Integrated chassis control of active front steering and yaw stability control based on improved inverse nyquist array method.

PubMed

Zhu, Bing; Chen, Yizhou; Zhao, Jian

2014-01-01

An integrated chassis control (ICC) system with active front steering (AFS) and yaw stability control (YSC) is introduced in this paper. The proposed ICC algorithm uses the improved Inverse Nyquist Array (INA) method based on a 2-degree-of-freedom (DOF) planar vehicle reference model to decouple the plant dynamics under different frequency bands, and the change of velocity and cornering stiffness were considered to calculate the analytical solution in the precompensator design so that the INA based algorithm runs well and fast on the nonlinear vehicle system. The stability of the system is guaranteed by dynamic compensator together with a proposed PI feedback controller. After the response analysis of the system on frequency domain and time domain, simulations under step steering maneuver were carried out using a 2-DOF vehicle model and a 14-DOF vehicle model by Matlab/Simulink. The results show that the system is decoupled and the vehicle handling and stability performance are significantly improved by the proposed method.

Asymptotic sideslip angle and yaw rate decoupling control in four-wheel steering vehicles

NASA Astrophysics Data System (ADS)

Marino, Riccardo; Scalzi, Stefano

2010-09-01

This paper shows that, for a four-wheel steering vehicle, a proportional-integral (PI) active front steering control and a PI active rear steering control from the yaw rate error together with an additive feedforward reference signal for the vehicle sideslip angle can asymptotically decouple the lateral velocity and the yaw rate dynamics; that is the control can set arbitrary steady state values for lateral speed and yaw rate at any longitudinal speed. Moreover, the PI controls can suppress oscillatory behaviours by assigning real stable eigenvalues to a widely used linearised model of the vehicle steering dynamics for any value of longitudinal speed in understeering vehicles. In particular, the four PI control parameters are explicitly expressed in terms of the three real eigenvalues to be assigned. No lateral acceleration and no lateral speed measurements are required. The controlled system maintains the well-known advantages of both front and rear active steering controls: higher controllability, enlarged bandwidth for the yaw rate dynamics, suppressed resonances, new stable cornering manoeuvres and improved manoeuvrability. In particular, zero lateral speed may be asymptotically achieved while controlling the yaw rate: in this case comfort is improved since the phase lag between lateral acceleration and yaw rate is reduced. Also zero yaw rate can be asymptotically achieved: in this case additional stable manoeuvres are obtained in obstacle avoidance. Several simulations, including step references and moose tests, are carried out on a standard small SUV CarSim model to explore the robustness with respect to unmodelled effects such as combined lateral and longitudinal tyre forces, pitch, roll and driver dynamics. The simulations confirm the decoupling between the lateral velocity and the yaw rate and show the advantages obtained by the proposed control: reduced lateral speed or reduced yaw rate, suppressed oscillations and new stable manoeuvres.

Improved LTVMPC design for steering control of autonomous vehicle

NASA Astrophysics Data System (ADS)

Velhal, Shridhar; Thomas, Susy

2017-01-01

An improved linear time varying model predictive control for steering control of autonomous vehicle running on slippery road is presented. Control strategy is designed such that the vehicle will follow the predefined trajectory with highest possible entry speed. In linear time varying model predictive control, nonlinear vehicle model is successively linearized at each sampling instant. This linear time varying model is used to design MPC which will predict the future horizon. By incorporating predicted input horizon in each successive linearization the effectiveness of controller has been improved. The tracking performance using steering with front wheel and braking at four wheels are presented to illustrate the effectiveness of the proposed method.

Analysis of Motorcycle Weave Mode by using Energy Flow Method

NASA Astrophysics Data System (ADS)

Marumo, Yoshitaka; Katayama, Tsuyoshi

The activation mechanism of motorcycle weave mode is clarified within the framework of the energy flow method, which calculates energy flow of mechanical forces in each motion. It is demonstrated that only a few mechanical forces affect the stability of the weave mode from among a total of about 40 mechanical forces. The activation of the lateral, yawing and rolling motions destabilize the weave mode, while activation of the steering motion stabilizes the weave mode. A detailed investigation of the energy flow of the steering motion reveals that the steering motion plays an important role in clarifying the characteristics of the weave mode. As activation of the steering motion progresses the phase of the front tire side force, and the weave mode is consequently stabilized. This paper provides a design guide for stabilizing the weave mode and the wobble mode compatibility.

Path-following in model predictive rollover prevention using front steering and braking

NASA Astrophysics Data System (ADS)

Ghazali, Mohammad; Durali, Mohammad; Salarieh, Hassan

2017-01-01

In this paper vehicle path-following in the presence of rollover risk is investigated. Vehicles with high centre of mass are prone to roll instability. Untripped rollover risk is increased in high centre of gravity vehicles and high-friction road condition. Researches introduce strategies to handle the short-duration rollover condition. In these researches, however, trajectory tracking is affected and not thoroughly investigated. This paper puts stress on tracking error from rollover prevention. A lower level model predictive front steering controller is adopted to deal with rollover and tracking error as a priority sequence. A brake control is included in lower level controller which directly obeys an upper level controller (ULC) command. The ULC manages vehicle speed regarding primarily tracking error. Simulation results show that the proposed control framework maintains roll stability while tracking error is confined to predefined error limit.

Static load simulation of steering knuckle for a formula student race car

NASA Astrophysics Data System (ADS)

Saputro, Bagus Aulia; Ubaidillah, Triono, Dicky Agus; Pratama, Dzaky Roja; Cahyono, Sukmaji Indro; Imaduddin, Fitrian

2018-02-01

This research aims to determine the stress distribution which occurs on the steering knuckle and to define its safety factor number. Steering knuckle is the most critical part of a car's steering system. Steering knuckle supports the tie rod, brake caliper, and the wheels to provide stability. Steering knuckle withstands the load which given on the front wheels and functions as the wheel's axis. Balljoint and king support the rotation of the suspension arm. When the car is in idle position, knuckle hold the weight of the car, it gets braking force when it's braking and cornering. Knuckle is designed to have the strength that could withstand load and to have a good safety factor value. Knuckle is designed using Fusion software then simulated using Fusion simulation software with a static load, moment braking force, and cornering force as the loads in this simulation. The simulation works in ideal condition. The result of this simulation is satisfying. This simulation produces a maximum displacement of 0.01281mm, the maximum shear stress is 3.707 MPa on the stub hole, and the safety factor is 5.24. The material used for this product is mild steel AISI 1018.

Designation and verification of road markings detection and guidance method

NASA Astrophysics Data System (ADS)

Wang, Runze; Jian, Yabin; Li, Xiyuan; Shang, Yonghong; Wang, Jing; Zhang, JingChuan

2018-01-01

With the rapid development of China's space industry, digitization and intelligent is the tendency of the future. This report is present a foundation research about guidance system which based on the HSV color space. With the help of these research which will help to design the automatic navigation and parking system for the frock transport car and the infrared lamp homogeneity intelligent test equipment. The drive mode, steer mode as well as the navigation method was selected. In consideration of the practicability, it was determined to use the front-wheel-steering chassis. The steering mechanism was controlled by the stepping motors, and it is guided by Machine Vision. The optimization and calibration of the steering mechanism was made. A mathematical model was built and the objective functions was constructed for the steering mechanism. The extraction method of the steering line was studied and the motion controller was designed and optimized. The theory of HSV, RGB color space and analysis of the testing result will be discussed Using the function library OPENCV on the Linux system to fulfill the camera calibration. Based on the HSV color space to design the guidance algorithm.

An Attempt to Identify Indicators of Competence on Mechanical Maintenance Tasks.

DTIC Science & Technology

1979-01-01

them on the DA Form 2404. The vehicle is prepared as follows: 1. Left front wheel and drum removed. 2. Retracting spring disconnected. 3. Brake pedal...charging system. 8 2. Troubleshoot starting system circuit on Ml51Al/A2 truck. ii 3. Replace steering linkage on Ml5lAl/A2 truck. 8 4. Troubleshoot brakes ...Troubleshoot starting system circuit on MI51AI/A2 truck. 101 3. Replace steering linkage on MI51AI/A2 truck. 96 4. Troubleshoot brakes and controls

49 CFR 661.11 - Rolling stock procurements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Devices; (21) Car Axle Counters; (22) Communication Based Train Control (CBTC). (u) Communication... components of a bus. This list is not all-inclusive. Car body shells, egines, transmissions, front axle... assemblies, air compressor and pneumatic systems, generator/alternator and electrical systems, steering...

49 CFR 661.11 - Rolling stock procurements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Devices; (21) Car Axle Counters; (22) Communication Based Train Control (CBTC). (u) Communication... components of a bus. This list is not all-inclusive. Car body shells, egines, transmissions, front axle... assemblies, air compressor and pneumatic systems, generator/alternator and electrical systems, steering...

Intelligent vehicle safety control strategy in various driving situations

NASA Astrophysics Data System (ADS)

Moon, Seungwuk; Cho, Wanki; Yi, Kyongsu

2010-12-01

This paper describes a safety control strategy for intelligent vehicles with the objective of optimally coordinating the throttle, brake, and active front steering actuator inputs to obtain both lateral stability and longitudinal safety. The control system consists of a supervisor, control algorithms, and a coordinator. From the measurement and estimation signals, the supervisor determines the active control modes among normal driving, longitudinal safety, lateral stability, and integrated safety control mode. The control algorithms consist of longitudinal and lateral stability controllers. The longitudinal controller is designed to improve the driver's comfort during normal, safe-driving situations, and to avoid rear-end collision in vehicle-following situations. The lateral stability controller is designed to obtain the required manoeuvrability and to limit the vehicle body's side-slip angle. To obtain both longitudinal safety and lateral stability control in various driving situations, the coordinator optimally determines the throttle, brake, and active front steering inputs based on the current status of the subject vehicle. Closed-loop simulations with the driver-vehicle-controller system are conducted to investigate the performance of the proposed control strategy. From these simulation results, it is shown that the proposed control algorithm assists the driver in combined severe braking/large steering manoeuvring so that the driver can maintain good manoeuvrability and prevent the vehicle from crashing in vehicle-following situations.

Driver steering dynamics measured in car simulator under a range of visibility and roadmaking conditions

NASA Technical Reports Server (NTRS)

Allen, R. W.; Mcruer, D. T.

1977-01-01

A simulation experiment was conducted to determine the effect of reduced visibility on driver lateral (steering) control. The simulator included a real car cab and a single lane road image projected on a screen six feet in front of the driver. Simulated equations of motion controlled apparent car lane position in response to driver steering actions, wind gusts, and road curvature. Six drivers experienced a range of visibility conditions at various speeds with assorted roadmaking configurations (mark and gap lengths). Driver describing functions were measured and detailed parametric model fits were determined. A pursuit model employing a road curvature feedforward was very effective in explaining driver behavior in following randomly curving roads. Sampled-data concepts were also effective in explaining the combined effects of reduced visibility and intermittent road markings on the driver's dynamic time delay. The results indicate the relative importance of various perceptual variables as the visual input to the driver's steering control process is changed.

Generalized internal model robust control for active front steering intervention

NASA Astrophysics Data System (ADS)

Wu, Jian; Zhao, Youqun; Ji, Xuewu; Liu, Yahui; Zhang, Lipeng

2015-03-01

Because of the tire nonlinearity and vehicle's parameters' uncertainties, robust control methods based on the worst cases, such as H ∞, µ synthesis, have been widely used in active front steering control, however, in order to guarantee the stability of active front steering system (AFS) controller, the robust control is at the cost of performance so that the robust controller is a little conservative and has low performance for AFS control. In this paper, a generalized internal model robust control (GIMC) that can overcome the contradiction between performance and stability is used in the AFS control. In GIMC, the Youla parameterization is used in an improved way. And GIMC controller includes two sections: a high performance controller designed for the nominal vehicle model and a robust controller compensating the vehicle parameters' uncertainties and some external disturbances. Simulations of double lane change (DLC) maneuver and that of braking on split- µ road are conducted to compare the performance and stability of the GIMC control, the nominal performance PID controller and the H ∞ controller. Simulation results show that the high nominal performance PID controller will be unstable under some extreme situations because of large vehicle's parameters variations, H ∞ controller is conservative so that the performance is a little low, and only the GIMC controller overcomes the contradiction between performance and robustness, which can both ensure the stability of the AFS controller and guarantee the high performance of the AFS controller. Therefore, the GIMC method proposed for AFS can overcome some disadvantages of control methods used by current AFS system, that is, can solve the instability of PID or LQP control methods and the low performance of the standard H ∞ controller.

Proposal to use vibration analysis steering components and car body to monitor, for example, the state of unbalance wheel

NASA Astrophysics Data System (ADS)

Janczur, R.

2016-09-01

The results of road tests of car VW Passat equipped with tires of size 195/65 R15, on the influence of the unbalancing front wheel on vibration of the parts of steering system, steering wheel and the body of the vehicle have been presented in this paper. Unbalances wheels made using weights of different masses, placed close to the outer edge of the steel rim and checked on the machine Hunter GSP 9700 for balancing wheels. The recorded waveforms vibration steering components and car body, at different constant driving speeds, subjected to spectral analysis to determine the possibility of isolating vibration caused by unbalanced wheel in various states and coming from good quality asphalt road surface. The results were discussed in terms of the possibility of identifying the state of unbalancing wheels and possible changes in radial stiffness of the tire vibration transmitted through the system driving wheel on the steering wheel. Vibration analysis steering components and car body, also in the longitudinal direction, including information from the CAN bus of the state of motion of the car, can be used to monitor the development of the state of unbalance wheel, tire damage or errors shape of brake discs or brake drums, causing pulsations braking forces.

Enhanced betatron radiation by steering a laser-driven plasma wakefield with a tilted shock front

NASA Astrophysics Data System (ADS)

Yu, Changhai; Liu, Jiansheng; Wang, Wentao; Li, Wentao; Qi, Rong; Zhang, Zhijun; Qin, Zhiyong; Liu, Jiaqi; Fang, Ming; Feng, Ke; Wu, Ying; Ke, Lintong; Chen, Yu; Wang, Cheng; Xu, Yi; Leng, Yuxin; Xia, Changquan; Li, Ruxin; Xu, Zhizhan

2018-03-01

We have experimentally realized a scheme to enhance betatron radiation by manipulating transverse oscillation of electrons in a laser-driven plasma wakefield with a tilted shock front (TSF). Very brilliant betatron x-rays have been produced with significant enhancement both in photon yield and peak energy but almost maintain the e-beam energy spread and charge. Particle-in-cell simulations indicate that the accelerated electron beam (e beam) can acquire a very large transverse oscillation amplitude with an increase in more than 10-fold, after being steered into the deflected wakefield due to the refraction of the driving laser at the TSF. Spectral broadening of betatron radiation can be suppressed owing to the small variation in the peak energy of the low-energy-spread e beam in a plasma wiggler regime. It is demonstrated that the e-beam generation, refracting, and wiggling can act as a whole to realize the concurrence of monoenergetic e beams and bright x-rays in a compact laser-wakefield accelerator.

Pulse Front Tilt and Laser Plasma Acceleration

NASA Astrophysics Data System (ADS)

Mittelberger, Daniel; Thévenet, Maxence; Nakamura, Kei; Lehe, Remi; Gonsalves, Anthony; Benedetti, Carlo; Leemans, Wim

2017-10-01

Pulse front tilt (PFT) is potentially present in any CPA laser system, but its effects may be overlooked because spatiotemporal pulse characterization is considerably more involved than measuring only spatial or temporal profile. PFT is particularly important for laser plasma accelerators (LPA) because it influences electron beam injection and steering. In this work, experimental results from the BELLA Center will be presented that demonstrate the effect of optical grating misalignment and optical compression, resulting in PFT, on accelerator performance. Theoretical models of laser and electron beam steering will be introduced based on particle-in-cell simulations showing distortion of the plasma wake. Theoretical predictions will be compared with experiments and complimentary simulations, and tolerances on PFT and optical compressor alignment will be developed as a function of LPA performance requirements. This work was supported by the Office of High Energy Physics, Office of Science, US Department of Energy under Contract DE-AC02-05CH11231 and the National Science Foundation under Grant PHY-1415596.

Formation of Epichlorohydrin, a Known Rodent Carcinogen, Following Oral Administration of 1,3-Dichloro-2-propanol in Rats

PubMed Central

2015-01-01

The observed toxicity and carcinogenicity of 1,3-dichloro-2-propanol (DCP) in rodents is thought to be due to the formation of reactive metabolites, epichlorohydrin (ECH) and dichloroacetone (DCA). However, there is no direct evidence for the formation of these metabolites from exposure to DCP in rodents due to the challenges of measuring these reactive intermediates directly in vivo. The objective of this work was to investigate the metabolism of DCP to ECH and DCA in vivo by first developing a sensitive analytical method in a suitable biological matrix and analyzing samples from rats administered DCP. DCA reacted rapidly in vitro in rat blood, plasma, and liver homogenate, precluding its detection. Because ECH rapidly disappeared in liver homogenate, but was relatively long-lived in plasma and blood in vitro, blood was selected for analysis of this metabolite. Following a single oral dose of 50 mg/kg DCP in male or female Harlan Sprague–Dawley rats, ECH was detected in blood with a maximum concentration reached at ≤13.7 min. ECH was cleared rapidly with a half-life of ca. 33 and 48 min in males and females, respectively. Following a single oral dose of 25 mg/kg ECH in male and female rats, the elimination half-life of ECH was ca. 34 and 20 min, respectively; the oral bioavailability of ECH was low (males, 5.2%; females, 2.1%), suggesting extensive first pass metabolism of ECH following oral administration. The area under the concentration vs time curve for ECH following oral administration of DCP and intravenous administration of ECH was used to estimate the percent of the DCP dose converted to ECH in rats. On the basis of this analysis, we concluded that in male and female rats following oral administration of 50 mg/kg DCP, ≥1.26% or ≥1.78% of the administered dose was metabolized to ECH, respectively. PMID:25254956

Snowmobile Repair. Teacher Edition.

ERIC Educational Resources Information Center

Hennessy, Stephen S.; Conrad, Rex

This teacher's guide contains 14 units on snowmobile repair: (1) introduction to snowmobile repair; (2) skis, front suspension, and steering; (3) drive clutch; (4) drive belts; (5) driven clutch; (6) chain drives; (7) jackshafts and axles; (8) rear suspension; (9) tracks; (10) shock absorbers; (11) brakes; (12) engines; (13) ignition and…

Intervention criterion and control research for active front steering with consideration of road adhesion

NASA Astrophysics Data System (ADS)

Wu, Xiaojian; Zhou, Bing; Wen, Guilin; Long, Lefei; Cui, Qingjia

2018-04-01

A multi-objective active front steering (AFS) control system considering the road adhesion constraint on vehicle stability is developed using the sliding mode control (SMC) method. First, an identification function combined with the relationship between the yaw rate and the steering angle is developed to determine whether the tyre state is linear or nonlinear. On this basis, an intervention criterion for the AFS system is proposed to improve vehicle handling and stability in emergent conditions. A sideslip angle stability domain enveloped by the upper, lower, left, and right boundaries, as well as the constraint of road adhesion coefficient, is constructed based on the ? phase-plane method. A dynamic weighting coefficient to coordinate the control of yaw rate and sideslip angle, and a control strategy that considers changing control objectives based on the desired yaw rate, the desired sideslip angle, and their proportional weights, are proposed for the SMC controller. Because road adhesion has a significant effect on vehicle stability and to meet the control algorithm's requirement of real-time access to vehicle states, a unscented Kalman filter-based state observer is proposed to estimate the adhesion coefficient and the required states. Finally, simulations are performed using high and low road adhesion conditions in a Matlab/Simulink environment, and the results show that the proposed AFS control system promptly intervenes according to the intervention criterion, effectively improving vehicle handling and stability.

ECHS1 mutations cause combined respiratory chain deficiency resulting in Leigh syndrome.

PubMed

Sakai, Chika; Yamaguchi, Seiji; Sasaki, Masayuki; Miyamoto, Yusaku; Matsushima, Yuichi; Goto, Yu-ichi

2015-02-01

The human ECHS1 gene encodes the short-chain enoyl coenzyme A hydratase, the enzyme that catalyzes the second step of β-oxidation of fatty acids in the mitochondrial matrix. We report on a boy with ECHS1 deficiency who was diagnosed with Leigh syndrome at 21 months of age. The patient presented with hypotonia, metabolic acidosis, and developmental delay. A combined respiratory chain deficiency was also observed. Targeted exome sequencing of 776 mitochondria-associated genes encoded by nuclear DNA identified compound heterozygous mutations in ECHS1. ECHS1 protein expression was severely depleted in the patient's skeletal muscle and patient-derived myoblasts; a marked decrease in enzyme activity was also evident in patient-derived myoblasts. Immortalized patient-derived myoblasts that expressed exogenous wild-type ECHS1 exhibited the recovery of the ECHS1 activity, indicating that the gene defect was pathogenic. Mitochondrial respiratory complex activity was also mostly restored in these cells, suggesting that there was an unidentified link between deficiency of ECHS1 and respiratory chain. Here, we describe the patient with ECHS1 deficiency; these findings will advance our understanding not only the pathology of mitochondrial fatty acid β-oxidation disorders, but also the regulation of mitochondrial metabolism. © 2014 WILEY PERIODICALS, INC.

Progress on ITER Diagnostic Integration

NASA Astrophysics Data System (ADS)

Johnson, David; Feder, Russ; Klabacha, Jonathan; Loesser, Doug; Messineo, Mike; Stratton, Brentley; Wood, Rick; Zhai, Yuhu; Andrew, Phillip; Barnsley, Robin; Bertschinger, Guenter; Debock, Maarten; Reichle, Roger; Udintsev, Victor; Vayakis, George; Watts, Christopher; Walsh, Michael

2013-10-01

On ITER, front-end components must operate reliably in a hostile environment. Many will be housed in massive port plugs, which also shield the machine from radiation. Multiple diagnostics reside in a single plug, presenting new challenges for developers. Front-end components must tolerate thermally-induced stresses, disruption-induced mechanical loads, stray ECH radiation, displacement damage, and degradation due to plasma-induced coatings. The impact of failures is amplified due to the difficulty in performing robotic maintenance on these large structures. Motivated by needs to minimize disruption loads on the plugs, standardize the handling of shield modules, and decouple the parallel efforts of the many parties, the packaging strategy for diagnostics has recently focused on the use of 3 vertical shield modules inserted from the plasma side into each equatorial plug structure. At the front of each is a detachable first wall element with customized apertures. Progress on US equatorial and upper plugs will be used as examples, including the layout of components in the interspace and port cell regions. Supported by PPPL under contract DE-AC02-09CH11466 and UT-Battelle, LLC under contract DE-AC05-00OR22725 with the U.S. DOE.

Optimized coordination of brakes and active steering for a 4WS passenger car.

PubMed

Tavasoli, Ali; Naraghi, Mahyar; Shakeri, Heman

2012-09-01

Optimum coordination of individual brakes and front/rear steering subsystems is presented. The integrated control strategy consists of three modules. A coordinated high-level control determines the body forces/moment required to achieve vehicle motion objectives. The body forces/moment are allocated to braking and steering subsystems through an intermediate unit, which integrates available subsystems based on phase plane notion in an optimal manner. To this end, an optimization problem including several equality and inequality constraints is defined and solved analytically, such that a real-time implementation can be realized without the use of numeric optimization software. A low-level slip-ratio controller works to generate the desired longitudinal forces at small longitudinal slip-ratios, while averting wheel locking at large slip-ratios. The efficiency of the suggested approach is demonstrated through computer simulations. Copyright © 2012 ISA. Published by Elsevier Ltd. All rights reserved.

A Novel Atypical PKC-Iota Inhibitor, Echinochrome A, Enhances Cardiomyocyte Differentiation from Mouse Embryonic Stem Cells.

PubMed

Kim, Hyoung Kyu; Cho, Sung Woo; Heo, Hye Jin; Jeong, Seung Hun; Kim, Min; Ko, Kyung Soo; Rhee, Byoung Doo; Mishchenko, Natalia P; Vasileva, Elena A; Fedoreyev, Sergey A; Stonik, Valentin A; Han, Jin

2018-06-02

Echinochrome A (EchA) is a marine bioproduct extracted from sea urchins having antioxidant, antimicrobial, anti-inflammatory, and chelating effects, and is the active component of the clinical drug histochrome. We investigated the potential use of Ech A for inducing cardiomyocyte differentiation from mouse embryonic stem cells (mESCs). We also assessed the effects of Ech A on mitochondrial mass, inner membrane potential (Δψm), reactive oxygen species generation, and levels of Ca 2+ . To identify the direct target of Ech A, we performed in vitro kinase activity and surface plasmon resonance binding assays. Ech A dose-dependently enhanced cardiomyocyte differentiation with higher beating rates. Ech A (50 μM) increased the mitochondrial mass and membrane potential but did not alter the mitochondrial superoxide and Ca 2+ levels. The in vitro kinase activity of the atypical protein kinase C-iota (PKCι) was significantly decreased by 50 μM of Ech A with an IC 50 for PKCι activity of 107 μM. Computational protein-ligand docking simulation results suggested the direct binding of Ech A to PKCι, and surface plasmon resonance confirmed the direct binding with a low K D of 6.3 nM. Therefore, Ech A is a potential drug for enhancing cardiomyocyte differentiation from mESCs through direct binding to PKCι and inhibition of its activity.

DIII-D Electron Cyclotron Heating System Status and Upgrades

DOE PAGES

Cengher, Mirela; Lohr, John; Gorelov, Yuri; ...

2016-06-23

The DIII-D Electron Cyclotron Heating (ECH) system consists of six 110 GHz gyrotrons with corrugated coaxial 31.75 mm waveguide transmission lines and steerable launching mirrors. The system has been gradually updated, leading to increased experimental flexibility and a high system reliability of 91% in the past year. Operationally, the gyrotrons can generate up to a total of 4.8 MW of rf power for pulses up to 5 seconds. The maximum ECH energy injected into the DIII-D is 16.6 MJ. The HE1,1 mode content is over 85% for all the lines, and the transmission coefficient is better than -1.1 dB formore » all the transmission lines, close to the theoretical value. A new depressed collector gyrotron was recently installed and was injecting up to 640 kW of power into the plasma during 2014-2015 tokamak operations. Four dual waveguide launchers, which can steer the RF beams ±20 degrees poloidally and toroidally, are used for real-time neoclassical tearing mode control and suppression. The launchers now have increased poloidal scanning speed and beam positioning accuracy of ~±2 mm at the plasma center. Two more gyrotrons are expected to be installed and operational in 2015- 2016. The first is a repaired 110 GHz, 1 MW gyrotron that had a gun failure after more than 11 years of operation at DIII-D. The second is a newly designed depressed collector tube in the 1.5 MW class, operating at 117.5 GHz, manufactured by Communications and Power Industries (CPI).« less

Effects of Structural Flexibility on Motorcycle Straight Running Stability by using Energy Flow Method

NASA Astrophysics Data System (ADS)

Marumo, Yoshitaka; Katayama, Tsuyoshi

This study uses the energy flow method to analyze how structural flexibility affects the motorcycle wobble and weave modes. Lateral bending of the front fork and torsion of the main frame affect the wobble mode stability. These are based on the gyroscopic effect of the front wheel in the steering motion by considering structural flexibility. At high speeds, lateral bending of the front fork and torsion of the rear swing arm more significantly affect the weave mode stability. These are primarily due to the phase changes of the external force generated by the yaw rate in the lateral motion. The phase change of the yaw rate force in the lateral motion originates from the phase change of the tire side forces.

Chassis integrated control for active suspension, active front steering and direct yaw moment systems using hierarchical strategy

NASA Astrophysics Data System (ADS)

Zhao, Jing; Wong, Pak Kin; Ma, Xinbo; Xie, Zhengchao

2017-01-01

This paper proposes a novel integrated controller with three-layer hierarchical structure to coordinate the interactions among active suspension system (ASS), active front steering (AFS) and direct yaw moment control (DYC). First of all, a 14-degree-of-freedom nonlinear vehicle dynamic model is constructed. Then, an upper layer is designed to calculate the total corrected moment for ASS and intermediate layer based on linear moment distribution. By considering the working regions of the AFS and DYC, the intermediate layer is functionalised to determine the trigger signal for the lower layer with corresponding weights. The lower layer is utilised to separately trace the desired value of each local controller and achieve the local control objectives of each subsystem. Simulation results show that the proposed three-layer hierarchical structure is effective in handling the working region of the AFS and DYC, while the quasi-experimental result shows that the proposed integrated controller is able to improve the lateral and vertical dynamics of the vehicle effectively as compared with a conventional electronic stability controller.

Land-falling typhoons are controlled by the meridional oscillation of the Kuroshio Extension

NASA Astrophysics Data System (ADS)

Huang, Shihming; Oey, Lie-Yauw

2018-06-01

Low-frequency variations of typhoon paths are often attributed to changes in the North Pacific subtropical high and monsoon through influences on the steering wind. Evidence indicates however a strong imprint of the Kuroshio on the atmosphere. Here we show that the meridional oscillation of sea surface temperature (SST) front over the Kuroshio Extension east of Japan significantly correlates with the number of land-falling typhoons along East Asia from June to October, accounting for 70% of the low-frequency variance since 1980. We used observations and a simple model to show that when the SST front shifts poleward (equatorward), SST gradient south of the current and westerly tropospheric wind weaken (strengthen), steering more typhoons to veer toward (away from) the East Asian continent. Our analysis also indicates that long-term weakening of SST gradient and westerly wind appears to be concomitant with poleward shifting of the Kuroshio, attributed to global warming in some studies, and suggests the potential for more land-falling typhoons in East Asia in the coming decades.

Echinacea purpurea (L.) Moench modulates human T-cell cytokine response☆

PubMed Central

Fonseca, Fabiana N.; Papanicolaou, Genovefa; Lin, Hong; Lau, Clara B.S.; Kennelly, Edward J.; Cassileth, Barrie R.; Cunningham-Rundles, Susanna

2014-01-01

The study objective was to evaluate the composition of a neutral and weakly acidic water-soluble extract from Echinacea purpurea (L.) Moench (EchNWA) previously shown to modify murine influenza infection, and to assess immunomodulatory effects on human T-cells. EchNWA extract from fresh aerial parts was extracted with water, ethanolic precipitation, and size-exclusion chromatography. The chemical profile of EchNWA was characterized by chromatography (size-exclusion, HPLC, GC–MS), and small molecule finger-print analysis performed by HPLC–PDA. Jurkat T-cells at high and low cell density were pretreated or not with doses of EchNWA, followed by activation with phorbol 12-myristate 13-acetate plus ionomycin (PMA+I). Interleukin-2 (IL-2) and interferon gamma (IFNg) cytokine secretions were measured by multi-cytokine luminex technology. Results showed that EchNWA contains 80% polysaccharides, predominantly a 10 kDa entity; phenolic compounds, cynarin, cichoric and caftaric acids, but no detectable alkylamides. Cytokine production required stimulation and was lower after PMA+I activation in high-density compared to low-density conditions. EchNWA mediated a strong dose-dependent enhancement of high-density T-cell production of IL-2 and IFNg response to PMA+I. EchNWA alone did not stimulate T-cells. EchNWA enhanced mean fluorescence intensity of IL-2 in Jurkat T-cells activated by PMA+1 or ionomycin alone. Conversely EchNWA mediated modest but significant suppression of IFNg response and reduced the percentage of CD25+ T-cells under low-density conditions. Conclusions are that EchNWA polysaccharides, but not phenolic compounds have dose-related adjuvant effects on human T-cell cytokine responses characterized by enhancing and suppressive effects that are regulated by T-cell density. PMID:24434371

A 1.2-V CMOS front-end for LTE direct conversion SAW-less receiver

NASA Astrophysics Data System (ADS)

Riyan, Wang; Jiwei, Huang; Zhengping, Li; Weifeng, Zhang; Longyue, Zeng

2012-03-01

A CMOS RF front-end for the long-term evolution (LTE) direct conversion receiver is presented. With a low noise transconductance amplifier (LNA), current commutating passive mixer and transimpedance operational amplifier (TIA), the RF front-end structure enables high-integration, high linearity and simple frequency planning for LTE multi-band applications. Large variable gain is achieved using current-steering transconductance stages. A current commutating passive mixer with 25% duty-cycle LO improves gain, noise and linearity. A direct coupled current-input filter (DCF) is employed to suppress the out-of-band interferer. Fabricated in a 0.13-μm CMOS process, the RF front-end achieves a 45 dB conversion voltage gain, 2.7 dB NF, -7 dBm IIP3, and +60 dBm IIP2 with calibration from 2.3 to 2.7 GHz. The total RF front end with divider draws 40 mA from a single 1.2-V supply.

ECHS1 mutations in Leigh disease: a new inborn error of metabolism affecting valine metabolism.

PubMed

Peters, Heidi; Buck, Nicole; Wanders, Ronald; Ruiter, Jos; Waterham, Hans; Koster, Janet; Yaplito-Lee, Joy; Ferdinandusse, Sacha; Pitt, James

2014-11-01

Two siblings with fatal Leigh disease had increased excretion of S-(2-carboxypropyl)cysteine and several other metabolites that are features of 3-hydroxyisobutyryl-CoA hydrolase (HIBCH) deficiency, a rare defect in the valine catabolic pathway associated with Leigh-like disease. However, this diagnosis was excluded by HIBCH sequencing and normal enzyme activity. In contrast to HIBCH deficiency, the excretion of 3-hydroxyisobutyryl-carnitine was normal in the children, suggesting deficiency of short-chain enoyl-CoA hydratase (ECHS1 gene). This mitochondrial enzyme is active in several metabolic pathways involving fatty acids and amino acids, including valine, and is immediately upstream of HIBCH in the valine pathway. Both children were compound heterozygous for a c.473C > A (p.A158D) missense mutation and a c.414+3G>C splicing mutation in ECHS1. ECHS1 activity was markedly decreased in cultured fibroblasts from both siblings, ECHS1 protein was undetectable by immunoblot analysis and transfection of patient cells with wild-type ECHS1 rescued ECHS1 activity. The highly reactive metabolites methacrylyl-CoA and acryloyl-CoA accumulate in deficiencies of both ECHS1 and HIBCH and are probably responsible for the brain pathology in both disorders. Deficiency of ECHS1 or HIBCH should be considered in children with Leigh disease. Urine metabolite testing can detect and distinguish between these two disorders. © The Author (2014). Published by Oxford University Press on behalf of the Guarantors of Brain. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

QuEChERS sample preparation for the determination of pesticides and other organic residues in environmental matrices: a critical review.

PubMed

Bruzzoniti, Maria Concetta; Checchini, Leonardo; De Carlo, Rosa Maria; Orlandini, Serena; Rivoira, Luca; Del Bubba, Massimo

2014-07-01

Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) is an extraction and clean-up technique originally developed for recovering pesticide residues from fruits and vegetables. Since its introduction, and until December 2013, about 700 papers have been published using the QuEChERS technique, according to a literature overview carried out using SciFinder, Elsevier SciVerse, and Google search engines. Most of these papers were dedicated to pesticide multiresidue analysis in food matrices, and this topic has been thoroughly reviewed over recent years. The QuEChERS approach is now rapidly developing beyond its original field of application to analytes other than pesticides, and matrices other than food, such as biological fluids and non-edible plants, including Chinese medicinal plants. Recently, the QuEChERS concept has spread to environmental applications by analyzing not only pesticides but also other compounds of environmental concern in soil, sediments, and water. To the best of our knowledge, QuEChERS environmental applications have not been reviewed so far; therefore, in this contribution, after a general discussion on the evolution and changes of the original QuEChERS method, a critical survey of the literature regarding environmental applications of conventional and modified QuEChERS methodology is provided. The overall recoveries obtained with QuEChERS and other extraction approaches (e.g., accelerated solvent extraction, ultrasonic solvent extraction, liquid/solid extraction, and soxhlet extraction) were compared, providing evidence for QuEChERS higher recoveries for various classes of compounds, such as biopesticides, chloroalkanes, phenols, and perfluoroalkyl substances. The role of physicochemical properties of soil (i.e., clay and organic carbon content, as well as cation exchange capacity) and target analytes (i.e., log KOW, water solubility, and vapor pressure) were also evaluated in order to interpret recovery and matrix effect data.

Comparison of sample preparation methods combined with fast gas chromatography-mass spectrometry for ultratrace analysis of pesticide residues in baby food.

PubMed

Hercegová, Andrea; Dömötörová, Milena; Kruzlicová, Dása; Matisová, Eva

2006-05-01

Four sample preparation techniques were compared for the ultratrace analysis of pesticide residues in baby food: (a) modified Schenck's method based on ACN extraction with SPE cleaning; (b) quick, easy, cheap, effective, rugged, and safe (QuEChERS) method based on ACN extraction and dispersive SPE; (c) modified QuEChERS method which utilizes column-based SPE instead of dispersive SPE; and (d) matrix solid phase dispersion (MSPD). The methods were combined with fast gas chromatographic-mass spectrometric analysis. The effectiveness of clean-up of the final extract was determined by comparison of the chromatograms obtained. Time consumption, laboriousness, demands on glassware and working place, and consumption of chemicals, especially solvents, increase in the following order QuEChERS < modified QuEChERS < MSPD < modified Schenck's method. All methods offer satisfactory analytical characteristics at the concentration levels of 5, 10, and 100 microg/kg in terms of recoveries and repeatability. Recoveries obtained for the modified QuEChERS method were lower than for the original QuEChERS. In general the best LOQs were obtained for the modified Schenck's method. Modified QuEChERS method provides 21-72% better LOQs than the original method.

Status of the design of the ITER ECE diagnostic

DOE PAGES

Taylor, G.; Austin, M. E.; Beno, J. H.; ...

2015-03-12

In this study, the baseline design for the ITER electron cyclotron emission (ECE) diagnostic has entered the detailed preliminary design phase. Two plasma views are planned, a radial view and an oblique view that is sensitive to distortions in the electron momentum distribution near the average thermal momentum. Both views provide high spatial resolution electron temperature profiles when the momentum distribution remains Maxwellian. The ECE diagnostic system consists of the front-end optics, including two 1000 K calibration sources, in equatorial port plug EP9, the 70-1000 GHz transmission system from the front-end to the diagnostics hall, and the ECE instrumentation inmore » the diagnostics hall. The baseline ECE instrumentation will include two Michelson interferometers that can simultaneously measure ordinary and extraordinary mode ECE from 70 to 1000 GHz, and two heterodyne radiometer systems, covering 122-230 GHz and 244-355 GHz. Significant design challenges include 1) developing highly-reliable 1000 K calibration sources and the associated shutters/mirrors, 2) providing compliant couplings between the front-end optics and the polarization splitter box that accommodate displacements of the vacuum vessel during plasma operations and bake out, 3) protecting components from damage due to stray ECH radiation and other intense millimeter wave emission and 4) providing the low-loss broadband transmission system.« less

Use of enoyl coenzyme A hydratase of Mycobacterium avium subsp. paratuberculosis for the serological diagnosis of Johne's disease.

PubMed

Nagata, Reiko; Kawaji, Satoko; Mori, Yasuyuki

2013-10-01

Johne's disease (JD), caused by Mycobacterium avium subspecies paratuberculosis (MAP), remains difficult to control because of the lack of specific and sensitive diagnostic tests. In order to improve the specificity of sero-diagnosis for JD, the phage display library derived from genomic DNA of MAP was immunoscreened to identify novel antigenic targets. We selected a clone using antibodies from MAP experimentally infected cattle, and annotated its coding sequence as MAP1197 in the MAP genome, which encoded "echA12_2" in the MAP protein (Map-echA) belonging to Enoyl-CoA hydratase, known as a crotonase enzyme. The Map-echA was expressed in Esherichia coli and purified as a histidine-tag recombinant protein (rMap-echA), and the diagnostic potential of the protein was further evaluated by enzyme-linked immunosorbent assays (ELISA). Antibody responses to rMap-echA were higher in MAP-infected cattle than in uninfected cattle. The specificity of the Map-echA ELISA was also confirmed by evaluation with hyper-immune sera against various kinds of Mycobacterium species. Furthermore, in all experimentally infected cattle the antibody against rMap-echA was detected 2-7months earlier than by a commercially available ELISA kit. These results suggested that Map-echA can be used as a specific and sensitive serological diagnostic antigen for the detection of MAP infection. Copyright © 2013 Elsevier B.V. All rights reserved.

[Effect of Ech1 overexpression on biological behavior of mouse hepatocarcinoma Hca-P cells in vitro].

PubMed

Wang, Mei; Song, Bo; Wang, Bo; Zhang, Jun; Tang, Jian-wu

2013-05-01

To investigate the effect of enoyl coenzyme A hydratase-1 (Ech1) on the proliferation and invasion ability of mouse hepatocarcinoma Hca-P cells in vitro. Recombinant pcDNA3.1(+)-Ech1 gene and pcDNA3.1(+) were transfected into Hca-P cells by cationic liposomes introduction. Clone of PEch1 cells that stably expressing Ech1 and clone of control Pvector cells were screened by G418. The Ech1 expression was identified subsequently by reverse transcriptase-polymerase chain reaction (RT-PCR) and enzyme-linked immunosorbent assay (ELISA), respectively. The malignant behaviors of the cell lines were compared by proliferation, invasion and migration test. The cell line Hca-P cells stably expressing Ech1 gene was constructed. The relative expression of Ech1 mRNA in the PEch1 group was 3.21 ± 0.43 and in the Pvector group was 1.44 ± 0.03, with a significant difference between the two groups (P = 0.029). The results of ELISA revealed that the expression of Ech1 protein was 0.140 ± 0.005 in the PEch1 group, 0.088 ± 0.003 in the Pvector group, and 0.078 ± 0.006 in the Hca-P group, showing a significant difference between the PEch1 group and the Pvector and Hca-P groups (P < 0.05). Transwell migration test showed that the number of penetrated cells in the PEch1 group was 143.00 ± 7.25 cells, significantly higher than that of the Pvector group (95.73 ± 3.88 cells) and un-treated Hca-1 group (106.67 ± 3.54 cells, both P < 0.05). The Transwell invasion assay showed that the number of penetrated cells was 77.20 ± 5.46 cells in the PEch1 group, significantly higher than 46.34 ± 4.35 cells in the Pvector group and 49.80 ± 5.21 cells in the un-treated Hca-1 group (both P < 0.05). The results showed that overexpressed Ech1 in Hca-P cells may significantly increase the cell proliferation in a time-dependent manner. The up-regulation of Ech1 may increase to some extent the migration and invasion capacity of Hca-P cells. The efforts aiming at up-regulation of Ech1 expression may become a therapeutic target in the treatment of hepatocarcinoma.

Role of the Trichoderma harzianum Endochitinase Gene, ech42, in Mycoparasitism

PubMed Central

Carsolio, Carolina; Benhamou, Nicole; Haran, Shoshan; Cortés, Carlos; Gutiérrez, Ana; Chet, Ilan; Herrera-Estrella, Alfredo

1999-01-01

The role of the Trichoderma harzianum endochitinase (Ech42) in mycoparasitism was studied by genetically manipulating the gene that encodes Ech42, ech42. We constructed several transgenic T. harzianum strains carrying multiple copies of ech42 and the corresponding gene disruptants. The level of extracellular endochitinase activity when T. harzianum was grown under inducing conditions increased up to 42-fold in multicopy strains as compared with the wild type, whereas gene disruptants exhibited practically no activity. The densities of chitin labeling of Rhizoctonia solani cell walls, after interactions with gene disruptants were not statistically significantly different than the density of chitin labeling after interactions with the wild type. Finally, no major differences in the efficacies of the strains generated as biocontrol agents against R. solani or Sclerotium rolfsii were observed in greenhouse experiments. PMID:10049844

Effects of two hospital bed design features on physical demands and usability during brake engagement and patient transportation: a repeated measures experimental study.

PubMed

Kim, Sunwook; Barker, Linsey M; Jia, Bochen; Agnew, Michael J; Nussbaum, Maury A

2009-03-01

Work-related musculoskeletal disorders (WMSDs) are prevalent among healthcare workers worldwide. While existing research has focused on patient-handling techniques during activities which require direct patient contact (e.g., patient transfer), nursing tasks also involve other patient-handling activities, such as engaging bed brakes and transporting patients in beds, which could render healthcare workers at risk of developing WMSDs. Effectiveness of hospital bed design features (brake pedal location and steering-assistance) was evaluated in terms of physical demands and usability during brake engagement and patient transportation tasks. Two laboratory-based studies were conducted. In simulated brake engagement tasks, three brake pedal locations (head-end vs. foot-end vs. side of a bed) and two hands conditions (hands-free vs. hands-occupied) were manipulated. Additionally, both in-room and corridor patient transportation tasks were simulated, in which activation of steering-assistance features (5th wheel and/or front wheel caster lock) and two patient masses were manipulated. Nine novice participants were recruited from the local student population and community for each study. During brake engagement, trunk flexion angle, task completion time, and questionnaires were used to quantify postural comfort and usability. For patient transportation, dependent measures were hand forces and questionnaire responses. Brake pedal locations and steering-assistance features in hospital beds had significant effects on physical demands and usability during brake engagement and patient transportation tasks. Specifically, a brake pedal at the head-end of a bed increased trunk flexion by 74-224% and completion time by 53-74%, compared to other pedal locations. Participants reported greater overall perceived difficulty and less postural comfort with the brake pedal at the head-end. During in-room transportation, participants generally reported "Neither Low nor High" physical demands with the 5th wheel activated, compared to "Moderately High" physical demands when the 5th wheel was deactivated. Corridor transportation was similarly reported to be easier when a steering-assistance feature (the 5th wheel or front caster lock) was activated. Braking and steering-assistance features of hospital beds can have important effects on task efficiency and physical demands placed on healthcare workers. Selection of specific designs may thus be able to improve productivity and contribute to a reduction in WMSDs risk among healthcare workers.

Animal models for treatment of unresectable liver tumours: a histopathologic and ultra-structural study of cellular toxic changes after electrochemical treatment in rat and dog liver.

PubMed

von Euler, Henrik; Olsson, Jerker M; Hultenby, Kjell; Thörne, Anders; Lagerstedt, Anne-Sofie

2003-04-01

Electrochemical treatment (EChT) has been taken under serious consideration as being one of several techniques for local treatment of malignancies. The advantage of EChT is the minimal invasive approach and the absence of serious side effects. Macroscopic, histopathological and ultra-structural findings in liver following a four-electrode configuration (dog) and a two-electrode EChT design (dog and rat) were studied. 30 female Sprague-Dawley rats and four female beagle dogs were studied with EChT using Platinum:Iridium electrodes and the delivered dose was 5, 10 or 90 C (As). After EChT, the animals were euthanized. The distribution of the lesions was predictable, irrespective of dose and electrode configuration. Destruction volumes were found to fit into a logarithmic curve (dose-response). Histopathological examination confirmed a spherical (rat) and cylindrical/ellipsoidal (dog) lesion. The type of necrosis differed due to electrode polarity. Ultra-structural analysis showed distinct features of cell damage depending on the distance from the electrode. Histopathological and ultra-structural examination demonstrated that the liver tissue close to the border of the lesion displayed a normal morphology. The in vivo dose-planning model is reliable, even in species with larger tissue mass such as dogs. A multi-electrode EChT-design could obtain predictable lesions. The cellular toxicity following EChT is clearly identified and varies with the distance from the electrode and polarity. The distinct border between the lesion and normal tissue suggests that EChT in a clinical setting for the treatment of liver tumours can give a reliable destruction margin.

Epichlorohydrin induced biochemical changes in the rose-ringed parakeet, Psittacula krameri Scopoli.

PubMed

Hans, B; Kaur, S; Sangha, G K

1999-08-01

Intraperitoneal administration of epichlorohydrin (ECH) at the dose level of 20 and 50 mg/kg body weight inhibited spermatogenesis in the testis of parakeet during breeding season. A total load of 60 mg/kg body weight of ECH given on 3 consecutive days proved to be lethal. Testicular proteins, nucleic acids (DNA and RNA), phospholipids and acid phosphatase activity were decreased, while the lipids, total cholesterol and alkaline phosphatase activity increased after ECH administration. The results suggest that the testicular atrophy caused by ECH was associated with an alteration in the activities of macromolecules and enzymes related to specific events of spermatogenesis.

Kelch-like ECH-associated Protein 1-dependent Nuclear Factor-E2-related Factor 2 Activation in Relation to Antioxidation Induced by Sevoflurane Preconditioning.

PubMed

Cai, Min; Tong, Li; Dong, Beibei; Hou, Wugang; Shi, Likai; Dong, Hailong

2017-03-01

The authors have reported that antioxidative effects play a crucial role in the volatile anesthetic-induced neuroprotection. Accumulated evidence shows that endogenous antioxidation could be up-regulated by nuclear factor-E2-related factor 2 through multiple pathways. However, whether nuclear factor-E2-related factor 2 activation is modulated by sevoflurane preconditioning and, if so, what is the signaling cascade underlying upstream of this activation are still unknown. Sevoflurane preconditioning in mice was performed with sevoflurane (2.5%) 1 h per day for five consecutive days. Focal cerebral ischemia/reperfusion injury was induced by middle cerebral artery occlusion. Expression of nuclear factor-E2-related factor 2, kelch-like ECH-associated protein 1, manganese superoxide dismutase, thioredoxin-1, and nicotinamide adenine dinucleotide phosphate quinolone oxidoreductase-1 was detected (n = 6). The antioxidant activities and oxidative product expression were also examined. To determine the role of kelch-like ECH-associated protein 1 inhibition-dependent nuclear factor-E2-related factor 2 activation in sevoflurane preconditioning-induced neuroprotection, the kelch-like ECH-associated protein 1-nuclear factor-E2-related factor 2 signal was modulated by nuclear factor-E2-related factor 2 knockout, kelch-like ECH-associated protein 1 overexpression lentivirus, and kelch-like ECH-associated protein 1 deficiency small interfering RNA (n = 8). The infarct volume, neurologic scores, and cellular apoptosis were assessed. Sevoflurane preconditioning elicited neuroprotection and increased nuclear factor-E2-related factor 2 nuclear translocation, which in turn up-regulated endogenous antioxidation and reduced oxidative injury. Sevoflurane preconditioning reduced kelch-like ECH-associated protein 1 expression. Nuclear factor-E2-related factor 2 ablation abolished neuroprotection and reversed sevoflurane preconditioning by mediating the up-regulation of antioxidants. Kelch-like ECH-associated protein 1 overexpression reversed nuclear factor-E2-related factor 2 up-regulation and abolished the neuroprotection induced by sevoflurane preconditioning. Kelch-like ECH-associated protein 1 small interfering RNA administration improved nuclear factor-E2-related factor 2 expression and the outcome of mice subjected to ischemia/reperfusion injury. Kelch-like ECH-associated protein 1 down-regulation-dependent nuclear factor-E2-related factor 2 activation underlies the ability of sevoflurane preconditioning to activate the endogenous antioxidant response, which elicits its neuroprotection.

Changes in the Severity and Injury Sources of Thoracic Aorta Injuries due to Vehicular Crashes.

PubMed

Ryb, Gabriel; Dischinger, Patricia; Kerns, Timothy; Burch, Cynthia; Rabin, Joseph; Ho, Shiu

Research using the National Automotive Sampling System-Crashworthiness Data System (NASS-CDS) suggested a decreased adjusted risk of thoracic aorta injuries (TAI) for newer vehicles during near-side crashes and an increased adjusted TAI risk during frontal crashes. This study attempted to explore possible explanations of these findings. Adult front seat occupants in the Crash Injury Research and Engineering Network (CIREN) database through June 2012 were studied. TAI cases were compared with remaining cases in relation to crash and vehicular characteristics. TAI cases of later crash year (CY) (2004-2012) were compared to those in earlier CY (1996-2003) in relation to TAI severity (minor, moderate, severe and non-survivable). TAI cases in newer model year (MY) vehicles (1999-2012) were compared to those in older vehicles (1988-98) in relation to injury source (steering wheel, front, left, seat belt, air bag and other or unknown). Analysis was stratified by direction of impact (frontal and near-side) and the use of restraints. The similar TAI severity of earlier and later CY among frontal crashes suggests that the observed changes in the adjusted odds of injury seen in NASS-CDS are not due to an increase in injury detection. The decrease in TAI severity among newer vehicles in near-side crashes of later CY is consistent with a beneficial effect of crashworthiness improvements for this crash configuration. A shift of injury source in frontal crashes from the steering wheel in older vehicles to "front of vehicle structures", "seat belts" and "unknown and other" in newer vehicles should suggest potential sites for crashworthiness improvements.

Striations and preferred eddy tracks triggered by topographic steering of the background flow in the eastern South Pacific

NASA Astrophysics Data System (ADS)

Belmadani, Ali; Concha, Emilio; Donoso, David; Chaigneau, Alexis; Colas, François; Maximenko, Nikolai; Di Lorenzo, Emanuele

2017-04-01

In recent years, persistent quasi-zonal jets or striations have been ubiquitously detected in the world ocean using satellite and in situ data as well as numerical models. This study aims at determining the role of mesoscale eddies in the generation and persistence of striations off Chile in the eastern South Pacific. A 50 year climatological integration of an eddy-resolving numerical ocean model is used to assess the long-term persistence of striations. Automated eddy tracking algorithms are applied to the model outputs and altimetry data. Results reveal that striations coincide with both polarized eddy tracks and the offshore formation of new eddies in the subtropical front and coastal transition zone, without any significant decay over time that discards random eddies as a primary driver of the striations. Localized patches of vortex stretching and relative vorticity advection, alternating meridionally near the eastern edge of the subtropical front, are associated with topographic steering of the background flow in the presence of steep topography, and with baroclinically and barotropically unstable meridional flow. These sinks and sources of vorticity are suggested to generate the banded structure further west, consistently with a β-plume mechanism. On the other hand, zonal/meridional eddy advection of relative vorticity and the associated Reynolds stress covariance are consistent with eddy deformation over rough topography and participate to sustain the striations in the far field. Shear instability of mean striations is proposed to feedback onto the eddy field, acting to maintain the subtropical front eddy streets and thus the striations.

Autonomous vehicle navigation utilizing fuzzy controls concepts for a next generation wheelchair.

PubMed

Hansen, J D; Barrett, S F; Wright, C H G; Wilcox, M

2008-01-01

Three different positioning techniques were investigated to create an autonomous vehicle that could accurately navigate towards a goal: Global Positioning System (GPS), compass dead reckoning, and Ackerman steering. Each technique utilized a fuzzy logic controller that maneuvered a four-wheel car towards a target. The reliability and the accuracy of the navigation methods were investigated by modeling the algorithms in software and implementing them in hardware. To implement the techniques in hardware, positioning sensors were interfaced to a remote control car and a microprocessor. The microprocessor utilized the sensor measurements to orient the car with respect to the target. Next, a fuzzy logic control algorithm adjusted the front wheel steering angle to minimize the difference between the heading and bearing. After minimizing the heading error, the car maintained a straight steering angle along its path to the final destination. The results of this research can be used to develop applications that require precise navigation. The design techniques can also be implemented on alternate platforms such as a wheelchair to assist with autonomous navigation.

Electronically-Controlled Beam-Steering through Vanadium Dioxide Metasurfaces

PubMed Central

Hashemi, Mohammed Reza M.; Yang, Shang-Hua; Wang, Tongyu; Sepúlveda, Nelson; Jarrahi, Mona

2016-01-01

Engineered metamaterials offer unique functionalities for manipulating the spectral and spatial properties of electromagnetic waves in unconventional ways. Here, we report a novel approach for making reconfigurable metasurfaces capable of deflecting electromagnetic waves in an electronically controllable fashion. This is accomplished by tilting the phase front of waves through a two-dimensional array of resonant metasurface unit-cells with electronically-controlled phase-change materials embedded inside. Such metasurfaces can be placed at the output facet of any electromagnetic radiation source to deflect electromagnetic waves at a desired frequency, ranging from millimeter-wave to far-infrared frequencies. Our design does not use any mechanical elements, external light sources, or reflectarrays, creating, for the first time, a highly robust and fully-integrated beam-steering device solution. We demonstrate a proof-of-concept beam-steering metasurface optimized for operation at 100 GHz, offering up to 44° beam deflection in both horizontal and vertical directions. Dynamic control of electromagnetic wave propagation direction through this unique platform could be transformative for various imaging, sensing, and communication applications, among others. PMID:27739471

Swimming micro-robot powered by stimuli-sensitive gel

NASA Astrophysics Data System (ADS)

Masoud, Hassan; Alexeev, Alexander

2012-11-01

Using three-dimensional computer simulations, we design a simple maneuverable micro-swimmer that can self-propel and navigate in highly viscous (low Reynolds-number) environments. Our simple swimmer consists of a cubic gel body which periodically changes volume in response to external stimuli, two rigid rectangular flaps attached to the opposite sides of the gel body, and a flexible steering flap at the front end of the swimmer. The stimuli-sensitive body undergoes periodic expansions (swelling) and contractions (deswelling) leading to a time-irreversible beating motion of the propulsive flaps that propel the micro-swimmer. Thus, the responsive gel body acts as an ``engine'' actuating the motion of the swimmer. We examine how the swimming speed depends on the gel and flap properties. We also probe how the swimmer trajectory can be changed using a responsive steering flap whose curvature is controlled by an external stimulus. We show that the turning occurs due to steering flap bending and periodic beating. Furthermore, our simulations reveal that the turning direction can be regulated by changing the intensity of external stimulus.

Optimization Under Uncertainty for Wake Steering Strategies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quick, Julian; Annoni, Jennifer; King, Ryan N

Offsetting turbines' yaw orientations from incoming wind is a powerful tool that may be leveraged to reduce undesirable wake effects on downstream turbines. First, we examine a simple two-turbine case to gain intuition as to how inflow direction uncertainty affects the optimal solution. The turbines are modeled with unidirectional inflow such that one turbine directly wakes the other, using ten rotor diameter spacing. We perform optimization under uncertainty (OUU) via a parameter sweep of the front turbine. The OUU solution generally prefers less steering. We then do this optimization for a 60-turbine wind farm with unidirectional inflow, varying the degreemore » of inflow uncertainty and approaching this OUU problem by nesting a polynomial chaos expansion uncertainty quantification routine within an outer optimization. We examined how different levels of uncertainty in the inflow direction effect the ratio of the expected values of deterministic and OUU solutions for steering strategies in the large wind farm, assuming the directional uncertainty used to reach said OUU solution (this ratio is defined as the value of the stochastic solution or VSS).« less

ECH Technology Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Temkin, Richard

2014-12-24

Electron Cyclotron Heating (ECH) is needed for plasma heating, current drive, plasma stability control, and other applications in fusion energy sciences research. The program of fusion energy sciences supported by U. S. DOE, Office of Science, Fusion Energy Sciences relies on the development of ECH technology to meet the needs of several plasma devices working at the frontier of fusion energy sciences research. The largest operating ECH system in the world is at DIII-D, consisting of six 1 MW, 110 GHz gyrotrons capable of ten second pulsed operation, plus two newer gyrotrons. The ECH Technology Development research program investigated themore » options for upgrading the DIII-D 110 GHz ECH system. Options included extending present-day 1 MW technology to 1.3 – 1.5 MW power levels or developing an entirely new approach to achieve up to 2 MW of power per gyrotron. The research consisted of theoretical research and designs conducted by Communication and Power Industries of Palo Alto, CA working with MIT. Results of the study would be validated in a later phase by research on short pulse length gyrotrons at MIT and long pulse / cw gyrotrons in industry. This research follows a highly successful program of development that has led to the highly reliable, six megawatt ECH system at the DIII-D tokamak. Eventually, gyrotrons at the 1.5 megawatt to multi-megawatt power level will be needed for heating and current drive in large scale plasmas including ITER and DEMO.« less

Compact Hybrid Automotive Propulsion System

NASA Technical Reports Server (NTRS)

Lupo, G.

1986-01-01

Power train proposed for experimental vehicle powered by internal combustion engine and electric motor. Intended for front-wheel drive automobile, power train mass produced using existing technology. System includes internal-combustion engine, electric motor, continuously variable transmission, torque converter, differential, and control and adjustment systems for electric motor and transmission. Continuously variable transmission integrated into hydraulic system that also handles power steering and power brakes. Batteries for electric motor mounted elsewhere in vehicle.

TARDEC Ground Vehicle Robotics: Vehicle Dynamic Characterization and Research

DTIC Science & Technology

2015-09-01

inferred roll angles that are found with the IMU . This is usually done with UNCLASSIFIED UNCLASSIFIED linear potentiometers, which have an electrical...wire electric, Electric traction control. Suspension Styles: Suspension is what keeps the vehicle off the ground and mechanically isolated from the...lot” maneuvers. Because of this, they roll with no slip angles. This means that the steering angles of the front wheels must be calibrated perfectly

Advanced Optics for a Full Quasi-Optical Front Steering ECRH Upper Launcher for ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moro, A.; Alessi, E.; Bruschi, A.

2009-11-26

A full quasi-optical setup for the internal optics of the Front Steering Electron Cyclotron Resonance Heating (ECRH) Upper Launcher for ITER was designed, proving to be feasible and favorable in terms of additional flexibility and cost reduction with respect to the former design. This full quasi-optical solution foresees the replacement of the mitre-bends in the final section of the launcher with dedicated free-space mirrors to realize the last changes of directions in the launcher. A description of the launcher is given and its advantages presented. The parameters of the expected output beams as well as preliminary evaluations of truncation effectsmore » with the physical optics GRASP code are shown. Moreover, a study of mitre-bends replacement with single mirrors for multiple beams is described. In principle it could allow the beams to be larger at the mirror locations (with a further decrease of the peak power density due to partial overlapping) and has the additional advantage to get a larger opening with compressed beams to avoid conflicts with side-walls port. Constraints on the setup, arising both from the resulting beam characteristics in the space of free parameters and from mechanical requirements are taken into account in the analysis.« less

Performance Optimization Control of ECH using Fuzzy Inference Application

NASA Astrophysics Data System (ADS)

Dubey, Abhay Kumar

Electro-chemical honing (ECH) is a hybrid electrolytic precision micro-finishing technology that, by combining physico-chemical actions of electro-chemical machining and conventional honing processes, provides the controlled functional surfaces-generation and fast material removal capabilities in a single operation. Process multi-performance optimization has become vital for utilizing full potential of manufacturing processes to meet the challenging requirements being placed on the surface quality, size, tolerances and production rate of engineering components in this globally competitive scenario. This paper presents an strategy that integrates the Taguchi matrix experimental design, analysis of variances and fuzzy inference system (FIS) to formulate a robust practical multi-performance optimization methodology for complex manufacturing processes like ECH, which involve several control variables. Two methodologies one using a genetic algorithm tuning of FIS (GA-tuned FIS) and another using an adaptive network based fuzzy inference system (ANFIS) have been evaluated for a multi-performance optimization case study of ECH. The actual experimental results confirm their potential for a wide range of machining conditions employed in ECH.

New method for determination of epichlorohydrin in epoxy-coated cans by oxolane derivatization and gas chromatography-mass spectrometry.

PubMed

Sung, Jun Hyun; Lee, Young Ja; Park, Hyun Jin

2008-08-01

A new method was developed for the determination of epichlorohydrin (ECH) in food contact surface of epoxy-coated cans. The oxolane derivative, which produced by reaction of epoxy moiety in ECH with cyclopentanone in the presence of borontrifluoride-diethyletherate, was analyzed by gas chromatography (GC)/mass spectrometry (MS). 1,2-Epoxyhexane was used as internal standard (IS), which produced an oxolane derivative under the same reaction mechanism as ECH. The developed method was validated with 1 ng ml(-1) of limit of detection (LOD, surface area related 20 ng dm(-2)), >0.999 of linearity. Good precision, which was tested both in terms of intra-day repeatability and inter-day reproducibility, and 97.3-102.7% of good recoveries were obtained on three spiked levels of 5.2, 40.3 and 149.1 ng ml(-1). The excellent validation data suggests that this method is more simple, quick and effective than the official method in European Committee for Standardization (CEN) to determine the residual amount of ECH in food contact materials for food law compliance test. The residual amount of ECH for 13 epoxy-coated can samples was analyzed, and none of the samples was found to be detectable levels of ECH in epoxy-coated cans.

DIFFUSE AURORA ON GANYMEDE DRIVEN BY ELECTROSTATIC WAVES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singhal, R. P.; Tripathi, A. K.; Halder, S.

The role of electrostatic electron cyclotron harmonic (ECH) waves in producing diffuse auroral emission O i 1356 Å on Ganymede is investigated. Electron precipitation flux entering the atmosphere of Ganymede due to pitch-angle diffusion by ECH waves into the atmospheric loss-cone is calculated. The analytical yield spectrum approach for electron energy degradation in gases is used for calculating diffuse auroral intensities. It is found that calculated O i 1356 Å intensity resulting from the precipitation of magnetospheric electrons observed near Ganymede is insufficient to account for the observed diffuse auroral intensity. This is in agreement with estimates made in earliermore » works. Heating and acceleration of ambient electrons by ECH wave turbulence near the magnetic equator on the field line connecting Ganymede and Jupiter are considered. Two electron distribution functions are used to simulate the heating effect by ECH waves. Use of a Maxwellian distribution with temperature 100 eV can produce about 50–70 Rayleigh O i 1356 Å intensities, and the kappa distribution with characteristic energy 50 eV also gives rise to intensities with similar magnitude. Numerical experiments are performed to study the effect of ECH wave spectral intensity profile, ECH wave amplitude, and temperature/characteristic energy of electron distribution functions on the calculated diffuse auroral intensities. The proposed missions, joint NASA/ESA Jupiter Icy Moon Explorer and the present JUNO mission to Jupiter, would provide new data to constrain the ECH wave and other physical parameters near Ganymede. These should help confirm the findings of the present study.« less

Phylogenetic Evidence for H2 based Electron Bifurcation In Early Life

NASA Astrophysics Data System (ADS)

Adams, M. W.; Boyd, E. S.; Schut, G.; Peters, J.

2012-12-01

Energy conservation is a fundamental underpinning of all life and is accomplished by electron transport phosphorylation and/or substrate level phosphorylation. A third mechanism, known as flavin-based electron bifurcation, has recently been established as a mechanism by which life can conserve energy. In this mechanism, a flavin-containing multienzyme complex catalyzes the thermodynamically unfavorable reduction of low potential ferredoxin using electron donors with higher potentials, such as NAD(P)H or H2. Such endergonic reactions are driven forward through the simultaneous oxidation of the electron donor with higher potential acceptors such as NAD+ or heterodisulfide. Membrane associated energy converting [NiFe]hydrogenases (Ech, Eha) link the oxidation of ferredoxin with the production of H2 and in the process conserve energy in the form of an ion (Na+/H+) gradient. Ech/Eha exhibit a modular composition represented by a Na+/H+ antiporter domain and a [NiFe] hydrogenase domain. In addition, Ech/Eha can be accompanied by a formate dehyrogenase, carbon monoxide dehydrogenase, or an FAD/NAD(P)H module that enables coupling with these substrates. Representatives of Ech/Eha have been identified among anaerobic Archaea and Bacteria, including deeply rooted methanogens, sulfur-reducing Crenarcheota/Euryarchaeota as well as Thermotogae. Ech exhibit extensive homology to a number of subunits within the NADH quinone oxidoreductase or complex I family (Nuo, Fpo). Metabolically, Ech generally couple the oxidation of carbon monooxide, formate or ferredoxin to the production of H2. In contrast, the Eha complex couples the translocation of Na+ and the oxidation of H2 to the reduction of ferredoxin, which is then available for the reduction of CO2 in methanogens. In the case of Eha, the gradient of Na+/H+ produced through translocation coupled to ferredoxin oxidation can in be used to drive the phosphorylation of ADP via an ATP synthase complex, thereby representing one of the most simple forms of ATP production supporting life. This finding is consistent with phylogenetic analyses which indicate a close phylogenetic relationship between Ech/Eha and Nuo/Fpo, with [NiFe]-hydrogenase typically involved in H2 oxidation forming divergent lineages. This suggests that Ech/Eha are most likely to represent an ancestor of the Complex I family and the [NiFe]-hydrogenase family. A concatenation and phylogenetic analysis of the large and small subunits of Ech and Nuo was performed and and additional modules enabling coupling with CO2 (Eha), CO (Ech-CODH), and formate (Ech-Fdh) through H2-based electron bifurcation were overlaid on this phylogeny. The results suggest an origin for H2-based electron bifurcation via Ech/Eha among CO2 reducing hydrogenotrophic methanogenic Archaea or sulfur-reducing Archaea, with evolution towards coupling with formate and CO. These results provide insight into the evolutionary relationships between electron bifurcation-enabled ionic gradients capable of driving phosphorylation and electron transport-based phosphorylation. Moreover, these observations suggest that electron bifurcation may have been important in overcoming key metabolic bottlenecks and may have enabled life to access small energetic gradients to support metabolism on early Earth.

Steering of Upper Ocean Currents and Fronts by the Topographically Constrained Abyssal Circulation

DTIC Science & Technology

2008-07-06

a) Mean surface dynamic height relative to 1000 m from version 2.5 of the Generalized Digital Environmental Model ( GDEM ) oceanic climatology, an...NLOM simulations in comparison to the mean surface dynamic height with respect to 1000 m from the Generalized Digital Environmental Model ( GDEM ...the Kuroshio pathway east of Japan, giving much better agreement with the pathway in the GDEM climatology. Dynamics of the topographic impact on

Laboratory Performance of Five Selected Soil Moisture Sensors Applying Factory and Own Calibration Equations for Two Soil Media of Different Bulk Density and Salinity Levels

PubMed Central

Matula, Svatopluk; Báťková, Kamila; Legese, Wossenu Lemma

2016-01-01

Non-destructive soil water content determination is a fundamental component for many agricultural and environmental applications. The accuracy and costs of the sensors define the measurement scheme and the ability to fit the natural heterogeneous conditions. The aim of this study was to evaluate five commercially available and relatively cheap sensors usually grouped with impedance and FDR sensors. ThetaProbe ML2x (impedance) and ECH2O EC-10, ECH2O EC-20, ECH2O EC-5, and ECH2O TE (all FDR) were tested on silica sand and loess of defined characteristics under controlled laboratory conditions. The calibrations were carried out in nine consecutive soil water contents from dry to saturated conditions (pure water and saline water). The gravimetric method was used as a reference method for the statistical evaluation (ANOVA with significance level 0.05). Generally, the results showed that our own calibrations led to more accurate soil moisture estimates. Variance component analysis arranged the factors contributing to the total variation as follows: calibration (contributed 42%), sensor type (contributed 29%), material (contributed 18%), and dry bulk density (contributed 11%). All the tested sensors performed very well within the whole range of water content, especially the sensors ECH2O EC-5 and ECH2O TE, which also performed surprisingly well in saline conditions. PMID:27854263

ECH-assisted startup at KSTAR

NASA Astrophysics Data System (ADS)

Bae, Y. S.; Jeong, J. H.; Park, S. I.; Cho, M. H.; Namkung, W.; Jackson, G. L.; Joung, M.; Yoon, S. W.; Kim, J. H.; Hahn, S. H.; Kim, W. C.; Yang, H. L.; Oh, Y. K.; Humphreys, D.; Walker, M. L.; Gorelov, Y.; Leuer, J. A.; Hyatt, A. W.; Eidietis, N. W.; Mueller, D.; Bak, J. S.; Kwon, M.

2009-11-01

The electron cyclotron heating (ECH)-assisted startup was successful in the Korea Superconducting Tokamak Advanced Research (KSTAR) first plasma campaign completed in June, 2008. It was observed that the second harmonic EC wave of 0.35 MW was sufficient to achieve breakdown in the ECH pre-ionization phase, to allow burn through, and to sustain the plasma during the current ramp with a low loop voltage of 2.0 V. This corresponds to a toroidal electric field of 0.24 Vm-1 at the innermost vacuum vessel wall (R = 1.3 m). Since there is no feedback control of the plasma radial position in the initial phase of the KSTAR first plasma campaign, wall contact caused the plasma current fall to zero soon after the ECH beam was turned off. Extending pulse duration of the ECH power to 190 ms allowed the plasma current to rise up to more than 100 kA with a ramp-up rate of 0.8 MA/s and the pulse duration of 210 ms. Later in the first plasma campaign, the plasma was sustained up to 865 ms with the help of additional heating of 350-ms long ECH beam and with the help of the plasma radial position feedback control. The plasma current in the pre-ionization phase was observed and it is considered to be pressure-driven Pfirsch-Schlüter current.

Generation of lower and upper bands of electrostatic electron cyclotron harmonic waves in the Van Allen radiation belts

DOE PAGES

Zhou, Qinghua; Xiao, Fuliang; Yang, Chang; ...

2017-05-22

Electrostatic electron cyclotron harmonic (ECH) waves generated by the electron loss cone distribution can produce efficient scattering loss of plasma sheet electrons, which has a significant effect on the dynamics in the outer magnetosphere. Here we report two ECH emission events around the same location L≈ 5.7–5.8, MLT ≈ 12 from Van Allen Probes on 11 February (event A) and 9 January 2014 (event B), respectively. The spectrum of ECH waves was centered at the lower half of the harmonic bands during event A, but the upper half during event B. The observed electron phase space density in both eventsmore » is fitted by the subtracted bi-Maxwellian distribution, and the fitting functions are used to evaluate the local growth rates of ECH waves based on a linear theory for homogeneous plasmas. ECH waves are excited by the loss cone instability of 50 eV–1 keV electrons in the lower half of harmonic bands in the low-density plasmasphere in event A, and 1–10 keV electrons in the upper half of harmonic bands in a relatively high-density region in event B. Here, the current results successfully explain observations and provide a first direct evidence on how ECH waves are generated in the lower and upper half of harmonic frequency bands.« less

Generation of lower and upper bands of electrostatic electron cyclotron harmonic waves in the Van Allen radiation belts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Qinghua; Xiao, Fuliang; Yang, Chang

Electrostatic electron cyclotron harmonic (ECH) waves generated by the electron loss cone distribution can produce efficient scattering loss of plasma sheet electrons, which has a significant effect on the dynamics in the outer magnetosphere. Here we report two ECH emission events around the same location L≈ 5.7–5.8, MLT ≈ 12 from Van Allen Probes on 11 February (event A) and 9 January 2014 (event B), respectively. The spectrum of ECH waves was centered at the lower half of the harmonic bands during event A, but the upper half during event B. The observed electron phase space density in both eventsmore » is fitted by the subtracted bi-Maxwellian distribution, and the fitting functions are used to evaluate the local growth rates of ECH waves based on a linear theory for homogeneous plasmas. ECH waves are excited by the loss cone instability of 50 eV–1 keV electrons in the lower half of harmonic bands in the low-density plasmasphere in event A, and 1–10 keV electrons in the upper half of harmonic bands in a relatively high-density region in event B. Here, the current results successfully explain observations and provide a first direct evidence on how ECH waves are generated in the lower and upper half of harmonic frequency bands.« less

Changes in the Severity and Injury Sources of Thoracic Aorta Injuries due to Vehicular Crashes

PubMed Central

Ryb, Gabriel; Dischinger, Patricia; Kerns, Timothy; Burch, Cynthia; Rabin, Joseph; Ho, Shiu

2013-01-01

Research using the National Automotive Sampling System-Crashworthiness Data System (NASS-CDS) suggested a decreased adjusted risk of thoracic aorta injuries (TAI) for newer vehicles during near-side crashes and an increased adjusted TAI risk during frontal crashes. This study attempted to explore possible explanations of these findings. Adult front seat occupants in the Crash Injury Research and Engineering Network (CIREN) database through June 2012 were studied. TAI cases were compared with remaining cases in relation to crash and vehicular characteristics. TAI cases of later crash year (CY) (2004–2012) were compared to those in earlier CY (1996–2003) in relation to TAI severity (minor, moderate, severe and non-survivable). TAI cases in newer model year (MY) vehicles (1999–2012) were compared to those in older vehicles (1988–98) in relation to injury source (steering wheel, front, left, seat belt, air bag and other or unknown). Analysis was stratified by direction of impact (frontal and near-side) and the use of restraints. The similar TAI severity of earlier and later CY among frontal crashes suggests that the observed changes in the adjusted odds of injury seen in NASS-CDS are not due to an increase in injury detection. The decrease in TAI severity among newer vehicles in near-side crashes of later CY is consistent with a beneficial effect of crashworthiness improvements for this crash configuration. A shift of injury source in frontal crashes from the steering wheel in older vehicles to “front of vehicle structures”, “seat belts” and “unknown and other” in newer vehicles should suggest potential sites for crashworthiness improvements. PMID:24406956

Integrated control design for driver assistance systems based on LPV methods

NASA Astrophysics Data System (ADS)

Gáspár, Péter; Németh, Balázs

2016-12-01

The paper proposes a control design method for a driver assistance system. In the operation of the system, a predefined trajectory required by the driver with a steering command is followed. During manoeuvres the control system generates differential brake moment and the auxiliary front-wheel steering angle and changes the camber angles of the wheels in order to improve the tracking of the road trajectory. The performance specifications are guaranteed by the local controllers, i.e. the brake, the steering, and the suspension systems, while the coordination of these components is provided by the supervisor. The advantage of this architecture is that local controllers are designed independently, which is ensured by the fact that the monitoring signals are taken into consideration in the formalisation of their performance specifications. The fault-tolerant control can be achieved by incorporating the detected fault signals in their performance specifications. The control system also uses a driver model, with which the reference signal can be generated. In the control design, the parameter-dependent linear parameter-varyingmethod, which meets the performance specifications, is used. The operation of the control system is illustrated through different normal and emergency vehicle manoeuvres with a high-accuracy simulation software.

Electron Cyclotron Heating system status and upgrades on DIII-D

DOE PAGES

Cengher, Mirela; Lohr, John; Gorelov, Yuri; ...

2016-06-02

The Electron Cyclotron Heating (ECH) system on the DIII-D tokamak consists of six 110 GHz gyrotrons with corrugated coaxial 31.75 mm waveguide transmission lines and steerable launching mirrors. The system has been gradually updated, leading to increased experimental flexibility and a high system reliability of 91% in the past year. Operationally, the gyrotrons can generate up to a total of 4.8 MW of rf power for pulses up to 5 seconds in length. The maximum ECH energy injected into the DIII-D has been 16.6 MJ. The HE11 mode content is over 85% for all the lines, and the transmission coefficientmore » is better than -1.1 dB for all the transmission lines, close to the theoretical value. A new depressed collector gyrotron was recently installed and was injecting up to 640 kW of power into the plasma during 2014-2015 tokamak operations. Three dual waveguide launchers, which can steer the RF beams ±20 degrees poloidally and toroidally, were used for real-time neoclassical tearing mode control and suppression. The launchers now have increased poloidal scanning speed and beam positioning accuracy of ~±2 mm at the plasma center. A new method of in-situ calibration of the mirror angle was used in conjunction with the upgrading of the encoders and motors for the launchers. Two more gyrotrons are expected to be installed and operational in 2015-2016. The first is a repaired 110 GHz, 1 MW gyrotron that had a gun failure after more than 11 years of operation at DIII-D. The second is a newly designed depressed collector tube in the 1.5 MW class, operating at 117.5 GHz, manufactured by Communications and Power Industries (CPI). It operates in the TE20,9 mode and has achieved 1.8 MW for short pulses during factory testing. Furthermore, this gyrotron is undergoing rework to address a high voltage standoff problem.« less

Honeybees Prefer to Steer on a Smooth Wall With Tetrapod Gaits

PubMed Central

Zhao, Jieliang; Zhu, Fei; Yan, Shaoze

2018-01-01

Abstract Insects are well equipped in walking on complex three-dimensional terrain, allowing them to overcome obstacles or catch prey. However, the gait transition for insects steering on a wall remains unexplored. Here, we find that honeybees adopted a tetrapod gait to change direction when climbing a wall. On the contrary to the common tripod gait, honeybees propel their body forward by synchronously stepping with both middle legs and then both front legs. This process ensures the angle of the central axis of the honeybee to be consistent with the crawling direction. Interestingly, when running in an alternating tripod gait, the central axis of honeybee sways around the center of mass under alternating tripod gait to maintain stability. Experimental results show that tripod, tetrapod, and random gaits result in the amazing consensus harmony on the climbing speed and gait stability, whether climbing on a smooth wall or walking on smooth ground. PMID:29722862

Automatic guidance control of an articulated all-wheel-steered vehicle

NASA Astrophysics Data System (ADS)

Kim, Young Chol; Yun, Kyong-Han; Min, Kyung-Deuk

2014-04-01

This paper presents automatic guidance control of a single-articulated all-wheel-steered vehicle being developed by the Korea Railroad Research Institute. The vehicle has an independent drive motor on each wheel except for the front axle. The guidance controller is designed so that the vehicle follows the given reference path within permissible lateral deviations. We use a three-input/three-output linearised model derived from the nonlinear dynamic model of the vehicle. For the purpose of simplifying the controller and making it tunable, we consider a decentralised control configuration. We first design a second-order decoupling compensator for the two-input/two-output system that is strongly coupled and then design a first-order controller for each decoupled feedback loop by using the characteristic ratio assignment method. The simulation results for the nonlinear dynamic model indicate that the proposed control configuration successfully achieves the design objectives.

Tools for Success in Private Practice.

PubMed

Kasewurm, Gyl

2016-11-01

When it comes to business, there is no one thing that ensures success. However, focusing on helping as many patients as possible and tracking those results, creating a program to gather referrals from your own patients, setting a goal each month, and having a key employee to guide operations at the front desk to ensure that every patient is treated well and has an awesome experience at your office will go a long way to steering a practice to success.

Electron cyclotron heating and core intrinsic rotation reversal in DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grassie, J. S. de, E-mail: degrassie@fusion.gat.com; Boedo, J. A.; Grierson, B. A.

2015-12-10

The effect of electron cyclotron heating (ECH) on the intrinsic rotation profile in DIII-D is shown experimentally. Former DIII-D experiments have shown that ECH tends to cause an interior reduction in the normally co-Ip directed intrinsic rotation profile, and this core rotation can be fully reversed to the opposite direction. This effect is due to a turbulent rearrangement of the interior rotation profile. Here, we show results that there is more than one mechanism causing this. We compare two low density L-mode discharges where the only operational difference is the location of the ECH deposition. At low ECH power, comparablemore » to the Ohmic power, the primary change is in the q-profile accompanied by a reversal of the core intrinsic rotation direction for the more off-axis deposition. The change in the shear of the q-profile fits well with a recent theoretical prediction for this rotation reversal. At higher ECH power, the primary change is in the core electron temperature, Te, accompanied by a hollowing of the rotation profile near the magnetic axis. This effect appears to be due to the change in electron collisionality, consistent with another theoretical, gyrokinetic prediction. The variety of phenomena that could allow ECH to modify the intrinsic rotation profile give some expectation that regions of large velocity shear in the interior could be generated, with the possibility of triggering internal transport barriers.« less

Transport modeling of convection dominated helicon discharges in Proto-MPEX with the B2.5-Eirene code

NASA Astrophysics Data System (ADS)

Owen, L. W.; Rapp, J.; Canik, J.; Lore, J. D.

2017-11-01

Data-constrained interpretative analyses of plasma transport in convection dominated helicon discharges in the Proto-MPEX linear device, and predictive calculations with additional Electron Cyclotron Heating/Electron Bernstein Wave (ECH/EBW) heating, are reported. The B2.5-Eirene code, in which the multi-fluid plasma code B2.5 is coupled to the kinetic Monte Carlo neutrals code Eirene, is used to fit double Langmuir probe measurements and fast camera data in front of a stainless-steel target. The absorbed helicon and ECH power (11 kW) and spatially constant anomalous transport coefficients that are deduced from fitting of the probe and optical data are additionally used for predictive simulations of complete axial distributions of the densities, temperatures, plasma flow velocities, particle and energy fluxes, and possible effects of alternate fueling and pumping scenarios. The somewhat hollow electron density and temperature radial profiles from the probe data suggest that Trivelpiece-Gould wave absorption is the dominant helicon electron heating source in the discharges analyzed here. There is no external ion heating, but the corresponding calculated ion temperature radial profile is not hollow. Rather it reflects ion heating by the electron-ion equilibration terms in the energy balance equations and ion radial transport resulting from the hollow density profile. With the absorbed power and the transport model deduced from fitting the sheath limited discharge data, calculated conduction limited higher recycling conditions were produced by reducing the pumping and increasing the gas fueling rate, resulting in an approximate doubling of the target ion flux and reduction of the target heat flux.

Echinacoside induces rat pulmonary artery vasorelaxation by opening the NO-cGMP-PKG-BKCa channels and reducing intracellular Ca2+ levels

PubMed Central

Gai, Xiang-yun; Wei, Yu-hai; Zhang, Wei; Wuren, Ta-na; Wang, Ya-ping; Li, Zhan-qiang; Liu, Shou; Ma, Lan; Lu, Dian-xiang; Zhou, Yi; Ge, Ri-li

2015-01-01

Aim: Sustained pulmonary vasoconstriction as experienced at high altitude can lead to pulmonary hypertension (PH). The main purpose of this study is to investigate the vasorelaxant effect of echinacoside (ECH), a phenylethanoid glycoside from the Tibetan herb Lagotis brevituba Maxim and Cistanche tubulosa, on the pulmonary artery and its potential mechanism. Methods: Pulmonary arterial rings obtained from male Wistar rats were suspended in organ chambers filled with Krebs-Henseleit solution, and isometric tension was measured using a force transducer. Intracellular Ca2+ levels were measured in cultured rat pulmonary arterial smooth muscle cells (PASMCs) using Fluo 4-AM. Results: ECH (30–300 μmol/L) relaxed rat pulmonary arteries precontracted by noradrenaline (NE) in a concentration-dependent manner, and this effect could be observed in both intact endothelium and endothelium-denuded rings, but with a significantly lower maximum response and a higher EC50 in endothelium-denuded rings. This effect was significantly blocked by L-NAME, TEA, and BaCl2. However, IMT, 4-AP, and Gli did not inhibit ECH-induced relaxation. Under extracellular Ca2+-free conditions, the maximum contraction was reduced to 24.54%±2.97% and 10.60%±2.07% in rings treated with 100 and 300 μmol/L of ECH, respectively. Under extracellular calcium influx conditions, the maximum contraction was reduced to 112.42%±7.30%, 100.29%±8.66%, and 74.74%±4.95% in rings treated with 30, 100, and 300 μmol/L of ECH, respectively. After cells were loaded with Fluo 4-AM, the mean fluorescence intensity was lower in cells treated with ECH (100 μmol/L) than with NE. Conclusion: ECH suppresses NE-induced contraction of rat pulmonary artery via reducing intracellular Ca2+ levels, and induces its relaxation through the NO-cGMP pathway and opening of K+ channels (BKCa and KIR). PMID:25864652

Modification of the surface adsorption properties of alumina-supported Pd catalysts for the electrocatalytic hydrogenation of phenol.

PubMed

Cirtiu, Ciprian Mihai; Hassani, Hicham Oudghiri; Bouchard, Nicolas-Alexandre; Rowntree, Paul A; Ménard, Hugues

2006-07-04

The electrocatalytic hydrogenation (ECH) of phenol has been studied using palladium supported on gamma-alumina (10% Pd-Al2O3) catalysts. The catalyst powders were suspended in aqueous supporting electrolyte solutions containing methanol and short-chain aliphatic acids (acetic acid, propionic acid, or butyric acid) and were dynamically circulated through a reticulated vitreous carbon cathode. The efficiency of the hydrogenation process was measured as a function of the total electrolytic charge and was compared for different types of supporting electrolyte and for various solvent compositions. Our results show that these experimental parameters strongly affect the overall ECH efficiency of phenol. The ECH efficiency and yields vary inversely with the quantity of methanol present in the electrolytic solutions, whereas the presence of aliphatic carboxylic acids increased the ECH efficiency in proportion to the chain length of the specific acids employed. In all cases, ECH efficiency was directly correlated with the adsorption properties of phenol onto the Pd-alumina catalyst in the studied electrolyte solution, as measured independently using dynamic adsorption isotherms. It is shown that the alumina surface binds the aliphatic acids via the carboxylate terminations and transforms the catalyst into an organically functionalized material. Temperature-programmed mass spectrometry analysis and diffuse-reflectance infrared spectroscopy measurements confirm that the organic acids are stably bound to the alumina surface below 200 degrees C, with coverages that are independent of the acid chain length. These reproducibly functionalized alumina surfaces control the adsorption/desorption equilibrium of the target phenol molecules and allow us to prepare new electrocatalytic materials to enhance the efficiency of the ECH process. The in situ grafting of specific aliphatic acids on general purpose Pd-alumina catalysts offers a new and flexible mechanism to control the ECH process to enhance the selectivity, efficiency, and yields according to the properties of the specific target molecule.

Recent experimental results of KSTAR RF heating and current drive

NASA Astrophysics Data System (ADS)

Wang, S. J.; Kim, J.; Jeong, J. H.; Kim, H. J.; Joung, M.; Bae, Y. S.; Kwak, J. G.

2015-12-01

The overview of KSTAR activities on ICRH, LHCD and ECH/CD including the last experimental results and future plan aiming for long-pulse high-beta plasma will be presented. Recently we achieved reasonable coupling of ICRF power to H-mode plasma through several efforts to increase system reliability. Power balance will be discussed on this experiment. LHCD is still struggling in the low power regime. Review of antenna spectrum for the higher coupling in H-mode plasma will be tried. ECH/CD provides 41 sec, 0.8 MW of heating power to support high-performance long-pulse discharge. Also, 170 GHz ECH system is integrated with the Plasma Control System (PCS) for the feedback controlling of NTM. Status and plan of ECH/CD will be discussed. Finally, helicon current drive is being prepared for the next stage of KSTAR operation. The hardware preparation and the calculation results of helicon current drive in KSTAR plasma will be discussed.

Enzyme Diffusion from Trichoderma atroviride (= T. harzianum P1) to Rhizoctonia solani Is a Prerequisite for Triggering of Trichoderma ech42 Gene Expression before Mycoparasitic Contact

PubMed Central

Kullnig, Cornelia; Mach, Robert L.; Lorito, Matteo; Kubicek, Christian P.

2000-01-01

A plate confrontation experiment is commonly used to study the mechanism by which Trichoderma spp. antagonize and parasitize other fungi. Previous work with chitinase gene expression (ech42) during the precontact period of this process in which cellophane and dialysis membranes separated Trichoderma harzianum and its host Rhizoctonia solani resulted in essentially opposite results. Here, we show that cellophane membranes are permeable to proteins up to at least 90 kDa in size but that dialysis membranes are not. ech42 was expressed during the precontact stage of the confrontation between Trichoderma atroviride and its host only if the cellophane was placed between the two fungi. These results are consistent with enzyme diffusion from T. atroviride to R. solani generating the trigger of ech42 gene expression. PMID:10788407

Tools for Success in Private Practice

PubMed Central

Kasewurm, Gyl

2016-01-01

When it comes to business, there is no one thing that ensures success. However, focusing on helping as many patients as possible and tracking those results, creating a program to gather referrals from your own patients, setting a goal each month, and having a key employee to guide operations at the front desk to ensure that every patient is treated well and has an awesome experience at your office will go a long way to steering a practice to success. PMID:28028328

Electron pitch angle diffusion by electrostatic electron cyclotron harmonic waves: The origin of pancake distributions

NASA Astrophysics Data System (ADS)

Horne, Richard B.; Thorne, Richard M.

2000-03-01

It has been suggested that highly anisotropic electron pancake distributions are the result of pitch angle diffusion by electrostatic electron cyclotron harmonic (ECH) and whistler mode waves in the equatorial region. Here we present pitch angle diffusion rates for ECH wave spectra centered at different frequencies with respect to the electron gyrofrequency Ωe corresponding to spacecraft observations. The wave spectra are carefully mapped to the correct resonant electron velocities. We show that previous diffusion calculations of ECH waves at 1.5Ωe, driven by the loss cone instability, result in large diffusion rates confined to a small range of pitch angles near the loss cone and therefore cannot account for pancake distributions. However, when the wave spectrum is centered at higher frequencies in the band (>1.6Ωe), the diffusion rates become very small inside the loss cone, peak just outside, and remain large over a wide range of pitch angles up to 60° or more. When the upper hybrid resonance frequency ωUHR is several times Ωe, ECH waves excited in higher bands also contribute significantly to pitch angle diffusion outside the loss cone up to very large pitch angles. We suggest that ECH waves driven by a loss cone could form pancake distributions as they grow if the wave spectrum extends from the middle to the upper part of the first (and higher) gyroharmonic bands. Alternatively, we suggest that pancake distributions can be formed by outward propagation in a nonhomogeneous medium, so that resonant absorption occurs at higher frequencies between(n+12) and (n+1)Ωe in regions where waves are also growing locally at <=1.5Ωe. The calculated diffusion rates suggest that ECH waves with amplitudes of the order of 1 mV m-1 can form pancake distributions from an initially isotropic distribution on a timescale of a few hours. This is consistent with recent CRRES observations of ECH wave amplitudes following substorm injections near geostationary orbit and the timescales for pancake formation. Persistent but much weaker ECH waves can further intensify and maintain pancake distributions during magnetically quiet periods.

The evolution of convective storms from their footprints on the sea as viewed by synthetic aperture radar from space

NASA Technical Reports Server (NTRS)

Atlas, David; Black, Peter G.

1994-01-01

SEASAT synthetic aperture radar (SAR) echoes from the sea have previously been shown to be the result of rain and winds produced by convective stroms; rain damps the surface waves and causes ech-free holes, while the diverging winds associated with downdraft generate waves and associated echoes surrounding the holes. Gust fronts are also evident. Such a snapshot from 8 July 1978 has been examined in conjunction with ground-based radar. This leads to the conclusion that the SAR storm footprints resulted from storm processes that occurred up to an hour or more prior to the snapshot. A sequence of events is discerned from the SAR imagery in which new cell growth is triggered in between the converging outflows of two preexisting cells. In turn, the new cell generates a mini-squall line along its expanding gust front. While such phenomena are well known over land, the spaceborne SAR now allows important inferences to be made about the nature and frequency of convective storms over the oceans. The storm effects on the sea have significant implications for spaceborne wind scatterometry and rainfall measurements. Some of the findings herein remain speculative because of the great distance to the Miami weather radar-the only source of corroborative data.

LETTER: ECH pre-ionization and assisted startup in the fully superconducting KSTAR tokamak using second harmonic

NASA Astrophysics Data System (ADS)

Bae, Y. S.; Jeong, J. H.; Park, S. I.; Joung, M.; Kim, J. H.; Hahn, S. H.; Yoon, S. W.; Yang, H. L.; Kim, W. C.; Oh, Y. K.; England, A. C.; Namkung, W.; Cho, M. H.; Jackson, G. L.; Bak, J. S.; KSTAR Team

2009-02-01

This letter reports on the successful demonstration of the second harmonic electron cyclotron heating (ECH)-assisted startup in the first plasma experiments recently completed in the fully superconducting Korea Superconducting Tokamak Advanced Research (KSTAR) device whose major and minor radii are 1.8 m and 0.5 m, respectively. For the second harmonic ECH-assisted startup, an 84 GHz EC wave at 0.35 MW was launched before the onset of the toroidal electric field of the Ohmic system. And it was observed that this was sufficient to achieve breakdown in the ECH pre-ionization phase, allow burn-through and sustain the plasma during the current ramp with a low loop voltage of 2.0 V and a corresponding toroidal electric field of 0.24 V m-1at the innermost vacuum vessel wall (R = 1.3 m). This is a lower value than 0.3 Vm-1 which is the maximum electric field in ITER. Due to the limited volt-seconds and the loop voltage of the Ohmic power system, the extended pulse duration of the ECH power up to 180 ms allowed the plasma current to rise up to more than 100 kA with a ramp-up rate of 0.8 MA s-1.

On the potential of the EChO mission to characterize gas giant atmospheres

NASA Astrophysics Data System (ADS)

Barstow, J. K.; Aigrain, S.; Irwin, P. G. J.; Bowles, N.; Fletcher, L. N.; Lee, J.-M.

2013-04-01

Space telescopes such as Exoplanet Characterisation Observatory (EChO) and James Webb Space Telescope (JWST) will be important for the future study of extrasolar planet atmospheres. Both of these missions are capable of performing high sensitivity spectroscopic measurements at moderate resolutions in the visible and infrared, which will allow the characterization of atmospheric properties using primary and secondary transit spectroscopy. We use the Non-linear optimal Estimator for MultivariateE spectral analysis (NEMESIS) radiative transfer and retrieval tool, as developed by Irwin et al. and Lee et al., to explore the potential of the proposed EChO mission to solve the retrieval problem for a range of H2-He planets orbiting different stars. We find that EChO should be capable of retrieving temperature structure to ˜200 K precision and detecting H2O, CO2 and CH4 from a single eclipse measurement for a hot Jupiter orbiting a Sun-like star and a hot Neptune orbiting an M star, also providing upper limits on CO and NH3. We provide a table of retrieval precisions for these quantities in each test case. We expect around 30 Jupiter-sized planets to be observable by EChO; hot Neptunes orbiting M dwarfs are rarer, but we anticipate observations of at least one similar planet.

Sliding mode-based lateral vehicle dynamics control using tyre force measurements

NASA Astrophysics Data System (ADS)

Kunnappillil Madhusudhanan, Anil; Corno, Matteo; Holweg, Edward

2015-11-01

In this work, a lateral vehicle dynamics control based on tyre force measurements is proposed. Most of the lateral vehicle dynamics control schemes are based on yaw rate whereas tyre forces are the most important variables in vehicle dynamics as tyres are the only contact points between the vehicle and road. In the proposed method, active front steering is employed to uniformly distribute the required lateral force among the front left and right tyres. The force distribution is quantified through the tyre utilisation coefficients. In order to address the nonlinearities and uncertainties of the vehicle model, a gain scheduling sliding-mode control technique is used. In addition to stabilising the lateral dynamics, the proposed controller is able to maintain maximum lateral acceleration. The proposed method is tested and validated on a multi-body vehicle simulator.

The relationship between building design and residents' quality of life in extra care housing schemes.

PubMed

Orrell, Alison; McKee, Kevin; Torrington, Judith; Barnes, Sarah; Darton, Robin; Netten, Ann; Lewis, Alan

2013-05-01

Well-designed housing is recognised as being an important factor in promoting a good quality of life. Specialised housing models incorporating care services, such as extra care housing (ECH) schemes are seen as enabling older people to maintain a good quality of life despite increasing health problems that can accompany ageing. Despite the variation in ECH building design little is known about the impact of ECH building design on the quality of life of building users. The evaluation of older people's living environments (EVOLVE) study collected cross-sectional data on building design and quality of life in 23 ECH schemes in England, UK. Residents' quality of life was assessed using the schedule for the evaluation of individual quality of life-direct weighting (SEIQoL-DW) and on the four domains of control, autonomy, self-realisation and pleasure on the CASP-19. Building design was measured on 12 user-related domains by means of a new tool; the EVOLVE tool. Using multilevel linear regression, significant associations were found between several aspects of building design and quality of life. Furthermore, there was evidence that the relationship between building design and quality of life was partly mediated by the dependency of participants and scheme size (number of living units). Our findings suggest that good quality building design in ECH can support the quality of life of residents, but that designing features that support the needs of both relatively independent and frail users is problematic, with the needs of highly dependent users not currently supported as well as could be hoped by ECH schemes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Recent experimental results of KSTAR RF heating and current drive

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, S. J., E-mail: sjwang@nfri.re.kr; Kim, J.; Jeong, J. H.

2015-12-10

The overview of KSTAR activities on ICRH, LHCD and ECH/CD including the last experimental results and future plan aiming for long-pulse high-beta plasma will be presented. Recently we achieved reasonable coupling of ICRF power to H-mode plasma through several efforts to increase system reliability. Power balance will be discussed on this experiment. LHCD is still struggling in the low power regime. Review of antenna spectrum for the higher coupling in H-mode plasma will be tried. ECH/CD provides 41 sec, 0.8 MW of heating power to support high-performance long-pulse discharge. Also, 170 GHz ECH system is integrated with the Plasma Control Systemmore » (PCS) for the feedback controlling of NTM. Status and plan of ECH/CD will be discussed. Finally, helicon current drive is being prepared for the next stage of KSTAR operation. The hardware preparation and the calculation results of helicon current drive in KSTAR plasma will be discussed.« less

Recent Progress on ECH Technology for ITER

NASA Astrophysics Data System (ADS)

Sirigiri, Jagadishwar

2005-10-01

The Electron Cyclotron Heating and Current Drive (ECH&CD) system for ITER is a critical ITER system that must be available for use on Day 1 of the ITER experimental program. The applications of the system include plasma start-up, plasma heating and suppression of Neoclassical Tearing Modes (NTMs). These applications are accomplished using 27 one megawatt continuous wave gyrotrons: 24 at a frequency of 170 GHz and 3 at a frequency of 120 GHz. There are DC power supplies for the gyrotrons, a transmission line system, one launcher at the equatorial plane and three upper port launchers. The US will play a major role in delivering parts of the ECH&CD system to ITER. The present state-of-the-art includes major advances in all areas of ECH technology. In the US, a major effort is underway to supply gyrotrons of up to 1.5 MW power level at 110 GHz to General Atomics for use in heating the DIII-D tokamak. This presentation will include a brief review of the state-of-the-art, worldwide, in ECH technology. The requirements for the ITER ECH&CD system will then be reviewed. ITER calls for gyrotrons capable of operating from a 50 kV power supply, after potential depression, with a minimum of 50% overall efficiency. This is a very significant challenge and some approaches to meeting this goal will be presented. Recent experimental results at MIT showing improved efficiency of high frequency, 1.5 MW gyrotrons will be described. These results will be incorporated into the planned development of gyrotrons for ITER. The ITER ECH&CD system will also be a challenge to the transmission lines, which must operate at high average power at up to 1000 seconds and with high efficiency. The technology challenges and efforts in the US and other ITER parties to solve these problems will be reviewed. *In collaboration with E. Choi, C. Marchewka, I. Mastovosky, M. A. Shapiro and R. J. Temkin. This work is supported by the Office of Fusion Energy Sciences of the U. S. Department of Energy.

Progress of long pulse discharges by ECH in LHD

NASA Astrophysics Data System (ADS)

Yoshimura, Y.; Kasahara, H.; Tokitani, M.; Sakamoto, R.; Ueda, Y.; Ito, S.; Okada, K.; Kubo, S.; Shimozuma, T.; Igami, H.; Takahashi, H.; Tsujimura, T. I.; Makino, R.; Kobayashi, S.; Mizuno, Y.; Akiyama, T.; Ashikawa, N.; Masuzaki, S.; Motojima, G.; Shoji, M.; Suzuki, C.; Tanaka, H.; Tanaka, K.; Tokuzawa, T.; Tsuchiya, H.; Yamada, I.; Goto, Y.; Yamada, H.; Mutoh, T.; Komori, A.; Takeiri, Y.; the LHD Experiment Group

2016-04-01

Using ion cyclotron heating and electron cyclotron heating (ECH), or solo ECH, trials of steady state plasma sustainment have been conducted in the superconducting helical/stellarator, large helical device (LHD) (Ida K et al 2015 Nucl. Fusion 55 104018). In recent years, the ECH system has been upgraded by applying newly developed 77 and 154 GHz gyrotrons. A new gas fueling system applied to the steady state operations in the LHD realized precise feedback control of the line average electron density even when the wall condition varied during long pulse discharges. Owing to these improvements in the ECH and the gas fueling systems, a stable 39 min discharge with a line average electron density n e_ave of 1.1  ×  1019 m-3, a central electron temperature T e0 of over 2.5 keV, and a central ion temperature T i0 of 1.0 keV was successfully performed with ~350 kW EC-waves. The parameters are much improved from the previous 65 min discharge with n e_ave of 0.15  ×  1019 m-3 and T e0 of 1.7 keV, and the 30 min discharge with n e_ave of 0.7  ×  1019 m-3 and T e0 of 1.7 keV.

Evaluation of anti-bacterial and anti-oxidant potential of andrographolide and echiodinin isolated from callus culture of Andrographis paniculata Nees

PubMed Central

Arifullah, Mohmmed; Namsa, Nima Dandu; Mandal, Manabendra; Chiruvella, Kishore Kumar; Vikrama, Paritala; Gopal, Ghanta Rama

2013-01-01

Objective To evaluate the anti-bacterial and anti-oxidant activity of andrographolide (AND) and echiodinin (ECH) of Andrographis paniculata. Methods In this study, an attempt has been made to demonstrate the anti-microbial and anti-oxidant activity of isolated AND and ECH by broth micro-dilution method and 2,2-diphenyl-2-picryl-hydrazyl (DPPH) assay, respectively. Structure elucidation was determined by electro-spray ionization-MSD, NMR (1H and 13C) and IR spectra. Results AND was effective against most of the strains tested including Mycobacterium smegmatis, showing broad spectrum of growth inhibition activity with Minimum inhibitory concentration values against Staphylococcus aureus (100 µg/mL), Streptococcus thermophilus (350 µg/mL) Bacillus subtilis (100 µg/mL), Escherichia coli (50 µg/mL), Mycobacterium smegmatis (200 µg/mL), Klebsiella pneumonia (100 µg/mL), and Pseudomonas aeruginosa (200 µg/mL). ECH showed specific anti-bacterial activity against Staphylococcus aureus, Escherichia coli, Bacillus subtilis and Pseudomonas aeruginosa at a concentration higher than 225 µg/mL. Both AND and ECH were not effective against the two yeast strains, Candida albicans and Saccharomyces cerevisiae tested in this study. Conclusion This preliminary study showed promising anti-bacterial activity and moderate free radical scavenging activity of AND and ECH, and it may provide the scientific rationale for its popular folklore medicines. PMID:23905016

Efficient ECH-assisted plasma start-up using trapped particle configuration in the versatile experiment spherical torus

NASA Astrophysics Data System (ADS)

An, YoungHwa; Lee, Jeongwon; Jo, JongGab; Jung, Bong-Ki; Lee, HyunYeong; Chung, Kyoung-Jae; Na, Yong-Su; Hahm, T. S.; Hwang, Y. S.

2017-01-01

An efficient and robust ECH (electron cyclotron heating)-assisted plasma start-up scheme with a low loop voltage and low volt-second consumption utilizing the trapped particle configuration (TPC) has been developed in the versatile experiment spherical torus (VEST). The TPC is a mirror-like magnetic field configuration providing a vertical magnetic field in the same direction as the equilibrium field. It significantly enhances ECH pre-ionization with enhanced particle confinement due to its mirror effect, and intrinsically provides an equilibrium field with a stable decay index enabling prompt plasma current initiation. Consequently, the formation of TPC before the onset of the loop voltage allows the plasma to start up with a lower loop voltage and lower volt-second consumption as well as a wider operation range in terms of ECH pre-ionization power and H2 filling pressure. The TPC can improve the widely-used field null configuration significantly for more efficient start-up when ECH pre-ionization is used. This can then be utilized in superconducting tokamaks requiring a low loop voltage start-up, such as ITER, or in spherical tori with limited volt-seconds. The TPC can be particularly useful in superconducting tokamaks with a limited current slew-rate of superconducting PF coils, as it can save volt-second consumption before plasma current initiation by providing prompt initiation with an intrinsic stable equilibrium field.

Multidisciplinary management of an intra-sellar cavernous hemangioma: Case report and review of the literature.

PubMed

Chibbaro, S; Cebula, H; Ganau, M; Gubian, A; Todeschi, J; Lhermitte, B; Proust, F; Noel, G

2018-06-01

Extra-axial cavernous hemangiomas (ECH) are rare vascular lesions with a tendency to grow within the medial structures of the middle cranial fossa. This pathological entity lacks specific symptoms, and falls into the category of differential diagnosis of space occupying lesions in the cavernous sinus (CS) with or without sellar involvement, including those of tumoral, vascular and inflammatory nature. Of note, ECH can also be indolent, and is at times discovered incidentally during autopsy investigations. On radiological studies, ECH with sellar extension are frequently mistaken at first for pituitary adenomas. Total removal of intrasellar-CS ECH is technically demanding and burdened by remarkable morbidity and mortality rates, mostly related to the complex neuroanatomy of the CS-sellar region (i.e., peri and postoperative bleeding, and transitory or permanent nerve palsies, hormonal deficits). Consequently, only a few cases of successful total removal have been reported so far in the literature. Surgical debulking with cranial nerve decompression followed by stereotactic radiosurgery is currently considered the best alternative to total removal when the latter carries excessive perioperative risks. We present a rare case of a mainly located intrasellar ECH extending to the left CS discussing its clinical features and focusing on the most relevant aspects of the surgical management along with a review of the pertinent literature. Copyright © 2018 Elsevier Ltd. All rights reserved.

Multi-residue determination of 47 organic compounds in water, soil, sediment and fish-Turia River as case study.

PubMed

Carmona, Eric; Andreu, Vicente; Picó, Yolanda

2017-11-30

A sensitive and reliable method based on solid-liquid extraction (SLE) using McIlvaine-Na 2 EDTA buffer (pH=4.5)-methanol and solid-phase extraction (SPE) clean up prior to ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UHPLC-MS/MS) was applied to determine 47 organic contaminants in fish, soil and sediments. The SPE procedure to clean-up the extracts was also used as extraction method to determine these compounds in water. Recoveries ranged from 38 to 104% for all matrices with RSDs<30%. Limits of Quantification for the target compounds were in the range of 10-50ng/g for soil, 2-40ng/g for sediment, 5-30ng/g for fish and 0.3-26ng/L for water. Furthermore, the proposed method was compared to QuEChERS (widely used for environmental matrices) that involves extraction with buffered acetonitrile (pH 5.5) and dispersive SPE clean-up. The results obtained (recoveries>50% for 36 compounds in front of 9, matrix effect<20% for 31 compounds against 21, and LOQs <25ngg -1 for 38 compounds against 22) indicates that the proposed method is more efficient than QuEChERS, The method was applied to monitoring these compounds along the Turia River. In river waters, Paracetamol (175ngL -1 ), ibuprofen (153ngL -1 ) and bisphenol A (41ngL -1 ) were the compounds most frequently detected while in sediments were vildagliptin (7ngg -1 ) and metoprolol (31ngg -1 ) and in fish, bisphenol A (33ngg -1 ) or sulfamethoxazole (13ngg -1 ). Copyright © 2017 Elsevier B.V. All rights reserved.

Dynamically reconfigurable holographic metasurface aperture for a Mills-Cross monochromatic microwave camera.

PubMed

Yurduseven, Okan; Marks, Daniel L; Fromenteze, Thomas; Smith, David R

2018-03-05

We present a reconfigurable, dynamic beam steering holographic metasurface aperture to synthesize a microwave camera at K-band frequencies. The aperture consists of a 1D printed microstrip transmission line with the front surface patterned into an array of slot-shaped subwavelength metamaterial elements (or meta-elements) dynamically tuned between "ON" and "OFF" states using PIN diodes. The proposed aperture synthesizes a desired radiation pattern by converting the waveguide-mode to a free space radiation by means of a binary modulation scheme. This is achieved in a holographic manner; by interacting the waveguide-mode (reference-wave) with the metasurface layer (hologram layer). It is shown by means of full-wave simulations that using the developed metasurface aperture, the radiated wavefronts can be engineered in an all-electronic manner without the need for complex phase-shifting circuits or mechanical scanning apparatus. Using the dynamic beam steering capability of the developed antenna, we synthesize a Mills-Cross composite aperture, forming a single-frequency all-electronic microwave camera.

Optimisation of active suspension control inputs for improved vehicle handling performance

NASA Astrophysics Data System (ADS)

Čorić, Mirko; Deur, Joško; Kasać, Josip; Tseng, H. Eric; Hrovat, Davor

2016-11-01

Active suspension is commonly considered under the framework of vertical vehicle dynamics control aimed at improvements in ride comfort. This paper uses a collocation-type control variable optimisation tool to investigate to which extent the fully active suspension (FAS) application can be broaden to the task of vehicle handling/cornering control. The optimisation approach is firstly applied to solely FAS actuator configurations and three types of double lane-change manoeuvres. The obtained optimisation results are used to gain insights into different control mechanisms that are used by FAS to improve the handling performance in terms of path following error reduction. For the same manoeuvres the FAS performance is compared with the performance of different active steering and active differential actuators. The optimisation study is finally extended to combined FAS and active front- and/or rear-steering configurations to investigate if they can use their complementary control authorities (over the vertical and lateral vehicle dynamics, respectively) to further improve the handling performance.

Phased array performance evaluation with photoelastic visualization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ginzel, Robert; Dao, Gavin

2014-02-18

New instrumentation and a widening range of phased array transducer options are affording the industry a greater potential. Visualization of the complex wave components using the photoelastic system can greatly enhance understanding of the generated signals. Diffraction, mode conversion and wave front interaction, together with beam forming for linear, sectorial and matrix arrays, will be viewed using the photoelastic system. Beam focus and steering performance will be shown with a range of embedded and surface targets within glass samples. This paper will present principles and sound field images using this visualization system.

A Low-Power CMOS Front-End for Photoplethysmographic Signal Acquisition With Robust DC Photocurrent Rejection.

PubMed

Wong, A K Y; Kong-Pang Pun; Yuan-Ting Zhang; Ka Nang Leung

2008-12-01

A micro-power CMOS front-end, consisting of a transimpedance amplifier (TIA) and an ultralow cutoff frequency lowpass filter for the acquisition of photoplethysmographic signal (PPG) is presented. Robust DC photocurrent rejection for the pulsed signal source is achieved through a sample-and-hold stage in the feed-forward signal path and an error amplifier in the feedback path. Ultra-low cutoff frequency of the filter is achieved with a proposed technique that incorporates a pair of current-steering transistors that increases the effective filter capacitance. The design was realized in a 0.35-mum CMOS technology. It consumes 600 muW at 2.5 V, rejects DC photocurrent ranged from 100 nA to 53.6 muA, and achieves lower-band and upper-band - 3-dB cutoff frequencies of 0.46 and 2.8 Hz, respectively.

Effects of temperature and purity of magnesium sulfate during extraction of pesticides residues using the QuEChERS method

USDA-ARS?s Scientific Manuscript database

Despite its many documented advantages, the QuEChERS (quick, easy, cheap, effective, rugged and safe) sample preparation approach has problems with a few unstable pesticides, partly due to the exothermic reaction generated by the use of anhydrous magnesium sulfate during extraction. These pesticide...

Evolution of the radial electric field in high-Te ECH heated plasmas on LHD

NASA Astrophysics Data System (ADS)

Pablant, Novimir; Bitter, Manfred; Delgado Aparicio, Luis F.; Dinklage, Andreas; Gates, David; Goto, Motoshi; Ido, Takeshi; Hill, Kenneth H.; Kubo, Shin; Morita, Shigeru; Nagaoka, Kenichi; Oishi, Tetsutarou; Satake, Shinsuke; Takahashi, Hiromi; Yokoyama, Masayuki; LHD Experiment Group Team

2014-10-01

A detailed study is presented on the evolution of the radial electric field (Er) under a range of densities and injected ECH powers on the Large Helical Device (LHD). These plasmas focused on high-electron temperature ECH heated plasmas which exhibit a transition of Er from the ion-root to the electron-root when either the density is reduced or the ECH power is increased. Measurements of poloidal rotation were achieved using the X-Ray Imaging Crystal Spectrometer (XICS) and are compared with neo-classical predictions of the radial electric field using the GSRAKE and FORTEC-3D codes. This study is based on a series of experiments on LHD which used fast modulation of the gyrotrons on LHD to produce a detailed power scan with a constant power deposition profile. This is a novel application of this technique to LHD, and has provided the most detailed study to date on dependence of the radial electric field on the injected power. Detailed scans of the density at constant injected power were also made, allowing a separation of the power and density dependence.

Superthermal Electron Magnetosphere-Ionosphere Coupling in the Diffuse Aurora in the Presence of ECH Waves

NASA Technical Reports Server (NTRS)

Khazanov, G. V.; Tripathi, A. K.; Singhal, R. P.; Himwich, Elizabeth; Glocer, A.; Sibeck, D. G.

2015-01-01

There are two main theories for the origin of the diffuse auroral electron precipitation: first, pitch angle scattering by electrostatic electron cyclotron harmonic (ECH) waves, and second, by whistler mode waves. Precipitating electrons initially injected from the plasma sheet to the loss cone via wave-particle interaction processes degrade in the atmosphere toward lower energies and produce secondary electrons via impact ionization of the neutral atmosphere. These secondary electrons can escape back to the magnetosphere, become trapped on closed magnetic field lines, and deposit their energy back to the inner magnetosphere. ECH and whistler mode waves can also move electrons in the opposite direction, from the loss cone into the trap zone, if the source of such electrons exists in conjugate ionospheres located at the same field lines as the trapped magnetospheric electron population. Such a situation exists in the simulation scenario of superthermal electron energy interplay in the region of diffuse aurora presented and discussed by Khazanov et al. (2014) and will be quantified in this paper by taking into account the interaction of secondary electrons with ECH waves.

Evaluation of operating conditions for sustainable harvesting of microalgal biomass applying electrochemical method using non sacrificial electrodes.

PubMed

Misra, Rohit; Guldhe, Abhishek; Singh, Poonam; Rawat, Ismail; Stenström, Thor Axel; Bux, Faizal

2015-01-01

The efficient harvesting of microalgae is considered to be one of the challenging steps of algal biofuel production and a key factor limiting the commercial use of microalgae. To overcome the limitation of metallic electrodes depletion, the application of non-sacrificial electrode was investigated for the electrochemical harvesting (ECH) of microalgae. The effect of applied current, addition of electrolyte and initial pH were parameters investigated. The highest recovery efficiency of 83% was obtained for Scenedesmus obliquus at 1.5A, initial pH 9 and 6gL(-)(1) NaCl with power consumption of 3.84kWhkg(-)(1). Recovery efficiency of ECH process was comparable to literature reported centrifugation, filtration and chemical flocculation techniques but with a much lower power consumption. The ECH process with addition of electrolyte enhanced the lipid extraction by 22% without any adverse effects. The ECH process with non sacrificial carbon electrodes could be a possible harvesting step at commercial scale microalgal biomass production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Synthesis of diethylaminoethyl dextran hydrogel and its heavy metal ion adsorption characteristics.

PubMed

Demirbilek, Celile; Dinç, Cemile Özdemir

2012-10-01

Epichlorohydrin-crosslinked diethylaminoethyl dextran (DEAE-D/ECH) hydrogel was synthesized by intermolecular side-chain reaction of DEAE-D hydroxyl groups with monomeric crosslinking agent, ECH. Swelling ability, adsorption capacity and metal removal of the hydrogel were profoundly determined and some structural parameters for the hydrogel such as volume of non-swollen gel, percentages of gellation, swelling ratio and equilibrium water content were evaluated in this study. The ability of removing heavy metal ions from Orontes River by the synthesized hydrogel, thoroughly characterized by photometric spectrometer and the adsorption characteristics of metal ions, was investigated as well as surface morphologies of the hydrogel before and after metal adsorption were examined by SEM. Structure of DEAE-D/ECH gel was analyzed by FTIR, TGA, and DSC. Gellation point of binary system reaction between DEAE-D and ECH was determined via monitoring viscosity changes during reaction. The order of affinity based on amount of metal ion uptake was found as follows: Zn(2+)>Mn(2+)>Pb(2+)>Cd(2+). Copyright © 2012 Elsevier Ltd. All rights reserved.

Combination of QuEChERS and DLLME for GC-MS determination of pesticide residues in orange samples.

PubMed

Andraščíková, Mária; Hrouzková, Svetlana; Cunha, Sara C

2013-01-01

A new method combining QuEChERS (quick, easy, cheap, effective, rugged and safe) and DLLME (dispersive liquid-liquid microextraction) followed by gas chromatography-mass spectrometry with selected ion monitoring (SIM) was developed for the simultaneous determination of 19 pesticides from nine chemical groups exhibiting or suspected to exhibit endocrine-disrupting properties in orange samples. Acetonitrile extract obtained from QuEChERS extraction was used for DLLME as dispersive solvent and carbon tetrachloride as extractive solvent to increase the enrichment factor of the extraction procedure. The effect of several extraction parameters, such as volume extract achieved by the QuEChERS method and subsequently used for DLLME, selection of extractive solvent and its volume, was tested. Under optimum conditions, good linearity, satisfactory recoveries and repeatability were obtained. Limits of quantification (LOQs) achieved (ranging from 0.02 to 47 ng/g) were below the maximum residue limits established by the European Union. The proposed method was applied to the monitoring of pesticide residue levels in oranges commercialised in Portugal.

Inexpensive, effective novel activated carbon fibers for sample cleanup: application to multipesticide residue analysis in food commodities using a QuEChERS method.

PubMed

Singh, Shiv; Srivastava, Anshuman; Singh, Sheelendra Pratap

2018-03-01

Phenolic resin based activated carbon fibers (ACFs) were applied for the first time as a reversed-dispersive solid-phase extraction (r-DSPE) sorbent. A modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) method was applied to determine 26 pesticides (organophosphates, organochlorines, synthetic pyrethroids, and herbicides) in different complex matrices, including cauliflower, cucumber, banana, apple, wheat, and black gram. Different physicochemical characterization techniques were used to investigate the engineering and structural properties of the r-DSPE sorbent. All the chromatographic analyses were performed with a gas chromatograph equipped with an electron capture detector. The recoveries of all 26 pesticides were acceptable (70-120%), with relative standard deviations of less than 15%. The limit of detection and the limit of quantification were 1.13-5.48 ng/g and 3.42-16.60 ng/g, respectively. In the original QuEChERS method, primary secondary amine is extensively used as the r-DSPE sorbent in the cleanup process, but it is eightfold more expensive than the ACFs used in this study. Therefore, the modified QuEChERS method using ACFs during the cleanup process is more efficient, cheaper, and more robust to determine pesticides from different types of matrices, including vegetables, grains, and fruits, and ACFs could be used as a cost-effective alternative to primary secondary amine. Graphical Abstract Sample clean-up using PSA and ACF as r-DSPE sorbent in QuEChERS method.

Mechanistic principles of colloidal crystal growth by evaporation-induced convective steering.

PubMed

Brewer, Damien D; Allen, Joshua; Miller, Michael R; de Santos, Juan M; Kumar, Satish; Norris, David J; Tsapatsis, Michael; Scriven, L E

2008-12-02

We simulate evaporation-driven self-assembly of colloidal crystals using an equivalent network model. Relationships between a regular hexagonally close-packed array of hard, monodisperse spheres, the associated pore space, and selectivity mechanisms for face-centered cubic microstructure propagation are described. By accounting for contact line rearrangement and evaporation at a series of exposed menisci, the equivalent network model describes creeping flow of solvent into and through a rigid colloidal crystal. Observations concerning colloidal crystal growth are interpreted in terms of the convective steering hypothesis, which posits that solvent flow into and through the pore space of the crystal may play a major role in colloidal self-assembly. Aspects of the convective steering and deposition of high-Peclet-number rigid spherical particles at a crystal boundary are inferred from spatially resolved solvent flow into the crystal. Gradients in local flow through boundary channels were predicted due to the channels' spatial distribution relative to a pinned free surface contact line. On the basis of a uniform solvent and particle flux as the criterion for stability of a particular growth plane, these network simulations suggest the stability of a declining {311} crystal interface, a symmetry plane which exclusively propagates fcc microstructure. Network simulations of alternate crystal planes suggest preferential growth front evolution to the declining {311} interface, in consistent agreement with the proposed stability mechanism for preferential fcc microstructure propagation in convective assembly.

Multi-residue methods for the determination of over four hundred pesticides in solid and liquid high sucrose content matrices by tandem mass spectrometry coupled with gas and liquid chromatograph.

PubMed

Lozowicka, Bozena; Ilyasova, Gulzhakhan; Kaczynski, Piotr; Jankowska, Magdalena; Rutkowska, Ewa; Hrynko, Izabela; Mojsak, Patrycja; Szabunko, Julia

2016-05-01

For the first time three methods: matrix solid phase dispersion (MSPD), original and modified QuEChERS, with and without clean up step were studied in order to evaluate the extraction efficiency of various classes of pesticides from solid and liquid high sucrose content matrices. Determinations over four hundred pesticides were performed by gas and liquid chromatography with triple quadrupole mass spectrometry (GC/LC/MS/MS) using multiple reaction monitoring. The proposed methods were validated on sugar beets and their technological product beet molasses. In general, the recoveries obtained for the original QuEChERS and MSPD method were lower (<70%) than for the modified QuEChERS without clean up in sugar beet and with clean up in beet molasses. Among these methods, high extraction yields were achieved as recommended in SANCO/12571/2013, with repeatability of 4.4-19.2% and within-laboratory reproducibility of 7.1-18.4% for citrate QuEChERS, whereas greater ruggedness were observed for MSPD. The limit of quantification (LOQ) at (the lowest MRL=0.01mgkg(-1)e.g. for oxamyl()) or below (0.005mgkg(-1)) the regulatory maximum residue level for the pesticides were achieved. The expanded measurement uncertainty was not higher than 30% for all target analytes. Matrix effects were compared and observed for both matrices at both gas and liquid chromatography. The most compounds showed signal enhancement and it was compensated by using matrix-matched calibration and modified QuEChERS characterized lower matrix effects. The confirmation of suitability citrate QuEChERS optimized method was to use for routine testing of several dozen samples determination and residue of epoxiconazole and tebuconazole (both at 0.01mgkg(-1)) in the samples of beet molasses and cyfluthrin (0.06mgkg(-1)) in sugar beet were found. Copyright © 2016 Elsevier B.V. All rights reserved.

Electron cyclotron heating can drastically alter reversed shear Alfvén eigenmode activity in DIII-D through finite pressure effects

NASA Astrophysics Data System (ADS)

Van Zeeland, M. A.; Heidbrink, W. W.; Sharapov, S. E.; Spong, D.; Cappa, A.; Chen, Xi; Collins, C.; García-Muñoz, M.; Gorelenkov, N. N.; Kramer, G. J.; Lauber, P.; Lin, Z.; Petty, C.

2016-11-01

A recent DIII-D experiment investigating the impact of electron cyclotron heating (ECH) on neutral beam driven reversed shear Alfvén eigenmode (RSAE) activity is presented. The experiment includes variations of ECH injection location and timing, current ramp rate, beam injection geometry (on/off-axis), and neutral beam power. Essentially all variations carried out in this experiment were observed to change the impact of ECH on AE activity significantly. In some cases, RSAEs were observed to be enhanced with ECH near the off-axis minimum in magnetic safety factor ({{q}\\min} ), in contrast to the original DIII-D experiments where the modes were absent when ECH was deposited near {{q}\\min} . It is found that during intervals when the geodesic acoustic mode (GAM) frequency at {{q}\\min} is elevated and the calculated RSAE minimum frequency, including contributions from thermal plasma gradients, is very near or above the nominal TAE frequency (f TAE), RSAE activity is not observed or RSAEs with a much reduced frequency sweep range are found. This condition is primarily brought about by ECH modification of the local electron temperature (T e) which can raise both the local T e at {{q}\\min} as well as its gradient. A q-evolution model that incorporates this reduction in RSAE frequency sweep range is in agreement with the observed spectra and appears to capture the relative balance of TAE or RSAE-like modes throughout the current ramp phase of over 38 DIII-D discharges. Detailed ideal MHD calculations using the NOVA code show both modification of plasma pressure and pressure gradient at {{q}\\min} play an important role in modifying the RSAE activity. Analysis of the ECH injection near the {{q}\\min} case where no frequency sweeping RSAEs are observed shows the typical RSAE is no longer an eigenmode of the system. What remains is an eigenmode with poloidal harmonic content reminiscent of the standard RSAE, but absent of the typical frequency sweeping behavior. The remaining eigenmode is also often strongly coupled to gap TAEs. Analysis with the non-perturbative gyro fluid code TAEFL confirms this change in RSAE activity and also shows a large drop in the resultant mode growth rates.

Electron cyclotron heating can drastically alter reversed shear Alfvén eigenmode activity in DIII-D through finite pressure effects

DOE PAGES

Van Zeeland, M. A.; Heidbrink, W. W.; Sharapov, S. E.; ...

2016-07-22

Here, a recent DIII-D experiment investigating the impact of electron cyclotron heating (ECH) on neutral beam driven reversed shear Alfvén eigenmode (RSAE) activity is presented. The experiment includes variations of ECH injection location and timing, current ramp rate, beam injection geometry (on/off-axis), and neutral beam power. Essentially all variations carried out in this experiment were observed to change the impact of ECH on AE activity significantly. In some cases, RSAEs were observed to be enhanced with ECH near the off-axis minimum in magnetic safety factor (more » $${{q}_{\\min}}$$ ), in contrast to the original DIII-D experiments where the modes were absent when ECH was deposited near $${{q}_{\\min}}$$ . It is found that during intervals when the geodesic acoustic mode (GAM) frequency at $${{q}_{\\min}}$$ is elevated and the calculated RSAE minimum frequency, including contributions from thermal plasma gradients, is very near or above the nominal TAE frequency (f TAE), RSAE activity is not observed or RSAEs with a much reduced frequency sweep range are found. This condition is primarily brought about by ECH modification of the local electron temperature (T e) which can raise both the local T e at $${{q}_{\\min}}$$ as well as its gradient. A q-evolution model that incorporates this reduction in RSAE frequency sweep range is in agreement with the observed spectra and appears to capture the relative balance of TAE or RSAE-like modes throughout the current ramp phase of over 38 DIII-D discharges. Detailed ideal MHD calculations using the NOVA code show both modification of plasma pressure and pressure gradient at $${{q}_{\\min}}$$ play an important role in modifying the RSAE activity. Analysis of the ECH injection near the $${{q}_{\\min}}$$ case where no frequency sweeping RSAEs are observed shows the typical RSAE is no longer an eigenmode of the system. What remains is an eigenmode with poloidal harmonic content reminiscent of the standard RSAE, but absent of the typical frequency sweeping behavior. The remaining eigenmode is also often strongly coupled to gap TAEs. Analysis with the non-perturbative gyro fluid code TAEFL confirms this change in RSAE activity and also shows a large drop in the resultant mode growth rates.« less

EChO. Exoplanet characterisation observatory

NASA Astrophysics Data System (ADS)

Tinetti, G.; Beaulieu, J. P.; Henning, T.; Meyer, M.; Micela, G.; Ribas, I.; Stam, D.; Swain, M.; Krause, O.; Ollivier, M.; Pace, E.; Swinyard, B.; Aylward, A.; van Boekel, R.; Coradini, A.; Encrenaz, T.; Snellen, I.; Zapatero-Osorio, M. R.; Bouwman, J.; Cho, J. Y.-K.; Coudé de Foresto, V.; Guillot, T.; Lopez-Morales, M.; Mueller-Wodarg, I.; Palle, E.; Selsis, F.; Sozzetti, A.; Ade, P. A. R.; Achilleos, N.; Adriani, A.; Agnor, C. B.; Afonso, C.; Allende Prieto, C.; Bakos, G.; Barber, R. J.; Barlow, M.; Batista, V.; Bernath, P.; Bézard, B.; Bordé, P.; Brown, L. R.; Cassan, A.; Cavarroc, C.; Ciaravella, A.; Cockell, C.; Coustenis, A.; Danielski, C.; Decin, L.; De Kok, R.; Demangeon, O.; Deroo, P.; Doel, P.; Drossart, P.; Fletcher, L. N.; Focardi, M.; Forget, F.; Fossey, S.; Fouqué, P.; Frith, J.; Galand, M.; Gaulme, P.; Hernández, J. I. González; Grasset, O.; Grassi, D.; Grenfell, J. L.; Griffin, M. J.; Griffith, C. A.; Grözinger, U.; Guedel, M.; Guio, P.; Hainaut, O.; Hargreaves, R.; Hauschildt, P. H.; Heng, K.; Heyrovsky, D.; Hueso, R.; Irwin, P.; Kaltenegger, L.; Kervella, P.; Kipping, D.; Koskinen, T. T.; Kovács, G.; La Barbera, A.; Lammer, H.; Lellouch, E.; Leto, G.; Lopez Morales, M.; Lopez Valverde, M. A.; Lopez-Puertas, M.; Lovis, C.; Maggio, A.; Maillard, J. P.; Maldonado Prado, J.; Marquette, J. B.; Martin-Torres, F. J.; Maxted, P.; Miller, S.; Molinari, S.; Montes, D.; Moro-Martin, A.; Moses, J. I.; Mousis, O.; Nguyen Tuong, N.; Nelson, R.; Orton, G. S.; Pantin, E.; Pascale, E.; Pezzuto, S.; Pinfield, D.; Poretti, E.; Prinja, R.; Prisinzano, L.; Rees, J. M.; Reiners, A.; Samuel, B.; Sánchez-Lavega, A.; Forcada, J. Sanz; Sasselov, D.; Savini, G.; Sicardy, B.; Smith, A.; Stixrude, L.; Strazzulla, G.; Tennyson, J.; Tessenyi, M.; Vasisht, G.; Vinatier, S.; Viti, S.; Waldmann, I.; White, G. J.; Widemann, T.; Wordsworth, R.; Yelle, R.; Yung, Y.; Yurchenko, S. N.

2012-10-01

A dedicated mission to investigate exoplanetary atmospheres represents a major milestone in our quest to understand our place in the universe by placing our Solar System in context and by addressing the suitability of planets for the presence of life. EChO—the Exoplanet Characterisation Observatory—is a mission concept specifically geared for this purpose. EChO will provide simultaneous, multi-wavelength spectroscopic observations on a stable platform that will allow very long exposures. The use of passive cooling, few moving parts and well established technology gives a low-risk and potentially long-lived mission. EChO will build on observations by Hubble, Spitzer and ground-based telescopes, which discovered the first molecules and atoms in exoplanetary atmospheres. However, EChO's configuration and specifications are designed to study a number of systems in a consistent manner that will eliminate the ambiguities affecting prior observations. EChO will simultaneously observe a broad enough spectral region—from the visible to the mid-infrared—to constrain from one single spectrum the temperature structure of the atmosphere, the abundances of the major carbon and oxygen bearing species, the expected photochemically-produced species and magnetospheric signatures. The spectral range and resolution are tailored to separate bands belonging to up to 30 molecules and retrieve the composition and temperature structure of planetary atmospheres. The target list for EChO includes planets ranging from Jupiter-sized with equilibrium temperatures T eq up to 2,000 K, to those of a few Earth masses, with T eq u223c 300 K. The list will include planets with no Solar System analog, such as the recently discovered planets GJ1214b, whose density lies between that of terrestrial and gaseous planets, or the rocky-iron planet 55 Cnc e, with day-side temperature close to 3,000 K. As the number of detected exoplanets is growing rapidly each year, and the mass and radius of those detected steadily decreases, the target list will be constantly adjusted to include the most interesting systems. We have baselined a dispersive spectrograph design covering continuously the 0.4-16 μm spectral range in 6 channels (1 in the visible, 5 in the InfraRed), which allows the spectral resolution to be adapted from several tens to several hundreds, depending on the target brightness. The instrument will be mounted behind a 1.5 m class telescope, passively cooled to 50 K, with the instrument structure and optics passively cooled to u223c45 K. EChO will be placed in a grand halo orbit around L2. This orbit, in combination with an optimised thermal shield design, provides a highly stable thermal environment and a high degree of visibility of the sky to observe repeatedly several tens of targets over the year. Both the baseline and alternative designs have been evaluated and no critical items with Technology Readiness Level (TRL) less than 4-5 have been identified. We have also undertaken a first-order cost and development plan analysis and find that EChO is easily compatible with the ESA M-class mission framework.

Residue analysis of sixty pesticides in red swamp crayfish using QuEChERS with high-performance liquid chromatography-tandem mass spectrometry

USDA-ARS?s Scientific Manuscript database

In this study, a multi-residue analytical method using QuEChERS extraction and dispersive solid-phase extraction (d-SPE) cleanup followed by high-performance liquid chromatography–tandem mass spectrometry (HPLC-MS/MS) was developed for rapid determination of 60 pesticide residues in whole crayfish a...

QuEChERS, a sample preparation technique that is “catching on”: an up-to-date interview with its inventors

USDA-ARS?s Scientific Manuscript database

The technique of QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) is only 7 years old, yet it is revolutionizing the manner in which multiresidue, multiclass pesticide analysis (and perhaps beyond) is performed. Columnist Ron Majors sits down with inventors Steve Lehotay and Michelangelo An...

Determination of sulfonamides in animal tissues by modified QuEChERS and liquid chromatography tandem mass spectrometry.

PubMed

Wen, Ching-Hsuan; Lin, Shu-Ling; Fuh, Ming-Ren

2017-03-01

In this study, the salting-out solvent extraction and dispersive solid-phase extraction (dSPE) clean-up steps in QuEChERS (quick, easy, cheap, effective, rugged, and safe) method were optimized to reduce matrix effect and efficiently extract target sulfonamides from a variety of edible animal tissues. The extracted sulfonamides were then analyzed using liquid chromatography tandem mass spectrometry (LC-MS/MS). Good extraction recoveries (74.0-100.3% in five different sources of animal tissues; n=3) with acceptable matrix effect (<10%, except for liver samples) were obtained using the proposed method. For the first time, a commercial ND-lipids cartridge was used to remove hydrophobic matrix components from fat-rich animal tissues in the clean-up step of QuEChERS. In addition, good linearity (0.125-12.5ngg -1 ) was observed using matrix-matched calibration (in beef). Limits of detection (LODs) were estimated at 0.01-0.03ngg -1 in beef, pork, and chicken samples. For beef tripe and pig liver samples, the LODs were in the range of 0.02-0.04ngg -1 . Good intra-day/inter-day precision (1.0-10.5%/0.4-8.0%) and accuracy (95.2-107.2%/97.8-102.1%) were also achieved using the modified QuEChERS for sample pretreatment. The applicability of the modified QuEChERS-LC-MS/MS method was demonstrated by determining the occurrence of target sulfonamides in various edible animal tissues for potential food safety analysis. Copyright © 2016 Elsevier B.V. All rights reserved.

Resolution and some properties of enzymes involved in enantioselective transformation of 1,3-dichloro-2-propanol to (R)-3-chloro-1,2-propanediol by Corynebacterium sp. strain N-1074.

PubMed Central

Nakamura, T; Nagasawa, T; Yu, F; Watanabe, I; Yamada, H

1992-01-01

During the course of the transformation of 1,3-dichloro-2-propanol (DCP) into (R)-3-chloro-1,2-propanediol [(R)-MCP] with the cell extract of Corynebacterium sp. strain N-1074, epichlorohydrin (ECH) was transiently formed. The cell extract was fractionated into two DCP-dechlorinating activities (fractions Ia and Ib) and two ECH-hydrolyzing activities (fractions IIa and IIb) by TSKgel DEAE-5PW column chromatography. Fractions Ia and Ib catalyzed the interconversion of DCP to ECH, and fractions IIa and IIb catalyzed the transformation of ECH into MCP. Fractions Ia and IIa showed only low enantioselectivity for each reaction, whereas fractions Ib and IIb exhibited considerable enantioselectivity, yielding R-rich ECH and MCP, respectively. Enzymes Ia and Ib were isolated from fractions Ia and Ib, respectively. Enzyme Ia had a molecular mass of about 108 kDa and consisted of four subunits identical in molecular mass (about 28 kDa). Enzyme Ib was a protein of 115 kDa, composed of two different polypeptides (about 35 and 32 kDa). The specific activity of enzyme Ib for DCP was about 30-fold higher than that of enzyme Ia. Both enzymes catalyzed the transformation of several halohydrins into the corresponding epoxides with liberation of halides and its reverse reaction. Their substrate specificities and immunological properties differed from each other. Enzyme Ia seemed to be halohydrin hydrogen-halide-lyase which was already purified from Escherichia coli carrying a gene from Corynebacterium sp. strain N-1074. Images PMID:1447132

"It's Like Giving Us a Car, Only without the Wheels": A Critical Policy Analysis of an Early College Programme

ERIC Educational Resources Information Center

Locke, Leslie Ann; McKenzie, Kathryn Bell

2016-01-01

The purpose of this qualitative inquiry was to examine the perceptions and experiences of Latina students, who were underperforming in an early college high school (ECHS), regarding their achievement and experiences. Additionally, the school's institutional documents were used to critically assess the viability of the ECHS as an equity-oriented,…

Microwave plasma source for neutral-beam injection systems

NASA Astrophysics Data System (ADS)

1981-08-01

The overall program is described and the technical and programmatic reasons for the decision to pursue both the RFI and ECH sources into the current hydrogen test stage is discussed. The general characteristics of plasma sources in the parameter regime of interest for neutral beam applications are considered. The operational characteristics, advantages and potential problems of RFI and ECH sources are discussed.

Determination of six parabens residues in fresh-cut vegetables using QuEChERS with multi-walled carbon nanotubes and high performance liquid chromatography-tandem mass spectrometry

USDA-ARS?s Scientific Manuscript database

In this study, an optimized QuEChERS sample preparation method was developed to analyze residues of six parabens: methyl-, ethyl-, n-propyl-, isopropyl-, n-butyl-, and isobutyl-paraben in five fresh-cut vegetables (potato, broccoli, carrot, celery and cabbage) with high performance liquid chromatogr...

The membrane-bound [NiFe]-hydrogenase (Ech) from Methanosarcina barkeri: unusual properties of the iron-sulphur clusters.

PubMed

Kurkin, Sergei; Meuer, Jörn; Koch, Jürgen; Hedderich, Reiner; Albracht, Simon P J

2002-12-01

The purified membrane-bound [NiFe]-hydrogenase from Methanosarcina barkeri was studied with electron paramagnetic resonance (EPR) focusing on the properties of the iron-sulphur clusters. The EPR spectra showed signals from three different [4Fe-4S] clusters. Two of the clusters could be reduced under 101 kPa of H2, whereas the third cluster was only partially reduced. Magnetic interaction of one of the clusters with an unpaired electron localized on the Ni-Fe site indicated that this was the proximal cluster as found in all [NiFe]-hydrogenases. Hence, this cluster was assigned to be located in the EchC subunit. The other two clusters could therefore be assigned to be bound to the EchF subunit, which has two conserved four-Cys motifs for the binding of a [4Fe-4S] cluster. Redox titrations at different pH values demonstrated that the proximal cluster and one of the clusters in the EchF subunit had a pH-dependent midpoint potential. The possible relevance of these properties for the function of this proton-pumping [NiFe]-hydrogenase is discussed.

[Poldi-Čech cemented femoral stem in total hip arthroplasty after 25 years].

PubMed

Rozkydal, Z; Janíček, P

2010-08-01

The aim of the study was to evaluate the results of Poldi-Čech femoral stem implantation in primary total hip arthroplasty after 25 years. A group of 65 patients (90 hips) with Poldi-Čech total hip arthroplasty carried out between 1974 and 1984 was evaluated at the end of 2009. The mean follow-up of all patients was 28 years (25 to 35). There were seven men and 58 women. The mean age at the time of implantation was 43 years (26 to 60) and at the latest follow-up it was 72 years. In all patients the cemented UHMW PE acetabular component (RCH 1000) was used together with AKV Ultra 2 Poldi steel femoral stems (1st, 2nd and 3rd generations). The stem was a monoblock with a 32-mm head. The evaluation of the results was based on the Harris hip score and X ray with an A-P view of the pelvis and the affected hip. Statistical analysis was made using the life-table method. At the latest follow up the mean Harris score was 69.7 points (40 to 88). There were 69 hips with an original Poldi-Čech femoral component still in situ, 64 of them were stable and five with radiological evidence of aseptic loosening. Five patients had undergone Girdlestone resection arthroplasty for septic loosening. Thirteen patients (16 hips) had femoral stem revision. The cumulative proportion of clinical survivorship of the Poldi-Čech femoral stem, with revision for any reason as the endpoint, .was 0.93 at 6 years, 0.84 at 12 years, and 0.77 at 18, 24 and 30 years after the index surgery. Radiographic findings revealed 64 hips with stable stems, five hips with ;aseptic loosening (probable, 0 possible, 2, definite, 3). Six- teen hips were after revision surgery for aseptic loosening of the stem and five hips were after Girdlestone resection arthroplasty for septic failure. The cumulative proportion of radiological survivorship of the Poldi-Čech femoral stem with any reason as the endpoint was 0.92 at 6 years, 0.78 at 12 years, 0.72 at 18 years, 0.69 at 24 years and 0.69 at 30 years. The Poldi-Čech stem with its anatomical shape and a highly polished surface meets the principles of successful composite beam stems. Its disadvantage is a valgus neck- shaft angle of 140° giving lower femoral offset and the risk of development of valgus deformity of the ipsilateral knee. In most cases osteolysis, radiolucent lines and bone rarefaction of the femur resulted from polyethylene wear of the acetabular component. This study demonstrates a long-term survivorship of the Poldi-Čech femoral component in patients undergoing total hip arthroplasty 25 to 35 years ago.

Stability enhancement and fuel economy of the 4-wheel-drive hybrid electric vehicles by optimal tyre force distribution

NASA Astrophysics Data System (ADS)

Goodarzi, Avesta; Mohammadi, Masoud

2014-04-01

In this paper, vehicle stability control and fuel economy for a 4-wheel-drive hybrid vehicle are investigated. The integrated controller is designed within three layers. The first layer determines the total yaw moment and total lateral force made by using an optimal controller method to follow the desired dynamic behaviour of a vehicle. The second layer determines optimum tyre force distribution in order to optimise tyre usage and find out how the tyres should share longitudinal and lateral forces to achieve a target vehicle response under the assumption that all four wheels can be independently steered, driven, and braked. In the third layer, the active steering, wheel slip, and electrical motor torque controllers are designed. In the front axle, internal combustion engine (ICE) is coupled to an electric motor (EM). The control strategy has to determine the power distribution between ICE and EM to minimise fuel consumption and allowing the vehicle to be charge sustaining. Finally, simulations performed in MATLAB/SIMULINK environment show that the proposed structure could enhance the vehicle stability and fuel economy in different manoeuvres.

Pesticide Multiresidue Analysis in Cereal Grains Using Modified QuEChERS Method Combined with Automated Direct Sample Introduction GC-TOFMS and UPLC-MS/MS Techniques

USDA-ARS?s Scientific Manuscript database

The QuEChERS (quick, easy, cheap, effective, rugged, and safe) sample preparation method was modified to accommodate various cereal grain matrices (corn, oat, rice and wheat) and provide good analytical results (recoveries in the range of 70-120% and RSDs <20%) for the majority of the target pestici...

Hydrogenation of benzaldehyde via electrocatalysis and thermal catalysis on carbon-supported metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Yang; Sanyal, Udishnu; Pangotra, Dhananjai

Abstract Selective reduction of benzaldehyde to benzyl alcohol on C-supported Pt, Rh, Pd, and Ni in aqueous phase was conducted using either directly H2 (thermal catalytic hydrogenation, TCH) or in situ electrocatalytically generated hydrogen (electrocatalytic hydrogenation, ECH). In TCH, the intrinsic activity of the metals at room temperature and 1 bar H2 increased in the sequence Rh/C < Pt/C < Pd/C, while Ni/C is inactive at these conditions due to surface oxidation in the absence of cathodic potential. The reaction follows a Langmuir-Hinshelwood mechanism with the second hydrogen addition to the adsorbed hydrocarbon being the rate-determining step. All tested metalsmore » were active in ECH of benzaldehyde, although hydrogenation competes with the hydrogen evolution reaction (HER). The minimum cathodic potentials to obtain appreciable ECH rates were identical to the onset potentials of HER. Above this onset, the relative rates of H reacting to H2 and H addition to the hydrocarbon determines the selectivity to ECH and TCH. Accordingly, the selectivity of the metals towards ECH increases in the order Ni/C < Pt/C < Rh/C < Pd/C. Pd/C shows exceptionally high ECH selectivity due to its surprisingly low HER reactivity under the reaction conditions. Acknowledgements The authors would like to thank the groups of Hubert A. Gasteiger at the Technische Universität München of Jorge Gascon at the Delft University of Technology for advice and valuable discussions. The authors are grateful to Nirala Singh, Erika Ember, Gary Haller, and Philipp Rheinländer for fruitful discussions. We are also grateful to Marianne Hanzlik for TEM measurements and to Xaver Hecht and Martin Neukamm for technical support. Y.S. would like to thank the Chinese Scholarship Council for the financial support. The research described in this paper is part of the Chemical Transformation Initiative at Pacific Northwest National Laboratory (PNNL), conducted under the Laboratory Directed Research and Development Program at PNNL, a multiprogram national laboratory operated by Battelle for the U.S. Department of Energy.« less

Cold-induced aqueous acetonitrile phase separation: A salt-free way to begin quick, easy, cheap, effective, rugged, safe.

PubMed

Shao, Gang; Agar, Jeffrey; Giese, Roger W

2017-07-14

Cooling a 1:1 (v/v) solution of acetonitrile and water at -16° C is known to result in two clear phases. We will refer to this event as "cold-induced aqueous acetonitrile phase separation (CIPS)". On a molar basis, acetonitrile is 71.7% and 13.6% in the upper and lower phases, respectively, in our study. The phase separation proceeds as a descending cloud of microdroplets. At the convenient temperature (typical freezer) employed here the lower phase is rather resistant to solidification, although it emerges from the freezer as a solid if various insoluble matter is present at the outset. In a preliminary way, we replaced the initial (salting-out) step of a representative QuEChERS procedure with CIPS, applying this modified procedure ("CIPS-QuEChERS") to a homogenate of salmon (and partly to beef). Three phases resulted, where only the upper, acetonitrile-rich phase is a liquid (that is completely clear). The middle phase comprises ice and precipitated lipids, while the lower phase is the residual matrix of undissolved salmon or meat. Treating the upper phase from salmon, after isolation, with anhydrous MgSO 4 and C18-Si (typical QuEChERS dispersive solid phase extraction sorbents), and injecting into a GC-MS in a nontargeted mode, gives two-fold more preliminary hits for chemicals, and also number of spiked pesticides recovered, relative to that from a comparable QuEChERS method. In part, this is because of much higher background signals in the latter case. Further study of CIPS-QuEChERS is encouraged, including taking advantage of other QuERChERS conditions. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of accelerated solvent extraction and quick, easy, cheap, effective, rugged and safe method for extraction and determination of pharmaceuticals in vegetables.

PubMed

Chuang, Ya-Hui; Zhang, Yingjie; Zhang, Wei; Boyd, Stephen A; Li, Hui

2015-07-24

Land application of biosolids and irrigation with reclaimed water in agricultural production could result in accumulation of pharmaceuticals in vegetable produce. To better assess the potential human health impact from long-term consumption of pharmaceutical-contaminated vegetables, it is important to accurately quantify the amount of pharmaceuticals accumulated in vegetables. In this study, a quick, easy, cheap, effective, rugged and safe (QuEChERS) method was developed and optimized to extract multiple classes of pharmaceuticals from vegetables, which were subsequently quantified by liquid chromatography coupled to tandem mass spectrometry. For the eleven target pharmaceuticals in celery and lettuce, the extraction recovery of the QuEChERS method ranged from 70.1 to 118.6% with relative standard deviation <20%, and the method detection limit was achieved at the levels of nanograms of pharmaceuticals per gram of vegetables. The results revealed that the performance of the QuEChERS method was comparable to, or better than that of accelerated solvent extraction (ASE) method for extraction of pharmaceuticals from plants. The two optimized extraction methods were applied to quantify the uptake of pharmaceuticals by celery and lettuce growing hydroponically. The results showed that all the eleven target pharmaceuticals could be absorbed by the vegetables from water. Compared to the ASE method, the QuEChERS method offers the advantages of short time and reduced costs of sample preparation, and less amount of organic solvents used. The established QuEChERS method could be used to determine the accumulation of multiple classes of pharmaceutical residues in vegetables and other plants, which is needed to evaluate the quality and safety of agricultural produce consumed by humans. Copyright © 2015 Elsevier B.V. All rights reserved.

Simulation of the Plasma Density Evolution during Electron Cyclotron Resonance Heating at the T-10 Tokamak

NASA Astrophysics Data System (ADS)

Dnestrovskij, Yu. N.; Vershkov, V. A.; Danilov, A. V.; Dnestrovskij, A. Yu.; Zenin, V. N.; Lysenko, S. E.; Melnikov, A. V.; Shelukhin, D. A.; Subbotin, G. F.; Cherkasov, S. V.

2018-01-01

In ohmically heated (OH) plasma with low recycling, an improved particle confinement (IPC) mode is established during gas puffing. However, after gas puffing is switched off, this mode is retained only for about 100 ms, after which an abrupt phase transition into the low particle confinement (LPC) mode occurs in the entire plasma cross section. During such a transition, energy transport due to heat conduction does not change. The phase transition in OH plasma is similar to the effect of density pump-out from the plasma core, which occurs after electron cyclotron heating (ECH) is switched on. Analysis of the measured plasma pressure profiles in the T-10 tokamak shows that, after gas puffing in the OH mode is switched off, the plasma pressure profile in the IPC stage becomes more peaked and, after the peakedness exceeds a certain critical value, the IPC-LPC transition occurs. Similar processes are also observed during ECH. If the pressure profile is insufficiently peaked during ECH, then the density pump-out effect comes into play only after the critical peakedness of the pressure profile is reached. In the plasma core, the density and pressure profiles are close to the corresponding canonical profiles. This allows one to derive an expression for the particle flux within the canonical profile model and formulate a criterion for the IPC-LPC transition. The time evolution of the plasma density profile during phase transitions was simulated for a number of T-10 shots with ECH and high recycling. The particle transport coefficients in the IPC and LPC phases, as well as the dependences of these coefficients on the ECH power, are determined.

A sensitive and efficient method for routine pesticide multiresidue analysis in bee pollen samples using gas and liquid chromatography coupled to tandem mass spectrometry.

PubMed

Vázquez, P Parrilla; Lozano, A; Uclés, S; Ramos, M M Gómez; Fernández-Alba, A R

2015-12-24

Several clean-up methods were evaluated for 253 pesticides in pollen samples concentrating on efficient clean-up and the highest number of pesticides satisfying the recovery and precision criteria. These were: (a) modified QuEChERS using dSPE with PSA+C18; (b) freeze-out prior to QuEChERS using dSPE with PSA+C18; (c) freeze-out prior to QuEChERS using dSPE with PSA+C18+Z-Sep; and (d) freeze-out followed by QuEChERS using dSPE with PSA+C18 and SPE with Z-Sep. Determinations were made using LC-MS/MS and GC-MS/MS. The modified QuEChERS protocol applying a freeze-out followed by dSPE with PSA+C18 and SPE clean-up with Z-Sep was selected because it provided the highest number of pesticides with mean recoveries in the 70-120% range, as well as relative standard deviations (RSDs) typically below 20% (12.2% on average) and ensured much better removal of co-extracted matrix compounds of paramount importance in routine analysis. Limits of quantification at levels as low as 5μgkg(-1) were obtained for the majority of the pesticides. The proposed methodology was applied to the analysis of 41 pollen bee samples from different areas in Spain. Pesticides considered potentially toxic to bees (DL50<2μg/bee) were detected in some samples with concentrations up to 72.7μgkg(-1), which could negatively affect honeybee health. Copyright © 2015 Elsevier B.V. All rights reserved.

Characterising Super Earths With The EChO Spacemission Concept

NASA Astrophysics Data System (ADS)

Tessenyi, Marcell; Ollivier, M.; Tinetti, G.; Beaulieu, J. P.; Coudé du Foresto, V.; Encrenaz, T.; Micela, G.; Swinyard, B.; Ribas, I.; Aylward, A.; Tennyson, J.; Swain, M. R.; Sozzetti, A.; Vasisht, G.; Deroo, P.

2011-09-01

Transiting Super Earths orbiting M dwarfs are excellent targets for the prospect of studying potentially habitable extrasolar planets. While most of the currently known Exoplanets are of the Hot Jupiter and Neptune type, attention is now turning to these Super Earths. Two recent examples are GJ 1214b, found by Charbonneau et al. in 2009, and Cancri 55 e, found by Winn et al. in 2011. These candidates offer the opportunity of obtaining spectral signatures of their atmospheres in transiting scenarios, via data obtained by ground based and space observatories, compared to simulated climate scenarios. With the recent selection of the Exoplanet Characterisation Observatory (EChO) mission by ESA for further studies, I present observational strategies and time requirements for a range of targets characterisable by EChO, with a view to Super Earths orbiting M dwarfs.

Dual-Polarized Antenna Arrays with CMOS Power Amplifiers for SiP Integration at W-Band

NASA Astrophysics Data System (ADS)

Giese, Malte; Vehring, Sönke; Böck, Georg; Jacob, Arne F.

2017-09-01

This paper presents requirements and front-end solutions for low-cost communication systems with data rates of 100 Gbit/s. Link budget analyses in different mass-market applications are conducted for that purpose. It proposes an implementation of the front-end as an active antenna array with support for beam steering and polarization multiplexing over the full W-band. The critical system components are investigated and presented. This applies to a transformer coupled power amplifier (PA) in 40 nm bulk CMOS. It shows saturated output power of more than 10 dBm and power-added-efficiency of more than 10 % over the full W-band. Furthermore, the performance of microstrip-to-waveguide transitions is shown exemplarily as an important part of the active antenna as it interfaces active circuitry and antenna in a polymer-and-metal process. The transition test design shows less than 0.9 dB insertion loss and more than 12 dB return loss for the differential transition over the full W-band.

Optical control of hard X-ray polarization by electron injection in a laser wakefield accelerator

PubMed Central

Schnell, Michael; Sävert, Alexander; Uschmann, Ingo; Reuter, Maria; Nicolai, Maria; Kämpfer, Tino; Landgraf, Björn; Jäckel, Oliver; Jansen, Oliver; Pukhov, Alexander; Kaluza, Malte Christoph; Spielmann, Christian

2013-01-01

Laser-plasma particle accelerators could provide more compact sources of high-energy radiation than conventional accelerators. Moreover, because they deliver radiation in femtosecond pulses, they could improve the time resolution of X-ray absorption techniques. Here we show that we can measure and control the polarization of ultra-short, broad-band keV photon pulses emitted from a laser-plasma-based betatron source. The electron trajectories and hence the polarization of the emitted X-rays are experimentally controlled by the pulse-front tilt of the driving laser pulses. Particle-in-cell simulations show that an asymmetric plasma wave can be driven by a tilted pulse front and a non-symmetric intensity distribution of the focal spot. Both lead to a notable off-axis electron injection followed by collective electron–betatron oscillations. We expect that our method for an all-optical steering is not only useful for plasma-based X-ray sources but also has significance for future laser-based particle accelerators. PMID:24026068

Experimental and numerical analysis of clamped joints in front motorbike suspensions

NASA Astrophysics Data System (ADS)

Croccolo, D.; de Agostinis, M.; Vincenzi, N.

2010-06-01

Clamped joints are shaft-hub connections used, as an instance, in front motorbike suspensions to lock the steering plates with the legs and the legs with the wheel pin, by means of one or two bolts. The preloading force, produced during the tightening process, should be evaluated accurately, since it must lock safely the shaft, without overcoming the yielding point of the hub. Firstly, friction coefficients have been evaluated on “ad-hoc designed” specimens, by applying the Design of Experiment approach: the applied tightening torque has been precisely related to the imposed preloading force. Then, the tensile state of clamps have been evaluated both via FEM and by leveraging some design formulae proposed by the Authors as function of the preloading force and of the clamp geometry. Finally, the results have been compared to those given by some strain gauges applied on the tested clamps: the discrepancies between numerical analyses, the design formulae and the experimental results remains under a threshold of 10%.

A Different Kind of Leader for a Different Kind of School? A Study of Two Early College High Schools in North Carolina

ERIC Educational Resources Information Center

Wynn, William H., III

2016-01-01

Early College High Schools (ECHS) allow students to combine high school and college curriculum and graduate with a high school diploma and transferable college credit, with students in many cases earning associate's degrees. ECHS schools have a tendency to focus on students that have been underserved in the education system. Currently there is a…

Use of ammonium formate in QuEChERS for high-throughput analysis of pesticides in food by fast, low-pressure gas chromatography and liquid chromatography tandem mass spectrometry

USDA-ARS?s Scientific Manuscript database

The “quick, easy, cheap, effective, rugged, and safe” (QuEChERS) approach to sample preparation is widely applied in pesticide residue analysis, but the use of magnesium sulfate for salting out in the method is not ideal for mass spectrometry. In this study we developed and evaluated three new diffe...

Differences in clinical characteristics and frequency of accompanying migraine features in episodic and chronic cluster headache.

PubMed

Gaul, C; Christmann, N; Schröder, D; Weber, R; Shanib, H; Diener, H C; Holle, D

2012-05-01

Data on clinical differences between episodic (eCH) and chronic cluster headache (cCH) and accompanying migraine features are limited. History and clinical features of 209 consecutive cluster headache patients (144 eCH, 65 cCH; male:female ratio 3.4 : 1) were obtained in a tertiary headache centre by face-to-face interviews. Relationship between occurrence of accompanying symptoms, pain intensity, comorbid migraine, and circannual and circadian rhythmicity was analysed. 99.5% of patients reported a minimum of one ipsilateral cranial autonomic symptom (CAS); 80% showed at least three CAS. A seasonal rhythmicity was observed in both eCH and cCH. A comorbid headache disorder occurred in 25%. No significant difference was detected between patients with comorbid migraine and without regarding occurrence of phonophobia, photophobia or nausea during cluster attacks. Patients with comorbid migraine reported allodynia significantly (p = 0.022) more often during cluster attacks than patients without comorbid migraine. Occurrence of CAS and attack frequency, as well as periodic patterns of attacks, are relatively uniform in eCH and cCH. Multiple CAS are not related to pain intensity. Allodynia during cluster attacks is a frequent symptom. The unexpectedly high rate of accompanying migrainous features during cluster attacks cannot be explained by comorbid migraine.

Simultaneous analysis of 70 pesticides using HPlc/MS/MS: a comparison of the multiresidue method of Klein and Alder and the QuEChERS method.

PubMed

Riedel, Melanie; Speer, Karl; Stuke, Sven; Schmeer, Karl

2010-01-01

Since 2003, two new multipesticide residue methods for screening crops for a large number of pesticides, developed by Klein and Alder and Anastassiades et al. (Quick, Easy, Cheap, Effective, Rugged, and Safe; QuEChERS), have been published. Our intention was to compare these two important methods on the basis of their extraction efficiency, reproducibility, ruggedness, ease of use, and speed. In total, 70 pesticides belonging to numerous different substance classes were analyzed at two concentration levels by applying both methods, using five different representative matrixes. In the case of the QuEChERS method, the results of the three sample preparation steps (crude extract, extract after SPE, and extract after SPE and acidification) were compared with each other and with the results obtained with the Klein and Alder method. The extraction efficiencies of the QuEChERS method were far higher, and the sample preparation was much quicker when the last two steps were omitted. In most cases, the extraction efficiencies after the first step were approximately 100%. With extraction efficiencies of mostly less than 70%, the Klein and Alder method did not compare favorably. Some analytes caused problems during evaluation, mostly due to matrix influences.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seo, Dongcheol; Peterson, B. J.; Lee, Seung Hun

The resistive bolometers have been successfully installed in the midplane of L-port in Korea Superconducting Tokamak Advanced Research (KSTAR) device. The spatial and temporal resolutions, 4.5 cm and {approx}1 kHz, respectively, enable us to measure the radial profile of the total radiated power from magnetically confined plasma at a high temperature through radiation and neutral particles. The radiated power was measured at all shots. Even at low plasma current, the bolometer signal was detectable. The electron cyclotron resonance heating (ECH) has been used in tokamak for ECH assisted start-up and plasma control by local heating and current drive. The detectorsmore » of resistive bolometer, near the antenna of ECH, are affected by electron cyclotron wave. The tomographic reconstruction, using the Phillips-Tikhonov regularization method, will be carried out for a major radial profile of the radiation emissivity of the circular cross-section plasma.« less

Comparison of QuEChERS sample preparation methods for the analysis of pesticide residues in canned and fresh peach.

PubMed

Costa, Fabiane Pinho; Caldas, Sergiane Souza; Primel, Ednei Gilberto

2014-12-15

Original, citrate and acetate QuEChERS methods were studied in order to evaluate the extraction efficiency and the matrix effect in the extraction of pesticides from canned peach samples. Determinations were performed by gas chromatography coupled to mass spectrometry (GC-MS). The proposed method with extraction using the original QuEChERS method and determination by GC-MS was validated. LOQs ranged between 1 and 10 μg kg(-1) and all analytical curves showed r values higher than 0.99. Recovery values varied from 69% to 125% with RSDs less than 20%. The matrix effect was evaluated and most compounds showed signal enrichment. Robustness was demonstrated using fresh peaches, which provided recovery values within acceptable limits. The applicability of the method was verified and residues of tebuconazole and dimethoate were found in the samples. Copyright © 2014 Elsevier Ltd. All rights reserved.

Determination of ten pyrethroids in various fruit juices: comparison of dispersive liquid-liquid microextraction sample preparation and QuEChERS method combined with dispersive liquid-liquid microextraction.

PubMed

Zhang, Yaohai; Zhang, Xuelian; Jiao, Bining

2014-09-15

Dispersive liquid-liquid microextraction (DLLME) sample preparation and the quick, easy, cheap, effective, rugged and safe (QuEChERS) method combined with DLLME were developed and compared for the analysis of ten pyrethroids in various fruit juices using gas chromatography-electron capture detection (GC-ECD). QuEChERS-DLLME method has found its widespread applications to all the fruit juices including those samples with more complex matrices (orange, lemon, kiwi and mango) while DLLME was confined to the fruit juices with simpler matrices (apple, pear, grape and peach). The two methods provided acceptable recoveries and repeatability. In addition, the applicabilities of two methods were demonstrated with the real samples and further confirmed by gas chromatography-mass spectrometry (GC-MS). Copyright © 2014. Published by Elsevier Ltd.

High brightness photonic lantern kW-class amplifier

NASA Astrophysics Data System (ADS)

Montoya, Juan; Hwang, Chris; Aleshire, Chris; Reed, Patricia; Martz, Dale; Riley, Mike; Trainor, Michael; Belley, Catherine; Shaw, Scot; Fan, T. Y.; Ripin, Dan

2018-02-01

Pump-limited kW-class operation in a multimode fiber amplifier using adaptive mode control was achieved. A photonic lantern front end was used to inject an arbitrary superposition of modes on the input to a kW-class fiber amplifier to achieve a nearly diffraction-limited output. We report on the adaptive spatial mode control architecture which allows for compensating transverse-mode disturbances at high power. We also describe the advantages of adaptive spatial mode control for optical phased array systems. In particular, we show that the additional degrees of freedom allow for broader steering and improved atmospheric turbulence compensation relative to piston-only optical phased arrays.

Response profiles of enteric methane emissions and lactational performance during habituation to dietary coconut oil in dairy cows.

PubMed

Hollmann, M; Powers, W J; Fogiel, A C; Liesman, J S; Beede, D K

2013-03-01

Dietary coconut oil (CNO) can reduce dry matter intake (DMI), enteric methane (eCH(4)) emissions, and milk fat yield of lactating cows. The goals of this research were to examine responses to different CNO concentrations during the habituation period (34-d) and to evaluate temporal patterns of DMI, eCH(4), and milk fat yield. Treatment diets contained (dry basis): 0.0% (CNO0), 1.3% (CNO1.3), 2.7% (CNO2.7), 3.3% (CNO3.3), or 4.0% CNO (CNO4). In experiment 1, 12 primi- or small secundiparous cows were housed in individual, environmentally controlled rooms and fed CNO0, CNO1.3, CNO2.7, or CNO4. Measurements included DMI, eCH(4), and milk yield and composition. Due to a precipitous drop in DMI (26%), cows fed CNO4 were replaced with cows fed CNO3.3 following d 10. Dietary CNO of 2.7% or more reduced eCH(4) emissions. Reduction was greater with increased CNO and during the first than the second half of the day. Simultaneously, decline in DMI of cows fed CNO2.7, CNO3.3, or CNO4 was increasingly precipitous with increased CNO concentration. Total-tract neutral detergent fiber (NDF) digestibility during wk 5 was reduced in cows fed CNO2.7 or CNO3.3, which in part explained concomitantly reduced eCH(4)/DMI. In addition, milk fat yield was depressed at an increasing rate in cows fed CNO2.7, CNO3.3, and CNO4. In experiment 2, DMI was measured individually in 12 multiparous cows during habituation to CNO0, CNO1.3, CNO2.7, or CNO3.3 for 21 d before relocation to individual, environmentally controlled rooms. Dietary CNO2.7 or CNO3.3 reduced DMI by d 4 and total-tract NDF digestibility during wk 5. Relocation to individual rooms was associated with a 15% reduction in DMI, which was not affected by treatment. Results showed that 2.7% or more dietary CNO reduced eCH(4) and DMI, caused milk fat depression, and decreased NDF digestibility. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Full drive-by-wire dynamic control for four-wheel-steer all-wheel-drive vehicles

NASA Astrophysics Data System (ADS)

Fahimi, Farbod

2013-03-01

Most of the controllers introduced for four-wheel-steer (4WS) vehicles are derived with the assumption that the longitudinal speed of the vehicle is constant. However, in real applications, the longitudinal speed varies, and the longitudinal, lateral, and yaw dynamics are coupled. In this paper, the longitudinal dynamics of the vehicle as well as its lateral and yaw motions are controlled simultaneously. This way, the effect of driving/braking forces of the tires on the lateral and yaw motions of the vehicle are automatically included in the control laws. To address the dynamic parameter uncertainty of the vehicle, a chatter-free variable structure controller is introduced. Elimination of chatter is achieved by introducing a dynamically adaptive boundary layer thickness. It is shown via simulations that the proposed control approach performs more robustly than the controllers developed based on dynamic models, in which longitudinal speed is assumed to be constant, and only lateral speed and yaw rate are used as system states. Furthermore, this approach supports all-wheel-drive vehicles. Front-wheel-drive or rear-wheel-drive vehicles are also supported as special cases of an all-wheel-drive vehicle.

Prototype Development of the GMT Fast Steering Mirror

NASA Astrophysics Data System (ADS)

Kim, Young-Soo; Koh, J.; Jung, H.; Jung, H.; Cho, M. K.; Park, W.; Yang, H.; Kim, H.; Lee, K.; Ahn, H.; Park, B.

2013-06-01

A Fast Steering Mirror (FSM) is going to be produced as a secondary mirror of the Giant Magellan Telescope (GMT). FSM is 3.2 m in diameter and the focal ratio is 0.65. It is composed of seven circular segments which match with the primary mirror segments. Each segment contains a light-weighted mirror whose diameter is 1.1 m. It also contains tip-tilt actuators which would compensate wind effect and structure jitter. An FSM prototype (FSMP) has been developed, which consists of a full-size off-axis mirror segment and a tip-tilt test-bed. The main purpose of the FSMP development is to achieve key technologies, such as fabrication of highly aspheric off-axis mirror and tip-tilt actuation. The development has been conducted by a consortium of five institutions in Korea and USA, and led by Korea Astronomy and Space Science Institute. The mirror was light-weighted and grinding of the front surface was finished. Polishing is in progress with computer generated hologram tests. The tip-tilt test-bed has been manufactured and assembled. Frequency tests are being performed and optical tilt set-up is arranged for visual demonstration. In this paper, we present progress of the prototype development, and future works.

Study of a high-resolution, 3D positioning cadmium zinc telluride detector for PET.

PubMed

Gu, Y; Matteson, J L; Skelton, R T; Deal, A C; Stephan, E A; Duttweiler, F; Gasaway, T M; Levin, C S

2011-03-21

This paper investigates the performance of 1 mm resolution cadmium zinc telluride (CZT) detectors for positron emission tomography (PET) capable of positioning the 3D coordinates of individual 511 keV photon interactions. The detectors comprise 40 mm × 40 mm × 5 mm monolithic CZT crystals that employ a novel cross-strip readout with interspersed steering electrodes to obtain high spatial and energy resolution. The study found a single anode FWHM energy resolution of 3.06 ± 0.39% at 511 keV throughout most of the detector volume. Improved resolution is expected with properly shielded front-end electronics. Measurements made using a collimated beam established the efficacy of the steering electrodes in facilitating enhanced charge collection across anodes, as well as a spatial resolution of 0.44 ± 0.07 mm in the direction orthogonal to the electrode planes. Finally, measurements based on coincidence electronic collimation yielded a point spread function with 0.78 ± 0.10 mm FWHM, demonstrating 1 mm spatial resolution capability transverse to the anodes-as expected from the 1 mm anode pitch. These findings indicate that the CZT-based detector concept has excellent performance and shows great promise for a high-resolution PET system.

Protecting Against Damage from Refraction of High Power Microwaves in the DIII-D Tokamak

NASA Astrophysics Data System (ADS)

Lohr, John; Brambila, Rigo; Cengher, Mirela; Chen, Xi; Gorelov, Yuri; Grosnickle, William; Moeller, Charles; Ponce, Dan; Prater, Ron; Torrezan, Antonio; Austin, Max; Doyle, Edward; Hu, Xing; Dormier, Calvin

2017-07-01

Several new protective systems are being installed on the DIII D tokamak to increase the safety margins for plasma operations with injected ECH power at densities approaching cutoff. Inadvertent overdense operation has previously resulted in reflection of an rf beam back into a launcher causing extensive arcing and melt damage on one waveguide line. Damage to microwave diagnostics, which are located on the same side of the tokamak as the ECH launchers, also has occurred. Developing a reliable microwave based interlock to protect the many vulnerable systems in DIII-D has proved to be difficult. Therefore, multiple protective steps have been taken to reduce the risk of damage in the future. Among these is a density interlock generated by the plasma control system, with setpoint determined by the ECH operators based on rf beam trajectories and plasma parameters. Also installed are enhanced video monitoring of the launchers, and an ambient light monitor on each of the waveguide systems, along with a Langmuir probe at the mouth of each launcher. Versatile rf monitors, measuring forward and reflected power in addition to the mode content of the rf beams, have been installed as the last miter bends in each waveguide line. As these systems are characterized, they are being incorporated in the interlock chains, which enable the ECH injection permits. The diagnostics most susceptible to damage from the ECH waves have also been fitted with a variety of protective devices including stripline filters, thin resonant notch filters tuned to the 110 GHz injected microwave frequency, blazed grating filters and shutters. Calculations of rf beam trajectories in the plasmas are performed using the TORAY ray tracing code with input from kinetic profile diagnostics. Using these calculations, strike points for refracted beams on the vacuum vessel are calculated, which allows evaluation of the risk of damage to sensitive diagnostics and hardware.

Pesticide residues in fruit samples: comparison of different QuEChERS methods using liquid chromatography-tandem mass spectrometry.

PubMed

Christia, C; Bizani, E; Christophoridis, C; Fytianos, K

2015-09-01

Acetate- and citrate-buffered quick, easy, cheap, effective, rugged, safe (QuEChERS) pretreatment methods were evaluated for the determination of various pesticides in peaches, grapes, apples, bananas, pears, and strawberries from various regions of Greece, using LC-MS/MS. The purposes of this study were (i) to evaluate which type of QuEChERS method was the most appropriate and effective for each matrix; (ii) to apply the selected QuEChERS method for each matrix, in order to detect and quantify pesticide residues in various fruit samples using UPLC-MS/MS; (iii) to examine the concentration distribution of pesticide classes among fruit originating from various areas; and (iv) to assess pesticide concentration distribution between peel and flesh of fruit in order to evaluate the penetration of pesticide residues in the fruit flesh. Acetate-buffered QuEChERS was found to be the most suitable technique for most of the fruit matrices. According to the recovery values at two different concentration levels, peaches should preferably be treated by the citrate-buffered type, whereas grapes, bananas, apples, pears, and strawberries are best treated by the acetate-buffered version, although the differences in efficiency were small. The addition of graphitized carbon black significantly decreases the recovery of specific pesticides in all matrices except for strawberries. The majority of values do not exceed the official maximum residue levels set by the European Commission. Organophosphates proved to be the most commonly detected category along with triazines-triazoles-conazoles group and by carbamates. Apples and pears seem to be the most contaminated fruit matrices among those tested. Distribution of pesticide classes shows variations between different regions, suggesting different pesticide application practices. In the case of peaches and pears, there is an equal distribution of detected pesticides between peel and flesh, indicating penetration of contaminants into the fruit flesh.

Protecting against damage from refraction of high power microwaves in the DIII-D tokamak

DOE PAGES

Lohr, John; Brambila, Rigo; Cengher, Mirela; ...

2017-07-24

Here, several new protective systems are being installed on the DIII D tokamak to increase the safety margins for plasma operations with injected ECH power at densities approaching cutoff. Inadvertent overdense operation has previously resulted in reflection of an rf beam back into a launcher causing extensive arcing and melt damage on one waveguide line. Damage to microwave diagnostics, which are located on the same side of the tokamak as the ECH launchers, also has occurred. Developing a reliable microwave based interlock to protect the many vulnerable systems in DIII-D has proved to be difficult. Therefore, multiple protective steps havemore » been taken to reduce the risk of damage in the future. Among these is a density interlock generated by the plasma control system, with setpoint determined by the ECH operators based on rf beam trajectories and plasma parameters. Also installed are enhanced video monitoring of the launchers, and an ambient light monitor on each of the waveguide systems, along with a Langmuir probe at the mouth of each launcher. Versatile rf monitors, measuring forward and reflected power in addition to the mode content of the rf beams, have been installed as the last miter bends in each waveguide line. As these systems are characterized, they are being incorporated in the interlock chains, which enable the ECH injection permits. The diagnostics most susceptible to damage from the ECH waves have also been fitted with a variety of protective devices including stripline filters, thin resonant notch filters tuned to the 110 GHz injected microwave frequency, blazed grating filters and shutters. Calculations of rf beam trajectories in the plasmas are performed using the TORAY ray tracing code with input from kinetic profile diagnostics. Using these calculations, strike points for refracted beams on the vacuum vessel are calculated, which allows evaluation of the risk of damage to sensitive diagnostics and hardware.« less

Protecting against damage from refraction of high power microwaves in the DIII-D tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lohr, John; Brambila, Rigo; Cengher, Mirela

Here, several new protective systems are being installed on the DIII D tokamak to increase the safety margins for plasma operations with injected ECH power at densities approaching cutoff. Inadvertent overdense operation has previously resulted in reflection of an rf beam back into a launcher causing extensive arcing and melt damage on one waveguide line. Damage to microwave diagnostics, which are located on the same side of the tokamak as the ECH launchers, also has occurred. Developing a reliable microwave based interlock to protect the many vulnerable systems in DIII-D has proved to be difficult. Therefore, multiple protective steps havemore » been taken to reduce the risk of damage in the future. Among these is a density interlock generated by the plasma control system, with setpoint determined by the ECH operators based on rf beam trajectories and plasma parameters. Also installed are enhanced video monitoring of the launchers, and an ambient light monitor on each of the waveguide systems, along with a Langmuir probe at the mouth of each launcher. Versatile rf monitors, measuring forward and reflected power in addition to the mode content of the rf beams, have been installed as the last miter bends in each waveguide line. As these systems are characterized, they are being incorporated in the interlock chains, which enable the ECH injection permits. The diagnostics most susceptible to damage from the ECH waves have also been fitted with a variety of protective devices including stripline filters, thin resonant notch filters tuned to the 110 GHz injected microwave frequency, blazed grating filters and shutters. Calculations of rf beam trajectories in the plasmas are performed using the TORAY ray tracing code with input from kinetic profile diagnostics. Using these calculations, strike points for refracted beams on the vacuum vessel are calculated, which allows evaluation of the risk of damage to sensitive diagnostics and hardware.« less

Comparison of two extraction methods for the determination of 135 pesticides in Corydalis Rhizoma, Chuanxiong Rhizoma and Angelicae Sinensis Radix by liquid chromatography-triple quadrupole-mass spectrometry. Application to the roots and rhizomes of Chinese herbal medicines.

PubMed

Liu, Jie; Tong, Ling; Li, Dongxiang; Meng, Wenting; Sun, Wanyang; Zhao, Yunli; Yu, Zhiguo

2016-04-01

In this study, two simple pretreatment methods were comprehensively evaluated for the determination of 135 pesticide residues in roots and rhizomes of Chinese herbal medicines (CHMs). The studied methodologies are (a) solid-phase extraction (SPE) and (b) Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS). For SPE, extraction solvents, SPE cartridges and types and volume of eluent were accessed and optimized. For QuEChERS, different versions, acetic acid concentration and dispersive solid-phase extraction (dSPE) sorbent materials were tested. SPE and QuEChERS were estimated in recovery range, the number of pesticides that were recovered ranging from 90% to 110% and expenses in Corydalis Rhizoma, Chuanxiong Rhizoma and Angelicae Sinensis Radix. QuEChERS method showed better performance than SPE. The method showed good linearity over the range assayed 0.9986-0.9999 (1-80ng/mL for 124 pesticides, 1-50ng/mL for 10 pesticides, 1-20ng/mL for satisfar). The matrix effect was compensated by matrix-based calibration curves with internal standard. The average recoveries of all pesticides were ranging from 70% to 120% at three levels of 10, 50 and 100ng/g with relative standard deviations less than 20%. The limits of quantification of the 135 pesticides in three matrices were 1-5ng/g, which were below the maximum residue levels (MRLs) established by the European Union. The verified QuEChERS method was successfully applied to the analysis of 65 actual samples from eight different types of roots and rhizomes of CHMs. Angelicae Sinensis Radix was the most susceptible to pesticides among these samples, and the most frequently detected pesticide was carbendazim with levels below MRLs. Metalaxyl, phorate, atrazine, diniconazole, coumaphos and paclobutrazol were also detected in some samples. Copyright © 2016 Elsevier B.V. All rights reserved.

Simultaneous determination of multiclass pesticide residues in human plasma using a mini QuEChERS method.

PubMed

Srivastava, Anshuman; Rai, Satyajeet; Kumar Sonker, Ashish; Karsauliya, Kajal; Pandey, Chandra Prabha; Singh, Sheelendra Pratap

2017-06-01

Blood is one of the most assessable matrices for the determination of pesticide residue exposure in humans. Effective sample preparation/cleanup of biological samples is very important in the development of a sensitive, reproducible, and robust method. In the present study, a simple, cost-effective, and rapid gas chromatography-tandem mass spectrometry method has been developed and validated for simultaneous analysis of 31 multiclass (organophosphates, organochlorines, and synthetic pyrethroids) pesticide residues in human plasma by means of a mini QuEChERS (quick, easy, cheap, effective, rugged, and safe) method. We have adopted a modified version of the QuEChERS method, which is primarily used for pesticide residue analysis in food commodities. The QuEChERS method was optimized by use of different extraction solvents and different amounts and combinations of salts and sorbents (primary-secondary amines and C 18 ) for the dispersive solid-phase extraction step. The results show that a combination of ethyl acetate with 2% acetic acid, magnesium sulfate (0.4 g), and solid-phase extraction for sample cleanup with primary-secondary amines (50 mg) per 1-mL volume of plasma is the most suitable for generating acceptable results with high recoveries for all multiclass pesticides from human plasma. The mean recovery ranged from 74% to 109% for all the analytes. The limit of quantification and limit of detection of the method ranged from 0.12 to 13.53 ng mL -1 and from 0.04 to 4.10 ng mL -1 respectively. The intraday precision and the interday precision of the method were 6% or less and 11% or less respectively. This method would be useful for the analysis of a wide range of pesticides of interest in a small volume of clinical and/or forensic samples to support biomonitoring and toxicological applications. Graphical Abstract Pesticide residues analysis in human plasma using mini QuEChERS method.

The EChO science case

NASA Astrophysics Data System (ADS)

Tinetti, Giovanna; Drossart, Pierre; Eccleston, Paul; Hartogh, Paul; Isaak, Kate; Linder, Martin; Lovis, Christophe; Micela, Giusi; Ollivier, Marc; Puig, Ludovic; Ribas, Ignasi; Snellen, Ignas; Swinyard, Bruce; Allard, France; Barstow, Joanna; Cho, James; Coustenis, Athena; Cockell, Charles; Correia, Alexandre; Decin, Leen; de Kok, Remco; Deroo, Pieter; Encrenaz, Therese; Forget, Francois; Glasse, Alistair; Griffith, Caitlin; Guillot, Tristan; Koskinen, Tommi; Lammer, Helmut; Leconte, Jeremy; Maxted, Pierre; Mueller-Wodarg, Ingo; Nelson, Richard; North, Chris; Pallé, Enric; Pagano, Isabella; Piccioni, Guseppe; Pinfield, David; Selsis, Franck; Sozzetti, Alessandro; Stixrude, Lars; Tennyson, Jonathan; Turrini, Diego; Zapatero-Osorio, Mariarosa; Beaulieu, Jean-Philippe; Grodent, Denis; Guedel, Manuel; Luz, David; Nørgaard-Nielsen, Hans Ulrik; Ray, Tom; Rickman, Hans; Selig, Avri; Swain, Mark; Banaszkiewicz, Marek; Barlow, Mike; Bowles, Neil; Branduardi-Raymont, Graziella; du Foresto, Vincent Coudé; Gerard, Jean-Claude; Gizon, Laurent; Hornstrup, Allan; Jarchow, Christopher; Kerschbaum, Franz; Kovacs, Géza; Lagage, Pierre-Olivier; Lim, Tanya; Lopez-Morales, Mercedes; Malaguti, Giuseppe; Pace, Emanuele; Pascale, Enzo; Vandenbussche, Bart; Wright, Gillian; Ramos Zapata, Gonzalo; Adriani, Alberto; Azzollini, Ruymán; Balado, Ana; Bryson, Ian; Burston, Raymond; Colomé, Josep; Crook, Martin; Di Giorgio, Anna; Griffin, Matt; Hoogeveen, Ruud; Ottensamer, Roland; Irshad, Ranah; Middleton, Kevin; Morgante, Gianluca; Pinsard, Frederic; Rataj, Mirek; Reess, Jean-Michel; Savini, Giorgio; Schrader, Jan-Rutger; Stamper, Richard; Winter, Berend; Abe, L.; Abreu, M.; Achilleos, N.; Ade, P.; Adybekian, V.; Affer, L.; Agnor, C.; Agundez, M.; Alard, C.; Alcala, J.; Allende Prieto, C.; Alonso Floriano, F. J.; Altieri, F.; Alvarez Iglesias, C. A.; Amado, P.; Andersen, A.; Aylward, A.; Baffa, C.; Bakos, G.; Ballerini, P.; Banaszkiewicz, M.; Barber, R. J.; Barrado, D.; Barton, E. J.; Batista, V.; Bellucci, G.; Belmonte Avilés, J. A.; Berry, D.; Bézard, B.; Biondi, D.; Błęcka, M.; Boisse, I.; Bonfond, B.; Bordé, P.; Börner, P.; Bouy, H.; Brown, L.; Buchhave, L.; Budaj, J.; Bulgarelli, A.; Burleigh, M.; Cabral, A.; Capria, M. T.; Cassan, A.; Cavarroc, C.; Cecchi-Pestellini, C.; Cerulli, R.; Chadney, J.; Chamberlain, S.; Charnoz, S.; Christian Jessen, N.; Ciaravella, A.; Claret, A.; Claudi, R.; Coates, A.; Cole, R.; Collura, A.; Cordier, D.; Covino, E.; Danielski, C.; Damasso, M.; Deeg, H. J.; Delgado-Mena, E.; Del Vecchio, C.; Demangeon, O.; De Sio, A.; De Wit, J.; Dobrijévic, M.; Doel, P.; Dominic, C.; Dorfi, E.; Eales, S.; Eiroa, C.; Espinoza Contreras, M.; Esposito, M.; Eymet, V.; Fabrizio, N.; Fernández, M.; Femenía Castella, B.; Figueira, P.; Filacchione, G.; Fletcher, L.; Focardi, M.; Fossey, S.; Fouqué, P.; Frith, J.; Galand, M.; Gambicorti, L.; Gaulme, P.; García López, R. J.; Garcia-Piquer, A.; Gear, W.; Gerard, J.-C.; Gesa, L.; Giani, E.; Gianotti, F.; Gillon, M.; Giro, E.; Giuranna, M.; Gomez, H.; Gomez-Leal, I.; Gonzalez Hernandez, J.; González Merino, B.; Graczyk, R.; Grassi, D.; Guardia, J.; Guio, P.; Gustin, J.; Hargrave, P.; Haigh, J.; Hébrard, E.; Heiter, U.; Heredero, R. L.; Herrero, E.; Hersant, F.; Heyrovsky, D.; Hollis, M.; Hubert, B.; Hueso, R.; Israelian, G.; Iro, N.; Irwin, P.; Jacquemoud, S.; Jones, G.; Jones, H.; Justtanont, K.; Kehoe, T.; Kerschbaum, F.; Kerins, E.; Kervella, P.; Kipping, D.; Koskinen, T.; Krupp, N.; Lahav, O.; Laken, B.; Lanza, N.; Lellouch, E.; Leto, G.; Licandro Goldaracena, J.; Lithgow-Bertelloni, C.; Liu, S. J.; Lo Cicero, U.; Lodieu, N.; Lognonné, P.; Lopez-Puertas, M.; Lopez-Valverde, M. A.; Lundgaard Rasmussen, I.; Luntzer, A.; Machado, P.; MacTavish, C.; Maggio, A.; Maillard, J.-P.; Magnes, W.; Maldonado, J.; Mall, U.; Marquette, J.-B.; Mauskopf, P.; Massi, F.; Maurin, A.-S.; Medvedev, A.; Michaut, C.; Miles-Paez, P.; Montalto, M.; Montañés Rodríguez, P.; Monteiro, M.; Montes, D.; Morais, H.; Morales, J. C.; Morales-Calderón, M.; Morello, G.; Moro Martín, A.; Moses, J.; Moya Bedon, A.; Murgas Alcaino, F.; Oliva, E.; Orton, G.; Palla, F.; Pancrazzi, M.; Pantin, E.; Parmentier, V.; Parviainen, H.; Peña Ramírez, K. Y.; Peralta, J.; Perez-Hoyos, S.; Petrov, R.; Pezzuto, S.; Pietrzak, R.; Pilat-Lohinger, E.; Piskunov, N.; Prinja, R.; Prisinzano, L.; Polichtchouk, I.; Poretti, E.; Radioti, A.; Ramos, A. A.; Rank-Lüftinger, T.; Read, P.; Readorn, K.; Rebolo López, R.; Rebordão, J.; Rengel, M.; Rezac, L.; Rocchetto, M.; Rodler, F.; Sánchez Béjar, V. J.; Sanchez Lavega, A.; Sanromá, E.; Santos, N.; Sanz Forcada, J.; Scandariato, G.; Schmider, F.-X.; Scholz, A.; Scuderi, S.; Sethenadh, J.; Shore, S.; Showman, A.; Sicardy, B.; Sitek, P.; Smith, A.; Soret, L.; Sousa, S.; Stiepen, A.; Stolarski, M.; Strazzulla, G.; Tabernero, H. M.; Tanga, P.; Tecsa, M.; Temple, J.; Terenzi, L.; Tessenyi, M.; Testi, L.; Thompson, S.; Thrastarson, H.; Tingley, B. W.; Trifoglio, M.; Martín Torres, J.; Tozzi, A.; Turrini, D.; Varley, R.; Vakili, F.; de Val-Borro, M.; Valdivieso, M. L.; Venot, O.; Villaver, E.; Vinatier, S.; Viti, S.; Waldmann, I.; Waltham, D.; Ward-Thompson, D.; Waters, R.; Watkins, C.; Watson, D.; Wawer, P.; Wawrzaszk, A.; White, G.; Widemann, T.; Winek, W.; Wiśniowski, T.; Yelle, R.; Yung, Y.; Yurchenko, S. N.

2015-12-01

The discovery of almost two thousand exoplanets has revealed an unexpectedly diverse planet population. We see gas giants in few-day orbits, whole multi-planet systems within the orbit of Mercury, and new populations of planets with masses between that of the Earth and Neptune—all unknown in the Solar System. Observations to date have shown that our Solar System is certainly not representative of the general population of planets in our Milky Way. The key science questions that urgently need addressing are therefore: What are exoplanets made of? Why are planets as they are? How do planetary systems work and what causes the exceptional diversity observed as compared to the Solar System? The EChO (Exoplanet Characterisation Observatory) space mission was conceived to take up the challenge to explain this diversity in terms of formation, evolution, internal structure and planet and atmospheric composition. This requires in-depth spectroscopic knowledge of the atmospheres of a large and well-defined planet sample for which precise physical, chemical and dynamical information can be obtained. In order to fulfil this ambitious scientific program, EChO was designed as a dedicated survey mission for transit and eclipse spectroscopy capable of observing a large, diverse and well-defined planet sample within its 4-year mission lifetime. The transit and eclipse spectroscopy method, whereby the signal from the star and planet are differentiated using knowledge of the planetary ephemerides, allows us to measure atmospheric signals from the planet at levels of at least 10-4 relative to the star. This can only be achieved in conjunction with a carefully designed stable payload and satellite platform. It is also necessary to provide broad instantaneous wavelength coverage to detect as many molecular species as possible, to probe the thermal structure of the planetary atmospheres and to correct for the contaminating effects of the stellar photosphere. This requires wavelength coverage of at least 0.55 to 11 μm with a goal of covering from 0.4 to 16 μm. Only modest spectral resolving power is needed, with R ~ 300 for wavelengths less than 5 μm and R ~ 30 for wavelengths greater than this. The transit spectroscopy technique means that no spatial resolution is required. A telescope collecting area of about 1 m2 is sufficiently large to achieve the necessary spectro-photometric precision: for the Phase A study a 1.13 m2 telescope, diffraction limited at 3 μm has been adopted. Placing the satellite at L2 provides a cold and stable thermal environment as well as a large field of regard to allow efficient time-critical observation of targets randomly distributed over the sky. EChO has been conceived to achieve a single goal: exoplanet spectroscopy. The spectral coverage and signal-to-noise to be achieved by EChO, thanks to its high stability and dedicated design, would be a game changer by allowing atmospheric composition to be measured with unparalleled exactness: at least a factor 10 more precise and a factor 10 to 1000 more accurate than current observations. This would enable the detection of molecular abundances three orders of magnitude lower than currently possible and a fourfold increase from the handful of molecules detected to date. Combining these data with estimates of planetary bulk compositions from accurate measurements of their radii and masses would allow degeneracies associated with planetary interior modelling to be broken, giving unique insight into the interior structure and elemental abundances of these alien worlds. EChO would allow scientists to study exoplanets both as a population and as individuals. The mission can target super-Earths, Neptune-like, and Jupiter-like planets, in the very hot to temperate zones (planet temperatures of 300-3000 K) of F to M-type host stars. The EChO core science would be delivered by a three-tier survey. The EChO Chemical Census: This is a broad survey of a few-hundred exoplanets, which allows us to explore the spectroscopic and chemical diversity of the exoplanet population as a whole. The EChO Origin: This is a deep survey of a subsample of tens of exoplanets for which significantly higher signal to noise and spectral resolution spectra can be obtained to explain the origin of the exoplanet diversity (such as formation mechanisms, chemical processes, atmospheric escape). The EChO Rosetta Stones: This is an ultra-high accuracy survey targeting a subsample of select exoplanets. These will be the bright "benchmark" cases for which a large number of measurements would be taken to explore temporal variations, and to obtain two and three dimensional spatial information on the atmospheric conditions through eclipse-mapping techniques. If EChO were launched today, the exoplanets currently observed are sufficient to provide a large and diverse sample. The Chemical Census survey would consist of > 160 exoplanets with a range of planetary sizes, temperatures, orbital parameters and stellar host properties. Additionally, over the next 10 years, several new ground- and space-based transit photometric surveys and missions will come on-line (e.g. NGTS, CHEOPS, TESS, PLATO), which will specifically focus on finding bright, nearby systems. The current rapid rate of discovery would allow the target list to be further optimised in the years prior to EChO's launch and enable the atmospheric characterisation of hundreds of planets.

Tardigrades from Nahuel Huapi National Park (Argentina, South America) with descriptions of two new Macrobiotidae species.

PubMed

Roszkowska, Milena; Stec, Daniel; Ciobanu, Daniel Adrian; Kaczmarek, Łukasz

2016-04-21

In 31 samples of mosses and lichens collected in the Argentinean province of Río Negro, 657 tardigrades, 53 exuviae and 219 free-laid eggs were found. In total, 20 species were identified: Diphascon chilenense, Dip. mitrense, Echiniscus bigranulatus, Ech. corrugicaudatus, Ech. merokensis merokensis, Ech. testudo, Hebesuncus mollispinus, Hypsibius convergens, Macrobiotus cf. anderssoni, Mac. andinus, Mac. kazmierskii, Mac. patagonicus, Mesobiotus szeptyckii, Mes. pseudoblocki sp. nov., Milnesium argentinum, Mil. beatae, Mil. brachyungue, Mil. granulatum, Mopsechiniscus granulosus, Minibiotus pseudostellarus sp. nov. Of the two new species, Mesobiotus pseudoblocki sp. nov. is most similar to Mes. blocki, but it differs mainly by the lack of dentate lunules, smaller eggs and presence of reticular design on egg processes. Minibiotus pseudostellarus sp. nov. is most similar to Min. constellatus, Min. eichhorni, Min. sidereus or Min. vinciguerrae, but it differs from them by the presence of 'pseudo-star'-shaped pores in the dorsal cuticle instead of fully developed 'stars' and by other morphometric characters.

Exoplanet atmospheres with EChO: spectral retrievals using EChOSim

NASA Astrophysics Data System (ADS)

Barstow, Joanna K.; Bowles, Neil E.; Aigrain, Suzanne; Fletcher, Leigh N.; Irwin, Patrick G. J.; Varley, Ryan; Pascale, Enzo

2015-12-01

We demonstrate the effectiveness of the Exoplanet Characterisation Observatory mission concept for constraining the atmospheric properties of hot and warm gas giants and super Earths. Synthetic primary and secondary transit spectra for a range of planets are passed through EChOSim [13] to obtain the expected level of noise for different observational scenarios; these are then used as inputs for the NEMESIS atmospheric retrieval code and the retrieved atmospheric properties (temperature structure, composition and cloud properties) compared with the known input values, following the method of [1]. To correctly retrieve the temperature structure and composition of the atmosphere to within 2 σ, we find that we require: a single transit or eclipse of a hot Jupiter orbiting a sun-like (G2) star at 35 pc to constrain the terminator and dayside atmospheres; 20 transits or eclipses of a warm Jupiter orbiting a similar star; 10 transits/eclipses of a hot Neptune orbiting an M dwarf at 6 pc; and 30 transits or eclipses of a GJ1214b-like planet.

QuEChERS Purification Combined with Ultrahigh-Performance Liquid Chromatography Tandem Mass Spectrometry for Simultaneous Quantification of 25 Mycotoxins in Cereals.

PubMed

Sun, Juan; Li, Weixi; Zhang, Yan; Hu, Xuexu; Wu, Li; Wang, Bujun

2016-12-15

A method based on the QuEChERS (quick, easy, cheap, effective, rugged, and safe) purification combined with ultrahigh performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS), was optimized for the simultaneous quantification of 25 mycotoxins in cereals. Samples were extracted with a solution containing 80% acetonitrile and 0.1% formic acid, and purified with QuEChERS before being separated by a C18 column. The mass spectrometry was conducted by using positive electrospray ionization (ESI+) and multiple reaction monitoring (MRM) models. The method gave good linear relations with regression coefficients ranging from 0.9950 to 0.9999. The detection limits ranged from 0.03 to 15.0 µg·kg -1 , and the average recovery at three different concentrations ranged from 60.2% to 115.8%, with relative standard deviations (RSD%) varying from 0.7% to 19.6% for the 25 mycotoxins. The method is simple, rapid, accurate, and an improvement compared with the existing methods published so far.

Response of a core coherent density oscillation on electron cyclotron resonance heating in Heliotron J plasma

NASA Astrophysics Data System (ADS)

Kobayashi, T.; Kobayashi, S.; Lu, X. X.; Kenmochi, N.; Ida, K.; Ohshima, S.; Yamamoto, S.; Kado, S.; Kokubu, D.; Nagasaki, K.; Okada, H.; Minami, T.; Otani, Y.; Mizuuchi, T.

2018-01-01

We report properties of a coherent density oscillation observed in the core region and its response to electron cyclotron resonance heating (ECH) in Heliotron J plasma. The measurement was performed using a multi-channel beam emission spectroscopy system. The density oscillation is observed in a radial region between the core and the half radius. The poloidal mode number is found to be 1 (or 2). By modulating the ECH power with 100 Hz, repetition of formation and deformation of a strong electron temperature gradient, which is likely ascribed to be an electron internal transport barrier, is realized. Amplitude and rotation frequency of the coherent density oscillation sitting at the strong electron temperature gradient location are modulated by the ECH, while the poloidal mode structure remains almost unchanged. The change in the rotation velocity in the laboratory frame is derived. Assuming that the change of the rotation velocity is given by the background E × B velocity, a possible time evolution of the radial electric field was deduced.

Detecting a wide range of environmental contaminants in human blood samples--combining QuEChERS with LC-MS and GC-MS methods.

PubMed

Plassmann, Merle M; Schmidt, Magdalena; Brack, Werner; Krauss, Martin

2015-09-01

Exposure to environmental pollution and consumer products may result in an uptake of chemicals into human tissues. Several studies have reported the presence of diverse environmental contaminants in human blood samples. However, previously developed multi-target methods for the analysis of human blood include a fairly limited amount of compounds stemming from one or two related compound groups. Thus, the sample preparation method QuEChERS (quick easy cheap effective rugged and safe) was tested for the extraction of 64 analytes covering a broad compound domain followed by detection using liquid and gas chromatography coupled to mass spectrometry (LC- and GC-MS). Forty-seven analytes showed absolute recoveries above 70% in the first QuEChERS step, being a simple liquid-liquid extraction (LLE) using acetonitrile and salt. The second QuEChERS step, being a dispersive solid phase extraction, did not result in an overall improvement of recoveries or removal of background signals. Using solely the LLE step, eight analytes could subsequently be detected in human blood samples from the German Environmental Specimen Bank. Using a LC-multiple reaction monitoring (MRM) method with a triple quadrupole instrument, better recoveries were achieved than with an older LC-high-resolution (HR) MS full scan orbitrap instrument, which required a higher concentration factor of the extracts. However, the application of HRMS full scan methods could be used for the detection of additional compounds retrospectively.

The effects of inhalation anaesthetics on common clinical pathology parameters in laboratory rats.

PubMed

Deckardt, K; Weber, I; Kaspers, U; Hellwig, J; Tennekes, H; van Ravenzwaay, B

2007-09-01

Effects of common anaesthetics such as ether, methoxyflurane, isoflurane, carbon dioxide (at 100%, 80% or 60% admixed with O(2)) on toxicity and clinical pathology parameters in rats were investigated. Ether, methoxyflurane and 100% CO(2) induced toxicity in some animals. Erythrocyte, haemoglobin and haematocrit were reduced in females by 100% CO(2), methoxyflurane and isoflurane. Glucose was increased by 60% CO(2), 80% CO(2), ether, isoflurane and methoxyflurane in males. Chloride was reduced by isoflurane and all CO(2) concentrations in females. Serum proteins were reduced by isoflurane and methoxyflurane. Sodium, inorganic phosphate, calcium and magnesium were reduced by methoxyflurane and isoflurane, but increased by all CO(2) concentrations. Potassium was reduced by ether, methoxyflurane or isoflurane. Triiodothyronine and thyroxine were reduced by all anaesthetics. Prolactin was reduced by methoxyflurane, but raised by ether and isoflurane. Erythrocyte cholinesterase (E-ChE) activity is markedly reduced (20-40%) after anaesthesia with all CO(2) concentrations in both sexes. E-ChE was unaffected by ether, methoxyflurane, or isoflurane. Serum and brain cholinesterase activities were not affected. E-ChE inhibition correlated with decreased blood pH, suggesting that this was caused by acidosis. This is of practical relevance in the risk assessment of cholinesterase inhibitors. Clinical pathology data were affected by all anaesthetics. CO(2)/O(2) (80%/20%) and isoflurane are the most suitable anaesthetics. If E-ChE activity is to be determined, isoflurane is the anaesthetic of choice.

Metallomics of two microorganisms relevant to heavy metal bioremediation reveal fundamental differences in metal assimilation and utilization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lancaster, Andrew; Menon, Angeli; Scott, Israel

2014-03-26

Although as many as half of all proteins are thought to require a metal cofactor, the metalloproteomes of microorganisms remain relatively unexplored. Microorganisms from different environments are likely to vary greatly in the metals that they assimilate, not just among the metals with well-characterized roles but also those lacking any known function. Herein we investigated the metal utilization of two microorganisms that were isolated from very similar environments and are of interest because of potential roles in the immobilization of heavy metals, such as uranium and chromium. The metals assimilated and their concentrations in the cytoplasm of Desulfovibrio vulgaris strainmore » Hildenborough (DvH) and Enterobacter cloacae strain Hanford (EcH) varied dramatically, with a larger number of metals present in Enterobacter. For example, a total of 9 and 19 metals were assimilated into their cytoplasmic fractions, respectively, and DvH did not assimilate significant amounts of zinc or copper whereas EcH assimilated both. However, bioinformatic analysis of their genome sequences revealed a comparable number of predicted metalloproteins, 813 in DvH and 953 in EcH. These allowed some rationalization of the types of metal assimilated in some cases (Fe, Cu, Mo, W, V) but not in others (Zn, Nd, Ce, Pr, Dy, Hf and Th). It was also shown that U binds an unknown soluble protein in EcH but this incorporation was the result of extracellular U binding to cytoplasmic components after cell lysis.« less

Accelerated solvent extraction by using an 'in-line' clean-up approach for multiresidue analysis of pesticides in organic honey.

PubMed

Chiesa, Luca Maria; Labella, Giuseppe Federico; Panseri, Sara; Britti, Domenico; Galbiati, Fabrizio; Villa, Roberto; Arioli, Francesco

2017-05-01

The worldwide loss of honeybee colonies may be due to their exposure to several contaminants (i.e., pesticides); such contamination may also have impacts on consumers' health. Therefore, it is essential to develop quick and new methods to detect several pesticide residues in honey samples. In this study, the effectiveness of accelerated solvent extraction (ASE) was compared with QuEChERS methods for the analysis of 53 pesticides in organic honey by gas chromatography-triple quadrupole mass spectrometry. Two simple and rapid ASE methods with 'in-line' clean-up were optimised and then compared with QuEChERS. Hexane-ethyl acetate (Hex:EtAc) and Florisil were chosen as extraction solvent and retainer for the first ASE method respectively; acetonitrile and a primary-secondary amine phase (ACN-PSA) were selected for the second ASE method. The methods were validated according to the European Union SANTE/11945/2015 guidelines. The validation parameters showed that QuEChERS and ASE with PSA as retainer had better repeatability than ASE with Hex:EtAc and Florisil. In particular, QuEChERS and ASE (ACN-PSA) showed good recovery, according to the SANTE criteria, for the majority of investigated pesticides. Conversely, when ASE with Hex:EtAc and Florisil was used as the retainer, several compounds showed recoveries lower than the acceptable value of 70%. The ASE in-line method was finally applied to evaluate pesticide concentration in organic honey samples.

Fuzzy Logic Based Autonomous Parallel Parking System with Kalman Filtering

NASA Astrophysics Data System (ADS)

Panomruttanarug, Benjamas; Higuchi, Kohji

This paper presents an emulation of fuzzy logic control schemes for an autonomous parallel parking system in a backward maneuver. There are four infrared sensors sending the distance data to a microcontroller for generating an obstacle-free parking path. Two of them mounted on the front and rear wheels on the parking side are used as the inputs to the fuzzy rules to calculate a proper steering angle while backing. The other two attached to the front and rear ends serve for avoiding collision with other cars along the parking space. At the end of parking processes, the vehicle will be in line with other parked cars and positioned in the middle of the free space. Fuzzy rules are designed based upon a wall following process. Performance of the infrared sensors is improved using Kalman filtering. The design method needs extra information from ultrasonic sensors. Starting from modeling the ultrasonic sensor in 1-D state space forms, one makes use of the infrared sensor as a measurement to update the predicted values. Experimental results demonstrate the effectiveness of sensor improvement.

The wave-field from an array of periodic emitters driven simultaneously by a broadband pulse.

PubMed

Dixon, Steve; Hill, Samuel; Fan, Yichao; Rowlands, George

2013-06-01

The use of phased array methods are commonplace in ultrasonic applications, where controlling the variation of the phase between the narrowband emitters in an array facilitates beam steering and focusing of ultrasonic waves. An approach is presented here whereby emitters of alternating polarity arranged in a one-dimensional array are pulsed simultaneously, and have sufficiently wide, controlled bandwidth to emit a two-dimensional wave. This pulsed approach provides a rapid means of simultaneously covering a region of space with a wave-front, whereby any wave that scatters or reflects off a body to a detector will have a distinct arrival time and frequency. This is a general wave phenomenon with a potential application in radar, sonar, and ultrasound. The key result is that one can obtain a smooth, continuous wave-front emitted from the array, over a large solid angle, whose frequency varies as a function of angle to the array. Analytic and finite element models created to describe this phenomenon have been validated with experimental results using ultrasonic waves in metal samples.

Experimental Semiautonomous Vehicle

NASA Technical Reports Server (NTRS)

Wilcox, Brian H.; Mishkin, Andrew H.; Litwin, Todd E.; Matthies, Larry H.; Cooper, Brian K.; Nguyen, Tam T.; Gat, Erann; Gennery, Donald B.; Firby, Robert J.; Miller, David P.;

Banded Structures in Electron Pitch Angle Diffusion Coefficients from Resonant Wave Particle Interactions

NASA Technical Reports Server (NTRS)

Tripathi, A. K.; Singhal, R. P.; Khazanov, G. V.; Avanov, L. A.

2016-01-01

Electron pitch angle (D (alpha)) and momentum (D(pp)) diffusion coefficients have been calculated due to resonant interactions with electrostatic electron cyclotron harmonic (ECH) and whistler mode chorus waves. Calculations have been performed at two spatial locations L = 4.6 and 6.8 for electron energies 10 keV. Landau (n = 0) resonance and cyclotron harmonic resonances n = +/-1, +/-2,...+/-5 have been included in the calculations. It is found that diffusion coefficient versus pitch angle (alpha) profiles show large dips and oscillations or banded structures. The structures are more pronounced for ECH and lower band chorus (LBC) and particularly at location 4.6. Calculations of diffusion coefficients have also been performed for individual resonances. It is noticed that the main contribution of ECH waves in pitch angle diffusion coefficient is due to resonances n = +1 and n = +2. A major contribution to momentum diffusion coefficients appears from n = +2. However, the banded structures in D alpha and Dpp coefficients appear only in the profile of diffusion coefficients for n = +2. The contribution of other resonances to diffusion coefficients is found to be, in general, quite small or even negligible. For LBC and upper band chorus waves, the banded structures appear only in Landau resonance. The Dpp diffusion coefficient for ECH waves is one to two orders smaller than D alpha coefficients. For chorus waves, Dpp coefficients are about an order of magnitude smaller than D alpha coefficients for the case n does not = 0. In case of Landau resonance, the values of Dpp coefficient are generally larger than the values of D alpha coefficients particularly at lower energies. As an aid to the interpretation of results, we have also determined the resonant frequencies. For ECH waves, resonant frequencies have been estimated for wave normal angle 89 deg and harmonic resonances n = +1, +2, and +3, whereas for whistler mode waves, the frequencies have been calculated for angle 10 deg and Landau resonance. Further, in ECH waves, the banded structures appear for electron energies (is) greater than1 keV, and for whistler mode chorus waves, structures appear for energies greater than 2 keV at L = 4.6 and above 200 eV for L = 6.8. The results obtained in the present work will be helpful in the study of diffusion curves and will have important consequences for diffuse aurora and pancake distributions.

Banded Structures in Electron Pitch Angle Diffusion Coefficients from Resonant Wave-Particle Interactions

NASA Technical Reports Server (NTRS)

Tripathi, A. K.; Singhal, R. P.; Khazanov, G. V.; Avanov, L. A.

2016-01-01

Electron pitch angle (D(sub (alpha alpha))) and momentum (D(sub pp)) diffusion coefficients have been calculated due to resonant interactions with electrostatic electron cyclotron harmonic (ECH) and whistler mode chorus waves. Calculations have been performed at two spatial locations L=4.6 and 6.8 for electron energies less than or equal to 10 keV. Landau (n=0) resonance and cyclotron harmonic resonances n= +/- 1, +/-2, ... +/-5 have been included in the calculations. It is found that diffusion coefficient versus pitch angle (alpha) profiles show large dips and oscillations or banded structures. The structures are more pronounced for ECH and lower band chorus (LBC) and particularly at location 4.6. Calculations of diffusion coefficients have also been performed for individual resonances. It is noticed that the main contribution of ECH waves in pitch angle diffusion coefficient is due to resonances n=+1 and n=+2. A major contribution to momentum diffusion coefficients appears from n=+2. However, the banded structures in D(sub alpha alpha) and D(sub pp) coefficients appear only in the profile of diffusion coefficients for n=+2. The contribution of other resonances to diffusion coefficients is found to be, in general, quite small or even negligible. For LBC and upper band chorus waves, the banded structures appear only in Landau resonance. The D(sub pp) diffusion coefficient for ECH waves is one to two orders smaller than D(sub alpha alpha) coefficients. For chorus waves, D(sub pp) coefficients are about an order of magnitude smaller than D(sub alpha alpha) coefficients for the case n does not equal 0. In case of Landau resonance, the values of D(sub pp) coefficient are generally larger than the values of D(sub alpha alpha) coefficients particularly at lower energies. As an aid to the interpretation of results, we have also determined the resonant frequencies. For ECH waves, resonant frequencies have been estimated for wave normal angle 89 deg and harmonic resonances n= +1, +2, and +3, whereas for whistler mode waves, the frequencies have been calculated for angle 10 deg and Landau resonance. Further, in ECH waves, the banded structures appear for electron energies 1 greater than or equal to keV, and for whistler mode chorus waves, structures appear for energies greater than 2 keV at L=4.6 and above 200 eV for L=6.8. The results obtained in the present work will be helpful in the study of diffusion curves and will have important consequences for diffuse aurora and pancake distributions.

Development And Test of A Digitally Steered Antenna Array for The Navigator GPS Receiver

NASA Technical Reports Server (NTRS)

Pinto, Heitor David; Valdez, Jennifer E.; Winternitz, Luke M. B.; Hassouneh, Munther A.; Price, Samuel R.

2012-01-01

Global Positioning System (GPS)-based navigation has become common for low-Earth orbit spacecraft as the signal environment is similar to that on the Earth s surface. The situation changes abruptly, however, for spacecraft whose orbital altitudes exceed that of the GPS constellation. Visibility is dramatically reduced and signals that are present may be very weak and more susceptible to interference. GPS receivers effective at these altitudes require increased sensitivity, which often requires a high-gain antenna. Pointing such an antenna can pose a challenge. One efficient approach to mitigate these problems is the use of a digitally steered antenna array. Such an antenna can optimally allocate gain toward desired signal sources and away from interferers. This paper presents preliminary results in the development and test of a digitally steered antenna array for the Navigator GPS research program at NASA s Goddard Space Flight Center. In particular, this paper highlights the development of an array and front-end electronics, the development and test of a real-time software GPS receiver, and implementation of three beamforming methods for combining the signals from the array. Additionally, this paper discusses the development of a GPS signal simulator which produces digital samples of the GPS L1C/A signals as they would be received by an arbitrary antenna array configuration. The simulator models transmitter and receiver dynamics, near-far and multipath interference, and has been a critical component in both the development and test of the GPS receiver. The GPS receiver system was tested with real and simulated GPS signals. Preliminary results show that performance improvement was achieved in both the weak signal and interference environments, matching analytical predictions. This paper summarizes our initial findings and discusses the advantages and limitations of the antenna array and the various beamforming methods.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell Feder and Mahmoud Z. Yousef

Neutronics analysis to find nuclear heating rates and personnel dose rates were conducted in support of the integration of diagnostics in to the ITER Upper Port Plugs. Simplified shielding models of the Visible-Infrared diagnostic and of the ECH heating system were incorporated in to the ITER global CAD model. Results for these systems are representative of typical designs with maximum shielding and a small aperture (Vis-IR) and minimal shielding with a large aperture (ECH). The neutronics discrete-ordinates code ATTILA® and SEVERIAN® (the ATTILA parallel processing version) was used. Material properties and the 500 MW D-T volume source were taken frommore » the ITER “Brand Model” MCNP benchmark model. A biased quadrature set equivelant to Sn=32 and a scattering degree of Pn=3 were used along with a 46-neutron and 21-gamma FENDL energy subgrouping. Total nuclear heating (neutron plug gamma heating) in the upper port plugs ranged between 380 and 350 kW for the Vis-IR and ECH cases. The ECH or Large Aperture model exhibited lower total heating but much higher peak volumetric heating on the upper port plug structure. Personnel dose rates are calculated in a three step process involving a neutron-only transport calculation, the generation of activation volume sources at pre-defined time steps and finally gamma transport analyses are run for selected time steps. ANSI-ANS 6.1.1 1977 Flux-to-Dose conversion factors were used. Dose rates were evaluated for 1 full year of 500 MW DT operation which is comprised of 3000 1800-second pulses. After one year the machine is shut down for maintenance and personnel are permitted to access the diagnostic interspace after 2-weeks if dose rates are below 100 μSv/hr. Dose rates in the Visible-IR diagnostic model after one day of shutdown were 130 μSv/hr but fell below the limit to 90 μSv/hr 2-weeks later. The Large Aperture or ECH style shielding model exhibited higher and more persistent dose rates. After 1-day the dose rate was 230 μSv/hr but was still at 120 μSv/hr 4-weeks later. __________________________________________________« less

Survey of upper band chorus and ECH waves: Implications for the diffuse aurora

NASA Astrophysics Data System (ADS)

Meredith, Nigel; Horne, Richard; Thorne, Richard; Anderson, Roger

2010-05-01

The origin of the diffuse aurora has been a source of controversy for many years. More recently the question has taken a new significance in view of the associated changes in atmospheric chemistry which may affect the middle atmosphere. Here we use CRRES data to assess the importance of upper band chorus and electron cyclotron harmonic (ECH) waves in the production of the diffuse aurora. Both wave modes increase with increasing geomagnetic activity, suggesting they are related to periods of enhanced convection and/or substorm activity. They are confined to the near-equatorial region which excludes the pre-noon sector from the wave survey. During active conditions intense ECH waves and upper band chorus, with amplitudes exceeding 1 mVm-1, are observed in the region 4 < L < 7 from 2100 to 0600 MLT approximately 20% and 6% of the time respectively. This suggests that both wave modes can put electrons on strong diffusion, but only during active conditions and not at all local times. Scattering rates fall below the strong diffusion limit at other times when the wave amplitudes are weaker. Fluxes of low energy electrons (100 eV < E < 30 keV) also increase with increasing geomagnetic activity in approximately the same region of geospace as the waves, suggesting that these electrons are responsible for the generation of the waves. The patterns of the upper band chorus, ECH waves and low energy electrons are similar to the global morphology of the diffuse aurora, suggesting that both wave modes play significant roles in the production of the diffuse aurora.

Nutritional Ingredients Modulate Adipokine Secretion and Inflammation in Human Primary Adipocytes

PubMed Central

Romacho, Tania; Glosse, Philipp; Richter, Isabel; Elsen, Manuela; Schoemaker, Marieke H.; van Tol, Eric A.; Eckel, Jürgen

2015-01-01

Nutritional factors such as casein hydrolysates and long chain polyunsaturated fatty acids have been proposed to exert beneficial metabolic effects. We aimed to investigate how a casein hydrolysate (eCH) and long chain polyunsaturated fatty acids could affect human primary adipocyte function in vitro. Incubation conditions with the different nutritional factors were validated by assessing cell vitality with lactate dehydrogenase (LDH) release and neutral red incorporation. Intracellular triglyceride content was assessed with Oil Red O staining. The effect of eCH, a non-peptidic amino acid mixture (AA), and long-chain polyunsaturated fatty acids (LC-PUFAs) on adiponectin and leptin secretion was determined by enzyme-linked immunosorbent assay (ELISA). Intracellular adiponectin expression and nuclear factor-κB (NF-κB) activation were analyzed by Western blot, while monocyte chemoattractant protein-1 (MCP-1) release was explored by ELISA. The eCH concentration dependently increased adiponectin secretion in human primary adipocytes through its intrinsic peptide bioactivity, since the non-peptidic mixture, AA, could not mimic eCH’s effects on adiponectin secretion. Eicosapentaenoic acid (EPA), docosahexaenoic acid (DHA), and DHA combined with arachidonic acid (ARA) upregulated adiponectin secretion. However, only DHA and DHA/ARA exerted a potentanti-inflammatory effect reflected by prevention of tumor necrosis factor-α (TNF-α) induced NF-κB activation and MCP-1 secretion in human adipocytes. eCH and DHA alone or in combination with ARA, may hold the key for nutritional programming through their anti-inflammatory action to prevent diseases with low-grade chronic inflammation such as obesity or diabetes. PMID:25629558

Trace analysis of parabens preservatives in drinking water treatment sludge, treated, and mineral water samples.

PubMed

Marta-Sanchez, Ana Victoria; Caldas, Sergiane Souza; Schneider, Antunielle; Cardoso, Sónia Maria Vaz Sanches; Primel, Ednei Gilberto

2018-05-01

Parabens have been widely used as antimicrobial agents, mainly in food products, pharmaceuticals, and cosmetics. Although they are known as safe preservatives, they also cause some harm to human health, which has been discussed lately. Therefore, the aim of this study was to evaluate the occurrence of nine parabens (including isomers) in mineral and drinking waters, besides in drinking water treatment sludge (DWTS) samples with determination by liquid chromatography tandem mass spectrometry (LC-MS/MS). Both methods solid phase extraction (SPE) and QuEChERS were validated. Calibration curves showed a correlation coefficient of 0.99 for all compounds. LOQ values ranged from 0.04 to 4 μg L -1 in aqueous matrices and from 5 to 500 ng g -1 in DWTS. Recoveries between 70 and 115% were reached with RSD below 20% for all compounds in SPE whereas recoveries between 62 and 119% were found with RSD below 20% for almost all compounds in QuEChERS. Matrix effect had low values (< 20%); it was only above 20% for methylparaben in the SPE and for pentylparaben in the QuEChERS. Using a quick and simple extraction procedures with SPE, QuEChERS, and LC-MS/MS analyses, these methods proved to be selective and sensitive. They were successfully applied to real samples (treated water, mineral water, and sludge), and methylparaben was detected at concentration levels below 0.242 μg L -1 in mineral and treated water samples and 10 ng g -1 in DWTS samples.

EChO fine guidance sensor design and architecture

NASA Astrophysics Data System (ADS)

Ottensamer, Roland; Rataj, Miroslaw; Schrader, Jan-Rutger; Ferstl, Roman; Güdel, Manuel; Kerschbaum, Franz; Luntzer, Armin

2014-08-01

EChO, the Exoplanet Characterization Observatory, is an M-class candidate in the ESA Comic Vision programme. It will provide high resolution, multi-wavelength spectroscopic observations of exoplanets, measure their atmospheric composition, temperature and albedo. The scientific payload is a spectrometer covering the 0.4-11 micron waveband. High photometric stability over a time scale of about 10 hours is one of the most stringent requirements of the EChO mission. As a result, fine pointing stability relative to the host star is mandatory. This will be achieved through a Fine Guidance Sensor (FGS), a separate photometric channel that uses a fraction of the target star signal from the optical channel. The main task of the FGS is to ensure the centering, focusing and guiding of the satellite, but it will also provide supplemental high-precision astrometry and photometry of the target to ground for de-trending the spectra and complementary science. In this paper we give an overview of the current architectural design of the FGS subsystem and discuss related requirements as well as the expected performance.

Improved cross-calibration of Thomson scattering and electron cyclotron emission with ECH on DIII-D

DOE PAGES

Brookman, M. W.; Austin, M. E.; McLean, A. G.; ...

2016-08-08

Thomson scattering (TS) produces n e profiles from measurement of scattered laser beam intensity. In the case of Rayleigh scattering, it provides a first calibration of the relation n e / ITS, which depends on many factors (e.g. laser alignment and power, optics, and measurement systems). On DIII-D, the n e calibration is adjusted for each laser and optic path against an absolute n e measurement from a density-driven cutoff on the 48 channel 2nd harmonic X-mode electron cyclotron emission (ECE) system. This method has been used to calibrate Thompson densities from the edge to near the core (r/a >more » 0.15). Application of core electron cyclotron heating improves the quality of cutoff and depth of its penetration into the core. ECH also changes underlying MHD activity. Furthermore, on the removal of ECH power, cutoff penetrates in from the edge to the core and channels fall successively and smoothly into cutoff. This improves the quality of the TS n e calibration while minimizing wall loading.« less

Validation of QuEChERS method for the determination of some pesticide residues in two apple varieties.

PubMed

Tiryaki, Osman

2016-10-02

This study was undertaken to validate the "quick, easy, cheap, effective, rugged and safe" (QuEChERS) method using Golden Delicious and Starking Delicious apple matrices spiked at 0.1 maximum residue limit (MRL), 1.0 MRL and 10 MRL levels of the four pesticides (chlorpyrifos, dimethoate, indoxacarb and imidacloprid). For the extraction and cleanup, original QuEChERS method was followed, then the samples were subjected to liquid chromatography-triple quadrupole mass spectrometry (LC-MS/MS) for chromatographic analyses. According to t test, matrix effect was not significant for chlorpyrifos in both sample matrices, but it was significant for dimethoate, indoxacarb and imidacloprid in both sample matrices. Thus, matrix-matched calibration (MC) was used to compensate matrix effect and quantifications were carried out by using MC. The overall recovery of the method was 90.15% with a relative standard deviation of 13.27% (n = 330). Estimated method detection limit of analytes blew the MRLs. Some other parameters of the method validation, such as recovery, precision, accuracy and linearity were found to be within the required ranges.

Modified QuEChERS combined with ultra high performance liquid chromatography tandem mass spectrometry to determine seven biogenic amines in Chinese traditional condiment soy sauce.

PubMed

Dong, Hao; Xiao, Kaijun

2017-08-15

A rapid and sensitive UHPLC-MS/MS method followed by modified QuEChERS was developed for the simultaneous determination of seven biogenic amines in soy sauce. Samples were firstly diluted by water and pH values of which were adjusted using ammonia water. Modified QuEChERS method was adopted for the purification and 1, 7-heptyldiamine was used as the internal standard. Analysis of seven biogenic amines was within 4min. Under the optimized conditions, linear relations were favorable over the selected concentration ranges of 3.0-600μg/L with correlationcoefficients greater than 0.999. The average accuracy was between 84% and 115%. Intra- and inter- assay precisions for six replicates ranged from 2.2% to 8.8% or below 12%, respectively. The method limits of detection and the method limits of quantitation were 4-8μg/kg and 15-30μg/kg, respectively. The method was successfully applied to determine the concentrations of seven biogenic amines in soy sauces. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of mycotoxins in plant-based beverages using QuEChERS and liquid chromatography-tandem mass spectrometry.

PubMed

Miró-Abella, Eugènia; Herrero, Pol; Canela, Núria; Arola, Lluís; Borrull, Francesc; Ras, Rosa; Fontanals, Núria

2017-08-15

A method was developed for the simultaneous determination of 11 mycotoxins in plant-based beverage matrices, using a QuEChERS extraction followed by ultra-high performance liquid chromatography coupled to tandem mass spectrometry detection (UHPLC-(ESI)MS/MS). This multi-mycotoxin method was applied to analyse plant-based beverages such as soy, oat and rice. QuEChERS extraction was applied obtaining suitable extraction recoveries between 80 and 91%, and good repeatability and reproducibility values. Method Quantification Limits were between 0.05μgL -1 (for aflatoxin G 1 and aflatoxin B 1 ) and 15μgL -1 (for deoxynivalenol and fumonisin B 2 ). This is the first time that plant-based beverages have been analysed, and certain mycotoxins, such as deoxynivalenol, aflatoxin B 1 , aflatoxin B 2 , aflatoxin G 1 , aflatoxin G 2 , ochratoxin A, T-2 toxin and zearalenone, were found in the analysed samples, and some of them quantified between 0.1μgL -1 and 19μgL -1 . Copyright © 2017 Elsevier Ltd. All rights reserved.

QuEChERS Purification Combined with Ultrahigh-Performance Liquid Chromatography Tandem Mass Spectrometry for Simultaneous Quantification of 25 Mycotoxins in Cereals

PubMed Central

Sun, Juan; Li, Weixi; Zhang, Yan; Hu, Xuexu; Wu, Li; Wang, Bujun

2016-01-01

A method based on the QuEChERS (quick, easy, cheap, effective, rugged, and safe) purification combined with ultrahigh performance liquid chromatography tandem mass spectrometry (UPLC–MS/MS), was optimized for the simultaneous quantification of 25 mycotoxins in cereals. Samples were extracted with a solution containing 80% acetonitrile and 0.1% formic acid, and purified with QuEChERS before being separated by a C18 column. The mass spectrometry was conducted by using positive electrospray ionization (ESI+) and multiple reaction monitoring (MRM) models. The method gave good linear relations with regression coefficients ranging from 0.9950 to 0.9999. The detection limits ranged from 0.03 to 15.0 µg·kg−1, and the average recovery at three different concentrations ranged from 60.2% to 115.8%, with relative standard deviations (RSD%) varying from 0.7% to 19.6% for the 25 mycotoxins. The method is simple, rapid, accurate, and an improvement compared with the existing methods published so far. PMID:27983693

A High Throughput Method for Measuring Polycyclic Aromatic Hydrocarbons in Seafood Using QuEChERS Extraction and SBSE.

PubMed

Pfannkoch, Edward A; Stuff, John R; Whitecavage, Jacqueline A; Blevins, John M; Seely, Kathryn A; Moran, Jeffery H

2015-01-01

National Oceanic and Atmospheric Administration (NOAA) Method NMFS-NWFSC-59 2004 is currently used to quantitatively analyze seafood for polycyclic aromatic hydrocarbon (PAH) contamination, especially following events such as the Deepwater Horizon oil rig explosion that released millions of barrels of crude oil into the Gulf of Mexico. This method has limited throughput capacity; hence, alternative methods are necessary to meet analytical demands after such events. Stir bar sorptive extraction (SBSE) is an effective technique to extract trace PAHs in water and the quick, easy, cheap, effective, rugged, and safe (QuEChERS) extraction strategy effectively extracts PAHs from complex food matrices. This study uses SBSE to concentrate PAHs and eliminate matrix interference from QuEChERS extracts of seafood, specifically oysters, fish, and shrimp. This method provides acceptable recovery (65-138%) linear calibrations and is sensitive (LOD = 0.02 ppb, LOQ = 0.06 ppb) while providing higher throughput and maintaining equivalency between NOAA 2004 as determined by analysis of NIST SRM 1974b mussel tissue.

Decoupling control of vehicle chassis system based on neural network inverse system

NASA Astrophysics Data System (ADS)

Wang, Chunyan; Zhao, Wanzhong; Luan, Zhongkai; Gao, Qi; Deng, Ke

2018-06-01

Steering and suspension are two important subsystems affecting the handling stability and riding comfort of the chassis system. In order to avoid the interference and coupling of the control channels between active front steering (AFS) and active suspension subsystems (ASS), this paper presents a composite decoupling control method, which consists of a neural network inverse system and a robust controller. The neural network inverse system is composed of a static neural network with several integrators and state feedback of the original chassis system to approach the inverse system of the nonlinear systems. The existence of the inverse system for the chassis system is proved by the reversibility derivation of Interactor algorithm. The robust controller is based on the internal model control (IMC), which is designed to improve the robustness and anti-interference of the decoupled system by adding a pre-compensation controller to the pseudo linear system. The results of the simulation and vehicle test show that the proposed decoupling controller has excellent decoupling performance, which can transform the multivariable system into a number of single input and single output systems, and eliminate the mutual influence and interference. Furthermore, it has satisfactory tracking capability and robust performance, which can improve the comprehensive performance of the chassis system.

Prototype Development of the GMT Fast Steering Mirror

NASA Astrophysics Data System (ADS)

Kim, Young-Soo; Koh, J.; Jung, H.; Jung, H.; Cho, M. K.; Park, W.; Yang, H.; Kim, H.; Lee, K.; Ahn, H.; Park, B.

2014-01-01

A Fast Steering Mirror (FSM) is going to be provided as the secondary of the Giant Magellan Telescope (GMT) for the first light observations. FSM is 3.2 m in diameter and the focal ratio is 0.65. It is composed of seven circular segments which match with the primary mirror segments. Each segment contains a light-weighted mirror whose diameter is 1.1 m, and each mirror is activated by three tip-tilt actuators which compensate image degradations caused by winds and structure jitter. An FSM prototype (FSMP) has been developed to achieve the key technologies, fabrication of highly aspheric off-axis mirror and precise tip-tilt actuation. It consists of a full-size off-axis mirror segment and a tip-tilt test-bed. The development has been conducted by Korea Astronomy and Space Science Institute together with four other institutions in Korea and USA. The mirror was light-weighted by digging about a hundred holes at the backside, and the front surface has been polished. The result of computer generated hologram measurements showed the surface error of 11.7 nm rms. The tip-tilt test-bed has been manufactured and assembled. Tip-tilt range and resolution tests complied the requirements, and the attenuation test results also satisfied the performance requirements. In this paper, we present the successful developments of the prototype.

Study of a high-resolution, 3-D positioning cadmium zinc telluride detector for PET

PubMed Central

Gu, Y; Matteson, J L; Skelton, R T; Deal, A C; Stephan, E A; Duttweiler, F; Gasaway, T M; Levin, C S

2011-01-01

This paper investigates the performance of 1 mm resolution Cadmium Zinc Telluride (CZT) detectors for positron emission tomography (PET) capable of positioning the 3-D coordinates of individual 511 keV photon interactions. The detectors comprise 40 mm × 40 mm × 5 mm monolithic CZT crystals that employ a novel cross-strip readout with interspersed steering electrodes to obtain high spatial and energy resolution. The study found a single anode FWHM energy resolution of 3.06±0.39% at 511 keV throughout most the detector volume. Improved resolution is expected with properly shielded front-end electronics. Measurements made using a collimated beam established the efficacy of the steering electrodes in facilitating enhanced charge collection across anodes, as well as a spatial resolution of 0.44±0.07 mm in the direction orthogonal to the electrode planes. Finally, measurements based on coincidence electronic collimation yielded a point spread function with 0.78±0.10 mm FWHM, demonstrating 1 mm spatial resolution capability transverse to the anodes – as expected from the 1 mm anode pitch. These findings indicate that the CZT-based detector concept has excellent performance and shows great promise for a high-resolution PET system. PMID:21335649

Banded structures in electron pitch angle diffusion coefficients from resonant wave-particle interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tripathi, A. K., E-mail: aktrip2001@yahoo.co.in; Singhal, R. P., E-mail: rpsiitbhu@yahoo.com; Khazanov, G. V., E-mail: George.V.Khazanov@nasa.gov

2016-04-15

Electron pitch angle (D{sub αα}) and momentum (D{sub pp}) diffusion coefficients have been calculated due to resonant interactions with electrostatic electron cyclotron harmonic (ECH) and whistler mode chorus waves. Calculations have been performed at two spatial locations L = 4.6 and 6.8 for electron energies ≤10 keV. Landau (n = 0) resonance and cyclotron harmonic resonances n = ±1, ±2, … ±5 have been included in the calculations. It is found that diffusion coefficient versus pitch angle (α) profiles show large dips and oscillations or banded structures. The structures are more pronounced for ECH and lower band chorus (LBC) and particularly at location 4.6. Calculations of diffusionmore » coefficients have also been performed for individual resonances. It is noticed that the main contribution of ECH waves in pitch angle diffusion coefficient is due to resonances n = +1 and n = +2. A major contribution to momentum diffusion coefficients appears from n = +2. However, the banded structures in D{sub αα} and D{sub pp} coefficients appear only in the profile of diffusion coefficients for n = +2. The contribution of other resonances to diffusion coefficients is found to be, in general, quite small or even negligible. For LBC and upper band chorus waves, the banded structures appear only in Landau resonance. The D{sub pp} diffusion coefficient for ECH waves is one to two orders smaller than D{sub αα} coefficients. For chorus waves, D{sub pp} coefficients are about an order of magnitude smaller than D{sub αα} coefficients for the case n ≠ 0. In case of Landau resonance, the values of D{sub pp} coefficient are generally larger than the values of D{sub αα} coefficients particularly at lower energies. As an aid to the interpretation of results, we have also determined the resonant frequencies. For ECH waves, resonant frequencies have been estimated for wave normal angle 89° and harmonic resonances n = +1, +2, and +3, whereas for whistler mode waves, the frequencies have been calculated for angle 10° and Landau resonance. Further, in ECH waves, the banded structures appear for electron energies ≥1 keV, and for whistler mode chorus waves, structures appear for energies >2 keV at L = 4.6 and above 200 eV for L = 6.8. The results obtained in the present work will be helpful in the study of diffusion curves and will have important consequences for diffuse aurora and pancake distributions.« less

Advanced Wavefront Sensing and Control Testbed (AWCT)

NASA Technical Reports Server (NTRS)

Shi, Fang; Basinger, Scott A.; Diaz, Rosemary T.; Gappinger, Robert O.; Tang, Hong; Lam, Raymond K.; Sidick, Erkin; Hein, Randall C.; Rud, Mayer; Troy, Mitchell

2010-01-01

The Advanced Wavefront Sensing and Control Testbed (AWCT) is built as a versatile facility for developing and demonstrating, in hardware, the future technologies of wave front sensing and control algorithms for active optical systems. The testbed includes a source projector for a broadband point-source and a suite of extended scene targets, a dispersed fringe sensor, a Shack-Hartmann camera, and an imaging camera capable of phase retrieval wavefront sensing. The testbed also provides two easily accessible conjugated pupil planes which can accommodate the active optical devices such as fast steering mirror, deformable mirror, and segmented mirrors. In this paper, we describe the testbed optical design, testbed configurations and capabilities, as well as the initial results from the testbed hardware integrations and tests.

Design of an unified chassis controller for rollover prevention, manoeuvrability and lateral stability

NASA Astrophysics Data System (ADS)

Yoon, Jangyeol; Yim, Seongjin; Cho, Wanki; Koo, Bongyeong; Yi, Kyongsu

2010-11-01

This paper describes a unified chassis control (UCC) strategy to prevent vehicle rollover and improve both manoeuvrability and lateral stability. Since previous researches on rollover prevention are only focused on the reduction of lateral acceleration, the manoeuvrability and lateral stability cannot be guaranteed. For this reason, it is necessary to design a UCC controller to prevent rollover and improve lateral stability by integrating electronic stability control, active front steering and continuous damping control. This integration is performed through switching among several control modes and a simulation is performed to validate the proposed method. Simulation results indicate that a significant improvement in rollover prevention, manoeuvrability and lateral stability can be expected from the proposed UCC system.

The beluga whale produces two pulses to form its sonar signal

PubMed Central

Lammers, Marc O.; Castellote, Manuel

2009-01-01

Odontocete cetaceans use biosonar clicks to acoustically probe their aquatic environment with an aptitude unmatched by man-made sonar. A cornerstone of this ability is their use of short, broadband pulses produced in the region of the upper nasal passages. Here we provide empirical evidence that a beluga whale (Delphinapterus leucas) uses two signal generators simultaneously when echolocating. We show that the pulses of the two generators are combined as they are transmitted through the melon to produce a single echolocation click emitted from the front of the animal. Generating two pulses probably offers the beluga the ability to control the energy and frequency distribution of the emitted click and may allow it to acoustically steer its echolocation beam. PMID:19324643

Electron Bernstein Wave Emission Studies on the TJ-II Stellarator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caughman, John B; Fernandez, A.; Cappa, A.

2009-01-01

Electron Bernstein Wave (EBW) heating is important for high-beta plasma experiments and will be used for heating over-dense plasmas on TJ-II. TJ-II is a medium sized Heliac operating at CIEMAT in Madrid, whose plasmas are created and heated by ECH via two 300 kW gyrotrons at second harmonic X-mode (53.2 GHz), with additional heating provided by two neutral beam injectors. Theoretical work has shown that the most suitable scheme for launching EBWs in TJ-II is O-X-B mode conversion, which has acceptable heating efficiency for central densities above 1.2 x 1019 m-3.[1] A system based on a 28 GHz-100ms diode gyrotronmore » will be used to deliver 300 kW through a corrugated waveguide. The microwave heating beam will be directed and focused by a steering mirror located inside the vacuum vessel. Prior to the heating experiments, measurement of the thermal EBW emission (EBE) from the plasma is being made to help determine the optimum launch angle for EBW mode conversion, and also to provide an indication of the electron temperature evolution in over-dense plasmas. A dual-polarized quad-ridged broadband horn is used to measure the EBW emission and polarization at 28 GHz. Initial measurements indicate that the emission in under-dense plasmas corresponds to oblique electron cyclotron emission (ECE) and then converts to EBE when the plasma becomes over-dense during neutral beam injection.« less

Lethal and sublethal toxicity of the industrial chemical epichlorohydrin on Rhinella arenarum (Anura, Bufonidae) embryos and larvae.

PubMed

Hutler Wolkowicz, Ianina R; Aronzon, Carolina M; Pérez Coll, Cristina S

2013-12-15

Lethal and sublethal toxicity of the major chemical used in epoxide compounds, epichlorohydrin (ECH) was evaluated on the early life cycle of the common South American toad, Rhinella arenarum (Anura, Bufonidae). The stages evaluated were (according to Del Conte and Sirlin): early blastula (S.3-S.4), gastrula (S.10-S.12), rotation (S.15), tail bud (S.17), muscular response (S.18), gill circulation (S.20), open mouth (S.21), opercular folds (S.23) and complete operculum (S.25). The LC50 and EC50 values for lethal and sublethal effects were calculated. The early blastula was the most sensitive stage to ECH both for continuously and pulse-exposures (LC50-24h=50.9 mg L(-1)), while S.20 was the most resistant (LC50-24h=104.9 mg L(-1)). Among sublethal effects, early blastula was also the most sensitive stage (LOEC-48 h=20 mg L(-1)) and it has a Teratogenic Index of 2.5, which indicates the teratogenic potential of the substance. The main abnormalities were persistent yolk plugs, cell dissociation, tumors, hydropsy, oral malformations, axial/tail flexures, delayed development and reduced body size. ECH also caused neurotoxicity including scarce response to stimuli, reduction in the food intake, general weakness, spasms and shortening, erratic or circular swimming. Industrial contamination is considered an important factor on the decline of amphibian populations. Considering the available information about ECH's toxicity and its potential hazard to the environment, this work shows the first results of its developmental toxicity on a native amphibian species, Rhinella arenarum. Copyright © 2013 Elsevier B.V. All rights reserved.

Identification and Functional Characterization of a Novel Monotreme- Specific Antibacterial Protein Expressed during Lactation

PubMed Central

Bisana, Swathi; Kumar, Satish; Rismiller, Peggy; Nicol, Stewart C.; Lefèvre, Christophe; Nicholas, Kevin R.; Sharp, Julie A.

2013-01-01

Monotremes are the only oviparous mammals and exhibit a fascinating combination of reptilian and mammalian characters. They represent a component of synapsidal reproduction by laying shelled eggs which are incubated outside the mother’s body. This is accompanied by a prototherian lactation process, marking them as representatives of early mammals. The only extant monotremes are the platypus, and the short- and long- beaked echidnas, and their distributions are limited to Australia and New Guinea. Apart for a short weaning period, milk is the sole source of nutrition and protection for the hatchlings which are altricial and immunologically naive. The duration of lactation in these mammals is prolonged relative to the gestational length and period of incubation of eggs. Much of the development of monotreme young occurs in the non-sterile ex-utero environment. Therefore the role of milk in the growth, development and disease protection of the young is of significant interest. By sequencing the cDNA of cells harvested from monotreme milk, we have identified a novel monotreme- specific transcript, and the corresponding gene was designated as the EchAMP. The expression profile of this gene in various tissues revealed that it is highly expressed in milk cells. The peptides corresponding to the EchAMP protein have been identified in a sample of echidna milk In silico analysis indicated putative antimicrobial potential for the cognate protein of EchAMP. This was further confirmed by in vitro assays using a host of bacteria. Interestingly, EchAMP did not display any activity against a commensal gut floral species. These results support the hypothesis of enhancement of survival of the young by antimicrobial bioactives of mammary gland origin and thus emphasize the protective, non- nutritional role of milk in mammals. PMID:23326486

Influence of demineralized bone matrix's embryonic origin on bone formation: an experimental study in rats.

PubMed

Stavropoulos, Andreas; Kostopoulos, Lambros; Mardas, Nicolaos; Karring, Thorkild

2003-01-01

There are results suggesting that differences regarding bone-inducing potential, in terms of amount and/or rate of bone formation, exist between demineralized bone matrices (DBMs) of different embryonic origins. The aim of the present study was to examine whether the embryonic origin of DBM affects bone formation when used as an adjunct to guided tissue regeneration (GTR). Endomembranous (EM) and endochondral (ECH) DBMs were produced from calvarial and long bones of rats, respectively. Prior to the study the osteoinductive properties of the DBMs were confirmed in six rats following intramuscular implantation. Following surgical exposure of the mandibular ramus, a rigid hemispheric Teflon capsule loosely packed with a standardized quantity of DBM was placed with its open part facing the lateral surface of the ramus in both sides of the jaw in 30 rats. In one side of the jaw, chosen at random, the capsule was filled with EM-DBM, whereas in the other side ECH-DBM was used. Groups of 10 animals were sacrificed after healing periods of 1, 2, and 4 months, and undecalcified sections of the capsules were produced and subjected to histologic analysis and computer-assisted planimetric measurements. During the experiment increasing amounts of newly formed bone were observed inside the capsules in both sides of the animals' jaws. Limited bone formation was observed in the 1- and 2-month specimens, but after 4 months of healing, the newly formed bone in the ECH-DBM grafted sides occupied 59.1% (range 45.6-74.7%) of the area created by the capsule versus 46.9% (range 23.0-64.0%) in the EM-DBM grafted sides (p =.01). It is concluded that the embryonic origin of DBM influences bone formation by GTR and that ECH-DBM is superior to EM-DBM.

Development and application of a ray-tracing code integrating with 3D equilibrium mapping in LHD ECH experiments

NASA Astrophysics Data System (ADS)

Tsujimura, T., Ii; Kubo, S.; Takahashi, H.; Makino, R.; Seki, R.; Yoshimura, Y.; Igami, H.; Shimozuma, T.; Ida, K.; Suzuki, C.; Emoto, M.; Yokoyama, M.; Kobayashi, T.; Moon, C.; Nagaoka, K.; Osakabe, M.; Kobayashi, S.; Ito, S.; Mizuno, Y.; Okada, K.; Ejiri, A.; Mutoh, T.

2015-11-01

The central electron temperature has successfully reached up to 7.5 keV in large helical device (LHD) plasmas with a central high-ion temperature of 5 keV and a central electron density of 1.3× {{10}19} m-3. This result was obtained by heating with a newly-installed 154 GHz gyrotron and also the optimisation of injection geometry in electron cyclotron heating (ECH). The optimisation was carried out by using the ray-tracing code ‘LHDGauss’, which was upgraded to include the rapid post-processing three-dimensional (3D) equilibrium mapping obtained from experiments. For ray-tracing calculations, LHDGauss can automatically read the relevant data registered in the LHD database after a discharge, such as ECH injection settings (e.g. Gaussian beam parameters, target positions, polarisation and ECH power) and Thomson scattering diagnostic data along with the 3D equilibrium mapping data. The equilibrium map of the electron density and temperature profiles are then extrapolated into the region outside the last closed flux surface. Mode purity, or the ratio between the ordinary mode and the extraordinary mode, is obtained by calculating the 1D full-wave equation along the direction of the rays from the antenna to the absorption target point. Using the virtual magnetic flux surfaces, the effects of the modelled density profiles and the magnetic shear at the peripheral region with a given polarisation are taken into account. Power deposition profiles calculated for each Thomson scattering measurement timing are registered in the LHD database. The adjustment of the injection settings for the desired deposition profile from the feedback provided on a shot-by-shot basis resulted in an effective experimental procedure.

Use of ammonium formate in QuEChERS for high-throughput analysis of pesticides in food by fast, low-pressure gas chromatography and liquid chromatography tandem mass spectrometry.

PubMed

González-Curbelo, Miguel Ángel; Lehotay, Steven J; Hernández-Borges, Javier; Rodríguez-Delgado, Miguel Ángel

2014-09-05

The "quick, easy, cheap, effective, rugged, and safe" (QuEChERS) approach to sample preparation is widely applied in pesticide residue analysis, but the use of magnesium sulfate and other nonvolatile compounds for salting out in the method is not ideal for mass spectrometry. In this study, we developed and evaluated three new different versions of the QuEChERS method using more volatile salts (ammonium chloride and ammonium formate and acetate buffers) to induce phase separation and extraction of 43 representative pesticide analytes of different classes. Fast low-pressure gas chromatography tandem mass spectrometry (LPGC-MS/MS) and liquid chromatography (LC)-MS/MS were used for analysis. The QuEChERS AOAC Official Method 2007.01 was also tested for comparison purposes. Of the studied methods, formate buffering using 7.5g of ammonium formate and 15mL of 5% (v/v) formic acid in acetonitrile for the extraction of 15g of sample (5g for wheat grain) provided the best performance and practical considerations. Method validation was carried out with and without the use of dispersive solid-phase extraction for cleanup, and no significant differences were observed for the majority of pesticides. The method was demonstrated in quantitative analysis for GC- and LC-amenable pesticides in 4 representative food matrices (apple, lemon, lettuce, and wheat grain). With the typical exceptions of certain pH-dependent and labile pesticides, 90-110% recoveries and <10% RSD were obtained. Detection limits were mostly <5ng/g, which met the general need to determine pesticide concentrations as low as 10ng/g for monitoring purposes in food applications. Published by Elsevier B.V.

Postweaning performance and carcass merit of F1 steers sired by Brahman and alternative subtropically adapted breeds.

PubMed

Franke, D E

1997-10-01

Comparisons were made among F1 steers sired by Brahman and alternative subtropically adapted breeds of bulls for feedlot and carcass traits when steers were produced from Angus- and Hereford-type dams. Brahman-derivative breeds included Brangus, Beefmaster, and Santa Gertrudis. Brangus- and Beefmaster-sired steers weighed less at slaughter, whereas carcasses of Brangus- and Santa Gertrudis-sired steers had more marbling than those of Brahman-sired steers. Brahman-sired steer carcasses had greater longissimus muscle area than carcasses of Santa Gertrudis-sired steers. Other Zebu breeds compared to Brahman were Boran, Gir, Indu-Brazil, Nellore, Red Brahman, and Sahiwal. Steers by Brahman sires had higher slaughter weights than steers by Boran, Gir, Nellore, or Sahiwal sires. Hot carcass weights of Brahman-sired steers were also higher than those of Boran- and Sahiwal-sired steers. Steer carcasses by Brahman sires had greater longissimus muscle area than those of steers by Sahiwal sires. Non-Zebu breeds included Tuli and Senepol. Steers by Tuli sires grew slower, had lower slaughter weights, and their carcasses weighed less than those of Brahman-sired steers. Brahman-sired steer carcasses had greater longissimus muscle area but less marbling than carcasses of Tuli-sired steers. These data suggest that steers by Brahman sires have an advantage for slaughter weight over steers by Brangus, Beefmaster, Boran, Gir, Nellore, Sahiwal, and Tuli sires, but their carcasses are at a disadvantage for marbling score compared with those by Brangus, Boran, Nellore, and Tuli sires.

A new model to compute the desired steering torque for steer-by-wire vehicles and driving simulators

NASA Astrophysics Data System (ADS)

Fankem, Steve; Müller, Steffen

2014-05-01

This paper deals with the control of the hand wheel actuator in steer-by-wire (SbW) vehicles and driving simulators (DSs). A novel model for the computation of the desired steering torque is presented. The introduced steering torque computation does not only aim to generate a realistic steering feel, which means that the driver should not miss the basic steering functionality of a modern conventional steering system such as an electric power steering (EPS) or hydraulic power steering (HPS), and this in every driving situation. In addition, the modular structure of the steering torque computation combined with suitably selected tuning parameters has the objective to offer a high degree of customisability of the steering feel and thus to provide each driver with his preferred steering feel in a very intuitive manner. The task and the tuning of each module are firstly described. Then, the steering torque computation is parameterised such that the steering feel of a series EPS system is reproduced. For this purpose, experiments are conducted in a hardware-in-the-loop environment where a test EPS is mounted on a steering test bench coupled with a vehicle simulator and parameter identification techniques are applied. Subsequently, how appropriate the steering torque computation mimics the test EPS system is objectively evaluated with respect to criteria concerning the steering torque level and gradient, the feedback behaviour and the steering return ability. Finally, the intuitive tuning of the modular steering torque computation is demonstrated for deriving a sportier steering feel configuration.

Production systems comparing early weaning to normal weaning with or without creep feeding for beef steers.

PubMed

Myers, S E; Faulkner, D B; Ireland, F A; Berger, L L; Parrett, D F

1999-02-01

A 2-yr study was conducted to determine the effects of three weaning management systems on cow and steer performance. Cow-calf pairs were randomly assigned to one of three treatments, in which the steer calves were 1) early-weaned (yr 1, 177 +/- 9 d; yr 2, 158 +/- 21 d of age) and placed on a finishing diet (EW), 2) supplemented with grain for 55 d on pasture (yr 1, 177 to 231 d; yr 2, 158 to 213 d of age) while nursing their dams and then placed on a finishing diet (NWC), and 3) on pasture for 55 d while nursing their dams (yr 1, 177 to 231 d; yr 2, 158 to 213 d of age) and then placed on a finishing diet (NW). In yr 2, potential breed differences were evaluated using steers of three breed types: 1) Angus x Hereford (BRI); 2) Angus x Simmental (CON); and 3) Angus x Wagyu (WAG). In yr 1, EW steers gained 100% faster (P = .0001) than the average of NWC and NW steers, and NWC steers gained 32% faster (P = .02) than NW steers before weaning. In the feedlot, EW steers had lower intakes (7.70 vs 8.16 kg/d, P = .008) and better feed conversions (.170 vs .153, P = .002) than the average of NWC and NW steers. Marbling score was improved for EW steers compared with the average of NWC and NW steers (P = .003). In yr 2, EW steers had higher gains (P = .0006) during the entire study than the average of NWC and NW steers, and NWC steers had higher gains (P = .003) than NW steers. The EW steers had lower intakes (7.29 vs 7.68 kg/d, P = .0008) and better feed conversions (.160 vs .141, P = .0001) than the average of NWC and NW steers. The CON steers were heavier at slaughter than BRI steers (P = .01), and BRI steers were heavier than WAG steers (P =.0004). Early weaning improved the percentage of steers grading Average Choice or higher by 40%. The percentage of BRI steers grading Choice or greater was 21% higher and percentage of steers grading Average Choice or greater was 33% higher than CON. Cows with EW steers had higher ADG than cows with NW steers (.38 vs -.17 kg/d, P = .0001) before weaning. Cows with EW steers gained in body condition score (.23 vs .00, P = .04), and cows with NW steers did not change. Early weaning improved feed efficiency and quality grades of beef steers.

A novel estimating method for steering efficiency of the driver with electromyography signals

NASA Astrophysics Data System (ADS)

Liu, Yahui; Ji, Xuewu; Hayama, Ryouhei; Mizuno, Takahiro

2014-05-01

The existing research of steering efficiency mainly focuses on the mechanism efficiency of steering system, aiming at designing and optimizing the mechanism of steering system. In the development of assist steering system especially the evaluation of its comfort, the steering efficiency of driver physiological output usually are not considered, because this physiological output is difficult to measure or to estimate, and the objective evaluation of steering comfort therefore cannot be conducted with movement efficiency perspective. In order to take a further step to the objective evaluation of steering comfort, an estimating method for the steering efficiency of the driver was developed based on the research of the relationship between the steering force and muscle activity. First, the steering forces in the steering wheel plane and the electromyography (EMG) signals of the primary muscles were measured. These primary muscles are the muscles in shoulder and upper arm which mainly produced the steering torque, and their functions in steering maneuver were identified previously. Next, based on the multiple regressions of the steering force and EMG signals, both the effective steering force and the total force capacity of driver in steering maneuver were calculated. Finally, the steering efficiency of driver was estimated by means of the estimated effective force and the total force capacity, which represented the information of driver physiological output of the primary muscles. This research develops a novel estimating method for driver steering efficiency of driver physiological output, including the estimation of both steering force and the force capacity of primary muscles with EMG signals, and will benefit to evaluate the steering comfort with an objective perspective.

Quantum steering in cascaded four-wave mixing processes.

PubMed

Wang, Li; Lv, Shuchao; Jing, Jietai

2017-07-24

Quantum steering is used to describe the "spooky action-at-a-distance" nonlocality raised in the Einstein-Podolsky-Rosen (EPR) paradox, which is important for understanding entanglement distribution and constructing quantum networks. Here, in this paper, we study an experimentally feasible scheme for generating quantum steering based on cascaded four-wave-mixing (FWM) processes in hot rubidium (Rb) vapor. Quantum steering, including bipartite steering and genuine tripartite steering among the output light fields, is theoretically analyzed. We find the corresponding gain regions in which the bipartite and tripartite steering exist. The results of bipartite steering can be used to establish a hierarchical steering model in which one beam can steer the other two beams in the whole gain region; however, the other two beams cannot steer the first beam simultaneously. Moreover, the other two beams cannot steer with each other in the whole gain region. More importantly, we investigate the gain dependence of the existence of the genuine tripartite steering and we find that the genuine tripartite steering exists in most of the whole gain region in the ideal case. Also we discuss the effect of losses on the genuine tripartite steering. Our results pave the way to experimental demonstration of quantum steering in cascaded FWM process.

Studies of electron-polyatomic-molecule collisions Applications to e-CH4

NASA Technical Reports Server (NTRS)

Lima, M. A. P.; Gibson, T. L.; Mckoy, V.; Huo, W. M.

1985-01-01

The first application of the Schwinger multichannel formulation to low-energy electron collisions with a nonlinear polyatomic target is reported. Integral and differential cross sections are obtained for e-CH4 collisions from 3 to 20 eV at the static-plus-exchange interaction level. In these studies, the exchange potential is directly evaluated and not approximated by local models. An interesting feature of the small-angle differential cross section is ascribed to polarization effects and not reproduced at the static-plus-exchange level. These differential cross sections are found to be in reasonable agreement with existing measurements at 7.5 eV and higher energies.

Stable sustainment of plasmas with electron internal transport barrier by ECH in the LHD

NASA Astrophysics Data System (ADS)

Yoshimura, Y.; Kasahara, H.; Tokitani, M.; Sakamoto, R.; Ueda, Y.; Marushchenko, N. B.; Seki, R.; Kubo, S.; Shimozuma, T.; Igami, H.; Takahashi, H.; Tsujimura, T. I.; Makino, R.; Kobayashi, S.; Ito, S.; Mizuno, Y.; Okada, K.; Akiyama, T.; Tanaka, K.; Tokuzawa, T.; Yamada, I.; Yamada, H.; Mutoh, T.; Takeiri, Y.; the LHD Experiment Group

2018-02-01

The long pulse experiments in the Large Helical Device has made progress in sustainment of improved confinement states. It was found that steady-state sustainment of the plasmas with improved confinement at the core region, that is, electron internal transport barrier (e-ITB), was achieved with no significant difficulty. Sustainment of a plasma having e-ITB with the line average electron density n e_ave of 1.1 × 1019 m-3 and the central electron temperature T e0 of ˜3.5 keV for longer than 5 min only with 340 kW ECH power was successfully demonstrated.

Application of recombinant Pediococcus acidilactici BD16 (fcs⁺/ech⁺) in malolactic fermentation.

PubMed

Kaur, Baljinder; Kumar, Balvir; Kaur, Gaganjot; Chakraborty, Debkumar; Kaur, Kiranjeet

2015-04-01

This study was conducted to enhance flavor characteristics of wine by malolactic fermentation using recombinant Pediococcus acidilactici BD16 (fcs (+)/ech (+)) encoding synthetic genes of feruloyl-CoA synthetase and enoyl-CoA hydratase. After malolactic fermentation, wine phenolics were characterized using LCMS-ESI technique and a significant improvement in the antioxidant activity and flavor characteristics of wine was observed due to increased concentration of cinnamic acid derivatives. This proof of concept study highlights the role of recombinant P. acidilactici BD16 (fcs (+)/ech (+)) in improving flavor as well as aroma of wine due to production of several phenolic derivatives during secondary fermentation. A novel metabolic pathway was predicted from mass spectral analysis data that indicates biotransformation of cinnamic acid and derivatives into apigenin, catechin, coniferyl aldehyde, cyanidin, hydroxybenzoic acids, laricitrin, luteolin, malvidin 3-glucoside, myricetin, naringenin, pelargonin, piceatannol, querecitin, and vanillin that not only increased the overall consumer appreciation but also improved nutritional and probably the therapeutic properties of wines. This is a first evidence-based study where role of recombinant P. acidilactici BD16 (fcs (+)/ech (+)) in the wine secondary fermentation has been elucidated.

Evaluation of the QuEChERS method for the extraction of pharmaceuticals and personal care products from drinking-water treatment sludge with determination by UPLC-ESI-MS/MS.

PubMed

Cerqueira, Maristela B R; Guilherme, Juliana R; Caldas, Sergiane S; Martins, Manoel L; Zanella, Renato; Primel, Ednei G

2014-07-01

A modified version of the QuEChERS method has been evaluated for the determination of 21 pharmaceuticals and 6 personal care products (PPCPs) in drinking-water sludge samples by employing ultra high liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The performance of the method was evaluated through linearity, recovery, precision (intra-day), method detection and quantification limits (MDL and MQL) and matrix effect. The calibration curves prepared in acetonitrile and in the matrix extract showed a correlation coefficient ranging from 0.98 to 0.99. MQLs values were on the ng g(-1) order of magnitude for most compounds. Recoveries between 50% and 93% were reached with RSDs lower than 10% for most compounds. Matrix effect was almost absent with values lower than 16% for 93% of the compounds. By coupling a quick and simple extraction called QuEChERS with the UPLC-MS/MS analysis, a method that is both selective and sensitive was obtained. This methodology was successfully applied to real samples and caffeine and benzophenone-3 were detected in ng g(-1) levels. Copyright © 2014 Elsevier Ltd. All rights reserved.

Golgi- and Trans-Golgi Network-Mediated Vesicle Trafficking Is Required for Wax Secretion from Epidermal Cells1[W][OPEN

PubMed Central

McFarlane, Heather E.; Watanabe, Yoichiro; Yang, Weili; Huang, Yan; Ohlrogge, John; Samuels, A. Lacey

2014-01-01

Lipid secretion from epidermal cells to the plant surface is essential to create the protective plant cuticle. Cuticular waxes are unusual secretory products, consisting of a variety of highly hydrophobic compounds including saturated very-long-chain alkanes, ketones, and alcohols. These compounds are synthesized in the endoplasmic reticulum (ER) but must be trafficked to the plasma membrane for export by ATP-binding cassette transporters. To test the hypothesis that wax components are trafficked via the endomembrane system and packaged in Golgi-derived secretory vesicles, Arabidopsis (Arabidopsis thaliana) stem wax secretion was assayed in a series of vesicle-trafficking mutants, including gnom like1-1 (gnl1-1), transport particle protein subunit120-4, and echidna (ech). Wax secretion was dependent upon GNL1 and ECH. Independent of secretion phenotypes, mutants with altered ER morphology also had decreased wax biosynthesis phenotypes, implying that the biosynthetic capacity of the ER is closely related to its structure. These results provide genetic evidence that wax export requires GNL1- and ECH-dependent endomembrane vesicle trafficking to deliver cargo to plasma membrane-localized ATP-binding cassette transporters. PMID:24468625

Matrix Effect Evaluation and Method Validation of Azoxystrobin and Difenoconazole Residues in Red Flesh Dragon Fruit (Hylocereus polyrhizus) Matrices Using QuEChERS Sample Preparation Methods Followed by LC-MS/MS Determination.

PubMed

Noegrohati, Sri; Hernadi, Elan; Asviastuti, Syanti

2018-06-01

Production of red flesh dragon fruit (Hylocereus polyrhizus) was hampered by Colletotrichum sp. Pre-harvest application of azoxystrobin and difenoconazole mixture is recommended, therefore, a selective and sensitive multi residues analytical method is required in monitoring and evaluating the commodity's safety. LC-MS/MS is a well-established analytical technique for qualitative and quantitative determination in complex matrices. However, this method is hurdled by co-eluted coextractives interferences. This work evaluated the pH effect of acetate buffered and citrate buffered QuEChERS sample preparation in their effectiveness of matrix effect reduction. Citrate buffered QuEChERS proved to produce clean final extract with relative matrix effect 0.4%-0.7%. Method validation of the selected sample preparation followed by LC-MS/MS for whole dragon fruit, flesh and peel matrices fortified at 0.005, 0.01, 0.1 and 1 g/g showed recoveries 75%-119%, intermediate repeatability 2%-14%. The expanded uncertainties were 7%-48%. Based on the international acceptance criteria, this method is valid.

Air-assisted liquid-liquid microextraction integrated with QuEChERS for determining endocrine-disrupting compounds in fish by high-performance liquid chromatography-tandem mass spectrometry.

PubMed

Luo, Zhoufei; Lu, Jing; Li, Haipu; Tu, Yi; Wan, Yuehao; Yang, Zhaoguang

2018-09-15

A new, sensitive, and rapid method based on the Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) approach and air-assisted liquid-liquid microextraction (AALLME) technology was developed for the determination of 20 endocrine-disrupting compounds (EDCs) in fish by high-performance liquid chromatography-tandem mass spectrometry. The method first integrates AALLME into QuEChERS to achieve clean-up and enrichment of the EDCs in one step. A self-made glass tube was enfolded with plasticine to withstand the high centrifugal force. The established method was developed by optimization of the parameters. High linearities (R 2  > 0.9924) and recoveries (78.2-118.6%) at three spiked levels (5, 10, and 20 ng g -1 ), and low relative standard deviation values (1.1-14.5%) and limits of detection (0.03-0.80 ng g -1 ) were obtained. The method comparison shows that the proposed method is superior as it involves less organic solvent usage, simple operation and high efficiency. This method was successfully applied to different fishes for analyzing EDCs. Copyright © 2018 Elsevier Ltd. All rights reserved.

Early College STEM-focused High Schools: A Natural and Overlooked Recruitment Pool for the Geosciences

NASA Astrophysics Data System (ADS)

Freeman, R.; Bathon, J.; Fryar, A. E.; Lyon, E.; McGlue, M. M.

2017-12-01

As national awareness of the importance of STEM education has grown, so too has the number of high schools that specifically emphasize STEM education. Students at these schools outperform their peers and these institutions send students into the college STEM pipeline at twice the rate of the average high school or more. Another trend in secondary education is the "early college high school" (ECHS) model, which encourages students to prepare for and attend college while in high school. These high schools, particularly ECHS's that focus on STEM, represent a natural pool for recruitment into the geosciences, yet most efforts at linking high school STEM education to future careers focus on health sciences or engineering. Through the NSF GEOPATHS-IMPACT program, the University of Kentucky (UK) Department of Earth and Environmental Science and the STEAM Academy, a STEM-focused ECHS located in Lexington, KY, have partnered to expose students to geoscience content. This public ECHS admits students using a lottery system to ensure that the demographics of the high school match those of the surrounding community. The perennial problem for recruiting students into geosciences is the lack of awareness of it as a potential career, due to lack of exposure to the subject in high school. Although the STEAM Academy does not offer an explicitly-named geoscience course, students begin their first semester in 9th grade Integrated Science. This course aligns to the Next Generation Science Standards (NGSS), which include a variety of geoscience content. We are working with the teachers to build a project-based learning curriculum to include explicit mention and awareness of careers in geosciences. The second phase of our project involves taking advantage of the school's existing internship program, in which students develop professional skills and career awareness by spending either one day/week or one hour/day off campus. We hosted our second round of interns this year. Eventually we plan to enroll interested students in introductory earth science courses in our department or at a nearby community college. We hope to build a model for establishing a pipeline from an ECHS STEM high school to a geoscience department that can be implemented by other universities. Here we present the highlights and challenges of this first year of our program.

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 6 2011-10-01 2011-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 6 2012-10-01 2012-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 6 2014-10-01 2014-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

49 CFR 570.7 - Steering systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Steering systems. 570.7 Section 570.7... Pounds or Less § 570.7 Steering systems. (a) System play. Lash or free play in the steering system shall... in the steering system. Table 1—Steering System Free Play Values Steering wheel diameter (inches...

49 CFR 570.60 - Steering system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 6 2014-10-01 2014-10-01 false Steering system. 570.60 Section 570.60... 10,000 Pounds § 570.60 Steering system. (a) System play. Lash or free play in the steering system... excessive lash or free play in the steering system. Table 2. Steering Wheel Free Play Values Steering wheel...

49 CFR 570.60 - Steering system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 6 2012-10-01 2012-10-01 false Steering system. 570.60 Section 570.60... 10,000 Pounds § 570.60 Steering system. (a) System play. Lash or free play in the steering system... excessive lash or free play in the steering system. Table 2. Steering Wheel Free Play Values Steering wheel...

49 CFR 570.60 - Steering system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 6 2011-10-01 2011-10-01 false Steering system. 570.60 Section 570.60... 10,000 Pounds § 570.60 Steering system. (a) System play. Lash or free play in the steering system... excessive lash or free play in the steering system. Table 2. Steering Wheel Free Play Values Steering wheel...

49 CFR 570.60 - Steering system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Steering system. 570.60 Section 570.60... 10,000 Pounds § 570.60 Steering system. (a) System play. Lash or free play in the steering system... excessive lash or free play in the steering system. Table 2. Steering Wheel Free Play Values Steering wheel...

Focusing and steering through absorbing and aberrating layers: application to ultrasonic propagation through the skull.

PubMed

Tanter, M; Thomas, J L; Fink, M

1998-05-01

The time-reversal process is applied to focus pulsed ultrasonic waves through the human skull bone. The aim here is to treat brain tumors, which are difficult to reach with classical surgery means. Such a surgical application requires precise control of the size and location of the therapeutic focal beam. The severe ultrasonic attenuation in the skull reduces the efficiency of the time reversal process. Nevertheless, an improvement of the time reversal process in absorbing media has been investigated and applied to the focusing through the skull [J.-L. Thomas and M. Fink, IEEE Trans. Ultrason. Ferroelectr. Freq. Control 43, 1122-1129 (1996)]. Here an extension of this technique is presented in order to focus on a set of points surrounding an initial artificial source implanted in the tissue volume to treat. From the knowledge of the Green's function matched to this initial source location a new Green's function matched to various points of interest is deduced in order to treat the whole volume. In a homogeneous medium, conventional steering consists of tilting the wave front focused on the acoustical source. In a heterogeneous medium, this process is only valid for small angles or when aberrations are located in a layer close to the array. It is shown here how to extend this method to aberrating and absorbing layers, like the skull bone, located at any distance from the array of transducers.

Wind Plant Power Optimization and Control under Uncertainty

NASA Astrophysics Data System (ADS)

Jha, Pankaj; Ulker, Demet; Hutchings, Kyle; Oxley, Gregory

2017-11-01

The development of optimized cooperative wind plant control involves the coordinated operation of individual turbines co-located within a wind plant to improve the overall power production. This is typically achieved by manipulating the trajectory and intensity of wake interactions between nearby turbines, thereby reducing wake losses. However, there are various types of uncertainties involved, such as turbulent inflow and microscale and turbine model input parameters. In a recent NREL-Envision collaboration, a controller that performs wake steering was designed and implemented for the Longyuan Rudong offshore wind plant in Jiangsu, China. The Rudong site contains 25 Envision EN136-4 MW turbines, of which a subset was selected for the field test campaign consisting of the front two rows for the northeasterly wind direction. In the first row, a turbine was selected as the reference turbine, providing comparison power data, while another was selected as the controlled turbine. This controlled turbine wakes three different turbines in the second row depending on the wind direction. A yaw misalignment strategy was designed using Envision's GWCFD, a multi-fidelity plant-scale CFD tool based on SOWFA with a generalized actuator disc (GAD) turbine model, which, in turn, was used to tune NREL's FLORIS model used for wake steering and yaw control optimization. The presentation will account for some associated uncertainties, such as those in atmospheric turbulence and wake profile.

Experimental verification of multidimensional quantum steering

NASA Astrophysics Data System (ADS)

Li, Che-Ming; Lo, Hsin-Pin; Chen, Liang-Yu; Yabushita, Atsushi

2018-03-01

Quantum steering enables one party to communicate with another remote party even if the sender is untrusted. Such characteristics of quantum systems not only provide direct applications to quantum information science, but are also conceptually important for distinguishing between quantum and classical resources. While concrete illustrations of steering have been shown in several experiments, quantum steering has not been certified for higher dimensional systems. Here, we introduce a simple method to experimentally certify two different kinds of quantum steering: Einstein-Podolsky-Rosen (EPR) steering and single-system (SS) steering (i.e., temporal steering), for dimensionality (d) up to d = 16. The former reveals the steerability among bipartite systems, whereas the latter manifests itself in single quantum objects. We use multidimensional steering witnesses to verify EPR steering of polarization-entangled pairs and SS steering of single photons. The ratios between the measured witnesses and the maximum values achieved by classical mimicries are observed to increase with d for both EPR and SS steering. The designed scenario offers a new method to study further the genuine multipartite steering of large dimensionality and potential uses in quantum information processing.

A Hierarchical Model Predictive Tracking Control for Independent Four-Wheel Driving/Steering Vehicles with Coaxial Steering Mechanism

NASA Astrophysics Data System (ADS)

Itoh, Masato; Hagimori, Yuki; Nonaka, Kenichiro; Sekiguchi, Kazuma

2016-09-01

In this study, we apply a hierarchical model predictive control to omni-directional mobile vehicle, and improve the tracking performance. We deal with an independent four-wheel driving/steering vehicle (IFWDS) equipped with four coaxial steering mechanisms (CSM). The coaxial steering mechanism is a special one composed of two steering joints on the same axis. In our previous study with respect to IFWDS with ideal steering, we proposed a model predictive tracking control. However, this method did not consider constraints of the coaxial steering mechanism which causes delay of steering. We also proposed a model predictive steering control considering constraints of this mechanism. In this study, we propose a hierarchical system combining above two control methods for IFWDS. An upper controller, which deals with vehicle kinematics, runs a model predictive tracking control, and a lower controller, which considers constraints of coaxial steering mechanism, runs a model predictive steering control which tracks the predicted steering angle optimized an upper controller. We verify the superiority of this method by comparing this method with the previous method.

Imagerie combinée géoélectrique radar géologique des cavités souterraines de la ville de Zaouit Ech Cheikh (Maroc)

NASA Astrophysics Data System (ADS)

El Khammari, Kamal; Najine, Abdessamad; Jaffal, Mohammed; Aïfa, Tahar; Himi, Mahjoub; Vásquez, Diego; Casas, Albert; Andrieux, Pierre

2007-06-01

The basement of the Zaouit Ech Cheikh city shelters a dense network of underground cavities. These sub-surface voids make many buildings or infrastructures unstable or cause them to collapse. To test the efficiency of geophysical methods in detecting cavities, 2D electrical tomography and ground-penetrating radar (GPR) studies were carried out along the main streets of the city. The obtained results reveal the existence of a large number of underground cavities throughout the investigated area. They also show the interest of such combined geophysical methods as tools for mapping underground holes in an urban area.

46 CFR 58.25-80 - Automatic pilots and ancillary steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... AND AUXILIARY MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-80 Automatic pilots and ancillary steering gear. (a) Automatic pilots and ancillary steering gear, and steering-gear control systems, must be arranged to allow immediate resumption of manual operation of the steering-gear control system required in...

46 CFR 58.25-80 - Automatic pilots and ancillary steering gear.

Code of Federal Regulations, 2011 CFR

2011-10-01

... AND AUXILIARY MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-80 Automatic pilots and ancillary steering gear. (a) Automatic pilots and ancillary steering gear, and steering-gear control systems, must be arranged to allow immediate resumption of manual operation of the steering-gear control system required in...

Technologies for Elastic Optical Networking Systems in Spatial, Temporal and Spectral Domains

NASA Astrophysics Data System (ADS)

Qin, Chuan

As the demand for more data capacity keeps increasing, the need for the more efficient use of the data channel becomes more imperative. The fixed wavelength grid which has been in use for more than ten years in conventional wavelength division multiplexing (WDM) is a bottleneck that prevents the capacity from upgrading towards 400 Gb/s and above. A new elastic optical networking scheme where both transceivers and interconnects become flexible break the boundary of wavelength grids and allow a more efficient use of the limited optical bands for communication. This dissertation focuses on a few enabling technologies for elastic optical networking systems. Optical arbitrary waveform generation (OAWG) uses Fourier synthesis and generates user-defined broad-band scalable optical waveforms with high-fidelity through line-by-line full field control of a coherent optical frequency comb. OAWG finds its niche in elastic optical networking since it provides no grids, and scales to user-defined bandwidth. When elastic optical networking builds various connections to use an arbitrary number of subcarriers depending on the users' bandwidth needs, the flexibility also creates non-contiguous spectral fragmentation, much like a computer hard disk generating fragments. Spectral defragmentation aims to re-optimize and re-assign the optical spectrum to achieve more efficient use of the spectrum. One of the technologies is "hop tuning" defragmentation method with a fast auto-tracking local oscillator (LO). In the demonstrated defragmentation experiment, I used a field-programmable gate array (FPGA) to monitor the wavelength change in the signal laser and tune the front and rear current that controls the wavelength of the local oscillator laser. However, the control of the front and rear current needs a complete and accurate calibration of the LO laser and may not apply to a larger number of coherent communication links. A single-tone optical frequency shifter can shift the LO laser wavelength to track the signal wavelength, thus providing a technique for authentically automatic wavelength tracking. I also explored different materials and crystal orientations to reduce the radio-frequency (RF) power consumption required to shift the wavelengths. Based on the elastic optical networking in the temporal, spectral and spatial domains, an additional degree of freedom has been investigated recently to increase the data capacity. The exploration to use the spatial domain to carry more data is termed as spatial division multiplexing (SDM). One such SDM method is orbital angular momentum(OAM), which is a group of orthogonal light beams carrying orbital angular momentum exhibiting an azimuthal phase variation. The utilization of OAM states has the potential to significantly increase the spectral efficiency and channel capacity. The thesis also includes the demonstration to establish a connection by exploiting the elasticity steering in spatial, temporal and spectral domains. Beam steering based on optical phased array (OPA) is also a potential candidate of SDM to carry information when a different linear phase will distribute light to different spatial locations. The states are intrinsically orthogonal to one another. Using 4x4 3-D waveguides written by ultrafast laser inscription (ULI), we demonstrated 2-D optical phased array (OPA) beam steering that shows steering in both vertical and horizontal directions. Enabling technologies provide future pathways for elastic optical networking and will fundamentally impact optical communication systems in many ways.

46 CFR 182.610 - Main steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Main steering gear. 182.610 Section 182.610 Shipping...) MACHINERY INSTALLATION Steering Systems § 182.610 Main steering gear. (a) A vessel must be provided with a main steering gear that is: (1) Of adequate strength and capable of steering the vessel at all service...

46 CFR 108.641 - Instructions for changing steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Instructions for changing steering gear. 108.641 Section... steering gear. Instructions stating, in order, the different steps to be taken for changing to emergency and secondary steering gear must be posted in the steering gear room and at each secondary steering...

Steering and Suspension Systems. Auto Mechanics Curriculum Guide. Module 5. Instructor's Guide.

ERIC Educational Resources Information Center

Rains, Larry

This module is the fifth of nine modules in the competency-based Missouri Auto Mechanics Curriculum Guide. Seventeen units cover: steering system design; diagnosing steering systems problems; inspecting and replacing steering linkage components; manual and power steering gear service; manual and power rack and pinion steering gear service; power…

46 CFR 131.845 - Instructions for shift of steering gear.

Code of Federal Regulations, 2013 CFR

2013-10-01

... alternative steering stations must be on water-resistant material and posted at each steering station and in... gear or steering stations. (d) Each clutch, gear, wheel, lever, valve, or switch used during any shift of steering gear or steering stations must be numbered or lettered on a metal plate or painted so...

Enhancement of thermal blooming effect on free space propagation of high power CW laser beam

NASA Astrophysics Data System (ADS)

Kashef, Tamer M.; Mokhtar, Ayman M.; Ghoniemy, Samy A.

2018-02-01

In this paper, we present an enhanced model to predict the effect of thermal blooming and atmospheric turbulence, on high energy laser beams free space propagation. We introduce an implementation technique for the proposed mathematical models describing the effect of thermal blooming and atmospheric turbulence including wind blowing, and how it effect high power laser beam power, far field pattern, phase change effect and beam quality . An investigated model of adaptive optics was introduced to study how to improve the wave front and phase distortion caused by thermal blooming and atmospheric turbulence, the adaptive optics model with Actuator influence spacing 3 cm the that shows observed improvement in the Strehl ratio and in wave front and phase of the beam. These models was implemented using cooperative agents relying on GLAD software package. Without taking in consideration the effect of thermal blooming It was deduced that the beam at the source takes the Gaussian shape with uniform intensity distribution, we found that the beam converge on the required distance 4 km using converging optics, comparing to the laser beam under the effect of thermal blooming the far field pattern shows characteristic secondary blip and "sugar scoop" effect which is characteristic of thermal blooming. It was found that the thermal blooming causes the beam to steer many centimeters and to diverge beyond about 1.8 km than come to a focus at 4 km where the beam assumed to be focused on the required target. We assume that this target is moving at v = (4,-4) m/sec at distance 4 km and the wind is moving at v = (-10,-10) m/sec, it was found that the effect will be strongest when wind and target movement are at the same velocity. GLAD software is used to calculate the attenuation effects of the atmosphere as well as the phase perturbations due to temperature change in the air and effects caused as the beam crosses through the air due to wind and beam steering.

BEAMLINE-CONTROLLED STEERING OF SOURCE-POINT ANGLE AT THE ADVANCED PHOTON SOURCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Emery, L.; Fystro, G.; Shang, H.

An EPICS-based steering software system has been implemented for beamline personnel to directly steer the angle of the synchrotron radiation sources at the Advanced Photon Source. A script running on a workstation monitors "start steering" beamline EPICS records, and effects a steering given by the value of the "angle request" EPICS record. The new system makes the steering process much faster than before, although the older steering protocols can still be used. The robustness features of the original steering remain. Feedback messages are provided to the beamlines and the accelerator operators. Underpinning this new steering protocol is the recent refinementmore » of the global orbit feedback process whereby feedforward of dipole corrector set points and orbit set points are used to create a local steering bump in a rapid and seamless way.« less

Update on the DIII-D ECH system: experiments, gyrotrons, advanced diagnostics, and controls

NASA Astrophysics Data System (ADS)

Lohr, John; Brambila, Rigoberto; Cengher, Mirela; Gorelov, Yuri; Grosnickle, William; Moeller, Charles; Ponce, Dan; Torrezan, Antonio; Ives, Lawrence; Reed, Michael; Blank, Monica; Felch, Kevin; Parisuaña, Claudia; LeViness, Alexandra

2017-08-01

The ECH system on DIII-D is continuing to be upgraded, while simultaneously being operated nearly daily for plasma experiments. The latest major hardware addition is a new 117.5 GHz gyrotron, which generated 1.7 MW for short pulses during factory testing. A new gyrotron control system based on Field Programmable Gate Array (FPGA) technology with very high speed system data acquisition has significantly increased the flexibility and reliability of individual gyrotron operation. We have improved the performance of the fast mirror scanning, both by increasing the scan speeds and by adding new algorithms for controlling the aiming using commands generated by the Plasma Control System (PCS). The system is used for transport studies, ELM control, current profile control, non-inductive current generation, suppression of MHD modes, startup assist, plasma density control, and other applications. A program of protective measures, which has been in place for more than two years, has eliminated damage to hardware and diagnostics caused by overdense operation. Other activities not directly related to fusion research have used the ECH system to test components, study methods for improving production of semiconductor junctions and materials, and test the feasibility of using ground based microwave systems to power satellites into orbit.

Determination of coumarin in seasonal bakery products using QuEChERS and GC-MS.

PubMed

Vetter, F; Müller, C; Stöckelhuber, M; Bracher, F

2017-06-01

Cinnamon is a traditional herbal drug, but more importantly, it is used as a flavor compound in the production of foodstuff. Due to the content of significant concentrations of coumarin in Cassia cinnamon, effective control of the coumarin content in seasonal bakery products like ginger bread and cinnamon biscuits is urgently needed. Here we present a novel, fast and fully validated protocol for the determination of coumarin in marketed bakery products using the QuEChERS sample preparation technique in combination with GC-MS analysis. Ten grams of homogenized sample was mixed with 20 mL acetonitrile/water (1:1) and 5 g magnesium sulfate/sodium chloride mixture (4:1). The organic phase was cleaned by dSPE with 25 mg magnesium sulfate/PSA (5:1). The LOD was 0.15 μg/mL and the LOQ 0.50 μg/mL. We detected a mean coumarin content of 19.5 μg/kg in 9 out of 14 seasonal food products (ranging from 1.45 to 39.4 mg/kg). No coumarin was detected in five cinnamon containing products. With this investigation we demonstrate that the QuEChERS sample preparation, previously applied mainly to the analysis of pesticides in vegetables, is also suitable for other complex matrices.

Simultaneous Analysis of Ursolic Acid and Oleanolic Acid in Guava Leaves Using QuEChERS-Based Extraction Followed by High-Performance Liquid Chromatography

PubMed Central

Xu, Chang; Liao, Yiyi; Fang, Chunyan; Zhang, Yingxia

2017-01-01

In this paper, a novel method of QuEChERS-based extraction coupled with high-performance liquid chromatography has been developed for the simultaneous determination of ursolic acid (UA) and oleanolic acid (OA) in guava leaves. The QuEChERS-based extraction parameters, including the amount of added salt, vortex-assisted extraction time, and absorbent amount, and the chromatographic conditions were investigated for the analysis of UA and OA in guava leaves. Under the optimized conditions, the method showed good linearity over a range of 1–320 μg mL−1, with correlation coefficients above 0.999. The limits of detection of UA and OA were 0.18 and 0.36 μg mL−1, respectively. The intraday and interday precision were below 1.95 and 2.55%, respectively. The accuracies of the UA and OA determinations ranged from 97.4 to 111.4%. The contents of UA and OA in the guava leaf samples were 2.50 and 0.73 mg g−1, respectively. These results demonstrate that the developed method is applicable to the simultaneous determination of UA and OA in guava leaves. PMID:28781908

The study of Equatorial coronal hole during maximum phase of Solar Cycle 21, 22, 23 and 24

NASA Astrophysics Data System (ADS)

Karna, Mahendra; Karna, Nishu

2017-08-01

The 11-year Solar Cycle (SC) is characterized by the periodic change in the solar activity like sunspot numbers, coronal holes, active regions, eruptions such as flares and coronal mass ejections. We study the relationship between equatorial coronal holes (ECH) and the active regions (AR) as coronal whole positions and sizes change with the solar cycle. We made a detailed study of equatorial coronal hole for four solar maximum: Solar Cycle 21 (1979,1980,1981 and 1982), Solar Cycle 22 (1989, 1990, 1991 and 1992), Solar Cycle 23 (1999, 2000, 2001 and 2002) and Solar Cycle 24 (2012, 2013, 2014 and 2015). We used publically available NOAA solar coronal hole data for cycle 21 and 22. We measured the ECH region using the EIT and AIA synoptic map for cycle 23 and 24. We noted that in two complete 22-year cycle of solar activity, the equatorial coronal hole numbers in SC 22 is greater than SC 21 and similarly, SC 24 equatorial coronal hole numbers are greater than SC 23. Moreover, we also compared the position of AR and ECH during SC 23 and 24. We used daily Solar Region Summary (SRS) data from SWPC/NOAA website. Our goal is to examine the correlation between equatorial holes, active regions, and flares.

Promoted decomposition of NOx in automotive diesel-like exhausts by electro-catalytic honeycombs.

PubMed

Huang, Ta-Jen; Chiang, De-Yi; Shih, Chi; Lee, Cheng-Chin; Mao, Chih-Wei; Wang, Bo-Chung

2015-03-17

NO and NO2 (collectively called NOx) are major air pollutants in automotive emissions. More effective and easier treatments of NOx than those achieved by the present methods can offer better protection of human health and higher fuel efficiency that can reduce greenhouse gas emissions. However, currently commercialized technologies for automotive NOx emission control cannot effectively treat diesel-like exhausts with high NOx concentrations. Thus, exhaust gas recirculation (EGR) has been used extensively, which reduces fuel efficiency and increases particulate emission considerably. Our results show that the electro-catalytic honeycomb (ECH) promotes the decomposition of NOx to nitrogen and oxygen, without consuming reagents or other resources. NOx can be converted to nitrogen and oxygen almost completely. The ECHs are shown to effectively remove NOx from gasoline-fueled diesel-like exhausts. A very high NO concentration is preferred in the engine exhaust, especially during engine cold-start. Promoted NOx decomposition (PND) technology for real-world automotive applications is established in this study by using the ECH. With PND, EGR is no longer needed. Diesel-like engines can therefore achieve superior fuel efficiency, and all major automotive pollutants can be easily treated due to high concentration of oxygen in the diesel-like exhausts, leading to zero pollution.

QuEChERS-based purification method coupled to ultrahigh performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) to determine six quaternary ammonium compounds (QACs) in dairy products.

PubMed

Xian, Yanping; Dong, Hao; Wu, Yuluan; Guo, Xindong; Hou, Xiangchang; Wang, Bin

2016-12-01

QuEChERS-based purification coupled with UPLC-MS/MS method, was developed for six quaternary ammonium compounds (QACs) determination in dairy products. Powder samples were firstly dispersed by water. Protein in liquid milk was precipitated and sample solution was extracted by acetonitrile. QuEChERS-based purification was used to purify the solution. QACs were finally separated by HILIC column and detected in MRM mode of MS/MS under ESI(+). The stable isotope benzyl-2,3,4,5,6-d5-dimethyltetradecylammonium bromide (C14-BAC-d5) was used as an internal standard. This method was validated in terms of linearity, sensitivity, precision, accuracy. Linear relations were favorable for QACs over the selected concentration ranges of 0.2-50μg/L, with correlation coefficients greater than 0.999. The limits of detection (LODs) were in the range of 0.4-14.5μg/kg. Recoveries were between 91.2% and 115% with RSDs of 2.8-7.5% for intra-day precision and 3.7-6.7% for inter-day precision. This validated method was successfully applied to determine the QACs concentrations in dairy products. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ionosphere-Magnetosphere Energy Interplay in the Regions of Diffuse Aurora

NASA Technical Reports Server (NTRS)

Khazanov, G. V.; Glocer, A.; Sibeck, D. G.; Tripathi, A. K.; Detweiler, L.G.; Avanov, L. A.; Singhal, R. P.

2016-01-01

Both electron cyclotron harmonic (ECH) waves and whistler mode chorus waves resonate with electrons of the Earths plasma sheet in the energy range from tens of eV to several keV and produce the electron diffuse aurora at ionospheric altitudes. Interaction of these superthermal electrons with the neutral atmosphere leads to the production of secondary electrons (E500600 eV) and, as a result, leads to the activation of lower energy superthermal electron spectra that can escape back to the magnetosphere and contribute to the thermal electron energy deposition processes in the magnetospheric plasma. The ECH and whistler mode chorus waves, however, can also interact with the secondary electrons that are coming from both of the magnetically conjugated ionospheres after they have been produced by initially precipitated high-energy electrons that came from the plasma sheet. After their degradation and subsequent reflection in magnetically conjugate atmospheric regions, both the secondary electrons and the precipitating electrons with high (E600 eV) initial energies will travel back through the loss cone, become trapped in the magnetosphere, and redistribute the energy content of the magnetosphere-ionosphere system. Thus, scattering of the secondary electrons by ECH and whistler mode chorus waves leads to an increase of the fraction of superthermal electron energy deposited into the core magnetospheric plasma.

Cost of Einstein-Podolsky-Rosen steering in the context of extremal boxes

NASA Astrophysics Data System (ADS)

Das, Debarshi; Datta, Shounak; Jebaratnam, C.; Majumdar, A. S.

2018-02-01

Einstein-Podolsky-Rosen steering is a form of quantum nonlocality, which is weaker than Bell nonlocality, but stronger than entanglement. Here we present a method to check Einstein-Podolsky-Rosen steering in the scenario where the steering party performs two black-box measurements and the trusted party performs projective qubit measurements corresponding to two arbitrary mutually unbiased bases. This method is based on decomposing the measurement correlations in terms of extremal boxes of the steering scenario. In this context, we propose a measure of steerability called steering cost. We show that our steering cost is a convex steering monotone. We illustrate our method to check steerability with two families of measurement correlations and find out their steering cost.

Effects of preshipping management on measures of stress and performance of beef steers during feedlot receiving.

PubMed

Arthington, J D; Qiu, X; Cooke, R F; Vendramini, J M B; Araujo, D B; Chase, C C; Coleman, S W

2008-08-01

Over 2 yr, a total of 96 steers (approximately 7 mo of age) were allocated to 1 of 4 weaning management strategies: 1) control: weaned on the day of shipping; 2) creep-fed: allowed free-choice access to concentrate before weaning and shipping; 3) preweaned: weaned and provided supplemental concentrate on pasture before shipping; and 4) early-weaned: weaned at 70 to 90 d of age and kept on pasture. On the day of shipping, steers were loaded together onto a commercial livestock trailer and transported 1,600 km over 24 h before being received into the feedlot. At the feedlot, steers were penned by treatment (4 pens/treatment) and provided access to free-choice hay and concentrate in separate feeding spaces. Samples of blood were collected on d 0, 1, 4, 8, 15, 22, and 29 relative to shipping. Steer performance was assessed over the receiving period, including DMI of hay and concentrate, ADG, and G:F. Predetermined contrasts included control vs. early-weaned, creep-fed vs. preweaned, and control vs. creep-fed and preweaned. Overall ADG was greater (P < 0.01) for early-weaned vs. control steers (1.39 vs. 0.88 kg). In wk 1, early-weaned steers consumed more concentrate and less hay compared with control steers (P < 0.03), and preweaned steers consumed more concentrate (P < 0.01) but a similar amount of hay (P = 0.75) compared with creep-fed steers. Average DMI was greater for preweaned compared with creep-fed steers (2.84 vs. 2.50% of BW; P = 0.01) and tended to be greater for early-weaned compared with control steers (2.76 vs. 2.50% of BW; P = 0.06). Feed efficiency of early-weaned steers was greater than that of control steers (G:F = 0.17 vs. 0.12; P < 0.01) but similar for preweaned compared with creep-fed steers (P = 0.72). Plasma ceruloplasmin concentrations were less (P < 0.05) in control vs. early-weaned steers on d 0, but increased sharply after shipping and were greater in control vs. early-weaned steers on d 15 and 22 (P < 0.05). Creep-fed steers also experienced greater (P < 0.05) plasma ceruloplasmin concentrations than preweaned steers on d 29. These data suggest that early-weaned steers have improved performance in the feedlot compared with steers weaned directly before transport and feedlot entry. Differences in preshipping management appear to significantly affect measures of the acute phase protein response in steers.

Investigation of ion and electron heat transport of high- T e ECH heated discharges in the large helical device

DOE PAGES

Pablant, N. A.; Satake, S.; Yokoyama, M.; ...

2016-01-28

An analysis of the radial electric field and heat transport, both for ions and electrons, is presented for a high-more » $${{T}_{\\text{e}}}$$ electron cyclotron heated (ECH) discharge on the large helical device (LHD). Transport analysis is done using the task3d transport suite utilizing experimentally measured profiles for both ions and electrons. Ion temperature and perpendicular flow profiles are measured using the recently installed x-ray imaging crystal spectrometer diagnostic (XICS), while electron temperature and density profiles are measured using Thomson scattering. The analysis also includes calculated ECH power deposition profiles as determined through the travis ray-tracing code. This is the first time on LHD that this type of integrated transport analysis with measured ion temperature profiles has been performed without NBI, allowing the heat transport properties of plasmas with only ECH heating to be more clearly examined. For this study, a plasma discharge is chosen which develops a high central electron temperature ($${{T}_{\\text{eo}}}=9$$ keV) at moderately low densities ($${{n}_{\\text{eo}}}=1.5\\times {{10}^{19}}$$ m-3). The experimentally determined transport properties from task3d are compared to neoclassical predictions as calculated by the gsrake and fortec-3d codes. The predicted electron fluxes are seen to be an order of magnitude less than the measured fluxes, indicating that electron transport is largely anomalous, while the neoclassical and measured ion heat fluxes are of the same magnitude. Neoclassical predictions of a strong positive ambipolar electric field ($${{E}_{\\text{r}}}$$ ) in the plasma core are validated through comparisons to perpendicular flow measurements from the XICS diagnostic. Furthermore, this provides confidence that the predictions are producing physically meaningful results for the particle fluxes and radial electric field, which are a key component in correctly predicting plasma confinement.« less

Cross-shore velocity shear, eddies and heterogeneity in water column properties over fringing coral reefs: West Maui, Hawaii

USGS Publications Warehouse

Storlazzi, C.D.; McManus, M.A.; Logan, J.B.; McLaughlin, B.E.

2006-01-01

A multi-day hydrographic survey cruise was conducted to acquire spatially extensive, but temporally limited, high-resolution, three-dimensional measurements of currents, temperature, salinity and turbidity off West Maui in the summer of 2003 to better understand coastal dynamics along a complex island shoreline with coral reefs. These data complement long-term, high-resolution tide, wave, current, temperature, salinity and turbidity measurements made at a number of fixed locations in the study area starting in 2001. Analyses of these hydrographic data, in conjunction with numerous field observations, evoke the following conceptual model of water and turbidity flux along West Maui. Wave- and wind-driven flows appear to be the primary control on flow over shallower portions of the reefs while tidal and subtidal currents dominate flow over the outer portions of the reefs and insular shelf. When the direction of these flows counter one another, which is quite common, they cause a zone of cross-shore horizontal shear and often form a front, with turbid, lower-salinity water inshore of the front and clear, higher-salinity water offshore of the front. It is not clear whether these zones of high shear and fronts are the cause or the result of the location of the fore reef, but they appear to be correlated alongshore over relatively large horizontal distances (orders of kilometers). When two flows converge or when a single flow is bathymetrically steered, eddies can be generated that, in the absence of large ocean surface waves, tend to accumulate material. Areas of higher turbidity and lower salinity tend to correlate with regions of poor coral health or the absence of well-developed reefs, suggesting that the oceanographic processes that concentrate and/or transport nutrients, contaminants, low-salinity water or suspended sediment might strongly influence coral reef ecosystem health and sustainability.

Detection of quantum steering in multipartite continuous-variable Greenberger-Horne-Zeilinger-like states

NASA Astrophysics Data System (ADS)

Wang, Meng; Xiang, Yu; He, Qiongyi; Gong, Qihuang

2015-01-01

The multipartite entangled state has drawn broad attention for both foundations of quantum mechanics and applications in quantum information processing. Here, we study the spatially separated N -partite continuous-variable Greenberger-Horne-Zeilinger-like states, which can be produced by a linear optical network with squeezed light and N -1 beamsplitters. We investigate the properties of multipartite Einstein-Podolsky-Rosen steering possessed by those states, and find that the steering of a given quantum mode is allowed when not less than half of the modes within the states take part in the steering group. This is certified by the detection of the correlation between position and momentum quadratures of the steered mode and a combination of quadratures of other modes inside the steering group. The steering is evidenced by the high correlation where the steering group can infer the quadratures of the steered mode to high precision, i.e., below the quantum limit for the position and momentum quadratures of the steered quantum mode. We also examine the influence of inefficiency on the multipartite steering, and derive the threshold of the loss tolerance. Furthermore, we discuss the collective N -partite steering induced by the asymmetric loss on beams, which exists when a given quantum mode can only be steered by all the remaining N -1 modes collaboratively. The present multipartite steering correlation may have potential applications in certain quantum information tasks where the issue of trust is important, such as one-sided device-independent quantum secret sharing.

Monitoring the CMS strip tracker readout system

NASA Astrophysics Data System (ADS)

Mersi, S.; Bainbridge, R.; Baulieu, G.; Bel, S.; Cole, J.; Cripps, N.; Delaere, C.; Drouhin, F.; Fulcher, J.; Giassi, A.; Gross, L.; Hahn, K.; Mirabito, L.; Nikolic, M.; Tkaczyk, S.; Wingham, M.

2008-07-01

The CMS Silicon Strip Tracker at the LHC comprises a sensitive area of approximately 200 m2 and 10 million readout channels. Its data acquisition system is based around a custom analogue front-end chip. Both the control and the readout of the front-end electronics are performed by off-detector VME boards in the counting room, which digitise the raw event data and perform zero-suppression and formatting. The data acquisition system uses the CMS online software framework to configure, control and monitor the hardware components and steer the data acquisition. The first data analysis is performed online within the official CMS reconstruction framework, which provides many services, such as distributed analysis, access to geometry and conditions data, and a Data Quality Monitoring tool based on the online physics reconstruction. The data acquisition monitoring of the Strip Tracker uses both the data acquisition and the reconstruction software frameworks in order to provide real-time feedback to shifters on the operational state of the detector, archiving for later analysis and possibly trigger automatic recovery actions in case of errors. Here we review the proposed architecture of the monitoring system and we describe its software components, which are already in place, the various monitoring streams available, and our experiences of operating and monitoring a large-scale system.

Development of BPM Electronics at the JLAB FEL

NASA Astrophysics Data System (ADS)

Sexton, D.; Evtushenko, P.; Jordan, K.; Yan, J.; Dutton, S.; Moore, W.; Evans, R.; Coleman, J.

2006-11-01

A new version of BPM electronics based on the AD8362 RMS detector, which is a direct RF to DC converter, is under development at the JLAB FEL. Each of these new BPM electronics utilizes an embedded ColdFire Microprocessor for data processing and communication with the EPICS control system via TCP/IP. The ColdFire runs RTEMS, which is an open source real-time operating system. The JLAB FEL is a SRF Energy Recovery LINAC capable of running up to 10 mA CW beam with a 74.85 MHz micropulse frequency. For diagnostic reasons and for machine tune up, the micropulse frequency can be reduced to 1.17 MHz, which corresponds to about 160 μA of beam current. It is required that the BPM system would be functional for all micropulse frequencies. By taking into account the headroom for the beam steering and current variations the dynamic range of the RF front end is required to be about 60 dB. A BPM resolution of at least 100 μm is required, whereas better resolution is very desirable to make it possible for more accurate measurements of the electron beam optics. Some results of the RF front end development are presented as well as the first measurements made with an electron beam.

Development of BPM Electronics at the JLAB FEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sexton, D.; Evtushenko, P.; Jordan, K.

2006-11-20

A new version of BPM electronics based on the AD8362 RMS detector, which is a direct RF to DC converter, is under development at the JLAB FEL. Each of these new BPM electronics utilizes an embedded ColdFire Microprocessor for data processing and communication with the EPICS control system via TCP/IP. The ColdFire runs RTEMS, which is an open source real-time operating system. The JLAB FEL is a SRF Energy Recovery LINAC capable of running up to 10 mA CW beam with a 74.85 MHz micropulse frequency. For diagnostic reasons and for machine tune up, the micropulse frequency can be reducedmore » to 1.17 MHz, which corresponds to about 160 {mu}A of beam current. It is required that the BPM system would be functional for all micropulse frequencies. By taking into account the headroom for the beam steering and current variations the dynamic range of the RF front end is required to be about 60 dB. A BPM resolution of at least 100 {mu}m is required, whereas better resolution is very desirable to make it possible for more accurate measurements of the electron beam optics. Some results of the RF front end development are presented as well as the first measurements made with an electron beam.« less

Development of BPM Electronics at the JLAB FEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel Sexton; Pavel Evtushenko; Kevin Jordan

2006-05-01

A new version of BPM electronics based on the AD8362 RMS detector, which is a direct RF to DC converter, is under development at the JLAB FEL. Each of these new BPM electronics utilizes an embedded ColdFire Microprocessor for data processing and communication with the EPICS control system via TCP/IP. The ColdFire runs RTEMS, which is an open source real-time operating system. The JLAB FEL is a SRF Energy Recovery LINAC capable of running up to 10 mA CW beam with the micropulse up to 74.85 MHz. For diagnostic reasons and for the machine tune up, the micropulse frequency canmore » be reduced to 1.17 MHz, which corresponds to about 160 ?A of beam current. It is required that the BPM system would be functional for all micropulse frequencies. By taking into account the headroom for the beam steering and current variations the dynamic range of the RF front end is required to be about 60 dB. A BPM resolution of at least 100 ?m is required, whereas better resolution is very desirable to make it possible for more accurate measurements of the electron beam optics. Some results of the RF front end development are presented as well as the first measurements made with an electron beam.« less

Ants swimming in pitcher plants: kinematics of aquatic and terrestrial locomotion in Camponotus schmitzi.

PubMed

Bohn, Holger Florian; Thornham, Daniel George; Federle, Walter

2012-06-01

Camponotus schmitzi ants live in symbiosis with the Bornean pitcher plant Nepenthes bicalcarata. Unique among ants, the workers regularly dive and swim in the pitcher's digestive fluid to forage for food. High-speed motion analysis revealed that C. schmitzi ants swim at the surface with all legs submerged, with an alternating tripod pattern. Compared to running, swimming involves lower stepping frequencies and larger phase delays within the legs of each tripod. Swimming ants move front and middle legs faster and keep them more extended during the power stroke than during the return stroke. Thrust estimates calculated from three-dimensional leg kinematics using a blade-element approach confirmed that forward propulsion is mainly achieved by the front and middle legs. The hind legs move much less, suggesting that they mainly serve for steering. Experiments with tethered C. schmitzi ants showed that characteristic swimming movements can be triggered by submersion in water. This reaction was absent in another Camponotus species investigated. Our study demonstrates how insects can use the same locomotory system and similar gait patterns for moving on land and in water. We discuss insect adaptations for aquatic/amphibious lifestyles and the special adaptations of C. schmitzi to living on an insect-trapping pitcher plant.

Dynamics of the Antarctic Circumpolar Current. Evidence for Topographic Effects from Altimeter Data and Numerical Model Output

NASA Technical Reports Server (NTRS)

Gille, Sarah T.

1995-01-01

Geosat altimeter data and numerical model output are used to examine the circulation and dynamics of the Antarctic Circumpolar Current (ACC). The mean sea surface height across the ACC has been reconstructed from height variability measured by the altimeter, without assuming prior knowledge of the geoid. The results indicate locations for the Subantarctic and Polar Fronts which are consistent with in situ observations and indicate that the fronts are substantially steered by bathymetry. Detailed examination of spatial and temporal variability indicates a spatial decorrelation scale of 85 km and a temporal e-folding scale of 34 days. Empirical Orthogonal Function analysis suggests that the scales of motion are relatively short, occuring on 1000 km length-scales rather than basin or global scales. The momentum balance of the ACC has been investigated using output from the high resolution primitive equation model in combination with altimeter data. In the Semtner-Chervin quarter-degree general circulation model topographic form stress is the dominant process balancing the surface wind forcing. In stream coordinates, the dominant effect transporting momentum across the ACC is bibarmonic friction. Potential vorticity is considered on Montgomery streamlines in the model output and along surface streamlines in model and altimeter data. (AN)

Monogamy of Einstein-Podolsky-Rosen Steering in the Background of an Asymptotically Flat Black Hole

NASA Astrophysics Data System (ADS)

Wang, Jieci; Jing, Jiliang; Fan, Heng

2018-03-01

We study the behavior of monogamy deficit and monogamy asymmetry for Einstein-Podolsky-Rosen steering of Gaussian states under the influence of the Hawking effect. We demonstrate that the monogamy of quantum steering shows an extreme scenario in the curved spacetime: the first part of a tripartite system cannot individually steer two other parties, but it can steer the collectivity of the remaining two parties. We also find that the monogamy deficit of Gaussian steering, a quantifier of genuine tripartite steering, are generated due to the influence of the Hawking thermal bath. Our results elucidate the structure of quantum steering in tripartite quantum systems in curved spacetime.

Electrocatalytic Hydrogenation of Phenol over Platinum and Rhodium: Unexpected Temperature Effects Resolved

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Nirala; Song, Yang; Gutiérrez, Oliver Y.

2016-11-04

Both electrocatalytic hydrogenation (ECH) and thermal hydrogenation (TH) of phenol by Pt and Rh show a roll-over in rate with increasing temperature without changing the principal reaction pathways. The negative effect of temperature for aqueous-phase phenol H2 and electrocatalytic hydrogenation on Pt and Rh is deduced to be due to the unexpected buildup of dehydrogenated phenol adsorbates, which block active sites. Rates of ECH and TH increase similarly with increasing hydrogen chemical potential whether induced by applied potential or H2 pressure, both via increasing H coverage, and indirectly by removing site blockers, a very strong effect at high temperature. Thismore » enables unprecedented rates in the TH of phenol at these temperatures.« less

Evaluation of the QuEChERS Method and Gas Chromatography–Mass Spectrometry for the Analysis Pesticide Residues in Water and Sediment

PubMed Central

de Macedo, A. N.; Vicente, G. H. L.; Nogueira, A. R. A.

2010-01-01

A method for the determination of pesticide residues in water and sediment was developed using the QuEChERS method followed by gas chromatography – mass spectrometry. The method was validated in terms of accuracy, specificity, linearity, detection and quantification limits. The recovery percentages obtained for the pesticides in water at different concentrations ranged from 63 to 116%, with relative standard deviations below 12%. The corresponding results from the sediment ranged from 48 to 115% with relative standard deviations below 16%. The limits of detection for the pesticides in water and sediment were below 0.003 mg L−1 and 0.02 mg kg−1, respectively. PMID:21165598

Bridging the Generation Gap: A Rapid Early Career Hire Training Program

NASA Technical Reports Server (NTRS)

Rieber, Richard R.; Coffee, Thomas; Dong, Shuonan; Infield, Samantha I.; Kilbride, Kendra B.; Seibert, Michael A.; Solish, Benjamin S.

2008-01-01

This paper describes a training program to provide Early Career Hires (ECHs) in the aerospace industry with real, rapid, hands-on exposure to multiple phases and multiple disciplines of flight project development. Such a program has become necessary to close the Generation Gap and ensure that aerospace organizations maintain a highly skilled workforce as experienced personnel begin to retire. This paper discusses the specific motivations for and implementation of such a program at the Jet Propulsion Laboratory. However, the essential features are widely applicable to other NASA centers and organizations delivering large llight systems. This paper details the overall program concept, stages of participation by an ECH, oversight and mentoring, program assessment, training project selection, and facilities requirements.

Demonstration of Multisetting One-Way Einstein-Podolsky-Rosen Steering in Two-Qubit Systems

NASA Astrophysics Data System (ADS)

Xiao, Ya; Ye, Xiang-Jun; Sun, Kai; Xu, Jin-Shi; Li, Chuan-Feng; Guo, Guang-Can

2017-04-01

Einstein-Podolsky-Rosen (EPR) steering describes the ability of one party to remotely affect another's state through local measurements. One of the most distinguishable properties of EPR steering is its asymmetric aspect. Steering can work in one direction but fail in the opposite direction. This type of one-way steering, which is different from the symmetry concepts of entanglement and Bell nonlocality, has garnered much interest. However, an experimental demonstration of genuine one-way EPR steering in the simplest scenario, i.e., one that employs two-qubit systems, is still lacking. In this Letter, we experimentally demonstrate one-way EPR steering with multimeasurement settings for a class of two-qubit states, which are still one-way steerable even with infinite settings. The steerability is quantified by the steering radius, which represents a necessary and sufficient steering criterion. The demonstrated one-way steering in the simplest bipartite quantum system is of fundamental interest and may provide potential applications in one-way quantum information tasks.

Fatty acid profiles, meat quality, and sensory attributes of organic versus conventional dairy beef steers.

PubMed

Bjorklund, E A; Heins, B J; Dicostanzo, A; Chester-Jones, H

2014-03-01

Meat from Holstein and crossbred organic and conventional dairy steers were evaluated and compared for fatty acid profiles, meat quality, sensory attributes, and consumer acceptance. Bull calves (n=49) were randomly assigned to 1 of 3 replicated groups: conventional (CONV), organic (ORG, pasture + concentrate), or grass-fed organic (GRS) and were born at the University of Minnesota West Central Research and Outreach Center (Morris, MN) between March and May 2011. The CONV steers (n=16) were fed a diet that contained 80% concentrate and 20% forage, and ORG steers (n=16) were fed a diet of organic corn, organic corn silage, and organic protein supplement. Furthermore, ORG steers consumed at least 30% of diet dry matter of high-quality organic pasture during the grazing season. The GRS steers (n=17) consumed 100% forage from pasture during the grazing season and high-quality hay or hay silage during the nongrazing season. The ORG steers had fat that was greater in oleic acid (C18:1) than the GRS and CONV steers (47.1, 36.1, and 39.9%, respectively). The GRS steers (21.9%) were lower for monounsaturated fat than the ORG (42.1%) and CONV (40.4%) steers. Furthermore, the GRS steers tended to have greater n-3 fat and had lower n-6 fat than the ORG and CONV steers. Consequently, the GRS (1.4%) steers had a lower n-6-to-n-3 fat ratio than the ORG (12.9%) and CONV (10.0%) steers. The GRS (2.6 kg) steers had steaks that were not different for Warner-Bratzler shear force than ORG (2.3 kg) steaks; however, the GRS steaks tended to have greater shear force than the CONV (2.0 kg) steaks. The 3 steer group had steaks that were not different for color brightness (L*; 0 = black and 100 = white) and yellowness/blueness (b*; positive values = yellow and negative values = blue) values; however, the GRS (10.5) steaks had lower redness/greenness (a*; positive values = red and negative values = green) values than CONV (14.5) steaks. For sensory attributes (0- to 120-point scale), no differences were observed for ORG (71.3) and CONV (69.2) steers for overall consumer liking of the beef; however, the GRS (56.3) steers had the lowest overall liking among beef consumers. The ORG (73.3) steers had greater flavor liking than the GRS (56.8) and CONV (69.2) steers. Conversely, the GRS (6.3) steers had the highest scores for off-flavor (0- to 20-point scale) compared with the ORG (3.9) and CONV (4.1) steers. The results of the current study suggest that a potential market may exist for organic grass-fed dairy steers in the United States, but quality and consistency of the beef needs to be improved. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

46 CFR 169.623 - Power-driven steering systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Power-driven steering systems. 169.623 Section 169.623 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Machinery and Electrical Steering Systems § 169.623 Power-driven steering systems. (a) Power-driven steering...

46 CFR 169.623 - Power-driven steering systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Power-driven steering systems. 169.623 Section 169.623 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Machinery and Electrical Steering Systems § 169.623 Power-driven steering systems. (a) Power-driven steering...

Large angle nonmechanical laser beam steering at 4.6 μm using a digital micromirror device

NASA Astrophysics Data System (ADS)

Lindle, James Ryan; Watnik, Abbie T.

2018-02-01

Large angle, nonmechanical beam steering is demonstrated at 4.62 μm using the digital light processing technology. A 42-deg steering range is demonstrated, limited by the field-of-view of the recollimating lens. The measured diffraction efficiency is 8.1% on-axis and falls-off with a sin2 dependence with the steering angle. However, within the 42-deg steering range, the power varied less than 25%. The profile of the steered laser beam is Gaussian with a divergence of 5.2 mrad. Multibeam, randomly addressable beam steering, is also demonstrated.

Relative entropy of steering: on its definition and properties

NASA Astrophysics Data System (ADS)

Kaur, Eneet; Wilde, Mark M.

2017-11-01

In Gallego and Aolita (2015 Phys. Rev. X 5 041008), the authors proposed a definition for the relative entropy of steering and showed that the resulting quantity is a convex steering monotone. Here we advocate for a different definition for relative entropy of steering, based on well grounded concerns coming from quantum Shannon theory. We prove that this modified relative entropy of steering is a convex steering monotone. Furthermore, we establish that it is uniformly continuous and faithful, in both cases giving quantitative bounds that should be useful in applications. We also consider a restricted relative entropy of steering which is relevant for the case in which the free operations in the resource theory of steering have a more restricted form (the restricted operations could be more relevant in practical scenarios). The restricted relative entropy of steering is convex, monotone with respect to these restricted operations, uniformly continuous, and faithful.

Effects of supplementing zinc or chromium to finishing steers fed ractopamine hydrochloride on growth performance, carcass characteristics, and meat quality.

PubMed

Edenburn, B M; Kneeskern, S G; Bohrer, B M; Rounds, W; Boler, D D; Dilger, A C; Felix, T L

2016-02-01

Objectives were to determine the effects of feeding ractopamine hydrochloride (RAC) with zinc (Zn) and chromium (Cr) on feedlot growth performance, carcass characteristics, and meat quality. Steers ( = 179; initial BW = 533 ± 94 kg) were blocked by BW and allotted to 30 pens, and pens were randomly assigned 1 of 5 treatments: (1) control (CONT), (2) RAC only (RO), (3) RAC + Zn (RZ), (4) RAC + Cr (RC), or (5) RAC + Zn + Cr (RZC). Trace minerals were fed from d 0 to 63 to target 1 g of Zn/steer·d (KemTRACE Zn; Kemin Industries, Inc., Des Moines, IA) and 3 mg Cr/steer·d (KemTRACE Chromium; Kemin Industries, Inc.) for Zn and Cr treatments, respectively. Dry-rolled corn, 0.605 kg/steer, was removed from the diet and 400 mg RAC, per 0.605 kg of ground corn carrier, was top dressed per steer immediately following feed delivery to pens fed RAC. There were no effects ( ≥ 0.45) of trace mineral supplementation on DMI, ADG, or G:F before RAC feeding. There were also no treatment effects ( ≥ 0.46) over all 63 d of the trial on DMI, ADG, or G:F. Despite the lack of differences in live performance, steers fed RO and RC averaged 0.10 kg/d greater ( = 0.10) carcass ADG than steers fed RZC and CONT, while steers fed RZ were intermediate and not different. Steers fed RO had the greatest ( = 0.09) carcass G:F, while steers fed CONT had the least carcass G:F, 0.0875 and 0.0774, respectively. Steers fed RO and RC averaged 5.5 kg heavier ( = 0.09) HCW than steers fed RZC and CONT, while steers fed RZ were intermediate and not different. There were no treatment effects ( ≥ 0.32) on LM area, 12th rib fat, marbling score, KPH, carcass yield, or USDA yield grade and distribution. However, carcasses from steers fed RC had the greatest ( = 0.10) percentage grading USDA Select. There were no treatment effects ( ≥ 0.20) on shear force, intramuscular fat, pH, a*, and b*. Steaks from steers fed RO and RC had 11.4% greater ( = 0.08) cook loss than steaks from steers fed CONT and RZC, whereas steaks from steers fed RZ were intermediate and not different. Also, steaks from steers fed RC had 2.11 units greater ( = 0.03) L* values (i.e., were lighter) than steaks from steers fed RZ; steaks from steers fed CONT, RO, and RZC were intermediate. In feedlot steers, the addition of both Cr and Zn supplementation did not improve growth performance or meat quality when fed in combination with 28 d of RAC supplementation; however, RAC, fed alone or in combination with Cr, did increase HCW.

Steering system for a train of rail-less vehicles

DOEpatents

Voight, Edward T.

1983-01-01

A steering system for use with a multiple vehicle train permits tracking without rails of one vehicle after another. This system is particularly useful for moving conveyor systems into and out of curved paths of room and pillar underground mine installations. The steering system features an elongated steering bar pivotally connected to each of adjacent vehicles at end portions of the bar permitting angular orientation of each vehicle in respect to the steering bar and other vehicles. Each end portion of the steering bar is linked to the near pair of vehicle wheels through wheel yoke pivot arms about king pin type pivots. Movement of the steering bar about its pivotal connection provides proportional turning of the wheels to effect steering and tracking of one vehicle following another in both forward and reverse directions.

Chondrocyte differentiation for auricular cartilage reconstruction using a chitosan based hydrogel.

PubMed

García-López, J; Garciadiego-Cázares, D; Melgarejo-Ramírez, Y; Sánchez-Sánchez, R; Solís-Arrieta, L; García-Carvajal, Z; Sánchez-Betancourt, J I; Ibarra, C; Luna-Bárcenas, G; Velasquillo, C

2015-12-01

Tissue engineering with the use of biodegradable and biocompatible scaffolds is an interesting option for ear repair. Chitosan-Polyvinyl alcohol-Epichlorohydrine hydrogel (CS-PVA-ECH) is biocompatible and displays appropriate mechanical properties to be used as a scaffold. The present work, studies the potential of CS-PVA-ECH scaffolds seeded with chondrocytes to develop elastic cartilage engineered-neotissues. Chondrocytes isolated from rabbit and swine elastic cartilage were independently cultured onto CS-PVA-ECH scaffolds for 20 days to form the appropriate constructs. Then, in vitro cell viability and morphology were evaluated by calcein AM and EthD-1 assays and Scanning Electron Microscopy (SEM) respectively, and the constructs were implanted in nu/nu mice for four months, in order to evaluate the neotissue formation. Histological analysis of the formed neotissues was performed by Safranin O, Toluidine blue (GAG's), Verhoeff-Van Gieson (elastic fibers), Masson's trichrome (collagen) and Von Kossa (Calcium salts) stains and SEM. Results indicate appropriate cell viability, seeded with rabbit or swine chondrocyte constructs; nevertheless, upon implantation the constructs developed neotissues with different characteristics depending on the animal species from which the seeded chondrocytes came from. Neotissues developed from swine chondrocytes were similar to auricular cartilage, while neotissues from rabbit chondrocytes were similar to hyaline cartilage and eventually they differentiate to bone. This result suggests that neotissue characteristics may be influenced by the animal species source of the chondrocytes isolated.

Role of density gradient driven trapped electron mode turbulence in the H-mode inner core with electron heating

DOE PAGES

Ernst, D. R.; Burrell, K. H.; Guttenfelder, W.; ...

2016-05-10

In a series of DIII-D [J. L. Luxon, Nucl. Fusion 42 614 (2002)] low torque quiescent H-mode experiments show that density gradient driven TEM (DGTEM) turbulence dominates the inner core of H-Mode plasmas during strong electron cyclotron heating (ECH). By adding 3.4 MW ECH doubles T e/T i from 0.5 to 1.0, which halves the linear DGTEM critical density gradient, locally reducing density peaking, while transport in all channels displays extreme stiffness in the density gradient. This then suggests fusion -heating may degrade inner core confinement in H-Mode plasmas with moderate density peaking and low collisionality, with equal electron andmore » ion temperatures, key conditions expected in burning plasmas. Gyrokinetic simulations using GYRO [J. Candy and R. E. Waltz, J. Comp. Phys. 186 545 (2003)] (and GENE [F. Jenko et al., Phys. Plasmas 7, 1904 (2000)]) closely match not only particle, energy, and momentum fluxes, but also density fluctuation spectra from Doppler Backscattering (DBS), with and without ECH. Inner core DBS density fluctuations display discrete frequencies with adjacent toroidal mode numbers, which we identify as DGTEMs. GS2 [W. Dorland et al., Phys. Rev. Lett. 85 5579 (2000)] predictions show the DGTEM can be suppressed, to avoid degradation with electron heating, by broadening the current density profile to attain q 0 > q min > 1.« less

Suppression of fat deposition in broiler chickens by (-)-hydroxycitric acid supplementation: A proteomics perspective

PubMed Central

Peng, Mengling; Han, Jing; Li, Longlong; Ma, Haitian

2016-01-01

(-)-Hydroxycitric acid (HCA) suppresses fatty acid synthesis in animals, but its biochemical mechanism in poultry is unclear. This study identified the key proteins associated with fat metabolism and elucidated the biochemical mechanism of (-)-HCA in broiler chickens. Four groups (n = 30 each) received a diet supplemented with 0, 1000, 2000 or 3000 mg/kg (-)-HCA for 4 weeks. Of the differentially expressed liver proteins, 40 and 26 were identified in the mitochondrial and cytoplasm respectively. Pyruvate dehydrogenase E1 components (PDHA1 and PDHB), dihydrolipoyl dehydrogenase (DLD), aconitase (ACO2), a-ketoglutarate dehydrogenase complex (DLST), enoyl-CoA hydratase (ECHS1) and phosphoglycerate kinase (PGK) were upregulated, while NADP-dependent malic enzyme (ME1) was downregulated. Biological network analysis showed that the identified proteins were involved in glycometabolism and lipid metabolism, whereas PDHA1, PDHB, ECHS1, and ME1 were identified in the canonical pathway by Ingenuity Pathway Analysis. The data indicated that (-)-HCA inhibited fatty acid synthesis by reducing the acetyl-CoA supply, via promotion of the tricarboxylic acid cycle (upregulation of PDHA1, PDHB, ACO2, and DLST expression) and inhibition of ME1 expression. Moreover, (-)-HCA promoted fatty acid beta-oxidation by upregulating ECHS1 expression. These results reflect a biochemically relevant mechanism of fat reduction by (-)-HCA in broiler chickens. PMID:27586962

Evaluation of various QuEChERS based methods for the analysis of herbicides and other commonly used pesticides in polished rice by LC-MS/MS.

PubMed

Pareja, Lucía; Cesio, Verónica; Heinzen, Horacio; Fernández-Alba, Amadeo R

2011-02-15

Four different extraction and clean-up protocols based on the QuEChERS method were compared for the development of an optimized sample preparation procedure for the multiresidue analysis of 16 commonly applied herbicides in rice crops using LC-QqQ/MS. Additionally the methods were evaluated for the analysis of 26 insecticides and fungicides currently used in rice crops. The methods comprise, in general, the hydratation of the sample with water followed by the extraction with acetonitrile, phase separation with the addition of different salts and finally a clean-up step with various sorbents. Matrix effects were evaluated for the 4 studied methods using LC-QqQ/MS. Additionally LC-TOF/MS was used to compare the co-extractants obtained with the four assayed methodologies. Thirty-six pesticides presented good performance with recoveries in the range 70-120% and relative standard deviations below 20% using 7.5 g of milled polished rice and the buffered acetate QuEChERS method without clean-up at both fortification levels: 10 and 300 μg kg(-1). The other six pesticides presented low recovery rates, nevertheless all these analytes could be analyzed with at least one of the other three studied procedures. Copyright © 2010. Published by Elsevier B.V.

Initial results for a 170 GHz high power ITER waveguide component test stand

NASA Astrophysics Data System (ADS)

Bigelow, Timothy; Barker, Alan; Dukes, Carl; Killough, Stephen; Kaufman, Michael; White, John; Bell, Gary; Hanson, Greg; Rasmussen, Dave

2014-10-01

A high power microwave test stand is being setup at ORNL to enable prototype testing of 170 GHz cw waveguide components being developed for the ITER ECH system. The ITER ECH system will utilize 63.5 mm diameter evacuated corrugated waveguide and will have 24 >150 m long runs. A 170 GHz 1 MW class gyrotron is being developed by Communications and Power Industries and is nearing completion. A HVDC power supply, water-cooling and control system has been partially tested in preparation for arrival of the gyrotron. The power supply and water-cooling system are being designed to operate for >3600 second pulses to simulate the operating conditions planned for the ITER ECH system. The gyrotron Gaussian beam output has a single mirror for focusing into a 63.5 mm corrugated waveguide in the vertical plane. The output beam and mirror are enclosed in an evacuated duct with absorber for stray radiation. Beam alignment with the waveguide is a critical task so a combination of mirror tilt adjustments and a bellows for offsets will be provided. Analysis of thermal patterns on thin witness plates will provide gyrotron mode purity and waveguide coupling efficiency data. Pre-prototype waveguide components and two dummy loads are available for initial operational testing of the gyrotron. ORNL is managed by UT-Battelle, LLC, for the U.S. Dept. of Energy under Contract DE-AC-05-00OR22725.

42GHz ECRH assisted Plasma Breakdown in tokamak SST-1

NASA Astrophysics Data System (ADS)

Shukla, B. K.; Pradhan, S.; Patel, Paresh; Babu, Rajan; Patel, Jatin; Patel, Harshida; Dhorajia, Pragnesh; Tanna, V.; Atrey, P. K.; Manchanda, R.; Gupta, Manoj; Joisa, Shankar; Gupta, C. N.; Danial, Raju; Singh, Prashant; Jha, R.; Bora, D.

2015-03-01

In SST-1, 42GHz ECRH system has been commissioned to carry out breakdown and heating experiments at 0.75T and 1.5T operating toroidal magnetic fields. The 42GHz ECRH system consists of high power microwave source Gyrotron capable to deliver 500kW microwave power for 500ms duration, approximately 20 meter long transmission line and a mirror based launcher. The ECRH power in fundamental O-mode & second harmonic X-mode is launched from low field side (radial port) of the tokamak. At 0.75T operation, approximately 300 kW ECH power is launched in second harmonic X-mode and successful ECRH assisted breakdown is achieved at low loop_voltage ~ 3V. The ECRH power is launched around 45ms prior to loop voltage. The hydrogen pressure in tokamak is maintained ~ 1×10-5mbar and the pre-ionized density is ~ 4×1012/cc. At 1.5T operating toroidal magnetic field, the ECH power is launched in fundamental O-mode. The ECH power at fundamental harmonic is varied from 100 kW to 250 kW and successful breakdown is achieved in all ECRH shots. In fundamental harmonic there is no delay in breakdown while at second harmonic ~ 40ms delay is observed, which is normal in case of second harmonic ECRH assisted breakdown.

Influence of feed efficiency classification on diet digestibility and growth performance of beef steers.

PubMed

Russell, J R; Minton, N O; Sexten, W J; Kerley, M S; Hansen, S L

2016-04-01

The diet digestibility and feed efficiency (FE) relationship is not well characterized in cattle. The study objective was to determine effects of growing phase FE and diet as well as finishing phase diet on diet digestibility and finishing phase FE. Two groups, totaling 373 crossbred steers, were fed for 70 d at the University of Missouri for the growing phase and then shipped to Iowa State University (ISU) for finishing. GrowSafe feed bunks were used during both the growing and the finishing phases. Steers were fed either growing phase whole shell corn (G-Corn) or growing phase roughage-based (G-Rough) diets. Within each group, the 12 greatest and 12 least feed efficient steers from each growing diet ( = 96 total; 48 steers/group; 488 ± 5 kg) were selected for further evaluation. At ISU, steers were fed an average of 10 g TiO/steer daily in receiving phase diets similar to growing diets for 15 d, with fecal grab samples collected on d 14 and 15 to determine diet DM digestibility during receiving (GDMdig). For finishing, steers were transitioned to byproduct-based diets (F-Byp) or corn-based diets (F-Corn) with 12 steers per growing-finishing diet combination per group. Optaflexx (200 mg/d) was fed for 28 d before harvest, and the TiO protocol was repeated immediately before introducing Optaflexx to determine diet DM digestibility during finishing (FDMdig). Data from the 2 groups (96 steers) were pooled, and steers were ranked by growing phase G:F and then classified as the 24 greatest feed efficient (HFE) or 24 least feed efficient (LFE) steers from each growing diet. Data were analyzed using PROC MIXED of SAS with group applied as a fixed effect. There was a positive correlation between GDMdig and FDMdig for steers fed nutritionally similar diets during both feeding phases, G-Rough/F-Byp steers ( = 0.68, < 0.01) and G-Corn/F-Corn steers ( = 0.49, = 0.02), but a negative correlation for G:F between phases in G-Rough/F-Corn steers ( = -0.57, < 0.01). Finishing G:F was greater in HFE steers versus LFE steers ( = 0.04), but there was no difference ( ≥ 0.5) in GDMdig or FDMdig due to FE classification. There was a positive correlation for DM digestibility between feeding phases when steers were grown and finished on similar diets. Overall, FE was repeatable but was negatively correlated between phases when steers were roughage grown and corn finished, reinforcing the idea that cattle should be FE tested using diet types similar to the production environment of interest.

Performance, insulin sensitivity, carcass characteristics, and fatty acid profile of beef from steers fed microalgae.

PubMed

Carvalho, J R R; Brennan, K M; Ladeira, M M; Schoonmaker, J P

2018-05-25

Heterotrophic production of microalgae biomass provides a consistent, high quality source of docosahexaenoic acid (DHA; C22:6 n-3) in triglyceride oils that could be used as a ration supplement for feedlot steers to improve nutritional qualities of beef. Sixty Angus × Simmental steers (438 ± 6.4 kg) were allotted to 2 treatments (30 steers each, 6 pens, 5 steers/pen) to determine the effects of ForPLUS (DHA-rich microalgae Aurantiochytrium limacinum; 63.6 % fat; 17.9% DHA; 30 mg/kg Sel-Plex; Alltech Inc.) on performance, insulin sensitivity, LM fatty acid composition, and meat quality. Steers were fed basal diets containing 45% corn, 30% distillers dried grains with solubles, 20% corn silage, and 5% supplement. Basal diets were formulated to contain 16.1% CP and 1.32 Mcal/kg NEg. Treatments were delivered to steers in a ground corn based top-dress (454 g total/steer) and contained no microalgae for control steers or 100 g/steer daily of ForPLUS for microalgae steers. A glucose tolerance test (GTT) was performed 10 d prior to slaughter. Steers were slaughtered when a target pen BW of 621 kg was achieved. Fatty acid oxidation potential was determined by measuring thiobarbituric acid reactive substances (TBARS) on LM samples collected 24 h after slaughter and aged for 48 h or 21 d. Weight and BW gain did not differ during the study (P ≥ 0.13); however, steers fed microalgae remained in the feedlot 7 more d compared to steers fed the control diet (111 vs. 104 d; P = 0.04). Overall DMI decreased (P = 0.002) and G:F increased during the second half of the study (P = 0.04) in steers fed microalgae compared to steers fed the control diet. Steers fed microalgae secreted less insulin (P = 0.01) and took longer to clear glucose (P = 0.01) during a 2 h GTT. Carcass traits did not differ between treatments (P ≥ 0.23). Microalgae had no effect on n-6 content (P = 0.67), but more than doubled the n-3 fatty acid percentage and the n3:n6 ratio of the LM (P < 0.0001). The percentage of n-3 fatty acids C20:5 and C22:6 were increased (P < 0.0001) 4-fold and 6.25-fold, respectively, by microalgae supplementation. Concentration of TBARS did not differ in LM aged for 48 h (P = 0.91); however, when aged for 21 d, steers fed microalgae tended to produce LM with greater TBARS concentration compared to steers fed the control diet (P = 0.08). In conclusion, DHA-rich microalgae decreased DMI of steers, and increased n-3 fatty acids and beef oxidation in steaks aged for 21 d.

One-way EPR steering and genuine multipartite EPR steering

NASA Astrophysics Data System (ADS)

He, Qiongyi; Reid, Margaret D.

2012-11-01

We propose criteria and experimental strategies to realise the Einstein-Podolsky-Rosen (EPR) steering nonlocality. One-way steering can be obtained where there is asymmetry of thermal noise on each system. We also present EPR steering inequalities that act as signatures and suggest how to optimise EPR correlations in specific schemes so that the genuine multipartite EPR steering nonlocality (EPR paradox) can also possibly be realised. The results presented here also apply to the spatially separated macroscopic atomic ensembles.

46 CFR 58.25-10 - Main and auxiliary steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Main and auxiliary steering gear. 58.25-10 Section 58.25... AUXILIARY MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-10 Main and auxiliary steering gear. (a) Power-operated main and auxiliary steering gear must be separate systems that are independent throughout their...

46 CFR 196.37-33 - Instructions for changing steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Instructions for changing steering gear. 196.37-33... steering gear. (a) Instructions in at least 1/2 inch letters and figures shall be posted in the steering engineroom, relating in order, the different steps to be taken in changing to the emergency steering gear...

The influence of Unruh effect on quantum steering for accelerated two-level detectors with different measurements

NASA Astrophysics Data System (ADS)

Liu, Tonghua; Wang, Jieci; Jing, Jiliang; Fan, Heng

2018-03-01

We propose a tight measure of quantum steering and study the dynamics of steering in a relativistic setting via different quantifiers. We present the dynamics of steering between two correlated Unruh-Dewitt detectors when one of them locally interacts with external scalar field. We find that the quantum steering, either measured by the entropic steering inequality or the Cavalcanti-Jones-Wiseman-Reid inequality, is fragile under the influence of Unruh thermal noise. The quantum steering is found always asymmetric and the asymmetry is extremely sensitive to the initial state parameter. In addition, the steering-type quantum correlations experience "sudden death" for some accelerations, which are quite different from the behaviors of other quantum correlations in the same system. It is worth noting that the domination value of the tight quantum steering exists a transformation point with increasing acceleration. We also find that the robustness of quantum steerability under the Unruh thermal noise can be realized by choosing the smallest energy gap in the detectors.

The influence of oscillating dietary protein concentrations on finishing cattle. I. Feedlot performance and odorous compound production.

PubMed

Archibeque, S L; Miller, D N; Freetly, H C; Berry, E D; Ferrell, C L

2007-06-01

We hypothesized that oscillation of the dietary CP concentration, which may improve N retention of finishing beef steers, would reduce production of manure odor compounds and total N inputs while yielding comparable performance. Charolais-sired steers (n = 144; 303 +/- 5 kg of initial BW) were used in a completely randomized block design (6 pens/treatment). The steers were fed to 567 kg of BW on the following finishing diets, which were based on dry-rolled corn: 1) low (9.1% CP), 2) medium (11.8% CP), 3) high (14.9% CP), or 4) low and high oscillated on a 48-h interval for each feed (oscillating). Steers fed low tended (P = 0.08) to have less DMI (7.80 kg/d) than steers fed medium (8.60 kg/d) or oscillating (8.67 kg/d), but not less than steers fed high (8.12 kg/d). Daily N intake was greatest (P < 0.01) for steers fed high (189 g), intermediate for medium (160 g) and oscillating (164 g), and least for low (113 g). The ADG was lower (P < 0.01) for steers fed low (1.03 kg) than for those fed medium (1.45 kg), high (1.45 kg), or oscillating (1.43 kg). Similarly, steers fed low had a lower adjusted fat thickness (P < 0.01) and yield grade (P = 0.05) and tended (P = 0.10) to have less marbling than steers fed the other 3 diets. In slurries with feces, urine, soil, and water, incubated for 35 d, nonsoluble CP was similar among slurries from steers fed medium, high, or oscillating, but was less (P < 0.01) in slurries from steers fed low. However, throughout the incubation period, slurries from steers fed high or oscillating had greater (P < 0.01) concentrations of total aromatics and ammonia than those from steers fed low or medium. Also, the slurries from steers fed oscillating had greater (P < 0.01) concentrations of branched-chain VFA than manure slurries from steers fed any of the other diets. These data indicate that although there is no apparent alteration in the performance of finishing steers fed diets with oscillation of the dietary protein, there may be undesirable increases in the production of compounds associated with malodor.

Comparisons of Measurements and Simulations of Turbulence and Transport for DIII-D Discharges with Off-Axis Modulated ECH

NASA Astrophysics Data System (ADS)

Bravenec, R. V.; Ross, D. W.; Austin, M. E.; Gentle, K. W.; Deboo, J. C.; DIII-D Team; McKee, G. R.; Dorland, W.; Rhodes, T. L.; Zeng, L.

2002-11-01

Experiments to elucidate the nature of electron thermal transport have been conducted in DIII-D plasmas using modulated off-axis electron-cyclotron heating (ECH). Density fluctuations were measured using beam-emission spectroscopy, microwave reflectometry, and far-infrared scattering. Simulations of the experiment are performed with the gyrokinetic and gyrofluid flux-tube codes GS2(F. Jenko, W. Dorland, M. Kotschenreuther, and B.N. Rogers, Phys. Plasmas 7), 1904 (2000) and refs. therein. and GRYFFIN,(W. Dorland and G.W. Hammett, Phys. Fluids B 5), 812 (1993); M.A. Beer and G.W. Hammett, Phys. Plasmas 3, 4046 (1996). respectively. Comparisons of experiment and simulation results for the fluctuations and transport fluxes (ion and electron) will be presented for both time-averaged and modulated quantities.

Observation of magnetic fluctuations and rapid density decay of magnetospheric plasma in Ring Trap 1

NASA Astrophysics Data System (ADS)

Saitoh, H.; Yoshida, Z.; Morikawa, J.; Yano, Y.; Mikami, H.; Kasaoka, N.; Sakamoto, W.

2012-06-01

The Ring Trap 1 device, a magnetospheric configuration generated by a levitated dipole field magnet, has created high-β (local β ˜ 70%) plasma by using electron cyclotron resonance heating (ECH). When a large population of energetic electrons is generated at low neutral gas pressure operation, high frequency magnetic fluctuations are observed. When the fluctuations are strongly excited, rapid loss of plasma was simultaneously observed especially in a quiet decay phase after the ECH microwave power is turned off. Although the plasma is confined in a strongly inhomogeneous dipole field configuration, the frequency spectra of the fluctuations have sharp frequency peaks, implying spatially localized sources of the fluctuations. The fluctuations are stabilized by decreasing the hot electron component below approximately 40%, realizing stable high-β confinement.

Application of ECH to the study of transport in ITER baseline scenario-like discharges in DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinsker, R. I.; Austin, M. E.; Ernst, D. R.

Recent DIII-D experiments in the ITER Baseline Scenario (IBS) have shown strong increases in fluctuations and correlated reduction of confinement associated with entering the electron-heating-dominated regime with strong electron cyclotron heating (ECH). The addition of 3.2 MW of 110 GHz EC power deposited at ρ~0.42 to IBS discharges with ~3 MW of neutral beam injection causes large increases in low-k and medium-k turbulent density fluctuations observed with Doppler backscatter (DBS), beam emission spectroscopy (BES) and phase-contrast imaging (PCI) diagnostics, correlated with decreases in the energy, particle, and momentum confinement times. Power balance calculations show the electron heat diffusivity χ emore » increases significantly in the mid-radius region 0.4« less

Application of ECH to the study of transport in ITER baseline scenario-like discharges in DIII-D

DOE PAGES

Pinsker, R. I.; Austin, M. E.; Ernst, D. R.; ...

2015-03-12

Recent DIII-D experiments in the ITER Baseline Scenario (IBS) have shown strong increases in fluctuations and correlated reduction of confinement associated with entering the electron-heating-dominated regime with strong electron cyclotron heating (ECH). The addition of 3.2 MW of 110 GHz EC power deposited at ρ~0.42 to IBS discharges with ~3 MW of neutral beam injection causes large increases in low-k and medium-k turbulent density fluctuations observed with Doppler backscatter (DBS), beam emission spectroscopy (BES) and phase-contrast imaging (PCI) diagnostics, correlated with decreases in the energy, particle, and momentum confinement times. Power balance calculations show the electron heat diffusivity χ emore » increases significantly in the mid-radius region 0.4« less

Analysis of hydraulic steering system of tracked all-terrain vehicles' articulated mechanism

NASA Astrophysics Data System (ADS)

Meng, Zhongliang; Zang, Hao

2018-04-01

As for the researches on the dynamic characteristics of tracked all-terrain vehicles' articulated mechanism, the hydraulic feature of their steering system needs researching more, apart from the study on mechanical models. According to the maximum pressure required by the steering system of tracked all-terrain vehicle and the principle of the steering system, this paper conducts an analysis of the hydraulic steering system of the articulated mechanism. Based on the structure principle of the steering gear, a simulation model of the tracked all-terrain vehicle turning left is built. When building the simulation model of the steering gear, it makes a simulation analysis, taking the tracked all-terrain vehicle turning left as an example.

52. Patent steering gear, hatch and steering compass binnacle, view ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

52. Patent steering gear, hatch and steering compass binnacle, view from starboard looking aft. Photograph by Jet Lowe, April 1988. - Ship BALCLUTHA, 2905 Hyde Street Pier, San Francisco, San Francisco County, CA

Relationship between antioxidant capacity, oxidative stress, and feed efficiency in beef steers.

PubMed

Russell, J R; Sexten, W J; Kerley, M S; Hansen, S L

2016-07-01

Feed efficiency (FE) can vary between individuals but sources of variation are not well characterized. Oxidative stress is among the biological mechanisms believed to contribute to variation. The objective of this study was to evaluate the relationship between FE, antioxidant activity, and oxidative stress in feedlot steers representing phenotypic extremes for FE. Crossbred beef steers ( = 181) fed 70-d growing phase (GP) whole-shell corn-based (G-Corn) or rye baleage and soybean hull-based (G-Rough) diets in GrowSafe bunks at the University of Missouri were shipped to Iowa State University where the 12 most feed efficient (HFE) and 12 least feed efficient (LFE) steers from each diet (n = 48; 467 kg [SD 51]) were selected for evaluation. Steers received diets similar to GP diets, and 3 d after arrival, blood was sampled to evaluate antioxidant activity and oxidative stress markers for the GP following transit. Steers were transitioned to finishing phase (FP) cracked corn-based (F-Corn) or dried distillers' grains and soybean hull-based (F-Byp) diets, and on FP d 97, blood samples for the FP were collected. Data for the GP were analyzed as a 2 × 2 factorial, and data for the FP were analyzed as a 2 × 2 × 2 factorial using PROC MIXED of SAS. No GP diet × FP diet, FP diet × FE group, or 3-way interactions were noted ( ≥ 0.11) for FP measures. Steers fed the G-Rough diet had greater ( = 0.04) GP plasma protein carbonyl concentrations. During the GP, HFE steers had greater ( ≤ 0.04) protein carbonyl and ratio of oxidized:reduced blood lysate glutathione concentrations than LFE steers. There were GP diet × FE group interactions ( ≤ 0.03) during the GP and FP. During the GP, total blood lysate superoxide dismutase (SOD) activity was greater ( ≤ 0.03) in G-Rough/LFE steers than in G-Rough/HFE and G-Corn/LFE steers; G-Corn/HFE steers were intermediate. The G-Rough/LFE steers had greater ( < 0.04) glutathione peroxidase (GPX) activity than other groups and greater ( = 0.03) plasma malondialdehyde concentrations than G-Corn/LFE steers. During the FP, the G-Rough/LFE steers had greater ( ≤ 0.04) GPX activity than G-Rough/HFE and G-Corn/LFE steers; G-Corn/HFE steers were intermediate. The F-Byp diet had greater ( < 0.01) protein carbonyl than the F-Corn diet, and no other FP diet effects were noted ( ≥ 0.3) for any FP measures. The GP diet and FE groups had stronger relationships with antioxidant activity and oxidative stress markers measured for the GP than for the FP. Overall, antioxidant activity may play a role in FE as LFE steers, driven largely by G-Rough/LFE steers, had greater SOD activity and GPX activity than HFE steers, potentially using a greater proportion of energy otherwise available for tissue accretion.

49 CFR 393.209 - Steering wheel systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PARTS AND ACCESSORIES...) Steering column. The steering column must be securely fastened. (d) Steering system. Universal joints and...

49 CFR 393.209 - Steering wheel systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PARTS AND ACCESSORIES...) Steering column. The steering column must be securely fastened. (d) Steering system. Universal joints and...

49 CFR 393.209 - Steering wheel systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PARTS AND ACCESSORIES...) Steering column. The steering column must be securely fastened. (d) Steering system. Universal joints and...

49 CFR 393.209 - Steering wheel systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PARTS AND ACCESSORIES...) Steering column. The steering column must be securely fastened. (d) Steering system. Universal joints and...

49 CFR 393.209 - Steering wheel systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PARTS AND ACCESSORIES...) Steering column. The steering column must be securely fastened. (d) Steering system. Universal joints and...

Method of Controlling Steering of a Ground Vehicle

NASA Technical Reports Server (NTRS)

Guo, Raymond (Inventor); Atluri, Venkata Prasad (Inventor); Bluethmann, William J. (Inventor); Lee, Chunhao J. (Inventor); Vitale, Robert L. (Inventor); Dawson, Andrew D. (Inventor)

2016-01-01

A method of controlling steering of a vehicle through setting wheel angles of a plurality of modular electronic corner assemblies (eModules) is provided. The method includes receiving a driving mode selected from a mode selection menu. A position of a steering input device is determined in a master controller. A velocity of the vehicle is determined, in the master controller, when the determined position of the steering input device is near center. A drive mode request corresponding to the selected driving mode to the plurality of steering controllers is transmitted to the master controller. A required steering angle of each of the plurality of eModules is determined, in the master controller, as a function of the determined position of the steering input device, the determined velocity of the vehicle, and the selected first driving mode. The eModules are set to the respective determined steering angles.

Monogamy of quantum steering

NASA Astrophysics Data System (ADS)

Milne, Antony; Jennings, David; Jevtic, Sania; Rudolph, Terry; Wiseman, Howard

The quantum steering ellipsoid formalism naturally extends the Bloch vector picture for qubits to provide a visualisation of two-qubit systems. If Alice and Bob share a correlated state then a local measurement by Bob steers Alice's qubit inside the Bloch sphere; given all possible measurements by Bob, the set of states to which Alice can be steered form her steering ellipsoid. We apply the formalism to a three-party scenario and find that steering ellipsoid volumes obey a simple monogamy relation. This gives us a novel derivation of the well-known CKW (Coffman-Kundu-Wootters) inequality for entanglement monogamy. The geometric perspective also identifies a new measure of quantum correlation, `obesity', and a set of `maximally obese' states that saturate the steering monogamy bound. These states are found to have extremal quantum correlation properties that are significant in the steering ellipsoid picture and for the study of two-qubit states in general.

Effect of ractopamine hydrochloride (Optaflexx) dose and duration on growth performance and carcass characteristics of finishing steers.

PubMed

Bittner, C J; Crawford, G I; Berger, L L; Holt, S; Pritchard, R R; Platter, W J; Van Koevering, M T; Pyatt, N A; Erickson, G E

2016-12-01

Three experiments evaluated the effects of ractopamine hydrochloride (RAC) dose and duration on growth performance and carcass characteristics of feedlot steers. In total, 1,509 crossbred steers (530 kg initial BW [SD 22]) were used in a randomized complete block design using a 3 × 3 factorial treatment structure. Treatments consisted of RAC dose (0, 100, or 200 mg/steer daily) and duration (28, 35, or 42 d) of RAC feeding prior to harvest. Initiation of RAC dose was staggered (7 d apart) based on RAC duration, which resulted in common days on feed among treatments. Data from the 3 experiments were combined for statistical analyses. There were no RAC dose × duration interactions ( ≥ 0.85) for growth performance. Live final BW was not different ( ≥ 0.24) as RAC dose increased. Dry matter intake linearly decreased ( < 0.01) as RAC dose increased. Live ADG and G:F linearly increased ( ≤ 0.01) as RAC dose increased. Carcass-adjusted ADG and G:F linearly increased ( ≤ 0.02) as RAC dose increased. Compared with steers fed 0 mg RAC/steer daily, G:F was improved by 5.0 and 13.0% when steers were fed 100 ( = 0.31) and 200 ( = 0.01) mg RAC/steer daily, respectively. Hot carcass weight tended ( = 0.10) to linearly increase as RAC dose increased, with carcasses from steers fed 100 ( = 0.38) and 200 ( = 0.10) mg RAC/steer daily being 2.2 and 4.1 kg heavier, respectively, than carcasses from steers fed 0 mg RAC/steer daily. Increasing RAC dose linearly ( < 0.01) increased LM area and linearly ( = 0.02) decreased marbling score. Live final BW was not different ( ≥ 0.60) among RAC durations. Carcass-adjusted final BW, ADG, and G:F were not different ( ≥ 0.41) as RAC duration increased. Carcass traits did not differ ( ≥ 0.18) among RAC duration. Feeding 200 mg RAC/steer daily improved ADG, feed efficiency, and HCW. Increasing the feeding duration of RAC had no effect of growth performance or carcass characteristics. These data indicate that feeding 200 mg RAC/steer daily for 28 d improves steer growth performance.

Effects of tilmicosin phosphate, administered prior to transport or at time of arrival, and feeding of chlortetracycline, after arrival in a feedlot, on Mannheimia haemolytica in nasal secretions of transported steers.

PubMed

Frank, G H; Duff, G C

2000-12-01

To determine effects of time of administration of tilmicosin and feeding of chlortetracycline on colonization of the nasopharynx of transported cattle by Mannheimia haemolytica (MH). 454 steers (body weight, 200 kg). 3 studies included 4 truckloads of steers assembled and processed in the southeastern United States. For each truckload of steers, a third received tilmicosin before transportation (PRIOR), then all were transported to a feedlot in New Mexico (23 hours). At arrival (day 0), another third received tilmicosin (ARR). The remaining third did not receive tilmicosin (control steers [CTR]). Steers in studies 1 and 2 were housed in a feedlot, and steers in study 3 were housed on wheat pasture. One half of the steers from each group in studies 2 and 3 were fed chlortetracycline on days 5 to 9. Steer with signs of respiratory tract disease were treated. Nasal swab specimens were examined for MH to determine colonization. PRIOR and ARR steers had a lower incidence of respiratory tract disease and MH colonization than CTR steers, but PRIOR and ARR steers did not differ. Feeding chlortetracycline did not have an effect. Tilmicosin can inhibit MH from colonizing the nasopharynx of cattle. Because tilmicosin inhibits the growth of MH in the respiratory tract, medication with tilmicosin prior to transport should reduce the incidence of acute respiratory tract disease during the first week at the feedlot when calves are most susceptible to infectious organisms.

Multipartite Gaussian steering: Monogamy constraints and quantum cryptography applications

NASA Astrophysics Data System (ADS)

Xiang, Yu; Kogias, Ioannis; Adesso, Gerardo; He, Qiongyi

2017-01-01

We derive laws for the distribution of quantum steering among different parties in multipartite Gaussian states under Gaussian measurements. We prove that a monogamy relation akin to the generalized Coffman-Kundu-Wootters inequality holds quantitatively for a recently introduced measure of Gaussian steering. We then define the residual Gaussian steering, stemming from the monogamy inequality, as an indicator of collective steering-type correlations. For pure three-mode Gaussian states, the residual acts as a quantifier of genuine multipartite steering, and is interpreted operationally in terms of the guaranteed key rate in the task of secure quantum secret sharing. Optimal resource states for the latter protocol are identified, and their possible experimental implementation discussed. Our results pin down the role of multipartite steering for quantum communication.

Tunable Graphene Metasurface Reflectarray for Cloaking, Illusion, and Focusing

NASA Astrophysics Data System (ADS)

Biswas, Sudipta Romen; Gutiérrez, Cristian E.; Nemilentsau, Andrei; Lee, In-Ho; Oh, Sang-Hyun; Avouris, Phaedon; Low, Tony

2018-03-01

This paper is a contribution to the Physical Review Applied collection in memory of Mildred S. Dresselhaus. We present a graphene-based metasurface that can be actively tuned between different regimes of operation, such as anomalous beam steering and focusing, cloaking, and illusion optics, by applying electrostatic gating without modifying the geometry of the metasurface. The metasurface is designed by placing graphene ribbons on a dielectric cavity resonator, where interplay between geometric plasmon resonances in the ribbons and Fabry-Perot resonances in the cavity is used to achieve a 2 π phase shift. As a proof of concept, we demonstrate that the wave front of the field reflected from a triangular bump covered by the metasurface can be tuned by applying electric bias so as to resemble that of a bare plane and of a spherical object. Moreover, reflective focusing and the change of the reflection direction for the above mentioned cases are also shown.

Dynamic modelling and experimental validation of three wheeled tilting vehicles

NASA Astrophysics Data System (ADS)

Amati, Nicola; Festini, Andrea; Pelizza, Luigi; Tonoli, Andrea

2011-06-01

The present paper describes the study of the stability in the straight running of a three-wheeled tilting vehicle for urban and sub-urban mobility. The analysis was carried out by developing a multibody model in the Matlab/SimulinkSimMechanics environment. An Adams-Motorcycle model and an equivalent analytical model were developed for the cross-validation and for highlighting the similarities with the lateral dynamics of motorcycles. Field tests were carried out to validate the model and identify some critical parameters, such as the damping on the steering system. The stability analysis demonstrates that the lateral dynamic motions are characterised by vibration modes that are similar to that of a motorcycle. Additionally, it shows that the wobble mode is significantly affected by the castor trail, whereas it is only slightly affected by the dynamics of the front suspension. For the present case study, the frame compliance also has no influence on the weave and wobble.

Growth, carcass characteristics, and profitability of organic versus conventional dairy beef steers.

PubMed

Bjorklund, E A; Heins, B J; Dicostanzo, A; Chester-Jones, H

2014-03-01

Bull calves (n=49), born at the University of Minnesota West Central Research and Outreach Center (Morris) between March and May 2011, were used to compare growth measurements and profitability of conventional and organic dairy steers. Calves were assigned to 1 of 3 replicated groups at birth: conventional (CONV; n=16), organic (pasture and concentrate; ORG; n=16), or organic grass only (GRS; n=17), and analysis of variables was on a pen basis. Breed groups of calves were Holstein (HO; n=9); Holsteins (n=11) maintained at 1964 breed average level; crossbreds (n=19) including combinations of HO, Montbéliarde, and Swedish Red; and crossbreds (n=10) including combinations of HO, Jersey, Swedish Red, and Normande. The CONV steers were fed a diet of 80% concentrate and 20% forage. The ORG steers were fed a diet of organic corn, organic corn silage, and at least 30% of their diet consisted of organic pasture during the grazing season. The GRS steers grazed pasture during the grazing season and were fed high-quality hay or hay silage during the nongrazing season. Intakes of a total mixed ration were recorded daily with herd management software. A profit function was defined to include revenues and expenses for beef value, feed intake, pasture intake, health cost, and yardage. The GRS (358.6 kg) steers had lesser total gains from birth to slaughter than ORG (429.6 kg) and CONV (534.5 kg) steers. Furthermore, the GRS (0.61 kg/d) steers had lesser average daily gain from birth compared with ORG (0.81 kg/d) and CONV (1.1 kg/d) steers. The GRS and ORG steers had smaller rib eye area (49.5 and 65.8 cm(2), respectively) compared with CONV (75.4 cm(2)) steers. For profitability, GRS steers had 43% greater profit than CONV steers due to organic beef price premiums and lower feed costs. On the other hand, ORG steers had substantially less profit than CONV steers. The higher cost of production for the ORG steers is due to the extreme high value of organic corn. The results of the current study illustrate the economic potential of alternative strategies for growing and marketing male offspring of organic dairy cattle in the Midwest. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Inverse free steering law for small satellite attitude control and power tracking with VSCMGs

NASA Astrophysics Data System (ADS)

Malik, M. S. I.; Asghar, Sajjad

2014-01-01

Recent developments in integrated power and attitude control systems (IPACSs) for small satellite, has opened a new dimension to more complex and demanding space missions. This paper presents a new inverse free steering approach for integrated power and attitude control systems using variable-speed single gimbal control moment gyroscope. The proposed inverse free steering law computes the VSCMG steering commands (gimbal rates and wheel accelerations) such that error signal (difference in command and output) in feedback loop is driven to zero. H∞ norm optimization approach is employed to synthesize the static matrix elements of steering law for a static state of VSCMG. Later these matrix elements are suitably made dynamic in order for the adaptation. In order to improve the performance of proposed steering law while passing through a singular state of CMG cluster (no torque output), the matrix element of steering law is suitably modified. Therefore, this steering law is capable of escaping internal singularities and using the full momentum capacity of CMG cluster. Finally, two numerical examples for a satellite in a low earth orbit are simulated to test the proposed steering law.

Soft rot erwiniae: from genes to genomes.

PubMed

Toth, Ian K; Bell, Kenneth S; Holeva, Maria C; Birch, Paul R J

2003-01-01

SUMMARY The soft rot erwiniae, Erwinia carotovora ssp. atroseptica (Eca), E. carotovora ssp. carotovora (Ecc) and E. chrysanthemi (Ech) are major bacterial pathogens of potato and other crops world-wide. We currently understand much about how these bacteria attack plants and protect themselves against plant defences. However, the processes underlying the establishment of infection, differences in host range and their ability to survive when not causing disease, largely remain a mystery. This review will focus on our current knowledge of pathogenesis in these organisms and discuss how modern genomic approaches, including complete genome sequencing of Eca and Ech, may open the door to a new understanding of the potential subtlety and complexity of soft rot erwiniae and their interactions with plants. The soft rot erwiniae are members of the Enterobacteriaceae, along with other plant pathogens such as Erwinia amylovora and human pathogens such as Escherichia coli, Salmonella spp. and Yersinia spp. Although the genus name Erwinia is most often used to describe the group, an alternative genus name Pectobacterium was recently proposed for the soft rot species. Ech mainly affects crops and other plants in tropical and subtropical regions and has a wide host range that includes potato and the important model host African violet (Saintpaulia ionantha). Ecc affects crops and other plants in subtropical and temperate regions and has probably the widest host range, which also includes potato. Eca, on the other hand, has a host range limited almost exclusively to potato in temperate regions only. Disease symptoms: Soft rot erwiniae cause general tissue maceration, termed soft rot disease, through the production of plant cell wall degrading enzymes. Environmental factors such as temperature, low oxygen concentration and free water play an essential role in disease development. On potato, and possibly other plants, disease symptoms may differ, e.g. blackleg disease is associated more with Eca and Ech than with Ecc. http://www.scri.sari.ac.uk/TiPP/Erwinia.htm, http://www.ahabs.wisc.edu:16080/ approximately pernalab/erwinia/index.htm, http://www.tigr.org/tdb/mdb/mdbinprogress.html, http://www.sanger.ac.uk/Projects/E_carotovora/.

Effect of post-ethanol extraction sorghum silage as a forage source in growing and finishing diets on steer performance, carcass characteristics, and nutrient digestibility.

PubMed

Blank, C P; Loy, D D; Hansen, S L

2017-07-01

Two experiments evaluated the use of post-ethanol extraction sorghum silage as an alternative forage source in feedlot diets. Seventy-two crossbred steers (397 kg [SD 23]) were used to evaluate growth and carcass characteristics. Steers were blocked by BW into pens of 6 steers and randomly assigned to growing diets containing 40% (DM basis) sorghum silage (SS; 57.6% NDF) or grass hay (CON; 63.3% NDF) for 56 d ( = 6 pens per treatment). Within each treatment, steers transitioned to dry-rolled corn-based finishing diets (fed for 56 d) containing 6% effective NDF contributed by the forage source, resulting in forage inclusions of 16% for SS and 13.1% for CON, where forage replaced corn. A subsample of steers ( = 12 per treatment) housed in pens equipped with GrowSafe bunks were used for determination of growing phase diet total tract digestibility. From d 28 to 42, steers received titanium dioxide at approximately 10 g∙steer∙d, and fecal samples were collected on d 41 and 42. Fecal and total mixed ration samples were dried and ground for analysis of DM, OM, NDF, ADF, CP, ether extract (EE), and starch. Data were analyzed with the MIXED procedure of SAS, with fixed effects of treatment and block for performance and carcass data or treatment for digestibility data; significance was determined at ≤ 0.05 and tendencies at ≤ 0.10. Growing phase DMI and ADG did not differ due to treatment ( ≥ 0.19); however, SS-fed steers had improved G:F compared with CON-fed steers ( = 0.04). Finishing period ADG and G:F did not differ ( ≥ 0.15) between treatments, despite SS-fed steers having lesser ( = 0.008) DMI than CON-fed steers. No differences in DMI, ADG, or G:F over the whole trial were noted between treatments ( ≥ 0.12) nor were any carcass traits affected ( ≥ 0.23). During the digestibility assessment period, DMI was less ( = 0.003) in SS-fed steers. Growing phase total tract apparent digestibility of DM and starch did not differ ( ≥ 0.19) due to treatment; however, OM digestibility tended to be greater ( = 0.09) in SS-fed steers. Steers fed SS had greater ( ≤ 0.03) digestibility of EE, CP, NDF, and hemicellulose than CON-fed steers. However, CON-fed steers had greater ( < 0.0001) ADF digestibility than SS-fed steers. These data suggest that postextraction sorghum silage can be effectively used in feedlot diets as an alternative forage source.

Static Force-Deflection Properties of Automobile Steering Components

DOT National Transportation Integrated Search

1987-06-01

This report provides the static force-deflection test results for 28 steering columns and 24 steering wheels used in domestic and import passener cars from model year 1975 to 1985. The steering columns and wheels tested include approzimately 90 perce...

Collective multipartite Einstein-Podolsky-Rosen steering: more secure optical networks.

PubMed

Wang, Meng; Gong, Qihuang; He, Qiongyi

2014-12-01

Collective multipartite Einstein-Podolsky-Rosen (EPR) steering is a type of quantum correlation shared among N parties, where the EPR paradox of one party can only be realized by performing local measurements on all the remaining N-1 parties. We formalize the collective tripartite steering in terms of local hidden state model and give the steering inequalities that act as signatures and suggest how to optimize collective tripartite steering in specific optical schemes. The special entangled states with property of collective multipartite steering may have potential applications in ultra-secure multiuser communication networks where the issue of trust is critical.

Effects of a Saccharomyces cerevisiae fermentation product in receiving diets of newly weaned beef steers II: Digestibility and response to a vaccination challenge.

PubMed

Deters, E L; Stokes, R S; Genther-Schroeder, O N; Hansen, S L

2018-06-15

Thirty-six newly weaned, crossbred beef steers (323 ± 12 kg; SD) from a single-source were used in a 56-d study to examine the effects of a Saccharomyces cerevisiae fermentation product (SCFP; Original XPC, Diamond V, Cedar Rapids, IA) on total tract nutrient digestibility and response to a vaccination challenge. Twelve d after arrival, steers were blocked by body weight (BW) and randomly assigned to treatments: SCFP at 0 (CON), 14 (SCFP14), or 28 (SCFP28) g·steer-1·d-1. Steers were fed via bunks that measured individual intake and received ear tags (CowManager, Select Sires, Plain City, OH) that recorded rumination and activity. Body weights were collected on d -1, 0, 14, 28, 42, 55, and 56. Titanium dioxide was fed as an indigestible marker to all steers from d 12 to 27, followed by consecutive d fecal samples, for determination of total tract nutrient digestibility. On d 34, steers received a Mannheimia haemolytica vaccination (One Shot, Zoetis, Kalamazoo, MI) to induce an acute phase protein (APP) response. Blood was collected from all steers on d 34 (prior to vaccination) and 3, 6, 9, 11, and 14 d post-vaccination. Data were analyzed using Proc Mixed of SAS (experimental unit = steer; n = 12/treatment); the model included the fixed effect of treatment and block and the random effect of steer. Blood measures, ear tag, and dry matter intake (DMI) data for the 15-d vaccination period were analyzed as repeated measures. Contrast statements (CON vs. SCFP14; SCFP14 vs. SCFP28) were used to compare treatment means. Digestibility of dry matter and organic matter was greater for SCFP14 vs. SCFP28 (P ≤ 0.03). Steers fed SCFP14 exhibited greater crude protein digestibility compared to CON (P < 0.01). Steers fed SCFP14 exhibited greater DMI for 15 d post-vaccination (P = 0.02) and greater ADG from d 28 to 56 (P = 0.05) vs. SCFP28-fed steers. Post-vaccination, steers fed SCFP14 spent less time ruminating per kg of dry matter, neutral detergent fiber (NDF), and physically effective NDF consumed than CON or SCFP28 (P ≤ 0.07). Serum IL-8 and haptoglobin concentrations tended to be lesser for steers fed SCFP14 vs. SCFP28 (P ≤ 0.08). Ceruloplasmin concentrations were lesser on d 14 post-vaccination for steers fed SCFP14 vs. CON or SCFP28 (treatment × d; P = 0.004); there were no differences on other sampling days due to treatment. Although no overall performance benefit was noted, steers fed SCFP14 responded better to a vaccination challenge vs. SCFP28-fed steers.

Ruminal acidosis challenge impact on ruminal temperature in feedlot cattle.

PubMed

Wahrmund, J L; Ronchesel, J R; Krehbiel, C R; Goad, C L; Trost, S M; Richards, C J

2012-08-01

The objective of this experiment was to determine if ruminal temperature rise coincides with pH reduction using an acidosis challenge model. Twelve ruminally cannulated steers (518 ± 28 kg BW) were administered ruminal temperature-monitoring devices that recorded temperature every 2 min. Steers were fed a 63% concentrate diet at 1.6% BW for 20 d before being randomly assigned to 1 of 3 acidosis challenge treatments: no dietary change (CON), one-half of daily DMI replaced with cracked corn (HALF), or all of daily DMI replaced with cracked corn (CORN). The challenge was initiated by ruminally dosing steers with their treatment diets. Ruminal pH and rectal temperatures (T(rec)) were recorded every 3 h for 72 h. All steers were offered CON diets at 24 and 48 h after challenge. Ruminal pH showed a treatment × day effect (P = 0.01). Ruminal pH of CORN steers was lower (P = 0.03) than that of HALF steers on d 1, was lower (P ≤ 0.004) than that of HALF and CON steers on d 2, and tended to be lower (P ≤ 0.10) than that of HALF and CON steers on d 3. Treatment did not affect (P ≥ 0.42) RecT. Ruminal temperature (T(rum)) showed a treatment · d(-1) · h(-1) after feeding interaction (P < 0.01). At 3 h after challenge, T(rum) of CORN and HALF steers was higher (P ≤ 0.01) than that of CON steers. On d 2, T(rum) of CORN steers was higher (P ≤ 0.03) than that of CON between 6 and 12 h after feeding. From 15 to 21 h after feeding on d 2, T(rum) of HALF steers was higher (P < 0.01) than that of CORN and CON steers. On d 3, at the time of feeding until 3 h later, T(rum) of CORN steers was lower (P ≤ 0.04) than that of all other steers. Rectal temperature was correlated (P ≤ 0.01) with T(rum) on all days for CON and CORN steers. Ruminal pH was negatively correlated (P ≤ 0.04) with T(rec) on d 2 and T(rum) on d 1 in CORN steers, and T(rum) was negatively correlated (P ≤ 0.02) with ruminal pH in HALF and CON steers on d 1 and 3, respectively. The amount of time above T(rum) of 39.0°C or 39.45°C was correlated (P ≤ 0.05) with the time spent below a ruminal pH of 5.5 in CORN steers; however, time above T(rum) of 39.0°C did not differ (P = 0.87) among treatments. Results indicate that there is a negative relationship between T(rum) and ruminal pH during an acidotic episode; therefore, T(rum) monitoring can detect a potential acidotic episode.

Electronic differential control of 2WD electric vehicle considering steering stability

NASA Astrophysics Data System (ADS)

Hua, Yiding; Jiang, Haobin; Geng, Guoqing

2017-03-01

Aiming at the steering wheel differential steering control technology of rear wheel independent driving electric wheel, considering the assisting effect of electronic differential control on vehicle steering, based on the high speed steering characteristic of electric wheel car, the electronic differential speed of auxiliary wheel steering is also studied. A yaw moment control strategy is applied to the vehicle at high speed. Based on the vehicle stability reference value, yaw rate is used to design the fuzzy controller to distribute the driving wheel torque. The simulation results show that the basic electronic differential speed function is realized based on the yaw moment control strategy, while the vehicle stability control is improved and the driving safety is enhanced. On the other hand, the torque control strategy can also assist steering of vehicle.

Quantum steerability: Characterization, quantification, superactivation, and unbounded amplification

NASA Astrophysics Data System (ADS)

Hsieh, Chung-Yun; Liang, Yeong-Cherng; Lee, Ray-Kuang

2016-12-01

Quantum steering, also called Einstein-Podolsky-Rosen steering, is the intriguing phenomenon associated with the ability of spatially separated observers to steer—by means of local measurements—the set of conditional quantum states accessible by a distant party. In the light of quantum information, all steerable quantum states are known to be resources for quantum information processing tasks. Here, via a quantity dubbed steering fraction, we derive a simple, but general criterion that allows one to identify quantum states that can exhibit quantum steering (without having to optimize over the measurements performed by each party), thus making an important step towards the characterization of steerable quantum states. The criterion, in turn, also provides upper bounds on the largest steering-inequality violation achievable by arbitrary finite-dimensional maximally entangled states. For the quantification of steerability, we prove that a strengthened version of the steering fraction is a convex steering monotone and demonstrate how it is related to two other steering monotones, namely, steerable weight and steering robustness. Using these tools, we further demonstrate the superactivation of steerability for a well-known family of entangled quantum states, i.e., we show how the steerability of certain entangled, but unsteerable quantum states can be recovered by allowing joint measurements on multiple copies of the same state. In particular, our approach allows one to explicitly construct a steering inequality to manifest this phenomenon. Finally, we prove that there exist examples of quantum states (including some which are unsteerable under projective measurements) whose steering-inequality violation can be arbitrarily amplified by allowing joint measurements on as little as three copies of the same state. For completeness, we also demonstrate how the largest steering-inequality violation can be used to bound the largest Bell-inequality violation and derive, analogously, a simple sufficient condition for Bell nonlocality from the latter.

A CMOS 0.18 μm 600 MHz clock multiplier PLL and a pseudo-LVDS driver for the high speed data transmission for the ALICE Inner Tracking System front-end chip

NASA Astrophysics Data System (ADS)

Lattuca, A.; Mazza, G.; Aglieri Rinella, G.; Cavicchioli, C.; Chanlek, N.; Collu, A.; Degerli, Y.; Dorokhov, A.; Flouzat, C.; Gajanana, D.; Gao, C.; Guilloux, F.; Hillemanns, H.; Hristozkov, S.; Junique, A.; Keil, M.; Kim, D.; Kofarago, M.; Kugathasan, T.; Kwon, Y.; Mager, M.; Sielewicz, K. Marek; Marin Tobon, C. Augusto; Marras, D.; Martinengo, P.; Mugnier, H.; Musa, L.; Pham, T. Hung; Puggioni, C.; Reidt, F.; Riedler, P.; Rousset, J.; Siddhanta, S.; Snoeys, W.; Song, M.; Usai, G.; Van Hoorne, J. Willem; Yang, P.

2016-01-01

This work presents the 600 MHz clock multiplier PLL and the pseudo-LVDS driver which are two essential components of the Data Transmission Unit (DTU), a fast serial link for the 1.2 Gb/s data transmission of the ALICE inner detector front-end chip (ALPIDE). The PLL multiplies the 40 MHz input clock in order to obtain the 600 MHz and the 200 MHz clock for a fast serializer which works in Double Data Rate mode. The outputs of the serializer feed the pseudo-LVDS driver inputs which transmits the data from the pixel chip to the patch panel with a limited number of signal lines. The driver drives a 5.3 m-6.5 m long differential transmission line by steering a maximum of 5 mA of current at the target speed. To overcome bandwidth limitations coming from the long cables the pre-emphasis can be applied to the output. Currents for the main and pre-emphasis driver can individually be adjusted using on-chip digital-to-analog converters. The circuits will be integrated in the pixel chip and are designed in the same 0.18 μm CMOS technology and will operate from the same 1.8 V supply. Design and test results of both circuits are presented.

Front and Back Movement Analysis of a Triangle-Structured Three-Wheeled Omnidirectional Mobile Robot by Varying the Angles between Two Selected Wheels

PubMed Central

Mohanraj, A. P.; Elango, A.; Reddy, Mutra Chanakya

2016-01-01

Omnidirectional robots can move in all directions without steering their wheels and it can rotate clockwise and counterclockwise with reference to their axis. In this paper, we focused only on front and back movement, to analyse the square- and triangle-structured omnidirectional robot movements. An omnidirectional mobile robot shows different performances with the different number of wheels and the omnidirectional mobile robot's chassis design. Research is going on in this field to improve the accurate movement capability of omnidirectional mobile robots. This paper presents a design of a unique device of Angle Variable Chassis (AVC) for linear movement analysis of a three-wheeled omnidirectional mobile robot (TWOMR), at various angles (θ) between the wheels. Basic mobility algorithm is developed by varying the angles between the two selected omnidirectional wheels in TWOMR. The experiment is carried out by varying the angles (θ = 30°, 45°, 60°, 90°, and 120°) between the two selected omniwheels and analysing the movement of TWOMR in forward direction and reverse direction on a smooth cement surface. Respectively, it is compared to itself for various angles (θ), to get its advantages and weaknesses. The conclusion of the paper provides effective movement of TWOMR at a particular angle (θ) and also the application of TWOMR in different situations. PMID:26981585

Front and Back Movement Analysis of a Triangle-Structured Three-Wheeled Omnidirectional Mobile Robot by Varying the Angles between Two Selected Wheels.

PubMed

Mohanraj, A P; Elango, A; Reddy, Mutra Chanakya

2016-01-01

Omnidirectional robots can move in all directions without steering their wheels and it can rotate clockwise and counterclockwise with reference to their axis. In this paper, we focused only on front and back movement, to analyse the square- and triangle-structured omnidirectional robot movements. An omnidirectional mobile robot shows different performances with the different number of wheels and the omnidirectional mobile robot's chassis design. Research is going on in this field to improve the accurate movement capability of omnidirectional mobile robots. This paper presents a design of a unique device of Angle Variable Chassis (AVC) for linear movement analysis of a three-wheeled omnidirectional mobile robot (TWOMR), at various angles (θ) between the wheels. Basic mobility algorithm is developed by varying the angles between the two selected omnidirectional wheels in TWOMR. The experiment is carried out by varying the angles (θ = 30°, 45°, 60°, 90°, and 120°) between the two selected omniwheels and analysing the movement of TWOMR in forward direction and reverse direction on a smooth cement surface. Respectively, it is compared to itself for various angles (θ), to get its advantages and weaknesses. The conclusion of the paper provides effective movement of TWOMR at a particular angle (θ) and also the application of TWOMR in different situations.

Impact of grazing dairy steers on winter rye (Secale cereale) versus winter wheat (Triticum aestivum) and effects on meat quality, fatty acid and amino acid profiles, and consumer acceptability of organic beef

PubMed Central

Phillips, Hannah N.; Delate, Kathleen; Turnbull, Robert

2017-01-01

Meat from Holstein and crossbred organic dairy steers finished on winter rye and winter wheat pastures was evaluated and compared for meat quality, fatty acid and amino acid profiles, and consumer acceptability. Two adjacent 4-ha plots were established with winter rye or winter wheat cover crops in September 2015 at the University of Minnesota West Central Research and Outreach Center (Morris, MN). During spring of 2015, 30 steers were assigned to one of three replicate breed groups at birth. Breed groups were comprised of: Holstein (HOL; n = 10), crossbreds comprised of Montbéliarde, Viking Red, and HOL (MVH; n = 10), and crossbreds comprised of Normande, Jersey, and Viking Red (NJV; n = 10). Dairy steers were maintained in their respective replicate breed group from three days of age until harvest. After weaning, steers were fed an organic total mixed ration of organic corn silage, alfalfa silage, corn, soybean meal, and minerals until spring 2016. Breed groups were randomly assigned to winter rye or winter wheat and rotationally grazed from spring until early summer of 2016. For statistical analysis, independent variables were fixed effects of breed, forage, and the interaction of breed and forage, with replicated group as a random effect. Specific contrast statements were used to compare HOL versus crossbred steers. Fat from crossbreds had 13% greater omega-3 fatty acids than HOL steers. Furthermore, the omega-6/3 ratio was 14% lower in fat from crossbreds than HOL steers. For consumer acceptability, steaks from steers grazed on winter wheat had greater overall liking than steers grazed on winter rye. Steak from crossbreeds had greater overall liking than HOL steers. The results suggest improvement in fatty acids and sensory attributes of beef from crossbred dairy steers compared to HOL steers, as well as those finished on winter wheat compared to winter rye. PMID:29099863

Impact of grazing dairy steers on winter rye (Secale cereale) versus winter wheat (Triticum aestivum) and effects on meat quality, fatty acid and amino acid profiles, and consumer acceptability of organic beef.

PubMed

Phillips, Hannah N; Heins, Bradley J; Delate, Kathleen; Turnbull, Robert

2017-01-01

Meat from Holstein and crossbred organic dairy steers finished on winter rye and winter wheat pastures was evaluated and compared for meat quality, fatty acid and amino acid profiles, and consumer acceptability. Two adjacent 4-ha plots were established with winter rye or winter wheat cover crops in September 2015 at the University of Minnesota West Central Research and Outreach Center (Morris, MN). During spring of 2015, 30 steers were assigned to one of three replicate breed groups at birth. Breed groups were comprised of: Holstein (HOL; n = 10), crossbreds comprised of Montbéliarde, Viking Red, and HOL (MVH; n = 10), and crossbreds comprised of Normande, Jersey, and Viking Red (NJV; n = 10). Dairy steers were maintained in their respective replicate breed group from three days of age until harvest. After weaning, steers were fed an organic total mixed ration of organic corn silage, alfalfa silage, corn, soybean meal, and minerals until spring 2016. Breed groups were randomly assigned to winter rye or winter wheat and rotationally grazed from spring until early summer of 2016. For statistical analysis, independent variables were fixed effects of breed, forage, and the interaction of breed and forage, with replicated group as a random effect. Specific contrast statements were used to compare HOL versus crossbred steers. Fat from crossbreds had 13% greater omega-3 fatty acids than HOL steers. Furthermore, the omega-6/3 ratio was 14% lower in fat from crossbreds than HOL steers. For consumer acceptability, steaks from steers grazed on winter wheat had greater overall liking than steers grazed on winter rye. Steak from crossbreeds had greater overall liking than HOL steers. The results suggest improvement in fatty acids and sensory attributes of beef from crossbred dairy steers compared to HOL steers, as well as those finished on winter wheat compared to winter rye.

46 CFR 169.251 - Steering apparatus.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Steering apparatus. 169.251 Section 169.251 Shipping... Inspection and Certification Inspections § 169.251 Steering apparatus. At each inspection for certification and periodic inspection the steering apparatus is inspected and operationally tested to determine that...

46 CFR 169.251 - Steering apparatus.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Steering apparatus. 169.251 Section 169.251 Shipping... Inspection and Certification Inspections § 169.251 Steering apparatus. At each inspection for certification and periodic inspection the steering apparatus is inspected and operationally tested to determine that...

All-Versus-Nothing Proof of Einstein-Podolsky-Rosen Steering

PubMed Central

Chen, Jing-Ling; Ye, Xiang-Jun; Wu, Chunfeng; Su, Hong-Yi; Cabello, Adán; Kwek, L. C.; Oh, C. H.

2013-01-01

Einstein-Podolsky-Rosen steering is a form of quantum nonlocality intermediate between entanglement and Bell nonlocality. Although Schrödinger already mooted the idea in 1935, steering still defies a complete understanding. In analogy to “all-versus-nothing” proofs of Bell nonlocality, here we present a proof of steering without inequalities rendering the detection of correlations leading to a violation of steering inequalities unnecessary. We show that, given any two-qubit entangled state, the existence of certain projective measurement by Alice so that Bob's normalized conditional states can be regarded as two different pure states provides a criterion for Alice-to-Bob steerability. A steering inequality equivalent to the all-versus-nothing proof is also obtained. Our result clearly demonstrates that there exist many quantum states which do not violate any previously known steering inequality but are indeed steerable. Our method offers advantages over the existing methods for experimentally testing steerability, and sheds new light on the asymmetric steering problem. PMID:23828242

Highly sensitive beam steering with plasmonic antenna

PubMed Central

Rui, Guanghao; Zhan, Qiwen

2014-01-01

In this work, we design and study a highly sensitive beam steering device that integrates a spiral plasmonic antenna with a subwavelength metallic waveguide. The short effective wavelength of the surface plasmon polaritons (SPPs) mode supported by the metallic waveguide is exploited to dramatically miniaturize the device and improve the sensitivity of the beam steering. Through introducing a tiny displacement of feed point with respect to the geometrical center of the spiral plasmonic antenna, the direction of the radiation can be steered at considerably high angles. Simulation results show that steering angles of 8°, 17° and 34° are obtainable for a displacement of 50 nm, 100 nm and 200 nm, respectively. Benefiting from the reduced device size and the shorter SPP wavelength, the beam steering sensitivity of the beam steering is improved by 10-fold compared with the case reported previously. This miniature plasmonic beam steering device may find many potential applications in quantum optical information processing and integrated photonic circuits. PMID:25091405

Chaos vibration of pinion and rack steering trapezoidal mechanism containing two clearances

NASA Astrophysics Data System (ADS)

Wei, Daogao; Wang, Yu; Jiang, Tong; Zheng, Sifa; Zhao, Wenjing; Pan, Zhijie

2017-08-01

The multi-clearances of breaking type steering trapezoidal mechanism joints influences vehicle steering stability. Hence, to ascertain the influence of clearance value on steering stability, this paper takes the steering mechanism of a certain vehicle type as a prototype that can be simplified into a planar six-bar linkage, then establishes the system dynamic differential equations after considering the two clearances of tie rods and the steering knuckle arms. The influence of the clearance parameters on the movement stability of the steering mechanism is studied using a numerical computation method. Results show that when the two clearances are equal, the planar movement of the tie rods changes from period-doubling to chaos as the clearances increase. When the two clearances are 0.25 mm and 1.5 mm respectively, the planar movements of the two side tie rods come into chaos, causing the steering stability to deteriorate. Moreover, with the increase of clearances, turning moment fluctuates more intensively and the peak value increases.

Modeling of Driver Steering Operations in Lateral Wind Disturbances toward Driver Assistance System

NASA Astrophysics Data System (ADS)

Kurata, Yoshinori; Wada, Takahiro; Kamiji, Norimasa; Doi, Shun'ichi

Disturbances decrease vehicle stability and increase driver's mental and physical workload. Especially unexpected disturbances such as lateral winds have severe effect on vehicle stability and driver's workload. This study aims at building a driver model of steering operations in lateral wind toward developing effective driver assistance system. First, the relationship between the driver's lateral motion and its reactive quick steering behavior is investigated using driving simulator with lateral 1dof motion. In the experiments, four different wind patterns are displayed by the simulator. As the results, strong correlation was found between the driver's head lateral jerk by the lateral disturbance and the angular acceleration of the steering wheel. Then, we build a mathematical model of driver's steering model from lateral disturbance input to steering torque of the reactive quick feed-forward steering based on the experimental results. Finally, validity of the proposed model is shown by comparing the steering torque of experimental results and that of simulation results.

Determination of tocopherols and sitosterols in seeds and nuts by QuEChERS-liquid chromatography.

PubMed

Delgado-Zamarreño, M Milagros; Fernández-Prieto, Cristina; Bustamante-Rangel, Myriam; Pérez-Martín, Lara

2016-02-01

In the present work a simple, reliable and affordable sample treatment method for the simultaneous analysis of tocopherols and free phytosterols in nuts was developed. Analyte extraction was carried out using the QuEChERS methodology and analyte separation and detection were accomplished using HPLC-DAD. The use of this methodology for the extraction of natural occurring substances provides advantages such as speed, simplicity and ease of use. The parameters evaluated for the validation of the method developed included the linearity of the calibration plots, the detection and quantification limits, repeatability, reproducibility and recovery. The proposed method was successfully applied to the analysis of tocopherols and free phytosterols in samples of almonds, cashew nuts, hazelnuts, peanuts, tiger nuts, sun flower seeds and pistachios. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterising the Atmospheres of Transiting Planets with a Dedicated Space Telescope

NASA Astrophysics Data System (ADS)

Tessenyi, M.; Ollivier, M.; Tinetti, G.; Beaulieu, J. P.; Coudé du Foresto, V.; Encrenaz, T.; Micela, G.; Swinyard, B.; Ribas, I.; Aylward, A.; Tennyson, J.; Swain, M. R.; Sozzetti, A.; Vasisht, G.; Deroo, P.

2011-10-01

Transiting super-Earths orbiting M dwarfs are excellent targets for the prospect of studying potentially habitable extrasolar planets. While most of the currently known Exoplanets are of the Hot Jupiter and Neptune type, attention is now turning to these super- Earths. Two recent examples are GJ 1214b, found by Charbonneau et al. in 2009, and Cancri 55 e, found by Winn et al. in 2011. These candidates offer the opportunity of obtaining spectral signatures of their atmospheres in transiting scenarios, via data obtained by ground based and space observatories, compared to simulated climate scenarios. With the recent selection of the Exoplanet Characterisation Observatory (EChO) mission by ESA for further studies, I present observational strategies and time requirements for a range of targets characterisable by EChO, with a view to super-Earths orbiting M dwarfs.

Reply to comments on "Volatile methylsiloxanes in personal care products - Using QuEChERS as a "green" analytical approach" published in Talanta 174 (2017) 156-157.

PubMed

Capela, Daniela; Homem, Vera; Alves, Arminda; Santos, Lúcia

2018-03-01

Recently, Pierre Germain from CES - Silicon Europe published a comment on the paper "Volatile methylsiloxanes in personal care products - Using QuEChERS as a "green" analytical approach", raising concerns that the artefacts employed in the analysis of cyclic volatile methylsiloxanes (cVMS) were not adequately controlled, while using this example as an opportunity to emphasize the difficulties associated with siloxanes analyses in complex matrices such as personal care products (PCPs). We are now addressing these concerns and conveying some clarifications regarding the experiments performed to validate the analytical method adequately. Those details were not included in the original publication because the objective was the quantification of VMS in several PCPs. Copyright © 2017 Elsevier B.V. All rights reserved.

Understanding rotation profile structures in ECH-heated plasmas using nonlinear gyrokinetic simulations

NASA Astrophysics Data System (ADS)

Wang, Weixing; Brian, B.; Ethier, S.; Chen, J.; Startsev, E.; Diamond, P. H.; Lu, Z.

2015-11-01

A non-diffusive momentum flux connecting edge momentum sources/sinks and core plasma flow is required to establish the off-axis peaked ion rotation profile typically observed in ECH-heated DIII-D plasmas without explicit external momentum input. The understanding of the formation of such profile structures provides an outstanding opportunity to test the physics of turbulence driving intrinsic rotation, and validate first-principles-based gyrokinetic simulation models. Nonlinear, global gyrokinetic simulations of DIII-D ECH plasmas indicate a substantial ITG fluctuation-induced residual stress generated around the region of peaked toroidal rotation, along with a diffusive momentum flux. The residual stress profile shows an anti-gradient, dipole structure, which is critical for accounting for the formation of the peaked rotation profile. It is showed that both turbulence intensity gradient and zonal flow ExB shear contribute to the generation of k// asymmetry needed for residual stress generation. By balancing the simulated residual stress and the momentum diffusion, a rotation profile is calculated. In general, the radial structure of core rotation profile is largely determined by the residual stress profile, while the amplitude of core rotation depends on the edge toroidal rotation velocity, which is determined by edge physics and used as a boundary condition in our model. The calculated core rotation profile is consistent with the experimental measurements. Also discussed is the modification of turbulence-generated Reynolds stress on poloidal rotation in those plasmas. Work supported by U.S. DOE Contract DE-AC02-09-CH11466.

Impact of echinocandin on prognosis of proven invasive candidiasis in ICU: A post-hoc causal inference model using the AmarCAND2 study.

PubMed

Bailly, Sébastien; Leroy, Olivier; Azoulay, Elie; Montravers, Philippe; Constantin, Jean-Michel; Dupont, Hervé; Guillemot, Didier; Lortholary, Olivier; Mira, Jean-Paul; Perrigault, Pierre-François; Gangneux, Jean-Pierre; Timsit, Jean-François

2017-04-01

guidelines recommend first-line systemic antifungal therapy (SAT) with echinocandins in invasive candidiasis (IC), especially in critically ill patients. This study aimed at assessing the impact of echinocandins compared to azoles as initial SAT on the 28-day prognosis in adult ICU patients. From the prospective multicenter AmarCAND2 cohort (835 patients), we selected those with documented IC and treated with echinocandins (ECH) or azoles (AZO). The average causal effect of echinocandins on 28-day mortality was assessed using an inverse probability of treatment weight (IPTW) estimator. 397 patients were selected, treated with echinocandins (242 patients, 61%) or azoles (155 patients, 39%); septic shock: 179 patients (45%). The median SAPSII was higher in the ECH group (48 [35; 62] vs. 43 [31; 58], p = 0.01). Crude mortality was 34% (ECH group) vs. 25% (AZO group). After adjustment on baseline confounders, no significant association emerged between initial SAT with echinocandins and 28-day mortality (HR: 0.95; 95% CI: [0.60; 1.49]; p = 0.82). However, echinocandin tended to benefit patients with septic shock (HR: 0.46 [0.19; 1.07]; p = 0.07). Patients who received echinocandins were more severely ill. Echinocandin use was associated with a non-significant 7% decrease of 28-day mortality and a trend to a beneficial effect for patient with septic shock. Copyright © 2017 The British Infection Association. Published by Elsevier Ltd. All rights reserved.

Enoyl-CoA hydratase mediates polyhydroxyalkanoate mobilization in Haloferax mediterranei

PubMed Central

Liu, Guiming; Cai, Shuangfeng; Hou, Jing; Zhao, Dahe; Han, Jing; Zhou, Jian; Xiang, Hua

2016-01-01

Although polyhydroxyalkanoate (PHA) accumulation and mobilization are one of the most general mechanisms for haloarchaea to adapt to the hypersaline environments with changeable carbon sources, the PHA mobilization pathways are still not clear for any haloarchaea. In this study, the functions of five putative (R)-specific enoyl-CoA hydratases (R-ECHs) in Haloferax mediterranei, named PhaJ1 to PhaJ5, respectively, were thoroughly investigated. Through gene deletion and complementation, we demonstrated that only certain of these ECHs had a slight contribution to poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) biosynthesis. But significantly, PhaJ1, the only R-ECH that is associated with PHA granules, was shown to be involved in PHA mobilization in this haloarchaeon. PhaJ1 catalyzes the dehydration of (R)-3-hydroxyacyl-CoA, the common product of PHA degradation, to enoyl-CoA, the intermediate of the β-oxidation cycle, thus could link PHA mobilization to β-oxidation pathway in H. mediterranei. This linkage was further indicated from the up-regulation of the key genes of β-oxidation under the PHA mobilization condition, as well as the obvious inhibition of PHA degradation upon inhibition of the β-oxidation pathway. Interestingly, 96% of phaJ-containing haloarchaeal species possess both phaC (encoding PHA synthase) and the full set genes of β-oxidation, implying that the mobilization of carbon storage in PHA through the β-oxidation cycle would be general in haloarchaea. PMID:27052994

Enoyl-CoA hydratase mediates polyhydroxyalkanoate mobilization in Haloferax mediterranei.

PubMed

Liu, Guiming; Cai, Shuangfeng; Hou, Jing; Zhao, Dahe; Han, Jing; Zhou, Jian; Xiang, Hua

2016-04-07

Although polyhydroxyalkanoate (PHA) accumulation and mobilization are one of the most general mechanisms for haloarchaea to adapt to the hypersaline environments with changeable carbon sources, the PHA mobilization pathways are still not clear for any haloarchaea. In this study, the functions of five putative (R)-specific enoyl-CoA hydratases (R-ECHs) in Haloferax mediterranei, named PhaJ1 to PhaJ5, respectively, were thoroughly investigated. Through gene deletion and complementation, we demonstrated that only certain of these ECHs had a slight contribution to poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) biosynthesis. But significantly, PhaJ1, the only R-ECH that is associated with PHA granules, was shown to be involved in PHA mobilization in this haloarchaeon. PhaJ1 catalyzes the dehydration of (R)-3-hydroxyacyl-CoA, the common product of PHA degradation, to enoyl-CoA, the intermediate of the β-oxidation cycle, thus could link PHA mobilization to β-oxidation pathway in H. mediterranei. This linkage was further indicated from the up-regulation of the key genes of β-oxidation under the PHA mobilization condition, as well as the obvious inhibition of PHA degradation upon inhibition of the β-oxidation pathway. Interestingly, 96% of phaJ-containing haloarchaeal species possess both phaC (encoding PHA synthase) and the full set genes of β-oxidation, implying that the mobilization of carbon storage in PHA through the β-oxidation cycle would be general in haloarchaea.

Recent Modifications and Validation of QuEChERS-dSPE Coupled to LC-MS and GC-MS Instruments for Determination of Pesticide/Agrochemical Residues in Fruits and Vegetables: Review.

PubMed

Lawal, Abubakar; Wong, Richard Chee Seng; Tan, Guan Huat; Abdulra'uf, Lukman Bola; Alsharif, Ali Mohamed Ali

2018-04-21

Fruits and vegetables constitute a major type of food consumed daily apart from whole grains. Unfortunately, the residual deposits of pesticides in these products are becoming a major health concern for human consumption. Consequently, the outcome of the long-term accumulation of pesticide residues has posed many health issues to both humans and animals in the environment. However, the residues have previously been determined using conventionally known techniques, which include liquid-liquid extraction, solid-phase extraction (SPE) and the recently used liquid-phase microextraction techniques. Despite the positive technological effects of these methods, their limitations include; time-consuming, operational difficulty, use of toxic organic solvents, low selective property and expensive extraction setups, with shorter lifespan of instrumental performances. Thus, the potential and maximum use of these methods for pesticides residue determination has resulted in the urgent need for better techniques that will overcome the highlighted drawbacks. Alternatively, attention has been drawn recently towards the use of quick, easy, cheap, effective, rugged and safe technique (QuEChERS) coupled with dispersive solid-phase extraction (dSPE) to overcome the setback challenges experienced by the previous technologies. Conclusively, the reviewed QuEChERS-dSPE techniques and the recent cleanup modifications justifiably prove to be reliable for routine determination and monitoring the concentration levels of pesticide residues using advanced instruments such as high-performance liquid chromatography, liquid chromatography-mass spectrometry and gas chromatography-mass spectrometry.

The fate of spirotetramat and dissipation metabolites in Apiaceae and Brassicaceae leaf-root and soil system under greenhouse conditions estimated by modified QuEChERS/LC-MS/MS.

PubMed

Łozowicka, Bożena; Mojsak, Patrycja; Kaczyński, Piotr; Konecki, Rafał; Borusiewicz, Andrzej

2017-12-15

The aim of this study was to investigate the dissipation of spirotetramat and its four metabolites (B-enol, B-keto, B-mono and B-glu) in different parts of vegetables belong to the minor crops (Appiacea and Brassicaceae) and soil from cultivation. The challenge of this study was to apply an optimized clean up step in QuEChERS to obtain one universal sorbent for different complex matrices like leaves with high levels of pigments, roots containing acids, sugars, polyphenolls and pigments and soil with organic ingredients. Eight commercial (Florisil, neutral alumina, GCB, PSA, C18, diatomaceous earth, VERDE and ChloroFiltr) and one organic (Chitosan) sorbents were tested. A modified clean up step in QuEChERS methodology was used for analysis. The dissipation of spirotetramat and its metabolites was described according to a first-order (FO) kinetics equation with R 2 between 0.9055 and 0.9838. The results showed that the time after 50% (DT 50 ) of the substance degraded was different for soil, roots and leaves, and amounted to 0.2day, 2.8-2.9days and 2.1-2.4days, respectively. The terminal residues of spiroteramat (expressed as the sum of spirotetramat, B-enol, B-glu, B-keto and B-mono) were much lower than the MRLs. Copyright © 2017 Elsevier B.V. All rights reserved.

Electrodeposition of palladium and reduced graphene oxide nanocomposites on foam-nickel electrode for electrocatalytic hydrodechlorination of 4-chlorophenol.

PubMed

Liu, Yong; Liu, Lan; Shan, Jun; Zhang, Jingdong

2015-06-15

A high-performance palladium (Pd) and reduced graphene oxide (RGO) composite electrode was prepared on foam-nickel (foam-Ni) via two-step electrodeposition processes. The scanning electron microscopic (SEM) observation showed that the obtained Pd/RGO/foam-Ni composite electrode displayed a uniform and compact morphology. The X-ray diffraction (XRD) and X-ray photoelectron spectroscopic (XPS) analysis confirmed the successful deposition of Pd and RGO on nickel substrate. The cyclic voltammetric (CV) measurements indicated that the presence of RGO greatly enhanced the active surface area of Pd particles deposited on foam-Ni. The as-deposited Pd/RGO/foam-Ni electrode was applied to electrocatalytic hydrodechlorination (ECH) of 4-chlorophenol (4-CP). Various factors influencing the dechlorination of 4-CP such as dechlorination current, initial concentration of 4-CP, Na2SO4 concentration and initial pH were systematically investigated. The thermodynamic analysis showed that the dechlorination reaction of 4-CP at different temperatures followed the first-order kinetics and the activation energy for 4-CP dechlorination on Pd/RGO/foam-Ni electrode was calculated to be 51.96 kJ mol(-1). Under the optimum conditions, the dechlorination efficiency of 4-CP could reach 100% after 60-min ECH treatment. Moreover, the prepared Pd/RGO/foam-Ni composite electrode showed good stability for recycling utilization in ECH of 4-CP. Copyright © 2015 Elsevier B.V. All rights reserved.

Pesticide analysis in teas and chamomile by liquid chromatography and gas chromatography tandem mass spectrometry using a modified QuEChERS method: validation and pilot survey in real samples.

PubMed

Lozano, Ana; Rajski, Łukasz; Belmonte-Valles, Noelia; Uclés, Ana; Uclés, Samanta; Mezcua, Milagros; Fernández-Alba, Amadeo R

2012-12-14

This paper presents the validation of a modified QuEChERS method in four matrices - green tea, red tea, black tea and chamomile. The experiments were carried out using blank samples spiked with a solution of 86 pesticides (insecticides, fungicides and herbicides) at four levels - 10, 25, 50 and 100 μg/kg. The samples were extracted according to the citrate QuEChERS protocol; however, to reduce the amount of coextracted matrix compounds, calcium chloride was employed instead of magnesium sulphate in the clean-up step. The samples were analysed by LC-MS/MS and GC-MS/MS. Included in the scope of validation were: recovery, linearity, matrix effects, limits of detection and quantitation as well as intra-day and inter-day precision. The validated method was used in a real sample survey carried out on 75 samples purchased in ten different countries. In all matrices, recoveries of the majority of compounds were in the 70-120% range and were characterised by precision lower than 20%. In 85% of pesticide/matrix combinations the analytes can be detected quantitatively by the proposed method at the European Union Maximum Residue Level. The analysis of the real samples revealed that large number of teas and chamomiles sold in the European Union contain pesticides whose usage is not approved and also pesticides in concentrations above the EU MRLs. Copyright © 2012 Elsevier B.V. All rights reserved.

Evaluating the accuracy of soil water sensors for irrigation scheduling to conserve freshwater

NASA Astrophysics Data System (ADS)

Ganjegunte, Girisha K.; Sheng, Zhuping; Clark, John A.

2012-06-01

In the Trans-Pecos area, pecan [ Carya illinoinensis (Wangenh) C. Koch] is a major irrigated cash crop. Pecan trees require large amounts of water for their growth and flood (border) irrigation is the most common method of irrigation. Pecan crop is often over irrigated using traditional method of irrigation scheduling by counting number of calendar days since the previous irrigation. Studies in other pecan growing areas have shown that the water use efficiency can be improved significantly and precious freshwater can be saved by scheduling irrigation based on soil moisture conditions. This study evaluated the accuracy of three recent low cost soil water sensors (ECH2O-5TE, Watermark 200SS and Tensiometer model R) to monitor volumetric soil water content (θv) to develop improved irrigation scheduling in a mature pecan orchard in El Paso, Texas. Results indicated that while all three sensors were successful in following the general trends of soil moisture conditions during the growing season, actual measurements differed significantly. Statistical analyses of results indicated that Tensiometer provided relatively accurate soil moisture data than ECH2O-5TE and Watermark without site-specific calibration. While ECH2O-5TE overestimated the soil water content, Watermark and Tensiometer underestimated. Results of this study suggested poor accuracy of all three sensors if factory calibration and reported soil water retention curve for study site soil texture were used. This indicated that sensors needed site-specific calibration to improve their accuracy in estimating soil water content data.

Roles of HynAB and Ech, the Only Two Hydrogenases Found in the Model Sulfate Reducer Desulfovibrio gigas

PubMed Central

Morais-Silva, Fabio O.; Santos, Catia I.; Rodrigues, Rute

2013-01-01

Sulfate-reducing bacteria are characterized by a high number of hydrogenases, which have been proposed to contribute to the overall energy metabolism of the cell, but exactly in what role is not clear. Desulfovibrio spp. can produce or consume H2 when growing on organic or inorganic substrates in the presence or absence of sulfate. Because of the presence of only two hydrogenases encoded in its genome, the periplasmic HynAB and cytoplasmic Ech hydrogenases, Desulfovibrio gigas is an excellent model organism for investigation of the specific function of each of these enzymes during growth. In this study, we analyzed the physiological response to the deletion of the genes that encode the two hydrogenases in D. gigas, through the generation of ΔechBC and ΔhynAB single mutant strains. These strains were analyzed for the ability to grow on different substrates, such as lactate, pyruvate, and hydrogen, under respiratory and fermentative conditions. Furthermore, the expression of both hydrogenase genes in the three strains studied was assessed through quantitative reverse transcription-PCR. The results demonstrate that neither hydrogenase is essential for growth on lactate-sulfate, indicating that hydrogen cycling is not indispensable. In addition, the periplasmic HynAB enzyme has a bifunctional activity and is required for growth on H2 or by fermentation of pyruvate. Therefore, this enzyme seems to play a dominant role in D. gigas hydrogen metabolism. PMID:23974026

The effect of electron cyclotron heating on density fluctuations at ion and electron scales in ITER baseline scenario discharges on the DIII-D tokamak

NASA Astrophysics Data System (ADS)

Marinoni, A.; Pinsker, R. I.; Porkolab, M.; Rost, J. C.; Davis, E. M.; Burrell, K. H.; Candy, J.; Staebler, G. M.; Grierson, B. A.; McKee, G. R.; Rhodes, T. L.; The DIII-D Team

2017-12-01

Experiments simulating the ITER baseline scenario on the DIII-D tokamak show that torque-free pure electron heating, when coupled to plasmas subject to a net co-current beam torque, affects density fluctuations at electron scales on a sub-confinement time scale, whereas fluctuations at ion scales change only after profiles have evolved to a new stationary state. Modifications to the density fluctuations measured by the phase contrast imaging diagnostic (PCI) are assessed by analyzing the time evolution following the switch-off of electron cyclotron heating (ECH), thus going from mixed beam/ECH to pure neutral beam heating at fixed βN . Within 20 ms after turning off ECH, the intensity of fluctuations is observed to increase at frequencies higher than 200 kHz in contrast, fluctuations at lower frequency are seen to decrease in intensity on a longer time scale, after other equilibrium quantities have evolved. Non-linear gyro-kinetic modeling at ion and electron scales scales suggest that, while the low frequency response of the diagnostic is consistent with the dominant ITG modes being weakened by the slow-time increase in flow shear, the high frequency response is due to prompt changes to the electron temperature profile that enhance electron modes and generate a larger heat flux and an inward particle pinch. These results suggest that electron heated regimes in ITER will feature multi-scale fluctuations that might affect fusion performance via modifications to profiles.

Electrochemical red-ox therapy of prostate cancer in nude mice.

PubMed

Cury, Fabio L; Bhindi, Bimal; Rocha, Joice; Scarlata, Eleonora; El Jurdi, Katia; Ladouceur, Michel; Beauregard, Stéphane; Vijh, Ashok K; Taguchi, Yosh; Chevalier, Simone

2015-08-01

Minimally invasive therapies are increasingly in demand for organ-confined prostate tumors. Electrochemical therapy (EChT) is attractive, as it relies on locally-induced reduction-oxidation reactions to kill tumor cells. Its efficacy for prostate cancer was assessed in human PC-3 and LNCaP tumor xenografts growing subcutaneously in nude mice (n = 80) by applying 2 Stainless Steel vs. 4 Platinum-Iridium (Pt-Ir) electrodes to deliver current densities of 10 to 35 mA/cm(2) for 30 or 60 min. The procedure was uneventful in 90% of mice. No difference in tumor vs. body temperature was observed. Changes at electrode-tumor junctions were immediate, with dryness and acidity (pH2-3) at the anode and oedema and alkalinity (pH10-12) at the cathode. This was accompanied by cellular alterations, found more pronounced at the cathode. Such acidic and alkaline conditions were cytotoxic in vitro and dissolved cells at pH>10. In mice, tumor destruction was extensive by 24h with almost undetectable blood prostate specific antigen (LNCaP model) and covered the whole tumor surface by 4 days. EChT was most efficient at 25-30 mA/cm(2) for 60 min, yielding the longest recurrence-free survival and higher cure rates, especially with 4 Pt-Ir electrodes. EChT is a promising option to optimize for organ-confined prostate tumors. Copyright © 2015 Elsevier B.V. All rights reserved.

Wave-Particle Interactions Involving Correlated Electron Bursts and Whistler Chorus in Earth's Radiation Belts

NASA Astrophysics Data System (ADS)

Echterling, N.; Schriver, D.; Roeder, J. L.; Fennell, J. F.

2017-12-01

During the recovery phase of substorm plasma injections, the Van Allen Probes commonly observe events of quasi-periodic energetic electron bursts correlating with simultaneously detected upper-band, whistler-mode chorus emissions. These electron bursts exhibit narrow ranges of pitch angles (75-80° and 100-105°) and energies (20-40 keV). Electron cyclotron harmonic (ECH) emissions are also commonly detected, but typically do not display correlation with the electron bursts. To examine sources of free energy and the generation of these wave emissions, an observed electron velocity distribution on January 13, 2013 is used as the starting condition for a particle in cell (PIC) simulation. Effects of temperature anisotropy (perpendicular temperature greater than parallel temperature), the presence of a loss cone and a cold electron population on the generation of whistler and ECH waves are examined to understand wave generation and nonlinear interactions with the particle population. These nonlinear interactions produce energy diffusion along with strong pitch angle scattering into the loss cone on the order of milliseconds, which is faster than a typical bounce period of seconds. To examine the quasi-periodic nature of the electron bursts, a loss-cone recycling technique is implemented to model the effects of the periodic emptying of the loss cone and electron injection on the growth of whistler and ECH waves. The results of the simulations are compared to the Van Allen Probe observations to determine electron acceleration, heating and transport in Earth's radiation belts due to wave-particle interactions.

Impacts to the chest of PMHSs - Influence of impact location and load distribution on chest response.

PubMed

Holmqvist, Kristian; Svensson, Mats Y; Davidsson, Johan; Gutsche, Andreas; Tomasch, Ernst; Darok, Mario; Ravnik, Dean

2016-02-01

The chest response of the human body has been studied for several load conditions, but is not well known in the case of steering wheel rim-to-chest impact in heavy goods vehicle frontal collisions. The aim of this study was to determine the response of the human chest in a set of simulated steering wheel impacts. PMHS tests were carried out and analysed. The steering wheel load pattern was represented by a rigid pendulum with a straight bar-shaped front. A crash test dummy chest calibration pendulum was utilised for comparison. In this study, a set of rigid bar impacts were directed at various heights of the chest, spanning approximately 120mm around the fourth intercostal space. The impact energy was set below a level estimated to cause rib fracture. The analysed results consist of responses, evaluated with respect to differences in the impacting shape and impact heights on compression and viscous criteria chest injury responses. The results showed that the bar impacts consistently produced lesser scaled chest compressions than the hub; the Middle bar responses were around 90% of the hub responses. A superior bar impact provided lesser chest compression; the average response was 86% of the Middle bar response. For inferior bar impacts, the chest compression response was 116% of the chest compression in the middle. The damping properties of the chest caused the compression to decrease in the high speed bar impacts to 88% of that in low speed impacts. From the analysis it could be concluded that the bar impact shape provides lower chest criteria responses compared to the hub. Further, the bar responses are dependent on the impact location of the chest. Inertial and viscous effects of the upper body affect the responses. The results can be used to assess the responses of human substitutes such as anthropomorphic test devices and finite element human body models, which will benefit the development process of heavy goods vehicle safety systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experimental verification of steerability via geometric Bell-like inequalities

NASA Astrophysics Data System (ADS)

Li, Jian; Wang, Cen-Yang; Liu, Tong-Jun; Wang, Qin

2018-03-01

Quantum steering is one form of quantum correlations interpolating between entanglement and Bell nonlocality, which in some cases can be detected by various steering inequalities. Recently, a remarkable and useful steerability criterion via geometric Bell-like inequalities was established [M. Zukowski, A. Dutta, and Z. Yin, Phys. Rev. A 91, 032107 (2015), 10.1103/PhysRevA.91.032107]. We report an experimental investigation of this steering criterion and verify the geometric Bell-like steering inequality experimentally by using of the Werner states. The results demonstrate that the geometric Bell-like steering inequality is a convenient tool to detect quantum steering both theoretically and practically.

Experimental test of single-system steering and application to quantum communication

NASA Astrophysics Data System (ADS)

Liu, Zhao-Di; Sun, Yong-Nan; Cheng, Ze-Di; Xu, Xiao-Ye; Zhou, Zong-Quan; Chen, Geng; Li, Chuan-Feng; Guo, Guang-Can

2017-02-01

Einstein-Podolsky-Rosen (EPR) steering describes the ability to steer remotely quantum states of an entangled pair by measuring locally one of its particles. Here we report on an experimental demonstration of single-system steering. The application to quantum communication is also investigated. Single-system steering refers to steering of a single d -dimensional quantum system that can be used in a unifying picture to certify the reliability of tasks employed in both quantum communication and quantum computation. In our experiment, high-dimensional quantum states are implemented by encoding polarization and orbital angular momentum of photons with dimensionality of up to 12.

Method for controlling a vehicle with two or more independently steered wheels

DOEpatents

Reister, D.B.; Unseren, M.A.

1995-03-28

A method is described for independently controlling each steerable drive wheel of a vehicle with two or more such wheels. An instantaneous center of rotation target and a tangential velocity target are inputs to a wheel target system which sends the velocity target and a steering angle target for each drive wheel to a pseudo-velocity target system. The pseudo-velocity target system determines a pseudo-velocity target which is compared to a current pseudo-velocity to determine a pseudo-velocity error. The steering angle targets and the steering angles are inputs to a steering angle control system which outputs to the steering angle encoders, which measure the steering angles. The pseudo-velocity error, the rate of change of the pseudo-velocity error, and the wheel slip between each pair of drive wheels are used to calculate intermediate control variables which, along with the steering angle targets are used to calculate the torque to be applied at each wheel. The current distance traveled for each wheel is then calculated. The current wheel velocities and steering angle targets are used to calculate the cumulative and instantaneous wheel slip and the current pseudo-velocity. 6 figures.

Optimized detection of steering via linear criteria for arbitrary-dimensional states

NASA Astrophysics Data System (ADS)

Zheng, Yu-Lin; Zhen, Yi-Zheng; Cao, Wen-Fei; Li, Li; Chen, Zeng-Bing; Liu, Nai-Le; Chen, Kai

2017-03-01

Einstein-Podolsky-Rosen (EPR) steering, as a new form of nonlocality, stands between entanglement and Bell nonlocality, implying promising applications for quantum information tasks. The problem of detecting EPR steering plays an important role in characterization of quantum nonlocality. Despite some significant progress, one still faces a practical issue: how to detect EPR steering in an experimentally friendly fashion. Resorting to an EPR steering inequality, one is required to apply a strategy as efficiently as possible for any selected measurement settings on the two subsystems, one of which may not be trusted. Inspired by the recent powerful linear criteria proposed by Saunders et al. [D. J. Saunders, S. J. Jones, H. M. Wiseman, and G. J. Pryde, Nat. Phys. 6, 845 (2010)., 10.1038/nphys1766], we present an optimized method of certifying steering for an arbitrary-dimensional state in a cost-effective manner. We provide a practical way to signify steering via only a few settings to optimally violate the steering inequality. Our method leads to steering detections in a highly efficient way, and can be performed with any number of settings, for an arbitrary bipartite mixed state, which can reduce experimental overheads significantly.

Gaussian quantum steering and its asymmetry in curved spacetime

NASA Astrophysics Data System (ADS)

Wang, Jieci; Cao, Haixin; Jing, Jiliang; Fan, Heng

2016-06-01

We study Gaussian quantum steering and its asymmetry in the background of a Schwarzschild black hole. We present a Gaussian channel description of quantum state evolution under the influence of Hawking radiation. We find that thermal noise introduced by the Hawking effect will destroy the steerability between an inertial observer Alice and an accelerated observer Bob who hovers outside the event horizon, while it generates steerability between Bob and a hypothetical observer anti-Bob inside the event horizon. Unlike entanglement behaviors in curved spacetime, here the steering from Alice to Bob suffers from a "sudden death" and the steering from anti-Bob to Bob experiences a "sudden birth" with increasing Hawking temperature. We also find that the Gaussian steering is always asymmetric and the maximum steering asymmetry cannot exceed ln 2 , which means the state never evolves to an extremal asymmetry state. Furthermore, we obtain the parameter settings that maximize steering asymmetry and find that (i) s =arccosh cosh/2r 1 -sinh2r is the critical point of steering asymmetry and (ii) the attainment of maximal steering asymmetry indicates the transition between one-way steerability and both-way steerability for the two-mode Gaussian state under the influence of Hawking radiation.

A theoretical model of speed-dependent steering torque for rolling tyres

NASA Astrophysics Data System (ADS)

Wei, Yintao; Oertel, Christian; Liu, Yahui; Li, Xuebing

2016-04-01

It is well known that the tyre steering torque is highly dependent on the tyre rolling speed. In limited cases, i.e. parking manoeuvre, the steering torque approaches the maximum. With the increasing tyre speed, the steering torque decreased rapidly. Accurate modelling of the speed-dependent behaviour for the tyre steering torque is a key factor to calibrate the electric power steering (EPS) system and tune the handling performance of vehicles. However, no satisfactory theoretical model can be found in the existing literature to explain this phenomenon. This paper proposes a new theoretical framework to model this important tyre behaviour, which includes three key factors: (1) tyre three-dimensional transient rolling kinematics with turn-slip; (2) dynamical force and moment generation; and (3) the mixed Lagrange-Euler method for contact deformation solving. A nonlinear finite-element code has been developed to implement the proposed approach. It can be found that the main mechanism for the speed-dependent steering torque is due to turn-slip-related kinematics. This paper provides a theory to explain the complex mechanism of the tyre steering torque generation, which helps to understand the speed-dependent tyre steering torque, tyre road feeling and EPS calibration.

View aft of compartment D23, aft steering station; note steering ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View aft of compartment D-23, aft steering station; note steering unit with crosshead and shaft bearing supports. Note framing supports for armored protective deck at top of photo. (p60) - USS Olympia, Penn's Landing, 211 South Columbus Boulevard, Philadelphia, Philadelphia County, PA

75 FR 45159 - Delphi Steering Currently Known as Nexteer Automotive Including On-Site Leased Workers From Acro...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-02

..., Inc., Continental, Inc., Dynamic Corp., G-Tech Professional Staffing, Inc., Globaledgetechnologies... Corporation, Aerotek, Inc., Continental, Inc., Dynamic Corp., G-Tech Professional Staffing, Inc., Globaledge... steering systems and components such as steering columns, gears, pumps and electronic power steering...

Driver behavior following an automatic steering intervention.

PubMed

Fricke, Nicola; Griesche, Stefan; Schieben, Anna; Hesse, Tobias; Baumann, Martin

2015-10-01

The study investigated driver behavior toward an automatic steering intervention of a collision mitigation system. Forty participants were tested in a driving simulator and confronted with an inevitable collision. They performed a naïve drive and afterwards a repeated exposure in which they were told to hold the steering wheel loosely. In a third drive they experienced a false alarm situation. Data on driving behavior, i.e. steering and braking behavior as well as subjective data was assessed in the scenarios. Results showed that most participants held on to the steering wheel strongly or counter-steered during the system intervention during the first encounter. Moreover, subjective data collected after the first drive showed that the majority of drivers was not aware of the system intervention. Data from the repeated drive in which participants were instructed to hold the steering wheel loosely, led to significantly more participants holding the steering wheel loosely and thus complying with the instruction. This study seems to imply that without knowledge and information of the system about an upcoming intervention, the most prevalent driving behavior is a strong reaction with the steering wheel similar to an automatic steering reflex which decreases the system's effectiveness. Results of the second drive show some potential for countermeasures, such as informing drivers shortly before a system intervention in order to prevent inhibiting reactions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Refractive waveguide non-mechanical beam steering (NMBS) in the MWIR

NASA Astrophysics Data System (ADS)

Myers, Jason D.; Frantz, Jesse A.; Spillmann, Christopher M.; Bekele, Robel Y.; Kolacz, Jakub; Gotjen, Henry; Naciri, Jawad; Shaw, Brandon; Sanghera, Jas S.

2018-02-01

Beam steering is a crucial technology for a number of applications, including chemical sensing/mapping and light detection and ranging (LIDAR). Traditional beam steering approaches rely on mechanical movement, such as the realignment of mirrors in gimbal mounts. The mechanical approach to steering has several drawbacks, including large size, weight and power usage (SWAP), and frequent mechanical failures. Recently, alternative non-mechanical approaches have been proposed and developed, but these technologies do not meet the demanding requirements for many beam steering applications. Here, we highlight the development efforts into a particular non-mechanical beam steering (NMBS) approach, refractive waveguides, for application in the MWIR. These waveguides are based on an Ulrich-coupled slab waveguide with a liquid crystal (LC) top cladding; by selectively applying an electric field across the liquid crystal through a prismatic electrode, steering is achieved by creating refraction at prismatic interfaces as light propagates through the device. For applications in the MWIR, we describe a versatile waveguide architecture based on chalcogenide glasses that have a wide range of refractive indices, transmission windows, and dispersion properties. We have further developed robust shadow-masking methods to taper the subcladding layers in the coupling region. We have demonstrated devices with >10° of steering in the MWIR and a number of advantageous properties for beam steering applications, including low-power operation, compact size, and fast point-to-point steering.

Aortic ruptures in seat belt wearers.

PubMed

Arajärvi, E; Santavirta, S; Tolonen, J

1989-09-01

Several investigations have indicated that rupture of the thoracic aorta is one of the leading causes of immediate death in victims of road traffic accidents. In Finland in 1983, 92% of front-seat passengers were seat belt wearers on highways and 82% in build-up areas. The mechanisms of rupture of the aorta have been intensively investigated, but the relationship between seat belt wearing and injury mechanisms leading to aortic rupture is still largely unknown. This study comprises 4169 fatally injured victims investigated by the Boards of Traffic Accident Investigation of Insurance Companies during the period 1972 to 1985. Chest injuries were recorded as the main cause of death in 1121 (26.9%) victims, 207 (5.0%) of those victims having worn a seat belt. Aortic ruptures were found at autopsy in 98 victims and the exact information of the location of the aortic tears was available in 68. For a control group, we analyzed 72 randomly chosen unbelted victims who had a fatal aortic rupture in similar accidents. The location of the aortic rupture in unbelted victims was more often in the ascending aorta, especially in drivers, whereas in seat belt wearers the distal descending aorta was statistically more often ruptured, especially in right-front passengers (p less than 0.05). The steering wheel predominated statistically as the part of the car estimated to have caused the injury in unbelted victims (37/72), and some interior part of the car was the most common cause of fatal thoracic impacts in seat belt wearers (48/68) (p less than 0.001). The mechanism of rupture of the aorta in the classic site just distal to the subclavian artery seems to be rapid deceleration, although complex body movements are also responsible in side impact collisions. The main mechanism leading to rupture of the ascending aorta seems to be severe blow to the bony thorax. This also often causes associated thoracic injuries, such as heart rupture and sternal fracture. Injuries in the ascending aorta were mostly found in unbelted victims and were sustained in frontal impact collisions, the injury-causing part of the car being the steering wheel. Ruptures of the distal descending part of the aorta were frequently associated with fractures of the thoracic vertebra.

Effects of beef production system on animal performance and carcass characteristics.

PubMed

Maxwell, C L; Krehbiel, C R; Wilson, B K; Johnson, B T; Bernhard, B C; O'Neill, C F; VanOverbeke, D L; Mafi, G G; Step, D L; Richards, C J

2014-12-01

The objective of this study was to evaluate conventional (CONV) and natural (NAT) beef production systems from annual pasture through finishing through grazing. Beef steers (n=180, initial BW=250±19 kg) were assigned randomly to 2 treatments in the pasture phase. Steers were implanted with 40 mg of trenbolone acetate (TBA), 8 mg estradiol, and 29 mg tylosin tartrate (CONV), or received no implant (NAT). Steers on the 2 treatments grazed wheat or cereal rye for 109 d. Conventional steers had an 18.5% improvement in ADG (1.22 vs. 1.03 kg/d, P<0.01) and a heavier final BW (385 vs. 366 kg, P<0.01) compared with NAT steers. Following the pasture phase, steers (n=160 steers, 5 steers/pen, 8 pens/treatment) were assigned to a 2×2 factorial in the feedlot phase. Production system (NAT vs. CONV) was maintained from the pasture phase, and the second factor was 7 vs. 12% low-quality roughage (DM basis, LOW vs. HIGH). During finishing, CONV steers were given 120 mg of TBA and 24 mg estradiol at processing, fed monensin and tylosin, and fed zilpaterol hydrochloride for the last 20 d of the experiment. There were no program×roughage level interactions (P>0.07). The CONV steers ate 6.9% more feed (11.8 vs. 11.0 kg/d, P<0.01), gained 28.4% faster (1.90 vs. 1.48 kg/d, P<0.01), and were 24.2% more efficient (0.164 vs. 0.132, P<0.01) compared with NAT steers. The LOW steers had greater G:F (0.153 vs. 0.144, P<0.01) compared with HIGH steers. There was a 28.3% improvement in estimated carcass weight gain (1.36 vs. 1.06 kg/d), 18.6% improvement in carcass efficiency (0.115 vs. 0.097, P<0.01), and 21.6% improvement (1.52 vs. 1.25 Mcal/kg, P<0.01) in calculated dietary NEg for CONV compared with NAT steers. Hot carcass weight was increased by 62 kg (424 vs. 362 kg, P<0.01) and LM area was increased by 16.9 cm2 (100.9 vs. 84.0 cm2, P<0.01), decreasing USDA yield grade (YG, 3.09 vs. 3.54, P<0.01) for CONV steers compared with NAT steers. Natural steers had a greater percentage of carcasses in the upper 2/3 of USDA Choice grade (48.7 vs. 18.7%, P<0.01), a greater percentage of YG 4 and 5 carcasses (25.4 vs. 9.3%, P<0.01), and a greater percentage of abscessed livers (39.6 vs. 10.5%, P<0.01) compared with CONV steers. The results show that CONV production results in more rapid and efficient production that resulted in heavier carcasses with superior YG and desirable quality grades with both roughage levels.

33 CFR 164.25 - Tests before entering or getting underway.

Code of Federal Regulations, 2011 CFR

2011-07-01

... remote steering gear control system. (ii) Each steering position located on the navigating bridge. (iii) The main steering gear from the alternative power supply, if installed. (iv) Each rudder angle indicator in relation to the actual position of the rudder. (v) Each remote steering gear control system...

33 CFR 164.25 - Tests before entering or getting underway.

Code of Federal Regulations, 2010 CFR

2010-07-01

... remote steering gear control system. (ii) Each steering position located on the navigating bridge. (iii) The main steering gear from the alternative power supply, if installed. (iv) Each rudder angle indicator in relation to the actual position of the rudder. (v) Each remote steering gear control system...

46 CFR 115.814 - Steering systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Steering systems. 115.814 Section 115.814 Shipping COAST... Inspections § 115.814 Steering systems. At each initial and subsequent inspection for certification the owner or managing operator shall be prepared to test the steering systems of the vessel and make them...

46 CFR 115.814 - Steering systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Steering systems. 115.814 Section 115.814 Shipping COAST... Inspections § 115.814 Steering systems. At each initial and subsequent inspection for certification the owner or managing operator shall be prepared to test the steering systems of the vessel and make them...

46 CFR 115.814 - Steering systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Steering systems. 115.814 Section 115.814 Shipping COAST... Inspections § 115.814 Steering systems. At each initial and subsequent inspection for certification the owner or managing operator shall be prepared to test the steering systems of the vessel and make them...

46 CFR 176.814 - Steering systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Steering systems. 176.814 Section 176.814 Shipping COAST...) INSPECTION AND CERTIFICATION Material Inspections § 176.814 Steering systems. At each initial and subsequent inspection for certification the owner or managing operator shall be prepared to test the steering systems of...

46 CFR 176.814 - Steering systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Steering systems. 176.814 Section 176.814 Shipping COAST...) INSPECTION AND CERTIFICATION Material Inspections § 176.814 Steering systems. At each initial and subsequent inspection for certification the owner or managing operator shall be prepared to test the steering systems of...

46 CFR 176.814 - Steering systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Steering systems. 176.814 Section 176.814 Shipping COAST...) INSPECTION AND CERTIFICATION Material Inspections § 176.814 Steering systems. At each initial and subsequent inspection for certification the owner or managing operator shall be prepared to test the steering systems of...

33 CFR 401.18 - Steering lights.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Steering lights. 401.18 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Condition of Vessels § 401.18 Steering lights. Every vessel shall be equipped with: (a) A steering light located on the centerline at or near the stem of the...

33 CFR 401.18 - Steering lights.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Steering lights. 401.18 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Condition of Vessels § 401.18 Steering lights. Every vessel shall be equipped with: (a) A steering light located on the centerline at or near the stem of the...

33 CFR 401.18 - Steering lights.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Steering lights. 401.18 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Condition of Vessels § 401.18 Steering lights. Every vessel shall be equipped with: (a) A steering light located on the centerline at or near the stem of the...

33 CFR 401.18 - Steering lights.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Steering lights. 401.18 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Condition of Vessels § 401.18 Steering lights. Every vessel shall be equipped with: (a) A steering light located on the centerline at or near the stem of the...

33 CFR 401.18 - Steering lights.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Steering lights. 401.18 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Condition of Vessels § 401.18 Steering lights. Every vessel shall be equipped with: (a) A steering light located on the centerline at or near the stem of the...

Experimental temporal quantum steering

PubMed Central

Bartkiewicz, Karol; Černoch, Antonín; Lemr, Karel; Miranowicz, Adam; Nori, Franco

2016-01-01

Temporal steering is a form of temporal correlation between the initial and final state of a quantum system. It is a temporal analogue of the famous Einstein-Podolsky-Rosen (spatial) steering. We demonstrate, by measuring the photon polarization, that temporal steering allows two parties to verify if they have been interacting with the same particle, even if they have no information about what happened with the particle in between the measurements. This is the first experimental study of temporal steering. We also performed experimental tests, based on the violation of temporal steering inequalities, of the security of two quantum key distribution protocols against individual attacks. Thus, these results can lead to applications for secure quantum communications and quantum engineering. PMID:27901121

Investigation of Motorcycle Steering Torque Components

NASA Astrophysics Data System (ADS)

Cossalter, V.; Lot, R.; Massaro, M.; Peretto, M.

2011-10-01

When driving along a circular path, the rider controls a motorcycle mainly by the steering torque. This work addresses an in-depth analysis of the steady state cornering and in particular the decomposition of the motorcycle steering torque in its main components, such as road-tyre forces, gyroscopic torques, centrifugal and gravity effects. A detailed and experimentally validated multibody model of the motorcycle is used herein to analyze the steering torque components at different speeds and lateral accelerations. First the road tests are compared with the numerical results for three different vehicles and then a numerical investigation is carried out to decompose the steering torque. Finally, the effect of longitudinal acceleration and deceleration on steering torque components is presented.

Getting the most out of additional guidance information in deformable image registration by leveraging multi-objective optimization

NASA Astrophysics Data System (ADS)

Alderliesten, Tanja; Bosman, Peter A. N.; Bel, Arjan

2015-03-01

Incorporating additional guidance information, e.g., landmark/contour correspondence, in deformable image registration is often desirable and is typically done by adding constraints or cost terms to the optimization function. Commonly, deciding between a "hard" constraint and a "soft" additional cost term as well as the weighting of cost terms in the optimization function is done on a trial-and-error basis. The aim of this study is to investigate the advantages of exploiting guidance information by taking a multi-objective optimization perspective. Hereto, next to objectives related to match quality and amount of deformation, we define a third objective related to guidance information. Multi-objective optimization eliminates the need to a-priori tune a weighting of objectives in a single optimization function or the strict requirement of fulfilling hard guidance constraints. Instead, Pareto-efficient trade-offs between all objectives are found, effectively making the introduction of guidance information straightforward, independent of its type or scale. Further, since complete Pareto fronts also contain less interesting parts (i.e., solutions with near-zero deformation effort), we study how adaptive steering mechanisms can be incorporated to automatically focus more on solutions of interest. We performed experiments on artificial and real clinical data with large differences, including disappearing structures. Results show the substantial benefit of using additional guidance information. Moreover, compared to the 2-objective case, additional computational cost is negligible. Finally, with the same computational budget, use of the adaptive steering mechanism provides superior solutions in the area of interest.

Multi-functional Electric Module for a Vehicle

NASA Technical Reports Server (NTRS)

Waligora, Thomas M. (Inventor); Fraser-Chanpong, Nathan (Inventor); Figuered, Joshua M. (Inventor); Reed, Ryan (Inventor); Akinyode, Akinjide Akinniyi (Inventor); Spain, Ivan (Inventor); Dawson, Andrew D. (Inventor); Herrera, Eduardo (Inventor); Markee, Mason M. (Inventor); Bluethmann, William J. (Inventor)

2015-01-01

A multi-functional electric module (eModule) is provided for a vehicle having a chassis, a master controller, and a drive wheel having a propulsion-braking module. The eModule includes a steering control assembly, mounting bracket, propulsion control assembly, brake controller, housing, and control arm. The steering control assembly includes a steering motor controlled by steering controllers in response to control signals from the master controller. A mounting feature of the bracket connects to the chassis. The propulsion control assembly and brake controller are in communication with the propulsion-braking module. The control arm connects to the lower portion and contains elements of a suspension system, with the control arm being connectable to the drive wheel via a wheel input/output block. The controllers are responsive to the master controller to control a respective steering, propulsion, and braking function. The steering motor may have a dual-wound stator with windings controlled via the respective steering controllers.

Demonstration of Monogamy Relations for Einstein-Podolsky-Rosen Steering in Gaussian Cluster States.

PubMed

Deng, Xiaowei; Xiang, Yu; Tian, Caixing; Adesso, Gerardo; He, Qiongyi; Gong, Qihuang; Su, Xiaolong; Xie, Changde; Peng, Kunchi

2017-06-09

Understanding how quantum resources can be quantified and distributed over many parties has profound applications in quantum communication. As one of the most intriguing features of quantum mechanics, Einstein-Podolsky-Rosen (EPR) steering is a useful resource for secure quantum networks. By reconstructing the covariance matrix of a continuous variable four-mode square Gaussian cluster state subject to asymmetric loss, we quantify the amount of bipartite steering with a variable number of modes per party, and verify recently introduced monogamy relations for Gaussian steerability, which establish quantitative constraints on the security of information shared among different parties. We observe a very rich structure for the steering distribution, and demonstrate one-way EPR steering of the cluster state under Gaussian measurements, as well as one-to-multimode steering. Our experiment paves the way for exploiting EPR steering in Gaussian cluster states as a valuable resource for multiparty quantum information tasks.

Demonstration of Monogamy Relations for Einstein-Podolsky-Rosen Steering in Gaussian Cluster States

NASA Astrophysics Data System (ADS)

Deng, Xiaowei; Xiang, Yu; Tian, Caixing; Adesso, Gerardo; He, Qiongyi; Gong, Qihuang; Su, Xiaolong; Xie, Changde; Peng, Kunchi

2017-06-01

Understanding how quantum resources can be quantified and distributed over many parties has profound applications in quantum communication. As one of the most intriguing features of quantum mechanics, Einstein-Podolsky-Rosen (EPR) steering is a useful resource for secure quantum networks. By reconstructing the covariance matrix of a continuous variable four-mode square Gaussian cluster state subject to asymmetric loss, we quantify the amount of bipartite steering with a variable number of modes per party, and verify recently introduced monogamy relations for Gaussian steerability, which establish quantitative constraints on the security of information shared among different parties. We observe a very rich structure for the steering distribution, and demonstrate one-way EPR steering of the cluster state under Gaussian measurements, as well as one-to-multimode steering. Our experiment paves the way for exploiting EPR steering in Gaussian cluster states as a valuable resource for multiparty quantum information tasks.

46 CFR 58.25-55 - Overcurrent protection for steering-gear systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... overcurrent protection except short-circuit protection that is instantaneous and rated at 400% to 500% of— (1... for steering-gear systems. (a) Each feeder circuit for steering must be protected by a circuit breaker... motor for an alternating-current motor. (b) No feeder circuit for steering may have any overcurrent...

46 CFR 61.20-1 - Steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Steering gear. 61.20-1 Section 61.20-1 Shipping COAST... Periodic Tests of Machinery and Equipment § 61.20-1 Steering gear. (a) The marine inspector must inspect the steering gear at each inspection for certification for vessels whose Certificate of Inspections...

46 CFR 78.47-55 - Instructions for changing steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Instructions for changing steering gear. 78.47-55... OPERATIONS Markings for Fire and Emergency Equipment, Etc. § 78.47-55 Instructions for changing steering gear..., relating in order, the different steps to be taken in changing to the emergency steering gear. Each clutch...

Multipartite steering inequalities based on entropic uncertainty relations

NASA Astrophysics Data System (ADS)

Riccardi, Alberto; Macchiavello, Chiara; Maccone, Lorenzo

2018-05-01

We investigate quantum steering for multipartite systems by using entropic uncertainty relations. We introduce entropic steering inequalities whose violation certifies the presence of different classes of multipartite steering. These inequalities witness both steerable states and genuine multipartite steerable states. Furthermore, we study their detection power for several classes of states of a three-qubit system.

46 CFR 113.43-5 - Power supply.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Power supply. 113.43-5 Section 113.43-5 Shipping COAST... SYSTEMS AND EQUIPMENT Steering Failure Alarm Systems § 113.43-5 Power supply. Each steering failure alarm system must be supplied by a circuit that: (a) Is independent of other steering gear system and steering...

46 CFR 113.43-5 - Power supply.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Power supply. 113.43-5 Section 113.43-5 Shipping COAST... SYSTEMS AND EQUIPMENT Steering Failure Alarm Systems § 113.43-5 Power supply. Each steering failure alarm system must be supplied by a circuit that: (a) Is independent of other steering gear system and steering...

Toward Intelligent Systems for Testing. Technical Report LSP-1.

ERIC Educational Resources Information Center

Lesgold, Alan; And Others

This report illustrates one way in which the technologies of testing might combine with cognitive science techniques to help steer instruction. Steering testing is brief diagnostic testing that steers, or individualizes, the course of instruction. Steering testing uses simple heuristics for reasoning about the level of a student's competence in a…

Experimental Demonstration of the Einstein-Podolsky-Rosen Steering Game Based on the All-Versus-Nothing Proof

NASA Astrophysics Data System (ADS)

Sun, Kai; Xu, Jin-Shi; Ye, Xiang-Jun; Wu, Yu-Chun; Chen, Jing-Ling; Li, Chuan-Feng; Guo, Guang-Can

2014-10-01

Einstein-Podolsky-Rosen (EPR) steering, a generalization of the original concept of "steering" proposed by Schrödinger, describes the ability of one system to nonlocally affect another system's states through local measurements. Some experimental efforts to test EPR steering in terms of inequalities have been made, which usually require many measurement settings. Analogy to the "all-versus-nothing" (AVN) proof of Bell's theorem without inequalities, testing steerability without inequalities would be more strong and require less resources. Moreover, the practical meaning of steering implies that it should also be possible to store the state information on the side to be steered, a result that has not yet been experimentally demonstrated. Using a recent AVN criterion for two-qubit entangled states, we experimentally implement a practical steering game using quantum memory. Furthermore, we develop a theoretical method to deal with the noise and finite measurement statistics within the AVN framework and apply it to analyze the experimental data. Our results clearly show the facilitation of the AVN criterion for testing steerability and provide a particularly strong perspective for understanding EPR steering.

Monogamy inequalities for the Einstein-Podolsky-Rosen paradox and quantum steering

NASA Astrophysics Data System (ADS)

Reid, M. D.

2013-12-01

Monogamy inequalities for the way bipartite Einstein-Podolsky-Rosen (EPR) steering can be distributed among N systems are derived. One set of inequalities is based on witnesses with two measurement settings, and may be used to demonstrate correlation of outcomes between two parties, that cannot be shared with more parties. It is shown that the monogamy for steering is directional. Two parties cannot independently demonstrate steering of a third system, using the same two-setting steering witness, but it is possible for one party to steer two independent systems. This result explains the monogamy of two-setting Bell inequality violations and the sensitivity of the continuous variable (CV) EPR criterion to losses on the steering party. We generalize to m settings. A second type of monogamy relation gives the quantitative amount of sharing possible, when the number of parties is less than or equal to m, and takes a form similar to the Coffman-Kundu-Wootters relation for entanglement. The results enable characterization of the tripartite steering for CV Gaussian systems and qubit Greenberger-Horne-Zeilinger and W states.

Steering Bell-diagonal states

PubMed Central

Quan, Quan; Zhu, Huangjun; Liu, Si-Yuan; Fei, Shao-Ming; Fan, Heng; Yang, Wen-Li

2016-01-01

We investigate the steerability of two-qubit Bell-diagonal states under projective measurements by the steering party. In the simplest nontrivial scenario of two projective measurements, we solve this problem completely by virtue of the connection between the steering problem and the joint-measurement problem. A necessary and sufficient criterion is derived together with a simple geometrical interpretation. Our study shows that a Bell-diagonal state is steerable by two projective measurements iff it violates the Clauser-Horne-Shimony-Holt (CHSH) inequality, in sharp contrast with the strict hierarchy expected between steering and Bell nonlocality. We also introduce a steering measure and clarify its connections with concurrence and the volume of the steering ellipsoid. In particular, we determine the maximal concurrence and ellipsoid volume of Bell-diagonal states that are not steerable by two projective measurements. Finally, we explore the steerability of Bell-diagonal states under three projective measurements. A simple sufficient criterion is derived, which can detect the steerability of many states that are not steerable by two projective measurements. Our study offers valuable insight on steering of Bell-diagonal states as well as the connections between entanglement, steering, and Bell nonlocality. PMID:26911250

Two dimensional thermo-optic beam steering using a silicon photonic optical phased array

NASA Astrophysics Data System (ADS)

Mahon, Rita; Preussner, Marcel W.; Rabinovich, William S.; Goetz, Peter G.; Kozak, Dmitry A.; Ferraro, Mike S.; Murphy, James L.

2016-03-01

Components for free space optical communication terminals such as lasers, amplifiers, and receivers have all seen substantial reduction in both size and power consumption over the past several decades. However, pointing systems, such as fast steering mirrors and gimbals, have remained large, slow and power-hungry. Optical phased arrays provide a possible solution for non-mechanical beam steering devices that can be compact and lower in power. Silicon photonics is a promising technology for phased arrays because it has the potential to scale to many elements and may be compatible with CMOS technology thereby enabling batch fabrication. For most free space optical communication applications, two-dimensional beam steering is needed. To date, silicon photonic phased arrays have achieved two-dimensional steering by combining thermo-optic steering, in-plane, with wavelength tuning by means of an output grating to give angular tuning, out-of-plane. While this architecture might work for certain static communication links, it would be difficult to implement for moving platforms. Other approaches have required N2 controls for an NxN element phased array, which leads to complexity. Hence, in this work we demonstrate steering using the thermo-optic effect for both dimensions with a simplified steering mechanism requiring only two control signals, one for each steering dimension.

A channel-based framework for steering, non-locality and beyond

NASA Astrophysics Data System (ADS)

Hoban, Matty J.; Belén Sainz, Ana

2018-05-01

Non-locality and steering are both non-classical phenomena witnessed in nature as a result of quantum entanglement. It is now well-established that one can study non-locality independently of the formalism of quantum mechanics, in the so-called device-independent framework. With regards to steering, although one cannot study it completely independently of the quantum formalism, ‘post-quantum steering’ has been described, which is steering that cannot be reproduced by measurements on entangled states but does not lead to superluminal signalling. In this work we present a framework based on the study of quantum channels in which one can study steering (and non-locality) in quantum theory and beyond. In this framework, we show that kinds of steering, whether quantum or post-quantum, are directly related to particular families of quantum channels that have been previously introduced by Beckman et al (2001 Phys. Rev. A 64 052309). Utilizing this connection we also demonstrate new analytical examples of post-quantum steering, give a quantum channel interpretation of almost quantum non-locality and steering, easily recover and generalize the celebrated Gisin–Hughston–Jozsa–Wootters theorem, and initiate the study of post-quantum Buscemi non-locality and non-classical teleportation. In this way, we see post-quantum non-locality and steering as just two aspects of a more general phenomenon.

Influence of different shoulder-elbow configurations on steering precision and steering velocity in automotive context.

PubMed

Schmidt, Susanne; Seiberl, Wolfgang; Schwirtz, Ansgar

2015-01-01

Ergonomic design requirements are needed to develop optimum vehicle interfaces for the driver. The majority of the current specifications consider only anthropometric conditions and subjective evaluations of comfort. This paper examines specific biomechanical aspects to improve the current ergonomic requirements. Therefore, a research which involved 40 subjects was carried out to obtain more knowledge in the field of steering movement while driving a car. Five different shoulder-elbow joint configurations were analyzed using a driving simulator to find optimum posture for driving in respect of steering precision and steering velocity. Therefore, a 20 s precision test and a test to assess maximum steering velocity over a range of 90° steering motion have been conducted. The results show that driving precision, as well as maximum steering velocity, are significantly increased in mid-positions (elbow angles of 95° and 120°) compared to more flexed (70°) or extended (145° and 160°) postures. We conclude that driver safety can be enhanced by implementing these data in the automotive design process because faster and highly precise steering can be important during evasive actions and in accident situations. In addition, subjective comfort rating, analyzed with questionnaires, confirmed experimental results. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Rumen microbial changes in cattle fed diets with or without salinomycin.

PubMed

Olumeyan, D B; Nagaraja, T G; Miller, G W; Frey, R A; Boyer, J E

1986-02-01

Four rumen-fistulated steers, randomly assigned to two groups (control and salinomycin fed) were used to monitor the changes in rumen microbial populations and volatile fatty acids (VFA) concentrations associated with feeding salinomycin (0.22 mg X kg-1 X day-1). Steers were adapted to an alfalfa hay and grain (80:20) diet before supplementing the diet with salinomycin, and then the diet was changed to 50:50 and 20:80 ratios of alfalfa hay to grain at 2-week intervals. Rumen samples for total and selective enumeration of anaerobic bacteria. VFA analysis, and enumeration of protozoa were collected during the 80:20 alfalfa hay-to-grain diet before salinomycin feeding, and during the 80:20, 50:50, and 20:80 hay-to-grain diets with salinomycin. At each sampling period, rumen samples were collected at 3 h after feeding on three consecutive days. Salinomycin feeding had no effect on rumen pH and total VFA concentration. The acetate-to-propionate ratio was significantly lower in salinomycin-fed steers than in the control. The molar proportion of butyrate increased in both control and salinomycin-fed steers. Total anaerobic bacterial counts were lower in salinomycin-fed steers than in the control steers after 8 weeks of salinomycin feeding. Salinomycin-resistant bacteria increased from 7.6 to 15.6% in salinomycin-fed steers but remained unchanged in control steers. Salinomycin had no effect on cellulolytic and lactate-utilizing bacteria, but the proportion of amylolytic bacteria was higher in salinomycin-fed steers than in control steers. The total number of protozoa decreased initially in salinomycin-fed steers. The initial reduction was due to reduced numbers of Entodinium species. Holotrichs were unaffected by salinomycin feeding.

Predicting red meat yields in carcasses from beef-type and calf-fed Holstein steers using the United States Department of Agriculture calculated yield grade.

PubMed

Lawrence, T E; Elam, N A; Miller, M F; Brooks, J C; Hilton, G G; VanOverbeke, D L; McKeith, F K; Killefer, J; Montgomery, T H; Allen, D M; Griffin, D B; Delmore, R J; Nichols, W T; Streeter, M N; Yates, D A; Hutcheson, J P

2010-06-01

Analyses were conducted to evaluate the ability of the USDA yield grade equation to detect differences in subprimal yield of beef-type steers and calf-fed Holstein steers that had been fed zilpaterol hydrochloride (ZH; Intervet Inc., Millsboro, DE) as well as those that had not been fed ZH. Beef-type steer (n = 801) and calf-fed Holstein steer (n = 235) carcasses were fabricated into subprimal cuts and trim. Simple correlations between calculated yield grades and total red meat yields ranged from -0.56 to -0.62 for beef-type steers. Reliable correlations from calf-fed Holstein steers were unobtainable; the probability of a type I error met or exceeded 0.39. Linear models were developed for the beef-type steers to predict total red meat yield based on calculated USDA yield grade within each ZH duration. At an average calculated USDA yield grade of 2.9, beef-type steer carcasses that had not been fed ZH had an estimated 69.4% red meat yield, whereas those fed ZH had an estimated 70.7% red meat yield. These results indicate that feeding ZH increased red meat yield by 1.3% at a constant calculated yield grade. However, these data also suggest that the calculated USDA yield grade score is a poor and variable estimator (adjusted R(2) of 0.31 to 0.38) of total red meat yield of beef-type steer carcasses, regardless of ZH feeding. Moreover, no relationship existed (adjusted R(2) of 0.00 to 0.01) for calf-fed Holstein steer carcasses, suggesting the USDA yield grade is not a valid estimate of calf-fed Holstein red meat yield.

Steer-PROP: a GRASE-PROPELLER sequence with interecho steering gradient pulses.

PubMed

Srinivasan, Girish; Rangwala, Novena; Zhou, Xiaohong Joe

2018-05-01

This study demonstrates a novel PROPELLER (periodically rotated overlapping parallel lines with enhanced reconstruction) pulse sequence, termed Steer-PROP, based on gradient and spin echo (GRASE), to reduce the imaging times and address phase errors inherent to GRASE. The study also illustrates the feasibility of using Steer-PROP as an alternative to single-shot echo planar imaging (SS-EPI) to produce distortion-free diffusion images in all imaging planes. Steer-PROP uses a series of blip gradient pulses to produce N (N = 3-5) adjacent k-space blades in each repetition time, where N is the number of gradient echoes in a GRASE sequence. This sampling strategy enables a phase correction algorithm to systematically address the GRASE phase errors as well as the motion-induced phase inconsistency. Steer-PROP was evaluated on phantoms and healthy human subjects at both 1.5T and 3.0T for T 2 - and diffusion-weighted imaging. Steer-PROP produced similar image quality as conventional PROPELLER based on fast spin echo (FSE), while taking only a fraction (e.g., 1/3) of the scan time. The robustness against motion in Steer-PROP was comparable to that of FSE-based PROPELLER. Using Steer-PROP, high quality and distortion-free diffusion images were obtained from human subjects in all imaging planes, demonstrating a considerable advantage over SS-EPI. The proposed Steer-PROP sequence can substantially reduce the scan times compared with FSE-based PROPELLER while achieving adequate image quality. The novel k-space sampling strategy in Steer-PROP not only enables an integrated phase correction method that addresses various sources of phase errors, but also minimizes the echo spacing compared with alternative sampling strategies. Steer-PROP can also be a viable alternative to SS-EPI to decrease image distortion in all imaging planes. Magn Reson Med 79:2533-2541, 2018. © 2017 International Society for Magnetic Resonance in Medicine. © 2017 International Society for Magnetic Resonance in Medicine.

Effect of dietary trace mineral supplementation and a multi-element trace mineral injection on shipping response and growth performance of beef cattle.

PubMed

Genther, O N; Hansen, S L

2014-06-01

To examine the effect of trace mineral (TM) status and TM injection on growth performance and carcass characteristics in beef cattle, 40 steers were used in a growing and finishing study. Steers were stratified by weight (323 ± 14.8 kg) and assigned to 1 of 2 treatments for an 84-d depletion period: 1) a corn silage-based diet supplemented with Cu, Mn, Se, and Zn to meet or exceed NRC recommendations (CON), or 2) CON diet without supplemental Cu, Mn, Se, or Zn but supplemented with 300 mg Fe and 5 mg Mo/kg diet DM as dietary TM antagonists (DEF) to induce mild deficiencies. To mimic shipping stress, steers were shipped for 20 h on d 88 and were received back on d 89. On d 91 an equal number of steers from both dietary treatments were injected with sterilized saline (SAL) or Multimin 90 (MM; containing 15, 60, 10, and 5 mg/mL of Cu, Zn, Mn, and Se, respectively) at a dose of 1 mL/68 kg BW. Steers were fed a common finishing diet supplemented with 10 mg Cu, 20 mg Mn, 0.1 mg Se, and 30 mg Zn/kg diet DM for the 90-d repletion period. Steers were harvested 91 d postinjection and carcass data were collected. During the depletion period, diet did not affect BW, ADG, DMI, or G:F (P > 0.20). During the shipping period (defined as the time between 2-d consecutive weights on d 83 and 84 and d 90 and 91), DEF steers tended to lose more weight per day than CON steers (P = 0.06) and had lesser DMI (P = 0.03), suggesting that response to shipping stress may be modulated by TM status. During the repletion period, ADG of DEF + MM steers was greater (P = 0.03) compared with DEF + SAL and was not different (P = 0.92) among CON + MM and CON + SAL steers. There was no effect of diet or injection on HCW or dressing percentage (P > 0.20). Within the CON group, TM injection decreased yield grade (P = 0.03) but did not affect yield grade of DEF steers (P > 0.20). Steers given TM injection had a larger rib eye area (P = 0.04) regardless of previous diet. Interestingly, both diet and injection affected marbling scores (MS), where CON steers had greater MS than DEF steers (P = 0.01) and MM steers had greater MS than SAL steers (P = 0.04). These results indicate that adequate TM nutrition is essential for marbling development, during both the growing and finishing phases. Overall, an injectable mineral improved rib eye area and MS regardless of initial TM status and improved growth of mildly TM deficient steers.

49 CFR 571.126 - Standard No. 126; Electronic stability control systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... counterclockwise steering, and the other series uses clockwise steering. The maximum time permitted between each... or side slip derivative with respect to time; (4) That has a means to monitor driver steering inputs... dwell steering input (time T0 + 1 in Figure 1) must not exceed 35 percent of the first peak value of yaw...

49 CFR 571.126 - Standard No. 126; Electronic stability control systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... counterclockwise steering, and the other series uses clockwise steering. The maximum time permitted between each... or side slip derivative with respect to time; (4) That has a means to monitor driver steering inputs... dwell steering input (time T0 + 1 in Figure 1) must not exceed 35 percent of the first peak value of yaw...

Steer responses to feeding soybean hulls and steroid hormone implantation on toxic tall fescue pasture

USDA-ARS?s Scientific Manuscript database

Yearling steers were grazed on endophyte-infected ‘Kentucky-31’ tall fescue (Lolium arundinaceum) pastures for 77 days in 2007 and for 86 days in 2008 to evaluate effects of feeding pelleted soybean hulls (PSBH) and steroid hormone implants (SHI) on steer performance and physiology. Steers were str...

46 CFR 97.37-33 - Instructions for changing steering gear.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Instructions for changing steering gear. 97.37-33... steering gear. (a) Instructions in at least 1/2 inch letters and figures shall be posted in the steering... gear. Each clutch, gear, wheel, lever, valve, or switch which is used during the changeover shall be...

46 CFR 78.17-15 - Steering gear, whistle, and means of communication.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Steering gear, whistle, and means of communication. 78... VESSELS OPERATIONS Tests, Drills, and Inspections § 78.17-15 Steering gear, whistle, and means of communication. (a) On all vessels making a voyage of more than 48 hours' duration, the entire steering gear, the...

46 CFR 196.15-3 - Steering gear, whistle, and means of communication.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Steering gear, whistle, and means of communication. 196... RESEARCH VESSELS OPERATIONS Test, Drills, and Inspections § 196.15-3 Steering gear, whistle, and means of communication. (a) On all vessels making a voyage of more than 48 hours duration, the entire steering gear, the...

46 CFR 130.140 - Steering on OSVs of 100 or more gross tons.

Code of Federal Regulations, 2014 CFR

2014-10-01

... maximum astern speed. (2) A hydraulic system with a maximum allowable working pressure of not more than 12... of this chapter; or (2) Requirements for a hydraulic-helm steering-system in paragraph (b) of this section. (b) Each hydraulic-helm steering-system must have the following: (1) A main steering gear of...

Chromium supplementation enhances the acute phase response of steers to a lipopolysaccharide (LPS) challenge

USDA-ARS?s Scientific Manuscript database

The study examined the effect of chromium supplementation on the response of steers to an LPS challenge. Twenty crossbred steers (235±4 kg BW) received 0 ppb (Control; C) or 200 ppb chromium propionate (CHR) for 55 days. Steers were fitted with jugular catheters and rectal temperature (RT) recording...

Ultra-compact laser beam steering device using holographically formed two dimensional photonic crystal.

PubMed

Dou, Xinyuan; Chen, Xiaonan; Chen, Maggie Yihong; Wang, Alan Xiaolong; Jiang, Wei; Chen, Ray T

2010-03-01

In this paper, we report the theoretical study of polymer-based photonic crystals for laser beam steering which is based on the superprism effect as well as the experiment fabrication of the two dimensional photonic crystals for the laser beam steering. Superprism effect, the principle for beam steering, was separately studied in details through EFC (Equifrequency Contour) analysis. Polymer based photonic crystals were fabricated through double exposure holographic interference method using SU8-2007. The experiment results showed a beam steering angle of 10 degree for 30 nm wavelength variation.

Controlled Asymmetry of Einstein-Podolsky-Rosen Steering with an Injected Nondegenerate Optical Parametric Oscillator

NASA Astrophysics Data System (ADS)

Olsen, M. K.

2017-10-01

We propose and analyze a nonlinear optical apparatus in which the direction of asymmetric steering is controllable within the apparatus, rather than by adding noise to measurements. Using a nondegenerate parametric oscillator with an injected signal field, we show how the directionality and extent of the steering can be readily controlled for output modes that can be up to one octave apart. The two down-converted modes, which exhibit the greater violations of the steering inequalities, can also be controlled to exhibit asymmetric steering in some regimes.

Screening of 23 β-lactams in foodstuffs by LC-MS/MS using an alkaline QuEChERS-like extraction.

PubMed

Bessaire, Thomas; Mujahid, Claudia; Beck, Andrea; Tarres, Adrienne; Savoy, Marie-Claude; Woo, Pei-Mun; Mottier, Pascal; Desmarchelier, Aurélien

2018-04-01

A fast and robust high performance LC-MS/MS screening method was developed for the analysis of β-lactam antibiotics in foods of animal origin: eggs, raw milk, processed dairy ingredients, infant formula, and meat- and fish-based products including baby foods. QuEChERS extraction with some adaptations enabled 23 drugs to be simultaneously monitored. Screening target concentrations were set at levels adequate to ensure compliance with current European, Chinese, US and Canadian regulations. The method was fully validated according to the European Community Reference Laboratories Residues Guidelines using 93 food samples of different composition. False-negative and false-positive rates were below 5% for all analytes. The method is adequate for use in high-routine laboratories. A 1-year study was additionally conducted to assess the stability of the 23 analytes in the working standard solution.

Matrix effects in pesticide multi-residue analysis by liquid chromatography-mass spectrometry.

PubMed

Kruve, Anneli; Künnapas, Allan; Herodes, Koit; Leito, Ivo

2008-04-11

Three sample preparation methods: Luke method (AOAC 985.22), QuEChERS (quick, easy, cheap, effective, rugged and safe) and matrix solid-phase dispersion (MSPD) were applied to different fruits and vegetables for analysis of 14 pesticide residues by high-performance liquid chromatography with electrospray ionization-mass spectrometry (HPLC/ESI/MS). Matrix effect, recovery and process efficiency of the sample preparation methods applied to different fruits and vegetables were compared. The Luke method was found to produce least matrix effect. On an average the best recoveries were obtained with the QuEChERS method. MSPD gave unsatisfactory recoveries for some basic pesticide residues. Comparison of matrix effects for different apple varieties showed high variability for some residues. It was demonstrated that the amount of co-extracting compounds that cause ionization suppression of aldicarb depends on the apple variety as well as on the sample preparation method employed.

Global helium particle balance in LHD

NASA Astrophysics Data System (ADS)

Motojima, G.; Masuzaki, S.; Tokitani, M.; Kasahara, H.; Yoshimura, Y.; Kobayashi, M.; Sakamoto, R.; Morisaki, T.; Miyazawa, J.; Akiyama, T.; Ohno, N.; Mutoh, T.; Yamada, H.; LHD Experiment Group

2015-08-01

Global helium particle balance in long-pulse discharges is analyzed for the first time in the Large Helical Device (LHD) with the plasma-facing components of the first wall and the divertor tiles composed of stainless steel and carbon, respectively. During the 2-min discharge sustained by ion cyclotron resonance heating (ICRH) and electron cyclotron heating (ECH), helium is observed to be highly retained in the wall (regarded as both the first wall and the divertor tiles). Almost all (about 96%) puffed helium particles (1.3 × 1022 He) are absorbed in the wall near the end of the discharge. Even though a dynamic retention is eliminated, 56% is still absorbed. The analysis is also applied to longer pulse discharges over 40 min by ICRH and ECH, indicating that the helium wall retention is dynamically changed in time. At the initial phase of the discharge, a mechanism for adsorbing helium other than dynamical retention is invoked.

Determination of pesticides in coconut (Cocos nucifera Linn.) water and pulp using modified QuEChERS and LC-MS/MS.

PubMed

Ferreira, Jordana Alves; Ferreira, Joana Maria Santos; Talamini, Viviane; Facco, Janice de Fátima; Rizzetti, Tiele Medianeira; Prestes, Osmar Damian; Adaime, Martha Bohrer; Zanella, Renato; Bottoli, Carla Beatriz Grespan

2016-12-15

The use of pesticides is directly linked to improvements in productivity and to the preservation of coconut palms. However pesticide analysis is necessary to determine whether pesticide residues in the food products containing coconut are within the maximum residue limits (MRLs), ensuring the quality of these products. This work aimed to develop a method for multiresidue determination of ten pesticides in coconut water and pulp using QuEChERS and LC-MS/MS. The method was effective in terms of selectivity, linearity, matrix effect, accuracy and precision, providing LOD of 3μgkg(-1), LOQ of 10μgkg(-1) and recoveries between 70 and 120% with RSD lower than 20%. The developed method was applied to 36 samples in which residues of carbendazim, carbofuran, cyproconazole and thiabendazole were found below the LOQ in coconut water and pulp. Copyright © 2016 Elsevier Ltd. All rights reserved.

Influence of rice whole-crop silage diet on growth performance, carcass and meat characteristics and muscle-related gene expression in Japanese Black steers.

PubMed

Shibata, Masahiro; Hikino, Yasuko; Imanari, Mai; Matsumoto, Kazunori; Yamamoto, Naoyuki

2016-07-01

The present study investigated the influence of a diet largely comprising rice whole-crop silage (rWCS) on growth performance, carcass and meat characteristics, and expression of genes involved in muscle growth of Japanese Black steers. Steers were randomly separated into rWCS-fed (rWCS ad libitum and restricted feeding of concentrate) and concentrate-fed groups. Total digestible nutrient intake and daily gain (DG) decreased in rWCS-fed steers in comparison with concentrate-fed steers, whereas dressed carcass weight and final body weight did not significantly differ between the groups. Decreases in drip loss in the muscle of rWCS-fed steers may be caused by α-tocopherol and β-carotene in muscle. Feeding large amounts of rWCS to steers may maintain quantitative productivity of beef steers equally to a concentrate-based diet, and improve the qualitative productivity. Results of gene expression suggest that activation of skeletal muscle growth in rWCS-fed steers may occur at the late fattening period owing to a decrease in myostatin and increase in myosin heavy chain gene expression. Preadipocyte factor-1 and myostatin genes may be strongly involved in the control of lipid accumulation. This rearing system would allow beef production to switch to rWCS-based diets from concentrate-based diets. © 2015 Japanese Society of Animal Science.

Enhancement of the acute phase response to lipopolysaccharide (LPS) challenge in steers supplemented with chromium

USDA-ARS?s Scientific Manuscript database

The study examined the effect of chromium supplementation on the response of steers to an LPS challenge. Twenty steers received a premix that added 0 (control) or 0.2 mg/kg of chromium (KemTRACE®brandChromiumProprionate 0.04%, Kemin Industries) to the total diet on a dry matter basis for 55 d. Steer...

Test of Einstein-Podolsky-Rosen Steering Based on the All-Versus-Nothing Proof

PubMed Central

Wu, Chunfeng; Chen, Jing-Ling; Ye, Xiang-Jun; Su, Hong-Yi; Deng, Dong-Ling; Wang, Zhenghan; Oh, C. H.

2014-01-01

In comparison with entanglement and Bell nonlocality, Einstein-Podolsky-Rosen steering is a newly emerged research topic and in its incipient stage. Although Einstein-Podolsky-Rosen steering has been explored via violations of steering inequalities both theoretically and experimentally, the known inequalities in the literatures are far from well-developed. As a result, it is not yet possible to observe Einstein-Podolsky-Rosen steering for some steerable mixed states. Recently, a simple approach was presented to identify Einstein-Podolsky-Rosen steering based on all-versus-nothing argument, offering a strong condition to witness the steerability of a family of two-qubit (pure or mixed) entangled states. In this work, we show that the all-versus-nothing proof of Einstein-Podolsky-Rosen steering can be tested by measuring the projective probabilities. Through the bound of probabilities imposed by local-hidden-state model, the proposed test shows that steering can be detected by the all-versus-nothing argument experimentally even in the presence of imprecision and errors. Our test can be implemented in many physical systems and we discuss the possible realizations of our scheme with non-Abelian anyons and trapped ions. PMID:24598858

Carcass characteristics and meat quality of Hereford sired steers born to beef-cross-dairy and Angus breeding cows.

PubMed

Coleman, Lucy W; Hickson, Rebecca E; Schreurs, Nicola M; Martin, Natalia P; Kenyon, Paul R; Lopez-Villalobos, Nicolas; Morris, Stephen T

2016-11-01

Steers from Angus, Angus×Holstein Friesian, Angus×Holstein Friesian-Jersey and Angus×Jersey cows and a Hereford sire were measured for their carcass and meat quality characteristics. Steers from the Angus×Holstein Friesian cows had a greater final body weight and carcass weight (P<0.05). Steers from Angus×Jersey cows had the lowest carcass weight and dressing-out percentage (P<0.05). There was a greater fat depth over the rump at 12 and 18months of age for the steers from Angus cows (P<0.05) but, not at 24months of age. The steers had similar meat quality characteristics across the breed groups. Steers from Angus×Holstein Friesian and Angus×Jersey cows had a higher ratio of n6 to n3 fatty acids. Using beef-cross-dairy cows to produce steers for meat production does not impact on meat quality. Using Jersey in the breed cross reduced the carcass tissues in the live weight and the potential meat yield. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Quantum steering: a review with focus on semidefinite programming.

PubMed

Cavalcanti, D; Skrzypczyk, P

2017-02-01

Quantum steering refers to the non-classical correlations that can be observed between the outcomes of measurements applied on half of an entangled state and the resulting post-measured states that are left with the other party. From an operational point of view, a steering test can be seen as an entanglement test where one of the parties performs uncharacterised measurements. Thus, quantum steering is a form of quantum inseparability that lies in between the well-known notions of Bell nonlocality and entanglement. Moreover, quantum steering is also related to several asymmetric quantum information protocols where some of the parties are considered untrusted. Because of these facts, quantum steering has received a lot of attention both theoretically and experimentally. The main goal of this review is to give an overview of how to characterise quantum steering through semidefinite programming. This characterisation provides efficient numerical methods to address a number of problems, including steering detection, quantification, and applications. We also give a brief overview of some important results that are not directly related to semidefinite programming. Finally, we make available a collection of semidefinite programming codes that can be used to study the topics discussed in this article.

Test of Einstein-Podolsky-Rosen steering based on the all-versus-nothing proof.

PubMed

Wu, Chunfeng; Chen, Jing-Ling; Ye, Xiang-Jun; Su, Hong-Yi; Deng, Dong-Ling; Wang, Zhenghan; Oh, C H

2014-03-06

In comparison with entanglement and Bell nonlocality, Einstein-Podolsky-Rosen steering is a newly emerged research topic and in its incipient stage. Although Einstein-Podolsky-Rosen steering has been explored via violations of steering inequalities both theoretically and experimentally, the known inequalities in the literatures are far from well-developed. As a result, it is not yet possible to observe Einstein-Podolsky-Rosen steering for some steerable mixed states. Recently, a simple approach was presented to identify Einstein-Podolsky-Rosen steering based on all-versus-nothing argument, offering a strong condition to witness the steerability of a family of two-qubit (pure or mixed) entangled states. In this work, we show that the all-versus-nothing proof of Einstein-Podolsky-Rosen steering can be tested by measuring the projective probabilities. Through the bound of probabilities imposed by local-hidden-state model, the proposed test shows that steering can be detected by the all-versus-nothing argument experimentally even in the presence of imprecision and errors. Our test can be implemented in many physical systems and we discuss the possible realizations of our scheme with non-Abelian anyons and trapped ions.

Applications of EPR steering in quantum teleportation and NOON states

NASA Astrophysics Data System (ADS)

Zárate, Laura Rosales

2018-04-01

Einstein-Podolsky-Rosen (EPR) steering refers to the type of correlations described in the EPR paradox, where one observer seems to affect ("steer") the state of other observer by using local measurements. There have been several works regarding characterization and quantification of EPR steering. One characteristic of this non-local correlation is that it can be asymmetric, while entanglement is symmetric. This asymmetric property is relevant for potential applications of EPR steering to quantum information, in particular to quantum cryptography and quantum teleportation. This latter refers to the process where one observer sends an unknown quantum state to Bob, who is in a different location. They communicate by classical means. Here we will show that EPR steering is a necessary resource to obtain secure continuous variable teleportation. We will also consider NOON states, which is an example of an entangled state. For this state, we will present a steering signature. This contribution reviews the work derived in Refs. [1] and [2], which was presented as an invited talk in ELAF 2017.

Manual and automatic control of surface effect ships. [operator steering servomechanisms analysis

NASA Technical Reports Server (NTRS)

Clement, W. F.; Shanahan, J. J.; Allen, R. W.

1975-01-01

A recent investigation of crew performance in the motion environment of a large generic high speed surface effect ship by means of a motion base simulation addressed some of the helmsman's control task with an external forward visual field of the seascape and navigation and steering displays in the pilot house. In addition to the primary steering control task, a subcritical speed tracking task provided a secondary surrogate for trimming the water speed of the craft. The results of helsmen's steering describing function measurements are presented, and some suggestions for their interpretation are offered. The likely steering loop closures comprise heading and lateral displacement for the course keeping task investigated. Also discussed is the manner in which these loop closures were implemented for automatic steering of the surface effect ship. Regardless of the influence of workload, steering technique, water speed and sea state, the helmsmen apparently adopted a disturbance regulation bandwidth of about 0.2 rad/sec for lateral displacement.

Objectification of steering feel around straight-line driving for vehicle/tyre design

NASA Astrophysics Data System (ADS)

Kim, Jungsik; Yoon, Yong-San

2015-02-01

This paper presents the objectification techniques for the assessment of steering feel including {on-centre} feel and steering response by measurement data. Here, new objective parameters are developed by considering not only the process by which the steering feel is evaluated subjectively but also by the ergonomic perceptive sensitivity of the driver. In order to validate such objective parameters, subjective tests are carried out by professional drivers. Objective measurements are also performed for several cars at a proving ground. The linear correlation coefficients between the subjective ratings and the objective parameters are calculated. As one of new objective parameters, steering wheel angle defined by ergonomic perception sensitivity shows high correlation with the subjective questionnaires of on-center responses. Newly defined steering torque curvature also shows high correlation with the subjective questionnaires of on-center effort. These correlation results conclude that the subjective assessment of steering feel can be successfully explained and objectified by means of the suggested objective parameters.

Creation of quantum steering by interaction with a common bath

NASA Astrophysics Data System (ADS)

Sun, Zhe; Xu, Xiao-Qiang; Liu, Bo

2018-05-01

By applying the hierarchy equation method, we computationally study the creation of quantum steering in a two-qubit system interacting with a common bosonic bath. The calculation does not adopt conventional approximate approaches, such as the Born, Markov, rotating-wave, and other perturbative approximations. Three kinds of quantum steering, i.e., Einstein-Podolsky-Rosen steering (EPRS), temporal steering (TS), and spatiotemporal steering (STS), are considered. Since the initial state of the two qubits is chosen as a product state, there does not exist EPRS at the beginning. During the evolution, we find that STS as well as EPRS are generated at the same time. An inversion relationship between STS and TS is revealed. By varying the system-bath coupling strength from weak to ultrastrong regimes, we find the nonmonotonic dependence of STS, TS, and EPRS on the coupling strength. It is interesting to study the dynamics of the three kinds of quantum steering by using an exactly numerical method, which is not considered in previous researches.

The effect of Electron Cyclotron Heating on density fluctuations at ion and electron scales in ITER Baseline Scenario discharges on the DIII-D tokamak

DOE PAGES

Marinoni, Alessandro; Pinsker, Robert I.; Porkolab, Miklos; ...

2017-08-01

Experiments simulating the ITER Baseline Scenario on the DIII-D tokamak show that torque-free pure electron heating, when coupled to plasmas subject to a net co-current beam torque, affects density fluctuations at electron scales on a sub-confinement time scale, whereas fluctuations at ion scales change only after profiles have evolved to a new stationary state. Modifications to the density fluctuations measured by the Phase Contrast Imaging diagnostic (PCI) are assessed by analyzing the time evolution following the switch-off of Electron Cyclotron Heating (ECH), thus going from mixed beam/ECH to pure neutral beam heating at fixed β N . Within 20 msmore » after turning off ECH, the intensity of fluctuations is observed to increase at frequencies higher than 200 kHz; in contrast, fluctuations at lower frequency are seen to decrease in intensity on a longer time scale, after other equilibrium quantities have evolved. Non-linear gyro-kinetic modeling at ion and electron scales scales suggest that, while the low frequency response of the diagnostic is consistent with the dominant ITG modes being weakened by the slow-time increase in flow shear, the high frequency response is due to prompt changes to the electron temperature profile that enhance electron modes and generate a larger heat flux and an inward particle pinch. Furthermore, these results suggest that electron heated regimes in ITER will feature multi-scale fluctuations that might affect fusion performance via modifications to profiles.« less

Validation of an Analytical Method for Determination of Benzo[a]pyrene Bread using QuEChERS Method by GC-MS

PubMed Central

Eslamizad, Samira; Yazdanpanah, Hassan; Javidnia, Katayon; Sadeghi, Ramezan; Bayat, Mitra; Shahabipour, Sara; Khalighian, Najmeh; Kobarfard, Farzad

2016-01-01

A fast and simple modified QuEChERS (quick, easy, cheap, rugged and safe) extraction method based on spiked calibration curves and direct sample introduction was developed for determination of Benzo [a] pyrene (BaP) in bread by gas chromatography-mass spectrometry single quadrupole selected ion monitoring (GC/MS-SQ-SIM). Sample preparation includes: extraction of BaP into acetone followed by cleanup with dispersive solid phase extraction. The use of spiked samples for constructing the calibration curve substantially reduced adverse matrix-related effects. The average recovery of BaP at 6 concentration levels was in range of 95-120%. The method was proved to be reproducible with relative standard deviation less than 14.5% for all of the concentration levels. The limit of detection and limit of quantification were 0.3 ng/g and 0.5 ng/g, respectively. Correlation coefficient of 0.997 was obtained for spiked calibration standards over the concentration range of 0.5-20 ng/g. To the best of our knowledge, this is the first time that a QuEChERS method is used for the analysis of BaP in breads. The developed method was used for determination of BaP in 29 traditional (Sangak) and industrial (Senan) bread samples collected from Tehran in 2014. These results showed that two Sangak samples were contaminated with BaP. Therefore, a comprehensive survey for monitoring of BaP in Sangak bread samples seems to be needed. This is the first report concerning contamination of bread samples with BaP in Iran. PMID:27642317

Determination of multiple pesticides in fruits and vegetables using a modified quick, easy, cheap, effective, rugged and safe method with magnetic nanoparticles and gas chromatography tandem mass spectrometry.

PubMed

Li, Yan-Fei; Qiao, Lu-Qin; Li, Fang-Wei; Ding, Yi; Yang, Zi-Jun; Wang, Ming-Lin

2014-09-26

Based on a modified quick, easy, cheap, effective, rugged and safe (QuEChERS) sample preparation method with Fe3O4 magnetic nanoparticles (MNPs) as the adsorbing material and gas chromatography-tandem mass spectrometry (GC-MS/MS) determination in multiple reaction monitoring (MRM) mode, we established a new method for the determination of multiple pesticides in vegetables and fruits. It was determined that bare MNPs have excellent function as adsorbent when purified, and it is better to be separated from the extract. The amount of MNPs influenced the clean-up performance and recoveries. To achieve the optimum performance of modified QuEChERS towards the target analytes, several parameters including the amount of the adsorbents and purification time were investigated. Under the optimum conditions, recoveries were evaluated in four representative matrices (tomato, cucumber, orange and apple) with the spiked concentrations of 10 μg kg(-1), 50 μg kg(-1)and 200 μg kg(-1) in all cases. The results showed that the recovery of 101 pesticides ranged between 71.5 and 111.7%, and the relative standard deviation was less than 10.5%. The optimum clean-up system improved the purification efficiency and simultaneously obtained satisfactory recoveries of multiple pesticides, including planar-ring pesticides. In short, the modified QuEChERS method in addition to MNPs used for removing impurities improved the speed of sample pre-treatment and exhibited an enhanced performance and purifying effect. Copyright © 2014 Elsevier B.V. All rights reserved.

Thermal control system of the Exoplanet Characterisation Observatory Payload: design and predictions

NASA Astrophysics Data System (ADS)

Morgante, G.; Terenzi, L.; Eccleston, P.; Bradshaw, T.; Crook, M.; Linder, M.; Hunt, T.; Winter, B.; Focardi, M.; Malaguti, G.; Micela, G.; Pace, E.; Tinetti, G.

2015-12-01

The Exoplanet Characterisation Observatory (EChO) is a space mission dedicated to investigate exoplanetary atmospheres by undertaking spectroscopy of transiting planets in a wide spectral region from the visible to the mid-InfraRed (IR). The high sensitivity and the long exposures required by the mission need an extremely stable thermo-mechanical platform. The instrument is passively cooled down to approximately 40 K, together with the telescope assembly, by a V-Groove based design that exploits the L2 orbit favourable thermal conditions. The visible and short-IR wavelength detectors are maintained at the operating temperature of 40 K by a dedicated radiator coupled to the cold space. The mid-IR channels, require a lower operating temperature and are cooled by an active refrigerator: a 28 K Neon Joule-Thomson (JT) cold end, fed by a mechanical compressor. Temperature stability is one of the challenging issues of the whole architecture: periodical perturbations must be controlled before they reach the sensitive units of the instrument. An efficient thermal control system is required: the design is based on a combination of passive and active solutions. In this paper we describe the thermal architecture of the payload with the main cryo-chain stages and their temperature control systems. The requirements that drive the design and the trade-offs needed to enable the EChO exciting science in a technically feasible payload design are discussed. Thermal modelling results and preliminary performance predictions in terms of steady state and transient conditions are also reported. This paper is presented on behalf of the EChO Consortium.

Characterization of two Streptomyces enzymes that convert ferulic acid to vanillin.

PubMed

Yang, Wenwen; Tang, Hongzhi; Ni, Jun; Wu, Qiulin; Hua, Dongliang; Tao, Fei; Xu, Ping

2013-01-01

Production of flavors from natural substrates by microbial transformation has become a growing and expanding field of study over the past decades. Vanillin, a major component of vanilla flavor, is a principal flavoring compound used worldwide. Streptomyces sp. strain V-1 is known to be one of the most promising microbial producers of natural vanillin from ferulic acid. Although identification of the microbial genes involved in the biotransformation of ferulic acid to vanillin has been previously reported, purification and detailed characterization of the corresponding enzymes with important functions have rarely been studied. In this study, we isolated and identified 2 critical genes, fcs and ech, encoding feruloyl-CoA synthetase and enoyl-CoA hydratase/aldolase, respectively, which are involved in the vanillin production from ferulic acid. Both genes were heterologously expressed in Escherichia coli, and the resting cell reactions for converting ferulic acid to vanillin were performed. The corresponding crucial enzymes, Fcs and Ech, were purified for the first time and the enzymatic activity of each purified protein was studied. Furthermore, Fcs was comprehensively characterized, at an optimal pH of 7.0 and temperature of 30°C. Kinetic constants for Fcs revealed the apparent Km, kcat, and Vmax values to be 0.35 mM, 67.7 s(-1), and 78.2 U mg(-1), respectively. The catalytic efficiency (kcat/Km) value of Fcs was 193.4 mM(-1) s(-1) for ferulic acid. The characterization of Fcs and Ech may be helpful for further research in the field of enzymatic engineering and metabolic regulation.

Development of a simple one-pot extraction method for various drugs and metabolites of forensic interest in blood by modifying the QuEChERS method.

PubMed

Matsuta, Shuntaro; Nakanishi, Keiko; Miki, Akihiro; Zaitsu, Kei; Shima, Noriaki; Kamata, Tooru; Nishioka, Hiroshi; Katagi, Munehiro; Tatsuno, Michiaki; Tsuboi, Kento; Tsuchihashi, Hitoshi; Suzuki, Koichi

2013-10-10

A rapid and convenient extraction method has been developed for the determination of various drugs and metabolites of forensic interest in blood by modifying the dispersive solid-phase extraction method "QuEChERS". The following 13 analytes with various chemical properties were used for the method development and its validation: amphetamine, methamphetamine, zolpidem, the carboxylate-form major metabolite of zolpidem M-1, flunitrazepam, 7-aminoflunitrazepam, phenobarbital, triazolam, α-hydroxytriazolam, brotizolam, α-hydroxybrotizolam, chlorpromazine, and promethazine. The modification of the QuEChERS method includes the use of relatively large amounts of inorganic salts in order to coagulate blood, which allows easy isolation of the organic extract phase. A combination of 100 mg anhydrous magnesium sulfate as a dehydrating agent, 50mg sodium chloride as a salting-out agent, and 500 μL acetonitrile containing 0.2% acetic acid as the organic solvent provided the optimum conditions for processing a 100 μL whole blood sample. The recoveries of the analytes spiked into whole blood at 0.5 μg/mL ranged between 59% and 93%. Although the addition of the graphitized carbon Envi-carb for cleanup decreased the recoveries of zolpidem and its carboxylate-form metabolite M-1, it was very effective in avoiding interferences by cholesterol. The present method can provide a rapid, effective, user-friendly, and relatively hygienic method for the simultaneous extraction of a wide range of drugs and metabolites in whole blood specimens. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Determination of pesticides in sewage sludge from an agro-food industry using QuEChERS extraction followed by analysis with liquid chromatography-tandem mass spectrometry.

PubMed

Ponce-Robles, Laura; Rivas, Gracia; Esteban, Belen; Oller, Isabel; Malato, Sixto; Agüera, Ana

2017-10-01

An analytical method was developed and validated for the determination of ten pesticides in sewage sludge coming from an agro-food industry. The method was based on the application of Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) extraction for solid sewage sludge and SPE extraction for sludge aqueous phase, followed by liquid chromatography (LC) coupled to hybrid quadrupole/linear ion trap mass spectrometry (QqLIT-MS). The QuEChERS method was reported 14 years ago and nowadays is mainly applied to the analysis of pesticides in food. More recent applications have been reported in other matrices as sewage sludge, but the complexity of the matrix makes necessary the optimization of the cleanup step to improve the efficiency of the analysis. With this aim, several dispersive solid-phase extraction cleanup sorbents were tested, choosing C18 + PSA as a d-SPE sorbent. The proposed method was satisfactorily validated for most compounds investigated, showing recoveries higher than 80% in most cases, with the only exception of prochloraz (71%) at low concentration level. Limits of quantification were lower than 40 ng l -1 in the aqueous phase and below 40 ng g -1 in the solid phase for the majority of the analytes. The method was applied to solid sludge and the sludge aqueous phase coming from an agro-food industry which processes fruits and vegetables. Graphical abstract Application of LC/MS/MS advanced analytical techniques for determination of pesticides contained in sewage sludge.

Characterization of Two Streptomyces Enzymes That Convert Ferulic Acid to Vanillin

PubMed Central

Yang, Wenwen; Tang, Hongzhi; Ni, Jun; Wu, Qiulin; Hua, Dongliang; Tao, Fei; Xu, Ping

2013-01-01

Production of flavors from natural substrates by microbial transformation has become a growing and expanding field of study over the past decades. Vanillin, a major component of vanilla flavor, is a principal flavoring compound used worldwide. Streptomyces sp. strain V-1 is known to be one of the most promising microbial producers of natural vanillin from ferulic acid. Although identification of the microbial genes involved in the biotransformation of ferulic acid to vanillin has been previously reported, purification and detailed characterization of the corresponding enzymes with important functions have rarely been studied. In this study, we isolated and identified 2 critical genes, fcs and ech, encoding feruloyl-CoA synthetase and enoyl-CoA hydratase/aldolase, respectively, which are involved in the vanillin production from ferulic acid. Both genes were heterologously expressed in Escherichia coli, and the resting cell reactions for converting ferulic acid to vanillin were performed. The corresponding crucial enzymes, Fcs and Ech, were purified for the first time and the enzymatic activity of each purified protein was studied. Furthermore, Fcs was comprehensively characterized, at an optimal pH of 7.0 and temperature of 30°C. Kinetic constants for Fcs revealed the apparent K m, k cat, and V max values to be 0.35 mM, 67.7 s−1, and 78.2 U mg−1, respectively. The catalytic efficiency (k cat/K m) value of Fcs was 193.4 mM−1 s−1 for ferulic acid. The characterization of Fcs and Ech may be helpful for further research in the field of enzymatic engineering and metabolic regulation. PMID:23840666

Reveal genes functionally associated with ACADS by a network study.

PubMed

Chen, Yulong; Su, Zhiguang

2015-09-15

Establishing a systematic network is aimed at finding essential human gene-gene/gene-disease pathway by means of network inter-connecting patterns and functional annotation analysis. In the present study, we have analyzed functional gene interactions of short-chain acyl-coenzyme A dehydrogenase gene (ACADS). ACADS plays a vital role in free fatty acid β-oxidation and regulates energy homeostasis. Modules of highly inter-connected genes in disease-specific ACADS network are derived by integrating gene function and protein interaction data. Among the 8 genes in ACADS web retrieved from both STRING and GeneMANIA, ACADS is effectively conjoined with 4 genes including HAHDA, HADHB, ECHS1 and ACAT1. The functional analysis is done via ontological briefing and candidate disease identification. We observed that the highly efficient-interlinked genes connected with ACADS are HAHDA, HADHB, ECHS1 and ACAT1. Interestingly, the ontological aspect of genes in the ACADS network reveals that ACADS, HAHDA and HADHB play equally vital roles in fatty acid metabolism. The gene ACAT1 together with ACADS indulges in ketone metabolism. Our computational gene web analysis also predicts potential candidate disease recognition, thus indicating the involvement of ACADS, HAHDA, HADHB, ECHS1 and ACAT1 not only with lipid metabolism but also with infant death syndrome, skeletal myopathy, acute hepatic encephalopathy, Reye-like syndrome, episodic ketosis, and metabolic acidosis. The current study presents a comprehensible layout of ACADS network, its functional strategies and candidate disease approach associated with ACADS network. Copyright © 2015 Elsevier B.V. All rights reserved.

9 CFR 78.6 - Steers and spayed heifers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS BRUCELLOSIS Restrictions on Interstate Movement of Cattle Because of Brucellosis § 78.6 Steers and spayed heifers. Steers...

9 CFR 78.6 - Steers and spayed heifers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS BRUCELLOSIS Restrictions on Interstate Movement of Cattle Because of Brucellosis § 78.6 Steers and spayed heifers. Steers...

9 CFR 78.6 - Steers and spayed heifers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS BRUCELLOSIS Restrictions on Interstate Movement of Cattle Because of Brucellosis § 78.6 Steers and spayed heifers. Steers...

9 CFR 78.6 - Steers and spayed heifers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS BRUCELLOSIS Restrictions on Interstate Movement of Cattle Because of Brucellosis § 78.6 Steers and spayed heifers. Steers...

9 CFR 78.6 - Steers and spayed heifers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS BRUCELLOSIS Restrictions on Interstate Movement of Cattle Because of Brucellosis § 78.6 Steers and spayed heifers. Steers...

Performance and welfare of steers housed on concrete slatted floors at fixed and dynamic (allometric based) space allowances.

PubMed

Keane, Michael P; McGee, Mark; O'Riordan, Edward G; Kelly, Alan K; Earley, Bernadette

2018-04-03

The objectives of the study were to determine whether allometric equations are suitable for estimating the space requirements of finishing beef cattle housed on concrete slatted floors (CSF) and to examine the effect of fixed and dynamic space allowances on the performance and welfare of these cattle. Continental crossbred steers [n = 120: mean initial live weight, 590 (SD 29.8) kg] were blocked by breed, weight, and age and assigned to 1 of 5 space allowance treatments (3 fixed and 2 dynamic) on CSF: 1) 2.0 m2 per animal, 2) 2.5 m2 per animal, 3) 3.0 m2 per animal, 4) Equation 1 (E1); y = 0.033w0.667, where y = m2 per animal and w = body weight, and 5) Equation 2 (E2); y = 0.048w0.667. The length of the feed face was 3.0 m for all treatments. Steers were offered grass silage and concentrates ad libitum. DMI was recorded weekly on a pen basis. Steers were weighed and dirt scored every 14 d. Blood samples were collected every 28 d, and analyzed for complete cell counts. Behavior was recorded using closed-circuit infrared cameras. Steers' hooves were inspected for lesions at the beginning of the study and post-slaughter. Slaughter weight and ADG were lowest, and feed conversion ratio (FCR) was poorest, for steers accommodated at 2.0 m2, and slaughter weight and ADG were greatest, and FCR was the best, for steers accommodated at E2 (P < 0.05); steers accommodated at 2.5 m2 were intermediate (P > 0.05) to those accommodated at 2.0 m2 and both 3.0 m2 and E1, whereas steers accommodated at 3.0 m2 and E1 were intermediate (P > 0.05) to 2.5 m2 and E2. Carcass weight of steers housed at 2.0 m2 was lower (P < 0.05) than all other treatments. Steers housed at 2.5 m2 had lower carcass weights (P < 0.05) than those with accommodated at E1 and E2, whereas the carcass weight of steers accommodated at 3.0 m2 was intermediate. Carcass fat scores and hide weights were lower (P < 0.05) in steers accommodated at 2.0 m2 than those housed at E2 with other treatments being intermediate. The number of steers lying at any one time and the number of steers observed grooming themselves was lower (P < 0.05) at 2.0 m2 than any other treatment. Dirt scores, hoof lesion number, and hematological measurements were not affected by treatment. It was concluded that 2.0 m2 per animal was an insufficient space allowance for housing finishing beef steers and that the equation y = 0.033w0.667 is sufficient for estimating the space required by finishing beef cattle housed on CSF.

Effect of yearling steer sequence grazing of perennial and annual forages in an integrated crop and livestock system on grazing performance, delayed feedlot entry, finishing performance, carcass measurements, and systems economics.

PubMed

Sentürklü, Songul; Landblom, Douglas G; Maddock, Robert; Petry, Tim; Wachenheim, Cheryl J; Paisley, Steve I

2018-06-04

In a 2-yr study, spring-born yearling steers (n = 144), previously grown to gain <0.454 kg·steer-1·d-1, following weaning in the fall, were stratified by BW and randomly assigned to three retained ownership rearing systems (three replications) in early May. Systems were 1) feedlot (FLT), 2) steers that grazed perennial crested wheatgrass (CWG) and native range (NR) before FLT entry (PST), and 3) steers that grazed perennial CWG and NR, and then field pea-barley (PBLY) mix and unharvested corn (UC) before FLT entry (ANN). The PST and ANN steers grazed 181 d before FLT entry. During grazing, ADG of ANN steers (1.01 ± SE kg/d) and PST steers (0.77 ± SE kg/d) did not differ (P = 0.31). But even though grazing cost per steer was greater (P = 0.002) for ANN vs. PST, grazing cost per kg of gain did not differ (P = 0.82). The ANN forage treatment improved LM area (P = 0.03) and percent i.m. fat (P = 0.001). The length of the finishing period was greatest (P < 0.001) for FLT (142 d), intermediate for PST (91 d), and least for ANN (66 d). Steer starting (P = 0.015) and ending finishing BW (P = 0.022) of ANN and PST were greater than FLT steers. Total FLT BW gain was greater for FLT steers (P = 0.017), but there were no treatment differences for ADG, (P = 0.16), DMI (P = 0.21), G: F (P = 0.82), and feed cost per kg of gain (P = 0.61). However, feed cost per steer was greatest for FLT ($578.30), least for ANN ($276.12), and intermediate for PST ($381.18) (P = 0.043). There was a tendency for FLT steer HCW to be less than ANN and PST, which did not differ (P = 0.076). There was no difference between treatments for LM area (P = 0.094), backfat depth (P = 0.28), marbling score (P = 0.18), USDA yield grade (P = 0.44), and quality grade (P = 0.47). Grazing steer net return ranged from an ANN system high of $9.09/steer to a FLT control system net loss of -$298 and a PST system that was slightly less than the ANN system (-$30.10). Ten-year (2003 to 2012) hedging and net return sensitivity analysis revealed that the FLT treatment underperformed 7 of 10 yr and futures hedging protection against catastrophic losses were profitable 40, 30, and 20% of the time period for ANN, PST, and FLT, respectively. Retained ownership from birth through slaughter coupled with delayed FLT entry grazing perennial and annual forages has the greatest profitability potential.

Influence of growing phase feed efficiency classification on finishing phase growth performance and carcass characteristics of beef steers fed different diet types.

PubMed

Russell, J R; Lundy, E L; Minton, N O; Sexten, W J; Kerley, M S; Hansen, S L

2016-07-01

A 5-yr study was conducted using 985 crossbred steers (464 kg [SD 32]) fed in 6 separate, replicated groups to determine the influence of growing phase (GP) feed efficiency (FE) classification and diet type on finishing phase (FP) FE of steers. During the GP at the University of Missouri, steers were fed either a whole shell corn-based diet (G-Corn; 528 steers) or a roughage-based diet (G-Rough; 457 steers) using GrowSafe feed bunks to measure DMI for 69 to 89 d. At the end of the GP, steers were ranked by residual feed intake (RFI) within diet, shipped to Iowa State University, and blocked into FP pens (5 to 6 steers/pen) by GP diet and RFI rank (upper, middle, or lower one-third). Steers were transitioned to either FP cracked corn- or byproduct-based diets and fed until 1.27 cm backfat was reached. After completion of the sixth group, average GP G:F within GP diet was calculated for each FP pen (168 total pens) using GP initial BW as a covariate (G-Corn: 0.207 [SD 0.038]; G-Rough: 0.185 [SD 0.036]). Pens were classified as highly feed efficient (HFE; >0.5 SD from the G:F mean; 58 pens), mid feed efficient (MFE; ±0.5 SD from the G:F mean; 60 pens), or lowly feed efficient (LFE; <0.5 SD from the G:F mean; 50 pens). Data were analyzed using PROC MIXED of SAS. Experimental unit was FP pen and the model included the fixed effects of GP diet, FE classification, FP diet, and the interactions. Group (1 to 6) was included as a fixed effect. There were no 3-way interactions ( ≥ 0.2) for any measured traits. Finishing phase G:F was not affected by any interactions ( ≥ 0.5) but was greater ( ≤ 0.03) for HFE versus MFE and LFE and greater ( = 0.02) for MFE versus LFE. Growing phase diet × FE classification effects were detected ( ≤ 0.01) for FP final BW (FBW), ADG, and DMI. Among G-Rough steers, HFE and MFE had greater ( ≤ 0.04) FBW and ADG than LFE, but among G-Corn steers, LFE had heavier ( = 0.03) FBW than HFE whereas ADG was unaffected ( ≥ 0.2) by FE classification. Dry matter intake was unaffected ( ≥ 0.3) by FE classification among G-Rough steers, but among G-Corn steers, LFE had greater ( ≤ 0.003) DMI than MFE and HFE. Overall, differences in FP G:F between FE classifications were driven by different factors depending on diet; ADG differed among roughage-grown steers and DMI differed among corn-grown steers. Ultimately, steers classified as HFE during the GP still had superior FE during the FP.

Effects of feeding corn modified wet distillers grain plus solubles co-ensiled with direct-cut forage on feedlot performance, carcass characteristics, and diet digestibility of finishing steers.

PubMed

Arias, R P; Unruh-Snyder, L J; Scholljegerdes, E J; Baird, A N; Johnson, K D; Buckmaster, D; Lemenager, R P; Lake, S L

2012-10-01

Two experiments were conducted to evaluate the effects of feeding corn modified wet distillers grain plus solubles (MWDGS) co-ensiled with direct-cut forage (DC) to beef steers, on feedlot performance and total tract digestibility. In Exp. 1, sixty-four crossbred Angus steers (n = 64; 329 ± 43 kg) were blocked by BW and randomly assigned to 1 of 4 dietary treatments: 1) corn-silage and soybean meal (CON), 2) DC co-ensiled with MWDGS (CO-EN), 3) haylage mixed with MWDGS at feeding (H+WDG), and 4) haylage mixed with dry distillers grains plus solubles at feeding (H+DDG). Steers were harvested when they reached an endpoint of 1.1 cm of 12th-rib back fat. In Exp. 2, four ruminally cannulated beef steers (initial BW = 556 ± 31 kg) were used in a 4 × 4 Latin square to evaluate digestibility of diets used in Exp. 1. Experimental periods were 14 d in length with 10 d for diet adaptation and 4 d for sample collection. Three linear orthogonal contrasts were used to compare effects of 1) CON vs. diets containing distillers grains (DGD), 2) CO-EN vs. diets where distillers grains were mixed at feeding (MIX), and 3) H+WDG vs. H+DDG. In Exp. 1, DMI was less (P < 0.001) for steers fed CON compared with those fed DGD and greatest (P < 0.001) for steers fed CO-EN compared with MIX. Corn-silage- and soybean-meal-fed steers had more days on feed than those fed DGD (P = 0.001). Body weight gain (P = 0.02) was greater for CO-EN compared with MIX. Fat thickness at the 12th and 13th ribs was greater (P = 0.03) for DGD steers compared with CON steers. Hot carcass weight was greater (P = 0.03) for steers fed CO-EN compared with those fed MIX. Steers fed CON resulted in greater marbling scores (P = 0.01) compared DGD-fed steers. Longissimus muscle area was greater (P = 0.01) for CON-fed steers compared with all other treatments. In Exp. 2, no differences (P > 0.10) in DM, OM, or N intakes were observed. Apparent total tract DM (P = 0.01) and N (P = 0.02) digestibility were greatest in steers fed CON compared with all others. Steers fed DGD had less (P = 0.02) rumen NH(3) concentrations compared with CON. The CON diet resulted in greater molar concentrations of VFA (P = 0.03) and decreased acetate to propionate ratio (P = 0.03) compared with all DGD. These data suggest that feeding MWDGS co-ensiled with direct-cut forage results in reduced diet digestibility but equal or greater feedlot performance and similar carcass and characteristics when compared with a corn diet supplemented with soybean meal and diets where MWDGS and DDGS were added at the mixer.

Continuous angle steering of an optically- controlled phased array antenna based on differential true time delay constituted by micro-optical components.

PubMed

Wang, Jian; Hou, Peipei; Cai, Haiwen; Sun, Jianfeng; Wang, Shunan; Wang, Lijuan; Yang, Fei

2015-04-06

We propose an optically controlled phased array antenna (PAA) based on differential true time delay constructed optical beamforming network (OBFN). Differential true time delay is realized by stack integrated micro-optical components. Optically-controlled angle steering of radio frequency (RF) beams are realized and demonstrated by this configuration. Experimental results demonstrate that OBFN based PAA can accomplish RF-independent broadband beam steering without beam squint effect and can achieve continuous angle steering. In addition, multi-beams for different steering angles are acquired synchronously.

Effects of roughage inclusion and particle size on performance and rumination behavior of finishing beef steers.

PubMed

Gentry, W W; Weiss, C P; Meredith, C M; McCollum, F T; Cole, N A; Jennings, J S

2016-11-01

Roughage is typically mechanically processed to increase digestibility and improve handling and mixing characteristics in beef cattle finishing diets. Roughage is fed to promote ruminal health and decrease digestive upset, but inclusion in finishing diets is limited due to the cost per unit of energy. Rumination behavior may be a means to standardize roughage in beef cattle finishing diets, and increasing particle size of roughage may allow a decrease in roughage inclusion without sacrificing animal performance. Therefore, the objectives of this study were to quantify rumination time for a finishing beef animal and to evaluate the effects of corn stalk (CS) inclusion rate and particle size on rumination behavior, animal performance, and carcass characteristics. Fifty-one individually fed steers (385 ± 3.6 kg initial BW) were used in a randomized complete block design feeding study. Corn stalks were passed through a tub grinder equipped with a 7.62-cm screen once to generate long-grind CS (LG-CS) or twice to generate short-grind CS (SG-CS). Dietary treatments were based on steam-flaked corn and included, on a DM basis, 30% wet corn gluten feed (WCGF) with 5% SG-CS (5SG), 30% WCGF with 5% LG-CS (5LG), and 25% WCGF with 10% SG-CS (10SG). The Penn State Particle Separator was used to separate ingredients and treatment diets and to estimate physically effective NDF (peNDF). On d 70, each steer was fitted with a collar (HR Tag; SCR Dairy, Netanya, Isreal), which continuously measured rumination minutes via a sensory microphone. Long-grind CS contained more ( < 0.01) peNDF than SG-CS, and the 10SG diet contained more ( = 0.03) peNDF than the 5LG and 5SG diets. Dry matter intake was greatest ( = 0.03) for steers consuming 5LG and least for steers consuming 10SG, with cattle consuming 5SG being intermediate. Carcass-adjusted ADG and G:F were greatest ( ≤ 0.03) for steers consuming 5LG and 5SG compared with steers consuming 10SG. Hot carcass weight tended ( = 0.10) to be greatest for steers consuming 5LG and least for steers consuming 10SG, with steers consuming 5SG being intermediate. Dressing percent was greater ( = 0.01) for steers consuming 5LG and 5SG than for steers consuming 10SG. A significant interaction ( < 0.01) occurred for rumination minutes × day. Rumination (min/day) were greatest ( = 0.01) for steers consuming 10SG followed by steers consuming 5LG and was lowest for steers consuming 5SG. Increasing particle size of roughage may be a means to decrease roughage inclusion rate while maintaining rumination and performance.

CCCT - Patient Advocate Steering Committee

Cancer.gov

The Patient Advocate Steering Committee (PASC) works to ensure advocates involved with the Scientific Steering Committees (SSCs) are completely integrated in the development, implementation, and monitoring of clinical trials within those groups.

Growth implants reduced tenderness of steaks from steers and heifers with different genetic potentials for growth and marbling.

PubMed

Boles, J A; Boss, D L; Neary, K I; Davis, K C; Tess, M W

2009-01-01

The objective of this study was to evaluate the effect of growth implants on the carcass characteristics and tenderness of steers and heifers with different genetic potentials for growth, lean meat yield production, and marbling. Two experiments were conducted. Experiment 1 evaluated Angus steers sired by bulls with high EPD for retail product yield or marbling. Implant treatment was imposed randomly within sire groups. Loins (Institutional Meat Purchasing Specifications 180) were collected from each carcass and cut into three 2.54-cm steaks aged for 7, 14 and 21 d to evaluate tenderness. The second experiment evaluated steers and heifers of British and Continental breed descent. Steers and heifers were slaughtered after 120 d on feed. Loin sections were collected, and one 2.54-cm steak aged 7 d was used for tenderness analysis. When implants were used in Angus steers, HCW and LM area increased, whereas internal fat and marbling decreased (P < 0.01). In Angus steers, sire type did not affect shear force values of steaks; however, implant use significantly increased shear force values (P < 0.01). Carcasses from cattle of Continental breed descent were significantly heavier than carcasses of British breed descent with larger LM area, slightly less fat, and a reduced yield grade (P < 0.01). Also, steer carcasses were heavier than heifer carcasses with larger LM (P < 0.05), but no effect of sex on fat depth, internal fat, yield grade or marbling was observed. No significant interactions were seen between growth implant and breed or between growth implant and sex for shear force values. Shear force values were significantly less for steaks from steers and heifers of British decent compared with steers and heifers of Continental descent (P < 0.01). Steaks from implanted steers and heifers had significantly (P < 0.01) greater shear force values than steaks from steers and heifers not implanted. Use of growth implants in growing cattle resulted in significantly heavier carcass weights, larger LM area, and reduced internal fat. However, implant use also reduced the amount of marbling along with contributing to reduced tenderness. Complicating the tenderness issue is the increased shear force values reported for heifers as well as steers of Continental breed descent. Use of implants may contribute to tenderness variability because of different animal responses to implants.

A new generation of IC based beam steering devices for free-space optical communication

NASA Astrophysics Data System (ADS)

Bedi, Vijit

Free Space Optical (FSO) communication has tremendously advanced within the last decade to meet the ever increasing demand for higher communication bandwidth. Advancement in laser technology since its invention in the 1960's [1] attracted them to be the dominant source in FSO communication modules. The future of FSO systems lay in implementing semiconductor lasers due to their small size, power efficiency and mass fabrication abilities. In the near future, these systems are very likely to be used in space and ground based applications and revolutionary beam steering technologies will be required for distant communications in free-space. The highly directional characteristic inherent to a laser beam challenges and calls for new beam pointing and steering technologies for such type of communication. In this dissertation, research is done on a novel FSO communication device based on semiconductor lasers for high bandwidth communication. The "Fly eye transceiver" is an extremely wide steering bandwidth, completely non-mechanical FSO laser communication device primarily designed to replace traditional mechanical beam steering optical systems. This non-mechanical FSO device possesses a full spherical steering range and a very high tracking bandwidth. Inspired by the evolutionary model of a fly's eye, the full spherical steering range is assured by electronically controlled switching of its sub-eyes. Non mechanical technologies used in the past for beam steering such as acousto-optic Bragg cells, liquid crystal arrays or piezoelectric elements offer the wide steering bandwidth and fast response time, but are limited in their angular steering range. Mechanical gimbals offer a much greater steering range but face a much slower response time or steering bandwidth problem and often require intelligent adaptive controls with bulky driver amplifiers to feed their actuators. As a solution to feed both the fast and full spherical steering, the Fly-eye transceiver is studied as part of my PhD work. The design tool created for the research of the fly eye is then used to study different applications that may be implemented with the concept. Research is done on the mathematical feasibility, modeling, design, application of the technology, and its characterization in a simulation environment. In addition, effects of atmospheric turbulence on beam propagation in free space, and applying data security using optical encryption are also researched.

46 CFR 35.20-10 - Steering gear test-T/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 1 2012-10-01 2012-10-01 false Steering gear test-T/ALL. 35.20-10 Section 35.20-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS OPERATIONS Navigation § 35.20-10 Steering gear test—T/ALL. On all tankships making voyages of more than 48 hours' duration, the entire steering gear, the whistle, the means of...

Additive effects of growth promoting technologies on performance of grazing steers and economics of the wheat pasture enterprise.

PubMed

Beck, P; Hess, T; Hubbell, D; Hufstedler, G D; Fieser, B; Caldwell, J

2014-03-01

This research was designed to evaluate the effect of monensin (Elanco Animal Health, Greenfield, IN) supplementation via mineral or pressed protein block with or without a growth-promoting implant on performance of steers grazing wheat pasture in Arkansas over 2 yr. Preconditioned steers (n = 360, BW = 238 ± 5.1 kg) grazed 15 1.6-ha wheat pastures in the fall (n = 60 steers each fall, stocking rate of 2.5 steers/ha) or 30 0.8-ha wheat pastures in the spring (n = 120 steers each spring, stocking rate of 5 steers/ha). Steers in each pasture were given free-choice access to nonmedicated mineral (CNTRL; MoorMan's WeatherMaster Range Minerals A 646AAA; ADM Alliance Nutrition, Inc., Quincy, IL), or were supplemented with monensin (Elanco Animal Health, Greenfield, IN) via mineral containing 1.78 g monensin/kg (RMIN; MoorMan's Grower Mineral RU-1620 590AR; ADM Alliance Nutrition, Inc.), or pressed protein block containing 0.33 g monensin/kg (RBLCK; MoorMan's Mintrate Blonde Block RU; ADM Alliance Nutrition, Inc.). Additionally, one-half of the steers in each pasture were implanted (IMPL) with 40 mg trenbolone acetate and 8 mg estradiol (Component TE-G with Tylan; Elanco Animal Health). There was no interaction (P ≥ 0.71) between supplement treatment and growth-promoting implants, and ADG for RMIN and RBLCK were increased (P < 0.01) over CNTRL by 0.07 to 0.09 kg/d, respectively. Implanting steers with Component TE-G increased (P < 0.01) ADG by 0.14 kg/d. The combination of these growth-promoting technologies are a cost-effective means of increasing beef production by 22% without increasing level of supplementation or pasture acreage. Utilizing ionophores and implants together for wheat pasture stocker cattle decreased cost of gain by 26%. Utilizing both IMPL and monensin increased net return by $30 to $54/steer for RMIN or $18 to $43/steer for RBLCK compared with UNIMPL CNTRL at Low and High values of BW gain, respectively.

Effects of Chicory/Perennial Ryegrass Swards Compared with Perennial Ryegrass Swards on the Performance and Carcass Quality of Grazing Beef Steers

PubMed Central

Marley, Christina L.; Fychan, Rhun; Davies, John W.; Scollan, Nigel D.; Richardson, R. Ian; Theobald, Vince J.; Genever, Elizabeth; Forbes, Andy B.; Sanderson, Ruth

2014-01-01

An experiment investigated whether the inclusion of chicory (Cichorium intybus) in swards grazed by beef steers altered their performance, carcass characteristics or parasitism when compared to steers grazing perennial ryegrass (Lolium perenne). Triplicate 2-ha plots were established with a chicory/ryegrass mix or ryegrass control. Forty-eight Belgian Blue-cross steers were used in the first grazing season and a core group (n = 36) were retained for finishing in the second grazing season. The experiment comprised of a standardisation and measurement period. During standardisation, steers grazed a ryegrass/white clover pasture as one group. Animals were allocated to treatment on the basis of liveweight, body condition and faecal egg counts (FEC) determined 7 days prior to the measurement period. The measurement period ran from 25 May until 28 September 2010 and 12 April until 11 October 2011in the first and second grazing year. Steers were weighed every 14 days at pasture or 28 days during housing. In the first grazing year, faecal samples were collected for FEC and parasite cultures. At the end of the first grazing year, individual blood samples were taken to determine O. ostertagi antibody and plasma pepsinogen levels. During winter, animals were housed as one group and fed silage. In the second grazing year, steers were slaughtered when deemed to reach fat class 3. Data on steer performance showed no differences in daily live-weight gain which averaged 1.04 kg/day. The conformation, fat grade and killing out proportion of beef steers grazing chicory/ryegrass or ryegrass were not found to differ. No differences in FEC, O. ostertagi antibody or plasma pepsinogen levels of beef steers grazing either chicory/ryegrass or ryegrass were observed. Overall, there were no detrimental effects of including chicory in swards grazed by beef cattle on their performance, carcass characteristics or helminth parasitism, when compared with steers grazing ryegrass. PMID:24489708

Characterization of different biological types of steers (cycle IV): wholesale, subprimal, and retail product yields.

PubMed

Wheeler, T L; Cundiff, L V; Koch, R M; Dikeman, M E; Crouse, J D

1997-09-01

Carcass cut-out yields of 888 steers obtained from mating Hereford and Angus cows to Hereford or Angus (HA), Charolais (Ch), Gelbvieh (Gb), Pinzgauer (Pz), Shorthorn (Sh), Galloway (Gw), Longhorn (Lh), Nellore (Ne), Piedmontese (Pm), and Salers (Sa) sires were compared. Data were evaluated at constant age (426 d), carcass weight (324 kg), fat thickness (1.2 cm), fat trim percentage (23%), and marbling (Small(00)) end points. Piedmontese-sired steers excelled in total retail product and fat trim percentages at all slaughter end points except at the 23% fat trim end point. At an age end point, percentage of retail product was greater in steers sired by Continental European breeds (Gb, Ch, Sa, Pz; 63.3 to 65.5% at 0 cm trim) than in steers sired by British breeds (Sh, HA; 60.1 to 61.0%). Piedmontese-sired steers, which were expected to carry one copy of a major gene for muscle hypertrophy, had the highest (P < .05) retail product yields at an age end point (69.7%). At an age end point, although carcass weights were significantly heavier (P < .05) for Charolais-sired steers than for Piedmontese-sired steers, lean growth rate, as reflected by totally trimmed retail product at 426 d, was similar (P > .05) for Piedmontese and Charolais-sired steers. Differences among sire breeds were small for retail product percentage at marbling, fat thickness, and fat trim end points. Ranking of sire breeds for age-constant weight of retail product was as follows: Ch, Pm, Gb, Sa, Ne, Pz, HA, Sh, Gw, and Lh. Sire breed differences in wholesale and subprimal cut yields were similar to total retail product differences. Piedmontese-sired steers produced the most muscular, leanest, and highest-yielding carcasses, and HA- and Sh-sired steers produced the fattest, lowest-yielding carcasses.

Beam Steering Devices Reduce Payload Weight

NASA Technical Reports Server (NTRS)

2012-01-01

Scientists have long been able to shift the direction of a laser beam, steering it toward a target, but often the strength and focus of the light is altered. For precision applications, where the quality of the beam cannot be compromised, scientists have typically turned to mechanical steering methods, redirecting the source of the beam by swinging the entire laser apparatus toward the target. Just as the mechanical methods used for turning cars has evolved into simpler, lighter, power steering methods, so has the means by which researchers can direct lasers. Some of the typical contraptions used to redirect lasers are large and bulky, relying on steering gimbals pivoted, rotating supports to shift the device toward its intended target. These devices, some as large and awkward as a piece of heavy luggage, are subject to the same issues confronted by mechanical parts: Components rub, wear out, and get stuck. The poor reliability and bulk not to mention the power requirements to run one of the machines have made mechanical beam steering components less than ideal for use in applications where weight, bulk, and maneuverability are prime concerns, such as on an unmanned aerial vehicle (UAV) or a microscope. The solution to developing reliable, lighter weight, nonmechanical steering methods to replace the hefty steering boxes was to think outside the box, and a NASA research partner did just that by developing a new beam steering method that bends and redirects the beam, as opposed to shifting the entire apparatus. The benefits include lower power requirements, a smaller footprint, reduced weight, and better control and flexibility in steering capabilities. Such benefits are realized without sacrificing aperture size, efficiency, or scanning range, and can be applied to myriad uses: propulsion systems, structures, radiation protection systems, and landing systems.

Carcass characteristics, fatty acid composition, and meat quality of Criollo Argentino and Braford steers raised on forage in a semi-tropical region of Argentina.

PubMed

Orellana, Carlos; Peña, F; García, A; Perea, J; Martos, J; Domenech, V; Acero, R

2009-01-01

The purpose of this study was to characterize and compare the carcass characteristics, cholesterol concentration, fatty acid composition of intramuscular fat and subcutaneous fat, and meat quality of Criollo Argentino and Braford steers reared in an extensive system, without supplementation, and slaughtered at approximately 400kg live weight. The Braford steers had greater (P<0.05) carcass weight, yield, conformation score, marbling degree, fat thickness and fatness score than Criollo Argentino steers. The tissue composition of the 10th rib was: 68.1% vs. 63.6% muscle, 23.9% vs. 20.4% bone and 8.2% vs. 16.3% fat for the Criollo Argentino and Braford breeds, respectively. The meat of Longissimus muscle from Braford steers was lighter, redder, yellower and more tender than that from Criollo Argentino steers. The meat of Longissimus muscle from Braford steers had a higher fat content, similar protein and ash contents and a lower (P⩽0.001) cholesterol concentration than that from Criollo Argentino steers. The subcutaneous depot was the most saturated, while the intramuscular fat had the most polyunsaturated fatty acids. Intramuscular fat showed the highest ∑h fatty acids, and PUFA/SFA and n-6/n-3 ratios and for MUFA/SFA, 16:0/18:0 and h/H ratios were not significantly different between adipose tissue depots. The influence of breed on the fatty acid profile varies among adipose tissues. In general, both intramuscular fat and subcutaneous fat from Criollo steers contained more unsaturated fatty acids and less saturated fatty acids, than did fat from Braford steers.

Collision-model approach to steering of an open driven qubit

NASA Astrophysics Data System (ADS)

Beyer, Konstantin; Luoma, Kimmo; Strunz, Walter T.

2018-03-01

We investigate quantum steering of an open quantum system by measurements on its environment in the framework of collision models. As an example we consider a coherently driven qubit dissipatively coupled to a bath. We construct local nonadaptive and adaptive as well as nonlocal measurement scenarios specifying explicitly the measured observable on the environment. Our approach shows transparently how the conditional evolution of the open system depends on the type of the measurement scenario and the measured observables. These can then be optimized for steering. The nonlocal measurement scenario leads to maximal violation of the used steering inequality at zero temperature. Further, we investigate the robustness of the constructed scenarios against thermal noise. We find generally that steering becomes harder at higher temperatures. Surprisingly, the system can be steered even when bipartite entanglement between the system and individual subenvironments vanishes.

Laser-phased-array beam steering based on crystal fiber

NASA Astrophysics Data System (ADS)

Yang, Deng-cai; Zhao, Si-si; Wang, Da-yong; Wang, Zhi-yong; Zhang, Xiao-fei

2011-06-01

Laser-phased-array system provides an elegant means for achieving the inertial-free, high-resolution, rapid and random beam steering. In laser-phased-array system, phase controlling is the most important factor that impacts the system performance. A novel scheme is provided in this paper, the beam steering is accomplished by using crystal fiber array, the difference length between adjacent fiber is fixed. The phase difference between adjacent fiber decides the direction of the output beam. When the wavelength of the input fiber laser is tuned, the phase difference between the adjacent elements has changed. Therefore, the laser beam direction has changed and the beam steering has been accomplished. In this article, based on the proposed scheme, the steering angle of the laser beam is calculated and analyzed theoretically. Moreover, the far-field steering beam quality is discussed.

Daidzein enhances intramuscular fat deposition and improves meat quality in finishing steers

PubMed Central

Zhao, Xiang-Hui; Yang, Zhu-Qing; Bao, Lin-Bin; Wang, Can-Yu; -Zhou, Shan; Gong, Jian-Ming; Fu, Chuan-Bian; Xu, Lan-Jiao; Liu, Chan-Juan

2015-01-01

An experiment was conducted to determine the effects of soy isoflavone daidzein on carcass characteristics, fat deposition, meat quality, and blood metabolites in finishing steers. Fourteen crossbred steers were used in a 120-d finishing study. These steers were stratified by weight into groups and randomly allotted by group to one of two dietary treatments: (1) control and (2) daidzein (500 mg/kg concentrate). The steers were fed a 90% concentrate diet. Supplemental daidzein did not affect slaughter weight, hot carcass weight, and dressing percentage, but tended to reduce fat proportion (not including intramuscular fat) in carcass and backfat thickness of steers. The carcass bone proportion was greater in steers fed daidzein diets than those fed control diets. Daidzein supplementation reduced pH at 24 h after slaughtered and moisture content and increased isocitrate dehydrogenase activity, fat content (16.28% and 7.94%), marbling score (5.29 and 3.36), redness (a*), and chroma (C*) values in longissimus muscle relative to control treatment. The concentrations of blood metabolites including glucose, blood urea nitrogen, triglyceride, total cholesterol, non-esterified fatty acid, high-density lipoprotein cholesterol (HDL-C), and low-density lipoprotein cholesterol (LDL-C) were all lower in steers fed daidzein diets than those fed control diets. Current results suggest that supplemental daidzein can affect lipid metabolism, increase intramuscular fat content and marbling score, and improve meat quality in finishing steers. Daidzein should be a promising feed additive for production of high-quality beef meat. PMID:25526906

Mechanical Mixer for Rudder/Braking Wedge

NASA Technical Reports Server (NTRS)

Grimm, D.

1985-01-01

Right and left rudder panels moved separately. Mechanical mixer enables panels of two-panel rudder to rotate in same direction for steering or in opposite directions for dynamic braking. Steering and braking inputs separate so any combination of steering and braking motions executed simultaneously. Developed for aerodynamic braking of Space Shuttle orbiter, steering/braking drive train and rudder arrangement used for similar purposes on aircraft, thereby reducing sizes of thrust reversers.

Modeling of electronic power steering system for IKCO SAMAND vehicle and investigating on its performance via CARSIM software

NASA Astrophysics Data System (ADS)

Haghgoo, Esmail; Zamani, Mohammad; Sharbati, Ali

2017-02-01

The point of this article is introducing the usage of electronic power steering (ESP) system in IKCO SAMAND vehicle and investigating on it's benefit's. Also the operation of electronic steering system and it's performance in IKCO SAMAND vehicle have been described. The optimization of IC engine efficiency and it's fuel consumption have been simulated via ADVISOR software used in MATLAB software. Usually, mechanical steering systems and hydraulic steering systems are producing inside IRAN that the mechanical types have not accepted because of it's too many disadvantages. The hydraulic steering systems, that have been replaced with mechanical types, indeed have the same features with mechanical types but with a difference which they have a hydraulic booster to facilitate the rotation of steering wheel. Beside advantages in hydraulic systems, they are some disadvantages in this system that one of the most important of them is reducing the output power of engine. To restore this power dissipated, we use ESP systems. In this article output diagrams given by software, are showing that IKCO SAMAND vehicle which equipped with ESP system, exerts less torque and power on steering wheel. This improves the safety of driver and also performance of the vehicle at high speeds and reduces fuel consumption beside increasing the efficiency of IC engine.

Design of an actively controlled steerable needle with tendon actuation and FBG-based shape sensing.

PubMed

van de Berg, Nick J; Dankelman, Jenny; van den Dobbelsteen, John J

2015-06-01

This work presents a new steerable needle to facilitate active steering toward predefined target locations. It focuses on mechanical aspects and design choices in relation to the observed response in a tissue phantom. Tip steering with two rotational degrees of freedom was achieved by a tendon actuated ball joint mechanism. During insertion, the flexible cannula bends as a result of asymmetric tip-tissue interaction forces. The stylet was equipped with fiber Bragg gratings to measure the needle shape and tip position during use. A PI-controller was implemented to facilitate steering to predefined targets. During the validation study, nine targets were defined at a depth of 100 mm below the gelatin surface. One was located below the insertion point, the others at a radial offset of 30 mm in each of the eight principle steering directions. Per location, six repetitions were performed. The targeting accuracy was 6.2 ± 1.4 mm (mean ± std). The steering precision was 2.6 ± 1.1 mm. The ability to steer with this new needle steering approach is presented and the mechanical characteristics are discussed for this representative subset of steering directions. Copyright © 2015 IPEM. Published by Elsevier Ltd. All rights reserved.

Factors influencing intermuscular fat and other measures of beef chuck composition.

PubMed

Christensen, K L; Johnson, D D; West, R L; Hargrove, D D; Marshall, T T; Rogers, A L

1991-11-01

Carcasses from 59 steers produced from the mating of Braford, Simbrah, Senepol, and Simmental bulls to Brahman- and Romana Red-sired cows and Brahman bulls mated to Angus cows were used in this study. Effects of sire breed and feeding calves vs yearlings on fat depots in the chuck, when steers were fed to 1.0 cm external fat, were determined. Breed of sire and feeding calves vs yearlings had no effect (P greater than .05) on percentage of intermuscular fat. However, carcasses from Braford-sired steers had a higher (P less than .05) percentage of dissectable subcutaneous fat on the chuck than did those from other breed groups. Carcasses from Simmental-sired steers were superior (P less than .05) to those from Braford-sired steers in USDA yield grade and had a higher average marbling score (P less than .05) than the Simbrah-sired group. Estimated kidney, pelvic, and heart (KPH) fat was higher (P less than .05) in carcasses from Brahman-, Simbrah-, and Senepol-sired steers than in Braford-sired steers. Steers fed as calves had higher percentages (P less than .05) of KPH fat and major chuck muscles than did those fed as yearlings. The best single predictor of percentage of intermuscular fat within the chuck was adjusted fat over the ribeye (R2 = .46).

Effect of castration on carcass quality and differential gene expression of longissimus muscle between steer and bull.

PubMed

Zhou, Zheng-Kui; Gao, Xue; Li, Jun-Ya; Chen, Jin-Bao; Xu, Shang-Zhong

2011-11-01

The effect of castration on carcass quality was investigated by ten Chinese Simmental calves. Five calves were castrated randomly at 2 months old and the others were retained as normal intact bulls. All animals were slaughtered at 22 months old. The results showed that bulls carcass had higher weight (P < 0.05), dressing percentages and bigger longissimus muscle areas (P < 0.05) than steers. But steer meat had lower shear force values and was fatter (P < 0.05) than bull. Furthermore, in order to discover genes that were involved in determining steer meat quality, we compared related candidate gene expression in longissimus muscle between steer (tester) and bull (driver) using suppressive subtractive hybridization. Ten genes were identified as preferentially expressed in longissimus muscle of steer. The expression of four selected differentially expressed genes was confirmed by quantitative real-time PCR. Overall, a 1.96, 2.41, 2.89, 2.41-fold increase in expression level was observed in steer compared with bull for actin, gamma 2, smooth muscle, tropomyosin-2, insulin like growth factor 1 and hormone-sensitive lipase, respectively. These results implied that these differentially expressed genes could play an important role in the regulation of steer meat quality.

Directional control-response compatibility of joystick steered shuttle cars.

PubMed

Burgess-Limerick, Robin; Zupanc, Christine M; Wallis, Guy

2012-01-01

Shuttle cars are an unusual class of vehicle operated in underground coal mines, sometimes in close proximity to pedestrians and steering errors may have very serious consequences. A directional control-response incompatibility has previously been described in shuttle cars which are controlled using a steering wheel oriented perpendicular to the direction of travel. Some other shuttle car operators are seated perpendicular to the direction of travel and steer the car via a seat mounted joystick. A virtual simulation was utilised to determine whether the steering arrangement in these vehicles maintains directional control-response compatibility. Twenty-four participants were randomly assigned to either a condition corresponding to this design (consistent direction), or a condition in which the directional steering response was reversed while driving in-bye (visual field compatible). Significantly less accurate steering performance was exhibited by the consistent direction group during the in-bye trials only. Shuttle cars which provide the joystick steering mechanism described here require operators to accommodate alternating compatible and incompatible directional control-response relationships with each change of car direction. A virtual simulation of an underground coal shuttle car demonstrates that the design incorporates a directional control-response incompatibility when driving the vehicle in one direction. This design increases the probability of operator error, with potential adverse safety and productivity consequences.

Stereo-based Collision Avoidance System for Urban Traffic

NASA Astrophysics Data System (ADS)

Moriya, Takashi; Ishikawa, Naoto; Sasaki, Kazuyuki; Nakajima, Masato

2002-11-01

Numerous car accidents occur on urban road. However, researches done so far on driving assistance are subjecting highways whose environment is relatively simple and easy to handle, and new approach for urban settings is required. Our purpose is to extend its support to the following conditions in city traffic: the presence of obstacles such as pedestrians and telephone poles; the lane mark is not always drawn on a road; drivers may lack the sense of awareness of the lane mark. We propose a collision avoidance system, which can be applied to both highways and urban traffic environment. In our system, stereo cameras are set in front of a vehicle and the captured images are processed through a computer. We create a Projected Disparity Map (PDM) from stereo image pair, which is a disparity histogram taken along ordinate direction of obtained disparity image. When there is an obstacle in front, we can detect it by finding a peak appeared in the PDM. With a speed meter and a steering sensor, the stop distance and the radius of curvature of the self-vehicle are calculated, in order to set the observation-required area, which does not depend on lane marks, within a PDM. A danger level will be computed from the distance and the relative speed to the closest approaching object detected within the observation-required area. The method has been tested in urban traffic scenes and has shown to be effective for judging dangerous situation, and gives proper alarm to a driver.

Micromachined actuators/sensors for intratubular positioning/steering

DOEpatents

Lee, Abraham P.; Krulevitch, Peter A.; Northrup, M. Allen; Trevino, Jimmy C.

1998-01-01

Micromachined thin film cantilever actuators having means for individually controlling the deflection of the cantilevers, valve members, and rudders for steering same through blood vessels, or positioning same within a blood vessel, for example. Such cantilever actuators include tactile sensor arrays mounted on a catheter or guide wire tip for navigation and tissues identification, shape-memory alloy film based catheter/guide wire steering mechanisms, and rudder-based steering devices that allow the selective actuation of rudders that use the flowing blood itself to help direct the catheter direction through the blood vessel. While particularly adapted for medical applications, these cantilever actuators can be used for steering through piping and tubing systems.

Integrated phased array for wide-angle beam steering.

PubMed

Yaacobi, Ami; Sun, Jie; Moresco, Michele; Leake, Gerald; Coolbaugh, Douglas; Watts, Michael R

2014-08-01

We demonstrate an on-chip optical phased array fabricated in a CMOS compatible process with continuous, fast (100 kHz), wide-angle (51°) beam-steering suitable for applications such as low-cost LIDAR systems. The device demonstrates the largest (51°) beam-steering and beam-spacing to date while providing the ability to steer continuously over the entire range. Continuous steering is enabled by a cascaded phase shifting architecture utilizing, low power and small footprint, thermo-optic phase shifters. We demonstrate these results in the telecom C-band, but the same design can easily be adjusted for any wavelength between 1.2 and 3.5 μm.

46 CFR 169.623 - Power-driven steering systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... systems must have means to be brought into operation from a dead ship condition, without external aid. The... steering systems from the main steering control location must include, as applicable— (1) Control of any...

46 CFR 169.623 - Power-driven steering systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... systems must have means to be brought into operation from a dead ship condition, without external aid. The... steering systems from the main steering control location must include, as applicable— (1) Control of any...

46 CFR 169.623 - Power-driven steering systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... systems must have means to be brought into operation from a dead ship condition, without external aid. The... steering systems from the main steering control location must include, as applicable— (1) Control of any...

Influence of genotype and diet on steer performance, manure odor, and carriage of pathogenic and other fecal bacteria. I. Animal performance.

PubMed

Ferrell, C L; Berry, E D; Freetly, H C; Miller, D N

2006-09-01

Although Brahman crosses constitute a large portion of US beef cattle, little information is available on their response to diverse feed resources compared with Bos taurus steers. Thus, the objectives were to evaluate genotype and diet effects on steer performance during the growing period and subsequent response to a high grain diet during the finishing period. Fifty-one steers [0 (15), 1/4 (20), 1/2 (7), and 3/4 Brahman (9), with the remaining proportion being MARC III] were allotted to 8 pens. Beginning on December 2, steers were individually fed chopped bromegrass hay (n = 26; DM = 85%, CP = 9.5%, ME = 2.19 Mcal/kg) or a corn silage-based diet (n = 25; DM = 51%, CP = 11.9%, ME = 2.75 Mcal/kg) for 119 d. All steers were then fed a high corn diet (DM = 79%, CP = 11.7%, ME = 3.08 Mcal/kg) to a target BW of 560 kg (176 d). Data were analyzed by ANOVA, with genotype, growing diet, and the 2-way interaction included. The interaction was not significant (P > 0.25). The MARC III and 1/2 Brahman steers weighed more (P < 0.01) than 1/4 or 3/4 Brahman steers initially and at the end of the growing period. Weight of bromegrass-fed (325 kg) steers was less than that of corn silage-fed (384 kg) steers at the end of the growing period. Steer ADG and intake of DM, CP, and ME were less (P = 0.087 to 0.001) for 1/4 and 3/4 Brahman than for 0 or 1/2 Brahman steers during growing, finishing, and total, but efficiency of gain did not differ (P > 0.10). Carcass weight, marbling score, quality grade (P < 0.05), and kidney fat (P = 0.06) differed among genotypes. Daily DMI (6.91 vs. 7.06 kg) was similar, but CP (0.66 vs. 0.84 kg) and ME (15.2 vs. 19.4 Mcal) intake of bromegrass fed was less (P = 0.001) than those of corn silage-fed steers. Values for DMI/gain (22.3 vs. 7.43 kg/kg), CP intake/gain (2.13 vs. 0.88 kg/kg), and ME intake/gain (48.8 vs. 20.4 Mcal/kg) were greater (P < 0.001) in bromegrass-fed than corn silage-fed steers. Over the total study, ADG was lower (0.96 vs. 1.01 kg), and DMI (7.82 vs. 7.19 kg), DMI/gain (8.21 vs. 7.10 kg/kg), and ME intake/gain (22.6 vs. 20.9 Mcal/kg) were greater (P < 0.05) in bromegrass-fed than in corn silage-fed steers. Carcass weight, dressing percent, adjusted backfat, and yield grade (P < 0.05) were greater for corn silage-fed than for bromegrass-fed steers. Feed intake and performance, but not efficiency, differed among these genotypes. Compensatory performance during finishing was insufficient to overcome reduced performance during the growing period.

Post-ruminal branched-chain amino acid supplementation and intravenous lipopolysaccharide infusion alters blood metabolites, rumen fermentation, and nitrogen balance of beef steers.

PubMed

Löest, C A; Gilliam, G G; Waggoner, J W; Turner, J L

2018-04-27

Steers exposed to an endotoxin may require additional branched-chain AA (BCAA) to support an increase in synthesis of immune proteins. This study evaluated effects of bacterial lipopolysaccharide (LPS) and BCAA supplementation on blood metabolites and N balance of 20 ruminally-cannulated steers (177 ± 4.2 kg BW). The experiment was a randomized block design, with 14-d adaptation to metabolism stalls and diet (DM fed = 1.5% BW) and 6-d collection. Treatments were a 2 × 2 factorial of LPS (0 vs 1.0 to 1.5 μg/kg BW; -LPS vs +LPS) and BCAA (0 vs 35 g/d; -BCAA vs +BCAA). The LPS in 100 mL sterile saline was infused (1 mL/min via i.v. catheter) on d 15. The BCAA in an essential AA solution were abomasally infused (900 mL/d) 3 times daily in equal portions beginning on d 7. Blood, rumen fluid, and rectal temperature were collected on d 15 at h 0, 2, 4, 8, 12, and 24 after LPS infusion. Feces and urine were collected from d 16 to 20. Rectal temperatures were greater for +LPS vs. -LPS steers at 4 h and lower at 8 h after LPS infusion (LPS h, P < 0.01). Serum cortisol and plasma urea N were greater for +LPS than -LPS steers at 2 (cortisol only), 4, 8, 12, and 24 h after LPS infusion (LPS × h, P < 0.01). Serum cortisol was greater for +BCAA than -BCAA steers at 12 h after LPS infusion (BCAA × h, P < 0.05). Serum glucose was greater for +LPS than -LPS steers at 2 h after LPS infusion (LPS × h, P < 0.01). Plasma Ile, Leu, and Val were lower, and plasma His was greater in +LPS than -LPS steers (LPS, P < 0.05). Plasma Lys, Met, Thr, and Trp of +LPS steers was lower than -LPS steers at 4 (Thr only), 8 (Lys and Trp only), 12, and 24 h after infusion (LPS × h, P < 0.05). Plasma Ile, Leu, and Val were greater (BCAA, P < 0.01), and Met, His, Phe, Thr, and Trp were lower for +BCAA than -BCAA steers at 0 h and 24 h after LPS infusion (BCAA × h, P ≤ 0.05). Steers receiving +LPS had lower rumen pH at 8 h, greater total VFA at 8 h, and lower rumen NH3 at 24 h after LPS infusion compared with -LPS steers (LPS × h, P ≤ 0.04). Total tract passage rates, DM, OM, NDF, ADF, and N intake, fecal N, digested N, and retained N were lower (P < 0.05) for +LPS than -LPS steers. Total N supply (dietary plus infused) and fecal N were greater (P < 0.05) for +BCAA vs -BCAA steers. The absence of LPS × BCAA interactions (P ≥ 0.20) for N balance indicated that post-ruminal supplementation of BCAA did not alleviate the negative effects of endotoxin on N utilization by growing steers.

Low-Absorption Liquid Crystals for Infrared Beam Steering

DTIC Science & Technology

2015-09-30

liquid crystals for infrared laser beam steering applications. To suppress the optical loss in MW1R and LW1R, we have investigated following...dielectric anisotropy, and low optical loss nematic liquid crystals for infrared laser beam steering applications. To suppress the optical loss in MWIR and...modulators. 1. Objective The main objective of this program is to develop low-loss liquid crystals for electronic laser beam steering in the infrared

A Driving Behaviour Model of Electrical Wheelchair Users

PubMed Central

Hamam, Y.; Djouani, K.; Daachi, B.; Steyn, N.

2016-01-01

In spite of the presence of powered wheelchairs, some of the users still experience steering challenges and manoeuvring difficulties that limit their capacity of navigating effectively. For such users, steering support and assistive systems may be very necessary. To appreciate the assistance, there is need that the assistive control is adaptable to the user's steering behaviour. This paper contributes to wheelchair steering improvement by modelling the steering behaviour of powered wheelchair users, for integration into the control system. More precisely, the modelling is based on the improved Directed Potential Field (DPF) method for trajectory planning. The method has facilitated the formulation of a simple behaviour model that is also linear in parameters. To obtain the steering data for parameter identification, seven individuals participated in driving the wheelchair in different virtual worlds on the augmented platform. The obtained data facilitated the estimation of user parameters, using the ordinary least square method, with satisfactory regression analysis results. PMID:27148362

Generic simulation of multi-element ladar scanner kinematics in USU LadarSIM

NASA Astrophysics Data System (ADS)

Omer, David; Call, Benjamin; Pack, Robert; Fullmer, Rees

2006-05-01

This paper presents a generic simulation model for a ladar scanner with up to three scan elements, each having a steering, stabilization and/or pattern-scanning role. Of interest is the development of algorithms that automatically generate commands to the scan elements given beam-steering objectives out of the ladar aperture, and the base motion of the sensor platform. First, a straight-forward single-element body-fixed beam-steering methodology is presented. Then a unique multi-element redirective and reflective space-fixed beam-steering methodology is explained. It is shown that standard direction cosine matrix decomposition methods fail when using two orthogonal, space-fixed rotations, thus demanding the development of a new algorithm for beam steering. Finally, a related steering control methodology is presented that uses two separate optical elements mathematically combined to determine the necessary scan element commands. Limits, restrictions, and results on this methodology are presented.

Metabolizable protein supply modulated the acute-phase response following vaccination of beef steers.

PubMed

Moriel, P; Arthington, J D

2013-12-01

Our objective was to evaluate the effects of MP supply, through RUP supplementation, on the acute-phase response of beef steers following vaccination. On d 0, Brangus-crossbred steers (n = 24; 173 ± 31 kg; 175 ± 16 d of age) were randomly assigned to receive 1 of 3 isocaloric diets formulated to provide 85, 100, and 115% of the daily MP requirements of a beef steer gaining 0.66 kg of BW daily. Diets were limit-fed at 1.8% of BW (DM basis) and individually provided to steers once daily (0800 h) from d 0 to 29. Steers were weighed on d 0 and 29, following a 12-h period of feed and water withdrawal. On d 7, steers were vaccinated against Mannheimia haemolytica (OneShot, Pfizer), and blood samples were collected on d 0, 7, 8, 10, 14, 21, and 30. Plasma metabolites were analyzed as repeated measures using the MIXED procedure of SAS. Final BW and ADG were similar (P ≥ 0.50) among treatments (mean = 184 ± 9 kg and 0.5 ± 0.08 kg/d, respectively). Effects of time were detected (P < 0.01) for plasma concentrations of all acute-phase proteins, which peaked between d 7 to 14, returning to baseline concentrations by d 29. Treatment effects were not detected (P ≥ 0.19) for plasma concentrations of acid-soluble protein, albumin, fibrinogen, IGF-1 and serum amyloid-A. Plasma concentrations of total protein (TP) and plasma urea nitrogen (PUN) increased (P ≤ 0.05) with increasing supply of MP (87.1, 89.6, and 90.1 ± 1.09 mg TP/mL and 6.1, 8.3, and 10.3 ± 0.41 mg PUN/dL for 85, 100, and 115% MP steers, respectively). From d 10 to 29, steers provided 115% MP had less (P < 0.001) plasma concentrations of ceruloplasmin than steers fed 85 and 100% MP, which had similar plasma ceruloplasmin concentrations. On d 14, plasma concentrations of haptoglobin were greatest (P ≤ 0.06) for steers fed 115% MP, intermediate for 100% MP, and least for 85% MP (0.98, 0.71 and 0.44 ± 0.099 mg/mL, respectively). On d 10, plasma concentrations of creatinine were greater (P = 0.01) for steers fed 115 vs. 85% MP, and intermediate for steers fed 100% MP (1.63, 1.28, and 1.50 ± 0.099 mg/dL, respectively). Thus, steers provided increasing metabolizable protein had greater plasma concentrations of haptoglobin, creatinine, total protein and PUN following vaccination against M. haemolytica.

Effect of beam steering on the visibility of echogenic and non-echogenic needles: a laboratory study.

PubMed

Uppal, Vishal; Sondekoppam, Rakesh V; Ganapathy, Sugantha

2014-10-01

During peripheral nerve block procedures, needle visibility decreases as the angle of needle insertion relative to skin increases due to loss of reflective signals. The primary aim of our study was to compare the effect of beam steering on the visibility of echogenic and non-echogenic block needles. PAJUNK non-echogenic and echogenic needles were inserted into pork meat at 20°, 40°, 60°, and 70° angles, and electronic beam steering was applied at three different angles (shallow, medium, and steep) to obtain the best possible needle images. Eleven anesthesiologists blinded to the type of needle or use of beam steering scored the images obtained (0 = needle not visible; 10 = excellent needle shaft and tip visibility). Mean scores were used to classify the needles as poor visibility (mean score 0-3.3), intermediate visibility (mean score 3.4-6.6), or good visibility (mean score 6.7-10). At 20°, the visibility scores were intermediate to good in all groups. At 40°, the mean (SD) visibility score for the non-echogenic needle improved significantly from 3.1 (1.4) to 7.9 (1.8) with application of beam steering (difference = 4.8; 95% confidence interval [CI]: 3.1 to 6.6; P < 0.001). At 60°, the mean (SD) visibility score for the non-echogenic needle was poor 0.6 (0.7) and remained poor 2.4 (1.1) with beam steering. One the other hand, the echogenic needle without beam steering 6.5 (1.8) scored significantly better than the non-echogenic needle with beam steering 2.4 (1.1) (difference = 4.2; 95% CI: 2.7 to 5.6; P < 0.001). At 70°, the mean needle visibility score was poor for the non-echogenic needle with or without beam steering. In contrast, the echogenic needle attained an intermediate visibility score with or without beam steering. Beam steering did not significantly change the visibility scores of either the echogenic or the non-echogenic needle (P = 0.088 and 0.056, respectively) at a 70° angle. The PAJUNK echogenic needle, with or without beam steering, was more visible when compared with the non-echogenic needle at 60° and 70° angles of insertion. In contrast, at a 40° angle of needle insertion, the non-echogenic needle with beam steering was more visible compared with the echogenic needle.

Comparison of dairy beef genetics and dietary roughage levels.

PubMed

Lehmkuhler, J W; Ramos, M H

2008-06-01

The objectives of these trials were to investigate the performance of Jersey steers in relation to Holsteins under current management practices when fed diets differing in energy density and subsequent effects on carcass characteristics. In experiment 1, twelve Jersey and 12 Holstein steers were offered dietary treatments with differing roughage levels. Roughage levels investigated on a dry matter basis were 55% reduced to 25% versus 25% followed by 12.5% (HIGH and LOW, respectively) with all animals receiving the same finishing diet containing 6.5% roughage. Holstein steers were heavier than Jerseys at the initiation of the trial (228 vs. 116 kg). A diet response was observed for gain efficiency during the first period in which LOW was greater than HIGH. Holstein steers had higher dry matter intakes and rates of gain than Jerseys. However, gain efficiency was better for Jersey steers during the first and last periods. Carcass traits were influenced by breed but not diet. Holsteins had heavier hot carcass weights, greater dressing percentages, more backfat, and larger longissimus muscle area, whereas marbling scores were similar to Jerseys. The increased efficiency of Jersey steers and significant reduction in carcass value due to light carcass weights suggested that Jersey steers should be fed to heavier live weights. Experiment 2 utilized 85 steers to investigate continuous feeding of a low-roughage, high-concentrate diet versus a phase-feeding strategy. Jersey (n = 40) and Holstein (n = 45) steers were assigned to a diet containing 20% corn silage on a dry matter basis (HEN) or a phase-feeding program (PHASE) in which corn silage was reduced from 60 to 40% followed by the same diet as HEN. Initial body weights were similar for dietary treatments but differed by breed. A diet response was observed for live weight at the end of the first and second period, first period average daily gain (ADG), overall ADG, and days on feed with HEN having higher ADG than PHASE and fewer days on feed. Breed affected all body weight and gain variables with Holsteins being heavier and gaining more rapidly than Jersey steers. Jersey carcasses were lighter, had the highest percentage trim loss, least amount of backfat, and lowest numerical yield grade. Holstein steers had a greater propensity for gain, whereas the Jersey steers were equally or more efficient. These findings suggest that phase feeding Jersey steers higher-roughage diets has minimal effect on carcass traits.

Feed efficiency differences and reranking in beef steers fed grower and finisher diets.

PubMed

Durunna, O N; Mujibi, F D N; Goonewardene, L; Okine, E K; Basarab, J A; Wang, Z; Moore, S S

2011-01-01

This 3-yr study used 490 steers to determine whether feedlot steers changed their feed efficiency (FE) ranking when fed a grower diet, then a finisher diet. The steers were crossbreds and were between 5 to 7 mo of age. There were 2 feeding periods each year. Within each year, approximately 90 steers had their diet switched from a grower to a finisher diet (feed-swap group), whereas another 90 steers were fed either the grower (grower-fed group) or the finisher (finisher-fed group) diet throughout the feeding trial. Each feeding test lasted for a minimum of 10 wk, and all steers were fed ad libitum. Individual animal feed intakes were collected using the GrowSafe feeding system, and BW were measured every 2 wk. Residual feed intake (RFI), G:F, and Kleiber ratio (KR) were computed at the end of each feeding period. For each measure of efficiency, animals were classified as low, medium, or high based on 0.5 SD from the mean. The majority of steers did not maintain the previous efficiency class in the second period. Approximately 58, 51, and 51% of steers in the feed-swap group, finisher-fed group, and the grower-fed group, respectively, changed their RFI measure by 0.5 SD. A low rank correlation occurred in all test groups but was less in the feed-swap group. Spearman rank correlations between the 2 feeding periods in the feed-swap group were 0.33, 0.20, and 0.31 for RFI, G:F, and KR, respectively. Classifications based on G:F and KR showed that a greater number of steers (P < 0.05) in the feed-swap group did not maintain their FE class from 1 feeding regimen to the other, whereas classification based on RFI did not show any difference (P > 0.05) between the proportions of individuals that changed or maintained their FE class. In the groups without a feed-swap, there was no difference (P > 0.05) in the proportion of steers that changed or maintained the same FE class for all FE measures. Our results suggest that diet type and feeding period affect the FE ranking in beef steers. A feedlot diet is ideal for evaluating the FE potential of steers for feedlot profitability; however, we suggest that tests involving less dense diets should be examined in an effort to understand the relationships between FE and feeder profitability.

Path optimisation of a mobile robot using an artificial neural network controller

NASA Astrophysics Data System (ADS)

Singh, M. K.; Parhi, D. R.

2011-01-01

This article proposed a novel approach for design of an intelligent controller for an autonomous mobile robot using a multilayer feed forward neural network, which enables the robot to navigate in a real world dynamic environment. The inputs to the proposed neural controller consist of left, right and front obstacle distance with respect to its position and target angle. The output of the neural network is steering angle. A four layer neural network has been designed to solve the path and time optimisation problem of mobile robots, which deals with the cognitive tasks such as learning, adaptation, generalisation and optimisation. A back propagation algorithm is used to train the network. This article also analyses the kinematic design of mobile robots for dynamic movements. The simulation results are compared with experimental results, which are satisfactory and show very good agreement. The training of the neural nets and the control performance analysis has been done in a real experimental setup.

Method for controlling a vehicle with two or more independently steered wheels

DOEpatents

Reister, David B.; Unseren, Michael A.

1995-01-01

A method (10) for independently controlling each steerable drive wheel (W.sub.i) of a vehicle with two or more such wheels (W.sub.i). An instantaneous center of rotation target (ICR) and a tangential velocity target (v.sup.G) are inputs to a wheel target system (30) which sends the velocity target (v.sub.i.sup.G) and a steering angle target (.theta..sub.i.sup.G) for each drive wheel (W.sub.i) to a pseudovelocity target system (32). The pseudovelocity target system (32) determines a pseudovelocity target (v.sub.P.sup.G) which is compared to a current pseudovelocity (v.sub.P.sup.m) to determine a pseudovelocity error (.epsilon.). The steering angle targets (.theta..sup.G) and the steering angles (.theta..sup.m) are inputs to a steering angle control system (34) which outputs to the steering angle encoders (36), which measure the steering angles (.theta..sup.m). The pseudovelocity error (.epsilon.), the rate of change of the pseudovelocity error ( ), and the wheel slip between each pair of drive wheels (W.sub.i) are used to calculate intermediate control variables which, along with the steering angle targets (.theta..sup.G) are used to calculate the torque to be applied at each wheel (W.sub.i). The current distance traveled for each wheel (W.sub.i) is then calculated. The current wheel velocities (v.sup.m) and steering angle targets (.theta..sup.G) are used to calculate the cumulative and instantaneous wheel slip (e, ) and the current pseudovelocity (v.sub.P.sup.m).

Identifying cognitive distraction using steering wheel reversal rates.

PubMed

Kountouriotis, Georgios K; Spyridakos, Panagiotis; Carsten, Oliver M J; Merat, Natasha

2016-11-01

The influence of driver distraction on driving performance is not yet well understood, but it can have detrimental effects on road safety. In this study, we examined the effects of visual and non-visual distractions during driving, using a high-fidelity driving simulator. The visual task was presented either at an offset angle on an in-vehicle screen, or on the back of a moving lead vehicle. Similar to results from previous studies in this area, non-visual (cognitive) distraction resulted in improved lane keeping performance and increased gaze concentration towards the centre of the road, compared to baseline driving, and further examination of the steering control metrics indicated an increase in steering wheel reversal rates, steering wheel acceleration, and steering entropy. We show, for the first time, that when the visual task is presented centrally, drivers' lane deviation reduces (similar to non-visual distraction), whilst measures of steering control, overall, indicated more steering activity, compared to baseline. When using a visual task that required the diversion of gaze to an in-vehicle display, but without a manual element, lane keeping performance was similar to baseline driving. Steering wheel reversal rates were found to adequately tease apart the effects of non-visual distraction (increase of 0.5° reversals) and visual distraction with offset gaze direction (increase of 2.5° reversals). These findings are discussed in terms of steering control during different types of in-vehicle distraction, and the possible role of manual interference by distracting secondary tasks. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cattle temperament influences metabolism: metabolic response to glucose tolerance and insulin sensitivity tests in beef steers.

PubMed

Burdick Sanchez, N C; Carroll, J A; Broadway, P R; Hughes, H D; Roberts, S L; Richeson, J T; Schmidt, T B; Vann, R C

2016-07-01

Cattle temperament, defined as the reactivity of cattle to humans or novel environments, can greatly influence several physiological systems in the body, including immunity, stress, and most recently discovered, metabolism. Greater circulating concentrations of nonesterified fatty acids (NEFAs) found in temperamental cattle suggest that temperamental cattle are metabolically different than calm cattle. Further, elevated NEFA concentrations have been reported to influence insulin sensitivity. Therefore, the objective of this study was to determine whether cattle temperament would influence the metabolic response to a glucose tolerance test (GTT) and insulin sensitivity test (IST). Angus-cross steers (16 calm and 15 temperamental; 216 ± 6 kg BW) were selected based on temperament score measured at weaning. On day 1, steers were moved into indoor stanchions to allow measurement of individual ad libitum feed intake. On day 6, steers were fitted with indwelling rectal temperature probes and jugular catheters. At 9 AM on day 7, steers received the GTT (0.5-mL/kg BW of a 50% dextrose solution), and at 2 PM on day 7, steers received the IST (2.5 IU bovine insulin/kg BW). Blood samples were collected and serum isolated at -60, -45, -30, -15, 0, 10, 20, 30, 45, 60, 90, 120, and 150 min relative to each challenge. Serum was stored at -80°C until analyzed for cortisol, glucose, NEFA, and blood urea nitrogen concentrations. All variables changed over time (P < 0.01). For the duration of the study, temperamental steers maintained greater (P < 0.01) serum NEFA and less (P ≤ 0.01) serum blood urea nitrogen and insulin sensitivity (calculated using Revised Quantitative Insulin Sensitivity Check Index) compared with calm steers. During the GTT, temperamental steers had greater (P < 0.01) serum glucose, yet decreased (P = 0.03) serum insulin and (P < 0.01) serum insulin: serum glucose compared to calm cattle. During the IST, temperamental steers had greater (P < 0.01) serum insulin and a greater (P < 0.01) serum insulin: serum glucose as compared with calm steers. These data demonstrate that differences exist in the manner in which temperamental steers respond to glucose and insulin, potentially a result of elevated serum NEFA concentrations, which may result in changes in utilization and redistribution of energy in temperamental vs calm cattle. Published by Elsevier Inc.

Noncommutative Line Bundles and Gerbes

NASA Astrophysics Data System (ADS)

Jurčo, B.

We introduce noncommutative line bundles and gerbes within the framework of deformation quantization. The Seiberg-Witten map is used to construct the corresponding noncommutative Čech cocycles. Morita equivalence of star products and quantization of twisted Poisson structures are discussed from this point of view.

Violation of continuous-variable Einstein-Podolsky-Rosen steering with discrete measurements.

PubMed

Schneeloch, James; Dixon, P Ben; Howland, Gregory A; Broadbent, Curtis J; Howell, John C

2013-03-29

In this Letter, we derive an entropic Einstein-Podolsky-Rosen (EPR) steering inequality for continuous-variable systems using only experimentally measured discrete probability distributions and details of the measurement apparatus. We use this inequality to witness EPR steering between the positions and momenta of photon pairs generated in spontaneous parametric down-conversion. We examine the asymmetry between parties in this inequality, and show that this asymmetry can be used to reduce the technical requirements of experimental setups intended to demonstrate the EPR paradox. Furthermore, we develop a more stringent steering inequality that is symmetric between parties, and use it to show that the down-converted photon pairs also exhibit symmetric EPR steering.

Violation of Continuous-Variable Einstein-Podolsky-Rosen Steering with Discrete Measurements

NASA Astrophysics Data System (ADS)

Schneeloch, James; Dixon, P. Ben; Howland, Gregory A.; Broadbent, Curtis J.; Howell, John C.

2013-03-01

In this Letter, we derive an entropic Einstein-Podolsky-Rosen (EPR) steering inequality for continuous-variable systems using only experimentally measured discrete probability distributions and details of the measurement apparatus. We use this inequality to witness EPR steering between the positions and momenta of photon pairs generated in spontaneous parametric down-conversion. We examine the asymmetry between parties in this inequality, and show that this asymmetry can be used to reduce the technical requirements of experimental setups intended to demonstrate the EPR paradox. Furthermore, we develop a more stringent steering inequality that is symmetric between parties, and use it to show that the down-converted photon pairs also exhibit symmetric EPR steering.

Micromachined actuators/sensors for intratubular positioning/steering

DOEpatents

Lee, A.P.; Krulevitch, P.A.; Northrup, M.A.; Trevino, J.C.

1998-06-30

Micromachined thin film cantilever actuators having means for individually controlling the deflection of the cantilevers, valve members, and rudders for steering same through blood vessels, or positioning same within a blood vessel, for example. Such cantilever actuators include tactile sensor arrays mounted on a catheter or guide wire tip for navigation and tissues identification, shape-memory alloy film based catheter/guide wire steering mechanisms, and rudder-based steering devices that allow the selective actuation of rudders that use the flowing blood itself to help direct the catheter direction through the blood vessel. While particularly adapted for medical applications, these cantilever actuators can be used for steering through piping and tubing systems. 14 figs.

Chaos in quantum steering in high-dimensional systems

NASA Astrophysics Data System (ADS)

He, Guang Ping

2018-04-01

Quantum steering means that in some bipartite quantum systems the local measurements on one side can determine the state of the other side. Here we show that in high-dimensional systems there exists a specific entangled state which can display a kind of chaos effect when being adopted for steering. That is, a subtle difference in the measurement results on one side can steer the other side into completely orthogonal states. Moreover, by expanding the result to infinite-dimensional systems, we find two sets of states for which, contrary to common belief, even though their density matrices approach being identical, the steering between them is impossible. This property makes them very useful for quantum cryptography.

Focused Ultrasound Steering for Harmonic Motion Imaging.

PubMed

Han, Yang; Payen, Thomas; Wang, Shutao; Konofagou, Elisa

2018-02-01

Harmonic motion imaging (HMI) is a radiation-force-based ultrasound elasticity imaging technique, which is designed for both tissue relative stiffness imaging and reliable high-intensity focused ultrasound treatment monitoring. The objective of this letter is to develop and demonstrate the feasibility of 2-D focused ultrasound (FUS) beam steering for HMI using a 93-element, FUS phased array. HMI with steered FUS beam was acquired in tissue-mimicking phantoms. The HMI displacement was imaged within the steering range of ±1.7 mm laterally and ±2 mm axially. Using the steered FUS beam, HMI can be used to image a larger tissue volume with higher efficiency and without requiring mechanical movement of the transducer.

Common Ada (tradename) Missile Package (CAMP) Project. Missile Software Parts. Volume 8. Detail Design Document

DTIC Science & Technology

1988-03-01

PACKAGE BODY ) TLCSC P661 (CATALOG #P106-0) This package contains the CAMP parts required to do the vaypoint steering portion of navigation. The...3.3.4.1.6 PROCESSING The following describes the processing performed by this part: package body WaypointSteering is package body ...Steering_Vector_Operations is separate; package body Steering_Vector_Operations_with_Arcsin is separate; procedure Compute Turn_Angle_and Direction (UnitNormal C

Twenty-four hour Holter monitoring in finishing cattle housed outdoors.

PubMed

Frese, D A; Thomason, J D; Reinhardt, C; Bartle, S; Rethorst, D; Loneragan, G H; Thomson, D

2017-04-01

Atrial premature complexes have been reported to be the most common arrhythmia in cattle and is suspected to be secondary to systemic disease, especially gastrointestinal disease. In order to properly identify pathologic arrhythmia in cattle, the normal rhythm and arrhythmia prevalence should be defined. The objective of this study was to determine the normal heart rate, rhythm, number of ventricular premature complexes (VPCs), and atrial premature complexes (APCs) in unrestrained Angus steers. Twenty-seven client owned steers with unremarkable physical examinations and serum biochemical analyses were used. Twenty-four hour Holter monitors, attached by a custom-made harness, were retrospectively evaluated. Three lead electrocardiographic registrations of good quality and normal sinus rhythm were obtained from all steers in the study. The mean heart rate was 66.8 bpm ± 16.4 bpm. Ventricular premature complexes were rare (noted in 14.8% of steers), and APCs were common (noted in 85% of the steers). Simple second degree AV block was observed in 18.5% of the steers. In summary, healthy steers have rare single VPCs, although it is possible for an individual animal to have apparent more frequent VPCs. Mean heart rate varies with a diurnal pattern similar to other species. Atrial premature complexes are the most prevalent abnormality observed in feedlot steers. Copyright © 2016 Elsevier B.V. All rights reserved.

Bell’s Nonlocality Can be Detected by the Violation of Einstein-Podolsky-Rosen Steering Inequality

PubMed Central

Chen, Jing-Ling; Ren, Changliang; Chen, Changbo; Ye, Xiang-Jun; Pati, Arun Kumar

2016-01-01

Recently quantum nonlocality has been classified into three distinct types: quantum entanglement, Einstein-Podolsky-Rosen steering, and Bell’s nonlocality. Among which, Bell’s nonlocality is the strongest type. Bell’s nonlocality for quantum states is usually detected by violation of some Bell’s inequalities, such as Clause-Horne-Shimony-Holt inequality for two qubits. Steering is a manifestation of nonlocality intermediate between entanglement and Bell’s nonlocality. This peculiar feature has led to a curious quantum phenomenon, the one-way Einstein-Podolsky-Rosen steering. The one-way steering was an important open question presented in 2007, and positively answered in 2014 by Bowles et al., who presented a simple class of one-way steerable states in a two-qubit system with at least thirteen projective measurements. The inspiring result for the first time theoretically confirms quantum nonlocality can be fundamentally asymmetric. Here, we propose another curious quantum phenomenon: Bell nonlocal states can be constructed from some steerable states. This novel finding not only offers a distinctive way to study Bell’s nonlocality without Bell’s inequality but with steering inequality, but also may avoid locality loophole in Bell’s tests and make Bell’s nonlocality easier for demonstration. Furthermore, a nine-setting steering inequality has also been presented for developing more efficient one-way steering and detecting some Bell nonlocal states. PMID:27966616

Artificial intelligence for the EChO mission planning tool

NASA Astrophysics Data System (ADS)

Garcia-Piquer, Alvaro; Ribas, Ignasi; Colomé, Josep

2015-12-01

The Exoplanet Characterisation Observatory (EChO) has as its main goal the measurement of atmospheres of transiting planets. This requires the observation of two types of events: primary and secondary eclipses. In order to yield measurements of sufficient Signal-to-Noise Ratio to fulfil the mission objectives, the events of each exoplanet have to be observed several times. In addition, several criteria have to be considered to carry out each observation, such as the exoplanet visibility, its event duration, and no overlapping with other tasks. It is expected that a suitable mission plan increases the efficiency of telescope operation, which will represent an important benefit in terms of scientific return and operational costs. Nevertheless, to obtain a long term mission plan becomes unaffordable for human planners due to the complexity of computing the huge number of possible combinations for finding an optimum solution. In this contribution we present a long term mission planning tool based on Genetic Algorithms, which are focused on solving optimization problems such as the planning of several tasks. Specifically, the proposed tool finds a solution that highly optimizes the defined objectives, which are based on the maximization of the time spent on scientific observations and the scientific return (e.g., the coverage of the mission survey). The results obtained on the large experimental set up support that the proposed scheduler technology is robust and can function in a variety of scenarios, offering a competitive performance which does not depend on the collection of exoplanets to be observed. Specifically, the results show that, with the proposed tool, EChO uses 94% of the available time of the mission, so the amount of downtime is small, and it completes 98% of the targets.

Pesticide residue evaluation in major staple food items of Ethiopia using the QuEChERS method: a case study from the Jimma Zone.

PubMed

Mekonen, Seblework; Ambelu, Argaw; Spanoghe, Pieter

2014-06-01

Samples of maize, teff, red pepper, and coffee (green bean and coffee bean with pulp) were collected from a local market in the Jimma Zone, Ethiopia. Samples were analyzed for the occurrence of cypermethrin, permethrin, deltamethrin, chlorpyrifos ethyl, DTT and its metabolites, and endosulfan (α, β). In the analytical procedure, the QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) extraction methodology with dispersive solid phase extraction clean up (d-SPE) technique was applied. Validation of the QuEChERS method was satisfactory. Recovery percentages of most pesticides were in the range of 70% to 120%, with good repeatability (%relative standard deviation < 20). The limit of detection and limit of quantification varied between 0.001 µg/g and 0.092 µg/g and between 0.002 µg/g and 0.307 µg/g, respectively. The main pesticides detected were DDT, endosulfan, cypermethrin, and permethrin. All of the pesticides analyzed were detected in red pepper and green coffee bean. Residues of DDT in coffee pulp significantly differed (p < 0.01) from other food items except for red pepper. The concentration of pesticides in the food items varied from 0.011 mg/kg to 1.115 mg/kg. All food items contained 1 or more pesticides. Two-thirds of the samples had residues below corresponding maximum residue limits, and the remaining one-third of samples were above the maximum residue limits. These results indicate the need for a good pesticide monitoring program to evaluate consumer risk for the Ethiopian people. © 2014 SETAC.

Residue analysis of four diacylhydrazine insecticides in fruits and vegetables by Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) method using ultra-performance liquid chromatography coupled to tandem mass spectrometry.

PubMed

Liu, Xingang; Xu, Jun; Dong, Fengshou; Li, Yuanbo; Song, Wenchen; Zheng, Yongquan

2011-08-01

The new analytical method using Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) procedure for simultaneous determination of diacylhydrazine insecticide residues in fruits and vegetables was developed using ultra-performance liquid chromatography coupled with tandem mass spectrometry (UPLC-MS/MS). The four insecticides (tebufenozide, methoxfenozide, chromafenozide, and halofenozide) were extracted from six fruit and vegetable matrices using acetonitrile and subsequently cleaned up using primary secondary amine (PSA) or octadecylsilane (C18) as sorbent prior to UPLC-MS/MS analysis. The determination of the target compounds was achieved in less than 3.0 min using an electrospray ionization source in positive mode (ESI+) for tebufenozide, methoxfenozide, and halofenozide and in negative mode (ESI-) for chromafenozide. The limits of detection were below 0.6 μg kg(-1), while the limit of quantification did not exceed 2 μg kg(-1) in different matrices. The QuEChERS procedure by using two sorbents (PSA and C18) and the matrix-matched standards gave satisfactory recoveries and relative standard deviation (RSD) values in different matrices at four spiked levels (0.01, 0.05, 0.1, and 1 mg kg(-1)). The overall average recoveries for this method in apple, grape, cucumber, tomato, cabbage, and spinach at four levels ranged from 74.2% to 112.5% with RSDs in the range of 1.4-13.8% (n = 5) for all analytes. This study provides a theoretical basis for China to draw up maximum residue limits and analytical method for diacylhydrazine insecticide in vegetables and fruits.

Simultaneous determination of five plant growth regulators in fruits by modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) extraction and liquid chromatography-tandem mass spectrometry.

PubMed

Shi, Xiaomei; Jin, Fen; Huang, Yuting; Du, Xinwei; Li, Chunmei; Wang, Miao; Shao, Hua; Jin, Maojun; Wang, Jing

2012-01-11

An effective method using liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed and optimized to obtain a complete separation of five representative plant growth regulators (PGRs) [gibberellic acid, 2,4-dichlorophenoxyacetic acid (2,4-D), thidiazuron, forchlorfenuron, and paclobutrazol] in fruits. Extraction was performed with acetonitrile containing 0.1% (v/v) acetic acid, applying modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) methodology. LC-MS/MS conditions including composition of mobile phases and mass spectrometry (MS) conditions were evaluated to achieve the highest sensitivity in MS detection. All of the data acquisition was employed in the segmented multiple-reaction monitoring mode for the selected negative and positive transition ions. The octadecylsilyl (C18) dispersive solid-phase extraction (SPE) sorbent was found to provide the more satisfied recoveries than primary secondary amine (PSA) and graphitized carbon black (GCB) for five target PGRs. The optimized method allowed for recoveries of 76-112% for the five PGRs from fruit samples with relative standard deviation (RSD) values less than 10%. Limits of quantification (0.5-16.5 μg/kg) were lower than the maximum limit of residues established for PGRs. The results demonstrated that the developed LC-MS/MS and QuEChERS extraction method is highly effective for analyzing trace amounts of target PGRs in fruit samples. Finally, the method was successfully used to detect residual PGRs in Beijing, China, in 2010. The concentrations of 2,4-D (5.1-1503 μg/kg) and paclobutrazol (1-1381 μg/kg) found in orange and peach, respectively, suggesting that the use of these PGRs in these fruits should be regulated in China in the future.

Elimination of hydrogenase active site assembly blocks H2 production and increases ethanol yield in Clostridium thermocellum

DOE PAGES

Biswas, Ranjita; Zheng, Tianyong; Olson, Daniel G.; ...

2015-02-12

The native ability of Clostridium thermocellum to rapidly consume cellulose and produce ethanol makes it a leading candidate for a consolidated bioprocessing (CBP) biofuel production strategy. C. thermocellum also synthesizes lactate, formate, acetate, H2, and amino acids that compete with ethanol production for carbon and electrons. Elimination of H2 production could redirect carbon flux towards ethanol production by making more electrons available for acetyl-CoA reduction to ethanol. C. thermocellum encodes four hydrogenases and rather than delete each individually, we targeted a hydrogenase maturase gene (hydG), involved in converting the three [FeFe] hydrogenase apoenzymes into holoenzymes. Further deletion of the [NiFe]more » hydrogenase (ech) resulted in a mutant that functionally lacks all four hydrogenases. H2 production in hydG ech was undetectable and ethanol yield increased nearly 2-fold compared to wild type. Interestingly, mutant growth improved upon the addition of acetate, which led to increased expression of genes related to sulfate metabolism, suggesting these mutants may use sulfate as a terminal electron acceptor to balance redox reactions. Genomic analysis of hydG revealed a mutation in adhE, resulting in a strain with both NADH- and NADPH-dependent alcohol dehydrogenase activities. While this same adhE mutation is found in ethanol tolerant C. thermocellum strain E50C, hydG and hydG ech are not more ethanol tolerant than wild type, illustrating the complicated interactions between redox balancing and ethanol tolerance in C. thermocellum. The dramatic increase in ethanol production here suggests that targeting protein post-translational modification is a promising new approach for inactivation of multiple enzymes simultaneously for metabolic engineering.« less

Risk of thoracic injury from direct steering wheel impact in frontal crashes.

PubMed

Chen, Rong; Gabler, Hampton C

2014-06-01

The combination of airbag and seat belt is considered to be the most effective vehicle safety system. However, despite the widespread availability of airbags and a belt use rate of more than 85%, US drivers involved in crashes continue to be at risk of serious thoracic injury. The objective of this study was to determine the influence of steering wheel deformation on driver injury risk in frontal automobile crash. The analysis is based on cases extracted from the National Automotive Sampling System Crashworthiness Data System database for case years 1993 to 2011. The approach was to compare the adjusted odds of frontal crash injury experienced by drivers in vehicles with and without steering wheel deformation. Among frontal crash cases with belted drivers, observable steering wheel deformation occurred in less than 4% of all cases but accounted for 30% of belted drivers with serious (Abbreviated Injury Scale [AIS] score, 3+) thoracic injuries. Similarly, steering wheel deformation occurred in approximately 13% of unbelted drivers but accounted for 60% of unbelted drivers with serious thoracic injuries. Belted drivers in frontal crashes with steering wheel deformation were found to have two times greater odds of serious thoracic injury. Unbelted drivers were found to have four times greater odds of serious thoracic injury in crashes with steering wheel deformation. In frontal crashes, steering wheel deformation was more likely to occur in unbelted drivers than belted drivers, as well as higher severity crashes and with heavier drivers. The results of the present study show that airbag deployment and seat belt restraint do not completely eliminate the possibility of steering wheel contact. Even with the most advanced restraint systems, there remains an opportunity for further reduction in thoracic injury by continued enhancement to the seat belt and airbag systems. Furthermore, the results showed that steering wheel deformation is an indicator of potential serious thoracic injury and can be useful to prehospital personnel in improving the diagnosis of serious injuries. Prognostic study, level III.

Development of the auto-steering software and equipment technology (ASSET)

NASA Astrophysics Data System (ADS)

McKay, Mark D.; Anderson, Matthew O.; Wadsworth, Derek C.

2003-09-01

The Idaho National Engineering and Environmental Laboratory (INEEL), through collaboration with INSAT Co., has developed a low cost robotic auto-steering system for parallel contour swathing. The capability to perform parallel contour swathing while minimizing "skip" and "overlap" is a necessity for cost-effective crop management within precision agriculture. Current methods for performing parallel contour swathing consist of using a Differential Global Position System (DGPS) coupled with a light bar system to prompt an operator where to steer. The complexity of operating heavy equipment, ensuring proper chemical mixture and application, and steering to a light bar indicator can be overwhelming to an operator. To simplify these tasks, an inexpensive robotic steering system has been developed and tested on several farming implements. This development leveraged research conducted by the INEEL and Utah State University. The INEEL-INSAT Auto-Steering Software and Equipment Technology provides the following: 1) the ability to drive in a straight line within +/- 2 feet while traveling at least 15 mph, 2) interfaces to a Real Time Kinematic (RTK) DGPS and sub-meter DGPS, 3) safety features such as Emergency-stop, steering wheel deactivation, computer watchdog deactivation, etc., and 4) a low-cost, field-ready system that is easily adapted to other systems.

Modern Control Aspects of Automatically Steered Vehicles

DOT National Transportation Integrated Search

1971-12-01

In the study of automatically steered rubber tired vehicles, little emphasis in the past has been placed on the steering control laws. The report examines the control law problem from the state variable point of view and it is shown that, except for ...

Feasibility of Onboard Processing of Heuristic Path Planning and Navigation Algorithms within SUAS Autopilot Computational Constraints

DTIC Science & Technology

2014-03-01

brake_group > NONE </ brake_group > <retractable>0</retractable> </contact> <contact type="BOGEY" name="RIGHT_MLG...damping_coeff> <max_steer unit="DEG"> 0.0 </max_steer> < brake_group > NONE </ brake_group > <retractable>0</retractable...damping_coeff unit="LBS/FT/SEC"> 100 </damping_coeff> <max_steer unit="DEG"> 360.0 </max_steer> < brake_group > NONE

Vehicle Steering control: A model of learning

NASA Technical Reports Server (NTRS)

Smiley, A.; Reid, L.; Fraser, M.

1978-01-01

A hierarchy of strategies were postulated to describe the process of learning steering control. Vehicle motion and steering control data were recorded for twelve novices who drove an instrumented car twice a week during and after a driver training course. Car-driver describing functions were calculated, the probable control structure determined, and the driver-alone transfer function modelled. The data suggested that the largest changes in steering control with learning were in the way the driver used the lateral position cue.

Packaging consideration of two-dimensional polymer-based photonic crystals for laser beam steering

NASA Astrophysics Data System (ADS)

Dou, Xinyuan; Chen, Xiaonan; Chen, Maggie Yihong; Wang, Alan Xiaolong; Jiang, Wei; Chen, Ray T.

2009-02-01

In this paper, we report the theoretical study of polymer-based photonic crystals for laser beam steering which is based on the superprism effect as well as the experiment fabrication of the two dimensional photonic crystals for the laser beam steering. Superprism effect, the principle for beam steering, was separately studied in details through EFC (Equifrequency Contour) analysis. Polymer based photonic crystals were fabricated through double exposure holographic interference method using SU8-2007. The experiment results were also reported.

Estimation of Skidding Offered by Ackermann Mechanism

NASA Astrophysics Data System (ADS)

Rao, Are Padma; Venkatachalam, Rapur

2016-04-01

Steering for a four wheeler is being provided by Ackermann mechanism. Though it cannot always provide correct steering conditions, it is very popular because of its simple nature. A correct steering would avoid skidding of the tires, and thereby enhance their lives as the wear of the tires is reduced. In this paper it is intended to analyze Ackermann mechanism for its performance. A method of estimating skidding due to improper steering is proposed. Two parameters are identified using which the length of skidding can be estimated.

49 CFR 571.208a - Optional test procedures for vehicles manufactured between January 27, 2004 and August 31, 2004.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 20.6 °C and 22.2 °C (69 °F to 72 °F). S16.2.9 Steering wheel adjustment. S16.2.9.1 Adjust a tiltable steering wheel, if possible, so that the steering wheel hub is at the geometric center of its full range of driving positions. S16.2.9.2 If there is no setting detent at the mid-position, lower the steering wheel...

Endocrine Gland and Brain Weights of Market Weight Bulls and Steers Representing the Shorthorn Breed and Several Breed Crosses

PubMed Central

Doornenbal, H.

1974-01-01

Thyroid, adrenal, pituitary and brain weights were first determined in 1971 in 492 market weight cattle representing purebred Shorthorns and crosses of “foreign” breeds, Charolais, Simmental and Limousin with Hereford, Angus and Shorthorn. Thyroid weights were also determined in a similar group of 433 cattle the following year. The data were reported on a per 100 kg body weight basis and analyzed within the subgroups of breed of sire, breed of dam and location. The average thyroid weight per 100 kg of body weight for males within subgroups over the two years ranged from 3.99 to 8.71 g, while that for steers ranged from 3.81 to 4.41 g. The average thyroid weight for a group of 18 Limousin sired heifers was 3.71 g. The average adrenal weight per 100 kg of slaughter weight ranged from 3.66 to 4.20 g in the males and from 3.66 to 3.86 g in the steers. Pituitary weight per 100 kg body weight at slaughter ranged from 486-511 mg in bulls and from 469-510 mg in steers. Average brain weight ranged from 85.5 to 97.3 g in males and from 92.2 to 94.1 g in steers. Breed differences existed only for the pituitary gland, with Simmental sired males and steers having heavier glands than Charolais sired males and steers. Sex differences were significant for the thyroid and the brain. Thyroids of males were generally heavier than those of steers, while brains of steers were heavier than those from males. Thyroid, adrenal and brain weights were significantly different between two genetically similar purebred herds of Shorthorns. PMID:4279761

Block by Block: Civic Action in the Battle of Baghdad

DTIC Science & Technology

2007-11-01

powdered musk and ambergris. Arts and sciences flourished— literature, music, calligraphy, philosophy, mathematics, chemistry, history. All that was...of the insur- gency, (i.e., guerrilla, underground, and auxiliary). The basic premise of civic-action operations is that the lower ech- elon of

A modified QuEChERS method for the determination of some herbicides in yogurt and milk by high performance liquid chromatography.

PubMed

Li, Na; Lei, Lei; Nian, Li; Zhang, Rui; Wu, Shuting; Ren, Ruibing; Wang, Yeqiang; Zhang, Hanqi; Yu, Aimin

2013-02-15

A modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) method was applied to the extraction of triazines and phenylureas from milk and yogurt. The herbicides was extracted by the mixture of ethyl acetate and n-hexane and cleaned by primary secondary amine (10mg/mL). The frozen-out centrifugation was applied to further remove fatty. The proposed method can achieve efficient extraction and cleanup. Some experimental parameters, such as extraction method, extraction solvent and adsorbent, pH of sample solution, extraction time and amount of primary secondary amine and sodium chloride were investigated and optimized. The precision and absolute recoveries of eight herbicides vary from 0.07 to 5.86% and from 78.9 to 99.9%, respectively. The detection limits for simeton, monuron, chlorotoluron, simetryne, atrazine, karmex, ametryne and propazine range from 0.15 to 0.35 ng/mL. Copyright © 2012 Elsevier B.V. All rights reserved.

Multiresidue method for the determination of pesticides in Oolong tea using QuEChERS by gas chromatography-triple quadrupole tandem mass spectrometry.

PubMed

Wu, Chia-Chang

2017-08-15

We propose a simple, rapid analytical method for determination of 89 pesticides in Oolong tea by GC/MS/MS. Samples were extracted via QuEChERS. The limits of detection and quantification range of the 89 pesticides were 1-25μgL -1 and 10-50μgL -1 , respectively. Good separation was attained in less than 36min. A wide linear range of 1-250μgL -1 was observed with r 2 values from 0.9955 to 0.9998. Pesticide-free tea powder spiked at 50 and 100μgL -1 . Recovery ranges of the 86 (50μgL -1 ) and 83 (100μgL -1 ) pesticides were from 60% to 120%. Relative standard deviations were less than 20%. The laboratory proficiency test (FAPAS, 2014) shows satisfactory (|z|<2) z-score values. The proposed monitoring technique rapidly and efficiently screens, multiple pesticides in Oolong tea. Copyright © 2017 Elsevier Ltd. All rights reserved.

High frequency plasma generator for ion thrusters

NASA Technical Reports Server (NTRS)

Goede, H.; Divergilio, W. F.; Fosnight, V. V.; Komatsu, G.

1984-01-01

The results of a program to experimentally develop two new types of plasma generators for 30 cm electrostatic argon ion thrusters are presented. The two plasma generating methods selected for this study were by radio frequency induction (RFI), operating at an input power frequency of 1 MHz, and by electron cyclotron heating (ECH) at an operating frequency of 5.0 GHz. Both of these generators utilize multiline cusp permanent magnet configurations for plasma confinement and beam profile optimization. The program goals were to develop a plasma generator possessing the characteristics of high electrical efficiency (low eV/ion) and simplicity of operation while maintaining the reliability and durability of the conventional hollow cathode plasma sources. The RFI plasma generator has achieved minimum discharge losses of 120 eV/ion while the ECH generator has obtained 145 eV/ion, assuming a 90% ion optical transparency of the electrostatic acceleration system. Details of experimental tests with a variety of magnet configurations are presented.

Determination of epichlorohydrin and 1,3-dichloro-2-propanol in synthesis of cationic etherifying reagent by headspace gas chromatography.

PubMed

Tao, Zheng-Yi; Chai, Xin-Sheng; Wu, Shu-Bin

2011-09-16

This study demonstrates a headspace gas chromatographic(HS-GC) technique for the determination of residual epichlorohydrin (ECH) and generated 1,3-dichloro-2-propanol (DCP) in synthesis process of 3-chloro-2-hydroxypropyltrimethylammonium chloride (CHTAC). By a weight-based sampling method, coupled with significant dilution in 15.8% sodium sulfate and 0.1% silver nitrate mixed solution rapidly, the sample for HS-GC analysis is prepared. Based on the reaction stoichiometry, the conversion (R) of CHTAC during the synthesis process can be calculated from sampling weight and GC peak area. The results showed that the method has a good measurement precision (RSD<2.5%) and accuracy (recovery=101-104%) for the quantification of both ECH and DCP in the process samples. The present method is simple and accurate, which can be used for the efficient determination of the CHTAC conversion in the synthesis research. Copyright © 2011 Elsevier B.V. All rights reserved.

Determination of chlorinated volatile organic compounds in polyamine epichlorohydrin solution by headspace gas chromatography.

PubMed

Yan, Ning; Wan, Xiao-Fang; Chai, Xin-Sheng; Chen, Run-Quan

2017-05-05

This study demonstrated a headspace gas chromatographic (HS-GC) method for the determination of residual epichlorohydrin (ECH) and the by-product 1,3-dichloro-2-propanol (DCP) in polyamine epichlorohydrin (PAE) solution. It was based on the vapor-liquid phase equilibrium of these analytes at 60°C for 30min in a closed headspace sample vial before GC measurement. It was found that matrix of the PAE solution had the effect on the headspace equilibrium of these species and therefore a standard addition must be applied in the method validation. The results showed that the present method has a good measurement precision (RSD <2.90%) and accuracy (recoveries from 93.6 to 105%), and the limit of quantitation (LOQ) is 3.75mg/L for ECH and 0.8g/L for DCP. The present method is suitable to be used for analyzing the chlorinated volatile organic compounds in the commercial PAE resin solutions. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of low central fuelling on density and ion temperature profiles in reversed shear plasmas on JT-60U

NASA Astrophysics Data System (ADS)

Takenaga, H.; Ide, S.; Sakamoto, Y.; Fujita, T.; JT-60 Team

2008-07-01

Effects of low central fuelling on density and ion temperature profiles have been investigated using negative ion based neutral beam injection and electron cyclotron heating (ECH) in reversed shear plasmas on JT-60U. Strong internal transport barrier (ITB) was maintained in density and ion temperature profiles, when central fuelling was decreased by switching positive ion based neutral beam injection to ECH after the strong ITB formation. Similar density and ion temperature ITBs were formed for the low and high central fuelling cases during the plasma current ramp-up phase. Strong correlation between the density gradient and the ion temperature gradient was observed, indicating that particle transport and ion thermal transport are strongly coupled or the density gradient assists the ion temperature ITB formation through suppression of drift wave instabilities such as ion temperature gradient mode. These results support that the density and ion temperature ITBs can be formed under reactor relevant conditions.

Development, validation and matrix effect of a QuEChERS method for the analysis of organochlorine pesticides in fish tissue.

PubMed

Stremel, Tatiana R De O; Domingues, Cinthia E; Zittel, Rosimara; Silva, Cleber P; Weinert, Patricia L; Monteiro, Franciele C; Campos, Sandro X

2018-04-03

This study aims to develop and validate a method to determine OCPs in fish tissues, minimizing the consumption of sample and reagents, by using a modified QuEChERS along with ultrasound, d-SPE and gas chromatography with an electron capture detector (GC-ECD), refraining the pooling. Different factorial designs were employed to optimize the sample preparation phase. The validation method presented a recovery of around 77.3% and 110.8%, with RSD lower than 13% and the detection limits were between 0.24 and 2.88 μgkg -1 , revealing good sensitiveness and accuracy. The method was satisfactorily applied to the analysis of tissues from different species of fish and OCPs residues were detected. The proposed method was shown effective to determine OCPs low concentrations in fish tissues, using small sample mass (0.5 g), making the sample analyses viable without the need for grouping (pool).

Determination of 105 antibiotic, anti-inflammatory, antiparasitic agents and tranquilizers by LC-MS/MS based on an acidic QuEChERS-like extraction.

PubMed

Desmarchelier, Aurélien; Fan, Kaïli; Minh Tien, Mai; Savoy, Marie-Claude; Tarres, Adrienne; Fuger, Denis; Goyon, Alexandre; Bessaire, Thomas; Mottier, Pascal

2018-04-01

A procedure for screening 105 veterinary drugs in foods by liquid chromatography tandem mass-spectrometry (LC-MS/MS) is presented. Its scope encompasses raw materials of animal origin (milk, meat, fish, egg and fat) but also related processed ingredients and finished products commonly used and manufactured by food business operators. Due to the complexity of the matrices considered and to efficiently deal with losses during extraction and matrix effects during MS source ionisation, each sample was analysed twice, that is 'unspiked' and 'spiked at the screening target concentration' using a QuEChERS-like extraction. The entire procedure was validated according to the European Community Reference Laboratories Residues Guidelines. False-negative and false-positive rates were below 5% for all veterinary drugs whatever the food matrix. Effectiveness of the procedure was further demonstrated through participation to five proficiency tests and its ruggedness demonstrated in quality control operations by a second laboratory.

A comparison of soil moisture sensors for space flight applications

NASA Technical Reports Server (NTRS)

Norikane, J. H.; Prenger, J. J.; Rouzan-Wheeldon, D. T.; Levine, H. G.

2005-01-01

Plants will be an important part of future long-term space missions. Automated plant growth systems require accurate and reliable methods of monitoring soil moisture levels. There are a number of different methods to accomplish this task. This study evaluated sensors using the capacitance method (ECH2O), the heat-pulse method (TMAS), and tensiometers, compared to soil water loss measured gravimetrically in a side-by-side test. The experiment monitored evaporative losses from substrate compartments filled with 1- to 2-mm baked calcinated clay media. The ECH2O data correlated well with the gravimetric measurements, but over a limited range of soil moisture. The averaged TMAS sensor data overstated soil moisture content levels. The tensiometer data appeared to track evaporative losses in the 0.5- to 2.5-kPa range of matric potential that corresponds to the water content needed to grow plants. This small range is characteristic of large particle media, and thus high-resolution tensiometers are required to distinguish changing moisture contents in this range.

Fast determination of pyrethroid pesticides in tobacco by GC-MS-SIM coupled with modified QuEChERS sample preparation procedure.

PubMed

Gao, Yan; Sun, Ying; Jiang, Chunzhu; Yu, Xi; Wang, Yuanpeng; Zhang, Hanqi; Song, Daqian

2013-01-01

An analytical method was developed for the extraction and determination of pyrethroid pesticide residues in tobacco. The modified QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe) method was applied for preparing samples. In this study, methyl cyanide (MeCN)-saturated salt aqueous was used as the two-phase extraction solvent for the first time, and a vortex shaker was used for the simultaneous shaking and concentration of the analytes. The effects of experimental parameters on extraction and clean-up efficiency were investigated and optimized. The analytes were determined by gas chromatography-mass spectrometry-selected ion monitoring (GC-MS-SIM). The obtained recoveries of the analytes at three different fortification levels were 76.85-114.1% and relative standard deviations (RSDs) were lower than 15.7%. The limits of quantification (LOQs) were from 1.28 to 26.6 μg kg(-1). This method was also applied to the analysis of actual commercial tobacco products and the analytical results were satisfactory.

Verification and optimization of the CFETR baseline scenario

NASA Astrophysics Data System (ADS)

Zhao, D.; Lao, L. L.; Meneghini, O.; Staebler, G. M.; Candy, J.; Smith, S. P.; Snyder, P. B.; Prater, R.; Chen, X.; Chan, V. S.; Li, J.; Chen, J.; Shi, N.; Guo, W.; Pan, C.; Jian, X.

2016-10-01

The baseline scenario of China Fusion Engineering Test Reactor (CFETR) was designed starting from 0D calculations. The CFETR baseline scenario satisfies the minimum goal of Fusion Nuclear Science Facility aimed at bridging the gaps between ITER and DEMO. 1.5D calculations are presented to verify the on-going efforts in higher-dimensional modeling of CFETR. Steady-state scenarios are calculated self-consistently by the OMFIT integrated modeling framework that includes EFIT for equilibrium, ONETWO for sources and current, TGYRO for transport. With 68MW of neutral beam power and 8MW of ECH injected to the plasma, the average ion temperature is maintained at 15keV, while 150MW fusion power is produced. The neutral beams also drive 55% of the plasma current. Modest fast ion diffusion will reduce NBCD and affect the profile substantially. Top-launch ECH will increase the current drive and the power absorption rate. EPED model are being included. Work supported by U.S. DOE under DE-FC02-04ER54698 and the USTC CFETR contract.

Improved cross-calibration of Thomson scattering and electron cyclotron emission with ECH on DIII-D.

PubMed

Brookman, M W; Austin, M E; McLean, A G; Carlstrom, T N; Hyatt, A W; Lohr, J

2016-11-01

Thomson scattering produces n e profiles from measurement of scattered laser beam intensity. Rayleigh scattering provides a first calibration of the relation n e ∝ I TS , which depends on many factors (e.g., laser alignment and power, optics, and measurement systems). On DIII-D, the n e calibration is adjusted against an absolute n e from the density-driven cutoff of the 48 channel 2nd harmonic X-mode electron cyclotron emission system. This method has been used to calibrate Thomson n e from the edge to near the core (r/a > 0.15). Application of core electron cyclotron heating improves the quality of cutoff and depth of its penetration into the core, and also changes underlying MHD activity, minimizing crashes which confound calibration. Less fueling is needed as "ECH pump-out" generates a plasma ready to take up gas. On removal of gyrotron power, cutoff penetrates into the core as channels fall successively and smoothly into cutoff.

Fast wave direct electron heating in advanced inductive and ITER baseline scenario discharges in DIII-D

DOE PAGES

Pinsker, R. I.; Austin, M. E.; Diem, S. J.; ...

2014-02-12

Fast Wave (FW) heating and electron cyclotron heating (ECH) are used in the DIII-D tokamak to study plasmas with low applied torque and dominant electron heating characteristic of burning plasmas. FW heating via direct electron damping has reached the 2.5 MW level in high performance ELMy H-mode plasmas. In Advanced Inductive (AI) plasmas, core FW heating was found to be comparable to that of ECH, consistent with the excellent first-pass absorption of FWs predicted by ray-tracing models at high electron beta. FW heating at the ~2 MW level to ELMy H-mode discharges in the ITER Baseline Scenario (IBS) showed unexpectedlymore » strong absorption of FW power by injected neutral beam (NB) ions, indicated by significant enhancement of the D-D neutron rate, while the intended absorption on core electrons appeared rather weak. As a result, the AI and IBS discharges are compared in an effort to identify the causes of the different response to FWs.« less

Fast wave direct electron heating in advanced inductive and ITER baseline scenario discharges in DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinsker, R. I.; Jackson, G. L.; Luce, T. C.

Fast Wave (FW) heating and electron cyclotron heating (ECH) are used in the DIII-D tokamak to study plasmas with low applied torque and dominant electron heating characteristic of burning plasmas. FW heating via direct electron damping has reached the 2.5 MW level in high performance ELMy H-mode plasmas. In Advanced Inductive (AI) plasmas, core FW heating was found to be comparable to that of ECH, consistent with the excellent first-pass absorption of FWs predicted by ray-tracing models at high electron beta. FW heating at the ∼2 MW level to ELMy H-mode discharges in the ITER Baseline Scenario (IBS) showed unexpectedlymore » strong absorption of FW power by injected neutral beam (NB) ions, indicated by significant enhancement of the D-D neutron rate, while the intended absorption on core electrons appeared rather weak. The AI and IBS discharges are compared in an effort to identify the causes of the different response to FWs.« less