36 CFR Appendix D to Part 1191 - Technical

Code of Federal Regulations, 2014 CFR

2014-07-01

... inch (13 mm) high shall be ramped, and shall comply with 405 or 406. 304Turning Space 304.1General... ground space allows a parallel approach to an element and the side reach is unobstructed, the high side....2Obstructed High Reach. Where a clear floor or ground space allows a parallel approach to an element and the...

Test and Evaluation of the Navy Technical Information Presentation System (NTIPS) F-14A Field Test Results

DTIC Science & Technology

1988-09-01

Test and Evaluation Report Test and Evaluation of the Navy Technical Information Presentation System (NTIPS) F-14A Field Test Results by .0 Joseph J...PROGRAM PROJECT TASK WORK UNIT Washington, D.C. 20361 ELEMENT NO. NO. NO. ACCESSION NO. OMN 1820 11. TITLE (Include Security Classification) TEST AND...EVALUATION OF THE NAVY TECHNICAL INFORMATION PRESENTATION SYSTEM (NTIPS) F-14A FIELD TEST RESULTS 12. PERSONAL AUTHOR(S) Fuller, Joseph F. (DTRC) Post

Defense Acquisition Review Journal. Volume 16, Number 2

DTIC Science & Technology

2008-07-01

inquiry from a social constructionist perspective, DoD professionals (both civil servants and military officers) and their clients (political appointees...Christopher R. Paparone, USA (Ret.) The author applies social construction theory to reveal potential blind spots associated with the technical...of incoherency and disorderliness), this article reveals the paradoxical qualities along three socially constructed schemes: the Pentagon world of

A mixed methods investigation into the use of non-technical skills by community and hospital pharmacists.

PubMed

Irwin, A; Weidmann, A E

2015-01-01

Non-technical skills refer to the social and cognitive factors that may influence efficient and safe job performance. Non-technical skills are an important element of patient safety in a variety of health care disciplines, including surgery, anesthesia and nursing. However, the use of non-technical skills in pharmacy practice has not yet been fully assessed. To examine attitudes toward, and use of, non-technical skills by pharmacy personnel. A mixed methods approach was used: An attitude survey explored pharmacy personnel attitudes towards non-technical skills and inter-professional collaboration, with community and hospital pharmacy staff (n = 62). Qualitative interviews were then conducted using the critical incident technique, with community pharmacists (n = 11). The survey results demonstrated differences in the opinions of community and hospital pharmacists on three non-technical skill constructs: team structure, mutual support, and situation monitoring, with community pharmacists reporting significantly more positive attitudes about all three constructs. Both groups reported low levels of collaboration with primary care physicians. The interviews identified five non-technical skills as key elements of successful pharmacist performance from the interview transcripts: teamwork; leadership; task management; situation awareness; decision-making. The survey and interviews identified the non-technical skills that are important to pharmacists. This represents the first step towards the development of a behavioral rating system for training purposes that could potentially improve the non-technical skills of pharmacists and enhance patient safety. Copyright © 2015 Elsevier Inc. All rights reserved.

A Study of Placing Army Requirements on Contract

DTIC Science & Technology

2016-04-01

perhaps being unable to control the external environment, has management authority over business and technical aspects of a specific program. The PM...research is the last element of the planning phase addressing both business and technical considerations. The acquisition team equips themselves with...report is the final product utilizing documented findings and supports the business strategy (DoD, Guidebook for the Acquisition of Services, 2011

List of U.S. Army Research Institute Research and Technical Publications. Fiscal Year 2006

DTIC Science & Technology

2007-08-01

performance support systems and computer-generated simulations powered by artificial intelligence , and super-broad bandwidth. We then present a set of...dialogue, Artificial Intelligence SBIR Phase I Report 61 FY 2006 Books and Book Chapters Durlach, P.J., Neuman, J.L., & Bowens, L.D...mediation of the social intelligence -social performance relationship by social knowledge, was supported for three out of five social performance

Defense AR Journal. Volume 16, Number 2, July 2008

DTIC Science & Technology

2008-07-01

inquiry from a social constructionist perspective, DoD professionals (both civil servants and military officers) and their clients (political appointees...Christopher R. Paparone, USA (Ret.) The author applies social construction theory to reveal potential blind spots associated with the technical...of incoherency and disorderliness), this article reveals the paradoxical qualities along three socially constructed schemes: the Pentagon world of

Theoretical aspects of diagnostics of car as mechatronic system

NASA Astrophysics Data System (ADS)

Goncharov, A. E.; Bondarenko, E. V.; Krasnoshtanov, S. Yu

2018-03-01

The article describes transformation of mechanical systems of automobiles into mechatronic ones due to application of electronic control systems. To assess the relationship of mechanical and electronic components of the mechatronic systems with regard to their technical states, the method of equivalent elements was employed. A mathematical model of changes in the technical state of equivalent elements was developed. It allowed us to present changes in operation capacity in a graphic form. The analytical model is used to ensure operating capacity potential stability for the mechatronic system. For this purpose, new resources were identified with regard to the information ‘field’. Therefore, a new approach to the systematization of knowledge about mechatronic transport systems (D-C-R-E system) is required. The D-C-R-E system is examined as a separate unit. The article describes Information unit formation based on the physical component of the D-C-R-E system and external information which is collected and processed in the Information Diagnostic Center (IDC). Using probability theory and Boolean algebra methods, the authors obtained a logistic model describing information relations between elements of the upgraded D-C-R-E system and contribution of each component to the road safety protection. The logistic model helped formulate main IDC tasks. Implementation of those tasks was transformed into the logical sequence of data collection and analysis in the IDC. That approach predetermined development of the multi-level diagnosing system which made it possible to put in order existing and improved image identification methods and algorithms and to create a diagnosing method for mechatronic systems of cars which reduces labor content and increases accuracy. That approach can help assess the technical state of vehicles with characteristics of mechatronic systems and their transport and environmental safety.

Geospace Plasma Dynamics Laboratory Annual Task Report (FY11)

DTIC Science & Technology

2012-03-01

Site Contractors: Nagendra Singh, Ph.D., Physicist , 0.5 MY Neil Grossbard, M.S., Mathematician , 0.7 MY Visitors: Publications: Articles in...PhD Project Manager Division Chief, RVB This report is published in the interest of scientific and technical...Annual Task Report (FY11) 5c. PROGRAM ELEMENT NUMBER 61102F 6. AUTHOR(S) 5d. PROJECT NUMBER 2311 Daniel Ober 5e. TASK NUMBER

Pedagogy and Japanese Culture in a Distance Learning Environment

ERIC Educational Resources Information Center

Anderson, Bodi O.

2012-01-01

Current theoretical models of distance learning are driven by two impetuses: a technical CMC element, and a pedagogical foundation rooted strongly in the Western world, and driven by social constructivism. By and large these models have been exported throughout the world as-is. However, previous research has hinted at potential problems with these…

Life as a NATO Engineer

DTIC Science & Technology

2010-08-01

NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND...management; leads military in case of specialized survey; supervises more than 25 local civilian employees ; acts as technical expert during contract...Security Assistance Force Head- quarters Camp. I knew I could handle the job of project manager, but wondered about acting as contract manager, technical ex

An Error Analysis for the Finite Element Method Applied to Convection Diffusion Problems.

DTIC Science & Technology

1981-03-01

D TFhG-]NOLOGY k 4b 00 \\" ) ’b Technical Note BN-962 AN ERROR ANALYSIS FOR THE FINITE ELEMENT METHOD APPLIED TO CONVECTION DIFFUSION PROBLEM by I...Babu~ka and W. G. Szym’czak March 1981 V.. UNVI I Of- ’i -S AN ERROR ANALYSIS FOR THE FINITE ELEMENT METHOD P. - 0 w APPLIED TO CONVECTION DIFFUSION ...AOAO98 895 MARYLAND UNIVYCOLLEGE PARK INST FOR PHYSICAL SCIENCE--ETC F/G 12/I AN ERROR ANALYIS FOR THE FINITE ELEMENT METHOD APPLIED TO CONV..ETC (U

Impact of IQ, computer-gaming skills, general dexterity, and laparoscopic experience on performance with the da Vinci surgical system.

PubMed

Hagen, Monika E; Wagner, Oliver J; Inan, Ihsan; Morel, Philippe

2009-09-01

Due to improved ergonomics and dexterity, robotic surgery is promoted as being easily performed by surgeons with no special skills necessary. We tested this hypothesis by measuring IQ elements, computer gaming skills, general dexterity with chopsticks, and evaluating laparoscopic experience in correlation to performance ability with the da Vinci robot. Thirty-four individuals were tested for robotic dexterity, IQ elements, computer-gaming skills and general dexterity. Eighteen surgically inexperienced and 16 laparoscopically trained surgeons were included. Each individual performed three different tasks with the da Vinci surgical system and their times were recorded. An IQ test (elements: logical thinking, 3D imagination and technical understanding) was completed by each participant. Computer skills were tested with a simple computer game (hand-eye coordination) and general dexterity was evaluated by the ability to use chopsticks. We found no correlation between logical thinking, 3D imagination and robotic skills. Both computer gaming and general dexterity showed a slight but non-significant improvement in performance with the da Vinci robot (p > 0.05). A significant correlation between robotic skills, technical understanding and laparoscopic experience was observed (p < 0.05). The data support the conclusion that there are no significant correlations between robotic performance and logical thinking, 3D understanding, computer gaming skills and general dexterity. A correlation between robotic skills and technical understanding may exist. Laparoscopic experience seems to be the strongest predictor of performance with the da Vinci surgical system. Generally, it appears difficult to determine non-surgical predictors for robotic surgery.

REQUIREMENT VERIFICATION AND SYSTEMS ENGINEERING TECHNICAL REVIEW (SETR) ON A COMMERCIAL DERIVATIVE AIRCRAFT (CDA) PROGRAM

DTIC Science & Technology

2017-09-01

the SETR entrance criteria of these events. Out of 30 evaluated SETR entrance criteria, 22 map to FAA elements. A case study of a military CDA...evaluated SETR entrance criteria, 22 map to FAA elements. A case study of a military CDA program, the Presidential Helicopter Replacement Program...3 C. SCOPE AND METHODOLOGY .................................................. 4 D. ORGANIZATION OF THESIS

Undertaking qualitative health research in social virtual worlds.

PubMed

McElhinney, Evelyn; Cheater, Francine M; Kidd, Lisa

2014-06-01

This paper discusses the methodological challenges of using the 3D social virtual world Second Life for research and offers some solutions on a range of research issues including research ethics committee approval, gaining consent, recruitment of sample, data collection and engagement with 'in - world culture'. The attraction of social virtual worlds to researchers is their ability to mimic the physical world, as they, are seen as 'places' where people have a feeling of presence (being there) and social presence (being there with others) through the use of a 'customisable' avatar (digital self-representation). Emerging research demonstrating the persuasive nature of avatars on health behaviours through virtual worlds, online games and the 3D web has increased the use of and interest in these areas for delivering health information, advice and support. However, conducting research can be challenging in a 3D world where people are represented as anonymous avatars in an environment unlike any other online media. 25 semi-structured interviews were conducted in Second Life from September 2011-June 2012. Nurses wishing to undertake research in social virtual worlds should spend time in-world to acquire technical skills and gain an understanding of the culture of the world. Our experience of an interview-based study in virtual worlds indicates that researchers require several virtual world technical skills to create innovative tools to recruit, gain consent and collect data and an understanding of in-world culture, language and social norms to increase the chances of successful research. © 2013 John Wiley & Sons Ltd.

IS/IT Education vs. Business Education: The Plight of Social Collapse in Technical Business Environments

ERIC Educational Resources Information Center

Hall, Brian

2011-01-01

In an age when information, management and technology are supposed to be hand-in-hand, there is often a rift between these elements when considering people and comportment. The detachment is caused by a distressing lack of understanding between Information Systems (IS)/Information Technology (IT) students and professionals and those they interact…

Achieving Adaptability through Inquiry Based Learning

DTIC Science & Technology

2010-06-01

BLACK, Ph.D. MICHELLE SAMS, Ph.D. Research Program Manager Director Training and Leader Development Division Technical review by Marisa...Learning 5a. CONTRACT OR GRANT NUMBER 5b. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) Thomas M. Duffy (Indiana University) and Pamela...ORGANIZATION NAME( S ) AND ADDRESS(ES) School of Education Army Management Staff College Indiana University 5500 21st Street 201

Genome-Enabled Molecular Tools for Reductive Dehalogenation

DTIC Science & Technology

2011-11-01

Genome-Enabled Molecular Tools for Reductive Dehalogenation - A Shift in Paradigm for Bioremediation - Alfred M. Spormann Departments of Chemical...Genome-Enabled Molecular Tools for Reductive Dehalogenation 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d...Applications Technical Session No. 3D C-77 GENOME-ENABLED MOLECULAR TOOLS FOR REDUCTIVE DEHALOGENATION PROFESSOR ALFRED SPORMANN Stanford

[Acceptance of transsexualism among university students from Lódź].

PubMed

Antoszewski, Bogusław; Kasielska, Anna; Jedrzejczak, Marta J; Kruk-Jeromin, Julia

2008-01-01

Transsexualism is one of the gender identity disorders where psychological sex is opposed to anatomical sex. This disorder leads to a discrepancy between the preferred social gender and the biological sex. The aim of this research is to compare knowledge and attitude toward transsexualism in student's opinion, coming from three universities in Lódź. The questionnaire study was performed in the group of 300 students from three universities in Lódź: Technical University of Lódź, University of Lódź, Medical University of Lódź. The questionnaire contained 30 questions related to respondent's sex, birthplace, knowledge about definition and aetiology of transsexualism and also rights which students would grant to transsexuals. The right definition of transsexualism was pointed by 64% of students from Medical University, 57% from Technical University and 40% from University of Lódź. The right to surgical sex change for transsexuals would be granted by 87% of students from the Medical University, 69% from the University of Lódź and 40% from the Technical University. Majority of medical students (90%) and respectively 78% and 57% from the University of Lódź and Technical University would accept a transsexual as his/her co-worker. Student's knowledge about transsexualism is similar and does not differ from a foreign student's knowledge. Students from natural science studies (medicine and biology) are the most tolerant towards transsexuals.

20 CFR 655.1111 - Element I-What hospitals are eligible to participate in the H-1C program?

Code of Federal Regulations, 2010 CFR

2010-04-01

...) hospital,” as defined in Section 1886(d)(1)(B) of the Social Security Act, 42 U.S.C. 1395ww(d)(1)(B), which... settled cost report, filed under Title XVIII of the Social Security Act, (42 U.S.C. 1395 et seq.), for its... settled cost report, filed under Title XVIII of the Social Security Act, for its fiscal year 1994 cost...

20 CFR 655.1111 - Element I-What hospitals are eligible to participate in the H-1C program?

Code of Federal Regulations, 2011 CFR

2011-04-01

...) hospital,” as defined in Section 1886(d)(1)(B) of the Social Security Act, 42 U.S.C. 1395ww(d)(1)(B), which... settled cost report, filed under Title XVIII of the Social Security Act, (42 U.S.C. 1395 et seq.), for its... settled cost report, filed under Title XVIII of the Social Security Act, for its fiscal year 1994 cost...

75 FR 79304 - Technical Corrections to the Standards Applicable to Generators of Hazardous Waste; Alternative...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-20

... the Physical, Engineering, and Life Sciences. 54172, 541720 Research and Development in the Social Sciences and Humanities. What should I consider as I prepare my comments for EPA? A. Submitting CBI. Do not.... In fact, it is in the first element of Part II of the LMP (Sec. 262.214(b)(1)) that eligible academic...

Representation of the quantum Fourier transform on multilevel basic elements by a sequence of selective rotation operators

NASA Astrophysics Data System (ADS)

Ermilov, A. S.; Zobov, V. E.

2007-12-01

To experimentally realize quantum computations on d-level basic elements (qudits) at d > 2, it is necessary to develop schemes for the technical realization of elementary logical operators. We have found sequences of selective rotation operators that represent the operators of the quantum Fourier transform (Walsh-Hadamard matrices) for d = 3-10. For the prime numbers 3, 5, and 7, the well-known method of linear algebra is applied, whereas, for the factorable numbers 6, 9, and 10, the representation of virtual spins is used (which we previously applied for d = 4, 8). Selective rotations can be realized, for example, by means of pulses of an RF magnetic field for systems of quadrupole nuclei or laser pulses for atoms and ions in traps.

Source Methodology for Turbofan Noise Prediction (SOURCE3D Technical Documentation)

NASA Technical Reports Server (NTRS)

Meyer, Harold D.

1999-01-01

This report provides the analytical documentation for the SOURCE3D Rotor Wake/Stator Interaction Code. It derives the equations for the rotor scattering coefficients and stator source vector and scattering coefficients that are needed for use in the TFANS (Theoretical Fan Noise Design/Prediction System). SOURCE3D treats the rotor and stator as isolated source elements. TFANS uses this information, along with scattering coefficients for inlet and exit elements, and provides complete noise solutions for turbofan engines. SOURCE3D is composed of a collection of FORTRAN programs that have been obtained by extending the approach of the earlier V072 Rotor Wake/Stator Interaction Code. Similar to V072, it treats the rotor and stator as a collection of blades and vanes having zero thickness and camber contained in an infinite, hardwall annular duct. SOURCE3D adds important features to the V072 capability-a rotor element, swirl flow and vorticity waves, actuator disks for flow turning, and combined rotor/actuator disk and stator/actuator disk elements. These items allow reflections from the rotor, frequency scattering, and mode trapping, thus providing more complete noise predictions than previously. The code has been thoroughly verified through comparison with D.B. Hanson's CUP2D two- dimensional code using a narrow annulus test case.

Ground Vibration Testing Options for Space Launch Vehicles

NASA Technical Reports Server (NTRS)

Patterson, Alan; Smith, Robert K.; Goggin, David; Newsom, Jerry

2011-01-01

New NASA launch vehicles will require development of robust systems in a fiscally-constrained environment. NASA, Department of Defense (DoD), and commercial space companies routinely conduct ground vibration tests as an essential part of math model validation and launch vehicle certification. Although ground vibration testing must be a part of the integrated test planning process, more affordable approaches must also be considered. A study evaluated several ground vibration test options for the NASA Constellation Program flight test vehicles, Orion-1 and Orion-2, which concluded that more affordable ground vibration test options are available. The motivation for ground vibration testing is supported by historical examples from NASA and DoD. The approach used in the present study employed surveys of ground vibration test subject-matter experts that provided data to qualitatively rank six test options. Twenty-five experts from NASA, DoD, and industry provided scoring and comments for this study. The current study determined that both element-level modal tests and integrated vehicle modal tests have technical merits. Both have been successful in validating structural dynamic math models of launch vehicles. However, element-level testing has less overall cost and schedule risk as compared to integrated vehicle testing. Future NASA launch vehicle development programs should anticipate that some structural dynamics testing will be necessary. Analysis alone will be inadequate to certify a crew-capable launch vehicle. At a minimum, component and element structural dynamic tests are recommended for new vehicle elements. Three viable structural dynamic test options were identified. Modal testing of the new vehicle elements and an integrated vehicle test on the mobile launcher provided the optimal trade between technical, cost, and schedule.

Illustrating anticipatory life cycle assessment for emerging photovoltaic technologies.

PubMed

Wender, Ben A; Foley, Rider W; Prado-Lopez, Valentina; Ravikumar, Dwarakanath; Eisenberg, Daniel A; Hottle, Troy A; Sadowski, Jathan; Flanagan, William P; Fisher, Angela; Laurin, Lise; Bates, Matthew E; Linkov, Igor; Seager, Thomas P; Fraser, Matthew P; Guston, David H

2014-09-16

Current research policy and strategy documents recommend applying life cycle assessment (LCA) early in research and development (R&D) to guide emerging technologies toward decreased environmental burden. However, existing LCA practices are ill-suited to support these recommendations. Barriers related to data availability, rapid technology change, and isolation of environmental from technical research inhibit application of LCA to developing technologies. Overcoming these challenges requires methodological advances that help identify environmental opportunities prior to large R&D investments. Such an anticipatory approach to LCA requires synthesis of social, environmental, and technical knowledge beyond the capabilities of current practices. This paper introduces a novel framework for anticipatory LCA that incorporates technology forecasting, risk research, social engagement, and comparative impact assessment, then applies this framework to photovoltaic (PV) technologies. These examples illustrate the potential for anticipatory LCA to prioritize research questions and help guide environmentally responsible innovation of emerging technologies.

Proceedings of a Conference on a Comprehensive Technical Review of Human Factors Technology in the Design-for-Maintainers Held at Pensacola Beach, Florida on 9-11 March 1982,

DTIC Science & Technology

1982-03-11

Lowery, 1969; Crawford & Altman, 1972; Rigney, Cremer , & Towne, 1965; Topmiller, 1964; see Hsu & Theisen, these Proceedings for a review) suggest...Factors Technical Memorandum No. 6021-1982-05). Warminster, PA: Naval Air Development Center, August 1982. Rigney, J. W., Cremer , R. H., & Towne, D. M. The...changes in the micro-elements. Several projects have employed time-synthesis simulation with generally positive results (Rigney, Cremer , Towne, & Mason

Social research design: framework for integrating philosophical and practical elements.

PubMed

Cunningham, Kathryn Burns

2014-09-01

To provide and elucidate a comprehensible framework for the design of social research. An abundance of information exists concerning the process of designing social research. The overall message that can be gleaned is that numerable elements - both philosophical (ontological and epistemological assumptions and theoretical perspective) and practical (issue to be addressed, purpose, aims and research questions) - are influential in the process of selecting a research methodology and methods, and that these elements and their inter-relationships must be considered and explicated to ensure a coherent research design that enables well-founded and meaningful conclusions. There is a lack of guidance concerning the integration of practical and philosophical elements, hindering their consideration and explication. The author's PhD research into loneliness and cancer. This is a methodology paper. A guiding framework that incorporates all of the philosophical and practical elements influential in social research design is presented. The chronological and informative relationships between the elements are discussed. The framework presented can be used by social researchers to consider and explicate the practical and philosophical elements influential in the selection of a methodology and methods. It is hoped that the framework presented will aid social researchers with the design and the explication of the design of their research, thereby enhancing the credibility of their projects and enabling their research to establish well-founded and meaningful conclusions.

Geometrically nonlinear analysis of laminated elastic structures

NASA Technical Reports Server (NTRS)

Reddy, J. N.; Chandrashekhara, K.; Chao, W. C.

1993-01-01

This final technical report contains three parts: Part 1 deals with the 2-D shell theory and its element formulation and applications. Part 2 deals with the 3-D degenerated element. These two parts constitute the two major tasks that were completed under the grant. Another related topic that was initiated during the present investigation is the development of a nonlinear material model. This topic is briefly discussed in Part 3. To make each part self-contained, conclusions and references are included in each part. In the interest of brevity, the discussions presented are relatively brief. The details and additional topics are described in the references cited.

TFaNS Tone Fan Noise Design/Prediction System. Volume 1; System Description, CUP3D Technical Documentation and Manual for Code Developers

NASA Technical Reports Server (NTRS)

Topol, David A.

1999-01-01

TFaNS is the Tone Fan Noise Design/Prediction System developed by Pratt & Whitney under contract to NASA Lewis (presently NASA Glenn). The purpose of this system is to predict tone noise emanating from a fan stage including the effects of reflection and transmission by the rotor and stator and by the duct inlet and nozzle. These effects have been added to an existing annular duct/isolated stator noise prediction capability. TFaNS consists of: The codes that compute the acoustic properties (reflection and transmission coefficients) of the various elements and write them to files. Cup3D: Fan Noise Coupling Code that reads these files, solves the coupling problem, and outputs the desired noise predictions. AWAKEN: CFD/Measured Wake Postprocessor which reformats CFD wake predictions and/or measured wake data so it can be used by the system. This volume of the report provides technical background for TFaNS including the organization of the system and CUP3D technical documentation. This document also provides information for code developers who must write Acoustic Property Files in the CUP3D format. This report is divided into three volumes: Volume I: System Description, CUP3D Technical Documentation, and Manual for Code Developers; Volume II: User's Manual, TFaNS Vers. 1.4; Volume III: Evaluation of System Codes.

Technical communications in aerospace - An analysis of the practices reported by U.S. and European aerospace engineers and scientists

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.; Glassman, Myron

1990-01-01

The flow of scientific and technical information (STI) at the individual, organizational, national, and international levels is studied. The responses of U.S and European aerospace engineers and scientists to questionnaires concerning technical communications in aerospace are examined. Particular attention is given to the means used to communicate information and the social system of the aerospace knowledge diffusion process. Demographic data about the survey respondents are provided. The methods used to communicate technical data and the sources utilized to solve technical problems are described. The importance of technical writing skills and the use of computer technology in the aerospace field are discussed. The derived data are useful for R&D and information managers in order to improve access to and utilization of aerospace STI.

Can CH-53K 3D Technical Data Support the Provisioning Process

DTIC Science & Technology

2017-05-01

contain the minimum required data characteristics and elements (Appendix A) and (2) are fully anno - tated, they can be converted to 3D PDF files that...were anno - tated as part of the original model development/creation process, the time to perform an annotation would be about 50 percent (about 1.5...files, after the fact. If the models had been anno - tated at the time they were created, we estimate that the cost to implement a 3D PDF solution for

A Recommendation for the Heavy Division Command Group

DTIC Science & Technology

1994-06-03

Numbers. To include contract from the Standard Distribution for and grant numbers; may include program Unclassified Scientific and Technical element...blank. C - Contract PR - Project G - Grant TA -Task PE - Program WU - Work Unit Block 13. Abstract, Include a brief (Maximum Element Accession No. 200...Ronald E. McConnell, M.B.A., M.A. Accepted this 3rd day of June 1994 by. A •" Director, Graduate Degree Philip Brooes, Ph.D. Program The opinions and

COIN 1.0 Formulation

DTIC Science & Technology

2010-05-01

Anderson , C , Keltner , D , John , OP 2003 “Emotional convergence between people over time” Journal of Personality and Social...E T E C H N I C A L R E P O R T COIN 1.0 Formulation The views, opinions and/or findings contained in this report are...Figure 5-35. Animated Time Series DORP 5-37 Figure 36: The elements of power 2 Figure D -1. Agent Schematic

Federal Funding for Education Knowledge Production and Utilization: KPU Function, by Agency. R&D Systems Studies. Technical Report No. 2.

ERIC Educational Resources Information Center

Mason, Ward S.; And Others

This report examines support for education Knowledge Production and Utilization (KPU) using data provided by the National Academy of Sciences (NAS) Study Project on Social Research and Development. The scope of education KPU is discussed in terms of social policy areas relevant to education and activities relevant to KPU. The conceptual framework…

1857-1936.

PubMed

Blázquez Ornat, Isabel

The objective of this study was to reconstruct the professional identity of the practicante (male assistant in medicine and surgery) by analyzing three professional journals of this collective in Zaragoza (Aragón). The discourse of practicantes on their profession insists that they were the only assistants for physicians with technical qualities. This affirmation constituted a key element in shaping their identity, contributing in turn to establish the moral and social legitimization of practicantes and their professional authority. This was constructed in counterpoint to the profile, qualifications and gender identity of the other professional healthcare assistant, the nurse. Despite achieving a clear discourse on their professional identity and developing certain professional infrastructures through the work of institutions and key figures, practicantes were not able to consolidate a collective project of upward social mobility that would improve their status and enhance social recognition of the profession. This led to the construction of a group identity that was largely characterized by apathy, frustration and disunion, elements that eventually weakened the profession.

[Leadership in the health services].

PubMed

Neri, A

1986-01-01

The concept of leadership is not centered on strength of conviction or the ability to inspire support from others. Authority requires obedience, which is unlikely to bring about substantive changes. There are three classical types of leadership: bureaucratic (which depends on the size of one's share of power within an institution), prestige (which depends on one's technical expertise and standing in one's profession), and political (which depends on the extent of one's power in society at large). Prestige leadership pertains to an occupation and applies particularly to the health professions, especially the medical profession. Change is conditioned by factors internal to the health field (such as technological innovations and dissatisfaction with remunerations and social standing in some occupations) and by elements in the social context. These elements include historical situations favorable to change (crises) and forces for preservation of the status quo.

Classification of antecedents towards safety use of health information technology: A systematic review.

PubMed

Salahuddin, Lizawati; Ismail, Zuraini

2015-11-01

This paper provides a systematic review of safety use of health information technology (IT). The first objective is to identify the antecedents towards safety use of health IT by conducting systematic literature review (SLR). The second objective is to classify the identified antecedents based on the work system in Systems Engineering Initiative for Patient Safety (SEIPS) model and an extension of DeLone and McLean (D&M) information system (IS) success model. A systematic literature review (SLR) was conducted from peer-reviewed scholarly publications between January 2000 and July 2014. SLR was carried out and reported based on the preferred reporting items for systematic reviews and meta-analyses (PRISMA) statement. The related articles were identified by searching the articles published in Science Direct, Medline, EMBASE, and CINAHL databases. Data extracted from the resultant studies included are to be analysed based on the work system in Systems Engineering Initiative for Patient Safety (SEIPS) model, and also from the extended DeLone and McLean (D&M) information system (IS) success model. 55 articles delineated to be antecedents that influenced the safety use of health IT were included for review. Antecedents were identified and then classified into five key categories. The categories are (1) person, (2) technology, (3) tasks, (4) organization, and (5) environment. Specifically, person is attributed by competence while technology is associated to system quality, information quality, and service quality. Tasks are attributed by task-related stressor. Organisation is related to training, organisation resources, and teamwork. Lastly, environment is attributed by physical layout, and noise. This review provides evidence that the antecedents for safety use of health IT originated from both social and technical aspects. However, inappropriate health IT usage potentially increases the incidence of errors and produces new safety risks. The review cautions future implementation and adoption of health IT to carefully consider the complex interactions between social and technical elements propound in healthcare settings. Copyright © 2015. Published by Elsevier Ireland Ltd.

Robots and service innovation in health care.

PubMed

Oborn, Eivor; Barrett, Michael; Darzi, Ara

2011-01-01

Robots have long captured our imagination and are being used increasingly in health care. In this paper we summarize, organize and criticize the health care robotics literature and highlight how the social and technical elements of robots iteratively influence and redefine each other. We suggest the need for increased emphasis on sociological dimensions of using robots, recognizing how social and work relations are restructured during changes in practice. Further, we propose the usefulness of a 'service logic' in providing insight as to how robots can influence health care innovation. The Royal Society of Medicine Press Ltd 2011.

United States Air Force Graduate Student Summer Support Program (1987). Program Technical Report. Volume 1.

DTIC Science & Technology

1987-12-01

developed for a large percentage of the participants in the Summer Faculty Research Program in 1979-1983 period through an AFOSR Minigrant Program . On 1...Analysis of a Bimodal Nuclear Rocket Core by Dav,, C. Carpenter ABSTRACT The framework for a general purpose finite element analysis code was developed ...to study the 2-D temperature distribution in a hot-channel S hexagonal fuel element in the core of a bimodal nuclear’ rocket. Prelim- inary thermal

Activating Technology for Connected Health in Cancer: Protocol for a Research and Training Program.

PubMed

Mountford, Nicola; Dorronzoro Zubiete, Enrique; Kessie, Threase; Garcia-Zapirain, Begonya; Nuño-Solinís, Roberto; Coyle, David; Munksgaard, Kristin B; Fernandez-Luque, Luis; Rivera Romero, Octavio; Mora Fernandez, Matilde; Valero Jimenez, Pedro; Daly, Ailish; Whelan, Ruth; Caulfield, Brian

2018-01-24

As cancer survival rates increase, the challenge of ensuring that cancer survivors reclaim their quality of life (QoL) becomes more important. This paper outlines the research element of a research and training program that is designed to do just that. Bridging sectors, disciplines, and geographies, it brings together eight PhD projects and students from across Europe to identify the underlying barriers, test different technology-enabled rehabilitative approaches, propose a model to optimize the patient pathways, and examine the business models that might underpin a sustainable approach to cancer survivor reintegration using technology. The program, funded under the European Union's Horizon 2020 research and innovation program under the Marie Sklodowska-Curie grant agreement No 722012, includes deep disciplinary PhD projects, intersectoral and international secondments, interdisciplinary plenary training schools, and virtual subject-specific education modules. The 8 students have now been recruited and are at the early stages of their projects. CATCH will provide a comprehensive training and research program by embracing all key elements-technical, social, and economic sciences-required to produce researchers and project outcomes that are capable of meeting existing and future needs in cancer rehabilitation. ©Nicola Mountford, Enrique Dorronzoro Zubiete, Threase Kessie, Begonya Garcia-Zapirain, Roberto Nuño-Solinís, David Coyle, Kristin B Munksgaard, Luis Fernandez-Luque, Octavio Rivera Romero, Matilde Mora Fernandez, Pedro Valero Jimenez, Ailish Daly, Ruth Whelan, Brian Caulfield. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 24.01.2018.

Group Recommendation in Social Networks

DTIC Science & Technology

2011-01-01

APPROVAL SHEET Title of Thesis: Group recognition in social networks Name of Candidate: Nagapradeep Chinnam Master of...2011 4. TITLE AND SUBTITLE Group recognition in social networks 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d...for public release; distribution unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT Recent years have seen an exponential growth in the use of social

2D and 3D GPR imaging of structural ceilings in historic and existing constructions

NASA Astrophysics Data System (ADS)

Colla, Camilla

2014-05-01

GPR applications in civil engineering are to date quite diversified. With respect to civil constructions and monumental buildings, detection of voids, cavities, layering in structural elements, variation of geometry, of moisture content, of materials, areas of decay, defects, cracks have been reported in timber, concrete and masonry elements. Nonetheless, many more fields of investigation remain unexplored. This contribution gives an account of a variety of examples of structural ceilings investigation by GPR radar in reflection mode, either as 2D or 3D data acquisition and visualisation. Ceilings have a pre-eminent role in buildings as they contribute to a good structural behaviour of the construction. Primarily, the following functions can be listed for ceilings: a) they carry vertical dead and live loads on floors and distribute such loads to the vertical walls; b) they oppose to external horizontal forces such as wind loads and earthquakes helping to transfer such forces from the loaded element to the other walls; c) they contribute to create the box skeleton and behaviour of a building, connecting the different load bearing walls and reducing the slenderness and flexural instability of such walls. Therefore, knowing how ceilings are made in specific buildings is of paramount importance for architects and structural engineers. According to the type of building and age of construction, ceilings may present very different solutions and materials. Moreover, in existing constructions, ceilings may have been substituted, modified or strengthened due to material decay or to change of use of the building. These alterations may often go unrecorded in technical documentation or technical drawings may be unavailable. In many cases, the position, orientation and number of the load carrying elements in ceilings may be hidden or not be in sight, due for example to the presence of false ceilings or to technical plants. GPR radar can constitute a very useful tool for investigating with rapidity and high resolution, thin as well as very thick ceilings, in a non-destructive manner. Ceilings may be made up as masonry vaults or timber/metal/concrete beams and elements laid down in one or two directions or, again, can be made as a combination of the above. A number of cases are here presented reporting on typical features to be recognised in radargrams in order to distinguish the material and possible shape of the relevant objects with the aim of providing a first small catalogue useful to the radar user and to professionals. This abstract is of interest for COST Action TU1208.

A socio-technical critique of tiered services: implications for interprofessional care.

PubMed

Hood, Rick

2015-01-01

In the health and social care sector, tiered services have become an increasingly influential way of organising professional expertise to address the needs of vulnerable people. Drawing on its application to UK child welfare services, this paper discusses the merits of the tiered model from a socio-technical perspective - an approach that has emerged from the fields of accident analysis and systems design. The main elements of a socio-technical critique are outlined and used to explore how tiered services provide support to families and prevent harm to children. Attention is drawn to the distribution of expertise and resources in a tiered system, and to the role of referral and gate-keeping procedures in dispersing accountability for outcomes. An argument is made for designing systems "against demand", and the paper concludes by discussing some alternative models of multi-agency provision.

Technical Leadership Development Program-Year 3

DTIC Science & Technology

2012-08-30

Develop an understanding of why achieving technology-based competitive advantage can be part of firm’s business strategy.  Review the Porter Model ...NUMBER H98230-08-D-0171 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) Gavito /Dr. Valentin 5d. PROJECT NUMBER RT 4-3 5e. TASK...NUMBER WHS TO009 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Stevens Institute of Technology 8. PERFORMING ORGANIZATION

Achieving Education for Technological Capability in Scotland

ERIC Educational Resources Information Center

McLaren, Susan V.

2003-01-01

Design and technology (D&T) education involves learners coping creatively with complexity. It must take account of a wide range of often apparently conflicting demands and constraints: aesthetic, economic, political, ethical, social, and environmental as well as ergonomic, technical, and scientific. Case study tasks describe a relatively…

Structural Analysis of Technical-Tactical Elements in Table Tennis and their Role in Different Playing Zones

PubMed Central

Munivrana, Goran; Petrinović, Lidija Zekan; Kondrič, Miran

2015-01-01

For the purpose of determining the overall structure of technical-tactical elements in table tennis and evaluating their role in different playing zones around the table, a new measuring instrument (a questionnaire) was formulated that took advantage of the expert knowledge of top, world class table tennis coaches. The results of the hierarchical taxonomic (cluster) analysis showed that the overall structure of the technical-tactical elements forming the table tennis technique could be divided into three basic groups; a group of technical-tactical elements (A) used in the phase of preparing one’s own and disabling the opponent’s attack; a group of technical-tactical elements (B) used in the phase of attack and counterattack; and a group of technical-tactical elements (C) used in the phase of defense. The differences among the obtained groups of table tennis elements were determined by applying the Kruskal-Wallis test, while relations between the groups and their role in different playing zones around the table were analyzed by comparing the average values of the experts’ scores. PMID:26557204

Structural Analysis of Technical-Tactical Elements in Table Tennis and their Role in Different Playing Zones.

PubMed

Munivrana, Goran; Petrinović, Lidija Zekan; Kondrič, Miran

2015-09-29

For the purpose of determining the overall structure of technical-tactical elements in table tennis and evaluating their role in different playing zones around the table, a new measuring instrument (a questionnaire) was formulated that took advantage of the expert knowledge of top, world class table tennis coaches. The results of the hierarchical taxonomic (cluster) analysis showed that the overall structure of the technical-tactical elements forming the table tennis technique could be divided into three basic groups; a group of technical-tactical elements (A) used in the phase of preparing one's own and disabling the opponent's attack; a group of technical-tactical elements (B) used in the phase of attack and counterattack; and a group of technical-tactical elements (C) used in the phase of defense. The differences among the obtained groups of table tennis elements were determined by applying the Kruskal-Wallis test, while relations between the groups and their role in different playing zones around the table were analyzed by comparing the average values of the experts' scores.

Assessing Explosives Safety Risks, Deviations, And Consequences

DTIC Science & Technology

2009-07-31

Technical Paper 23 31 July 2009 DDESB Assessing Explosives Safety Risks, Deviations, And Consequences ...Deviations, And Consequences 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER...and approaches to assist warfighters in executing their mission, conserving resources, and maximizing operational effectiveness . When mission risk

Development of a Multifuel Individual/Squad Stove

DTIC Science & Technology

1990-02-01

1 . Final Letter Report, Fix Verification Test of the MISS, U.S. Army CRTC , April 1989. m. Health Hazard Assessment, 4 April 1989, enclosed. n...CIVIL, 1 \\48ABIpPTR TECHNICAL REPORT __...__AD _ NATICK/TR-90/020 ceq DEVELOPMENT OF A00 O MULTIFUEL o INDIVIDUAL/SQUAD STOVE N I O BY DONALD W...NUMBERS PROGRAM PROJECT ITASK ~ WORK UNIT ELEMENT NO. NO. NO. ACCESSION NO. D5i48 24 1 146 TITLE (Include Security Classification) D 2 Development of a

Guide to Technical Documents. Volume 2. January 1982 through December 1982

DTIC Science & Technology

1982-12-01

and could weigh 600 MN (133 x 10 Ib) submerged. R-11 S.... -- R-854-1 R-850 A Finite Element Head Injury Model, Vol. 1: Theory , Efficiency Study of...winter freezeback has been parameters for the classical theories of plasticity and visco- apparent, this movement is minimal compared to settlement...from 0% to 35%, depending on the structures’ t/D ° ADA089300 and L/D o ratios, from that reported previously. Theory is formulated for effects of an

Solar Systems

NASA Technical Reports Server (NTRS)

1979-01-01

The solar collectors shown are elements of domestic solar hot water systems produced by Solar One Ltd., Virginia Beach, Virginia. Design of these systems benefited from technical expertise provided Solar One by NASA's Langley Research Center. The company obtained a NASA technical support package describing the d e sign and operation of solar heating equipment in NASA's Tech House, a demonstration project in which aerospace and commercial building technology are combined in an energy- efficient home. Solar One received further assistance through personal contact with Langley solar experts. The company reports that the technical information provided by NASA influenced Solar One's panel design, its selection of a long-life panel coating which increases solar collection efficiency, and the method adopted for protecting solar collectors from freezing conditions.

A Bibliography of Research on the Influence of Irrelevant Information on Psychological Judgments

DTIC Science & Technology

1981-09-01

Kansas State University " I 00 -.HUMAN FACTORS TECHNICAL AREA C.3)(iiA € U.S. Army LUResearch Institute for the Behavioral and Social Sciences... Behavioral September 1981 and Social Sciences, 5001 Eisenhower Avenue, 13. NUMBER OF PAGES Alexandria, VA 22333 10 14. MONITORING AGENCY NAME & ADDRESS(if...81. Anderson, N. H., & Grant, D. A. A test of a statisticil learning theory model for two-choice behavior models with double stimulus events. Journal

Addressing social aspects associated with wastewater treatment facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Padilla-Rivera, Alejandro; Morgan-Sagastume, Juan Manuel; Noyola, Adalberto

In wastewater treatment facilities (WWTF), technical and financial aspects have been considered a priority, while other issues, such as social aspects, have not been evaluated seriously and there is not an accepted methodology for assessing it. In this work, a methodology focused on social concerns related to WWTF is presented. The methodology proposes the use of 25 indicators as a framework for measuring social performance to evaluate the progress in moving towards sustainability. The methodology was applied to test its applicability and effectiveness in two WWTF in Mexico (urban and rural). This evaluation helped define the key elements, stakeholders andmore » barriers in the facilities. In this context, the urban facility showed a better overall performance, a result that may be explained mainly by the better socioeconomic context of the urban municipality. Finally, the evaluation of social aspects using the semi-qualitative approach proposed in this work allows for a comparison between different facilities and for the identification of strengths and weakness, and it provides an alternative tool for achieving and improving wastewater management. - Highlights: • The methodology proposes 25 indicators as a framework for measuring social performance in wastewater treatment facilities. • The evaluation helped to define the key elements, stakeholders and barriers in the wastewater treatment facilities. • The evaluation of social aspects allows the identification of strengths and weakness for improving wastewater management. • It provides a social profile of the facility that highlights the best and worst performances.« less

Characteristics of a virtual community for individuals who are d/deaf and hard of hearing.

PubMed

Shoham, Snunith; Heber, Meital

2012-01-01

The content of 2,050 messages on a virtual forum for d/Deaf and hard of hearing people in Israel was analyzed. Interactions and behavior were monitored to determine if behavior on the forum expressed social support, and whether the community was an entirely virtual community or a real community whose members also met in other venues. Subjects discussed in messages included technical difficulties, coping with difficulties presented by hearing loss, adjusting to assistive devices, difficulties at school and work, accessibility issues, difficulties communicating with the hearing world, and rights. Messages were also used to initiate a range of social activities. Classification of behaviors per the Social Support Behavior Code (Cutrona & Suhr, 1992) showed that most were in the category of informational support. Other types of support in the model, tangible assistance, emotional support, social network support, and esteem support, were evident in fewer messages.

The Cosmos on a Shoestring. Small Spacecraft for Space and Earth Science

DTIC Science & Technology

1998-01-01

uniform microwave profile. The MAP (553 kg) mission will complete a survey of the cosmos with a sensitiv - ity two orders of magnitude greater than...economic, ecological, social , and technical risks to which the project is exposed. It requires an understand- ing of the elements that drive risk...give high priority to reducing risks below historical values. The effect of a mis- sion loss on public and media interest in space must also be

Alternatives to Address Role Clarification at the U.S. Army Community Hospital, Fort Polk

DTIC Science & Technology

1981-06-01

Szilagyi , Andrew D., and Wallace , Marc J., Organizational Behavior and Performance (Santa Monica: Goodyear Publishing Company, 1977): Page 214. 14...Institute For Social Research, The University of Michigan, Ann Arbor, Michigan, 1972. Ivancevich, John M., Szilagyi , Andrew D. and Wallace , Marc J...opposed to professional and technical groups. 1 1 Another study by Szilagyi and Sims postulated the existence of a role ambiguity continuum which revealed

Experimental and Numerical Analysis of Structural Acousticcontrol Interior Noise Reduction

NASA Technical Reports Server (NTRS)

Mei, Chuh; Bevan, Jeffrey S.

1999-01-01

The research results contained in this technical report were performed under the NASA grant entitled "Experimental and Numerical Structural Acoustic Control for Interior Noise Reduction". The report is based essentially on partial progress of the Ph.D. dissertation prepared by Jeffrey S. Bevan under direct guidance of Dr. Chuh Mei. The document presents a finite element formulation and control of sound radiated from cylindrical panels embedded with piezoceramic actuators. The extended MIN6 shallow shell element is fully electrical-structural coupled. A piezoelectric modal actuator participation (PMAP) is defined which indicates the actuator performance to each of the offending modes. Genetic algorithm is also employed to validate the sensor and actuator locations determined by the PMAP criteria. The work was conducted at the Department of Aerospace Engineering, Old Dominion University. Mr. Travis L. Turner, Structural Acoustics Branch, NASA Langley Research Center is the technical monitor.

Fertility decline and social service access: reconciling behavioral and medical models.

PubMed

Weinstein, J

1978-01-01

In this summary of fertility literature the author attempts to differentiate between the effects of behavioral and medical models of family planning programs on the fertility rate. This is done by determining the effects of access to social welfare services by assessment of: the function of children within the family life survey conducted in the Cameroons are also used. It was found that 7 interdependent elements of social service are involved: 1) general health care; 2) social security for sick and aged; 3) employment training and opportunities for adults; 4) literacy and education; 5) communication and transportation systems; 6) housing and infrastructure; 7) child care and welfare. The presence of these elements is shown to accompany low fertility while their absence is expressed in high rates of child bearing. These elements are major variables in both the nomological and public policy senses. 2 additional components are knowledge of and favorable attitudes towards effective means of fertility control plus effective mechanical, chemical, or natural means of limiting fertility. The concept of fertility norm and its impact on the fertility rate is explained as being the result of the collective force which social affiliations exert on people to reproduce in a certain way. The "stopping rule" is that which will fulfill the fertility norm. An example of this is a culture which continues child bearing until a son has been born and then controls reproduction after this has happened. Such factors must be considered for family planning programs to succeed in these cultures. Therefore fertility levels are found to be the product of prevailing norms and technical ability to achieve these norms. Improvement in levels of access to social services can bring about the lowering of these norms.

75 FR 9548 - Reduction of Use of Social Security Numbers (SSN) in the Department of Defense (DoD)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-03

... authorization to receive specific categories of information. Computer network. The constituent element of an... elements reside on a computer. Form. A fixed arrangement of captioned spaces designed for entering and... activities of the Government or because of the information value of the data in them. Survey. An instrument...

Neutron Resonance Radiography for Explosives Detection: Technical Challenges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raas, W L; Blackburn, B; Boyd, E

2005-11-09

Fast Neutron Resonance Radiography (NRR) has recently become a focus of investigation as a supplement to conventional x-ray systems as a non-invasive, non-destructive means of detecting explosive material concealed in checked luggage or cargo containers at airports. Using fast (1-6 MeV) neutrons produced by the D(d,n){sup 3}He reaction, NRR provides both an imaging capability and the ability to determine the chemical composition of materials in baggage or cargo. Elemental discrimination is achieved by exploiting the resonance features of the neutron cross-section for oxygen, nitrogen, carbon, and hydrogen. Simulations have shown the effectiveness of multiple-element NRR through Monte Carlo transport methods;more » this work is focused on the development of a prototype system that will incorporate an accelerator-based neutron source and a neutron detection and imaging system to demonstrate the realistic capabilities of NRR in distinguishing the elemental components of concealed objects. Preliminary experiments have exposed significant technical difficulties unapparent in simulations, including the presence of image contamination from gamma ray production, the detection of low-fluence fast neutrons in a gamma field, and the mechanical difficulties inherent in the use of thin foil windows for gas cell confinement. To mitigate these concerns, a new gas target has been developed to simultaneously reduce gamma ray production and increase structural integrity in high flux gas targets. Development of a neutron imaging system and neutron counting based on characteristic neutron pulse shapes have been investigated as a means of improving signal to noise ratios, reducing irradiation times, and increasing the accuracy of elemental determination.« less

Ecological Systems Theory: Using Spheres of Influence to Support Small-unit Climate and Training

DTIC Science & Technology

2016-03-01

identifying the model’s elements and influential individuals, define spheres of influence and construct a model that details the ecological systems...Research Report 1997 Ecological Systems Theory: Using Spheres of Influence to Support Small-unit Climate and Training...Technical review by: Sena Garven, U.S. Army Research Institute Michael D. Wood , Walter Reed Army Institute of Research

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. Blair Briggs; Robert W. Schaefer

Richard D. McKnight passed away on 28 August 2013. Dick was known to most for his technical excellence; leadership; and kind, thoughtful demeanor. The authors have attempted to capture, in a few short pages, elements of each of those qualities that defined Dick McKnight. The authors will then conclude with some personal memories of a man they looked to as a dear colleague, mentor, and friend.

Determinants of sustainability in solid waste management--the Gianyar Waste Recovery Project in Indonesia.

PubMed

Zurbrügg, Christian; Gfrerer, Margareth; Ashadi, Henki; Brenner, Werner; Küper, David

2012-11-01

According to most experts, integrated and sustainable solid waste management should not only be given top priority, but must go beyond technical aspects to include various key elements of sustainability to ensure success of any solid waste project. Aside from project sustainable impacts, the overall enabling environment is the key feature determining performance and success of an integrated and affordable solid waste system. This paper describes a project-specific approach to assess typical success or failure factors. A questionnaire-based assessment method covers issues of: (i) social mobilisation and acceptance (social element), (ii) stakeholder, legal and institutional arrangements comprising roles, responsibilities and management functions (institutional element); (iii) financial and operational requirements, as well as cost recovery mechanisms (economic element). The Gianyar Waste Recovery Project in Bali, Indonesia was analysed using this integrated assessment method. The results clearly identified chief characteristics, key factors to consider when planning country wide replication but also major barriers and obstacles which must be overcome to ensure project sustainability. The Gianyar project consists of a composting unit processing 60 tons of municipal waste per day from 500,000 inhabitants, including manual waste segregation and subsequent composting of the biodegradable organic fraction. Copyright © 2012 Elsevier Ltd. All rights reserved.

Technical instrumentation R&D for ILD SiW ECAL large scale device

NASA Astrophysics Data System (ADS)

Balagura, V.

2018-03-01

Calorimeters with silicon detectors have many unique features and are proposed for several world-leading experiments. We describe the R&D program of the large scale detector element with up to 12 000 readout channels for the International Large Detector (ILD) at the future e+e‑ ILC collider. The program is focused on the readout front-end electronics embedded inside the calorimeter. The first part with 2 000 channels and two small silicon sensors has already been constructed, the full prototype is planned for the beginning of 2018.

Material Modeling for Terminal Ballistic Simulation

DTIC Science & Technology

1992-09-01

DYNA-3D-a nonlinear, explicit, three-dimensional finite element code for solid and structural mechanics- user manual. Technical Report UCRL -MA...Rep. UCRL -50108, Rev. 1, Lawrence Livermore Laboratory, 1977. [34] S. P. Marsh. LASL Shock Hugoniot Data. University of California Press, Berkeley, CA...Steinberg. Equation of state and strength properties of selected ma- teriaJs. Tech. Rep. UCRL -MA-106439, Lawrence Livermore National Labo- ratory, 1991. [371

EMOTIONAL INTELLIGENCE, MORAL, ETHICS, BIO-ETHICS AND WHAT IS IN BETWEEN.

PubMed

Keidar, Daniella; Yagoda, Arie

2014-10-01

In recent years, the study of emotions has broadened its scope and established its standing as a new scientific discipline. Humanity has become increasingly conscious of the seminal role played by the emotional components in both intrapersonal and interpersonal behavior. A deeply rooted and inherent correlation exists between emotional intelligence (E.I. - Emotional Intelligence) and positive social results: social adaptation, quality social relationships, the capacity for healthy social behaviors, caring, altruism, empathy, enlightened communication and the efficacy and personal coherence essential to moral and ethical behavior, including its manifestation in the sphere of bio-ethics. The importance of the personal relationship between the doctor and the patient is especially fundamental in the current era of immense and accelerated scientific-technological development, forcing doctors to cope with an increasingly complicated technical environment. Precisely because of this reality, it is essential that a doctor's actions and interpersonal relationship with the patient proceed from an ethical base, grounded in both professional and emotional responsibility. Emotional responsibility is one of the central elements underlying bioethical conduct and is the element that provides the guideposts for the treatment of others. The symbiotic connection between emotional intelligence and the sphere of ethics and morals is what delineates human beings. Human beings, by definition and in essence, bear responsibility for their actions. The beginning of ethics is in the human being's consciousness of choice in relation to self and to others. An individual's choices integrate emotion and cognition. That ability to integrate alongside the capacity for choice enables the human race to act in accordance with ethical and moral codes. At work, on a daily basis, a doctor is positioned opposite to the physical, emotional, cognitive and ethical entirety of the patient. Beyond the doctor's technical ability to heal, there also exists his capacity to create within the patient the desire to heal.

The Technical Communicator as Advocate: Integrating a Social Justice Approach in Technical Communication

ERIC Educational Resources Information Center

Jones, Natasha N.

2016-01-01

This article argues for the need for a social justice approach to technical communication research and pedagogy. Given previous calls by scholars in technical and professional communication (TPC) for an attention to diversity, inclusion, and equality, the author examines the place and purpose of social justice in TPC and provides useful approaches…

Comparison of a traditional with a new approach based on Graph Theory to vulnerability assessment to natural hazards: a study case on a socio-economic complex system

NASA Astrophysics Data System (ADS)

Arosio, Marcello; Martina, Mario L. V.

2017-04-01

The emergent behaviour of the contemporary complex, socio-technical and interconnected society makes the collective risk greater than the sum of the parts and this requires a holistic, systematic and integrated approach. Although there have been major improvements in recent years, there are still some limitation in term of a holistic approach that is able to include the emergent value hidden in the connections between exposed elements and the interactions between the different spheres of the multi-hazards, vulnerability, exposure and resilience. To deal with these challenges it is necessary to consider the connections between the exposed elements (e.g. populations, schools, hospital, etc.) and to quantify the relative importance of the elements and their interconnections (e.g. the need of injured people to go to hospital or children to school). In a system (e.g. road, hospital and ecological network, etc.), or in a System of System (e.g. socio-technical urban service), there are critical elements that, beyond the intrinsic vulnerability, can be characterized by greater or lower vulnerability because of their physical, geographical, cyber or logical connections. To this aim, we propose in this study a comparative analysis between traditional reductionist approach and a new holistic approach to vulnerability assessment to natural hazards. The analysis considers a study case of a socio-economic complex system through an innovative approach based on the properties of graph G=(N,L). A graph consists of two sets N (nodes) and L (links): the nodes represent the single exposed elements (physical, social, environmental, etc.) to a hazard, while the links (or connections) represent the interaction between the elements. The final goal is to illustrate an application of this innovative approach of integrated collective vulnerability assessment.

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of technical assistance to migrant health centers and entities which intend to become migrant health centers... the grant award, such technical and other nonfinancial assistance (such as fiscal and program...

Feasibility study of an Integrated Program for Aerospace vehicle Design (IPAD). Volume 5: Catalog of IPAD technical program elements

NASA Technical Reports Server (NTRS)

Gillette, W. B. (Editor); Southall, J. W. (Editor)

1973-01-01

The catalog is presented of technical program elements which are required to support the design activities for a subsonic and supersonic commercial transport. Information for each element consists of usage and storage information, ownership, status and an abstract describing the purpose of the element.

The Path to Convergence: Design, Coordination and Social Issues in the Implementation of a Middleware Data Broker.

NASA Astrophysics Data System (ADS)

Slota, S.; Khalsa, S. J. S.

2015-12-01

Infrastructures are the result of systems, networks, and inter-networks that accrete, overlay and segment one another over time. As a result, working infrastructures represent a broad heterogeneity of elements - data types, computational resources, material substrates (computing hardware, physical infrastructure, labs, physical information resources, etc.) as well as organizational and social functions which result in divergent outputs and goals. Cyber infrastructure's engineering often defaults to a separation of the social from the technical that results in the engineering succeeding in limited ways, or the exposure of unanticipated points of failure within the system. Studying the development of middleware intended to mediate interactions among systems within an earth systems science infrastructure exposes organizational, technical and standards-focused negotiations endemic to a fundamental trait of infrastructure: its characteristic invisibility in use. Intended to perform a core function within the EarthCube cyberinfrastructure, the development, governance and maintenance of an automated brokering system is a microcosm of large-scale infrastructural efforts. Points of potential system failure, regardless of the extent to which they are more social or more technical in nature, can be considered in terms of the reverse salient: a point of social and material configuration that momentarily lags behind the progress of an emerging or maturing infrastructure. The implementation of the BCube data broker has exposed reverse salients in regards to the overall EarthCube infrastructure (and the role of middleware brokering) in the form of organizational factors such as infrastructural alignment, maintenance and resilience; differing and incompatible practices of data discovery and evaluation among users and stakeholders; and a preponderance of local variations in the implementation of standards and authentication in data access. These issues are characterized by their role in increasing tension or friction among components that are on the path to convergence and may help to predict otherwise-occluded endogenous points of failure or non-adoption in the infrastructure.

48 CFR 315.305 - Proposal evaluation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... following elements: (1) An explanation of the evaluation process and the role of evaluators throughout the... include, at a minimum, the following elements: (1) A list of recommended technical evaluation panel... that the technical evaluation will have in the award decision. (2) The technical evaluation process...

A focus on the consumer: social marketing for change.

PubMed

Lucaire, L E

1985-01-01

Social marketing is the application of commercial marketing principles to advance a social cause, issue, behavior, product, or service. Social marketing has added a framework to social efforts that heretofore lacked organization and has inspired projects that otherwise might never have been initiated. In the US, social marketing techniques have been particularly successful in the health field. Although advertising and other communications are central to social marketing, the discipline also depends upon other elements of what is termed the marketing mix: product, price, place, and promotion. Social marketing is a cyclical process involving 6 steps: analysis; planning; development, testing, and refining elements of the plan; implementation; assessment of in-market effectiveness; and feedback. In developing countries, health has similarly been the greatest beneficiary to date of applied social marketing techniques. Family planning programs and oral rehydration therapy (ORT) projects have used social marketing techniques effectively in numerous developing countries. Social marketing has been even more widely applied in the sale of contraceptives in developing countries. Contraceptive social marketing (CSM) programs are well established in Bangladesh, Sri Lanka, India, Thailand, Nepal, Colombia, El Salvador, Jamaica, Mexico, and Egypt. More recently programs have been established in Honduras, Guatemala, Barbados, St. Vincent, and St. Lucia. SOMARC (Social Marketing for Change) is a project funded by the US Agency for International Development (AID) and is working with existing CSM programs and helping to launch new CSM programs. CSM programs are successfully functioning as legitimate marketing organizations in developing countries and are using local private sector resources in the process. Program results are encouraging. Social marketing requires both experience and sensitivity to local conditions. Many developing countries now have their own marketing resources. Local private sector advertising and marketing agencies are helping public and private sector programs. In countries where local resources are scarce, AID has created several programs to provide technical assistance in social marketing.

LCROSS - Lunar Impactor: Pioneering Risk-Tolerant Exploration in Search for Water on the Moon

NASA Technical Reports Server (NTRS)

Andrews, Daniel R.

2010-01-01

The Lunar CRater Observation and Sensing Satellite (LCROSS) was launched with the Lunar Reconnaissance Orbiter (LRO) on June 18, 2009 to determine the presence of water-ice in a permanently shadowed crater on the south pole of the Moon. However, an equally important purpose was to pioneer low-cost, quick-turnaround NASA missions that could accept a higher-than-normal-level of technical risk. When the LCROSS mission proposal was competitively selected by the NASA Exploration Systems Mission Directorate to design, build, and launch a spacecraft in 31 months with a $79M cost-capped budget and a fixed mass allocation, NASA Ames Research Center and its industry partner, Northrop-Grumman, needed a game-changing approach to be successful. That approach was a ground-breaking combination of having a risk-tolerant NASA Class D mission status and finding the right balance point between the inflexible elements of cost and schedule and the newly-flexible element of technical capability.

Formation des enseignants dans une perspective d'education permanente au benin

NASA Astrophysics Data System (ADS)

Agboton, Sébastien; Moussa, Yaya Mede

1994-05-01

The history of teacher training in Benin, which provides evidence of social and cultural change, suggests that a system of lifelong education should be introduced which unites formal, non-formal and informal education, all of which already exist in embryo. The education originally given to every member of society was a continuing progression from initiate to initiator, a lifelong education that involved, among other things, knowledge of agricultural production. This traditional system was disrupted by the reorganization of teacher training after 1945. Recurrent training of teachers remained inadequate because of limited external funding for in-service training, the lack of teachers, the suspension of recruitment and the closure of teacher training colleges. The 1975 reform, through the initiative known as Operation Education and Development, envisaged links between school and social environment, allying intellectual work with production. This meant a radical change in the role of the teacher, who was confronted with technical advance and was obliged to enter a difficult continuing process of self-training. Furthermore, population growth and the restrictions imposed by the World Bank have brought about developments in both lifelong learning and apprenticeship. These two elements are brought together under an initiative known as Production Scolaire Artisanale, designed for out-of-school learners and artisans. The author concludes that the creation of a coherent system of voluntary education would be possible in a society that was itself favourably disposed to education.

Sex Differences in Technical Communication: A Perspective from Social Role Theory

ERIC Educational Resources Information Center

Thompson, Isabelle

2004-01-01

This article interprets technical communication research about sex differences according to social role theory, which argues that sex differences are enculturated through experiences associated with social positions in the family and the workplace. It reevaluates technical communication research about sex differences in communicative and…

Glenn T. Seaborg - Contributions to Advancing Science

Science.gov Websites

. Documents: The First Weighing of Plutonium (Atomic Number 94); DOE Technical Report; September 1967 The New Element Americium (Atomic Number 95); DOE Technical Report; January 1948 The New Element Curium (Atomic Number 96); DOE Technical Report; January 1948 Frontiers of Chemistry for Americium and Curium; DOE

78 FR 70586 - Technical Support Document: Technical Update of the Social Cost of Carbon for Regulatory Impact...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-26

... OFFICE OF MANAGEMENT AND BUDGET Technical Support Document: Technical Update of the Social Cost of... Budget, Executive Office of the President. ACTION: Notice of availability and request for comments. SUMMARY: The Office of Management and Budget (OMB) requests comments on the Technical Support Document...

Exploring the Role of Social Memory of Floods for Designing Flood Early Warning Operations

NASA Astrophysics Data System (ADS)

Girons Lopez, Marc; Di Baldassarre, Giuliano; Grabs, Thomas; Halldin, Sven; Seibert, Jan

2016-04-01

Early warning systems are an important tool for natural disaster mitigation practices, especially for flooding events. Warnings rely on near-future forecasts to provide time to take preventive actions before a flood occurs, thus reducing potential losses. However, on top of the technical capacities, successful warnings require an efficient coordination and communication among a range of different actors and stakeholders. The complexity of integrating the technical and social spheres of warning systems has, however, resulted in system designs neglecting a number of important aspects such as social awareness of floods thus leading to suboptimal results. A better understanding of the interactions and feedbacks among the different elements of early warning systems is therefore needed to improve their efficiency and therefore social resilience. When designing an early warning system two important decisions need to be made regarding (i) the hazard magnitude at and from which a warning should be issued and (ii) the degree of confidence required for issuing a warning. The first decision is usually taken based on the social vulnerability and climatic variability while the second one is related to the performance (i.e. accuracy) of the forecasting tools. Consequently, by estimating the vulnerability and the accuracy of the forecasts, these two variables can be optimized to minimize the costs and losses. Important parameters with a strong influence on the efficiency of warning systems such as social awareness are however not considered in their design. In this study we present a theoretical exploration of the impact of social awareness on the design of early warning systems. For this purpose we use a definition of social memory of flood events as a proxy for flood risk awareness and test its effect on the optimization of the warning system design variables. Understanding the impact of social awareness on warning system design is important to make more robust warnings that can better adapt to different social settings and more efficiently reduce vulnerability.

Virtual Human Role Players for Studying Social Factors in Organizational Decision Making

PubMed Central

Khooshabeh, Peter; Lucas, Gale

2018-01-01

The cyber domain of military operations presents many challenges. A unique element is the social dynamic between cyber operators and their leadership because of the novel subject matter expertise involved in conducting technical cyber tasks, so there will be situations where senior leaders might have much less domain knowledge or no experience at all relative to the warfighters who report to them. Nonetheless, it will be important for junior cyber operators to convey convincing information relevant to a mission in order to persuade or influence a leader to make informed decisions. The power dynamic will make it difficult for the junior cyber operator to successfully influence a higher ranking leader. Here we present a perspective with a sketch for research paradigm(s) to study how different factors (normative vs. informational social influence, degree of transparency, and perceived appropriateness of making suggestions) might interact with differential social power dynamics of individuals in cyber decision-making contexts. Finally, we contextualize this theoretical perspective for the research paradigms in viable training technologies. PMID:29545759

Composite Socio-Technical Systems: A Method for Social Energy Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yingchen; He, Fulin; Hao, Jun

In order to model and study the interactions between social on technical systems, a systemic method, namely the composite socio-technical systems (CSTS), is proposed to incorporate social systems, technical systems and the interaction mechanism between them. A case study on University of Denver (DU) campus grid is presented in paper to demonstrate the application of the proposed method. In the case study, the social system, technical system, and the interaction mechanism are defined and modelled within the framework of CSTS. Distributed and centralized control and management schemes are investigated, respectively, and numerical results verifies the feasibility and performance of themore » proposed composite system method.« less

[Change management: An analysis of actors; perceptions about technical assistance in the Democratic Republic of Congo].

PubMed

Ribesse, Nathalie; Iyeti, Alain; Macq, Jean

2015-01-01

Technical assistance (TA) is a common component of health system strengthening interventions. This type of intervention is too often designed and evaluated according to a logic that fails to take into account social complexity. Actors' perceptions are one element of this complexity. This article presents a study conducted in the Democratic Republic of Congo designed to identify perceptions concerning two types of technical support providers for health system strengthening: long-term technical assistants (agents of development agencies) and provincial technical advisors (agents of the Ministry of Health). Interviews were conducted with an innovative tool inspired by the principles of systems thinking. Interviewees were actors involved in a TA intervention in the province of Bandundu. Their expectations regarding TA providers were identified in terms of personal characteristics (knowledge, know-how and interpersonal skills), roles, and styles of interaction for capacity building ("interventionist/ prescriptive axes"). Interviewees emphasized the importance of mutual learning and the quality of interactions, which depends on TA provider's interpersonal skills and mutual willingness. Perceptions of TA provider's characteristics tend to be similar, but several differences were observed concerning the expectations about the roles of TAs, and the style that should be adopted for capacity building. Ignoring these differences in expectations may be a threat to the effectiveness of TA.

Thermally Optimized Paradigm of Thermal Management (TOP-M)

DTIC Science & Technology

2017-07-18

ELEMENT NUMBER 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 6. AUTHOR(S) 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8...19b. TELEPHONE NUMBER (Include area code) 18-07-2017 Final Technical Jul 2015 - Jul 2017 NICOP - Thermally Optimized Paradigm of Thermal Management ...The main goal of this research was to present a New Thermal Management Approach, which combines thermally aware Very/Ultra Large Scale Integration

Sensei: A Multi-Modal Framework for Assessing Stress Resiliency

DTIC Science & Technology

2013-05-01

Modal Framework for Assessing Stress Resiliency (May 1-31, 2013) From: Ajay Divakaran, Technical Leader Jeffrey Lubin, Senior Research Scientist...17 (May 2013): Task 3.1: Capture Behavioral Stress Markers in Real-Time in Lab Environment with graded exposure to ICT’s scenarios MAC 1-6...Modal Framework for Assessing Stress Resiliency 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER

Principles of Work Sample Testing. 4. Generalizability

DTIC Science & Technology

1979-04-01

ARI TECHNICAL REPORT TR-79-A11 Principles of Work Sample Testing: IV. Generallzability , by ,lobert M. Guion Gail H. Ironson BOWLING GREEN STATE...UNIVERSITY Bowling Green , Ohio 43403 April 1979 or -Contract DAHC 19-77-C-0007 d CD, LUa.J Prepared for -_J ;=U.S. ARMY RESEARCH INSTITUTE for the...ORGANIZATION NAME AND ADDRESS 10. PROG RAM ELEMENT. PROJECT, TASK A REA & WORK UNIT NUMBERS Bowling Green State University __ Bowling Green , Ohio 43403

Advanced Multifunctional Materials for High Speed Combatant Hulls

DTIC Science & Technology

2015-11-25

Combatant Hulls 5a. CONTRACT NUMBER 5b. GRANT NUMBER N00014-14-1-0269 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Mark S. Mirotznik 5d. PROJECT...High Speed Combatant Hulls ’ PI Information: Mark S. Mirotznik, Associate Professor Tel: (302) 831 -4241 Department of Electrical and Computer... HULLS FINAL TECHNICAL REPORT 1.0 Abstract In this ONR funded project investigators at the University of Delaware’s Department of Electrical

Systems Engineering Technical Leadership Development Program

DTIC Science & Technology

2012-08-30

technology-based competitive advantage can be part of firm’s business strategy.  Review the Porter Model . Return to Syllabus UNCLASSIFIED 66...Program 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7...PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Stevens Institute of Technology,Systems Engineering Research Center,Castle Point on the Hudson,Hoboken,NJ

Welding technologies as applied to nuclear manufacturing

NASA Astrophysics Data System (ADS)

Roper, J. R.

1992-10-01

This is the trip report of John R. Roper, who traveled to England 25 Sep. through 8 Oct. 1992. Dr. Roper attended the US/UK JOWOG 22-D Joining Technical Exchange meeting and gave a presentation on Welding Finite Element Analysis and the Precision Joining Center at the Atomic Weapons Establishment in Aldermaston, United Kingdom. Dr. Roper also toured the Welding Institute in Abington, UK and discussed technology exchange of weld thermal and mechanical material responses.

[The visual perception of the elements of technical drawings among masking distractions in advanced and nonadvanced students in the building and architectural professions].

PubMed

Balichev, Iu

1997-01-01

To investigation were submitted the particularities of the process of visual perception of technical drawings and schemes in advanced and backward pupils, who were mastering the specialties of "building and architecture", "hydroconstruction", "transport construction", "geodesy". The time was registered, which was necessary to advanced and backward pupils for unveiling the different elements in the drawing, scheme, and such attributes of the drawing as: orientation, length, curves of the lined, the boundary between them; time for identification of the specific designations, symbols, group of symbols, elements of the sketch from the simple to the complex ones. The results of the investigations revealed that in the advanced pupils the perception (unveiling) of the different elements of the technical drawing proceeded very rapidly, almost automatically. In the backward pupils this process elapsed reliably more slowly. It was demonstrated that the growing up pupils, who were distinguished with more rapid perception of the different elements of the drawing (advanced ones) more rapidly and more exactly dealt with solution of the technical tasks as compared with these, who more slowly unveiled the looked for elements (backwardness). Some other individual particularities were also established with respect to the visual perception of the elements of the technical drawing and its properties in advanced and backward pupils who were mastering the investigated professions.

The Social Perspective and Pedagogy in Technical Communication.

ERIC Educational Resources Information Center

Thralls, Charlotte; Blyler, Nancy Roundy

1993-01-01

Notes that as teachers integrate social theory into the technical communication classroom, they interpret the connection between writing and culture in different ways. Describes four social pedagogies of writing--the social constructionist, the ideologic, the social cognitive, and the paralogic hermeneutic--distinguishing them by their pedagogic…

Valorisation of urban elements through 3D models generated from image matching point clouds and augmented reality visualization based in mobile platforms

NASA Astrophysics Data System (ADS)

Marques, Luís.; Roca Cladera, Josep; Tenedório, José António

2017-10-01

The use of multiple sets of images with high level of overlapping to extract 3D point clouds has increased progressively in recent years. There are two main fundamental factors in the origin of this progress. In first, the image matching algorithms has been optimised and the software available that supports the progress of these techniques has been constantly developed. In second, because of the emergent paradigm of smart cities which has been promoting the virtualization of urban spaces and their elements. The creation of 3D models for urban elements is extremely relevant for urbanists to constitute digital archives of urban elements and being especially useful for enrich maps and databases or reconstruct and analyse objects/areas through time, building and recreating scenarios and implementing intuitive methods of interaction. These characteristics assist, for example, higher public participation creating a completely collaborative solution system, envisioning processes, simulations and results. This paper is organized in two main topics. The first deals with technical data modelling obtained by terrestrial photographs: planning criteria for obtaining photographs, approving or rejecting photos based on their quality, editing photos, creating masks, aligning photos, generating tie points, extracting point clouds, generating meshes, building textures and exporting results. The application of these procedures results in 3D models for the visualization of urban elements of the city of Barcelona. The second concerns the use of Augmented Reality through mobile platforms allowing to understand the city origins and the relation with the actual city morphology, (en)visioning solutions, processes and simulations, making possible for the agents in several domains, to fundament their decisions (and understand them) achieving a faster and wider consensus.

When social behaviour is moulded in clay: on growth and form of social insect nests.

PubMed

Perna, Andrea; Theraulaz, Guy

2017-01-01

The nests built by social insects are among the most complex structures produced by animal groups. They reveal the social behaviour of a colony and as such they potentially allow comparative studies. However, for a long time, research on nest architecture was hindered by the lack of technical tools allowing the visualisation of their complex 3D structures and the quantification of their properties. Several techniques, developed over the years, now make it possible to study the organisation of these nests and how they are built. Here, we review present knowledge of the mechanisms of nest construction, and how nest structure affects the behaviour of individual insects and the organisation of activities within a colony. © 2017. Published by The Company of Biologists Ltd.

The coevolution of innovation and technical intelligence in primates

PubMed Central

Street, Sally E.; Whalen, Andrew; Laland, Kevin N.

2016-01-01

In birds and primates, the frequency of behavioural innovation has been shown to covary with absolute and relative brain size, leading to the suggestion that large brains allow animals to innovate, and/or that selection for innovativeness, together with social learning, may have driven brain enlargement. We examined the relationship between primate brain size and both technical (i.e. tool using) and non-technical innovation, deploying a combination of phylogenetically informed regression and exploratory causal graph analyses. Regression analyses revealed that absolute and relative brain size correlated positively with technical innovation, and exhibited consistently weaker, but still positive, relationships with non-technical innovation. These findings mirror similar results in birds. Our exploratory causal graph analyses suggested that technical innovation shares strong direct relationships with brain size, body size, social learning rate and social group size, whereas non-technical innovation did not exhibit a direct relationship with brain size. Nonetheless, non-technical innovation was linked to brain size indirectly via diet and life-history variables. Our findings support ‘technical intelligence’ hypotheses in linking technical innovation to encephalization in the restricted set of primate lineages where technical innovation has been reported. Our findings also provide support for a broad co-evolving complex of brain, behaviour, life-history, social and dietary variables, providing secondary support for social and ecological intelligence hypotheses. The ability to gain access to difficult-to-extract, but potentially nutrient-rich, resources through tool use may have conferred on some primates adaptive advantages, leading to selection for brain circuitry that underlies technical proficiency. PMID:26926276

The coevolution of innovation and technical intelligence in primates.

PubMed

Navarrete, Ana F; Reader, Simon M; Street, Sally E; Whalen, Andrew; Laland, Kevin N

2016-03-19

In birds and primates, the frequency of behavioural innovation has been shown to covary with absolute and relative brain size, leading to the suggestion that large brains allow animals to innovate, and/or that selection for innovativeness, together with social learning, may have driven brain enlargement. We examined the relationship between primate brain size and both technical (i.e. tool using) and non-technical innovation, deploying a combination of phylogenetically informed regression and exploratory causal graph analyses. Regression analyses revealed that absolute and relative brain size correlated positively with technical innovation, and exhibited consistently weaker, but still positive, relationships with non-technical innovation. These findings mirror similar results in birds. Our exploratory causal graph analyses suggested that technical innovation shares strong direct relationships with brain size, body size, social learning rate and social group size, whereas non-technical innovation did not exhibit a direct relationship with brain size. Nonetheless, non-technical innovation was linked to brain size indirectly via diet and life-history variables. Our findings support 'technical intelligence' hypotheses in linking technical innovation to encephalization in the restricted set of primate lineages where technical innovation has been reported. Our findings also provide support for a broad co-evolving complex of brain, behaviour, life-history, social and dietary variables, providing secondary support for social and ecological intelligence hypotheses. The ability to gain access to difficult-to-extract, but potentially nutrient-rich, resources through tool use may have conferred on some primates adaptive advantages, leading to selection for brain circuitry that underlies technical proficiency. © 2016 The Author(s).

[Social politics against poverty and in favor of health in Mexico].

PubMed

Hamui-Sutton, Alicia; Irigoyen-Coria, Arnulfo; Gómez-Clavelina, Francisco Javier; Fernández-Ortega, Miguel Angel

2006-01-01

One of the biggest challenges that Mexico faces is to fight against the poverty. The transition of a characteristic welfare model from the government in a closed economy, to an open economy where the functions of the State are limited, has modified the modalities of the social politics against poverty. Six indispensable conditions are identified for poverty's reduction: 1. Economic development with stability in order to generate more and better jobs for poor people. 2. To improve regional economies. 3. To improve home conditions of poor people. 4. To elevate education levels (to encourage an authentic heath education). 5. To diminish catastrophic expenses for health problems. 6. Technical training for all workers. The impact of poverty over health can provide valuable elements to establish effective preventive strategies on health workers.

The Use of Dynamic Stochastic Social Behavior Models to Produce Likelihood Functions for Risk Modeling of Proliferation and Terrorist Attacks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, Jonathan; Thompson, Sandra E.; Brothers, Alan J.

The ability to estimate the likelihood of future events based on current and historical data is essential to the decision making process of many government agencies. Successful predictions related to terror events and characterizing the risks will support development of options for countering these events. The predictive tasks involve both technical and social component models. The social components have presented a particularly difficult challenge. This paper outlines some technical considerations of this modeling activity. Both data and predictions associated with the technical and social models will likely be known with differing certainties or accuracies – a critical challenge is linkingmore » across these model domains while respecting this fundamental difference in certainty level. This paper will describe the technical approach being taken to develop the social model and identification of the significant interfaces between the technical and social modeling in the context of analysis of diversion of nuclear material.« less

Theorising big IT programmes in healthcare: strong structuration theory meets actor-network theory.

PubMed

Greenhalgh, Trisha; Stones, Rob

2010-05-01

The UK National Health Service is grappling with various large and controversial IT programmes. We sought to develop a sharper theoretical perspective on the question "What happens - at macro-, meso- and micro-level - when government tries to modernise a health service with the help of big IT?" Using examples from data fragments at the micro-level of clinical work, we considered how structuration theory and actor-network theory (ANT) might be combined to inform empirical investigation. Giddens (1984) argued that social structures and human agency are recursively linked and co-evolve. ANT studies the relationships that link people and technologies in dynamic networks. It considers how discourses become inscribed in data structures and decision models of software, making certain network relations irreversible. Stones' (2005) strong structuration theory (SST) is a refinement of Giddens' work, systematically concerned with empirical research. It views human agents as linked in dynamic networks of position-practices. A quadripartite approcach considers [a] external social structures (conditions for action); [b] internal social structures (agents' capabilities and what they 'know' about the social world); [c] active agency and actions and [d] outcomes as they feed back on the position-practice network. In contrast to early structuration theory and ANT, SST insists on disciplined conceptual methodology and linking this with empirical evidence. In this paper, we adapt SST for the study of technology programmes, integrating elements from material interactionism and ANT. We argue, for example, that the position-practice network can be a socio-technical one in which technologies in conjunction with humans can be studied as 'actants'. Human agents, with their complex socio-cultural frames, are required to instantiate technology in social practices. Structurally relevant properties inscribed and embedded in technological artefacts constrain and enable human agency. The fortunes of healthcare IT programmes might be studied in terms of the interplay between these factors. Copyright 2010 Elsevier Ltd. All rights reserved.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 16: Aerospace knowledge diffusion research

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Kennedy, John M.; Barclay, Rebecca O.; White, Terry F.; Jones, Ray (Editor)

1991-01-01

The project is a cooperative US effort between NASA, DoD, and Indiana University. This research was endorsed by the AGARD Technical Information Panel and the American Institute of Aeronautics and Astronautics (AIAA) Technical Information Committee. The four-phase inquiry focuses on scientific and technical information (STI) as knowledge, the channels through which this knowledge is communicated, and the members of the social system associated with and involved in diffusing this knowledge throughout the aerospace community. The project is based on two premises: (1) although STI is essential to innovation, STI by itself does not ensure innovation; and (2) utilizing existing STI or creating new STI, does often facilitate technological innovation. The topics covered include the following: information-seeking habits, knowledge transfer, academic sector, non-US organizations, present status, comparative study, and timetable.

A Framework for Understanding and Generating Integrated Solutions for Residential Peak Energy Demand

PubMed Central

Buys, Laurie; Vine, Desley; Ledwich, Gerard; Bell, John; Mengersen, Kerrie; Morris, Peter; Lewis, Jim

2015-01-01

Supplying peak energy demand in a cost effective, reliable manner is a critical focus for utilities internationally. Successfully addressing peak energy concerns requires understanding of all the factors that affect electricity demand especially at peak times. This paper is based on past attempts of proposing models designed to aid our understanding of the influences on residential peak energy demand in a systematic and comprehensive way. Our model has been developed through a group model building process as a systems framework of the problem situation to model the complexity within and between systems and indicate how changes in one element might flow on to others. It is comprised of themes (social, technical and change management options) networked together in a way that captures their influence and association with each other and also their influence, association and impact on appliance usage and residential peak energy demand. The real value of the model is in creating awareness, understanding and insight into the complexity of residential peak energy demand and in working with this complexity to identify and integrate the social, technical and change management option themes and their impact on appliance usage and residential energy demand at peak times. PMID:25807384

A framework for understanding and generating integrated solutions for residential peak energy demand.

PubMed

Buys, Laurie; Vine, Desley; Ledwich, Gerard; Bell, John; Mengersen, Kerrie; Morris, Peter; Lewis, Jim

2015-01-01

Supplying peak energy demand in a cost effective, reliable manner is a critical focus for utilities internationally. Successfully addressing peak energy concerns requires understanding of all the factors that affect electricity demand especially at peak times. This paper is based on past attempts of proposing models designed to aid our understanding of the influences on residential peak energy demand in a systematic and comprehensive way. Our model has been developed through a group model building process as a systems framework of the problem situation to model the complexity within and between systems and indicate how changes in one element might flow on to others. It is comprised of themes (social, technical and change management options) networked together in a way that captures their influence and association with each other and also their influence, association and impact on appliance usage and residential peak energy demand. The real value of the model is in creating awareness, understanding and insight into the complexity of residential peak energy demand and in working with this complexity to identify and integrate the social, technical and change management option themes and their impact on appliance usage and residential energy demand at peak times.

Characterizing Resilience and Growth Among Soldiers: A Trajectory Study

DTIC Science & Technology

2014-04-01

0120 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER Nansook Park 5e. TASK NUMBER e -mail: nspak@umich.edu 5f. WORK UNIT NUMBER 7...tried all available methods to reach potential participants including e -mail, regular mail, phone and social media like Facebook. We were able to...utilize all possible ways of contacting participants including e -mail, regular mail, phone calls, and social media (e.g., Facebook). Furthermore

R.D. Laing's theological hinterland: the contrast between mysticism and communion.

PubMed

Miller, Gavin

2012-06-01

Contrasting elements in R.D. Laing's psychiatry can be traced to two kinds of Christian theology: mystical theology and corporate theology. On one hand, Laing's mystical theology combined with psychoanalytic theory, to provide a New Age psychotherapeutic account of the recovery of authentic selfhood via metanoia. On the other, his incarnational, corporate theology promoted social inclusion of the mentally ill, particularly via therapeutic communities. For Laing, as for other post-war British Christians, a turn inwards, to mysticism and the sacralization of the self, and a turn outwards, to social and political activism, were ways of negotiating with the decline of traditional Christianity.

Judgement Day: Prosecuting Jihadist Terrorism as a Criminal Enterprise under the Military Commissions Act

DTIC Science & Technology

2007-04-01

racketeering can prove that enterprise is separate from the pattern of racketeering.); River City Mkts., Inc. v. Fleming Foods West, Inc., 960 F.2d 1458...of a different element between separate sales to the same buyer). 102 See United States v. Usama Bin Laden, _ F.Supp. 2d _, (S.D.N.Y., 2001); 2001...11.106 Diagnostic and social science experts can help MCA prosecutors explain a jihadist perpetrator’s political violence, and the mental and physical

Experiments in Sound and Structural Vibrations Using an Air-Analog Model Ducted Propulsion System

DTIC Science & Technology

2007-08-01

Department of Aerospace S~and Mechanical Engineering I 20070904056 I EXPERIMENTS IN SOUND AND STRUCTURAL VIBRATIONS USING AN AIR -ANALOG MODEL DUCTED...SOUND AND STRUCTURAL * VIBRATIONS USING AN AIR -ANALOG MODEL DUCTED PROPULSION SYSTEM FINAL TECHNICAL REPORT Prepared by: Scott C. Morris Assistant...Vibration Using Air - 5b. GRANT NUMBER Analog Model Ducted Propulsion Systems N00014-1-0522 5C. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER

Cramer-Rao Bound, MUSIC, and Maximum Likelihood. Effects of Temporal Phase Difference

DTIC Science & Technology

1990-11-01

Technical Report 1373 November 1990 Cramer-Rao Bound, MUSIC , And Maximum Likelihood Effects of Temporal Phase o Difference C. V. TranI OTIC Approved... MUSIC , and Maximum Likelihood (ML) asymptotic variances corresponding to the two-source direction-of-arrival estimation where sources were modeled as...1pI = 1.00, SNR = 20 dB ..................................... 27 2. MUSIC for two equipowered signals impinging on a 5-element ULA (a) IpI = 0.50, SNR

Mechanics of Air-Inflated Drop-Stitch Fabric Panels Subject to Bending Loads

DTIC Science & Technology

2013-08-15

Division Newport and Navatek, Ltd. The technical reviewer was Geoffrey R. Moss (Code 1522). The authors gratefully acknowledge Martin S . Leff and...to Bending Loads 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) Paul V. Cavallaro Christopher J. Hart Ali M...Sadegh 5.d PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Naval Undersea Warfare

Nonlinear Real-Time Optical Signal Processing.

DTIC Science & Technology

1984-10-01

I 1.8 IIII III1 1 / U , 0 7 USCIPI Report 1130 E ~C~,OUTfitA N Ivj) UNIVERSITY OF SOUTHERN CALIFORNIA - I FINAL TECHNICAL REPORT April 15, 1981 - June...30, 1984 N NONLINEAR REAL-TIME OPTICAL SIGNAL PROCESSING i E ~ A.A. Sawchuk, Principal Investigator T.C. Strand and A.R. Tanguay. Jr. October 1, 1984...Erter.d) logic system. A computer generated hologram fabricated on an e -beam system serves as a beamsteering interconnection element. A completely

Disrespectful intrapartum care during facility-based delivery in sub-Saharan Africa: A qualitative systematic review and thematic synthesis of women's perceptions and experiences.

PubMed

Bradley, Susan; McCourt, Christine; Rayment, Juliet; Parmar, Divya

2016-11-01

The psycho-social elements of labour and delivery are central to any woman's birth experience, but international efforts to reduce maternal mortality in low-income contexts have neglected these aspects and focused on technological birth. In many contexts, maternity care is seen as dehumanised and disrespectful, which can have a negative impact on utilisation of services. We undertook a systematic review and meta-synthesis of the growing literature on women's experiences of facility-based delivery in sub-Saharan Africa to examine the drivers of disrespectful intrapartum care. Using PRISMA guidelines, databases were searched from 1990 to 06 May 2015, and 25 original studies were included for thematic synthesis. Analytical themes, that were theoretically informed and cognisant of the cultural and social context in which the dynamics of disrespectful care occur, enabled a fresh interpretation of the factors driving midwives' behaviour. A conceptual framework was developed to show how macro-, meso- and micro-level drivers of disrespectful care interact. The synthesis revealed a prevailing model of maternity care that is institution-centred, rather than woman-centred. Women's experiences illuminate midwives' efforts to maintain power and control by situating birth as a medical event and to secure status by focusing on the technical elements of care, including controlling bodies and knowledge. Midwives and women are caught between medical and social models of birth. Global policies encouraging facility-based delivery are forcing women to swap the psycho-emotional care they would receive from traditional midwives for the technical care that professional midwives are currently offering. Any action to change the current performance and dynamic of birth relies on the participation of midwives, but their voices are largely missing from the discourse. Future research should explore their perceptions of the value and practice of interpersonal aspects of maternity care and the impact of disrespectful care on their sense of professionalism and personal ethics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Grayscale photomask fabricated by laser direct writing in metallic nano-films.

PubMed

Guo, Chuan Fei; Cao, Sihai; Jiang, Peng; Fang, Ying; Zhang, Jianming; Fan, Yongtao; Wang, Yongsheng; Xu, Wendong; Zhao, Zhensheng; Liu, Qian

2009-10-26

The grayscale photomask plays a key role in grayscale lithography for creating 3D microstructures like micro-optical elements and MEMS structures, but how to fabricate grayscale masks in a cost-effective way is still a big challenge. Here we present novel low cost grayscale masks created in a two-step method by laser direct writing on Sn nano-films, which demonstrate continuous-tone gray levels depended on writing powers. The mechanism of the gray levels is due to the coexistence of the metal and the oxides formed in a laser-induced thermal process. The photomasks reveal good technical properties in fabricating 3D microstructures for practical applications.

Student-driven courses on the social and ecological responsibilities of engineers : commentary on "student-inspired activities for the teaching and learning of engineering ethics".

PubMed

Baier, André

2013-12-01

A group of engineering students at the Technical University of Berlin, Germany, designed a course on engineering ethics. The core element of the developed Blue Engineering course are self-contained teaching-units, "building blocks". These building blocks typically cover one complex topic and make use of various teaching methods using moderators who lead discussions, rather than experts who lecture. Consequently, the students themselves started to offer the credited course to their fellow students who take an active role in further developing the course themselves.

3D printing in social education: Eki-Fab and student PBL

NASA Astrophysics Data System (ADS)

Makino, Masato; Saito, Azusa; Kodama, Mai; Takamatsu, Kyuuichiro; Tamate, Hideaki; Sakai, Kazuyuki; Wada, Masato; Khosla, Ajit; Kawakami, Masaru; Furukawa, Hidemitsu

2017-04-01

Additive manufacturing or 3D printer is one of the most innovative material processing methods. We are considering that human resources for 3D printing would be needed in the future. To educate the abilities of the digital fabrication, we have the public digital fabrication space "Eki-Fab" for junior and high school students and Project Based Learning (PBL) class for undergraduate students. Eki-Fab is held on every Saturday at the Yonezawa train station. In the "Eki-Fab", anybody can study the utilizing of 3D printer and modeling technics under the instruction of staff in Yamagata University. In the PBL class, we have the class every Thursday. The students get the techniques of the digital fabrication through the PBL.

An Exploration of Cyberspace Security R&D Investment Strategies for DARPA: "The Day After. . . in Cyberspace II",

DTIC Science & Technology

1996-01-01

Automated Teller Machine networks malfunction in Georgia 2000 May 20 CNN off air for 12 minutes; issues special report 2000 May 20 worm...password combinations, social security and credit card numbers, account information, health status, and innumerable other sensitive information...as follows: TW/AA Issues Recommended Technical Response Possible Implementation Obstacles 1. (re Tactical Warning) • Place automated software

2D-3D μXRF elemental mapping of archeological samples

NASA Astrophysics Data System (ADS)

Hampai, D.; Liedl, A.; Cappuccio, G.; Capitolo, E.; Iannarelli, M.; Massussi, M.; Tucci, S.; Sardella, R.; Sciancalepore, A.; Polese, C.; Dabagov, S. B.

2017-07-01

Recently opened for users at LNF XLab-Frascati a μ XRF station, named "Rainbow X-ray" - RXR, has been optimized for most of X-ray analytical research fields. The basic principle of the station is in the use of various geometrical combinations of polycapillary optics for X-ray beam shaping (focusing/collimation) at specially designed laboratory unit. In this work we have presented the results of archaeological studies on the artifacts of Paleolithic period and Iron Age (9th century BC to the midway of the 8th BC). The elemental analysis of these artifacts has been first performed by compact laboratory setup. Superficial (2D) and bulk (3D) micro-fluorescence mapping provides useful informations for the geologists in order to identify the possible artifacts provenience and origin. The results presented in this work are a part of wider anthropological/archeological investigations aimed at the understanding of social and economical relations of prehistorical communities.

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements B2: Education. Technical Report 49B2

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element, including its purpose, values, base populations and…

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements A: Demographics. Technical Report 49A

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

This technical paper contains information about the variables in the LSAY (Longitudinal Surveys of Australian Youth) Y95 cohort data set. It groups each variable into data elements which identifies common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements C: Employment. Technical Report 49C

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

Computer-analyzed facial expression as a surrogate marker for autism spectrum social core symptoms.

PubMed

Owada, Keiho; Kojima, Masaki; Yassin, Walid; Kuroda, Miho; Kawakubo, Yuki; Kuwabara, Hitoshi; Kano, Yukiko; Yamasue, Hidenori

2018-01-01

To develop novel interventions for autism spectrum disorder (ASD) core symptoms, valid, reliable, and sensitive longitudinal outcome measures are required for detecting symptom change over time. Here, we tested whether a computerized analysis of quantitative facial expression measures could act as a marker for core ASD social symptoms. Facial expression intensity values during a semi-structured socially interactive situation extracted from the Autism Diagnostic Observation Schedule (ADOS) were quantified by dedicated software in 18 high-functioning adult males with ASD. Controls were 17 age-, gender-, parental socioeconomic background-, and intellectual level-matched typically developing (TD) individuals. Statistical analyses determined whether values representing the strength and variability of each facial expression element differed significantly between the ASD and TD groups and whether they correlated with ADOS reciprocal social interaction scores. Compared with the TD controls, facial expressions in the ASD group appeared more "Neutral" (d = 1.02, P = 0.005, PFDR < 0.05) with less variation in Neutral expression (d = 1.08, P = 0.003, PFDR < 0.05). Their expressions were also less "Happy" (d = -0.78, P = 0.038, PFDR > 0.05) with lower variability in Happy expression (d = 1.10, P = 0.003, PFDR < 0.05). Moreover, the stronger Neutral facial expressions in the ASD participants were positively correlated with poorer ADOS reciprocal social interaction scores (ρ = 0.48, P = 0.042). These findings indicate that our method for quantitatively measuring reduced facial expressivity during social interactions can be a promising marker for core ASD social symptoms.

Where the lay and the technical meet: Using an anthropology of interfaces to explain persistent reproductive health disparities in West Africa.

PubMed

Jaffré, Yannick; Suh, Siri

2016-05-01

Despite impressive global investment in reproductive health programs in West Africa, maternal mortality remains unacceptably high and obstetric care is often inadequate. Fertility is among the highest in the world, while contraceptive prevalence remains among the lowest. This paper explores the social and technical dimensions of this situation. We argue that effective reproductive health programs require analyzing the interfaces between technical programs and the social logics and behaviors of health professionals and client populations. Significant gaps between health programs' goals and the behaviors of patients and health care professionals have been observed. While public health projects aim to manage reproduction, sexuality, fertility, and professional practices are regulated socially. Such projects may target technical practices, but access to care is greatly influenced by social norms and ethics. This paper shows how an empirical anthropology that investigates the social and technical interfaces of reproduction can contribute to improved global health. Copyright © 2016 Elsevier Ltd. All rights reserved.

A finite-element toolbox for the stationary Gross-Pitaevskii equation with rotation

NASA Astrophysics Data System (ADS)

Vergez, Guillaume; Danaila, Ionut; Auliac, Sylvain; Hecht, Frédéric

2016-12-01

We present a new numerical system using classical finite elements with mesh adaptivity for computing stationary solutions of the Gross-Pitaevskii equation. The programs are written as a toolbox for FreeFem++ (www.freefem.org), a free finite-element software available for all existing operating systems. This offers the advantage to hide all technical issues related to the implementation of the finite element method, allowing to easily code various numerical algorithms. Two robust and optimized numerical methods were implemented to minimize the Gross-Pitaevskii energy: a steepest descent method based on Sobolev gradients and a minimization algorithm based on the state-of-the-art optimization library Ipopt. For both methods, mesh adaptivity strategies are used to reduce the computational time and increase the local spatial accuracy when vortices are present. Different run cases are made available for 2D and 3D configurations of Bose-Einstein condensates in rotation. An optional graphical user interface is also provided, allowing to easily run predefined cases or with user-defined parameter files. We also provide several post-processing tools (like the identification of quantized vortices) that could help in extracting physical features from the simulations. The toolbox is extremely versatile and can be easily adapted to deal with different physical models.

Control Charts When the Observations Are Correlated.

DTIC Science & Technology

1987-05-01

l7 D-AiB6 388 CONTROL CHARTS WHEN THE OBSERVATIONS ARE CORRELATED(J) i/iPITTSBURGH UNIV PA CENTER FOR KULTIVARIATE ANALYSIS P R KRISHNAIAH ET AL MAY... Krishnaiah and B. Q. Miao F-49620-85-C-0008 S. PERFORMING ORGANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK AREA II WORK UNIT NUMBERS... Krishnaiah and B.Q. Miao Center for Multivariate Analysis University of Pittsburgh N DTIC E L 1Zk-, -I- OCT0 11987 Play 1987 Technical Report No. 87-09

A Dynamic Computer Model to Examine Selected Effects of 304XX Career Field Consolidation.

DTIC Science & Technology

1982-09-01

DEPARTMENT OF THE AIR FORCED AIR UNIVERSITY (ATC) -; AIR FORCE INSTITUTE OF TECHNOLOGY D" "-gil tio "-: -I- -.- hA-W ig tP ttro Air, .’ Force Bas...The contents of tihe document are technically accurate, and no sensitive item., detrimeatal Ideas, or deleteriqu information are contained...ADDRESS O. PNOGAM ELEMENT. PROJECT, TASKAPE • WOe,6U" NUMERmsacT Scho6l of Systems and Logistics .A W N. " Air Force Institute of Technology , WPAFB It

Toxic Chemicals in the Soil Environment. Volume 2. Interactions of Some Toxic Chemicals/Chemical Warfare Agents and Soils

DTIC Science & Technology

1985-06-01

ELEMENT. PROJECT, TASK U Oklahomar OK AREA A WORK UNIT NUMBERS and I-M-4657-10-D49 Technical Analysis & Info Office, DPG It. CONTROLLING OFFICE NAME AND...and fragmented. The data that were found resulted from research that showed evidence of a lack of understanding of the basic concepts of soil...organic matter after exhaus- tive extraction with polar and non -polar solvents." Rowever, these residues are not necessarily restricted to the organic

Environmental Assessment for the Construction of the United States Air Force Technical Application Center (AFTAC) on Patrick Air Force Base, Florida

DTIC Science & Technology

2009-12-01

GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S...AND ADDRESS(ES) 45 Civil Engineer Squadron (45 CES/CEVP),1224 Jupiter Street,Patrick AFB,FL,32925 8. PERFORMING ORGANIZATION REPORT NUMBER 9...Quality Requirements Law or Rule Permit/Action(s) Requirement Agency or Organization AFI 32-7086, Chapter 4 Minimize loss and conduct recovery

Information Systems as a Social Space: Collaborative Teaching of Social Literacies to Technical Students

ERIC Educational Resources Information Center

Kalil, Claudia; Monson, Jo; Nodoba, Gaontebale

2010-01-01

This article describes a successful experimental collaborative teaching project to deliver a short course to develop work-relevant social literacies in technical students. Heterogeneous work contexts require both students and educators to find ways to integrate thinking and practices across disciplines. Teaching social literacies to information…

Mind the Gap: Infilling Stiegler's Philosophico-Educational Approach to Social Innovation

ERIC Educational Resources Information Center

Reveley, James; Peters, Michael A.

2016-01-01

According to Bernard Stiegler, social innovations in the educational field are an antidotical cure for social pathologies wrought by the digitalisation of society. This article explores how Stiegler's social pharmacology links to the human-technical co-constitution thesis that he first expounded in "Technics and Time, 1." Not only do we…

A Phenomenological Study of International Students in a Florida University Ph.D. Program

ERIC Educational Resources Information Center

Moffett, David W.

2006-01-01

Shifts in demographics of the international graduate student population in the United States since 2002 suggest universities should analyze and evaluate the academic, social, and cultural elements of their doctoral programs, to ensure students from previously underrepresented global regions experience needed adjustment support. The Investigator…

Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements B1: Education. Technical Report 49B1

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2009

2009-01-01

This technical paper contains information about the variables in the LSAY (Longitudinal Surveys of Australian Youth) Y95 cohort data set. It groups each variable into data elements which identifies common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant.…

Technical Elements of Transportation. Grade 11-12. Course #8176 (Semester). Technology Education Course Guide. Industrial Arts/Technology Education.

ERIC Educational Resources Information Center

North Carolina State Dept. of Public Instruction, Raleigh. Div. of Vocational Education.

This guide is intended for use in teaching a course in the history of the development of transportation systems and the individual elements in such systems. The course is designed to break transportation systems down into their individual components so as to make it possible to study system types, media, technical elements, and environmental…

Devising a consensus definition and framework for non-technical skills in healthcare to support educational design: A modified Delphi study.

PubMed

Gordon, Morris; Baker, Paul; Catchpole, Ken; Darbyshire, Daniel; Schocken, Dawn

2015-01-01

Non-technical skills are a subset of human factors that focus on the individual and promote safety through teamwork and awareness. There is no widely adopted competency- or outcome-based framework for non-technical skills training in healthcare. The authors set out to devise such a framework using a modified Delphi approach. An exhaustive list of published and team suggested items was presented to the expert panel for ranking and to propose a definition. In the second round, a focused list was presented, as well as the proposed definition elements. The finalised framework was sent to the panel for review. Sixteen experts participated. The final framework consists of 16 competencies for all and eight specific competencies for team leaders. The consensus definition describes non-technical skills as "a set of social (communication and team work) and cognitive (analytical and personal behaviour) skills that support high quality, safe, effective and efficient inter-professional care within the complex healthcare system". The authors have produced a new competency framework, through the works of an International expert panel, which is not discipline specific that can be used by curriculum developers, educational innovators and clinical teachers to support developments in the field.

The strategic relevance of manufacturing technology: An overall quality concept to promote innovation preventing drug shortage.

PubMed

Panzitta, Michele; Ponti, Mauro; Bruno, Giorgio; Cois, Giancarlo; D'Arpino, Alessandro; Minghetti, Paola; Mendicino, Francesca Romana; Perioli, Luana; Ricci, Maurizio

2017-01-10

Manufacturing is the bridge between research and patient: without product, there is no clinical outcome. Shortage has a variety of causes, in this paper we analyse only causes related to manufacturing technology and we use shortage as a paradigm highliting the relevance of Pharmaceutical Technology. Product and process complexity and capacity issues are the main challenge for the Pharmaceutical Industry Supply chain. Manufacturing Technology should be acknowledged as a R&D step and as a very important matter during University degree in Pharmacy and related disciplines, promoting collaboration between Academia and Industry, measured during HTA step and rewarded in terms of price and reimbursement. The above elements are not yet properly recognised, and manufacturing technology is taken in to consideration only when a shortage is in place. In a previous work, Panzitta et al. proposed to perform a full technology assessment at the Health Technological Assessment stage, evaluating three main technical aspects of a medicine: manufacturing process, physicochemical properties, and formulation characteristics. In this paper, we develop the concept of manufacturing appraisal, providing a technical overview of upcoming challenges, a risk based approach and an economic picture of shortage costs. We develop also an overall quality concept, not limited to GMP factors but broaden to all elements leading to a robust supply and promoting technical innovation. Copyright © 2016 Elsevier B.V. All rights reserved.

The Colombian nuclear scenario: Challenges and opportunities

NASA Astrophysics Data System (ADS)

Martinez, Isabel

2016-07-01

In Colombia, the absence of nuclear-oriented policies based on technical knowledge, the closing of the Nuclear Affairs Institute (1956-1998), the association of the word "nuclear" with weapons, plus the country's last six decades of internal conflict and narcotraffic have discourage the technical, social and environmental nuclear advance. However, there are technical, social and economic national challenges that could be faced by the present nuclear technical capacities.

Use of High Fidelity Methods in Multidisciplinary Optimization-A Preliminary Survey

NASA Technical Reports Server (NTRS)

Guruswamy, Guru P.; Kwak, Dochan (Technical Monitor)

2002-01-01

Multidisciplinary optimization is a key element of design process. To date multidiscipline optimization methods that use low fidelity methods are well advanced. Optimization methods based on simple linear aerodynamic equations and plate structural equations have been applied to complex aerospace configurations. However, use of high fidelity methods such as the Euler/ Navier-Stokes for fluids and 3-D (three dimensional) finite elements for structures has begun recently. As an activity of Multidiscipline Design Optimization Technical Committee (MDO TC) of AIAA (American Institute of Aeronautics and Astronautics), an effort was initiated to assess the status of the use of high fidelity methods in multidisciplinary optimization. Contributions were solicited through the members MDO TC committee. This paper provides a summary of that survey.

IFLA General Conference 1988. Division of Special Libraries. Section on Science and Technology Libraries; Section on Art Libraries; Section on Social Science Libraries; Section on Geography and Map Libraries; Division of Contributed Papers.

ERIC Educational Resources Information Center

International Federation of Library Associations, The Hague (Netherlands).

The 23 papers in this collection include papers on special libraries and miscellaneous contributed papers: (1) "Networking Potentialities and Limitations--Special Library Networks in Socialist Countries--An Overview, and the Main Ways of Perestroika in the Work of Scientific and Technical Libraries at the Present Stage" (D. Schmidmaier…

Impact of Technological and Structural Change on Employment. Prospective Analysis 2020. Synthesis Report. Report to the Committee on Employment and Social Affairs of the European Parliament. Technical Report Series.

ERIC Educational Resources Information Center

2001

The possible impact of technological and structural change on employment in the European Union (EU) over the next 20 years was examined through an exploration of the following alternative policy-driven scenarios: (1) business as usual; (2) concentrated technology policy (increases in innovation and research and development [R&D] efforts are…

Implementation Plan for Qualification of Sodium-Cooled Fast Reactor Technology Information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moe, Wayne; Honma, George

This document identifies and discusses implementation elements that can be used to facilitate consistent and systematic evaluation processes relating to quality attributes of technical information (with focus on SFR technology) that will be used to support licensing of advanced reactor designs. Information may include, but is not limited to, design documents for SFRs, research-and-development (R&D) data and associated documents, test plans and associated protocols, operations and test data, international research data, technical reports, and information associated with past U.S. Nuclear Regulatory Commission (NRC) reviews of SFR designs. The approach for determining acceptability of test data, analysis, and/or other technical informationmore » is based on guidance provided in INL/EXT-15-35805, “Guidance on Evaluating Historic Technology Information for Use in Advanced Reactor Licensing.” The implementation plan can be adopted into a working procedure at each of the national laboratories performing data qualification, or by applicants seeking future license application for advanced reactor technology.« less

The VOICES/VOCES success story: effective strategies for training, technical assistance and community-based organization implementation.

PubMed

Hamdallah, Myriam; Vargo, Sue; Herrera, Jennifer

2006-08-01

The Centers for Disease Control and Prevention's Diffusion of Effective Behavioral Interventions (DEBI) project successfully disseminated VOICES/VOCES, a brief video-based HIV risk reduction intervention targeting African American and Latino heterosexual men and women at risk for HIV infection. Elements of the dissemination strategy included a comprehensive and user-friendly intervention kit, comprising (a) an implementationmanual and othermaterials necessary for conducting the intervention (b) a Training of Facilitators (TOF) curriculum used to teach agency staff how to implement the EBI in their setting, (c) a network of expert trainers who attend a training institute to become adept at using the TOF curriculum to train facilitators, (d) a comprehensive training coordination center to plan and deliver TOF trainings, (e) proactive technical assistance to trainers, and (f) post-TOF technical assistance for local implementers. This article reports on those strategies and a local CBO's successful participation in DEBI, resulting implementation of VOICES/VOCES, with unique approaches to adaptation and tailoring.

Liver CT image processing: a short introduction of the technical elements.

PubMed

Masutani, Y; Uozumi, K; Akahane, Masaaki; Ohtomo, Kuni

2006-05-01

In this paper, we describe the technical aspects of image analysis for liver diagnosis and treatment, including the state-of-the-art of liver image analysis and its applications. After discussion on modalities for liver image analysis, various technical elements for liver image analysis such as registration, segmentation, modeling, and computer-assisted detection are covered with examples performed with clinical data sets. Perspective in the imaging technologies is also reviewed and discussed.

Spectral-element Method for 3D Marine Controlled-source EM Modeling

NASA Astrophysics Data System (ADS)

Liu, L.; Yin, C.; Zhang, B., Sr.; Liu, Y.; Qiu, C.; Huang, X.; Zhu, J.

2017-12-01

As one of the predrill reservoir appraisal methods, marine controlled-source EM (MCSEM) has been widely used in mapping oil reservoirs to reduce risk of deep water exploration. With the technical development of MCSEM, the need for improved forward modeling tools has become evident. We introduce in this paper spectral element method (SEM) for 3D MCSEM modeling. It combines the flexibility of finite-element and high accuracy of spectral method. We use Galerkin weighted residual method to discretize the vector Helmholtz equation, where the curl-conforming Gauss-Lobatto-Chebyshev (GLC) polynomials are chosen as vector basis functions. As a kind of high-order complete orthogonal polynomials, the GLC have the characteristic of exponential convergence. This helps derive the matrix elements analytically and improves the modeling accuracy. Numerical 1D models using SEM with different orders show that SEM method delivers accurate results. With increasing SEM orders, the modeling accuracy improves largely. Further we compare our SEM with finite-difference (FD) method for a 3D reservoir model (Figure 1). The results show that SEM method is more effective than FD method. Only when the mesh is fine enough, can FD achieve the same accuracy of SEM. Therefore, to obtain the same precision, SEM greatly reduces the degrees of freedom and cost. Numerical experiments with different models (not shown here) demonstrate that SEM is an efficient and effective tool for MSCEM modeling that has significant advantages over traditional numerical methods.This research is supported by Key Program of National Natural Science Foundation of China (41530320), China Natural Science Foundation for Young Scientists (41404093), and Key National Research Project of China (2016YFC0303100, 2017YFC0601900).

Fusing Social Media and Mobile Analytics for Urban Sense-Making

DTIC Science & Technology

2017-05-09

AFRL-AFOSR-JP-TR-2017-0037 Fusing Social Media and Mobile Analytics for Urban Sense-Making Archan Misra SINGAPORE MANAGEMENT UNIVERSITY Final Report...CONTRACT NUMBER 5b.  GRANT NUMBER FA2386-14-1-0002 5c.  PROGRAM ELEMENT NUMBER 61102F 6. AUTHOR(S) Archan Misra 5d.   PROJECT NUMBER 5e.  TASK...NUMBER 5f.  WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) SINGAPORE MANAGEMENT UNIVERSITY 81 VICTORIA STREET SINGAPORE, 188065 SG 8

A Randomized, Controlled Trial of Intranasal Oxytocin as an Adjunct to Behavioral Therapy for Autism Spectrum Disorder

DTIC Science & Technology

2016-10-01

AWARD NUMBER: W81XWH-12-1-0543 TITLE: A Randomized, Controlled Trial of Intranasal Oxytocin as an Adjunct to Behavioral Therapy for Autism ...Therapy for Autism Spectrum Disorder 5b. GRANT NUMBER W81XWH-12-1-0543 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) John Gabrieli, Ph.D; Aude Henin...core social dysfunctions, and (2) oxytocin (OT) administration prior to CBT sessions will each enhance social function in young adults with autism

French Army - Family Psychological and Social Support

DTIC Science & Technology

2006-04-01

Major de l’armée de Terre, Bureau condition du personnel 14 rue Saint-Dominique 00453 Armées FRANCE The French Army is permanently engaged on...ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) French Army...RTO-MP-HFM-134 21E - 1 French Army – Family Psychological and Social Support LCL G. BOUILLAUD French Army Staff, Quality Of Life Etat

A change in social activity and depression among Koreans aged 45 years and more: analysis of the Korean Longitudinal Study of Aging (2006-2010).

PubMed

Choi, Young; Park, Eun-Cheol; Kim, Jae-Hyun; Yoo, Ki-Bong; Choi, Jae-Woo; Lee, Kwang-Sig

2015-04-01

The aim of this study is to examine a relationship between a change in social activity and depression among Koreans aged 45 years or more. Data came from the Korean Longitudinal Study of Aging (KLoSA) (2006-2010), with 5,327 participants aged 45 years or more. The generalized estimating equation (GEE) with the logit link was used to investigate an association between a change in social activity during 2006-2008 (or 2008-2010) and depression among respondents in year 2008 (or Y2010). Depression was measured by Center for Epidemiological Studies Depression scale (CES-D10) and a change in social activity was classified with four categories, i.e. "consistent participation", "consistent non-participation", "participation to non-participation", and "non-participation to participation". Social activity was divided into various elements and the same analysis was conducted for each of these elements. Those with consistent non-participation and from participation to non-participation were more likely to be depressed than those with consistent participation and from non-participation to participation in social activities (OR 1.44 [95% CI 1.22-1.71], OR 1.35 [95% CI 1.15-1.58] vs. OR 1.00 [Reference], OR 1.27 [95% CI 1.09-1.48]). In addition, the strength of the negative association between consistent or new participation in social activity and depression was different across different elements of social activity. The negative association was particularly strong for leisure, culture or sports clubs, and for family or school reunion. For improving the mental health of the population aged 45 years or more, the promotion of their continued or new participations in leisure/culture clubs and family/school reunion might be needed in South Korea.

3D animation in three dimensions: the rocky road to the obvious

NASA Astrophysics Data System (ADS)

Murray, Hugh

2006-02-01

That animation created using CG modeling and animation tools is inherently three-dimensional is well known. In the middle to late nineties IMAX Corporation began actively exploring CG animated features as a possible source of economically viable content for its rapidly growing network of stereoscopic IMAX® 3D theatres. The journey from there to the spectacular success of the IMAX® 3D version of The Polar Express is an interesting mix of technical, creative and production challenges. For example 3D animations often have 2D elements and include many sequences that have framing, composition and lens choices that a stereographer would have avoided had 3D been part of the recipe at the outset. And of course the decision to ask for a second set of deliverables from an already stressed production takes nerve. The talk will cover several of these issues and explain why the unique viewing experience enabled by the wideangle geometry of IMAX® 3D theatres makes it worth all the pain.

Function follows form: combining nanoimprint and inkjet printing

NASA Astrophysics Data System (ADS)

Muehlberger, M.; Haslinger, M. J.; Kurzmann, J.; Ikeda, M.; Fuchsbauer, A.; Faury, T.; Koepplmayr, T.; Ausserhuber, H.; Kastner, J.; Woegerer, C.; Fechtig, D.

2017-06-01

We are investigating the possibilities and the technical requirements to do nanopatterning on arbitrary curved surfaces. This is done considering the opportunities and possibilities of additive manufacturing. One of the key elements is the necessity to deposit material in well-defined areas of various complex 3D objects. In order to achieve this we are developing a robot-based inkjet printing. We report on our progress with this respect and also on our efforts to perform nanoimprinting on curved, possibly 3D-printed objects using materials that can be deposited by inkjet printing. In the framework of this article, we provide an overview over our current status, the challenges and an outlook.

Experimental quantum information processing with the Talbot effect

NASA Astrophysics Data System (ADS)

Sawada, K.; Walborn, S. P.

2018-07-01

We report a proof of concept experiment illustrating the implementation of several simple quantum logic gates on D-level quantum systems (quDits) using the Talbot effect. A number of QuDit states are encoded into the transverse profile of a paraxial laser beam using a spatial light modulator. These states are transformed through a diagonal phase element and then free-propagation via the fractional Talbot effect, demonstrating the realization of some well-known single quDit gates in quantum computation. Our classical optics experiment allows us to identify several important technical details, and serves as a first experimental step in performing D-dimensional quantum operations with single photons or other quantum systems using this scheme.

Determinants of sustainability in solid waste management - The Gianyar Waste Recovery Project in Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zurbruegg, Christian, E-mail: zurbrugg@eawag.ch; Gfrerer, Margareth, E-mail: margareth.gfrerer@gmx.net; Ashadi, Henki, E-mail: henki@eng.ui.ac.id

2012-11-15

Highlights: Black-Right-Pointing-Pointer Our assessment tool helps evaluate success factors in solid waste projects. Black-Right-Pointing-Pointer Success of the composting plant in Indonesia is linked to its community integration. Black-Right-Pointing-Pointer Appropriate technology is not a main determining success factor for sustainability. Black-Right-Pointing-Pointer Structured assessment of 'best practices' can enhance replication in other cities. - Abstract: According to most experts, integrated and sustainable solid waste management should not only be given top priority, but must go beyond technical aspects to include various key elements of sustainability to ensure success of any solid waste project. Aside from project sustainable impacts, the overall enabling environmentmore » is the key feature determining performance and success of an integrated and affordable solid waste system. This paper describes a project-specific approach to assess typical success or failure factors. A questionnaire-based assessment method covers issues of: (i) social mobilisation and acceptance (social element), (ii) stakeholder, legal and institutional arrangements comprising roles, responsibilities and management functions (institutional element); (iii) financial and operational requirements, as well as cost recovery mechanisms (economic element). The Gianyar Waste Recovery Project in Bali, Indonesia was analysed using this integrated assessment method. The results clearly identified chief characteristics, key factors to consider when planning country wide replication but also major barriers and obstacles which must be overcome to ensure project sustainability. The Gianyar project consists of a composting unit processing 60 tons of municipal waste per day from 500,000 inhabitants, including manual waste segregation and subsequent composting of the biodegradable organic fraction.« less

Technological innovation, human capital and social change for sustainability. Lessons learnt from the industrial technologies theme of the EU's Research Framework Programme.

PubMed

Sabadie, Jesús Alquézar

2014-05-15

Europe is facing a twofold challenge. It must maintain or even increase its competitiveness, a basic requirement in a globalised economy and under the current demographic threat. It needs also to tackle the so-called "grand challenges", especially environmental issues, through a sustainable model of production and consumption. Such challenges should lead to new business and industrial models, based on more sustainable production and consumption chains, from design to end of life. This implies a need for new industrial materials and processes, new skills and, indeed, new values and life-styles. Sustainability and innovation are key elements of EU's Research and Innovation Framework Programmes, particularly in the field of industrial technologies (nanotechnologies, materials and industrial technologies), which objective is to "improve the competitiveness of the European industry and generate knowledge to ensure its transformation from a resource intensive to a knowledge intensive industry". Sustainability and innovation are interrelated challenges for R&D. Research can develop technical solutions to tackle environmental or societal challenges, but such technologies need to be successfully commercialised to have a real environmental impact. Several socio-economic studies carried-out by the European Commission show not only the emerging technological and industrial trends, but they also emphasise the need for linking sustainable technologies with social change. Human capital and new social behaviours are critical factors to combine economic competitiveness and sustainability: technology alone is no longer able to solve global challenges. But what kind of human capital (skills, behaviours, and values) are we referring to? How to encourage the shift towards a greener society through human capital? Which reforms are needed in education systems to move towards a sustainable economy? Are there examples of social innovation to be extrapolated and/or generalised? © 2013 Elsevier B.V. All rights reserved.

a 3d Based Approach to the Architectural Study of the Roman Bath at the Sanctuary of Apollo Hylates (kourion, Cyprus).

NASA Astrophysics Data System (ADS)

Faka, M.; Christodoulou, S.; Abate, D.; Ioannou, C.; Hermon, S.

2017-08-01

Roman baths represented a popular social practice of everyday life, cited in numerous literary sources and testified by ample archaeological remains all over the Roman Empire. Although regional studies have contributed extensively to our knowledge about how baths functioned and what was their social role in various regions of the Mediterranean, their study in Cyprus is yet to be developed. Moreover, despite the increasing availability of devices and techniques for 3D documentation, various characteristics, especially in relation to the heating and water supply system of the baths, were omitted and were not properly and accurately documented. The pilot case study outlined in this paper presents the 3D documentation of the Roman bath, excavated in the 1950s, within the area of the Sanctuary of Apollo Hylates at Kourion (Limassol district). The creation of an accurate 3D model of the documented area through image and range based techniques combined with topographic data, allows the detailed analysis of architectural elements and their decorative features. At the same time, it enables accurate measurements of the site, which are used as input for the archaeological interpretation and virtual reconstruction of the original shape of the bath. In addition, this project aims to answer a number of archaeological research questions related to Roman baths such as their architectural features, function mode, and technological elements related to heating techniques.

Technical Information Resource on Rare Earth Elements Now Available to Public and Private Sector Stakeholders

EPA Science Inventory

A new EPA technical information resource, “Rare Earth Elements: A Review of Production, Processing, Recycling, and Associated Environmental Issues” has been produced as an introductory resource for those interested in learning more about REE mining and alternatives to meet demand...

Trusses Of Tensegrity Type In A Concept Of Train Station Renovation In Żary

NASA Astrophysics Data System (ADS)

Lechocka, Paulina

2015-09-01

The first railway station in Żary was built in 1843 in Germany. After the Second World War and years of socialism in Poland the meaning of railway decreased and its technical condition deteriorated. Now the building needs renovation and change of function. Tensegrity structures may be useful in renovation of platforms shelter. They are strut and tie construction, in which there is self-stabilization between compressed and tensioned elements. Conception of new platform shelter is based on exemplary tensegrity module consist of three struts and nine cables (called "Simplex"). Tensegrity would make railway station more modern, but not cover its original elevation.

Space Station needs, attributes and architectural options: Summary briefing

NASA Technical Reports Server (NTRS)

1983-01-01

Computerized data sorting and analysis techniques were used with a data base accumulated in over 20 years of space station studies to evaluate candidate missions and select a final model of 88 missions. The social, cultural, scientific, technical, and commercial benefits to be accrued from each mission were identified. Requirements were determined for satellite servicing; payload placement and retrieval; refueling; repair; testing; assembly; and construction. Missions drivers determined include crew, remote manipulating system, external parts, instrumentation, extravehicular activity/manned maneuvering unit, and voice/video equipment. User interest for commercial applications were determined. Variable architecture based on a modular concept with multi-use elements is proposed.

76 FR 16531 - Technical Correction for Neurological Listing Cross-Reference

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-24

... 1-800-325-0778, or visit our Internet site, Social Security Online, at http://www.socialsecurity.gov... SOCIAL SECURITY ADMINISTRATION 20 CFR Part 404 [Docket No. SSA-2011-0019] RIN 0960-AH33 Technical Correction for Neurological Listing Cross-Reference AGENCY: Social Security Administration. ACTION: Final...

75 FR 33167 - Technical Amendment Language Change From “Wholly” to “Fully”

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-11

... SOCIAL SECURITY ADMINISTRATION 20 CFR Parts 404, 405, 408, 416, and 418 [Docket No. SSA-2009-0062] RIN 0960-AH16 Technical Amendment Language Change From ``Wholly'' to ``Fully'' AGENCY: Social Security... these final rules, call Brian J. Rudick, Office of Regulations, Social Security Administration, 6401...

Necessary organizational changes according to Burke-Litwin model in the head nurses system of management in healthcare and social welfare institutions - the Slovenia experience.

PubMed

Filej, Bojana; Skela-Savic, Brigita; Vicic, Visnja H; Hudorovic, Narcis

2009-05-01

To discover which changes should be implemented in the system of head nursing management in Slovenian healthcare institutions and social welfare institutions. The questionnaire was distributed to 155 head nurses of Slovenian hospitals, primary healthcare centres and social welfare institutions. The Burke-Litwin organizational change model has been used to look at which changes have to be implemented in the management system of head nurses. In hospitals head nurses have greater independent competence for planning professional training of nursing employees (p<.022) and are also more independent when it comes to selecting employees when it comes to new job openings (M=4.20, S.D.=.83, p<.004). According to the Burke-Litwin organizational change model, the elements to which changes should be introduced include "external environment" for primary healthcare centres and social welfare institutions, and "system (policies and procedures)" for primary healthcare centres. According to results of our study, changes are needed in leadership and management of nursing in primary healthcare centres. In social welfare institutions changes are only required in leadership. Organizational changes are not necessary for any element of the Burke-Litwin model for hospitals.

Organizational Effectiveness: Development and Validation of Integrated Models. Report II. Empirical Studies of Organizational Effectiveness Using Multivariate Models

DTIC Science & Technology

1982-04-01

34 ’Institute for Social Research LEADERSHIP AND MANAGEMENT TECHNICAL AREA DTIC ~EL ECT-ICI /AUG 2 1983 U. S. Army D C3 Research Institute for the Behavioral and...about or aIlowing changes within the organizatin itself (Georgopoulos, 1972; Georgopoulos & Tannenbaum, 1957). As open systems, organizations and their...in school organizations. Unpublished manuscript, The University of Michigan, 1980. Selznick, P. Leadership in administration. Evanston, Ill.: Row

Three-dimensional reconstruction of indoor whole elements based on mobile LiDAR point cloud data

NASA Astrophysics Data System (ADS)

Gong, Yuejian; Mao, Wenbo; Bi, Jiantao; Ji, Wei; He, Zhanjun

2014-11-01

Ground-based LiDAR is one of the most effective city modeling tools at present, which has been widely used for three-dimensional reconstruction of outdoor objects. However, as for indoor objects, there are some technical bottlenecks due to lack of GPS signal. In this paper, based on the high-precision indoor point cloud data which was obtained by LiDAR, an international advanced indoor mobile measuring equipment, high -precision model was fulfilled for all indoor ancillary facilities. The point cloud data we employed also contain color feature, which is extracted by fusion with CCD images. Thus, it has both space geometric feature and spectral information which can be used for constructing objects' surface and restoring color and texture of the geometric model. Based on Autodesk CAD platform and with help of PointSence plug, three-dimensional reconstruction of indoor whole elements was realized. Specifically, Pointools Edit Pro was adopted to edit the point cloud, then different types of indoor point cloud data was processed, including data format conversion, outline extracting and texture mapping of the point cloud model. Finally, three-dimensional visualization of the real-world indoor was completed. Experiment results showed that high-precision 3D point cloud data obtained by indoor mobile measuring equipment can be used for indoor whole elements' 3-d reconstruction and that methods proposed in this paper can efficiently realize the 3 -d construction of indoor whole elements. Moreover, the modeling precision could be controlled within 5 cm, which was proved to be a satisfactory result.

The Quantitative Analysis of User Behavior Online - Data, Models and Algorithms

NASA Astrophysics Data System (ADS)

Raghavan, Prabhakar

By blending principles from mechanism design, algorithms, machine learning and massive distributed computing, the search industry has become good at optimizing monetization on sound scientific principles. This represents a successful and growing partnership between computer science and microeconomics. When it comes to understanding how online users respond to the content and experiences presented to them, we have more of a lacuna in the collaboration between computer science and certain social sciences. We will use a concrete technical example from image search results presentation, developing in the process some algorithmic and machine learning problems of interest in their own right. We then use this example to motivate the kinds of studies that need to grow between computer science and the social sciences; a critical element of this is the need to blend large-scale data analysis with smaller-scale eye-tracking and "individualized" lab studies.

Geological Disposal of Radioactive Waste: A Long-Term Socio-Technical Experiment.

PubMed

Schröder, Jantine

2016-06-01

In this article we investigate whether long-term radioactive waste management by means of geological disposal can be understood as a social experiment. Geological disposal is a rather particular technology in the way it deals with the analytical and ethical complexities implied by the idea of technological innovation as social experimentation, because it is presented as a technology that ultimately functions without human involvement. We argue that, even when the long term function of the 'social' is foreseen to be restricted to safeguarding the functioning of the 'technical', geological disposal is still a social experiment. In order to better understand this argument and explore how it could be addressed, we elaborate the idea of social experimentation with the notion of co-production and the analytical tools of delegation, prescription and network as developed by actor-network theory. In doing so we emphasize that geological disposal inherently involves relations between surface and subsurface, between humans and nonhumans, between the social, material and natural realm, and that these relations require recognition and further elaboration. In other words, we argue that geological disposal concurrently is a social and a technical experiment, or better, a long-term socio-technical experiment. We end with proposing the idea of 'actor-networking' as a sensitizing concept for future research into what geological disposal as a socio-technical experiment could look like.

A comparison of a technical and a participatory application of social impact assessment.

Treesearch

Dennis R Becker; Charles C Harris; Erik A Nielsen; William J. McLaughlin

2004-01-01

Results of independent applications of a technical and a participatory approach to SIA are compared for an assessment of impacts of the proposed removal of hydroelectric dams to recover threatened and endangered salmon in the Pacific Northwest of the United States. The analysis focuses on empirical differences and similarities between the technical social analysis...

STP 4-06 Model-Based Technical Data in Procurement, 3D PDF Technology Data Demonstration Project. Phase 1 Summary

DTIC Science & Technology

2015-07-01

O R G STP 4-06 MODEL-BASED TECHNICAL DATA IN PROCUREMENT 3D PDF TECHNOLOGY DATA DEMONSTRATION PROJECT PHASE 1 SUMMARY REPORT DL309T2...LMI’s ISO- certified quality management procedures. J U L Y 2 0 1 5 STP 4-06 MODEL-BASED TECHNICAL DATA IN PROCUREMENT 3D PDF TECHNICAL DATA...Based Technical Data ..................................................................................... 5 3D PDF Demonstration Team

Selfish DNA: a pharmaceutical perspective.

PubMed

Winckler, T

2013-07-01

Almost 25 years ago, Theo Dingermann published the discovery of a new mobile genetic element in the unicellular microbe Dictyostelium discoideum in the journal Science. An interesting property of this new molecular parasite, the Dictyostelium Repetitive Element (DRE), was that all integrations were found approximately 50 base pairs (bp) upstream of transfer RNA (tRNA) genes in the D. discoideum genome, thus implying an active targeting mechanism to avoid the disruption of host cell genes by the retrotransposition process. Since then, the facultative multicellular "social amoeba" D. discoideum has become a popular model for analyzing complex cellular functions such as cell movement, chemotaxis, phagocytosis, and cell differentiation, important areas of biomedical research that are often hard to investigate in cells from "higher organisms" including humans. Therefore, progress in the development of methods to study Dictyostelium biology has also provoked research on transposable elements in this organism. Early work on the DRE element suggested that studying its molecular mechanism of site-specific integration might promote human gene therapy technology through the design of integrating gene transfer vectors with low intrinsic genotoxic potential. In this review article, I will briefly review the original research performed on the DRE transposable element in the Dingermann lab and report on how the emergence of genomics technologies and the development of tools to analyze de novo retrotransposition events in D. discoideum cells will expand our knowledge of DRE biology in the future.

Self-compacting concrete for prestressed bridge girders

NASA Astrophysics Data System (ADS)

Erkmen, Bulent

The purpose of this study was to examine social mobility as a motivation for first-generation college students in reaching attainment at two-year technical colleges. The research question was to what degree has the perception of social mobility influenced first generation college students at technical colleges to complete their career educational goals. Graduates of a two-year technical college were asked a series of open-ended questions regarding their past experiences and perceptions of attending and completing a two-year technical college program; their childhood perceptions of their social status; and experiences with family members regarding their change in social class status. These questions were designed to determine their feelings, viewpoints, reflections, experiences, struggles, and thoughts about attainment (completing their post-secondary education) and the extent to which social mobility influenced their decision to complete their education. The benefits of this research include an understanding of social mobility and educational attainment. Results of this study could be used to better understand the process that first generation college students go through in order to attain their educational goals. The information from this study may be useful for technical college administrations to help design programs and processes for future first-generation college students' success and aid in retention of these students.

THE ROLE OF AQUEOUS THIN FILM EVAPORATIVE COOLING ON RATES OF ELEMENTAL MERCURY AIR-WATER EXCHANGE UNDER TEMPERATURE DISEQUILIBRIUM CONDITIONS

EPA Science Inventory

The technical conununity has only recently addressed the role of atmospheric temperature variations on rates of air-water vapor phase toxicant exchange. The technical literature has documented that: 1) day time rates of elemental mercury vapor phase air-water exchange can exceed ...

An Object-Oriented Architecture for Intelligent Tutoring Systems. Technical Report No. LSP-3.

ERIC Educational Resources Information Center

Bonar, Jeffrey; And Others

This technical report describes a generic architecture for building intelligent tutoring systems which is developed around objects that represent the knowledge elements to be taught by the tutor. Each of these knowledge elements, called "bites," inherits both a knowledge organization describing the kind of knowledge represented and…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diaz, Aaron A.; Chamberlin, Clyde E.; Edwards, Matthew K.

This section of the Joint summary technical letter report (TLR) describes work conducted at the Pacific Northwest National Laboratory (PNNL) during FY 2016 (FY16) on the under-sodium viewing (USV) PNNL project 58745, work package AT-16PN230102. This section of the TLR satisfies PNNL’s M3AT-16PN2301025 milestone and is focused on summarizing the design, development, and evaluation of two different phased-array ultrasonic testing (PA-UT) probe designs—a two-dimensional (2D) matrix phased-array probe, and two one-dimensional (1D) linear array probes, referred to as serial number 4 (SN4) engineering test units (ETUs). The 2D probe is a pulse-echo (PE), 32×2, 64-element matrix phased-array ETU. The 1Dmore » probes are 32×1 element linear array ETUs. This TLR also provides the results from a performance demonstration (PD) of in-sodium target detection trials at 260°C using both probe designs. This effort continues the iterative evolution supporting the longer term goal of producing and demonstrating a pre-manufacturing prototype ultrasonic probe that possesses the fundamental performance characteristics necessary to enable the development of a high-temperature sodium-cooled fast reactor (SFR) inspection system for in-sodium detection and imaging.« less

77 FR 52698 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-30

... training equipment, publications and technical data, U.S. Government and contractor technical and logistics personnel services and other related elements of program and logistics support. (iv) Military Department..., publications and technical data, U.S. Government and contractor technical and logistics personnel services and...

Social and ethical perspectives of landslide risk mitigation measures

NASA Astrophysics Data System (ADS)

Kalsnes, Bjørn; Vangelsten, Bjørn V.

2015-04-01

Landslide risk may be mitigated by use of a wide range of measures. Mitigation and prevention options may include (1) structural measures to reduce the frequency, severity or exposure to the hazard, (2) non-structural measures, such as land-use planning and early warning systems, to reduce the hazard frequency and consequences, and (3) measures to pool and transfer the risks. In a given situation the appropriate system of mitigation measures may be a combination of various types of measures, both structural and non-structural. In the process of choosing mitigation measures for a given landslide risk situation, the role of the geoscientist is normally to propose possible mitigation measures on basis of the risk level and technical feasibility. Social and ethical perspectives are often neglected in this process. However, awareness of the need to consider social as well as ethical issues in the design and management of mitigating landslide risk is rising. There is a growing understanding that technical experts acting alone cannot determine what will be considered the appropriate set of mitigation and prevention measures. Issues such as environment versus development, questions of acceptable risk, who bears the risks and benefits, and who makes the decisions, also need to be addressed. Policymakers and stakeholders engaged in solving environmental risk problems are increasingly recognising that traditional expert-based decision-making processes are insufficient. This paper analyse the process of choosing appropriate mitigation measures to mitigate landslide risk from a social and ethical perspective, considering technical, cultural, economical, environmental and political elements. The paper focus on stakeholder involvement in the decision making process, and shows how making strategies for risk communication is a key for a successful process. The study is supported by case study examples from Norway and Italy. In the Italian case study, three different risk mitigation options was presented to the local community. The options were based on a thorough stakeholder involvement process ending up in three different views on how to deal with the landslide risk situation: i) protect lives and properties (hierarchical) ; ii) careful stewardship of the mountains (egalitarian); and iii) rational individual choice (individualist).

36 CFR Appendix D to Part 1191 - Technical

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Technical D Appendix D to Part 1191 Parks, Forests, and Public Property ARCHITECTURAL AND TRANSPORTATION BARRIERS COMPLIANCE...; ARCHITECTURAL BARRIERS ACT (ABA) ACCESSIBILITY GUIDELINES Pt. 1191, App. D Appendix D to Part 1191—Technical...

Human Rights and the Global Fund to Fight AIDS, Tuberculosis and Malaria

PubMed Central

Jürgens, Ralf; Lim, Hyeyoung; Timberlake, Susan; Smith, Matthew

2017-01-01

Abstract The Global Fund to Fight AIDS, Tuberculosis and Malaria was created to greatly expand access to basic services to address the three diseases in its name. From its beginnings, its governance embodied some human rights principles: civil society is represented on its board, and the country coordination mechanisms that oversee funding requests to the Global Fund include representatives of people affected by the diseases. The Global Fund’s core strategies recognize that the health services it supports would not be effective or cost-effective without efforts to reduce human rights-related barriers to access and utilization of health services, particularly those faced by socially marginalized and criminalized persons. Basic human rights elements were written into Global Fund grant agreements, and various technical support measures encouraged the inclusion in funding requests of programs to reduce human rights-related barriers. A five-year initiative to provide intensive technical and financial support for the scaling up of programs to reduce these barriers in 20 countries is ongoing. PMID:29302175

Theoretical approaches to creation of robotic coal mines based on the synthesis of simulation technologies

NASA Astrophysics Data System (ADS)

Fryanov, V. N.; Pavlova, L. D.; Temlyantsev, M. V.

2017-09-01

Methodological approaches to theoretical substantiation of the structure and parameters of robotic coal mines are outlined. The results of mathematical and numerical modeling revealed the features of manifestation of geomechanical and gas dynamic processes in the conditions of robotic mines. Technological solutions for the design and manufacture of technical means for robotic mine are adopted using the method of economic and mathematical modeling and in accordance with the current regulatory documents. For a comparative performance evaluation of technological schemes of traditional and robotic mines, methods of cognitive modeling and matrix search for subsystem elements in the synthesis of a complex geotechnological system are applied. It is substantiated that the process of technical re-equipment of a traditional mine with a phased transition to a robotic mine will reduce unit costs by almost 1.5 times with a significant social effect due to a reduction in the number of personnel engaged in hazardous work.

Leader Identity, Individual Differences, and Leader Self-Development

DTIC Science & Technology

2012-09-01

and Social Sciences Approved for public release; distribution is unlimited. U.S. Army Research Institute for the Behavioral and Social ... Social Sciences, Attn: DAPC-ARI-MS, 6000 6th Street, Fort Belvoir, VA 22060-5586. FINAL DISPOSITION: Destroy this Technical Report when it is no...longer needed. Do not return it to the U.S. Army Research Institute for the Behavioral and Social Sciences. NOTE: The findings in this Technical

Social media and nursing practice: changing the balance between the social and technical aspects of work.

PubMed

Casella, Evan; Mills, Jane; Usher, Kim

2014-01-01

Modern communication methods are drastically changing the way people interact with each other. Professions such as nursing need to evolve to remain relevant as social infrastructure changes. In the 1960s, researchers developed a sociotechnical theory that stated workers were more motivated and productive if there was a good balance between the social and technical aspects of their work. Today's technology is blurring the boundaries between the social and the technical thereby transforming human contact and communication into a multi-method process. In Australia, people are adept at utilising social media technology to become more efficient, creative and connected; Australian nurses also need to embrace changing technology to capitalise on the professional opportunities offered by social media. This paper imagines a world where nurses integrate social media into assessing, diagnosing, planning, implementing and evaluating care. Discussion draws on a combination of real-world examples of best-practice and blue-sky thinking to demonstrate that evidence-based care must be combined with the adoption of future-forward technology.

Thermionic fuel element for the S-prime reactor

NASA Astrophysics Data System (ADS)

Van Hagan, Thomas H.; Drees, Elizabeth A.

1993-01-01

Technical aspects of the thermionic fuel element (TFE) design proposed for the S-PRIME space nuclear power system are discussed. Topics covered include the rational for selecting a multicell TFE approach, a technical description of the S-PRIME TFE and its estimated performance, and the technology readiness of the design, which emphasizes techology maturity and low risk.

Social Science Research Institutes in the Quality American University. Final Technical Report.

ERIC Educational Resources Information Center

Totman, Theodore L.

The technical report presents a chapter outline and thesis summary of an investigation of social science research institutes in American universities. The bulk of the report presents the thesis in four sections. Section I proposes a typology of organized social research units (OSRUs) in the 11 universities studied. Dimensions used to classify the…

Technical intelligence and culture: Nut cracking in humans and chimpanzees.

PubMed

Boesch, Christophe; Bombjaková, Daša; Boyette, Adam; Meier, Amelia

2017-06-01

According to the technical intelligence hypothesis, humans are superior to all other animal species in understanding and using tools. However, the vast majority of comparative studies between humans and chimpanzees, both proficient tool users, have not controlled for the effects of age, prior knowledge, past experience, rearing conditions, or differences in experimental procedures. We tested whether humans are superior to chimpanzees in selecting better tools, using them more dexteriously, achieving higher performance and gaining access to more resource as predicted under the technical intelligence hypothesis. Aka and Mbendjele hunter-gatherers in the rainforest of Central African Republic and the Republic of Congo, respectively, and Taï chimpanzees in the rainforest of Côte d'Ivoire were observed cracking hard Panda oleosa nuts with different tools, as well as the soft Coula edulis and Elaeis guinensis nuts. The nut-cracking techniques, hammer material selection and two efficiency measures were compared. As predicted, the Aka and the Mbendjele were able to exploit more species of hard nuts in the forest than chimpanzees. However, the chimpanzees were sometimes more efficient than the humans. Social roles differed between the two species, with the Aka and especially the Mbendjele exhibiting cooperation between nut-crackers whereas the chimpanzees were mainly individualistic. Observations of nut-cracking by humans and chimpanzees only partially supported the technical intelligence hypothesis as higher degrees of flexibility in tool selection seen in chimpanzees compensated for use of less efficient tool material than in humans. Nut cracking was a stronger social undertaking in humans than in chimpanzees. © 2017 Wiley Periodicals, Inc.

Blocking of Person Information in Small Social Groupings: The Information of Person Categories.

DTIC Science & Technology

1983-12-20

Anderson, R . C ., & Watts, G. H. Bidirectional associations in multi-trial free recall. Psychonomic Science, 1969, 15, 288-9. Asch, S. E . Forming...categories Technical Report s. PERFORMING ORG. REPORT NUMBER _RF 762498/713444 7. AUTHOR( e ) S. CONTRACT ON GRANT NUMER(.) C . D. McCann, T.M. Ostrom, M.L...the structure of person impressions unless it has been cognitively organized along with the [ ’ e ~v’-’ ,,’ ’ ’ ¢J . J,’,,’ ’ ? : _ 7, ’ r

[Indicators, variables and obstacles to the life cycle of scientific and technical information in health. Experiences of the Centro Nacional de Información y Documentación en Salud in Mexico].

PubMed

Macías-Chapula, C A

1987-01-01

Indicators, variables and barriers to scientific and technical health information have been detected and described by CENIDS in Mexico within the life cycle of the information production model, covering the phases of: a) generation; b) institutionalization; c) maintenance/development; and d) distribution/dissemination. Emphasis is placed on the important role that play social, economic, demographic, and political factors of each developing country to conform their ideal information life cycle. After an analysis of the existing Mexican situation, and a short description of CENIDS' structure, organization, functions and services, CENIDS' short-term and mid-term projects, and suggestions for further research lines to improve the current situation in Mexico are also given.

Establishing ecological and social continuities: new challenges to optimize urban watershed management

NASA Astrophysics Data System (ADS)

Mitroi, V.; de Coninck, A.; Vinçon-Leite, B.; Deroubaix, J.-F.

2014-09-01

The (re)construction of the ecological continuity is stated as one of the main objectives of the European Water Framework Directive for watershed management in Europe. Analysing the social, political, technical and scientific processes characterising the implementation of different projects of ecological continuity in two adjacent peri-urban territories in Ile-de-France, we observed science-driven approaches disregarding the social contexts. We show that, in urbanized areas, ecological continuity requires not only important technical and ecological expertise, but also social and political participation to the definition of a common vision and action plan. Being a challenge for both, technical water management institutions and "classical" ecological policies, we propose some social science contributions to deal with ecological unpredictability and reconsider stakeholder resistance to this kind of project.

[A network to promote health systems based on primary health care in the Region of the Americas].

PubMed

Herrera Vázquez, María Magdalena; Rodríguez Avila, Nuria; Nebot Adell, Carme; Montenegro, Hernán

2007-05-01

To identify the relational components of an international network of organizations that provide technical and financial assistance to promote the development of health systems based on primary health care in the countries of the Region of the Americas; to analyze the linkages that would allow the collaborating partners of the Pan American Health Organization (PAHO) to work together on health issues; and to determine the basic theoretical elements that can help to develop action strategies that support advocacy efforts by a network. This was a qualitative and quantitative cross-sectional study based on identifying key informants and on analyzing social networks. Ethnographic and relational information from 46 international organizations was collected through a self-administered semistructured questionnaire. From 46 international health cooperation organizations, 29 decision makers from 29 organizations participated (63.0% response rate). The structure and the strength of the network was evaluated in terms of density, closeness, clustering, and centralization. The statistical analysis was done using computer programs that included UCINET, Pajek, and Microsoft Access. We found a structurally centralized theoretical network, whose nodes were clustered into four central subgroups linked by a shared vision. The leadership, influence, and political interests reflected the formal and technical-cooperation linkages, the formal support for health systems based on primary health care, and the flow of resources being more often technical ones than financial ones. The interorganizational relational components and the social-action ties that were identified could help in the development and consolidation of a thematic network for advocacy and for the management of technical and financial assistance that supports primary health care in the Americas. The linkages for joint action that were identified could advance international cooperation in developing health systems based on primary health care, once PAHO formulates clear implementation strategies and takes a leadership position in mobilizing financial resources and in creating informal and interpersonal linkages for action.

A Preliminary Rhetoric of Technical Copywriting.

ERIC Educational Resources Information Center

Henson, Leigh

1994-01-01

Discusses the rhetorical elements of technical copywriting, including its shared communicative aims with technical writing; authorship considerations such as ethics, education, and professionalism; and the concerns of promotional strategy, audience analysis, choice of media and materials, writing strategy, and style. (SR)

NASA Integrated Space Communications Network

NASA Technical Reports Server (NTRS)

Tai, Wallace; Wright, Nate; Prior, Mike; Bhasin, Kul

2012-01-01

The NASA Integrated Network for Space Communications and Navigation (SCaN) has been in the definition phase since 2010. It is intended to integrate NASA s three existing network elements, i.e., the Space Network, Near Earth Network, and Deep Space Network, into a single network. In addition to the technical merits, the primary purpose of the Integrated Network is to achieve a level of operating cost efficiency significantly higher than it is today. Salient features of the Integrated Network include (a) a central system element that performs service management functions and user mission interfaces for service requests; (b) a set of common service execution equipment deployed at the all stations that provides return, forward, and radiometric data processing and delivery capabilities; (c) the network monitor and control operations for the entire integrated network are conducted remotely and centrally at a prime-shift site and rotating among three sites globally (a follow-the-sun approach); (d) the common network monitor and control software deployed at all three network elements that supports the follow-the-sun operations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The goal of the US Department of Energy (DOE) Underground Coal Conversion (UCC) program is to develop the technology to produce clean fuels from coal deposits that are unsuitable for commercial exploitation by conventional mining techniques. The highest priority is to develop and demonstrate, in conjunction with industry, a commercially feasible process for underground gasification of low-rank coal in the 1985 to 1987 time period. The DOE program has stimulated industry interest and activity in developing UCC technology. Several major energy corporations and utilities have invested private funds in UCC research and development (R and D) projects. Results of themore » program to date indicate that, while UCC is technically feasible, it still contains some process unknowns, environmental risks, and economic risks that require R and D. In order to contribute to the national energy goals, a strong DOE program that incorporates maximum industry involvement is planned. The program's strategy is to remove the high-risk elements of UCC by resolving technical, environmental, and economic uncertainties. This will enable industry to assume responsibility for commercialization of the technology. Thus, the elements of the program have been designed to: provide detailed design and operational data that industry can scale-up with confidence; provide accurate and complete cost estimates that can be scaled-up and will allow comparison with alternative processes; provide detailed environmental impact and control data to allow industry to implement projects that will meet applicable standards; verify the reliability of continuous operation of UCC processes; and show that UCC processes have the flexibility to meet a variety of commercial needs.« less

The NASA/DOD aerospace knowledge diffusion research project: A research agenda

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Kennedy, John M.

1990-01-01

The project has both immediate and long term purposes. In the first instance it provides a practical and pragmatic basis for understanding how the results of NASA/DoD research diffuse into the aerospace R and D process. Over the long term it provides an empirical basis for understanding the aerospace knowledge diffusion process itself, and its implications at the individual, organizational, national, and international levels. The project is studying the major barriers to effective knowledge diffusion. This project will provide descriptive and analytical data regarding the flow of scientific and technical information (STI). It will examine both channels used to communicate information and the social system of the aerospace knowledge diffusion process.

7 CFR Exhibit D to Subpart K of... - Amendment to Technical and Supervisory Assistance Grant Agreement

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 13 2012-01-01 2012-01-01 false Amendment to Technical and Supervisory Assistance Grant Agreement D Exhibit D to Subpart K of Part 1944 Agriculture Regulations of the Department of... Technical and Supervisory Assistance Grants Pt. 1944, Subpt. K, Exh. D Exhibit D to Subpart K of Part 1944...

7 CFR Exhibit D to Subpart K of... - Amendment to Technical and Supervisory Assistance Grant Agreement

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 13 2013-01-01 2013-01-01 false Amendment to Technical and Supervisory Assistance Grant Agreement D Exhibit D to Subpart K of Part 1944 Agriculture Regulations of the Department of... Technical and Supervisory Assistance Grants Pt. 1944, Subpt. K, Exh. D Exhibit D to Subpart K of Part 1944...

7 CFR Exhibit D to Subpart K of... - Amendment to Technical and Supervisory Assistance Grant Agreement

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 13 2014-01-01 2013-01-01 true Amendment to Technical and Supervisory Assistance Grant Agreement D Exhibit D to Subpart K of Part 1944 Agriculture Regulations of the Department of... Technical and Supervisory Assistance Grants Pt. 1944, Subpt. K, Exh. D Exhibit D to Subpart K of Part 1944...

7 CFR Exhibit D to Subpart K of... - Amendment to Technical and Supervisory Assistance Grant Agreement

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 13 2011-01-01 2009-01-01 true Amendment to Technical and Supervisory Assistance Grant Agreement D Exhibit D to Subpart K of Part 1944 Agriculture Regulations of the Department of... Technical and Supervisory Assistance Grants Pt. 1944, Subpt. K, Exh. D Exhibit D to Subpart K of Part 1944...

7 CFR Exhibit D to Subpart K of... - Amendment to Technical and Supervisory Assistance Grant Agreement

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 13 2010-01-01 2009-01-01 true Amendment to Technical and Supervisory Assistance Grant Agreement D Exhibit D to Subpart K of Part 1944 Agriculture Regulations of the Department of... Technical and Supervisory Assistance Grants Pt. 1944, Subpt. K, Exh. D Exhibit D to Subpart K of Part 1944...

Design and Delivery of Technical Module for the Business Intelligence Course

ERIC Educational Resources Information Center

Wang, Shouhong; Wang, Hai

2013-01-01

IS programs are increasingly being called on to offer courses in business intelligence. This article presents the pedagogical design and the delivery method of a practicable technical module for a non-technically oriented Business Intelligence course. It is a tutorial for the instructors who wish to incorporate a practical technical element in…

Influence of Psychological Factors on Product Development. Lessons from Aerospace and other Industries

NASA Astrophysics Data System (ADS)

Kamata, E. S.

2002-10-01

Product development is a major determinant of quality and cost as companies throughout the world struggle to optimize product development processes. Engineering tasks are usually implicitly assumed to be a primarily technical activity, but in reality they feature numerous nontechnical factors as well. This book focuses on the interrelationships of social, technical, and organizational aspects of the product development process. Cases observed in industry and research laboratories are presented and interpreted based on the socio-technical system approach (Emery / Trist) of examining the reciprocal relationship between the technical and the social subsystems. This book is primarily intended for engineering and quality professionals who want to know the limitations of current methods used in product development, to examine the so-called soft factors by means of grounded studies of their effect on R&D performance, not only to acknowledge the influence of soft factors but to actively consider their potential to improve the work environment. Academic researchers of the topic will also find many references and material for advanced courses on project and quality management. In addition to numerous cases from the aerospace industry, its general solution concepts are generalizable to other industries in which the high degree of product complexity necessitates effective interaction among different disciplines. The historical evaluation is neither intended for introductory purposes nor to propose a return to the past, but as a survey of the relevant factors to be applied in present and future projects. The author holds a degree in Electronics Engineering from the Instituto Tecnológico de Aeronautica, Brazil, as well as a PhD in Administration Sciences from the Swiss Federal Institute of Technology in Zurich, Switzerland. He draws on profound academic research as well as a wealth of practical experience in avionics, telecommunications, systems control, and the space industry. His professional biography includes activities in development, quality of development, reliability, testability and university lecturing. He also holds a commercial pilot license. Link: http://www.wkap.nl/prod/b/1-4020-0807-4

Health care multidisciplinary teams: The sociotechnical approach for an integrated system-wide perspective.

PubMed

Marsilio, Marta; Torbica, Aleksandra; Villa, Stefano

The current literature on the enabling conditions of multidisciplinary teams focuses on the singular dimensions of the organizations (i.e., human resources, clinical pathways, objects) without shedding light on to the way in which these organizational factors interact and mutually influence one another. Drawing on a system perspective of organizations, the authors analyze the organizational patterns that promote and support multidisciplinary teams and how they interrelate and interact to enforce the organization work system. The authors develop a modified sociotechnical system (STS) model to understand how the two dimensions of technical (devices/tools, layout/organization of space, core process standardization) and social (organizational structure, management of human resources and operations) can facilitate the implementation of multidisciplinary teams in health care. The study conducts an empirical analysis based on a sample of hospital adopters of transcatheter aortic valve implantation using the revised STS model. The modified STS model applied to the case studies improves our understanding of the critical implementation factors of a multidisciplinary approach and the importance of coordinating radical changes in the technical and the social subsystems of health care organizations. The analysis informs that the multidisciplinary effort is not a sequential process and that the interplay between the two subsystems needs to be managed efficaciously as an integrated organizational whole to deliver the goals set. Hospital managers must place equal focus on the closely interrelated technical and social dimensions by investing in (a) shared layouts and spaces that cross the boundaries of the specialized health care units, (b) standardization of the core processes through the implementation of local clinical pathways, (c) structured knowledge management mechanisms, (d) the creation of clinical directorates, and (e) the design of a planning and budgeting system that integrates the multidisciplinary concept.

Sustaining engineering codes of ethics for the twenty-first century.

PubMed

Michelfelder, Diane; Jones, Sharon A

2013-03-01

How much responsibility ought a professional engineer to have with regard to supporting basic principles of sustainable development? While within the United States, professional engineering societies, as reflected in their codes of ethics, differ in their responses to this question, none of these professional societies has yet to put the engineer's responsibility toward sustainability on a par with commitments to public safety, health, and welfare. In this paper, we aim to suggest that sustainability should be included in the paramountcy clause because it is a necessary condition to ensure the safety, health, and welfare of the public. Part of our justification rests on the fact that to engineer sustainably means among many things to consider social justice, understood as the fair and equitable distribution of social goods, as a design constraint similar to technical, economic, and environmental constraints. This element of social justice is not explicit in the current paramountcy clause. Our argument rests on demonstrating that social justice in terms of both inter- and intra-generational equity is an important dimension of sustainability (and engineering). We also propose that embracing sustainability in the codes while recognizing the role that social justice plays may elevate the status of the engineer as public intellectual and agent of social good. This shift will then need to be incorporated in how we teach undergraduate engineering students about engineering ethics.

Autism and Folate Deficiency

DTIC Science & Technology

2010-05-01

social interaction that remains to be characterized more fully. Conclusion Ablation of genes in the folate pathway may result in abnormal adult...W81XWH-09-1-0246 TITLE: Autism and Folate Deficiency PRINCIPAL INVESTIGATOR: Richard H. Finnell, Ph.D...5a. CONTRACT NUMBER W81XWH-09-1-0246 Autism and Folate Deficiency 5b. GRANT NUMBER AR080064-Concept Award 5c. PROGRAM ELEMENT NUMBER

The "Inverse Relationship" between Social Capital and Sport: A Qualitative Exploration of the Influence of Social Networks on the Development of Athletes

ERIC Educational Resources Information Center

Rosso, Edoardo G. F.

2015-01-01

Sport players' likelihood to fulfil their career expectations is influenced by both technical and non-technical aspects, including self-drive, self-confidence and access to high-quality coaching and to positive learning environments. Among other factors, belonging in the "right" social networks may help players to gain access to critical…

A new holistic approach to vulnerability assessment to natural hazards of socio-economic systems by means of Graph Theory

NASA Astrophysics Data System (ADS)

Arosio, Marcello; Martina, Mario L. V.

2017-04-01

In the last years, the relations and interactions between multi-hazards, vulnerability, exposure and resilience spheres are assuming more and more attention and the scientific community recognized that they are very dynamic, complex and interconnected. The traditional approaches define risk as the potential economic, social and environmental consequences due to a hazardous phenomenon in a specific period. Although there have been major improvements in recent years, there are still some limitation in term of a holistic approach that is able to include the emergent value hidden in the relation and interaction between the different spheres. Furthermore, the emergent behaviour of a society makes the collective risk greater than the sum of the parts and this requires a holistic, systematic and integrated approach. For this reason, it is important to consider the connections between elements to assess properly the vulnerability of systems. In a system (e.g. road, hospital and ecological network, etc.), or in a System of System (e.g. socio-technical urban service), there are critical elements that, beyond the intrinsic vulnerability, can be characterize by greater or lower vulnerability because of their physical, geographical, cyber or logical connections. To understand the system response to a perturbation, and therefore its resilience, is necessary not only to represent but also to quantify the relative importance of the elements and their interconnections. To this aim, we propose an innovative approach in the field of natural risk assessment based on the properties of graph G=(N,L). A graph consists of two sets N (nodes) and L (links): the nodes represent the single exposed elements (physical, social, environmental, etc.) to a hazard, while the links (or connections) represent the interaction between the elements. This approach encourages the risk assessment to a new prospective: from reductionist to holistic. The final goal is to provide insight in understanding how to quantify integrated collective vulnerability, resilience and risk.

Adaptive Management: From More Talk to Real Action

NASA Astrophysics Data System (ADS)

Williams, Byron K.; Brown, Eleanor D.

2014-02-01

The challenges currently facing resource managers are large-scale and complex, and demand new approaches to balance development and conservation goals. One approach that shows considerable promise for addressing these challenges is adaptive management, which by now is broadly seen as a natural, intuitive, and potentially effective way to address decision-making in the face of uncertainties. Yet the concept of adaptive management continues to evolve, and its record of success remains limited. In this article, we present an operational framework for adaptive decision-making, and describe the challenges and opportunities in applying it to real-world problems. We discuss the key elements required for adaptive decision-making, and their integration into an iterative process that highlights and distinguishes technical and social learning. We illustrate the elements and processes of the framework with some successful on-the-ground examples of natural resource management. Finally, we address some of the difficulties in applying learning-based management, and finish with a discussion of future directions and strategic challenges.

Technical Preparation: Preparing Students for Success. A Position Paper Presented by the Wisconsin Association of Secondary Vocational Administrators 1991-1992.

ERIC Educational Resources Information Center

Peterson, Charlene; And Others

Technical Preparation (Tech Prep) programs include basic skills and competencies to improve students' school-to-work transition. The following elements characterize Tech Prep: designed for grades 9-14, leading to an technical associate degree; parallels college preparatory program; offers technical program of study in business enterprise,…

Development of a behavioural marker system for scrub practitioners' non-technical skills (SPLINTS system).

PubMed

Mitchell, Lucy; Flin, Rhona; Yule, Steven; Mitchell, Janet; Coutts, Kathy; Youngson, George

2013-04-01

Adverse events still occur despite ongoing efforts to reduce harm to patients. Contributory factors to adverse events are often due to limitations in clinicians' non-technical skills (e.g. communication, situation awareness), rather than deficiencies in technical competence. We developed a behavioural rating system to provide a structured means for teaching and assessing scrub practitioners' (i.e. nurse, technician, operating department practitioner) non-technical skills. Psychologists facilitated focus groups (n = 4) with experienced scrub practitioners (n = 16; 4 in each group) to develop a preliminary taxonomy. Focus groups reviewed lists of non-technical-skill-related behaviours that were extracted from an interview study. The focus groups labelled skill categories and elements and also provided examples of good and poor behaviours for those skills. An expert panel (n = 2 psychologists; n = 1 expert nurse) then used an iterative process to individually and collaboratively review and refine those data to produce a prototype skills taxonomy. A preliminary taxonomy containing eight non-technical skill categories with 28 underlying elements was produced. The expert panel reduced this to three categories (situation awareness, communication and teamwork, task management), each with three underlying elements. The system was called the Scrub Practitioners' List of Intraoperative Non-Technical Skills system. A scoring system and a user handbook were also developed. A prototype behavioural rating system for scrub practitioners' non-technical skills was developed, to aid in teaching and providing formative assessment. This important aspect of performance is not currently explicitly addressed in any educational route to qualify as a scrub practitioner. © 2012 Blackwell Publishing Ltd.

[Construction of information management-based virtual forest landscape and its application].

PubMed

Chen, Chongcheng; Tang, Liyu; Quan, Bing; Li, Jianwei; Shi, Song

2005-11-01

Based on the analysis of the contents and technical characteristics of different scale forest visualization modeling, this paper brought forward the principles and technical systems of constructing an information management-based virtual forest landscape. With the combination of process modeling and tree geometric structure description, a software method of interactively and parameterized tree modeling was developed, and the corresponding renderings and geometrical elements simplification algorithms were delineated to speed up rendering run-timely. As a pilot study, the geometrical model bases associated with the typical tree categories in Zhangpu County of Fujian Province, southeast China were established as template files. A Virtual Forest Management System prototype was developed with GIS component (ArcObject), OpenGL graphics environment, and Visual C++ language, based on forest inventory and remote sensing data. The prototype could be used for roaming between 2D and 3D, information query and analysis, and virtual and interactive forest growth simulation, and its reality and accuracy could meet the needs of forest resource management. Some typical interfaces of the system and the illustrative scene cross-sections of simulated masson pine growth under conditions of competition and thinning were listed.

Social inequalities in the face of scientific and technological development: an antinomy or an historic problem?

PubMed

Delgado, Guilherme Costa

2017-07-01

This paper aims to conduct a conceptual analysis of the relationship between scientific and technical progress and social equality, or the reduction of inequalities. We examine this relationship by drawing on three theoretical perspectives: 1) ethical economics, championed by classical economic thinkers and centered on utilitarian self-interest, 2) Mainstream theories of economic development espousing the endogenous link between labor productivity growth and technical progress, 3) the critique of theories of economic development that emerged in the second half of the twentieth century, including Celso Furtado's critique of the theory of underdevelopment, emphasizing the prevalence of egalitarian tendencies, and ecological economics, which suggest alternative paths to those set by "classical" theories of development. The fundamental antinomy posed by the title of this article, characterized by an intrinsic contradiction between technical progress and social equality, strictly presupposes the ethical economics perspective, dominated by the social relations that constitute the "social order".

2012 Technical Corrections Fact Sheet

EPA Pesticide Factsheets

Final Rule: 2012 Technical Corrections, Clarifying and Other Amendments to theGreenhouse Gas Reporting Rule, and Confidentiality Determinations for Certain DataElements of the Fluorinated Gas Source Category

Semiannual Technical Summary, 1 October 1989 - 31 Mar 1990 (Royal Norwegian Council for Scientific and Industrial Research)

DTIC Science & Technology

1990-06-01

I TASK WORK UNIT 1400 Wilson Blvd. ELEMENT NO. NO NOA INO SOW TAS rc ° Arlington, VA 22209-2308 R&D | PHASE 3 5.0 |No.OO3A2 11. TITLE (Include...not only has considerable benefits for the recognition of seismic phases , but also provides a domain in which the relative proportions of P, SV and S11...sensitive to source location and phase velocity. The study suggests that the Moho saddle, a feature which appears to be well defined and documented in a

Propulsion and Power Rapid Response R&D Support. Task Order 0006: Engineering Research, Testing, and Technical Analyses of Advanced Propulsion Combustion Concepts, Mechanical Systems, Lubricants and Fuels: Mechanical Systems

DTIC Science & Technology

2009-02-01

element state data are provided. (3) The objective of the third study conducted by PKG, Inc. was to conduct geometric modeling of race defects...A., (1995), “The effect of test machine on the failure mode in lubricated rolling contact of silicon nitride,” Tribology International, Vol. 28, pp...A192. (10) Crook, A. W. (1952), A study of some impacts between metal bodies by a piezoelectric method, Proceedings of Royal Society, A212. (11

Cross Domain Deterrence: Livermore Technical Report, 2014-2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnes, Peter D.; Bahney, Ben; Matarazzo, Celeste

2016-08-03

Lawrence Livermore National Laboratory (LLNL) is an original collaborator on the project titled “Deterring Complex Threats: The Effects of Asymmetry, Interdependence, and Multi-polarity on International Strategy,” (CDD Project) led by the UC Institute on Global Conflict and Cooperation at UCSD under PIs Jon Lindsay and Erik Gartzke , and funded through the DoD Minerva Research Initiative. In addition to participating in workshops and facilitating interaction among UC social scientists, LLNL is leading the computational modeling effort and assisting with empirical case studies to probe the viability of analytic, modeling and data analysis concepts. This report summarizes LLNL work on themore » CDD Project to date, primarily in Project Years 1-2, corresponding to Federal fiscal year 2015. LLNL brings two unique domains of expertise to bear on this Project: (1) access to scientific expertise on the technical dimensions of emerging threat technology, and (2) high performance computing (HPC) expertise, required for analyzing the complexity of bargaining interactions in the envisioned threat models. In addition, we have a small group of researchers trained as social scientists who are intimately familiar with the International Relations research. We find that pairing simulation scientists, who are typically trained in computer science, with domain experts, social scientists in this case, is the most effective route to developing powerful new simulation tools capable of representing domain concepts accurately and answering challenging questions in the field.« less

Assessing Nurse Anaesthetists' Non-Technical Skills in the operating room.

PubMed

Lyk-Jensen, H T; Jepsen, R M H G; Spanager, L; Dieckmann, P; Østergaard, D

2014-08-01

Incident reporting and fieldwork in operating rooms have shown that some of the errors that arise in anaesthesia relate to inadequate use of non-technical skills. To provide a tool for training and feedback on nurse anaesthetists' non-technical skills, this study aimed to adapt the Anaesthetists' Non-Technical Skills (ANTS) as a behavioural marker system for the formative assessment of nurse anaesthetists' non-technical skills in the operating room. A qualitative approach with focus group interviews was used to identify the non-technical skills of nurse anaesthetists in the operating room. The interview data were transcribed verbatim. Directed content analysis was used to code and sort data deductively into the ANTS categories: task management, team working, situation awareness and decision making. The prototype named Nurse Anaesthetists' Non-Technical Skills (N-ANTS) was presented and discussed in a group of subject matter experts to ensure face validity. The N-ANTS system consists of the same four categories as ANTS and 15 underlying elements. Three to five good and poor behavioural markers for each element were identified. The headings and definitions of the categories and elements were adjusted to encompass the behavioural markers in N-ANTS. The differences that emerged mainly reflected statements regarding the establishment of role, competence, and task delegation. A behavioural marker system, N-ANTS, for nurse anaesthetists was adapted from a behavioural marker system, ANTS, for anaesthesiologists. © 2014 The Acta Anaesthesiologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

The Role of Communication in the Professional Socialization Process.

ERIC Educational Resources Information Center

Barnett, George A.; Carson, David L.

To explore the professional socialization of technical writers and communicators, 98 professional technical communicators were administered a questionnaire identifying key concepts in the field. On seven occasions, professionals, teachers, and graduate students were asked to estimate how greatly these concepts, together with four additional terms…

Hydraulic Testing of Polymer Matrix Composite 102mm Tube Section Technical Report

DTIC Science & Technology

2018-04-01

Technical Report ARWSB-TR-18025 Hydraulic Testing of Polymer Matrix Composite 102mm Tube Section Technical Report Lucas B...1. REPORT DATE (DD-MM-YYYY) April 2018 2. REPORT TYPE Technical 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Hydraulic Testing of...Polymer Matrix Composite 102mm Tube Section Technical Report 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER

Technosocial Modeling of IED Threat Scenarios and Attacks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitney, Paul D.; Brothers, Alan J.; Coles, Garill A.

2009-03-23

This paper describes an approach for integrating sociological and technical models to develop more complete threat assessment. Current approaches to analyzing and addressing threats tend to focus on the technical factors. This paper addresses development of predictive models that encompass behavioral as well as these technical factors. Using improvised explosive device (IED) attacks as motivation, this model supports identification of intervention activities 'left of boom' as well as prioritizing attack modalities. We show how Bayes nets integrate social factors associated with IED attacks into general threat model containing technical and organizational steps from planning through obtaining the IED to initiationmore » of the attack. The social models are computationally-based representations of relevant social science literature that describes human decision making and physical factors. When combined with technical models, the resulting model provides improved knowledge integration into threat assessment for monitoring. This paper discusses the construction of IED threat scenarios, integration of diverse factors into an analytical framework for threat assessment, indicator identification for future threats, and future research directions.« less

Four conceptual issues to consider in integrating social and environmental factors in risk and impact assessments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Domínguez-Gómez, J. Andrés, E-mail: andres@uhu.es

In the last twenty years, both the increase in academic production and the expansion of professional involvement in Environmental Impact Assessment (EIA) and Social Impact Assessment (SIA) have evidenced growing scientific and business interest in risk and impact analysis. However, this growth has not brought with it parallel progress in addressing the main shortcomings of EIA/SIA, i.e. insufficient integration of environmental and social factors into development project analyses and, in cases where the social aspects are considered, technical-methodological failings in their analysis and assessment. It is clear that these weaknesses carry with them substantial threats to the sustainability (social, environmentalmore » and economic) of projects which impact on the environment, and consequently to the local contexts where they are carried out and to the delicate balance of the global ecosystem. This paper argues that, in a sociological context of complexity and dynamism, four conceptual elements should underpin approaches to socio-environmental risk and impact assessment in development projects: a theoretical base in actor–network theory; an ethical grounding in values which are internationally recognized (though not always fulfilled in practice); a (new) epistemological-scientific base; and a methodological foundation in social participation. - Highlights: • A theoretical foundation in actor–network theory • An ethical grounding in values which are internationally recognized, but rarely carried through into practice • A (new) epistemological-scientific base • A methodological foundation in social participation.« less

SERC 2014 2018 Technical Plan: 2016 Update

DTIC Science & Technology

2016-02-18

Contract Number: HQ0034-13-D-0004 February 18, 2016 SERC 2014-2018 Technical Plan Update SERC 2014-2018 Technical Plan: 2016 Update...UNCLASSIFIED / APPROVED FOR PUBLIC RELEASE Contract Number: HQ0034-13-D-0004 February 18, 2016 SERC 2014-2018 Technical Plan Update ii...18, 2016 SERC 2014-2018 Technical Plan Update iii TABLE OF CONTENTS Table of Contents

Gun Control for VBE-E: User Guide and Technical Description

DTIC Science & Technology

2006-11-01

Defence R& D Canada – Atlantic DEFENCE DÉFENSE & Gun Control for VBE-E User Guide and Technical Description Tania E. Wentzell Technical Memorandum...Defence R& D Canada – Atlantic Technical Memorandum DRDC Atlantic TM 2006-245 November 2006 DRDC Atlantic TM 2006-245...component of the distributed experimentation environment used by the Virtual Combat System (VCS) Group at Defence R& D Canada – Atlantic (DRDC Atlantic

The Independent Technical Analysis Process Final Report 2006-2007.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duberstein, Corey; Ham, Kenneth; Dauble, Dennis

2007-03-01

The Bonneville Power Administration (BPA) contracted with the Pacific Northwest National Laboratory (PNNL) to provide technical analytical support for system-wide fish passage information (BPA Project No. 2006-010-00). The goal of this project was to produce rigorous technical analysis products using independent analysts and anonymous peer reviewers. This project provided an independent technical source for non-routine fish passage analyses while allowing routine support functions to be performed by other well-qualified entities. The Independent Technical Analysis Process (ITAP) was created to provide non-routine analysis for fish and wildlife agencies and tribes in particular and the public in general on matters related tomore » juvenile and adult salmon and steelhead passage through the mainstem hydrosystem. The process was designed to maintain the independence of analysts and reviewers from parties requesting analyses, to avoid potential bias in technical products. The objectives identified for this project were to administer a rigorous, transparent process to deliver unbiased technical assistance necessary to coordinate recommendations for storage reservoir and river operations that avoid potential conflicts between anadromous and resident fish. Seven work elements, designated by numbered categories in the Pisces project tracking system, were created to define and accomplish project goals as follows: (1) 118 Coordination - Coordinate technical analysis and review process: (a) Retain expertise for analyst/reviewer roles. (b) Draft research directives. (c) Send directive to the analyst. (d) Coordinate two independent reviews of the draft report. (e) Ensure reviewer comments are addressed within the final report. (2) 162 Analyze/Interpret Data - Implement the independent aspects of the project. (3) 122 Provide Technical Review - Implement the review process for the analysts. (4) 132 Produce Annual Report - FY06 annual progress report with Pisces Disseminate (5) 161 Disseminate Raw/Summary Data and Results - Post technical products on the ITAP web site. (6) 185-Produce Pisces Status Report - Provide periodic status reports to BPA. (7) 119 Manage and Administer Projects - project/contract administration.« less

Should Project Managers Buy Technical Data

DTIC Science & Technology

2017-04-06

Should Project Managers Buy Technical Data? Jerry Harper April 6, 2017 PUBLISHED BY The Defense...intellectual property (IP) management and technical data rights (TDR) strategies. According to DoD Instruction 5000.02 (DoD, 2017), project managers (PMs...Defense Authorization Act NDI ................nondevelopmental item PM ................. project manager R&D ...............research and development

47 CFR 15.510 - Technical requirements for through D-wall imaging systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical requirements for through D-wall imaging systems. 15.510 Section 15.510 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Ultra-Wideband Operation § 15.510 Technical requirements for through D-wall imaging...

Air Force Research Laboratory Wright Site Guide to Technical Publishing

DTIC Science & Technology

2005-04-01

Scientific and Technical Reports—Elements, Organization, and Design manual (and a version modified for documents generated for AFRL) • Merriam-Webster’s...notice page --SF 298 --original graphics /halftones Indicate the following on the letter of transmittal sheet: --quantity of copies required for...Elements, Organization and Design ? The WRS CDRL for a final report requires that the standard be followed. The only exception is SBIR Phase 1

Social Media Analytics: A New Approach for Cyberspace Enabled Understanding of Operational Environments

DTIC Science & Technology

2013-12-10

NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER Major Sean Lyons 5e. TASK NUMBER 5f. WORK...Advance Research Projects Agency DOD Department of Defense FM Field Manual IC Intelligence Community IO Information Operations IP Internet...Utah, Central Intelligence Agency funding of the Recorded Future Company, and Defense Advanced Research Projects Agency, XDATA project . 2

Dynamic Network Change Detection

DTIC Science & Technology

2008-12-01

Change Detection 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT...Fisher and Mackenzie, 1922). These methods are used in quality engineering to detect small changes in a process (Montgomery, 1991; Ryan , 2000). Larger...Social Network Modeling and Analysis: Workshop Summary and Papers, Ronald Breiger, Kathleen Carley, and Philippa Pattison, (Eds

ECUT (Energy Conversion and Utilization Technologies) program: Biocatalysis project

NASA Technical Reports Server (NTRS)

Baresi, Larry

1989-01-01

The Annual Report presents the fiscal year (FY) 1988 research activities and accomplishments, for the Biocatalysis Project of the U.S. Department of Energy, Energy Conversion and Utilization Technologies (ECUT) Division. The ECUT Biocatalysis Project is managed by the Jet Propulsion Laboratory, California Institute of Technology. The Biocatalysis Project is a mission-oriented, applied research and exploratory development activity directed toward resolution of the major generic technical barriers that impede the development of biologically catalyzed commercial chemical production. The approach toward achieving project objectives involves an integrated participation of universities, industrial companies and government research laboratories. The Project's technical activities were organized into three work elements: (1) The Molecular Modeling and Applied Genetics work element includes research on modeling of biological systems, developing rigorous methods for the prediction of three-dimensional (tertiary) protein structure from the amino acid sequence (primary structure) for designing new biocatalysis, defining kinetic models of biocatalyst reactivity, and developing genetically engineered solutions to the generic technical barriers that preclude widespread application of biocatalysis. (2) The Bioprocess Engineering work element supports efforts in novel bioreactor concepts that are likely to lead to substantially higher levels of reactor productivity, product yields and lower separation energetics. Results of work within this work element will be used to establish the technical feasibility of critical bioprocess monitoring and control subsystems. (3) The Bioprocess Design and Assessment work element attempts to develop procedures (via user-friendly computer software) for assessing the energy-economics of biocatalyzed chemical production processes, and initiation of technology transfer for advanced bioprocesses.

ECUT (Energy Conversion and Utilization Technologies) program: Biocatalysis project

NASA Astrophysics Data System (ADS)

Baresi, Larry

1989-03-01

The Annual Report presents the fiscal year (FY) 1988 research activities and accomplishments, for the Biocatalysis Project of the U.S. Department of Energy, Energy Conversion and Utilization Technologies (ECUT) Division. The ECUT Biocatalysis Project is managed by the Jet Propulsion Laboratory, California Institute of Technology. The Biocatalysis Project is a mission-oriented, applied research and exploratory development activity directed toward resolution of the major generic technical barriers that impede the development of biologically catalyzed commercial chemical production. The approach toward achieving project objectives involves an integrated participation of universities, industrial companies and government research laboratories. The Project's technical activities were organized into three work elements: (1) The Molecular Modeling and Applied Genetics work element includes research on modeling of biological systems, developing rigorous methods for the prediction of three-dimensional (tertiary) protein structure from the amino acid sequence (primary structure) for designing new biocatalysis, defining kinetic models of biocatalyst reactivity, and developing genetically engineered solutions to the generic technical barriers that preclude widespread application of biocatalysis. (2) The Bioprocess Engineering work element supports efforts in novel bioreactor concepts that are likely to lead to substantially higher levels of reactor productivity, product yields and lower separation energetics. Results of work within this work element will be used to establish the technical feasibility of critical bioprocess monitoring and control subsystems. (3) The Bioprocess Design and Assessment work element attempts to develop procedures (via user-friendly computer software) for assessing the energy-economics of biocatalyzed chemical production processes, and initiation of technology transfer for advanced bioprocesses.

NADA/DOD Aerospace Knowledge Diffusion Research Project. Report number 19: The US government technical report and the transfer of federally funded aerospace R/D: An analysis of five studies

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the 'NASA/DoD Aerospace Knowledge Diffusion Research Project'. In this report, we summarize the literature on technical reprts and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from five studies of our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report and close with a brief overview of on-going research into the use of the U.S. government technical report as a rhetorical device for transferring federally funded aerospace R&D.

[Improvement of sanitary and epidemiological safety of rail transport--a requirement of the new legislation of the Russian Federation].

PubMed

2012-01-01

Brief analysis of the legal framework in recent years, both in the sphere of technical regulation, and in the field of sanitary and epidemiological welfare of the population is presented in this article. The necessity of inclusion in the technical regulations for the safety of railway rolling stock and elements of railway infrastructure the requirements for sanitary-epidemiological safety and hygiene regulations has been proved. Fragments of technical regulations for railway equipment and infrastructure elements, including the basic requirements for the sanitary-epidemiological security are presented. The position of authors in the processing of the regulatory framework in the field of sanitary-epidemiological welfare of population in standardization documents in accordance with the requirements of federal law "On technical regulation" has been reflected.

Case study research: training interdisciplinary engineers with context-dependent knowledge

NASA Astrophysics Data System (ADS)

Chanan, Amit; Vigneswaran, Saravanamuth; Kandasamy, Jaya

2012-03-01

It is now widely acknowledged that water management discipline is transforming, from being a public health and flood prevention challenge of the nineteenth century to a multi-dimensional challenge of water security for the twenty-first century. In order to train water engineers to be capable of working with this holistic multi-dimensional approach, a new paradigm in engineering education is required. Adjustments already made to undergraduate coursework are not enough; this new paradigm requires modifications to the PhD in engineering, with greater emphasis on interdisciplinary case study research. Such a change can deliver PhD graduates with both sufficient social and technical knowledge, who can then go on to become the hybrid lecturers crucially needed for training future water engineers.

Flood warnings in coastal areas: how do social and behavioural patterns influence alert services?

NASA Astrophysics Data System (ADS)

Pescaroli, G.; Magni, M.

2015-01-01

Many studies discuss the economic and technical aspects of flood warnings. Less attention has been given to the social and psychological patterns that affect alert services. In particular, the literature focuses on warnings activated in river basins or marine environments without providing clear evidence of relevance to Mediterranean coastal areas, even though these are subjected to growing flood risk related to climate change. This paper is a first attempt to bridge this gap. Our research develops an in- depth analysis of the village of Cesenatico on the Adriatic Sea coast. Here the municipality adopted two complementary warning systems: a siren and an alert via Short Message Service (SMS). The analysis focuses on a survey conducted in 2011 and 2012 with 228 participants. The relationships between social and behavioural variables and warning services are investigated, and so are flood preparedness and information dissemination. Qualitative evidence from informal interviews is used to support the understanding of key responses. The conclusions show how different social and behavioural patterns can influence the effectiveness and use of warning systems, regardless of the technology adopted and the structural mitigation measures implemented. Education, training and accountability are seen to be critical elements for improvement. Finally, the statistical output is used to suggest new questions and new directions for research.

The evolution of primate general and cultural intelligence

PubMed Central

Reader, Simon M.; Hager, Yfke; Laland, Kevin N.

2011-01-01

There are consistent individual differences in human intelligence, attributable to a single ‘general intelligence’ factor, g. The evolutionary basis of g and its links to social learning and culture remain controversial. Conflicting hypotheses regard primate cognition as divided into specialized, independently evolving modules versus a single general process. To assess how processes underlying culture relate to one another and other cognitive capacities, we compiled ecologically relevant cognitive measures from multiple domains, namely reported incidences of behavioural innovation, social learning, tool use, extractive foraging and tactical deception, in 62 primate species. All exhibited strong positive associations in principal component and factor analyses, after statistically controlling for multiple potential confounds. This highly correlated composite of cognitive traits suggests social, technical and ecological abilities have coevolved in primates, indicative of an across-species general intelligence that includes elements of cultural intelligence. Our composite species-level measure of general intelligence, ‘primate gS’, covaried with both brain volume and captive learning performance measures. Our findings question the independence of cognitive traits and do not support ‘massive modularity’ in primate cognition, nor an exclusively social model of primate intelligence. High general intelligence has independently evolved at least four times, with convergent evolution in capuchins, baboons, macaques and great apes. PMID:21357224

Human Rights and the Global Fund to Fight AIDS, Tuberculosis and Malaria: How Does a Large Funder of Basic Health Services Meet the Challenge of Rights-Based Programs?

PubMed

Jürgens, Ralf; Csete, Joanne; Lim, Hyeyoung; Timberlake, Susan; Smith, Matthew

2017-12-01

The Global Fund to Fight AIDS, Tuberculosis and Malaria was created to greatly expand access to basic services to address the three diseases in its name. From its beginnings, its governance embodied some human rights principles: civil society is represented on its board, and the country coordination mechanisms that oversee funding requests to the Global Fund include representatives of people affected by the diseases. The Global Fund's core strategies recognize that the health services it supports would not be effective or cost-effective without efforts to reduce human rights-related barriers to access and utilization of health services, particularly those faced by socially marginalized and criminalized persons. Basic human rights elements were written into Global Fund grant agreements, and various technical support measures encouraged the inclusion in funding requests of programs to reduce human rights-related barriers. A five-year initiative to provide intensive technical and financial support for the scaling up of programs to reduce these barriers in 20 countries is ongoing.

Project Manager’s Guide to the Scientific and Technical Information (STINFO) Program and Technical Publications Process

DTIC Science & Technology

1993-12-01

Iaporta .. y be definitive for the tubjoct proaentod, exploratory in natura, or an evaluation of critical Aubayato• or of technical problema , 4...International Security 9 Social and Natural Science Studies Field 41 Edit: (Type 3) -Entry of an invalid code when Performance Type is "C" or "M" will...analysis SF Foreign area social science research SP Foreign area policy planAing research BF Identifies databases with data on foreign forces or

76 FR 35103 - Training and Qualification Requirements for Check Airmen and Flight Instructors; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-16

... which initial and transition flight training must include an in-flight element. Technical Amendment This.... 28471; Amendment Nos. 121-355 and 135-125] RIN 2120-AF08 Training and Qualification Requirements for Check Airmen and Flight Instructors; Technical Amendment AGENCY: Federal Aviation Administration (FAA...

7 CFR Exhibit D to Subpart I of... - Self-Help Technical Assistance Grant Predevelopment Agreement

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 13 2011-01-01 2009-01-01 true Self-Help Technical Assistance Grant Predevelopment... SERVICE AGENCY, DEPARTMENT OF AGRICULTURE (CONTINUED) PROGRAM REGULATIONS (CONTINUED) HOUSING Self-Help Technical Assistance Grants Pt. 1944, Subpt. I, Exh. D Exhibit D to Subpart I of Part 1944—Self-Help...

7 CFR Exhibit D to Subpart I of... - Self-Help Technical Assistance Grant Predevelopment Agreement

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 13 2010-01-01 2009-01-01 true Self-Help Technical Assistance Grant Predevelopment... SERVICE AGENCY, DEPARTMENT OF AGRICULTURE (CONTINUED) PROGRAM REGULATIONS (CONTINUED) HOUSING Self-Help Technical Assistance Grants Pt. 1944, Subpt. I, Exh. D Exhibit D to Subpart I of Part 1944—Self-Help...

An Empirical Investigation of Social Bonds and Juvenile Delinquency in Hong Kong

ERIC Educational Resources Information Center

Chui, Wing Hong; Chan, Heng Choon Oliver

2012-01-01

Background: Although there are studies that tested Hirschi's social bond elements with Asian samples in the past, however, no study has examined all his social bond elements. Objective: Therefore, this study aims to test all Hirschi's social bond elements with a sample of secondary educated male and female Hong Kong adolescents. Methods: A total…

Screen Layout Design: Research into the Overall Appearance of the Screen.

ERIC Educational Resources Information Center

Grabinger, R. Scott

1989-01-01

Examines the current state of research into the visual effects of screen designs used in computer-assisted instruction and suggests areas for future efforts. Topics discussed include technical elements and comprehensibility elements in layout design; single element and multiple element research methodologies; dependent variables; and learning…

An Instrumental Perspective on CSCL Systems

ERIC Educational Resources Information Center

Lonchamp, Jacques

2012-01-01

The theory of instrumental genesis of Rabardel relates the social and the technical through the concept of instrument. An instrument is defined as a mixed entity made up by an artifact, the technical/material part, and a set of utilization schemes, the social/behavioural part, which both result from users' constructive activities. This theory is…

75 FR 1271 - Technical Revisions to the Supplemental Security Income (SSI) Regulations on Income and Resources

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-11

... SOCIAL SECURITY ADMINISTRATION 20 CFR Part 416 [Docket No. SSA 2008-0034] RIN 0960-AG66 Technical Revisions to the Supplemental Security Income (SSI) Regulations on Income and Resources AGENCY: Social... revisions reflect legislative changes found in the Consolidated Appropriations Act of 2001 (CAA), the...

Reading in the Writing Class: Conventions, Socialization, and Revision.

ERIC Educational Resources Information Center

Werner, Warren W.

On the premise that the kind of writing done in business and technical writing classes is a social act, the business and technical writing courses at Auburn University (Alabama) use peer interaction, revision, and audience awareness to help students become aware of and internalize the conventions of writing. Students are required to read each…

A New Stage in the Development of Secondary Vocational-Technical Schools

ERIC Educational Resources Information Center

Sedakov, V.

1977-01-01

Recommends that projected growth in the technical-vocational sector of education in the Soviet Union be accompanied by qualitative improvements in areas of political socialization, cultural transmission, and technical development. (Author/DB)

DRDC Technical Stream Integrated Capabilities and Vision

DTIC Science & Technology

2011-09-01

Brenda Fraser Allan Keefe Nada Pavlovic Doug Saunders Phil Terhaar Defence R&D Canada Technical Memorandum DRDC Toronto...Beechinor Hamid Boland Brenda Fraser Allan Keefe Nada Pavlovic Doug Saunders Phil Terhaar Defence R&D Canada – Toronto...Technical Memorandum DRDC Toronto TM 2011-017 September 2011 Principal Author Original signed by Allan Keefe Allan Keefe Technical

Trust and Decision Making: An Empirical Platform

DTIC Science & Technology

2008-06-01

13th ICCRTS “C2 for Complex Endeavors” Trust and Decision Making : An Empirical Platform Topic(s): Cognitive and Social Issues...and Decision Making : An Empirical Platform 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e...PERSON a. REPORT unclassified b. ABSTRACT unclassified c. THIS PAGE unclassified Trust and Decision Making : An Empirical Platform Dr. Joseph B

Conservation of Stone Cladding on the FAÇADE of Royal Palace in Caserta

NASA Astrophysics Data System (ADS)

Titomanlio, I.

2013-07-01

The beauty of cultural heritage and monumental architecture, is often linked to their non-structural elements and decorative stones façades cladding. The collapse of these elements causes significant consequences that interest the social, the economic, the historical and the technical fields. Several regulatory documents and literature studies contain methods to address the question of relief and of the risk analysis and due to the non - structural stones security. Among the references are widespread international regulatory documents prepared by the Federal Emergency Management Agency of the United States by Applied Technology Council and California. In Italy there are some indications contained in the Norme Tecniche per le Costruzioni and the Direttiva del Presidente del Consiglio dei Ministri in 2007, finalize to the reduction of seismic risk assessment of cultural heritage. The paper, using normative references and scientific researches, allows to analyze on Royal Palace of Caserta the safety and the preservation of cultural heritage and the vulnerability of non-structural stones façade cladding. Using sophisticated equipments of Laboratory ARS of the Second University of Naples, it was possible to analyze the collapse of stone elements due to degradation caused by natural phenomena of deterioration (age of the building, type of materials, geometries , mode of fixing of the elements themselves). The paper explains the collapse mechanisms of stones façade cladding of Luigi Vanvitelli Palace.

Concept for Classifying Facade Elements Based on Material, Geometry and Thermal Radiation Using Multimodal Uav Remote Sensing

NASA Astrophysics Data System (ADS)

Ilehag, R.; Schenk, A.; Hinz, S.

2017-08-01

This paper presents a concept for classification of facade elements, based on the material and the geometry of the elements in addition to the thermal radiation of the facade with the usage of a multimodal Unmanned Aerial Vehicle (UAV) system. Once the concept is finalized and functional, the workflow can be used for energy demand estimations for buildings by exploiting existing methods for estimation of heat transfer coefficient and the transmitted heat loss. The multimodal system consists of a thermal, a hyperspectral and an optical sensor, which can be operational with a UAV. While dealing with sensors that operate in different spectra and have different technical specifications, such as the radiometric and the geometric resolution, the challenges that are faced are presented. Addressed are the different approaches of data fusion, such as image registration, generation of 3D models by performing image matching and the means for classification based on either the geometry of the object or the pixel values. As a first step towards realizing the concept, the result from a geometric calibration with a designed multimodal calibration pattern is presented.

Semi-Infinite Geology Modeling Algorithm (SIGMA): a Modular Approach to 3D Gravity

NASA Astrophysics Data System (ADS)

Chang, J. C.; Crain, K.

2015-12-01

Conventional 3D gravity computations can take up to days, weeks, and even months, depending on the size and resolution of the data being modeled. Additional modeling runs, due to technical malfunctions or additional data modifications, only compound computation times even further. We propose a new modeling algorithm that utilizes vertical line elements to approximate mass, and non-gridded (point) gravity observations. This algorithm is (1) magnitudes faster than conventional methods, (2) accurate to less than 0.1% error, and (3) modular. The modularity of this methodology means that researchers can modify their geology/terrain or gravity data, and only the modified component needs to be re-run. Additionally, land-, sea-, and air-based platforms can be modeled at their observation point, without having to filter data into a synthesized grid.

Changing behavior towards sustainable practices using Information Technology.

PubMed

Iveroth, Einar; Bengtsson, Fredrik

2014-06-15

This article addresses the question of how to change individuals' behavior towards more sustainable practices using Information Technology (IT). By following a multidisciplinary and socio-technical perspective, this inquiry is answered by applying a new framework-The Commonality Framework for IT-enabled Change-on a case study of sustainable behavioral change. The framework is grounded in practice theory and is used to analyze the implementation of an IT-system aimed at changing citizens' behavior towards more sustainable transport logistics and procurement in Uppsala, Sweden. The article applies case study research design and the empirical data consists of surveys, in-depth and semi-structured interviews, observations and archival documents. The results show how the change towards sustainable practices is an entanglement of both social and technical-structural elements across time. In this process, structures such as IT are the enablers, and the actors and their social activities are the tipping-point factors that ultimately determine the success of changing individuals' behavior towards a more sustainable direction. This article provides a more balanced view of how both actor and structure related properties interact during the on-going work with change towards greater sustainability practices than earlier research has offered. More specifically, the article offers both a lower-level theory and a method from which we can analyze change processes where technology is seen in its context, and where both technology and the human actor is brought forth to center stage. Copyright © 2014 Elsevier Ltd. All rights reserved.

Integrated Space Asset Management Database and Modeling

NASA Technical Reports Server (NTRS)

MacLeod, Todd; Gagliano, Larry; Percy, Thomas; Mason, Shane

2015-01-01

Effective Space Asset Management is one key to addressing the ever-growing issue of space congestion. It is imperative that agencies around the world have access to data regarding the numerous active assets and pieces of space junk currently tracked in orbit around the Earth. At the center of this issues is the effective management of data of many types related to orbiting objects. As the population of tracked objects grows, so too should the data management structure used to catalog technical specifications, orbital information, and metadata related to those populations. Marshall Space Flight Center's Space Asset Management Database (SAM-D) was implemented in order to effectively catalog a broad set of data related to known objects in space by ingesting information from a variety of database and processing that data into useful technical information. Using the universal NORAD number as a unique identifier, the SAM-D processes two-line element data into orbital characteristics and cross-references this technical data with metadata related to functional status, country of ownership, and application category. The SAM-D began as an Excel spreadsheet and was later upgraded to an Access database. While SAM-D performs its task very well, it is limited by its current platform and is not available outside of the local user base. Further, while modeling and simulation can be powerful tools to exploit the information contained in SAM-D, the current system does not allow proper integration options for combining the data with both legacy and new M&S tools. This paper provides a summary of SAM-D development efforts to date and outlines a proposed data management infrastructure that extends SAM-D to support the larger data sets to be generated. A service-oriented architecture model using an information sharing platform named SIMON will allow it to easily expand to incorporate new capabilities, including advanced analytics, M&S tools, fusion techniques and user interface for visualizations. In addition, tight control of information sharing policy will increase confidence in the system, which would encourage industry partners to provide commercial data. Combined with the integration of new and legacy M&S tools, a SIMON-based architecture will provide a robust environment that can be extended and expanded indefinitely.

47 CFR 51.307 - Duty to provide access on an unbundled basis to network elements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... network elements. 51.307 Section 51.307 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Carriers § 51.307 Duty to provide access on an unbundled basis to network elements. (a) An incumbent LEC... service, nondiscriminatory access to network elements on an unbundled basis at any technically feasible...

47 CFR 51.307 - Duty to provide access on an unbundled basis to network elements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... network elements. 51.307 Section 51.307 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED... Carriers § 51.307 Duty to provide access on an unbundled basis to network elements. (a) An incumbent LEC... service, nondiscriminatory access to network elements on an unbundled basis at any technically feasible...

Development of 3D Atlas of Metalworking Equipment

NASA Astrophysics Data System (ADS)

Yevgenyevna Maslennikova, Olga; Borisovna Nazarova, Olga; Aleksandrovna Chudinova, Yulia

2018-05-01

The paper is dedicated to solving the problem of developing innovative educational systems able to train personnel of complex and dangerous manufacturing industries (such as in metallurgy) to control the process not only under regular conditions, but in emergency and pre-emergency situations as well. At that, such educational systems shall transform training of future and current engineers into a professional activity, model both subject matter and social content of their professional labor. Key characteristics of a 3D atlas of equipment as an educational system are given, as it provides immersion of trainees into professional environment. Requirements for such systems are defined (functional, information, software and technical). Stages of development of a 3D atlas of equipment as an automated system are given, allowing one to get closer to yet another problem that of IT specialist training so that they are able to design, implement and deploy such systems.

Recovery Act. Development and Validation of an Advanced Stimulation Prediction Model for Enhanced Geothermal System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gutierrez, Marte

The research project aims to develop and validate an advanced computer model that can be used in the planning and design of stimulation techniques to create engineered reservoirs for Enhanced Geothermal Systems. The specific objectives of the proposal are to: 1) Develop a true three-dimensional hydro-thermal fracturing simulator that is particularly suited for EGS reservoir creation. 2) Perform laboratory scale model tests of hydraulic fracturing and proppant flow/transport using a polyaxial loading device, and use the laboratory results to test and validate the 3D simulator. 3) Perform discrete element/particulate modeling of proppant transport in hydraulic fractures, and use the resultsmore » to improve understand of proppant flow and transport. 4) Test and validate the 3D hydro-thermal fracturing simulator against case histories of EGS energy production. 5) Develop a plan to commercialize the 3D fracturing and proppant flow/transport simulator. The project is expected to yield several specific results and benefits. Major technical products from the proposal include: 1) A true-3D hydro-thermal fracturing computer code that is particularly suited to EGS, 2) Documented results of scale model tests on hydro-thermal fracturing and fracture propping in an analogue crystalline rock, 3) Documented procedures and results of discrete element/particulate modeling of flow and transport of proppants for EGS applications, and 4) Database of monitoring data, with focus of Acoustic Emissions (AE) from lab scale modeling and field case histories of EGS reservoir creation.« less

Recovery Act. Development and Validation of an Advanced Stimulation Prediction Model for Enhanced Geothermal Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gutierrez, Marte

2013-12-31

This research project aims to develop and validate an advanced computer model that can be used in the planning and design of stimulation techniques to create engineered reservoirs for Enhanced Geothermal Systems. The specific objectives of the proposal are to; Develop a true three-dimensional hydro-thermal fracturing simulator that is particularly suited for EGS reservoir creation; Perform laboratory scale model tests of hydraulic fracturing and proppant flow/transport using a polyaxial loading device, and use the laboratory results to test and validate the 3D simulator; Perform discrete element/particulate modeling of proppant transport in hydraulic fractures, and use the results to improve understandmore » of proppant flow and transport; Test and validate the 3D hydro-thermal fracturing simulator against case histories of EGS energy production; and Develop a plan to commercialize the 3D fracturing and proppant flow/transport simulator. The project is expected to yield several specific results and benefits. Major technical products from the proposal include; A true-3D hydro-thermal fracturing computer code that is particularly suited to EGS; Documented results of scale model tests on hydro-thermal fracturing and fracture propping in an analogue crystalline rock; Documented procedures and results of discrete element/particulate modeling of flow and transport of proppants for EGS applications; and Database of monitoring data, with focus of Acoustic Emissions (AE) from lab scale modeling and field case histories of EGS reservoir creation.« less

Finite element generation of arbitrary 3-D fracture networks for flow analysis in complicated discrete fracture networks

NASA Astrophysics Data System (ADS)

Zhang, Qi-Hua

2015-10-01

Finite element generation of complicated fracture networks is the core issue and source of technical difficulty in three-dimensional (3-D) discrete fracture network (DFN) flow models. Due to the randomness and uncertainty in the configuration of a DFN, the intersection lines (traces) are arbitrarily distributed in each face (fracture and other surfaces). Hence, subdivision of the fractures is an issue relating to subdivision of two-dimensional (2-D) domains with arbitrarily-distributed constraints. When the DFN configuration is very complicated, the well-known approaches (e.g. Voronoi Delaunay-based methods and advancing-front techniques) cannot operate properly. This paper proposes an algorithm to implement end-to-end connection between traces to subdivide 2-D domains into closed loops. The compositions of the vertices in the common edges between adjacent loops (which may belong to a single fracture or two connected fractures) are thus ensured to be topologically identical. The paper then proposes an approach for triangulating arbitrary loops which does not add any nodes to ensure consistency of the meshes at the common edges. In addition, several techniques relating to tolerance control and improving code robustness are discussed. Finally, the equivalent permeability of the rock mass is calculated for some very complicated DFNs (the DFN may contain 1272 fractures, 633 connected fractures, and 16,270 closed loops). The results are compared with other approaches to demonstrate the veracity and efficiency of the approach proposed in this paper.

Etude de faisabilite de l'insertion d'une membrane elastomere a renfort textile dans l'aspirateur d'une centrale hydroelectrique

NASA Astrophysics Data System (ADS)

Delorme, Rolland

The generation of electrical energy in Quebec, estimated to 200 TWh, comes from hydroelectric generating stations for 96 % which are at the heart of provincial ecological and economic challenges. An important amount of research has been devoted to improving the hydrodynamic profile of hydraulic turbines to maximize their energy efficiency. However, few studies have focused on the draft tube in hydroelectric power plants, which is the duct where water flows out after crossing the turbine. Recent calculations performed by Alstom Power & Transport Canada Inc. revealed that the shape modulation of the draft tube could increase the hydroelectric generating station performance. The goal of this research was to assess the feasibility of this shape modification in existing draft tubes with inflatable composite membranes. The study consisted first of building an experimental setup to test the inflation of at membranes made up of a fiberglass-reinforced rubber composite. The inflated membranes were digitized with an optical equipment enabling 3D representations of their deflections. The second part of the study aimed at building finite element models reproducing the same experiments and enabling the design of more complicated membranes. The study confirmed the technical feasibility of designing and manufacturing such a membrane for the targeted application. However the large-scale roll-out will require to manufacture 3D membranes with the proper anchoring system. Keywords: reinforced rubber composite, reinforced elastomer composite, textile reinforcement, finite element modeling, mechanical behavior.

Pedagogical, Social and Technical Designs of a Blended Synchronous Learning Environment

ERIC Educational Resources Information Center

Wang, Qiyun; Huang, Changqin

2018-01-01

In this study, a blended synchronous learning environment (BSLE) was designed from pedagogical, social and technical perspectives. It was created for a group of master's students to attend lessons in the classroom and at the same time allow a few of them to join the identical sessions using video conferencing from different sites. The purpose of…

Social Embodiment of Technical Devices: Eyeglasses over the Centuries and According to Their Uses

ERIC Educational Resources Information Center

Veyrat, Nicolas; Blanco, Eric; Trompette, Pascale

2008-01-01

This article is an attempt to prepare the ground for the analysis and theorization of the connection between the body and technical devices emerging from miniaturized wearable technologies. The research object is a secular and common "body object," namely, eyeglasses. The article reviews the social history of this artifact and analyzes its…

41 CFR Appendix C to Chapter 301 - Standard Data Elements for Federal Travel [Traveler Identification

Code of Federal Regulations, 2014 CFR

2014-07-01

... education, in scientific, professional, technical, mechanical, trade, clerical, fiscal, administrative, or... Data Elements for Federal Travel [Accounting & Certification] Group name Data elements Description Accounting Classification Accounting Code Agency accounting code. Non-Federal Source Indicator Per Diem...

Elements of a Research Report.

ERIC Educational Resources Information Center

Schurter, William J.

This guide for writing research or technical reports discusses eleven basic elements of such reports and provides examples of "good" and "bad" wordings. These elements are the title, problem statement, purpose statement, need statement, hypothesis, assumptions, procedures, limitations, terminology, conclusion and recommendations. This guide is…

[NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 1:] The value of Scientific and Technical Information (STI), its relationship to Research and Development (R&D), and its use by US aerospace engineers and scientists

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Glassman, Myron; Barclay, Rebecca O.; Oliu, Walter E.

1990-01-01

The relationship between scientific and technical information (STI), its use by aerospace engineers and scientists, and the aerospace R&D process is examined. Data are presented from studies of the role of STI in the performance and management of R&D activities and the behavior of engineers when using and seeking information. Consideration is given to the information sources used to solve technical problems, the production and use of technical communications, and the use of libraries, technical information centers, and on-line data bases.

NASA/DoD Aerospace Knowledge Diffusion Research Project. Paper 29: The US government technical report and the transfer of federally funded aerospace R and D

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1993-01-01

This article discusses the U.S. government technical report and the transfer of federally funded aerospace research and development in a conceptual framework of the federal government as a producer of scientific and technical information. The article summarizes current literature and research and discusses U.S. government technical report use and the importance of using data obtained from the NASA/DoD Aerospace Knowledge Diffusion Research Project. The authors make a case for changing existing U.S. technology policy and present a research agenda for the U.S. government technical report.

Robust object tracking techniques for vision-based 3D motion analysis applications

NASA Astrophysics Data System (ADS)

Knyaz, Vladimir A.; Zheltov, Sergey Y.; Vishnyakov, Boris V.

2016-04-01

Automated and accurate spatial motion capturing of an object is necessary for a wide variety of applications including industry and science, virtual reality and movie, medicine and sports. For the most part of applications a reliability and an accuracy of the data obtained as well as convenience for a user are the main characteristics defining the quality of the motion capture system. Among the existing systems for 3D data acquisition, based on different physical principles (accelerometry, magnetometry, time-of-flight, vision-based), optical motion capture systems have a set of advantages such as high speed of acquisition, potential for high accuracy and automation based on advanced image processing algorithms. For vision-based motion capture accurate and robust object features detecting and tracking through the video sequence are the key elements along with a level of automation of capturing process. So for providing high accuracy of obtained spatial data the developed vision-based motion capture system "Mosca" is based on photogrammetric principles of 3D measurements and supports high speed image acquisition in synchronized mode. It includes from 2 to 4 technical vision cameras for capturing video sequences of object motion. The original camera calibration and external orientation procedures provide the basis for high accuracy of 3D measurements. A set of algorithms as for detecting, identifying and tracking of similar targets, so for marker-less object motion capture is developed and tested. The results of algorithms' evaluation show high robustness and high reliability for various motion analysis tasks in technical and biomechanics applications.

Health Education Telecommunications Experiment

NASA Technical Reports Server (NTRS)

Whalen, A. A.

1975-01-01

The Health/Education Telecommunications Experiment carried out with Applications Technology Satellite-6 is described. The experiment tested the effectiveness of color television broadcasts to over 120 low-cost receivers in rural areas. Five types of earth stations were involved: receive-only terminals (ROT), an intensive terminal consisting of the ROT plus a VHF transmitter and receiver; comprehensive S and C-band terminals having the capability of transmitting the video signal plus four audio channels; and the main originating stations. Additional supporting elements comprise 120 video receive terminals, 51 telephony transceivers, and 8 video originating terminals of 3 different parts. Technical parameters were measured to within 1 dB of the calculated values.

20 CFR 666.220 - What information must be included in a State Board's application for an Incentive Grant?

Code of Federal Regulations, 2010 CFR

2010-04-01

... the Carl D. Perkins Vocational and Technical Education Act. (3) The State exceeded the State... vocational and technical programs under the Carl D. Perkins Vocational and Technical Education Act. (WIA sec...

20 CFR 666.220 - What information must be included in a State Board's application for an Incentive Grant?

Code of Federal Regulations, 2011 CFR

2011-04-01

... the Carl D. Perkins Vocational and Technical Education Act. (3) The State exceeded the State... vocational and technical programs under the Carl D. Perkins Vocational and Technical Education Act. (WIA sec...

78 FR 41331 - Defense Federal Acquisition Regulation Supplement; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-10

... DEPARTMENT OF DEFENSE Defense Acquisition Regulations System 48 CFR Part 225 Defense Federal Acquisition Regulation Supplement; Technical Amendments AGENCY: Defense Acquisition Regulations System, Department of Defense (DoD). ACTION: Final rule. SUMMARY: DoD is making technical amendment to the Defense...

Project Interface Requirements Process Including Shuttle Lessons Learned

NASA Technical Reports Server (NTRS)

Bauch, Garland T.

2010-01-01

Most failures occur at interfaces between organizations and hardware. Processing interface requirements at the start of a project life cycle will reduce the likelihood of costly interface changes/failures later. This can be done by adding Interface Control Documents (ICDs) to the Project top level drawing tree, providing technical direction to the Projects for interface requirements, and by funding the interface requirements function directly from the Project Manager's office. The interface requirements function within the Project Systems Engineering and Integration (SE&I) Office would work in-line with the project element design engineers early in the life cycle to enhance communications and negotiate technical issues between the elements. This function would work as the technical arm of the Project Manager to help ensure that the Project cost, schedule, and risk objectives can be met during the Life Cycle. Some ICD Lessons Learned during the Space Shuttle Program (SSP) Life Cycle will include the use of hardware interface photos in the ICD, progressive life cycle design certification by analysis, test, & operations experience, assigning interface design engineers to Element Interface (EI) and Project technical panels, and linking interface design drawings with project build drawings

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 35: The US government technical report and aerospace knowledge diffusion: Results of an on-going investigation

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Khan, A. Rahman; Barclay, Rebecca O.; Kennedy, John M.

1993-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded (U.S.) R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this paper, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from two surveys (one of five studies) of our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report and close with a brief overview of on-going research into the use of the U.S. government technical report as a rhetorical device for transferring federally funded aerospace R&D.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report number 21: US aerospace industry librarians and technical information specialists as information intermediaries: Results of the phase 2 survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DoD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis U.S. aerospace industry librarians and technical information specialists as information intermediaries.

NASA/DoD Aerospace Knowledge Diffusion Research Project: Report 43: The Technical Communication Practices of U.S. Aerospace Engineers and Scientists: Results of the Phase 1 Mail Survey -- Manufacturing and Production Perspective

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1996-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communication practices of U.S. aerospace engineers and scientists who were members of the Society of Manufacturing Engineers.

Systematic analysis of video data from different human-robot interaction studies: a categorization of social signals during error situations.

PubMed

Giuliani, Manuel; Mirnig, Nicole; Stollnberger, Gerald; Stadler, Susanne; Buchner, Roland; Tscheligi, Manfred

2015-01-01

Human-robot interactions are often affected by error situations that are caused by either the robot or the human. Therefore, robots would profit from the ability to recognize when error situations occur. We investigated the verbal and non-verbal social signals that humans show when error situations occur in human-robot interaction experiments. For that, we analyzed 201 videos of five human-robot interaction user studies with varying tasks from four independent projects. The analysis shows that there are two types of error situations: social norm violations and technical failures. Social norm violations are situations in which the robot does not adhere to the underlying social script of the interaction. Technical failures are caused by technical shortcomings of the robot. The results of the video analysis show that the study participants use many head movements and very few gestures, but they often smile, when in an error situation with the robot. Another result is that the participants sometimes stop moving at the beginning of error situations. We also found that the participants talked more in the case of social norm violations and less during technical failures. Finally, the participants use fewer non-verbal social signals (for example smiling, nodding, and head shaking), when they are interacting with the robot alone and no experimenter or other human is present. The results suggest that participants do not see the robot as a social interaction partner with comparable communication skills. Our findings have implications for builders and evaluators of human-robot interaction systems. The builders need to consider including modules for recognition and classification of head movements to the robot input channels. The evaluators need to make sure that the presence of an experimenter does not skew the results of their user studies.

Systematic analysis of video data from different human–robot interaction studies: a categorization of social signals during error situations

PubMed Central

Giuliani, Manuel; Mirnig, Nicole; Stollnberger, Gerald; Stadler, Susanne; Buchner, Roland; Tscheligi, Manfred

2015-01-01

Human–robot interactions are often affected by error situations that are caused by either the robot or the human. Therefore, robots would profit from the ability to recognize when error situations occur. We investigated the verbal and non-verbal social signals that humans show when error situations occur in human–robot interaction experiments. For that, we analyzed 201 videos of five human–robot interaction user studies with varying tasks from four independent projects. The analysis shows that there are two types of error situations: social norm violations and technical failures. Social norm violations are situations in which the robot does not adhere to the underlying social script of the interaction. Technical failures are caused by technical shortcomings of the robot. The results of the video analysis show that the study participants use many head movements and very few gestures, but they often smile, when in an error situation with the robot. Another result is that the participants sometimes stop moving at the beginning of error situations. We also found that the participants talked more in the case of social norm violations and less during technical failures. Finally, the participants use fewer non-verbal social signals (for example smiling, nodding, and head shaking), when they are interacting with the robot alone and no experimenter or other human is present. The results suggest that participants do not see the robot as a social interaction partner with comparable communication skills. Our findings have implications for builders and evaluators of human–robot interaction systems. The builders need to consider including modules for recognition and classification of head movements to the robot input channels. The evaluators need to make sure that the presence of an experimenter does not skew the results of their user studies. PMID:26217266

The Future Cybersecurity Workforce: Going Beyond Technical Skills for Successful Cyber Performance.

PubMed

Dawson, Jessica; Thomson, Robert

2018-01-01

One of the challenges in writing an article reviewing the current state of cyber education and workforce development is that there is a paucity of quantitative assessment regarding the cognitive aptitudes, work roles, or team organization required by cybersecurity professionals to be successful. In this review, we argue that the people who operate within the cyber domain need a combination of technical skills, domain specific knowledge, and social intelligence to be successful. They, like the networks they operate, must also be reliable, trustworthy, and resilient. Defining the knowledge, skills, attributes, and other characteristics is not as simple as defining a group of technical skills that people can be trained on; the complexity of the cyber domain makes this a unique challenge. There has been little research devoted to exactly what attributes individuals in the cyber domain need. What research does exist places an emphasis on technical and engineering skills while discounting the important social and organizational influences that dictate success or failure in everyday settings. This paper reviews the literature on cyber expertise and cyber workforce development to identify gaps and then argues for the important contribution of social fit in the highly complex and heterogenous cyber workforce. We then identify six assumptions for the future of cybersecurity workforce development, including the requirement for systemic thinkers, team players, a love for continued learning, strong communication ability, a sense of civic duty, and a blend of technical and social skill. Finally, we make recommendations for social and cognitive metrics which may be indicative of future performance in cyber work roles to provide a roadmap for future scholars.

Challenges for Planning and Maintaining of Urban Rain Harvesting Systems- the case of Hammarby Sjöstad and Årstafältet in Stockholm

NASA Astrophysics Data System (ADS)

Suleiman, Lina

2017-04-01

Planners and policymakers' concern escalates over conventional systems dealing with rains in cities based on domination and control of nature rather than harmony and design with nature. A new spatial planning paradigm is needed to put in place systems which mimic natural water systems and promise multiple values instead of systems consider rain as a source of problem. However, such approach embodies significant planning challenges. Urban rain harvesting systems (URHs) are inherently viewed as 'sociotechnical' systems. As such, planning processes should consider the interdependence of 'social' and 'technical' aspects as essential elements if a transition towards sustainable urban water systems is to be realised. Drawing on a common understanding for what urban rain harvesting systems should deliver in terms of 'functions' and 'added values', a generic planning framework is developed to inform practitioners on how the 'socio' and 'technical' elements should be assimilated in a long-term and integrated planning processes of URHs. Using the developed framework, the paper examines the planning and maintenance processes of urban rain harvesting systems in Årstafältet and Hammarby Sjöstad respectively. Results show that planners lack a common operational understanding on how these systems should be designed holistically in a long term and integrated planning processes creating working gabs or positional conflicts. In practice, urban planners and water engineers look at these systems as either urban design component or water drainage system to deal with technical functions hindering a smooth transition path towards urban rain harvesting systems. The paper concludes on the urgency for reordering roles and relations within a new set-up organisation to incubate these systems in long-term planning and maintenance processes. Key words: 'Sociotechnical' system, Water, Planning, Urban Rain Harvesting systems (URHs), Hammarby Sjostad and Årstafältet

Graduate Professional Education from a Community of Practice Perspective: The Role of Social and Technical Networking

NASA Astrophysics Data System (ADS)

Polin, Linda G.

This chapter describes academic life at the intersection of three related topics: community of practice (CoP), a pedagogical model; digital culture, as embodied in the current and future student population; and post-secondary education, in particular graduate professional education. The aim is to illustrate ways in which social computing applications enable the use of a CoP model in graduate professional education. The illustrations are drawn from two hybrid, or blended, degree programs (a mix of face-to-face and online interactions) at the graduate school of education and psychology at Pepperdine University. These fully accredited programs have each been in operation for more than a decade. One is the MA degree in educational technology, begun in 1998; the other is the EdD degree in educational technology leadership, begun in 1995.

Common Core State Standards for Literacy in History/Social Studies, Science, and Technical Subjects for English Language Learners

ERIC Educational Resources Information Center

de Oliveira, Luciana C., Ed.

2016-01-01

This volume in the Common Core State Standards (CCSS) for English Language Learners series was designed to deepen teacher's knowledge and provides instructional approaches and practices for supporting grades 6-12 ELLs as they meet the ambitious expectations of the CCSS for Literacy in History/Social Studies, Science, and Technical Subjects. This…

Common Core State Standards for English Language Arts & Literacy in History/Social Studies, Science, and Technical Subjects

ERIC Educational Resources Information Center

Common Core State Standards Initiative, 2010

2010-01-01

The Common Core State Standards for English Language Arts & Literacy in History/Social Studies, Science, and Technical Subjects ("the Standards") are the culmination of an extended, broad-based effort to fulfill the charge issued by the states to create the next generation of K-12 standards in order to help ensure that all students…

An Analysis of Operational Art: Field Force Synchronization in Vietnam from 1965-1967

DTIC Science & Technology

2013-05-23

a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1...Degree Programs Robert F. Baumann, Ph.D. The opinions and conclusions expressed herein are those of the student author and do not...military and social operational variables, the specific elements of operational design do not prove as useful. Muddled and cloudy perspectives of the

The Operation Method of Smarter City Based on Ecological Theory

NASA Astrophysics Data System (ADS)

Fan, C.; Fan, H. Y.

2017-10-01

As the city and urbanization’s accelerated pace has caused galloping population, the urban framework is extending with increasingly complex social problems. The urban management tends to become complicated and the governance seems more difficult to pursue. exploring the urban management’s new model has attracted local governments’ urgent attention. tcombines the guiding ideology and that management’s practices based on ecological theory, explains the Smarter city Ecology Managementmodel’s formation, makes modern urban management’s comparative analysis and further defines the aforesaid management mode’s conceptual model. Based on the smarter city system theory’s ecological carrying capacity, the author uses mathematical model to prove the coordination relationship between the smarter city Ecology Managementmode’s subsystems, demonstrates that it can improve the urban management’s overall level, emphasizes smarter city management integrity, believing that urban system’s optimization is based on each subsystem being optimized, attaching the importance to elements, structure, and balance between each subsystem and between internal elements. Through the establishment of the smarter city Ecology Managementmodel’s conceptual model and theoretical argumentation, it provides a theoretical basis and technical guidance to that model’s innovation.

Unique Chernobyl Cranes for Deconstruction Activities in the New Safe Confinement - 13542

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parameswaran, N.A. Vijay; Chornyy, Igor; Owen, Rob

2013-07-01

The devastation left behind from the Chernobyl nuclear power plant (ChNPP) Unit 4 accident which occurred on April 26, 1986 presented unparalleled technical challenges to the world engineering and scientific community. One of the largest tasks that are in progress is the design and construction of the New Safe Confinement (NSC). The NSC is an engineered enclosure for the entire object shelter (OS) that includes a suite of process equipment. The process equipment will be used for the dismantling of the destroyed Chernobyl Nuclear Power Plant (ChNPP) Unit. One of the major mechanical handling systems to be installed in themore » NSC is the Main Cranes System (MCS). The planned decontamination and decommissioning or dismantling (D and D) activities will require the handling of heavily shielded waste disposal casks containing nuclear fuel as well as lifting and transporting extremely large structural elements. These activities, to be performed within the NSC, will require large and sophisticated cranes. The article will focus on the unique design features of the MCS for the D and D activities. (authors)« less

History, race, and attachment to place among elders in the rural all-black towns of Oklahoma.

PubMed

McAuley, W J

1998-01-01

This research examines place attachment among older residents of the all-Black towns of Oklahoma. Social-historical occurrences, personal experiences associated with race, and expressed differences between social-historical groupings of older African Americans influence the level of social and autobiographical insideness among the elderly residents. The findings extend current conceptualizations of place attachment by showing that (a) place attachment is not a constant, even among long-term residents; (b) social-historical factors can play an important role in the level of place attachment; (c) race can be a salient element of place attachment; (d) experiences outside the community, such as racial discrimination, can influence the level of social and autobiographical bonding to the community; and (e) subgroup identity within minority groups can be associated with variations in community place attachment. The findings point to the value of carefully examining the issues of history and race in research focusing on older minority group members.

New research on women's low participation in science and technology

NASA Astrophysics Data System (ADS)

Stout, Jane

It is well known that women have historically been and continue to be grossly underrepresented in technical fields (i.e., the physical sciences, engineering, and computing). This presentation will address the following research questions: What dissuades women from entering into a technical career track, and what are women's experiences like within technical fields? At the same time, this presentation will acknowledge a shortcoming of decades of social science research and interventions designed to improve women's interest and persistence in technical fields: a narrow definition of ``women''. Given that the majority of women in colleges and universities (i.e., the typical sites of social science research) tend to be affluent and/or White, STEM education research that relies on convenience samples at colleges and universities paints a skewed picture of gender issues in technical fields. This presentation will showcase research findings that call into question conventional conceptions of gender disparities in technical fields. Specifically, the presentation will emphasize the importance of recognizing that women constitute more than their gender; women come from a diverse array of backgrounds, which no doubt play a role in the experience of being a woman in technical fields. By understanding the experiences of women from a broad array of demographics groups, the STEM education community can develop a corresponding set of strategies to recruit and retain women with diverse interests, experiences, and values (e.g., first generation versus second college students; women of different racial/ethnic backgrounds). The aim of this presentation is to promote social science research and interventions that acknowledge the nuanced experiences of diverse women in technical fields, in order to address the seemingly intractable problem of women's underrepresentation in technical fields. NSF DUE-1431112, NSF CNS-1246649.

The Pioneer Projects - Economical exploration of the solar system

NASA Technical Reports Server (NTRS)

Spahr, J. R.; Hall, C. F.

1975-01-01

The interplanetary Pioneer missions are reviewed in terms of management implications and cost control. The responsibilities, organizational structure, and management practices of the Pioneer Projects are presented. The lines of authority and areas of responsibility of the principal organizational elements supporting the Pioneer missions are identified, and the methods employed for maintaining effective and timely interactions among these elements are indicated. The technical and administrative functions of various organizational elements of the project are described. The management and control of activities prior to and during the hardware procurement phase are described to indicate the basis for obtaining visibility of the technical progress, utilization of resources, and cost performance of the contractors and other institutions supporting the Pioneer projects.

The Rise of Avatars in Positive Psychology: Enabling Military Cultures in a 3D World for Strengths of Character Development

DTIC Science & Technology

2010-03-01

York.  Piaget , J.  (1977).  The  development  of thought:   Equilibration of  cognitive  structures, trans.  A Rosin.  New York:  Viking Press.  17...Cultures in a 3D World for Strengths of Character Development 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT...educators believe warrior strengths of character  to know, decide, and act are  cognitively ,  affectively, and socially  developmental  in  nature.  Game

Mixing in 3D Sparse Multi-Scale Grid Generated Turbulence

NASA Astrophysics Data System (ADS)

Usama, Syed; Kopec, Jacek; Tellez, Jackson; Kwiatkowski, Kamil; Redondo, Jose; Malik, Nadeem

2017-04-01

Flat 2D fractal grids are known to alter turbulence characteristics downstream of the grid as compared to the regular grids with the same blockage ratio and the same mass inflow rates [1]. This has excited interest in the turbulence community for possible exploitation for enhanced mixing and related applications. Recently, a new 3D multi-scale grid design has been proposed [2] such that each generation of length scale of turbulence grid elements is held in its own frame, the overall effect is a 3D co-planar arrangement of grid elements. This produces a 'sparse' grid system whereby each generation of grid elements produces a turbulent wake pattern that interacts with the other wake patterns downstream. A critical motivation here is that the effective blockage ratio in the 3D Sparse Grid Turbulence (3DSGT) design is significantly lower than in the flat 2D counterpart - typically the blockage ratio could be reduced from say 20% in 2D down to 4% in the 3DSGT. If this idea can be realized in practice, it could potentially greatly enhance the efficiency of turbulent mixing and transfer processes clearly having many possible applications. Work has begun on the 3DSGT experimentally using Surface Flow Image Velocimetry (SFIV) [3] at the European facility in the Max Planck Institute for Dynamics and Self-Organization located in Gottingen, Germany and also at the Technical University of Catalonia (UPC) in Spain, and numerically using Direct Numerical Simulation (DNS) at King Fahd University of Petroleum & Minerals (KFUPM) in Saudi Arabia and in University of Warsaw in Poland. DNS is the most useful method to compare the experimental results with, and we are studying different types of codes such as Imcompact3d, and OpenFoam. Many variables will eventually be investigated for optimal mixing conditions. For example, the number of scale generations, the spacing between frames, the size ratio of grid elements, inflow conditions, etc. We will report upon the first set of findings from the 3DSGT by the time of the conference. {Acknowledgements}: This work has been supported partly by the EuHIT grant, 'Turbulence Generated by Sparse 3D Multi-Scale Grid (M3SG)', 2017. {References} [1] S. Laizet, J. C. Vassilicos. DNS of Fractal-Generated Turbulence. Flow Turbulence Combust 87:673705, (2011). [2] N. A. Malik. Sparse 3D Multi-Scale Grid Turbulence Generator. USPTO Application no. 14/710,531, Patent Pending, (2015). [3] J. Tellez, M. Gomez, B. Russo, J.M. Redondo. Surface Flow Image Velocimetry (SFIV) for hydraulics applications. 18th Int. Symposium on the Application of Laser Imaging Techniques in Fluid Mechanics, Lisbon, Portugal (2016).

Storying energy consumption: Collective video storytelling in energy efficiency social marketing.

PubMed

Gordon, Ross; Waitt, Gordon; Cooper, Paul; Butler, Katherine

2018-05-01

Despite calls for more socio-technical research on energy, there is little practical advice to how narratives collected through qualitative research may be melded with technical knowledge from the physical sciences such as engineering and then applied in energy efficiency social action strategies. This is despite established knowledge in the environmental management literature about domestic energy use regarding the utility of social practice theory and narrative framings that socialise everyday consumption. Storytelling is positioned in this paper both as a focus for socio-technical energy research, and as one potential practical tool that can arguably enhance energy efficiency interventions. We draw upon the literature on everyday social practices, and storytelling, to present our framework called 'collective video storytelling' that combines scientific and lay knowledge about domestic energy use to offer a practical tool for energy efficiency management. Collective video storytelling is discussed in the context of Energy+Illawarra, a 3-year cross-disciplinary collaboration between social marketers, human geographers, and engineers to target energy behavioural change within older low-income households in regional NSW, Australia. Copyright © 2018 Elsevier Ltd. All rights reserved.

76 FR 68429 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... documentation, U.S. Government and contractor engineering, technical, and logistics personnel support services, and other related elements of logistics support. (iv) Military Department: Navy (USMC) (SDH). (v.... Government and contractor engineering, technical, and logistics personnel [[Page 68432

Ka-Band MMIC Subarray Technology Program (Ka-Mist)

NASA Technical Reports Server (NTRS)

Pottinger, W.

1995-01-01

Ka-band monolithic microwave integrated circuit (MMIC) arrays have been considered as having high potential for increasing the capability of space, aircraft, and land mobile communication systems in terms of scan performance, data rate, link margin, and flexibility while offering a significant reduction in size, weight, and power consumption. Insertion of MMIC technology into antenna systems, particularly at millimeter wave frequencies using low power and low noise amplifiers in closed proximity to the radiating elements, offers a significant improvement in the array transmit efficiency, receive system noise figure, and overall array reliability. Application of active array technology also leads to the use of advanced beamforming techniques that can improve beam agility, diversity, and adaptivity to complex signal environments. The objective of this program was to demonstrate the technical feasibility of the 'tile' array packaging architecture at EHF via the insertion of 1990 MMIC technology into a functional tile array or subarray module. The means test of this objective was to demonstrate and deliver to NASA a minimum of two 4 x 4 (16 radiating element) subarray modules operating in a transmit mode at 29.6 GHz. Available (1990) MMIC technology was chosen to focus the program effort on the novel interconnect schemes and packaging requirements rather than focusing on MMIC development. Major technical achievements of this program include the successful integration of two 4 x 4 subarray modules into a single antenna array. This 32 element array demonstrates a transmit EIRP of over 300 watts yielding an effective directive power gain in excess of 55 dB at 29.63 GHz. The array has been actively used as the transmit link in airborne/terrestrial mobile communication experiments accomplished via the ACTS satellite launched in August 1993.

Enhancing Students' Socialization: Key Elements. ERIC Digest.

ERIC Educational Resources Information Center

Brophy, Jere

Coping with students who display social adjustment problems can be frustrating. However, teachers can take actions toward minimizing classroom conflicts by socializing students into a classroom environment conducive to learning. Modeling prosocial behavior is the most basic element for enhancing student socialization. In situations in which…

Towards a Social History of Technological Ideas: Joseph Black, James Watt, and the Separate Condenser. An Occasional Paper on Man/Society/Technology.

ERIC Educational Resources Information Center

Donovan, Arthur

This seminar paper explores the role that historians of technology can play in the reevaluation of the relationship between technical and social change. Historians of technology need to ask questions about the nontechnological aspects of society which have influenced technical change in the past. In the realm of ideas, historians should check…

Changes in Aspects of Students' Self-Reported Personal, Social and Technical Skills during a Six-Week Wilderness Expedition in Arctic Greenland

ERIC Educational Resources Information Center

Stott, Tim; Hall, Neil

2003-01-01

This investigation focuses on students' self-reported changes in personal, social and technical skills that took place during a six-week long expedition to East Greenland. A 105-item pre-and post-expedition questionnaire was completed by 60 young expeditioners aged 16 to 20. Before the expedition participants generally felt that they had high…

The Significance of Social Relationships in Learning to Become a Vocational and Technical Education Teacher: A Case Study of Three Individuals

ERIC Educational Resources Information Center

Goh, Adeline Yuen Sze

2013-01-01

This article about workplace learning examines the learning of individuals in becoming a Vocational and Technical Education (VTE) teacher in Brunei. Drawing on research findings from a group of student teachers, it presents case study accounts of three individuals to illustrate the importance of social relationships in learning to become a VTE…

ALEGRA -- A massively parallel h-adaptive code for solid dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Summers, R.M.; Wong, M.K.; Boucheron, E.A.

1997-12-31

ALEGRA is a multi-material, arbitrary-Lagrangian-Eulerian (ALE) code for solid dynamics designed to run on massively parallel (MP) computers. It combines the features of modern Eulerian shock codes, such as CTH, with modern Lagrangian structural analysis codes using an unstructured grid. ALEGRA is being developed for use on the teraflop supercomputers to conduct advanced three-dimensional (3D) simulations of shock phenomena important to a variety of systems. ALEGRA was designed with the Single Program Multiple Data (SPMD) paradigm, in which the mesh is decomposed into sub-meshes so that each processor gets a single sub-mesh with approximately the same number of elements. Usingmore » this approach the authors have been able to produce a single code that can scale from one processor to thousands of processors. A current major effort is to develop efficient, high precision simulation capabilities for ALEGRA, without the computational cost of using a global highly resolved mesh, through flexible, robust h-adaptivity of finite elements. H-adaptivity is the dynamic refinement of the mesh by subdividing elements, thus changing the characteristic element size and reducing numerical error. The authors are working on several major technical challenges that must be met to make effective use of HAMMER on MP computers.« less

Report by the Aerospace Safety Advisory Panel

NASA Technical Reports Server (NTRS)

1981-01-01

The process of preparation for the first two shuttle flights was observed and information from both flights was gathered in order to confirm the concept and performance of the major elements of the space transportation system. To achieve truly operational operating safety, regularity, and minimum practical cost, the organization of efforts between the R&D community and any transportation service organization should be clearly separated with the latter organization assuming responsibilities for marketing its services; planning and acquiring prime hardware and spares; maintainance; certification of procedures; training; and creation of requirements for future development. A technical audit of the application of redundancy concepts to shuttle systems is suggested. The state of the art of space transportation hardware suggests that a number of concept changes may improve reliability, costs, and operational safety. For the remaining R&D flights, it is suggested that a redline audit be made of limits that should not be exceeded for ready to launch.

Fourier-Accelerated Nodal Solvers (FANS) for homogenization problems

NASA Astrophysics Data System (ADS)

Leuschner, Matthias; Fritzen, Felix

2017-11-01

Fourier-based homogenization schemes are useful to analyze heterogeneous microstructures represented by 2D or 3D image data. These iterative schemes involve discrete periodic convolutions with global ansatz functions (mostly fundamental solutions). The convolutions are efficiently computed using the fast Fourier transform. FANS operates on nodal variables on regular grids and converges to finite element solutions. Compared to established Fourier-based methods, the number of convolutions is reduced by FANS. Additionally, fast iterations are possible by assembling the stiffness matrix. Due to the related memory requirement, the method is best suited for medium-sized problems. A comparative study involving established Fourier-based homogenization schemes is conducted for a thermal benchmark problem with a closed-form solution. Detailed technical and algorithmic descriptions are given for all methods considered in the comparison. Furthermore, many numerical examples focusing on convergence properties for both thermal and mechanical problems, including also plasticity, are presented.

Factors that Influence Women's Technical Skill Development in Outdoor Adventure

ERIC Educational Resources Information Center

Warren, Karen; Loeffler, TA

2006-01-01

This article provides a theoretical foundation for understanding women's technical skill development (TSD) in outdoor adventure. An examination of societal and biological factors influencing women's TSD focuses on gender role socialization, sense of competence, technical conditioning, sexism, spatial ability, and risk-taking. The article suggests…

77 FR 40026 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-06

... and contractor logistics, Quality Assurance Team support services, engineering and technical support..., engineering and technical support, and other related elements of program support. The estimated cost is $49..., maintenance, or training is Confidential. Reverse engineering could reveal Confidential information...

Vehicle infrastructure integration proof of concept : technical description--vehicle : final report

DOT National Transportation Integrated Search

2009-05-19

This report provides the technical description of the VII system developed for the Cooperative Agreement VII Program between the USDOT and the VII Consortium. The basic architectural elements are summarized and detailed descriptions of the hardware a...

The Future Cybersecurity Workforce: Going Beyond Technical Skills for Successful Cyber Performance

PubMed Central

Dawson, Jessica; Thomson, Robert

2018-01-01

One of the challenges in writing an article reviewing the current state of cyber education and workforce development is that there is a paucity of quantitative assessment regarding the cognitive aptitudes, work roles, or team organization required by cybersecurity professionals to be successful. In this review, we argue that the people who operate within the cyber domain need a combination of technical skills, domain specific knowledge, and social intelligence to be successful. They, like the networks they operate, must also be reliable, trustworthy, and resilient. Defining the knowledge, skills, attributes, and other characteristics is not as simple as defining a group of technical skills that people can be trained on; the complexity of the cyber domain makes this a unique challenge. There has been little research devoted to exactly what attributes individuals in the cyber domain need. What research does exist places an emphasis on technical and engineering skills while discounting the important social and organizational influences that dictate success or failure in everyday settings. This paper reviews the literature on cyber expertise and cyber workforce development to identify gaps and then argues for the important contribution of social fit in the highly complex and heterogenous cyber workforce. We then identify six assumptions for the future of cybersecurity workforce development, including the requirement for systemic thinkers, team players, a love for continued learning, strong communication ability, a sense of civic duty, and a blend of technical and social skill. Finally, we make recommendations for social and cognitive metrics which may be indicative of future performance in cyber work roles to provide a roadmap for future scholars. PMID:29946276

Experiments on Socio-Technical Systems: The Problem of Control.

PubMed

Kroes, Peter

2016-06-01

My aim is to question whether the introduction of new technologies in society may be considered to be genuine experiments. I will argue that they are not, at least not in the sense in which the notion of experiment is being used in the natural and social sciences. If the introduction of a new technology in society is interpreted as an experiment, then we are dealing with a notion of experiment that differs in an important respect from the notion of experiment as used in the natural and social sciences. This difference shows itself most prominently when the functioning of the new technological system is not only dependent on technological hardware but also on social 'software', that is, on social institutions such as appropriate laws, and actions of operators of the new technological system. In those cases we are not dealing with 'simply' the introduction of a new technology, but with the introduction of a new socio-technical system. I will argue that if the introduction of a new socio-technical system is considered to be an experiment, then the relation between the experimenter and the system on which the experiment is performed differs significantly from the relation in traditional experiments in the natural and social sciences. In the latter experiments it is assumed that the experimenter is not part of the experimental system and is able to intervene in and control the experimental system from the outside. With regard to the introduction of new socio-technical systems the idea that there is an experimenter outside the socio-technical system who intervenes in and controls that system becomes problematic. From that perspective we are dealing with a different kind of experiment.

Risk communication and the Precautionary Principle.

PubMed

Biocca, Marco

2004-01-01

The perception of risks for environment and health deriving from globalization processes and an uncontrolled use of modern technologies is growing everywhere. The greater the capacity of controlling living conditions, the larger is the possibility of misusing this power. In environmental and occupational health research we tend to reduce the complexity of the observed phenomena in order to facilitate conclusions. In social and political sciences complexity is an essential element of the context, which needs to be continuously considered. The Precautionary Principle is a tool for facing complexity and uncertainty in health risk management. This paper is aimed at demonstrating that this is not only a problem of technical risk assessment. Great attention should also be paid to improve risk communication. Communication between the stakeholders (experts, decision makers, political and social leaders, media, groups of interest and people involved) is possibly the best condition to be successful in health risk management. Nevertheless, this process usually runs up against severe obstacles. These are not only caused by existing conflicts of interest. Differences in values, languages, perceptions, resources to have access to information, and to express one's own point of view are other key aspects.

The Main Portal of the Cathedral of Monreale: First Geometric Analysis and Interpretive Assessment of Architectural Features

NASA Astrophysics Data System (ADS)

Lo Brutto, M.; Dardanelli, G.; Ebolese, D.; Milazzo, G.; Pipitone, C.; Sciortino, R.

2017-05-01

Nowadays, 3D documentation of architectural assets is becoming a demanding task for the valorisation of Cultural Heritage especially after a restoration project. The 3D documentation can be used for detailed analysis of specific elements, for monitoring the state of conservation and for valorisation actions. The paper describes the results of the 3D close-range photogrammetry survey of the main portal of the Cathedral of Monreale (Palermo, Italy). The Cathedral is one the most important monumental complexes in Sicily that, for its high historical and artistic importance has been inscribed on UNESCO's World Heritage List since 2015. The main portal of the Cathedral has been recently restored. The restoration work has given the opportunity to evidence small details of the sculptural decorations and to carry out new interpretative analysis of the bas-reliefs. The main purpose of the work is to obtain a detailed 3D model and a high-resolution ortophoto of the entire portal and of some architectural details. The study was used to evaluate the most appropriate technical solutions for the 3D survey and to define the most suitable parameters for image acquisition and data processing.

Identifying Mental Health Elements among Technical University Students Using Fuzzy Delphi Method

NASA Astrophysics Data System (ADS)

Pua, P. K.; Lai, C. S.; Lee, M. F.

2017-08-01

Mental health is a part of our daily life that is often experienced. As a student, mental health issue often encounters a variety of difficult challenges at the higher education institution. A student with good mental health can handle and cope the normal stress of life, capable work productivity, enhance academic performance and able to make contribute to the community. However, rapidly transformation and changing of society have been impacted on students’ mental health, and it will be deteriorated and negatively impact on students if it absence of preventive controlled. This study aimed to identify the element of mental health among the technical university students. A total of 11 experts were selected to analyze the fuzziness consensus of experts. All collected data was analyzed by using the fuzzy Delphi method and the result shows that there are 4 elements of 8 elements that fulfill the requirement consensus of experts, which threshold value is equal and less than 0.2, the percentage of the expert group is more than 75%. The four elements were depression, anxiety, stress, and fear are often experienced by technical university students. In conclusion, precocious actions have to be taken by university and counseling center, parents and non-government organization in order to mitigate the mental health problem faced by students to improve the quality lifestyle students at the university.

Design Issues for Producing Effective Multimedia Presentations.

ERIC Educational Resources Information Center

Mason, Lisa D.

1997-01-01

Discusses design issues for interactive multimedia. Notes that technical communication instructors must consider navigational aids, the degree of control a user should have, audio cues, color and typographical elements, visual elements, and copyright issues. (RS)

Audit Report on "Work for Others Performed by the Department of Energy for the Department of Defense"

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Pursuant to the Atomic Energy Act of 1954, as amended, and the Economy Act of 1932, the Department of Energy and its semi-autonomous National Nuclear Security Administration (NNSA) provide research and technical assistance to other Federal agencies on a reimbursable, full cost recovery basis through the Work for Others (WFO) program. For the vast majority of WFO technical projects, Department Federal officials furnish administrative project oversight while the actual detailed scientific or technical work is completed by the Department's 'management and operating' contractors. These contractors are awarded a special contract type specifically created under the Federal Acquisition Regulation to managemore » and operate Department sites and facilities, including sophisticated laboratories and technical centers, on a government-owned, contractor-operated basis. With annual expenditures exceeding $1 billion, the Department of Defense (DoD) is one of the Department's largest WFO customers. Work performed for DoD at the Department's national laboratories and other facilities includes highly technical research in areas such as nuclear weapons systems, counter-terrorism, and in-theater troop support. The National Defense Authorization Act for Fiscal Year (FY) 2009, required the Inspectors General of the DoD and the Department to review procurement methods to determine whether the Department complied with DoD procurement requirements and/or whether alternative procurement policies were in place. In response, we focused our review on projects performed by NNSA because it completes the vast majority (approximately $900 million in FY 2008) of the Department's work for DoD. As part of this effort, and, at the specific request of the DoD Office of Inspector General (DoD OIG), we identified the universe of WFO technical projects that received new funding in the fourth quarter of FY 2008 at NNSA sites. We independently reviewed a judgmental sample of 11 projects selected by the DoD OIG to meet the objectives of this audit. Our review revealed that NNSA managed DoD WFO technical projects in a manner consistent with requirements of the Atomic Energy Act of 1954, the Federal Acquisition Regulation, and the Department's implementing guidance, the Department of Energy Acquisition Regulation. Because of the very nature of the Department's management and operating contracting model, WFO projects may not be technically compliant with DoD procurement regulations in certain instances. We found that NNSA did not let new contracts or task orders for the DoD WFO technical projects we reviewed and instead managed them under its existing internal control process as part of its management and operating contract structure. In one instance, we noted that the Department had, at DoD's request, supplemented its control structure to incorporate specific DoD procurement requirements. Senior Department of Energy procurement officials acknowledged that neither the Department nor NNSA modified their existing prime contracts to incorporate specific defense procurement requirements because such modifications would be inappropriate, costly, and inefficient. In short, they informed us that the Department had developed and implemented a series of controls designed to monitor overall contractor performance, including WFO technical projects. Department and NNSA officials noted, however, that they were willing to incorporate DoD specific requirements into work orders should DoD request and fund such efforts. Additional details regarding management of WFO technical projects are discussed in the body of this report.« less

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 22: US academic librarians and technical information specialists as information intermediaries: Results of the phase 3 survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis U.S. academic librarians and technical information specialists as information intermediaries.

Training Aids for Basic Combat Skills: A Video Feedback System

DTIC Science & Technology

2011-05-01

U.S. Army Research Institute for the Behavioral and Social Sciences Research Report 1945 Training Aids for Basic Combat...Training Aids for Basic Combat Skills: A Video Feedback System 5a. CONTRACT OR GRANT NUMBER W74V8H-04-D-0045 (DO #0034) 5b. PROGRAM ELEMENT...Subject Matter POC: Martin L. Bink 14. ABSTRACT (Maximum 200 words): The overarching goal was to develop a training aid that could be used by

DoD Program for Stability of Civilian Employment: Policies, Procedures, and Programs Manual

DTIC Science & Technology

1990-09-01

employment outside the labor market area of the releasing activity and who elect to have the movement of household goods at the expense of the Federal...other local media . 2. Providing an informational service to the workforce, including remote serviced activities, to reinstatement eligibles, and to...program in which they are to be entered. Starting with the Social Security Number, each element of information on the form is preceded by a number in

Operational Level Air Commanders: A Search for the Elements of Genius

DTIC Science & Technology

1994-06-01

courage in the face of moral danger. This is also referred to as courage d’espirit. Richard Simpkin, author of Race to the Swift, identifies this as the...enemy’s political, military, economic or social infrastructure.83 Group Captain Andrew Vallance of the Royal Air Force asserts that �airpower has...Finally, Vallance suggests that airpower has some conditional characteristics. The first such characteristic is that of depending on bases. If your

Nation Building as a Determinent of Economic Growth

DTIC Science & Technology

2010-05-18

Consortium for Political and Social Reserch (2007). Mankiw , N. Gregory, David Romer, and David N. Weil. “A Contribution to the Empirics of Economic Growth...Determinent of Economic Growth 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6 . AUTHOR(S) 5d. PROJECT NUMBER Creasey. Ellyn Ann 5e. TASK NUMBER 51...J ss istance and econom ic aid impact the development process. The primary resu lts suggest a 1% increase in spending on nation building result s

High Productivity Aluminum Manufacturing

DTIC Science & Technology

2013-07-01

D. J. Spinella Alcoa Inc. Alcoa Technical Center 100 Technical Drive Alcoa Center, PA 15069 July 2013 CNST Base Task Order...Myers, Kirit Shah, D. J. Spinella 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Alcoa , Inc...8. PERFORMING ORGANIZATION REPORT NUMBER 100 Technical Drive Alcoa Center, PA 15069 9

Consortia Formation and Characteristics under the "Carl D. Perkins Career and Technical Education Act of 2006"

ERIC Educational Resources Information Center

Staklis, Sandra; Klein, Steve

2014-01-01

The "Carl D. Perkins Career and Technical Education Act of 2006" ("Perkins IV") sets a minimum allocation requirement that secondary and postsecondary career and technical education (CTE) subgrantees must achieve to receive federal financing. An eligible recipient with an allocation below the funding threshold may obtain a…

Small sample estimation of the reliability function for technical products

NASA Astrophysics Data System (ADS)

Lyamets, L. L.; Yakimenko, I. V.; Kanishchev, O. A.; Bliznyuk, O. A.

2017-12-01

It is demonstrated that, in the absence of big statistic samples obtained as a result of testing complex technical products for failure, statistic estimation of the reliability function of initial elements can be made by the moments method. A formal description of the moments method is given and its advantages in the analysis of small censored samples are discussed. A modified algorithm is proposed for the implementation of the moments method with the use of only the moments at which the failures of initial elements occur.

Discriminating utopian from dystopian literature: Why is walden two considered a dystopia?

PubMed Central

Newman, Bobby

1993-01-01

Skinner thought of Walden Two as a utopia, but many literary critics consider it a dystopia. The present paper examines works by several authors of utopian literature in an effort to determine what elements lead critics to classify works as “dystopian.” Common elements seem to include (a) suspicion of scientific social planning, (b) the unhappiness of the characters portrayed, (c) suspicion of sources of control of behavior outside the individual, (d) violation of a presumed inherent need to struggle, and (e) suspicion of behavioral methods of governance. The elements Walden Two shares with other utopias and dystopias are examined, and the conclusion is offered that Walden Two could not be considered a dystopia for any of the traditional reasons. Instead, the negative view of Walden Two seems to be an outgrowth of literary devices and general negative reactions to behavioral determinism. PMID:22478144

Chinese Scientific and Technical Information Institutions: Development and Perspective

ERIC Educational Resources Information Center

Yanning, Zheng

2011-01-01

The collection, storage, processing, and dissemination of scientific and technical information make an important basis for economic and social development as well as for scientific development. A nation has to develop the right mechanisms and modalities to collect, store, process, and disseminate scientific and technical information tailored to…

Placing Tactical Data into the MIST and LC2IEDM Systems

DTIC Science & Technology

2003-10-01

Defence R& D Canada DEFENCE DÉFENSE & Placing Tactical Data into the MIST and LC2IEDM Systems Anthony W. Isenor Technical Memorandum DRDC Atlantic TM...intentionally left blank. Copy No: Placing Tactical Data into the MIST and LC2IEDM Systems Anthony W. Isenor Defence R& D Canada – Atlantic Technical...currently underway at Defence R& D Canada – Atlantic, as well as international efforts with The Technical Cooperation Program (TTCP). Both groups

Steels For Rolling-Element Bearings

NASA Technical Reports Server (NTRS)

Zaretsky, Erwin V.

1988-01-01

Bearing lives increased by attention to details of processing and applications. NASA technical memorandum discusses selection of steels for long-life rolling-element bearings. After brief review of advances in manufacturing, report discusses effect of cleanliness of bearing material on fatigue in rolling element. Also discusses fracture toughnesses of through-hardened and case-hardened materials.

Technical Elements, Demonstration Projects, and Fiscal Models in Medicaid Managed Care for People with Developmental Disabilities.

ERIC Educational Resources Information Center

Kastner, Theodore A.; Walsh, Kevin K.; Criscione, Teri

1997-01-01

Presents a general model of the structure and functioning of managed care and describes elements (provider networks, fiscal elements, risk estimation, case-mix, management information systems, practice parameters, and quality improvement) critical to people with developmental disabilities. Managed care demonstration projects and a hypothetical…

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

42 CFR 56.703 - Project elements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Project elements. 56.703 Section 56.703 Public... SERVICES Grants for Technical Assistance § 56.703 Project elements. A project for the provision of.... (c) Where the project will provide training to the staff of a center or entity in management or the...

Formative Evaluation of a Sociotechnical System Intervention at an Army Maintenance Depot

DTIC Science & Technology

1986-07-01

periodically reassess itself to determine if the balance between the technical and social systems remains adaptive and responsive to the requirements...developed a comprehensive set of recommendations for improving the balance between the social and technical systems of the depot. During 1983, most of...ity and quality of worklife . However, the nature and extent of the impact is highly elusive and resistant to quantification. 1-4 FORMATIVE

Equal Opportunity Leadership Training for Company-Level Chain of Command

DTIC Science & Technology

1981-01-01

Relations/ Equal Opportunity Training in USAREUR, ARI Technical Report TR-78-B10, Alexandria, Va.: US. Army Research Institute for the Behavioral and Social ...Behavioral and Social Sciences, 1978. Marcia A. Gilbert and Peter G. Nordlie, An Analysis of Race Relations/ Equal Opportunity Training in USAREUR, ARI...Technical Report 534 - EQUAL OPPORTUNITY LEADERSHIP TRAINING FOR COMPANY-LEVEL CHAIN OF COMMAND Dale K. Brown, Silas J. White, Exequiel R. Sevilla

Application of the Rehabilitation Act Section 508 to the NPFC

DOT National Transportation Integrated Search

2001-04-09

This paper provides a brief summary of Section 508 and its associated technical standards in layman's terms. It identifies the elements of the NPFC information technology (IT) that are affected by the technical standards and a brief discussion of how...

Safety Education--An Essential Element of Technical Training

ERIC Educational Resources Information Center

Glazener, Everett R.; Comstock, Thomas W.

1978-01-01

After tracing the background of the safety movement, provisions of recent safety legislation, and the ecological and environmental impact of industrial processes, the author stresses the need for safety education in technical education programs to prepare future employees for industrial safety requirements. (MF)

78 FR 78939 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... Quantity or Quantities of Articles or Services under Consideration for Purchase: C-130J technical, engineering and software support; software updates and patches; familiarization training for Portable Flight... and contractor technical support services; and other related elements of logistics and program support...

Flood warnings in coastal areas: how do experience and information influence responses to alert services?

NASA Astrophysics Data System (ADS)

Pescaroli, G.; Magni, M.

2015-04-01

Many studies discuss the economic and technical aspects of flood warnings. Less attention has been given to the social and behavioural patterns that affect alert services. In particular, the literature focuses on warnings activated in river basins or marine environments without providing clear evidence on Mediterranean coastal areas, even though these are subjected to growing flood risk related to climate change. This paper is a first attempt to bridge this gap. Our research develops an in-depth analysis of the village of Cesenatico on the Adriatic Sea coast. Here the municipality adopted two complementary warning systems: a siren and an alert via short message service (SMS). The analysis focuses on a survey conducted in 2011 and 2012 with 228 participants. The relationships between social and behavioural variables and warning services are investigated as well as flood preparedness and information dissemination. Qualitative evidence from informal interviews is used to support the understanding of key responses. The conclusions show how different social and behavioural patterns can influence the effectiveness and use of warning systems, regardless of the technology adopted and the structural mitigation measures implemented. Education, training and accountability are seen to be critical elements for implementation. Finally, the statistical output is used to suggest new questions and new directions for research.

Toward Information Infrastructure Studies: Ways of Knowing in a Networked Environment

NASA Astrophysics Data System (ADS)

Bowker, Geoffrey C.; Baker, Karen; Millerand, Florence; Ribes, David

This article presents Information Infrastructure Studies, a research area that takes up some core issues in digital information and organization research. Infrastructure Studies simultaneously addresses the technical, social, and organizational aspects of the development, usage, and maintenance of infrastructures in local communities as well as global arenas. While infrastructure is understood as a broad category referring to a variety of pervasive, enabling network resources such as railroad lines, plumbing and pipes, electrical power plants and wires, this article focuses on information infrastructure, such as computational services and help desks, or federating activities such as scientific data repositories and archives spanning the multiple disciplines needed to address such issues as climate warming and the biodiversity crisis. These are elements associated with the internet and, frequently today, associated with cyberinfrastructure or e-science endeavors. We argue that a theoretical understanding of infrastructure provides the context for needed dialogue between design, use, and sustainability of internet-based infrastructure services. This article outlines a research area and outlines overarching themes of Infrastructure Studies. Part one of the paper presents definitions for infrastructure and cyberinfrastructure, reviewing salient previous work. Part two portrays key ideas from infrastructure studies (knowledge work, social and political values, new forms of sociality, etc.). In closing, the character of the field today is considered.

International ultraviolet explorer observatory operations

NASA Technical Reports Server (NTRS)

1986-01-01

This volume contains the Final Report for the International Ultraviolet Explorer (IUE) Observatory Operations contract, NAS5-28787. The report summarizes the activities of the IUE Observatory over the 13-month period from November 1985 through November 1986 and is arranged in sections according to the functions specified in the Statement of Work (SOW) of the contract. In order to preserve numerical correspondence between the technical SOW elements specified by the contract and the sections of this report, project management activities (SOW element 0.0.) are reported here in Section 7, following the reports of technical SOW elements 1.0 through 6.0. Routine activities have been summarized briefly whenever possible; statistical compilations, reports, and more lengthy supplementary material are contained in the Appendices.

The pioneer projects: Economical exploration of the solar system

NASA Technical Reports Server (NTRS)

Spahr, J. R.; Hall, C. F.

1975-01-01

The interplanetary Pioneer missions are reviewed in terms of management implications and cost control. The responsibilities, organizational structure, and management practices of the Pioneer Projects are presented. The lines of authority and areas of responsibility of the principal organizational elements supporting the Pioneer missions are identified, and the methods employed for maintaining effective and timely interactions among these elements are indicated. The technical and administrative functions of the various organizational elements of the Pioneer Project Office at Ames Research Center are described in terms of their management responsibilities and interactions with other elements of the Project Office and with external organizations having Pioneer Project responsibilities. The management and control of activities prior to and during the hardware procurement phase are described to indicate the basis for obtaining visibility of the technical progress, utilization of resources, and cost performance of the contractors and other institutions supporting the Pioneer projects.

Satellite power system concept development and evaluation program. Volume 1: Technical assessment summary report

NASA Technical Reports Server (NTRS)

1980-01-01

Candidate satellite power system (SPS) concepts were identified and evaluated in terms of technical and cost factors. A number of alternative technically feasible approaches and system concepts were investigated. A reference system was defined to facilitate economic, environmental, and societal assessments by the Department of Energy. All elements of the reference system were defined including the satellite and all its subsystems, the orbital construction and maintenance bases, all elements of the space transportation system, the ground receiving station, and the associated industrial facilities for manufacturing the required hardware. The reference conclusions and remaining issues are stated for the following topical areas: system definition; energy conversion and power management; power transmission and reception; structures, controls, and materials; construction and operations; and space transportation.

Report on the technical review workshop on the reference dose for Aroclor 1016. Held in Washington, DC on May 24-25, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1994-11-01

The report includes information and material from a technical review workshop organized by the U.S. Environmental Protection Agency`s (EPA`s) Risk Assessment Forum for EPA`s Reference Dose/Reference Concentration (RfD/RfC) Work Group. The meeting was held in Washington, DC, at the Barcelo Washington Hotel on May 24-25, 1994. The subject of the technical review was the Integrated Risk Information System (IRIS) RfD entry for Aroclor 1016, a polychlorinated biphenyl (PCB). The expert technical review panel was convened to independently evaluate whether the RfD for Aroclor 1016 is based on a scientifically responsible analysis that represents full consideration of the available data andmore » clean articulation of that analysis in the IRIS RfD entry. EPA also requested panel members to consider four broad options for the Aroclor 1016 RfD as potential recommendations to the RfD/RfC Work Group.« less

Anticipatory ethics for a future Internet: analyzing values during the design of an Internet infrastructure.

PubMed

Shilton, Katie

2015-02-01

The technical details of Internet architecture affect social debates about privacy and autonomy, intellectual property, cybersecurity, and the basic performance and reliability of Internet services. This paper explores one method for practicing anticipatory ethics in order to understand how a new infrastructure for the Internet might impact these social debates. This paper systematically examines values expressed by an Internet architecture engineering team-the Named Data Networking project-based on data gathered from publications and internal documents. Networking engineers making technical choices also weigh non-technical values when working on Internet infrastructure. Analysis of the team's documents reveals both values invoked in response to technical constraints and possibilities, such as efficiency and dynamism, as well as values, including privacy, security and anonymity, which stem from a concern for personal liberties. More peripheral communitarian values espoused by the engineers include democratization and trust. The paper considers the contextual and social origins of these values, and then uses them as a method of practicing anticipatory ethics: considering the impact such priorities may have on a future Internet.

Diverse knowledges and competing interests: an essay on socio-technical problem-solving.

PubMed

di Norcia, Vincent

2002-01-01

Solving complex socio-technical problems, this paper claims, involves diverse knowledges (cognitive diversity), competing interests (social diversity), and pragmatism. To explain this view, this paper first explores two different cases: Canadian pulp and paper mill pollution and siting nuclear reactors in systematically sensitive areas of California. Solving such socio-technically complex problems involves cognitive diversity as well as social diversity and pragmatism. Cognitive diversity requires one to not only recognize relevant knowledges but also to assess their validity. Finally, it is suggested, integrating the resultant set of diverse relevant and valid knowledges determines the parameters of the solution space for the problem.

Tracking the mutual shaping of the technical and social dimensions of solar-powered mosquito trapping systems (SMoTS) for malaria control on Rusinga Island, western Kenya.

PubMed

Oria, Prisca A; Hiscox, Alexandra; Alaii, Jane; Ayugi, Margaret; Mukabana, Wolfgang Richard; Takken, Willem; Leeuwis, Cees

2014-11-18

There has been increasing effort in recent years to incorporate user needs in technology design and re-design. This project employed a bottom-up approach that engaged end users from the outset. Bottom-up approaches have the potential to bolster novel interventions and move them towards adaptive and evidence-based strategies. The present study concerns an innovative use of solar-powered mosquito trapping systems (SMoTS) to control malaria in western Kenya. Our paper highlights the co-dependence of research associated with the development of the SMoTS technology on one hand and research for enhancing the sustainable uptake of that very same intervention within the community on the other. During the pre-intervention year, we examined the design, re-design and piloting of a novel technology to generate lessons for malaria elimination on Rusinga Island. Initial ideas about many technological necessities were evaluated and re-designed following feedback from various sources, including technical and social research as well as broader interactions with the social environment. We documented the interlocking of the multiple processes and activities that took place through process observation and document reviews. We analysed the data within the conceptual framework of system innovation by identifying mutual shaping between technical and social factors. Our findings illustrate how various project stakeholders including project staff, collaborators, donor, and community members simultaneously pursued interdependent technological transformations and social interests. In the ongoing process, we observed how partial outcomes in the technological domain influenced social events at a later phase and vice versa. Looking at malaria intervention projects employing novel technologies as niches that may evolve towards system innovation, helps to reveal interrelations between the various technical and social aspects. Revealing these interrelations requires a different role for research and different perspective on innovation where innovation is more than the technical aspects. This approach therefore requires that research is designed in a way that enables obtaining feedback from both aspects.

Genetic Basis of Melanin Pigmentation in Butterfly Wings

PubMed Central

Zhang, Linlin; Martin, Arnaud; Perry, Michael W.; van der Burg, Karin R. L.; Matsuoka, Yuji; Monteiro, Antónia; Reed, Robert D.

2017-01-01

Despite the variety, prominence, and adaptive significance of butterfly wing patterns, surprisingly little is known about the genetic basis of wing color diversity. Even though there is intense interest in wing pattern evolution and development, the technical challenge of genetically manipulating butterflies has slowed efforts to functionally characterize color pattern development genes. To identify candidate wing pigmentation genes, we used RNA sequencing to characterize transcription across multiple stages of butterfly wing development, and between different color pattern elements, in the painted lady butterfly Vanessa cardui. This allowed us to pinpoint genes specifically associated with red and black pigment patterns. To test the functions of a subset of genes associated with presumptive melanin pigmentation, we used clustered regularly interspaced short palindromic repeats (CRISPR)/Cas9 genome editing in four different butterfly genera. pale, Ddc, and yellow knockouts displayed reduction of melanin pigmentation, consistent with previous findings in other insects. Interestingly, however, yellow-d, ebony, and black knockouts revealed that these genes have localized effects on tuning the color of red, brown, and ochre pattern elements. These results point to previously undescribed mechanisms for modulating the color of specific wing pattern elements in butterflies, and provide an expanded portrait of the insect melanin pathway. PMID:28193726

Mobilizing women for minority health and social justice in california.

PubMed

Littlefield, Diane; Robison, Connie Chan; Engelbrecht, Luz; González, Belma; Hutcheson, Heather

2002-04-01

Women's Health Leadership is building the leadership capacity of diverse community leaders in California committed to promoting health and social justice in their communities. This program provides opportunities for cross-cultural exchanges of ideas, resources, and expertise. Graduates continue to receive technical support and to engage in peer learning via an alumnae network. The network is dedicated to advancing social justice issues and to addressing health disparities. It is also a way to mobilize trained grassroots leaders to provide expertise to influence policy decisions, to provide technical support and resources to local communities, and to foster new partnerships across the state.

National Technical Assistance Systems in Special Education.

ERIC Educational Resources Information Center

Reynolds, Maynard C., Ed.

Presented are 17 papers and a summary from the 1974 conference on National Technical Assistance Systems in Special Education. Included are presentations by the following participants: J. Gallagher, D. Stedman, D. Lillie and T. Black, D. Davies, E. Deno, J. McCarthy, D. Jackson, K. Lundholm, J. Chalfant, R. Johnson et al., P. Mann, W. Korba, R.…

Visual method for detecting critical damage in railway contact strips

NASA Astrophysics Data System (ADS)

Judek, S.; Skibicki, J.

2018-05-01

Ensuring an uninterrupted supply of power in the electric traction is vital for the safety of this important transport system. For this purpose, monitoring and diagnostics of the technical condition of the vehicle’s power supply elements are becoming increasingly common. This paper presents a new visual method for detecting contact strip damage, based on measurement and analysis of the movement of the overhead contact line (OCL) wire. A measurement system configuration with a 2D camera was proposed. The experimental method has shown that contact strips damage can be detected by transverse displacement signal analysis. It has been proven that the velocity signal numerically established on that basis has a comparable level in the case of identical damage, regardless of its location on the surface of the contact strip. The proposed method belongs to the group of contact-less measurements, so it does not require interference with the structure of the catenary network nor the mounting of sensors in its vicinity. Measurement of displacements of the contact wire in 2D space makes it possible to combine the functions of existing diagnostic stands assessing the correctness of the mean contact force control adjustment of the current collector with the elements of the contact strip diagnostics, which involves detecting their damage which may result in overhead contact line rupture.

A Call to Action to Bring Safer Parenteral Micronutrient Products to the U.S. Market.

PubMed

Vanek, Vincent W; Borum, Peggy; Buchman, Alan; Fessler, Theresa A; Howard, Lyn; Shenkin, Alan; Valentine, Christina J

2015-08-01

The American Society for Parenteral and Enteral Nutrition (A.S.P.E.N.) started an intensive review of commercially available parenteral vitamin and trace element (TE) products in 2009. The chief findings were that adult multi-TE products currently available in the United States (U.S.) provide potentially toxic amounts of manganese, copper, and chromium, and neonatal/pediatric multi-TE products provide potentially toxic amounts of manganese and chromium. The multivitamin products appeared safe and effective; however, a separate parenteral vitamin D product is needed for those patients on standard therapy who continue to be vitamin D depleted and are unresponsive to oral supplements. The review process also extended to parenteral choline and carnitine. Although choline and carnitine are not technically vitamins or trace elements, choline is an essential nutrient in all age groups, and carnitine is an essential nutrient in infants, according to the Food and Nutrition Board of the Institute of Medicine. A parenteral choline product needs to be developed and available. Efforts are currently under way to engage the U.S. Food and Drug Administration (FDA) and the parenteral nutrient industry so A.S.P.E.N.'s recommendations can become a commercial reality. © 2015 American Society for Parenteral and Enteral Nutrition.

Columbia Accident Investigation Board Report. Volume Two

NASA Technical Reports Server (NTRS)

Barry, J. R.; Jenkins, D. R.; White, D. J.; Goodman, P. A.; Reingold, L. A.

2003-01-01

Volume II of the Report contains appendices that were cited in Volume I. The Columbia Accident Investigation Board produced many of these appendices as working papers during the investigation into the February 1, 2003 destruction of the Space Shuttle Columbia. Other appendices were produced by other organizations (mainly NASA) in support of the Board investigation. In the case of documents that have been published by others, they are included here in the interest of establishing a complete record, but often at less than full page size. Contents include: CAIB Technical Documents Cited in the Report: Reader's Guide to Volume II; Appendix D. a Supplement to the Report; Appendix D.b Corrections to Volume I of the Report; Appendix D.1 STS-107 Training Investigation; Appendix D.2 Payload Operations Checklist 3; Appendix D.3 Fault Tree Closure Summary; Appendix D.4 Fault Tree Elements - Not Closed; Appendix D.5 Space Weather Conditions; Appendix D.6 Payload and Payload Integration; Appendix D.7 Working Scenario; Appendix D.8 Debris Transport Analysis; Appendix D.9 Data Review and Timeline Reconstruction Report; Appendix D.10 Debris Recovery; Appendix D.11 STS-107 Columbia Reconstruction Report; Appendix D.12 Impact Modeling; Appendix D.13 STS-107 In-Flight Options Assessment; Appendix D.14 Orbiter Major Modification (OMM) Review; Appendix D.15 Maintenance, Material, and Management Inputs; Appendix D.16 Public Safety Analysis; Appendix D.17 MER Manager's Tiger Team Checklist; Appendix D.18 Past Reports Review; Appendix D.19 Qualification and Interpretation of Sensor Data from STS-107; Appendix D.20 Bolt Catcher Debris Analysis.

Catalyzing Innovation in Social Work Practice

ERIC Educational Resources Information Center

Traube, Dorian E.; Begun, Stephanie; Okpych, Nathanael; Choy-Brown, Mimi

2017-01-01

Social innovation is defined by novelty and improvement. This definition requires social work practice to be more effective or efficient than preexisting alternatives. Practice innovation is accomplished by leveraging technical, social, and economic factors to generate novel interventions, diffusion or adoption of the interventions into broader…

Time to tenure in Spanish universities: an event history analysis.

PubMed

Sanz-Menéndez, Luis; Cruz-Castro, Laura; Alva, Kenedy

2013-01-01

Understanding how institutional incentives and mechanisms for assigning recognition shape access to a permanent job is important. This study, based on data from questionnaire survey responses and publications of 1,257 university science, biomedical and engineering faculty in Spain, attempts to understand the timing of getting a permanent position and the relevant factors that account for this transition, in the context of dilemmas between mobility and permanence faced by organizations. Using event history analysis, the paper looks at the time to promotion and the effects of some relevant covariates associated to academic performance, social embeddedness and mobility. We find that research productivity contributes to career acceleration, but that other variables are also significantly associated to a faster transition. Factors associated to the social elements of academic life also play a role in reducing the time from PhD graduation to tenure. However, mobility significantly increases the duration of the non-tenure stage. In contrast with previous findings, the role of sex is minor. The variations in the length of time to promotion across different scientific domains is confirmed, with faster career advancement for those in the Engineering and Technological Sciences compared with academics in the Biological and Biomedical Sciences. Results show clear effects of seniority, and rewards to loyalty, in addition to some measurements of performance and quality of the university granting the PhD, as key elements speeding up career advancement. Findings suggest the existence of a system based on granting early permanent jobs to those that combine social embeddedness and team integration with some good credentials regarding past and potential future performance, rather than high levels of mobility.

Time to Tenure in Spanish Universities: An Event History Analysis

PubMed Central

Sanz-Menéndez, Luis; Cruz-Castro, Laura; Alva, Kenedy

2013-01-01

Understanding how institutional incentives and mechanisms for assigning recognition shape access to a permanent job is important. This study, based on data from questionnaire survey responses and publications of 1,257 university science, biomedical and engineering faculty in Spain, attempts to understand the timing of getting a permanent position and the relevant factors that account for this transition, in the context of dilemmas between mobility and permanence faced by organizations. Using event history analysis, the paper looks at the time to promotion and the effects of some relevant covariates associated to academic performance, social embeddedness and mobility. We find that research productivity contributes to career acceleration, but that other variables are also significantly associated to a faster transition. Factors associated to the social elements of academic life also play a role in reducing the time from PhD graduation to tenure. However, mobility significantly increases the duration of the non-tenure stage. In contrast with previous findings, the role of sex is minor. The variations in the length of time to promotion across different scientific domains is confirmed, with faster career advancement for those in the Engineering and Technological Sciences compared with academics in the Biological and Biomedical Sciences. Results show clear effects of seniority, and rewards to loyalty, in addition to some measurements of performance and quality of the university granting the PhD, as key elements speeding up career advancement. Findings suggest the existence of a system based on granting early permanent jobs to those that combine social embeddedness and team integration with some good credentials regarding past and potential future performance, rather than high levels of mobility. PMID:24116199

Fostering successful scientific software communities

NASA Astrophysics Data System (ADS)

Bangerth, W.; Heister, T.; Hwang, L.; Kellogg, L. H.

2016-12-01

Developing sustainable open source software packages for the sciences appears at first to be primarily a technical challenge: How can one create stable and robust algorithms, appropriate software designs, sufficient documentation, quality assurance strategies such as continuous integration and test suites, or backward compatibility approaches that yield high-quality software usable not only by the authors, but also the broader community of scientists? However, our experience from almost two decades of leading the development of the deal.II software library (http://www.dealii.org, a widely-used finite element package) and the ASPECT code (http://aspect.dealii.org, used to simulate convection in the Earth's mantle) has taught us that technical aspects are not the most difficult ones in scientific open source software. Rather, it is the social challenge of building and maintaining a community of users and developers interested in answering questions on user forums, contributing code, and jointly finding solutions to common technical and non-technical challenges. These problems are posed in an environment where project leaders typically have no resources to reward the majority of contributors, where very few people are specifically paid for the work they do on the project, and with frequent turnover of contributors as project members rotate into and out of jobs. In particular, much software work is done by graduate students who may become fluent enough in a software only a year or two before they leave academia. We will discuss strategies we have found do and do not work in maintaining and growing communities around the scientific software projects we lead. Specifically, we will discuss the management style necessary to keep contributors engaged, ways to give credit where credit is due, and structuring documentation to decrease reliance on forums and thereby allow user communities to grow without straining those who answer questions.

The DoD Gateway Information System: Bibliography, Directory of Resources, Prototype Experience, [and] User Interface Design.

ERIC Educational Resources Information Center

Cotter, Gladys A.; And Others

The Defense Technical Information Center (DTIC), an organization charged with providing information services to the Department of Defense (DoD) scientific and technical community, actively seeks ways to promote access to and utilization of scientific and technical information (STI) databases, online services, and networks relevant to the conduct…

Numerical simulation of deformation and failure processes of a complex technical object under impact loading

NASA Astrophysics Data System (ADS)

Kraus, E. I.; Shabalin, I. I.; Shabalin, T. I.

2018-04-01

The main points of development of numerical tools for simulation of deformation and failure of complex technical objects under nonstationary conditions of extreme loading are presented. The possibility of extending the dynamic method for construction of difference grids to the 3D case is shown. A 3D realization of discrete-continuum approach to the deformation and failure of complex technical objects is carried out. The efficiency of the existing software package for 3D modelling is shown.

Sulphursoil - Delano Development Corporation

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1985-06-01

A sizable amount of technical information has been accumulated on the effects of agricultural applications of the natural mineral product called Sul-Fe. This technical information supports the field observations of farmers, landscapers and gardeners who have used the product. Sul-Fe is often evaluated in terms of its sulphur content alone. When compared to elemental sulphur (100% sulphur), the 18 to 21% sulphur content of Sul-Fe seems relatively low. However, as the following technical data indicates, when judged on actual effects, Sul-Fe's complex mixture of minerals has several advantages over elemental sulphur. When judged on the basis of soil acidulation, Sul-Femore » has more immediate effects than elemental sulphur. The rapid acidifying effect is due to Sul-Fe's content of crystalline sulphuric acid. Sul-Fe also has long-term effects on soil pH due to its content of sulphur and sulfides and the time required to oxidize these materials. Elemental sulphur contains sulphur in only one chemical form which must be microbially oxidized before it becomes reactive in the soil solution, a reaction that takes quite some time in some soils. Sul-Fe is thus better than elemental sulphur in terms of immediate effects and comparable in terms of long term effects. Applied blends of Sul-Fe supplemented with elemental sulphur may provide for a maximization of both short and long term effects. An additional benefit derived from the use of Sul-Fe is the addition to the soil of a variety of trace nutrients including iron, calcium, zinc, copper, manganese, magnesium, and molybdenum.« less

47 CFR 95.631 - Emission types.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 5 2014-10-01 2014-10-01 false Emission types. 95.631 Section 95.631... SERVICES Technical Regulations Technical Standards § 95.631 Emission types. (a) A GMRS transmitter must transmit only emission types A1D, F1D, G1D, H1D, J1D, R1D, A3E, F3E, G3E, H3E, J3E or R3E. A non-voice...

47 CFR 95.631 - Emission types.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 5 2012-10-01 2012-10-01 false Emission types. 95.631 Section 95.631... SERVICES Technical Regulations Technical Standards § 95.631 Emission types. (a) A GMRS transmitter must transmit only emission types A1D, F1D, G1D, H1D, J1D, R1D, A3E, F3E, G3E, H3E, J3E or R3E. A non-voice...

Utility of Social Modeling for Proliferation Assessment - Preliminary Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coles, Garill A.; Gastelum, Zoe N.; Brothers, Alan J.

2009-06-01

This Preliminary Assessment draft report will present the results of a literature search and preliminary assessment of the body of research, analysis methods, models and data deemed to be relevant to the Utility of Social Modeling for Proliferation Assessment research. This report will provide: 1) a description of the problem space and the kinds of information pertinent to the problem space, 2) a discussion of key relevant or representative literature, 3) a discussion of models and modeling approaches judged to be potentially useful to the research, and 4) the next steps of this research that will be pursued based onmore » this preliminary assessment. This draft report represents a technical deliverable for the NA-22 Simulations, Algorithms, and Modeling (SAM) program. Specifically this draft report is the Task 1 deliverable for project PL09-UtilSocial-PD06, Utility of Social Modeling for Proliferation Assessment. This project investigates non-traditional use of social and cultural information to improve nuclear proliferation assessment, including nonproliferation assessment, proliferation resistance assessments, safeguards assessments and other related studies. These assessments often use and create technical information about the State’s posture towards proliferation, the vulnerability of a nuclear energy system to an undesired event, and the effectiveness of safeguards. This project will find and fuse social and technical information by explicitly considering the role of cultural, social and behavioral factors relevant to proliferation. The aim of this research is to describe and demonstrate if and how social science modeling has utility in proliferation assessment.« less

The Computer Science Technical Report (CS-TR) Project: A Pioneering Digital Library Project Viewed from a Library Perspective.

ERIC Educational Resources Information Center

Anderson, Greg; And Others

1996-01-01

Describes the Computer Science Technical Report Project, one of the earliest investigations into the system engineering of digital libraries which pioneered multiinstitutional collaborative research into technical, social, and legal issues related to the development and implementation of a large, heterogeneous, distributed digital library. (LRW)

78 FR 65242 - Occupational Exposure to Crystalline Silica; Extension of Comment Period; Extension of Period To...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

... scientific and technical analyses, OSHA requests that you disclose: (1) The nature of any financial... such as social security numbers and birthdates. If you submit scientific or technical studies or other... data and technical information submitted to the record. This request is consistent with Executive Order...

High Tech and the Upward Mobility of Non-Technical People.

ERIC Educational Resources Information Center

Kammire, Linda L.

The social and psychological effects of rapid technological advancement in the computer industry is the subject of this paper, which focuses on the concerns of people with non-technical backgrounds. It describes the career series, High Tech for Non-Technical People, created by the Georgia State University Career Development Center. The three…

The U.S. government technical report and the transfer of federally funded aerospace R & D

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1993-01-01

This article discusses the U.S. government technical report and the transfer of federally funded aerospace research and development in a conceptual framework of the federal government as a producer of scientific and technical information. The article summarizes current literature and research and discusses U.S. government technical report use and the importance of using data obtained from the NASA/DoD Aerospace Knowledge Diffusion Research Project. The authors make a case for changing existing U.S. technology policy and present a research agenda for the U.S. government technical report.

IT Labs Proof-of-Concept Project: Technical Data Interoperability (TDI) Pathfinder Via Emerging Standards

NASA Technical Reports Server (NTRS)

Conroy, Mike; Gill, Paul; Ingalls, John; Bengtsson, Kjell

2014-01-01

No known system is in place to allow NASA technical data interoperability throughout the whole life cycle. Life Cycle Cost (LCC) will be higher on many developing programs if action isn't taken soon to join disparate systems efficiently. Disparate technical data also increases safety risks from poorly integrated elements. NASA requires interoperability and industry standards, but breaking legacy ways is a challenge.

Abstracts of ARI Research Publications, FY 1979

DTIC Science & Technology

1980-11-01

Technical Report 483 ABSTRACTS OF ARI RESEARCH PUBLICATIONS FY 1979 -- C:) U. S . ArmyL.) LAa Research Institute for the Behavioral and Social...U. S . ARMY RESEARCH INSTITUTE FOR THE BEHAVIORAL AND SOCIAL SCIENCES A Field Operating Agency under the Jurisdiction of the Deputy Chief of Staff...PIEIT’S ATALOG NUMBER Technical Report 483 l L~,2 y. (-P- NUZE 4. TITLE (nd Subtfti.) S . TYPE OF REPORT & PERIOD COVERED ABSTRACTS OF ARI RESEARCH

Brokering Capabilities for EarthCube - supporting Multi-disciplinary Earth Science Research

NASA Astrophysics Data System (ADS)

Jodha Khalsa, Siri; Pearlman, Jay; Nativi, Stefano; Browdy, Steve; Parsons, Mark; Duerr, Ruth; Pearlman, Francoise

2013-04-01

The goal of NSF's EarthCube is to create a sustainable infrastructure that enables the sharing of all geosciences data, information, and knowledge in an open, transparent and inclusive manner. Brokering of data and improvements in discovery and access are a key to data exchange and promotion of collaboration across the geosciences. In this presentation we describe an evolutionary process of infrastructure and interoperability development focused on participation of existing science research infrastructures and augmenting them for improved access. All geosciences communities already have, to a greater or lesser degree, elements of an information infrastructure in place. These elements include resources such as data archives, catalogs, and portals as well as vocabularies, data models, protocols, best practices and other community conventions. What is necessary now is a process for levering these diverse infrastructure elements into an overall infrastructure that provides easy discovery, access and utilization of resources across disciplinary boundaries. Brokers connect disparate systems with only minimal burdens upon those systems, and enable the infrastructure to adjust to new technical developments and scientific requirements as they emerge. Robust cyberinfrastructure will arise only when social, organizational, and cultural issues are resolved in tandem with the creation of technology-based services. This is a governance issue, but is facilitated by infrastructure capabilities that can impact the uptake of new interdisciplinary collaborations and exchange. Thus brokering must address both the cyberinfrastructure and computer technology requirements and also the social issues to allow improved cross-domain collaborations. This is best done through use-case-driven requirements and agile, iterative development methods. It is important to start by solving real (not hypothetical) information access and use problems via small pilot projects that develop capabilities targeted to specific communities. Brokering, as a critical capability for connecting systems, evolves over time through more connections and increased functionality. This adaptive process allows for continual evaluation as to how well science-driven use cases are being met. There is a near term, and possibly unique, opportunity through EarthCube and European e-Infrastructure projects to increase the impact and interconnectivity of projects. In the developments described in this presentation, brokering has been demonstrated to be an essential part of a robust, adaptive technical infrastructure and demonstration and user scenarios can address of both the governance and detailed implementation paths forward. The EarthCube Brokering roadmap proposes the expansion of brokering pilots into fully operational prototypes that work with the broader science and informatics communities to answer these questions, connect existing and emerging systems, and evolve the EarthCube infrastructure.

Using Finite Element Method to Estimate the Material Properties of a Bearing Cage

DTIC Science & Technology

2018-02-01

UNCLASSIFIED UNCLASSIFIED AD-E403 988 Technical Report ARMET-TR-17035 USING FINITE ELEMENT METHOD TO ESTIMATE THE MATERIAL...TITLE AND SUBTITLE USING FINITE ELEMENT METHOD TO ESTIMATE THE MATERIAL PROPERTIES OF A BEARING CAGE 5a. CONTRACT NUMBER 5b. GRANT...specifications of non-metallic bearing cages are typically not supplied by the manufacturer. In order to setup a finite element analysis of a

Non-technical skills of surgical trainees and experienced surgeons.

PubMed

Gostlow, H; Marlow, N; Thomas, M J W; Hewett, P J; Kiermeier, A; Babidge, W; Altree, M; Pena, G; Maddern, G

2017-05-01

In addition to technical expertise, surgical competence requires effective non-technical skills to ensure patient safety and maintenance of standards. Recently the Royal Australasian College of Surgeons implemented a new Surgical Education and Training (SET) curriculum that incorporated non-technical skills considered essential for a competent surgeon. This study sought to compare the non-technical skills of experienced surgeons who completed their training before the introduction of SET with the non-technical skills of more recent trainees. Surgical trainees and experienced surgeons undertook a simulated scenario designed to challenge their non-technical skills. Scenarios were video recorded and participants were assessed using the Non-Technical Skills for Surgeons (NOTSS) scoring system. Participants were divided into subgroups according to years of experience and their NOTSS scores were compared. For most NOTSS elements, mean scores increased initially, peaking around the time of Fellowship, before decreasing roughly linearly over time. There was a significant downward trend in score with increasing years since being awarded Fellowship for six of the 12 NOTSS elements: considering options (score -0·015 units per year), implementing and reviewing decisions (-0·020 per year), establishing a shared understanding (-0·014 per year), setting and maintaining standards (-0·024 per year), supporting others (-0·031 per year) and coping with pressure (-0·015 per year). The drop in NOTSS score was unexpected and highlights that even experienced surgeons are not immune to deficiencies in non-technical skills. Consideration should be given to continuing professional development programmes focusing on non-technical skills, regardless of the level of professional experience. © 2017 BJS Society Ltd Published by John Wiley & Sons Ltd.

Health as Submission and Social Responsibilities: Embodied Experiences of Javanese Women With Type II Diabetes.

PubMed

Pitaloka, Dyah; Hsieh, Elaine

2015-08-01

By examining women's experiences with type II diabetes, we explore how illness can provide resources to construct meanings of everyday life in Javanese culture. We conducted in-depth interviews with 30 female participants in Central Java, Indonesia, and adopted grounded theory for data analysis. We identified four themes that diabetes serves as resources for women in Indonesia to (a) normalize suffering, (b) resist social control, (c) accept fate, and (d) validate faith. We concluded by noting three unique aspects of Javanese women's illness management. First, through the performance of submission, our participants demonstrated spirituality and religiosity as essential elements of health. Second, diabetes empowers individuals in everyday suffering through two divergent processes: embracing submission and resisting control. Finally, diabetes provides opportunities for individuals within a social network to (re)negotiate social responsibilities. In summary, diabetes provides unique resources to empower our participants to obtain voices that they otherwise would not have had. © The Author(s) 2015.

The NASA role in major areas of human concern: Transportation

NASA Technical Reports Server (NTRS)

1973-01-01

After introducing some of the general factors that have affected progress in the transportation area, NASA program elements are examined to illustrate relevant points of contact. Interpretive steps are taken throughout the statement to show a few of the more important ways people's lives have been affected as a result of the work of NASA and other organizations functioning in this area. The principal documents used and interviews conducted are identified after the conclusion of this statement. This statement, it should be noted, is incomplete in many respects, primarily because it reflects only a small number of the technical, economic, and social forces affecting American life. Taken as a summary statement, however, it hopefully will provide a useful basis for better understanding NASA's role in the national attempt to upgrade the quality of transportation services.

High Technology Engineering Services, Inc. fiscal year 1993 and 1994 research and development report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This document has been prepared by the Professional Staff of High Technology Engineering Services, Inc. (HTES) for fiscal year (FY) 1993. Work was performed for various aspects of mechanical design and analysis, materials development and properties quantification, nuclear environment performance, and engineering program prioritization. The tasks enumerated in the subcontract, attachment B are: 1. Assist in preparation of final R&D report for SDC detector development. 2. Subcontractor shall make contributions to the development of innovative processes for the manufacture of quasi- isotropic, enhanced thermal conductivity compression molded advanced composite materials. 3. Perform finite element analysis as it relates to themore » Superconducting Super Collider Silicon Tracking System, both mechanical and thermal, of very thin section advanced composite materials. 4. Subcontractor shall perform technical studies, reviews, and assessments of the current program for advanced composites materials processing and testing. 5. Subcontractor shall attend meetings and discussions as directed by MEE-12 technical representative. Unfortunately during the course of FY93, technical and financial challenges prevailed against the aggressive goals set for the program. In point of fact, less than 25% of the contract value was able to be expended due to technical delays and programmatic funding cuts. Also, contracting difficulties with the SSC Lab and financial burdens at Los Alamos totally stopped progress on the subject subcontract during the whole of FY94. This was a great blow to me and the HTES, Inc. technical staff. Despite the negative influences over the years, significant progress was made in materials properties quantification and development of essential research and development documentation. The following brief report and attendant appendices will address these achievements.« less

After Action Review Tools for Dismounted Soldier Systems

DTIC Science & Technology

2008-06-01

Social Sciences A Directorate of the Department of the Army Deputy Chief of Staff, G1 Authorized and approved for distribution: BARBARA A. BLACK, Ph.D...began to improve both the quantity and quality of food supplies. However, the greatest change came in April with the arrival of Friedrich Wilhelm von...Management during training. 41 DATE: TA *IMMM27 lwba:4 MR TES Casftsa MwaWr SYSTM STATUS: RUNNING Training Elements in View 3 Pre Opicwlg p Post OPS C u S Q

Conception preliminaire de disques de turbine axiale pour moteurs d'aeronefs

NASA Astrophysics Data System (ADS)

Ouellet, Yannick

The preliminary design phase of a turbine rotor has an important impact on the architecture of a new engine definition, as it sets the technical orientation right from start and provides a good estimate of product performance, weight and cost. In addition, the execution speed at this preliminary phase has become critical into capturing business opportunities. Improving upfront accuracy also alleviates downstream detailed design work and therefore reduces overall product development cycle time. This preliminary phase contains elements slowing down its process, including low interoperability of currently used systems, incompatibility of software and ineffective management of data. In order to overcome these barriers, we have developed the first module of a new Design and Analysis (D&A) platform for the rotor disc. This complete platform ensures integration of different tools processing in batch mode, and is driven from a single graphical user interface. The platform developed has been linked with different optimization methods (algorithms, configuration) in order to automate the disc design and propose best practices for rotor structural optimization. This methodology allowed reduction in design cycle time and improvement of performance. It was applied on two reference P&WC axial discs. The platform's architecture was also used in the development of reference charts to better understand disc performance within given design space. Four high pressure rotor discs of P&WC turbofan and turboprop engines were used to generate the technical charts and understand the effect of various parameters. The new tools supporting disc D&A, combined with the optimization process and reference charts, has proven to be profitable in terms of component performance and engineering effort inputs.

High-strength cellular ceramic composites with 3D microarchitecture.

PubMed

Bauer, Jens; Hengsbach, Stefan; Tesari, Iwiza; Schwaiger, Ruth; Kraft, Oliver

2014-02-18

To enhance the strength-to-weight ratio of a material, one may try to either improve the strength or lower the density, or both. The lightest solid materials have a density in the range of 1,000 kg/m(3); only cellular materials, such as technical foams, can reach considerably lower values. However, compared with corresponding bulk materials, their specific strength generally is significantly lower. Cellular topologies may be divided into bending- and stretching-dominated ones. Technical foams are structured randomly and behave in a bending-dominated way, which is less weight efficient, with respect to strength, than stretching-dominated behavior, such as in regular braced frameworks. Cancellous bone and other natural cellular solids have an optimized architecture. Their basic material is structured hierarchically and consists of nanometer-size elements, providing a benefit from size effects in the material strength. Designing cellular materials with a specific microarchitecture would allow one to exploit the structural advantages of stretching-dominated constructions as well as size-dependent strengthening effects. In this paper, we demonstrate that such materials may be fabricated. Applying 3D laser lithography, we produced and characterized micro-truss and -shell structures made from alumina-polymer composite. Size-dependent strengthening of alumina shells has been observed, particularly when applied with a characteristic thickness below 100 nm. The presented artificial cellular materials reach compressive strengths up to 280 MPa with densities well below 1,000 kg/m(3).

Reinvigorating the concept of situation in social psychology.

PubMed

Reis, Harry T

2008-11-01

The concept of situation has a long and venerable history in social psychology. The author argues that recent approaches to the concept of situation have confused certain important elements. Herein, the author proposes that attention to three of these elements will reinvigorate the concept of situation in social psychology: (a) that the analysis of situations should begin with their objective features; (b) that situations should be conceptualized as affordances; and (c) that the interpersonal core of situations, in particular the extent to which they are influenced by relationships, is the proper and most profitable focus for social psychology. These elements are consistent with recent developments in the study of situated social cognition and may help better define social psychology's position within the sciences.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 34: Users and uses of DOD technical reports: A report from the field

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1993-01-01

The NASA/DoD Aerospace Knowledge Diffusion Research Project attempts to understand the information environment in which U.S. aerospace engineers and scientists work, the information-seeking behavior of U.S. aerospace engineers and scientists, and the factors that influence the use of scientific and technical information (STI) (Pinelli, Barclay, and Kennedy, 1991). Such an understanding could (1) lead to the development of practical theory, (2) contribute to the design and development of aerospace information systems, and (3) have practical implications for transferring the results of federally funded aerospace research and development (R&D) to the U.S. aerospace community. This paper presents data from two information-seeking behavior studies involving U.S. aerospace engineers and scientists that were undertaken as Phase 1 activities of the NASA/DoD Aerospace Knowledge Diffusion Research Project. Responses from three groups of respondents - DoD, other government, and industry - are presented for two sets of selected questions. One set focuses on DoD technical reports: their use and importance, reasons for non-use, the factors affecting their use, the sources used to find out about them and the sources used to physically obtain them, and the quality of DoD technical reports. The second set focuses on information sources used in problem solving: the use of U.S. government technical reports in problem solving and the information sources used to find out about U.S. government technical reports.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 33: The technical communications practices of US aerospace engineers and scientists: Results of the phase 1 AIAA mail survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1995-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of U.S. aerospace engineers and scientists who are members of the American Institute of Aeronautics and Astronautics (AIAA).

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 24: The technical communications practices of US aerospace engineers and scientists: Results of the phase 1 SAE mail survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of U.S. aerospace engineers and scientists affiliated with the Society of Automotive Engineers (SAE).

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 25: The technical communications practices of British aerospace engineers and scientists: Results of the phase 4 RAeS mail survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of British aerospace engineers and scientists.

Roadmap to Perkins III: The Carl D. Perkins Vocational and Technical Education Act of 1998. A Guidebook for Illinois.

ERIC Educational Resources Information Center

Hess-Grabill, Donella; Bueno, Soyon

This guidebook is intended as a road map to the Carl D. Perkins Vocational Technical Education Act of 1998 (Perkins III) for career-technical education (CTE) practitioners and policymakers in Illinois. The following topics are among those covered: (1) framework for Perkins III (national educational reform, Illinois provisions for quality CTE,…

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 45; The Technical Communications Practices of US Aerospace Engineers and Scientists: Results of the Phase 3 US Aerospace Engineering Educators Survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1996-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. Little is also known about the intermediary-based system that is used to transfer the results of federally funded R&D to the U.S. aerospace industry. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports, present a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communication practices of U.S. aerospace engineers and scientists who were members of the American Institute of Aeronautics and Astronautics (AIAA) and identified themselves as educators.

Restoring Fort Frontenac in 3D: Effective Usage of 3D Technology for Heritage Visualization

NASA Astrophysics Data System (ADS)

Yabe, M.; Goins, E.; Jackson, C.; Halbstein, D.; Foster, S.; Bazely, S.

2015-02-01

This paper is composed of three elements: 3D modeling, web design, and heritage visualization. The aim is to use computer graphics design to inform and create an interest in historical visualization by rebuilding Fort Frontenac using 3D modeling and interactive design. The final model will be integr ated into an interactive website to learn more about the fort's historic imp ortance. It is apparent that using computer graphics can save time and money when it comes to historical visualization. Visitors do not have to travel to the actual archaeological buildings. They can simply use the Web in their own home to learn about this information virtually. Meticulously following historical records to create a sophisticated restoration of archaeological buildings will draw viewers into visualizations, such as the historical world of Fort Frontenac. As a result, it allows the viewers to effectively understand the fort's social sy stem, habits, and historical events.

A Social Network Analysis of the National Materials Competency at Naval Air Systems Command

DTIC Science & Technology

2002-09-01

language held by individuals within the structure. (Lesser, 2000, p. 4) Bourdieu defines social capital as decomposable into two elements: first, the...The fundamental proposition of social capital theory is that the network ties provide access to resources and that social relations constitute...transferring knowledge are being identified as a central element of organizational advantage. Social capital theory provides a sounds basis for explaining

Inventory of available data elements for the San Bernardino, California region

NASA Technical Reports Server (NTRS)

Christenson, J.; Michel, R.

1981-01-01

Elements of data sets that are available to be integrated for the San Bernardino vertical data integration project are given. Each of the data sets has specified for it the ownership, validity, accuracy and technical requirements for integration.

The element of naturalness when evaluating image quality of digital photo documentation after sexual assault.

PubMed

Ernst, E J; Speck, P M; Fitzpatrick, J J

2012-01-01

Digital photography is a valuable adjunct to document physical injuries after sexual assault. In order for a digital photograph to have high image quality, there must exist a high level of naturalness. Digital photo documentation has varying degrees of naturalness; however, for a photograph to be natural, specific technical elements for the viewer must be satisfied. No tool was available to rate the naturalness of digital photo documentation of female genital injuries after sexual assault. The Photo Documentation Image Quality Scoring System (PDIQSS) tool was developed to rate technical elements for naturalness. Using this tool, experts evaluated randomly selected digital photographs of female genital injuries captured following sexual assault. Naturalness of female genital injuries following sexual assault was demonstrated when measured in all dimensions.

Experiments in interdisciplinarity: Responsible research and innovation and the public good

PubMed Central

Åm, Heidrun

2018-01-01

In Europe, responsible research and innovation (RRI) has emerged as a science policy measure that demands the early integration of a broad range of social actors and perspectives into research and development (R&D). More collaboration of the social sciences and humanities (SSH) with science and engineering appears within this policy framework as a crucial element that will enable better technological development. However, RRI is new to both natural scientists and SSH scholars, and interdisciplinary collaborations are challenging for many reasons. In this paper, we discuss these challenges while suggesting that what RRI can be in a particular project is not a given but remains an empirical question. Natural scientists and SSH scholars need to coresearch RRI in an experimental mode. PMID:29579043

Experiments in interdisciplinarity: Responsible research and innovation and the public good.

PubMed

Delgado, Ana; Åm, Heidrun

2018-03-01

In Europe, responsible research and innovation (RRI) has emerged as a science policy measure that demands the early integration of a broad range of social actors and perspectives into research and development (R&D). More collaboration of the social sciences and humanities (SSH) with science and engineering appears within this policy framework as a crucial element that will enable better technological development. However, RRI is new to both natural scientists and SSH scholars, and interdisciplinary collaborations are challenging for many reasons. In this paper, we discuss these challenges while suggesting that what RRI can be in a particular project is not a given but remains an empirical question. Natural scientists and SSH scholars need to coresearch RRI in an experimental mode.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 31: The technical communications practices of US aerospace engineers and scientists: Results of the phase 1 SME mail survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical communications practices of U.S. aerospace engineers and scientists affiliated with, not necessarily belonging to, the Society of Manufacturing Engineers (SME).

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 13: Source selection and information use by US aerospace engineers and scientists: Results of a telephone survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Glassman, Nanci A.

1992-01-01

A telephone survey of U.S. aerospace engineers and scientists belonging to the Society of Automotive Engineers (SAE) was conducted between December 4, 1991 and January 5, 1992. The survey was undertaken to (1) validate the telephone survey as an appropriate technique for collecting data from U.S. aerospace engineers and scientists; (2) collect information about how the results of NASA/DoD aerospace research are used in the R&D process; (3) identify those selection criteria which affect the use of federally-funded aerospace R&D; and (4) obtain information that could be used to develop a self-administered mail questionnaire for use with the same population. The average rating of importance of U.S. government technical reports was 2.5 (on a 4-point scale); The mean/median number of times U.S. government technical reports were used per 6 months was 8/2. Factors scoring highest for U.S. government technical reports were technical accuracy (2.9), reliable data and technical information (2.8), and contains comprehensive data and information (2.7) on a 4-point system. The factors scoring highest for influencing the use of U.S. government technical reports were relevance (3.1), technical accuracy (3.06), and reliable data/information (3.02). Ease of use, familiarity, technical accuracy, and relevance correlated with use of U.S. government technical reports. Survey demographics, survey questionnaire, and the NASA/DoD Aerospace Knowledge Diffusion Research Project publications list are included.

A business man views commercial ventures in space.

NASA Technical Reports Server (NTRS)

Scarff, D. D.; Bloom, H. L.

1973-01-01

Paper reviews technical, resource planning and marketing steps an industrial organization must perform in arriving at a decision to undertake space development and production of commercial products or services for Users on the ground. Technical elements are supported by particular examples. Analysis of required resources emphasizes facility and financial inter-relationships between commercial organizations and NASA. Marketing planning covers elements of profitability. Paper addresses questions related to protection of corporate stockholders and public interest, investment decision timing, budget variations. Paper concludes with observations on timeliness of planning shuttle-based commercial ventures and on key industry/NASA problems and decisions.

7 CFR 652.5 - Participant acquisition of technical services.

Code of Federal Regulations, 2010 CFR

2010-01-01

... technical service providers. (d) The Department may approve written agreements for technical assistance... identify in the particular program contract or written agreement the payment provisions for technical... 7 Agriculture 6 2010-01-01 2010-01-01 false Participant acquisition of technical services. 652.5...

Development of a cultural heritage object BIM model

NASA Astrophysics Data System (ADS)

Braila, Natalya; Vakhrusheva, Svetlana; Martynenko, Elena; Kisel, Tatyana

2017-10-01

The BIM technology during her creation has been aimed, first of all, at design and construction branch, but its application in the field of studying and operation of architectural heritage can essentially change and transfer this kind of activity to new qualitative level. The question of effective introduction of BIM technologies at the solution of administrative questions of operation and development of monuments of architecture is considered in article. Creation of the information model of the building object of cultural heritage including a full complex of information on an object is offered: historical and archival, legal, technical, administrative, etc. The 3D model of an object of cultural heritage with color marking of elements on degree of wear and a first priority of carrying out repair will become one of components of model. This model will allow to estimate visually technical condition of the building in general and to gain general idea about scales of necessary repair and construction actions that promotes improvement of quality of operation of an object, and also simplifies and accelerates processing of information and in need of a memorial building assessment as subject to investment.

76 FR 31416 - Federal Acquisition Regulation; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-31

... ADMINISTRATION 48 CFR Parts 52 and 53 [FAC 2005-52; Item VI; Docket 2011-0078; Sequence 2] Federal Acquisition... publication schedules. Please cite FAC 2005-52, Technical Amendments. SUPPLEMENTARY INFORMATION: In order to update certain elements in 48 CFR parts 52 and 53, this document makes editorial changes to the Federal...

Technical Support Services for the Office of Naval Research Littoral Warfare Advanced Development Project

DTIC Science & Technology

2005-09-30

Technical Support Services for the Office of Naval Research Littoral Warfare Advanced Development Project William R. Metzger Marine...Support Services for the Office of Naval Research Littoral Warfare Advanced Development Project 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT

Scientific and Technical Chinese, Volume II. Glossary.

ERIC Educational Resources Information Center

Kao, Kung-yi; And Others

A composite English-to-Chinese glossary of all terms introduced in the individual lessons of "Scientific and Technical Chinese" is presented here. The appendices include lists of weights and measures and chemical elements, and a partial list of Chinese government organizations and research institutes related to science and technology.…

Evaluating Social Causality and Responsibility Models: An Initial Report

DTIC Science & Technology

2005-01-01

ICT Technical Report ICT-TR-03-2005 Evaluating Social Causality and Responsibility ... social intelligent agents. In this report, we present a general computational model of social causality and responsibility , and empirical results of...2005 to 00-00-2005 4. TITLE AND SUBTITLE Evaluating Social Causality and Responsibility Models: An Initial Report 5a. CONTRACT NUMBER 5b. GRANT

32 CFR Appendix D to Part 286 - DD Form 2086-1, “Record of Freedom of Information (FOI) Processing Cost for Technical Data”

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false DD Form 2086-1, âRecord of Freedom of Information (FOI) Processing Cost for Technical Dataâ D Appendix D to Part 286 National Defense Department of... FREEDOM OF INFORMATION ACT PROGRAM REGULATION Pt. 286, App. D Appendix D to Part 286—DD Form 2086-1...

Department of Defense Access to Intellectual Property for Weapon Systems Sustainment

DTIC Science & Technology

2017-05-01

and acquiring technical data rights …  The cost benefit analysis of including a priced contract option for the future delivery of technical data...entail in terms of cost and benefits , while one of the activities to be finalized is the contract-specific technical data elements.66...Virginia 22311-1882 May 2017 Approved for public release; distribution is unlimited. IDA Paper P-8266 Log: H 17-000030 About This Publication This

Scope and Challenges of Technical Education: A Kerala Perspective

ERIC Educational Resources Information Center

Rahman, M. Abdul; Unnikrishnan, Ramesh

2015-01-01

Technical education contributes a major share to the overall education system and plays a vital role in the social and economic development of our nation. Since independence, the technical education system in our country has grown into a fairly large-sized system, offering opportunities for education and training in a wide variety of trades and…

High-performance commercial building systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selkowitz, Stephen

2003-10-01

This report summarizes key technical accomplishments resulting from the three year PIER-funded R&D program, ''High Performance Commercial Building Systems'' (HPCBS). The program targets the commercial building sector in California, an end-use sector that accounts for about one-third of all California electricity consumption and an even larger fraction of peak demand, at a cost of over $10B/year. Commercial buildings also have a major impact on occupant health, comfort and productivity. Building design and operations practices that influence energy use are deeply engrained in a fragmented, risk-averse industry that is slow to change. Although California's aggressive standards efforts have resulted in newmore » buildings designed to use less energy than those constructed 20 years ago, the actual savings realized are still well below technical and economic potentials. The broad goal of this program is to develop and deploy a set of energy-saving technologies, strategies, and techniques, and improve processes for designing, commissioning, and operating commercial buildings, while improving health, comfort, and performance of occupants, all in a manner consistent with sound economic investment practices. Results are to be broadly applicable to the commercial sector for different building sizes and types, e.g. offices and schools, for different classes of ownership, both public and private, and for owner-occupied as well as speculative buildings. The program aims to facilitate significant electricity use savings in the California commercial sector by 2015, while assuring that these savings are affordable and promote high quality indoor environments. The five linked technical program elements contain 14 projects with 41 distinct R&D tasks. Collectively they form a comprehensive Research, Development, and Demonstration (RD&D) program with the potential to capture large savings in the commercial building sector, providing significant economic benefits to building owners and health and performance benefits to occupants. At the same time this program can strengthen the growing energy efficiency industry in California by providing new jobs and growth opportunities for companies providing the technology, systems, software, design, and building services to the commercial sector. The broad objectives across all five program elements were: (1) To develop and deploy an integrated set of tools and techniques to support the design and operation of energy-efficient commercial buildings; (2) To develop open software specifications for a building data model that will support the interoperability of these tools throughout the building life-cycle; (3) To create new technology options (hardware and controls) for substantially reducing controllable lighting, envelope, and cooling loads in buildings; (4) To create and implement a new generation of diagnostic techniques so that commissioning and efficient building operations can be accomplished reliably and cost effectively and provide sustained energy savings; (5) To enhance the health, comfort and performance of building occupants. (6) To provide the information technology infrastructure for owners to minimize their energy costs and manage their energy information in a manner that creates added value for their buildings as the commercial sector transitions to an era of deregulated utility markets, distributed generation, and changing business practices. Our ultimate goal is for our R&D effort to have measurable market impact. This requires that the research tasks be carried out with a variety of connections to key market actors or trends so that they are recognized as relevant and useful and can be adopted by expected users. While some of this activity is directly integrated into our research tasks, the handoff from ''market-connected R&D'' to ''field deployment'' is still an art as well as a science and in many areas requires resources and a timeframe well beyond the scope of this PIER research program. The TAGs, PAC and other industry partners have assisted directly in this effort by reviewing and critiquing work to date, and by partnering in activities that advance results toward market impacts. The goals, objectives and key accomplishments of each technical program element and projects are described in the sections that follow. For each project we then summarize the Task Approach, the Outcomes of each task, and our Conclusions and Recommendations. We also provide a list and short summary of each significant research product e.g. report, prototype, software, standard, etc.« less

NREL Energy Storage Projects. FY2014 Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pesaran, Ahmad; Ban, Chunmei; Burton, Evan

2015-03-01

The National Renewable Energy Laboratory supports energy storage R&D under the Office of Vehicle Technologies at the U.S. Department of Energy. The DOE Energy Storage Program’s charter is to develop battery technologies that will enable large market penetration of electric drive vehicles. These vehicles could have a significant impact on the nation’s goal of reducing dependence on imported oil and gaseous pollutant emissions. DOE has established several program activities to address and overcome the barriers limiting the penetration of electric drive battery technologies: cost, performance, safety, and life. These programs are; Advanced Battery Development through the United States Advanced Batterymore » Consortium (USABC); Battery Testing, Analysis, and Design; Applied Battery Research (ABR); and Focused Fundamental Research, or Batteries for Advanced Transportation Technologies (BATT) In FY14, DOE funded NREL to make technical contributions to all of these R&D activities. This report summarizes NREL’s R&D projects in FY14 in support of the USABC; Battery Testing, Analysis, and Design; ABR; and BATT program elements. The FY14 projects under NREL’s Energy Storage R&D program are briefly described below. Each of these is discussed in depth in this report.« less

Technical Topic 3.2.2.d Bayesian and Non-Parametric Statistics: Integration of Neural Networks with Bayesian Networks for Data Fusion and Predictive Modeling

DTIC Science & Technology

2016-05-31

and included explosives such as TATP, HMTD, RDX, RDX, ammonium nitrate , potassium perchlorate, potassium nitrate , sugar, and TNT. The approach...Distribution Unlimited UU UU UU UU 31-05-2016 15-Apr-2014 14-Jan-2015 Final Report: Technical Topic 3.2.2. d Bayesian and Non- parametric Statistics...of Papers published in non peer-reviewed journals: Final Report: Technical Topic 3.2.2. d Bayesian and Non-parametric Statistics: Integration of Neural

The Differentiation of Social Demands in Europe. The Social Basis of the European Models of Capitalism

ERIC Educational Resources Information Center

Amable, Bruno

2009-01-01

This paper tests the impact of various determinants of the preference for two key elements of the European social models: redistribution and trade unions, using individual data from the first round of the European Social Survey. The basic hypothesis is that the main determinant of an individual's support for these elements of the European models…

Finite Element Barotropic Model for the Indian and Western Pacific OceanBasin: Tidal Model Data Comparisons and Sensitivities

DTIC Science & Technology

2018-01-11

From - To) 01/11/2018 Final Technical Report June 01 2016 - Dec 30 2017 4. TITLE AND SUBTITLE Sa. CONTRACT NUMBER Finite - Element Barotropic Model...grid finite - element barotropic fully hydrodynamic model in order to understand the shallow-water dynamics of the Indian Ocean and Western Pacific Ocean...dissipative dissipative processes are explored. 15. SUBJECTTERMS finite - element , unstructured grid, barotropic tides, bathymetry, internal tide

Data Element Dictionary: Finance. A Technical Report Concerning Finance Related Data Elements in the WICHE Management Information Systems Program. First Edition.

ERIC Educational Resources Information Center

Thomas, Charles R.

This document is one of the 5 sections of the Data Element Dictionary developed as part of the WICHE Management Information Systems (MIS) Program. The elements in this section apply to both the current and historical data concerning finance. The purpose of the WICHE MIS Program is to make it possible to derive data which will be truly comparable…

Usage of Video Analysis of Traffic Conflicts for the Evaluation of Inappropriately Designed Building Elements on Intersections

NASA Astrophysics Data System (ADS)

Krivda, Vladislav; Petru, Jan

2018-04-01

Human society is constantly evolving in all areas. The transport is no exception – especially development of road transport is considerable and visible on all levels. However, it is necessary to look for tools that can harmonize economic and social progress with the full preservation of the environment for future generations. The so-called sustainable development of road transport is also closely related to the issue of creating safe transport infrastructure. For example, roads must be in compliance with technical rules on one hand and on the other one they have to be clearly understandable for all road participants (drivers, pedestrians, etc.). Unfortunately, even if the designer of transport construction meets the technical requirements, the result is a dangerous place where very frequently the accidents or traffic conflicts take place. There exist statistics of accidents, but on the contrary, there are not any statistics of traffic conflicts. And simply monitoring the traffic conflicts can lead to early detection of problematic places in road infrastructure and thus increasing the safety in the road traffic. There are many methods used for monitoring traffic conflicts. The method used in the Czech Republic is described in the submitted paper. The original method, which monitored mainly and only the behaviour of drivers and their mistakes, was innovated, so that it could be used also for evaluation of inappropriately designed building elements of road constructions. Therefore, the paper deals with the description of so-called Innovated Video Analysis of Traffic Conflicts (IVATC) and with the usage of this method for one particular example of intersection, where larger vehicles (buses, trucks, etc.) had problems with passing through it. It points out to the fact that even a relatively small change can lead to the increase of the road safety.

CAT-ASVAB Technical Bulletin Number 1

DTIC Science & Technology

2006-03-01

CAT -ASVAB Technical Bulletin #1 Personnel Testing Division Defense Manpower Data Center March 2006 Report...2. REPORT TYPE N/A 3. DATES COVERED - 4. TITLE AND SUBTITLE CAT -ASVAB Technical Bulletin #1 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c...Hetter, R. D. "Psychometric Procedures for Administering CAT -ASVAB" (pp. 131-140) Chapter 4 Hetter, R. D., & Sympson J. B. "Item Exposure

A finite element: Boundary integral method for electromagnetic scattering. Ph.D. Thesis Technical Report, Feb. - Sep. 1992

NASA Technical Reports Server (NTRS)

Collins, J. D.; Volakis, John L.

1992-01-01

A method that combines the finite element and boundary integral techniques for the numerical solution of electromagnetic scattering problems is presented. The finite element method is well known for requiring a low order storage and for its capability to model inhomogeneous structures. Of particular emphasis in this work is the reduction of the storage requirement by terminating the finite element mesh on a boundary in a fashion which renders the boundary integrals in convolutional form. The fast Fourier transform is then used to evaluate these integrals in a conjugate gradient solver, without a need to generate the actual matrix. This method has a marked advantage over traditional integral equation approaches with respect to the storage requirement of highly inhomogeneous structures. Rectangular, circular, and ogival mesh termination boundaries are examined for two-dimensional scattering. In the case of axially symmetric structures, the boundary integral matrix storage is reduced by exploiting matrix symmetries and solving the resulting system via the conjugate gradient method. In each case several results are presented for various scatterers aimed at validating the method and providing an assessment of its capabilities. Important in methods incorporating boundary integral equations is the issue of internal resonance. A method is implemented for their removal, and is shown to be effective in the two-dimensional and three-dimensional applications.

Customisation of an instrument to assess anaesthesiologists' non-technical skills.

PubMed

Jepsen, Rikke M H G; Spanager, Lene; Lyk-Jensen, Helle T; Dieckmann, Peter; Østergaard, Doris

2015-02-22

The objectives of the study were to identify Danish anaesthesiologists' non-technical skills and to customise the Scottish-developed Anaesthetists' Non-Technical Skills instrument for Danish anaesthesiologists. Six semi-structured group interviews were conducted with 31 operating room team members: anaes-thesiologists, nurse anaesthetists, surgeons, and scrub nurses. Interviews were transcribed verbatim and analysed using directed content analysis. Anaesthesiologists' non-technical skills were identified, coded, and sorted using the original instrument as a basis. The resulting prototype instrument was discussed with anaesthesiologists from 17 centres to ensure face validity. Interviews lasted 46-67 minutes. Identified examples of anaesthesiologists' good or poor non-technical skills fit the four categories in the original instrument: situation awareness; decision making; team working; and task management. Anaesthesiologists' leadership role in the operating room was emphasised: the original 'Task Management' category was named 'Leadership'. One new element, 'Demonstrating self-awareness' was added under the category 'Situation Awareness'. Compared with the original instrument, half of the behavioural markers were new, which reflected that being aware of and communicating one's own abilities to the team; working systematically; and speaking up to avoid adverse events were important skills. The Anaesthetists' Non-Technical Skills instrument was customised to a Danish setting using the identified non-technical skills for anaesthesiologists and the original instrument as basis. The customised instrument comprises four categories and 16 underpinning elements supported by multiple behavioural markers. Identifying non-technical skills through semi-structured group interviews and analysing them using direct content analysis proved a useful method for customising an assessment instrument to another setting.

Geometrically nonlinear analysis of layered composite plates and shells

NASA Technical Reports Server (NTRS)

Chao, W. C.; Reddy, J. N.

1983-01-01

A degenerated three dimensional finite element, based on the incremental total Lagrangian formulation of a three dimensional layered anisotropic medium was developed. Its use in the geometrically nonlinear, static and dynamic, analysis of layered composite plates and shells is demonstrated. A two dimenisonal finite element based on the Sanders shell theory with the von Karman (nonlinear) strains was developed. It is shown that the deflections obtained by the 2D shell element deviate from those obtained by the more accurate 3D element for deep shells. The 3D degenerated element can be used to model general shells that are not necessarily doubly curved. The 3D degenerated element is computationally more demanding than the 2D shell theory element for a given problem. It is found that the 3D element is an efficient element for the analysis of layered composite plates and shells undergoing large displacements and transient motion.

Sustainable Biofuels A Transitions Approach to Understanding the Global Expansion of Ethanol and Biodiesel

NASA Astrophysics Data System (ADS)

Cottes, Jeffrey Jacob

Between 1998 and 2008, the promise of biofuels to increase rural development, enhance energy security, and reduce greenhouse gas emissions stimulated their diffusion across international markets. This rapid expansion of ethanol and biodiesel encouraged many jurisdictions to implement biofuels expansion policies and programs. Global biofuels, characterised by mass production and international trade of ethanol and biodiesel, occurred despite their long history as marginal technologies on the fringe of the petroleum-based transportation energy regime. The first purpose of this dissertation is to examine the global expansion of ethanol and biodiesel to understand how these recurrent socio-technological failures co-evolved with petroleum transportation fuels. Drawing from the field of socio-technical transitions, this dissertation also assesses the global expansion of ethanol and biodiesel to determine whether or not these first generation biofuels are sustainable. Numerous studies have assessed the technical effects of ethanol and biodiesel, but effects-based technical assessments of transport biofuels are unable to explain the interaction of wider system elements. The configuration of multi-level factors (i.e., niche development, the technological regime, and the socio-technical landscape) informs the present and emerging social functions of biofuels, which become relevant when determining how biofuels might become a sustainable energy option. The biofuels regimes that evolved in Brazil, the United States, and the European Union provide case studies show how ethanol and biodiesel expanded from fringe fuels to global commodities. The production infrastructures within these dominant biofuels regimes contribute to a persistence of unsustainable first generation biofuels that can inhibit the technical development and sustainability of biofuels. However, new and emerging ethanol and biodiesel markets are relatively small in comparison to the dominant regimes, and can readily adapt to technical and regulatory change. This dissertation argues that dominant biofuels regimes have not produced a sustainable energy option. It explores the Canadian case to evaluate the opportunities for niche development, and suggests that small markets can develop niche innovations by regulating the insertion of sustainability criteria in order to de-align the dominant trajectory of global biofuels production regimes and encourage their re-alignment in a more sustainable configuration.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report number 20: The use of selected information products and services by US aerospace engineers and scientists: Results of two surveys

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally, funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DoD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from two surveys of our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report and close with a brief overview of on-going research into aerospace knowledge diffusion focusing on the role of the industry-affiliated information intermediary.

TECHNICAL REPORTS DATABASE

EPA Science Inventory

The Defense Technical Information Center (DTIC?) is the central facility for the collection and dissemination of scientific and technical information for the Department of Defense (DoD). Much of this information is made available by DTIC in the form of technical reports about com...

7 CFR 1775.36 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (CONTINUED) TECHNICAL ASSISTANCE GRANTS Technical Assistance and Training Grants § 1775.36 Purpose. Grants... water and/or waste disposal loan/grant applications. (d) Provide technical assistance/training to... facilities. (e) Pay the expenses associated with providing the technical assistance and/or training...

Transformation of light double cones in the human retina: the origin of trichromatism, of 4D-spatiotemporal vision, and of patchwise 4D Fourier transformation in Talbot imaging

NASA Astrophysics Data System (ADS)

Lauinger, Norbert

1997-09-01

The interpretation of the 'inverted' retina of primates as an 'optoretina' (a light cones transforming diffractive cellular 3D-phase grating) integrates the functional, structural, and oscillatory aspects of a cortical layer. It is therefore relevant to consider prenatal developments as a basis of the macro- and micro-geometry of the inner eye. This geometry becomes relevant for the postnatal trichromatic synchrony organization (TSO) as well as the adaptive levels of human vision. It is shown that the functional performances, the trichromatism in photopic vision, the monocular spatiotemporal 3D- and 4D-motion detection, as well as the Fourier optical image transformation with extraction of invariances all become possible. To transform light cones into reciprocal gratings especially the spectral phase conditions in the eikonal of the geometrical optical imaging before the retinal 3D-grating become relevant first, then in the von Laue resp. reciprocal von Laue equation for 3D-grating optics inside the grating and finally in the periodicity of Talbot-2/Fresnel-planes in the near-field behind the grating. It is becoming possible to technically realize -- at least in some specific aspects -- such a cortical optoretina sensor element with its typical hexagonal-concentric structure which leads to these visual functions.

Schooling in Times of Acceleration

ERIC Educational Resources Information Center

Buddeberg, Magdalena; Hornberg, Sabine

2017-01-01

Modern societies are characterised by forms of acceleration, which influence social processes. Sociologist Hartmut Rosa has systematised temporal structures by focusing on three categories of social acceleration: technical acceleration, acceleration of social change, and acceleration of the pace of life. All three processes of acceleration are…

Identifying Common Practice Elements to Improve Social, Emotional, and Behavioral Outcomes of Young Children in Early Childhood Classrooms.

PubMed

McLeod, Bryce D; Sutherland, Kevin S; Martinez, Ruben G; Conroy, Maureen A; Snyder, Patricia A; Southam-Gerow, Michael A

2017-02-01

Educators are increasingly being encouraged to implement evidence-based interventions and practices to address the social, emotional, and behavioral needs of young children who exhibit problem behavior in early childhood settings. Given the nature of social-emotional learning during the early childhood years and the lack of a common set of core evidence-based practices within the early childhood literature, selection of instructional practices that foster positive social, emotional, and behavioral outcomes for children in early childhood settings can be difficult. The purpose of this paper is to report findings from a study designed to identify common practice elements found in comprehensive intervention models (i.e., manualized interventions that include a number of components) or discrete practices (i.e., a specific behavior or action) designed to target social, emotional, and behavioral learning of young children who exhibit problem behavior. We conducted a systematic review of early childhood classroom interventions that had been evaluated in randomized group designs, quasi-experimental designs, and single-case experimental designs. A total of 49 published articles were identified, and an iterative process was used to identify common practice elements. The practice elements were subsequently reviewed by experts in social-emotional and behavioral interventions for young children. Twenty-four practice elements were identified and classified into content (the goal or general principle that guides a practice element) and delivery (the way in which a teacher provides instruction to the child) categories. We discuss implications that the identification of these practice elements found in the early childhood literature has for efforts to implement models and practices.

Distributional Cost-Effectiveness Analysis

PubMed Central

Asaria, Miqdad; Griffin, Susan; Cookson, Richard

2015-01-01

Distributional cost-effectiveness analysis (DCEA) is a framework for incorporating health inequality concerns into the economic evaluation of health sector interventions. In this tutorial, we describe the technical details of how to conduct DCEA, using an illustrative example comparing alternative ways of implementing the National Health Service (NHS) Bowel Cancer Screening Programme (BCSP). The 2 key stages in DCEA are 1) modeling social distributions of health associated with different interventions, and 2) evaluating social distributions of health with respect to the dual objectives of improving total population health and reducing unfair health inequality. As well as describing the technical methods used, we also identify the data requirements and the social value judgments that have to be made. Finally, we demonstrate the use of sensitivity analyses to explore the impacts of alternative modeling assumptions and social value judgments. PMID:25908564

78 FR 59342 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... related elements of logistical and program support. (iv) Military Department: Air Force (QAI) (v) Prior... contractor engineering, technical and logistics support services, and other related elements of logistical and program support. The estimated cost is $60 million. This proposed sale will contribute to the...

NASA/DoD Aerospace Knowledge Diffusion Research Project, Paper Eleven: The Voice of the User-How U.S. Aerospace Engineers and Scientists View DoD Technical Reports

DTIC Science & Technology

1991-05-01

34 (May/June 1981): 331-339. Technical Writing Teacher 4:3 (Spring 1977): 83-88. Monge, Peter R.; James D. Schriner; Bettie F. Farace ; and Dewhirst, H...Dudley; Richard D. Avery; and Edward Richard V. Farace . The Assessment of NASA Tech- M. Brown. "Satisfaction and Performance in Re- nical

Quality, Social Justice and Accountability--Crucial Determinants of Excellence in Education

ERIC Educational Resources Information Center

Rossouw, J. P.

2015-01-01

Internationally, the quality of education, social justice and accountability can be regarded as key elements of successful school systems and societies. Separately or jointly, these elements can be analysed and debated as distinct fields of study, and linked to an education system to determine the success thereof. Being a pivotal element of…

Method of Individual Forecasting of Technical State of Logging Machines

NASA Astrophysics Data System (ADS)

Kozlov, V. G.; Gulevsky, V. A.; Skrypnikov, A. V.; Logoyda, V. S.; Menzhulova, A. S.

2018-03-01

Development of the model that evaluates the possibility of failure requires the knowledge of changes’ regularities of technical condition parameters of the machines in use. To study the regularities, the need to develop stochastic models that take into account physical essence of the processes of destruction of structural elements of the machines, the technology of their production, degradation and the stochastic properties of the parameters of the technical state and the conditions and modes of operation arose.

77 FR 56743 - Federal Acquisition Regulation; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-13

... Regulation; Technical Amendments AGENCY: Department of Defense (DoD), General Services Administration (GSA... publication schedules. Please cite FAC 2005-61, Technical Amendments. SUPPLEMENTARY INFORMATION: In order to...

78 FR 6191 - Federal Acquisition Regulation; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-29

... Regulation; Technical Amendments AGENCY: Department of Defense (DoD), General Services Administration (GSA... publication schedules. Please cite FAC 2005-65, Technical Amendments. SUPPLEMENTARY INFORMATION: In order to...

NASA/DoD Aerospace Knowledge Diffusion Research Project. Report Number 6. The Relationship between the Use of U.S. Government Technical Reports by U.S. Aerospace Engineers and Scientists and Selected Institutional and Sociometric Variables

DTIC Science & Technology

1991-01-01

Peter R.; James D. Schriner; Bettie F. Farace ; and Richard V. Farace . The Assessment of NASA Technical Information. NASA CR-181367. Washington, DC... Farace ; and Richard V. Farace . The Assessment of NASA Technical Information. NASA CR-181367. Washington, DC: National Aeronautics and Space

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report No. 36: The Technical Communications Practices of US Aerospace Engineers and Scientists: Results of the Phase 1 NASA Langley Research Center Mail Survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1995-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of U.S. aerospace engineers and scientists who were assigned to the Research and Technology Group (RTG) at the NASA Langley Research Center in September 1995.

Student Achievement in Identified Workforce Clusters: Understanding Factors that Influence Student Success

ERIC Educational Resources Information Center

D'Amico, Mark M.; Morgan, Grant B.; Robertson, Thashundray C.

2011-01-01

This study blends elements from two South Carolina Technical College System initiatives--Achieving the Dream and a workforce cluster strategy. Achieving the Dream is a national non-profit organization created to help technical and community college students succeed, particularly low-income students and students of color. This initiative, combined…

Engineering an Associate Degree-Level STEM Workforce Education Curriculum

ERIC Educational Resources Information Center

Selwitz, Jason L.; Ahring, Birgitte; Garcia-Perez, Manuel; Morrison, Judith

2018-01-01

Community and technical colleges serve a vital function in STEM education by training workers for medium- and high-skilled technical careers and providing employers the labor necessary to operate and maintain thriving business ventures. A curriculum developed with the elements of a systems-based approach results in a program more relevant to the…

Posters with an artistic flair.

PubMed

Ellerbee, Susan M

2006-01-01

Posters are a popular medium used in the classroom and at conferences. Most published and Internet resources focus on the technical aspects of poster creation. The artist's perspective has rarely been addressed. The author fills that gap by presenting color theory and a balanced appearance as important elements to be considered. Specific technical and artistic considerations are presented.

Examining the Impact of Non-Technical Security Management Factors on Information Security Management in Health Informatics

ERIC Educational Resources Information Center

Imam, Abbas H.

2013-01-01

Complexity of information security has become a major issue for organizations due to incessant threats to information assets. Healthcare organizations are particularly concerned with security owing to the inherent vulnerability of sensitive information assets in health informatics. While the non-technical security management elements have been at…

Measurement of Perceived and Technical Quality of Care for Depression in Racially and Ethnically Diverse Groups.

PubMed

Leff, H Stephen; Chow, Clifton; Wieman, Dow A; Ostrow, Laysha; Cortés, Dharma E; Harris, Treniece

2016-08-01

Measurement of patient satisfaction is now considered essential for providing patient centered care and is an important tool for addressing health care disparities. However, little is known about how ethnically and racially diverse (ERD) groups differ in how they perceive quality, and widely used instruments for measuring perceived quality give little attention to cultural elements of care. This study examined the relationship between the culturally determined beliefs and expectations of four ERD groups (African Americans, Latinos, Portuguese-speakers, and Haitians, total N = 160) and the technical quality of treatment for depression provided in four "culturally-specific" primary care clinics. Using data from the Experiences of Care and Health Outcomes survey, chart reviews and focus groups, the study addressed a set of questions related to the psychometric properties of perceived care measures and the technical quality of care. The groups differed in preferred cultural elements except all preferred inclusion of religion. They did not differ in overall perceived quality. Technical quality was higher for Portuguese and Haitians than for African Americans and Latinos. Implications of group differences for measuring quality are discussed.

European Union Framework Programme 7 Building the Europe of Knowledge

NASA Astrophysics Data System (ADS)

Akkaş, Nuri

In March 2000, the Lisbon European Council set the goal of becoming by 2010 "the most competitive and dynamic knowledge-based economy in the world, capable of sustainable economic growth with more and better jobs and greater social cohesion". This was called the Lisbon Strategy. The project of creating a European Research Area (ERA) was endorsed as a central element of the Lisbon Strategy to achieve this goal. However, EU still invests too little in R & D. In 2003, top 500 private R & D spenders in EU decreased their R & D investment by 2.0%. Top 500 private R & D spenders outside EU increased their R & D investment by 3.9%. Overall R &D investments are as follows: EU: 1.96%; US: 2.59%; S. Korea: 2.91%; Japan: 3.12%. ERA is implemented through so-called Framework Programmes (FP). FP7 is proposed on the basis of a doubling of funds and the duration is 7 years (2007-13). FP7 will fund R& D projects of immediate industrial relevance & needs of industry. Projects will include both public research institutions and private companies (PPP).

Workshop on the Integration of Finite Element Modeling with Geometric Modeling

NASA Technical Reports Server (NTRS)

Wozny, Michael J.

1987-01-01

The workshop on the Integration of Finite Element Modeling with Geometric Modeling was held on 12 May 1987. It was held to discuss the geometric modeling requirements of the finite element modeling process and to better understand the technical aspects of the integration of these two areas. The 11 papers are presented except for one for which only the abstract is given.

48 CFR 35.010 - Scientific and technical reports.

Code of Federal Regulations, 2011 CFR

2011-10-01

... SPECIAL CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 35.010 Scientific and technical reports. (a) R&D contracts shall require contractors to furnish scientific and technical reports... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Scientific and technical...

48 CFR 35.010 - Scientific and technical reports.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SPECIAL CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 35.010 Scientific and technical reports. (a) R&D contracts shall require contractors to furnish scientific and technical reports... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Scientific and technical...

48 CFR 242.7400 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Contractor Facilities 242.7400 General. (a) Program managers may conclude that they need technical... manager may assign technical representatives under the procedures in 242.7401. (b) A technical representative is a representative of a DoD program, project, or system office performing non-CAS technical...

48 CFR 242.7400 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Contractor Facilities 242.7400 General. (a) Program managers may conclude that they need technical... manager may assign technical representatives under the procedures in 242.7401. (b) A technical representative is a representative of a DoD program, project, or system office performing non-CAS technical...

48 CFR 35.010 - Scientific and technical reports.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Scientific and technical... SPECIAL CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 35.010 Scientific and technical reports. (a) R&D contracts shall require contractors to furnish scientific and technical reports...

48 CFR 35.010 - Scientific and technical reports.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Scientific and technical... SPECIAL CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 35.010 Scientific and technical reports. (a) R&D contracts shall require contractors to furnish scientific and technical reports...

48 CFR 35.010 - Scientific and technical reports.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Scientific and technical... SPECIAL CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 35.010 Scientific and technical reports. (a) R&D contracts shall require contractors to furnish scientific and technical reports...

The Tolypocladium inflatum CPA element encodes a RecQ helicase-like gene.

PubMed

Kempken, Frank

2008-12-01

Previously, a repetitive CPA element was discovered in the genome of the filamentous fungus Tolypocladium inflatum; however, no further characterization was technically possible at that time. In this study, PCR amplification was used to detect a 4 kb conserved portion of the CPA element that appeared to be present in most, if not all, genomic CPA elements. The amplicons included a large open reading frame that was most similar to a RecQ helicase-like gene from Metarhizium anisopliae. The repetitive nature of the CPA element suggests that it is related to the eukaryotic Helitron class of transposable elements.

Sports Fields: A Manual for Design Construction and Maintenance.

ERIC Educational Resources Information Center

Puhalla, Jim; Krans, Jeff; Goatley, Mike

Comprehensive technical reference information is provided for those responsible for the design, construction, renovation, or maintenance of sports grounds. Chapters illustrate specific design elements of all popular sports facilities, and explain how those elements are integrated in a successful project; explore commonly encountered sports field…

GAR Global Risk Assessment

NASA Astrophysics Data System (ADS)

Maskrey, Andrew; Safaie, Sahar

2015-04-01

Disaster risk management strategies, policies and actions need to be based on evidence of current disaster loss and risk patterns, past trends and future projections, and underlying risk factors. Faced with competing demands for resources, at any level it is only possible to priorities a range of disaster risk management strategies and investments with adequate understanding of realised losses, current and future risk levels and impacts on economic growth and social wellbeing as well as cost and impact of the strategy. The mapping and understanding of the global risk landscape has been greatly enhanced by the latest iteration of the GAR Global Risk Assessment and the objective of this submission is to present the GAR global risk assessment which contributed to Global Assessment Report (GAR) 2015. This initiative which has been led by UNISDR, was conducted by a consortium of technical institutions from around the world and has covered earthquake, cyclone, riverine flood, and tsunami probabilistic risk for all countries of the world. In addition, the risks associated with volcanic ash in the Asia-Pacific region, drought in various countries in sub-Saharan Africa and climate change in a number of countries have been calculated. The presentation will share thee results as well as the experience including the challenges faced in technical elements as well as the process and recommendations for the future of such endeavour.

The state and health in France.

PubMed

Steudler, F

1986-01-01

The Health Service in France (as indeed must be the case in many other countries) has been affected by a new technical dimension, which now adds its weight to the two main criteria, social and economic, which influence health provision. In the technical domain, new methods in research and treatment have transformed the nature of medical practice, which is more and more prey to disruption at the sudden appearance of ever more complex technologies. Medical treatment can be said to have become fragmented in some sense, and the process of division of labour within medicine to have undergone considerable development. As a result of these modifications, but also because of changes in society as a whole (the ageing of the population, altered needs and expectations), the amounts spent on health provision are growing at a higher rate than the Gross Domestic Product. This is leading the participants who control and finance the system (the State, Social Security) to think in terms of selectivity and efficiency and the medical profession itself to be willing to consider the economic implications of its activities. Moreover, the Health Service is highly valued by public opinion, as shown by a number of polls. It is a major social priority for the population, represented by the health insurance organizations whose function is to make use of their funds, raised by obligatory contributions, to strive to ensure equal access for all to the most advanced treatments and techniques. It can be shown that the evolution of the Health Service has been shaped by three differing types of underlying logic: the professional (because the technical side is chiefly represented by the professionals who personify the scientific and technical aspects of health problems), the social and the economic. Until about 1968, the social and professional rationales prevailed. From then until the change in political majority that culminated in the arrival in power of the left in May 1981, economic criteria outweighted social, and the autonomy of the professionals was strongly curtailed. Finally, in the current phase, social factors tend to have priority over economic, though without their importance being overlooked, and there is an effort to group the professionals around projects aimed at fulfilling social needs and aspirations.

Intergenerational aspects of government policy under changing demographic and economic conditions.

PubMed

Boskin, M J

1987-07-01

Changing demographic and economic conditions in the US require that attention be given to some of the intergenerational equity features of government policy. In particular, social insurance programs and public debt leave public liabilities to future generations. Taken in the aggregate, the effects of rapidly rising public debt and especially social insurance programs are transferring substantial amounts of resources from younger working generations to the expanding generation of retirees. The most crucial element in evaluating the desirability of intergenerational wealth distribution in the long run is the rate of economic growth. A society's monetary, fiscal, tax, and regulatory policies can be more or less conducive to the generation of capital formation, technical change, and economic growth. Policies that influence growth and interest rates will combine with the national deficit to determine how rapidly the debt grows or shrinks. Present accounting procedures are insufficient to provide quantitative answers to the question of what is the impact of a given program on the age-specific distributions of resources. It is important to reconsider the desirability and efficiency of intergenerational redistributions of wealth in the US. It is likely that current policies are not in line with the principles of efficiency, equity, target effectiveness, and cost effectiveness.

Effective public involvement in the HoST-D Programme for dementia home care support: From proposal and design to methods of data collection (innovative practice).

PubMed

Giebel, Clarissa; Roe, Brenda; Hodgson, Anthony; Britt, David; Clarkson, Paul

2017-01-01

Public involvement is an important element in health and social care research. However, it is little evaluated in research. This paper discusses the utility and impact of public involvement of carers and people with dementia in a five-year programme on effective home support in dementia, from proposal and design to methods of data collection, and provides a useful guide for future research on how to effectively involve the public. The Home SupporT in Dementia (HoST-D) Programme comprises two elements of public involvement, a small reference group and a virtual lay advisory group. Involving carers and people with dementia is based on the six key values of involvement - respect, support, transparency, responsiveness, fairness of opportunity, and accountability. Carers and people with dementia gave opinions on study information, methods of data collection, an economic model, case vignettes, and a memory aid booklet, which were all taken into account. Public involvement has provided benefits to the programme whilst being considerate of the time constraints and geographical locations of members.

From Mephistopheles to Isaiah: Jacques Loeb, technical biology and war.

PubMed

Fangerau, Heiner

2009-04-01

In 1917, the German-American scientist Jacques Loeb (1859-1924) published a short essay, entitled 'Biology and War', that summarized his disagreement with World War I. He was deeply saddened by the break-up of the international scientific community as a consequence of the actions of bellicose politicians. These actions were in direct opposition to his efforts to promote social reform, mechanistic biology and scientific internationalism. The aim of this paper is to examine Loeb's activities aimed at these efforts before, during and after the war. It attempts to explain how Loeb's scientific work was formed, what was special about it and why it was both successful and attacked. Particular emphasis is placed on how Loeb reacted to the War and the subsequent forced disintegration of his international scientific network. Loeb's attempts to integrate his interpretation of biology into post-war Europe's approach to the life sciences is analysed in connection with his social commitment. It is argued that his emigration to the USA, the circumstances of World War I, the reaction of his German colleagues to it and the demolition of the international scientific community changed: (1) Loeb's feelings towards his old home; (2) the direction of his scientific endeavours; and (3) his engagement in science politics. His correspondence with eminent scientists from all over the world serves as a key to Loeb's efforts in the context of the social elements of scientific networks and perceptions.

Model tests of wind turbine with a vertical axis of rotation type Lenz 2

NASA Astrophysics Data System (ADS)

Zwierzchowski, Jaroslaw; Laski, Pawel Andrzej; Blasiak, Slawomir; Takosoglu, Jakub Emanuel; Pietrala, Dawid Sebastian; Bracha, Gabriel Filip; Nowakowski, Lukasz

A building design of vertical axis wind turbines (VAWT) was presented in the article. The construction and operating principle of a wind turbine were described therein. Two VAWT turbine models were compared, i.a. Darrieus and Lenz2, taking their strengths and weaknesses into consideration. 3D solid models of turbine components were presented with the use of SolidWorks software. Using CFD methods, the air flow on two aerodynamic fins, symmetrical and asymmetrical, at different angles of attack were tested. On the basis of flow simulation conducted in FlowSimulation, an asymmetrical fin was chosen as the one showing greater load bearing capacities. Due to the uncertainty of trouble-free operation of Darrieus turbine on construction elements creating the basis thereof, a 3D model of Lenz2 turbine was constructed, which is more reliable and makes turbine self-start possible. On the basis of the research, components were designed and technical docu mentation was compiled.

Risk analysis by FMEA as an element of analytical validation.

PubMed

van Leeuwen, J F; Nauta, M J; de Kaste, D; Odekerken-Rombouts, Y M C F; Oldenhof, M T; Vredenbregt, M J; Barends, D M

2009-12-05

We subjected a Near-Infrared (NIR) analytical procedure used for screening drugs on authenticity to a Failure Mode and Effects Analysis (FMEA), including technical risks as well as risks related to human failure. An FMEA team broke down the NIR analytical method into process steps and identified possible failure modes for each step. Each failure mode was ranked on estimated frequency of occurrence (O), probability that the failure would remain undetected later in the process (D) and severity (S), each on a scale of 1-10. Human errors turned out to be the most common cause of failure modes. Failure risks were calculated by Risk Priority Numbers (RPNs)=O x D x S. Failure modes with the highest RPN scores were subjected to corrective actions and the FMEA was repeated, showing reductions in RPN scores and resulting in improvement indices up to 5.0. We recommend risk analysis as an addition to the usual analytical validation, as the FMEA enabled us to detect previously unidentified risks.

[Breast cancer screening programme: a media campaign for isolated or marginalised women].

PubMed

Mansour, Z; Fleur, L; Saugeron, A M; Merle, N; Marquis, D; Lucas, C

2005-12-01

The six counties in the Provence-Alpes-Cote d'Azur region are all well-equipped to offer widespread breast cancer screening programmes. The regional technical committee for breast cancer screening has entrusted the regional health education committee (CRES) with the task of organsing an incentive campaign targeted at reaching disenfranchised or isolated women. With the collaboration of all its partners, the CRES proposed three examples of interventions: training sessions for a variety of health care professionals, publishing communication tools, and creating partnerships with the press. Financed by the state, this campaign essentially relies upon partnership mobilisation, social solidarity, interpersonal communication and the most popular and easily accessible information channels among this population group.

Evaluation of a novel waste heat recovery system for the cement industry using multi-criteria analysis (MCA) approach

NASA Astrophysics Data System (ADS)

Han, Yue; Guo, Junshan; Zheng, Wei; Ding, Junqi; Zhu, Lingkai; Che, Yongqiang; Zhang, Yanpeng

2017-12-01

Based on a novel waste heat recovery project established in a cement plant, this paper aims to evaluate the performance of the project using multi-criteria analysis (MCA) approach. Economic, environmental, social, and technical perspectives were concerned and analyzed. Different sustainability criteria and indicators related with the project were evaluated through ranking/rating process and pairwise comparison. Results have shown similar outcomes, that ten out of eleven criteria are favorable at a high standard, which reveals the project’s success. Although the project has performed so well in economic, environmental and technical terms, social aspects have some weak points, and measures should be taken to improve social benefit.

Cognitive simulation of incident risks in the structure of loading and transport enterprise

NASA Astrophysics Data System (ADS)

Shishkina, S. V.; Pristupa, Yu D.; Pavlova, L. D.; Fryanov, V. N.

2017-09-01

Organizational and technical system of a manufacturing enterprise was identified, which includes three subsystems: main production, industrial and social infrastructure. Based on the results of cognitive modeling, significant system concepts were identified that reduce the risks of incidents. The internal control influences formed in accordance with level of competence of heads of services, departments, sections, dispatchers, acting on the basis of regulations, job profiles. The second concept influencing the enterprise management system is personnel, which is assessed by the compliance of competencies of crane operators, loader operators, slingers, loaders, and acceptance/delivery agents to job responsibilities and labor functions. At a low level of professional competencies, the personnel does not fully comply with job duties and labor functions, the risk of an incident is maximal. The application of cognitive modeling allows us to identify the essential elements that ensure stable functioning of the system as a whole.

Some correlates of electronic health information management system success in nigerian teaching hospitals.

PubMed

Ojo, Adebowale I; Popoola, Sunday O

2015-01-01

Nowadays, an electronic health information management system (EHIMS) is crucial for patient care in hospitals. This paper explores the aspects and elements that contribute to the success of EHIMS in Nigerian teaching hospitals. The study adopted a survey research design. The population of study comprised 442 health information management personnel in five teaching hospitals that had implemented EHIMS in Nigeria. A self-developed questionnaire was used as an instrument for data collection. The findings revealed that there is a positive, close relationship between all the identified factors and EHIMS's success: technical factors (r = 0.564, P < 0.05); social factors (r = 0.616, P < 0.05); organizational factors (r = 0.621, P < 0.05); financial factors (r = 0.705, P < 0.05); and political factors (r = 0.589, P < 0.05). We conclude that consideration of all the identified factors was highly significant for the success of EHIMS in Nigerian teaching hospitals.

Nuclear-safety institution in France: emergence and development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vallet, B.M.

1986-01-01

This research work examines the social construction of the nuclear-safety institution in France, and the concurrent increased focus on the nuclear-risk issue. Emphasis on risk and safety, as primarily technical issues, can partly be seen as a strategy. Employed by power elites in the nuclear technostructure, this diverts emphasis away from controversial and normative questions regarding the political and social consequences of technology to questions of technology that appear to be absolute to the technology itself. Nuclear safety, which started from a preoccupation with risk related to the nuclear energy research and development process, is examined using the analytic conceptmore » of field. As a social arena patterned to achieve specific tasks, this field is dominated by a body of state engineers recognized to have high-level scientific and administrative competences. It is structured by procedures and administrative hierarchies as well as by technical rules, norms, and standards. These are formalized and rationalized through technical, economic, political, and social needs; over time; they consolidate the field into an institution. The study documents the nuclear-safety institution as an integral part of the nuclear technostructure, which has historically used the specificity of its expertise as a buffer against outside interference.« less

Using qualitative methods to understand non-technological aspects of domestic energy efficiency

NASA Astrophysics Data System (ADS)

Ambrose, Aimee Rebecca

The overall aim of the collected published works is to investigate how different policy interventions in the field of energy efficiency (including zero carbon homes, low carbon heat networks, and domestic energy efficiency schemes) are experienced and made sense of by a range of key actors. A further aim is to understand these interventions in the context of existing theories within the field of domestic energy efficiency including socio-technical theory and Actor Network Theory. More specifically, this research advances existing knowledge in the following areas: The nature of the socio-technical challenges encountered in the introduction of more energy efficient buildings, and the importance of achieving a balance between socially acceptable and technically optimal environments. (Papers 2, 3, 4, 6 and 8). The value of qualitative research in gaining a more nuanced understanding of our relationship with the home and the implications of this for domestic energy efficiency interventions and the design of low energy buildings (all papers). The influence of tenure as determinant of access to a more energy efficient home and in particular, the stubborn and complex barriers to achieving higher standards of energy performance within the private rented sector. (Papers 1, 2, 3 and 4). The significance of identity, setting and notions of home in the context of domestic energy efficiency interventions. (Papers 1 and 4). As these themes suggest, this PhD is not just concerned with carbon reduction and energy saving as technical objects, but as a way of life. More specifically, it considers the interactions between the two and contends that technical or policy instruments, no matter how sophisticated, cannot succeed if they are not compatible with our ways of life (and ways of doing businesss) or if our ways of life cannot be reasonably adapted to acoomodate them.

76 FR 72708 - Medicare Program; Renaming and Other Changes to the Advisory Panel on Hospital Outpatient Payment...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-25

.... L. Hambrick, M.D., J.D., Chair, a CMS Medical Officer. Ruth L. Bush, M.D., M.P.H. Kari S. Cornicelli..., rural or urban practice, points of view, medical or technical specialty, type of hospital, hospital... the member based upon their technical expertise in hospital payment systems; hospital medical care...

Fluid Centrality: A Social Network Analysis of Social-Technical Relations in Computer-Mediated Communication

ERIC Educational Resources Information Center

Enriquez, Judith Guevarra

2010-01-01

In this article, centrality is explored as a measure of computer-mediated communication (CMC) in networked learning. Centrality measure is quite common in performing social network analysis (SNA) and in analysing social cohesion, strength of ties and influence in CMC, and computer-supported collaborative learning research. It argues that measuring…

An Exploratory Study of Indian University Students' Use of Social Networking Web Sites: Implications for the Workplace

ERIC Educational Resources Information Center

Agarwal, Shailja; Mital, Monika

2009-01-01

Social networking Web sites (SNWs) are online tools that have transformed the virtual encounters of the past that were technical and impersonal to today's virtual socialization that is truly nontechnical, social, and interpersonal. This article presents an exploratory study of Indian University students' use of SNWs. The results indicated that…

Secondary Social Studies Teachers' Experiences Implementing Common Core State Literacy Standards: A Phenomenological Study

ERIC Educational Resources Information Center

Webb, Krista Faith Huskey

2014-01-01

The purpose of this phenomenological study was to examine the experiences of secondary social studies teachers who implemented Common Core State Standards for English Language Arts & Literacy in history/social studies, science and technical subjects in social studies courses requiring End of Course Tests at secondary schools in one suburban…

A Social Media Practicum: An Action-Learning Approach to Social Media Marketing and Analytics

ERIC Educational Resources Information Center

Atwong, Catherine T.

2015-01-01

To prepare students for the rapidly evolving field of digital marketing, which requires more and more technical skills every year, a social media practicum creates a learning environment in which students can apply marketing principles and become ready for collaborative work in social media marketing and analytics. Using student newspapers as…

Gender Disparity in Third World Technological, Social, and Economic Development.

ERIC Educational Resources Information Center

Akubue, Anthony I.

2001-01-01

Socialization of women in developing countries inhibits their education and employment in scientific and technical fields. This mindset perpetuates poverty and limits economic and social development. Solutions include elimination of gender bias, information dissemination, replication of successful development projects, use of role models, and…

Learning Discourse Conventions: The Socialization of Technical Writers.

ERIC Educational Resources Information Center

Katz, Susan M.

Newcomers learn about the practices and values of an organization through a process called socialization. Organizational socialization research provides useful information on the strategies, such as indirect questioning and disguised conversation, that new employees can use as they move into unfamiliar settings. At one time, researchers believed…

7 CFR 1580.302 - Technical assistance and services.

Code of Federal Regulations, 2010 CFR

2010-01-01

... producers written confirmation of all technical assistance meetings. Producers shall also have access to technical information provided in writing and electronically. (d) Producers shall also be provided... 7 Agriculture 10 2010-01-01 2010-01-01 false Technical assistance and services. 1580.302 Section...

48 CFR 1252.242-73 - Contracting officer's technical representative.

Code of Federal Regulations, 2010 CFR

2010-10-01

... technical representative. 1252.242-73 Section 1252.242-73 Federal Acquisition Regulations System DEPARTMENT... and Clauses 1252.242-73 Contracting officer's technical representative. As prescribed in (TAR) 48 CFR 1242.7000(d), insert the following clause: Contracting Officer's Technical Representative (OCT 1994) (a...

48 CFR 212.211 - Technical data.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Technical data. 212.211 Section 212.211 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Acquisition of Commercial Items 212.211 Technical data. The DoD policy for acquiring technical data for...

48 CFR 212.211 - Technical data.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Technical data. 212.211 Section 212.211 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Acquisition of Commercial Items 212.211 Technical data. The DoD policy for acquiring technical data for...

48 CFR 212.211 - Technical data.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Technical data. 212.211 Section 212.211 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Acquisition of Commercial Items 212.211 Technical data. The DoD policy for acquiring technical data for...

48 CFR 212.211 - Technical data.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Technical data. 212.211 Section 212.211 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Acquisition of Commercial Items 212.211 Technical data. The DoD policy for acquiring technical data for...

48 CFR 212.211 - Technical data.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Technical data. 212.211 Section 212.211 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Acquisition of Commercial Items 212.211 Technical data. The DoD policy for acquiring technical data for...

Compilation of Cooperative Data Element Dictionary of Five Federal Agencies’ Systems for Processing of Technical Report Literature

DTIC Science & Technology

1983-03-01

investigator participated with Libary of Congress (LC) Staff and Gov- ernment Printing Office (GPO) catalogers in identifying which data elements...National Standards Institute Standard format, ANSI Z.39-2). This standard includes iden- tif ication of specific data elements by means of 3- digit tags...the closer they can come to efficient exchange. But tags assigned to the core data elements differ: they are all 3- digit tags, but the same 3 digits

Genetic Basis of Melanin Pigmentation in Butterfly Wings.

PubMed

Zhang, Linlin; Martin, Arnaud; Perry, Michael W; van der Burg, Karin R L; Matsuoka, Yuji; Monteiro, Antónia; Reed, Robert D

2017-04-01

Despite the variety, prominence, and adaptive significance of butterfly wing patterns, surprisingly little is known about the genetic basis of wing color diversity. Even though there is intense interest in wing pattern evolution and development, the technical challenge of genetically manipulating butterflies has slowed efforts to functionally characterize color pattern development genes. To identify candidate wing pigmentation genes, we used RNA sequencing to characterize transcription across multiple stages of butterfly wing development, and between different color pattern elements, in the painted lady butterfly Vanessa cardui This allowed us to pinpoint genes specifically associated with red and black pigment patterns. To test the functions of a subset of genes associated with presumptive melanin pigmentation, we used clustered regularly interspaced short palindromic repeats (CRISPR)/Cas9 genome editing in four different butterfly genera. pale , Ddc , and yellow knockouts displayed reduction of melanin pigmentation, consistent with previous findings in other insects. Interestingly, however, yellow-d , ebony , and black knockouts revealed that these genes have localized effects on tuning the color of red, brown, and ochre pattern elements. These results point to previously undescribed mechanisms for modulating the color of specific wing pattern elements in butterflies, and provide an expanded portrait of the insect melanin pathway. Copyright © 2017 by the Genetics Society of America.

Extra dimensions: 3D in PDF documentation

DOE PAGES

Graf, Norman A.

2011-01-11

Experimental science is replete with multi-dimensional information which is often poorly represented by the two dimensions of presentation slides and print media. Past efforts to disseminate such information to a wider audience have failed for a number of reasons, including a lack of standards which are easy to implement and have broad support. Adobe's Portable Document Format (PDF) has in recent years become the de facto standard for secure, dependable electronic information exchange. It has done so by creating an open format, providing support for multiple platforms and being reliable and extensible. By providing support for the ECMA standard Universalmore » 3D (U3D) file format in its free Adobe Reader software, Adobe has made it easy to distribute and interact with 3D content. By providing support for scripting and animation, temporal data can also be easily distributed to a wide, non-technical audience. We discuss how the field of radiation imaging could benefit from incorporating full 3D information about not only the detectors, but also the results of the experimental analyses, in its electronic publications. In this article, we present examples drawn from high-energy physics, mathematics and molecular biology which take advantage of this functionality. Furthermore, we demonstrate how 3D detector elements can be documented, using either CAD drawings or other sources such as GEANT visualizations as input.« less

Extra dimensions: 3D and time in PDF documentation

NASA Astrophysics Data System (ADS)

Graf, N. A.

2011-01-01

Experimental science is replete with multi-dimensional information which is often poorly represented by the two dimensions of presentation slides and print media. Past efforts to disseminate such information to a wider audience have failed for a number of reasons, including a lack of standards which are easy to implement and have broad support. Adobe's Portable Document Format (PDF) has in recent years become the de facto standard for secure, dependable electronic information exchange. It has done so by creating an open format, providing support for multiple platforms and being reliable and extensible. By providing support for the ECMA standard Universal 3D (U3D) file format in its free Adobe Reader software, Adobe has made it easy to distribute and interact with 3D content. By providing support for scripting and animation, temporal data can also be easily distributed to a wide, non-technical audience. We discuss how the field of radiation imaging could benefit from incorporating full 3D information about not only the detectors, but also the results of the experimental analyses, in its electronic publications. In this article, we present examples drawn from high-energy physics, mathematics and molecular biology which take advantage of this functionality. We demonstrate how 3D detector elements can be documented, using either CAD drawings or other sources such as GEANT visualizations as input.

Extra Dimensions: 3D and Time in PDF Documentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Graf, N.A.; /SLAC

2012-04-11

Experimental science is replete with multi-dimensional information which is often poorly represented by the two dimensions of presentation slides and print media. Past efforts to disseminate such information to a wider audience have failed for a number of reasons, including a lack of standards which are easy to implement and have broad support. Adobe's Portable Document Format (PDF) has in recent years become the de facto standard for secure, dependable electronic information exchange. It has done so by creating an open format, providing support for multiple platforms and being reliable and extensible. By providing support for the ECMA standard Universalmore » 3D (U3D) file format in its free Adobe Reader software, Adobe has made it easy to distribute and interact with 3D content. By providing support for scripting and animation, temporal data can also be easily distributed to a wide, non-technical audience. We discuss how the field of radiation imaging could benefit from incorporating full 3D information about not only the detectors, but also the results of the experimental analyses, in its electronic publications. In this article, we present examples drawn from high-energy physics, mathematics and molecular biology which take advantage of this functionality. We demonstrate how 3D detector elements can be documented, using either CAD drawings or other sources such as GEANT visualizations as input.« less

The relative contribution of physical fitness to the technical execution score in youth rhythmic gymnastics.

PubMed

Donti, Olyvia; Bogdanis, Gregory C; Kritikou, Maria; Donti, Anastasia; Theodorakou, Kalliopi

2016-06-01

This study examined the association between physical fitness and a technical execution score in rhythmic gymnasts varying in the performance level. Forty-six young rhythmic gymnasts (age: 9.9 ±1.3 years) were divided into two groups (qualifiers, n=24 and non-qualifiers, n=22) based on the results of the National Championships. Gymnasts underwent a series of physical fitness tests and technical execution was evaluated in a routine without apparatus. There were significant differences between qualifiers and non-qualifiers in the technical execution score (p=0.01, d=1.0), shoulder flexion (p=0.01, d=0.8), straight leg raise (p=0.004, d=0.9), sideways leg extension (p=0.002, d=0.9) and body fat (p=.021, d=0.7), but no differences were found in muscular endurance and jumping performance. The technical execution score for the non-qualifiers was significantly correlated with shoulder extension (r=0.423, p<0.05), sideways leg extension (r=0.687, p<0.01), push ups (r=0.437, p<0.05) and body fat (r=0.642, p<0.01), while there was only one significant correlation with sideways leg extension (r=0.467, p<0.05) for the qualifiers. Multiple regression analysis revealed that sideways leg extension, body fat, and push ups accounted for a large part (62.9%) of the variance in the technical execution score for the non-qualifiers, while for the qualifiers, only 37.3% of the variance in the technical execution score was accounted for by sideways leg extension and spine flexibility. In conclusion, flexibility and body composition can effectively discriminate between qualifiers and non-qualifiers in youth rhythmic gymnastics. At the lower level of performance (non-qualifiers), physical fitness seems to have a greater effect on the technical execution score.

14 CFR § 1260.11 - Evaluation and selection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... when the program office recommended funding is within twenty percent (20 percent) of the proposed... funding is submitted by the proposer for acceptance by the technical officer. However, when funding... identify the cost element(s) affected by the change in funding level. (2) The grant officer will review the...

14 CFR 1260.11 - Evaluation and selection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... when the program office recommended funding is within twenty percent (20 percent) of the proposed... funding is submitted by the proposer for acceptance by the technical officer. However, when funding... identify the cost element(s) affected by the change in funding level. (2) The grant officer will review the...

14 CFR 1260.11 - Evaluation and selection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... when the program office recommended funding is within twenty percent (20 percent) of the proposed... funding is submitted by the proposer for acceptance by the technical officer. However, when funding... identify the cost element(s) affected by the change in funding level. (2) The grant officer will review the...

75 FR 51864 - Self-Regulatory Organizations; Municipal Securities Rulemaking Board; Notice of Filing of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... decisions. Data elements with respect to the SHORT subscription service that would be provided through the... information about technical data elements to support transmission and data-integrity processes between the... for making well-informed investment decisions. Broad access to the information collected by the SHORT...

75 FR 60488 - Self-Regulatory Organizations; Municipal Securities Rulemaking Board; Order Granting Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-30

... decisions. Data elements with respect to the SHORT subscription service that would be provided through the... information about technical data elements to support transmission and data-integrity processes between the... Securities and Exchange Commission (``Commission''), pursuant to Section 19(b)(1) of the Securities [[Page...

Mammographic density estimation with automated volumetric breast density measurement.

PubMed

Ko, Su Yeon; Kim, Eun-Kyung; Kim, Min Jung; Moon, Hee Jung

2014-01-01

To compare automated volumetric breast density measurement (VBDM) with radiologists' evaluations based on the Breast Imaging Reporting and Data System (BI-RADS), and to identify the factors associated with technical failure of VBDM. In this study, 1129 women aged 19-82 years who underwent mammography from December 2011 to January 2012 were included. Breast density evaluations by radiologists based on BI-RADS and by VBDM (Volpara Version 1.5.1) were compared. The agreement in interpreting breast density between radiologists and VBDM was determined based on four density grades (D1, D2, D3, and D4) and a binary classification of fatty (D1-2) vs. dense (D3-4) breast using kappa statistics. The association between technical failure of VBDM and patient age, total breast volume, fibroglandular tissue volume, history of partial mastectomy, the frequency of mass > 3 cm, and breast density was analyzed. The agreement between breast density evaluations by radiologists and VBDM was fair (k value = 0.26) when the four density grades (D1/D2/D3/D4) were used and moderate (k value = 0.47) for the binary classification (D1-2/D3-4). Twenty-seven women (2.4%) showed failure of VBDM. Small total breast volume, history of partial mastectomy, and high breast density were significantly associated with technical failure of VBDM (p = 0.001 to 0.015). There is fair or moderate agreement in breast density evaluation between radiologists and VBDM. Technical failure of VBDM may be related to small total breast volume, a history of partial mastectomy, and high breast density.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 23: The communications practices of US aerospace engineering faculty and students: Results of the phase 3 survey

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis U.S. aerospace engineering faculty and students.

78 FR 13543 - Defense Federal Acquisition Regulation Supplement; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-28

... DEPARTMENT OF DEFENSE Defense Acquisition Regulations System 48 CFR Parts 201, 204, 215, 225, 227, 242, 245, and 252 Defense Federal Acquisition Regulation Supplement; Technical Amendments AGENCY: Defense Acquisition Regulations System, Department of Defense (DoD). ACTION: Final rule. SUMMARY: DoD is...

48 CFR 952.242-70 - Technical direction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... contract. (d) All technical direction shall be issued in writing by the COR. (e) The Contractor must... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Technical direction. 952... FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 952.242-70 Technical...

48 CFR 1852.242-70 - Technical direction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Direction (SEP 1993) (a) Performance of the work under this contract is subject to the written technical... the Contracting Officer in writing in accordance with NASA FAR Supplement 1842.270. “Technical... in writing by the COTR. (d) The Contractor shall proceed promptly with the performance of technical...

A Plan of Organization, Administration, and Elements of Finance for Vocational-Technical Adult Education, Birmingham City School System.

ERIC Educational Resources Information Center

Shelton, John Alton

Designed to help formulate a plan of organization and administration for vocational and technical education and adult education in the Birmingham, Alabama, city schools, this study entailed an extensive literature review on vocational education and administrative matters; a historical review of several Birmingham schools (Paul Hayne School,…

Fiscal Year 1986 Technical Objective Document (TOD).

DTIC Science & Technology

1986-03-01

abilties superior to other IR and manual turrets. - START DATE: FY 88 END DATE: FY 90" PROJECT TITLE: COMPOSITE METAL FIRES EE 62:06 JON: 2673XXXX...TECHNOLOGY: FIRE ELEMENT: INTERACTION DESCRIPTION (TECHNICAL OBJECTIVE) Evaluate a new series of agents "BORALONS" capable of extinguishing metal fires and...PROJECT TITLE: COMPOSITE METAL FIRES PE: 63723 JON: 2104XXXX

NASA Publications Guide for Authors

NASA Technical Reports Server (NTRS)

2015-01-01

This document presents guidelines for use by NASA authors in preparation and publication of their scientific and technical information (STI). Section 2 gives an overview. Section 2 describes types of publication. Section 3 discusses technical, data/information, and dissemination reviews. Section 4 provides recommended standards and gives the elements of a typical report. Section 5 presents miscellaneous preparation recommendations.

Exploring Electrochromics: A Series of Eye-Catching Experiments to Introduce Students to Multidisciplinary Research

ERIC Educational Resources Information Center

Small, Leo J.; Wolf, Steven; Spoerke, Erik D.

2014-01-01

Introducing students to a multidisciplinary research laboratory presents challenges in terms of learning specific technical skills and concepts but also with respect to integrating different technical elements to form a coherent picture of the research. Here we present a multidisciplinary series of experiments we have developed in the Electronic,…

Humanistic Elements in the Educational Practice at a United States Sub-Baccalaureate Technical College

ERIC Educational Resources Information Center

Chen, Peng; Schmidtke, Carsten

2017-01-01

Humanism has never been able to establish a firm place in technical education, which remains predominantly pragmatist in response to industry needs, certification requirements and educational standardisation. However, after a period of decline, humanism has made somewhat of a comeback as part of the movement toward student-centred education.…

Balancing Career and Technical Education with Academic Coursework: The Consequences for Mathematics Achievement in High School

ERIC Educational Resources Information Center

Bozick, Robert; Dalton, Benjamin

2013-01-01

Federal legislation has attempted to move career and technical education (CTE) from a segregated component of the high school curriculum to an integrated element that jointly improves both academic and career readiness. However, concerns remain about the ability of CTE to improve academic learning. Using a nationally representative sample of high…

Elements of Emotional Intelligence that Facilitate Exper-to-Peer Tacit Knowledge Transfer

ERIC Educational Resources Information Center

Berry, Catherine M.

2010-01-01

The purpose of this quantitative study was to compare the emotional intelligence competencies of a group of technical experts with high skills in problem-solving, leadership and mentoring (Group A) with a group of technical experts with lower skills in problem solving, leadership, and mentoring (Group B) at a semiconductor manufacturing factory in…