tu, Nguyen Phuc Cam; Murata, Satoko; Bulbule, Keshav A; Parthasaraty, Peethmbaram; Takahashi, Shin; Subramanian, Annamalai; Tanabe, Shinsuke

2009-06-01

The recycling and disposal of electronic waste (e-waste) in developing countries is causing an increasing concern due to its effects on the environment and associated human health risks. To understand the contamination status, we measured trace elements (TEs) in soil, air dust, and human hair collected from e-waste recycling sites (a recycling facility and backyard recycling units) and the reference sites in Bangalore and Chennai in India. Concentrations of Cu, Zn, Ag, Cd, In, Sn, Sb, Hg, Pb, and Bi were higher in soil from e-waste recycling sites compared to reference sites. For Cu, Sb, Hg, and Pb in some soils from e-waste sites, the levels exceeded screening values proposed by US Environmental Protection Agency (EPA). Concentrations of Cr, Mn, Co, Cu, In, Sn, Sb, Tl, Pb and Bi in air from the e-waste recycling facility were relatively higher than the levels in Chennai city. High levels of Cu, Mo, Ag, Cd, In, Sb, Tl, and Pb were observed in hair of male workers from e-waste recycling sites. Our results suggest that e-waste recycling and its disposal may lead to the environmental and human contamination by some TEs. To our knowledge, this is the first study on TE contamination at e-waste recycling sites in Bangalore, India.

Selective recovery of cobalt, nickel and lithium from sulfate leachate of cathode scrap of Li-ion batteries using liquid-liquid extraction

NASA Astrophysics Data System (ADS)

Nguyen, Viet Tu; Lee, Jae-chun; Jeong, Jinki; Kim, Byung-Su; Pandey, B. D.

2014-03-01

This paper focuses on the extractive separation and selective recovery of cobalt, nickel and lithium from the sulfate leachate of cathode scrap generated during manufacture of lithium ion batteries (LIBs). The conditions for extraction, scrubbing and stripping of cobalt from nickel and lithium are optimized with an aqueous feed containing 25.1 g·dm-3 cobalt, 2.54 g·dm-3 nickel and 6.2 g·dm-3 lithium using Na-PC-88A. 99.8% Co is extracted with 60% Na-0.56 mol·dm-3 PC-88A in two counter-current stages at an O/A phase ratio of 3/1 and an equilibrium pH of 4.5. The "crowding effect" shown for the first time provides effective scrubbing of impurities (Ni and Li) with 2.0 g·dm-3 CoSO4 solution. The McCabe-Thiele diagram predicts the scrubbing of 99.9% Ni and 99.9% Li at an equilibrium pH of 4.75 and O/A of 2/1 in two stages. High purity (99.9%) cobalt sulfate along with Ni and Li from the leach liquor of cathode scrap is recovered by solvent extraction. The proposed process ensures complete recycling of the waste of the manufacturing process of LIBs.

Fungal Biorecovery of Gold From E-waste.

PubMed

Bindschedler, Saskia; Vu Bouquet, Thi Quynh Trang; Job, Daniel; Joseph, Edith; Junier, Pilar

2017-01-01

Waste electric and electronic devices (e-waste) represent a source of valuable raw materials of great interest, and in the case of metals, e-waste might become a prized alternative source. Regarding gold, natural ores are difficult to mine due to their refractory nature and the richest ores have almost all been exploited. Additionally, some gold mining areas are present in geopolitically unstable regions. Finally, the gold mining industry produces toxic compounds, such as cyanides. As a result, the gold present in e-waste represents a nonnegligible resource (urban mining). Extraction methods of gold from natural ores (pyro- and hydrometallurgy) have been adapted to this particular type of matrix. However, to propose novel approaches with a lower environmental footprint, biotechnological methods using microorganisms are being developed (biometallurgy). These processes use the extensive metabolic potential of microbes (algae, bacteria, and fungi) to mobilize and immobilize gold from urban and industrial sources. In this review, we focus on the use of fungi for gold biomining. Fungi interact with gold by mobilizing it through mechanical attack as well as through biochemical leaching by the production of cyanides. Moreover, fungi are also able to release Au through the degradation of cyanide from aurocyanide complexes. Finally, fungi immobilize gold through biosorption, bioaccumulation, and biomineralization, in particular, as gold nanoparticles. Overall, the diversity of mechanisms of gold recycling using fungi combined with their filamentous lifestyle, which allows them to thrive in heterogeneous and solid environments such as e-waste, makes fungi an important bioresource to be harnessed for the biorecovery of gold. Copyright © 2017 Elsevier Inc. All rights reserved.

Enhancing e-waste estimates: Improving data quality by multivariate Input–Output Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Feng, E-mail: fwang@unu.edu; Design for Sustainability Lab, Faculty of Industrial Design Engineering, Delft University of Technology, Landbergstraat 15, 2628CE Delft; Huisman, Jaco

2013-11-15

Highlights: • A multivariate Input–Output Analysis method for e-waste estimates is proposed. • Applying multivariate analysis to consolidate data can enhance e-waste estimates. • We examine the influence of model selection and data quality on e-waste estimates. • Datasets of all e-waste related variables in a Dutch case study have been provided. • Accurate modeling of time-variant lifespan distributions is critical for estimate. - Abstract: Waste electrical and electronic equipment (or e-waste) is one of the fastest growing waste streams, which encompasses a wide and increasing spectrum of products. Accurate estimation of e-waste generation is difficult, mainly due to lackmore » of high quality data referred to market and socio-economic dynamics. This paper addresses how to enhance e-waste estimates by providing techniques to increase data quality. An advanced, flexible and multivariate Input–Output Analysis (IOA) method is proposed. It links all three pillars in IOA (product sales, stock and lifespan profiles) to construct mathematical relationships between various data points. By applying this method, the data consolidation steps can generate more accurate time-series datasets from available data pool. This can consequently increase the reliability of e-waste estimates compared to the approach without data processing. A case study in the Netherlands is used to apply the advanced IOA model. As a result, for the first time ever, complete datasets of all three variables for estimating all types of e-waste have been obtained. The result of this study also demonstrates significant disparity between various estimation models, arising from the use of data under different conditions. It shows the importance of applying multivariate approach and multiple sources to improve data quality for modelling, specifically using appropriate time-varying lifespan parameters. Following the case study, a roadmap with a procedural guideline is provided to enhance e-waste

19 CFR 10.91 - Prototypes used exclusively for product development and testing.

Code of Federal Regulations, 2014 CFR

2014-04-01

... prototypes or any part(s) of the prototypes may be sold as scrap, waste, or for recycling, as prescribed in..., or for recycling. This includes a prototype or any part thereof that is incorporated into another product, as scrap, waste, or recycled material. If sold as scrap, waste, or for recycling, applicable duty...

19 CFR 10.91 - Prototypes used exclusively for product development and testing.

Code of Federal Regulations, 2011 CFR

2011-04-01

... prototypes or any part(s) of the prototypes may be sold as scrap, waste, or for recycling, as prescribed in..., or for recycling. This includes a prototype or any part thereof that is incorporated into another product, as scrap, waste, or recycled material. If sold as scrap, waste, or for recycling, applicable duty...

19 CFR 10.91 - Prototypes used exclusively for product development and testing.

Code of Federal Regulations, 2010 CFR

2010-04-01

... prototypes or any part(s) of the prototypes may be sold as scrap, waste, or for recycling, as prescribed in..., or for recycling. This includes a prototype or any part thereof that is incorporated into another product, as scrap, waste, or recycled material. If sold as scrap, waste, or for recycling, applicable duty...

19 CFR 10.91 - Prototypes used exclusively for product development and testing.

Code of Federal Regulations, 2012 CFR

2012-04-01

... prototypes or any part(s) of the prototypes may be sold as scrap, waste, or for recycling, as prescribed in..., or for recycling. This includes a prototype or any part thereof that is incorporated into another product, as scrap, waste, or recycled material. If sold as scrap, waste, or for recycling, applicable duty...

19 CFR 10.91 - Prototypes used exclusively for product development and testing.

Code of Federal Regulations, 2013 CFR

2013-04-01

... prototypes or any part(s) of the prototypes may be sold as scrap, waste, or for recycling, as prescribed in..., or for recycling. This includes a prototype or any part thereof that is incorporated into another product, as scrap, waste, or recycled material. If sold as scrap, waste, or for recycling, applicable duty...

A roadmap for development of sustainable E-waste management system in India.

PubMed

Wath, Sushant B; Vaidya, Atul N; Dutt, P S; Chakrabarti, Tapan

2010-12-01

The problem of E-waste has forced Environmental agencies of many countries to innovate, develop and adopt environmentally sound options and strategies for E-waste management, with a view to mitigate and control the ever growing threat of E-waste to the environment and human health. E-waste management is given the top priority in many developed countries, but in rapid developing countries like India, it is difficult to completely adopt or replicate the E-waste management system in developed countries due to many country specific issues viz. socio-economic conditions, lack of infrastructure, absence of appropriate legislations for E-waste, approach and commitments of the concerned, etc. This paper presents a review and assessment of the E-waste management system of developed as well as developing countries with a special emphasis on Switzerland, which is the first country in the world to have established and implemented a formal E-waste management system and has recycled 11kg/capita of WEEE against the target of 4kg/capita set by EU. And based on the discussions of various approaches, laws, legislations, practices of different countries, a road map for the development of sustainable and effective E-waste management system in India for ensuring environment, as well as, occupational safety and health, is proposed. Copyright © 2010 Elsevier B.V. All rights reserved.

An Analytic Tool to Investigate the Effect of Binder on the Sensitivity of HMX-Based Plastic Bonded Explosives in the Skid Test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hayden, D. W.

This project will develop an analytical tool to calculate performance of HMX based PBXs in the skid test. The skid-test is used as a means to measure sensitivity for large charges in handling situations. Each series of skid tests requires dozens of drops of large billets. It is proposed that the reaction (or lack of one) of PBXs in the skid test is governed by the mechanical properties of the binder. If true, one might be able to develop an analytical tool to estimate skid test behavior for new PBX formulations. Others over the past 50 years have tried tomore » develop similar models. This project will research and summarize the works of others and couple the work of 3 into an analytical tool that can be run on a PC to calculate drop height of HMX based PBXs. Detonation due to dropping a billet is argued to be a dynamic thermal event. To avoid detonation, the heat created due to friction at impact, must be conducted into the charge or the target faster than the chemical kinetics can create additional energy. The methodology will involve numerically solving the Frank-Kamenetskii equation in one dimension. The analytical problem needs to be bounded in terms of how much heat is introduced to the billet and for how long. Assuming an inelastic collision with no rebound, the billet will be in contact with the target for a short duration determined by the equations of motion. For the purposes of the calculations, it will be assumed that if a detonation is to occur, it will transpire within that time. The surface temperature will be raised according to the friction created using the equations of motion of dropping the billet on a rigid surface. The study will connect the works of Charles Anderson, Alan Randolph, Larry Hatler, Alfonse Popolato, and Charles Mader into a single PC based analytic tool. Anderson's equations of motion will be used to calculate the temperature rise upon impact, the time this temperature is maintained (contact time) will be obtained from the

46 CFR Sec. 12 - Disposition of removed equipment and scrap.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 8 2013-10-01 2013-10-01 false Disposition of removed equipment and scrap. Sec. 12 Section 12 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION A-NATIONAL SHIPPING AUTHORITY PROCEDURE FOR ACCOMPLISHMENT OF VESSEL REPAIRS UNDER NATIONAL SHIPPING AUTHORITY MASTER LUMP SUM REPAIR...

21. Scrapping In Dry Dock #4. Naval Shipyard Philadelphia. February ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. Scrapping In Dry Dock #4. Naval Shipyard Philadelphia. February 18, 1946. Original Photograph In Collection of National Archives, Mid-Atlantic Regional Records Center, Philadelphia. - Naval Base Philadelphia-Philadelphia Naval Shipyard, Dry Dock No. 4, Broad Street south of Government Avenue, Philadelphia, Philadelphia County, PA

Speciation and Characterization of E-Waste, Using Analytical Techniques

NASA Astrophysics Data System (ADS)

López, C. Cortés; Cruz, V. E. Reyes; Rodríguez, M. A. Veloz; Ávila, J. Hernández; Badillo, J. Flores; Murcia, J. A. Cobos

Electronic waste (e-waste), have a high potential as a source of precious metals, since they can contain metals like silver, gold, platinum, copper, zinc, nickel, tin and others. In this paper some e-waste were characterized using several analytical techniques as Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and inductively coupled plasma (ICP) in addition to the thermodynamic study by Pourbaix diagrams of silver (Ag), gold (Au), platinum (Pt), copper (Cu), nickel (Ni), tin (Sn) and zinc (Zn); considering an average low concentration of HNO3 (10% v/v). With results of the characterization was determined that the e-waste is an ideal source for the recovery of valuable metals. Similarly, the thermodynamic studies showed that it is possible to obtain all metallic species except Pt, in a potential window of 1.45V to 2.0V vs SCE.

Special Report: E-Waste Management in the United States and Public Health Implications.

PubMed

Seeberger, Jessica; Grandhi, Radhika; Kim, Stephani S; Mase, William A; Reponen, Tiina; Ho, Shuk-mei; Chen, Aimin

2016-10-01

Electronic waste (e-waste) generation is increasing worldwide, and its management becomes a significant challenge because of the many toxicants present in electronic devices. The U.S. is a major producer of e-waste, although its management practice and policy regulation are not sufficient to meet the challenge. We reviewed e-waste generation, current management practices and trends, policy challenges, potential health impact, and toxicant exposure prevention in the U.S. A large amount of toxic metals, flame retardants, and other persistent organic pollutants exist in e-waste or can be released from the disposal of e-waste (e.g., landfill, incineration, recycling). Landfill is still a major method used to dispose of obsolete electronic devices, and only about half of the states have initiated a landfill ban for e-waste. Recycling of e-waste is an increasing trend in the past few years. There is potential, however, for workers to be exposed to a mixture of toxicants in e-waste and these exposures should be curtailed. Perspectives and recommendations are provided regarding managing e-waste in the U.S. to protect public health, including enacting federal legislation, discontinuing landfill disposal, protecting workers in recycling facilities from toxicant exposure, reducing toxicant release into the environment, and raising awareness of this growing environmental health issue among the public.

Distillation of granulated scrap tires in a pilot plant.

PubMed

López, Félix A; Centeno, Teresa A; Alguacil, Francisco José; Lobato, Belén

2011-06-15

This paper reports the pyrolytic treatment of granulated scrap tires (GST) in a pilot distillation unit at moderate temperature (550°C) and atmospheric pressure, to produce oil, char and gas products. Tire-derived oil is a complex mixture of organic C(5)-C(24) compounds, including a very large proportion of aromatic compounds. This oil has a high gross calorific value (∼ 43 MJ kg(-1)) and N and S contents of 0.4% and 0.6%, respectively, falling within the specifications of certain heating fuels. The distillation gas is composed of hydrocarbons; methane and n-butane are the most abundant, investing the distillation gas with a very high gross calorific value (∼ 68 MJ Nm(-3)). This gas is transformed into electric power by a co-generation turbine. The distillation char is mostly made of carbon but with significant inorganic impurities (∼ 12 wt%). The quality of the solid residue of the process is comparable to that of some commercial chars. The quantity of residual solids, and the qualities of the gas, liquid and solid fractions, are similar to those obtained by conventional pyrolytic treatments of waste tires. However, the simplicity of the proposed technology and its low investment costs make it a very attractive alternative. Copyright © 2011 Elsevier B.V. All rights reserved.

Lithium Carbonate Recovery from Cathode Scrap of Spent Lithium-Ion Battery: A Closed-Loop Process.

PubMed

Gao, Wenfang; Zhang, Xihua; Zheng, Xiaohong; Lin, Xiao; Cao, Hongbin; Zhang, Yi; Sun, Zhi

2017-02-07

A closed-loop process to recover lithium carbonate from cathode scrap of lithium-ion battery (LIB) is developed. Lithium could be selectively leached into solution using formic acid while aluminum remained as the metallic form, and most of the other metals from the cathode scrap could be precipitated out. This phenomenon clearly demonstrates that formic acid can be used for lithium recovery from cathode scrap, as both leaching and separation reagent. By investigating the effects of different parameters including temperature, formic acid concentration, H 2 O 2 amount, and solid to liquid ratio, the leaching rate of Li can reach 99.93% with minor Al loss into the solution. Subsequently, the leaching kinetics was evaluated and the controlling step as well as the apparent activation energy could be determined. After further separation of the remaining Ni, Co, and Mn from the leachate, Li 2 CO 3 with the purity of 99.90% could be obtained. The final solution after lithium carbonate extraction can be further processed for sodium formate preparation, and Ni, Co, and Mn precipitates are ready for precursor preparation for cathode materials. As a result, the global recovery rates of Al, Li, Ni, Co, and Mn in this process were found to be 95.46%, 98.22%, 99.96%, 99.96%, and 99.95% respectively, achieving effective resources recycling from cathode scrap of spent LIB.

Bulky waste quantities and treatment methods in Denmark.

PubMed

Larsen, Anna W; Petersen, Claus; Christensen, Thomas H

2012-02-01

Bulky waste is a significant and increasing waste stream in Denmark. However, only little research has been done on its composition and treatment. In the present study, data about collection methods, waste quantities and treatment methods for bulky waste were obtained from two municipalities. In addition a sorting analysis was conducted on combustible waste, which is a major fraction of bulky waste in Denmark. The generation of bulky waste was found to be 150-250 kg capita(-1) year(-1), and 90% of the waste was collected at recycling centres; the rest through kerbside collection. Twelve main fractions were identified of which ten were recyclable and constituted 50-60% of the total quantity. The others were combustible waste for incineration (30-40%) and non-combustible waste for landfilling (10%). The largest fractions by mass were combustible waste, bricks and tile, concrete, non-combustible waste, wood, and metal scrap, which together made up more than 90% of the total waste amounts. The amount of combustible waste could be significantly reduced through better sorting. Many of the waste fractions consisted of composite products that underwent thorough separation before being recycled. The recyclable materials were in many cases exported to other countries which made it difficult to track their destination and further treatment.

Use of cold-bonded, waste oxide briquettes at U.S. Steel Mon Valley BOP shop

DOE Office of Scientific and Technical Information (OSTI.GOV)

DiCaprio, V.; Howell, K.; Harris, R.

1995-09-01

In attempts to avoid the escalated costs and environmental concerns associated with taking waste oxide materials to a landfill, National Recovery Systems Inc., in conjunction with US Steel, built a waste oxide briquetting facility at the USS Mon Valley works (Edgar Thomson plant) to recycle various sludges and scales. The waste oxide briquette is currently a blend of BOP classifier sludge, BOP filter drum sludge, casterscale and hot strip mill scale. In addition to the landfill cost avoidance, the waste oxide briquette is also a low cast, steel scrap supplement. This paper describes the production of the waste oxide briquettemore » and the use of the recycled material at the Edgar Thomson BOP shop.« less

Pyrolysis process for the treatment of scrap tyres: preliminary experimental results.

PubMed

Galvagno, S; Casu, S; Casabianca, T; Calabrese, A; Cornacchia, G

2002-01-01

The aim of this work is the evaluation, on a pilot scale, of scrap tyre pyrolysis process performance and the characteristics of the products under different process parameters, such as temperature, residence time, pressure, etc. In this frame, a series of tests were carried out at varying process temperatures between 550 and 680 degrees C, other parameters being equal. Pyrolysis plant process data are collected by an acquisition system; scrap tyre samples used for the treatment, solid and liquid by-products and produced syngas were analysed through both on-line monitoring (for gas) and laboratory analyses. Results show that process temperature, in the explored range, does not seem to seriously influence the volatilisation reaction yield, at least from a quantitative point of view, while it observably influences the distribution of the volatile fraction (liquid and gas) and by-products characteristics.

Palladium and gold removal and recovery from precious metal solutions and electronic scrap leachates by Desulfovibrio desulfuricans.

PubMed

Creamer, Neil J; Baxter-Plant, Victoria S; Henderson, John; Potter, M; Macaskie, Lynne E

2006-09-01

Biomass of Desulfovibrio desulfuricans was used to recover Au(III) as Au(0) from test solutions and from waste electronic scrap leachate. Au(0) was precipitated extracellularly by a different mechanism from the biodeposition of Pd(0). The presence of Cu(2+) ( approximately 2000 mg/l) in the leachate inhibited the hydrogenase-mediated removal of Pd(II) but pre-palladisation of the cells in the absence of added Cu(2+) facilitated removal of Pd(II) from the leachate and more than 95% of the Pd(II) was removed autocatalytically from a test solution supplemented with Cu(II) and Pd(II). Metal recovery was demonstrated in a gas-lift electrobioreactor with electrochemically generated hydrogen, followed by precipitation of recovered metal under gravity. A 3-stage bioseparation process for the recovery of Au(III), Pd(II) and Cu(II) is proposed.

E-waste management and sustainability: a case study in Brazil.

PubMed

Azevedo, Luís Peres; da Silva Araújo, Fernando Gabriel; Lagarinhos, Carlos Alberto Ferreira; Tenório, Jorge Alberto Soares; Espinosa, Denise Crocce Romano

2017-11-01

The advancement of technology and development of new electronic and electrical equipment with a reduced life cycle has increased the need for the disposal of them (called Waste of Electric and Electronic Equipment or simply e-waste) due to defects presented during use, replacement of obsolete equipment, and ease of acquisition of new equipment. There is a lack of consumer awareness regarding the use, handling storage, and disposal of this equipment. In Brazil, the disposal of post-consumer waste is regulated by the National Solid Waste Policy, established by Law No. 12305 and regulated on the 23rd December 2010. Under this legislation, manufacturers and importers are required to perform a project for the Reverse Logistics of e-waste, though its implementation is not well defined. This work focuses on the verification of the sustainability of reverse logistics suggested by the legislation and the mandatory points, evaluating its costs and the possible financial gain with recycling of the waste. The management of reverse logistics and recycling of waste electrical and electronic equipment, or simply recycling of e-waste, as suggested by the government, will be the responsibility of the managing organization to be formed by the manufacturers/importers in Brazil.

Evaluation of Skid Resistance of Wearing Course Made Of Stone Mastic Asphalt Mixture in Laboratory Conditions

NASA Astrophysics Data System (ADS)

Wasilewska, Marta

2017-10-01

This paper presents the comparison of skid resistance of wearing course made of SMA (Stone Mastic Asphalt) mixtures which differ in resistance to polishing of coarse aggregate. Dolomite, limestone, granite and trachybasalt were taken for investigation. SMA mixtures have the same nominal size of aggregate (11 mm) and very similar aggregate particle-size distribution in mineral mixtures. Tested SMA11 mixtures were designed according to EN 13108-5 and Polish National Specification WT-2: 2014. Evaluation of the skid resistance has been performed using the FAP (Friction After Polishing) test equipment also known as the Wehner/Schulze machine. Laboratory method enables to compare the skid resistance of different types of mixtures under specified conditions simulating polishing processes. Tests were performed on both the specimens made of each coarse aggregate and SMA11 mixtures containing these aggregates. Measuring of friction coefficient μm was conducted before and during polishing process up to 180 0000 passes of polishing head. Comparison of the results showed differences in sensitivity to polishing among particular mixtures which depend on the petrographic properties of rock used to produce aggregate. Limestone and dolomite tend to have a fairly uniform texture with low hardness which makes these rock types susceptible to rapid polishing. This caused lower coefficient of friction for SMA11 mixtures with limestone and dolomite in comparison with other test mixtures. These significant differences were already registered at the beginning of the polishing process. Limestone aggregate had lower value of μm before starting the process than trachybasalt and granite aggregate after its completion. Despite the differences in structure and mineralogical composition between the granite and trachybasalt, slightly different values of the friction coefficient at the end of polishing were obtained. Images of the surface were taken with the optical microscope for better

Water Treatment Residuals and Scrap Tire Rubber as Green Sorbents for Removal of Stormwater Metals.

PubMed

Deng, Yang; Morris, Ciapha; Rakshit, Sudipta; Landa, Edward; Punamiya, Pravin; Sarkar, Dibyendu

2016-06-01

Bench scale tests were performed to evaluate two recycled wastes, water treatment residuals (WTR) and scrap tire rubber (STR), for adsorption of selected metals from urban stormwater, and assess their release from used sorbents. Aluminum-WTR alone could rapidly and effectively remove Cu, Pb, and Zn, while STR alone continuously released Zn accompanied with Cu and Pb adsorption. Zn leaching from STR was significantly reduced in the presence of WTR. Very little metals released from used combined adsorbents in NaNO3 solution, and only part of them were extracted with EDTA (a strong chelating agent), suggesting that metal release is not a concern in a typical stormwater condition. A combination of WTR and STR is a new, effective method for mitigation of urban stormwater metals-WTR can inhibit the STR leaching, and STR improves the hydraulic permeability of WTR powders, a limiting factor for stormwater flow when WTR is used alone.

High levels of antimony in dust from e-waste recycling in southeastern China.

PubMed

Bi, Xiangyang; Li, Zhonggen; Zhuang, Xiaochun; Han, Zhixuan; Yang, Wenlin

2011-11-01

Environmental contamination due to uncontrolled e-waste recycling is an emerging global issue. Antimony (Sb) is a toxic element used in semiconductor components and flame retardants for circuit board within electronic equipment. When e-waste is recycled, Sb is released and contaminates the surrounding environment; however, few studies have characterized the extent of this problem. In this study, we investigated Sb and arsenic (As) distributions in indoor dust from 13 e-waste recycling villages in Guiyu, Guangdong Province, southeastern China. Results revealed significantly elevated concentrations of Sb (6.1-232 mg/kg) in dust within all villages, which were 3.9-147 times higher than those from the non e-waste sites, indicating e-waste recycling was an important source of Sb pollution. On the contrary, As concentrations (5.4-17.7 mg/kg) in e-waste dusts were similar to reference values from the control sites. Therefore, dusts emitted from e-waste recycling may be characterized by high Sb/As ratios, which may help identify the contamination due to the e-waste recycling activities. Copyright © 2011 Elsevier B.V. All rights reserved.

Leaching of heavy metals from E-waste in simulated landfill columns

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li Yadong; Richardson, Jay B.; Mark Bricka, R.

2009-07-15

In recent history the volume of electronic products purchased by consumers has dramatically escalated. As a result this has produced an ever-increasing electronic waste (E-waste) stream, which has generated concerns regarding the E-waste's potential for adversely impacting the environment. The leaching of toxic substances from obsolete personal computers (PCs) and cathode ray tubes (CRTs) of televisions and monitors, which are the most significant components in E-waste stream, was studied using landfill simulation in columns. Five columns were employed. One column served as a control which was filled with municipal solid waste (MSW), two columns were filled with a mixture ofmore » MSW and CRTs, and the other two were filled with MSW and computer components including printed wire boards, hard disc drives, floppy disc drives, CD/DVD drives, and power supply units. The leachate generated from the columns was monitored for toxic materials throughout the two-year duration of the study. Results indicate that lead (Pb) and various other heavy metals that were of environmental and health concern were not detected in the leachate from the simulators. When the samples of the solids were collected from underneath the E-waste in the columns and were analyzed, significant amount of Pb was detected. This indicates that Pb could readily leach from the E-waste, but was absorbed by the solids around the E-waste materials. While Pb was not observed in the leachate in this study, it is likely that the Pb would eventually enter the leachate after a long term transport.« less

CHARACTERIZATION OF EMISSIONS FROM THE SIMULATED OPEN BURNING OF SCRAP TIRES

EPA Science Inventory

The report gives results of a small-scale combustion study, designed to collect, identify, and quantify products emitted during the simulated open burning of scrap tires. Fixed combustion gas, volatile and semi-volatile organic, particulate, and airborne metals data were collecte...

Co-combustion of E+E waste plastics in the TAMARA test plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vehlow, J.; Wanke, T.; Bergfeldt, B.

1997-12-01

The co-combustion of different amounts of various plastic fractions of electrical and electronic (E+E) waste together with municipal solid waste has been tested in the Karlsruhe test incinerator TAMARA. The tests revealed no negative influences upon the combustion process. In general the increased heating value of the fuel causes an improved burnout in all residue streams. The halogens Cl and Br added with the plastics are mainly transferred as HCl or HBr into the flue gas. An influence upon the formation of chlorinated dioxins and furans could not be observed. With increasing Br feed bromine containing homologues were detected inmore » the raw gas. The furans formed easier than the dioxins and those homologues carrying one Br atom were by far prevailing. Even at high Br input the total amount of mixed halogenated species was limited to approximately 30% of the total load of such compounds which did not leave the typical operation window for PCDD/PCDF in TAMARA. The co-combustion tests demonstrated that MSW combustion is an ecologically acceptable and economically sound disposal route for limited amounts of specific E+E waste.« less

An evaluation of the effects of tread depth, pavement texture, and water film thickness on skid number-speed gradients : supplement.

DOT National Transportation Integrated Search

1975-03-01

The raw data and the initial curves for the study entitled, "An Evaluation of the Effects of Tread Depth, Pavement Texture, and Water Film Thickness on Skid Number-Speed Gradients" are so voluminous that they are included in the Supplement rather tha...

INTERIOR VIEW, LOOKING NORTH, TOWARDS CUPOLA WHERE SCRAP METAL AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, LOOKING NORTH, TOWARDS CUPOLA WHERE SCRAP METAL AND OTHER COMPONENTS ARE MELTED TO CREATE DUCTILE IRON. BRIGHT FLASH IN BACKGROUND RESULTS FROM MOLTEN METAL (DUCTILE IRON) BEING POURED FROM CUPOLA INTO TRANSFER LADLE. - McWane Cast Iron Pipe Company, Pipe Casting Area, 1201 Vanderbilt Road, Birmingham, Jefferson County, AL

Long-term stand growth after helicopter and ground-based skidding in a tupelo-cypress wetland: 21-year results

Treesearch

D.E. Evans; W.M. Aust; J.A. Peterson

2013-01-01

Three disturbance treatments were implemented on a tupelo-cypress forested wetland in southwestern Alabama on the Tensaw River in 1986: (1) clearcutting with helicopter log removal (HELI), (2) HELI followed by rubber-tired skidder traffic simulation (SKID), and (3) HELI followed by removal of all vegetation during the first two growing seasons via glyphosate herbicide...

Generation of and control measures for, e-waste in Hong Kong

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung Shanshan, E-mail: sschung@hkbu.edu.hk; Lau Kayan; Zhang Chan

2011-03-15

While accurately estimating electrical and electronic waste (e-waste) generation is important for building appropriate infrastructure for its collection and recycling, making reliable estimates of this kind is difficult in Hong Kong owing to the fact that neither accurate trade statistics nor sales data of relevant products are available. In view of this, data of e-products consumption at household level was collected by a tailor-made questionnaire survey from the public for obtaining a reasonable e-waste generation estimate. It was estimated that on average no more than 80,443 tonnes (11.5 kg/capita) of waste is generated from non-plasma and non-liquid crystal display televisions,more » refrigerators, washing machines, air-conditioners and personal computers each year by Hong Kong households. However, not more than 17% of this is disposed as waste despite a producer responsibility scheme (PRS) not being in place because of the existence of a vibrant e-waste trading sector. The form of PRS control that can possibly win most public support is one that would involve the current e-waste traders as a major party in providing the reverse logistics with a visible recycling charge levied at the point of importation. This reverse logistic service should be convenient, reliable and highly accessible to the consumers.« less

Generation of and control measures for, e-waste in Hong Kong.

PubMed

Chung, Shan-shan; Lau, Ka-yan; Zhang, Chan

2011-03-01

While accurately estimating electrical and electronic waste (e-waste) generation is important for building appropriate infrastructure for its collection and recycling, making reliable estimates of this kind is difficult in Hong Kong owing to the fact that neither accurate trade statistics nor sales data of relevant products are available. In view of this, data of e-products consumption at household level was collected by a tailor-made questionnaire survey from the public for obtaining a reasonable e-waste generation estimate. It was estimated that on average no more than 80,443 tones (11.5 kg/capita) of waste is generated from non-plasma and non-liquid crystal display televisions, refrigerators, washing machines, air-conditioners and personal computers each year by Hong Kong households. However, not more than 17% of this is disposed as waste despite a producer responsibility scheme (PRS) not being in place because of the existence of a vibrant e-waste trading sector. The form of PRS control that can possibly win most public support is one that would involve the current e-waste traders as a major party in providing the reverse logistics with a visible recycling charge levied at the point of importation. This reverse logistic service should be convenient, reliable and highly accessible to the consumers. Copyright © 2010 Elsevier Ltd. All rights reserved.

Kinetics of Brominated Flame Retardant (BFR) Releases from Granules of Waste Plastics.

PubMed

Sun, Bingbing; Hu, Yuanan; Cheng, Hefa; Tao, Shu

2016-12-20

Plastic components of e-waste contain high levels of brominated flame retardants (BFRs), whose releases cause environmental and human health concerns. This study characterized the release kinetics of polybrominated diphenyl ethers (PBDEs) from millimeter-sized granules processed from the plastic exteriors of two scrap computer displays at environmentally relevant temperatures. The release rate of a substitute of PBDEs, 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE), from the waste plastics, was reported for the first time. Deca-BDE was the most abundant PBDE congeners in both materials (87-89%), while BTBPE was also present at relatively high contents. The release kinetics of BFRs could be modeled as one-dimensional diffusion, while the temperature dependence of diffusion coefficients was well described by the Arrhenius equation. The diffusion coefficients of BFRs (at 30 °C) in the plastic matrices were estimated to be in the range of 10 -27.16 to 10 -19.96 m 2 ·s -1 , with apparent activation energies between 88.4 and 154.2 kJ·mol -1 . The half-lives of BFR releases (i.e., 50% depletion) from the plastic granules ranged from thousands to tens of billions of years at ambient temperatures. These findings suggest that BFRs are released very slowly from the matrices of waste plastics through molecular diffusion, while their emissions can be significantly enhanced with wear-and-tear and pulverization.

Preparation and characterization of activated carbon from the char produced in the thermolysis of granulated scrap tyres.

PubMed

López, F A; Centeno, T A; Rodríguez, O; Alguacil, E J

2013-05-01

The char produced in the thermolysis of granulated scrap tyres has few market outlets, reducing the economic viability of the thermolytic process. This paper reports the potential of this char as a low-cost precursor of porous carbons. The tyre-derived char was demineralized in either alkaline or acidic media to reduce its ash, zinc, sulfur, and silica contents. The lowest impurity content was achieved with an HNO3/H2O treatment. The resulting demineralized char was then subjected to activation by KOH or CO2. The Brunauer-Emmett-Teller (BET)-specific surface area of the activated carbon produced by the KOH treatment was 242 m2/g, whereas that of the CO2-activated carbon was 720 m2/g. The textural properties of the latter product were similar to those of some commercial activated carbons. The use of tyre-derived char as a precursor of porous carbons could render the thermolytic treatment of scrap tyres more economically attractive. Char produced in thermolysis of granulated scrap tyres has a few market outlets; in this paper an alternative for its use is presented. The char was converted into activated carbon with textural properties similar to those of some commercial activated carbons. This process could render the thermolytic treatment of scrap tyres more economically attractive.

Assessment of DOE radioactive scrap metal disposition options

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, C.R.; Kasper, K.M.; Bossart, S.J.

1997-02-01

The DOE has amassed a large amount of radioactively-contaminated scrap metal (RSM) as a result of past operations and decontamination and decommissioning (D&D) projects. The volume of RSM will continue to increase as a result of the D&D of more than 6,000 surplus facilities and many of the 14,000 operating facilities in the DOE complex. RSM can be either surface contaminated or volumetrically contaminated, or both, with varying amounts of radioactivity. Several options exist for the disposition of this RSM, including disposal as radioactive waste, recycling by decontamination and free-release for unrestricted use, or recycling for restricted reuse inside amore » DOE controlled area. The DOE Office of Science and Technology (EM-50) has been actively investing in technology and strategy development in support of restricted-reuse RSM recycling for the past several years. This paper will assess the nature of the RSM recycling issue, review past investment by DOE to develop technologies and strategies to recycle RSM, and then discuss some recommendations concerning future investments in support of RSM management. Available information on the supply of RSM will be presented in Section II. The regulatory and policy framework concerning recycling RSM will be presented in Section III. A review of DOE investment in RSM recycling technology and current programs will be presented in Section IV. The current and projected industrial capacity will be described in Section V. And, finally, a discussion of issues and recommendations regarding DOE technology development interests in RSM recycling will be presented in Section VI and VII, respectively.« less

Dissolution Behaviour of Metal Elements from Several Types of E-waste Using Leaching Test

NASA Astrophysics Data System (ADS)

Nor, Nik Hisyamudin Muhd; Amira Nordin, Nurul; Mohamad, Fariza; Jaibee, Shafizan; Ismail, Al Emran; Omar, Badrul; Fauzi Ahmad, Mohd; Rahim, Abd Khalil Abd; Kamaruddin, Muhamad Khalif Ikhwan Mohd; Turan, Faiz Mohd; Abu Bakar, Elmi; Yokoyama, Seiji

2017-08-01

Rapid development of the electrical and electronic was increasing annually due to the demand by the human being. Increasing production of electrical and electronic product led to the increasing of electric and electronic waste or can be called as the e-waste. The UN Environment Programme estimates that the world generates 20-50 million tons of the e-waste each year and the amount is raising three times faster than other forms of municipal waste. This study is focusing on the investigation of the dissolution behaviour of metal element from several types of e-waste by hydrometallurgical process. Leaching test was conducted on the e-waste by using acid as the reagent solution. Prior to the leaching test, manual dismantling, separation, and crushing process were carried out to the e-waste. The e-waste were characterized by Scanning Electron Microcopy (SEM) and the Energy Dispersive X-ray Spectroscopy (EDX) to define the elements inside the sample of e-waste. While the liquid residue from leaching test was analyzed by using Inductively Couple Plasma-Mass Spectrometer (ICP-MS) to define the dissolution behaviour of the metal element that contain in the e-waste. It was found that the longest time for dismantling process was the dismantling of laptop. The dissolution behaviour of Fe, Al, Zn and Pb elements in the e-waste has affected to the increase of pH. The increasing pH led to the reduction of the metals element during leaching process.

A systematic review of the human body burden of e-waste exposure in China.

PubMed

Song, Qingbin; Li, Jinhui

2014-07-01

As China is one of the countries facing the most serious pollution and human exposure effects of e-waste in the world, much of the population there is exposed to potentially hazardous substances due to informal e-waste recycling processes. This report reviews recent studies on human exposure to e-waste in China, with particular focus on exposure routes (e.g. dietary intake, inhalation, and soil/dust ingestion) and human body burden markers (e.g. placenta, umbilical cord blood, breast milk, blood, hair, and urine) and assesses the evidence for the association between such e-waste exposure and the human body burden in China. The results suggest that residents in the e-waste exposure areas, located mainly in the three traditional e-waste recycling sites (Taizhou, Guiyu, and Qingyuan), are faced with a potential higher daily intake of these pollutants than residents in the control areas, especially via food ingestion. Moreover, pollutants (PBBs, PBDEs, PCBs, PCDD/Fs, and heavy metals) from the e-waste recycling processes were all detectable in the tissue samples at high levels, showing that they had entered residents' bodies through the environment and dietary exposure. Children and neonates are the groups most sensitive to the human body effects of e-waste exposure. We also recorded plausible outcomes associated with exposure to e-waste, including 7 types of human body burden. Although the data suggest that exposure to e-waste is harmful to health, better designed epidemiological investigations in vulnerable populations, especially neonates and children, are needed to confirm these associations. Copyright © 2014 Elsevier Ltd. All rights reserved.

State-of-the-art of recycling e-wastes by vacuum metallurgy separation.

PubMed

Zhan, Lu; Xu, Zhenming

2014-12-16

In recent era, more and more electric and electronic equipment wastes (e-wastes) are generated that contain both toxic and valuable materials in them. Most studies focus on the extraction of valuable metals like Au, Ag from e-wastes. However, the recycling of metals such as Pb, Cd, Zn, and organics has not attracted enough attentions. Vacuum metallurgy separation (VMS) processes can reduce pollution significantly using vacuum technique. It can effectively recycle heavy metals and organics from e-wastes in an environmentally friendly way, which is beneficial for both preventing the heavy metal contaminations and the sustainable development of resources. VMS can be classified into several methods, such as vacuum evaporation, vacuum carbon reduction and vacuum pyrolysis. This paper respectively reviews the state-of-art of these methods applied to recycling heavy metals and organics from several kinds of e-wastes. The method principle, equipment used, separating process, optimized operating parameters and recycling mechanism of each case are illustrated in details. The perspectives on the further development of e-wastes recycling by VMS are also presented.

Enhancing e-waste estimates: improving data quality by multivariate Input-Output Analysis.

PubMed

Wang, Feng; Huisman, Jaco; Stevels, Ab; Baldé, Cornelis Peter

2013-11-01

Waste electrical and electronic equipment (or e-waste) is one of the fastest growing waste streams, which encompasses a wide and increasing spectrum of products. Accurate estimation of e-waste generation is difficult, mainly due to lack of high quality data referred to market and socio-economic dynamics. This paper addresses how to enhance e-waste estimates by providing techniques to increase data quality. An advanced, flexible and multivariate Input-Output Analysis (IOA) method is proposed. It links all three pillars in IOA (product sales, stock and lifespan profiles) to construct mathematical relationships between various data points. By applying this method, the data consolidation steps can generate more accurate time-series datasets from available data pool. This can consequently increase the reliability of e-waste estimates compared to the approach without data processing. A case study in the Netherlands is used to apply the advanced IOA model. As a result, for the first time ever, complete datasets of all three variables for estimating all types of e-waste have been obtained. The result of this study also demonstrates significant disparity between various estimation models, arising from the use of data under different conditions. It shows the importance of applying multivariate approach and multiple sources to improve data quality for modelling, specifically using appropriate time-varying lifespan parameters. Following the case study, a roadmap with a procedural guideline is provided to enhance e-waste estimation studies. Copyright © 2013 Elsevier Ltd. All rights reserved.

Skid steer fuel cell powered unmanned ground vehicle (Burro)

NASA Astrophysics Data System (ADS)

Meldrum, Jay S.; Green, Christopher A.

2008-04-01

The use of alternative energy technology for vehicle propulsion and auxiliary power is becoming more important. Work is being performed at Michigan Technological University's Keweenaw Research Center on an Army Research Laboratory cooperative agreement to develop two unmanned ground vehicles for military applications. A wide range of alternative energy technologies were investigated. Hydrogen-powered proton exchange membrane fuel cells were identified as the most appropriate alternative energy source. This is due to some development and commercialization which makes the technology "drop-in plug-in" for immediate use. We have previously presented research work on a small unmanned ground vehicle demonstration platform where the fuel cell is the only power source. We now present research work on the integration of a fuel cell onto a larger skid steer platform. The dual-power capability of this vehicle can provide a modest level of propulsion in "engine-off mode" and may also be used to power directed energy devices which have applications in countermine and similar threat technologies.

Leaching kinetics of cobalt from the scraps of spent aerospace magnetic materials.

PubMed

Zhou, Xuejiao; Chen, Yongli; Yin, Jianguo; Xia, Wentang; Yuan, Xiaoli; Xiang, Xiaoyan

2018-06-01

Based on physicochemical properties of the scraps of spent aerospace magnetic materials, a roasting - magnetic separation followed by sulfuric acid leaching process was proposed to extract cobalt. Roasting was performed at 500 °C to remove organic impurity. Non-magnetic impurities were reduced by magnetic separation and then the raw material was sieved into desired particle sizes. Acid leaching was carried out to extract cobalt from the scraps and experimental parameters included agitation speed, particle size, initial concentration of sulfuric acid and temperature. Agitation speed higher than 300 r/min had a relatively small impact on the cobalt extraction. As the particle size reduced, the content of cobalt in the raw material decreases and the extraction of cobalt by acid leaching increased at first and decreased afterwards. Raising the initial concentration of sulfuric acid and temperature contributed to improve the cobalt extraction and the influence of temperature was more remarkable. SEM image revealed that the spent aerospace magnetic materials mainly existed in the sliced strip flake with a loose surface and porous structure. Under the experimental condition, the leaching rate of cobalt from the scraps in sulfuric acid solution could be expressed as ln(-ln(1 - α)) = lnk + nlnt. The apparent activation energy was found to be 38.33 kJ/mol and it was mainly controlled by the surface chemical reaction. Copyright © 2018 Elsevier Ltd. All rights reserved.

Meat waste as feedstock for home composting: Effects on the process and quality of compost.

PubMed

Storino, Francesco; Arizmendiarrieta, Joseba S; Irigoyen, Ignacio; Muro, Julio; Aparicio-Tejo, Pedro M

2016-10-01

Home composting is a powerful tool, which is spreading in different parts of the world, to reduce the generation of municipal waste. However, there is debate concerning the appropriateness, in terms of domestic hygiene and safety, of keeping a composter bin in the household deputed to kitchen waste of animal origin, such as meat or fish scraps and pet droppings. The purpose of our work was to study how the addition of meat scraps to household waste influences the composting process and the quality of the final compost obtained. We compared four raw material mixtures, characterized by a different combination of vegetable and meat waste and different ratios of woody bulking agent. Changes in temperature, mass and volume, phenotypic microbial diversity (by Biolog™) and organic matter humification were determined during the process. At the end of the experiment, the four composts were weighed and characterized by physicochemical analysis. In addition, the presence of viable weed seeds was investigated and a germination bioassay was carried out to determine the level of phytotoxicity. Finally, the levels of pathogens (Escherichia coli and Salmonella spp.) were also determined in the final compost. Here we show that the presence of meat waste as raw feedstock for composting in bins can improve the activity of the process, the physicochemical characteristics and maturity of the compost obtained, without significantly affecting its salinity, pH and phytotoxicity. Pathogen levels were low, showing that they can be controlled by an intensive management and proper handling of the composter bins. Copyright © 2016 Elsevier Ltd. All rights reserved.

Simplex-centroid mixture formulation for optimised composting of kitchen waste.

PubMed

Abdullah, N; Chin, N L

2010-11-01

Composting is a good recycling method to fully utilise all the organic wastes present in kitchen waste due to its high nutritious matter within the waste. In this present study, the optimised mixture proportions of kitchen waste containing vegetable scraps (V), fish processing waste (F) and newspaper (N) or onion peels (O) were determined by applying the simplex-centroid mixture design method to achieve the desired initial moisture content and carbon-to-nitrogen (CN) ratio for effective composting process. The best mixture was at 48.5% V, 17.7% F and 33.7% N for blends with newspaper while for blends with onion peels, the mixture proportion was 44.0% V, 19.7% F and 36.2% O. The predicted responses from these mixture proportions fall in the acceptable limits of moisture content of 50% to 65% and CN ratio of 20-40 and were also validated experimentally. Copyright 2010 Elsevier Ltd. All rights reserved.

Use of scrap tire rubber : state of the technology and best practices.

DOT National Transportation Integrated Search

2005-02-01

The California Department of Transportation (Caltrans) has been using scrap tire rubber (called crumb : rubber modifier (CRM)) in asphalt pavements since the 1970s in chip seals and the 1980s in rubberized : asphalt concrete (RAC). The performance of...

Residents' behaviors, attitudes, and willingness to pay for recycling e-waste in Macau.

PubMed

Song, Qingbin; Wang, Zhishi; Li, Jinhui

2012-09-15

Large quantities of e-waste are presently being generated in Macau, but since recycling facilities and laws on e-waste still need to be developed, most e-waste cannot currently be properly treated. Moreover, little is known about residents' behaviors, attitudes, and their willingness to pay (WTP) for recycling e-waste. These issues are discussed in this study, based on a questionnaire survey on household electronic product usage. In 2010, "Life span completed" was the primary reason respondents abandoned their electronic products, accounting for about 37.97% of responses; the main disposal methods of e-waste in Macau were "Retailers retrieve from consumer" and "Sale to a recycling corporation." While having little understanding of e-waste disposal issues, most residents were still willing to hand their e-waste into the government for centralized collection. In addition, the respondents gave "telephone reservation" as their preferred collection method. Finally, the residents' WTP in Macau was estimated by the logistic regression method. It was found that education level, age and household income were the significant factors affecting residents' WTP. The monthly mean WTP was 20.03MOP (2.50 US dollar) per household, and the annual WTP was approximately 40,185,067 MOP (5,023,133 US dollar) for all of Macau. The results of our study can help managers develop more effective environmental management policies for e-waste disposal. Copyright © 2012 Elsevier Ltd. All rights reserved.

Urban Mining of E-Waste is Becoming More Cost-Effective Than Virgin Mining.

PubMed

Zeng, Xianlai; Mathews, John A; Li, Jinhui

2018-04-17

Stocks of virgin-mined materials utilized in linear economic flows continue to present enormous challenges. E-waste is one of the fastest growing waste streams, and threatens to grow into a global problem of unmanageable proportions. An effective form of management of resource recycling and environmental improvement is available, in the form of extraction and purification of precious metals taken from waste streams, in a process known as urban mining. In this work, we demonstrate utilizing real cost data from e-waste processors in China that ingots of pure copper and gold could be recovered from e-waste streams at costs that are comparable to those encountered in virgin mining of ores. Our results are confined to the cases of copper and gold extracted and processed from e-waste streams made up of recycled TV sets, but these results indicate a trend and potential if applied across a broader range of e-waste sources and metals extracted. If these results can be extended to other metals and countries, they promise to have positive impact on waste disposal and mining activities globally, as the circular economy comes to displace linear economic pathways.

A review on human health consequences of metals exposure to e-waste in China.

PubMed

Song, Qingbin; Li, Jinhui

2015-01-01

As the world's the largest dumping ground for e-waste, much of the population in China is exposed to heavy metals due to informal e-waste recycling processes. We reviewed recent studies on body burdens and human health effects of heavy metals from the major e-waste recycling sites in China. The results showed that the residents in the e-waste recycling sites are facing a potential higher daily intake of heavy metals. Moreover, heavy metals had entered subjects' bodies (the collected 5 tissue samples). Additionally,individual exposure to heavy metals in e-waste has also caused negative health outcomes,especially in neonates and children. We also recorded plausible outcomes associated with exposure to e wast (to heavy metals). A precautionary approach toward exposure, especially in neonates and children, therefore seems warranted.

Informal processing of electronic waste at Agbogbloshie, Ghana: workers' knowledge about associated health hazards and alternative livelihoods.

PubMed

Yu, Emily A; Akormedi, Matthew; Asampong, Emmanuel; Meyer, Christian G; Fobil, Julius N

2017-12-01

This study was conducted to investigate the electronic waste workers' knowledge about the potential health hazards associated with their work as well as the livelihood alternatives that they would prefer if they were given the opportunity. A qualitative cross-sectional study was conducted to gather empirical information on e-waste workers' knowledge about the potential hazards associated with their work and the livelihood alternatives to e-waste recycling with a sample consisting of twenty all-male electronic waste workers at the Agbogbloshie scrap metal yard in Accra, Ghana. Electronic waste workers at Agbogbloshie were found to be exposed to a variety of injuries and illnesses. The workers' knowledge of the association between their health status and their work was generally poor. Apart from the physical injuries, they did not believe their work played any negative role in their health conditions. They preferred occupations such as farming or professional driving located in the northern region of Ghana to be closer to their families. The study concludes that the low knowledge level of the workers on the hazards that are associated with their work has implications for them accepting technologies to protect them and the natural environment from contamination. It is therefore imperative for any intervention to consider the current low level of knowledge and actively educate the workers to raise their awareness level, taking into account the provision of opportunities for workers to acquire applicable skills for future employment in other fields.

Quantifying the Effect of Macroeconomic and Social Factors on Illegal E-Waste Trade.

PubMed

Efthymiou, Loukia; Mavragani, Amaryllis; Tsagarakis, Konstantinos P

2016-08-05

As illegal e-waste trade has been significantly growing over the course of the last few years, the consequences on human health and the environment demand immediate action on the part of the global community. Though it is argued that e-waste flows from developed to developing countries, this subject seems to be more complex than that, with a variety of studies suggesting that income per capita is not the only factor affecting the choice of regions that e-waste is illegally shipped to. How is a country's economic and social development associated with illegal e-waste trade? Is legislation an important factor? This paper aims at quantifying macroeconomic (per capita income and openness of economy) and social (human development and social progress) aspects, based on qualitative data on illegal e-waste trade routes, by examining the percentage differences in scorings in selected indicators for all known and suspected routes. The results show that illegal e-waste trade occurs from economically and socially developed regions to countries with significantly lower levels of overall development, with few exceptions, which could be attributed to the fact that several countries have loose regulations on e-waste trade, thus deeming them attractive for potential illegal activities.

Quantifying the Effect of Macroeconomic and Social Factors on Illegal E-Waste Trade

PubMed Central

Efthymiou, Loukia; Mavragani, Amaryllis; Tsagarakis, Konstantinos P.

2016-01-01

As illegal e-waste trade has been significantly growing over the course of the last few years, the consequences on human health and the environment demand immediate action on the part of the global community. Though it is argued that e-waste flows from developed to developing countries, this subject seems to be more complex than that, with a variety of studies suggesting that income per capita is not the only factor affecting the choice of regions that e-waste is illegally shipped to. How is a country’s economic and social development associated with illegal e-waste trade? Is legislation an important factor? This paper aims at quantifying macroeconomic (per capita income and openness of economy) and social (human development and social progress) aspects, based on qualitative data on illegal e-waste trade routes, by examining the percentage differences in scorings in selected indicators for all known and suspected routes. The results show that illegal e-waste trade occurs from economically and socially developed regions to countries with significantly lower levels of overall development, with few exceptions, which could be attributed to the fact that several countries have loose regulations on e-waste trade, thus deeming them attractive for potential illegal activities. PMID:27527200

Environmental impacts and benefits of state-of-the-art technologies for E-waste management.

PubMed

Ikhlayel, Mahdi

2017-10-01

This study aims to evaluate the environmental impacts and benefits of state-of-the-art technologies for proper e-waste handling using Jordan as a case study. Life Cycle Assessment (LCA) was employed to evaluate five advanced management systems represent state-of-the-art treatment technologies, including sanitary landfilling; proper recycling of metals, materials, and precious metals (PMs); and incineration of plastic and the hazardous portion of printed circuit boards (PCBs). Six e-waste products that contribute the most to the e-waste in Jordan were included in the assessment of each scenario, which resulted in 30 total cases of e-waste management. The findings indicated that landfills for the entire components of the e-waste stream are the worst option and should be avoided. The most promising e-waste management scenario features integrated e-waste processes based on the concept of Integrated Waste Management (IWM), including recycling materials such as non-PMs and PMs, incinerating plastic and the hazardous content of PCBs using the energy recovered from incineration, and using sanitary landfills of residues. For this scenario, the best environmental performance was obtained for the treatment of mobile phones. Incineration of the portion of hazardous waste using energy recovery is an option that deserves attention. Because scenario implementation depends on more than just the environmental benefits (e.g., economic cost and technical aspects), the study proposes a systematic approach founded on the IWM concept for e-waste management scenario selection. Copyright © 2017 Elsevier Ltd. All rights reserved.

Environmental and human exposure to persistent halogenated compounds derived from e-waste in China.

PubMed

Ni, Hong-Gang; Zeng, Hui; Tao, Shu; Zeng, Eddy Y

2010-06-01

Various classes of persistent halogenated compounds (PHCs) can be released into the environment due to improper handling and disposal of electronic waste (e-waste), which creates severe environmental problems and poses hazards to human health as well. In this review, polybrominated diphenyl ethers (PBDEs), polybrominated biphenyls (PBBs), tetrabromobisphenol A (TBBPA), polybrominated phenols (PBPs), polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs), and chlorinated polycyclic aromatic hydrocarbons (ClPAHs) are the main target contaminants for examination. As the world's largest importer and recycler of e-waste, China has been under tremendous pressure to deal with this huge e-waste situation. This review assesses the magnitude of the e-waste problems in China based on data obtained from the last several years, during which many significant investigations have been conducted. Comparative analyses of the concentrations of several classes of toxic compounds, in which e-waste recycling sites are compared with reference sites in China, have indicated that improper e-waste handling affects the environment of dismantling sites more than that of control sites. An assessment of the annual mass loadings of PBDEs, PBBs, TBBPA, PBPs, PCDD/Fs, and ClPAHs from e-waste in China has shown that PBDEs are the dominant components of PHCs in e-waste, followed by ClPAHs and PCDD/Fs. The annual loadings of PBDEs, ClPAHs, and PCDD/Fs emission were estimated to range from 76,200 to 182,000, 900 to 2,000 and 3 to 8 kg/year, respectively. However, PCDD/Fs and ClPAHs should not be neglected because they are also primarily released from e-waste recycling processes. Overall, the magnitude of human exposure to these toxics in e-waste sites in China is at the high end of the global range. Copyright 2010 SETAC.

Bioleaching of Gold and Silver from Waste Printed Circuit Boards by Pseudomonas balearica SAE1 Isolated from an e-Waste Recycling Facility.

PubMed

Kumar, Anil; Saini, Harvinder Singh; Kumar, Sudhir

2018-02-01

Indigenous bacterial strain Pseudomonas balearica SAE1, tolerant to e-waste toxicity was isolated from an e-waste recycling facility Exigo Recycling Pvt. Ltd., India. Toxicity tolerance of bacterial strain was analyzed using crushed (particle size ≤150 µm) waste computer printed circuit boards (PCBs)/liter (L) of culture medium. The EC 50 value for SAE1 was 325.7 g/L of the e-waste pulp density. Two-step bioleaching was then applied to achieve the dissolution of gold (Au) and silver (Ag) from the e-waste. To maximize precious metal dissolution, factors including pulp density, glycine concentration, pH level, and temperature were optimized. The optimization resulted in 68.5 and 33.8% of Au and Ag dissolution, respectively, at a pH of 9.0, a pulp density of 10 g/L, a temperature of 30 °C, and a glycine concentration of 5 g/L. This is the first study of Au and Ag bioleaching using indigenous e-waste bacteria and its analysis to determine e-waste toxicity tolerance.

Assessing resident awareness on e-waste management in Bangalore, India: a preliminary case study.

PubMed

Awasthi, Abhishek Kumar; Li, Jinhui

2018-04-01

The generation of e-waste has increased significantly in India, and the informal recycling of e-waste has adverse effects on environment and public health. In this article, the E-waste management is evaluated in accordance from the resident's awareness perspective in Bangalore city, India. The survey data revealed that about 58% male and 42% female responded and 35% of the participants belong to age range between 18 and 25 years. About 60% of respondent's education level was either graduate or post graduate, 27% high school to higher school, 10% higher educated (> post graduate), and 3% primary to middle. Only 30% of the respondents were confident with e-waste rules and regulation, while 39% of the respondents were of very little information. Indian e-waste management has been improving for the last few years and it continues to develop. Therefore, the findings can be valuable for better understanding the resident's awareness for e-waste management and also need to promote the environmentally sound management of e-waste in Bangalore, India.

Gold biorecovery from e-waste: An improved strategy through spent medium leaching with pH modification.

PubMed

Natarajan, Gayathri; Ting, Yen-Peng

2015-10-01

Rapid technological advancement and relatively short life time of electronic goods have resulted in an alarming growth rate of electronic waste which often contains significant quantities of toxic and precious metals. Compared to conventional recovery methods, bioleaching is an environmentally friendly process for metal extraction. Gold was bioleached from electronic scrap materials (ESM) via gold-cyanide complexation using cyanide produced from pure and mixed cultures of cyanogenic bacteria Chromobacterium violaceum, Pseudomonas aeruginosa and Pseudomonas fluorescens. As ESM was toxic to the bacteria, a two-step bioleaching approach was adopted where the solid waste was added to the bacterial culture after it has reached maximum growth and cyanide production during early stationary phase. Pure culture of C. violaceum showed the highest cyanide production, yielding maximum gold recovery of 11.3% at 0.5% w/v pulp density of ESM in two-step bioleaching. At the same pulp density of ESM, spent medium bioleaching using bacterial cell-free metabolites achieved gold recovery of 18%. Recovery increased to 30% when the pH of the spent medium was increased to shift the equilibrium in favor of cyanide ions production. It is demonstrated for the first time that pH modification of spent medium further improved metal solubilization and yielded higher metal recovery (compared to two-step bioleaching). Copyright © 2015 Elsevier Ltd. All rights reserved.

Gasification of the char derived from distillation of granulated scrap tyres.

PubMed

López, Félix A; Centeno, Teresa A; Alguacil, Francisco José; Lobato, Belén; López-Delgado, Aurora; Fermoso, Javier

2012-04-01

This work reports the effect of pressure on the steam/oxygen gasification at 1000°C of the char derived from low temperature-pressure distillation of granulated scrap tyres (GST). The study was based on the analysis of gas production, carbon conversion, cold gas efficiency and the high heating value (HHV) of the product. For comparison, similar analyses were carried out for the gasification of coals with different rank. In spite of the relatively high ash (≈12 wt.%) and sulphur (≈3 wt.%) contents, the char produced in GST distillation can be regarded as a reasonable solid fuel with a calorific value of 34MJkg(-1). The combustion properties of the char (E(A)≈50 kJ mol(-1)), its temperature of self-heating (≈264°C), ignition temperature (≈459°C) and burn-out temperature (≈676°C) were found to be similar to those of a semi-anthracite. It is observed that the yield, H(2) and CO contents and HHV of the syngas produced from char gasification increase with pressure. At 0.1 MPa, 4.6 Nm(3)kg(char)(-1) of syngas was produced, containing 28%v/v of H(2) and CO and with a HHV around 3.7 MJ Nm(-3). At 1.5 MPa, the syngas yield achieved 4.9N m(3)kg(char)(-1) with 30%v/v of H(2)-CO and HHV of 4.1 MJ Nm(-3). Carbon conversion significantly increased from 87% at 0.1 MPa to 98% at 1.5 MPa. It is shown that the char derived from distillation of granulated scrap tyres can be further gasified to render a gas of considerable heating value, especially when gasification proceeds at high pressure. Copyright © 2011 Elsevier Ltd. All rights reserved.

Blanking Method with Aid of Scrap to Reduce Tensile Residual Stress on Sheared Edge

NASA Astrophysics Data System (ADS)

Yasutomi, T.; Yonemura, S.; Yoshida, T.; Mizumura, M.; Hiwatashi, S.

2017-09-01

A simple shearing method to reduce tensile residual stress on a sheared edge is highly desired in the automotive industry because this type of stress deteriorates the fatigue property of automotive parts. In this study, the effect of a coining method with a shearing scrap material on a sheared edge was investigated. The scrap part of a sheared plate has a fracture surface shape similar to that of the product part since these parts are generated by separation of a single plate with crack propagation. Therefore, it is possible to impose plastic strain over the entire fracture surface by using the scrap part as a coining tool. Effectiveness of this method was investigated for high-tensile-strength steel. Using this method, the tensile residual stress on the sheared surface was significantly reduced and work hardening was slightly increased. The effects of shearing clearance and coining stroke were also investigated. Tensile residual stress decreased as the coining stroke increased; however, it saturated at a certain stroke. The stroke at which tensile residual stress saturated was relatively small at a large clearance. In particular, the amount of plastic deformation on fracture surface increased when coining stroke became large. These tendencies could be explained by the conditions of contact, which were investigated using finite element analysis.

e-Manifest for Hazardous Wastes in Texas

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Texas

e-Manifest for Hazardous Wastes in Arkansas

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Arkansas

e-Manifest for Hazardous Wastes in Louisiana

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Louisiana

e-Manifest for Hazardous Wastes in Oklahoma

EPA Pesticide Factsheets

EPA launches the hazardous waste electronic manifest (e-Manifest) system on June 30, 2018. The fact sheets here are written from EPA's federal perspective but do contain useful information about Oklahoma

Materials in the U.S. Municipal Waste Stream, 1960 to 2012 (in tons)

EPA Pesticide Factsheets

The U.S. Environmental Protection Agency (EPA) has collected and reported data on the generation and disposal of waste in the United States for more than 30 years. We use this information to measure the success of waste reduction and recycling programs across the country. Our trash, or municipal solid waste (MSW), is made up of the things we commonly use and then throw away. These materials include items such as packaging, food scraps, grass clippings, sofas, computers, tires, and refrigerators. MSW does not include industrial, hazardous, or construction waste. The data in Materials and Products in the Municipal Waste Stream, 1960 to 2012, provides estimated data in thousands of tons discarded after recycling and compost recovery for the years 1960, 1970, 1980, 1990, 2000, 2005, 2008, 2010, 2011, and 2012. In this data set, discards include combustion with energy recovery. This data table does not include construction & demolition debris, industrial process wastes, or certain other wastes. Details may not add to totals due to rounding.

Between hype and veracity; privatization of municipal solid waste management and its impacts on the informal waste sector.

PubMed

Sandhu, Kiran; Burton, Paul; Dedekorkut-Howes, Aysin

2017-01-01

The informal waste recycling sector has been an indispensable but ironically invisible part of the waste management systems in developing countries as India, often completely disregarded and overlooked by decision makers and policy frameworks. The turn towards liberalization of economy since 1991 in India opened the doors for privatization of urban services and the waste sector found favor with private companies facilitated by the local governments. In joining the privatization bandwagon, the local governments aim to create an image of a progressive city demonstrated most visibly through apt management of municipal solid waste. Resultantly, the long important stakeholder, the informal sector has been sidelined and left to face the adverse impacts of privatization. There is hardly any recognition of its contributions or any attempt to integrate it within the formal waste management systems. The study investigates the impacts of privatization on the waste pickers in waste recycling operations. Highlighting the other dimension of waste collection and management in urban India the study focuses on the waste pickers and small time informal scrap dealers and this is done by taking the case study of Amritsar city, which is an important historic centre and a metropolitan city in the state of Punjab, India. The paper develops an analytical framework, drawing from literature review to analyze the impacts. In conclusion, it supports the case for involving informal waste sector towards achieving sustainable waste management in the city. Copyright © 2016 Elsevier Ltd. All rights reserved.

AUTOMATED IDENTIFICATION AND SORTING OF RARE EARTH ELEMENTS IN AN E-WASTE RECYCLING STREAM - PHASE I

EPA Science Inventory

Effect of tree thinning and skidding trails on hydrological connectivity in two Japanese forest catchments

NASA Astrophysics Data System (ADS)

López-Vicente, Manuel; Sun, Xinchao; Onda, Yuichi; Kato, Hiroaki; Gomi, Takashi; Hiraoka, Marino

2017-09-01

Land use composition and patterns influence the hydrological response in mountainous and forest catchments. In plantation forest, management operations (FMO) modify the spatial and temporal dynamics of overland flow processes. However, we found a gap in the literature focussed on modelling hydrological connectivity (HC) in plantation forest under different FMO. In this study, we simulated HC in two steep paired forest subcatchments (K2 and K3, 33.2 ha), composed of Japanese cypress (Chamaecyparis obtusa Endl.) and Japanese cedar (Cryptomeria japonica D. Don) plantations (59% of the total area) against a tree thinning intensity of 50% at different time. Additionally, construction of new skidding trails and vegetation recovery was simulated on five thinning-based scenarios that covered a 40-month test period (July 2010 - October 2013). As a future scenario, six check-dams located in the main streams were proposed to reduce sediment and radionuclide delivery. An updated version of Borselli's index of runoff and sediment connectivity was run, using the D-infinity flow accumulation algorithm and exploiting three 0.5-m resolution digital elevation models. On the basis of the pre-FMO scenario, HC increased at catchment scale owing to tree thinning and the new skidding trails. This change was more noticeable within the area affected by the FMO, where HC increased by 11.4% and 10.5% in the cypress and cedar plantations in K2 respectively and by 8.8% in the cedar plantation in K3. At hillslope plot and stream scales, the evolution in the values of HC was less evident, except the increment (by 5.4%) observed in the streams at K2 after the FMO. Progressive vegetation recovery after the FMO triggered a slight reduction of connectivity in all compartments of both subcatchments. Forest roads and especially skidding trails presented the highest values of HC, appearing as the most efficient features connecting the different vegetation patches with the stream network. The spatial

Occupational health hazards related to informal recycling of E-waste in India: An overview.

PubMed

Annamalai, Jayapradha

2015-01-01

The innovation in science and technology coupled with the change in lifestyle of an individual has made an incredible change in the electronic industry show casing an assorted range of new products every day to the world. India too has been impacted by this digital revolution where consumption of electronics goods grows at a rapid rate producing a large amount of waste electrical and electronic equipment. This substantial generation of electronic waste referred to as e-waste accompanied with the lack of stringent environmental laws and regulations for handling the hazardous e-waste has resulted in the cropping of number of informal sectors. Over 95% of the e-waste is treated and processed in the majority of urban slums of the country, where untrained workers carry out the dangerous procedures without personal protective equipment, which are detrimental not only to their health but also to the environment. This paper focuses on the occupational health hazards due to the informal recycling of e-waste and then proceeds to show the safe disposal methods for handling the large quantities of e-waste generated in this electronic era and thus finds a sustainable solution for the formal processing of e-waste.

E-waste: a problem or an opportunity? Review of issues, challenges and solutions in Asian countries.

PubMed

Herat, Sunil; Agamuthu, P

2012-11-01

Safe management of electronic and electrical waste (e-waste/WEEE) is becoming a major problem for many countries around the world. In particular, developing countries face a number of issues with the generation, transboundary movement and management of e-waste. It is estimated that the world generates around 20-50 million tonnes of e-waste annually, most of it from Asian countries. Improper handling of e-waste can cause harm to the environment and human health because of its toxic components. Several countries around the world are now struggling to deal with this emerging threat. Although the current emphasis is on end-of-life management of e-waste activities, such as reuse, servicing, remanufacturing, recycling and disposal, upstream reduction of e-waste generation through green design and cleaner production is gaining much attention. Environmentally sound management (ESM) of e-waste in developing countries is absent or very limited. Transboundary movement of e-waste is a major issue throughout the region. Dealing with the informal recycling sector is a complex social and environmental issue. There are significant numbers of such challenges faced by these countries in achieving ESM of e-waste. This article aims to present a review of challenges and issues faced by Asian countries in managing their e-waste in a sustainable way.

Waste processing: new near infrared technologies for material identification and selection

NASA Astrophysics Data System (ADS)

Cesetti, M.; Nicolosi, P.

2016-09-01

The awareness of environmental issues on a global scale increases the opportunities for waste handling companies. Recovery is set to become all the more important in areas such as waste selection, minerals processing, electronic scrap, metal and plastic recycling, refuse and the food industry. Effective recycling relies on effective sorting. Sorting is a fundamental step of the waste disposal/recovery process. The big players in the sorting market are pushing for the development of new technologies to cope with literally any type of waste. The purpose of this tutorial is to gain an understanding of waste management, frameworks, strategies, and components that are current and emerging in the field. A particular focus is given to spectroscopic techniques that pertains the material selection process with a greater emphasis placed on the NIR technology for material identification. Three different studies that make use of NIR technology are shown, they are an example of some of the possible applications and the excellent results that can be achieved with this technique.

Persistent toxic substances released from uncontrolled e-waste recycling and actions for the future.

PubMed

Man, Ming; Naidu, Ravi; Wong, Ming H

2013-10-01

The Basel Convention on the Control of Transboundary Movement of Hazardous Wastes and their Disposal was adopted on March 22, 1989 and enforced on May 5, 1992. Since then, the USA, one of the world's largest e-waste producers, has not ratified this Convention or the Basel Ban Amendment. Communities are still debating the legal loophole, which permits the export of whole products to other countries provided it is not for recycling. In January 2011, China's WEEE Directive was implemented, providing stricter control over e-waste imports to China, including Hong Kong, while emphasizing that e-waste recycling is the producers' responsibility. China is expected to supersede the USA as the principal e-waste producer, by 2020, according to the UNEP. Uncontrolled e-waste recycling activities generate and release heavy metals and POPs into the environment, which may be re-distributed, bioaccumulated and biomagnified, with potentially adverse human health effects. Greater efforts and scientific approaches are needed for future e-product designs of minimal toxic metal and compound use, reaping greater benefits than debating the definition and handling responsibilities of e-waste recycling. Copyright © 2012 Elsevier B.V. All rights reserved.

Magnesium Recycling of Partially Oxidized, Mixed Magnesium-Aluminum Scrap through Combined Refining and Solid Oxide Membrane Electrolysis Processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiaofei Guan; Peter A. Zink; Uday B. Pal

2012-01-01

Pure magnesium (Mg) is recycled from 19g of partially oxidized 50.5wt.% Mg-Aluminum (Al) alloy. During the refining process, potentiodynamic scans (PDS) were performed to determine the electrorefining potential for magnesium. The PDS show that the electrorefining potential increases over time as the magnesium content inside the Mg-Al scrap decreases. Up to 100% percent of magnesium is refined from the Mg-Al scrap by a novel refining process of dissolving magnesium and its oxide into a flux followed by vapor phase removal of dissolved magnesium and subsequently condensing the magnesium vapor. The solid oxide membrane (SOM) electrolysis process is employed in themore » refining system to enable additional recycling of magnesium from magnesium oxide (MgO) in the partially oxidized Mg-Al scrap. The combination of the refining and SOM processes yields 7.4g of pure magnesium.« less

MUTAGENICITY OF EMISSIONS FROM THE SIMULATED OPEN BURNING OF SCRAP RUBBER TIRES

EPA Science Inventory

The report describes a follow-up to a small-scale combustion study to collect, identify, and quantify products emitted during the simulated open combustion of scrap tires. The initial study found that total estimated emissions of semi-volatile organics ranged from 10 to 50 g/kg o...

Efficient One-Step Electrolytic Recycling of Low-Grade and Post-Consumer Magnesium Scrap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adam C. Powell, IV

2012-07-19

Metal Oxygen Separation Technologies, Inc. (abbreviated MOxST, pronounced most) and Boston University (BU) have developed a new low-cost process for recycling post-consumer co-mingled and heavily-oxidized magnesium scrap, and discovered a new chemical mechanism for magnesium separations in the process. The new process, designated MagReGenTM, is very effective in laboratory experiments, and on scale-up promises to be the lowest-cost lowest-energy lowest-impact method for separating magnesium metal from aluminum while recovering oxidized magnesium. MagReGenTM uses as little as one-eighth as much energy as today's methods for recycling magnesium metal from comingled scrap. As such, this technology could play a vital role inmore » recycling automotive non-ferrous metals, particularly as motor vehicle magnesium/aluminum ratios increase in order to reduce vehicle weight and increase efficiency.« less

From Centralized Disassembly to Life Cycle Management: Status and Progress of E-waste Treatment System in China

NASA Astrophysics Data System (ADS)

Song, Xiaolong; Yang, Jianxin; Lu, Bin; Yang, Dong

2017-01-01

China is now facing e-waste problems from both growing domestic generation and illegal imports. Many stakeholders are involved in the e-waste treatment system due to the complexity of e-waste life cycle. Beginning with the state of the e-waste treatment industry in China, this paper summarizes the latest progress in e-waste management from such aspects as the new edition of the China RoHS Directive, new Treatment List, new funding subsidy standard, and eco-design pilots. Thus, a conceptual model for life cycle management of e-waste is generalized. The operating procedure is to first identify the life cycle stages of the e-waste and extract the important life cycle information. Then, life cycle tools can be used to conduct a systematic analysis to help decide how to maximize the benefits from a series of life cycle engineering processes. Meanwhile, life cycle thinking is applied to improve the legislation relating to e-waste so as to continuously improve the sustainability of the e-waste treatment system. By providing an integrative framework, the life cycle management of e-waste should help to realize sustainable management of e-waste in developing countries.

Occupational health hazards related to informal recycling of E-waste in India: An overview

PubMed Central

Annamalai, Jayapradha

2015-01-01

The innovation in science and technology coupled with the change in lifestyle of an individual has made an incredible change in the electronic industry show casing an assorted range of new products every day to the world. India too has been impacted by this digital revolution where consumption of electronics goods grows at a rapid rate producing a large amount of waste electrical and electronic equipment. This substantial generation of electronic waste referred to as e-waste accompanied with the lack of stringent environmental laws and regulations for handling the hazardous e-waste has resulted in the cropping of number of informal sectors. Over 95% of the e-waste is treated and processed in the majority of urban slums of the country, where untrained workers carry out the dangerous procedures without personal protective equipment, which are detrimental not only to their health but also to the environment. This paper focuses on the occupational health hazards due to the informal recycling of e-waste and then proceeds to show the safe disposal methods for handling the large quantities of e-waste generated in this electronic era and thus finds a sustainable solution for the formal processing of e-waste. PMID:26023273

Characteristics of Indium Tin Oxide (ITO) Nanoparticles Recovered by Lift-off Method from TFT-LCD Panel Scraps.

PubMed

Choi, Dongchul; Hong, Sung-Jei; Son, Yongkeun

2014-11-27

In this study, indium-tin-oxide (ITO) nanoparticles were simply recovered from the thin film transistor-liquid crystal display (TFT-LCD) panel scraps by means of lift-off method. This can be done by dissolving color filter (CF) layer which is located between ITO layer and glass substrate. In this way the ITO layer was easily lifted off the glass substrate of the panel scrap without panel crushing. Over 90% of the ITO on the TFT-LCD panel was recovered by using this method. After separating, the ITO was obtained as particle form and their characteristics were investigated. The recovered product appeared as aggregates of particles less than 100 nm in size. The weight ratio of In/Sn is very close to 91/9. XRD analysis showed that the ITO nanoparticles have well crystallized structures with (222) preferred orientation even after recovery. The method described in this paper could be applied to the industrial recovery business for large size LCD scraps from TV easily without crushing the glass substrate.

Characteristics of Indium Tin Oxide (ITO) Nanoparticles Recovered by Lift-off Method from TFT-LCD Panel Scraps

PubMed Central

Choi, Dongchul; Hong, Sung-Jei; Son, Yongkeun

2014-01-01

In this study, indium-tin-oxide (ITO) nanoparticles were simply recovered from the thin film transistor-liquid crystal display (TFT-LCD) panel scraps by means of lift-off method. This can be done by dissolving color filter (CF) layer which is located between ITO layer and glass substrate. In this way the ITO layer was easily lifted off the glass substrate of the panel scrap without panel crushing. Over 90% of the ITO on the TFT-LCD panel was recovered by using this method. After separating, the ITO was obtained as particle form and their characteristics were investigated. The recovered product appeared as aggregates of particles less than 100 nm in size. The weight ratio of In/Sn is very close to 91/9. XRD analysis showed that the ITO nanoparticles have well crystallized structures with (222) preferred orientation even after recovery. The method described in this paper could be applied to the industrial recovery business for large size LCD scraps from TV easily without crushing the glass substrate. PMID:28788267

Performance outlook of the SCRAP receiver

NASA Astrophysics Data System (ADS)

Lubkoll, Matti; von Backström, Theodor W.; Harms, Thomas M.

2016-05-01

A combined cycle (CC) concentrating solar power (CSP) plant provides significant potential to achieve an efficiency increase and an electricity cost reduction compared to current single-cycle plants. A CC CSP system requires a receiver technology capable of effectively transferring heat from concentrated solar irradiation to a pressurized air stream of a gas turbine. The small number of pressurized air receivers demonstrated to date have practical limitations, when operating at high temperatures and pressures. As yet, a robust, scalable and efficient system has to be developed and commercialized. A novel receiver system, the Spiky Central Receiver Air Pre-heater (SCRAP) concept has been proposed to comply with these requirements. The SCRAP system is conceived as a solution for an efficient and robust pressurized air receiver that could be implemented in CC CSP concepts or standalone solar Brayton cycles without a bottoming Rankine cycle. The presented work expands on previous publications on the thermal modeling of the receiver system. Based on the analysis of a single heat transfer element (spike), predictions for its thermal performance can be made. To this end the existing thermal model was improved by heat transfer characteristics for the jet impingement region of the spike tip as well as heat transfer models simulating the interaction with ambient. While the jet impingement cooling effect was simulated employing a commercial CFD code, the ambient heat transfer model was based on simplifying assumptions in order to employ empirical and analytical equations. The thermal efficiency of a spike under design conditions (flux 1.0 MW/m2, air outlet temperature just below 800 °C) was calculated at approximately 80 %, where convective heat losses account for 16.2 % of the absorbed radiation and radiative heat losses for a lower 2.9 %. This effect is due to peak surface temperatures occurring at the root of the spikes. It can thus be concluded that the geometric

AUTOMATED REMOVAL OF BROMINATED FLAME RETARDANT MATERIAL FROM A MIXED E-WASTE PLASTICS RECYCLING STREAM - PHASE I

EPA Science Inventory

Electronic waste (e-waste) is one of the most rapidly growing waste problems worldwide. Improper handling of e-waste results in vast amounts of toxic waste being sent to landfills and leaching into the water supply. Because of these concerns, e-waste recycling is a rapidly gro...

AUTOMATED REMOVAL OF BROMINATED FLAME RETARDANT MATERIAL FROM A MIXED E-WASTE PLASTICS RECYCLING STREAM - PHASE II

EPA Science Inventory

Electronic waste (e-waste) is one of the most rapidly growing waste problems worldwide. Improper handling of e-waste results in vast amounts of toxic waste being sent to landfill and leaching into the water supply. Due to there concerns e-waste recycling is a rapidly growing...

Soil disturbance and 10-year growth response of coast Douglas-fir on nontilled and tilled skid trails in the Oregon Cascades.

Treesearch

Ronald Heninger; William Scott; Alex Dobkowski; Richard Miller; Harry Anderson; Steve Duke

2002-01-01

We (i) quantified effects of skidder yarding on soil properties and seedling growth in a portion of western Oregon, (ii) determined if tilling skid trails improved tree growth, and (iii) compared results with those from an earlier investigation in coastal Washington. Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) seedlings were hand planted at...

Radiological Characterization Methodology of INEEL Stored RH-TRU Waste from ANL-E

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajiv N. Bhatt

2003-02-01

An Acceptable Knowledge (AK)-based radiological characterization methodology is being developed for RH TRU waste generated from ANL-E hot cell operations performed on fuel elements irradiated in the EBR-II reactor. The methodology relies on AK for composition of the fresh fuel elements, their irradiation history, and the waste generation and collection processes. Radiological characterization of the waste involves the estimates of the quantities of significant fission products and transuranic isotopes in the waste. Methods based on reactor and physics principles are used to achieve these estimates. Because of the availability of AK and the robustness of the calculation methods, the AK-basedmore » characterization methodology offers a superior alternative to traditional waste assay techniques. Using this methodology, it is shown that the radiological parameters of a test batch of ANL-E waste is well within the proposed WIPP Waste Acceptance Criteria limits.« less

Quantification and classification of ship scraping waste at Alang-Sosiya, India.

PubMed

Srinivasa Reddy, M; Basha, Shaik; Sravan Kumar, V G; Joshi, H V; Ghosh, P K

2003-12-01

Alang-Sosiya located on the Western Coast of Gulf of Cambay, is the largest ship recycling yard in the world. Every year on average 365 ships having a mean weight (2.10x10(6)+/-7.82x10(5) LDT) are scrapped. This industry generates a huge quantity of solid waste in the form of broken wood, rubber, insulation materials, paper, metals, glass and ceramics, plastics, leather, textiles, food waste, chemicals, paints, thermocol, sponge, ash, oil mixed sponges, miscellaneous combustible and non-combustible. The quantity and composition of solid waste was collected for a period of three months and the average values are presented in this work. Sosiya had the most waste 15.63 kg/m(2) compared to Alang 10.19 kg/m(2). The combustible solid waste quantity was around 83.0% of the total solid waste available at the yard, which represents an average weight of 9.807 kg/m(2); whereas, non-combustible waste is 1.933 kg/m(2). There is not much difference between the average of total solid waste calculated from the sampling data (96.71 MT/day) and the data provided by the port authorities (96.8 MT/day).

Has the question of e-waste opened a Pandora's box? An overview of unpredictable issues and challenges.

PubMed

Bakhiyi, Bouchra; Gravel, Sabrina; Ceballos, Diana; Flynn, Michael A; Zayed, Joseph

2018-01-01

Despite regulatory efforts and position papers, electrical and electronic waste (e-waste) remains ill-managed as evidenced by the extremely low rates of proper e-waste recycling (e-recycling) worldwide, ongoing illegal shipments to developing countries and constantly reported human health issues and environmental pollution. The objectives of this review are, first, to expose the complexity of e-waste problems, and then to suggest possible upstream and downstream solutions. Exploring e-waste issues is akin to opening a Pandora's box. Thus, a review of prevailing e-waste management practices reveals complex and often intertwined gaps, issues and challenges. These include the absence of any consistent definition of e-waste to date, a prevalent toxic potential still involving already banned or restricted hazardous components such as heavy metals and persistent and bioaccumulative organic compounds, a relentless growth in e-waste volume fueled by planned obsolescence and unsustainable consumption, problematic e-recycling processes, a fragile formal e-recycling sector, sustained and more harmful informal e-recycling practices, and more convoluted and unpredictable patterns of illegal e-waste trade. A close examination of the e-waste legacy contamination reveals critical human health concerns, including significant occupational exposure during both formal and informal e-recycling, and persistent environmental contamination, particularly in some developing countries. However, newly detected e-waste contaminants as well as unexpected sources and environmental fates of contaminants are among the emerging issues that raise concerns. Moreover, scientific knowledge gaps remain regarding the complexity and magnitude of the e-waste legacy contamination, specifically, a comprehensive characterization of e-waste contaminants, information on the scale of legacy contamination in developing countries and on the potential environmental damage in developed countries, and a stronger body

Beneficial reuse `96: The fourth annual conference on the recycle and reuse of radioactive scrap metal

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-02-01

From October 22-24, 1996 the University of Tennessee`s Energy, Environment and Resources Center and the Oak Ridge National Laboratory`s Center for Risk Management cosponsored Beneficial Reuse `96: The Fourth Annual Conference on the Recycle and Reuse of Radioactive Materials. Along with the traditional focus on radioactive scrap metals, this year`s conference included a wide range of topics pertaining to naturally occurring radioactive materials (NORM), and contaminated concrete reuse applications. As with previous Beneficial Reuse conferences, the primary goal of this year`s conference was to bring together stakeholder representatives for presentations, panel sessions and workshops on significant waste minimization issues surroundingmore » the recycle and reuse of contaminated metals and other materials. A wide range of industry, government and public stakeholder groups participated in this year`s conference. An international presence from Canada, Germany and Korea helped to make Beneficial Reuse `96 a well-rounded affair. Selected papers have been processed separately for inclusion in the Energy Science and Technology Database.« less

E-waste: impacts, issues and management strategies.

PubMed

Hussain, Mumtaz; Mumtaz, Saniea

2014-01-01

The present electronic era has seen massive proliferation of electrical and electronic equipment especially during the last two decades. These gadgets have become indispensable components of human life. The gravity of this sensitive 21st century problem is being felt by relevant stakeholders from the community to global level. Consequently, the annual global generation of e-waste is estimated to be 20-50 million tons. According to the Basel Action Network, 500 million computers contain 287 billion kilograms (kg) plastics; 716.7 million kg lead; and 286,700 kg mercury. These gadgets contain over 50 elements from the periodic table. The lethal components include heavy metals (like cadmium, mercury, copper, nickel, lead, barium, hexavalent chromium and beryllium); phosphor; plastics; and brominated flame retardants. These are persistent, mobile, and bioaccumulative toxins that remain in the environment but their forms are changed and are carcinogens, mutagens and teratogens. The ensuing hazardous waste has created deleterious impacts on physical, biological and socioeconomic environments. The lithosphere, hydrosphere, biosphere, and atmosphere of Earth are being gravely polluted. Human beings and other biodiversity face fatal diseases, such as cancer, reproductive disorders, neural damages, endocrine disruptions, asthmatic bronchitis, and brain retardation. Marginal populations of developing countries living in squatter/slums are most vulnerable. Numerous issues are associated with uncontrolled generation, unscientific and environmentally inappropriate recycling processes for the extraction of heavy and precious metals (e.g., gold, platinum, and silver), illegal transboundary shipments from advanced to developing countries and weak conventions/legislations at global and national levels. Although the Basel Convention has been ratified by most countries, illicit trading/trafficking of hazardous substances remains unchecked, sometimes "disguised" as donations. The fact

Relationship between e-waste recycling and human health risk in India: a critical review.

PubMed

Awasthi, Abhishek Kumar; Zeng, Xianlai; Li, Jinhui

2016-06-01

Informal recycling of waste (including e-waste) is an emerging source of environmental pollution in India. Polychlorinated biphenyls (PCBs), polychlorinated diphenyl ethers (PBDEs), and heavy metals, among other substances, are a major health concern for workers engaged in waste disposal and processing, and for residents living near these facilities, and are also a detriment to the natural environment. The main objective of this review article was to evaluate the status of these impacts. The review found that, huge quantity of e-waste/waste generated, only a small amount is treated formally; the remainder is processed through the informal sector. We also evaluated the exposure pathways, both direct and indirect, and the human body load markers (e.g., serum, blood, breast milk, urine, and hair), and assessed the evidence for the association between these markers and e-waste exposure. Our results indicated that the open dumping and informal e-waste recycling systems should be replaced by the best available technology and environmental practices, with proper monitoring and regular awareness programs for workers and residents. Further and more detailed investigation in this area is also recommended.

Technology for High Pure Aluminum Oxide Production from Aluminum Scrap

NASA Astrophysics Data System (ADS)

Ambaryan, G. N.; Vlaskin, M. S.; Shkolnikov, E. I.; Zhuk, A. Z.

2017-10-01

In this study a simple ecologically benign technology of high purity alumina production is presented. The synthesis process consists of three steps) oxidation of aluminum in water at temperature of 90 °C) calcinations of Al hydroxide in atmosphere at 1100 °C) high temperature vacuum processing of aluminum alpha oxide at 1750 °C. Oxidation of aluminum scrap was carried out under intensive mixing in water with small addition of KOH as a catalyst. It was shown that under implemented experimental conditions alkali was continuously regenerated during oxidation reaction and synergistic effect of low content alkali aqueous solution and intensive mixing worked. The product of oxidation of aluminum scrap is the powder of Al(OH)3. Then it can be preliminary granulated or directly subjected to thermal treatment deleting the impurities from the product (aluminum oxide). It was shown the possibility to produce the high-purity aluminum oxide of 5N grade (99.999 %). Aluminum oxide, synthesized by means of the proposed method, meets the requirements of industrial manufacturers of synthetic sapphire (aluminum oxide monocrystals). Obtained high pure aluminum oxide can be also used for the manufacture of implants, artificial joints, microscalpels, high-purity ceramics and other refractory shapes for manufacture of ultra-pure products.

Emerging issue of e-waste in Pakistan: A review of status, research needs and data gaps.

PubMed

Iqbal, Mehreen; Breivik, Knut; Syed, Jabir Hussain; Malik, Riffat Naseem; Li, Jun; Zhang, Gan; Jones, Kevin C

2015-12-01

This review article focuses on the current situation of e-waste in Pakistan with the emphasis on defining the major e-waste recycling sites, current and future domestic generation of e-waste, hidden flows or import of e-waste and discusses various challenges for e-waste management. Needed policy interventions and possible measures to be taken at governmental level are discussed to avoid the increasing problem of e-waste in the country. Our findings highlight that there is still a general lack of reliable data, inventories and research studies addressing e-waste related issues in the context of environmental and human health in Pakistan. There is therefore a critical need to improve the current knowledge base, which should build upon the research experience from other countries which have experienced similar situations in the past. Further research into these issues in Pakistan is considered vital to help inform future policies/control strategies as already successfully implemented in other countries. Copyright © 2015 Elsevier Ltd. All rights reserved.

Urinary heavy metal levels and relevant factors among people exposed to e-waste dismantling.

PubMed

Wang, Hongmei; Han, Mei; Yang, Suwen; Chen, Yanqing; Liu, Qian; Ke, Shen

2011-01-01

Primitive electronic waste (e-waste) recycling has become a growing environmental concern, and toxic heavy metals released from e-waste activities may continue to threaten the health of local people. To study the impact of heavy metals in people around e-waste sites, 349 people from e-waste recycling sites (exposure group) and 118 people from a green plantation (control group) were surveyed, and their urinary levels of lead (UPb), cadmium (UCd), manganese (UMn), copper (UCu), and Zinc (UZn) were assayed. Questionnaire surveys for risk factors were also performed and analyzed by using the Pearson correlation analysis. Results indicated that the levels of urinary Cd in both occupational dismantling people {GM(GSD) 0.72(0.71) ug/L} and non-occupational dismantling people {GM(GSD) 0.50(0.79) ug/L} were higher than the control group {GM(GSD) 0.27(0.85) ug/L}. Further analyses of correlations between urinary heavy metal levels and exposure factors in the exposed group revealed positive relationship between the duration of dismantling and the level of UPb (p < 0.05). Meanwhile, rice sources from local village have a positive correlation with the level of UPb and UCd (p < 0.01). Other factors, however, may also have influences on heavy metal burden, and not all urinary heavy metal levels can be contributed to e-waste dismantling exposure levels. Primitive e-waste recycling activities may contribute to the changes of urinary heavy metal levels and increase the health risk for those chronically working on e-waste dismantling. Copyright © 2010 Elsevier Ltd. All rights reserved.

Investigation of Childhood Lead Poisoning from Parental Take-Home Exposure from an Electronic Scrap Recycling Facility — Ohio, 2012.

PubMed

Newman, Nick; Jones, Camille; Page, Elena; Ceballos, Diana; Oza, Aalok

2015-07-17

Lead affects the developing nervous system of children, and no safe blood lead level (BLL) in children has been identified. Elevated BLLs in childhood are associated with hyperactivity, attention problems, conduct problems, and impairment in cognition. Young children are at higher risk for environmental lead exposure from putting their hands or contaminated objects in their mouth. Although deteriorating lead paint in pre-1979 housing is the most common source of lead exposure in children, data indicate that ≥30% of children with elevated BLLs were exposed through a source other than paint. Take-home contamination occurs when lead dust is transferred from the workplace on employees' skin, clothing, shoes, and other personal items to their car and home. Recycling of used electronics (e-scrap) is a relatively recent source of exposure to developmental neurotoxicants, including lead. In 2010, the Cincinnati Health Department and Cincinnati Children's Hospital Pediatric Environmental Health Specialty Unit (PEHSU) investigated two cases of childhood lead poisoning in a single family. In 2012, CDC's National Institute for Occupational Safety and Health (NIOSH) learned about the lead poisonings during an evaluation of the e-scrap recycling facility where the father of the two children with lead poisoning worked. This report summarizes the case investigation. Pediatricians should ask about parents' occupations and hobbies that might involve lead when evaluating elevated BLLs in children, in routine lead screening questionnaires, and in evaluating children with signs or symptoms of lead exposure.

How much e-waste is there in US basements and attics? Results from a national survey.