Toward a Reduced-Wire Readout System for Ultrasound Imaging

PubMed Central

Lim, Jaemyung; Arkan, Evren F.; Degertekin, F. Levent; Ghovanloo, Maysam

2015-01-01

We present a system-on-a-chip (SoC) for use in high-frequency capacitive micromachined ultrasonic transducer (CMUT) imaging systems. This SoC consists of trans-impedance amplifiers (TIA), delay locked loop (DLL) based clock multiplier, quadrature sampler, and pulse width modulator (PWM). The SoC down converts RF echo signal to baseband by quadrature sampling which facilitates modulation. To send data through a 1.6 m wire in the catheter which has limited bandwidth and is vulnerable to noise, the SoC creates a pseudo-digital PWM signal which can be used for back telemetry or wireless readout of the RF data. In this implementation, using a 0.35-μm std. CMOS process, the TIA and single-to-differential (STD) converter had 45 MHz bandwidth, the quadrature sampler had 10.1 dB conversion gain, and the PWM had 5-bit ENoB. Preliminary results verified front-end functionality, and the power consumption of a TIA, STD, quadrature sampler, PWM, and clock multiplier was 26 mW from a 3 V supply. PMID:25571135

Photochemistry of matrix isolated (trifluoromethyl)sulfonyl azide, CF₃SO₂N₃.

PubMed

Zeng, Xiaoqing; Beckers, Helmut; Willner, Helge; Neuhaus, Patrik; Grote, Dirk; Sander, Wolfram

2015-03-19

The photochemistry of matrix isolated (trifluoromethylsulfonyl) azide, CF3SO2N3, has been studied at low temperatures. Upon ArF laser irradiation (λ = 193 nm), the azide eliminates N2 and furnishes triplet [(trifluoromethyl)sulfonyl]nitrene, CF3SO2N, which has been characterized by IR and EPR spectroscopy. Upon subsequent UV light irradiation (λ = 260-400 nm) the nitrene converts to CF3N═SO2 and CF3S(O)NO through a Curtius-type rearrangement. Further two new species CF2N═SO2F and FSNO were identified together with CF2NF, SO2, F2CO, CF3NO, and SO as side products. In addition, triplet nitrene CF3N was detected by its EPR and IR spectra. The complex stepwise photodecomposition of matrix isolated CF3SO2N3 is discussed in terms of the observed photolysis products and quantum chemical calculations.

Voting patterns and alliance formation in the European Parliament

PubMed Central

Hix, Simon; Noury, Abdul; Roland, Gérard

2008-01-01

Members of the European Parliament (MEPs) have voluntarily formed transnational political groups and invariably follow the voting instructions of these groups. This is intriguing as there are few obvious incentives for doing so. Unlike national parties, for example, the political groups in the European Parliament are not punished by the electorate if they are divided on key issues, as citizens know very little about what goes on inside the European Parliament. This paper pieces together an explanation of why the European political groups exist and why they have become so powerful by looking at the determinants of group cohesion and by undertaking a spatial analysis of voting in the European Parliament. MEPs who share preferences on a range of issues on the European Union policy agenda have an incentive to establish a division-of-labour contract and to share the costs of collecting information. Once internal party policy specialization and agenda setting has been established, MEPs have incentives to follow the voting instructions of their group owing to the advantages of cohesion in a context of repeated voting. PMID:19073477

Voting patterns and alliance formation in the European Parliament.

PubMed

Hix, Simon; Noury, Abdul; Roland, Gérard

2009-03-27

Members of the European Parliament (MEPs) have voluntarily formed transnational political groups and invariably follow the voting instructions of these groups. This is intriguing as there are few obvious incentives for doing so. Unlike national parties, for example, the political groups in the European Parliament are not punished by the electorate if they are divided on key issues, as citizens know very little about what goes on inside the European Parliament. This paper pieces together an explanation of why the European political groups exist and why they have become so powerful by looking at the determinants of group cohesion and by undertaking a spatial analysis of voting in the European Parliament. MEPs who share preferences on a range of issues on the European Union policy agenda have an incentive to establish a division-of-labour contract and to share the costs of collecting information. Once internal party policy specialization and agenda setting has been established, MEPs have incentives to follow the voting instructions of their group owing to the advantages of cohesion in a context of repeated voting.

Wavelength-independent all-fiber mode converters.

PubMed

Lai, K; Leon-Saval, S G; Witkowska, A; Wadsworth, W J; Birks, T A

2007-02-15

We have used two different photonic crystal fiber (PCF) techniques to make all-fiber mode converters. An LP(01) to LP(11) mode converter was made by the ferrule technique on a drawing tower, and an LP(01) to LP(02) mode converter was made by controlled hole inflation of an existing PCF on a tapering rig. Both devices rely on adiabatic propagation rather than resonant coupling; so high extinction was achieved across a wide wavelength range.

Liquefaction process

DOEpatents

Gorbaty, Martin L.; Stone, John B.; Poddar, Syamal K.

1982-01-01

Scale formation during the liquefaction of lower ranking coals and similar carbonaceous materials is significantly reduced and/or prevented by pretreatment with a combination of pretreating agents comprising SO.sub.2 and an oxidizing agent. The pretreatment is believed to convert at least a portion of the scale-forming components and particularly calcium, to the corresponding sulfate prior to liquefaction. The pretreatment may be accomplished with the combination of pretreating agents either simultaneously by using a mixture comprising SO.sub.2 and an oxidizing agent or sequentially by first treating with SO.sub.2 and then with an oxidizing agent.

Sulfur Dioxide and the Production of Sulfuric Acid on Present-Day and Early Mars: Implications for the Lack of Detected Carbonates on the Surface

NASA Technical Reports Server (NTRS)

Levine, Joel S.; Summers, Michael E.

2008-01-01

In the early history of Mars, volcanic activity associated with the formation of the Tharsis ridge produced a very large amount of atmospheric SO2--on the order of a bar of atmospheric SO2. In the present-day atmosphere of Mars, the lifetime of SO2 is relatively short with a lifetime of less than a day. The short lifetime of SO2 in the present Mars atmosphere makes the production of significant levels of H2SO4 very difficult since the SO2 may be destroyed by various chemical and photochemical processes before the SO2 can be converted to H2SO4. However, photochemical calculations performed and described here, indicate that enhanced atmospheric levels of CO2 in the early atmosphere of Mars resulted in a significantly enhanced atmospheric lifetime for SO2 up to several years. With a significantly enhanced atmospheric lifetime, SO2 could readily form large amounts of H2SO4, which precipitated out of the atmosphere in the form of droplets. The precipitated H2SO4 then reacted with potential surface carbonates, destroying the carbonates and resulting in the abundant and widespread distribution of sulfates on the surface of Mars as detected by recent Mars missions.

40 CFR 60.101a - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... system may have an overpressure vent to a flare but the primary purpose for a fuel gas system is to... emissions from sulfur recovery plants by converting these emissions to sulfur dioxide (SO2) and recycling... reduces emissions from sulfur recovery plants by converting these emissions to H2S and either recycling...

40 CFR 60.101a - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... system may have an overpressure vent to a flare but the primary purpose for a fuel gas system is to... emissions from sulfur recovery plants by converting these emissions to sulfur dioxide (SO2) and recycling... reduces emissions from sulfur recovery plants by converting these emissions to H2S and either recycling...

Fluid bed gasification – Plasma converter process generating energy from solid waste: Experimental assessment of sulphur species

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morrin, Shane, E-mail: shane.morrin@ucl.ac.uk; Advanced Plasma Power, Swindon, Wiltshire SN3 4DE; Lettieri, Paola, E-mail: p.lettieri@ucl.ac.uk

2014-01-15

Highlights: • We investigate gaseous sulphur species whilst gasifying sulphur-enriched wood pellets. • Experiments performed using a two stage fluid bed gasifier – plasma converter process. • Notable SO{sub 2} and relatively low COS levels were identified. • Oxygen-rich regions of the bed are believed to facilitate SO{sub 2}, with a delayed release. • Gas phase reducing regions above the bed would facilitate more prompt COS generation. - Abstract: Often perceived as a Cinderella material, there is growing appreciation for solid waste as a renewable content thermal process feed. Nonetheless, research on solid waste gasification and sulphur mechanisms in particularmore » is lacking. This paper presents results from two related experiments on a novel two stage gasification process, at demonstration scale, using a sulphur-enriched wood pellet feed. Notable SO{sub 2} and relatively low COS levels (before gas cleaning) were interesting features of the trials, and not normally expected under reducing gasification conditions. Analysis suggests that localised oxygen rich regions within the fluid bed played a role in SO{sub 2}’s generation. The response of COS to sulphur in the feed was quite prompt, whereas SO{sub 2} was more delayed. It is proposed that the bed material sequestered sulphur from the feed, later aiding SO{sub 2} generation. The more reducing gas phase regions above the bed would have facilitated COS – hence its faster response. These results provide a useful insight, with further analysis on a suite of performed experiments underway, along with thermodynamic modelling.« less

Analysis of high voltage step-up nonisolated DC-DC boost converters

NASA Astrophysics Data System (ADS)

Alisson Alencar Freitas, Antônio; Lessa Tofoli, Fernando; Junior, Edilson Mineiro Sá; Daher, Sergio; Antunes, Fernando Luiz Marcelo

2016-05-01

A high voltage step-up nonisolated DC-DC converter based on coupled inductors suitable to photovoltaic (PV) systems applications is proposed in this paper. Considering that numerous approaches exist to extend the voltage conversion ratio of DC-DC converters that do not use transformers, a detailed comparison is also presented among the proposed converter and other popular topologies such as the conventional boost converter and the quadratic boost converter. The qualitative analysis of the coupled-inductor-based topology is developed so that a design procedure can be obtained, from which an experimental prototype is implemented to validate the theoretical assumptions.

Characterization of transimpedance amplifier as optical to electrical converter on designing optical instrumentation

NASA Astrophysics Data System (ADS)

Hanto, D.; Ula, R. K.

2017-05-01

Optical to electrical converter is the main components for designing of the optical instrumentations. In addition, this component is also used as signal conditioning. This component usually consists of a photo detector and amplifier. In this paper, characteristics of commercial amplifiers from Thorlabs PDA50B-EC has been observed. The experiment was conducted by diode laser with power of -5 dBm and wavelength 1310 nm; the optical attenuator to vary optical power from 0 to 60 dB, optical to electrical converter from Thorlabs Amplifier PDA50B-EC; multimode optical fiber to guide the laser; and digital voltmeter to measure the output of converter. The results of the characterization indicate that each channel amplification has a non-linear correlation between optical and electrical parameter; optical conversion measurement range of 20-23 dB to full scale; and different measurement coverage area. If this converter will be used as a part component of optical instrumentation so it should be adjusted suitably with the optical power source. Then, because of the correlation equation is not linear so calculation to determine the interpretation also should be considered in addition to the transfer function of the optical sensor.

SEMICONDUCTOR INTEGRATED CIRCUITS A 10-bit 200-kS/s SAR ADC IP core for a touch screen SoC

NASA Astrophysics Data System (ADS)

Xingyuan, Tong; Yintang, Yang; Zhangming, Zhu; Wenfang, Sheng

2010-10-01

Based on a 5 MSBs (most-significant-bits)-plus-5 LSBs (least-significant-bits) C-R hybrid D/A conversion and low-offset pseudo-differential comparison approach, with capacitor array axially symmetric layout topology and resistor string low gradient mismatch placement method, an 8-channel 10-bit 200-kS/s SAR ADC (successive-approximation-register analog-to-digital converter) IP core for a touch screen SoC (system-on-chip) is implemented in a 0.18 μm 1P5M CMOS logic process. Design considerations for the touch screen SAR ADC are included. With a 1.8 V power supply, the DNL (differential non-linearity) and INL (integral non-linearity) of this converter are measured to be about 0.32 LSB and 0.81 LSB respectively. With an input frequency of 91 kHz at 200-kS/s sampling rate, the spurious-free dynamic range and effective-number-of-bits are measured to be 63.2 dB and 9.15 bits respectively, and the power is about 136 μW. This converter occupies an area of about 0.08 mm2. The design results show that it is very suitable for touch screen SoC applications.

Validating the accuracy of SO2 gas retrievals in the thermal infrared (8-14 μm)

NASA Astrophysics Data System (ADS)

Gabrieli, Andrea; Porter, John N.; Wright, Robert; Lucey, Paul G.

2017-11-01

Quantifying sulfur dioxide (SO2) in volcanic plumes is important for eruption predictions and public health. Ground-based remote sensing of spectral radiance of plumes contains information on the path-concentration of SO2. However, reliable inversion algorithms are needed to convert plume spectral radiance measurements into SO2 path-concentrations. Various techniques have been used for this purpose. Recent approaches have employed thermal infrared (TIR) imaging between 8 μm and 14 μm to provide two-dimensional mapping of plume SO2 path-concentration, using what might be described as "dual-view" techniques. In this case, the radiance (or its surrogate brightness temperature) is computed for portions of the image that correspond to the plume and compared with spectral radiance obtained for adjacent regions of the image that do not (i.e., "clear sky"). In this way, the contribution that the plume makes to the measured radiance can be isolated from the background atmospheric contribution, this residual signal being converted to an estimate of gas path-concentration via radiative transfer modeling. These dual-view approaches suffer from several issues, mainly the assumption of clear sky background conditions. At this time, the various inversion algorithms remain poorly validated. This paper makes two contributions. Firstly, it validates the aforementioned dual-view approaches, using hyperspectral TIR imaging data. Secondly, it introduces a new method to derive SO2 path-concentrations, which allows for single point SO2 path-concentration retrievals, suitable for hyperspectral imaging with clear or cloudy background conditions. The SO2 amenable lookup table algorithm (SO2-ALTA) uses the MODTRAN5 radiative transfer model to compute radiance for a variety (millions) of plume and atmospheric conditions. Rather than searching this lookup table to find the best fit for each measured spectrum, the lookup table was used to train a partial least square regression (PLSR) model. The coefficients of this model are used to invert measured radiance spectra to path-concentration on a pixel-by-pixel basis. In order to validate the algorithms, TIR hyperspectral measurements were carried out by measuring sky radiance when looking through gas cells filled with known amounts of SO2. SO2-ALTA was also tested on retrieving SO2 path-concentrations from the Kīlauea volcano, Hawai'i. For cloud-free conditions, all three techniques worked well. In cases where background clouds were present, then only SO2-ALTA was found to provide good results, but only under low atmospheric water vapor column amounts.

FY-15 Progress Report on Cleanup of irradiated SHINE Target Solutions Containing 140g-U/L Uranyl Sulfate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, Megan E.; Bowers, Delbert L.; Vandegrift, George F.

2015-09-01

During FY 2012 and 2013, a process was developed to convert the SHINE Target Solution (STS) of irradiated uranyl sulfate (140 g U/L) to uranyl nitrate. This process is necessary so that the uranium solution can be processed by the UREX (Uranium Extraction) separation process, which will remove impurities from the uranium so that it can be recycled. The uranyl sulfate solution must contain <0.02 M SO 4 2- so that the uranium will be extractable into the UREXsolvent. In addition, it is desired that the barium content be below 0.0007 M, as this is the limit in the Resourcemore » Conservation and Recovery Act (RCRA).« less

47 CFR 15.121 - Scanning receivers and frequency converters used with scanning receivers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... transmissions to analog voice audio. (2) Be designed so that the tuning, control and filtering circuitry is inaccessible. The design must be such that any attempts to modify the equipment to receive transmissions from... Radiotelephone Service transmissions. (e) Scanning receivers and frequency converters designed for use with...

47 CFR 15.121 - Scanning receivers and frequency converters used with scanning receivers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... transmissions to analog voice audio. (2) Be designed so that the tuning, control and filtering circuitry is inaccessible. The design must be such that any attempts to modify the equipment to receive transmissions from... Radiotelephone Service transmissions. (e) Scanning receivers and frequency converters designed for use with...

47 CFR 15.121 - Scanning receivers and frequency converters used with scanning receivers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... transmissions to analog voice audio. (2) Be designed so that the tuning, control and filtering circuitry is inaccessible. The design must be such that any attempts to modify the equipment to receive transmissions from... Radiotelephone Service transmissions. (e) Scanning receivers and frequency converters designed for use with...

47 CFR 15.121 - Scanning receivers and frequency converters used with scanning receivers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... transmissions to analog voice audio. (2) Be designed so that the tuning, control and filtering circuitry is inaccessible. The design must be such that any attempts to modify the equipment to receive transmissions from... Radiotelephone Service transmissions. (e) Scanning receivers and frequency converters designed for use with...

Electrodialysis-based separation process for salt recovery and recycling from waste water

DOEpatents

Tsai, S.P.

1997-07-08

A method for recovering salt from a process stream containing organic contaminants is provided, comprising directing the waste stream to a desalting electrodialysis unit so as to create a concentrated and purified salt permeate and an organic contaminants-containing stream, and contacting said concentrated salt permeate to a water-splitting electrodialysis unit so as to convert the salt to its corresponding base and acid. 6 figs.

Electrodialysis-based separation process for salt recovery and recycling from waste water

DOEpatents

Tsai, Shih-Perng

1997-01-01

A method for recovering salt from a process stream containing organic contaminants is provided, comprising directing the waste stream to a desalting electrodialysis unit so as to create a concentrated and purified salt permeate and an organic contaminants containing stream, and contacting said concentrated salt permeate to a water-splitting electrodialysis unit so as to convert the salt to its corresponding base and acid.

All-fiber mode converter based on superimposed long period fiber gratings

NASA Astrophysics Data System (ADS)

Xue, Yan-ru; Bi, Wei-hong; Jin, Wa; Tian, Peng-fei; Jiang, Peng; Liu, Qiang; Jin, Yun

2018-03-01

In this paper, a novel broadband all-fiber mode converter is proposed and experimentally demonstrated. Through writing a pair of superimposed long period fiber gratings (SLPFGs) in tow-mode fiber (TMF) with a CO2 laser, the mode converter can realize the conversion from LP01 to LP11 owing to the phase matching condition. Numerical and experimental results show that the bandwidth of this mode converter is 3 times broader than that of a single grating converter. The converter has low loss, high coupling efficiency, small size and is easy to fabricate, so it can be widely used in mode-division multiplexing.

Optical apparatus for conversion of whispering-gallery modes into a free space gaussian like beam

DOEpatents

Stallard, Barry W.; Makowski, Michael A.; Byers, Jack A.

1992-01-01

An optical converter for efficient conversion of millimeter wavelength whispering-gallery gyrotron output into a linearly polarized, free-space Gaussian-like beam. The converter uses a mode-converting taper and three mirror optics. The first mirror has an azimuthal tilt to eliminate the k.sub..phi. component of the propagation vector of the gyrotron output beam. The second mirror has a twist reflector to linearly polarize the beam. The third mirror has a constant phase surface so the converter output is in phase.

Novel Acid Catalysts from Waste-Tire-Derived Carbon: Application in Waste-to-Biofuel Conversion

DOE PAGES

Hood, Zachary D.; Adhikari, Shiba P.; Li, Yunchao; ...

2017-06-21

Many inexpensive biofuel feedstocks, including those containing free fatty acids (FFAs) in high concentrations, are typically disposed of as waste due to our inability to efficiently convert them into usable biofuels. Here we demonstrate that carbon derived from waste tires could be functionalized with sulfonic acid (-SO 3H) to effectively catalyze the esterification of oleic acid or a mixture of fatty acids to usable biofuels. Waste tires were converted to hard carbon, then functionalized with catalytically active -SO 3H groups on the surface through an environmentally benign process that involved the sequential treatment with L-cysteine, dithiothreitol, and H 2O 2.more » In conclusion, when benchmarked against the same waste-tire derived carbon material treated with concentrated sulfuric acid at 150 °C, similar catalytic activity was observed. Both catalysts could also effectively convert oleic acid or a mixture of fatty acids and soybean oil to usable biofuels at 65 °C and 1 atm without leaching of the catalytic sites.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hood, Zachary D.; Adhikari, Shiba P.; Li, Yunchao

Many inexpensive biofuel feedstocks, including those containing free fatty acids (FFAs) in high concentrations, are typically disposed of as waste due to our inability to efficiently convert them into usable biofuels. Here we demonstrate that carbon derived from waste tires could be functionalized with sulfonic acid (-SO 3H) to effectively catalyze the esterification of oleic acid or a mixture of fatty acids to usable biofuels. Waste tires were converted to hard carbon, then functionalized with catalytically active -SO 3H groups on the surface through an environmentally benign process that involved the sequential treatment with L-cysteine, dithiothreitol, and H 2O 2.more » In conclusion, when benchmarked against the same waste-tire derived carbon material treated with concentrated sulfuric acid at 150 °C, similar catalytic activity was observed. Both catalysts could also effectively convert oleic acid or a mixture of fatty acids and soybean oil to usable biofuels at 65 °C and 1 atm without leaching of the catalytic sites.« less

Bidirectional control system for energy flow in solar powered flywheel

NASA Technical Reports Server (NTRS)

Nola, Frank J. (Inventor)

1987-01-01

An energy storage system for a spacecraft is provided which employs a solar powered flywheel arrangement including a motor/generator which, in different operating modes, drives the flywheel and is driven thereby. A control circuit, including a threshold comparator, senses the output of a solar energy converter, and when a threshold voltage is exceeded thereby indicating the availability of solar power for the spacecraft loads, activates a speed control loop including the motor/generator so as to accelerate the flywheel to a constant speed and thereby store mechanical energy, while also supplying energy from the solar converter to the loads. Under circumstances where solar energy is not available and thus the threshold voltage is not exceeded, the control circuit deactivates the speed control loop and activates a voltage control loop that provides for operation of the motor as a generator so that mechanical energy from the flywheel is converted into electrical energy for supply to the spacecraft loads.

Converting inert plastic waste into energetic materials: A study on the light-accelerated decomposition of plastic waste with the Fenton reaction.

PubMed

Chow, Cheuk-Fai; Wong, Wing-Leung; Chan, Ching-Wan; Chan, Chung-Sum

2018-05-01

Better treatment and management strategies than landfilling are needed to address the large quantities of unrecycled plastic waste generated by daily human activities. Waste-to-energy conversion is an ideal benchmark for developing future large-scale waste management technologies. The present study explores a new approach for producing energetic materials by converting inert plastic waste into energy (thermal and mechanical energies) via a light-controlled process through the simple chemical activation of plastic waste, including polyethylene, polypropylene, and polyvinyl chloride. The inert and non-polar polymer surfaces of the plastics were modified by generating a number of sulfonic groups (SO 3 - ) using chlorosulfuric acid, followed by grafting of Fe(III) catalyst onto the polymer chains to obtain activated polymer. Elemental analyses of these activated materials showed that the carbon-to-sulfur ratio ranged from 3:1 to 5:1. The FTIR spectra indicated the presence of CC bonds (v C=C : 1615-1630 cm -1 ) and SO bonds (v S=O : 1151-1167 cm -1 ) in the activated polymers after chemical reaction. These activated materials were energetic, as light could be used to convert them into thermal (1800-3200 J/g) and mechanical energies (380-560 kPa/g) using hydrogen peroxide as the oxidant under ambient conditions within 1 h. Copyright © 2018 Elsevier Ltd. All rights reserved.

Role of Inherent Inorganic Constituents in SO2 Sorption Ability of Biochars Derived from Three Biomass Wastes.

PubMed

Xu, Xiaoyun; Huang, Daxuan; Zhao, Ling; Kan, Yue; Cao, Xinde

2016-12-06

Biochar is rich in both organic carbon and inorganic components. Extensive work has attributed the high sorption ability of biochar to the pore structure and surface chemical property related to its organic carbon fraction. In this study, three biochars derived from dairy manure (DM-biochar), sewage sludge (SS-biochar), and rice husk (RH-biochar), respectively, were evaluated for their SO 2 sorption behavior and the underlying mechanisms, especially the role of inherent inorganic constituents. The sorption capacities of SO 2 by the three biochars were 8.87-15.9 mg g -1 . With the moisture content increasing from 0% to 50%, the sorption capacities increased by up to about 3 times, mainly due to the formation of alkaline water membrane on the biochar surface which could promote the sorption and transformation of acidic SO 2 . DM- and SS-biochar containing larger mineral constituents showed higher sorption capacity for SO 2 than RH-biochar containing less mineral components. CaCO 3 and Ca 3 (PO 4 ) 2 in DM-biochar induced sorbed SO 2 transformation into K 2 Ca(SO 4 ) 2 ·H 2 O and CaSO 4 ·2H 2 O, while the sorbed SO 2 was converted to Fe 2 (SO 4 ) 3 ·H 2 SO 4 ·2H 2 O, CaSO 4 ·2H 2 O, and Ca 3 (SO 3 ) 2 SO 4 ·12H 2 O in SS-biochar. For RH-biochar, K 3 H(SO 4 ) 2 might exist in the exhausted samples. Overall, the chemical transformation of SO 2 induced by biochar inherent mineral components occupied 44.6%-85.5% of the total SO 2 sorption. The results obtained from this study demonstrated that biochar as a unique carbonaceous material could distinctly be a promising sorbent for acidic SO 2 removal in which the inorganic components played an important role in the SO 2 sorption and transformation.

Impact winter and the Cretaceous/Tertiary extinctions: Results of a Chicxulub asteroid impact model

NASA Technical Reports Server (NTRS)

Pope, Kevin O.; Baines, Kevin H.; Ocampo, Adriana C.; Ivanov, Boris A.

1994-01-01

The Chicxulub impact crater in Mexico is the site of the impact purported to have caused mass extinctions at the Cretaceous/Tertiary (K/T) boundary. 2-D hydrocode modeling of the impact, coupled with studies of the impact site geology, indiate that between 0.4 and 7.0 x 10(exp 17) g of sulfur were vaporized by the impact into anhydrite target rocks. A small portion of the sulfur was released as SO3 or SO4, which converted rapidly into H2SO4 aerosol and fell as acid rain. A radiative transfer model, coupled with a model of coagulation indicates that the aerosol prolonged the initial blackout period caused by impact dust only if the aerosol contained impurities. A larger portion of sulfur was released as SO2, which converted to aerosol slowly, due to the rate-limiting oxidation of SO2. Our radiative transfer calculations, combined with rates of acid production, coagulation, and diffusion indicate that solar transmission was reduced to 10-20% of normal for a period of 8-13 yr. This reduction produced a climate forcing (cooling) of -300 W/sq.m, which far exceeded the +8 W/sq.m greenhouse warming, caused by the CO2 released through the vaporization of carbonates, and therefore produced a decade of freezing and near-freezing temperatures. Several decades of moderate warming followed the decade of severe cooling due to the long residence time of CO2. The prolonged impact winter may have been a major cause of the K/T extinctions.

Mechanical drive for blood pump

DOEpatents

Bifano, N.J.; Pouchot, W.D.

1975-07-29

This patent relates to a highly efficient blood pump to be used as a replacement for a ventricle of the human heart to restore people disabled by heart disease. The mechanical drive of the present invention is designed to operate in conjunction with a thermoelectric converter power source. The mechanical drive system essentially converts the output of a rotary power into pulsatile motion so that the power demand from the thermoelectric converter remains essentially constant while the blood pump output is pulsed. (auth)

License Agreements | NCI Technology Transfer Center | TTC

Cancer.gov

NCI Technology Transfer Center (TTC) licenses the discoveries of NCI and nine other NIH Institutes so new technologies can be developed and commercialized, to convert them into public health benefits.

Biological conversion of anglesite (PbSO(4)) and lead waste from spent car batteries to galena (PbS).

PubMed

Weijma, Jan; De Hoop, Klaas; Bosma, Wobby; Dijkman, Henk

2002-01-01

Lead paste, a solid mixture containing PbSO(4), PbO(2), PbO/Pb(OH)(2) precipitate, and elemental Pb, is one of the main waste fractions from spent car batteries. Biological sulfidation represents a new process for recovery of lead from this waste. In this process the lead salts in lead paste are converted to galena (PbS) by sulfate-reducing bacteria. This paper investigates a continuous process for sulfidation of anglesite (PbSO(4)), the main constituent of lead paste, and lead paste, consisting of a laboratory-scale gas-lift bioreactor to which a slurry of anglesite or lead paste was supplied. Sulfate or elemental sulfur was added as an additional sulfur source. Hydrogen gas served as an electron donor for the biological reduction of sulfate and elemental sulfur to sulfide by sulfate- and sulfur-reducing bacteria. Anglesite was almost completely converted to galena at a loading rate of 19 kg of PbSO(4) m(-)(3) day(-)(1), producing a sludge of which the crystalline lead phases consisted of >98% PbS (galena) and 1-2% elemental Pb. With lead paste, stable sulfidation rates of up to 17 kg of lead paste m(-)(3) day(-)(1) were demonstrated, producing a sludge of which the crystalline lead phases consisted of an estimated >96% PbS, 1-2% elemental Pb, and 1-2% PbO(2).

Development of predictive pharmacophore model for in silico screening, and 3D QSAR CoMFA and CoMSIA studies for lead optimization, for designing of potent tumor necrosis factor alpha converting enzyme inhibitors

NASA Astrophysics Data System (ADS)

Murumkar, Prashant Revan; Zambre, Vishal Prakash; Yadav, Mange Ram

2010-02-01

A chemical feature-based pharmacophore model was developed for Tumor Necrosis Factor-α converting enzyme (TACE) inhibitors. A five point pharmacophore model having two hydrogen bond acceptors (A), one hydrogen bond donor (D) and two aromatic rings (R) with discrete geometries as pharmacophoric features was developed. The pharmacophore model so generated was then utilized for in silico screening of a database. The pharmacophore model so developed was validated by using four compounds having proven TACE inhibitory activity which were grafted into the database. These compounds mapped well onto the five listed pharmacophoric features. This validated pharmacophore model was also used for alignment of molecules in CoMFA and CoMSIA analysis. The contour maps of the CoMFA/CoMSIA models were utilized to provide structural insight for activity improvement of potential novel TACE inhibitors. The pharmacophore model so developed could be used for in silico screening of any commercial/in house database for identification of TACE inhibiting lead compounds, and the leads so identified could be optimized using the developed CoMSIA model. The present work highlights the tremendous potential of the two mutually complementary ligand-based drug designing techniques (i.e. pharmacophore mapping and 3D-QSAR analysis) using TACE inhibitors as prototype biologically active molecules.

Carbon-catalyzed oxidation of SO2 by NO2 and air

NASA Technical Reports Server (NTRS)

Rogowski, R. S.; Schryer, D. R.; Cofer, W. R., III; Edahl, R. A., Jr.; Munavalli, S.

1982-01-01

A series of experiments was performed using carbon particles (commercial furnace black) as a surrogate for soot particles. Carbon particles were suspended in water, and gas mixtures were bubbled into the suspensions to observe the effect of carbon particles on the oxidation of SO2 by air and NO2. Identical gas mixtures were bubbled into a blank containing only pure water. After exposure each solution was analyzed for pH and sulfate. It was found that NO2 greatly enhances the oxidation of SO2 to sulfate in the presence of carbon particles. The amount of sulfate found in the blanks was significantly less. Under the conditions of these experiments no saturation of the reaction was observed and SO2 was converted to sulfate even in a highly acid medium (pH or = 1.5).

Oxidation of SO2 by NO2 and air in an aqueous suspension of carbon

NASA Technical Reports Server (NTRS)

Rogowski, R. S.; Schryer, D. R.; Cofer, W. R., III; Edahl, R. A., Jr.; Munavalli, S.

1982-01-01

A series of experiments has been performed using carbon black as a surrogate for soot particles. Carbon black was suspended in water and gas mixtures were bubbled into the suspensions to observe the effect of carbon particles on the oxidation of SO2 by air and NO2. Identical gas mixtures were bubbled into a black containing only pure water. After exposure each solution was analyzed for pH and sulfate. It was found that NO2 greatly enhances the oxidation of SO2 to sulfate in the presence of carbon black. The amount of sulfate in the blanks was significantly less. Under the conditions of the experiments no saturation of the reaction was observed and SO2 was converted to sulfate even in a highly acid medium (pH not less than 1.5).

Reactive collisions of sulfur dioxide with molten carbonates

PubMed Central

Krebs, Thomas; Nathanson, Gilbert M.

2010-01-01

Molecular beam scattering experiments are used to investigate reactions of SO2 at the surface of a molten alkali carbonate eutectic at 683 K. We find that two-thirds of the SO2 molecules that thermalize at the surface of the melt are converted to gaseous CO2 via the reaction . The CO2 product is formed from SO2 in less than 10-6 s, implying that the reaction takes place in a shallow liquid region less than 100 Å deep. The reaction probability does not vary between 683 and 883 K, further implying a compensation between decreasing SO2 residence time in the near-interfacial region and increasing reactivity at higher temperatures. These results demonstrate the remarkable efficiency of SO2 → CO2 conversion by molten carbonates, which appear to be much more reactive than dry calcium carbonate or wet slurries commonly used for flue gas desulfurization in coal-burning power plants. PMID:20133648

Multiphase oxidation of SO2 by NO2 on CaCO3 particles

NASA Astrophysics Data System (ADS)

Zhao, Defeng; Song, Xiaojuan; Zhu, Tong; Zhang, Zefeng; Liu, Yingjun; Shang, Jing

2018-02-01

Heterogeneous/multiphase oxidation of SO2 by NO2 on solid or aqueous particles is thought to be a potentially important source of sulfate in the atmosphere, for example, during heavily polluted episodes (haze), but the reaction mechanism and rate are uncertain. In this study, in order to assess the importance of the direct oxidation of SO2 by NO2 we investigated the heterogeneous/multiphase reaction of SO2 with NO2 on individual CaCO3 particles in N2 using Micro-Raman spectroscopy. In the SO2 / NO2 / H2O / N2 gas mixture, the CaCO3 solid particle was first converted to the Ca(NO3)2 droplet by the reaction with NO2 and the deliquescence of Ca(NO3)2, and then NO2 oxidized SO2 in the Ca(NO3)2 droplet forming CaSO4, which appeared as needle-shaped crystals. Sulfate was mainly formed after the complete conversion of CaCO3 to Ca(NO3)2, that is, during the multiphase oxidation of SO2 by NO2. The precipitation of CaSO4 from the droplet solution promoted sulfate formation. The reactive uptake coefficient of SO2 for sulfate formation is on the order of 10-8, and RH enhanced the uptake coefficient. We estimate that the direct multiphase oxidation of SO2 by NO2 is not an important source of sulfate in the ambient atmosphere compared with the SO2 oxidation by OH in the gas phase and is not as important as other aqueous-phase pathways, such as the reactions of SO2 with H2O2, O3, and O2, with or without transition metals.

Decreased atmospheric sulfur deposition across the southeastern U.S.: When will watersheds release stored sulfate?

USGS Publications Warehouse

Rice, Karen C.; Scanlon, Todd M.; Lynch, Jason A.; Cosby, Bernard J.

2014-01-01

Emissions of sulfur dioxide (SO2) to the atmosphere lead to atmospheric deposition of sulfate (SO42-), which is the dominant strong acid anion causing acidification of surface waters and soils in the eastern United States (U.S.). Since passage of the Clean Air Act and its Amendments, atmospheric deposition of SO2 in this region has declined by over 80%, but few corresponding decreases in stream-water SO42- concentrations have been observed in unglaciated watersheds. We calculated SO42- mass balances for 27 forested, unglaciated watersheds from Pennsylvania to Georgia, by using total atmospheric deposition (wet plus dry) as input. Many of these watersheds still retain SO42-, unlike their counterparts in the northeastern U.S. and southern Canada. Our analysis showed that many of these watersheds should convert from retaining to releasing SO42- over the next two decades. The specific years when the watersheds crossover from retaining to releasing SO42- correspond to a general geographical pattern of later net watershed release from north to south. The single most important variable that explained the crossover year was the runoff ratio, defined as the ratio of annual mean stream discharge to precipitation. Percent clay content and mean soil depth were secondary factors in predicting crossover year. The conversion of watersheds from net SO42- retention to release anticipates more widespread reductions in stream-water SO42- concentrations in this region.

Decreased atmospheric sulfur deposition across the Southeastern U.S.: when will watersheds release stored sulfate?

PubMed

Rice, Karen C; Scanlon, Todd M; Lynch, Jason A; Cosby, Bernard J

2014-09-02

Emissions of sulfur dioxide (SO2) to the atmosphere lead to atmospheric deposition of sulfate (SO4(2-)), which is the dominant strong acid anion causing acidification of surface waters and soils in the eastern United States. Since passage of the Clean Air Act and its Amendments, atmospheric deposition of SO2 in this region has declined by over 80%, but few corresponding decreases in streamwater SO4(2-) concentrations have been observed in unglaciated watersheds. We calculated SO4(2-) mass balances for 27 forested, unglaciated watersheds from Pennsylvania to Georgia, by using total atmospheric deposition (wet plus dry) as input. Many of these watersheds still retain SO4(2-), unlike their counterparts in the northeastern U.S. and southern Canada. Our analysis showed that many of these watersheds should convert from retaining to releasing SO4(2-) over the next two decades. The specific years when the watersheds crossover from retaining to releasing SO4(2-) correspond to a general geographical pattern of later net watershed release from north to south. The single most important variable that explained the crossover year was the runoff ratio, defined as the ratio of annual mean stream discharge to precipitation. Percent clay content and mean soil depth were secondary factors in predicting crossover year. The conversion of watersheds from net SO4(2-) retention to release anticipates more widespread reductions in streamwater SO4(2-) concentrations in this region.

Quasi-multi-pulse voltage source converter design with two control degrees of freedom

NASA Astrophysics Data System (ADS)

Vural, A. M.; Bayindir, K. C.

2015-05-01

In this article, the design details of a quasi-multi-pulse voltage source converter (VSC) switched at line frequency of 50 Hz are given in a step-by-step process. The proposed converter is comprised of four 12-pulse converter units, which is suitable for the simulation of single-/multi-converter flexible alternating current transmission system devices as well as high voltage direct current systems operating at the transmission level. The magnetic interface of the converter is originally designed with given all parameters for 100 MVA operation. The so-called two-angle control method is adopted to control the voltage magnitude and the phase angle of the converter independently. PSCAD simulation results verify both four-quadrant converter operation and closed-loop control of the converter operated as static synchronous compensator (STATCOM).

East Europe Report.

DTIC Science & Technology

1986-06-19

deputy chairman. 74. Vidin Electoral District. Kiril Dimitrov Zarev, BCP Central Committee secretary. 75. Vidin Electoral District. Georgi Vulkanov...Blagoevgrad. 4. Simitli Electoral District. Boris Dimitrov Karanfilov, BCP Central Committee member, deputy minister of national defense. 5. Strumyan...Electoral District. Emiliya Mircheva Kostova, chairman okrug BZNS management. 6. Sandanski Electoral District. Lalyu Ivanov Dimitrov , BCP Central

Regulated dc-to-dc converter for voltage step-up or step-down with input-output isolation

NASA Technical Reports Server (NTRS)

Feng, S. Y.; Wilson, T. G. (Inventor)

1973-01-01

A closed loop regulated dc-to-dc converter employing an unregulated two winding inductive energy storage converter is provided by using a magnetically coupled multivibrator acting as duty cycle generator to drive the converter. The multivibrator is comprised of two transistor switches and a saturable transformer. The output of the converter is compared with a reference in a comparator which transmits a binary zero until the output exceeds the reference. When the output exceeds the reference, the binary output of the comparator drives transistor switches to turn the multivibrator off. The multivibrator is unbalanced so that a predetermined transistor will always turn on first when the binary feedback signal becomes zero.

Chemical conversion of sulphur dioxide on Eyjafjallajökull's volcanic ash from the 2010 eruption

NASA Astrophysics Data System (ADS)

Dupart, Yoan; Burel, Laurence; Delichere, Pierre; George, Christian; D'Anna, Barbara

2013-04-01

Volcanic eruptions induce important climatic and weather modifications. When volcanic ashes are emitted into the atmosphere they can travel for several weeks according to their size distribution and altitude of the emission. Eyjafjallajökull eruption, between April 14th and May 23th, is considered as a medium-size eruption. The upper level winds advected ashes over the UK and continental Europe. During volcanic eruptions high amounts of SO2 were injected into the atmosphere (from 50 to 200 ppbv)[1]. Previous works showed that SO2 could be convert into sulfate on mineral dust surfaces under dark conditions[2]. However, no conversion has been studied with real volcanic ashes and under day conditions (light exposure). For this study, real Eyjafjallajökull's ashes samples, collected on the 2010.04.18 at Seljavellir, were used. The ashes were deposited on a horizontal cylindrical coated-wall flow tube reactor surrounded by 5 fluorescent lamps (340-420 nm). The kinetic studies revealed that the presence of UV-A irradiation enhanced the conversion of SO2 on ashes samples. Moreover chemical analyses as XPS, Ion Chromatography and SEM were performed on volcanic ashes before and after exposition to SO2. XPS and ion chromatography analyzes showed that the presence of light increase the SO2 uptake on ashes surfaces and convert it into ions sulphate. Beside SEM analyses disclosed that the conversion takes place systematically on an iron oxide site . By combining kinetics and chemical analysis we are able to propose a new mechanism for the SO2 conversion on mineral surfaces under light conditions. 1. Self, S., et al., Volatile fluxes during flood basalt eruptions and potential effects on the global environment: A Deccan perspective. Earth and Planetary Science Letters, 2006. 248(1-2): p. 518-532. 2. Zhang et al., Heterogeneous Reactions of Sulfur Dioxide on Typical Mineral Particles, J. Phys. Chem. B, 2006

Capture of SO3 isomers in the oxidation of sulfur monoxide with molecular oxygen.

PubMed

Wu, Zhuang; Lu, Bo; Feng, Ruijuan; Xu, Jian; Lu, Yan; Wan, Huabin; Eckhardt, André K; Schreiner, Peter R; Xie, Changjian; Guo, Hua; Zeng, Xiaoqing

2018-02-13

When mixing SO with O 2 in N 2 , Ne, or Ar, an end-on complex OS-OO forms in the gas phase and can subsequently be trapped at cryogenic temperatures (2.8-15.0 K). Upon infrared light irradiation, OS-OO converts to SO 3 and SO 2 + O with the concomitant formation of a rare 1,2,3-dioxathiirane 2-oxide, i.e., cyclic OS([double bond, length as m-dash]O)O. Unexpectedly, the ring-closure of 16 OS- 18 O 18 O yields a ca. 2 : 1 mixture of cyclic 18 OS([double bond, length as m-dash] 16 O) 18 O and 16 OS([double bond, length as m-dash] 18 O) 18 O. The characterization of OS-OO and OS([double bond, length as m-dash]O)O with IR and UV/Vis spectroscopy is supported by high-level ab initio computations.

Biospheric effects of a large extraterrestrial impact: Case study of the cretaceous/tertiary boundary crater

NASA Technical Reports Server (NTRS)

Pope, Kevin O.

1995-01-01

The Chicxulub impact crater, buried in the Yucatan carbonate platform in Mexico, is the site of the impact purported to have caused mass extinctions at the Cretaceous/Tertiary (K/T) boundary. A recently discovered Chicxulub ejecta deposit in Belize contains evidence of carbonate vaporization and precipitation from the vapor plume. Sulfate clasts are almost absent in the Belize ejecta, but are abundant in the coarse ejecta near the crater rim, hwich may reflect the greater abundance of sulfates deep in the target section. The absence of sulfate precipitates in Belize may indicate that most of the vaporized sulfur was deposited in the upper atmosphere. Hydrocode modeling of the impact indicates that between 0.4 to 7.0 x 10(exp 17) g of sulfur were vaporized by the impact in sulfates. Laser experiments indicate that SO2, SO3, and SO4 are produced, and that complex chemical reactions between plume constituents occur during condensation. The sulfur released as SO3 or SO4 converted rapidly into H2HO4 aerosol. A radiative transfer model coupled with a model of coagulation predicts that the aerosol prolonged the initial blackout period caused by impact dust only if it contained impurities. The sulfur released as SO2 converted to aerosol slowly due to the rate limiting oxidation of SO2. Radiative transfer calculations combined with rates of acid production, coagulation, and diffusion indicate that solar transmission was reduced to 10-20 percent of normal for a period of 8-13 years. This reduction produced a climate forcing (cooling) of -300 Wm(exp -2), which far exceeded the +8 Wm(exp -2) greenhouse warming caused by the CO2 released through the vaporization of carbonates, and therefore produced a decade of freezing and near-freezing temperatures. Several decades of moderate warming followed the decade of severe cooling due to the long residence time of CO2. The prolonged impact winter may have been a major cause of the K/T extinctions.

[Desulphurization with multi-needle-water film electrodes by corona discharge].

PubMed

Huang, Xu-ran; Li, Guo-feng; Li, Jie; Wu, Yan

2008-09-01

The study of this paper adopted stainless steel multi-needle as a high voltage electrode system, and water film as low voltage electrode. The electrodes were supplied with negative DC high voltage. Polluted gas containing sulfur dioxide (SO2) flowed into the corona discharge field from the center of the high voltage electrode system in an axis direction, then get across the water surface. Under the effect of corona discharge plasma and water absorption, SO2 was removed by converting it into sulfuric acid. The effect of the three factors which were the applied voltage, SO2 inlet concentration and duration of the exposure to the corona discharge on desulphurization efficiency has been studied mostly. Moreover, the concentrations of SO3(2-) and SO4(2-) ions in the water were measured and the mechanism of desulphurization was analyzed. The results showed that there was a synergistic effect on the removal of SO2 when combining corona discharge and water absorption, and both the desulphurization efficiency and the amount of sulfuric acid increased evidently. As the applied voltage and the duration increased, the desulphurization efficiency increased. Also, the SO2 inlet concentration had effect on desulphurization efficiency. When the SO2 inlet concentration was 430 x 10(-6), the voltage was 14.5 kV and the duration was 7.5 s, a desulphurization efficiency of more than 90% could be attained.

Simultaneous absorption of NO and SO2 into hexamminecobalt(II)/iodide solution.

PubMed

Long, Xiang-Li; Xiao, Wen-De; Yuan, Wei-kang

2005-05-01

An innovative catalyst system has been developed to simultaneously remove NO and SO2 from combustion flue gas. Such catalyst system may be introduced to the scrubbing solution using ammonia solution to accomplish sequential absorption and catalytic oxidation of both NO and SO2 in the same reactor. When the catalyst system is utilized for removing NO and SO2 from the flue gas, Co(NH3)(6)2+ ions act as the catalyst and I- as the co-catalyst. Dissolved oxygen, in equilibrium with the residual oxygen in the flue gas, is the oxidant. The overall removal process is further enhanced by UV irradiation at 365 nm. More than 95% of NO is removed at a feed concentration of 250-900 ppm, and nearly 100% of SO2 is removed at a feed concentration of 800-2500 ppm. The sulfur dioxide co-existing in the flue gas is beneficial to NO absorption into hexamminecobalt(II)/iodide solution. NO and SO2 can be converted to ammonium sulfate and ammonium nitrate that can be used as fertilizer materials. The process described here demonstrates the feasibility of removing SO2 and NO simultaneously only by retrofitting the existing wet ammonia flue-gas-desulfurization (FGD) scrubbers.

Reactions occurring during the sulfation of sodium chloride deposited on alumina substrates

NASA Technical Reports Server (NTRS)

Wu, C. S.; Birks, N.

1986-01-01

The reaction between solid NaCl and air containing 1 pct SO2 has been studied between 500 and 700 C. The reaction product, Na2SO4, forms not only on the surface of the NaCl but also on surrounding areas of the substrate due to the volatility of the NaCl at these temperatures. At the higher temperatures, the vapor pressure of NaCl is so high that the majority of the reaction product is distributed on the substrate. Above 625 C, the reaction product is a liquid solution of NaCl and Na2SO4 that exists only so long as NaCl is supplied from the original crystal source. Eventually, the liquid solidifies by constitutional solidification as the NaCl is converted to Na2SO4. While it exists, the liquid NaCl-Na2SO4 solution is shown to be highly corrosive to Al2O3 and, on a scale of Al2O3 growing on alloy HOS 875, particularly attacks the grain boundaries of the scale at preferred sites where chromium and iron oxides and sulfides rapidly develop. This is proposed as one mechanism by which NaCl deposition contributes to the initiation of low temperature hot corrosion.

Detection of SO towards the transitional disk AB Auriga: the sulfur chemistry in a proto-solar nebula

NASA Astrophysics Data System (ADS)

Fuente, A.; Agúndez, M.; Cernicharo, J.; Goicoechea, J. R.; Bachiller, R.

2017-03-01

The transitional disk around the Herbig Ae star, AB Auriga, has been imaged in the dust continuum emission at 1mm and in the line using the NOEMA interferometer (IRAM) (beam 1.5”). This is the first image of SO ever in a protoplanetary disk (PPD). Simultaneously, we obtained images of the ^{13}CO 2→1, C^{18}O 2→1 and H_{2}CO 3_{0,3} → 2_{0,2} lines. The dust continuum and C^{18}O emissions present the horseshoe morphology that is characteristic of the existence of a dust trap, proving that this disk is at the stage of forming planets. In contrast, SO presents uniform emission all over the disk. We interpret that the uniform SO emission is the consequence of the SO molecules being rapidly converted to SO_{2} and frozen onto the grain mantles at the high densities close to the disk midplane (> 10^{7} cm^{-3}). SO is the second S-bearing molecule detected in a PPD (the first was CS) and opens the possibility to study the sulphur chemistry in a proto-solar nebula analog. Sulfur is widespread in the Solar System and the comprehension of the sulfur chemistry is of paramount importance to understand the formation of our planetary system.

Solar energy converter using surface plasma waves

NASA Technical Reports Server (NTRS)

Anderson, L. M. (Inventor)

1984-01-01

Sunlight is dispersed over a diffraction grating formed on the surface of a conducting film on a substrate. The angular dispersion controls the effective grating period so that a matching spectrum of surface plasmons is excited for parallel processing on the conducting film. The resulting surface plasmons carry energy to an array of inelastic tunnel diodes. This solar energy converter does not require different materials for each frequency band, and sunlight is directly converted to electricity in an efficient manner by extracting more energy from the more energetic photons.

Modular high voltage power supply for chemical analysis

DOEpatents

Stamps, James F [Livermore, CA; Yee, Daniel D [Dublin, CA

2007-01-09

A high voltage power supply for use in a system such as a microfluidics system, uses a DC--DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC--DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

Modular high voltage power supply for chemical analysis

DOEpatents

Stamps, James F [Livermore, CA; Yee, Daniel D [Dublin, CA

2010-05-04

A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

Modular high voltage power supply for chemical analysis

DOEpatents

Stamps, James F [Livermore, CA; Yee, Daniel D [Dublin, CA

2008-07-15

A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

Production of butanol by fermentation in the presence of cocultures of clostridium

NASA Technical Reports Server (NTRS)

Bergstrom, S. L.; Foutch, G. L. (Inventor)

1985-01-01

Sugars are converted to a mixture of solvents including butanol by a fermentation process employing a coculture of microorganisms of the Clostridium genus, one of said microorganisms favoring the production of butyric acid and the other of which converts the butyric acid so produced to butanol. The use of a coculture substantially increases the yield of butanol over that obtained using a culture employing only one microorganism.

The role of NaCl in flame chemistry, in the deposition process, and in its reactions with protective oxides as related to hot corrosion

NASA Technical Reports Server (NTRS)

Kohl, F. J.; Stearns, C. A.

1979-01-01

Sodium chloride is believed to be the primary source of turbine engine contamination that contributes to hot corrosion. The behavior of NaCl-containing aerosols ingested with turbine intake air is very complex; some of the NaCl may vaporize during combustion while some may remain as particulates. The NaCl can lead to Na2SO4 formation by several possible routes or it can contribute to corrosion directly. Hydrogen or oxygen atom reaction with NaCl(c) was shown to result in the release of Na(g). Gaseous NaCl in flames can be partially converted to gaseous Na2SO4 by homogeneous reactions. The remaining gaseous NaCl and other Na-containing molecules can act as sodium carriers for condensate deposition of Na2SO4 on cool surfaces. A frozen boundary layer theory was developed to predict the rates of deposition. The condensed phase NaCl can be converted directly to condensed Na2SO4 by reaction with sulfur oxides and O2. Reaction of gaseous NaCl with Cr2O3 results in the vapor phase transport of chromium by the formation of complex Cr-containing gaseous molecules. Similar gaseous complexes are formed with molybdenum. The presence of gaseous NaCl was shown to affect the oxidation kinetics of Ni-Cr alloys. It also causes changes in the surface morphology of Al2O3 scales formed on Al-containing alloys.

Research on Parallel Three Phase PWM Converters base on RTDS

NASA Astrophysics Data System (ADS)

Xia, Yan; Zou, Jianxiao; Li, Kai; Liu, Jingbo; Tian, Jun

2018-01-01

Converters parallel operation can increase capacity of the system, but it may lead to potential zero-sequence circulating current, so the control of circulating current was an important goal in the design of parallel inverters. In this paper, the Real Time Digital Simulator (RTDS) is used to model the converters parallel system in real time and study the circulating current restraining. The equivalent model of two parallel converters and zero-sequence circulating current(ZSCC) were established and analyzed, then a strategy using variable zero vector control was proposed to suppress the circulating current. For two parallel modular converters, hardware-in-the-loop(HIL) study based on RTDS and practical experiment were implemented, results prove that the proposed control strategy is feasible and effective.

Systems for controlling the intensity variations in a laser beam and for frequency conversion thereof

DOEpatents

Skupsky, S.; Craxton, R.S.; Soures, J.

1990-10-02

In order to control the intensity of a laser beam so that its intensity varies uniformly and provides uniform illumination of a target, such as a laser fusion target, a broad bandwidth laser pulse is spectrally dispersed spatially so that the frequency components thereof are spread apart. A disperser (grating) provides an output beam which varies spatially in wavelength in at least one direction transverse to the direction of propagation of the beam. Temporal spread (time delay) across the beam is corrected by using a phase delay device (a time delay compensation echelon). The dispersed beam may be amplified with laser amplifiers and frequency converted (doubled, tripled or quadrupled in frequency) with nonlinear optical elements (birefringent crystals). The spectral variation across the beam is compensated by varying the angle of incidence on one of the crystals with respect to the crystal optical axis utilizing a lens which diverges the beam. Another lens after the frequency converter may be used to recollimate the beam. The frequency converted beam is recombined so that portions of different frequency interfere and, unlike interference between waves of the same wavelength, there results an intensity pattern with rapid temporal oscillations which average out rapidly in time thereby producing uniform illumination on target. A distributed phase plate (also known as a random phase mask), through which the spectrally dispersed beam is passed and then focused on a target, is used to provide the interference pattern which becomes nearly modulation free and uniform in intensity in the direction of the spectral variation. 16 figs.

Systems for controlling the intensity variations in a laser beam and for frequency conversion thereof

DOEpatents

Skupsky, Stanley; Craxton, R. Stephen; Soures, John

1990-01-01

In order to control the intensity of a laser beam so that its intensity varies uniformly and provides uniform illumination of a target, such as a laser fusion target, a broad bandwidth laser pulse is spectrally dispersed spatially so that the frequency components thereof are spread apart. A disperser (grating) provides an output beam which varies spatially in wavelength in at least one direction transverse to the direction of propagation of the beam. Temporal spread (time delay) across the beam is corrected by using a phase delay device (a time delay compensation echelon). The dispersed beam may be amplified with laser amplifiers and frequency converted (doubled, tripled or quadrupled in frequency) with nonlinear optical elements (birefringent crystals). The spectral variation across the beam is compensated by varying the angle of incidence on one of the crystals with respect to the crystal optical axis utilizing a lens which diverges the beam. Another lens after the frequency converter may be used to recollimate the beam. The frequency converted beam is recombined so that portions of different frequency interfere and, unlike interference between waves of the same wavelength, there results an intensity pattern with rapid temoral oscillations which average out rapidly in time thereby producing uniform illumination on target. A distributed phase plate (also known as a random phase mask), through which the spectrally dispersed beam is passed and then focused on a target, is used to provide the interference pattern which becomes nearly modulation free and uniform in intensity in the direction of the spectral variation.

Catalytic converter with fluid injector for catalyst-free enclosure of catalyst bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrew, S.P.S.

1984-09-25

A fluid injection lozenge comprises two tubes supporting a perforate member forming a cage enclosing the space between the tubes. Each tube has a series of perforations along its length so that a fluid can be injected, through the tube, into the enclosed space. The lozenges are of use in catalytic converters of either the axial or radial flow design. In the case of a radial flow converter, a plurality of tubes are provided, preferably connected in pairs by the perforate members, to form a squirrel cage structure, disposed in the catalyst bed.

Single phase bi-directional AC-DC converter with reduced passive components size and common mode electro-magnetic interference

DOEpatents

Mi, Chris; Li, Siqi

2017-01-31

A bidirectional AC-DC converter is presented with reduced passive component size and common mode electro-magnetic interference. The converter includes an improved input stage formed by two coupled differential inductors, two coupled common and differential inductors, one differential capacitor and two common mode capacitors. With this input structure, the volume, weight and cost of the input stage can be reduced greatly. Additionally, the input current ripple and common mode electro-magnetic interference can be greatly attenuated, so lower switching frequency can be adopted to achieve higher efficiency.

Liquefaction process

DOEpatents

Poddar, Syamal K.

1981-01-01

Scale formation during the liquefaction of lower ranking coals and similar carbonaceous materials is significantly reduced and/or prevented by pretreatment with a combination of pretreating agents comprising SO.sub.2 and an oxidizing agent. It is essential to effective operation that the moisture content of the solid carbonaceous material be within the range from about 10 to about 25 wt %, based on dry solid carbonaceous material, during the pretreatment. The pretreatment is believed to convert at least a portion of the scale-forming components and particularly calcium, to the corresponding sulfate prior to liquefaction. The pretreatment may be accomplished with the combination of pretreating agents either simultaneously by using a mixture comprising SO.sub.2 and a gaseous oxidizing agent or sequentially by first treating with SO.sub.2 and then with an oxidizing agent.

The dynamics of health care opinion, 2008-2010: partisanship, self-interest, and racial resentment.

PubMed

Henderson, Michael; Hillygus, D Sunshine

2011-12-01

Recent debate over the Patient Protection and Affordable Care Act highlights the extent of party polarization in Washington. While the partisan divide on this issue is stark among political elites, it is less clear how the mass electorate has responded to this divisive conflict. In this article we examine individual-level dynamics in health care attitudes between 2008 and 2010. We find partisan attachments and self-interests strongly predict change in health care attitudes, with Republicans growing more opposed to universal health insurance between 2008 and 2010, and those personally worried about medical expenses less likely to abandon support. We find, however, that the effect of partisanship is moderated by self-interest, with strong Republicans significantly less likely to switch to opposition if they were personally worried about medical expenses. Finally, we find that health care policy preferences, already tinged with racial attitudes in 2008, became increasingly so by 2010.

Disentangling the Importance of Psychological Predispositions and Social Constructions in the Organization of American Political Ideology.

PubMed

Verhulst, Brad; Hatemi, Peter K; Eaves, Lindon J

2012-06-01

Ideological preferences within the American electorate are contingent on both the environmental conditions that provide the content of the contemporary political debate and internal predispositions that motivate people to hold liberal or conservative policy preferences. In this article we apply Jost, Federico, and Napier's (2009) top-down/bottom-up theory of political attitude formation to a genetically informative population sample. In doing so, we further develop the theory by operationalizing the top-down pathway to be a function of the social environment and the bottom-up pathway as a latent set of genetic factors. By merging insights from psychology, behavioral genetics, and political science, we find strong support for the top-down/bottom-up framework that segregates the two independent pathways in the formation of political attitudes and identifies a different pattern of relationships between political attitudes at each level of analysis.

A Social Diffusion Model with an Application on Election Simulation

PubMed Central

Wang, Fu-Min; Hung, San-Chuan; Kung, Perng-Hwa; Lin, Shou-De

2014-01-01

Issues about opinion diffusion have been studied for decades. It has so far no empirical approach to model the interflow and formation of crowd's opinion in elections due to two reasons. First, unlike the spread of information or flu, individuals have their intrinsic attitudes to election candidates in advance. Second, opinions are generally simply assumed as single values in most diffusion models. However, in this case, an opinion should represent preference toward multiple candidates. Previously done models thus may not intuitively interpret such scenario. This work is to design a diffusion model which is capable of managing the aforementioned scenario. To demonstrate the usefulness of our model, we simulate the diffusion on the network built based on a publicly available bibliography dataset. We compare the proposed model with other well-known models such as independent cascade. It turns out that our model consistently outperforms other models. We additionally investigate electoral issues with our model simulator. PMID:24995351

Absolute sulfur isotope amount ratios in two batches of high purity SO2 gas: sulfur isotope reference materials IRMM-2012 and IRMM-2013

NASA Astrophysics Data System (ADS)

Valkiers, S.; Ding, T.; Ruße, K.; de Bièvre, P.; Taylor, P. D. P.

2005-04-01

SI-traceable ("absolute") values have been obtained for sulfur isotope amount ratios n(33S)/n(32S) and n(34S)/n(32S), in two batches of high purity SO2 gas (IRMM-2012 and IRMM-2013). The SO2 gas was converted at IMR-Beijing to Ag2S, then fluorinated to SF6 gas both at IMR-Beijing and at IRMM-Geel. Yields of different conversion methods exceeded 99%. The sulfur amount-of-substance measurements were performed by gas mass spectrometry on SF5+ ions using "IRMM's amount comparator II". These isotope amount ratios were calibrated by means of gravimetrically prepared synthetic mixtures of highly enriched sulfur isotopes (32S, 33S and 34S) in Ag2S form. The ratio values in the SO2 Secondary Measurement Standard are traceable to the SI system. They can be used in the calibration of field sulfur isotope measurements thus making these metrologically traceable to the SI.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erga, O.; Finborud, A.

Cost-effective FGD processes with high SO{sub 2} removal efficiencies are required for fossil-fired power plants. With high-sulfur fuel, conventional limestone processes are less ideal, and regenerative processes with SO{sub 2} recovery may offer important advantages. The Elsorb process, which is being developed by the Norwegian company Elkem Technology a.s., is a regenerable SO{sub 2} recovery process which operates on the principle of chemical absorption followed by regeneration by evaporation. The process is based on the use of a chemical stable sodium phosphate buffer in high concentration. It combines high cleaning efficiency with high cyclic absorption capacity, moderate energy requirement, andmore » very little oxidation losses. The process produces SO{sub 2} (g) which can be converted into liquid SO{sub 2}, sulfuric acid or elemental sulfur. The Elsorb process has been pilot tested on flue gas from a coal-fired boiler with very promising results, concerning cleaning efficiency and oxidation losses of SO{sub 2}. The first commercial Elsorb plant has been installed for treating incinerated Claus tail gas. Preliminary data regarding cleaning efficiency are in accordance with the pilot tests. However, unexpected high consumption of make-up chemicals were encountered. The existing incinerator is now to be modified. Complete data for the Elsorb plant should be available later this year. 1 fig.« less

Thermal Reactions of H2O2 on Icy Satellites and Small Bodies: Descent with Modification?

NASA Technical Reports Server (NTRS)

Hudson, Reggie L.; Loeffler, Mark J.

2012-01-01

Magnetospheric radiation drives surface and near-surface chemistry on Europa, but below a few meters Europa's chemistry is hidden from direct observation . As an example, surface radiation chemistry converts H2O and SO2 into H2O2 and (SO4)(sup 2-), respectively, and these species will be transported downward for possible thermally-driven reactions. However, while the infrared spectra and radiation chemistry of H2O2-containing ices are well documented, this molecule's thermally-induced solid-phase chemistry has seldom been studied. Here we report new results on thermal reactions in H2O + H2O2 + SO2 ices at 50 - 130 K. As an example of our results, we find that warming H2O + H2O2 + SO2 ices promotes SO2 oxidation to (SO4)(sup 2-). These results have implications for the survival of H2O2 as it descends, with modification, towards a subsurface ocean on Europa. We suspect that such redox chemistry may explain some of the observations related to the presence and distribution of H2O2 across Europa's surface as well as the lack of H2O2 on Ganymede and Callisto.

The negative and positive electrorheological behavior and vibration damping characteristics of colemanite and polyindene/colemanite conducting composite

NASA Astrophysics Data System (ADS)

Cetin, B.; Unal, H. I.; Erol, O.

2012-12-01

In this study, the electrorheological (ER) properties of colemanite and polyindene (94.8% PIn)/colemanite (5.2%) conducting composite were investigated by dispersion in silicone oil (SO). The zeta (ζ)-potentials and antisedimentation ratios of the materials were determined. Some parameters which affect the ER properties of all the dispersions such as the volume fraction, electric field strength (E), shear rate, frequency and temperature were investigated. The rather unusual behavior known as the negative ER effect was observed for colemanite/SO above E = 1.5 kV mm-1 and for PIn/colemanite/SO under all values of the electric field strength even at high volume fraction. This negative ER response was converted to a positive one by the addition of non-ionic surfactant. Furthermore, glycerol was used as a polar promoter and observed to enhance the ER activity of the colemanite/SO system. Creep-recovery tests were applied to all the dispersions studied to investigate their behavior under sustained shear stress. Finally, 28% and 30% vibration damping capacities were achieved using an automobile shock absorber for the glycerol/colemanite/SO and non-ionic surfactant/PIn/colemanite/SO systems under the E = 0.17 kV mm-1 condition, respectively.

SO2 Initiates the Efficient Conversion of NO2 to HONO on MgO Surface.

PubMed

Ma, Qingxin; Wang, Tao; Liu, Chang; He, Hong; Wang, Zhe; Wang, Weihao; Liang, Yutong

2017-04-04

Nitrous acid (HONO) is an important source of hydroxyl radical (OH) that determines the fate of many chemically active and climate relevant trace gases. However, the sources and the formation mechanisms of HONO remain poorly understood. In this study, the effect of SO 2 on the heterogeneous reactions of NO 2 on MgO as a mineral dust surrogate was investigated. The reactivity of MgO to NO 2 is weak, while coexisting SO 2 can increase the uptake coefficients of NO 2 on MgO by 2-3 orders of magnitude. The uptake coefficients of NO 2 on SO 2 -aged MgO are independent of NO 2 concentrations in the range of 20-160 ppbv and relative humidity (0-70%RH). The reaction mechanism was demonstrated to be a redox reaction between NO 2 and surface sulfite. In the presence of SO 2 , NO 2 was reduced to nitrite under dry conditions, which could be further converted to gas-phase HONO in humid conditions. These results suggest that the reductive effect of SO 2 on the heterogeneous conversion of NO 2 to HONO may have a significant contribution to the unknown sources of HONO observed in polluted areas (for example, in China).

Effect of Sulfate on Selenium Uptake And Chemical Speciation in Convolvulus Arvensis L

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cruz-Jimenez, G.; Peralta-Video, J.R.; Rosa, G.de la

2007-08-08

Hydroponic experiments were performed to study several aspects of Se uptake by C. arvensis plants. Ten day old seedlings were exposed for eight days to different combinations of selenate (SeO{sub 4}{sup 2-}), sulfate (SO{sub 4}{sup 2-}), and selenite (SeO{sub 3}{sup 2-}). The results showed that in C. arvensis, SO{sub 4}{sup 2-} had a negative effect (P < 0.05) on SeO{sub 4}{sup 2-} uptake. However, a positive interaction produced a significant increase in SO{sub 4}{sup 2-} uptake when SeO{sub 4}{sup 2-} was at high concentration in the media. X-ray absorption spectroscopy studies showed that C. arvensis plants converted more than 70%more » of the supplied SeO{sub 3}{sup 2-} into organoselenium compounds. However, only approximately 50% of the supplied SeO{sub 4}{sup 2-} was converted into organoselenium species while the residual 50% remained in the inorganic form. Analysis using LC-XANES fittings confirmed that the S metabolic pathway was affected by the presence of Se. The main Se compounds that resembled those Se species identified in C. arvensis were Se-cystine, Se-cysteine, SeO{sub 3}{sup 2-}, and SeO{sub 4}{sup 2-}, whereas for S the main compounds were cysteine, cystine, oxidized glutathione, reduced glutathione, and SO{sub 4}{sup 2-}. The results of these studies indicated that C. arvensis could be considered as a possible option for the restoration of soil moderately contaminated with selenium even in the presence of sulfate.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sublette, K.L.

With the continual increase in the utilization of high sulfur and high nitrogen containing fossil fuels, the release of airborne pollutants into the environment has become a critical problem. The fuel sulfur is converted to SO{sub 2} during combustion. Fuel nitrogen and a fraction of the nitrogen from the combustion air are converted to nitric oxide and nitrogen dioxide, NO{sub x}. For the past five years Combustion Engineering (now Asea Brown Boveri or ABB) and, since 1986, the University of Tulsa (TU) have been investigating the oxidation of H{sub 2}S by the facultatively anaerobic and autotrophic bacterium Thiobacillus denitrificans andmore » have developed a process, concept for the microbial removal of H{sub 2}S from a gas stream the simultaneous removal of SO{sub 2} and NO by D. desulfuricans and T. denitrificans co-cultures and cultures-in-series was demonstrated. These systems could not be sustained due to NO inhibition of D. desulfuricans. However, a preliminary economic analysis has shown that microbial reduction of SO{sub 2} to H{sub 2}S with subsequent conversion to elemental sulfur by the Claus process is both technically and economically feasible if a less expensive carbon and/or energy source can be found. It has also been demonstrated that T. denitrificans can be grown anaerobically on NO(g) as a terminal electron acceptor with reduction to elemental nitrogen. Microbial reduction of NO{sub x} is a viable process concept for the disposal of concentrated streams of NO{sub x} as may be produced by certain regenerable processes for the removal of SO{sub 2} and NO{sub x} from flue gas.« less

From Deficit to Disenfranchisement: Reframing Youth Electoral Participation

ERIC Educational Resources Information Center

Edwards, Kathy

2007-01-01

Low youth electoral turnouts are considered problematic in many democracies. Here I explore youth electoral engagement in the Australian context where the policy literature attributes low youth electoral enrolments to apathetic and disassociated youth, and the response is Civics and Citizenship education. This construction of youth and advocacy of…

Representation and the Rules of the Game: An Electoral Simulation

ERIC Educational Resources Information Center

Hoffman, Donna R.

2009-01-01

It is often a difficult proposition for introductory American government students to comprehend different electoral systems and how the rules of the game affect the representation that results. I have developed a simulation in which different proportional-based electoral systems are compared with a single-member plurality electoral system. In…

The costs of electoral fraud: establishing the link between electoral integrity, winning an election, and satisfaction with democracy

PubMed Central

Fortin-Rittberger, Jessica; Harfst, Philipp; Dingler, Sarah C.

2017-01-01

ABSTRACT Previous research has shown that voters’ perception of electoral fairness has an impact on their attitudes and behaviors. However, less research has attempted to link objective measurements of electoral integrity on voters’ attitudes about the democratic process. Drawing on data from the Comparative Study of Electoral Systems and the Quality of Elections Data, we investigate whether cross-national differences in electoral integrity have significant influences on citizens’ level of satisfaction with democracy. We hypothesize that higher levels of observed electoral fraud will have a negative impact on evaluations of the democratic process, and that this effect will be mediated by a respondent’s status as a winner or loser of an election. The article’s main finding is that high levels of electoral fraud are indeed linked to less satisfaction with democracy. However, we show that winning only matters in elections that are conducted in an impartial way. The moment elections start to display the telltale signs of manipulation and malpractice, winning and losing no longer have different effects on voter’s levels of satisfaction with democracy. PMID:28824703

The costs of electoral fraud: establishing the link between electoral integrity, winning an election, and satisfaction with democracy.

PubMed

Fortin-Rittberger, Jessica; Harfst, Philipp; Dingler, Sarah C

2017-07-03

Previous research has shown that voters' perception of electoral fairness has an impact on their attitudes and behaviors. However, less research has attempted to link objective measurements of electoral integrity on voters' attitudes about the democratic process. Drawing on data from the Comparative Study of Electoral Systems and the Quality of Elections Data, we investigate whether cross-national differences in electoral integrity have significant influences on citizens' level of satisfaction with democracy. We hypothesize that higher levels of observed electoral fraud will have a negative impact on evaluations of the democratic process, and that this effect will be mediated by a respondent's status as a winner or loser of an election. The article's main finding is that high levels of electoral fraud are indeed linked to less satisfaction with democracy. However, we show that winning only matters in elections that are conducted in an impartial way. The moment elections start to display the telltale signs of manipulation and malpractice, winning and losing no longer have different effects on voter's levels of satisfaction with democracy.

Validation Studies of the Accuracy of Various SO2 Gas Retrievals in the Thermal InfraRed (8-14 μm)

NASA Astrophysics Data System (ADS)

Gabrieli, A.; Wright, R.; Lucey, P. G.; Porter, J. N.; Honniball, C.; Garbeil, H.; Wood, M.

2016-12-01

Quantifying hazardous SO2 in the atmosphere and in volcanic plumes is important for public health and volcanic eruption prediction. Remote sensing measurements of spectral radiance of plumes contain information on the abundance of SO2. However, in order to convert such measurements into SO2 path-concentrations, reliable inversion algorithms are needed. Various techniques can be employed to derive SO2 path-concentrations. The first approach employs a Partial Least Square Regression model trained using MODTRAN5 simulations for a variety of plume and atmospheric conditions. Radiances at many spectral wavelengths (8-14 μm) were used in the algorithm. The second algorithm uses measurements inside and outside the SO2 plume. Measurements in the plume-free region (background sky) make it possible to remove background atmospheric conditions and any instrumental effects. After atmospheric and instrumental effects are removed, MODTRAN5 is used to fit the SO2 spectral feature and obtain SO2 path-concentrations. The two inversion algorithms described above can be compared with the inversion algorithm for SO2 retrievals developed by Prata and Bernardo (2014). Their approach employs three wavelengths to characterize the plume temperature, the atmospheric background, and the SO2 path-concentration. The accuracy of these various techniques requires further investigation in terms of the effects of different atmospheric background conditions. Validating these inversion algorithms is challenging because ground truth measurements are very difficult. However, if the three separate inversion algorithms provide similar SO2 path-concentrations for actual measurements with various background conditions, then this increases confidence in the results. Measurements of sky radiance when looking through SO2 filled gas cells were collected with a Thermal Hyperspectral Imager (THI) under various atmospheric background conditions. These data were processed using the three inversion approaches, which were tested for convergence on the known SO2 gas cell path-concentrations. For this study, the inversion algorithms were modified to account for the gas cell configuration. Results from these studies will be presented, as well as results from SO2 gas plume measurements at Kīlauea volcano, Hawai'i.

A new process for converting SO2 to sulfur without generating secondary pollutants through reactions involving CaS and CaSO4.

PubMed

Sohn, H Y; Kim, Byung-Su

2002-07-01

Nonferrous smelters and coal gasification processes generate environmentally harmful sulfur dioxide streams, most of which are treated to produce sulfuric acid with the accompanying problems of market shortage and transportation difficulties. Some sulfur dioxide streams are scrubbed with an alkali solution or a solid substance such as limestone or dolomite, which in turn generates wastes that pose other pollution problems. While the conversion of sulfur dioxide to elemental sulfur has many environmental advantages, no processes exist that are environmentally acceptable and economically viable. A new method for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium sulfide and calcium sulfate without generating solid wastes has been developed. In this process, calcium sulfate pellets as the starting raw material are reduced by a suitable reducing agent such as hydrogen to produce calcium sulfide pellets, which are used to reduce sulfur dioxide producing elemental sulfur vapor and calcium sulfate. The latter is then reduced to regenerate calcium sulfide. Thermodynamic analysis and experimental results indicated that the CaS-SO2 reaction produces mainly sulfur vapor and solid calcium sulfate and that the gaseous product from the CaSO4-H2 reaction is mainly water vapor. The rates of the two reactions are reasonably rapid in the temperature range 1000-1100 K, and, importantly, the physical strengths and reactivities of the pellets are maintained largely unchanged up to the tenth cycle, the last cycle tested in this work. Sulfur dioxide-containing streams from certain sources, such as the regenerator off-gas from an integrated gasification combined cycle desulfurization unit and new sulfide smelting plants, contain much higher partial pressures of SO2. In these cases, the rate of the first reaction is expected to be proportionally higher than in the test conditions reported in this paper.

Modern Day Re-analysis of Pinatubo SO2 Injection, Cloud dispersion and Stratospheric Aerosols

NASA Astrophysics Data System (ADS)

Bhartia, P. K.; Krotkov, N. A.; Aquila, V.; Hughes, E. J.; Li, C.; Fisher, B. L.

2016-12-01

Cataclysmic June 15 1991 eruption of Mt. Pinatubo injected largest amount of SO2 in the lower stratosphere during the satellite era. The resulting volcanic clouds were tracked by the NASA's Nimbus 7 TOMS sensor that provided first estimates of total emissions of SO2 gas ( 15+/-3 Mt). Over time SO2 converted to long-lasting sulfate aerosols affecting radiation balance and composition of the stratosphere. Large numbers of articles and papers published in the past 25 years make this the most well-studied volcanic eruption. Still, several unresolved scientific issues remain: SO2 injection height, subsequent lofting of SO2 and aerosols in the stratosphere, how much sulfate aerosols were produced in the eruption (i.e., initial sulfate to SO2 ratio), and impact on stratospheric ozone. To answer these questions we have re-analyzed past satellite measurements using modern day tools, such as re-analyzed wind data from Goddard Modeling and Assimilation Office (GMAO), improved trajectory analysis tools, better radiative transfer model to process backscatter UV data from N7/TOMS and two NOAA SBUV/2s sensors, which provided measurements at shorter UV wavelengths that are sensitive to aerosols and SO2 in the mid stratosphere ( 25 km). We have also re-analyzed aerosol data from SAGE, AVHRR, and several instruments on the UARS satellite. These data provide strong support for recent assessment by modelers that the bulk of SO2 mass injected by the volcano was well below the 25 km altitude, contrary to earlier estimates. We also find convincing evidence that there was significant amount of sulfate aerosols embedded even in the day-old SO2 cloud. These results strongly support the hypothesis that SO2 gas self-lofted to 25 km as seeen by UARS MLS several weeks after the eruption and aerosols to 35 km, as seen by the SAGE sensor several months later.

Proof of Principle for Active Detection of Fissionable Material Using Intense, Pulsed-Bremsstrahlung-Induced Photofission

DTIC Science & Technology

2014-10-07

aligned at 45° so that the two radiation detectors view the DU plate at near normal incidence. Delayed neutrons were measured using a single He-3...bremsstrahlung converter. TLDs and an x-ray pinhole camera are used to measure the angular and radial x-ray dose distributions, 43 , 45 and He-3 detectors are...explanation is supported by x-ray pinhole images which show that the radial distribution of bremsstrahlung from the converter shifts to larger

Biologically Inspired Radiation Reflector

NASA Technical Reports Server (NTRS)

Johnson, Sylvia M. (Inventor); Lawson, John W. (Inventor); Squire, Thomas H. (Inventor); Gusman, Michael (Inventor)

2018-01-01

A thermal protection system (TPS) comprising a mixture of silicon carbide and SiOx that has been converted from Si that is present in a collection of diatom frustules and at least one diatom has quasi-periodic pore-to-pore separation distance d(p-p) in a selected range. Where a heat shield comprising the converted SiC/SiOx frustules receives radiation, associated with atmospheric (re)entry, a portion of this radiation is reflected so that radiation loading of the heat shield is reduced.

Second harmonic generation in resonant optical structures

DOEpatents

Eichenfield, Matt; Moore, Jeremy; Friedmann, Thomas A.; Olsson, Roy H.; Wiwi, Michael; Padilla, Camille; Douglas, James Kenneth; Hattar, Khalid Mikhiel

2018-01-09

An optical second-harmonic generator (or spontaneous parametric down-converter) includes a microresonator formed of a nonlinear optical medium. The microresonator supports at least two modes that can be phase matched at different frequencies so that light can be converted between them: A first resonant mode having substantially radial polarization and a second resonant mode having substantially vertical polarization. The first and second modes have the same radial order. The thickness of the nonlinear medium is less than one-half the pump wavelength within the medium.

Converting Topographic Maps into Digital Form to Aid in Archeological Research in the Peten, Guatemala

NASA Technical Reports Server (NTRS)

Aldrich, Serena R.

1999-01-01

The purpose of my project was to convert a topographical map into digital form so that the data can be manipulated and easily accessed in the field. With the data in this particular format, Dr. Sever and his colleagues can highlight the specific features of the landscape that they require for their research of the ancient Mayan civilization. Digital elevation models (DEMs) can also be created from the digitized contour features adding another dimension to their research.

Sulfur emission from Victorian brown coal under pyrolysis, oxy-fuel combustion and gasification conditions.

PubMed

Chen, Luguang; Bhattacharya, Sankar

2013-02-05

Sulfur emission from a Victorian brown coal was quantitatively determined through controlled experiments in a continuously fed drop-tube furnace under three different atmospheres: pyrolysis, oxy-fuel combustion, and carbon dioxide gasification conditions. The species measured were H(2)S, SO(2), COS, CS(2), and more importantly SO(3). The temperature (873-1273 K) and gas environment effects on the sulfur species emission were investigated. The effect of residence time on the emission of those species was also assessed under oxy-fuel condition. The emission of the sulfur species depended on the reaction environment. H(2)S, SO(2), and CS(2) are the major species during pyrolysis, oxy-fuel, and gasification. Up to 10% of coal sulfur was found to be converted to SO(3) under oxy-fuel combustion, whereas SO(3) was undetectable during pyrolysis and gasification. The trend of the experimental results was qualitatively matched by thermodynamic predictions. The residence time had little effect on the release of those species. The release of sulfur oxides, in particular both SO(2) and SO(3), is considerably high during oxy-fuel combustion even though the sulfur content in Morwell coal is only 0.80%. Therefore, for Morwell coal utilization during oxy-fuel combustion, additional sulfur removal, or polishing systems will be required in order to avoid corrosion in the boiler and in the CO(2) separation units of the CO(2) capture systems.

Phase transformations of α-alumina made from waste aluminum via a precipitation technique.

PubMed

Matori, Khamirul Amin; Wah, Loy Chee; Hashim, Mansor; Ismail, Ismayadi; Zaid, Mohd Hafiz Mohd

2012-12-07

We report on a recycling project in which α-Al(2)O(3) was produced from aluminum cans because no such work has been reported in literature. Heated aluminum cans were mixed with 8.0 M of H(2)SO(4) solution to form an Al(2)(SO(4))(3) solution. The Al(2)(SO(4))(3) salt was contained in a white semi-liquid solution with excess H(2)SO(4); some unreacted aluminum pieces were also present. The solution was filtered and mixed with ethanol in a ratio of 2:3, to form a white solid of Al(2)(SO(4))(3)·18H(2)O. The Al(2)(SO(4))(3)·18H(2)O was calcined in an electrical furnace for 3 h at temperatures of 400-1400 °C. The heating and cooling rates were 10 °C /min. XRD was used to investigate the phase changes at different temperatures and XRF was used to determine the elemental composition in the alumina produced. A series of different alumina compositions, made by repeated dehydration and desulfonation of the Al(2)(SO(4))(3)·18H(2)O, is reported. All transitional alumina phases produced at low temperatures were converted to α-Al(2)O(3) at high temperatures. The X-ray diffraction results indicated that the α-Al(2)O(3) phase was realized when the calcination temperature was at 1200 °C or higher.

Phase Transformations of α-Alumina Made from Waste Aluminum via a Precipitation Technique

PubMed Central

Matori, Khamirul Amin; Wah, Loy Chee; Hashim, Mansor; Ismail, Ismayadi; Zaid, Mohd Hafiz Mohd

2012-01-01

We report on a recycling project in which α-Al2O3 was produced from aluminum cans because no such work has been reported in literature. Heated aluminum cans were mixed with 8.0 M of H2SO4 solution to form an Al2(SO4)3 solution. The Al2(SO4)3 salt was contained in a white semi-liquid solution with excess H2SO4; some unreacted aluminum pieces were also present. The solution was filtered and mixed with ethanol in a ratio of 2:3, to form a white solid of Al2(SO4)3·18H2O. The Al2(SO4)3·18H2O was calcined in an electrical furnace for 3 h at temperatures of 400–1400 °C. The heating and cooling rates were 10 °C/min. XRD was used to investigate the phase changes at different temperatures and XRF was used to determine the elemental composition in the alumina produced. A series of different alumina compositions, made by repeated dehydration and desulfonation of the Al2(SO4)3·18H2O, is reported. All transitional alumina phases produced at low temperatures were converted to α-Al2O3 at high temperatures. The X-ray diffraction results indicated that the α-Al2O3 phase was realized when the calcination temperature was at 1200 °C or higher. PMID:23222685

Noncompetitive and Competitive Adsorption of Heavy Metals in Sulfur-Functionalized Ordered Mesoporous Carbon.

PubMed

Saha, Dipendu; Barakat, Soukaina; Van Bramer, Scott E; Nelson, Karl A; Hensley, Dale K; Chen, Jihua

2016-12-14

In this work, sulfur-functionalized ordered mesoporous carbons were synthesized by activating the soft-templated mesoporous carbons with sulfur bearing salts that simultaneously enhanced the surface area and introduced sulfur functionalities onto the parent carbon surface. XPS analysis showed that sulfur content within the mesoporous carbons were between 8.2% and 12.9%. The sulfur functionalities include C-S, C═S, -COS, and SO x . SEM images confirmed the ordered mesoporosity within the material. The BET surface areas of the sulfur-functionalized ordered mesoporous carbons range from 837 to 2865 m 2 /g with total pore volume of 0.71-2.3 cm 3 /g. The carbon with highest sulfur functionality was examined for aqueous phase adsorption of mercury (as HgCl 2 ), lead (as Pb(NO 3 ) 2 ), cadmium (as CdCl 2 ), and nickel (as NiCl 2 ) ions in both noncompetitive and competitive mode. Under noncompetitive mode and at a pH greater than 7.0 the affinity of sulfur-functionalized carbons toward heavy metals were in the order of Hg > Pb > Cd > Ni. At lower pH, the adsorbent switched its affinity between Pb and Cd. In the noncompetitive mode, Hg and Pb adsorption showed a strong pH dependency whereas Cd and Ni adsorption did not demonstrate a significant influence of pH. The distribution coefficient for noncompetitive adsorption was in the range of 2448-4000 mL/g for Hg, 290-1990 mL/g for Pb, 550-560 mL/g for Cd, and 115-147 for Ni. The kinetics of adsorption suggested a pseudo-second-order model fits better than other models for all the metals. XPS analysis of metal-adsorption carbons suggested that 7-8% of the adsorbed Hg was converted to HgSO 4 , 14% and 2% of Pb was converted to PbSO 4 and PbS/PbO, respectively, and 5% Cd was converted to CdSO 4 . Ni was below the detection limit for XPS. Overall results suggested these carbon materials might be useful for the separation of heavy metals.

Quality models for audiovisual streaming

NASA Astrophysics Data System (ADS)

Thang, Truong Cong; Kim, Young Suk; Kim, Cheon Seog; Ro, Yong Man

2006-01-01

Quality is an essential factor in multimedia communication, especially in compression and adaptation. Quality metrics can be divided into three categories: within-modality quality, cross-modality quality, and multi-modality quality. Most research has so far focused on within-modality quality. Moreover, quality is normally just considered from the perceptual perspective. In practice, content may be drastically adapted, even converted to another modality. In this case, we should consider the quality from semantic perspective as well. In this work, we investigate the multi-modality quality from the semantic perspective. To model the semantic quality, we apply the concept of "conceptual graph", which consists of semantic nodes and relations between the nodes. As an typical of multi-modality example, we focus on audiovisual streaming service. Specifically, we evaluate the amount of information conveyed by a audiovisual content where both video and audio channels may be strongly degraded, even audio are converted to text. In the experiments, we also consider the perceptual quality model of audiovisual content, so as to see the difference with semantic quality model.

Electoral Susceptibility and Entropically Driven Interactions

NASA Astrophysics Data System (ADS)

Caravan, Bassir; Levine, Gregory

2013-03-01

In the United States electoral system the election is usually decided by the electoral votes cast by a small number of ``swing states'' where the two candidates historically have roughly equal probabilities of winning. The effective value of a swing state is determined not only by the number of its electoral votes but by the frequency of its appearance in the set of winning partitions of the electoral college. Since the electoral vote values of swing states are not identical, the presence or absence of a state in a winning partition is generally correlated with the frequency of appearance of other states and, hence, their effective values. We quantify the effective value of states by an electoral susceptibility, χj, the variation of the winning probability with the ``cost'' of changing the probability of winning state j. Associating entropy with the logarithm of the number of appearances of a state within the set of winning partitions, the entropy per state (in effect, the chemical potential) is not additive and the states may be said to ``interact.'' We study χj for a simple model with a Zipf's law type distribution of electoral votes. We show that the susceptibility for small states is largest in ``one-sided'' electoral contests and smallest in close contests. This research was supported by Department of Energy DE-FG02-08ER64623, Research Corporation CC6535 (GL) and HHMI Scholar Program (BC)

Modeling interactions between political parties and electors

NASA Astrophysics Data System (ADS)

Bagarello, F.; Gargano, F.

2017-09-01

In this paper we extend some recent results on an operatorial approach to the description of alliances between political parties interacting among themselves and with a basin of electors. In particular, we propose and compare three different models, deducing the dynamics of their related decision functions, i.e. the attitude of each party to form or not an alliance. In the first model the interactions between each party and their electors are considered. We show that these interactions drive the decision functions toward certain asymptotic values depending on the electors only: this is the perfect party, which behaves following the electors' suggestions. The second model is an extension of the first one in which we include a rule which modifies the status of the electors, and of the decision functions as a consequence, at some specific time step. In the third model we neglect the interactions with the electors while we consider cubic and quartic interactions between the parties and we show that we get (slightly oscillating) asymptotic values for the decision functions, close to their initial values. This is the real party, which does not listen to the electors. Several explicit situations are considered in details and numerical results are also shown.

The Convergence Coefficient across Political Systems

PubMed Central

Schofield, Norman

2013-01-01

Formal work on the electoral model often suggests that parties or candidates should locate themselves at the electoral mean. Recent research has found no evidence of such convergence. In order to explain nonconvergence, the stochastic electoral model is extended by including estimates of electoral valence. We introduce the notion of a convergence coefficient, c. It has been shown that high values of c imply that there is a significant centrifugal tendency acting on parties. We used electoral surveys to construct a stochastic valence model of the the elections in various countries. We find that the convergence coefficient varies across elections in a country, across countries with similar regimes, and across political regimes. In some countries, the centripetal tendency leads parties to converge to the electoral mean. In others the centrifugal tendency dominates and some parties locate far from the electoral mean. In particular, for countries with proportional electoral systems, namely, Israel, Turkey, and Poland, the centrifugal tendency is very high. In the majoritarian polities of the United States and Great Britain, the centrifugal tendency is very low. In anocracies, the autocrat imposes limitations on how far from the origin the opposition parties can move. PMID:24385886

The convergence coefficient across political systems.

PubMed

Gallego, Maria; Schofield, Norman

2013-01-01

Formal work on the electoral model often suggests that parties or candidates should locate themselves at the electoral mean. Recent research has found no evidence of such convergence. In order to explain nonconvergence, the stochastic electoral model is extended by including estimates of electoral valence. We introduce the notion of a convergence coefficient, c. It has been shown that high values of c imply that there is a significant centrifugal tendency acting on parties. We used electoral surveys to construct a stochastic valence model of the the elections in various countries. We find that the convergence coefficient varies across elections in a country, across countries with similar regimes, and across political regimes. In some countries, the centripetal tendency leads parties to converge to the electoral mean. In others the centrifugal tendency dominates and some parties locate far from the electoral mean. In particular, for countries with proportional electoral systems, namely, Israel, Turkey, and Poland, the centrifugal tendency is very high. In the majoritarian polities of the United States and Great Britain, the centrifugal tendency is very low. In anocracies, the autocrat imposes limitations on how far from the origin the opposition parties can move.

Production of bio-fuel ethanol from distilled grain waste eluted from Chinese spirit making process.

PubMed

Tan, Li; Sun, Zhaoyong; Zhang, Wenxue; Tang, Yueqin; Morimura, Shigeru; Kida, Kenji

2014-10-01

Distilled grain waste eluted from Chinese spirit making is rich in carbohydrates, and could potentially serve as feedstock for the production of bio-fuel ethanol. Our study evaluated two types of saccharification methods that convert distilled grain waste to monosaccharides: enzymatic saccharification and concentrated H2SO4 saccharification. Results showed that enzymatic saccharification performed unsatisfactorily because of inefficient removal of lignin during pretreatment. Concentrated H2SO4 saccharification led to a total sugar recovery efficiency of 79.0 %, and to considerably higher sugar concentrations than enzymatic saccharification. The process of ethanol production from distilled grain waste based on concentrated H2SO4 saccharification was then studied. The process mainly consisted of concentrated H2SO4 saccharification, solid-liquid separation, decoloration, sugar-acid separation, oligosaccharide hydrolysis, and continuous ethanol fermentation. An improved simulated moving bed system was employed to separate sugars from acid after concentrated H2SO4 saccharification, by which 95.8 % of glucose and 85.8 % of xylose went into the sugar-rich fraction, while 83.3 % of H2SO4 went into the acid-rich fraction. A flocculating yeast strain, Saccharomyces cerevisiae KF-7, was used for continuous ethanol fermentation, which produced an ethanol yield of 91.9-98.9 %, based on glucose concentration.

Ag nanocluster-based color converters for white organic light-emitting devices

NASA Astrophysics Data System (ADS)

Nishikitani, Yoshinori; Takizawa, Daisuke; Uchida, Soichi; Lu, Yue; Nishimura, Suzushi; Oyaizu, Kenichi; Nishide, Hiroyuki

2017-11-01

The authors present Ag nanocluster-based color converters (Ag NC color converters), which convert part of the blue light from a light source to yellow light so as to create white organic light-emitting devices that could be suitable for lighting systems. Ag NCs synthesized by poly(methacrylic acid) template methods have a statistical size distribution with a mean diameter of around 4.5 nm, which is larger than the Fermi wavelength of around 2 nm. Hence, like free electrons in metals, the Ag NC electrons are thought to form a continuous energy band, leading to the formation of surface plasmons by photoexcitation. As for the fluorescence emission mechanism, the fact that the photoluminescence is excitation wavelength dependent suggests that the fluorescence originates from surface plasmons in Ag NCs of different sizes. By using Ag NC color converters and suitable blue light sources, white organic light-emitting devices can be fabricated based on the concept of light-mixing. For our blue light sources, we used polymer light-emitting electrochemical cells (PLECs), which, like organic light-emitting diodes, are area light sources. The PLECs were fabricated with a blue fluorescent π-conjugated polymer, poly[(9,9-dihexylfluoren-2,7-diyl)-co-(anthracen-9,10-diyl)] (PDHFA), and a polymeric solid electrolyte composed of poly(ethylene oxide) and KCF3SO3. In this device structure, the Ag NC color converter absorbs blue light from the PDHFA-based PLEC (PDHFA-PLEC) and then emits yellow light. When the PDHFA-PLEC is turned on by applying an external voltage, pure white light emission can be produced with Commission Internationale de l'Eclairage coordinates of (x = 0.32, y = 0.33) and a color rendering index of 93.6. This study shows that utilization of Ag NC color converters and blue PLECs is a very promising and highly effective method for realizing white organic light-emitting devices.

Status and perspectives for the electron beam technology for flue gases treatment

NASA Astrophysics Data System (ADS)

Frank, Norman W.

The electron-beam process is one of the most effective methods of removing SO 2 and NO x from industrial flue gases. This flue gas treatment consists of adding a small amount of ammonia to the flue gas and irradiating the gas by means of an electron beam, thereby causing reactions which convert the SO 2 and NO x to ammonium sulfate and ammonium sulfate-nitrate. These salts may the be collected from the flue gas by means of such conventional collectors as an electrostatic precipitator or baghouse. This process has numerous advantages over currently-used conventional processes as follows: (1) the process simultaneously removes SO 2 and NO x from flue gas at high efficiency levels; (2) it is a dry process which is easily controlled and has excellent load-following capability; (3) stack-gas reheat is not required; (4) the pollutants are converted into a saleable agricultural fertilizer; (5) the process has low capital and operating cost requirements. The history of the process is shown with a summary of the work that is presently underway. All of the current work is for the purpose of fine tuning the process for commercial usage. It is believed that with current testing and improvements, the process will be very competitive with existing processes and it will find its place in an environmental conscious world.

A Fully Integrated Sensor SoC with Digital Calibration Hardware and Wireless Transceiver at 2.4 GHz

PubMed Central

Kim, Dong-Sun; Jang, Sung-Joon; Hwang, Tae-Ho

2013-01-01

A single-chip sensor system-on-a-chip (SoC) that implements radio for 2.4 GHz, complete digital baseband physical layer (PHY), 10-bit sigma-delta analog-to-digital converter and dedicated sensor calibration hardware for industrial sensing systems has been proposed and integrated in a 0.18-μm CMOS technology. The transceiver's building block includes a low-noise amplifier, mixer, channel filter, receiver signal-strength indicator, frequency synthesizer, voltage-controlled oscillator, and power amplifier. In addition, the digital building block consists of offset quadrature phase-shift keying (OQPSK) modulation, demodulation, carrier frequency offset compensation, auto-gain control, digital MAC function, sensor calibration hardware and embedded 8-bit microcontroller. The digital MAC function supports cyclic redundancy check (CRC), inter-symbol timing check, MAC frame control, and automatic retransmission. The embedded sensor signal processing block consists of calibration coefficient calculator, sensing data calibration mapper and sigma-delta analog-to-digital converter with digital decimation filter. The sensitivity of the overall receiver and the error vector magnitude (EVM) of the overall transmitter are −99 dBm and 18.14%, respectively. The proposed calibration scheme has a reduction of errors by about 45.4% compared with the improved progressive polynomial calibration (PPC) method and the maximum current consumption of the SoC is 16 mA. PMID:23698271

A 2×1 Coplanar Monopole Antenna Structure for Wireless RF Energy Harvesting

NASA Astrophysics Data System (ADS)

Mathur, Monika; Agarwal, Ankit; Singh, Ghanshyam; Bhatnagar, S. K.

2018-03-01

The objective of this paper is to design an efcient wireless energy harvesting (WEH) system to eliminate the problem to continuous charging of a battery operated electronics devices. Most of the devices are battery operated so charging of a battery time to time is serious issue. This WEH system receives the Radio Frequency (RF) and Microwave frequency signals present in the atmosphere and converting it into DC signal so that it can stores in Capacitor or charges a battery for utilize the power. For this RF energy harvesting purposes 21 antenna array structure of the coplanar monopole antenna is presented. This structure shows the gain of 10.2 dBi and 83% efciency. This structure is designed for resonating on multiple bands (Radio, GSM, ISM, and UWB). It is useful for this application because it covers almost all useful bands in the maximum capturing area. The antenna can be connected directly to an RF-DC converter module and it uses about 60% of the total PCB area. And RF to DC convertor circuit can be implemented in that remaining 40% area on the same substrate so it eliminates the need of port connectors and impedance matching circuit between them. This design is worked in receiving mode only when used for energy harvesting purposes. This may be useful for the biomedical and satellite applications.

Solute-enhanced production of gamma-valerolactone (GVL) from aqueous solutions of levulinic acid

DOEpatents

Dumesic, James A.; Wettstein, Stephanie G.; Alonso, David Martin; Gurbuz, Elif Ispir

2016-06-28

A method to produce levulinic acid (LA) and gamma-valerolactone (GVL) from biomass-derived cellulose or lignocellulose by selective extraction of LA using GVL and optionally converting the LA so isolated into GVL, with no purifications steps required to yield the GVL.

Solute-enhanced production of gamma-valerolactone (GVL) from aqueous solutions of levulinic acid

DOEpatents

Dumesic, James A; Wettstein, Stephanie G; Alonso, David Martin; Gurbuz, Elif Ispir

2015-02-24

A method to produce levulinic acid (LA) and gamma-valerolactone (GVL) from biomass-derived cellulose or lignocellulose by selective extraction of LA using GVL and optionally converting the LA so isolated into GVL, with no purifications steps required to yield the GVL.

Changes in SO2 and NO2 Pollution over the Past Decade Observed by Aura OMI

NASA Astrophysics Data System (ADS)

Krotkov, N. A.; Li, C.; Lamsal, L. N.; Celarier, E. A.; Marchenko, S. V.; Swartz, W.; Bucsela, E. J.; Fioletov, V.; McLinden, C. A.; Joiner, J.; Bhartia, P. K.; Duncan, B. N.; Dickerson, R. R.

2014-12-01

The Ozone Monitoring Instrument (OMI), a NASA partnership with the Netherlands and Finland, flies on the EOS Aura satellite and uses reflected sunlight to measure two critical atmospheric trace gases, nitrogen dioxide (NO2) and sulfur dioxide (SO2), characterizing daily air quality. Both gases and the secondary pollutants they produce (particulate matter, PM2.5, and tropospheric ozone) are among USEPA designated criteria pollutants, posing serious threats to human health and the environment (e.g., acid rain, plant damage, and reduced visibility). A new generation of the OMI standard SO2 and NO2 products (based on critically improved DOAS spectral fitting for NO2 and innovative Principal Component Analysis method for SO2) provides a valuable dataset for studying anthropogenic pollution on local to global scales. Here we highlight some of the OMI observed long-term changes in air quality over several regions. Over the US, average NO2 and SO2 pollution levels have decreased dramatically as a result of both technological improvements (e.g., catalytic converters on cars) and stricter regulations of emissions. We see continued decline in NO2 and SO2 pollution over Europe. Over China OMI observed a ~ 60% increase in NO2 pollution between 2005 and 2013, despite a temporary reversal of the growing trend due to both 2008 Olympic Games and the economic recession in 2009. Chinese SO2 pollution seems to have stabilized since peaking in 2007, probably due to government efforts to curb SO2 emissions from the power sector. We have also observed large increases in both SO2 and NO2 pollution particularly in Eastern India where a number of new large coal power plants have been built in recent years. We expect that further improvements in the OMI NO2 and SO2 products will allow more robust quantification of long-term trends in local to global air quality.

Fabrication and luminescent properties of La2O2S:Eu3+ translucent ceramic by pressureless reaction sintering

NASA Astrophysics Data System (ADS)

Lian, Jingbao; Wang, Bingxin; Liang, Ping; Liu, Feng; Wang, Xuejiao

2014-04-01

La2O2S:Eu3+ translucent ceramic (LOS:Eu) was fabricated by pressureless reaction sintering method. It is found that the (La, Eu)2(OH)4SO4ṡ2H2O precursor is synthesized by co-precipitation using commercially available La(NO3)3, Eu(NO3)3, (NH4)2SO4 and NH3ṡH2O as the starting materials. And this precursor can be converted into pure La2O2SO4:Eu3+ phosphor by calcination at 800 °C for 1 h in air, which is composed of a few small needle agglomerated particles. Then the La2O2SO4:Eu3+ phosphor compact can be sintered into the LOS:Eu at 1500 °C for 2 h in the hybrid atmosphere of flowing hydrogen and argon. Under 387 nm UV light excitation, the LOS:Eu reveals a red light emission at 628 nm as the most prominent peak, which corresponds to the 5D0 → 7F2 transition of Eu3+ ions.

Fluid bed gasification--plasma converter process generating energy from solid waste: experimental assessment of sulphur species.

PubMed

Morrin, Shane; Lettieri, Paola; Chapman, Chris; Taylor, Richard

2014-01-01

Often perceived as a Cinderella material, there is growing appreciation for solid waste as a renewable content thermal process feed. Nonetheless, research on solid waste gasification and sulphur mechanisms in particular is lacking. This paper presents results from two related experiments on a novel two stage gasification process, at demonstration scale, using a sulphur-enriched wood pellet feed. Notable SO2 and relatively low COS levels (before gas cleaning) were interesting features of the trials, and not normally expected under reducing gasification conditions. Analysis suggests that localised oxygen rich regions within the fluid bed played a role in SO2's generation. The response of COS to sulphur in the feed was quite prompt, whereas SO2 was more delayed. It is proposed that the bed material sequestered sulphur from the feed, later aiding SO2 generation. The more reducing gas phase regions above the bed would have facilitated COS--hence its faster response. These results provide a useful insight, with further analysis on a suite of performed experiments underway, along with thermodynamic modelling. Copyright © 2013 Elsevier Ltd. All rights reserved.

The NOXSO clean coal project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Black, J.B.; Woods, M.C.; Friedrich, J.J.

1997-12-31

The NOXSO Clean Coal Project will consist of designing, constructing, and operating a commercial-scale flue-gas cleanup system utilizing the NOXSO Process. The process is a waste-free, dry, post-combustion flue-gas treatment technology which uses a regenerable sorbent to simultaneously adsorb sulfur dioxide (SO{sub 2}) and nitrogen oxides (NO{sub x}) from flue gas from coal-fired boilers. The NOXSO plant will be constructed at Alcoa Generating Corporation`s (AGC) Warrick Power Plant near Evansville, Indiana and will treat all the flue gas from the 150-MW Unit 2 boiler. The NOXSO plant is being designed to remove 98% of the SO{sub 2} and 75% ofmore » the NO{sub x} when the boiler is fired with 3.4 weight percent sulfur, southern-Indiana coal. The NOXSO plant by-product will be elemental sulfur. The elemental sulfur will be shipped to Olin Corporation`s Charleston, Tennessee facility for additional processing. As part of the project, a liquid SO{sub 2} plant has been constructed at this facility to convert the sulfur into liquid SO{sub 2}. The project utilizes a unique burn-in-oxygen process in which the elemental sulfur is oxidized to SO{sub 2} in a stream of compressed oxygen. The SO{sub 2} vapor will then be cooled and condensed. The burn-in-oxygen process is simpler and more environmentally friendly than conventional technologies. The liquid SO{sub 2} plant produces 99.99% pure SO{sub 2} for use at Olin`s facilities. The $82.8 million project is co-funded by the US Department of Energy (DOE) under Round III of the Clean Coal Technology program. The DOE manages the project through the Pittsburgh Energy Technology Center (PETC).« less

Comparison of the gaseous and particulate matter emissions from the combustion of agricultural and forest biomasses.

PubMed

Brassard, Patrick; Palacios, Joahnn H; Godbout, Stéphane; Bussières, Denis; Lagacé, Robert; Larouche, Jean-Pierre; Pelletier, Frédéric

2014-03-01

The aim of this study was to compare gaseous and particulate matter (PM) emissions from the combustion of agricultural (switchgrass, fast-growing willow and the dried solid fraction of pig manure) and forest (wood mixture of Black Spruce and Jack Pine) biomasses in a small-scale unit (17.58kW). Concentrations of CO2, CO, CH4, NO2, NH3, N2O, SO2, HCl, and H2O were measured by Fourier transform infrared spectroscopy and converted into emission rates. Opacity was also evaluated and particulates were sampled. Results showed significantly higher emissions of SO2, NO2 and PM with the combustion of agricultural biomass compared to the forest biomass. However, further studies should be carried out so regulations can be adapted in order to permit the combustion of agricultural biomass in small-scale combustion units. Copyright © 2013 Elsevier Ltd. All rights reserved.

Electoral College.

ERIC Educational Resources Information Center

Goldstein, Joel K.

1996-01-01

Examines one of the least understood institutions of U.S. politics, the Electoral College. Discusses the historical circumstances resulting in its creation as well as the current structure and membership. Provides arguments for and against continuation of the Electoral College. (MJP)

Wireless power charging using point of load controlled high frequency power converters

DOEpatents

Miller, John M.; Campbell, Steven L.; Chambon, Paul H.; Seiber, Larry E.; White, Clifford P.

2015-10-13

An apparatus for wirelessly charging a battery of an electric vehicle is provided with a point of load control. The apparatus includes a base unit for generating a direct current (DC) voltage. The base unit is regulated by a power level controller. One or more point of load converters can be connected to the base unit by a conductor, with each point of load converter comprising a control signal generator that transmits a signal to the power level controller. The output power level of the DC voltage provided by the base unit is controlled by power level controller such that the power level is sufficient to power all active load converters when commanded to do so by any of the active controllers, without generating excessive power that may be otherwise wasted.

Method for converting asbestos to non-carcinogenic compounds

DOEpatents

Selby, Thomas W.

1996-01-01

Hazardous and carcinogenic asbestos waste characterized by a crystalline fibrous structure is transformed into non-carcinogenic, relatively nonhazardous, and non-crystalline solid compounds and gaseous compounds which have commercial utilization. The asbestos waste is so transformed by the complete fluorination of the crystalline fibrous silicate mineral defining the asbestos.

Method for converting asbestos to non-carcinogenic compounds

DOEpatents

Selby, T.W.

1996-08-06

Hazardous and carcinogenic asbestos waste characterized by a crystalline fibrous structure is transformed into non-carcinogenic, relatively nonhazardous, and non-crystalline solid compounds and gaseous compounds which have commercial utilization. The asbestos waste is so transformed by the complete fluorination of the crystalline fibrous silicate mineral defining the asbestos. 7 figs.

Offering a Framework for Value Co-Creation in Virtual Academic Learning Environments

ERIC Educational Resources Information Center

Ranjbarfard, Mina; Heidari Sureshjani, Mahboobeh

2018-01-01

Purpose: This research aims to convert the traditional teacher-student models, in which teachers determine the learning resources, into a flexible structure and an active learning environment so that students can participate in the educational processes and value co-creation in virtual academic learning environments (VALEs).…

A Comparison of Approaches for Solving Hard Graph-Theoretic Problems

DTIC Science & Technology

2015-04-29

can be converted to a quadratic unconstrained binary optimization ( QUBO ) problem that uses 0/1-valued variables, and so they are often used...Frontiers in Physics, 2:5 (12 Feb 2014). [7] “Programming with QUBOs ,” (instructional document) D-Wave: The Quantum Computing Company, 2013. [8

Blood pressure reprogramming adapter assists signal recording

NASA Technical Reports Server (NTRS)

Vick, H. A.

1967-01-01

Blood pressure reprogramming adapter separates the two components of a blood pressure signal, a dc pressure signal and an ac Korotkoff sounds signal, so that the Korotkoff sounds are recorded on one channel as received while the dc pressure signal is converted to FM and recorded on a second channel.

Electronically-Scanned Pressure Sensors

NASA Technical Reports Server (NTRS)

Coe, C. F.; Parra, G. T.; Kauffman, R. C.

1984-01-01

Sensors not pneumatically switched. Electronic pressure-transducer scanning system constructed in modular form. Pressure transducer modules and analog to digital converter module small enough to fit within cavities of average-sized wind-tunnel models. All switching done electronically. Temperature controlled environment maintained within sensor modules so accuracy maintained while ambient temperature varies.

Method of removing SO.sub.2, NO.sub.X and particles from gas mixtures using streamer corona

DOEpatents

Mizuno, Akira; Clements, Judson S.

1987-01-01

A method for converting sulfur dioxide and/or nitrogen oxide gases to acid mist and or particle aerosols is disclosed in which the gases are passed through a streamer corona discharge zone having electrodes of a wire-cylinder or wire-plate geometry.

40 CFR 75.31 - Initial missing data procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Initial missing data procedures. 75.31... (CONTINUED) CONTINUOUS EMISSION MONITORING Missing Data Substitution Procedures § 75.31 Initial missing data.... For each hour of missing SO2, Hg, or CO2 emissions concentration data (including CO2 data converted...

“Artificial Leaf” Turns Carbon Dioxide Into Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Researchers at Argonne and the University of Illinois at Chicago have found a way to convert carbon dioxide into a usable energy source using sunlight. The process is similar to photosynthesis, the way plants make fuel from light, so the system is called the “artificial leaf.”

26 CFR 1.1245-3 - Definition of section 1245 property.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., or as an integral part of furnishing transportation, communications, electrical energy, gas, water... involuntarily converted into, or exchanged in a like kind exchange for, the property) was so used by the taxpayer or another taxpayer. For rules applicable to involuntary conversions and like kind exchanges, see...

Emissions of sulfur trioxide from coal-fired power plants.

PubMed

Srivastava, R K; Miller, C A; Erickson, C; Jambhekar, R

2004-06-01

Emissions of sulfur trioxide (SO3) are a key component of plume opacity and acid deposition. Consequently, these emissions need to be low enough to not cause opacity violations and acid deposition. Generally, a small fraction of sulfur (S) in coal is converted to SO3 in coal-fired combustion devices such as electric utility boilers. The emissions of SO3 from such a boiler depend on coal S content, combustion conditions, flue gas characteristics, and air pollution devices being used. It is well known that the catalyst used in the selective catalytic reduction (SCR) technology for nitrogen oxides control oxidizes a small fraction of sulfur dioxide in the flue gas to SO3. The extent of this oxidation depends on the catalyst formulation and SCR operating conditions. Gas-phase SO3 and sulfuric acid, on being quenched in plant equipment (e.g., air preheater and wet scrubber), result in fine acidic mist, which can cause increased plume opacity and undesirable emissions. Recently, such effects have been observed at plants firing high-S coal and equipped with SCR systems and wet scrubbers. This paper investigates the factors that affect acidic mist production in coal-fired electric utility boilers and discusses approaches for mitigating emission of this mist.

Estimation of sulphur dioxide emission rate from a power plant based on the remote sensing measurement with an imaging-DOAS instrument

NASA Astrophysics Data System (ADS)

Chong, Jihyo; Kim, Young J.; Baek, Jongho; Lee, Hanlim

2016-10-01

Major anthropogenic sources of sulphur dioxide in the troposphere include point sources such as power plants and combustion-derived industrial sources. Spatially resolved remote sensing of atmospheric trace gases is desirable for better estimation and validation of emission from those sources. It has been reported that Imaging Differential Optical Absorption Spectroscopy (I-DOAS) technique can provide the spatially resolved two-dimensional distribution measurement of atmospheric trace gases. This study presents the results of I-DOAS observations of SO2 from a large power plant. The stack plume from the Taean coal-fired power plant was remotely sensed with an I-DOAS instrument. The slant column density (SCD) of SO2 was derived by data analysis of the absorption spectra of the scattered sunlight measured by an I-DOAS over the power plant stacks. Two-dimensional distribution of SO2 SCD was obtained over the viewing window of the I-DOAS instrument. The measured SCDs were converted to mixing ratios in order to estimate the rate of SO2 emission from each stack. The maximum mixing ratio of SO2 was measured to be 28.1 ppm with a SCD value of 4.15×1017 molecules/cm2. Based on the exit velocity of the plume from the stack, the emission rate of SO2 was estimated to be 22.54 g/s. Remote sensing of SO2 with an I-DOAS instrument can be very useful for independent estimation and validation of the emission rates from major point sources as well as area sources.

Analog-to-digital conversion techniques for precision photometry

NASA Technical Reports Server (NTRS)

Opal, Chet B.

1988-01-01

Three types of analog-to-digital converters are described: parallel, successive-approximation, and integrating. The functioning of comparators and sample-and-hold amplifiers is explained. Differential and integral linearity are defined, and good and bad examples are illustrated. The applicability and relative advantages of the three types of converters for precision astronomical photometric measurements are discussed. For most measurements, integral linearity is more important than differential linearity. Successive-approximation converters should be used with multielement solid state detectors because of their high speed, but dual slope integrating converters may be superior for use with single element solid state detectors where speed of digitization is not a factor. In all cases, the input signal should be tailored so that they occupy the upper part of the converter's dynamic range; this can be achieved by providing adjustable gain, or better by varying the integration time of the observation if possible.

Sox17 drives functional engraftment of endothelium converted from non-vascular cells.

PubMed

Schachterle, William; Badwe, Chaitanya R; Palikuqi, Brisa; Kunar, Balvir; Ginsberg, Michael; Lis, Raphael; Yokoyama, Masataka; Elemento, Olivier; Scandura, Joseph M; Rafii, Shahin

2017-01-16

Transplanting vascular endothelial cells (ECs) to support metabolism and express regenerative paracrine factors is a strategy to treat vasculopathies and to promote tissue regeneration. However, transplantation strategies have been challenging to develop, because ECs are difficult to culture and little is known about how to direct them to stably integrate into vasculature. Here we show that only amniotic cells could convert to cells that maintain EC gene expression. Even so, these converted cells perform sub-optimally in transplantation studies. Constitutive Akt signalling increases expression of EC morphogenesis genes, including Sox17, shifts the genomic targeting of Fli1 to favour nearby Sox consensus sites and enhances the vascular function of converted cells. Enforced expression of Sox17 increases expression of morphogenesis genes and promotes integration of transplanted converted cells into injured vessels. Thus, Ets transcription factors specify non-vascular, amniotic cells to EC-like cells, whereas Sox17 expression is required to confer EC function.

Apparatus for purifying exhaust gases of internal combustion engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kakinuma, O.; Oya, H.

1980-06-03

Apparatus for purifying the exhaust gases of internal combustion engines is disclosed is comprised of a pair of upstream exhaust pipes, a catalytic converter, and a downstream exhaust pipe. The catalytic converter comprises a shell having an inlet chamber, catalyst chamber, and an outlet chamber. The axial lines of the inlet ports are arranged to cross each other in the inlet chamber at a position near, but upstream of, the upstream facing end of said monolithic catalyst element, so that gas flow can diffuse to the entire plane of the element.

Fighting the Hobbesian Trinity in Columbia: A New Strategy for Peace

DTIC Science & Technology

2001-04-01

that corruption can be avoided in an electoral system, nor do they address the issue that the electoral system can be used to maintain corrupt elites...Yet when corruption assists elites to manipulate the electoral system, then accountability, the very purpose of the electoral system, is nullified. In...Ibid., p. 375. 98. Paz y Derechos Humanos, “Mininterior dice que armar a civiles aumentaria violencia; No a milicias: Gobierno,” El Colombiano, November

Evaluation of Redoubt Volcano's sulfur dioxide emissions by the Ozone Monitoring Instrument

USGS Publications Warehouse

Lopez, Taryn; Carn, Simon A.; Werner, Cynthia A.; Fee, David; Kelly, Peter; Doukas, Michael P.; Pfeffer, Melissa; Webley, Peter; Cahill, Catherine F.; Schneider, David

2013-01-01

The 2009 eruption of Redoubt Volcano, Alaska, provided a rare opportunity to compare satellite measurements of sulfur dioxide (SO2) by the Ozone Monitoring Instrument (OMI) with airborne SO2 measurements by the Alaska Volcano Observatory (AVO). Herein we: (1) compare OMI and airborne SO2 column density values for Redoubt's tropospheric plume, (2) calculate daily SO2 masses from Mount Redoubt for the first three months of the eruption, (3) develop simple methods to convert daily measured SO2 masses into emission rates to allow satellite data to be directly integrated with the airborne SO2 emissions dataset, (4) calculate cumulative SO2 emissions from the eruption, and (5) evaluate OMI as a monitoring tool for high-latitude degassing volcanoes. A linear correlation (R2 ~ 0.75) is observed between OMI and airborne SO2 column densities. OMI daily SO2 masses for the sample period ranged from ~ 60.1 kt on 24 March to below detection limit, with an average daily SO2 mass of ~ 6.7 kt. The highest SO2 emissions were observed during the initial part of the explosive phase and the emissions exhibited an overall decreasing trend with time. OMI SO2 emission rates were derived using three methods and compared to airborne measurements. This comparison yields a linear correlation (R2 ~ 0.82) with OMI-derived emission rates consistently lower than airborne measurements. The comparison results suggest that OMI's detection limit for high latitude, springtime conditions varies from ~ 2000 to 4000 t/d. Cumulative SO2 masses calculated from daily OMI data for the sample period are estimated to range from 542 to 615 kt, with approximately half of this SO2 produced during the explosive phase of the eruption. These cumulative masses are similar in magnitude to those estimated for the 1989–90 Redoubt eruption. Strong correlations between daily OMI SO2 mass and both tephra mass and acoustic energy during the explosive phase of the eruption suggest that OMI data may be used to infer relative eruption size and explosivity. Further, when used in conjunction with complementary datasets, OMI daily SO2 masses may be used to help distinguish explosive from effusive activity and identify changes in lava extrusion rates. The results of this study suggest that OMI is a useful volcano monitoring tool to complement airborne measurements, capture explosive SO2 emissions, and provide high temporal resolution SO2 emissions data that can be used with interdisciplinary datasets to illuminate volcanic processes.

Production of sulfate radical and hydroxyl radical by reaction of ozone with peroxymonosulfate: a novel advanced oxidation process.

PubMed

Yang, Yi; Jiang, Jin; Lu, Xinglin; Ma, Jun; Liu, Yongze

2015-06-16

In this work, simultaneous generation of hydroxyl radical (•OH) and sulfate radical (SO4•−) by the reaction of ozone (O3) with peroxymonosulfate (PMS; HSO5−) has been proposed and experimentally verified. We demonstrate that the reaction between the anion of PMS (i.e.,SO52−) and O3 is primarily responsible for driving O3 consumption with a measured second order rate constant of (2.12 ± 0.03) × 10(4) M(-1) s(-1). The formation of both •OH and SO4•− from the reaction between SO52− and O3 is confirmed by chemical probes (i.e., nitrobenzene for •OH and atrazine forb oth •OH and SO4•−). The yields of •OH and SO4•− are determined to be 0.43 ± 0.1 and 0.45 ± 0.1 per mol of O3 consumption, respectively. An adduct,−O3SOO− + O3 → −O3SO5−, is assumed as the first step, which further decomposes into SO5•− and O3•−. The subsequent reaction of SO5•− with O3is proposed to generate SO4•−, while O3•− converts to •OH. A definition of R(ct,•OH) and R(ct,SO4•−) (i.e., respective ratios of •OH and SO4•− exposures to O3 exposure) is adopted to quantify relative contributions of •OH and SO4•−. Increasing pH leads to increases in both values of R(ct,•OH) and R(ct,SO4•−) but does not significantly affect the ratio of R(ct,SO4•−) to R(ct,•OH) (i.e., R(ct,SO4•−)/R(ct,•OH)), which represents the relative formation of SO4•− to •OH. The presence of bicarbonate appreciably inhibits the degradation of probes and fairly decreases the relative contribution of •OH for their degradation, which may be attributed to the conversion of both •OH and SO4•− to the more selective carbonate radical (CO3•−).Humic acid promotes O3 consumption to generate •OH and thus leads to an increase in the R(ct,•OH) value in the O3/PMS process,w hile humic acid has negligible influence on the R(ct,SO4•−) value. This discrepancy is reasonably explained by the negligible effect of humic acid on SO4•− formation and a lower rate constant for the reaction of humic acid with SO4•− than with •OH. In addition, the efficacy of the O3/PMS process in real water is also confirmed.

The Impact of Politics 2.0 in the Spanish Social Media: Tracking the Conversations around the Audiovisual Political Wars

NASA Astrophysics Data System (ADS)

Noguera, José M.; Correyero, Beatriz

After the consolidation of weblogs as interactive narratives and producers, audiovisual formats are gaining ground on the Web. Videos are spreading all over the Internet and establishing themselves as a new medium for political propaganda inside social media with tools so powerful like YouTube. This investigation proceeds in two stages: on one hand we are going to examine how this audiovisual formats have enjoyed an enormous amount of attention in blogs during the Spanish pre-electoral campaign for the elections of March 2008. On the other hand, this article tries to investigate the social impact of this phenomenon using data from a content analysis of the blog discussion related to these videos centered on the most popular Spanish political blogs. Also, we study when the audiovisual political messages (made by politicians or by users) "born" and "die" in the Web and with what kind of rules they do.

What use do people make of physicians in checking their skin for cancer?

PubMed

Del Mar, C B; Stanton, W R; Gillespie, A M; Lowe, J B; Balanda, K P

1996-01-01

We administered a questionnaire to 995 people selected randomly from the electoral roll in one coastal region of subtropical Australia. Three-quarters (739) indicated their skin was checked by a physician, by themselves, or both. Among the 15% who were taught to check their skin, 59% learned to do so from physicians. A family physician would be consulted immediately by 40% who found something suspicious, and by 58% after a period of delay. Several factors associated with other indicators of health-seeking behavior, including being told by a physician that there was a special risk of skin cancer, were related to an increased proportion of respondents who were checked by their physicians as well as themselves. In addition to being the main focus of help should a suspicious lesion be found, physicians may have an important role in introducing the public to the process of early detection of skin cancer as well as providing an important function in its actual conduct.

Optimal decision making modeling for copper-matte Peirce-Smith converting process by means of data mining

NASA Astrophysics Data System (ADS)

Song, Yanpo; Peng, Xiaoqi; Tang, Ying; Hu, Zhikun

2013-07-01

To improve the operation level of copper converter, the approach to optimal decision making modeling for coppermatte converting process based on data mining is studied: in view of the characteristics of the process data, such as containing noise, small sample size and so on, a new robust improved ANN (artificial neural network) modeling method is proposed; taking into account the application purpose of decision making model, three new evaluation indexes named support, confidence and relative confidence are proposed; using real production data and the methods mentioned above, optimal decision making model for blowing time of S1 period (the 1st slag producing period) are developed. Simulation results show that this model can significantly improve the converting quality of S1 period, increase the optimal probability from about 70% to about 85%.

Education for Francisation: The Case of New France in the Seventeenth Century.

ERIC Educational Resources Information Center

Jaenen, Cornelius J.

1983-01-01

Discusses the seventeenth-century French missionary and bureaucratic attempt to "francisize" (to make French) Canadian Indian children, so they would eventually be assimilated into the French expatriate colony, an effort based on the idea that contact with Europeans and education would convert Amerindians to Catholicism and make them…

The History Teacher as Propagandist

ERIC Educational Resources Information Center

Birn, Donald S.

1972-01-01

During the post war years the League of Nations Union Movement in Britain worked through the schools and converted pro-league sentiment into specific government policies. The history classroom was the focal point of the L.N.U.'s educational effort so that new generations would grow up ready to support enlightened foreign policies and the work of…

Where High Tech Meets High Concept

ERIC Educational Resources Information Center

Monaghan, Peter

2007-01-01

Shawn Brixey's "Altimira" is a decidedly strange work of art--so strange that he has not, to date, put it on public display. He turns on a device, housed in a basketball-size glass chamber, and it converts rapidly pulsating radio signals emanating from pulsars--collapsed stars that spin violently, sweeping their poles like lighthouses…

Visualization and Image Analysis of Yeast Cells.

PubMed

Bagley, Steve

2016-01-01

When converting real-life data via visualization to numbers and then onto statistics the whole system needs to be considered so that conversion from the analogue to the digital is accurate and repeatable. Here we describe the points to consider when approaching yeast cell analysis visualization, processing, and analysis of a population by screening techniques.

VHDL Implementation of Sigma-Delta Analog To Digital Converter

NASA Astrophysics Data System (ADS)

Chavan, R. N.; Chougule, D. G.

2010-11-01

Sigma-Delta modulation techniques provide a range of opportunities in a signal processing system for both increasing performance and data path optimization along the silicon area axis in the design space. One of the most challenging tasks in Analog to Digital Converter (ADC) design is to adapt the circuitry to ever new CMOS process technology. For digital circuits the number of gates per square mm app. doubles per chip generation. Integration of analog parts in newer deep submicron technologies is much more tough and additionally complicated because the usable voltage ranges are decreasing with every new integration step. This paper shows an approach which only uses 2 resistors and 1 capacitor which are located outside a pure digital chip. So all integration advantages of pure digital chips are preserved, there is no design effort for a new chip generation and the ADC also can be used for FPGAs. Resolutions of up to 16 bit are achievable. Sample rates in the 1 MHz region are feasible so that the approach is also useful for ADCs for xDSL technologies.

Water vapor inhibits hydrogen sulfide detection in pulsed fluorescence sulfur monitors

NASA Astrophysics Data System (ADS)

Bluhme, Anders B.; Ingemar, Jonas L.; Meusinger, Carl; Johnson, Matthew S.

2016-06-01

The Thermo Scientific 450 Hydrogen Sulfide-Sulfur Dioxide Analyzer measures both hydrogen sulfide (H2S) and sulfur dioxide (SO2). Sulfur dioxide is measured by pulsed fluorescence, while H2S is converted to SO2 with a molybdenum catalyst prior to detection. The 450 is widely used to measure ambient concentrations, e.g., for emissions monitoring and pollution control. An air stream with a constant H2S concentration was generated and the output of the analyzer recorded as a function of relative humidity (RH). The analyzer underreported H2S as soon as the relative humidity was increased. The fraction of undetected H2S increased from 8.3 at 5.3 % RH (294 K) to over 34 % at RH > 80 %. Hydrogen sulfide mole fractions of 573, 1142, and 5145 ppb were tested. The findings indicate that previous results obtained with instruments using similar catalysts should be re-evaluated to correct for interference from water vapor. It is suspected that water decreases the efficiency of the converter unit and thereby reduces the measured H2S concentration.

Mutation rates among RNA viruses

PubMed Central

Drake, John W.; Holland, John J.

1999-01-01

The rate of spontaneous mutation is a key parameter in modeling the genetic structure and evolution of populations. The impact of the accumulated load of mutations and the consequences of increasing the mutation rate are important in assessing the genetic health of populations. Mutation frequencies are among the more directly measurable population parameters, although the information needed to convert them into mutation rates is often lacking. A previous analysis of mutation rates in RNA viruses (specifically in riboviruses rather than retroviruses) was constrained by the quality and quantity of available measurements and by the lack of a specific theoretical framework for converting mutation frequencies into mutation rates in this group of organisms. Here, we describe a simple relation between ribovirus mutation frequencies and mutation rates, apply it to the best (albeit far from satisfactory) available data, and observe a central value for the mutation rate per genome per replication of μg ≈ 0.76. (The rate per round of cell infection is twice this value or about 1.5.) This value is so large, and ribovirus genomes are so informationally dense, that even a modest increase extinguishes the population. PMID:10570172

Theoretical studies of the marine sulfur cycle

NASA Technical Reports Server (NTRS)

Toon, Owen B.; Kasting, James B.; Liu, May S.

1985-01-01

Several reduced sulfur compounds are produced by marine organisms and then enter the atmosphere, where they are oxidized and ultimately returned to the ocean or the land. The oceanic dimethyl sulfide (DMS) flux, in particular, represents a significant fraction of the annual global sulfur input to the atmosphere. In the atmosphere, this gas is converted to sulfur dioxide (SO2), methane sulfonic acid, and other organic acids which are relatively stable and about which little is known. SO2 is a short lived gas which, in turn, is converted to sulfuric acid and other sulfate compounds which contribute significantly to acid rain. Because of the complexity of the sulfur system, it is not well understood even in the unperturbed atmosphere. However, a number of new observations and experiments have led to a significant increase in the understanding of this system. A number of one dimensional model experiments were conducted on the gas phase part of the marine sulfur cycle. The results indicate the measured concentration of DMS and the amplitude of its diurnal cycle are in agreement with estimates of its global flux. It was also found that DMS can make a large contribution to the background SO2 concentration in the free troposphere. Estimates of CS2 concentrations in the atmosphere are inconsistent with estimated fluxes; however, measured reaction rates are consistent with the observed steep tropospheric gradient in CS2. Observations of CS2 are extremely sparse. Further study is planned.

Electro-optical detector for use in a wide mass range mass spectrometer

NASA Technical Reports Server (NTRS)

Giffin, Charles E. (Inventor)

1976-01-01

An electro-optical detector is disclosed for use in a wide mass range mass spectrometer (MS), in the latter the focal plane is at or very near the exit end of the magnetic analyzer, so that a strong magnetic field of the order of 1000G or more is present at the focal plane location. The novel detector includes a microchannel electron multiplier array (MCA) which is positioned at the focal plane to convert ion beams which are focused by the MS at the focal plane into corresponding electron beams which are then accelerated to form visual images on a conductive phosphored surface. These visual images are then converted into images on the target of a vidicon camera or the like for electronic processing. Due to the strong magnetic field at the focal plane, in one embodiment of the invention, the MCA with front and back parallel ends is placed so that its front end forms an angle of not less than several degrees, preferably on the order of 10.degree.-20.degree., with respect to the focal plane, with the center line of the front end preferably located in the focal plane. In another embodiment the MCA is wedge-shaped, with its back end at an angle of about 10.degree.-20.degree. with respect to the front end. In this embodiment the MCA is placed so that its front end is located at the focal plane.

P/N In(Al) GaAs multijunction laser power converters

NASA Technical Reports Server (NTRS)

Wojtczuk, Steven; Parados, Themis; Walker, Gilbert

1994-01-01

Eight In(AI)GaAs PN junctions grown epitaxially on the semi-insulating wafer were monolithically integrated in series to boost the approximately 0.4V photovoltage per typical In(Al)GaAs junction to over 3 volts for the 1 sq cm laser power converted (LPC) chip. Advantages of multijunction LCP designs include the need for less circuitry for power reconditioning and the potential for lower I(sup 2)R power loss. As an example, these LPC's have a responsivity of approximately 1 amp/watt. With a single junction LPC, 100 watts/sq cm incident power would lead to about 100 A/sq cm short-circuit current at approximately 0.4V open-cicuit voltage. One disadvantage is the large current would lead to a large I(sup 2)R loss which would lower the fill factor so that 40 watts/sq cm output would not be obtained. Another is that few circuits are designed to work at 0.4 volts, so DC-DC power conversion circuitry would be necessary to raise the voltage to a reasonable level. The multijunction LPC being developed in this program is a step toward solving these problems. In the above example, an eight-junction LPC would have eight times the voltage, approximately 3V, so that DC-DC power conversion may not be needed in many instances. In addition, the multijunction LPC would have 1/8 the current of a single-junction LPC, for only 1/64 the I(sup 2)R loss if the series resistance is the same. Working monolithic multijunction laser power converters (LPC's) were made in two different compositions of the In(x)Al(y)Ga(1-x-y)As semiconductor alloy, In(0.53)Ga(0.47)As (0.74 eV) and In(0.5)Al(0.1)Ga(0.4)As (0.87 eV). The final 0.8 sq cm LPC's had output voltages of about 3 volts and output currents up to about one-half amp. Maximum 1.3 micron power conversion efficiencies were approximately 22 percent. One key advantage of multijunction LPC's is that they have higher output voltages, so that less DC-DC power conversion circuitry is needed in applications.

Structural and kinetic study of reversible CO2 fixation by dicopper macrocyclic complexes. From intramolecular binding to self-assembly of molecular boxes.

PubMed

Company, Anna; Jee, Joo-Eun; Ribas, Xavi; Lopez-Valbuena, Josep Maria; Gómez, Laura; Corbella, Montserrat; Llobet, Antoni; Mahía, José; Benet-Buchholz, Jordi; Costas, Miquel; van Eldik, Rudi

2007-10-29

A study of the reversible CO2 fixation by a series of macrocyclic dicopper complexes is described. The dicopper macrocyclic complexes [Cu2(OH)2(Me2p)](CF3SO3)2, 1(CF3SO3)2, and [Cu2(mu-OH)2(Me2m)](CF3SO3)2, 2(CF3SO3)2, (Scheme 1) containing terminally bound and bridging hydroxide ligands, respectively, promote reversible inter- and intramolecular CO2 fixation that results in the formation of the carbonate complexes [{Cu2(Me2p)}2(mu-CO3)2](CF3SO3)4, 4(CF3SO3)4, and [Cu2(mu-CO3)(Me2m)](CF3SO3)2, 5(CF3SO3)2. Under a N2 atmosphere the complexes evolve CO2 and revert to the starting hydroxo complexes 1(CF3SO3)2 and 2(CF3SO3)2, a reaction the rate of which linearly depends on [H2O]. In the presence of water, attempts to crystallize 5(CF3SO3)2 afford [{Cu2(Me2m)(H2O)}2(mu-CO3)2](CF3SO3)4, 6(CF3SO3)4, which appears to rapidly convert to 5(CF3SO3)2 in acetonitrile solution. [Cu2(OH)2(H3m)]2+, 7, which contains a larger macrocyclic ligand, irreversibly reacts with atmospheric CO2 to generate cagelike [{Cu2(H3m)}2(mu-CO3)2](ClO4)4, 8(ClO4)4. However, addition of 1 equiv of HClO4 per Cu generates [Cu2(H3m)(CH3CN)4]4+ (3), and subsequent addition of Et3N under air reassembles 8. The carbonate complexes 4(CF3SO3)4, 5(CF3SO3)2, 6(CF3SO3)4, and 8(ClO4)4 have been characterized in the solid state by X-ray crystallography. This analysis reveals that 4(CF3SO3)4, 6(CF3SO3)4, and 8(ClO4)4 consist of self-assembled molecular boxes containing two macrocyclic dicopper complexes, bridged by CO32- ligands. The bridging mode of the carbonate ligand is anti-anti-mu-eta1:eta1 in 4(CF3SO3)4, anti-anti-mu-eta2:eta1 in 6(CF3SO3)4 and anti-anti-mu-eta2:eta2 in 5(CF3SO3)2 and 8(ClO4)4. Magnetic susceptibility measurements on 4(CF3SO3)4, 6(CF3SO3)4, and 8(ClO4)4 indicate that the carbonate ligands mediate antiferromagnetic coupling between each pair of bridged CuII ions (J = -23.1, -108.3, and -163.4 cm-1, respectively, H = -JS1S2). Detailed kinetic analyses of the reaction between carbon dioxide and the macrocyclic complexes 1(CF3SO3)2 and 2(CF3SO3)2 suggest that it is actually hydrogen carbonate formed in aqueous solution on dissolving CO2 that is responsible for the observed formation of the different carbonate complexes controlled by the binding mode of the hydroxy ligands. This study shows that CO2 fixation can be used as an on/off switch for the reversible self-assembly of supramolecular structures based on macrocyclic dicopper complexes.

GIS tool for California state legislature electoral history

NASA Astrophysics Data System (ADS)

Artham, Swathi

The California State Legislature contains two bodies consisting of the lower house, the California State Assembly, with eighty members, and the upper house, the California State Senate, with forty members. Elections are held for every two years for both Senate and Assembly. The terms of the Senators are staggered so that half the membership is elected every two years, whereas all the Assembly members are elected every two years. The electoral district boundaries vary after every 10-year census. My main objective is to provide a summary of both California State Senate and California State Assembly election results in a single GIS tool, from the years 1970 to 2012. This tool provides information about different trends in the California State Senate and State Assembly elections along the years. This tool was designed to help students, and teachers to interactively learn about the California State Legislature elections. Users can view the election results by selecting a particular year for Senate or Assembly, which results in adding a new layer on the map with a coloring scheme for better understanding of change of parties; red for Republicans, blue for Democrats and green for Independents. Users can click on any district shown on the map using a hotlink tool to see the electoral trends for the districts for the past years. This application provides a powerful Stored Query Language (SQL) query option to enter queries and get election results in the form of tables with various fields. This data can be further used to aid other analysis as per user requirements. This tool also provides various visual statistics using graphs and tables for voter turnout, number of candidates won by each party, number of seats changed from one party to another. It also features a color matrix table that helps users to see trends in California State Senate and Assembly. Every two-year election results are shown in the form of graphs and tables for better understanding by the user. The tool provides two quiz options for users who are willing to test the knowledge they gained using the tool. This tool was developed in JAVA swing and AWT, Map Objects Java Objects (MOJO), Apache Derby, DBF Explorer, HTML5, CSS3 and JavaScript.

Enantioconvergent hydrolysis of racemic styrene oxide at high concentration by a pair of novel epoxide hydrolases into (R)-phenyl-1,2-ethanediol.

PubMed

Wang, Rui; Hu, Die; Zong, Xuncheng; Li, Jinping; Ding, Lei; Wu, Minchen; Li, Jianfang

2017-12-01

To prepare (R)-phenyl-1,2-ethanediol ((R)-PED) with high enantiomeric excess (ee p ) and yield from racemic styrene oxide (rac-SO) at high concentration by bi-enzymatic catalysis. The bi-enzymatic catalysis was designed for enantioconvergent hydrolysis of rac-SO by a pair of novel epoxide hydrolases (EHs), a Vigna radiata EH3 (VrEH3) and a variant (AuEH2 A250I ) of Aspergillus usamii EH2. The simultaneous addition mode of VrEH3 and AuEH2 A250I , exhibiting the highest average turnover frequency (aTOF) of 0.12 g h -1 g -1 , was selected, by which rac-SO (10 mM) was converted into (R)-PED with 92.6% ee p and 96.3% yield. Under the optimized reaction conditions: dry weight ratio 14:1 of VrEH3-expressing E. coli/vreh3 to AuEH2 A250I -expressing E. coli/Aueh2 A250I and reaction at 20 °C, rac-SO (10 mM) was completely hydrolyzed in 2.3 h, affording (R)-PED with 98% ee p . At the weight ratio 0.8:1 of rac-SO to two mixed dry cells, (R)-PED with 97.4% ee p and 98.7% yield was produced from 200 mM (24 mg/ml) rac-SO in 10.5 h. Enantioconvergent hydrolysis of rac-SO at high concentration catalyzed by both VrEH3 and AuEH2 A250I is an effective method for preparing (R)-PED with high ee p and yield.

Endogenous sulfur dioxide aggravates myocardial injury in isolated rat heart with ischemia and reperfusion.

PubMed

Zhang, Suqing; Du, Junbao; Jin, Hongfang; Li, Wei; Liang, Yinfang; Geng, Bin; Li, Shukui; Zhang, Chunyu; Tang, Chaoshu

2009-02-27

Ischemia-reperfusion (I/R) injury is an important clinical problem. This article investigated the role of sulfur dioxide (SO2) in the regulation of cardiac function and in the pathogenesis of cardiac I/R injury in isolated rat heart. Rat hearts isolated on a Langendorff apparatus were divided into control, I/R, I/R+SO2, and I/R+hydroxamate groups. Hydroxamate is an inhibitor of SO2 synthetase. I/R treatment was ischemia for 2 hr in hypothermic solution (4 degrees C), then reperfusion/rewarming (37 degrees C) for 60 min. Cardiac function was monitored by MacLab analog to a digital converter. Determination of sulfite content involved reverse-phase high performance liquid chromatography with fluorescence detection. Myoglobin content of coronary perfusate was determined at 410 nm. Myocardial malondialdehyde (MDA) was determined by thiobarbituric acid method, and conjugated diene (CD) was extracted by chloroform. 5,50-Dithiobis-2-nitrobenzoic acid was used to determine glutathione (GSH). The results showed that I/R treatment obviously increased myocardial sulfite content, and sulfite content of myocardium was negatively correlated with the recovery rate of left-ventricle developed pressure and positively correlated with the leakage of myoglobin. In postreperfusion, myocardial function recovery was decreased by SO2. During reperfusion, myocardium-released enzymes, MDA and CD level were increased but myocardial GSH content was depressed with the treatment of SO2 donor. Incubation of myocardial tissue with SO2 significantly increased MDA and CD generation. Endogenous SO2 might be involved in the pathogenesis of myocardial I/R injury, and its mechanism might be associated with an increase in lipid peroxide level and a decrease in GSH generation.

NO2-initiated multiphase oxidation of SO2 by O2 on CaCO3 particles

NASA Astrophysics Data System (ADS)

Yu, Ting; Zhao, Defeng; Song, Xiaojuan; Zhu, Tong

2018-05-01

The reaction of SO2 with NO2 on the surface of aerosol particles has been suggested to be important in sulfate formation during severe air pollution episodes in China. However, we found that the direct oxidation of SO2 by NO2 was slow and might not be the main reason for sulfate formation in ambient air. In this study, we investigated the multiphase reaction of SO2 with an O2 / NO2 mixture on single CaCO3 particles using Micro-Raman spectroscopy. The reaction converted the CaCO3 particle to a Ca(NO3)2 droplet, with CaSO4 ⚫ 2H2O solid particles embedded in it, which constituted a significant fraction of the droplet volume at the end of the reaction. The reactive uptake coefficient of SO2 for sulfate formation was on the order of 10-5, which was higher than that for the multiphase reaction of SO2 directly with NO2 by 2-3 orders of magnitude. According to our observations and the literature, we found that in the multiphase reaction of SO2 with the O2 / NO2 mixture, O2 was the main oxidant of SO2 and was necessary for radical chain propagation. NO2 acted as the initiator of radical formation, but not as the main oxidant. The synergy of NO2 and O2 resulted in much faster sulfate formation than the sum of the reaction rates with NO2 and with O2 alone. We estimated that the multiphase oxidation of SO2 by O2 initiated by NO2 could be an important source of sulfate and a sink of SO2, based on the calculated lifetime of SO2 regarding the loss through the multiphase reaction versus the loss through the gas-phase reaction with OH radicals. Parameterization of the reactive uptake coefficient of the reaction observed in our laboratory for further model simulation is needed, as well as an integrated assessment based on field observations, laboratory study results, and model simulations to evaluate the importance of the reaction in ambient air during severe air pollution episodes, especially in China.

A design method for high performance seismic data acquisition based on oversampling delta-sigma modulation

NASA Astrophysics Data System (ADS)

Gao, Shanghua; Xue, Bing

2017-04-01

The dynamic range of the currently most widely used 24-bit seismic data acquisition devices is 10-20 dB lower than that of broadband seismometers, and this can affect the completeness of seismic waveform recordings under certain conditions. However, this problem is not easy to solve because of the lack of analog to digital converter (ADC) chips with more than 24 bits in the market. So the key difficulties for higher-resolution data acquisition devices lie in achieving more than 24-bit ADC circuit. In the paper, we propose a method in which an adder, an integrator, a digital to analog converter chip, a field-programmable gate array, and an existing low-resolution ADC chip are used to build a third-order 16-bit oversampling delta-sigma modulator. This modulator is equipped with a digital decimation filter, thus forming a complete analog to digital converting circuit. Experimental results show that, within the 0.1-40 Hz frequency range, the circuit board's dynamic range reaches 158.2 dB, its resolution reaches 25.99 dB, and its linearity error is below 2.5 ppm, which is better than what is achieved by the commercial 24-bit ADC chips ADS1281 and CS5371. This demonstrates that the proposed method may alleviate or even solve the amplitude-limitation problem that broadband observation systems so commonly have to face during strong earthquakes.

A large high-efficiency multi-layered Micromegas thermal neutron detector

NASA Astrophysics Data System (ADS)

Tsiledakis, G.; Delbart, A.; Desforge, D.; Giomataris, I.; Menelle, A.; Papaevangelou, T.

2017-09-01

Due to the so-called 3He shortage crisis, many detection techniques used nowadays for thermal neutrons are based on alternative converters. Thin films of 10B or 10B4C are used to convert neutrons into ionizing particles which are subsequently detected in gas proportional counters, but only for small or medium sensitive areas so far. The micro-pattern gaseous detector Micromegas has been developed for several years in Saclay and is used in a wide variety of neutron experiments combining high accuracy, high rate capability, excellent timing properties and robustness. We propose here a large high-efficiency Micromegas-based neutron detector with several 10B4C thin layers mounted inside the gas volume for thermal neutron detection. The principle and the fabrication of a single detector unit prototype with overall dimension of ~ 15 × 15 cm2 and a flexibility of modifying the number of layers of 10B4C neutron converters are described and simulated results are reported, demonstrating that typically five 10B4C layers of 1-2 μm thickness can lead to a detection efficiency of 20-40% for thermal neutrons and a spatial resolution of sub-mm. The design is well adapted to large sizes making possible the construction of a mosaic of several such detector units with a large area coverage and a high detection efficiency, showing the good potential of this novel technique.

The Electoral College

ERIC Educational Resources Information Center

Social Education, 2008

2008-01-01

The United States has a system of voting for a president that is unique among western democracies. Rather than vote directly for a president or entrust the presidential election to a parliament, Americans instead vote for statewide slates of electors who are pledged to a candidate. The successful electors become the members of the Electoral…

Can the coverage of screening for cancer of the cervix be improved using the Electoral Register? A pilot study.

PubMed

Cook, G A; Wald, N J

1985-09-30

We conducted a pilot study to assess the feasibility using the Electoral Register to carry out a cervical cancer screening programme on a Health District basis. A random sample of 500 names and addresses were drawn from a computerised list of the Electoral Register from three Electoral Wards in Oxford. A pilot study showed that the Electoral Register could be used successfully in this way and that the proportion of women aged 35-64 years who had a cervical smear examination as a result of the screening initiative was increased by a quarter, from 64% to 79%. The numbers of women involved at each step of the screening process were determined, and these may provide a useful guide to others considering implementing similar schemes.

Efficient conversion of lignocellulosic biomass to levulinic acid using acidic ionic liquids.

PubMed

Khan, Amir Sada; Man, Zakaria; Bustam, Mohamad Azmi; Nasrullah, Asma; Ullah, Zahoor; Sarwono, Ariyanti; Shah, Faiz Ullah; Muhammad, Nawshad

2018-02-01

In the present research work, dicationic ionic liquids, containing 1,4-bis(3-methylimidazolium-1-yl) butane ([C 4 (Mim) 2 ]) cation with counter anions [(2HSO 4 )(H 2 SO 4 ) 0 ], [(2HSO 4 )(H 2 SO 4 ) 2 ] and [(2HSO 4 )(H 2 SO 4 ) 4 ] were synthesised. ILs structures were confirmed using 1 H NMR spectroscopy. Thermal stability, Hammett acidity, density and viscosity of ILs were determined. Various types of lignocellulosic biomass such as rubber wood, palm oil frond, bamboo and rice husk were converted into levulinic acid (LA). Among the synthesized ionic liquids, [C 4 (Mim) 2 ][(2HSO 4 )(H 2 SO 4 ) 4 ] showed higher % yield of LA up to 47.52 from bamboo biomass at 110°C for 60min, which is the better yield at low temperature and short time compared to previous reports. Surface morphology, surface functional groups and thermal stability of bamboo before and after conversion into LA were studied using SEM, FTIR and TGA analysis, respectively. This one-pot production of LA from agro-waste will open new opportunity for the conversion of sustainable biomass resources into valuable chemicals. Copyright © 2017 Elsevier Ltd. All rights reserved.

A configurable and low-power mixed signal SoC for portable ECG monitoring applications.

PubMed

Kim, Hyejung; Kim, Sunyoung; Van Helleputte, Nick; Artes, Antonio; Konijnenburg, Mario; Huisken, Jos; Van Hoof, Chris; Yazicioglu, Refet Firat

2014-04-01

This paper describes a mixed-signal ECG System-on-Chip (SoC) that is capable of implementing configurable functionality with low-power consumption for portable ECG monitoring applications. A low-voltage and high performance analog front-end extracts 3-channel ECG signals and single channel electrode-tissue-impedance (ETI) measurement with high signal quality. This can be used to evaluate the quality of the ECG measurement and to filter motion artifacts. A custom digital signal processor consisting of 4-way SIMD processor provides the configurability and advanced functionality like motion artifact removal and R peak detection. A built-in 12-bit analog-to-digital converter (ADC) is capable of adaptive sampling achieving a compression ratio of up to 7, and loop buffer integration reduces the power consumption for on-chip memory access. The SoC is implemented in 0.18 μm CMOS process and consumes 32 μ W from a 1.2 V while heart beat detection application is running, and integrated in a wireless ECG monitoring system with Bluetooth protocol. Thanks to the ECG SoC, the overall system power consumption can be reduced significantly.

Physicochemical properties of metal-doped activated carbons and relationship with their performance in the removal of SO2 and NO.

PubMed

Gao, Xiang; Liu, Shaojun; Zhang, Yang; Luo, Zhongyang; Cen, Kefa

2011-04-15

Several metal-doped activated carbons (Fe, Co, Ni, V, Mn, Cu and Ce) were prepared and characterized. The results of N(2) adsorption-desorption, X-ray diffraction, and X-ray photoelectron spectroscopy indicated that some metals (Cu and Fe) were partly reduced by carbon during preparation. Activity tests for the removal of SO(2) and the selective catalytic reduction of NO with ammonia were carried out. Due to different physicochemical properties, different pathways for the SO(2) removal had been put out, i.e., catalytic oxidation, direct reaction and adsorption. This classification depended on the standard reduction potentials of metal redox pairs. Samples impregnated with V, Ce and Cu showed good activity for NO reduction by NH(3), which was also ascribed to the reduction potential values of metal redox pairs. Ce seemed to be a promising alternative to V due to the higher activity in NO reduction and the nontoxic property. A metal cation which could easily convert between the two valences seemed to be crucial to the good performance of both SO(2) and NO removal, just like V and Cu. Copyright © 2011 Elsevier B.V. All rights reserved.

New Tools to Convert PDF Math Contents into Accessible e-Books Efficiently.

PubMed

Suzuki, Masakazu; Terada, Yugo; Kanahori, Toshihiro; Yamaguchi, Katsuhito

2015-01-01

New features in our math-OCR software to convert PDF math contents into accessible e-books are shown. A method for recognizing PDF is thoroughly improved. In addition, contents in any selected area including math formulas in a PDF file can be cut and pasted into a document in various accessible formats, which is automatically recognized and converted into texts and accessible math formulas through this process. Combining it with our authoring tool for a technical document, one can easily produce accessible e-books in various formats such as DAISY, accessible EPUB3, DAISY-like HTML5, Microsoft Word with math objects and so on. Those contents are useful for various print-disabled students ranging from the blind to the dyslexic.

Research on the Control Strategy for Grid-side Converter of PWM Doubly Fed Induction Wind Power Generators

NASA Astrophysics Data System (ADS)

Liu, Yifang; Wang, Zhijie; Li, Renfu; Jiang, Xiuchen; Sheng, Gehao; Liu, Tianyu; Liu, Sanming

2017-05-01

When the grid voltage drop, over current of transient rotor and over voltage may damage the power electronic devices. The attenuation of electromagnetic torque will lead to speed up. This paper proposes an improved feed-forward control strategy and its application in the PWM converter. When the PWM converter on voltage drops, bus voltage will be more stable. So over current problems of the DFIG rotor side can be reduced, and it also can improve voltage regulation speed of the DC bus voltage and reduce the oscillation amplitude. Furthermore, the stability of doubly fed wind generator system can be improved. The simulation results verify the validity of the modified control strategy.

Ultrafast transient grating radiation to optical image converter

DOEpatents

Stewart, Richard E; Vernon, Stephen P; Steel, Paul T; Lowry, Mark E

2014-11-04

A high sensitivity transient grating ultrafast radiation to optical image converter is based on a fixed transmission grating adjacent to a semiconductor substrate. X-rays or optical radiation passing through the fixed transmission grating is thereby modulated and produces a small periodic variation of refractive index or transient grating in the semiconductor through carrier induced refractive index shifts. An optical or infrared probe beam tuned just below the semiconductor band gap is reflected off a high reflectivity mirror on the semiconductor so that it double passes therethrough and interacts with the radiation induced phase grating therein. A small portion of the optical beam is diffracted out of the probe beam by the radiation induced transient grating to become the converted signal that is imaged onto a detector.

What have we learned about global SO2 pollution with Aura/OMI data?

NASA Astrophysics Data System (ADS)

Krotkov, N.; Yang, K.; Bhartia, P. K.; Carn, S.; Krueger, A.; Dickerson, R.; Li, C.

2008-05-01

Sulfur Dioxide (SO2) is a short-lived gas produced by volcanoes, power plants, refineries, metal smelting and general burning of fossil fuels. It is one of five EPA criteria pollutants. Emitted SO2 is soon converted to sulfate aerosol, with climate effects that include direct radiative forcing and aerosol-induced changes in cloud microphysics and the hydrological cycle. The Ozone Monitoring Instrument (OMI) launched on NASA Aura satellite in July 2004 offers unprecedented spatial resolution, coupled with contiguous daily global coverage, for space- based UV measurements of volcanic and anthropogenic SO2 emissions. Anthropogenic SO2 emissions in the PBL present challenges, because these typically weak signals need to be separated from the noise in the radiances. Plumes from strong surface sources of SO2 (such as smelters and coal burning power plants) and from strong regional pollution can currently be detected in the operational pixel data. Operational data were evaluated with in-situ aircraft SO2 profiles measured in the lower troposphere over China during the East-AIRE campaign in April 2005. This comparison demonstrates that OMI can distinguish between background SO2 conditions and heavy pollutions on a daily basis, suggesting potential of using OMI SO2 data for the regional pollution monitoring. Chinese SO2 pollution lofting above the PBL and long-range transport over Pacific Ocean was first confirmed using OMI data. Quantification of anthropogenic SO2 emissions requires off-line corrections of the average photon path, characterized by the operational air-mass factor (AMF). The AMF corrections in turn require a-priori information about the altitude of the SO2 plume center of mass, the total ozone, and surface albedo. In addition, aerosols and subpixel clouds affect the AMF in different ways depending on their amounts and vertical distribution. Therefore, ancillary cloud, snow and aerosol information available from near simultaneous A-train sensors is valuable in quantification of the OMI SO2 burdens. As an example the analysis of the effect of the major Chinese snow storm on the OMI SO2 data will be presented.Spatial smoothing and/or time averaging allow significant signal to noise enhancements. Applying these techniques, power plant emissions in Greece, Bulgaria, Turkey, and the US Ohio River valley as well emissions from Persian Gulf refineries, and plumes in an industrial complex near Mexico City can be seen in OMI data - several previously unknown sources have been detected. Using long-term averages, anthropogenic SO2 burdens can be compared directly in different parts of the world. On-going algorithm improvements such as spectral fitting will allow enhanced sensitivity to enable monitoring of a greater number of SO2 sources.

Demystifying the Electoral College: 12 Frequently Asked Questions

ERIC Educational Resources Information Center

Middleton, Tiffany

2012-01-01

As the presidential election of 2012 draws closer, Americans will witness a resurgence of references to the Electoral College in news reports. Here, "Looking at the Law" hopes to demystify the Electoral College, and refresh many social studies memories--just in time for the next election--with some frequently asked questions about electing the…

Teaching American Politics through Student Projects: Electoral Reform Issues and Political Change.

ERIC Educational Resources Information Center

Alper, Donald K.; Hogan, Eugene

1979-01-01

Describes two projects which involve college students in political science courses on American politics in doing research and giving class reports on proposals for reforming the electoral college and the electoral process. Findings indicate that students participating in the projects become more aware of political realities and learn how to use…

The Electoral College: A Teaching/Learning Design.

ERIC Educational Resources Information Center

Hamilton, Angela Blackston

This teacher's guide describes a course unit on the electoral college designed to teach eighth grade students about the election process for the President of the United States. The historical significance of the electoral college, its procedures, and its relevance to today's political system are discussed. Ten lesson plans with student objectives,…

Production of biodiesel from Coelastrella sp. microalgae

NASA Astrophysics Data System (ADS)

Mansur, Dieni; Fitriady, Muhammad Arifuddin; Susilaningsih, Dwi; Simanungkalit, Sabar Pangihutan

2017-11-01

Microalgae have a wide area of usage and one of them it can be used for biodiesel production. In biodiesel production, lipids containing triglyceride or free fatty acid are converted into methyl ester through trans/esterification reactions. Lipids from microalgae can be extracted by acetone and dimethyl carbonate using homogenizer. Esterification of the lipids was investigated using various catalysts and source of methyl group. Activity of homogeneous catalyst such as HCl and H2SO4 and heterogeneous catalysts such as montmorillonit K-10 and ledgestone was investigated. Moreover, methanol and dimethyl carbonate as source of methyl group were also studied. Among of catalysts with methanol as source of methyl group, it was found that yield of crude biodiesel derived from Choelestrella Sp. microalgae was high over H2SO4 catalyst. On the other hand, over H2SO4 catalyst using dimethyl carbonate as source of methyl group, yield of crude biodiesel significant increase. However, FAME composition of crude biodiesel was high over HCl catalyst.

piscope - A Python based software package for the analysis of volcanic SO2 emissions using UV SO2 cameras

NASA Astrophysics Data System (ADS)

Gliss, Jonas; Stebel, Kerstin; Kylling, Arve; Solvejg Dinger, Anna; Sihler, Holger; Sudbø, Aasmund

2017-04-01

UV SO2 cameras have become a common method for monitoring SO2 emission rates from volcanoes. Scattered solar UV radiation is measured in two wavelength windows, typically around 310 nm and 330 nm (distinct / weak SO2 absorption) using interference filters. The data analysis comprises the retrieval of plume background intensities (to calculate plume optical densities), the camera calibration (to convert optical densities into SO2 column densities) and the retrieval of gas velocities within the plume as well as the retrieval of plume distances. SO2 emission rates are then typically retrieved along a projected plume cross section, for instance a straight line perpendicular to the plume propagation direction. Today, for most of the required analysis steps, several alternatives exist due to ongoing developments and improvements related to the measurement technique. We present piscope, a cross platform, open source software toolbox for the analysis of UV SO2 camera data. The code is written in the Python programming language and emerged from the idea of a common analysis platform incorporating a selection of the most prevalent methods found in literature. piscope includes several routines for plume background retrievals, routines for cell and DOAS based camera calibration including two individual methods to identify the DOAS field of view (shape and position) within the camera images. Gas velocities can be retrieved either based on an optical flow analysis or using signal cross correlation. A correction for signal dilution (due to atmospheric scattering) can be performed based on topographic features in the images. The latter requires distance retrievals to the topographic features used for the correction. These distances can be retrieved automatically on a pixel base using intersections of individual pixel viewing directions with the local topography. The main features of piscope are presented based on dataset recorded at Mt. Etna, Italy in September 2015.

Making Green Cleaning Easy for Local School Boards

ERIC Educational Resources Information Center

Ashkin, Stephen

2012-01-01

Ten or even five years ago, it would have been a major undertaking for a school district to convert to a comprehensive green cleaning program. At that time there was little precedence and no "roadmaps" for doing so. Thus schools faced numerous challenges that included: (1) what defined a green cleaning product; (2) should a comprehensive program…

Intersystem Compatibility and Convertibility of Subject Vocabularies.

ERIC Educational Resources Information Center

Wall, E.; Barnes, J.

This is the fifth in a series of eight reports of a research study for the National Agricultural Library (NAL) on the effective utilization of bibliographic data bases in machine readable form. NAL desires ultimately to develop techniques of interacting with other data bases so that queries put to NAL may be answered with documents or document…

Estimating Surface NO2 and SO2 Mixing Ratios from Fast-Response Total Column Observations and Potential Application to Geostationary Missions

EPA Science Inventory

Total-column nitrogen dioxide (NO2) data collected by a ground-based sun-tracking spectrometer system 21 (Pandora) and an photolytic-converter-based in-situ instrument collocated at NASA’s Langley Research Center in 22 Hampton, Virginia were analyzed to study the relationship bet...

A Comparative Study of PDF Generation Methods: Measuring Loss of Fidelity When Converting Arabic and Persian MS Word Files to PDF

DTIC Science & Technology

2011-02-17

document objects, on one or more electronic document pages. These commands have their roots in typography , so, to understand the PDF Language, one...must have at least a rudimentary understanding of typography . Only a few of the typographic commands, called text showing operators, can hold strings

Method of producing molybdenum-99

DOEpatents

Pitcher, Eric John

2013-05-28

Method of producing molybdenum-99, comprising accelerating ions by means of an accelerator; directing the ions onto a metal target so as to generate neutrons having an energy of greater than 10 MeV; directing the neutrons through a converter material comprising techentium-99 to produce a mixture comprising molybdenum-99; and, chemically extracting the molybdenum-99 from the mixture.

A Multiple-Sessions Interactive Computer-Based Learning Tool for Ability Cultivation in Circuit Simulation

ERIC Educational Resources Information Center

Xu, Q.; Lai, L. L.; Tse, N. C. F.; Ichiyanagi, K.

2011-01-01

An interactive computer-based learning tool with multiple sessions is proposed in this paper, which teaches students to think and helps them recognize the merits and limitations of simulation tools so as to improve their practical abilities in electrical circuit simulation based on the case of a power converter with progressive problems. The…

Auxiliary quasi-resonant dc tank electrical power converter

DOEpatents

Peng, Fang Z.

2006-10-24

An auxiliary quasi-resonant dc tank (AQRDCT) power converter with fast current charging, voltage balancing (or charging), and voltage clamping circuits is provided for achieving soft-switched power conversion. The present invention is an improvement of the invention taught in U.S. Pat. No. 6,111,770, herein incorporated by reference. The present invention provides faster current charging to the resonant inductor, thus minimizing delay time of the pulse width modulation (PWM) due to the soft-switching process. The new AQRDCT converter includes three tank capacitors or power supplies to achieve the faster current charging and minimize the soft-switching time delay. The new AQRDCT converter further includes a voltage balancing circuit to charge and discharge the three tank capacitors so that additional isolated power supplies from the utility line are not needed. A voltage clamping circuit is also included for clamping voltage surge due to the reverse recovery of diodes.

Radiatively coupled thermionic and thermoelectric power system concept

NASA Technical Reports Server (NTRS)

Shimada, K.; Ewell, R.

1981-01-01

The study presented showed that the large power systems (about 100 kW) utilizing radiatively coupled thermionic or thermoelectric converters could be designed so that the power subsystem could be contained in a Space Shuttle bay as a part of an electrically propelled spacecraft. The radiatively coupled system requires a large number of individual converters since the transferred heat is smaller than with the conductively coupled system, but the advantages of the new system indicates merit for further study. The advantages are (1) good electrical isolation between converters and the heat source, (2) physical separation of converters from the heat source (making the system fabrication manageable), and (3) elimination of radiator heat pipes, which are required in an all-heat-pipe power system. In addition, the specific weight of the radiatively coupled power systems favorably compares with that of the all-heat-pipe systems.

Sox17 drives functional engraftment of endothelium converted from non-vascular cells

PubMed Central

Schachterle, William; Badwe, Chaitanya R.; Palikuqi, Brisa; Kunar, Balvir; Ginsberg, Michael; Lis, Raphael; Yokoyama, Masataka; Elemento, Olivier; Scandura, Joseph M.; Rafii, Shahin

2017-01-01

Transplanting vascular endothelial cells (ECs) to support metabolism and express regenerative paracrine factors is a strategy to treat vasculopathies and to promote tissue regeneration. However, transplantation strategies have been challenging to develop, because ECs are difficult to culture and little is known about how to direct them to stably integrate into vasculature. Here we show that only amniotic cells could convert to cells that maintain EC gene expression. Even so, these converted cells perform sub-optimally in transplantation studies. Constitutive Akt signalling increases expression of EC morphogenesis genes, including Sox17, shifts the genomic targeting of Fli1 to favour nearby Sox consensus sites and enhances the vascular function of converted cells. Enforced expression of Sox17 increases expression of morphogenesis genes and promotes integration of transplanted converted cells into injured vessels. Thus, Ets transcription factors specify non-vascular, amniotic cells to EC-like cells, whereas Sox17 expression is required to confer EC function. PMID:28091527

Representative misconduct, voter perceptions and accountability: Evidence from the 2009 House of Commons expenses scandal☆

PubMed Central

Vivyan, Nick; Wagner, Markus; Tarlov, Jessica

2012-01-01

This paper examines electoral accountability after the 2009–10 UK expenses scandal. Existing research shows that Members of Parliament (MPs) implicated in the scandal fared only marginally worse in the election than non-implicated colleagues. This lack of electoral accountability for misconduct could have arisen either because voters did not know about their representative's wrongdoing or because they chose not to electorally sanction them. We combine panel survey data with new measures of MP implication in the expenses scandal to test where electoral accountability failed. We find that MP implication influenced voter perceptions of wrongdoing more than expected. In contrast, constituents were only marginally less likely to vote for MPs who were implicated in the scandal. Electoral accountability may therefore be constrained even when information about representative misconduct is easily available and clearly influences voter perceptions. PMID:23576832

Precision envelope detector and linear rectifier circuitry

DOEpatents

Davis, Thomas J.

1980-01-01

Disclosed is a method and apparatus for the precise linear rectification and envelope detection of oscillatory signals. The signal is applied to a voltage-to-current converter which supplies current to a constant current sink. The connection between the converter and the sink is also applied through a diode and an output load resistor to a ground connection. The connection is also connected to ground through a second diode of opposite polarity from the diode in series with the load resistor. Very small amplitude voltage signals applied to the converter will cause a small change in the output current of the converter, and the difference between the output current and the constant current sink will be applied either directly to ground through the single diode, or across the output load resistor, dependent upon the polarity. Disclosed also is a full-wave rectifier utilizing constant current sinks and voltage-to-current converters. Additionally, disclosed is a combination of the voltage-to-current converters with differential integrated circuit preamplifiers to boost the initial signal amplitude, and with low pass filtering applied so as to obtain a video or signal envelope output.

Aura OMI Observations of Global SO2 and NO2 Pollution from 2005 to 2013

NASA Technical Reports Server (NTRS)

Krotkov, Nickolay; Li, Can; Lamsal, Lok; Celarier, Edward; Marchenko, Sergey; Swartz, William H.; Bucsela, Eric; Fioletov, Vitali; McLinden, Chris; Joiner, Joanna;

First-order irreversible thermodynamic approach to a simple energy converter

NASA Astrophysics Data System (ADS)

Arias-Hernandez, L. A.; Angulo-Brown, F.; Paez-Hernandez, R. T.

2008-01-01

Several authors have shown that dissipative thermal cycle models based on finite-time thermodynamics exhibit loop-shaped curves of power output versus efficiency, such as it occurs with actual dissipative thermal engines. Within the context of first-order irreversible thermodynamics (FOIT), in this work we show that for an energy converter consisting of two coupled fluxes it is also possible to find loop-shaped curves of both power output and the so-called ecological function versus efficiency. In a previous work Stucki [J. W. Stucki, Eur. J. Biochem. 109, 269 (1980)] used a FOIT approach to describe the modes of thermodynamic performance of oxidative phosphorylation involved in adenosine triphosphate (ATP) synthesis within mithochondrias. In that work the author did not use the mentioned loop-shaped curves and he proposed that oxidative phosphorylation operates in a steady state at both minimum entropy production and maximum efficiency simultaneously, by means of a conductance matching condition between extreme states of zero and infinite conductances, respectively. In the present work we show that all Stucki’s results about the oxidative phosphorylation energetics can be obtained without the so-called conductance matching condition. On the other hand, we also show that the minimum entropy production state implies both null power output and efficiency and therefore this state is not fulfilled by the oxidative phosphorylation performance. Our results suggest that actual efficiency values of oxidative phosphorylation performance are better described by a mode of operation consisting of the simultaneous maximization of both the so-called ecological function and the efficiency.

Measurement of sound absorption in the air. [data procesing

NASA Technical Reports Server (NTRS)

Meredith, R.; Badavi, F.; Becher, J.

1981-01-01

The large temperature gradient in each section of the resonance tube resulting from the liquid nitrogen coolant necessitated a design modification to the cooling system. A timer and four solenoid valves were installed so that the coolant flow can be reversed periodically. The hardware and software for controlling the analog to digital converter and conversion rate were completed, and the system is operational. A duty cycle control circit was implemented so that on the sixteenth conversion a relay shuts off the vibration exciter used to generate the sound wave. Thus the starting point of each decay curve is exactly known. This information is necessary for evaluating the g digital decay information. The data acquisition and digital decay evaluation programs are described.

Why phase errors affect the electron function more than amplitude errors.

PubMed

Lattman, Eaton; DeRosier, David

2008-03-01

If Fexp(ialpha) are the set of structure factors for a structure f, the amplitudes can be converted to those of an uncorrelated structure g (amplitude swapping) by multiplying each F by the positive number G/F. Correspondingly, the image f is convoluted with k, the Fourier transform of G/F; k has a large peak at the origin, so that f * k approximately f. For swapped phases, the image f is convoluted with l, the Fourier transform of exp(iDeltaalpha), where Deltaalpha, the phase difference between F and G, is a random variable; l does not have a large peak at the origin, so that f * l does not resemble f. The paper provides quantitative descriptions of these arguments.

Investigation into the role of sodium chloride deposited on oxide and metal substrates in the initiation of hot corrosion

NASA Technical Reports Server (NTRS)

Birks, N.

1983-01-01

Sodium chloride is deposited on the surface of alumina substrates and exposed to air containing 1% SO2 at temperatures between 500 C and 700 C. In all cases the sodium chloride was converted to sodium sulfate. The volatilization of sodium chloride from the original salt particles was responsible for the development of a uniform coating of sodium sulfate on the alumina substrate. At temperatures above 625 C, a liquid NaCl-Na2SO4 autectic was formed on the substrate. The mechanisms for these reactions are given. One of the main roles of NaCl in low temperature hot corrosion lies in enabling a corrosive liquid to form.

Methods to Control EMI Noises Produced in Power Converter Systems

NASA Astrophysics Data System (ADS)

Mutoh, Nobuyoshi; Ogata, Mitukatu

A new method to control EMI noises produced in power converters (rectifier and inverter) composed of IPMs (Intelligent Power Modules) is studied especially focusing on differential mode noises. The differential mode noises are occurred due to switching operations of the PWM control. As they are diffused into the ground through stray capacitors distributed between the ground and the power transmission lines and machine frames, differential mode noises should be confined and suppressed within the smallest area where power converters are laid out. It is impossible to control differential mode noises easily occurring diffusion by the conventional methods like filtering techniques. So, a new EMI noise control method using a multi-power circuit technique is proposed. The proposed method of the effectiveness has been verified through simulations and experiments.

Electoral reform and public policy outcomes in Thailand: the politics of the 30-Baht health scheme.

PubMed

Selway, Joel Sawat

2011-01-01

How do changes in electoral rules affect the nature of public policy outcomes? The current evidence supporting institutional theories that answer this question stems almost entirely from quantitative cross-country studies, the data of which contain very little within-unit variation. Indeed, while there are many country-level accounts of how changes in electoral rules affect such phenomena as the number of parties or voter turnout, there are few studies of how electoral reform affects public policy outcomes. This article contributes to this latter endeavor by providing a detailed analysis of electoral reform and the public policy process in Thailand through an examination of the 1997 electoral reforms. Specifically, the author examines four aspects of policy-making: policy formulation, policy platforms, policy content, and policy outcomes. The article finds that candidates in the pre-1997 era campaigned on broad, generic platforms; parties had no independent means of technical policy expertise; the government targeted health resources to narrow geographic areas; and health was underprovided in Thai society. Conversely, candidates in the post-1997 era relied more on a strong, detailed national health policy; parties created mechanisms to formulate health policy independently; the government allocated health resources broadly to the entire nation through the introduction of a universal health care system, and health outcomes improved. The author attributes these changes in the policy process to the 1997 electoral reform, which increased both constituency breadth (the proportion of the population to which politicians were accountable) and majoritarianism.

An investigation of reaction parameters on geochemical storage of non-pure CO2 streams in iron oxides-bearing formations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garcia, Susana; Liu, Q.; Bacon, Diana H.

2014-08-26

Hematite deposit that is the main FeIII-bearing mineral in sedimentary red beds was proposed as a potential host repository for converting CO2 into carbonate minerals such as siderite (FeCO3), when CO2–SO2 gas mixtures are co-injected. This work investigated CO2 mineral trapping using hematite and sensitivity of the reactive systems to different parameters, including particle size, gas composition, temperature, pressure, and solid-to-liquid ratio. Experimental and modelling studies of hydrothermal experiments were conducted, which emulated a CO2 sequestration scenario by injecting CO2-SO2 gas streams into a NaCl-NaOH brine hosted in iron oxide-containing aquifer. This study provides novel information on the mineralogical changesmore » and fluid chemistry derived from the co-injection of CO2-SO2 gas mixtures in hematite deposit. It can be concluded that the amount of siderite precipitate depends primarily on the SO2 content of the gas stream. Increasing SO2 content in the system could promote the reduction of Fe3+ from the hematite sample to Fe2+, which will be further available for its precipitation as siderite. Moreover, siderite precipitation is enhanced at low temperatures and high pressures. The influence of the solid to liquid ratio on the overall carbonation reaction suggests that the conversion increases if the system becomes more diluted.« less

BONE MASS BY QUANTITATIVE ULTRASOUND OF FINGER PHALANGES IN YOUNG KARATE PRACTITIONERS

PubMed Central

Barbeta, Camila Justino de Oliveira; Gonçalves, Ezequiel Moreira; Ribeiro, Keila Donassolo Santos; Ribeiro, Roberto; Roman, Everton Paulo; Guerra-Júnior, Gil

2017-01-01

ABSTRACT Objective: To evaluate bone mass by quantitative ultrasound of the phalanges in young karate practitioners compared to a control group. Methods: Sample composed of 162 karate practitioners (52 females) and 326 healthy controls (110 females) aged 6 to 16 years old, in Western Paraná (Southern Brazil). Weight, height, BMI, amplitude-dependent speed of sound (AD-SoS) and bone transmission time (BTT) were evaluated. BMI, AD-SoS and BTT values were converted to Z scores. Mann-Whitney, chi-square or Fisher Exact tests and multiple linear regression were applied, with significance level set at p≤0.05. Results: Both genders showed higher values of BTT as Z scores when compared to control group. Females from the control group had higher AD-SoS values (m/s and Z score) compared to female karate practitioners. When relative and absolute frequencies were assessed according to BTT Z score in both groups, male karate practitioners’ bone mass was shown to be adequate more frequently. In female practitioners, age and weight were independent predictors of AD-SoS (R2=0.42) and BTT (R2=0.45), respectively. Among male karate practitioners, age was related to 26% of AD-SoS variances and height was responsible for 36% of BTT variances. Conclusions: Children and adolescents who practice karate were shown to have more bone mass in comparison to the control group, regardless of gender. BTT was more sensitive for this evaluation. PMID:28977128

Ferric iron in sediments as a novel CO2 mineral trap: CO 2-SO2 reaction with hematite

USGS Publications Warehouse

Palandri, J.L.; Rosenbauer, R.J.; Kharaka, Y.K.

2005-01-01

Thermodynamic simulations of reactions among SO2-bearing CO 2-dominated gas, water and mineral phases predict that Fe III in sediments should be converted almost entirely to dissolved FeII and siderite (FeCO3), and that SO2 should simultaneously be oxidized to dissolved sulfate. The reactions are however, subject to kinetic constraints which may result in deviation from equilibrium and the precipitation of other metastable mineral phases. To test the prediction, a laboratory experiment was carried out in a well stirred hydrothermal reactor at 150??C and 300 bar with hematite, 1.0 m NaCl, 0.5 m NaOH, SO2 in quantity sufficient to reduce much of the iron, and excess CO2. The experiment produced stable siderite and metastable pyrite and elemental S. Changes in total dissolved Fe are consistent with nucleation of pyrite at ???17 h, and nucleation of siderite at ???600 h. Dissolution features present on elemental S at the conclusion of the experiment suggest nucleation early in the experiment. The experiment did not reach equilibrium after ???1400 h, as indicated by coexistence of hematite with metastable pyrite and elemental sulfur. However, the results confirm that FeIII can be used to trap CO2 in siderite if partly oxidized S, as SO2, is present to reduce the Fe with CO2 in the gas phase. ?? 2005 Elsevier Ltd. All rights reserved.

Templated Growth of Carbon Nanotubes

NASA Technical Reports Server (NTRS)

Siochik Emilie J. (Inventor)

2007-01-01

A method of growing carbon nanotubes uses a synthesized mesoporous si lica template with approximately cylindrical pores being formed there in. The surfaces of the pores are coated with a carbon nanotube precu rsor, and the template with the surfaces of the pores so-coated is th en heated until the carbon nanotube precursor in each pore is convert ed to a carbon nanotube.

Encoder: A Connectionist Model of How Learning to Visually Encode Fixated Text Images Improves Reading Fluency

ERIC Educational Resources Information Center

Martin, Gale L.

2004-01-01

This article proposes that visual encoding learning improves reading fluency by widening the span over which letters are recognized from a fixated text image so that fewer fixations are needed to cover a text line. Encoder is a connectionist model that learns to convert images like the fixated text images human readers encode into the…

Converting among log scaling methods : Scriber, International, and Doyle versus cubic

Treesearch

Henry Spelter

2004-01-01

Sawlogs in the United States, whether scaled on the ground or cruised on the stump, have traditionally been measured in terms of their lumber yield. The three commonly used measurement rules generally underestimate true recoveries. Moreover, they do so inconsistently, complicating the comparisons of volumes obtained by different board foot rules as well as by the cubic...

40 CFR 52.2500 - Best available retrofit technology requirements for the Intalco Aluminum Corporation (Intalco...

Code of Federal Regulations, 2014 CFR

2014-07-01

... = (carbon consumption ratio) × (% sulfur in baked anodes/100) × (% sulfur converted to SO2/100) × (2 pounds... ratio is the calendar month average of tons of baked anodes consumed per ton of aluminum produced as determined using the baked anode consumption and production records required in paragraph (e)(2) of this...

Alternative Fuels Data Center: Truck Stop Electrification for Heavy-Duty

Science.gov Websites

-board equipment so trucks can plug into electrical outlets at the truck stop. To use dual-system electrification, trucks must be equipped with AC equipment or an inverter to convert 120-volt power, electrical equipment, and hardware to plug in to the electrical outlet. Necessary electrical equipment might include an

Superconductor Particles As The Working Media Of A Heat Engine

NASA Astrophysics Data System (ADS)

Keefe, Peter D.

2011-12-01

A heat engine is presented in which the working media comprises a multiplicity of mutually isolated particles of Type I superconductor which are selectively processed through H-T phase space so as to convert a heat influx from a high temperature heat reservoir into a useful work output, wherein no heat is rejected to a low temperature heat reservoir.

Some wood of Hawaii... properties and uses of 16 commercial species

Treesearch

Roger G. Skolmen

1974-01-01

Koa is Hawaii's finest native timber tree. Unfortunately, it grows best in areas that can be converted into good grazing land, and most of the best koa forests have been cleared to develop pasture. Consequently, not much koa is left. Koa seedlings are also palatable to grazing animals, so that the number of young, vigorous koa trees is small.

Analysis of aircraft spectrometer data with logarithmic residuals

NASA Technical Reports Server (NTRS)

Green, A. A.; Craig, M. D.

1985-01-01

Spectra from airborne systems must be analyzed in terms of their mineral-related absorption features. Methods for removing backgrounds and extracting these features one at a time from reflectance spectra are discussed. Methods for converting radiance spectra into a form similar to reflectance spectra so that the feature extraction procedures can be implemented on aircraft spectrometer data are also discussed.

Composition and method for brazing graphite to graphite

DOEpatents

Taylor, Albert J.; Dykes, Norman L.

1984-01-01

The present invention is directed to a brazing material for joining graphite structures that can be used at temperatures up to about 2800.degree. C. The brazing material formed of a paste-like composition of hafnium carbide and uranium oxide with a thermosetting resin. The uranium oxide is converted to uranium dicarbide during the brazing operation and then the hafnium carbide and uranium dicarbide form a liquid phase at a temperature about 2600.degree. C. with the uranium diffusing and vaporizing from the joint area as the temperature is increased to about 2800.degree. C. so as to provide a brazed joint consisting essentially of hafnium carbide. This brazing temperature for hafnium carbide is considerably less than the eutectic temperature of hafnium carbide of about 3150.degree. C. The brazing composition also incorporates the thermosetting resin so that during the brazing operation the graphite structures may be temporarily bonded together by thermosetting the resin so that machining of the structures to final dimensions may be completed prior to the completion of the brazing operation. The resulting brazed joint is chemically and thermally compatible with the graphite structures joined thereby and also provides a joint of sufficient integrity so as to at least correspond with the strength and other properties of the graphite.

Civil Military Operations In Ecuador

DTIC Science & Technology

2003-03-01

3455 This process of "re-democratization" meant more than the establishment of simple " electoral democracies඀. The return to democracy meant, for...representation, uncertain electoral outcomes, control of the state by political elected officials, and military subordination to the authority of elected...Abadalá Bucarám won the presidential elections with 54% of the electoral vote. Michael L. Conniff describes the elite reaction to his election

Determination of the δ34S of low-concentration sulfate in water; RSIL lab code 1949

USGS Publications Warehouse

Revesz, Kinga; Qi, Haiping; Coplen, Tyler B.

2006-01-01

The purpose of the Reston Stable Isotope Laboratory (RSIL) lab code 1949 is to determine the δ(34S/32S), abbreviated as δ34S, of dissolved sulfate having a concentration less than 20 milligrams per liter. Dissolved sulfate is collected on an anion-exchange resin in the field, eluted in the laboratory with 3 M KCl, and precipitated with BaCl2 at pH 3 to 4 as BaSO4. The precipitated BaSO4 is filtered and dried before introduction into an elemental analyzer (EA) Carlo Erba NC 2500. The EA is used to convert sulfur in a BaSO4 solid sample into SO2 gas, and the EA is connected to a continuous flow isotope-ratio mass spectrometer (CF-IRMS), which determines differences in the isotope-amount ratios of stable sulfur isotopes (34S/32S) of the product SO2 gas. The combustion is quantitative; no isotopic fractionation is involved. Samples are placed in a tin capsule and loaded into the Costech Zero Blank Autosampler of the EA. Under computer control, samples are dropped into a heated reaction tube that combines the oxidation and reduction reactions. The combustion takes place in a helium atmosphere containing an excess of oxygen gas at the oxidation zone at the top of the reaction tube. Combustion products are transported by a helium carrier through the reduction zone at the bottom of the reaction tube to remove excess oxygen and through a separate drying tube to remove any water. The gas-phase products, mainly CO2, N2, and SO2, are separated by a gas chromatograph. The gas is then introduced into the isotope-ratio mass spectrometer (IRMS) through a Finnigan MAT (now Thermo Scientific) ConFlo II interface, which is also used to inject SO2 reference gas and helium for sample dilution. The IRMS is a Thermo Scientific Delta V Plus CF-IRMS. It has a universal triple collector with two wide cups and a narrow cup in the middle. It is capable of measuring mass/charge (m/z) 64 and 66 simultaneously. The ion beams from SO2 are as follows: m/z 64 = SO2 = 32S16O16O; m/z 66 = SO2 = 34S16O16O primarily.

Investigation of a generator system for generating electrical power, to supply directly to the public network, using a windmill

NASA Technical Reports Server (NTRS)

Tromp, C.

1979-01-01

A windpowered generator system is described which uses a windmill to convert mechanical energy to electrical energy for a three phase (network) voltage of constant amplitude and frequency. The generator system controls the windmill by the number of revolutions so that the power drawn from the wind for a given wind velocity is maximum. A generator revolution which is proportional to wind velocity is achieved. The stator of the generator is linked directly to the network and a feed converter at the rotor takes care of constant voltage and frequency at the stator.

Implementation of high-resolution time-to-digital converter in 8-bit microcontrollers.

PubMed

Bengtsson, Lars E

2012-04-01

This paper will demonstrate how a time-to-digital converter (TDC) with sub-nanosecond resolution can be implemented into an 8-bit microcontroller using so called "direct" methods. This means that a TDC is created using only five bidirectional digital input-output-pins of a microcontroller and a few passive components (two resistors, a capacitor, and a diode). We will demonstrate how a TDC for the range 1-10 μs is implemented with 0.17 ns resolution. This work will also show how to linearize the output by combining look-up tables and interpolation. © 2012 American Institute of Physics

Electromagnetic wave energy converter

NASA Technical Reports Server (NTRS)

Bailey, R. L. (Inventor)

1973-01-01

Electromagnetic wave energy is converted into electric power with an array of mutually insulated electromagnetic wave absorber elements each responsive to an electric field component of the wave as it impinges thereon. Each element includes a portion tapered in the direction of wave propagation to provide a relatively wideband response spectrum. Each element includes an output for deriving a voltage replica of the electric field variations intercepted by it. Adjacent elements are positioned relative to each other so that an electric field subsists between adjacent elements in response to the impinging wave. The electric field results in a voltage difference between adjacent elements that is fed to a rectifier to derive dc output power.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chinthavali, Madhu Sudhan; Onar, Omer C; Campbell, Steven L

Integrated charger topologies that have been researched so far are with the dc-dc converters and the charging functionality usually have no isolation in the system. Isolation is an important feature that is required for user interface systems that have grid connections and therefore is a major limitation that needs to be addressed along with the integrated functionality. This study features a unique way of combining the wired and wireless charging functionalities with vehicle side boost converter integration and maintaining the isolation to provide the best solution to the plug-in electric vehicle (PEV) users. The new performance of the proposed architecturemore » is presented for wired and wireless charging options at different power levels.« less

Electron-induced chemistry in microhydrated sulfuric acid clusters

NASA Astrophysics Data System (ADS)

Lengyel, Jozef; Pysanenko, Andriy; Fárník, Michal

2017-11-01

We investigate the mixed sulfuric acid-water clusters in a molecular beam experiment with electron attachment and negative ion mass spectrometry and complement the experiment by density functional theory (DFT) calculations. The microhydration of (H2SO4)m(H2O)n clusters is controlled by the expansion conditions, and the electron attachment yields the main cluster ion series (H2SO4)m(H2O)nHSO4- and (H2O)nH2SO4-. The mass spectra provide an experimental evidence for the onset of the ionic dissociation of sulfuric acid and ion-pair (HSO4- ṡ ṡ ṡ H3O+) formation in the neutral H2SO4(H2O)n clusters with n ≥ 5 water molecules, in excellent agreement with the theoretical predictions. In the clusters with two sulfuric acid molecules (H2SO4)2(H2O)n this process starts as early as n ≥ 2 water molecules. The (H2SO4)m(H2O)nHSO4- clusters are formed after the dissociative electron attachment to the clusters containing the (HSO4- ṡ ṡ ṡ H3O+) ion-pair structure, which leads to the electron recombination with the H3O+ moiety generating H2O molecule and the H-atom dissociation from the cluster. The (H2O)nH2SO4- cluster ions point to an efficient caging of the H atom by the surrounding water molecules. The electron-energy dependencies exhibit an efficient electron attachment at low electron energies below 3 eV, and no resonances above this energy, for all the measured mass peaks. This shows that in the atmospheric chemistry only the low-energy electrons can be efficiently captured by the sulfuric acid-water clusters and converted into the negative ions. Possible atmospheric consequences of the acidic dissociation in the clusters and the electron attachment to the sulfuric acid-water aerosols are discussed.

Determination of the δ34S of Total Sulfur in Solids: RSIL Lab Code 1800

USGS Publications Warehouse

Revesz, Kinga; Coplen, Tyler B.

2006-01-01

The purpose of Reston Stable Isotope Laboratory Lab (RSIL) Code 1800 is to determine the δ(34S/32S), abbreviated as δ34S, of total sulfur in a solid sample. A Carlo Erba NC 2500 elemental analyzer (EA) is used to convert total sulfur in a solid sample into SO2 gas. The EA is connected to a continuous flow isotope-ratio mass spectrometer (CF-IRMS), which determines the relative difference in stable sulfur isotope-amount ratio (34S/32S) of the product SO2 gas. The combustion is quantitative; no isotopic fractionation is involved. Samples are placed in tin capsules and loaded into a Costech Zero-Blank Autosampler on the EA. Under computer control, samples are dropped into a heated tube reaction tube that combines both the oxidation and the reduction reactions. The combustion takes place in a He atmosphere that contains an excess of oxygen gas at the oxidation zone at the top of the reaction tube. Combustion products are transported by a He carrier through the reduction zone at the bottom of the reaction tube to remove excess oxygen and through a separate drying tube to remove any water. The gas-phase products, mainly CO2, N2, and SO2, are separated by a gas chromatograph (GC). The gas is then introduced into the isotope-ratio mass spectrometer (IRMS) through a Thermo-Finnigan ConFlo II interface, which also is used to inject SO2 reference gas and He for sample dilution. The IRMS is a Thermo-Finnigan DeltaPlus CF-IRMS. It has a universal triple collector with two wide cups and a narrow cup in the middle. It is capable of measuring mass/charge (m/z) 64 and 66 simultaneously. The ion beams from SO2 are as follows: m/z 64 = SO2 = 32S16O16O; and m/z 66 = SO2 = 34S16O16O primarily.

Compilation of a Global Emission Inventory from 1980 to 2000 for Global Model Simulations of the Long-term Trend of Tropospheric Aerosols

NASA Technical Reports Server (NTRS)

Diehl, T. L.; Mian, Chin; Bond, T. C.; Carn, S. A.; Duncan, B. N.; Krotkov, N. A.; Streets, D. G.

2007-01-01

The approach to create a comprehensive emission inventory for the time period 1980 to 2000 is described in this paper. We have recently compiled an emission database, which we will use for a 21 year simulation of tropospheric aerosols with the GOCART model. Particular attention was paid to the time-dependent SO2, black carbon and organic carbon aerosol emissions. For the emission of SO2 from sporadically erupting volcanoes, we assembled emission data from the Global Volcanism Program of the Smithsonian Institution, using the VEI to derive the volcanic cloud height and the SO2 amount, and amended this dataset by the SO2 emission data from the TOMS instrument when available. 3-dimensional aircraft emission data was obtained for a number of years from the AEAP project, converted from burned fuel to SO2 and interpolated to each year, taking the sparsity of the flight patterns into account. Other anthopogenic SO2 emissions are based on gridded emissions from the EDGAR 2000 database (excluding sources from aircraft, biomass burning and international ship traffic), which were scaled to individual years with country/regional based emission inventories. Gridded SO2 emissions from international ship traffic for 2000 and the scaling factors for other years are from [Eyring et al., 2005]. We used gridded anthropogenic black and organic carbon emissions for 1996 [Bond et al., 2005], again excluding aircraft, biomass burning and ship sources. These emissions were scaled with regional based emission inventories from 1980 to 2000 to derive gridded emissions for each year. The biomass burning emissions are based on a climatology, which is scaled with regional scaling factors derived from the TOMS aerosol index and the AVHRR/ATSR fire counts to each year [Duncan et al., 2003]. Details on the integration of the information from the various sources will be provided and the distribution patterns and total emissions in the final product will be discussed.

Compilation of a Global Emission Inventory from 1980 to 2000 for Global Model Simulations of the Long-term Trend of Tropospheric Aerosols

NASA Technical Reports Server (NTRS)

Diehl, Thomas L.; Chin, Mian; Bond, Tami C.; Carn, SImon A.; Duncan, Bryan N.; Krotkov, Nickolay A.; Streets, David G.

2006-01-01

The approach to create a comprehensive emission inventory for the time period 1980 to 2000 is described in this paper. We have recently compiled an emission database, which we will use for a 21 year simulation of tropospheric aerosols with the GOCART model. Particular attention was paid to the time-dependent SO2, black carbon and organic carbon aerosol emissions. For the emission of SO2 from sporadically erupting volcanoes, we assembled emission data from the Global Volcanism Program of the Smithsonian Institution, using the VEI to derive the volcanic cloud height and the SO2 amount, and amended this dataset by the SO2 emission data from the TOMS instrument when available. 3-dimensional aircraft emission data was obtained for a number of years from the AEAP project, converted from burned fuel to SO2 and interpolated to each year, taking the sparsity of the flight patterns into account. Other anthropogenic SO2 emissions are based on gridded emissions from the EDGAR 2000 database (excluding sources from aircraft, biomass burning and international ship traffic), which were scaled to individual years with country/regional based emission inventories. Gridded SO2 emissions from international ship traffic for 2000 and the scaling factors for other years are from [Eyring et al., 2005]. We used gridded anthropogenic black and organic carbon emissions for 1996 [Bond et al., 2005], again excluding aircraft, biomass burning and ship sources. These emissions were scaled with regional based emission inventories from 1980 to 2000 to derive gridded emissions for each year. The biomass burning emissions are based on a climatology, which is scaled with regional scaling factors derived from the TOMS aerosol index and the AVHRR/ASTR fire counts to each year [Duncan et al., 2003]. Details on the integration of the information from the various sources will be provided and the distribution patterns and total emissions in the final product will be discussed.

Of Ballots and Bullets: Explaining Civilian Control of the Military in Turkey, 2002-2011

DTIC Science & Technology

2014-09-01

had failed? Using the theory of electoral competition, this dissertation demonstrates the link between elections and policy making, and how together...AKP succeed where other political parties had failed? Using the theory of electoral competition, this dissertation demonstrates the link between...between the AKP and the TSK are informed by a variety of theories , electoral competition and the incentive structure created by elections best explains

Forensic analysis of Venezuelan elections during the Chávez presidency.

PubMed

Jiménez, Raúl; Hidalgo, Manuel

2014-01-01

Hugo Chávez dominated the Venezuelan electoral landscape since his first presidential victory in 1998 until his death in 2013. Nobody doubts that he always received considerable voter support in the numerous elections held during his mandate. However, the integrity of the electoral system has come into question since the 2004 Presidential Recall Referendum. From then on, different sectors of society have systematically alleged electoral irregularities or biases in favor of the incumbent party. We have carried out a thorough forensic analysis of the national-level Venezuelan electoral processes held during the 1998-2012 period to assess these complaints. The second-digit Benford's law and two statistical models of vote distributions, recently introduced in the literature, are reviewed and used in our case study. In addition, we discuss a new method to detect irregular variations in the electoral roll. The outputs obtained from these election forensic tools are examined taking into account the substantive context of the elections and referenda under study. Thus, we reach two main conclusions. Firstly, all the tools uncover anomalous statistical patterns, which are consistent with election fraud from 2004 onwards. Although our results are not a concluding proof of fraud, they signal the Recall Referendum as a turning point in the integrity of the Venezuelan elections. Secondly, our analysis calls into question the reliability of the electoral register since 2004. In particular, we found irregular variations in the electoral roll that were decisive in winning the 50% majority in the 2004 Referendum and in the 2012 Presidential Elections.

Forensic Analysis of Venezuelan Elections during the Chávez Presidency

PubMed Central

Jiménez, Raúl; Hidalgo, Manuel

2014-01-01

Hugo Chávez dominated the Venezuelan electoral landscape since his first presidential victory in 1998 until his death in 2013. Nobody doubts that he always received considerable voter support in the numerous elections held during his mandate. However, the integrity of the electoral system has come into question since the 2004 Presidential Recall Referendum. From then on, different sectors of society have systematically alleged electoral irregularities or biases in favor of the incumbent party. We have carried out a thorough forensic analysis of the national-level Venezuelan electoral processes held during the 1998–2012 period to assess these complaints. The second-digit Benford's law and two statistical models of vote distributions, recently introduced in the literature, are reviewed and used in our case study. In addition, we discuss a new method to detect irregular variations in the electoral roll. The outputs obtained from these election forensic tools are examined taking into account the substantive context of the elections and referenda under study. Thus, we reach two main conclusions. Firstly, all the tools uncover anomalous statistical patterns, which are consistent with election fraud from 2004 onwards. Although our results are not a concluding proof of fraud, they signal the Recall Referendum as a turning point in the integrity of the Venezuelan elections. Secondly, our analysis calls into question the reliability of the electoral register since 2004. In particular, we found irregular variations in the electoral roll that were decisive in winning the 50% majority in the 2004 Referendum and in the 2012 Presidential Elections. PMID:24971462

Using evidence to strengthen accountability for health financing in Sierra Leone.

PubMed

Lebbie, Sowo A; Le Voir, Rosanna; Tom-Kargbo, Joanna; Yilla, Mohamed Drissa; Kamara, Abu Bakarr; Nam, Sara L

2016-12-01

In 2012, the government of Sierra Leone cut the national budget allocation to the health sector. Civil society organizations planned a nationwide health budget advocacy campaign, coinciding with the 2012 general elections, to hold future leaders to account on financing for women's and children's health. As part of the campaign, Evidence for Action produced district health budget tracking scorecards. The scorecards presented Ministry of Finance data on the allocation and disbursement of health funds in each district. The data were communicated using simple, non-technical language so that citizens could understand the key messages and take action. A total of 5600 scorecards were shared at district electoral forums attended by political candidates, community members, and health activists. Since the election, the proportion of the total government budget allocated to health increased from 7.4% in 2012 to 11.2% in 2014. However, transforming politicians' commitments and pledges into implementation has been challenging, confirming that accountability is a long-term process. Copyright © 2016 International Federation of Gynecology and Obstetrics. Published by Elsevier Ireland Ltd. All rights reserved.

Becoming independent: political participation and youth transitions in the Scottish referendum.

PubMed

Breeze, Maddie; Gorringe, Hugo; Jamieson, Lynn; Rosie, Michael

2017-12-01

Sociological debates on youth engagement with electoral politics play out against a backdrop of supposed 'decline' in civic participation (e.g. Putnam , Norris, ), in turn contextualized by theories of individualization in 'late' or 'reflexive' modernity (Beck, Giddens). However, the enfranchisement of 16 and 17 year olds in the 2014 Scottish Independence Referendum catalysed remarkably high levels of voter turnout among this youngest group, and was accompanied by apparently ongoing political engagement. We explored this engagement among a strategic sample of young 'Yes' voters, in the immediate aftermath of this exceptional political event. Analysis of qualitative interview data generated an unanticipated finding; that interviewees narrated their political engagement biographically, articulated their referendum participation reflexively, and located their new political ideas, allegiances and actions in the context of their own transitions to 'independent' adulthood. This inspired us to rethink young people's political engagement in relation to youth transitions. Doing so enables a synthesis of divergent strands in the sociology of youth, and offers new insights into the combinations of 'personal' agentic and 'political' structural factors involved in young people's politicization. © London School of Economics and Political Science 2017.

DNA Microarray Data Analysis: A Novel Biclustering Algorithm Approach

NASA Astrophysics Data System (ADS)

Tchagang, Alain B.; Tewfik, Ahmed H.

2006-12-01

Biclustering algorithms refer to a distinct class of clustering algorithms that perform simultaneous row-column clustering. Biclustering problems arise in DNA microarray data analysis, collaborative filtering, market research, information retrieval, text mining, electoral trends, exchange analysis, and so forth. When dealing with DNA microarray experimental data for example, the goal of biclustering algorithms is to find submatrices, that is, subgroups of genes and subgroups of conditions, where the genes exhibit highly correlated activities for every condition. In this study, we develop novel biclustering algorithms using basic linear algebra and arithmetic tools. The proposed biclustering algorithms can be used to search for all biclusters with constant values, biclusters with constant values on rows, biclusters with constant values on columns, and biclusters with coherent values from a set of data in a timely manner and without solving any optimization problem. We also show how one of the proposed biclustering algorithms can be adapted to identify biclusters with coherent evolution. The algorithms developed in this study discover all valid biclusters of each type, while almost all previous biclustering approaches will miss some.

Determination of the δ34S of sulfate in water; RSIL lab code 1951

USGS Publications Warehouse

Revesz, Kinga; Qi, Haiping; Coplen, Tyler B.

2006-01-01

The purpose of the Reston Stable Isotope Laboratory (RSIL) lab code 1951 is to determine the δ(34S/32S), abbreviated as δ34S, of dissolved sulfate. Dissolved sulfate is collected in the field and precipitated with BaCl2 at pH 3 to 4 as BaSO4 in the laboratory. However, the dissolved organic sulfur (DOS) is oxidized to SO2, and the carbonate is acidified to CO2. Both are degassed from the water sample before the sulfate is precipitated. The precipitated BaSO4 is filtered and dried before introduction into an elemental analyzer (EA) Carlo Erba NC 2500. The EA is used to convert sulfur in a BaSO4 solid sample into SO2 gas, and the EA is connected to a continuous flow isotope-ratio mass spectrometer (CF-IRMS), which determines the differences in the isotope-amount ratios of stable sulfur isotopes (34S/32S) of the product SO2 gas. The combustion is quantitative; no isotopic fractionation is involved. Samples are placed in a tin capsule and loaded into the Costech Zero Blank Autosampler of the EA. Under computer control, samples are dropped into a heated tube reaction tube that combines the oxidation and reduction reactions. The combustion takes place in a helium atmosphere containing an excess of oxygen gas at the oxidation zone at the top of the reaction tube. Combustion products are transported by a helium carrier through the reduction zone at the bottom of the reaction tube to remove excess oxygen and through a separate drying tube to remove any water. The gas-phase products, mainly CO2, N2, and SO2, are separated by a gas chromatograph. The gas is then introduced into the isotope-ratio mass spectrometer (IRMS) through a Finnigan MAT (now Thermo Scientific) ConFlo II interface, which also is used to inject SO2 reference gas and helium for sample dilution. The IRMS is a Thermo Scientific Delta V Plus CF-IRMS. It has a universal triple collector with two wide cups and a narrow cup in the middle. It is capable of measuring mass/charge (m/z) 64 and 66 simultaneously. The ion beams from SO2 are as follows: m/z 64 = SO2 = 32S16O16O; m/z 66 = SO2 = 34S16O16O primarily.

Hydrothermal syntheses and anion-induced structural transformation of three Cadmium phosphonates

NASA Astrophysics Data System (ADS)

Hu, Han; Zhai, Fupeng; Liu, Xiaofeng; Ling, Yun; Chen, Zhenxia; Zhou, Yaming

2018-05-01

Three cadmium phosphonate coordinated polymers, namely as [Cd5(ptz)3(SO4)2(5H2O)]·6H2O (Cdptz-1), [Cd3(ptz)2(Cl)2(4H2O)]·2H2O (Cdptz-2) and [Cd4(ptz)2(SO4)(Cl)(OH)H2O]·H2O (Cdptz-3) have been hydrothermally synthesized using 4-(1,2,4-triazol-4-yl)phenylphosphonic acid (H2ptz) as ligand. Single crystal X-ray analyses revealed Cdptz-2 as layered structure and Cdptz-1,3 as pillar-layered structures with Cl- or SO42- as bridging anions. Due to the weak bonding between metal and anions, Cdptz-1 and 2 can reversibly convert into each other by simple immersing in the corresponding solution at room temperature. While the transformations between Cdptz-1,2 and Cdptz-3 can only happen under hydrothermal condition. The causes for the transformation involve the metal-ligand bond breaking/formation, replacement of anions and enhancement/decrement of the network dimensionality.

Compensated count-rate circuit for radiation survey meter

DOEpatents

Todd, Richard A.

1981-01-01

A count-rate compensating circuit is provided which may be used in a portable Geiger-Mueller (G-M) survey meter to ideally compensate for counting loss errors in the G-M tube detector. In a G-M survey meter, wherein the pulse rate from the G-M tube is converted into a pulse rate current applied to a current meter calibrated to indicate dose rate, the compensated circuit generates and controls a reference voltage in response to the rate of pulses from the detector. This reference voltage is gated to the current-generating circuit at a rate identical to the rate of pulses coming from the detector so that the current flowing through the meter is varied in accordance with both the frequency and amplitude of the reference voltage pulses applied thereto so that the count rate is compensated ideally to indicate a true count rate within 1% up to a 50% duty cycle for the detector. A positive feedback circuit is used to control the reference voltage so that the meter output tracks true count rate indicative of the radiation dose rate.

Compensated count-rate circuit for radiation survey meter

DOEpatents

Todd, R.A.

1980-05-12

A count-rate compensating circuit is provided which may be used in a portable Geiger-Mueller (G-M) survey meter to ideally compensate for couting loss errors in the G-M tube detector. In a G-M survey meter, wherein the pulse rate from the G-M tube is converted into a pulse rate current applied to a current meter calibrated to indicate dose rate, the compensation circuit generates and controls a reference voltage in response to the rate of pulses from the detector. This reference voltage is gated to the current-generating circuit at a rate identical to the rate of pulses coming from the detector so that the current flowing through the meter is varied in accordance with both the frequency and amplitude of the reference voltage pulses applied thereto so that the count rate is compensated ideally to indicate a true count rate within 1% up to a 50% duty cycle for the detector. A positive feedback circuit is used to control the reference voltage so that the meter output tracks true count rate indicative of the radiation dose rate.

A note on the chemistry of seawater in the range 350°-500°C

USGS Publications Warehouse

Bischoff, James L.; Rosenbauer, Robert J.

1983-01-01

The chemistry of seawater at conditions of 350° to 500°C, 220 to 1000 bars (22 to 100 MPa) is controlled by reactions involving magnesium hydroxide sulfate (MHSH) and anhydrite. During progressive heating from 350° to 500°C at 1000 bars (100 MPa), MHSH with a  ratio of 1.25 is formed via precipitation from solution and via reaction of solution with pre-existing anhydrite. During adiabatic expansion the MHSH extracts additional SO4 from seawater and converts to a stoichiometry in which . These reactions control and greatly change the concentrations of Ca, Mg, SO4 in solution and produce significant ionizable hydrogen, attaining 11.7 mmoles kg−1 at maximum conditions.

Method and Apparatus for Improving the Resolution of Digitally Sampled Analog Data

NASA Technical Reports Server (NTRS)

Liaghati, Amir L. (Inventor)

2017-01-01

A system and method is described for converting an analog signal into a digital signal. The gain and offset of an ADC is dynamically adjusted so that the N-bits of input data are assigned to a narrower channel instead of the entire input range of the ADC. This provides greater resolution in the range of interest without generating longer digital data strings.

46 CFR 32.52-5 - Bilge piping for pump rooms and adjacent cofferdams on tank vessels constructed or converted on...

Code of Federal Regulations, 2013 CFR

2013-10-01

... as complying with this provision, or alternatively, the pump controls shall be arranged so that they... 46 Shipping 1 2013-10-01 2013-10-01 false Bilge piping for pump rooms and adjacent cofferdams on... REQUIREMENTS Bilge Systems § 32.52-5 Bilge piping for pump rooms and adjacent cofferdams on tank vessels...

46 CFR 32.52-5 - Bilge piping for pump rooms and adjacent cofferdams on tank vessels constructed or converted on...

Code of Federal Regulations, 2014 CFR

2014-10-01

... as complying with this provision, or alternatively, the pump controls shall be arranged so that they... 46 Shipping 1 2014-10-01 2014-10-01 false Bilge piping for pump rooms and adjacent cofferdams on... REQUIREMENTS Bilge Systems § 32.52-5 Bilge piping for pump rooms and adjacent cofferdams on tank vessels...

46 CFR 32.52-5 - Bilge piping for pump rooms and adjacent cofferdams on tank vessels constructed or converted on...

Code of Federal Regulations, 2011 CFR

2011-10-01

... as complying with this provision, or alternatively, the pump controls shall be arranged so that they... 46 Shipping 1 2011-10-01 2011-10-01 false Bilge piping for pump rooms and adjacent cofferdams on... REQUIREMENTS Bilge Systems § 32.52-5 Bilge piping for pump rooms and adjacent cofferdams on tank vessels...

46 CFR 32.52-5 - Bilge piping for pump rooms and adjacent cofferdams on tank vessels constructed or converted on...

Code of Federal Regulations, 2010 CFR

2010-10-01

... as complying with this provision, or alternatively, the pump controls shall be arranged so that they... 46 Shipping 1 2010-10-01 2010-10-01 false Bilge piping for pump rooms and adjacent cofferdams on... REQUIREMENTS Bilge Systems § 32.52-5 Bilge piping for pump rooms and adjacent cofferdams on tank vessels...

46 CFR 32.52-5 - Bilge piping for pump rooms and adjacent cofferdams on tank vessels constructed or converted on...

Code of Federal Regulations, 2012 CFR

2012-10-01

... as complying with this provision, or alternatively, the pump controls shall be arranged so that they... 46 Shipping 1 2012-10-01 2012-10-01 false Bilge piping for pump rooms and adjacent cofferdams on... REQUIREMENTS Bilge Systems § 32.52-5 Bilge piping for pump rooms and adjacent cofferdams on tank vessels...

Nutrient cycling Microbial Ecosystems: Assembly, Function and Targeted Design

DTIC Science & Technology

2017-05-05

different chemical transformations, converting potentially harmful chemicals via a series of intermediates, to harmless waste products. This shuttling of...Report: Nutrient-cycling Microbial Ecosystems: Assembly, Function and Targeted Design The views, opinions and/or findings contained in this report...are those of the author(s) and should not contrued as an official Department of the Army position, policy or decision, unless so designated by other

Buoyancy prime mover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Everett, T.D.

1982-12-14

A buoyancy prime mover that converts the potential energy of a gas buoyant within a liquid into rotating mechanical energy comprises a plurality of rigid or collapsible buckets joined by one or more chains with rotatable sprockets and shafts to form a continuous loop so that when the buoyant gas is trapped within the buckets, the buckets rise through the liquid and rotate the chain and sprockets to generate power.

Genomic analysis of diploid plants.

PubMed Central

Kimber, G; Yen, Y

1990-01-01

The numerical analysis of meiosis in the triploid hybrid between an induced autotetraploid and a related diploid provides the basis for investigations of the genomic relationships of diploid species based on chromosome pairing. It is also possible to make legitimate comparisons between different triploid hybrids of this type so that the genomic relationships can be converted into measures of phylogenetic distance for taxa where only diploids are known. PMID:11607075

Digital Biological Converter

DTIC Science & Technology

2013-06-28

of cuts that each fragment should be cut into so the fragments are no greater than a specific length threshold. Additionally, vector sequences and...restriction sites are attached to each fragment while ensuring the restriction sites are unique to each sequence. The vector sequences serve as hooks...for assembly into vector for cloning purposes, and also as primer binding domains for PCR ampl ification. The restriction sites are added to

40 CFR 86.007-17 - On-board Diagnostics for engines used in applications less than or equal to 14,000 pounds GVWR.

Code of Federal Regulations, 2010 CFR

2010-07-01

... catalytic converter. (ii) Diesel. Lack of cylinder combustion must be detected. (3) Exhaust gas sensors—(i... Model Year New Gasoline Fueled, Natural Gas-Fueled, Liquefied Petroleum Gas-Fueled and Methanol-Fueled...; calculated load; air flow rate from mass air flow sensor (if so equipped); fuel rate; and DPF delta pressure...

40 CFR 86.007-17 - On-board Diagnostics for engines used in applications less than or equal to 14,000 pounds GVWR.

Code of Federal Regulations, 2011 CFR

2011-07-01

... catalytic converter. (ii) Diesel. Lack of cylinder combustion must be detected. (3) Exhaust gas sensors—(i... Model Year New Gasoline Fueled, Natural Gas-Fueled, Liquefied Petroleum Gas-Fueled and Methanol-Fueled...; calculated load; air flow rate from mass air flow sensor (if so equipped); fuel rate; and DPF delta pressure...

Elaboration of tetra-orthogonally-substituted aromatic scaffolds towards novel EGFR-kinase inhibitors.

PubMed

Close, Adam J; Jones, Rhiannon N; Ocasio, Cory A; Kemmitt, Paul; Roe, S Mark; Spencer, John

2016-09-21

Nitration of three regioisomers of bromo-fluorobenzaldehyde proceeds regioselectively, notably with H2SO4/HNO3 at 0 °C. The thereby synthesized tetrasubstituted aromatics, endowed with orthogonal substituents, can be elaborated via Pd-catalysed coupling, reduction and reductive amination reactions. As a test-case, these compounds were converted into EGFR inhibitors related to Gefitinib, whose activity was rationalised by docking studies.

The importance of source configuration in quantifying footprints of regional atmospheric sulphur deposition.

PubMed

Vieno, M; Dore, A J; Bealey, W J; Stevenson, D S; Sutton, M A

2010-01-15

An atmospheric transport-chemistry model is applied to investigate the effects of source configuration in simulating regional sulphur deposition footprints from elevated point sources. Dry and wet depositions of sulphur are calculated for each of the 69 largest point sources in the UK. Deposition contributions for each point source are calculated for 2003, as well as for a 2010 emissions scenario. The 2010 emissions scenario has been chosen to simulate the Gothenburg protocol emission scenario. Point source location is found to be a major driver of the dry/wet deposition ratio for each deposition footprint, with increased precipitation scavenging of SO(x) in hill areas resulting in a larger fraction of the emitted sulphur being deposited within the UK for sources located near these areas. This reduces exported transboundary pollution, but, associated with the occurrence of sensitive soils in hill areas, increases the domestic threat of soil acidification. The simulation of plume rise using individual stack parameters for each point source demonstrates a high sensitivity of SO(2) surface concentration to effective source height. This emphasises the importance of using site-specific information for each major stack, which is rarely included in regional atmospheric pollution models, due to the difficulty in obtaining the required input data. The simulations quantify how the fraction of emitted SO(x) exported from the UK increases with source magnitude, effective source height and easterly location. The modelled reduction in SO(x) emissions, between 2003 and 2010 resulted in a smaller fraction being exported, with the result that the reductions in SO(x) deposition to the UK are less than proportionate to the emission reduction. This non-linearity is associated with a relatively larger fraction of the SO(2) being converted to sulphate aerosol for the 2010 scenario, in the presence of ammonia. The effect results in less-than-proportional UK benefits of reducing in SO(2) emissions, together with greater-than-proportional benefits in reducing export of UK SO(2) emissions. Copyright 2009 Elsevier B.V. All rights reserved.

Electoral surveys’ influence on the voting processes: a cellular automata model

NASA Astrophysics Data System (ADS)

Alves, S. G.; Oliveira Neto, N. M.; Martins, M. L.

2002-12-01

Nowadays, in societies threatened by atomization, selfishness, short-term thinking, and alienation from political life, there is a renewed debate about classical questions concerning the quality of democratic decision making. In this work a cellular automata model for the dynamics of free elections, based on the social impact theory is proposed. By using computer simulations, power-law distributions for the size of electoral clusters and decision time have been obtained. The major role of broadcasted electoral surveys in guiding opinion formation and stabilizing the “status quo” was demonstrated. Furthermore, it was shown that in societies where these surveys are manipulated within the universally accepted statistical error bars, even a majoritary opposition could be hindered from reaching power through the electoral path.

Ideological Consumerism in Colombian Elections, 2015: Links Between Political Ideology, Twitter Activity, and Electoral Results

PubMed Central

Camargo, Jorge E.

2017-01-01

Abstract Propagation of political ideologies in social networks has shown a substantial impact on voting behavior. Both the contents of the messages (the ideology) and the politicians' influence on their online audiences (their followers) have been associated with such an impact. In this study we evaluate which of these factors exerted a major role in deciding electoral results of the 2015 Colombian regional elections by evaluating the linguistic similarity of political ideologies and their influence on the Twitter sphere. The electoral results proved to be strongly associated with tweets and retweets and not with the linguistic content of their ideologies or politicians' followers in Twitter. Finally, suggestions for new ways to analyze electoral processes are discussed. PMID:28080152

Ideological Consumerism in Colombian Elections, 2015: Links Between Political Ideology, Twitter Activity, and Electoral Results.

PubMed

Correa, Juan C; Camargo, Jorge E

2017-01-01

Propagation of political ideologies in social networks has shown a substantial impact on voting behavior. Both the contents of the messages (the ideology) and the politicians' influence on their online audiences (their followers) have been associated with such an impact. In this study we evaluate which of these factors exerted a major role in deciding electoral results of the 2015 Colombian regional elections by evaluating the linguistic similarity of political ideologies and their influence on the Twitter sphere. The electoral results proved to be strongly associated with tweets and retweets and not with the linguistic content of their ideologies or politicians' followers in Twitter. Finally, suggestions for new ways to analyze electoral processes are discussed.

Input current shaped ac-to-dc converters

NASA Technical Reports Server (NTRS)

1985-01-01

Input current shaping techniques for ac-to-dc converters were investigated. Input frequencies much higher than normal, up to 20 kHz were emphasized. Several methods of shaping the input current waveform in ac-to-dc converters were reviewed. The simplest method is the LC filter following the rectifier. The next simplest method is the resistor emulation approach in which the inductor size is determined by the converter switching frequency and not by the line input frequency. Other methods require complicated switch drive algorithms to construct the input current waveshape. For a high-frequency line input, on the order of 20 kHz, the simple LC cannot be discarded so peremptorily, since the inductor size can be compared with that for the resistor emulation method. In fact, since a dc regulator will normally be required after the filter anyway, the total component count is almost the same as for the resistor emulation method, in which the filter is effectively incorporated into the regulator.

A waveguide frequency converter connecting rubidium-based quantum memories to the telecom C-band.

PubMed

Albrecht, Boris; Farrera, Pau; Fernandez-Gonzalvo, Xavier; Cristiani, Matteo; de Riedmatten, Hugues

2014-02-27

Coherently converting the frequency and temporal waveform of single and entangled photons will be crucial to interconnect the various elements of future quantum information networks. Of particular importance is the quantum frequency conversion of photons emitted by material systems able to store quantum information, so-called quantum memories. There have been significant efforts to implement quantum frequency conversion using nonlinear crystals, with non-classical light from broadband photon-pair sources and solid-state emitters. However, solid state quantum frequency conversion has not yet been achieved with long-lived optical quantum memories. Here we demonstrate an ultra-low-noise solid state photonic quantum interface suitable for connecting quantum memories based on atomic ensembles to the telecommunication fibre network. The interface is based on an integrated-waveguide nonlinear device. We convert heralded single photons at 780 nm from a rubidium-based quantum memory to the telecommunication wavelength of 1,552 nm, showing significant non-classical correlations between the converted photon and the heralding signal.

Gender quotas for women in national politics: A comparative analysis across development thresholds.

PubMed

Rosen, Jennifer

2017-08-01

Women's share of global lower or single house parliamentary seats has increased by over 70% over the course of the 21st century. Yet these increases have not been uniform across countries. Rather countries with low levels of socioeconomic development have outpaced developed democracies in terms of the gains made in the formal political representation of women. One reasonable explanation for this trend is the adoption in many poorer countries of national gender quota legislation, that is, affirmative action laws intended to compensate for sex discrimination in the electoral process. Yet, cross-national analyses examining quotas as an explanatory factor typically use a simple binary (yes/no) variable that either conflates the diverse intra-quota variations into a single variable or includes only one part of the many quota variations. By contrast, using an originally compiled dataset that includes 167 countries from 1992 to 2012, this paper employs measures of gender quota legislation that capture the complexity and considerable diversity of existing quota legislation. These measures allow us to identify the specific factors that have helped so many less developed countries rise to the top of international rankings in recent years. The findings indicate that the effect of each type of gender quota, as well as other explanatory variables, do not operate in the same way across all countries. Specifically, voluntary political party quotas are substantially more effective in developed countries, while reserved seat quotas are only significant in least developed countries. Electoral candidate quotas, on the other hand, can be significant across all countries, however only have a positive effect when they are accompanied by placement mandates that ensure women are placed in winnable positions, sanctions for non-compliance that are significant enough to force adherence, and a minimum mandated threshold of at least 30%. Copyright © 2017 Elsevier Inc. All rights reserved.

Clustering of cycloidal wave energy converters

DOEpatents

Siegel, Stefan G.

2016-03-29

A wave energy conversion system uses a pair of wave energy converters (WECs) on respective active mountings on a floating platform, so that the separation of the WECs from each other or from a central WEC can be actively adjusted according to the wavelength of incident waves. The adjustable separation facilitates operation of the system to cancel reactive forces, which may be generated during wave energy conversion. Modules on which such pairs of WECs are mounted can be assembled with one or more central WECs to form large clusters in which reactive forces and torques can be made to cancel. WECs of different sizes can be employed to facilitate cancelation of reactive forces and torques.

A new electronic scanner of pressure designed for installation in wind-tunnel models

NASA Technical Reports Server (NTRS)

Coe, C. T.; Parra, G. T.; Kauffman, R. C.

1981-01-01

A new electronic scanner of pressure (ESOP) has been developed by NASA Ames Research Center for installation in wind-tunnel models. An ESOP system includes up to 20 pressure modules, each with 48 pressure transducers, an A/D converter, a microprocessor, a data controller, a monitor unit, and a heater controller. The system is sized so that the pressure modules and A/D converter module can be installed within an average-size model tested in the Ames Aerodynamics Division wind tunnels. This paper describes the ESOP system, emphasizing the main element of the system - the pressure module. The measured performance of the overall system is also presented.

The development of health law as a way to change traditional attitudes in national legal systems. The influence of international human rights law: what is left for the national legislator?

PubMed

Birmontiene, Toma

2010-03-01

The development of health law as a sovereign subject of law could be seen as a correlative result of the development of international human rights law. From the perspectives of human rights law, health law gives us a unique possibility to change the traditional point of reference - from the regulation of medical procedures, to the protection of human rights as the main objective of law. At the end of the twentieth and the beginning of this century, human rights law and the most influential international instrument--the European Convention on Human Rights (and the jurisprudence of the ECHR) has influenced health care so much that it has became difficult to draw a line between these subjects. Health law sometimes directly influences and even aspires to change the content of Convention rights that are considered to be traditional. However, certain problems of law linked to health law are decided without influencing the essence of rights protected by the Convention, but just by construing the particularities of application of a certain right. In some cases by further developing the requirements of protection of individual rights that are also regulated by the health law, the ECHR even "codifies" some fields of health law (e.g., the rights of persons with mental disorders). The recognition of worthiness and diversity of human rights and the development of their content raise new objectives for national legislators when they regulate the national legal system. Here the national legislator is often put into a quandary whether to implement the standards of human rights that are recognized by the international community, or to refuse to do so, taking account of the interests of a certain group of the electorate.

USSR Report, International Affairs, The Working Class and the Contemporary World, Number 6, November-December 1985

DTIC Science & Technology

1986-07-14

called people’s parties which lose the specifics of their make-up as the ruling parties become the government party. The electorate of the "traditional...an electoral choice, which presupposed above all evaluation of the personal qualities of one political leader or another. An objective need arose...that Suarez proved to be legitimated in mass consciousness as the almost "natural" head of the new course, even before an electoral mandate was given

Linear induction accelerator

DOEpatents

Buttram, M.T.; Ginn, J.W.

1988-06-21

A linear induction accelerator includes a plurality of adder cavities arranged in a series and provided in a structure which is evacuated so that a vacuum inductance is provided between each adder cavity and the structure. An energy storage system for the adder cavities includes a pulsed current source and a respective plurality of bipolar converting networks connected thereto. The bipolar high-voltage, high-repetition-rate square pulse train sets and resets the cavities. 4 figs.

Angiotensin-(1-7)-Induced Plasticity Changes in the Lateral Amygdala Are Mediated by COX-2 and NO

ERIC Educational Resources Information Center

Albrecht, Doris

2007-01-01

It is known from studies outside the brain that upon binding to its receptor, angiotensin-(1-7) elicits the release of prostanoids and nitric oxide (NO). Cyclooxygenase (COX) is a key enzyme that converts arachidonic acid to prostaglandins. Since there are no data available so far on the role of COX-2 in the amygdala, in a first step we…

Air Force Command and Control: The Path Ahead. Volume 1: Summary

DTIC Science & Technology

2000-12-01

benefits of an integrated approach to implementation. The organization, management, and process are not in place to carry out the evolution in...critical support for successful EAF operations. 9 Air Force Space Operations Center (AFSPACE) AOC. The 14th Air Force AFSPACE AOC is an in- place ...right times and places , so that they can pass consistent data that convert to shared understanding, ultimately producing cooperative decision making

Improved gaseous leak detector

DOEpatents

Juravic, F.E. Jr.

1983-10-06

In a short path length mass-spectrometer type of helium leak detector wherein the helium trace gas is ionized, accelerated and deflected onto a particle counter, an arrangement is provided for converting the detector to neon leak detection. The magnetic field of the deflection system is lowered so as to bring the nonlinear fringe area of the magnetic field across the ion path, thereby increasing the amount of deflection of the heavier neon ions.

Gaseous leak detector

DOEpatents

Juravic, Jr., Frank E.

1988-01-01

In a short path length mass-spectrometer type of helium leak detector wherein the helium trace gas is ionized, accelerated and deflected onto a particle counter, an arrangement is provided for converting the detector to neon leak detection. The magnetic field of the deflection system is lowered so as to bring the non linear fringe area of the magnetic field across the ion path, thereby increasing the amount of deflection of the heavier neon ions.

Prototype Combined Heater/Thermoelectric Power Generator for Remote Applications

NASA Astrophysics Data System (ADS)

Champier, D.; Favarel, C.; Bédécarrats, J. P.; Kousksou, T.; Rozis, J. F.

2013-07-01

This study presents a prototype thermoelectric generator (TEG) developed for remote applications in villages that are not connected to the electrical power grid. For ecological and economic reasons, there is growing interest in harvesting waste heat from biomass stoves to produce some electricity. Because regular maintenance is not required, TEGs are an attractive choice for small-scale power generation in inaccessible areas. The prototype developed in our laboratory is especially designed to be implemented in stoves that are also used for domestic hot water heating. The aim of this system is to provide a few watts to householders, so they have the ability to charge cellular phones and radios, and to get some light at night. A complete prototype TEG using commercial (bismuth telluride) thermoelectric modules has been built, including system integration with an electric DC/DC converter. The DC/DC converter has a maximum power point tracker (MPPT) driven by an MC9SO8 microcontroller, which optimizes the electrical energy stored in a valve-regulated lead-acid battery. Physical models were used to study the behavior of the thermoelectric system and to optimize the performance of the MPPT. Experiments using a hot gas generator to simulate the exhaust of the combustion chamber of a stove are used to evaluate the system. Additionally, potential uses of such generators are presented.

[Putting decriminalization of abortion to a refendum].

PubMed

1997-09-01

Surveys conducted in Mexico by GIRE in 1992, 1994, and 1995 reveal that over 80% of the national population believes only a woman or a woman and her partner should make abortion decisions. Neither the government, the Church, nor physicians should intervene. Public opinion and the documented social and public health consequences of illegal abortion demonstrate the obsolescence of laws penalizing abortion. Mexico does not have a direct means of converting the opinions of the population into votes and laws. In place of referendums, committees of specialists have been convened; they are limited in number and ability to represent diverse groups, and oriented above all to the losses and gains of political and parliamentary disputes. The electoral reform of 1995-96 was a good example of the question under debate getting lost in partisan maneuvering. The Federal District and four states have initiated development of the referendum process, but the procedures have been too cumbersome and the results disappointing. In the current day, opinions are often formed not by following a rational process, but by bombardment with advertising appealing to irrational emotions. The democratic effects of referendum should be furthered by guaranteeing fair and exhaustive exposure of all points of view before the vote is held. GIRE recommends that a referendum on decriminalization of abortion should be preceded by a period of at least two years for public debate and reflection, and that the Federal Electoral Institute should organize the debate and the referendum.

Carboxylate platform: the MixAlco process part 1: comparison of three biomass conversion platforms.

PubMed

Holtzapple, Mark T; Granda, Cesar B

2009-05-01

To convert biomass to liquid fuels, three platforms are compared: thermochemical, sugar, and carboxylate. To create a common basis, each platform is fed "ideal biomass," which contains polysaccharides (68.3%) and lignin (31.7%). This ratio is typical of hardwood biomass and was selected so that when gasified and converted to hydrogen, the lignin has sufficient energy to produce ethanol from the carboxylic acids produced by the carboxylate platform. Using balanced chemical reactions, the theoretical yield and energy efficiency were determined for each platform. For all platforms, the ethanol yield can be increased by 71% to 107% by supplying external hydrogen produced from other sources (e.g., solar, wind, nuclear, fossil fuels). The alcohols can be converted to alkanes with a modest loss of energy efficiency (3 to 5 percentage points). Of the three platforms considered, the carboxylate platform has demonstrated the highest product yields.

Experimental and theoretical investigation for the suppression of the plasma arc drop in the thermionic converter

NASA Technical Reports Server (NTRS)

Shaw, D. T.; Manikopoulos, C. N.; Chang, T.; Lee, C. H.; Chiu, N.

1977-01-01

Ion generation and recombination mechanisms in the cesium plasma as they pertain to the advanced mode thermionic energy converter were studied. The decay of highly ionized cesium plasma was studied in the near afterglow to examine the recombination processes. Very low recombination in such a plasma may prove to be of considerable importance in practical converters. The approaches of external cesium generation were vibrationally excited nitrogen as an energy source of ionization of cesium ion, and microwave power as a means of resonant sustenance of the cesium plasma. Experimental data obtained so far show that all three techniques - i.e., the non-LTE high-voltage pulsing, the energy transfer from vibrationally excited diatomic gases, and the external pumping with a microwave resonant cavity - can produce plasmas with their densities significantly higher than the Richardson density. The implication of these findings as related to Lam's theory is discussed.

Development of monitoring and control system for a mine main fan based on frequency converter

NASA Astrophysics Data System (ADS)

Zhang, Y. C.; Zhang, R. W.; Kong, X. Z.; Y Gong, J.; Chen, Q. G.

2013-12-01

In the process of mine exploitation, the requirement of air flow rate often changes. The procedure of traditional control mode of the fan is complex and it is hard to meet the worksite requirement for air. This system is based on Principal Computer (PC) monitoring system and high performance PLC control system. In this system, the frequency converter is adapted to adjust the fan speed and the air of worksite can be regulated steplessly. The function of the monitoring and control system contains on-line monitoring and centralized control. The system can monitor the parameters of fan in real-time, control the operation of frequency converter, as well as, control the fan and its accessory equipments. At the same time, the automation level of the system is highly, the field equipments can be monitored and controlled automatically. So, the system is an important safeguard for mine production.

[Research progress of mechanism and prevention of peritendinous adhesions].

PubMed

Jiang, Shichao; Liu, Shen; Fan, Cunyi

2013-05-01

To review the research progress of mechanism and prevention of peritendinous adhesions. Methods Recent literature about peritendinous adhesions was reviewed, and the results from experiments about the mechanism and prevention of peritendinous adhesions were analyzed. The molecular mechanism of peritendinous adhesions is related to overexpressions of transforming growth factor beta 1, early growth response protein 1, matrix metallopeptidase 9, and so on. The present methods of prevention of peritendinous adhesions include drugs, barrier, optimizing rehabilitation, gene therapy, and so on. These methods have achieved good results in experiments, but the clinical applications have not been confirmed yet. It is necessary to pay more attention to the research of mechanism of peritendinous adhesions and methods of its prevention and subsequently to convert them into clinical applications, which is significant to the prevention of peritendinous adhesions in the future.

Hydrothermal synthesis of ultralong and single-crystalline Cd(OH)2 nanowires using alkali salts as mineralizers.

PubMed

Tang, Bo; Zhuo, Linhai; Ge, Jiechao; Niu, Jinye; Shi, Zhiqiang

2005-04-18

Ultralong and single-crystalline Cd(OH)(2) nanowires were fabricated by a hydrothermal method using alkali salts as mineralizers. The morphology and size of the final products strongly depend on the effects of the alkali salts (e.g., KCl, KNO(3), and K(2)SO(4) or NaCl, NaNO(3), and Na(2)SO(4)). When the salt is absent, only nanoparticles are observed in TEM images of the products. The 1D nanostructure growth method presented herein offers an excellent tool for the design of other advanced materials with anisotropic properties. In addition, the Cd(OH)(2) nanowires might act as a template or precursor that is potentially converted into 1D cadmium oxide through dehydration or into 1D nanostructures of other functional materials (e.g., CdS, CdSe).

Elucidation of conditions allowing conversion of penicillin G and other penicillins to deacetoxycephalosporins by resting cells and extracts of Streptomyces clavuligerus NP1

PubMed Central

Cho, Hiroshi; Adrio, José L.; Luengo, José M.; Wolfe, Saul; Ocran, Simeon; Hintermann, Gilberto; Piret, Jacqueline M.; Demain, Arnold L.

1998-01-01

Using resting cells and extracts of Streptomyces clavuligerus NP1, we have been able to convert penicillin G (benzylpenicillin) to deacetoxycephalosporin G. Conversion was achieved by increasing by 45× the concentration of FeSO4 (1.8 mM) and doubling the concentration of α-ketoglutarate (1.28 mM) as compared with standard conditions used for the normal cell-free conversion of penicillin N to deacetoxycephalosporin C. ATP, MgSO4, KCl, and DTT, important in cell-free expansion of penicillin N, did not play a significant role in the ring expansion of penicillin G by resting cells or cell-free extracts. When these conditions were used with 14 other penicillins, ring expansion was achieved in all cases. PMID:9751702

Direct Production of Furfural in One-pot Fashion from Raw Biomass Using Brønsted Acidic Ionic Liquids.

PubMed

Matsagar, Babasaheb M; Hossain, Shahriar A; Islam, Tofazzal; Alamri, Hatem R; Alothman, Zeid A; Yamauchi, Yusuke; Dhepe, Paresh L; Wu, Kevin C-W

2017-10-18

The conversion of raw biomass into C5-sugars and furfural was demonstrated with the one-pot method using Brønsted acidic ionic liquids (BAILs) without any mineral acids or metal halides. Various BAILs were synthesized and characterized using NMR, FT-IR, TGA, and CHNS microanalysis and were used as the catalyst for raw biomass conversion. The remarkably high yield (i.e. 88%) of C5 sugars from bagasse can be obtained using 1-methyl-3(3-sulfopropyl)-imidazolium hydrogen sulfate ([C 3 SO 3 HMIM][HSO 4 ]) BAIL catalyst in a water medium. Similarly, the [C 3 SO 3 HMIM][HSO 4 ] BAIL also converts the bagasse into furfural with very high yield (73%) in one-pot method using a water/toluene biphasic solvent system.

Statistical analysis of Brazilian electoral campaigns via Benford's law

NASA Astrophysics Data System (ADS)

Gamermann, Daniel; Antunes, Felipe Leite

2018-04-01

The principle of democracy is that the people govern through elected representatives. Therefore, a democracy is healthy as long as the elected politicians do represent the people. We have analyzed data from the Brazilian electoral court (Tribunal Superior Eleitoral, TSE) concerning money donations for the electoral campaigns and the election results. Our work points to two conclusions that combined may be in conflict with the democratic principle: money is the determining factor on whether a candidate is elected or not (opposed to representativeness); secondly, the use of Benford's Law to analyze the declared donations received by the parties and electoral campaigns shows either possible manipulations in the declarations or a significant number of donations that might not have been spontaneous from the donors. The better term that describes Brazil's government system is plutocracy (govern by the wealthy).

In vitro replication and thermodynamic studies of methylation and oxidation modifications of 6-thioguanine.

PubMed

Gu, Chunang; Wang, Yinsheng

2007-01-01

The cytotoxic effects of thiopurine drugs are mostly exerted through the formation of thioguanine nucleotide and its subsequent incorporation into DNA. The 6-thioguanine (6-TG) in DNA can be converted to S6-methylthio-2-aminopurine (2-AP-6-SCH3) and 2-aminopurine-6-sulfonic acid (2-AP-6-SO3H) upon reaction with S-adenosyl-L-methionine and irradiation with UVA light, respectively. Here we prepared oligodeoxynucleotides (ODNs) harboring a 6-TG, 2-AP-6-SCH3 or 2-AP-6-SO3H at a defined site and examined, by using LC-MS/MS, the in vitro replication of these substrates with yeast polymerase eta and Klenow fragment (KF-). Our results revealed that 2-AP-6-SCH3 could be bypassed by KF-, with significant misincorporation of thymine opposite the lesion. The 2-AP-6-SO3H, however, blocked markedly the nucleotide insertion by KF-. Yeast pol eta could bypass all three modified nucleosides; although dCMP was inserted preferentially, we found substantial misincorporation of dTMP and dAMP opposite 2-AP-6-SCH3 and 2-AP-6-SO3H, respectively. Moreover, both KF- and yeast pol eta induced a considerable amount of -2 frameshift products from the replication of 2-AP-6-SCH3- and 2-AP-6-SO3H-bearing substrates. Our results also underscored the importance of measuring the relative ionization efficiencies of replication products in the accurate quantification of these products by LC-MS/MS. Moreover, thermodynamic studies revealed that 2-AP-6-SCH3 and 2-AP-6-SO3H could cause more destabilization to duplex DNA than 6-TG. Taken together, the results from this study shed important new light on the biological implications of the two metabolites of 6-TG.

In vitro replication and thermodynamic studies of methylation and oxidation modifications of 6-thioguanine

PubMed Central

Wang, Yinsheng

2007-01-01

The cytotoxic effects of thiopurine drugs are mostly exerted through the formation of thioguanine nucleotide and its subsequent incorporation into DNA. The 6-thioguanine (6-TG) in DNA can be converted to S6-methylthio-2-aminopurine (2-AP-6-SCH3) and 2-aminopurine-6-sulfonic acid (2-AP-6-SO3H) upon reaction with S-adenosyl-L-methionine and irradiation with UVA light, respectively. Here we prepared oligodeoxynucleotides (ODNs) harboring a 6-TG, 2-AP-6-SCH3 or 2-AP-6-SO3H at a defined site and examined, by using LC-MS/MS, the in vitro replication of these substrates with yeast polymerase η and Klenow fragment (KF−). Our results revealed that 2-AP-6-SCH3 could be bypassed by KF−, with significant misincorporation of thymine opposite the lesion. The 2-AP-6-SO3H, however, blocked markedly the nucleotide insertion by KF−. Yeast pol η could bypass all three modified nucleosides; although dCMP was inserted preferentially, we found substantial misincorporation of dTMP and dAMP opposite 2-AP-6-SCH3 and 2-AP-6-SO3H, respectively. Moreover, both KF− and yeast pol η induced a considerable amount of -2 frameshift products from the replication of 2-AP-6-SCH3- and 2-AP-6-SO3H-bearing substrates. Our results also underscored the importance of measuring the relative ionization efficiencies of replication products in the accurate quantification of these products by LC-MS/MS. Moreover, thermodynamic studies revealed that 2-AP-6-SCH3 and 2-AP-6-SO3H could cause more destabilization to duplex DNA than 6-TG. Taken together, the results from this study shed important new light on the biological implications of the two metabolites of 6-TG. PMID:17517786

Radiation tolerant power converter controls

NASA Astrophysics Data System (ADS)

Todd, B.; Dinius, A.; King, Q.; Uznanski, S.

2012-11-01

The Large Hadron Collider (LHC) at the European Organisation for Nuclear Research (CERN) is the world's most powerful particle collider. The LHC has several thousand magnets, both warm and super-conducting, which are supplied with current by power converters. Each converter is controlled by a purpose-built electronic module called a Function Generator Controller (FGC). The FGC allows remote control of the power converter and forms the central part of a closed-loop control system where the power converter voltage is set, based on the converter output current and magnet-circuit characteristics. Some power converters and FGCs are located in areas which are exposed to beam-induced radiation. There are numerous radiation induced effects, some of which lead to a loss of control of the power converter, having a direct impact upon the accelerator's availability. Following the first long shut down (LS1), the LHC will be able to run with higher intensity beams and higher beam energy. This is expected to lead to significantly increased radiation induced effects in materials close to the accelerator, including the FGC. Recent radiation tests indicate that the current FGC would not be sufficiently reliable. A so-called FGClite is being designed to work reliably in the radiation environment in the post-LS1 era. This paper outlines the concepts of power converter controls for machines such as the LHC, introduces the risks related to radiation and a radiation tolerant project flow. The FGClite is then described, with its key concepts and challenges: aiming for high reliability in a radiation field.

Chappy Oblique

NASA Image and Video Library

2016-03-30

Looking east to west across the rim and down into Chaplygin crater reveals this beautiful example of a fresh young crater and its perfectly preserved ejecta blanket. The delicate patterns of flow across, over, and down local topography clearly show that ejecta traveled as a ground hugging flow for great distances, rather than simply being tossed out on a ballistic trajectory. Very near the rim lies a dark, lacy, discontinuous crust of now frozen impact melt. Clearly this dark material is on top of the bright material so it was the very last material ejected from the crater. The melt was formed as the tremendous energy of impact was converted to heat and the lunar crust was melted at the impact point. As the crater rebounded and material sloughed down the walls of the deforming crater the melt was splashed out over the rim and froze. Its low reflectance is mostly due to a high percentage of glass because the melt cooled so quickly that minerals did not have time to crystallize. The fact that the delicate splash patterns are so well preserved testifies to the very young age of this crater. But how young? For comparison "Chappy" (informal name) is 200 m larger than Meteor crater (1200 m diameter) in Arizona, which is about 50,000 years old. Craters of this size form every 100,000 years or so on the Moon and the Earth. Since there are very few superposed craters on Chappy, and its ejecta is so perfectly preserved it may be much younger than Meteor crater. However, we can't know the true true absolute age of "Chappy" until we can obtain a sample of its impact melt for radiometric age dating. Credit: NASA/Goddard/Arizona State University/LRO/LROC

Chappy Oblique

NASA Image and Video Library

2017-12-08

Looking east to west across the rim and down into Chaplygin crater reveals this beautiful example of a fresh young crater and its perfectly preserved ejecta blanket. The delicate patterns of flow across, over, and down local topography clearly show that ejecta traveled as a ground hugging flow for great distances, rather than simply being tossed out on a ballistic trajectory. Very near the rim lies a dark, lacy, discontinuous crust of now frozen impact melt. Clearly this dark material is on top of the bright material so it was the very last material ejected from the crater. The melt was formed as the tremendous energy of impact was converted to heat and the lunar crust was melted at the impact point. As the crater rebounded and material sloughed down the walls of the deforming crater the melt was splashed out over the rim and froze. Its low reflectance is mostly due to a high percentage of glass because the melt cooled so quickly that minerals did not have time to crystallize. The fact that the delicate splash patterns are so well preserved testifies to the very young age of this crater. But how young? For comparison "Chappy" (informal name) is 200 m larger than Meteor crater (1200 m diameter) in Arizona, which is about 50,000 years old. Craters of this size form every 100,000 years or so on the Moon and the Earth. Since there are very few superposed craters on Chappy, and its ejecta is so perfectly preserved it may be much younger than Meteor crater. However, we can't know the true true absolute age of "Chappy" until we can obtain a sample of its impact melt for radiometric age dating. Investigate all of Chappy's ejecta, at full resolution: lroc.sese.asu.edu/posts/901 Credit: NASA/Goddard/Arizona State University/LRO/LROC

Physicochemical effects on sulfite transformation in a lipid-rich Chlorella sp. strain

NASA Astrophysics Data System (ADS)

Liang, Fang; Wen, Xiaobin; Luo, Liming; Geng, Yahong; Li, Yeguang

2014-11-01

SO2 is very rapidly hydrated to sulfurous acid in water solution at pH value above 6.0, whereby sulfite is yielded from the disassociation of protons. We aimed to improve the sulfite transformation efficiency and provide a basis for the direct utilization of SO2 from flue gas by a microalgal suspension. Chlorella sp. XQ-20044 was cultured in a medium with 20 mmol/L sodium sulfite under different physicochemical conditions. Under light conditions, sulfite concentration in the algal suspension reduced linearly over time, and was completely converted into sulfate within 8 h. The highest sulfite transformation rate (3.25 mmol/(L·h)) was obtained under the following conditions: 35°C, light intensity of 300 μmol/(m2·s), NaHCO3 concentration of 6 g/L, initial cell density (OD540) of 0.8 and pH of 9-10. There was a positive correlation between sulfite transformation rate and the growth of Chlorella, with the conditions favorable to algal growth giving better sulfite transformation. Although oxygen in the air plays a role in the transformation of SO2- 3 to SO2- 4, the transformation is mainly dependent on the metabolic activity of algal cells. Chlorella sp. XQ-20044 is capable of tolerating high sulfite concentration, and can utilize sulfite as the sole sulfur source for maintaining healthy growth. We found that sulfite ≤20 mmol/L had no obvious effect on the total lipid content and fatty acid profiles of the algae. Thus, the results suggest it is feasible to use flue gas for the mass production of feedstock for biodiesel using Chlorella sp. XQ-20044, without preliminary removal of SO2, assuming there is adequate control of the pH.

Overcoming difficulties with caviar formation, desanding of converter I, Leuna, 1941

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1941-01-01

The life of a coal stall was in most cases limited by the grinding action of the solid components of the coal. The so-called caviar produced the greatest amount of difficulties. Its elimination was accomplished by the removal of the coarsest particle from the first converter, the converter 1 desanding. Before desanding was introduced, perforated thermocouple-protecting tubes and catalyst tubes almost ground through were found in almost every dismantling of the stalls. Small-scale and large-scale solutions to this problem were discussed. A sketch of desanding in converter I was given. Another sketch showed the pipe line of the HOLD frommore » the converter to the pressure relief. A screen analysis of the converter I desanding and of the normal HOLD were made to determine the proportion of coarse and fine sludge. Curve A and curve B given on two graphs showed the percent distribution and the actual amount involved. Sheet 1 gave diagrams of the residue and damage by wear in converters 1 and 2 of stall 8. Sheet 4 showed a diagram of converter 1 with an inclined plane for desanding and sheet 8 gave the desanding results from a test on converter 1. The final conclusion drawn was that desanding of converter 1 completely eliminated the formation and settling of caviar in the coal stall converters. The desanding process was one in which about 10% of the sludge in the first converter was periodically withdrawn from the bottom of converter, often to be sent on to be combined with hot oil letdown for further processing. The desanding residue could be readily carbonized because the proportion of asphalt to solids was very good. 8 diagrams« less

Particle/Continuum Hybrid Simulation in a Parallel Computing Environment

NASA Technical Reports Server (NTRS)

Baganoff, Donald

1996-01-01

The objective of this study was to modify an existing parallel particle code based on the direct simulation Monte Carlo (DSMC) method to include a Navier-Stokes (NS) calculation so that a hybrid solution could be developed. In carrying out this work, it was determined that the following five issues had to be addressed before extensive program development of a three dimensional capability was pursued: (1) find a set of one-sided kinetic fluxes that are fully compatible with the DSMC method, (2) develop a finite volume scheme to make use of these one-sided kinetic fluxes, (3) make use of the one-sided kinetic fluxes together with DSMC type boundary conditions at a material surface so that velocity slip and temperature slip arise naturally for near-continuum conditions, (4) find a suitable sampling scheme so that the values of the one-sided fluxes predicted by the NS solution at an interface between the two domains can be converted into the correct distribution of particles to be introduced into the DSMC domain, (5) carry out a suitable number of tests to confirm that the developed concepts are valid, individually and in concert for a hybrid scheme.

Physical and chemical pretreatment of lignocellulosics in pineapple (Ananus comosus) peels dried for investment

NASA Astrophysics Data System (ADS)

Sukkaew, Adulsman; Boonsong, Panthip; Thongpradistha, Sriubol; Intan, Maimoon

2017-08-01

Pineapple (Ananus comosus) Peels, once known as waste from agricultural, can be a problem when we eliminate in agriculture and industry. The current technology can help preliminarily to solve this problem. The sustainable solution to this problem is lignocellulosics pretreatments for converted saccharide as a carbon source for ethanol production. The objective of this study is the investigation of pineapple peels pretreatment to produce fermentable sugar by drying and digesting 5% sulfuric acid (H2SO4). And study of cost economic passed selection for investment. The result found that the best investment of drying was 100 °C at 11 hours for the sulphuric acid which could be easily crushed into a fine powder. Moreover, digestion of pineapple peels gave the best total sugar 252.2 g/l by 5% H2SO4 incubated for 60 minutes at room temperature. The pineapple peels were digested by 5%H2SO4 concentration by incubating for 60 minutes at room temperature, finding to be the best condition and the lowest investment. Finally, the optimisation of investment and management for lignocellulosic pretreatment will improve efficiency of strategy for economic and energy development.

Modeling and analysis of fractional order DC-DC converter.

PubMed

Radwan, Ahmed G; Emira, Ahmed A; AbdelAty, Amr M; Azar, Ahmad Taher

2017-07-11

Due to the non-idealities of commercial inductors, the demand for a better model that accurately describe their dynamic response is elevated. So, the fractional order models of Buck, Boost and Buck-Boost DC-DC converters are presented in this paper. The detailed analysis is made for the two most common modes of converter operation: Continuous Conduction Mode (CCM) and Discontinuous Conduction Mode (DCM). Closed form time domain expressions are derived for inductor currents, voltage gain, average current, conduction time and power efficiency where the effect of the fractional order inductor is found to be strongly present. For example, the peak inductor current at steady state increases with decreasing the inductor order. Advanced Design Systems (ADS) circuit simulations are used to verify the derived formulas, where the fractional order inductor is simulated using Valsa Constant Phase Element (CPE) approximation and Generalized Impedance Converter (GIC). Different simulation results are introduced with good matching to the theoretical formulas for the three DC-DC converter topologies under different fractional orders. A comprehensive comparison with the recently published literature is presented to show the advantages and disadvantages of each approach. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Monolithic quasi-sliding-mode controller for SIDO buck converter with a self-adaptive free-wheeling current level

NASA Astrophysics Data System (ADS)

Xiaobo, Wu; Qing, Liu; Menglian, Zhao; Mingyang, Chen

2013-01-01

An analog implementation of a novel fixed-frequency quasi-sliding-mode controller for single-inductor dual-output (SIDO) buck converter in pseudo-continuous conduction mode (PCCM) with a self-adaptive freewheeling current level (SFCL) is presented. Both small and large signal variations around the operation point are considered to achieve better transient response so as to reduce the cross-regulation of this SIDO buck converter. Moreover, an internal integral loop is added to suppress the steady-state regulation error introduced by conventional PWM-based sliding mode controllers. Instead of keeping it as a constant value, the free-wheeling current level varies according to the load condition to maintain high power efficiency and less cross-regulation at the same time. To verify the feasibility of the proposed controller, an SIDO buck converter with two regulated output voltages, 1.8 V and 3.3 V, is designed and fabricated in HEJIAN 0.35 μm CMOS process. Simulation and experiment results show that the transient time of this SIDO buck converter drops to 10 μs while the cross-regulation is reduced to 0.057 mV/mA, when its first load changes from 50 to 100 mA.

JPRS Report, East Europe.

DTIC Science & Technology

1992-11-20

Convention [DELO 6 Nov] 33 Transportation Agreement Talks Held With EC [DELO 2 Nov] 33 Government, Unions Sign Collective Contract [DELO 30 Oct] 34...the standpoint of current payments. Although it is possible that the forint’s de facto convertibility has expanded in a relative sense, it does not...They intend to continue this restriction for a while—and appropriately so, in my view. On the other hand, the forint’s de facto external

Navy Shipboard Lasers for Surface, Air, and Missile Defense: Background and Issues for Congress

DTIC Science & Technology

2013-06-27

include silicon carbide ( SiC )- based transistors, transformers and power converters. “ SiC is important because it improves power quality and reduces size...existing shipboard gun systems. An airborne mirror , perhaps mounted on an aerostat,11 could bounce light from a shipboard laser, so as to permit non-line...super conducting RF electron beam injectors, advanced high power cathode technologies, high power compact amplifiers, and advanced mirrors

Josephson A/D Converter Development.

DTIC Science & Technology

1981-10-01

by Zappe and A Landman [20]. They conclude that the simple model of the Josephson effect is applicable up to frequencies at least as high (a) as 300...GHz. B. Time-Domain Experiments 4ooF so The early high - frequency experiments with Josephson devices I .O suggested their use as very fast logic switches...exactly as for the phenomenological model . The tunneling pacitive current paths dominate the circuit at high frequencies . current is the sum of two

Mexico’s National Security Challenges and the Military Endeavor

DTIC Science & Technology

2013-03-01

liberalizing the economy) and on global economic integration. 11 So for a long time, political and economic considerations were the main priorities of...Constitucion Politica de los Estados Unidos Mexicanos, art 89 fracc. X Camara de Diputados del H. Congreso de la Union (Mexico: D.F. Gobierno de la...Convert Action Quarterly, No. 59 (Winter 1996-1997): 43. 8 Contitucion Politica de los Estados Unidos Mexicanos, art. 89 fracc. VI, 86. 9 Hernandez

Linear induction accelerator and pulse forming networks therefor

DOEpatents

Buttram, Malcolm T.; Ginn, Jerry W.

1989-01-01

A linear induction accelerator includes a plurality of adder cavities arranged in a series and provided in a structure which is evacuated so that a vacuum inductance is provided between each adder cavity and the structure. An energy storage system for the adder cavities includes a pulsed current source and a respective plurality of bipolar converting networks connected thereto. The bipolar high-voltage, high-repetition-rate square pulse train sets and resets the cavities.

Novel bidirectional DC-DC converters based on the three-state switching cell

NASA Astrophysics Data System (ADS)

da Silva Júnior, José Carlos; Robles Balestero, Juan Paulo; Lessa Tofoli, Fernando

2016-05-01

It is well known that there is an increasing demand for bidirectional DC-DC converters for applications that range from renewable energy sources to electric vehicles. Within this context, this work proposes novel DC-DC converter topologies that use the three-state switching cell (3SSC), whose well-known advantages over conventional existing structures are ability to operate at high current levels, while current sharing is maintained by a high frequency transformer; reduction of cost and dimensions of magnetics; improved distribution of losses, with consequent increase of global efficiency and reduction of cost associated to the need of semiconductors with lower current ratings. Three distinct topologies can be derived from the 3SSC: one DC-DC converter with reversible current characteristic able to operate in the first and second quadrants; one DC-DC converter with reversible voltage characteristic able to operate in the first and third quadrants and one DC-DC converter with reversible current and voltage characteristics able to operate in four quadrants. Only the topology with bidirectional current characteristic is analysed in detail in terms of the operating stages in both nonoverlapping and overlapping modes, while the design procedure of the power stage elements is obtained. In order to validate the theoretical assumptions, an experimental prototype is also implemented, so that relevant issues can be properly discussed.

Field experiment estimate of electoral fraud in Russian parliamentary elections

PubMed Central

Enikolopov, Ruben; Korovkin, Vasily; Petrova, Maria; Sonin, Konstantin; Zakharov, Alexei

2013-01-01

Electoral fraud is a widespread phenomenon, especially outside the developed world. Despite abundant qualitative and anecdotal evidence on its existence from around the world, there is very limited quantitative evidence on the extent of electoral fraud. We exploit random assignment of independent observers to 156 of 3,164 polling stations in the city of Moscow to estimate the effect of electoral fraud on the outcome of the Russian parliamentary elections held on December 4, 2011. We estimate the actual share of votes for the incumbent United Russia party to be at least 11 percentage points lower than the official count (36% instead of 47%). Our results suggest that the extent of the fraud was sufficient to have had a substantial impact on the outcome of the elections; they also confirm that the presence of observers is an important factor in ensuring the integrity of the procedure. PMID:23267093

Wishful thinking in the 2008 U.S. presidential election.

PubMed

Krizan, Zlatan; Miller, Jeffrey C; Johar, Omesh

2010-01-01

In elections, political preferences are strongly linked to the expectations of the electoral winner-people usually expect their favorite candidate to win. This link could be driven by wishful thinking (a biasing influence of preferences), driven by a biasing influence of expectations on one's wishes, or produced spuriously. To examine these competing possibilities in the 2008 U.S. presidential election, a longitudinal study assessed uncommitted young voters' electoral expectations and preferences over four time points during the month before the election. The findings indicated clear support for wishful thinking: Over time, people's preferences shaped their expectations, but the reverse was not the case. Moreover, these relations were larger among those more strongly identified with their political party and held even when perceptions of general candidate popularity were taken into account. Finally, changes in electoral expectations were consequential, as they shaped disappointment in the electoral results even after taking candidate preferences into account.

Citizenship rights for immigrants: national political processes and cross-national convergence in western Europe, 1980-2008.

PubMed

Koopmans, Ruud; Michalowski, Ines; Waibel, Stine

2012-01-01

Immigrant citizenship rights in the nation-state reference both theories of cross-national convergence and the resilience of national political processes. This article investigates European countries' attribution of rights to immigrants: Have these rights become more inclusive and more similar across countries? Are they affected by EU membership, the role of the judiciary, the party in power, the size of the immigrant electorate, or pressure exerted by anti-immigrant parties? Original data on 10 European countries, 1980-2008, reveal no evidence for cross-national convergence. Rights tended to become more inclusive until 2002, but stagnated afterward. Electoral changes drive these trends: growth of the immigrant electorate led to expansion, but countermobilization by right-wing parties slowed or reversed liberalizations. These electoral mechanisms are in turn shaped by long-standing policy traditions, leading to strong path dependence and the reproduction of preexisting cross-national differences.

Device for modular input high-speed multi-channel digitizing of electrical data

DOEpatents

VanDeusen, Alan L.; Crist, Charles E.

1995-09-26

A multi-channel high-speed digitizer module converts a plurality of analog signals to digital signals (digitizing) and stores the signals in a memory device. The analog input channels are digitized simultaneously at high speed with a relatively large number of on-board memory data points per channel. The module provides an automated calibration based upon a single voltage reference source. Low signal noise at such a high density and sample rate is accomplished by ensuring the A/D converters are clocked at the same point in the noise cycle each time so that synchronous noise sampling occurs. This sampling process, in conjunction with an automated calibration, yields signal noise levels well below the noise level present on the analog reference voltages.

Modelling and simulation of current fed dc to dc converter for PHEV applications using renewable source

NASA Astrophysics Data System (ADS)

Milind Metha, Manish; Tutki, Sanjay; Rajan, Aju; Elangovan, D.; Arunkumar, G.

2017-11-01

With the current rate of depletion of the fossil fuel the need to switch on to the renewable energy sources is the need of the hour. Thus the need for new and efficient converters arises so as to replace the existing less efficient diesel and petroleum IC engines with renewable energy sources. The PHEVs, which have been launched in the market, and Upcoming PHEVs have converters around 380V to 400V generated with a power range between 2KW to 2.8KW. The fundamental target of this paper is to plan a productive converter keeping in mind cost and size restriction. In this paper, a two-stage dc-dc converter is proposed. The proposed converter is utilized to venture up a voltage from 24V (photovoltaic source) to a yield voltage of 400V to take care of a power demand of 2.4kW for a plug-in hybrid electric vehicle (PHEV) application considering the real time scenario of PHEV. This paper talks about in detail why the current fed converter is utilized alongside a voltage doubler thus minimizing the transformer turns thereby reducing the overall size of the final product. Simulation results along with calculation for the duty cycle of the firing sequence for different value of transformer turns are presented for a prototype unit.

Biological cell as a soft magnetoelectric material: Elucidating the physical mechanisms underpinning the detection of magnetic fields by animals

NASA Astrophysics Data System (ADS)

Krichen, S.; Liu, L.; Sharma, P.

2017-10-01

Sharks, birds, bats, turtles, and many other animals can detect magnetic fields. Aside from using this remarkable ability to exploit the terrestrial magnetic field map to sense direction, a subset is also able to implement a version of the so-called geophysical positioning system. How do these animals detect magnetic fields? The answer to this rather deceptively simple question has proven to be quite elusive. The currently prevalent theories, while providing interesting insights, fall short of explaining several aspects of magnetoreception. For example, minute magnetic particles have been detected in magnetically sensitive animals. However, how is the detected magnetic field converted into electrical signals given any lack of experimental evidence for relevant electroreceptors? In principle, a magnetoelectric material is capable of converting magnetic signals into electricity (and vice versa). This property, however, is rare and restricted to a rather small set of exotic hard crystalline materials. Indeed, such elements have never been detected in the animals studied so far. In this work we quantitatively outline the conditions under which a biological cell may detect a magnetic field and convert it into electrical signals detectable by biological cells. Specifically, we prove the existence of an overlooked strain-mediated mechanism and show that most biological cells can act as nontrivial magnetoelectric materials provided that the magnetic permeability constant is only slightly more than that of a vacuum. The enhanced magnetic permeability is easily achieved by small amounts of magnetic particles that have been experimentally detected in magnetosensitive animals. Our proposed mechanism appears to explain most of the experimental observations related to the physical basis of magnetoreception.

A Self-Sustained Wireless Multi-Sensor Platform Integrated with Printable Organic Sensors for Indoor Environmental Monitoring

PubMed Central

Wu, Chun-Chang; Chuang, Wen-Yu; Wu, Ching-Da; Su, Yu-Cheng; Huang, Yung-Yang; Huang, Yang-Jing; Peng, Sheng-Yu; Yu, Shih-An; Lin, Chih-Ting; Lu, Shey-Shi

2017-01-01

A self-sustained multi-sensor platform for indoor environmental monitoring is proposed in this paper. To reduce the cost and power consumption of the sensing platform, in the developed platform, organic materials of PEDOT:PSS and PEDOT:PSS/EB-PANI are used as the sensing films for humidity and CO2 detection, respectively. Different from traditional gas sensors, these organic sensing films can operate at room temperature without heating processes or infrared transceivers so that the power consumption of the developed humidity and the CO2 sensors can be as low as 10 μW and 5 μW, respectively. To cooperate with these low-power sensors, a Complementary Metal-Oxide-Semiconductor (CMOS) system-on-chip (SoC) is designed to amplify and to read out multiple sensor signals with low power consumption. The developed SoC includes an analog-front-end interface circuit (AFE), an analog-to-digital convertor (ADC), a digital controller and a power management unit (PMU). Scheduled by the digital controller, the sensing circuits are power gated with a small duty-cycle to reduce the average power consumption to 3.2 μW. The designed PMU converts the power scavenged from a dye sensitized solar cell (DSSC) module into required supply voltages for SoC circuits operation under typical indoor illuminance conditions. To our knowledge, this is the first multiple environmental parameters (Temperature/CO2/Humidity) sensing platform that demonstrates a true self-powering functionality for long-term operations. PMID:28353680

Double C-H activation of ethane by metal-free SO2*+ radical cations.

PubMed

de Petris, Giulia; Cartoni, Antonella; Troiani, Anna; Barone, Vincenzo; Cimino, Paola; Angelini, Giancarlo; Ursini, Ornella

2010-06-01

The room-temperature C-H activation of ethane by metal-free SO(2)(*+) radical cations has been investigated under different pressure regimes by mass spectrometric techniques. The major reaction channel is the conversion of ethane to ethylene accompanied by the formation of H(2)SO(2)(*+), the radical cation of sulfoxylic acid. The mechanism of the double C-H activation, in the absence of the single activation product HSO(2)(+), is elucidated by kinetic studies and quantum chemical calculations. Under near single-collision conditions the reaction occurs with rate constant k=1.0 x 10(-9) (+/-30%) cm(3) s(-1) molecule(-1), efficiency=90%, kinetic isotope effect k(H)/k(D)=1.1, and partial H/D scrambling. The theoretical analysis shows that the interaction of SO(2)(*+) with ethane through an oxygen atom directly leads to the C-H activation intermediate. The interaction through sulfur leads to an encounter complex that rapidly converts to the same intermediate. The double C-H activation occurs by a reaction path that lies below the reactants and involves intermediates separated by very low energy barriers, which include a complex of the ethyl cation suitable to undergo H/D scrambling. Key issues in the observed reactivity are electron-transfer processes, in which a crucial role is played by geometrical constraints. The work shows how mechanistic details disclosed by the reactions of metal-free electrophiles may contribute to the current understanding of the C-H activation of ethane.

A Self-Sustained Wireless Multi-Sensor Platform Integrated with Printable Organic Sensors for Indoor Environmental Monitoring.

PubMed

Wu, Chun-Chang; Chuang, Wen-Yu; Wu, Ching-Da; Su, Yu-Cheng; Huang, Yung-Yang; Huang, Yang-Jing; Peng, Sheng-Yu; Yu, Shih-An; Lin, Chih-Ting; Lu, Shey-Shi

2017-03-29

A self-sustained multi-sensor platform for indoor environmental monitoring is proposed in this paper. To reduce the cost and power consumption of the sensing platform, in the developed platform, organic materials of PEDOT:PSS and PEDOT:PSS/EB-PANI are used as the sensing films for humidity and CO₂ detection, respectively. Different from traditional gas sensors, these organic sensing films can operate at room temperature without heating processes or infrared transceivers so that the power consumption of the developed humidity and the CO₂ sensors can be as low as 10 μW and 5 μW, respectively. To cooperate with these low-power sensors, a Complementary Metal-Oxide-Semiconductor (CMOS) system-on-chip (SoC) is designed to amplify and to read out multiple sensor signals with low power consumption. The developed SoC includes an analog-front-end interface circuit (AFE), an analog-to-digital convertor (ADC), a digital controller and a power management unit (PMU). Scheduled by the digital controller, the sensing circuits are power gated with a small duty-cycle to reduce the average power consumption to 3.2 μW. The designed PMU converts the power scavenged from a dye sensitized solar cell (DSSC) module into required supply voltages for SoC circuits operation under typical indoor illuminance conditions. To our knowledge, this is the first multiple environmental parameters (Temperature/CO₂/Humidity) sensing platform that demonstrates a true self-powering functionality for long-term operations.

Esterification of oil adsorbed on palm decanter cake into methyl ester using sulfonated rice husk ash as heterogeneous acid catalyst

NASA Astrophysics Data System (ADS)

Hindryawati, Noor; Erwin, Maniam, Gaanty Pragas

2017-02-01

Palm Decanter cake (PDC) which is categorized as the waste from palm oil mill has been found to contain residual crude palm oil. The oil adsorbed on the PDC (PDC-oil) can be extracted and potentially used as feedstock for biodiesel production. Feedstock from waste like PDC-oil is burdened with high free fatty acids (FFAs) which make the feedstock difficult to be converted into biodiesel using basic catalyst. Therefore, in this study, a solid acid, RHA-SO3H catalyst was synthesized by sulfonating rice husk ash (RHA) with concentrated sulfuric acid. The RHA-SO3H prepared was characterized with TGA, FTIR, BET, XRD, FE-SEM, and Hammett indicators (methyl red, bromophenol blue, and crystal violet). PDC was found to have about 11.3 wt. % oil recovered after 1 hour extraction using ultrasound method. The presence of sulfonate group was observed in IR spectrum, and the surface area of RHA-SO3H was reduced to 37 m2.g-1 after impregnation of sulfonate group. The RHA-SO3H catalyst showed that it can work for both esterification of free fatty acid which is present in PDC-oil, and transesterification of triglycerides into methyl ester. The results showed highest methyl ester content of 70.2 wt.% at optimal conditions, which was 6 wt.% catalyst amount, methanol to oil molar ratio of 17:1 for 5 hours at 120 °C.

The best news for LPG in Denmark is diesel conversion breakthrough

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Throughout Scandanavia, taxes seem to drive the marketplace. Governments do not want to encourage consumption of alcoholic beverages, so they tax them heavily, thereby actually discouraging their use. Using the same means, they dictate the fate of the various fuels. Taxes have depressed propane's use to a large extent; today it is priced at three times natural gas, with the result that it accounts for only 0.5%-0.7% of total energy consumption. But, this paper reports on a potential new star that has appeared on the horizon, as participants in the People-to-People sojourn to Scandanavia last August learned. It's a programmore » of converting diesel buses to propane, and officials of the company that is marketing it, Skibby Motor A/S, are so confident of its success that they have already begun a campaign of introducing it to the U.S.« less

Flame Imaging System

NASA Technical Reports Server (NTRS)

Barnes, Heidi L. (Inventor); Smith, Harvey S. (Inventor)

1998-01-01

A system for imaging a flame and the background scene is discussed. The flame imaging system consists of two charge-coupled-device (CCD) cameras. One camera uses a 800 nm long pass filter which during overcast conditions blocks sufficient background light so the hydrogen flame is brighter than the background light, and the second CCD camera uses a 1100 nm long pass filter, which blocks the solar background in full sunshine conditions such that the hydrogen flame is brighter than the solar background. Two electronic viewfinders convert the signal from the cameras into a visible image. The operator can select the appropriate filtered camera to use depending on the current light conditions. In addition, a narrow band pass filtered InGaAs sensor at 1360 nm triggers an audible alarm and a flashing LED if the sensor detects a flame, providing additional flame detection so the operator does not overlook a small flame.

Extraction of Molybdenum from Molybdenite Concentrates with Hydrometallurgical Processing

NASA Astrophysics Data System (ADS)

Jiang, Kaixi; Wang, Yufang; Zou, Xiaoping; Zhang, Lei; Liu, Sanping

2012-11-01

Molybdenite concentrates are usually treated by roasting, but low-concentration SO2 pollution is an associated problem. A hydrometallurgical process with pressure oxidation leaching (POX) and solvent extraction (SX) was developed in recent years. During POX, the oxidation of molybdenum (Mo) is above 98%. More than 95% of the rhenium (Re) and 15% to 20% of the Mo are leached into solution. The sulfur in the concentrate is converted to H2SO4, which results in high acidity of the solution. SX was used to recover the Re and Mo from the solution. The extraction of Re and Mo were above 98%. The loaded organic reagent is stripped with ammonia. More than 98% of the Mo can be stripped from the organic phase. Compared with the roasting process, the total recovery of Mo increased from 93% to 97% and that of Re from 60% to 90% when POX and SX are utilized.

Time-response shaping using output to input saturation transformation

NASA Astrophysics Data System (ADS)

Chambon, E.; Burlion, L.; Apkarian, P.

2018-03-01

For linear systems, the control law design is often performed so that the resulting closed loop meets specific frequency-domain requirements. However, in many cases, it may be observed that the obtained controller does not enforce time-domain requirements amongst which the objective of keeping a scalar output variable in a given interval. In this article, a transformation is proposed to convert prescribed bounds on an output variable into time-varying saturations on the synthesised linear scalar control law. This transformation uses some well-chosen time-varying coefficients so that the resulting time-varying saturation bounds do not overlap in the presence of disturbances. Using an anti-windup approach, it is obtained that the origin of the resulting closed loop is globally asymptotically stable and that the constrained output variable satisfies the time-domain constraints in the presence of an unknown finite-energy-bounded disturbance. An application to a linear ball and beam model is presented.

Ammonia Vapor-Assisted Synthesis of Cu(OH)2 and CuO Nanostructures: Anionic (Cl-, NO3 -, SO4 2-) Influence on the Product Morphology

NASA Astrophysics Data System (ADS)

Mansournia, Mohammadreza; Arbabi, Akram

2017-01-01

Shape control of inorganic nanostructures generally requires using surfactants or ligands to passivate certain crystallographic planes. This paper describes a novel additive-free synthesis of cupric oxide nanostructures with different morphologies from the aqueous solutions of copper(II) with Cl-, NO3 -, and SO4 2- as counter ions. Through a one-step approach, CuO nanoleaves, nanoparticles and flower-like microspheres were directly synthesized at 80°C upon exposure to ammonia vapor using a cupric solution as a single precursor. Furthermore, during a two-step process, Cu(OH)2 nanofibers and nanorods were prepared under an ammonia atmosphere, then converted to CuO nanostructures with morphology preservation by heat treatment in air. The as-prepared Cu(OH)2 and CuO nanostructures are characterized using x-ray diffraction, scanning electron microscopy and Fourier transformation infrared spectroscopy techniques.

Comparative Elections: Building a Basic Reference Collection.

ERIC Educational Resources Information Center

Nalen, James E.

2001-01-01

This annotated bibliography focuses on resources for the study of international elections and electoral systems and outcomes that will be useful for collection development and for answering reference questions about foreign elections. Discusses comparative politics, comparative elections, and possible electoral reform. (LRW)

Using the theory of planned behaviour to develop targets for interventions to enhance patient communication during pharmacy consultations for non-prescription medicines.

PubMed

Watson, Margaret C; Johnston, Marie; Entwistle, Vikki; Lee, Amanda J; Bond, Christine M; Fielding, Shona

2014-12-01

To identify modifiable factors that influence patients' information-giving behaviour about their health during consultations with pharmacy staff. A theory of planned behaviour questionnaire was posted to 3000 individuals randomly selected from the Scottish Electoral Register. The 927 respondents confirmed a low rate of disclosure of information about their health to pharmacy staff during their last pharmacy visit. Individuals who intended to give information about their health during pharmacy consultations were more likely to do so. Those who intended to give information during consultations had higher subjective norms than those who did not (i.e. intentions were associated with beliefs that people who were important to them, e.g. family members, doctors, thought they should give information during these consultations). Control beliefs, e.g. 'I am confident that I will give information if I have received good advice in the past', and behavioural beliefs, e.g. 'If I give information I will be sold an appropriate medicine', were not associated with intention or behaviour. Future interventions to promote relevant communication between patients and pharmacy staff should target patients' subjective norms rather than control beliefs or behavioural beliefs. © 2014 Royal Pharmaceutical Society.

REACTOR-FLASH BOILER-FLYWHEEL POWER PLANT

DOEpatents

Loeb, E.

1961-01-17

A power generator in the form of a flywheel with four reactors positioned about its rim is described. The reactors are so positioned that steam, produced in the reactor, exists tangentially to the flywheel, giving it a rotation. The reactors are incompletely moderated without water. The water enters the flywheel at its axis, under sufficient pressure to force it through the reactors, where it is converted to steam. The fuel consists of parallel twisted ribbons assembled to approximate a cylinder.

Laser-Induced Fluorescence and Synthetic Jet Fuel Analysis in the Ultra Compact Combustor

DTIC Science & Technology

2009-12-01

In the primary zone, high- temperature, high-pressure air enters from the compressor and flows around fuel injectors spraying atomized liquid -droplet...chemical reaction in which synthesis gas , a mixture of carbon monoxide and hydrogen, is converted into liquid hydrocarbons of various forms. The most...the fuel lines needed to be rebuilt due to a recent COAL lab renovation. The liquid fuel system had not been used for nearly two years so some

Imaging RF Phased Array Receivers using Optically-Coherent Up-conversion for High Beam-Bandwidth Processing

DTIC Science & Technology

2017-03-01

It does so by using an optical lens to perform an inverse spatial Fourier Transform on the up-converted RF signals, thereby rendering a real-time... simultaneous beams or other engineered beam patterns. There are two general approaches to array-based beam forming: digital and analog. In digital beam...of significantly limiting the number of beams that can be formed simultaneously and narrowing the operational bandwidth. An alternate approach that

Fully Converting Graphite into Graphene Oxide Hydrogels by Preoxidation with Impure Manganese Dioxide.

PubMed

Sun, Jiaojiao; Yang, Ningxin; Sun, Zhe; Zeng, Mengqi; Fu, Lei; Hu, Chengguo; Hu, Shengshui

2015-09-30

Potassium permanganate (KMnO4) has been proved to be an efficient oxidant for converting graphite into graphite oxide, but its slow diffusion in the interlayer of graphite seriously restricts the production of graphene oxide (GO). Here, we demonstrate that the preoxidation of graphite by impure manganese dioxide (MnO2) in a mixture of concentrated sulfuric acid (H2SO4) and phosphorus pentoxide (P2O5) can efficiently improve the synthesis of GO when KMnO4 is employed as the oxidant. The prepared honey-like GO hydrogels possess a high yield of single-layer sheets, large sizes (average lateral size up to 20 μm), wide ranges of stable dispersion concentrations (from dilute solutions, viscous hydrogels, to dry films), and good conductivity after reduction (~2.9 × 10(4) S/m). The mechanism for the improved synthesis of GO by impure MnO2 was explored. The enhanced exfoliation and oxidation of graphite by oxidative Mn ions (mainly Mn(3+)), which are synergistically produced by the reaction of impure MnO2 with H2SO4 and P2O5, are found to be responsible for the improved synthesis of such GO hydrogels. Particularly, preoxidized graphite (POG) can be partially dispersed in water with sonication, which allows the facile construction of flexible and highly conductive graphene nanosheet film electrodes with excellent electrochemical sensing properties.

Research on precise pneumatic-electric displacement sensor with large measurement range

NASA Astrophysics Data System (ADS)

Yin, Zhehao; Yuan, Yibao; Liu, Baoshuai

2017-10-01

This research mainly focuses on precise pneumatic-electric displacement sensor which has large measurement range. Under the high precision, measurement range can be expanded so that the need of high precision as well as large range can be satisfied in the field of machining inspection technology. This research was started by the analysis of pneumatic-measuring theory. Then, an gas circuit measuring system which is based on differential pressure was designed. This designed system can reach two aims: Firstly, to convert displacement signal into gas signal; Secondly, to reduce the measurement error which caused by pressure and environmental turbulence. Furthermore, in consideration of the high requirement for linearity, sensitivity and stability, the project studied the pneumatic-electric transducer which puts the SCX series pressure sensor as a key part. The main purpose of this pneumatic-electric transducer is to convert gas signal to suitable electrical signal. Lastly, a broken line subsection linearization circuit was designed, which can nonlinear correct the output characteristic curve so as to enlarge the linear measurement range. The final result could be briefly described like this: under the condition that measuring error is less than 1μm, measurement range could be extended to approximately 200μm which is much higher than the measurement range of traditional pneumatic measuring instrument. Meanwhile, it can reach higher exchangeability and stability in order to become more suitable to engineering application.

Mini Solar and Sea Current Power Generation System

NASA Astrophysics Data System (ADS)

Almenhali, Abdulrahman; Alshamsi, Hatem; Aljunaibi, Yaser; Almussabi, Dheyab; Alshehhi, Ahmed; Hilal, Hassan Bu

2017-07-01

The power demand in United Arab Emirates is increased so that there is a consistent power cut in our region. This is because of high power consumption by factories and also due to less availability of conventional energy resources. Electricity is most needed facility for the human being. All the conventional energy resources are depleting day by day. So we have to shift from conventional to non-conventional energy resources. In this the combination of two energy resources is takes place i.e. wind and solar energy. This process reviles the sustainable energy resources without damaging the nature. We can give uninterrupted power by using hybrid energy system. Basically this system involves the integration of two energy system that will give continuous power. Solar panels are used for converting solar energy and wind turbines are used for converting wind energy into electricity. This electrical power can utilize for various purpose. Generation of electricity will be takes place at affordable cost. This paper deals with the generation of electricity by using two sources combine which leads to generate electricity with affordable cost without damaging the nature balance. The purpose of this project was to design a portable and low cost power system that combines both sea current electric turbine and solar electric technologies. This system will be designed in efforts to develop a power solution for remote locations or use it as another source of green power.

Underwater Noise from a Wave Energy Converter Is Unlikely to Affect Marine Mammals

PubMed Central

Tougaard, Jakob

2015-01-01

Underwater noise was recorded from the Wavestar wave energy converter; a full-scale hydraulic point absorber, placed on a jack-up rig on the Danish North Sea coast. Noise was recorded 25 m from the converter with an autonomous recording unit (10 Hz to 20 kHz bandwidth). Median sound pressure levels (Leq) in third-octave bands during operation of the converter were 106–109 dB re. 1 μPa in the range 125–250 Hz, 1–2 dB above ambient noise levels (statistically significant). Outside the range 125–250 Hz the noise from the converter was undetectable above the ambient noise. During start and stop of the converter a more powerful tone at 150 Hz (sound pressure level (Leq) 121–125 dB re 1 μPa) was easily detectable. This tone likely originated from the hydraulic pump which was used to lower the absorbers into the water and lift them out of the water at shutdown. Noise levels from the operating wave converter were so low that they would barely be audible to marine mammals and the likelihood of negative impact from the noise appears minimal. A likely explanation for the low noise emissions is the construction of the converter where all moving parts, except for the absorbers themselves, are placed above water on a jack-up rig. The results may thus not be directly transferable to other wave converter designs but do demonstrate that it is possible to harness wave energy without noise pollution to the marine environment. PMID:26148299

Underwater Noise from a Wave Energy Converter Is Unlikely to Affect Marine Mammals.

PubMed

Tougaard, Jakob

2015-01-01

Underwater noise was recorded from the Wavestar wave energy converter; a full-scale hydraulic point absorber, placed on a jack-up rig on the Danish North Sea coast. Noise was recorded 25 m from the converter with an autonomous recording unit (10 Hz to 20 kHz bandwidth). Median sound pressure levels (Leq) in third-octave bands during operation of the converter were 106-109 dB re. 1 μPa in the range 125-250 Hz, 1-2 dB above ambient noise levels (statistically significant). Outside the range 125-250 Hz the noise from the converter was undetectable above the ambient noise. During start and stop of the converter a more powerful tone at 150 Hz (sound pressure level (Leq) 121-125 dB re 1 μPa) was easily detectable. This tone likely originated from the hydraulic pump which was used to lower the absorbers into the water and lift them out of the water at shutdown. Noise levels from the operating wave converter were so low that they would barely be audible to marine mammals and the likelihood of negative impact from the noise appears minimal. A likely explanation for the low noise emissions is the construction of the converter where all moving parts, except for the absorbers themselves, are placed above water on a jack-up rig. The results may thus not be directly transferable to other wave converter designs but do demonstrate that it is possible to harness wave energy without noise pollution to the marine environment.

Assessing Presidential Character: Degradation Rituals in Political Campaigns.

ERIC Educational Resources Information Center

Bennett, W. Lance

1981-01-01

Considers the consequences of taking political blunders seriously as central objects of electoral discourse. Explores gaffes as possible degradation rituals and as contributions to the definition of the electoral process and to the information needs of voters who must make decisions within that process. (PD)

Optical, colloidal and biological properties of up-converting nanoparticles embedded in polyester nanocarriers

NASA Astrophysics Data System (ADS)

Wawrzyńczyk, Dominika; Kulbacka, Julita; Bazylińska, Urszula

2017-08-01

We have investigated the change in optical properties and biocompatibility of up-converting NaYF4 nanoparticles (NPs) upon encapsulation inside the polyester nanocarriers (NCs) stabilized by Crempophor RH40 (CRH40), poly(D,L-lactide) (PLA), Pluronic P123 (P123). NaYF4:Er3+,Yb3+ NPs showed intense green and red emission, and upon encapsulation the increase of red band in respect to green one was observed, with no luminescence lifetime shortening. Obtained NCs showed prolonged colloidal stability and protective effect of the polymer shell simultaneously preserving the high emission efficiency of nanoparticles embedded within the silicon oil (SO) core. Based on emission spectra, kinetic measurements and cytotoxicity studies upon human malignant melanoma Me45 cell line we have shown the advantages of using polyester NCs as containers for the up-converting NPs. Due to the possibility of co-encapsulation of photosensitizers the obtained nanocarriers showed potential for application in theranostics.

Improvement of up-converting phosphor technology-based biosensor

NASA Astrophysics Data System (ADS)

Xie, Chengke; Huang, Lihua; Zhang, Youbao; Guo, Xiaoxian; Qu, Jianfeng; Huang, Huijie

2008-12-01

A novel biosensor based on up-converting phosphor technology (UPT) was developed several years ago. It is a kind of optical biosensor using up-converting phosphor (UCP) particles as the biological marker. From then on, some improvements have been made for this UPT-based biosensor. The primary aspects of the improvement lie in the control system. On one hand, the hardware of the control system has been optimized, including replacing two single chip microcomputers (SCM) with only one, the optimal design of the keyboard interface circuit and the liquid crystal module (LCM) control circuit et al.. These result in lower power consumption and higher reliability. On the other hand, a novel signal processing algorithm is proposed in this paper, which can improve the automation and operating simplicity of the UPT-based biosensor. It has proved to have high sensitivity (~ng/ml), high stability and good repeatability (CV<5%), which is better than the former system. It can meet the need of some various applications such as rapid immunoassay, chemical and biological detection and so on.

Solar power generation system for reducing leakage current

NASA Astrophysics Data System (ADS)

Wu, Jinn-Chang; Jou, Hurng-Liahng; Hung, Chih-Yi

2018-04-01

This paper proposes a transformer-less multi-level solar power generation system. This solar power generation system is composed of a solar cell array, a boost power converter, an isolation switch set and a full-bridge inverter. A unipolar pulse-width modulation (PWM) strategy is used in the full-bridge inverter to attenuate the output ripple current. Circuit isolation is accomplished by integrating the isolation switch set between the solar cell array and the utility, to suppress the leakage current. The isolation switch set also determines the DC bus voltage for the full-bridge inverter connecting to the solar cell array or the output of the boost power converter. Accordingly, the proposed transformer-less multi-level solar power generation system generates a five-level voltage, and the partial power of the solar cell array is also converted to AC power using only the full-bridge inverter, so the power efficiency is increased. A prototype is developed to validate the performance of the proposed transformer-less multi-level solar power generation system.

Displaying Composite and Archived Soundings in the Advanced Weather Interactive Processing System

NASA Technical Reports Server (NTRS)

Barrett, Joe H., III; Volkmer, Matthew R.; Blottman, Peter F.; Sharp, David W.

2008-01-01

In a previous task, the Applied Meteorology Unit (AMU) developed spatial and temporal climatologies of lightning occurrence based on eight atmospheric flow regimes. The AMU created climatological, or composite, soundings of wind speed and direction, temperature, and dew point temperature at four rawinsonde observation stations at Jacksonville, Tampa, Miami, and Cape Canaveral Air Force Station, for each of the eight flow regimes. The composite soundings were delivered to the National Weather Service (NWS) Melbourne (MLB) office for display using the National version of the Skew-T Hodograph analysis and Research Program (NSHARP) software program. The NWS MLB requested the AMU make the composite soundings available for display in the Advanced Weather Interactive Processing System (AWIPS), so they could be overlaid on current observed soundings. This will allow the forecasters to compare the current state of the atmosphere with climatology. This presentation describes how the AMU converted the composite soundings from NSHARP Archive format to Network Common Data Form (NetCDF) format, so that the soundings could be displayed in AWl PS. The NetCDF is a set of data formats, programming interfaces, and software libraries used to read and write scientific data files. In AWIPS, each meteorological data type, such as soundings or surface observations, has a unique NetCDF format. Each format is described by a NetCDF template file. Although NetCDF files are in binary format, they can be converted to a text format called network Common data form Description Language (CDL). A software utility called ncgen is used to create a NetCDF file from a CDL file, while the ncdump utility is used to create a CDL file from a NetCDF file. An AWIPS receives soundings in Binary Universal Form for the Representation of Meteorological data (BUFR) format (http://dss.ucar.edu/docs/formats/bufr/), and then decodes them into NetCDF format. Only two sounding files are generated in AWIPS per day. One file contains all of the soundings received worldwide between 0000 UTC and 1200 UTC, and the other includes all soundings between 1200 UTC and 0000 UTC. In order to add the composite soundings into AWIPS, a procedure was created to configure, or localize, AWIPS. This involved modifying and creating several configuration text files. A unique fourcharacter site identifier was created for each of the 32 soundings so each could be viewed separately. The first three characters were based on the site identifier of the observed sounding, while the last character was based on the flow regime. While researching the localization process for soundings, the AMU discovered a method of archiving soundings so old soundings would not get purged automatically by AWl PS. This method could provide an alternative way of localizing AWl PS for composite soundings. In addition, this would allow forecasters to use archived soundings in AWIPS for case studies. A test sounding file in NetCDF format was written in order to verify the correct format for soundings in AWIPS. After the file was viewed successfully in AWIPS, the AMU wrote a software program in the Tool Command Language/Tool Kit (Tcl/Tk) language to convert the 32 composite soundings from NSHARP Archive to CDL format. The ncgen utility was then used to convert the CDL file to a NetCDF file. The NetCDF file could then be read and displayed in AWIPS.

Driver circuit for solid state light sources

DOEpatents

Palmer, Fred; Denvir, Kerry; Allen, Steven

2016-02-16

A driver circuit for a light source including one or more solid state light sources, a luminaire including the same, and a method of so driving the solid state light sources are provided. The driver circuit includes a rectifier circuit that receives an alternating current (AC) input voltage and provides a rectified AC voltage. The driver circuit also includes a switching converter circuit coupled to the light source. The switching converter circuit provides a direct current (DC) output to the light source in response to the rectified AC voltage. The driver circuit also includes a mixing circuit, coupled to the light source, to switch current through at least one solid state light source of the light source in response to each of a plurality of consecutive half-waves of the rectified AC voltage.

Optoelectronic device

DOEpatents

Bonekamp, Jeffrey E.; Boven, Michelle L.; Gaston, Ryan S.

2014-09-09

The invention is an optoelectronic device comprising an active portion which converts light to electricity or converts electricity to light, the active portion having a front side for the transmittal of the light and a back side opposite from the front side, at least two electrical leads to the active portion to convey electricity to or from the active portion, an enclosure surrounding the active portion and through which the at least two electrical leads pass wherein the hermetically sealed enclosure comprises at the front side of the active portion a barrier material which allows for transmittal of light, one or more getter materials disposed so as to not impede the transmission of light to or from the active portion, and a contiguous gap pathway to the getter material which pathway is disposed between the active portion and the barrier material.

Device for modular input high-speed multi-channel digitizing of electrical data

DOEpatents

VanDeusen, A.L.; Crist, C.E.

1995-09-26

A multi-channel high-speed digitizer module converts a plurality of analog signals to digital signals (digitizing) and stores the signals in a memory device. The analog input channels are digitized simultaneously at high speed with a relatively large number of on-board memory data points per channel. The module provides an automated calibration based upon a single voltage reference source. Low signal noise at such a high density and sample rate is accomplished by ensuring the A/D converters are clocked at the same point in the noise cycle each time so that synchronous noise sampling occurs. This sampling process, in conjunction with an automated calibration, yields signal noise levels well below the noise level present on the analog reference voltages. 1 fig.

Problems associated with reaction mass actuators used in conjunction with LQG control on the Mini-Mast

NASA Technical Reports Server (NTRS)

Ghosh, D.; Montgomery, R. C.

1987-01-01

The work being done at NASA LaRC on developing control laws for the Mini-Mast experimental facility is reviewed with particular attention given to the problems associated with the stroke limit of the reaction mass actuators used in conjunction with the LQG control. An algorithm for converting the force commands of the LQG algorithm into position command for the reaction mass devices is described. It is shown that the position command can be used as an input to a local controller so that the relative position of the reaction mass would track the commanded relative position. The stabilization of the integration scheme makes it possible to avoid the position drift arising in the direct double integration method of converting force commands to position commands.

AUTOMATIC CALIBRATING SYSTEM FOR PRESSURE TRANSDUCERS

DOEpatents

Amonette, E.L.; Rodgers, G.W.

1958-01-01

An automatic system for calibrating a number of pressure transducers is described. The disclosed embodiment of the invention uses a mercurial manometer to measure the air pressure applied to the transducer. A servo system follows the top of the mercury column as the pressure is changed and operates an analog- to-digital converter This converter furnishes electrical pulses, each representing an increment of pressure change, to a reversible counterThe transducer furnishes a signal at each calibration point, causing an electric typewriter and a card-punch machine to record the pressure at the instant as indicated by the counter. Another counter keeps track of the calibration points so that a number identifying each point is recorded with the corresponding pressure. A special relay control system controls the pressure trend and programs the sequential calibration of several transducers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chinthavali, Madhu Sudhan; Onar, Omer C; Campbell, Steven L

Integrated charger topologies that have been researched so far with dc-dc converters and the charging functionality have no isolation in the system. Isolation is an important feature that is required for user interface systems that have grid connections and therefore is a major limitation that needs to be addressed along with the integrated functionality. The topology proposed in this paper is a unique and a first of its kind topology that integrates a wireless charging system and the boost converter for the traction drive system. The new topology is also compared with an on-board charger system from a commercial electricmore » vehicle (EV). The ac-dc efficiency of the proposed system is 85.05% and the specific power and power density of the onboard components is ~455 W/kg and ~302 W/ .« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chinthavali, Madhu Sudhan; Onar, Omer C; Campbell, Steven L

Integrated charger topologies that have been researched so far with dc-dc converters and the charging functionality have no isolation in the system. Isolation is an important feature that is required for user interface systems that have grid connections and therefore is a major limitation that needs to be addressed along with the integrated functionality. The topology proposed in this paper is a unique and a first of its kind topology that integrates a wireless charging system and the boost converter for the traction drive system. The new topology is also compared with an on-board charger system from a commercial electricmore » vehicle (EV). The ac-dc efficiency of the proposed system is 85.1% and the specific power and power density of the onboard components is ~455 W/kg and ~320 W/ .« less

Divided Wisconsin: Partisan Spatial Electoral Realignment

ERIC Educational Resources Information Center

Zaniewski, Kazimierz J.; Simmons, James R.

2016-01-01

When the Republican and Democratic presidential candidates head into the general election this fall, they will be courting votes from a statewide electorate that has dramatically shifted over time, mirroring the political polarization that is happening across the country. Over the last three decades, Wisconsin's political geography has evolved…

Between Order and Disorder: A ‘Weak Law’ on Recent Electoral Behavior among Urban Voters?

PubMed Central

Borghesi, Christian; Chiche, Jean; Nadal, Jean-Pierre

2012-01-01

A new viewpoint on electoral involvement is proposed from the study of the statistics of the proportions of abstentionists, blank and null, and votes according to list of choices, in a large number of national elections in different countries. Considering 11 countries without compulsory voting (Austria, Canada, Czech Republic, France, Germany, Italy, Mexico, Poland, Romania, Spain, and Switzerland), a stylized fact emerges for the most populated cities when one computes the entropy associated to the three ratios, which we call the entropy of civic involvement of the electorate. The distribution of this entropy (over all elections and countries) appears to be sharply peaked near a common value. This almost common value is typically shared since the 1970s by electorates of the most populated municipalities, and this despite the wide disparities between voting systems and types of elections. Performing different statistical analyses, we notably show that this stylized fact reveals particular correlations between the blank/null votes and abstentionists ratios. We suggest that the existence of this hidden regularity, which we propose to coin as a ‘weak law on recent electoral behavior among urban voters’, reveals an emerging collective behavioral norm characteristic of urban citizen voting behavior in modern democracies. Analyzing exceptions to the rule provides insights into the conditions under which this normative behavior can be expected to occur. PMID:22848365

Between order and disorder: a 'weak law' on recent electoral behavior among urban voters?

PubMed

Borghesi, Christian; Chiche, Jean; Nadal, Jean-Pierre

2012-01-01

A new viewpoint on electoral involvement is proposed from the study of the statistics of the proportions of abstentionists, blank and null, and votes according to list of choices, in a large number of national elections in different countries. Considering 11 countries without compulsory voting (Austria, Canada, Czech Republic, France, Germany, Italy, Mexico, Poland, Romania, Spain, and Switzerland), a stylized fact emerges for the most populated cities when one computes the entropy associated to the three ratios, which we call the entropy of civic involvement of the electorate. The distribution of this entropy (over all elections and countries) appears to be sharply peaked near a common value. This almost common value is typically shared since the 1970s by electorates of the most populated municipalities, and this despite the wide disparities between voting systems and types of elections. Performing different statistical analyses, we notably show that this stylized fact reveals particular correlations between the blank/null votes and abstentionists ratios. We suggest that the existence of this hidden regularity, which we propose to coin as a 'weak law on recent electoral behavior among urban voters', reveals an emerging collective behavioral norm characteristic of urban citizen voting behavior in modern democracies. Analyzing exceptions to the rule provides insights into the conditions under which this normative behavior can be expected to occur.

SEMICONDUCTOR INTEGRATED CIRCUITS: A high performance 90 nm CMOS SAR ADC with hybrid architecture

NASA Astrophysics Data System (ADS)

Xingyuan, Tong; Jianming, Chen; Zhangming, Zhu; Yintang, Yang

2010-01-01

A 10-bit 2.5 MS/s SAR A/D converter is presented. In the circuit design, an R-C hybrid architecture D/A converter, pseudo-differential comparison architecture and low power voltage level shifters are utilized. Design challenges and considerations are also discussed. In the layout design, each unit resistor is sided by dummies for good matching performance, and the capacitors are routed with a common-central symmetry method to reduce the nonlin-earity error. This proposed converter is implemented based on 90 nm CMOS logic process. With a 3.3 V analog supply and a 1.0 V digital supply, the differential and integral nonlinearity are measured to be less than 0.36 LSB and 0.69 LSB respectively. With an input frequency of 1.2 MHz at 2.5 MS/s sampling rate, the SFDR and ENOB are measured to be 72.86 dB and 9.43 bits respectively, and the power dissipation is measured to be 6.62 mW including the output drivers. This SAR A/D converter occupies an area of 238 × 214 μm2. The design results of this converter show that it is suitable for multi-supply embedded SoC applications.

Load-Dependent Soft-Switching Method of Half-Bridge Current Doubler for High-Voltage Point-of-Load Converter in Data Center Power Supplies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cui, Yutian; Yang, Fei; Tolbert, Leon M.

With the increased cloud computing and digital information storage, the energy requirement of data centers keeps increasing. A high-voltage point of load (HV POL) with an input series output parallel structure is proposed to convert 400 to 1 VDC within a single stage to increase the power conversion efficiency. The symmetrical controlled half-bridge current doubler is selected as the converter topology in the HV POL. A load-dependent soft-switching method has been proposed with an auxiliary circuit that includes inductor, diode, and MOSFETs so that the hard-switching issue of typical symmetrical controlled half-bridge converters is resolved. The operation principles of themore » proposed soft-switching half-bridge current doubler have been analyzed in detail. Then, the necessity of adjusting the timing with the loading in the proposed method is analyzed based on losses, and a controller is designed to realize the load-dependent operation. A lossless RCD current sensing method is used to sense the output inductor current value in the proposed load-dependent operation. In conclusion, experimental efficiency of a hardware prototype is provided to show that the proposed method can increase the converter's efficiency in both heavy- and light-load conditions.« less

Load-Dependent Soft-Switching Method of Half-Bridge Current Doubler for High-Voltage Point-of-Load Converter in Data Center Power Supplies

DOE PAGES

Cui, Yutian; Yang, Fei; Tolbert, Leon M.; ...

2016-06-14

With the increased cloud computing and digital information storage, the energy requirement of data centers keeps increasing. A high-voltage point of load (HV POL) with an input series output parallel structure is proposed to convert 400 to 1 VDC within a single stage to increase the power conversion efficiency. The symmetrical controlled half-bridge current doubler is selected as the converter topology in the HV POL. A load-dependent soft-switching method has been proposed with an auxiliary circuit that includes inductor, diode, and MOSFETs so that the hard-switching issue of typical symmetrical controlled half-bridge converters is resolved. The operation principles of themore » proposed soft-switching half-bridge current doubler have been analyzed in detail. Then, the necessity of adjusting the timing with the loading in the proposed method is analyzed based on losses, and a controller is designed to realize the load-dependent operation. A lossless RCD current sensing method is used to sense the output inductor current value in the proposed load-dependent operation. In conclusion, experimental efficiency of a hardware prototype is provided to show that the proposed method can increase the converter's efficiency in both heavy- and light-load conditions.« less

Emission characteristics of nitrogen- and sulfur-containing odorous compounds during different sewage sludge chemical conditioning processes.

PubMed

Liu, Huan; Luo, Guang-Qian; Hu, Hong-Yun; Zhang, Qiang; Yang, Jia-Kuan; Yao, Hong

2012-10-15

Chemical conditioners are often used to enhance sewage sludge dewaterability through altering sludge properties and flocs structure, both affect odorous compounds emissions not only during sludge conditioning but also in subsequent sludge disposal. This study was to investigate emission characteristics of ammonia (NH(3)), sulfur dioxide (SO(2)), hydrogen sulfide (H(2)S) and carbonyl sulfide (COS) generated from sewage sludge conditioned by three representative conditioners, i.e., organic polymers, iron salts and skeleton builders, F-S (Fenton's reagent and skeleton builders) composite conditioner. The results demonstrate that polyacrylamide (PAM) has an insignificant effect on emission characteristics of nitrogen- and sulfur-containing odorous compounds, because the properties, sulfur and nitrogen speciations are similar in PAM-conditioned sludge and raw sludge (RS). Significant increases of SO(2) and H(2)S emissions in the H(2)SO(4) conditioning process were observed due to the accelerated decomposition of sulfur-containing amino acids in acidic environment. Fenton peroxidation facilitates the formation of COS. CaO can reduce sulfur-containing gases emission via generation of calcium sulfate. However, under strong alkaline conditions, free ammonia or protonated amine in sludge can be easily converted to volatile ammonia, resulting in a significant release of NH(3). Copyright © 2012 Elsevier B.V. All rights reserved.

DB Riley-low emission boiler system (LEBS): Superior power for the 21st century

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beittel, R.; Ruth, L.A.

1997-12-31

In conjunction with the US Department of Energy, DB Riley, Inc., is developing a highly advanced coal-fired power-generation plant called the Low Emission Boiler Systems (LEBS). By the year 2000, LEBS will provide the US electric power industry with a reliable, efficient, cost-effective, environmentally superior alternative to current technologies. LEBS incorporates significant advances in coal combustion, supercritical steam boiler design, environmental control, and materials development. The system will include a state-of-the-art steam cycle operating at supercritical steam conditions; a slagging combustor that produces vitrified ash by-products; low nitrogen oxide (NOx) burners; a new, dry, regenerable flue gas cleanup system (coppermore » oxide process) for simultaneously capturing sulfur dioxide (SO{sub 2}) and nitrogen oxides (NOx); a pulse-jet fabric filter for particulate capture; and a low-temperature heat-recovery system. The copper oxide flue gas cleanup system, which has been under development at DOE`s Pittsburgh field center, removes over 98% of SO{sub 2} and 95% of NOx from flue gas. A new moving-bed design provides efficient sorbent utilization that lowers the cleanup process cost. The captured SO{sub 2} can be converted to valuable by-products such as sulfuric acid and/or element sulfur, and the process generates no waste.« less

An RFID tag system-on-chip with wireless ECG monitoring for intelligent healthcare systems.

PubMed

Wang, Cheng-Pin; Lee, Shuenn-Yuh; Lai, Wei-Chih

2013-01-01

This paper presents a low-power wireless ECG acquisition system-on-chip (SoC), including an RF front-end circuit, a power unit, an analog front-end circuit, and a digital circuitry. The proposed RF front-end circuit can provide the amplitude shift keying demodulation and distance to digital conversion to accurately receive the data from the reader. The received data will wake up the power unit to provide the required supply voltages of analog front-end (AFE) and digital circuitry. The AFE, including a pre-amplifier, an analog filter, a post-amplifier, and an analog-to-digital converter, is used for the ECG acquisition. Moreover, the EPC Class I Gen 2 UHF standard is employed in the digital circuitry for the handshaking of communication and the control of the system. The proposed SoC has been implemented in 0.18-µm standard CMOS process and the measured results reveal the communication is compatible to the RFID protocol. The average power consumption for the operating chip is 12 µW. Using a Sony PR44 battery to the supply power (605mAh@1.4V), the RFID tag SoC operates continuously for about 50,000 hours (>5 years), which is appropriate for wireless wearable ECG monitoring systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Canavan, G.H.

This note studies the impact of maximizing the stability index rather than minimizing the first strike cost in choosing offensive missile allocations. It does so in the context of a model in which exchanges between vulnerable missile forces are modeled probabilistically, converted into first and second strike costs through approximations to the value target sets at risk, and the stability index is taken to be their ratio. The value of the allocation that minimizes the first strike cost for both attack preferences are derived analytically. The former recovers results derived earlier. The latter leads to an optimum at unity allocationmore » for which the stability index is determined analytically. For values of the attack preference greater than about unity, maximizing the stability index increases the cost of striking first 10--15%. For smaller values of the attack preference, maximizing the index increases the second strike cost a similar amount. Both are stabilizing, so if both sides could be trusted to target on missiles in order to minimize damage to value and maximize stability, the stability index for vulnerable missiles could be increased by about 15%. However, that would increase the cost to the first striker by about 15%. It is unclear why--having decided to strike--he would do so in a way that would increase damage to himself.« less

Millimeter-wave optical double resonance schemes for rapid assignment of perturbed spectra, with applications to the C{sup ~} {sup 1}B{sub 2} state of SO{sub 2}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, G. Barratt, E-mail: barratt@mit.edu, E-mail: barratt.park@gmail.com; Womack, Caroline C.; Jiang, Jun

2015-04-14

Millimeter-wave detected, millimeter-wave optical double resonance (mmODR) spectroscopy is a powerful tool for the analysis of dense, complicated regions in the optical spectra of small molecules. The availability of cavity-free microwave and millimeter wave spectrometers with frequency-agile generation and detection of radiation (required for chirped-pulse Fourier-transform spectroscopy) opens up new schemes for double resonance experiments. We demonstrate a multiplexed population labeling scheme for rapid acquisition of double resonance spectra, probing multiple rotational transitions simultaneously. We also demonstrate a millimeter-wave implementation of the coherence-converted population transfer scheme for background-free mmODR, which provides a ∼10-fold sensitivity improvement over the population labeling scheme.more » We analyze perturbations in the C{sup ~} state of SO{sub 2}, and we rotationally assign a b{sub 2} vibrational level at 45 328 cm{sup −1} that borrows intensity via a c-axis Coriolis interaction. We also demonstrate the effectiveness of our multiplexed mmODR scheme for rapid acquisition and assignment of three predissociated vibrational levels of the C{sup ~} state of SO{sub 2} between 46 800 and 47 650 cm{sup −1}.« less

Photogrammetry of the Viking-Lander imagery.

USGS Publications Warehouse

Wu, S.S.C.; Schafer, F.J.

1982-01-01

We have solved the problem of photogrammetric mapping from the Viking Lander photography in two ways: 1) by converting the azimuth and elevation scanning imagery to the equivalent of a frame picture by means of computerized rectification; and 2) by interfacing a high-speed, general-purpose computer to the AS-11A analytical plotter so that all computations of corrections can be performed in real time during the process of model orientation and map compilation. Examples are presented of photographs and maps of Earth and Mars. -from Authors

Perturbation Solutions for Variable Energy Blast Waves.

DTIC Science & Technology

1976-08-01

SUPPLEMENTARY NOTES The findings in this report are not to be construed as an official Department of the Army position, unless so designated by other...over that of the same volume of undisturbed gas is Converting to non-dimensional form, using Equation (2.12) and letting a prime designate D/3m... designating the integral J after Sakurai1 this becomes Ea J . — - b p0R a+l y (2.20) If the total energy behind the shock varies as a

Suppression of Interchannel Interference in FM Receivers

DTIC Science & Technology

1979-07-01

construed as an official Depart- ment of the Army position, unlessa so designated by other authorized docum ents. 19. KE£Y WORiZS (Centinae an toeva side...receiver structure is derived. Then, experimental results on a detector designed by copying the topology of the optimum receiver structure are...and autocorrelation Rm (T) and R (T). We designate t xl(t) = J rl(u) du (2) -t Xz(t) m n(u)du (3) This converts the FM waves s1(t) and s,(t) into

Bioequivalence of azathioprine products.

PubMed

Baker, Daniel E

2003-01-01

All azathioprine oral tablets are considered bioequivalent by the Food and Drug Administration based on traditional testing. However, since these tests were conducted, it has been determined that some patients have a deficiency of the enzyme most responsible for the metabolism of 6-mercaptopurine-thiopurine methyltransferase (TPMT). Azathioprine is rapidly converted to 6-mercaptopurine, its active metabolite. So it is possible that differences in TPMT activity may influence the bioequivalence of azathioprine products among individuals, especially those patients deficient in TPMT enzyme activity. However, this possibility has not been evaluated.

Observational viability and stability of nonlocal cosmology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deser, S.; Woodard, R.P., E-mail: deser@brandeis.edu, E-mail: woodard@phys.ufl.edu

2013-11-01

We show that the nonlocal gravity models, proposed to explain current cosmic acceleration without dark energy, pass two essential tests: first, they can be defined so as not to alter the, observationally correct, general relativity predictions for gravitationally bound systems. Second, they are stable, ghost-free, with no additional excitations beyond those of general relativity. In this they differ from their, ghostful, localized versions. The systems' initial value constraints are the same as in general relativity, and our nonlocal modifications never convert the original gravitons into ghosts.

Wideband Holographic Digital Recording and Reproduction. Phase IV.

DTIC Science & Technology

1980-02-01

array of 128 acousto-optic ele- meats. The electrical energy is converted to acoustic waves within a glass crystal, so that when the light passes through...systems. An AO device is a block of transparent material (various types of glass , for example) through which we pass the laser beam that we want to...Clearance - .60 mm from cell Vignetting None None Glass Type Optional SF6 R ecord Mode Input Aperture 14 mm x 52mm 14mrm x 52rm Field Angle +12. 0

The Politics of the League of Women Voters.

ERIC Educational Resources Information Center

Black, Naomi

1983-01-01

The League of Women Voters is often regarded as having retarded the participation of women in American electoral politics because of its nonpartisan stance. However, many League members have used the League as an entry into electoral politics, and the League has supported many issues important to women. (IS)

Building Alliances: Defending Immigrant Rights in Rural Oregon

ERIC Educational Resources Information Center

Stephen, Lynn

2008-01-01

Political participation in the rural United States has often been narrowly defined within the confines of electoral politics. Increasingly, participants in rural US social movements have highlighted the shortcomings of democracy defined purely in terms of electoral politics in favour of a more participatory model of politics that focuses on the…

One Vote for the Electoral College

ERIC Educational Resources Information Center

Turner, John J., Jr.

2007-01-01

For students of history, the acrimonious and contentious 1876 presidential canvass came to mind during the 2000 election imbroglio. Democrat Samuel J. Tilden won the popular vote, but to the dismay of outraged Democrats, an electoral commission of eight Republicans and seven Democrats decided along strict party lines to give twenty disputed…

Political Education Manual.

ERIC Educational Resources Information Center

League of United Latin American Citizens, Washington, DC.

Written to help Hispanics understand the electoral process more thoroughly and to encourage them to participate more actively in the political arena, this manual begins by describing the present status of the Hispanic electorate and then explains how laws are made, how Hispanics can influence legislation, and how to organize a voter registration…

26 CFR 1.271-1 - Debts owed by political parties.

Code of Federal Regulations, 2014 CFR

2014-04-01

...-presidential electors, or the selection, nomination, or election of any individual to any Federal, State, or local elective public office, whether or not such individual or electors are selected, nominated, or elected. Accordingly, a political party includes a committee or other group which accepts contributions or...

26 CFR 1.271-1 - Debts owed by political parties.

Code of Federal Regulations, 2012 CFR

2012-04-01

...-presidential electors, or the selection, nomination, or election of any individual to any Federal, State, or local elective public office, whether or not such individual or electors are selected, nominated, or elected. Accordingly, a political party includes a committee or other group which accepts contributions or...

26 CFR 1.271-1 - Debts owed by political parties.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-presidential electors, or the selection, nomination, or election of any individual to any Federal, State, or local elective public office, whether or not such individual or electors are selected, nominated, or elected. Accordingly, a political party includes a committee or other group which accepts contributions or...

26 CFR 1.271-1 - Debts owed by political parties.

Code of Federal Regulations, 2010 CFR

2010-04-01

...-presidential electors, or the selection, nomination, or election of any individual to any Federal, State, or local elective public office, whether or not such individual or electors are selected, nominated, or elected. Accordingly, a political party includes a committee or other group which accepts contributions or...

26 CFR 1.271-1 - Debts owed by political parties.

Code of Federal Regulations, 2013 CFR

2013-04-01

...-presidential electors, or the selection, nomination, or election of any individual to any Federal, State, or local elective public office, whether or not such individual or electors are selected, nominated, or elected. Accordingly, a political party includes a committee or other group which accepts contributions or...

Vote. Election Program.

ERIC Educational Resources Information Center

Illinois State Board of Education, Springfield.

This election-education program is designed to help develop an informed electorate and to instill in future voters an appreciation of the importance of the right to vote. It provides a framework for discussions of the electoral process and gives students an opportunity to face the responsibilities and challenges associated with citizenship and…

A Foreign Correspondent's View of the Electoral Process.

ERIC Educational Resources Information Center

Gardner, Mary A. Ed.

According to their personal points of view regarding United States politics, a panel of foreign correspondents from other nations evaluated the United States electoral process and discussed the difficulties involved in conveying the complexities of this process to an audience. This document contains an edited transcript of the panel's comments.…

Voting and the Disabled: A Review of Canadian Election Legislation.

ERIC Educational Resources Information Center

Curtis, Charles K.

1983-01-01

Examination of Election Acts to determine how disabled electors are accommodated during federal, provincial, and municipal elections in Canada revealed that, beyond identifying procedures for accommodating electors with certain disabilities, in more jurisdictions both severely retarded and mentally ill persons are denied the right to vote.…

The Revolutionary Left and Terrorist Violence in Chile.

DTIC Science & Technology

1986-06-01

Fraude Electoral Designada por la Facultad de Derecho de la Pontifica Universidad de Chile," in Libro Blanco del Cambio de Gobierno de Chile, Editorial...Chilean law, could not be invaded by the police. The MIR never became a formal political party. It completely rejected the electoral process

Online analysis of H2S and SO2 via advanced mid-infrared gas sensors.

PubMed

Petruci, João Flavio da Silveira; Wilk, Andreas; Cardoso, Arnaldo Alves; Mizaikoff, Boris

2015-10-06

Volatile sulfur compounds (VSCs) are among the most prevalent emitted pollutants in urban and rural atmospheres. Mainly because of the versatility of sulfur regarding its oxidation state (2- to 6+), VSCs are present in a wide variety of redox-environments, concentration levels, and molar ratios. Among the VSCs, hydrogen sulfide and sulfur dioxide are considered most relevant and have simultaneously been detected within naturally and anthropogenically caused emission events (e.g., volcano emissions, food production and industries, coal pyrolysis, and various biological activities). Next to their presence as pollutants, changes within their molar ratio may also indicate natural anomalies. Prior to analysis, H2S- and SO2-containing samples are usually preconcentrated via solid sorbents and are then detected by gas chromatographic techniques. However, such analytical strategies may be of limited selectivity, and the dimensions and operation modalities of the involved instruments prevent routine field usage. In this contribution, we therefore describe an innovative portable mid-infrared chemical sensor for simultaneously determining and quantifying gaseous H2S and SO2 via coupling a substrate-integrated hollow waveguides (iHWG) serving as a highly miniaturized mid-infrared photon conduit and gas cell with a custom-made preconcentration tube and an in-line UV-converter device. Both species were collected onto a solid sorbent within the preconcentrator and then released by thermal desorption into the UV-device. Hydrogen sulfide is detected by UV-assisted quantitative conversion of the rather weak IR-absorber H2S into SO2, which provides a significantly more pronounced and distinctively detectable rovibrational signature. Modulation of the UV-device system (i.e., UV-lamp on/off) enables discriminating between SO2 generated from H2S conversion and abundant SO2 signals. After optimization of the operational parameters, calibrations in the range of 0.75-10 ppmv with a limit of detection (LOD) at 77 ppbv for SO2 and 207 ppbv for H2S were established after 20 min of sampling time at 200 mL min(-1). Taking advantage of the device flexibility in terms of sampling time, flow-rate, and iHWG design facilitates tailoring the developed Preconcentrator-UV-device-iHWG device toward a wide variety of application scenarios ranging from environmental/atmospheric monitoring to industrial process monitoring and clinical diagnostics.

Sulfur Geochemical Analysis and Interpretation with ChemCam on the Curiosity Rover

NASA Astrophysics Data System (ADS)

Clegg, S. M.; Anderson, R. B.; Frydenvang, J.; Forni, O.; Newsom, H. E.; Blaney, D. L.; Maurice, S.; Wiens, R. C.

2017-12-01

The Curiosity rover has encountered many forms of sulfur including calcium sulfate veins [1], hydrated Mg sulfates, and Fe sulfates along the traverse through Gale crater. A new SO3 calibration model for the remote Laser-Induced Breakdown Spectroscopy (LIBS) technique used by the ChemCam instrument enables improved quantitative analysis of SO3, which has not been previously reported by ChemCam on a routine or quantitative basis. In this paper, the details of this new LIBS calibration model will be described and applied to many disparate Mars targets. Among them, Mavor contains a calcium sulfate vein surrounded by bedrock. In contrast, Jake M. is a float rock, Wernecke is a bedrock, Cumberland and Windjana are drill targets. In 2015 the ChemCam instrument team completed a re-calibration of major elements based on a significantly expanded set of >500 geochemical standards using the ChemCam testbed at Los Alamos National Laboratory [2]. In addition to these standards, the SO3 compositional range was recently extended with a series of doped samples containing various mixtures of Ca- and Mg-sulfate with basalt BHVO2. Spectra from these standards were processed per [4]. Calibration and Mars spectra were converted to peak-area-summed LIBS spectra that enables the SO3 calibration. These peak-area spectra were used to generate three overlapping partial least squares (PLS1) calibration sub-models as described by Anderson et al. [3, 5]. ChemCam analysis of Mavor involved a 3x3 raster in which locations 5 and 6 primarily probed Ca-sulfate material. The new ChemCam SO3 compositions for Mavor 5 and Mavor 6 are 48.6±1.2 and 50.3±1.2 wt% SO3, respectively. The LIBS spectra also recorded the presence of other elements that are likely responsible for the departure from pure Ca-sulfate chemistry. On the low-abundance side, the remaining 7 Mavor locations, Jake M., Cumberland, Windjana, and Wernecke all contain much lower SO3, between 1.4±0.5 wt% and 2.3±0.3 wt% SO3. [1] Nachon et al. J. Geophys. Res. Planets, doi:10.1002/2013JE004588. [2] Clegg et al. Spectrochimica Acta B, 2017, [3] Anderson et al. Spectrochimica Acta B, 2017. [4] Wiens et al. Spectrochimica Acta B, 2013, 82, 1-17, [5] Anderson et al. 3rd Planetary Data Workshop, abst. 7061, 2017.

Chemical profiling in Moutan Cortex after sulfuring and desulfuring processes reveals further insights into the quality control of TCMs by nontargeted metabolomic analysis.

PubMed

Zhan, Zhi-Lai; Deng, Ai-Ping; Kang, Li-Ping; Tang, Jin-Fu; Nan, Tie-Gui; Chen, Tong; He, Ya-Li; Guo, Lan-Ping; Huang, Lu-Qi

2018-05-01

As a traditional processing method, sulfuring has been used in the processing of many traditional Chinese medicines (TCMs). Desulfuring, which has emerged in recent years, is a new method applied to sulfured herbs so they can comply with regulations regarding residual SO 2 . Due to the chemical transformations and the residual SO 2 in the herbs, both sulfuring and desulfuring have negative effects on the safety and therapeutic effects of TCMs, and Moutan Cortex is one of the TCMs most susceptible to these effects. Here, a new strategy was developed to differentiate normal, sulfured and desulfured Moutan Cortex, and the transformations of compounds in sulfuring and desulfuring processes were analyzed using ultra-performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (UPLC/Q-TOF-MSE) method based on metabolomic analysis. Our findings were as follows: (1) a total of 119 compounds were identified or tentatively identified, including 9 compounds that are being reported for the first time as natural products; (2) 15 sulfocompounds were generated during the sulfuring process; (3) these sulfocompounds could not be converted back into their corresponding glycosides by the desulfuring process, and the desulfuring decreased the residual SO 2 ,while also removing some soluble compounds in the sulfured Moutan Cortex; and (4) 28 compounds were screened and tentatively identified as markers for distinguishing normal, sulfured and desulfured Moutan Cortex. Our findings provide a new practical strategy for evaluating how sulfuring and desulfuring affect the quality of TCMs. Copyright © 2018 Elsevier B.V. All rights reserved.

Experimental study and kinetic modeling of hydrogen and carbon monoxide oxidation perturbed by nitrogen and sulfur oxides

NASA Astrophysics Data System (ADS)

Mueller, Mark Anthony

2000-10-01

Increasingly stringent regulations have and will likely continue to place considerable constraints on combustion-generated pollutants, including carbon monoxide, nitrogen oxides, and sulfur oxides. The speciation of these pollutants and, by extension, their impact, is likely affected by kinetic interactions that occur during post-combustion processes. To gain a fundamental understanding of these interactions, the oxidation of hydrogen and carbon monoxide in the presence of trace quantities of NO, NO2, and SO2 was experimentally and numerically studied at conditions relevant to modern internal combustion engines. Experimental data were obtained using a well-characterized flow reactor over pressure and temperature ranges of 0.4--14.0 atm and 750--1040 K, respectively, using dilute (˜1% fuel) H2/O2 and CO/H2O/O2 mixtures perturbed with ppm quantities of NO, NO2, and/or SO2. The overall effects of these species were found to be highly sensitive to pressure, temperature, and equivalence ratio. In general, small quantities of NO promoted fuel consumption by converting HO2 radicals to highly reactive OH radicals, while high concentrations of NO and/or NO2 were inhibiting due to the catalysis of radical recombination reactions. In the absence of NO, SO2 strongly inhibited CO oxidation, but the simultaneous presence of NO and SO2 yielded synergistic effects that significantly reduced the inhibition from SO 2. Over the range of conditions explored, direct interactions between NOx and SOx species did rot appear to significantly influence the relative NO and NO2 concentrations; however, the reaction between NO2 and SO2 may be an important source of SO3 in certain circumstances. A detailed reaction mechanism. has been developed in a hierarchical manner, beginning with the H2/O2 and CO/H2O/O 2 systems and sequentially adding reactions necessary to describe the perturbing effects of NOx and SOx species. The experimental data were used in conjunction with gradient sensitivity and reaction flux analyses to determine key reaction pathways and to derive rate data for the H+O2(+M)=HO2(+M), H2+NO2=HONO+H, and SO2+O(+M) SO3(+M) reactions. Modifications to the rate constants for these and other reactions are discussed in relation to the mechanism's predictive ability with respect to the H2/O 2, CO/H2O/O2, H2/NO2, H 2/O2/NOx, and CO/H2O/O2/NO x/SOx systems over a wide range of conditions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shearer, J.; Callan, P; Amie, J

Nitrile hydratases (NHases) are non-heme Fe{sup III} or non-corrin Co{sup III} containing metalloenzymes that possess an N{sub 2}S{sub 3} ligand environment with nitrogen donors derived from amidates and sulfur donors derived from cysteinates. A closely related enzyme is thiocyanate hydrolase (SCNase), which possesses a nearly identical active-site coordination environment as CoNHase. These enzymes are redox inactive and perform hydrolytic reactions; SCNase hydrolyzes thiocyanate anions while NHase converts nitriles into amides. Herein an active CoNHase metallopeptide mimic, [Co{sup III}NHase-m1] (NHase-m1 = AcNH-CCDLP-CGVYD-PA-COOH), that contains Co{sup III} in a similar N{sub 2}S{sub 3} coordination environment as CoNHase is reported. [Co{sup III}NHase-m1] wasmore » characterized by electrospray ionization-mass spectrometry (ESI-MS), gel-permeation chromatography (GPC), Co K-edge X-ray absorption spectroscopy (Co-S: 2.21 {angstrom}; Co-N: 1.93 {angstrom}), vibrational, and optical spectroscopies. We find that [Co{sup III}NHase-m1] will perform the catalytic conversion of acrylonitrile into acrylamide with up to 58 turnovers observed after 18 h at 25 C (pH 8.0). FTIR data used in concert with calculated vibrational data (mPWPW91/aug-cc-TZVPP) demonstrates that the active form of [Co{sup III}NHase-m1] has a ligated SO{sub 2} (? = 1091 cm{sup -1}) moiety and a ligated protonated SO(H) (? = 928 cm{sup -1}) moiety; when only one oxygenated cysteinate ligand (i.e., a mono-SO{sub 2} coordination motif) or the bis-SO{sub 2} coordination motif are found within [Co{sup III}NHase-m1] no catalytic activity is observed. Calculations of the thermodynamics of ligand exchange (B3LYP/aug-cc-TZVPP) suggest that the reason for this is that the SO{sub 2}/SO(H) equatorial ligand motif promotes both water dissociation from the Co{sup III}-center and nitrile coordination to the Co{sup III}-center. In contrast, the under- or overoxidized motifs will either strongly favor a five coordinate Co{sup III}-center or strongly favor water binding to the Co{sup III}-center over nitrile binding.« less

Evolution of Automotive Chopper Circuits Towards Ultra High Efficiency and Power Density

NASA Astrophysics Data System (ADS)

Pavlovsky, Martin; Tsuruta, Yukinori; Kawamura, Atsuo

Automotive industry is considered to be one of the main contributors to environmental pollution and global warming. Therefore, many car manufacturers are in near future planning to introduce hybrid electric vehicles (HEV), fuel cell electric vehicles (FCEV) and pure electric vehicles (EV) to make our cars more environmentally friendly. These new vehicles require highly efficient and small power converters. In recent years, considerable improvements were made in designing such converters. In this paper, an approach based on so called Snubber Assisted Zero Voltage and Zero Current Switching topology otherwise also known as SAZZ is presented. This topology has evolved to be one of the leaders in the field of highly efficient converters with high power densities. Evolution and main features of this topology are briefly discussed. Capabilities of the topology are demonstrated on two case study prototypes based on different design approaches. The prototypes are designed to be fully bi-directional for peak power output of 30kW. Both designs reached efficiencies close to 99% in wide load range. Power densities over 40kW/litre are attainable in the same time. Combination of MOSFET technology and SAZZ topology is shown to be very beneficial to converters designed for EV applications.

[Screening and identification of a bacterium capable of converting agar to neoagaro oligosaccharides].

PubMed

Han, Junping; Huang, Yayan; Ye, Jing; Xiao, Meitian

2015-09-04

To screen and identify a bacterium capable of converting agar to neoagaro oligosaccharides. We took samples of porphyra haitanensis and nearby seawater, and then used the medium containing 1 per thousand agar to enrich the target bacteria. The target isolates were obtained by dilution-plate method, of which crude enzymes were further obtained by liquid culture. We adopted DNS method to determine the target bacteria which can convert agar to neoagaro oligosaccharides. The phylogenetics was identified by analyzing 16S rDNA sequence and combining the strain's morphological and bacterial colonial physiological biochemical characteristics. We isolated a gram-negative bacterial strain HJPHYXJ-1 capable of transforming agar to neoagaro oligosaccharides. Basic Local Alignment Search Tool (BLAST) search of HJPHYXJ-1's 16S rDNA sequence on GenBank suggested that the similarity between this strain and Vibrio natriegens reached 99% . In addition, the morphological and physiological biochemical characteristics of HJPHYXJ-1 also showed highly similarity to Vibrio natriegens. So we identified HJPHYXJ-1 as Vibrio natriegens. The results of HPLC suggested that the metabolite of enzymatic degradation was neoagaro oligosaccharides. HJPHYXJ-1 or the new isolate of Vibrio natriegens was capable of converting agar to neoagaro oligosaccharides.

Evolution in boron-based GEM detectors for diffraction measurements: from planar to 3D converters

NASA Astrophysics Data System (ADS)

Albani, Giorgia; Perelli Cippo, Enrico; Croci, Gabriele; Muraro, Andrea; Schooneveld, Erik; Scherillo, Antonella; Hall-Wilton, Richard; Kanaki, Kalliopi; Höglund, Carina; Hultman, Lars; Birch, Jens; Claps, Gerardo; Murtas, Fabrizio; Rebai, Marica; Tardocchi, Marco; Gorini, Giuseppe

2016-11-01

The so-called ‘3He-crisis’ has motivated the neutron detector community to undertake an intense R&D programme in order to develop technologies alternative to standard 3He tubes and suitable for neutron detection systems in future spallation sources such as the European spallation source (ESS). Boron-based GEM (gas electron multiplier) detectors are a promising ‘3He-free’ technology for thermal neutron detection in neutron scattering experiments. In this paper the evolution of boron-based GEM detectors from planar to 3D converters with an application in diffraction measurements is presented. The use of 3D converters coupled with GEMs allows for an optimization of the detector performances. Three different detectors were used for diffraction measurements on the INES instrument at the ISIS spallation source. The performances of the GEM-detectors are compared with those of conventional 3He tubes installed on the INES instrument. The conceptual detector with the 3D converter used in this paper reached a count rate per unit area of about 25% relative to the currently installed 3He tube. Its timing resolution is similar and the signal-to-background ratio (S/B) is 2 times lower.

Determination of the delta(15N/14N)of Ammonium (NH4+) in Water: RSIL Lab Code 2898

USGS Publications Warehouse

Hannon, Janet E.; Böhlke, John Karl

2008-01-01

The purpose of the technique described by Reston Stable Isotope Laboratory (RSIL) lab code 2898 is to determine the N isotopic composition, delta(15N/14N), abbreviated as d15N, of ammonium (NH4+) in water (freshwater and saline water). The procedure involves converting dissolved NH4+ into NH3 gas by raising the pH of the sample to above 9 with MgO and subsequently trapping the gas quantitatively as (NH4)2SO4 on a glass fiber (GF) filter. The GF filter is saturated with NaHSO4 and pressure sealed between two gas-permeable polypropylene filters. The GF filter 'sandwich' floats on the surface of the water sample in a closed bottle. NH3 diffuses from the water through the polypropylene filter and reacts with NaHSO4, forming (NH4)2SO4 on the GF filter. The GF filter containing (NH4)2SO4 is dried and then combusted with a Carlo Erba NC 2500 elemental analyzer (EA), which is used to convert total nitrogen in a solid sample into N2 gas. The EA is connected to a continuous-flow isotope-ratio mass spectrometer (CF-IRMS), which determines the relative difference in ratios of the amounts of the stable isotopes of nitrogen (15N and 14N) of the product N2 gas and a reference N2 gas. The filters containing the samples are compressed in tin capsules and loaded into a Costech Zero-Blank Autosampler on the EA. Under computer control, samples then are dropped into a heated reaction tube that contains an oxidant, where combustion takes place in a He atmosphere containing an excess of O2 gas. To remove S-O gases produced from the NaHSO4, a plug of Ag-coated Cu wool is inserted at the bottom of the reaction tube. Combustion products are transported by a He carrier through a reduction furnace to remove excess O2, toconvert all nitrogen oxides to N2, and to remove any remaining S-O gases. The gases then pass through a drying tube to remove water. The gas-phase products, mainly N2 and a small amount of background CO2, are separated by a gas chromatograph (GC). The gas is then introduced into the IRMS through a Finnigan ConFlo II interface. The ConFlo II interface is used to introduce not only sample into the IRMS but also N2 reference gas and He for sample dilution. The flash combustion is quantitative, so no isotopic fractionation is involved. The IRMS is a Finnigan Delta V CF-IRMS with 10 cups and is capable of detecting ion beams with mass/charge (m/z) 28, 29, 30. The ion beams from N2 are as follows: m/z 28 = 14N14N, m/z 29 = 14N15N, and m/z 30 = 15N15N. The ion beam with m/z 30 also represents 14N16O, which may indicate contamination or incomplete reduction.

Politics and population health: Testing the impact of electoral democracy.

PubMed

Patterson, Andrew C; Veenstra, Gerry

2016-07-01

This study addresses questions of whether and why electoral democracies have better health than other nations. After devising a replicable approach to missing data, we compare political, economic, and health-related data for 168 nations collected annually from 1960 through 2010. Regression models estimate that electoral democracies have 11 years of longer life expectancy on average and 62.5% lower rates of infant mortality. The association with life expectancy reduces markedly after controlling for GDP, while a combination of factors may explain the democratic advantage in infant health. Results suggest that income inequality associates independently with both health outcomes but does not mediate their associations with democracy. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mathematics of the Bulgarian Electoral System

NASA Astrophysics Data System (ADS)

Konstantinov, Mihail M.; Pelova, Galina B.; Boneva, Juliana K.

2009-11-01

In this paper we consider the mathematical aspects of the Bulgarian proportional electoral systems used since 1990. They are variants of a proportional system at a nationwide level with 4-percent barrier such that the party seats are personified from a number of regional party lists. This system is unique in the world electoral practice and may lead to severe inter-party distortions. These distortions although formally correct are hardly accepted by the public and by local party activists in particular. Methods to overcome these difficulties as well as the status-quo of the problem are considered. Finally new paradoxes are studied which are generalizations of the well known paradoxes for the plain proportional systems.

Improved Satellite Retrievals of NO2 and SO2 over the Canadian Oil Sands and Comparisons with Surface Measurements

NASA Technical Reports Server (NTRS)

McLinden, C. A.; Fioletov, V.; Boersma, K. F.; Kharol, S. K.; Krotkov, N.; Lamsal, L.; Makar, P. A.; Martin, R. V.; Veefkind, J. P.; Yang, K.

2014-01-01

Satellite remote sensing is increasingly being used to monitor air quality over localized sources such as the Canadian oil sands. Following an initial study, significantly low biases have been identified in current NO2 and SO2 retrieval products from the Ozone Monitoring Instrument (OMI) satellite sensor over this location resulting from a combination of its rapid development and small spatial scale. Air mass factors (AMFs) used to convert line-of-sight "slant" columns to vertical columns were re-calculated for this region based on updated and higher resolution input information including absorber profiles from a regional-scale (15 km × 15 km resolution) air quality model, higher spatial and temporal resolution surface reflectivity, and an improved treatment of snow. The overall impact of these new Environment Canada (EC) AMFs led to substantial increases in the peak NO2 and SO2 average vertical column density (VCD), occurring over an area of intensive surface mining, by factors of 2 and 1.4, respectively, relative to estimates made with previous AMFs. Comparisons are made with long-term averages of NO2 and SO2 (2005-2011) from in situ surface monitors by using the air quality model to map the OMI VCDs to surface concentrations. This new OMI-EC product is able to capture the spatial distribution of the in situ instruments (slopes of 0.65 to 1.0, correlation coefficients of greater than 0.9). The concentration absolute values from surface network observations were in reasonable agreement, with OMI-EC NO2 and SO2 biased low by roughly 30%. Several complications were addressed including correction for the interference effect in the surface NO2 instruments and smoothing and clear-sky biases in the OMI measurements. Overall these results highlight the importance of using input information that accounts for the spatial and temporal variability of the location of interest when performing retrievals.

Angiotensin II receptor one (AT1) mediates dextrose induced endoplasmic reticulum stress and superoxide production in human coronary artery endothelial cells.

PubMed

Haas, Michael J; Onstead-Haas, Luisa; Lee, Tracey; Torfah, Maisoon; Mooradian, Arshag D

2016-10-01

Renin-angiotensin-aldosterone system (RAAS) has been implicated in diabetes-related vascular complications partly through oxidative stress. To determine the role of angiotensin II receptor subtype one (AT1) in dextrose induced endoplasmic reticulum (ER) stress, another cellular stress implicated in vascular disease. Human coronary artery endothelial cells with or without AT1 receptor knock down were treated with 27.5mM dextrose for 24h in the presence of various pharmacologic blockers of RAAS and ER stress and superoxide (SO) production were measured. Transfection of cells with AT1 antisense RNA knocked down cellular AT1 by approximately 80%. The ER stress was measured using the placental alkaline phosphatase (ES-TRAP) assay and western blot analysis of glucose regulated protein 78 (GRP78), c-jun-N-terminal kinase 1 (JNK1), phospho-JNK1, eukaryotic translation initiation factor 2α (eIF2α) and phospho-eIF2α measurements. Superoxide (SO) generation was measured using the superoxide-reactive probe 2-methyl-6-(4-methoxyphenyl)-3,7-dihydroimidazo[1,2-A]pyrazin-3-one hydrochloride (MCLA) chemiluminescence. In cells with AT1 knock down, dextrose induced ER stress was significantly blunted and treatment with 27.5mM dextrose resulted in significantly smaller increase in SO production compared to 27.5mM dextrose treated and sham transfected cells. Dextrose induced ER stress was reduced with pharmacologic blockers of AT1 (losartan and candesartan) and mineralocorticoid receptor blocker (spironolactone) but not with angiotensin converting enzyme inhibitors (captopril and lisinopril). The dextrose induced SO generation was inhibited by all pharmacologic blockers of RAAS tested. The results indicate that dextrose induced ER stress and SO production in endothelial cells are mediated at least partly through AT1 receptor activation. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Radio-over-optical waveguide system-on-wafer for massive delivery capacity 5G MIMO access networks

NASA Astrophysics Data System (ADS)

Binh, Le N.

2017-01-01

Delivering maximum information capacity over MIMO antennae systems beam steering is critical so as to achieve the flexibility via beam steering, maximizing the number of users or community of users in Gb/s rate per user over distributed cloud-based optical-wireless access networks. This paper gives an overview of (i) demands of optical - wireless delivery with high flexibility, especially the beam steering of multi-Tbps information channels to information hungry community of users via virtualized beam steering MIMO antenna systems at the free-license mmW region; (ii) Proposing a novel photonic planar integrated waveguide systems composing several passive and active, passive and amplification photonic devices so as to generate mmW carrier and embedded baseband information channels to feed to antenna elements; (iii) Integration techniques to generate a radio over optical waveguide (RoOW) system-on-wafer (SoW) comprising MIMO planar antenna elements and associate photonic integrated circuits for both up- and down- links; (iv) Challenges encountered in the implementation of the SoW in both wireless and photonic domains; (v) Photonic modulation techniques to achieve maximum transmission capacity per wavelength per MIMO antenna system. (vi) A view on control-feedback systems for fast and accurate generation of phase pattern for MIMO beam steering via a bank of optical phase modulators to mmW carrier phases and their preservation in the converted mmW domain . (vi) The overall operational principles of the novel techniques and technologies based on the coherent mixing of two lightwave channels The entire SoW can be implemented on SOI Si-photonic technology or via hybrid integration. These technological developments and their pros- and cons- will be discussed to achieve 50Tera-bps over the extended 110 channel Cband single mode fiber with mmW centered at 58.6GHz and 7GHz free-license band.

Spaghetti Politics: Local Electoral Systems and Alliance Structure in Italy, 1984-2001

ERIC Educational Resources Information Center

Parigi, Paolo; Bearman, Peter S.

2008-01-01

This article describes the impact of the Italian electoral reforms of 1993 on the structure of local political alliances. The reform, which moved Italy from a purely proportional representation system to a mixed, largely majoritarian system, was designed to increase transparency, reduce corruption, limit the number of political parties, and create…

The Impact of Redistricting on Latino Education Policy: A Texas Case Study

ERIC Educational Resources Information Center

Chapa, Jorge; Garcia, Emmanuel

2013-01-01

Redistricting, the redrawing of electoral district boundaries to reflect the latest population counts, occurs for most electoral districts after each decennial census. While normally a topic of concern mainly to politicians and politicos, redistricting can alter the opportunities for representation and policy alternatives. For a number of reasons,…

Vote. Speak Out. 3-6.

ERIC Educational Resources Information Center

Illinois State Board of Education, Springfield.

The purpose of this election-education program is to help develop an informed electorate and to instill in future voters an appreciation of the importance of the right to vote. It provides a framework for discussions of the electoral process and gives students in grades three through six an opportunity to face the responsibilities and challenges…

Analysis of Spatial Voting Patterns: An Approach in Political Socialization

ERIC Educational Resources Information Center

Klimasewski, Ted

1973-01-01

Passage of the 26th Amendment gave young adults the right to vote. This study attempts to further student understanding of the electoral process by presenting a method for analyzing spatial voting patterns. The spatial emphasis adds another dimension to the temporal and behavioral-structural approaches in studying the American electoral system.…

Purple States in the 2016 Presidential Election

ERIC Educational Resources Information Center

Shelley, Fred M.; Hitt, Ashley M.

2016-01-01

Given the nature of the Electoral College system, the two major political parties concentrate on winning the electoral votes of those states in which the preference of voters are divided evenly. Thus, the parties and their candidates ignore states such as Wyoming and Oklahoma, which are reliably Republican, and they ignore states such as…

Methode unifiee de simulation et de conception des convertisseurs de puissance

NASA Astrophysics Data System (ADS)

Fortin Blanchette, Handy

High frequency power converters are now master piece in emerging new renewable energy applications such as hybrid vehicules. These new technologies merge the power of electrical machine with the thermal motor power. The power converters used to control those electrical machines are embeded technologies with high efficiency conversion and a high reliability. More than ground vehicule applications, embeded power converters are now present in aeronautic and aerospace domains. In this sense, high reliability and high efficiency are now important characteristics that are not only suitable but needed. In spite of this progression, power converters development remains today a complex science. Even if advanced complex techniques are now available to increase the converter stability, there are no systemic rules to design the converter physical assembly. Very often, an artistic approach is used to place the components inside the converter in the more convenient places. This lack of rigor about EMI problems is not so surprising because this kind of analysis is costly and risky. In general, to solve this type of problems, one designs a second and a third printed circuit generation which is not necessarily a quick and systematic approach. To overcome these difficulties, the main goal of this thesis is to provide simple and improved tools for power converter circuit designers. The key point are to solve EMI and reliability problems at the earlier design stage and not during the prototyping phase. Many solutions are exposed in this text about the magnetic field orientation, leakage inductances identification, power semiconductors modeling and electromagnetic modeling of power converters. The exactness of these methods is proved by using it to develop a matrix converter. The printed circuits are designed to orient properly the magnetic field enabling to introduce low power sensing circuits directly inside the converter. This application is one of the numerous possibilities offered by the techniques presented in this document. Keywords: power converters, modeling, electromagnetic interferences.

A 3.9 ps Time-Interval RMS Precision Time-to-Digital Converter Using a Dual-Sampling Method in an UltraScale FPGA

NASA Astrophysics Data System (ADS)

Wang, Yonggang; Liu, Chong

2016-10-01

Field programmable gate arrays (FPGAs) manufactured with more advanced processing technology have faster carry chains and smaller delay elements, which are favorable for the design of tapped delay line (TDL)-style time-to-digital converters (TDCs) in FPGA. However, new challenges are posed in using them to implement TDCs with a high time precision. In this paper, we propose a bin realignment method and a dual-sampling method for TDC implementation in a Xilinx UltraScale FPGA. The former realigns the disordered time delay taps so that the TDC precision can approach the limit of its delay granularity, while the latter doubles the number of taps in the delay line so that the TDC precision beyond the cell delay limitation can be expected. Two TDC channels were implemented in a Kintex UltraScale FPGA, and the effectiveness of the new methods was evaluated. For fixed time intervals in the range from 0 to 440 ns, the average RMS precision measured by the two TDC channels reaches 5.8 ps using the bin realignment, and it further improves to 3.9 ps by using the dual-sampling method. The time precision has a 5.6% variation in the measured temperature range. Every part of the TDC, including dual-sampling, encoding, and on-line calibration, could run at a 500 MHz clock frequency. The system measurement dead time is only 4 ns.

Push-pull converter with energy saving circuit for protecting switching transistors from peak power stress

NASA Technical Reports Server (NTRS)

Mclyman, W. T. (Inventor)

1981-01-01

In a push-pull converter, switching transistors are protected from peak power stresses by a separate snubber circuit in parallel with each comprising a capacitor and an inductor in series, and a diode in parallel with the inductor. The diode is connected to conduct current of the same polarity as the base-emitter juction of the transistor so that energy stored in the capacitor while the transistor is switched off, to protect it against peak power stress, discharges through the inductor when the transistor is turned on, and after the capacitor is discharges through the diode. To return this energy to the power supply, or to utilize this energy in some external circuit, the inductor may be replaced by a transformer having its secondary winding connected to the power supply or to the external circuit.

Artificial Neural Identification and LMI Transformation for Model Reduction-Based Control of the Buck Switch-Mode Regulator

NASA Astrophysics Data System (ADS)

Al-Rabadi, Anas N.

2009-10-01

This research introduces a new method of intelligent control for the control of the Buck converter using newly developed small signal model of the pulse width modulation (PWM) switch. The new method uses supervised neural network to estimate certain parameters of the transformed system matrix [Ã]. Then, a numerical algorithm used in robust control called linear matrix inequality (LMI) optimization technique is used to determine the permutation matrix [P] so that a complete system transformation {[B˜], [C˜], [Ẽ]} is possible. The transformed model is then reduced using the method of singular perturbation, and state feedback control is applied to enhance system performance. The experimental results show that the new control methodology simplifies the model in the Buck converter and thus uses a simpler controller that produces the desired system response for performance enhancement.

High voltage systems (tube-type microwave)/low voltage system (solid-state microwave) power distribution

NASA Technical Reports Server (NTRS)

Nussberger, A. A.; Woodcock, G. R.

1980-01-01

SPS satellite power distribution systems are described. The reference Satellite Power System (SPS) concept utilizes high-voltage klystrons to convert the onboard satellite power from dc to RF for transmission to the ground receiving station. The solar array generates this required high voltage and the power is delivered to the klystrons through a power distribution subsystem. An array switching of solar cell submodules is used to maintain bus voltage regulation. Individual klystron dc voltage conversion is performed by centralized converters. The on-board data processing system performs the necessary switching of submodules to maintain voltage regulation. Electrical power output from the solar panels is fed via switch gears into feeder buses and then into main distribution buses to the antenna. Power also is distributed to batteries so that critical functions can be provided through solar eclipses.

Research on design feasibility of high-power light-weight dc-to-dc converters for space power applications

NASA Technical Reports Server (NTRS)

Wilson, T. G.

1981-01-01

Utilizing knowledge gained from past experience with experimental current-or-voltage step-up dc-to-dc converter power stages operating at output powers up to and in excess of 2 kW, a new experimental current-or-voltage step-up power stage using paralleled bipolar junction transistors (BJTs) as the controlled power switch, was constructed during the current reporting period. The major motivation behind the construction of this new experimental power stage was to improve the circuit layout so as to reduce the effects of stray circuit parasitic inductances resulting from excess circuit lead lengths and circuit loops, and to take advantage of the layout improvements which could be made when some recently-available power components, particularly power diodes and polypropylene filter capacitors, were incorporated into the design.

Digital readout for image converter cameras

NASA Astrophysics Data System (ADS)

Honour, Joseph

1991-04-01

There is an increasing need for fast and reliable analysis of recorded sequences from image converter cameras so that experimental information can be readily evaluated without recourse to more time consuming photographic procedures. A digital readout system has been developed using a randomly triggerable high resolution CCD camera, the output of which is suitable for use with IBM AT compatible PC. Within half a second from receipt of trigger pulse, the frame reformatter displays the image and transfer to storage media can be readily achieved via the PC and dedicated software. Two software programmes offer different levels of image manipulation which includes enhancement routines and parameter calculations with accuracy down to pixel levels. Hard copy prints can be acquired using a specially adapted Polaroid printer, outputs for laser and video printer extend the overall versatility of the system.

The 235U Prompt Fission Neutron Spectrum in the BR1 Reactor at SCK•CEN

NASA Astrophysics Data System (ADS)

Wagemans, Jan; Malambu, Edouard; Borms, Luc; Fiorito, Luca

2016-02-01

The BR1 research reactor at SCK•CEN has a spherical cavity in the graphite above the reactor core. In this cavity an accurately characterised Maxwellian thermal neutron field is present. Different converters can be loaded in the cavity in order to obtain other types of neutron (and gamma) irradiation fields. Inside the so-called MARK III converter a fast 235U(n,f) prompt fission neutron field can be obtained. With the support of MCNP calculations, irradiations in MARK III can be directly related to the pure 235U(n,f) prompt fission neutron spectrum. For this purpose MARK III spectrum averaged cross sections for the most relevant fluence dosimetry reactions have been determined. A calibration factor for absolute measurements has been determined applying activation dosimetry following ISO/IEC 17025 standards.

Design of an Intelligent Front-End Signal Conditioning Circuit for IR Sensors

NASA Astrophysics Data System (ADS)

de Arcas, G.; Ruiz, M.; Lopez, J. M.; Gutierrez, R.; Villamayor, V.; Gomez, L.; Montojo, Mª. T.

2008-02-01

This paper presents the design of an intelligent front-end signal conditioning system for IR sensors. The system has been developed as an interface between a PbSe IR sensor matrix and a TMS320C67x digital signal processor. The system architecture ensures its scalability so it can be used for sensors with different matrix sizes. It includes an integrator based signal conditioning circuit, a data acquisition converter block, and a FPGA based advanced control block that permits including high level image preprocessing routines such as faulty pixel detection and sensor calibration in the signal conditioning front-end. During the design phase virtual instrumentation technologies proved to be a very valuable tool for prototyping when choosing the best A/D converter type for the application. Development time was significantly reduced due to the use of this technology.

Recycling rice husks for high-capacity lithium battery anodes

PubMed Central

Jung, Dae Soo; Ryou, Myung-Hyun; Sung, Yong Joo; Park, Seung Bin; Choi, Jang Wook

2013-01-01

The rice husk is the outer covering of a rice kernel and protects the inner ingredients from external attack by insects and bacteria. To perform this function while ventilating air and moisture, rice plants have developed unique nanoporous silica layers in their husks through years of natural evolution. Despite the massive amount of annual production near 108 tons worldwide, so far rice husks have been recycled only for low-value agricultural items. In an effort to recycle rice husks for high-value applications, we convert the silica to silicon and use it for high-capacity lithium battery anodes. Taking advantage of the interconnected nanoporous structure naturally existing in rice husks, the converted silicon exhibits excellent electrochemical performance as a lithium battery anode, suggesting that rice husks can be a massive resource for use in high-capacity lithium battery negative electrodes. PMID:23836636

Recycling rice husks for high-capacity lithium battery anodes.

PubMed

Jung, Dae Soo; Ryou, Myung-Hyun; Sung, Yong Joo; Park, Seung Bin; Choi, Jang Wook

2013-07-23

The rice husk is the outer covering of a rice kernel and protects the inner ingredients from external attack by insects and bacteria. To perform this function while ventilating air and moisture, rice plants have developed unique nanoporous silica layers in their husks through years of natural evolution. Despite the massive amount of annual production near 10(8) tons worldwide, so far rice husks have been recycled only for low-value agricultural items. In an effort to recycle rice husks for high-value applications, we convert the silica to silicon and use it for high-capacity lithium battery anodes. Taking advantage of the interconnected nanoporous structure naturally existing in rice husks, the converted silicon exhibits excellent electrochemical performance as a lithium battery anode, suggesting that rice husks can be a massive resource for use in high-capacity lithium battery negative electrodes.

Explosive plane-wave lens

DOEpatents

Marsh, Stanley P.

1988-01-01

An explosive plane-wave air lens which enables a spherical wave form to be converted to a planar wave without the need to specially machine or shape explosive materials is described. A disc-shaped impactor having a greater thickness at its center than around its periphery is used to convert the spherical wave into a plane wave. When the wave reaches the impactor, the center of the impactor moves first because the spherical wave reaches the center of the impactor first. The wave strikes the impactor later in time as one moves radially along the impactor. Because the impactor is thinner as one moves radially outward, the velocity of the impactor is greater at the periphery than at the center. An acceptor explosive is positioned so that the impactor strikes the acceptor simultaneously. Consequently, a plane detonation wave is propagated through the acceptor explosive.

Explosive plane-wave lens

DOEpatents

Marsh, S.P.

1988-03-08

An explosive plane-wave air lens which enables a spherical wave form to be converted to a planar wave without the need to specially machine or shape explosive materials is described. A disc-shaped impactor having a greater thickness at its center than around its periphery is used to convert the spherical wave into a plane wave. When the wave reaches the impactor, the center of the impactor moves first because the spherical wave reaches the center of the impactor first. The wave strikes the impactor later in time as one moves radially along the impactor. Because the impactor is thinner as one moves radially outward, the velocity of the impactor is greater at the periphery than at the center. An acceptor explosive is positioned so that the impactor strikes the acceptor simultaneously. Consequently, a plane detonation wave is propagated through the acceptor explosive. 4 figs.

Milestones on the road to independence for the blind

NASA Astrophysics Data System (ADS)

Reed, Kenneth

1997-02-01

Ken will talk about his experiences as an end user of technology. Even moderate technological progress in the field of pattern recognition and artificial intelligence can be, often surprisingly, of great help to the blind. An example is the providing of portable bar code scanners so that a blind person knows what he is buying and what color it is. In this age of microprocessors controlling everything, how can a blind person find out what his VCR is doing? Is there some technique that will allow a blind musician to convert print music into midi files to drive a synthesizer? Can computer vision help the blind cross a road including predictions of where oncoming traffic will be located? Can computer vision technology provide spoken description of scenes so a blind person can figure out where doors and entrances are located, and what the signage on the building says? He asks 'can computer vision help me flip a pancake?' His challenge to those in the computer vision field is 'where can we go from here?'

Integrated photoelectrochemical energy storage: solar hydrogen generation and supercapacitor

PubMed Central

Xia, Xinhui; Luo, Jingshan; Zeng, Zhiyuan; Guan, Cao; Zhang, Yongqi; Tu, Jiangping; Zhang, Hua; Fan, Hong Jin

2012-01-01

Current solar energy harvest and storage are so far realized by independent technologies (such as solar cell and batteries), by which only a fraction of solar energy is utilized. It is highly desirable to improve the utilization efficiency of solar energy. Here, we construct an integrated photoelectrochemical device with simultaneous supercapacitor and hydrogen evolution functions based on TiO2/transition metal hydroxides/oxides core/shell nanorod arrays. The feasibility of solar-driven pseudocapacitance is clearly demonstrated, and the charge/discharge is indicated by reversible color changes (photochromism). In such an integrated device, the photogenerated electrons are utilized for H2 generation and holes for pseudocapacitive charging, so that both the reductive and oxidative energies are captured and converted. Specific capacitances of 482 F g−1 at 0.5 A g−1 and 287 F g−1 at 1 A g−1 are obtained with TiO2/Ni(OH)2 nanorod arrays. This study provides a new research strategy for integrated pseudocapacitor and solar energy application. PMID:23248745

An intercomparison of airborne nitrogen dioxide instruments

NASA Technical Reports Server (NTRS)

Gregory, G. L.; Hoell, J. M., Jr.; Carroll, M. A.; Ridley, B. A.; Davis, D. D.; Bradshaw, J.; Rodgers, M. O.; Sandholm, S. T.; Schiff, H. I.; Torres, A. L.

1990-01-01

Results on NO2 instruments are reported from the NASA Global Tropospheric Experiment Chemical Instrumentation Test and Evaluation 2 (CITE 2) program in summer 1986. The instruments tested were (1) a two-photon LIF system using a laser for NO2-NO photolysis, (2) a chemiluminescence (CL) detector using FeSO4 for NO2-NO conversion, (3) a CL detector using an arc lamp for NO2-NO photolysis, and (4) a tunable-laser-diode multipath-absorption system. The procedures for the CITE 2 ground-based and flight tests are described in detail, and the results are presented in extensive graphs. Instrument (2) was eliminated because the FeSO4 converted atmospheric PAN to NO, resulting in spuriously high NO2 values. The remaining instruments gave readings in 30-40-percent agreement at NO2 mixing ratios of 100-200 parts per trillion by volume (pptv). At ratios below 50 pptv, the correlation among the measurements was very poor, with a tendency for system (4) to give higher values than (1) or (3).

Hydroxynonenal and uncoupling proteins: a model for protection against oxidative damage.

PubMed

Echtay, Karim S; Pakay, Julian L; Esteves, Telma C; Brand, Martin D

2005-01-01

In this mini review we summarize recent studies from our laboratory that show the involvement of superoxide and the lipid peroxidation product 4-hydroxynonenal in the regulation of mitochondrial uncoupling. Superoxide produced during mitochondrial respiration is a major cause of the cellular oxidative damage that may underlie degenerative diseases and ageing. Superoxide production is very sensitive to the magnitude of the mitochondrial protonmotive force, so can be strongly decreased by mild uncoupling. Superoxide is able to give rise to other reactive oxygen species, which elicit deleterious effects primarily by oxidizing intracellular components, including lipids, DNA and proteins. Superoxide-induced lipid peroxidation leads to the production of reactive aldehydes, including 4-hydroxynonenal. These aldehydic lipid peroxidation products are in turn able to modify proteins such as mitochondrial uncoupling proteins and the adenine nucleotide translocase, converting them into active proton transporters. This activation induces mild uncoupling and so diminishes mitochondrial superoxide production, hence protecting against disease and oxidative damage at the expense of energy production.

Integrated photoelectrochemical energy storage: solar hydrogen generation and supercapacitor.

PubMed

Xia, Xinhui; Luo, Jingshan; Zeng, Zhiyuan; Guan, Cao; Zhang, Yongqi; Tu, Jiangping; Zhang, Hua; Fan, Hong Jin

2012-01-01

Current solar energy harvest and storage are so far realized by independent technologies (such as solar cell and batteries), by which only a fraction of solar energy is utilized. It is highly desirable to improve the utilization efficiency of solar energy. Here, we construct an integrated photoelectrochemical device with simultaneous supercapacitor and hydrogen evolution functions based on TiO(2)/transition metal hydroxides/oxides core/shell nanorod arrays. The feasibility of solar-driven pseudocapacitance is clearly demonstrated, and the charge/discharge is indicated by reversible color changes (photochromism). In such an integrated device, the photogenerated electrons are utilized for H(2) generation and holes for pseudocapacitive charging, so that both the reductive and oxidative energies are captured and converted. Specific capacitances of 482 F g(-1) at 0.5 A g(-1) and 287 F g(-1) at 1 A g(-1) are obtained with TiO(2)/Ni(OH)(2) nanorod arrays. This study provides a new research strategy for integrated pseudocapacitor and solar energy application.

Theoretical Calculation of the Gas-Sensing Properties of Pt-Decorated Carbon Nanotubes

PubMed Central

Zhang, Xiaoxing; Dai, Ziqiang; Wei, Li; Liang, Naifeng; Wu, Xiaoqing

2013-01-01

The gas-sensing properties of Pt-decorated carbon nanotubes (CNTs), which provide a foundation for the fabrication of sensors, have been evaluated. In this study, we calculated the gas adsorption of Pt-decorated (8,0) single-wall CNTs (Pt-SWCNTs) with SO2, H2S, and CO using GGA/PW91 method based on density functional theory. The adsorption energies and the changes in geometric and electronic structures after absorption were comprehensively analyzed to estimate the responses of Pt-SWCNTs. Results indicated that Pt-SWCNTs can respond to the three gases. The electrical characteristics of Pt-SWCNTs show different changes after adsorption. Pt-SWCNTs donate electrons and increase the number of hole carriers after adsorbing SO2, thereby enhancing its conductivity. When H2S is adsorbed on CNTs, electrons are transferred from H2S to Pt-SWCNTs, converting Pt-SWCNTs from p-type to n-type sensors with improved conductivity. However, Pt-SWCNTs obtain electrons and show decreased conductivity when reacted with CO gas. PMID:24201317

Comparison of forest edge effects on throughfall deposition in different forest types.

PubMed

Wuyts, Karen; De Schrijver, An; Staelens, Jeroen; Gielis, Leen; Vandenbruwane, Jeroen; Verheyen, Kris

2008-12-01

This study examined the influence of distance to the forest edge, forest type, and time on Cl-, SO4(2-), NO3(-), and NH4+ throughfall deposition in forest edges. The forests were dominated by pedunculate oak, silver birch, or Corsican/Austrian pine, and were situated in two regions of Flanders (Belgium). Along transects, throughfall deposition was monitored at distances of 0-128 m from the forest edge. A repeated-measures analysis demonstrated that time, forest type, and distance to the forest edge significantly influenced throughfall deposition of the ions studied. The effect of distance to the forest edge depended significantly on forest type in the deposition of Cl-, SO4(2-), and NO3(-): the edge effect was significantly greater in pine stands than in deciduous birch and oak stands. This finding supports the possibility of converting pine plantations into oak or birch forests in order to mitigate the input of nitrogen and potentially acidifying deposition.

Process and technoeconomic analysis of leading pretreatment technologies for lignocellulosic ethanol production using switchgrass.

PubMed

Tao, Ling; Aden, Andy; Elander, Richard T; Pallapolu, Venkata Ramesh; Lee, Y Y; Garlock, Rebecca J; Balan, Venkatesh; Dale, Bruce E; Kim, Youngmi; Mosier, Nathan S; Ladisch, Michael R; Falls, Matthew; Holtzapple, Mark T; Sierra, Rocio; Shi, Jian; Ebrik, Mirvat A; Redmond, Tim; Yang, Bin; Wyman, Charles E; Hames, Bonnie; Thomas, Steve; Warner, Ryan E

2011-12-01

Six biomass pretreatment processes to convert switchgrass to fermentable sugars and ultimately to cellulosic ethanol are compared on a consistent basis in this technoeconomic analysis. The six pretreatment processes are ammonia fiber expansion (AFEX), dilute acid (DA), lime, liquid hot water (LHW), soaking in aqueous ammonia (SAA), and sulfur dioxide-impregnated steam explosion (SO(2)). Each pretreatment process is modeled in the framework of an existing biochemical design model so that systematic variations of process-related changes are consistently captured. The pretreatment area process design and simulation are based on the research data generated within the Biomass Refining Consortium for Applied Fundamentals and Innovation (CAFI) 3 project. Overall ethanol production, total capital investment, and minimum ethanol selling price (MESP) are reported along with selected sensitivity analysis. The results show limited differentiation between the projected economic performances of the pretreatment options, except for processes that exhibit significantly lower monomer sugar and resulting ethanol yields. Copyright © 2011 Elsevier Ltd. All rights reserved.

Reductive atmospheric acid leaching of spent alkaline batteries in H2SO4/Na2SO3 solutions

NASA Astrophysics Data System (ADS)

Morcali, Mehmet Hakan

2015-07-01

This work studies the optimum reductive leaching process for manganese and zinc recovery from spent alkaline battery paste. The effects of reducing agents, acid concentration, pulp density, reaction temperature, and leaching time on the dissolution of manganese and zinc were investigated in detail. Manganese dissolution by reductive acidic media is an intermediate-controlled process with an activation energy of 12.28 kJ·mol-1. After being leached, manganese and zinc were selectively precipitated with sodium hydroxide. The zinc was entirely converted into zincate (Zn(OH){4/2-}) ions and thus did not co-precipitate with manganese hydroxide during this treatment (2.0 M NaOH, 90 min, 200 r/min, pH > 13). After the manganese was removed from the solution, the Zn(OH){4/2-} was precipitated as zinc sulfate in the presence of sulfuric acid. The results indicated that this process could be effective in recovering manganese and zinc from alkaline batteries.

Chemically activated manganese dioxide for dry batteries

NASA Astrophysics Data System (ADS)

Askar, M.; Abbas, H.

1994-10-01

The present investigation has enabled us to convert inactive beta-manganese dioxide to high electrochemically active types by chemical processes. Natural and chemically prepared beta-manganese dioxides were roasted at 1050 C to form Mn3O4. This compound was subjected to activation treatment using hydrochloric and sulfuric acid under various reaction conditions. The manganese dioxide so obtained was examined by x-ray diffraction, thermogravimetric, differential thermal, and chemical analyses. The structure of the dioxide obtained was found to be greatly dependent on the origin of MnO2 and type of acid used. Treatment with hydrochloric acid yielded the so-called gamma-variety while sulfuric acid tended to produce gamma- or alpha-MnO2. In addition, waste manganese sulfate obtained as by-product from sulfuric acid digestion treatment was recycled and electrolytically oxidized to gamma-MnO2. The discharge performance of the above-mentioned MnO2 samples as battery cathodic active material was evaluated and compared with the ordinary battery grade.

Modulated nematic structures induced by chirality and steric polarization

NASA Astrophysics Data System (ADS)

Longa, Lech; PajÄ k, Grzegorz

2016-04-01

What kind of one-dimensional modulated nematic structures (ODMNS) can form nonchiral and chiral bent-core and dimeric materials? Here, using the Landau-de Gennes theory of nematics, extended to account for molecular steric polarization, we study a possibility of formation of ODMNS, both in nonchiral and intrinsically chiral liquid crystalline materials. Besides nematic and cholesteric phases, we find four bulk ODMNS for nonchiral materials, two of which, to the best of our knowledge, have not been reported so far. These two structures are longitudinal (NLP) and transverse (NTP) periodic waves where the polarization field being periodic in one dimension stays parallel and perpendicular, respectively, to the wave vector. The other two phases are the twist-bend nematic phase (NTB) and the splay-bend nematic phase (NSB), but their fine structure appears more complex than that considered so far. The presence of molecular chirality converts nonchiral NTP and NSB into new NTB phases. Surprisingly, the nonchiral NLP phase can stay stable even in the presence of intrinsic chirality.

Framing the Discussion: Elections as Components of Larger Political and Cultural Geographies

ERIC Educational Resources Information Center

Knopp, Larry

2016-01-01

It is important to remember that elections are but one piece--albeit an important one--of much larger processes of politics and governance. Moreover, in the United States they are increasingly implicated in the construction of identities and places. What goes on in the course of electoral politics (creating electoral systems and voting districts,…

The Impact of Race and Ethnicity, Immigration and Political Context on Participation in American Electoral Politics

ERIC Educational Resources Information Center

Logan, John R.; Darrah, Jennifer; Oh, Sookhee

2012-01-01

This study uses national survey data in federal election years from 1996 through 2004 to examine voter registration and voting. It shows that racial/ethnic disparities in socio-economic resources and rootedness in the community do not explain overall group differences in electoral participation. It contradicts the expectation from an assimilation…

The Impact of Negative Income Tax on Participation in Electoral Politics.

ERIC Educational Resources Information Center

Heffernan, Joseph

This paper reports on the impact of the Rural Income Maintenance Experiment on participation in the electoral process. Paradigms of the left and of the right predict dramatically different consequences of universal income supplement, the left wing seeing such a program as essential for minimal democratic processes while the right sees in universal…

The Voting Rights Act and Black Electoral Participation.

ERIC Educational Resources Information Center

Thompson, Kenneth H.

An analysis of Census Bureau data on registration and voting by black citizens over the past two decades shows the positive influence of the 1965 Voting Rights Act on electoral participation. After the passage of the act, there was more than a 50% increase in the number of black registered voters. Of black and white citizens participating in the…

The Senate Electoral Cycle and Bicameral Appropriations Politics1

PubMed Central

Shepsle, Kenneth A.; Van Houweling, Robert P.; Abrams, Samuel J.; Hanson, Peter C.

2009-01-01

We consider the consequences of the Senate electoral cycle and bicameralism for distributive politics, introducing the concept of contested credit claiming, i.e. that members of a state’s House and Senate delegations must share the credit for appropriations that originate in their chamber with delegation members in the other chamber. Using data that isolates appropriations of each chamber, we test a model of the strategic incentives contested credit claiming creates. Our empirical analysis indicates that the Senate electoral cycle induces a back-loading of benefits to the end of senatorial terms, but that the House blunts this tendency with countercyclical appropriations. Our analysis informs our understanding of appropriations earmarking, and points a way forward in studying the larger consequences of bicameral legislatures. PMID:19543433

[Significance of endogenous sulfur dioxide in the regulation of cardiovascular system].

PubMed

Jin, Hong Fang; DU, Shu Xu; Zhao, Xia; Zhang, Su Qing; Tian, Yue; Bu, Ding Fang; Tang, Chao Shu; DU, Jun Bao

2007-08-18

Since the 1980's nitric oxide (NO), carbon monoxide (CO) and hydrogen sulfide (H(2)S), the endogenous gas molecules produced from metabolic pathway, have been realized as signal molecules to be involved in the regulation of body homeostasis and to play important roles under physiological and pathophysiological conditions. The researches on these endogenous gas signal molecules opened a new avenue in life science. To explore the new member of gasotransmitter family, other endogenous gas molecules which have been regarded as metabolic waste up to date, and their biological regulatory effects have been paid close attention to in the current fields of life science and medicine. Sulfur dioxide (SO(2)) can be produced endogenously from normal metabolism of sulfur-containing amino acids. L-cysteine is oxidized via cysteine dioxygenase to L-cysteinesulfinate, and the latter can proceed through transamination by glutamate oxaloacetate transaminase (GOT) to beta-sulfinyl pyruvate which decomposes spontaneously to pyruvate and SO(2). In mammals, activated neutrophils by oxidative stress can convert H(2)S to sulfite through a reduced form of nicotinamide-adenine dinucleotide phosphate (NADPH) oxidase-dependent process. The authors detected endogenous production of SO(2) in all cardiovascular tissues, including in heart, aorta, pulmonary artery, mesenteric artery, renal artery, tail artery and the plasma SO(2) content. As the key enzyme producing SO(2), GOT mRNA in cardiovascular system was detected and found to be located enriched in endothelial cells and vascular smooth muscle cells near the endothelial layer. When the normal rats were treated with hydroxamate(HDX), a GOT inhibitor, at a dose of 3.7 mg/kg body weight, the blood pressure (BP) went high markedly, the ratio of wall thickness to lumen radius was increased by 18.34%, and smooth muscle cell proliferation was enhanced. The plasma SO(2) level in the rats injected with 125 micromol/kg body weight SO(2) donor was increased to 721.98+/-30.11 micromol/L at the end of 30 seconds, while the blood pressure was decreased to the lowest point 65.0+/- 4.9 mm Hg at the end of 1 minute. The above results showed that endogenous SO(2) might be involved in the maintenance of blood pressure and normal vascular structure. In spontaneous hypertensive rat (SHR) animal model, exogenous supplement of SO(2) donor decreased the BP, the media cross-sectional area, and pressure of the media and the ratio of wall thickness to lumen radius in the SHR. Moreover, the proliferative index of aortic smooth muscle cells was decreased in the SHR treated with SO(2) donor compared with that in SHR. The above data showed that SO(2) could prevent the aortic structural remodeling by inhibiting the proliferation of aortic smooth muscle cells. The authors observed the direct vasorelaxant effects of SO(2) on the aortic ring pre-treated with norepinephrine (NE). SO(2) donor at a concentration of 25-100 micromol/L relaxed the aortic ring temporarily and slightly, but SO(2) donor at a concentration of 1-12 mmol/L induced relaxation of the ring in a concentration-dependent manner. Administration with nicardipine, an L-type calcium channel blocker other than glibenclamide, an ATP sensitive potassium channel (K(ATP) channel) blocker or removal of vascular endothelium could decrease the SO(2)-induced vasorelaxation. In hypoxic pulmonary hypertension animal model, SO(2) donor decreased the mean pulmonary artery pressure and the systolic pulmonary artery pressure (P<0.01), respectively as compared with hypoxic group, and alleviated obviously the hypoxic pulmonary vascular structural remodeling. The percentage of muscularized arteries of small pulmonary vessels was significantly decreased in hypoxia+SO(2) donor-treated rats compared with that of hypoxic rats (P<0.01), while the percentage of non-muscularized vessels was obviously higher in hypoxia with SO(2) donor-treated rats than that of hypoxic rats (P<0.01). Similarly, SO(2) obviously decreased relative media area and relative media thickness of small muscularized pulmonary arteries in hypoxic rats (P<0.01). The above data showed that SO(2) might play an important role in development of hypoxic pulmonary hypertension. Perfusion with SO(2) donor (10(-6)-10(-3) mol/L) to the isolated rat heart obviously inhibited the left ventricular peak rate of contraction ( + LV dp/ dtmax) , peak rate of relaxation (-LV dp/ dtmax) and difference of left ventricular pressure ( DeltaLVP) in a concentration dependent manner. Nicardipine, an L-type calcium channel blocker, could partly antagonize the inhibitory effect of SO(2) on the heart function. In a word, SO(2) could be endogenously generated in cardiovascular tissues and exert important cardiovascular effects such as vasorelaxant effect and negative inotropic effects. Moreover, SO(2) might play considerable roles in the regulation of systemic circulatory pressure, pulmonary circulatory pressure and vascular structural remodeling in the pathogenesis of hypertension and hypoxic pulmonary hypertension. On the basis of the above findings, we presumed that endogenous SO(2) might be a novel cardiovascular functional regulatory gasotransmitter. More studies on the significance of endogenous SO(2) in cardiovascular system under physiological and pathophysiological conditions need to be investigated.

Design and modelling of high gain DC-DC converters for fuel cell hybrid electric vehicles

NASA Astrophysics Data System (ADS)

Elangovan, D.; Karthigeyan, V.; Subhanu, B.; Ashwin, M.; Arunkumar, G.

2017-11-01

Transportation (Diesel and petrol internal combustion engine vehicles) approximately contributes to 25.5% of total CO2 emission. Thus diesel and petrol engine vehicles are the most dominant contributors of CO2 emission which leads global warming which causes climate change. The problem of CO2 emission and global warming can be reduced by focusing on renewable energy vehicles. Out of the available renewable energy sources fuel cell is the only source which has reasonable efficiency and can be used in vehicles. But the main disadvantage of fuel cell is its slow response time. So energy storage systems like batteries and super capacitors are used in parallel with the fuel cell. Fuel cell is used during steady state vehicle operation while during transient conditions like starting, acceleration and braking batteries and super capacitors can supply or absorb energy. In this paper a unidirectional fuel cell DC-DC converter and bidirectional energy storage system DC-DC converter is proposed, which can interface dc sources at different voltage levels to the dc bus and also it can independently control the power flow from each energy source to the dc bus and vice versa. The proposed converters are designed and simulated using PSIM version 9.1.1 and gate pulse pattern, input and output voltage waveforms of the converters for steady state operation are studied.

Ferric iron-bearing sediments as a mineral trap for CO2 sequestration: Iron reduction using sulfur-bearing waste gas

USGS Publications Warehouse

Palandri, J.L.; Kharaka, Y.K.

2005-01-01

We present a novel method for geologic sequestration of anthropogenic CO2 in ferrous carbonate, using ferric iron present in widespread redbeds and other sediments. Iron can be reduced by SO2 that is commonly a component of flue gas produced by combustion of fossil fuel, or by adding SO2 or H2S derived from other industrial processes to the injected waste gas stream. Equilibrium and kinetically controlled geochemical simulations at 120 bar and 50 and 100 ??C with SO2 or H2S show that iron can be transformed almost entirely to siderite thereby trapping CO2, and simultaneously, that sulfur can be converted predominantly to dissolved sulfate. If there is an insufficient amount of sulfur-bearing gas relative to CO2 as for typical flue gas, then some of the iron is not reduced, and some of the CO2 is not sequestered. If there is an excess of sulfur-bearing gas, then complete iron reduction is ensured, and some of the iron precipitates as pyrite or other solid iron sulfide, depending on their relative precipitation kinetics. Gas mixtures with insufficient sulfur relative to CO2 can be used in sediments containing Ca, Mg, or other divalent metals capable of precipitating carbonate minerals. For quartz arenite with an initial porosity of 21% and containing 0.25 wt.% Fe2O3, approximately 0.7 g of CO2 is sequestered per kg of rock, and the porosity decrease is less than 0.03%. Sequestration of CO2 using ferric iron has the advantage of disposing of SO2 that may already be present in the combustion gas. ?? 2005 Published by Elsevier B.V.

Step-and-Repeat Nanoimprint-, Photo- and Laser Lithography from One Customised CNC Machine.

PubMed

Greer, Andrew Im; Della-Rosa, Benoit; Khokhar, Ali Z; Gadegaard, Nikolaj

2016-12-01

The conversion of a computer numerical control machine into a nanoimprint step-and-repeat tool with additional laser- and photolithography capacity is documented here. All three processes, each demonstrated on a variety of photoresists, are performed successfully and analysed so as to enable the reader to relate their known lithography process(es) to the findings. Using the converted tool, 1 cm(2) of nanopattern may be exposed in 6 s, over 3300 times faster than the electron beam equivalent. Nanoimprint tools are commercially available, but these can cost around 1000 times more than this customised computer numerical control (CNC) machine. The converted equipment facilitates rapid production and large area micro- and nanoscale research on small grants, ultimately enabling faster and more diverse growth in this field of science. In comparison to commercial tools, this converted CNC also boasts capacity to handle larger substrates, temperature control and active force control, up to ten times more curing dose and compactness. Actual devices are fabricated using the machine including an expanded nanotopographic array and microfluidic PDMS Y-channel mixers.

CMOS based capacitance to digital converter circuit for MEMS sensor

NASA Astrophysics Data System (ADS)

Rotake, D. R.; Darji, A. D.

2018-02-01

Most of the MEMS cantilever based system required costly instruments for characterization, processing and also has large experimental setups which led to non-portable device. So there is a need of low cost, highly sensitive, high speed and portable digital system. The proposed Capacitance to Digital Converter (CDC) interfacing circuit converts capacitance to digital domain which can be easily processed. Recent demand microcantilever deflection is part per trillion ranges which change the capacitance in 1-10 femto farad (fF) range. The entire CDC circuit is designed using CMOS 250nm technology. Design of CDC circuit consists of a D-latch and two oscillators, namely Sensor controlled oscillator (SCO) and digitally controlled oscillator (DCO). The D-latch is designed using transmission gate based MUX for power optimization. A CDC design of 7-stage, 9-stage and 11-stage tested for 1-18 fF and simulated using mentor graphics Eldo tool with parasitic. Since the proposed design does not use resistance component, the total power dissipation is reduced to 2.3621 mW for CDC designed using 9-stage SCO and DCO.

Step-and-Repeat Nanoimprint-, Photo- and Laser Lithography from One Customised CNC Machine

NASA Astrophysics Data System (ADS)

Greer, Andrew IM; Della-Rosa, Benoit; Khokhar, Ali Z.; Gadegaard, Nikolaj

2016-03-01

The conversion of a computer numerical control machine into a nanoimprint step-and-repeat tool with additional laser- and photolithography capacity is documented here. All three processes, each demonstrated on a variety of photoresists, are performed successfully and analysed so as to enable the reader to relate their known lithography process(es) to the findings. Using the converted tool, 1 cm2 of nanopattern may be exposed in 6 s, over 3300 times faster than the electron beam equivalent. Nanoimprint tools are commercially available, but these can cost around 1000 times more than this customised computer numerical control (CNC) machine. The converted equipment facilitates rapid production and large area micro- and nanoscale research on small grants, ultimately enabling faster and more diverse growth in this field of science. In comparison to commercial tools, this converted CNC also boasts capacity to handle larger substrates, temperature control and active force control, up to ten times more curing dose and compactness. Actual devices are fabricated using the machine including an expanded nanotopographic array and microfluidic PDMS Y-channel mixers.

User's guide for MAGIC-Meteorologic and hydrologic genscn (generate scenarios) input converter

USGS Publications Warehouse

Ortel, Terry W.; Martin, Angel

2010-01-01

Meteorologic and hydrologic data used in watershed modeling studies are collected by various agencies and organizations, and stored in various formats. Data may be in a raw, un-processed format with little or no quality control, or may be checked for validity before being made available. Flood-simulation systems require data in near real-time so that adequate flood warnings can be made. Additionally, forecasted data are needed to operate flood-control structures to potentially mitigate flood damages. Because real-time data are of a provisional nature, missing data may need to be estimated for use in floodsimulation systems. The Meteorologic and Hydrologic GenScn (Generate Scenarios) Input Converter (MAGIC) can be used to convert data from selected formats into the Hydrologic Simulation System-Fortran hourly-observations format for input to a Watershed Data Management database, for use in hydrologic modeling studies. MAGIC also can reformat the data to the Full Equations model time-series format, for use in hydraulic modeling studies. Examples of the application of MAGIC for use in the flood-simulation system for Salt Creek in northeastern Illinois are presented in this report.

Data reduction software for LORAN-C flight test evaluation

NASA Technical Reports Server (NTRS)

Fischer, J. P.

1979-01-01

A set of programs designed to be run on an IBM 370/158 computer to read the recorded time differences from the tape produced by the LORAN data collection system, convert them to latitude/longitude and produce various plotting input files are described. The programs were written so they may be tailored easily to meet the demands of a particular data reduction job. The tape reader program is written in 370 assembler language and the remaining programs are written in standard IBM FORTRAN-IV language. The tape reader program is dependent upon the recording format used by the data collection system and on the I/O macros used at the computing facility. The other programs are generally device-independent, although the plotting routines are dependent upon the plotting method used. The data reduction programs convert the recorded data to a more readily usable form; convert the time difference (TD) numbers to latitude/longitude (lat/long), to format a printed listing of the TDs, lat/long, reference times, and other information derived from the data, and produce data files which may be used for subsequent plotting.

A genetic screen reveals a periplasmic copper chaperone required for nitrite reductase activity in pathogenic Neisseria.

PubMed

Jen, Freda E-C; Djoko, Karrera Y; Bent, Stephen J; Day, Christopher J; McEwan, Alastair G; Jennings, Michael P

2015-09-01

Under conditions of low oxygen availability, Neisseria meningitidis and Neisseria gonorrhoeae are able to respire via a partial denitrification pathway in which nitrite is converted to nitrous oxide. In this process, nitrite reductase (AniA), a copper (Cu)-containing protein converts nitrite to NO, and this product is converted to nitrous oxide by nitric oxide reductase (NorB). NorB also confers protection against toxic NO, and so we devised a conditional lethal screen, using a norB mutant, to identify mutants that were resistant to nitrite-dependent killing. After random-deletion mutagenesis of N. meningitidis, this genetic screen identified a gene encoding a Cu chaperone that is essential for AniA function, AccA. Purified AccA binds one Cu (I) ion and also possesses a second binding site for Cu (II). This novel periplasmic Cu chaperone (AccA) appears to be essential for provision of Cu ions to AniA of pathogenic Neisseria to generate an active nitrite reductase. Apart from the Neisseria genus, AccA is distributed across a wide range of environmental Proteobacteria species. © FASEB.

Production of Furfural from Process-Relevant Biomass-Derived Pentoses in a Biphasic Reaction System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mittal, Ashutosh; Black, Stuart K.; Vinzant, Todd B.

Furfural is an important fuel precursor which can be converted to hydrocarbon fuels and fuel intermediates. In this work, the production of furfural by dehydration of process-relevant pentose rich corn stover hydrolyzate using a biphasic batch reaction system has been investigated. Methyl isobutyl ketone (MIBK) and toluene have been used to extract furfural and enhance overall furfural yield by limiting its degradation to humins. The effects of reaction time, temperature, and acid concentration (H 2SO 4) on pentose conversion and furfural yield were investigated. For the dehydration of 8 wt % pentose-rich corn stover hydrolyzate under optimum reaction conditions, 0.05more » M H 2SO 4, 170 degrees C for 20 min with MIBK as the solvent, complete conversion of xylose (98-100%) and a furfural yield of 80% were obtained. Under these same conditions, except with toluene as the solvent, the furfural yield was 77%. Additionally, dehydration of process-relevant pentose rich corn stover hydrolyzate using solid acid ion-exchange resins under optimum reaction conditions has shown that Purolite CT275 is as effective as H 2SO 4 for obtaining furfural yields approaching 80% using a biphasic batch reaction system. In conclusion, this work has demonstrated that a biphasic reaction system can be used to process biomass-derived pentose rich sugar hydrolyzates to furfural in yields approaching 80%.« less

An optimized prototype of electromagnetic calorimeter for the SoLID project at Jefferson Lab

NASA Astrophysics Data System (ADS)

Shen, C.; Wang, Y.; Xiao, D.; Han, D.; Zou, Z.; Li, Y.; Zheng, X.; Chen, J.

2018-02-01

A shashlik-type electromagnetic calorimeter will be produced in Hall A of Jefferson Laboratory for the Solenoidal Large Intensity Device (SoLID). Wavelength-shifting (WLS) fibers and clear fibers will be used as the light guide part of the calorimeter. The blue light from scintillators is converted into green light by WLS fibers and is carried out to the back of the calorimeters for readout. Since the magnetic field of SoLID reaches about 1.5 T behind the calorimeters, the design is to use clear fibers to further guide the light out of the solenoid for readout by PMTs. Therefore, it is important to study the perfomance of WLS and clear fibers. This paper describes a comparative test of two different WLS fibers and a light attenuation test for a clear fiber. The results show that the performance of the two WLS fibers is the same under large curvature bending, and that the bending has no effect on the light transmission through the clear fiber. In addition, a comparison test for two fiber end-face reflective materials is also reported. It reveals that the use of silver ink as a reflective material can increase the light yield by 30%. Thereby, an optimized prototype based on the above experimental results was built and the basic performance was tested.

Waste oil shale ash as a novel source of calcium for precipitated calcium carbonate: carbonation mechanism, modeling, and product characterization.

PubMed

Velts, O; Uibu, M; Kallas, J; Kuusik, R

2011-11-15

In this paper, a method for converting lime-containing oil shale waste ash into precipitated calcium carbonate (PCC), a valuable commodity is elucidated. The mechanism of ash leachates carbonation was experimentally investigated in a stirred semi-batch barboter-type reactor by varying the CO(2) partial pressure, gas flow rate, and agitation intensity. A consistent set of model equations and physical-chemical parameters is proposed to describe the CaCO(3) precipitation process from oil shale ash leachates of complex composition. The model enables the simulation of reactive species (Ca(2+), CaCO(3), SO(4)(2-), CaSO(4), OH(-), CO(2), HCO(3)(-), H(+), CO(3)(2-)) concentration profiles in the liquid, gas, and solid phases as well as prediction of the PCC formation rate. The presence of CaSO(4) in the product may also be evaluated and used to assess the purity of the PCC product. A detailed characterization of the PCC precipitates crystallized from oil shale ash leachates is also provided. High brightness PCC (containing up to ∼ 96% CaCO(3)) with mean particle sizes ranging from 4 to 10 μm and controllable morphology (such as rhombohedral calcite or coexisting calcite and spherical vaterite phases) was obtained under the conditions studied. Copyright © 2011 Elsevier B.V. All rights reserved.

Utilization of waste as biogas substrateby dominan microbes identified

NASA Astrophysics Data System (ADS)

Nurlina, E.; Sambasri, S.; Hartati, E.; Safitri, R.; Hodijat, A.

2018-05-01

Indonesia as the tropics have a source of biomass feedstock which is very large, so the waste biomass can be used optimally as an energy source in the form of biogas. This study was conducted to obtain alternative energy from domestic waste materials, given the limited availability of petroleum and natural gas sourced from fossil fuels. This methodology is an experimental method, the process conditions at room temperature 25-27 °C, pH adjusted to the growth of microbes to produce biogas, retention time 20-60 days, the bioreactor is operated with a batch system, the volume of waste in the bioreactor is made permanent, so that the production of biogas in large scale will increase the pressure inside the bioreactor. Biogas is formed accommodated then distributed to the stove. Factors that determine the formation of biogas is a microbial species capable methanogens convert acetate into biogas. From the results of microbial identification of the isolates in the bioreactor, has identified three types of bacteria methanogens namely Methanospirillum hungatei, Methanobacterium polustre and Methanolacinapoynteri. The results of this study, domestic waste can be utilized as a substrate in biogas production, with the highest methane composition reaches 50.79%. This result is expected to increase public knowledge to utilize the waste into biogas as a renewable energy to sufficient the energy needs of household, so it does not depend on the energy derived from fossil fuels.

Uptake of HNO3 on aviation kerosene and aircraft engine soot: influences of H2O or/and H2SO4.

PubMed

Loukhovitskaya, Ekaterina E; Talukdar, Ranajit K; Ravishankara, A R

2013-06-13

The uptake of HNO3 on aviation kerosene soot (TC-1 soot) was studied in the absence and presence of water vapor at 295 and 243 K. The influence of H2SO4 coating of the TC-1 soot surface on HNO3 uptake was also investigated. Only reversible uptake of HNO3 was observed. HONO and NO2, potential products of reactive uptake of HNO3, were not observed under any conditions studied here. The uptake of nitric acid increased slightly with relative humidity (RH). Coating of the TC-1 soot surface with sulfuric acid decreased the uptake of HNO3 and did not lead to displacement of H2SO4 from the soot surface. A limited set of measurements was carried out on soot generated by aircraft engine combustor (E-soot) with results similar to those on TC-1 soot. The influence of water on HNO3 uptake on E-soot appeared to be more pronounced than on TC-1 soot. Our results suggest that HNO3 loss in the upper troposphere due to soot is not significant except perhaps in aircraft exhaust plumes. Our results also suggest that HNO3 is not converted to either NO2 or HONO upon its uptake on soot in the atmosphere.

Estimating surface NO2 and SO2 mixing ratios from fast-response total column observations and potential application to geostationary missions.

PubMed

Knepp, T; Pippin, M; Crawford, J; Chen, G; Szykman, J; Long, R; Cowen, L; Cede, A; Abuhassan, N; Herman, J; Delgado, R; Compton, J; Berkoff, T; Fishman, J; Martins, D; Stauffer, R; Thompson, A M; Weinheimer, A; Knapp, D; Montzka, D; Lenschow, D; Neil, D

Total-column nitrogen dioxide (NO 2 ) data collected by a ground-based sun-tracking spectrometer system (Pandora) and an photolytic-converter-based in-situ instrument collocated at NASA's Langley Research Center in Hampton, Virginia were analyzed to study the relationship between total-column and surface NO 2 measurements. The measurements span more than a year and cover all seasons. Surface mixing ratios are estimated via application of a planetary boundary-layer (PBL) height correction factor. This PBL correction factor effectively corrects for boundary-layer variability throughout the day, and accounts for up to ≈75 % of the variability between the NO 2 data sets. Previous studies have made monthly and seasonal comparisons of column/surface data, which has shown generally good agreement over these long average times. In the current analysis comparisons of column densities averaged over 90 s and 1 h are made. Applicability of this technique to sulfur dioxide (SO 2 ) is briefly explored. The SO 2 correlation is improved by excluding conditions where surface levels are considered background. The analysis is extended to data from the July 2011 DISCOVER-AQ mission over the greater Baltimore, MD area to examine the method's performance in more-polluted urban conditions where NO 2 concentrations are typically much higher.

Production of Furfural from Process-Relevant Biomass-Derived Pentoses in a Biphasic Reaction System

DOE PAGES

Mittal, Ashutosh; Black, Stuart K.; Vinzant, Todd B.; ...

2017-05-16

Furfural is an important fuel precursor which can be converted to hydrocarbon fuels and fuel intermediates. In this work, the production of furfural by dehydration of process-relevant pentose rich corn stover hydrolyzate using a biphasic batch reaction system has been investigated. Methyl isobutyl ketone (MIBK) and toluene have been used to extract furfural and enhance overall furfural yield by limiting its degradation to humins. The effects of reaction time, temperature, and acid concentration (H 2SO 4) on pentose conversion and furfural yield were investigated. For the dehydration of 8 wt % pentose-rich corn stover hydrolyzate under optimum reaction conditions, 0.05more » M H 2SO 4, 170 degrees C for 20 min with MIBK as the solvent, complete conversion of xylose (98-100%) and a furfural yield of 80% were obtained. Under these same conditions, except with toluene as the solvent, the furfural yield was 77%. Additionally, dehydration of process-relevant pentose rich corn stover hydrolyzate using solid acid ion-exchange resins under optimum reaction conditions has shown that Purolite CT275 is as effective as H 2SO 4 for obtaining furfural yields approaching 80% using a biphasic batch reaction system. In conclusion, this work has demonstrated that a biphasic reaction system can be used to process biomass-derived pentose rich sugar hydrolyzates to furfural in yields approaching 80%.« less

Aromatic polyimides containing a dimethylsilane-linked dianhydride

NASA Technical Reports Server (NTRS)

St.clair, Anne K. (Inventor); St.clair, Terry L. (Inventor); Pratt, J. Richard (Inventor)

1989-01-01

A high-temperature stable, optically transparent, low dielectric aromatic polyimide is prepared by chemically combining equimolar quantities of an aromatic dianhydride reactant and an aromatic diamine reactant, which are selected so that one reactant contains at least one Si(CH3)2 group in its molecular structure, and the other reactant contains at least one -CF3 group in its molecular structure. The reactants are chemically combined in a solvent medium to form a solution of a high molecular weight polyamic acid, which is then converted to the corresponding polyimide.

Aromatic polyimides containing a dimethylsilane-linked dianhydride

NASA Technical Reports Server (NTRS)

St. Clair, Anne K. (Inventor); St. Clair, Terry L. (Inventor); Pratt, J. Richard (Inventor)

1992-01-01

A high-temperature stable, optically transparent, low dielectric aromatic polyimide is prepared by chemically combining equimolar quantities of an aromatic dianhydride reactant and an aromatic diamine reactant, which are selected so that one reactant contains at least one Si(CH.sub.3).sub.2 group in its molecular structure, and the other reactant contains at least one --CH.sub.3 group in its molecular structure. The reactants are chemically combined in a solvent medium to form a solution of a high molecular weight polyamic acid, which is then converted to the corresponding polyimide.

Thermionic converter temperature controller

DOEpatents

Shaner, Benjamin J [McMurray, PA; Wolf, Joseph H [Pittsburgh, PA; Johnson, Robert G. R. [Trafford, PA

2001-04-24

A method and apparatus for controlling the temperature of a thermionic reactor over a wide range of operating power, including a thermionic reactor having a plurality of integral cesium reservoirs, a honeycomb material disposed about the reactor which has a plurality of separated cavities, a solid sheath disposed about the honeycomb material and having an opening therein communicating with the honeycomb material and cavities thereof, and a shell disposed about the sheath for creating a coolant annulus therewith so that the coolant in the annulus may fill the cavities and permit nucleate boiling during the operation of the reactor.

Putting on a clinic in Va. Carilion, a not-for-profit hospital system based in Roanoke, is taking a $100 million risk to become a physician-run venture.

PubMed

Evans, Melanie

2006-06-26

Carilion Health System needs to change or die, according to its leaders, so the Roanoke, Va., organization is converting from a typical not-for-profit system into a physician-run clinic. The switch is an extreme version of an industrywide push to employ doctors. James Thweatt Jr., left, of rival Lewis-Gale, says his hospital joined the trend when it hired 80 specialists from a failing local clinic.

An Incremental Language Conversion Method to Convert C++ into Ada95

DTIC Science & Technology

1996-12-01

P.J. Deitel , C++ How to Program , Prentice Hall, Englewood Cliffs, NY, 1994. [Dewar94] Robert Dewar, "The GNAT Compilation Model", Proceedings of the...example of how to use GNAT’s C++ low-level interface capabilities to interface an Ada tagged type from C++ programs . Figure I-1 shows the package...husband the best of lucks. I also wish my younger sister, Su- How Sheu, the best of luck in starting her family. iii11 There are so many people I need to

Corrosion-resistant uranium

DOEpatents

Hovis, V.M. Jr.; Pullen, W.C.; Kollie, T.G.; Bell, R.T.

1981-10-21

The present invention is directed to the protecting of uranium and uranium alloy articles from corrosion by providing the surfaces of the articles with a layer of an ion-plated metal selected from aluminum and zinc to a thickness of at least 60 microinches and then converting at least the outer surface of the ion-plated layer of aluminum or zinc to aluminum chromate or zinc chromate. This conversion of the aluminum or zinc to the chromate form considerably enhances the corrosion resistance of the ion plating so as to effectively protect the coated article from corrosion.

Disk tides and accretion runaway

NASA Technical Reports Server (NTRS)

Ward, William R.; Hahn, Joseph M.

1995-01-01

It is suggested that tidal interaction of an accreting planetary embryo with the gaseous preplanetary disk may provide a mechanism to breach the so-called runaway limit during the formation of the giant planet cores. The disk tidal torque converts a would-be shepherding object into a 'predator,' which can continue to cannibalize the planetesimal disk. This is more likely to occur in the giant planet region than in the terrestrial zone, providing a natural cause for Jupiter to predate the inner planets and form within the O(10(exp 7) yr) lifetime of the nebula.

Generalized Choi states and 2-distillability of quantum states

NASA Astrophysics Data System (ADS)

Chen, Lin; Tang, Wai-Shing; Yang, Yu

2018-05-01

We investigate the distillability of bipartite quantum states in terms of positive and completely positive maps. We construct the so-called generalized Choi states and show that it is distillable when it has negative partial transpose. We convert the distillability problem of 2-copy n× n Werner states into the determination of the positivity of an Hermitian matrix. We obtain several sufficient conditions by which the positivity holds. Further, we investigate the case n=3 by the classification of 2× 3× 3 pure states.

Corrosion-resistant uranium

DOEpatents

Hovis, Jr., Victor M.; Pullen, William C.; Kollie, Thomas G.; Bell, Richard T.

1983-01-01

The present invention is directed to the protecting of uranium and uranium alloy articles from corrosion by providing the surfaces of the articles with a layer of an ion-plated metal selected from aluminum and zinc to a thickness of at least 60 microinches and then converting at least the outer surface of the ion-plated layer of aluminum or zinc to aluminum chromate or zinc chromate. This conversion of the aluminum or zinc to the chromate form considerably enhances the corrosion resistance of the ion plating so as to effectively protect the coated article from corrosion.

MBASIC batch processor architectural overview

NASA Technical Reports Server (NTRS)

Reynolds, S. M.

1978-01-01

The MBASIC (TM) batch processor, a language translator designed to operate in the MBASIC (TM) environment is described. Features include: (1) a CONVERT TO BATCH command, usable from the ready mode; and (2) translation of the users program in stages through several levels of intermediate language and optimization. The processor is to be designed and implemented in both machine-independent and machine-dependent sections. The architecture is planned so that optimization processes are transparent to the rest of the system and need not be included in the first design implementation cycle.

Reactivity of stratospheric aerosols to small amounts of ammonia in the laboratory environment

NASA Technical Reports Server (NTRS)

Hayes, D.; Snetsinger, K.; Ferry, G.; Oberbeck, V.; Farlow, N.

1980-01-01

Trace ammonia in laboratory air reacts easily with sulfuric acid aerosol samples to form crystalline ammonium sulfate. Argon atmospheres, however, protect sampling surfaces from ammonia contamination. It is found that atmospheric aerosols treated in this way contain only sulfuric acid. After an hour exposed to laboratory air, these same samples convert to ammonium sulfate. Aerosol particles have been collected, using argon control, to determine if the absence of crystalline sulfate is common. But so far there is no evidence that aerosols are neutralized by ammonia in the stratosphere.

Voter Education Manual for Secondary Schools and a Teacher's Guide to Student Handouts in the Voter Education Manual.

ERIC Educational Resources Information Center

Balasco, Alfred P.; And Others

This classroom guide instructs secondary school students about the registration process, the voting process, and the importance of the American electoral system. The goal is to encourage students to participate in the electoral process. Although the guide focuses most heavily on the specifics of voter education in Rhode Island, it is also…

Hizb ut-Tahrir: A Threat Behind a Legal Facade?

DTIC Science & Technology

2006-06-01

as something “man-made,’ humanly derived and “un-Islamic,” and therefore, does not participate in any secular electoral process . However, HT does...derived and “un-Islamic,” and therefore, does not participate in any secular electoral process . However, HT does not reject modern technology and its...2. The Evolutionary Process of Jihad Interpretations ..........................................62 x

Different isotope and chemical patterns of pyrite oxidation related to lag and exponential growth phases of Acidithiobacillus ferrooxidans reveal a microbial growth strategy

NASA Astrophysics Data System (ADS)

Brunner, Benjamin; Yu, Jae-Young; Mielke, Randall E.; MacAskill, John A.; Madzunkov, Stojan; McGenity, Terry J.; Coleman, Max

2008-06-01

The solution chemistry during the initial (slow increase of dissolved iron and sulfate) and main stage (rapid increase of dissolved iron and sulfate) of pyrite leaching by Acidithiobacillus ferrooxidans (Af) at a starting pH of 2.05 shows significant differences. During the initial stage, ferrous iron (Fe2+) is the dominant iron species in solution and the molar ratio of produced sulfate (SO42-) and total iron (Fetot) is 1.1, thus does not reflect the stoichiometry of pyrite (FeS2). During the main stage, ferric iron (Fe3+) is the dominant iron species in solution and the SO42-:Fetot ratio is with 1.9, close to the stoichiometry of FeS2. Another difference between initial and main stage is an initial trend to slightly higher pH values followed by a drop during the main stage to pH 1.84. These observations raise the question if there are different modes of bioleaching of pyrite, and if there are, what those modes imply in terms of leaching mechanisms. Different oxygen and sulfur isotope trends of sulfate during the initial and main stages of pyrite oxidation confirm that there are two pyrite bioleaching modes. The biochemical reactions during initial stage are best explained by the net reaction FeS2 + 3O2 ⇒ Fe2+ + SO42- + SO2(g). The degassing of sulfur dioxide (SO2) acts as sink for sulfur depleted in 34S compared to pyrite, and is the cause of the SO42-:Fetot ratio of 1.1 and the near constant pH. During the exponential phase, pyrite sulfur is almost quantitatively converted to sulfate, according to the net reaction FeS2 + 15/4O2 + 1/2H2O ⇒ Fe3+ + 2SO42- + H+. We hypothesize that the transition between the modes of bioleaching of pyrite is due to the impact of the accumulation of ferrous iron, which induces changes in the metabolic activity of Af and may act as an inhibitor for the oxidation of sulfur species. This transition defines a fundamental change in the growth strategy of Af. A mode, where bacteria gain energy by oxidation of elemental sulfur to sulfite but show little growth is switched into a mode, where bacteria gain a smaller amount of energy by the oxidation of ferrous iron, but induce much faster pyrite leaching rates due to the production of ferric iron.

Transnational networks, diffusion dynamics, and electoral revolutions in the postcommunist world

NASA Astrophysics Data System (ADS)

Bunce, Valerie; Wolchik, Sharon L.

2007-05-01

Since 1996, eight elections have taken place in postcommunist Europe and Eurasia that have replaced illiberal with liberal governments. There is ample evidence that these “electoral revolutions” reflected the cross-national diffusion of a distinctive model of regime change that was developed elsewhere and that was designed to promote democratization in authoritarian political contexts featuring semi-competitive elections. This electoral model spread throughout the postcommunist region because of both shared perceptions by opposition groups of similar local conditions and the existence of transnational democracy promotion networks that included local, regional and American participants. As these revolutions spread, however, they were less successful in carrying through democratic change-in part because local conditions were less supportive and in part because authoritarian leaders and their international allies were both forewarned and forearmed.

Affect in electoral politics.

PubMed

Glaser, J; Salovey, P

1998-01-01

Recent U.S. history provides vivid illustrations of the importance of politicians' emotional displays in subsequent judgments of them. Yet, a review of empirical research on the role of affect (emotion, mood, and evaluation) in electoral politics reveals little work that has focused on the impact of candidates' emotional expression on voters' preferences for them. A theoretical framework is proposed to identify psychological mechanisms by which a target's displays of emotion influence judgments of that target. Findings from the emerging literature on emotions and politics challenge the traditional assumption of political science that voters make decisions based solely on the cold consideration of nonaffectively charged information. The affect and politics literature, although somewhat unfocused and broad, represents an interdisciplinary domain of study that contributes to the understanding of both electoral politics and social interaction more generally.

Testing CuO nanowires as a novel X-ray to electron converter for gas-filled radiation detectors

NASA Astrophysics Data System (ADS)

Zarei, H.; Saramad, S.; Razaghi, S.

2017-10-01

Nanowires, due to their special physical properties and also high surface to volume ratio, can have considerable applications in designing and development of novel nanodevices. For the radiation shielding, higher absorption coefficient of nanostructures in comparison to bulk ones is an advantage. In gas detectors, designing a proper converter that absorbs higher energy of gamma and X-rays and convert it to more free electrons is one of the major problems. Since the nanowires have higher surface to volume ratio in comparison to the bulk one, so it is expected that by optimizing the thickness, the generated electrons can have higher chance to escape from the surface. In this work, the random CuO nanowires with diameter of 40 nm are deposited on thin glass slide. This nanostructure with different thicknesses are tested by plastic and CsI scintillators by X-ray tube with HVs in the range of 16 to 25 kV. The results show that for the same thickness, the CuO nanowires can release electrons six times more than the bulk ones and for the same energy the optimum QE of nanoconverter can be three times greater than the bulk converter. This novel nanoconverter with higher detection efficiency can have applications in high energy physics, medical imaging and also astronomy.

Model Predictive Control of A Matrix-Converter Based Solid State Transformer for Utility Grid Interaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xue, Yaosuo

The matrix converter solid state transformer (MC-SST), formed from the back-to-back connection of two three-to-single-phase matrix converters, is studied for use in the interconnection of two ac grids. The matrix converter topology provides a light weight and low volume single-stage bidirectional ac-ac power conversion without the need for a dc link. Thus, the lifetime limitations of dc-bus storage capacitors are avoided. However, space vector modulation of this type of MC-SST requires to compute vectors for each of the two MCs, which must be carefully coordinated to avoid commutation failure. An additional controller is also required to control power exchange betweenmore » the two ac grids. In this paper, model predictive control (MPC) is proposed for an MC-SST connecting two different ac power grids. The proposed MPC predicts the circuit variables based on the discrete model of MC-SST system and the cost function is formulated so that the optimal switch vector for the next sample period is selected, thereby generating the required grid currents for the SST. Simulation and experimental studies are carried out to demonstrate the effectiveness and simplicity of the proposed MPC for such MC-SST-based grid interfacing systems.« less

Enzymatic activity and partial purification of solanapyrone synthase: first enzyme catalyzing Diels-Alder reaction.

PubMed

Katayama, K; Kobayashi, T; Oikawa, H; Honma, M; Ichihara, A

1998-05-19

In cell-free extracts of Alternaria solani, an enzymatic activity converting prosolanapyrone II to solanapyrones A and D via oxidation and subsequent Diels-Alder reaction has been found. Chromatography with DEAE-Sepharose provided two active fractions, pools 1 and 2. The former fraction converted prosolanapyrone II to solanapyrones A and D in a ratio of 2.2:1 with optical purities of 99% and 45% ee, respectively. The latter fraction did so in a ratio of 7.6:1 with 99% and nearly 0% ee, respectively. The enzyme partially purified from pool 2 native molecular weight of 40-62 kD and a pl of 4.25. The high reactivity of prosolanapyrone III in aqueous solution and the chromatographic behavior of the enzyme in pool 2 suggest that a single enzyme catalyzes both the oxidation and Diels-Alder reaction.

Electrochemical separation and concentration of hydrogen sulfide from gas mixtures

DOEpatents

Winnick, Jack; Sather, Norman F.; Huang, Hann S.

1984-10-30

A method of removing sulfur oxides of H.sub.2 S from high temperature gas mixtures (150.degree.-1000.degree. C.) is the subject of the present invention. An electrochemical cell is employed. The cell is provided with inert electrodes and an electrolyte which will provide anions compatible with the sulfur containing anions formed at the anode. The electrolyte is also selected to provide inert stable cations at the temperatures encountered. The gas mixture is passed by the cathode where the sulfur gases are converted to SO.sub.4 -- or, in the case of H.sub.2 S, to S--. The anions migrate to the anode where they are converted to a stable gaseous form at much greater concentration levels (>10X). Current flow may be effected by utilizing an external source of electrical energy or by passing a reducing gas such as hydrogen past the anode.

ELECTROCHEMICAL SEPARATION AND CONCENTRATION OF HYDROGEN SULFIDE FROM GAS MIXTURES

DOEpatents

Winnick, Jack; Sather, Norman F.; Huang, Hann S.

1984-10-30

A method of removing sulfur oxides of H.sub.2 S from high temperature gas mixtures (150.degree.-1000.degree. C.) is the subject of the present invention. An electrochemical cell is employed. The cell is provided with inert electrodes and an electrolyte which will provide anions compatible with the sulfur containing anions formed at the anode. The electrolyte is also selected to provide inert stable cations at the temperatures encountered. The gas mixture is passed by the cathode where the sulfur gases are converted to SO.sub.4 -- or, in the case of H.sub.2 S, to S--. The anions migrate to the anode where they are converted to a stable gaseous form at much greater concentration levels (>10X). Current flow may be effected by utilizing an external source of electrical energy or by passing a reducing gas such as hydrogen past the anode.

Highly efficient all-nitride phosphor-converted white light emitting diode

NASA Astrophysics Data System (ADS)

Mueller-Mach, Regina; Mueller, Gerd; Krames, Michael R.; Höppe, Henning A.; Stadler, Florian; Schnick, Wolfgang; Juestel, Thomas; Schmidt, Peter

2005-07-01

The development and demonstration of a highly efficient warm-white all-nitride phosphor-converted light emitting diode (pc-LED) is presented utilizing a GaN based quantum well blue LED and two novel nitrogen containing luminescent materials, both of which are doped with Eu2+. For color conversion of the primary blue the nitridosilicates M2Si5N8 (orange-red) and MSi2O2N2 (yellow-green), with M = alkaline earth, were employed, thus achieving a high luminous efficiency (25 lumen/W at 1 W input), excellent color quality (correlated color temperature CCT = 3200 K, general color rendering index Ra > 90) and the highest proven color stability of any pc-LED obtained so far. Thus, these novel all-nitride LEDs are superior to both incandescent and fluorescent lamps and may therefore become the next generation of general lighting sources.

Gas turbine topping combustor

DOEpatents

Beer, Janos; Dowdy, Thomas E.; Bachovchin, Dennis M.

1997-01-01

A combustor for burning a mixture of fuel and air in a rich combustion zone, in which the fuel bound nitrogen in converted to molecular nitrogen. The fuel rich combustion is followed by lean combustion. The products of combustion from the lean combustion are rapidly quenched so as to convert the fuel bound nitrogen to molecular nitrogen without forming NOx. The combustor has an air radial swirler that directs the air radially inward while swirling it in the circumferential direction and a radial fuel swirler that directs the fuel radially outward while swirling it in the same circumferential direction, thereby promoting vigorous mixing of the fuel and air. The air inlet has a variable flow area that is responsive to variations in the heating value of the fuel, which may be a coal-derived fuel gas. A diverging passage in the combustor in front of a bluff body causes the fuel/air mixture to recirculate with the rich combustion zone.

Some new conceptions in the approach to harnessing tidal energy

NASA Astrophysics Data System (ADS)

Gorlov, A. M.

A method of converting ocean tide energy into compressed air energy for subsequent conversion to electrical and other forms of industrial energy is presented. The tidal energy is converted to compressed air energy by means of specialized chambers which are put on the ocean bed. Ocean water from the dammed region passes through the chamber where it works as a natural piston compressing air in the upper part of the closure. The compressed air can be expanded through high speed compact gas turbines or any type of reciprocating engine. The flexible reinforced plastic barrier should be substantially cheaper than a conventional rigid dam and can be designed so that by means of special floats it becomes a self-supported and self-regulated weightless structural system which can dam a large shallow space of ocean without having to be connected to special bays.

Kickdown control for a motor vehicle automatic transmission with two stage kickdown

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higashi, H.; Waki, K.; Fukuiri, M.

This patent describes a vehicle automatic transmission. This transmission consists of a hydraulic torque converter, a transmission gear mechanism connected with the torque converter and has at least three gear stages of different gear ratios for foward drive, friction for selecting one of the gear stages. A kick down control which consists of a first shift down circuit for controlling the friction so that the transmission gear mechanism is shifted down from a high gear stage to a lower gear stage. A kick down solenoid is provided in the first shift down circuit for controlling the first shift down circuitmore » and a kick down switch is adapted to be actuated by an engine control member. When the engine control member is moved substantially to a full power position to thereby control the kick down solenoid effects a shift down from a high gear stage to a lower gear stage.« less

A four-port vertical-coupling optical interface based on two-dimensional grating coupler

NASA Astrophysics Data System (ADS)

Zhang, Zan; Zhang, Zanyun; Huang, Beiju; Cheng, Chuantong; Gao, Tianxi; Hu, Xiaochuan; Zhang, Lin; Chen, Hongda

2016-10-01

In this work, a fiber-to-chip optical interface with four output ports is proposed. External lights irradiate vertically from single mode fiber to the center of optical interface can be coupled into silicon photonic chips and split into four siliconon- insulator (SOI) waveguides. If the light is circular polarized, the power of light will be equally split into four ports. Meanwhile, all lights travel in the four channel will be converted into TE polarization. The optical interface is based on a two-dimensional grating coupler with carefully designed duty cycle and period. Simulation results show that the coupling efficiency of each port can reach 11.6% so that the total coupling efficiency of the interface is 46.4%. And Lights coupled into four waveguides are all converted into TE polarization. Further, the optical interface has a simple grating structure allowing for easy fabrication.

Bacterial species involved in the conversion of dietary flavonoids in the human gut.

PubMed

Braune, Annett; Blaut, Michael

2016-05-03

The gut microbiota plays a crucial role in the conversion of dietary flavonoids and thereby affects their health-promoting effects in the human host. The identification of the bacteria involved in intestinal flavonoid conversion has gained increasing interest. This review summarizes available information on the so far identified human intestinal flavonoid-converting bacterial species and strains as well as their enzymes catalyzing the underlying reactions. The majority of described species involved in flavonoid transformation are capable of carrying out the O-deglycosylation of flavonoids. Other bacteria cleave the less common flavonoid-C-glucosides and/or further degrade the aglycones of flavonols, flavanonols, flavones, flavanones, dihydrochalcones, isoflavones and monomeric flavan-3-ols. To increase the currently limited knowledge in this field, identification of flavonoid-converting bacteria should be continued using culture-dependent screening or isolation procedures and molecular approaches based on sequence information of the involved enzymes.

An experimental investigation of performance of diesel to CNG engine

NASA Astrophysics Data System (ADS)

Misra, Sheelam; Gupta, Ayush; Garg, Ashutosh

2018-05-01

Over the past few decades, diesel engines are widely used in automobiles which is responsible for hazardous increase in pollution. Around the world, many countries are trying to reduce it by replacing diesel with CNG as a fuel which is more economical and leads to pollution free environment. Engineers came up with an idea to convert diesel engine to CNG engine. This conversion is possible by doing some alteration of engine components and it also include adding some extra components to the system which includes spark plug, valves etc. and by decreasing the compression ratio of the engine. It is used worldwide today and many countries have many programs to convert older, polluting diesel vehicles to CNG enable vehicles so that they can run on clean, economical natural gas. This is, an excellent way to reduce fuel cost, reduce pollution, reduce noise with minimum possible capital costs.first, second, and third level headings.

Piezoelectric step-motion actuator

DOEpatents

Mentesana,; Charles, P [Leawood, KS

2006-10-10

A step-motion actuator using piezoelectric material to launch a flight mass which, in turn, actuates a drive pawl to progressively engage and drive a toothed wheel or rod to accomplish stepped motion. Thus, the piezoelectric material converts electrical energy into kinetic energy of the mass, and the drive pawl and toothed wheel or rod convert the kinetic energy of the mass into the desired rotary or linear stepped motion. A compression frame may be secured about the piezoelectric element and adapted to pre-compress the piezoelectric material so as to reduce tensile loads thereon. A return spring may be used to return the mass to its resting position against the compression frame or piezoelectric material following launch. Alternative embodiment are possible, including an alternative first embodiment wherein two masses are launched in substantially different directions, and an alternative second embodiment wherein the mass is eliminated in favor of the piezoelectric material launching itself.

Explosive plane-wave lens

DOEpatents

Marsh, S.P.

1987-03-12

An explosive plane-wave air lens which enables a spherical wave form to be converted to a planar wave without the need to specially machine or shape explosive materials is described. A disc-shaped impactor having a greater thickness at its center than around its periphery is used to convert the spherical wave into a plane wave. When the wave reaches the impactor, the center of the impactor moves first because the spherical wave reaches the center of the impactor first. The wave strikes the impactor later in time as one moves radially along the impactor. Because the impactor is thinner as one moves radially outward, the velocity of the impactor is greater at the periphery than at the center. An acceptor explosive is positioned so that the impactor strikes the acceptor simultaneously. Consequently, a plane detonation wave is propagated through the acceptor explosive. 3 figs., 3 tabs.

Electrochemical separation and concentration of sulfur containing gases from gas mixtures

DOEpatents

Winnick, Jack

1981-01-01

A method of removing sulfur oxides of H.sub.2 S from high temperature gas mixtures (150.degree.-1000.degree. C.) is the subject of the present invention. An electrochemical cell is employed. The cell is provided with inert electrodes and an electrolyte which will provide anions compatible with the sulfur containing anions formed at the anode. The electrolyte is also selected to provide inert stable cations at the temperatures encountered. The gas mixture is passed by the cathode where the sulfur gases are converted to SO.sub.4.sup.= or, in the case of H.sub.2 S, to S.sup.=. The anions migrate to the anode where they are converted to a stable gaseous form at much greater concentration levels (>10X). Current flow may be effected by utilizing an external source of electrical energy or by passing a reducing gas such as hydrogen past the anode.

Specific pathologist responses for Standard for Exchange of Nonclinical Data (SEND).

PubMed

Watanabe, Atsushi; Kusuoka, Osamu; Sato, Norihiro; Nakazono, Osamu; Wasko, Michael; Potenta, Daniel; Nakae, Dai; Hatakeyama, Hirofumi; Iwata, Hijiri; Naota, Misaki; Anzai, Takayuki

2017-07-01

The Standard for Exchange of Nonclinical Data (SEND), introduced by the US Food and Drug Administration (FDA), is a scheme for the computerization, electronic application, and screening of preclinical data. Since its establishment, related organizations have been working together to implement SEND. However, it is difficult for individual pharmaceutical companies that often outsource to achieve complete compliance with SEND; hence, the cooperation of contract research organizations (CROs) and SEND Registered Solution Providers (RSPs) is indispensable. In SEND, most data, including those on pathology findings, are converted into controlled terminology (CT), but it is not a simple process to convert findings or levels of severity in the field of pathology, which is a descriptive science. The authors have successfully completed an FDA trial submission for a toxicology test conducted at a CRO and in doing so acquired important knowledge. This article presents a clear picture of such important knowledge from a pathologist's viewpoint.

Specific pathologist responses for Standard for Exchange of Nonclinical Data (SEND)

PubMed Central

Watanabe, Atsushi; Kusuoka, Osamu; Sato, Norihiro; Nakazono, Osamu; Wasko, Michael; Potenta, Daniel; Nakae, Dai; Hatakeyama, Hirofumi; Iwata, Hijiri; Naota, Misaki; Anzai, Takayuki

2017-01-01

The Standard for Exchange of Nonclinical Data (SEND), introduced by the US Food and Drug Administration (FDA), is a scheme for the computerization, electronic application, and screening of preclinical data. Since its establishment, related organizations have been working together to implement SEND. However, it is difficult for individual pharmaceutical companies that often outsource to achieve complete compliance with SEND; hence, the cooperation of contract research organizations (CROs) and SEND Registered Solution Providers (RSPs) is indispensable. In SEND, most data, including those on pathology findings, are converted into controlled terminology (CT), but it is not a simple process to convert findings or levels of severity in the field of pathology, which is a descriptive science. The authors have successfully completed an FDA trial submission for a toxicology test conducted at a CRO and in doing so acquired important knowledge. This article presents a clear picture of such important knowledge from a pathologist’s viewpoint. PMID:28798527

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chinthavali, Madhu Sudhan; Campbell, Steven L; Tolbert, Leon M

So far, vehicular power electronics integration is limited to the integration of on-board battery chargers (OBC) into the traction drive system and sometimes to the accessory dc/dc converters in plug-in electric vehicles (PEV). These integration approaches do not provide isolation from the grid although it is an important feature that is required for user interface systems that have grid connections. This is therefore a major limitation that needs to be addressed along with the integrated functionality. Furthermore, there is no previous study that proposes the integration of wireless charger with the other on-board components. This study features a unique waymore » of combining the wired and wireless charging functionalities with vehicle side boost converter integration and maintaining the isolation to provide the best solution to the plug-in electric vehicle users. The new topology is additionally compared with commercially available OBC systems from manufacturers.« less

Multiplying and detecting propagating microwave photons using inelastic Cooper-pair tunneling

NASA Astrophysics Data System (ADS)

Leppäkangas, Juha; Marthaler, Michael; Hazra, Dibyendu; Jebari, Salha; Albert, Romain; Blanchet, Florian; Johansson, Göran; Hofheinz, Max

2018-01-01

The interaction between propagating microwave fields and Cooper-pair tunneling across a DC-voltage-biased Josephson junction can be highly nonlinear. We show theoretically that this nonlinearity can be used to convert an incoming single microwave photon into an outgoing n -photon Fock state in a different mode. In this process, the electrostatic energy released in a Cooper-pair tunneling event is transferred to the outgoing Fock state, providing energy gain. The created multiphoton Fock state is frequency entangled and highly bunched. The conversion can be made reflectionless (impedance matched) so that all incoming photons are converted to n -photon states. With realistic parameters, multiplication ratios n >2 can be reached. By two consecutive multiplications, the outgoing Fock-state number can get sufficiently large to accurately discriminate it from vacuum with linear postamplification and power measurement. Therefore, this amplification scheme can be used as a single-photon detector without dead time.

Knowledge, Autonomy and Maturity: Developmental and Educational Concerns as Rhetorical Resources in Adolescents' Discussions regarding the Age of Electoral Majority in England

ERIC Educational Resources Information Center

Gibson, Stephen; Hamilton, Lorna

2013-01-01

Recent debates concerning the age of electoral majority in the UK have focused on the levels of knowledge and maturity of young people. However, little research has explored the ways in which adolescents orient to these concerns themselves. In this article, we present analyses from a qualitative interview investigation in Northern England, and…

Le "tournoi des deux nations" ou une election legislative en France (The "Tournament of Two Nations" or a Legislative Election in France)

ERIC Educational Resources Information Center

Pucheu, Rene; And Others

1978-01-01

A presentation of the French electoral process in the form of a drama. The acts are: the rules of the game, the electoral laws; a short analysis of the "plot," the campaign; and an imaginary account of a campaign. The intention was more methodological than informative. (Text is in French.) (AMH)

A Nonlinearity Minimization-Oriented Resource-Saving Time-to-Digital Converter Implemented in a 28 nm Xilinx FPGA

NASA Astrophysics Data System (ADS)

Wang, Yonggang; Liu, Chong

2015-10-01

Because large nonlinearity errors exist in the current tapped-delay line (TDL) style field programmable gate array (FPGA)-based time-to-digital converters (TDC), bin-by-bin calibration techniques have to be resorted for gaining a high measurement resolution. If the TDL in selected FPGAs is significantly affected by changes in ambient temperature, the bin-by-bin calibration table has to be updated as frequently as possible. The on-line calibration and calibration table updating increase the TDC design complexity and limit the system performance to some extent. This paper proposes a method to minimize the nonlinearity errors of TDC bins, so that the bin-by-bin calibration may not be needed while maintaining a reasonably high time resolution. The method is a two pass approach: By a bin realignment, the large number of wasted zero-width bins in the original TDL is reused and the granularity of the bins is improved; by a bin decimation, the bin size and its uniformity is traded-off, and the time interpolation by the delay line turns more precise so that the bin-by-bin calibration is not necessary. Using Xilinx 28 nm FPGAs, in which the TDL property is not very sensitive to ambient temperature, the proposed TDC achieves approximately 15 ps root-mean-square (RMS) time resolution by dual-channel measurements of time-intervals over the range of operating temperature. Because of removing the calibration and less logic resources required for the data post-processing, the method has bigger multi-channel capability.

Two stage kickdown control system for a motor vehicle automatic transmission

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higashi, H.; Waki, K.; Fukuiri, M.

This patent describes a vehicle automatic transmission including a hydraulic torque converter and a transmission gear mechanism connected with the torque converter and having at least three gear stages of different gear ratios for forward drive. A principal feature of this system as described is a friction means for selecting one of the gear stages as well as a kickdown control means consisting of the first shift down circuit means for control of the friction means so that the transmission gear mechanism is shifted downward. A solenoid kick down means within the modality of the first shift down circuit andmore » a kick down switch means actuated by an engine control member when it is moved to a full power position provides control of the kick down solenoid and the effecting of a down shift. The shift down control means is composed of a second shift down circuit means for controlling the friction means so shift down occurs. The shift down solenoid contained in the second shift down circuit means in conjunction with a shift down switch actuated by engine control member movement to a position spaced a predetermined distance from the full power position control the shift down solenoid to effect a shift down. Thus this mechanism is actuated earlier than the kickdown switch means when the engine control member is moved toward the full power position. A time delay means from the time of actuation of the shift down switch means and controlling kickdown switch activation is also described.« less

A Cryogenic Dc-Dc Power Converter for a 100 kW Synchronous HTS Generator at Liquid Nitrogen Temperatures

NASA Astrophysics Data System (ADS)

Bailey, Wendell; Wen, Hauming; Yang, Yifeng; Forsyth, Andrew; Jia, Chungjiang

A dc-dc converter has been developed for retrofitting inside the vacuum space of the HTS rotor of a synchronous generator. The heavy copper sections of the current leads used for energising the HTS field winding were replaced by cryogenic power electronics; consisting of the converter and a rotor control unit. The converter board was designed using an H-bridge configuration with two 5A rated wires connecting the cryogenic boards to the stator control board located on the outside of the generator and drawing power from a (5A, 50 V) dc power source. The robustness of converter board was well demonstrated when it was powered up from a cold start at 82K. When charging the field winding with moderate currents (30A), the heat in-leak to the 'cold' rotor core was only 2W. It continued to function down to 74K, surviving several quenches. However, the quench protection function failed when injecting 75A into the field winding, resulting in the burn out of one of the DC-link capacitors. The magnitudes of the critical currents measured with the original current leads were compared to the quench currents, which was defined as the current which triggered quench protection protocol. The difference between the two currents was rather large, (∼20A). However, additional measurements using a single HTS coil in liquid nitrogen found that this reduction should not be so dramatic and in the region of 4A. Our conclusions identified the converter's switching voltage and its operating frequency as two parameters, which could have contributed to lowering the quench current. Magnetic fields and eddy currents are expected to be more prominent the field winding and its impact on the converter also need further investigation.

A thermodynamic-like characterization of Colombia’s presidential elections in 2010, and a comparison with other Latin American countries

NASA Astrophysics Data System (ADS)

Campos, Diógenes

2011-05-01

A thermodynamic-like characterization of Colombia’s presidential election is presented. We assume that the electoral system consists of citizens embedded in a political environment, and that this environment can be considered as an information bath characterized by the entropic parameter q ( q∈[0,∞]). First, for q=1, the electoral outcomes of 2010 are translated into a set of probabilities (relative frequencies of the events) P={P1,P2,…,PN}, with N possible independent results. Then, for 0≤q<∞, the electoral system is characterized by using the thermodynamic-like method for probabilistic systems proposed in a previous article. Some general considerations of the macro-description of a probabilistic system and a comparison of presidential elections in five countries are also included.

Chile: Political and Economic Conditions and U.S. Relations

DTIC Science & Technology

2010-02-18

electoral democracy, which endured until 1973. During much of this period, Chile was governed by presidents who pursued import-substitution...the armed forces and other bodies. 6 Peter M. Siavelis, “ Electoral System, Coalitional Disintegration, and the Future of Chile’s Concertación...Course in Democracy,” Washington Post , November 25, 2006. 16 “Chile: Pinochet-era Education Law Finally Replaced,” Latin News Weekly Report, August 20

Lesson Plan on Comparative Political Systems: Compare and Contrast the Presidential Election System of the USA to the Parliamentary Election System of Hungary.

ERIC Educational Resources Information Center

O'Connell, Daniel W.

This lesson describes the current government of Hungary and its underlying political and electoral systems. The lesson is structured with: (1) background on the parliamentary model of government, political parties, and Hungary's unique electoral system; (2) a summary of the six major political parties in Hungary and voter information for the 1990…

Tally of the 1824 Electoral College Vote. The Constitution Community: Revolution and the New Nation (1754-1820s).

ERIC Educational Resources Information Center

Greene, Mary Frances

This lesson focuses on the role of the Electoral College in the election of the President and Vice-President as specified in the U.S. Constitution in Article II, Section 1, Clauses 2 and 4, and the Twelfth Amendment. The lesson correlates to the National History Standards and the National Standards for Civics and Government. The tally of the 1824…

Distribution of Votes and a Model of Political Opinion Formation for Majority Elections

NASA Astrophysics Data System (ADS)

Prenga, Dode; Ifti, Margarita

We study the behavior of the number of votes cast for different electoral subjects in majority elections, and in particular, the Albanian elections of the last 10 years, as well as the British, Russian, and Canadian elections. We report the frequency of obtaining a certain percentage (fraction) of votes versus this fraction for the parliamentary elections. In the distribution of votes cast in majority elections we identify two regimes. In the low percentiles we see a power law distribution, with exponent about -1.7. In the power law regime we find over 80% of the data points, while they relate to 20% of the votes cast. Votes of the small electoral subjects are found in this regime. The other regime includes percentiles above 20%, and has Gaussian distribution. It corresponds to large electoral subjects. A similar pattern is observed in other first past the post (FPP) elections, such as British and Canadian, but here the Gaussian is reduced to an exponential. Finally we show that this distribution can not be reproduced by a modified "word of mouth" model of opinion formation. This behavior can be reproduced by a model that comprises different number of zealots, as well as different campaign strengths for different electoral subjects, in presence of preferential attachment of voters to candidates.

Results on three predictions for July 2012 federal elections in Mexico based on past regularities.

PubMed

Hernández-Saldaña, H

2013-01-01

The Presidential Election in Mexico of July 2012 has been the third time that PREP, Previous Electoral Results Program works. PREP gives voting outcomes based in electoral certificates of each polling station that arrive to capture centers. In previous ones, some statistical regularities had been observed, three of them were selected to make predictions and were published in arXiv:1207.0078 [physics.soc-ph]. Using the database made public in July 2012, two of the predictions were completely fulfilled, while, the third one was measured and confirmed using the database obtained upon request to the electoral authorities. The first two predictions confirmed by actual measures are: (ii) The Partido Revolucionario Institucional, PRI, is a sprinter and has a better performance in polling stations arriving late to capture centers during the process. (iii) Distribution of vote of this party is well described by a smooth function named a Daisy model. A Gamma distribution, but compatible with a Daisy model, fits the distribution as well. The third prediction confirms that errare humanum est, since the error distributions of all the self-consistency variables appeared as a central power law with lateral lobes as in 2000 and 2006 electoral processes. The three measured regularities appeared no matter the political environment.

Results on Three Predictions for July 2012 Federal Elections in Mexico Based on Past Regularities

PubMed Central

Hernández-Saldaña, H.

2013-01-01

The Presidential Election in Mexico of July 2012 has been the third time that PREP, Previous Electoral Results Program works. PREP gives voting outcomes based in electoral certificates of each polling station that arrive to capture centers. In previous ones, some statistical regularities had been observed, three of them were selected to make predictions and were published in arXiv:1207.0078 [physics.soc-ph]. Using the database made public in July 2012, two of the predictions were completely fulfilled, while, the third one was measured and confirmed using the database obtained upon request to the electoral authorities. The first two predictions confirmed by actual measures are: (ii) The Partido Revolucionario Institucional, PRI, is a sprinter and has a better performance in polling stations arriving late to capture centers during the process. (iii) Distribution of vote of this party is well described by a smooth function named a Daisy model. A Gamma distribution, but compatible with a Daisy model, fits the distribution as well. The third prediction confirms that errare humanum est, since the error distributions of all the self-consistency variables appeared as a central power law with lateral lobes as in 2000 and 2006 electoral processes. The three measured regularities appeared no matter the political environment. PMID:24386103

A Raman and Infrared Spectroscopic Study of Anglesite at High Pressures

NASA Astrophysics Data System (ADS)

Sawchuk, K. L. S.; Vennari, C.; O'Bannon, E. F., III; Williams, Q.

2016-12-01

Raman and infrared spectra of the barite-structured lead sulfate, anglesite (PbSO4), were collected to 40 GPa and 300 K. Our particular interest in this compound is oriented towards determining what post-barite structures sulfates in the deep earth sulfur cycle might ultimately convert to at high pressures. Additionally, the study of ABX4 materials has applications to materials science that include their usage as scintillation detectors, and PbSO4 has been demonstrated to have non-linear optical properties. Measurements were made of the internal modes of the SO4 group that lie between 400 and 1200 cm-1 and lattice vibrations that occur between 50 and 250 cm-1. In accord with previous Raman work of Lee et al. (WJCMP, 2012), two phase transitions initiate at 13 and 23 GPa which are reversible on decompression. The 13 GPa transition is subtle and involves splitting of a few modes, particularly the SO4 tetragonal stretching and bending-derived Raman and associated infrared modes. This transition likely goes to a structure with a greater degree of Davydov splitting between corresponding Raman- and infrared-active vibrations, which may indicate a greater distortion of the SO4 tetrahedra. The transition at 23 GPa is a major, sluggish, transition that causes splitting and/or shifting in all observed Raman and infrared modes. These new peaks are lower in frequency and become the sole spectral features by 42 GPa suggesting a higher symmetry structure than previously inferred. It appears that this transition involves a coexistence of phases until the transition is ultimately complete around 42 GPa. Based on the structural systematics of ABX4 phases and factor group analysis, it is likely the structure goes to the monazite structure at high pressures, but that this transition required marked overpressurization to occur at 300K. The accessing of this monazite-like phase is in general accord with systematics of high-pressure transitions in ABX4 phases, and indicates that monazite-structured polymorphs may be anticipated within subducted high-pressure sulfates within Earth's mantle.

The Many Problems with Geoengineering Using Stratospheric Aerosols

NASA Astrophysics Data System (ADS)

Robock, Alan

2009-05-01

In response to the global warming problem, there has been a recent renewed call for geoengineering ``solutions'' involving injecting particles into the stratosphere or blocking sunlight with satellites between the Sun and Earth. While volcanic eruptions have been suggested as innocuous examples of stratospheric aerosols cooling the planet, the volcano analog actually argues against geoengineering because of ozone depletion and regional hydrologic and temperature responses. In this talk, I consider the suggestion to create an artificial stratospheric aerosol layer. No systems to conduct geoengineering now exist, but a comparison of different proposed stratospheric injection schemes, airplanes, balloons, artillery, and a space elevator, shows that using airplanes would not be that expensive. We simulated the climate response to both tropical and Arctic stratospheric injection of sulfate aerosol precursors using a comprehensive atmosphere-ocean general circulation model, the National Aeronautics and Space Administration Goddard Institute for Space Studies ModelE. We simulated the injection of SO2 and the model converts it to sulfate aerosols, transports them and removes them through dry and wet deposition, and calculates the climate response to the radiative forcing from the aerosols. We conducted simulations of future climate with the Intergovernmental Panel on Climate Change A1B business-as-usual scenario both with and without geoengineering, and compare the results. We found that if there were a way to continuously inject SO2 into the lower stratosphere, it would produce global cooling. Acid deposition from the sulfate would not be enough to disturb most ecosystems. Tropical SO2 injection would produce sustained cooling over most of the world, with more cooling over continents. Arctic SO2 injection would not just cool the Arctic. But both tropical and Arctic SO2 injection would disrupt the Asian and African summer monsoons, reducing precipitation to the food supply for billions of people. These regional climate anomalies are but one of many reasons why geoengineering may be a bad idea. I also discuss 19 other reasons. Global efforts to mitigate anthropogenic emissions and to adapt to climate change are a much better way to channel our resources to address anthropogenic global warming.

Iterative current mode per pixel ADC for 3D SoftChip implementation in CMOS

NASA Astrophysics Data System (ADS)

Lachowicz, Stefan W.; Rassau, Alexander; Lee, Seung-Minh; Eshraghian, Kamran; Lee, Mike M.

2003-04-01

Mobile multimedia communication has rapidly become a significant area of research and development constantly challenging boundaries on a variety of technological fronts. The processing requirements for the capture, conversion, compression, decompression, enhancement, display, etc. of increasingly higher quality multimedia content places heavy demands even on current ULSI (ultra large scale integration) systems, particularly for mobile applications where area and power are primary considerations. The ADC presented in this paper is designed for a vertically integrated (3D) system comprising two distinct layers bonded together using Indium bump technology. The top layer is a CMOS imaging array containing analogue-to-digital converters, and a buffer memory. The bottom layer takes the form of a configurable array processor (CAP), a highly parallel array of soft programmable processors capable of carrying out complex processing tasks directly on data stored in the top plane. This paper presents a ADC scheme for the image capture plane. The analogue photocurrent or sampled voltage is transferred to the ADC via a column or a column/row bus. In the proposed system, an array of analogue-to-digital converters is distributed, so that a one-bit cell is associated with one sensor. The analogue-to-digital converters are algorithmic current-mode converters. Eight such cells are cascaded to form an 8-bit converter. Additionally, each photo-sensor is equipped with a current memory cell, and multiple conversions are performed with scaled values of the photocurrent for colour processing.

Opinion control in complex networks

NASA Astrophysics Data System (ADS)

Masuda, Naoki

2015-03-01

In many political elections, the electorate appears to be a composite of partisan and independent voters. Given that partisans are not likely to convert to a different party, an important goal for a political party could be to mobilize independent voters toward the party with the help of strong leadership, mass media, partisans, and the effects of peer-to-peer influence. Based on the exact solution of classical voter model dynamics in the presence of perfectly partisan voters (i.e., zealots), we propose a computational method that uses pinning control strategy to maximize the share of a party in a social network of independent voters. The party, corresponding to the controller or zealots, optimizes the nodes to be controlled given the information about the connectivity of independent voters and the set of nodes that the opposing party controls. We show that controlling hubs is generally a good strategy, but the optimized strategy is even better. The superiority of the optimized strategy is particularly eminent when the independent voters are connected as directed (rather than undirected) networks.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, George

VICE 2.0 is the second generation of the VICE financial model developed by the National Renewable Energy Laboratory for fleet managers to assess the financial soundness of converting their fleets to run on CNG. VICE 2.0 uses a number of variables for infrastructure and vehicles to estimate the business case for decision-makers when considering CNG as a vehicle fuel. Enhancements in version 2.0 include the ability to select the project type (vehicles and infrastructure or vehicle acquisitions only), and to decouple vehicle acquisition from the infrastructure investment, so the two investments may be made independently. Outputs now include graphical presentationsmore » of investment cash flow, payback period (simple and discounted), petroleum displacement (annual and cumulative), and annual greenhouse gas reductions. Also, the Vehicle Data are now built around several common conventionally fueled (gasoline and diesel) fleet vehicles. Descriptions of the various model sections and available inputs follow. Each description includes default values for the base-case business model, which was created so economic sensitivities can be investigated by altering various project parameters one at a time.« less

Extracellular synthesis and characterization of nickel oxide nanoparticles from Microbacterium sp. MRS-1 towards bioremediation of nickel electroplating industrial effluent.

PubMed

Sathyavathi, S; Manjula, A; Rajendhran, J; Gunasekaran, P

2014-08-01

In the present study, a nickel resistant bacterium MRS-1 was isolated from nickel electroplating industrial effluent, capable of converting soluble NiSO4 into insoluble NiO nanoparticles and identified as Microbacterium sp. The formation of NiO nanoparticles in the form of pale green powder was observed on the bottom of the flask upon prolonged incubation of liquid nutrient medium containing high concentration of 2000ppm NiSO4. The properties of the produced NiO nanoparticles were characterized. NiO nanoparticles exhibited a maximum absorbance at 400nm. The NiO nanoparticles were 100-500nm in size with unique flower like structure. The elemental composition of the NiO nanoparticles was 44:39. The cells of MRS-1 were utilized for the treatment of nickel electroplating industrial effluent and showed nickel removal efficiency of 95%. Application of Microbacterium sp. MRS-1 would be a potential bacterium for bioremediation of nickel electroplating industrial waste water and simultaneous synthesis of NiO nanoparticles. Copyright © 2014 Elsevier Ltd. All rights reserved.

Design and experimental evidence of a flat graded-index photonic crystal lens

NASA Astrophysics Data System (ADS)

Gaufillet, F.; Akmansoy, É.

2013-08-01

We report on the design and the experimental evidence of a flat graded index photonic crystal lens. The gradient has been designed so that the flat slab focuses a plane wave and so that it converts the wave issued from a point source into a plane wave. This graded-index photonic crystal lens operates as a convex lens. The gradient of index results from varying the filling factor of the photonic crystal in the direction perpendicular to that of the propagation of the electromagnetic field. The shape of the gradient of index has been designed by engineering the iso-frequency curves of the photonic crystal. As only a few layers were necessary and as graded photonic crystals may be fabricated by a variety of processes, this shows the ability of graded photonic crystals to efficiently apply for various photonic devices, from microwave range to the optical domain. 42.70.Qs Photonic bandgap materials, 78.67.Pt Optical properties of photonic structures, 41.20.Jb Electromagnetic wave propagation; radiowave propagation 84.40.Ba Antennas.

Tangeretin-loaded protein nanoparticles fabricated from zein/β-lactoglobulin: preparation, characterization, and functional performance.

PubMed

Chen, Jingjing; Zheng, Jinkai; McClements, David Julian; Xiao, Hang

2014-09-01

The aim of this study was to design a colloidal delivery system to encapsulate poor water-soluble bioactive flavonoid tangeretin so that it could be utilized in various food products as functional ingredient. Tangeretin-loaded protein nanoparticles were produced by mixing an organic phase containing zein and tangeretin with an aqueous phase containing β-lactoglobulin and then converted into powder by freeze-drying. This powder formed a colloidal suspension when dispersed in water that is relatively stable to particle aggregation and sedimentation. The influence of temperature, ionic strength, and pH on the stability of the protein nanoparticles was tested. Extensive particle aggregation occurred at high ionic strength (>100mM) and intermediate pH (4.5-5.5) due to reduced electrostatic repulsion. Extensive aggregation also occurred at temperatures exceeding 60 °C, which was presumably due to increased hydrophobic attraction. Overall, this study shows that protein-based nanoparticles can be used to encapsulate bioactive tangeretin so that it can be readily dispersed in compatible food products. Copyright © 2014 Elsevier Ltd. All rights reserved.

Why Antidiabetic Vanadium Complexes are Not in the Pipeline of "Big Pharma" Drug Research? A Critical Review.

PubMed

Scior, Thomas; Guevara-Garcia, Jose Antonio; Do, Quoc-Tuan; Bernard, Philippe; Laufer, Stefan

2016-01-01

Public academic research sites, private institutions as well as small companies have made substantial contributions to the ongoing development of antidiabetic vanadium compounds. But why is this endeavor not echoed by the globally operating pharmaceutical companies, also known as "Big Pharma"? Intriguingly, today's clinical practice is in great need to improve or replace insulin treatment against Diabetes Mellitus (DM). Insulin is the mainstay therapeutically and economically. So, why do those companies develop potential antidiabetic drug candidates without vanadium (vanadium- free)? We gathered information about physicochemical and pharmacological properties of known vanadium-containing antidiabetic compounds from the specialized literature, and converted the data into explanations (arguments, the "pros and cons") about the underpinnings of antidiabetic vanadium. Some discoveries were embedded in chronological order while seminal reviews of the last decade about the Medicinal chemistry of vanadium and its history were also listed for further understanding. In particular, the concepts of so-called "noncomplexed or free" vanadium species (i.e. inorganic oxido-coordinated species) and "biogenic speciation" of antidiabetic vanadium complexes were found critical and subsequently documented in more details to answer the question.

Optically- and thermally-stimulated luminescences of Ce-doped SiO2 glasses prepared by spark plasma sintering

NASA Astrophysics Data System (ADS)

Okada, Go; Kasap, Safa; Yanagida, Takayuki

2016-11-01

Rare-earth doped phosphors have been used in many applications including radiation measurements. In the latter applications, the radiation photons are converted to light so that we can indirectly detect the radiation using a conventional photodetector. In this work, we have prepared and characterized a Ce-doped SiO2 glass for dosimeter applications. Unlike conventional techniques such as sol-gel synthesis, the sample was prepared by spark plasma sintering. Although the PL emission seems to be only from the Ce3+ ions in the structure, due to the X-ray induced luminescence, we have also observed optically-stimulated luminescence (OSL), and thermally-stimulated luminescence (TSL), owing to a pair of silylenes and a set of dioxasilirane and silylene in addition to Ce3+. We have measured the detector response vs irradiation dose for both the OSL and TSL. The detector response in both cases is linear over the dose range from at least 1 mGy to 2 Gy. Particularly, the sensitivity of TSL is so high that it should be considered to be a good candidate for practical applications.

Silencing Onion Lachrymatory Factor Synthase Causes a Significant Change in the Sulfur Secondary Metabolite Profile1[W][OA

PubMed Central

Eady, Colin C.; Kamoi, Takahiro; Kato, Masahiro; Porter, Noel G.; Davis, Sheree; Shaw, Martin; Kamoi, Akiko; Imai, Shinsuke

2008-01-01

Through a single genetic transformation in onion (Allium cepa), a crop recalcitrant to genetic transformation, we suppressed the lachrymatory factor synthase gene using RNA interference silencing in six plants. This reduced lachrymatory synthase activity by up to 1,544-fold, so that when wounded the onions produced significantly reduced levels of tear-inducing lachrymatory factor. We then confirmed, through a novel colorimetric assay, that this silencing had shifted the trans-S-1-propenyl-l-cysteine sulfoxide breakdown pathway so that more 1-propenyl sulfenic acid was converted into di-1-propenyl thiosulfinate. A consequence of this raised thiosulfinate level was a marked increase in the downstream production of a nonenzymatically produced zwiebelane isomer and other volatile sulfur compounds, di-1-propenyl disulfide and 2-mercapto-3,4-dimethyl-2,3-dihydrothiophene, which had previously been reported in trace amounts or had not been detected in onion. The consequences of this dramatic simultaneous down- and up-regulation of secondary sulfur products on the health and flavor attributes of the onion are discussed. PMID:18583530

Acid attack on hydrated cement — Effect of mineral acids on the degradation process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gutberlet, T.; Hilbig, H.; Beddoe, R.E., E-mail: robin.beddoe@tum.de

During acid attack on concrete structural components, a degraded layer develops whose properties as a protective barrier are decisive for durability. {sup 29}Si NMR spectroscopy and {sup 27}Al NMR spectroscopy were used with XRD to investigate the degraded layer on hardened cement paste exposed to HCl and H{sub 2}SO{sub 4}. The layer comprises an amorphous silica gel with framework silicates, geminate and single silanol groups in which Si is substituted by Al. Amorphous Al(OH){sub 3} and Fe(OH){sub 3} are present. The gel forms by polycondensation and cross-linking of C-A-S-H chains at AlO{sub 4} bridging tetrahedra. In the transition zone betweenmore » the degraded layer and the undamaged material, portlandite dissolves and Ca is removed from the C-A-S-H phases maintaining their polymer structure at first. With HCl, monosulphate in the transition zone is converted into Friedel's salt and ettringite. With H{sub 2}SO{sub 4}, gypsum precipitates near the degradation front reducing the thickness of the transition zone and the rate of degradation.« less

Sulfate Separation by Selective Crystallization with a Bis-iminoguanidinium Ligand.

PubMed

Seipp, Charles A; Williams, Neil J; Custelcean, Radu

2016-09-08

A simple and effective method for selective sulfate separation from aqueous solutions by crystallization with a bis-guanidinium ligand, 1,4-benzene-bis(iminoguanidinium) (BBIG), is demonstrated. The ligand is synthesized as the chloride salt (BBIG-Cl) by in situ imine condensation of terephthalaldehyde with aminoguanidinium chloride in water, followed by crystallization as the sulfate salt (BBIG-SO4). Alternatively, BBIG-Cl is synthesized ex situ in larger scale from ethanol. The sulfate separation ability of the BBIG ligand is demonstrated by selective and quantitative crystallization of sulfate from seawater. The ligand can be recycled by neutralization of BBIG-SO4 with aqueous NaOH and crystallization of the neutral bis-iminoguanidine, which can be converted back into BBIG-Cl with aqueous HCl and reused in another separation cycle. Finally, (35)S-labeled sulfate and β liquid scintillation counting are employed for monitoring the sulfate concentration in solution. Overall, this protocol will instruct the user in the necessary skills to synthesize a ligand, employ it in the selective crystallization of sulfate from aqueous solutions, and quantify the separation efficiency.

Sulfate Separation by Selective Crystallization with a Bis-iminoguanidinium Ligand

DOE PAGES

Seipp, Charles A.; Williams, Neil J.; Custelcean, Radu

2016-01-01

One simple and effective method for selective sulfate separation from aqueous solutions by crystallization with a bis-guanidinium ligand, 1,4-benzene-bis(iminoguanidinium) (BBIG), is demonstrated. The ligand is synthesized as the chloride salt (BBIG-Cl) by in situ imine condensation of terephthalaldehyde with aminoguanidinium chloride in water, followed by crystallization as the sulfate salt (BBIG-SO4). Alternatively, BBIG-Cl is synthesized ex situ in larger scale from ethanol. Furthermore, the sulfate separation ability of the BBIG ligand is demonstrated by selective and quantitative crystallization of sulfate from seawater. These ligands can then be recycled by neutralization of BBIG-SO4 with aqueous NaOH and crystallization of the neutralmore » bis-iminoguanidine, which can be converted back into BBIG-Cl with aqueous HCl and reused in another separation cycle. Finally, 35S-labeled sulfate and β liquid scintillation counting are employed for monitoring the sulfate concentration in solution. Overall, this protocol will instruct the user in the necessary skills to synthesize a ligand, employ it in the selective crystallization of sulfate from aqueous solutions, and quantify the separation efficiency.« less

Silencing onion lachrymatory factor synthase causes a significant change in the sulfur secondary metabolite profile.

PubMed

Eady, Colin C; Kamoi, Takahiro; Kato, Masahiro; Porter, Noel G; Davis, Sheree; Shaw, Martin; Kamoi, Akiko; Imai, Shinsuke

2008-08-01

Through a single genetic transformation in onion (Allium cepa), a crop recalcitrant to genetic transformation, we suppressed the lachrymatory factor synthase gene using RNA interference silencing in six plants. This reduced lachrymatory synthase activity by up to 1,544-fold, so that when wounded the onions produced significantly reduced levels of tear-inducing lachrymatory factor. We then confirmed, through a novel colorimetric assay, that this silencing had shifted the trans-S-1-propenyl-l-cysteine sulfoxide breakdown pathway so that more 1-propenyl sulfenic acid was converted into di-1-propenyl thiosulfinate. A consequence of this raised thiosulfinate level was a marked increase in the downstream production of a nonenzymatically produced zwiebelane isomer and other volatile sulfur compounds, di-1-propenyl disulfide and 2-mercapto-3,4-dimethyl-2,3-dihydrothiophene, which had previously been reported in trace amounts or had not been detected in onion. The consequences of this dramatic simultaneous down- and up-regulation of secondary sulfur products on the health and flavor attributes of the onion are discussed.

Screening of novel bacteria for the 2,3-butanediol production.

PubMed

Kallbach, Malee; Horn, Sonja; Kuenz, Anja; Prüße, Ulf

2017-02-01

Biotechnologically produced 2,3-butanediol (2,3-BDO) is a potential starting material for industrial bulk chemicals such as butadiene or methyl ethyl ketone which are currently produced from fossil feedstocks. So far, the highest 2,3-BDO concentrations have been obtained with risk group 2 microorganisms. In this study, three risk group 1 microorganisms are presented that are so far unknown for an efficient production of 2,3-BDO. The strains Bacillus atrophaeus NRS-213, Bacillus mojavensis B-14698, and Bacillus vallismortis B-14891 were evaluated regarding their ability to produce high 2,3-BDO concentrations with a broad range of different carbon sources. A maximum 2,3-BDO concentration of 60.4 g/L was reached with the strain B. vallismortis B-14891 with an initial glucose concentration of 200 g/L within 55 h in a batch cultivation. Besides glucose, B. vallismortis B-14891 converts 14 different substrates that can be obtained from residual biomass sources to 2,3-BDO. Therefore B. vallismortis B-14891 is a promising candidate for the large-scale production of 2,3-BDO with low-cost substrates.

Simultaneous saccharification and fermentation (SSF) of Jatropha curcas shells: utilization of co-products from the biodiesel production process.

PubMed

Visser, Evan Michael; Oliveira Filho, Delly; Tótola, Marcos Rogério; Martins, Marcio Arêdes; Guimarães, Valéria Monteze

2012-06-01

Jatropha curcas has great potential as an oil crop for use in biodiesel applications, and the outer shell is rich in lignocellulose that may be converted to ethanol, giving rise to the concept of a biorefinery. In this study, two dilute pretreatments of 0.5% H(2)SO(4) and 1.0% NaOH were performed on Jatropha shells with subsequent simultaneous saccharification and fermentation (SSF) of the pretreated water-insoluble solids (WIS) to evaluate the effect of inhibitors in the pretreatment slurry. A cellulase loading of 15 FPU/g WIS, complimented with an excess of cellobiase (19.25 U/g), was used for SSF of either the washed WIS or the original slurry to determine the effect of inhibitors. Ethanol and glucose were monitored during SSF of 20 g of pretreated biomass. The unwashed slurry showed to have a positive effect on SSF efficiency for the NaOH-pretreated biomass. Maximum efficiencies of glucan conversion to ethanol in the WIS were 40.43% and 41.03% for the H(2)SO(4)- and NaOH-pretreated biomasses, respectively.

Coherent Addressing of Individual Neutral Atoms in a 3D Optical Lattice.

PubMed

Wang, Yang; Zhang, Xianli; Corcovilos, Theodore A; Kumar, Aishwarya; Weiss, David S

2015-07-24

We demonstrate arbitrary coherent addressing of individual neutral atoms in a 5×5×5 array formed by an optical lattice. Addressing is accomplished using rapidly reconfigurable crossed laser beams to selectively ac Stark shift target atoms, so that only target atoms are resonant with state-changing microwaves. The effect of these targeted single qubit gates on the quantum information stored in nontargeted atoms is smaller than 3×10^{-3} in state fidelity. This is an important step along the path of converting the scalability promise of neutral atoms into reality.

Visualization techniques for malware behavior analysis

NASA Astrophysics Data System (ADS)

Grégio, André R. A.; Santos, Rafael D. C.

2011-06-01

Malware spread via Internet is a great security threat, so studying their behavior is important to identify and classify them. Using SSDT hooking we can obtain malware behavior by running it in a controlled environment and capturing interactions with the target operating system regarding file, process, registry, network and mutex activities. This generates a chain of events that can be used to compare them with other known malware. In this paper we present a simple approach to convert malware behavior into activity graphs and show some visualization techniques that can be used to analyze malware behavior, individually or grouped.

Economic manufacturing of bulk metallic glass compositions by microalloying

DOEpatents

Liu, Chain T.

2003-05-13

A method of making a bulk metallic glass composition includes the steps of:a. providing a starting material suitable for making a bulk metallic glass composition, for example, BAM-11; b. adding at least one impurity-mitigating dopant, for example, Pb, Si, B, Sn, P, to the starting material to form a doped starting material; and c. converting the doped starting material to a bulk metallic glass composition so that the impurity-mitigating dopant reacts with impurities in the starting material to neutralize deleterious effects of the impurities on the formation of the bulk metallic glass composition.

Convex functions and some inequalities in terms of the Non-Newtonian Calculus

NASA Astrophysics Data System (ADS)

Unluyol, Erdal; Salas, Seren; Iscan, Imdat

2017-04-01

Differentiation and integration are basic operations of calculus and analysis. Indeed, they are many versions of the subtraction and addition operations on numbers, respectively. From 1967 till 1970 Michael Grossman and Robert Katz [1] gave definitions of a new kind of derivative and integral, converting the roles of subtraction and addition into division and multiplication, and thus establish a new calculus, called Non-Newtonian Calculus. So, in this paper, it is investigated to the convex functions and some inequalities in terms of Non-Newtonian Calculus. Then we compare with the Newtonian and Non-Newtonian Calculus.

Digital radiographic imaging: is the dental practice ready?

PubMed

Parks, Edwin T

2008-04-01

Digital radiographic imaging is slowly, but surely, replacing film-based imaging. It has many advantages over traditional imaging, but the technology also has some drawbacks. The author presents an overview of the types of digital image receptors available, image enhancement software and the range of costs for the new technology. PRACTICE IMPLICATIONS. The expenses associated with converting to digital radiographic imaging are considerable. The purpose of this article is to provide the clinician with an overview of digital radiographic imaging technology so that he or she can be an informed consumer when evaluating the numerous digital systems in the marketplace.

Underground gasification of coal

DOEpatents

Pasini, III, Joseph; Overbey, Jr., William K.; Komar, Charles A.

1976-01-20

There is disclosed a method for the gasification of coal in situ which comprises drilling at least one well or borehole from the earth's surface so that the well or borehole enters the coalbed or seam horizontally and intersects the coalbed in a direction normal to its major natural fracture system, initiating burning of the coal with the introduction of a combustion-supporting gas such as air to convert the coal in situ to a heating gas of relatively high calorific value and recovering the gas. In a further embodiment the recovered gas may be used to drive one or more generators for the production of electricity.

Cyclic process for producing methane from carbon monoxide with heat removal

DOEpatents

Frost, Albert C.; Yang, Chang-lee

1982-01-01

Carbon monoxide-containing gas streams are converted to methane by a cyclic, essentially two-step process in which said carbon monoxide is disproportionated to form carbon dioxide and active surface carbon deposited on the surface of a catalyst, and said carbon is reacted with steam to form product methane and by-product carbon dioxide. The exothermic heat of reaction generated in each step is effectively removed during each complete cycle so as to avoid a build up of heat from cycle-to-cycle, with particularly advantageous techniques being employed for fixed bed, tubular and fluidized bed reactor operations.

Cyclic process for producing methane in a tubular reactor with effective heat removal

DOEpatents

Frost, Albert C.; Yang, Chang-Lee

1986-01-01

Carbon monoxide-containing gas streams are converted to methane by a cyclic, essentially two-step process in which said carbon monoxide is disproportionated to form carbon dioxide and active surface carbon deposited on the surface of a catalyst, and said carbon is reacted with steam to form product methane and by-product carbon dioxide. The exothermic heat of reaction generated in each step is effectively removed during each complete cycle so as to avoid a build up of heat from cycle-to-cycle, with particularly advantageous techniques being employed for fixed bed, tubular and fluidized bed reactor operations.

Gas only nozzle

DOEpatents

Bechtel, William Theodore; Fitts, David Orus; DeLeonardo, Guy Wayne

2002-01-01

A diffusion flame nozzle gas tip is provided to convert a dual fuel nozzle to a gas only nozzle. The nozzle tip diverts compressor discharge air from the passage feeding the diffusion nozzle air swirl vanes to a region vacated by removal of the dual fuel components, so that the diverted compressor discharge air can flow to and through effusion holes in the end cap plate of the nozzle tip. In a preferred embodiment, the nozzle gas tip defines a cavity for receiving the compressor discharge air from a peripheral passage of the nozzle for flow through the effusion openings defined in the end cap plate.

Gammaretroviral Vectors: Biology, Technology and Application

PubMed Central

Maetzig, Tobias; Galla, Melanie; Baum, Christopher; Schambach, Axel

2011-01-01

Retroviruses are evolutionary optimized gene carriers that have naturally adapted to their hosts to efficiently deliver their nucleic acids into the target cell chromatin, thereby overcoming natural cellular barriers. Here we will review—starting with a deeper look into retroviral biology—how Murine Leukemia Virus (MLV), a simple gammaretrovirus, can be converted into an efficient vehicle of genetic therapeutics. Furthermore, we will describe how more rational vector backbones can be designed and how these so-called self-inactivating vectors can be pseudotyped and produced. Finally, we will provide an overview on existing clinical trials and how biosafety can be improved. PMID:21994751

Post-polymerization functionalization of polyolefins.

PubMed

Boaen, Nicole K; Hillmyer, Marc A

2005-03-01

Polyolefins are macromolecular alkanes and include the most familiar and most commercially produced plastic, polyethylene. The low cost of these materials combined with their diverse and desirable property profiles drive such large-scale production. One property that renders polyolefins so attractive is their resistance to harsh chemical environments. However, this attribute becomes a severe limitation when attempting to chemically convert these plastics into value-added materials. Functionalization of polymers is a useful methodology for the generation of new materials with wide ranging applications, and this tutorial review describes both new and established methods for the post-polymerization modification of polyolefins.

Gas only nozzle fuel tip

DOEpatents

Bechtel, William Theodore; Fitts, David Orus; DeLeonardo, Guy Wayne

2002-01-01

A diffusion flame nozzle gas tip is provided to convert a dual fuel nozzle to a gas only nozzle. The nozzle tip diverts compressor discharge air from the passage feeding the diffusion nozzle air swirl vanes to a region vacated by removal of the dual fuel components, so that the diverted compressor discharge air can flow to and through effusion holes in the end cap plate of the nozzle tip. In a preferred embodiment, the nozzle gas tip defines a cavity for receiving the compressor discharge air from a peripheral passage of the nozzle for flow through the effusion openings defined in the end cap plate.

Transactions of the All-Union Conference (2nd) on Charged Particle Accelerators, Moscow, 11-18 November 1970. Volume I,

DTIC Science & Technology

1980-07-18

of investigatiom. as it follows from Fig. 4b, the range of the firing angle of valves/gates in this case does not exceed 15 el. dog . The oscillograms...z80069213 PAGE ia Fig. 1. Porn of the pole pxece of thenmodel of magnetic system. 0 0 Zu 30 40 so 0 P Fig. 2. Design concept of magnetic system with...ang1a of control; c) the currsnt of valve converter. Key: (1). dog . Page 183. DOC 80069214 PAGE In ta unit of starting impulses/momenta/palses (BSI) ace

Group Sparse Optimization by Alternating Direction Method

DTIC Science & Technology

2012-11-22

to solving the following linear system: (β1G TG+ β2A TA)x = β1G T z −GTλ1 + β2AT b+ATλ2. (3.5) Note that GTG ∈ Rn×n is a diagonal matrix whose i-th...diagonal entry is the number of repetitions of xi in x̃. When the groups form an complete cover of the solution, the diagonal entries of GTG will be...positive, so GTG is invertible. In the next subsection, we will show that an incomplete cover case can be converted to a complete cover case by

RADIOACTIVE BATTERY

DOEpatents

Birden, J.H.; Jordan, K.C.

1959-11-17

A radioactive battery which includes a capsule containing the active material and a thermopile associated therewith is presented. The capsule is both a shield to stop the radiations and thereby make the battery safe to use, and an energy conventer. The intense radioactive decay taking place inside is converted to useful heat at the capsule surface. The heat is conducted to the hot thermojunctions of a thermopile. The cold junctions of the thermopile are thermally insulated from the heat source, so that a temperature difference occurs between the hot and cold junctions, causing an electrical current of a constant magnitude to flow.

Hydrogen sulfide (H 2S) in urban ambient air

NASA Astrophysics Data System (ADS)

Kourtidis, K.; Kelesis, A.; Petrakakis, M.

Despite indications of high hydrogen sulfide levels in some urban environments, only sparse measurements have been reported in the literature. Here we present one full year of hydrogen sulfide measurements in an urban traffic site in the city of Thessaloniki, Greece. In this 1-million-population city the H 2S concentrations were surprisingly high, with a mean annual concentration of 8 μg m -3 and wintertime mean monthly concentrations up to 20 μg m -3 (12.9 ppb). Daily mean concentrations in the winter were up to 30 μg m -3 (19.3 ppb), while hourly concentrations were up to 54 μg m -3 (34.8 ppb). During calm (wind velocity < 0.5 m s -1) conditions, mainly encountered during night-time hours, hourly values of H 2S were highly correlated with those of CO ( r2 = 0.75) and SO 2 ( r2 = 0.70), pointing to a common traffic source from catalytic converters. Annual mean concentrations are above the WHO recommendation for odor annoyance; hence, H 2S might play a role to the malodorous episodes that the city occasionally experiences. The high ambient H 2S levels might also be relevant to the implementation of preservation efforts for outdoor marble and limestone historical monuments that have been targeting SO 2 emissions as an atmospheric acidity source, since the measurements presented here suggest that about 19% of the annual sulfur (SO 2 + H 2S) emissions in Thessaloniki are in the form of H 2S.

Complexation induced aggregation and deaggregation of acridine orange with sulfobutylether-β-cyclodextrin.

PubMed

Sayed, Mhejabeen; Jha, Shruti; Pal, Haridas

2017-09-13

The present study reports a contrasting interaction behaviour of a biologically important dye, acridine orange (AOH + ), with a highly water soluble anionic host, based on a β-cyclodextrin (βCD) scaffold, i.e. sulfobutylether-β-cyclodextrin (SBEβCD), in comparison to native βCD. AOH + shows striking modulation in its photophysical properties, representing sequential changes in the modes of interaction with increasing SBEβCD concentration. At lower SBEβCD concentrations, AOH + preferentially binds in dimeric forms at the negatively charged SBEβCD portals, leading to strong fluorescence quenching. At higher SBEβCD concentrations, the dimeric dyes convert to monomeric forms and subsequently undergo both inclusion and exo complex formation with 1 : 1 stoichiometry, resulting in a large fluorescence enhancement. The intriguing observation of sequential fluorescence switch off and switch on for an AOH + -SBEβCD system is clearly facilitated by the presence of butylether chains with SO 3 - end groups at the portals of SBEβCD, providing an additional ion-ion interaction and much enhanced hydrophobic interaction for cationic AOH + compared to the native βCD host. To the best of our knowledge, such fluorescence off/on switching through multistep host-guest binding has not been reported so far in the literature. The present study not only provides a detailed insight into the unique binding interactions of AOH + with the SBEβCD host, but the findings of this study are also expected to be useful in designing supramolecular based drug formulations, drug delivery systems, sensors, and so on.

PCA-based SO2, NO2, and HCHO retrievals from GeoTASO airborne measurements during KORUS-AQ 2016 campaign

NASA Astrophysics Data System (ADS)

Chong, H.; Lee, S.; Jeong, U.; Kim, J.; Li, C.; Krotkov, N. A.; Al-Saadi, J. A.; Janz, S. J.; Kowalewski, M. G.; Nowlan, C. R.; Kang, M.; Joiner, J.; Haffner, D. P.; Koo, J. H.; Hong, H.; Lee, H.

2017-12-01

The Geostationary Trace gas and Aerosol Sensor Optimization (GeoTASO) is an airborne instrument measuring backscattered radiance with a spectrometer covering the spectral range between 290-695 nm. GeoTASO flew on the B-200 (UC-12B) - LARC aircraft during the KORUS-AQ campaign, of which the spatial resolution is about 250 nm x 250 m. Principal component analysis (PCA) technique is used to retrieve slant column densities (SCD) of sulfur dioxide (SO2), nitrogen dioxide (NO2), and formaldehyde (HCHO). The fitting windows of SO2, NO2, and HCHO are 310-325 nm, 350-380 nm, and 335-357 nm respectively. The clear PCs of each species are collected from rural areas where are found to have less SCDs of each species from prior iteration step. Using the clear sector PCs and the cross section of each species, SCDs of each trace gas are obtained using the multiple linear regression method. Air mass factors (AMF) of each species are obtained using the atmospheric profiles from chemical transport model calculations during the campaign to convert SCDs to vertical column densities (VCD). The retrieved VCDs of each species well capture small point sources on the flight paths and their plumes propagating downwind areas, which was not available from the ground-based in-situ measurements. The retrieved VCDs will be compared and/or validated against other benchmark measurements during the campaign.

Experimental Investigation of Gas/Slag/Matte/Tridymite Equilibria in the Cu-Fe-O-S-Si System in Controlled Gas Atmosphere: Experimental Results at 1523 K (1250 °C) and P(SO2) = 0.25 atm

NASA Astrophysics Data System (ADS)

Fallah-Mehrjardi, Ata; Hidayat, Taufiq; Hayes, Peter C.; Jak, Evgueni

2018-04-01

To assist in the optimization of copper smelting and converting processes, accurate new measurements of the phase equilibria of the Cu-Fe-O-S-Si system have been undertaken. The experimental investigation was focused on the characterization of gas/slag/matte/tridymite equilibria in the Cu-Fe-O-S-Si system at 1523 K (1250 °C), P(SO2) = 0.25 atm, and a range of P(O2)s. The experimental methodology, developed in PYROSEARCH, includes high-temperature equilibration of samples on substrate made from the silica primary phase in controlled gas atmospheres (CO/CO2/SO2/Ar) followed by rapid quenching of the equilibrium condensed phases and direct measurement of the phase compositions with electron-probe X-ray microanalysis (EPMA). The data provided in the present study at 1523 K (1250 °C) and the previous study by the authors at 1473 K (1200 °C) has enabled the determination of the effects of temperature on the phase equilibria of the multicomponent multiphase system, including such characteristics as the chemically dissolved copper in slag and Fe/SiO2 ratio at silica saturation as a function of copper concentration in matte. The new data will be used in the optimization of the thermodynamic database for the copper-containing systems.

Chile: Political and Economic Conditions and U.S. Relations

DTIC Science & Technology

2009-12-10

achieve full independence until 1818. By 1932, Chile had established a mass electoral democracy, which endured until 1973. During much of this period...by the armed forces and other bodies. 6 Peter M. Siavelis, “ Electoral System, Coalitional Disintegration, and the Future of Chile’s Concertación...finally replaced,” Latin News Weekly Report, August 20, 2009. 13 Monte Reel, “Chile’s Student Activists: A Course in Democracy,” Washington Post

Chile: Political and Economic Conditions and U.S. Relations

DTIC Science & Technology

2010-03-02

until 1818. By 1932, Chile had established a mass electoral democracy, which endured until 1973. During much of this period, Chile was governed by...served as “senators-for-life” and nine senators were designated by the armed forces and other bodies. 14 Peter M. Siavelis, “ Electoral System...Course in Democracy,” Washington Post , November 25, 2006. 24 “Chile: Pinochet-era Education Law Finally Replaced,” Latin News Weekly Report, August 20