Sample records for elm fork trinity

  1. Occurrence and distribution of fecal indicator bacteria, and physical and chemical indicators of water quality in streams receiving discharge from Dallas/Fort Worth International Airport and vicinity, North-Central Texas, 2008

    USGS Publications Warehouse

    Harwell, Glenn R.; Mobley, Craig A.

    2009-01-01

    This report, done by the U.S. Geological Survey in cooperation with Dallas/Fort Worth International (DFW) Airport in 2008, describes the occurrence and distribution of fecal indicator bacteria (fecal coliform and Escherichia [E.] coli), and the physical and chemical indicators of water quality (relative to Texas Surface Water Quality Standards), in streams receiving discharge from DFW Airport and vicinity. At sampling sites in the lower West Fork Trinity River watershed during low-flow conditions, geometric mean E. coli counts for five of the eight West Fork Trinity River watershed sampling sites exceeded the Texas Commission on Environmental Quality E. coli criterion, thus not fully supporting contact recreation. Two of the five sites with geometric means that exceeded the contact recreation criterion are airport discharge sites, which here means that the major fraction of discharge at those sites is from DFW Airport. At sampling sites in the Elm Fork Trinity River watershed during low-flow conditions, geometric mean E. coli counts exceeded the geometric mean contact recreation criterion for seven (four airport, three non-airport) of 13 sampling sites. Under low-flow conditions in the lower West Fork Trinity River watershed, E. coli counts for airport discharge sites were significantly different from (lower than) E. coli counts for non-airport sites. Under low-flow conditions in the Elm Fork Trinity River watershed, there was no significant difference between E. coli counts for airport sites and non-airport sites. During stormflow conditions, fecal indicator bacteria counts at the most downstream (integrator) sites in each watershed were considerably higher than counts at those two sites during low-flow conditions. When stormflow sample counts are included with low-flow sample counts to compute a geometric mean for each site, classification changes from fully supporting to not fully supporting contact recreation on the basis of the geometric mean contact recreation criterion. All water temperature measurements at sampling sites in the lower West Fork Trinity River watershed were less than the maximum criterion for water temperature for the lower West Fork Trinity segment. Of the measurements at sampling sites in the Elm Fork Trinity River watershed, 95 percent were less than the maximum criterion for water temperature for the Elm Fork Trinity River segment. All dissolved oxygen concentrations were greater than the minimum criterion for stream segments classified as exceptional aquatic life use. Nearly all pH measurements were within the pH criterion range for the classified segments in both watersheds, except for those at one airport site. For sampling sites in the lower West Fork Trinity River watershed, all annual average dissolved solids concentrations were less than the maximum criterion for the lower West Fork Trinity segment. For sampling sites in the Elm Fork Trinity River, nine of the 13 sites (six airport, three non-airport) had annual averages that exceeded the maximum criterion for that segment. For ammonia, 23 samples from 12 different sites had concentrations that exceeded the screening level for ammonia. Of these 12 sites, only one non-airport site had more than the required number of exceedances to indicate a screening level concern. Stormflow total suspended solids concentrations were significantly higher than low-flow concentrations at the two integrator sites. For sampling sites in the lower West Fork Trinity River watershed, all annual average chloride concentrations were less than the maximum annual average chloride concentration criterion for that segment. For the 13 sampling sites in the Elm Fork Trinity River watershed, one non-airport site had an annual average concentration that exceeded the maximum annual average chloride concentration criterion for that segment.

  2. Diversions from Red River to Lake Dallas, Texas; and related channel losses, February and March 1954

    USGS Publications Warehouse

    Holland, Pat H.

    1954-01-01

    During the period Feb. 10 to Mar. 3, 19541 the City of Dallas pumped 1,363 acre-feet of water from its Red River plant into Pecan Creek (a tributary of Elm Fork Trinity River) 3.5 miles above Gainesville; 1,272 acre-feet of this diversion reached the head of Lake Dallas. Discharge records were obtained at four points along the channels. This water was transported down the channels of Pecan Creek and Elm Fork Trinity River to Lake Dallas, a distance of about 31 miles.

  3. Floods in south-central Oklahoma and north-central Texas, October 1981

    USGS Publications Warehouse

    Buckner, Harold D.; Kurklin, Joanne K.

    1984-01-01

    Substantial reductions in peak stages and discharges on the West Fork Trinity River downstream from Eagle Mountain Reservoir were attained as a result of reservoir storage. All floodwater on the Elm Fork Trinity River was contained by reservoir storage thus preventing a potentially devastating flood downstream on the Trinity River. Maximum stages and discharges and/or contents were recorded during and after this major flood at 83 gaging stations, crest-stage stations, reservoir stations, and a miscellaneous site.

  4. Environmental Impact Study of the Elm Fork Region of the Trinity River.

    DTIC Science & Technology

    1972-04-14

    uninterruptedly for two to four years would be re- quired. Especially in the latter two realms it is essential to compare annual data for several years in order to...site (Crook, 1952; Crook and Harris, 1953) located in the northeastern part of the sur- veyed area. The Wheeler site essentially has been destroyed...quarrying of raw mate- rial including quartzite and chert. These sites may be of any age for these resources were continually used. 18 oil 031 12 ELM FORK

  5. 78 FR 49735 - Intent To Prepare a Draft Environmental Impact Statement for Dam Safety Study, Lake Lewisville...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-15

    ... determine appropriate permanent methods for correcting potential problems, interim risk reduction measures... Environmental Impact Statement for Dam Safety Study, Lake Lewisville Dam, Elm Fork Trinity River, Denton County... primary purposes of the project are flood risk management, [[Page 49736

  6. Organic compounds in Elm Fork Trinity River water used for public supply near Carrollton, Texas, 2002-05

    USGS Publications Warehouse

    Ging, Patricia B.; Delzer, Gregory C.; Hamilton, Pixie A.

    2009-01-01

    Organic compounds studied in this U.S. Geological Survey (USGS) assessment generally are man-made, including pesticides, solvents, gasoline hydrocarbons, personal-care and domestic-use products, refrigerants, and propellants. A total of 103 of 277 compounds were detected at least once among the 30 samples of source water for a community water system on the Elm Fork Trinity River near Carrollton, Texas, collected approximately monthly during 2002-05. The diversity of compounds detected indicates a variety of different sources and uses (including wastewater discharge, industrial, agricultural, domestic, and others) and different pathways (including overland runoff and groundwater discharge) to drinking-water supplies. Nine compounds were detected year-round in source-water samples, including chloroform, methyl tert-butyl ether (MTBE), and selected herbicide compounds commonly used in the Trinity River Basin and in other urban areas across the United States. About 90 percent of the 42 compounds detected most frequently in source water (in at least 20 percent of the samples) also were detected most frequently in finished water (after treatment but before distribution). Concentrations for all detected compounds in source and finished water generally were less than 0.1 microgram per liter and always less than human-health benchmarks, which are available for about one-half of the detected compounds.

  7. LOOKING EASTSOUTHEAST. Showing downstream side of completed bridge, from confluence ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LOOKING EAST-SOUTHEAST. Showing downstream side of completed bridge, from confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  8. COMPLETED STRUCTURE. View is eastsoutheast of downstream side of bridge, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    COMPLETED STRUCTURE. View is east-southeast of downstream side of bridge, from beyond confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  9. 7. View to southeast. View of downstream side of bridge ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. View to southeast. View of downstream side of bridge from confluence of Trinity and South Fork Trinity Rivers. (90mm Lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  10. STEEL ERECTION. View of downstream of bridge, looking southeast from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    STEEL ERECTION. View of downstream of bridge, looking southeast from confluence of Trinity and South Fork Trinity rivers. The old suspension bridge is in background - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  11. Impact. The southwest end is down, as the buckled middle ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Impact. The southwest end is down, as the buckled middle section splashes into the river. View is to southeast from confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  12. Environmental Impact Statement, Aubrey Lake, Elm Fork, Trinity River, Texas.

    DTIC Science & Technology

    1973-01-01

    the most expensive site location studied. For recreation, site 4 is equal to sites 1 and 2, but less desirable than site 3. V- 9 ( 5 ) Summay. An...IV-3 9 . Agricultural Resources IV-3 10. Adverse Impacts on the Lewisville Lake Project IV- 4 Section V - Alternatives to the Proposed Action 1. No...Elements V- 4 e. Recreational Elements V- 5 2. Alternatives That Will Meet All of the Authorized Project Purposes V- 5 a. Alternate Damsite Locations V-6

  13. Aftermath. The remains of the southwest end of the bridge ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Aftermath. The remains of the southwest end of the bridge lie next to the southwest pier. View is south-southeast from confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  14. Dust trailing from the top chord, the bridge falls toward ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Dust trailing from the top chord, the bridge falls toward the river, as the southwest end (right) falls first. View southeast from confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  15. With water still in midflight, the northeast end of the ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    With water still in mid-flight, the northeast end of the bridge (left) nears total collapse. View is to southeast from confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  16. With deck removed and critical members severed, the bridge begins ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    With deck removed and critical members severed, the bridge begins to succumb to tractors, pulling cables attached to its downstream side. View is to the southeast from confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  17. Spray and dust hang in the air, as the demolition ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Spray and dust hang in the air, as the demolition is completed. Only the southeast pier remains standing at right. View is to southeast from confluence of Trinity and South Fork Trinity Rivers - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  18. OLD SUSPENSION BRIDGE. This view appears to be looking southeast, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    OLD SUSPENSION BRIDGE. This view appears to be looking southeast, at the downstream side of the suspension bridge, which was replaced by the South Fork Trinity River Bridge - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  19. 12. View to southwest. View along centerline from Trinity County ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    12. View to southwest. View along centerline from Trinity County side of bridge. (90mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  20. PLANT AND PIER #2 EXCAVATION. View is to the northeast, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PLANT AND PIER #2 EXCAVATION. View is to the northeast, looking from Humboldt County side of river toward Trinity County side - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  1. POURING FOOTING OF PIER #1. View is to the southwest, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    POURING FOOTING OF PIER #1. View is to the southwest, looking from Pier 2 in Trinity County toward Pier 1 in Humboldt County - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  2. LOOKING EAST. View is to the northeast along centerline of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LOOKING EAST. View is to the northeast along centerline of deck, looking from Humboldt County toward Trinity County. The old suspension bridge is still in place at right - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  3. STARTING EXCAVATION PIER 2. This view is roughly northeast, with ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    STARTING EXCAVATION PIER 2. This view is roughly northeast, with Pier 2 on the Trinity County end of the bridge. The old suspension bridge, at upper right, was upstream of new bridge - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  4. CANVAS FINISH TO REMOVE FLOAT MARKS. View is to the ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    CANVAS FINISH TO REMOVE FLOAT MARKS. View is to the northwest of deck finishing operations - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  5. 14. View to southwest. View through truss along centerline from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. View to southwest. View through truss along centerline from below deck. (65mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  6. 20. View to southeast. Aerial view of bridge in setting; ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. View to southeast. Aerial view of bridge in setting; downstream side. (135mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  7. COUNTERWEIGHT FOOTINGS ON EAST SIDE. View is to the north ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    COUNTERWEIGHT FOOTINGS ON EAST SIDE. View is to the north from the old suspension bridge - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  8. 13. View to northeast. View along centerline from Humboldt County ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. View to northeast. View along centerline from Humboldt County side of bridge. (90mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  9. JIGGER STICK USED IN ERECTION. Shown on highline, direction of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    JIGGER STICK USED IN ERECTION. Shown on highline, direction of view is probably to the north - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  10. 11. View to southeast. More distant overview of bridge in ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    11. View to southeast. More distant overview of bridge in setting; downstream side. (135mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  11. PIER 2. View is to the northeast, looking from Pier ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PIER 2. View is to the northeast, looking from Pier 1 toward Pier 2 from beneath completed bridge - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  12. 3. View to southwest. Oblique view of downstream side of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. View to southwest. Oblique view of downstream side of bridge and west pier. (135mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  13. 2. View to east. Oblique view of downstream side of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. View to east. Oblique view of downstream side of bridge and east pier. (135mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  14. 9. View to northeast. Oblique view of upstream side of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. View to northeast. Oblique view of upstream side of bridge from approximately deck level. (90mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  15. PLACING TOP CHORD CENTER PANEL. View to the northwest from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PLACING TOP CHORD CENTER PANEL. View to the northwest from the old suspension bridge. Chord members in place - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  16. 17. View to west. Detail, connection point L2 (see plans), ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. View to west. Detail, connection point L2 (see plans), from below deck. (135mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  17. 15. View to northeast. View along centerline from below deck; ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    15. View to northeast. View along centerline from below deck; detail of bent and floor beams. (65mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  18. STEEL ERECTION. View of upstream side of bridge, looking north ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    STEEL ERECTION. View of upstream side of bridge, looking north from the old suspension bridge at unjoined cantilever arms - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  19. 16. View to southsouthwest. Detail, connection point U1 (see plans), ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. View to south-southwest. Detail, connection point U1 (see plans), from below deck. (135mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  20. LOWER CHORD ERECTION. View is to northnorthwest from the old ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LOWER CHORD ERECTION. View is to north-northwest from the old suspension bridge. Chord members suspended from jigger stick - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  1. STEEL ERECTION. View is to the north from the old ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    STEEL ERECTION. View is to the north from the old suspension bridge, looking at upstream side of new bridge - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  2. 4. View to westsouthwest. Oblique view of upstream side of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. View to west-southwest. Oblique view of upstream side of bridge from approximately deck level. (90mm lens) - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  3. PLACING DIAGONALS IN CENTER PANEL. View is northnorthwest from the ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PLACING DIAGONALS IN CENTER PANEL. View is north-northwest from the old suspension bridge, looking at upstream side of new bridge - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  4. MOVING SHAFT FORMS FROM PIER #2 TO PIER #1. View ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    MOVING SHAFT FORMS FROM PIER #2 TO PIER #1. View is to the northeast, with shaft forms being moved by highline - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  5. COUNTERWEIGHT ON WEST SIDE. View is to the northwest of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    COUNTERWEIGHT ON WEST SIDE. View is to the northwest of counterweight on Humboldt County end of bridge, probably taken from the old suspension bridge - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  6. A Systems Evaluation of the Environmental Impact of the Aubrey Reservoir Project on Elm Fork of the Trinity River in North Texas.

    DTIC Science & Technology

    1972-06-01

    JUN 72 L C FITZPATRICK , R L ABSHI RE. L G KNOX D AC W 3-72-C-X052 4 mhhho hhEEE I lffllffllfNOlf NElf mohEEEEEshhhEE EhmhhEEEmhEEEE mhEmhEEEEEmhhI...C-0052, on 30 June 1972. I f’v IabnC Wer’Ye td so; itsj 81 3 3 063 - I _rj_,CLASSIFICATION OF THIS PAGE (When Dole Kntored) REPORT DOCUMENTATION PAGE...Engineers June 1972 Engineering Division, Plng Br, SWFED-P I . NUMBER OFPAGES P. 0. Box 17300, Fort Worth, Texas 76102 339 14. MONITORING AGENCY NAME

  7. PLACING TOP CHORD CENTER PANEL. View is to the northwest ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PLACING TOP CHORD CENTER PANEL. View is to the northwest from the old suspension bridge. Chord members being moved into place by jigger stick and highline - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  8. 18. View to southwest. Detail, bearing shoe, upstream side of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. View to southwest. Detail, bearing shoe, upstream side of east pier. Copy negative made from 35mm color transparency made with with 135mm lens by John Snyder, due to lack of sufficiently long lens for 4x5 camera. - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

  9. Estimated effects on water quality of Lake Houston from interbasin transfer of water from the Trinity River, Texas

    USGS Publications Warehouse

    Liscum, Fred; East, Jeffery W.

    2000-01-01

    The City of Houston is considering the transfer of water from the Trinity River to Lake Houston (on the San Jacinto River) to alleviate concerns about adequate water supplies for future water demands. The U.S. Geological Survey, in cooperation with the City of Houston, conducted a study to estimate the effects on the water quality of Lake Houston from the transfer of Trinity River water. A water-quality model, CE–QUAL–W2, was used to simulate six water-quality properties and constituents for scenarios of interbasin transfer of Trinity River water. Three scenarios involved the transferred Trinity River water augmenting streamflow in the East Fork of Lake Houston, and three scenarios involved the transferred water replacing streamflow from the West Fork of the San Jacinto River.The estimated effects on Lake Houston were determined by comparing volume-weighted daily mean water temperature, phosphorus, ammonia nitrogen, nitrite plus nitrate nitrogen, algal biomass, and dissolved oxygen simulated for each of the transfer scenarios to simulations for a base dataset. The effects of the interbasin transfer on Lake Houston do not appear to be detrimental to water temperature, ammonia nitrogen, or dissolved oxygen. Phosphorus and nitrite plus nitrate nitrogen showed fairly large changes when Trinity River water was transferred to replace West Fork San Jacinto River streamflow. Algal biomass showed large decreases when Trinity River water was transferred to augment East Fork Lake Houston streamflow and large increases when Trinity River water was transferred to replace West Fork San Jacinto River streamflow. Regardless of the scenario simulated, the model indicated that light was the limiting factor for algal biomass growth.

  10. Linking habitat quality with trophic performance of steelhead along forest gradients in the South Fork Trinity River watershed, California

    Treesearch

    Sarah G. McCarthy; Jeffrey J. Duda; John M. Emlen; Garth R. Hodgson; David A. Beauchamp

    2009-01-01

    We examined invertebrate prey, fish diet, and energy assimilation in relation to habitat variation for steelhead Oncorhynchus mykiss (anadromous rainbow trout) and rainbow trout in nine low-order tributaries of the South Fork Trinity River, northern California. These streams spanned a range of environmental conditions, which allowed us to use...

  11. Two-dimensional resistivity investigation along West Fork Trinity River, Naval Air Station-Joint Reserve Base, Carswell Field, Fort Worth, Texas, October 2004

    USGS Publications Warehouse

    Shah, Sachin D.; Stanton, Gregory P.

    2006-01-01

    Naval Air Station-Joint Reserve Base Carswell Field (NAS-JRB) at Fort Worth, Tex., constitutes a government-owned, contractor-operated facility that has been in operation since 1942. Contaminants, primarily volatile organic compounds and metals, have entered the ground-water-flow system through leakage from waste-disposal sites and manufacturing processes. Ground water flows from west to east toward the West Fork Trinity River. During October 2004, the U.S. Geological Survey conducted a two-dimensional (2D) resistivity investigation at a site along the West Fork Trinity River at the eastern boundary of NAS-JRB to characterize the distribution of subsurface resistivity. Five 2D resistivity profiles were collected, which ranged from 500 to 750 feet long and extended to a depth of 25 feet. The Goodland Limestone and the underlying Walnut Formation form a confining unit that underlies the alluvial aquifer. The top of this confining unit is the top of bedrock at NAS-JRB. The bedrock confining unit is the zone of interest because of the potential for contaminated ground water to enter the West Fork Trinity River through saturated bedrock. The study involved a capacitively-coupled resistivity survey and inverse modeling to obtain true or actual resistivity from apparent resistivity. The apparent resistivity was processed using an inverse modeling software program. The results of this program were used to generate distributions (images) of actual resistivity referred to as inverted sections or profiles. The images along the five profiles show a wide range of resistivity values. The two profiles nearest the West Fork Trinity River generally showed less resistivity than the three other profiles.

  12. Faunal assemblages and multi-scale habitat patterns in headwater tributaries of the South Fork Trinity River - an unregulated river embedded within a multiple-use landscape

    Treesearch

    H. H. Jr. Welsh; J. J. G. R. Hodgson; J. M. Emlen Duda

    2010-01-01

    Headwaters can represent 80% of stream kilometers in a watershed, and they also have unique physical and biological properties that have only recently been recognized for their importance in sustaining healthy functioning stream networks and their ecological services. We sampled 60 headwater tributaries in the South Fork Trinity River, a 2,430 km2...

  13. Environmental Assessment: Demolish 452 at Grand Forks Air Force Base

    DTIC Science & Technology

    2005-12-01

    Data Sheet MSL Mean Sea Level µg/m3 Micrograms Per Meter Cubed NAAQS National Ambient Air Quality Standards NAGPRA Native American Graves...elm, cottonwood, and green ash. Dutch elm disease has killed many of the elms. European buckthorn (a highly invasive exotic species), chokecherry...level, with local relief being less that one foot. Land at the base is relatively flat; with elevations ranging from 880 to 920 ft mean sea level (MSL

  14. Quantifying forest vertical structure to determine bird habitat quality in the Greenbelt Corridor, Denton, TX

    NASA Astrophysics Data System (ADS)

    Matsubayashi, Shiho

    This study presents the integration of light detection and range (LiDAR) and hyperspectral remote sensing to create a three-dimensional bird habitat map in the Greenbelt Corridor of the Elm Fork of the Trinity River. This map permits to examine the relationship between forest stand structure, landscape heterogeneity, and bird community composition. A biannual bird census was conducted at this site during the breeding seasons of 2009 and 2010. Census data combined with the three-dimensional map suggest that local breeding bird abundance, community structure, and spatial distribution patterns are highly influenced by vertical heterogeneity of vegetation surface. For local breeding birds, vertical heterogeneity of canopy surface within stands, connectivity to adjacent forest patches, largest forest patch index, and habitat (vegetation) types proved to be the most influential factors to determine bird community assemblages. Results also highlight the critical role of secondary forests to increase functional connectivity of forest patches. Overall, three-dimensional habitat descriptions derived from integrated LiDAR and hyperspectral data serve as a powerful bird conservation tool that shows how the distribution of bird species relates to forest composition and structure at various scales.

  15. 75 FR 25197 - Shasta Trinity National Forest, South Fork Management Unit, California Salt Timber Harvest and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-07

    ... use telecommunication devices for the deaf (TDD) may call the Federal Information Relay Service (FIRS..., Environmental Protection Information Center and Kiamath Forest Alliance. On February 5, 2010, Appeal Reviewing...

  16. Phloem Necrosis of American Elm in the Mississippi Delta

    Treesearch

    T. H. Filer

    1966-01-01

    Phloem necrosis in elms, caused by the virus Morsus ulmi Holmes, has been found at Rolling Fork, Mississippi, 60 miles northwest of Jackson and 47 miles north of Vicksburg, in the Delta hardwoods area. It was first reported in Mississippi in 1941, when it was found at Jackson, and it appeared in the northeastern part of the State in 1945.

  17. Effects of ELMs and disruptions on ITER divertor armour materials

    NASA Astrophysics Data System (ADS)

    Federici, G.; Zhitlukhin, A.; Arkhipov, N.; Giniyatulin, R.; Klimov, N.; Landman, I.; Podkovyrov, V.; Safronov, V.; Loarte, A.; Merola, M.

    2005-03-01

    This paper describes the response of plasma facing components manufactured with tungsten (macro-brush) and CFC to energy loads characteristic of Type I ELMs and disruptions in ITER, in experiments conducted (under an EU/RF collaboration) in two plasma guns (QSPA and MK-200UG) at the TRINITI institute. Targets were exposed to a series of repetitive pulses in QSPA with heat loads in a range of 1-2 MJ/m 2 lasting 0.5 ms. Moderate tungsten erosion, of less than 0.2 μm per pulse, was found for loads of ˜1.5 MJ/m 2, consistent with ELM erosion being determined by tungsten evaporation and not by melt layer displacement. At energy densities of ˜1.8 MJ/m 2 a sharp growth of tungsten erosion was measured together with intense droplet ejection. MK-200UG experiments were focused on studying mainly vapor plasma production and impurity transport during ELMs. The conditions for removal of thin metal deposits from a carbon substrate were characterized.

  18. Environmental Assessment: Construct New Pavilion Playground at Grand Forks AFB, North Dakota

    DTIC Science & Technology

    2003-07-12

    Mean Sea Level National Ambient Air Quality Standards Native American Graves Protection and Repatriation Act North Dakota North Dakota National...cottonwood, and green ash. Dutch elm disease has killed many of the elms. European buckthorn (a highly invasive exotic species), chokecherry, and...foot. Land at the base is relatively flat, with elevations ranging from 880 to 920 feet mean sea level (MSL) and averaging about 890 feet MSL. The land

  19. Spillway for Benbrook Dam, Clear Fork of the Trinity River, Texas: Model Investigation

    DTIC Science & Technology

    1949-03-01

    section at tho too of tho spillway to tho trapezoidal cross section of tho exit channel. Concreto training walls 11 ft in height will confine the...embankment sections to the spillway, thus eliminating the concreto sec- tiona . This procedure would require training walls at each abutment t o protect

  20. Computational Modeling of River Flow, Sediment Transport, and Bed Evolution Using Remotely Sensed Data

    DTIC Science & Technology

    2011-01-01

    mile reach from Lewiston Lake to the North Fork of the Trinity, which includes the sites above. As of this writing, all data has been analyzed and...collection effort, probably a bathymetric LiDAR effort on the Kootenai River near Bonner’s Ferry, Idaho . Detailed multibeam acoustic surveys already

  1. Flood on Big Fossil Creek at Haltom City near Fort Worth, Texas, in 1962

    USGS Publications Warehouse

    Montgomery, John H.; Ruggles, Frederick H.; Patterson, James Lee

    1965-01-01

    The approximate area inundated near Fort Worth, Texas, by Big Fossil Creek, during the flood of September 7, 1962, is shown on a topographic map to record the flood hazard in graphic form. Big Fossil Creek, which drains an area of 74.7 square miles, flows generally southeastward along the northeast edge of Fort Worth through Richland Hills and Haltom City, into West Fork Trinity River. The flood of September 7, 1962, the greatest in Richland Hills since at least 1900 was the result of a high rate of discharge from the area upstream from the confluence of Big Fossil Creek and Whites Branch. Greater floods are possible, but no attempt has been made to show their probable overflow limits. Future protective works may reduce the frequency of flooding in the area but will not necessarily eliminate flooding. Changes in culture such as new highways and bridges and changes in land use may influence the inundation pattern of future floods. Mapping of the West Fork Trinity River flood was beyond the scope of the Big Fossil Creek study, and is not shown.

  2. Linking habitat quality with trophic performance of steelhead along forest gradients in the South Fork Trinity River Watershed, California

    USGS Publications Warehouse

    McCarthy, Sarah G.; Duda, Jeffrey J.; Emlen, John M.; Hodgson, Garth R.; Beauchamp, David A.

    2009-01-01

    We examined invertebrate prey, fish diet, and energy assimilation in relation to habitat variation for steelhead Oncorhynchus mykiss (anadromous rainbow trout) and rainbow trout in nine low-order tributaries of the South Fork Trinity River, northern California. These streams spanned a range of environmental conditions, which allowed us to use bioenergetics modeling to determine the relative effects of forest cover, stream temperature, season, and fish age on food consumption and growth efficiency. Evidence of seasonal shifts in reliance on aquatic versus terrestrial food sources was detected among forest cover categories and fish ages, although these categories were not robust indicators of O. mykiss condition and growth efficiency. Consumption estimates were generally less than 20% of maximum consumption, and fish lost weight in some streams during summer low-flow conditions when stream temperatures exceeded 15°C. Current 100-year climate change projections for California threaten to exacerbate negative growth patterns and may undermine the productivity of this steelhead population, which is currently not listed as endangered or threatened. To demonstrate the potential effect of global warming on fish growth, we ran three climate change scenarios in two representative streams. Simulated temperature increases ranging from 1.4°C to 5.5°C during the summer and from 1.5°C to 2.9C during the winter amplified the weight loss; estimated average growth for age-1 fish was 0.4–4.5 times lower than normal (low to high estimated temperature increase) in the warm stream and 0.05–0.8 times lower in the cool stream. We conclude that feeding rate and temperature during the summer currently limit the growth and productivity of steelhead and rainbow trout in low-order streams in the South Fork Trinity River basin and predict that climate change will have detrimental effects on steelhead growth as well as on macroinvertebrate communities and stream ecosystems in general.

  3. Computational Modeling of River Flow, Sediment Transport, and Bed Evolution Using Remotely Sensed Data

    DTIC Science & Technology

    2009-01-01

    Ranch. Bathymetric LiDAR was collected over a 40-mile reach from Lewiston Lake to the North Fork of the Trinity, which includes the sites above. Initial...bathymetric LiDAR flight is planned for the Kootenai River near Bonner’s Ferry, Idaho for next year. Detailed multibeam acoustic surveys already exist for the

  4. Emergency burn rehabilitation: cost, risk, effectiveness

    Treesearch

    Scott R. Miles; Donald M. Haskins; Darrel W. Ranken

    1989-01-01

    The fires of 1987 had a heavy impact on the Hayfork Ranger District. Over 50,000 acres were burned within the South Fork Trinity River watershed, which contains an important anadromous fishery. Major problems within the burned area were found to be: (1) slopes having highly erodible soils where intense wildfire resulted in a total loss of ground cover, and (2) burnout...

  5. An Archeological Survey in the Gypsum Breaks on the Elm Fork of the Red River,

    DTIC Science & Technology

    1979-01-01

    Tamarix gallica salt cedar Salix nigra black willow Opuntia lindenheimeri prickly pear cactus* Artemisia filifolia sand sage Bouteloua gracilis blue...125 projectile points were recovered including Gary, Bonham, Hayes barbed, Alba barbed, knives, drills, scrapers, gouges, cores, grinding stones

  6. Assessment of juvenile coho salmon movement and behavior in relation to rehabilitation efforts in the Trinity River, California, using PIT tags and radiotelemetry

    USGS Publications Warehouse

    Chase, Robert; Hemphill, Nina; Beeman, John; Juhnke, Steve; Hannon, John; Jenkins, Amy M.

    2013-01-01

    Coho salmon (Oncorhynchus kisutch) of the Southern Oregon/Northern California Coast (SONCC) Evolutionarily Significant Unit (ESU) is federally listed as a threatened species. The Trinity River Restoration Program (TRRP) is rehabilitating the Trinity River to restore coho salmon (coho) and other salmonid populations. In order to evaluate the program’s actions, several studies of movements and behavior of coho in the Trinity River were conducted from 2006 to 2009, including snorkel surveys and mark-recapture techniques based on Passive Integrated Transponder (PIT) tags, elastomer tags, and radio transmitters. Catch, recapture, and condition of natural sub-yearlings, along with site fidelity and emigration of hatchery-reared yearlings in rehabilitated and reference habitats, were studied. Location was important because coho were absent from the lower controlled and rehabilitated sites most of the time. However, rehabilitation did not have a significant effect on natural coho salmon at the site level. Apparent survival of radio-tagged, hatchery-reared yearling coho released downstream from Lewiston Dam was much lower in the first 10 km downstream from the release site than in other areas between Lewiston Dam and the Klamath River estuary. Estimated survival of yearling hatchery coho salmon per 100 km down to Blake’s Riffle was estimated at 64 % over the distance of the 239 km study area. Migration primarily occurred at night in the upper Trinity River; however, as yearlings moved through the lower Trinity River towards the Klamath River, estuary nocturnal migration became less. Apparent survival was generally lowest in areas upstream from the North Fork of the Trinity River.

  7. Changes across a decade in size, growth, and body condition of western pond turtle (Actinemys marmorata) populations on free-flowing and regulated forks of the Trinity River in Northwest California.

    Treesearch

    Donald Ashton; James Bettaso; Hart Welsh

    2015-01-01

    Water diversions can disrupt flows and alter thermal regimes changing seasonal patterns that signal the onset of life-history functions of native organisms and compromise the fitness of their populations. We compared size, growth, relative mass, volumetric body condition, and reproductive status of Western Pond Turtles (Actinemys marmorata) across...

  8. Use of the routing procedure to study dye and gas transport in the West Fork Trinity River, Texas

    USGS Publications Warehouse

    Jobson, Harvey E.; Rathbun, R.E.

    1984-01-01

    Rhodamine-WT dye, ethylene, and propane were injected at three sites along a 21.6-kilometer reach of the West Fork Trinity River below Fort Worth, Texas. Complete dye concentration versus time curves and peak gas concentrations were measured at three cross sections below each injection. The peak dye concentrations were located and samples were collected at about three-hour intervals for as many as six additional cross sections. These data were analyzed to determine the longitudinal dispersion coefficients as well as the gas desorption coefficients using both standard techniques and a numerical routing procedure. The routing procedure, using a Lagrangian transport model to minimize numerical dispersion, provided better estimates of the dispersion coefficient than did the method of moments. At a steady flow of about 0.76 m2/s, the dispersion coefficient varied from about 0.7 m2/s in a reach contained within a single deep pool to about 2.0 m2/s in a reach containing riffles and small pools. The bulk desorption coefficients computed using the routing procedure and the standard peak method were essentially the same. The liquid film coefficient could also be obtained using the routing procedure. Both the bulk desorption coefficient and the liquid film coefficient were much smaller in the pooled reach than in the reaches containing riffles.

  9. Smoke from Fires in Southwestern Oregon, Northern California

    NASA Image and Video Library

    2017-12-08

    This satellite image shows smoke from several fires in Oregon and California on Aug. 2, 2015. The Moderate Resolution Imaging Spectroradiometer (MODIS) instrument that flies aboard NASA's Aqua satellite captured an image of smoke from these fires Aug. 2 at 21:05 UTC (5:05 p.m. EDT). The multiple red pixels are heat signatures detected by MODIS. The smoke appears to be a light brown color. InciWeb is an interagency all-risk incident information management system that coordinates with federal, state and local agencies to manage wildfires. In Oregon smoke from the Cable Crossing Fire, the Stouts Fire and the Potter Mountain Complex Fire commingle. The Cable Crossing Fire was reported burning on forestlands protected by the Douglas Forest Protective Association (DFPA) at approximately 3:25 p.m. on Tuesday, July 28, 2015, near Oregon Highway 138 East, near Mile Post 23, east of Glide. South of the Cable Crossing Fire is the Stouts Fire also in forestlands of the DFPA. This fire was reported on Thursday, July 30, 2015, burning approximately 11 miles east of Canyonville near the community of Milo. East of the other fires is the Potter Mountain Complex Fire. These fires are located in the Deschutes Forest consists of eight fires. According to Inciweb they were started by dry lightning on Saturday, Aug. 2, at approximately 5:30 p.m. about five miles north of Toketee Lake. In northern California, smoke from the River Complex Fire, the Fork Complex Fire and the Shf July Lightning Fire was visible in the MODIS image. The River Complex currently consists of seven reported and observed fires on the Six Rivers and Shasta Trinity National Forests. Originally identified as 18 fires, some have burned together. Inciweb noted that in the Six Rivers National Forest there are fires in the Trinity Alps Wilderness. Those fires include the Groves Fire and the Elk Fire. In the Shasta-Trinity National Forest the fires include the Happy Fire at 2,256 acres, Daily Fire at 16 acres, the Look Fire at 7 acres, Onion Fire at 136 acres and Smokey Fire at 1 acre. In the same forest, south of the River Complex is the Fork Complex fire. Inciweb reported that the Fork Complex consists of (at current count) over 40 fires, all of which were ignited by lightning between July 29 and 31, 2015. To the southwest of this complex is the Mad River Complex. This is a series of seven lightning fires that started on July 30, 2015 after a lightning storm moved through Northern California. To the east of this and the other fires, burns another near Redding, California, called the Shf July Lightning Fire. This is also under the Shasta-Trinity National Forest management. At 8 p.m. PDT on Aug. 2, Inciweb reported that approximately 15 lightning strikes occurred within 24 hours throughout the Shasta Trinity National Forest and resulted in two new fires. The Caves fire, east of Mt. Shasta, is approximately one-tenth of an acre. The Bluejay fire, east of Shasta Lake, is approximately four acres. Image credit: NASA Goddard's MODIS Rapid Response Team, Jeff Schmaltz NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

  10. Effects of ELMs on ITER divertor armour materials

    NASA Astrophysics Data System (ADS)

    Zhitlukhin, A.; Klimov, N.; Landman, I.; Linke, J.; Loarte, A.; Merola, M.; Podkovyrov, V.; Federici, G.; Bazylev, B.; Pestchanyi, S.; Safronov, V.; Hirai, T.; Maynashev, V.; Levashov, V.; Muzichenko, A.

    2007-06-01

    This paper is concerned with investigation of an erosion of the ITER-like divertor plasma facing components under plasma heat loads expected during the Type I ELMs in ITER. These experiments were carried out on plasma accelerator QSPA at the SRC RF TRINITI under EU/RF collaboration. Targets were exposed by series repeated plasma pulses with heat loads in a range of 0.5-1.5 MJ/m2 and pulse duration 0.5 ms. Erosion of CFC macrobrushes was determined mainly by sublimation of PAN-fibres that was less than 2.5 μm per pulse. The CFC erosion was negligible at the energy density less than 0.5 MJ/m2 and was increased to the average value 0.3 μm per pulse at 1.5 MJ/m2. The pure tungsten macrobrushes erosion was small in the energy range of 0.5-1.3 MJ/m2. The sharp growth of tungsten erosion and the intense droplet ejection were observed at the energy density of 1.5 MJ/m2.

  11. Recreational Appendix Report, Elm Fork Flood Control Project, Dallas and Denton Counties, Texas.

    DTIC Science & Technology

    1973-05-01

    Sambucus canadensis 9. Texas Sophora Sophora affinis It will be recognized that, among both the trees and the understory woody plants, there are a number...a new treatment plant for the Town of Flower Mound is ex- pected to come into operation in 1973 on a branch of Denton Creek. The Flower Mound Plant is...within the market area will be in the immediate vicinity of the Project. Coppell, Irving, Carrollton, Flower Mound, Lewisville, Piano and Hebron are all

  12. Rotational and accretionary evolution of the Klamath Mountains, California and Oregon, from Devonian to present time

    USGS Publications Warehouse

    Irwin, William P.; Mankinen, Edward A.

    1998-01-01

    The purpose of this report is to show graphically how the Klamath Mountains grew from a relatively small nucleus in Early Devonian time to its present size while rotating clockwise approximately 110°. This growth occurred by the addition of large tectonic slices of oceanic lithosphere, volcanic arcs, and melange during a sequence of accretionary episodes. The Klamath Mountains province consists of eight lithotectonoic units called terranes, some of which are divided into subterranes. The Eastern Klamath terrane, which was the early Paleozoic nucleus of the province, is divided into the Yreka, Trinity, and Redding subterranes. Through tectonic plate motion, usually involving subduction, the other terranes joined the early Paleozoic nucleus during seven accretionary episodes ranging in age from Early Devonian to Late Jurassic. The active terrane suture is shown for each episode by a bold black line. Much of the western boundary of the Klamath Mountains is marked by the South Fork and correlative faults along which the Klamath terranes overrode the Coast Range rocks during an eighth accretionary episode, forming the South Fork Mountain Schist in Early Cretaceous time.

  13. 45 MPH 6,000-Pound and 10,000-Pound Rough Terrain Fork Lift Truck Feasibility Study.

    DTIC Science & Technology

    1986-06-24

    Airport Post Office Box 66911 Chicago, IL 60666 NPN Security Classification of This Page REPORT DOCUMENTATION PAGE la . Report Security Classification...HOP Unausended Duadin., 20 - I: - 1 1.8 Inch RMS Road 14 la -3 * Clam C (0.93 Inch RMS) Rod w 12 10 10 Per~cent 9 P 7 U. 3 Percent 3 2 0 20 40 SPM...elm 10 67- * * 3 o *" - .2 0 20 40 W (mph) 4/2/ SOJA Figure 75. Rear Wheel Hop on Four Road Surfaces (10K RTFLT Unsuspended Baseline) " Page 93 Adding

  14. Faunal assemblages and multi-scale habitat patterns in headwater tributaries of the South Fork Trinity River - an unregulated river embedded within a multiple-use landscape

    USGS Publications Warehouse

    Welsh, H.H.; Hodgson, G.R.; Duda, J.J.; Emlen, J.M.

    2010-01-01

    Headwaters can represent 80% of stream kilometers in a watershed, and they also have unique physical and biological properties that have only recently been recognized for their importance in sustaining healthy functioning stream networks and their ecological services. We sampled 60 headwater tributaries in the South Fork Trinity River, a 2,430 km2, mostly forested, multiple-use watershed in northwestern California. Our objectives were: (1) to differentiate unique headwater types using 69 abiotic and vegetation variables measured at three spatial scales, and then to reduce these to informative subsets; (2) determine if distinct biota occupied the different tributary types; (3) determine the environmental attributes associated with the presence and abundance of these biotic assemblages; and (4) using niche modeling, determine key attribute thresholds to illustrate how these biota could be employed as metrics of system integrity and ecological services. Several taxa were sufficiently abundant and widespread to use as bio-indicators: the presence and abundance of steelhead trout (Oncorhynchus mykiss), herpetofauna (reptile and amphibian) species richness, and signal crayfish (Pacifastacus leniusculus) represented different trophic positions, value as commercial resources (steelhead), sensitivity to environmental stress (amphibians), and indicators of biodiversity (herpetofauna species richness). Herpetofauna species richness did not differ, but abundances of steelhead trout, signal crayfish, and amphibian richness all differed significantly among tributary types. Niche models indicated that distribution and abundance patterns in both riparian and aquatic environments were associated with physical and structural attributes at multiple spatial scales, both within and around reaches. The bio-indicators responded to unique sets of attributes, reflecting the high environmental heterogeneity in headwater tributaries across this large watershed. These niche attributes represented a wide range of headwater environments, indicating responses to a number of natural and anthropogenic conditions, and demonstrated the value of using a suite of bio-indicators to elucidate watershed conditions, and to examine numerous disturbances that may influence ecological integrity.

  15. The economic value of Trinity River water

    USGS Publications Warehouse

    Douglas, A.J.; Taylor, J.G.

    1999-01-01

    The Trinity River, largest tributary of the Klamath River, has its head-waters in the Trinity Alps of north-central California. After the construction of Trinity Dam in 1963, 90% of the Trinity River flow at Lewiston was moved to the Sacramento River via the Clear Creek Tunnel, a manmade conduit. Hydropower is produced at four installations along the route of Trinity River water that is diverted to the Sacramento River, and power production at three of these installations would diminish if no Trinity River water were diverted to the Sacramento River. After Trinity River water reaches the Sacramento River, it flows toward the Sacramento-San Joaquin Delta and San Francisco Bay. Trinity River water is pumped via Bureau of Reclamation canals and pumps to the northern San Joaquin Valley, where it is used for irrigated agriculture. The social cost of putting more water down the Trinity River is the sum of the value of the foregone consumer surplus from hydropower production as well as the value of the foregone irrigation water. Sharply diminished instream flows have also severely affected the size and robustness of Trinity River salmon, steelhead, shad and sturgeon runs. Survey data were used to estimate the non-market benefits of augmenting Trinity River instream flows by letting more water flow down the Trinity and moving less water to the Sacramento River. Preservation benefits for Trinity River instream flows and fish runs are $803 million per annum for the scenario that returns the most water down the Trinity River, a value that greatly exceeds the social cost estimate.The Trinity River, largest tributary of the Klamath River, has its headwaters in the Trinity Alps of north-central California. After the construction of Trinity Dam in 1963, 90% of the Trinity River flow at Lewiston was moved to the Sacramento River via the Clear Creek Tunnel, a manmade conduit. Hydropower is produced at four installations along the route of Trinity River water that is diverted to the Sacramento River, and power production at three of these installations would diminish if no Trinity River water were diverted to the Sacramento River. After Trinity River water reaches the Sacramento River, it flows toward the Sacramento-San Joaquin Delta and San Francisco Bay. Trinity River water is pumped via Bureau of Reclamation canals and pumps to the northern San Joaquin Valley, where it is used for irrigated agriculture. The social cost of putting more water down the Trinity River is the sum of the value of the foregone consumer surplus from hydropower production as well as the value of the foregone irrigation water. Sharply diminished instream flows have also severely affected the size and robustness of Trinity River salmon, steelhead, shad and sturgeon runs. Survey data were used to estimate the non-market benefits of augmenting Trinity River instream flows by letting more water flow down the Trinity and moving less water to the Sacramento River. Preservation benefits for Trinity River instream flows and fish runs are $803 million per annum for the scenario that returns the most water down the Trinity River, a value that greatly exceeds the social cost estimate.

  16. Material Surface Damage under High Pulse Loads Typical for ELM Bursts and Disruptions in ITER

    NASA Astrophysics Data System (ADS)

    Landman, I. S.; Pestchanyi, S. E.; Safronov, V. M.; Bazylev, B. N.; Garkusha, I. E.

    The divertor armour material for the tokamak ITER will probably be carbon manufactured as fibre composites (CFC) and tungsten as either brush-like structures or thin plates. Disruptive pulse loads where the heat deposition Q may reach 102 MJ/m 2 on a time scale Ïä of 3 ms, or operation in the ELMy H-mode at repetitive loads with Q âe 1/4 3 MJ/m2 and Ïä âe 1/4 0.3 ms, deteriorate armour performance. This work surveys recent numerical and experimental investigations of erosion mechanisms at these off-normal regimes carried out at FZK, TRINITI, and IPP-Kharkov. The modelling uses the anisotropic thermomechanics code PEGASUS-3D for the simulation of CFC brittle destruction, the surface melt motion code MEMOS-1.5D for tungsten targets, and the radiation-magnetohydrodynamics code FOREV-2D for calculating the plasma impact and simulating the heat loads for the ITER regime. Experiments aimed at validating these codes are being carried out at the plasma gun facilities MK-200UG, QSPA-T, and QSPA-Kh50 which produce powerful streams of hydrogen plasma with Q = 10–30 MJ/m2 and Ïä = 0.03–0.5 ms. Essential results are, for CFC targets, the experiments at high heat loads and the development of a local overheating model incorporated in PEGASUS-3D, and for the tungsten targets the analysis of evaporation- and melt motion erosion on the base of MEMOS-1.5D calculations for repetitive ELMs.

  17. Geologic Map of the Weaverville 15' Quadrangle, Trinity County, California

    USGS Publications Warehouse

    Irwin, William P.

    2009-01-01

    The Weaverville 15' quadrangle spans parts of five generally north-northwest-trending accreted terranes. From east to west, these are the Eastern Klamath, Central Metamorphic, North Fork, Eastern Hayfork, and Western Hayfork terranes. The Eastern Klamath terrane was thrust westward over the Central Metamorphic terrane during early Paleozoic (Devonian?) time and, in Early Cretaceous time (approx. 136 Ma), was intruded along its length by the massive Shasta Bally batholith. Remnants of overlap assemblages of the Early Cretaceous (Hauterivian) Great Valley sequence and the Tertiary Weaverville Formation cover nearly 10 percent of the quadrangle. The base of the Eastern Klamath terrane in the Weaverville quadrangle is a peridotite-gabbro complex that probably is correlative to the Trinity ophiolite (Ordovician), which is widely exposed farther north beyond the quadrangle. In the northeast part of the Weaverville quadrangle, the peridotite-gabbro complex is overlain by the Devonian Copley Greenstone and the Mississippian Bragdon Formation. Where these formations were intruded by the Shasta Bally batholith, they formed an aureole of gneissic and other metamorphic rocks around the batholith. Westward thrusting of the Eastern Klamath terrane over an adjacent body of mafic volcanic and overlying quartzose sedimentary rocks during Devonian time formed the Salmon Hornblende Schist and the Abrams Mica Schist of the Central Metamorphic terrane. Substantial beds of limestone in the quartzose sedimentary unit, generally found near the underlying volcanic rock, are too metamorphosed for fossils to have survived. Rb-Sr analysis of the Abrams Mica Schist indicates a metamorphic age of approx. 380 Ma. West of Weavervillle, the Oregon Mountain outlier of the Eastern Klamath terrane consists mainly of Bragdon Formation(?) and is largely separated from the underlying Central Metamorphic terrane by serpentinized peridotite that may be a remnant of the Trinity ophiolite. The North Fork terrane is faulted against the west edge of the Central Metamorphic terrane, and its northerly trend is disrupted by major left-lateral offsets along generally west-northwest-trending faults. The serpentinized peridotite-gabbro complex that forms the western base of the terrane is the Permian North Fork ophiolite, which to the east is overlain by broken formation of mafic-volcanic rocks, red chert, siliceous tuff, argillite, minor limestone, and clastic sedimentary rocks. The chert and siliceous tuff contain radiolarians of Permian and Mesozoic ages, and some are as young as Early Jurassic (Pliensbachian). Similar Pliensbachian radiolarians are found in Franciscan rocks of the Coast Ranges. The Eastern Hayfork terrane is broken formation and melange of mainly chert, sandstone, argillite, and various exotic blocks. The cherts yield radiolarians of Permian and Triassic ages but none of clearly Jurassic age. Limestone bodies of the Eastern Hayfork terrane contain Permian microfaunas of Tethyan affinity. The Western Hayfork terrane, exposed only in a small area in the southwestern part of the quadrangle, consists dominantly of mafic tuff and dark slaty argillite. Sparse paleontologic data indicate a Mesozoic age for the strata. The terrane includes small bodies of diorite that are related to the nearby Wildwood pluton of Middle Jurassic age and probably are related genetically to the stratified rocks. The terrane is interpreted to be the accreted remnants of a Middle Jurassic volcanic arc. Shortly after intrusion by Shasta Bally batholith (approx. 136 Ma), much of the southern half of the Weaverville quadrangle was overlapped by Lower Cretaceous, dominantly Hauterivian, marine strata of the Great Valley sequence, and to a lesser extent later during Oligocene and (or) Miocene time by fluvial and lacustrine deposits of the Weaverville Formation. This map of the Weaverville Quadrangle is a digital rendition of U.S. Geological Survey Miscellaneous Field

  18. Riverine based eco-tourism: Trinity River non-market benefits estimates

    USGS Publications Warehouse

    Douglas, A.J.; Taylor, J.G.

    1998-01-01

    California's Central Valley Project (CVP) was approved by voters in a statewide referendum in 1933. CVP referendum approval initiated funding for construction of important water development projects that had far reaching effects on regional water supplies. The construction of Trinity Dam in 1963 and the subsequent transbasin diversion of Trinity River flow was one of several CVP projects that had noteworthy adverse environmental and regional economic impacts. The Trinity River is the largest tributary of the Klamath River, and has its headwaters in the Trinity Alps of north-central California. After the construction of Trinity Dam in 1963, 90% of the Trinity River flow at Lewiston was moved to the Sacramento River via the Clear Creek Tunnel. Before 1963, the Trinity River was a major recreation resource of Northern California. The loss of streamflow has had a marked adverse impact on Trinity River-related recreation activities and the size and robustness of Trinity River salmon, steelhead, shad, and sturgeon runs. Trinity River water produces hydropower during its transit via Bureau of Reclamation canals and pumps to the northern San Joaquin Valley, where it is used for irrigated agriculture. The benefits provided by Trinity River instream flow-related environmental amenities were estimated with the travel cost method (TCM). Trinity River non-market benefits are about $406 million per annum, while the social cost of sending water down the Trinity River ranges from $17 to $42 million per annum, depending on the exact flow. We also discuss the relative magnitude of Trinity River survey data contingent value method (CVM) benefits estimates.

  19. 75 FR 47631 - Trinity Tank Car, Inc., a Subsidiary of Trinity Industries, Inc., Plants #19, 1200, 1017, 1110...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-06

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-72,065] Trinity Tank Car, Inc., a... workers of Trinity Tank Car, Inc., Plant 19, Longview, Texas. The notice was published in the Federal... findings, the Department is amending this certification to also include workers from Trinity Tank Car, Inc...

  20. Compilation of hydrologic data, Little Elm Creek, Trinity River basin, Texas, 1968

    USGS Publications Warehouse

    ,

    1972-01-01

    The U.S. Soil Conservation Service is actively engaged in the installation of flood and soil erosion reducing measures in Texas under the authority of "The Flood Control Act ot 1936 and 1944" and ''Watershed Protection and Flood Prevention Act" (Public Law 566), as amended. In June 1968, the Soil Conservation Service estimated approximately 3,500 structures to be physically and economically feasible for installation in Texas. As of September 30, 1968, 1,271 of these structures had been built. This watershed-development program will have varying but important effects on the surface- and ground-water resources of river basins, especially where a large number of the floodwater-retarding structures are built. Basic hydrologic data are needed to appraise the effects of the structures on water yield and the mode of occurrence of runoff. Hydrologic investigations of these small watersheds were begun by the Geological Survey in 1951 and are now being made in 11 areas (fig. 1). These studies are being made in cooperation with t he Texas Water Development Board, the Soil Conservation Service, the San Antonio River Authority, the city of Dallas, and the Tarrant County Water Control and Improvement District No. 1. The 11 study areas were choson to sample watersheds having different rainfall, topography, geology, and soils. In four of the study areas (Mukewater, North, Little Elm, and Pin Oak Creeks), streamflow and rainfall records were collected prior to construction of the floodwater-retarding structures, thus affording the opportunity for analyses to the conditions before and after" development. Structures have now been built in three of these study areas. A summary of the development of the floodwater-retarding structures on each study area as of September 30, 1968, is shown in table 1.

  1. Wildfires in California, August 17, 2015

    NASA Image and Video Library

    2017-12-08

    Very hot, dry and unstable conditions in California and across the Pacific Northwest add to the challenges facing firefighters as they battle blazes around the region. Cal Fire is urging Californians to be extremely cautious, especially for the next few days, as the current conditions increase the dangers authorities face. This image was taken by NASA-NOAA's Suomi NPP satellite's VIIRS instrument around 2145 UTC (5:45 p.m. EDT) on August 17, 2015. Northern California is seeing smoke from the River Complex, Route Complex, South Complex, Fork Complex and Mad River Complex fires combine over a large area of the Shasta-Trinity National Forest west of Redding, California, while the Rough Fire in Fresno County is spreading toward the Black Rock Reservoir, causing evacuations and road closures. Fires across the Pacific Northwest aren't limited to California. Please see the Suomi NPP VIIRS composites in NOAA View to see the growth and extent of fires over the past weeks. Credit: NASA/NOAA via NOAA Environmental Visualization Laboratory

  2. Hydrogeology and simulated groundwater flow and availability in the North Fork Red River aquifer, southwest Oklahoma, 1980–2013

    USGS Publications Warehouse

    Smith, S. Jerrod; Ellis, John H.; Wagner, Derrick L.; Peterson, Steven M.

    2017-09-28

    On September 8, 1981, the Oklahoma Water Resources Board established regulatory limits on the maximum annual yield of groundwater (343,042 acre-feet per year) and equal-proportionate-share (EPS) pumping rate (1.0 acre-foot per acre per year) for the North Fork Red River aquifer. The maximum annual yield and EPS were based on a hydrologic investigation that used a numerical groundwater-flow model to evaluate the effects of potential groundwater withdrawals on groundwater availability in the North Fork Red River aquifer. The Oklahoma Water Resources Board is statutorily required (every 20 years) to update the hydrologic investigation on which the maximum annual yield and EPS were based. Because 20 years have elapsed since the final order was issued, the U.S. Geological Survey, in cooperation with the Oklahoma Water Resources Board, conducted an updated hydrologic investigation and evaluated the effects of potential groundwater withdrawals on groundwater flow and availability in the North Fork Red River aquifer in Oklahoma. This report describes a hydrologic investigation of the North Fork Red River aquifer that includes an updated summary of the aquifer hydrogeology. As part of this investigation, groundwater flow and availability were simulated by using a numerical groundwater-flow model.The North Fork Red River aquifer in Beckham, Greer, Jackson, Kiowa, and Roger Mills Counties in Oklahoma is composed of about 777 square miles (497,582 acres) of alluvium and terrace deposits along the North Fork Red River and tributaries, including Sweetwater Creek, Elk Creek, Otter Creek, and Elm Fork Red River. The North Fork Red River is the primary source of surface-water inflow to Lake Altus, which overlies the North Fork Red River aquifer. Lake Altus is a U.S. Bureau of Reclamation reservoir with the primary purpose of supplying irrigation water to the Lugert-Altus Irrigation District.A hydrogeologic framework was developed for the North Fork Red River aquifer and included a definition of the aquifer extent and potentiometric surface, as well as a description of the textural and hydraulic properties of aquifer materials. The hydrogeologic framework was used in the construction of a numerical groundwater-flow model of the North Fork Red River aquifer described in this report. A conceptual model of aquifer inflows and outflows was developed for the North Fork Red River aquifer to constrain the construction and calibration of a numerical groundwater-flow model that reasonably represented the groundwater-flow system. The conceptual-model water budget estimated mean annual inflows to and outflows from the North Fork Red River aquifer for the period 1980–2013 and included a sub-accounting of mean annual inflows and outflows for the portions of the aquifer that were upgradient and downgradient from Lake Altus. The numerical groundwater-flow model simulated the period 1980–2013 and was calibrated to water-table-altitude observations at selected wells, monthly base flow at selected streamgages, net streambed seepage as estimated for the conceptual model, and Lake Altus stage.Groundwater-availability scenarios were performed by using the calibrated numerical groundwater-flow model to (1) estimate the EPS pumping rate that guarantees a minimum 20-, 40-, and 50-year life of the aquifer, (2) quantify the potential effects of projected well withdrawals on groundwater storage over a 50-year period, and (3) simulate the potential effects of a hypothetical (10-year) drought on base flow and groundwater storage. The results of the groundwater-availability scenarios could be used by the Oklahoma Water Resources Board to reevaluate the maximum annual yield of groundwater from the North Fork Red River aquifer.EPS scenarios for the North Fork Red River aquifer were run for periods of 20, 40, and 50 years. The 20-, 40-, and 50-year EPS pumping rates under normal recharge conditions were 0.59, 0.52, and 0.52 acre-foot per acre per year, respectively. Given the 497,582-acre aquifer area, these rates correspond to annual yields of about 294,000, 259,000, and 259,000 acre-feet per year, respectively. Groundwater storage at the end of the 20-year EPS scenario was about 951,000 acre-feet, or about 1,317,000 acre-feet (58 percent) less than the starting EPS scenario storage. This decrease in storage was equivalent to a mean water-level decline of about 22 feet. Most areas of the active alluvium near the North Fork Red River, Elk Creek, and Elm Fork Red River remained partially saturated through the end of the EPS scenario because of streambed seepage. Lake Altus storage was reduced to zero after 6–7 years of EPS pumping in each scenario.Projected 50-year pumping scenarios were used to simulate the effects of selected well withdrawal rates on groundwater storage of the North Fork Red River aquifer and base flows in the North Fork Red River upstream from Lake Altus. The effects of well withdrawals were evaluated by comparing changes in groundwater storage and base flow between four 50-year scenarios using (1) no groundwater pumping, (2) mean pumping rates for the study period (1980–2013), (3) 2013 pumping rates, and (4) increasing demand pumping rates. The increasing demand pumping rates assumed a 20.4-percent increase in pumping over 50 years based on 2010–60 demand projections for southwest Oklahoma.Groundwater storage after 50 years with no pumping was about 2,606,000 acre-feet, or 137,000 acre-feet (5.5 percent) greater than the initial groundwater storage; this groundwater storage increase is equivalent to a mean water-level increase of 2.3 feet. Groundwater storage after 50 years with the mean pumping rate for the study period (1980–2013) was about 2,476,000 acre-feet, or about 7,000 acre-feet (0.3 percent) greater than the initial groundwater storage; this groundwater storage increase is equivalent to a mean water-level increase of 0.1 foot. Groundwater storage at the end of the 50-year period with 2013 pumping rates was about 2,398,000 acre-feet, or about 70,000 acre-feet (2.8 percent) less than the initial storage; this groundwater storage decrease is equivalent to a mean water-level decline of 1.2 feet. Groundwater storage at the end of the 50-year period with increasing demand pumping rates was about 2,361,000 acre-feet, or about 107,000 acre-feet (4.3 percent) less than the initial storage; this groundwater storage decrease is equivalent to a mean water-level decline of 1.8 feet. Mean annual base flow simulated at the Carter streamgage (07301500) on North Fork Red River increased by about 4,000 acre-feet (10 percent) after 50 years with no pumping and decreased by about 5,400 acre-feet (13 percent) after 50 years with increasing demand pumping rates. Mean annual base flow simulated at the North Fork Red River inflow to Lake Altus increased by about 7,400 acre-feet (15 percent) after 50 years with no pumping and decreased by about 5,800 acre-feet (12 percent) after 50 years with increasing demand pumping rates.A hypothetical 10-year drought scenario was used to simulate the effects of a prolonged period of reduced recharge on groundwater storage and Lake Altus stage and storage. Drought effects were quantified by comparing the results of the drought scenario to those of the calibrated numerical model (no drought). To simulate the hypothetical drought, recharge in the calibrated numerical model was reduced by 50 percent during the simulated drought period (1984–1993). Groundwater storage at the end of the drought period was about 2,271,000 acre-feet, or about 426,000 acre-feet (15.8 percent) less than the groundwater storage of the calibrated numerical model. This decrease in groundwater storage is equivalent to a mean water-table-altitude decline of 7.1 feet. At the end of the 10-year hypothetical drought period, base flows at the Sweetwater (07301420), Carter (07301500), Headrick (07305000), and Snyder (07307010) streamgages had decreased by about 37, 61, 44, and 45 percent, respectively. The minimum Lake Altus storage simulated during the drought period was 403 acre-feet, which was a decline of 92 percent from the nondrought storage. Reduced base flows in the North Fork Red River were the primary cause of Lake Altus storage declines.

  3. 76 FR 70751 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-15

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  4. 76 FR 52345 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-22

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  5. 75 FR 17158 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-05

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  6. 76 FR 14044 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-15

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  7. 75 FR 70947 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-19

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  8. 76 FR 23621 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-27

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  9. 75 FR 10501 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-08

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  10. 76 FR 34248 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-13

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  11. 75 FR 51284 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-19

    ...] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California) restoration...

  12. Environmental and Cultural Resources within the Trinity River Basin

    DTIC Science & Technology

    1971-01-01

    Berimnopedia - Trinity River, Tarrant County (66) Hiorecyatia - Trinity River, Tarrant County (66) Oseillatoria - Trinity River, Tarrant County (66) Spirulina ...73, 74) have reported additional algae and fungi from North Texas waters. These species are listed below. Anabaena Anacystic Arthrospira Chroococcus

  13. 77 FR 50155 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-20

    ...-FF08EACT00] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California...

  14. 77 FR 45370 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-31

    ...-FF08EACT00] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California...

  15. 77 FR 30314 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-22

    ...-FF08EACT00] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California...

  16. 77 FR 10766 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-23

    ...-FF08EACT00] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California...

  17. 77 FR 74203 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-13

    ...-FF08EACT00] Trinity Adaptive Management Working Group AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of meeting. SUMMARY: The Trinity Adaptive Management Working Group (TAMWG) affords stakeholders the opportunity to give policy, management, and technical input concerning Trinity River (California...

  18. Investigating Vertical Mixing Between Two Carbonate Aquifers Using a Multiport Well, Central Texas

    NASA Astrophysics Data System (ADS)

    Kromann, J.; Wong, C. I.; Hunt, B.; Smith, B.; Banner, J. L.

    2011-12-01

    Determining the occurrence and extent of mixing between vertically-adjacent aquifers is critical to dual-aquifer management. This can be challenging due to variable well depths and uncertainty as to hydrostratigraphic sources of groundwater. This study uses a multiport monitor well to investigate the degree of aquifer mixing between the overlying Edwards aquifer and underlying Trinity aquifer in central Texas. The results will inform dual-aquifer management as the Trinity aquifer is being developed as an alternative water source to the Edwards aquifer due to pumping limits and projections of increasing water demand. Water levels from isolated hydrostratigraphic units (n = 19) were measured monthly in the well as climate conditions transitioned from wet to dry (Sept 2010 to May 2011). Groundwater was sampled over a two-week interval in May to June 2011. At the start of the monitoring interval, water levels were high in the Edwards and the uppermost units of the Trinity relative to the rest of the Trinity units. Water levels decreased to lower elevations, from about 635 to 585 ft-msl, under dry conditions. Water levels in the lowermost Trinity declined less, from about 630 to 620 ft-msl, under dry conditions. Two zones separating the Edwards and lowermost Trinity showed almost no head change during this period. The water-level variations between the two aquifers suggest that: i) vertical flow potential from the Edwards to the Trinity occurs during dry conditions, ii) the uppermost stratigraphic units of the Trinity and Edwards are mixing, and iii) portions of the Trinity behave as an aquitard, providing hydrologic separation between the Edwards and lowermost Trinity units. Groundwater samples indicate the presence of three distinct hydrochemical facies: Ca-HCO3 (Edwards), Ca-HCO3-SO4 (lowermost Trinity), and Ca-SO4 (Trinity-Glen Rose Fm), suggesting little vertical flow and mixing. Covariation between groundwater 87Sr/86Sr values and SO4 concentrations from units of the Edwards and lowermost Trinity units can be accounted for by a two-end-member fluid mixing model, which uses a unit from the Edwards and lowermost Trinity as end members. This may indicate that 87Sr/86Sr values and SO4 concentrations are controlled by varying extents of mixing between the two units. Groundwater from units in the Glen Rose Formation (between the Edwards and lowermost Trinity units) cannot be accounted for by this mixing process due to elevated SO4 concentrations likely associated with dissolution of evaporites. 87Sr/86Sr values of evaporites recovered from the well are consistent with 87Sr/86Sr values of groundwater from these Glen Rose units. Although the geochemical model results suggest possible mixing between the Edwards and Trinity aquifers, water-level variations and the presence of distinct hydrochemical facies indicate that vertical flow between the Edwards and Trinity is limited to the uppermost units of the Trinity. This study suggests that the Edwards aquifer and lowermost Trinity units are not likely in hydrologic communication and independent management may be possible.

  19. Geologic framework and hydrogeologic characteristics of the outcrops of the Edwards and Trinity aquifers, Medina Lake area, Texas

    USGS Publications Warehouse

    Small, Ted A.; Lambert, Rebecca B.

    1998-01-01

    The Trinity aquifer, which crops out in the northern part of the Medina Lake area and underlies the Edwards aquifer in the southern part, is much less permeable and productive than the Edwards aquifer. Where the Trinity aquifer underlies the Edwards, the Trinity acts as a lower confining unit on the Edwards.

  20. Elm genetic diversity and hybridization in the presence of Dutch elm disease

    Treesearch

    Johanne Brunet; Raymond P. Guries

    2017-01-01

    The impact of Dutch elm disease (DED) on the genetic diversity of slippery elm (Ulmus rubra) is summarized and its potential impact on the genetic diversity of other North American native elms, American elm (U. americana), rock elm (U. thomasii), winged elm (U. alata), cedar elm (

  1. Development of a geodatabase for springs within and surrounding outcrops of the Trinity aquifer in northern Bexar County, Texas, 2010-11

    USGS Publications Warehouse

    Clark, Allan K.; Pedraza, Diane E.

    2013-01-01

    Data for 141 springs within and surrounding the Trinity aquifer outcrops in northern Bexar County were compiled from existing reports and databases. These data were augmented with selected data collected onsite, including the location, discharge, and water-quality characteristics of selected springs, and were entered into the geodatabase. The Trinity aquifer in central Texas is commonly divided into the upper, middle, and lower Trinity aquifers; all of the information that was compiled pertaining to the aquifer is for the upper and middle Trinity aquifers.

  2. HOW to Differentiate Dutch Elm Disease from Elm Phloem Necrosis

    Treesearch

    Lester Paul Gibson; Arthur R. Hastings; Leon A. LeMadeliene

    1981-01-01

    Dutch elm disease (DED) and elm phloem necrosis are the two most serious diseases of elm in the United States (Figs. 1 and 2). Most native species of elm are susceptible to both diseases. Dutch elm disease is caused by a fungus, Ceratocystis u1mi (Buisman) C. Moreau, and is transmitted by two species of elm bark beetles-the smaller European elm bark beetle, Scolytus...

  3. Identifying water-quality trends in the Trinity River, Texas, USA, 1969-1992, using sediment cores from Lake Livingston

    USGS Publications Warehouse

    Van Metre, P.C.; Callender, E.

    1996-01-01

    Chemical analyses were done on cores of bottom sediment from three locations in Lake Livingston, a reservoir on the Trinity River in east Texas to identify trends in water quality in the Trinity River using the chemical record preserved in bottom sediments trapped by the reservoir. Sediment cores spanned the period from 1969, when the reservoir was impounded, to 1992, when the cores were collected. Chemical concentrations in reservoir sediment samples were compared to concentrations for 14 streambed sediment samples from the Trinity River Basin and to reported concentrations for soils in the eastern United States and shale. These comparisons indicate that sediments deposited in Lake Livingston are representative of the environmental setting of Lake Livingston within the Trinity River Basin. Vertical changes in concentrations within sediment cores indicate temporal trends of decreasing concentrations of lead, sodium, barium, and total DDT (DDT plus its metabolites DDD and DDE) in the Trinity River. Possible increasing temporal trends are indicated for chlordane and dieldrin. Each sediment-derived trend is related to trends in water quality in the Trinity River or known changes in environmental factors in its drainage basin or both.

  4. Elm genetic diversity and hybridization in the presence of Dutch elm disease

    USDA-ARS?s Scientific Manuscript database

    Dutch elm disease (DED) has devastated native North American elm species for more than 75 years. The impact of DED on the genetic diversity of one native elm species, U. rubra or slippery elm, is summarized and its potential impact on the genetic diversity of the other four North American native elm...

  5. Simulations of flow in the Edwards-Trinity aquifer system and contiguous hydraulically connected units, west-central Texas

    USGS Publications Warehouse

    Kuniansky, E.L.; Holligan, K.Q.

    1994-01-01

    The transmissivity values used in the simulations were within estimated ranges and generally are: 1,000 to 10,000 ft2/d (feet squared per day) for the Edwards-Trinity and Trinity aquifers; 100,000 to greater than 1 million ft2/d for the Edwards aquifer; and less than 500 to 10,000 ft2/d in contiguous hydraulically connected units. Simulated flow through the Edwards-Trinity aquifer system and contiguous hydraulically connected units is about 3 million acre-feet per year. Estimates of areally distributed recharge from the simulations range from 0.1 to 1 inch per year for the Edwards-Trinity aquifer and increase to 4 inches per year for the Trinity aquifer. Recharge to the Edwards aquifer occurs along streambeds that cross outcropped high-permeability rocks of the Edwards Group through joints and faults. Many of the streams are diverted completely underground during periods of no precipitation. The movement of a substantial quantity of water (about 400 cubic feet per second) from the Trinity and Edwards-Trinity aquifers into the Edwards aquifer was simulated. Results of the simulations indicate that anisotropy strongly influences flow in the Edwards aquifer. In the San Antonio and Austin areas, the Edwards aquifer is the most active part of the ground-water flow system with one-third of ground-water discharge occurring in 5 percent of the modeled area for both simulations.

  6. Dutch elm disease pathogen transmission by the banded elm bark beetle Scolytus schevyrewi

    Treesearch

    W. R. Jacobi; R. D. Koski; J. F. Negron

    2013-01-01

    Dutch Elm Disease (DED) is a vascular wilt disease of Ulmus species (elms) incited in North America primarily by the exotic fungus Ophiostoma novo-ulmi. The pathogen is transmitted via root grafts and elm bark beetle vectors, including the native North American elm bark beetle, Hylurgopinus rufipes and the exotic smaller European elm bark beetle, Scolytus multistriatus...

  7. 75 FR 34421 - Trinity County Resource Advisory Committee

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-17

    ...) met at the Trinity County Office of Education in Weaverville, California, on June 7, 2010, at 6:30 p.m...: Trinity County Office of Education, 201 Memorial Drive, Weaverville, California 96093. FOR FURTHER....us . SUPPLEMENTARY INFORMATION: The meeting was open to the public. Public input sessions were...

  8. Plasma shaping and its impact on the pedestal of ASDEX Upgrade: edge stability and inter-ELM dynamics at varied triangularity

    NASA Astrophysics Data System (ADS)

    Laggner, F. M.; Wolfrum, E.; Cavedon, M.; Dunne, M. G.; Birkenmeier, G.; Fischer, R.; Willensdorfer, M.; Aumayr, F.; The EUROfusion MST1 Team; The ASDEX Upgrade Team

    2018-04-01

    The plasma shape, in particular the triangularity (δ), impacts on the pedestal stability. A scan of δ including a variation of heating power (P heat) and gas puff was performed to study the behaviour of edge localised modes (ELMs) and the pre-ELM pedestal stability for different plasma shapes. Generally, at higher δ the pedestal top electron density (n e) is enhanced and the ELM repetition frequency (f ELM) is reduced. For all δ, the pedestal top n e is already fully established to its pre-ELM value during the initial recovery phase of the n e pedestal, which takes place immediately after the ELM crash. The lowering of the f ELM with increasing δ is related to longer pedestal recovery phases, especially the last pre-ELM phase with clamped pedestal gradients (after the recovery phases of the n e and electron temperature (T e) pedestal) is extended. In all investigated discharge intervals, the pre-ELM pedestal profiles are in agreement with peeling-ballooning (PB) theory. Over the investigated range of δ, two well-separated f ELM bands are observed in several discharge intervals. Their occurrence is linked to the inter-ELM pedestal stability. In both kinds of ELM cycles the pedestal evolves similarly, however, the ‘fast’ ELM cycle occurs before the global plasma stored energy (W MHD) increases, which then provides a stabilising effect on the pedestal, extending the inter-ELM period in the case of the ‘slow’ ELM cycle. At the end of a ‘fast’ ELM cycle the n e profile is radially shifted inwards relative to the n e profile at the end of a ‘slow’ ELM cycle, leading to a reduced pressure gradient. The appearance of two f ELM bands suggests that the pedestal becomes more likely PB unstable in certain phases of the inter-ELM evolution. Such a behaviour is possible because the evolution of the global plasma is not rigidly coupled to the evolution of the pedestal structure on the timescales of an ELM cycle.

  9. 78 FR 35312 - Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-12

    ...-FF08EACT00] Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting... Service, announce a public meeting, teleconference and web-based meeting of the Trinity Adaptive Management Working Group (TAMWG). DATES: Public meeting, Teleconference, and web-based meeting: Tuesday June...

  10. 78 FR 49281 - Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-13

    ...-FF08EACT00] Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting... Service, announce a public meeting, teleconference, and web-based meeting of the Trinity Adaptive Management Working Group (TAMWG). DATES: Public meeting, Teleconference, and web-based meeting: Tuesday...

  11. 78 FR 17226 - Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-20

    ...-FF08EACT00] Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting... Service, announce a public meeting, teleconference and web-based meeting of the Trinity Adaptive Management Working Group (TAMWG). DATES: Public meeting, Teleconference, and web-based meeting: Monday April...

  12. Proceedings of the American elm restoration workshop 2016

    Treesearch

    Cornelia C. Pinchot; Kathleen S. Knight; Linda M. Haugen; Charles E. Flower; James M. Slavicek

    2017-01-01

    Proceedings from the 2016 American Elm Restoration Workshop in Lewis Center, OH. The published proceedings include 16 papers pertaining to elm pathogens, American elm ecology, and American elm reintroduction.

  13. Modelling of edge localised modes and edge localised mode control [Modelling of ELMs and ELM control

    DOE PAGES

    Huijsmans, G. T. A.; Chang, C. S.; Ferraro, N.; ...

    2015-02-07

    Edge Localised Modes (ELMs) in ITER Q = 10 H-mode plasmas are likely to lead to large transient heat loads to the divertor. In order to avoid an ELM induced reduction of the divertor lifetime, the large ELM energy losses need to be controlled. In ITER, ELM control is foreseen using magnetic field perturbations created by in-vessel coils and the injection of small D2 pellets. ITER plasmas are characterised by low collisionality at a high density (high fraction of the Greenwald density limit). These parameters cannot simultaneously be achieved in current experiments. Thus, the extrapolation of the ELM properties andmore » the requirements for ELM control in ITER relies on the development of validated physics models and numerical simulations. Here, we describe the modelling of ELMs and ELM control methods in ITER. The aim of this paper is not a complete review on the subject of ELM and ELM control modelling but rather to describe the current status and discuss open issues.« less

  14. Edge localized mode characteristics during edge localized mode mitigation by supersonic molecular beam injection in Korea Superconducting Tokamak Advanced Research

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lee, H. Y.; Hong, J. H.; Jang, J. H.

    It has been reported that supersonic molecular beam injection (SMBI) is an effective means of edge localized mode (ELM) mitigation. This paper newly reports the changes in the ELM, plasma profiles, and fluctuation characteristics during ELM mitigation by SMBI in Korea Superconducting Tokamak Advanced Research. During the mitigated ELM phase, the ELM frequency increased by a factor of 2–3 and the ELM size, which was estimated from the D{sub α} amplitude, the fractional changes in the plasma-stored energy and the line-averaged electron density, and divertor heat flux during an ELM burst, decreased by a factor of 0.34–0.43. Reductions in themore » electron and ion temperatures rather than in the electron density were observed during the mitigated ELM phase. In the natural ELM phase, frequency chirping of the plasma fluctuations was observed before the ELM bursts; however, the ELM bursts occurred without changes in the plasma fluctuation frequency in the mitigated ELM phase.« less

  15. 78 FR 46361 - Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-31

    ...-FF08EACT00] Trinity Adaptive Management Working Group; Public Meeting, Teleconference and Web-Based Meeting... Trinity Management Council (TMC). DATES: Public meeting, Teleconference, and web-based meeting: TAMWG and..., Douglas City, CA 96024. You may participate in person or by teleconference or web-based meeting from your...

  16. Effect of pedestal fluctuation on ELM frequency in the EAST tokamak

    NASA Astrophysics Data System (ADS)

    Zhong, F. B.; Zhang, T.; Liu, Z. X.; Qu, H.; Liu, H. Q.; Li, G. Q.; Liu, Y.; Gao, W.; Duan, Y. M.; Yang, Y.; Zeng, L.; Xiang, H. M.; Geng, K. N.; Wen, F.; Zhang, S. B.; Gao, X.; the EAST Team

    2018-05-01

    The dependence of ELM frequency on heating power has been studied on the Experimental Advanced Superconducting Tokamak (EAST). It is found that the ELM frequency (f ELM) generally increases with the power through separatrix (P sep), indicating type-I ELM in these plasmas. However, there are two data points, named ‘abnormal ELM’ in the present paper, which have much lower f ELM than the ‘normal ELM’, while both types of ELM have similar ELM energy losses. The ‘abnormal ELM’ occurs at a phase with increased radiation power due to metal impurity influx events. The increased radiation power cannot explain the much lower f ELM for ‘abnormal ELM’, since the reduction of P sep is weaker than proportional to the observed reduction of the ELM frequency. The ‘abnormal ELM’ feature can be attributed to the enhanced amplitude of a coherent mode in the pedestal region. Comparing the pedestal evolutions for the two types of ELM with similar separatrix power P sep, it is actually found that the more pronounced pedestal coherent mode in the plasma with ‘abnormal ELM’ leads to a slower pressure pedestal recovery during the inter-ELM phase. This experimental result implies that the physical mechanism for ‘abnormal ELM’ is that the more pronounced pedestal fluctuation induces larger outward transport, slows down the pedestal evolution and leads to longer inter-ELM phase, i.e. lower ELM frequency.

  17. HOW to Save Dutch Elm Diseased Trees by Pruning

    Treesearch

    J.R. Allison; G.F. Gregory

    1979-01-01

    Dutch elm disease (DED), caused by the fungus, Ceratocystis ulmi, is the most devastating shade tree disease in the United States. Healthy elms can become diseased by 1) elm bark beetles that carry the fungus from elm to elm, or 2) through root grafting with already infected trees. Along with wilt symptoms, streaking (sapwood discoloration), a characteristic internal...

  18. Report from the street: elm reintroduction

    Treesearch

    Tom. Zetterstrom

    2017-01-01

    Since the introduction of Dutch elm disease (DED) to North America, heritage elm preservation was paramount, but elm restoration is held as the long-term solution. Various elm restoration efforts have been advanced and encouraged over the past half century, and all have inspired the euphoria of the "Return of the American Elm." The changing cast of characters...

  19. Dutch elm disease

    Treesearch

    James W. Walters

    1992-01-01

    Since its discovery in the United States in 1930, Dutch elm disease has killed thousands of native elms. The three native elms, American, slippery, and rock, have little or no resistance to Dutch elm disease, but individual trees within each species vary in susceptibility to the disease. The most important of these, American elm, is scattered in upland stands but is...

  20. Extreme learning machines: a new approach for modeling dissolved oxygen (DO) concentration with and without water quality variables as predictors.

    PubMed

    Heddam, Salim; Kisi, Ozgur

    2017-07-01

    In this paper, several extreme learning machine (ELM) models, including standard extreme learning machine with sigmoid activation function (S-ELM), extreme learning machine with radial basis activation function (R-ELM), online sequential extreme learning machine (OS-ELM), and optimally pruned extreme learning machine (OP-ELM), are newly applied for predicting dissolved oxygen concentration with and without water quality variables as predictors. Firstly, using data from eight United States Geological Survey (USGS) stations located in different rivers basins, USA, the S-ELM, R-ELM, OS-ELM, and OP-ELM were compared against the measured dissolved oxygen (DO) using four water quality variables, water temperature, specific conductance, turbidity, and pH, as predictors. For each station, we used data measured at an hourly time step for a period of 4 years. The dataset was divided into a training set (70%) and a validation set (30%). We selected several combinations of the water quality variables as inputs for each ELM model and six different scenarios were compared. Secondly, an attempt was made to predict DO concentration without water quality variables. To achieve this goal, we used the year numbers, 2008, 2009, etc., month numbers from (1) to (12), day numbers from (1) to (31) and hour numbers from (00:00) to (24:00) as predictors. Thirdly, the best ELM models were trained using validation dataset and tested with the training dataset. The performances of the four ELM models were evaluated using four statistical indices: the coefficient of correlation (R), the Nash-Sutcliffe efficiency (NSE), the root mean squared error (RMSE), and the mean absolute error (MAE). Results obtained from the eight stations indicated that: (i) the best results were obtained by the S-ELM, R-ELM, OS-ELM, and OP-ELM models having four water quality variables as predictors; (ii) out of eight stations, the OP-ELM performed better than the other three ELM models at seven stations while the R-ELM performed the best at one station. The OS-ELM models performed the worst and provided the lowest accuracy; (iii) for predicting DO without water quality variables, the R-ELM performed the best at seven stations followed by the S-ELM in the second place and the OP-ELM performed the worst with low accuracy; (iv) for the final application where training ELM models with validation dataset and testing with training dataset, the OP-ELM provided the best accuracy using water quality variables and the R-ELM performed the best at all eight stations without water quality variables. Fourthly, and finally, we compared the results obtained from different ELM models with those obtained using multiple linear regression (MLR) and multilayer perceptron neural network (MLPNN). Results obtained using MLPNN and MLR models reveal that: (i) using water quality variables as predictors, the MLR performed the worst and provided the lowest accuracy in all stations; (ii) MLPNN was ranked in the second place at two stations, in the third place at four stations, and finally, in the fourth place at two stations, (iii) for predicting DO without water quality variables, MLPNN is ranked in the second place at five stations, and ranked in the third, fourth, and fifth places in the remaining three stations, while MLR was ranked in the last place with very low accuracy at all stations. Overall, the results suggest that the ELM is more effective than the MLPNN and MLR for modelling DO concentration in river ecosystems.

  1. ELM: an Algorithm to Estimate the Alpha Abundance from Low-resolution Spectra

    NASA Astrophysics Data System (ADS)

    Bu, Yude; Zhao, Gang; Pan, Jingchang; Bharat Kumar, Yerra

    2016-01-01

    We have investigated a novel methodology using the extreme learning machine (ELM) algorithm to determine the α abundance of stars. Applying two methods based on the ELM algorithm—ELM+spectra and ELM+Lick indices—to the stellar spectra from the ELODIE database, we measured the α abundance with a precision better than 0.065 dex. By applying these two methods to the spectra with different signal-to-noise ratios (S/Ns) and different resolutions, we found that ELM+spectra is more robust against degraded resolution and ELM+Lick indices is more robust against variation in S/N. To further validate the performance of ELM, we applied ELM+spectra and ELM+Lick indices to SDSS spectra and estimated α abundances with a precision around 0.10 dex, which is comparable to the results given by the SEGUE Stellar Parameter Pipeline. We further applied ELM to the spectra of stars in Galactic globular clusters (M15, M13, M71) and open clusters (NGC 2420, M67, NGC 6791), and results show good agreement with previous studies (within 1σ). A comparison of the ELM with other widely used methods including support vector machine, Gaussian process regression, artificial neural networks, and linear least-squares regression shows that ELM is efficient with computational resources and more accurate than other methods.

  2. Dutch Elm Disease Control: Intensive Sanitation and Survey Economics

    Treesearch

    William N., Jr. Cannon; Jack H. Barger; David P. Worley

    1977-01-01

    Recent research has shown that prompt removal of diseased elms reduces the incidence of Dutch elm disease more than sanitation practice that allows diseased elms to remain standing into the dormant season. The key to prompt removal is repeated surveys to detect diseased elms as early as possible. Intensive sanitation can save more elms and cost less than the more...

  3. Semi-supervised and unsupervised extreme learning machines.

    PubMed

    Huang, Gao; Song, Shiji; Gupta, Jatinder N D; Wu, Cheng

    2014-12-01

    Extreme learning machines (ELMs) have proven to be efficient and effective learning mechanisms for pattern classification and regression. However, ELMs are primarily applied to supervised learning problems. Only a few existing research papers have used ELMs to explore unlabeled data. In this paper, we extend ELMs for both semi-supervised and unsupervised tasks based on the manifold regularization, thus greatly expanding the applicability of ELMs. The key advantages of the proposed algorithms are as follows: 1) both the semi-supervised ELM (SS-ELM) and the unsupervised ELM (US-ELM) exhibit learning capability and computational efficiency of ELMs; 2) both algorithms naturally handle multiclass classification or multicluster clustering; and 3) both algorithms are inductive and can handle unseen data at test time directly. Moreover, it is shown in this paper that all the supervised, semi-supervised, and unsupervised ELMs can actually be put into a unified framework. This provides new perspectives for understanding the mechanism of random feature mapping, which is the key concept in ELM theory. Empirical study on a wide range of data sets demonstrates that the proposed algorithms are competitive with the state-of-the-art semi-supervised or unsupervised learning algorithms in terms of accuracy and efficiency.

  4. Evolution patterns and parameter regimes in edge localized modes on the National Spherical Torus Experiment

    DOE Data Explorer

    Smith, D. R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Bell, R. E. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Podesta, M. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Smith, D. R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Fonck, R. J. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); McKee, G. R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Diallo, A. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Kaye, S. M. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); LeBlanc, B. P. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Sabbagh, S. A. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States)

    2015-09-01

    We implement unsupervised machine learning techniques to identify characteristic evolution patterns and associated parameter regimes in edge localized mode (ELM) events observed on the National Spherical Torus Experiment. Multi-channel, localized measurements spanning the pedestal region capture the complex evolution patterns of ELM events on Alfven timescales. Some ELM events are active for less than 100~microsec, but others persist for up to 1~ms. Also, some ELM events exhibit a single dominant perturbation, but others are oscillatory. Clustering calculations with time-series similarity metrics indicate the ELM database contains at least two and possibly three groups of ELMs with similar evolution patterns. The identified ELM groups trigger similar stored energy loss, but the groups occupy distinct parameter regimes for ELM-relevant quantities like plasma current, triangularity, and pedestal height. Notably, the pedestal electron pressure gradient is not an effective parameter for distinguishing the ELM groups, but the ELM groups segregate in terms of electron density gradient and electron temperature gradient. The ELM evolution patterns and corresponding parameter regimes can shape the formulation or validation of nonlinear ELM models. Finally, the techniques and results demonstrate an application of unsupervised machine learning at a data-rich fusion facility.

  5. FY17 ASC CSSE L2 Milestone 6018: Power Usage Characteristics of Workloads Running on Trinity.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Pedretti, Kevin

    The overall goal of this work was to utilize the Advanced Power Management (APM) capabilities of the ATS-1 Trinity platform to understand the power usage behavior of ASC workloads running on Trinity and gain insight into the potential for utilizing power management techniques on future ASC platforms.

  6. ELM mitigation with pellet ELM triggering and implications for PFCs and plasma performance in ITER

    DOE PAGES

    Baylor, Larry R.; Lang, P. T.; Allen, Steve L.; ...

    2014-10-05

    The triggering of rapid small edge localized modes (ELMs) by high frequency pellet injection has been proposed as a method to prevent large naturally occurring ELMs that can erode the ITER plasma facing components. Deuterium pellet injection has been used to successfully demonstrate the on-demand triggering of edge localized modes (ELMs) at much higher rates and with much smaller intensity than natural ELMs. The proposed hypothesis for the triggering mechanism of ELMs by pellets is the local pressure perturbation resulting from reheating of the pellet cloud that can exceed the local high-n ballooning mode threshold where the pellet is injected.more » Nonlinear MHD simulations of the pellet ELM triggering show destabilization of high-n ballooning modes by such a local pressure perturbation. A review of the recent pellet ELM triggering results from ASDEX Upgrade (AUG), DIII-D, and JET reveals that a number of uncertainties about this ELM mitigation technique still remain. These include the heat flux impact pattern on the divertor and wall from pellet triggered and natural ELMs, the necessary pellet size and injection location to reliably trigger ELMs, and the level of fueling to be expected from ELM triggering pellets and synergy with larger fueling pellets. The implications of these issues for pellet ELM mitigation in ITER and its impact on the PFCs are presented along with the design features of the pellet injection system for ITER.« less

  7. ELM mitigation with pellet ELM triggering and implications for PFCs and plasma performance in ITER

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Baylor, Larry R.; Lang, P.; Allen, S. L.

    2015-08-01

    The triggering of rapid small edge localized modes (ELMs) by high frequency pellet injection has been proposed as a method to prevent large naturally occurring ELMs that can erode the ITER plasma facing components (PFCs). Deuterium pellet injection has been used to successfully demonstrate the on-demand triggering of edge localized modes (ELMs) at much higher rates and with much smaller intensity than natural ELMs. The proposed hypothesis for the triggering mechanism of ELMs by pellets is the local pressure perturbation resulting from reheating of the pellet cloud that can exceed the local high-n ballooning mode threshold where the pellet ismore » injected. Nonlinear MHD simulations of the pellet ELM triggering show destabilization of high-n ballooning modes by such a local pressure perturbation.A review of the recent pellet ELM triggering results from ASDEX Upgrade (AUG), DIII-D, and JET reveals that a number of uncertainties about this ELM mitigation technique still remain. These include the heat flux impact pattern on the divertor and wall from pellet triggered and natural ELMs, the necessary pellet size and injection location to reliably trigger ELMs, and the level of fueling to be expected from ELM triggering pellets and synergy with larger fueling pellets. The implications of these issues for pellet ELM mitigation in ITER and its impact on the PFCs are presented along with the design features of the pellet injection system for ITER.« less

  8. (U) Status of Trinity and Crossroads Systems

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Archer, Billy Joe; Lujan, James Westley; Hemmert, K. S.

    2017-01-10

    (U) This paper provides a general overview of current and future plans for the Advanced Simulation and Computing (ASC) Advanced Technology (AT) systems fielded by the New Mexico Alliance for Computing at Extreme Scale (ACES), a collaboration between Los Alamos Laboratory and Sandia National Laboratories. Additionally, this paper touches on research of technology beyond traditional CMOS. The status of Trinity, ASCs first AT system, and Crossroads, anticipated to succeed Trinity as the third AT system in 2020 will be presented, along with initial performance studies of the Intel Knights Landing Xeon Phi processors, introduced on Trinity. The challenges and opportunitiesmore » for our production simulation codes on AT systems will also be discussed. Trinity and Crossroads are a joint procurement by ACES and Lawrence Berkeley Laboratory as part of the Alliance for application Performance at EXtreme scale (APEX) http://apex.lanl.gov.« less

  9. DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    Trinity Gas Corp. officials signed an agreement on May 20, 1997, with the Cauca Valley Corp. (CVC) allowing Trinity to use CVC data to explore for natural gas in the Cauca Valley of Colombia. CVC, Colombia`s Valle del Cauca water resources and environmental division, is evaluating Colombia`s underground water reserves to protect, control and preserve fresh water aquifers, some of which contain natural gas pockets that cause blowouts in farmers` water wells. Preparations now are underway for drilling Trinity`s first well at the Palmira 1 site on the San Jose Hacienda, the largest privately owned sugar cane plantation in themore » valley. Trinity also entered into an agreement with the Cauca Valley Natural Gas and Electricity Project to furnish natural gas, generated electricity and energy fuel for the industrial district in the region. According to this contract, many valley residents will have electric service for the first time.« less

  10. ELM: AN ALGORITHM TO ESTIMATE THE ALPHA ABUNDANCE FROM LOW-RESOLUTION SPECTRA

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bu, Yude; Zhao, Gang; Kumar, Yerra Bharat

    We have investigated a novel methodology using the extreme learning machine (ELM) algorithm to determine the α abundance of stars. Applying two methods based on the ELM algorithm—ELM+spectra and ELM+Lick indices—to the stellar spectra from the ELODIE database, we measured the α abundance with a precision better than 0.065 dex. By applying these two methods to the spectra with different signal-to-noise ratios (S/Ns) and different resolutions, we found that ELM+spectra is more robust against degraded resolution and ELM+Lick indices is more robust against variation in S/N. To further validate the performance of ELM, we applied ELM+spectra and ELM+Lick indices to SDSSmore » spectra and estimated α abundances with a precision around 0.10 dex, which is comparable to the results given by the SEGUE Stellar Parameter Pipeline. We further applied ELM to the spectra of stars in Galactic globular clusters (M15, M13, M71) and open clusters (NGC 2420, M67, NGC 6791), and results show good agreement with previous studies (within 1σ). A comparison of the ELM with other widely used methods including support vector machine, Gaussian process regression, artificial neural networks, and linear least-squares regression shows that ELM is efficient with computational resources and more accurate than other methods.« less

  11. SALMON-TRINITY ALPS WILDERNESS, CALIFORNIA.

    USGS Publications Warehouse

    Hotz, Preston E.; Thurber, Horace K.

    1984-01-01

    The Salmon-Trinity Alps Wilderness in the Klamath Mountains province occupies an area of about 648 sq mi in parts of Trinity, Siskiyou, and Humboldt Counties, northwestern California. As a result of field studies it was determined that the Salmon-Trinity Alps Wilderness has an area with substantiated potential for gold resources in known lode deposits. Small amounts of quicksilver have been produced from one mine but there is little promise for the discovery of additional mercury resources. Geochemical sampling showed that anomalously high amounts of several other metals occur in a few places, but there is little promise for the discovery of energy or mineral resources other than mercury and gold.

  12. Trinity to Trinity 1945-2015

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Moniz, Ernest; Carr, Alan; Bethe, Hans

    The Trinity Test of July 16, 1945 was the first full-scale, real-world test of a nuclear weapon; with the new Trinity supercomputer Los Alamos National Laboratory's goal is to do this virtually, in 3D. Trinity was the culmination of a fantastic effort of groundbreaking science and engineering by hundreds of men and women at Los Alamos and other Manhattan Project sites. It took them less than two years to change the world. The Laboratory is marking the 70th anniversary of the Trinity Test because it not only ushered in the Nuclear Age, but with it the origin of today’s advancedmore » supercomputing. We live in the Age of Supercomputers due in large part to nuclear weapons science here at Los Alamos. National security science, and nuclear weapons science in particular, at Los Alamos National Laboratory have provided a key motivation for the evolution of large-scale scientific computing. Beginning with the Manhattan Project there has been a constant stream of increasingly significant, complex problems in nuclear weapons science whose timely solutions demand larger and faster computers. The relationship between national security science at Los Alamos and the evolution of computing is one of interdependence.« less

  13. Trinity to Trinity 1945-2015

    ScienceCinema

    Moniz, Ernest; Carr, Alan; Bethe, Hans; Morrison, Phillip; Ramsay, Norman; Teller, Edward; Brixner, Berlyn; Archer, Bill; Agnew, Harold; Morrison, John

    2018-01-16

    The Trinity Test of July 16, 1945 was the first full-scale, real-world test of a nuclear weapon; with the new Trinity supercomputer Los Alamos National Laboratory's goal is to do this virtually, in 3D. Trinity was the culmination of a fantastic effort of groundbreaking science and engineering by hundreds of men and women at Los Alamos and other Manhattan Project sites. It took them less than two years to change the world. The Laboratory is marking the 70th anniversary of the Trinity Test because it not only ushered in the Nuclear Age, but with it the origin of today’s advanced supercomputing. We live in the Age of Supercomputers due in large part to nuclear weapons science here at Los Alamos. National security science, and nuclear weapons science in particular, at Los Alamos National Laboratory have provided a key motivation for the evolution of large-scale scientific computing. Beginning with the Manhattan Project there has been a constant stream of increasingly significant, complex problems in nuclear weapons science whose timely solutions demand larger and faster computers. The relationship between national security science at Los Alamos and the evolution of computing is one of interdependence.

  14. Reduction of ELM Intensity on DIII-D by On-demand Triggering With High Frequency Pellet Injection and Implications for ITER

    NASA Astrophysics Data System (ADS)

    Baylor, L. R.

    2012-10-01

    Deuterium pellet injection was used on the DIII-D tokamak to successfully demonstrate for the first time the on-demand triggering of ELMs at a 10x higher rate, and with much smaller intensity, than natural edge localized modes (ELMs). The triggering of small ELMs by high frequency pellet injection has been proposed as a method to prevent large ELMs that can erode the ITER plasma facing components [1]. The demonstration was made by injecting slow (<200 m/s) 1.3 mm diameter deuterium pellets at 60 Hz from the low field side in an ITER similar plasma with 5 Hz natural ELM frequency. The input power was only slightly above the H-mode threshold. Similar non-pellet discharges had ELM energy losses up to 55 kJ (˜8% of total stored energy), while the case with pellets demonstrated ELMs with an average energy loss less than 3 kJ (<1% of the total). Total divertor ELM heat flux was reduced by more than a factor of 10. Central accumulation of Ni was significantly reduced in the pellet triggered ELM case. No significant increase in density or decrease in energy confinement was observed. Stability analysis of these discharges shows that the pedestal parameters are approaching the peeling unstable region just before a natural ELM crash. In the rapid pellet small ELM case, the pedestal conditions are well within the stable region with a narrower pedestal width observed. This narrower width is consistent with a picture in which the pellets are triggering the ELMs before the width expands to the critical ELM width. Nonlinear MHD simulations of the pellet ELM triggering show destabilization of ballooning modes by a local pressure perturbation. The implications of these results for pellet ELM pacing in ITER will be discussed. 6pt [1] P.T. Lang et al., Nucl. Fusion 44, 665 (2004).

  15. Quality of water in the Trinity and Edwards aquifers, south-central Texas, 1996-98

    USGS Publications Warehouse

    Fahlquist, Lynne; Ardis, Ann F.

    2004-01-01

    During 1996–98, the U.S. Geological Survey studied surface- and ground-water quality in south-central Texas. The ground-water components included the upper and middle zones (undifferentiated) of the Trinity aquifer in the Hill Country and the unconfined part (recharge zone) and confined part (artesian zone) of the Edwards aquifer in the Balcones fault zone of the San Antonio region. The study was supplemented by information compiled from four ground-water-quality studies done during 1996–98.Trinity aquifer waters are more mineralized and contain larger dissolved solids, sulfate, and chloride concentrations compared to Edwards aquifer waters. Greater variability in water chemistry in the Trinity aquifer likely reflects the more variable lithology of the host rock. Trace elements were widely detected, mostly at small concentrations. Median total nitrogen was larger in the Edwards aquifer than in the Trinity aquifer. Ammonia nitrogen was detected more frequently and at larger concentrations in the Trinity aquifer than in the Edwards aquifer. Although some nitrate nitrogen concentrations in the Edwards aquifer exceeded a U.S. Geological Survey national background threshold concentration, no concentrations exceeded the U.S. Environmental Protection Agency public drinking-water standard.Synthetic organic compounds, such as pesticides and volatile organic compounds, were detected in the Edwards aquifer and less frequently in the Trinity aquifer, mostly at very small concentrations (less than 1 microgram per liter). These compounds were detected most frequently in urban unconfined Edwards aquifer samples. Atrazine and its breakdown product deethylatrazine were the most frequently detected pesticides, and trihalomethanes were the most frequently detected volatile organic compounds. Widespread detections of these compounds, although at small concentrations, indicate that anthropogenic activities affect ground-water quality.Radon gas was detected throughout the Trinity aquifer but not throughout the Edwards aquifer. Fourteen samples from the Trinity aquifer and 10 samples from the Edwards aquifer exceeded a proposed U.S. Environmental Protection Agency public drinking-water standard. Sources of radon in the study area might be granitic sediments underlying the Trinity aquifer and igneous intrusions in and below the Edwards aquifer.The presence of tritium in nearly all Edwards aquifer samples indicates that some component of sampled water is young (less than about 50 years), even for long flow paths in the confined zone. About one-half of the Trinity aquifer samples contained tritium, indicating that only part of the aquifer contains young water.Hydrogen and oxygen isotopes of water provide indicators of recharge sources to the Trinity and Edwards aquifers. Most ground-water samples have a meteorological isotopic signature indicating recharge as direct infiltration of water with little residence time on the land surface. Isotopic data from some samples collected from the unconfined Edwards aquifer indicate the water has undergone evaporation. At the time that ground-water samples were collected (during a drought), nearby streams were the likely sources of recharge to these wells.

  16. Community participation in fire management planning: The Trinity county fire safe council's fire plan

    Treesearch

    Yvonne Everett

    2008-01-01

    In 1999, Trinity County CA, initiated a participatory fire management planning effort. Since that time, the Trinity County Fire Safe Council has completed critical portions of a fire safe plan and has begun to implement projects defined in the plan. Completion of a GIS based, landscape scale fuels reduction element in the plan defined by volunteer fire fighters, agency...

  17. The Trinity River Greenway: A Prototype

    DTIC Science & Technology

    1972-06-01

    study have gone into the formulation of a multipurpose plan of management designed to tame the raging waters of the Trinity, subdue its flooding crests...TABLE 6 MAMMALS OF THE STUDY AREA Shorttail Shrew (Blarina brevicauda) Beaver (Castor canadensis) Least Shrew (Crytotis parva) Armadillo (Dasypjs...property resulted. The Trinity became an J :enemy, a raging torrent to be tamed and eventually subdued. Meanwhile, thoughful men began to realize that

  18. Bird monitoring as an aid to riparian restoration: Findings from the Trinity River in northwestern California

    Treesearch

    C. Klamath Bird Observatory and USFS Pacific Southwest Research Station

    2013-01-01

    The Trinity River Restoration Program began in 2000 with the goal of restoring the Trinity River's salmon and steelhead fisheries, which were severely degraded during the last half-century as a result of dams, water diversions under the Central Valley Project, and land-use practices such as gold mining. The restoration program, as outlined in the U.S. Department...

  19. Bedrock geology and hydrostratigraphy of the Edwards and Trinity aquifers within the Driftwood and Wimberley 7.5-minute quadrangles, Hays and Comal Counties, Texas

    USGS Publications Warehouse

    Clark, Allan K.; Morris, Robert R.

    2017-11-16

    The Edwards and Trinity aquifers are major sources of water in south-central Texas and are both classified as major aquifers by the State of Texas. The population in Hays and Comal Counties is rapidly growing, increasing demands on the area’s water resources. To help effectively manage the water resources in the area, refined maps and descriptions of the geologic structures and hydrostratigraphic units of the aquifers are needed. This report presents the detailed 1:24,000-scale bedrock hydrostratigraphic map as well as names and descriptions of the geologic and hydrostratigraphic units of the Driftwood and Wimberley 7.5-minute quadrangles in Hays and Comal Counties, Tex.Hydrostratigraphically, the rocks exposed in the study area represent a section of the upper confining unit to the Edwards aquifer, the Edwards aquifer, the upper zone of the Trinity aquifer, and the middle zone of the Trinity aquifer. In the study area, the Edwards aquifer is composed of the Georgetown Formation and the rocks forming the Edwards Group. The Trinity aquifer is composed of the rocks forming the Trinity Group. The Edwards and Trinity aquifers are karstic with high secondary porosity along bedding and fractures. The Del Rio Clay is a confining unit above the Edwards aquifer and does not supply appreciable amounts of water to wells in the study area.The hydrologic connection between the Edwards and Trinity aquifers and the various hydrostratigraphic units is complex because the aquifer system is a combination of the original Cretaceous depositional environment, bioturbation, primary and secondary porosity, diagenesis, and fracturing of the area from Miocene faulting. All of these factors have resulted in development of modified porosity, permeability, and transmissivity within and between the aquifers. Faulting produced highly fractured areas which allowed for rapid infiltration of water and subsequently formed solutionally enhanced fractures, bedding planes, channels, and caves that are highly permeable and transmissive. Because of faulting the juxtaposition of the aquifers and hydrostratigraphic units has resulted in areas of interconnectedness between the Edwards and Trinity aquifers and the various hydrostratigraphic units that form the aquifers.

  20. Modeling elm growth and Dutch elm disease susceptibility

    Treesearch

    Alberto Santini; Luisa Ghelardini

    2012-01-01

    Elm susceptibility to Dutch elm disease (DED) displays strong seasonal variation. The period during which elms can become infected and express DED symptoms is generally restricted to several weeks after growth resumption in spring, although it can vary among species, provenances, and environmental conditions. The reason for this phenomenon is not understood, but the...

  1. Response of smaller European elm bark beetles to pruning wounds on American elm

    Treesearch

    Jack H. Barger; William N. Cannon

    1987-01-01

    From 1982 to 1984, inflight smaller European elm bark beetles, Scolytus multistriatus, were captured on American elms, Ulmus americana, that were therapeutically pruned for Dutch elm disease control. Pruning wounds were treated with wound dressing or left untreated to determine effects of the treatments on beetle attraction....

  2. Edge-localized-modes in tokamaks

    DOE PAGES

    Leonard, Anthony W.

    2014-09-11

    Edge-localized-modes (ELMs) are a ubiquitous feature of H-mode in tokamaks. When gradients in the H-mode transport barrier grow to exceed the MHD stability limit the ELM instability grows explosively rapidly transporting energy and particles onto open field lines and material surfaces. Though ELMs provide additional particle and impurity transport through the H-mode transport barrier, enabling steady operation, the resulting heat flux transients to plasma facing surfaces project to large amplitude in future low collisionality burning plasma tokamaks. Measurements of the ELM heat flux deposition onto material surfaces in the divertor and main chamber indicate significant broadening compared to inter-ELM heatmore » flux, with a timescale for energy deposition that is consistent with sonic ion flow and numerical simulation. Comprehensive ELM simulation is highlighting the important physics processes of ELM transport including parallel transport due to magnetic reconnection and turbulence resulting from collapse of the H-mode transport barrier. As a result, encouraging prospects for ELM control and/or suppression in future tokamaks include intrinsic modes of ELM free operation, ELM triggering with frequent small pellet injection and the application of 3D magnetic fields.« less

  3. Edge-localized-modes in tokamaksa)

    NASA Astrophysics Data System (ADS)

    Leonard, A. W.

    2014-09-01

    Edge-localized-modes (ELMs) are a ubiquitous feature of H-mode in tokamaks. When gradients in the H-mode transport barrier grow to exceed the MHD stability limit the ELM instability grows explosively, rapidly transporting energy and particles onto open field lines and material surfaces. Though ELMs provide additional particle and impurity transport through the H-mode transport barrier, enabling steady operation, the resulting heat flux transients to plasma facing surfaces project to large amplitude in future low collisionality burning plasma tokamaks. Measurements of the ELM heat flux deposition onto material surfaces in the divertor and main chamber indicate significant broadening compared to inter-ELM heat flux, with a timescale for energy deposition that is consistent with sonic ion flow and numerical simulation. Comprehensive ELM simulation is highlighting the important physics processes of ELM transport including parallel transport due to magnetic reconnection and turbulence resulting from collapse of the H-mode transport barrier. Encouraging prospects for ELM control and/or suppression in future tokamaks include intrinsic modes of ELM free operation, ELM triggering with frequent small pellet injection and the application of 3D magnetic fields.

  4. Operation REDWING 1956

    DTIC Science & Technology

    1982-08-01

    AIRCRAFT UNIT Hq TAU 2 0 1 0 Eniwetok Is. 20 Mar Hq USAF Elm 0 4 0 0 Eniwetok Is. 30 Apr Hq USAF Elm 4 3 2 0 Parry Is. 30 Apr 4g Drop & Cann Elm 15 41 0...0 Eniwrv k Is. 1 5-36 16 Mar i 4 2 5-52 mqý Effects Elm 14 7 8 53 Eniwecck Is. 1 B-52 21 Mar 1 B-47 I B-57 1 B-66 2 F-84F 1 F-101 IBDA Elm 11 35 0 0...Eniwetok Is. 3 B-47 30 Apr Ionosphere Elm 6 12 0 0 Eniwetok Is. 1 C-97 30 Apr * "Navy Effects Elm 8 31 13 0 I A3D "I P2V Early Pe.ietr Elm 16 40 0 0

  5. Physics of increased edge electron temperature and density turbulence during ELM-free QH-mode operation on DIII-D

    NASA Astrophysics Data System (ADS)

    Sung, C.; Rhodes, T. L.; Staebler, G. M.; Yan, Z.; McKee, G. R.; Smith, S. P.; Osborne, T. H.; Peebles, W. A.

    2018-05-01

    For the first time, we report increased edge electron temperature and density turbulence levels ( T˜ e and n˜ e) in Edge Localized Mode free Quiescent H-mode (ELM-free QH-mode) plasmas as compared to the ELMing time period. ELMs can severely damage plasma facing components in fusion plasma devices due to their large transient energy transport, making ELM-free operation a highly sought after goal. The QH-mode is a candidate for this goal as it is ELM-free for times limited only by hardware constraints. It is found that the driving gradients decrease during the QH-mode compared to the ELMing phase, however, a significant decrease in the ExB shearing rate is also observed that taken together is consistent with the increased turbulence. These results are significant as the prediction and control of ELM-free H-mode regimes are crucial for the operation of future fusion devices such as ITER. The changes in the linear growth rates calculated by CGYRO [Candy et al., J. Comput. Phys. 324, 73 (2016)] and the measured ExB shearing rate between ELMing and QH-mode phases are qualitatively consistent with these turbulence changes. Comparison with ELMing and 3D fields ELM suppressed H-mode finds a similar increase in T˜ e and n˜ e, however, with distinctly different origins, the increased driving gradients rather than the changes in the ExB shearing rate in 3D fields ELM suppressed the H-mode. However, linear gyrokinetic calculation results are generally consistent with the increased turbulence in both ELM-controlled discharges.

  6. Integrated simulations of H-mode operation in ITER including core fuelling, divertor detachment and ELM control

    NASA Astrophysics Data System (ADS)

    Polevoi, A. R.; Loarte, A.; Dux, R.; Eich, T.; Fable, E.; Coster, D.; Maruyama, S.; Medvedev, S. Yu.; Köchl, F.; Zhogolev, V. E.

    2018-05-01

    ELM mitigation to avoid melting of the tungsten (W) divertor is one of the main factors affecting plasma fuelling and detachment control at full current for high Q operation in ITER. Here we derive the ITER operational space, where ELM mitigation to avoid melting of the W divertor monoblocks top surface is not required and appropriate control of W sources and radiation in the main plasma can be ensured through ELM control by pellet pacing. We apply the experimental scaling that relates the maximum ELM energy density deposited at the divertor with the pedestal parameters and this eliminates the uncertainty related with the ELM wetted area for energy deposition at the divertor and enables the definition of the ITER operating space through global plasma parameters. Our evaluation is thus based on this empirical scaling for ELM power loads together with the scaling for the pedestal pressure limit based on predictions from stability codes. In particular, our analysis has revealed that for the pedestal pressure predicted by the EPED1  +  SOLPS scaling, ELM mitigation to avoid melting of the W divertor monoblocks top surface may not be required for 2.65 T H-modes with normalized pedestal densities (to the Greenwald limit) larger than 0.5 to a level of current of 6.5–7.5 MA, which depends on assumptions on the divertor power flux during ELMs and between ELMs that expand the range of experimental uncertainties. The pellet and gas fuelling requirements compatible with control of plasma detachment, core plasma tungsten accumulation and H-mode operation (including post-ELM W transient radiation) have been assessed by 1.5D transport simulations for a range of assumptions regarding W re-deposition at the divertor including the most conservative assumption of zero prompt re-deposition. With such conservative assumptions, the post-ELM W transient radiation imposes a very stringent limit on ELM energy losses and the associated minimum required ELM frequency. Depending on W transport assumptions during the ELM, a maximum ELM frequency is also identified above which core tungsten accumulation takes place.

  7. Ulmus crassifolia Nutt. Cedar Elm

    Treesearch

    John J. Stransky; Sylvia M. Bierschenk

    1990-01-01

    Cedar elm (Ulmus cassifolia) grows rapidly to medium or large size in the Southern United States and northeastern Mexico, where it may sometimes be called basket elm, red elm, southern rock elm, or olmo (Spanish) It usually is found on moist, limestone soils along water courses with other bottomland trees, but it also paws on dry limestone hills. The...

  8. Elm yellows: a widespread and overlooked killer of elm trees across the United States

    Treesearch

    Charles E. Flower; Nancy Hayes-Plazolles; Cristina Rosa; James M. Slavicek

    2017-01-01

    The elm yellows phytoplasma (Candidatus Phytoplasma ulmi) is a geographically widespread pathogen that poses a significant threat to most native wild elms in North America (Ulmus americana, U. rubra, U. alata, U. crassifolia, and U. serotina) (Mäurer et al. 1993), as well as to the success of American elm...

  9. Do mites phoretic on elm bark beetles contribute to the transmission of Dutch elm disease?

    Treesearch

    John Moser; Heino Konrad; Stacy Blomquist; Thomas Kirisits

    2010-01-01

    Dutch elm disease (DED) is a destructive vascular wilt disease of elm (Ulmus) trees caused by the introduced Ascomycete fungus Ophiostoma novo-ulmi. In Europe, this DED pathogen is transmitted by elm bark beetles in the genus Scolytus. These insects carry phoretic mites to new, suitable habitats. The aim of this...

  10. Diversifying natural resources value measurements: The Trinity River study

    USGS Publications Warehouse

    Taylor, J.G.; Douglas, A.J.

    1999-01-01

    An interdisciplinary team set out to establish the economic and social values of the Trinity River in northern California. This information was intended to support the Secretary of the Interior's decision on allocation of Trinity River flows. This team set out to measure the values of Trinity River flows, fishery resources, and recreation amenities in several different ways. A survey was mailed to users of the Trinity River. This single instrument included economic measures (willingness-to-pay and costs incurred in visiting) and social-psychological measures (importance, satisfaction, and water allocation preferences). A closely related survey measured several of these same values among west coast regional households. The results of these surveys were compiled, and the measured economic and social values were compared. We found that integrating economic and social value information provides a greater depth of understanding of the resource's value. In addition, this integration provides a more in-depth understanding through the quantitative and qualitative results that emerge.

  11. Edge localized mode rotation and the nonlinear dynamics of filaments

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Morales, J. A.; Bécoulet, M.; Garbet, X.

    2016-04-15

    Edge Localized Modes (ELMs) rotating precursors were reported few milliseconds before an ELM crash in several tokamak experiments. Also, the reversal of the filaments rotation at the ELM crash is commonly observed. In this article, we present a mathematical model that reproduces the rotation of the ELM precursors as well as the reversal of the filaments rotation at the ELM crash. Linear ballooning theory is used to establish a formula estimating the rotation velocity of ELM precursors. The linear study together with nonlinear magnetohydrodynamic simulations give an explanation to the rotations observed experimentally. Unstable ballooning modes, localized at the pedestal,more » grow and rotate in the electron diamagnetic direction in the laboratory reference frame. Approaching the ELM crash, this rotation decreases corresponding to the moment when the magnetic reconnection occurs. During the highly nonlinear ELM crash, the ELM filaments are cut from the main plasma due to the strong sheared mean flow that is nonlinearly generated via the Maxwell stress tensor.« less

  12. 75 FR 38143 - Investigations Regarding Certifications of Eligibility To Apply for Worker Adjustment Assistance

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-01

    ........... 06/01/10 05/26/10 America (Workers). 74165 Trinity Tank Car Plant Longview, TX 06/01/10 05/26/10 1194 (State/One- Stop). 74166 Trinity Tank Car Plant Longview, TX 06/01/10 05/26/10 1110 (State/One- Stop). 74167 Trinity Tank Car Plant Longview, TX 06/01/10 05/26/10 17 (State/One- Stop). 74168 Kokomo Sanitary...

  13. Geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers within northern Bexar and Comal Counties, Texas

    USGS Publications Warehouse

    Clark, Allan K.; Golab, James A.; Morris, Robert R.

    2016-11-28

    During 2014–16, the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, documented the geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers within northern Bexar and Comal Counties, Texas. The Edwards and Trinity aquifers are major sources of water for agriculture, industry, and urban and rural communities in south-central Texas. Both the Edwards and Trinity are classified as major aquifers by the State of Texas.The purpose of this report is to present the geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers within northern Bexar and Comal Counties, Tex. The report includes a detailed 1:24,000-scale hydrostratigraphic map, names, and descriptions of the geology and hydrostratigraphic units (HSUs) in the study area.The scope of the report is focused on geologic framework and hydrostratigraphy of the outcrops and hydrostratigraphy of the Edwards and Trinity aquifers within northern Bexar and Comal Counties, Tex. In addition, parts of the adjacent upper confining unit to the Edwards aquifer are included.The study area, approximately 866 square miles, is within the outcrops of the Edwards and Trinity aquifers and overlying confining units (Washita, Eagle Ford, Austin, and Taylor Groups) in northern Bexar and Comal Counties, Tex. The rocks within the study area are sedimentary and range in age from Early to Late Cretaceous. The Miocene-age Balcones fault zone is the primary structural feature within the study area. The fault zone is an extensional system of faults that generally trends southwest to northeast in south-central Texas. The faults have normal throw, are en echelon, and are mostly downthrown to the southeast.The Early Cretaceous Edwards Group rocks were deposited in an open marine to supratidal flats environment during two marine transgressions. The Edwards Group is composed of the Kainer and Person Formations. Following tectonic uplift, subaerial exposure, and erosion near the end of Early Cretaceous time, the area of present-day south-central Texas was again submerged during the Late Cretaceous by a marine transgression resulting in deposition of the Georgetown Formation of the Washita Group.The Early Cretaceous Edwards Group, which overlies the Trinity Group, is composed of mudstone to boundstone, dolomitic limestone, argillaceous limestone, evaporite, shale, and chert. The Kainer Formation is subdivided into (bottom to top) the basal nodular, dolomitic, Kirschberg Evaporite, and grainstone members. The Person Formation is subdivided into (bottom to top) the regional dense, leached and collapsed (undivided), and cyclic and marine (undivided) members.Hydrostratigraphically the rocks exposed in the study area represent a section of the upper confining unit to the Edwards aquifer, the Edwards aquifer, the upper zone of the Trinity aquifer, and the middle zone of the Trinity aquifer. The Pecan Gap Formation (Taylor Group), Austin Group, Eagle Ford Group, Buda Limestone, and Del Rio Clay are generally considered to be the upper confining unit to the Edwards aquifer.The Edwards aquifer was subdivided into HSUs I to VIII. The Georgetown Formation of the Washita Group contains HSU I. The Person Formation of the Edwards Group contains HSUs II (cyclic and marine members [Kpcm], undivided), III (leached and collapsed members [Kplc,] undivided), and IV (regional dense member [Kprd]), and the Kainer Formation of the Edwards Group contains HSUs V (grainstone member [Kkg]), VI (Kirschberg Evaporite Member [Kkke]), VII (dolomitic member [Kkd]), and VIII (basal nodular member [Kkbn]).The Trinity aquifer is separated into upper, middle, and lower aquifer units (hereinafter referred to as “zones”). The upper zone of the Trinity aquifer is in the upper member of the Glen Rose Limestone. The middle zone of the Trinity aquifer is formed in the lower member of the Glen Rose Limestone, Hensell Sand, and Cow Creek Limestone. The regionally extensive Hammett Shale forms a confining unit between the middle and lower zones of the Trinity aquifer. The lower zone of the Trinity aquifer consists of the Sligo and Hosston Formations, which do not crop out in the study area.The upper zone of the Trinity aquifer is subdivided into five informal HSUs (top to bottom): cavernous, Camp Bullis, upper evaporite, fossiliferous, and lower evaporite. The middle zone of the Trinity aquifer is composed of the (top to bottom) Bulverde, Little Blanco, Twin Sisters, Doeppenschmidt, Rust, Honey Creek, Hensell, and Cow Creek HSUs. The underlying Hammett HSU is a regional confining unit between the middle and lower zones of the Trinity aquifer. The lower zone of the Trinity aquifer is not exposed in the study area.Groundwater recharge and flow paths in the study area are influenced not only by the hydrostratigraphic characteristics of the individual HSUs but also by faults and fractures and geologic structure. Faulting associated with the Balcones fault zone (1) might affect groundwater flow paths by forming a barrier to flow that results in water moving parallel to the fault plane, (2) might affect groundwater flow paths by increasing flow across the fault because of fracturing and juxtaposing porous and permeable units, or (3) might have no effect on the groundwater flow paths.The hydrologic connection between the Edwards and Trinity aquifers and the various HSUs is complex. The complexity of the aquifer system is a combination of the original depositional history, bioturbation, primary and secondary porosity, diagenesis, and fracturing of the area from faulting. All of these factors have resulted in development of modified porosity, permeability, and transmissivity within and between the aquifers. Faulting produced highly fractured areas that have allowed for rapid infiltration of water and subsequently formed solutionally enhanced fractures, bedding planes, channels, and caves that are highly permeable and transmissive. The juxtaposition resulting from faulting has resulted in areas of interconnectedness between the Edwards and Trinity aquifers and the various HSUs that form the aquifers.

  14. Elm diseases

    Treesearch

    John W. Peacock

    1989-01-01

    Dutch elm disease was found in Cleveland, Ohio, in 1930, and is now in most of the contiguous 48 states. The disease is caused by a fungus that has killed millions of wild and planted elms. Losses have been the greatest in the eastern United States. The fungus attacks all elms, but our native species, American, slippery, and rock elm have little or no resistance to the...

  15. HOW to Identify and Manage Dutch Elm Disease

    Treesearch

    Linda Haugen

    1998-01-01

    At one time, the American elm was considered to be an ideal street tree because it was graceful, long-lived, fast growing, and tolerant of compacted soils and air pollution. Then Dutch elm disease (DED) was introduced and began devastating the elm population. Estimates of DED losses of elm in communities and woodlands across the U.S. are staggering (figure 1). Because...

  16. Elms and Dutch elm disease: a quick overview

    Treesearch

    Michael Marcotrigiano

    2017-01-01

    In the 1930s Dutch elm disease (DED) was accidentally introduced from Europe into the United States. It had a devastating impact on American elm (Ulmus americana) and its relatives in urban and riparian environments. In the United States, the three-part pathosystem for DED is unique in that the affected elm species are North American, the pathogen originated in Asia,...

  17. Hybridization and introgression between the exotic Siberian elm, Ulmus pumila, and the native Field elm, U. minor, in Italy

    USDA-ARS?s Scientific Manuscript database

    In response to the first Dutch elm disease (DED) pandemic, Siberian elm, Ulmus pumila, was planted to replace the native elm, U. minor, in Italy. The potential for hybridization between these two species is high and repeated hybridization could result in the genetic swamping of the native species an...

  18. Dutch Elm Disease (DED) and the American Elm (Pest Alert)

    Treesearch

    USDA Forest Service

    1999-01-01

    For decades the American elm was one of our most treasured trees, gracing streets and parks of many cities with beautiful form and dense foliage. The American elm was particularly well suited to urban sites because it grows quickly, is long-lived, and is tolerant of compacted soils and air pollution. However, in most communities Dutch elm disease (DED) killed a...

  19. Water-quality assessment of the Trinity River Basin, Texas - Nutrients in two coastal prairie streams draining agricultural areas, 1994-95

    USGS Publications Warehouse

    Land, Larry F.

    1996-01-01

    In 1991, the U.S. Geological Survey (USGS) began nationwide implementation of the National Water-Quality Assessment (NAWQA) Program. Long-term goals of NAWQA are to describe the status of and trends in the quality of a large, representative part of the Nation?s surface- and ground-water resources and to provide a sound, scientific understanding of the primary natural and human factors affecting the quality of these resources (Leahy and others, 1990). The Trinity River Basin in east-central Texas (fig. 1) was among the first 20 hydrologic areas, called study units, to be assessed by this program. The first intensive data-collection phase for the Trinity River Basin NAWQA began in March 1993 and ended in September 1995. Streams in the Trinity River Basin were assessed by sampling water, bed sediment, and tissue of biota and characterizing the aquatic communities and their habitat. Aquifers were assessed by sampling water from wells. The coastal prairie is a small part of the Trinity River Basin, but it is environmentally important because of its proximity to Galveston Bay and the extensive use of agricultural chemicals on many irrigated farms. Galveston Bay (fig. 1) was selected by Congress as an estuary of national significance and was included on a priority list for the National Estuary Program. The Trinity River is especially important because its watershed dominates the total Galveston Bay drainage area and because its flow contributes substantial amounts of freshwater and water-quality constituents to the bay. Historically, measurements of the quantity and quality of water entering Galveston Bay from the Trinity River Basin have been made using data from a station about 113 kilometers (70 miles) upstream from Trinity Bay, an inlet bay to Galveston Bay. With a focused objective of providing additional water-quality information in the intervening coastal prairie area and an overall objective of improving the understanding of the relations between farming practices and stream quality in the Trinity River Basin, a special study was conducted. This report provides a description of the occurrence and concentrations of nutrients in two streams in this intervening area. An earlier report by Brown (1996) describes the occurrence and concentrations of pesticides in these two streams. An overall analysis of nutrient data collected during 1974?91 in the Trinity River Basin is given by Van Metre and Reutter (1995).

  20. Improving Classification Performance through an Advanced Ensemble Based Heterogeneous Extreme Learning Machines.

    PubMed

    Abuassba, Adnan O M; Zhang, Dezheng; Luo, Xiong; Shaheryar, Ahmad; Ali, Hazrat

    2017-01-01

    Extreme Learning Machine (ELM) is a fast-learning algorithm for a single-hidden layer feedforward neural network (SLFN). It often has good generalization performance. However, there are chances that it might overfit the training data due to having more hidden nodes than needed. To address the generalization performance, we use a heterogeneous ensemble approach. We propose an Advanced ELM Ensemble (AELME) for classification, which includes Regularized-ELM, L 2 -norm-optimized ELM (ELML2), and Kernel-ELM. The ensemble is constructed by training a randomly chosen ELM classifier on a subset of training data selected through random resampling. The proposed AELM-Ensemble is evolved by employing an objective function of increasing diversity and accuracy among the final ensemble. Finally, the class label of unseen data is predicted using majority vote approach. Splitting the training data into subsets and incorporation of heterogeneous ELM classifiers result in higher prediction accuracy, better generalization, and a lower number of base classifiers, as compared to other models (Adaboost, Bagging, Dynamic ELM ensemble, data splitting ELM ensemble, and ELM ensemble). The validity of AELME is confirmed through classification on several real-world benchmark datasets.

  1. Improving Classification Performance through an Advanced Ensemble Based Heterogeneous Extreme Learning Machines

    PubMed Central

    Abuassba, Adnan O. M.; Ali, Hazrat

    2017-01-01

    Extreme Learning Machine (ELM) is a fast-learning algorithm for a single-hidden layer feedforward neural network (SLFN). It often has good generalization performance. However, there are chances that it might overfit the training data due to having more hidden nodes than needed. To address the generalization performance, we use a heterogeneous ensemble approach. We propose an Advanced ELM Ensemble (AELME) for classification, which includes Regularized-ELM, L2-norm-optimized ELM (ELML2), and Kernel-ELM. The ensemble is constructed by training a randomly chosen ELM classifier on a subset of training data selected through random resampling. The proposed AELM-Ensemble is evolved by employing an objective function of increasing diversity and accuracy among the final ensemble. Finally, the class label of unseen data is predicted using majority vote approach. Splitting the training data into subsets and incorporation of heterogeneous ELM classifiers result in higher prediction accuracy, better generalization, and a lower number of base classifiers, as compared to other models (Adaboost, Bagging, Dynamic ELM ensemble, data splitting ELM ensemble, and ELM ensemble). The validity of AELME is confirmed through classification on several real-world benchmark datasets. PMID:28546808

  2. Control of edge localized modes by pedestal deposited impurity in the HL-2A tokamak

    NASA Astrophysics Data System (ADS)

    Zhang, Y. P.; Mazon, D.; Zou, X. L.; Zhong, W. L.; Gao, J. M.; Zhang, K.; Sun, P.; Dong, C. F.; Cui, Z. Y.; Liu, Yi; Shi, Z. B.; Yu, D. L.; Cheng, J.; Jiang, M.; Xu, J. Q.; Isobe, M.; Xiao, G. L.; Chen, W.; Song, S. D.; Bai, X. Y.; Zhang, P. F.; Yuan, G. L.; Ji, X. Q.; Li, Y. G.; Zhou, Y.; Delpech, L.; Ekedahl, A.; Giruzzi, G.; Hoang, T.; Peysson, Y.; Song, X. M.; Song, X. Y.; Li, X.; Ding, X. T.; Dong, J. Q.; Yang, Q. W.; Xu, M.; Duan, X. R.; Liu, Y.; the HL-2A Team

    2018-04-01

    Effect of the pedestal deposited impurity on the edge-localized mode (ELM) behaviour has been observed and intensively investigated in the HL-2A tokamak. Impurities have been externally seeded by a newly developed laser blow-off (LBO) system. Both mitigation and suppression of ELMs have been realized by LBO-seeded impurity. Measurements have shown that the LBO-seeded impurity particles are mainly deposited in the pedestal region. During the ELM mitigation phase, the pedestal density fluctuation is significantly increased, indicating that the ELM mitigation may be achieved by the enhancement of the pedestal transport. The transition from ELM mitigation to ELM suppression was triggered when the number of the LBO-seeded impurity exceeds a threshold value. During the ELM suppression phase, a harmonic coherent mode (HCM) is excited by the LBO-seeded impurity, and the pedestal density fluctuation is significantly decreased, the electron density is continuously increased, implying that HCM may reduce the pedestal turbulence, suppress ELMs, increase the pedestal pressure, thus extending the Peeling-Ballooning instability limit. It has been found that the occurance of the ELM mitigation and ELM suppression closely depends on the LBO laser spot diameter.

  3. ELM mitigation studies in JET and implications for ITER

    NASA Astrophysics Data System (ADS)

    de La Luna, Elena

    2009-11-01

    Type I edge localized modes (ELMs) remain a serious concern for ITER because of the high transient heat and particle flux that can lead to rapid erosion of the divertor plates. This has stimulated worldwide research on exploration of different methods to avoid or at least mitigate the ELM energy loss while maintaining adequate confinement. ITER will require reliable ELM control over a wide range of operating conditions, including changes in the edge safety factor, therefore a suite of different techniques is highly desirable. In JET several techniques have been demonstrated for control the frequency and size of type I ELMs, including resonant perturbations of the edge magnetic field (RMP), ELM magnetic triggering by fast vertical movement of the plasma column (``vertical kicks'') and ELM pacing using pellet injection. In this paper we present results from recent dedicated experiments in JET focusing on integrating the different ELM mitigation methods into similar plasma scenarios. Plasma parameter scans provide comparison of the performance of the different techniques in terms of both the reduction in ELM size and on the impact of each control method on plasma confinement. The compatibility of different ELM mitigation schemes has also been investigated. The plasma response to RMP and vertical kicks during the ELM mitigation phase shares common features: the reduction in ELM size (up to a factor of 3) is accompanied by a reduction in pedestal pressure (mainly due to a loss of density) with only minor (< 10%) reduction of the stored energy. Interestingly, it has been found that the combined application of RMP and kicks leads to a reduction of the threshold perturbation level (vertical displacement in the case of the kicks) necessary for the ELM mitigation to occur. The implication of these results for ITER will be discussed.

  4. Adaptive control of nonlinear system using online error minimum neural networks.

    PubMed

    Jia, Chao; Li, Xiaoli; Wang, Kang; Ding, Dawei

    2016-11-01

    In this paper, a new learning algorithm named OEM-ELM (Online Error Minimized-ELM) is proposed based on ELM (Extreme Learning Machine) neural network algorithm and the spreading of its main structure. The core idea of this OEM-ELM algorithm is: online learning, evaluation of network performance, and increasing of the number of hidden nodes. It combines the advantages of OS-ELM and EM-ELM, which can improve the capability of identification and avoid the redundancy of networks. The adaptive control based on the proposed algorithm OEM-ELM is set up which has stronger adaptive capability to the change of environment. The adaptive control of chemical process Continuous Stirred Tank Reactor (CSTR) is also given for application. The simulation results show that the proposed algorithm with respect to the traditional ELM algorithm can avoid network redundancy and improve the control performance greatly. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

  5. Genotype x environment interaction and growth stability of several elm clones resistant to Dutch elm disease

    Treesearch

    Alberto Santini; Francesco Pecori; Alessia L. Pepori; Luisa Ghelardini

    2012-01-01

    The elm breeding program carried out in Italy at the Institute of Plant Protection - Consiglio Nazionale delle Ricercje (CNR) during the last 40 years aimed to develop Dutch elm disease (DED)-resistant elm selections specific to the Mediterranean environment. The need for genotypes adapted to Mediterranean conditions was evident from the poor performance of the Dutch...

  6. Novel insights into the elm yellows phytoplasma genome and into the metagenome of elm yellows-infected elms

    Treesearch

    Christina Rosa; Paolo Margaria; Scott M. Geib; Erin D. Scully

    2017-01-01

    In North America, American elms were historically present throughout the northeastern United States and southeastern Canada. The longevity of these trees, their resistance to the harsh urban environment, and their aesthetics led to their wide use in landscaping and streetscaping over several decades. American elms were one of most cultivated plants in the United States...

  7. Building a database for statistical characterization of ELMs on DIII-D

    NASA Astrophysics Data System (ADS)

    Fritch, B. J.; Marinoni, A.; Bortolon, A.

    2017-10-01

    Edge localized modes (ELMs) are bursty instabilities which occur in the edge region of H-mode plasmas and have the potential to damage in-vessel components of future fusion machines by exposing the divertor region to large energy and particle fluxes during each ELM event. While most ELM studies focus on average quantities (e.g. energy loss per ELM), this work investigates the statistical distributions of ELM characteristics, as a function of plasma parameters. A semi-automatic algorithm is being used to create a database documenting trigger times of the tens of thousands of ELMs for DIII-D discharges in scenarios relevant to ITER, thus allowing statistically significant analysis. Probability distributions of inter-ELM periods and energy losses will be determined and related to relevant plasma parameters such as density, stored energy, and current in order to constrain models and improve estimates of the expected inter-ELM periods and sizes, both of which must be controlled in future reactors. Work supported in part by US DoE under the Science Undergraduate Laboratory Internships (SULI) program, DE-FC02-04ER54698 and DE-FG02- 94ER54235.

  8. Recovery of copper and cyanide from waste cyanide solutions using emulsion liquid membrane with LIX 7950 as the carrier.

    PubMed

    Xie, Feng; Wang, Wei

    2017-08-01

    The feasibility of using emulsion liquid membranes (ELMs) with the guanidine extractant LIX 7950 as the mobile carrier for detoxifying copper-containing waste cyanide solutions has been determined. Relatively stable ELMs can be maintained under suitable stirring speed during mixing ELMs and the external solution. Effective extraction of copper cyanides by ELMs only occurs at pH below 11. High copper concentration in the external phase and high volume ratio of the external phase to ELMs result in high transport rates of copper and cyanide. High molar ratio of cyanide to copper tends to suppress copper extraction. The presence of thiocyanate ion significantly depresses the transport of copper and cyanide through the membrane while the thiosulfate ion produces less impact on copper removal by ELMs. Zinc and nickel cyanides can also be effectively extracted by ELMs. More than 90% copper and cyanide can be effectively removed from alkaline cyanide solutions by ELMs under suitable experimental conditions, indicating the effectiveness of using the designed ELM for recovering copper and cyanide from waste cyanide solutions.

  9. Water-quality assessment of the Trinity River basin, Texas : ground-water quality of the Trinity, Carrizo-Wilcox, and Gulf Coast aquifers, February-August 1994

    USGS Publications Warehouse

    Reutter, David C.; Dunn, David D.

    2000-01-01

    Ground-water samples were collected from wells in the outcrops of the Trinity, Carrizo-Wilcox, and Gulf Coast aquifers during February-August 1994 to determine the quality of ground water in the three major aquifers in the Trinity River Basin study unit, Texas. These samples were collected and analyzed for selected properties, nutrients, major inorganic constituents, trace elements, pesticides, dissolved organic carbon, total phenols, methylene blue active substances, and volatile organic compounds as part of the U.S. Geological Survey National Water-Quality Assessment Program. Quality-control practices included the collection and analysis of blank, duplicate, and spiked samples. Samples were collected from 12 shallow wells (150 feet or less) and from 12 deep wells (greater than 150 feet) in the Trinity aquifer, 11 shallow wells and 12 deep wells in the Carrizo-Wilcox aquifer, and 14 shallow wells and 10 deep wells in the Gulf Coast aquifer. The three aquifers had similar water chemistries-calcium was the dominant cation and bicarbonate the dominant anion. Statistical tests relating well depths to concentrations of nutrients and major inorganic constituents indicated correlations between well depth and concentrations of ammonia nitrogen, nitrite plus nitrate nitrogen, bicarbonate, sodium, and dissolved solids in the Carrizo-Wilcox aquifer and between well depth and concentrations of sulfate in the Gulf Coast aquifer. The tests indicated no significant correlations for the Trinity aquifer. Concentrations of dissolved solids were larger than the secondary maximum contaminant level of 500 milligrams per liter established for drinking water by the U.S. Environmental Protection Agency in 12 wells in the Trinity aquifer, 4 wells in the Carrizo-Wilcox aquifer, and 6 wells in the Gulf Coast aquifer. Iron concentrations were larger than the secondary maximum contaminant level of 300 micrograms per liter in at least 3 samples from each aquifer, and manganese concentrations were larger than the secondary maximum contaminant level of 50 micrograms per liter in at least 2 samples from each aquifer. The pesticides atrazine, deethylatrazine, and pp'-DDE were detected in at least one sample from each aquifer. Diazinon was detected in 11 Trinity aquifer samples and 4 Carrizo-Wilcox aquifer samples. Each aquifer had one detection of a volatile organic compound-benzene in the Trinity aquifer, trichlorofluoromethane in the Carrizo-Wilcox aquifer, and trichloromethane in the Gulf Coast aquifer.

  10. Development of new Dutch Elm disease-tolerant selections for restoration of the American Elm in urban and forested landscapes

    Treesearch

    C.C. Pinchot; C.E. Flower; K.S. Knight; C. Marks; R. Minocha; D. Lesser; K. Woeste; P.G. Schaberg; B. Baldwin; D.M. Delatte; T.D. Fox; N. Hayes-Plazolles; B. Held; K. Lehtoma; S. Long; S. Mattix; A. Sipes; J.M. Slavicek

    2017-01-01

    The goal of our research and development efforts is to restore American elm (Ulmus americana) as a species in both natural and urban landscapes. Accomplishing this goal requires identification/generation of additional American elm cultivars that are tolerant to Dutch elm disease (DED) caused by Ophiostoma ulmi and O. novo-ulmi, and development of methods to reintroduce...

  11. Relative importance of root grafts and bark beetles to the spread of Dutch elm disease

    Treesearch

    R. A. Cuthbert; W. N., Jr. Cannon; J. W. Peacock

    1975-01-01

    Root-graft transmission of Dutch elm disease (DED) is sometimes ignored in both research studies and city programs to control DED. Our results indicate that elms adjacent to 1-, 2-, or 3-year-old stumps have a disease rate three to five times higher than elms not adjacent to stumps. We conclude that in Detroit, which has elm plantings typical of many United States...

  12. Adaptive Online Sequential ELM for Concept Drift Tackling

    PubMed Central

    Basaruddin, Chan

    2016-01-01

    A machine learning method needs to adapt to over time changes in the environment. Such changes are known as concept drift. In this paper, we propose concept drift tackling method as an enhancement of Online Sequential Extreme Learning Machine (OS-ELM) and Constructive Enhancement OS-ELM (CEOS-ELM) by adding adaptive capability for classification and regression problem. The scheme is named as adaptive OS-ELM (AOS-ELM). It is a single classifier scheme that works well to handle real drift, virtual drift, and hybrid drift. The AOS-ELM also works well for sudden drift and recurrent context change type. The scheme is a simple unified method implemented in simple lines of code. We evaluated AOS-ELM on regression and classification problem by using concept drift public data set (SEA and STAGGER) and other public data sets such as MNIST, USPS, and IDS. Experiments show that our method gives higher kappa value compared to the multiclassifier ELM ensemble. Even though AOS-ELM in practice does not need hidden nodes increase, we address some issues related to the increasing of the hidden nodes such as error condition and rank values. We propose taking the rank of the pseudoinverse matrix as an indicator parameter to detect “underfitting” condition. PMID:27594879

  13. Summary of Migration and Survival Data from Radio-Tagged Juvenile Coho Salmon in the Trinity River, Northern California, 2008

    USGS Publications Warehouse

    Beeman, John W.; Hansel, Hal; Juhnke, Steve; Stutzer, Greg

    2009-01-01

    The survival of hatchery-origin juvenile coho salmon from the Trinity River Hatchery was estimated as they migrated seaward through the Trinity and Klamath Rivers. The purpose of the study was to collect data for comparison to a similar study in the Klamath River and provide data to the Trinity River Restoration Program. A total of 200 fish fitted with radio transmitters were released into the Trinity River near the hatchery (river kilometer 252 from the mouth of the Klamath River) biweekly from March 19 to May 28, 2008. Fish from the earliest release groups took longer to pass the first detection site 10 kilometers downstream of the hatchery than fish from the later release groups, but travel times between subsequent sites were often similar among the release groups. The travel times of individuals through the 239 kilometer study area ranged from 15.5 to 84.6 days with a median of 43.3 days. The data and models did not support differences in survival among release groups, but did support differences among river reaches. The probability of survival in the first 53 kilometers was lower than in the reaches farther downstream, which is similar to trends in juvenile coho salmon in the Klamath River. The lowest estimated survival in this study was in the first 10 kilometers from release in the Trinity River (0.676 SE 0.036) and the highest estimated survival was in the final 20 kilometer reach in the Klamath River (0.987 SE 0.013). Estimated survivals of radio-tagged juvenile coho salmon from release to Klamath River kilometer 33 were 0.639 per 100 kilometers for Trinity River fish and 0.721 per 100 kilometers for Klamath River fish.

  14. Performance of VPIC on Trinity

    NASA Astrophysics Data System (ADS)

    Nystrom, W. D.; Bergen, B.; Bird, R. F.; Bowers, K. J.; Daughton, W. S.; Guo, F.; Li, H.; Nam, H. A.; Pang, X.; Rust, W. N., III; Wohlbier, J.; Yin, L.; Albright, B. J.

    2016-10-01

    Trinity is a new major DOE computing resource which is going through final acceptance testing at Los Alamos National Laboratory. Trinity has several new and unique architectural features including two compute partitions, one with dual socket Intel Haswell Xeon compute nodes and one with Intel Knights Landing (KNL) Xeon Phi compute nodes. Additional unique features include use of on package high bandwidth memory (HBM) for the KNL nodes, the ability to configure the KNL nodes with respect to HBM model and on die network topology in a variety of operational modes at run time, and use of solid state storage via burst buffer technology to reduce time required to perform I/O. An effort is in progress to port and optimize VPIC to Trinity and evaluate its performance. Because VPIC was recently released as Open Source, it is being used as part of acceptance testing for Trinity and is participating in the Trinity Open Science Program which has resulted in excellent collaboration activities with both Cray and Intel. Results of this work will be presented on performance of VPIC on both Haswell and KNL partitions for both single node runs and runs at scale. Work performed under the auspices of the U.S. Dept. of Energy by the Los Alamos National Security, LLC Los Alamos National Laboratory under contract DE-AC52-06NA25396 and supported by the LANL LDRD program.

  15. FY17 CSSE L2 Milestone Report: Analyzing Power Usage Characteristics of Workloads Running on Trinity.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Pedretti, Kevin

    This report summarizes the work performed as part of a FY17 CSSE L2 milestone to in- vestigate the power usage behavior of ASC workloads running on the ATS-1 Trinity plat- form. Techniques were developed to instrument application code regions of interest using the Power API together with the Kokkos profiling interface and Caliper annotation library. Experiments were performed to understand the power usage behavior of mini-applications and the SNL/ATDM SPARC application running on ATS-1 Trinity Haswell and Knights Landing compute nodes. A taxonomy of power measurement approaches was identified and presented, providing a guide for application developers to follow. Controlledmore » scaling study experiments were performed on up to 2048 nodes of Trinity along with smaller scale ex- periments on Trinity testbed systems. Additionally, power and energy system monitoring information from Trinity was collected and archived for post analysis of "in-the-wild" work- loads. Results were analyzed to assess the sensitivity of the workloads to ATS-1 compute node type (Haswell vs. Knights Landing), CPU frequency control, node-level power capping control, OpenMP configuration, Knights Landing on-package memory configuration, and algorithm/solver configuration. Overall, this milestone lays groundwork for addressing the long-term goal of determining how to best use and operate future ASC platforms to achieve the greatest benefit subject to a constrained power budget.« less

  16. QUANTITATIVE TESTS OF ELMS AS INTERMEDIATE N PEELING-BALOONING MODES

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    LAO,LL; SNYDER,PB; LEONARD,AW

    2003-03-01

    A271 QUANTITATIVE TESTS OF ELMS AS INTERMEDIATE N PEELING-BALOONING MODES. Several testable features of the working model of edge localized modes (ELMs) as intermediate toroidal mode number peeling-ballooning modes are evaluated quantitatively using DIII-D and JT-60U experimental data and the ELITE MHD stability code. These include the hypothesis that ELM sizes are related to the radial widths of the unstable MHD modes, the unstable modes have a strong ballooning character localized in the outboard bad curvature region, and ELM size generally becomes smaller at high edge collisionality. ELMs are triggered when the growth rates of the unstable MHD modes becomemore » significantly large. These testable features are consistent with many ELM observations in DIII-D and JT-60U discharges.« less

  17. Is extreme learning machine feasible? A theoretical assessment (part II).

    PubMed

    Lin, Shaobo; Liu, Xia; Fang, Jian; Xu, Zongben

    2015-01-01

    An extreme learning machine (ELM) can be regarded as a two-stage feed-forward neural network (FNN) learning system that randomly assigns the connections with and within hidden neurons in the first stage and tunes the connections with output neurons in the second stage. Therefore, ELM training is essentially a linear learning problem, which significantly reduces the computational burden. Numerous applications show that such a computation burden reduction does not degrade the generalization capability. It has, however, been open that whether this is true in theory. The aim of this paper is to study the theoretical feasibility of ELM by analyzing the pros and cons of ELM. In the previous part of this topic, we pointed out that via appropriately selected activation functions, ELM does not degrade the generalization capability in the sense of expectation. In this paper, we launch the study in a different direction and show that the randomness of ELM also leads to certain negative consequences. On one hand, we find that the randomness causes an additional uncertainty problem of ELM, both in approximation and learning. On the other hand, we theoretically justify that there also exist activation functions such that the corresponding ELM degrades the generalization capability. In particular, we prove that the generalization capability of ELM with Gaussian kernel is essentially worse than that of FNN with Gaussian kernel. To facilitate the use of ELM, we also provide a remedy to such a degradation. We find that the well-developed coefficient regularization technique can essentially improve the generalization capability. The obtained results reveal the essential characteristic of ELM in a certain sense and give theoretical guidance concerning how to use ELM.

  18. Broadening of the divertor heat flux footprint with increasing number of ELM filaments in NSTX

    NASA Astrophysics Data System (ADS)

    Ahn, Joon-Wook

    2014-10-01

    We report on the broadening (narrowing) of the ELM heat flux footprint with increasing (decreasing) number of filamentary striations from in-depth thermography measurements in NSTX. Edge localized modes (ELMs) represent a challenge to future fusion devices, due to the high heat fluxes on plasma facing surfaces. One ameliorating factor has been that the divertor heat flux characteristic profile width (λq) has been observed to broaden with the size of ELM, as compared with the inter-ELM λq, which keeps the peak heat flux (qpeak) from increasing. In contrast, λq has been observed to narrow during ELMs under certain conditions in NSTX, for both naturally occurring and 3-D fields triggered ELMs. Fast thermographic measurements and detailed analysis demonstrate that the ELM λq increases with the number of observed filamentary striations, i . e . , profile narrowing (broadening) occurs when the number of striations is smaller (larger) than 3-4. With profile narrowing, qpeak at ELM peak times is inversely related (proportional) to λq (the ELM size), exacerbating the heat flux problem. Edge stability analysis shows that NSTX ELMs almost always lie on the current-driven kink/peeling mode side with low toroidal mode number (n = 1--5), consistent with the typical numbers of striations in NSTX (0-8) in comparison 10--15 striations are normally observed in intermediate-n peeling-ballooning ELMs, e.g., from JET. The NSTX characteristics may translate directly to ITER, which is also projected to lie on the low-n kink/peeling stability boundary. This work was supported by the U.S. DOE, Contract DE-AC05-00OR22725 (ORNL) and DE-AC02-09CH11466 (PPPL).

  19. 1. EXTERIOR VIEW OF ELM CITY PLANT (A. FRANCIS WALKER, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. EXTERIOR VIEW OF ELM CITY PLANT (A. FRANCIS WALKER, 1905-07) FROM SECOND AVENUE ON OPPOSITE SIDE OF ENTRANCE. THIS STRUCTURE WAS ORIGINALLY BUILT AS THE ELM CITY COTTON MILL OF CALLAWAY MILLS. NOTE RESERVOIR IN FOREGROUND. THIS PHOTOGRAPH IS THE LEFT SIDE OF A PANORAMA VIEW THAT INCLUDES HAER Nos. GA-128-2 AND GA-128-3. - Elm City Cotton Mill, 1000 Elm Street, La Grange, Troup County, GA

  20. KSC-08pd3751

    NASA Image and Video Library

    2008-11-19

    CAPE CANAVERAL, Fla. – In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, workers check the mast deployment on the SEDA-AP or Space Environment Data Acquisition equipment--Attached Payload. SEDA-AP will measure space environment in ISS orbit and environmental effects on materials and electronic devices to investigate the interaction with and from the environment at the Kibo exposed facility. The payload will be installed on the Japanese Experiment Module's Experiment Logistics Module-Exposed Section, or ELM-ES. The ELM-ES is one of the final components of the Japan Aerospace Exploration Agency's Kibo laboratory for the International Space Station. It can provide payload storage space and can carry up to three payloads at launch. In addition, the ELM-ES provides a logistics function where it can be returned to the ground aboard the space shuttle. The ELM-ES will be carried aboard space shuttle Endeavour on the STS-127 mission targeted for launch May 15. Photo credit: NASA/Cory Huston

  1. KSC-08pd3750

    NASA Image and Video Library

    2008-11-19

    CAPE CANAVERAL, Fla. – In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, workers deploy the mast on the SEDA-AP or Space Environment Data Acquisition equipment--Attached Payload. SEDA-AP will measure space environment in ISS orbit and environmental effects on materials and electronic devices to investigate the interaction with and from the environment at the Kibo exposed facility. The payload will be installed on the Japanese Experiment Module's Experiment Logistics Module-Exposed Section, or ELM-ES. The ELM-ES is one of the final components of the Japan Aerospace Exploration Agency's Kibo laboratory for the International Space Station. It can provide payload storage space and can carry up to three payloads at launch. In addition, the ELM-ES provides a logistics function where it can be returned to the ground aboard the space shuttle. The ELM-ES will be carried aboard space shuttle Endeavour on the STS-127 mission targeted for launch May 15. Photo credit: NASA/Cory Huston

  2. KSC-08pd3752

    NASA Image and Video Library

    2008-11-19

    CAPE CANAVERAL, Fla. – In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, workers check the mast deployment on the SEDA-AP or Space Environment Data Acquisition equipment--Attached Payload. SEDA-AP will measure space environment in ISS orbit and environmental effects on materials and electronic devices to investigate the interaction with and from the environment at the Kibo exposed facility. The payload will be installed on the Japanese Experiment Module's Experiment Logistics Module-Exposed Section, or ELM-ES. The ELM-ES is one of the final components of the Japan Aerospace Exploration Agency's Kibo laboratory for the International Space Station. It can provide payload storage space and can carry up to three payloads at launch. In addition, the ELM-ES provides a logistics function where it can be returned to the ground aboard the space shuttle. The ELM-ES will be carried aboard space shuttle Endeavour on the STS-127 mission targeted for launch May 15. Photo credit: NASA/Cory Huston

  3. To provide for a land exchange with the Trinity Public Utilities District of Trinity County, California, involving the transfer of land to the Bureau of Land Management and the Six Rivers National Forest in exchange for National Forest System land in the Shasta-Trinity National Forest, and for other purposes.

    THOMAS, 112th Congress

    Rep. Herger, Wally [R-CA-2

    2011-03-29

    Senate - 07/24/2012 Received in the Senate and Read twice and referred to the Committee on Energy and Natural Resources. (All Actions) Tracker: This bill has the status Passed HouseHere are the steps for Status of Legislation:

  4. Effects of water temperature on breeding phenology, growth and timing of metamorphosis of foothill yellow-legged frogs (Rana boylii) on the mainstem and selected tributaries of California's Trinity River - 2004-2009.

    Treesearch

    Clara Wheeler; James Bettaso; Donald Ashton; Hartwell Welsh

    2013-01-01

    The cold temperatures maintained in the Trinity River are beneficial to fish but may be problematic for foothill yellow-legged frogs. We examined the timing of breeding, reproductive output, and growth and development of tadpoles for populations of foothill yellow-legged frogs on the mainstem and six tributaries of the Trinity River. On the colder mainstem, onset of...

  5. Flambeau Mining Corporation, Ladysmith, Rusk County, Wisconsin. Proposed Open Pit Copper Mine and Waste Containment Area, Draft Environmental Impact Statement.

    DTIC Science & Technology

    1976-08-01

    American elm Lonicera tatarica - tartarian honeysuckle Ulmus rubra - slippery elm Siiibucus canadenis - common elder Ulmus thoiii~sii - cork elm ...community borders the marshes and swamps. 2.060 The predominant species are the trembling aspen (Populus tremuloides), red maple (Acer rubrum), the elms ...succession. The most numerous trees (in descending order) are: white birch, red maple, aspen, sugar maple, black ash, basswood, elm (Ulmus sp.), hemlock

  6. Professors in the Trenches: Deployed Soldiers and Social Science Academics

    DTIC Science & Technology

    2009-01-01

    CGSC Experiential Learning Model, or ELM . The ELM serves as the methodology for both lesson plan design at the Command and General Staff College and as...the experiential learning model ( ELM ) than the U.S. contractors – the ELM methodology, by design, addresses all four learning style preferences. The...Since the CGSC team used the experiential learning model as the way to teach, they modeled the ELM as they taught all their classes. After the first

  7. Ecological Investigation of a Greentree Reservoir in the Delta National Forest, Mississippi.

    DTIC Science & Technology

    1981-09-01

    elm (Ulmus americana) and slippery elm (U. rubra) oc- curred in the study area, with American elm the more abundant species. No distinction was made...spectively, on both areas (see Appendix C for nomenclature). American elm * and water hickory ranked fifth and sixth in importance on the ref- erence area...between these two species; the label "American elm " includes data for both. 18 boundaries, water hickory increment cores were not analyzed. Table 4

  8. Measurements and modeling of intra-ELM tungsten sourcing and transport in DIII-D

    NASA Astrophysics Data System (ADS)

    Abrams, T.; Leonard, A. W.; Thomas, D. M.; McLean, A. G.; Makowski, M. A.; Wang, H. Q.; Unterberg, E. A.; Briesemeister, A. R.; Rudakov, D. L.; Bykov, I.; Donovan, D.

    2017-10-01

    Intra-ELM tungsten erosion profiles in the DIII-D divertor, acquired via W I spectroscopy with high temporal and spatial resolution, are consistent with SDTrim.SP sputtering modeling using measured ion saturation currents and impact energies during ELMs as input and an ad-hoc 2% C2+ impurity flux. The W sputtering profile peaks close to the OSP both during and between ELMs in the favorable BT direction. In reverse BT the W source peaks close to the OSP between ELMs but strongly broadens and shifts outboard during ELMs, heuristically consistent with radially outward ion transport via ExB drifts. Ion impact energies during ELMs (inferred taking the ratio of divertor heat flux to the ion saturation current) are found to be approximately equal to Te,ped, lower than the 4*Te,ped value predicted by the Fundamenski/Moulton free streaming model. These impact energies imply both D main ions and C impurities contribute strongly to W sputtering during ELMs on DIII-D. This work represents progress towards a predictive model to link upstream conditions (i.e., pedestal height) and SOL impurity levels to the ELM-induced W impurity source at both the strike-point and far-target regions in the ITER divertor. Correlations between ELM size/frequency and SOL W fluxes measured via a midplane deposition probe will also be presented. Work supported by US DOE under DE-FC02-04ER54698.

  9. Prompt triggering of edge localized modes through lithium granule injection on EAST

    NASA Astrophysics Data System (ADS)

    Lunsford, Robert; Sun, Z.; Hu, J. S.; Xu, W.; Zuo, G. Z.; Gong, X. Z.; Wan, B. N.; Li, J. G.; Huang, M.; Maingi, R.; Diallo, A.; Tritz, K.; the EAST Team

    2017-10-01

    We report successful triggering of edge localized mode (ELMs) in EAST with Lithium (Li) micropellets, and the observed dependence of ELM triggering efficiency on granule size. ELM control is essential for successful ITER operation throughout the entire campaign, relying on magnetic perturbations for ELM suppression and ELM frequency enhancement via pellet injection. To separate the task of fueling from ELM pacing, we initiate the prompt generation of ELMs via impurity granule injection. Lithium granules ranging in size from 200 - 1000 microns are mechanically injected into upper-single null EAST long pulse H-mode discharges. The injections are monitored for their effect on high Z impurity accumulation and to assess the pressure perturbation required for reliable ELM triggering. We have determined that granules of diameter larger than 600 microns (corresponding to 5.2 x 1018 Li atoms) are successful at triggering ELMs more than 90% of the time. The triggering efficiency drops precipitously to less than 40% as the granule size is reduced to 400 microns (1.5 x 1018 Li atoms), indicating a triggering threshold has been crossed. Using this information an optimal impurity granule size which will regularly trigger a prompt ELM in these EAST discharges is determined. Coupling these results with alternate discharge scenarios on EAST and similar experiments performed on DIII-D provides the possibility of extrapolation to future devices.

  10. Elm leaf beetle performance on ozone-fumigated elm

    Treesearch

    Jack H. Barger; Richard W. Hall; Alden M. Townsend; Alden M. Townsend

    1992-01-01

    Leaves (1986) from elm hybrids ('Pioneer', 'Homestead', '970') previously fumigated in open-top chambers with ozone or with charcoal-filtered air (CFA) were evaluated for water and nitrogen content or were fed to adult elm leaf beetles (ELB), Xanthogaleruca = (Pyrrhallta) luteola (Muller), to determine host suitability for beetle fecundity...

  11. Using Dutch elm disease-tolerant elm to restore floodplains impacted by emerald ash borer

    Treesearch

    Kathleen S. Knight; James M. Slavicek; Rachel Kappler; Elizabeth Pisarczyk; Bernadette Wiggin; Karen. Menard

    2012-01-01

    American elm (Ulmus Americana L.) was a dominant species in floodplains and swamps of the Midwest before Dutch elm disease (DED) (Ophiostoma ulmi and O.novo-ulmi) reduced its populations. In many areas, ash (Fraxinus spp.) became dominant in these ecosystems. Emerald ash borer (EAB) (...

  12. 75 FR 27814 - Trinity Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-18

    ..., 2010. ADDRESSES: The meeting will be held at the Trinity County Library, 211 Main St., Weaverville, CA... include discussion of the following topics: TRRP budget; Science program proposals and work plan...

  13. A Study of Vegetation Development in Relation to Age of River Stabilization Structures Along a Channelized Segment of the Missouri River.

    DTIC Science & Technology

    1975-01-25

    s.ame time period, the first shrub species begin to appear in the sites. Ulmus rubra ( slippery elm ), Celtis occidentalis (hackberry), and Platanus...boxelder), Ulmus americana (American elm ), Ulmus rubra ( slippery elm ), Fra:inus pennsyl- vanica (green ash), and Juglans nigra (black walnut). These may...be replaced by Tilia americana (basswood), the Ulmus americana (American elm ) and Ulmus rubra ( slippery elm ) remaining as co- dominants. Weaver (1960

  14. Trinity | Informatics Technology for Cancer Research (ITCR)

    Cancer.gov

    Trinity Cancer Transcriptome Analysis Toolkit (CTAT) including de novo transcriptome assembly with downstream support for expression analysis and focused analyses on cancer transcriptomes, incorporating mutation and fusion transcript discovery, and single cell analysis.

  15. 4. Photocopy of measured drawing (original in possession of Trinity ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. Photocopy of measured drawing (original in possession of Trinity Episcopal Cathedral) Edward Tuckerman Potter, architect ca. 1867 WEST FACADE, ELEVATION - Grace Episcopal Cathedral, 1121 Main Street, Davenport, Scott County, IA

  16. LLNL Mercury Project Trinity Open Science Final Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Brantley, Patrick; Dawson, Shawn; McKinley, Scott

    2016-04-20

    The Mercury Monte Carlo particle transport code developed at Lawrence Livermore National Laboratory (LLNL) is used to simulate the transport of radiation through urban environments. These challenging calculations include complicated geometries and require significant computational resources to complete. As a result, a question arises as to the level of convergence of the calculations with Monte Carlo simulation particle count. In the Trinity Open Science calculations, one main focus was to investigate convergence of the relevant simulation quantities with Monte Carlo particle count to assess the current simulation methodology. Both for this application space but also of more general applicability, wemore » also investigated the impact of code algorithms on parallel scaling on the Trinity machine as well as the utilization of the Trinity DataWarp burst buffer technology in Mercury via the LLNL Scalable Checkpoint/Restart (SCR) library.« less

  17. Modeling of Plasma Pressure Effects on ELM Suppression With RMP in DIII-D

    NASA Astrophysics Data System (ADS)

    Orlov, D. M.; Moyer, R. A.; Mordijck, S.; Evans, T. E.; Osborne, T. H.; Snyder, P. B.; Unterberg, E. A.; Fenstermacher, M. E.

    2009-11-01

    Resonant magnetic perturbations (RMPs) are used to control the pedestal pressure gradient in both low and high (ν3^*) DIII-D plasmas. In this work we have analyzed several discharges with different levels of triangularity, different neutral beam injection power levels, and with, βN ranging from 1.5 to 2.3. The field line integration code TRIP3D was used to model the magnetic perturbation in ELMing and ELM suppressed phases during the RMP pulse. The results of this modeling showed very little effect of βN on the structure of the vacuum magnetic field during ELM suppression using n=3 RMPs. Kinetic equilibrium reconstructions showed a decrease in bootstrap current during RMP. Linear peeling-ballooning stability analysis performed with the ELITE code suggested that the ELMs, which persist during RMP, i.e. ELMing still is observed, are not Type I ELMs. Identification of these Dα spikes is an ongoing work.

  18. Meta-cognitive online sequential extreme learning machine for imbalanced and concept-drifting data classification.

    PubMed

    Mirza, Bilal; Lin, Zhiping

    2016-08-01

    In this paper, a meta-cognitive online sequential extreme learning machine (MOS-ELM) is proposed for class imbalance and concept drift learning. In MOS-ELM, meta-cognition is used to self-regulate the learning by selecting suitable learning strategies for class imbalance and concept drift problems. MOS-ELM is the first sequential learning method to alleviate the imbalance problem for both binary class and multi-class data streams with concept drift. In MOS-ELM, a new adaptive window approach is proposed for concept drift learning. A single output update equation is also proposed which unifies various application specific OS-ELM methods. The performance of MOS-ELM is evaluated under different conditions and compared with methods each specific to some of the conditions. On most of the datasets in comparison, MOS-ELM outperforms the competing methods. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Ten-year performance of the United States national elm trial

    Treesearch

    Jason J. Griffin; William R. Jacobi; E. Gregory McPherson; Clifford S. Sadof; James R. McKenna; Mark L. Gleason; Nicole Ward Gauthier; Daniel A. Potter; David R. Smitley; Gerard C. Adams; Ann Brooks Gould; Christian R. Cash; James A. Walla; Mark C. Starrett; Gary Chastagner; Jeff L. Sibley; Vera A. Krischik; Adam F. Newby

    2017-01-01

    Ulmus americana (American elm) was an important urban tree in North America prior to the introduction of the Dutch elm disease pathogen in 1930. Subsequently, urban and community forests were devastated by the loss of large canopies. Tree improvement programs produced disease tolerant American and Eurasian elm cultivars and introduced them into the...

  20. FRONT ELEVATION OF RESIDENCE, SHOWING ELM DRIVE AND SIDEWALK IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    FRONT ELEVATION OF RESIDENCE, SHOWING ELM DRIVE AND SIDEWALK IN THE FOREGROUND. VIEW FACING NORTH - Camp H.M. Smith and Navy Public Works Center Manana Title VII (Capehart) Housing, Three-Bedroom Single-Family Types 8 and 11, Birch Circle, Elm Drive, Elm Circle, and Date Drive, Pearl City, Honolulu County, HI

  1. Establishment and characterization of American elm cell suspension cultures

    Treesearch

    Steven M. Eshita; Joseph C. Kamalay; Vicki M. Gingas; Daniel A. Yaussy

    2000-01-01

    Cell suspension cultures of Dutch elm disease (DED)-tolerant and DED-susceptible American elms clones have been established and characterized as prerequisites for contrasts of cellular responses to pathogen-derived elicitors. Characteristics of cultured elm cell growth were monitored by A700 and media conductivity. Combined cell growth data for all experiments within a...

  2. Novel insights into the Elm Yellows phytoplasma genome and into the metagenome of Elm Yellows-infected elms

    USDA-ARS?s Scientific Manuscript database

    In North America, American elms were historically present throughout the northeastern United States and southeastern Canada. The longevity of these trees, their resistance to the harsh urban environment, and their aesthetics led to their wide use in landscaping and streetscaping over several decade...

  3. Modeling carbon production and transport during ELMs in DIII-D

    NASA Astrophysics Data System (ADS)

    Hogan, J.; Wade, M.; Coster, D.; Lasnier, C.

    2004-11-01

    Large-scale Type I ELM events could provide a significant C source in ITER, and C production rates depend on incident D flux density and surface temperature, quantities which can vary significantly during an ELM event. Recent progress on DIII-D has improved opportunities for code comparison. Fast time-scale measurements of divertor CIII evolution [1] and fast edge CER measurements of C profile evolution during low-density DIII-D LSN ELMy H-modes (type I) [2] have been modeled using the solps5.0/Eirene99 coupled edge code and time dependent thermal analysis codes. An ELM model based on characteristics of MHD peeling-ballooning modes reproduces the pedestal evolution. Qualitative agreement for the CIII evolution during an ELM event is found using the Roth et al annealing model for chemical sputtering and the sensitivity to other models is described. Significant ELM-to-ELM variations in observed maximum divertor target IR temperature during nominally identical ELMs are investigated with models for C emission from micron-scale dust particles. [1] M Groth, M Fenstermacher et al J Nucl Mater 2003, [2] M Wade, K Burrell et al PSI-16

  4. Trends in extreme learning machines: a review.

    PubMed

    Huang, Gao; Huang, Guang-Bin; Song, Shiji; You, Keyou

    2015-01-01

    Extreme learning machine (ELM) has gained increasing interest from various research fields recently. In this review, we aim to report the current state of the theoretical research and practical advances on this subject. We first give an overview of ELM from the theoretical perspective, including the interpolation theory, universal approximation capability, and generalization ability. Then we focus on the various improvements made to ELM which further improve its stability, sparsity and accuracy under general or specific conditions. Apart from classification and regression, ELM has recently been extended for clustering, feature selection, representational learning and many other learning tasks. These newly emerging algorithms greatly expand the applications of ELM. From implementation aspect, hardware implementation and parallel computation techniques have substantially sped up the training of ELM, making it feasible for big data processing and real-time reasoning. Due to its remarkable efficiency, simplicity, and impressive generalization performance, ELM have been applied in a variety of domains, such as biomedical engineering, computer vision, system identification, and control and robotics. In this review, we try to provide a comprehensive view of these advances in ELM together with its future perspectives.

  5. SIGNIFICANCE OF PREOPERATIVE EXTERNAL LIMITING MEMBRANE HEIGHT ON VISUAL PROGNOSIS IN PATIENTS UNDERGOING MACULAR HOLE SURGERY.

    PubMed

    Geenen, Caspar; Murphy, Declan C; Sandinha, Maria T; Rees, Jon; Steel, David H W

    2018-03-05

    To investigate the association between the vertical elevation of the external limiting membrane (ELM) and visual outcome in patients undergoing surgery for idiopathic full-thickness macular hole. Retrospective observational study of a consecutive cohort of patients undergoing vitrectomy to treat macular hole. The greatest vertical height of the central ELM above the retinal pigment epithelium (ELM height) was measured on spectral domain optical coherence tomography preoperatively. The relationship of ELM height to other preoperative and postoperative variables, including macular hole width and height, and visual acuity was analyzed. Data from 91 eyes of 91 patients who had undergone successful hole closure were included. The mean ELM height was 220 μm (range 100-394). There were significant correlations between the ELM height and the diameter of the hole, hole height, and worsening preoperative visual acuity. For holes less than 400 μm in width, better postoperative visual acuity was significantly predicted by a lower ELM height. The ELM height varies widely in idiopathic macular hole. It is higher in eyes where the hole is wider and also when the hole itself is higher. For holes of less than 400 μm in width, a lower ELM height is a strong independent predictor of a good postoperative outcome.

  6. The Relationships Between ELM Suppression, Pedestal Profiles, and Lithium Wall Coatings in NSTX

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    D.P. Boyle, R. Maingi, P.B. Snyder, J. Manickam, T.H. Osborne, R.E. Bell, B.P. LeBlanc, and the NSTX Team

    2012-08-17

    Recently in the National Spherical Torus Experiment (NSTX), increasing lithium wall coatings suppressed edge localized modes (ELMs), gradually but not quite monotonically. This work details profile and stability analysis as ELMs disappeared throughout the lithium scan. While the quantity of lithium deposited between discharges did not uniquely determine the presence of ELMs, profile analysis demonstrated that lithium was correlated to wider density and pressure pedestals with peak gradients farther from the separatrix. Moreover, the ELMy and ELM-free discharges were cleanly separated by their density and pedestal widths and peak gradient locations. Ultimately, ELMs were only suppressed when lithium caused themore » density pedestal to widen and shift inward. These changes in the density gradient were directly reflected in the pressure gradient and calculated bootstrap current. This supports the theory that ELMs in NSTX are caused by peeling and/or ballooning modes, as kink/peeling modes are stabilized when the edge current and pressure gradient shift away from the separatrix. Edge stability analysis using ELITE corroborated this picture, as reconstructed equilibria from ELM-free discharges were generally farther from their kink/peeling stability boundaries than ELMy discharges. We conclude that density profile control provided by lithium is the key first step to ELM suppression in NSTX« less

  7. Quantitative thickness prediction of tectonically deformed coal using Extreme Learning Machine and Principal Component Analysis: a case study

    NASA Astrophysics Data System (ADS)

    Wang, Xin; Li, Yan; Chen, Tongjun; Yan, Qiuyan; Ma, Li

    2017-04-01

    The thickness of tectonically deformed coal (TDC) has positive correlation associations with gas outbursts. In order to predict the TDC thickness of coal beds, we propose a new quantitative predicting method using an extreme learning machine (ELM) algorithm, a principal component analysis (PCA) algorithm, and seismic attributes. At first, we build an ELM prediction model using the PCA attributes of a synthetic seismic section. The results suggest that the ELM model can produce a reliable and accurate prediction of the TDC thickness for synthetic data, preferring Sigmoid activation function and 20 hidden nodes. Then, we analyze the applicability of the ELM model on the thickness prediction of the TDC with real application data. Through the cross validation of near-well traces, the results suggest that the ELM model can produce a reliable and accurate prediction of the TDC. After that, we use 250 near-well traces from 10 wells to build an ELM predicting model and use the model to forecast the TDC thickness of the No. 15 coal in the study area using the PCA attributes as the inputs. Comparing the predicted results, it is noted that the trained ELM model with two selected PCA attributes yields better predication results than those from the other combinations of the attributes. Finally, the trained ELM model with real seismic data have a different number of hidden nodes (10) than the trained ELM model with synthetic seismic data. In summary, it is feasible to use an ELM model to predict the TDC thickness using the calculated PCA attributes as the inputs. However, the input attributes, the activation function and the number of hidden nodes in the ELM model should be selected and tested carefully based on individual application.

  8. Evaluation of extreme learning machine for classification of individual and combined finger movements using electromyography on amputees and non-amputees.

    PubMed

    Anam, Khairul; Al-Jumaily, Adel

    2017-01-01

    The success of myoelectric pattern recognition (M-PR) mostly relies on the features extracted and classifier employed. This paper proposes and evaluates a fast classifier, extreme learning machine (ELM), to classify individual and combined finger movements on amputees and non-amputees. ELM is a single hidden layer feed-forward network (SLFN) that avoids iterative learning by determining input weights randomly and output weights analytically. Therefore, it can accelerate the training time of SLFNs. In addition to the classifier evaluation, this paper evaluates various feature combinations to improve the performance of M-PR and investigate some feature projections to improve the class separability of the features. Different from other studies on the implementation of ELM in the myoelectric controller, this paper presents a complete and thorough investigation of various types of ELMs including the node-based and kernel-based ELM. Furthermore, this paper provides comparisons of ELMs and other well-known classifiers such as linear discriminant analysis (LDA), k-nearest neighbour (kNN), support vector machine (SVM) and least-square SVM (LS-SVM). The experimental results show the most accurate ELM classifier is radial basis function ELM (RBF-ELM). The comparison of RBF-ELM and other well-known classifiers shows that RBF-ELM is as accurate as SVM and LS-SVM but faster than the SVM family; it is superior to LDA and kNN. The experimental results also indicate that the accuracy gap of the M-PR on the amputees and non-amputees is not too much with the accuracy of 98.55% on amputees and 99.5% on the non-amputees using six electromyography (EMG) channels. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Observations of the effect of lower hybrid waves on ELM behaviour in EAST

    NASA Astrophysics Data System (ADS)

    Chen, R.; Xu, G. S.; Liang, Y.; Wang, H. Q.; Zhou, C.; Liu, A. D.; Wang, L.; Qian, J. P.; Gan, K. F.; Yang, J. H.; Duan, Y. M.; Li, Y. L.; Ding, S. Y.; Wu, X. Q.; Yan, N.; Chen, L.; Shao, L. M.; Zhang, W.; Hu, G. H.; Zhao, N.; Liu, S. C.; Kong, D. F.; Gong, X. Z.

    2015-03-01

    Dedicated experiments focusing on the influence of lower hybrid waves (LHWs) on edge-localized modes (ELMs) were first performed during the 2012 experimental campaign of EAST, via modulating the input power of LHWs in the high-confinement-mode (H-mode) plasma mainly sustained by ion cyclotron resonant heating. Natural ELMs are effectively mitigated (ELM frequency increases, while its intensity decreases dramatically) as the LHW is applied, observed over a fairly wide range of plasma current or edge safety factor. By scanning the modulation frequency (fm) of LHW injected power in a target plasma dominated by the so-called small ELMs, we conclude that large ELMs with markedly larger amplitudes and lower frequencies are reproduced at low modulation frequencies (fm < 100 Hz). Analysis of the evolution of edge extreme ultraviolet radiation signals further indicates that plasma fluctuations at the pedestal region indistinctively respond to rapid modulation (fm ⩾ 100 Hz) of LHW injected power. This is proposed as the mechanism responsible for the observed fm dependence of the mitigation effect induced by LHWs on large ELMs. In addition, a critical threshold of LHW input power PLHW is estimated as PLHWthr≃800 kW , beyond which the impact of applied LHWs on ELM behaviours can be achieved. Finally, Langmuir probe measurements suggest that, rather than the concentration of free energy into a narrowband quasi-coherent precursor commonly observed growing until the ELM crash, the continuous development of broadband turbulence during the ELM-absent phase with the application of LHWs might contribute to the avoidance of ELM crashes. These results present new insights into existing experiments, and also provide some foundations and references for the next-step research about exploring in more depth and improving this new attractive method to effectively control the ELM-induced very large transient heat and particle flux.

  10. Suppressive response of confections containing the extractive from leaves of Morus Alba on postprandial blood glucose and insulin in healthy human subjects

    PubMed Central

    Nakamura, Mariko; Nakamura, Sadako; Oku, Tsuneyuki

    2009-01-01

    Background The first aim of this study was to clarify the effective ratio of extractive from leaves of Morus Alba (ELM) to sucrose so as to apply this knowledge to the preparation of confections that could effectively suppress the elevation of postprandial blood glucose and insulin. The second aim was to identify the efficacy of confections prepared with the optimally effective ratio determined from the first study, using healthy human subjects. Methods Ten healthy females (22.3 years, BMI 21.4 kg/m2) participated in this within-subject, repeated measures study. For the first aim of this study, the test solutions containing 30 g of sucrose and 1.2 or 3.0 g of ELM were repeatedly and randomly given to each subject. To identify the practically suppressive effects on postprandial blood glucose and insulin, some confections with added ELM were prepared as follows: Mizu-yokan, 30 g of sucrose with the addition of 1.5 or 3.0 g ELM; Daifuku-mochi, 9.0 g of starch in addition to 30 g of sucrose and 1.5 or 3.0 g ELM; Chiffon-cake, 24 g of sucrose, starch, and 3.0 or 6.0 g of ELM, and were ingested by each subject. Blood and end-expiration were collected at selected periods after test food ingestion. Results When 30 g of sucrose with 1.2 or 3.0 g of ELM were ingested by subjects, the elevations of postprandial blood glucose and insulin were effectively suppressed (p < 0.01), and the most effective ratio of ELM to sucrose was evaluated to be 1:10. AUC (area under the curve) of breath hydrogen excretion for 6 h after the ingestion of an added 3 g of ELM significantly increased (p < 0.01). When AUCs-3h of incremental blood glucose of confections without ELM was 100, that of Mizu-yokan and Daifuku-mochi with the ratio (1:10) of ELM to sucrose was decreased to 53.4 and 58.2, respectively. Chiffon-cake added one-fourth ELM was 29.0. Conclusion ELM-containing confections for which the ratio of ELM and sucrose is one-tenth effectively suppress the postprandial blood glucose and insulin by inhibiting the intestinal sucrase, thus creating a prebiotic effect. The development of confections with ELM can therefore contribute to the prevention and the quality of life for prediabetic and diabetic patients. PMID:19602243

  11. 5. Photocopy of measured drawing (original in possession of Trinity ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. Photocopy of measured drawing (original in possession of Trinity Episcopal Cathedral) Edward Tuckerman Potter, architect ca. 1867 CROSS SECTION, LOOKING NORTH - Grace Episcopal Cathedral, 1121 Main Street, Davenport, Scott County, IA

  12. Source and Message Factors in Persuasion: A Reply to Stiff's Critique of the Elaboration Likelihood Model.

    ERIC Educational Resources Information Center

    Petty, Richard E.; And Others

    1987-01-01

    Answers James Stiff's criticism of the Elaboration Likelihood Model (ELM) of persuasion. Corrects certain misperceptions of the ELM and criticizes Stiff's meta-analysis that compares ELM predictions with those derived from Kahneman's elastic capacity model. Argues that Stiff's presentation of the ELM and the conclusions he draws based on the data…

  13. American elm clones of importance in Dutch elm disease tolerance studies

    Treesearch

    Linda M. Haugen; Susan E. Bentz

    2017-01-01

    We present the background and characteristics of American elm clones that are commercially available or of interest in research on Dutch elm disease (DED) tolerance in the United States. The characteristics of interest include origin, ploidy level, whether available in nursery trade, evidence of DED tolerance, and other comments. The list includes 10 named commercially...

  14. First Results of ELM Triggering With a Multichamber Lithium Granule Injector Into EAST Discharges

    DOE PAGES

    Sun, Z.; Lunsford, R.; Maingi, R.; ...

    2017-12-12

    A critical challenge facing the basic long-pulse H-mode for ITER is to control edge-localized modes (ELMs). A new method using a multichamber lithium (Li) granule injector (LGI) for ELM triggering experiments has been developed in Experimental Advanced Superconducting Tokamak (EAST). First experimental results of the control of ELMs are obtained in EAST with a tungsten divertor. It is found that the injector has good capacities, i.e., allowing good flexibilities in granule size selection, injection rate, and injection velocity. In conclusion, LGI has successfully triggered ELMs during the H-mode. These results indicate the LGI would be a promising method to controlmore » ELMs in long-pulse steady-state tokamaks.« less

  15. First Results of ELM Triggering With a Multichamber Lithium Granule Injector Into EAST Discharges

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sun, Z.; Lunsford, R.; Maingi, R.

    A critical challenge facing the basic long-pulse H-mode for ITER is to control edge-localized modes (ELMs). A new method using a multichamber lithium (Li) granule injector (LGI) for ELM triggering experiments has been developed in Experimental Advanced Superconducting Tokamak (EAST). First experimental results of the control of ELMs are obtained in EAST with a tungsten divertor. It is found that the injector has good capacities, i.e., allowing good flexibilities in granule size selection, injection rate, and injection velocity. In conclusion, LGI has successfully triggered ELMs during the H-mode. These results indicate the LGI would be a promising method to controlmore » ELMs in long-pulse steady-state tokamaks.« less

  16. Phylogeography: English elm is a 2,000-year-old Roman clone.

    PubMed

    Gil, Luis; Fuentes-Utrilla, Pablo; Soto, Alvaro; Cervera, M Teresa; Collada, Carmen

    2004-10-28

    The outbreak of Dutch elm disease in the 1970s ravaged European elm populations, killing more than 25 million trees in Britain alone; the greatest impact was on Ulmus procera, otherwise known as the English elm. Here we use molecular and historical information to show that this elm derives from a single clone that the Romans transported from Italy to the Iberian peninsula, and from there to Britain, for the purpose of supporting and training vines. Its highly efficient vegetative reproduction and its inability to set seeds have preserved this clone unaltered for 2,000 years as the core of the English elm population--and the preponderance of this susceptible variety may have favoured a rapid spread of the disease.

  17. Geologic history and hydrogeologic setting of the Edwards-Trinity aquifer system, west-central Texas

    USGS Publications Warehouse

    Barker, R.A.; Bush, P.W.; Baker, E.T.

    1994-01-01

    Because the diagenetic effects of cementation, recrystallization, and mineral replacement diminish the hydraulic conductivity of most rocks composing the Trinity and Edwards-Trinity aquifers, transmissivity values average less than 10,000 feet squared per day over more than 90 percent of the study area. However, the effects of tectonic fractures and dissolution in the Balcones fault zone cause transmissivity values to average about 750,000 feet squared per day in the Edwards aquifer, which occupies less than 10 percent of the study area.

  18. Use of watershed factors to predict consumer surfactant risk, water quality, and habitat quality in the upper Trinity River, Texas.

    PubMed

    Atkinson, S F; Johnson, D R; Venables, B J; Slye, J L; Kennedy, J R; Dyer, S D; Price, B B; Ciarlo, M; Stanton, K; Sanderson, H; Nielsen, A

    2009-06-15

    Surfactants are high production volume chemicals that are used in a wide assortment of "down-the-drain" consumer products. Wastewater treatment plants (WWTPs) generally remove 85 to more than 99% of all surfactants from influents, but residual concentrations are discharged into receiving waters via wastewater treatment plant effluents. The Trinity River that flows through the Dallas-Fort Worth metropolitan area, Texas, is an ideal study site for surfactants due to the high ratio of wastewater treatment plant effluent to river flow (>95%) during late summer months, providing an interesting scenario for surfactant loading into the environment. The objective of this project was to determine whether surfactant concentrations, expressed as toxic units, in-stream water quality, and aquatic habitat in the upper Trinity River could be predicted based on easily accessible watershed characteristics. Surface water and pore water samples were collected in late summer 2005 at 11 sites on the Trinity River in and around the Dallas-Fort Worth metropolitan area. Effluents of 4 major waste water treatment plants that discharge effluents into the Trinity River were also sampled. General chemistries and individual surfactant concentrations were determined, and total surfactant toxic units were calculated. GIS models of geospatial, anthropogenic factors (e.g., population density) and natural factors (e.g., soil organic matter) were collected and analyzed according to subwatersheds. Multiple regression analyses using the stepwise maximum R(2) improvement method were performed to develop prediction models of surfactant risk, water quality, and aquatic habitat (dependent variables) using the geospatial parameters (independent variables) that characterized the upper Trinity River watershed. We show that GIS modeling has the potential to be a reliable and inexpensive method of predicting water and habitat quality in the upper Trinity River watershed and perhaps other highly urbanized watersheds in semi-arid regions.

  19. High frequency pacing of edge localized modes by injection of lithium granules in DIII-D H-mode discharges

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bortolon, A.; Maingi, R.; Mansfield, D. K.

    A newly installed Lithium Granule Injector (LGI) was used to pace edge localized modes (ELM) in DIII-D. ELM pacing efficiency was studied injecting lithium granules of nominal diameter 0.3–0.9mm, speed of 50–120 m s -1 and average injection rates up to 100 Hz for 0.9mm granules and up to 700 Hz for 0.3mm granules. The efficiency of ELM triggering was found to depend strongly on size of the injected granules, with triggering efficiency close to 100% obtained with 0.9mm diameter granules, lower with smaller sizes, and weakly depending on granule velocity. Robust ELM pacing was demonstrated in ITER-like plasmas formore » the entire shot length, at ELM frequencies 3–5 times larger than the ‘natural’ ELM frequency observed in reference discharges. Within the range of ELM frequencies obtained, the peak ELM heat flux at the outer strike point was reduced with increasing pacing frequency. The peak heat flux reduction at the inner strike point appears to saturate at high pacing frequency. Lithium was found in the plasma core, with a concurrent reduction of metallic impurities and carbon. Altogether, high frequency ELM pacing using the lithium granule injection appears to be compatible with both H-mode energy confinement and attractive H-mode pedestal characteristics, but further assessment is need« less

  20. High frequency pacing of edge localized modes by injection of lithium granules in DIII-D H-mode discharges

    DOE PAGES

    Bortolon, A.; Maingi, R.; Mansfield, D. K.; ...

    2016-04-08

    A newly installed Lithium Granule Injector (LGI) was used to pace edge localized modes (ELM) in DIII-D. ELM pacing efficiency was studied injecting lithium granules of nominal diameter 0.3–0.9mm, speed of 50–120 m s -1 and average injection rates up to 100 Hz for 0.9mm granules and up to 700 Hz for 0.3mm granules. The efficiency of ELM triggering was found to depend strongly on size of the injected granules, with triggering efficiency close to 100% obtained with 0.9mm diameter granules, lower with smaller sizes, and weakly depending on granule velocity. Robust ELM pacing was demonstrated in ITER-like plasmas formore » the entire shot length, at ELM frequencies 3–5 times larger than the ‘natural’ ELM frequency observed in reference discharges. Within the range of ELM frequencies obtained, the peak ELM heat flux at the outer strike point was reduced with increasing pacing frequency. The peak heat flux reduction at the inner strike point appears to saturate at high pacing frequency. Lithium was found in the plasma core, with a concurrent reduction of metallic impurities and carbon. Altogether, high frequency ELM pacing using the lithium granule injection appears to be compatible with both H-mode energy confinement and attractive H-mode pedestal characteristics, but further assessment is need« less

  1. Numerical Analysis of the Effects of Normalized Plasma Pressure on RMP ELM Suppression in DIII-D

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Orlov, D. M.; Moyer, R.A.; Evans, T. E.

    2010-01-01

    The effect of normalized plasma pressure as characterized by normalized pressure parameter (beta(N)) on the suppression of edge localized modes (ELMs) using resonant magnetic perturbations (RMPs) is studied in low-collisionality (nu* <= 0.2) H-mode plasmas with low-triangularity ( = 0.25) and ITER similar shapes ( = 0.51). Experimental results have suggested that ELM suppression by RMPs requires a minimum threshold in plasma pressure as characterized by beta(N). The variations in the vacuum field topology with beta(N) due to safety factor profile and island overlap changes caused by variation of the Shafranov shift and pedestal bootstrap current are examined numerically withmore » the field line integration code TRIP3D. The results show very small differences in the vacuum field structure in terms of the Chirikov (magnetic island overlap) parameter, Poincare sections and field line loss fractions. These differences do not appear to explain the observed threshold in beta(N) for ELM suppression. Linear peeling-ballooning stability analysis with the ELITE code suggests that the ELMs which persist during the RMPs when beta(N) is below the observed threshold are not type I ELMs, because the pedestal conditions are deep within the stable regime for peeling-ballooning modes. These ELMs have similarities to type III ELMs or low density ELMs.« less

  2. Antibiotic Injections Control Elm Phloem Necrosis in the Urban Ecosystem

    Treesearch

    T. H. Filer

    1976-01-01

    When nine American and cedar elms showing symptoms of elm phloem necrosis were given repeated injections of tetracycline antibiotics for several years, all treated trees recovered and appeared healthy by 1976. All but one of the untreated checks died. Of 10 severely infected American elms treated only during the summer of 1972, seven died and the other three showed...

  3. The Italian elm breeding program for Dutch elm disease resistance

    Treesearch

    Alberto Santini; Francesco Pecori; Luisa Ghelardini

    2012-01-01

    In the 20th century, elms across Europe and North America were devastated by two pandemics of Dutch elm disease (DED), caused by the introduction of two fungal pathogens: Ophiostoma ulmi, followed by O. novo-ulmi. At the end of 1920s, research into a resistance to DED began in Europe and then in the United States. No...

  4. Generation of American elm trees with tolerance to Dutch elm disease through controlled crosses and selection

    Treesearch

    James M. Slavicek; Kathleen S. Knight

    2012-01-01

    The goal of our research and development efforts is to generate new and/or improved selections of the American elm (Ulmus americana L.) with tolerance/resistance to Dutch elm disease (DED). The approaches we are taking for this effort include: 1) controlled breeding using known DED -tolerant selections, 2) controlled breeding using DED-tolerant...

  5. Pressure injection of methyl 2-benzimidazole carbamate hydrochloride solution as a control for Dutch elm disease

    Treesearch

    Garold F. Gregory; Thomas W. Jones

    1973-01-01

    A preliminary evaluation of the effectiveness of injecting methyl 2-benzimidazole carbamate hydrochloride solution into elms for prevention or cure of Dutch elm disease is reported. Symptom development was diminished or prevented in elms injected with fungicide before inoculation. Symptom development was arrested in all crown-inoculated diseased trees injected with the...

  6. The ecological role of American elm (Ulmus americana L.) in floodplain forests of northeastern North America

    Treesearch

    Christian O. Marks

    2017-01-01

    Before Dutch elm disease, the American elm (Ulmus americana L.) was a leading dominant tree species in the better drained parts of floodplain forests where flooding occurs about 1 percent of the time. Although still common in these habitats today, U. americana now rarely lives long enough to reach the forest canopy because elm...

  7. Development of methods for the restoration of the American elm in forested landscapes

    Treesearch

    James M. Slavicek

    2013-01-01

    A project was initiated in 2003 to establish test sites to develop methods to reintroduce the American elm (Ulmus americana L.) in forested landscapes. American elm tree strains with high levels of tolerance to Dutch elm disease (DED) were established in areas where the trees can naturally regenerate and spread. The process of regeneration will...

  8. Study of ELM Density Turbulence using the Upgraded Phase Contrast Imaging on DIII-D

    NASA Astrophysics Data System (ADS)

    Rost, J. C.; Davis, E. M.; Marinoni, A.; Porkolab, M.; Burrell, K. H.

    2016-10-01

    Recent studies of the turbulent density fluctuations accompanying ELMs in mixed ELM-type discharges have exploited the expanded wavenumber range of the upgraded Phase Contrast Imaging (PCI) diagnostic. The PCI data demonstrate the difference between the fluctuations generated by Type I ELMs, which are broadband in frequency and wavelength, and those generated by Type III ELMs, which are similar in amplitude but restricted to long wavelengths, suggesting that turbulence may play a significant role in Type I ELM transport. The high frequency response of PCI makes it ideal for studying the ELM-associated density fluctuations, which are observed at frequencies up to several MHz, evolve on time scales of 10s of μs, and persist after the magnetic component of the ELM has decayed away. The upgraded PCI, with independent systems for long and short wavelength detection (k < 5 cm-1 and 1 < k < 30 cm-1 respectively), demonstrated coverage of the full wavenumber range of interest. Work supported in part by the US Department of Energy under DE-FG02-94ER54235, DE-FC02-04ER54698, and DE-FC02-99ER54512.

  9. ELM Mitigation in Low-rotation ITER Baseline Scenario Plasmas on DIII-D with Deuterium Pellet Injection

    NASA Astrophysics Data System (ADS)

    Baylor, L. R.

    2016-10-01

    ELM mitigation using high frequency D2 pellet ELM pacing has been demonstrated in ITER baseline scenario plasmas on DIII D with low rotation obtained with low NBI input torque. The ITER burning plasmas will have relatively low input torque and are expected to have low rotation. ELM mitigation by on-demand pellet ELM triggering has not been observed before in these conditions. New experiments on DIII-D in these conditions with 90 Hz D2 pellets have shown that significant mitigation of the divertor ELM peak heat flux by a factor of 8 is possible without detrimental effects to the plasma confinement. High-Z impurity accumulation is dramatically reduced at all input torques from 0.1 to 2.5 N-m. Fueling with high field side injection of D2 pellets has been employed to demonstrate that density buildup can be obtained simultaneously with ELM mitigation. The implications are that rapid pellet injection remains a promising technique to trigger on-demand ELMs in low rotating plasmas with greatly reduced peak flux while preventing impurity accumulation in ITER. Supported by the US DOE under DE-AC05-00OR22725, DE-FC02-04ER54698.

  10. ELM elimination with Li powder injection in EAST discharges using the tungsten upper divertor

    DOE PAGES

    Maingi, R.; Hu, J. S.; Sun, Z.; ...

    2018-01-05

    Here, we report the first successful use of lithium (Li) to eliminate edge-localized modes (ELMs) with tungsten divertor plasma-facing components in the EAST device. Li powder injected into the scrape-off layer of the tungsten upper divertor successfully eliminated ELMs for 3–5 s in EAST. The ELM elimination became progressively more effective in consecutive discharges at constant lithium delivery rates, and the divertor D α baseline emission was reduced, both signatures of improved wall conditioning. A modest decrease in stored energy and normalized energy confinement was also observed, but the confinement relative to H98 remained well above 1, extending the previousmore » ELM elimination results via Li injection into the lower carbon divertor in EAST. These results can be compared with recent observations with lithium pellets in ASDEX-Upgrade that failed to mitigate ELMs, highlighting one comparative advantage of continuous powder injection for real-time ELM elimination.« less

  11. ELM elimination with Li powder injection in EAST discharges using the tungsten upper divertor

    NASA Astrophysics Data System (ADS)

    Maingi, R.; Hu, J. S.; Sun, Z.; Tritz, K.; Zuo, G. Z.; Xu, W.; Huang, M.; Meng, X. C.; Canik, J. M.; Diallo, A.; Lunsford, R.; Mansfield, D. K.; Osborne, T. H.; Gong, X. Z.; Wang, Y. F.; Li, Y. Y.; EAST Team

    2018-02-01

    We report the first successful use of lithium (Li) to eliminate edge-localized modes (ELMs) with tungsten divertor plasma-facing components in the EAST device. Li powder injected into the scrape-off layer of the tungsten upper divertor successfully eliminated ELMs for 3-5 s in EAST. The ELM elimination became progressively more effective in consecutive discharges at constant lithium delivery rates, and the divertor D α baseline emission was reduced, both signatures of improved wall conditioning. A modest decrease in stored energy and normalized energy confinement was also observed, but the confinement relative to H98 remained well above 1, extending the previous ELM elimination results via Li injection into the lower carbon divertor in EAST (Hu et al 2015 Phys. Rev. Lett. 114 055001). These results can be compared with recent observations with lithium pellets in ASDEX-Upgrade that failed to mitigate ELMs (Lang et al 2017 Nucl. Fusion 57 016030), highlighting one comparative advantage of continuous powder injection for real-time ELM elimination.

  12. ELM elimination with Li powder injection in EAST discharges using the tungsten upper divertor

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Maingi, R.; Hu, J. S.; Sun, Z.

    Here, we report the first successful use of lithium (Li) to eliminate edge-localized modes (ELMs) with tungsten divertor plasma-facing components in the EAST device. Li powder injected into the scrape-off layer of the tungsten upper divertor successfully eliminated ELMs for 3–5 s in EAST. The ELM elimination became progressively more effective in consecutive discharges at constant lithium delivery rates, and the divertor D α baseline emission was reduced, both signatures of improved wall conditioning. A modest decrease in stored energy and normalized energy confinement was also observed, but the confinement relative to H98 remained well above 1, extending the previousmore » ELM elimination results via Li injection into the lower carbon divertor in EAST. These results can be compared with recent observations with lithium pellets in ASDEX-Upgrade that failed to mitigate ELMs, highlighting one comparative advantage of continuous powder injection for real-time ELM elimination.« less

  13. Applying Cost-Sensitive Extreme Learning Machine and Dissimilarity Integration to Gene Expression Data Classification.

    PubMed

    Liu, Yanqiu; Lu, Huijuan; Yan, Ke; Xia, Haixia; An, Chunlin

    2016-01-01

    Embedding cost-sensitive factors into the classifiers increases the classification stability and reduces the classification costs for classifying high-scale, redundant, and imbalanced datasets, such as the gene expression data. In this study, we extend our previous work, that is, Dissimilar ELM (D-ELM), by introducing misclassification costs into the classifier. We name the proposed algorithm as the cost-sensitive D-ELM (CS-D-ELM). Furthermore, we embed rejection cost into the CS-D-ELM to increase the classification stability of the proposed algorithm. Experimental results show that the rejection cost embedded CS-D-ELM algorithm effectively reduces the average and overall cost of the classification process, while the classification accuracy still remains competitive. The proposed method can be extended to classification problems of other redundant and imbalanced data.

  14. Progress on the application of ELM control schemes to ITER scenarios from the non-active phase to DT operation

    NASA Astrophysics Data System (ADS)

    Loarte, A.; Huijsmans, G.; Futatani, S.; Baylor, L. R.; Evans, T. E.; Orlov, D. M.; Schmitz, O.; Becoulet, M.; Cahyna, P.; Gribov, Y.; Kavin, A.; Sashala Naik, A.; Campbell, D. J.; Casper, T.; Daly, E.; Frerichs, H.; Kischner, A.; Laengner, R.; Lisgo, S.; Pitts, R. A.; Saibene, G.; Wingen, A.

    2014-03-01

    Progress in the definition of the requirements for edge localized mode (ELM) control and the application of ELM control methods both for high fusion performance DT operation and non-active low-current operation in ITER is described. Evaluation of the power fluxes for low plasma current H-modes in ITER shows that uncontrolled ELMs will not lead to damage to the tungsten (W) divertor target, unlike for high-current H-modes in which divertor damage by uncontrolled ELMs is expected. Despite the lack of divertor damage at lower currents, ELM control is found to be required in ITER under these conditions to prevent an excessive contamination of the plasma by W, which could eventually lead to an increased disruptivity. Modelling with the non-linear MHD code JOREK of the physics processes determining the flow of energy from the confined plasma onto the plasma-facing components during ELMs at the ITER scale shows that the relative contribution of conductive and convective losses is intrinsically linked to the magnitude of the ELM energy loss. Modelling of the triggering of ELMs by pellet injection for DIII-D and ITER has identified the minimum pellet size required to trigger ELMs and, from this, the required fuel throughput for the application of this technique to ITER is evaluated and shown to be compatible with the installed fuelling and tritium re-processing capabilities in ITER. The evaluation of the capabilities of the ELM control coil system in ITER for ELM suppression is carried out (in the vacuum approximation) and found to have a factor of ˜2 margin in terms of coil current to achieve its design criterion, although such a margin could be substantially reduced when plasma shielding effects are taken into account. The consequences for the spatial distribution of the power fluxes at the divertor of ELM control by three-dimensional (3D) fields are evaluated and found to lead to substantial toroidal asymmetries in zones of the divertor target away from the separatrix. Therefore, specifications for the rotation of the 3D perturbation applied for ELM control in order to avoid excessive localized erosion of the ITER divertor target are derived. It is shown that a rotation frequency in excess of 1 Hz for the whole toroidally asymmetric divertor power flux pattern is required (corresponding to n Hz frequency in the variation of currents in the coils, where n is the toroidal symmetry of the perturbation applied) in order to avoid unacceptable thermal cycling of the divertor target for the highest power fluxes and worst toroidal power flux asymmetries expected. The possible use of the in-vessel vertical stability coils for ELM control as a back-up to the main ELM control systems in ITER is described and the feasibility of its application to control ELMs in low plasma current H-modes, foreseen for initial ITER operation, is evaluated and found to be viable for plasma currents up to 5-10 MA depending on modelling assumptions.

  15. Development of Japanese experiment module remote manipulator system

    NASA Technical Reports Server (NTRS)

    Matsueda, Tatsuo; Kuwao, Fumihiro; Motohasi, Shoichi; Okamura, Ryo

    1994-01-01

    National Space Development Agency of Japan (NASDA) is developing the Japanese Experiment Module (JEM), as its contribution to the International Space Station. The JEM consists of the pressurized module (PM), the exposed facility (EF), the experiment logistics module pressurized section (ELM-PS), the experiment logistics module exposed section (ELM-ES) and the Remote Manipulator System (RMS). The JEMRMS services for the JEM EF, which is a space experiment platform, consists of the Main Arm (MA), the Small Fine Arm (SFA) and the RMS console. The MA handles the JEM EF payloads, the SFA and the JEM element, such as ELM-ES.

  16. Replication fork reversal triggers fork degradation in BRCA2-defective cells.

    PubMed

    Mijic, Sofija; Zellweger, Ralph; Chappidi, Nagaraja; Berti, Matteo; Jacobs, Kurt; Mutreja, Karun; Ursich, Sebastian; Ray Chaudhuri, Arnab; Nussenzweig, Andre; Janscak, Pavel; Lopes, Massimo

    2017-10-16

    Besides its role in homologous recombination, the tumor suppressor BRCA2 protects stalled replication forks from nucleolytic degradation. Defective fork stability contributes to chemotherapeutic sensitivity of BRCA2-defective tumors by yet-elusive mechanisms. Using DNA fiber spreading and direct visualization of replication intermediates, we report that reversed replication forks are entry points for fork degradation in BRCA2-defective cells. Besides MRE11 and PTIP, we show that RAD52 promotes stalled fork degradation and chromosomal breakage in BRCA2-defective cells. Inactivation of these factors restores reversed fork frequency and chromosome integrity in BRCA2-defective cells. Conversely, impairing fork reversal prevents fork degradation, but increases chromosomal breakage, uncoupling fork protection, and chromosome stability. We propose that BRCA2 is dispensable for RAD51-mediated fork reversal, but assembles stable RAD51 nucleofilaments on regressed arms, to protect them from degradation. Our data uncover the physiopathological relevance of fork reversal and illuminate a complex interplay of homologous recombination factors in fork remodeling and stability.BRCA2 is involved in both homologous recombination (HR) and the protection of stalled replication forks from degradation. Here the authors reveal how HR factors cooperate in fork remodeling, showing that BRCA2 supports RAD51 loading on the regressed arms of reversed replication forks to protect them from degradation.

  17. Slippery Elm

    MedlinePlus

    Slippery elm is a tree that is native to eastern Canada and the eastern and central United States. ... whole bark) is used as medicine. People take slippery elm by mouth for coughs, sore throat, colic, diarrhea, ...

  18. Discriminant analysis to predict the occurrence of ELMS in H-mode discharges

    NASA Astrophysics Data System (ADS)

    Kardaun, O. J. W. F.; Itoh, S.-I.; Itoh, K.; Kardaun, J. W. P. F.

    1993-08-01

    After an exposition of its theoretical background, discriminant analysis is applied to the H-mode confinement database to find the region in plasma parameter space in which H-mode with small ELM's (Edge Localized Modes) is likely to occur. The boundary of this region is determined by the condition that the probability of appearance of such a type of H-mode, as a function of the plasma parameters, should be larger than some threshold value and larger than the corresponding probability for other types of H-mode (i.e., H-mode without ELM's or with giant ELM's). In practice, the discrimination has been performed for the ASDEX, JET and JFT-2M tokamaks using four instantaneous plasma parameters (injected power Pinj, magnetic field Bt, plasma current Ip and line averaged electron density ne) and taking also memory effects of the plasma and the distance between the plasma and the wall into account, while using variables that are normalized with respect to machine size. Generally speaking, it is found that there is a substantial overlap between the region of H-mode with small ELM's and the region of the two other types of H-mode. However, the ELM-free and the giant ELM H-modes relatively rarely appear in the region, that, according to the analysis, is allocated to small ELM's. A reliable production of H-mode with only small ELM's seems well possible by choosing this regime in parameter space. In the present study, it was not attempted to arrive at a unified discrimination across the machines. So, projection from one machine to another remains difficult, and a reliable determination of the region where small ELM's occur still requires a training sample from the device under consideration.

  19. Herpetological monitoring and assessment on the Trinity River, Trinity County, California—Final report

    USGS Publications Warehouse

    Snover, Melissa L.; Adams, Michael J.

    2016-06-14

    The primary goal of the Trinity River Restoration Program is to rehabilitate the fisheries on the dam-controlled Trinity River. However, maintaining and enhancing other wildlife populations through the restoration initiative is also a key objective. Foothill yellow-legged frogs (Rana boylii) and western pond turtles (Actinemys marmorata) have been identified as important herpetological species on which to focus monitoring efforts due to their status as California state-listed species of concern and potential listing on the U.S. Endangered Species List. We developed and implemented a monitoring strategy for these species specific to the Trinity River with the objectives of establishing baseline values for probabilities of site occupancy, colonization, and local extinction; identifying site characteristics that correlate with the probability of extinction; and estimating overall trends in abundance. Our 3-year study suggests that foothill yellow-legged frogs declined in the probability of site occupancy. Conversely, our results suggest that western pond turtles increased in both abundance and the probability of site occupancy. The short length of our study period makes it difficult to draw firm conclusions, but these results provide much-needed baseline data. Further monitoring and directed studies are required to assess how habitat changes and management decisions relate to the status and trend of these species over the long term.

  20. 77 FR 50668 - Proposed Flood Elevation Determinations

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-22

    ... County, Texas, and Incorporated Areas. Specifically, it addresses the flooding sources: Black Fork Creek, Black Fork Creek Tributary BF-1, Black Fork Creek Tributary BF-M-1, Black Fork Creek Tributary D, Black Fork Creek Tributary D-1, Black Fork Creek Tributary D-2, Black Fork Creek Tributary D-3, Butler Creek...

  1. Spatial-spectral blood cell classification with microscopic hyperspectral imagery

    NASA Astrophysics Data System (ADS)

    Ran, Qiong; Chang, Lan; Li, Wei; Xu, Xiaofeng

    2017-10-01

    Microscopic hyperspectral images provide a new way for blood cell examination. The hyperspectral imagery can greatly facilitate the classification of different blood cells. In this paper, the microscopic hyperspectral images are acquired by connecting the microscope and the hyperspectral imager, and then tested for blood cell classification. For combined use of the spectral and spatial information provided by hyperspectral images, a spatial-spectral classification method is improved from the classical extreme learning machine (ELM) by integrating spatial context into the image classification task with Markov random field (MRF) model. Comparisons are done among ELM, ELM-MRF, support vector machines(SVM) and SVMMRF methods. Results show the spatial-spectral classification methods(ELM-MRF, SVM-MRF) perform better than pixel-based methods(ELM, SVM), and the proposed ELM-MRF has higher precision and show more accurate location of cells.

  2. Energetic ion losses caused by magnetohydrodynamic activity resonant and non-resonant with energetic ions in Large Helical Device

    NASA Astrophysics Data System (ADS)

    Ogawa, Kunihiro; Isobe, Mitsutaka; Toi, Kazuo; Shimizu, Akihiro; Spong, Donald A.; Osakabe, Masaki; Yamamoto, Satoshi; the LHD Experiment Group

    2014-09-01

    Experiments to reveal energetic ion dynamics associated with magnetohydrodynamic activity are ongoing in the Large Helical Device (LHD). Interactions between beam-driven toroidal Alfvén eigenmodes (TAEs) and energetic ions have been investigated. Energetic ion losses induced by beam-driven burst TAEs have been observed using a scintillator-based lost fast-ion probe (SLIP) in neutral beam-heated high β plasmas. The loss flux of co-going beam ions increases as the TAE amplitude increases. In addition to this, the expulsion of beam ions associated with edge-localized modes (ELMs) has been also recognized in LHD. The SLIP has indicated that beam ions having co-going and barely co-going orbits are affected by ELMs. The relation between ELM amplitude and ELM-induced loss has a dispersed structure. To understand the energetic ion loss process, a numerical simulation based on an orbit-following model, DELTA5D, that incorporates magnetic fluctuations is performed. The calculation result shows that energetic ions confined in the interior region are lost due to TAE instability, with a diffusive process characterizing their loss. For the ELM, energetic ions existing near the confinement/loss boundary are lost through a convective process. We found that the ELM-induced loss flux measured by SLIP changes with the ELM phase. This relation between the ELM amplitude and measured ELM-induced loss results in a more dispersed loss structure.

  3. Endangered Species Management Plan for Fort Hood, Texas: FY06-10

    DTIC Science & Technology

    2007-05-01

    Texas red oak, post oak, Texas ash (Fraxinus texensis), shin oak, blackjack oak (Quercus marilandica), slippery elm (Ulmus rubra), cedar elm ...by Ashe juniper and Texas oak. Other important tree species included live oak, cedar elm (Ulmus crassifolia), Lacey oak (Quercus laceyi), Arizona...0.83 m (Cimprich 2005). Nest substrates include shin oak, Texas red oak, Texas redbud, Ashe juniper, Texas ash, Plateau live oak, cedar elm , rusty

  4. The banded elm bark beetle: A new threat to elms in North America

    Treesearch

    Jose F. Negron; Jeffrey J. Witcosky; Robert J. Cain; James R. LaBonte; Donald A. Duerr; Sally J. McElwey; Jana C. Lee; Steven J. Seybold

    2005-01-01

    An exotic bark beetle from Asia, the banded elm bark beetle, Scolytus schevyrewi, has been discovered in 21 states of the United States. Although its point of entry is not known, a survey of museum specimens suggests that it has been in the US for at least 10 years. It is most abundant in western states, attacks primarily American and Siberian elms, and carries spores...

  5. The relationships between edge localized modes suppression, pedestal profiles and lithium wall coatings in NSTX

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Boyle, D. P.; Maingi, R.; Snyder, P. B.

    2011-01-01

    Recently in the National Spherical Torus Experiment (NSTX), increasing lithium wall coatings suppressed edge localized modes (ELMs), gradually but not quite monotonically. This work details profile and stability analysis as ELMs disappeared throughout the lithium scan. While the quantity of lithium deposited between discharges did not uniquely determine the presence of ELMs, profile analysis demonstrated that lithium was correlated with wider density and pressure pedestals with peak gradients farther from the separatrix. Moreover, the ELMy and ELM-free discharges were cleanly separated by their density and pedestal widths and peak gradient locations. Ultimately, ELMs were only suppressed when lithium caused themore » density pedestal to widen and shift inward. These changes in the density gradient were directly reflected in the pressure gradient and calculated bootstrap current. This supports the theory that ELMs in NSTX are caused by peeling and/or ballooning modes, as kink/peeling modes are stabilized when the edge current and pressure gradient shift away from the separatrix. Edge stability analysis using ELITE corroborated this picture, as reconstructed equilibria from ELM-free discharges were generally farther from their kink/peeling stability boundaries than ELMy discharges. We conclude that density profile control provided by lithium is the key first step to ELM suppression in NSTX.« less

  6. A comparative analysis of support vector machines and extreme learning machines.

    PubMed

    Liu, Xueyi; Gao, Chuanhou; Li, Ping

    2012-09-01

    The theory of extreme learning machines (ELMs) has recently become increasingly popular. As a new learning algorithm for single-hidden-layer feed-forward neural networks, an ELM offers the advantages of low computational cost, good generalization ability, and ease of implementation. Hence the comparison and model selection between ELMs and other kinds of state-of-the-art machine learning approaches has become significant and has attracted many research efforts. This paper performs a comparative analysis of the basic ELMs and support vector machines (SVMs) from two viewpoints that are different from previous works: one is the Vapnik-Chervonenkis (VC) dimension, and the other is their performance under different training sample sizes. It is shown that the VC dimension of an ELM is equal to the number of hidden nodes of the ELM with probability one. Additionally, their generalization ability and computational complexity are exhibited with changing training sample size. ELMs have weaker generalization ability than SVMs for small sample but can generalize as well as SVMs for large sample. Remarkably, great superiority in computational speed especially for large-scale sample problems is found in ELMs. The results obtained can provide insight into the essential relationship between them, and can also serve as complementary knowledge for their past experimental and theoretical comparisons. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. 3. View of Clark Fork Vehicle Bridge facing southwest. Bridge ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. View of Clark Fork Vehicle Bridge facing southwest. Bridge from north shore of Clark Fork River. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  8. Parameter dependence of ELM loss reduction by magnetic perturbations at low pedestal density and collisionality in ASDEX upgrade

    NASA Astrophysics Data System (ADS)

    Leuthold, N.; Suttrop, W.; Fischer, R.; Kappatou, A.; Kirk, A.; McDermott, R.; Mlynek, A.; Valovič, M.; Willensdorfer, M.; the ASDEX Upgrade Team; the EUROfusion MST1 Team

    2017-05-01

    ELM mitigation by magnetic perturbations is studied at low pedestal collisionalities down to ITER-like values ({ν }{e,{PED}}* =0.1) in ASDEX Upgrade. A comprehensive database of ELM energy losses for varying plasma density, heating power, edge safety factor and magnetic perturbation structure has been assembled to investigate parameter dependencies of ELM mitigation. It is found that magnetic perturbations with a toroidal mode number n = 2 can reduce the ELM energy loss normalized to the energy stored in the plasma pedestal from about 30% to less than 5%, i.e. by a factor of six, below an electron pedestal collisionality of {ν }{e,{PED}}* =0.4. At this level of ELM mitigation a significant reduction of the pedestal pressure and, therefore, global plasma confinement occurs. This pedestal pressure reduction is mostly due to a reduction of plasma density, the so-called ‘pump-out’ effect. Refueling by neutral beams and in particular by pellet injection is possible and can re-establish confinement, however, the ELM energy loss increases as well with increasing density.

  9. 4. View of Clark Fork Vehicle Bridge facing northeast. Bridge ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. View of Clark Fork Vehicle Bridge facing northeast. Bridge from south shoreof Clark Fork River showing 4 spans. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  10. Urban Town and Gown: Increasing Minority Participation in the Geosciences Through a College-High School Partnership in Hartford, CT

    NASA Astrophysics Data System (ADS)

    OConnell, S.; OConnell, S.; OConnell, S.; Osborn, J. L.; Osborn, J. L.

    2001-12-01

    Urban public schools are often poor and have a tremendous need for educational assistance. In many cities the population is dominated by ethnic minorities. Hartford, CT, is one of these cities. Only about 50% of the students entering high school graduate and approximately 50% of those go on to higher education. Of those students taking the SAT's the average verbal and math scores are below 400. Despite these statistics, many students do succeed and therein lies an opportunity for earth scientists. As individuals and as institutions we can partner with schools and students to involve them in and excite them about the earth sciences. In 1995 Trinity College, located in Hartford, CT, undertook a \\$175 m.d. neighborhood revitalization project with funds from the college, neighboring institutions, foundations, and city, state and federal governments. Central to the revitalization is the "Learning Corridor," an educational complex that includes a magnet Montessori School, a Math and Science Middle School, and a Math and Science Magnet High School (GHAMAS). GHAMAS has a three-fold mission: teaching math and science to high school students, professional development for all math and science teachers from participating school districts, and community outreach. The Learning Corridor is adjacent to the Trinity College campus and Trinity faculty work with GHAMAS faculty to fulfill all three missions. Trinity faculty teach several high school classes. During the summer 3 Trinity and 1 GHAMAS faculty participated as a group in a week long-long NSF-sponsored Environmental Science workshop. This fall over ten teacher workshops were co-taught by Trinity and GHAMAS faculty. Recent NSF funding will allow us to develop a collaborative education and research program focused on the Connecticut River.

  11. Lower Mississippi River Environmental Program. Report 2. A Physical Description of Main Stem Levee Borrow Pits along the Lower Mississippi River

    DTIC Science & Technology

    1988-02-01

    Eastern cottonwood, green ash, sugarberry. box elder, bald cypress, willow honey locust, slippery elm , overcup oak and bitter pecan. Principle...vines and understory. Woody vegetation surrounds the borrow pit and consists of American and slippery elms , silver maple, black willow, cottonwood, pin...aquatica Water elm Ulmus rubra Slippery elm Urtica dioica Stinging nettle Vaccinium sp. Blueberry Vaccinium spp. Vaccinum Vernonia altissima Ironweed

  12. Water Resources Development Miami River, Little Miami River, and Mill Creek Basins, Southwest Ohio. Volume 2. Appendices A-G.

    DTIC Science & Technology

    1981-10-01

    the area. Common species include boxelder, black locust, hackberry, tree of heaven, sycamore, Osage orange, black willow, mulberry, slippery elm ...and maple include tulip poplar, white ash, red elm , American elm , black cherry, hackberry, walnut, basswood, buckeye, white oak, shagbark hickory, and...willow. Other canopy species in these communities include buckeye, elm , beech, black locust, hackberry, walnut, and silver maple. The most prevalent

  13. Time and materials needed to survey, inject systemic fungicides, and install root-graft barriers for Dutch elm disease management

    Treesearch

    William N., Jr. Cannon; Jack H. Barger; Charles J. Kostichka; Charles J. Kostichka

    1986-01-01

    Dutch elm disease control practice in 15 communities showed a wide range of time and material required to apply control methods. The median time used for each method was: sanitation survey, 9.8 hours per square mile; symptom survey, 96 hours per thousand elms; systemic fungicide injection, 1.4 hours per elm; and root-graft barrier installation, 2.2 hours per barrier (5...

  14. Dynamic extreme learning machine and its approximation capability.

    PubMed

    Zhang, Rui; Lan, Yuan; Huang, Guang-Bin; Xu, Zong-Ben; Soh, Yeng Chai

    2013-12-01

    Extreme learning machines (ELMs) have been proposed for generalized single-hidden-layer feedforward networks which need not be neuron alike and perform well in both regression and classification applications. The problem of determining the suitable network architectures is recognized to be crucial in the successful application of ELMs. This paper first proposes a dynamic ELM (D-ELM) where the hidden nodes can be recruited or deleted dynamically according to their significance to network performance, so that not only the parameters can be adjusted but also the architecture can be self-adapted simultaneously. Then, this paper proves in theory that such D-ELM using Lebesgue p-integrable hidden activation functions can approximate any Lebesgue p-integrable function on a compact input set. Simulation results obtained over various test problems demonstrate and verify that the proposed D-ELM does a good job reducing the network size while preserving good generalization performance.

  15. Characteristics of the Secondary Divertor on DIII-D

    NASA Astrophysics Data System (ADS)

    Watkins, J. G.; Lasnier, C. J.; Leonard, A. W.; Evans, T. E.; Pitts, R.; Stangeby, P. C.; Boedo, J. A.; Moyer, R. A.; Rudakov, D. L.

    2009-11-01

    In order to address a concern that the ITER secondary divertor strike plates may be insufficiently robust to handle the incident pulses of particles and energy from ELMs, we performed dedicated studies of the secondary divertor plasma and scrape-off layer (SOL). Detailed measurements of the ELM energy and particle deposition footprint on the secondary divertor target plates were made with a fast IR camera and Langmuir probes and SOL profile and transport measurements were made with reciprocating probes. The secondary divertor and SOL conditions depended on changes in the magnetic balance and the core plasma density. Larger density resulted in smaller ELMs and the magnetic balance affected how many ELM particles coupled to the secondary SOL and divertor. Particularly striking are the images from a new fast IR camera that resolve ELM heat pulses and show spiral patterns with multiple peaks during ELMs in the secondary divertor.

  16. 2. View of Clark Fork Vehicle Bridge facing northeast. Bridge ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. View of Clark Fork Vehicle Bridge facing northeast. Bridge from south shore of Clark Fork River showing 4 1/2 spans. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  17. 7. View of Clark Fork Vehicle Bridge facing northwest. Bridge ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. View of Clark Fork Vehicle Bridge facing northwest. Bridge from south shore of Clark Fork River showing 4 1/2 spans. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  18. Evaluation of median barrier safety issues.

    DOT National Transportation Integrated Search

    2008-01-01

    The objective of this study was to evaluate the effectiveness of the Brifen TL-4 and Trinity CASS median cable barrier systems in preventing cross-median collisions on sections of I-64, I-71, and I-265 (Brifen system) and I-265 (Trinity system) in Je...

  19. Analysis of Trinity Power Metrics for Automated Monitoring

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Michalenko, Ashley Christine

    This is a presentation from Los Alamos National Laboraotyr (LANL) about the analysis of trinity power metrics for automated monitoring. The following topics are covered: current monitoring efforts, motivation for analysis, tools used, the methodology, work performed during the summer, and future work planned.

  20. Ephemeral magma chambers in the Trinity peridotite, northern California

    NASA Astrophysics Data System (ADS)

    Cannat, Mathilde; Lécuyer, Christophe

    1991-02-01

    The Trinity Massif comprises the major lithologies of an ophiolite, as defined at the 1972 Penrose conference. Previous studies have shown, however, that it differs from the Semail (Oman) or Table Mountain (Newfoundland) ophiolitic massifs, particularly because its crustal section is thin, and because its mantle section has vertical plastic flow planes. These features have led to an interpretation of the Trinity Massif as a fragment of slow-spreading oceanic lithosphere (Le Sueur et al., 1984; Boudier and Nicolas, 1985). In this paper, we show that the Trinity gabbros occur in discontinuous, kilometre-sized pockets, intrusive into the mantle peridotites. The internal stratigraphy and the petrological characteristics of these gabbros suggest that they formed in short-lived magma chambers. These ephemeral magma chambers developed after the end of the plastic deformation in the surrounding mantle, when it had cooled down to lithospheric temperatures. We discuss the possibility that these small and ephemeral magma chambers formed at a slow-spreading oceanic ridge.

  1. Measurements of extinct fission products in nuclear bomb debris: Determination of the yield of the Trinity nuclear test 70 y later

    DOE PAGES

    Hanson, Susan Kloek; Pollington, Anthony Douglas; Waidmann, Christopher Russell; ...

    2016-07-05

    This study describes an approach to measuring extinct fission products that would allow for the characterization of a nuclear test at any time. The isotopic composition of molybdenum in five samples of glassy debris from the 1945 Trinity nuclear test has been measured. Nonnatural molybdenum isotopic compositions were observed, reflecting an input from the decay of the short-lived fission products 95Zr and 97Zr. By measuring both the perturbation of the 95Mo/ 96Mo and 97Mo/ 96Mo isotopic ratios and the total amount of molybdenum in the Trinity nuclear debris samples, it is possible to calculate the original concentrations of the 95Zrmore » and 97Zr isotopes formed in the nuclear detonation. Together with a determination of the amount of plutonium in the debris, these measurements of extinct fission products allow for new estimates of the efficiency and yield of the historic Trinity test.« less

  2. Measurements of extinct fission products in nuclear bomb debris: Determination of the yield of the Trinity nuclear test 70 y later

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hanson, Susan Kloek; Pollington, Anthony Douglas; Waidmann, Christopher Russell

    This study describes an approach to measuring extinct fission products that would allow for the characterization of a nuclear test at any time. The isotopic composition of molybdenum in five samples of glassy debris from the 1945 Trinity nuclear test has been measured. Nonnatural molybdenum isotopic compositions were observed, reflecting an input from the decay of the short-lived fission products 95Zr and 97Zr. By measuring both the perturbation of the 95Mo/ 96Mo and 97Mo/ 96Mo isotopic ratios and the total amount of molybdenum in the Trinity nuclear debris samples, it is possible to calculate the original concentrations of the 95Zrmore » and 97Zr isotopes formed in the nuclear detonation. Together with a determination of the amount of plutonium in the debris, these measurements of extinct fission products allow for new estimates of the efficiency and yield of the historic Trinity test.« less

  3. Simulation of groundwater flow in the Edwards-Trinity and related aquifers in the Pecos County region, Texas

    USGS Publications Warehouse

    Thomas, Jonathan V.

    2014-01-01

    The Edwards-Trinity aquifer, a major aquifer in the Pecos County region of western Texas, is a vital groundwater resource for agricultural, industrial, and public supply uses. Resource managers would like to better understand the future availability of water in the Edwards-Trinity aquifer in the Pecos County region and the effects of the possible increase or temporal redistribution of groundwater withdrawals. To that end, the U.S. Geological Survey (USGS), in cooperation with the Middle Pecos Groundwater Conservation District, Pecos County, City of Fort Stockton, Brewster County, and Pecos County Water Control and Improvement District No. 1, completed a comprehensive, integrated analysis of available hydrogeologic data to develop a groundwater-flow model of the Edwards-Trinity and related aquifers in parts of Brewster, Jeff Davis, Pecos, and Reeves Counties. Following calibration, the model was used to evaluate the sustainability of recent (2008) and projected water-use demands on groundwater resources in the study area.

  4. Measurements of extinct fission products in nuclear bomb debris: Determination of the yield of the Trinity nuclear test 70 y later

    PubMed Central

    Hanson, Susan K.; Pollington, Anthony D.; Waidmann, Christopher R.; Kinman, William S.; Wende, Allison M.; Miller, Jeffrey L.; Berger, Jennifer A.; Oldham, Warren J.; Selby, Hugh D.

    2016-01-01

    This paper describes an approach to measuring extinct fission products that would allow for the characterization of a nuclear test at any time. The isotopic composition of molybdenum in five samples of glassy debris from the 1945 Trinity nuclear test has been measured. Nonnatural molybdenum isotopic compositions were observed, reflecting an input from the decay of the short-lived fission products 95Zr and 97Zr. By measuring both the perturbation of the 95Mo/96Mo and 97Mo/96Mo isotopic ratios and the total amount of molybdenum in the Trinity nuclear debris samples, it is possible to calculate the original concentrations of the 95Zr and 97Zr isotopes formed in the nuclear detonation. Together with a determination of the amount of plutonium in the debris, these measurements of extinct fission products allow for new estimates of the efficiency and yield of the historic Trinity test. PMID:27382169

  5. De novo transcript sequence reconstruction from RNA-seq using the Trinity platform for reference generation and analysis.

    PubMed

    Haas, Brian J; Papanicolaou, Alexie; Yassour, Moran; Grabherr, Manfred; Blood, Philip D; Bowden, Joshua; Couger, Matthew Brian; Eccles, David; Li, Bo; Lieber, Matthias; MacManes, Matthew D; Ott, Michael; Orvis, Joshua; Pochet, Nathalie; Strozzi, Francesco; Weeks, Nathan; Westerman, Rick; William, Thomas; Dewey, Colin N; Henschel, Robert; LeDuc, Richard D; Friedman, Nir; Regev, Aviv

    2013-08-01

    De novo assembly of RNA-seq data enables researchers to study transcriptomes without the need for a genome sequence; this approach can be usefully applied, for instance, in research on 'non-model organisms' of ecological and evolutionary importance, cancer samples or the microbiome. In this protocol we describe the use of the Trinity platform for de novo transcriptome assembly from RNA-seq data in non-model organisms. We also present Trinity-supported companion utilities for downstream applications, including RSEM for transcript abundance estimation, R/Bioconductor packages for identifying differentially expressed transcripts across samples and approaches to identify protein-coding genes. In the procedure, we provide a workflow for genome-independent transcriptome analysis leveraging the Trinity platform. The software, documentation and demonstrations are freely available from http://trinityrnaseq.sourceforge.net. The run time of this protocol is highly dependent on the size and complexity of data to be analyzed. The example data set analyzed in the procedure detailed herein can be processed in less than 5 h.

  6. Concordant paleolatitudes for Neoproterozoic ophiolitic rocks of the Trinity Complex, Klamath Mountains, California

    USGS Publications Warehouse

    Mankinen, E.A.; Lindsley-Griffin, N.; Griffin, J.R.

    2002-01-01

    New paleomagnetic results from the eastern Klamath Mountains of northern California show that Neoproterozoic rocks of the Trinity ophiolitic complex and overlying Middle Devonian volcanic rocks are latitudinally concordant with cratonal North America. Combining paleomagnetic data with regional geologic and faunal evidence suggests that the Trinity Complex and related terranes of the eastern Klamath plate were linked in some fashion to the North American craton throughout that time, but that distance between them may have varied considerably. A possible model that is consistent with our paleomagnetic results and the geologic evidence is that the Trinity Complex formed and migrated parallel to paleolatitude in the basin between Laurasia and Australia-East Antarctica as the Rodinian supercontinent began to break up. It then continued to move parallel to paleolatitude at least through Middle Devonian time. Although the eastern Klamath plate served as a nucleus against which more western components of the Klamath Mountains province amalgamated, the Klamath superterrane was not accreted to North America until Early Cretaceous time.

  7. Circulating Elastin Fragments Are Not Affected by Hepatic, Renal and Hemodynamic Changes, But Reflect Survival in Cirrhosis with TIPS.

    PubMed

    Nielsen, M J; Lehmann, J; Leeming, D J; Schierwagen, R; Klein, S; Jansen, C; Strassburg, C P; Bendtsen, F; Møller, S; Sauerbruch, T; Karsdal, M A; Krag, A; Trebicka, J

    2015-11-01

    Progressive fibrosis increases hepatic resistance and causes portal hypertension with complications. During progressive fibrosis remodeling and deposition of collagens and elastin occur. Elastin remodeling is crucially involved in fibrosis progression in animal models and human data. This study investigated the association of circulating elastin with the clinical outcome in cirrhotic patients with severe portal hypertension receiving transjugular intrahepatic porto-systemic shunt (TIPS). We analyzed portal and hepatic venous samples of 110 cirrhotic patients obtained at TIPS insertion and 2 weeks later. The circulating levels of elastin fragments (ELM) were determined using specific monoclonal ELISA. The relationship of ELM with clinical short-time follow-up and long-term outcome was investigated. Circulating levels of ELM showed a gradient across the liver before TIPS with higher levels in the hepatic vein. Interestingly, the circulating ELM levels remained unchanged after TIPS. The circulating levels of ELM in portal and hepatic veins correlated with platelet counts and inversely with serum sodium. Hepatic venous levels of ELM were higher in CHILD C compared to CHILD A and B and were associated with the presence of ascites. Patients with high levels of ELM in the hepatic veins before TIPS showed poorer survival. In multivariate analysis ELM levels in the hepatic veins and MELD were independent predictors of mortality in these patients. This study demonstrated that circulating levels of ELM are not associated with hemodynamic changes, but might reflect fibrosis remodeling and predict survival in patients with severe portal hypertension receiving TIPS independently of MELD.

  8. First results from the US-PRC PMI collaboration on EAST

    NASA Astrophysics Data System (ADS)

    Maingi, R.; Lunsford, R.; Mansfield, D.; Diallo, A.; Hu, J.; Sun, Z.; Zuo, G.; Gong, X.; Tritz, K.; Canik, J.; Osborne, T.; EAST Team

    2017-10-01

    A US-PRC collaboration was formed to understand the plasma-material interface for improved long pulse discharge performance in EAST, with an emphasis on Li conditioning techniques. The US multi-institutional team consists of participants from PPPL, UI-UC, UT-K, ORNL, MIT, LANL, and JHU. In Dec. 2016, this team co-led experiments on the use of Li aerosol injection to mitigate ELMs, Li granule injection to pace ELMs, and a flowing liquid Li limiter to serve as a primary plasma-facing component. Li aerosol injection was shown to eliminate ELMs using the upper ITER-like W divertor, extending previous results of ELM suppression in the lower cabon divertor (J.S. Hu, PRL 2015). In addition Li granule injection was shown to trigger and even pace ELMs, although the paced ELM frequency was slower than the natural ELM frequency in this set of experiments; previously paced ELM frequency was comparable to natural ELMs frequency (D.K. Mansfield, NF 2013). Finally a second generation flowing liquid Li limiter was shown to be compatible with ELMy H-mode plasmas, pushed within 1 cm of the separatrix. The surface showed no damage to PMI and improved wetting as compared to the first generation limiter experiments (J.S. Hu, NF 2016 and G.Z. Zuo, NF 2017). US scientists supported in part by US DoE contracts DE-AC02-09CH11466, DE-FG02-09ER55012, DE-AC05-00OR22725, and DE-FC02-04ER54698, and ASIPP scientists by Contract No. 11625524, No. 11075185, No. 11021565, and No. 2013GB114004.

  9. Sr-Nd isotopes constrain on the deposit history of the basins in the Gulf of Mexico

    NASA Astrophysics Data System (ADS)

    Li, Y.; Jiang, S.

    2015-12-01

    The Brazos-Trinity Basin IV and Ursa Basin are situated on the northern slope of the Gulf of Mexico. The Ursa basin lies in the center of late Pleistocene Mississippi River deposition, received the sediment deposition during Marine Isotope Stage (MIS) 2- 4. The Brazos-Trinity Basin IV belongs to a part of the Brazos-Trinity fan, it recorded the turbidite deposition and hemiplegic deposition during MIS1- 5. The Sr and Nd isotopic composition of the detrital composition of the sediment in both basins indicates the change of the sediment provenance during the basin-filled process. In the Ursa basin, The difference of 87Sr/86Sr ratio and ɛNd of the detrital component between MIS1,2 (87Sr/86Sr ~ 0.7219 - 0.7321, ɛNd ~ -12 - -13.4) and MIS3,4(87Sr/86Sr ~ 0.7310 - 0.7354, ɛNd ~ -16 - -17.9) is suggested to be related with the provenance change of the detrital particles since LGM. The addition of detrital particle from Appalachians with less radiogenic 87Sr/86Sr and positive ɛNd altered the character of the sediment of the Mississippi River during the last glaciation and deglaciation. In the Brazos-Trinity Basin IV, the narrow range of 87Sr/86Sr and ɛNd indicate that the sediment source of Brazos-Trinity Basin IV had not changed obviously during MIS5e to MIS2, mostly from coastal rivers such as Brazos River, Trinity River and Sabine River. The pre-fan with 87Sr/86Sr ~0.735 and ɛNd ~ -14.5 to -16.9, which is very similar to the deep sediment in the Ursa Basin with 87Sr/86Sr ~0.733 to 0.735 and ɛNd ~ -16 to -18. It is suggested that sediments of the pre-fan of the Brazos-Trinity Basin IV were supplied from the ancestral Mississippi River Delta during the low sea level (MIS 6). During the MIS5, the discharge of Mississippi River is thought switched to its present course, ~300 km to the east.

  10. 1. View of Clark Fork Vehicle Bridge facing west. Panorama ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. View of Clark Fork Vehicle Bridge facing west. Panorama showing the entire span of bridge from north shore of the Clark Fork River. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  11. An Improved Iris Recognition Algorithm Based on Hybrid Feature and ELM

    NASA Astrophysics Data System (ADS)

    Wang, Juan

    2018-03-01

    The iris image is easily polluted by noise and uneven light. This paper proposed an improved extreme learning machine (ELM) based iris recognition algorithm with hybrid feature. 2D-Gabor filters and GLCM is employed to generate a multi-granularity hybrid feature vector. 2D-Gabor filter and GLCM feature work for capturing low-intermediate frequency and high frequency texture information, respectively. Finally, we utilize extreme learning machine for iris recognition. Experimental results reveal our proposed ELM based multi-granularity iris recognition algorithm (ELM-MGIR) has higher accuracy of 99.86%, and lower EER of 0.12% under the premise of real-time performance. The proposed ELM-MGIR algorithm outperforms other mainstream iris recognition algorithms.

  12. 5. View of Clark Fork Vehicle Bridge facing east. Bridge ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. View of Clark Fork Vehicle Bridge facing east. Bridge from south shore of Clark Fork River-southernmost span. 1900-era Northern Pacific Railway Bridge in background. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  13. Lower Mississippi River Environmental Program. Report 3. Bird and Mammal Use of Main Stem Levee Borrow Pits Along the Lower Mississippi River.

    DTIC Science & Technology

    1986-02-01

    overcup oak, tupelo gum, Nuttall oak, American elm , slippery elm , i , hickories, persimmon, silver maple, deciduous holly, swamp privet, and rose mallows...cottonwood, green ash, sugarberry, box elder, deciduous holly, osage orange, swamp privet, hickories, overcup oak, water locust, honey locust, slippery elm ...wood, box elder, osage orange, hickories, honey locust, water locust, slippery elm , swamp privet, sugarberry, persimmon, and rose mallows. Where

  14. Characterizing Tungsten Sourcing and SOL Transport during the Metal Rings Campaign

    NASA Astrophysics Data System (ADS)

    Thomas, D. M.; Abrams, T.; Unterberg, E. A.; Donovan, D.; Elder, J. D.; Wampler, W. R.; DIII-D Team

    2017-10-01

    The Metal Rings Campaign on DIII-D utilized two isotopically and poloidally distinct toroidal arrays of tungsten coated inserts in the lower divertor to study W divertor erosion near the outer strike point (OSP) and divertor entrance and subsequent migration in a mixed-material (C-W) environment. In AT hybrid discharges (PAUX = 14 MW, H98 = 1.6, βN = 3.7) with rapid ELMs (fELM 200 Hz, δW/W 0.7%) W impurities are seen to reach the midplane predominantly from the OSP region rather than the divertor entrance (far-SOL). Conversely, in scenarios with less frequent larger ELMs (fELM 60 Hz, δW/W 3.6%), the W impurities are found to transport equally from the OSP and entrance region. ELM-resolved spectroscopic measurements of W sourcing indicate that large ELMs can source W at many times the inter ELM rate. The peak W erosion rate can shift radially outwards consistent with the ELM energy flux, thereby shifting the balance between strikepoint and far-SOL sources. Changes in the peak erosion locations between forward and reversed Bt discharges are consistent with ExB ion drift effects. Evidence for a near-SOL impurity buildup between the divertors driven by the parallel grad-Ti force is also seen. Work supported under USDOE Cooperative Agreement DE-FC02-04ER54698.

  15. Quantitative analysis of external limiting membrane, ellipsoid zone and interdigitation zone defects in patients with macular holes.

    PubMed

    Houly, Jacques Ramos; Veloso, Carlos Eduardo; Passos, Elke; Nehemy, Márcio Bittar

    2017-07-01

    To investigate the correlation between the length of external limiting membrane (ELM), ellipsoid zone (EZ) and interdigitation zone (IZ) defects and visual prognosis in patients undergoing macular hole (MH) surgery, using spectral-domain optical coherence tomography (SD-OCT). This is a retrospective, consecutive, observational case series study. Fifty-two eyes of 52 patients with primary MH were evaluated. A quantitative analysis of ELM, EZ and IZ defects was performed preoperatively and at 3 and 6 months postoperatively using SD-OCT. The correlation between pre- and postoperative ELM, EZ and IZ defects and the best-corrected visual acuity (BCVA) was investigated. The lengths of ELM, EZ and IZ defects correlated significantly with BCVA in each study period (P < 0.001). Preoperative measures of these band defects were also associated with visual outcomes 3 and 6 months after surgery (P < 0.05). Considering all preoperative parameters, the length of the ELM defect was the factor most strongly correlated with BCVA at 6 months (β = 0.643, P < 0.012). The integrity of the ELM was the only factor significantly associated with BCVA at 6 months (β = 0.427; P = 0.004). The preoperative length of the ELM defect is the strongest predictor of visual acuity after MH surgery. Postoperative integrity of the ELM is significantly associated with visual restoration after surgical treatment of MH.

  16. Parsimonious extreme learning machine using recursive orthogonal least squares.

    PubMed

    Wang, Ning; Er, Meng Joo; Han, Min

    2014-10-01

    Novel constructive and destructive parsimonious extreme learning machines (CP- and DP-ELM) are proposed in this paper. By virtue of the proposed ELMs, parsimonious structure and excellent generalization of multiinput-multioutput single hidden-layer feedforward networks (SLFNs) are obtained. The proposed ELMs are developed by innovative decomposition of the recursive orthogonal least squares procedure into sequential partial orthogonalization (SPO). The salient features of the proposed approaches are as follows: 1) Initial hidden nodes are randomly generated by the ELM methodology and recursively orthogonalized into an upper triangular matrix with dramatic reduction in matrix size; 2) the constructive SPO in the CP-ELM focuses on the partial matrix with the subcolumn of the selected regressor including nonzeros as the first column while the destructive SPO in the DP-ELM operates on the partial matrix including elements determined by the removed regressor; 3) termination criteria for CP- and DP-ELM are simplified by the additional residual error reduction method; and 4) the output weights of the SLFN need not be solved in the model selection procedure and is derived from the final upper triangular equation by backward substitution. Both single- and multi-output real-world regression data sets are used to verify the effectiveness and superiority of the CP- and DP-ELM in terms of parsimonious architecture and generalization accuracy. Innovative applications to nonlinear time-series modeling demonstrate superior identification results.

  17. iELM—a web server to explore short linear motif-mediated interactions

    PubMed Central

    Weatheritt, Robert J.; Jehl, Peter; Dinkel, Holger; Gibson, Toby J.

    2012-01-01

    The recent expansion in our knowledge of protein–protein interactions (PPIs) has allowed the annotation and prediction of hundreds of thousands of interactions. However, the function of many of these interactions remains elusive. The interactions of Eukaryotic Linear Motif (iELM) web server provides a resource for predicting the function and positional interface for a subset of interactions mediated by short linear motifs (SLiMs). The iELM prediction algorithm is based on the annotated SLiM classes from the Eukaryotic Linear Motif (ELM) resource and allows users to explore both annotated and user-generated PPI networks for SLiM-mediated interactions. By incorporating the annotated information from the ELM resource, iELM provides functional details of PPIs. This can be used in proteomic analysis, for example, to infer whether an interaction promotes complex formation or degradation. Furthermore, details of the molecular interface of the SLiM-mediated interactions are also predicted. This information is displayed in a fully searchable table, as well as graphically with the modular architecture of the participating proteins extracted from the UniProt and Phospho.ELM resources. A network figure is also presented to aid the interpretation of results. The iELM server supports single protein queries as well as large-scale proteomic submissions and is freely available at http://i.elm.eu.org. PMID:22638578

  18. 76 FR 44318 - Combined Notice of Filings #1

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-25

    ... that the Commission received the following exempt wholesale generator filings: Docket Numbers: EG11-107-000. Applicants: Trinity Hills Wind Farm LLC. Description: Notice of Self-Certification of Exempt Wholesale Generator Status of Trinity Hills Wind Farm LLC. File Date: 07/15/2011. Accession Number: 20110715...

  19. 43 CFR 3583.4 - Hardrock mineral leases.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Hardrock mineral leases. 3583.4 Section... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.4 Hardrock mineral leases. ...

  20. 43 CFR 3583.4 - Hardrock mineral leases.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Hardrock mineral leases. 3583.4 Section... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.4 Hardrock mineral leases. ...

  1. 43 CFR 3583.4 - Hardrock mineral leases.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Hardrock mineral leases. 3583.4 Section... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.4 Hardrock mineral leases. ...

  2. 43 CFR 3583.4 - Hardrock mineral leases.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Hardrock mineral leases. 3583.4 Section... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.4 Hardrock mineral leases. ...

  3. Geologic framework, hydrostratigraphy, and ichnology of the Blanco, Payton, and Rough Hollow 7.5-minute quadrangles, Blanco, Comal, Hays, and Kendall Counties, Texas

    USGS Publications Warehouse

    Clark, Allan K.; Golab, James A.; Morris, Robert E.

    2016-09-13

    This report presents the geologic framework, hydro­stratigraphy, and ichnology of the Trinity and Edwards Groups in the Blanco, Payton, and Rough Hollow 7.5-minute quad­rangles in Blanco, Comal, Hays, and Kendall Counties, Texas. Rocks exposed in the study area are of the Lower Cretaceous Trinity Group and lower part of the Fort Terrett Formation of the Lower Cretaceous Edwards Group. The mapped units in the study area are the Hammett Shale, Cow Creek Limestone, Hensell Sand, and Glen Rose Limestone of the Trinity Group and the lower portion of the Fort Terrett Formation of the Edwards Group. The Glen Rose Limestone is composed of the Lower and Upper Members. These Trinity Group rocks con­tain the upper and middle Trinity aquifers. The only remaining outcrops of the Edwards Group are the basal nodular member of the Fort Terrett Formation, which caps several hills in the northern portion of the study area. These rocks were deposited in an open marine to supratidal flats environment. The faulting and fracturing in the study area are part of the Balcones fault zone, an extensional system of faults that generally trends southwest to northeast in south-central Texas.The hydrostratigraphic units of the Edwards and Trinity aquifers were mapped and described using a classification system based on fabric-selective or not-fabric-selective poros­ity types. The only hydrostratigraphic unit of the Edwards aquifer present in the study area is hydrostratigraphic unit VIII. The mapped hydrostratigraphic units of the upper Trinity aquifer are (from top to bottom) the Camp Bullis, upper evaporite, fossiliferous, and lower evaporite which are interval equivalent to the Upper Member of the Glen Rose Limestone. The middle Trinity aquifer encompasses (from top to bottom) the Lower Member of the Glen Rose Limestone, the Hensell Sand Member, and the Cow Creek Limestone Member of the Pearsall Formation. The Lower Member of the Glen Rose Limestone is subdivided into six informal hydro­stratigraphic units (from top to bottom) the Bulverde, Little Blanco, Twin Sisters, Doeppenschmidt, Rust, and Honey Creek hydrostratigraphic units.This study used the ichnofabric index scale to interpret the amount of bioturbation in the field. Most of the geologic units in the study area are assigned to the Cruziana and Thalassinoides ichnofacies consistent with interpretations of a tidal-dominated open marine environment (sublittoral zone). Ichnofossil assemblages are dominated by Thalassinoides networks, but also contain Cruziana, Ophiomorpha, Paleo­phycus, Planolites, and Serpulid traces.

  4. Impact of Te and ne on edge current density profiles in ELM mitigated regimes on ASDEX Upgrade

    NASA Astrophysics Data System (ADS)

    Dunne, M. G.; Rathgeber, S.; Burckhart, A.; Fischer, R.; Giannone, L.; McCarthy, P. J.; Schneider, P. A.; Wolfrum, E.; the ASDEX Upgrade Team

    2015-01-01

    ELM resolved edge current density profiles are reconstructed using the CLISTE equilibrium code. As input, highly spatially and temporally resolved edge electron temperature and density profiles are used in addition to data from the extensive set of external poloidal field measurements available at ASDEX Upgrade, flux loop difference measurements, and current measurements in the scrape-off layer. Both the local and flux surface averaged current density profiles are analysed for several ELM mitigation regimes. The focus throughout is on the impact of altered temperature and density profiles on the current density. In particular, many ELM mitigation regimes rely on operation at high density. Two reference plasmas with type-I ELMs are analysed, one with a deuterium gas puff and one without, in order to provide a reference for the behaviour in type-II ELMy regimes and high density ELM mitigation with external magnetic perturbations at ASDEX Upgrade. For type-II ELMs it is found that while a similar pedestal top pressure is sustained at the higher density, the temperature gradient decreases in the pedestal. This results in lower local and flux surface averaged current densities in these phases, which reduces the drive for the peeling mode. No significant differences between the current density measured in the type-I phase and ELM mitigated phase is seen when external perturbations are applied, though the pedestal top density was increased. Finally, ELMs during the nitrogen seeded phase of a high performance discharge are analysed and compared to ELMs in the reference phase. An increased pedestal pressure gradient, which is the source of confinement improvement in impurity seeded discharges, causes a local current density increase. However, the increased Zeff in the pedestal acts to reduce the flux surface averaged current density. This dichotomy, which is not observed in other mitigation regimes, could act to stabilize both the ballooning mode and the peeling mode at the same time.

  5. Spoken language identification based on the enhanced self-adjusting extreme learning machine approach.

    PubMed

    Albadr, Musatafa Abbas Abbood; Tiun, Sabrina; Al-Dhief, Fahad Taha; Sammour, Mahmoud A M

    2018-01-01

    Spoken Language Identification (LID) is the process of determining and classifying natural language from a given content and dataset. Typically, data must be processed to extract useful features to perform LID. The extracting features for LID, based on literature, is a mature process where the standard features for LID have already been developed using Mel-Frequency Cepstral Coefficients (MFCC), Shifted Delta Cepstral (SDC), the Gaussian Mixture Model (GMM) and ending with the i-vector based framework. However, the process of learning based on extract features remains to be improved (i.e. optimised) to capture all embedded knowledge on the extracted features. The Extreme Learning Machine (ELM) is an effective learning model used to perform classification and regression analysis and is extremely useful to train a single hidden layer neural network. Nevertheless, the learning process of this model is not entirely effective (i.e. optimised) due to the random selection of weights within the input hidden layer. In this study, the ELM is selected as a learning model for LID based on standard feature extraction. One of the optimisation approaches of ELM, the Self-Adjusting Extreme Learning Machine (SA-ELM) is selected as the benchmark and improved by altering the selection phase of the optimisation process. The selection process is performed incorporating both the Split-Ratio and K-Tournament methods, the improved SA-ELM is named Enhanced Self-Adjusting Extreme Learning Machine (ESA-ELM). The results are generated based on LID with the datasets created from eight different languages. The results of the study showed excellent superiority relating to the performance of the Enhanced Self-Adjusting Extreme Learning Machine LID (ESA-ELM LID) compared with the SA-ELM LID, with ESA-ELM LID achieving an accuracy of 96.25%, as compared to the accuracy of SA-ELM LID of only 95.00%.

  6. Spoken language identification based on the enhanced self-adjusting extreme learning machine approach

    PubMed Central

    Tiun, Sabrina; AL-Dhief, Fahad Taha; Sammour, Mahmoud A. M.

    2018-01-01

    Spoken Language Identification (LID) is the process of determining and classifying natural language from a given content and dataset. Typically, data must be processed to extract useful features to perform LID. The extracting features for LID, based on literature, is a mature process where the standard features for LID have already been developed using Mel-Frequency Cepstral Coefficients (MFCC), Shifted Delta Cepstral (SDC), the Gaussian Mixture Model (GMM) and ending with the i-vector based framework. However, the process of learning based on extract features remains to be improved (i.e. optimised) to capture all embedded knowledge on the extracted features. The Extreme Learning Machine (ELM) is an effective learning model used to perform classification and regression analysis and is extremely useful to train a single hidden layer neural network. Nevertheless, the learning process of this model is not entirely effective (i.e. optimised) due to the random selection of weights within the input hidden layer. In this study, the ELM is selected as a learning model for LID based on standard feature extraction. One of the optimisation approaches of ELM, the Self-Adjusting Extreme Learning Machine (SA-ELM) is selected as the benchmark and improved by altering the selection phase of the optimisation process. The selection process is performed incorporating both the Split-Ratio and K-Tournament methods, the improved SA-ELM is named Enhanced Self-Adjusting Extreme Learning Machine (ESA-ELM). The results are generated based on LID with the datasets created from eight different languages. The results of the study showed excellent superiority relating to the performance of the Enhanced Self-Adjusting Extreme Learning Machine LID (ESA-ELM LID) compared with the SA-ELM LID, with ESA-ELM LID achieving an accuracy of 96.25%, as compared to the accuracy of SA-ELM LID of only 95.00%. PMID:29672546

  7. Initial Assessments of E-Learning Modules in Cytotechnology Education.

    PubMed

    Mukherjee, Maheswari S; Donnelly, Amber D

    2018-01-01

    Nine E-learning modules (ELMs) were developed in our program using Articulate software. This study assessed our cytotechnology (CT) students' perceptions on the content of the ELMs, and the perceived influence of the ELMs on students' performance during clinical rotations. All CT students watched nine ELMs before the related classroom lecture and group discussion. Following that, students completed nine preclinical rotation surveys. After their clinical rotations, students completed nine postclinical rotation surveys. Statements on the content of the ELMs regarding the quality of the video and audio, duration, navigation, and the materials presented, received positive responses from the majority of the students. While there were a few disagreements and neutral responses, most of the students responded positively saying that the ELMs better prepared them for their role, as well as helped them to better perform their roles during the clinical rotation. The majority of the students recommended developing more EMLs for cytology courses in the future. This study has given hope that the ELMs have potential to enhance our online curriculum and benefit students, within the United States and internationally, who have no easy access to cytology clinical laboratories for hands-on training.

  8. Stabilizing effect of resistivity towards ELM-free H-mode discharge in lithium-conditioned NSTX

    NASA Astrophysics Data System (ADS)

    Banerjee, Debabrata; Zhu, Ping; Maingi, Rajesh

    2017-07-01

    Linear stability analysis of the national spherical torus experiment (NSTX) Li-conditioned ELM-free H-mode equilibria is carried out in the context of the extended magneto-hydrodynamic (MHD) model in NIMROD. The purpose is to investigate the physical cause behind edge localized mode (ELM) suppression in experiment after the Li-coating of the divertor and the first wall of the NSTX tokamak. Besides ideal MHD modeling, including finite-Larmor radius effect and two-fluid Hall and electron diamagnetic drift contributions, a non-ideal resistivity model is employed, taking into account the increase of Z eff after Li-conditioning in ELM-free H-mode. Unlike an earlier conclusion from an eigenvalue code analysis of these equilibria, NIMROD results find that after reduced recycling from divertor plates, profile modification is necessary but insufficient to explain the mechanism behind complete ELMs suppression in ideal two-fluid MHD. After considering the higher plasma resistivity due to higher Z eff, the complete stabilization could be explained. A thorough analysis of both pre-lithium ELMy and with-lithium ELM-free cases using ideal and non-ideal MHD models is presented, after accurately including a vacuum-like cold halo region in NIMROD to investigate ELMs.

  9. Comparative ELM study between the observation by ECEI and linear/nonlinear simulation in the KSTAR plasmas

    NASA Astrophysics Data System (ADS)

    Kim, Minwoo; Park, Hyeon K.; Yun, Gunsu; Lee, Jaehyun; Lee, Jieun; Lee, Woochang; Jardin, Stephen; Xu, X. Q.; Kstar Team

    2015-11-01

    The modeling of the Edge-localized-mode (ELM) should be rigorously pursued for reliable and robust ELM control for steady-state long-pulse H-mode operation in ITER as well as DEMO. In the KSTAR discharge #7328, a linear stability of the ELMs is investigated using M3D-C1 and BOUT + + codes. This is achieved by linear simulation for the n = 8 mode structure of the ELM observed by the KSTAR electron cyclotron emission imaging (ECEI) systems. In the process of analysis, variations due to the plasma equilibrium profiles and transport coefficients on the ELM growth rate are investigated and simulation results with the two codes are compared. The numerical simulations are extended to nonlinear phase of the ELM dynamics, which includes saturation and crash of the modes. Preliminary results of the nonlinear simulations are compared with the measured images especially from the saturation to the crash. This work is supported by NRF of Korea under contract no. NRF-2014M1A7A1A03029865, US DoE by LLNL under contract DE-AC52-07NA27344 and US DoE by PPPL under contract DE-AC02-09CH11466.

  10. Plant signals during beetle (Scolytus multistriatus) feeding in American elm (Ulmus americana Planch).

    PubMed

    Saremba, Brett M; Tymm, Fiona J M; Baethke, Kathy; Rheault, Mark R; Sherif, Sherif M; Saxena, Praveen K; Murch, Susan J

    2017-05-04

    American Elms were devastated by an outbreak of Dutch Elm Disease is caused by the fungus Ophiostoma novo-ulmi Brasier that originated in Asia and arrived in the early 1900s. In spite of decades of study, the specific mechanisms and disease resistance in some trees is not well understood. the fungus is spread by several species of bark beetles in the genus Scolytus, during their dispersal and feeding. Our objective was to understand elm responses to beetle feeding in the absence of the fungus to identify potential resistance mechanisms. A colony of Scolytus multistriatus was established from wild-caught beetles and beetles were co-incubated with susceptible or resistant American elm varieties in a controlled environment chamber. Beetles burrowed into the auxillary meristems of the young elm shoots. The trees responded to the beetle damage by a series of spikes in the concentration of plant growth regulating compounds, melatonin, serotonin, and jasmonic acid. Spikes in melatonin and serotonin represented a 7,000-fold increase over resting levels. Spikes in jasmonic acid were about 10-fold higher than resting levels with one very large spike observed. Differences were noted between susceptible and resistant elms that provide new understanding of plant defenses.

  11. The Case of Trinity University: Collegial Rift, Mission Drift, Corporate Shift

    ERIC Educational Resources Information Center

    Twale, Darla J.; Place, A. William

    2006-01-01

    The case of Trinity University is an ideal way to introduce graduate students in educational leadership preparation programs to the university culture and how it shapes the graduate curriculum, faculty expectations for student outcomes, and professional socialization processes. Master's and doctoral students who take courses related to cultural…

  12. 75 FR 6791 - Surety Companies Acceptable on Federal Bonds-Termination: Trinity Universal Insurance Company

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-10

    ... DEPARTMENT OF THE TREASURY Fiscal Service Surety Companies Acceptable on Federal Bonds--Termination: Trinity Universal Insurance Company AGENCY: Financial Management Service, Fiscal Service... that the Certificate of Authority issued by the Treasury to the above-named company under 31 U.S.C...

  13. 76 FR 30902 - Shasta Lake Management Unit, Shasta-Trinity National Forest; California; Green-Horse Habitat...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-27

    ... management strategy to allow modification of treatments if necessary during implementation. A project-level... to 15 tons per acre for those two management prescriptions. This project-level amendment is proposed... Management Unit, Shasta-Trinity National Forest; California; Green-Horse Habitat Restoration and Maintenance...

  14. 76 FR 4365 - Renewal of the Trinity River Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-25

    ... Management Working Group AGENCY: Office of the Secretary, Interior. ACTION: Notice. SUMMARY: The Secretary of... Trinity River Adaptive Management Working Group (Working Group) for 2 years. The Working Group provides... Road, Arcata, CA 95521; 707-822-7201. SUPPLEMENTARY INFORMATION: The Working Group conducts its...

  15. 78 FR 5830 - Renewal of the Trinity River Adaptive Management Working Group

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-28

    ... Management Working Group AGENCY: Office of the Secretary, Interior. ACTION: Notice. SUMMARY: The Secretary of... Trinity River Adaptive Management Working Group (Working Group) for 2 years. The Working Group provides... Road, Arcata, CA 95521; 707-822-7201. SUPPLEMENTARY INFORMATION: The Working Group conducts its...

  16. Simulating sediment loading into the major reservoirs in Trinity River Basin

    USDA-ARS?s Scientific Manuscript database

    The Upper Trinity Basin supplies water to about one-fourth of Texas' population. The anticipated rapid growth of North Central Texas will certainly increase regional demands for high quality drinking water. This has increased concerns that sediment and nutrient loads received by drinking water reser...

  17. A program to assess a thermal discharge on Trinity Bay, Texas

    NASA Technical Reports Server (NTRS)

    Zaitzeff, J. B.; Whitehead, V. S.

    1972-01-01

    The application of a two dimensional mathematical model to the analysis of the thermal discharge to verify its ability to predict the temperature distribution of Trinity Bay in the vicinity of the water outfall. Basic data consist of aerial thermal infrared and in situ measurements.

  18. 43 CFR 3583.1-1 - Leasable minerals.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Leasable minerals. 3583.1-1 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-1 Leasable minerals. Except as otherwise...

  19. 43 CFR 3583.1-2 - Hardrock minerals.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Hardrock minerals. 3583.1-2 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-2 Hardrock minerals. This subpart governs the...

  20. 43 CFR 3583.1-2 - Hardrock minerals.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Hardrock minerals. 3583.1-2 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-2 Hardrock minerals. This subpart governs the...

  1. 43 CFR 3583.1-2 - Hardrock minerals.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Hardrock minerals. 3583.1-2 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-2 Hardrock minerals. This subpart governs the...

  2. 43 CFR 3583.1-1 - Leasable minerals.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Leasable minerals. 3583.1-1 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-1 Leasable minerals. Except as otherwise...

  3. 43 CFR 3583.1-1 - Leasable minerals.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Leasable minerals. 3583.1-1 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-1 Leasable minerals. Except as otherwise...

  4. 43 CFR 3583.1-1 - Leasable minerals.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Leasable minerals. 3583.1-1 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-1 Leasable minerals. Except as otherwise...

  5. 43 CFR 3583.1-2 - Hardrock minerals.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Hardrock minerals. 3583.1-2 Section 3583.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and Trinity Units of the Whiskeytown-Shasta-Trinity National Recreation Area § 3583.1-2 Hardrock minerals. This subpart governs the...

  6. Assembly interdependence among the S. cerevisiae bud neck ring proteins Elm1p, Hsl1p and Cdc12p.

    PubMed

    Thomas, Courtney L; Blacketer, Melissa J; Edgington, Nicholas P; Myers, Alan M

    2003-07-15

    In Saccharomyces cerevisiae, a complex comprising more than 20 different polypeptides assembles in a ring at the neck between the mother cell and the bud. This complex functions to coordinate cell morphology with cell division. Relatively little is known about this control system, including the physical relationships between the components of the neck ring. This study addressed the assembly interactions of three components of the ring, specifically the protein kinases Elm1p and Hsl1p and the septin Cdc12p. Specific amino acid substitutions in each of these three proteins were identified that either cause or suppress a characteristic phenotype of abnormally elongated cells and delay in the G(2)-M transition. Each protein was fused to green fluorescent protein, and its ability to localize at the neck was monitored in vivo in cells of various genotypes. Localization of Hsl1p to the neck requires Elm1p function. Elm1p localized normally in the absence of Hsl1p, although a specific point mutation in Hsl1p clearly affected Elm1p localization. The cdc12-122 mutation prevented assembly of Elm1p or Hsl1p into the neck ring. Normal assembly of Cdc12p at the neck was dependent upon Elm1p and also, to a smaller extent, on Hsl1p. Ectopic localization of Cdc12p at the bud tip was observed frequently in elm1 mutants and also, to a lesser extent, in hsl1 mutants. Thus, Elm1p is a key factor in the assembly and/or maintenance of Hsl1p, as well as at least one septin, into the bud neck ring. Copyright 2003 John Wiley & Sons, Ltd.

  7. Is extreme learning machine feasible? A theoretical assessment (part I).

    PubMed

    Liu, Xia; Lin, Shaobo; Fang, Jian; Xu, Zongben

    2015-01-01

    An extreme learning machine (ELM) is a feedforward neural network (FNN) like learning system whose connections with output neurons are adjustable, while the connections with and within hidden neurons are randomly fixed. Numerous applications have demonstrated the feasibility and high efficiency of ELM-like systems. It has, however, been open if this is true for any general applications. In this two-part paper, we conduct a comprehensive feasibility analysis of ELM. In Part I, we provide an answer to the question by theoretically justifying the following: 1) for some suitable activation functions, such as polynomials, Nadaraya-Watson and sigmoid functions, the ELM-like systems can attain the theoretical generalization bound of the FNNs with all connections adjusted, i.e., they do not degrade the generalization capability of the FNNs even when the connections with and within hidden neurons are randomly fixed; 2) the number of hidden neurons needed for an ELM-like system to achieve the theoretical bound can be estimated; and 3) whenever the activation function is taken as polynomial, the deduced hidden layer output matrix is of full column-rank, therefore the generalized inverse technique can be efficiently applied to yield the solution of an ELM-like system, and, furthermore, for the nonpolynomial case, the Tikhonov regularization can be applied to guarantee the weak regularity while not sacrificing the generalization capability. In Part II, however, we reveal a different aspect of the feasibility of ELM: there also exists some activation functions, which makes the corresponding ELM degrade the generalization capability. The obtained results underlie the feasibility and efficiency of ELM-like systems, and yield various generalizations and improvements of the systems as well.

  8. Physics of thermal transport and increased electron temperature turbulence in the edge pedestal of ELM-free, H-mode regimes on DIII-D

    NASA Astrophysics Data System (ADS)

    Sung, Choongki

    2017-10-01

    It has been observed, for the first time, that suppression of Edge Localized Modes (ELMs) in tokamak plasmas is accompanied by an increase in electron temperature turbulence. A correlation electron cyclotron emission technique has been utilized to quantify the observed increase: 40% increase in Quiescent H-mode (QH-mode) and 70% increase in 3D field ELM suppressed H-mode. Since reliable ELM-free H-mode operation is essential for future burning plasma experiments, it is crucial to develop a validated predictive capability for these plasmas. Linear stability analysis using TGLF has provided an explanation for the observations and has indicated that the underlying physical mechanisms are different in the two regimes. In QH-mode, profile gradients and the associated linear growth rate are decreased compared to ELMing H-mode. However, the ExB shearing rate is reduced by an even greater factor such that turbulent transport is no longer suppressed by flow shear. In contrast, during 3D field ELM suppressed H-mode, gradients are increased and TGLF predicts that a large increase in linear growth rate is primarily responsible for the increased turbulence. Power balance analysis using ONETWO is also consistent with the changes in electron thermal transport being due to the increased turbulence. These new findings are significant since they i) provide a physics explanation of these changes via TGLF analysis and enable validation of the model in the key pedestal region, and ii) support the hypothesis that turbulent transport partially replaces ELM-dominated transport during ELM-free operation. These results form a basis to develop a predictive understanding of pedestal regulation in ELM suppressed regimes. Supported by the US DOE under DE-FG02-08ER54984, DE-FC02-04ER54698.

  9. Experimental validation of coil phase parametrisation on ASDEX Upgrade, and extension to ITER

    NASA Astrophysics Data System (ADS)

    Ryan, D. A.; Liu, Y. Q.; Kirk, A.; Suttrop, W.; Dudson, B.; Dunne, M.; Willensdorfer, M.; the ASDEX Upgrade team; the EUROfusion MST1 team

    2018-06-01

    It has been previously demonstrated in Li et al (2016 Nucl. Fusion 56 126007) that the optimum upper/lower coil phase shift ΔΦopt for alignment of RMP coils for ELM mitigation depends sensitively on q 95, and other equilibrium plasma parameters. Therefore, ΔΦopt is expected to vary widely during the current ramp of ITER plasmas, with negative implications for ELM mitigation during this period. A previously derived and numerically benchmarked parametrisation of the coil phase for optimal ELM mitigation on ASDEX Upgrade (Ryan et al 2017 Plasma Phys. Control. Fusion 59 024005) is validated against experimental measurements of ΔΦopt, made by observing the changes to the ELM frequency as the coil phase is scanned. It is shown that the parametrisation may predict the optimal coil phase to within 32° of the experimental measurement for n = 2 applied perturbations. It is explained that this agreement is sufficient to ensure that the ELM mitigation is not compromised by poor coil alignment. It is also found that the phase which maximises ELM mitigation is shifted from the phase which maximizes density pump-out, in contrast to theoretical expectations that ELM mitigation and density pump out have the same ΔΦ ul dependence. A time lag between the ELM frequency response and density response to the RMP is suggested as the cause. The method for numerically deriving the parametrisation is repeated for the ITER coil set, using the baseline scenario as a reference equilibrium, and the parametrisation coefficients given for future use in a feedback coil alignment system. The relative merits of square or sinusoidal toroidal current waveforms for ELM mitigation are briefly discussed.

  10. Statistical Characterization and Classification of Edge-Localized Plasma Instabilities

    NASA Astrophysics Data System (ADS)

    Webster, A. J.; Dendy, R. O.

    2013-04-01

    The statistics of edge-localized plasma instabilities (ELMs) in toroidal magnetically confined fusion plasmas are considered. From first principles, standard experimentally motivated assumptions are shown to determine a specific probability distribution for the waiting times between ELMs: the Weibull distribution. This is confirmed empirically by a statistically rigorous comparison with a large data set from the Joint European Torus. The successful characterization of ELM waiting times enables future work to progress in various ways. Here we present a quantitative classification of ELM types, complementary to phenomenological approaches. It also informs us about the nature of ELM processes, such as whether they are random or deterministic. The methods are extremely general and can be applied to numerous other quasiperiodic intermittent phenomena.

  11. VizieR Online Data Catalog: The ELM survey. VI. 11 new ELM WD binaries (Gianninas+, 2015)

    NASA Astrophysics Data System (ADS)

    Gianninas, A.; Kilic, M.; Brown, W. R.; Canton, P.; Kenyon, S. J.

    2016-02-01

    We used the 6.5m MMT telescope equipped with the Blue Channel spectrograph, the 200 inch Hale telescope equipped with the Double spectrograph, the Kitt Peak National Observatory 4m telescope equipped with the R-C spectrograph, and more recently with Kitt Peak Ohio State Multi-Object Spectrograph (KOSMOS), to obtain spectroscopy of our 11 targets in several observing runs. We have also been obtaining radial-velocity measurements for candidates from other sources including the Large Sky Area Multi-Object Spectroscopy Telescope (LAMOST). Those 11 new Extremely low-mass white dwarf (ELM WD) binaries bring the total of ELM WDs identified by the ELM Survey up to 73. (4 data files).

  12. 8. View of Clark Fork Vehicle Bridge facing southwest. Looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. View of Clark Fork Vehicle Bridge facing southwest. Looking at understructure of northernmost span. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  13. 20. View of Clark Fork Vehicle Bridge facing up. Looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. View of Clark Fork Vehicle Bridge facing up. Looking at understructure of northernmost span. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  14. Dutch Elm Disease and Methoxychlor

    Treesearch

    Jack H. Barger

    1976-01-01

    American elm trees, Ulmus americana L., in Milwaukee, Wisconsin, were sprayed with methoxychlor by helicopter or mist blower once each year for 3 years to control the smaller European elm bark beetle Scolytus multistriatus (Marsham). Twig crotches were collected from sprayed trees each year for bioassay. Methoxychlor residues...

  15. Mitigation of divertor heat flux by high-frequency ELM pacing with non-fuel pellet injection in DIII-D

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bortolon, A.; Maingi, R.; Mansfield, D. K.

    Experiments have been conducted on DIII-D investigating high repetition rate injection of non-fuel pellets as a tool for pacing Edge Localized Modes (ELMs) and mitigating their transient divertor heat loads. Effective ELM pacing was obtained with injection of Li granules in different H-mode scenarios, at frequencies 3–5 times larger than the natural ELM frequency, with subsequent reduction of strike-point heat flux. However, in scenarios with high pedestal density (~6 × 10 19 m –3), the magnitude of granule triggered ELMs shows a broad distribution, in terms of stored energy loss and peak heat flux, challenging the effectiveness of ELM mitigation.more » Furthermore, transient heat-flux deposition correlated with granule injections was observed far from the strike-points. As a result, field line tracing suggest this phenomenon to be consistent with particle loss into the mid-plane far scrape-off layer, at toroidal location of the granule injection.« less

  16. Mitigation of divertor heat flux by high-frequency ELM pacing with non-fuel pellet injection in DIII-D

    DOE PAGES

    Bortolon, A.; Maingi, R.; Mansfield, D. K.; ...

    2017-03-23

    Experiments have been conducted on DIII-D investigating high repetition rate injection of non-fuel pellets as a tool for pacing Edge Localized Modes (ELMs) and mitigating their transient divertor heat loads. Effective ELM pacing was obtained with injection of Li granules in different H-mode scenarios, at frequencies 3–5 times larger than the natural ELM frequency, with subsequent reduction of strike-point heat flux. However, in scenarios with high pedestal density (~6 × 10 19 m –3), the magnitude of granule triggered ELMs shows a broad distribution, in terms of stored energy loss and peak heat flux, challenging the effectiveness of ELM mitigation.more » Furthermore, transient heat-flux deposition correlated with granule injections was observed far from the strike-points. As a result, field line tracing suggest this phenomenon to be consistent with particle loss into the mid-plane far scrape-off layer, at toroidal location of the granule injection.« less

  17. 18. View of Clark Fork Vehicle Bridge facing north. Looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. View of Clark Fork Vehicle Bridge facing north. Looking at north concrete abutment and timber stringers. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  18. INCREASED SERUM LEVELS OF UREA AND CREATININE ARE SURROGATE MARKERS FOR DISRUPTION OF RETINAL PHOTORECEPTOR EXTERNAL LIMITING MEMBRANE AND INNER SEGMENT ELLIPSOID ZONE IN TYPE 2 DIABETES MELLITUS.

    PubMed

    Saxena, Sandeep; Ruia, Surabhi; Prasad, Senthamizh; Jain, Astha; Mishra, Nibha; Natu, Shankar M; Meyer, Carsten H; Gilhotra, Jagjit S; Kruzliak, Peter; Akduman, Levent

    2017-02-01

    To evaluate the role of serum urea and creatinine as surrogate markers for disruption of retinal photoreceptor external limiting membrane (ELM) and inner segment ellipsoid zone (EZ) in Type 2 diabetic retinopathy (DR) using spectral-domain optical coherence tomography, for the first time. One hundred and seventeen consecutive cases of Type 2 diabetes mellitus (diabetes without retinopathy [No DR; n = 39], nonproliferative diabetic retinopathy [NPDR; n = 39], proliferative diabetic retinopathy [PDR; n = 39]) and 40 healthy control subjects were included. Serum levels of urea and creatinine were assessed using standard protocol. Spectral-domain optical coherence tomography was used to grade the disruption of ELM and EZ as follows: Grade 0, no disruption of ELM and EZ; Grade 1, ELM disrupted, EZ intact; Grade 2, ELM and EZ disrupted. Data were analyzed statistically. Increase in serum levels of urea (F = 22.93) and creatinine (F = 15.82) and increased grades of disruption of ELM and EZ (γ = 116.3) were observed with increased severity of DR (P < 0.001). Increase in serum levels of urea (F = 10.45) and creatinine (F = 6.89) was observed with increased grades of disruption of ELM and EZ (P = 0.001). Serum levels of urea and creatinine are surrogate markers for disruption of retinal photoreceptor ELM and EZ on spectral-domain optical coherence tomography in DR.

  19. Characterization of streamflow, suspended sediment, and nutrients entering Galveston Bay from the Trinity River, Texas, May 2014–December 2015

    USGS Publications Warehouse

    Lucena, Zulimar; Lee, Michael T.

    2017-02-21

    The U.S. Geological Survey (USGS), in cooperation with the Texas Water Development Board and the Galveston Bay Estuary Program, collected streamflow and water-quality data at USGS streamflow-gaging stations in the lower Trinity River watershed from May 2014 to December 2015 to characterize and improve the current understanding of the quantity and quality of freshwater inflow entering Galveston Bay from the Trinity River. Continuous streamflow records at four USGS streamflow-gaging stations were compared to quantify differences in streamflow magnitude between upstream and downstream reaches of the lower Trinity River. Water-quality conditions were characterized from discrete nutrient and sedi­ment samples collected over a range of hydrologic conditions at USGS streamflow-gaging station 08067252 Trinity River at Wallisville, Tex. (hereinafter referred to as the “Wallisville site”), approximately 4 river miles upstream from where the Trinity River enters Galveston Bay.Based on streamflow records, annual mean outflow from Livingston Dam into the lower Trinity River was 2,240 cubic feet per second (ft3/s) in 2014 and 22,400 ft3/s in 2015, the second lowest and the highest, respectively, during the entire period of record (1966–2015). During this study, only about 54 percent of the total volume measured at upstream sites was accounted for at the Wallisville site as the Trinity River enters Galveston Bay. This difference in water volumes between upstream sites and the Wallisville site indicates that at high flows a large part of the volume released from Lake Livingston does not reach Galveston Bay through the main channel of the Trinity River. These findings indicate that water likely flows into wetlands and water bodies surrounding the main channel of the Trinity River before reaching the Wallisville site and is being stored or discharged through other channels that flow directly into Galveston Bay.To characterize suspended-sediment concentrations and loads in Trinity River inflow to Galveston Bay, a regression model was developed to estimate suspended-sediment concentrations by using acoustic backscatter data as a surrogate. The model yielded an adjusted coefficient of determination value of 0.92 and a root mean square error of 1.65 milligrams per liter (mg/L). The mean absolute percentage error between measured and estimated suspended-sediment concentration was 35 percent. During this study, estimated suspended-sediment concentrations ranged from 2 to 701 mg/L, with a mean of 97 mg/L. Suspended-sediment concentrations varied in response to changes in discharge, with peak suspended-sediment concentrations occurring 1 to 2 days before the peak discharge for each event. The total suspended-sediment load at the Wallisville site during May 2014–December 2015 was approximately 2,200,000 tons, with a minimum monthly suspended-sediment load of 100 tons in October 2014 and a maximum monthly load of 441,000 tons in November 2015.Results from nutrient samples collected at the Wallisville site indicate that total nitrogen and total phosphorus concen­trations fluctuated at a similar rate, with the highest nutrient concentrations occurring during periods of high flow corresponding to releases from Lake Livingston. The mean concen­trations of total nitrogen and total phosphorus were approxi­mately 75 percent higher during high flow releases than during periods of low flow, overshadowing variations in nutrient concentrations caused by seasonality at the Wallisville site.Results from the study indicate nutrient delivery to Galveston Bay from the main channel of the Trinity River is likely controlled primarily by high-flow releases from Lake Livingston. For most samples collected at the Wallisville site, organic nitrogen was the predominant form of nitrogen; however, when discharge increased because of releases from Lake Livingston, the percentage of organic nitrogen typically decreased and the percentage of nitrate increased. The concentrations of total phosphorus also increased during high-flow events, likely as a result of suspended sediment within Lake Livingston releases and mobilization of sediment particles in the river channel and flood plain during these periods of high flow. The predominant source of phosphorous to Galveston Bay from the Trinity River is in particulate form closely tied to suspended-sediment concentrations. The changes in nutrient concentration and composition caused by releases from Lake Livingston during this study indicate the reservoir may play an important role in the delivery of nutrients into Galveston Bay. Further study is required to better understand the processes in Lake Livingston influencing the characteristics of nutrient and sediment inflow to Galveston Bay. With phosphorous concentrations correlated to suspended-sediment concentra­tions (coefficient of determination value of 0.75) and with the concentrations of nutrients changing as the discharge changes, the diversion of water and suspended sediment into surround­ing wetlands and channels outside of the main channel of the Trinity River may play a large role in regulating nutrient inputs into Galveston Bay.

  20. American Elm clones of importance in DED tolerance studies

    USDA-ARS?s Scientific Manuscript database

    We present the background and characteristics of American elm clones that are commercially available or of interest in research on Dutch elm disease (DED) tolerance in the United States. The characteristics of interest include origin, ploidy level, whether available in nursery trade, evidence of DED...

  1. 19. View of Clark Fork Vehicle Bridge facing north. Looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. View of Clark Fork Vehicle Bridge facing north. Looking at north abutment and underside of northernmost span. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  2. 22. View of Clark Fork Vehicle Bridge facing downwest side. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    22. View of Clark Fork Vehicle Bridge facing down-west side. Looking at road deck and vertical laced channel. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  3. 21. View of Clark Fork Vehicle Bridge facing west. Looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    21. View of Clark Fork Vehicle Bridge facing west. Looking at bridge deck, guard rail, juncture of two bridge spans. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  4. 11. View of Clark Fork Vehicle Bridge facing northwest. Southernmost ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    11. View of Clark Fork Vehicle Bridge facing northwest. Southernmost span. Plaque was originally located where striped traffic sign is posted. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  5. Trinity's "Legal Detectives" Stalk Jack the Ripper: Would Socrates Have Approved?

    ERIC Educational Resources Information Center

    Mangan, Katherine S.

    1989-01-01

    Trinity University's philosophy laboratory provides a think tank for philosophy students, allowing them to practice such skills as logic, critical reasoning, and the application of moral responsibility in decision-making by applying their skills to real-life situations. Students, selected as fellows and paid, are divided into teams for projects.…

  6. Certificated Master Contract Agreement for 1987-90, Shasta-Tehama-Trinity Joint Community College District.

    ERIC Educational Resources Information Center

    Shasta-Tehama-Trinity Joint Community Coll. District, Redding, CA.

    This collective bargaining agreement between the Shasta-Tehama-Trinity Joint Community College District and the Shasta College Faculty Association establishes conditions of employment for all full- and part-time regular or contracted certificated employees of the district. The articles of the agreement set forth provisions related to: (1)…

  7. 75 FR 62424 - EDS, an HP Company (Re-Branded as HP-Enterprise Services) Including On-Site Workers From: Abel...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-08

    ... Floyd and Company, Trinity Government SYS a Private Co, Verizon Network Integration Corp, Vision... Provider Inc., Teksystems, The Experts Inc., TM Floyd and Company, Trinity Government SYS a Private Co... Compuware Corp Comsys Information Technology SVC, Diversified Systems Inc., E- Corn LLC, Farrington...

  8. The Elaboration Likelihood Model: Implications for the Practice of School Psychology.

    ERIC Educational Resources Information Center

    Petty, Richard E.; Heesacker, Martin; Hughes, Jan N.

    1997-01-01

    Reviews a contemporary theory of attitude change, the Elaboration Likelihood Model (ELM) of persuasion, and addresses its relevance to school psychology. Claims that a key postulate of ELM is that attitude change results from thoughtful (central route) or nonthoughtful (peripheral route) processes. Illustrations of ELM's utility for school…

  9. Cephalosporium Wilt of Elm in the Lower Mississippi Valley

    Treesearch

    T. H. Filer; F. I. McCracken; E. R. Toole

    1968-01-01

    Dead and dying American elms (Ulmus americana) and cedar elms (U. crassifolia) were observed on the Delta Experimental Forest, Stoneville, Mississippi, and in Desha County, Arkansas, near the Mississippi River (about 30 miles northwest of the experimental forest) during August 1967. The only fungus consistently isolated from these...

  10. 77 FR 36206 - Airworthiness Directives; The Boeing Company Airplanes

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-18

    ... experienced smoke and heat damage from insulation blankets that smoldered after molten debris from a P200 ELMS power panel fell on the insulation blankets. When a contactor in the ELMS panel fails and overheats, the... ELMS contactor breakdown, consequent smoke and heat damage to airplane structure and equipment during...

  11. Ulmus americana is a polyploid complex

    USDA-ARS?s Scientific Manuscript database

    The elms (the genus Ulmus) are one of the most important tree crops for the $4.7-billion per year nursery industry. The commercial importance of the genus centers on the American elm, Ulmus americana. Once decimated by Dutch Elm Disease, the recent introduction of cultivars resistant to the diseas...

  12. Suppression of type-I ELMs with reduced RMP coil set on DIII-D

    DOE PAGES

    Orlov, Dmitriy M.; Moyer, Richard A.; Evans, Todd E.; ...

    2016-02-19

    Recent experiments on DIII-D have demonstrated that having a toroidally-monochromatic spectral content of edge-resonant magnetic perturbations (RMPs) is not a necessary condition for suppression of Edge Localized Modes (ELMs). Robust ELM suppression has been reproducibly obtained on DIII-D during experiments in which various non-axisymmetric coil loops were turned off pseudo-randomly producing a variety of n=1, n=2, and n=3 spectral contributions. It was shown that RMP ELM suppression could be achieved with as few as 5 out of 12 internal coil loops (I-coils) on DIII-D at similar coil currents and with good plasma confinement. Linear MHD plasma response (M3DC1, IPEC, MARS)more » and vacuum (SURFMN, TRIP3D) modeling have been performed in order to understand the effects of the perturbation spectrum on the plasma response and ELM suppression. The results suggest that reduction of the dominant n=3 perturbation field is compensated by increased n=2 field in the plasma that may lead to RMP ELM suppression at lower levels of n=3 perturbative magnetic flux from the I-coils. These results provide additional confidence that ITER may be capable of RMP ELM suppression in the event of multiple internal coil failures.« less

  13. Stabilizing effect of resistivity towards ELM-free H-mode discharge in lithium-conditioned NSTX

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Banerjee, Debabrata; Zhu, Ping; Maingi, Rajesh

    Linear stability analysis of the national spherical torus experiment (NSTX) Li-conditioned ELM-free H-mode equilibria is carried out in the context of the extended magneto-hydrodynamic (MHD) model in NIMROD. Our purpose is to investigate the physical cause behind edge localized mode (ELM) suppression in experiment after the Li-coating of the divertor and the first wall of the NSTX tokamak. Besides ideal MHD modeling, including finite-Larmor radius effect and two-fluid Hall and electron diamagnetic drift contributions, a non-ideal resistivity model is employed, taking into account the increase of Z eff after Li-conditioning in ELM-free H-mode. And unlike an earlier conclusion from anmore » eigenvalue code analysis of these equilibria, NIMROD results find that after reduced recycling from divertor plates, profile modification is necessary but insufficient to explain the mechanism behind complete ELMs suppression in ideal two-fluid MHD. After considering the higher plasma resistivity due to higher Z eff, the complete stabilization could be explained. Furthermore, a thorough analysis of both pre-lithium ELMy and with-lithium ELM-free cases using ideal and non-ideal MHD models is presented, after accurately including a vacuum-like cold halo region in NIMROD to investigate ELMs.« less

  14. Stabilizing effect of resistivity towards ELM-free H-mode discharge in lithium-conditioned NSTX

    DOE PAGES

    Banerjee, Debabrata; Zhu, Ping; Maingi, Rajesh

    2017-05-12

    Linear stability analysis of the national spherical torus experiment (NSTX) Li-conditioned ELM-free H-mode equilibria is carried out in the context of the extended magneto-hydrodynamic (MHD) model in NIMROD. Our purpose is to investigate the physical cause behind edge localized mode (ELM) suppression in experiment after the Li-coating of the divertor and the first wall of the NSTX tokamak. Besides ideal MHD modeling, including finite-Larmor radius effect and two-fluid Hall and electron diamagnetic drift contributions, a non-ideal resistivity model is employed, taking into account the increase of Z eff after Li-conditioning in ELM-free H-mode. And unlike an earlier conclusion from anmore » eigenvalue code analysis of these equilibria, NIMROD results find that after reduced recycling from divertor plates, profile modification is necessary but insufficient to explain the mechanism behind complete ELMs suppression in ideal two-fluid MHD. After considering the higher plasma resistivity due to higher Z eff, the complete stabilization could be explained. Furthermore, a thorough analysis of both pre-lithium ELMy and with-lithium ELM-free cases using ideal and non-ideal MHD models is presented, after accurately including a vacuum-like cold halo region in NIMROD to investigate ELMs.« less

  15. Understanding tungsten divertor sourcing and SOL transport using multiple poloidally-localized sources in DIII-D ELM-y H-mode discharges

    NASA Astrophysics Data System (ADS)

    Unterberg, Ea; Donovan, D.; Barton, J.; Wampler, Wr; Abrams, T.; Thomas, Dm; Petrie, T.; Guo, Hy; Stangeby, Pg; Elder, Jd; Rudakov, D.; Grierson, B.; Victor, B.

    2017-10-01

    Experiments using metal inserts with novel isotopically-enriched tungsten coatings at the outer divertor strike point (OSP) have provided unique insight into the ELM-induced sourcing, main-SOL transport, and core accumulation control mechanisms of W for a range of operating conditions. This experimental approach has used a multi-head, dual-facing collector probe (CP) at the outboard midplane, as well as W-I and core W spectroscopy. Using the CP system, the total amount of W deposited relative to source measurements shows a clear dependence on ELM size, ELM frequency, and strike point location, with large ELMs depositing significantly more W on the CP from the far-SOL source. Additionally, high spatial ( 1mm) and ELM resolved spectroscopic measurements of W sourcing indicate shifts in the peak erosion rate. Furthermore, high performance discharges with rapid ELMs show core W concentrations of few 10-5, and the CP deposition profile indicates W is predominantly transported to the midplane from the OSP rather than from the far-SOL region. The low central W concentration is shown to be due to flattening of the main plasma density profile, presumably by on-axis electron cyclotron heating. Work supported under USDOE Cooperative Agreement DE-FC02-04ER54698.

  16. Virtual screening by a new Clustering-based Weighted Similarity Extreme Learning Machine approach

    PubMed Central

    Kudisthalert, Wasu

    2018-01-01

    Machine learning techniques are becoming popular in virtual screening tasks. One of the powerful machine learning algorithms is Extreme Learning Machine (ELM) which has been applied to many applications and has recently been applied to virtual screening. We propose the Weighted Similarity ELM (WS-ELM) which is based on a single layer feed-forward neural network in a conjunction of 16 different similarity coefficients as activation function in the hidden layer. It is known that the performance of conventional ELM is not robust due to random weight selection in the hidden layer. Thus, we propose a Clustering-based WS-ELM (CWS-ELM) that deterministically assigns weights by utilising clustering algorithms i.e. k-means clustering and support vector clustering. The experiments were conducted on one of the most challenging datasets–Maximum Unbiased Validation Dataset–which contains 17 activity classes carefully selected from PubChem. The proposed algorithms were then compared with other machine learning techniques such as support vector machine, random forest, and similarity searching. The results show that CWS-ELM in conjunction with support vector clustering yields the best performance when utilised together with Sokal/Sneath(1) coefficient. Furthermore, ECFP_6 fingerprint presents the best results in our framework compared to the other types of fingerprints, namely ECFP_4, FCFP_4, and FCFP_6. PMID:29652912

  17. Plant signals during beetle (Scolytus multistriatus) feeding in American elm (Ulmus americana Planch)

    PubMed Central

    Saremba, Brett M.; Tymm, Fiona J. M.; Baethke, Kathy; Rheault, Mark R.; Sherif, Sherif M.; Saxena, Praveen K.; Murch, Susan J.

    2017-01-01

    ABSTRACT American Elms were devastated by an outbreak of Dutch Elm Disease is caused by the fungus Ophiostoma novo-ulmi Brasier that originated in Asia and arrived in the early 1900s. In spite of decades of study, the specific mechanisms and disease resistance in some trees is not well understood. the fungus is spread by several species of bark beetles in the genus Scolytus, during their dispersal and feeding. Our objective was to understand elm responses to beetle feeding in the absence of the fungus to identify potential resistance mechanisms. A colony of Scolytus multistriatus was established from wild-caught beetles and beetles were co-incubated with susceptible or resistant American elm varieties in a controlled environment chamber. Beetles burrowed into the auxillary meristems of the young elm shoots. The trees responded to the beetle damage by a series of spikes in the concentration of plant growth regulating compounds, melatonin, serotonin, and jasmonic acid. Spikes in melatonin and serotonin represented a 7,000-fold increase over resting levels. Spikes in jasmonic acid were about 10-fold higher than resting levels with one very large spike observed. Differences were noted between susceptible and resistant elms that provide new understanding of plant defenses. PMID:28448744

  18. Rad53 regulates replication fork restart after DNA damage in Saccharomyces cerevisiae

    PubMed Central

    Szyjka, Shawn J.; Aparicio, Jennifer G.; Viggiani, Christopher J.; Knott, Simon; Xu, Weihong; Tavaré, Simon; Aparicio, Oscar M.

    2008-01-01

    Replication fork stalling at a DNA lesion generates a damage signal that activates the Rad53 kinase, which plays a vital role in survival by stabilizing stalled replication forks. However, evidence that Rad53 directly modulates the activity of replication forks has been lacking, and the nature of fork stabilization has remained unclear. Recently, cells lacking the Psy2–Pph3 phosphatase were shown to be defective in dephosphorylation of Rad53 as well as replication fork restart after DNA damage, suggesting a mechanistic link between Rad53 deactivation and fork restart. To test this possibility we examined the progression of replication forks in methyl-methanesulfonate (MMS)-damaged cells, under different conditions of Rad53 activity. Hyperactivity of Rad53 in pph3Δ cells slows fork progression in MMS, whereas deactivation of Rad53, through expression of dominant-negative Rad53-KD, is sufficient to allow fork restart during recovery. Furthermore, combined deletion of PPH3 and PTC2, a second, unrelated Rad53 phosphatase, results in complete replication fork arrest and lethality in MMS, demonstrating that Rad53 deactivation is a key mechanism controlling fork restart. We propose a model for regulation of replication fork progression through damaged DNA involving a cycle of Rad53 activation and deactivation that coordinates replication restart with DNA repair. PMID:18628397

  19. 23. View of Clark Fork Vehicle Bridge facing upwest side. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    23. View of Clark Fork Vehicle Bridge facing up-west side. Looking at structural connection of top chord, vertical laced channel and diagonal bars. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  20. 13. View of Clark Fork Vehicle Bridge facing south. Concrete ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. View of Clark Fork Vehicle Bridge facing south. Concrete barrier blocks access. Plaque was originally located where strioed traffic sign is posted at right. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  1. 12. View of Clark Fork Vehicle Bridge facing south. Approach ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    12. View of Clark Fork Vehicle Bridge facing south. Approach from the north road. Plaque was originally located where striped traffic sign is posted. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  2. Detection of tumor cell-specific mRNA and protein in exosome-like microvesicles from blood and saliva.

    PubMed

    Yang, Jieping; Wei, Fang; Schafer, Christopher; Wong, David T W

    2014-01-01

    The discovery of disease-specific biomarkers in oral fluids has revealed a new dimension in molecular diagnostics. Recent studies have reported the mechanistic involvement of tumor cells derived mediators, such as exosomes, in the development of saliva-based mRNA biomarkers. To further our understanding of the origins of disease-induced salivary biomarkers, we here evaluated the hypothesis that tumor-shed secretory lipidic vesicles called exosome-like microvesicles (ELMs) that serve as protective carriers of tissue-specific information, mRNAs, and proteins, throughout the vasculature and bodily fluids. RNA content was analyzed in cell free-saliva and ELM-enriched fractions of saliva. Our data confirmed that the majority of extracellular RNAs (exRNAs) in saliva were encapsulated within ELMs. Nude mice implanted with human lung cancer H460 cells expressing hCD63-GFP were used to follow the circulation of tumor cell specific protein and mRNA in the form of ELMs in vivo. We were able to identify human GAPDH mRNA in ELMs of blood and saliva of tumor bearing mice using nested RT-qPCR. ELMs positive for hCD63-GFP were detected in the saliva and blood of tumor bearing mice as well as using electric field-induced release and measurement (EFIRM). Altogether, our results demonstrate that ELMs carry tumor cell-specific mRNA and protein from blood to saliva in a xenografted mouse model of human lung cancer. These results therefore strengthen the link between distal tumor progression and the biomarker discovery of saliva through the ELMs.

  3. Theory-based model for the pedestal, edge stability and ELMs in tokamaks

    NASA Astrophysics Data System (ADS)

    Pankin, A. Y.; Bateman, G.; Brennan, D. P.; Schnack, D. D.; Snyder, P. B.; Voitsekhovitch, I.; Kritz, A. H.; Janeschitz, G.; Kruger, S.; Onjun, T.; Pacher, G. W.; Pacher, H. D.

    2006-04-01

    An improved model for triggering edge localized mode (ELM) crashes is developed for use within integrated modelling simulations of the pedestal and ELM cycles at the edge of H-mode tokamak plasmas. The new model is developed by using the BALOO, DCON and ELITE ideal MHD stability codes to derive parametric expressions for the ELM triggering threshold. The whole toroidal mode number spectrum is studied with these codes. The DCON code applies to low mode numbers, while the BALOO code applies to only high mode numbers and the ELITE code applies to intermediate and high mode numbers. The variables used in the parametric stability expressions are the normalized pressure gradient and the parallel current density, which drive ballooning and peeling modes. Two equilibria motivated by DIII-D geometry with different plasma triangularities are studied. It is found that the stable region in the high triangularity discharge covers a much larger region of parameter space than the corresponding stability region in the low triangularity discharge. The new ELM trigger model is used together with a previously developed model for pedestal formation and ELM crashes in the ASTRA integrated modelling code to follow the time evolution of the temperature profiles during ELM cycles. The ELM frequencies obtained in the simulations of low and high triangularity discharges are observed to increase with increasing heating power. There is a transition from second stability to first ballooning mode stability as the heating power is increased in the high triangularity simulations. The results from the ideal MHD stability codes are compared with results from the resistive MHD stability code NIMROD.

  4. Fork rotation and DNA precatenation are restricted during DNA replication to prevent chromosomal instability.

    PubMed

    Schalbetter, Stephanie A; Mansoubi, Sahar; Chambers, Anna L; Downs, Jessica A; Baxter, Jonathan

    2015-08-18

    Faithful genome duplication and inheritance require the complete resolution of all intertwines within the parental DNA duplex. This is achieved by topoisomerase action ahead of the replication fork or by fork rotation and subsequent resolution of the DNA precatenation formed. Although fork rotation predominates at replication termination, in vitro studies have suggested that it also occurs frequently during elongation. However, the factors that influence fork rotation and how rotation and precatenation may influence other replication-associated processes are unknown. Here we analyze the causes and consequences of fork rotation in budding yeast. We find that fork rotation and precatenation preferentially occur in contexts that inhibit topoisomerase action ahead of the fork, including stable protein-DNA fragile sites and termination. However, generally, fork rotation and precatenation are actively inhibited by Timeless/Tof1 and Tipin/Csm3. In the absence of Tof1/Timeless, excessive fork rotation and precatenation cause extensive DNA damage following DNA replication. With Tof1, damage related to precatenation is focused on the fragile protein-DNA sites where fork rotation is induced. We conclude that although fork rotation and precatenation facilitate unwinding in hard-to-replicate contexts, they intrinsically disrupt normal chromosome duplication and are therefore restricted by Timeless/Tipin.

  5. Improved Sanitation Practice for Control of Dutch Elm Disease

    Treesearch

    Jack H. Barger

    1977-01-01

    In Detroit, Michigan, 12 plots, each containing about 600 American elm trees, Ulmus americana L., were subjected for 3 years to intensive and conventional sanitation treatments to control Dutch elm disease. In the intensive treatment, three disease surveys were conducted each year; each followed by tree removal within 20 working days. In the...

  6. Bringing Interpretability and Visualization with Artificial Neural Networks

    ERIC Educational Resources Information Center

    Gritsenko, Andrey

    2017-01-01

    Extreme Learning Machine (ELM) is a training algorithm for Single-Layer Feed-forward Neural Network (SLFN). The difference in theory of ELM from other training algorithms is in the existence of explicitly-given solution due to the immutability of initialed weights. In practice, ELMs achieve performance similar to that of other state-of-the-art…

  7. Semiochemical-MediatedFlight Strategies of Two Invasive Elm Bark Beetles: A Potential Factor in Competitive Displacement

    USDA-ARS?s Scientific Manuscript database

    A recent seven-state survey revealed that the newly invasive banded elm bark beetle, Scolytus schevyrewi, was abundant in areas of Colorado and Wyoming, USA, whereas the long-established European elm bark beetle, S. multistriatus was not as abundant. Behavioral trials were conducted by hanging sm...

  8. Genome size variation in elms (Ulmus spp.) and related genera

    USDA-ARS?s Scientific Manuscript database

    The elms (the genus Ulmus) are one of the most important tree crops for the $4.7-billion per year U.S. nursery industry. Utilization of these plants has been limited in recent decades by diseases introduced from the Old World, especially Dutch elm disease. Past research and breeding have been based ...

  9. Scaling Relationships for ELM Diverter Heat Flux on DIII D

    NASA Astrophysics Data System (ADS)

    Peters, E. A.; Makowski, M. A.; Leonard, A. W.

    2015-11-01

    Edge Localized Modes (ELMs) are periodic plasma instabilities that occur during H-mode operation in tokamaks. Left unmitigated, these instabilities result in concentrated particle and heat fluxes at the divertor and stand to cause serious damage to the plasma facing components of tokamaks. The purpose of this research is to find scaling relationships that predict divertor heat flux due to ELMs based on plasma parameters at the time of instability. This will be accomplished by correlating characteristic ELM parameters with corresponding plasma measurements and analyzing the data for trends. One early assessment is the effect of the heat transmission coefficient ? on the in/out asymmetry of the calculated ELM heat fluxes. Using IR camera data, further assessments in this study will continue to emphasize in/out asymmetry in ELMs, as this has important implications for ITER operation. Work supported in part by the US DOE, DE-AC52-07NA27344, DE-FC02-04ER54698, Office of Workforce Development for Teachers and Scientists (WDTS) under the Science Undergraduate Laboratory Internships Program (SULI).

  10. Deep Convolutional Extreme Learning Machine and Its Application in Handwritten Digit Classification

    PubMed Central

    Yang, Xinyi

    2016-01-01

    In recent years, some deep learning methods have been developed and applied to image classification applications, such as convolutional neuron network (CNN) and deep belief network (DBN). However they are suffering from some problems like local minima, slow convergence rate, and intensive human intervention. In this paper, we propose a rapid learning method, namely, deep convolutional extreme learning machine (DC-ELM), which combines the power of CNN and fast training of ELM. It uses multiple alternate convolution layers and pooling layers to effectively abstract high level features from input images. Then the abstracted features are fed to an ELM classifier, which leads to better generalization performance with faster learning speed. DC-ELM also introduces stochastic pooling in the last hidden layer to reduce dimensionality of features greatly, thus saving much training time and computation resources. We systematically evaluated the performance of DC-ELM on two handwritten digit data sets: MNIST and USPS. Experimental results show that our method achieved better testing accuracy with significantly shorter training time in comparison with deep learning methods and other ELM methods. PMID:27610128

  11. KSC-08pd2916

    NASA Image and Video Library

    2008-09-24

    CAPE CANAVERAL, Fla. - On the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida, ramps are in place for the offloading of the primary cargo from the Russian Antonov AH-124-100 cargo airplane. The plane carries the final components of the Japan Aerospace Exploration Agency's Kibo laboratory for the International Space Station: the Kibo Exposed Facility, or EF, and the Experiment Logistics Module Exposed Section, or ELM-ES. The EF provides a multipurpose platform where science experiments can be deployed and operated in the exposed environment. The payloads attached to the EF can be exchanged or retrieved by Kibo's robotic arm, the JEM Remote Manipulator System. The ELM-ES will be attached to the end of the EF to provide payload storage space and can carry up to three payloads at launch. In addition, the ELM-ES provides a logistics function where it can be detached from the EF and returned to the ground aboard the space shuttle. The two JEM components will be carried aboard space shuttle Endeavour on the STS-127 mission targeted for launch in May 2009. Photo credit: NASA/Jim Grossmann

  12. KSC-08pd2915

    NASA Image and Video Library

    2008-09-24

    CAPE CANAVERAL, Fla. - On the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida, workers remove material from a cargo box before offloading the primary cargo from the Russian Antonov AH-124-100 cargo airplane. The plane carries the final components of the Japan Aerospace Exploration Agency's Kibo laboratory for the International Space Station: the Kibo Exposed Facility, or EF, and the Experiment Logistics Module Exposed Section, or ELM-ES. The EF provides a multipurpose platform where science experiments can be deployed and operated in the exposed environment. The payloads attached to the EF can be exchanged or retrieved by Kibo's robotic arm, the JEM Remote Manipulator System. The ELM-ES will be attached to the end of the EF to provide payload storage space and can carry up to three payloads at launch. In addition, the ELM-ES provides a logistics function where it can be detached from the EF and returned to the ground aboard the space shuttle. The two JEM components will be carried aboard space shuttle Endeavour on the STS-127 mission targeted for launch in May 2009. Photo credit: NASA/Jim Grossmann

  13. KSC-08pd2914

    NASA Image and Video Library

    2008-09-24

    CAPE CANAVERAL, Fla. - On the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida, equipment is removed from the Russian Antonov AH-124-100 cargo airplane to facilitate offloading of the primary cargo, the final components of the Japan Aerospace Exploration Agency's Kibo laboratory for the International Space Station. The components are the Kibo Exposed Facility, or EF, and the Experiment Logistics Module Exposed Section, or ELM-ES. The EF provides a multipurpose platform where science experiments can be deployed and operated in the exposed environment. The payloads attached to the EF can be exchanged or retrieved by Kibo's robotic arm, the JEM Remote Manipulator System. The ELM-ES will be attached to the end of the EF to provide payload storage space and can carry up to three payloads at launch. In addition, the ELM-ES provides a logistics function where it can be detached from the EF and returned to the ground aboard the space shuttle. The two JEM components will be carried aboard space shuttle Endeavour on the STS-127 mission targeted for launch in May 2009. Photo credit: NASA/Jim Grossmann

  14. Deep Convolutional Extreme Learning Machine and Its Application in Handwritten Digit Classification.

    PubMed

    Pang, Shan; Yang, Xinyi

    2016-01-01

    In recent years, some deep learning methods have been developed and applied to image classification applications, such as convolutional neuron network (CNN) and deep belief network (DBN). However they are suffering from some problems like local minima, slow convergence rate, and intensive human intervention. In this paper, we propose a rapid learning method, namely, deep convolutional extreme learning machine (DC-ELM), which combines the power of CNN and fast training of ELM. It uses multiple alternate convolution layers and pooling layers to effectively abstract high level features from input images. Then the abstracted features are fed to an ELM classifier, which leads to better generalization performance with faster learning speed. DC-ELM also introduces stochastic pooling in the last hidden layer to reduce dimensionality of features greatly, thus saving much training time and computation resources. We systematically evaluated the performance of DC-ELM on two handwritten digit data sets: MNIST and USPS. Experimental results show that our method achieved better testing accuracy with significantly shorter training time in comparison with deep learning methods and other ELM methods.

  15. ELM Behavior in High- βp EAST-Demonstration Plasmas on DIII-D

    NASA Astrophysics Data System (ADS)

    Li, G. Q.; Gong, X. Z.; Garofalo, A. M.; Lao, L. L.; Meneghini, O.; Snyder, P. B.; Ren, Q. L.; Ding, S. Y.; Guo, W. F.; Qian, J. P.; Wan, B. N.; Xu, G. S.; Holcomb, C. T.; Solomon, W. M.

    2015-11-01

    In the DIII-D high- βp EAST-demonstration experiment, for several similar discharges when the experimental parameters such as the toroidal magnetic field or ECH power are varied slightly, the changes in ELM frequency response are observed to be much larger. Kinetic EFIT equilibrium reconstructions for these discharges have been performed, which suggest that the ELM frequency changes are likely due to the variations of pedestal width, height, and edge current density. Kinetic profile analyses further indicate that the strong ITB that are located at large minor radii (rho=0.6 ~0.7) in these discharges are affecting the pedestal structure. The ITB could broaden the pedestal width and decrease the pedestal height, thus changing the ELM frequency and size. With the GATO and ELITE MHD codes, the linear growth rates and mode structures of these ELMs are analyzed. The impact of ITB on the ELMs behavior will be discussed. Work supported by China MOST under 2014GB106001 and 2015GB102001 and US DOE under DE-FC02-04ER54698 and DE-FG03-95ER54309.

  16. Broadening of divertor heat flux profile with increasing number of ELM filaments in NSTX

    DOE PAGES

    Ahn, J. -W.; Maingi, R.; Canik, J. M.; ...

    2014-11-13

    Edge localized modes (ELMs) represent a challenge to future fusion devices, owing to cyclical high peak heat fluxes on divertor plasma facing surfaces. One ameliorating factor has been that the heat flux characteristic profile width has been observed to broaden with the size of the ELM, as compared with the inter-ELM heat flux profile. In contrast, the heat flux profile has been observed to narrow during ELMs under certain conditions in NSTX. Here we show that the ELM heat flux profile width increases with the number of filamentary striations observed, i.e., profile narrowing is observed with zero or very fewmore » striations. Because NSTX often lies on the long wavelength current-driven mode side of ideal MHD instabilities, few filamentary structures can be expected under many conditions. Lastly, ITER is also projected to lie on the current driven low-n stability boundary, and therefore detailed projections of the unstable modes expected in ITER and the heat flux driven in ensuing filamentary structures is needed.« less

  17. 14. View of Clark Fork Vehicle Bridge facing north. Approach ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. View of Clark Fork Vehicle Bridge facing north. Approach from the south. Concrete barrier blocks access. Plaque was originally located where striped traffic sign is posted at right. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  18. 40 CFR 131.33 - Idaho.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Creek, Doe Creek, Duck Creek, East Fork Holy Terror Creek, Fawn Creek, Flume Creek, Fly Creek, Forge... Terror Creek, J Fell Creek, Jacobs Ladder Creek, Lewis Creek, Liberty Creek, Lick Creek, Lime Creek... Creek, South Fork Chamberlain Creek, South Fork Holy Terror Creek, South Fork Norton Creek, South Fork...

  19. 40 CFR 131.33 - Idaho.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Creek, Doe Creek, Duck Creek, East Fork Holy Terror Creek, Fawn Creek, Flume Creek, Fly Creek, Forge... Terror Creek, J Fell Creek, Jacobs Ladder Creek, Lewis Creek, Liberty Creek, Lick Creek, Lime Creek... Creek, South Fork Chamberlain Creek, South Fork Holy Terror Creek, South Fork Norton Creek, South Fork...

  20. 40 CFR 131.33 - Idaho.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Creek, Doe Creek, Duck Creek, East Fork Holy Terror Creek, Fawn Creek, Flume Creek, Fly Creek, Forge... Terror Creek, J Fell Creek, Jacobs Ladder Creek, Lewis Creek, Liberty Creek, Lick Creek, Lime Creek... Creek, South Fork Chamberlain Creek, South Fork Holy Terror Creek, South Fork Norton Creek, South Fork...

  1. 40 CFR 131.33 - Idaho.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Creek, Doe Creek, Duck Creek, East Fork Holy Terror Creek, Fawn Creek, Flume Creek, Fly Creek, Forge... Terror Creek, J Fell Creek, Jacobs Ladder Creek, Lewis Creek, Liberty Creek, Lick Creek, Lime Creek... Creek, South Fork Chamberlain Creek, South Fork Holy Terror Creek, South Fork Norton Creek, South Fork...

  2. 40 CFR 131.33 - Idaho.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Creek, Doe Creek, Duck Creek, East Fork Holy Terror Creek, Fawn Creek, Flume Creek, Fly Creek, Forge... Terror Creek, J Fell Creek, Jacobs Ladder Creek, Lewis Creek, Liberty Creek, Lick Creek, Lime Creek... Creek, South Fork Chamberlain Creek, South Fork Holy Terror Creek, South Fork Norton Creek, South Fork...

  3. ELM mitigation techniques

    NASA Astrophysics Data System (ADS)

    Evans, T. E.

    2013-07-01

    Large edge-localized mode (ELM) control techniques must be developed to help ensure the success of burning and ignited fusion plasma devices such as tokamaks and stellarators. In full performance ITER tokamak discharges, with QDT = 10, the energy released by a single ELM could reach ˜30 MJ which is expected to result in an energy density of 10-15 MJ/m2on the divertor targets. This will exceed the estimated divertor ablation limit by a factor of 20-30. A worldwide research program is underway to develop various types of ELM control techniques in preparation for ITER H-mode plasma operations. An overview of the ELM control techniques currently being developed is discussed along with the requirements for applying these techniques to plasmas in ITER. Particular emphasis is given to the primary approaches, pellet pacing and resonant magnetic perturbation fields, currently being considered for ITER.

  4. Reconnaissance Geologic Map of the Hayfork 15' Quadrangle, Trinity County, California

    USGS Publications Warehouse

    Irwin, William P.

    2010-01-01

    The Hayfork 15' quadrangle is located just west of the Weaverville 15' quadrangle in the southern part of the Klamath Mountains geologic province of northern California. It spans parts of six generally north-northwest-trending tectonostratigraphic terranes that are, from east to west, the Eastern Klamath, Central Metamorphic, North Fork, Eastern Hayfork, Western Hayfork, and Rattlesnake Creek terranes. Remnants of a once-widespread postaccretionary overlap assemblage, the Cretaceous Great Valley sequence, crop out at three localities in the southern part of the Hayfork quadrangle. The Tertiary fluvial and lacustrine Weaverville Formation occupies a large, shallow, east-northeast-trending graben in the south half of the quadrangle. The small area of Eastern Klamath terrane is part of the Oregon Mountain outlier, which is more widely exposed to the east in the Weaverville 15' quadrangle. It was originally mapped as a thrust plate of Bragdon(?) Formation, but it is now thought by some to be part of an outlier of Yreka terrane that has been dislocated 60 km southward by the La Grange Fault. The Central Metamorphic terrane, which forms the footwall of the La Grange Fault, was formed by the eastward subduction of oceanic crustal basalt (the Salmon Hornblende Schist) and its overlying siliceous sediments with interbedded limestone (the Abrams Mica Schist) beneath the Eastern Klamath terrane. Rb-Sr analysis of the Abrams Mica Schist indicates a Middle Devonian metamorphic age of approximately 380 Ma, which probably represents the age of subduction. The North Fork terrane, which is faulted against the western boundary of the Central Metamorphic terrane, consists of the Permian(?) North Fork ophiolite and overlying broken formation and melange of Permian to Early Jurassic (Pliensbachian) marine metasedimentary and metavolcanic rocks. The ophiolite, which crops out along the western border of the terrane, is thrust westward over the Eastern Hayfork terrane. The Eastern Hayfork terrane is a broken formation and melange of volcanic and sedimentary rocks, including chert and blocks of amphibolite, limestone, and serpentinized ultramafic rocks. The chert contains radiolarians of Permian and Triassic ages, but none of clearly Jurassic age. In contrast, the cherts of the North Fork terrane contain Early and Middle Jurassic radiolarians in addition to those of Permian and Triassic ages; also, some limestones of the Eastern Hayfork terrane contain fossil faunas of Tethyan affinity, but those of the North Fork terrane do not. The Western Hayfork terrane is an andesitic volcanic arc that was accreted to the Eastern Hayfork terrane. It consists mainly of metavolcaniclastic andesitic agglomerate and tuff, as well as argillite and chert, and it includes the dioritic Ironside Mountain batholith, which intruded during Middle Jurassic time. Two large patches of Western Hayfork terrane mapped in the central part of the Eastern Hayfork terrane may be exposed through windows in the Eastern Hayfork terrane, although the structural relation is not clear. The Rattlesnake Creek terrane is a melange that occupies only a small area in the southwest corner of the Hayfork quadrangle; however, it is a major unit in the Hyampom 15' quadrangle to the west. It consists mainly of broken and sheared ophiolitic rocks of probable Permian or early Mesozoic age. The Cretaceous Great Valley sequence overlap assemblage here postdates the Early Cretaceous (approximately 136 Ma) emplacement of the Shasta Bally batholith, which is widely exposed to the east in the Weaverville 15' quadrangle. The Great Valley sequence once covered much of the southern Klamath Mountains; however, in the Hayfork quadrangle, only three small patches remain near its southern boundary. Weakly consolidated nonmarine sedimentary rocks of the Weaverville Formation of mid-Tertiary age, which contain abundant fossil plants, occupy a large, shallow, east-northeast-trending graben

  5. Divertor, scrape-off layer and pedestal particle dynamics in the ELM cycle on ASDEX Upgrade

    NASA Astrophysics Data System (ADS)

    Laggner, F. M.; Keerl, S.; Gnilsen, J.; Wolfrum, E.; Bernert, M.; Carralero, D.; Guimarais, L.; Nikolaeva, V.; Potzel, S.; Cavedon, M.; Mink, F.; Dunne, M. G.; Birkenmeier, G.; Fischer, R.; Viezzer, E.; Willensdorfer, M.; Wischmeier, M.; Aumayr, F.; the EUROfusion MST1 Team; the ASDEX Upgrade Team

    2018-02-01

    In addition to the relaxation of the pedestal, edge localised modes (ELMs) introduce changes to the divertor and scrape-off layer (SOL) conditions. Their impact on the inter-ELM pedestal recovery is investigated, with emphasis on the electron density (n e) evolution. The typical ELM cycle occurring in an exemplary ASDEX Upgrade discharge interval at moderate applied gas puff and heating power is characterised, utilising several divertor, SOL and pedestal diagnostics. In the studied discharge interval the inner divertor target is detached before the ELM crash, while the outer target is attached. The particles and power expelled by the ELM crash lead to a re-attachment of the inner target plasma. After the ELM crash, the outer divertor target moves into a high recycling regime with large n e in front of the plate, which is accompanied by high main chamber neutral fluxes. On similar timescales, the inner target fully detaches and the high field side high density region (HFSHD) is formed reaching up to the high field side midplane. This state evolves again to the pre-ELM state, when the main chamber neutral fluxes are reduced later in the ELM cycle. Neither the timescale of the appearance of the HFSHD nor the increase of the main chamber neutral fluxes fit the timescale of the n e pedestal, which is faster. It is found that during the n e pedestal recovery, the magnetic activity at the low field side midplane is strongly reduced indicating a lower level of fluctuations. A rough estimation of the particle flux across the pedestal suggests that the particle flux is reduced in this period. In conclusion, the evolution of the n e pedestal is determined by a combination of neutral fluxes, HFSHD and reduced particle flux across the pedestal. A reduced particle flux explains the fast, experimentally observed re-establishment of the n e pedestal best, whereas neutrals and HFSHD impact on the evolution of the SOL and separatrix conditions.

  6. Validation of the model for ELM suppression with 3D magnetic fields using low torque ITER baseline scenario discharges in DIII-D

    NASA Astrophysics Data System (ADS)

    Moyer, R. A.; Paz-Soldan, C.; Nazikian, R.; Orlov, D. M.; Ferraro, N. M.; Grierson, B. A.; Knölker, M.; Lyons, B. C.; McKee, G. R.; Osborne, T. H.; Rhodes, T. L.; Meneghini, O.; Smith, S.; Evans, T. E.; Fenstermacher, M. E.; Groebner, R. J.; Hanson, J. M.; La Haye, R. J.; Luce, T. C.; Mordijck, S.; Solomon, W. M.; Turco, F.; Yan, Z.; Zeng, L.; DIII-D Team

    2017-10-01

    Experiments have been executed in the DIII-D tokamak to extend suppression of Edge Localized Modes (ELMs) with Resonant Magnetic Perturbations (RMPs) to ITER-relevant levels of beam torque. The results support the hypothesis for RMP ELM suppression based on transition from an ideal screened response to a tearing response at a resonant surface that prevents expansion of the pedestal to an unstable width [Snyder et al., Nucl. Fusion 51, 103016 (2011) and Wade et al., Nucl. Fusion 55, 023002 (2015)]. In ITER baseline plasmas with I/aB = 1.4 and pedestal ν * ˜ 0.15, ELMs are readily suppressed with co- I p neutral beam injection. However, reducing the beam torque from 5 Nm to ≤ 3.5 Nm results in loss of ELM suppression and a shift in the zero-crossing of the electron perpendicular rotation ω ⊥ e ˜ 0 deeper into the plasma. The change in radius of ω ⊥ e ˜ 0 is due primarily to changes to the electron diamagnetic rotation frequency ωe * . Linear plasma response modeling with the resistive MHD code m3d-c1 indicates that the tearing response location tracks the inward shift in ω ⊥ e ˜ 0. At pedestal ν * ˜ 1, ELM suppression is also lost when the beam torque is reduced, but the ω ⊥ e change is dominated by collapse of the toroidal rotation v T . The hypothesis predicts that it should be possible to obtain ELM suppression at reduced beam torque by also reducing the height and width of the ωe * profile. This prediction has been confirmed experimentally with RMP ELM suppression at 0 Nm of beam torque and plasma normalized pressure β N ˜ 0.7. This opens the possibility of accessing ELM suppression in low torque ITER baseline plasmas by establishing suppression at low beta and then increasing beta while relying on the strong RMP-island coupling to maintain suppression.

  7. ELM - A SIMPLE TOOL FOR THERMAL-HYDRAULIC ANALYSIS OF SOLID-CORE NUCLEAR ROCKET FUEL ELEMENTS

    NASA Technical Reports Server (NTRS)

    Walton, J. T.

    1994-01-01

    ELM is a simple computational tool for modeling the steady-state thermal-hydraulics of propellant flow through fuel element coolant channels in nuclear thermal rockets. Written for the nuclear propulsion project of the Space Exploration Initiative, ELM evaluates the various heat transfer coefficient and friction factor correlations available for turbulent pipe flow with heat addition. In the past, these correlations were found in different reactor analysis codes, but now comparisons are possible within one program. The logic of ELM is based on the one-dimensional conservation of energy in combination with Newton's Law of Cooling to determine the bulk flow temperature and the wall temperature across a control volume. Since the control volume is an incremental length of tube, the corresponding pressure drop is determined by application of the Law of Conservation of Momentum. The size, speed, and accuracy of ELM make it a simple tool for use in fuel element parametric studies. ELM is a machine independent program written in FORTRAN 77. It has been successfully compiled on an IBM PC compatible running MS-DOS using Lahey FORTRAN 77, a DEC VAX series computer running VMS, and a Sun4 series computer running SunOS UNIX. ELM requires 565K of RAM under SunOS 4.1, 360K of RAM under VMS 5.4, and 406K of RAM under MS-DOS. Because this program is machine independent, no executable is provided on the distribution media. The standard distribution medium for ELM is one 5.25 inch 360K MS-DOS format diskette. ELM was developed in 1991. DEC, VAX, and VMS are trademarks of Digital Equipment Corporation. Sun4 and SunOS are trademarks of Sun Microsystems, Inc. IBM PC is a registered trademark of International Business Machines. MS-DOS is a registered trademark of Microsoft Corporation.

  8. Confirmatory Factor Analysis of the Trinity Inventory of Precursors to Suicide (TIPS) and Its Relationship to Hopelessness and Depression

    ERIC Educational Resources Information Center

    Smyth, Caroline L.; MacLachlan, Malcolm

    2005-01-01

    Numerous existing measures assess attitudes toward suicide yet fail to account for contextual factors. The Trinity Inventory of Precursors to Suicide (TIPS) is presented as an alternative, with implications for the development of prevention programs. Having previously reported exploratory analysis of the TIPS; confirmatory factor analysis and…

  9. 77 FR 69789 - Foreign-Trade Zone 171-Liberty County, TX; Application for Reorganization/Expansion Under...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-21

    ..., Cleveland; Site 2 (45 acres)-- Port of Liberty County Industrial Park located on Trinity River, Liberty; Site 3 (27 acres)--Port of Liberty County Industrial Park located on the Trinity River some 2 miles..., Highway FM 787, Liberty; Site 5 (583.081 acres)--Sjolander Plastics Storage Railyard facility, adjacent to...

  10. Access to NMR Spectroscopy for Two-Year College Students: The NMR Site at Trinity University

    ERIC Educational Resources Information Center

    Mills, Nancy S.; Shanklin, Michael

    2011-01-01

    Students at two-year colleges and small four-year colleges have often obtained their exposure to NMR spectroscopy through "canned" spectra because the cost of an NMR spectrometer, particularly a high-field spectrometer, is prohibitive in these environments. This article describes the design of a NMR site at Trinity University in which…

  11. 78 FR 51741 - Notice of Application for Withdrawal and Opportunity for Public Meeting; California

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-21

    ... approximately 541 acres of National Forest System lands in the Shasta-Trinity National Forest for a period of 20..., Shasta-Trinity National Forest Headquarters, 530-226-2500 during regular business hours, 8 a.m. to 4:30 p... County, California. The above-described lands being National Forest System lands, the Secretary shall...

  12. Modeling water-quality loads to the reservoirs of the Upper Trinity River Basin, Texas, USA

    USDA-ARS?s Scientific Manuscript database

    Water quality modeling efforts have been conducted for 12 reservoirs in ten watersheds in Upper Trinity River Basin located in north Texas. The reservoirs are being used for water supply to the populated area around the Dallas-Fort Worth Metro and the water quality of some of these reservoirs has b...

  13. 1. INTERIOR VIEW WITH NAVE, BARREL VAULTED SOLEA, ICONOSTAS WITH ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. INTERIOR VIEW WITH NAVE, BARREL VAULTED SOLEA, ICONOSTAS WITH ICON AND SANCTUARY. IN ARCH ABOVE THE SANCTUARY IS THE TABLE OF ABRAHAM. THE ICONOSTAS INCLUDES ICONS OF THE ARCHANGEL MICHAEL, THE HOLY TRINITY, MOTHER OF GOD HOLDING THE CHRIST CHILD, JESUS. - Holy Trinity-Holy Cross Greek Orthodox Church, 200 Nineteenth Street South, Birmingham, Jefferson County, AL

  14. Breaking the Bonds of Poverty: A Motivational Profile of Selected Welfare Single Mothers Entering College.

    ERIC Educational Resources Information Center

    Cheng, Barbara Davis

    Single mothers on welfare were recruited for a program at Trinity College of Vermont using a variety of methods: newspaper advertisements, admission office applicants, and welfare office solicitation. Eligible for the program were single mothers on welfare meeting all Trinity College entrance requirements and having an interest in and commitment…

  15. Establishing a Mathematics-Enrichment Community in a Multi-School Environment

    ERIC Educational Resources Information Center

    Thomson, Ian

    2005-01-01

    Trinity College is a low-fee independent school in Gawler, South Australia. The college has an enrolment of 3500 students of varied socioeconomic mix, drawn from the northern suburbs of Adelaide. Trinity has recently been restructured into four R-10 schools and one senior school for Years 11-13. The schools share a common mathematics curriculum.…

  16. Unholy Trinity? Secularism Institute Renews Liberal Arts Curriculum

    ERIC Educational Resources Information Center

    Keysar, Ariela

    2010-01-01

    Secularism is controversial in today's political debates, championed by some and vilified by others. So when Trinity College in Hartford, Conn., opened a center for the study of secularism in September 2005, some people worried that it could become a source of friction on campus--yet another battleground in the culture wars that are wreaking havoc…

  17. 76 FR 20302 - Listing Endangered and Threatened Species; 90-Day Finding on a Petition To List Chinook Salmon

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-12

    ... a Petition To List Chinook Salmon AGENCY: National Marine Fisheries Service (NMFS), National Oceanic... salmon (Oncorhynchus tshawytscha) in the Upper Klamath and Trinity Rivers Basin as threatened or... conduct a status review of the Chinook salmon in the Upper Klamath and Trinity Rivers Basin to determine...

  18. Extreme learning machine for ranking: generalization analysis and applications.

    PubMed

    Chen, Hong; Peng, Jiangtao; Zhou, Yicong; Li, Luoqing; Pan, Zhibin

    2014-05-01

    The extreme learning machine (ELM) has attracted increasing attention recently with its successful applications in classification and regression. In this paper, we investigate the generalization performance of ELM-based ranking. A new regularized ranking algorithm is proposed based on the combinations of activation functions in ELM. The generalization analysis is established for the ELM-based ranking (ELMRank) in terms of the covering numbers of hypothesis space. Empirical results on the benchmark datasets show the competitive performance of the ELMRank over the state-of-the-art ranking methods. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Supersonic molecular beam injection effects on tokamak plasma applied non-axisymmetric magnetic perturbation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Han, Hyunsun, E-mail: hyunsun@nfri.re.kr; In, Y.; Jeon, Y. M.

    The change of tokamak plasma behavior by supersonic molecular beam injection (SMBI) was investigated by applying a three-dimensional magnetic perturbation that could suppress edge localized modes (ELMs). From the time trace of decreasing electron temperature and with increasing plasma density keeping the total confined energy constant, the SMBI seems to act as a cold pulse on the plasma. However, the ELM behaviors were changed drastically (i.e., the symptom of ELM suppression has disappeared). The plasma collisionality in the edge-pedestal region could play a role in the change of the ELM behaviors.

  20. Discovery of Three Pulsating, Mixed-atmosphere, Extremely Low-mass White Dwarf Precursors

    NASA Astrophysics Data System (ADS)

    Gianninas, A.; Curd, Brandon; Fontaine, G.; Brown, Warren R.; Kilic, Mukremin

    2016-05-01

    We report the discovery of pulsations in three mixed-atmosphere, extremely low-mass white dwarf (ELM WD, M ≤slant 0.3 M ⊙) precursors. Following the recent discoveries of pulsations in both ELM and pre-ELM WDs, we targeted pre-ELM WDs with mixed H/He atmospheres with high-speed photometry. We find significant optical variability in all three observed targets with periods in the range 320-590 s, consistent in timescale with theoretical predictions of p-mode pulsations in mixed-atmosphere ≈0.18 M ⊙ He-core pre-ELM WDs. This represents the first empirical evidence that pulsations in pre-ELM WDs can only occur if a significant amount of He is present in the atmosphere. Future, more extensive, timeseries photometry of the brightest of the three new pulsators offers an excellent opportunity to constrain the thickness of the surface H layer, which regulates the cooling timescales for ELM WDs. Based on observations obtained at the Gemini Observatory, which is operated by the Association of Universities for Research in Astronomy, Inc., under a cooperative agreement with the NSF on behalf of the Gemini partnership: the National Science Foundation (United States), the National Research Council (Canada), CONICYT (Chile), Ministerio de Ciencia, Tecnología e Innovación Productiva (Argentina), and Ministério da Ciência, Tecnologia e Inovação (Brazil).

  1. Surface EMG signals based motion intent recognition using multi-layer ELM

    NASA Astrophysics Data System (ADS)

    Wang, Jianhui; Qi, Lin; Wang, Xiao

    2017-11-01

    The upper-limb rehabilitation robot is regard as a useful tool to help patients with hemiplegic to do repetitive exercise. The surface electromyography (sEMG) contains motion information as the electric signals are generated and related to nerve-muscle motion. These sEMG signals, representing human's intentions of active motions, are introduced into the rehabilitation robot system to recognize upper-limb movements. Traditionally, the feature extraction is an indispensable part of drawing significant information from original signals, which is a tedious task requiring rich and related experience. This paper employs a deep learning scheme to extract the internal features of the sEMG signals using an advanced Extreme Learning Machine based auto-encoder (ELMAE). The mathematical information contained in the multi-layer structure of the ELM-AE is used as the high-level representation of the internal features of the sEMG signals, and thus a simple ELM can post-process the extracted features, formulating the entire multi-layer ELM (ML-ELM) algorithm. The method is employed for the sEMG based neural intentions recognition afterwards. The case studies show the adopted deep learning algorithm (ELM-AE) is capable of yielding higher classification accuracy compared to the Principle Component Analysis (PCA) scheme in 5 different types of upper-limb motions. This indicates the effectiveness and the learning capability of the ML-ELM in such motion intent recognition applications.

  2. RMP ELM Suppression in DIII-D Plasmas with ITER Similar Shapes and Collisionalities

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Evans, T.E.; Fenstermacher, M. E.; Moyer, R.A.

    2008-01-01

    Large Type-I edge localized modes (ELMs) are completely eliminated with small n = 3 resonant magnetic perturbations (RMP) in low average triangularity, = 0.26, plasmas and in ITER similar shaped (ISS) plasmas, = 0.53, with ITER relevant collisionalities ve 0.2. Significant differences in the RMP requirements and in the properties of the ELM suppressed plasmas are found when comparing the two triangularities. In ISS plasmas, the current required to suppress ELMs is approximately 25% higher than in low average triangularity plasmas. It is also found that the width of the resonant q95 window required for ELM suppression is smaller inmore » ISS plasmas than in low average triangularity plasmas. An analysis of the positions and widths of resonant magnetic islands across the pedestal region, in the absence of resonant field screening or a self-consistent plasma response, indicates that differences in the shape of the q profile may explain the need for higher RMP coil currents during ELM suppression in ISS plasmas. Changes in the pedestal profiles are compared for each plasma shape as well as with changes in the injected neutral beam power and the RMP amplitude. Implications of these results are discussed in terms of requirements for optimal ELM control coil designs and for establishing the physics basis needed in order to scale this approach to future burning plasma devices such as ITER.« less

  3. H-mode pedestal stability and ELMs in Alcator C-Mod

    NASA Astrophysics Data System (ADS)

    Mossessian, Dmitri

    2002-11-01

    For steady state H-mode operation, a relaxation mechanism is required to limit build-up of the edge gradient and impurity accumulation. The major relaxation mechanism seen on most of the existing tokamaks - large type I ELMs - drive high particle and energy fluxes that present a significant power load on the divertor plates. On Alcator C-Mod, however, type I ELMs are not observed. Instead, more benign mechanisms - EDA and small grassy ELMs - appear to drive enhanced particle transport at the edge of H-mode plasmas. Both have good energy confinement, no impurity accumulation, and are steady state. In EDA the edge relaxation mechanism is provided by a quasicoherent electromagnetic mode localized in the outer part of the pedestal. Non-linear gyrofluid and linear gyrokinetic simulations, as well as real geometry fluctuation modeling based on fluid equations show the presence of a coherent mode. Based on those results the observed mode is tentatively identified as resistive ballooning. At higher edge pressure gradient the mode is replaced by broadband fluctuations and small irregular ELMs are observed. Based on ideal MHD calculations that include effects of bootstrap current, these ELMs are identified as medium n coupled ideal peeling/ballooning modes. The stability threshold and modes structure of these modes are studied with recently developed linear MHD stability code ELITE and the results are compared with the observed dependence of the ELMs' character on pedestal parameters and plasma shape.

  4. Dissolution of salt on the east flank of the Permian Basin in the southwestern U.S.A.

    USGS Publications Warehouse

    Johnson, K.S.

    1981-01-01

    Hydrogeologic studies prove that natural dissolution of bedded salt occurs at shallow depths in many parts of the Permian Basin of the southwestern U.S.A. This is especially well-documented on the east side of the basin in study areas on the Cimarron River and Elm Fork in western Oklahoma, and on the Red River in the southeastern part of the Texas Panhandle. Four requirements for salt dissolution are: (1) a deposit of salt; (2) a supply of water unsaturated with respect to NaCl; (3) an outlet for removal of brine; and (4) energy to cause water to flow through the system. The supply of fresh groundwater in the region is recharged through permeable rocks, alluvium, terrace deposits, karstic features and fractures. Groundwater dissolves salt at depths of 10-250 m, and the resulting brine moves laterally and upward under hydrostatic pressure through caverns, fractures in disrupted rock, and clastic or carbonate aquifers until it reaches the land surface, where it forms salt plains and salt springs. In many areas, salt dissolution produces a self-perpetuating cycle: dissolution causes cavern development, followed by collapse and subsidence of overlying rock; then the resulting disrupted rock has a greater vertical permeability that allows increased water percolation and additional salt dissolution. ?? 1981.

  5. Biology of the invasive banded elm bark beetle (Coleoptera: Scolytidae) in the western United States

    Treesearch

    Jana C. Lee; Jose F. Negron; Sally J. McElwey; Livy Williams; Jeffrey J. Witcosky; John B. Popp; Steven J. Seybold

    2011-01-01

    The banded elm bark beetle, Scolytus schevyrewi Semenov (Coleoptera: Scolytidae), native to Asia, was detected in the United States in 2003, and as of 2011 it is known to occur in 28 states and four Canadian provinces. S. schevyrewi infests the same elm (Ulmus spp.) hosts as the longestablished invasive...

  6. Use of culture filtrates of Ceratocystis ulmi as a bioassay to screen for disease tolerant Ulmus americana

    Treesearch

    Paula M. Pijut; Subash C. Domir; R. Daniel Lineberger; Lawrence R. Schreiber

    1990-01-01

    Callus cultures of elm (Ulmus americana L.) derived from Dutch elm disease susceptible, intermediate-resistant, and resistant genotypes were exposed to the culture filtrates of three pathogenic isolates of Ceratocystis ulmi, the causal agent of Dutch elm disease. Callus fresh weights, cell viability, and reactions of stem cuttings...

  7. ELM-ART--An Interactive and Intelligent Web-Based Electronic Textbook

    ERIC Educational Resources Information Center

    Weber, Gerhard; Brusilovsky, Peter

    2016-01-01

    This paper present provides a broader view on ELM-ART, one of the first Web-based Intelligent Educational systems that offered a creative combination of two different paradigms--Intelligent Tutoring and Adaptive Hypermedia technologies. The unique dual nature of ELM-ART contributed to its long life and research impact and was a result of…

  8. Explaining Electronic Learning Management Systems (ELMS) Continued Usage Intentions among Facilitators in Higher Education Institutions (HEIs) in Tanzania

    ERIC Educational Resources Information Center

    Muries, Bruckse; Masele, Juma James

    2017-01-01

    This study sought to explain ELMS continued usage intentions among HEIs in Tanzania. The study was guided by main research question, "What explains ELMS continued usage intentions among facilitators in HEIs in Tanzania?" The study used descriptive cross sectional design administered to 264 respondents drawn from five universities…

  9. Co-occurrence of the invasive banded and European elm bark beetles (Coleoptera: Scolytidae) in North America

    Treesearch

    Janna C. Lee; Ingrid Aguayo; Ray Aslin; Gail Durham; Shakeeb M. Hamud; Beruce D. Moltzan; A. Steve Munson; Jose F. Negron; Travis Peterson; Iral R. Ragenovich; Jeffrey J. Witcosky; Steven J. Seybold

    2009-01-01

    The invasive European elm bark beetle, Scolytus multistriatus (Marsham), was detected in Massachusetts a century ago, and it now occurs throughout the continental United States and southern Canada. The Asian banded elm bark beetle, Scolytus schevyrewi Semenov, was discovered in the United States in 2003, and now occurs in 28 states...

  10. Challenge inoculations to test for Dutch elm disease tolerance: a summary of Methods used by various researchers

    USDA-ARS?s Scientific Manuscript database

    A variety of methods have been used by different research groups to “challenge” inoculate American elms (Ulmus americana) with the purpose of determining whether some clones may be resistant to the Dutch elm disease fungus. The methods used by seven research groups are described, along with observat...

  11. Canopy decline assessment in American elm after inoculation with different doses of Ophiostoma ulmi and O. novo-ulmi

    Treesearch

    Charles E. Flower; James M. Slavicek; Dale Lesser; Steven Eshita; Cornelia C. Pinchot

    2017-01-01

    Restoration of American elm (Ulmus americana L.) in natural and urban landscapes necessitates the development of new selections that not only exhibit Dutch elm disease (DED, caused by the fungal pathogen Ophiostoma novo-ulmi and O. ulmi) tolerance, but also an increase the genetic variability of tolerant...

  12. Effects of simulated acid rain, ozone and sulfur dioxide on suitability of elms for elm leaf beetle

    Treesearch

    Richard W. Hall; Jack H. Barger; Alden M. Townsend

    1988-01-01

    Cuttings from two clonally propagated elm hybrids ('Pioneer' and 'Homestead') were treated with ozone (03), sulfur dioxide (S02), simulated acid rain or left untreated. Fumigants were applied 7 hours per day, 5 days per week for 9 weeks in open-top chambers. Fumigation treatments were: 0.1 ppm 0

  13. Endonuclease EEPD1 Is a Gatekeeper for Repair of Stressed Replication Forks*

    PubMed Central

    Kim, Hyun-Suk; Nickoloff, Jac A.; Wu, Yuehan; Williamson, Elizabeth A.; Sidhu, Gurjit Singh; Reinert, Brian L.; Jaiswal, Aruna S.; Srinivasan, Gayathri; Patel, Bhavita; Kong, Kimi; Burma, Sandeep; Lee, Suk-Hee; Hromas, Robert A.

    2017-01-01

    Replication is not as continuous as once thought, with DNA damage frequently stalling replication forks. Aberrant repair of stressed replication forks can result in cell death or genome instability and resulting transformation to malignancy. Stressed replication forks are most commonly repaired via homologous recombination (HR), which begins with 5′ end resection, mediated by exonuclease complexes, one of which contains Exo1. However, Exo1 requires free 5′-DNA ends upon which to act, and these are not commonly present in non-reversed stalled replication forks. To generate a free 5′ end, stalled replication forks must therefore be cleaved. Although several candidate endonucleases have been implicated in cleavage of stalled replication forks to permit end resection, the identity of such an endonuclease remains elusive. Here we show that the 5′-endonuclease EEPD1 cleaves replication forks at the junction between the lagging parental strand and the unreplicated DNA parental double strands. This cleavage creates the structure that Exo1 requires for 5′ end resection and HR initiation. We observed that EEPD1 and Exo1 interact constitutively, and Exo1 repairs stalled replication forks poorly without EEPD1. Thus, EEPD1 performs a gatekeeper function for replication fork repair by mediating the fork cleavage that permits initiation of HR-mediated repair and restart of stressed forks. PMID:28049724

  14. 24. View of one of the plaques from Clark Fork ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    24. View of one of the plaques from Clark Fork Vehicle Bridge. Presently located at the Bonner County Historical Museum in Sandpoint, Idaho. A plaque was attached at each end of the bridge. Only one remains. - Clark Fork Vehicle Bridge, Spanning Clark Fork River, serves Highway 200, Clark Fork, Bonner County, ID

  15. 77 FR 76420 - Final Flood Elevation Determinations

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-28

    ... Fort Gay, confluence. Unincorporated Areas of Wayne County. At the Tug Fork +575 confluence. Mill Creek (backwater effects from From the Tug Fork +575 Town of Fort Gay. Tug Fork). confluence to approximately 1.1 miles upstream of the Tug Fork confluence. Tug Fork At the Big Sandy River +575 Town of Fort Gay...

  16. Pruning The ELM Survey: Characterizing Candidate Low-mass White Dwarfs through Photometric Variability

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bell, Keaton J.; Winget, D. E.; Montgomery, M. H.

    We assess the photometric variability of nine stars with spectroscopic T {sub eff} and log g values from the ELM Survey that locates them near the empirical extremely low-mass (ELM) white dwarf instability strip. We discover three new pulsating stars: SDSS J135512.34+195645.4, SDSS J173521.69+213440.6, and SDSS J213907.42+222708.9. However, these are among the few ELM Survey objects that do not show radial velocity (RV) variations that confirm the binary nature expected of helium-core white dwarfs. The dominant 4.31 hr pulsation in SDSS J135512.34+195645.4 far exceeds the theoretical cut-off for surface reflection in a white dwarf, and this target is likely amore » high-amplitude δ Scuti pulsator with an overestimated surface gravity. We estimate the probability to be less than 0.0008 that the lack of measured RV variations in four of eight other pulsating candidate ELM white dwarfs could be due to low orbital inclination. Two other targets exhibit variability as photometric binaries. Partial coverage of the 19.342 hr orbit of WD J030818.19+514011.5 reveals deep eclipses that imply a primary radius >0.4 R {sub ⊙}—too large to be consistent with an ELM white dwarf. The only object for which our time series photometry adds support to ELM white dwarf classification is SDSS J105435.78−212155.9, which has consistent signatures of Doppler beaming and ellipsoidal variations. We conclude that the ELM Survey contains multiple false positives from another stellar population at T {sub eff}≲9000 K, possibly related to the sdA stars recently reported from SDSS spectra.« less

  17. Connection between plasma response and resonant magnetic perturbation (RMP) edge localized mode (ELM) suppression in DIII-D [Connection between plasma response and RMP ELM suppression in DIII-D

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wingen, Andreas; Ferraro, Nathaniel M.; Shafer, Morgan W.

    Calculations of the plasma response to applied non-axisymmetric fields in several DIII-D discharges show that predicted displacements depend strongly on the edge current density. This result is found using both a linear two-fluid-MHD model (M3D-C1) and a nonlinear ideal-MHD model (VMEC). Furthermore, it is observed that the probability of a discharge being edge localized mode (ELM)-suppressed is most closely related to the edge current density, as opposed to the pressure gradient. It is found that discharges with a stronger kink response are closer to the peeling–ballooning stability limit in ELITE simulations and eventually cross into the unstable region, causing ELMsmore » to reappear. Thus for effective ELM suppression, the RMP has to prevent the plasma from generating a large kink response, associated with ELM instability. Experimental observations are in agreement with the finding; discharges which have a strong kink response in the MHD simulations show ELMs or ELM mitigation during the RMP phase of the experiment, while discharges with a small kink response in the MHD simulations are fully ELM suppressed in the experiment by the applied resonant magnetic perturbation. The results are cross-checked against modeled 3D ideal MHD equilibria using the VMEC code. The procedure of constructing optimal 3D equilibria for diverted H-mode discharges using VMEC is presented. As a result, kink displacements in VMEC are found to scale with the edge current density, similar to M3D-C1, but the displacements are smaller. A direct correlation in the flux surface displacements to the bootstrap current is shown.« less

  18. Connection between plasma response and resonant magnetic perturbation (RMP) edge localized mode (ELM) suppression in DIII-D [Connection between plasma response and RMP ELM suppression in DIII-D

    DOE PAGES

    Wingen, Andreas; Ferraro, Nathaniel M.; Shafer, Morgan W.; ...

    2015-09-03

    Calculations of the plasma response to applied non-axisymmetric fields in several DIII-D discharges show that predicted displacements depend strongly on the edge current density. This result is found using both a linear two-fluid-MHD model (M3D-C1) and a nonlinear ideal-MHD model (VMEC). Furthermore, it is observed that the probability of a discharge being edge localized mode (ELM)-suppressed is most closely related to the edge current density, as opposed to the pressure gradient. It is found that discharges with a stronger kink response are closer to the peeling–ballooning stability limit in ELITE simulations and eventually cross into the unstable region, causing ELMsmore » to reappear. Thus for effective ELM suppression, the RMP has to prevent the plasma from generating a large kink response, associated with ELM instability. Experimental observations are in agreement with the finding; discharges which have a strong kink response in the MHD simulations show ELMs or ELM mitigation during the RMP phase of the experiment, while discharges with a small kink response in the MHD simulations are fully ELM suppressed in the experiment by the applied resonant magnetic perturbation. The results are cross-checked against modeled 3D ideal MHD equilibria using the VMEC code. The procedure of constructing optimal 3D equilibria for diverted H-mode discharges using VMEC is presented. As a result, kink displacements in VMEC are found to scale with the edge current density, similar to M3D-C1, but the displacements are smaller. A direct correlation in the flux surface displacements to the bootstrap current is shown.« less

  19. Pruning The ELM Survey: Characterizing Candidate Low-mass White Dwarfs through Photometric Variability

    NASA Astrophysics Data System (ADS)

    Bell, Keaton J.; Gianninas, A.; Hermes, J. J.; Winget, D. E.; Kilic, Mukremin; Montgomery, M. H.; Castanheira, B. G.; Vanderbosch, Z.; Winget, K. I.; Brown, Warren R.

    2017-02-01

    We assess the photometric variability of nine stars with spectroscopic Teff and log g values from the ELM Survey that locates them near the empirical extremely low-mass (ELM) white dwarf instability strip. We discover three new pulsating stars: SDSS J135512.34+195645.4, SDSS J173521.69+213440.6, and SDSS J213907.42+222708.9. However, these are among the few ELM Survey objects that do not show radial velocity (RV) variations that confirm the binary nature expected of helium-core white dwarfs. The dominant 4.31 hr pulsation in SDSS J135512.34+195645.4 far exceeds the theoretical cut-off for surface reflection in a white dwarf, and this target is likely a high-amplitude δ Scuti pulsator with an overestimated surface gravity. We estimate the probability to be less than 0.0008 that the lack of measured RV variations in four of eight other pulsating candidate ELM white dwarfs could be due to low orbital inclination. Two other targets exhibit variability as photometric binaries. Partial coverage of the 19.342 hr orbit of WD J030818.19+514011.5 reveals deep eclipses that imply a primary radius >0.4 R⊙—too large to be consistent with an ELM white dwarf. The only object for which our time series photometry adds support to ELM white dwarf classification is SDSS J105435.78-212155.9, which has consistent signatures of Doppler beaming and ellipsoidal variations. We conclude that the ELM Survey contains multiple false positives from another stellar population at Teff ≲ 9000 K, possibly related to the sdA stars recently reported from SDSS spectra.

  20. ELM induced divertor heat loads on TCV

    NASA Astrophysics Data System (ADS)

    Marki, J.; Pitts, R. A.; Horacek, J.; Tskhakaya, D.; TCV Team

    2009-06-01

    Results are presented for heat loads at the TCV outer divertor target during ELMing H-mode using a fast IR camera. Benefitting from a recent surface cleaning of the entire first wall graphite armour, a comparison of the transient thermal response of freshly cleaned and untreated tile surfaces (coated with thick co-deposited layers) has been performed. The latter routinely exhibit temperature transients exceeding those of the clean ones by a factor ˜3, even if co-deposition throughout the first days of operation following the cleaning process leads to the steady regrowth of thin layers. Filaments are occasionally observed during the ELM heat flux rise phase, showing a spatial structure consistent with energy release at discrete toroidal locations in the outer midplane vicinity and with individual filaments carrying ˜1% of the total ELM energy. The temporal waveform of the ELM heat load is found to be in good agreement with the collisionless free streaming particle model.

  1. VizieR Online Data Catalog: Binary white dwarfs atmospheric parameters (Gianninas+, 2014)

    NASA Astrophysics Data System (ADS)

    Gianninas, A.; Dufour, P.; Kilic, M.; Brown, W. R.; Bergeron, P.; Hermes, J. J.

    2017-04-01

    The sample that we analyze includes a total of 61 ELM WD binaries from the ELM Survey (Brown et al. 2013, J/ApJ/769/66). The bulk of this sample is comprised of the 58 ELM WDs listed in Table 3 of Brown et al. (2013, J/ApJ/769/66), but also includes three additional ELM WDs that have been published in separate papers since then. The spectra of these 61 ELM WDs were obtained using five distinct setups on two different telescopes. A total of 57 targets were observed with the 6.5m MMT telescope with the Blue Channel spectrograph (Schmidt et al. 1989PASP..101..713S). The four remaining targets were observed using the Fred Lawrence Whipple Observatory's (FLWO) 1.5m Tilinghast telescope equipped with the FAST spectrograph (Fabricant et al. 1998PASP..110...79F) and the 600 line/mm grating. (2 data files).

  2. Not all triads are created equal: further support for the importance of visual and semantic proximity in object identification.

    PubMed

    Schweizer, Tom A; Dixon, Mike J; Desmarais, Geneviève; Smith, Stephen D

    2002-01-01

    Identification deficits were investigated in ELM, a temporal lobe stroke patient with category-specific deficits. We replicated previous work done on FS, a patient with category specific deficits as a result of herpes viral encephalitis. ELM was tested using novel, computer generated shapes that were paired with artifact labels. We paired semantically close or disparate labels to shapes and ELM attempted to learn these pairings. Overall, ELM's shape-label confusions were most detrimentally affected when we used labels that referred to objects that were visually and semantically close. However, as with FS, ELM had as many errors when shapes were paired with the labels "donut," "tire," and "washer" as he did when they were paired with visually and semantically close artifact labels. Two explanations are put forth to account for the anomalous performance by both patients on the triad of donut-tire-washer.

  3. Dynamics of energetic particle driven modes and MHD modes in wall-stabilized high-β plasmas on JT-60U and DIII-D

    NASA Astrophysics Data System (ADS)

    Matsunaga, G.; Okabayashi, M.; Aiba, N.; Boedo, J. A.; Ferron, J. R.; Hanson, J. M.; Hao, G. Z.; Heidbrink, W. W.; Holcomb, C. T.; In, Y.; Jackson, G. L.; Liu, Y. Q.; Luce, T. C.; McKee, G. R.; Osborne, T. H.; Pace, D. C.; Shinohara, K.; Snyder, P. B.; Solomon, W. M.; Strait, E. J.; Turnbull, A. D.; Van Zeeland, M. A.; Watkins, J. G.; Zeng, L.; the DIII-D Team; the JT-60 Team

    2013-12-01

    In the wall-stabilized high-β plasmas in JT-60U and DIII-D, interactions between energetic particle (EP) driven modes (EPdMs) and edge localized modes (ELMs) have been observed. The interaction between the EPdM and ELM are reproducibly observed. Many EP diagnostics indicate a strong correlation between the distorted waveform of the EPdM and the EP transport to the edge. The waveform distortion is composed of higher harmonics (n ⩾ 2) and looks like a density snake near the plasma edge. According to statistical analyses, ELM triggering by the EPdMs requires a finite level of waveform distortion and pedestal recovery. ELM pacing by the EPdMs occurs when the repetition frequency of the EPdMs is higher than the natural ELM frequency. EPs transported by EPdMs are thought to contribute to change the edge stability.

  4. Multilayer Extreme Learning Machine With Subnetwork Nodes for Representation Learning.

    PubMed

    Yang, Yimin; Wu, Q M Jonathan

    2016-11-01

    The extreme learning machine (ELM), which was originally proposed for "generalized" single-hidden layer feedforward neural networks, provides efficient unified learning solutions for the applications of clustering, regression, and classification. It presents competitive accuracy with superb efficiency in many applications. However, ELM with subnetwork nodes architecture has not attracted much research attentions. Recently, many methods have been proposed for supervised/unsupervised dimension reduction or representation learning, but these methods normally only work for one type of problem. This paper studies the general architecture of multilayer ELM (ML-ELM) with subnetwork nodes, showing that: 1) the proposed method provides a representation learning platform with unsupervised/supervised and compressed/sparse representation learning and 2) experimental results on ten image datasets and 16 classification datasets show that, compared to other conventional feature learning methods, the proposed ML-ELM with subnetwork nodes performs competitively or much better than other feature learning methods.

  5. "A Victim of Its Own Success"? The Diploma in Addiction Studies at Trinity College Dublin

    ERIC Educational Resources Information Center

    Woods, Marguerite; Butler, Shane

    2011-01-01

    This article reviews and reflects on the Diploma in Addiction Studies: a 1-year, full-time programme taught at the School of Social Work and Social Policy in Trinity College Dublin since the academic year 1983/1984, which has recently had its external funding withdrawn. The programme was aimed at multidisciplinary classes, including students from…

  6. "The Problem of Trinity College Dublin": A Historical Perspective on Rationalisation in Higher Education in Ireland

    ERIC Educational Resources Information Center

    Walsh, John

    2014-01-01

    This paper offers a historical perspective on government policies for the rationalisation of higher education (HE) in Ireland through a critical re-appraisal of the initiative for "merger" of Trinity College and University College Dublin. The initiative launched by Donogh O'Malley in 1967 was the first significant attempt by an Irish…

  7. Seeing the Light: Visibility of the July '45 Trinity Atomic Bomb Test from the Inner Solar System

    ERIC Educational Resources Information Center

    Reed, B. Cameron

    2006-01-01

    In his "The Making of the Atomic Bomb," Richard Rhodes remarks of the July 16, 1945, Trinity atomic bomb test in New Mexico that "had astronomers been watching they could have seen it reflected from the moon, literal moonshine," an allusion to Ernest Rutherford's famous dismissal of the prospect of atomic energy. Investigating…

  8. LLNL Mercury Project Trinity Open Science Final Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Dawson, Shawn A.

    The Mercury Monte Carlo particle transport code is used to simulate the transport of radiation through urban environments. These challenging calculations include complicated geometries and require significant computational resources to complete. In the proposed Trinity Open Science calculations, I will investigate computer science aspects of the code which are relevant to convergence of the simulation quantities with increasing Monte Carlo particle counts.

  9. Factors regulating early life history dispersal of Atlantic cod (Gadus morhua) from coastal Newfoundland.

    PubMed

    Stanley, Ryan R E; deYoung, Brad; Snelgrove, Paul V R; Gregory, Robert S

    2013-01-01

    To understand coastal dispersal dynamics of Atlantic cod (Gadus morhua), we examined spatiotemporal egg and larval abundance patterns in coastal Newfoundland. In recent decades, Smith Sound, Trinity Bay has supported the largest known overwintering spawning aggregation of Atlantic cod in the region. We estimated spawning and dispersal characteristics for the Smith Sound-Trinity Bay system by fitting ichthyoplankton abundance data to environmentally-driven, simplified box models. Results show protracted spawning, with sharply increased egg production in early July, and limited dispersal from the Sound. The model for the entire spawning season indicates egg export from Smith Sound is 13%•day(-1) with a net mortality of 27%•day(-1). Eggs and larvae are consistently found in western Trinity Bay with little advection from the system. These patterns mirror particle tracking models that suggest residence times of 10-20 days, and circulation models indicating local gyres in Trinity Bay that act in concert with upwelling dynamics to retain eggs and larvae. Our results are among the first quantitative dispersal estimates from Smith Sound, linking this spawning stock to the adjacent coastal waters. These results illustrate the biophysical interplay regulating dispersal and connectivity originating from inshore spawning of coastal northwest Atlantic.

  10. Geohydrologic Framework of the Edwards and Trinity Aquifers, South-Central Texas

    USGS Publications Warehouse

    Blome, Charles D.; Faith, Jason R.; Ozuna, George B.

    2007-01-01

    This five-year USGS project, funded by the National Cooperative Geologic Mapping Program, is using multidisciplinary approaches to reveal the surface and subsurface geologic architecture of two important Texas aquifers: (1) the Edwards aquifer that extends from south of Austin to west of San Antonio and (2) the southern part of the Trinity aquifer in the Texas Hill Country west and south of Austin. The project's principal areas of research include: Geologic Mapping, Geophysical Surveys, Geochronology, Three-dimensional Modeling, and Noble Gas Geochemistry. The Edwards aquifer is one of the most productive carbonate aquifers in the United States. It also has been designated a sole source aquifer by the U.S. Environmental Protection Agency and is the primary source of water for San Antonio, America's eighth largest city. The Trinity aquifer forms the catchment area for the Edwards aquifer and it intercepts some surface flow above the Edwards recharge zone. The Trinity may also contribute to the Edwards water budget by subsurface flow across formation boundaries at considerable depths. Dissolution, karst development, and faulting and fracturing in both aquifers directly control aquifer geometry by compartmentalizing the aquifer and creating unique ground-water flow paths.

  11. Recent Performance Results of VPIC on Trinity

    NASA Astrophysics Data System (ADS)

    Nystrom, W. D.; Bergen, B.; Bird, R. F.; Bowers, K. J.; Daughton, W. S.; Guo, F.; Le, A.; Li, H.; Nam, H.; Pang, X.; Stark, D. J.; Rust, W. N., III; Yin, L.; Albright, B. J.

    2017-10-01

    Trinity is a new DOE compute resource now in production at Los Alamos National Laboratory. Trinity has several new and unique features including two compute partitions, one with dual socket Intel Haswell Xeon compute nodes and one with Intel Knights Landing (KNL) Xeon Phi compute nodes, use of on package high bandwidth memory (HBM) for KNL nodes, ability to configure KNL nodes with respect to HBM model and on die network topology in a variety of operational modes at run time, and use of solid state storage via burst buffer technology to reduce time required to perform I/O. An effort is in progress to optimize VPIC on Trinity by taking advantage of these new architectural features. Results of work will be presented on performance of VPIC on Haswell and KNL partitions for single node runs and runs at scale. Results include use of burst buffers at scale to optimize I/O, comparison of strategies for using MPI and threads, performance benefits using HBM and effectiveness of using intrinsics for vectorization. Work performed under auspices of U.S. Dept. of Energy by Los Alamos National Security, LLC Los Alamos National Laboratory under contract DE-AC52-06NA25396 and supported by LANL LDRD program.

  12. Geologic and hydrostratigraphic map of the Anhalt, Fischer, and Spring Branch 7.5-minute quadrangles, Blanco, Comal, and Kendall Counties, Texas

    USGS Publications Warehouse

    Clark, Allan K.; Robert R. Morris,

    2015-01-01

    The hydrostratigraphic units of the Edwards and Trinity aquifers have been mapped and described herein using a classification system developed by Choquette and Pray (1970), which is based on porosity types being fabric or not-fabric selective. The naming of hydrostratigraphic units is also based on preexisting names and topographic or historical features that occur in outcrop. The only hydrostratigraphic unit of the Edwards aquifer present in the study area is VIII hydrostratigraphic unit. The mapped hydrostratigraphic units of the upper Trinity aquifer are, from top to bottom: the cavernous, Camp Bullis, upper evaporite, fossiliferous, and lower evaporite and they are interval equivalent to the upper member of the Glen Rose Limestone. The middle Trinity aquifer (interval equivalent to the lower member of the Glen Rose Limestone) contains, from top to bottom: the Bulverde, Little Blanco, Twin Sisters, Doeppenschmidt, Rust, and Honey Creek hydrostratigraphic units. The lower part of the middle Trinity aquifer is formed by the Hensell, Cow Creek, and Hammett hydrostratigraphic units which are interval equivalent to the Hensell Sand Member, the Cow Creek Limestone, and the Hammett Shale Member, respectively, of the Pearsall Formation.

  13. Both DNA Polymerases δ and ε Contact Active and Stalled Replication Forks Differently

    PubMed Central

    Yu, Chuanhe; Gan, Haiyun

    2017-01-01

    ABSTRACT Three DNA polymerases, polymerases α, δ, and ε (Pol α, Pol δ, and Pol ε), are responsible for eukaryotic genome duplication. When DNA replication stress is encountered, DNA synthesis stalls until the stress is ameliorated. However, it is not known whether there is a difference in the association of each polymerase with active and stalled replication forks. Here, we show that each DNA polymerase has a distinct pattern of association with active and stalled replication forks. Pol α is enriched at extending Okazaki fragments of active and stalled forks. In contrast, although Pol δ contacts the nascent lagging strands of active and stalled forks, it binds to only the matured (and not elongating) Okazaki fragments of stalled forks. Pol ε has greater contact with the nascent single-stranded DNA (ssDNA) of the leading strand on active forks than on stalled forks. We propose that the configuration of DNA polymerases at stalled forks facilitates the resumption of DNA synthesis after stress removal. PMID:28784720

  14. Establishment patterns of water-elm at Catahoula Lake, Louisiana

    Treesearch

    Karen S. Doerr; Sanjeev Joshi; Richard F. Keim

    2015-01-01

    At Catahoula Lake in central Louisiana, an internationally important lake for water fowl, hydrologic alterations to the surrounding rivers and the lake itself have led to an expansion of water-elm (Planera aquatic J.F. Gmel.) into the lake bed. In this study, we used dendrochronology and aerial photography to quantify the expansion of water-elm in the lake and identify...

  15. Pruning cycles and storm damage: are young American elms failing prematurely?

    Treesearch

    Chad P. Giblin

    2017-01-01

    The use of Dutch elm disease-resistant elms as a common replacement tree in municipal planting schedules has amassed a large population of these trees in many cities throughout the eastern half of the United States. Reports from practitioners have suggested that this population is vulnerable to catastrophic losses due to severe canopy failures during wind-loading...

  16. Challenge inoculations to test for Dutch elm disease tolerance: a summary of methods used by various researchers

    Treesearch

    Linda M. Haugen; Garrett L. Beier; Susan E. Bentz; Raymond P. Guries; James M. Slavicek

    2017-01-01

    A variety of methods have been used by different research groups to "challenge" inoculate American elms (Ulmus americana) with the purpose of determining whether some clones may be resistant to the Dutch elm disease fungus. The methods used by seven research groups are described, along with observations on complications and benefits...

  17. Host acceptance and larval competition between the invasive banded and European elm bark beetles (Coleoptera: Scolytidae): Potential mechanisms for competitive displacement

    Treesearch

    J.C. Lee; S.J. Seybold

    2009-01-01

    A recent survey revealed that the newly invasive banded elm bark beetle, Scolytus schevyrewi, was much more abundant than the long-established European elm bark beetle, S. multistriatus, in areas of Colorado and Wyoming, USA. This study was initiated to determine whether competitive displacement of S. multistriatus...

  18. Height preference of Scolytus schevyrewi Semenov, the banded elm bark beetle of American elm, Ulmus americana

    Treesearch

    S. McElwey; J. F. Negron; J. Withrow

    2007-01-01

    Scolytus schevyrewi Semenov, the banded elm bark beetle, was first detected in North America in April 2003 in Colorado and Utah by the Rapid Detection and Response Pilot Project sponsored by APHIS and USDA Forest Service, Forest Health Protection. It was captured in Lindgren funnel traps baited with a-pinene, ethanol, and the Ips typographus...

  19. Observations of ELM stabilization during neutral beam injection in DIII-D

    NASA Astrophysics Data System (ADS)

    Bortolon, Alessandro; Kramer, Gerrit; Diallo, Ahmed; Knolker, Matthias; Maingi, Rajesh; Nazikian, Raffi; Degrassie, John; Osborne, Thomas

    2017-10-01

    Edge localized modes (ELMs) are generally interpreted as peeling-ballooning instabilities, driven by the pedestal current and pressure gradient, with other subdominant effects possibly relevant close to marginal stability. We report observations of transient stabilization of type-I ELMs during neutral beam injection (NBI), emerging from a combined dataset of DIII-D ELMy H-mode plasmas with moderate heating obtained through pulsed NBI waveforms. Statistical analysis of ELM onset times indicates that, in the selected dataset, the likelihood of onset of an ELM lowers significantly during NBI modulation pulses, with the stronger correlation found with counter-current NBI. The effect is also found in rf-heated H-modes, where ELMs appear inhibited when isolated diagnostic beam pulses are applied. Coherent average analysis is used to determine how plasma density, temperature, rotation as well as beam ion quantities evolve during a NB modulation cycle, finding relatively small changes ( 3%) of pedestal Te and ne and toroidal and poloidal rotation variations up to 5 km/s. The effect of these changes on pedestal stability will be discussed. Work supported by US DOE under DE-FC02-04ER54698, DE-AC02-09CH11466.

  20. Resistance to Dutch Elm Disease Reduces Presence of Xylem Endophytic Fungi in Elms (Ulmus spp.)

    PubMed Central

    Martín, Juan A.; Witzell, Johanna; Blumenstein, Kathrin; Rozpedowska, Elzbieta; Helander, Marjo; Sieber, Thomas N.; Gil, Luis

    2013-01-01

    Efforts to introduce pathogen resistance into landscape tree species by breeding may have unintended consequences for fungal diversity. To address this issue, we compared the frequency and diversity of endophytic fungi and defensive phenolic metabolites in elm (Ulmus spp.) trees with genotypes known to differ in resistance to Dutch elm disease. Our results indicate that resistant U. minor and U. pumila genotypes exhibit a lower frequency and diversity of fungal endophytes in the xylem than susceptible U. minor genotypes. However, resistant and susceptible genotypes showed a similar frequency and diversity of endophytes in the leaves and bark. The resistant and susceptible genotypes could be discriminated on the basis of the phenolic profile of the xylem, but not on basis of phenolics in the leaves or bark. As the Dutch elm disease pathogen develops within xylem tissues, the defensive chemistry of resistant elm genotypes thus appears to be one of the factors that may limit colonization by both the pathogen and endophytes. We discuss a potential trade-off between the benefits of breeding resistance into tree species, versus concomitant losses of fungal endophytes and the ecosystem services they provide. PMID:23468900

  1. ELM: the status of the 2010 eukaryotic linear motif resource

    PubMed Central

    Gould, Cathryn M.; Diella, Francesca; Via, Allegra; Puntervoll, Pål; Gemünd, Christine; Chabanis-Davidson, Sophie; Michael, Sushama; Sayadi, Ahmed; Bryne, Jan Christian; Chica, Claudia; Seiler, Markus; Davey, Norman E.; Haslam, Niall; Weatheritt, Robert J.; Budd, Aidan; Hughes, Tim; Paś, Jakub; Rychlewski, Leszek; Travé, Gilles; Aasland, Rein; Helmer-Citterich, Manuela; Linding, Rune; Gibson, Toby J.

    2010-01-01

    Linear motifs are short segments of multidomain proteins that provide regulatory functions independently of protein tertiary structure. Much of intracellular signalling passes through protein modifications at linear motifs. Many thousands of linear motif instances, most notably phosphorylation sites, have now been reported. Although clearly very abundant, linear motifs are difficult to predict de novo in protein sequences due to the difficulty of obtaining robust statistical assessments. The ELM resource at http://elm.eu.org/ provides an expanding knowledge base, currently covering 146 known motifs, with annotation that includes >1300 experimentally reported instances. ELM is also an exploratory tool for suggesting new candidates of known linear motifs in proteins of interest. Information about protein domains, protein structure and native disorder, cellular and taxonomic contexts is used to reduce or deprecate false positive matches. Results are graphically displayed in a ‘Bar Code’ format, which also displays known instances from homologous proteins through a novel ‘Instance Mapper’ protocol based on PHI-BLAST. ELM server output provides links to the ELM annotation as well as to a number of remote resources. Using the links, researchers can explore the motifs, proteins, complex structures and associated literature to evaluate whether candidate motifs might be worth experimental investigation. PMID:19920119

  2. Inhibition of phenylpropanoid biosynthesis increases cell wall digestibility, protoplast isolation, and facilitates sustained cell division in American elm (Ulmus americana).

    PubMed

    Jones, A Maxwell P; Chattopadhyay, Abhishek; Shukla, Mukund; Zoń, Jerzy; Saxena, Praveen K

    2012-05-30

    Protoplast technologies offer unique opportunities for fundamental research and to develop novel germplasm through somatic hybridization, organelle transfer, protoclonal variation, and direct insertion of DNA. Applying protoplast technologies to develop Dutch elm disease resistant American elms (Ulmus americana L.) was proposed over 30 years ago, but has not been achieved. A primary factor restricting protoplast technology to American elm is the resistance of the cell walls to enzymatic degradation and a long lag phase prior to cell wall re-synthesis and cell division. This study suggests that resistance to enzymatic degradation in American elm was due to water soluble phenylpropanoids. Incubating tobacco (Nicotiana tabacum L.) leaf tissue, an easily digestible species, in aqueous elm extract inhibits cell wall digestion in a dose dependent manner. This can be mimicked by p-coumaric or ferulic acid, phenylpropanoids known to re-enforce cell walls. Culturing American elm tissue in the presence of 2-aminoindane-2-phosphonic acid (AIP; 10-150 μM), an inhibitor of phenylalanine ammonia lyase (PAL), reduced flavonoid content, decreased tissue browning, and increased isolation rates significantly from 11.8% (±3.27) in controls to 65.3% (±4.60). Protoplasts isolated from callus grown in 100 μM AIP developed cell walls by day 2, had a division rate of 28.5% (±3.59) by day 6, and proliferated into callus by day 14. Heterokaryons were successfully produced using electrofusion and fused protoplasts remained viable when embedded in agarose. This study describes a novel approach of modifying phenylpropanoid biosynthesis to facilitate efficient protoplast isolation which has historically been problematic for American elm. This isolation system has facilitated recovery of viable protoplasts capable of rapid cell wall re-synthesis and sustained cell division to form callus. Further, isolated protoplasts survived electrofusion and viable heterokaryons were produced. Together, these results provide the first evidence of sustained cell division, callus regeneration, and potential application of somatic cell fusion in American elm, suggesting that this source of protoplasts may be ideal for genetic manipulation of this species. The technological advance made with American elm in this study has potential implications in other woody species for fundamental and applied research which require availability of viable protoplasts.

  3. Inhibition of phenylpropanoid biosynthesis increases cell wall digestibility, protoplast isolation, and facilitates sustained cell division in American elm (Ulmus americana)

    PubMed Central

    2012-01-01

    Background Protoplast technologies offer unique opportunities for fundamental research and to develop novel germplasm through somatic hybridization, organelle transfer, protoclonal variation, and direct insertion of DNA. Applying protoplast technologies to develop Dutch elm disease resistant American elms (Ulmus americana L.) was proposed over 30 years ago, but has not been achieved. A primary factor restricting protoplast technology to American elm is the resistance of the cell walls to enzymatic degradation and a long lag phase prior to cell wall re-synthesis and cell division. Results This study suggests that resistance to enzymatic degradation in American elm was due to water soluble phenylpropanoids. Incubating tobacco (Nicotiana tabacum L.) leaf tissue, an easily digestible species, in aqueous elm extract inhibits cell wall digestion in a dose dependent manner. This can be mimicked by p-coumaric or ferulic acid, phenylpropanoids known to re-enforce cell walls. Culturing American elm tissue in the presence of 2-aminoindane-2-phosphonic acid (AIP; 10-150 μM), an inhibitor of phenylalanine ammonia lyase (PAL), reduced flavonoid content, decreased tissue browning, and increased isolation rates significantly from 11.8% (±3.27) in controls to 65.3% (±4.60). Protoplasts isolated from callus grown in 100 μM AIP developed cell walls by day 2, had a division rate of 28.5% (±3.59) by day 6, and proliferated into callus by day 14. Heterokaryons were successfully produced using electrofusion and fused protoplasts remained viable when embedded in agarose. Conclusions This study describes a novel approach of modifying phenylpropanoid biosynthesis to facilitate efficient protoplast isolation which has historically been problematic for American elm. This isolation system has facilitated recovery of viable protoplasts capable of rapid cell wall re-synthesis and sustained cell division to form callus. Further, isolated protoplasts survived electrofusion and viable heterokaryons were produced. Together, these results provide the first evidence of sustained cell division, callus regeneration, and potential application of somatic cell fusion in American elm, suggesting that this source of protoplasts may be ideal for genetic manipulation of this species. The technological advance made with American elm in this study has potential implications in other woody species for fundamental and applied research which require availability of viable protoplasts. PMID:22646730

  4. Divertor power and particle fluxes between and during type-I ELMs in the ASDEX Upgrade

    NASA Astrophysics Data System (ADS)

    Kallenbach, A.; Dux, R.; Eich, T.; Fischer, R.; Giannone, L.; Harhausen, J.; Herrmann, A.; Müller, H. W.; Pautasso, G.; Wischmeier, M.; ASDEX Upgrade Team

    2008-08-01

    Particle, electric charge and power fluxes for type-I ELMy H-modes are measured in the divertor of the ASDEX Upgrade tokamak by triple Langmuir probes, shunts, infrared (IR) thermography and spectroscopy. The discharges are in the medium to high density range, resulting in predominantly convective edge localized modes (ELMs) with moderate fractional stored energy losses of 2% or below. Time resolved data over ELM cycles are obtained by coherent averaging of typically one hundred similar ELMs, spatial profiles from the flush-mounted Langmuir probes are obtained by strike point sweeps. The application of simple physics models is used to compare different diagnostics and to make consistency checks, e.g. the standard sheath model applied to the Langmuir probes yields power fluxes which are compared with the thermographic measurements. In between ELMs, Langmuir probe and thermography power loads appear consistent in the outer divertor, taking into account additional load due to radiation and charge exchange neutrals measured by thermography. The inner divertor is completely detached and no significant power flow by charged particles is measured. During ELMs, quite similar power flux profiles are found in the outer divertor by thermography and probes, albeit larger uncertainties in Langmuir probe evaluation during ELMs have to be taken into account. In the inner divertor, ELM power fluxes from thermography are a factor 10 larger than those derived from probes using the standard sheath model. This deviation is too large to be caused by deficiencies of probe analysis. The total ELM energy deposition from IR is about a factor 2 higher in the inner divertor compared with the outer divertor. Spectroscopic measurements suggest a quite moderate contribution of radiation to the target power load. Shunt measurements reveal a significant positive charge flow into the inner target during ELMs. The net number of elementary charges correlates well with the total core particle loss obtained from highly resolved density profiles. As a consequence, the discrepancy between probe and IR measurements is attributed to the ion power channel via a high mean impact energy of the ions at the inner target. The dominant contributing mechanism is proposed to be the directed loss of ions from the pedestal region into the inner divertor.

  5. Rinne revisited: steel versus aluminum tuning forks.

    PubMed

    MacKechnie, Cheryl A; Greenberg, Jesse J; Gerkin, Richard C; McCall, Andrew A; Hirsch, Barry E; Durrant, John D; Raz, Yael

    2013-12-01

    (1) Determine whether tuning fork material (aluminum vs stainless steel) affects Rinne testing in the clinical assessment of conductive hearing loss (CHL). (2) Determine the relative acoustic and mechanical outputs of 512-Hz tuning forks made of aluminum and stainless steel. Prospective, observational. Outpatient otology clinic. Fifty subjects presenting May 2011 to May 2012 with negative or equivocal Rinne in at least 1 ear and same-day audiometry. Rinne test results using aluminum and steel forks were compared and correlated with the audiometric air-bone gap. Bench top measurements using sound-level meter, microphone, and artificial mastoid. Patients with CHL were more likely to produce a negative Rinne test with a steel fork than with an aluminum fork. Logistic regression revealed that the probability of a negative Rinne reached 50% at a 19 dB air-bone gap for stainless steel versus 27 dB with aluminum. Bench top testing revealed that steel forks demonstrate, in effect, more comparable air and bone conduction efficiencies while aluminum forks have relatively lower bone conduction efficiency. We have found that steel tuning forks can detect a lesser air-bone gap compared to aluminum tuning forks. This is substantiated by observations of clear differences in the relative acoustic versus mechanical outputs of steel and aluminum forks, reflecting underlying inevitable differences in acoustic versus mechanical impedances of these devices, and thus efficiency of coupling sound/vibratory energy to the auditory system. These findings have clinical implications for using tuning forks to determine candidacy for stapes surgery.

  6. De novo transcript sequence reconstruction from RNA-Seq: reference generation and analysis with Trinity

    PubMed Central

    Yassour, Moran; Grabherr, Manfred; Blood, Philip D.; Bowden, Joshua; Couger, Matthew Brian; Eccles, David; Li, Bo; Lieber, Matthias; MacManes, Matthew D.; Ott, Michael; Orvis, Joshua; Pochet, Nathalie; Strozzi, Francesco; Weeks, Nathan; Westerman, Rick; William, Thomas; Dewey, Colin N.; Henschel, Robert; LeDuc, Richard D.; Friedman, Nir; Regev, Aviv

    2013-01-01

    De novo assembly of RNA-Seq data allows us to study transcriptomes without the need for a genome sequence, such as in non-model organisms of ecological and evolutionary importance, cancer samples, or the microbiome. In this protocol, we describe the use of the Trinity platform for de novo transcriptome assembly from RNA-Seq data in non-model organisms. We also present Trinity’s supported companion utilities for downstream applications, including RSEM for transcript abundance estimation, R/Bioconductor packages for identifying differentially expressed transcripts across samples, and approaches to identify protein coding genes. In an included tutorial we provide a workflow for genome-independent transcriptome analysis leveraging the Trinity platform. The software, documentation and demonstrations are freely available from http://trinityrnaseq.sf.net. PMID:23845962

  7. A conceptual model of the hydrogeologic framework, geochemistry, and groundwater-flow system of the Edwards-Trinity and related aquifers in the Pecos County region, Texas

    USGS Publications Warehouse

    Bumgarner, Johnathan R.; Stanton, Gregory P.; Teeple, Andrew; Thomas, Jonathan V.; Houston, Natalie A.; Payne, Jason; Musgrove, MaryLynn

    2012-01-01

    A conceptual model of the hydrogeologic framework, geochemistry, and groundwater-flow system of the Edwards-Trinity and related aquifers, which include the Pecos Valley, Igneous, Dockum, Rustler, and Capitan Reef aquifers, was developed as the second phase of a groundwater availability study in the Pecos County region in west Texas. The first phase of the study was to collect and compile groundwater, surface-water, water-quality, geophysical, and geologic data in the area. The third phase of the study involves a numerical groundwater-flow model of the Edwards-Trinity aquifer in order to simulate groundwater conditions based on various groundwater-withdrawal scenarios. Resource managers plan to use the results of the study to establish management strategies for the groundwater system. The hydrogeologic framework is composed of the hydrostratigraphy, structural features, and hydraulic properties of the groundwater system. Well and geophysical logs were interpreted to define the top and base surfaces of the Edwards-Trinity aquifer units. Elevations of the top and base of the Edwards-Trinity aquifer generally decrease from the southwestern part of the study area to the northeast. The thicknesses of the Edwards-Trinity aquifer units were calculated using the interpolated top and base surfaces of the hydrostratigraphic units. Some of the thinnest sections of the aquifer were in the eastern part of the study area and some of the thickest sections were in the Pecos, Monument Draw, and Belding-Coyanosa trough areas. Normal-fault zones, which formed as growth and collapse features as sediments were deposited along the margins of more resistant rocks and as overlying sediments collapsed into the voids created by the dissolution of Permian-age evaporite deposits, were delineated based on the interpretation of hydrostratigraphic cross sections. The lowest aquifer transmissivity values were measured in the eastern part of the study area; the highest transmissivity values were measured in a faulted area of the Monument Draw trough. Hydraulic conductivity values generally exhibited the same trends as the transmissivity values. Groundwater-quality data and groundwater-level data were used in context with the hydrogeologic framework to assess the chemical characteristics of water from different sources, regional groundwater-flow paths, recharge sources, the mixing of water from different sources, and discharge in the study area. Groundwater-level altitudes generally decrease from southwest to northeast and regional groundwater flow is from areas of recharge south and west to the north and northeast. Four principal sources of recharge to the Edwards-Trinity aquifer were identified: (1) regional flow that originated as recharge northwest of the study area, (2) runoff from the Barilla, Davis, and Glass Mountains, (3) return flow from irrigation, and (4) upwelling from deeper aquifers. Results indicated Edwards-Trinity aquifer water in the study area was dominated by mineralized, regional groundwater flow that most likely recharged during the cooler, wetter climates of the Pleistocene with variable contributions of recent, local recharge. Groundwater generally flows into the down-dip extent of the Edwards-Trinity aquifer where it discharges into overlying or underlying aquifer units, discharges from springs, discharges to the Pecos River, follows a regional flow path east out of the study area, or is withdrawn by groundwater wells. Structural features such as mountains, troughs, and faults play a substantial role in the distribution of recharge, local and regional groundwater flow, spring discharge, and aquifer interaction.

  8. An Incremental Type-2 Meta-Cognitive Extreme Learning Machine.

    PubMed

    Pratama, Mahardhika; Zhang, Guangquan; Er, Meng Joo; Anavatti, Sreenatha

    2017-02-01

    Existing extreme learning algorithm have not taken into account four issues: 1) complexity; 2) uncertainty; 3) concept drift; and 4) high dimensionality. A novel incremental type-2 meta-cognitive extreme learning machine (ELM) called evolving type-2 ELM (eT2ELM) is proposed to cope with the four issues in this paper. The eT2ELM presents three main pillars of human meta-cognition: 1) what-to-learn; 2) how-to-learn; and 3) when-to-learn. The what-to-learn component selects important training samples for model updates by virtue of the online certainty-based active learning method, which renders eT2ELM as a semi-supervised classifier. The how-to-learn element develops a synergy between extreme learning theory and the evolving concept, whereby the hidden nodes can be generated and pruned automatically from data streams with no tuning of hidden nodes. The when-to-learn constituent makes use of the standard sample reserved strategy. A generalized interval type-2 fuzzy neural network is also put forward as a cognitive component, in which a hidden node is built upon the interval type-2 multivariate Gaussian function while exploiting a subset of Chebyshev series in the output node. The efficacy of the proposed eT2ELM is numerically validated in 12 data streams containing various concept drifts. The numerical results are confirmed by thorough statistical tests, where the eT2ELM demonstrates the most encouraging numerical results in delivering reliable prediction, while sustaining low complexity.

  9. Helicopter Electromagnetic and Magnetic Surveys of the Upper and Middle Zones of the Trinity Aquifer, Uvalde and Bexar Counties, Texas

    NASA Astrophysics Data System (ADS)

    Smith, D. V.; Blome, C. D.; Smith, B. D.; Clark, A. C.

    2009-12-01

    Detailed helicopter electromagnetic and magnetic surveys (HEM) were conducted in northern Uvalde and Bexar Counties, Texas, as part of a geologic mapping and hydrologic study being conducted by the U.S. Geological Survey (USGS). The aquifers of the Lower Cretaceous Trinity Group (collectively termed the Trinity aquifer) are an important regional water source in the Hill Country of south-central Texas. Rock units comprising the middle aquifer segment are represented by the lower member of the Glen Rose Formation and the Cow Creek Limestone and Hensel Sandstone members of the Pearsall Formation. The lower Trinity hydrologic segment is composed of the Hosston and Sligo Limestones and is confined by the overlying Hammet Shale. Karst features commonly occur in the Trinity Group because of the dissolution of gypsum- and anhydrite-rich beds. Faults and fractures have not been sufficiently analyzed to evaluate the effects these structures have on inter- and intra-formational groundwater flow. The survey in the north Seco Creek area covers the recharge zone of the Edwards aquifer and part of the catchment zone composed of the upper Trinity segment. These data augment the scant geologic mapping in the area by delineating faults, collapse features, and hydrostratigraphic units. The HEM survey in northern Bexar County covered the Camp Stanley Storage Activity, the Camp Bullis Training Site, parts of the recharge zone of the Edwards aquifer south of the military bases, and part of Cibolo Creek to the north. Basic line spacing was 200 meters using six frequencies. In-fill lines were flown with a spacing of 100 meters in the central part of the study area to better resolve geologic structures and karst features. The data processing took into account high EM interference and cultural noise. Apparent resistivity (ρa) maps are used in interpretation of geologic structures, trends, and in the identification of electrical properties of lithologic units. The ρa maps show the northwest trending faults of the Balcones fault zone as well as oblique trending cross faults. Though many of the major faults had been identified in previous geologic mapping, other possibly significant faults were not recognized from traditional techniques. High resistivities within the Glen Rose Limestone are indicative of more competent lithologies which have a greater limestone content. During the evolution of the groundwater system the limestone units are most likely to have developed secondary porosity conducive to establishing flow paths. In contrast, lower resistivities are associated with clay, marl, and mudstone units which have lower porosity and permeability. Resistivity depth sections along flight lines and 3D visualization of resistive zones define reefal structures in the middle Trinity segment. Detailed hydrogeologic mapping and HEM depth modeling illustrate the approach to be taken in future studies of the Trinity.

  10. ELM-induced transient tungsten melting in the JET divertor

    NASA Astrophysics Data System (ADS)

    Coenen, J. W.; Arnoux, G.; Bazylev, B.; Matthews, G. F.; Autricque, A.; Balboa, I.; Clever, M.; Dejarnac, R.; Coffey, I.; Corre, Y.; Devaux, S.; Frassinetti, L.; Gauthier, E.; Horacek, J.; Jachmich, S.; Komm, M.; Knaup, M.; Krieger, K.; Marsen, S.; Meigs, A.; Mertens, Ph.; Pitts, R. A.; Puetterich, T.; Rack, M.; Stamp, M.; Sergienko, G.; Tamain, P.; Thompson, V.; Contributors, JET-EFDA

    2015-02-01

    The original goals of the JET ITER-like wall included the study of the impact of an all W divertor on plasma operation (Coenen et al 2013 Nucl. Fusion 53 073043) and fuel retention (Brezinsek et al 2013 Nucl. Fusion 53 083023). ITER has recently decided to install a full-tungsten (W) divertor from the start of operations. One of the key inputs required in support of this decision was the study of the possibility of W melting and melt splashing during transients. Damage of this type can lead to modifications of surface topology which could lead to higher disruption frequency or compromise subsequent plasma operation. Although every effort will be made to avoid leading edges, ITER plasma stored energies are sufficient that transients can drive shallow melting on the top surfaces of components. JET is able to produce ELMs large enough to allow access to transient melting in a regime of relevance to ITER. Transient W melt experiments were performed in JET using a dedicated divertor module and a sequence of IP = 3.0 MA/BT = 2.9 T H-mode pulses with an input power of PIN = 23 MW, a stored energy of ˜6 MJ and regular type I ELMs at ΔWELM = 0.3 MJ and fELM ˜ 30 Hz. By moving the outer strike point onto a dedicated leading edge in the W divertor the base temperature was raised within ˜1 s to a level allowing transient, ELM-driven melting during the subsequent 0.5 s. Such ELMs (δW ˜ 300 kJ per ELM) are comparable to mitigated ELMs expected in ITER (Pitts et al 2011 J. Nucl. Mater. 415 (Suppl.) S957-64). Although significant material losses in terms of ejections into the plasma were not observed, there is indirect evidence that some small droplets (˜80 µm) were released. Almost 1 mm (˜6 mm3) of W was moved by ˜150 ELMs within 7 subsequent discharges. The impact on the main plasma parameters was minor and no disruptions occurred. The W-melt gradually moved along the leading edge towards the high-field side, driven by j × B forces. The evaporation rate determined from spectroscopy is 100 times less than expected from steady state melting and is thus consistent only with transient melting during the individual ELMs. Analysis of IR data and spectroscopy together with modelling using the MEMOS code Bazylev et al 2009 J. Nucl. Mater. 390-391 810-13 point to transient melting as the main process. 3D MEMOS simulations on the consequences of multiple ELMs on damage of tungsten castellated armour have been performed. These experiments provide the first experimental evidence for the absence of significant melt splashing at transient events resembling mitigated ELMs on ITER and establish a key experimental benchmark for the MEMOS code.

  11. Very short-term reactive forecasting of the solar ultraviolet index using an extreme learning machine integrated with the solar zenith angle.

    PubMed

    Deo, Ravinesh C; Downs, Nathan; Parisi, Alfio V; Adamowski, Jan F; Quilty, John M

    2017-05-01

    Exposure to erythemally-effective solar ultraviolet radiation (UVR) that contributes to malignant keratinocyte cancers and associated health-risk is best mitigated through innovative decision-support systems, with global solar UV index (UVI) forecast necessary to inform real-time sun-protection behaviour recommendations. It follows that the UVI forecasting models are useful tools for such decision-making. In this study, a model for computationally-efficient data-driven forecasting of diffuse and global very short-term reactive (VSTR) (10-min lead-time) UVI, enhanced by drawing on the solar zenith angle (θ s ) data, was developed using an extreme learning machine (ELM) algorithm. An ELM algorithm typically serves to address complex and ill-defined forecasting problems. UV spectroradiometer situated in Toowoomba, Australia measured daily cycles (0500-1700h) of UVI over the austral summer period. After trialling activations functions based on sine, hard limit, logarithmic and tangent sigmoid and triangular and radial basis networks for best results, an optimal ELM architecture utilising logarithmic sigmoid equation in hidden layer, with lagged combinations of θ s as the predictor data was developed. ELM's performance was evaluated using statistical metrics: correlation coefficient (r), Willmott's Index (WI), Nash-Sutcliffe efficiency coefficient (E NS ), root mean square error (RMSE), and mean absolute error (MAE) between observed and forecasted UVI. Using these metrics, the ELM model's performance was compared to that of existing methods: multivariate adaptive regression spline (MARS), M5 Model Tree, and a semi-empirical (Pro6UV) clear sky model. Based on RMSE and MAE values, the ELM model (0.255, 0.346, respectively) outperformed the MARS (0.310, 0.438) and M5 Model Tree (0.346, 0.466) models. Concurring with these metrics, the Willmott's Index for the ELM, MARS and M5 Model Tree models were 0.966, 0.942 and 0.934, respectively. About 57% of the ELM model's absolute errors were small in magnitude (±0.25), whereas the MARS and M5 Model Tree models generated 53% and 48% of such errors, respectively, indicating the latter models' errors to be distributed in larger magnitude error range. In terms of peak global UVI forecasting, with half the level of error, the ELM model outperformed MARS and M5 Model Tree. A comparison of the magnitude of hourly-cumulated errors of 10-min lead time forecasts for diffuse and global UVI highlighted ELM model's greater accuracy compared to MARS, M5 Model Tree or Pro6UV models. This confirmed the versatility of an ELM model drawing on θ s data for VSTR forecasting of UVI at near real-time horizon. When applied to the goal of enhancing expert systems, ELM-based accurate forecasts capable of reacting quickly to measured conditions can enhance real-time exposure advice for the public, mitigating the potential for solar UV-exposure-related disease. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.

  12. Using Geophysics to Define Hydrostratigraphic Units in the Edwards and Trinity Aquifers, Texas

    NASA Astrophysics Data System (ADS)

    Smith, B. D.; Blome, C. D.; Clark, A. K.; Kress, W.; Smith, D. V.

    2007-05-01

    Airborne and ground geophysical surveys conducted in Uvalde, Medina, and northern Bexar counties, Texas, can be used to define and characterize hydrostratigraphic units of the Edwards and Trinity aquifers. Airborne magnetic surveys have defined numerous Cretaceous intrusive stocks and laccoliths, mainly in Uvalde County, that influence local hydrology and perhaps regional ground-water flow paths. Depositional environments in the aquifers can be classified as shallow water platforms (San Marcos Platform, Edwards Group), shoal and reef facies (Devils River Trend, Devils River Formation), and deeper water basins (Maverick Basin, West Nueces, McKnight, and Salmon Peak Formations). Detailed airborne and ground electromagnetic surveys have been conducted over the Edwards aquifer catchment zone (exposed Trinity aquifer rocks), recharge zone (exposed Edwards aquifer rocks), and artesian zone (confined Edwards) in the Seco Creek area (northeast Uvalde and Medina Counties; Devils River Trend). These geophysical survey data have been used to divide the Edwards exposed within the Balcones fault zone into upper and lower hydrostratigraphic units. Although both units are high electrical resistivity, the upper unit has slightly lower resistivity than the lower unit. The Georgetown Formation, at the top of the Edwards Group has a moderate resistivity. The formations that comprise the upper confining units to the Edwards aquifer rocks have varying resistivities. The Eagleford and Del Rio Groups (mainly clays) have very low resistivities and are excellent electrical marker beds in the Seco Creek area. The Buda Limestone is characterized by high resistivities. Moderate resistivities characterize the Austin Group rocks (mainly chalk). The older Trinity aquifer, underlying the Edwards aquifer rocks, is characterized by less limestone (electrically resistive or low conductivity units) and greater quantities of mudstones (electrically conductive or low resistivity units). In the western area (Devils River Trend and Maverick Basin) of the Trinity aquifer system there are well-defined collapse units and features that are marked by moderate resistivities bracketed by resistive limestone and conductive mudstone of the Glen Rose Limestone. In the central part of the aquifer (San Marcos Platform) the Trinity's lithologies are divided into upper and lower units with further subdivisions into hydrostratigraphic units. These hydrostratigraphic units are well mapped by an airborne electromagnetic survey in Bexar County. Electrical properties of the Edwards aquifer also vary across the fresh-saline water interface where ground and borehole electrical surveys have been conducted. The saline- saturated Edwards is predictably more conductive than the fresh-water saturated rocks. Similar fresh-saline water interfaces exist within the upper confining units of the Edwards aquifer (Carrizo-Wilcox aquifer) and the Trinity aquifer rocks.

  13. The fecundity of fork-tailed threadfin bream (Nemipterus furcosus) in Bangka, Bangka Belitung

    NASA Astrophysics Data System (ADS)

    Utami, E.; Safitriyani, E.; Gatra Persada, Leo

    2018-04-01

    Fork-tailed threadfin bream (Nemipterus furcosus) is one of important economic fishes in Bangka. The sustainability of fork-tailed threadfin bream is threatened by degradation of natural habitat. Information of reproductive is needed for further management. The objective of this study was to examine fecundity of fork-tailed threadfin bream. The mean values of temperature was 28.83 ± 0,37°C, respectively. Sex ratio during sampling showed that female fork-tailed threadfin bream greater than male population. Berried female fork-tailed threadfin bream found from March until November. The greatest number of berried female fork-tailed threadfin bream showed in July with berried female value of 25. Fork-tailed threadfin bream fecundity was 19951 and 66628, respectively. The fecundity data can be used to access the reproductive potential of fish stock and also as an assessment on stock size of their natural population.

  14. Inter-Fork Strand Annealing causes genomic deletions during the termination of DNA replication.

    PubMed

    Morrow, Carl A; Nguyen, Michael O; Fower, Andrew; Wong, Io Nam; Osman, Fekret; Bryer, Claire; Whitby, Matthew C

    2017-06-06

    Problems that arise during DNA replication can drive genomic alterations that are instrumental in the development of cancers and many human genetic disorders. Replication fork barriers are a commonly encountered problem, which can cause fork collapse and act as hotspots for replication termination. Collapsed forks can be rescued by homologous recombination, which restarts replication. However, replication restart is relatively slow and, therefore, replication termination may frequently occur by an active fork converging on a collapsed fork. We find that this type of non-canonical fork convergence in fission yeast is prone to trigger deletions between repetitive DNA sequences via a mechanism we call Inter-Fork Strand Annealing (IFSA) that depends on the recombination proteins Rad52, Exo1 and Mus81, and is countered by the FANCM-related DNA helicase Fml1. Based on our findings, we propose that IFSA is a potential threat to genomic stability in eukaryotes.

  15. Termination of DNA replication forks: "Breaking up is hard to do".

    PubMed

    Bailey, Rachael; Priego Moreno, Sara; Gambus, Agnieszka

    2015-01-01

    To ensure duplication of the entire genome, eukaryotic DNA replication initiates from thousands of replication origins. The replication forks move through the chromatin until they encounter forks from neighboring origins. During replication fork termination forks converge, the replisomes disassemble and topoisomerase II resolves the daughter DNA molecules. If not resolved efficiently, terminating forks result in genomic instability through the formation of pathogenic structures. Our recent findings shed light onto the mechanism of replisome disassembly upon replication fork termination. We have shown that termination-specific polyubiquitylation of the replicative helicase component - Mcm7, leads to dissolution of the active helicase in a process dependent on the p97/VCP/Cdc48 segregase. The inhibition of terminating helicase disassembly resulted in a replication termination defect. In this extended view we present hypothetical models of replication fork termination and discuss remaining and emerging questions in the DNA replication termination field.

  16. Semiochemical-mediated flight strategies of two invasive elm bark beetles: A potential factor in competitive displacement

    Treesearch

    Jana C. Lee; Shakeeb M. Hamud; Jose F. Negron; Jeffrey J. Witcosky; Steven J. Seybold

    2010-01-01

    A seven-state survey showed that the recently detected invasive Asian banded elm bark beetle, Scolytus schevyrewi Semenov, was abundant in areas of Colorado and Wyoming, whereas the long-established European elm bark beetle, S. multistriatus (Marsham), was not as abundant. In one of a series of studies to evaluate whether S. schevyrewi is competitively displacing S....

  17. Host Acceptance and Larval Competition between the Invasive Banded and European Elm Bark Beetles, Scolytus schevyrewi and S. multistriatus (Coleoptera: Scolytidae): Potential Mechanisms for Competitive Displacement

    USDA-ARS?s Scientific Manuscript database

    A recent survey revealed that the newly invasive banded elm bark beetle, Scolytus schevyrewi, was much more abundant than the long-established European elm bark beetle, S. multistriatus, in areas of Colorado and Wyoming, USA. This study sought to determine whether competitive displacement of S. mul...

  18. Improving germination of red elm (Ulmus rubra), gray alder (Alnus incana), and buffaloberry (Shepherdia canadensis) seeds with gibberellic acid

    Treesearch

    Brenda Morales; Charles Barden; Cheryl Boyer; Jason Griffin; Lillian Fisher; Joni Thompson

    2012-01-01

    Red elm (Ulmus rubra), gray alder (Alnus incana), and buffaloberry (Shepherdia canadensis) are considered important plants for many Native American tribes in the United States. Native Americans use these 3 species for a variety of traditional and medicinal purposes. For example, red elm is still the preferred firewood for the cultural ceremonies of several tribes....

  19. Environmental Assessment for Tinker Aerospace Complex Tinker Air Force Base, Oklahoma

    DTIC Science & Technology

    2008-05-01

    Boutelova curtipendula silver bluestem Andropogon saccharoides slippery elm Ulmus rubra sugarberry Celtis laevigata switchgrass...areas; Crutcho Creek, Elm Creek, and Hog Creek. The Crutcho Creek drainage area consists of two additional water bodies, Kulhman Creek and Solider...Crutcho Creek flows to the north and discharges into the North Canadian River; the North Canadian River then discharges into the Arkansas River. Elm

  20. Balance of the stored energies sustained by the internal and edge transport barriers and effects of ELMs and L-H transitions in JT-60U

    NASA Astrophysics Data System (ADS)

    Kamada, Y.; Yoshida, M.; Sakamoto, Y.; Koide, Y.; Oyama, N.; Urano, H.; Kamiya, K.; Suzuki, T.; Isayama, A.; JT-60 Team

    2009-09-01

    To understand key physics processes determining radial profiles of the kinetic plasma parameters in the advanced tokamak operation scenarios, correlations between the edge transport barrier (ETB) and the internal transport barrier (ITB) have been studied in the JT-60U tokamak device. It has been found that the edge pedestal poloidal beta, βp-ped, increases almost linearly with the total poloidal beta, βp-tot, over a wide range of the plasma current for type I ELMing H-mode plasmas, and this dependence becomes stronger with increasing triangularity. This dependence is not due to the profile stiffness, since the dependence is the same regardless of the existence of ITB. As the stored energy inside the ITB-foot radius (WITB) increases, the total thermal stored energy (Wth) increases and then the pedestal stored energy (Wped) increases. On the other hand, as Wped increases, the ELM penetration expands more inwards and finally reaches the ITB-foot radius. At this situation, the ITB-foot radius cannot move outwards because of the erosion by ELMs. Then the fractions of WITB/Wth and Wped/Wth become almost constant. It has also been found that the type I ELM expels/decreases the edge toroidal momentum larger than the edge ion thermal energy. The ELM penetration for the toroidal rotation tends to be deeper than that for the ion temperature and can exceed the ITB-foot radius. The ELM penetration is deeper for CO-rotating plasmas than CTR rotating plasmas. In both cases, the ELM penetration is deeper in the order of the toroidal rotation (Vt), the ion temperature (Ti) and then the electron temperature (Te). The L-H transition also changes the Vt profile more significantly than the Ti profile. At the L-H transition, the pedestal Vt shifts into the CTR-direction deeply and suddenly without a change in Ti, and then the pedestal Vt grows further together with a growth of the pedestal Ti in a slower timescale. Such changes in Vt by ELMs and L-H transitions may affect degradation/evolution of ITBs.

  1. Comparison of heat flux measurement techniques during the DIII-D metal ring campaign

    NASA Astrophysics Data System (ADS)

    Barton, J. L.; Nygren, R. E.; Unterberg, E. A.; Watkins, J. G.; Makowski, M. A.; Moser, A.; Rudakov, D. L.; Buchenauer, D.

    2017-12-01

    The heat fluxes expected in the ITER divertor raise concerns about the damage tolerances of tungsten, especially due to thermal transients caused by edge localized modes (ELMs) as well as frequent temperature cycling from high to low extremes. Therefore we are motivated to understand the heat flux conditions that can cause not only enhanced erosion but also bulk thermo-mechanical damage to a tungsten divertor. For the metal ring campaign in DIII-D, tungsten-coated TZM tile inserts were installed making two toroidal arrays of metal tile inserts in the lower divertor. This study examines the deposited heat flux on these rings with embedded thermocouples (TCs) sampling at 10 kHz and compares them to Langmuir probe (LP) and infrared thermography (IRTV) heat flux measurements. We see agreement of the TC, LP, and IRTV data within 20% of the heat flux averaged over the entire discharge, and that all three diagnostics suggest parallel heat flux at the OSP location increases linearly with input heating power. The TC and LP heat flux time traces during the discharge trend together during large changes to the average heat flux. By subtracting the LP measured inter-ELM heat flux from TC data, using a rectangular ELM energy pulse shape, and taking the relative size and duration of each ELM from {{D}}α measurements, we extract the ELM heat fluxes from TC data. This over-estimates the IRTV measured ELM heat fluxes by a factor of 1.9, and could be due to the simplicity of the TC heat flux model and the assumed ELM energy pulse shape. ELM heat fluxes deposited on the inserts are used to model tungsten erosion in this campaign. These TC ELM heat flux estimates are used in addition to IRTV, especially in cases where the IRTV view to the metal ring is obstructed. We observe that some metal inserts were deformed due to exposed leading edges. The thermal conditions on these inserts are investigated with the thermal modeling code ABAQUS using our heat flux measurements when these edges were exposed. We discuss how the thermal cycling on the ends of the inserts caused this deformation.

  2. Sortal Concepts and Pragmatic Inference in Children's Early Quantification of Objects

    ERIC Educational Resources Information Center

    Srinivasan, Mahesh; Chestnut, Eleanor; Li, Peggy; Barner, David

    2013-01-01

    It is typically assumed that count nouns like "fork" act as logical sortals, specifying whether objects are countable units of a kind (e.g., that a whole fork counts as "one fork") or not (e.g., that a piece of a fork does not count as "one fork"). In four experiments, we provide evidence from linguistic and conceptual development that nouns do…

  3. 11. Photocopy of photograph (original copy in Edison collection). Photographer ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    11. Photocopy of photograph (original copy in Edison collection). Photographer and date unknown, although photo taken prior to 1930 reconstruction of Project flumes. VIEW OF ORIGINAL SOUTH FORK OF THE TULE RIVER MIDDLE FORK "BOX" WOOD FLUME BRANCH SHOWING NORTH FORK OF TULE RIVER MIDDLE FORK CROSSING. VIEW TO NORTHWEST. - Tule River Hydroelectric Project, Water Conveyance System, Middle Fork Tule River, Springville, Tulare County, CA

  4. Water-quality assessment of the Trinity River Basin, Texas - Review and analysis of available pesticide information, 1968-91

    USGS Publications Warehouse

    Ulery, R.L.; Brown, M.F.

    1995-01-01

    Review of all available data showed that pesticides were detected to a substantial degree in various sample media over the time period covered by this report. The authors were able to locate little pesticide-sample data for ground water or for tributary streams because sampling efforts historically have been concentrated on the mainstem Trinity River.

  5. Extensional faulting in the southern Klamath Mountains, California

    USGS Publications Warehouse

    Schweickert, R.A.; Irwin, W.P.

    1989-01-01

    Large northeast striking normal faults in the southern Klamath Mountains may indicate that substantial crustal extension occurred during Tertiary time. Some of these faults form grabens in the Jurassic and older bedrock of the province. The grabens contain continental Oligocene or Miocene deposits (Weaverville Formation), and in two of them the Oligocene or Miocene is underlain by Lower Cretaceous marine formations (Great Valley sequence). At the La Grange gold placer mine the Oligocene or Miocene strata dip northwest into the gently southeast dipping mylonitic footwall surface of the La Grange fault. The large normal displacement required by the relations at the La Grange mine is also suggested by omission of several kilometers of structural thickness of bedrock units across the northeast continuation of the La Grange fault, as well as by significant changes in bedrock across some northeast striking faults elsewhere in the Central Metamorphic and Eastern Klamath belts. The Trinity ultramafic sheet crops out in the Eastern Klamath terrane as part of a broad northeast trending arch that may be structurally analogous to the domed lower plate of metamorphic core complexes found in eastern parts of the Cordillera. The northeast continuation of the La Grange fault bounds the southeastern side of the Trinity arch in the Eastern Klamath terrane and locally cuts out substantial lower parts of adjacent Paleozoic strata of the Redding section. Faults bounding the northwestem side of the Trinity arch generally trend northeast and juxtapose stacked thrust sheets of lower Paleozoic strata of the Yreka terrane against the Trinity ultramafic sheet. Geometric relations suggest that the Tertiary extension of the southern Klamath Mountains was in NW-SE directions and that the Redding section and the southern part of the Central Metamorphic terrane may be a large Tertiary allochthon detached from the Trinity ultramafic sheet. Paleomagnetic data indicate a lack of rotation about a vertical axis during the extension. We propose that the Trinity ultramafic sheet is structurally analogous to a metamorphic core complex; if so, it is the first core complex to be described that involves ultramafic rocks. We infer that Mesozoic terrane accretion produced a large gravitational instability in the crust that spread laterally during Tertiary extension

  6. Grand Forks/East Grand Forks ITS strategy plan

    DOT National Transportation Integrated Search

    2001-01-15

    The Grand Forks/East Grand Forks (GF/EGF) Area's Intelligent Transportation Systems (ITS) Strategy Plan is an effort by the GF/EGF Metropolitan Planning Organization (MPO) and its partners to develop a plan for deploying Intelligent Transportation Sy...

  7. 77 FR 39675 - Wallowa-Whitman National Forest, Baker County, OR; North Fork Burnt River Mining

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-05

    ...-Whitman National Forest, Baker County, OR; North Fork Burnt River Mining AGENCY: Forest Service, USDA... North Fork Burnt River Mining Record of Decision will replace and supercede the 2004 North Fork Burnt...

  8. Replication stress-induced chromosome breakage is correlated with replication fork progression and is preceded by single-stranded DNA formation.

    PubMed

    Feng, Wenyi; Di Rienzi, Sara C; Raghuraman, M K; Brewer, Bonita J

    2011-10-01

    Chromosome breakage as a result of replication stress has been hypothesized to be the direct consequence of defective replication fork progression, or "collapsed" replication forks. However, direct and genome-wide evidence that collapsed replication forks give rise to chromosome breakage is still lacking. Previously we showed that a yeast replication checkpoint mutant mec1-1, after transient exposure to replication impediment imposed by hydroxyurea (HU), failed to complete DNA replication, accumulated single-stranded DNA (ssDNA) at the replication forks, and fragmented its chromosomes. In this study, by following replication fork progression genome-wide via ssDNA detection and by direct mapping of chromosome breakage after HU exposure, we have tested the hypothesis that the chromosome breakage in mec1 cells occurs at collapsed replication forks. We demonstrate that sites of chromosome breakage indeed correlate with replication fork locations. Moreover, ssDNA can be detected prior to chromosome breakage, suggesting that ssDNA accumulation is the common precursor to double strand breaks at collapsed replication forks.

  9. Three dimensional nonlinear simulations of edge localized modes on the EAST tokamak using BOUT++ code

    NASA Astrophysics Data System (ADS)

    Liu, Z. X.; Xu, X. Q.; Gao, X.; Xia, T. Y.; Joseph, I.; Meyer, W. H.; Liu, S. C.; Xu, G. S.; Shao, L. M.; Ding, S. Y.; Li, G. Q.; Li, J. G.

    2014-09-01

    Experimental measurements of edge localized modes (ELMs) observed on the EAST experiment are compared to linear and nonlinear theoretical simulations of peeling-ballooning modes using the BOUT++ code. Simulations predict that the dominant toroidal mode number of the ELM instability becomes larger for lower current, which is consistent with the mode structure captured with visible light using an optical CCD camera. The poloidal mode number of the simulated pressure perturbation shows good agreement with the filamentary structure observed by the camera. The nonlinear simulation is also consistent with the experimentally measured energy loss during an ELM crash and with the radial speed of ELM effluxes measured using a gas puffing imaging diagnostic.

  10. Effect of ultrasonic tip and root-end filling material on bond strength.

    PubMed

    Vivan, Rodrigo Ricci; Guerreiro-Tanomaru, Juliane Maria; Bernardes, Ricardo Affonso; Reis, José Mauricio Santos Nunes; Hungaro Duarte, Marco Antonio; Tanomaru-Filho, Mário

    2016-11-01

    The objective of this study was to evaluate the bond strength of three root-end filling materials (MTAA-MTA Angelus, MTAS-experimental MTA Sealer, and ZOE- zinc oxide and eugenol cement) in retrograde preparations performed with different ultrasonic tips (CVD, Trinity, and Satelec). Ninety 2-mm root sections from single-rooted human teeth were used. The retrograde cavities were prepared by using the ultrasonic tips, coupled to a device for position standardization. The specimens were randomly divided into nine groups: CVD MTAA; CVD MTAS; CVD ZOE; Trinity MTAA; Trinity MTAS; Trinity ZOE; Satelec MTAA; Satelec MTAS; Satelec ZOE. Each resin disc/dentin/root-end filling material was placed in the machine to perform the push-out test. The specimens were examined in a stereomicroscope to evaluate the type of failure. Data were submitted to statistical analysis using ANOVA and Tukey tests (α = 0.05). The highest bond strength was observed for the CVD tip irrespective of the material used (P < 0.05). There was no significant difference for the Trinity TU-18 diamond and S12 Satelec tips (P > 0.05). MTAA and MTAS showed highest bond strength. The most common type of failure was adhesion between the filling material and dentin wall, except for ZOE, where mixed failure was predominant. The CVD tip favored higher bond strength of the root-end filling materials. MTA Angelus and experimental MTAS presented bond strength to dentin prepared with ultrasonic tips. Root-end preparation with the CVD tip positively influences the bond strength of root-end filling materials. MTA Angelus and experimental MTAS present bond strength to be used as root-end filling materials.

  11. General perspective view of the North Fork Butter Creek Bridge, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    General perspective view of the North Fork Butter Creek Bridge, view looking southwest - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  12. Approach view of the North Fork Butter Creek Bridge, view ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Approach view of the North Fork Butter Creek Bridge, view looking south - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  13. General perspective view of the North Fork Butter Creek Bridge, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    General perspective view of the North Fork Butter Creek Bridge, view looking north - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  14. Elevation view of the North Fork Butter Creek Bridge, view ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Elevation view of the North Fork Butter Creek Bridge, view looking west - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  15. Approach view of the North Fork Butter Creek Bridge, view ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Approach view of the North Fork Butter Creek Bridge, view looking north - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  16. Detail perspective view of the North Fork Butter Creek Bridge, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail perspective view of the North Fork Butter Creek Bridge, view looking southwest - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  17. General perspective view of the North Fork Butter Creek Bridge, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    General perspective view of the North Fork Butter Creek Bridge, view looking south - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  18. THE FORK AND THE KINASE: A DNA REPLICATION TALE FROM A CHK1 PERSPECTIVE

    PubMed Central

    González Besteiro, Marina A.; Gottifredi, Vanesa

    2014-01-01

    Replication fork progression is being continuously hampered by exogenously introduced and naturally occurring DNA lesions and other physical obstacles. The checkpoint kinase 1 (Chk1) is activated at replication forks that encounter damaged-DNA. Chk1 inhibits the initiation of new replication factories and stimulates the firing of dormant origins (those in the vicinity of stalled forks). Chk1 also avoids fork collapse into DSBs (double strand breaks) and promotes fork elongation. At the molecular level, the current model considers stalled forks as the site of Chk1 activation and the nucleoplasm as the location where Chk1 phosphorylates target proteins. This model certainly serves to explain how Chk1 modulates origin firing, but how Chk1 controls the fate of stalled forks is less clear. Interestingly, recent reports demonstrating that Chk1 phosphorylates chromatin-bound proteins and even holds kinase-independent functions might shed light on how Chk1 contributes to the elongation of damaged DNA. Such findings unveil a puzzling connection between Chk1 and DNA-lesion bypass, which might be central to promoting fork elongation and checkpoint attenuation. In summary, the multifaceted and versatile functions of Chk1 at ongoing forks and replication origins determine the extent and quality of the cellular response to replication stress. PMID:25795119

  19. Experimental validation of an analytical kinetic model for edge-localized modes in JET-ITER-like wall

    NASA Astrophysics Data System (ADS)

    Guillemaut, C.; Metzger, C.; Moulton, D.; Heinola, K.; O’Mullane, M.; Balboa, I.; Boom, J.; Matthews, G. F.; Silburn, S.; Solano, E. R.; contributors, JET

    2018-06-01

    The design and operation of future fusion devices relying on H-mode plasmas requires reliable modelling of edge-localized modes (ELMs) for precise prediction of divertor target conditions. An extensive experimental validation of simple analytical predictions of the time evolution of target plasma loads during ELMs has been carried out here in more than 70 JET-ITER-like wall H-mode experiments with a wide range of conditions. Comparisons of these analytical predictions with diagnostic measurements of target ion flux density, power density, impact energy and electron temperature during ELMs are presented in this paper and show excellent agreement. The analytical predictions tested here are made with the ‘free-streaming’ kinetic model (FSM) which describes ELMs as a quasi-neutral plasma bunch expanding along the magnetic field lines into the Scrape-Off Layer without collisions. Consequences of the FSM on energy reflection and deposition on divertor targets during ELMs are also discussed.

  20. Exploring Short Linear Motifs Using the ELM Database and Tools.

    PubMed

    Gouw, Marc; Sámano-Sánchez, Hugo; Van Roey, Kim; Diella, Francesca; Gibson, Toby J; Dinkel, Holger

    2017-06-27

    The Eukaryotic Linear Motif (ELM) resource is dedicated to the characterization and prediction of short linear motifs (SLiMs). SLiMs are compact, degenerate peptide segments found in many proteins and essential to almost all cellular processes. However, despite their abundance, SLiMs remain largely uncharacterized. The ELM database is a collection of manually annotated SLiM instances curated from experimental literature. In this article we illustrate how to browse and search the database for curated SLiM data, and cover the different types of data integrated in the resource. We also cover how to use this resource in order to predict SLiMs in known as well as novel proteins, and how to interpret the results generated by the ELM prediction pipeline. The ELM database is a very rich resource, and in the following protocols we give helpful examples to demonstrate how this knowledge can be used to improve your own research. © 2017 by John Wiley & Sons, Inc. Copyright © 2017 John Wiley & Sons, Inc.

  1. BELM: Bayesian extreme learning machine.

    PubMed

    Soria-Olivas, Emilio; Gómez-Sanchis, Juan; Martín, José D; Vila-Francés, Joan; Martínez, Marcelino; Magdalena, José R; Serrano, Antonio J

    2011-03-01

    The theory of extreme learning machine (ELM) has become very popular on the last few years. ELM is a new approach for learning the parameters of the hidden layers of a multilayer neural network (as the multilayer perceptron or the radial basis function neural network). Its main advantage is the lower computational cost, which is especially relevant when dealing with many patterns defined in a high-dimensional space. This brief proposes a bayesian approach to ELM, which presents some advantages over other approaches: it allows the introduction of a priori knowledge; obtains the confidence intervals (CIs) without the need of applying methods that are computationally intensive, e.g., bootstrap; and presents high generalization capabilities. Bayesian ELM is benchmarked against classical ELM in several artificial and real datasets that are widely used for the evaluation of machine learning algorithms. Achieved results show that the proposed approach produces a competitive accuracy with some additional advantages, namely, automatic production of CIs, reduction of probability of model overfitting, and use of a priori knowledge.

  2. Pedestal bifurcation and resonant field penetration at the threshold of edge-localized mode suppression in the DIII-D Tokamak.

    PubMed

    Nazikian, R; Paz-Soldan, C; Callen, J D; deGrassie, J S; Eldon, D; Evans, T E; Ferraro, N M; Grierson, B A; Groebner, R J; Haskey, S R; Hegna, C C; King, J D; Logan, N C; McKee, G R; Moyer, R A; Okabayashi, M; Orlov, D M; Osborne, T H; Park, J-K; Rhodes, T L; Shafer, M W; Snyder, P B; Solomon, W M; Strait, E J; Wade, M R

    2015-03-13

    Rapid bifurcations in the plasma response to slowly varying n=2 magnetic fields are observed as the plasma transitions into and out of edge-localized mode (ELM) suppression. The rapid transition to ELM suppression is characterized by an increase in the toroidal rotation and a reduction in the electron pressure gradient at the top of the pedestal that reduces the perpendicular electron flow there to near zero. These events occur simultaneously with an increase in the inner-wall magnetic response. These observations are consistent with strong resonant field penetration of n=2 fields at the onset of ELM suppression, based on extended MHD simulations using measured plasma profiles. Spontaneous transitions into (and out of) ELM suppression with a static applied n=2 field indicate competing mechanisms of screening and penetration of resonant fields near threshold conditions. Magnetic measurements reveal evidence for the unlocking and rotation of tearinglike structures as the plasma transitions out of ELM suppression.

  3. Rule Extraction Based on Extreme Learning Machine and an Improved Ant-Miner Algorithm for Transient Stability Assessment.

    PubMed

    Li, Yang; Li, Guoqing; Wang, Zhenhao

    2015-01-01

    In order to overcome the problems of poor understandability of the pattern recognition-based transient stability assessment (PRTSA) methods, a new rule extraction method based on extreme learning machine (ELM) and an improved Ant-miner (IAM) algorithm is presented in this paper. First, the basic principles of ELM and Ant-miner algorithm are respectively introduced. Then, based on the selected optimal feature subset, an example sample set is generated by the trained ELM-based PRTSA model. And finally, a set of classification rules are obtained by IAM algorithm to replace the original ELM network. The novelty of this proposal is that transient stability rules are extracted from an example sample set generated by the trained ELM-based transient stability assessment model by using IAM algorithm. The effectiveness of the proposed method is shown by the application results on the New England 39-bus power system and a practical power system--the southern power system of Hebei province.

  4. ELM Triggering with the New PPPL Lithium Granular Injector

    NASA Astrophysics Data System (ADS)

    Mansfield, D. K.; Roquemore, A. L.; Maingi, R.; Hu, J. S.; Liang, Y.; Sun, Z.; Zhang, L.; Zou, G.

    2012-10-01

    A Li granular injector based on a high-speed rotating impeller has been developed at PPPL. The injector is capable of injecting spherical particles with diameters up to 1.3 mm and velocities of up to 100 m/s and has several possible applications. Primarily, the injector was developed as a tool to induce ELMs for ELM pacing experiments in plasmas operating in the H-mode. It can also operate as a real-time wall conditioning tool or as a method to resupply Li during a discharge to devices where Li is applied to the PFC's prior to a discharge. The injector is also capable of horizontally injecting small dust particles of any variety for plasma-dust transport studies. The first injector has recently been successfully installed on the EAST tokamak in Hefei, China where ELMs were induced with near 100% efficiency when 0.7mm spheres were injected at ˜ 40m/s into the midplane SOL. The injector will be described and supporting data for ELM triggering will be presented.

  5. Pedestal Bifurcation and Resonant Field Penetration at the Threshold of Edge-Localized Mode Suppression in the DIII-D Tokamak

    DOE PAGES

    Nazikian, Raffi; Paz-Soldan, Carlos; Callen, James D.; ...

    2015-03-12

    Rapid bifurcations in the plasma response to slowly varying n=2 magnetic fields are observed as the plasma transitions into and out of edge localized mode (ELM) suppression. The rapid transition to ELM suppression is characterized by an increase in the toroidal rotation and a reduction in the electron pressure gradient at the top of the pedestal which reduces the perpendicular electron flow to near zero. These events occur simultaneously with an increase in the inner wall magnetic response. These observations are consistent strong resonant field penetration of n=2 fields at the onset of ELM suppression, based on extended MHD simulationsmore » using measured plasma profiles. Spontaneous transitions into (and out of) ELM suppression with a static applied n=2 field indicate competing mechanisms of screening and penetration of resonant fields near threshold conditions. Magnetic measurements reveal evidence for the unlocking and rotation of tearing-like structures as the plasma transitions out of ELM suppression.« less

  6. The Glenwood Estate: our 32-year experience using Arbotect® 20-S to control Dutch elm disease

    Treesearch

    William L. MacDonald; Mark L. Double; Cameron M. Stauder; Kemp. Winfree

    2017-01-01

    We report a case study that demonstrates the successful use of the fungicide Arbotect® 20-S to protect American elms (Ulmus americana) from Dutch elm disease at a historic site in Charleston, WV. Standard injection protocols were used every 3 to 4 years to deliver the chemical into the root flares. Twelve of the original 16 trees remain 34 years...

  7. Archeology and Native American Religion at the Leon River Medicine Wheel.

    DTIC Science & Technology

    1996-02-01

    varieties of plants. The eastern side of including pecan (Carya illinoinensis), slippery elm the facility (East Range) is typified by dense (Ulmus rubra...southern part of the Cross Timbers and Prairies texana), and cedar elm (Ulmus crassifolia). A Vegetation Area. Alired and Mitchell (1955) term variety of...south (West Fort americana), American elm (Ulmus americana), Hood) are generally more open, ranging from TRC MARIAH ASSOCIATES, INC. (662-21

  8. The Extent of Hybridization and Its Impact on the Genetic Diversity and Population Structure of an Invasive Tree, Ulmus Pumila (Ulmaceae)

    USDA-ARS?s Scientific Manuscript database

    Siberian elm (Ulmus pumila L.), native to East Asia, was introduced in the U.S. in the 1900’s because of its high tolerance to Dutch elm disease (DED). Siberian elm has spread following its introduction and has now become one of the most invasive woody species in the U.S., alongside Russian olive a...

  9. Modeling impurity production and transport during ELM transients in a DIII-D lower single null configuration.

    NASA Astrophysics Data System (ADS)

    Hogan, J.; Fenstermacher, M.; Groth, M.; West, P.; Coster, D.; Thomas, P.

    2003-10-01

    Better understanding of carbon production and eventual pathways is an important need for ITER. ELM events can provide a significant carbon source, and small scale experiments predict significant dependence of C production rates on incident deuterium flux and surface temperature, quantities which change significantly during an ELM event. Thus, development of better quantitative models has been hampered by lack of sufficient time resolution during ELMs. Recent progress on DIII-D has significantly improved the spectroscopic resolution [1, 2]. Measured CIII evolution during low- and high-density DIII-D LSN ELMy H-modes (type I and type I-III, respectively) has been compared with modeling using the solps5.0/Eirene99 coupled edge code, and the CASTEM- 2000 3-D, time dependent thermal analysis code. The latter provides time-resolved absolute surface temperature distributions for the cases described in [2]. Comparison with observations using the Roth et al annealing model for chemical sputtering finds qualitative agreement. However, the transition in ELM type/frequency as density increases is the most important factor, and this is an input to the calculation given the present state of first principles ELM models. [1] M Fenstermacher et al EPS2003 [2] M Groth et al J Nucl Mater 2003

  10. How to assess the efficiency of synchronization experiments in tokamaks

    NASA Astrophysics Data System (ADS)

    Murari, A.; Craciunescu, T.; Peluso, E.; Gelfusa, M.; Lungaroni, M.; Garzotti, L.; Frigione, D.; Gaudio, P.; Contributors, JET

    2016-07-01

    Control of instabilities such as ELMs and sawteeth is considered an important ingredient in the development of reactor-relevant scenarios. Various forms of ELM pacing have been tried in the past to influence their behavior using external perturbations. One of the main problems with these synchronization experiments resides in the fact that ELMs are periodic or quasi-periodic in nature. Therefore, after any pulsed perturbation, if one waits long enough, an ELM is always bound to occur. To evaluate the effectiveness of ELM pacing techniques, it is crucial to determine an appropriate interval over which they can have a real influence and an effective triggering capability. In this paper, three independent statistical methods are described to address this issue: Granger causality, transfer entropy and recurrence plots. The obtained results for JET with the ITER-like wall (ILW) indicate that the proposed techniques agree very well and provide much better estimates than the traditional heuristic criteria reported in the literature. Moreover, their combined use allows for the improvement of the time resolution of the assessment and determination of the efficiency of the pellet triggering in different phases of the same discharge. Therefore, the developed methods can be used to provide a quantitative and statistically robust estimate of the triggering efficiency of ELM pacing under realistic experimental conditions.

  11. Measured vs. Predicted Pedestal Pressure During RMP ELM Control in DIII-D

    NASA Astrophysics Data System (ADS)

    Zywicki, Bailey; Fenstermacher, Max; Groebner, Richard; Meneghini, Orso

    2017-10-01

    From database analysis of DIII-D plasmas with Resonant Magnetic Perturbations (RMPs) for ELM control, we will compare the experimental pedestal pressure (p_ped) to EPED code predictions and present the dependence of any p_ped differences from EPED on RMP parameters not included in the EPED model e.g. RMP field strength, toroidal and poloidal spectrum etc. The EPED code, based on Peeling-Ballooning and Kinetic Ballooning instability constraints, will also be used by ITER to predict the H-mode p_ped without RMPs. ITER plans to use RMPs as an effective ELM control method. The need to control ELMs in ITER is of the utmost priority, as it directly correlates to the lifetime of the plasma facing components. An accurate means of determining the impact of RMP ELM control on the p_ped is needed, because the device fusion power is strongly dependent on p_ped. With this new collection of data, we aim to provide guidance to predictions of the ITER pedestal during RMP ELM control that can be incorporated in a future predictive code. Work supported in part by US DoE under the Science Undergraduate Laboratory Internship (SULI) program and under DE-FC02-04ER54698, and DE-AC52-07NA27344.

  12. Simultaneous induction of jasmonic acid and disease-responsive genes signifies tolerance of American elm to Dutch elm disease

    PubMed Central

    Sherif , S. M.; Shukla, M. R.; Murch, S. J.; Bernier, L.; Saxena, P. K.

    2016-01-01

    Dutch elm disease (DED), caused by three fungal species in the genus Ophiostoma, is the most devastating disease of both native European and North American elm trees. Although many tolerant cultivars have been identified and released, the tolerance mechanisms are not well understood and true resistance has not yet been achieved. Here we show that the expression of disease-responsive genes in reactions leading to tolerance or susceptibility is significantly differentiated within the first 144 hours post-inoculation (hpi). Analysis of the levels of endogenous plant defense molecules such as jasmonic acid (JA) and salicylic acid (SA) in tolerant and susceptible American elm saplings suggested SA and methyl-jasmonate as potential defense response elicitors, which was further confirmed by field observations. However, the tolerant phenotype can be best characterized by a concurrent induction of JA and disease-responsive genes at 96 hpi. Molecular investigations indicated that the expression of fungal genes (i.e. cerato ulmin) was also modulated by endogenous SA and JA and this response was unique among aggressive and non-aggressive fungal strains. The present study not only provides better understanding of tolerance mechanisms to DED, but also represents a first, verified template for examining simultaneous transcriptomic changes during American elm-fungus interactions. PMID:26902398

  13. Assessment of hand-transmitted vibration exposure from motorized forks used for beach-cleaning operations.

    PubMed

    McDowell, Thomas W; Welcome, Daniel E; Warren, Christopher; Xu, Xueyan S; Dong, Ren G

    2013-01-01

    Motorized vibrating manure forks were used in beach-cleaning operations following the massive Deepwater Horizon oil spill in the Gulf of Mexico during the summer of 2010. The objectives of this study were to characterize the vibration emissions of these motorized forks and to provide a first approximation of hand-transmitted vibration exposures to workers using these forks for beach cleaning. Eight operators were recruited to operate the motorized forks during this laboratory study. Four fork configurations were used in the study; two motor speeds and two fork basket options were evaluated. Accelerations were measured near each hand as the operators completed the simulated beach-cleaning task. The dominant vibration frequency for these tools was identified to be around 20 Hz. Because acceleration was found to increase with motor speed, workers should consider operating these tools with just enough speed to get the job done. These forks exhibited considerable acceleration magnitudes when unloaded. The study results suggest that the motor should not be operated with the fork in the unloaded state. Anti-vibration gloves are not effective at attenuating the vibration frequencies produced by these forks, and they may even amplify the transmitted vibration and increase hand/arm fatigue. While regular work gloves are suitable, vibration-reducing gloves may not be appropriate for use with these tools. These considerations may also be generally applicable for the use of motorized forks in other workplace environments.

  14. Geomorphic mapping to support river restoration on the Trinity River downstream from Lewiston Dam, California, 1980-2011

    USGS Publications Warehouse

    Curtis, Jennifer A.; Guerrero, Timothy M.

    2015-01-01

    Historic land use, dam construction, water storage, and flow diversions in the Trinity River watershed have resulted in downstream geomorphic change, loss of salmonid habitat, and declines in salmonid populations. The USGS in cooperation with the Trinity River Restoration Program, a multi-agency partnership tasked with implementing federally mandated restoration, completed a geomorphic change assessment to inform the planning process for future restoration work. This report documents an ARCMAP geodatabase (v.10.0) containing geomorphic features digitized from a series of rectified orthophotographs (http://dx.doi.org/10.5066/F7TT4P04). Upland, riparian, and channel features were digitized from six available base images (1980, 1997, 2001, 2006, 2009, and 2011). This report describes the structure of the geodatabase and the methods used to delineate individual geomorphic features.

  15. LAMMPS Project Report for the Trinity KNL Open Science Period.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Moore, Stan Gerald; Thompson, Aidan P.; Wood, Mitchell

    LAMMPS is a classical molecular dynamics code (lammps.sandia.gov) used to model materials science problems at Sandia National Laboratories and around the world. LAMMPS was one of three Sandia codes selected to participate in the Trinity KNL (TR2) Open Science period. During this period, three different problems of interest were investigated using LAMMPS. The first was benchmarking KNL performance using different force field models. The second was simulating void collapse in shocked HNS energetic material using an all-atom model. The third was simulating shock propagation through poly-crystalline RDX energetic material using a coarse-grain model, the results of which were used inmore » an ACM Gordon Bell Prize submission. This report describes the results of these simulations, lessons learned, and some hardware issues found on Trinity KNL as part of this work.« less

  16. Child abuse potential in mothers with early life maltreatment, borderline personality disorder and depression.

    PubMed

    Dittrich, Katja; Boedeker, Katja; Kluczniok, Dorothea; Jaite, Charlotte; Hindi Attar, Catherine; Fuehrer, Daniel; Herpertz, Sabine C; Brunner, Romuald; Winter, Sibylle Maria; Heinz, Andreas; Roepke, Stefan; Heim, Christine; Bermpohl, Felix

    2018-05-24

    Early life maltreatment (ELM), borderline personality disorder (BPD) and major depressive disorder (MDD) have been shown to increase the potential of abuse. Emotion regulation is an identified mediator for the association of ELM and BPD with abuse potential. Until now, there has been no study to account for the co-occurrence of these risk factors in one analysis, although BPD and MDD are known as common sequelae of ELM. This is paired with a lack of studies investigating the effects of abuse potential on child well-being.AimsOur study aims at (a) disentangling the effects of maternal ELM, MDD and BPD on abuse potential; (b) exploring the role of emotion regulation as a mediator; and (c) testing for intergenerational effects of abuse potential on child psychopathology. The research design included 114 mothers with/without ELM, BPD and MDD in remission and their children, all of which were between 5 and 12 years of age. A path analysis was conducted to investigate the multiple associations between our variables. ELM, MDD and BPD were all associated with abuse potential, with emotion regulation acting as a mediator for BPD and MDD. Furthermore, an elevated abuse potential was related to higher psychopathology in the child. History of ELM as well as the common sequelae, BPD and MDD, pose risks for child abuse. Our findings suggest improvement of emotion regulation as a potential target for intervention programs. These programs should also aim at non-substantiated cases because even an elevated abuse potential affected child mental health.Declaration of interestNone.

  17. Note: Enhanced energy harvesting from low-frequency magnetic fields utilizing magneto-mechano-electric composite tuning-fork.

    PubMed

    Yang, Aichao; Li, Ping; Wen, Yumei; Yang, Chao; Wang, Decai; Zhang, Feng; Zhang, Jiajia

    2015-06-01

    A magnetic-field energy harvester using a low-frequency magneto-mechano-electric (MME) composite tuning-fork is proposed. This MME composite tuning-fork consists of a copper tuning fork with piezoelectric Pb(Zr(1-x)Ti(x))O3 (PZT) plates bonded near its fixed end and with NdFeB magnets attached at its free ends. Due to the resonance coupling between fork prongs, the MME composite tuning-fork owns strong vibration and high Q value. Experimental results show that the proposed magnetic-field energy harvester using the MME composite tuning-fork exhibits approximately 4 times larger maximum output voltage and 7.2 times higher maximum power than the conventional magnetic-field energy harvester using the MME composite cantilever.

  18. Edge profile analysis of Joint European Torus (JET) Thomson scattering data: Quantifying the systematic error due to edge localised mode synchronisation.

    PubMed

    Leyland, M J; Beurskens, M N A; Flanagan, J C; Frassinetti, L; Gibson, K J; Kempenaars, M; Maslov, M; Scannell, R

    2016-01-01

    The Joint European Torus (JET) high resolution Thomson scattering (HRTS) system measures radial electron temperature and density profiles. One of the key capabilities of this diagnostic is measuring the steep pressure gradient, termed the pedestal, at the edge of JET plasmas. The pedestal is susceptible to limiting instabilities, such as Edge Localised Modes (ELMs), characterised by a periodic collapse of the steep gradient region. A common method to extract the pedestal width, gradient, and height, used on numerous machines, is by performing a modified hyperbolic tangent (mtanh) fit to overlaid profiles selected from the same region of the ELM cycle. This process of overlaying profiles, termed ELM synchronisation, maximises the number of data points defining the pedestal region for a given phase of the ELM cycle. When fitting to HRTS profiles, it is necessary to incorporate the diagnostic radial instrument function, particularly important when considering the pedestal width. A deconvolved fit is determined by a forward convolution method requiring knowledge of only the instrument function and profiles. The systematic error due to the deconvolution technique incorporated into the JET pedestal fitting tool has been documented by Frassinetti et al. [Rev. Sci. Instrum. 83, 013506 (2012)]. This paper seeks to understand and quantify the systematic error introduced to the pedestal width due to ELM synchronisation. Synthetic profiles, generated with error bars and point-to-point variation characteristic of real HRTS profiles, are used to evaluate the deviation from the underlying pedestal width. We find on JET that the ELM synchronisation systematic error is negligible in comparison to the statistical error when assuming ten overlaid profiles (typical for a pre-ELM fit to HRTS profiles). This confirms that fitting a mtanh to ELM synchronised profiles is a robust and practical technique for extracting the pedestal structure.

  19. Dynamic ELM and divertor control using resonant toroidal multi-mode magnetic fields in DIII-D and EAST

    NASA Astrophysics Data System (ADS)

    Sun, Youwen

    2017-10-01

    A rotating n = 2 Resonant Magnetic Perturbation (RMP) field combined with a stationary n = 3 RMP field has validated predictions that access to ELM suppression can be improved, while divertor heat and particle flux can also be dynamically controlled in DIII-D. Recent observations in the EAST tokamak indicate that edge magnetic topology changes, due to nonlinear plasma response to magnetic perturbations, play a critical role in accessing ELM suppression. MARS-F code MHD simulations, which include the plasma response to the RMP, indicate the nonlinear transition to ELM suppression is optimized by configuring the RMP coils to drive maximal edge stochasticity. Consequently, mixed toroidal multi-mode RMP fields, which produce more densely packed islands over a range of additional rational surfaces, improve access to ELM suppression, and further spread heat loading on the divertor. Beneficial effects of this multi-harmonic spectrum on ELM suppression have been validated in DIII-D. Here, the threshold current required for ELM suppression with a mixed n spectrum, where part of the n = 3 RMP field is replaced by an n = 2 field, is smaller than the case with pure n = 3 field. An important further benefit of this multi-mode approach is that significant changes of 3D particle flux footprint profiles on the divertor are found in the experiment during the application of a rotating n = 2 RMP field superimposed on a static n = 3 RMP field. This result was predicted by modeling studies of the edge magnetic field structure using the TOP2D code which takes into account plasma response from MARS-F code. These results expand physics understanding and potential effectiveness of the technique for reliably controlling ELMs and divertor power/particle loading distributions in future burning plasma devices such as ITER. Work supported by USDOE under DE-FC02-04ER54698 and NNSF of China under 11475224.

  20. The coolest extremely low-mass white dwarfs

    NASA Astrophysics Data System (ADS)

    Calcaferro, Leila M.; Althaus, Leandro G.; Córsico, Alejandro H.

    2018-06-01

    Context. Extremely low-mass white dwarf (ELM WD; M⋆ ≲ 0.18-0.20 M⊙) stars are thought to be formed in binary systems via stable or unstable mass transfer. Although stable mass transfer predicts the formation of ELM WDs with thick hydrogen (H) envelopes that are characterized by dominant residual nuclear burning along the cooling branch, the formation of ELM WDs with thinner H envelopes from unstable mass loss cannot be discarded. Aims: We compute new evolutionary sequences for helium (He) core WD stars with thin H envelopes with the main aim of assessing the lowest Teff that could be reached by this type of stars. Methods: We generate a new grid of evolutionary sequences of He-core WD stars with thin H envelopes in the mass range from 0.1554 to 0.2025 M⊙, and assess the changes in both the cooling times and surface gravity induced by a reduction of the H envelope. We also determine, taking into account the predictions of progenitor evolution, the lowest Teff reached by the resulting ELM WDs. Results: We find that a slight reduction in the H envelope yields a significant increase in the cooling rate of ELM WDs. Because of this, ELM WDs with thin H envelopes could cool down to 2500 K, in contrast to their canonical counterparts that cool down to 7000 K. In addition, we find that a reduction of the thickness of the H envelope markedly increases the surface gravity (g) of these stars. Conclusions: If ELM WDs are formed with thin H envelopes, they could be detected at very low Teff. The detection of such cool ELM WDs would be indicative that they were formed with thin H envelopes, thus opening the possibility of placing constraints on the possible mechanisms of formation of this type of star. Last but not least, the increase in g due to the reduction of the H envelope leads to consequences in the spectroscopic determinations of these stars.

  1. Stream-flow forecasting using extreme learning machines: A case study in a semi-arid region in Iraq

    NASA Astrophysics Data System (ADS)

    Yaseen, Zaher Mundher; Jaafar, Othman; Deo, Ravinesh C.; Kisi, Ozgur; Adamowski, Jan; Quilty, John; El-Shafie, Ahmed

    2016-11-01

    Monthly stream-flow forecasting can yield important information for hydrological applications including sustainable design of rural and urban water management systems, optimization of water resource allocations, water use, pricing and water quality assessment, and agriculture and irrigation operations. The motivation for exploring and developing expert predictive models is an ongoing endeavor for hydrological applications. In this study, the potential of a relatively new data-driven method, namely the extreme learning machine (ELM) method, was explored for forecasting monthly stream-flow discharge rates in the Tigris River, Iraq. The ELM algorithm is a single-layer feedforward neural network (SLFNs) which randomly selects the input weights, hidden layer biases and analytically determines the output weights of the SLFNs. Based on the partial autocorrelation functions of historical stream-flow data, a set of five input combinations with lagged stream-flow values are employed to establish the best forecasting model. A comparative investigation is conducted to evaluate the performance of the ELM compared to other data-driven models: support vector regression (SVR) and generalized regression neural network (GRNN). The forecasting metrics defined as the correlation coefficient (r), Nash-Sutcliffe efficiency (ENS), Willmott's Index (WI), root-mean-square error (RMSE) and mean absolute error (MAE) computed between the observed and forecasted stream-flow data are employed to assess the ELM model's effectiveness. The results revealed that the ELM model outperformed the SVR and the GRNN models across a number of statistical measures. In quantitative terms, superiority of ELM over SVR and GRNN models was exhibited by ENS = 0.578, 0.378 and 0.144, r = 0.799, 0.761 and 0.468 and WI = 0.853, 0.802 and 0.689, respectively and the ELM model attained lower RMSE value by approximately 21.3% (relative to SVR) and by approximately 44.7% (relative to GRNN). Based on the findings of this study, several recommendations were suggested for further exploration of the ELM model in hydrological forecasting problems.

  2. Riparian Systems and Forest Management—Changes in Harvesting Techniques and their Effects on Decomposed Granitic Soils

    Treesearch

    John W. Bramhall

    1989-01-01

    In the 1950s, timber on steep granitic terrain in Trinity County, California was harvested by using the logging techniques of the time. After Trinity Dam was built in the 1960s, it became evident these techniques were not suited to quality riparian habitat and healthy anadromous fisheries. Since adoption of the Z'berg-Nejedly Forest Practice Act in 1973, efforts...

  3. Map Showing Geology and Hydrostratigraphy of the Edwards Aquifer Catchment Area, Northern Bexar County, South-Central Texas

    USGS Publications Warehouse

    Clark, Amy R.; Blome, Charles D.; Faith, Jason R.

    2009-01-01

    Rock units forming the Edwards and Trinity aquifers in northern Bexar County, Texas, are exposed within all or parts of seven 7.5-minute quadrangles: Bulverde, Camp Bullis, Castle Hills, Helotes, Jack Mountain, San Geronimo, and Van Raub. The Edwards aquifer is the most prolific ground-water source in Bexar County, whereas the Trinity aquifer supplies water for residential, commercial, and industrial uses for areas north of the San Antonio. The geologic map of northern Bexar County shows the distribution of informal hydrostratigraphic members of the Edwards Group and the underlying upper member of the Glen Rose Limestone. Exposures of the Glen Rose Limestone, which forms the Trinity aquifer alone, cover approximately 467 km2 in the county. This study also describes and names five informal hydrostratigraphic members that constitute the upper member of the Glen Rose Limestone; these include, in descending order, the Caverness, Camp Bullis, Upper evaporite, Fossiliferous, and Lower evaporite members. This study improves our understanding of the hydrogeologic connection between the two aquifers as it describes the geology that controls the infiltration of surface water and subsurface flow of ground water from the catchment area (outcropping Trinity aquifer rocks) to the Edwards water-bearing exposures.

  4. Factors Regulating Early Life History Dispersal of Atlantic Cod (Gadus morhua) from Coastal Newfoundland

    PubMed Central

    Stanley, Ryan R. E.; deYoung, Brad; Snelgrove, Paul V. R.; Gregory, Robert S.

    2013-01-01

    To understand coastal dispersal dynamics of Atlantic cod (Gadus morhua), we examined spatiotemporal egg and larval abundance patterns in coastal Newfoundland. In recent decades, Smith Sound, Trinity Bay has supported the largest known overwintering spawning aggregation of Atlantic cod in the region. We estimated spawning and dispersal characteristics for the Smith Sound-Trinity Bay system by fitting ichthyoplankton abundance data to environmentally-driven, simplified box models. Results show protracted spawning, with sharply increased egg production in early July, and limited dispersal from the Sound. The model for the entire spawning season indicates egg export from Smith Sound is 13%•day−1 with a net mortality of 27%•day–1. Eggs and larvae are consistently found in western Trinity Bay with little advection from the system. These patterns mirror particle tracking models that suggest residence times of 10–20 days, and circulation models indicating local gyres in Trinity Bay that act in concert with upwelling dynamics to retain eggs and larvae. Our results are among the first quantitative dispersal estimates from Smith Sound, linking this spawning stock to the adjacent coastal waters. These results illustrate the biophysical interplay regulating dispersal and connectivity originating from inshore spawning of coastal northwest Atlantic. PMID:24058707

  5. Lead isotopic composition of trinitite melt glass: evidence for the presence of Canadian industrial lead in the first atomic weapon test.

    PubMed

    Bellucci, Jeremy J; Simonetti, Antonio; Wallace, Christine; Koeman, Elizabeth C; Burns, Peter C

    2013-08-06

    The Pb isotopic compositions for 51 spots of melt glass in 11 samples of trinitite have been determined by laser ablation multicollector inductively coupled plasma mass spectrometry (LA-MC-ICP-MS). Trinitite glass yields a large range of Pb isotopic compositions (i.e., (206)Pb/(204)Pb = 17.08-19.04), which reflect mixing between industrial Pb from materials used in the Trinity test and natural geologic components. Areas within trinitite melt glass containing high concentrations of both Cu and Pb, which are derived from the bomb and blast site-related components, were used for delineating the Pb isotopic composition corresponding to the anthropogenic Pb component. Comparison between the isotopic composition estimated here for the industrial Pb used in the Trinity test and those from known Pb deposits worldwide indicates close agreement with ore from the Buchans mine (Newfoundland, Canada). The Buchans mine was active during the time of the Trinity test and was operated by the American Smelting and Refining Company, which could have provided the Pb used in the test. The industrial Pb used in the Trinity test materials is not documented in the literature (or declassified) but could have been present in bricks, solder, pigs, or some other anthropogenic component related to the experiment.

  6. Topographic view of the North Fork Butter Creek Bridge (located ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Topographic view of the North Fork Butter Creek Bridge (located center of frame), view looking west - North Fork Butter Creek Bridge, Spanning North Fork Butter Creek Bridge at Milepost 76.63 on Heppner Highway (Oregon Route 74), Pilot Rock, Umatilla County, OR

  7. RFWD3-Dependent Ubiquitination of RPA Regulates Repair at Stalled Replication Forks.

    PubMed

    Elia, Andrew E H; Wang, David C; Willis, Nicholas A; Boardman, Alexander P; Hajdu, Ildiko; Adeyemi, Richard O; Lowry, Elizabeth; Gygi, Steven P; Scully, Ralph; Elledge, Stephen J

    2015-10-15

    We have used quantitative proteomics to profile ubiquitination in the DNA damage response (DDR). We demonstrate that RPA, which functions as a protein scaffold in the replication stress response, is multiply ubiquitinated upon replication fork stalling. Ubiquitination of RPA occurs on chromatin, involves sites outside its DNA binding channel, does not cause proteasomal degradation, and increases under conditions of fork collapse, suggesting a role in repair at stalled forks. We demonstrate that the E3 ligase RFWD3 mediates RPA ubiquitination. RFWD3 is necessary for replication fork restart, normal repair kinetics during replication stress, and homologous recombination (HR) at stalled replication forks. Mutational analysis suggests that multisite ubiquitination of the entire RPA complex is responsible for repair at stalled forks. Multisite protein group sumoylation is known to promote HR in yeast. Our findings reveal a similar requirement for multisite protein group ubiquitination during HR at stalled forks in mammalian cells. Copyright © 2015 Elsevier Inc. All rights reserved.

  8. Feasibility and safety of modified inverted T-shaped method using linear stapler with movable cartridge fork for esophagojejunostomy following laparoscopic total gastrectomy.

    PubMed

    Ohuchida, Kenoki; Nagai, Eishi; Moriyama, Taiki; Shindo, Koji; Manabe, Tatsuya; Ohtsuka, Takao; Shimizu, Shuji; Nakamura, Masafumi

    2017-01-01

    We previously reported the use of an inverted T-shaped method to obtain a suitable view for hand sewing to close the common entry hole when the linear stapler was fired for esophagojejunostomy after laparoscopic total gastrectomy (LTG). This conventional method involved insertion of the fixed cartridge fork to the Roux limb and the fine movable anvil fork to the esophagus to avoid perforation of the jejunum. However, insertion of the movable anvil fork to the esophagus during this procedure often requires us to strongly push down the main body of the stapler with the fixed cartridge fork to bring the direction of the anvil fork in line with the direction of the long axis of the esophagus while controlling the opening of the movable anvil fork. We therefore modified this complicated inverted T-shaped method using a linear stapler with a movable cartridge fork. This modified method involved insertion of the movable cartridge fork into the Roux limb followed by natural, easy insertion of the fixed anvil fork into the esophagus without controlling the opening of the movable cartridge fork. We performed LTG in a total of 155 consecutive patients with gastric cancer from November 2007 to December 2015 in Kyushu University Hospital. After LTG, we performed the conventional inverted T-shaped method using a linear stapler with a fixed cartridge fork in 61 patients from November 2007 to July 2011 (fixed cartridge group). From August 2011, we used a linear stapler with a movable cartridge fork and performed the modified inverted T-shaped method in 94 patients (movable cartridge group). We herein compare the short-term outcomes in 94 cases of LTG using the modified method (movable cartridge fork) with those in 61 cases using the conventional method (fixed cartridge fork). We found no significant differences in the perioperative or postoperative events between the movable and fixed cartridge groups. One case of anastomotic leakage occurred in the fixed cartridge group, but no anastomotic leakage occurred in the movable cartridge group. Although there were no remarkable differences in the short-term outcomes between the movable and fixed cartridge groups, we believe that the modified inverted T-shaped method is technically more feasible and reliable than the conventional method and will contribute to the improved safety of LTG.

  9. Feasibility and safety of modified inverted T-shaped method using linear stapler with movable cartridge fork for esophagojejunostomy following laparoscopic total gastrectomy

    PubMed Central

    Ohuchida, Kenoki; Moriyama, Taiki; Shindo, Koji; Manabe, Tatsuya; Ohtsuka, Takao; Shimizu, Shuji; Nakamura, Masafumi

    2017-01-01

    Background We previously reported the use of an inverted T-shaped method to obtain a suitable view for hand sewing to close the common entry hole when the linear stapler was fired for esophagojejunostomy after laparoscopic total gastrectomy (LTG). This conventional method involved insertion of the fixed cartridge fork to the Roux limb and the fine movable anvil fork to the esophagus to avoid perforation of the jejunum. However, insertion of the movable anvil fork to the esophagus during this procedure often requires us to strongly push down the main body of the stapler with the fixed cartridge fork to bring the direction of the anvil fork in line with the direction of the long axis of the esophagus while controlling the opening of the movable anvil fork. We therefore modified this complicated inverted T-shaped method using a linear stapler with a movable cartridge fork. This modified method involved insertion of the movable cartridge fork into the Roux limb followed by natural, easy insertion of the fixed anvil fork into the esophagus without controlling the opening of the movable cartridge fork. Methods We performed LTG in a total of 155 consecutive patients with gastric cancer from November 2007 to December 2015 in Kyushu University Hospital. After LTG, we performed the conventional inverted T-shaped method using a linear stapler with a fixed cartridge fork in 61 patients from November 2007 to July 2011 (fixed cartridge group). From August 2011, we used a linear stapler with a movable cartridge fork and performed the modified inverted T-shaped method in 94 patients (movable cartridge group). We herein compare the short-term outcomes in 94 cases of LTG using the modified method (movable cartridge fork) with those in 61 cases using the conventional method (fixed cartridge fork). Results We found no significant differences in the perioperative or postoperative events between the movable and fixed cartridge groups. One case of anastomotic leakage occurred in the fixed cartridge group, but no anastomotic leakage occurred in the movable cartridge group. Conclusions Although there were no remarkable differences in the short-term outcomes between the movable and fixed cartridge groups, we believe that the modified inverted T-shaped method is technically more feasible and reliable than the conventional method and will contribute to the improved safety of LTG. PMID:28616606

  10. [History of the tuning fork. I: Invention of the tuning fork, its course in music and natural sciences. Pictures from the history of otorhinolaryngology, presented by instruments from the collection of the Ingolstadt German Medical History Museum].

    PubMed

    Feldmann, H

    1997-02-01

    G. Cardano, physician, mathematician, and astrologer in Pavia, Italy, in 1550 described how sound may be perceived through the skull. A few years later H. Capivacci, also a physician in Padua, realized that this phenomenon might be used as a diagnostic tool for differentiating between hearing disorders located either in the middle ear or in the acoustic nerve. The German physician G. C. Schelhammer in 1684 was the first to use a common cutlery fork in further developing the experiments initiated by Cardano and Capivacci. For a long time to come, however, there was no demand for this in practical otology. The tuning fork was invented in 1711 by John Shore, trumpeter and lutenist to H. Purcell and G.F. Händel in London. A picture of Händel's own tuning fork, probably the oldest tuning fork in existence, is presented here for the first time. There are a number of anecdotes connected with the inventor of the tuning fork, using plays on words involving the name Shore, and mixing up pitch-pipe and pitchfork. Some of these are related here. The tuning fork as a musical instrument soon became a success throughout Europe. The German physicist E. F. F. Chladni in Wittenberg around 1800 was the first to systematically investigate the mode of vibration of the tuning fork with its nodal points. Besides this, he and others tried to construct a complete musical instrument based on sets of tuning forks, which, however, were not widely accepted. J. H. Scheibler in Germany in 1834 presented a set of 54 tuning forks covering the range from 220 Hz to 440 Hz, at intervals of 4 Hz. J. Lissajous in Paris constructed a very elaborate tuning fork with a resonance box, which was intended to represent the international standard of the musical note A with 435 vibrations per second, but this remained controversial. K. R. Koenig, a German physicist living in Paris, invented a tuning fork which was kept in continuous vibration by a clockwork. H. Helmholtz, physiologist in Heidelberg, in 1863 used sets of electromagnetically powered tuning forks for his famous experiments on the sensations of tone. Until the invention of the electronic valve, tuning forks remained indispensible instruments for producing defined sinusoidal vibrations. The history of this development is presented in detail. The diagnostic use of the tuning fork in otology will be described in a separate article.

  11. ELM control with RMP: plasma response models and the role of edge peeling response

    NASA Astrophysics Data System (ADS)

    Liu, Yueqiang; Ham, C. J.; Kirk, A.; Li, Li; Loarte, A.; Ryan, D. A.; Sun, Youwen; Suttrop, W.; Yang, Xu; Zhou, Lina

    2016-11-01

    Resonant magnetic perturbations (RMP) have extensively been demonstrated as a plausible technique for mitigating or suppressing large edge localized modes (ELMs). Associated with this is a substantial amount of theory and modelling efforts during recent years. Various models describing the plasma response to the RMP fields have been proposed in the literature, and are briefly reviewed in this work. Despite their simplicity, linear response models can provide alternative criteria, than the vacuum field based criteria, for guiding the choice of the coil configurations to achieve the best control of ELMs. The role of the edge peeling response to the RMP fields is illustrated as a key indicator for the ELM mitigation in low collisionality plasmas, in various tokamak devices.

  12. A classification scheme for edge-localized modes based on their probability distributions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Shabbir, A., E-mail: aqsa.shabbir@ugent.be; Max Planck Institute for Plasma Physics, D-85748 Garching; Hornung, G.

    We present here an automated classification scheme which is particularly well suited to scenarios where the parameters have significant uncertainties or are stochastic quantities. To this end, the parameters are modeled with probability distributions in a metric space and classification is conducted using the notion of nearest neighbors. The presented framework is then applied to the classification of type I and type III edge-localized modes (ELMs) from a set of carbon-wall plasmas at JET. This provides a fast, standardized classification of ELM types which is expected to significantly reduce the effort of ELM experts in identifying ELM types. Further, themore » classification scheme is general and can be applied to various other plasma phenomena as well.« less

  13. The fork and the kinase: a DNA replication tale from a CHK1 perspective.

    PubMed

    González Besteiro, Marina A; Gottifredi, Vanesa

    2015-01-01

    Replication fork progression is being continuously hampered by exogenously introduced and naturally occurring DNA lesions and other physical obstacles. Checkpoint kinase 1 (Chk1) is activated at replication forks that encounter damaged DNA. Subsequently, Chk1 inhibits the initiation of new replication factories and stimulates the firing of dormant origins (those in the vicinity of stalled forks). Chk1 also avoids fork collapse into DSBs (double strand breaks) and promotes fork elongation. At the molecular level, the current model considers stalled forks as the site of Chk1 activation and the nucleoplasm as the location where Chk1 phosphorylates target proteins. This model certainly serves to explain how Chk1 modulates origin firing, but how Chk1 controls the fate of stalled forks is less clear. Interestingly, recent reports demonstrating that Chk1 phosphorylates chromatin-bound proteins and even holds kinase-independent functions might shed light on how Chk1 contributes to the elongation of damaged DNA. Indeed, such findings have unveiled a puzzling connection between Chk1 and DNA lesion bypass, which might be central to promoting fork elongation and checkpoint attenuation. In summary, Chk1 is a multifaceted and versatile signaling factor that acts at ongoing forks and replication origins to determine the extent and quality of the cellular response to replication stress. Copyright © 2014 Elsevier B.V. All rights reserved.

  14. 21 CFR 882.1525 - Tuning fork.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Tuning fork. 882.1525 Section 882.1525 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1525 Tuning fork. (a) Identification. A tuning fork...

  15. 21 CFR 882.1525 - Tuning fork.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Tuning fork. 882.1525 Section 882.1525 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1525 Tuning fork. (a) Identification. A tuning fork...

  16. 36 CFR 292.62 - Valid existing rights.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... RECREATION AREAS Smith River National Recreation Area § 292.62 Valid existing rights. (a) Definition. For the... “wild” segments of the Wild and Scenic Smith River, Middle Fork Smith River, North Fork Smith River, Siskiyou Fork Smith River, South Fork Smith River, and their designated tributaries, except Peridotite...

  17. Effect of nitrogen seeding on the energy losses and on the time scales of the electron temperature and density collapse of type-I ELMs in JET with the ITER-like wall

    NASA Astrophysics Data System (ADS)

    Frassinetti, L.; Dodt, D.; Beurskens, M. N. A.; Sirinelli, A.; Boom, J. E.; Eich, T.; Flanagan, J.; Giroud, C.; Jachmich, M. S.; Kempenaars, M.; Lomas, P.; Maddison, G.; Maggi, C.; Neu, R.; Nunes, I.; Perez von Thun, C.; Sieglin, B.; Stamp, M.; Contributors, JET-EFDA

    2015-02-01

    The baseline type-I ELMy H-mode scenario has been re-established in JET with the new tungsten MKII-HD divertor and beryllium on the main wall (hereafter called the ITER-like wall, JET-ILW). The first JET-ILW results show that the confinement is degraded by 20-30% in the baseline scenarios compared to the previous carbon wall JET (JET-C) plasmas. The degradation is mainly driven by the reduction in the pedestal temperature. Stored energies and pedestal temperature comparable to the JET-C have been obtained to date in JET-ILW baseline plasmas only in the high triangularity shape using N2 seeding. This work compares the energy losses during ELMs and the corresponding time scales of the temperature and density collapse in JET-ILW baseline plasmas with and without N2 seeding with similar JET-C baseline plasmas. ELMs in the JET-ILW differ from those with the carbon wall both in terms of time scales and energy losses. The ELM time scale, defined as the time to reach the minimum pedestal temperature soon after the ELM collapse, is ˜2 ms in the JET-ILW and lower than 1 ms in the JET-C. The energy losses are in the range ΔWELM/Wped ≈ 7-12% in the JET-ILW and ΔWELM/Wped ≈ 10-20% in JET-C, and fit relatively well with earlier multi-machine empirical scalings of ΔWELM/Wped with collisionality. The time scale of the ELM collapse seems to be related to the pedestal collisionality. Most of the non-seeded JET-ILW ELMs are followed by a further energy drop characterized by a slower time scale ˜8-10 ms (hereafter called slow transport events), that can lead to losses in the range ΔWslow/Wped ≈ 15-22%, slightly larger than the losses in JET-C. The N2 seeding in JET-ILW significantly affects the ELMs. The JET-ILW plasmas with N2 seeding are characterized by ELM energy losses and time scales similar to the JET-C and by the absence of the slow transport events.

  18. Modelling of nitrogen seeding experiments in the ASDEX Upgrade tokamak

    NASA Astrophysics Data System (ADS)

    Casali, L.; Fable, E.; Dux, R.; Ryter, F.; ASDEX Upgrade Team

    2018-03-01

    Experiments using nitrogen were conducted in H-mode plasmas at ASDEX Upgrade that has a full-W wall. The edge region of H-mode plasmas is modulated by the edge-localized modes (ELMs) which lead to a loss of energy and particles from the confined plasma. In order to gain a better understanding of the complex physical mechanisms which govern the behaviour of radiation and impurities in the presence of ELMs, the evolution of impurities and radiation has been modelled in a time-dependent way. The simulations have been carried out with the ASTRA-STRAHL package featuring the self-consistent interplay between impurity transport, radiation, heat and particle transport of the background plasma, and the effects of ELMs. ELMs are modelled based on the two different assumptions of a diffusive and a convective transport, respectively. The experimental discharge behaviour was reproduced providing only transport coefficients, heat, and particle source. The results underlie the importance of non-coronal effects through the ELM-induced transport which lead to a strong enhancement of the nitrogen radiation. Taking these effects into account is crucial in order to not underestimate the radiation. The radiation properties of high-Z impurities such as tungsten are instead very weakly influenced by non-coronal effects due to its faster equilibration time. While the nitrogen density does not change significantly decreasing the ELM frequency, tungsten density and consequently the radiation increase strongly. The degree to which W is flushed out depends on whether the ELM transport is diffusive or convective. Simulations show that for the N seeded cases considered here, the diffusive model reproduces more accurately the experimental observations. The different behaviour of N and W can be explained in terms of profile peaking which increases with Z (neoclassical pinch). The strong increase in W radiation when the ELM frequency is decreased is not only due to the lack of a sufficiently strong flush out of this impurity but also to the fact that the long time between two crashes gives the impurities time to penetrate further into the plasma escaping the region where they can be flushed out. This is in agreement with the experimental observations and highlights the importance of maintaining high ELM frequencies for the stability and performance of the discharges.

  19. Impurity confinement and transport in high confinement regimes without edge localized modes on DIII-D [Impurity confinement and transport in high confinement regimes without ELMs on DIII-D

    DOE PAGES

    Grierson, Brian A.; Burrell, Keith H.; Nazikian, Raffi M.; ...

    2015-04-17

    Here, impurity transport in the DIII-D tokamak is investigated in stationary high confinement (H-mode) regimes without edge localized modes (ELMs). In plasmas maintained by resonant magnetic perturbation (RMP) ELM-suppression and QH-mode the confinement time of fluorine (Z=9) is equivalent to that in ELMing discharges with 40 Hz ELMs. For selected discharges with impurity injection the impurity particle confinement time compared to the energy confinement time is in the range of τ p/τ e ≈ 2 $-$ 3. In QH-mode operation the impurity confinement time is shown to be smaller for intense, coherent magnetic and density fluctuations of the edge harmonicmore » oscillation than weaker fluctuations. Transport coefficients are derived from the time evolution of the impurity density profile and compared to neoclassical and turbulent transport models NEO and TGLF. Neoclassical transport of fluorine is found to be small compared to the experimental values. In the ELMing and RMP ELM-suppressed plasma the impurity transport is affected by the presence of tearing modes. For radii larger than the mode radius the TGLF diffusion coefficient is smaller than the experimental value by a factor of 2-3, while the convective velocity is within error estimates. Low levels of diffusion are observed for radii smaller than the tearing mode radius. In the QH-mode plasma investigated, the TGLF diffusion coefficient higher inside of ρ = 0.4 and lower outside of 0.4 than the experiment, and the TGLF convective velocity is more negative by a factor of approximately 1.7.« less

  20. Is cardiovascular disease in patients with diabetes associated with serum levels of MMP-2, LOX, and the elastin degradation products ELM and ELM-2?

    PubMed

    Preil, Simone Andrea Rørdam; Thorsen, Anne-Sofie Faarvang; Christiansen, Anne Lindegaard; Poulsen, Mikael Kjær; Karsdal, Morten Asser; Leeming, Diana Julie; Rasmussen, Lars Melholt

    2017-11-01

    Diabetes mellitus type 2 (T2DM) is a significant risk factor for the development of cardiovascular diseases (CVDs). In a previous microarray study of internal mammary arteries from patients with and without T2DM, we observed several elastin-related genes with altered mRNA-expression in diabetic patients, namely matrix metalloproteinase 2 (MMP-2), lysyl oxidase (LOX) and elastin itself. In this study we investigate whether the serum concentrations of elastin-related proteins correlate to signs of CVD in patients with T2DM. Blood samples from 302 type 2 diabetic patients were analysed for MMP-2, LOX, and the elastin degradation products ELM and ELM2. The results were investigated for correlations to signs of CVD in different vascular territories, as determined by myocardial perfusion scintigraphy, carotid artery thickness and ankle-brachial blood pressure index. T2DM patients with peripheral arterial disease (low ankle-brachial index) (PAD) display higher levels of MMP-2 and ELM compared to patients without PAD. However, none of the proteins or degradation products correlated with myocardial ischemia or a combined measure of CVD-signs, including myocardial ischemia, increased carotid thickness and decreased ankle-brachial blood pressure. Our results suggest that the diabetic environment affects the circulating amounts of MMP-2 and ELM in patients with PAD. However, the same connection could not be seen in diabetic patients with CVD broadly identified in three vascular territories. LOX and ELM-2 did not correlate to any type of CVD. Overall, serum levels of elastin-related molecules are only remotely related to CVD in type 2 diabetes.

Some links on this page may take you to non-federal websites. Their policies may differ from this site.
Top