Personality Traits of Expert Teachers of Students with EBD: Clarifying a Teacher's X-Factor

ERIC Educational Resources Information Center

Buttner, Svenja; Pijl, Sip Jan; Bijstra, Jan; Van den Bosch, Els

2016-01-01

Teaching students with emotional and behavioural difficulties (EBD) is a challenge for many teachers in inclusive education. Much research has been done to find out what differentiates expert teachers from their less skilled colleagues. Recent evidence points to personality as an underlying core factor influencing teacher performance. In this…

Behavioral Disorders: Practice Concerns and Students with EBD. Advances in Special Education. Volume 23

ERIC Educational Resources Information Center

Bakken, Jeffrey P., Ed.; Obiakor, Festus E., Ed.; Rotatori, Anthony F., Ed.

2012-01-01

Volumes 22 and 23 of the "Advances in Special Education" address the current top perspectives and issues in the field of emotional and behavioral disorders (EBD) by providing chapters written by active researchers and scholarly university professors who specialize in this area. Volume 22 first delineates legal issues, themes, and dimensions…

Enhancement of a culture-based bacterial detection system (eBDS) for platelet products based on measurement of oxygen consumption.

PubMed

Holme, Stein; McAlister, Morven B; Ortolano, Girolamo A; Chong, Chiyong; Cortus, Mary Anne; Jacobs, Michael R; Yomtovian, Roslyn; Freundlich, Lawrence F; Wenz, Barry

2005-06-01

An enhanced bacterial detection system (Pall eBDS) was developed that distinguishes itself from its predecessor (Pall BDS) by removal of the platelet (PLT)-retaining filter allowing for optimal bacterial transfer, modification of the culture tablet to reduce the confounding effects of respiring PLTs while enhancing bacterial growth, and facilitation of nutrients and gas exchange by agitating the sample pouch during incubation at 35 degrees C. The objective was to evaluate the performance of the new eBDS. Leukoreduced whole blood-derived PLT concentrates (LR-PCs) and LR single-donor PLTs (LR-SDPs) were inoculated with 1 to 15 colony-forming units (CFUs) of bacteria per mL in studies of each of 10 bacterial species associated with fatal transfusion-transmitted bacterial infection. Immediately after inoculation and after 24 hours of storage at 22 degrees C, samples of inoculated LR-PCs were aseptically transferred into the eBDS pouches. Pouches were then incubated for 24 hours at 35 degrees C with agitation and oxygen concentration was then measured. Median inoculation levels ranged from 5 to 13 CFUs per mL for each species studied. No significant differences in oxygen concentration were found when comparing LR-PCs with LR-SDPs. When sampling occurred from the PLTs 24 hours after inoculation, all 280 cases (24-33 replicates of each species) were detected as contaminated by the device (100% sensitivity). No false-positives were obtained with 713 uninoculated PLT units. The eBDS demonstrated improved detection sensitivity in the range of 1 to 15 CFUs per mL with no observed false-positives compared to the original BDS (detection range 100 to 500 CFUs/mL) with no false-positives.

Project Baby Care: A Parental Training Program for Students with Emotional and Behavioral Disorders (EBD)

ERIC Educational Resources Information Center

Roberts, Catherine; Wolman, Clara; Harris-Looby, Judy

2004-01-01

Statistics indicate that many victims of fatalities from abuse are children of teenage parents. Profiles of typical abuse perpetrators match the characteristics of many students with emotional and behavioral disorders (EBD) and place them at higher risk of acting impulsively and using violent and abusive behaviors. Teaching students parenting…

Behavior Bingo: The Effects of a Culturally Relevant Group Contingency Intervention for Students with EBD

ERIC Educational Resources Information Center

Collins, Tai A.; Hawkins, Renee O.; Flowers, Emily M.; Kalra, Hilary D.; Richard, Jessie; Haas, Lauren E.

2018-01-01

Students with emotional and behavioral disorders (EBD) have difficulty with academic engagement during independent seatwork tasks. The goal of the current study was to evaluate the effectiveness of Behavior Bingo, a novel interdependent group contingency intervention, on the academic engagement, off-task, and disruptive behavior of students with…

Becoming Warriors: Dramatic Inquiry with 11- to 12-Year-Olds in an EBD Classroom

ERIC Educational Resources Information Center

Edmiston, Brian; Sobjack, Laura

2017-01-01

Using a dialogue format, a college professor and a teacher of 11- to 12-year-old children with emotional and behavioural difficulties (EBD) report on a case study of four children (three boys and a girl) when over a three-week period dramatic inquiry pedagogy (focused on the meaning for students of fictional violent events depicted in extracts…

The Effect of Systematic Academic Instruction on Behavioural and Academic Outcomes of Students with EBD

ERIC Educational Resources Information Center

van der Worp-van der Kamp, Lidy; Pijl, Sip Jan; Post, Wendy J.; Bijstra, Jan O.; van den Bosch, Els J.

2016-01-01

This study aims to assess the impact of systematic academic instruction on academic progress and behavioural problems of students with emotional and/or behavioural disorders (EBD) in special education. Earlier studies have noted the importance of a systematic approach as well as the significance of focusing on academic instruction instead of on…

Understanding Positive and Negative Communication Instances between Special Educators and Parents of High School Students with EBD

ERIC Educational Resources Information Center

Mires, Carolyn B.

2015-01-01

Using a multiple case study methodology, interviews were conducted to examine current practices and perceptions of the communication practices of teachers working with high school students with emotional and behavioral disorders (EBD). These interviews involved questions about general communication instances which occurred each week, communication…

The Effects of Function-Based Self-Advocacy Training on the Problem Behavior, Replacement Behavior, and Self-Advocacy Skills of Students with or at Risk for EBD in General Education Settings

ERIC Educational Resources Information Center

Owens, Tosha Lynn

2017-01-01

Students with emotional and/or behavioral disabilities (EBD) experience some of the greatest challenges among students with disabilities (Kern, Hilt-Panahon, & Sokol, 2009). These students with EBD need access to behavioral support throughout the entire academic setting in order to make progress (Gable et al., 2012), yet few actually receive…

Behavioral Disorders: Identification, Assessment, and Instruction of Students with EBD. Advances in Special Education. Volume 22

ERIC Educational Resources Information Center

Bakken, Jeffrey P., Ed.; Obiakor, Festus E., Ed.; Rotatori, Anthony F., Ed.

2012-01-01

Volumes 22 and 23 of "Advances in Special Education" address the current top perspectives and issues in the field of EBD by providing chapters written by active researchers and scholarly university professors who specialize in this area. Volume 22 first delineates legal issues, themes, and dimensions related to the historical development of the…

What Is Inclusive Didactics? Teachers' Understanding of Inclusive Didactics for Students with EBD in Swedish Mainstream Schools

ERIC Educational Resources Information Center

Gidlund, Ulrika; Boström, Lena

2017-01-01

Including students with emotional and behavioral difficulties (EBD) in general education is one of teachers' greatest challenges and make the dilemma of inclusion displays its most difficult side. This article contributes to the understanding of how teachers in Swedish mainstream schools understand the concept of inclusive didactics for students…

Combining Self-Monitoring and an Interdependent Group Contingency to Improve the Behavior of Sixth Graders with EBD

ERIC Educational Resources Information Center

Denune, Hilary; Hawkins, Renee; Donovan, Lauren; Mccoy, Dacia; Hall, Lyndsie; Moeder, Anthony

2015-01-01

A withdrawal design was used to examine the influence of a self-monitoring procedure on the overall effectiveness of an interdependent group contingency intervention implemented in a sixth-grade classroom in an alternative school serving students with emotional and behavioral disorders (EBD). Dependent variables included student on-task, off-task,…

Relationships of Aggression Subtypes and Peer Status among Aggressive Boys in General Education and Emotional/Behavioral Disorder (EBD) Classrooms

ERIC Educational Resources Information Center

Useche, Ana Carolina; Sullivan, Amanda L.; Merk, Welmoet; Orobio de Castro, Bram

2014-01-01

This study examines the concurrent and longitudinal relationships between reactive and proactive aggression and children's peer status. Participants were 94 Dutch elementary school-aged boys in self-contained special education classrooms for students with emotional/behavioral disorders (EBD) and 47 boys with no disabilities in general education…

SRSD in Practice: Creating a Professional Development Experience for Teachers to Meet the Writing Needs of Students with EBD

ERIC Educational Resources Information Center

McKeown, Debra; FitzPatrick, Erin; Sandmel, Karin

2014-01-01

Self-regulated strategy development (SRSD) is one of the most effective writing interventions (Graham, McKeown, Kiuhara, & Harris, 2012) and has improved the writing skills of students with emotional and behavior disorders (EBD). Practice-based professional development (PBPD) has been effective for teaching participants how to implement SRSD…

Working Successfully towards Inclusion--or Excluding Pupils? A Comparative Retroductive Study of Three Similar Schools in Their Work with EBD

ERIC Educational Resources Information Center

Malmqvist, Johan

2016-01-01

Sweden uses municipally run pupil referral units (PRUs) for students displaying emotional behavioural difficulties (EBD). This study investigates one Swedish municipality where transfers of students to PRUs were related to school practices favouring either inclusion or exclusion. A purposeful sampling procedure was used to select three elementary…

Does the Field of EBD Need a Distinct Set of "Intensive" Interventions or More Systemic Intensity within a Continuum of Social/Emotional Supports?

ERIC Educational Resources Information Center

Lewis, Timothy J.

2016-01-01

The challenges of educating children and youth with intensive social, emotional, and academic needs have been well documented. Students with emotional/ behavioral disorders (EBD) present a range of daily challenges from low intensity, high frequency chronic behaviors such as poor school attendance, disrespect addressed to adults and peers,…

Cost Effectiveness of the Instrumentalism in Occupational Therapy (IOT) Conceptual Model as a Guide for Intervention with Adolescents with Emotional and Behavioral Disorders (EBD)

ERIC Educational Resources Information Center

Ikiugu, Moses N.; Anderson, Lynne

2007-01-01

The purpose of this paper was to demonstrate the cost-effectiveness of using the Instrumentalism in Occupational Therapy (IOT) conceptual practice model as a guide for intervention to assist teenagers with emotional and behavioral disorders (EBD) transition successfully into adulthood. The cost effectiveness analysis was based on a project…

When Universal Approaches and Prevention Services Are Not Enough: The Importance of Understanding the Stigmatization of Special Education for Students with EBD--A Response to Kauffman and Badar

ERIC Educational Resources Information Center

Farmer, Thomas W.

2013-01-01

The author of this commentary responds to an article titled "How We Might Make Special Education for Students with Emotional or Behavioral Disorders Less Stigmatizing," by J.M. Kaufmann and J. Bader, who maintain that identifying youth as having emotional and behavioral disorders (EBD) and providing treatment for them is viewed to be…

Optimization of Evans blue quantitation in limited rat tissue samples

PubMed Central

Wang, Hwai-Lee; Lai, Ted Weita

2014-01-01

Evans blue dye (EBD) is an inert tracer that measures plasma volume in human subjects and vascular permeability in animal models. Quantitation of EBD can be difficult when dye concentration in the sample is limited, such as when extravasated dye is measured in the blood-brain barrier (BBB) intact brain. The procedure described here used a very small volume (30 µl) per sample replicate, which enabled high-throughput measurements of the EBD concentration based on a standard 96-well plate reader. First, ethanol ensured a consistent optic path length in each well and substantially enhanced the sensitivity of EBD fluorescence spectroscopy. Second, trichloroacetic acid (TCA) removed false-positive EBD measurements as a result of biological solutes and partially extracted EBD into the supernatant. Moreover, a 1:2 volume ratio of 50% TCA ([TCA final] = 33.3%) optimally extracted EBD from the rat plasma protein-EBD complex in vitro and in vivo, and 1:2 and 1:3 weight-volume ratios of 50% TCA optimally extracted extravasated EBD from the rat brain and liver, respectively, in vivo. This procedure is particularly useful in the detection of EBD extravasation into the BBB-intact brain, but it can also be applied to detect dye extravasation into tissues where vascular permeability is less limiting. PMID:25300427

Optimization of Evans blue quantitation in limited rat tissue samples

NASA Astrophysics Data System (ADS)

Wang, Hwai-Lee; Lai, Ted Weita

2014-10-01

Evans blue dye (EBD) is an inert tracer that measures plasma volume in human subjects and vascular permeability in animal models. Quantitation of EBD can be difficult when dye concentration in the sample is limited, such as when extravasated dye is measured in the blood-brain barrier (BBB) intact brain. The procedure described here used a very small volume (30 µl) per sample replicate, which enabled high-throughput measurements of the EBD concentration based on a standard 96-well plate reader. First, ethanol ensured a consistent optic path length in each well and substantially enhanced the sensitivity of EBD fluorescence spectroscopy. Second, trichloroacetic acid (TCA) removed false-positive EBD measurements as a result of biological solutes and partially extracted EBD into the supernatant. Moreover, a 1:2 volume ratio of 50% TCA ([TCA final] = 33.3%) optimally extracted EBD from the rat plasma protein-EBD complex in vitro and in vivo, and 1:2 and 1:3 weight-volume ratios of 50% TCA optimally extracted extravasated EBD from the rat brain and liver, respectively, in vivo. This procedure is particularly useful in the detection of EBD extravasation into the BBB-intact brain, but it can also be applied to detect dye extravasation into tissues where vascular permeability is less limiting.

Access to care for children with emotional/behavioral difficulties.

PubMed

Henning-Smith, Carrie; Alang, Sirry

2016-06-01

Emotional/behavioral difficulties (EBDs) are increasingly diagnosed in children, constituting some of the most common chronic childhood conditions. Left untreated, EBDs pose long-term individual and population-level consequences. There is a growing evidence of disparities in EBD prevalence by various demographic characteristics. This article builds on this research by examining disparities in access to medical care for children with EBD. From 2008 to 2011, using data from the US National Health Interview Survey (N = 31,631) on sample children aged 4-17, we investigate (1) whether having EBD affects access to care (modeled as delayed care due to cost and difficulty making an appointment) and (2) the role demographic characteristics, health insurance coverage, and frequency of service use play in access to care for children with EBD. Results indicate that children with EBD experience issues in accessing care at more than twice the rate of children without EBD, even though they are less likely to be uninsured than their counterparts without EBD. In multivariable models, children with EBD are still more likely to experience delayed care due to cost and difficulty making a timely appointment, even after adjusting for frequency of health service use, insurance coverage, and demographic characteristics. © The Author(s) 2015.

Access to care for children with emotional/behavioral difficulties

PubMed Central

Henning-Smith, Carrie; Alang, Sirry

2014-01-01

Emotional/behavioral difficulties (EBD) are increasingly diagnosed in children, constituting some of the most common chronic childhood conditions. Left untreated, EBD pose long-term individual and population-level consequences. There is growing evidence of disparities in EBD prevalence by various demographic characteristics. This paper builds on this research by examining disparities in access to medical care for children with EBD. Using data on sample children aged 4-17 from 2008-2011 of the United States National Health Interview Survey (n=29,493), we investigate: 1. Whether having EBD affects access to care (modeled as delayed care due to cost and difficulty making an appointment); and 2. The role demographic characteristics, health insurance coverage, and frequency of service use play in access to care for children with EBD. Results indicate that children with EBD experience issues in accessing care at more than twice the rate of children without EBD, even though they are less likely to be uninsured than their counterparts without EBD. In multivariable models, children with EBD are still more likely to experience delayed care due to cost and difficulty making a timely appointment, even after adjusting for frequency of health service use, insurance coverage, and demographic characteristics. PMID:25583944

Glass-Based Transparent Conductive Electrode: Its Application to Visible-to-Ultraviolet Light-Emitting Diodes.

PubMed

Lee, Tae Ho; Kim, Kyeong Heon; Lee, Byeong Ryong; Park, Ju Hyun; Schubert, E Fred; Kim, Tae Geun

2016-12-28

Nitride-based ultraviolet light-emitting diodes (UV LEDs) are promising replacements for conventional UV lamps. However, the external quantum efficiency of UV LEDs is much lower than for visible LEDs due to light absorption in the p-GaN contact and electrode layers, along with p-AlGaN growth and doping issues. To minimize such absorption, we should obtain direct ohmic contact to p-AlGaN using UV-transparent ohmic electrodes and not use p-GaN as a contact layer. Here, we propose a glass-based transparent conductive electrode (TCE) produced using electrical breakdown (EBD) of an AlN thin film, and we apply the thin film to four (Al)GaN-based visible and UV LEDs with thin buffer layers for current spreading and damage protection. Compared to LEDs with optimal ITO contacts, our LEDs with AlN TCEs exhibit a lower forward voltage, higher light output power, and brighter light emission for all samples. The ohmic transport mechanism for current injection and spreading from the metal electrode to p-(Al)GaN layer via AlN TCE is also investigated by analyzing the p-(Al)GaN surface before and after EBD.

Do Adolescents with Emotional and Behavioral Disturbances Attending Schools for Special Education Have Lower Expectations Regarding the Transition to Adulthood?

ERIC Educational Resources Information Center

Margraf, Hannah; Pinquart, Martin

2016-01-01

Individuals with emotional and behavioral disturbances (EBD) and those attending special schools tend to have poorer adult outcomes than adolescents without EBD and peers from regular schools. Using a four-group comparison (students with or without EBD from special schools and students with or without EBD from regular schools), the present study…

Impact of Evidence-Based Dentistry Workshops on Educators' Use of Evidence in Teaching and Practice: A Pilot Study.

PubMed

Moreira, Narjara C F; Leonardi-Dutra, Kamile; Feres, Murilo F N; Colangelo, Erica A M; Balevi, Ben; Matthews, Debora; Flores-Mir, Carlos

2018-06-01

The aims of this pilot study were to evaluate the short-term impact of evidence-based dentistry (EBD) workshops on educators' use of clinical evidence in their clinical practice and educational activities and to identify barriers they encountered in implementing evidence in their teaching and clinical practice. Between April 2012 and January 2014, a series of EBD workshops was delivered to 31 dental faculty members and postdoctoral students at three Canadian dental schools. Survey I, assessing participants' perceptions of various aspects of the workshops, was administered immediately following the workshops. Survey II, evaluating the impact of the workshops on participants' EBD implementation, was conducted 10 to 31 months after their completion. Survey I was completed by all 31 participants (100% response rate); their mean scores ranged from 3.94 to 4.65 on a five-point scale. Survey II was completed by 20 participants (64.5% response rate; five postdoctoral students and 15 faculty members), using an online 20-item questionnaire. Of the respondents, 19 (95%) reported implementing EBD in their professional activities at that time, and 14 (70%) stated that the workshops had positively helped with EBD implementation. Eight respondents (40%) reported having experienced barriers to EBD implementation, while 15 (75%) reported that their patients/students welcomed use of EBD. The respondents reported believing that strategies such as increasing EBD education and dissemination and improving quality and accessibility of evidence would facilitate the transition to EBD practice. Reported barriers to EBD implementation included resistance and criticism from colleagues, difficulty in changing current practice model, and lack of time.

The winds of change revisited: progress towards building a culture of evidence-based dentistry.

PubMed

Hinton, Robert J; McCann, Ann L; Schneiderman, Emet D; Dechow, Paul C

2015-05-01

In 2008, Texas A&M University Baylor College of Dentistry launched a comprehensive four-year curriculum in evidence-based dentistry (EBD) along with a series of faculty development initiatives to create an EBD culture. The aim of this study was to determine the institution's success in achieving this goal. The assessment tool used was the PEAK instrument, which measures respondents' EBD Practices, Experience, Attitudes, and Knowledge. Two EBD-trained classes of students and one class untrained in EBD (approximately 100 students in each class) were assessed annually. The faculty were assessed before and after completion of the initiative. Nearly all students responded, with samples ranging from 87 to 102; the faculty response rates were 53% (62/117) in 2009 and 66% in 2013 (81/123). In the results, the trained students scored significantly higher in knowledge than the untrained students at each of the first three PEAK administrations (p≤0.001). Regarding confidence in appraising a research report, the first trained group significantly gained in appropriate use of statistical tests (p<0.001), while the second trained group significantly gained in this aspect and five others (p≤0.032). At the final PEAK administration, the second trained group agreed more than the untrained group that EBD was important for the practice of dentistry (p<0.001). Faculty comfort level with reading peer-reviewed articles increased significantly from 2009 to 2013 (p=0.039). Faculty members who participated in the summer EBD Fundamentals course (n=28) had significantly higher EBD knowledge scores than those who did not participate (p=0.013), and their EBD attitudes and practices were more positive (p<0.05). Students and faculty trained in EBD were more knowledgeable and exhibited more positive attitudes, supporting a conclusion that the college has made substantial progress towards achieving an EBD culture.

The Winds of Change Revisited: Progress Towards Building a Culture of Evidence-Based Dentistry

PubMed Central

Hinton, Robert J.; McCann, Ann L.; Schneiderman, Emet D.; Dechow, Paul C.

2016-01-01

In 2008, Texas A&M University Baylor College of Dentistry launched a comprehensive four-year curriculum in evidence-based dentistry (EBD) along with a series of faculty development initiatives to create an EBD culture. The aim of this study was to determine the institution's success in achieving this goal. The assessment tool used was the PEAK instrument, which measures respondents’ EBD Practices, Experience, Attitudes, and Knowledge. Two EBD-trained classes of students and one class untrained in EBD (approximately 100 students in each class) were assessed annually. The faculty were assessed before and after completion of the initiative. Nearly all students responded, with samples ranging from 87 to 102; the faculty response rates were 53% (62/117) in 2009 and 66% in 2013 (81/123). In the results, the trained students scored significantly higher in knowledge than the untrained students at each of the first three PEAK administrations (p≤0.001). Regarding confidence in appraising a research report, the first trained group significantly gained in appropriate use of statistical tests (p<0.001), while the second trained group significantly gained in this aspect and five others (p≤0.032). At the final PEAK administration, the second trained group agreed more than the untrained group that EBD was important for the practice of dentistry (p<0.001). Faculty comfort level with reading peer-reviewed articles increased significantly from 2009 to 2013 (p=0.039). Faculty members who participated in the summer EBD Fundamentals course (n=28) had significantly higher EBD knowledge scores than those who did not participate (p=0.013), and their EBD attitudes and practices were more positive (p<0.05). Students and faculty trained in EBD were more knowledgeable and exhibited more positive attitudes, supporting a conclusion that the college has made substantial progress towards achieving an EBD culture. PMID:25941143

Librarians' roles in evidence-based dentistry education: a review of literature and a survey in North America.

PubMed

Gu, Xiao-Mei

2010-10-01

This study describes the current roles of dental librarians in Evidence-based Dentistry (EBD) education including their perceptions of EBD and barriers to their involvement. A Web-based survey was distributed to the dental librarians in North America, with a 71% response rate. The results showed that the majority of dental librarians are playing multiple and diverse roles in EBD education. The most frequently cited barrier to their involvement is the low level of interest from the dental faculty/student/school. Most dental librarians felt competent in supporting EBD, although continuing education needs in both EBD and teaching skills were pointed out.

Endoscopic versus Percutaneous Biliary Drainage in Palliation of Advanced Malignant Hilar Obstruction: A Meta-Analysis and Systematic Review

PubMed Central

Dharmapuri, Sirish; Duvvuri, Abhiram; Dharmapuri, Sowmya; Boddireddy, Raghuveer; Moole, Vishnu; Yedama, Prathyusha; Bondalapati, Naveen; Uppu, Achuta

2016-01-01

Background. Palliation in advanced unresectable hilar malignancies can be achieved by endoscopic (EBD) or percutaneous transhepatic biliary drainage (PTBD). It is unclear if one approach is superior to the other in this group of patients. Aims. Compare clinical outcomes of EBD versus PTBD. Methods. (i) Study Selection Criterion. Studies using PTBD and EBD for palliation of advanced unresectable hilar malignancies. (ii) Data Collection and Extraction. Articles were searched in Medline, PubMed, and Ovid journals. (iii) Statistical Method. Fixed and random effects models were used to calculate the pooled proportions. Results. Initial search identified 786 reference articles, in which 62 articles were selected and reviewed. Data was extracted from nine studies (N = 546) that met the inclusion criterion. The pooled odds ratio for successful biliary drainage in PTBD versus EBD was 2.53 (95% CI = 1.57 to 4.08). Odds ratio for overall adverse effects in PTBD versus EBD groups was 0.81 (95% CI = 0.52 to 1.26). Odds ratio for 30-day mortality rate in PTBD group versus EBD group was 0.84 (95% CI = 0.37 to 1.91). Conclusions. In patients with advanced unresectable hilar malignancies, palliation with PTBD seems to be superior to EBD. PTBD is comparable to EBD in regard to overall adverse effects and 30-day mortality. PMID:27648439

Medicating Students with Emotional and Behavioral Disorders and ADHD: A State Survey.

ERIC Educational Resources Information Center

Runnheim, Veronica A.; And Others

1996-01-01

Wisconsin teachers provided information on 1,300 students with emotional and behavioral disorders (EBD) who were receiving medication for attention deficit hyperactivity disorder (ADHD). The ADHD/EBD students comprised approximately 26% of all EBD students. The most common medication was Ritalin, and teachers believed the medication effectively…

Libyan Children's Views on the Importance of School Factors Which Contributed to Their Emotional and Behavioral Difficulties

ERIC Educational Resources Information Center

Gadour, Abdelbasit

2006-01-01

A group of 34 children from mainstream schools in Libya representing four Local Education Authorities (LEAs) were interviewed about their emotional and behavioral difficulties (EBD) and the factors which might be responsible for their EBD. Although, in general, children's views of EBD did not yield remarkably different accounts to those already…

An Idea for the Future of Dental Research: A Cloud-Based Clinical Network and Database

ERIC Educational Resources Information Center

Owtad, Payam; Taichman, Russell; Park, Jae Hyun; Yaibuathes, Sorn; Knapp, John

2013-01-01

Evidence-based dentistry (EBD) is an approach to oral healthcare requiring systematic assessment of relevant scientific evidence to clinical practice and patients' needs. EBD attempts to globally establish personalized dental care based upon the most recent and highest order scientific evidence. However, some times the EBD does not consider local…

Lost in translation: bridging gaps between design and evidence-based design.

PubMed

Watkins, Nicholas; Keller, Amy

2008-01-01

The healthcare design community is adopting evidence-based design (EBD) at a startling rate. However, the role of research within an architectural practice is unclear. Reasons for the lack of clarity include multiple connotations of EBD, the tension between a research-driven market and market-driven research, and the competing expectations and standards of design practitioners and researchers. Research as part of EBD should be integral with the design process so that research directly contributes to building projects. Characteristics of a comprehensive programming methodology to close the gap between design and EBD are suggested.

Towards Systemic Support of Pupils with Emotional and Behavioural Disorders

ERIC Educational Resources Information Center

Mooij, Ton; Smeets, Ed

2009-01-01

Children with emotional and behavioural disorders (EBD) vary in many respects. In school, specific conditions have to be fulfilled in order to deal adequately with EBD. This study addresses the question how mainstream primary schools design different instructional situations to support pupils with EBD in practice, and how this design could be…

Emotional and Behavioral Disorders in South Korea: Current Status and Issues

ERIC Educational Resources Information Center

Kim, Joungmin; Kim, Kyeong-hwa

2016-01-01

In South Korea, there is no consensus on the definition of emotional and behavioral disorders (EBD). This column focuses on how the definition has affected the prevalence rates and services available for students with EBDs. Of the legal, clinical, and educational definitions, the legal definition of EBDs is currently in common use, which raises…

Integrating critical thinking and evidence-based dentistry across a four-year dental curriculum: a model for independent learning.

PubMed

Marshall, Teresa A; Straub-Morarend, Cheryl L; Handoo, Nidhi; Solow, Catherine M; Cunningham-Ford, Marsha A; Finkelstein, Michael W

2014-03-01

Introducing critical thinking and evidence-based dentistry (EBD) content into an established dental curriculum can be a difficult and challenging process. Over the past three years, the University of Iowa College of Dentistry has developed and implemented a progressive four-year integrated critical thinking and EBD curriculum. The objective of this article is to describe the development and implementation process to make it available as a model for other dental schools contemplating introduction of critical thinking and EBD into their curricula. The newly designed curriculum built upon an existing problem-based learning foundation, which introduces critical thinking and the scientific literature in the D1 year, in order to expose students to the rationale and resources for practicing EBD in the D2 and D3 years and provide opportunities to practice critical thinking and apply the EBD five-step process in the D2, D3, and D4 years. All curricular content is online, and D3 and D4 EBD activities are integrated within existing clinical responsibilities. The curricular content, student resources, and student activities are described.

Development of an experimental model of cholestasis induced by hypoxic/ischemic damage to the bile duct and liver tissues in infantile rats.

PubMed

Toki, Fumiaki; Takahashi, Atsushi; Suzuki, Makoto; Ootake, Sayaka; Hirato, Junko; Kuwano, Hiroyuki

2011-05-01

We aimed to develop experimental models of hypoxia/ischemia-induced cholestasis using neonatal and infantile rats. Hypoxia/ischemia was induced in the bile duct (BD) by injecting prostaglandin (PG) at birth and/or by coagulation of the hepatic artery (CHA) at about 3 weeks after birth. The rats were divided into 6 groups: control; PG-injected; sham-operated with or without PG; CHA; and CHA + PG. CHA was also performed in adult rats. Liver specimens and blood samples were obtained at 5 weeks after birth, and immunohistochemical and biochemical examinations were performed. (1) BD proliferation with fibrosis (BDPF) was found in the intrahepatic portal tract in the CHA and CHA + PG groups. Low-grade BDPF was observed in the PG group. (2) Cyst formation in the extrahepatic BD (EBD) was observed in the porta hepatis of some rats in the CHA and CHA + PG groups. In these groups, the number of peribiliary vascular plexuses (PVPs) decreased. BD proliferation and infiltration of inflammatory cells were observed in the EBD wall in the CHA + PG group. (3) Ki-67 was expressed in BD and EBD cells in the CHA + PG group. (4) BDPF was not detected in adult rats with CHA. (5) Serum liver function tests indicated obstructive changes in the EBD in the CHA and CHA + PG groups. Reduced blood flow in the EBD during infancy induced BDPF and obstructive changes in the EBD, which may, along with immature PVP and inflammatory changes in the EBD, contribute to hypoxia/ischemia of the EBD.

Repair of extrahepatic bile duct defect using a collagen patch in a Swine model.

PubMed

Tao, Liang; Li, Qiang; Ren, Haozhen; Chen, Bing; Hou, Xianglin; Mou, Lingjun; Zhou, Siqiao; Zhou, Jianxin; Sun, Xitai; Dai, Jianwu; Ding, Yitao

2015-04-01

Extrahepatic bile duct (EBD) injury can happen during surgery. To repair a defect of the EBD and prevent postoperative biliary complications, a collagen membrane was designed. The collagen material was porous, biocompatible, and degradable and could maintain its shape in bile soaking for about 4 weeks. The goal was to induce rapid bile duct tissue regeneration. Twenty Chinese experimental hybrid pigs were used in this study and divided into a patch group and a control group. A spindle-shaped defect (20 mm × 6 mm) was made in the anterior wall of the lower EBD in the swine model, and then the defect was reconstructed using a collagen patch with a drainage tube and wrapped with greater omentum. Ultrasound was performed at 2, 4, 8, and 12 weeks postoperatively. Liver function tests and white blood cell count (WBC) were measured. Hematoxylin-eosin staining, cytokeratin 7 immunohistochemical staining, and Van Gieson's staining of EBD were used. The diameter and thickness of the EBD at the graft site were measured. There was no significant difference in liver function tests or WBC in the patch group compared with the control group. No evidence of leakage or stricture was observed, but some pigs developed biliary sludge or stone at 4 and 8 weeks. The drainage tube was lost within 12 weeks. The neo-EBD could withstand normal biliary pressure 2 weeks after surgery. Histological study showed the accessory glands and epithelial cells gradually regenerated at graft sites from 4 weeks, with increasing vessel infiltration and decreasing inflammation. The collagen fibers became regular with full coverage of epithelial cells. The statistical analysis of diameter and thickness showed no stricture formation at the graft site, but the EBD wall was slightly thicker than in the normal bile duct due to collagen fiber deposition. The structure of the neo-EBD was similar to that of the normal EBD. The collagen membrane patch associated with a drainage tube and wrapped with greater

Endoscopic balloon dilatation of Crohn's disease strictures: results from a large United kingdom series.

PubMed

Bhalme, Mahesh; Sarkar, Sanchoy; Lal, Simon; Bodger, Keith; Baker, Rose; Willert, Robert P

2014-02-01

Stricturing is a common complication of Crohn's disease. Endoscopic balloon dilatation (EBD) offers a valuable alternative to surgical intervention, but there are limited data on factors influencing its safety and efficacy. A multicenter retrospective audit across 4 U.K. teaching hospitals was performed on the use of EBD for Crohn's strictures between 1998 and 2011. Demographics, smoking status, medications, C-reactive protein, endoscopic findings, and subsequent surgery at follow-up were recorded. Success of EBD was defined as symptomatic improvement without the need for surgery at follow-up. Seventy-nine patients (47 women; median age, 48 yr) were identified for this study. Forty-eight (61%) patients had ileocolonic anastomotic strictures, whereas the rest had de novo strictures. In total, 191 EBDs (range, 1-11; median 2) were carried out on 93 strictures (range, 1-5; median 1) over a median duration of 12 months (range, 1-84). There were no serious adverse events. Success at index EBD was 34%, with a further 43% achieving long-term benefit from additional EBDs. Eighteen (23%) patients required surgery. Time to surgery after the first EDB was 2.6 to 71.1 months (median, 12.8 mo). Longer Crohn's disease duration (P = 0.03) and high C-reactive protein (P = 0.008) were associated with an increased need for subsequent surgery. EBD was safe and effective in achieving long-term symptom improvement and avoidance of surgery in most patients. Prospective controlled trials are needed to evaluate the effect of other factors, including Crohn's disease phenotype, and the role of concomitant medication to identify those best suited to EBD.

Is Heller myotomy better than balloon dilation? A meta-analysis.

PubMed

Illés, Anita; Farkas, Nelli; Hegyi, Péter; Garami, András; Szabó, Imre; Solymár, Margit; Pétervári, Erika; Balaskó, Márta; Pár, Gabriella; Sarlós, Patrícia; Bajor, Judit; Szűcs, Ákos; Czimmer, József; Szemes, Kata; Vincze, Áron

2017-06-01

Endoscopic balloon dilation (EBD) and laparoscopic Heller myotomy (LHM) are the most commonly performed treatment options for achalasia. Decision between these treatment options is difficult. The aim of this meta-analysis was to evaluate the efficacy of EBD compared to LHM. The electronic databases PubMed, Embase and Cochrane Controlled Trials Registry were systematically searched for the period between January 1, 1976 and December 31, 2015. Meta-analysis was performed using the PICOS (problem, intervention, comparison, outcome, study design) format. Efficacy and safety of EBD were compared to LHM. Forest plot analyses were used to illustrate the success rate, perforation rate and post-procedural gastroesophageal reflux. Using the search strategy, eight studies met the selection criteria and were included in the meta-analysis. The total number of patients included was 749 (360 in the EBD group and 389 in the LHM group). The success rate was lower in the EBD group than in the LHM group (OR=0.486; CI: 0.304-0.779; p=0.003). The rate of perforation did not differ significantly between the EBD and LHM group (RR= 0.635, CI: 0.340-1.186, p=0.154). The incidence of post-procedural symptomatic gastroesophageal reflux did not differ between the two treatment groups (RR=0.663, CI: 0.328-1.343, p=0.254). Our data suggest that the efficacy of LHM is superior to that of EBD, while there is no difference in safety between the two treatment groups.

Potential Usefulness of the Kampo Medicine Yokukansan, Containing Uncaria Hook, for Paediatric Emotional and Behavioural Disorders: A Case Series

PubMed Central

2013-01-01

Background. Paediatric emotional and behavioural disorders (EBD) are relatively common diseases. Although nonpharmacologic and pharmacologic treatments are utilized in these cases, it is sometimes difficult to manage the symptoms of EBD. Historically, Uncaria hook has been used for treating nighttime crying and convulsions in children. Recent clinical studies have demonstrated that the Kampo medicine Yokukansan (YKS), which contains Uncaria hook, is efficacious for behaviour disorders in Alzheimer's disease patients. Herein, we investigated the clinical efficacy and safety of YKS in a series of cases with paediatric EBD. Patients and Methods. We retrospectively reviewed all paediatric patients who sought Japanese Kampo therapy at our outpatient clinics between April 1, 2012, and April 30, 2013; we selected patients who were diagnosed with paediatric EBD and were treated with YKS. Results. After screening all candidates, 3 patients were eligible for this analysis. Their average age was 11.6 years (range 10–13 years). All 3 patients responded very well to YKS within 1 month. No drug-related adverse events were observed during the course of YKS treatment. Conclusion. Yokukansan may be efficacious for paediatric EBD. We believe these results warrant further evaluation of the clinical efficacy and safety of Yokukansan for paediatric EBD in a carefully designed, double-blind, randomized clinical study. PMID:24204394

Effects of Streptomycin Administration on Increases in Skeletal Muscle Fiber Permeability and Size Following Eccentric Muscle Contractions.

PubMed

Hayao, Keishi; Tamaki, Hiroyuki; Nakagawa, Kouki; Tamakoshi, Keigo; Takahashi, Hideaki; Yotani, Kengo; Ogita, Futoshi; Yamamoto, Noriaki; Onishi, Hideaki

2018-06-01

The purpose of this study was to investigate the preventive effect of streptomycin (Str) administration on changes in membrane permeability and the histomorphological characteristics of damaged muscle fibers following eccentric contraction (ECC ). Eighteen 7-week-old male Fischer 344 rats were randomly assigned to three groups: control (Cont), ECC, and ECC with Str (ECC + Str). The tibialis anterior (TA) muscles in both ECC groups were stimulated electrically and exhibited ECC. Evans blue dye (EBD), a marker of muscle fiber damage associated with increased membrane permeability, was injected 24 hr before TA muscle sampling. The number of EBD-positive fibers, muscle fiber cross-sectional area (CSA), and roundness were determined via histomorphological analysis. The ECC intervention resulted in an increased fraction of EBD-positive fibers, a larger CSA, and decreased roundness. The fraction of EBD-positive fibers was 79% lower in the ECC + Str group than in the ECC group. However, there was no difference in the CSA and roundness of the EBD-positive fibers between the two ECC groups. These results suggest that Str administration can reduce the number of myofibers that increase membrane permeability following ECC, but does not ameliorate the extent of fiber swelling in extant EBD-positive fibers. Anat Rec, 301:1096-1102, 2018. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

Assessment of knowledge, attitude, and practice with regard to evidence-based dentistry among dental students in Isfahan University of Medical Sciences

PubMed Central

Eslamipour, Faezeh; Ghaiour, Marzieh

2016-01-01

Aim: Evidence-based dentistry (EBD) is an approach to oral health that requires the application and examination of relevant scientific data related to the patient's oral health and his priorities. The aim of this study was to assess knowledge, attitude, and practice of dental students of Isfahan about EBD. Materials and Methods: In this descriptive study, 168 dental students in 3 final years of their education who engaged in clinical practice by consensus sampling were recruited. For data collection, a validated questionnaire was used. The questionnaire was consisted of demographic questions and some questions about four issues: Knowledge of self-assess (KSA), evidence-based practice, actual knowledge and attitude about EBD. Data were analyzed with t-test, one-way ANOVA, Chi-square, and linear regression with SPSS 16. Results: One hundred and thirty-six students from 168 students were filled the questionnaire. The mean of KSA was 13 ± 4.3, mean of usage of useful references in EBD was 16.9 ± 7.6. One-third of students were studied their last article in last 6 months before. The mean of actual knowledge and attitude was 7.4 ± 2.3 and 24 ± 3.8, respectively. The relation between 4 main issues was significant (P < 0.05). Conclusion: By considering overall interest and positive attitude toward learning EBD in dental students, it is highly recommended that practical educational courses about EBD be planned by dental faculties. PMID:27500165

Investigation of a Multi-Component Intervention Addressing Mathematical Reasoning and Self-Regulation of Behavior for Students with Emotional/Behavioral Disabilities

ERIC Educational Resources Information Center

Fisher, Marie B.

2013-01-01

For students with Emotional/Behavioral Disabilities (EBD), negative student outcomes are the poorest across disability categories, including high rates of school dropouts, unemployment and incarcerations. Mathematically, students with EBD receiving instruction in special education settings experience practices not consistent with recommendations…

A Comparison of Systematic Screening Tools for Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Lane, Kathleen Lynne; Little, M. Annette; Casey, Amy M.; Lambert, Warren; Wehby, Joseph; Weisenbach, Jessica L.; Phillips, Andrea

2009-01-01

Early identification of students who might develop emotional and behavioral disorders (EBD) is essential in preventing negative outcomes. Systematic screening tools are available for identifying elementary-age students with EBD, including the "Systematic Screening for Behavior Disorders" (SSBD) and the "Student Risk Screening…

Examining the Effectiveness of Numbered Heads Together for Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Hunter, William; Haydon, Todd

2013-01-01

Challenging behaviors displayed in both general education classrooms and self-contained classrooms by students with emotional behavioral disorders (EBD) can be a difficult challenge for novice and experienced teachers (Kennedy & Jolivette, 2008; Turnbull, Turnbull, & Wehmeyer, 2010). Furthermore, students with EBD demonstrate broad…

Sparkling extreme-ultraviolet bright dots observed with Hi-C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Régnier, S.; Alexander, C. E.; Walsh, R. W.

Observing the Sun at high time and spatial scales is a step toward understanding the finest and fundamental scales of heating events in the solar corona. The high-resolution coronal (Hi-C) instrument has provided the highest spatial and temporal resolution images of the solar corona in the EUV wavelength range to date. Hi-C observed an active region on 2012 July 11 that exhibits several interesting features in the EUV line at 193 Å. One of them is the existence of short, small brightenings 'sparkling' at the edge of the active region; we call these EUV bright dots (EBDs). Individual EBDs havemore » a characteristic duration of 25 s with a characteristic length of 680 km. These brightenings are not fully resolved by the SDO/AIA instrument at the same wavelength; however, they can be identified with respect to the Hi-C location of the EBDs. In addition, EBDs are seen in other chromospheric/coronal channels of SDO/AIA, which suggests a temperature between 0.5 and 1.5 MK. Based on their frequency in the Hi-C time series, we define four different categories of EBDs: single peak, double peak, long duration, and bursty. Based on a potential field extrapolation from an SDO/HMI magnetogram, the EBDs appear at the footpoints of large-scale, trans-equatorial coronal loops. The Hi-C observations provide the first evidence of small-scale EUV heating events at the base of these coronal loops, which have a free magnetic energy of the order of 10{sup 26} erg.« less

The research-design interaction: lessons learned from an evidence-based design studio.

PubMed

Haq, Saif; Pati, Debajyoti

2010-01-01

As evidence-based design (EBD) emerges as a model of design practice, considerable attention has been given to its research component. However, this overshadows another essential component of EBD-the change agent, namely the designer. EBD introduced a new skill set to the practitioner: the ability to interact with scientific evidence. Industry sources suggest adoption of the EBD approach across a large number of design firms. How comfortable are these designers in integrating research with design decision making? Optimizing the interaction between the primary change agent (the designer) and the evidence is crucial to producing the desired outcomes. Preliminary to examining this question, an architectural design studio was used as a surrogate environment to examine how designers interact with evidence. Twelve students enrolled in a healthcare EBD studio during the spring of 2009. A three-phase didactic structure was adopted: knowing a hospital, knowing the evidence, and designing with knowledge and evidence. Products of the studio and questionnaire responses from the students were used as the data for analysis. The data suggest that optimization of the research-design relationship warrants consideration in four domains: (1) a knowledge structure that is easy to comprehend; (2) phase-complemented representation of evidence; (3) access to context and precedence information; and (4) a designer-friendly vocabulary.

Themes and Dimensions of Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Mustian, April L.; Cuenca-Sanchez, Yojanna

2012-01-01

Students with emotional and behavioral disorders (EBD) are one of the most underserved populations in today's schools (Kauffman, Mock, & Simpson, 2011). Many of these students also have additional disabilities in conjunction with an EBD identification, such as Learning Disabilities (LD), Attention Deficit Disorder (ADD), Attention Deficit…

Sources of Occupational Stress for Teachers of Students with Emotional and Behavioral Disorders.

ERIC Educational Resources Information Center

Nelson, J. Ron; Maculan, Amelia; Roberts, Maura L.; Ohlund, Barbara J.

2001-01-01

Occupational stress ratings from 415 teachers of students with emotional/behavioral disorders (EBD) was modeled by regression, using teacher demographic characteristics, working conditions, and the ability to work with children with EBD as factors. All working condition variables, professional experience, and ability to work with externalizing…

Culturally Responsive Writing Instruction for Secondary Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Chiu, Calli Lewis; Carrero, Kelly M.; Lusk, Mandy E.

2017-01-01

Research suggests that teachers often do not adequately prepare students with emotional and behavioral disorders (EBD) to utilize organizational structures and basic writing skills that are necessary to produce cohesive essays. Among the challenges of effectively teaching writing to secondary students with EBD is how to deliver culturally…

Teachers of Students with Emotional and Behavioral Disorders' Perceptions of the Importance of Selected Professional Standards of Practice

ERIC Educational Resources Information Center

Lusk, Mandy E.; Bullock, Lyndal M.

2013-01-01

Utilizing the Council for Exceptional Children's (CEC) standards delineated for preparation programs in teaching students with emotional and behavioral disorders (EBD), the present study sought to determine how graduates of one teacher preparation program perceived the importance of the standards in their work with students with EBD. Results…

An Initial Psychometric Evaluation of the CBCL 6-18 in a Sample of Youth with Autism Spectrum Disorders

ERIC Educational Resources Information Center

Pandolfi, Vincent; Magyar, Caroline I.; Dill, Charles A.

2012-01-01

Individuals with an autism spectrum disorder (ASD) often present with co-occurring emotional and behavioral disorders (EBD). The Child Behavior Checklist 6-18 (CBCL; Achenbach & Rescorla, 2001) is an EBD measure that contains several norm-referenced scales derived through factor analysis of data from the general pediatric population. The…

How We Might Make Special Education for Students with Emotional or Behavioral Disorders Less Stigmatizing

ERIC Educational Resources Information Center

Kauffman, James M.; Badar, Jeanmarie

2013-01-01

The authors note that identification as having emotional or behavioral disorders (EBD) is generally acknowledged to be stigmatizing. The stigma associated with identification as needing special education for EBD (or any other disability) could be reduced by talking in readily understood language about differences, accepting the reality of…

The Lived Experiences of Teachers of Students with Emotional Behavior Disorder

ERIC Educational Resources Information Center

Bell, Sheneka L.

2012-01-01

The purpose of this phenomenological study was to gain an understanding of teacher attrition among the emotional and behavior disorder (EBD) student population within a self-contained environment through the lived experiences of former EBD teachers. Attrition among special education teachers has been a perennial issue. Special education teacher…

Learned Helplessness and Students with Emotional or Behavioral Disorders: Deprivation in the Classroom

ERIC Educational Resources Information Center

Sutherland, Kevin S.; Singh, Nirbhay N.

2004-01-01

Students with emotional or behavioral disorders (E/BD) are characterized by academic deficits and classroom behavioral problems. The relationship between problem behavior and academic difficulties is complex, and some researchers have hypothesized that the classroom behavior problems of students with E/BD are responses to aversive stimuli, namely…

Constant Time Delay: One Way to Provide Positive Behavioral Support for Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Stevens, Kay B.; Lingo, Amy S.

2005-01-01

Teachers of students with emotional and behavioral disorders (EBD) understand conceptually, emotionally, and legally the importance of using research-based procedures as well as positive behavioral supports. One way to provide positive behavioral support for students with EBD is constant time delay (CTD). CTD is an instructional delivery procedure…

Fabrication of electron beam deposited tip for atomic-scale atomic force microscopy in liquid.

PubMed

Miyazawa, K; Izumi, H; Watanabe-Nakayama, T; Asakawa, H; Fukuma, T

2015-03-13

Recently, possibilities of improving operation speed and force sensitivity in atomic-scale atomic force microscopy (AFM) in liquid using a small cantilever with an electron beam deposited (EBD) tip have been intensively explored. However, the structure and properties of an EBD tip suitable for such an application have not been well-understood and hence its fabrication process has not been established. In this study, we perform atomic-scale AFM measurements with a small cantilever and clarify two major problems: contaminations from a cantilever and tip surface, and insufficient mechanical strength of an EBD tip having a high aspect ratio. To solve these problems, here we propose a fabrication process of an EBD tip, where we attach a 2 μm silica bead at the cantilever end and fabricate a 500-700 nm EBD tip on the bead. The bead height ensures sufficient cantilever-sample distance and enables to suppress long-range interaction between them even with a short EBD tip having high mechanical strength. After the tip fabrication, we coat the whole cantilever and tip surface with Si (30 nm) to prevent the generation of contamination. We perform atomic-scale AFM imaging and hydration force measurements at a mica-water interface using the fabricated tip and demonstrate its applicability to such an atomic-scale application. With a repeated use of the proposed process, we can reuse a small cantilever for atomic-scale measurements for several times. Therefore, the proposed method solves the two major problems and enables the practical use of a small cantilever in atomic-scale studies on various solid-liquid interfacial phenomena.

Language and reading comprehension in middle childhood predicts emotional and behaviour difficulties in adolescence for those with permanent childhood hearing loss.

PubMed

Stevenson, Jim; Pimperton, Hannah; Kreppner, Jana; Worsfold, Sarah; Terlektsi, Emmanouela; Mahon, Merle; Kennedy, Colin

2018-02-01

Permanent childhood hearing loss (PCHL) is associated with an elevated level of emotional and behaviour difficulties (EBD). In children and adolescents with PCHL, EBD has been found to be linked to language ability in children with PCHL. The present study was designed to test whether childhood language and/or reading comprehension abilities of children with PCHL predict subsequent EBD in adolescence. Language comprehension (LC) and reading comprehension (RC) were measured at ages 6-10 years (Time 1) and 13-20 years (Time 2) in participants with PCHL who preferred to communicate using spoken language (n = 57) and a hearing comparison group (n = 38). EBD was measured at both time points by parent and by teacher ratings on the Strengths and Difficulties Questionnaire. Within the PCHL group there were negative correlations between EBD scores and concurrent LC and RC scores at Time 1 and at Time 2. Cross-lagged latent variable models fitted to the longitudinal data indicated that the associations between LC, RC and teacher-rated EBD were more likely to arise from the impact of LC and RC on behaviour rather than the other way around. In those with PCHL, poor language and reading comprehension in middle childhood increased the risk of emotional and behaviour difficulties at school in the teenage years. The results suggest that effective language and literacy interventions for children with hearing loss may also bring benefits to their mental health. © 2017 The Authors. Journal of Child Psychology and Psychiatry published by John Wiley & Sons Ltd on behalf of Association for Child and Adolescent Mental Health.

The role of stents in the treatment of Crohn’s disease strictures

PubMed Central

Loras Alastruey, Carme; Andújar Murcia, Xavier; Esteve Comas, Maria

2016-01-01

Background and aims: Stenosis is one of the most frequent local complications in Crohn’s disease (CD). Surgery is not the ideal treatment because of the high rate of postoperative recurrence. Endoscopic balloon dilation (EBD) currently is the current treatment of choice for short strictures amenable to the procedure. However, it is not applicable or effective in all the cases, and it is not without related complications. Our goal was to summarize the published information regarding the use and the role of the stents in the treatment of CD stricture. A Medline search was performed on the terms “stricture,” “stenosis,” “stent” and “Crohn’s disease.” Results: a total of 19 publications met our search criteria for an overall number of 65 patients. Placing a self-expanding metal stent (SEMS) may be a safe and effective alternative to EBD and/or surgical intervention in the treatment of short stenosis in patients with CD. Indications are the same as those for EBD. In addition, SEMS may be useful in stenosis refractory to EBD and may be suitable in the treatment of longer or more complex strictures that cannot be treated by EBD. With the current information, it seems that the best treatment option is the placement of a fully covered stent for a mean time of 4 weeks. Regarding the use of biodegradable stents, the information is limited and showing poor results. Conclusions: the use of stents in the treatment of strictures in CD should be taken into account either as a first endoscopic therapy or in case of EBD failure. PMID:27014743

A Comparison of Teacher Perceptions and Research-Based Categories of Student Behavior Difficulties

ERIC Educational Resources Information Center

Conley, Laura; Marchant, Michelle; Caldarella, Paul

2014-01-01

Students with emotional and behavioral disorders (EBD) are less successful in school than their peers. In order for teachers and researchers to effectively partner to identify and support these students, they must focus on the same problem behaviors. This research identified six components of EBD commonly identified in research literature:…

Effects of a Summarizing Strategy on Written Summaries of Children with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Saddler, Bruce; Asaro-Saddler, Kristie; Moeyaert, Mariola; Ellis-Robinson, Tammy

2017-01-01

In this single-subject study, we examined the effects of a summarizing strategy on the written summaries of children with emotional and behavioral disorders (EBDs). Six students with EBDs in fifth and sixth grades learned a mnemonic-based strategy for summarizing taught through the self-regulated strategy development (SRSD) approach. Visual…

Critical Educational Program Components for Students with Emotional and Behavioral Disorders: Science, Policy, and Practice

ERIC Educational Resources Information Center

Simpson, Richard L.; Peterson, Reece L.; Smith, Carl R.

2011-01-01

In spite of recent education reform and reorganization efforts requiring the use of research-based methods, the fundamental elements of an effective program for children and youth with emotional and behavioral disorders (EBD) have not been succinctly identified. This article presents the essential features of programs for students with EBD.…

Teacher Implementation of Trial-Based Functional Analysis and Function-Based Interventions for Students with Challenging Behavior

ERIC Educational Resources Information Center

Flynn, Susan Dagenhart

2012-01-01

Children and youth with autism spectrum disorders (ASD) or emotional and behavioral disabilities (E/BD) often exhibit challenging behavior including aggression, self-injury, non-compliance, or property destruction (Kamps, Kravits, Rauch, Kamps, & Chung, 2000; National Autism Center, 2009). As a result, students with ASD or E/BD often miss out…

Building on the Data and Adding to the Discussion: The Experiences and Outcomes of Students with Emotional Disturbance

ERIC Educational Resources Information Center

Bradley, Renee; Doolittle, Jennifer; Bartolotta, Robert

2008-01-01

The purpose of this article is to add to the discussion regarding identification of students with emotional and behavioral disorders (EBD). In addition, the article discusses services that students with EBD receive and their outcomes. The article reviews data from several national longitudinal studies to present a comprehensive picture of issues…

The Relation between the Academic Achievement of Students with Emotional and Behavioral Disorders and Teacher Characteristics

ERIC Educational Resources Information Center

Gage, Nicholas A.; Adamson, Reesha; MacSuga-Gage, Ashley S.; Lewis, Timothy J.

2017-01-01

Teachers of students with emotional and/or behavioral disorders (EBD) are less experienced and more likely to have emergency certification than teachers of students with other disabilities. Yet, to date, research has not examined the relation between the academic achievement of students with EBD and characteristics associated with highly qualified…

Mathematics Instruction for Middle School Students with and At-Risk for Behavioral Disorders: A Survey Study

ERIC Educational Resources Information Center

Jones, Stacey Eagan Lefort

2012-01-01

This survey study was designed to investigate mathematics instruction for middle school students with and at-risk for emotional and behavioral disorders (EBD). It sought to identify who is teaching mathematics to students with and at-risk for EBD, investigate if mathematics and special education teachers are implementing recommended curricula and…

Developing Mathematical Understanding and Students with Emotional and Behavioural Disorders: A Review of the Literature

ERIC Educational Resources Information Center

Tan, Paulo

2016-01-01

Recent shifts in focus on academic interventions for students diagnosed with emotional and behavioural disorders (EBD) create a need to evaluate existing interventional research in content areas such as mathematics. Literature reviews in the area of mathematics interventions for students with EBD have mostly focused on the outcomes and the rigour…

A Meta-Analysis of the Academic Status of Students with Emotional/Behavioral Disturbance

ERIC Educational Resources Information Center

Reid, Robert; Gonzalez, Jorge E.; Nordness, Philip D.; Trout, Alexandra; Epstein, Michael H.

2004-01-01

Emotional/behavioral disturbance (EBD) is characterized by a range of behaviors that adversely affect a child's academic performance and cannot be explained by other sensory or health impairments. Although research has clearly demonstrated that children and youth with EBD tend to exhibit high rates of problem behavior, research on the…

Corrective Reading as a Supplementary Curriculum for Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

McDaniel, Sara C.; Houchins, David E.; Terry, Nicole P.

2013-01-01

Reading deficits among students with emotional and behavioral disorders (E/BD) are well documented. One approach to addressing these deficits has been providing students with intensive and explicit reading instruction. In this study, 31 students with E/BD and reading deficits in self-contained settings were provided with 8 weeks of…

Endoscopic balloon dilatation as an effective treatment for lower and upper benign gastrointestinal system anastomotic stenosis.

PubMed

Akarsu, Cevher; Unsal, Mustafa Gokhan; Dural, Ahmet Cem; Kones, Osman; Kocatas, Ali; Karabulut, Mehmet; Kankaya, Burak; Ates, Mustafa; Alis, Halil

2015-04-01

Endoscopic balloon dilatation (EBD) is currently accepted as an effective, safe, and first-line treatment of postoperative benign gastrointestinal anastomosis stenosis (BGAS); however, a limited number of publications on the subject exist in the literature. The aim of the study was to retrospectively evaluate the efficiency of endoscopic dilatation in patients with postoperative intestinal anastomotic stenoses at a single surgical center. Patients with postoperative BGAS treated by EBD at our institution from February 2008 to 2012 were included. The dilatations were all performed using through-the-scope balloons. The balloon was introduced into the stricture using a guidewire under radiologic guidance. Each dilatation session consisted of 2 to 3 two-minute multistep inflations of the balloon until adequate dilatation was achieved. Of the 48 patients included in the study, 44 patients (91.7%) fully recovered and 4 (8.3%) did not respond to treatment. The mean follow-up period was 24 months (range, 3 to 57 mo). Four patients who did not respond to the procedure were treated surgically. Two patients (4.1%) with intestinal perforation during EBD were treated conservatively with a stent. EBD has a low rate of complications and a high success rate, is well tolerated, and avoids further surgical procedures for BGAS. Therefore, EBD should be the first choice of treatment for postoperative anastomotic stenoses.

Difficulties Associated with the Coding and Categorization of Students with Emotional and Behavioural Disabilities in Alberta

ERIC Educational Resources Information Center

Wishart, Diane; Jahnukainen, Markku

2010-01-01

In Canada, there is a recent trend toward non-categorization of services of students with emotional and behavioural disabilities (EBD). Yet in Alberta, the coding of students with EBD provides opportunities to diagnose students' learning difficulties but is hindered in this process, in large part, by being tied into special needs funding. Current…

Effective Practices/Interventions for Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Bock, Stacey Jones; Borders, Christy

2012-01-01

Students with emotional and behavioral disorders (E/BD) present unique challenges to the families and educators supporting them. Even though families and educators report that behavioral issues can be identified by age 3 (Walker, Ramsey, & Gresham, 2004), the commonly used wait-and-see approach to intervening results in children with E/BD not…

Defining Administrative Support and Its Relationship to the Attrition of Teachers of Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Cancio, Edward J.; Albrecht, Susan Fread; Johns, Beverley H.

2013-01-01

Special education faces serious shortages of teachers, and the area of special education teaching with the greatest shortage is in the field emotional and behavioral disorders (EBD). This study was conducted to identify the perceptions of current teachers of students with EBD on the definition of and the extent and importance of administrative…

Meta-Analysis of Math Interventions for Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Templeton, Tran Nguyen; Neel, Richard S.; Blood, Erika

2008-01-01

Students with emotional and behavioral disorders (EBD) struggle in the area of academics as well as behavior, and these academic difficulties manifest a great deal in mathematics. The number of children with EBD served in general education settings is increasing, and mathematics curriculum is expanding to include additional content areas and more…

Emotional and Behavioural Difficulties among Middle School Students in Oman: An Examination of Prevalence Rate and Gender Differences

ERIC Educational Resources Information Center

Emam, Mahmoud Mohamed; Kazem, Ali Mahdi; Al-Zubaidy, Abdulqawi Salim

2016-01-01

Children with emotional and behavioural difficulties (EBDs) began to receive considerable attention in several countries in the Middle East and North Africa region including Oman. In the Omani context, there is lack of valid assessment instruments which can be used to obtain information on EBDs in schools. The current study used the Arabic…

Mechanism and influencing factors on critical pulse width of oil-immersed polymer insulators under short pulses

NASA Astrophysics Data System (ADS)

Zhao, Liang; Su, Jian Cang; Li, Rui; Zeng, Bo; Cheng, Jie; Zheng, Lei; Yu, Bin Xiong; Wu, Xiao Long; Zhang, Xi Bo; Pan, Ya Feng

2015-04-01

The critical pulse width (τc) is a pulse width at which the surface flashover threshold (Ef) is equal to the bulk breakdown threshold (EBD) for liquid-polymer composite insulation systems, which is discovered by Zhao et al. [Annual Report Conference on Electrical Insulation and Dielectric Phenomena (IEEE Dielectrics and Electrical Insulation Society, Shenzhen, China, 2013), Vol. 2, pp. 854-857]. In this paper, the mechanism of τc is interpreted in perspective of the threshold and the time delay (td) of surface flashover and bulk breakdown, respectively. It is found that two changes appear as the pulse width decreases which are responsible for the existence of τc: (1) EBD is lower than Ef; (2) td of bulk breakdown is shorter than td of surface flashover. In addition, factors which have influences on τc are investigated, such as the dielectric type, the insulation length, the dielectric thickness, the dielectrics configuration, the pulse number, and the liquid purity. These influences of factors are generalized as three types if τc is expected to increase: (1) factors causing EBD to decrease, such as increasing the pulse number or employing a dielectric of lower EBD; (2) factors causing Ef to increase, such as complicating the insulator's configuration or increasing the liquid purity; (3) factors causing EBD and Ef to increase together, but Ef increases faster than EBD, such as decreasing the dielectric thickness or the insulation length. With the data in references, all the three cases are verified experimentally. In the end, a general method based on τc for solid insulation design is presented and the significance of τc on solid insulation design and on solid demolition are discussed.

Is side-viewing endoscope assisted balloon dilatation better for corrosive gastric outlet obstruction?

PubMed

Katiyar, Prashant; Nijhawan, Sandeep; Saradava, Vimal; Nagaich, Neeraj; Gupta, Gaurav; Mathur, Amit; Nepalia, Subhash

2013-11-01

Endoscopic balloon dilatation (EBD) is an effective therapy for caustic-induced gastric outlet obstruction (GOO). Gaining access to the stricture site is the most important step. It is sometimes difficult to negotiate a balloon through the stricture with a front-viewing endoscope due to deformed anatomy of stomach. To overcome this technical difficulty, a side-viewing endoscope can be used. There is limited data regarding the use of side-viewing endoscopes in EBD. We here report on the short-term efficacy and safety of EBD in caustic-induced GOO. In technically difficult cases, a side-viewing endoscope was used for EBD and its efficacy and safety were assessed. The study included 25 patients with caustic-induced GOO. Patients underwent EBD using a through-the-scope balloon. Initial balloon dilatation was performed with a front-viewing endoscope. A side-viewing endoscope was used where negotiation across the stricture failed with a front-viewing endoscope. Dilatation was started at 8 mm diameter and was performed at 1-week intervals. The end point of dilatation was 15 mm diameter. In 18 patients successful balloon dilatation was possible with a front-viewing endoscope. A side-viewing endoscope was used in six patients as negotiation across the stricture was not possible with a front-viewing endoscope. In all six patients negotiation across the stricture followed by successful dilatation was successful with a side-viewing endoscope. Of the 25 patients included in this study, 24 (96%) achieved procedural success (18 with a front-viewing endoscope and 6 with a side-viewing endoscope) in 3-9 sessions. Our results show that EBD is a safe and effective option for caustic-induced GOO and in difficult cases a side-viewing endoscope can be used to achieve technical success.

A novel method for blood volume estimation using trivalent chromium in rabbit models.

PubMed

Baby, Prathap Moothamadathil; Kumar, Pramod; Kumar, Rajesh; Jacob, Sanu S; Rawat, Dinesh; Binu, V S; Karun, Kalesh M

2014-05-01

Blood volume measurement though important in management of critically ill-patients is not routinely estimated in clinical practice owing to labour intensive, intricate and time consuming nature of existing methods. The aim was to compare blood volume estimations using trivalent chromium [(51)Cr(III)] and standard Evans blue dye (EBD) method in New Zealand white rabbit models and establish correction-factor (CF). Blood volume estimation in 33 rabbits was carried out using EBD method and concentration determined using spectrophotometric assay followed by blood volume estimation using direct injection of (51)Cr(III). Twenty out of 33 rabbits were used to find CF by dividing blood volume estimation using EBD with blood volume estimation using (51)Cr(III). CF is validated in 13 rabbits by multiplying it with blood volume estimation values obtained using (51)Cr(III). The mean circulating blood volume of 33 rabbits using EBD was 142.02 ± 22.77 ml or 65.76 ± 9.31 ml/kg and using (51)Cr(III) was estimated to be 195.66 ± 47.30 ml or 89.81 ± 17.88 ml/kg. The CF was found to be 0.77. The mean blood volume of 13 rabbits measured using EBD was 139.54 ± 27.19 ml or 66.33 ± 8.26 ml/kg and using (51)Cr(III) with CF was 152.73 ± 46.25 ml or 71.87 ± 13.81 ml/kg (P = 0.11). The estimation of blood volume using (51)Cr(III) was comparable to standard EBD method using CF. With further research in this direction, we envisage human blood volume estimation using (51)Cr(III) to find its application in acute clinical settings.

Promise and Possibility in Special Education Services for Students with Emotional or Behavioral Disorders: Peacock Hill Revisited

ERIC Educational Resources Information Center

Gage, Nicholas A.; Adamson, Reesha; Mitchell, Barbara S.; Lierheimer, Kristin; O'Connor, Karen V.; Bailey, Natasha; Schultz, Tia; Schmidt, Carla; Jones, Stacey

2010-01-01

This article provides an historical look at how programs and practices for students with emotional or behavior disorders (E/BD) have been evaluated since 1964, leading to a codified, although not universally recognized, set of recommendations for evaluating best practices for students with E/BD set out by The Peacock Hill Working Group (1991). The…

Behavioral Disorders in the School: Participant Roles and Sub-Roles in Three Types of School Violence

ERIC Educational Resources Information Center

Gumpel, Thomas P.

2008-01-01

This study presents an attempt to widen the study of emotional and behavioral disorders (EBD) to include children not formally identified by the school as having EBD through examining the case of extreme school aggressors and their victims. The research describes the validation of the School Violence Inventory (SVI) and its use to map participant…

A Literature Review of Research Quality and Effective Practices in Alternative Education Settings

ERIC Educational Resources Information Center

Flower, Andrea; McDaniel, Sara C.; Jolivette, Kristine

2011-01-01

Effective behavioral practices for students with emotional/behavioral disorders (E/BD) are critical. Students with E/BD are often served in alternative education (AE) settings due to behavior that cannot be supported in a typical school setting or due to court adjudication based on delinquent activity. Like other settings for students with E/BD,…

Special Needs Characteristics of Children with Emotional and Behavioral Disorders that Affect Inclusion in Regular Education

ERIC Educational Resources Information Center

Stoutjesdijk, Regina; Scholte, Evert M.; Swaab, Hanna

2012-01-01

The aim of this study is to determine the discriminating special needs characteristics of children with emotional and behavioral disorders (EBD) that predict restrictiveness of placement in special education. The focus is on dynamic factors instead of static factors. To this end, 235 children with EBD in special schools and 111 children with EBD…

Academic Instruction and Students with Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Hagaman, Jessica L.

2012-01-01

Students with emotional and behavioral disorders (EBD) are known to experience academic deficits across core subject areas such as reading and mathematics. Until recently, less attention had been paid to the academic deficits of students with EBD. This was due, in part, to a common belief that academic deficits could not be addressed until problem…

Developing a System of Care: Interagency Collaboration for Students with Emotional/Behavioral Disorders. From the Mini-Library Series on Emotional/Behavioral Disorders.

ERIC Educational Resources Information Center

Skiba, Russell; And Others

This monograph offers an introduction to providing an interagency "system of care" for meeting the needs of children and youth with emotional/behavioral disorders (E/BD). This approach focuses on meeting the individual needs of children with E/BD in their home communities and supporting family members as allies in the treatment process. Strategies…

Toward Improved Accuracy: A Response to Kauffman and Badar

ERIC Educational Resources Information Center

Kamphaus, Randy; DiStefano, Christine

2013-01-01

The number of children estimated to suffer mental health disorders, and therefore, creating the need for special education services for children with emotional and behavioral disorders (EBD), is between 5% and 25% of children under the age of 18 (Brauner & Stephens, 2006). Admittedly, not all children with EBD have been identified and served,…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sule, Nishant; Yifat, Yuval; Gray, Stephen K.

We examine the formation and concomitant rotation of electrodynamically bound dimers (EBD) of 150nm diameter Ag nanoparticles trapped in circularly polarized focused Gaussian beams. The rotation frequency of an EBD increases linearly with the incident beam power, reaching high mean values of ~ 4kHz for a relatively low incident power of 14mW. Using a coupled-dipole/effective polarizability model, we reveal that retardation of the scattered fields and electrodynamic interactions can lead to a “negative torque” causing rotation of the EBD in the direction opposite to that of the circular polarization. This intriguing opposite-handed rotation due to negative torque is clearly demonstratedmore » using electrodynamics-Langevin dynamics simulations by changing particle separations and thus varying the retardation effects. Finally, negative torque is also demonstrated in experiments from statistical analysis of the EBD trajectories. These results demonstrate novel rotational dynamics of nanoparticles in optical matter using circular polarization and open a new avenue to control orientational dynamics through coupling to interparticle separation.« less

Therapeutic Ultrasound Enhancement of Drug Delivery to Soft Tissues

NASA Astrophysics Data System (ADS)

Lewis, George; Wang, Peng; Lewis, George; Olbricht, William

2009-04-01

Effects of exposure to 1.58 MHz focused ultrasound on transport of Evans Blue Dye (EBD) in soft tissues are investigated when an external pressure gradient is applied to induce convective flow through the tissue. The magnitude of the external pressure gradient is chosen to simulate conditions in brain parenchyma during convection-enhanced drug delivery (CED) to the brain. EBD uptake and transport are measured in equine brain, avian muscle and agarose brain-mimicking phantoms. Results show that ultrasound enhances EBD uptake and transport, and the greatest enhancement occurs when the external pressure gradient is applied. The results suggest that exposure of the brain parenchyma to ultrasound could enhance penetration of material infused into the brain during CED therapy.

Black Films and Film-Makers.

ERIC Educational Resources Information Center

Patterson, Lindsay, Ed.

The development of black films and the attitudes of the film industry toward black films and black actors are some of the topics examined in this anthology of essays. Section 1, "Nigger to Supernigger," contains such articles as "The Death of Rastus: Negroes in American Films" by Thomas R. Cripps and "Folk Values in a New Medium" by Alain Locke…

Integrating Research, Policy, and Practice to Bring Science to the Classroom: New Leaders' Perspectives on the Field of Emotional and Behavioral Disorders

ERIC Educational Resources Information Center

Maggin, Daniel M.; Robertson, Rachel; Oliver, Regina M.; Hollo, Alex; Partin, Tara C. Moore

2010-01-01

In 1991, the Peacock Hill Working Group provided the field of emotional and behavioral disorders (EBD) a roadmap for improving the quality of services provided to students with EBD. The working group considered issues at every level of the educational system, from the classroom to federal policy. Although many strides have been made in the past 20…

Evidence-Based Design and Research-Informed Design: What's the Difference? Conceptual Definitions and Comparative Analysis.

PubMed

Peavey, Erin; Vander Wyst, Kiley B

2017-10-01

This article provides critical examination and comparison of the conceptual meaning and underlying assumptions of the concepts evidence-based design (EBD) and research-informed design (RID) in order to facilitate practical use and theoretical development. In recent years, EBD has experienced broad adoption, yet it has been simultaneously critiqued for rigidity and misapplication. Many practitioners are gravitating to the term RID to describe their method of integrating knowledge into the design process. However, the term RID lacks a clear definition and the blurring of terms has the potential to weaken advances made integrating research into practice. Concept analysis methods from Walker and Avant were used to define the concepts for comparison. Conceptual definitions, process descriptions, examples (i.e., model cases), and methods of evaluation are offered for EBD and RID. Although EBD and RID share similarities in meaning, the two terms are distinct. When comparing evidence based (EB) and research informed, EB is a broad base of information types (evidence) that are narrowly applied (based), while the latter references a narrow slice of information (research) that is broadly applied (informed) to create an end product of design. Much of the confusion between the use of the concepts EBD and RID arises out of differing perspectives between the way practitioners and academics understand the underlying terms. The authors hope this article serves to generate thoughtful dialogue, which is essential to the development of a discipline, and look forward to the contribution of the readership.

[COMPARISON OF THE RISKS IN EATING DISORDERS AND BODY IMAGE AMONG MAPUCHES AND NOT MAPUCHES STUDENTS].

PubMed

Rosas Muñoz, Marcelo; Delgado Floody, Pedro; Cea Leiva, Fredy; Alarcón Hormazábal, Manuel; Alvarez San Martín, Roberto; Quezada Gallego, Karen

2015-12-01

there is little evidence about the risks of eating behavior (EBD) and body image disorders (BID) in teen and young ethnic Mapuches population. the purpose of the study was to establish whether there are differences in the risk of EBD and BID in Mapuches and not Mapuches students and associate these variables with the nutritional status. the sample was composed of 130 adolescents between 14 and 21 years; 95 Mapuches and 35 not Mapuches. In both groups was measured; body mass index (BMI), risks of disorder in the feeding behavior and body image. there were no differences in risks of EBD and ICT to compare by Mapuches ethnic group and not Mapuches (p>0.05). In the comparison by gender women showed higher values (p>0.05) at risk of eating disorders and BID. Students with malnutrition by excess obtained higher scores in the conduct of risk of BID (p=0.000). The risk of BID presented positive association with risk behaviors of EBD (p=0.000 and r=0.536). the non-presence of significant differences in the risk of EBD and BID, according to ethnicity, is explained in function of the processes of social and cultural change, where modernization has led to a normalization of cultural patterns associated with eating behavior and body aesthetics between urban, rural and indigenous populations. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Evidence-based dentistry for planning restorative treatments: barriers and potential solutions.

PubMed

Afrashtehfar, K I; Eimar, H; Yassine, R; Abi-Nader, S; Tamimi, F

2017-11-01

Evidence-based dentistry (EBD) can help provide the best treatment option for every patient, however, its implementation in restorative dentistry is very limited. This study aimed at assessing the barriers preventing the implementation of EBD among dental undergraduate and graduate students in Montreal, and explore possible solutions to overcome these barriers. A cross-sectional survey was conducted by means of a paper format self-administrated questionnaire distributed among dental students. The survey assessed the barriers and potential solutions for implementation of an evidence-based practice. Sixty-one students completed the questionnaire. Forty-one percent of respondents found evidence-based literature to be the most reliable source of information for restorative treatment planning, however, only 16% used it. They considered that finding reliable information was difficult and they sometimes encountered conflicting information when consulting different sources. Dental students had positive attitudes towards the need for better access to evidence-based literature to assist learning and decision making in restorative treatment planning and to improve treatment outcomes. Even for dentists trained in EBD, online searching takes too much time, and even though it can provide information of better quality than personal intuition, it might not be enough to identify the best available evidence. Even though dental students are aware of the importance of EBD in restorative dentistry they rarely apply the concept, mainly due to time constraints. For this reason, implementation of EBD would probably require faster access to evidence-based knowledge. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Influence of film dimensions on film droplet formation.

PubMed

Holmgren, Helene; Ljungström, Evert

2012-02-01

Aerosol particles may be generated from rupturing liquid films through a droplet formation mechanism. The present work was undertaken with the aim to throw some light on the influence of film dimensions on droplet formation with possible consequences for exhaled breath aerosol formation. The film droplet formation process was mimicked by using a purpose-built device, where fluid films were spanned across holes of known diameters. As the films burst, droplets were formed and the number and size distributions of the resulting droplets were determined. No general relation could be found between hole diameter and the number of droplets generated per unit surface area of fluid film. Averaged over all film sizes, a higher surface tension yielded higher concentrations of droplets. Surface tension did not influence the resulting droplet diameter, but it was found that smaller films generated smaller droplets. This study shows that small fluid films generate droplets as efficiently as large films, and that droplets may well be generated from films with diameters below 1 mm. This has implications for the formation of film droplets from reopening of closed airways because human terminal bronchioles are of similar dimensions. Thus, the results provide support for the earlier proposed mechanism where reopening of closed airways is one origin of exhaled particles.

Bioimpedence to Assess Breast Density as a Risk Factor for Breast Cancer in Adult Women and Adolescent Girls.

PubMed

Maskarinec, Gertraud; Morimoto, Yukiko; Laguana, Michelle B; Novotny, Rachel; Leon Guerrero, Rachael T

2016-01-01

Although high mammographic density is one of the strongest predictors of breast cancer risk, X-ray based mammography cannot be performed before the recommended screening age, especially not in adolescents and young women. Therefore, new techniques for breast density measurement are of interest. In this pilot study in Guam and Hawaii, we evaluated a radiation-free, bioimpedance device called Electrical Breast DensitometerTM (EBD; senoSENSE Medical Systems, Inc., Ontario, Canada) for measuring breast density in 95 women aged 31-82 years and 41 girls aged 8-18 years. Percent density (PD) was estimated in the women's most recent mammogram using a computer-assisted method. Correlation coefficients and linear regression were applied for statistical analysis. In adult women, mean EBD and PD values of the left and right breasts were 230±52 and 226±50 Ω and 23.7±15.1 and 24.2±15.2%, respectively. The EBD measurements were inversely correlated with PD (rSpearman=-0.52, p<0.0001); the correlation was stronger in Caucasians (rSpearman=-0.70, p<0.0001) than Asians (rSpearman=-0.54, p<0.01) and Native Hawaiian/Chamorro/Pacific Islanders (rSpearman=-0.34, p=0.06). Using 4 categories of PD (<10, 10-25, 26-50, 51-75%), the respective mean EBD values were 256±32, 249±41, 202±46, and 178±43 Ω (p<0.0001). In girls, the mean EBD values in the left and right breast were 148±40 and 155±54 Ω; EBD values decreased from Tanner stages 1 to 4 (204±14, 154±79, 136±43, and 119±16 Ω for stages 1-4, respectively) but were higher at Tanner stage 5 (165±30 Ω). With further development, this bioimpedance method may allow for investigations of breast development among adolescent, as well as assessment of breast cancer risk early in life and in populations without access to mammography.

Film Program Notes from the Current Holdings of the Anthology Film Archives; Outlines of 41 Films.

ERIC Educational Resources Information Center

Anthology Film Archives, New York, NY.

This collection of film program notes includes mixed commentary on some of the films held in the Anthology Film Archives (a film and book library in New York City). Some of the films are described by synopsis of the episodes and others by translation into English of the foreign language subtitles. However, each film noted is identified by full…

Early endoscopic balloon dilation in caustic-induced gastric injury.

PubMed

Kochhar, Rakesh; Poornachandra, Kuchhangi Sureshchandra; Dutta, Usha; Agrawal, Amit; Singh, Kartar

2010-04-01

There are no reports on endoscopic balloon dilation (EBD) for caustic-induced gastric outlet obstruction (GOO) in the acute or subacute phase. To study the efficacy of early EBD in patients with caustic-induced gastric injury. Tertiary care center in India. Retrospective analysis of data. Out of 41 patients with caustic-induced GOO who reported to us in the subacute phase between January 2001 and December 2008, 31 were treated by EBD. All 31 had ingested an acid 14.39 +/- 4.65 days earlier. EBD was achieved by using wire-guided balloons under endoscopic guidance. The balloon was negotiated across the narrowed segment and inflated for 60 seconds using a pressure gun. Balloons of incremental diameter, up to a maximum of 3 sizes, were used in each sitting. Procedural success was defined as reaching the end point of dilation (15 mm) and absence of symptoms. All 31 patients (18 male, mean age 32.06 +/- 11.04 years) could be successfully dilated. All but 1 underwent successful dilations to achieve the end point of 15 mm, requiring a median of 9 (range 3-18) dilations over a period of 7 (range 1.5-16) weeks. Complications included self-limiting pain (n = 10), bleeding at the time of the procedure (n = 9), and perforation in 1 patient (3.2%) who required surgery. Thirty patients were followed up for a median of 21 (range 3-72) months with no recurrence. Early EBD by an expert endoscopist is a safe and effective treatment modality in the management of caustic-induced GOO. Copyright 2010 American Society for Gastrointestinal Endoscopy. Published by Mosby, Inc. All rights reserved.

From dental science to clinical practice: Knowledge translation and evidence-based dentistry principles.

PubMed

Afrashtehfar, Kelvin I; Assery, Mansour K

2017-07-01

It has been claimed that in order to decrease the gap between what we know and what we do, research findings must be translated from knowledge to action. Such practices better enable dentists to make evidence-based decisions instead of personal ideas and judgments. To this end, this literature review aims to revisit the concepts of knowledge translation and evidence-based dentistry (EBD) and depict their role and influence within dental education. It addresses some possible strategies to facilitate knowledge translation (KT), encourage dental students to use EBD principles, and to encourage dental educators to create an environment in which students become self-directed learners. It concludes with a call to develop up-to-date and efficient online platforms that could grant dentists better access to EBD sources in order to more efficiently translate research evidence into the clinic.

The National Film Registry: Acquiring Our Film Heritage.

ERIC Educational Resources Information Center

Ziegler, Roy A.

The National Film Registry, which is primarily a designated list of films to be preserved by the Library of Congress, is also a valuable tool for selecting "films that are culturally, historically, and aesthetically significant." Following a brief discussion of the history and selection process of the National Film Registry, Southeast…

Film Reviews.

ERIC Educational Resources Information Center

Lance, Larry M.; Atwater, Lynn

1987-01-01

Reviews four Human Sexuality films and videos. These are: "Personal Decisions" (Planned Parenthood Federation of America, 1985); "The Touch Film" (Sterling Production, 1986); "Rethinking Rape" (Film Distribution Center, 1985); "Not A Love Story" (National Film Board of Canada, 1981). (AEM)

Film and membrane-model thermodynamics of free thin liquid films.

PubMed

Radke, C J

2015-07-01

In spite of over 7 decades of effort, the thermodynamics of thin free liquid films (as in emulsions and foams) lacks clarity. Following a brief review of the meaning and measurement of thin-film forces (i.e., conjoining/disjoining pressures), we offer a consistent analysis of thin-film thermodynamics. By carefully defining film reversible work, two distinct thermodynamic formalisms emerge: a film model with two zero-volume membranes each of film tension γ(f) and a membrane model with a single zero-volume membrane of membrane tension 2γ(m). In both models, detailed thermodynamic analysis gives rise to thin-film Gibbs adsorption equations that allow calculation of film and membrane tensions from measurements of disjoining-pressure isotherms. A modified Young-Laplace equation arises in the film model to calculate film-thickness profiles from the film center to the surrounding bulk meniscus. No corresponding relation exists in the membrane model. Illustrative calculations of disjoining-pressure isotherms for water are presented using square-gradient theory. We report considerable deviations from Hamaker theory for films less than about 3 nm in thickness. Such thin films are considerably more attractive than in classical Hamaker theory. Available molecular simulations reinforce this finding. Copyright © 2014 Elsevier Inc. All rights reserved.

Residential radon and environmental burden of disease among Non-smokers.

PubMed

Noh, Juhwan; Sohn, Jungwoo; Cho, Jaelim; Kang, Dae Ryong; Joo, Sowon; Kim, Changsoo; Shin, Dong Chun

2016-01-01

Lung cancer was the second highest absolute cancer incidence globally and the first cause of cancer mortality in 2014. Indoor radon is the second leading risk factor of lung cancer after cigarette smoking among ever smokers and the first among non-smokers. Environmental burden of disease (EBD) attributable to residential radon among non-smokers is critical for identifying threats to population health and planning health policy. To identify and retrieve literatures describing environmental burden of lung cancer attributable to residential radon, we searched databases including Ovid-MEDLINE, -EMBASE from 1980 to 2016. Search terms included patient keywords using 'lung', 'neoplasm', exposure keywords using 'residential', 'radon', and outcomes keywords using 'years of life lost', 'years of life lost due to disability', 'burden'. Searching through literatures identified 261 documents; further 9 documents were identified using manual searching. Two researchers independently assessed 271 abstracts eligible for inclusion at the abstract level. Full text reviews were conducted for selected publications after the first assessment. Ten studies were included in the final evaluation. Global disability-adjusted life years (DALYs)(95 % uncertainty interval) for lung cancer were increased by 35.9 % from 23,850,000(18,835,000-29,845,000) in 1900 to 32,405,000(24,400,000-38,334,000) in 2000. DALYs attributable to residential radon were 2,114,000(273,000-4,660,000) DALYs in 2010. Lung cancer caused 34,732,900(33,042,600 ~ 36,328,100) DALYs in 2013. DALYs attributable to residential radon were 1,979,000(1,331,000-2,768,000) DALYs for in 2013. The number of attributable lung cancer cases was 70-900 and EBD for radon was 1,000-14,000 DALYs in Netherland. The years of life lost were 0.066 years among never-smokers and 0.198 years among ever-smoker population in Canada. In summary, estimated global EBD attributable to residential radon was 1,979,000 DALYs for both sexes in 2013

Single-layer nano-carbon film, diamond film, and diamond/nano-carbon composite film field emission performance comparison

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiaoping, E-mail: wxpchina64@aliyun.com, E-mail: wxpchina@sohu.com; Shanghai Key Laboratory of Modern Optical System, Shanghai 200093; Wang, Jinye

A series of single-layer nano-carbon (SNC) films, diamond films, and diamond/nano-carbon (D/NC) composite films have been prepared on the highly doped silicon substrate by using microwave plasma chemical vapor deposition techniques. The films were characterised by scanning electron microscopy, Raman spectroscopy, and field emission I-V measurements. The experimental results indicated that the field emission maximum current density of D/NC composite films is 11.8–17.8 times that of diamond films. And the field emission current density of D/NC composite films is 2.9–5 times that of SNC films at an electric field of 3.0 V/μm. At the same time, the D/NC composite film exhibitsmore » the advantage of improved reproducibility and long term stability (both of the nano-carbon film within the D/NC composite cathode and the SNC cathode were prepared under the same experimental conditions). And for the D/NC composite sample, a high current density of 10 mA/cm{sup 2} at an electric field of 3.0 V/μm was obtained. Diamond layer can effectively improve the field emission characteristics of nano-carbon film. The reason may be due to the diamond film acts as the electron acceleration layer.« less

Exciton diffusion coefficient measurement in ZnO nanowires under electron beam irradiation.

PubMed

Donatini, Fabrice; Pernot, Julien

2018-03-09

In semiconductor nanowires (NWs) the exciton diffusion coefficient can be determined using a scanning electron microscope fitted with a cathodoluminescence system. High spatial and temporal resolution cathodoluminescence experiments are needed to measure independently the exciton diffusion length and lifetime in single NWs. However, both diffusion length and lifetime can be affected by the electron beam bombardment during observation and measurement. Thus, in this work the exciton lifetime in a ZnO NW is measured versus the electron beam dose (EBD) via a time-resolved cathodoluminescence experiment with a temporal resolution of 50 ps. The behavior of the measured exciton lifetime is consistent with our recent work on the EBD dependence of the exciton diffusion length in similar NWs investigated under comparable SEM conditions. Combining the two results, the exciton diffusion coefficient in ZnO is determined at room temperature and is found constant over the full span of EBD.

Film and History.

ERIC Educational Resources Information Center

Schaber, Robin L.

2002-01-01

Provides an annotated bibliography of Web sites that focus on using film to teach history. Includes Web sites in five areas: (1) film and education; (2) history of cinema; (3) film and history resources; (4) film and women; and (5) film organizations. (CMK)

Drop dynamics on a thin film: Thin film rupture

NASA Astrophysics Data System (ADS)

Carlson, Andreas; Kim, Pilnam; Stone, Howard A.

2011-11-01

The spreading of a water drop on an oil film that covers a solid substrate is a common event in many industrial processes. We study in experiments the dynamics of a water drop on a thin silicone oil film and quantify its interaction with the solid substrate that supports the film. The oil film becomes unstable and ruptures for solids that are hydrophilic. We determine the ``waiting time,'' the time it takes the water drop to drain the silicone film. This timescale is found to highly depend on how well water wets the solid, illustrating the interplay between intermolecular and hydrodynamic forces in the phenomenon. A phase diagram for the thin film stability is extracted based on waters equilibrium contact angle on the solid, which shows that we can either promote or inhibit de-wetting. As water comes in direct contact with the solid, it spreads and peels off the silicone film. We show the influence of viscosity, equilibrium contact angle and film height on the opening radius of the hole formed as the solid de-wets.

The Role of Endoscopic Biliary Drainage without Sphincterotomy in Gallstone Patients with Cholangitis and Suspected Common Bile Duct Stones Not Detected by Cholangiogram or Intraductal Ultrasonography

PubMed Central

Goong, Hyeon Jeong; Moon, Jong Ho; Lee, Yun Nah; Choi, Hyun Jong; Choi, Seo-Youn; Choi, Moon Han; Kim, Min Jin; Lee, Tae Hoon; Park, Sang-Heum; Lee, Hae Kyung

2017-01-01

Background/Aims Treatment for cholangitis without common bile duct (CBD) stones has not been established in patients with gallstones. We investigated the usefulness of endoscopic biliary drainage (EBD) without endoscopic sphincterotomy (EST) in patients diagnosed with gallstones and cholangitis without CBD stones by endoscopic retrograde cholangiopancreatography (ERCP) and intraductal ultrasonography (IDUS). Methods EBD using 5F plastic stents without EST was performed prospectively in patients with gallstones and cholangitis if CBD stones were not diagnosed by ERCP and IDUS. After ERCP, all patients underwent laparoscopic cholecystectomy. The primary outcomes were clinical and technical success. The secondary outcomes were recurrence rate of biliary events and procedure-related adverse events. Results Among 187 patients with gallstones and cholangitis, 27 patients without CBD stones according to ERCP and IDUS received EBD using 5F plastic stents without EST. The stents were maintained in all patients until laparoscopic cholecystectomy, and recurrence of cholangitis was not observed. After cholecystectomy, the stents were removed spontaneously in 12 patients and endoscopically in 15 patients. Recurrence of CBD stones was not detected during the follow-up period (median, 421 days). Conclusions EBD using 5F plastic stents without EST may be safe and effective for the management of cholangitis accompanied by gallstones in patients without CBD stones according to ERCP and IDUS. PMID:28104896

Contemporary Films' Mini Course on Film Study.

ERIC Educational Resources Information Center

Schillaci, Peter

This minicourse on film study can be a unit in English, in arts, or in the humanities. It can help to launch a film study course or complement an introduction to theater. Whatever form it takes, it helps to build a bridge to the student's media environment. Part one, the language of images, utilizes four films which demonstrate the basic elements…

American Film Genres: Approaches to a Critical Theory of Popular Film.

ERIC Educational Resources Information Center

Kaminsky, Stuart M.

This book is divided into twelve sections and contains photographs from many of the films discussed. The introduction defines film genre and describes the general theories behind this book; "The Individual Film" analyzes the film "Little Caesar" as it relates to the genre of gangster films; "Comparative Forms"…

Film: An Introduction.

ERIC Educational Resources Information Center

Fell, John L.

"Understanding Film," the opening section of this book, discusses perceptions of and responses to film and the way in which experiences with and knowledge of other media affect film viewing. The second section, "Film Elements," analyzes the basic elements of film: the use of space and time, the impact of editing, sound and color, and the effects…

Film Makers On Film Making.

ERIC Educational Resources Information Center

Geduld, Harry M., Ed.

This collection includes essays by and interviews with more than 30 film-makers, both classic and contemporary, on the subjects of their major interests and procedures in making films. The directors are: Louis Lumiere, Cecil Hepworth, Edwin S. Porter, Mack Sennett, David W. Griffith, Robert Flaherty, Charles Chaplin, Eric von Stroheim, Dziga…

Thinking Developmentally: The Next Evolution in Models of Health.

PubMed

Garner, Andrew S

2016-09-01

As the basic sciences that inform conceptions of human health advance, so must the models that are used to frame additional research, to teach the next generation of providers, and to inform health policy. This article briefly reviews the evolution from a biomedical model to a biopsychosocial (BPS) model and to an ecobiodevelopmental (EBD) model. Like the BPS model, the EBD model reaffirms the biological significance of psychosocial features within the patient's ecology, but it does so at the molecular and cellular levels. More importantly, the EBD model adds the dimension of time, forcing providers to "think developmentally" and to acknowledge the considerable biological and psychological consequences of previous experiences. For the health care system to move from a reactive "sick care" system to a proactive "well care" system, all providers must begin thinking developmentally by acknowledging the dynamic but cumulative dance between nature and nurture that drives development, behavior, and health, not only in childhood, but across the lifespan.

Methods for producing complex films, and films produced thereby

DOEpatents

Duty, Chad E.; Bennett, Charlee J. C.; Moon, Ji -Won; Phelps, Tommy J.; Blue, Craig A.; Dai, Quanqin; Hu, Michael Z.; Ivanov, Ilia N.; Jellison, Jr., Gerald E.; Love, Lonnie J.; Ott, Ronald D.; Parish, Chad M.; Walker, Steven

2015-11-24

A method for producing a film, the method comprising melting a layer of precursor particles on a substrate until at least a portion of the melted particles are planarized and merged to produce the film. The invention is also directed to a method for producing a photovoltaic film, the method comprising depositing particles having a photovoltaic or other property onto a substrate, and affixing the particles to the substrate, wherein the particles may or may not be subsequently melted. Also described herein are films produced by these methods, methods for producing a patterned film on a substrate, and methods for producing a multilayer structure.

Thin Films

NASA Astrophysics Data System (ADS)

Khorshidi, Zahra; Bahari, Ali; Gholipur, Reza

2014-11-01

Effect of annealing temperature on the characteristics of sol-gel-driven Ta ax La(1- a) x O y thin film spin-coated on Si substrate as a high- k gate dielectric was studied. Ta ax La(1- a) x O y thin films with different amounts of a were prepared (as-prepared samples). X-ray diffraction measurements of the as-prepared samples indicated that Ta0.3 x La0.7 x Oy film had an amorphous structure. Therefore, Ta0.3 x La0.7 x O y film was chosen to continue the present studies. The morphology of Ta0.3 x La0.7 x O y films was studied using scanning electron microscopy and atomic force microscopy techniques. The obtained results showed that the size of grain boundaries on Ta0.3 x La0.7 x O y film surfaces was increased with increasing annealing temperature. Electrical and optical characterizations of the as-prepared and annealed films were investigated as a function of annealing temperature using capacitance-voltage ( C- V) and current density-voltage ( J- V) measurements and the Tauc method. The obtained results demonstrated that Ta0.3 x La0.7 x O y films had high dielectric constant (≈27), wide band gap (≈4.5 eV), and low leakage current density (≈10-6 A/cm2 at 1 V).

The National Film Board's Studio D: Feminists Making Films for Peace.

ERIC Educational Resources Information Center

Taylor, Anita

Studio D of the National Film Board of Canada, a women's film making unit established to make films by, for, and about women, has created a group of five films that effectively develop the argument that women can and must join the effort to bring peace to a nuclear world. The first of these peace films, "If You Love This Planet,"…

Films Kids Like. A Catalog of Short Films For Children.

ERIC Educational Resources Information Center

Rice, Susan, Ed.

Information on the Children's Film Theater and a list of short films are contained in this catalog. The first section reviews the purpose of the Children's Film Theater, its history and what has been learned as a result of its efforts. Details on the mechanics of showing films for children are also covered, including matters such as screening…

Filming eugenics: teaching the history of eugenics through film.

PubMed

Ooten, Melissa; Trembanis, Sarah

2007-01-01

In teaching eugenics to undergraduate students and general public audiences, film should he considered as a provocative and fruitful medium that can generate important discussions about the intersections among eugenics, gender, class, race, and sexuality. This paper considers the use of two films, A Bill of Divorcement and The Lynchburg Story, as pedagogical tools for the history of eugenics. The authors provide background information on the films and suggestions for using the films to foster an active engagement with the historical eugenics movement.

Nanocomposite films

DOEpatents

Mitlin, David; , Ophus, Colin; Evoy, Stephane; Radmilovic, Velimir; Mohammadi, Reza; Westra, Ken; Nelson-Fitzpatrick, Nathaniel; Lee, Zonghoon

2010-07-20

A thin-film composition of nanocrystal molybdenum in an amorphous metallic matrix may be formed by co-sputtering Mo with aluminum or nickel. NEMS cantilevers may be formed from the film. The films exhibit high nanoindentation hardness and a reduction in roughness and intrinsic stress, while maintaining resistivity in the metallic range.

On Film

ERIC Educational Resources Information Center

Watts, Marty

2006-01-01

In this article, the author discusses the role of window films in enhancing indoor air quality in schools. Historically, window film has been used to reduce temperatures in buildings prone to overheating. Too much solar energy entering through windows makes occupants uncomfortable and air conditioning more costly. Film has been a simple solution…

UV actinometer film

NASA Technical Reports Server (NTRS)

Coulbert, C. D.; Gupta, A.; Pitts, J.

1980-01-01

Cumulative UV radiation can be measured by low-cost polymer film that is unaffacted by visible light. Useful for virtually any surface, film can help paint and plastics manufacturers determine how well their products stand up against UV radiation. Actinometer film uses photochemically sensitive compound that changes its chemical composition in response to solar radiation. Extent of chemical conversion depends on length exposure and can be measured by examining film sample with spectrophotometer. Film can be exposed from several seconds up to month.

Water-evaporation reduction by duplex films: application to the human tear film.

PubMed

Cerretani, Colin F; Ho, Nghia H; Radke, C J

2013-09-01

Water-evaporation reduction by duplex-oil films is especially important to understand the physiology of the human tear film. Secreted lipids, called meibum, form a duplex film that coats the aqueous tear film and purportedly reduces tear evaporation. Lipid-layer deficiency is correlated with the occurrence of dry-eye disease; however, in-vitro experiments fail to show water-evaporation reduction by tear-lipid duplex films. We review the available literature on water-evaporation reduction by duplex-oil films and outline the theoretical underpinnings of spreading and evaporation kinetics that govern behavior of these systems. A dissolution-diffusion model unifies the data reported in the literature and identifies dewetting of duplex films into lenses as a key challenge to obtaining significant evaporation reduction. We develop an improved apparatus for measuring evaporation reduction by duplex-oil films including simultaneous assessment of film coverage, stability, and temperature, all under controlled external mass transfer. New data reported in this study fit into the larger body of work conducted on water-evaporation reduction by duplex-oil films. Duplex-oil films of oxidized mineral oil/mucin (MOx/BSM), human meibum (HM), and bovine meibum (BM) reduce water evaporation by a dissolution-diffusion mechanism, as confirmed by agreement between measurement and theory. The water permeability of oxidized-mineral-oil duplex films agrees with those reported in the literature, after correction for the presence of mucin. We find that duplex-oil films of bovine and human meibum at physiologic temperature reduce water evaporation only 6-8% for a 100-nm film thickness pertinent to the human tear film. Comparison to in-vivo human tear-evaporation measurements is inconclusive because evaporation from a clean-water surface is not measured and because the mass-transfer resistance is not characterized. Copyright © 2013 Elsevier B.V. All rights reserved.

Thin teflon-like films for MEMS: Film properties and reliability studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, B.K.; LaVigne, G.; Sniegowski, J.J.

1998-07-01

This work presents film properties and initial reliability studies for thin Teflon-like films applied to a unique test vehicle, the Sandia-designed and fabricated microengine. Results on microengines coated with the film show a factor of three improvement in their lifetime and an order of magnitude reduction in the coefficient of friction when compared to uncoated samples. Coefficients Of Friction (COF) of 0.07 for the Teflon-like film and 1.0 for uncoated samples are extracted from models which match the measured behavior of working microengines. These films, deposited form a plasma source, exhibit the ability to penetrate into very narrow, deep channelsmore » common to many MEMS devices. For as-deposited film, both the refractive index at 1.4 and the contact angle with water at 108{degree} show the film to be very similar to bulk Teflon PTFE. Film stability as a function of temperature has been examined using Fourier Transformation Infrared (FTIR) spectroscopy. The film structure as observed by the fluorine-carbon (F-C) peak is stable up to 200 C, but starts decomposing above 250 C. Film composition has been examined using X-ray photoelectron spectroscopy (XPS) and is quite different for directly exposed surfaces compared with deep, narrow channels where the deposition process is diffusion limited.« less

Film in Development.

ERIC Educational Resources Information Center

Information Center on Instructional Technology Report, 1976

1976-01-01

The positive and negative aspects of using film as a medium for inducing change in developing nations are explored in this issue. Critics of the use of film for development cite (1) the culture specific nature of film content of foreign produced films; (2) the technical, economic, and logistical problems of in-country production; and (3) lack of…

Ag films deposited on Si and Ti: How the film-substrate interaction influences the nanoscale film morphology

NASA Astrophysics Data System (ADS)

Ruffino, F.; Torrisi, V.

2017-11-01

Submicron-thick Ag films were sputter deposited, at room temperature, on Si, covered by the native SiO2 layer, and on Ti, covered by the native TiO2 layer, under normal and oblique deposition angle. The aim of this work was to study the morphological differences in the grown Ag films on the two substrates when fixed all the other deposition parameters. In fact, the surface diffusivity of the Ag adatoms is different on the two substrates (higher on the SiO2 surface) due to the different Ag-SiO2 and Ag-TiO2 atomic interactions. So, the effect of the adatoms surface diffusivity, as determined by the adatoms-substrate interaction, on the final film morphology was analyzed. To this end, microscopic analyses were used to study the morphology of the grown Ag films. Even if the homologous temperature prescribes that the Ag film grows on both substrates in the zone I described by the structure zone model some significant differences are observed on the basis of the supporting substrate. In the normal incidence condition, on the SiO2/Si surface a dense close-packed Ag film exhibiting a smooth surface is obtained, while on the TiO2/Ti surface a more columnar film morphology is formed. In the oblique incidence condition the columnar morphology for the Ag film occurs both on SiO2/Si and TiO2/Ti but a higher porous columnar film is obtained on TiO2/Ti due to the lower Ag diffusivity. These results indicate that the adatoms diffusivity on the substrate as determined by the adatom-surface interaction (in addition to the substrate temperature) strongly determines the final film nanostructure.

Making the case for evidence-based design in healthcare: a descriptive case study of organizational decision making.

PubMed

Shoemaker, Lorie K; Kazley, Abby Swanson; White, Andrea

2010-01-01

The aim of this study was to describe the organizational decision-making process used in the selection of evidence-based design (EBD) concepts, the criteria used to make these decisions, and the extent to which leadership style may have influenced the decision-making process. Five research questions were formulated to frame the direction of this study, including: (1) How did healthcare leaders learn of innovations in design? (2) How did healthcare leaders make decisions in the selection of healthcare design concepts? (3) What criteria did healthcare leaders use in the decision-making process? (4) How did healthcare leaders consider input from the staff in design decisions? and (5) To what extent did the leadership style of administrators affect the outcomes of the decision-making process? Current issues affecting healthcare in the community led the principal investigator's organization to undertake an ambitious facilities expansion project. As part of its planning process, the organization learned of EBD principles that seemingly had a positive impact on patient care and safety and staff working conditions. Although promising, a paucity of empirical research addressed the cost/benefit of incorporating many EBD concepts into one hospital setting, and there was no research that articulated the organizational decision-making process used by healthcare administrators when considering the use of EBD in expansion projects. A mixed-method, descriptive, qualitative, single-case study and quantitative design were used to address the five research questions. The Systems Research Organizing Model provided the theoretical framework. A variety of data collection methods was used, including interviews of key respondents, the review of documentary evidence, and the Multifactor Leadership Questionnaire. A participatory process was used throughout the design decision phases, involving staff at all levels of the organization. The Internet and architects facilitated learning about

The New Film Technologies: Computerized Video-Assisted Film Production.

ERIC Educational Resources Information Center

Mott, Donald R.

Over the past few years, video technology has been used to assist film directors after they have shot a scene, to control costs, and to create special effects, especially computer assisted graphics. At present, a computer based editing system called "Film 5" combines computer technology and video tape with film to save as much as 50% of…

Contributions of Film Introductions and Film Summaries to Learning from Instructional Films.

ERIC Educational Resources Information Center

Lathrop, C. W., Jr.; Norford, C. A.

An exploratory study of the contribution to learning of typical introductory and summarizing sequences in instructional films underlined the need for further experimental work to determine what kinds of introductory and concluding sequences are most useful in promoting learning from films. The first part of the study was concerned with film…

Exploring the Film.

ERIC Educational Resources Information Center

Kuhns, William; Stanley, Robert

The purpose of film study is defined here in the words of D. W. Griffiths: "My goal is above all to make you see." This book is intended to be used as a text in a film study course. It traces the development of films from a scientific curiosity through silent films to modern wide screen productions. A comic strip is used to demonstrate the effect…

Electrochromic nanocomposite films

DOEpatents

Milliron, Delia; Llordes, Anna; Buonsanti, Raffaella; Garcia, Guillermo

2018-04-10

The present invention provides an electrochromic nanocomposite film. In an exemplary embodiment, the electrochromic nanocomposite film, includes (1) a solid matrix of oxide based material and (2) transparent conducting oxide (TCO) nanostructures embedded in the matrix. In a further embodiment, the electrochromic nanocomposite film farther includes a substrate upon which the matrix is deposited. The present invention also provides a method of preparing an electrochromic nanocomposite film.

The American Film Heritage; Impressions from the American Film Institute Archives.

ERIC Educational Resources Information Center

Shales, Tom; And Others

The American Film Institute has an archive which presently contains more than 9,000 films, many of them rare. The articles in this volume are based on some of the films in the collection. Among the topics of these essays are: pioneers like D. W. Griffith and Thomas H. Ince, treatment of blacks and Indians in films, development of the techniques…

International Film Guide 1972.

ERIC Educational Resources Information Center

Cowie, Peter, Ed.

Brief descriptions of film production activity in 44 countries and reviews of important films from these countries are presented, along with lists of films recently in production. A paragraph-long description of film festivals slated for 1972 is given. Sound track music available on records, 16mm films available in the United Kingdom and the…

Science Fiction on Film.

ERIC Educational Resources Information Center

Burmester, David

1985-01-01

Reviews science fiction films used in a science fiction class. Discusses feature films, short science fiction films, short story adaptations, original science fiction pieces and factual science films that enrich literature. (EL)

The evidence-based dentistry initiative at Baylor College of Dentistry.

PubMed

Jones, Daniel L; Hinton, Robert J; Dechow, Paul C; Abdellatif, Hoda; McCann, Ann L; Schneiderman, Emet D; D'Souza, Rena

2011-02-01

This report describes the impact of an R25 Oral Health Research Education Grant awarded to the Texas A&M Health Science Center-Baylor College of Dentistry (BCD) to promote the application of basic and clinical research findings to clinical training and encourage students to pursue careers in oral health research. At Baylor, the R25 grant supports a multi-pronged initiative that employs clinical research as a vehicle for acquainting both students and faculty with the tools of evidence-based dentistry (EBD). New coursework and experiences in all 4 years of the curriculum plus a variety of faculty development offerings are being used to achieve this goal. Progress on these fronts is reflected in a nascent "EBD culture" characterized by increasing participation and buy-in by students and faculty. The production of a new generation of dental graduates equipped with the EBD skill set as well as a growing nucleus of faculty who can model the importance of evidence-based practice is of paramount importance for the future of dentistry.

Introducing evidence-based dentistry to dental students using histology.

PubMed

Lallier, Thomas E

2014-03-01

The expansion of evidence-based dentistry (EBD) is essential to the continued growth and development of the dental profession. Expanding EBD requires increased emphasis on critical thinking skills during dental education, as noted in the American Dental Education Association's Competencies for the New General Dentist. In order to achieve this goal, educational exercises must be introduced to increase the use of critical thinking skills early in the dental curriculum, with continued reinforcement as students progress through subsequent years. Described in this article is one approach to increasing student exposure to critical thinking during the early basic science curriculum-specifically, within the confines of a traditional histology course. A method of utilizing the medical and dental research literature to reinforce and enliven the concepts taught in histology is described, along with an approach for using peer-to-peer presentations to demonstrate the tools needed to critically evaluate research studies and their presentation in published articles. This approach, which could be applied to any basic science course, will result in a stronger foundation on which students can build their EBD and critical thinking skills.

Lights … action: Comparison of trauma films for use in the trauma film paradigm.

PubMed

Arnaudova, Inna; Hagenaars, Muriel A

2017-06-01

Affective films are often used in emotion research and negative films are frequently used as an analogue for trauma (trauma film paradigm). However, different films are used with possibly distinct consequences. We aimed to investigate specific effects of four negative films covering distinct themes (physical, sexual, traffic and food), and tested neutral and positive films with matching content. Self-reported emotional responses and heart rate during the films were examined (immediate responses) as well as intrusions of the films in the subsequent week (delayed responses). Within each theme, negative films were rated as more unpleasant than the positive and neutral counterparts. They also evoked more negative emotions and more intrusive memories. Across themes, the four negative films did not differ in terms of valence and arousal, but clearly differed on immediate (e.g., disgust, embarrassment, heart rate) and delayed (intrusions) effects. Thus, we urge researchers to carefully select negative films for their studies, as different films seem to evoke distinct emotional responses. In addition, using positive films within the same themes is recommended in order to control for effects of arousal. In general, the specific film material should be considered when comparing effects across studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

Use of a control film piece in radiochromic film dosimetry.

PubMed

Aldelaijan, Saad; Alzorkany, Faisal; Moftah, Belal; Buzurovic, Ivan; Seuntjens, Jan; Tomic, Nada; Devic, Slobodan

2016-01-01

Radiochromic films change their color upon irradiation due to polymerization of the sensitive component embedded within the sensitive layer. However, agents, other than monitored radiation, can lead to a change in the color of the sensitive layer (temperature, humidity, UV light) that can be considered as a background signal and can be removed from the actual measurement by using a control film piece. In this work, we investigate the impact of the use of control film pieces on both accuracy and uncertainty of dose measured using radiochromic film based reference dosimetry protocol. We irradiated "control" film pieces (EBT3 GafChromic(TM) film model) to known doses in a range of 0.05-1 Gy, and five film pieces of the same size to 2, 5, 10, 15 and 20 Gy, considered to be "unknown" doses. Depending on a dose range, two approaches to incorporating control film piece were investigated: signal and dose corrected method. For dose values greater than 10 Gy, the increase in accuracy of 3% led to uncertainty loss of 5% by using dose corrected approach. At lower doses and signals of the order of 5%, we observed an increase in accuracy of 10% with a loss of uncertainty lower than 1% by using the corrected signal approach. Incorporation of the signal registered by the control film piece into dose measurement analysis should be a judgment call of the user based on a tradeoff between deemed accuracy and acceptable uncertainty for a given dose measurement. Copyright © 2015 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Thick Film Interference.

ERIC Educational Resources Information Center

Trefil, James

1983-01-01

Discusses why interference effects cannot be seen with a thick film, starting with a review of the origin of interference patterns in thin films. Considers properties of materials in films, properties of the light source, and the nature of light. (JN)

Electrochemical Properties of Si Film Electrodes Containing TiNi Thin-Film Current Collectors

NASA Astrophysics Data System (ADS)

Im, Yeon-min; Noh, Jung-pil; Cho, Gyu-bong; Nam, Tea-hyun

2018-03-01

A 50.3Ti-49.7Ni thin film fabricated by DC sputtering was employed as a current collector of Si film electrode. The structural and electrochemical properties of Si/TiNi film electrode were compared with those of a Si/Cu film electrode. The TiNi film with cluster-like structures composed of B2 austenitic phase at room temperature displayed the high electrochemical stability for Li ions. The amorphous Si film deposited on the TiNi film also consisted of cluster-like structures on the surface. The Si film grown on the TiNi film current collector (Si/TiNi electrode) demonstrated a high columbic efficiency of 87% at the first cycle (363 μAh/cm2 of charge capacity and 314 μAh/cm2 of discharge capacity). The Si/TiNi electrode exhibited better electrochemical properties in terms of capacity, cycle performance, and structural stability compared to the Si electrode with a conventional Cu foil current collector.

Usefulness of transpapillary bile duct brushing cytology and forceps biopsy for improved diagnosis in patients with biliary strictures.

PubMed

Kitajima, Yasuhiro; Ohara, Hirotaka; Nakazawa, Takahiro; Ando, Tomoaki; Hayashi, Kazuki; Takada, Hiroki; Tanaka, Hajime; Ogawa, Kanto; Sano, Hitoshi; Togawa, Shozo; Naito, Itaru; Hirai, Masaaki; Ueno, Koichiro; Ban, Tessin; Miyabe, Katuyuki; Yamashita, Hiroaki; Yoshimura, Norihiro; Akita, Shinji; Gotoh, Kazuo; Joh, Takashi

2007-10-01

Transpapillary bile duct brushing cytology and/or forceps biopsy was performed in the presence of an indwelling guidewire in patients with biliary stricture, and the treatment time, overall diagnosis rate, diagnosis rate of each disease, complications, and influences on subsequent biliary drainage were investigated. After endoscopic retrograde cholangiography, brushing cytology was performed, followed by forceps biopsy. In patients with obstructive jaundice, endoscopic biliary drainage (EBD) was subsequently performed. To investigate the influences of bile duct brushing cytology and forceps biopsy on EBD, patients who underwent subsequent EBD by plastic stent were compared with patients who underwent EBD alone. The samples for cytology were collected successfully in all cases, and the sensitivity for malignancy/benignity, specificity, and accuracy were 71.6%, 100%, and 75.0%, respectively. The biopsy sampling was successful in 51 patients, and samples applicable to the evaluation were collected in all 51 patients. The sensitivity for malignancy/benignity, specificity, and accuracy were 65.2%, 100%, and 68.6%, respectively. Combination of the two procedures increased the sensitivity and accuracy to 73.5% and 76.6%, respectively. The time required for cytology and biopsy was 11.7 min, which is relatively short. Cytology and biopsy did not affect drainage. Regarding accidents, bile duct perforation occurred during biopsy in one patient (1.9%), but was rapidly improved by endoscopic biliary drainage. Transpapillary brushing cytology and forceps biopsy could be performed in a short time. The diagnosis rate was high, and the incidence of complication was low, having no influence on subsequent biliary drainage.

Evidence-Based and Value-Based Decision Making About Healthcare Design: An Economic Evaluation of the Safety and Quality Outcomes.

PubMed

Zadeh, Rana; Sadatsafavi, Hessam; Xue, Ryan

2015-01-01

This study describes a vision and framework that can facilitate the implementation of evidence-based design (EBD), scientific knowledge base into the process of the design, construction, and operation of healthcare facilities and clarify the related safety and quality outcomes for the stakeholders. The proposed framework pairs EBD with value-driven decision making and aims to improve communication among stakeholders by providing a common analytical language. Recent EBD research indicates that the design and operation of healthcare facilities contribute to an organization's operational success by improving safety, quality, and efficiency. However, because little information is available about the financial returns of evidence-based investments, such investments are readily eliminated during the capital-investment decision-making process. To model the proposed framework, we used engineering economy tools to evaluate the return on investments in six successful cases, identified by a literature review, in which facility design and operation interventions resulted in reductions in hospital-acquired infections, patient falls, staff injuries, and patient anxiety. In the evidence-based cases, calculated net present values, internal rates of return, and payback periods indicated that the long-term benefits of interventions substantially outweighed the intervention costs. This article explained a framework to develop a research-based and value-based communication language on specific interventions along the planning, design and construction, operation, and evaluation stages. Evidence-based and value-based design frameworks can be applied to communicate the life-cycle costs and savings of EBD interventions to stakeholders, thereby contributing to more informed decision makings and the optimization of healthcare infrastructures. © The Author(s) 2015.

Films--Too Good for Words. A Directory of Nonnarrated 16mm Films.

ERIC Educational Resources Information Center

Parlato, Salvatore J., Jr.

A nonnarrated film is one that communicates pictorially on the strength of its visual unity, continuity, and coherence without relying on narration or dialogue. This directory lists 1,000 such 16mm films, mostly curriculum-oriented educational films, in three main parts. The first part describes films under subject headings such as the arts, other…

Durable solar mirror films

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Neill, Mark B.; Henderson, Andrew J.; Hebrink, Timothy J.

The present disclosure generally relates to durable solar mirror films, methods of making durable solar mirror films, and constructions including durable solar mirror films. In one embodiment, the present disclosure relates to a solar mirror film comprising: a multilayer optical film layer including having a coefficient of hygroscopic expansion of less than about 30 ppm per percent relative humidity; and a reflective layer having a coefficient of hygroscopic expansion.

Durable solar mirror films

DOEpatents

O'Neill, Mark B.; Henderson, Andrew J.; Hebrink, Timothy J.; Katare, Rajesh K.; Jing, Naiyong; North, Diane; Peterson, Eric M.

2017-02-14

The present disclosure generally relates to durable solar mirror films, methods of making durable solar mirror films, and constructions including durable solar mirror films. In one embodiment, the present disclosure relates to a solar mirror film comprising: a multilayer optical film layer including having a coefficient of hygroscopic expansion of less than about 30 ppm per percent relative humidity; and a reflective layer having a coefficient of hygroscopic expansion.

Temperature-controlled transparent-film heater based on silver nanowire-PMMA composite film

NASA Astrophysics Data System (ADS)

He, Xin; Liu, A.'lei; Hu, Xuyang; Song, Mingxia; Duan, Feng; Lan, Qiuming; Xiao, Jundong; Liu, Junyan; Zhang, Mei; Chen, Yeqing; Zeng, Qingguang

2016-11-01

We fabricated a high-performance film heater based on a silver nanowire and polymethyl methacrylate (Ag NW-PMMA) composite film, which was synthesized with the assistance of mechanical lamination and an in situ transfer method. The films exhibit excellent conductivity, high figure of merit, and strong adhesion of percolation network to substrate. By controlling NW density, we prepared the films with a transmittance of 44.9-85.0% at 550 nm and a sheet resistance of 0.13-1.40 Ω sq-1. A stable temperature ranging from 130 °C-40 °C was generated at 3.0 V within 10-30 s, indicating that the resulting film heaters show a rapid thermal response, low driving voltage and stable temperature recoverability. Furthermore, we demonstrated the applications of the film heater in defrosting and a physical therapeutic instrument. A fast defrosting on the composite film with a transmittance of 88% was observed by applying a 9 V driving voltage for 20 s. Meanwhile, we developed a physical therapeutic instrument with two modes of thermotherapy and electronic-pulse massage by using the composite films as two electrodes, greatly decreasing the weight and power consumption compared to a traditional instrument. Therefore, Ag NW-PMMA film can be a promising candidate for diversified heating applications.

Buy, Borrow, or Steal? Film Access for Film Studies Students

ERIC Educational Resources Information Center

Rodgers, Wendy

2018-01-01

Libraries offer a mix of options to serve the film studies curriculum: streaming video, DVDs on Reserve, and streaming DVDs through online classrooms. Some professors screen films and lend DVDs to students. But how do students obtain the films required for their courses? How would they prefer to do so? These are among the questions explored using…

Chronicles of foam films.

PubMed

Gochev, G; Platikanov, D; Miller, R

2016-07-01

The history of the scientific research on foam films, traditionally known as soap films, dates back to as early as the late 17th century when Boyle and Hooke paid special attention to the colours of soap bubbles. Their inspiration was transferred to Newton, who began systematic study of the science of foam films. Over the next centuries, a number of scientists dealt with the open questions of the drainage, stability and thickness of foam films. The significant contributions of Plateau and Gibbs in the middle/late 19th century are particularly recognized. After the "colours" method of Newton, Reinold and Rücker as well as Johhonnot developed optical methods for measuring the thickness of the thinner "non-colour" films (first order black) that are still in use today. At the beginning of the 20th century, various aspects of the foam film science were elucidated by the works of Dewar and Perrin and later by Mysels. Undoubtedly, the introduction of the disjoining pressure by Derjaguin and the manifestation of the DLVO theory in describing the film stability are considered as milestones in the theoretical development of foam films. The study of foam films gained momentum with the introduction of the microscopic foam film methodology by Scheludko and Exerowa, which is widely used today. This historical perspective serves as a guide through the chronological development of knowledge on foam films achieved over several centuries. Copyright © 2015 Elsevier B.V. All rights reserved.

Water depth penetration film test

NASA Technical Reports Server (NTRS)

Lockwood, H. E.; Perry, L.; Sauer, G. E.; Lamar, N. T.

1974-01-01

As part of the National Aeronautics and Space Administration Earth Resources Program, a comparative and controlled evaluation of nine film-filter combinations was completed to establish the relative effectiveness in recording water subsurface detail if exposed from an aerial platform over a typical water body. The films tested, with one exception, were those which prior was suggested had potential. These included an experimental 2-layer positive color film, a 2-layer (minus blue layer) film, a normal 3-layer color film, a panchromatic black-and-white film, and a black-and-white infrared film. Selective filtration was used with all films.

Evaluation and mitigation of potential errors in radiochromic film dosimetry due to film curvature at scanning.

PubMed

Palmer, Antony L; Bradley, David A; Nisbet, Andrew

2015-03-08

This work considers a previously overlooked uncertainty present in film dosimetry which results from moderate curvature of films during the scanning process. Small film samples are particularly susceptible to film curling which may be undetected or deemed insignificant. In this study, we consider test cases with controlled induced curvature of film and with film raised horizontally above the scanner plate. We also evaluate the difference in scans of a film irradiated with a typical brachytherapy dose distribution with the film naturally curved and with the film held flat on the scanner. Typical naturally occurring curvature of film at scanning, giving rise to a maximum height 1 to 2 mm above the scan plane, may introduce dose errors of 1% to 4%, and considerably reduce gamma evaluation passing rates when comparing film-measured doses with treatment planning system-calculated dose distributions, a common application of film dosimetry in radiotherapy. The use of a triple-channel dosimetry algorithm appeared to mitigate the error due to film curvature compared to conventional single-channel film dosimetry. The change in pixel value and calibrated reported dose with film curling or height above the scanner plate may be due to variations in illumination characteristics, optical disturbances, or a Callier-type effect. There is a clear requirement for physically flat films at scanning to avoid the introduction of a substantial error source in film dosimetry. Particularly for small film samples, a compression glass plate above the film is recommended to ensure flat-film scanning. This effect has been overlooked to date in the literature.

Getting into Film.

ERIC Educational Resources Information Center

London, Mel

This book describes the various aspects of the film industry and the many jobs related to filmmaking, stressing that no "formula" exists for finding a successful career in the film industry. Chapters provide information on production, writing for film, cinematography, editing, music, sound, animation and graphics, acting and modeling, the "unsung…

The Sponsored Film.

ERIC Educational Resources Information Center

Klein, Walter J.

For public relations professionals and would-be sponsors of films, this book provides guidelines for understanding the film medium and its potential as a persuasive force in industry, government, organizations, and religious orders. For filmmakers, it brings together practical information needed to survive in the sponsored-film industry and to…

Film Reviews

ERIC Educational Resources Information Center

Dowling, John, Ed.

1976-01-01

Reviews five instructional films on: P-N junctions; crystal diodes; nuclear fusion research; Schlieren photography; and the energy crisis; including discussions of solar, nuclear, and fossil fuel energy. Also lists numerous other available films. (MLH)

Film Boxes.

ERIC Educational Resources Information Center

Osterer, Irv

2002-01-01

Presents an art lesson in which students created three-dimensional designs for 35mm film packages to improve graphic arts learning. Describes how the students examined and created film boxes using QuarkXPress software. (CMK)

Changes in the temperature-dependent specific volume of supported polystyrene films with film thickness.

PubMed

Huang, Xinru; Roth, Connie B

2016-06-21

Recent studies have measured or predicted thickness-dependent shifts in density or specific volume of polymer films as a possible means of understanding changes in the glass transition temperature Tg(h) with decreasing film thickness with some experimental works claiming unrealistically large (25%-30%) increases in film density with decreasing thickness. Here we use ellipsometry to measure the temperature-dependent index of refraction of polystyrene (PS) films supported on silicon and investigate the validity of the commonly used Lorentz-Lorenz equation for inferring changes in density or specific volume from very thin films. We find that the density (specific volume) of these supported PS films does not vary by more than ±0.4% of the bulk value for film thicknesses above 30 nm, and that the small variations we do observe are uncorrelated with any free volume explanation for the Tg(h) decrease exhibited by these films. We conclude that the derivation of the Lorentz-Lorenz equation becomes invalid for very thin films as the film thickness approaches ∼20 nm, and that reports of large density changes greater than ±1% of bulk for films thinner than this likely suffer from breakdown in the validity of this equation or in the difficulties associated with accurately measuring the index of refraction of such thin films. For larger film thicknesses, we do observed small variations in the effective specific volume of the films of 0.4 ± 0.2%, outside of our experimental error. These shifts occur simultaneously in both the liquid and glassy regimes uniformly together starting at film thicknesses less than ∼120 nm but appear to be uncorrelated with Tg(h) decreases; possible causes for these variations are discussed.

Combination film/splash fill for overcoming film fouling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phelps, P.M.; Minett, T.O.

1995-02-01

In summary, this large cooling tower user has found the Phelps film/splash Stack-Pack fill design to attain a substantial improvement in capability of their existing crossflow cooling towers, without increasing fan power or tower size. The lack of fouling in the film fill component of this fill design is due to the use of film fill with large (1 inch) spacing between sheets, coupled with effective water treatment as provided by Nalco. This combination of factors provides a proven method for significantly increasing crossflow or counterflow cooling tower capability while minimizing chances of serious fill fouling.

Ceramic Composite Thin Films

NASA Technical Reports Server (NTRS)

Dikin, Dmitriy A. (Inventor); Nguyen, SonBinh T. (Inventor); Ruoff, Rodney S. (Inventor); Stankovich, Sasha (Inventor)

2013-01-01

A ceramic composite thin film or layer includes individual graphene oxide and/or electrically conductive graphene sheets dispersed in a ceramic (e.g. silica) matrix. The thin film or layer can be electrically conductive film or layer depending the amount of graphene sheets present. The composite films or layers are transparent, chemically inert and compatible with both glass and hydrophilic SiOx/silicon substrates. The composite film or layer can be produced by making a suspension of graphene oxide sheet fragments, introducing a silica-precursor or silica to the suspension to form a sol, depositing the sol on a substrate as thin film or layer, at least partially reducing the graphene oxide sheets to conductive graphene sheets, and thermally consolidating the thin film or layer to form a silica matrix in which the graphene oxide and/or graphene sheets are dispersed.

Microfilm--Which Film Type, Which Application?

ERIC Educational Resources Information Center

Dodson, Suzanne Cates

1985-01-01

Report on characteristics of different kinds of microfilm available indicates proper film for specific needs. Silver halide and nonsilver films, diazo film, vesicular film, reaction of films to light, effect of heat and humidity on films, film susceptibility to scratching, and potential longevity of film types are covered. (35 references) (EJS)

[Application of biodegradable plastic film to reduce plastic film residual pollution in Chinese agriculture].

PubMed

Yan, Changrong; He, Wenqing; Xue, Yinghao; Liu, Enke; Liu, Qin

2016-06-25

Plastic film has become an important agriculture production material in recent years. Over the past three decades, the amount and application area of plastic film have increased steadily, and in 2014, which are 1.4 million tons and more than 180 million hm² respectively. It plays a key role for ensuring the supply of agricultural goods in China. Meanwhile, plastic film residual pollution becomes more and more serious, and in some regions, the amount of plastic film residues has reached over 250 kg/hm². In part of the Northwest region, soil structure of farmland has been destroyed by plastic film residues and then crop growth and farming operations were suppressed. It is recognized as a good choice to replace plastic film with biodegradable plastic film, an effective measure to solve the plastic film residue pollution. Now, it is in a critical stage of study and assessment of biodegradable plastic film in China and fortunately some biodegradable plastic films show effects in the production of potatoes, peanuts and tobacco. Overall, a series of challenges has still been faced by the biodegradable plastic film, mainly including improving the quality of biodegradable plastic products, such as tensile strength, flexibility, improving the controllability of rupture and degradation, enhancing the ability of increasing soil temperature and preserving soil moisture, and to satisfy the demand of crops production with mulching. In addition, it is essential to reduce the cost of the biodegradable film and promote the application of biodegradable film on large-scale. With the development of biodegradable plastic technology and agricultural production environment, the application of the biodegradable film will have a good future.

Meteor Film Recording with Digital Film Cameras with large CMOS Sensors

NASA Astrophysics Data System (ADS)

Slansky, P. C.

2016-12-01

In this article the author combines his professional know-how about cameras for film and television production with his amateur astronomy activities. Professional digital film cameras with high sensitivity are still quite rare in astronomy. One reason for this may be their costs of up to 20 000 and more (camera body only). In the interim, however,consumer photo cameras with film mode and very high sensitivity have come to the market for about 2 000 EUR. In addition, ultra-high sensitive professional film cameras, that are very interesting for meteor observation, have been introduced to the market. The particular benefits of digital film cameras with large CMOS sensors, including photo cameras with film recording function, for meteor recording are presented by three examples: a 2014 Camelopardalid, shot with a Canon EOS C 300, an exploding 2014 Aurigid, shot with a Sony alpha7S, and the 2016 Perseids, shot with a Canon ME20F-SH. All three cameras use large CMOS sensors; "large" meaning Super-35 mm, the classic 35 mm film format (24x13.5 mm, similar to APS-C size), or full format (36x24 mm), the classic 135 photo camera format. Comparisons are made to the widely used cameras with small CCD sensors, such as Mintron or Watec; "small" meaning 12" (6.4x4.8 mm) or less. Additionally, special photographic image processing of meteor film recordings is discussed.

Literature and Film.

ERIC Educational Resources Information Center

Richardson, Robert

The differences, similarities, and common goals of film and literature, as well as the ways in which each form and its associated criticism is able to illuminate the other, are discussed in this book. Individual chapters are "Literature and Film,""Literary Origins and Backgrounds of the Film,""Griffith and Eisenstein: The Uses of Literature in…

Film as Film; Understanding and Judging Movies.

ERIC Educational Resources Information Center

Perkins, V. F.

The criteria for judging movies which are presented here are based on the belief that film criticism becomes rational, if not "objective", when it displays and inspects the nature of its evidence and the bases of its arguments. The author dissents from the view of early film theorists that montage is the essence of cinema, and that cinema is to be…

[Films: China and Japan].

ERIC Educational Resources Information Center

Gumport, Roberta H.

The history of filmmaking in China and Japan and film usage in teaching are considered in this document. Pointing out how films describe historical context and culture, the document also describes various techniques of film making. Films in China were heavily influenced by western models and have tended to be tools of the power structure, as…

36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 3 2014-07-01 2014-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in the...

36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in the...

36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 3 2012-07-01 2012-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in the...

36 CFR 704.1 - Films selected for inclusion in the National Film Registry.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Films selected for inclusion in the National Film Registry. 704.1 Section 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in the...

Dewetting of Thin Polymer Films

NASA Astrophysics Data System (ADS)

Dixit, P. S.; Sorensen, J. L.; Kent, M.; Jeon, H. S.

2001-03-01

DEWETTING OF THIN POLYMER FILMS P. S. Dixit,(1) J. L. Sorensen,(2) M. Kent,(2) H. S. Jeon*(1) (1) Department of Petroleum and Chemical Engineering, New Mexico Institute of Mining and Technology, 801 Leroy Place, Socorro, NM 87801, jeon@nmt.edu (2) Department 1832, Sandia National Laboratories, Albuquerque, NM. Dewetting of thin polymer films is of technological importance for a variety of applications such as protective coatings, dielectric layers, and adhesives. Stable and smooth films are required for the above applications. Above the glass transition temperature (Tg) the instability of polymer thin films on a nonwettable substrate can be occurred. The dewetting mechanism and structure of polypropylene (Tg = -20 ^circC) and polystyrene (Tg = 100 ^circC) thin films is investigated as a function of film thickness (25 Åh < 250 Åand quenching temperature. Contact angle measurements are used in conjunction with optical microscope to check the surface homogeneity of the films. Uniform thin films are prepared by spin casting the polymer solutions onto silicon substrates with different contact angles. We found that the stable and unstable regions of the thin films as a function of the film thickness and quenching temperature, and then constructed a stability diagram for the dewetting of thin polymer films. We also found that the dewetting patterns of the thin films are affected substantially by the changes of film thickness and quenching temperature.

Evaluation and mitigation of potential errors in radiochromic film dosimetry due to film curvature at scanning

PubMed Central

Bradley, David A.; Nisbet, Andrew

2015-01-01

This work considers a previously overlooked uncertainty present in film dosimetry which results from moderate curvature of films during the scanning process. Small film samples are particularly susceptible to film curling which may be undetected or deemed insignificant. In this study, we consider test cases with controlled induced curvature of film and with film raised horizontally above the scanner plate. We also evaluate the difference in scans of a film irradiated with a typical brachytherapy dose distribution with the film naturally curved and with the film held flat on the scanner. Typical naturally occurring curvature of film at scanning, giving rise to a maximum height 1 to 2 mm above the scan plane, may introduce dose errors of 1% to 4%, and considerably reduce gamma evaluation passing rates when comparing film‐measured doses with treatment planning system‐calculated dose distributions, a common application of film dosimetry in radiotherapy. The use of a triple‐channel dosimetry algorithm appeared to mitigate the error due to film curvature compared to conventional single‐channel film dosimetry. The change in pixel value and calibrated reported dose with film curling or height above the scanner plate may be due to variations in illumination characteristics, optical disturbances, or a Callier‐type effect. There is a clear requirement for physically flat films at scanning to avoid the introduction of a substantial error source in film dosimetry. Particularly for small film samples, a compression glass plate above the film is recommended to ensure flat‐film scanning. This effect has been overlooked to date in the literature. PACS numbers: 87.55.Qr, 87.56.bg, 87.55.km PMID:26103181

7 CFR 2902.27 - Films.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Films. 2902.27 Section 2902.27 Agriculture... Films. (a) Definition. (1) Products that are used in packaging, wrappings, linings, and other similar applications. (2) Films for which preferred procurement applies are: (i) Semi-durable films. Films that are...

Development of Anti-Insect Microencapsulated Polypropylene Films Using a Large Scale Film Coating System.

PubMed

Song, Ah Young; Choi, Ha Young; Lee, Eun Song; Han, Jaejoon; Min, Sea C

2018-04-01

Films containing microencapsulated cinnamon oil (CO) were developed using a large-scale production system to protect against the Indian meal moth (Plodia interpunctella). CO at concentrations of 0%, 0.8%, or 1.7% (w/w ink mixture) was microencapsulated with polyvinyl alcohol. The microencapsulated CO emulsion was mixed with ink (47% or 59%, w/w) and thinner (20% or 25%, w/w) and coated on polypropylene (PP) films. The PP film was then laminated with a low-density polyethylene (LDPE) film on the coated side. The film with microencapsulated CO at 1.7% repelled P. interpunctella most effectively. Microencapsulation did not negatively affect insect repelling activity. The release rate of cinnamaldehyde, an active repellent, was lower when CO was microencapsulated than that in the absence of microencapsulation. Thermogravimetric analysis exhibited that microencapsulation prevented the volatilization of CO. The tensile strength, percentage elongation at break, elastic modulus, and water vapor permeability of the films indicated that microencapsulation did not affect the tensile and moisture barrier properties (P > 0.05). The results of this study suggest that effective films for the prevention of Indian meal moth invasion can be produced by the microencapsulation of CO using a large-scale film production system. Low-density polyethylene-laminated polypropylene films printed with ink incorporating microencapsulated cinnamon oil using a large-scale film production system effectively repelled Indian meal moth larvae. Without altering the tensile and moisture barrier properties of the film, microencapsulation resulted in the release of an active repellent for extended periods with a high thermal stability of cinnamon oil, enabling commercial film production at high temperatures. This anti-insect film system may have applications to other food-packaging films that use the same ink-printing platform. © 2018 Institute of Food Technologists®.

Australian Film Studies.

ERIC Educational Resources Information Center

Breen, Myles P.

Although Australia had a vigorous film industry in the silent film era, it was stifled in the 1930s when United States and British interests bought up the Australian distribution channels and closed down the indigenous industry. However, the industry and film study have undergone a renaissance since the advent of the Labor government in 1972,…

Analysis of Film.

ERIC Educational Resources Information Center

Stupp, Vicki O'Donnell

In order to understand the communicative interaction of film, it is necessary to carefully analyze the special qualities of film as a visual medium, to understand the elements of audience identification with what happens in the film, and to interpret the use of symbolism that enables an audience to derive meaning from it. Among the special…

Film Music. Factfile No. 8.

ERIC Educational Resources Information Center

Elsas, Diana, Ed.; And Others

Organizations listed here with descriptive information include film music clubs and music guilds and associations. These are followed by a representative list of schools offering film music and/or film sound courses. Sources are listed for soundtrack recordings, sound effects/production music, films on film music, and oral history programs. The…

Coating of plasma polymerized film

NASA Technical Reports Server (NTRS)

Morita, S.; Ishibashi, S.

1980-01-01

Plasma polymerized thin film coating and the use of other coatings is suggested for passivation film, thin film used for conducting light, and solid body lubrication film of dielectrics of ultra insulators for electrical conduction, electron accessories, etc. The special features of flow discharge development and the polymerized film growth mechanism are discussed.

Liquid-film electron stripper

DOEpatents

Gavin, Basil F.

1986-01-01

An improved liquid-film electron stripper particularly for high intensity heavy ion beams which produces constant regenerated, stable, free-standing liquid films having an adjustable thickness between 0.3 to 0.05 microns. The improved electron stripper is basically composed of at least one high speed, rotating disc with a very sharp, precision-like, ground edge on one said of the disc's periphery and with a highly polished, flat, radial surface adjacent the sharp edge. A fine stream of liquid, such as oil, impinges at a 90.degree. angle adjacent the disc's sharp outer edge. Film terminators, located at a selected distance from the disc perimeter are positioned approximately perpendicular to the film. The terminators support, shape, and stretch the film and are arranged to assist in the prevention of liquid droplet formation by directing the collected film to a reservoir below without breaking or interfering with the film. One embodiment utilizes two rotating discs and associated terminators, with the discs rotating so as to form films in opposite directions, and with the second disc being located down beam-line relative to the first disc.

About Films.

ERIC Educational Resources Information Center

Christman, Robert; Krockover, Gerald H.

1984-01-01

Lists and briefly describes 46 college-level films. Films are arranged in the following categories: volcanism and earthquakes; plate tectonics; energy, water, and environmental concerns; petroleum and coal; astronomy; space exploration, space shuttle; paleontology; geomorphology; and mineralogy, petrology, and economic geology. (BC)

Tribological properties of sputtered MoS sub 2 films in relation to film morphology

NASA Technical Reports Server (NTRS)

Spalvins, T.

1980-01-01

Thin sputter deposited MoS2 films in the 2000 to 6000 A thickness range have shown excellent lubricating properties, when sputtering parameters and substrate conditions are properly selected and precisely controlled. The lubricating properties of sputtered MoS2 films are strongly influenced by their crystalline-amorphous structure, morphology and composition. The coefficient of friction can range from 0.04 which is effective lubrication to 0.4 which reflects an absence of lubricating properties. Visual screening and slight wiping of the as-sputtered MoS2 film can identify the integrity of the film. An acceptable film displays a black-sooty surface appearance whereas an unacceptable film has a highly reflective, gray surface and the film is hard and brittle.

"Kuleshov on Film": A Spectator-Centered Film Theory.

ERIC Educational Resources Information Center

Curran, Trisha

This paper describes some of the theories of cinematography of Soviet film theorist and filmmaker Lev Kuleshov. It points out that for him, film was communication portraying people's activities emanating from the environment. It explains that he was especially interested in audience response, particularly that of the proletariat, and that he felt…

Radiochromic film dosimetry: considerations on precision and accuracy for EBT2 and EBT3 type films.

PubMed

Dreindl, Ralf; Georg, Dietmar; Stock, Markus

2014-05-01

Gafchromic® EBT2 film is a widely used dosimetric tool for quality assurance in radiation therapy. In 2012 EBT3 was presented as a replacement for EBT2 films. The symmetric structure of EBT3 films to reduce face-up/down dependency as well as the inclusion of a matte film surface to frustrate Newton Ring artifacts present the most prominent improvements of EBT3 films. The aim of this study was to investigate the characteristics of EBT3 films, to benchmark the films against the known EBT2-features and to evaluate the dosimetric behavior over a time period greater than 6 months. All films were irradiated to clinical photon beams (6 MV, 10 MV and 18 MV) on an Elekta Synergy Linac equipped with a Beam Modulator MLC in solid water phantom slabs. Film digitalization was done with a flatbed transparency scanner (Type Epson Expression 1680 Pro). MATLAB® was used for further statistical calculations and image processing. The investigations on post-irradiation darkening, film orientation, film uniformity and energy dependency resulted in negligible differences between EBT2 and EBT3 film. A minimal improvement in face-up/down dependence was found for EBT3. The matte film surface of EBT3 films turned out to be a practical feature as Newton rings could be eliminated completely. Considering long-term behavior (> 6 months) a shift of the calibration curve for EBT2 and EBT3 films due to changes in the dynamic response of the active component was observed. In conclusion, the new EBT3 film yields comparable results to its predecessor EBT2. The general advantages of radiochromic film dosimeters are completed by high film homogeneity, low energy dependence for the observed energy range and a minimized face-up/down dependence. EBT2 dosimetry-protocols can also be used for EBT3 films, but the inclusion of periodical recalibration-interval (e.g. once a quarter) is recommended for protocols of both film generations. Copyright © 2013. Published by Elsevier GmbH.

Physical-mechanical properties of agar/κ-carrageenan blend film and derived clay nanocomposite film.

PubMed

Rhim, Jong-Whan

2012-12-01

Binary blend films with different mixing ratio of agar and κ-carrageenan were prepared using a solution casting method with and without nanoclay and the effect of their composition on the mechanical, water vapor barrier, and water resistance properties was tested. The tensile strength (TS) of the κ-carrageenan film was greater than that of agar film. The water vapor permeability (WVP) of the agar film was lower than that of κ-carrageenan film, the swelling ratio (SR) and water solubility (WS) of κ-carrageenan film were higher than those of agar film. Each property of the binary blend films varied proportionately depending on the mixing ratio of each component. The XRD result indicated that the nanocomposite with agar/κ-carrageenan/clay (Cloisite(®) Na(+)) was intercalated. Consequently, the mechanical strength, water vapor barrier properties, and water contact angle (CA) were significantly (P < 0.05) improved through nanocomposite formation. © 2012 Institute of Food Technologists®

Feasibility demonstration for electroplating ultra-thin polyimide film. [fabricating film for space erectable structures

NASA Technical Reports Server (NTRS)

Schneier, R.; Braswell, T. V.; Vaughn, R. W.

1978-01-01

The effect of electrodeposition variables on film thickness was investigated using a dilute polyimide solution as a bath into which aluminum (as foil or as a vapor deposited coating) was immersed. The electrodeposited film was dried for 2 hours at 93 C (primarily to remove solvent) and cured for 18 hours at 186 C. Infrared studies indicate that imide formation (curing) occurs at 149 C under vacuum. From a conceptual viewpoint, satisfactory film metallized on one side can be obtained by this method. The cured ultra thin polyimide film exhibits properties equivalent to those of commercial film, and the surface appearance of the strippable polyimide film compares favorably with that of a sample of commercial film of thicker gauge. The feasibility of manufacturing approximately one million sq m of ultra thin film capable of being joined to fabricate an 800 m by 9 800 m square from starting material 0.5 to 1 m wide for space erectable structures was demonstrated.

Film Review. Films for Use in Professional Courses.

ERIC Educational Resources Information Center

Graham, Mike, Ed.

This book contains a detailed review of over ninety films in the professional preparation of teachers. It is one of eight publications which have been produced by the Science Teacher Education Project. Some of the films have become integral parts of the learning experiences which college and university people have prepared and others are…

Documentary Elements in Early Films.

ERIC Educational Resources Information Center

Sanderson, Richard A.

Focusing on documentary elements, this study examines the film content and film techniques of 681 motion pictures produced in the United States prior to 1904. Analysis of films by type, subject matter, and trends in subject matter shows that one-third of the early films are documentary in type and three-fourths of the films use subject matter of a…

Electronic Devices Based on Oxide Thin Films Fabricated by Fiber-to-Film Process.

PubMed

Meng, You; Liu, Ao; Guo, Zidong; Liu, Guoxia; Shin, Byoungchul; Noh, Yong-Young; Fortunato, Elvira; Martins, Rodrigo; Shan, Fukai

2018-05-30

Technical development for thin-film fabrication is essential for emerging metal-oxide (MO) electronics. Although impressive progress has been achieved in fabricating MO thin films, the challenges still remain. Here, we report a versatile and general thermal-induced nanomelting technique for fabricating MO thin films from the fiber networks, briefly called fiber-to-film (FTF) process. The high quality of the FTF-processed MO thin films was confirmed by various investigations. The FTF process is generally applicable to numerous technologically relevant MO thin films, including semiconducting thin films (e.g., In 2 O 3 , InZnO, and InZrZnO), conducting thin films (e.g., InSnO), and insulating thin films (e.g., AlO x ). By optimizing the fabrication process, In 2 O 3 /AlO x thin-film transistors (TFTs) were successfully integrated by fully FTF processes. High-performance TFT was achieved with an average mobility of ∼25 cm 2 /(Vs), an on/off current ratio of ∼10 7 , a threshold voltage of ∼1 V, and a device yield of 100%. As a proof of concept, one-transistor-driven pixel circuit was constructed, which exhibited high controllability over the light-emitting diodes. Logic gates based on fully FTF-processed In 2 O 3 /AlO x TFTs were further realized, which exhibited good dynamic logic responses and voltage amplification by a factor of ∼4. The FTF technique presented here offers great potential in large-area and low-cost manufacturing for flexible oxide electronics.

Fabrication of nitrogen-containing diamond-like carbon film by filtered arc deposition as conductive hard-coating film

NASA Astrophysics Data System (ADS)

Iijima, Yushi; Harigai, Toru; Isono, Ryo; Imai, Takahiro; Suda, Yoshiyuki; Takikawa, Hirofumi; Kamiya, Masao; Taki, Makoto; Hasegawa, Yushi; Tsuji, Nobuhiro; Kaneko, Satoru; Kunitsugu, Shinsuke; Habuchi, Hitoe; Kiyohara, Shuji; Ito, Mikio; Yick, Sam; Bendavid, Avi; Martin, Phil

2018-01-01

Diamond-like carbon (DLC) films, which are amorphous carbon films, have been used as hard-coating films for protecting the surface of mechanical parts. Nitrogen-containing DLC (N-DLC) films are expected as conductive hard-coating materials. N-DLC films are expected in applications such as protective films for contact pins, which are used in the electrical check process of integrated circuit chips. In this study, N-DLC films are prepared using the T-shaped filtered arc deposition (T-FAD) method, and film properties are investigated. Film hardness and film density decreased when the N content increased in the films because the number of graphite structures in the DLC film increased as the N content increased. These trends are similar to the results of a previous study. The electrical resistivity of N-DLC films changed from 0.26 to 8.8 Ω cm with a change in the nanoindentation hardness from 17 to 27 GPa. The N-DLC films fabricated by the T-FAD method showed high mechanical hardness and low electrical resistivity.

Ferroelectric ultrathin perovskite films

DOEpatents

Rappe, Andrew M; Kolpak, Alexie Michelle

2013-12-10

Disclosed herein are perovskite ferroelectric thin-film. Also disclosed are methods of controlling the properties of ferroelectric thin films. These films can be used in a variety materials and devices, such as catalysts and storage media, respectively.

Characteristics of ITO films with oxygen plasma treatment for thin film solar cell applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Yong Seob; Kim, Eungkwon; Hong, Byungyou

2013-12-15

Graphical abstract: The effect of O{sub 2} plasma treatment on the surface and the work function of ITO films. - Highlights: • ITO films were prepared on the glass substrate by RF magnetron sputtering method. • Effects of O{sub 2} plasma treatment on the properties of ITO films were investigated. • The work function of ITO film was changed from 4.67 to 5.66 eV by plasma treatment. - Abstract: The influence of oxygen plasma treatment on the electro-optical and structural properties of indium-tin-oxide films deposited by radio frequency magnetron sputtering method were investigated. The films were exposed at different O{submore » 2} plasma powers and for various durations by using the plasma enhanced chemical vapor deposition (PECVD) system. The resistivity of the ITO films was almost constant, regardless of the plasma treatment conditions. Although the optical transmittance of ITO films was little changed by the plasma power, the prolonged treatment slightly increased the transmittance. The work function of ITO film was changed from 4.67 eV to 5.66 eV at the plasma treatment conditions of 300 W and 60 min.« less

Formation of Ohmic contact to semipolar (11-22) p-GaN by electrical breakdown method

NASA Astrophysics Data System (ADS)

Jeong, Seonghoon; Lee, Sung-Nam; Kim, Hyunsoo

2018-01-01

The electrical breakdown (EBD) method was used to obtain Ohmic contact to semipolar (11-20) p-GaN surfaces using the Ti/SiO2/ p-GaN structure. The EBD method by which the electrical stress voltage was increased up to 70 V with a compliance current of 30 mA resulted in an Ohmic contact with a specific contact resistance of 3.1×10-3 Ωcm2. The transmission electron microscope (TEM) analysis revealed that the oxygen was slightly out-diffused from SiO2 layer toward Ti surface and the oxidation occurred at the Ti surface, while the GaN remained unchanged.

Filming The Man Hunters

ERIC Educational Resources Information Center

Hockings, Paul

1976-01-01

"The Man Hunters" is a film about paleoanthropology. This article is a personal account of how the film was put together using anthropological knowledge and numerous anthropologists and how the film was received by the American public. (Author)

Piezoelectric Motion of Multilayer Film with Alternate Rows of Optical Isomers of Chiral Polymer Film

NASA Astrophysics Data System (ADS)

Yoshida, Tetsuo; Imoto, Kenji; Nakai, Takaaki; Uwami, Ryouta; Kataoka, Takuya; Inoue, Masataka; Fukumoto, Takahiro; Kamimura, Yuuki; Kato, Atsuko; Tajitsu, Yoshiro

2011-09-01

We realized a multilayer film laminated alternately with poly(L-lactic acid) (PLLA) and poly(D-lactic acid) (PDLA) films in order to improve the piezoelectric performance of the PLLA film. In the fabrication processes, the thicknesses of PLLA and PDLA films were reduced to improve the effective electric field, and a multilayer composed of more than 100 layers (PDLA/PLLA multilayer film) was realized to improve the piezoelectric performance. In general, a single PLLA film has a piezoelectric constant of about 5 pC/N, and it is difficult to observe the piezoelectric resonance in this film of centimeter-order size using a commercial impedance analyzer because of its small Q-value. In contrast, the PDLA/PLLA multilayer film of centimeter-order size has a piezoelectric performance equivalent to that of the piezoelectric material with a piezoelectric constant of 100 pC/N, and also, the piezoelectric resonance can be observed in this film. On the basis of these results, we confirmed that even an object of 259 g mass is made to vibrate under the piezoelectric resonance vibration of this PDLA/PLLA multilayer film. In other words, necessary quantities for actual work as an actuator could be obtained in the PDLA/PLLA multilayer film.

Statics of wrinkling films

NASA Technical Reports Server (NTRS)

Zak, M.

1982-01-01

An analytical investigation of the equilibrium of wrinkling films is conducted. Zak (1979) has shown that wrinkling occurs in connection with the instability of a smooth film having no resistance to bending in the case of compression. The governing equation for the equilibrium of a film with possible regions of wrinkling is considered. The introduction of fictitious stress reduces the governing equation to a form which formally coincides with the governing equation for a string. Equilibrium conditions in the case of an absence of external forces are explored, taking into account the stretching of a semispherical film, the torsion of a convex film of revolution, and stress singularities. A study is conducted of the equilibrium under conditions in which external forces normal to the surface of a film are present. Attention is also given to the equilibrium in a potential field.

Thin-film optical initiator

DOEpatents

Erickson, Kenneth L.

2001-01-01

A thin-film optical initiator having an inert, transparent substrate, a reactive thin film, which can be either an explosive or a pyrotechnic, and a reflective thin film. The resultant thin-film optical initiator system also comprises a fiber-optic cable connected to a low-energy laser source, an output charge, and an initiator housing. The reactive thin film, which may contain very thin embedded layers or be a co-deposit of a light-absorbing material such as carbon, absorbs the incident laser light, is volumetrically heated, and explodes against the output charge, imparting about 5 to 20 times more energy than in the incident laser pulse.

Pyrolyzed thin film carbon

NASA Technical Reports Server (NTRS)

Harder, Theodore (Inventor); Konishi, Satoshi (Inventor); Miserendino, Scott (Inventor); Tai, Yu-Chong (Inventor); Liger, Matthieu (Inventor)

2010-01-01

A method of making carbon thin films comprises depositing a catalyst on a substrate, depositing a hydrocarbon in contact with the catalyst and pyrolyzing the hydrocarbon. A method of controlling a carbon thin film density comprises etching a cavity into a substrate, depositing a hydrocarbon into the cavity, and pyrolyzing the hydrocarbon while in the cavity to form a carbon thin film. Controlling a carbon thin film density is achieved by changing the volume of the cavity. Methods of making carbon containing patterned structures are also provided. Carbon thin films and carbon containing patterned structures can be used in NEMS, MEMS, liquid chromatography, and sensor devices.

Quantification of Marangoni flows and film morphology during solid film formation by inkjet printing

NASA Astrophysics Data System (ADS)

Ishizuka, Hirotaka; Fukai, Jun

2018-01-01

We visualized experimentally the internal flow inside inkjet droplets of polystyrene-anisole solution during solid film formation on substrates at room temperature. The effects of contact angle and evaporation rate on the internal flow and film morphology were quantitatively investigated. The transport process during film formation was examined by measuring the relationship between internal flow and film morphology, which provided three remarkable findings. First, self-pinning and the strength of outward flow on the free surface under 2.3 Pa s determined film morphology. The solute distribution, corresponding to rim areas in ring-like films and a convex trough in dot-like films, had already developed at self-pinning. Second, the mass fraction at self-pinning close to the contact line converged to one, regardless of the film morphology. This implies that self-pinning is independent of parameters such as the contact angle and evaporation rate. Third, at room temperature, the solutal Marangoni numbers were 20-30 times larger than the thermal ones. Thus, the outward flow on the free surface caused by the solutal Marangoni effect dominates in droplets before self-pinning. The solutal Marangoni number at self-pinning and thickness variation at the center of the film displayed a good relationship for droplets with different contact angles and evaporation rates. This suggests that film morphology can be technically controlled by solutal Marangoni number at room temperature.

Film thickness for different regimes of fluid-film lubrication

NASA Technical Reports Server (NTRS)

Hamrock, B. J.

1980-01-01

Film thickness equations are provided for four fluid-film lubrication regimes found in elliptical contacts. These regimes are isoviscous-rigid; viscous-rigid; elastohydrodynamic lubrication of low-elastic-modulus materials (soft EHL), or isoviscous-elastic; and elastohydrodynamic lubrication of high-elastic-modulus materials (hard EHL), or viscous-elastic. The influence or lack of influence of elastic and viscous effects is the factor that distinguishes these regimes. The results are presented as a map of the lubrication regimes, with film thickness contours on a log-log grid of the viscosity and elasticity for three values of the ellipticity parameter.

Molecular films associated with LDEF

NASA Technical Reports Server (NTRS)

Crutcher, E. R.; Warner, K. J.

1992-01-01

The molecular films deposited on the surface of the Long Duration Exposure Facility (LDEF) originated from the paints and room-temperature-vulcanized (RTV) silicone materials intentionally used on the satellite and not from residual contaminants. The high silicone content of most of the films and the uniformity of the films indicates a homogenization process in the molecular deposition and suggests a chemically most favored composition for the final film. The deposition on interior surfaces and vents indicated multiple bounce trajectories or repeated deposition-reemission cycles. Exterior surface deposits indicated a significant return flux. Ultraviolet light exposure was required to fix the deposited film as is indicated by the distribution of the films on interior surfaces and the thickness of films at the vent locations. Thermal conditions at the time of exposure to ultraviolet light seems to be an important factor in the thickness of the deposit. Sunrise facing (ram direction) surfaces always had the thicker film. These were the coldest surfaces at the time of their exposure to ultraviolet light. The films have a layered structure suggesting cyclic deposition. As many as 34 distinct layers were seen in the films. The cyclic nature of the deposition and the chemical uniformity of the film one layer to the next suggest an early deposition of the films though there is evidence for the deposition of molecular films throughout the nearly six year exposure of the satellite. A final 'spray' of an organic material associated with water soluble salts occurred very late in the mission. This may have been the result of one of the shuttle dump activities.

Ellipsometry of anodic film growth

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, C.G.

1978-08-01

An automated computer interpretation of ellisometer measurements of anodic film growth was developed. Continuous mass and charge balances were used to utilize more fully the time dependence of the ellipsometer data and the current and potential measurements. A multiple-film model was used to characterize the growth of films which proceeds via a dissolution--precipitation mechanism; the model also applies to film growth by adsorption and nucleation mechanisms. The characteristic parameters for film growth describe homogeneous and heterogeneous crystallization rates, film porosities and degree of hydration, and the supersaturation of ionic species in the electrolyte. Additional descriptions which may be chosen aremore » patchwise film formation, nonstoichiometry of the anodic film, and statistical variations in the size and orientation of secondary crystals. Theories were developed to describe the optical effects of these processes. An automatic, self-compensating ellipsometer was used to study the growth in alkaline solution of anodic films on silver, cadmium, and zinc. Mass-transport conditions included stagnant electrolyte and forced convection in a flow channel. Multiple films were needed to characterize the optical properties of these films. Anodic films grew from an electrolyte supersatuated in the solution-phase dissolution product. The degree of supersaturation depended on transport conditions and had a major effect on the structure of the film. Anodic reaction rates were limited by the transport of charge carriers through a primary surface layer. The primary layers on silver, zinc, and cadmium all appeared to be nonstoichiometric, containing excess metal. Diffusion coefficients, transference numbers, and the free energy of adsorption of zinc oxide were derived from ellipsometer measurements. 97 figures, 13 tables, 198 references.« less

Film Language.

ERIC Educational Resources Information Center

Hudlin, Edward W.

1979-01-01

The author briefly surveys some of the claims made about the presumed nature of film as language and some of the problems that arise. He considers the views of two influential schools of film criticism: the Russian formalists (Pudovkin and Eisenstein) and the British semiologist (Peter Wollen). (Author/SJL)

Flight test comparison of film type SO-289 and film type 2424 in the AMPS camera

NASA Technical Reports Server (NTRS)

Perry, L.

1975-01-01

A flight test was conducted to determine the suitability of SO-289 multispectral infrared aerial film for Earth Resources' use. It was directly compared to film type 2424, infrared aerographic film, the IR film in current use. The exposure parameters for both films are given.

Ratings for emotion film clips.

PubMed

Gabert-Quillen, Crystal A; Bartolini, Ellen E; Abravanel, Benjamin T; Sanislow, Charles A

2015-09-01

Film clips are widely utilized to elicit emotion in a variety of research studies. Normative ratings for scenes selected for these purposes support the idea that selected clips correspond to the intended target emotion, but studies reporting normative ratings are limited. Using an ethnically diverse sample of college undergraduates, selected clips were rated for intensity, discreteness, valence, and arousal. Variables hypothesized to affect the perception of stimuli (i.e., gender, race-ethnicity, and familiarity) were also examined. Our analyses generally indicated that males reacted strongly to positively valenced film clips, whereas females reacted more strongly to negatively valenced film clips. Caucasian participants tended to react more strongly to the film clips, and we found some variation by race-ethnicity across target emotions. Finally, familiarity with the films tended to produce higher ratings for positively valenced film clips, and lower ratings for negatively valenced film clips. These findings provide normative ratings for a useful set of film clips for the study of emotion, and they underscore factors to be considered in research that utilizes scenes from film for emotion elicitation.

Phantom evaluation of the effect of film processing on mammographic screen-film combinations.

PubMed

McLean, D; Rickard, M T

1994-08-01

Mammographic image quality should be optimal for diagnosis, and the film contrast can be manipulated by altering development parameters. In this study phantom test objects were radiographed and processed for a given range of developer temperatures and times for four film-screen systems. Radiologists scored the phantom test objects on the resultant films to evaluate the effect on diagnosis of varying image contrast. While for three film-screen systems processing led to appreciable contrast differences, for only one film system did maximum contrast correspond with optimal phantom test object scoring. The inability to show an effect on diagnosis in all cases is possibly due to the variation in radiologist responses found in this study and in normal clinical circumstances. Other technical factors such as changes in film fog, grain and mottle may contribute to the study findings.

36 CFR § 704.1 - Films selected for inclusion in the National Film Registry.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true Films selected for inclusion in the National Film Registry. § 704.1 Section § 704.1 Parks, Forests, and Public Property LIBRARY OF CONGRESS NATIONAL FILM REGISTRY OF THE LIBRARY OF CONGRESS § 704.1 Films selected for inclusion in...

Clinical careers film.

PubMed

2015-09-01

Those interested in developing clinical academic careers might be interested in a short animated film by Health Education England (HEE) and the National Institute for Health Research. The three-minute film, a frame from which is shown below, describes the sort of opportunities that are on offer to all professionals as part of the HEE's clinical academic careers framework. You can view the film on YouTube at tinyurl.com/pelb95c.

Organic Photovoltaic Devices Based on Oriented n-Type Molecular Films Deposited on Oriented Polythiophene Films.

PubMed

Mizokuro, Toshiko; Tanigaki, Nobutaka; Miyadera, Tetsuhiko; Shibata, Yousei; Koganezawa, Tomoyuki

2018-04-01

The molecular orientation of π-conjugated molecules has been reported to significantly affect the performance of organic photovoltaic devices (OPVs) based on molecular films. Hence, the control of molecular orientation is a key issue toward the improvement of OPV performance. In this research, oriented thin films of an n-type molecule, 3,4,9,10-Perylenetetracarboxylic Bisbenzimida-zole (PTCBI), were formed by deposition on in-plane oriented polythiophene (PT) films. Orientation of the PTCBI films was evaluated by polarized UV-vis spectroscopy and 2D-Grazing incidence X-ray diffraction. Results indicated that PTCBI molecules on PT film exhibit nearly edge-on and in-plane orientation (with molecular long axis along the substrate), whereas PTCBI molecules without PT film exhibit neither. OPVs composed of PTCBI molecular film with and without PT were fabricated and evaluated for correlation of orientation with performance. The OPVs composed of PTCBI film with PT showed higher power conversion efficiency (PCE) than that of film without PT. The experiment indicated that in-plane orientation of PTCBI molecules absorbs incident light more efficiently, leading to increase in PCE.

US/Russian Joint Film Test

NASA Technical Reports Server (NTRS)

Slater, Richard

1996-01-01

A joint U.S./Russian film test was conducted during MIR Mission 18 to evaluate the effects of radiation on photographic film during long-duration space flights. Two duplicate sets of film were flown on this MIR mission: one set was processed and evaluated by the NASA/JSC Photographic Laboratory, and the other by the RKK Energia's Photographic Laboratory in Moscow. This preliminary report includes only the results of the JSC evaluation (excluding the SN-10 film which was not available for evaluation at the time this report was written). The final report will include an evaluation by JSC of the SN-10 film and an evaluation of the test data by the RKK Energia. ISC's evaluation of the test data showed the positive film flown was damaged very little when exposed to approximately 8 rads of radiation. Two of the three negative films were significantly damaged and the third film was damaged only moderately.

US/Russian Joint Film Test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slater, R.

1996-04-01

A joint U.S./Russian film test was conducted during MIR Mission 18 to evaluate the effects of radiation on photographic film during long-duration space flights. Two duplicate sets of film were flown on this MIR mission: one set was processed and evaluated by the NASA/JSC Photographic Laboratory, and the other by the RKK Energia`s Photographic Laboratory in Moscow. This preliminary report includes only the results of the JSC evaluation (excluding the SN-10 film which was not available for evaluation at the time this report was written). The final report will include an evaluation by JSC of the SN-10 film and anmore » evaluation of the test data by the RKK Energia. ISC`s evaluation of the test data showed the positive film flown was damaged very little when exposed to approximately 8 rads of radiation. Two of the three negative films were significantly damaged and the third film was damaged only moderately.« less

High-throughput characterization of film thickness in thin film materials libraries by digital holographic microscopy.

PubMed

Lai, Yiu Wai; Krause, Michael; Savan, Alan; Thienhaus, Sigurd; Koukourakis, Nektarios; Hofmann, Martin R; Ludwig, Alfred

2011-10-01

A high-throughput characterization technique based on digital holography for mapping film thickness in thin-film materials libraries was developed. Digital holographic microscopy is used for fully automatic measurements of the thickness of patterned films with nanometer resolution. The method has several significant advantages over conventional stylus profilometry: it is contactless and fast, substrate bending is compensated, and the experimental setup is simple. Patterned films prepared by different combinatorial thin-film approaches were characterized to investigate and demonstrate this method. The results show that this technique is valuable for the quick, reliable and high-throughput determination of the film thickness distribution in combinatorial materials research. Importantly, it can also be applied to thin films that have been structured by shadow masking.

Thin Cu film resistivity using four probe techniques: Effect of film thickness and geometrical shapes

NASA Astrophysics Data System (ADS)

Choudhary, Sumita; Narula, Rahul; Gangopadhyay, Subhashis

2018-05-01

Precise measurement of electrical sheet resistance and resistivity of metallic thin Cu films may play a significant role in temperature sensing by means of resistivity changes which can further act as a safety measure of various electronic devices during their operation. Four point probes resistivity measurement is a useful approach as it successfully excludes the contact resistance between the probes and film surface of the sample. Although, the resistivity of bulk samples at a particular temperature mostly depends on its materialistic property, however, it may significantly differ in the case of thin films, where the shape and thickness of the sample can significantly influence on it. Depending on the ratio of the film thickness to probe spacing, samples are usually classified in two segments such as (i) thick films or (ii) thin films. Accordingly, the geometric correction factors G can be related to the sample resistivity r, which has been calculated here for thin Cu films of thickness up to few 100 nm. In this study, various rectangular shapes of thin Cu films have been used to determine the shape induced geometric correction factors G. An expressions for G have been obtained as a function of film thickness t versus the probe spacing s. Using these expressions, the correction factors have been plotted separately for each cases as a function of (a) film thickness for fixed linear probe spacing and (b) probe distance from the edge of the film surface for particular thickness. Finally, we compare the experimental results of thin Cu films of various rectangular geometries with the theoretical reported results.

Atomic-Layer-Deposition of Indium Oxide Nano-films for Thin-Film Transistors.

PubMed

Ma, Qian; Zheng, He-Mei; Shao, Yan; Zhu, Bao; Liu, Wen-Jun; Ding, Shi-Jin; Zhang, David Wei

2018-01-09

Atomic-layer-deposition (ALD) of In 2 O 3 nano-films has been investigated using cyclopentadienyl indium (InCp) and hydrogen peroxide (H 2 O 2 ) as precursors. The In 2 O 3 films can be deposited preferentially at relatively low temperatures of 160-200 °C, exhibiting a stable growth rate of 1.4-1.5 Å/cycle. The surface roughness of the deposited film increases gradually with deposition temperature, which is attributed to the enhanced crystallization of the film at a higher deposition temperature. As the deposition temperature increases from 150 to 200 °C, the optical band gap (E g ) of the deposited film rises from 3.42 to 3.75 eV. In addition, with the increase of deposition temperature, the atomic ratio of In to O in the as-deposited film gradually shifts towards that in the stoichiometric In 2 O 3 , and the carbon content also reduces by degrees. For 200 °C deposition temperature, the deposited film exhibits an In:O ratio of 1:1.36 and no carbon incorporation. Further, high-performance In 2 O 3 thin-film transistors with an Al 2 O 3 gate dielectric were achieved by post-annealing in air at 300 °C for appropriate time, demonstrating a field-effect mobility of 7.8 cm 2 /V⋅s, a subthreshold swing of 0.32 V/dec, and an on/off current ratio of 10 7 . This was ascribed to passivation of oxygen vacancies in the device channel.

NFL Films audio, video, and film production facilities

NASA Astrophysics Data System (ADS)

Berger, Russ; Schrag, Richard C.; Ridings, Jason J.

2003-04-01

The new NFL Films 200,000 sq. ft. headquarters is home for the critically acclaimed film production that preserves the NFL's visual legacy week-to-week during the football season, and is also the technical plant that processes and archives football footage from the earliest recorded media to the current network broadcasts. No other company in the country shoots more film than NFL Films, and the inclusion of cutting-edge video and audio formats demands that their technical spaces continually integrate the latest in the ever-changing world of technology. This facility houses a staggering array of acoustically sensitive spaces where music and sound are equal partners with the visual medium. Over 90,000 sq. ft. of sound critical technical space is comprised of an array of sound stages, music scoring stages, audio control rooms, music writing rooms, recording studios, mixing theaters, video production control rooms, editing suites, and a screening theater. Every production control space in the building is designed to monitor and produce multi channel surround sound audio. An overview of the architectural and acoustical design challenges encountered for each sophisticated listening, recording, viewing, editing, and sound critical environment will be discussed.

Optical and structural properties of sputtered CdS films for thin film solar cell applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Donguk; Park, Young; Kim, Minha

2015-09-15

Graphical abstract: Photo current–voltage curves (a) and the quantum efficiency (QE) (b) for the solar cell with CdS film grown at 300 °C. - Highlights: • CdS thin films were grown by a RF magnetron sputtering method. • Influence of growth temperature on the properties of CdS films was investigated. • At higher T{sub g}, the crystallinity of the films improved and the grains enlarged. • CdS/CdTe solar cells with efficiencies of 9.41% were prepared at 300 °C. - Abstract: CdS thin films were prepared by radio frequency magnetron sputtering at various temperatures. The effects of growth temperature on crystallinity,more » surface morphology and optical properties of the films were characterized with X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Raman spectra, UV–visible spectrophotometry, and photoluminescence (PL) spectra. As the growth temperature was increased, the crystallinity of the sputtered CdS films was improved and the grains were enlarged. The characteristics of CdS/CdTe thin film solar cell appeared to be significantly influenced by the growth temperature of the CdS films. Thin film CdS/CdTe solar cells with efficiencies of 9.41% were prepared at a growth temperature of 300 °C.« less

Multiresonant layered plasmonic films

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeVetter, Brent M.; Bernacki, Bruce E.; Bennett, Wendy D.

Multi-resonant nanoplasmonic films have numerous applications in areas such as nonlinear optics, sensing, and tamper indication. While techniques such as focused ion beam milling and electron beam lithography can produce high-quality multi-resonant films, these techniques are expensive, serial processes that are difficult to scale at the manufacturing level. Here, we present the fabrication of multi-resonant nanoplasmonic films using a layered stacking technique. Periodically-spaced gold nanocup substrates were fabricated using self-assembled polystyrene nanospheres followed by oxygen plasma etching and metal deposition via magnetron sputter coating. By adjusting etch parameters and initial nanosphere size, it was possible to achieve an optical responsemore » ranging from the visible to the near-infrared. Singly resonant, flexible films were first made by performing peel-off using an adhesive-coated polyolefin film. Through stacking layers of the nanofilm, we demonstrate fabrication of multi-resonant films at a fraction of the cost and effort as compared to top-down lithographic techniques.« less

TAMPERPROOF FILM BADGE

DOEpatents

Kocher, L.F.

1958-10-01

A persornel dosimeter film badge made of plastic, with provision for a picture of the wearer and an internal slide containing photographic film that is sensitive to various radiations, is described. Four windows made of differing material selectively attenuate alpha, beta, gamma rays, and neutrons so as to distinguish the particular type of radiation the wearer was subjected to. In addition, a lead shield has the identification number of the wearer perforated thereon so as to identify the film after processing. An internal magnetically actuated latch securely locks the slide within the body, and may be withdrawn only upon the external application of two strong magnetic forces in order to insure that the wearer or other curious persons will not accidentally expose the film to visual light.

Some Suggestions for Conducting Film Competitions and Film Festivals.

ERIC Educational Resources Information Center

Eastman Kodak Co., Rochester, NY.

Four essentials in staging film festivals and competitions are: facilities, films, equipment, and an audience. Basic steps in getting these essentials together are outlined. Surveying available facilities first helps you gauge the scale of the festival, estimate the likely costs and receipts, and plan for the projection equipment necessary.…

Film-Making and the Curriculum.

ERIC Educational Resources Information Center

Schwartz, Elizabeth

A guide to filmmaking techniques and the use of class-made films in the curriculum covers techniques of both animated and live-action films. The purposes of single concept, documentary, interpretive, and time-lapse films are discussed briefly. Production techniques covered include organization of personnel, scripting, filming, directing, editing,…

[Spectroscopic study on film formation mechanism and structure of composite silanes-V-Zr passive film].

PubMed

Wang, Lei; Liu, Chang-sheng; Shi, Lei; An, Cheng-qiang

2015-02-01

A composite silanes-V-Zr passive film was overlayed on hot-dip galvanized steel. Attenuated total reflection Fourier transformed infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectrometer (XPS) and radio frequency glow discharge optical emission spectrometry (rf-GD-OES) were used to characterize the molecular structure of the silanes-V-Zr passive film. The mechanism of film formation was discussed: The results show that the silane molecules are crosslinked as the main film former and inorganic inhibitor is even distributed in the film. The fitting peak of 100.7 eV in XPS single Si2p energy range spectra of the composite silanes-V-Zr passive film and the widening and strengthening of the Si--O infrared absorption peak at 1100 cm(-1) indicate that the silanes were adsorbed on the surface of zinc with chemical bond of Si--O--Zn, and the silane molecules were connected with each other by bond of Si--O--Si. Two characteristic absorption peaks of amide at 1650 and 1560 cm(-1) appear in the infrared spectroscopy of the composite silanes-V-Zr passive film, and a characteristic absorption peak of epoxy groups at 910 cm(-1) disappears in the infrared spectroscopy of the passive film. The results indicate that gamma-APT can be prepared through nucleophilic ring-opening of ethylene oxide in gamma-GPT molecule to form C--N covalent bonds. The rf-GD-OES results indicate that there is a oxygen enriched layer in 0.3 microm depth of the composite silanes-V-Zr passive film. Moreover, ZrF4, ZrO2 and some inorganic matter obtained by the reaction during the forming processof the composite silanes-V-Zr passive film are distributed evenly throughout the film. According to the film composition, the physical processes and chemical reactions during the film forming process were studied by using ATR-FTIR. Based on this, the film forming mechanism was proposed.

Predicting Film Genres with Implicit Ideals

PubMed Central

Olney, Andrew McGregor

2013-01-01

We present a new approach to defining film genre based on implicit ideals. When viewers rate the likability of a film, they indirectly express their ideal of what a film should be. Across six studies we investigate the category structure that emerges from likability ratings and the category structure that emerges from the features of film. We further compare these data-driven category structures with human annotated film genres. We conclude that film genres are structured more around ideals than around features of film. This finding lends experimental support to the notion that film genres are set of shifting, fuzzy, and highly contextualized psychological categories. PMID:23423823

Fire resistant films for aircraft applications

NASA Technical Reports Server (NTRS)

Kourtides, D. A.

1983-01-01

Alternative sandwich panel decorative films were investigated as replacements for the polyvinyl fluoride currently used in aircraft interiors. Candidate films were studied for flammability, smoke emission, toxic gas emission, flame spread, and suitability as a printing surface for the decorative acrylic ink system. Several of the candidate films tested were flame modified polyvinyl fluoride, polyvinylidene fluoride, polyimide, polyamide, polysulfone, polyphenylsulfone, polyethersulfone, polybenzimidazole, polycarbonate, polyparabanic acid, polyphosphazene, polyetheretherketon, and polyester. The films were evaluated as pure films only, films silk-screened with an acrylic ink, and films adhered to a phenolic fiberglass substrate. Films which exhibited the highest fire resistant properties included PEEK polyetheretherketon, Aramid polyamide, and ISO-BPE polyester.

Predicting film genres with implicit ideals.

PubMed

Olney, Andrew McGregor

2012-01-01

We present a new approach to defining film genre based on implicit ideals. When viewers rate the likability of a film, they indirectly express their ideal of what a film should be. Across six studies we investigate the category structure that emerges from likability ratings and the category structure that emerges from the features of film. We further compare these data-driven category structures with human annotated film genres. We conclude that film genres are structured more around ideals than around features of film. This finding lends experimental support to the notion that film genres are set of shifting, fuzzy, and highly contextualized psychological categories.

Rupture of vertical soap films

NASA Astrophysics Data System (ADS)

Rio, Emmanuelle

2014-11-01

Soap films are ephemeral and fragile objects. They tend to thin under gravity, which gives rise to the fascinating variations of colors at their interfaces but leads systematically to rupture. Even a child can create, manipulate and admire soap films and bubbles. Nevertheless, the reason why it suddenly bursts remains a mystery although the soap chosen to stabilize the film as well as the humidity of the air seem very important. One difficulty to study the rupture of vertical soap films is to control the initial solution. To avoid this problem we choose to study the rupture during the generation of the film at a controlled velocity. We have built an experiment, in which we measure the maximum length of the film together with its lifetime. The generation of the film is due to the presence of a gradient of surface concentration of surfactants at the liquid/air interface. This leads to a Marangoni force directed toward the top of the film. The film is expected to burst only when its weight is not balanced anymore by this force. We will show that this leads to the surprising result that the thicker films have shorter lifetimes than the thinner ones. It is thus the ability of the interface to sustain a surface concentration gradient of surfactants which controls its stability.

YBa2Cu3O7 thin films on nanocrystalline diamond films for HTSC bolometer

NASA Technical Reports Server (NTRS)

Cui, G.; Beetz, C. P., Jr.; Boerstler, R.; Steinbeck, J.

1993-01-01

Superconducting YBa2Cu3O(7-x) films on nanocrystalline diamond thin films have been fabricated. A composite buffer layer system consisting of diamond/Si3N4/YSZ/YBCO was explored for this purpose. The as-deposited YBCO films were superconducting with Tc of about 84 K and a relatively narrow transition width of about 8 K. SEM cross sections of the films showed very sharp interfaces between diamond/Si3N4 and between Si3N4/YSZ. The deposited YBCO film had a surface roughness of about 1000 A, which is suitable for high-temperature superconductive (HTSC) bolometer fabrication. It was also found that preannealing of the nanocrystalline diamond thin films at high temperature was very important for obtaining high-quality YBCO films.

Amorphous-Metal-Film Diffusion Barriers

NASA Technical Reports Server (NTRS)

Nicolet, M. A.

1987-01-01

Incorporation of N into Ni/W films reduces reactivity with Si substrate. Paper describes reactions between Si substrates and deposited amorphous Ni/W or Ni/N/W films. Thermal stability of amorphous Ni/W films as diffusion barriers in Si markedly improved by introduction of N into Ni/W films during deposition.

Children's Film Programming: A Handbook.

ERIC Educational Resources Information Center

Gallery Association of New York State, Inc.

Directed at the staffs of art institutions, community centers, libraries, historical societies, and schools, this practical guide is intended to help in the selection and use of films for children. "Film," in this handbook refers to 16mm films presented in public screenings--not videotape versions of films, and not material originally…

Film: The Reality of Being.

ERIC Educational Resources Information Center

Sheratsky, Rodney E.

The visual media, particularly film, has challenged today's educators by competing for students' time and interests and by providing a relevancy that books designed for school use do not have. Using film study to combat the supposed immorality of theatrical films and employing instructional film to transmit information has provided a negative…

Film Scriptwriting: A Practical Manual.

ERIC Educational Resources Information Center

Swain, Dwight V.

Dealing with both documentary and feature films, this book is a guide to using particular tools and procedures in developing ideas and concepts for writing film scripts. Part one deals with the factual, or documentary, film and discusses the proposal outline, film treatment, sequence outline, shooting script, and narration writing. Part two…

Professor Camillo Negro's Neuropathological Films.

PubMed

Chiò, Adriano; Gianetto, Claudia; Dagna, Stella

2016-01-01

Camillo Negro, Professor in Neurology at the University of Torino, was a pioneer of scientific film. From 1906 to 1908, with the help of his assistant Giuseppe Roasenda and in collaboration with Roberto Omegna, one of the most experienced cinematographers in Italy, he filmed some of his patients for scientific and educational purposes. During the war years, he continued his scientific film project at the Military Hospital in Torino, filming shell-shocked soldiers. In autumn 2011, the Museo Nazionale del Cinema, in partnership with the Faculty of Neurosciences of the University of Torino, presented a new critical edition of the neuropathological films directed by Negro. The Museum's collection also includes 16 mm footage probably filmed in 1930 by Doctor Fedele Negro, Camillo's son. One of these films is devoted to celebrating the effects of the so-called "Bulgarian cure" on Parkinson's disease.

Nonlinear Layer-by-Layer Films: Effects of Chain Diffusivity on Film Structure and Swelling

DOE PAGES

Selin, Victor; Ankner, John F.; Sukhishvili, Svetlana A.

2017-08-09

Here in this paper, we report on the role of molecular diffusivity in the formation of nonlinearly growing polyelectrolyte multilayers (nlPEMs). Electrostatically bound polyelectrolyte multilayers were assembled from poly(methacrylic acid) (PMAA) as a polyanion and quaternized poly(2-(dimethylamino)ethyl methacrylate) (QPC) as a polycation. Film growth as measured by ellipsometry was strongly dependent on the time allowed for each polymer deposition step, suggesting that the diffusivities of the components are crucial in controlling the rate of film growth. Uptake of polyelectrolytes within nlPEMs was relatively slow and occurred on time scales ranging from minutes to hours, depending on the film thickness. Spectroscopicmore » ellipsometry measurements with nlPEM films exposed to aqueous solutions exhibited high (severalfold) degrees of film swelling and different swelling values for films exposed to QPC or PMAA solutions. FTIR spectroscopy showed that the average ionization of film-assembled PMAA increased upon binding of QPC and decreased upon binding of PMAA, in agreement with the charge regulation mechanism for weak polyelectrolytes. The use of neutron reflectometry (NR) enabled quantification of chain intermixing within the film, which was drastically enhanced when longer times were allowed for polyelectrolyte deposition. Diffusion coefficients of the polycation derived from the uptake rates of deuterated chains within hydrogenated films were of the order of 10 –14 cm 2/s, i.e., 5–6 orders of magnitude smaller than those found for diffusion of free polymer chains in solution. Exchange of the polymer solutions to buffer inhibited film intermixing. Taken together, these results contribute to understanding the mechanism of the growth of nonlinear polyelectrolyte multilayers and demonstrate the possibility of controlling film intermixing, which is highly desirable for potential future applications.« less

Use of buffy coat thick films in detecting malaria parasites in patients with negative conventional thick films.

PubMed

Duangdee, Chatnapa; Tangpukdee, Noppadon; Krudsood, Srivicha; Wilairatana, Polrat

2012-04-01

To determine the frequency of malaria parasite detection from the buffy coat blood films by using capillary tube in falciparum malaria patients with negative conventional thick films. Thirty six uncomplicated falciparum malaria patients confirmed by conventional thick and thin films were included in the study. The patients were treated with artemisinin combination therapy at Hospital for Tropical Diseases, Bangkok, Thailand for 28 day. Fingerpricks for conventional blood films were conducted every 6 hours until negative parasitemia, then daily fingerpricks for parasite checks were conducted until the patients were discharged from hospital. Blood samples were also concurrently collected in 3 heparinized capillary tubes at the same time of fingerpricks for conventional blood films when the prior parasitemia was negative on thin films and parasitemia was lower than 50 parasites/200 white blood cells by thick film. The first negative conventional thick films were compared with buffy coat thick films for parasite identification. Out of 36 patients with thick films showing negative for asexual forms of parasites, buffy coat films could detect remaining 10 patients (27.8%) with asexual forms of Plasmodium falciparum. The study shows that buffy coat thick films are useful and can detect malarial parasites in 27.8% of patients whose conventional thick films show negative parasitemia.

Scale-up of water-based spider silk film casting using a film applicator.

PubMed

Agostini, Elisa; Winter, Gerhard; Engert, Julia

2017-10-30

Spider silk proteins for applications in drug delivery have attracted an increased interest during the past years. Some possible future medical applications for this biocompatible and biodegradable material are scaffolds for tissue engineering, implantable drug delivery systems and coatings for implants. Recently, we reported on the preparation of water-based spider silk films for drug delivery applications. In the current study, we describe the development of a manufacturing technique for casting larger spider silk films from aqueous solution employing a film applicator. Films were characterized in terms of morphology, water solubility, protein secondary structure, thermal stability, and mechanical properties. Different post-treatments were evaluated (phosphate ions, ethanol, steam sterilization and water vapor) to increase the content of β-sheets thereby achieving water insolubility of the films. Finally, the mechanical properties of the spider silk films were improved by incorporating 2-pyrrolidone as plasticizer. Copyright © 2017 Elsevier B.V. All rights reserved.

Composite polymeric film and method for its use in installing a very-thin polymeric film in a device

DOEpatents

Duchane, D.V.; Barthell, B.L.

1982-04-26

A composite polymeric film and a method for its use in forming and installing a very thin (< 10 ..mu..m) polymeric film are disclosed. The composite film consists of a thin film layer and a backing layer. The backing layer is soluble in a solvent in which the thin film layer is not soluble. In accordance with the method, the composite film is installed in a device in the same position in which it is sought to finally emplace the thin film. The backing layer is then selectiely dissolved in the solvent to leave the insoluble thin film layer as an unbacked film. The method permits a very thin film to e successfully installed in devices where the fragility of the film would preclude handling and installation by conventional methods.

Composite polymeric film and method for its use in installing a very thin polymeric film in a device

DOEpatents

Duchane, David V.; Barthell, Barry L.

1984-01-01

A composite polymeric film and a method for its use in forming and installing a very thin (<10 .mu.m) polymeric film are disclosed. The composite film consists of a thin film layer and a backing layer. The backing layer is soluble in a solvent in which the thin film layer is not soluble. In accordance with the method, the composite film is installed in a device in the same position in which it is sought to finally emplace the thin film. The backing layer is then selectively dissolved in the solvent to leave the insoluble thin film layer as an unbacked film. The method permits a very thin film to be successfully installed in devices where the fragility of the film would preclude handling and installation by conventional methods.

Predictors of Horror Film Attendance and Appeal: An Analysis of the Audience for Frightening Films.

ERIC Educational Resources Information Center

Tamborini, Ron; Stiff, James

1987-01-01

Analyzes the appeal of horror films. Develops a model that finds that important factors in the horror film's appeal are the audience's desire to experience the satisfying resolutions and to see the destruction usually found in these films and the sensation-seeking personality traits of audience members for these films. (NKA)

System for measuring film thickness

DOEpatents

Batishko, Charles R.; Kirihara, Leslie J.; Peters, Timothy J.; Rasmussen, Donald E.

1990-01-01

A system for determining the thicknesses of thin films of materials exhibiting fluorescence in response to exposure to excitation energy from a suitable source of such energy. A section of film is illuminated with a fixed level of excitation energy from a source such as an argon ion laser emitting blue-green light. The amount of fluorescent light produced by the film over a limited area within the section so illuminated is then measured using a detector such as a photomultiplier tube. Since the amount of fluorescent light produced is a function of the thicknesses of thin films, the thickness of a specific film can be determined by comparing the intensity of fluorescent light produced by this film with the intensity of light produced by similar films of known thicknesses in response to the same amount of excitation energy. The preferred embodiment of the invention uses fiber optic probes in measuring the thicknesses of oil films on the operational components of machinery which are ordinarily obscured from view.

Morphological Influence of Solution-Processed Zinc Oxide Films on Electrical Characteristics of Thin-Film Transistors.

PubMed

Lee, Hyeonju; Zhang, Xue; Hwang, Jaeeun; Park, Jaehoon

2016-10-19

We report on the morphological influence of solution-processed zinc oxide (ZnO) semiconductor films on the electrical characteristics of ZnO thin-film transistors (TFTs). Different film morphologies were produced by controlling the spin-coating condition of a precursor solution, and the ZnO films were analyzed using atomic force microscopy, X-ray diffraction, X-ray photoemission spectroscopy, and Hall measurement. It is shown that ZnO TFTs have a superior performance in terms of the threshold voltage and field-effect mobility, when ZnO crystallites are more densely packed in the film. This is attributed to lower electrical resistivity and higher Hall mobility in a densely packed ZnO film. In the results of consecutive TFT operations, a positive shift in the threshold voltage occurred irrespective of the film morphology, but the morphological influence on the variation in the field-effect mobility was evident. The field-effect mobility in TFTs having a densely packed ZnO film increased continuously during consecutive TFT operations, which is in contrast to the mobility decrease observed in the less packed case. An analysis of the field-effect conductivities ascribes these results to the difference in energetic traps, which originate from structural defects in the ZnO films. Consequently, the morphological influence of solution-processed ZnO films on the TFT performance can be understood through the packing property of ZnO crystallites.

AAAS Science Film Catalog.

ERIC Educational Resources Information Center

Seltz-Petrash, Ann, Ed.; Wolff, Kathryn, Ed.

Currently available American 16mm films in the areas of pure science, applied science and technology, and science and society are identified and listed. Included are films that are available from commercial, government, university, and industry producers. The first section of the catalog lists in Dewey Decimal order films intended for junior high…

Focus on Shakespearean Films.

ERIC Educational Resources Information Center

Eckert, Charles W., Ed.

This is an anthology of reviews and critical pieces of the significant and available Shakespearean films made between 1935 and 1966. Included are three general essays on Shakespearean film by Ian Johnson, Henri Lemaitre, and Geoffrey Reeves. The specific films and their reviewers are: A Midsummer's Night Dream (1935) Allardyce Nicoll and Richard…

[Psychopathology and film: a valuable interaction?].

PubMed

van Duppen, Z; Summa, M; Fuchs, T

2015-01-01

Film or film fragments are often used in psychopathology education. However, so far there have been very few articles that have discussed the benefits and limitations of using films to explain or illustrate psychopathology. Although numerous films involves psychopathology in varying degrees, it is not clear how we can use films for psychopathology education. To examine the advantages, limitations and possible methods of using film as a means of increasing our knowledge and understanding of psychiatric illnesses. We discuss five examples that illustrate the interaction of film and psychopathology. On the one hand we explain how the psychopathological concepts are used in each film and on the other hand we explain which aspects of each film are valuable aids for teaching psychopathology. The use of film makes it possible to introduce the following topics in psychopathological teaching programme: holistic psychiatric reasoning, phenomenology and the subjective experience, the recognition of psychopathological prototypes and the importance of context. There is undoubtedly an analogy between the method we have chosen for teaching psychopathology with the help of films and the holistic approach of the psychiatrist and his or her team. We believe psychopathology education can benefit from films and we would recommend our colleagues to use it in this way.

The Art of the Film.

ERIC Educational Resources Information Center

Lindgren, Ernest

The author prefaces his consideration of films as an art form with a discussion of the mechanics of filmmaking. He describes the division of talent on a movie set, details the history of the tools of filmmakers, and explains the production and reproduction of a film. The influence of film techniques on plot development in a fiction film is…

Lifelong Learning Films; 1972-1973.

ERIC Educational Resources Information Center

California Univ., Berkeley. Media Extension Center.

Over 450 newly acquired films are described in this brochure. They are, for the most part, short black-and-white 16 mm films produced by the University of California Extension Media Center and selected films from other producers. The main entry section arranges the films alphabetically by title; it gives an annotation, the running time,…

Engineering Graphene Films from Coal

NASA Astrophysics Data System (ADS)

Vijapur, Santosh H.

Graphene is a unique material with remarkable properties suitable for a wide array of applications. Chemical vapor deposition (CVD) is a simple technique for synthesis of large area and high quality graphene films on various metal substrates. Among the metal substrates, copper has been shown to be an excellent support for the growth of graphene films. Traditionally, hydrocarbon gases are used for the graphene synthesis via CVD. Unconventional solid carbon sources such as various polymers and food waste have also shown great potential for synthesis of graphene films. Coal is one such carbon enriched and abundantly available unconventional source. Utilization of coal as a carbon source to synthesize large area, transparent, and high quality few-layer graphene films via CVD has been demonstrated in the present work. Hydrocarbon gases are released as products of coal pyrolysis at temperatures ≥400 °C. This study hypothesized that, these hydrocarbon gases act as precursors for the synthesis of graphene films on the copper substrate. Hence, atmospheric pressure CVD and low temperature of 400 °C were utilized initially for the production of graphene films. These conditions were suitable for the formation of amorphous carbon (a-C) films but not crystalline graphene films that were the objective of this work. The synthesized a-C films on the copper substrate were shown to be uniform and transparent with large surface area. The thickness and surface roughness of the a-C films were determined to have typical values of 5 nm and 0.55 nm, respectively. The a-C film has >95 % optical transmittance and sheet resistivity of 0.6 MO sq-1. These values are comparable to other carbon thin films synthesized at higher temperatures. Further, the a-C films were transferred onto any type of substrate such as silicon wafer and titanium foil, and can be utilized for diverse applications. However, crystalline graphene films were not produced by implementing atmospheric pressure CVD and low

Thin film superconductor magnetic bearings

DOEpatents

Weinberger, Bernard R.

1995-12-26

A superconductor magnetic bearing includes a shaft (10) that is subject to a load (L) and rotatable around an axis of rotation, a magnet (12) mounted to the shaft, and a stator (14) in proximity to the shaft. The stator (14) has a superconductor thin film assembly (16) positioned to interact with the magnet (12) to produce a levitation force on the shaft (10) that supports the load (L). The thin film assembly (16) includes at least two superconductor thin films (18) and at least one substrate (20). Each thin film (18) is positioned on a substrate (20) and all the thin films are positioned such that an applied magnetic field from the magnet (12) passes through all the thin films. A similar bearing in which the thin film assembly (16) is mounted on the shaft (10) and the magnet (12) is part of the stator (14) also can be constructed.

Method for making carbon films

DOEpatents

Tan, M.X.

1999-07-29

A method for treating an organic polymer material, preferably a vinylidene chloride/vinyl chloride copolymer (Saran) to produce a flat sheet of carbon film material having a high surface area ([approx equal]1000 m[sup 2] /g) suitable as an electrode material for super capacitor applications. The method comprises heating a vinylidene chloride/vinyl chloride copolymer film disposed between two spaced apart graphite or ceramic plates to a first temperature of about 160 C for about 14 hours to form a stabilized vinylidene chloride/vinyl chloride polymer film, thereafter heating the stabilized film to a second temperature of about 750 C in an inert atmosphere for about one hour to form a carbon film; and finally activating the carbon film to increase the surface area by heating the carbon film in an oxidizing atmosphere to a temperature of at least 750--850 C for between 1--6 hours. 2 figs.

Method for making carbon films

DOEpatents

Tan, Ming X.

1999-01-01

A method for treating an organic polymer material, preferably a vinylidene chloride/vinyl chloride copolymer (Saran) to produce a flat sheet of carbon film material having a high surface area (.apprxeq.1000 m.sup.2 /g) suitable as an electrode material for super capacitor applications. The method comprises heating a vinylidene chloride/vinyl chloride copolymer film disposed between two spaced apart graphite or ceramic plates to a first temperature of about 160.degree. C. for about 14 hours to form a stabilized vinylidene chloride/vinyl chloride polymer film, thereafter heating the stabilized film to a second temperature of about 750.degree. C. in an inert atmosphere for about one hour to form a carbon film; and finally activating the carbon film to increase the surface area by heating the carbon film in an oxidizing atmosphere to a temperature of at least 750-850.degree. C. for between 1-6 hours.

Evidence-based dentistry skill acquisition by second-year dental students.

PubMed

Marshall, T A; McKernan, S C; Straub-Morarend, C L; Guzman-Armstrong, S; Marchini, L; Handoo, N Q; Cunningham, M A

2018-05-22

Identification and assessment of Evidence-based dentistry (EBD) outcomes have been elusive. Our objective was to describe EBD skill acquisition during the second (D2) year of pre-doctoral dental education and student competency at the end of the year. The first and fourth (final) curricular-required EBD Exercises (ie, application of the first 4 steps of the 5-Step evidence-based practice process applied to a real or hypothetical situation) completed by D2 students (n = 151) during 2014-2015 and 2015-2016 were evaluated to measure skill acquisition through use of a novel rubric with measures of performance from novice to expert. Exercises were evaluated on the performance for each step, identification of manuscript details and reflective commentary on manuscript components. Changes in performance were evaluated using the chi-square test for trend and the Wilcoxon signed-rank test. Seventy-eight per cent of students scored competent or higher on the Ask step at the beginning of the D2 year; scores improved with 58% scoring proficient or expert on the fourth Exercise (P < .001). Most students were advanced beginners or higher in the Acquire, Appraise and Apply steps at the beginning of the D2 year, with minimal growth observed during the year. Identification of manuscript details improved between the first and fourth Exercises (P = .015); however, depth of commentary skills did not change. Unlike previous investigations evaluating EBD knowledge or behaviour in a testing situation, we evaluated skill acquisition using applied Exercises. Consistent with their clinical and scientific maturity, D2 students minimally performed as advanced beginners at the end of their D2 year. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Metschnikowia drakensbergensis sp. nov. and Metschnikowia caudata sp. nov., endemic yeasts associated with Protea flowers in South Africa.

PubMed

de Vega, Clara; Guzmán, Beatriz; Steenhuisen, Sandy-Lynn; Johnson, Steven D; Herrera, Carlos M; Lachance, Marc-André

2014-11-01

In a taxonomic study of yeasts recovered from nectar of flowers and associated insects in South Africa, 11 strains were found to represent two novel species. Morphological and physiological characteristics and sequence analyses of the large-subunit rRNA gene D1/D2 region, as well as the actin, RNA polymerase II and elongation factor 2 genes, showed that the two novel species belonged to the genus Metschnikowia. Metschnikowia drakensbergensis sp. nov. (type strain EBD-CdVSA09-2(T) =CBS 13649(T) =NRRL Y-63721(T); MycoBank no. MB809688; allotype EBD-CdVSA10-2(A) =CBS13650(A) =NRRL Y-63720(A)) was recovered from nectar of Protea roupelliae and the beetle Heterochelus sp. This species belongs to the large-spored Metschnikowia clade and is closely related to Metschnikowia proteae, with which mating reactions and single-spored asci were observed. Metschnikowia caudata sp. nov. (type strain EBD-CdVSA08-1(T) =CBS 13651(T) =NRRL Y-63722(T); MycoBank no. MB809689; allotype EBD-CdVSA57-2(A) =CBS 13729(A) =NRRL Y-63723(A)) was isolated from nectar of Protea dracomontana, P. roupelliae and P. subvestita and a honeybee, and is a sister species to Candida hainanensis and Metschnikowia lopburiensis. Analyses of the four sequences demonstrated the existence of three separate phylotypes. Intraspecies matings led to the production of mature asci of unprecedented morphology, with a long, flexuous tail. A single ascospore was produced in all compatible crosses, regardless of sequence phylotype. The two species appear to be endemic to South Africa. The ecology and habitat specificity of these novel species are discussed in terms of host plant and insect host species. © 2014 IUMS.

Esophageal triamcinolone acetonide-filling method: a novel procedure to prevent stenosis after extensive esophageal endoscopic submucosal dissection (with videos).

PubMed

Shibagaki, Kotaro; Ishimura, Norihisa; Oshima, Naoki; Mishiro, Tsuyoshi; Fukuba, Nobuhiko; Tamagawa, Yuji; Yamashita, Noritsugu; Mikami, Hironobu; Izumi, Daisuke; Taniguchi, Hideaki; Sato, Shuichi; Ishihara, Shunji; Kinoshita, Yoshikazu

2018-02-01

Endoscopic submucosal dissection (ESD) for extensive esophageal carcinomas may cause severe stenosis requiring endoscopic balloon dilations (EBDs). A standard prevention method has not been established. We propose the esophageal triamcinolone acetonide (TA)-filling method as a novel local steroid administration procedure. We enrolled 22 consecutive patients with early esophageal cancer who were treated using either subcircumferential or circumferential ESD (15 and 7 procedures, respectively) in this case series. Esophageal TA filling was performed on the day after ESD and 1 week later and was performed again if mild stenosis was found on follow-up. EBD with TA filling was performed only for severe stenosis that prevented endoscope passage. The primary endpoint was the incidence of severe stenosis. Secondary endpoints were the total number of EBDs and additional TA filling, dysphagia score, time to stenosis and to complete re-epithelialization, and any adverse events. The incidence of severe stenosis was 4.5% (1/22; confidence interval, .1%-22.8%), and EBD was performed 2 times in 1 patient. Mild stenosis was found in 9 patients. Additional TA filling was performed in 45.5% of patients (10/22; median, 5 times; range, 1-13). The dysphagia score deteriorated to 1 to 2 in 31.8% (7/22) but showed a final score of 0 after complete re-epithelialization in 90.9% (20/22). The median time to stenosis was 3 weeks (range, 3-4) and that to complete re-epithelialization was 7 weeks (range, 4-36). No severe adverse events occurred. The esophageal TA-filling method is highly effective for preventing severe stenosis after extensive esophageal ESD. Copyright © 2018 American Society for Gastrointestinal Endoscopy. Published by Elsevier Inc. All rights reserved.

Study on aluminium-based single films.

PubMed

Vinod Kumar, G S; García-Moreno, F; Babcsán, N; Brothers, A H; Murty, B S; Banhart, J

2007-12-28

In the present paper the authors studied isolated metallic films made from the same material used for making metallic foams, and then characterised their properties. Metal films were made from a liquid aluminium alloy reinforced with ceramic particles of known concentration. Melts without such particles were also investigated. It is shown that stable films could not be made from Al-Si alloy having no particles, and just extremely thin and fragile films could be made from commercially-pure Al. In contrast, aluminium alloys containing particles such as SiC and TiB(2) allowed pulling thin, stable films, which did not rupture. Significant thinning of films was observed when the particle concentration in the melt decreased. By in situ X-ray monitoring of liquid films during pulling, film thickness and drainage effects within the liquid film could be studied. The morphology and microstructure of films was characterised after solidification. Our work shows that the question of how foams are stabilised can be studied using a simplified system such as a film, instead of having to deal with the multitude of different structural elements present in a foam.

Film Editing Handbook; Technique of 16mm Film Cutting.

ERIC Educational Resources Information Center

Churchill, Hugh B.

Designed to help the film student with the complexities of 16mm film cutting, this handbook catalogs the mechanical procedures of both picture and sound cutting and supplies step-by-step explanations of these procedures. Because the handbook was organized so that it could be used while working at the cutting bench, common cutting problems and…

Electrical applications of CVD diamond films

NASA Astrophysics Data System (ADS)

Fujimori, Naoji

Electronics applications of CVD diamond films are reported. The properties of epitaxial diamond films are affected by the orientation of the substrate and the deposition conditions. Boron-doped epitaxial films are found to have the same characteristics as natural IIb diamonds. An LED and an FET were successfully fabricated using boron-doped epitaxial films and Schottky junctions. However, these devices did not exhibit satisfactory properties. Other applications of CVD diamond films include speaker diaphragms (as both a thin-film coating and a free-standing film), and as an ideal packaging material (due to its high thermal conductivity and low dielectric constant).

Orientation filtering for crystalline films

DOEpatents

Smith, Henry I.; Atwater, Harry A.; Thompson, Carl V.; Geis, Michael W.

1986-12-30

A substrate is coated with a film to be recrystallized. A pattern of crystallization barriers is created in the film, for example, by etching voids in the film. An encapsulation layer is generally applied to protect the film, fill the voids and otherwise enhance a recrystallization process. Recrystallization is carried out such that certain orientations pass preferentially through the barrier, generally as a result of growth-velocity anisotropy. The result is a film of a specific predetermined crystallographic orientation, a range of orientations or a set of discrete orientations.

Orientation filtering for crystalline films

DOEpatents

Smith, H.I.; Atwater, H.A.; Thompson, C.V.; Geis, M.W.

1986-12-30

A substrate is coated with a film to be recrystallized. A pattern of crystallization barriers is created in the film, for example, by etching voids in the film. An encapsulation layer is generally applied to protect the film, fill the voids and otherwise enhance a recrystallization process. Recrystallization is carried out such that certain orientations pass preferentially through the barrier, generally as a result of growth-velocity anisotropy. The result is a film of a specific predetermined crystallographic orientation, a range of orientations or a set of discrete orientations. 7 figs.

Process to form mesostructured films

DOEpatents

Brinker, C. Jeffrey; Anderson, Mark T.; Ganguli, Rahul; Lu, Yunfeng

1999-01-01

This invention comprises a method to form a family of supported films film with pore size in the approximate range 0.8-20 nm exhibiting highly ordered microstructures and porosity derived from an ordered micellar or liquid-crystalline organic-inorganic precursor structure that forms during film deposition. Optically transparent, 100-500-nm thick films exhibiting a unique range of microstructures and uni-modal pore sizes are formed in seconds in a continuous coating operation. Applications of these films include sensors, membranes, low dielectric constant interlayers, anti-reflective coatings, and optical hosts.

[Spectral emissivity of thin films].

PubMed

Zhong, D

2001-02-01

In this paper, the contribution of multiple reflections in thin film to the spectral emissivity of thin films of low absorption is discussed. The expression of emissivity of thin films derived here is related to the thin film thickness d and the optical constants n(lambda) and k(lambda). It is shown that in the special case d-->infinity the emissivity of thin films is equivalent to that of the bulk material. Realistic numerical and more precise general numerical results for the dependence of the emissivity on d, n(lambda) and k(lambda) are given.

Free-standing graphene films prepared via foam film method for great capacitive flexible supercapacitors

NASA Astrophysics Data System (ADS)

Zhu, Yucan; Ye, Xingke; Tang, Zhonghua; Wan, Zhongquan; Jia, Chunyang

2017-11-01

Recently, graphene films have always attracted attention due to their excellent characteristics in energy storage. In this work, a novel graphene oxide (GO) film with excellent mechanical properties, whose thickness was regulated simply via changing the concentration of the surfactant, was successfully prepared by foam film method. After chemical reduction, the reduced GO (rGO) films have excellent electrical conductivity of ∼172 S cm-1. Moreover, the supercapacitors based on the rGO films exhibit satisfied capacitive performance of ∼56 mF cm-2 at 0.2 mA cm-2 in 6 M KOH aqueous solution. Meanwhile, the flexible all solid state supercapacitors (FSSCs) based on the rGO films also show great volumetric capacitance of ∼2810 mF cm-3 at 12 mA cm-3 (∼1607 mF cm-3 at 613 mA cm-3) with polyvinyl alcohol-KOH gel electrolyte. Besides, after 10000 cycles and continuously bent to 180° for 300 times, the volumetric capacitance of the FSSC remains at 81.4% and 90.4% of its initial capacitance value, respectively. Therefore, the free-standing rGO films prepared via foam film method could be considered as promising electrode materials for high performance flexible supercapacitors.

Olympic Training Film Profiles. Volume III.

ERIC Educational Resources Information Center

1971

Approximately 250 instructional films are described in Volume Three (1970-1971) of this review. After an introduction which considers film discussions from the instructor's point of view and offers some ideas for conducting a film showing and ordering the films, profiles of the films are presented grouped under such areas as management…

FOREIGN LANGUAGE FILMS IN LOUISIANA DEPOSITORIES.

ERIC Educational Resources Information Center

BABINEAUX, AUDREY

THIS MANUAL IS AN ANNOTATED LIST OF 16-MILLIMETER EDUCATIONAL FOREIGN LANGUAGE FILMS (BOTH LINGUISTIC AND CULTURAL) WHICH WERE PURCHASED WITH STATE AND FEDERAL FUNDS AND PLACED IN LOUISIANA'S NINE FILM LIBRARIES. FILMS ARE ARRANGED ALPHABETICALLY BY LANGUAGES. FILMS IN THE TARGET LANGUAGE ARE LISTED SEPARATELY FROM FILMS WITH ENGLISH NARRATION. A…

Nopal cactus film

NASA Astrophysics Data System (ADS)

Toxqui-López, S.; Olivares-Pérez, A.; Fuentes-Tapia, I.; Conde-Cuatzo, María. G.

2017-03-01

Nopal mucilage potentially has certain properties required for the preparation biofilms which can be used as holographic replication recording medium. In this study, mucilage from nopal was extracted and characterized by its ability to form films under different concentration with polyvinyl alcohol. The transmission holographic diffraction gratings (master) were replicated into nopal films. The results showed good diffraction efficiencies. Mucilage from nopal could represent a good option for the development of films to replication holographic, owing to; its low cost and its compatibility with the environmental.

Formation of crystalline heteroepitaxial SiC films on Si by carbonization of polyimide Langmuir-Blodgett films

NASA Astrophysics Data System (ADS)

Luchinin, Viktor V.; Goloudina, Svetlana I.; Pasyuta, Vyacheslav M.; Panov, Mikhail F.; Smirnov, Alexander N.; Kirilenko, Demid A.; Semenova, Tatyana F.; Sklizkova, Valentina P.; Gofman, Iosif V.; Svetlichnyi, Valentin M.; Kudryavtsev, Vladislav V.

2017-06-01

High-quality crystalline nano-thin SiC films on Si substrates were prepared by carbonization of polyimide (PI) Langmuir-Blodgett (LB) films. The obtained films were characterized by Fourier transform-infrared (FTIR) spectroscopy, X-ray diffraction (XRD) analysis, Raman spectroscopy, transmission electon microscopy (TEM), transmission electron diffraction (TED), and scanning electron microscopy (SEM). We demonstrated that the carbonization of a PI film on a Si substrate at 1000 °C leads to the formation of a carbon film and SiC nanocrystals on the Si substrate. It was found that five planes in the 3C-SiC(111) film are aligned with four Si(111) planes. As a result of repeated annealing of PI films containing 121 layers at 1200 °C crystalline SiC films were formed on the Si substrate. It was shown that the SiC films (35 nm) grown on Si(111) at 1200 °C have a mainly cubic 3C-SiC structure with small amount of hexagonal polytypes. Only 3C-SiC films (30 nm) were formed on the Si(100) substrate at the same temperature. It was shown that the SiC films (30-35 nm) can cover the voids with size up to 10 µm in the Si substrate. The current-voltage (I-V) characteristics of the n-Si/n-SiC heterostructure were obtained by conductive atomic force microscopy.

Discovery in Film, Book Two.

ERIC Educational Resources Information Center

Gordon, Malcolm W.

Approximately 80 16 millimeter (16mm) short films are reviewed in this introduction and guide which attempts to be comprehensive in touching the major areas and styles of 16mm films now being produced. An attempt is made to describe as carefully as possible the style and content of each film and suggest ways in which the films might be used. Films…

Effects of high temperature and film thicknesses on the texture evolution in Ag thin films

NASA Astrophysics Data System (ADS)

Eshaghi, F.; Zolanvari, A.

2017-04-01

In situ high-temperature X-ray diffraction techniques were used to study the effect of high temperatures (up to 600°C) on the texture evolution in silver thin films. Ag thin films with different thicknesses of 40, 80, 120 and 160nm were sputtered on the Si(100) substrates at room temperature. Then, microstructure of thin films was determined using X-ray diffraction. To investigate the influence of temperature on the texture development in the Ag thin films with different thicknesses, (111), (200) and (220) pole figures were evaluated and orientation distribution functions were calculated. Minimizing the total energy of the system which is affected by competition between surface and elastic strain energy was a key factor in the as-deposited and post annealed thin films. Since sputtering depositions was performed at room temperature and at the same thermodynamic conditions, the competition growth caused the formation of the {122} < uvw \\rangle weak fiber texture in as-deposited Ag thin films. It was significantly observed that the post annealed Ag thin films showed {111} < uvw \\rangle orientations as their preferred orientations, but their preferred fiber texture varied with the thickness of thin films. Increasing thin film thickness from 40nm to 160nm led to decreasing the intensity of the {111} < uvw \\rangle fiber texture.

Health Careers Film Guide.

ERIC Educational Resources Information Center

National Institutes of Health (DHEW), Bethesda, MD. Bureau of Health Manpower Education.

This document, which represents a survey of the entire health career film field, was designed to provide information for people interested in a health career. The guide indicates that a major criteria for film selection was recency; however, some older films that give a fairly accurate image of a profession were included, with some emphasis given…

99 Films on Drugs.

ERIC Educational Resources Information Center

Weber, David O., Ed.

This catalog describes and evaluates 16-millimeter films about various aspects of drug use. Among the subjects covered by the 99 films are the composition and effects of different drugs, reasons why people use drugs, life in the drug culture, the problem of law enforcement, and various means of dealing with drug users. Each film is synopsized. Two…

Dosimetric characterization of GafChromic EBT film and its implication on film dosimetry quality assurance.

PubMed

Fuss, Martina; Sturtewagen, Eva; De Wagter, Carlos; Georg, Dietmar

2007-07-21

The suitability of radiochromic EBT film was studied for high-precision clinical quality assurance (QA) by identifying the dose response for a wide range of irradiation parameters typically modified in highly-conformal treatment techniques. In addition, uncertainties associated with varying irradiation conditions were determined. EBT can be used for dose assessment of absorbed dose levels as well as relative dosimetry when compared to absolute absorbed dose calibrated using ionization chamber results. For comparison, a silver halide film (Kodak EDR-2) representing the current standard in film dosimetry was included. As an initial step a measurement protocol yielding accurate and precise results was established for a flatbed transparency scanner (Epson Expression 1680 Pro) that was utilized as a film reading instrument. The light transmission measured by the scanner was found to depend on the position of the film on the scanner plate. For three film pieces irradiated with doses of 0 Gy, approximately 1 Gy and approximately 7 Gy, the pixel values measured in portrait or landscape mode differed by 4.7%, 6.2% and 10.0%, respectively. A study of 200 film pieces revealed an excellent sheet-to-sheet uniformity. On a long time scale, the optical development of irradiated EBT film consisted of a slow but steady increase of absorbance which was not observed to cease during 4 months. Sensitometric curves of EBT films obtained under reference conditions (SSD = 95 cm, FS = 5 x 5 cm(2), d = 5 cm) for 6, 10 and 25 MV photon beams did not show any energy dependence. The average separation between all curves was only 0.7%. The variation of the depth d (range 2-25 cm) in the phantom did not affect the dose response of EBT film. Also the influence of the radiation field size (range 3 x 3-40 x 40 cm(2)) on the sensitometric curve was not significant. For EDR-2 films maximum differences between the calibration curves reached 7-8% for X6MV and X25MV. Radiochromic EBT film, in

Dosimetric characterization of GafChromic EBT film and its implication on film dosimetry quality assurance

NASA Astrophysics Data System (ADS)

Fuss, Martina; Sturtewagen, Eva; DeWagter, Carlos; Georg, Dietmar

2007-07-01

The suitability of radiochromic EBT film was studied for high-precision clinical quality assurance (QA) by identifying the dose response for a wide range of irradiation parameters typically modified in highly-conformal treatment techniques. In addition, uncertainties associated with varying irradiation conditions were determined. EBT can be used for dose assessment of absorbed dose levels as well as relative dosimetry when compared to absolute absorbed dose calibrated using ionization chamber results. For comparison, a silver halide film (Kodak EDR-2) representing the current standard in film dosimetry was included. As an initial step a measurement protocol yielding accurate and precise results was established for a flatbed transparency scanner (Epson Expression 1680 Pro) that was utilized as a film reading instrument. The light transmission measured by the scanner was found to depend on the position of the film on the scanner plate. For three film pieces irradiated with doses of 0 Gy, ~1 Gy and ~7 Gy, the pixel values measured in portrait or landscape mode differed by 4.7%, 6.2% and 10.0%, respectively. A study of 200 film pieces revealed an excellent sheet-to-sheet uniformity. On a long time scale, the optical development of irradiated EBT film consisted of a slow but steady increase of absorbance which was not observed to cease during 4 months. Sensitometric curves of EBT films obtained under reference conditions (SSD = 95 cm, FS = 5 × 5 cm2, d = 5 cm) for 6, 10 and 25 MV photon beams did not show any energy dependence. The average separation between all curves was only 0.7%. The variation of the depth d (range 2-25 cm) in the phantom did not affect the dose response of EBT film. Also the influence of the radiation field size (range 3 × 3-40 × 40 cm2) on the sensitometric curve was not significant. For EDR-2 films maximum differences between the calibration curves reached 7-8% for X6MV and X25MV. Radiochromic EBT film, in combination with a flatbed scanner

Predicting film dose to aid in cassette placement for radiation therapy portal verification film images.

PubMed

Keys, Richard A; Marks, James E; Haus, Arthur G

2002-12-01

EC film has improved portal localization images with better contrast and improved distinction of bony structures and air-tissue interfaces. A cassette with slower speed screens was used with EC film to image the treatment portal during the entire course of treatment (verification) instead of taking separate films after treatment. Measurements of film density vs source to film distance (SFD) were made using 15 and 25 cm thick water phantoms with both 6 and 18 MV photons from I to 40 cm past the phantom. A characteristic (H & D) curve was measured in air to compare dose to film density. Results show the reduction in radiation between patient and cassette more closely follows an "inverse cube law" rather than an inverse square law. Formulas to calculate radiation exposure to the film, and the desired SFD were based on patient tumor dose, calculation of the exit dose, and the inverse cube relationship. A table of exposure techniques based on the SFD for a given tumor dose was evaluated and compared to conventional techniques. Although the film has a high contrast, there is enough latitude that excellent films can be achieved using a fixed SFD based simply on the tumor dose and beam energy. Patient diameter has a smaller effect. The benefits of imaging portal films during the entire treatment are more reliability in the accuracy of the portal image, ability to detect patient motion, and reduction in the time it takes to take portal images.

Morphological Influence of Solution-Processed Zinc Oxide Films on Electrical Characteristics of Thin-Film Transistors

PubMed Central

Lee, Hyeonju; Zhang, Xue; Hwang, Jaeeun; Park, Jaehoon

2016-01-01

We report on the morphological influence of solution-processed zinc oxide (ZnO) semiconductor films on the electrical characteristics of ZnO thin-film transistors (TFTs). Different film morphologies were produced by controlling the spin-coating condition of a precursor solution, and the ZnO films were analyzed using atomic force microscopy, X-ray diffraction, X-ray photoemission spectroscopy, and Hall measurement. It is shown that ZnO TFTs have a superior performance in terms of the threshold voltage and field-effect mobility, when ZnO crystallites are more densely packed in the film. This is attributed to lower electrical resistivity and higher Hall mobility in a densely packed ZnO film. In the results of consecutive TFT operations, a positive shift in the threshold voltage occurred irrespective of the film morphology, but the morphological influence on the variation in the field-effect mobility was evident. The field-effect mobility in TFTs having a densely packed ZnO film increased continuously during consecutive TFT operations, which is in contrast to the mobility decrease observed in the less packed case. An analysis of the field-effect conductivities ascribes these results to the difference in energetic traps, which originate from structural defects in the ZnO films. Consequently, the morphological influence of solution-processed ZnO films on the TFT performance can be understood through the packing property of ZnO crystallites. PMID:28773973

Optimum processing of mammographic film.

PubMed

Sprawls, P; Kitts, E L

1996-03-01

Underprocessing of mammographic film can result in reduced contrast and visibility of breast structures and an unnecessary increase in radiation dose to the patient. Underprocessing can be caused by physical factors (low developer temperature, inadequate development time, insufficient developer agitation) or chemical factors (developer not optimized for film type; overdiluted, underreplenished, contaminated, or frequently changed developer). Conventional quality control programs are designed to produce consistent processing but do not address the issue of optimum processing. Optimum processing is defined as the level of processing that produces the film performance characteristics (contrast and sensitivity) specified by the film manufacturer. Optimum processing of mammographic film can be achieved by following a two-step protocol. The first step is to set up the processing conditions according to recommendations from the film and developer chemistry manufacturers. The second step is to verify the processing results by comparing them with sensitometric data provided by the film manufacturer.

Minimum film thickness in elliptical contacts for different regimes of fluid-film lubrication

NASA Technical Reports Server (NTRS)

Hamrock, B. J.; Dowson, D.

1978-01-01

The film-parameter equations are provided for four fluid-film lubrication regimes found in elliptical contacts. These regimes are isoviscous-rigid; viscous-rigid; elastohydrodynamic of low-elastic-modulus materials, or isoviscous-elastic; and elastohydrodynamic, or viscous-elastic. The influence or lack of influence of elastic and viscous effects is the factor that distinguishes these regimes. The film-parameter equations for the respective regimes come from earlier theoretical studies by the authors on elastohydrodynamic and hydrodynamic lubrication of elliptical conjunctions. These equations are restated and the results are presented as a map of the lubrication regimes, with film-thickness contours on a log-log grid of the viscosity and elasticity parameters for five values of the ellipticity parameter. The results present a complete theoretical film-parameter solution for elliptical contacts in the four lubrication regimes.

Improved liquid-film electron stripper

DOEpatents

Gavin, B.F.

1984-11-01

An improved liquid-film electron stripper particularly for high intensity heavy ion beams which produces constant regenerated, stable, free-standing liquid films having an adjustable thickness between 0.3 to 0.05 microns. The improved electron stripper is basically composed of at least one high speed, rotating disc with a very sharp, precision-like, ground edge on one side of the disc's periphery and with highly polished, flat, radial surface adjacent the sharp edge. A fine stream of liquid, such as oil, impinges at a 90/sup 0/ angle adjacent the disc's sharp outer edge. Film terminators, located at a selected distance from the disc perimeter are positioned approximately perpendicular to the film. The terminators support, shape, and stretch the film and are arranged to assist in the prevention of liquid droplet formation by directing the collected film to a reservoir below without breaking or interfering with the film. One embodiment utilizes two rotating discs and associated terminators, with the discs rotating so as to form films in opposite directions, and with the second disc being located down beam-line relative to the first disc.

Effects of Loading Frequency and Film Thickness on the Mechanical Behavior of Nanoscale TiN Film

NASA Astrophysics Data System (ADS)

Liu, Jin-na; Xu, Bin-shi; Wang, Hai-dou; Cui, Xiu-fang; Jin, Guo; Xing, Zhi-guo

2017-09-01

The mechanical properties of a nanoscale-thickness film material determine its reliability and service life. To achieve quantitative detection of film material mechanical performance based on nanoscale mechanical testing methods and to explore the influence of loading frequency of the cycle load on the fatigue test, a TiN film was prepared on monocrystalline silicon by magnetron sputtering. The microstructure of the nanoscale-thickness film material was characterized by using scanning electron microscopy and high-resolution transmission electron microscopy. The residual stress distribution of the thin film was obtained by using an electronic film stress tester. The hardness values and the fatigue behavior were measured by using a nanomechanical tester. Combined with finite element simulation, the paper analyzed the influence of the film thickness and loading frequency on the deformation, as well as the equivalent stress and strain. The results showed that the TiN film was a typical face-centered cubic structure with a large amount of amorphous. The residual compressive stress decreased gradually with increasing thin film thickness, and the influence of the substrate on the elastic modulus and hardness was also reduced. A greater load frequency would accelerate the dynamic fatigue damage that occurs in TiN films.

The Wim Van Leer Competition for Young Film Makers at the Jerusalem Film Festival.

ERIC Educational Resources Information Center

Mendel, Gilli

1999-01-01

Describes the Jerusalem Film Center and the background, history, and organization of the Wim Van Leer Competition which was established for young filmmakers in high school. Describes the Jerusalem Film Festival, film studies programs at Israeli high schools, and future possibilities. (Author/LRW)

Chemical-Vapor-Deposited Diamond Film

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa

1999-01-01

This chapter describes the nature of clean and contaminated diamond surfaces, Chemical-vapor-deposited (CVD) diamond film deposition technology, analytical techniques and the results of research on CVD diamond films, and the general properties of CVD diamond films. Further, it describes the friction and wear properties of CVD diamond films in the atmosphere, in a controlled nitrogen environment, and in an ultra-high-vacuum environment.

Reference dosimetry using radiochromic film

PubMed Central

Girard, Frédéric; Bouchard, Hugo

2012-01-01

The objectives of this study are to identify and quantify factors that influence radiochromic film dose response and to determine whether such films are suitable for reference dosimetry. The influence of several parameters that may introduce systematic dose errors when performing reference dose measurements were investigated. The effect of the film storage temperature was determined by comparing the performance of three lots of GAFCHROMIC EBT2 films stored at either 4°C or room temperature. The effect of high (>80%) or low (<20%) relative humidity was also determined. Doses measured in optimal conditions with EBT and EBT2 films were then compared with an A12 ionization chamber measurement. Intensity‐modulated radiation therapy quality controls using EBT2 films were also performed in reference dose. The results obtained using reference dose measurements were compared with those obtained using relative dose measurements. Storing the film at 4°C improves the stability of the film over time, but does not eliminate the noncatalytic film development, seen as a rise in optical density over time in the absence of radiation. Relative humidity variations ranging from 80% to 20% have a strong impact on the optical density and could introduce dose errors of up to 15% if the humidity were not controlled during the film storage period. During the scanning procedure, the film temperature influences the optical density that is measured. When controlling for these three parameters, the dose differences between EBT or EBT2 and the A12 chamber are found to be within ±4% (2σ level) over a dose range of 20–350 cGy. Our results also demonstrate the limitation of the Anisotropic Analytical Algorithm for dose calculation of highly modulated treatment plans. PACS numbers: 87.55.Qr; 87.56.Fc PMID:23149793

Reduced temperature-dependent thermal conductivity of magnetite thin films by controlling film thickness

PubMed Central

2014-01-01

We report on the out-of-plane thermal conductivities of epitaxial Fe3O4 thin films with thicknesses of 100, 300, and 400 nm, prepared using pulsed laser deposition (PLD) on SiO2/Si substrates. The four-point probe three-omega (3-ω) method was used for thermal conductivity measurements of the Fe3O4 thin films in the temperature range of 20 to 300 K. By measuring the temperature-dependent thermal characteristics of the Fe3O4 thin films, we realized that their thermal conductivities significantly decreased with decreasing grain size and thickness of the films. The out-of-plane thermal conductivities of the Fe3O4 films were found to be in the range of 0.52 to 3.51 W/m · K at 300 K. For 100-nm film, we found that the thermal conductivity was as low as approximately 0.52 W/m · K, which was 1.7 to 11.5 order of magnitude lower than the thermal conductivity of bulk material at 300 K. Furthermore, we calculated the temperature dependence of the thermal conductivity of these Fe3O4 films using a simple theoretical Callaway model for comparison with the experimental data. We found that the Callaway model predictions agree reasonably with the experimental data. We then noticed that the thin film-based oxide materials could be efficient thermoelectric materials to achieve high performance in thermoelectric devices. PMID:24571956

Gravity Effects in Condensing and Evaporating Films

NASA Technical Reports Server (NTRS)

Hermanson, J. C.; Som, S. M.; Allen, J. S.; Pedersen, P. C.

2004-01-01

A general overview of gravity effects in condensing and evaporating films is presented. The topics include: 1) Research Overview; 2) NASA Recognizes Critical Need for Condensation & Evaporation Research to Enable Human Exploration of Space; 3) Condensation and Evaporation Research in Reduced Gravity is Enabling for AHST Technology Needs; 4) Differing Role of Surface Tension on Condensing/Evaporating Film Stability; 5) Fluid Mechanisms in Condensing and Evaporating Films in Reduced Gravity; 6) Research Plan; 7) Experimental Configurations for Condensing Films; 8) Laboratory Condensation Test Cell; 9) Aircraft Experiment; 10) Condensation Study Current Test Conditions; 11) Diagnostics; 12) Shadowgraph Images of Condensing n- pentane Film in Unstable (-1g) Configuration; 13) Condensing n-Pentane Film in Normal Gravity (-1g) at Constant Pressure; 14) Condensing n-Pentane Film in Normal Gravity (-1g) with Cyclic Pressure; 15) Non-condensing Pumped Film in Normal Gravity (-1g); 16) Heat Transfer Coefficient in Developing, Unstable Condensing Film in Normal Gravity; 17) Heat Transfer for Unsteady Condensing Film (-1g); 18) Ultrasound Measurement of Film Thickness N-pentane Film, Stable (+1g) Configuration; and 19) Ultrasound Measurement of Film Thickness N-pentane Film, Unstable (-1g) Configuration.

Preparation of Gelatin Layer Film with Gold Clusters in Using Photographic Film

NASA Astrophysics Data System (ADS)

Kuge, Ken'ichi; Arisawa, Michiko; Aoki, Naokazu; Hasegawa, Akira

2000-12-01

A gelatin layer film with gold clusters is produced by taking advantage of the photosensitivity of silver halide photography. Through exposure silver specks, which are called latent-image specks and are composed of several reduced silver atoms, are formed on the surface of silver halide grains in the photographic film. As the latent-image specks act as a catalyst for redox reaction, reduced gold atoms are deposited on the latent-image specks when the exposed film is immersed in a gold (I) thiocyanate complex solution for 5-20 days. Subsequently, when the silver halide grains are dissolved and removed, the gelatin layer film with gold clusters remains. The film produced by this method is purple and showed an absorption spectrum having a maximum of approximately 560 nm as a result of plasmon absorption. The clusters continued to grow with immersion time, and the growth rate increased as the concentration of the gold complex solution was increased. The cluster diameter changed from 20 nm to 100 nm. By this method, it is possible to produce a gelatin film of a large area with evenly dispersed gold clusters, and since it is produced only on the exposed area, pattern forming is also possible.

Fracture characteristics of balloon films

NASA Technical Reports Server (NTRS)

Portanova, Marc A.

1989-01-01

An attempt was made to determine the failure modes of high altitude scientific balloons through an investigation of the fracture characteristics of the thin polyethylene films. Two films were the subject of the evaluation, Winzen Int.'s Stratafilm SF-85 and Raven Industries' Astro-E. Research began with an investigation of the film's cold brittleness point and it's effect on the ultimate strength and elasticity of the polyethylene film. A series of preliminary investigations were conducted to develop an understanding of the material characteristics. The primary focus of this investigation was on the notch sensitivity of the films. Simple stress strain tests were also conducted to enable analysis employing fracture toughness parameters. Studies were conducted on both film types at 23 C (room temperature), -60 C, -90 C, and -120 C.

Creating an evidence-based dentistry culture at Baylor College of Dentistry: the winds of change.

PubMed

Hinton, Robert J; Dechow, Paul C; Abdellatif, Hoda; Jones, Daniel L; McCann, Ann L; Schneiderman, Emet D; D'Souza, Rena

2011-03-01

In the early years of the new millennium, the National Institute of Dental and Craniofacial Research of the National Institutes of Health began funding Oral Health Research Education Grants using the R25 mechanism to promote the application of basic and clinical research findings to clinical training and to encourage students to pursue careers in oral health research. This report describes the impact of an R25 grant awarded to the Texas A&M Health Science Center's Baylor College of Dentistry (BCD) on its curriculum and faculty development efforts. At BCD, the R25 grant supports a multipronged initiative that employs clinical research as a vehicle for acquainting both students and faculty with the tools of evidence-based dentistry (EBD). New coursework and experiences in all four years of the curriculum plus a variety of faculty development offerings are being used to achieve this goal. Progress on these fronts is reflected in a nascent EBD culture characterized by increasing participation and buy-in by students and faculty. The production of a new generation of dental graduates equipped with the EBD skill set as well as a growing nucleus of faculty members who can model the importance of evidence-based practice is of paramount importance for the future of dentistry.

Creating an Evidence-Based Dentistry Culture at Baylor College of Dentistry: The Winds of Change

PubMed Central

Hinton, Robert J.; Dechow, Paul C.; Abdellatif, Hoda; Jones, Daniel L.; McCann, Ann L.; Schneiderman, Emet D.; D’Souza, Rena

2011-01-01

In the early years of the new millennium, the National Institute of Dental and Craniofacial Research of the National Institutes of Health began funding Oral Health Research Education Grants using the R25 mechanism to promote the application of basic and clinical research findings to clinical training and to encourage students to pursue careers in oral health research. This report describes the impact of an R25 grant awarded to the Texas A&M Health Science Center’s Baylor College of Dentistry (BCD) on its curriculum and faculty development efforts. At BCD, the R25 grant supports a multipronged initiative that employs clinical research as a vehicle for acquainting both students and faculty with the tools of evidence-based dentistry (EBD). New coursework and experiences in all four years of the curriculum plus a variety of faculty development offerings are being used to achieve this goal. Progress on these fronts is reflected in a nascent EBD culture characterized by increasing participation and buy-in by students and faculty. The production of a new generation of dental graduates equipped with the EBD skill set as well as a growing nucleus of faculty members who can model the importance of evidence-based practice is of paramount importance for the future of dentistry. PMID:21368252

Endoscopic management of Crohn’s strictures

PubMed Central

Bessissow, Talat; Reinglas, Jason; Aruljothy, Achuthan; Lakatos, Peter L; Van Assche, Gert

2018-01-01

Symptomatic intestinal strictures develop in more than one third of patients with Crohn’s disease (CD) within 10 years of disease onset. Strictures can be inflammatory, fibrotic or mixed and result in a significant decline in quality of life, frequently requiring surgery for palliation of symptoms. Patients under the age of 40 with perianal disease are more likely to suffer from disabling ileocolonic disease thus may have a greater risk for fibrostenotic strictures. Treatment options for fibrostenotic strictures are limited to endoscopic and surgical therapy. Endoscopic balloon dilatation (EBD) appears to be a safe, less invasive and effective alternative modality to replace or defer surgery. Serious complications are rare and occur in less than 3% of procedures. For non-complex strictures without adjacent fistulizaation or perforation that are less than 5 cm in length, EBD should be considered as first-line therapy. The aim of this review is to present the current literature on the endoscopic management of small bowel and colonic strictures in CD, which includes balloon dilatation, adjuvant techniques of intralesional injection of steroids and anti-tumor necrosis factor, and metal stent insertion. Short and long-term outcomes, complications and safety of EBD will be discussed. PMID:29740201

An approach to define semantics for BPM systems interoperability

NASA Astrophysics Data System (ADS)

Rico, Mariela; Caliusco, María Laura; Chiotti, Omar; Rosa Galli, María

2015-04-01

This article proposes defining semantics for Business Process Management systems interoperability through the ontology of Electronic Business Documents (EBD) used to interchange the information required to perform cross-organizational processes. The semantic model generated allows aligning enterprise's business processes to support cross-organizational processes by matching the business ontology of each business partner with the EBD ontology. The result is a flexible software architecture that allows dynamically defining cross-organizational business processes by reusing the EBD ontology. For developing the semantic model, a method is presented, which is based on a strategy for discovering entity features whose interpretation depends on the context, and representing them for enriching the ontology. The proposed method complements ontology learning techniques that can not infer semantic features not represented in data sources. In order to improve the representation of these entity features, the method proposes using widely accepted ontologies, for representing time entities and relations, physical quantities, measurement units, official country names, and currencies and funds, among others. When the ontologies reuse is not possible, the method proposes identifying whether that feature is simple or complex, and defines a strategy to be followed. An empirical validation of the approach has been performed through a case study.

Making the Case for Practice-Based Research and the Imperative Role of Design Practitioners.

PubMed

Freihoefer, Kara; Zborowsky, Terri

2017-04-01

The purpose of this article is to justify the need for evidence-based design (EBD) in a research-based architecture and design practice. This article examines the current state of practice-based research (PBR), supports the need for EBD, illustrates PBR methods that can be applied to design work, and explores how findings can be used as a decision-making tool during design and as a validation tool during postoccupancy. As a result, design professions' body of knowledge will advance and practitioners will be better informed to protect the health, safety, and welfare of the society. Furthermore, characteristics of Friedman's progressive research program are used as a framework to examine the current state of PBR in design practice. A modified EBD approach is proposed and showcased with a case study of a renovated inpatient unit. The modified approach demonstrates how a highly integrated project team, especially the role of design practitioners, contributed to the success of utilizing baseline findings and evidence in decision-making throughout the design process. Lastly, recommendations and resources for learning research concepts are provided for practitioners. It is the role of practitioners to pave the way for the next generation of design professionals, as the request and expectation for research become more prevalent in design practice.

You Can See Film through Digital: A Report from Where the Archiving of Motion Picture Film Stands

NASA Astrophysics Data System (ADS)

Tochigi, Akira

In recent years, digital technology has brought drastic change to the archiving of motion picture film. By collecting digital media as well as film, many conventional film archives have transformed themselves into moving image archives or audiovisual archives. As well, digital technology has expanded the possibility of the restoration of motion picture film in comparison with conventional photochemical (analog) restoration. This paper first redefines some fundamental terms regarding the archiving of motion picture film and discusses the conditions which need consideration for film archiving in Japan. With a few examples of the recent restoration projects conducted by National Film Center of the National Museum of Modern Art, Tokyo, this paper then clarifies new challenges inherent in digital restoration and urges the importance of better appreciation of motion picture film.

NMR characterization of thin films

DOEpatents

Gerald II, Rex E.; Klingler, Robert J.; Rathke, Jerome W.; Diaz, Rocio; Vukovic, Lela

2010-06-15

A method, apparatus, and system for characterizing thin film materials. The method, apparatus, and system includes a container for receiving a starting material, applying a gravitational force, a magnetic force, and an electric force or combinations thereof to at least the starting material, forming a thin film material, sensing an NMR signal from the thin film material and analyzing the NMR signal to characterize the thin film of material.

NMR characterization of thin films

DOEpatents

Gerald, II, Rex E.; Klingler, Robert J.; Rathke, Jerome W.; Diaz, Rocio; Vukovic, Lela

2008-11-25

A method, apparatus, and system for characterizing thin film materials. The method, apparatus, and system includes a container for receiving a starting material, applying a gravitational force, a magnetic force, and an electric force or combinations thereof to at least the starting material, forming a thin film material, sensing an NMR signal from the thin film material and analyzing the NMR signal to characterize the thin film of material.

Very high resolution aerial films

NASA Astrophysics Data System (ADS)

Becker, Rolf

1986-11-01

The use of very high resolution aerial films in aerial photography is evaluated. Commonly used panchromatic, color, and CIR films and their high resolution equivalents are compared. Based on practical experience and systematic investigations, the very high image quality and improved height accuracy that can be achieved using these films are demonstrated. Advantages to be gained from this improvement and operational restrictions encountered when using high resolution film are discussed.

Surface Modification of Solution-Processed ZrO2 Films through Double Coating for Pentacene Thin-Film Transistors

NASA Astrophysics Data System (ADS)

Kwon, Jin-Hyuk; Bae, Jin-Hyuk; Lee, Hyeonju; Park, Jaehoon

2018-03-01

We report the modification of surface properties of solution-processed zirconium oxide (ZrO2) dielectric films achieved by using double-coating process. It is proven that the surface properties of the ZrO2 film are modified through the double-coating process; the surface roughness decreases and the surface energy increases. The present surface modification of the ZrO2 film contributes to an increase in grain size of the pentacene film, thereby increasing the field-effect mobility and decreasing the threshold voltage of the pentacene thin-film transistors (TFTs) having the ZrO2 gate dielectric. Herein, the molecular orientation of pentacene film is also studied based on the results of contact angle and X-ray diffraction measurements. Pentacene molecules on the double-coated ZrO2 film are found to be more tilted than those on the single-coated ZrO2 film, which is attributed to the surface modification of the ZrO2 film. However, no significant differences are observed in insulating properties between the single-and the double-coated ZrO2 dielectric films. Consequently, the characteristic improvements of the pentacene TFTs with the double-coated ZrO2 gate dielectric film can be understood through the increase in pentacene grain size and the reduction in grain boundary density.

Infrared radiation of thin plastic films.

NASA Technical Reports Server (NTRS)

Tien, C. L.; Chan, C. K.; Cunnington, G. R.

1972-01-01

A combined analytical and experimental study is presented for infrared radiation characteristics of thin plastic films with and without a metal substrate. On the basis of the thin-film analysis, a simple analytical technique is developed for determining band-averaged optical constants of thin plastic films from spectral normal transmittance data for two different film thicknesses. Specifically, the band-averaged optical constants of polyethylene terephthalate and polyimide were obtained from transmittance measurements of films with thicknesses in the range of 0.25 to 3 mil. The spectral normal reflectance and total normal emittance of the film side of singly aluminized films are calculated by use of optical constants; the results compare favorably with measured values.

Thin film cell development workshop report

NASA Technical Reports Server (NTRS)

Woodyard, James R.

1991-01-01

The Thin Film Development Workshop provided an opportunity for those interested in space applications of thin film cells to debate several topics. The unique characteristics of thin film cells as well as a number of other issues were covered during the discussions. The potential of thin film cells, key research and development issues, manufacturing issues, radiation damage, substrates, and space qualification of thin film cells were discussed.

The Possibility of Film Criticism.

ERIC Educational Resources Information Center

Poague, Leland; Cadbury, William

1989-01-01

Examines the role of critical language in film criticism. Compares and contrasts Monroe Beardsley's philosophy on film aesthetics with the New Criticism. Outlines some of the contributions Beardsley has made to the study of film criticism. (KM)

Disability in Full-Length Feature Films: Frequency and Quality of Films over an 11 Year Span.

ERIC Educational Resources Information Center

Byrd, E. Keith; Elliot, Timothy R.

1988-01-01

This study assessed the presentation of disabling conditions in feature films and the general quality of these films (as judged by professional film critics' reviews and movie-goer ratings). Psychiatric disorder was the disability most frequently depicted. Films varied in quality with critics markedly more negative in their reviews than movie…

Protective overcoating of films

NASA Technical Reports Server (NTRS)

Maas, K. A.

1972-01-01

Kodak Film Type SO-212 was emulsion overcoated with gelatin and lacquer to evaluate the feasibility of application of the coatings, any image degradation, and the relative protection offered against abrasion. Evaluated were: Eastman motion picture film lacquer Type 485, water solutions of Eastman purified Calfskin gelatin, and experimental Eastman gelatin stripping film of 4 and 6 microns. Conclusions reached were: (1) All coatings can be applied with relative ease with the only limitation being that of equipment. (2) None of the coatings degrade the processed image. (3) All of the coatings provide protection to the emulsion. These conclusions apply to any film which may be considered for overcoating.

Application of a tablet film coating model to define a process-imposed transition boundary for robust film coating.

PubMed

van den Ban, Sander; Pitt, Kendal G; Whiteman, Marshall

2018-02-01

A scientific understanding of interaction of product, film coat, film coating process, and equipment is important to enable design and operation of industrial scale pharmaceutical film coating processes that are robust and provide the level of control required to consistently deliver quality film coated product. Thermodynamic film coating conditions provided in the tablet film coating process impact film coat formation and subsequent product quality. A thermodynamic film coating model was used to evaluate film coating process performance over a wide range of film coating equipment from pilot to industrial scale (2.5-400 kg). An approximate process-imposed transition boundary, from operating in a dry to a wet environment, was derived, for relative humidity and exhaust temperature, and used to understand the impact of the film coating process on product formulation and process control requirements. This approximate transition boundary may aid in an enhanced understanding of risk to product quality, application of modern Quality by Design (QbD) based product development, technology transfer and scale-up, and support the science-based justification of critical process parameters (CPPs).

Electrical initiation of an energetic nanolaminate film

DOEpatents

Tringe, Joseph W.; Gash, Alexander E.; Barbee, Jr., Troy W.

2010-03-30

A heating apparatus comprising an energetic nanolaminate film that produces heat when initiated, a power source that provides an electric current, and a control that initiates the energetic nanolaminate film by directing the electric current to the energetic nanolaminate film and joule heating the energetic nanolaminate film to an initiation temperature. Also a method of heating comprising providing an energetic nanolaminate film that produces heat when initiated, and initiating the energetic nanolaminate film by directing an electric current to the energetic nanolaminate film and joule heating the energetic nanolaminate film to an initiation temperature.

The Thin Oil Film Equation

NASA Technical Reports Server (NTRS)

Brown, James L.; Naughton, Jonathan W.

1999-01-01

A thin film of oil on a surface responds primarily to the wall shear stress generated on that surface by a three-dimensional flow. The oil film is also subject to wall pressure gradients, surface tension effects and gravity. The partial differential equation governing the oil film flow is shown to be related to Burgers' equation. Analytical and numerical methods for solving the thin oil film equation are presented. A direct numerical solver is developed where the wall shear stress variation on the surface is known and which solves for the oil film thickness spatial and time variation on the surface. An inverse numerical solver is also developed where the oil film thickness spatial variation over the surface at two discrete times is known and which solves for the wall shear stress variation over the test surface. A One-Time-Level inverse solver is also demonstrated. The inverse numerical solver provides a mathematically rigorous basis for an improved form of a wall shear stress instrument suitable for application to complex three-dimensional flows. To demonstrate the complexity of flows for which these oil film methods are now suitable, extensive examination is accomplished for these analytical and numerical methods as applied to a thin oil film in the vicinity of a three-dimensional saddle of separation.

Introduction to Film Making.

ERIC Educational Resources Information Center

Davis, Robert E.

This booklet is intended for teachers who are now teaching units in film production as part of a program in communication or who wish to begin work with filmmaking in such a program. The first section is intended to serve as a brief introduction to film theory, while a major portion of the rest of the booklet is devoted to film projects which may…

Renaissance of the Film.

ERIC Educational Resources Information Center

Bellone, Julius, Ed.

The post-World War II period was one of the liveliest in the history of the cinema. This is a collection of 33 critical articles on some of the best films of the perd. Most of the essays explicate the themes and symbols of the films. The essays deal with these films: "The Apu Trilogy,""L'Avventura,""Balthazar,""Blow-Up,""Bonnie and Clyde," Citizen…

Thin-film rechargeable lithium batteries

NASA Astrophysics Data System (ADS)

Dudney, N. J.; Bates, J. B.; Lubben, D.

1994-11-01

Small thin-film rechargeable cells have been fabricated with a lithium phosphorus oxynitride electrolyte, Li metal anode, and Li(1-x)Mn2O4 as the cathode film. The cathode films were fabricated by several different techniques resulting in both crystalline and amorphous films. These were compared by observing the cell discharge behavior. Estimates have been made for the scale-up of such a thin-film battery to meet the specifications for the electric vehicle application. The specific energy, energy density, and cycle life are expected to meet the USABC mid-term criteria. However, the areas of the thin-films needed to fabricate such a cell are very large. The required areas could be greatly reduced by operating the battery at temperatures near 100 C or by enhancing the lithium ion transport rate in the cathode material.

The Environment Film Review. A Critical Guide to Ecology Films.

ERIC Educational Resources Information Center

Environment Information Center, New York, NY.

Critical reviews of more than 600 environmental films selected from a field of several thousand are contained in this reference guide. Designed to provide a comprehensive selection of films covering all aspects of environmental affairs, from air pollution to wildlife, the guide is primarily user-oriented. It consists of two parts: a Review…

Current Film Periodicals in English. Revised Edition.

ERIC Educational Resources Information Center

Reilly, Adam, Comp.

This bibliography of about 200 periodicals dealing with film covers several types of magazine: scholarly journals on film aesthetics, like "The Film Journal"; news notes for movie fans, like "Film Nut News"; magazines which cover films as well as the other arts, like "Cue" and "After Dark"; film education periodicals, like "Media and Methods";…

Skylab program payload integration. Skylab film environmental effects

NASA Technical Reports Server (NTRS)

1975-01-01

The effects of the Skylab environments on the 22 types of film used for data recording on Skylab were evaluated. Environmental histories and sensitometric curves for 114 rolls of film used for this evaluation are presented. Photographic parameters evaluated in detail were film fogging of black and white films, changes in maximum density of color film, latent image fading, and changes in film sensitivity. Other photographic and film physical anomalies such as electrostatic exposure, emulsion cracking, and reciprocity failure were also documented. Results based upon comparison of film sensitometric data for flight film with ground control film and ground test film are presented independently for each film type. The study showed that photographic film fulfilled the requirements of the Skylab applications in which it was used. Environmental film degradation, although present on almost every roll, did not preclude recording sufficient data to meet experiment requirements for all film, except film type SC-5. Specific conclusions are provided in the areas of further analyses, tests, and developments.

Epitaxial thin films

DOEpatents

Hunt, Andrew Tye; Deshpande, Girish; Lin, Wen-Yi; Jan, Tzyy-Jiuan

2006-04-25

Epitatial thin films for use as buffer layers for high temperature superconductors, electrolytes in solid oxide fuel cells (SOFC), gas separation membranes or dielectric material in electronic devices, are disclosed. By using CCVD, CACVD or any other suitable deposition process, epitaxial films having pore-free, ideal grain boundaries, and dense structure can be formed. Several different types of materials are disclosed for use as buffer layers in high temperature superconductors. In addition, the use of epitaxial thin films for electrolytes and electrode formation in SOFCs results in densification for pore-free and ideal gain boundary/interface microstructure. Gas separation membranes for the production of oxygen and hydrogen are also disclosed. These semipermeable membranes are formed by high-quality, dense, gas-tight, pinhole free sub-micro scale layers of mixed-conducting oxides on porous ceramic substrates. Epitaxial thin films as dielectric material in capacitors are also taught herein. Capacitors are utilized according to their capacitance values which are dependent on their physical structure and dielectric permittivity. The epitaxial thin films of the current invention form low-loss dielectric layers with extremely high permittivity. This high permittivity allows for the formation of capacitors that can have their capacitance adjusted by applying a DC bias between their electrodes.

Jet impact on a soap film

NASA Astrophysics Data System (ADS)

Kirstetter, Geoffroy; Raufaste, Christophe; Celestini, Franck

2012-09-01

We experimentally investigate the impact of a liquid jet on a soap film. We observe that the jet never breaks the film and that two qualitatively different steady regimes may occur. The first one is a refractionlike behavior obtained at small incidence angles when the jet crosses the film and is deflected by the film-jet interaction. For larger incidence angles, the jet is absorbed by the film, giving rise to a new class of flows in which the jet undulates along the film with a characteristic wavelength. Besides its fundamental interest, this paper presents a different way to guide a micrometric flow of liquid in the inertial regime and to probe foam stability submitted to violent perturbations at the soap film scale.

Jet impact on a soap film.

PubMed

Kirstetter, Geoffroy; Raufaste, Christophe; Celestini, Franck

2012-09-01

We experimentally investigate the impact of a liquid jet on a soap film. We observe that the jet never breaks the film and that two qualitatively different steady regimes may occur. The first one is a refractionlike behavior obtained at small incidence angles when the jet crosses the film and is deflected by the film-jet interaction. For larger incidence angles, the jet is absorbed by the film, giving rise to a new class of flows in which the jet undulates along the film with a characteristic wavelength. Besides its fundamental interest, this paper presents a different way to guide a micrometric flow of liquid in the inertial regime and to probe foam stability submitted to violent perturbations at the soap film scale.

Evaluation of a commercial flatbed document scanner and radiographic film scanner for radiochromic EBT film dosimetry

PubMed Central

Parker, Brent C.; Neck, Daniel W.; Henkelmann, Greg; Rosen, Isaac I.

2010-01-01

The purpose of this study was to quantify the performance and assess the utility of two different types of scanners for radiochromic EBT film dosimetry: a commercial flatbed document scanner and a widely used radiographic film scanner. We evaluated the Epson Perfection V700 Photo flatbed scanner and the Vidar VXR Dosimetry Pro Advantage scanner as measurement devices for radiochromic EBT film. Measurements were made of scan orientation effects, response uniformity, and scanner noise. Scanners were tested using films irradiated with eight separate 3×3 cm2 fields to doses ranging from 0.115–5.119 Gy. ImageJ and RIT software was used for analyzing the Epson and Vidar scans, respectively. For repeated scans of a single film, the measurements in each dose region were reproducible to within ±0.3% standard deviation (SD) with both scanners. Film‐to‐film variations for corresponding doses were measured to be within ±0.4% SD for both Epson scanner and Vidar scanners. Overall, the Epson scanner showed a 10% smaller range of pixel value compared to the Vidar scanner. Scanner noise was small: ±0.3% SD for the Epson and ±0.2% for the Vidar. Overall measurement uniformity for blank film in both systems was better than ±0.2%, provided that the leading and trailing 2 cm film edges were neglected in the Vidar system. In this region artifacts are attributed to the film rollers. Neither system demonstrated a clear measurement advantage. The Epson scanner is a relatively inexpensive method for analyzing radiochromic film, but there is a lack of commercially available software. For a clinic already using a Vidar scanner, applying it to radiochromic film is attractive because commercial software is available. However, care must be taken to avoid using the leading and trailing film edges. PACS number: 87.55.Qr

Study-Teaching Guide for the Independent Film.

ERIC Educational Resources Information Center

1972

This booklet is both an explanation of the independent film (also known as "avant-garde" or underground film) and a catalog of Grove Press' underground films, which are available for sale or rent. The topics covered include ways the independent film differs from the commercial film, the importance of and a short history of the independent film,…

Film in Education: This Worked For Me.

ERIC Educational Resources Information Center

Breen, Myles P.

Several techniques for teaching film appreciation to adults are discussed, including the use of audio cassettes, instructional films, silent films, and film dissection. Included are the techniques, philosophy, and content of a seminar on the short film, in which the short film is viewed as a variant of a short story, a pop song, a joke, and a…

"Space slitter" for film or tape

NASA Technical Reports Server (NTRS)

Johnson, W. H.

1978-01-01

Device cuts film or tape into strips by guiding film in channel under cutting blades. Device is operated by lifting pressure bar to insert blades into film. Film is then pulled through blades. Cutter has potential uses in advertising, commercial art, and publishing fields.

Geoflicks Reviewed--Films about Hawaiian Volcanoes.

ERIC Educational Resources Information Center

Bykerk-Kauffman, Ann

1994-01-01

Reviews 11 films on volcanic eruptions in the United States. Films are given a one- to five-star rating and the film's year, length, source and price are listed. Top films include "Inside Hawaiian Volcanoes" and "Kilauea: Close up of an Active Volcano." (AIM)

Low-Concentration Indium Doping in Solution-Processed Zinc Oxide Films for Thin-Film Transistors.

PubMed

Zhang, Xue; Lee, Hyeonju; Kwon, Jung-Hyok; Kim, Eui-Jik; Park, Jaehoon

2017-07-31

We investigated the influence of low-concentration indium (In) doping on the chemical and structural properties of solution-processed zinc oxide (ZnO) films and the electrical characteristics of bottom-gate/top-contact In-doped ZnO thin-film transistors (TFTs). The thermogravimetry and differential scanning calorimetry analysis results showed that thermal annealing at 400 °C for 40 min produces In-doped ZnO films. As the In content of ZnO films was increased from 1% to 9%, the metal-oxygen bonding increased from 5.56% to 71.33%, while the metal-hydroxyl bonding decreased from 72.03% to 9.63%. The X-ray diffraction peaks and field-emission scanning microscope images of the ZnO films with different In concentrations revealed a better crystalline quality and reduced grain size of the solution-processed ZnO thin films. The thickness of the In-doped ZnO films also increased when the In content was increased up to 5%; however, the thickness decreased on further increasing the In content. The field-effect mobility and on/off current ratio of In-doped ZnO TFTs were notably affected by any change in the In concentration. Considering the overall TFT performance, the optimal In doping concentration in the solution-processed ZnO semiconductor was determined to be 5% in this study. These results suggest that low-concentration In incorporation is crucial for modulating the morphological characteristics of solution-processed ZnO thin films and the TFT performance.

Influence of coolant injector configuration on film cooling effectiveness for gaseous and liquid film coolants

NASA Astrophysics Data System (ADS)

Shine, S. R.; Sunil Kumar, S.; Suresh, B. N.

2012-05-01

An experimental investigation is conducted to bring out the effects of coolant injector configuration on film cooling effectiveness, film cooled length and film uniformity associated with gaseous and liquid coolants. A series of measurements are performed using hot air as the core gas and gaseous nitrogen and water as the film coolants in a cylindrical test section simulating a thrust chamber. Straight and compound angle injection at two different configurations of 30°-10° and 45°-10° are investigated for the gaseous coolant. Tangential injection at 30° and compound angle injection at 30°-10° are examined for the liquid coolant. The analysis is based on measurements of the film-cooling effectiveness and film uniformity downstream of the injection location at different blowing ratios. Measured results showed that compound angle configuration leads to lower far-field effectiveness and shorter film length compared to tangential injection in the case of liquid film cooling. For similar injector configurations, effectiveness along the stream wise direction showed flat characteristics initially for the liquid coolant, while it was continuously dropping for the gaseous coolant. For liquid coolant, deviations in temperature around the circumference are very low near the injection point, but increases to higher values for regions away from the coolant injection locations. The study brings out the existance of an optimum gaseous film coolant injector configuration for which the effectiveness is maximum.

Realistic absorption coefficient of ultrathin films

NASA Astrophysics Data System (ADS)

Cesaria, M.; Caricato, A. P.; Martino, M.

2012-10-01

Both a theoretical algorithm and an experimental procedure are discussed of a new route to determine the absorption/scattering properties of thin films deposited on transparent substrates. Notably, the non-measurable contribution of the film-substrate interface is inherently accounted for. While the experimental procedure exploits only measurable spectra combined according to a very simple algorithm, the theoretical derivation does not require numerical handling of the acquired spectra or any assumption on the film homogeneity and substrate thickness. The film absorption response is estimated by subtracting the measured absorption spectrum of the bare substrate from that of the film on the substrate structure but in a non-straightforward way. In fact, an assumption about the absorption profile of the overall structure is introduced and a corrective factor accounting for the relative film-to-substrate thickness. The method is tested on films of a well known material (ITO) as a function of the film structural quality and influence of the film-substrate interface, both deliberately changed by thickness tuning and doping. Results are found fully consistent with information obtained by standard optical analysis and band gap values reported in the literature. Additionally, comparison with a conventional method demonstrates that our route is generally more accurate even if particularly suited for very thin films.

Flexible Ultra Moisture Barrier Film for Thin-Film Photovoltaic Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

David M. Dean

2012-10-30

Flexible Thin-film photovoltaic (TFPV) is a low cost alternative to incumbent c-Si PV products as it requires less volume of costly semiconductor materials and it can potentially reduce installation cost. Among the TFPV options, copper indium gallium diselenide (CIGS) has the highest efficiency and is believed to be one of the most attractive candidates to achieve PV cost reduction. However, CIGS cells are very moisture sensitive and require module water vapor transmission rate (WVTR) of less than 1x10-4 gram of water per square meter per day (g-H2O/m2/day). Successful development and commercialization of flexible transparent ultra moisture barrier film is themore » key to enable flexible CIGS TFPV products, and thus enable ultimate PV cost reduction. At DuPont, we have demonstrated at lab scale that we can successfully make polymer-based flexible transparent ultra moisture barrier film by depositing alumina on polymer films using atomic layer deposition (ALD) technology. The layer by layer ALD approach results in uniform and amorphous structure which effectively reduces pinhole density of the inorganic coating on the polymer, and thus allow the fabrication of flexible barrier film with WVTR of 10-5 g-H2O/m2/day. Currently ALD is a time-consuming process suitable only for high-value, relatively small substrates. To successfully commercialize the ALD-on-plastic technology for the PV industry, there is the need to scale up this technology and improve throughput. The goal of this contract work was to build a prototype demonstrating that the ALD technology could be scaled-up for commercial use. Unfortunately, the prototype failed to produce an ultra-barrier film by the close of the project.« less

Mechanical and physicochemical properties study on gellan gum thin film prepared using film casting method

NASA Astrophysics Data System (ADS)

Ismail, Nur Arifah; Razali, Mohd Hasmizam; Amin, Khairul Anuar Mat

2017-09-01

The GG thin films were prepared by film casting technique using gelzan (GG1) and kelcogel (GG2) respectively. The physical appearances of the thin films were observed and their mechanical and chemical properties were investigated. Chemical characterizations were done by Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR), UV-Vis Spectroscopy, and Scanning Electron Microscopy (SEM). Based on the ATR-FTIR result, GG1 and GG2 thin films show a broad peak in the range of 3600-3200 cm-1 assigned to -OH functional group. A broad peaks also was observed at 3000-2600 cm-1 and 1800-1600 cm-1 which are belong to -CH and C=O functional group, respectively. The UV-Vis Spectroscopy analysis shows that single absorption peak was observed at 260 nm for both films. For mechanical properties, GG1 thin film has high tensile strength (80±12), but low strain at break (2±1), on the other hand GG2 thin film has low tensile strength (3±0.08) but high strain at break (13±0.58). The Water Vapour Transmission Rates (WVTR) and swelling of GG1 and GG2 thin films were (422±113, 415±26) and (987±113, 902±63), respectively.

Horror films and psychiatry.

PubMed

Friedman, Susan Hatters; Forcen, Fernando Espi; Shand, John Preston

2014-10-01

Horror films have been popular for generations. The purpose of this article is to illustrate psychiatric conditions, themes and practice seen in horror films. Horror films often either include psychiatrists as characters or depict (Hollywood's dangerous version of) serious mental illness. Demonic possession, zombies, and 'slasher' killers are described, as well as the horror genre's characterizations of psychiatrists. © The Royal Australian and New Zealand College of Psychiatrists 2014.

Cellulose triacetate, thin film dielectric capacitor

NASA Technical Reports Server (NTRS)

Yen, Shiao-Ping S. (Inventor); Jow, T. Richard (Inventor)

1995-01-01

Very thin films of cellulose triacetate are cast from a solution containing a small amount of high boiling temperature, non-solvent which evaporates last and lifts the film from the casting surface. Stretched, oriented, crystallized films have high electrical breakdown properties. Metallized films less than about 2 microns in thickness form self-healing electrodes for high energy density, pulsed power capacitors. Thicker films can be utilized as a dielectric for a capacitor.

Cellulose triacetate, thin film dielectric capacitor

NASA Technical Reports Server (NTRS)

Yen, Shiao-Ping S. (Inventor); Jow, T. Richard (Inventor)

1993-01-01

Very thin films of cellulose triacetate are cast from a solution containing a small amount of high boiling temperature, non-solvent which evaporates last and lifts the film from the casting surface. Stretched, oriented, crystallized films have high electrical breakdown properties. Metallized films less than about 2 microns in thickness form self-healing electrodes for high energy density, pulsed power capacitors. Thicker films can be utilized as a dielectric for a capacitor.

Dual clearance squeeze film damper

NASA Technical Reports Server (NTRS)

Fleming, D. P. (Inventor)

1985-01-01

A dual clearance hydrodynamic liquid squeeze film damper for a gas turbine engine is described. Under normal operating conditions, the device functions as a conventional squeeze film damper, using only one of its oil films. When an unbalance reaches abusive levels, as may occur with a blade loss or foreign object damage, a second, larger clearance film becomes active, controlling vibration amplitudes in a near optimum manner until the engine can be safely shut down and repaired.

Low work function, stable thin films

DOEpatents

Dinh, Long N.; McLean, II, William; Balooch, Mehdi; Fehring, Jr., Edward J.; Schildbach, Marcus A.

2000-01-01

Generation of low work function, stable compound thin films by laser ablation. Compound thin films with low work function can be synthesized by simultaneously laser ablating silicon, for example, and thermal evaporating an alkali metal into an oxygen environment. For example, the compound thin film may be composed of Si/Cs/O. The work functions of the thin films can be varied by changing the silicon/alkali metal/oxygen ratio. Low work functions of the compound thin films deposited on silicon substrates were confirmed by ultraviolet photoelectron spectroscopy (UPS). The compound thin films are stable up to 500.degree. C. as measured by x-ray photoelectron spectroscopy (XPS). Tests have established that for certain chemical compositions and annealing temperatures of the compound thin films, negative electron affinity (NEA) was detected. The low work function, stable compound thin films can be utilized in solar cells, field emission flat panel displays, electron guns, and cold cathode electron guns.

Inclusions in freely suspended smectic films

NASA Astrophysics Data System (ADS)

Stannarius, Ralf; Harth, Kirsten

Smectic liquid crystal phases have a unique property: Like soap solutions, they can form stable freely suspended films. Their aspect ratios can be larger than one million to one. Such films can serve as models for two-dimensional (2D) uids, with or without in-plane anisotropy. Solid or liquid inclusions trapped in these films by capillary forces can move in the film plane and interact with other inclusions, with film thickness gradients or the film boundaries, and even with the local orientation field. We describe preparation techniques to incorporate particles or droplets in thin smectic films, and optical observation methods. Several aspects make inclusions in freely suspended films interesting research objects: They provide rich information on capillary forces as well as surface and interfacial tensions, they can serve as platforms for hydrodynamic studies in 2D, and they may help to understand coalescence dynamics at the transition from 2D to 3D...

Linking Character Strengths and Learning with Films: A Content Analysis of Films for Adolescents

ERIC Educational Resources Information Center

Phaire, Dorothy W.

2013-01-01

Despite abundant research substantiating the value of teaching with films, there is a dearth of accessible resources that can help educators select films for positive modeling of character strengths. This scarcity exists in spite of the evidence that supports the efficacy of films' influence on young people. Young people today are receiving…

Magnetron sputtered boron films

DOEpatents

Makowiecki, Daniel M.; Jankowski, Alan F.

1998-01-01

A method is described for the production of thin boron and titanium/boron films by magnetron sputter deposition. The amorphous boron films contain no morphological growth features, unlike those found when thin films are prepared by various physical vapor deposition processes. Magnetron sputter deposition method requires the use of a high density crystalline boron sputter target which is prepared by hot isostatic pressing. Thin boron films prepared by this method are useful for producing hardened surfaces, surfacing machine tools, etc. and for ultra-thin band pass filters as well as the low Z element in low Z/high Z optical components, such as mirrors which enhance reflectivity from grazing to normal incidence.

Magnetron sputtered boron films

DOEpatents

Makowiecki, D.M.; Jankowski, A.F.

1998-06-16

A method is described for the production of thin boron and titanium/boron films by magnetron sputter deposition. The amorphous boron films contain no morphological growth features, unlike those found when thin films are prepared by various physical vapor deposition processes. Magnetron sputter deposition method requires the use of a high density crystalline boron sputter target which is prepared by hot isostatic pressing. Thin boron films prepared by this method are useful for producing hardened surfaces, surfacing machine tools, etc. and for ultra-thin band pass filters as well as the low Z element in low Z/high Z optical components, such as mirrors which enhance reflectivity from grazing to normal incidence. 8 figs.

Superhydrophobic films and methods for making superhydrophobic films

DOEpatents

Aytug, Tolga; Paranthaman, Mariappan Parans; Simpson, John T.; Bogorin, Daniela Florentina

2017-09-26

This disclosure relates to methods that include depositing a first component and a second component to form a film including a plurality of nanostructures, and coating the nanostructures with a hydrophobic layer to render the film superhydrophobic. The first component and the second component can be immiscible and phase-separated during the depositing step. The first component and the second component can be independently selected from the group consisting of a metal oxide, a metal nitride, a metal oxynitride, a metal, and combinations thereof. The films can have a thickness greater than or equal to 5 nm; an average surface roughness (Ra) of from 90 to 120 nm, as measured on a 5 .mu.m.times.5 .mu.m area; a surface area of at least 20 m.sup.2/g; a contact angle with a drop of water of at least 120 degrees; and can maintain the contact angle when exposed to harsh conditions.

Anode film formation and control

DOEpatents

Koski, Oscar; Marschman, Steven C.

1990-01-01

A protective film is created about the anode within a cryolite-based electrolyte during electrolytic production of aluminum from alumina. The film function to minimize corrosion of the anode by the cryolitic electrolyte and thereby extend the life of the anode. Various operating parameters of the electrolytic process are controlled to maintain the protective film about the anode in a protective state throughout the electrolytic reduction of alumina. Such parameters include electrolyte temperature, electrolyte ratio, current density, and Al.sub.2 O.sub.3 concentration. An apparatus is also disclosed to enable identification of the onset of anode corrosion due to disruption of the film to provide real time information regarding the state of the film.

Anode film formation and control

DOEpatents

Koski, O.; Marschman, S.C.

1990-05-01

A protective film is created about the anode within a cryolite-based electrolyte during electrolytic production of aluminum from alumina. The film functions to minimize corrosion of the anode by the cryolitic electrolyte and thereby extend the life of the anode. Various operating parameters of the electrolytic process are controlled to maintain the protective film about the anode in a protective state throughout the electrolytic reduction of alumina. Such parameters include electrolyte temperature, electrolyte ratio, current density, and Al[sub 2]O[sub 3] concentration. An apparatus is also disclosed to enable identification of the onset of anode corrosion due to disruption of the film to provide real time information regarding the state of the film. 3 figs.

Tamper indicating gold nanocup plasmonic films

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeVetter, Brent M.; Bernacki, Bruce E.; Bennett, Wendy D.

The spectral signature of nanoplasmonic films are both robust and tailorable with optical responses ranging from the visible to the near-infrared. We present the development of flexible, elastomeric nanoplasmonic films consisting of periodic arrays of gold nanocups as tamper indicating films. Gold nanocups have polarization-sensitive optical properties that may be manufactured into films that offer unique advantages for tamper indication. These flexible films can be made quickly and at low-cost using commercially available monodisperse polystyrene nanospheres through self-assembly followed by plasma etching, metal deposition, and lift-off from a sacrificial substrate. Polarization- and angle-dependent optical spectroscopic measurements were performed to characterizemore » the fabricated films. Furthermore, using polarization-sensitive hyperspectral imaging, we demonstrate how these films can be applied to tamper indication and counterfeit resistance applications.« less

Method of making reflecting film reflector

DOEpatents

Cottingham, James G.

1980-01-01

A reflector of the reflecting film type is disclosed and which may be used in a heliostatic system for concentrating solar energy and comprising a reflecting film bonded to an appropriate rigid substrate in such a way that specularity of a very high order is achieved. A method of bonding the reflecting film to the substrate is also disclosed and comprises the steps of initially adhering the film to a smooth, clean flat rigid surface with a non-bonding liquid between the rigid surface and film, and then bonding the substrate and film. The non-bonding liquid has a molecular adhesion greater than any stresses due to handling or curing of the bonding agent which is applied between the film and the opposing surface of the rigid substrate.

Tamper indicating gold nanocup plasmonic films

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeVetter, Brent M.; Bernacki, Bruce E.; Bennett, Wendy D.

2017-02-13

The spectral signature of nanoplasmonic films are both robust and tailorable with optical responses ranging from the visible to the near-infrared. We present the development of flexible, elastomeric nanoplasmonic films consisting of periodic arrays of gold nanocups as tamper indicating films. Gold nanocups have polarization-sensitive optical properties that may be manufactured into films that offer unique advantages for tamper indication. These flexible films can be made quickly and at low-cost using commercially available monodisperse polystyrene nanospheres through self-assembly followed by plasma etching, metal deposition, and lift-off from a sacrificial substrate. Polarization- and angle-dependent optical spectroscopic measurements were performed to characterizemore » the fabricated films. Using polarization-sensitive hyperspectral imaging, we demonstrate how these films can be applied to tamper indication and counterfeit resistance applications.« less

Regional Film Culture: Challenges and Problems.

ERIC Educational Resources Information Center

Fountain, Alan

1978-01-01

Discusses the relationship between general film culture and state intervention through the formation of a regional film policy and the funding of film exhibition, film education, and filmmaking in Britain. Suggests ways in which intervention can perpetuate the dominant cultural ideology and ways to identify, resist, and challenge present…

Solvent annealing induced phase separation and dewetting in PMMA∕SAN blend film: film thickness and solvent dependence.

PubMed

You, Jichun; Zhang, Shuangshuang; Huang, Gang; Shi, Tongfei; Li, Yongjin

2013-06-28

The competition between "dewetting" and "phase separation" behaviors in polymer blend films attracts significant attention in the last decade. The simultaneous phase separation and dewetting in PMMA∕SAN [poly(methyl methacrylate) and poly(styrene-ran-acrylonitrile)] blend ultrathin films upon solvent annealing have been observed for the first time in our previous work. In this work, film thickness and annealing solvent dependence of phase behaviors in this system has been investigated using atomic force microscopy and grazing incidence small-angle X-ray scattering (GISAXS). On one hand, both vertical phase separation and dewetting take place upon selective solvent vapor annealing, leading to the formation of droplet∕mimic-film structures with various sizes (depending on original film thickness). On the other hand, the whole blend film dewets the substrate and produces dispersed droplets on the silicon oxide upon common solvent annealing. GISAXS results demonstrate the phase separation in the big dewetted droplets resulted from the thicker film (39.8 nm). In contrast, no period structure is detected in small droplets from the thinner film (5.1 nm and 9.7 nm). This investigation indicates that dewetting and phase separation in PMMA∕SAN blend film upon solvent annealing depend crucially on the film thickness and the atmosphere during annealing.

Using stressful films to analyze risk factors for PTSD in analogue experimental studies--which film works best?

PubMed

Weidmann, Anke; Conradi, Ania; Groger, Kathrin; Fehm, Lydia; Fydrich, Thomas

2009-10-01

To understand mental disorders, analogue paradigms provide an indispensable contribution. In posttraumatic stress disorder (PTSD), the stressful film paradigm is a frequently used analogue approach: Films depicting traumatic events are shown to non-clinical participants in order to elicit stress responses analogue to responses to traumatic events in real life. Previous studies used a large variety of films, which is problematic with regard to the comparability of results. The main goal of this study was to identify a film clip that (a) consistently provokes stress reactions and (b) provokes reactions that are as similar as possible to traumatic stress. We randomly exposed 105 male and female participants to one of four stressful films, differing, e.g., in content and origin. Intrusive memories of the film, reported immediately after the film and during a diary phase of three days, as well as distress, heart rate, and several mood states were measured. A film clip depicting rape elicited the most consistent reactions that were characterized by a higher heart rate, more distress and more intrusive memories, compared to the other three clips. Intrusive memories across all films were especially related to an increase in heart rate and disgust in response to the film.

Thermotropic Liquid Crystal Film Underwater

NASA Astrophysics Data System (ADS)

Uto, Sadahito; Nakanishi, Yuuji; Matsumoto, Takahumi

2005-05-01

A thermotropic liquid crystal film was produced in distilled water successfully. A lecithin suspension was utilized to make the film. Polarizing microscopic observations were carried out. The molecular arrangement was seemed to be homeotoropic. An expected electrooptic response of the film underwater was confirmed.

Film Sensor Device Fabricated by a Piezoelectric Poly(L-lactic acid) Film

NASA Astrophysics Data System (ADS)

Ando, Masamichi; Kawamura, Hideki; Kageyama, Keisuke; Tajitsu, Yoshiro

2012-09-01

Synthetic piezoelectric polymer films produced from petroleum feedstock have long been used as thin-film sensors and actuators. However, the fossil fuel requirements for synthetic polymer production and carbon dioxide emission from its combustion have raised concern about the environmental impact of its continued use. Eco-friendly biomass polymers, such as poly(L-lactic acid) (PLLA), are made from plant-based (vegetable starch) plastics and, thus, have a much smaller carbon footprint. Additionally, PLLA does not exhibit pyroelectricity or unnecessary poling. This suggests the usefulness of PLLA films for the human-machine interface (HMI). As an example of a new HMI, we have produced a TV remote control using a PLLA film. The intuitive operation provided by this PLLA device suggests that it is useful for the elderly or handicapped.

Dental Training Films.

ERIC Educational Resources Information Center

Veterans Administration Medical Center, Washington, DC.

This dental training films catalog is organized into two sections. Section I is a category listing of the films by number and title, indexed according to generalized headings; categories are as follow: anatomy, articulator systems, complete dentures, dental assisting, dental laboratory technology, dental materials, dental office emergencies,…

Liquid film demonstration experiment Skylab SL-4

NASA Technical Reports Server (NTRS)

Darbro, W.

1975-01-01

The liquid film demonstration experiment performed on Skylab 4 by Astronaut Gerald Carr, which involved the construction of water and soap films by boundary expansion and inertia, is discussed. Results include a 1-ml globule of water expanded into a 7-cm-diameter film as well as complex film structures produced by inertia whose lifetimes are longer in the low-g environment. Also discussed are 1-g acceleration experiments in which the unprovoked rupture of films was photographed and film lifetimes of stationary and rotated soap films were compared. Finally, there is a mathematical discussion regarding minimal surfaces, an isoperimetric problem, and liquid films.

A thin film nitinol heart valve.

PubMed

Stepan, Lenka L; Levi, Daniel S; Carman, Gregory P

2005-11-01

In order to create a less thrombogenic heart valve with improved longevity, a prosthetic heart valve was developed using thin film nitinol (NiTi). A "butterfly" valve was constructed using a single, elliptical piece of thin film NiTi and a scaffold made from Teflon tubing and NiTi wire. Flow tests and pressure readings across the valve were performed in vitro in a pulsatile flow loop. Bio-corrosion experiments were conducted on untreated and passivated thin film nitinol. To determine the material's in vivo biocompatibility, thin film nitinol was implanted in pigs using stents covered with thin film NiTi. Flow rates and pressure tracings across the valve were comparable to those through a commercially available 19 mm Perimount Edwards tissue valve. No signs of corrosion were present on thin film nitinol samples after immersion in Hank's solution for one month. Finally, organ and tissue samples explanted from four pigs at 2, 3, 4, and 6 weeks after thin film NiTi implantation appeared without disease, and the thin film nitinol itself was without thrombus formation. Although long term testing is still necessary, thin film NiTi may be very well suited for use in artificial heart valves.

Domain epitaxy for thin film growth

DOEpatents

Narayan, Jagdish

2005-10-18

A method of forming an epitaxial film on a substrate includes growing an initial layer of a film on a substrate at a temperature T.sub.growth, said initial layer having a thickness h and annealing the initial layer of the film at a temperature T.sub.anneal, thereby relaxing the initial layer, wherein said thickness h of the initial layer of the film is greater than a critical thickness h.sub.c. The method further includes growing additional layers of the epitaxial film on the initial layer subsequent to annealing. In some embodiments, the method further includes growing a layer of the film that includes at least one amorphous island.

Push Tester For Laminated Films

NASA Technical Reports Server (NTRS)

Sugimura, Russell S.

1991-01-01

Small instrument used to measure brittleness of polymer film adhesively bonded to hard substrate. Penlike instrument has microball tip. Small pointer in slot on side of instrument used to calibrate and indicate spring force applied by point. Microball dents only small area of specimen. Such measurements used to measure rates of embrittlement in environmental tests of candidate laminated-film covers for photovoltaic modules. Not limited to transparent films; also used on opaque laminated films on back panels of photovoltaic modules.

Are Wildlife Films Really "Nature Documentaries"?

ERIC Educational Resources Information Center

Bouse, Derek

1998-01-01

Examines origins of wildlife films. Outlines their tension between education and entertainment. Looks at how Disney codified wildlife films as a coherent genre by imposing conventionalized narrative frameworks upon them. Discusses factors influencing wildlife television in the 1990s. Concludes that wildlife films are a valid and distinct film and…

Picosecond laser fabrication of nanostructures on ITO film surface assisted by pre-deposited Au film

NASA Astrophysics Data System (ADS)

Yang, H. Z.; Jiang, G. D.; Wang, W. J.; Mei, X. S.; Pan, A. F.; Zhai, Z. Y.

2017-10-01

With greater optical penetration depth and lower ablation threshold fluence, it is difficult to directly fabricate large scales of laser-induced periodic surface structures (LIPSSs) on indium-tin-oxide (ITO) films. This study proposed an approach to obtain optimized LIPSSs by sputtering an Au thin film on the ITO film surface. The concept behind the proposal is that the upper layer of the thin Au film can cause surface energy aggregation, inducing the initial ripple structures. The ripples deepened and become clear with lower energy due to optical trapping. The effective mechanism of Au film was analyzed and verified by a series of experiments. Linear sweep, parallel to the laser polarization direction, was performed using a Nd:VAN laser system with 10-ps Q-switched pulse, at a central wavelength of 532 nm, with a repetition rate of 1 kHz. The complete and clear features of the nanostructures, obtained with the periods of approximately 320 nm, were observed on ITO films with proper laser fluence and scanning speed. The depth of ripples was varying in the range of 15-65 nm with clear and coherent ITO films. The preferred efficiency of fabricating nanostructures and the excellent results were obtained at a scanning speed of 2.5 mm/s and a fluence of 0.189 J/cm2. In this way, the ablation and shedding of ITO films was successfully avoided. Thus, the proposed technique can be considered to be a promising method for the laser machining of special nonmetal films.

Quantitative analysis of tear film fluorescence and discomfort during tear film instability and thinning.

PubMed

Begley, Carolyn; Simpson, Trefford; Liu, Haixia; Salvo, Eliza; Wu, Ziwei; Bradley, Arthur; Situ, Ping

2013-04-12

The purpose of this study was to test the association between tear film fluorescence changes during tear break-up (TBU) or thinning and the concurrent ocular sensory response. Sixteen subjects kept one eye open as long as possible (MBI), indicated their discomfort level continuously, and rated ocular sensations of irritation, stinging, burning, pricking, and cooling using visual analog scales (VAS). Fluorescence of the tear film was quantified by a pixel-based analysis of the median pixel intensity (PI), TBU, and percentage of dark pixels (DarkPix) over time. A cutoff of 5% TBU was used to divide subjects into either break-up (BU) or minimal break-up (BUmin) groups. Tear film fluorescence decreased (median PI) and the percentage of TBU and DarkPix increased in all trials, with the rate significantly greater in the BU than the BUmin group (Mann-Whitney U test, P < 0.05). The rate of increasing discomfort during trials was highly correlated with the rate of decrease in median PI and developing TBU (Spearman's, r ≥ 0.70). Significant correlations were found between corneal fluorescence, MBI, and sensory measures. Concentration quenching of fluorescein dye with tear film thinning best explains decreasing tear film fluorescence during trials. This was highly correlated with increasing ocular discomfort, suggesting that both tear film thinning and TBU stimulate underlying corneal nerves, although TBU produced more rapid stimulation. Slow increases in tear film hyperosmolarity may cause the gradual increase in discomfort during slow tear film thinning, whereas the sharp increases in discomfort during TBU suggest a more complex stimulus.

Low-Concentration Indium Doping in Solution-Processed Zinc Oxide Films for Thin-Film Transistors

PubMed Central

Zhang, Xue; Lee, Hyeonju; Kim, Eui-Jik; Park, Jaehoon

2017-01-01

We investigated the influence of low-concentration indium (In) doping on the chemical and structural properties of solution-processed zinc oxide (ZnO) films and the electrical characteristics of bottom-gate/top-contact In-doped ZnO thin-film transistors (TFTs). The thermogravimetry and differential scanning calorimetry analysis results showed that thermal annealing at 400 °C for 40 min produces In-doped ZnO films. As the In content of ZnO films was increased from 1% to 9%, the metal-oxygen bonding increased from 5.56% to 71.33%, while the metal-hydroxyl bonding decreased from 72.03% to 9.63%. The X-ray diffraction peaks and field-emission scanning microscope images of the ZnO films with different In concentrations revealed a better crystalline quality and reduced grain size of the solution-processed ZnO thin films. The thickness of the In-doped ZnO films also increased when the In content was increased up to 5%; however, the thickness decreased on further increasing the In content. The field-effect mobility and on/off current ratio of In-doped ZnO TFTs were notably affected by any change in the In concentration. Considering the overall TFT performance, the optimal In doping concentration in the solution-processed ZnO semiconductor was determined to be 5% in this study. These results suggest that low-concentration In incorporation is crucial for modulating the morphological characteristics of solution-processed ZnO thin films and the TFT performance. PMID:28773242

[Boleslas Matuszewki--pioneer of medical film-making].

PubMed

Matanović, Dragana

2005-01-01

Boleslas Matuszewski, born in 1856, was a pioneer in medical film-making. He worked simultaneously on improving his movie camera, film-making, collecting film documentation, and the idea of establishing an archive of medical films. Although his first attempts at filming and showing surgical operations didn't gain widespread approval, he was not discouraged, and succeeded in garnering support from a number of French doctors, who realised the importance of his ideas, not only in filming and forming medical film documentation, but also in the use of film for educative purposes. His visionary ideas gained acceptance when Dr. Doyen, on the occasion of the 66th Convention of the British Medical Society, in 1898, used film material as part of his lecture. Shortly afterwards, the Medical Academy took steps to show certain operative techniques, which represented both the confirmation and fruition of Matuszewski's ideas about filmmaking and the establishment of an archive of medical films.

Film Canister Science

ERIC Educational Resources Information Center

Ferstl, Andrew; Schneider, Jamie L.

2007-01-01

Opaque film canisters are readily available, cheap, and useful for scientific inquiry in the classroom. They can also be surprisingly versatile and useful as a tool for stimulating scientific inquiry. In this article, the authors describe inquiry activities using film canisters for preservice teachers, including a "black box" activity and several…

Historical Films in the Latin Classroom.

ERIC Educational Resources Information Center

Buller, Jeffrey L.

Guidelines and lesson plans are presented for teachers of Latin using historical films as instructional and support materials. A discussion of the use of historical films addresses these issues in classroom practice: the legality of using films in the classroom (copyrights); techniques for using historical films as sources of cultural information;…

The Harvard Project Physics Film Program

ERIC Educational Resources Information Center

Bork, Alfred M.

1970-01-01

States the philosophy behind the Harvard Project Physics (HPP) film program. Describes the three long HPP films. Lists the 48 color film loops covering six broad topics, primarily motion and energy. The 8-mm silent loops are synchronized with the text materials. Explains some of the pedagogical possibilities of these film loops. (RR)

19 CFR 12.41 - Prohibited films.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Prohibited films. 12.41 Section 12.41 Customs... SPECIAL CLASSES OF MERCHANDISE Immoral Articles § 12.41 Prohibited films. (a) Importers of films, shall certify on Customs Form 3291 that the imported films contain no obscene or immoral matter, nor any matter...

A Controlled Study on the Correlation between Tear Film Volume and Tear Film Stability in Diabetic Patients.

PubMed

Eissa, Iman M; Khalil, Noha M; El-Gendy, Heba A

2016-01-01

Purpose. To assess the tear film quantity and correlate it with the quality and stability of the tear film in diabetics and compare them to age matched controls. Introduction. Diabetes affects tear film parameters in multiple ways. Poor metabolic control and neuropathy are postulated factors. To further understand how diabetes affects tear film parameters this study was conducted. Subjects and Methods. Tear meniscus height was measured by anterior segment OCT, along with tear thinning time, a subtype of noninvasive tear break-up time, and blinking rate per minute which were all recorded for 22 diabetic patients. Correlations between these tear film parameters were studied and then compared to 16 age matched controls. Results. A statistically significant difference was found in blinking rate between the diabetic and the control group (P = 0.002), with higher blinking rate among diabetics. All tear film parameters were negatively correlated with duration of diabetes. A positive correlation was found between tear film volume and stability. Conclusion. Diabetes affects the tear film in various ways. Diabetics should be examined for dry eye signs even in absence of symptoms which may be masked by associated neuropathy. Duration of diabetes has an impact on tear film status.

Effect of Dielectric Material Films on Crystallization Characteristics of Ge2Sb2Te5 Phase-Change Memory Film

NASA Astrophysics Data System (ADS)

Nishiuchi, Kenichi; Yamada, Noboru; Kawahara, Katsumi; Kojima, Rie

2007-11-01

Reduction of the film thickness of phase-change film and the adoption of GeN- or ZrO2-based dielectric films are both effective in achieving good thermal stability in phase-change optical disks. It was experimentally confirmed that, at a heating rate of 10 °C/min, the crystallization temperature Tx of the Ge2Sb2Te5 amorphous film when sandwiched by ZnS-SiO2 films markedly increases from 162 to 197 °C, while the thickness of the Ge2Sb2Te5 film decreases from 10 to 3 nm. Tx also slightly increases when ZnS-SiO2 films are substituted for GeN-based films (from 162 to 165 °C) and ZrO2-based films (from 162 to 167 °C). At the same time, the activation energy of crystallization is 2.4 eV for both GeN- and ZrO2-based films, and is higher than 2.2 eV for ZnS-SiO2 films.

The Aesthetic Values of Film.

ERIC Educational Resources Information Center

May, Jill P.

1982-01-01

Discusses the criteria for analysis of excellence in children's films and factors involved in the production of a good film, and offers an analysis of three children's films: "The Bridge of Adam Rush,""Angel and Big Joe," and "A Pretty Kettle of Fish." Three references are provided. (EJS)

Film Fabrication Technologies at NREL

NASA Technical Reports Server (NTRS)

Mcconnell, Robert D.

1993-01-01

The National Renewable Energy Laboratory (NREL) has extensive capabilities for fabricating a variety of high-technology films. Much of the in-house work in NREL's large photovoltaics (PV) program involves the fabrication of multiple thin-film semiconducting layers constituting a thin-film PV device. NREL's smaller program in superconductivity focuses on the fabrication of superconducting films on long, flexible tape substrates. This paper focuses on four of NREL's in-house research groups and their film fabrication techniques, developed for a variety of elements, alloys, and compounds to be deposited on a variety of substrates. As is the case for many national laboratories, NREL's technology transfer efforts are focusing on Cooperative Research and Development Agreements (CRADA's) between NREL researchers and private industry researchers.

77 FR 18206 - Polyethylene Terephthalate Film, Sheet, and Strip (PET Film) From Taiwan: Extension of Time Limit...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-27

... Film, Sheet, and Strip (PET Film) From Taiwan: Extension of Time Limit for the Preliminary Results of... the antidumping duty order on PET Film from Taiwan covering the period July 1, 2010 through June 30... preliminary results of the administrative review of PET Film from Taiwan within this time limit. The...

Metallo-organic decomposition films

NASA Technical Reports Server (NTRS)

Gallagher, B. D.

1985-01-01

A summary of metallo-organic deposition (MOD) films for solar cells was presented. The MOD materials are metal ions compounded with organic radicals. The technology is evolving quickly for solar cell metallization. Silver compounds, especially silver neodecanoate, were developed which can be applied by thick-film screening, ink-jet printing, spin-on, spray, or dip methods. Some of the advantages of MOD are: high uniform metal content, lower firing temperatures, decomposition without leaving a carbon deposit or toxic materials, and a film that is stable under ambient conditions. Molecular design criteria were explained along with compounds formulated to date, and the accompanying reactions for these compounds. Phase stability and the other experimental and analytic results of MOD films were presented.

Nanostructured thermoplastic polyimide films

DOEpatents

Aglan, Heshmat

2015-05-19

Structured films containing multi-walled carbon nanotubes ("MWCNTs") have enhanced mechanical performance in terms of strength, fracture resistance, and creep recovery of polyimide ("PI") films. Preferably, the loadings of MWCNTs can be in the range of 0.1 wt % to 0.5 wt %. The strength of the new PI films dried at 60.degree. C. increased by 55% and 72% for 0.1 wt % MWCNT and 0.5 wt % MWCNT loadings, respectively, while the fracture resistance increased by 23% for the 0.1 wt % MWCNTs and then decreases at a loading of 0.5 wt % MWCNTs. The films can be advantageously be created by managing a corresponding shift in the annealing temperature at which the maximum strength occurs as the MWCNT loadings increase.

FILM WORKSHOP SUCCESSFUL WITH TSU STUDENTS.

ERIC Educational Resources Information Center

BAHRENBERG, JIM

AN UPWARD BOUND FILM WORKSHOP AT TEXAS SOUTHERN UNIVERSITY EXPOSED STUDENTS TO FILMS AS A CREATIVE ART FORM, A MEANS OF COMMUNICATION, AND A BASIS FOR DISCUSSING VALUES. IN ADDITION TO VIEWING SEVERAL SHORT, PROFESSIONALLY-DEVELOPED FILMS, STUDENTS WROTE AND PRODUCED TWO OF THEIR OWN. ONE STUDENT-PRODUCED FILM--A LIGHT SHOW--ILLUMINATED THE UNITY…

Substrate spacing and thin-film yield in chemical bath deposition of semiconductor thin films

NASA Astrophysics Data System (ADS)

Arias-Carbajal Reádigos, A.; García, V. M.; Gomezdaza, O.; Campos, J.; Nair, M. T. S.; Nair, P. K.

2000-11-01

Thin-film yield in the chemical bath deposition technique is studied as a function of separation between substrates in batch production. Based on a mathematical model, it is proposed and experimentally verified in the case of CdS thin films that the film thickness reaches an asymptotic maximum with increase in substrate separation. It is shown that at a separation less than 1 mm between substrates the yield, i.e. percentage in moles of a soluble cadmium salt deposited as a thin film of CdS, can exceed 50%. This behaviour is explained on the basis of the existence of a critical layer of solution near the substrate, within which the relevant ionic species have a higher probability of interacting with the thin-film layer than of contributing to precipitate formation. The critical layer depends on the solution composition and the temperature of the bath as well as the duration of deposition. An effective value for the critical layer thickness has been defined as half the substrate separation at which 90% of the maximum film thickness for the particular bath composition, bath temperature and duration of deposition is obtained. In the case of CdS thin films studied as an example, the critical layer is found to extend from 0.5 to 2.5 mm from the substrate surface, depending on the deposition conditions.

Films and Feelings.

ERIC Educational Resources Information Center

Gaffney, Maureen, Ed.

1981-01-01

Children's emotional responses to films are the focus of the four articles in this issue designed for media specialists and educators. Following an editorial discussing the responsibilities of media as put forth by Bruno Bettleheim, the first article presents a methodology and rationale for using story films to encourage children's exploration of…

Creative Film-Making.

ERIC Educational Resources Information Center

Smallman, Kirk

The fundamentals of motion picture photography are introduced with a physiological explanation for the illusion of motion in a film. Film stock formats and emulsions, camera features, and lights are listed and described. Various techniques of exposure control are illustrated in terms of their effects. Photographing action with a stationary or a…

FAA Film Catalog.

ERIC Educational Resources Information Center

Federal Aviation Administration (DOT), Washington, DC.

Some 75 films from the U.S. Department of Transportation's Federal Aviation Administration are listed in this catalog. Topics dealt with include aerodynamics, airports, aviation history and careers, flying clubs, navigation and weather. Most of the films are 16mm sound and color productions. Filmstrips requiring a 35mm projector and phonograph or…

Nanopatterned carbon films with engineered morphology by direct carbonization of UV-stabilized block copolymer films.

PubMed

Wang, Yong; Liu, Jinquan; Christiansen, Silke; Kim, Dong Ha; Gösele, Ulrich; Steinhart, Martin

2008-11-01

Nanopatterned thin carbon films were prepared by direct and expeditious carbonization of the block copolymer polystyrene- block-poly(2-vinylpyridine) (PS- b-P2VP) without the necessity of slow heating to the process temperature and of addition of further carbon precursors. Carbonaceous films having an ordered "dots-on-film" surface topology were obtained from reverse micelle monolayers. The regular nanoporous morphology of PS- b-P2VP films obtained by subjecting reverse micelle monolayers to swelling-induced surface reconstruction could likewise be transferred to carbon films thus characterized by ordered nanopit arrays. Stabilization of PS- b-P2VP by UV irradiation and the concurrent carbonization of both blocks were key to the conservation of the film topography. The approach reported here may enable the realization of a broad range of nanoscaled architectures for carbonaceous materials using a block copolymer ideally suited as a template because of the pronounced repulsion between its blocks and its capability to form highly ordered microdomain structures.

Scalable Production of Mechanically Robust Antireflection Film for Omnidirectional Enhanced Flexible Thin Film Solar Cells.

PubMed

Wang, Min; Ma, Pengsha; Yin, Min; Lu, Linfeng; Lin, Yinyue; Chen, Xiaoyuan; Jia, Wei; Cao, Xinmin; Chang, Paichun; Li, Dongdong

2017-09-01

Antireflection (AR) at the interface between the air and incident window material is paramount to boost the performance of photovoltaic devices. 3D nanostructures have attracted tremendous interest to reduce reflection, while the structure is vulnerable to the harsh outdoor environment. Thus the AR film with improved mechanical property is desirable in an industrial application. Herein, a scalable production of flexible AR films is proposed with microsized structures by roll-to-roll imprinting process, which possesses hydrophobic property and much improved robustness. The AR films can be potentially used for a wide range of photovoltaic devices whether based on rigid or flexible substrates. As a demonstration, the AR films are integrated with commercial Si-based triple-junction thin film solar cells. The AR film works as an effective tool to control the light travel path and utilize the light inward more efficiently by exciting hybrid optical modes, which results in a broadband and omnidirectional enhanced performance.

Scalable Production of Mechanically Robust Antireflection Film for Omnidirectional Enhanced Flexible Thin Film Solar Cells

PubMed Central

Wang, Min; Ma, Pengsha; Lu, Linfeng; Lin, Yinyue; Chen, Xiaoyuan; Jia, Wei; Cao, Xinmin; Chang, Paichun

2017-01-01

Antireflection (AR) at the interface between the air and incident window material is paramount to boost the performance of photovoltaic devices. 3D nanostructures have attracted tremendous interest to reduce reflection, while the structure is vulnerable to the harsh outdoor environment. Thus the AR film with improved mechanical property is desirable in an industrial application. Herein, a scalable production of flexible AR films is proposed with microsized structures by roll‐to‐roll imprinting process, which possesses hydrophobic property and much improved robustness. The AR films can be potentially used for a wide range of photovoltaic devices whether based on rigid or flexible substrates. As a demonstration, the AR films are integrated with commercial Si‐based triple‐junction thin film solar cells. The AR film works as an effective tool to control the light travel path and utilize the light inward more efficiently by exciting hybrid optical modes, which results in a broadband and omnidirectional enhanced performance. PMID:28932667

Dynamic delamination of patterned thin films

NASA Astrophysics Data System (ADS)

Kandula, Soma S. V.; Tran, Phuong; Geubelle, Philippe H.; Sottos, Nancy R.

2008-12-01

We investigate laser-induced dynamic delamination of a patterned thin film on a substrate. Controlled delamination results from our insertion of a weak adhesion region beneath the film. The inertial forces acting on the weakly bonded portion of the film lead to stable propagation of a crack along the film/substrate interface. Through a simple energy balance, we extract the critical energy for interfacial failure, a quantity that is difficult and sometimes impossible to characterize by more conventional methods for many thin film/substrate combinations.

76 FR 13128 - Polyethylene Terephthalate Film, Sheet, and Strip (PET Film) From Taiwan: Extension of Time Limit...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-10

... Film, Sheet, and Strip (PET Film) From Taiwan: Extension of Time Limit for the Preliminary Results of... antidumping duty order on PET Film from Taiwan covering the period July 1, 2009, through June 30, 2010. See... preliminary results of the administrative review of PET Film from Taiwan within this time limit. Specifically...

16 CFR 501.1 - Camera film.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 1 2014-01-01 2014-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk still...

16 CFR 501.1 - Camera film.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 1 2011-01-01 2011-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk still...

16 CFR 501.1 - Camera film.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 1 2012-01-01 2012-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk still...

16 CFR 501.1 - Camera film.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 16 Commercial Practices 1 2013-01-01 2013-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk still...

Using Popular Children's Films in Science

ERIC Educational Resources Information Center

Wadsworth, Elle; Croker, Stev; Harrison, Tim

2012-01-01

Watching films is a common activity for children outside of school, and incorporating popular films that contain scientific references has the potential to spark interest in the classroom. Clips rather than entire films can be used, as the children will maintain focus on the lesson objectives while being excited by the appeal of the film. The use…

16 CFR 501.1 - Camera film.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Camera film. 501.1 Section 501.1 Commercial... 500 § 501.1 Camera film. Camera film packaged and labeled for retail sale is exempt from the net... should be expressed, provided: (a) The net quantity of contents on packages of movie film and bulk still...

Instructional Film Research and the Learner.

ERIC Educational Resources Information Center

Bowie, Melvin McKinney

A brief discussion of three phases in research on instructional films--whether films can teach (approximately 1910-1950), how films teach (1940 through the late 1950s), and who learns from films (1960-1985)--introduces a review of the research literature on the third phase. The experimental studies reviewed focus on three concerns: (1) use of…

Ultrafine nanoporous palladium-aluminum film fabricated by citric acid-assisted hot-water-treatment of aluminum-palladium alloy film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harumoto, Takashi; Tamura, Yohei; Ishiguro, Takashi, E-mail: ishiguro@rs.noda.tus.ac.jp

Hot-water-treatment has been adapted to fabricate ultrafine nanoporous palladium-aluminum film from aluminum-palladium alloy film. Using citric acid as a chelating agent, a precipitation of boehmite (aluminum oxide hydroxide, AlOOH) on the nanoporous palladium-aluminum film was suppressed. According to cross-sectional scanning transmission electron microscopy observations, the ligament/pore sizes of the prepared nanoporous film were considerably small (on the order of 10 nm). Since this fabrication method only requires aluminum alloy film and hot-water with chelating agent, the ultrafine nanoporous film can be prepared simply and environmentally friendly.

Photopolymerization-based fabrication of chemical sensing films

DOEpatents

Yang, Xiaoguang; Swanson, Basil I.; Du, Xian-Xian

2003-12-30

A photopolymerization method is disclosed for attaching a chemical microsensor film to an oxide surface including the steps of pretreating the oxide surface to form a functionalized surface, coating the functionalized surface with a prepolymer solution, and polymerizing the prepolymer solution with ultraviolet light to form the chemical microsensor film. The method also allows the formation of molecular imprinted films by photopolymerization. Formation of multilayer sensing films and patterned films is allowed by the use of photomasking techniques to allow patterning of multiple regions of a selected sensing film, or creating a sensor surface containing several films designed to detect different compounds.

Magnetowetting of Ferrofluidic Thin Liquid Films

PubMed Central

Tenneti, Srinivas; Subramanian, Sri Ganesh; Chakraborty, Monojit; Soni, Gaurav; DasGupta, Sunando

2017-01-01

An extended meniscus of a ferrofluid solution on a silicon surface is subjected to axisymmetric, non-uniform magnetic field resulting in significant forward movement of the thin liquid film. Image analyzing interferometry is used for accurate measurement of the film thickness profile, which in turn, is used to determine the instantaneous slope and the curvature of the moving film. The recorded video, depicting the motion of the film in the Lagrangian frame of reference, is analyzed frame by frame, eliciting accurate information about the velocity and acceleration of the film at any instant of time. The application of the magnetic field has resulted in unique changes of the film profile in terms of significant non-uniform increase in the local film curvature. This was further analyzed by developing a model, taking into account the effect of changes in the magnetic and shape-dependent interfacial force fields. PMID:28303971

The Art of Teaching Social Studies with Film

ERIC Educational Resources Information Center

Russell, William B., III

2012-01-01

Teaching with film is a powerful and meaningful instructional strategy. This article discusses five classroom-tested methods for teaching with film: (1) film as a visual textbook, (2) film as a depicter of atmosphere, (3) film as an analogy, (4) film as a historiography, and (5) film as a springboard. Each of the methods discussed includes…

Process to form mesostructured films

DOEpatents

Brinker, C.J.; Anderson, M.T.; Ganguli, R.; Lu, Y.F.

1999-01-12

This invention comprises a method to form a family of supported films with pore size in the approximate range 0.8-20 nm exhibiting highly ordered microstructures and porosity derived from an ordered micellar or liquid-crystalline organic-inorganic precursor structure that forms during film deposition. Optically transparent, 100-500-nm thick films exhibiting a unique range of microstructures and uni-modal pore sizes are formed in seconds in a continuous coating operation. Applications of these films include sensors, membranes, low dielectric constant interlayers, anti-reflective coatings, and optical hosts. 12 figs.

Condom use and high-risk sexual acts in adult films: a comparison of heterosexual and homosexual films.

PubMed

Grudzen, Corita R; Elliott, Marc N; Kerndt, Peter R; Schuster, Mark A; Brook, Robert H; Gelberg, Lillian

2009-04-01

We compared the prevalence of condom use during a variety of sexual acts portrayed in adult films produced for heterosexual and homosexual audiences to assess compliance with state Occupational Health and Safety Administration regulations. We analyzed 50 heterosexual and 50 male homosexual films released between August 1, 2005, and July 31, 2006, randomly selected from the distributor of 85% of the heterosexual adult films released each year in the United States. Penile-vaginal intercourse was protected with condoms in 3% of heterosexual scenes. Penile-anal intercourse, common in both heterosexual (42%) and homosexual (80%) scenes, was much less likely to be protected with condoms in heterosexual than in homosexual scenes (10% vs 78%; P < .001). No penile-oral acts were protected with condoms in any of the selected films. Heterosexual films were much less likely than were homosexual films to portray condom use, raising concerns about transmission of HIV and other sexually transmitted diseases, especially among performers in heterosexual adult films. In addition, the adult film industry, especially the heterosexual industry, is not adhering to state occupational safety regulations.

Teaching Argumentative Writing through Film.

ERIC Educational Resources Information Center

Fluitt-Dupuy, Jan

2001-01-01

Discusses how watching and discussing feature films and writing reviews of these films in the English-as-a-Second/Foreign-Language classroom can be instrumental in teaching the principles of good argumentative writing within the confines of the simple movie review. Six steps for teaching a film review unit are provided. (Author/VWL)

Marangoni elasticity of flowing soap films

NASA Astrophysics Data System (ADS)

Kim, Ildoo; Mandre, Shreyas

2017-08-01

We measure the Marangoni elasticity of a flowing soap film to be 22 mN/m irrespective of its width, thickness, flow speed, or the bulk soap concentration. We perform this measurement by generating an oblique shock in the soap film and measuring the shock angle, flow speed, and thickness. We postulate that the elasticity is constant because the film surface is crowded with soap molecules. Our method allows nondestructive measurement of flowing soap film elasticity and the value 22 mN/m is likely applicable to other similarly constructed flowing soap films.

Film handling procedures for Apollo 17 lunar sounder

NASA Technical Reports Server (NTRS)

Weinstein, M. S.

1972-01-01

Film handling procedures for the Apollo 17 Lunar Sounder are itemized, including purchase of flight film, establishment of processing standards, transportation of flight films, flight film certification, application of pre- and post-sensitometry, film loading and downloading, film processing, titling, and duplication.

Zeolite-loaded poly(dimethylsiloxane) hybrid films for highly efficient thin-film microextraction of organic volatiles in water.

PubMed

Wang, Tao; Ansai, Toshihiro; Lee, Seung-Woo

2017-01-15

ZSM-5 zeolite-loaded poly(dimethylsiloxane) (PDMS) hybrid thin films were demonstrated for efficient thin-film microextraction (TFME) coupled with gas chromatography-mass spectrometry for analyzing organic volatiles in water. The extraction efficiency for a series of aliphatic alcohols and two aromatic compounds was significantly improved owing to the presence of ZSM-5 zeolites. The extraction efficiency of the hybrid films was increased in proportion to the content of ZSM-5 in the PDMS film, with 20wt% of ZSM-5 showing the best results. The 20wt% ZSM-5/PDMS hybrid film exhibited higher volatile organic content extraction compared with the single-component PDMS film or PDMS hybrid films containing other types of zeolite (e.g., SAPO-34). Limits of detection and limits of quantitation for individual analytes were in the range of 0.0034-0.049ppb and of 0.010-0.15 ppb, respectively. The effects of experimental parameters such as extraction time and temperature were optimized, and the molecular dispersion of the zeolites in/on the hybrid film matrix was confirmed with scanning electron microscopy and atomic force microscopy. Furthermore, the optimized hybrid film was preliminarily tested for the analysis of organic volatiles contained in commercially available soft drinks. Copyright © 2016 Elsevier B.V. All rights reserved.

The microjet-film interaction: the interaction and resulting shapes of a liquid microjet impacting a soap film

NASA Astrophysics Data System (ADS)

Chan, Jau Tung; Lee, Jie Liang; Tjeng, Vincent; Yeo, Ye; Tan, Guoxian

2014-11-01

The International Young Physicists’ Tournament (IYPT) is a worldwide annual competition for high-school students. This paper is adapted from the solution to problem 8, Jet and Film, as presented by the Singapore Team at the 26th IYPT, Taipei, Taiwan. The impact of liquid microjets on stable soap films was investigated. Two steady regimes were observed: refraction (where the microjet penetrates the soap film and is deflected) and absorption (where the microjet merges with the soap film and forms vertical undulating patterns on the soap film surface). This phenomenon has potential applications in controlling the trajectory of a liquid microjet in air. Although Kirstetter et al (2012) investigated this interaction by using the same liquid for both the microjet and the soap film, this paper extends their work by using different liquids for the microjet and the soap film. In addition, the need for a small-angle approximation of Snell’s law is removed for the refraction regime, and an alternative expression is proposed for the force exerted by the soap film on the microjet in the absorption regime that accounts for the dependence of the wavelength of the undulating patterns on the angle of incidence of the microjet on the soap film. Empirical data support these improved theoretical predictions.

The Energy Films Index. An Educator's Guide to Current Energy Films.

ERIC Educational Resources Information Center

Scherner, Sharon; And Others

This guide cites and describes 241 films on energy. The categories are: general films on energy, conservation of energy, history of energy development, coal, electricity, food and energy, geothermal, natural gas, nuclear energy, oil/petroleum, oil shale, solar energy, tar sands, tidal energy, wind, impacts of energy, and future of energy. For each…

Sound for Film: Audio Education for Filmmakers.

ERIC Educational Resources Information Center

Lazar, Wanda

1998-01-01

Identifies the specific, unique, and important elements of audio education required by film professionals. Presents a model unit to be included in a film studies program, either as a separate course or as part of a film production or introduction to film course. Offers a model syllabus for such a course or unit on sound in film. (SR)

Silicon nanocrystal inks, films, and methods

DOEpatents

Wheeler, Lance Michael; Kortshagen, Uwe Richard

2015-09-01

Silicon nanocrystal inks and films, and methods of making and using silicon nanocrystal inks and films, are disclosed herein. In certain embodiments the nanocrystal inks and films include halide-terminated (e.g., chloride-terminated) and/or halide and hydrogen-terminated nanocrystals of silicon or alloys thereof. Silicon nanocrystal inks and films can be used, for example, to prepare semiconductor devices.

Surface tension of flowing soap films

NASA Astrophysics Data System (ADS)

Sane, Aakash; Mandre, Shreyas; Kim, Ildoo

2018-04-01

The surface tension of flowing soap films is measured with respect to the film thickness and the concentration of soap solution. We perform this measurement by measuring the curvature of the nylon wires that bound the soap film channel and use the measured curvature to parametrize the relation between the surface tension and the tension of the wire. We find the surface tension of our soap films increases when the film is relatively thin or made of soap solution of low concentration, otherwise it approaches an asymptotic value 30 mN/m. A simple adsorption model with only two parameters describes our observations reasonably well. With our measurements, we are also able to measure Gibbs elasticity for our soap film.

Characterization of rice starch-ι-carrageenan biodegradable edible film. Effect of stearic acid on the film properties.

PubMed

Thakur, Rahul; Saberi, Bahareh; Pristijono, Penta; Golding, John; Stathopoulos, Costas; Scarlett, Christopher; Bowyer, Michael; Vuong, Quan

2016-12-01

The main aim of this study was to develop rice starch (RS), ι-carrageenan (ι-car) based film. Different formulations of RS (1-4%, w/w), ι-car (0.5-2%, w/w) was blended with stearic acid (SA; 0.3-0.9%, w/w) and glycerol (1%, w/w) as a plasticizer. The effect of film ingredients on the thickness, water vapour permeability (WVP), film solubility (FS), moisture content (MC), colour, film opacity (FO), tensile strength (TS), elongation-at-break (EAB) of film was examined. Interactions and miscibility of partaking components was studied by using Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). Hydrocolloid suspension solution of mix polysaccharides imparted a significant impact (p<0.05) on the important attributes of resulting edible film. TS and EAB of film were improved significantly (p<0.05) when ι-car was increased in the film matrix. Formulation F1 comprising 2% ι-car, 2% RS, 0.3% SA, Gly 30% w/w and 0.2% surfactant (tween ® 20) provided film with good physical, mechanical and barrier properties. FT-IR and XRD results reveal that molecular interactions between RS-ι-car have a great impact on the film properties confining the compatibility and miscibility of mixed polysaccharide. Results of the study offers new biodegradable formulation for application on fruit and vegetables. Copyright © 2016 Elsevier B.V. All rights reserved.

Fibronectin-based multilayer thin films.

PubMed

Gand, Adeline; Tabuteau, Maud; Chat, Coline; Ladam, Guy; Atmani, Hassan; Van Tassel, Paul R; Pauthe, Emmanuel

2017-08-01

Thin films mimicking the structure and composition of the extra-cellular matrix (ECM) are potentially attractive as biomaterials for cell contacting applications. Layer-by-layer (LbL) assembly of a biological polycation, poly(l-lysine) (PLL), and a common ECM protein, fibronectin (Fn), was employed here to construct nanoscale, ECM mimicking films. Incremental film thickness and interfacial charge magnitude are observed to diminish with layer number, resulting in sub-linear film growth scaling and saturation after about 10 layers. Infrared spectroscopy and electron microscopy together reveal the formation of Fn containing aggregates, whose presence correlates with diminished charge reversal and suppressed LbL assembly. PLL-Fn films induce a significantly greater murine MC3T3-E1 pre-osteoblastic cell proliferation, while maintaining a much higher proportion of Fn in the molecular (as opposed to fibrillar) state, compared to a Fn monolayer, suggesting the enhanced Fn content of these ECM-mimicking films to significantly, and positively, affect cell behavior. Copyright © 2017 Elsevier B.V. All rights reserved.

Variable temperature semiconductor film deposition

DOEpatents

Li, X.; Sheldon, P.

1998-01-27

A method of depositing a semiconductor material on a substrate is disclosed. The method sequentially comprises (a) providing the semiconductor material in a depositable state such as a vapor for deposition on the substrate; (b) depositing the semiconductor material on the substrate while heating the substrate to a first temperature sufficient to cause the semiconductor material to form a first film layer having a first grain size; (c) continually depositing the semiconductor material on the substrate while cooling the substrate to a second temperature sufficient to cause the semiconductor material to form a second film layer deposited on the first film layer and having a second grain size smaller than the first grain size; and (d) raising the substrate temperature, while either continuing or not continuing to deposit semiconductor material to form a third film layer, to thereby anneal the film layers into a single layer having favorable efficiency characteristics in photovoltaic applications. A preferred semiconductor material is cadmium telluride deposited on a glass/tin oxide substrate already having thereon a film layer of cadmium sulfide.

Variable temperature semiconductor film deposition

DOEpatents

Li, Xiaonan; Sheldon, Peter

1998-01-01

A method of depositing a semiconductor material on a substrate. The method sequentially comprises (a) providing the semiconductor material in a depositable state such as a vapor for deposition on the substrate; (b) depositing the semiconductor material on the substrate while heating the substrate to a first temperature sufficient to cause the semiconductor material to form a first film layer having a first grain size; (c) continually depositing the semiconductor material on the substrate while cooling the substrate to a second temperature sufficient to cause the semiconductor material to form a second film layer deposited on the first film layer and having a second grain size smaller than the first grain size; and (d) raising the substrate temperature, while either continuing or not continuing to deposit semiconductor material to form a third film layer, to thereby anneal the film layers into a single layer having favorable efficiency characteristics in photovoltaic applications. A preferred semiconductor material is cadmium telluride deposited on a glass/tin oxide substrate already having thereon a film layer of cadmium sulfide.

TFOS DEWS II Tear Film Report.

PubMed

Willcox, Mark D P; Argüeso, Pablo; Georgiev, Georgi A; Holopainen, Juha M; Laurie, Gordon W; Millar, Tom J; Papas, Eric B; Rolland, Jannick P; Schmidt, Tannin A; Stahl, Ulrike; Suarez, Tatiana; Subbaraman, Lakshman N; Uçakhan, Omür Ö; Jones, Lyndon

2017-07-01

The members of the Tear Film Subcommittee reviewed the role of the tear film in dry eye disease (DED). The Subcommittee reviewed biophysical and biochemical aspects of tears and how these change in DED. Clinically, DED is characterized by loss of tear volume, more rapid breakup of the tear film and increased evaporation of tears from the ocular surface. The tear film is composed of many substances including lipids, proteins, mucins and electrolytes. All of these contribute to the integrity of the tear film but exactly how they interact is still an area of active research. Tear film osmolarity increases in DED. Changes to other components such as proteins and mucins can be used as biomarkers for DED. The Subcommittee recommended areas for future research to advance our understanding of the tear film and how this changes with DED. The final report was written after review by all Subcommittee members and the entire TFOS DEWS II membership. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of Graphene-EC on Ag NW-Based Transparent Film Heaters: Optimizing the Stability and Heat Dispersion of Films.

PubMed

Cao, Minghui; Wang, Minqiang; Li, Le; Qiu, Hengwei; Yang, Zhi

2018-01-10

To optimize the performance of silver nanowire (Ag NW) film heaters and explore the effect of graphene on a film, we introduced poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) and graphene modified with ethyl cellulose (graphene-EC) into the film. The high-quality and well-dispersed graphene-EC was synthesized from graphene obtained by electrochemical exfoliation as a precursor. The transparent film heaters were fabricated via spin-coating. With the assistance of graphene-EC, the stability of film heaters was greatly improved, and the conductivity was optimized by adjusting the Ag NW concentration. The film heaters exhibited a fast and accurate response to voltage, accompanied by excellent environmental endurance, and there was no significant performance degradation after being operated for a long period of time. These results indicate that graphene-EC plays a crucial role in optimizing film stability and heat dispersion in the film. The Ag NW/PEDOT:PSS-doped graphene-EC film heaters show a great potential in low-cost indium-tin-oxide-free flexible transparent electrodes, heating systems, and transparent film heaters.

Film as Revolutionary Weapon: A Pedagogical Analysis. Latin American Studies Program, Film Series No. 3.

ERIC Educational Resources Information Center

California Univ., Riverside. Latin American Studies Program.

This paper describes a university course designed to examine the use of film as a revolutionary medium in Latin American countries. Objectives of the course were to illustrate the complexity of studying a film genre, develop an analytical framework for comparing revolutionary films, and encourage students to reach their own conclusions about the…

Film Analysis through Linguistic Base

ERIC Educational Resources Information Center

Tanriverdi, Belgin

2007-01-01

Studies made in the last few years show that using films in language classrooms is an effective way in teaching a foreign language. Well-chosen films can serve as a valuable pedagogical aid, both for classroom use and self-study. This article is about using films in language classrooms through a specially designed course, whose outline description…

The erotic in film and in mass psychology.

PubMed

Kernberg, O F

1994-01-01

The medium of film offers a vivid demonstration of the ongoing tension between conventional morality and mature, passionate love. While film activates mass psychology and therefore conventionality, the erotic in film threatens conventional boundaries. The dialectic thus involved in erotic art in film, the conventional film, and pornography sheds light on the unconscious motivations for accepting or rejecting the erotic. The author highlights relevant psychoanalytic theories to help formulate the nature of the erotic in film as well as the structures of the erotic film, the conventional film, and pornography. After discussing several examples, he concludes that both the conventional film and pornography are unconscious allies in opposing mature, passionate love.

Light guiding properties of soap films

NASA Astrophysics Data System (ADS)

Emile, Janine; Emile, Olivier; Casanova, Federico

2013-02-01

The injection of a laser beam from the side in a horizontal free-standing draining soap film is reported. We observe the self-deflection of the beam that varies in a random way. The film thinning is affected by the injection and depends on the polarization of the light beam, not on the laser power. The liquid in the soap film is ejected towards the meniscus, without modifying its molecular structure. Besides, this injection seems to stabilize the film near the light beam propagation and to destabilize the film in the other zones. Consequences and applications are then discussed.

Trout skin gelatin-based edible film development.

PubMed

Kim, Dayeon; Min, Sea C

2012-09-01

Edible biopolymer films were developed from gelatin extracted from trout skin (TSG) using thermal protein denaturation conditions and plasticizer (glycerol) concentration as variables. The amino acid composition of the TSG, elastic modulus, viscous modulus, and the viscosity of film-forming solutions, and tensile properties, water vapor permeability, solubility in water, and color of TSG-based films were determined. A 6.8% (w/w, wet basis) trout skin-extracted gelatin solution containing 9, 17, or 23% (w/w, dry basis) glycerol was heated at 80, 90, or 100 °C for 30, 45, or 60 min to prepare a film-forming solution. TSG can be characterized as a gelatin containing high contents of methionine and aspartic acid. The gelation temperature of the film-forming solution was 7 °C and the solution was subjected to heating to form a stable matrix for a film. Increased heating time of the film-forming solution reduced the film solubility (P < 0.05). Heating at 90 °C for 30 min was suggested as the requirement for film formation. As the concentration of glycerol in the film increased, film strength and moisture barrier properties decreased, while film stretchability increased (P < 0.05). Trout skin by-products can be used as a natural protein source for fabricating biopolymer films stable at ambient conditions with certain physical and moisture barrier properties by controlling thermal treatment conditions and glycerol concentrations. The fishing industry produces a significant amount of waste, including fish skin, due to fish processing. Trout skin waste has potential value as a protein source that can be used to form biopolymer edible films for packaging low and intermediate water activity food products, and thus may have practical applications in the food industry, which could be one way to cut waste disposal in the trout processing industry. © 2012 Institute of Food Technologists®

Crystallization behavior of amorphous indium-gallium-zinc-oxide films and its effects on thin-film transistor performance

NASA Astrophysics Data System (ADS)

Suko, Ayaka; Jia, JunJun; Nakamura, Shin-ichi; Kawashima, Emi; Utsuno, Futoshi; Yano, Koki; Shigesato, Yuzo

2016-03-01

Amorphous indium-gallium-zinc oxide (a-IGZO) films were deposited by DC magnetron sputtering and post-annealed in air at 300-1000 °C for 1 h to investigate the crystallization behavior in detail. X-ray diffraction, electron beam diffraction, and high-resolution electron microscopy revealed that the IGZO films showed an amorphous structure after post-annealing at 300 °C. At 600 °C, the films started to crystallize from the surface with c-axis preferred orientation. At 700-1000 °C, the films totally crystallized into polycrystalline structures, wherein the grains showed c-axis preferred orientation close to the surface and random orientation inside the films. The current-gate voltage (Id-Vg) characteristics of the IGZO thin-film transistor (TFT) showed that the threshold voltage (Vth) and subthreshold swing decreased markedly after the post-annealing at 300 °C. The TFT using the totally crystallized films also showed the decrease in Vth, whereas the field-effect mobility decreased considerably.

The Educational Film Industry

ERIC Educational Resources Information Center

Tortora, Vincent R.; Schillaci, Peter

1975-01-01

Increased dialog is needed among educational film producers, distributors, and consumers in order to be sure that what is being produced meets educators' needs and also to help solve the financial problems of the film industry. (LS)

Effect of electron-beam deposition process variables on the film characteristics of the CrOx films

NASA Astrophysics Data System (ADS)

Chiu, Po-kai; Liao, Yi-Ting; Tsai, Hung-Yin; Chiang, Donyau

2018-02-01

The film characteristics and optical properties of the chromium oxide films on the glass substrates prepared by electron-beam deposition with different process variables were investigated. The process variables included are the various oxygen flow rates, the different applied substrate temperatures, and the preparation process in Ar or O2 surrounding environment with and without ion-assisted deposition. The optical constants of the deposited films are determined from the reflectance and transmittance measurements obtained using a spectrophotometer with wavelengths ranging from 350 nm to 2000 nm. The microstructures of the films were examined by the XRD, SEM, and XPS. The electrical conductivity was measured by a four-point probe instrument. The resulting microstructures of all the prepared films are amorphous and the features of the films are dense, uniform and no pillar structure is observed. The refractive index of deposited films decrease with oxygen flow rate increase within studied wavelengths and the extinction coefficients have the same trend in wavelengths of UV/Vis ranges. Increasing substrate temperature to 200 oC results in increase of both refractive index and extinction coefficient, but substrate temperatures below 150 oC show negligible effect on optical constants. The optical and electrical properties in the prepared CrOx films are illustrated by the analyzed XPS results, which decompose the enveloped curve of chromium electron energy status into the constituents of metal Cr, oxides CrO2 and Cr2O3. The relative occupied area contributed from metal Cr and area contributed from the other oxides can express the concentration ratio of free electron to covalent bonds in deposited films and the ratio is applied to explain the film characteristics, including the optical constants and sheet resistance.

Polymer thin film as coating layer to prevent corrosion of metal/metal oxide film

NASA Astrophysics Data System (ADS)

Sarkar, Suman; Kundu, Sarathi

2018-04-01

Thin film of polymer is used as coating layer and the corrosion of metal/metal oxide layer is studied with the variation of the thickness of the coating layer. The thin layer of polystyrene is fabricated using spin coating method on copper oxide (CuO) film which is deposited on glass substrate using DC magnetron sputtering technique. Thickness of the polystyrene and the CuO layers are determined using X-ray reflectivity (XRR) technique. CuO thin films coated with the polystyrene layer are exposed to acetic acid (2.5 v/v% aqueous CH3COOH solution) environments and are subsequently analyzed using UV-Vis spectroscopy and atomic force microscopy (AFM). Surface morphology of the film before and after interaction with the acidic environment is determined using AFM. Results obtained from the XRR and UV-Vis spectroscopy confirm that the thin film of polystyrene acts as an anticorrosion coating layer and the strength of the coating depends upon the polymer layer thickness at a constant acid concentration.

Viscous bursting of suspended films

NASA Astrophysics Data System (ADS)

Debrégeas, G.; Martin, P.; Brochard-Wyart, F.

1995-11-01

Soap films break up by an inertial process. We present here the first observations on freely suspended films of long-chain polymers, where viscous effects are dominant and no surfactant is present. A hole is nucleated at time 0 and grows up to a radius R(t) at time t. A surprising feature is that the liquid from the hole is not collected into a rim (as it is in soap films): The liquid spreads out without any significant change of the film thickness. The radius R(t) grows exponentially with time, R~exp(t/τ) [while in soap films R(t) is linear]. The rise time τ~ηe/2γ where η is viscosity, e is thickness (in the micron range), and γ is surface tension. A simple model is developed to explain this growth law.

Vanadium dioxide film protected with an atomic-layer-deposited Al{sub 2}O{sub 3} thin film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiao; Cao, Yunzhen, E-mail: yzhcao@mail.sic.ac.cn; Yang, Chao

2016-01-15

A VO{sub 2} film exposed to ambient air is prone to oxidation, which will degrade its thermochromic properties. In this work, the authors deposited an ultrathin Al{sub 2}O{sub 3} film with atomic layer deposition (ALD) to protect the underlying VO{sub 2} film from degradation, and then studied the morphology and crystalline structure of the films. To assess the protectiveness of the Al{sub 2}O{sub 3} capping layer, the authors performed a heating test and a damp heating test. An ultrathin 5-nm-thick ALD Al{sub 2}O{sub 3} film was sufficient to protect the underlying VO{sub 2} film heated at 350 °C. However, in amore » humid environment at prolonged durations, a thicker ALD Al{sub 2}O{sub 3} film (15 nm) was required to protect the VO{sub 2}. The authors also deposited and studied a TiO{sub 2}/Al{sub 2}O{sub 3} bilayer, which significantly improved the protectiveness of the Al{sub 2}O{sub 3} film in a humid environment.« less

Plasmonic extinction in gold nanoparticle-polymer films as film thickness and nanoparticle separation decrease below resonant wavelength

NASA Astrophysics Data System (ADS)

Dunklin, Jeremy R.; Bodinger, Carter; Forcherio, Gregory T.; Keith Roper, D.

2017-01-01

Plasmonic nanoparticles embedded in polymer films enhance optoelectronic properties of photovoltaics, sensors, and interconnects. This work examined optical extinction of polymer films containing randomly dispersed gold nanoparticles (AuNP) with negligible Rayleigh scattering cross-sections at particle separations and film thicknesses less than (sub-) to greater than (super-) the localized surface plasmon resonant (LSPR) wavelength, λLSPR. Optical extinction followed opposite trends in sub- and superwavelength films on a per nanoparticle basis. In ˜70-nm-thick polyvinylpyrrolidone films containing 16 nm AuNP, measured resonant extinction per particle decreased as particle separation decreased from ˜130 to 76 nm, consistent with trends from Maxwell Garnett effective medium theory and coupled dipole approximation. In ˜1-mm-thick polydimethylsiloxane films containing 16-nm AuNP, resonant extinction per particle plateaued at particle separations ≥λLSPR, then increased as particle separation radius decreased from ˜514 to 408 nm. Contributions from isolated particles, interparticle interactions and heterogeneities in sub- and super-λLSPR films containing AuNP at sub-λLSPR separations were examined. Characterizing optoplasmonics of thin polymer films embedded with plasmonic NP supports rational development of optoelectronic, biomedical, and catalytic activity using these nanocomposites.

Condom Use and High-Risk Sexual Acts in Adult Films: A Comparison of Heterosexual and Homosexual Films

PubMed Central

Elliott, Marc N.; Kerndt, Peter R.; Schuster, Mark A.; Brook, Robert H.; Gelberg, Lillian

2009-01-01

Objectives. We compared the prevalence of condom use during a variety of sexual acts portrayed in adult films produced for heterosexual and homosexual audiences to assess compliance with state Occupational Health and Safety Administration regulations. Methods. We analyzed 50 heterosexual and 50 male homosexual films released between August 1, 2005, and July 31, 2006, randomly selected from the distributor of 85% of the heterosexual adult films released each year in the United States. Results. Penile–vaginal intercourse was protected with condoms in 3% of heterosexual scenes. Penile–anal intercourse, common in both heterosexual (42%) and homosexual (80%) scenes, was much less likely to be protected with condoms in heterosexual than in homosexual scenes (10% vs 78%; P < .001). No penile–oral acts were protected with condoms in any of the selected films. Conclusions. Heterosexual films were much less likely than were homosexual films to portray condom use, raising concerns about transmission of HIV and other sexually transmitted diseases, especially among performers in heterosexual adult films. In addition, the adult film industry, especially the heterosexual industry, is not adhering to state occupational safety regulations. PMID:19218178

Do Films Make You Learn? Inference Processes in Expository Film Comprehension

ERIC Educational Resources Information Center

Tibus, Maike; Heier, Anke; Schwan, Stephan

2013-01-01

The present article examines how suitable expository films are for learning. This question was motivated by the assumption that films are processed in a superficial manner. However, previous research has been dominated by the analyses of outcome measures and has never taken a look at online measures so that no clear conclusions have been drawn.…

Film As Art.

ERIC Educational Resources Information Center

Arnheim, Rudolf

The thesis of this classic, the major part of which was originally published in 1933, is that the peculiar virtues of film as art derive from an exploitation of the limitations of the medium: the absence of sound, the absence of color, the lack of three-dimensional depth. Silent-film artists made virtues of these necessities and were on their way…

Radical Pedagogy, Prison, and Film

ERIC Educational Resources Information Center

O'Neill, Dierdre

2015-01-01

This article explores the work of The Inside Film project. Inside Film works with a specific group of people (prisoners and ex-prisoners) in a particular set of circumstances (in prison or on parole) exploring how film making can be used within prison education or with people who have been to prison as a means of fostering a critical engagement…

Self-Limited Growth in Pentacene Thin Films

PubMed Central

2017-01-01

Pentacene is one of the most studied organic semiconducting materials. While many aspects of the film formation have already been identified in very thin films, this study provides new insight into the transition from the metastable thin-film phase to bulk phase polymorphs. This study focuses on the growth behavior of pentacene within thin films as a function of film thickness ranging from 20 to 300 nm. By employing various X-ray diffraction methods, combined with supporting atomic force microscopy investigations, one crystalline orientation for the thin-film phase is observed, while three differently tilted bulk phase orientations are found. First, bulk phase crystallites grow with their 00L planes parallel to the substrate surface; second, however, crystallites tilted by 0.75° with respect to the substrate are found, which clearly dominate the former in ratio; third, a different bulk phase polymorph with crystallites tilted by 21° is found. The transition from the thin-film phase to the bulk phase is rationalized by the nucleation of the latter at crystal facets of the thin-film-phase crystallites. This leads to a self-limiting growth of the thin-film phase and explains the thickness-dependent phase behavior observed in pentacene thin films, showing that a large amount of material is present in the bulk phase much earlier during the film growth than previously thought. PMID:28287698

Tear film measurement by optical reflectometry technique

PubMed Central

Lu, Hui; Wang, Michael R.; Wang, Jianhua; Shen, Meixiao

2014-01-01

Abstract. Evaluation of tear film is performed by an optical reflectometer system with alignment guided by a galvanometer scanner. The reflectometer system utilizes optical fibers to deliver illumination light to the tear film and collect the film reflectance as a function of wavelength. Film thickness is determined by best fitting the reflectance-wavelength curve. The spectral reflectance acquisition time is 15 ms, fast enough for detecting film thickness changes. Fast beam alignment of 1 s is achieved by the galvanometer scanner. The reflectometer was first used to evaluate artificial tear film on a model eye with and without a contact lens. The film thickness and thinning rate have been successfully quantified with the minimum measured thickness of about 0.3 μm. Tear films in human eyes, with and without a contact lens, have also been evaluated. A high-contrast spectral reflectance signal from the precontact lens tear film is clearly observed, and the thinning dynamics have been easily recorded from 3.69 to 1.31 μm with lipid layer thickness variation in the range of 41 to 67 nm. The accuracy of the measurement is better than ±0.58% of the film thickness at an estimated tear film refractive index error of ±0.001. The fiber-based reflectometer system is compact and easy to handle. PMID:24500519

Self-Limited Growth in Pentacene Thin Films.

PubMed

Pachmajer, Stefan; Jones, Andrew O F; Truger, Magdalena; Röthel, Christian; Salzmann, Ingo; Werzer, Oliver; Resel, Roland

2017-04-05

Pentacene is one of the most studied organic semiconducting materials. While many aspects of the film formation have already been identified in very thin films, this study provides new insight into the transition from the metastable thin-film phase to bulk phase polymorphs. This study focuses on the growth behavior of pentacene within thin films as a function of film thickness ranging from 20 to 300 nm. By employing various X-ray diffraction methods, combined with supporting atomic force microscopy investigations, one crystalline orientation for the thin-film phase is observed, while three differently tilted bulk phase orientations are found. First, bulk phase crystallites grow with their 00L planes parallel to the substrate surface; second, however, crystallites tilted by 0.75° with respect to the substrate are found, which clearly dominate the former in ratio; third, a different bulk phase polymorph with crystallites tilted by 21° is found. The transition from the thin-film phase to the bulk phase is rationalized by the nucleation of the latter at crystal facets of the thin-film-phase crystallites. This leads to a self-limiting growth of the thin-film phase and explains the thickness-dependent phase behavior observed in pentacene thin films, showing that a large amount of material is present in the bulk phase much earlier during the film growth than previously thought.

Thin film hydrogen sensor

DOEpatents

Cheng, Y.T.; Poli, A.A.; Meltser, M.A.

1999-03-23

A thin film hydrogen sensor includes a substantially flat ceramic substrate with first and second planar sides and a first substrate end opposite a second substrate end; a thin film temperature responsive resistor on the first planar side of the substrate proximate to the first substrate end; a thin film hydrogen responsive metal resistor on the first planar side of the substrate proximate to the fist substrate end and proximate to the temperature responsive resistor; and a heater on the second planar side of the substrate proximate to the first end. 5 figs.

Liquid-film electron stripper

DOEpatents

Leemann, Beat T.; Yourd, Roland B.

1984-01-01

A thin freestanding oil film is produced in vacuum by directing an oil stream radially inward to the hollow-ground sharp outer edge of a rotating disc. The sides of the edge are roughened somewhat to aid in dispersing oil from the disc. Oil is removed from the surface of disc to prevent formation of oil droplets which might spin off the disc and disrupt the oil film. An ion beam is directed through the thin oil film so that electrons are stripped from the ions to increase their charge.

Thin film hydrogen sensor

DOEpatents

Cheng, Yang-Tse; Poli, Andrea A.; Meltser, Mark Alexander

1999-01-01

A thin film hydrogen sensor, includes: a substantially flat ceramic substrate with first and second planar sides and a first substrate end opposite a second substrate end; a thin film temperature responsive resistor on the first planar side of the substrate proximate to the first substrate end; a thin film hydrogen responsive metal resistor on the first planar side of the substrate proximate to the fist substrate end and proximate to the temperature responsive resistor; and a heater on the second planar side of the substrate proximate to the first end.

Liquid-film electron stripper

DOEpatents

Leemann, B.T.; Yourd, R.B.

1982-03-09

A thin freestanding oil film is produced in vacuum by directing an oil stream radially inward to the hollow-ground sharp outer edge of a rotating disc. The sides of the edge are roughened somewhat to aid in dispersing oil from the disc. Oil is removed from the surface of disc to prevent formation of oil droplets which might spin off the disc and disrupt the oil film. An ion beam is directed through the thin oil film so that electrons are stripped from the ions to increase their charge.

High density nonmagnetic cobalt in thin films

NASA Astrophysics Data System (ADS)

Banu, Nasrin; Singh, Surendra; Basu, Saibal; Roy, Anupam; Movva, Hema C. P.; Lauter, V.; Satpati, B.; Dev, B. N.

2018-05-01

Recently high density (HD) nonmagnetic cobalt has been discovered in a nanoscale cobalt thin film, grown on Si(111) single crystal. This form of cobalt is not only nonmagnetic but also superconducting. These promising results have encouraged further investigations of the growth of the nonmagnetic (NM) phase of cobalt. In the original investigation, the cobalt film had a natural cobalt oxide at the top. We have investigated whether the growth of HD NM cobalt layers in the thin film depends on (i) a capping layer on the cobalt film, (ii) the thickness of the cobalt film and (iii) the nature of the substrate on which the cobalt film is grown. The results of such investigations indicate that for cobalt films capped with a thin gold layer, and for various film thicknesses, HD NM cobalt layers are formed. However, instead of a Si substrate, when the cobalt films are grown on oxide substrates, such as silicon oxide or cobalt oxide, HD NM cobalt layers are not formed. The difference is attributed to the nature—crystalline or amorphous—of the substrate.

Cultural Dependency in Canada's Feature Film Industry.

ERIC Educational Resources Information Center

Pendakur, Manjunath

1981-01-01

Examines the ownership and policies of the dominant firms in the Canadian film market to explain Canada's dependence on imported films. Demonstrates how the economic relations existing between Canadian and U.S. film industries limit the profitability of films made in Canada. (JMF)

Oromucosal film preparations: classification and characterization methods.

PubMed

Preis, Maren; Woertz, Christina; Kleinebudde, Peter; Breitkreutz, Jörg

2013-09-01

Recently, the regulatory authorities have enlarged the variety of 'oromucosal preparations' by buccal films and orodispersible films. Various film preparations have entered the market and pharmacopoeias. Due to the novelty of the official monographs, no standardized characterization methods and quality specifications are included. This review reports the methods of choice to characterize oromucosal film preparations with respect to biorelevant characterization and quality control. Commonly used dissolution tests for other dosage forms are not transferable for films in all cases. Alternatives and guidance on decision, which methods are favorable for film preparations are discussed. Furthermore, issues about requirements for film dosage forms are reflected. Oromucosal film preparations offer a wide spectrum of opportunities. There are a lot of suggestions in the literature on how to control the quality of these innovative products, but no standardized tests are available. Regulatory authorities need to define the standards and quality requirements more precisely.

A Film Program in a Teaching Hospital *

PubMed Central

Meiboom, Esther

1973-01-01

The Martland Hospital Medical Library has for more than a year been conducting a 16mm film program for interns, residents, attending physicians, and nurses as an adjunct to continuing education. It was possible to run this project on a minimal budget because many films are available at little or no cost from governmental agencies, pharmaceutical companies, medical associations, and universities. The program is run on a departmental basis. Films for a department are selected by the chief resident in that department from a list which the librarian has prepared of available films in the specialty involved. The library orders and publicizes the films and transacts all business in connection with them. Films pertinent to clinical practice are preferred. The administration of this program is described in this paper, and a number of film catalogs are evaluated. Criteria for film selection are discussed. PMID:4800293

Redox-Switchable Surface Wrinkling on Polyaniline Film.

PubMed

Xie, Jixun; Zong, Chuanyong; Han, Xue; Ji, Haipeng; Wang, Juanjuan; Yang, Xiu; Lu, Conghua

2016-04-01

Here the redox-driven switch between the wrinkled and dewrinkled states on poly-aniline (PANI) film is reported. This switch is derived from the reversible transition in different intrinsic redox states of polyaniline (e.g., between emeraldine salt (ES) and leucoemeraldine base (LEB) or between ES and pernigraniline base (PB)) that are involved in the redox reaction, coupled with the corresponding volume expansion/shrinkage. Interestingly, the as-wrinkled ES film becomes deswollen and dewrinkled when reduced to the LEB state or oxidized to the PB state. Conversely, oxidation of the LEB film or reduction of the PB film into the swollen ES film leads to the reoccurrence of surface wrinkling. Furthermore, the reducibility of the dewrinkled LEB film and the oxidizability of the dewrinkled PB film are well utilized respectively to yield various wrinkled PANI-based composite films. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sensitometric and image analysis of T-grain film.

PubMed

Thunthy, K H; Weinberg, R

1986-08-01

The new Kodak T-grain film is the result of a new technology that makes fast films with high image resolution. The purpose of the investigation was to determine the sensitometric properties and image quality of a T-grain film (T-Mat G) and also to compare this film with a green-sensitive orthochromatic film (Ortho G) and a blue-sensitive film (XRP). The criteria for film evaluation were relative speed, average contrast, exposure latitude, and image resolution. The results showed that the T-Mat G film is twice as fast as the X-Omat RP film and, one and one-third times as fast as the Ortho G film. T-Mat G also produces high resolution and high contrast. This is contrary to the widely held notion that speed is inversely proportional to image quality.

Metal-organic chemical vapor deposition of cerium oxide, gallium-indium-oxide, and magnesium oxide thin films: Precursor design, film growth, and film characterization

NASA Astrophysics Data System (ADS)

Edleman, Nikki Lynn

A new class of volatile, low-melting, fluorine-free lanthanide metal-organic chemical vapor deposition (MOCVD) precursors has been developed. The neutral, monomeric cerium, neodymium, gadolinium, and erbium complexes are coordinatively saturated by a versatile, multidentate, ether-functionalized beta-ketoiminate ligand, and complex melting point and volatility characteristics can be tuned by altering the alkyl substituents on the ligand periphery. Direct comparison with lanthanide beta-diketonate complexes reveals that the present precursor class is a superior choice for lanthanide oxide MOCVD. Epitaxial CeO 2 buffer layer films have been grown on (001) YSZ substrates by MOCVD at significantly lower temperatures than previously reported using one of the newly developed cerium precursors. High-quality YBCO films grown on these CeO2 buffer layers by POMBE exhibit very good electrical transport properties. The cerium complex has therefore been explicitly demonstrated to be a stable and volatile precursor and is attractive for low-temperature growth of coated conductor multilayer structures by MOCVD. Gallium-indium-oxide thin films (GaxIn2-xO 3), x = 0.0˜1.1, have been grown by MOCVD using the volatile metal-organic precursors In(dpm)3 and Ga(dpm)3. The films have a homogeneously Ga-substituted, cubic In2O3 microstructure randomly oriented on quartz or heteroepitaxial on (100) YSZ single-crystal substrates. The highest conductivity of the as-grown films is found at x = 0.12. The optical transmission window and absolute transparency of the films rivals or exceeds that of the most transparent conductive oxides known. Reductive annealing results in improved charge transport characteristics with little loss of optical transparency. No significant difference in electrical properties is observed between randomly oriented and heteroepitaxial films, thus arguing that carrier scattering effects at high-angle grain boundaries play a minor role in the film conductivity mechanism

Mirrorlike pulsed laser deposited tungsten thin film.

PubMed

Mostako, A T T; Rao, C V S; Khare, Alika

2011-01-01

Mirrorlike tungsten thin films on stainless steel substrate deposited via pulsed laser deposition technique in vacuum (10(-5) Torr) is reported, which may find direct application as first mirror in fusion devices. The crystal structure of tungsten film is analyzed using x-ray diffraction pattern, surface morphology of the tungsten films is studied with scanning electron microscope and atomic force microscope. The film composition is identified using energy dispersive x-ray. The specular and diffuse reflectivities with respect to stainless steel substrate of the tungsten films are recorded with FTIR spectra. The thickness and the optical quality of pulsed laser deposition deposited films are tested via interferometric technique. The reflectivity is approaching about that of the bulk for the tungsten film of thickness ∼782 nm.

Method for forming porous platinum films

DOEpatents

Maya, Leon

2000-01-01

A method for forming a platinum film includes providing a substrate, sputtering a crystalline platinum oxide layer over at least a portion of the substrate, and reducing the crystalline platinum oxide layer to form the platinum film. A device includes a non-conductive substrate and a platinum layer having a density of between about 2 and 5 g/cm.sup.3 formed over at least a portion of the non-conductive substrate. The platinum films produced in accordance with the present invention provide porous films suitable for use as electrodes, yet require few processing steps. Thus, such films are less costly. Such films may be formed on both conductive and non-conductive substrates. While the invention has been illustrated with platinum, other metals, such as noble metals, that form a low density oxide when reactively sputtered may also be used.

Soap films burst like flapping flags.

PubMed

Lhuissier, Henri; Villermaux, Emmanuel

2009-07-31

When punctured, a flat soap film bursts by opening a hole driven by liquid surface tension. The hole rim does not, however, remain smooth but soon develops indentations at the tip of which ligaments form, ultimately breaking and leaving the initially connex film into a mist of disjointed drops. We report on original observations showing that these indentations result from a flaglike instability between the film and the surrounding atmosphere inducing an oscillatory motion out of its plane. Just like a flag edge flaps in the wind, the film is successively accelerated on both sides perpendicularly to its plane, inducing film thickness modulations and centrifuging liquid ligaments that finally pinch off to form the observed spray. This effect exemplifies how the dynamics of fragile objects such as thin liquid films is sensitive to their embedding medium.

Carbon Nanotube Thin-Film Antennas.

PubMed

Puchades, Ivan; Rossi, Jamie E; Cress, Cory D; Naglich, Eric; Landi, Brian J

2016-08-17

Multiwalled carbon nanotube (MWCNT) and single-walled carbon nanotube (SWCNT) dipole antennas have been successfully designed, fabricated, and tested. Antennas of varying lengths were fabricated using flexible bulk MWCNT sheet material and evaluated to confirm the validity of a full-wave antenna design equation. The ∼20× improvement in electrical conductivity provided by chemically doped SWCNT thin films over MWCNT sheets presents an opportunity for the fabrication of thin-film antennas, leading to potentially simplified system integration and optical transparency. The resonance characteristics of a fabricated chlorosulfonic acid-doped SWCNT thin-film antenna demonstrate the feasibility of the technology and indicate that when the sheet resistance of the thin film is >40 ohm/sq no power is absorbed by the antenna and that a sheet resistance of <10 ohm/sq is needed to achieve a 10 dB return loss in the unbalanced antenna. The dependence of the return loss performance on the SWCNT sheet resistance is consistent with unbalanced metal, metal oxide, and other CNT-based thin-film antennas, and it provides a framework for which other thin-film antennas can be designed.

The Effect of Radiation on Selected Photographic Film

NASA Technical Reports Server (NTRS)

Slater, Richard; Kinard, John; Firsov, Ivan

2000-01-01

We conducted this film test to evaluate several manufacturers' photographic films for their ability to acquire imagery on the International Space Station. We selected 25 motion picture, photographic slide, and negative films from three different film manufacturers. We based this selection on the fact that their films ranked highest in other similar film tests, and on their general acceptance by the international community. This test differed from previous tests because the entire evaluation process leading up to the final selection was based on information derived after the original flight film was scanned to a digital file. Previously conducted tests were evaluated entirely based on 8 x 10s that were produced from the film either directly or through the internegative process. This new evaluation procedure provided accurate quantitative data on granularity and contrast from the digital data. This test did not try to define which film was best visually. This is too often based on personal preference. However, the test results did group the films by good, marginal, and unacceptable. We developed, and included in this report, a template containing quantitative, graphical, and visual information for each film. These templates should be sufficient for comparing the different films tested and subsequently selecting a film or films to be used for experiments and general documentation on the International Space Station.

Phthalate Esters in Indoor Window Films in a Northeastern Chinese Urban Center: Film Growth and Implications for Human Exposure.

PubMed

Huo, Chun-Yan; Liu, Li-Yan; Zhang, Zi-Feng; Ma, Wan-Li; Song, Wei-Wei; Li, Hai-Ling; Li, Wen-Long; Kannan, Kurunthachalam; Wu, Yong-Kai; Han, Ya-Meng; Peng, Zhi-Xiang; Li, Yi-Fan

2016-07-19

Indoor window film samples were collected in buildings during 2014-2015 for the determination of six phthalate diesters (PAEs). Linear regression analysis suggested that the film mass was positively and significantly correlated with the duration of film growth (from 7 to 77 days). PAEs were detected in all window film samples (n = 64). For all the samples with growth days ranged from 7 to 77 days, the median concentrations of total six PAEs (∑6PAEs) in winter and summer window film samples were 9900 ng/m(2) film (2000 μg/g film) and 4700 ng/m(2) film (650 μg/g film), respectively. Among PAEs analyzed, di-2-ethyl-hexyl phthalate (DEHP) was the major compound (71 ± 9.7%), followed by di-n-butyl phthalate (DBP; 20 ± 7.4%) and diisobutyl phthalate (DiBP; 5.1 ± 2.2%). Positive correlations among PAEs suggested their common sources in the window film samples. Room temperature and relative humidity were negatively and significantly correlated with PAEs concentations (in ng/m(2)). Poor ventilation in cold winter in Noreastern China significantly influenced the concentrations of PAEs in window film which suggested higher inhalation exposure dose in winter. The median hazard quotient (HQ) values from PAEs exposure were below 1, suggesting that the intake of PAEs via three exposure pathways was considered as acceptable.

A Comparison of the effectiveness of Mammographic Film-Screen and Standard Film-Screen in the Detection of Small Bone Fractures

PubMed Central

Sani, Karim Ghazikhanlou; Jafari, Mahmoodreza; Rostampoor, Nima

2011-01-01

The use of mammography film-screen is limited in general radiography. The purpose of this study was to compare the effectiveness of mammographic film-screen and standard film-screen systems in the detection of small bone fractures. Radiographs were taken from patients' extremities and neck areas using mammography film-screen and standard film-screen (n=57 each). Fourteen other radiographs were taken from other views (predominantly oblique views), making a total number of 128 radiographs. Paired radiographs, taken from the same areas, were compared by two radiologists in terms of image visual sharpness, presence of bony fractures, and soft tissue injuries. The surface dose received by patients in the two systems was also compared. The radiographs taken by mammography film-screen had a statistically better visual sharpness compared to those taken by the standard film-screen system. However, there was no statistically significant difference between the diagnostic accuracy of the two systems. Mammography film-screen was able to detect only one out of 57 lesions, whereas standard film-screen system did not detec any lesion. The surface dose received by patients in mammography film-screen was higher than that in standard film-screen system. The findings of the present study suggest that mammography film-screen may be recommended as a diagnostic tool for the detection of small fractures of tinny parts of body such as fingers, hand or foot. They also suggest that mammography film-screen has no advantage over standard film-screen for radiography of thick body parts such as neck and knee. PMID:23115417

Free-Standing, Flexible, Superomniphobic Films.

PubMed

Vahabi, Hamed; Wang, Wei; Movafaghi, Sanli; Kota, Arun K

2016-08-31

Fabrication of most superomniphobic surfaces requires complex process conditions or specialized and expensive equipment or skilled personnel. In order to circumvent these issues and make them end-user-friendly, we developed the free-standing, flexible, superomniphobic films. These films can be stored and delivered to the end-users, who can readily attach them to virtually any surface (even irregular shapes) and impart superomniphobicity. The hierarchical structure, the re-entrant texture, and the low solid surface energy render our films superomniphobic for a wide variety of liquids. We demonstrate that our free-standing, flexible, superomniphobic films have applications in enhanced chemical resistance and enhanced weight bearing.

The effects of film thickness on the electrical, optical, and structural properties of cylindrical, rotating, magnetron-sputtered ITO films

NASA Astrophysics Data System (ADS)

Kim, Jae-Ho; Seong, Tae-Yeon; Ahn, Kyung-Jun; Chung, Kwun-Bum; Seok, Hae-Jun; Seo, Hyeong-Jin; Kim, Han-Ki

2018-05-01

We report the characteristics of Sn-doped In2O3 (ITO) films intended for use as transparent conducting electrodes; the films were prepared via a five-generation, in-line type, cylindrical, rotating magnetron sputtering (CRMS) system as a function of film thickness. By using a rotating cylindrical ITO target with high usage (∼80%), we prepared high conductivity, transparent ITO films on five-generation size glass. The effects of film thickness on the electrical, optical, morphological, and structural properties of CRMS-grown ITO films are investigated in detail to correlate the thickness and performance of ITO films. The preferred orientation changed from the (2 2 2) to the (4 0 0) plane with increasing thickness of ITO is attributed to the stability of the (4 0 0) plane against resputtering during the CRMS process. Based on X-ray diffraction, surface field emission scanning electron microscopy, and cross-sectional transmission electron microscopy, we suggest a possible mechanism to explain the preferred orientation and effects of film thickness on the performance of CRMS-grown ITO films.

The Historian Encounters Film: A Historiography.

ERIC Educational Resources Information Center

Toplin, Robert Brent; Eudy, Jason

2002-01-01

Provides a historiography of the articles and books that focuses upon studying history through film. Reviews topics such as: censorship, the film industry's use and interpretations of history in films, and the lack of material on documentaries in the scholarship. (CMK)

Film thickness for different regimes of fluid-film lubrication. [elliptical contacts

NASA Technical Reports Server (NTRS)

Hamrock, B. J.; Dowson, D.

1983-01-01

Mathematical formulas are presented which express the dimensionless minimum film thickness for the four lubrication regimes found in elliptical contacts: isoviscous-rigid regime; piezoviscous-rigid regime; isoviscous-elastic regime; and piezoviscous-elastic regime. The relative importance of pressure on elastic distortion and lubricant viscosity is the factor that distinguishes these regimes for a given conjunction geometry. In addition, these equations were used to develop maps of the lubrication regimes by plotting film thickness contours on a log-log grid of the dimensionless viscosity and elasticity parameters for three values of the ellipticity parameter. These results present a complete theoretical film thickness parameter solution for elliptical constants in the four lubrication regimes. The results are particularly useful in initial investigations of many practical lubrication problems involving elliptical conjunctions.

Rare earth-based low-index films for IR and multispectral thin film solutions

NASA Astrophysics Data System (ADS)

Stolze, Markus; Neff, Joe; Waibel, Friedrich

2017-10-01

Non-thoriated rare-earth fluoride based coating solutions involving DyF3 and YbF3 based films as well as non-wetting fluorohydrocarbon cap layers on such films, have been deposited, analyzed and partly optimized. Intermediate results for DyF3 based films from ion assisted e-gun deposition with O2 and N2 alone and as base for the non-wetting to-player as well as for YbF3 starting material with or without admixtures of CaF2 are discussed for low-loss LWIR and multispectral solutions.

Real-Time Deposition Monitor for Ultrathin Conductive Films

NASA Technical Reports Server (NTRS)

Hines, Jacqueline

2011-01-01

A device has been developed that can be used for the real-time monitoring of ultrathin (2 or more) conductive films. The device responds in less than two microseconds, and can be used to monitor film depositions up to about 60 thick. Actual thickness monitoring capability will vary based on properties of the film being deposited. This is a single-use device, which, due to the very low device cost, can be disposable. Conventional quartz/crystal microbalance devices have proven inadequate to monitor the thickness of Pd films during deposition of ultrathin films for hydrogen sensor devices. When the deposited film is less than 100 , the QCM measurements are inadequate to allow monitoring of the ultrathin films being developed. Thus, an improved, high-sensitivity, real-time deposition monitor was needed to continue Pd film deposition development. The new deposition monitor utilizes a surface acoustic wave (SAW) device in a differential delay-line configuration to produce both a reference response and a response for the portion of the device on which the film is being deposited. Both responses are monitored simultaneously during deposition. The reference response remains unchanged, while the attenuation of the sensing path (where the film is being deposited) varies as the film thickness increases. This device utilizes the fact that on high-coupling piezoelectric substrates, the attenuation of an SAW undergoes a transition from low to very high, and back to low as the conductivity of a film on the device surface goes from nonconductive to highly conductive. Thus, the sensing path response starts with a low insertion loss, and as a conductive film is deposited, the film conductivity increases, causing the device insertion loss to increase dramatically (by up to 80 dB or more), and then with continued film thickness increases (and the corresponding conductivity increases), the device insertion loss goes back down to the low level at which it started. This provides a