Biofiltration of asphalt emissions: Full-scale operation treating off-gases from polymer-modified asphalt production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, L.L.; Gostomski, P.A.; Apel, W.A.

1999-09-30

In response to complaints from nearby residents, a biofilter was designed, installed, and tested for treating odors in one of three odorous emission streams from an asphalt plant producing polymer-modified asphalt. Hydrogen sulfide (H{sub 2}S) was determined to be the most prevalent gaseous reduced sulfur compound and was detected in the emission stream only when polymer material was being added to raw asphalt. Emission stream H{sub 2}S concentrations were quite variable, ranging from 16 to approximately 30,000 ppm (v/v) and considered the likely compound contributing most to the plant's odor complaints. The biofilter was effective in controlling odor from themore » production process and removed an overall average of 65% of the H{sub 2}S during polymer addition, and for H{sub 2}S concentrations less than 400 ppmv, removal averaged 98%. These removal efficiencies reflect data from the biofilter operating at 2.5-minute empty bed residence time in 1996 and a 6.1-minute empty bed residence time in 1997. The biofilter's bed became increasingly acidified during the plant's 1997 operating season producing a pH gradient through the bed ranging from a high of 6.6 to a low of 3.1. The bed medium moisture content remained constant at about 60% (wet weight basis), but changes were observed in the water potential: no correlation to performance was determined. Changes in the microbial community reflected the bed acidification trend, with acidophiles becoming generally more numerous in the bed's deeper portions and in the mid to late season when the bed was most acidified. Bed acidification did not impact the biofilter's H{sub 2}S removal efficiency.« less

Empty threat: Hospitals could see more vacancies as demand for outpatient care grows and financial pressure builds to curb inpatient admissions.

PubMed

Evans, Melanie

2012-03-26

Markets with too many hospital beds could see trouble as providers seek to control spending and avoid expensive hospitalizations. "You'll need a lot fewer hospitals and hospital beds" because providers will do more to keep patients healthy enough not to need them, says Frank Trembulak, of Geisinger Health System.

Biological activation of carbon filters.

PubMed

Seredyńska-Sobecka, Bozena; Tomaszewska, Maria; Janus, Magdalena; Morawski, Antoni W

2006-01-01

To prepare biological activated carbon (BAC), raw surface water was circulated through granular activated carbon (GAC) beds. Biological activity of carbon filters was initiated after about 6 months of filter operation and was confirmed by two methods: measurement of the amount of biomass attached to the carbon and by the fluorescein diacetate (FDA) test. The effect of carbon pre-washing on WG-12 carbon properties was also studied. For this purpose, the nitrogen adsorption isotherms at 77K and Fourier transform-infrared (FT-IR) spectra analyses were performed. Moreover, iodine number, decolorizing power and adsorption properties of carbon in relation to phenol were studied. Analysis of the results revealed that after WG-12 carbon pre-washing its BET surface increased a little, the pH value of the carbon water extract decreased from 11.0 to 9.4, decolorizing power remained at the same level, and the iodine number and phenol adsorption rate increased. In preliminary studies of the ozonation-biofiltration process, a model phenol solution with concentration of approximately 10mg/l was applied. During the ozonation process a dose of 1.64 mg O(3)/mg TOC (total organic carbon) was employed and the contact time was 5 min. Four empty bed contact times (EBCTs) in the range of 2.4-24.0 min were used in the biofiltration experiment. The effectiveness of purification was measured by the following parameters: chemical oxygen demand (COD(Mn)), TOC, phenol concentration and UV(254)-absorbance. The parameters were found to decrease with EBCT.

Comparative modeling of biological nutrient removal from landfill leachate using a circulating fluidized bed bioreactor (CFBBR).

PubMed

Eldyasti, Ahmed; Andalib, Mehran; Hafez, Hisham; Nakhla, George; Zhu, Jesse

2011-03-15

Steady state operational data from a pilot scale circulating fluidized bed bioreactor (CFBBR) during biological treatment of landfill leachate, at empty bed contact times (EBCTs) of 0.49, and 0.41 d and volumetric nutrients loading rates of 2.2-2.6 kg COD/(m(3)d), 0.7-0.8 kg N/(m(3)d), and 0.014-0.016 kg P/(m(3)d), was used to calibrate and compare developed process models in BioWin(®) and AQUIFAS(®). BioWin(®) and AQUIFAS(®) were both capable of predicting most of the performance parameters such as effluent TKN, NH(4)-N, NO(3)-N, TP, PO(4)-P, TSS, and VSS with an average percentage error (APE) of 0-20%. BioWin(®) underpredicted the effluent BOD and SBOD values for various runs by 80% while AQUIFAS(®) predicted effluent BOD and SBOD with an APE of 50%. Although both calibrated models, confirmed the advantages of the CFBBR technology in treating the leachate of high volumetric loading and low biomass yields due to the long solid retention time (SRT), both BioWin(®) and AQUIFAS(®) predicted the total biomass and SRT of CFBBR based on active biomass only, whereas in the CFBBR runs both active as well as inactive biomass accumulated. Copyright © 2011 Elsevier B.V. All rights reserved.

Remediation of Organic and Inorganic Arsenic Contaminated Groundwater using a Nonocrystalline TiO2 Based Adsorbent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jing, C.; Meng, X; Calvache, E

2009-01-01

A nanocrystalline TiO2-based adsorbent was evaluated for the simultaneous removal of As(V), As(III), monomethylarsonic acid (MMA), and dimethylarsinic acid (DMA) in contaminated groundwater. Batch experimental results show that As adsorption followed pseudo-second order rate kinetics. The competitive adsorption was described with the charge distribution multi-site surface complexation model (CD-MUSIC). The groundwater containing an average of 329 ?g L-1 As(III), 246 ?g L-1 As(V), 151 ?g L-1 MMA, and 202 ?g L-1 DMA was continuously passed through a TiO2 filter at an empty bed contact time of 6 min for 4 months. Approximately 11 000, 14 000, and 9900 bed volumesmore » of water had been treated before the As(III), As(V), and MMA concentration in the effluent increased to 10 ?g L-1. However, very little DMA was removed. The EXAFS results demonstrate the existence of a bidentate binuclear As(V) surface complex on spent adsorbent, indicating the oxidation of adsorbed As(III). A nanocrystalline TiO2-based adsorbent could be used for the simultaneous removal of As(V), As(III), MMA, and DMA in contaminated groundwater.« less

Column study of chromium(VI) adsorption from electroplating industry by coconut coir pith.

PubMed

Suksabye, Parinda; Thiravetyan, Paitip; Nakbanpote, Woranan

2008-12-15

The removal of Cr(VI) from electroplating wastewater by coir pith was investigated in a fixed-bed column. The experiments were conducted to study the effect of important parameters such as bed depth (40-60cm) and flow rate (10-30ml min(-1)). At 0.05 C(t)/C(0), the breakthrough volume increased as flow rate decreased or a bed depth increased due to an increase in empty bed contact time (EBCT). The bed depth service time model (BDST) fit well with the experimental data in the initial region of the breakthrough curve, while the simulation of the whole curve using non-linear regression analysis was effective using the Thomas model. The adsorption capacity estimated from the BDST model was reduced with increasing flow rate, which was 16.40mg cm(-3) or 137.91mg Cr(VI)g(-1) coir pith for the flow rates of 10ml min(-1) and 14.05mg cm(-3) or 118.20mg Cr(VI)g(-1) coir pith for the flow rates of 30ml min(-1). At the highest bed depth (60cm) and the lowest flow rate (10mlmin(-1)), the maximum adsorption reached 201.47mg Cr(VI)g(-1) adsorbent according to the Thomas model. The column was regenerated by eluting chromium using 2M HNO(3) after adsorption studies. The desorption of Cr(III) in each of three cycles was about 67-70%. The desorption of Cr(III) in each cycle did not reach 100% due to the fact that Cr(V) was present through the reduction of Cr(VI), and was still in coir pith, possibly bound to glucose in the cellulose part of coir pith. Therefore, the Cr(V) complex cannot be desorbed in solution. The evidence of Cr(V) signal was observed in coir pith, alpha-cellulose and holocellulose extracted from coir pith using electron spin resonance (ESR).

Removal of arsenic from aqueous solutions using waste iron columns inoculated with iron bacteria.

PubMed

Azhdarpoor, Abooalfazl; Nikmanesh, Roya; Samaei, Mohammad Reza

2015-01-01

Arsenic contamination of water resources is one of the serious risks threatening natural ecosystems and human health. This study investigates arsenic removal using a waste iron column with and without iron bacteria in continuous and batch phases. In batch experiments, the effects of pH, contact time, initial concentration of arsenic and adsorbent dose were investigated. Results indicated that the highest arsenate removal efficiency occurred at pH 7 (96.76%). On increasing the amount of waste iron from 0.25 to 1 g, the removal rate changed from about 42.37%-96.70%. The results of continuous experiments on the column containing waste iron showed that as the empty bed contact time increased from 5 to 60 min, the secondary arsenate concentration changed from 23 to 6 µg/l. In experiments involving a waste iron column with iron bacteria, an increase in residence time from 5 to 60 min decreased the secondary arsenate concentration from 14.97 to 4.86 µg/l. The results of this study showed that waste iron containing iron bacteria is a good adsorbent for removal of arsenic from contaminated water.

Effect of guar gum on hunger and satiety after meals of differing fat content: relationship with gastric emptying.

PubMed

French, S J; Read, N W

1994-01-01

To determine whether the satiating effects of fiber are due to delaying gastric emptying or slowing absorption of meals, 3% guar gum was added to high- and low-fat soups and gastric emptying rate, hunger, and satiety were measured in eight male volunteers. Guar gum delayed the emptying of the low-fat soup but the small delays in the return of hunger and decline of fullness were significantly correlated with the gastric emptying, suggesting mediation by gastric mechanoreceptors. The high-fat soup also emptied more slowly but this had no effect on the return of hunger or the decline in fullness. The delays in the return of hunger and decline of fullness were far greater when guar gum was added to the fatty soup; these delays were not correlated with the small additional delay in gastric emptying. This is more compatible with slowed absorption and prolonged contact of nutrients with intestinal chemoreceptors.

Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Connolly, J.R.; Keil, K.; Mansker, W.L.

1984-10-01

This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworkedmore » zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain.« less

Biofiltration of Asphalt Emissions: Full-scale Operation Treating Off-gases from Polymer-modified Asphalt Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, Lawrence Leslie; Apel, William Arnold; Gostomski, P. A.

2004-04-01

In response to complaints from nearby residents, a biofilter was designed, installed, and tested for treating odors in one of three odorous emission streams from an asphalt plant producing polymer-modified asphalt. Hydrogen sulfide (H2S) was determined to be the most prevalent gaseous reduced sulfur compound and was detected in the emission stream only when polymer material was being added to raw asphalt. Emission stream H2S concentrations we requite variable, ranging from 16 to approximately 30,000 ppm (v/v) and considered the likely compound contributing most to the plant's odor complaints. The biofilter was effective in controlling odor from the production processmore » and removed an overall average of 65% of the H2S during polymer addition, and for H2S concentrations less than 400 ppmv, re m oval averaged 98%. These removal efficiencies reflect data from the biofilter operating at 2.5-minute empty bed residence time in 1996 and a 6.1-minute empty bed residence time in 1997. The biofilter's bed became increasingly acidified during the plant's 1997 operating season producing a pH gradient through the bed ranging from a high of 6.6 to a low of 3.1. The bed medium moisture content remained constant at about 60% (wet weight basis), but changes were observed in the water potential: no correlation to performance was determined. Changes in the microbial community reflected the bed acidification trend, with acidophiles becoming gene rally more numerous in the bed's deeper portions and in the mid to late season when the bed was most acidified. Bed acidification did not impact the biofilter's H2S removal efficiency. Nearby residents we resurveyed and roughly half of the respondents indicated that the odor conditions had improved, one-third felt odor conditions were unchanged and the remaining 15% felt odor conditions were worse despite the fact that only one of three of the plant's odorous emission streams were treated by the biofilter. Plans are to implement biofiltration for odor control at all of the facility's emission points.« less

Empty Beds: Indian Student Health at Sherman Institute, 1902-1922.

ERIC Educational Resources Information Center

Keller, Jean A.

As one of the last nonreservation boarding schools built for American Indian students in the United States, Sherman Institute (Riverside, California) benefited from lessons learned about student health from earlier boarding schools. Excessive student morbidity and mortality at early boarding schools had resulted in a lasting perception of these…

Hydrogen sulfide removal from air by Acidithiobacillus thiooxidans in a trickle bed reactor.

PubMed

Ramirez, M; Gómez, J M; Cantero, D; Páca, J; Halecký, M; Kozliak, E I; Sobotka, M

2009-09-01

A strain of Acidithiobacillus thiooxidans immobilized in polyurethane foam was utilized for H(2)S removal in a bench-scale trickle-bed reactor, testing the limits of acidity and SO(4) (2-) accumulation. The use of this acidophilic strain resulted in remarkable stability in the performance of the system. The reactor maintained a >98-99 % H(2)S removal efficiency for c of up to 66 ppmv and empty bed residence time 98 % H(2)S was achieved under steady-state conditions, over the pH range of 0.44-7.30. Despite the accumulation of acidity and SO(4) (2-) (up to 97 g/L), the system operated without inhibition.

Evaluation of mixed valent iron oxides as reactive adsorbents for arsenic removal.

PubMed

Mishra, Dhananjay; Farrell, James

2005-12-15

The objective of this research was to determine if Fe(II)-bearing iron oxides generate ferric hydroxides at sufficient rates for removing low levels of arsenic in packed-bed reactors, while at the same time avoiding excessive oxide production that contributes to bed clogging in oxygenated waters. Column experiments were performed to determine the effectiveness of three media for arsenic removal over a range in empty bed contact times, influent arsenic concentrations, dissolved oxygen (DO) levels, and solution pH values. Corrosion rates of the media as a function of the water composition were determined using batch and electrochemical methods. Rates of arsenic removal were first order in the As(V) concentration and were greater for media with higher corrosion rates. As(V) removal increased with increasing DO levels primarily due to faster oxidation of the Fe2+ released by media corrosion. To obtain measurable amounts of arsenic removal in 15 mM NaCl electrolyte solutions containing 50 microg/L As(V), the rate of Fe2+ released by the media needed to be at least 15 times greater than the As(V) feed rate into the column. In waters containing 30 mg/L of silica and 50 microg/L of As(V), measurable amounts of arsenic removal were obtained only for Fe2+ release rates that were at least 200 times greater than the As(V) feed rate. Although all columns showed losses in hydraulic conductivity overthe course of 90 days of operation, the conductivity values remained high, and the losses could be reversed by backwashing the media. The reaction products produced by the media in domestic tap water had average As-to-Fe ratios that were approximately 25% higher than those for a commercially available adsorbent.

Exclusion processes: Short-range correlations induced by adhesion and contact interactions

NASA Astrophysics Data System (ADS)

Ascolani, Gianluca; Badoual, Mathilde; Deroulers, Christophe

2013-01-01

We analyze the out-of-equilibrium behavior of exclusion processes where agents interact with their nearest neighbors, and we study the short-range correlations which develop because of the exclusion and other contact interactions. The form of interactions we focus on, including adhesion and contact-preserving interactions, is especially relevant for migration processes of living cells. We show the local agent density and nearest-neighbor two-point correlations resulting from simulations on two-dimensional lattices in the transient regime where agents invade an initially empty space from a source and in the stationary regime between a source and a sink. We compare the results of simulations with the corresponding quantities derived from the master equation of the exclusion processes, and in both cases, we show that, during the invasion of space by agents, a wave of correlations travels with velocity v(t)˜t-1/2. The relative placement of this wave to the agent density front and the time dependence of its height may be used to discriminate between different forms of contact interactions or to quantitatively estimate the intensity of interactions. We discuss, in the stationary density profile between a full and an empty reservoir of agents, the presence of a discontinuity close to the empty reservoir. Then we develop a method for deriving approximate hydrodynamic limits of the processes. From the resulting systems of partial differential equations, we recover the self-similar behavior of the agent density and correlations during space invasion.

Bed Bugs FAQs

MedlinePlus

... Consultations, and General Public. Contact Us Parasites Home Bed Bugs FAQs Recommend on Facebook Tweet Share Compartir On ... are bed bugs treated and prevented? What are bed bugs? Bed bugs ( Cimex lectularius ) are small, flat, parasitic ...

The choice behaviour of pigs in a Y maze: effects of deprivation of feed, social contact and bedding.

PubMed

Hemsworth, Paul H; Smith, Kenneth; Karlen, Marcus G; Arnold, Naomi A; Moeller, Steven J; Barnett, John L

2011-06-01

We examined effects of deprivation of feed, social contact and bedding on the choice behaviour in Y maze tests. Eighty pigs were used to study two main effects: feed (estimated voluntary feed intake (VFI) vs. 70% VFI) and bedding (presence vs. absence), experiment 1; social contact (full vs. restricted) and bedding (presence vs. absence), experiment 2; and feed (as in experiment 1) and social contact (as in experiment 2), experiment 3. Overall pigs consistently chose feed and social contact over bedding. While social contact was more preferred than feed in experiment 3, there was substantial variation between pigs in their choice behaviour. The overall choice behaviour in experiment 3 contradicts previous research, but differences such as the preference methodology as well as the level of deprivation, level of reward and cost involved in accessing reward, may be responsible. Average daily weight gain (ADG) was affected in experiment 3: both feed and social restriction reduced ADG. While the feed effect is expected, one interpretation of the social effect is that social deprivation, through stress, may have reduced ADG. These results provide limited support for the notion that deprivation of a highly preferred resource may disrupt biological function. Copyright © 2011 Elsevier B.V. All rights reserved.

Caring holistically within new managerialism.

PubMed

Wong, Woon Hau

2004-03-01

This article explains the attempts of nurses to practice humanistic, holistic care in line with their professionalizing strategy. Ideally, the intention of nurses is to broaden their concerns beyond the physiological needs of patients, thereby circumventing biomedical control over their work. However, the author argues that resource constraints, and the coalescing of biomedical and managerial definitions of patients, suggest that holistic notions of care are subjected to a new form of calculus and normalizing technology. Critically, nurses are more preoccupied with the day-to-day struggle to free up resources for healthcare, in particular bed spaces, and to pre-empt the problem of bed blocking. Such work suggests that the "emptying of beds" is not just a symbol of accomplishment for nursing work. From the governmentality theory of Foucault, the administration of "beds" has become part of the managerial power/knowledge discourse and an instrument for making nurses toe the financial bottom-line.

24. VIEW SHOWING WASTE GATES ON GRAND CANAL AT JUNCTION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. VIEW SHOWING WASTE GATES ON GRAND CANAL AT JUNCTION WITH OLD CROSSCUT NE/4, Sec. 7, TIN, R4E; LOOKING WEST. OLD CROSSCUT CANAL ENTERS FROM RIGHT. WASTE GATE ON LEFT EMPTIES INTO SALT RIVER BED Photographer: Kevin Kreisel-Coons, May 1990 - Grand Canal, North side of Salt River, Tempe, Maricopa County, AZ

Evaluation of pharmaceuticals removal by sewage sludge-derived adsorbents with rapid small-scale column tests

NASA Astrophysics Data System (ADS)

Zhang, P.; Ding, R.; Wallace, R.; Bandosz, T.

2015-12-01

New composite adsorbents were developed by pyrolyzing sewage sludge and fish waste (75:25 or 90:10 dry mass ratio) at 650 oC and 950 oC. Batch adsorption experiments demonstrated that the composite adsorbents were able to adsorb a wide range of organic contaminants (volatile organic compounds, pharmaceuticals and endocrine disrupting compounds (EDCs), and nitrosamine disinfection byproducts) with high capacities. Here we further examine the performance of the adsorbents for the simultaneous removal of 8 pharmaceuticals and EDCs with rapid small-scale column tests (RSSCT). Results show that the order of breakthrough in RSSCT is in general consistent with the affinity determined via batch tests. As expected, the maximum amount of adsorption for each compound obtained from RSSCT is identical to or less than that obtained from batch tests (with only one exception), due to adsorption kinetics. However, despite the very different input concentration (1 mg/L vs. 100 mg/L) and contact time (2 min empty bed contact time vs. 16 hour equilibrium time) used in RSSCT and batch tests, the maximum amount of pharmaceuticals and EDCs adsorbed under RSSCT is still about one half of that under equilibrium batch tests, validating the approach of using batch tests with much higher input concentrations to determine adsorption capacities. Results of a pilot-scale column test in a drinking water treatment plant for pharmaceuticals removal will also be presented.

Effect of ozone on biopolymers in biofiltration and ultrafiltration processes.

PubMed

Siembida-Lösch, Barbara; Anderson, William B; Wang, Yulang Michael; Bonsteel, Jane; Huck, Peter M

2015-03-01

The focus of this full-scale study was to determine the effect of ozone on biopolymer concentrations in biofiltration and ultrafiltration (UF) processes treating surface water from Lake Ontario. Ozonation was out of service for maintenance for 9 months, hence, it was possible to investigate ozone's action on biologically active carbon contactors (BACCs) and UF, in terms of biopolymer removal. Given the importance of biopolymers for fouling, this fraction was quantified using a chromatographic technique. Ozone pre-treatment was observed to positively impact the active biomass in biofilters. However, since an increase of the active biomass did not result in higher biopolymer removal, active biomass concentration cannot be a surrogate for biofiltration performance. It was evident that increasing empty bed contact time (EBCT) from 4 to 19 min only had a positive effect on biopolymer removal through BACCs when ozone was out of service. However, as a mass balance experiment showed, ozone-free operation resulted in higher deposition of biopolymers on a UF membrane and slight deterioration in its performance. Copyright © 2014 Elsevier Ltd. All rights reserved.

Removal of bromide and bromate from drinking water using granular activated carbon.

PubMed

Zhang, Yong-Qing; Wu, Qing-Ping; Zhang, Ju-Mei; Yang, Xiu-Hua

2015-03-01

Granular activated carbon (GAC) was used to remove bromide (Br⁻) and bromate (BrO(3)(-)) from drinking water in both bench- and pilot-scale experiments. The present study aims to minimize BrO(3)(-) formation and eliminate BrO(3)(-) generated during the ozonation of drinking water, particularly in packaged drinking water. Results show that the Br⁻ and BrO(3)(-) levels in GAC-treated water decreased in both bench- and pilot-scale experiments. In the bench-scale experiments, when the empty bed contact time (EBCT) was 5 min, the highest reduction rates of Br(-) in the mineral and ultrapure water were found to be 74.9% and 91.2%, respectively, and those of BrO(3)(-) were 94.4% and 98.8%, respectively. The GAC capacity for Br⁻ and BrO(3)(-) removal increased with the increase in EBCT. Reduction efficiency was better in ultrapure water than in mineral water. In the pilot-scale experiments, the minimum reduction rates of Br⁻ and BrO(3)(-) were 38.5% and 73.2%, respectively.

Rapid small-scale column testing of granular activated carbon for organic micro-pollutant removal in treated domestic wastewater.

PubMed

Zietzschmann, F; Müller, J; Sperlich, A; Ruhl, A S; Meinel, F; Altmann, J; Jekel, M

2014-01-01

This study investigates the applicability of the rapid small-scale column test (RSSCT) concept for testing of granular activated carbon (GAC) for organic micro-pollutants (OMPs) removal from wastewater treatment plant (WWTP) effluent. The chosen experimental setup was checked using pure water, WWTP effluent, different GAC products, and variable hydrodynamic conditions with different flow velocities and differently sized GAC, as well as different empty bed contact times (EBCTs). The setup results in satisfying reproducibility and robustness. RSSCTs in combination with WWTP effluent are effective when comparing the OMP removal potentials of different GAC products and are a useful tool for the estimation of larger filters. Due to the potentially high competition between OMPs and bulk organics, breakthrough curves are likely to have unfavorable shapes when treating WWTP effluent. This effect can be counteracted by extending the EBCT. With respect to the strong competition observed in GAC treatment of WWTP effluent, the small organic acid and neutral substances are retained longer in the RSSCT filters and are likely to cause the majority of the observed adsorption competition with OMPs.

Method and apparatus for improving heat transfer in a fluidized bed

DOEpatents

Lessor, Delbert L.; Robertus, Robert J.

1990-01-01

An apparatus contains a fluidized bed that includes particles of different triboelectrical types, each particle type acquiring an opposite polarity upon contact. The contact may occur between particles of the two types or between particles of etiher type and structure or fluid present in the apparatus. A fluidizing gas flow is passed through the particles to produce the fluidized bed. Immersed within the bed are electrodes. An alternating EMF source connected to the electrodes applies an alternating electric field across the fluidized bed to cause particles of the first type to move relative to particles of the second type and relative to the gas flow. In a heat exchanger incorporating the apparatus, the electrodes are conduits conveying a fluid to be heated. The two particle types alternately contact each conduit to transfer heat from a hot gas flow to the second fluid within the conduit.

Removal of p-xylene from an air stream in a hybrid biofilter.

PubMed

Wu, Dan; Quan, Xie; Zhao, Yazhi; Chen, Shuo

2006-08-21

Biofiltration of an air stream containing p-xylene has been studied in a laboratory hybrid biofilter packed with a mixture of mature pig compost, forest soil and the packing material which was made of polyethylene (PE) and used in the moving bed biological reactor (MBBR) in wastewater treatment. Three flow rates, 9.17, 19.87 and 40.66 m(3)m(-2)h(-1), were investigated for p-xylene inlet concentration ranging from 0.1 to 3.3 g m(-3). A high elimination capacity of 80 g m(-3)h(-1) corresponding to removal efficiency of 96% was obtained at a flow rate of 9.17 m(3)m(-2)h(-1) (empty bed residence time of 132 s). At a flow rate of 40.66 m(3)m(-2)h(-1) (empty bed residence time of 30s), the maximum elimination capacity for p-xylene was 40 g m(-3)h(-1) and removal efficiencies were in the range of 47-100%. The production of carbon dioxide (P(CO(2))) is proportional to elimination capacity (EC) and the linear relation was formulated as P(CO(2))=1.65EC+15.58. Stable pH values ranging from 6.3 to 7.6 and low pressure drop values less than 0.2 cm H(2)O (19.6 Pa) of packing media in compost-based biofilter of hybrid biofilter were observed, which avoided acidification and compaction of packing media and sustained the activity of microorganism populations.

Capacity and Utilization in Health Care: The Effect of Empty Beds on Neonatal Intensive Care Admission

PubMed Central

Freedman, Seth

2016-01-01

Because geographic variation in medical care utilization is jointly determined by both supply and demand, it is difficult to empirically estimate whether capacity itself has a causal impact on utilization in health care. In this paper, I exploit short-term variation in Neonatal Intensive Care Unit (NICU) capacity that is unlikely to be correlated with unobserved demand determinants. I find that available NICU beds have little to no effect on NICU utilization for the sickest infants, but do increase utilization for those in the range of birth weights where admission decisions are likely to be more discretionary. PMID:27942353

Pulse enhanced fluidized bed combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mueller, B.

1996-12-31

Information is outlined on pulse enhanced fluidized bed combustion. The following topics are discussed: what is pulse enhanced fluidized bed combustion?; pulse combustors; pulsed atmospheric fluidized bed combustor (PAFBC); advantages of PAFBC; performance advantages; PAFBC facts; and PAFBC contact points.

Growth of Fault-Cored Anticlines by Flexural Slip Folding: Analysis by Boundary Element Modeling

NASA Astrophysics Data System (ADS)

Johnson, Kaj M.

2018-03-01

Fault-related folds develop due to a combination of slip on the associated fault and distributed deformation off the fault. Under conditions that are sufficient for sedimentary layering to act as a stack of mechanical layers with contact slip, buckling can dramatically amplify the folding process. We develop boundary element models of fault-related folding of viscoelastic layers embedded with a reverse fault to examine the influence of such layering on fold growth. The strength of bedding contacts, the thickness and stiffness of layering, and fault geometry all contribute significantly to the resulting fold form. Frictional contact strength between layers controls the degree of localization of slip within fold limbs; high contact friction in relatively thin bedding tends to localize bedding slip within narrow kink bands on fold limbs, and low contact friction tends to produce widespread bedding slip and concentric fold form. Straight ramp faults tend to produce symmetric folds, whereas listric faults tend to produce asymmetric folds with short forelimbs and longer backlimbs. Fault-related buckle folds grow exponentially with time under steady loading rates. At early stages of folding, fold growth is largely attributed to slip on the fault, but as the fold increases amplitude, a larger portion of the fold growth is attributed to distributed slip across bedding contacts on the limbs of the fold. An important implication for geologic and earthquake studies is that not all surface deformation associated with blind reverse faults may be attributed to slip on the fault during earthquakes.

Cystoscopy and Ureteroscopy

MedlinePlus

... urinary urgency—the inability to delay urination urinary retention —the inability to empty the bladder completely urinary ... Coordinating Committees Strategic Plans & Reports Research Areas FAQs Jobs at NIDDK Visit Us Contact Us News News ...

Hospitals' vertical integration into skilled nursing: a rational approach to controlling transaction costs.

PubMed

Lehrman, S; Shore, K K

1998-01-01

Using 1985 and 1988 American Hospital Association data, this study examines 1,523 hospitals nationwide and concludes that hospitals' ownership of skilled nursing facilities helps minimize the transaction costs associated with post-acute patient transfers while productively using empty hospital beds. Unfortunately, such ownership creates complex cost, quality, and accessibility trade-offs in terms of the skilled nursing care provided.

Optimization of arsenic removal water treatment system through characterization of terminal electron accepting processes.

PubMed

Upadhyaya, Giridhar; Clancy, Tara M; Brown, Jess; Hayes, Kim F; Raskin, Lutgarde

2012-11-06

Terminal electron accepting process (TEAP) zones developed when a simulated groundwater containing dissolved oxygen (DO), nitrate, arsenate, and sulfate was treated in a fixed-bed bioreactor system consisting of two reactors (reactors A and B) in series. When the reactors were operated with an empty bed contact time (EBCT) of 20 min each, DO-, nitrate-, sulfate-, and arsenate-reducing TEAP zones were located within reactor A. As a consequence, sulfate reduction and subsequent arsenic removal through arsenic sulfide precipitation and/or arsenic adsorption on or coprecipitation with iron sulfides occurred in reactor A. This resulted in the removal of arsenic-laden solids during backwashing of reactor A. To minimize this by shifting the sulfate-reducing zone to reactor B, the EBCT of reactor A was sequentially lowered from 20 min to 15, 10, and 7 min. While 50 mg/L (0.81 mM) nitrate was completely removed at all EBCTs, more than 90% of 300 μg/L (4 μM) arsenic was removed with the total EBCT as low as 27 min. Sulfate- and arsenate-reducing bacteria were identified throughout the system through clone libraries and quantitative PCR targeting the 16S rRNA, dissimilatory (bi)sulfite reductase (dsrAB), and dissimilatory arsenate reductase (arrA) genes. Results of reverse transcriptase (RT) qPCR of partial dsrAB (i.e., dsrA) and arrA transcripts corresponded with system performance. The RT qPCR results indicated colocation of sulfate- and arsenate-reducing activities, in the presence of iron(II), suggesting their importance in arsenic removal.

Infrared video tracking of Anopheles gambiae at insecticide-treated bed nets reveals rapid decisive impact after brief localised net contact

PubMed Central

Parker, Josephine E.A.; Angarita-Jaimes, Natalia; Abe, Mayumi; Towers, Catherine E.; Towers, David; McCall, Philip J.

2015-01-01

Long-lasting insecticidal bed nets (LLINs) protect humans from malaria transmission and are fundamental to malaria control worldwide, but little is known of how mosquitoes interact with nets. Elucidating LLIN mode of action is essential to maintain or improve efficacy, an urgent need as emerging insecticide resistance threatens their future. Tracking multiple free-flying Anopheles gambiae responding to human-occupied bed nets in a novel large-scale system, we characterised key behaviours and events. Four behavioural modes with different levels of net contact were defined: swooping, visiting, bouncing and resting. Approximately 75% of all activity occurred at the bed net roof where multiple brief contacts were focussed above the occupant’s torso. Total flight and net contact times were lower at LLINs than untreated nets but the essential character of the response was unaltered. LLINs did not repel mosquitoes but impacted rapidly: LLIN contact of less than 1 minute per mosquito during the first ten minutes reduced subsequent activity; after thirty minutes, activity at LLINs was negligible. Velocity measurements showed that mosquitoes detected nets, including unbaited untreated nets, prior to contact. This is the most complete characterisation of mosquito-LLIN interactions to date, and reveals many aspects of LLIN mode of action, important for developing the next generation of LLINs. PMID:26323965

Emission studies from combustion of empty fruit bunch pellets in a fluidized bed combustor

NASA Astrophysics Data System (ADS)

Fazli Othaman, Muhamad; Sabudin, Sulastri; Faizal Mohideen Batcha, Mohd

2017-08-01

Malaysia is producing a very large amount of biomass annually from milling activities of oil palm. This biomass is currently being used efficiently in many ways including as fuel for boilers together with fossil fuels. This paper reports the emission characteristics from biomass combustion in a swirling fluidized bed combustor (SFBC). Pelletized empty fruit bunch (PEFB), one of largest biomass produced from oil palm industries were used as fuel in the present study. Combustion experiments were conducted with several quantitiesof excess air: 20%, 40%, 60% and 80% for a constant fuel feedrate of 30kg/hr. The effect of excess air was investigated for three major emissions gaseous namely CO, CO2 and NOx. Fly ash produced from the combustion was also analysed to find the contents of unburnt carbon and other impurities. From the results, it was found that the emission of CO decreased from 64 ppm to 40 ppm while the amount of CO2 increased slightly with the increasing of excess air from 20% to 80%. The NOx emission also increased from 290 ppm to 350 ppm because of N2 in the EA reacts with O2 due to high combustion temperature. The combustion efficiencies of about 99% obtained in the present study, showing the prospects of using SFBC in commercial scale.

Technical Note: Bed conduction impact on fiber optic DTS water temperature measurements

NASA Astrophysics Data System (ADS)

O'Donnell Meininger, T.; Selker, J. S.

2014-07-01

Error in Distributed Temperature Sensor (DTS) water temperature measurements may be introduced by contact of the fiber optic cable sensor with bed materials (e.g., seafloor, lakebed, stream bed). Heat conduction from the bed materials can affect cable temperature and the resulting DTS measurements. In the Middle Fork John Day River, apparent water temperature measurements were influenced by cable sensor contact with aquatic vegetation and fine sediment bed materials. Affected cable segments measured a diurnal temperature range reduced by 10% and lagged by 20-40 min relative to that of ambient stream temperature. The diurnal temperature range deeper within the vegetation-sediment bed material was reduced 70% and lagged 240 min relative to ambient stream temperature. These site-specific results illustrate the potential magnitude of bed-conduction impacts with buried DTS measurements. Researchers who deploy DTS for water temperature monitoring should understand the importance of the environment into which the cable is placed on the range and phase of temperature measurements.

Flash hydrogenation of coal

DOEpatents

Manowitz, Bernard; Steinberg, Meyer; Sheehan, Thomas V.; Winsche, Warren E.; Raseman, Chad J.

1976-01-01

A process for the hydrogenation of coal comprising the contacting of powdered coal with hydrogen in a rotating fluidized bed reactor. A rotating fluidized bed reactor suitable for use in this process is also disclosed. The coal residence time in the reactor is limited to less than 5 seconds while the hydrogen contact time is not in excess of 0.2 seconds.

Removal of trace organic micropollutants by drinking water biological filters.

PubMed

Zearley, Thomas L; Summers, R Scott

2012-09-04

The long-term removal of 34 trace organic micropollutants (<1 μg L(-1)) was evaluated and modeled in drinking water biological filters with sand media from a full-scale plant. The micropollutants included pesticides, pharmaceuticals, and personal care products, some of which are endocrine disrupting chemicals, and represent a wide range of uses, chemical structures, adsorbabilities, and biodegradabilities. Micropollutant removal ranged from no measurable removal (<15%) for 13 compounds to removal below the detection limit and followed one of four trends over the one year study period: steady state removal throughout, increasing removal to steady state (acclimation), decreasing removal, or no removal (recalcitrant). Removals for all 19 nonrecalcitrant compounds followed first-order kinetics when at steady state with increased removal at longer empty bed contact times (EBCT). Rate constants were calculated, 0.02-0.37 min(-1), and used in a pseudo-first-order rate model with the EBCT to predict removals in laboratory biofilters at a different EBCT and influent conditions. Drinking water biofiltration has the potential to be an effective process for the control of many trace organic contaminants and a pseudo-first-order model can serve as an appropriate method for approximating performance.

Decontamination of combustion gases in fluidized bed incinerators

DOEpatents

Leon, Albert M.

1982-01-01

Sulfur-containing atmospheric pollutants are effectively removed from exit gas streams produced in a fluidized bed combustion system by providing a fluidized bed of particulate material, i.e. limestone and/or dolomite wherein a concentration gradient is maintained in the vertical direction. Countercurrent contacting between upwardly directed sulfur containing combustion gases and descending sorbent particulate material creates a concentration gradient across the vertical extent of the bed characterized in progressively decreasing concentration of sulfur, sulfur dioxide and like contaminants upwardly and decreasing concentration of e.g. calcium oxide, downwardly. In this manner, gases having progressively decreasing sulfur contents contact correspondingly atmospheres having progressively increasing concentrations of calcium oxide thus assuring optimum sulfur removal.

Novel non-contact control system of electric bed for medical healthcare.

PubMed

Lo, Chi-Chun; Tsai, Shang-Ho; Lin, Bor-Shyh

2017-03-01

A novel non-contact controller of the electric bed for medical healthcare was proposed in this study. Nowadays, the electric beds are widely used for hospitals and home-care, and the conventional control method of the electric beds usually involves in the manual operation. However, it is more difficult for the disabled and bedridden patients, who might totally depend on others, to operate the conventional electric beds by themselves. Different from the current controlling method, the proposed system provides a new concept of controlling the electric bed via visual stimuli, without manual operation. The disabled patients could operate the electric bed by focusing on the control icons of a visual stimulus tablet in the proposed system. Besides, a wearable and wireless EEG acquisition module was also implemented to monitor the EEG signals of patients. The experimental results showed that the proposed system successfully measured and extracted the EEG features related to visual stimuli, and the disabled patients could operate the adjustable function of the electric bed by themselves to effectively reduce the long-term care burden.

An Experimental Test of Factors Attracting Deer Mice into Buildings.

PubMed

Kuenzi, Amy J; Douglass, Richard

2009-09-01

Deer mice (Peromyscus maniculatus) are the principal reservoir host of Sin Nombre virus (SNV). Deer mice use a wide variety of habitats including peridomestic settings in and around human dwellings, their presence in and around homes has been implicated as a risk factor for acquiring Hantavirus Pulmonary Syndrome. Deer mice are believed to enter buildings in order to gain access to a variety of resources including food, bedding material, and better thermal microclimates. However, no one has experimentally tested which factors influence mice use of buildings. We conducted experiments using small simulated buildings to determine the effects of two factors, i.e., food and bedding material, on mouse activity in these buildings. We also examined if these effects varied with time of year. We found that deer mice entered our buildings regardless of the presence or absence of food or bedding. However, the amount of activity in buildings was affected by what they contained. We found significantly higher indices of activity in buildings containing food compared to both empty buildings (control) and buildings containing bedding material. Time of year did not affect activity in buildings.

Electrical Resistivity Measurement of Petroleum Coke Powder by Means of Four-Probe Method

NASA Astrophysics Data System (ADS)

Rouget, G.; Majidi, B.; Picard, D.; Gauvin, G.; Ziegler, D.; Mashreghi, J.; Alamdari, H.

2017-10-01

Carbon anodes used in Hall-Héroult electrolysis cells are involved in both electrical and chemical processes of the cell. Electrical resistivity of anodes depends on electrical properties of its constituents, of which carbon coke aggregates are the most prevalent. Electrical resistivity of coke aggregates is usually characterized according to the ISO 10143 standardized test method, which consists of measuring the voltage drop in the bed of particles between two electrically conducing plungers through which the current is also applied. Estimation of the electrical resistivity of coke particles from the resistivity of particle bed is a challenging task and needs consideration of the contribution of the interparticle void fraction and the particle/particle contact resistances. In this work, the bed resistivity was normalized by subtracting the interparticle void fraction. Then, the contact size was obtained from discrete element method simulation and the contact resistance was calculated using Holm's theory. Finally, the resistivity of the coke particles was obtained from the bed resistivity.

Hand-touch contact assessment of high-touch and mutual-touch surfaces among healthcare workers, patients, and visitors.

PubMed

Cheng, V C C; Chau, P H; Lee, W M; Ho, S K Y; Lee, D W Y; So, S Y C; Wong, S C Y; Tai, J W M; Yuen, K Y

2015-07-01

Unlike direct contact with patients' body, hand hygiene practice is often neglected by healthcare workers (HCWs) and visitors after contact with patients' environment. Contact with hospital environmental items may increase risk of pathogen transmission. To enumerate the number of hand-touch contacts by patients, HCWs and visitors with any hospital environmental items. All contact-episodes between person and item were recorded by direct observation in a six-bed cubicle of acute wards for 33 working days. High-touch and mutual-touch items with high contact frequencies by HCWs, patients, and visitors were analysed. In total, 1107 person-episodes with 6144 contact-episodes were observed in 66 observation hours (average: 16.8 person-episodes and 93.1 contact-episodes per hour). Eight of the top 10 high-touch items, including bedside rails, bedside tables, patients' bodies, patients' files, linen, bed curtains, bed frames, and lockers were mutually touched by HCWs, patients, and visitors. Bedside rails topped the list with 13.6 contact-episodes per hour (mean), followed by bedside tables (12.3 contact-episodes per hour). Using patients' body contacts as a reference, it was found that medical staff and nursing staff contacted bedside tables [rate ratio (RR): 1.741, 1.427, respectively] and patients' files (RR: 1.358, 1.324, respectively) more than patients' bodies, and nursing staff also contacted bedside rails (RR: 1.490) more than patients' bodies. Patients' surroundings may be links in the transmission of nosocomial infections because many are frequently touched and mutually contacted by HCWs, patients, and visitors. Therefore, the focus of hand hygiene education, environmental disinfection, and other system changes should be enhanced with respect to high-touch and mutual-touch items. Copyright © 2015 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Bed conduction impact on fiber optic distributed temperature sensing water temperature measurements

NASA Astrophysics Data System (ADS)

O'Donnell Meininger, T.; Selker, J. S.

2015-02-01

Error in distributed temperature sensing (DTS) water temperature measurements may be introduced by contact of the fiber optic cable sensor with bed materials (e.g., seafloor, lakebed, streambed). Heat conduction from the bed materials can affect cable temperature and the resulting DTS measurements. In the Middle Fork John Day River, apparent water temperature measurements were influenced by cable sensor contact with aquatic vegetation and fine sediment bed materials. Affected cable segments measured a diurnal temperature range reduced by 10% and lagged by 20-40 min relative to that of ambient stream temperature. The diurnal temperature range deeper within the vegetation-sediment bed material was reduced 70% and lagged 240 min relative to ambient stream temperature. These site-specific results illustrate the potential magnitude of bed-conduction impacts with buried DTS measurements. Researchers who deploy DTS for water temperature monitoring should understand the importance of the environment into which the cable is placed on the range and phase of temperature measurements.

Debris-bed friction of hard-bedded glaciers

USGS Publications Warehouse

Cohen, D.; Iverson, N.R.; Hooyer, T.S.; Fischer, U.H.; Jackson, M.; Moore, P.L.

2005-01-01

[1] Field measurements of debris-bed friction on a smooth rock tablet at the bed of Engabreen, a hard-bedded, temperate glacier in northern Norway, indicated that basal ice containing 10% debris by volume exerted local shear traction of up to 500 kPa. The corresponding bulk friction coefficient between the dirty basal ice and the tablet was between 0.05 and 0.08. A model of friction in which nonrotating spherical rock particles are held in frictional contact with the bed by bed-normal ice flow can account for these measurements if the power law exponent for ice flowing past large clasts is 1. A small exponent (n < 2) is likely because stresses in ice are small and flow is transient. Numerical calculations of the bed-normal drag force on a sphere in contact with a flat bed using n = 1 show that this force can reach values several hundred times that on a sphere isolated from the bed, thus drastically increasing frictional resistance. Various estimates of basal friction are obtained from this model. For example, the shear traction at the bed of a glacier sliding at 20 m a-1 with a geothermally induced melt rate of 0.006 m a-1 and an effective pressure of 300 kPa can exceed 100 kPa. Debris-bed friction can therefore be a major component of sliding resistance, contradicting the common assumption that debris-bed friction is negligible. Copyright 2005 by the American Geophysical Union.

Qualitative numerical study of simultaneous high-G-intensified gas–solids contact, separation and segregation in a bi-disperse rotating fluidized bed in a vortex chamber

DOE PAGES

De Wilde, Juray; Richards, George; Benyahia, Sofiane

2016-05-13

Coupled discrete particle method – computational fluid dynamics simulations are carried out to demonstrate the potential of combined high-G-intensified gas-solids contact, gas-solids separation and segregation in a rotating fluidized bed in a static vortex chamber. A case study with two distinct types of particles is focused on. When feeding solids using a standard solids inlet design, a dense and uniform rotating fluidized bed is formed, guaranteeing intense gas-solids contact. The presence of both types of particles near the chimney region reduces, however, the strength of the central vortex and is detrimental for separation and segregation. Optimization of the solids inletmore » design is required, as illustrated by stopping the solids feeding. High-G separation and segregation of the batch of particles is demonstrated, as the strength of the central vortex is restored. The flexibility with respect to the gas flow rate of the bed density and uniformity and of the gas-solids separation and segregation is demonstrated, a unique feature of vortex chamber generated rotating fluidized beds. With the particles considered in this case study, turbulent dispersion by large eddies in the gas phase is shown to have only a minor impact on the height of the inner bed of small/light particles.« less

Coaxial EMI Sensor for UXO Detection and Discrimination

DTIC Science & Technology

2008-05-01

Raleigh, North Carolina. Geophex has a 10 m x 10 m test bed in which 21 metal pipes of various sizes, some ferrous (steel) and some nonferrous (3...spectral matching was expected to lower the FAR, but with the wide range of anticipated UXO in terms of size and metal content, the corresponding wide...warrant further investigation.” Grid squares with a response stage below the stated noise threshold are declared empty (neither UXO nor metallic

Performance of granular activated carbon to remove micropollutants from municipal wastewater-A meta-analysis of pilot- and large-scale studies.

PubMed

Benstoem, Frank; Nahrstedt, Andreas; Boehler, Marc; Knopp, Gregor; Montag, David; Siegrist, Hansruedi; Pinnekamp, Johannes

2017-10-01

For reducing organic micropollutants (MP) in municipal wastewater effluents, granular activated carbon (GAC) has been tested in various studies. We did systematic literature research and found 44 studies dealing with the adsorption of MPs (carbamazepine, diclofenac, sulfamethoxazole) from municipal wastewater on GAC in pilot- and large-scale plants. Within our meta-analysis we plot the bed volumes (BV [m 3 water /m 3 GAC ]) until the breakthrough criterion of MP-BV20% was reached, dependent on potential relevant parameters (empty bed contact time EBCT, influent DOC DOC 0 and manufacturing method). Moreover, we performed statistical tests (ANOVAs) to check the results for significance. Single adsorbers operating time differs i.e. by 2500% until breakthrough of diclofenac-BV20% was reached (800-20,000 BV). There was still elimination of the "very well/well" adsorbable MPs such as carbamazepine and diclofenac even when the equilibrium of DOC had already been reached. No strong statistical significance of EBCT and DOC 0 on MP-BV20% could be found due to lack of data and the high heterogeneity of the studies using GAC of different qualities. In further studies, adsorbers should be operated ≫20,000 BV for exact calculation of breakthrough curves, and the following parameters should be recorded: selected MPs; DOC 0; UVA 254 ; EBCT; product name, manufacturing method and raw material of GAC; suspended solids (TSS); backwash interval; backwash program and pressure drop within adsorber. Based on our investigations we generally recommend using reactivated GAC to reduce the environmental impact and to carry out tests on pilot scale to collect reliable data for process design. Copyright © 2017 Elsevier Ltd. All rights reserved.

Co-bedding as a Comfort measure For Twins undergoing painful procedures (CComForT Trial)

PubMed Central

2009-01-01

Background Co-bedding, a developmental care strategy, is the practice of caring for diaper clad twins in one incubator (versus separating and caring for each infant in separate incubators), thus creating the opportunity for skin-to-skin contact and touch between the twins. In studies of mothers and their infants, maternal skin-to-skin contact has been shown to decrease procedural pain response according to both behavioral and physiological indicators in very preterm neonates. It is uncertain if this comfort is derived solely from maternal presence or from stabilization of regulatory processes from direct skin contact. The intent of this study is to compare the comfort effect of co-bedding (between twin infants who are co-bedding and those who are not) on infant pain response and physiologic stability during a tissue breaking procedure (heelstick). Methods/Design Medically stable preterm twin infants admitted to the Neonatal Intensive Care Unit will be randomly assigned to a co-bedding group or a standard care group. Pain response will be measured by physiological and videotaped facial reaction using the Premature Infant Pain Profile scale (PIPP). Recovery from the tissue breaking procedure will be determined by the length of time for heart rate and oxygen saturation to return to baseline. Sixty four sets of twins (n = 128) will be recruited into the study. Analysis and inference will be based on the intention-to-treat principle. Discussion If twin contact while co-bedding is determined to have a comforting effect for painful procedures, then changes in current neonatal care practices to include co-bedding may be an inexpensive, non invasive method to help maintain physiologic stability and decrease the long term psychological impact of procedural pain in this high risk population. Knowledge obtained from this study will also add to existing theoretical models with respect to the exact mechanism of comfort through touch. Trial registration NCT00917631 PMID:20003351

Installation Restoration Program. Phase 1. Records Search Andrews AFB. Maryland

DTIC Science & Technology

1985-06-01

red to silvery-qrey, functions ma a conf ining bed. Formation. ~Va plastics thin lonses of pole gray silt. Ann"a Formation. ye (0-210 sand, qrsenieh...the Nanjemoy Formation (a clayey glauconi- tic sand, two to thirty feet thick) and the Marlboro Clay (a plastic clay with silt partings, two to... plastics , empty 55-gallon drums, waste lumber, tires, pipes, and hospital wastes such as unused needles and chemical reagents. In the past, Site D-4 was

Plasma dynamics in a packed bed dielectric barrier discharge (DBD) operated in helium

NASA Astrophysics Data System (ADS)

Mujahid, Zaka-ul-Islam; Hala, Ahmed

2018-03-01

Packed bed dielectric barrier discharges (DBDs) are very promising for several applications including remediation of environmental pollutants and greenhouse gas conversion. In this work, we have investigated the space and time-resolved emission from a packed bed DBD operated in helium, to understand the plasma dynamics. We have chosen a simple planar DBD arrangement with a patterned dielectric, which mimics the spherical boundaries between the dielectric pellets and allows the optical access to the plasma. The results show that plasma is sustained in a packed bed DBD by three mechanisms: filamentary discharge in the void (between the center of dielectric structures and the opposite electrode), microdischarges at the contact points and surface ionization waves over the dielectric surface. It is observed that for most of the duration plasma is generated at the contact points between the dielectric structures.

Relationship between healthcare worker surface contacts, care type and hand hygiene: an observational study in a single-bed hospital ward.

PubMed

King, M-F; Noakes, C J; Sleigh, P A; Bale, S; Waters, L

2016-09-01

This study quantifies the relationship between hand hygiene and the frequency with which healthcare workers (HCWs) touch surfaces in patient rooms. Surface contacts and hand hygiene were recorded in a single-bed UK hospital ward for six care types. Surface contacts often formed non-random patterns, but hygiene before or after patient contact depends significantly on care type (P=0.001). The likelihood of hygiene correlated with the number of surface contacts (95% confidence interval 1.1-5.8, P=0.002), but not with time spent in the room. This highlights that a potential subconscious need for hand hygiene may have developed in HCWs, which may support and help focus future hygiene education programmes. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

A review: Potential and challenges of biologically activated carbon to remove natural organic matter in drinking water purification process.

PubMed

Korotta-Gamage, Shashika Madushi; Sathasivan, Arumugam

2017-01-01

The use of biologically activated carbon (BAC) in drinking water purification is reviewed. In the past BAC is seen mostly as a polishing treatment. However, BAC has the potential to provide solution to recent challenges faced by water utilities arising from change in natural organic matter (NOM) composition in drinking water sources - increased NOM concentration with a larger fraction of hydrophilic compounds and ever increasing trace level organic pollutants. Hydrophilic NOM is not removed by traditional coagulation process and causes bacterial regrowth and increases disinfection by-products (DBPs) formation during disinfection. BAC can offer many advantages by removing hydrophilic fraction and many toxic and endocrine compounds which are not otherwise removed. BAC can also aid the other downstream processes if used as a pre-treatment. Major drawback of BAC was longer empty bed contact time (EBCT) required for an effective NOM removal. This critical review analyses the strategies that have been adopted to enhance the biological activity of the carbon by operational means and summarises the surface modification methods. To maximize the benefit of the BAC, a rethink of current treatment plant configuration is proposed. If the process can be expedited and adopted appropriately, BAC can solve many of the current problems. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Elimination of As(V) by bead cellulose adsorbent loaded with Fe (beta-FeOOH) from groundwater].

PubMed

Guo, Xue-jun; Chen, Fu-hua

2005-05-01

A new adsorbent, bead cellulose impregnated with Fe oxide hydroxide (beta-FeOOH) was prepared, which is porous and has excellent mechanical properties. The content of iron, the reactive center of the adsorbent was 360 mg/mL at the most (50% in mass). Batch sorption experiments show that the adsorbent had 15.6 mg/mL (33.2 mg/g) of As(V) maximum sorption while the iron content was 220 mg/mL. The adsorbent had good kinetic property for arsenate and the adsorption equilibrium reached in 10 h. The sorption kinetic data can be described by Lagergren pseudo-second order rate equation. The addition of chloride, sulfate and silicate did not affecte the arsenic adsorption. The column experiment indicated that the breakthrough bed volume was 5000 BV while influent As(V) concentration was 500 microg/L and empty contact time was 5.9 min. The spent adsorbent can be regenerated eluting with 1.5 mol x L(-1) NaOH solutions, and the desorption and regeneration process were more than 90%. The FeOOH was chemically stable during the column adsorption and regeneration. The preparation method is simple and innovative. The adsorbent has good future applying for the arsenic removal from groundwater and drinking water.

Adsorption of selected pharmaceuticals and an endocrine disrupting compound by granular activated carbon. 2. Model prediction.

PubMed

Yu, Zirui; Peldszus, Sigrid; Huck, Peter M

2009-03-01

The adsorption of two representative pharmaceutically active compounds (PhACs)-naproxen and carbamazepine and one endocrine disrupting compound (EDC)-nonylphenol was studied in pilot-scale granular activated carbon (GAC) adsorbers using post-sedimentation (PS) water from a full-scale drinking water treatment plant. Acidic naproxen broke through fastest while nonylphenol was removed best, which was consistent with the degree to which fouling affected compound removals. Model predictions and experimental data were generally in good agreement for all three compounds, which demonstrated the effectiveness and robustness of the pore and surface diffusion model (PSDM) used in combination with the time-variable parameter approach for predicting removals at environmentally relevant concentrations (i.e., ng/L range). Sensitivity analyses suggested that accurate determination of film diffusion coefficients was critical for predicting breakthrough for naproxen and carbamazepine, in particular when high removals are targeted. Model simulations demonstrated that GAC carbon usage rates (CURs) for naproxen were substantially influenced by the empty bed contact time (EBCT) at the investigated conditions. Model-based comparisons between GAC CURs and minimum CURs for powdered activated carbon (PAC) applications suggested that PAC would be most appropriate for achieving 90% removal of naproxen, whereas GAC would be more suitable for nonylphenol.

Surface free energy analysis of oil palm empty fruit bunches fiber reinforced biocomposites

NASA Astrophysics Data System (ADS)

Suryadi, G. S.; Nikmatin, S.; Sudaryanto; Irmansyah; Sukaryo, S. G.

2017-05-01

Study of the size effect of natural fiber from oil palm empty fruit bunches (OPEFB) as filler, onto the contact angle and surface free energy of fiber reinforced biocomposites has been done. The OPEFB fibers were prepared by mechanical milling and sieving to obtain various sizes of fiber (long-fiber, medium-fiber, short-fiber, and microparticle). The biocomposites has been produced by extrusion using single-screw extruder with EFB fiber as filler, recycled Acrylonitrile Butadiene Styrene (ABS) polymer as matrix, and primary antioxidant, acid scavanger, and coupling agent as additives. The obtained biocomposites in form of granular, were made into test piece by injection molding method. Contact angles of water, methanol, and hexane on the surface of biocomposites at room temperature were measured using Phoenix 300 Contact Angle Analyzer. The surface free energy (SFE) and their components were calculated using three previous known methods (Girifalco-Good-Fowkes-Young (GGFY), Owens-Wendt, and van Oss-Chaudhury-Good (vOCG)). The results showed that total SFE of Recycled ABS as control was about 24.38 mJ/m2, and SFE of biocomposites was lower than control, decreased with decreasing of EFB fiber size as biocomposites filler. The statistical analysis proved that there are no statistically significant differences in the value of the SFE calculated with the three different methods.

Application of bacteriophages to selectively remove Pseudomonas aeruginosa in water and wastewater filtration systems.

PubMed

Zhang, Yanyan; Hunt, Heather K; Hu, Zhiqiang

2013-09-01

Water and wastewater filtration systems often house pathogenic bacteria, which must be removed to ensure clean, safe water. Here, we determine the persistence of the model bacterium Pseudomonas aeruginosa in two types of filtration systems, and use P. aeruginosa bacteriophages to determine their ability to selectively remove P. aeruginosa. These systems used beds of either anthracite or granular activated carbon (GAC), which were operated at an empty bed contact time (EBCT) of 45 min. The clean bed filtration systems were loaded with an instantaneous dose of P. aeruginosa at a total cell number of 2.3 (± 0.1 [standard deviation]) × 10(7) cells. An immediate dose of P. aeruginosa phages (1 mL of phage stock at the concentration of 2.7 × 10(7) PFU (Plaque Forming Units)/mL) resulted in a reduction of 50% (± 9%) and >99.9% in the effluent P. aeruginosa concentrations in the clean anthracite and GAC filters, respectively. To further evaluate the effects of P. aeruginosa phages, synthetic stormwater was run through anthracite and GAC biofilters where mixed-culture biofilms were present. Eighty five days after an instantaneous dose of P. aeruginosa (2.3 × 10(7) cells per filter) on day 1, 7.5 (± 2.8) × 10(7) and 1.1 (± 0.5) × 10(7) P. aeruginosa cells/g filter media were detected in the top layer (close to the influent port) of the anthracite and GAC biofilters, respectively, demonstrating the growth and persistence of pathogenic bacteria in the biofilters. A subsequent 1-h dose of phages, at the concentration of 5.1 × 10(6) PFU/mL and flow rate of 1.6 mL/min, removed the P. aeruginosa inside the GAC biofilters and the anthracite biofilters by 70% (± 5%) and 56% (± 1%), respectively, with no P. aeruginosa detected in the effluent, while not affecting ammonia oxidation or the ammonia-oxidizing bacterial community inside the biofilters. These results suggest that phage treatment can selectively remove pathogenic bacteria with minimal impact on beneficial organisms from attached growth systems for effluent quality improvement. Copyright © 2013 Elsevier Ltd. All rights reserved.

Do-it-yourself Bed Bug Control

MedlinePlus

... Contact Us Share Do-it-yourself Bed Bug Control Información relacionada disponible en español Can you treat ... all of the residents to participate. Achieving complete control can take weeks to months, depending on the ...

Biofiltration of odors, toxics and volatile organic compounds from publicly owned treatment works

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webster, T.S.; Devinny, J.S.; Torres, E.M.

1996-12-31

Increasing federal and state regulation has made it necessary to apply air pollution control measures at publicly owned treatment works (POTWs). Traditional control technologies may not be suitable for treating the low and variable contaminant concentrations often found in POTW off-gases. An alternative control technology, biofiltration, was studied. An experiment using bench- and pilot-scale reactors established optimal operating conditions for a full-scale conceptual design. The waste airstream contained ppmv levels of hydrogen sulfide and ppbv levels of specific volatile organic compounds (VOCs). Granular activated carbon (GAC) and yard waste compost (YWG) were tested as possible biofilter media with and withoutmore » pH control. The 16-month field study bench reactors achieved 99% removal of hydrogen sulfide, 53 to 98% removal of aromatic hydrocarbons, 37 to 95% removal of aldehydes and ketones, and 0 to 85% removal of chlorinated compounds. The GAC and YWC pilot reactors removed more than 80% and 65% of the total VOCs at 17 second and 70 second empty bed retention times, respectively. The YWC reactors performed poorly at empty bed retention times of 30 and 45 seconds, removing less than 40% of total VOCs. Declining pH had little negative effect on contaminant removal, suggesting costly control measures may not be necessary. Biofiltration appears to be a feasible alternative to traditional control technologies in treating off-gases from POTWs. 13 refs., 3 figs., 4 tabs.« less

The Ontogeny of Diurnal Rhythmicity in Bed-Sharing and Solitary-Sleeping Infants: A Preliminary Report

ERIC Educational Resources Information Center

Burnham, Melissa M.

2007-01-01

The purpose of the current study was to investigate the development of sleep-wake and melatonin diurnal rhythms over the first 3 months of life, and the potential effect of bed-sharing on their development. It was hypothesized that increased maternal contact through bed-sharing would affect the development of rhythms in human infants. Ten…

Enhanced biofiltration using cell attachment promotors.

PubMed

Goncalves, Juan J; Govind, Rakesh

2009-02-15

H2S polluted airstreams were treated in two biotrickling filter columns packed with polyurethane (PU) foam cubes, one with cubes coated with a solution of 25 mg/L of polyethyleneimine (PEI, coated reactor) and the other containing just plain PU cubes (uncoated reactor) at empty bed residence times (EBRT) ranging from 6 to 60 s. and inlet H2S concentrations ranging from 30 to 235 ppm, (overall loads of up to 44 gH2S/m3bed/h), with overall removal efficiencies (RE) in the range of 90-100% over 125 days. The acclimatization characteristics of the coated reactor outperformed those of the uncoated one, and both the observed elimination capacity (EC) of 77 gH2S/m3bed/h and retention of volatile solids (VS) of 42 mgVS/cube were maxima in the coated reactor. Insights into the controlling removal mechanisms were also provided by means of dimensionless analysis of the experimental data. Denaturing gradient gel electrophoresis (DGGE) showed that the dominant surviving species in both units belonged to the genus Acidithiobacillus.

Three-dimensional reconstruction of the angioarchitecture of the ciliary body of the West Indian manatee (Trichechus manatus).

PubMed

Natiello, Michelle; Samuelson, Don

2005-01-01

To examine the angioarchitecture of the ciliary body in the West Indian manatee (Trichechus manatus), through the use of three-dimensional reconstruction. Specimens from West Indian manatee were preserved in 10% buffered formalin, embedded in paraffin, serial sectioned and stained by Masson trichrome for light microscopic three-dimensional reconstruction and evaluation. The network of blood vessels in the ciliary processes of the West Indian manatee is fed by the major arterial circle that lies mostly near the base of the iris. The branching arterioles give rise to a capillary-sinusoidal bed that extends internally along each process, emptying into two sets of veins, one being elevated. The elevated and nonelevated veins join posteriorly before emptying into the choroidal venous system. The angioarchitecture of the ciliary body of the West Indian manatee is clearly unique when compared to those previously examined in land mammals. Three-dimensional reconstruction of paraffin sections is an effective means to evaluate vascular patterns in ocular specimens, especially those unavailable for corrosion casting.

Scalable synthesis of NiMoO4 microspheres with numerous empty nanovoids as an advanced anode material for Li-ion batteries

NASA Astrophysics Data System (ADS)

Park, Jin-Sung; Cho, Jung Sang; Kang, Yun Chan

2018-03-01

Closely in line with advances in next-generation energy storage materials, anode materials for lithium-ion batteries (LIBs) with high capacity and long cycle life have been widely explored. As part of the current effort, nickel molybdate (NiMoO4) microspheres with empty nanovoids are synthesized via spray drying process and subsequent one-step calcination in air. Dextrin in the atomized droplet is phase segregated during the spray drying process and calcined in air atmosphere, resulting in numerous empty nanovoids well-distributed within a microsphere. The empty nanovoids alleviate volume expansion during cycling, shorten lithium-ion diffusion length, and facilitate contact between electrode and electrolyte materials. Along with the high discharge capacity of NiMoO4 material, as high as 1240 mA h g-1 for the 2nd cycle at a high current density of 1 A g-1, uniquity of the structure enables longer cycle life and higher quality performances. The discharge capacity corresponding to the 500th cycle is 1020 mA h g-1 and the capacity retention calculated from the 2nd cycle is 82%. In addition, a discharge capacity of 413 mA g-1 is obtained at an extremely high current density of 10 A g-1.

Altiplano of the Central Andes as seen from STS-66 shuttle Atlantis

NASA Image and Video Library

1994-11-14

This photograph captures the exotic volcanic terrain of the Altiplano of the Central Andes. Some of the remarkable details include the west-pointing wind streaks, resulting from fine dust being transported across the Andes by high winds; paleto (old) shorelines along the margins of the salars (or dry lake beds), recording the changes in water levels on the high Altiplano; beautiful alluvial fans emptying onto some of the salars; and the hundreds of volcanic land forms which can be mapped and interpreted to help decipher the volcanic history of the region.

DNA profiling of trace DNA recovered from bedding.

PubMed

Petricevic, Susan F; Bright, Jo-Anne; Cockerton, Sarah L

2006-05-25

Trace DNA is often detected on handled items and worn clothing examined in forensic laboratories. In this study, the potential transfer of trace DNA to bedding by normal contact, when an individual sleeps in a bed, is examined. Volunteers slept one night on a new, lower bed sheet in their own bed and one night in a bed foreign to them. Samples from the sheets were collected and analysed by DNA profiling. The results indicate that the DNA profile of an individual can be obtained from bedding after one night of sleeping in a bed. The DNA profile of the owner of the bed could also be detected in the foreign bed experiments. Since mixed DNA profiles can be obtained from trace DNA on bedding, caution should be exercised when drawing conclusions from DNA profiling results obtained from such samples. This transfer may have important repercussions in sexual assault investigations.

Microscopic contact area and friction between medical textiles and skin.

PubMed

Derler, S; Rotaru, G-M; Ke, W; El Issawi-Frischknecht, L; Kellenberger, P; Scheel-Sailer, A; Rossi, R M

2014-10-01

The mechanical contact between medical textiles and skin is relevant in the health care for patients with vulnerable skin or chronic wounds. In order to gain new insights into the skin-textile contact on the microscopic level, the 3D surface topography of a normal and a new hospital bed sheet with a regular surface structure was measured using a digital microscope. The topographic data was analysed concerning material distribution and real contact area against smooth surfaces as a function of surface deformations. For contact conditions that are relevant for the skin of patients lying in a hospital bed it was found that the order of magnitude of the ratio of real and apparent contact area between textiles and skin or a mechanical skin model lies between 0.02 and 0.1 and that surface deformations, i.e. penetration of the textile surface asperities into skin or a mechanical skin model, range from 10 to 50µm. The performed analyses of textile 3D surface topographies and comparisons with previous friction measurement results provided information on the relationship between microscopic surface properties and macroscopic friction behaviour of medical textiles. In particular, the new bed sheet was found to be characterised by a trend towards a smaller microscopic contact area (up to a factor of two) and by a larger free interfacial volume (more than a factor of two) in addition to a 1.5 times lower shear strength when in contact with counter-surfaces. The applied methods can be useful to develop improved and skin-adapted materials and surfaces for medical applications. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biofiltration of waste gases containing a mixture of formaldehyde and methanol.

PubMed

Prado, Oscar J; Veiga, María C; Kennes, Christian

2004-08-01

Several biofilters and biotrickling filters were used for the treatment of a mixture of formaldehyde and methanol; and their efficiencies were compared. Results obtained with three different inert filter bed materials (lava rock, perlite, activated carbon) suggested that the packing material had only little influence on the performance. The best results were obtained in a biotrickling filter packed with lava rock and fed a nutrient solution that was renewed weekly. A maximum formaldehyde elimination capacity of 180 g m(-3) h(-1) was reached, while the methanol elimination capacity rose occasionally to more than 600 g m(-3) h(-1). Formaldehyde degradation was affected by the inlet methanol concentration. Several combinations of load vs empty bed residence time (EBRTs of 71.9, 46.5, 30.0, 20.7 s) were studied, reaching a formaldehyde elimination capacity of 112 g m(-3) h(-1) with about 80% removal efficiency at the lowest EBRT (20.7 s).

Ignition of a granular propellant bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wildegger-Gaissmaier, A.E.; Johnston, I.R.

1996-08-01

An experimental and theoretical study is reported on the ignition process of a low vulnerability ammunition (LOVA) propellant bed in a 127-mm (5-in) bore gun charge. The theoretical investigation was with a two-phase flow interior ballistics code and the model predictions showed the marked influence the igniter system can have on pressure wave development, flame spreading, and the overall interior ballistics performance. A number of different igniter systems were investigated in an empty and propellant-filled gun simulator. Pressure, flame spreading, and high-speed film records were used to analyze the ignition/combustion event. The model predictions for flame spreading were confirmed qualitativelymore » by the experimental data. Full-scale instrumented gun firings were conducted with the optimized igniter design. Pressure waves were not detected in the charge during the firings. Model predictions on overall interior ballistics performance agreed well with the firing data.« less

Dust Storm, Aral Sea

NASA Technical Reports Server (NTRS)

2002-01-01

The Aral Sea has shrunk to less than half its size since 1985. The Aral Sea receives little water (sometimes no water) from the two major rivers that empty into it-the Syr Darya and Amu Darya. Instead, the river water is diverted to support irrigation for the region's extensive cotton fields. Recently, water scarcity has increased due to a prolonged drought in Central Asia. As the Aral Sea recedes, its former sea bed is exposed. The Aral's sea bed is composed of fine sediments-including fertilizers and other agricultural chemicals-that are easily picked up by the region's strong winds, creating thick dust storms. The International Space Station crew observed and recorded a large dust storm blowing eastward from the Aral Sea in late June 2001. This image illustrates the strong coupling between human activities (water diversions and irrigation), and rapidly changing land, sea and atmospheric processes-the winds blow across the

Biofiltration of methanol in an organic biofilter using peanut shells as medium.

PubMed

Ramirez-Lopez, E M; Corona-Hernandez, J; Avelar-Gonzalez, F J; Omil, F; Thalasso, F

2010-01-01

Biofiltration consists of a filter-bed of organic matter serving both as carrier for the active biomass and as nutrient supply, through which the polluted gas passes. The selection of a suitable medium material is of major importance to ensure optimum biofilter efficiency. Peanut shells are an agricultural byproduct locally available in large quantities at a low price in most tropical and sub-tropical countries. A previous study showed that peanut shells are physically and chemically suitable for biofiltration. This paper presents the results obtained during a six month biofiltration experiment using peanut shells as medium and methanol as air pollutant. It is shown that peanut shells are potentially suitable as biofiltration medium, since degradation rates of up to 30 kg MeOH/m(3)d with an empty bed residence time of 19s was obtained. The biofilter showed a good resistance to shock load and no operational problems were observed.

Timing of Late Cretaceous Gulf Coast volcanism and chronostratigraphic constraints on deposition of the Ripley Formation from a newly recognized bentonite bed, Pontotoc County, Mississippi

NASA Astrophysics Data System (ADS)

Vitale, E. J.; Gifford, J.; Platt, B. F.

2017-12-01

The Upper Cretaceous Ripley Formation is present throughout the Mississippi (MS) Embayment and contains local bentonite lenses related to regional volcanism. The Pontotoc bentonite is such a lens located near the town of Pontotoc, MS, that was strip-mined and has not been accessible since reclamation of the land. Recent investigations in Pontotoc County south of the Pontotoc bentonite site resulted in the discovery of a previously unknown bentonite bed. Litho- and biostratigraphy indicate that the bentonite is younger than known volcanism from MS. The purposes of the present investigation are 1) to test whether the new bentonite bed is correlative to the Pontotoc bentonite & 2) to recover volcanogenic zircons for U-Pb dating to better constrain timing of volcanism and chronostratigraphy of the Ripley Fm. Outcrops in an active sand pit in the field area expose 2.5 m of fine sand, and an upper gradational contact with an overlying 2.5 m of sandy clay, containing the bentonite bed. Two trenches were excavated through the outcrop, and in each trench a stratigraphic section was measured and bulk samples collected for zircons. Sampling began in the lower bounding sand and continued upsection in 1 m intervals, corresponding to the gradational contact with the bentonite, and 2 locations within the bentonite. The Ripley Fm. consists of 73 m of fossiliferous clay, sand, and calcareous sand beds. Recent stratigraphic revisions of the lateral facies in MS recognize a lower transitional clay facies, a limestone, marl, and calcareous sand facies, a sandy upper Ripley facies, and the formally named Chiwapa Sandstone Member. Ammonite biostratigraphy places the contact between the Chiwapa and the overlying Owl Creek/Prairie Bluff at 68.5 Ma. Unlike the mined area north of Pontotoc where the bentonite is within the Chiwapa, the bed here is directly above the Chiwapa section and its upper contact represents the Ripley Fm. / Owl Creek Fm. contact. Where the bentonite is present, it forms a synchronous surface in this part of the Cretaceous section. This is significant due to it being a potential previously unknown bout of volcanism, which, if the source can be found, implies a new region that may have experienced thermal maturation of hydrocarbon source rocks at a shallower depth than would have been expected under the normal geothermal gradient.

Features of the recovery process of the Kolka glacier after the disaster of 2002

NASA Astrophysics Data System (ADS)

Nosenko, G.; Rototaeva, O.; Nikitin, S.

2017-12-01

There were events that attracted attention by the grand scale of the glacial catastrophe and its consequences in the North Ossetia (Caucasus Mountains) in 2002. The Kolka Glacier was completely thrown out of its bed and formed a giant water-ice-stone flow, caused destruction and human deaths along the valley of the Genaldon River. The volcanic impact of Mount Kazbek was one of the key factors in this process. The recovery of a new glacier in the empty circus of the Kolka glacier began almost immediately. Currently, three streams of ice have closed in the rear zone of the circus, forming a joint ice massif on the bed. The dimensions of the glacier vary under the influence of both new conditions for the accumulation and melting of ice, and the features of the dynamics of the ice masses filling the vacated bed. This report describes the next stage of the state of the new Kolka glacier - relative stabilization - and analyzes the features of the process of its recovery based on the field observations data, modern space images and the data of changes in summer air temperatures and winter precipitation on the glacier area at the beginning of the 21st century. In recent years, the rate of increase in the area of the glacier does not exceed 0.015 km2 per year. By September 2016, its area reached 1.11 km2, the volume - about 0.044 km3. The conditions for the formation of a new glacier on the empty bottom of the circus differ significantly from the previous ones - when Kolka was restored in after a pulsation on the 1970s. In addition to increase in the summer air temperatures, the thermal balance in the circus has changed due to the increase of the open surface area of the bed and the lateral moraine. At the same time, the growth of the debris cover on the glacier restrains the melting process. Rockfalls and avalanches supply moraine material to the surface of the glacier more intensively than in the 1970s. The conditions of accumulation also changed - the volume of food supplied from the hanging glaciers decreased from the previous 31% to 17%. Fumarolic activity in the crown area of the starboard side of the circus is preserved and this circumstance the restoration of the Kolka glacier.

Optimization of the pyrolysis process of empty fruit bunch (EFB) in a fixed-bed reactor through a central composite design (CCD)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohamed, Alina Rahayu; Hamzah, Zainab; Daud, Mohamed Zulkali Mohamed

2014-07-10

The production of crude palm oil from the processing of palm fresh fruit bunches in the palm oil mills in Malaysia hs resulted in a huge quantity of empty fruit bunch (EFB) accumulated. The EFB was used as a feedstock in the pyrolysis process using a fixed-bed reactor in the present study. The optimization of process parameters such as pyrolysis temperature (factor A), biomass particle size (factor B) and holding time (factor C) were investigated through Central Composite Design (CCD) using Stat-Ease Design Expert software version 7 with bio-oil yield considered as the response. Twenty experimental runs were conducted. Themore » results were completely analyzed by Analysis of Variance (ANOVA). The model was statistically significant. All factors studied were significant with p-values < 0.05. The pyrolysis temperature (factor A) was considered as the most significant parameter because its F-value of 116.29 was the highest. The value of R{sup 2} was 0.9564 which indicated that the selected factors and its levels showed high correlation to the production of bio-oil from EFB pyrolysis process. A quadratic model equation was developed and employed to predict the highest theoretical bio-oil yield. The maximum bio-oil yield of 46.2 % was achieved at pyrolysis temperature of 442.15 °C using the EFB particle size of 866 μm which corresponded to the EFB particle size in the range of 710–1000 μm and holding time of 483 seconds.« less

Coal-Packed Methane Biofilter for Mitigation of Green House Gas Emissions from Coal Mine Ventilation Air

PubMed Central

Limbri, Hendy; Gunawan, Cindy; Thomas, Torsten; Smith, Andrew; Scott, Jason; Rosche, Bettina

2014-01-01

Methane emitted by coal mine ventilation air (MVA) is a significant greenhouse gas. A mitigation strategy is the oxidation of methane to carbon dioxide, which is approximately twenty-one times less effective at global warming than methane on a mass-basis. The low non-combustible methane concentrations at high MVA flow rates call for a catalytic strategy of oxidation. A laboratory-scale coal-packed biofilter was designed and partially removed methane from humidified air at flow rates between 0.2 and 2.4 L min−1 at 30°C with nutrient solution added every three days. Methane oxidation was catalysed by a complex community of naturally-occurring microorganisms, with the most abundant member being identified by 16S rRNA gene sequence as belonging to the methanotrophic genus Methylocystis. Additional inoculation with a laboratory-grown culture of Methylosinus sporium, as investigated in a parallel run, only enhanced methane consumption during the initial 12 weeks. The greatest level of methane removal of 27.2±0.66 g methane m−3 empty bed h−1 was attained for the non-inoculated system, which was equivalent to removing 19.7±2.9% methane from an inlet concentration of 1% v/v at an inlet gas flow rate of 1.6 L min−1 (2.4 min empty bed residence time). These results show that low-cost coal packing holds promising potential as a suitable growth surface and contains methanotrophic microorganisms for the catalytic oxidative removal of methane. PMID:24743729

Optimization of the pyrolysis process of empty fruit bunch (EFB) in a fixed-bed reactor through a central composite design (CCD)

NASA Astrophysics Data System (ADS)

Mohamed, Alina Rahayu; Hamzah, Zainab; Daud, Mohamed Zulkali Mohamed

2014-07-01

The production of crude palm oil from the processing of palm fresh fruit bunches in the palm oil mills in Malaysia hs resulted in a huge quantity of empty fruit bunch (EFB) accumulated. The EFB was used as a feedstock in the pyrolysis process using a fixed-bed reactor in the present study. The optimization of process parameters such as pyrolysis temperature (factor A), biomass particle size (factor B) and holding time (factor C) were investigated through Central Composite Design (CCD) using Stat-Ease Design Expert software version 7 with bio-oil yield considered as the response. Twenty experimental runs were conducted. The results were completely analyzed by Analysis of Variance (ANOVA). The model was statistically significant. All factors studied were significant with p-values < 0.05. The pyrolysis temperature (factor A) was considered as the most significant parameter because its F-value of 116.29 was the highest. The value of R2 was 0.9564 which indicated that the selected factors and its levels showed high correlation to the production of bio-oil from EFB pyrolysis process. A quadratic model equation was developed and employed to predict the highest theoretical bio-oil yield. The maximum bio-oil yield of 46.2 % was achieved at pyrolysis temperature of 442.15 °C using the EFB particle size of 866 μm which corresponded to the EFB particle size in the range of 710-1000 μm and holding time of 483 seconds.

Fluidized-bed combustion reduces atmospheric pollutants

NASA Technical Reports Server (NTRS)

Jonke, A. A.

1972-01-01

Method of reducing sulfur and nitrogen oxides released during combustion of fossil fuels is described. Fuel is burned in fluidized bed of solids with simultaneous feeding of crushed or pulverized limestone to control emission. Process also offers high heat transfer rates and efficient contacting for gas-solid reactions.

Fluidization and drying of biomass particles in a vibrating fluidized bed with pulsed gas flow

DOE PAGES

Jia, Dening; Cathary, Océane; Peng, Jianghong; ...

2015-10-01

Fluidization of biomass particles in the absence of inert bed materials has been tested in a pulsed fluidized bed with vibration, with the pulsation frequency ranging from 033 to 6.67 Hz. Intermittent fluidization at 033 Hz and apparently 'normal' fluidization at 6.67 Hz with regular bubble patterns were observed. Pulsation has proven to be effective in overcoming the bridging of irregular biomass particles induced by strong inter-particle forces. The vibration is only effective when the pulsation is inadequate, either at too low a frequency or too low in amplitude. We dried biomass in order to quantify the effectiveness of gasmore » pulsation for fluidized bed dryers and torrefiers in terms of gas-solid contact efficiency and heat and mass transfer rates. Furthermore, the effects of gas flow rate, bed temperature, pulsation frequency and vibration intensity on drying performance have been systematically investigated. While higher temperature and gas flow rate are favored in drying, there exists an optimal range of pulsation frequency between 0.75 Hz and 1.5 Hz where gas-solid contact is enhanced in both the constant rate drying and falling rate drying periods.« less

Ethylenediamine-N,N′-Disuccinic Acid (EDDS)—Enhanced Flushing Optimization for Contaminated Agricultural Soil Remediation and Assessment of Prospective Cu and Zn Transport

PubMed Central

Ferraro, Alberto; Fabbricino, Massimiliano; La Marca, Agostino; Panico, Antonio; Spasiano, Danilo; Tognacchini, Alice; Pirozzi, Francesco

2018-01-01

This paper presents the results of an experimental study aimed at investigating the effect of operative parameters on the efficiency of a soil flushing process, conducted on real contaminated soil containing high amounts of Cu and Zn. Soil flushing tests were carried out with Ethylenediamine-N,N′-disuccinic acid (EDDS) as a flushing agent due to its high biodegradability and environmentally friendly characteristics. Process parameters such as Empty-Bed Contact Time (EBCT) and EDDS solution molarity were varied from 21–33 h and from 0.36–3.6 mM, respectively. Effects on the mobility of cations such as Fe and Mn were also investigated. Results showed that very high performances can be obtained at [EDDS] = 3.6 mM and EBCT = 33 h. In these conditions, in fact, the amount of removed Cu was 53%, and the amount of removed Zn was 46%. Metal distribution at different depths from the top surface revealed that Cu has higher mobility than Zn. The process results were strongly dependent on the exchange of metals due to the different stability constants of the EDDS complexes. Finally, results from a comparative study showed that soil washing treatment reached the same removal efficiency of the flushing process in a shorter time but required a larger amount of the EDDS solution. PMID:29562649

Ethylenediamine-N,N'-Disuccinic Acid (EDDS)-Enhanced Flushing Optimization for Contaminated Agricultural Soil Remediation and Assessment of Prospective Cu and Zn Transport.

PubMed

Race, Marco; Ferraro, Alberto; Fabbricino, Massimiliano; La Marca, Agostino; Panico, Antonio; Spasiano, Danilo; Tognacchini, Alice; Pirozzi, Francesco

2018-03-18

This paper presents the results of an experimental study aimed at investigating the effect of operative parameters on the efficiency of a soil flushing process, conducted on real contaminated soil containing high amounts of Cu and Zn. Soil flushing tests were carried out with Ethylenediamine- N , N '-disuccinic acid (EDDS) as a flushing agent due to its high biodegradability and environmentally friendly characteristics. Process parameters such as Empty-Bed Contact Time (EBCT) and EDDS solution molarity were varied from 21-33 h and from 0.36-3.6 mM, respectively. Effects on the mobility of cations such as Fe and Mn were also investigated. Results showed that very high performances can be obtained at [EDDS] = 3.6 mM and EBCT = 33 h. In these conditions, in fact, the amount of removed Cu was 53%, and the amount of removed Zn was 46%. Metal distribution at different depths from the top surface revealed that Cu has higher mobility than Zn. The process results were strongly dependent on the exchange of metals due to the different stability constants of the EDDS complexes. Finally, results from a comparative study showed that soil washing treatment reached the same removal efficiency of the flushing process in a shorter time but required a larger amount of the EDDS solution.

Sequential biofiltration - A novel approach for enhanced biological removal of trace organic chemicals from wastewater treatment plant effluent.

PubMed

Müller, Johann; Drewes, Jörg E; Hübner, Uwe

2017-12-15

Recent studies revealed the benefits of oligotrophic and oxic conditions for the biological removal of many trace organic chemicals (TOrCs) during soil-aquifer treatment. These findings indicate an unused tuning potential that might also be applicable in engineered biofiltration systems with drastically reduced hydraulic retention times for an enhanced mitigation of TOrCs during wastewater treatment. This study introduces the novel approach of sequential biofiltration (SBF) for the advanced treatment of secondary effluent using two granular media filters operated in series with an intermediate aeration step aiming for oxic and oligotrophic conditions in the second filter stage. Results from the experiments conducted at pilot-scale confirm a reduced substrate availability and predominantly oxic conditions in the second filter stage of the SBF setup. An increased removal of several TOrCs was observed in an SBF system as compared to a conventional single-stage biofiltration unit operated at the same overall empty bed contact time (EBCT). Short-term tests with varying EBCTs in the first filter stage revealed a high degree of system robustness of TOrC mitigation when confronted with sudden hydraulic load variations. Higher removal of several TOrCs at increased EBCTs in the second filter stage indicates that EBCT might play a crucial role for the degradation of certain compounds. Copyright © 2017 Elsevier Ltd. All rights reserved.

Adsorption of selected pharmaceuticals and an endocrine disrupting compound by granular activated carbon. 2. Model prediction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Z.; Peldszus, S.; Huck, P.M.

The adsorption of two representative pharmaceutically active compounds (PhACs) naproxen and carbamazepine and one endocrine disrupting compound (EDC) nonylphenol was studied in pilot-scale granular activated carbon (GAC) adsorbers using post-sedimentation (PS) water from a full-scale drinking water treatment plant. The GAC adsorbents were coal-based Calgon Filtrasorb 400 and coconut shell-based PICA CTIF TE. Acidic naproxen broke through fastest while nonylphenol was removed best, which was consistent with the degree to which fouling affected compound removals. Model predictions and experimental data were generally in good agreement for all three compounds, which demonstrated the effectiveness and robustness of the pore and surfacemore » diffusion model (PSDM) used in combination with the time-variable parameter approach for predicting removals at environmentally relevant concentrations (i.e., ng/L range). Sensitivity analyses suggested that accurate determination of film diffusion coefficients was critical for predicting breakthrough for naproxen and carbamazepine, in particular when high removals are targeted. Model simulations demonstrated that GAC carbon usage rates (CURs) for naproxen were substantially influenced by the empty bed contact time (EBCT) at the investigated conditions. Model-based comparisons between GAC CURs and minimum CURs for powdered activated carbon (PAC) applications suggested that PAC would be most appropriate for achieving 90% removal of naproxen, whereas GAC would be more suitable for nonylphenol. 25 refs., 4 figs., 1 tab.« less

Understanding the fate of organic micropollutants in sand and granular activated carbon biofiltration systems.

PubMed

Paredes, L; Fernandez-Fontaina, E; Lema, J M; Omil, F; Carballa, M

2016-05-01

In this study, sand and granular activated carbon (GAC) biofilters were comparatively assessed as post-treatment technologies of secondary effluents, including the fate of 18 organic micropollutants (OMPs). To determine the contribution of adsorption and biotransformation in OMP removal, four reactors were operated (two biofilters (with biological activity) and two filters (without biological activity)). In addition, the influence of empty bed contact time (EBCT), ranging from 0.012 to 3.2d, and type of secondary effluent (anaerobic and aerobic) were evaluated. Organic matter, ammonium and nitrate were removed in both biofilters, being their adsorption higher on GAC than on sand. According to the behaviour exhibited, OMPs were classified in three different categories: I) biotransformation and high adsorption on GAC and sand (galaxolide, tonalide, celestolide and triclosan), II) biotransformation, high adsorption on GAC but low or null adsorption on sand (ibuprofen, naproxen, fluoxetine, erythromycin, roxythromycim, sulfamethoxazole, trimethoprim, bisphenol A, estrone, 17β-estradiol and 17α-ethinylestradiol), and, III) only adsorption on GAC (carbamazepine, diazepam and diclofenac). No influence of EBCT (in the range tested) and type of secondary effluent was observed in GAC reactors, whereas saturation and kinetic limitation of biotransformation were observed in sand reactors. Taking into account that most of the organic micropollutants studied (around 60%) fell into category II, biotransformation is crucial for the elimination of OMPs in sand biofilters. Copyright © 2016 Elsevier B.V. All rights reserved.

Ulcerative colitis: ultrastructure of interstitial cells in myenteric plexus.

PubMed

Rumessen, J J; Vanderwinden, J-M; Horn, T

2010-10-01

Interstitial cells of Cajal (ICC) are key regulatory cells in the gut. In the colon of patients with severe ulcerative colitis (UC), myenteric ICC had myoid ultrastructural features and were in close contact with nerve terminals. In all patients as opposed to controls, some ICC profiles showed degenerative changes, such as lipid droplets and irregular vacuoles. Nerve terminals often appeared swollen and empty. Glial cells, muscle cells, and fibroblast-like cells (FLC) showed no alterations. FLC enclosed macrophages (MLC), which were in close contact with naked axon terminals. The organization and cytological changes may be of pathophysiological significance in patients with UC.

Exposure of bed bugs to metarhizium anisopliae, and the effect of defensive secretions on fungal growth in vitro

USDA-ARS?s Scientific Manuscript database

Bed bugs Cimex lectularius were treated with conidia of the entomopathogenic fungus Metarhizium anisopliae by topical, spray, and contact exposure. One week post-exposure, inconsistent mortalities were observed, averaging 30% across all treatment groups and replicates. Microscopic examination of top...

Reported bed net ownership and use in social contacts is associated with uptake of bed nets for malaria prevention in pregnant women in Ghana.

PubMed

Ernst, Kacey C; Erly, Steven; Adusei, Charity; Bell, Melanie L; Kessie, David Komla; Biritwum-Nyarko, Alberta; Ehiri, John

2017-01-04

Despite progress made in the last decades, malaria persists as a pressing health issue in sub-Saharan Africa. Pregnant women are particularly vulnerable to infection and serious health outcomes for themselves and their unborn child. Risk can be mitigated through appropriate use of control measures such as insecticide-treated bed nets. Although social networks can influence uptake of preventive strategies, the role of social influence on bed net ownership has not been explored. During an evaluation of a bed net distribution programme, the influence of non-health care advisors on ownership and use of bed nets by pregnant women in Kumasi, Ghana was examined. Data were collected through in-person interviews with 300 pregnant women seeking antenatal care in an urban hospital in Kumasi, Ghana. Participants were asked about their bed net ownership, bed net use, and information about three personal contacts that they go to for pregnancy advice. Information about these advisors was combined into an influence score. Logistic regression models were used to determine the association between the score and bed net ownership. Those who owned a bed net were further assessed to determine if interpersonal influence was associated with self-reported sleeping under the bed net the previous night. Of the 294 women in the analysis, 229 (78%) reported owning bed nets. Of these bed net owners, 139 (61%) reported using a bed net the previous night. A dose response relationship was observed between the interpersonal influence score and bed net ownership and use. Compared to the lowest influence score, those with the highest influence score (>1 SD above the mean) were marginally more likely to own a bed net [OR = 2.37, 95% CI (0.87, 6.39)] and much more likely to use their bed net [5.38, 95% CI (1.89, 15.25)] after adjusting for other factors. Interpersonal influence appears to have modest impact on ownership and use of bed nets by pregnant women in an urban area of Ghana. Further investigations would need to be conducted to determine if the relationship is causal or if individuals who associate are simply more likely to have similar practices.

The effect of nitrate on ethylene biofiltration.

PubMed

Lee, Sang-Hun; Li, Congna; Heber, Albert J

2012-11-30

This study investigated the effects of filter media types and nitrate (NO(3)(-)) concentrations in nutrient solutions on C(2)H(4) biofiltration. A new nutrient solution with zero NO(3)(-) concentration was supplied to two perlite-bed biotrickling filters, two perlite-bed biofilters, and two GAC (Granular Activated Carbon)-bed biofilters, while the other with 2 g L(-1) of NO(3)(-) was used for the other two GAC biofilters. All reactors underwent a total test duration of over 175 days with an EBRT (Empty Bed Residence Time) of 30 s, inlet gas flow rate of 7 L min(-1), and inlet C(2)H(4) concentrations of 20-30 mg m(-3). NO(3)(-) concentration and media type significantly affected the C(2)H(4) removal efficiencies in all types of biofiltration. The perlite media with no NO(3)(-) achieved C(2)H(4) removal efficiencies 10-50% higher than the others. A NO(3)(-) concentration as high as 2 g L(-1) in the original nutrient solution may act as an inhibitor that suppresses the growth or activity of C(2)H(4) degraders. In addition, the perlite media resulted in higher C(2)H(4) removal efficiencies than GAC media, because the hydrophilic surface of the perlite leads to a higher moisture content and thus to favorable microbial growth. Copyright © 2012 Elsevier B.V. All rights reserved.

The Devil is in the Details: Using X-Ray Computed Tomography to Develop Accurate 3D Grain Characteristics and Bed Structure Metrics for Gravel Bed Rivers

NASA Astrophysics Data System (ADS)

Voepel, H.; Hodge, R. A.; Leyland, J.; Sear, D. A.; Ahmed, S. I.

2014-12-01

Uncertainty for bedload estimates in gravel bed rivers is largely driven by our inability to characterize the arrangement and orientation of the sediment grains within the bed. The characteristics of the surface structure are produced by the water working of grains, which leads to structural differences in bedforms through differential patterns of grain sorting, packing, imbrication, mortaring and degree of bed armoring. Until recently the technical and logistical difficulties of characterizing the arrangement of sediment in 3D have prohibited a full understanding of how grains interact with stream flow and the feedback mechanisms that exist. Micro-focus X-ray CT has been used for non-destructive 3D imaging of grains within a series of intact sections of river bed taken from key morphological units (see Figure 1). Volume, center of mass, points of contact, protrusion and spatial orientation of individual surface grains are derived from these 3D images, which in turn, facilitates estimates of 3D static force properties at the grain-scale such as pivoting angles, buoyancy and gravity forces, and grain exposure. By aggregating representative samples of grain-scale properties of localized interacting sediment into overall metrics, we can compare and contrast bed stability at a macro-scale with respect to stream bed morphology. Understanding differences in bed stability through representative metrics derived at the grain-scale will ultimately lead to improved bedload estimates with reduced uncertainty and increased understanding of interactions between grain-scale properties on channel morphology. Figure 1. CT-Scans of a water worked gravel-filled pot. a. 3D rendered scan showing the outer mesh, and b. the same pot with the mesh removed. c. vertical change in porosity of the gravels sampled in 5mm volumes. Values are typical of those measured in the field and lab. d. 2-D slices through the gravels at 20% depth from surface (porosity = 0.35), and e. 75% depth from surface (porosity = 0.24), showing the presence of fine sediments 'mortaring' the larger gravels. f. shows a longitudinal slide from which pivot angle measurements can be determined for contact points between particles. g. Example of two particle extraction from the CT scan showing how particle contact areas can be measured (dark area).

History of the 4th Battalion, 37th Armored Regiment in Operation Desert Shield/Storm. Volume 2

DTIC Science & Technology

1992-04-15

model white Toyota truck pulled into the LOGPAC area. An Arab jumped out of the driver’s side of the vehicle and grabbed a five gallon can out of the...truck bed. He looked at SGT Stephen I. Lee, the D Co supply sergeant, and asked, "Gauss? Gauss?" The Toyota truck was parked one hundred meters away...from the Toyota truck and began to happily roll an empty fifty-five gallon drum off the truck. Seeing as how I did not suffer from the same hearing

Bed bug aggregation pheromone finally identified.

PubMed

Gries, Regine; Britton, Robert; Holmes, Michael; Zhai, Huimin; Draper, Jason; Gries, Gerhard

2015-01-19

Bed bugs have become a global epidemic and current detection tools are poorly suited for routine surveillance. Despite intense research on bed bug aggregation behavior and the aggregation pheromone, which could be used as a chemical lure, the complete composition of this pheromone has thus far proven elusive. Here, we report that the bed bug aggregation pheromone comprises five volatile components (dimethyl disulfide, dimethyl trisulfide, (E)-2-hexenal, (E)-2-octenal, 2-hexanone), which attract bed bugs to safe shelters, and one less-volatile component (histamine), which causes their arrestment upon contact. In infested premises, a blend of all six components is highly effective at luring bed bugs into traps. The trapping of juvenile and adult bed bugs, with or without recent blood meals, provides strong evidence that this unique pheromone bait could become an effective and inexpensive tool for bed bug detection and potentially their control. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fluidized-bed catalytic coal-gasification process. [US patent; pretreatment to minimize agglomeration

DOEpatents

Euker, C.A. Jr.; Wesselhoft, R.D.; Dunkleman, J.J.; Aquino, D.C.; Gouker, T.R.

1981-09-14

Coal or similar carbonaceous solids impregnated with gasification catalyst constituents are oxidized by contact with a gas containing between 2 vol % and 21 vol % oxygen at a temperature between 50 and 250/sup 0/C in an oxidation zone and the resultant oxidized, catalyst impregnated solids are then gasified in a fluidized bed gasification zone at an elevated pressure. The oxidation of the catalyst impregnated solids under these conditions insures that the bed density in the fluidized bed gasification zone will be relatively high even though the solids are gasified at elevated pressure and temperature.

A collision model for grain-resolving simulations of flows over dense, mobile, polydisperse granular sediment beds

DOE PAGES

Biegert, Edward; Vowinckel, Bernhard; Meiburg, Eckart

2017-03-21

We present a collision model for phase-resolved Direct Numerical Simulations of sediment transport that couple the fluid and particles by the Immersed Boundary Method. Typically, a contact model for these types of simulations comprises a lubrication force for particles in close proximity to another solid object, a normal contact force to prevent particles from overlapping, and a tangential contact force to account for friction. Our model extends the work of previous authors to improve upon the time integration scheme to obtain consistent results for particle-wall collisions. Furthermore, we account for polydisperse spherical particles and introduce new criteria to account formore » enduring contact, which occurs in many sediment transport situations. This is done without using arbitrary values for physically-defined parameters and by maintaining the full momentum balance of a particle in enduring contact. Lastly, we validate our model against several test cases for binary particle-wall collisions as well as the collective motion of a sediment bed sheared by a viscous flow, yielding satisfactory agreement with experimental data by various authors.« less

A collision model for grain-resolving simulations of flows over dense, mobile, polydisperse granular sediment beds

NASA Astrophysics Data System (ADS)

Biegert, Edward; Vowinckel, Bernhard; Meiburg, Eckart

2017-07-01

We present a collision model for phase-resolved Direct Numerical Simulations of sediment transport that couple the fluid and particles by the Immersed Boundary Method. Typically, a contact model for these types of simulations comprises a lubrication force for particles in close proximity to another solid object, a normal contact force to prevent particles from overlapping, and a tangential contact force to account for friction. Our model extends the work of previous authors to improve upon the time integration scheme to obtain consistent results for particle-wall collisions. Furthermore, we account for polydisperse spherical particles and introduce new criteria to account for enduring contact, which occurs in many sediment transport situations. This is done without using arbitrary values for physically-defined parameters and by maintaining the full momentum balance of a particle in enduring contact. We validate our model against several test cases for binary particle-wall collisions as well as the collective motion of a sediment bed sheared by a viscous flow, yielding satisfactory agreement with experimental data by various authors.

Computational domain discretization in numerical analysis of flow within granular materials

NASA Astrophysics Data System (ADS)

Sosnowski, Marcin

2018-06-01

The discretization of computational domain is a crucial step in Computational Fluid Dynamics (CFD) because it influences not only the numerical stability of the analysed model but also the agreement of obtained results and real data. Modelling flow in packed beds of granular materials is a very challenging task in terms of discretization due to the existence of narrow spaces between spherical granules contacting tangentially in a single point. Standard approach to this issue results in a low quality mesh and unreliable results in consequence. Therefore the common method is to reduce the diameter of the modelled granules in order to eliminate the single-point contact between the individual granules. The drawback of such method is the adulteration of flow and contact heat resistance among others. Therefore an innovative method is proposed in the paper: single-point contact is extended to a cylinder-shaped volume contact. Such approach eliminates the low quality mesh elements and simultaneously introduces only slight distortion to the flow as well as contact heat transfer. The performed analysis of numerous test cases prove the great potential of the proposed method of meshing the packed beds of granular materials.

Removal of fluoride impurities from UF/sub 6/ gas

DOEpatents

Beitz, J.V.

1984-01-06

A method of purifying a UF/sub 6/ gas stream containing one or more metal fluoride impurities composed of a transuranic metal, transition metal or mixtures thereof, is carried out by contacting the gas stream with a bed of UF/sub 5/ in a reaction vessel under conditions where at least one impurity reacts with the UF/sub 5/ to form a nongaseous product and a treated gas stream, and removing the treated gas stream from contact with the bed. The nongaseous products are subsequently removed in a reaction with an active fluorine affording agent to form a gaseous impurity which is removed from the reaction vessel. The bed of UF/sub 5/ is formed by the reduction of UF/sub 6/ in the presence of uv light. One embodiment of the reaction vessel includes a plurality of uv light sources as tubes on which UF/sub 5/ is formed. 2 figures.

Removal of fluoride impurities from UF.sub.6 gas

DOEpatents

Beitz, James V.

1985-01-01

A method of purifying a UF.sub.6 gas stream containing one or more metal fluoride impurities composed of a transuranic metal, transition metal or mixtures thereof, is carried out by contacting the gas stream with a bed of UF.sub.5 in a reaction vessel under conditions where at least one impurity reacts with the UF.sub.5 to form a nongaseous product and a treated gas stream, and removing the treated gas stream from contact with the bed. The nongaseous products are subsequently removed in a reaction with an active fluorine affording agent to form a gaseous impurity which is removed from the reaction vessel. The bed of UF.sub.5 is formed by the reduction of UF.sub.6 in the presence of UV light. One embodiment of the reaction vessel includes a plurality of UV light sources as tubes on which UF.sub.5 is formed.

Predicted sedimentary record of reflected bores

USGS Publications Warehouse

Higman, B.; Gelfenbaum, G.; Lynett, P.; Moore, A.; Jaffe, B.

2007-01-01

Where a steep slope blocks an inrushing tsunami, the tsunami commonly reverses direction as a reflected bore. A simple method for relating vertical and horizontal variation in sediment size to output from numerical models of depth-averaged tsunami flow yields predictions about the sedimentary record of reflected bores: 1. Near the reflector, a abrupt slowing of the flow as the reflected bore passes is recorded by a normally graded layer that drapes preexisting topography. 2. At intermediate distances from the reflector, the deposit consists of a single normally graded bed deposited preferentially in depressions, possibly including a sharp fine-over-coarse contact. This contact records a brief period of erosion as the front of the reflected bore passes. 3. Far seaward of the reflector, grading in the deposit includes two distinct normally graded beds deposited preferentially in depressions separated by an erosional unconformity. The second normally graded bed records the reflected bore.

Horizontal Transfer of Diatomaceous Earth and Botanical Insecticides in the Common Bed Bug, Cimex lectularius L.; Hemiptera: Cimicidae

PubMed Central

Akhtar, Yasmin; Isman, Murray B.

2013-01-01

Background Horizontal transfer of insecticide occurs when insects contact or ingest an insecticide, return to an aggregation or a nest, and transfer the insecticide to other conspecific insects through contact. This phenomenon has been reported in a number of insects including social insects, however it has not been reported in bed bugs. Since horizontal transfer can facilitate the spread of insecticide into hard to reach spaces, it could contribute greatly to the management of these public health pests. Methodology/Results To demonstrate horizontal transfer of diatomaceous earth and botanical insecticides in C. lectularius, an exposed (donor) bed bug, following a 10-minute acquisition period, was placed with unexposed (recipient) bed bugs. Mortality data clearly demonstrates that diatomaceous earth (DE 51) was actively transferred from a single exposed bug to unexposed bugs in a concentration dependent manner. LC50 values varied from 24.4 mg at 48 h to 5.1 mg at 216 h when a single exposed bed bug was placed with 5 unexposed bed bugs. LT50 values also exhibited a concentration response. LT50 values varied from 1.8 days to 8.4 days when a ‘donor’ bug exposed to 20 and 5 mg of dust respectively was placed with 5 ‘recipient’ bugs. Dust was also actively transferred from adult bed bugs to the nymphs. In addition we observed horizontal transfer of botanical insecticides including neem, ryania, and rotenone to varying degrees. Conclusion/Significance Our data clearly demonstrate horizontal transfer of diatomaceous earth and botanical insecticides in the common bed bug, C. lectularius. Use of a fluorescent dust provided visual confirmation that contaminated bed bugs transfer dust to untreated bed bugs in harborage. This result is important because bedbugs live in hard-to-reach places and interaction between conspecifics can be exploited for delivery and dissemination of management products directed at this public health pest. PMID:24086593

Horizontal transfer of diatomaceous earth and botanical insecticides in the common bed bug, Cimex lectularius L.; hemiptera: cimicidae.

PubMed

Akhtar, Yasmin; Isman, Murray B

2013-01-01

Horizontal transfer of insecticide occurs when insects contact or ingest an insecticide, return to an aggregation or a nest, and transfer the insecticide to other conspecific insects through contact. This phenomenon has been reported in a number of insects including social insects, however it has not been reported in bed bugs. Since horizontal transfer can facilitate the spread of insecticide into hard to reach spaces, it could contribute greatly to the management of these public health pests. To demonstrate horizontal transfer of diatomaceous earth and botanical insecticides in C. lectularius, an exposed (donor) bed bug, following a 10-minute acquisition period, was placed with unexposed (recipient) bed bugs. Mortality data clearly demonstrates that diatomaceous earth (DE 51) was actively transferred from a single exposed bug to unexposed bugs in a concentration dependent manner. LC50 values varied from 24.4 mg at 48 h to 5.1 mg at 216 h when a single exposed bed bug was placed with 5 unexposed bed bugs. LT50 values also exhibited a concentration response. LT50 values varied from 1.8 days to 8.4 days when a 'donor' bug exposed to 20 and 5 mg of dust respectively was placed with 5 'recipient' bugs. Dust was also actively transferred from adult bed bugs to the nymphs. In addition we observed horizontal transfer of botanical insecticides including neem, ryania, and rotenone to varying degrees. Our data clearly demonstrate horizontal transfer of diatomaceous earth and botanical insecticides in the common bed bug, C. lectularius. Use of a fluorescent dust provided visual confirmation that contaminated bed bugs transfer dust to untreated bed bugs in harborage. This result is important because bedbugs live in hard-to-reach places and interaction between conspecifics can be exploited for delivery and dissemination of management products directed at this public health pest.

Feed gas contaminant removal in ion transport membrane systems

DOEpatents

Carolan, Michael Francis [Allentown, PA; Miller, Christopher Francis [Macungie, PA

2008-09-16

Method for gas purification comprising (a) obtaining a feed gas stream containing one or more contaminants selected from the group consisting of volatile metal oxy-hydroxides, volatile metal oxides, and volatile silicon hydroxide; (b) contacting the feed gas stream with a reactive solid material in a guard bed and reacting at least a portion of the contaminants with the reactive solid material to form a solid reaction product in the guard bed; and (c) withdrawing from the guard bed a purified gas stream.

Biofiltration of methane using hybrid mixtures of biochar, lava rock and compost.

PubMed

La, Helen; Hettiaratchi, J Patrick A; Achari, Gopal; Verbeke, Tobin J; Dunfield, Peter F

2018-05-21

Using hybrid packing materials in biofiltration systems takes advantage of both the inorganic and organic properties offered by the medium including structural stability and a source of available nutrients, respectively. In this study, hybrid mixtures of compost with either lava rock or biochar in four different mixture ratios were compared against 100% compost in a methane biofilter with active aeration at two ports along the height of the biofilter. Biochar outperformed lava rock as a packing material by providing the added benefit of participating in sorption reactions with CH 4 . This study provides evidence that a 7:1 volumetric mixture of biochar and compost can successfully remove up to 877 g CH 4 /m 3 ·d with empty-bed residence times of 82.8 min. Low-affinity methanotrophs were responsible for the CH 4 removal in these systems (K M(app) ranging from 5.7 to 42.7 µM CH 4 ). Sequencing of 16S rRNA gene amplicons indicated that Gammaproteobacteria methanotrophs, especially members of the genus Methylobacter, were responsible for most of the CH 4 removal. However, as the compost medium was replaced with more inert medium, there was a decline in CH 4 removal efficiency coinciding with an increased dominance of Alphaproteobacteria methanotrophs like Methylocystis and Methylocella. As a biologically-active material, compost served as the sole source of nutrients and inoculum for the biofilters which greatly simplified the operation of the system. Higher elimination capacities may be possible with higher compost content such as a 1:1 ratio of either biochar or lava rock, while maintaining the empty-bed residence time at 82.8 min. Copyright © 2018 Elsevier Ltd. All rights reserved.

Experimental Study and Computational Simulations of Key Pebble Bed Thermo-mechanics Issues for Design and Safety

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tokuhiro, Akira; Potirniche, Gabriel; Cogliati, Joshua

2014-07-08

An experimental and computational study, consisting of modeling and simulation (M&S), of key thermal-mechanical issues affecting the design and safety of pebble-bed (PB) reactors was conducted. The objective was to broaden understanding and experimentally validate thermal-mechanic phenomena of nuclear grade graphite, specifically, spheres in frictional contact as anticipated in the bed under reactor relevant pressures and temperatures. The contact generates graphite dust particulates that can subsequently be transported into the flowing gaseous coolent. Under postulated depressurization transients and with the potential for leaked fission products to be adsorbed onto graphite 'dust', there is the potential for fission products to escapemore » from the primary volume. This is a design safety concern. Furthermore, earlier safety assessment identified the distinct possibility for the dispersed dust to combust in contact with air if sufficient conditions are met. Both of these phenomena were noted as important to design review and containing uncertainty to warrant study. The team designed and conducted two separate effects tests to study and benchmark the potential dust-generation rate, as well as study the conditions under which a dust explosion may occure in a standardized, instrumented explosion chamber.« less

Physical and Chemical Interactions with Conspecifics Mediate Sex Change in a Protandrous Gastropod Crepidula fornicata.

PubMed

Cahill, Abigail E; Juman, Alia Rehana; Pellman-Isaacs, Aaron; Bruno, William T

2015-12-01

The protandrous marine snail Crepidula fornicata has been a theoretical and empirical model for studies of sex change for many decades. We investigated the social conditions under which sex change occurs in this species by manipulating physical and chemical contact with conspecifics. Male snails were either in physical and chemical contact with females or in chemical contact with, but physically isolated from, females. Males were tested both with living females and with empty, sterilized shells. Males that were physically touching a living female were less likely to change sex than the isolated controls, while males in chemical (but not physical) contact with females changed sex no slower than the isolated controls. These results provide experimental evidence that the factor controlling sex change in C. fornicata is due to a contact-borne inhibitor associated with female conspecifics. These findings serve as a basis for future studies of sex change in this model system. © 2015 Marine Biological Laboratory.

Fluidized bed combustor modeling

NASA Technical Reports Server (NTRS)

Horio, M.; Rengarajan, P.; Krishnan, R.; Wen, C. Y.

1977-01-01

A general mathematical model for the prediction of performance of a fluidized bed coal combustor (FBC) is developed. The basic elements of the model consist of: (1) hydrodynamics of gas and solids in the combustor; (2) description of gas and solids contacting pattern; (3) kinetics of combustion; and (4) absorption of SO2 by limestone in the bed. The model is capable of calculating the combustion efficiency, axial bed temperature profile, carbon hold-up in the bed, oxygen and SO2 concentrations in the bubble and emulsion phases, sulfur retention efficiency and particulate carry over by elutriation. The effects of bed geometry, excess air, location of heat transfer coils in the bed, calcium to sulfur ratio in the feeds, etc. are examined. The calculated results are compared with experimental data. Agreement between the calculated results and the observed data are satisfactory in most cases. Recommendations to enhance the accuracy of prediction of the model are suggested.

Pyrolysis of Date palm waste in a fixed-bed reactor: Characterization of pyrolytic products.

PubMed

Bensidhom, Gmar; Ben Hassen-Trabelsi, Aïda; Alper, Koray; Sghairoun, Maher; Zaafouri, Kaouther; Trabelsi, Ismail

2018-01-01

The pyrolysis of several Tunisian Date Palm Wastes (DPW): Date Palm Rachis (DPR), Date Palm Leaflets (DPL), Empty Fruit Bunches (EFB) and Date Palm Glaich (DPG) was run using a fixed-bed reactor, from room temperature to 500°C, with 15°C/min as heating rate and -5°C as condensation temperature, in order to produce bio-oil, biochar and syngas. In these conditions, the bio-oil yield ranges from 17.03wt% for DPL to 25.99wt% for EFB. For the biochar, the highest yield (36.66wt%) was obtained for DPL and the lowest one (31.66wt%) was obtained from DPG while the syngas production varies from 39.10wt% for DPR to 46.31wt% DPL. The raw material and pyrolysis products have been characterized using elemental analysis thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM). The syngas composition has been characterized using gas analyzer. Copyright © 2017 Elsevier Ltd. All rights reserved.

Updated tops file for Cretaceous and lower Tertiary units, Piceance Basin, northwest Colorado

USGS Publications Warehouse

Johnson, Ronald C.; Dietrich, John D.; Mercier, Tracey J.

2015-08-04

Each entry for the base of the Long Point Bed was obtained at a location where the mapped Long Point Bed intersects a contour line on the published maps. Precision of each elevation is therefore dependent on the precision of the maps and the placement of the mapped contact by the authors.

Regional Disease Vector Ecology Profile: The Koreas

DTIC Science & Technology

2015-01-01

Lymantriidae): The larvae, pupae and adults of E. flava are covered with hairs that cause dermatitis (papulourticarial reaction) when they contact ...Information Services Division at (301) 295-8310/7476, DSN 295- 8310/7476 or the AFPMB Webmaster, http://www.afpmb.org/ contact . Current Information: Current...timely manner. For insect repellents, pesticides, pesticide application equipment, PPMs (bed nets, head nets, etc.) and respirators contact the DLA

Moving bed reactor setup to study complex gas-solid reactions.

PubMed

Gupta, Puneet; Velazquez-Vargas, Luis G; Valentine, Charles; Fan, Liang-Shih

2007-08-01

A moving bed scale reactor setup for studying complex gas-solid reactions has been designed in order to obtain kinetic data for scale-up purpose. In this bench scale reactor setup, gas and solid reactants can be contacted in a cocurrent and countercurrent manner at high temperatures. Gas and solid sampling can be performed through the reactor bed with their composition profiles determined at steady state. The reactor setup can be used to evaluate and corroborate model parameters accounting for intrinsic reaction rates in both simple and complex gas-solid reaction systems. The moving bed design allows experimentation over a variety of gas and solid compositions in a single experiment unlike differential bed reactors where the gas composition is usually fixed. The data obtained from the reactor can also be used for direct scale-up of designs for moving bed reactors.

Solar heated fluidized bed gasification system

NASA Technical Reports Server (NTRS)

Qader, S. A. (Inventor)

1981-01-01

A solar-powered fluidized bed gasification system for gasifying carbonaceous material is presented. The system includes a solar gasifier which is heated by fluidizing gas and steam. Energy to heat the gas and steam is supplied by a high heat capacity refractory honeycomb which surrounds the fluid bed reactor zone. The high heat capacity refractory honeycomb is heated by solar energy focused on the honeycomb by solar concentrator through solar window. The fluid bed reaction zone is also heated directly and uniformly by thermal contact of the high heat capacity ceramic honeycomb with the walls of the fluidized bed reactor. Provisions are also made for recovering and recycling catalysts used in the gasification process. Back-up furnace is provided for start-up procedures and for supplying heat to the fluid bed reaction zone when adequate supplies of solar energy are not available.

Oral and intravenous l-[1-13 C]phenylalanine delivery measure similar rates of elimination when gastric emptying and splanchnic extraction are accounted for in adult mixed hounds.

PubMed

Gooding, M A; Cant, J P; Pencharz, P B; Davenport, G M; Atkinson, J L; Shoveller, A K

2013-02-01

There are few reported estimates of amino acid (AA) kinetics in adult mammals and none exist in adult dogs. The study objectives were to evaluate the use of oral isotope delivery in contrast to the more commonly used intravenous (IV) delivery to estimate AA kinetics in adult dogs and to estimate splanchnic extraction and gastric emptying using a commonly accepted mathematical model. Dogs received 25 × 1/2-hourly meals (13 g/kg BW/day) and either an oral or IV bolus of l-[1-(13) C]Phe (12 mg/kg BW). Blood samples were taken immediately before each feeding. Concentrations of plasma Phe were measured using liquid chromatography-tandem mass spectrometry. There were no differences in baseline plasma Phe concentrations (34 μm ± 0.61), Phe distribution volume, Phe pool size and rate constants between dogs when the tracer was administered IV or orally (p > 0.25). Decay curve for plasma l-[1-(13) C]Phe differed between IV and oral dosing protocols with IV dosing fit best using a two-compartment model. Phe disappeared from plasma at a mean rate of 2.8%/min. Estimates of gastric emptying and splanchnic extraction did not differ based on oral or IV tracer dosing when the decay curves were fit with the two-compartment model (p > 0.40). The half-life for gastric emptying was 18 min, and first-pass Phe extraction by the splanchnic bed was 24% of the dietary Phe. These results suggest that oral isotope dosing can be used as an alternative to IV isotope dosing in studies that utilize a primed, constant dosing approach to measure protein and amino acid kinetics. © 2011 Blackwell Verlag GmbH.

Biodegradation of toluene vapor in coir based upflow packed bed reactor by Trichoderma asperellum isolate.

PubMed

Gopinath, M; Mohanapriya, C; Sivakumar, K; Baskar, G; Muthukumaran, C; Dhanasekar, R

2016-03-01

In the present study, a new biofiltration system involving a selective microbial strain isolated from aerated municipal sewage water attached with coir as packing material was developed for toluene degradation. The selected fungal isolate was identified as Trichoderma asperellum by 16S ribosomal RNA (16S rRNA) sequencing method, and pylogenetic tree was constructed using BLASTn search. Effect of various factors on growth and toluene degradation by newly isolated T. asperellum was studied in batch studies, and the optimum conditions were found to be pH 7.0, temperature 30 °C, and initial toluene concentration 1.5 (v/v)%. Continuous removal of gaseous toluene was monitored in upflow packed bed reactor (UFPBR) using T. asperellum. Effect of various parameters like column height, flow rate, and the inlet toluene concentration were studied to evaluate the performance of the biofilter. The maximum elimination capacity (257 g m(-3) h(-1)) was obtained with the packing height of 100 cm with the empty bed residence time of 5 min. Under these optimum conditions, the T. asperellum showed better toluene removal efficiency. Kinetic models have been developed for toluene degradation by T. asperellum using macrokinetic approach of the plug flow model incorporated with Monod model.

Environmental Inventory: Little South Fork Cumberland River.

DTIC Science & Technology

1981-11-01

coal and clay shale. The contact between the Mississippian strata (Pennington Formation ) and...these formations include the Barren Fork coal bed and the Stearns coal zone. In addition to these there are several unnamed coal beds. Number and...Cindy Cliff, Coal Cliff, Sand Cliff and Balls Cliff are being mined by the Greenwood Land and Mining Company of Somerset and Parkers Lake, Kentucky

Methods and apparatus for using gas and liquid phase cathodic depolarizers

NASA Technical Reports Server (NTRS)

Murphy, Oliver J. (Inventor); Hitchens, G. Duncan (Inventor)

1998-01-01

The invention provides methods for using gas and liquid phase cathodic depolarizers in an electrochemical cell having a cation exchange membrane in intimate contact with the anode and cathode. The electrochemical conversion of cathodic depolarizers at the cathode lowers the cell potential necessary to achieve a desired electrochemical conversion, such as ozone evolution, at the anode. When gaseous cathodic depolarizers, such as oxygen, are used, a gas diffusion cathode having the cation exchange membrane bonded thereto is preferred. When liquid phase cathodic depolarizers are used, the cathode may be a flow-by electrode, flow-through electrode, packed-bed electrode or a fluidized-bed electrode in intimate contact with the cation exchange membrane.

Efficient peroxydisulfate activation process not relying on sulfate radical generation for water pollutant degradation.

PubMed

Zhang, Tao; Chen, Yin; Wang, Yuru; Le Roux, Julien; Yang, Yang; Croué, Jean-Philippe

2014-05-20

Peroxydisulfate (PDS) is an appealing oxidant for contaminated groundwater and toxic industrial wastewaters. Activation of PDS is necessary for application because of its low reactivity. Present activation processes always generate sulfate radicals as actual oxidants which unselectively oxidize organics and halide anions reducing oxidation capacity of PDS and producing toxic halogenated products. Here we report that copper oxide (CuO) can efficiently activate PDS under mild conditions without producing sulfate radicals. The PDS/CuO coupled process is most efficient at neutral pH for decomposing a model compound, 2,4-dichlorophenol (2,4-DCP). In a continuous-flow reaction with an empty-bed contact time of 0.55 min, over 90% of 2,4-DCP (initially 20 μM) and 90% of adsorbable organic chlorine (AOCl) can be removed at the PDS/2,4-DCP molar ratio of 1 and 4, respectively. Based on kinetic study and surface characterization, PDS is proposed to be first activated by CuO through outer-sphere interaction, the rate-limiting step, followed by a rapid reaction with 2,4-DCP present in the solution. In the presence of ubiquitous chloride ions in groundwater/industrial wastewater, the PDS/CuO oxidation shows significant advantages over sulfate radical oxidation by achieving much higher 2,4-DCP degradation capacity and avoiding the formation of highly chlorinated degradation products. This work provides a new way of PDS activation for contaminant removal.

Use of ozone-biofiltration for bulk organic removal and disinfection byproduct mitigation in potable reuse applications.

PubMed

Arnold, Mayara; Batista, Jacimaria; Dickenson, Eric; Gerrity, Daniel

2018-07-01

The purpose of this research was to investigate the impacts of ozone dose and empty bed contact time (EBCT) in ozone-biofiltration systems on disinfection byproduct (DBP) formation potential. The data were used to evaluate the possibility of using DBP formation potential as an alternative guideline for total organic carbon (TOC) removal in potable reuse applications. A pilot-scale ozone-biofiltration system was operated with O 3 /TOC ratios ranging from 0.1 to 2.25 and EBCTs ranging from 2 to 20 min. The biofiltration columns contained anthracite or biological activated carbon (BAC). Bench-scale chlorination was performed using the uniform formation conditions (UFC) approach, and quenched samples were analyzed for total trihalomethanes (TTHMs) and regulated haloacetic acids (HAA5s). The data demonstrated that ozone-biofiltration achieved TOC removals ranging from ∼10 to 30%, depending on operational conditions, but biofiltration without ozone generally achieved <10% TOC removal. UFC testing demonstrated that ozone alone was efficient in transforming bulk organic matter and reducing DBP formation potential by 10-30%. The synergistic combination of ozone and biofiltration achieved average overall reductions in TTHM and HAA5 formation potential of 26% and 51%, respectively. Finally, a maximum TOC concentration of 2.0 mg/L was identified as a recommended treatment target for reliable compliance with TTHM and HAA5 regulations for potable reuse systems in the United States. Copyright © 2018 Elsevier Ltd. All rights reserved.

Fixed bed column study for Cu (II) removal from aqueous solution using water hyacinth (Eichornia crassipes) biomass.

PubMed

Gandhimathi, R; Ramesh, S T; Yadu, Anubhav; Bharathi, K S

2013-07-01

This paper reports the results of the study on the performance of low-cost biosorbent water hyacinth (WH) in removing Cu (II) from aqueous solution. The adsorbent material adopted was found to be an efficient media for the removal of Cu (II) in continuous mode using fixed bed column. The column studies were conducted with 10 mg/L metal solution with a flow rate of 10 mL/min with different bed depths such as 10, 20 and 30 cm. The column design parameters like adsorption rate constant, adsorption capacity and minimum bed depth were calculated. It was found that, the adsorption capacity of copper ions by water hyacinth increased by increasing the bed depth and the contact time.

Mathematical modeling of the adsorption/desorption characteristics of anthocyanins from muscadine (Vitis rotundifolia cv. Noble) juice pomace on Amberlite FPX66 resin in a fixed bed column.

PubMed

Uzdevenes, Chad G; Gao, Chi; Sandhu, Amandeep K; Yagiz, Yavuz; Gu, Liwei

2018-03-24

Muscadine grape pomace, a by-product of juicing and wine-making, contains significant amounts of anthocyanin 3,5-diglucosides, known to be beneficial to human health. The objective of this research was to use mathematical modeling to investigate the adsorption/desorption characteristics of these anthocyanins from muscadine grape pomace on Amberlite FPX66 resin in a fixed bed column. Anthocyanins were extracted using hot water and ultrasound, and the extracts were loaded onto a resin column at five bed depths (5, 6, 8, 10 and 12 cm) using three flow rates (4, 6 and 8 mL min -1 ). It was found that adsorption on the column fitted the bed depth service time (BDST) model and the empty bed residence time (EBRT) model. Desorption was achieved by eluting the column using ethanol at four concentrations (25, 40, 55 and 70% v/v) and could be described with an empirical sigmoid model. The breakthrough curves of anthocyanins fitted the BDST model for all three flow rates with R 2 values of 0.983, 0.992 and 0.984 respectively. The EBRT model was successfully employed to find the operating lines, which allow for column scale-up while still achieving similar results to those found in a laboratory operation. Desorption with 40% (v/v) ethanol achieved the highest recovery rate of anthocyanins at 79.6%. The mathematical models established in this study can be used in designing a pilot/industrial- scale column for the separation and concentration of anthocyanins from muscadine juice pomace. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Odors as cues for orientation to mothers by weanling Virginia opossums

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holmes, D.J.

1992-12-01

Three experiments were conducted to investigate whether whole-body and pouch odors facilitate social cohesion between young Virginia opossums and their mothers just prior to weaning. In experiment 1, young oriented toward plastic buckets containing their mothers, directing significantly higher levels of investigative behavior and more distress vocalizations toward them than toward buckets containing unrelated lactating females. In experiment 2, young oriented toward and investigated empty buckets containing whole-body odors of their mothers more than empty buckets containing odors of other females. Similarly, more investigative behavior was directed toward plastic bucket lids containing pouch odors from subjects mothers than toward pouchmore » odors from unrelated females in experiment 3. These results suggest that social odors help young didelphid marsupials maintain contact with their mothers, as in other mammals, and that whole-body and pouch gland odors are important chemical signals in this nongregarious species.« less

Biomass drying in a pulsed fluidized bed without inert bed particles

DOE PAGES

Jia, Dening; Bi, Xiaotao; Lim, C. Jim; ...

2016-08-29

Batch drying was performed in the pulsed fluidized bed with various species of biomass particles as an indicator of gas–solid contact efficiency and mass transfer rate under different operating conditions including pulsation duty cycle and particle size distribution. The fluidization of cohesive biomass particles benefited from the shorter opening time of pulsed gas flow and increased peak pressure drop. The presence of fines enhanced gas–solid contact of large and irregular biomass particles, as well as the mass transfer efficiency. A drying model based on two-phase theory was proposed, from which effective diffusivity was calculated for various gas flow rates, temperaturemore » and pulsation frequency. Intricate relationship was discovered between pulsation frequency and effective diffusivity, as mass transfer was deeply connected with the hydrodynamics. Effective diffusivity was also found to be proportional to gas flow rate and drying temperature. In conclusion, operating near the natural frequency of the system also favored drying and mass transfer.« less

A geologic analysis of the Side-Looking Airborne Radar imagery of southern New England

USGS Publications Warehouse

Banks, Paul T.

1975-01-01

Analysis of the side looking airborn radar imagery of Massachusetts, Connecticut and Rhode Island indicates that radar shows the topography in great detail. Since bedrock geologic features are frequently expressed in the topography the radar lends itself to geologic interpretation. The radar was studied by comparisons with field mapped geologic data first at a scale of approximately 1:125,000 and then at a scale of 1:500,000. The larger scale comparison revealed that faults, minor faults, joint sets, bedding and foliation attitudes, lithology and lithologic contacts all have a topographic expression interpretable on the imagery. Surficial geologic features were far less visible on the imagery over most of the area studied. The smaller scale comparisons revealed a pervasive, near orthogonal fracture set cutting all types and ages of rock and trending roughly N40?E and N30?W. In certain places the strike of bedding and foliation attitudes and some lithologic Contacts were visible in addition to the fractures. Fracturing in southern New England is apparently far more important than has been previously recognized. This new information, together with the visibility of many bedding and foliation attitudes and lithologic contacts, indicates the importance of radar imagery in improving the geologic interpretation of an area.

Chemical analyses (raw laboratory data) and locality index maps of the Confederate Gulch area, Broadwater and Meagher Counties, Montana

USGS Publications Warehouse

,

1975-01-01

Analysis of the side looking airborn radar imagery of Massachusetts, Connecticut and Rhode Island indicates that radar shows the topography in great detail. Since bedrock geologic features are frequently expressed in the topography the radar lends itself to geologic interpretation. The radar was studied by comparisons with field mapped geologic data first at a scale of approximately 1:125,000 and then at a scale of 1:500,000. The larger scale comparison revealed that faults, minor faults, joint sets, bedding and foliation attitudes, lithology and lithologic contacts all have a topographic expression interpretable on the imagery. Surficial geologic features were far less visible on the imagery over most of the area studied. The smaller scale comparisons revealed a pervasive, near orthogonal fracture set cutting all types and ages of rock and trending roughly N40?E and N30?W. In certain places the strike of bedding and foliation attitudes and some lithologic Contacts were visible in addition to the fractures. Fracturing in southern New England is apparently far more important than has been previously recognized. This new information, together with the visibility of many bedding and foliation attitudes and lithologic contacts, indicates the importance of radar imagery in improving the geologic interpretation of an area.

Comparison of H2S adsorption by two hydrogel composite (HBC) derived by Empty Fruit Bunch (EFB) biochar and Coal Fly Ash (CFA)

NASA Astrophysics Data System (ADS)

Meri, N. H.; Alias, A. B.; Talib, N.; Rashid, Z. A.; Ghani, W. A. W. A. K.

2018-03-01

This study are covered the adsorption performance of two adsorbent Empty Fruit Bunch Hydrogel Biochar Composite (EFB-HBC) and Coal Fly Ash Hydrogel Composite (CFA-HC) on hydrogen sulphide. The EFB biochar were produce by pyrolysed and heated from room temperature to 550˚C at 10˚C/min under the Nitrogen flow. Meanwhile, coal fly ash collected from a power plant located in Selangor, Malaysia. Both of the materials is a waste from different industries and became the precursor to our adsorbents. EFB biochar and coal fly ash has been synthesized to become hydrogel by polymerization process with acrylamide (AAm) as monomer, N,N’-methylene bisacry lamide (MBA) as cross linker and ammonium persulfate (APS) as initiator. In addition, because of the speciality of hydrogel itself, which is has high ability in storing water, the effect of H2O wetness on EFB-HBC and CFA-HC were investigate in adsorption of H2S. EFB-HBC gave a longest breakthrough time and highest adsorption capacity compared with CFA-HC in both condition (dry/wet). The result also indicated that, the increased the bed height, increased the adsorption capacity.

Coupled large eddy simulation and discrete element model of bedload motion

NASA Astrophysics Data System (ADS)

Furbish, D.; Schmeeckle, M. W.

2011-12-01

We combine a three-dimensional large eddy simulation of turbulence to a three-dimensional discrete element model of turbulence. The large eddy simulation of the turbulent fluid is extended into the bed composed of non-moving particles by adding resistance terms to the Navier-Stokes equations in accordance with the Darcy-Forchheimer law. This allows the turbulent velocity and pressure fluctuations to penetrate the bed of discrete particles, and this addition of a porous zone results in turbulence structures above the bed that are similar to previous experimental and numerical results for hydraulically-rough beds. For example, we reproduce low-speed streaks that are less coherent than those over smooth-beds due to the episodic outflow of fluid from the bed. Local resistance terms are also added to the Navier-Stokes equations to account for the drag of individual moving particles. The interaction of the spherical particles utilizes a standard DEM soft-sphere Hertz model. We use only a simple drag model to calculate the fluid forces on the particles. The model reproduces an exponential distribution of bedload particle velocities that we have found experimentally using high-speed video of a flat bed of moving sand in a recirculating water flume. The exponential distribution of velocity results from the motion of many particles that are nearly constantly in contact with other bed particles and come to rest after short distances, in combination with a relatively few particles that are entrained further above the bed and have velocities approaching that of the fluid. Entrainment and motion "hot spots" are evident that are not perfectly correlated with the local, instantaneous fluid velocity. Zones of the bed that have recently experienced motion are more susceptible to motion because of the local configuration of particle contacts. The paradigm of a characteristic saltation hop length in riverine bedload transport has infused many aspects of geomorphic thought, including even bedrock erosion. In light of our theoretical, experimental, and numerical findings supporting the exponential distribution of bedload particle motion, the idea of a characteristic saltation hop should be scrapped or substantially modified.

Surface Effect Takeoff and Landing System (SETOLS)

DTIC Science & Technology

1974-04-01

State-of-the-Art 33 4. Program Tranisfer ~34 5. Future Research 34 6. Current Organizational Contacts and Identification 36 I REFE~RENCES 37 DEFENSE...ability to taxi over water, mud, low tree stumps, and empty and water-filled ditches. The flight tests indicated no significant changes in the...flight Lested from hard--surface runways, turf, water, snow, and fine sand. The aircraft also demonstrated the ability to taxi across mud, low tree

Sand Waves That Impede Navigation of Coastal Inlet Navigation Channels

DTIC Science & Technology

2006-08-01

Merrymeeting Bay. The bay collects coarse-grained sediment from unconsolidated ice-contact and periglacial deposits (Fenster and FitzGerald 1996). During...bed, which is a layer of denser or larger sized sediment left after finer material has been winnowed by a strong current, can inhibit bed form...Order Descriptors (important) • Superposition: simple or compound. • Sediment Characteristics (size, sorting). Third Order Descriptors (useful

Joint-bounded crescentic scars formed by subglacial clast-bed contact forces: Implications for bedrock failure beneath glaciers

NASA Astrophysics Data System (ADS)

Krabbendam, M.; Bradwell, T.; Everest, J. D.; Eyles, N.

2017-08-01

Glaciers and ice sheets are important agents of bedrock erosion, yet the precise processes of bedrock failure beneath glacier ice are incompletely known. Subglacially formed erosional crescentic markings (crescentic gouges, lunate fractures) on bedrock surfaces occur locally in glaciated areas and comprise a conchoidal fracture dipping down-ice and a steep fracture that faces up-ice. Here we report morphologically distinct crescentic scars that are closely associated with preexisting joints, termed here joint-bounded crescentic scars. These hitherto unreported features are ca. 50-200 mm deep and involve considerably more rock removal than previously described crescentic markings. The joint-bounded crescentic scars were found on abraded rhyolite surfaces recently exposed (< 20 years) beneath a retreating glacier in Iceland, as well as on glacially sculpted Precambrian gneisses in NW Scotland and various Precambrian rocks in Ontario, glaciated during the Late Pleistocene. We suggest a common formation mechanism for these contemporary and relict features, whereby a boulder embedded in basal ice produces a continuously migrating clast-bed contact force as it is dragged over the hard (bedrock) bed. As the ice-embedded boulder approaches a preexisting joint in the bedrock, stress concentrations build up in the bed that exceed the intact rock strength, resulting in conchoidal fracturing and detachment of a crescentic wedge-shaped rock fragment. Subsequent removal of the rock fragment probably involves further fracturing or crushing (comminution) under high contact forces. Formation of joint-bounded crescentic scars is favoured by large boulders at the base of the ice, high basal melting rates, and the presence of preexisting subvertical joints in the bedrock bed. We infer that the relative scarcity of crescentic markings in general on deglaciated surfaces shows that fracturing of intact bedrock below ice is difficult, but that preexisting weaknesses such as joints greatly facilitate rock failure. This implies that models of glacial erosion need to take fracture patterns of bedrock into account.

Shielded fluid stream injector for particle bed reactor

DOEpatents

Notestein, John E.

1993-01-01

A shielded fluid-stream injector assembly is provided for particle bed reactors. The assembly includes a perforated pipe injector disposed across the particle bed region of the reactor and an inverted V-shaped shield placed over the pipe, overlapping it to prevent descending particles from coming into direct contact with the pipe. The pipe and shield are fixedly secured at one end to the reactor wall and slidably secured at the other end to compensate for thermal expansion. An axially extending housing aligned with the pipe and outside the reactor and an in-line reamer are provided for removing deposits from the inside of the pipe. The assembly enables fluid streams to be injected and distributed uniformly into the particle bed with minimized clogging of injector ports. The same design may also be used for extraction of fluid streams from particle bed reactors.

Breaking a virus: Identifying molecular level failure modes of a viral capsid by multiscale modeling

NASA Astrophysics Data System (ADS)

Krishnamani, V.; Globisch, C.; Peter, C.; Deserno, M.

2016-10-01

We use coarse-grained (CG) simulations to study the deformation of empty Cowpea Chlorotic Mottle Virus (CCMV) capsids under uniaxial compression, from the initial elastic response up to capsid breakage. Our CG model is based on the MARTINI force field and has been amended by a stabilizing elastic network, acting only within individual proteins, that was tuned to capture the fluctuation spectrum of capsid protein dimers, obtained from all atom simulations. We have previously shown that this model predicts force-compression curves that match AFM indentation experiments on empty CCMV capsids. Here we investigate details of the actual breaking events when the CCMV capsid finally fails. We present a symmetry classification of all relevant protein contacts and show that they differ significantly in terms of stability. Specifically, we show that interfaces which break readily are precisely those which are believed to form last during assembly, even though some of them might share the same contacts as other non-breaking interfaces. In particular, the interfaces that form pentamers of dimers never break, while the virtually identical interfaces within hexamers of dimers readily do. Since these units differ in the large-scale geometry and, most noticeably, the cone-angle at the center of the 5- or 6-fold vertex, we propose that the hexameric unit fails because it is pre-stressed. This not only suggests that hexamers of dimers form less frequently during the early stages of assembly; it also offers a natural explanation for the well-known β-barrel motif at the hexameric center as a post-aggregation stabilization mechanism. Finally, we identify those amino acid contacts within all key protein interfaces that are most persistent during compressive deformation of the capsid, thereby providing potential targets for mutation studies aiming to elucidate the key contacts upon which overall stability rests.

Some properties of the walls of metaxylem vessels of maize roots, including tests of the wettability of their lumenal wall surfaces

PubMed Central

McCully, Margaret; Canny, Martin; Baker, Adam; Miller, Celia

2014-01-01

Background and Aims Since the proposal of the cohesion theory there has been a paradox that the lumenal surface of vessels is rich in hydrophobic lignin, while tension in the rising sap requires adhesion to a hydrophilic surface. This study sought to characterize the strength of that adhesion in maize (Zea mays), the wettability of the vessel surface, and to reconcile this with its histochemical and physical nature. Methods Wettability was assessed by emptying the maize root vessels of sap, perfusing them with either water or oil, and examining the adhesion (as revealed by contact angles) of the two liquids to vessel walls by cryo-scanning electron microscopy. The phobicity of the lumenal surface was also assessed histochemically with hydrophilic and hydrophobic probes. Key Results Pit borders in the lumen-facing vessel wall surface were wetted by both sap/water and oil. The attraction for oil was weaker: water could replace oil but not vice versa. Pit apertures repelled oil and were strongly stained by hydrophilic probes. Pit chambers were probably hydrophilic. Oil never entered the pits. When vessels were emptied and cryo-fixed immediately, pit chambers facing away from the vessels were always sap-filled. Pit chambers facing vessel lumens were either sap- or gas-filled. Sap from adjoining tracheary elements entering empty vessels accumulated on the lumenal surface in hemispherical drops, which spread out with decreasing contact angles to fill the lumen. Conclusions The vessel lumenal surface has a dual nature, namely a mosaic of hydrophilic and hydrophobic patches at the micrometre scale, with hydrophilic predominating. A key role is shown, for the first time, of overarching borders of pits in determining the dual nature of the surface. In gas-filled (embolized) vessels they are hydrophobic. When wetted by sap (vessels refilling or full) they are hydrophilic. A hypothesis is proposed to explain the switch between the two states. PMID:24709790

Behavioral Responses of the Bed Bug to Permethrin-Impregnated ActiveGuard™ Fabric.

PubMed

Jones, Susan C; Bryant, Joshua L; Harrison, Scott A

2013-06-07

ActiveGuard™ Mattress Liners have been used to control house dust mites, and they also are commercially available as an integrated pest management tool for use against bed bugs (Cimex lectularius). The aim of our study was to evaluate responses of numerous populations of the bed bug to the permethrin-impregnated fabric, with particular regard to contact toxicity, repellency, and feeding inhibition. Continuous exposure to ActiveGuard fabric resulted in rapid intoxication for three of four populations, with 87 to 100% of moderately pyrethroid-resistant and susceptible bed bugs succumbing by 1 d. In comparison, a highly resistant population reached 22% mortality at 10 d. Video data revealed that bed bugs readily traversed ActiveGuard fabric and spent a considerable amount of time moving about and resting on it during a 12-h period. ActiveGuard fabric was non-repellent to bed bugs from five tested populations. Furthermore, significantly fewer bed bugs successfully fed to repletion through ActiveGuard fabric than through blank fabric for the five populations. With just 30 min of feeding exposure, mortality ranged from 4% to 83%, depending upon the bed bug strain. These laboratory studies indicate that ActiveGuard liners adversely affected bed bugs from diverse populations.

Removal of Methylene Blue and Orange-G from Waste Water Using Magnetic Biochar

NASA Astrophysics Data System (ADS)

Mubarak, N. M.; Fo, Y. T.; Al-Salim, Hikmat Said; Sahu, J. N.; Abdullah, E. C.; Nizamuddin, S.; Jayakumar, N. S.; Ganesan, P.

2015-04-01

The study on the removal of methylene blue (MB) and orange-G dyes using magnetic biochar derived from the empty fruit bunch (EFB) was carried out. Process parameters such as pH, adsorbent dosage, agitation speed and contact time were optimized using Design-Expert Software v.6.0.8. The statistical analysis reveals that the optimum conditions for the maximum adsorption of MB are at pH 2 and pH 10, dosage 1.0 g, and agitation speed and contact time of 125 rpm and 120 min respectively. While for orange-G, at pH 2, dosage 1.0 g, and agitation speed and contact time of 125 rpm and 120 min respectively. The maximum adsorption capacity of 31.25 mg/g and 32.36 mg/g for MB and orange-G respectively. The adsorption kinetic for both dyes obeyed pseudo-second order.

Knowledge, access and utilization of bed-nets among stable and seasonal migrants in an artemisinin resistance containment area of Myanmar.

PubMed

Phyo Than, Wint; Oo, Tin; Wai, Khin Thet; Thi, Aung; Owiti, Philip; Kumar, Binay; Deepak Shewade, Hemant; Zachariah, Rony

2017-09-14

Myanmar lies in the Greater Mekong sub-region of South-East Asia faced with the challenge of emerging resistance to artemisinin combination therapies (ACT). Migrant populations are more likely than others to spread ACT resistance. A vital intervention to reduce malaria transmission, resistance spread and eliminate malaria is the use of bed nets. Among seasonal and stable migrants in an artemisinin resistance containment region of Myanmar, we compared a) their household characteristics, b) contact with health workers and information material, and c) household knowledge, access and utilization of bed nets. Secondary data from community-based surveys on 2484 migrant workers (2013 and 2014, Bago Region) were analyzed of which 37% were seasonal migrants. Bed net access and utilization were assessed using a) availability of at least one bed net per household, and b) one bed net per two persons, and c) proportion of household members who slept under abed net during the previous night (Indicator targets = 100%). Over 70% of all migrants were from unstable work settings with short transitory stays. Average household size was five (range 1-25) and almost half of all households had children under-five years. Roughly 10 % of migrants were night-time workers. Less than 40% of households had contact with health workers and less than 30% had exposure to information education and communication (IEC) materials, the latter being significantly lower among seasonal migrants. About 70% of households were aware of the importance of insecticide-treated bed-nets/long-lasting insecticidal nets (ITNs/LLINs), but knowledge on insecticide impregnation and retreatment of ITNs was poor (< 10%). Although over 95% of households had access to at least one bed net, the number with one bed net per two persons was grossly inadequate (13% for stable migrants and 9% for seasonal migrants, P = 0.001). About half of all household members slept under a bed net during the previous night. This study reveals important short-falls in knowledge, access and utilization of bed nets among migrants in Myanmar. Possible ways forward include frequent distribution campaigns to compensate for short transitory stays, matching household distributions to household size, enhanced information campaigns and introducing legislation to make mosquito repellents available for night-time workers at plantations and farms. Better understanding through qualitative research is also merited.

Fluid flow through a high cell density fluidized-bed during centrifugal bioreactor culture.

PubMed

Detzel, Christopher J; Van Wie, Bernard J; Ivory, Cornelius F

2010-01-01

An increasing demand for products such as tissues, proteins, and antibodies from mammalian cell suspension cultures is driving interest in increasing production through high-cell density bioreactors. The centrifugal bioreactor (CCBR) retains cells by balancing settling forces with surface drag forces due to medium throughput and is capable of maintaining cell densities above 10(8) cells/mL. This article builds on a previous study where the fluid mechanics of an empty CCBR were investigated showing fluid flow is nonuniform and dominated by Coriolis forces, raising concerns about nutrient and cell distribution. In this article, we demonstrate that the previously reported Coriolis forces are still present in the CCBR, but masked by the presence of cells. Experimental dye injection observations during culture of 15 microm hybridoma cells show a continual uniform darkening of the cell bed, indicating the region of the reactor containing cells is well mixed. Simulation results also indicate the cell bed is well mixed during culture of mammalian cells ranging in size from 10 to 20 microm. However, simulations also allow for a slight concentration gradient to be identified and attributed to Coriolis forces. Experimental results show cell density increases from 0.16 to 0.26 when centrifugal force is doubled by increasing RPM from 650 to 920 at a constant inlet velocity of 6.5 cm/s; an effect also observed in the simulation. Results presented in this article indicate cells maintained in the CCBR behave as a high-density fluidized bed of cells providing a homogeneous environment to ensure optimal growth conditions. (c) 2010 American Institute of Chemical Engineers

Fluid Flow through a High Cell Density Fluidized-Bed during Centrifugal Bioreactor Culture

PubMed Central

Detzel, Christopher J.; Van Wie, Bernard J.; Ivory, Cornelius F.

2010-01-01

An increasing demand for products such as tissues, proteins, and antibodies from mammalian cell suspension cultures is driving interest in increasing production through high-cell density bioreactors. The centrifugal bioreactor (CCBR) retains cells by balancing settling forces with surface drag forces due to medium throughput and is capable of maintaining cell densities above 108 cells/mL. This article builds on a previous study where the fluid mechanics of an empty CCBR were investigated showing fluid flow is nonuniform and dominated by Coriolis forces, raising concerns about nutrient and cell distribution. In this article, we demonstrate that the previously reported Coriolis forces are still present in the CCBR, but masked by the presence of cells. Experimental dye injection observations during culture of 15 μm hybridoma cells show a continual uniform darkening of the cell bed, indicating the region of the reactor containing cells is well mixed. Simulation results also indicate the cell bed is well mixed during culture of mammalian cells ranging in size from 10 to 20 μm. However, simulations also allow for a slight concentration gradient to be identified and attributed to Coriolis forces. Experimental results show cell density increases from 0.16 to 0.26 when centrifugal force is doubled by increasing RPM from 650 to 920 at a constant inlet velocity of 6.5 cm/s; an effect also observed in the simulation. Results presented in this article indicate cells maintained in the CCBR behave as a high-density fluidized bed of cells providing a homogeneous environment to ensure optimal growth conditions. PMID:20205172

[Removal of mixed waste gases by the biotrickling filter].

PubMed

Zhang, Ding-Feng; Fang, Jun-Yi; Ye, Jie-Xu; Qiu, Song-Kai; Qian, Dong-Sheng; Dai, Qi-Zhou; Chen, Dong-Zhi

2013-06-01

A biotrickling filter (BTF) was designed for treating mixed waste gases, which contained hydrogen sulfide (H2S), tetrahydrofuran (THF) and dichloromethane (DCM) at the start-up and steady states. The removal efficiency of H2S and DCM could maintain about 99% and 60%, respectively, and the removal efficiency of DCM was reduced from 90% to 37% with the shortening empty bed retention time (EBRT) form 50 to 20 seconds when the inlet concentrations were 200, 100, 100 mg x m(-3) of H2S, THF, DCM, respectively. In the theoretical study, the biodegradation efficiency of contaminants was H2S > THF > DCM by analyzing the Michaelis-Menten Dynamic model.

A flexible proximity sensor formed by duplex screen/screen-offset printing and its application to non-contact detection of human breathing

NASA Astrophysics Data System (ADS)

Nomura, Ken-Ichi; Kaji, Ryosaku; Iwata, Shiro; Otao, Shinobu; Imawaka, Naoto; Yoshino, Katsumi; Mitsui, Ryosuke; Sato, Junya; Takahashi, Seiya; Nakajima, Shin-Ichiro; Ushijima, Hirobumi

2016-01-01

We describe a flexible capacitance-type sensor that can detect an approaching human without contact, fabricated by developing and applying duplex conductive-ink printing to a film substrate. The results of our calculations show that the difference in size between the top and bottom electrodes of the sensor allows for the spatial extension of the electric field distribution over the electrodes. Hence, such a component functions as a proximity sensor. This thin and light device with a large form factor can be arranged at various places, including curved surfaces and the back of objects such that it is unnoticeable. In our experiment, we attached it to the back of a bed, and found that our device successfully detected the breathing of a subject on the bed without contacting his body. This should contribute to reducing the physical and psychological discomfort among patients during medical checks, or when their condition is being monitored.

A flexible proximity sensor formed by duplex screen/screen-offset printing and its application to non-contact detection of human breathing

PubMed Central

Nomura, Ken-ichi; Kaji, Ryosaku; Iwata, Shiro; Otao, Shinobu; Imawaka, Naoto; Yoshino, Katsumi; Mitsui, Ryosuke; Sato, Junya; Takahashi, Seiya; Nakajima, Shin-ichiro; Ushijima, Hirobumi

2016-01-01

We describe a flexible capacitance-type sensor that can detect an approaching human without contact, fabricated by developing and applying duplex conductive-ink printing to a film substrate. The results of our calculations show that the difference in size between the top and bottom electrodes of the sensor allows for the spatial extension of the electric field distribution over the electrodes. Hence, such a component functions as a proximity sensor. This thin and light device with a large form factor can be arranged at various places, including curved surfaces and the back of objects such that it is unnoticeable. In our experiment, we attached it to the back of a bed, and found that our device successfully detected the breathing of a subject on the bed without contacting his body. This should contribute to reducing the physical and psychological discomfort among patients during medical checks, or when their condition is being monitored. PMID:26795237

A mathematical model of Clostridium difficile transmission in medical wards and a cost-effectiveness analysis comparing different strategies for laboratory diagnosis and patient isolation.

PubMed

Schechner, Vered; Carmeli, Yehuda; Leshno, Moshe

2017-01-01

Clostridium difficile infection (CDI) is a common and potentially fatal healthcare-associated infection. Improving diagnostic tests and infection control measures may prevent transmission. We aimed to determine, in resource-limited settings, whether it is more effective and cost-effective to allocate resources to isolation or to diagnostics. We constructed a mathematical model of CDI transmission based on hospital data (9 medical wards, 350 beds) between March 2010 and February 2013. The model consisted of three compartments: susceptible patients, asymptomatic carriers and CDI patients. We used our model results to perform a cost-effectiveness analysis, comparing four strategies that were different combinations of 2 test methods (the two-step test and uniform PCR) and 2 infection control measures (contact isolation in multiple-bed rooms or single-bed rooms/cohorting). For each strategy, we calculated the annual cost (of CDI diagnosis and isolation) for a decrease of 1 in the average daily number of CDI patients; the strategy of the two-step test and contact isolation in multiple-bed rooms was the reference strategy. Our model showed that the average number of CDI patients increased exponentially as the transmission rate increased. Improving diagnosis by adopting uniform PCR assay reduced the average number of CDI cases per day per 350 beds from 9.4 to 8.5, while improving isolation by using single-bed rooms reduced the number to about 1; the latter was cost saving. CDI can be decreased by better isolation and more sensitive laboratory methods. From the hospital perspective, improving isolation is more cost-effective than improving diagnostics.

A mathematical model of Clostridium difficile transmission in medical wards and a cost-effectiveness analysis comparing different strategies for laboratory diagnosis and patient isolation

PubMed Central

Carmeli, Yehuda; Leshno, Moshe

2017-01-01

Background Clostridium difficile infection (CDI) is a common and potentially fatal healthcare-associated infection. Improving diagnostic tests and infection control measures may prevent transmission. We aimed to determine, in resource-limited settings, whether it is more effective and cost-effective to allocate resources to isolation or to diagnostics. Methods We constructed a mathematical model of CDI transmission based on hospital data (9 medical wards, 350 beds) between March 2010 and February 2013. The model consisted of three compartments: susceptible patients, asymptomatic carriers and CDI patients. We used our model results to perform a cost-effectiveness analysis, comparing four strategies that were different combinations of 2 test methods (the two-step test and uniform PCR) and 2 infection control measures (contact isolation in multiple-bed rooms or single-bed rooms/cohorting). For each strategy, we calculated the annual cost (of CDI diagnosis and isolation) for a decrease of 1 in the average daily number of CDI patients; the strategy of the two-step test and contact isolation in multiple-bed rooms was the reference strategy. Results Our model showed that the average number of CDI patients increased exponentially as the transmission rate increased. Improving diagnosis by adopting uniform PCR assay reduced the average number of CDI cases per day per 350 beds from 9.4 to 8.5, while improving isolation by using single-bed rooms reduced the number to about 1; the latter was cost saving. Conclusions CDI can be decreased by better isolation and more sensitive laboratory methods. From the hospital perspective, improving isolation is more cost-effective than improving diagnostics. PMID:28187144

The local heat transfer mathematical model between vibrated fluidized beds and horizontal tubes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Xuejun; College of Biology and Chemical Engineering, Panzhihua University, Panzhihua 617000; Ye, Shichao

2008-05-15

A dimensionless mathematical model is proposed to predict the local heat transfer coefficients between vibrated fluidized beds and immersed horizontal tubes, and the effects of the thickness of gas film and the contact time of particle packets are well considered. Experiments using the glass beads (the average diameter bar d{sub p}=1.83mm) were conducted in a two-dimensional vibrated fluidized bed (240 mm x 80 mm). The local heat transfer law between vibrated fluidized bed and horizontal tube surface has been investigated. The results show that the values of theoretical prediction are in good agreement with experimental data, so the model ismore » able to predict the local heat transfer coefficients between vibrated fluidized beds and immersed horizontal tubes reasonably well, and the error is in range of {+-}15%. The results can provide references for future designing and researching on the vibrated fluidized beds with immersed horizontal tubes. (author)« less

Partially confined configuration for the growth of semiconductor crystals from the melt in zero-gravity environment

NASA Technical Reports Server (NTRS)

Lagowski, J.; Gatos, H. C.; Dabkowski, F. P.

1985-01-01

A novel partially confined configuration is proposed for the crystal growth of semiconductors from the melt, including those with volatile constituents. A triangular prism is employed to contain the growth melt. Due to surface tension, the melt will acquire a cylindrical-like shape and thus contact the prism along three parallel lines. The three empty spaces between the cylindrical melt and the edges of the prism will accommodate the expansion of the solidifying semiconductor, and in the case of semiconductor compounds with a volatile constituent, will permit the presence of the desired vapor phase in contact with the melt for controlling the melt stoichiometry. Theoretical and experimental evidence in support of this new type of confinement is presented.

Biological floating bed and bio-contact oxidation processes for landscape water treatment: simultaneous removal of Microcystis aeruginosa, TOC, nitrogen and phosphorus.

PubMed

Su, Jun Feng; Liang, Dong Hui; Fu, Le; Wei, Li; Ma, Min

2018-06-13

The aim of this study was to identify algicidal bacteria J25 against the Microcystis aeruginosa (90.14%), Chlorella (78.75%), Scenedesmus (not inhibited), and Oscillatoria (90.12%). Meanwhile, we evaluate the SOD activity and efficiency of denitrification characteristics with Acinetobacter sp. J25. A novel hybrid bioreactor combined biological floating bed with bio-contact oxidation (BFBO) was designed for treating the landscape water, and the average removal efficiencies of nitrate-N, ammonia-N, nitrite-N, TN, TP, TOC, and algal cells were 91.14, 50, 87.86, 88.83, 33.07, 53.95, and 53.43%, respectively. A 454-pyrosequencing technology was employed to investigate the microbial communities of the BFBO reactor samples. The results showed that Acinetobacter sp. J25 was the dominant contributor for effective removal of N, algal cells, and TOC in the BFBO reactor. And the relative abundance of Acinetobacter showed increase trend with the delay of reaction time. Graphical abstract Biological floating bed and bio-contact oxidation (BFBO) as a novel hybrid bioreactor designed for simultaneous removal Microcystis aeruginosa, TOC, nitrogen, and phosphorus. And high-throughput sequencing data demonstrated that Acinetobacter sp. J25 was the dominate species in the reactor and played key roles in the removal of N, TOC, and M. aeruginosa. Proposed reaction mechanism of the BFBO.

Ringworm (Body)

MedlinePlus

... clothing, towels, bedding and linens, combs, and brushes. Soil to human. In rare cases, ringworm can be spread to humans by contact with infected soil. Infection would most likely occur only from prolonged ...

Fuel cell system combustor

DOEpatents

Pettit, William Henry

2001-01-01

A fuel cell system including a fuel reformer heated by a catalytic combustor fired by anode and cathode effluents. The combustor includes a turbulator section at its input end for intimately mixing the anode and cathode effluents before they contact the combustors primary catalyst bed. The turbulator comprises at least one porous bed of mixing media that provides a tortuous path therethrough for creating turbulent flow and intimate mixing of the anode and cathode effluents therein.

Reactor for fluidized bed silane decomposition

NASA Technical Reports Server (NTRS)

Iya, Sridhar K. (Inventor)

1989-01-01

An improved heated fluidized bed reactor and method for the production of high purity polycrystalline silicon by silane pyrolysis wherein silicon seed particles are heated in an upper heating zone of the reactor and admixed with particles in a lower zone, in which zone a silane-containing gas stream, having passed through a lower cooled gas distribution zone not conducive to silane pyrolysis, contacts the heated seed particles whereon the silane is heterogeneously reduced to silicon.

Studies on the pretreatment of zeolite clinoptilolite in packed beds.

PubMed

Inglezakis, V J; Loizidou, M D; Grigoropoulou, H P

2004-02-01

The effect of volumetric flow rate, ranging from 5 to 45 Bed Volumes per hour (BV h(-1)) and temperature, ranging from 25 to 59 degrees C, during pretreatment of clinoptilolite on its effective capacity has been investigated. Pretreatment tests have been performed in an upflow ion exchange bed. Increased temperatures were found to increase the effective capacity of clinoptilolite. Effective capacity was maximal at low volumetric flow rates, indicating an influence of contact time and complete saturation of the zeolite bed at flow rates lower than 10 BV h(-1). Furthermore, a comparison between upflow and downflow operation at the same operating conditions showed that better results are obtained in upflow conditions, probably due to the better wetting of the material and the absence of liquid maldistribution.

Process of concentrating ethanol from dilute aqueous solutions thereof

DOEpatents

Oulman, C.S.; Chriswell, C.D.

1981-07-07

Relatively dilute aqueous solutions of ethanol are concentrated by passage through a bed of a crystalline silica polymorph, such as silicalite, to adsorb the ethanol with residual dilute feed in contact with the bed, which is displaced by passing concentrated aqueous ethanol through the bed without displacing the adsorbed ethanol. A product concentrate is then obtained by removing the adsorbed ethanol from the bed together with at least a portion of the concentrated aqueous ethanol used as the displacer liquid. This process permits ethanol to be concentrated from dilute fermentation beers, which may contain from 6 to 10% ethanol, to obtain a concentrate product at very low energy cost having an ethanol concentration in excess of 95%, such as a concentration of from 98 to 99.5%. 5 figs.

Process of concentrating ethanol from dilute aqueous solutions thereof

DOEpatents

Oulman, Charles S. [Ames, IA; Chriswell, Colin D. [Slater, IA

1981-07-07

Relatively dilute aqueous solutions of ethanol are concentrated by passage through a bed of a crystalline silica polymorph, such as silicalite, to adsorb the ethanol with residual dilute feed in contact with the bed, which is displaced by passing concentrated aqueous ethanol through the bed without displacing the adsorbed ethanol. A product concentrate is then obtained by removing the adsorbed ethanol from the bed together with at least a portion of the concentrated aqueous ethanol used as the displacer liquid. This process permits ethanol to be concentrated from dilute fermentation beers, which may contain from 6 to 10% ethanol, to obtain a concentrate product at very low energy cost having an ethanol concentration in excess of 95%, such as a concentration of from 98 to 99.5%.

Process for converting cellulosic materials into fuels and chemicals

DOEpatents

Scott, Charles D.; Faison, Brendlyn D.; Davison, Brian H.; Woodward, Jonathan

1994-01-01

A process for converting cellulosic materials, such as waste paper, into fuels and chemicals utilizing enzymatic hydrolysis of the major constituent of paper, cellulose. A waste paper slurry is contacted by cellulase in an agitated hydrolyzer. The cellulase is produced from a continuous, columnar, fluidized-bed bioreactor utilizing immobilized microorganisms. An attritor and a cellobiase reactor are coupled to the agitated hydrolyzer to improve reaction efficiency. The cellulase is recycled by an adsorption process. The resulting crude sugars are converted to dilute product in a fluidized-bed bioreactor utilizing microorganisms. The dilute product is concentrated and purified by utilizing distillation and/or a biparticle fluidized-bed bioreactor system.

Behavioral Responses of the Bed Bug to Permethrin-Impregnated ActiveGuard™ Fabric

PubMed Central

Jones, Susan C.; Bryant, Joshua L.; Harrison, Scott A.

2013-01-01

ActiveGuard™ Mattress Liners have been used to control house dust mites, and they also are commercially available as an integrated pest management tool for use against bed bugs (Cimex lectularius). The aim of our study was to evaluate responses of numerous populations of the bed bug to the permethrin-impregnated fabric, with particular regard to contact toxicity, repellency, and feeding inhibition. Continuous exposure to ActiveGuard fabric resulted in rapid intoxication for three of four populations, with 87 to 100% of moderately pyrethroid-resistant and susceptible bed bugs succumbing by 1 d. In comparison, a highly resistant population reached 22% mortality at 10 d. Video data revealed that bed bugs readily traversed ActiveGuard fabric and spent a considerable amount of time moving about and resting on it during a 12-h period. ActiveGuard fabric was non-repellent to bed bugs from five tested populations. Furthermore, significantly fewer bed bugs successfully fed to repletion through ActiveGuard fabric than through blank fabric for the five populations. With just 30 min of feeding exposure, mortality ranged from 4% to 83%, depending upon the bed bug strain. These laboratory studies indicate that ActiveGuard liners adversely affected bed bugs from diverse populations. PMID:26464388

Role of electrostatic interactions in the assembly of empty spherical viral capsids

NASA Astrophysics Data System (ADS)

Šiber, Antonio; Podgornik, Rudolf

2007-12-01

We examine the role of electrostatic interactions in the assembly of empty spherical viral capsids. The charges on the protein subunits that make the viral capsid mutually interact and are expected to yield electrostatic repulsion acting against the assembly of capsids. Thus, attractive protein-protein interactions of nonelectrostatic origin must act to enable the capsid formation. We investigate whether the interplay of repulsive electrostatic and attractive interactions between the protein subunits can result in the formation of spherical viral capsids of a preferred radius. For this to be the case, we find that the attractive interactions must depend on the angle between the neighboring protein subunits (i.e., on the mean curvature of the viral capsid) so that a particular angle(s) is (are) preferred energywise. Our results for the electrostatic contributions to energetics of viral capsids nicely correlate with recent experimental determinations of the energetics of protein-protein contacts in the hepatitis B virus [P. Ceres A. Zlotnick, Biochemistry 41, 11525 (2002)].

Modeling environmental contamination in hospital single- and four-bed rooms.

PubMed

King, M-F; Noakes, C J; Sleigh, P A

2015-12-01

Aerial dispersion of pathogens is recognized as a potential transmission route for hospital acquired infections; however, little is known about the link between healthcare worker (HCW) contacts' with contaminated surfaces, the transmission of infections and hospital room design. We combine computational fluid dynamics (CFD) simulations of bioaerosol deposition with a validated probabilistic HCW-surface contact model to estimate the relative quantity of pathogens accrued on hands during six types of care procedures in two room types. Results demonstrate that care type is most influential (P < 0.001), followed by the number of surface contacts (P < 0.001) and the distribution of surface pathogens (P = 0.05). Highest hand contamination was predicted during Personal care despite the highest levels of hand hygiene. Ventilation rates of 6 ac/h vs. 4 ac/h showed only minor reductions in predicted hand colonization. Pathogens accrued on hands decreased monotonically after patient care in single rooms due to the physical barrier of bioaerosol transmission between rooms and subsequent hand sanitation. Conversely, contamination was predicted to increase during contact with patients in four-bed rooms due to spatial spread of pathogens. Location of the infectious patient with respect to ventilation played a key role in determining pathogen loadings (P = 0.05). We present the first quantitative model predicting the surface contacts by HCW and the subsequent accretion of pathogenic material as they perform standard patient care. This model indicates that single rooms may significantly reduce the risk of cross-contamination due to indirect infection transmission. Not all care types pose the same risks to patients, and housekeeping performed by HCWs may be an important contribution in the transmission of pathogens between patients. Ventilation rates and positioning of infectious patients within four-bed rooms can mitigate the accretion of pathogens, whereby reducing the risk of missed hand hygiene opportunities. The model provides a tool to quantitatively evaluate the influence of hospital room design on infection risk. © 2015 The Authors. Indoor Air Published by John Wiley & Sons Ltd.

Removing organic and nitrogen content from a highly saline municipal wastewater reverse osmosis concentrate by UV/H2O2-BAC treatment.

PubMed

Pradhan, Shovana; Fan, Linhua; Roddick, Felicity A

2015-10-01

Reverse osmosis (RO) concentrate (ROC) streams generated from RO-based municipal wastewater reclamation processes pose potential health and environmental risks on their disposal to confined water bodies such as bays. A UV/H2O2 advanced oxidation process followed by a biological activated carbon (BAC) treatment was evaluated at lab-scale for the removal of organic and nutrient content from a highly saline ROC (TDS 16 g L(-1), EC 23.5 mS cm(-1)) for its safe disposal to the receiving environment. Over the 230-day operation of the UV/H2O2-BAC process, the colour and UV absorbance (254 nm) of the ROC were reduced to well below those of the influent to the reclamation process. The concentrations of DOC and total nitrogen (TN) were reduced by approximately 60% at an empty bed contact time (EBCT) of 60 min. The reduction in ammonia nitrogen by the BAC remained high under all conditions tested (>90%). Further investigation confirmed that the presence of residual peroxide in the UV/H2O2 treated ROC was beneficial for DOC removal, but markedly inhibited the activities of the nitrifying bacteria (i.e., nitrite oxidising bacteria) in the BAC system and hence compromised total nitrogen removal. This work demonstrated that the BAC treatment could be acclimated to the very high salinity environment, and could be used as a robust method for the removal of organic matter and nitrogen from the pre-oxidised ROC under optimised conditions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of advanced oxidation on N-nitrosodimethylamine (NDMA) formation and microbial ecology during pilot-scale biological activated carbon filtration.

PubMed

Li, Dong; Stanford, Ben; Dickenson, Eric; Khunjar, Wendell O; Homme, Carissa L; Rosenfeldt, Erik J; Sharp, Jonathan O

2017-04-15

Water treatment combining advanced oxidative processes with subsequent exposure to biological activated carbon (BAC) holds promise for the attenuation of recalcitrant pollutants. Here we contrast oxidation and subsequent biofiltration of treated wastewater effluent employing either ozone or UV/H 2 O 2 followed by BAC during pilot-scale implementation. Both treatment trains largely met target water quality goals by facilitating the removal of a suite of trace organics and bulk water parameters. N-nitrosodimethylamine (NDMA) formation was observed in ozone fed BAC columns during biofiltration and to a lesser extent in UV/H 2 O 2 fed columns and was most pronounced at 20 min of empty bed contact time (EBCT) when compared to shorter EBCTs evaluated. While microbial populations were highly similar in the upper reaches, deeper samples revealed a divergence within and between BAC filtration systems where EBCT was identified to be a significant environmental predictor for shifts in microbial populations. The abundance of Nitrospira in the top samples of both columns provides an explanation for the oxidation of nitrite and corresponding increases in nitrate concentrations during BAC transit and support interplay between nitrogen cycling with nitrosamine formation. The results of this study demonstrate that pretreatments using ozone versus UV/H 2 O 2 impart modest differences to the overall BAC microbial population structural and functional attributes, and further highlight the need to evaluate NDMA formation prior to full-scale implementation of BAC in potable reuse applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Infrared Thermography for Monitoring of Freeze-Drying Processes: Instrumental Developments and Preliminary Results

PubMed Central

Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

2014-01-01

Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from −40°C to 25°C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5°C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8°C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13°C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10°C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes. © 2014 European Union 103:2088–2097, 2014 PMID:24902839

Infrared thermography for monitoring of freeze-drying processes: instrumental developments and preliminary results.

PubMed

Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

2014-07-01

Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from -40 °C to 25 °C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5 °C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8 °C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13 °C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10 °C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes. © 2014 European Union.

Potential of Essential Oil-Based Pesticides and Detergents for Bed Bug Control.

PubMed

Singh, Narinderpal; Wang, Changlu; Cooper, Richard

2014-12-01

The bed bug, (Cimex lectularius L.), is a difficult pest to control. Prevalence of insecticide resistance among bed bug populations and concerns over human-insecticide exposure has stimulated the development of alternative bed bug control materials. Many essential oil-based pesticides and detergent insecticides targeting bed bugs have been developed in recent years. We evaluated the efficacy of nine essential oil-based products and two detergents using direct spray and residual contact bioassays in the laboratory. Two conventional insecticides, Temprid SC (imidacloprid and β-cyfluthrin) and Demand CS (λ-cyhalothrin), were used for comparison. Among the 11 nonsynthetic insecticides tested, only EcoRaider (1% geraniol, 1% cedar extract, and 2% sodium lauryl sulfate) and Bed Bug Patrol (0.003% clove oil, 1% peppermint oil, and 1.3% sodium lauryl sulfate) caused >90% mortality of nymphs in direct spray and forced exposure residual assays. However, the efficacy of EcoRaider and Bed Bug Patrol was significantly lower than that of Temprid SC and Demand CS in choice exposure residual bioassay. Direct spray of EcoRaider caused 87% egg mortality, whereas the other nonsynthetic insecticides had little effect on bed bug eggs. EcoRaider and Bed Bug Patrol did not exhibit detectable repellency against bed bugs in the presence of a carbon dioxide source. These findings suggest that EcoRaider and Bed Bug Patrol are potentially useful pesticides for controlling bed bug infestations, but further testing in naturally infested environments is needed. © 2014 Entomological Society of America.

Bugging forecast: unknown, disliked, occasionally intimate. Bed bugs in Germany meet unprepared people.

PubMed

Seidel, Conrad; Reinhardt, Klaus

2013-01-01

Bed bugs appear to be feared more than vector insects and other household pests. The reasons for this exaggerated fear are not fully understood. One hypothesis is that the folk knowledge on recognising and controlling bed bugs decreased as bed bugs became rarer in the 1960s and led to irrational perceptions. Here, we examine people's ability to recognise a bed bug and their response what to do in case of an infestation. We found that 13% of a sample of 391 people in four large German cities recognised a bed bug; 15% of all respondents would call a pest controller in case of bed bug infestation. This results in the pessimistic estimate that 97% of all early-stage infestations could go untreated. We discuss additional scenarios. The effectiveness of efforts to educate people about the presence of bed bugs has never been tested, but our sample is useful to guide future studies. We found three sources of information were associated with increased recognition rates of bed bugs: a) previous contacts with bed bugs (60% recognition), b) knowledge from friends or relatives (25%) and school or education courses (15%). By contrast, people who heard of bed bugs from television, print media or the Internet showed reduced recognition rates. We propose that the former factors be tested for educational interventions. In Germany, the bed bug is an estranged creature to many people, a fact that seems to hinder rational approaches to their control.

Bugging Forecast: Unknown, Disliked, Occasionally Intimate. Bed Bugs in Germany Meet Unprepared People

PubMed Central

Seidel, Conrad; Reinhardt, Klaus

2013-01-01

Bed bugs appear to be feared more than vector insects and other household pests. The reasons for this exaggerated fear are not fully understood. One hypothesis is that the folk knowledge on recognising and controlling bed bugs decreased as bed bugs became rarer in the 1960s and led to irrational perceptions. Here, we examine people’s ability to recognise a bed bug and their response what to do in case of an infestation. We found that 13% of a sample of 391 people in four large German cities recognised a bed bug; 15% of all respondents would call a pest controller in case of bed bug infestation. This results in the pessimistic estimate that 97% of all early-stage infestations could go untreated. We discuss additional scenarios. The effectiveness of efforts to educate people about the presence of bed bugs has never been tested, but our sample is useful to guide future studies. We found three sources of information were associated with increased recognition rates of bed bugs: a) previous contacts with bed bugs (60% recognition), b) knowledge from friends or relatives (25%) and school or education courses (15%). By contrast, people who heard of bed bugs from television, print media or the Internet showed reduced recognition rates. We propose that the former factors be tested for educational interventions. In Germany, the bed bug is an estranged creature to many people, a fact that seems to hinder rational approaches to their control. PMID:23300947

Squeeze-film flow between a flat impermeable bearing and an anisotropic porous bed

NASA Astrophysics Data System (ADS)

Karmakar, Timir; Raja Sekhar, G. P.

2018-04-01

We consider a theoretical model of the squeeze film in the presence of a porous bed. The gap between the porous bed and the bearing is assumed to be filled with a Newtonian fluid. We use the Navier-Stokes equation in the fluid region and the Darcy equation in the fluid filled porous region. Lubrication approximation is used to derive the corresponding evolution equation for the film thickness. We use G. S. Beavers and D. D. Joseph ["Boundary conditions at a naturally permeable wall," J. Fluid. Mech. 30, 197-207 (1967)] and M. Le Bars and M. G. Worster ["Interfacial conditions between a pure fluid and a porous medium: Implications for binary alloy solidification," J. Fluid. Mech. 550, 149-173 (2006)] condition at the liquid porous interface and present a detailed analysis on the corresponding impact. We assume that the porous bed is anisotropic in nature with permeabilities K2 and K1 along the principal axes. Accordingly, the anisotropic angle ϕ is taken as the angle between the horizontal direction and principal axis with permeability K2. We show that the anisotropic permeability ratio and the anisotropic angle make a significant influence on the contact time, flux, velocity, etc. Contact time to meet the porous bed when a bearing approaches under a constant prescribed load is estimated. We present some important findings (relevant to the knee joint) based on the anisotropic properties of the human cartilage. For a prescribed constant load, we have estimated the time duration, during which a healthy human knee remains fluid lubricated.

Preferences of lame cows for type of surface and level of social contact in hospital pens.

PubMed

Jensen, M B; Herskin, M S; Thomsen, P T; Forkman, B; Houe, H

2015-07-01

To investigate preferences of lame cows for flooring and level of social contact, 37 lame, lactating dairy cows (diagnosed with sole ulcer or white line disease) were housed individually for 6 d in experimental hospital pens, where they could choose between 2 equally sized areas (6m × 4.5m) with either deep-bedded sand or a rubber surface. On both surfaces, cows could choose between 2 equally sized areas either near or away from heifers in a neighboring group pen. Cows spent more time lying on the deep-bedded sand than on the rubber surface (870 vs. 71min/d), whereas they spent less time upright (standing or walking) on the sand than on the rubber surface (180 vs. 319min/d). In addition, cows spent less time self-grooming on the sand than on the rubber surface (2.2 vs. 4.7% of time spent upright). With regard to level of social contact, cows spent more time near the neighboring heifers than away from them; this was true both while lying (565 vs. 374min/d) and upright (276 vs. 223min/d). Self-grooming was seen significantly more near neighboring heifers than away from them (4.8 vs. 3.3% of time spent upright). When lying, cows more often positioned themselves in areas of the pen where they could maintain visual contact with neighboring heifers. Lame cows with sole ulcers or white line disease preferred deep-bedded sand for lying, and preferred to perform self-grooming while on the rubber surface. Similarly, they preferred to lie and to perform self-grooming while positioned near animals in a neighboring pen. These results suggest that provision of a deep-bedded lying area in hospital pens is important to the welfare of lame cows. We found no evidence of isolation-seeking behavior in animals with these diagnoses (and no systemic symptoms) while they were kept in individual hospital pens. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Chemistry of the Materials Above and Below an Unconformity Between the Murray and Stimson Formations in Gale Crater, Mars

NASA Astrophysics Data System (ADS)

Newsom, H. E.; Belgacem, I.; Wiens, R. C.; Frydenvang, J.; Gasnault, O.; Maurice, S.; Gasda, P. J.; Clegg, S. M.; Cousin, A.; Rapin, W.; Jackson, R.; Vaci, Z.; Ha, B.; Blaney, D. L.; Bridges, N.; Francis, R.; Payré, V.; Gupta, S.; Banham, S.; Schroeder, J.; Calef, F. J., III; Edgett, K. S.; Fey, D.; Fisk, M. R.; Gellert, R.; Thompson, L. M.; Perrett, G. M.; Grotzinger, J. P.; Rubin, D. M.; Williams, A.; Kah, L. C.; Kronyak, R. E.

2015-12-01

MSL began investigating a contact between Murray formation, (fine grained lake deposits) and the younger Stimson formation at Marias Pass in May 2015, on the lower slopes of Mt. Sharp. Images show that the Murray formation, with numerous calcium sulfate veins compared to the Stimson, is truncated at an erosional contact. MAHLI images show a white layer a few mm thick at the contact that might be calcium sulfate. The lowermost beds of the Stimson unit in the Missoula area comprise horizontally laminated or cross-laminated sandstones. The sandstones are poorly sorted with floating granules and very coarse sand grains set in a fine- medium-grained sand 'matrix'. This material directly above the contact is a resistant, basal ledge-forming layer that also forms numerous blocks of float on top of the eroded Murray. This basal layer contains light toned fragments, possibly calcium sulfate, eroded from the Murray. The poor sorting and presence of sub-angular grains, together with the absence of preferential sorting into size sorted layers would seem to rule out eolian processes for the lowermost beds of the Stimson and suggest fluvial processes were responsible for deposition of these beds. For chemostratigraphy, the distance of each ChemCam or APXS observation above or below the contact was determined from images and the NavCam stereo mesh. The top of the Murray near the Missoula area is variable in composition, and additional analyses are planned to determine if weathering occurred at the eroded surface. Above the contact, the lowest 2 cm of the resistant slab is higher in SiO2, and lower in Al2O3, K2O and Na2O, relative to other Stimson analyses. In a few points with low totals, there is a correlation between Ca and missing components (presumed to be mostly S). These points could be connected to calcium sulfate in the form of cements and/or incorporation of eroded clasts of Murray vein materials.

Climbing Ability of the Common Bed Bug (Hemiptera: Cimicidae).

PubMed

Hottel, B A; Pereira, R M; Gezan, S A; Qing, R; Sigmund, W M; Koehler, P G

2015-05-01

Little is known about what factors influence the climbing ability of bed bugs, Cimex lectularius L. (Hemiptera: Cimicidae), in relation to the various surfaces they encounter. We examined how sex, time since last fed, and what surfaces the bed bugs were in contact with affected their climbing performance. The effects of sex and time since fed were tested by counting the number of bed bugs able to climb a 45° slope. The pulling force was recorded using an analytical balance technique that captured the sequential vertical pulling force output of bed bugs attached to various surfaces. Recently fed female bed bugs were found to have the most difficulty in climbing smooth surfaces in comparison with males. This difference can be explained by the larger weight gained from bloodmeals by female bed bugs. A variety of vertical pulling forces were observed on surfaces ranging from sandpaper to talc powder-covered glass. For surfaces not treated with talc powder, bed bugs generated the least amount of vertical pulling force from synthetically created 0.6-µm plastron surfaces. This vast range in the ability of bed bugs to grip onto various surfaces may have implications on limiting bed bugs dispersal and hitchhiking behaviors. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Microwave-enhanced chemical processes

DOEpatents

Varma, Ravi

1990-01-01

A process for disposal of toxic wastes including chlorinated hydrocarbons, comprising, establishing a bed of non-metallic particulates having a high dielectric loss factor. Effecting intimate contact of the particulates and the toxic wastes at a temperature in excess of about 400.degree. C. in the presence of microwave radiation for a time sufficient to break the hydrocarbon chlorine bonds and provide detoxification values in excess of 80 and further detoxifying the bed followed by additional disposal of toxic wastes.

Zone heating for fluidized bed silane pyrolysis

NASA Technical Reports Server (NTRS)

Iya, Sridhar K. (Inventor)

1987-01-01

An improved heated fluidized bed reactor and method for the production of high purity polycrystalline silicon by silane pyrolysis wherein silicon seed particles are heated in an upper heating zone of the reactor and admixed with particles in a lower reaction zone, in which zone a silane-containing gas stream, having passed through a lower cooled gas distribution zone not conducive to silane pyrolysis, contacts the heated seed particles whereon the silane is heterogeneously reduced to silicon.

Implications of contact metamorphism of Mancos Shale for critical zone processes

NASA Astrophysics Data System (ADS)

Navarre-Sitchler, A.

2016-12-01

Bedrock lithology imparts control on some critical zone processes, for example rates and extent of chemical weathering, solute release though mineral dissolution, and water flow. Bedrock can be very heterogeneous resulting in spatial variability of these processes throughout a catchment. In the East River watershed outside of Crested Butte, Colorado, bedrock is dominantly comprised of the Mancos Shale; a Cretaceous aged, organic carbon rich marine shale. However, in some areas the Mancos Shale appears contact metamorphosed by nearby igneous intrusions resulting in a potential gradient in lithologic change in part of the watershed where impacts of lithology on critical zone processes can be evaluated. Samples were collected in the East River valley along a transect from the contact between the Tertiary Gothic Mountain laccolith of the Mount Carbon igneous system and the underlying Manocs shale. Porosity of these samples was analyzed by small-angle and ultra small-angle neutron scattering. Results indicate contact metamorphism decreases porosity of the shale and changes the pore shape from slightly anisotropic pores aligned with bedding in the unmetamorphosed shale to isotropic pores with no bedding alignment in the metamorphosed shales. The porosity analysis combined with clay mineralogy, surface area, carbon content and oxidation state, and solute release rates determined from column experiments will be used to develop a full understanding of the impact of contact metamorphism on critical zone processes in the East River.

Refining the dual olfactory hypothesis: pheromone reward and odour experience.

PubMed

Martínez-García, Fernando; Martínez-Ricós, Joana; Agustín-Pavón, Carmen; Martínez-Hernández, Jose; Novejarque, Amparo; Lanuza, Enrique

2009-06-25

In rodents, sexual advertisement and gender recognition are mostly (if not exclusively) mediated by chemosignals. Specifically, there is ample evidence indicating that female mice are 'innately' attracted by male sexual pheromones that have critical non-volatile components and are detected by the vomeronasal organ. These pheromones can only get access to the vomeronasal organ by active pumping mechanisms that require close contact with the source of the stimulus (e.g. urine marks) during chemoinvestigation. We have hypothesised that male sexual pheromones are rewarding to female mice. Indeed, male-soiled bedding can be used as a reinforcer to induce conditioned place preference, provided contact with the bedding is allowed. The neural mechanisms of pheromone reward seem, however, different from those employed by other natural reinforcers, such as the sweetness or postingestive effects of sucrose. In contrast to vomeronasal-detected male sexual pheromones, male-derived olfactory stimuli (volatiles) are not intrinsically attractive to female mice. However, after repeated exposure to male-soiled bedding, intact female mice develop an acquired preference for male odours. On the contrary, in females whose accessory olfactory bulbs have been lesioned, exposure to male-soiled bedding induces aversion to male odorants. These considerations, together with data on the different properties of olfactory and vomeronasal receptors, lead us to make a proposal for the complementary roles that the olfactory and vomeronasal systems play in intersexual attraction and in other forms of intra- or inter-species communication.

A Time-Frequency Respiration Tracking System using Non-Contact Bed Sensors with Harmonic Artifact Rejection

PubMed Central

Beattie, Zachary T.; Jacobs, Peter G.; Riley, Thomas C.; Hagen, Chad C.

2015-01-01

Sleep apnea is a serious health condition that affects many individuals and has been associated with serious health conditions such as cardiovascular disease. Clinical diagnosis of sleep apnea requires that a patient spend the night in a sleep clinic while being wired up to numerous obtrusive sensors. We are developing a system that utilizes respiration rate and breathing amplitude inferred from non-contact bed sensors (i.e. load cells placed under bed supports) to detect sleep apnea. Multi-harmonic artifacts generated either biologically or as a result of the impulse response of the bed have made it challenging to track respiration rate and amplitude with high resolution in time. In this paper, we present an algorithm that can accurately track respiration on a second-by-second basis while removing noise harmonics. The algorithm is tested using data collected from 5 patients during overnight sleep studies. Respiration rate is compared with polysomnography estimations of respiration rate estimated by a technician following clinical standards. Results indicate that certain subjects exhibit a large harmonic component of their breathing signal that can be removed by our algorithm. When compared with technician transcribed respiration rates using polysomnography signals, we demonstrate improved accuracy of respiration rate tracking using harmonic artifact rejection (mean error: 0.18 breaths/minute) over tracking not using harmonic artifact rejection (mean error: −2.74 breaths/minute). PMID:26738176

Batch and continuous (fixed-bed column) biosorption of crystal violet by Artocarpus heterophyllus (jackfruit) leaf powder.

PubMed

Saha, Papita Das; Chakraborty, Sagnik; Chowdhury, Shamik

2012-04-01

In this study, batch and fixed-bed column experiments were performed to investigate the biosorption potential of Artocarpus heterophyllus (jackfruit) leaf powder (JLP) to remove crystal violet (CV) from aqueous solutions. Batch biosorption studies were carried out as a function of solution pH, contact time, initial dye concentration and temperature. The biosorption equilibrium data showed excellent fit to the Langmuir isotherm model with maximum monolayer biosorption capacity of 43.39 mg g(-1) at pH 7.0, initial dye concentration=50 mg L(-1), temperature=293 K and contact time=120 min. According to Dubinin-Radushkevich (D-R) isotherm model, biosorption of CV by JLP was chemisorption. The biosorption kinetics followed the pseudo-second-order kinetic model. Thermodynamic analysis revealed that biosorption of CV from aqueous solution by JLP was a spontaneous and exothermic process. In order to ascertain the practical applicability of the biosorbent, fixed-bed column studies were also performed. The breakthrough time increased with increasing bed height and decreased with increasing flow rate. The Thomas model as well as the BDST model showed good agreement with the experimental results at all the process parameters studied. It can be concluded that JLP is a promising biosorbent for removal of CV from aqueous solutions. Copyright © 2011 Elsevier B.V. All rights reserved.

Surficial geology and distribution of post-impoundment sediment of the western part of Lake Mead based on a sidescan sonar and high-resolution seismic-reflection survey

USGS Publications Warehouse

Twichell, David C.; Cross, VeeAnn A.; Rudin, Mark J.; Parolski, Kenneth F.

1999-01-01

Sidescan sonar imagery and high-resolution seismic-reflection profiles were collected in Las Vegas Bay and Boulder Basin of Lake Mead to determine the surficial geology as well as the distribution and thickness of sediment that has accumulated in these areas of the lake since the completion of Hoover Dam in 1935 (Gould, 1951). Results indicate that the accumulation of post-impoundment sediment is restricted to the original Colorado River bed which runs down the axis of Boulder Basin from Boulder Canyon to Hoover Dam, and the old Las Vegas Creek bed that bisects Las Vegas Bay. The sediment cover along the original Colorado River bed is continuous and is typically greater than 10-m thick throughout much of its length with the thickness in some areas exceeding 35 meters. The flat-lying nature of the deposits suggests that they are the result of turbidity currents that flow the length of the lake. The sediment cover in Las Vegas Bay is much thinner (rarely exceeding 2 m in thickness) and more discontinuous. The source for these sediments presumably is Las Vegas Wash and a series of other ephemeral washes that empty into this part of the lake. The presence of sediments along the entire length of the Las Vegas Creek bed suggests that turbidity currents probably are active here as well, and that sediment has been transported from these streams at least 10 km down the axis of this valley to where it enters Boulder Basin. Alluvial deposits and rock outcrops are still exposed on large parts of the lake floor.

A bioassay for studying behavioural responses of the common bed bug, Cimex lectularius (Hemiptera: Cimicidae) to bed bug-derived volatiles.

PubMed

Weeks, E N I; Logan, J G; Gezan, S A; Woodcock, C M; Birkett, M A; Pickett, J A; Cameron, M M

2011-02-01

The common bed bug, Cimex lectularius (Hemiptera: Cimicidae), has recently re-emerged in increasing numbers, distribution and intensity of infestation in many countries. Current control relies on the application of residual pesticides; but, due to the development of insecticide resistance, there is a need for new tools and techniques. Semiochemicals (behaviour and physiology modifying chemicals) could be exploited for management of bed bugs. However, in order to identify semiochemicals that can be utilised in monitoring or control, a suitable olfactometer is needed that enables the study of the responses of bed bugs to volatile chemicals. Previous studies have used olfactometers that do not separate olfactory responses from responses to physical contact. In this study, a still-air olfactometer was used to measure behavioural responses to different bed bug-derived volatiles presented in an odour pot. Bed bugs were significantly more likely to visit the area above the odour pot first, and more frequently, in the presence of volatiles from bed bug-exposed paper but not in the presence of volatiles from conspecific bed bugs. Bed bug activity was found to be dependent on the presence of the volatiles from bed bug-exposed paper, the time during the scotophase and the sex of the insect being tested. The still-air olfactometer could be used to test putative semiochemicals, which would allow an understanding of their behavioural role in bed bug ecology. Ultimately, this could lead to the identification of new semiochemical tools for bed bug monitoring and control.

Bone regeneration in the presence of a synthetic hydroxyapatite/silica oxide-based and a xenogenic hydroxyapatite-based bone substitute material.

PubMed

Kruse, A; Jung, R E; Nicholls, F; Zwahlen, R A; Hämmerle, C H F; Weber, F E

2011-05-01

A comparison of synthetic hydroxyapatite/silica oxide, xenogenic hydroxyapatite-based bone substitute materials with empty control sites in terms of bone regeneration enhancement in a rabbit calvarial four non-critical-sized defect model. In each of six rabbits, four bicortical calvarial bone defects were generated. The following four treatment modalities were randomly allocated: (1) empty control site, (2) synthetic hydroxyapatite/silica oxide-based (HA/SiO) test granules, (3) xenogenic hydroxyapatite -based granules, (4) synthetic hydroxyapatite/silica oxide -based (HA/SiO) test two granules. The results of the latter granules have not been reported due to their size being three times bigger than the other two granule types. After 4 weeks, the animals were sacrificed and un-decalcified sections were obtained for histological analyses. For statistical analysis, the Kruskal-Wallis test was applied (P<0.05). Histomorphometric analysis showed an average area fraction of newly formed bone of 12.32±10.36% for the empty control, 17.47±6.42% for the xenogenic hydroxyapatite -based granules group, and 21.2±5.32% for the group treated with synthetic hydroxyapatite/silica oxide -based granules. Based on the middle section, newly formed bone bridged the defect to 38.33±37.55% in the empty control group, 54.33±22.12% in the xenogenic hydroxyapatite -based granules group, and to 79±13.31% in the synthetic hydroxyapatite/silica oxide -based granules group. The bone-to-bone substitute contact was 46.38±18.98% for the xenogenic and 59.86±14.92% for the synthetic hydroxyapatite/silica oxide-based granules group. No significant difference in terms of bone formation and defect bridging could be detected between the two bone substitute materials or the empty defect. There is evidence that the synthetic hydroxyapatite/silica oxide granules provide comparable results with a standard xenogenic bovine mineral in terms of bone formation and defect bridging in non-critical size defects. © 2010 John Wiley & Sons A/S.

Effect of Superficial Gas Velocity on the Solid Temperature Distribution in Gas Fluidized Beds with Heat Production

PubMed Central

2017-01-01

The hydrodynamics and heat transfer of cylindrical gas–solid fluidized beds for polyolefin production was investigated with the two-fluid model (TFM) based on the kinetic theory of granular flow (KTGF). It was found that the fluidized bed becomes more isothermal with increasing superficial gas velocity. This is mainly due to the increase of solids circulation and improvement in gas solid contact. It was also found that the average Nusselt number weakly depends on the gas velocity. The TFM results were qualitatively compared with simulation results of computational fluid dynamics combined with the discrete element model (CFD-DEM). The TFM results were in very good agreement with the CFD-DEM outcomes, so the TFM can be a reliable source for further investigations of fluidized beds especially large lab-scale reactors PMID:29187774

9 CFR 3.3 - Sheltered housing facilities.

Code of Federal Regulations, 2012 CFR

2012-01-01

... attending veterinarian. Dry bedding, solid resting boards, or other methods of conserving body heat must be... wire, wood, metal, or concrete; and (iii) All walls, boxes, houses, dens, and other surfaces in contact...

9 CFR 3.3 - Sheltered housing facilities.

Code of Federal Regulations, 2013 CFR

2013-01-01

... attending veterinarian. Dry bedding, solid resting boards, or other methods of conserving body heat must be... wire, wood, metal, or concrete; and (iii) All walls, boxes, houses, dens, and other surfaces in contact...

9 CFR 3.3 - Sheltered housing facilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

... attending veterinarian. Dry bedding, solid resting boards, or other methods of conserving body heat must be... wire, wood, metal, or concrete; and (iii) All walls, boxes, houses, dens, and other surfaces in contact...

40 CFR 60.101 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... crude oil removed from the earth and the oils derived from tar sands, shale, and coal. (c) Process gas..., or react with a contact material suspended in a fluidized bed to improve feedstock quality for...

Coastal geomorphic conditions and styles of storm surge washover deposits from Southern Thailand

NASA Astrophysics Data System (ADS)

Phantuwongraj, Sumet; Choowong, Montri; Nanayama, Futoshi; Hisada, Ken-Ichiro; Charusiri, Punya; Chutakositkanon, Vichai; Pailoplee, Santi; Chabangbon, Akkaneewut

2013-06-01

The characteristics of tropical storm washover deposits laid down during the years 2007 to 2011 along the southern peninsular coast of the Gulf of Thailand (GOT) were described in relation to their different geomorphic conditions, including perched fan, washover terrace and sheetwash lineations preserved behind the beach zone within 100 m of the shoreline. As a result, washover terrace and sheetwash lineations were found where the beach configuration was uniform and promoted an unconfined flow. Non-uniform beach configurations that promoted a confined flow resulted in a perched fan deposit. Washover sediments were differentiated into two types based on sedimentary characteristics, including (i) a thick-bedded sand of multiple reverse grading layers and (ii) a medium-bedded sand of multiple normal grading layers. In the case of thick-bedded washover deposits, the internal sedimentary structures were characterized by the presence of sub-horizontal bedding, reverse grading, lamination, foreset bedding and wavy bedding, whereas, horizontal bedding, normal grading, and dunes were the dominant structures in the medium-bedded washover sand. Rip-up clasts were rare and recognized only in the washover deposits in the bottom unit, which reflects the condition when a mud supply was available. All washover successions were found in the landward inclined-bedding with a basal sharp contact. A high elevated beach ridge associated with a large swale at the backshore proved suitable for a thick-bedded washover type, whereas a small beach ridge with uniformly flat backshore topography promoted a medium-bedded washover sediment.

Process for the production of fuel gas from coal

DOEpatents

Patel, Jitendra G.; Sandstrom, William A.; Tarman, Paul B.

1982-01-01

An improved apparatus and process for the conversion of hydrocarbonaceous materials, such as coal, to more valuable gaseous products in a fluidized bed gasification reaction and efficient withdrawal of agglomerated ash from the fluidized bed is disclosed. The improvements are obtained by introducing an oxygen containing gas into the bottom of the fluidized bed through a separate conduit positioned within the center of a nozzle adapted to agglomerate and withdraw the ash from the bottom of the fluidized bed. The conduit extends above the constricted center portion of the nozzle and preferably terminates within and does not extend from the nozzle. In addition to improving ash agglomeration and withdrawal, the present invention prevents sintering and clinkering of the ash in the fluidized bed and permits the efficient recycle of fine material recovered from the product gases by contacting the fines in the fluidized bed with the oxygen as it emanates from the conduit positioned within the withdrawal nozzle. Finally, the present method of oxygen introduction permits the efficient recycle of a portion of the product gases to the reaction zone to increase the reducing properties of the hot product gas.

Process for converting cellulosic materials into fuels and chemicals

DOEpatents

Scott, C.D.; Faison, B.D.; Davison, B.H.; Woodward, J.

1994-09-20

A process is described for converting cellulosic materials, such as waste paper, into fuels and chemicals utilizing enzymatic hydrolysis of the major constituent of paper, cellulose. A waste paper slurry is contacted by cellulase in an agitated hydrolyzer. The cellulase is produced from a continuous, columnar, fluidized-bed bioreactor utilizing immobilized microorganisms. An attrition mill and a cellobiase reactor are coupled to the agitated hydrolyzer to improve reaction efficiency. The cellulase is recycled by an adsorption process. The resulting crude sugars are converted to dilute product in a fluidized-bed bioreactor utilizing microorganisms. The dilute product is concentrated and purified by utilizing distillation and/or a biparticle fluidized-bed bioreactor system. 1 fig.

Fluidized bed gasification of extracted coal

DOEpatents

Aquino, Dolores C.; DaPrato, Philip L.; Gouker, Toby R.; Knoer, Peter

1986-01-01

Coal or similar carbonaceous solids are extracted by contacting the solids in an extraction zone (12) with an aqueous solution having a pH above 12.0 at a temperature between 65.degree. C. and 110.degree. C. for a period of time sufficient to remove bitumens from the coal into said aqueous solution and the extracted solids are then gasified at an elevated pressure and temperature in a fluidized bed gasification zone (60) wherein the density of the fluidized bed is maintained at a value above 160 kg/m.sup.3. In a preferred embodiment of the invention, water is removed from the aqueous solution in order to redeposit the extracted bitumens onto the solids prior to the gasification step.

Hydrodynamics study on drying of pepper in swirling fluidized bed dryer (SFBD)

NASA Astrophysics Data System (ADS)

Syaif Haron, Nazrul; Hazri Zakaria, Jamal; Faizal Mohideen Batcha, Mohd

2017-08-01

Malaysia is one of the pepper producer with exports quantity reaching more than 90000 tonnes between 2010 until 2016. Drying of pepper is mandatory before their export and at present, pepper was dried by sun drying to reduce cost. This conventional drying method was time consuming and may take four days during rainy season, which retards the production of pepper. This paper proposes the swirling fluidized bed drying (SFBD) method, which was known to have high mixing ability and improved solid-gas contact to shorten the drying time of products. A lab scale SFBD system was constructed to carry out this study. Hydrodynamic study was conducted for three beds loadings of 1.0 kg, 1.4 kg at a drying temperature of 90°C. The SFBD has shown excellent potential to dry the pepper with a relatively short drying time compared to the conventional method. Batch drying for the bed loads studied only took 3 hours of drying time only. It was found that bed higher bed loading of wet pepper requires longer drying time due to higher amount of moisture content in the bed. Four distinct regimes of operation were found during drying in the SFBD and these regimes offer flexibility of operation. The total bed pressure drop was relatively low during drying.

Multi-stage circulating fluidized bed syngas cooling

DOEpatents

Liu, Guohai; Vimalchand, Pannalal; Guan, Xiaofeng; Peng, WanWang

2016-10-11

A method and apparatus for cooling hot gas streams in the temperature range 800.degree. C. to 1600.degree. C. using multi-stage circulating fluid bed (CFB) coolers is disclosed. The invention relates to cooling the hot syngas from coal gasifiers in which the hot syngas entrains substances that foul, erode and corrode heat transfer surfaces upon contact in conventional coolers. The hot syngas is cooled by extracting and indirectly transferring heat to heat transfer surfaces with circulating inert solid particles in CFB syngas coolers. The CFB syngas coolers are staged to facilitate generation of steam at multiple conditions and hot boiler feed water that are necessary for power generation in an IGCC process. The multi-stage syngas cooler can include internally circulating fluid bed coolers, externally circulating fluid bed coolers and hybrid coolers that incorporate features of both internally and externally circulating fluid bed coolers. Higher process efficiencies can be realized as the invention can handle hot syngas from various types of gasifiers without the need for a less efficient precooling step.

Solution-processed ultrathin chemically derived graphene films as soft top contacts for solid-state molecular electronic junctions.

PubMed

Li, Tao; Hauptmann, Jonas Rahlf; Wei, Zhongming; Petersen, Søren; Bovet, Nicolas; Vosch, Tom; Nygård, Jesper; Hu, Wenping; Liu, Yunqi; Bjørnholm, Thomas; Nørgaard, Kasper; Laursen, Bo W

2012-03-08

A novel method using solution-processed ultrathin chemically derived graphene films as soft top contacts for the non-destructive fabrication of molecular junctions is demonstrated. We believe this protocol will greatly enrich the solid-state test beds for molecular electronics due to its low-cost, easy-processing and flexible nature. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

DECONTAMINATION OF NEUTRON-IRRADIATED REACTOR FUEL

DOEpatents

Buyers, A.G.; Rosen, F.D.; Motta, E.E.

1959-12-22

A pyrometallurgical method of decontaminating neutronirradiated reactor fuel is presented. In accordance with the invention, neutron-irradiated reactor fuel may be decontaminated by countercurrently contacting the fuel with a bed of alkali and alkaine fluorides under an inert gas atmosphere and inductively melting the fuel and tracking the resulting descending molten fuel with induction heating as it passes through the bed. By this method, a large, continually fresh surface of salt is exposed to the descending molten fuel which enhances the efficiency of the scrubbing operation.

Microwave-enhanced chemical processes

DOEpatents

Varma, R.

1990-06-19

A process is disclosed for the disposal of toxic wastes including chlorinated hydrocarbons, comprising, establishing a bed of non-metallic particulates having a high dielectric loss factor. Intimate contact of the particulates and the toxic wastes at a temperature in excess of about 400 C in the presence of microwave radiation for a time sufficient breaks the hydrocarbon chlorine bonds. Detoxification values in excess of 80 are provided and further detoxification of the bed is followed by additional disposal of toxic wastes. 1 figure.

Biofiltration of air polluted with methane at concentration levels similar to swine slurry emissions: influence of ammonium concentration.

PubMed

Veillette, Marc; Avalos Ramirez, Antonio; Heitz, Michèle

2012-01-01

An evaluation of the effect of ammonium on the performance of two up-flow inorganic packed bed biofilters treating methane was conducted. The air flow rate was set to 3.0 L min(-1) for an empty bed residence time of 6.0 min. The biofilter was fed with a methane concentration of 0.30% (v/v). The ammonium concentration in the nutrient solution was increased by small increments (from 0.01 to 0.025 gN-NH(4) (+) L(-1)) for one biofilter and by large increments of 0.05 gN-NH(4) (+) L(-1) in the other biofilter. The total concentration of nitrogen was kept constant at 0.5 gN-NH(4) (+) L(-1) throughout the experiment by balancing ammonium with nitrate. For both biofilters, the methane elimination capacity, carbon dioxide production, nitrogen bed retention and biomass content decreased with the ammonium concentration in the nutrient solution. The biofilter with smaller ammonium increments featured a higher elimination capacity and carbon dioxide production rate, which varied from 4.9 to 14.3 g m(-3) h(-1) and from 11.5 to 30 g m(-3) h(-1), respectively. Denitrification was observed as some values of the nitrate production rate were negative for ammonium concentrations below 0.2 gN-NH(4) (+) L(-1). A Michalelis-Menten-type model fitted the ammonium elimination rate and the nitrate production rate.

Control of methanol vapours in a biotrickling filter: performance analysis and experimental determination of partition coefficient.

PubMed

Avalos Ramirez, Antonio; Peter Jones, J; Heitz, Michéle

2009-02-01

Methanol vapours were treated in a biotrickling filter (BTF) packed with inert polypropylene spheres. The effects of the nitrogen concentration in the nutrient solution, the empty bed residence time (EBRT) and the methanol inlet concentration, on the BTF performance, were all examined. The elimination capacity (EC), the biomass and the carbon dioxide production rates were all increased with the rising of the nitrogen concentration and the EBRT. The EC also rose with increasing methanol inlet load (IL) when the methanol inlet concentration and the EBRT were varied, from 0.3 to 37.0 g m(-3), and from 20 to 65 s, respectively. The BTF reached its maximum EC level of 2160 g m(-3) h(-1) when it was operated at an IL level of 3700 g m(-3) h(-1). The input methanol was removed through two mechanisms: biodegradation and absorption in the liquid phase. The partition coefficient for the methanol in the BTF was determined at five EBRTs and along the packed bed. It generally followed the Henry model, having an average value of 2.64 x 10(-4)[mol L(-1)](gas)/[mol L(-1)](liquid).

Heat transfer in freeboard region of fluidized beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biyikli, S.; Tuzla, K.; Chen, J.C.

1983-10-01

This research involved the study of heat transfer and fluid mechanic characteristics around a horizontal tube in the freeboard region of fluidized beds. Heat transfer coefficients were experimetnally measured for different bed temperatures, particle sizes, gas flow rates, and tube elevations in the freeboard region of air fluidized beds at atmospheric pressure. Local heat transfer coefficients were found to vary significantly with angular position around the tube. Average heat transfer coefficients were found to decrease with increasing freeboard tube elevation and approach the values for gas convection plus radiation for any given gas velocity. For a fixed tube elevation, heatmore » transfer coefficients generally increased with increasing gas velocity and with high particle entrainment they can approach the magnitudes found for immersed tubes. Heat transfer coefficients were also found to increase with increasing bed temperature. It was concluded that this increase is partly due to increase of radiative heat transfer and partly due to change of thermal properties of the fluidizing gas and particles. To investigate the fluid mechanic behavior of gas and particles around a freeboard tube, transient particle tube contacts were measured with a special capacitance probe in room temperature experiments. The results indicated that the tube surface experiences alternating dense and lean phase contacts. Quantitative information for local characteristics was obtained from the capacitance signals and used to develop a phenomenological model for prediction of the heat transfer coefficients around freeboard tubes. The packet renewal theory was modified to account for the dense phase heat transfer and a new model was suggested for the lean phase heat transfer. Finally, an empirical freeboard heat transfer correlation was developed from functional analysis of the freeboard heat transfer data using nondimensional groups representing gas velocity and tube elevation.« less

Mathematical model and calculation of water-cooling efficiency in a film-filled cooling tower

NASA Astrophysics Data System (ADS)

Laptev, A. G.; Lapteva, E. A.

2016-10-01

Different approaches to simulation of momentum, mass, and energy transfer in packed beds are considered. The mathematical model of heat and mass transfer in a wetted packed bed for turbulent gas flow and laminar wave counter flow of the fluid film in sprinkler units of a water-cooling tower is presented. The packed bed is represented as the set of equivalent channels with correction to twisting. The idea put forward by P. Kapitsa on representation of waves on the interphase film surface as elements of the surface roughness in interaction with the gas flow is used. The temperature and moisture content profiles are found from the solution of differential equations of heat and mass transfer written for the equivalent channel with the volume heat and mass source. The equations for calculation of the average coefficients of heat emission and mass exchange in regular and irregular beds with different contact elements, as well as the expression for calculation of the average turbulent exchange coefficient are presented. The given formulas determine these coefficients for the known hydraulic resistance of the packed bed element. The results of solution of the system of equations are presented, and the water temperature profiles are shown for different sprinkler units in industrial water-cooling towers. The comparison with experimental data on thermal efficiency of the cooling tower is made; this allows one to determine the temperature of the cooled water at the output. The technical solutions on increasing the cooling tower performance by equalization of the air velocity profile at the input and creation of an additional phase contact region using irregular elements "Inzhekhim" are considered.

Coarse-grained discrete particle simulations of particle segregation in rotating fluidized beds in vortex chambers [Discrete particle simulations of particle segregation in rotating fluidized beds in vortex chambers

DOE PAGES

Verma, Vikrant; Li, Tingwen; De Wilde, Juray

2017-05-26

Vortex chambers allow the generation of rotating fluidized beds, offering high-G intensified gas-solid contact, gas-solids separation and solids-solids segregation. Focusing on binary particle mixtures and fixing the density and diameter of the heavy/large particles, transient batch CFD-coarse-grained DPM simulations were carried out with varying densities or sizes of the light/small particles to evaluate to what extent combining these three functionalities is possible within a vortex chamber of given design. Both the rate and quality of segregation were analyzed. Within a relatively wide density and size range, fast and efficient segregation takes place, with an inner and slower rotating bed ofmore » the lighter/small particles forming within the outer and faster rotating bed of the heavier/large particles. Simulations show that the contamination of the outer bed with lighter particles occurs more easily than contamination of the inner bed with heavier particles and increases with decreasing difference in size or density of the particles. Bubbling in the inner bed is observed with an inner bed of very low density or small particles. Porosity plots show that vortex chambers with a sufficient number of gas inlet slots have to be used to guarantee a uniform gas distribution and particle bed. Lastly, the flexibility of particle segregation in vortex chambers with respect to the gas flow rate is demonstrated.« less

Coarse-grained discrete particle simulations of particle segregation in rotating fluidized beds in vortex chambers [Discrete particle simulations of particle segregation in rotating fluidized beds in vortex chambers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verma, Vikrant; Li, Tingwen; De Wilde, Juray

Vortex chambers allow the generation of rotating fluidized beds, offering high-G intensified gas-solid contact, gas-solids separation and solids-solids segregation. Focusing on binary particle mixtures and fixing the density and diameter of the heavy/large particles, transient batch CFD-coarse-grained DPM simulations were carried out with varying densities or sizes of the light/small particles to evaluate to what extent combining these three functionalities is possible within a vortex chamber of given design. Both the rate and quality of segregation were analyzed. Within a relatively wide density and size range, fast and efficient segregation takes place, with an inner and slower rotating bed ofmore » the lighter/small particles forming within the outer and faster rotating bed of the heavier/large particles. Simulations show that the contamination of the outer bed with lighter particles occurs more easily than contamination of the inner bed with heavier particles and increases with decreasing difference in size or density of the particles. Bubbling in the inner bed is observed with an inner bed of very low density or small particles. Porosity plots show that vortex chambers with a sufficient number of gas inlet slots have to be used to guarantee a uniform gas distribution and particle bed. Lastly, the flexibility of particle segregation in vortex chambers with respect to the gas flow rate is demonstrated.« less

Effect of a redesigned two-wheeled container for refuse collecting on mechanical loading of low back and shoulders.

PubMed

Kuijer, P Paul F M; Hoozemans, Marco J M; Kingma, Idsart; Van Dieën, Jaap H; De Vries, Wiebe H K; Veeger, Dirk Jan; Van der Beek, Allard J; Visser, Bart; Frings-Dresen, Monique H W

2003-05-15

The objective of this study was to compare the mechanical and perceived workload when working with a redesigned two-wheeled container and working with a standard two-wheeled container for refuse collecting. The three changes in the design of the container were a displacement of the position of the centre of mass in the direction of the axis of the wheels, a slight increase in the height of the handle and a slight increase in the horizontal distance between the handle and the wheel-axis, and an increase in the diameter of the wheels. The volume of the container remained 0.240 m3. Nine refuse collectors performed some of their most frequent daily activities with both types of containers in the laboratory. Kinematics and exerted hand forces were assessed as input for detailed 3D biomechanical models of the low back and shoulder to estimate net moments at the low back and shoulders, compressive forces at the low back and contact forces at the glenohumeral joint. Also, the refuse collectors rated the ease of handling the two-wheeled containers on a five point scale. The use of the redesigned container resulted in a decrease of the exerted hand forces of 27%, decreases in the net moments at the low back and shoulders of 8% and 20%, respectively, and a decrease of 32% of the contact force at the glenohumeral joint when compared to the standard container. However, pulling an empty redesigned container on to the pavement resulted in an increase of the shoulder moment of more than 100%. No differences between container types were found for the compressive forces at the low back. Pushing and pulling with the redesigned container was rated as easier than pushing and pulling with the standard container. No differences in subjective ratings were found for the tasks of turning the container or pulling an empty container onto the pavement. It is concluded that, provided that empty containers are placed back onto the pavement as infrequently as possible, the introduction of the redesigned container could result in a reduction of the low back and shoulder load for refuse collectors.

Evaluating the effects of bedding materials and elevated platforms on contact dermatitis and plumage cleanliness of commercial broilers and on litter condition in broiler houses.

PubMed

Kaukonen, E; Norring, M; Valros, A

2017-10-01

1. Experiment 1, comparing wood shavings and ground straw bedding with peat, was performed on 7 broiler farms over two consecutive batches during the winter season. Experiment 2, assessing the effect of elevated (30 cm) platforms, was conducted in three farms replicated with 6 consecutive batches. 2. Footpad lesions were inspected at slaughter following the Welfare Quality® (WQ) assessment and official programme. Hock lesions, plumage cleanliness and litter condition were assessed using the WQ assessment. Litter height, pH, moisture and ammonia were determined. 3. Footpad condition on wood shavings appeared to be worse compared with peat using both methods of assessment and was accompanied by inferior hock skin health. WQ assessment resulted in poorer footpad and hock skin condition on ground straw compared with peat. Farms differed in footpad and hock skin condition. Footpad and hock lesions were not affected by platform treatment. Peat appeared more friable than ground straw. The initial pH of wood shavings was higher and moisture was lower than in peat, but at the end of production period there were no differences. Ground straw exhibited higher initial and lower end pH, and was drier in the beginning than peat. Litter condition and quality were not affected by platform treatment. 4. This study provides new knowledge about the applicability of peat as broiler bedding and shows no negative effects of elevated platforms on litter condition or the occurrence of contact dermatitis in commercial environments. The results suggest a complicated relationship between litter condition, moisture and contact dermatitis. Furthermore, it is concluded that the farmer's ability to manage litter conditions is important, regardless of the chosen litter material. Peat bedding was beneficial for footpad and hock skin health compared with wood shavings and ground straw.

On a criterion of incipient motion and entrainment into suspension of a particle from cuttings bed in shear flow of non-Newtonian fluid

NASA Astrophysics Data System (ADS)

Ignatenko, Yaroslav; Bocharov, Oleg; May, Roland

2017-10-01

Solids transport is a major issue in high angle wells. Bed-load forms by sediment while transport and accompanied by intermittent contact with stream-bed by rolling, sliding and bouncing. The study presents the results of a numerical simulation of a laminar steady-state flow around a particle at rest and in free motion in a shear flow of Herschel-Bulkley fluid. The simulation was performed using the OpenFOAM open-source CFD package. A criterion for particle incipient motion and entrainment into suspension from cuttings bed (Shields criteria) based on forces and torques balance is discussed. Deflection of the fluid parameters from the ones of Newtonian fluid leads to decreasing of the drag and lift forces and the hydrodynamic moment. Thus, the critical shear stress (Shields parameter) for the considered non-Newtonian fluid must be greater than the one for a Newtonian fluid.

Behavioral Responses of the Common Bed Bug, Cimex lectularius, to Insecticide Dusts.

PubMed

Agnew, John L; Romero, Alvaro

2017-08-08

Bed bugs have reemerged recently as a serious and growing problem not only in North America but in many parts of the world. These insects have become the most challenging pest to control in urban environments. Residual insecticides are the most common methods used for bed bug control; however, insecticide resistance limits the efficacy of treatments. Desiccant dusts have emerged as a good option to provide a better residual effect for bed bug control. Several studies have focused on determining the efficacy of dust-based insecticides against bed bugs. However, behavioral responses of bed bugs to insecticide dusts could influence their efficacy. The behavioral responses of bed bugs to six insecticide dusts commonly used in the United States were evaluated with an advanced video tracking technique (Ethovision). Bed bugs took longer to make first contact with areas treated with the diatomaceous earth (DE)-based products MotherEarth D and Alpine than pyrethroid, pyrethrins or silica gel based products, DeltaDust, Tempo 1% Dust and CimeXa, respectively. Lower visitation rates of bed bugs were recorded for areas treated with MotherEarth D, Alpine and CimeXa than that of DeltaDust, Tempo 1% Dust, and Tri-Die Silica + Pyrethrum Dust. Bed bugs spent less time in areas treated with Tri-Die Dust, CimeXa, Alpine, and MotherEarth D than DeltaDust and Tempo 1% Dust, and they exhibited a reduction in locomotor parameters when crawling on areas treated with CimeXa and Alpine. The implications of these responses to bed bug control are discussed.

Research on acting mechanism and behavior of a gas bubble in the air dense medium fluidized bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tao, X.; Chen, Q.; Yang, Y.

1996-12-31

Coal dry beneficiation with air-dense medium fluidized bed has now been established as a high efficiency dry separation technology, it is the application of fluidization technology to the coal preparation field. The tiny particle media forms an uniform and stable fluidized bed with a density acted by airflow, which is used to separate 80{micro}m to {approximately}6mm size coal. This technology has achieved satisfied industrialization results, and attracted the expert`s attention in the field. In fluidized bed, the interaction between gas and solid was mainly decided by the existence state of heavy media particles mass (position and distance) relative velocity ofmore » gas-solid two phase, as well turbulent action. A change of vertical gas-solid fluidizing state essentially is the one of a energy transforming process. For a coal separating process with air-dense medium fluidized bed, the gas bubble, producing a turbulent and stirring action in the bed, leads to two effects. It can promote a uniform distribution of heavy media particles, and a uniform and stability of a bed density. Otherwise it will decrease effective contacts between gas-solids two phases, producing a bigger gas bubble. Therefore controlling a gas bubble size in bed should be optimized. This paper analyzes mutual movement between gas-solid, and studies the gas bubble behavior in the bed. A mechanic mode and a separating process of coal in the bed is discussed. It aims to research the coal separating mechanism with air-dense fluidized bed.« less

Behavioral Responses of the Common Bed Bug, Cimex lectularius, to Insecticide Dusts

PubMed Central

Agnew, John L.; Romero, Alvaro

2017-01-01

Bed bugs have reemerged recently as a serious and growing problem not only in North America but in many parts of the world. These insects have become the most challenging pest to control in urban environments. Residual insecticides are the most common methods used for bed bug control; however, insecticide resistance limits the efficacy of treatments. Desiccant dusts have emerged as a good option to provide a better residual effect for bed bug control. Several studies have focused on determining the efficacy of dust-based insecticides against bed bugs. However, behavioral responses of bed bugs to insecticide dusts could influence their efficacy. The behavioral responses of bed bugs to six insecticide dusts commonly used in the United States were evaluated with an advanced video tracking technique (Ethovision). Bed bugs took longer to make first contact with areas treated with the diatomaceous earth (DE)-based products MotherEarth D and Alpine than pyrethroid, pyrethrins or silica gel based products, DeltaDust, Tempo 1% Dust and CimeXa, respectively. Lower visitation rates of bed bugs were recorded for areas treated with MotherEarth D, Alpine and CimeXa than that of DeltaDust, Tempo 1% Dust, and Tri-Die Silica + Pyrethrum Dust. Bed bugs spent less time in areas treated with Tri-Die Dust, CimeXa, Alpine, and MotherEarth D than DeltaDust and Tempo 1% Dust, and they exhibited a reduction in locomotor parameters when crawling on areas treated with CimeXa and Alpine. The implications of these responses to bed bug control are discussed. PMID:28786920

Research on coal-water fuel combustion in a circulating fluidized bed / Badanie spalania zawiesinowych paliw węglowo-wodnych w cyrkulacyjnej warstwie fluidalnej

NASA Astrophysics Data System (ADS)

Kijo-Kleczkowska, Agnieszka

2012-10-01

In the paper the problem of heavily-watered fuel combustion has been undertaken as the requirements of qualitative coals combusted in power stations have been growing. Coal mines that want to fulfill expectations of power engineers have been forced to extend and modernize the coal enrichment plants. This causes growing quantity of waste materials that arise during the process of wet coal enrichment containing smaller and smaller under-grains. In this situation the idea of combustion of transported waste materials, for example in a hydraulic way to the nearby power stations appears attractive because of a possible elimination of the necessary deep dehydration and drying as well as because of elimination of the finest coal fraction loss arising during discharging of silted water from coal wet cleaning plants. The paper presents experimental research results, analyzing the process of combustion of coal-water suspension depending on the process conditions. Combustion of coal-water suspensions in fluidized beds meets very well the difficult conditions, which should be obtained to use the examined fuel efficiently and ecologically. The suitable construction of the research stand enables recognition of the mechanism of coal-water suspension contact with the inert material, that affects the fluidized bed. The form of this contact determines conditions of heat and mass exchange, which influence the course of a combustion process. The specificity of coal-water fuel combustion in a fluidized bed changes mechanism and kinetics of the process.

Suspension system for a wheel rolling on a flat track. [bearings for directional antennas

NASA Technical Reports Server (NTRS)

Mcginness, H. D. (Inventor)

1981-01-01

An improved suspension system for an uncrowned wheel rolling on a flat track is presented. It is characterized by a wheel frame assembly including a wheel frame and at least one uncrowned wheel connected in supporting relation with the frame. It is adapted to be seated in rolling engagement with a flat track, a load supporting bed, and a plurality of flexural struts interconnecting the bed in supported relation with the frame. Each of said struts is disposed in a plane passing through the center of the uncrowned wheel surface along a line substantially bisecting the line of contact established between the wheel surface and the flat surface of the truck and characterized by a modulus of elasticity sufficient for maintaining the axis of rotation for the wheel in substantial parallelism with the line of contact established between the surfaces of the wheel and track.

Contact radiator burn subsequent to spinal anaesthesia.

PubMed

Sever, C; Aysal, B K; Sahin, C; Kulahci, Y

2012-06-30

An unusual case is reported in which a patient sustained a third-degree burn of the plantar surface of the right foot as the result of contact with a heating radiator. This occurred when the patient fell asleep in his hospital bed after knee surgery. Spinal anaesthesia is easy to perform, and the risk factors, though present, are not serious. Such accidents are not infrequent and care should be taken to prevent them.

Contact radiator burn subsequent to spinal anaesthesia

PubMed Central

Sever, C.; Aysal, B.K.; Sahin, C.; Kulahci, Y.

2012-01-01

Summary An unusual case is reported in which a patient sustained a third-degree burn of the plantar surface of the right foot as the result of contact with a heating radiator. This occurred when the patient fell asleep in his hospital bed after knee surgery. Spinal anaesthesia is easy to perform, and the risk factors, though present, are not serious. Such accidents are not infrequent and care should be taken to prevent them. PMID:23233830

Nitric Oxide Reduction over Sewage Sludge and Coal Chars at Conditions Relevant to Staged Fluidized Bed Combustion

NASA Astrophysics Data System (ADS)

Salatino, P.; Solimene, R.; Chirone, R.

The de-NOx potential of coal and of dried and pelletized sewage sludge, a waste-derived fuel candidate for cofiring with coal, is assessed. The experimental procedure is based on operation of a bench scale fluidized bed reactor where NO-doped nitrogen is contacted with batches of the fuel. A second type of experiment has been purposely designed to assess the loss of reactivity of chars toward gasification by NOx as char is heat-treated for pre-set times at temperatures typical of fluidized bed combustion. A simple phenomenological model is developed to shed light on the basic features of the interaction between heterogeneous char-NOx reaction and thermal annealing of the char.

Fluidized bed gasification of extracted coal

DOEpatents

Aquino, D.C.; DaPrato, P.L.; Gouker, T.R.; Knoer, P.

1984-07-06

Coal or similar carbonaceous solids are extracted by contacting the solids in an extraction zone with an aqueous solution having a pH above 12.0 at a temperature between 65/sup 0/C and 110/sup 0/C for a period of time sufficient to remove bitumens from the coal into said aqueous solution, and the extracted solids are then gasified at an elevated pressure and temperature in a fluidized bed gasification zone (60) wherein the density of the fluidized bed is maintained at a value above 160 kg/m/sup 3/. In a preferred embodiment of the invention, water is removed from the aqueous solution in order to redeposit the extracted bitumens onto the solids prior to the gasification step. 2 figs., 1 tab.

Binge-eating disorder in the Swedish national registers: Somatic comorbidity.

PubMed

Thornton, Laura M; Watson, Hunna J; Jangmo, Andreas; Welch, Elisabeth; Wiklund, Camilla; von Hausswolff-Juhlin, Yvonne; Norring, Claes; Herman, Barry K; Larsson, Henrik; Bulik, Cynthia M

2017-01-01

To evaluate associations between binge-eating disorder (BED) and somatic illnesses and determine whether medical comorbidities are more common in individuals who present with BED and comorbid obesity. Cases (n = 850) were individuals with a BED diagnosis in the Swedish eating disorders quality registers. Ten community controls were matched to each case on sex, and year, month, and county of birth. Associations of BED status with neurologic, immune, respiratory, gastrointestinal, skin, musculoskeletal, genitourinary, circulatory, and endocrine system diseases were evaluated using conditional logistic regression models. We further examined these associations by adjusting for lifetime psychiatric comorbidity. Amongst individuals with BED, we explored whether comorbid obesity was associated with risk of somatic disorders. BED was associated with most classes of diseases evaluated; strongest associations were with diabetes [odds ratio (95% confidence interval) = 5.7 (3.8; 8.7)] and circulatory systems [1.9 (1.3; 2.7)], likely indexing components of metabolic syndrome. Amongst individuals with BED, those with comorbid obesity were more likely to have a lifetime history of respiratory [1.5 (1.1; 2.1)] and gastrointestinal [2.6 (1.7; 4.1)] diseases than those without comorbid obesity. Increased risk of some somatic disease classes in individuals with BED was not simply due to obesity or other lifetime psychiatric comorbidity. The association of BED with many somatic illnesses highlights the morbidity experienced by individuals with BED. Clinicians treating patients with BED should be vigilant for medical comorbidities. Nonpsychiatric providers may be the first clinical contact for those with BED underscoring the importance of screening in primary care. © 2016 The Authors International Journal of Eating Disorders Published by Wiley Periodicals, Inc. (Int J Eat Disord 2017; 50:58-65). © 2016 The Authors International Journal of Eating Disorders Published by Wiley Periodicals, Inc.

A lattice model for influenza spreading.

PubMed

Liccardo, Antonella; Fierro, Annalisa

2013-01-01

We construct a stochastic SIR model for influenza spreading on a D-dimensional lattice, which represents the dynamic contact network of individuals. An age distributed population is placed on the lattice and moves on it. The displacement from a site to a nearest neighbor empty site, allows individuals to change the number and identities of their contacts. The dynamics on the lattice is governed by an attractive interaction between individuals belonging to the same age-class. The parameters, which regulate the pattern dynamics, are fixed fitting the data on the age-dependent daily contact numbers, furnished by the Polymod survey. A simple SIR transmission model with a nearest neighbors interaction and some very basic adaptive mobility restrictions complete the model. The model is validated against the age-distributed Italian epidemiological data for the influenza A(H1N1) during the [Formula: see text] season, with sensible predictions for the epidemiological parameters. For an appropriate topology of the lattice, we find that, whenever the accordance between the contact patterns of the model and the Polymod data is satisfactory, there is a good agreement between the numerical and the experimental epidemiological data. This result shows how rich is the information encoded in the average contact patterns of individuals, with respect to the analysis of the epidemic spreading of an infectious disease.

Genesis of a regionally widespread celadonitic chert ironstone bed overlying upper Lias manganese deposits, Hungary

USGS Publications Warehouse

Polgari, Marta; Hein, J.R.; Toth, M.; Brukner-Wein, A.; Vigh, T.; Biro, L.; Cserhati, C.

2010-01-01

Mineralogy and chemical composition are presented for a chert-ironstone bed that overlies the ??rk??t Mn deposit. This bed is mottled green-brown in its lower and upper parts, which are composed of quartz, goethite and celadonite. These parts of the bed are interpreted to be strongly altered tuffs, reflecting oxidic, low-temperature alteration of a hydrated, Fe-rich, Al-poor tuff, and K and Mg uptake from seawater. The middle part of the bed is a mineralized bacterial mat (quartz, goethite). Textures resembling bacterial cells and colonies are common, with wavy, bulbous laminations composed of mounds overlying a mesh-work stromatolite-like texture constructed of micrometre-size Fe oxides. This bed is concordant with the underlying Mn deposit and marks the termination of Mn accumulation. Although no genetic connection exists between the two, the rocks adjacent to the contact record the oceanographic and bottom-water conditions extant when accumulation of one of the major Mn deposits of Europe ended, when the Transdanubian Range was located in the middle of the Adria-Apulian microcontinent between the Neotethys and Atlantic-Ligurian seaways. A pyroclastic origin for part of the bed has significance for the Toarcian of Central Europe because evidence of volcanism occurring at that time is otherwise sparse. ?? 2010 Geological Society of London.

Hydrogeologic reconnaissance of the San Miguel River basin, southwestern Colorado

USGS Publications Warehouse

Ackerman, D.J.; Rush, F.E.

1984-01-01

The San Miguel River Basin encompasses 4,130 square kilometers of which about two-thirds is in the southeastern part of the Paradox Basin. The Paradox Basin is a part of the Colorado Plateaus that is underlain by a thick sequence of evaporite beds of Pennsylvanian age. The rock units that underlie the area have been grouped into hydrogeologic units based on their water-transmitting ability. Evaporite beds of mostly salt are both overlain and underlain by confining beds. Aquifers are present above and below the confining-bed sequence. The principal element of ground-water outflow from the upper aquifer is flow to the San Miguel River and its tributaries; this averages about 90 million cubic meters per year. A water budget for the lower aquifer has only two equal, unestimated elements, subsurface outflow and recharge from precipitation. The aquifers are generally isolated from the evaporite beds by the bounding confining beds; as a result, most ground water has little if any contact with the evaporites. No brines have been sampled and no brine discharges have been identified in the basin. Salt water has been reported for petroleum-exploration wells, but no active salt solution has been identified. (USGS)

Effects of bovine lactoferrin in surgically created bone defects on bone regeneration around implants.

PubMed

Görmez, Ulaş; Kürkcü, Mehmet; E Benlidayi, Mehmet; Ulubayram, Kezban; Sertdemir, Yaşar; Dağlioğlu, Kenan

2015-03-01

The aim of this experimental study was to evaluate the effect of bovine lactoferrin (bLF)-loaded gelatin microspheres (GM) used in combination with anorganic bovine bone on bone regeneration in surgically created bone defects around tooth implants. Twenty-four uniform bone defects were created in the frontal bone via an extraoral approach in 12 domestic pigs. Twenty-four implants were placed at the center of the defects. In eight animals one of these defects was filled with 0.3 mL anorganic bovine bone while the other was left empty. In four animals, all defects were filled with 3 mg/defect bLF-loaded GM and anorganic bovine bone. All the defects were covered with collagen membranes. All animals were sacrificed after 10 weeks of healing, and the implants with the surrounding bone defects were removed en bloc. Undecalcified sections were prepared for histomorphometric analysis. The mean total area of hard tissue was 26.9 ± 6.0% in the empty defect group, 31.8 ± 8.4% in the graft group, and 47.6 ± 5.0% in the lactoferrin group (P < 0.001). The mean area of newly formed bone was 26.9 ± 6.0% in the empty defect group, 22.4 ± 8.2% in the graft group, and 46.1 ± 5.1% in the lactoferrin group (P < 0.001). The mean residual graft area was 9.4 ± 3.2% in the graft group and 1.5 ± 0.6% in the lactoferrin group (P < 0.001). The mean proportion of bone-implant contact in the defect region was 21.9 ± 8.4% in the empty defect group, 26.9 ± 10.1% in the graft group and 29.9 ± 10.3% in the lactoferrin group (P = 0.143). These data indicate that a combination of 3 mg bLF-loaded GM and bovine-derived HA promotes bone regeneration in defects around implants.

Effect of granular media on the vibrational response of a resonant structure: theory and experiment.

PubMed

Valenza, John J; Hsu, Chaur-Jian; Johnson, David Linton

2010-11-01

The acoustic response of a structure that contains a cavity filled with a loose granular material is analyzed. The inputs to the theory are the effective masses of each subsystem: that of the empty-cavity resonating structure and that of the granular medium within the cavity. This theory accurately predicts the frequencies, widths, and relative amplitudes of the various flexural mode resonances observed with rectangular bars, each having a cavity filled with loose tungsten granules. Inasmuch as the dominant mechanism for damping is due to adsorbed water at the grain-grain contacts, the significant effects of humidity on both the effective mass of the granular medium as well as on the response of the grain-loaded bars are monitored. Here, depending upon the humidity and the preparation protocol, it is possible to observe one, two, or three distinct resonances in a wide frequency range (1-5 kHz) over which the empty bar has but one resonance. These effects are understood in terms of the theoretical framework, which may simplify in terms of perturbation theories.

Experimental study of cassava sun drying

DOE Office of Scientific and Technical Information (OSTI.GOV)

Njie, D.N.; Rumsey, T.R.

1997-03-01

Sun drying experiments were performed to compare drying of cassava chips in sheet-metal trays with drying on mesh wire trays. In the sheet-metal trays, there was air flow across the top of the bed chips, while the mesh wire trays permitted air to flow through the bed. Drying rate was faster and more uniform in the trays with through-flow air circulation. Higher temperatures were reached by chips in the sheet-metal trays than those in the mesh trays because of contact heating, but the drying rate was lower because of the reduced air flow.

Removal of disinfection byproduct (DBP) precursors in water by two-stage biofiltration treatment.

PubMed

Fu, Jie; Lee, Wan-Ning; Coleman, Clark; Nowack, Kirk; Carter, Jason; Huang, Ching-Hua

2017-10-15

The removal of precursors of 36 disinfection byproducts (DBPs) in effluents from flocculation/sedimentation process was evaluated across a pilot-scale two-stage biofiltration process, i.e., a sand/anthracite (SA) biofilter (empty bed contact time (EBCT) of 7.5 min) coupled with a biologically-active granular activated carbon (GAC) contactor (EBCT of 15 min). The biofiltration process exhibited a good capacity for removal of the total DBP formation potential (DBPFP) (by 25.90 ± 2.63%), and GAC contactors contributed most to the DBPFP removal (accounting for 60.63 ± 16.64% of the total removal). The removal percentage of DBPFPs of different structure types was in the following order: halonitroalkanes (58.50%) > haloaldehydes (33.62%) > haloacetic acids (HAAs, 28.13%) > haloalkanes (20.46%) > haloketones (13.46%) > nitrosamines (10.23%) > halonitriles (-8.82%) > haloalkenes (-9.84%). The precursors of bromo-DBPs (containing only bromine atoms) and maximal halogenated DBPs (containing 3 & 4 halo atoms) were removed largely compared to other DBPs. Among the total DBPFP, trihalomethanes (THMs), HAAs, and chloral hydrate were the dominant DBPs, and they accounted for >92% of the total targeted DBPs by weight. Pearson correlation analysis (CA) and principal components analysis (PCA) indicated a significant association among these dominant DBPs. Canonical correspondence analysis (CCA) revealed specific ultraviolet absorbance (SUVA 254 ) could serve as a good surrogate parameter for DBPFP. Pre-chlorination upstream of the biofilters may not greatly impact the overall removal of DBPFP by SA/GAC biofiltration. In addition, results showed that SA/GAC biofiltration was a useful procedure to remove the inorganic DBP chlorite. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biologically active filters - An advanced water treatment process for contaminants of emerging concern.

PubMed

Zhang, Shuangyi; Gitungo, Stephen W; Axe, Lisa; Raczko, Robert F; Dyksen, John E

2017-05-01

With the increasing concern of contaminants of emerging concern (CECs) in source water, this study examines the hypothesis that existing filters in water treatment plants can be converted to biologically active filters (BAFs) to treat these compounds. Removals through bench-scale BAFs were evaluated as a function of media, granular activated carbon (GAC) and dual media, empty bed contact time (EBCT), and pre-ozonation. For GAC BAFs, greater oxygen consumption, increased pH drop, and greater dissolved organic carbon removal normalized to adenosine triphosphate (ATP) were observed indicating increased microbial activity as compared to anthracite/sand dual media BAFs. ATP concentrations in the upper portion of the BAFs were as much as four times greater than the middle and lower portions of the dual media and 1.5 times greater in GAC. Sixteen CECs were spiked in the source water. At an EBCT of 18 min (min), GAC BAFs were highly effective with overall removals greater than 80% without pre-ozonation; exceptions included tri(2-chloroethyl) phosphate and iopromide. With a 10 min EBCT, the degree of CECs removal was reduced with less than half of the compounds removed at greater than 80%. The dual media BAFs showed limited CECs removal with only four compounds removed at greater than 80%, and 10 compounds were reduced by less than 50% with either EBCT. This study demonstrated that GAC BAFs with and without pre-ozonation are an effective and advanced technology for treating emerging contaminants. On the other hand, pre-ozonation is needed for dual media BAFs to remove CECs. The most cost effective operating conditions for dual media BAFs were a 10 min EBCT with the application of pre-ozonation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Identifying the limitations of conventional biofiltration of diffuse methane emissions at long-term operation.

PubMed

Gómez-Cuervo, S; Hernández, J; Omil, F

2016-08-01

There is growing international concern about the increasing levels of greenhouse gases in the atmosphere, particularly CO2 and methane. The emissions of methane derived from human activities are associated with large flows and very low concentrations, such as those emitted from landfills and wastewater treatment plants, among others. The present work was focused on the biological methane degradation at diffuse concentrations (0.2% vv(-1)) in a conventional biofilter using a mixture of compost, perlite and bark chips as carrier. An extensive characterization of the process was carried out at long-term operation (250 days) in a fully monitored pilot plant, achieving stable conditions during the entire period. Operational parameters such as waterings, nitrogen addition and inlet loads and contact time influences were evaluated. Obtained results indicate that empty bed residence times within 4-8 min are crucial to maximize elimination rates. Waterings and the type of nitrogen supplied in the nutrient solution (ammonia or nitrate) have a strong impact on the biofilter performance. The better results compatible with a stable operation were achieved using nitrate, with elimination capacities up to 7.6 ± 1.1 g CH4 m(-3 )h(-1). The operation at low inlet concentrations (IC) implied that removal rates obtained were quite limited (ranging 3-8 g CH4 m(-3 )h(-1)); however, these results could be significantly increased (up to 20.6 g CH4 m(-3) h(-1)) at higher IC, which indicates that the mass transfer from the gas to the liquid layer surrounding the biofilm is a key limitation of the process.

Transformation of Nitrate and Toluene in Groundwater by Sulfur Modified Iron(SMI-III)

NASA Astrophysics Data System (ADS)

Lee, W.; Park, S.; Lim, J.; Hong, U.; Kwon, S.; Kim, Y.

2009-12-01

In Korea, nitrate and benzene, toluene, ethylbenzene, and xylene isomers (BTEX) are frequently detected together as ground water contaminants. Therefore, a system simultaneously treating both nitrate (inorganic compound) and BTEX (organic compounds) is required to utilize groundwater as a water resource. In this study, we investigated the efficiency of Sulfur Modified Iron (SMI-III) in treating both nitrate and BTEX contaminated groundwater. Based on XRD (X-Ray Diffraction) analysis, the SMI-III is mainly composed of Fe3O4, S, and Fe. A series of column tests were conducted at three different empty bed contact times (EBCTs) for each compound. During the experiments, removal efficiency for both nitrate and toluene were linearly correlated with EBCT, suggesting that SMI-III have an ability to transform both nitrate and toluene. The concentration of SO42- and oxidation/reduction potential (ORP) were also measured. After exposed to nitrate contaminated groundwater, the composition of SMI-III was changed to Fe2O3, Fe3O4, Fe, and Fe0.95S1.05. The trends of effluent sulfate concentrations were inversely correlated with effluent nitrate concentrations, while the trends of ORP values, having the minimum values of -480 mV, were highly correlated with effluent nitrate concentrations. XRD analysis before and after exposed to nitrate contaminated groundwater, sulfate production, and nitrite detection as a reductive transformation by-product of nitrate suggest that nitrate is reductively transformed by SMI-III. Interestingly, in the toluene experiments, the trends of ORP values were inversely correlated with effluent toluene concentrations, suggesting that probably degrade through oxidation reaction. Consequently, nitrate and toluene probably degrade through reduction and oxidation reaction, respectively and SMI-III could serve as both electron donor and acceptor.

16 CFR Figure 3 to Part 1513 - Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of “A” Section of Probe and...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of âAâ Section of Probe and Boundaries of Opening 3 Figure 3 to Part 1513... REQUIREMENTS FOR BUNK BEDS Pt. 1513, Fig. 3 Figure 3 to Part 1513—Motion of Test Probe Arrested by Simultaneous...

16 CFR Figure 3 to Part 1513 - Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of “A” Section of Probe and...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of âAâ Section of Probe and Boundaries of Opening 3 Figure 3 to Part 1513... REQUIREMENTS FOR BUNK BEDS Pt. 1513, Fig. 3 Figure 3 to Part 1513—Motion of Test Probe Arrested by Simultaneous...

16 CFR Figure 3 to Part 1513 - Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of “A” Section of Probe and...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of âAâ Section of Probe and Boundaries of Opening 3 Figure 3 to Part 1513... REQUIREMENTS FOR BUNK BEDS Pt. 1513, Fig. 3 Figure 3 to Part 1513—Motion of Test Probe Arrested by Simultaneous...

16 CFR Figure 3 to Part 1513 - Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of “A” Section of Probe and...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of âAâ Section of Probe and Boundaries of Opening 3 Figure 3 to Part 1513... REQUIREMENTS FOR BUNK BEDS Pt. 1513, Fig. 3 Figure 3 to Part 1513—Motion of Test Probe Arrested by Simultaneous...

16 CFR Figure 3 to Part 1513 - Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of “A” Section of Probe and...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Motion of Test Probe Arrested by Simultaneous Contact With Both Sides of âAâ Section of Probe and Boundaries of Opening 3 Figure 3 to Part 1513... REQUIREMENTS FOR BUNK BEDS Pt. 1513, Fig. 3 Figure 3 to Part 1513—Motion of Test Probe Arrested by Simultaneous...

Dermatologic infestations.

PubMed

Shmidt, Eugenia; Levitt, Jacob

2012-02-01

Head lice are transmitted by head to head contact. Optimal therapy includes malathion lotion 0.5% repeated in one week left on for 30 minutes to 8 hours. Spinosad topical suspension 0.9% repeated in one week left on for 10 minutes is another option. Scabies is transmitted mainly by direct contact but also via heavily infested fomites due to crusted scabies. Permethrin 5% cream to the body repeated in four days is often sufficient; however, scalp treatment with malathion lotion 0.5% is helpful in crusted scabies and in infested children. Oral ivermectin 200 mcg/kg is another option, repeated in four days. For scabies more than lice, fomites should be placed in a drier at 60 °C for 10 minutes to kill the arthropods. Treatment of close contacts in both cases will control outbreaks and repeated infestations. Both have been associated with methicillin-resistant Staphylococcus aureus infection. Bed bugs are a common cause for papular urticaria. Identification of the insect in the mattress or bedding confirms the diagnosis. Prevention involves encasing the mattress in a sealed plastic cover and extermination. Delusions of parasitosis is a diagnosis of exclusion that is best treated with an antipsychotic. © 2012 The International Society of Dermatology.

Variations in Grain-Scale Sediment Structure in a Gravel-Bed Channel as a Function of Fine Sediment Content and Morphological Location

NASA Astrophysics Data System (ADS)

Voepel, H.; Ahmed, S. I.; Hodge, R. A.; Leyland, J.; Sear, D. A.

2016-12-01

One of the major causes of uncertainty in estimates of bedload transport rates in gravel bed rivers is a lack of understanding of grain-scale sediment structure, and the impact that this structure has on bed stability. Furthermore, grain-scale structure varies throughout a channel and over time in ways that have not been fully quantified. Our research aims to quantify variations in sediment structure caused by two key variables; morphological location within a riffle-pool sequence (reflecting variation in hydraulic conditions), and the fine sediment content of the gravel bed (sand and clay). We report results from a series of flume experiments in which we water-worked a gravel bed with a riffle-pool morphology. The fine sediment content of the bed was incrementally increased over a series of runs from gravel only, to coarse sand, fine sand and two concentrations of clay. After each experimental run intact samples of the bed at different locations were extracted and the internal structure of the bed was measured using non-destructive, micro-focus X-ray computed tomography (CT) imaging. The CT images were processed to measure the properties of individual grains, including volume, center of mass, dimension, and contact points. From these data we were able to quantify the sediment structure through metrics including measurement of grain pivot angles, grain exposure and protrusion, and vertical variation in bed porosity and fine sediment content. Metrics derived from the CT data were verified using data from grain counts and tilt-table measurements on co-located samples. Comparison of the metrics across different morphological locations and fine sediment content demonstrates how these factors affect the bed structure. These results have implications for the development of sediment entrainment models for gravel bed rivers.

Comparisons of Derived Metrics from Computed Tomography (CT) Scanned Images of Fluvial Sediment from Gravel-Bed Flume Experiments

NASA Astrophysics Data System (ADS)

Voepel, Hal; Ahmed, Sharif; Hodge, Rebecca; Leyland, Julian; Sear, David

2016-04-01

Uncertainty in bedload estimates for gravel bed rivers is largely driven by our inability to characterize arrangement, orientation and resultant forces of fluvial sediment in river beds. Water working of grains leads to structural differences between areas of the bed through particle sorting, packing, imbrication, mortaring and degree of bed armoring. In this study, non-destructive, micro-focus X-ray computed tomography (CT) imaging in 3D is used to visualize, quantify and assess the internal geometry of sections of a flume bed that have been extracted keeping their fabric intact. Flume experiments were conducted at 1:1 scaling of our prototype river. From the volume, center of mass, points of contact, and protrusion of individual grains derived from 3D scan data we estimate 3D static force properties at the grain-scale such as pivoting angles, buoyancy and gravity forces, and local grain exposure. Here metrics are derived for images from two flume experiments: one with a bed of coarse grains (>4mm) and the other where sand and clay were incorporated into the coarse flume bed. In addition to deriving force networks, comparison of metrics such as critical shear stress, pivot angles, grain distributions, principle axis orientation, and pore space over depth are made. This is the first time bed stability has been studied in 3D using CT scanned images of sediment from the bed surface to depths well into the subsurface. The derived metrics, inter-granular relationships and characterization of bed structures will lead to improved bedload estimates with reduced uncertainty, as well as improved understanding of relationships between sediment structure, grain size distribution and channel topography.

Simple combination of oxidants with zero-valent-iron (ZVI) achieved very rapid and highly efficient removal of heavy metals from water.

PubMed

Guo, Xuejun; Yang, Zhe; Dong, Haiyang; Guan, Xiaohong; Ren, Qidong; Lv, Xiaofang; Jin, Xin

2016-01-01

This study, for the first time, demonstrated a continuously accelerated Fe(0) corrosion driven by common oxidants (i.e., NaClO, KMnO4 or H2O2) and thereby the rapid and efficient removal of heavy metals (HMs) by zero-valent iron (ZVI) under the experimental conditions of jar tests and column running. ZVI simply coupled with NaClO, KMnO4 or H2O2 (0.5 mM) resulted in almost complete As(V) removal within only 10 min with 1000 μg/L of initial As(V) at initial pH of 7.5(±0.1) and liquid solid ratio of 200:1. Simultaneous removal of 200 μg/L of initial Cd(II) and Hg(II) to 2.4-4.4 μg/L for Cd(II) and to 4.0-5.0 μg/L for Hg(II) were achieved within 30 min. No deterioration of HM removal was observed during the ten recycles of jar tests. The ZVI columns activated by 0.1 mM of oxidants had stably treated 40,200 (NaClO), 20,295 (KMnO4) and 40,200 (H2O2) bed volumes (BV) of HM-contaminated drinking water, but with no any indication of As breakthrough (<10 μg/L) even at short empty bed contact time (EBCT) of 8.0 min. The high efficiency of HMs removal from both the jar tests and column running implied a continuous and stable activation (overcoming of iron passivation) of Fe(0) surface by the oxidants. Via the proper increase in oxidant dosing, the ZVI/oxidant combination was applicable to treat highly As(V)-contaminated wastewater. During Fe(0) surface corrosion accelerated by oxidants, a large amount of fresh and reactive iron oxides and oxyhydroxides were continuously generated, which were responsible for the rapid and efficient removal of HMs through multiple mechanisms including adsorption and co-precipitation. A steady state of Fe(0) surface activation and HM removal enabled this simply coupled system to remove HMs with high speed, efficiency and perdurability. Copyright © 2015 Elsevier Ltd. All rights reserved.

Proximal and Overall Gastric Emptying of Solids in Patients with Reduced Gastric Volume Accommodation Compared to Matched Controls

PubMed Central

Camilleri, Michael; Breen, Mary; Ryks, Michael; Burton, Duane

2011-01-01

Background Interventions such as gastric surgery and erythromycin result in displacement of solids to the distal stomach and acceleration of overall and proximal gastric emptying. The effect of non-surgical impairment of gastric accommodation on gastric emptying is unclear. Non-surgical impairment of gastric accommodation is associated with accelerated gastric emptying. Aim To compare measurements of proximal and overall gastric emptying in patients with reduced postprandial gastric volume accommodation with the emptying rates in age- and gender-matched controls with normal postprandial gastric volume accommodation. Methods We evaluated overall and proximal gastric emptying in 9 patients with impaired gastric accommodation and age-equivalent and gender-matched controls. Gastric volumes and emptying were measured using validated SPECT and dual gamma camera scintigraphy respectively. We compared group differences in overall and proximal gastric emptying t1/2 by t test. Results Patients with impaired postprandial gastric volume accommodation had greater fasting gastric volume. The proportion of food emptied from the proximal stomach immediately after meal ingestion was lower and t1/2of proximal gastric emptying correspondingly longer in the group with reduced postprandial gastric accommodation. In contrast, differences were not detected in overall gastric emptying in the two groups, and the ratio of overall to proximal gastric emptying t1/2was greater in the group with impaired volume accommodation. Conclusions Proximal stomach emptying is reduced in patients with impaired postprandial volume accommodation; this difference occurs predominantly during the time of meal ingestion. Compensatory mechanisms that result in normal overall gastric emptying require further elucidation. PMID:21327917

Human-facilitated metapopulation dynamics in an emerging pest species, Cimex lectularius

PubMed Central

FOUNTAIN, TOBY; DUVAUX, LUDOVIC; HORSBURGH, GAVIN; REINHARDT, KLAUS; BUTLIN, ROGER K

2014-01-01

The number and demographic history of colonists can have dramatic consequences for the way in which genetic diversity is distributed and maintained in a metapopulation. The bed bug (Cimex lectularius) is a re-emerging pest species whose close association with humans has led to frequent local extinction and colonization, that is, to metapopulation dynamics. Pest control limits the lifespan of subpopulations, causing frequent local extinctions, and human-facilitated dispersal allows the colonization of empty patches. Founder events often result in drastic reductions in diversity and an increased influence of genetic drift. Coupled with restricted migration, this can lead to rapid population differentiation. We therefore predicted strong population structuring. Here, using 21 newly characterized microsatellite markers and approximate Bayesian computation (ABC), we investigate simplified versions of two classical models of metapopulation dynamics, in a coalescent framework, to estimate the number and genetic composition of founders in the common bed bug. We found very limited diversity within infestations but high degrees of structuring across the city of London, with extreme levels of genetic differentiation between infestations (FST = 0.59). ABC results suggest a common origin of all founders of a given subpopulation and that the numbers of colonists were low, implying that even a single mated female is enough to found a new infestation successfully. These patterns of colonization are close to the predictions of the propagule pool model, where all founders originate from the same parental infestation. These results show that aspects of metapopulation dynamics can be captured in simple models and provide insights that are valuable for the future targeted control of bed bug infestations. PMID:24446663

Evidence-based practice: use of the ventilator bundle to prevent ventilator-associated pneumonia.

PubMed

Tolentino-DelosReyes, Arlene F; Ruppert, Susan D; Shiao, Shyang-Yun Pamela K

2007-01-01

To examine critical care nurses' knowledge about the use of the ventilator bundle to prevent ventilator-associated pneumonia. Published reports were reviewed for current evidence on the use of the ventilator bundle to prevent ventilator-associated pneumonia, and education sessions were held to present the findings to 61 nurses in coronary care and surgical intensive care units. Changes in the nurses' knowledge were evaluated by using a 10-item test, given both before and after the sessions. Changes in the nurses' practices related to ventilator-associated pneumonia, including elevation of the head of the bed to 30 degrees to 45 degrees , were observed in 99 intubated patients. After the education sessions, the nurses performed better on 8 of the 10 items tested (P from .03 to <.001). The areas of most significant improvement were elevation of the head of the bed (P < .001), charting of the elevation of the head of the bed (P= .009), oral care (P= .009), checking of the nasogastric tube for residual volume (P = .008), washing of hands before contact with patients (P < .001), and limiting the wearing of rings (P < .001) and nail polish (P = .04). Even after the education sessions, the nurses' compliance with hand-washing recommendations before contact with patients was low, though statistically some improvement was apparent. Contraindications to elevation of the head of the bed did not appear to affect the nurses' practices (P= .38). Education sessions designed to inform nurses about the ventilator bundle and its use to prevent ventilator-associated pneumonia have a significant effect on participants' knowledge and subsequent clinical practice.

Effect of colectomy on gastric emptying in idiopathic slow-transit constipation.

PubMed

Hemingway, D M; Finlay, I G

2000-09-01

Gastric emptying is delayed in patients with idiopathic slow-transit constipation (ISTC). Gastric emptying was measured before and after colectomy and ileorectal anastomosis in patients with ISTC to determine whether the abnormality persists after operation. Twelve patients undergoing colectomy for severe ISTC had solid-phase gastric emptying measured after an overnight fast. All 12 had an uncomplicated subtotal colectomy and ileorectal anastomosis; 11 had an excellent functional outcome. In ten of these patients gastric emptying was repeated within 3 months of operation. Seven patients (including the remaining two) had the study performed at 1 year. All 12 patients had severely delayed gastric emptying before operation. Gastric emptying remained delayed in the ten patients who underwent an early postoperative gastric emptying study. Six of seven patients assessed at 1 year had improved gastric emptying, of whom four had returned to normal. Functional outcome did not relate to gastric emptying. Patients with ISTC have delayed gastric emptying. In some patients this returns to normal after colectomy, but is persistent in others. This may have implications for our understanding of ISTC.

Scabies

MedlinePlus

... the skin of other people. The itching of scabies results from your body's allergic reaction to the mites, their eggs and their waste. Close physical contact and, less often, sharing clothing or bedding with an infected person can spread the mites. Dogs, cats and humans all are affected by their ...

Revised Lithostratigraphy of the Sonsela Member (Chinle Formation, Upper Triassic) in the Southern Part of Petrified Forest National Park, Arizona

PubMed Central

Martz, Jeffrey W.; Parker, William G.

2010-01-01

Background Recent revisions to the Sonsela Member of the Chinle Formation in Petrified Forest National Park have presented a three-part lithostratigraphic model based on unconventional correlations of sandstone beds. As a vertebrate faunal transition is recorded within this stratigraphic interval, these correlations, and the purported existence of a depositional hiatus (the Tr-4 unconformity) at about the same level, must be carefully re-examined. Methodology/Principal Findings Our investigations demonstrate the neglected necessity of walking out contacts and mapping when constructing lithostratigraphic models, and providing UTM coordinates and labeled photographs for all measured sections. We correct correlation errors within the Sonsela Member, demonstrate that there are multiple Flattops One sandstones, all of which are higher than the traditional Sonsela sandstone bed, that the Sonsela sandstone bed and Rainbow Forest Bed are equivalent, that the Rainbow Forest Bed is higher than the sandstones at the base of Blue Mesa and Agate Mesa, that strata formerly assigned to the Jim Camp Wash beds occur at two stratigraphic levels, and that there are multiple persistent silcrete horizons within the Sonsela Member. Conclusions/Significance We present a revised five-part model for the Sonsela Member. The units from lowest to highest are: the Camp Butte beds, Lot's Wife beds, Jasper Forest bed (the Sonsela sandstone)/Rainbow Forest Bed, Jim Camp Wash beds, and Martha's Butte beds (including the Flattops One sandstones). Although there are numerous degradational/aggradational cycles within the Chinle Formation, a single unconformable horizon within or at the base of the Sonsela Member that can be traced across the entire western United States (the “Tr-4 unconformity”) probably does not exist. The shift from relatively humid and poorly-drained to arid and well-drained climatic conditions began during deposition of the Sonsela Member (low in the Jim Camp Wash beds), well after the Carnian-Norian transition. PMID:20174475

Measurement of gastric emptying during and between meal intake in free-feeding Lewis rats.

PubMed

van der Velde, P; Koslowsky, I; Koopmans, H S

1999-02-01

A new scintigraphic measurement technique is described that allows accurate assessment of gastric emptying in between as well as during a number of successive meals. Measurements were made every minute of food intake, gastric nutrient filling, and gastric emptying over a 6 h, 40 min period in conscious, free-feeding, loosely restrained rats. Before receiving access to the food, the animals had been deprived for a period of 31 h. Over the full duration of the experiment, an average rate of gastric emptying of 2.46 +/- 0.18 (SE) kcal/h was established. During most meals, however, the gastric emptying rate was increased so that an average of 26.9 +/- 2.7% of the ingested calories was emptied while the animals were feeding, with an average emptying rate of 0.15 +/- 0.014 kcal/min or 8.88 +/- 0.84 kcal/h. This transient increase in the rate of gastric emptying was followed by a subsequent slowing of gastric emptying after meal termination; in the 10-min postmeal interval, an average emptying rate of 0.96 +/- 0.12 kcal/h was found. Despite these fluctuations during and immediately after meals, a relatively constant rate of caloric emptying is maintained over longer periods. There were no differences between the emptying rate during the first meal when the gastrointestinal tract was still empty, compared with later meals when the gastrointestinal tract had been filled with food. The emptying rate during the 10-min postmeal interval, however, was significantly reduced during later meals. The results suggest that gastric emptying is controlled by different mechanisms during and after the ingestion of food and that these mechanisms remain in effect at various degrees of gastrointestinal filling.

A Multistage Fluidized Bed for the Deep Removal of Sour Gases: Proof of Concept and Tray Efficiencies

PubMed Central

2018-01-01

Currently there are significant amounts of natural gas that cannot be produced and treated to meet pipeline specifications, because that would not be economically viable. This work investigates a bench scale multistage fluidized bed (MSFB) with shallow beds for sour gas removal from natural gas using a commercially available supported amine sorbent. A MSFB is regarded as a promising adsorber type for deep sour gas removal to parts per million concentrations. A series of experiments was conducted using carbon dioxide as sour gas and nitrogen to mimic natural gas. Removal below 3 mol ppm was successfully demonstrated. This indicates that gas bypassing is minor (that is, good gas–solid contacting) and that apparent adsorption kinetics are fast for the amine sorbent applied. Tray efficiencies for a chemisorption/adsorption system were reported for one of the first times. Current experiments performed at atmospheric pressure strongly indicate that deep removal is possible at higher pressures in a multistage fluidized bed. PMID:29606794

A Multistage Fluidized Bed for the Deep Removal of Sour Gases: Proof of Concept and Tray Efficiencies.

PubMed

Driessen, Rick T; Bos, Martin J; Brilman, Derk W F

2018-03-21

Currently there are significant amounts of natural gas that cannot be produced and treated to meet pipeline specifications, because that would not be economically viable. This work investigates a bench scale multistage fluidized bed (MSFB) with shallow beds for sour gas removal from natural gas using a commercially available supported amine sorbent. A MSFB is regarded as a promising adsorber type for deep sour gas removal to parts per million concentrations. A series of experiments was conducted using carbon dioxide as sour gas and nitrogen to mimic natural gas. Removal below 3 mol ppm was successfully demonstrated. This indicates that gas bypassing is minor (that is, good gas-solid contacting) and that apparent adsorption kinetics are fast for the amine sorbent applied. Tray efficiencies for a chemisorption/adsorption system were reported for one of the first times. Current experiments performed at atmospheric pressure strongly indicate that deep removal is possible at higher pressures in a multistage fluidized bed.

Fibrin gel improves tissue ingrowth and cell differentiation in human immature premolars implanted in rats.

PubMed

Ruangsawasdi, Nisarat; Zehnder, Matthias; Weber, Franz E

2014-02-01

In pulpless immature human premolars implanted in rodents, this study investigated whether fibrin gel offered advantages over leaving the root canal empty regarding soft tissue ingrowth and cell differentiation. Root canals of extracted human immature premolars (n = 12) were accessed and then irrigated with 5% sodium hypochlorite followed by 17% ethylenediaminetetraacetic acid. Root canals were then either left empty or filled with a fibrin gel (n = 6 each) before being placed subcutaneously on top of the calvarial bone of rats (1 tooth per rat) for 12 weeks. After sacrifice, teeth were histologically assessed. Tissue ingrowth was quantified and compared between groups using the Mann-Whitney U test (P < .05). Cells adhering to the pulp canal wall were immunohistochemically screened for the presence of bone sialoprotein (BSP) and dentin sialoprotein (DSP). More tissue grew into the pulp space when teeth were filled with fibrin gel (P < .05). The presence of fibrin gel affected not only the extent of tissue ingrowth but also tissue morphology and differentiation of cells contacting the dentinal wall. In the fibrin gel group, newly formed tissue was similar to normal pulp, constituted of inner pulp, cell-rich zone, cell-free zone, and an apparent odontoblast layer, which stained positive for BSP and DSP. Newly formed blood vessels were also more abundant compared with the initially empty root canals. Under the conditions of this study, fibrin gel improved cell infiltration and cell-dentin interaction. Both are necessary for pulp tissue regeneration. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Performance of a system with full- and pilot-scale sludge drying reed bed units treating septic tank sludge in Brazil.

PubMed

Calderón-Vallejo, Luisa Fernanda; Andrade, Cynthia Franco; Manjate, Elias Sete; Madera-Parra, Carlos Arturo; von Sperling, Marcos

2015-01-01

This study investigated the performance of sludge drying reed beds (SDRB) at full- and pilot-scale treating sludge from septic tanks in the city of Belo Horizonte, Brazil. The treatment units, planted with Cynodon spp., were based on an adaptation of the first-stage of the French vertical-flow constructed wetland, originally developed for treating sewage. Two different operational phases were investigated; in the first one, the full-scale unit was used together with six pilot-scale columns in order to test different feeding strategies. For the second phase, only the full-scale unit was used, including a recirculation of the filtered effluent (percolate) to one of the units of the French vertical wetland. Sludge application was done once a week emptying a full truck, during 25 weeks. The sludge was predominantly diluted, leading to low solids loading rates (median values of 18 kgTS m(-2) year(-1)). Chemical oxygen demand removal efficiency in the full-scale unit was reasonable (median of 71%), but the total solids removal was only moderate (median of 44%) in the full-scale unit without recirculation. Recirculation did not bring substantial improvements in the overall performance. The other loading conditions implemented in the pilot columns also did not show statistically different performances.

Methane biofiltration in the presence of ethanol vapor under steady and transient state conditions: an experimental study.

PubMed

Ferdowsi, Milad; Ramirez, Antonio Avalos; Jones, Joseph Peter; Heitz, Michèle

2017-09-01

Methane (CH 4 ) removal in the presence of ethanol vapors was performed by a stone-based bed and a hybrid packing biofilter in parallel. In the absence of ethanol, a methane removal efficiency of 55 ± 1% was obtained for both biofilters under similar CH 4 inlet load (IL) of 13 ± 0.5 g CH4  m -3  h -1 and an empty bed residence time (EBRT) of 6 min. The results proved the key role of the bottom section in both biofilters for simultaneous removal of CH 4 and ethanol. Ethanol vapor was completely eliminated in the bottom sections for an ethanol IL variation between 1 and 11 g ethanol  m -3  h -1 . Ethanol absorption and accumulation in the biofilm phase as well as ethanol conversion to CO 2 contributed to ethanol removal efficiency of 100%. In the presence of ethanol vapor, CO 2 productions in the bottom section increased almost fourfold in both biofilters. The ethanol concentration in the leachate of the biofilter exceeding 2200 g ethanol  m -3 leachate in both biofilters demonstrated the excess accumulation of ethanol in the biofilm phase. The biofilters responded quickly to an ethanol shock load followed by a starvation with 20% decrease of their performance. The return to normal operations in both biofilters after the transient conditions took less than 5 days. Unlike the hybrid packing biofilter, excess pressure drop (up to 1.9 cmH 2 O m -1 ) was an important concern for the stone bed biofilter. The biomass accumulation in the bottom section of the stone bed biofilter contributed to 80% of the total pressure drop. However, the 14-day starvation reduced the pressure drop to 0.25 cmH 2 O m -1 .

Empty sella associated with growth hormone deficiency and polydactyly.

PubMed

Jurcă, Maria Claudia; Bembea, Marius; Kozma, Kinga; Şandor, Mircea Ioan; Negrean, Rodica Anamaria; Dobjanschi, Luciana; Cuc, Emilia Albiniţa; Petcheşi, Codruţa Diana; Jurcă, Alexandru Daniel

2018-01-01

Empty sella means the absence of the pituitary gland on cranial computed tomography or magnetic resonance imaging. Empty sella syndrome is the pathological variant of the imaging-described empty sella. We present the case of a male Caucasian child, aged four years and two months, for short stature and diagnosed by imaging procedures as empty sella. The cause of short stature was isolated growth hormone (GH) deficiency. Associated he presented left hand postaxial polydactyly. In connection with this particular case, we propose a review of current knowledge in empty sella syndrome. The particularity of reported case consists of association empty sella with GH deficiency and polydactyly. The association of empty sella with polydactyly is not reported yet in the medical literature and is probably coincidental.

Stomach emptiness in fishes: Sources of variation and study design implications

USGS Publications Warehouse

Vinson, M.R.; Angradi, T.R.

2011-01-01

This study summarizes fish stomach content data from 369,000 fish from 402 species in 1,096 collections and reports on the percentage of individuals with empty stomachs. The mean percentage of individuals with empty stomachs among all species, locations, habitats, seasons, regions, and collection methods was 26.4%. Mean percentage of individuals with empty stomachs varied significantly among fish collection gear types, taxonomic orders, trophic groups, feeding behaviors, and habitats, and with species length at maturity. Most of the variation in percentage of individuals with empty stomachs was explained by species length at maturity, fish collection gear type, and two autecological factors: trophic group (piscivore percentage of individuals with empty stomachs > non-piscivore percentage of individuals with empty stomachs) and feeding habitat (water column feeder percentage of individuals with empty stomachs > benthic feeder percentage of individuals with empty stomachs). After accounting for variation with fish length, the percentage of individuals with empty stomachs did not vary with the stomach removal collection method (dissection vs. gastric lavage), feeding time (diurnal or nocturnal), or time of collection (day or night). The percentage of individuals with empty stomachs was similar between fresh and saltwater fish, but differed within finer habitat classifications and appeared to follow a general prey availability or productivity gradient: percentage of individuals with empty stomachs of open ocean collections > estuary collections, lentic > lotic, and pelagic > littoral. Gear type (active or passive) was the most influential factor affecting the occurrence of empty stomachs that can be readily controlled by researchers.

Process for upgrading arsenic-containing oils

DOEpatents

Sullivan, Richard F.

1979-01-01

A method is provided for avoiding feed-transfer-line plugging by a deposit comprising arsenic in hydroprocessing an oil containing an arsenic contaminant. In the method, a mixture of hydrogen gas and the oil is formed in situ in a bed of porous particulate contact material.

Ammonia Offgassing from SA9T

NASA Technical Reports Server (NTRS)

Monje, Oscar; Nolek, Sara D.; Wheeler, Raymond M.

2011-01-01

NH3 is a degradation product of SA9T, a solid-amine sorbent developed by Hamilton Sundstrand, that is continually emitted into the gas stream being conditioned by this sorbent. NH3 offgassing rates were measured using FTIR spectroscopy using a packed bed at similar contact times as offgassing tests conducted at Hamilton Sundstrand and at the Ames Research Center. The bed was challenged with moist air at several flow rates and humidities and NH3 concentration of the effluent was measured for several hours. The NH3 offgassing rates in open-loop testing were calculated from the steady state outlet NH3 concentration and flow rate. NH3 offgassing rates from SA9T were found to be influenced by the contact time with the adsorbent (flow rate) and by the humidity of the inlet gas stream, which are consistent with previous studies. Closed-loop vacuum-swing adsorption cycling rates verified that NH3 offgassing continues when a constant source of water vapor is present.

Development of a novel proton exchange membrane-free integrated MFC system with electric membrane bioreactor and air contact oxidation bed for efficient and energy-saving wastewater treatment.

PubMed

Gao, Changfei; Liu, Lifen; Yang, Fenglin

2017-08-01

A novel combined system integrating MFC and electric membrane bioreactor (EMBR) was developed, in which a quartz sand chamber (QSC) was used, replacing expensive proton exchange membrane (PEM). An air contact oxidation bed (ACOB) and embedded trickling filter (TF) with filled volcano rock, was designed to increase dissolved oxygen (DO) in cathodic EMBR to save aeration cost. Membrane fouling in EMBR was successful inhibited/reduced by the generated bioelectricity of the system. The combined system demonstrated superior effluent quality in removing chemical oxygen demand (>97%) and ammonia nitrogen (>93%) during the stable operation, and the phosphorus removal was about 50%. Dominant bacteria (Nitrosomonas sp.; Comamonas sp.; Candidatus Kuenenia) played important roles in the removal of organic matter and ammonia nitrogen. The system has good application prospects in the efficient use of water and the development of sustainable wastewater recycling technology. Copyright © 2017. Published by Elsevier Ltd.

Impact of projectiles of different geometries on dry granular media using DEM simulations

NASA Astrophysics Data System (ADS)

Vajrala, Spandana; Bagheri, Hosain; Emady, Heather; Marvi, Hamid; Particulate Process; Product Design Group Team; Birth Lab Collaboration

Recently, several studies involving numerical and experimental methods have focused on the study of impact dynamics in both dry and wet granular media. Most of these studies considered the impact of spherical projectiles under different conditions, while representative models could involve more complex shapes. Examples include such things as an animal's foot impacting sand or an asteroid hitting the ground. Dropping different shaped geometries with conserved density, volume and velocity on a granular bed may experience contrasting drag forces upon penetration. This is the result of the difference in the surface areas coming in contact with the granular media. Therefore, this work will utilize three-dimensional Discrete Element Modelling (DEM) simulations to observe and compare the impact of different geometries like cylinder and cuboid of same material properties and volume. These geometries will be impacted on a loosely packed non-cohesive dry granular bed with the same impact velocities where the effect of surface area in contact with the granular media will be analyzed upon impact and penetration.

Mechanism test bed. Flexible body model report

NASA Technical Reports Server (NTRS)

Compton, Jimmy

1991-01-01

The Space Station Mechanism Test Bed is a six degree-of-freedom motion simulation facility used to evaluate docking and berthing hardware mechanisms. A generalized rigid body math model was developed which allowed the computation of vehicle relative motion in six DOF due to forces and moments from mechanism contact, attitude control systems, and gravity. No vehicle size limitations were imposed in the model. The equations of motion were based on Hill's equations for translational motion with respect to a nominal circular earth orbit and Newton-Euler equations for rotational motion. This rigid body model and supporting software were being refined.

Biocidal quaternary ammonium resin

NASA Technical Reports Server (NTRS)

Janauer, G. E.

1983-01-01

Activated carbon (charcoal) and polymeric resin sorbents are widely used in the filtration and treatment of drinking water, mainly to remove dissolved organic and inorganic impurities and to improve the taste. Earlier hopes that activated carbon might "disinfect' water proved to be unfounded. The feasibility of protecting against microbial infestation in charcoal and resin beds such as those to be incorporated into total water reuse systems in spacecraft was investigated. The biocidal effect of IPCD (insoluable polymeric contact disinfectants) in combination with a representative charcoal was assessed. The ion exchange resins (IPCD) were shown to adequately protect charcoal and ion exchange beds.

Packed bed carburization of tantalum and tantalum alloy

DOEpatents

Lopez, Peter C.; Rodriguez, Patrick J.; Pereyra, Ramiro A.

1999-01-01

Packed bed carburization of a tantalum or tantalum alloy object. A method for producing corrosion-resistant tantalum or tantalum alloy objects is described. The method includes the steps of placing the object in contact with a carburizing pack, heating the packed object in vacuum furnace to a temperature whereby carbon from the pack diffuses into the object forming grains with tantalum carbide along the grain boundaries, and etching the surface of the carburized object. This latter step removes tantalum carbides from the surface of the carburized tantalum object while leaving the tantalum carbide along the grain boundaries.

Packed bed carburization of tantalum and tantalum alloy

DOEpatents

Lopez, P.C.; Rodriguez, P.J.; Pereyra, R.A.

1999-06-29

Packed bed carburization of a tantalum or tantalum alloy object is disclosed. A method for producing corrosion-resistant tantalum or tantalum alloy objects is described. The method includes the steps of placing the object in contact with a carburizing pack, heating the packed object in vacuum furnace to a temperature whereby carbon from the pack diffuses into the object forming grains with tantalum carbide along the grain boundaries, and etching the surface of the carburized object. This latter step removes tantalum carbides from the surface of the carburized tantalum object while leaving the tantalum carbide along the grain boundaries. 4 figs.

Aligning quality and payment for heart failure care: defining the challenges.

PubMed

Havranek, Edward P; Krumholz, Harlan M; Dudley, R Adams; Adams, Kirkwood; Gregory, Douglas; Lampert, Steven; Lindenfeld, Joann; Massie, Barry M; Pina, Ileana; Restaino, Susan; Rich, Michael W; Konstam, Marvin A

2003-08-01

Hospitals may not support programs that improve the quality of care delivered to heart failure patients because these programs lower readmission rates and empty beds, and therefore further diminish already-declining revenues. A conflict between the highest quality of care and financial solvency does not serve the interests of patients, physicians, hospitals, or payers. In principle, resolution of this conflict is simple: reimbursement systems should reward higher quality care. In practice, resolving the conflict is not simple. A recent roundtable discussion sponsored by the Heart Failure Society of America identified 4 major challenges to the design and implementation of reimbursement schemes that promote higher quality care for heart failure: defining quality, accounting for differences in disease severity, crafting novel payment mechanisms, and overcoming professional parochialism. This article describes each of these challenges in turn.

A biofilter for treating toluene vapors: performance evaluation and microbial counts behavior

PubMed Central

Zhu, Yazhong; Luo, Yimeng; Ma, Hongye; Wang, Yan

2016-01-01

A lab-scale biofilter packed with mixed packing materials was used for degradation of toluene. Different empty bed residence times, 148.3, 74.2 and 49.4 s, were tested for inlet concentration ranging from 0.2 to 1.2 g/m3. The maximum elimination capacity of 36.0 g/(m3 h) occurred at an inlet loading rate of 45.9 g/(m3 h). The contribution of the lower layer was higher than other layers and always had the highest elimination capacity. The carbon dioxide production rate and distribution of micro-organisms followed toluene elimination capacities. The results of this study indicated that mixed packing materials could be considered as a potential biofilter carrier, with low pressure drop (less than 84.9 Pa/m), for treating air streams containing VOCs. PMID:27231662

Special report. Twin Cities hospital breaks down ambulatory care, overcomes fears of outpatient care.

PubMed

1995-01-06

With payers pushing for shorter hospital stays and outpatient services generating growing shares of hospitals' revenues, experts everywhere are projecting the end of the traditional inpatient-oriented hospital. Those predictions have triggered a scramble by many hospital managers to adapt their organizations and empty beds to the expected predominance of same-day services. One Minnesota facility that surveyed the outpatient trend, however, found that its strategic options weren't limited to becoming a jumbo-sized outpatient clinic, explain David Allen, a partner with The Chancellor Group, Bloomington, Minn., and Daniel Weber, vice president of Fairview Southdale Hospital, Edina, Minn., in this special report. By understanding the multidimensional nature of ambulatory services and focusing its efforts on becoming a regional hub of healthcare services, Fairview Southdale has carved its own niche in a changing provider market.

Removal of traces of toluene and p-xylene in indoor air using biofiltration and a hybrid system (biofiltration + adsorption).

PubMed

Luengas, Angela Tatiana; Hort, Cécile; Platel, Vincent; Elias, Ana; Barona, Astrid; Moynault, Laurent

2017-04-01

Biofiltration technology and the hybrid system combining biofiltration and adsorption (onto activated carbon) were compared as possible methods to toluene and p-xylene at parts per million concentration levels (2-45 and 1-33 ppb, respectively). An organic material was used as packing material for the biofiltration process. Even at low empty bed residence times (EBRTs) and concentrations, toluene removal efficiency reached 100% and p-xylene showed an increasing trend on their removal efficiency over the time using biofiltration. The assessment of by-products and particle generation by the biofilter and the hybrid system were taken into account. Acetone and acetic acid were identified as by-products of the biofilter. Particle emissions in the range of 0.03 to 10 μm were recorded for both systems.

The fluidized bed separator

NASA Astrophysics Data System (ADS)

Sharapov, R. R.; Kharlamov, E. V.; Yadykina, V. V.

2018-03-01

In the production of building materials produces a large amount of harmful substances, poisoning atmosphere and adjacent to the building materials site. One of the biggest polluting the ecology of cities adjacent to industry, is metallurgical industry. One of the most important technological processes is the enrichment, in which the rocks are extracted empty components. In the enrichment of iron ore in the production an increasing proportion consist the anthropogenic waste industries, which pollute the air basin and the huge territory around the factories that dumped these same wastes. This reduces as a space for human life and for the functioning and development of cities. These materials can be applied as construction materials, for example, in the preparation of fine-grained concrete as a mineral powder, and these materials can be applied in the construction of roads, housing, for receiving paint etc.

Videodermoscopy does not enhance diagnosis of scalp contact dermatitis due to topical minoxidil.

PubMed

Tosti, Antonella; Donati, Aline; Vincenzi, Colombina; Fabbrocini, Gabriella

2009-07-01

Videodermoscopy (VD) is a noninvasive diagnostic tool that provides useful information for the differential diagnosis of scalp disorders. The aim of this study was to investigate if dermoscopy may help the clinician in the diagnosis of contact dermatitis of the scalp. We analyzed the dermoscopic images taken from 7 patients with contact dermatitis due to topical minoxidil, 6 patients complaining of intense scalp itching during treatment with topical minoxidil but with negative patch tests and 19 controls. The following dermoscopic patterns described for scalp diseases were evaluated: Vascular patterns (simple loops, twisted loops and arborizing lines), follicular/perifollicular patterns (yellow dots, empty ostia, white dots, peripilar signs), white scales, yellow scales, follicular plugging, hair diameter diversity, honeycomb pattern and short regrowing hairs. Findings were graded from 0-4, according to severity in 20-fold magnifications. Statistical analysis included univariate analysis and Chi-square test by SPSS version 12. There were no statistical differences in the analysis of the vascular patterns and scales between the 3 groups. We were not able to detect dermoscopic features that can help the clinician in distinguishing scalp contact dermatitis due to topical minoxidil from other conditions that cause severe scalp itching. In particular, minoxidil contact dermatitis does not produce increase or alterations in the morphology of the scalp vessels or significant scalp scaling when evaluated with dermoscopy.

Preference for social contact versus environmental enrichment in male laboratory mice.

PubMed

Van Loo, P L P; Van de Weerd, H A; Van Zutphen, L F M; Baumans, V

2004-04-01

Due to their aggressive nature, male mice are less frequently used than female mice in biomedical research. When aggressive males are being used, individual housing is common practice. The question arises whether this is an acceptable housing for a social species. The present study was designed to gain more insight into the nature of inter-male social contact and into the potential of a form of environmental enrichment (nesting material) to compensate for the lack of social contact. In a series of tests, we analysed whether male mice of different ages preferred to spend time (1) near a familiar cage mate versus an empty cage, or (2) near to a familiar cage mate versus direct contact with nesting material (tissues). Dwelling time in each of the test cages and sleeping sites was recorded, as was the behaviour of the test mice. Results indicated that when other conditions were similar, male mice preferred to sleep in close proximity to their familiar cage mate. Furthermore, the need to engage in active social behaviour increased with age. Tissues were used to a large extent for sleeping and sleep-related behaviour. It is concluded that single housing in order to avoid aggression between male mice is a solution with evident negative consequences for the animals. When individual housing is inevitable due to excessive aggressive behaviour, the presence of nesting material could partly compensate for the deprivation of social contact.

Bacillus cereus in free-stall bedding.

PubMed

Magnusson, M; Svensson, B; Kolstrup, C; Christiansson, A

2007-12-01

To increase the understanding of how different factors affect the bacterial growth in deep sawdust beds for dairy cattle, the microbiological status of Bacillus cereus and coliforms in deep sawdust-bedded free stalls was investigated over two 14-d periods on one farm. High counts of B. cereus and coliforms were found in the entire beds. On average, 4.1 log(10) B. cereus spores, 5.5 log(10) B. cereus, and 6.7 log(10) coliforms per gram of bedding could be found in the upper layers of the sawdust likely to be in contact with the cows' udders. The highest counts of B. cereus spores, B. cereus, and coliforms were found in the bedding before fresh bedding was added, and the lowest immediately afterwards. Different factors of importance for the growth of B. cereus in the bedding material were explored in laboratory tests. These were found to be the type of bedding, pH, and the type and availability of nutrients. Alternative bedding material such as peat and mixtures of peat and sawdust inhibited the bacterial growth of B. cereus. The extent of growth of B. cereus in the sawdust was increased in a dose-dependent manner by the availability of feces. Urine added to different bedding material raised the pH and also led to bacterial growth of B. cereus in the peat. In sawdust, a dry matter content greater than 70% was needed to lower the water activity to 0.95, which is needed to inhibit the growth of B. cereus. In an attempt to reduce the bacterial growth of B. cereus and coliforms in deep sawdust beds on the farm, the effect of giving bedding daily or a full replacement of the beds was studied. The spore count of B. cereus in the back part of the free stalls before fresh bedding was added was 0.9 log units lower in stalls given daily bedding than in stalls given bedding twice weekly. No effect on coliform counts was found. Replacement of the entire sawdust bedding had an effect for a short period, but by 1 to 2 mo after replacement, the counts of B. cereus spores in the beds had increased about 2 log units and were as high as they were before bed replacement. Therefore, free-stall management could, to a limited extent, reduce the content of B. cereus spores in the beds by daily bedding and entire bed replacement.

What is emptiness? Clarifying the 7th criterion for borderline personality disorder.

PubMed

Klonsky, E David

2008-08-01

The present study aims to clarify the 7th DSM-IV criterion for Borderline Personality Disorder: "chronic feelings of emptiness." Emptiness has been the subject of little empirical investigation. The relationship of emptiness to boredom and other affect-states is uncertain, and patients and clinicians can find it difficult to generate verbal descriptions of emptiness. In the present study, two sets of analyses address the meaning and clinical implications of feeling empty. First, affect-states that co-occur with emptiness are identified in 45 young adults who exhibit a prominent feature of Borderline Personality Disorder (i.e., self-injury). Second, the relationship of chronic emptiness to key psychiatric variables is examined in a large nonclinical sample (n = 274). Results indicate that emptiness is negligibly related to boredom, is closely related to feeling hopeless, lonely, and isolated, and is a robust predictor of depression and suicidal ideation (but not anxiety or suicide attempts). Findings are consistent with DSM-IV revisions regarding the 7th criterion for Borderline Personality Disorder. In addition, findings suggest that emptiness reflects pathologically low positive affect and significant psychiatric distress.

Conditions for a steady ice sheet ice shelf junction

NASA Astrophysics Data System (ADS)

Nowicki, S. M. J.; Wingham, D. J.

2008-01-01

This paper investigates the conditions under which a marine ice sheet may adopt a steady profile. The ice is treated as a linear viscous fluid caused to flow from a rigid base to and over water, treated as a denser but inviscid fluid. The solutions in the region around the point of flotation, or 'transition' zone, are calculated numerically. In-flow and out-flow conditions appropriate to ice sheet and ice shelf flow are applied at the ends of the transition zone and the rigid base is specified; the flow and steady free surfaces are determined as part of the solutions. The basal stress upstream, and the basal deflection downstream, of the flotation point are examined to determine which of these steady solutions satisfy 'contact' conditions that would prevent (i) the steady downstream basal deflection contacting the downstream base, and (ii) the upstream ice commencing to float in the event it was melted at the base. In the case that the upstream bed is allowed to slide, we find only one mass flux that satisfies the contact conditions. When no sliding is allowed at the bed, however, we find a range of mass fluxes satisfy the contact conditions. The effect of 'backpressure' on the solutions is investigated, and is found to have no affect on the qualitative behaviour of the junctions. To the extent that the numerical, linearly viscous treatment may be applied to the case of ice flowing out over the ocean, we conclude that when sliding is present, Weertman's 'instability' hypothesis holds.

Whole-arm tactile sensing for beneficial and acceptable contact during robotic assistance.

PubMed

Grice, Phillip M; Killpack, Marc D; Jain, Advait; Vaish, Sarvagya; Hawke, Jeffrey; Kemp, Charles C

2013-06-01

Many assistive tasks involve manipulation near the care-receiver's body, including self-care tasks such as dressing, feeding, and personal hygiene. A robot can provide assistance with these tasks by moving its end effector to poses near the care-receiver's body. However, perceiving and maneuvering around the care-receiver's body can be challenging due to a variety of issues, including convoluted geometry, compliant materials, body motion, hidden surfaces, and the object upon which the body is resting (e.g., a wheelchair or bed). Using geometric simulations, we first show that an assistive robot can achieve a much larger percentage of end-effector poses near the care-receiver's body if its arm is allowed to make contact. Second, we present a novel system with a custom controller and whole-arm tactile sensor array that enables a Willow Garage PR2 to regulate contact forces across its entire arm while moving its end effector to a commanded pose. We then describe tests with two people with motor impairments, one of whom used the system to grasp and pull a blanket over himself and to grab a cloth and wipe his face, all while in bed at his home. Finally, we describe a study with eight able-bodied users in which they used the system to place objects near their bodies. On average, users perceived the system to be safe and comfortable, even though substantial contact occurred between the robot's arm and the user's body.

Nothing to it: Precursors to a Zero Concept in Preschoolers

PubMed Central

Merritt, Dustin J.; Brannon, Elizabeth M.

2013-01-01

Do young children understand the numerical value of empty sets prior to developing a concept of symbolic zero? Are empty sets represented as mental magnitudes? In order to investigate these questions, we tested 4-year old children and adults with a numerical ordering task in which the goal was to select two stimuli in ascending numerical order with occasional empty set stimuli. Both children and adults showed distance effects for empty sets.. Children who were unable to order the symbol zero (e.g., 0 < 1), but who successfully ordered countable integers (e.g., 2 < 4) nevertheless showed distance effects with empty sets. These results suggest that empty sets are represented on the same numerical continuum as non-empty sets and that children represent empty sets numerically prior to understanding symbolic zero. PMID:23219980

Process for the preparation of cumene

DOEpatents

Smith, Jr., Lawrence A.; Arganbright, Robert P.; Hearn, Dennis

1991-01-01

Cumene is produced in a catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 50.degree. C. to 500.degree. C., using as the catalyst a mole sieve characterized as acidic by feeding propylene to the catalyst bed while benzene is conveniently added through the reflux to result in a molar excess present in the reactor to that required to react with propylene, thereby reacting substantially all of the propylene and recovering benzene as the principal overhead and cumene and diisopropyl benzene in the bottoms. The bottoms are fractionated, the cumene recovered and the bottoms are contacted with benzene in the liquid phase in a fixed bed straight pass reactor under conditions to transalkylate the benzene thereby converting most of the diisopropyl benzene to cumene which is again separated and recovered.

New data on Berriasian biostratigraphy, magnetostratigraphy, and sedimentology in the Belogorsk area (Central Crimea)

NASA Astrophysics Data System (ADS)

Arkadiev, V. V.; Baraboshkin, E. Yu.; Bagaeva, M. I.; Bogdanova, T. N.; Guzhikov, A. Yu.; Manikin, A. G.; Piskunov, V. K.; Platonov, E. S.; Savel'eva, Yu. N.; Feodorova, A. A.; Shurekova, O. V.

2015-03-01

The most complete composite Berriasian bio- and magnetostratigraphic section of central Crimea is characterized for the first time with a description of the contact between the carbonate Bedenekyr and terrigenous Bechku formations. The section contains all the standard ammonite zones: jacobi, occitanica, and boissieri. The Malbosiceras chaperi Beds are attributed to the occitanica Zone. The Berriasian section is characterized by six foraminiferal assemblages, ostracods (Costacythere khiamii-Hechticythere belbekensis and Costaythere drushchitzi-Reticythere marfenini beds), and dinocysts (Phobercysta neocomica Beds). The magnetostratigraphic section contains analogs of Chrons M17 and M16 reliably correlated with ammonite zones. On the basis of paleomagnetic data, the Berriasian section of central Crimea is correlated with coeval sections of the Mediterranean Region. The sedimenological analysis confirms accumulation of Berriasian sediments mostly in shallow shelf environments of the carbonate platform.

Process for the preparation of cumene

DOEpatents

Smith, L.A. Jr.; Arganbright, R.P.; Hearn, D.

1991-10-08

Cumene is produced in a catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 50 C to 500 C, using as the catalyst a molecular sieve characterized as acidic by feeding propylene to the catalyst bed while benzene is conveniently added through the reflux to result in a molar excess present in the reactor to that required to react with propylene, thereby reacting substantially all of the propylene and recovering benzene as the principal overhead and cumene and diisopropyl benzene in the bottoms. The bottoms are fractionated, the cumene recovered and the bottoms are contacted with benzene in the liquid phase in a fixed bed straight pass reactor under conditions to transalkylate the benzene thereby converting most of the diisopropyl benzene to cumene which is again separated and recovered. 2 figures.

Process for the preparation of ethyl benzene

DOEpatents

Smith, L.A. Jr.; Arganbright, R.P.; Hearn, D.

1995-12-19

Ethyl benzene is produced in a catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 50 C to 300 C, using as the catalyst a mole sieve characterized as acidic by feeding ethylene to the catalyst bed while benzene is conveniently added through the reflux to result in a molar excess present in the reactor to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene and diethyl benzene in the bottoms. The bottoms are fractionated, the ethyl benzene recovered and the bottoms are contacted with benzene in the liquid phase in a fixed bed straight pass reactor under conditions to transalkylate the benzene thereby converting most of the diethyl benzene to ethyl benzene which is again separated and recovered. 2 figs.

Process for the preparation of ethyl benzene

DOEpatents

Smith, Jr., Lawrence A.; Arganbright, Robert P.; Hearn, Dennis

1995-01-01

Ethyl benzene is produced in a catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 50.degree. C. to 300.degree. C., using as the catalyst a mole sieve characterized as acidic by feeding ethylene to the catalyst bed while benzene is conveniently added through the reflux to result in a molar excess present in the reactor to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene and diethyl benzene in the bottoms. The bottoms are fractionated, the ethyl benzene recovered and the bottoms are contacted with benzene in the liquid phase in a fixed bed straight pass reactor under conditions to transalkylate the benzene thereby converting most of the diethyl benzene to ethyl benzene which is again separated and recovered.

Gastric emptying abnormal in duodenal ulcer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holt, S.; Heading, R.C.; Taylor, T.V.

1986-07-01

To investigate the possibility that an abnormality of gastric emptying exists in duodenal ulcer and to determine if such an abnormality persists after ulcer healing, scintigraphic gastric emptying measurements were undertaken in 16 duodenal ulcer patients before, during, and after therapy with cimetidine; in 12 patients with pernicious anemia, and in 12 control subjects. No difference was detected in the rate or pattern of gastric emptying in duodenal ulcer patients before and after ulcer healing with cimetidine compared with controls, but emptying of the solid component of the test meal was more rapid during treatment with the drug. Comparison ofmore » emptying patterns obtained in duodenal ulcer subjects during and after cimetidine treatment with those obtained in pernicious anemia patients and controls revealed a similar relationship that was characterized by a tendency for reduction in the normal differentiation between the emptying of solid and liquid from the stomach. The similarity in emptying patterns in these groups of subjects suggests that gastric emptying of solids may be influenced by changes in the volume of gastric secretion. The failure to detect an abnormality of gastric emptying in duodenal ulcer subjects before and after ulcer healing calls into question the widespread belief that abnormally rapid gastric emptying is a feature with pathogenetic significance in duodenal ulcer disease.« less

Physical characteristics of indigestible solids affect emptying from the fasting human stomach.

PubMed Central

Meyer, B; Beglinger, C; Neumayer, M; Stalder, G A

1989-01-01

Gastric emptying of indigestible solids depends on their size. It is not clear whether physical characteristics other than particle size affect emptying of indigestible solids from the fasting human stomach. We studied gastric emptying of three differently shaped particles, (cubes, spheres, rods) of either hard or soft consistency during the fasting state in human volunteers. The shape of indigestible particles did not affect their emptying. The area under the gastric emptying curve (AUC: particles x hour) was for hard cubes 24.7 (2.2), for hard spheres 27.9 (1.6), for hard rods 26.9 (2.7). All soft particles emptied faster than their identically shaped hard counterparts, but there was no difference among the three shapes (AUC for soft cubes: 29.2 (3.0), for soft spheres 32.0 (1.8), for soft rods 34.1 (1.2). If gastric emptying of hard and soft particles was compared independently of their shape, soft particles emptied significantly faster than hard ones: AUC 31.8 (1.2) v 26.5 (1.3) (p less than 0.01). In conclusion, the consistency but not the shape significantly affects gastric emptying. Specific physical characteristics other than size and shape may affect gastric emptying of indigestible particles which may be of importance in the design of drugs. PMID:2599438

Remarkably enhanced thermal transport based on a flexible horizontally-aligned carbon nanotube array film

PubMed Central

Qiu, Lin; Wang, Xiaotian; Su, Guoping; Tang, Dawei; Zheng, Xinghua; Zhu, Jie; Wang, Zhiguo; Norris, Pamela M.; Bradford, Philip D.; Zhu, Yuntian

2016-01-01

It has been more than a decade since the thermal conductivity of vertically aligned carbon nanotube (VACNT) arrays was reported possible to exceed that of the best thermal greases or phase change materials by an order of magnitude. Despite tremendous prospects as a thermal interface material (TIM), results were discouraging for practical applications. The primary reason is the large thermal contact resistance between the CNT tips and the heat sink. Here we report a simultaneous sevenfold increase in in-plane thermal conductivity and a fourfold reduction in the thermal contact resistance at the flexible CNT-SiO2 coated heat sink interface by coupling the CNTs with orderly physical overlapping along the horizontal direction through an engineering approach (shear pressing). The removal of empty space rapidly increases the density of transport channels, and the replacement of the fine CNT tips with their cylindrical surface insures intimate contact at CNT-SiO2 interface. Our results suggest horizontally aligned CNT arrays exhibit remarkably enhanced in-plane thermal conductivity and reduced out-of-plane thermal conductivity and thermal contact resistance. This novel structure makes CNT film promising for applications in chip-level heat dissipation. Besides TIM, it also provides for a solution to anisotropic heat spreader which is significant for eliminating hot spots. PMID:26880221

Gastric emptying of solid radiopaque markers: studies in healthy subjects and diabetic patients.

PubMed

Feldman, M; Smith, H J; Simon, T R

1984-10-01

The purpose of these studies was to develop a radiologic method for assessing gastric emptying of an indigestible solid in humans and to apply this technique to the evaluation of patients with diabetes mellitus. Thirty healthy subjects ingested 10 solid radiopaque markers (small pieces of nasogastric tubing) together with a standard meal (donuts and 7-Up). Radiographs of the upper abdomen were obtained hourly for up to 6 h until all markers had emptied from the stomach. Although most of the liquid component of the meal, labeled with 111In, emptied during the first hour (as assessed simultaneously by radionuclide scintigraphy), few radiopaque markers emptied from the stomach during the first 2 h after the meal. Most markers emptied during the fourth postprandial hour, and all 10 markers had emptied by 6 h in 45 of 46 experiments. In contrast, not all of the solid radiopaque markers emptied from the stomach by 6 h in 16 of 26 experiments in patients with diabetes mellitus (p less than 0.001 vs. healthy controls). In some experiments, 99mTc-labeled scrambled eggs were added to the meal so that emptying of this digestible solid, assessed by scintigraphy, could be compared with emptying of liquids and solid radiopaque markers. In healthy subjects, the digestible solid emptied more slowly than the liquid (t 1/2 = 154 +/- 11 min vs. 30 +/- 3 min, p less than 0.001), but emptying of digestible solid was significantly faster than the emptying of the indigestible solid radiopaque markers. In diabetics, emptying rates for the digestible solid and liquid were close to normal (t 1/2 = 178 +/- 5 min and 40 +/- 3 min, respectively), whereas indigestible solid markers were retained in the stomach 6 h after the meal in 50% of the patients. Radiopaque markers proved to be a simple method for measuring gastric emptying of indigestible solids in humans. Using this technique, patients with insulin-dependent diabetes mellitus had a high incidence of abnormally slow gastric emptying of indigestible solids; the method may be a more sensitive indicator of gastric motor dysfunction than radionuclide scintigraphy.

A review of methods for assessment of the rate of gastric emptying in the dog and cat: 1898-2002.

PubMed

Wyse, C A; McLellan, J; Dickie, A M; Sutton, D G M; Preston, T; Yam, P S

2003-01-01

Gastric emptying is the process by which food is delivered to the small intestine at a rate and in a form that optimizes intestinal absorption of nutrients. The rate of gastric emptying is subject to alteration by physiological, pharmacological, and pathological conditions. Gastric emptying of solids is of greater clinical significance because disordered gastric emptying rarely is detectable in the liquid phase. Imaging techniques have the disadvantage of requiring restraint of the animal and access to expensive equipment. Radiographic methods require administration of test meals that are not similar to food. Scintigraphy is the gold standard method for assessment of gastric emptying but requires administration of a radioisotope. Magnetic resonance imaging has not yet been applied for assessment of gastric emptying in small animals. Ultrasonography is a potentially useful, but subjective, method for assessment of gastric emptying in dogs. Gastric tracer methods require insertion of gastric or intestinal cannulae and are rarely applied outside of the research laboratory. The paracetamol absorption test has been applied for assessment of liquid phase gastric emptying in the dog, but requires IV cannulation. The gastric emptying breath test is a noninvasive method for assessment of gastric emptying that has been applied in dogs and cats. This method can be carried out away from the veterinary hospital, but the effects of physiological and pathological abnormalities on the test are not known. Advances in technology will facilitate the development of reliable methods for assessment of gastric emptying in small animals.

Granular controls on the dispersion of bed load tracers

NASA Astrophysics Data System (ADS)

Jerolmack, D. J.; Martin, R. L.; Phillips, C. B.

2014-12-01

Coarse particles are transported in a river as bed load, i.e., they move in frequent contact with and are supported by the granular bed. This movement is typically intermittent and may be described by a series of steps are rests, the distributions of which determine particle dispersion. Laboratory and field studies of bed load tracer dispersion have reported sub- and super-diffusive behavior, both of which have been successfully reproduced with stochastic transport models. Although researchers have invoked heavy-tailed step lengths as the cause of anomalous dispersion, most observations report thin-tailed distributions. Little attention has been paid to rest periods, and stochastic transport models have not been connected to the underlying mechanics of particle motion. Based on theoretical and experimental evidence, we argue that step lengths are thin-tailed and do not control the longterm dispersion of bed load tracers; they are determined by momentum balance between the fluid and solid. Using laboratory experiments with both marbles and natural sediments, we demonstrate that the rest time distribution is power law, and argue that this distribution controls asymptotic dispersion. Observed rest times far exceed any hydrodynamic timescale. Experiments reveal that rest times of deposited particles are governed by fluctuations in river bed elevation; in particular, the return time for the bed to scour to the base of a deposited particle. Stochastic fluctuations in bed elevation are describable by an Ornstein-Uhlenbeck (mean-reverting random walk) model that contains two parameters, which we show are directly related to the granular shear rate and range of bed elevation fluctuations, respectively. Combining these results with the theory of asymmetric random walks (particles only move downstream), we predict superdiffusive behavior that is in quantitative agreement with our observations of tracer dispersion in a natural river.

Adsorption affinity and selectivity of 3-ureidopropyltriethoxysilane grafted oil palm empty fruit bunches towards mercury ions.

PubMed

Kunjirama, Magendran; Saman, Norasikin; Johari, Khairiraihanna; Song, Shiow-Tien; Kong, Helen; Cheu, Siew-Chin; Lye, Jimmy Wei Ping; Mat, Hanapi

2017-06-01

This study was conducted to investigate the potential application of oil palm empty fruit branches (OPEFB) as adsorbents to remove organic methylmercurry, MeHg(II), and inorganic Hg(II) from aqueous solution. The OPEFB was functionalized with amine containing ligand namely 3-ureidopropyltriethoxysilane (UPTES) aiming for better adsorption performance towards both mercury ions. The adsorption was found to be dependent on initial pH, initial concentraton, temperatures, and contact time. The maximum adsorption capacities (Q m.exp ) of Hg(II) adsorption onto OPEFB and UPTES-OPEFB were 0.226 and 0.773 mmol/g, respectively. The Q m.exp of MeHg(II) onto OPEFB, however, was higher than UPTES-OPEFB. The adsorption kinetic data obeyed the Elovich model and the adsorption was controlled by the film-diffusion step. The calculated thermodynamic parameters indicate an endothermic adsorption process. Adsorption data analysis indicates that the adsorption mechanism may include ion-exchange, complexation, and physisorption interactions. The potential applications of adsorbents were demonstrated using oilfield produced water and natural gas condensate. The UPTES-OPEFB offered higher selectivity towards both mercury ions than OPEFB. The regenerability studies indicated that the adsorbent could be reused for multiple cycles.

Hallucinations, loneliness, and social isolation in Alzheimer's disease.

PubMed

El Haj, Mohamad; Jardri, Renaud; Larøi, Frank; Antoine, Pascal

2016-01-01

Cognitive and functional compromise, as frequently observed in Alzheimer's disease (AD), hinders communication and social interactions. One consequence of this hindrance may be a feeling of loneliness. Moreover, emptiness and boredom, as observed in social isolation and loneliness, may thus be compensated for by creating imagined stimuli. Conditions of loneliness may be viewed as potentially generating hallucinatory experiences. To assess this assumption, the present study explored the relationship between social isolation, loneliness, and hallucinations in a sample of 22 mild AD participants and 24 elderly, healthy controls. Participants were assessed using the Launay-Slade Hallucination Scale, the UCLA Loneliness Scale, and a scale exploring contact with others and social participation. More hallucinatory experiences, social isolation, and loneliness were found in the AD group than in the healthy control group. Moreover, significant correlations were observed between hallucinations and loneliness and between hallucinations and social isolation in both groups. Finally, hallucinations were predicted by social isolation. Hallucinations may constitute a compensatory mechanism that aims to fulfil communication needs in lonely, elderly participants. Hallucinations may also be regarded as experiences that allow certain participants to escape the cycle of boredom, emptiness, and affective deprivation caused by social isolation.

Regional hydrology of the Green River-Moab area, northwestern Paradox Basin, Utah

USGS Publications Warehouse

Rush, F.E.; Whitfield, M.S.; Hart, I.M.

1984-01-01

The Green River-Moab area encompasses about 7,800 square kilometers or about 25 percent of the Paradox basin. The entire Paradox basin is a part of the Colorado Plateaus that is underlain by a thick sequence of evaporite (salt) beds of Pennsylvanian age. The rock units that underlie the area have been grouped into hydrogeologic units based on their water-transmitting ability. Confining beds consist of evaporite beds of mostly salt, and over- lying and underlying thick sequences of rocks with minimal permeability; above and below these confining beds are aquifers. The upper Mesozoic sand- stone aquifer, probably is the most permeable hydrogeologic unit of the area and is the subject of this investigation. The principal component of ground- water outflow from this aquifer probably is subsurface flow to regional streams (the Green and Colorado Rivers) and is about 100 million cubic meters per year. All other components of outflow are relatively small. The average annual recharge to the aquifer is about 130 million cubic meters, of which about 20 million cubic meters is from local precipitation. For the lower aquifer, all recharge and discharge probably is by subsurface flow and was not estimated.The aquifers are generally isolated from the evaporite beds by the bounding confining beds; as a result, most ground water has little if any contact with the evaporites. Brines are present in the confining beds, but solution of beds o£ salt probably is very slow in most parts of the area. No brine discharges' have been identified.

Field evidence for control of quarrying by rock bridges in jointed bedrock

NASA Astrophysics Data System (ADS)

Hooyer, T. S.; Cohen, D. O.; Iverson, N. R.

2011-12-01

Quarrying is generally thought to be the most important mechanism by which glaciers erode bedrock. In quarrying models it is assumed that slow, subcritical, growth of pre-existing cracks rate-limits the process and occurs where there are large stress differences in the bed, such as near rock bumps where ice separates from the bed to form water-filled cavities. Owing to the direction of principal stresses in rocks associated with sliding and resultant cavity formation, models predict that quarrying will occur along cracks oriented perpendicular to the ice flow direction or parallel to zones of ice-bed contact. Preglacial cracks in rocks will tend to propagate mainly downward, and in sedimentary or some metamorphic rocks will merge with bedding planes, thereby helping to isolate rock blocks for dislodgement. In contrast to these model assumptions, new measurements of quarried surface orientations in the deglaciated forefield of nine glaciers in Switzerland and Canada indicate a strong correlation between orientations of pre-existing joints and quarried bedrock surfaces, independent of ice flow direction or ice-water contact lines. The strong correlation persists across all rock types, and rocks devoid of major joints lack quarried surfaces. We propose a new conceptual model of quarrying that idealizes the bedrock as a series of blocks separated by discontinuous preglacial joints containing intact rock bridges. Bridges concentrate stress differences caused by normal and shear forces acting at the rock surface. Failure of bridges is caused by slow subcritical crack growth enhanced by water pressure fluctuations. To lend credibility to this new model, we show field evidence of failed rock bridges in quarried surfaces and of rib marks on plumose structures that we interpret as arrest fracture fronts due to transient subglacial water-pressure fluctuations.

Improving Emergency Department flow through optimized bed utilization

PubMed Central

Chartier, Lucas Brien; Simoes, Licinia; Kuipers, Meredith; McGovern, Barb

2016-01-01

Over the last decade, patient volumes in the emergency department (ED) have grown disproportionately compared to the increase in staffing and resources at the Toronto Western Hospital, an academic tertiary care centre in Toronto, Canada. The resultant congestion has spilled over to the ED waiting room, where medically undifferentiated and potentially unstable patients must wait until a bed becomes available. The aim of this quality improvement project was to decrease the 90th percentile of wait time between triage and bed assignment (time-to-bed) by half, from 120 to 60 minutes, for our highest acuity patients. We engaged key stakeholders to identify barriers and potential strategies to achieve optimal flow of patients into the ED. We first identified multiple flow-interrupting challenges, including operational bottlenecks and cultural issues. We then generated change ideas to address two main underlying causes of ED congestion: unnecessary patient utilization of ED beds and communication breakdown causing bed turnaround delays. We subsequently performed seven tests of change through sequential plan-do-study-act (PDSA) cycles. The most significant gains were made by improving communication strategies: small gains were achieved through the optimization of in-house digital information management systems, while significant improvements were achieved through the implementation of a low-tech direct contact mechanism (a two-way radio or walkie-talkie). In the post-intervention phase, time-to-bed for the 90th percentile of high-acuity patients decreased from 120 minutes to 66 minutes, with special cause variation showing a significant shift in the weekly measurements. PMID:27752312

Improving Emergency Department flow through optimized bed utilization.

PubMed

Chartier, Lucas Brien; Simoes, Licinia; Kuipers, Meredith; McGovern, Barb

2016-01-01

Over the last decade, patient volumes in the emergency department (ED) have grown disproportionately compared to the increase in staffing and resources at the Toronto Western Hospital, an academic tertiary care centre in Toronto, Canada. The resultant congestion has spilled over to the ED waiting room, where medically undifferentiated and potentially unstable patients must wait until a bed becomes available. The aim of this quality improvement project was to decrease the 90th percentile of wait time between triage and bed assignment (time-to-bed) by half, from 120 to 60 minutes, for our highest acuity patients. We engaged key stakeholders to identify barriers and potential strategies to achieve optimal flow of patients into the ED. We first identified multiple flow-interrupting challenges, including operational bottlenecks and cultural issues. We then generated change ideas to address two main underlying causes of ED congestion: unnecessary patient utilization of ED beds and communication breakdown causing bed turnaround delays. We subsequently performed seven tests of change through sequential plan-do-study-act (PDSA) cycles. The most significant gains were made by improving communication strategies: small gains were achieved through the optimization of in-house digital information management systems, while significant improvements were achieved through the implementation of a low-tech direct contact mechanism (a two-way radio or walkie-talkie). In the post-intervention phase, time-to-bed for the 90th percentile of high-acuity patients decreased from 120 minutes to 66 minutes, with special cause variation showing a significant shift in the weekly measurements.

Assessment of Gastric Emptying in Patients with Autoimmune Gastritis.

PubMed

Kalkan, Çağdaş; Soykan, Irfan; Soydal, Çiğdem; Özkan, Elgin; Kalkan, Emra

2016-06-01

Symptoms of patients with autoimmune gastritis are not specific, and some patients may present symptoms suggestive of delayed gastric emptying. This study aims to investigate whether any delay in gastric emptying of solid food exists in patients with autoimmune gastritis and, if so, to identify the factors that might affect delayed gastric emptying. A total of 165 patients (106 women) diagnosed as having autoimmune gastritis were analyzed by means of a gastric emptying test. All patients underwent a standardized scintigraphic gastric emptying study. Patients with delayed gastric emptying and normal gastric emptying tests were then compared by means of factors that might affect gastric emptying. Also 65 patients with functional dyspepsia who had a gastric emptying study constituted the control group. The median gastric emptying T ½ time was 127.43 min (min-max 50-953) for patients with AIG and 81 min (min-max 21-121.6) for functional dyspepsia patients (p < 0.001), and median percent retention at 2 h was 63.8 versus 20.2 (p < 0.001). In multivariate analysis, parameters that affected gastric emptying T ½ time were found as serum gastrin level (OR 1.002, 95 % CI 1.001-1.004, p < 0.001, chronic inflammation (OR 3.689, 95 % CI 1.44-9.39, p < 0.001), and increase in the degree of the atrophy of the gastric mucosa (OR 8.96, 95 % CI 2.98-26.93, p < 0.001). In patients with autoimmune gastritis, gastric emptying is generally delayed. Autoimmune gastritis is an important etiology to explain the finding of delayed gastric emptying on a radionuclide test. This new finding is likely to be relevant to clinicians when evaluating and initiating appropriate medical treatment for patients with autoimmune gastritis manifesting upper gastrointestinal symptoms.

RELATIONSHIP BETWEEN GLYCEMIC CONTROL AND GASTRIC EMPTYING IN POORLY CONTROLLED TYPE 2 DIABETES

PubMed Central

Bharucha, Adil E.; Kudva, Yogish; Basu, Ananda; Camilleri, Michael; Low, Phillip A.; Vella, Adrian; Zinsmeister, Alan R.

2014-01-01

Background & Aims Acute hyperglycemia delays gastric emptying in patients with diabetes. However, it is not clear whether improved control of glycemia affects gastric emptying in these patients. We investigated whether overnight and short-term (6 months) improvements in control of glycemia affect gastric emptying. Methods We studied 30 patients with poorly controlled type 2 diabetes (levels of glycated hemoglobin >9%). We measured gastric emptying using the [13C]-spirulina platensis breath test on the patients’ first visit (visit 1), after overnight administration of insulin or saline, 1 week later (visit 2), and 6 months after intensive therapy for diabetes. We also measured fasting and post-prandial plasma levels of C-peptide, GLP1, and amylin, as well as autonomic functions. Results At visit 1, gastric emptying was normal in 10 patients, delayed in 14, and accelerated in 6; 6 patients had gastrointestinal symptoms; vagal dysfunction was associated with delayed gastric emptying (P<.05). Higher fasting blood levels of glucose were associated with shorter half-times of gastric emptying (thalf) at visits 1 (r= −0.46, P=.01) and 2 (r= −0.43, P=.02). Although blood levels of glucose were lower after administration of insulin (132±7 mg/dl) than saline (211±15 mg/dl; P=0.0002), gastric emptying thalf was not lower after administration of insulin, compared with saline. After 6 months of intensive therapy, levels of glycated hemoglobin decreased from 10.6%±0.3% to 9%±0.4% (P=.0003), but gastric emptying thalf did not change (92±8 min before, 92±7 min after). Gastric emptying did not correlate with plasma levels of GLP1 and amylin. Conclusions Two-thirds of patients with poorly-controlled type 2 diabetes have mostly asymptomatic yet abnormal gastric emptying. Higher fasting blood levels of glucose are associated with faster gastric emptying. Overnight and sustained (6 months) improvements in glycemic control do not affect gastric emptying. PMID:25041866

75 FR 17859 - Grants to States for Construction or Acquisition of State Home Facilities-Update of Authorized Beds

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-08

... abuse, Alcoholism, Claims, Day care, Dental health, Drug abuse, Foreign relations, Government contracts, Grant programs--health, Grant programs--veterans, Health care, Health facilities, Health professions... FURTHER INFORMATION CONTACT: James F. Burris, MD, Chief Consultant, Geriatrics and Extended Care State...

9 CFR 3.75 - Housing facilities, general.

Code of Federal Regulations, 2012 CFR

2012-01-01

... nonhuman primates come in contact must be spot-cleaned daily and sanitized in accordance with § 3.84 of... bedding, sand, gravel, grass, or other similar material, and planted enclosures must be raked or spot.... Contaminated material must be removed or replaced whenever raking and spot cleaning does not eliminate odors...

Space Transportation Technology Workshop: Propulsion Research and Technology

NASA Technical Reports Server (NTRS)

2000-01-01

This viewgraph presentation gives an overview of the Space Transportation Technology Workshop topics, including Propulsion Research and Technology (PR&T) project level organization, FY 2001 - 2006 project roadmap, points of contact, foundation technologies, auxiliary propulsion technology, PR&T Low Cost Turbo Rocket, and PR&T advanced reusable technologies RBCC test bed.

Sand fly control in Kenya with residual pesticide application on HESCO barriers

USDA-ARS?s Scientific Manuscript database

US military operations in hot-arid regions still face significant impacts from mosquito and sand fly vectors of diseases. Personal protective measures (PPM) such as DEET or treated bed nets and clothing can reduce contact with disease vectors and nuisance insects; however, irregular use of PPM coupl...

Effect of proximal vagotomy and Roux-en-Y diversion on gastric emptying kinetics in asymptomatic patients.

PubMed

Urbain, J L; Penninckx, F; Siegel, J A; Vandenborre, P; Van Cutsem, E; Vandenmaegdenbergh, V; De Roo, M

1990-10-01

The role of the distal stomach in gastric emptying was studied. Ten patients with proximal gastric vagotomy (PV) and 10 age-matched patients with Roux-en-Y gastro-jejunostomy (R-Y) were compared with 10 healthy controls. Gastric emptying of solids and liquids was determined by the use of Tc-99m SC scrambled eggs and In-111 DTPA. In PV, gastric emptying of both solids and liquids was delayed; the prolongation with solids was mainly accounted for by an abnormal lag phase. In R-Y patients, no lag phase was observed, and the solid emptying curve pattern was characterized by early rapid emptying followed by very slow emptying. Both the solid and liquid phases were prolonged. The lag phase is affected by proximal vagotomy and is mainly determined by the distal stomach, which appears to be essential for normal emptying.

Gastric pouch emptying of solid food in patients with successful and unsuccessful weight loss after Roux-en-Y gastric bypass surgery.

PubMed

Deden, Laura N; Cooiman, Mellody I; Aarts, Edo O; Janssen, Ignace M C; Gotthardt, Martin; Hendrickx, Baudewijn W; Berends, Frits J

2017-11-01

After Roux-en-Y gastric bypass (RYGB), approximately 10% of patients have insufficient weight loss (excess body mass index loss<50%). Gastric pouch emptying may have a role in weight loss. To compare pouch emptying of patients with poor weight loss and patients with successful weight loss after RYGB. A research-intensive nonacademic hospital and center of expertise in bariatric surgery in the Netherlands METHODS: Female patients were included from among patients with the least (poor weight loss group [P-WL]) and the most weight loss (successful weight loss group [S-WL]) in our center 2 years after RYGB. Pouch emptying scintigraphy was performed after ingestion of a radiolabeled solid meal. Emptying curves, intestinal content (IC) at meal completion and after 15, 30, 45, and 60 minutes, half emptying time, and maximal pouch emptying rate were compared. Five individuals were included in P-WL and 5 in S-WL, on average 2.5 ± .3 years after RYGB. Total weight loss was 18 ± 4.1% in P-WL and 44 ± 5.7% in S-WL (P<.001). In P-WL, a fast initial pouch emptying and exponential emptying curve was observed, compared with a slower initial emptying and more linear curve in S-WL. Faster emptying in P-WL was also shown by a larger IC meal (42 ± 18% versus 4.0 ± 3.3%,), IC 15 (76 ± 15% versus 35 ± 22%), and IC 30 (85 ± 12% versus 54 ± 25%), and a greater maximal pouch emptying rate (17 ± 4.7 versus 5.6 ± 3.4%/min) compared with S-WL (P<.05). A linear correlation was found between total weight loss and maximal pouch emptying rate (Pearson R = .82, P = .004). Pouch emptying for solid food was faster in patients with the least weight loss compared with patients with the most weight loss after RYGB. If pouch emptying is an important mechanism in weight loss, altering the pouch outlet may improve poor weight loss management. Copyright © 2017 American Society for Bariatric Surgery. Published by Elsevier Inc. All rights reserved.

Late Holocene coastal stratigraphy of Sitkinak Island reveals Aleutian-Alaska megathrust earthquakes and tsunamis southwest of Kodiak Island

NASA Astrophysics Data System (ADS)

Nelson, A. R.; Briggs, R. W.; Kemp, A.; Haeussler, P. J.; Engelhart, S. E.; Dura, T.; Angster, S. J.; Bradley, L.

2012-12-01

Uncertainty in earthquake and tsunami prehistory of the Aleutian-Alaska megathrust westward of central Kodiak Island limit assessments of southern Alaska's earthquake hazard and forecasts of potentially damaging tsunamis along much of North America's west coast. Sitkinak Island, one of the Trinity Islands off the southwest tip of Kodiak Island, lies at the western end of the rupture zone of the 1964 Mw9.2 earthquake. Plafker reports that a rancher on the north coast of Sitkinak Island observed ~0.6 m of shoreline uplift immediately following the 1964 earthquake, and the island is now subsiding at about 3 mm/yr (PBO GPS). Although a high tsunami in 1788 caused the relocation of the first Russian settlement on southwestern Kodiak Island, the eastern extent of the megathrust rupture accompanying the tsunami is uncertain. Interpretation of GPS observations from the Shumagin Islands, 380 km southwest of Kodiak Island, suggests an entirely to partially creeping megathrust in that region. Here we report the first stratigraphic evidence of tsunami inundation and land-level change during prehistoric earthquakes west of central Kodiak Island. Beneath tidal and freshwater marshes around a lagoon on the south coast of Sitkinak Island, 27 cores and tidal outcrops reveal the deposits of four to six tsunamis in 2200 years and two to four abrupt changes in lithology that may correspond with coseismic uplift and subsidence over the past millennia. A 2- to 45-mm-thick bed of clean to peaty sand in sequences of tidal sediment and freshwater peat, identified in more than one-half the cores as far inland as 1.5 km, was probably deposited by the 1788 tsunami. A 14C age on Scirpus seeds, double 137Cs peaks at 2 cm and 7 cm depths (Chernobyl and 1963?), a consistent decline in 210Pb values, and our assumption of an exponential compaction rate for freshwater peat, point to a late 18th century age for the sand bed. Initial 14C ages suggest that two similar extensive sandy beds, identified in eight cores at higher tidal and freshwater sites, date from about 1.5 ka and 2.0 ka, respectively. A younger silty sand bed, <10 cm beneath the now-eroding low marsh around the lagoon, may record the 1964 tsunami. Correlations of two to three other sandy beds are too uncertain to infer their deposition by tsunamis. Stratigraphic contacts found only in cores and outcrops of the <0.8- to 1-ka tidal section fringing the lagoon may mark coseismic uplift (peat over tidal mud, sometimes with intervening sand) or subsidence (tidal mud over peat, sometimes with intervening sand). We collected samples of modern tidal foraminifera along three elevational transects for the baseline dataset needed to use fossil assemblages to measure the amount of uplift or subsidence recorded by contacts. Foraminiferal assemblages above and below one contact confirm rapid uplift a few hundred years before the 1788 tsunami, but cores are too few to correlate this contact with any of the sandy beds that we infer were deposited by tsunamis farther inland. These initial results demonstrate the promise of this previously unexplored island and similar sites for using stratigraphic evidence of sudden land-level changes and high tsunamis to map prehistoric ruptures of the Aleutian-Alaskan megathrust.

Radioactivity and uranium content of the Sharon Springs member of the Pierre shale and associated rocks in western Kansas and eastern Colorado

USGS Publications Warehouse

Landis, Edwin R.

1955-01-01

As a part of the Geological Survey's program of investigating uranium-bearing carbonaceous rocks on behalf of the Division of Raw Materials of the U.S. Atomic Energy Commission, a reconnaissance of the Sharon Springs member of the Pierre shale in western Kansas and eastern Colorado was conducted during 1954. The Sharon Springs member of the Pierre shale and its lateral equivalents ranges from 155 to about 500 feet in thickness and generally contains about 0.001 percent uranium, but some beds contain larger amounts. A 6-foot thick shale bed in Cheyenne County, Colo., contains about 0.006 percent uranium, a 4 1/2-foot thick sequence of beds in Crowley County, Colo., is estimated to contain between 0.004 and 0.005 percent uranium, and a 3 1/2-foot thick sequence of beds in Kiowa County, Colo., contains about 0.004 percent uranium. At several outcrop localities, sequences of beds as much as 9 1/2 feet thick contain about 0.003 percent uranium. Data from wells indicate that the 4 1/2-foot thick sequence of beds in Crowley County, Colo., may have a lateral extent of at least 5 1/2 miles. A gamma-ray log of a well in Yuma County, Colo., indicates the presence of a sequence of beds 66 feet thick which contains 0.005 to 0.010 percent equivalent uranium. No definite pattern of areal distribution of radioactivity and uranium content in the Sharon Springs is indicated by available data. Lateral variation in uranium content of individual beds was not noted in outcrops, which seldom extend more than 150 feet, but subsurface data from gamma-ray logs of wells indicate that both the maximum radioactivity and the thickness of radioactive beds are variable within distances of a few miles. Vertical variation in radioactivity and uranium content of the more radioactive beds is usually abrupt, but in the rocks as a whole the range of uranium content is so small that large variations in content are absent. In most of the gamma-ray logs examined there is only part of the sequence of rocks comprising the Pierre shale and Niobrara formation that exhibits radioactivity in excess of the average radioactivity of the two formations. Comparison of features of gamma-ray logs of wells in north-eastern Colorado suggests that the most radioactive part referred to above is a laterally correlatable sequence of beds. The stratigraphic position of the radioactive unit relative to the Pierre shale-Niobrara formation contact in oil industry scout reports, as identified from electric logs and wells, is variable within short distances. This may indicate that some of the Pierre-Niobrara contacts picked from electric logs may not correspond to the boundary that would be selected by examination of the rocks themselves, or may indicate that there is a facies relationship between teh lowermost part of the Pierre shale and the uppermost part of the Niobrara formation.

Impact on mortality of prompt admission to critical care for deteriorating ward patients: an instrumental variable analysis using critical care bed strain.

PubMed

Harris, Steve; Singer, Mervyn; Sanderson, Colin; Grieve, Richard; Harrison, David; Rowan, Kathryn

2018-05-07

To estimate the effect of prompt admission to critical care on mortality for deteriorating ward patients. We performed a prospective cohort study of consecutive ward patients assessed for critical care. Prompt admissions (within 4 h of assessment) were compared to a 'watchful waiting' cohort. We used critical care strain (bed occupancy) as a natural randomisation event that would predict prompt transfer to critical care. Strain was classified as low, medium or high (2+, 1 or 0 empty beds). This instrumental variable (IV) analysis was repeated for the subgroup of referrals with a recommendation for critical care once assessed. Risk-adjusted 90-day survival models were also constructed. A total of 12,380 patients from 48 hospitals were available for analysis. There were 2411 (19%) prompt admissions (median delay 1 h, IQR 1-2) and 9969 (81%) controls; 1990 (20%) controls were admitted later (median delay 11 h, IQR 6-26). Prompt admissions were less frequent (p < 0.0001) as strain increased from low (22%), to medium (15%) to high (9%); the median delay to admission was 3, 4 and 5 h respectively. In the IV analysis, prompt admission reduced 90-day mortality by 7.4% (95% CI 1.7-18.5%, p = 0.117) overall, and 16.2% (95% CI 1.1-31.3%, p = 0.036) for those recommended for critical care. In the risk-adjust survival model, 90-day mortality was similar. After allowing for unobserved prognostic differences between the groups, we find that prompt admission to critical care leads to lower 90-day mortality for patients assessed and recommended to critical care.

Agoraphobia and Melancholia: Thoughts on Milrod's "Emptiness in Agoraphobia Patients".

PubMed

Yates, Sheena

2015-08-01

Milrod (2007) identifies persistent emptiness in agoraphobic patients whose symptoms of anxiety and avoidance have remitted. To this important identification, a number of critical considerations may be raised regarding the meanings of emptiness in the psychoanalytic clinic. Milrod's admonishment to distinguish between an emptiness that indicates a deficit in the structure and stability of self-representation, and an emptiness that is strictly defensive, is a case in point. While much of the literature supports an interpretation of emptiness as a defense against overwhelming rage, these patients' assertions and experiences of emptiness can be better explained by the presence of traumatic, unmourned losses. Several explanations are offered as to why agoraphobic patients, in particular, defend unconsciously against mourning. © 2015 by the American Psychoanalytic Association.

Fluidized bed coupled rotary reactor for nanoparticles coating via atomic layer deposition

NASA Astrophysics Data System (ADS)

Duan, Chen-Long; Liu, Xiao; Shan, Bin; Chen, Rong

2015-07-01

A fluidized bed coupled rotary reactor has been designed for coating on nanoparticles (NPs) via atomic layer deposition. It consists of five major parts: reaction chamber, dosing and fluidizing section, pumping section, rotary manipulator components, as well as a double-layer cartridge for the storage of particles. In the deposition procedure, continuous fluidization of particles enlarges and homogenizes the void fraction in the particle bed, while rotation enhances the gas-solid interactions to stabilize fluidization. The particle cartridge presented here enables both the fluidization and rotation acting on the particle bed, demonstrated by the analysis of pressure drop. Moreover, enlarged interstitials and intense gas-solid contact under sufficient fluidizing velocity and proper rotation speed facilitate the precursor delivery throughout the particle bed and consequently provide a fast coating process. The cartridge can ensure precursors flowing through the particle bed exclusively to achieve high utilization without static exposure operation. By optimizing superficial gas velocities and rotation speeds, minimum pulse time for complete coating has been shortened in experiment, and in situ mass spectrometry showed the precursor usage can reach 90%. Inductively coupled plasma-optical emission spectroscopy results suggested a saturated growth of nanoscale Al2O3 films on spherical SiO2 NPs. Finally, the uniformity and composition of the shells were characterized by high angle annular dark field-transmission electron microscopy and energy dispersive X-ray spectroscopy.

Deproteinized bovine bone mineral particles and osseointegration of implants without primary bone contact: an experimental study in dogs.

PubMed

Sivolella, Stefano; Bressan, Eriberto; Salata, Luiz A; Quiñones, Maria E; Lang, Niklaus P; Botticelli, Daniele

2014-03-01

To evaluate the influence on osseointegration of Deproteinized bovine bone mineral (DBBM) particles used to fill defects of at least 1 mm around implants having no primary contact with bone. Premolars and first molars were extracted bilaterally from the mandible of six Labrador dogs. After 3 months of healing, mucoperiosteal full-thickness flaps were elevated, and one recipient site was prepared in the molar region of each hemi-mandible to place implants. These were installed with a deliberate circumferential and periapical space to the bone walls of 1.2 mm. All implants were stabilized with passive fixation plates to maintain the implants in situ and without any contact with the implant bed. The control sites were left to be filled with coagulum, while at the test sites, the residual gap was filled with DBBM. After 3 months of submerged healing, the animals were sacrificed. Ground sections were prepared and analyzed histomorphometrically. Mineralized bone-to-implant contact was 4.0% and 3.9% for control and test sites, respectively. The width of the residual defects was 0.48 mm and 0.88 mm at the control and test sites, respectively. The percentage of implant surface covered by a layer of dense connective tissue of 0.12 mm of width on average was 84.9% and 88.5% at the control and test sites, respectively. A minor and not predictable degree of contact or distance osteogenesis was obtained on the implant surface when primary contact of the implant surface with the implant bed had deliberately been avoided. DBBM grafting of the artificial gap did not favor osseointegration. Neither did it enhance the ability to bridge the gap with newly formed bone in an artificial defect wider than 1 mm. © 2013 John Wiley & Sons A/S. Published by Blackwell Publishing Ltd.

Measurement of gastric emptying by intragastric gamma scintigraphy.

PubMed

Malbert, C H; Mathis, C; Bobillier, E; Laplace, J P; Horowitz, M

1997-09-01

Gastric emptying is usually measured in animals and humans by dilution/sampling or external scintigraphy. These methods are either time consuming or require expensive equipment. The capacity of a miniature gamma counter positioned in the stomach to measure emptying of liquid and solid meals was evaluated. In eight conscious pigs fitted with gastric and duodenal cannulae, gastric emptying of saline (500 mL), dextrose (20%, 500 mL), porridge (300 g) and scrambled eggs (300 g), all labelled with 3.5 MBq 99mTC, was evaluated. When positioned in the antrum the probe was unable to quantify gastric emptying. In contrast, measurements of the fractional emptying of saline over 4-min periods by the probe positioned in the corpus and quantification of radioactivity in the duodenal effluent correlated closely (r = 0.88, P < 0.05). Gastric emptying (50% emptying time) of saline and both solid meals measured by the probe was not significantly different from quantification of the duodenal effluent volume. No difference was observed also for the dextrose meal but only while gastric acid secretion was suppressed by omeprazole. We conclude that an intragastric gamma counter permits measurement of gastric emptying of homogeneous meals provided meal stimulation of gastric secretion was not extensive. This was possible probably by monitoring emptying from the proximal stomach.

Down-flow moving-bed gasifier with catalyst recycle

DOEpatents

Halow, John S.

1999-01-01

The gasification of coal and other carbonaceous materials by an endothermic gasification reaction is achieved in the presence of a catalyst in a down-flow, moving-bed gasifier. Catalyst is removed along with ash from the gasifier and is then sufficiently heated in a riser/burner by the combustion of residual carbon in the ash to volatilize the catalyst. This volatilized catalyst is returned to the gasifier where it uniformly contacts and condenses on the carbonaceous material. Also, the hot gaseous combustion products resulting from the combustion of the carbon in the ash along with excess air are introduced into the gasifier for providing heat energy used in the endothermic reaction.

A Method for Evaluating Insecticide Efficacy against Bed Bug, Cimex lectularius, Eggs and First Instars.

PubMed

Campbell, Brittany E; Miller, Dini M

2017-03-15

Standard toxicity evaluations of insecticides against insect pests are primarily conducted on adult insects. Evaluations are based on a dose-response or concentration-response curve, where mortality increases as the dose or concentration of an insecticide is increased. Standard lethal concentration (LC50) and lethal dose (LD50) tests that result in 50% mortality of a test population can be challenging for evaluating toxicity of insecticides against non-adult insect life stages, such as eggs and early instar or nymphal stages. However, this information is essential for understanding insecticide efficacy in all bed bug life stages, which affects control and treatment efforts. This protocol uses a standard dipping bioassay modified for bed bug eggs and a contact insecticidal assay for treating nymphal first instars. These assays produce a concentration-response curve to further quantify LC50 values for insecticide evaluations.

Two-dimensional coupled mathematical modeling of fluvial processes with intense sediment transport and rapid bed evolution

NASA Astrophysics Data System (ADS)

Yue, Zhiyuan; Cao, Zhixian; Li, Xin; Che, Tao

2008-09-01

Alluvial rivers may experience intense sediment transport and rapid bed evolution under a high flow regime, for which traditional decoupled mathematical river models based on simplified conservation equations are not applicable. A two-dimensional coupled mathematical model is presented, which is generally applicable to the fluvial processes with either intense or weak sediment transport. The governing equations of the model comprise the complete shallow water hydrodynamic equations closed with Manning roughness for boundary resistance and empirical relationships for sediment exchange with the erodible bed. The second-order Total-Variation-Diminishing version of the Weighted-Average-Flux method, along with the HLLC approximate Riemann Solver, is adapted to solve the governing equations, which can properly resolve shock waves and contact discontinuities. The model is applied to the pilot study of the flooding due to a sudden outburst of a real glacial-lake.

Endoscopic Evaluation of Gastric Emptying and Effect of Mosapride Citrate on Gastric Emptying

PubMed Central

Jung, In Su; Kim, Jie-Hyun; Lee, Hwal Youn; Lee, Sang In

2010-01-01

Purpose Gastric emptying has been evaluated by scintigraphy in spite of its limitations of time consumption, cost, and danger of radioisotope. Endoscopy is a simple technique, however, its validation for gastric emptying and quantification of food has not yet been investigated. The aim of our study was to assess endoscopic gastric emptying compared with scintigraphy and radiopaque markers (ROMs) studies. We also investigated the effect of a single dose of mosapride on gastric emptying. Materials and Methods Fifteen healthy volunteers underwent scintigraphy. Next day, subjects received a standard solid meal with ROMs and underwent endoscopy and simple abdomen X-ray after 3 hrs. After one week, the same procedure was repeated after ingestion of mosapride (5 mg for group 1, n = 8; 10 mg for group 2, n = 7) 15 min before the meal. Quantification of gastric residue by endoscopy was scored from 0 to 3, and the scores were added up. Results All subjects completed the study without any complication. The gastric emptying rate [T1/2 (min)] was in normal range (65.6 ± 12.6 min). Endoscopic gastric emptying was correlated significantly with gastric clearance of ROMs (r = 0.627, p = 0.012). Endoscopic gastric emptying and gastric clearance of ROMs after administration of mosapride showed significant differences in the 10 mg group (p < 0.05). Conclusion Endoscopy can evaluate gastric emptying safely and simply on an outpatient basis. A 10 mg dose of mosapride enhanced gastric emptying, assessed by both endoscopy and ROMs. PMID:20046511

Catastrophic health expenditure: a comparative analysis of empty-nest and non-empty-nest households with seniors in Shandong, China.

PubMed

Yang, Tingting; Chu, Jie; Zhou, Chengchao; Medina, Alexis; Li, Cuicui; Jiang, Shan; Zheng, Wengui; Sun, Liyuan; Liu, Jing

2016-07-05

The aim of this study was to compare the catastrophic health expenditure (CHE) prevalence and its determinants between empty-nest and non-empty-nest elderly households. Shandong province of China. A total of 2761 elderly households are included in the analysis. CHE incidence among elderly households was 44.9%. The CHE incidence of empty-nest singles (59.3%, p=0.000, OR=3.19) and empty-nest couples (52.9%, p=0.000, OR=2.45) are both statistically higher than that of non-empty-nest elderly households (31.4%). An inverse association was observed between CHE incidence and income level in all elderly household types. Factors including 1 or more household elderly members with non-communicable chronic diseases in the past 6 months, 1 or more elderly household members being hospitalised in the past year and lower household income, are significant risk factors for CHE in all 3 household types (p<0.05). Health insurance status was found to be a significant determinant of CHE among empty-nest singles and non-empty-nest households (p<0.05). CHE incidence among elderly households is high in China. Empty-nest households are at higher risk for CHE than non-empty-nest households. Based on these findings, we suggest that special insurance be developed to broaden the coverage of health services and heighten the reimbursement rate for empty-nest elderly in the existing health insurance schemes. Financial and social protection interventions are also essential for identified at-risk subgroups among different types of elderly households. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Catastrophic health expenditure: a comparative analysis of empty-nest and non-empty-nest households with seniors in Shandong, China

PubMed Central

Yang, Tingting; Chu, Jie; Zhou, Chengchao; Medina, Alexis; Li, Cuicui; Jiang, Shan; Zheng, Wengui; Sun, Liyuan; Liu, Jing

2016-01-01

Objective The aim of this study was to compare the catastrophic health expenditure (CHE) prevalence and its determinants between empty-nest and non-empty-nest elderly households. Setting Shandong province of China. Participants A total of 2761 elderly households are included in the analysis. Results CHE incidence among elderly households was 44.9%. The CHE incidence of empty-nest singles (59.3%, p=0.000, OR=3.19) and empty-nest couples (52.9%, p=0.000, OR=2.45) are both statistically higher than that of non-empty-nest elderly households (31.4%). An inverse association was observed between CHE incidence and income level in all elderly household types. Factors including 1 or more household elderly members with non-communicable chronic diseases in the past 6 months, 1 or more elderly household members being hospitalised in the past year and lower household income, are significant risk factors for CHE in all 3 household types (p<0.05). Health insurance status was found to be a significant determinant of CHE among empty-nest singles and non-empty-nest households (p<0.05). Conclusions CHE incidence among elderly households is high in China. Empty-nest households are at higher risk for CHE than non-empty-nest households. Based on these findings, we suggest that special insurance be developed to broaden the coverage of health services and heighten the reimbursement rate for empty-nest elderly in the existing health insurance schemes. Financial and social protection interventions are also essential for identified at-risk subgroups among different types of elderly households. PMID:27381206

Exploring the potential of fungi for methane abatement: Performance evaluation of a fungal-bacterial biofilter.

PubMed

Lebrero, Raquel; López, Juan Carlos; Lehtinen, Iiro; Pérez, Rebeca; Quijano, Guillermo; Muñoz, Raúl

2016-02-01

Despite several fungal strains have been retrieved from methane-containing environments, the actual capacity and role of fungi on methane abatement is still unclear. The batch biodegradation tests here performed demonstrated the capacity of Graphium sp. to co-metabolically biodegrade methane and methanol. Moreover, the performance and microbiology of a fungal-bacterial compost biofilter treating methane at concentrations of ∼2% was evaluated at empty bed residence times of 40 and 20 min under different irrigation rates. The daily addition of 200 mL of mineral medium resulted in elimination capacities of 36.6 ± 0.7 g m(-3) h(-1) and removal efficiencies of ≈90% at the lowest residence time. The indigenous fungal community of the compost was predominant in the final microbial population and outcompeted the inoculated Graphium sp. during biofilter operation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performances of two biotrickling filters in treating H₂S-containing waste gases and analysis of corresponding bacterial communities by pyrosequencing.

PubMed

Li, Jianjun; Ye, Guangyun; Sun, Duanfang; Sun, Guoping; Zeng, Xiaowei; Xu, Jian; Liang, Shizhong

2012-09-01

Two identical biotrickling filters named BTFa and BTFb were run in parallel to examine their performances in removing hydrogen sulfide. BTFa was filled with ceramic granules, and BTFb was filled with volcanic rocks. The results showed that BTFb was more robust than BTFa under acidic conditions. At empty bed residence times (EBRTs) of 20 and 15 s, the removal efficiency of BTFa was close to 100%. At EBRTs of 10 and 5 s, the removal efficiency of BTFa slightly decreased. The removal efficiencies of BTFa decreased by different degrees at the end of each stage, dropping to 94%, 81%, 60%, and 71%, respectively. However, the H(2)S removal efficiency in BTFb consistently reached 99% throughout the experiment. Pyrosequencing analyses indicated that members of Thiomonas dominated in both BTFs, but the relative abundance of Acidithiobacillus was higher in BTFb than in BTFa.

The enuretic episode--a complete micturition from a bladder with normal capacity? A critical reappraisal of the definition.

PubMed

Rasmussen, P V; Kirk, J; Rittig, S; Djurhuus, J C

1997-01-01

Fifty-five normal children, aged between 7 and 12 years, were hospitalised for four consecutive nights. On three of these nights, the subjects received 25 ml/kg body weight of fluid prior to bedtime. Such fluid-loading provoked 28 enuresis-like episodes in 17 children, most of which occurred during the first few hours of sleep. The incidence of these enuretic events decreased with increasing age, more boys than girls were affected, there was a statistically significant correlation between total enuresis volume and nocturia volume, and the micturition was frequently incomplete, leaving large volumes of residual urine in the bladder. It was concluded that if nocturnal urine production exceeds bladder capacity, enuresis may be provoked, even in children who do not normally wet the bed. Furthermore, the definition of nocturnal enuresis as a complete emptying of the bladder during sleep may need revision.

Delayed gastric emptying of both the liquid and solid components of a meal in chronic liver disease.

PubMed

Galati, J S; Holdeman, K P; Dalrymple, G V; Harrison, K A; Quigley, E M

1994-05-01

To evaluate gastric emptying in patients with chronic liver disease and portal hypertension. We measured gastric emptying of both the liquid and solid components of a meal in 10 consecutive patients with chronic liver disease and portal hypertension, but free of ascites, and 14 age- and sex-matched healthy controls. In the patients with liver disease, relationships between emptying and liver function were examined. To measure gastric emptying, subjects consumed a test meal that consisted of scrambled eggs labeled with 99mTc-sulfur colloid and 4 oz of water labeled with 111In-diethylene triamine pentacetic acid (DTPA). Patients with liver disease and portal hypertension demonstrated delayed emptying of both the liquid (t1/2, min, mean +/- SE, patients vs. 69.4 +/- 19.4 vs. 31.4 +/- 1.8, p < 0.01) and solid (post-lag phase solid emptying: 141 +/- 32.9 vs. 69.8 +/- 4.6, p < 0.006) components of the meal. We could not identify any correlation between gastric emptying and tests of liver function. Gastric emptying is delayed in patients with liver disease and portal hypertension; this abnormal gastric motor function may contribute to the pathophysiology of foregut complaints in this patient population.

Canine gastric emptying of fiber meals: influence of meal viscosity and antroduodenal motility.

PubMed

Russell, J; Bass, P

1985-12-01

Dietary fibers such as psyllium and guar gum have been shown to delay the gastric emptying of liquids and solids, presumably due to an increase in meal viscosity. For liquid test meals containing fats, delayed gastric emptying is associated with a reversal of the usual antral-to-duodenal contractile gradient. The present studies were performed to determine whether the gastric emptying of increasingly viscous psyllium and guar gum meals was associated with antroduodenal motility changes. Dogs were surgically fitted with mid-duodenal cannulas for the measurement of gastric emptying. Strain-gauge force transducers were used to monitor antral and duodenal contractile responses to the test meals. Low-viscosity fiber meals emptied from the stomach rapidly (E 1/2 approximately 10 min) compared with the high-viscosity meals (E 1/2 approximately 40 min). None of the test meals stimulated antral or duodenal motility despite differences in gastric emptying time. Other motor parameters such as the time of reappearance and the duration of the burst interval were also unchanged. We conclude a) as test meals' fiber content and viscosity increase, gastric emptying is slowed; and b) viscosity-related delays in gastric emptying are not due to an effect on postprandial antroduodenal motility.

49 CFR 173.29 - Empty packagings.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Empty packagings. 173.29 Section 173.29... SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.29 Empty packagings. (a) General. Except as otherwise provided in this section, an empty packaging containing only the residue of a...

A 600-year-long stratigraphic record of tsunamis in south-central Chile

USGS Publications Warehouse

Hong, Isabel; Dura, Tina; Ely, Lisa L.; Horton, Benajamin P.; Nelson, Alan R.; Cisternas, Marco; Nikitina, Daria; Wesson, Robert L.

2017-01-01

The stratigraphy within coastal river valleys in south-central Chile clarifies and extends the region’s history of large, earthquakes and accompanying tsunamis. Our site at Quidico (38.1°S, 73.3°W) is located in an overlap zone between ruptures of magnitude 8–9 earthquakes in 1960 and 2010, and, therefore, records tsunamis originating from subduction-zone ruptures north and south of the city of Concepción. Hand-dug pits and cores in a 3-m-thick sequence of freshwater peat in an abandoned meander (a little-examined depositional environment for tsunami deposits) and exposures along the Quidico River show five sand beds that extend as much as 1.2 km inland. Evidence for deposition of the beds by tsunamis includes tabular sand beds that are laterally extensive (>100 m), well sorted, fine upward, have sharp lower contacts, and contain diatom assemblages dominated by brackish and marine taxa. Using eyewitness accounts of tsunami inundation, 137Cs analyses, and 14C dating, we matched the upper four sand beds with historical tsunamis in 2010, 1960, 1835, and 1751. The oldest prehistoric bed dates to 1445–1490 CE and correlates with lacustrine and coastal records of similar-aged earthquakes and tsunamis in south-central Chile.

Comprehensive Comparison between Empty Nest and Non-Empty Nest Elderly: A Cross-Sectional Study among Rural Populations in Northeast China

PubMed Central

Chang, Ye; Guo, Xiaofan; Guo, Liang; Li, Zhao; Yang, Hongmei; Yu, Shasha; Sun, Guozhe; Sun, Yingxian

2016-01-01

This study aimed to comprehensively compare the general characteristics, lifestyles, serum parameters, ultrasonic cardiogram (UCG) parameters, depression, quality of life, and various comorbidities between empty nest and non-empty nest elderly among rural populations in northeast China. This analysis was based on our previous study which was conducted from January 2012 to August 2013, using a multistage, stratified, random cluster sampling scheme. The final analyzed sample consisted of 3208 participants aged no less than 60 years, which was further classified into three groups: non-empty nest group, empty nest group (living as a couple), and empty nest group (living alone). More than half of the participants were empty nest elderly (60.5%). There were no significant statistical differences for serum parameters, UCG parameters, lifestyles, dietary pattern, and scores of Patient Health Questionnaire-9 (PHQ-9) and World Health Organization Quality of Life questionnaire, abbreviated version (WHOQOL-BREF) among the three groups. Empty nest elderly showed no more risk for comorbidities such as general obesity, abdominal obesity, hyperuricemia, hyperhomocysteinemia, diabetes, dyslipidemia, left atrial enlargement (LAE), and stroke. Our study indicated that empty nest elderly showed no more risk for depression, low quality of life and comorbidities such as general obesity, abdominal obesity, hyperuricemia, hyperhomocysteinemia, diabetes, dyslipidemia, LAE, and stroke among rural populations in northeast China. PMID:27618905

Comprehensive Comparison between Empty Nest and Non-Empty Nest Elderly: A Cross-Sectional Study among Rural Populations in Northeast China.

PubMed

Chang, Ye; Guo, Xiaofan; Guo, Liang; Li, Zhao; Yang, Hongmei; Yu, Shasha; Sun, Guozhe; Sun, Yingxian

2016-08-27

This study aimed to comprehensively compare the general characteristics, lifestyles, serum parameters, ultrasonic cardiogram (UCG) parameters, depression, quality of life, and various comorbidities between empty nest and non-empty nest elderly among rural populations in northeast China. This analysis was based on our previous study which was conducted from January 2012 to August 2013, using a multistage, stratified, random cluster sampling scheme. The final analyzed sample consisted of 3208 participants aged no less than 60 years, which was further classified into three groups: non-empty nest group, empty nest group (living as a couple), and empty nest group (living alone). More than half of the participants were empty nest elderly (60.5%). There were no significant statistical differences for serum parameters, UCG parameters, lifestyles, dietary pattern, and scores of Patient Health Questionnaire-9 (PHQ-9) and World Health Organization Quality of Life questionnaire, abbreviated version (WHOQOL-BREF) among the three groups. Empty nest elderly showed no more risk for comorbidities such as general obesity, abdominal obesity, hyperuricemia, hyperhomocysteinemia, diabetes, dyslipidemia, left atrial enlargement (LAE), and stroke. Our study indicated that empty nest elderly showed no more risk for depression, low quality of life and comorbidities such as general obesity, abdominal obesity, hyperuricemia, hyperhomocysteinemia, diabetes, dyslipidemia, LAE, and stroke among rural populations in northeast China.

Incidence and Impact of Selected Infectious Diseases in Childhood.

ERIC Educational Resources Information Center

Vital and Health Statistics, 1991

1991-01-01

This report provides estimates of the lifetime and annual incidence of certain infectious diseases of children in various demographic groups. Data on the social and health care impact of the diseases in terms of limited activity, days spent in bed, school days lost, contacts with physicians, hospitalizations, surgery, and use of medication are…

21 CFR 173.40 - Molecular sieve resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... water regain), and a particle size of 10 to 300 microns. (b) The molecular sieve resins are thoroughly washed with potable water prior to their first use in contact with food. (c) Molecular sieve resins are used as the gel filtration media in the final purification of partially delactosed whey. The gel bed...

Why does the Conductivity of a Nickel Catalyst Increase during Sulfidation? An Exemplary Study Using an In Operando Sensor Device.

PubMed

Fremerey, Peter; Jess, Andreas; Moos, Ralf

2015-10-23

In order to study the sulfidation of a catalyst fixed bed, an in operando single pellet sensor was designed. A catalyst pellet from the fixed bed was electrically contacted and its electrical response was correlated with the catalyst behavior. For the sulfidation tests, a nickel catalyst was used and was sulfidized with H₂S. This catalyst had a very low conductivity in the reduced state. During sulfidation, the conductivity of the catalyst increased by decades. A reaction from nickel to nickel sulfide occurred. This conductivity increase by decades during sulfidation had not been expected since both nickel and nickel sulfides behave metallic. Only by assuming a percolation phenomenon that originates from a volume increase of the nickel contacts when reacting to nickel sulfides, this effect can be explained. This assumption was supported by sulfidation tests with differently nickel loaded catalysts and it was quantitatively estimated by a general effective media theory. The single pellet sensor device for in operando investigation of sulfidation can be considered as a valuable tool to get further insights into catalysts under reaction conditions.

Analog and numerical experiments investigating force chain influences on bed conditions in granular flows

NASA Astrophysics Data System (ADS)

Estep, J.; Dufek, J.

2013-12-01

Granular flows are fundamental processes in several terrestrial and planetary natural events; including surficial flows on volcanic edifices, debris flows, landslides, dune formation, rock falls, sector collapses, and avalanches. Often granular flows can be two-phase, whereby interstitial fluids occupy void space within the particulates. The mobility of granular flows has received significant attention, however the physics that govern their internal behavior remain poorly understood. Here we extend upon previous research showing that force chains can transmit extreme localized forces to the substrates of free surface granular flows, and we combine experimental and computational approaches to further investigate the forces at the bed of simplified granular flows. Analog experiments resolve discrete bed forces via a photoelastic technique, while numerical experiments validate laboratory tests using discrete element model (DEM) simulations. The current work investigates (1) the role of distributed grain sizes on force transmission via force chains, and (2) how the inclusion of interstitial fluids effects force chain development. We also include 3D numerical simulations to apply observed 2D characteristics into real world perspective, and ascertain if the added dimension alters force chain behavior. Previous research showed that bed forces generated by force chain structures can transiently greatly exceed (by several 100%) the bed forces predicted from continuum approaches, and that natural materials are more prone to excessive bed forces than photoelastic materials due to their larger contact stiffnesses. This work suggests that force chain activity may play an important role in the bed physics of dense granular flows by influencing substrate entrainment. Photoelastic experiment image showing force chains in gravity driven granular flow.

Confirmation of monod model for biofiltration of styrene vapors from waste flue gas.

PubMed

Dehghanzadeh, Reza; Roshani, Babak; Asadi, Mahzar; Fahiminia, Mohammad; Aslhashemi, Ahmad

2012-01-01

The objective of this research was to investigate the kinetic behavior of the biofil¬tration process for the removal of styrene. A three stage compost based biofilter was inoculated with thickened activated sludge. The reaction order rate constants were obtained from continuous experiments and used as the specific growth rate for the Monod equation. The measured concentration profiles show a linear dependence on the bed height in the biofilter at higher loadings, such as 75 and 45 g m-3 h-1. This is the condition of reaction limitation for a reaction with zero-order kinetics. From the experimental data, maximum elimination capac¬ity (ECmax) was estimated to be 44, 40 and 26 g m-3 h-1 at empty bed retention times (EBRTs) of 120, 60 and 30 s, respectively. However, at lower loadings, the measured concentration profile of the biofilter is one of exponential increase, which is the condition of both reaction and diffusion limitations for a reaction with zero-order kinetics. Maximum elimination capacities found from the experimental results were the same as Monod model predictions. Both the experimental re¬sults and the model predictions showed the influence of EBRT on the removal rate of styrene, particularly for the highest loading rate. In terms of the practical applications of the proposed models have the advantage of being simpler than Monod kinetics and Monod kinetics requires a numerical solution.

Ward assessment of SmartIdeas Project: bringing source isolation to the patient.

PubMed

Moore, G; Ali, S; FitzGerald, G; Muzslay, M; Atkinson, S; Smith, S; Cryer, P; Gush, C; Wilson, A P R

2010-10-01

Most UK hospitals lack enough single rooms to provide source isolation for all infected patients. The aim of this study was to test prototype isolation systems on general wards together with specifically designed portable sink units and toilets. Questionnaires were offered to staff, patients and visitors covering ease of use and acceptability. A total of 53 patients were isolated, with concurrent collection of environmental samples and staff hand hygiene audit. Blocking of beds next to infected patients was avoided but patients and staff were concerned about limited space and communication. Hand hygiene compliance on entry or exit to/from an isolated bed space significantly improved [43/76 (56.6%) to 107/147 (72.8%), P<0.05]. Although popular, the toilets were mechanically unreliable. Low levels of microbial contamination (<1-3.4cfu/cm(2)) were present within all isolated bed spaces. The highest colony counts were obtained from high contact sites (e.g. remote controls). Meticillin-resistant Staphylococcus aureus (MRSA) was present at similar levels inside all systems. Although one system was designed to provide airborne as well as contact isolation, MRSA was isolated from air inside and outside the system suggesting poor efficiency of the air door. The finding was confirmed by aerobiology tests at the Health Protection Agency Laboratory, Porton Down, UK. A trial of redesigned units is required to establish efficacy (Trial Identifier: ISRCTN02681602). Copyright 2010 The Hospital Infection Society. All rights reserved.

14 CFR 223.24 - Transportation of empty mail bags.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Transportation of empty mail bags. Any carrier authorized to engage in foreign air transportation may transport in foreign air transportation empty air mail bags from any country to the country of origin of such... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Transportation of empty mail bags. 223.24...

14 CFR 223.24 - Transportation of empty mail bags.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Transportation of empty mail bags. Any carrier authorized to engage in foreign air transportation may transport in foreign air transportation empty air mail bags from any country to the country of origin of such... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Transportation of empty mail bags. 223.24...

14 CFR 223.24 - Transportation of empty mail bags.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Transportation of empty mail bags. Any carrier authorized to engage in foreign air transportation may transport in foreign air transportation empty air mail bags from any country to the country of origin of such... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Transportation of empty mail bags. 223.24...

The stomach, cholecystokinin, and satiety.

PubMed

McHugh, P R; Moran, T H

1986-04-01

The stomach of the rhesus monkey empties liquids in a fashion that varies with the character of the solutions. Physiological saline empties exponentially. Glucose solutions empty biphasically--rapidly for the first minutes, then slowly and proportionately to glucose concentration to deliver glucose calories through the pylorus at a regulated rate (0.4 kcal/min). This prolonged and regulated second phase of gastric emptying depends on intestinal inhibition of the stomach. Cholecystokinin (CCK), a hormone released by food in the intestine, is an inhibitor of gastric emptying. In vitro receptor autoradiography demonstrates CCK receptors to be clustered on the circular muscle of the pylorus. Exogenous CCK, in doses that inhibit gastric emptying, will reduce food intake only if combined with an infusion of saline in the stomach. These observations indicate how gastric distension can be a means for provoking satiety. The variably sustained distension produced by the stomach's slow, calorically regulated emptying could prolong intermeal intervals and thus permit high-calorie meals to inhibit further caloric intake over time. CCK, by directly inhibiting gastric emptying during a meal, could promote gastric distension and so restrict the duration and size of individual meals.

Effect of parenteral administration of erythromycin, tilmicosin, and tylosin on abomasal emptying rate in suckling calves.

PubMed

Nouri, Mohammad; Constable, Peter D

2007-12-01

To determine the effect of parenteral administration of erythromycin, tilmicosin, and tylosin on abomasal emptying rate in suckling calves. 8 male Holstein-Friesian calves < 35 days old. Calves received each of 4 treatments in random order (2 mL of saline [0.9% NaCl] solution, IM [control treatment]; erythromycin, 8.8 mg/kg, IM; tilmicosin, 10 mg/kg, SC; and tylosin, 17.6 mg/kg, IM). Calves were fed 2 L of milk replacer containing acetaminophen (50 mg/kg) 30 minutes later. Jugular venous blood samples and transabdominal ultrasonographic abomasal dimensions were obtained periodically after suckling. Abomasal emptying rate was assessed on the basis of the time to maximal plasma acetaminophen concentration and ultrasonographic determination of the halftime of abomasal emptying. One-tailed Dunnett post tests were conducted whenever the F value for group was significant. Emptying rate was faster for erythromycin, tilimicosin, and tylosin than for the control treatment, as determined on the basis of time to maximal plasma acetaminophen concentration. Ultrasonography indicated that the half-time of abomasal emptying was significantly shorter for erythromycin than for the control treatment. Tylosin and tilmicosin accelerated the abomasal emptying rate, but not significantly, relative to the emptying rate for the control treatment. Administration of erythromycin, tilmicosin, and tylosin at the label dosage increased abomasal emptying rate in calves. The clinical importance of an increase in abomasal emptying rate in cattle remains to be determined.

Relation between gastric emptying rate and energy intake in children compared with adults.

PubMed Central

Maes, B D; Ghoos, Y F; Geypens, B J; Hiele, M I; Rutgeerts, P J

1995-01-01

Measurement of gastric emptying rate of solids in children is difficult because the available methods are either invasive or induce a substantial radiation burden. In this study the newly developed 13C octanoic acid breath test was used to examine the gastric emptying rate of solids and milk in healthy children and to compare gastric emptying in children and adults. Fifteen healthy children and three groups of nine healthy adults were studied, using three different test meals labelled with 50 mg of 13C octanoic acid: a low caloric pancake (150 kcal), a high caloric pancake (250 kcal), and 210 ml of milk (134 kcal). Breath samples were taken before and at regular intervals after ingestion of the test meal, and analysed by isotope ratio mass spectrometry. The gastric emptying parameters were derived from the 13CO2 excretion curves by non-linear regression analysis. No significant difference was found between children and adults in the emptying rate of the low caloric solid test meal. In children as well as in adults, increasing the energy content of the solid meal resulted in a significantly slower emptying rate. The milk test meal, however, was emptied at a faster rate in adults and at slower rate in children compared with the low caloric solid test meal. Moreover, the emptying rate of milk in children was significantly slower than in adults. In conclusion, a similar gastric emptying rate of solids but a slower emptying of full cream milk was shown in children of school age compared with adults, using the non-radioactive 13C octanoic acid breath test. PMID:7883214

Efficient Capsid Antigen Presentation From Adeno-Associated Virus Empty Virions In Vivo.

PubMed

Pei, Xiaolei; Earley, Lauriel Freya; He, Yi; Chen, Xiaojing; Hall, Nikita Elexa; Samulski, Richard Jude; Li, Chengwen

2018-01-01

Adeno-associated virus (AAV) vectors have been successfully applied in clinical trials for hemophilic patients. Although promising, the clinical results suggest that the capsid-specific CD8+T cell response has a negative effect on therapeutic success. In an in vitro analysis using an engineered AAV virus carrying immune-dominant SIINFEKL peptide in the capsid backbone, we have previously demonstrated that capsid antigen presentation from full (genome containing) AAV capsids requires endosome escape and is proteasome dependent and that no capsid antigen presentation is induced from empty virions. In the present study, we examined capsid antigen presentation from administration of empty virions in animal models. In wild-type mice, similar to AAV full particles, capsid antigen presentation from AAV empty virion infection was dose dependent, and the kinetics studies showed that antigen presentation was detected from 2 to 40 days after AAV empty virion administration. In the transporter associated with antigen processing 1 deficient (TAP-/-) mice, capsid antigen presentation was inhibited from both AAV full and empty virions, but higher inhibition was achieved from AAV full particle administration than that from empty virions. This indicates that the pathway of capsid antigen presentation from AAV transduction is dependent on proteasome-mediated degradation of AAV capsids (mainly for full particles) and that the endosomal pathway may also play a role in antigen presentation from empty particles but not full virions. The capsid antigen presentation efficiency from AAV preparations was positively correlated with the amount of empty virions contaminated with full particles. Collectively, the results indicate that contamination of AAV empty virions induces efficient antigen presentation in vivo and the mechanism of capsid antigen presentation from empty virions involves both endosomal and proteasomal pathways. The elucidation of capsid antigen presentation from AAV empty virions may allow us to rationally design effective strategies to prevent elimination of AAV transduced target cells by capsid specific CD8+ T cells.

Efficient Capsid Antigen Presentation From Adeno-Associated Virus Empty Virions In Vivo

PubMed Central

Pei, Xiaolei; Earley, Lauriel Freya; He, Yi; Chen, Xiaojing; Hall, Nikita Elexa; Samulski, Richard Jude; Li, Chengwen

2018-01-01

Adeno-associated virus (AAV) vectors have been successfully applied in clinical trials for hemophilic patients. Although promising, the clinical results suggest that the capsid-specific CD8+T cell response has a negative effect on therapeutic success. In an in vitro analysis using an engineered AAV virus carrying immune-dominant SIINFEKL peptide in the capsid backbone, we have previously demonstrated that capsid antigen presentation from full (genome containing) AAV capsids requires endosome escape and is proteasome dependent and that no capsid antigen presentation is induced from empty virions. In the present study, we examined capsid antigen presentation from administration of empty virions in animal models. In wild-type mice, similar to AAV full particles, capsid antigen presentation from AAV empty virion infection was dose dependent, and the kinetics studies showed that antigen presentation was detected from 2 to 40 days after AAV empty virion administration. In the transporter associated with antigen processing 1 deficient (TAP−/−) mice, capsid antigen presentation was inhibited from both AAV full and empty virions, but higher inhibition was achieved from AAV full particle administration than that from empty virions. This indicates that the pathway of capsid antigen presentation from AAV transduction is dependent on proteasome-mediated degradation of AAV capsids (mainly for full particles) and that the endosomal pathway may also play a role in antigen presentation from empty particles but not full virions. The capsid antigen presentation efficiency from AAV preparations was positively correlated with the amount of empty virions contaminated with full particles. Collectively, the results indicate that contamination of AAV empty virions induces efficient antigen presentation in vivo and the mechanism of capsid antigen presentation from empty virions involves both endosomal and proteasomal pathways. The elucidation of capsid antigen presentation from AAV empty virions may allow us to rationally design effective strategies to prevent elimination of AAV transduced target cells by capsid specific CD8+ T cells. PMID:29725339

Gender Difference of Gastric Emptying in Healthy Volunteers and Patients with Functional Dyspepsia.

PubMed

Mori, Hideki; Suzuki, Hidekazu; Matsuzaki, Juntaro; Taniguchi, Kanami; Shimizu, Toshiyuki; Yamane, Tsuyoshi; Masaoka, Tatsuhiro; Kanai, Takanori

2017-01-01

Delayed gastric emptying is one of the reasons why functional dyspepsia (FD) occurs. The 13C-acetate breath test is widely used to evaluate gastric emptying. Nevertheless, the standard value of 13C-acetate breath test has not taken into account the gender difference of gastric emptying among healthy individuals. The main aim of this study was to readjust the standard value of 13C-acetate breath test in the light of gender differences. In addition, we clarified the prevalence and clinical characteristics of delayed gastric emptying in patients with FD using the modified standard values of 13C-acetate breath test. Fifty-two healthy individuals and 126 patients with patients with FD were enrolled. Gastric emptying was evaluated by the 13C-acetate breath test. The cut-off points of Tmax for the diagnosis of delayed gastric emptying were determined on the basis of results from healthy individuals making a distinction of genders. Gastroesophageal reflux symptoms, dyspeptic symptoms, scores of anxiety and depression, age, body mass index (BMI), smoking and alcohol consumption were compared between the delayed gastric emptying group and the non-delayed gastric emptying group. Since gastric emptying was delayed in healthy women compared with that in healthy men (Tmax, 53.6 ± 19.3 vs. 42.7 ± 16.9 min, p = 0.04), we set the cut-off points of Tmax at 60 min in men and at 75 min in women. In patients with FD, the prevalence of delayed gastric emptying was not different between men and women with the modified standard values of 13C-acetate breath test. (31.0 vs. 27.4%, p = 0.68). BMI was lower in the delayed gastric emptying group than in the non-delayed group among the male patients. Reflux symptoms were more severe in delayed gastric emptying group than in the non-delayed group among the female patients. The standard values of 13C-acetate breath test should be modified bearing the gender difference in mind. It provides us more appropriate information to understand the mechanisms of FD. © 2016 S. Karger AG, Basel.

Down-flow moving-bed gasifier with catalyst recycle

DOEpatents

Halow, J.S.

1999-04-20

The gasification of coal and other carbonaceous materials by an endothermic gasification reaction is achieved in the presence of a catalyst in a down-flow, moving-bed gasifier. Catalyst is removed along with ash from the gasifier and is then sufficiently heated in a riser/burner by the combustion of residual carbon in the ash to volatilize the catalyst. This volatilized catalyst is returned to the gasifier where it uniformly contacts and condenses on the carbonaceous material. Also, the hot gaseous combustion products resulting from the combustion of the carbon in the ash along with excess air are introduced into the gasifier for providing heat energy used in the endothermic reaction. 1 fig.

Behavioural evidence of male volatile pheromones in the sex-role reversed wolf spiders Allocosa brasiliensis and Allocosa alticeps

NASA Astrophysics Data System (ADS)

Aisenberg, Anita; Baruffaldi, Luciana; González, Macarena

2010-01-01

The use of chemical signals in a sexual context is widespread in the animal kingdom. Most studies in spiders report the use of female pheromones that attract potential sexual partners. Allocosa brasiliensis and Allocosa alticeps are two burrowing wolf spiders that show sex-role reversal. Females locate male burrows and initiate courtship before males perform any detectable visual or vibratory signal. So, females of these species would be detecting chemical or mechanical cues left by males. Our objective was to explore the potential for male pheromones to play a role in mate detection in A. brasiliensis and A. alticeps. We designed two experiments. In Experiment 1, we tested the occurrence of male contact pheromones by evaluating female courtship when exposed to empty burrows constructed by males or females (control). In Experiment 2, we tested the existence of male volatile pheromones by evaluating female behaviour when exposed to artificial burrows connected to tubes containing males, females or empty tubes (control). Our results suggest the occurrence of male volatile pheromones that trigger female courtship in both Allocosa species. The sex-role reversal postulated for these wolf spiders could be driving the consequent reversal in typical pheromone-emitter and detector roles expected for spiders.

Acetylation of oil palm empty fruit bunch fiber as an adsorbent for removal of crude oil.

PubMed

Asadpour, Robabeh; Sapari, Nasiman B; Isa, Mohamed Hasnain; Kakooei, Saeid

2016-06-01

Removal of oil spillage from the environment is a global concern. Various methods, including the use of fibers as sorbents, have been developed for oil spill control. Oil palm empty fruit bunch (OPEFB) fiber is a plant biomass that may be acetylated by acetic anhydride using N-bromosuccinimide (NBS) as a catalyst; here, the extent of acetylation may be calculated in terms of weight percent gain (WPG). The modified fiber was used to remove Tapis and Arabian crude oils. The optimum time, temperature, and catalyst concentration were 4 h, 120 °C, and 3 %, respectively, and these parameters could achieve an 11.49 % increase in WPG. The optimized parameters improved the adsorption capacity of OPEFB fibers for crude oil removal. The acetylated OPEFB fibers were characterized by using Fourier transform infrared spectroscopy and field emission scanning electron microscopy to observe the functional groups available and morphology. Kinetic and isotherm studies were conducted using different contact times and oil/water ratios. The rate of oil sorption onto the OPEFB fibers can be adequately described by the pseudo-second-order equation. Adsorption studies revealed that adsorption of crude oil on treated OPEFB fiber could be best described by the Langmuir isotherm model.

Formation of hollow atoms above a surface

NASA Astrophysics Data System (ADS)

Briand, Jean Pierre; Phaneuf, Ronald; Terracol, Stephane; Xie, Zuqi

2012-06-01

Slow highly stripped ions approaching or penetrating surfaces are known to capture electrons into outer shells of the ions, leaving the innermost shells empty, and forming hollow atoms. Electron capture occurs above and below the surfaces. The existence of hollow atoms below surfaces e.g. Ar atoms whose K and L shells are empty, with all electrons lying in the M and N shells, was demonstrated in 1990 [1]. At nm above surfaces, the excited ions may not have enough time to decay before hitting the surfaces, and the formation of hollow atoms above surfaces has even been questioned [2]. To observe it, one must increase the time above the surface by decelerating the ions. We have for the first time decelerated O^7+ ions to energies as low as 1 eV/q, below the minimum energy gained by the ions due to the acceleration by their image charge. As expected, no ion backscattering (trampoline effect) above dielectric (Ge) was observed and at the lowest ion kinetic energies, most of the observed x-rays were found to be emitted by the ions after surface contact. [4pt] [1] J. P. Briand et al., Phys.Rev.Lett. 65(1990)159.[0pt] [2] J.P. Briand, AIP Conference Proceedings 215 (1990) 513.

Modeling flame structure in wildland fires using the one-dimensional turbulence model

Treesearch

David O. Lignell; Elizabeth I. Monson; Mark A. Finney

2010-01-01

The mechanism of flame propagation in wildland fire fuel beds is of critical importance for understanding and quantifying fire spread rates. Recent observations and experiments have indicated the dominance of flame propagation by direct contact between flames and unburnt fuel, as opposed to propagation via radiative heating alone. It is postulated that effects of...

Ubiquitous Learning (U-Learning) Awareness among the Tuticorin District B.Ed., Trainees

ERIC Educational Resources Information Center

Thiyagu, K.

2011-01-01

The rapid development of information and communication technologies during the past two decades has had many points of contact with education and training. The use of technology in colleges and schools is not new. Teacher training often includes computer-assisted learning along with other multimedia presentation techniques. The power of ICT over…

Effect of solid-meal caloric content on gastric emptying kinetics of solids and liquids.

PubMed

Urbain, J L; Siegel, J A; Mortelmans, L; van Cutsem, E; van den Maegdenbergh, V; de Roo, M

1989-08-01

In this study, we have evaluated the effect of the caloric content of a physiological test meal on the gastric emptying kinetics of solids and liquids. 22 healthy male volunteers were studied in two groups matched for age. After an overnight fast, each volunteer underwent the same test procedure; in the first group (G I), 10 volunteers received a meal consisting of bread, 111In-DTPA water and 1 scrambled egg labeled with 99mTc-labelled sulphur colloid; in the second group (G II) 12 volunteers were given the same meal but with 2 labeled eggs in order to increase the caloric content of the solid phase meal. Simultaneous anterior and posterior images were recorded using a dual-headed gamma camera. Solid and liquid geometric mean data were analyzed to determine the lag phase, the emptying rate and the half-emptying time for both solids and liquids. Solid and liquid gastric half-emptying times were significantly prolonged in G II compared to G I volunteers. For the solid phased, the delay was accounted for by a longer lag phase and a decrease in the equilibrium emptying rate. The emptying rate of the liquid phase was significantly decreased in G II compared to G I. Within each group, no statistically significant difference was observed between solid and liquid emptying rates. We conclude that the caloric content of the solid portion of a meal not only alters the emptying of the solid phase but also affects the emptying of the liquid component of the meal.

Gastric emptying after artificial ulceration in rats: differences due to the site of the ulcer and the effects of prokinetic drugs.

PubMed

Uchida, Masayuki; Kobayashi, Orie; Shimizu, Kimiko

2017-01-01

Background This study aimed to evaluate the effects of the position of an acetic acid-induced gastric ulcer and the effects of prokinetic drugs on gastric emptying. Materials and Methods Male Sprague-Dawley rats were used in this study. Acetic acid ulcers were induced either in the region between the fundus and pylorus on the anterior wall of the stomach or in the glandular region on the greater curvature of the stomach to determine whether there were regional differences in the effect of the ulcers. Gastric emptying was evaluated with a breath test using [1- 13 C] acetic acid. In addition, the effects of the prokinetic drugs, metoclopramide and mosapride, on gastric emptying were also evaluated. Results Acetic acid induced ulcers in the region between the fundus and pylorus on the anterior wall of the stomach significantly delayed gastric emptying as compared with control rats, but not the acetic acid induced ulcers in the glandular region on the greater curvature of the stomach. Metoclopramide and mosapride did not improve the delayed gastric emptying even at doses that enhanced gastric emptying in normal rats. Conclusion These findings show that gastric emptying is influenced by the position of the ulcer and the region between the fundus and pylorus on the anterior wall plays an important role in gastric emptying. Moreover, it was found that metoclopramide and mosapride do not improve the delayed gastric emptying caused by acetic acid ulcers induced on the anterior wall in the region between the fundus and pylorus.

Gastric emptying after artificial ulceration in rats: differences due to the site of the ulcer and the effects of prokinetic drugs

PubMed Central

Uchida, Masayuki; Kobayashi, Orie; Shimizu, Kimiko

2017-01-01

Abstract Background This study aimed to evaluate the effects of the position of an acetic acid-induced gastric ulcer and the effects of prokinetic drugs on gastric emptying. Materials and Methods Male Sprague-Dawley rats were used in this study. Acetic acid ulcers were induced either in the region between the fundus and pylorus on the anterior wall of the stomach or in the glandular region on the greater curvature of the stomach to determine whether there were regional differences in the effect of the ulcers. Gastric emptying was evaluated with a breath test using [1-13C] acetic acid. In addition, the effects of the prokinetic drugs, metoclopramide and mosapride, on gastric emptying were also evaluated. Results Acetic acid induced ulcers in the region between the fundus and pylorus on the anterior wall of the stomach significantly delayed gastric emptying as compared with control rats, but not the acetic acid induced ulcers in the glandular region on the greater curvature of the stomach. Metoclopramide and mosapride did not improve the delayed gastric emptying even at doses that enhanced gastric emptying in normal rats. Conclusion These findings show that gastric emptying is influenced by the position of the ulcer and the region between the fundus and pylorus on the anterior wall plays an important role in gastric emptying. Moreover, it was found that metoclopramide and mosapride do not improve the delayed gastric emptying caused by acetic acid ulcers induced on the anterior wall in the region between the fundus and pylorus. PMID:28652516

Novel method to assess gastric emptying in humans: the Pellet Gastric Emptying Test

NASA Technical Reports Server (NTRS)

Choe, S. Y.; Neudeck, B. L.; Welage, L. S.; Amidon, G. E.; Barnett, J. L.; Amidon, G. L.

2001-01-01

To further validate the Pellet Gastric Emptying Test (PGET) as a marker of gastric emptying, a randomized, four-way crossover study was conducted with 12 healthy subjects. The study consisted of oral co-administration of enteric coated caffeine (CAFF) and acetaminophen (APAP) pellets in four treatment phases: Same Size (100 kcal), Fasted, Small Liquid Meal (100 kcal), and Standard Meal (847 kcal). The time of first appearance of measurable drug marker in plasma, t(initial), was taken as the emptying time for the markers. Co-administration of same size enteric coated pellets of CAFF and APAP (0.7 mm in diameter) revealed no statistically significant differences in t(initial) values indicating that emptying was dependent only on size and not on chemical make-up of the pellets. Co-administration of different size pellets indicated that the smaller 0.7-mm diameter (CAFF) pellets were emptied and absorbed significantly earlier than the larger 3.6-mm diameter (APAP) pellets with both the Small Liquid Meal (by 35 min) and the Standard Meal (by 33 min) (P<0.05). The differences in emptying of the pellets were not significant in the Fasted Phase. The results suggest that the pellet gastric emptying test could prove useful in monitoring changes in transit times in the fasted and fed states and their impact on drug absorption.

Calories and gastric emptying: a regulatory capacity with implications for feeding.

PubMed

McHugh, P R; Moran, T H

1979-05-01

Gastric emptying in four unanesthetized male Macaca mulatta was studied with the serial test meal method of Hunt and Spurrell. Liquid meals were infused into the stomach through a chronic indwelling Silastic cannula. Saline meals empty rapidly and exponentially. Doubling the volume of saline from 150 to 300 ml increased the emptying rate so that the half-life remained unchanged (15 min). The 150-ml glucose meals (0.05, 0.125, and 0.25 g/ml) emptied more slowly than saline, progressively more slowly with increasing concentrations (0.05--1.8, 0.125--0.78, and 0.25--0.37 ml/min) and linearly through most of their course. Doubling the volume of 0.125 g/ml-glucose meal did not change the rate of emptying. Converting grams of glucose to their caloric content, the emptying rate in kcal/min becomes constant (approx 0.4 kcal/min) in this range of concentrations. Isocaloric casein hydrolysate and medium-chain triglyceride oil meals at 0.5 kcal/ml empty at the same rate as glucose. The precision of this regulation is sufficient to give it a role in preabsorptive satiety and the control of caloric intake.

Spatial games with cyclic interactions: the response of empty sites

NASA Astrophysics Data System (ADS)

Brown, Bart; Pleimling, Michel

2015-03-01

Predator-prey models of the May-Leonard family employ empty sites in a spatial setting as an intermediate step in the reproduction process. This requirement makes the number and arrangement of empty sites important to the formation of space-time patterns. We study the density of empty sites in a stochastic predator-prey model in which the species compete in a cyclic way in two dimensions. In some cases systems of this type quickly form domains of neutral species after which all predation, and therefore, reproduction occur near the interface of competing domains. Using Monte Carlo simulations we investigate the relationship of this density of empty sites to the time-dependent domain length. We further explore the dynamics by introducing perturbations to the interaction rates of the system after which we measure the perturbed density, i.e. the response of empty sites, as the system relaxes. A dynamical scaling behavior is observed in the response of empty sites. This work is supported by the US National Science Foundation through Grant DMR-1205309.

Aldioxa improves delayed gastric emptying and impaired gastric compliance, pathophysiologic mechanisms of functional dyspepsia

PubMed Central

Asano, Teita; Aida, Shuji; Suemasu, Shintaro; Tahara, Kayoko; Tanaka, Ken-ichiro; Mizushima, Tohru

2015-01-01

Delayed gastric emptying and impaired gastric accommodation (decreased gastric compliance) play important roles in functional dyspepsia (FD). Here we screen for a clinically used drug with an ability to improve delayed gastric emptying in rats. Oral administration of aldioxa (dihydroxyaluminum allantoinate) partially improved clonidine- or restraint stress-induced delayed gastric emptying. Administration of allantoin, but not aluminium hydroxide, restored the gastric emptying. Both aldioxa and allantoin inhibited clonidine binding to the α-2 adrenergic receptor, suggesting that antagonistic activity of the allantoin moiety of aldioxa on this receptor is involved in the restoration of gastric emptying activity. Aldioxa or aluminium hydroxide but not allantoin restored gastric compliance with restraint stress, suggesting that aluminium hydroxide moiety is involved in this restoration. We propose that aldioxa is a candidate drug for FD, because its safety in humans has already been confirmed and its ameliorating effect on both of delayed gastric emptying and impaired gastric compliance are confirmed here. PMID:26620883

How often do fishes "run on empty"?

USGS Publications Warehouse

Arrington, D.A.; Winemiller, K.O.; Loftus, W.F.; Akin, S.

2002-01-01

We used a large data set of African, Neotropical, and North American fishes to examine the frequency with which fishes have empty stomachs (nspecies = 254; nindividuals = 36875). Mean percentage of empty stomachs was low across all fishes (16.2 ?? 1.2%) but varied from 0% to 79.4% among individual species. Nocturnal fishes had empty stomachs more frequently than diurnal fishes. Trophic classification was strongly associated with the percentage of empty stomachs, a pattern also revealed from an intraspecific analysis. Fishes appear to adjust their feeding intervals relative to the energy density, conversion efficiency, and particle size of their food. Piscivorous fishes seem to be the only trophic group that regularly experience long periods of empty stomachs, with species that consume prey whole and those that provide extended parental care having the highest proportions of empty stomachs. Activity patterns and life histories of some piscivorous species probably have evolved in partial response to energetic benefits of large, energy-rich food resources.

Acute effect of indoor exposure to paint containing bis(tributyltin) oxide--Wisconsin, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-05-03

In January 1991, a woman in Wisconsin contacted her local public health department to report that she and her two children had become ill after her landlord painted the walls and ceilings of two rooms of her apartment. Reported symptoms included a burning sensation in the nose and forehead, headache, nose bleed, cough, loss of appetite, nausea, and vomiting. The woman, who was in the third trimester of pregnancy, also complained of a persistent odor from the paint and provided an empty bottle of a paint additive used for mildew control. The label indicated that this product contained 25% bis(tributyltin)more » oxide (TBTO) as its only active ingredient.« less

Effective Thermal Property Estimation of Unitary Pebble Beds Based on a CFD-DEM Coupled Method for a Fusion Blanket

NASA Astrophysics Data System (ADS)

Chen, Lei; Chen, Youhua; Huang, Kai; Liu, Songlin

2015-12-01

Lithium ceramic pebble beds have been considered in the solid blanket design for fusion reactors. To characterize the fusion solid blanket thermal performance, studies of the effective thermal properties, i.e. the effective thermal conductivity and heat transfer coefficient, of the pebble beds are necessary. In this paper, a 3D computational fluid dynamics discrete element method (CFD-DEM) coupled numerical model was proposed to simulate heat transfer and thereby estimate the effective thermal properties. The DEM was applied to produce a geometric topology of a prototypical blanket pebble bed by directly simulating the contact state of each individual particle using basic interaction laws. Based on this geometric topology, a CFD model was built to analyze the temperature distribution and obtain the effective thermal properties. The current numerical model was shown to be in good agreement with the existing experimental data for effective thermal conductivity available in the literature. supported by National Special Project for Magnetic Confined Nuclear Fusion Energy of China (Nos. 2013GB108004, 2015GB108002, 2014GB122000 and 2014GB119000), and National Natural Science Foundation of China (No. 11175207)

The effects of cholelithiasis and cholecystectomy on gastric emptying.

PubMed

Köksoy, F N; Bulut, T; Köse, H; Soybir, G; Yalçin, O; Aker, Y

In this clinical study, four groups, each consisting of 12 patients are established to determine how gastric emptying is influenced in cholelithiasis with accompanied flatulent dyspepsia and the relationship of symptoms and gastric emptying after cholecystectomy. 1. group: healthy people, 2. group: patients with dyspeptic cholelithiasis, 3. group: patients who have no dyspepsia after cholecystectomy, 4. group: patients whose dyspepsia is continued after cholecystectomy. Groups are compared according to solid phase gastric emptying scintigraphies performed with Tc 99m sulfur colloid bound with scrambled eggs. Gastric emptying delayed in second (p < 0.001) and fourth (p < 0.005) groups postprandially and not differed in the third group (p > 0.005). These results demonstrate that dyspepsia, in cholelithiasis and persisting after cholecystectomy have a close relation with delay in gastric emptying.

Effects of cholelithiasis and cholecystectomy on gastric emptying.

PubMed

Köksoy, F N; Bulut, T; Köse, H; Soybir, G; Yalçin, O; Aker, Y

1994-06-01

In this prospective, clinical study, four groups, each consisting of 12 patients were established to determine how gastric emptying is influenced in cholelithiasis with accompanied flatulent dyspepsia and the relationship of symptoms and gastric emptying after cholecystectomy: group 1--healthy people; group 2--patients with dyspeptic cholelithiasis; group 3--patients with no dyspepsia after cholecystectomy; group 4--patients with dyspepsia after cholecystectomy. Groups are compared according to solid phase gastric emptying scintigraphies performed with Tc 99m sulphur colloid bound with scrambled eggs. Gastric emptying delayed in groups 2 (P < 0.001) and 4 (P < 0.005) postprandially and did not differ in the group 3 (P > 0.005). These results demonstrate that dyspepsia, in cholelithiasis and persisting after cholecystectomy, has a close relation with delay in gastric emptying.

Host-seeking activity of a Tanzanian population of Anopheles arabiensis at an insecticide treated bed net.

PubMed

Parker, Josephine E A; Angarita Jaimes, Natalia C; Gleave, Katherine; Mashauri, Fabian; Abe, Mayumi; Martine, Jackline; Towers, Catherine E; Towers, David; McCall, Philip J

2017-07-04

Understanding how mosquitoes respond to long lasting insecticide treated nets (LLINs) is fundamental to sustaining the effectiveness of this essential control tool. We report on studies with a tracking system to investigate behaviour of wild anophelines at an LLIN, in an experimental hut at a rural site in Mwanza, Tanzania. Groups of adult female mosquitoes (n = 10 per replicate) reared from larvae of a local population, identified as predominantly (95%) Anopheles arabiensis, were released in the hut. An infrared video tracking system recorded flight and net contact activity over 1 h as the mosquitoes attempted to reach a supine human volunteer within a bed net (either a deltamethrin-treated LLIN or an untreated control net). A range of activities, including flight path, position in relation to the bed net and duration of net contact, were quantified and compared between treatments. The total time that female An. arabiensis spent in flight around LLINs was significantly lower than at untreated nets [F(1,10) = 9.26, p = 0.012], primarily due to a substantial reduction in the time mosquitoes spent in persistent 'bouncing' flight [F(1,10) = 18.48, p = 0.002]. Most activity occurred at the net roof but significantly less so with LLINs (56.8% of total) than untreated nets [85.0%; Χ 2 (15) = 234.69, p < 0.001]. Activity levels at the bed net directly above the host torso were significantly higher with untreated nets (74.2%) than LLINs [38.4%; Χ 2 (15) = 33.54, p = 0.004]. 'Visiting' and 'bouncing' rates were highest above the volunteer's chest in untreated nets (39.9 and 50.4%, respectively) and LLINs [29.9 and 42.4%; Χ 2 (13) = 89.91, p < 0.001; Χ 2 (9) = 45.73, p < 0.001]. Highest resting rates were above the torso in untreated nets [77%; Χ 2 (9) = 63.12, p < 0.001], but in LLINs only 33.2% of resting occurred here [Χ 2 (9) = 27.59, p = 0.001], with resting times spread between the short vertical side of the net adjacent to the volunteer's head (21.8%) and feet (16.2%). Duration of net contact by a single mosquito was estimated at 204-290 s on untreated nets and 46-82 s on LLINs. While latency to net contact was similar in both treatments, the reduction in activity over 60 min was significantly more rapid for LLINs [F(1,10) = 6.81, p = 0.026], reiterating an 'attract and kill' rather than a repellent mode of action. The study has demonstrated the potential for detailed investigations of behaviour of wild mosquito populations under field conditions. The results validate the findings of earlier laboratory studies on mosquito activity at LLINs, and reinforce the key role of multiple brief contacts at the net roof as the critical LLIN mode of action.

Potential health impacts of burning coal beds and waste banks

USGS Publications Warehouse

Finkelman, R.B.

2004-01-01

Uncontrolled release of pollutants from burning coal beds and waste banks presents potential environmental and human health hazards. On a global scale, the emissions of large volumes of greenhouse gases from burning coal beds may contribute to climate change that alters ecosystems and patterns of disease occurrence. On regional and local scales, the emissions from burning coal beds and waste banks of acidic gases, particulates, organic compounds, and trace elements can contribute to a range of respiratory and other human health problems. Although there are few published reports of health problems caused by these emissions, the potential for problems can be significant. In India, large numbers of people have been displaced from their homes because of health problems caused by emissions from burning coal beds. Volatile elements such as arsenic, fluorine, mercury, and selenium are commonly enriched in coal deposits. Burning coal beds can volatilize these elements, which then can be inhaled, or adsorbed on crops and foods, taken up by livestock or bioaccumulated in birds and fish. Some of these elements can condense on dust particles that can be inhaled or ingested. In addition, selenium, arsenic, lead, tin, bismuth, fluorine, and other elements condense where the hot gaseous emissions come in contact with ambient air, forming mats of concentrated efflorescent minerals on the surface of the ground. These mats can be leached by rainwater and washed into local water bodies providing other potential routes of exposure. Although there are little data linking burning coal beds and waste banks to known health problems, a possibly analogous situation exists in rural China where mineralized coal burned in a residential environment has caused widespread and severe health problems such as fluorosis and arseniasis. ?? 2004 Elsevier B.V. All rights reserved.

Removal of micropollutants during tertiary wastewater treatment by biofiltration: Role of nitrifiers and removal mechanisms.

PubMed

Rattier, M; Reungoat, J; Keller, J; Gernjak, W

2014-05-01

The objective of this study was to determine the extent to which a suite of organic micropollutants (MPs) can be removed by biological filtration and the role of bioavailability and ammonia oxidizing microorganisms (AOMs) in the biodegradation process. During approximately one year, laboratory-scale columns with 8 min empty bed contact time (EBCT) and packed with anthracite as filter media were used for treating a tertiary effluent spiked with a broad range of MPs at a target concentration of 2 μg L(-1). In parallel columns, aerobic biomass growth was inhibited by using either the biocide sodium azide (500 mg L(-1) NaN3) or allylthiourea (5 mg L(-1) ATU), specifically inhibiting nitrifying bacteria. Once the biomass had colonized the media, around 15% of the dissolved organic carbon (DOC) contained in the untreated tertiary effluent was removed by non-inhibited columns. The removal of several MPs increased over time indicating the relevance of biological activity for the removal of MPs, while the negative control, the NaN3 inhibited column, showed no significant removal. Out of 33 MPs, 19 were recalcitrant (<25%) to biodegradation under aerobic conditions with the others exhibiting a diverse range of removal efficiency up to 95%. Through inhibition by ATU it was shown that nitrifying bacteria were clearly having a role in the degradation of several MPs, whereas the removal of other MPs was not affected by the presence of the nitrification inhibitor. A relationship between the qualitative assessment of sorption of MPs on granular activated carbon (GAC) and their removal efficiency by biodegradation on anthracite was observed. This result suggested that the affinity of the MPs for GAC media could be a useful indicator of the bioavailability of compounds during biofiltration on anthracite. Copyright © 2014 Elsevier Ltd. All rights reserved.

Quantifying bacterial transfer from patients to staff during burns dressing and bed changes: implications for infection control.

PubMed

Bache, Sarah E; Maclean, Michelle; Gettinby, George; Anderson, John G; MacGregor, Scott J; Taggart, Ian

2013-03-01

Routine nursing activities such as dressing/bed changes increase bacterial dispersal from burns patients, potentially contaminating healthcare workers (HCW) carrying out these tasks. HCW thus become vectors for transmission of nosocomial infection between patients. The suspected relationship between %total body surface area (%TBSA) of burn and levels of bacterial release has never been fully established. Bacterial contamination of HCW was assessed by contact plate samples (n=20) from initially sterile gowns worn by the HCW during burns patient dressing/bed changes. Analysis of 24 gowns was undertaken and examined for relationships between %TBSA, time taken for activity, and contamination received by the HCW. Relationships between size of burn and levels of HCW contamination, and time taken for the dressing/bed change and levels of HCW contamination were best described by exponential models. Burn size correlated more strongly (R(2)=0.82, p<0.001) than time taken (R(2)=0.52, p<0.001), with levels of contamination received by the HCW. Contamination doubled with every 6-9% TBSA increase in burn size. Burn size was used to create a model to predict bacterial contamination received by a HCW carrying out bed/dressing changes. This may help with the creation of burn-specific guidelines on protective clothing worn by HCW caring for burns patients. Copyright © 2012 Elsevier Ltd and ISBI. All rights reserved.

Indoor Tanning Legislation: Shaping Policy and Nursing Practice.

PubMed

Driscoll, Donna W; Darcy, Jennifer

2015-01-01

Legislation exists regulating adolescents' use of tanning beds; however, the rate at which adolescents use these devices has not been reduced. The purpose of this study was to provide an analysis of indoor tanning bed legislation in the United States specifically related to legal issues and parental consent along with enforcement of current laws. The investigators collected data via review of state health department websites or telephone interviews of identified contacts for all 50 states. Findings reveal wide variation in legislation related to adolescents' access to tanning devices and enforcement of violation of legal statutes. Nurses and other health care professionals can play key roles in educating families and adolescents to the dangers from the use of tanning beds along with being role models for proper skin protective behaviors. In addition, nurses should become advocates by supporting legislative efforts that ban tanning salons for all minors, with the long-term goal of reducing skin cancer caused by ultraviolet radiation (UVR) exposure from the use of tanning salons today.

Combustor with multistage internal vortices

DOEpatents

Shang, Jer Yu; Harrington, R.E.

1987-05-01

A fluidized bed combustor is provided with a multistage arrangement of vortex generators in the freeboard area. The vortex generators are provided by nozzle means which extend into the interior of the freeboard for forming vortices within the freeboard areas to enhance the combustion of particulate material entrained in product gases ascending into the freeboard from the fluidized bed. Each of the nozzles are radially inwardly spaced from the combustor walls defining the freeboard to provide for the formation of an essentially vortex-free, vertically extending annulus about the vortices whereby the particulate material centrifuged from the vortices against the inner walls of the combustor is returned through the annulus to the fluidized bed. By adjusting the vortex pattern within the freeboard, a significant portion of the full cross-sectional area of the freeboard except for the peripheral annulus can be contacted with the turbulent vortical flow for removing the particulate material from the gaseous products and also for enhancing the combustion thereof within the freeboard. 2 figs.

Combustor with multistage internal vortices

DOEpatents

Shang, Jer Y.; Harrington, Richard E.

1989-01-01

A fluidized bed combustor is provided with a multistage arrangement of vortex generators in the freeboard area. The vortex generators are provided by nozzle means which extend into the interior of the freeboard for forming vortices within the freeboard area to enhance the combustion of particulate material entrained in product gases ascending into the freeboard from the fluidized bed. Each of the nozzles are radially inwardly spaced from the combustor walls defining the freeboard to provide for the formation of an essentially vortex-free, vertically extending annulus about the vortices whereby the particulate material centrifuged from the vortices against the inner walls of the combustor is returned through the annulus to the fluidized bed. By adjusting the vortex pattern within the freeboard, a significant portion of the full cross-sectional area of the freeboard except for the peripheral annulus can be contacted with the turbulent vortical flow for removing the particulate material from the gaseous products and also for enhancing the combustion thereof within the freeboard.

Process for gasifying carbonaceous material from a recycled condensate slurry

DOEpatents

Forney, Albert J.; Haynes, William P.

1981-01-01

Coal or other carbonaceous material is gasified by reaction with steam and oxygen in a manner to minimize the problems of effluent water stream disposal. The condensate water from the product gas is recycled to slurry the coal feed and the amount of additional water or steam added for cooling or heating is minimized and preferably kept to a level of about that required to react with the carbonaceous material in the gasification reaction. The gasification is performed in a pressurized fluidized bed with the coal fed in a water slurry and preheated or vaporized by indirect heat exchange contact with product gas and recycled steam. The carbonaceous material is conveyed in a gas-solid mixture from bottom to top of the pressurized fluidized bed gasifier with the solids removed from the product gas and recycled steam in a supported moving bed filter of the resulting carbonaceous char. Steam is condensed from the product gas and the condensate recycled to form a slurry with the feed coal carbonaceous particles.

Do calories or osmolality determine gastric emptying

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shafer, R.B.; Levine, A.S.; Marlette, J.M.

1984-01-01

Recent animal studies suggest that gastric emptying is dependent on the caloric and osmotic content of the ingested food. These studies have involved intubation with infusion of liquid meals into the stomach. Scintigraphic methods, which are non-invasive and do not alter normal physiology, are now available for precise quantitation of gastric emptying. To study the role of calories and osmolality on gastric emptying, the authors employed a standardized /sup 99m/Tc-scrambled egg meal washed with 50 cc tap water in 10 normal human volunteers. A variety of simple and complex sugars, non-absorbable complex carbohydrate (polycose), medium chain fatty acid (MCFA) andmore » gluten were dissolved in water and ingested with the test meal. Each subject acted as his own control. Coefficient of variation in control tests in each subject 12 weeks apart was 9.9%. Results showed that incremental glucose (25-66 gm) produced a linear increase in gastric emptying (T/2 control 50 +- 3, 25 gm 60 +- 3, 50 gm 79 +- 3 and 66 gm 102 +- 3 minutes). 25 gm fructose (T/2 59 +- 3 minutes) and 25 gm polycose (T/2 59 +- 3 minutes) had similar effects to glucose. 25 gm sucrose and 25 gm gluten did not significantly differ from controls. MCFA had an effect similar to 50 gm glucose - suggesting that calories are important in gastric emptying. However, 25 gm xylose markedly prolonged gastric emptying to 80 +- 5 minutes. The rank order for osmolality for substances tested MCFA = gluten < polycose < polycose < fructose < sucrose = glucose < xylose defined no relationship to gastric emptying. The authors' results suggest that neither calories nor osmolality alone determine gastric emptying. A specific food does not necessarily have the same effect on gastric emptying in different individuals.« less

Association of empty nest with depressive symptom in a Chinese elderly population: A cross-sectional study.

PubMed

Zhai, Yujia; Yi, Huaiming; Shen, Wei; Xiao, Yuanyuan; Fan, Haixiao; He, Fan; Li, Fudong; Wang, Xinyi; Shang, Xiaopeng; Lin, Junfen

2015-11-15

Empty nest has been becoming the main family pattern among old people, and influencing the traditional family providing for the aged in China. This study aimed to investigate the association of empty nest with depressive symptom in a Chinese elderly population. Our study was based on the baseline investigation of Zhejiang Major Public Health Surveillance which was conducted in 2014. The final analyzed sample consisted of 9215 participants aged no less than 60 years. Subjects completed a questionnaire including demographic characteristics, living arrangements, behavioral risk factors, health status, subjective assessments, and Patient Health Questionnaire-9 scale. More than half of the participants were empty nest elders (57.4%). The overall prevalence of depressive symptom was 10.3%, while it was higher in empty nest group than in non-empty nest group (11.6% vs. 8.6%, P<0.001). A positive association was found between empty nest and depressive symptom, the OR (95%CI) was 1.223(1.045, 1.431). After stratified by gender/age/education level/employment status, this association was just prominent in participants of male, 70 years old and above, primary school education, and retirees. No matter living with spouse or living alone, empty nesters were more likely to have depressive symptoms than non-empty nesters. Cross-sectional study could not make a causation conclusion. The social supports of participants were not been investigated in detail. Empty nest elders, especially those who are male, 70 years old and above, primary school education, and retired, are more vulnerable to depressive symptom. Copyright © 2015 Elsevier B.V. All rights reserved.

Loneliness and depression among rural empty-nest elderly adults in Liuyang, China: a cross-sectional study

PubMed Central

Wang, Guojun; Hu, Mi; Xiao, Shui-yuan; Zhou, Liang

2017-01-01

Objective To compare loneliness, depressive symptoms and major depressive episodes between empty-nest and not-empty-nest older adults in rural areas of Liuyang city, Hunan, China. Methods A cross-sectional multi-stage random cluster survey was conducted from November 2011 to April 2012 in Liuyang, China. A total of 839 rural older residents aged 60 or above completed the survey (response rate 97.6%). In line with the definition of empty nest, 25 participants who had no children were excluded from the study, while the remaining 814 elderly adults with at least one child were included for analysis. Loneliness and depressive symptoms in rural elderly parents were assessed using the short-form UCLA Loneliness Scale (ULS-6) and the Geriatric Depression Scale (GDS). Major depressive episodes were diagnosed using the Structured Clinical Interview for DSM-IV (SCID-I). Results Significant differences were found between empty-nest and not-empty-nest older adults regarding loneliness (16.19±3.90 vs. 12.87±3.02, Cohen’s d=0.97), depressive symptoms (8.50±6.26 vs. 6.92±5.19, Cohen’s d=0.28) and the prevalence of major depressive episodes (10.1% vs. 4.6%) (all p<0.05). After controlling for demographic characteristics and physical disease, the differences in loneliness, depressive symptoms and major depressive episodes remained significant. Path analysis showed that loneliness mediated the relationship between empty-nest syndrome and depressive symptoms and major depressive episodes. Conclusion Loneliness and depression are more severe among empty-nest than not-empty-nest rural elderly adults. Loneliness was a mediating variable between empty-nest syndrome and depression. PMID:28988166

Gastric emptying of solids and liquids in obesity.

PubMed

Glasbrenner, B; Pieramico, O; Brecht-Krauss, D; Baur, M; Malfertheiner, P

1993-07-01

The purpose of this study was to determine whether obese patients have different rates of solid and liquid gastric emptying compared to healthy controls. Twenty-four obese patients (7 males, 17 females) were investigated prior to dietary restriction. The patients had a weight excess above ideal weight ranging from 25% to 216% (mean weight 118.1 +/- 6.5 kg). The control group consisted of 8 healthy subjects (4 males, 4 females), within 10% of the ideal weight. The solid phase of the test meal consisted of 40 g bread, 30 g ham, 10 g margarine, and two scrambled eggs labeled with 99mTc. For the liquid phase, 200 ml orange juice was labeled with 201Tl. Three-minute counts of both tracers were taken for 106 min using a large field-of-view gamma camera. In obese patients, a significantly shortened lag phase for the emptying of solids was observed (27.0 +/- 3.3 versus 38.4 +/- 4.1 min; P < 0.05). Half-emptying time (105.9 +/- 6.7 versus 100.7 +/- 5.7 min), emptying rate (0.60 +/- 0.04 versus 0.71 +/- 0.07%/min), and total emptying of solids (49.4 +/- 3.6 versus 50.5 +/- 5.0%) were not different from controls. Obese subjects had a trend to slowed liquid emptying (half-time 82.7 +/- 4.8 versus 69.9 +/- 6.9 min; emptying rate 0.59 +/- 0.03 versus 0.65 +/- 0.03%/min; total emptying 59.8 +/- 2.9 versus 66.0 +/- 3.3%), but this was not statistically significant. There was no correlation between weight or body surface area and rate of solid or liquid gastric emptying.(ABSTRACT TRUNCATED AT 250 WORDS)

Risk factors associated with delayed gastric emptying after subtotal gastrectomy with Billroth-I anastomosis using circular stapler for early gastric cancer patients.

PubMed

Kim, Ki Han; Kim, Min Chan; Jung, Ghap Joong

2012-11-01

Gastric surgery may potentiate delayed gastric emptying. Billroth I gastroduodenostomy using a circular stapler is the most preferable reconstruction method. The purpose of this study is to analyze the risk factors associated with delayed gastric emptying after radical subtotal gastrectomy with Billroth I anastomosis using a stapler for early gastric cancer. Three hundred and seventy-eight patients who underwent circular stapled Billroth I gastroduodenostomy after subtotal gastrectomy due to early gastric cancer were analyzed retrospectively. One hundred and eighty-two patients had Billroth I anastomosis using a 25 mm diameter circular stapler, and 196 patients had anastomosis with a 28 or 29 mm diameter circular stapler. Clinicopathological features and postoperative outcomes were evaluated and compared between the two groups. Delayed gastric emptying was diagnosed by symptoms and simple abdomen X-ray with or without upper gastrointestinal series or endoscopy. Postoperative delayed gastric emptying was found in 12 (3.2%) of the 378 patients. Among all the variables, distal margin and circular stapler diameter were significantly different between the cases with delayed gastric emptying and no delayed gastric emptying. There were statistically significant differences in sex, body mass index, comorbidity, complication, and operation type according to circular stapler diameter. In both univariate and multivariate logistic regression analyses, only the stapler diameter was found to be a significant factor affecting delayed gastric emptying (P = 0.040). In this study, the circular stapler diameter was one of the most significant predictable factors of delayed gastric emptying for Billroth I gastroduodenostomy. The use of a 28 or 29 mm diameter circular stapler rather than a 25 mm diameter stapler in stapled gastroduodenostomy for early gastric cancer can reduce postoperative delayed gastric emptying associated with anastomosic stenosis or edema with relative safety.

Where are kids getting their empty calories? Stores, schools, and fast food restaurants each play an important role in empty calorie intake among US children in 2009-2010

PubMed Central

Poti, Jennifer M.; Slining, Meghan M.; Popkin, Barry M.; Kenan, W.R.

2013-01-01

Consumption of empty calories, the sum of energy from added sugar and solid fat, exceeds recommendations, but little is known about where US children obtain these empty calories. The objectives of this study were to compare children's empty calorie consumption from retail food stores, schools, and fast food restaurants; to identify food groups that were top contributors of empty calories from each location; and to determine the location providing the majority of calories for these key food groups. This cross-sectional analysis used data from 3,077 US children aged 2-18 years participating in the 2009-2010 National Health and Nutrition Examination Survey. The empty calorie content of children's intake from stores (33%), schools (32%), and fast food restaurants (35%) was not significantly different in 2009-2010. In absolute terms, stores provided the majority of empty calorie intake (436 kcal). The top contributors of added sugar and solid fat from each location were similar: sugar sweetened beverages (SSBs), grain desserts, and high-fat milk from stores; high-fat milk, grain desserts, and pizza from schools; and SSBs, dairy desserts, french fries, and pizza from fast food restaurants. Schools contributed about 20% of children's intake of high-fat milk and pizza. In conclusion, these findings support the need for continued efforts to reduce empty calorie intake among US children aimed not just at fast food restaurants, but also at stores and schools. The importance of reformed school nutrition standards was suggested, as prior to their implementation, schools resembled fast food restaurants in their contributions to empty calorie intake. PMID:24200654

Where are kids getting their empty calories? Stores, schools, and fast-food restaurants each played an important role in empty calorie intake among US children during 2009-2010.

PubMed

Poti, Jennifer M; Slining, Meghan M; Popkin, Barry M

2014-06-01

Consumption of empty calories, the sum of energy from added sugar and solid fat, exceeds recommendations, but little is known about where US children obtain these empty calories. The objectives of this study were to compare children's empty calorie consumption from retail food stores, schools, and fast-food restaurants; to identify food groups that were top contributors of empty calories from each location; and to determine the location providing the majority of calories for these key food groups. This cross-sectional analysis used data from 3,077 US children aged 2 to 18 years participating in the 2009-2010 National Health and Nutrition Examination Survey. The empty calorie content of children's intake from stores (33%), schools (32%), and fast-food restaurants (35%) was not significantly different in 2009-2010. In absolute terms, stores provided the majority of empty calorie intake (436 kcal). The top contributors of added sugar and solid fat from each location were similar: sugar-sweetened beverages, grain desserts, and high-fat milk∗ from stores; high-fat milk, grain desserts, and pizza from schools; and sugar-sweetened beverages, dairy desserts, french fries, and pizza from fast-food restaurants. Schools contributed about 20% of children's intake of high-fat milk and pizza. These findings support the need for continued efforts to reduce empty calorie intake among US children aimed not just at fast-food restaurants, but also at stores and schools. The importance of reformed school nutrition standards was suggested, as prior to implementation of these changes, schools resembled fast-food restaurants in their contributions to empty calorie intake. Copyright © 2014 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Research on strategy and optimization method of PRT empty vehicles resource allocation based on traffic demand forecast

NASA Astrophysics Data System (ADS)

Xiang, Yu; Tao, Cheng

2018-05-01

During the operation of the personal rapid transit system(PRT), the empty vehicle resources is distributed unevenly because of different passenger demand. In order to maintain the balance between supply and demand, and to meet the passenger needs of the ride, PRT empty vehicle resource allocation model is constructed based on the future demand forecasted by historical demand in this paper. The improved genetic algorithm is implied in distribution of the empty vehicle which can reduce the customers waiting time and improve the operation efficiency of the PRT system so that all passengers can take the PRT vehicles in the shortest time. The experimental result shows that the improved genetic algorithm can allocate the empty vehicle from the system level optimally, and realize the distribution of the empty vehicle resources reasonably in the system.

Analysis of empty ATLAS pilot jobs

NASA Astrophysics Data System (ADS)

Love, P. A.; Alef, M.; Dal Pra, S.; Di Girolamo, A.; Forti, A.; Templon, J.; Vamvakopoulos, E.; ATLAS Collaboration

2017-10-01

In this analysis we quantify the wallclock time used by short empty pilot jobs on a number of WLCG compute resources. Pilot factory logs and site batch logs are used to provide independent accounts of the usage. Results show a wide variation of wallclock time used by short jobs depending on the site and queue, and changing with time. For a reference dataset of all jobs in August 2016, the fraction of wallclock time used by empty jobs per studied site ranged from 0.1% to 0.8%. Aside from the wall time used by empty pilots, we also looked at how many pilots were empty as a fraction of all pilots sent. Binning the August dataset into days, empty fractions between 2% and 90% were observed. The higher fractions correlate well with periods of few actual payloads being sent to the site.

Involvement of endogenous opiates in regulation of gastric emptying of fat test meals in mice

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fioramonti, J.; Fargeas, M.J.; Bueno, L.

1988-08-01

The role of endogenous opioids and cholecystokinin (CCK) in gastric emptying was investigated in mice killed 30 min after gavage with /sup 51/Cr-radiolabeled liquid meals. The meals consisted of 0.5 ml of milk or one of five synthetic meals containing arabic gum, glucose and/or arachis oil and/or casein. Naloxone (0.1 mg/kg sc) significantly (P less than 0.01) accelerated gastric emptying of milk and meals containing fat but did not modify gastric emptying of nonfat meals. The CCK antagonist asperlicin (0.1 mg/kg ip) increased by 25% gastric emptying of milk. The gastric emptying of meals containing glucose and casein but notmore » fat was reduced after administration of the COOH-terminal octapeptide of cholecystokinin (CCK-8, 4 micrograms/kg ip). This decrease was antagonized by both asperlicin (10 mg/kg ip) and naloxone (0.1 mg/kg sc). Intracerebroventricular (icv) administration of an opiate antagonist that poorly crosses the blood-brain barrier, methyl levallorphan (10 micrograms/kg), did not modify gastric emptying of milk but accelerated it when peripherally administered (0.1 mg/kg sc). Similarly, asperlicin (icv) administered at a dose of 1 mg/kg did not affect milk emptying. These results indicate that endogenous opiates are involved at peripheral levels in the regulation of gastric emptying of fat meals only and that such regulation involves release of CCK.« less

Characterization of complete particles (VSV-G/SIN-GFP) and empty particles (VSV-G/EMPTY) in human immunodeficiency virus type 1-based lentiviral products for gene therapy: potential applications for improvement of product quality and safety.

PubMed

Zhao, Yuan; Keating, Kenneth; Dolman, Carl; Thorpe, Robin

2008-05-01

Lentiviral vectors persist in the host and are therefore ideally suited for long-term gene therapy. To advance the use of lentiviral vectors in humans, improvement of their production, purification, and characterization has become increasingly important and challenging. In addition to cellular contaminants derived from packaging cells, empty particles without therapeutic function are the major impurities that compromise product safety and efficacy. Removal of empty particles is difficult because of their innate similarity in particle size and protein composition to the complete particles. We propose that comparison of the properties of lentiviral products with those of purposely expressed empty particles may reveal potential differences between empty and complete particles. For this, three forms of recombinant lentiviral samples, that is, recombinant vesicular stomatitis virus glycoprotein (VSV-G) proteins, empty particles (VSV-G/Empty), and complete particles (VSV-G/SIN-GFP) carrying viral RNA, were purified by size-exclusion chromatography (SEC). The SEC-purified samples were further analyzed by immunoblotting with six antibodies to examine viral and cellular proteins associated with the particles. This study has demonstrated, for the first time, important differences between VSV-G/Empty particles and complete VSV-G/SIN-GFP particles. Differences include the processing of Gag protein and the inclusion of cellular proteins in the particles. Our findings support the development of improved production, purification, and characterization methods for lentiviral products.

Automatic high throughput empty ISO container verification

NASA Astrophysics Data System (ADS)

Chalmers, Alex

2007-04-01

Encouraging results are presented for the automatic analysis of radiographic images of a continuous stream of ISO containers to confirm they are truly empty. A series of image processing algorithms are described that process real-time data acquired during the actual inspection of each container and assigns each to one of the classes "empty", "not empty" or "suspect threat". This research is one step towards achieving fully automated analysis of cargo containers.

Comparative study of gastric emptying and nutritional status after pylorus-preserving vs. subtotal stomach-preserving pancreaticoduodenectomy.

PubMed

Hiyoshi, Masahide; Chijiiwa, Kazuo; Ohuchida, Jiro; Imamura, Naoya; Nagano, Motoaki

2012-06-01

Delayed gastric emptying (DGE) is a specific, worrisome complication after pancreaticoduodenectomy (PPPD), whereas subtotal stomach-preserving pancreaticoduodenectomy (SSPPD) that excises the pylorus ring seems to be effective in reducing DGE. This study compared gastric emptying and nutritional status between PPPD and SSPPD over 1 year. From June 2003 to December 2007, 41 patients (PPPD: 33, SSPPD: 8) were enrolled in this study to evaluate differences in gastric emptying and nutritional status at 1, 3, 6, 9 and 12 months after pancreaticoduodenectomy. Gastric emptying was evaluated by 13C-acetate breath test. Nutritional status (body weight, serum levels of total protein, albumin and total cholesterol) was similarly assessed. At 1 month, gastric emptying evaluated at T1/2 (half-emptying time) was significantly prolonged in the PPPD but not in the SSPPD compared to the preoperative level. Thereafter, T1/2 was decreased and showed function significantly better preserved at 3, 6 and 12 months after PPPD than after SSPPD. Body weight recovery was significantly better at 6 and 12 months after PPPD than after SSPPD. Other nutritional parameters were better preserved in the PPPD during 1-year follow-up. PPPD seems to be a more suitable surgical procedure than SSPPD in regard to gastric emptying and nutritional status.

Injuries, envenomations and stings from exotic pets

PubMed Central

Warwick, Clifford; Steedman, Catrina

2012-01-01

A variety of exotic vertebrate and invertebrate species are kept as ‘pets’ including fishes, amphibians (for example, frogs and toads), reptiles (turtles, crocodiles, lizards and snakes), birds, mammals (for example, primates, civets, and lions), and invertebrates (for example spiders, scorpions, and centipedes), and ownership of some of these animals is rising. Data for 2009–2011 suggest that the number of homes with reptiles rose by approximately 12.5%. Recent surveys, including only some of these animals, indicated that they might be present in around 18.6% of homes (equal to approximately 42 million animals of which around 40 million are indoor or outdoor fish). Many exotic ‘pets’ are capable of causing injury or poisoning to their keepers and some contacts prove fatal. We examined NHS Health Episode Statistics for England using selected formal categories for hospital admissions and bed days for 2004–2010 using the following categories of injury, envenomation or sting; bitten or struck by crocodile or alligator; bitten or crushed by other reptiles: contact with venomous snakes and lizards; contact with scorpions. Between 2004 and 2010 these data conservatively show a total of 760 full consultation episodes, 709 admissions and 2,121 hospital bed days were associated with injuries probably from exotic pets. Injuries, envenomations and stings from exotic pets constitute a small but important component of emerging medical problems. Greater awareness of relevant injuries and medical sequelae from exotic pet keeping may help medics formulate their clinical assessment and advice to patients. PMID:22843648

Injuries, envenomations and stings from exotic pets.

PubMed

Warwick, Clifford; Steedman, Catrina

2012-07-01

A variety of exotic vertebrate and invertebrate species are kept as 'pets' including fishes, amphibians (for example, frogs and toads), reptiles (turtles, crocodiles, lizards and snakes), birds, mammals (for example, primates, civets, and lions), and invertebrates (for example spiders, scorpions, and centipedes), and ownership of some of these animals is rising. Data for 2009-2011 suggest that the number of homes with reptiles rose by approximately 12.5%. Recent surveys, including only some of these animals, indicated that they might be present in around 18.6% of homes (equal to approximately 42 million animals of which around 40 million are indoor or outdoor fish). Many exotic 'pets' are capable of causing injury or poisoning to their keepers and some contacts prove fatal. We examined NHS Health Episode Statistics for England using selected formal categories for hospital admissions and bed days for 2004-2010 using the following categories of injury, envenomation or sting; bitten or struck by crocodile or alligator; bitten or crushed by other reptiles: contact with venomous snakes and lizards; contact with scorpions. Between 2004 and 2010 these data conservatively show a total of 760 full consultation episodes, 709 admissions and 2,121 hospital bed days were associated with injuries probably from exotic pets. Injuries, envenomations and stings from exotic pets constitute a small but important component of emerging medical problems. Greater awareness of relevant injuries and medical sequelae from exotic pet keeping may help medics formulate their clinical assessment and advice to patients.

Active Flexural-Slip Faulting: Controls Exerted by Stratigraphy, Geometry, and Fold Kinematics

NASA Astrophysics Data System (ADS)

Li, Tao; Chen, Jie; Thompson Jobe, Jessica A.; Burbank, Douglas W.

2017-10-01

Flexural slip plays an important role in accommodating fold growth, and its topographic expression, flexural-slip fault (FSF) scarps, may be one of the most commonly occurring secondary structures in areas dominated by active thrusts and folds. Where FSF scarps are present and what factors control their occurrence, however, are typically poorly known. Through an investigation of clearly expressed FSF scarps, well-preserved fluvial terraces, and well-exposed bedrock at eight sites in the Pamir-Tian Shan convergent zone and Kuche fold belt, NW China, we summarize the most favorable conditions for active flexural-slip faulting. Our study yields six key results. First, flexural slip operates commonly in well-layered beds, although uncommonly can occur in massive, poorly layered beds as well. Second, in well-layered beds, the slip surface is commonly located either (a) close to the contact of competent and incompetent beds or (b) within thin incompetent beds. Third, FSF scarps are always found overlying steep beds with dips of 30-100°. Fourth, slip surfaces are typically spaced between 10 and 440 m but can reach up to 600 m. Fifth, FSF scarps at most sites can be observed far away from the hinge-migrated fold scarps, suggesting that compared to hinge migration, limb rotation is generally required to accumulate flexural slip and produce associated topographic scarps. Finally, a higher regional convergent rate seems to facilitate the creation of FSF scarps more often than lower rates, whereas well-preserved, old terraces capped by thin deposits are more likely to record FSF scarps than unevenly preserved, young terraces with thick sedimentary caps.

Apparatus and method for feeding coal into a coal gasifier

DOEpatents

Bissett, Larry A.; Friggens, Gary R.; McGee, James P.

1979-01-01

This invention is directed to a system for feeding coal into a gasifier operating at high pressures. A coal-water slurry is pumped to the desired pressure and then the coal is "dried" prior to feeding the coal into the gasifier by contacting the slurry with superheated steam in an entrained bed dryer for vaporizing the water in the slurry.

Structure of diffusion flames from a vertical burner

Treesearch

Mark A. Finney; Dan Jimenez; Jack D. Cohen; Isaac C. Grenfell; Cyle Wold

2010-01-01

Non-steady and turbulent flames are commonly observed to produce flame contacts with adjacent fuels during fire spread in a wide range of fuel bed depths. A stationary gas-fired burner (flame wall) was developed to begin study of flame edge variability along an analagous vertical fuel source. This flame wall is surrogate for a combustion interface at the edge of a deep...

Anthrax (Lecture Aids) - USSR .

DTIC Science & Technology

1961-08-14

cutting up its carcass and intestines are disinfected or, if they are not valuable, are burned. In the quarters of infected persons, bed linen and...objects which could have come into contact with discharges by the patient are disinfected . Industrial anthrax infections. Infection occurs in...spores. As we have already mentioned, spores’occur on the surface of wool and hair. YThis facilitates, disinfection ; excellent results are

Concomitant Alterations of Desmosomes, Adhesiveness, and Diffusion through Gap Junction Channels in a Rat Ovarian Transformation Model System

DTIC Science & Technology

1993-01-01

while using a sterile glass slide, held parallel to the monolayer, as a MATERIALS AND METHODS straight edge. Cultures were photographed using phase...contrastmicrosoyo tonoa~r movng ofi I spheria mi rocr rie bed ntI h CEILL CELIL CONTACT AND DIFFU SION 23 and cytokeratin 8 antibodies (refer to Figs. 4a

Why does the Conductivity of a Nickel Catalyst Increase during Sulfidation? An Exemplary Study Using an In Operando Sensor Device

PubMed Central

Fremerey, Peter; Jess, Andreas; Moos, Ralf

2015-01-01

In order to study the sulfidation of a catalyst fixed bed, an in operando single pellet sensor was designed. A catalyst pellet from the fixed bed was electrically contacted and its electrical response was correlated with the catalyst behavior. For the sulfidation tests, a nickel catalyst was used and was sulfidized with H2S. This catalyst had a very low conductivity in the reduced state. During sulfidation, the conductivity of the catalyst increased by decades. A reaction from nickel to nickel sulfide occurred. This conductivity increase by decades during sulfidation had not been expected since both nickel and nickel sulfides behave metallic. Only by assuming a percolation phenomenon that originates from a volume increase of the nickel contacts when reacting to nickel sulfides, this effect can be explained. This assumption was supported by sulfidation tests with differently nickel loaded catalysts and it was quantitatively estimated by a general effective media theory. The single pellet sensor device for in operando investigation of sulfidation can be considered as a valuable tool to get further insights into catalysts under reaction conditions. PMID:26512669

Associations between living arrangements and health-related quality of life of urban elderly people: a study from China.

PubMed

Sun, Xiaojie; Lucas, Henry; Meng, Qingyue; Zhang, Yaoguang

2011-04-01

This study aimed to compare health-related quality of life (HRQOL) for elderly men and women in three mutually exclusive living arrangements: living alone, living only with spouse, and non-empty-nesters. It also examined whether such living arrangements and other factors relating to social interaction have an independent influence on HRQOL after controlling for other variables. The data were drawn from China's 4th National Household Health Survey (NHHS) conducted in 2008. The final sample included 9,711 urban elderly people of 60 years and above. The EQ-5D inventory was used to measure health-related quality of life. The proportions of non-empty-nested men and women both changed following a 'U'-shaped curve with the increasing age. Controlling for other variables not including social interaction indicators, "living alone" was a significant predictor of reporting problems on Mobility, Pain/Discomfort and Anxiety/Depression. After introducing social interaction indicators, urban older adults 'having close contact with neighbors every week' had lower odds of problems on all five EQ-5D indicators, those 'having close contact with friends and relatives' had lower odds of problems on Mobility, Pain/Discomfort and Anxiety/Depression, and those 'taking part in social activities every week' had lower odds of problems on all dimensions but Anxiety/Depression. In addition, after introducing social interaction indicators, the odds of reported problems on the three dimensions increased obviously. This study suggests that the most vulnerable urban older adults are those who live entirely on their own. Frequent social interaction may buffer the negative effect of living alone on HRQOL of older adults. Policies that attempt to build harmonious neighborhoods, extend older adults' social network and encourage them to take part in social activities should be considered by the policy-makers in the future.

Alkylation of organic aromatic compounds

DOEpatents

Smith, L.A. Jr.

1989-07-18

Aromatic compounds are alkylated in a catalytic distillation, wherein the catalyst structure also serves as a distillation component by contacting the aromatic compound with a C[sub 2] to C[sub 10] olefin in the catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 80 C to 500 C, using as the catalyst a mole sieve characterized as acidic or an acidic cation exchange resin. For example, ethyl benzene is produced by feeding ethylene below the catalyst bed while benzene is conveniently added through the reflux in molar excess to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene in the bottoms. 1 fig.

Alkylation of organic aromatic compounds

DOEpatents

Smith, Jr., Lawrence A.; Arganbright, Robert P.; Hearn, Dennis

1994-01-01

Aromatic compounds are alkylated in a catalytic distillation, wherein the catalyst structure also serves as a distillation component by contacting the aromatic compound with a C.sub.2 to C.sub.10 olefin in the catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 80.degree. C. to 500.degree. C., using as the catalyst a mole sieve characterized as acidic or an acidic cation exchange resin. For example, ethyl benzene is produced by feeding ethylene below the catalyst bed while benzene is conveniently added through the reflux in molar excess to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene in the bottoms.

Alkylation of organic aromatic compounds

DOEpatents

Smith, Jr., Lawrence A.

1989-01-01

Aromatic compounds are alkylated in a catalytic distillation, wherein the catalyst structure also serves as a distillation component by contacting the aromatic compound with a C.sub.2 to C.sub.10 olefin in the catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 80.degree. C. to 500.degree. C., using as the catalyst a mole sieve characterized as acidic or an acidic cation exchange resin. For example, ethyl benzene is produced by feeding ethylene below the catalyst bed while benzene is conveniently added through the reflux in molar excess to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene in the bottoms.

Alkylation of organic aromatic compounds

DOEpatents

Smith, L.A. Jr.; Arganbright, R.P.; Hearn, D.

1994-06-14

Aromatic compounds are alkylated in a catalytic distillation, wherein the catalyst structure also serves as a distillation component by contacting the aromatic compound with a C[sub 2] to C[sub 10] olefin in the catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 80 C to 500 C, using as the catalyst a molecular sieve characterized as acidic or an acidic cation exchange resin. For example, ethyl benzene is produced by feeding ethylene below the catalyst bed while benzene is conveniently added through the reflux in molar excess to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene in the bottoms. 1 fig.

Full-Scale Experimental Investigation to Quantify Building Component Ignition Vulnerability from Mulch Beds Attacked by Firebrand Showers.

PubMed

Manzello, Samuel L; Suzuki, Sayaka; Nii, Daisaku

2017-03-01

Structure ignition by wind-driven firebrand showers is an important fire spread mechanism in large outdoor fires. Experiments were conducted with three common mulch types (shredded hardwood mulch, Japanese Cypress wood chips, and pine bark nuggets) placed adjacent to realistic-scale reentrant corners. In the first series of experiments, mulch beds were placed adjacent to a re-entrant corner constructed with wood studs and lined with oriented strand board (OSB) as the sheathing. The premise behind conducting experiments with no siding treatments applied was predicated on the notion that bare OSB mulch contact would be a worst-case scenario, and therefore, a wall assembly in the most vulnerable state to mulch ignition. In the second series of experiments, vinyl siding was applied to the re-entrant corner assemblies (wood studs/OSB/moisture barrier/vinyl siding), and the influence of vertical separation distance (102 mm or 203 mm) on wall ignition from adjacent mulch beds was determined. The vertical separation distance was maintained by applying gypsum board to the base of the re-entrant corner. The siding itself did not influence the ignition process for the mulch beds, as the mulch beds were the first to ignite from the firebrand showers. In all experiments, it was observed that firebrands produced smoldering ignition in the mulch beds, this transitioned to flaming ignition, and the re-entrant corner assembly was exposed to the flaming mulch beds. With no siding treatments applied, the flaming mulch beds ignited the re-entrant corner, and ignition was observed to propagate to the back side of re-entrant corner assembly under all wind speeds (6 m/s to 8 m/s). With respect to the re-entrant corners fitted with vinyl siding, the mulch type, vertical separation distance, and wind speed were important parameters as to whether flaming ignition was observed to propagate to the back-side of a reentrant corner assembly. Mulches clearly pose an ignition hazard to structures in large outdoor fires.

Common and Distinct Capsid and Surface Protein Requirements for Secretion of Complete and Genome-free Hepatitis B Virions.

PubMed

Ning, Xiaojun; Luckenbaugh, Laurie; Liu, Kuancheng; Bruss, Volker; Sureau, Camille; Hu, Jianming

2018-05-09

During the morphogenesis of hepatitis B virus (HBV), an enveloped virus, two types of virions are secreted: (1) a minor population of complete virions containing a mature nucleocapsid with the characteristic, partially double-stranded, relaxed circular DNA genome and (2) a major population containing an empty capsid with no DNA or RNA (empty virions). Secretion of both types of virions requires interactions between the HBV capsid or core protein (HBc) and the viral surface or envelope proteins. We have studied the requirements from both HBc and envelope proteins for empty virion secretion, in comparison with those for secretion of complete virions. Substitutions within the N-terminal domain of HBc that block secretion of DNA-containing virions reduced but did not prevent secretion of empty virions. The HBc C-terminal domain was not essential for empty virion secretion. Among the three viral envelope proteins, the smallest, S, alone was sufficient for empty virion secretion at a basal level. The largest protein, L, essential for complete virion secretion, was not required for, but could stimulate empty virion secretion. Also, substitutions in L that eliminate secretion of complete virions reduced but did not eliminate empty virion secretion. S mutations that block secretion of the hepatitis D virus (HDV), an HBV satellite, did not block secretion of either empty or complete HBV virions. Together, these results indicate that both common and distinct signals on empty capsids vs. mature nucleocapsids interact with the S and L proteins during the formation of complete vs. empty virions. IMPORTANCE Hepatitis B virus (HBV) is a major cause of severe liver diseases including cirrhosis and cancer. In addition to the complete infectious virion particle, which contains an outer envelope layer and an interior capsid that, in turn, encloses a DNA genome, HBV infected cells also secrete non-infectious, incomplete viral particles in large excess over the complete virions. In particular, the empty (or genome-free) virion share with the complete virion the outer envelope and interior capsid but contain no genome. We have carried out a comparative study on the capsid and envelope requirements for the secretion of these two types of virion particles and uncovered both shared and distinct determinants on the capsid and envelope for their secretion. These results provide new information on HBV morphogenesis, and have implications for efforts to develop empty HBV virions as a novel biomarker and a new generation of HBV vaccine. Copyright © 2018 American Society for Microbiology.

Performance evaluation of poly-urethane foam packed-bed chemical scrubber for the oxidative absorption of NH3 and H2S gases.

PubMed

Nisola, Grace M; Valdehuesa, Kris Niño G; Anonas, Alex V; Ramos, Kristine Rose M; Lee, Won-Keun; Chung, Wook-Jin

2018-01-02

The feasibility of open-pore polyurethane (PU) foam as packing material for wet chemical scrubber was tested for NH 3 and H 2 S removals. The foam is inexpensive, light-weight, highly porous (low pressure drop) and provides large surface area per unit volume, which are desirable properties for enhanced gas/liquid mass transfer. Conventional HCl/HOCl (for NH 3 ) and NaOH/NaOCl (for H 2 S) scrubbing solutions were used to absorb and oxidize the gases. Assessment of the wet chemical scrubbers reveals that pH and ORP levels are important to maintain the gas removal efficiencies >95%. A higher re-circulation rate of scrubbing solutions also proved to enhance the performance of the NH 3 and H 2 S columns. Accumulation of salts was confirmed by the gradual increase in total dissolved solids and conductivity values of scrubbing solutions. The critical elimination capacities at >95% gas removals were found to be 5.24 g NH 3 -N/m 3 -h and 17.2 g H 2 S-S/m 3 -h at an empty bed gas residence time of 23.6 s. Negligible pressure drops (< 4 mm H 2 O) after continuous operation demonstrate the suitability of PU as a practical packing material in wet chemical scrubbers for NH 3 and H 2 S removals from high-volume dilute emissions.

Confirmation of Monod Model for Biofiltration of Styrene Vapors from Waste Flue Gas

PubMed Central

Dehghanzadeh, Reza; Roshani, Babak; Asadi, Mahzar; Fahiminia, Mohammad; AslHashemi, Ahmad

2012-01-01

Background: The objective of this research was to investigate the kinetic behavior of the biofil¬tration process for the removal of styrene. Methods: A three stage compost based biofilter was inoculated with thickened activated sludge. The reaction order rate constants were obtained from continuous experiments and used as the specific growth rate for the Monod equation. Results: The measured concentration profiles show a linear dependence on the bed height in the biofilter at higher loadings, such as 75 and 45 g m-3 h-1. This is the condition of reaction limitation for a reaction with zero-order kinetics. From the experimental data, maximum elimination capac¬ity (ECmax) was estimated to be 44, 40 and 26 g m-3 h-1 at empty bed retention times (EBRTs) of 120, 60 and 30 s, respectively. However, at lower loadings, the measured concentration profile of the biofilter is one of exponential increase, which is the condition of both reaction and diffusion limitations for a reaction with zero-order kinetics. Maximum elimination capacities found from the experimental results were the same as Monod model predictions. Both the experimental re¬sults and the model predictions showed the influence of EBRT on the removal rate of styrene, particularly for the highest loading rate. Conclusion: In terms of the practical applications of the proposed models have the advantage of being simpler than Monod kinetics and Monod kinetics requires a numerical solution. PMID:24688940

Differential Diagnosis and Treatment of Impaired Bladder Emptying

PubMed Central

Yoshimura, Naoki; Chancellor, Michael B

2004-01-01

Although much attention is paid to urinary incontinence, the condition of incomplete bladder emptying is becoming more common with the aging of the US population and the widespread use of anticholinergic drugs to treat overactive bladder. This disorder can often be silent until end-stage presentation of overflow incontinence. In this article, we review the pathophysiologic conditions of the bladder and urethra that can cause impaired bladder emptying and discuss how to evaluate and screen the patient with a bladder that does not empty. In addition, we provide an overview of treatment options available for impaired bladder emptying and consider the research that is under way to find the best therapies for the failing bladder. PMID:16985851

Treatment of Perchlorate-Contaminated Groundwater Using Highly-Selective, Regenerable Anion-Exchange Resins at Edwards Air Force Base

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gu, B.

2003-05-30

Selective ion exchange is one of the most effective treatment technologies for removing low levels of perchlorate (ClO{sub 4}{sup -}) from contaminated water because of its high efficiency without adverse impacts on the water quality caused by adding or removing any chemicals or nutrients. This report summarizes both the laboratory and a field pilot-scale studies to determine the ability and efficiency of the bifunctional synthetic resins to remove ClO{sub 4}{sup -} from the contaminated groundwater at the Edwards Air Force Base in California. Regeneration of the resins after groundwater treatment was also evaluated using the FeCl{sub 3}-HCl regeneration technique recentlymore » developed at Oak Ridge National Laboratory. On the basis of this study, the bifunctional resin, D-3696 was found to be highly selective toward ClO{sub 4}{sup -} and performed much better than one of the best commercial nitrate-selective resins (Purolite A-520E) and more than an order of magnitude better than the Purolite A-500 resin (with a relatively low selectivity). At an influent concentration of {approx} 450 {micro}g/L ClO{sub 4}{sup -} in groundwater, the bifunctional resin bed treated {approx} 40,000 empty bed volumes of groundwater before a significant breakthrough of ClO{sub 4}{sup -} occurred. The presence of relatively high concentrations of chloride and sulfate in site groundwater did not appear to affect the ability of the bifunctional resin to remove ClO{sub 4}{sup -}. However, the presence of high iron or iron oxyhydroxides and/or biomass in groundwater caused a significant fouling of the resin beds and greatly influenced the effectiveness in regenerating the resins sorbed with ClO{sub 4}{sup -}. Under such circumstances, a prefilter ({approx} 0.5-1 {micro}m) was found to be necessary to remove these particulates and to reduce the risk of fouling of the resin beds. Without significant fouling, the resin bed could be effectively regenerated by the FeCl{sub 3} displacement technique. Nearly 100% of the sorbed ClO{sub 4}{sup -} was displaced or recovered after elution with only {approx} 2-5 bed volumes of the FeCl{sub 3}-HCl regenerant solution. On the basis of both the laboratory and field pilot-scale studies, they therefore anticipate that a combination of the selective ion exchange and the FeCl{sub 3}-regeneration technologies may offer a cost-effective means to remove ClO{sub 4}{sup -} from contaminated groundwater with significantly reduced waste generation and operational cost.« less

Increase of transient lower esophageal sphincter relaxation associated with cascade stomach

PubMed Central

Kawada, Akiyo; Kusano, Motoyasu; Hosaka, Hiroko; Kuribayashi, Shiko; Shimoyama, Yasuyuki; Kawamura, Osamu; Akiyama, Junichi; Yamada, Masanobu; Akuzawa, Masako

2017-01-01

We previously reported that cascade stomach was associated with reflux symptoms and esophagitis. Delayed gastric emptying has been believed to initiate transient lower esophageal sphincter relaxation (TLESR). We hypothesized that cascade stomach may be associated with frequent TLESR with delayed gastric emptying. Eleven subjects with cascade stomach and 11 subjects without cascade stomach were enrolled. Postprandial gastroesophageal manometry and gastric emptying using a continuous 13C breath system were measured simultaneously after a liquid test meal. TLESR events were counted in early period (0–60 min), late period (60–120 min), and total monitoring period. Three parameters of gastric emptying were calculated: the half emptying time, lag time, and gastric emptying coefficient. The median frequency of TLESR events in the cascade stomach and non-cascade stomach groups was 6.0 (median), 4.6 (interquartile range) vs 5.0, 3.0 in the early period, 5.0, 3.2 vs 3.0, 1.8 in the late period, and 10.0, 6.2 vs 8.0, 5.0 in the total monitoring period. TLESR events were significantly more frequent in the cascade stomach group during the late and total monitoring periods. In contrast, gastric emptying parameters showed no significant differences between the two groups. We concluded that TLESR events were significantly more frequent in persons with cascade stomach without delayed gastric emptying. PMID:28584403

Disturbed gastric emptying in the short bowel syndrome. Evidence for a 'colonic brake'.

PubMed Central

Nightingale, J M; Kamm, M A; van der Sijp, J R; Morris, G P; Walker, E R; Mather, S J; Britton, K E; Lennard-Jones, J E

1993-01-01

Gastric emptying of liquid (orange juice containing technetium-99m (99mTc) labelled antimony sulphide colloid) and solid (570 kcal pancake containing 0.5 mm resin microspheres labelled with Indium-111 (111-In)) was measured in seven patients with jejunum and no colon (jejunal lengths 30-160 cm), six patients with jejunum in continuity with the colon (jejunal length 25-75 cm), and in 12 normal subjects. In patients with no colon early emptying of liquid was rapid (median 25% emptying: 7 v 25 min, no colon v normal, p < 0.05); early gastric emptying of solid was rapid in two (each with less than 100 cm jejunum) and normal in the other five. Gastric emptying of liquid and solid for patients with jejunum in continuity with the colon was normal for the first three hours. There was increased liquid and solid retained in the stomach at six hours in both groups of patients (p < 0.01). Small bowel transit time was faster than in normal subjects for liquid in both groups of patients (p < 0.05) and for solid in those with no colon (p < 0.05). Rapid gastric emptying of liquid may contribute to the large stomal output in patients with a high jejunostomy. Preservation of the colon after a major small intestinal resection exerts a braking effect on the rate of early gastric emptying of liquid. PMID:8406148

Evolution of the microstructure during the process of consolidation and bonding in soft granular solids.

PubMed

Yohannes, B; Gonzalez, M; Abebe, A; Sprockel, O; Nikfar, F; Kiang, S; Cuitiño, A M

2016-04-30

The evolution of microstructure during powder compaction process was investigated using a discrete particle modeling, which accounts for particle size distribution and material properties, such as plasticity, elasticity, and inter-particle bonding. The material properties were calibrated based on powder compaction experiments and validated based on tensile strength test experiments for lactose monohydrate and microcrystalline cellulose, which are commonly used excipient in pharmaceutical industry. The probability distribution function and the orientation of contact forces were used to study the evolution of the microstructure during the application of compaction pressure, unloading, and ejection of the compact from the die. The probability distribution function reveals that the compression contact forces increase as the compaction force increases (or the relative density increases), while the maximum value of the tensile contact forces remains the same. During unloading of the compaction pressure, the distribution approaches a normal distribution with a mean value of zero. As the contact forces evolve, the anisotropy of the powder bed also changes. Particularly, during loading, the compression contact forces are aligned along the direction of the compaction pressure, whereas the tensile contact forces are oriented perpendicular to direction of the compaction pressure. After ejection, the contact forces become isotropic. Copyright © 2016 Elsevier B.V. All rights reserved.

Direct comparison of solid-phase gastric emptying times assessed by means of a carbon isotope-labeled sodium acetate breath test and technetium Tc 99m albumin colloid radioscintigraphy in healthy cats.

PubMed

Schmitz, Silke; Götte, Birte; Borsch, Christian; Kunz, Clemens; Failing, Klaus; Neiger, Reto

2014-07-01

To directly compare solid-phase gastric emptying times assessed by means of a [(13)C]sodium acetate breath test ([(13)C]-SABT) and technetium Tc 99m albumin colloid radioscintigraphy ((99m)Tc-ACR) in healthy cats. 12 healthy cats. After ingestion of a test meal containing 50 mg of [(13)C]sodium acetate and 250 MBq of (99m)Tc-albumin colloid, each cat underwent simultaneous [(13)C]-SABT and (99m)Tc-ACR on 2 consecutive days. Breath samples and scintigrams were acquired at 30, 60, 90, 120, 150, 180, 210, 240, 300, 360, 480, and 600 minutes after meal ingestion. Quartiles of gastric emptying (25%, 50%, and 75%) were calculated for breath test analysis by use of the area under the curve of the (13)C:(12)C ratio. Quartiles of gastric emptying times were extrapolated from the scintigraphic findings by beans of nonlinear curve regression analysis. Mean ± SD gastric half-emptying (50%) times obtained with [(13)C]-SABT and (99m)Tc-ACR, were 239 ± 28 minutes and 276 ± 59 minutes, respectively. A 2-way repeated-measures ANOVA revealed that mean gastric emptying times determined with [(13)C]-SABT and (99m)Tc-ACR differed significantly. For the stages of gastric emptying, Pearson correlation between the 2 methods was good at 25% (r = 0.655) and weak at 50% (r = 0.588) and 75% (r = 0.566)of gastric emptying. Results indicated that the [(13)C]-SABT can be a valid alternative to (99m)Tc-ACR in healthy cats; it was easy to perform, was tolerated well by the cats, and had acceptable correlation to scintigraphic findings at gastric emptying of 25%, 50% and 75%. Studies in cats with delayed gastric emptying will be needed to verify the validity of the [(13)C]-SABT.

Risk factors associated with delayed gastric emptying after subtotal gastrectomy with Billroth-I anastomosis using circular stapler for early gastric cancer patients

PubMed Central

Kim, Ki Han; Jung, Ghap Joong

2012-01-01

Purpose Gastric surgery may potentiate delayed gastric emptying. Billroth I gastroduodenostomy using a circular stapler is the most preferable reconstruction method. The purpose of this study is to analyze the risk factors associated with delayed gastric emptying after radical subtotal gastrectomy with Billroth I anastomosis using a stapler for early gastric cancer. Methods Three hundred and seventy-eight patients who underwent circular stapled Billroth I gastroduodenostomy after subtotal gastrectomy due to early gastric cancer were analyzed retrospectively. One hundred and eighty-two patients had Billroth I anastomosis using a 25 mm diameter circular stapler, and 196 patients had anastomosis with a 28 or 29 mm diameter circular stapler. Clinicopathological features and postoperative outcomes were evaluated and compared between the two groups. Delayed gastric emptying was diagnosed by symptoms and simple abdomen X-ray with or without upper gastrointestinal series or endoscopy. Results Postoperative delayed gastric emptying was found in 12 (3.2%) of the 378 patients. Among all the variables, distal margin and circular stapler diameter were significantly different between the cases with delayed gastric emptying and no delayed gastric emptying. There were statistically significant differences in sex, body mass index, comorbidity, complication, and operation type according to circular stapler diameter. In both univariate and multivariate logistic regression analyses, only the stapler diameter was found to be a significant factor affecting delayed gastric emptying (P = 0.040). Conclusion In this study, the circular stapler diameter was one of the most significant predictable factors of delayed gastric emptying for Billroth I gastroduodenostomy. The use of a 28 or 29 mm diameter circular stapler rather than a 25 mm diameter stapler in stapled gastroduodenostomy for early gastric cancer can reduce postoperative delayed gastric emptying associated with anastomosic stenosis or edema with relative safety. PMID:23166886

[Effect of erythromycin on electrical activity and gastric emptying of the intrathoracic stomach after esophagectomy for esophageal cancer].

PubMed

Liu, Jun-feng; Liu, Cheng-jun; Shi, Zhi-hua; Liu, Xin-bo; Jiang, Tao; Wang, Fu-shun; Cao, Fu-min; Li, Bao-qing

2013-09-01

To investigate the effect of erythromycin on electrical activity and emptying of the intrathoracic stomach after esophagectomy for esophageal cancer. Thirty patients undergoing esophagectomy for cancer and esophagogastrostomy above the aortic arch were divided into the study group (n=15) and the control group (n=15). Electrogastrography and radionuclide gastric emptying were examined for these patients before and 1, 3, 6, 12 months after surgery. Patients in the study group received erythromycin (0.25 g tid po) for 1 week before examination. The wave amplitude (Uv), dominant frequency (CPM) and percentage of normal slow wave (%) of electrogastrogram decreased after surgery and returned to normal at the first postoperative month in the study group and the 12th postoperative month in the control group (P>0.05). Gastric emptying was significantly delayed after esophagectomy, and returned to normal one year after operation in the study group (P>0.05). However, gastric emptying remained abnormal in the control group (P<0.01). Erythromycin improves electrical activity and emptying of the stomach after esophagectomy for cancer. Gastric emptying recovery later than the recovery of electrical activity, which may be related to gastric ischemia and edema.

Performance and bacterial diversity of biotrickling filters filled with conductive packing material for the treatment of toluene.

PubMed

Wu, Hao; Guo, Chunyu; Yin, Zhenhao; Quan, Yue; Yin, Chengri

2018-06-01

Toluene has high toxicity and mutagenicity, thus, the removal of toluene from air is necessary. In this study, two biotrickling filters (BTFs) were constructed and packed with conductive packing material to treat toluene waste gas. BTF-O exhibited good toluene removal performance even under high toluene inlet concentration, and over 80% of removal efficiency was observed. The elimination capacity reached 120.1 g/m 3  h corresponding to an inlet concentration of 2.259 g/m 3 under 61.5 s of empty bed retention time. During toluene biodegradation, the output voltage was observed in BTF-O and BTF-E, moreover BTF-E also showed slight power storage capacity. The applied voltage inhibited toluene removal and affected the bacterial community. The predominant bacterial genera in BTF-O were Acidovorax, Rhodococcus, Hydrogenophaga, Brevundimonas, Arthrobacter, Pseudoxanthomonas, Devosia, Gemmobacter, Rhizobium, Dokdonella and Pseudomonas. Genera Xanthobacter and Pelomonas accounted for the main bacterial community in BTF-E. Copyright © 2018 Elsevier Ltd. All rights reserved.

Modelling of percolation rate of stormwater from underground infiltration systems.

PubMed

Burszta-Adamiak, Ewa; Lomotowski, Janusz

2013-01-01

Underground or surface stormwater storage tank systems that enable the infiltration of water into the ground are basic elements used in Sustainable Urban Drainage Systems (SUDS). So far, the design methods for such facilities have not taken into account the phenomenon of ground clogging during stormwater infiltration. Top layer sealing of the filter bed influences the infiltration rate of water into the ground. This study presents an original mathematical model describing changes in the infiltration rate variability in the phases of filling and emptying the storage and infiltration tank systems, which enables the determination of the degree of top ground layer clogging. The input data for modelling were obtained from studies conducted on experimental sites on objects constructed on a semi-technological scale. The experiment conducted has proven that the application of the model developed for the phase of water infiltration enables us to estimate the degree of module clogging. However, this method is more suitable for reservoirs embedded in more permeable soils than for those located in cohesive soils.

Microbial Community in a Biofilter for Removal of Low Load Nitrobenzene Waste Gas

PubMed Central

Zhai, Jian; Wang, Zhu; Shi, Peng; Long, Chao

2017-01-01

To improve biofilter performance, the microbial community of a biofilter must be clearly defined. In this study, the performance of a lab-scale polyurethane biofilter for treating waste gas with low loads of nitrobenzene (NB) (< 20 g m-3 h-1) was investigated when using different empty bed residence times (EBRT) (64, 55.4 and 34 s, respectively). In addition, the variations of the bacterial community in the biofilm on the longitudinal distribution of the biofilters were analysed by using Illumina MiSeq high-throughput sequencing. The results showed that NB waste gas was successfully degraded in the biofilter. High-throughput sequencing data suggested that the phylum Actinobacteria and genus Rhodococcus played important roles in the degradation of NB. The variations of the microbial community were attributed to the different intermediate degradation products of NB in each layer. The strains identified in this study were potential candidates for purifying waste gas effluents containing NB. PMID:28114416

Potential application of an Aspergillus strain in a pilot biofilter for benzene biodegradation

PubMed Central

Sun, Da; Zhang, Kun; Duan, Chuanren; Wu, Wei; Deng, Daiyong; Yu, Donghong; Shahzad, M. Babar; Xu, Dake; Tang, Ju; Luo, Li; Chen, Jia; Wang, Jinxuan; Chen, Yidan; Xie, Xiang; Wang, Guixue

2017-01-01

A biofilter with fungus was developed for efficient degradation of benzene, which can overcome the potential risk of leakage commonly found in such services. Results indicated that the optimum parameter values were temperature 40 °C, pH 6, and 500 mg L−1 of the initial benzene concentration. Besides, the empty bed residence time and inlet load range of biofilter were set to 20 s and 21.23–169.84 g m−3 h−1 respectively. Under these conditions, this biofilter can obtain the maximum removal efficiency of more than 90%, the eliminating capacity could be up to 151.67 g m−3 h−1. Furthermore, scanning electron microscopy was used to investigate three filler materials for packing fungus biofilm. This is the first study introducing an Aspergillus strain for benzene removal and these results highlight that the development of this biofilter has the potential scaling-up application as gas-processing of industrial wastes. PMID:28383064

Transient Characterization of Type B Particles in a Transport Riser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shadle, L.J.; Monazam, E.R.; Mei, J.S.

2007-01-01

Simple and rapid dynamic tests were used to evaluate fluid dynamic behavior of granular materials in the transport regime. Particles with densities ranging from 189 to 2,500 kg/m3 and Sauter mean size from 61 to 812 μm were tested in a 0.305 m diameter, 15.5 m height circulating fluidized bed (CFB) riser. The transient tests involved the abrupt stoppage of solids flow for each granular material over a wide range gas flow rates. The riser emptying time was linearly related to the Froude number in each of three different operating regimes. The flow structure along the height of the risermore » followed a distinct pattern as tracked through incremental pressures. These results are discussed to better understand the transformations that take place when operating over various regimes. During the transients the particle size distribution was measured. The effects of pressure, particle size, and density on test performance are also presented.« less

Potential application of an Aspergillus strain in a pilot biofilter for benzene biodegradation

NASA Astrophysics Data System (ADS)

Sun, Da; Zhang, Kun; Duan, Chuanren; Wu, Wei; Deng, Daiyong; Yu, Donghong; Shahzad, M. Babar; Xu, Dake; Tang, Ju; Luo, Li; Chen, Jia; Wang, Jinxuan; Chen, Yidan; Xie, Xiang; Wang, Guixue

2017-04-01

A biofilter with fungus was developed for efficient degradation of benzene, which can overcome the potential risk of leakage commonly found in such services. Results indicated that the optimum parameter values were temperature 40 °C, pH 6, and 500 mg L-1 of the initial benzene concentration. Besides, the empty bed residence time and inlet load range of biofilter were set to 20 s and 21.23-169.84 g m-3 h-1 respectively. Under these conditions, this biofilter can obtain the maximum removal efficiency of more than 90%, the eliminating capacity could be up to 151.67 g m-3 h-1. Furthermore, scanning electron microscopy was used to investigate three filler materials for packing fungus biofilm. This is the first study introducing an Aspergillus strain for benzene removal and these results highlight that the development of this biofilter has the potential scaling-up application as gas-processing of industrial wastes.

Municipal-wastewater treatment using upflow-anaerobic filters.

PubMed

Manariotis, loannis D; Grigoropoulos, Sotirios G

2006-03-01

Three 12.5-L upflow-anaerobic filters (AF), with ceramic-saddle, plastic-ring, and crushed-stone packing, were used to evaluate the sustained treatment of municipal wastewater. The reactors were initially fed dogfood-fortified wastewater and then raw municipal wastewater, and operated at 25.4 degrees C (32 months) and 15.5 degrees C (2 months). During 23 months, the AF units treated municipal wastewater (mean chemical oxygen demand [COD] 442 mg/L and total suspended solids [TSS] 247 mg/L), the hydraulic retention time (HRT) ranged from 3.1 to 0.30 d (empty bed), and the organic loading rate ranged from 0.115 to 1.82 kg COD/m3d. At the higher temperature and an HRT (void volume) of 1.0 d, COD and TSS removals ranged from 74 to 79% and 95 to 96%, respectively; however, efficiencies declined substantially at HRT values less than 0.4 d. Reactor performance, under the same hydraulic and organic loadings, deteriorated with time and was adversely affected by lower temperature.

Integrated nitrogen removal biofilter system with ceramic membrane for advanced post-treatment of municipal wastewater.

PubMed

Son, Dong-Jin; Yun, Chan-Young; Kim, Woo-Yeol; Zhang, Xing-Ya; Kim, Dae-Gun; Chang, Duk; Sunwoo, Young; Hong, Ki-Ho

2016-12-01

The pre-denitrification biofilm process for nitrogen removal was combined with ceramic membrane with pore sizes of 0.05-0.1 µm as a system for advanced post-treatment of municipal wastewater. The system was operated under an empty bed hydraulic retention time of 7.8 h, recirculation ratio of 3, and transmembrane pressure of 0.47 bar. The system showed average removals of organics, total nitrogen, and solids as high as 93%, 80%, and 100%, respectively. Rapid nitrification could be achieved and denitrification was performed in the anoxic filter without external carbon supplements. The residual particulate organics and nitrogen in effluent from biofilm process could be also removed successfully through membrane filtration and the removal of total coliform was noticeably improved after membrane filtration. Thus, a system composed of the pre-denitrification biofilm process with ceramic membrane would be a compact and flexible option for advanced post-treatment of municipal wastewater.

Effect of temperature on pyrolysis product of empty fruit bunches

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rahman, Aizuddin Abdul; Sulaiman, Fauziah; Abdullah, Nurhayati

2015-04-24

Pyrolysis of empty fruit bunches (EFB) was performed in a fixed bed reactor equipped with liquid collecting system. Pyrolysis process was conducted by varying the terminal pyrolysis temperature from 300 to 500°C under heating rate of 10°C/min for at least 2 hours. Char yield was obtained highest at 300°C around 55.88 wt%, and started to decrease as temperature increase. The maximum yield of pyrolysis liquid was obtained around 54.75 wt% as pyrolysis temperature reach 450°C. For gas yield percentage, the yield gained as temperature was increased from 300 to 500°C, within the range between 8.44 to 19.32 wt%. The charmore » obtained at 400°C has great potential as an alternative solid fuel, due to its high heating value of 23.37 MJ/kg, low in volatile matter and ash content which are approximately around 40.32 and 11.12 wt%, respectively. The collected pyrolysis liquid within this temperature range found to have high water content of around 16.15 to 18.20 wt%. The high aqueous fraction seemed to cause the pyrolysis liquid to have low HHV which only ranging from 10.81 to 12.94 MJ/kg. These trends of results showed that necessary enhancement should be employ either on the raw biomass or pyrolysis products in order to approach at least the minimum quality of common hydrocarbon solid or liquid fuel. For energy production, both produced bio-char and pyrolysis liquid are considered as sustainable sources of bio-energy since they contained low amounts of nitrogen and sulphur, which are considered as environmental friendly solid and liquid fuel.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Junay, A.; Guézo, S., E-mail: sophie.guezo@univ-rennes1.fr; Turban, P.

We study structural and electronic inhomogeneities in Metal—Organic Molecular monoLayer (OML)—semiconductor interfaces at the sub-nanometer scale by means of in situ Ballistic Electron Emission Microscopy (BEEM). BEEM imaging of Au/1-hexadecanethiols/GaAs(001) heterostructures reveals the evolution of pinholes density as a function of the thickness of the metallic top-contact. Using BEEM in spectroscopic mode in non-short-circuited areas, local electronic fingerprints (barrier height values and corresponding spectral weights) reveal a low-energy tunneling regime through the insulating organic monolayer. At higher energies, BEEM evidences new conduction channels, associated with hot-electron injection in the empty molecular orbitals of the OML. Corresponding band diagrams at buriedmore » interfaces can be thus locally described. The energy position of GaAs conduction band minimum in the heterostructure is observed to evolve as a function of the thickness of the deposited metal, and coherently with size-dependent electrostatic effects under the molecular patches. Such BEEM analysis provides a quantitative diagnosis on metallic top-contact formation on organic molecular monolayer and appears as a relevant characterization for its optimization.« less

Specific esophagogram to assess functional outcomes after Heller's myotomy and Dor's fundoplication for esophageal achalasia.

PubMed

Tsoukali, E; Gouvas, N; Tsiaoussis, J; Pechlivanides, G; Zervakis, N; Mantides, A; Xynos, E

2011-09-01

Esophageal emptying assessed at the 'timed barium' esophagogram correlates well with symptomatic outcomes after pneumatic dilation for esophageal achalasia, although 30% of patients with satisfactory outcome exhibit partial improvement in emptying. The aim of the study was to investigate any correlation of esophageal emptying to symptomatic response after laparoscopic Heller's myotomy and Dor's fundoplication. 'Bread and barium' (transit time of a barium opaque bread bolus) and 'timed barium' (height of esophageal barium column 5 minutes after ingestion of 200-250 mL of barium suspension) esophagogram was used to assess esophageal emptying in 73 patients with esophageal achalasia before 1 and 5 years (31 cases) after laparoscopic myotomy and anterior fundoplication. Symptoms assessment was based to a specific score. At 1-year follow-up, excellent and good symptomatic results were obtained in 95% of the cases. Esophageal maximum diameter, esophageal transit time, and esophageal barium column were significantly correlated to each other and to symptom score postoperatively (P < 0.001). Complete and partial (<90% and 50-90% postoperative reduction in barium column, respectively) emptying was seen in 55% and 31% of patients with excellent result. Patients with a pseudodiverticulum postoperatively had a more delayed esophageal emptying than those without. Symptomatic outcome and esophageal emptying did not deteriorate at 5-year follow-up. Esophageal emptying assessed by 'barium and bread' and 'timed barium' esophagogram correlated well with symptomatic outcome after laparoscopic myotomy for esophageal achalasia. Complete symptomatic relief does not necessarily reflect complete esophageal emptying. Outcomes do not deteriorate by time. Because of wide availability, esophagogram can be applied in follow-up of postmyotomy patients in conjunction with symptomatic evaluation. © 2011 Copyright the Authors. Journal compilation © 2011, Wiley Periodicals, Inc. and the International Society for Diseases of the Esophagus.

Effects of rehabilitation management on gastric emptying function in older adults with diabetes.

PubMed

Shao, Z M; Yao, J F; Chen, J; Yu, Z W; Yu, X F; Zheng, J J; Tang, X

2014-01-24

The relationship between gastric emptying dysfunction and blood glucose concentration in elderly with type 2 diabetes mellitus was investigated, and the effect of rehabilitation exercise prescription training on gastric emptying in the geriatric diabetic patients was evaluated. A total of 160 older type 2 diabetic adults and 30 cases of non-diabetic patients were studied with regard to the gastric half emptying time (GET1/2) of solid meals radiolabelled with 99mTc. Eighty delayed gastric emptying diabetic patients were randomly divided into 4 four groups: rehabilitation exercise + mosapride group (N = 20), rehabilitation exercise group (N = 20), mosapride group (N = 20), and control group (N = 20). The level of blood glucose was measured every six months in a two-year follow-up. The solid GET1/2 of regulated blood glycemic control patients showed no statistically significant differences from non-diabetic patients (P > 0.05). However, the value for poor blood glycemic control patients exhibited significant statistical differences compared with both non-diabetic (P < 0.01) and regulated blood glycemic control group patients (P < 0.01). It showed that the gastric emptying time improved in the rehabilitation exercise group, mosapride group and rehabilitation exercise group + mosapride group after two years of treatment (P < 0.05). Fasting blood glucose in both rehabilitation exercise group and rehabilitation exercise + mosapride group was significantly decreased. Postprandial blood glucose in the rehabilitation exercise group, mosapride group, rehabilitation exercise group + mosapride group was significantly decreased. High blood glucose level can delay gastric emptying in older type 2 diabetic patients. Gastric emptying and blood glucose control affect each other. It was shown that appropriate rehabilitation exercise combined with prokinetic agent may improve gastric emptying in some geriatric type 2 diabetic patients and help control their blood glucose.

Gastric emptying, postprandial blood pressure, glycaemia and splanchnic flow in Parkinson's disease.

PubMed

Trahair, Laurence G; Kimber, Thomas E; Flabouris, Katerina; Horowitz, Michael; Jones, Karen L

2016-05-28

To determine gastric emptying, blood pressure, mesenteric artery blood flow, and blood glucose responses to oral glucose in Parkinson's disease. Twenty-one subjects (13 M, 8 F; age 64.2 ± 1.6 years) with mild to moderate Parkinson's disease (Hoehn and Yahr score 1.4 ± 0.1, duration of known disease 6.3 ± 0.9 years) consumed a 75 g glucose drink, labelled with 20 MBq (99m)Tc-calcium phytate. Gastric emptying was quantified with scintigraphy, blood pressure and heart rate with an automated device, superior mesenteric artery blood flow by Doppler ultrasonography and blood glucose by glucometer for 180 min. Autonomic nerve function was evaluated with cardiovascular reflex tests and upper gastrointestinal symptoms by questionnaire. The mean gastric half-emptying time was 106 ± 9.1 min, gastric emptying was abnormally delayed in 3 subjects (14%). Systolic and diastolic blood pressure fell (P < 0.001) and mesenteric blood flow and blood glucose (P < 0.001 for both) increased, following the drink. Three subjects (14%) had definite autonomic neuropathy and 8 (38%) had postprandial hypotension. There were no significant relationships between changes in blood pressure, heart rate or mesenteric artery blood flow with gastric emptying. Gastric emptying was related to the score for autonomic nerve function (R = 0.55, P < 0.01). There was an inverse relationship between the blood glucose at t = 30 min (R = -0.52, P < 0.05), while the blood glucose at t = 180 min was related directly (R = 0.49, P < 0.05), with gastric emptying. In mild to moderate Parkinson's disease, gastric emptying is related to autonomic dysfunction and a determinant of the glycaemic response to oral glucose.

Mosapride Accelerates the Delayed Gastric Emptying of High-Viscosity Liquids: A Crossover Study Using Continuous Real-Time 13C Breath Test (BreathID System)

PubMed Central

Sakamoto, Yasunari; Sekino, Yusuke; Yamada, Eiji; Ohkubo, Hidenori; Higurashi, Takuma; Sakai, Eiji; Iida, Hiroshi; Hosono, Kunihiro; Endo, Hiroki; Nonaka, Takashi; Ikeda, Tamon; Fujita, Koji; Yoneda, Masato; Koide, Tomoko; Takahashi, Hirokazu; Goto, Ayumu; Abe, Yasunobu; Gotoh, Eiji; Maeda, Shin; Nakajima, Atsushi

2011-01-01

Background/Aims The administration of liquid nutrients to patients is often accompanied by complications such as gastroesophageal reflux. To prevent gastroesophageal reflux, high-viscosity liquid meals are used widely, however, it still remains controversial whether high-viscosity liquid meals have any effect on the rate of gastric emptying. The present study was conducted with the aim of determining whether high-viscosity liquid meals had any effect on the rate of gastric emptying and mosapride might accelerate the rate of gastric emptying of high-viscosity liquid meals. Methods Six healthy male volunteers underwent 3 tests at intervals of > 1 week. After fasting for > 8 hours, each subject received one of three test meals (liquid meal only, high-viscosity liquid meal [liquid meal plus pectin] only, or high-viscosity liquid meal 30 minutes after intake of mosapride). A 13C-acetic acid breath test was performed, which monitored the rate of gastric emptying for 4 hours. Using the Oridion Research Software (β version), breath test parameters were calculated. The study parameters were examined for all the 3 test conditions and compared using the Freidman test. Results Gastric emptying was significantly delayed following intake of a high-viscosity liquid meal alone as compared with a liquid meal alone; however, intake of mosapride prior to a high-viscosity liquid meal was associated with a significantly accelerated rate of gastric emptying as compared with a high-viscosity liquid meal alone. Conclusions This study showed that high-viscosity liquid meals delayed gastric emptying: however, mosapride recovered the delayed rate of gastric emptying by high-viscosity liquid meals. PMID:22148109

[Force-based local navigation in robot-assisted implantation bed anlage in the lateral skull base. An experimental study].

PubMed

Plinkert, P K; Federspil, P A; Plinkert, B; Henrich, D

2002-03-01

Excellent precision, miss of retiring, reproducibility are main characteristics of robots in the operating theatre. Because of these facts their use for surgery in the lateral scull base is of great interest. In recent experiments we determined process parameters for robot assisted reaming of a cochlea implant bed and for a mastoidectomy. These results suggested that optimizing parameters for thrilling with the robot is needed. Therefore we implemented a suitable reaming curve from the geometrical data of the implant and a force controlled process control for robot assisted reaming at the lateral scull base. Experiments were performed with an industrial robot on animal and human scull base specimen. Because of online force detection and feedback of sensory data the reaming with the robot was controlled. With increasing force values above a defined limit feed rates were automatically regulated. Furthermore we were able to detect contact of the thrill to dura mater by analyzing the force values. With the new computer program the desired implant bed was exactly prepared. Our examinations showed a successful reaming of an implant bed in the lateral scull base with a robot. Because of a force controlled reaming process locale navigation is possible and enables careful thrilling with a robot.

Behavioral effects of sublethal exposure to a combination of β-cyfluthrin and imidacloprid in the bed bug, Cimex lectularius L.

PubMed

Crawley, Sydney E; Kowles, Katelyn A; Gordon, Jennifer R; Potter, Michael F; Haynes, Kenneth F

2017-03-01

Bed bugs (Cimex lectularius) are blood-feeding insect pests with public health relevance. Their rapid evolution of resistance to pyrethroids has prompted a shift to combination products that include both a pyrethroid and neonicotinoid insecticide. Insecticides have both a direct impact on mortality and an indirect effect on behavior. Thus, we assessed the sublethal effects of a widely used combination product containing β-cyfluthrin (a pyrethroid) and imidacloprid (a neonicotinoid), as unexpected behavioral changes after exposure have been known to affect efficacy of insecticides. We found that bed bugs exposed to sublethal doses of a combination product containing β-cyfluthrin and imidacloprid did not feed as effectively as untreated bugs. Their locomotion behavior was also reduced. However, aggregation in response to the presence of conspecific harborages was not affected by sublethal exposure. Bed bugs exhibit behavioral changes after sublethal exposure to a combination product that could affect pest management choices and outcomes. A reduction in host-finding efficiency and feeding could complement the lethal effects of the insecticide. Alternatively, reduced locomotion following exposure could limit ongoing contact with insecticide deposits. However, an overall reduction in movement indicates that treatments are unlikely to cause dispersal of bugs to adjacent dwellings. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

The Frasnian-Famennian boundary (Upper Devonian) within the Hanover-Dunkirk transition, northern Appalachian basin, western New York state

DOE Office of Scientific and Technical Information (OSTI.GOV)

Over, D.J.

In western New York State interbedded pyritic silty green and dark grey shales and siltstone of the Hanover Member, Java Formation, West Falls Group, are overlain by thick pyritic dark grey-black shale of the Dunkirk Member of the Canadaway formation. The dark shales in the upper Hanover and Dunkirk contain a diverse and well preserved conodont fauna which allows precise placement of the Frasnian-Famennian boundary at several described sections. At Pt. Gratiot, in far western New York State, the contact between the Hanover and Dunkirk is disconformable. The Frasnian-Famennian boundary is marked by a pyritic lag deposit at the basemore » of the Dunkirk which contains Palmatolepis triangularis and Pa. subperlobata. The underlying upper Hanover is characterized by Pa. bogartensis , Pa. cf. Pa. rhenana, Pa. winchelli, and Ancyrognathus (asymmetricus/calvini) Eastward, in the direction of the paleo-source area, the Frasnian-Famennian boundary is within the upper Hanover Member. At Irish Gulf the boundary is recognized within a 10 cm thick laminated pyritic dark grey shale bed 3.0 m below the base of the Dunkirk. Palmatolepis triangularis and Pa. subperlobata occur below a conodont-rich lag layer in the upper 2 cm of the bed. Palmatolepis bogartensis , Pa. cf. Pa. rhenana, Ancyrodella curvata, and Icriodus alternatus occur in the underlying 8 cm. Palmatolepis triangularis and Pa. winchelli occur in an underlying dark shale bed separated from the boundary bed by a hummocky cross-bedded siltstone layer.« less

[*C]octanoic acid breath test to measure gastric emptying rate of solids.

PubMed

Maes, B D; Ghoos, Y F; Rutgeerts, P J; Hiele, M I; Geypens, B; Vantrappen, G

1994-12-01

We have developed a breath test to measure solid gastric emptying using a standardized scrambled egg test meal (250 kcal) labeled with [14C]octanoic acid or [13C]octanoic acid. In vitro incubation studies showed that octanoic acid is a reliable marker of the solid phase. The breath test was validated in 36 subjects by simultaneous radioscintigraphic and breath test measurements. Nine healthy volunteers were studied after intravenous administration of 200 mg erythromycin and peroral administration of 30 mg propantheline, respectively. Erythromycin significantly enhanced gastric emptying, while propantheline significantly reduced gastric emptying rates. We conclude that the [*C]octanoic breath test is a promising and reliable test for measuring the gastric emptying rate of solids.

Delayed Gastric Emptying after Living Donor Hepatectomy for Liver Transplantation

PubMed Central

Griesemer, Adam D.; Parsons, Ronald F.; Graham, Jay A.; Emond, Jean C.; Samstein, Benjamin

2014-01-01

Delayed gastric emptying is a significant postoperative complication of living donor hepatectomy for liver transplantation and may require endoscopic or surgical intervention in severe cases. Although the mechanism of posthepatectomy delayed gastric emptying remains unknown, vagal nerve injury during intraoperative dissection and adhesion formation postoperatively between the stomach and cut liver surface are possible explanations. Here, we present the first reported case of delayed gastric emptying following fully laparoscopic hepatectomy for living donor liver transplantation. Additionally, we also present a case in which symptoms developed after open right hepatectomy, but for which dissection for left hepatectomy was first performed. Through our experience and these two specific cases, we favor a neurovascular etiology for delayed gastric emptying after hepatectomy. PMID:25610698

Simulation of empty container logistic management at depot

NASA Astrophysics Data System (ADS)

Sze, San-Nah; Sek, Siaw-Ying Doreen; Chiew, Kang-Leng; Tiong, Wei-King

2017-07-01

This study focuses on the empty container management problem in a deficit regional area. Deficit area is the area having more export activities than the import activities, which always have a shortage of empty container. This environment has challenged the trading companies in the decision making in distributing the empty containers. A simulation model that fit to the environment is developed. Besides, a simple heuristic algorithm with some hard and soft constraints consideration are proposed to plan the logistic of empty container supply. Then, the feasible route with the minimum cost will be determined by applying the proposed heuristic algorithm. The heuristic algorithm can be divided into three main phases which are data sorting, data assigning and time window updating.

Effects of Swertia japonica extract and its main compound swertiamarin on gastric emptying and gastrointestinal motility in mice.

PubMed

Kimura, Yoshiyuki; Sumiyoshi, Maho

2011-09-01

The Swertia japonica is used clinically as a remedy for gastrointestinal symptoms in Japan. We examined the effects of a S. japonica and swertiamarin on gastric emptying and gastrointestinal motility in atropine-, dopamine-, and 5-hydroxytryptamine (5-HT)-treated mice. All three preparations inhibited reductions in gastric emptying and gastrointestinal motility induced by dopamine (1mg/kg, intraperitoneal injection, ip). Neither the powder, swertiamarin, nor itopride had any effect on the reductions in gastric emptying and gastrointestinal motility caused by 5-HT (4 mg/kg, ip). These findings suggest that the powder and swertiamarin stimulate gastric emptying and gastrointestinal motility by inhibiting the dopamine D(2) receptor. Copyright © 2011 Elsevier B.V. All rights reserved.

Initialization and Setup of the Coastal Model Test Bed: STWAVE

DTIC Science & Technology

2017-01-01

Laboratory (CHL) Field Research Facility (FRF) in Duck , NC. The improved evaluation methodology will promote rapid enhancement of model capability and focus...Blanton 2008) study . This regional digital elevation model (DEM), with a cell size of 10 m, was generated from numerous datasets collected at different...INFORMATION: For additional information, contact Spicer Bak, Coastal Observation and Analysis Branch, Coastal and Hydraulics Laboratory, 1261 Duck Road

Glacial Erosion Driven by Seasonal Shifts in Meltwater Drainage

NASA Astrophysics Data System (ADS)

Ugelvig, S. V.; Egholm, D. L.

2017-12-01

Subglacial erosion processes, like abrasion and quarrying, have been studied for decades. While models for abrasion clearly points to sliding speed as a primary control on abrasion rates, quarrying rates are thought to be governed by more complex combinations of sliding speed, effective pressure, bedrock slope and short-term water pressure fluctuations. Early models for quarrying focused on the deviatoric stress needed for growth of small isolated cracks in otherwise homogeneous intact bedrock. The rate-limiting factor for quarrying was thus the subcritical crack growth. Later studies have included effects of pre-existing fractures in the bedrock that weaken the rock. Here the strength distribution in the rock is based on the assumption that larger rock bodies have lower strength, because they have a higher probability of containing a weak fracture. However, this approach has been hampered by the assumption of steady-state cavity configuration. Here we attempt to combine previous model efforts in a model that tracks the temporal evolution of cavities while including a statistical treatment of bedrock strength. Using a two-dimensional finite-difference model, we simulate the spatial and temporal evolution of the hydrological system at the base of a glacier, while simultaneously computing rates of abrasion and quarrying. Cavity lengths and channel cross-sections evolve through time, which allow us to study how temporal shifts in ice-bed contact area and deviatoric stress influence quarrying rates over the course of a year. Furthermore, we use the temporal evolution of contact area between ice and bed to predict basal sliding speed and scale abrasion rates. Our results suggest that ice-bed contact area is a key variable in controlling sliding speed and rates of glacial erosion on seasonal time scales, where the subglacial drainage system reorganizes to accommodate the variations in surface melt rates. However, on diurnal timescales cavities and channels cannot adjust to the relatively rapid changes in meltwater input, which causes large fluctuations in water pressure. This in turn elevates the deviatoric stress in the bedrock and pressure fluctuations are thus on diurnal timescales found to dictate quarrying rates as well as abrasion rates.

Reach Out and Eat: Food and Beverages Depicted in Books for Preschoolers.

PubMed

England, Jessica L; Linchey, Jennifer; Madsen, Kristine A; Patel, Anisha I

2015-11-01

To examine food and beverage depictions in books for preschoolers. Books for preschoolers from Reach Out and Read (ROR; n = 42), public library (n = 27), and Publisher's Weekly booklists (n = 31) were examined for nutritive and empty-calorie food and beverage depictions. It was found that 66% of books depicted at least 1 food or beverage. More books depicted nutritive items than empty-calorie items (87.5% vs 54.7%, P < .001). There was a trend toward fewer empty-calorie depictions in ROR books than in other booklists. Yet nearly half of ROR books depicted at least 1 empty-calorie item. ROR books also accounted for 5 of 10 books with the most empty-calorie item depictions and 3 of 4 books with branding. With regard to messaging, approximately a third of books with the most empty-calorie depictions promoted unhealthy foods. When selecting books for ROR, it may be important to consider food and beverage depictions and messages. © The Author(s) 2015.

Reach Out and Eat: Food and Beverages Depicted in Books for Preschoolers

PubMed Central

England, Jessica L.; Linchey, Jennifer; Madsen, Kristine A.; Patel, Anisha I.

2015-01-01

Objective To examine food and beverage depictions in books for preschoolers. Methods Books for preschoolers from Reach Out and Read (ROR; n = 42), public library (n = 27), and Publisher's Weekly booklists (n = 31) were examined for nutritive and empty-calorie food and beverage depictions. Results It was found that 66% of books depicted at least I food or beverage. More books depicted nutritive items than empty-calorie items (87.5% vs 54.7%, P < .001). There was a trend toward fewer empty-calorie depictions in ROR books than in other booklists. Yet nearly half of ROR books depicted at least I empty-calorie item. ROR books also accounted for 5 of 10 books with the most empty-calorie item depictions and 3 of 4 books with branding. With regard to messaging, approximately a third of books with the most empty-calorie depictions promoted unhealthy foods. Conclusions When selecting books for ROR, it may be important to consider food and beverage depictions and messages. PMID:25715825

Postpyloric regulation of gastric emptying in rhesus monkeys.

PubMed

McHugh, P R; Moran, T H; Wirth, J B

1982-09-01

Saline (0.9% NaCl) empties rapidly and exponentially from the stomach of the rhesus monkey, but glucose solutions empty at a calorie-constant rate of 0.4 kcal/min. By means of indwelling intragastric and intraduodenal cannulae we can demonstrate an inhibition on the delivery of saline from the stomach provoked by glucose placed beyond the pylorus. The inhibition varies directly with the glucose calories in the intestine and averages 2.5 min/kcal. That these two results (0.4 kcal/min and 2.5 min/kcal) are reciprocals suggests a feedback inhibition on the gastric emptying of nutrients arising from beyond the pylorus and adequate to explain the rate of glucose delivery to the intestine. A control theory description of gastric emptying that includes such feedback regulation can be derived from these data to explain the different gastric emptying patterns of nutrients and nonnutrient solutions. These patterns give this visceral system a precision in its management of nutrients that can provide information crucial to preabsorptive satiety.

Assessment of gastric emptying in non-obese diabetic mice using a [13C]-octanoic acid breath test.

PubMed

Creedon, Christopher T; Verhulst, Pieter-Jan; Choi, Kyoung M; Mason, Jessica E; Linden, David R; Szurszewski, Joseph H; Gibbons, Simon J; Farrugia, Gianrico

2013-03-23

Gastric emptying studies in mice have been limited by the inability to follow gastric emptying changes in the same animal since the most commonly used techniques require killing of the animals and postmortem recovery of the meal(1,2). This approach prevents longitudinal studies to determine changes in gastric emptying with age and progression of disease. The commonly used [(13)C]-octanoic acid breath test for humans(3) has been modified for use in mice(4-6) and rats(7) and we previously showed that this test is reliable and responsive to changes in gastric emptying in response to drugs and during diabetic disease progression(8). In this video presentation the principle and practical implementation of this modified test is explained. As in the previous study, NOD LtJ mice are used, a model of type 1 diabetes(9). A proportion of these mice develop the symptoms of gastroparesis, a complication of diabetes characterized by delayed gastric emptying without mechanical obstruction of the stomach(10). This paper demonstrates how to train the mice for testing, how to prepare the test meal and obtain 4 hr gastric emptying data and how to analyze the obtained data. The carbon isotope analyzer used in the present study is suitable for the automatic sampling of the air samples from up to 12 mice at the same time. This technique allows the longitudinal follow-up of gastric emptying from larger groups of mice with diabetes or other long-standing diseases.

Pit Latrine Fecal Sludge Resistance Using a Dynamic Cone Penetrometer in Low Income Areas in Mzuzu City, Malawi

PubMed Central

Chirwa, Charles F. C.; Hall, Ralph P.; Krometis, Leigh-Anne H.; Vance, Eric A.; Edwards, Adam; Guan, Ting; Holm, Rochelle H.

2017-01-01

Pit latrines can provide improved household sanitation, but without effective and inexpensive emptying options, they are often abandoned once full and may pose a public health threat. Emptying techniques can be difficult, as the sludge contents of each pit latrine are different. The design of effective emptying techniques (e.g., pumps) is limited by a lack of data characterizing typical in situ latrine sludge resistance. This investigation aimed to better understand the community education and technical engineering needs necessary to improve pit latrine management. In low income areas within Mzuzu city, Malawi, 300 pit latrines from three distinct areas were assessed using a dynamic cone penetrometer to quantify fecal sludge strength, and household members were surveyed to determine their knowledge of desludging procedures and practices likely to impact fecal sludge characteristics. The results demonstrate that there is a significant difference in sludge strength between lined and unlined pits within a defined area, though sludge hardened with depth, regardless of the pit type or region. There was only limited association between cone penetration depth and household survey data. To promote the adoption of pit emptying, it is recommended that households be provided with information that supports pit emptying, such as latrine construction designs, local pit emptying options, and cost. This study indicates that the use of a penetrometer test in the field prior to pit latrine emptying may facilitate the selection of appropriate pit emptying technology. PMID:28165378

Delayed gastric emptying does not normalize after gluten withdrawal in adult celiac disease.

PubMed

Usai-Satta, Paolo; Oppia, Francesco; Scarpa, Mariella; Giannetti, Cristiana; Cabras, Francesco

2016-08-01

Objective Delayed gastric emptying has been frequently detected in patients with untreated celiac disease. According to several studies, gluten withdrawal showed to be effective in normalizing the gastric emptying rate. The aim of this study was to evaluate the gastric emptying rate of solids in patients with celiac disease before and after a gluten-free diet. Methods Twelve adult patients with celiac disease (age range 20-57 years) and 30 healthy controls (age range 30-54 years) underwent a (13)C-octanoic acid breath test to measure gastric emptying. Half emptying time (t1/2) and lag phase (tlag) were calculated. After at least 12 months of a gluten-free diet, celiac patients underwent a new (13)C-octanoic acid breath test. A symptom score was utilized to detect dyspeptic and malabsorption symptoms in all the patients. Results The gastric motility parameters, t1/2 and tlag, were significantly longer in patients than in controls. On a gluten-free diet, surprisingly, the gastric emptying did not normalize despite an improvement of symptom score. No significant correlation between abnormal gastric emptying and specific symptom patterns, anthropometric parameters or severity of histological damage was found. Conclusions This finding supports the hypothesis that gluten-driven mucosal inflammation might determine motor abnormalities by affecting smooth muscle contractility or impairing gut hormone function. The persistence of these abnormalities on a gluten free diet suggests the presence of a persistent low-grade mucosal inflammation with a permanent perturbation of the neuro-immunomodulatory regulation.

Validation of 13C-acetic acid breath test by measuring effects of loperamide, morphine, mosapride, and itopride on gastric emptying in mice.

PubMed

Matsumoto, Kenjiro; Kimura, Hiroshi; Tashima, Kimihito; Uchida, Masayuki; Horie, Syunji

2008-10-01

Several methods are used to evaluate gastric motility in rodents, but they all have technical limitations. Recent technical developments enable a convenient method to evaluate gastric motility. The (13)C-acetic acid breath test in rodents is a non-invasive and repeatable method that can be used without physical restraints. The present study aimed to validate the (13)C-acetic acid breath test by measuring the effects of loperamide, morphine, mosapride, and itopride on gastric emptying in mice. Loperamide (1-10 mg/kg) and morphine (1.25-10 mg/kg) slowed gastric emptying and decreased the maximum concentration (C(max)) and area under the curve (AUC(90 min)) value in a dose-dependent manner. Mosapride (0.2-5 mg/kg) accelerated gastric emptying and increased C(max) value. Mosapride (20 mg/kg) did not accelerate gastric emptying on the (13)C-breath test. Itopride (30 mg/kg, per os) significantly accelerated gastric emptying compared with the vehicle group. In a comparison with the conventional phenol red test, there was a correlation between the C(max) value of breath test and gastric emptying (%) of phenol red tests in treatment with loperamide or mosapride. These results indicate that the (13)C-acetic acid breath test is an accurate, noninvasive, and simple method for monitoring gastric emptying in mice. This method is useful to assess the effect of drugs and gut function pharmacologically.

The Wagner-Nelson method can generate an accurate gastric emptying flow curve from CO2 data obtained by a 13C-labeled substrate breath test.

PubMed

Sanaka, Masaki; Yamamoto, Takatsugu; Ishii, Tarou; Kuyama, Yasushi

2004-01-01

In pharmacokinetics, the Wagner-Nelson (W-N) method can accurately estimate the rate of drug absorption from its urinary elimination rate. A stable isotope (13C) breath test attempts to estimate the rate of absorption of 13C, as an index of gastric emptying rate, from the rate of pulmonary elimination of 13CO2. The time-gastric emptying curve determined by the breath test is quite different from that determined by scintigraphy or ultrasonography. In this report, we have shown that the W-N method can adjust the difference. The W-N equation to estimate gastric emptying from breath data is as follows: the fractional cumulative amount of gastric contents emptied by time t = Abreath (t)/Abreath (infinity) + (1/0.65).d[Abreath (t)/Abreath (infinity) ]/dt, where Abreath (t) = the cumulative recovery of 13CO2 in breath by time t and Abreath ( infinity ) = the ultimate cumulative 13CO2 recovery. The emptying flow curve generated by ultrasonography was compared with that generated by the W-N method-adjusted breath test in 6 volunteers. The emptying curves by the W-N method were almost identical to those by ultrasound. The W-N method can generate an accurate emptying flow curve from 13CO2 data, and it can adjust the difference between ultrasonography and the breath test. Copyright 2004 S. Karger AG, Basel

Characterization of limestone reacted with acid-mine drainage in a pulsed limestone bed treatment system at the Friendship Hill National Historical Site, Pennsylvania, USA

USGS Publications Warehouse

Hammarstrom, J.M.; Sibrell, P.L.; Belkin, H.E.

2003-01-01

Armoring of limestone is a common cause of failure in limestone-based acid-mine drainage (AMD) treatment systems. Limestone is the least expensive material available for acid neutralization, but is not typically recommended for highly acidic, Fe-rich waters due to armoring with Fe(III) oxyhydroxide coatings. A new AMD treatment technology that uses CO2 in a pulsed limestone bed reactor minimizes armor formation and enhances limestone reaction with AMD. Limestone was characterized before and after treatment with constant flow and with the new pulsed limestone bed process using AMD from an inactive coal mine in Pennsylvania (pH = 2.9, Fe = 150 mg/l, acidity = 1000 mg/l CaCO3). In constant flow experiments, limestone is completely armored with reddish-colored ochre within 48 h of contact in a fluidized bed reactor. Effluent pH initially increased from the inflow pH of 2.9 to over 7, but then decreased to 6 during operation. Limestone removed from a pulsed bed pilot plant is a mixture of unarmored, rounded and etched limestone grains and partially armored limestone and refractory mineral grains (dolomite, pyrite). The ???30% of the residual grains in the pulsed flow reactor that are armored have thicker (50- to 100-??m), more aluminous coatings and lack the gypsum rind that develops in the constant flow experiment. Aluminium-rich zones developed in the interior parts of armor rims in both the constant flow and pulsed limestone bed experiments in response to pH changes at the solid/solution interface. ?? 2003 Elsevier Ltd. All rights reserved.

Distinct Element Method modelling of fold-related fractures in a multilayer sequence

NASA Astrophysics Data System (ADS)

Kaserer, Klemens; Schöpfer, Martin P. J.; Grasemann, Bernhard

2017-04-01

Natural fractures have a significant impact on the performance of hydrocarbon systems/reservoirs. In a multilayer sequence, both the fracture density within the individual layers and the type of fracture intersection with bedding contacts are key parameters controlling fluid pathways. In the present study the influence of layer stacking and interlayer friction on fracture density and connectivity within a folded sequence is systematically investigated using 2D Distinct Element Method modelling. Our numerical approach permits forward modelling of both fracture nucleation/propagation/arrest and (contemporaneous) frictional slip along bedding planes in a robust and mechanically sound manner. Folding of the multilayer sequence is achieved by enforcing constant curvature folding by means of a velocity boundary condition at the model base, while a constant overburden pressure is maintained at the model top. The modelling reveals that with high bedding plane friction the multilayer stack behaves mechanically as a single layer so that the neutral surface develops in centre of the sequence and fracture spacing is controlled by the total thickness of the folded sequence. In contrast, low bedding plane friction leads to decoupling of the individual layers (flexural slip folding) so that a neutral surface develops in the centre of each layer and fracture spacing is controlled by the thickness of the individual layers. The low interfacial friction models illustrate that stepping of fractures across bedding planes is a common process, which can however have two contrasting origins: The mechanical properties of the interface cause fracture stepping during fracture propagation. Originally through-going fractures are later offset by interfacial slip during folding. A combination of these two different origins may lead to (apparently) inconsistent fracture offsets across bedding planes within a flexural slip fold.

Differences in fundamental and functional properties of HPMC co-processed fillers prepared by fluid-bed coating and spray drying.

PubMed

Dong, QianQian; Zhou, MiaoMiao; Lin, Xiao; Shen, Lan; Feng, Yi

2018-07-01

This study aimed to develop novel co-processed tablet fillers based on the principle of particle engineering for direct compaction and to compare the characteristics of co-processed products obtained by fluid-bed coating and co-spray drying, respectively. Water-soluble mannitol and water-insoluble calcium carbonate were selected as representative fillers for this study. Hydroxypropyl methylcellulose (HPMC), serving as a surface property modifier, was distributed on the surface of primary filler particles via the two co-processing methods. Both fundamental and functional properties of the products were comparatively investigated. The results showed that functional properties of the fillers, like flowability, compactibility, and drug-loading capacity, were effectively improved by both co-processing methods. However, fluid-bed coating showed greater advantages over co-spray drying in some aspects, which was mainly attributed to the remarkable differences in some fundamental properties of co-processed powders, like particle size, surface topology, and particle structure. For example, the more irregular surface and porous structure induced by fluid-bed coating could contribute to better compaction properties and lower lubricant sensitivity due to the increasing contact area and mechanical interlocking between particles under pressure. More effective surface distribution of HPMC during fluid-bed coating was also a contributor. In addition, such a porous agglomerate structure could also reduce the separation of drug and excipients after mixing, resulting in the improvement in drug loading capacity and tablet uniformity. In summary, fluid-bed coating appears to be more promising for co-processing than spray drying in some aspects, and co-processed excipients produced by it have a great prospect for further investigations and development. Copyright © 2018 Elsevier B.V. All rights reserved.

49 CFR 173.428 - Empty Class 7 (radioactive) materials packaging.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Empty Class 7 (radioactive) materials packaging... SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.428 Empty Class 7 (radioactive) materials packaging. A packaging which previously contained Class 7 (radioactive...

Optimization of the Negative Electrode in Organic Photovoltaic Devices

NASA Astrophysics Data System (ADS)

Reese, Matthew; White, Matthew; Rumbles, Garry; Ginley, David; Shaheen, Sean

2007-03-01

A blend of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C61-butyric acid methyl ester (PCBM) is used as the active layer in a series of bulk heterojunction organic solar cells. This polymer blend serves as a test-bed to explore the significant effects on device performance of using low work function metals and/or alkali metal halides as the top, negative electrode. Work function values reported in the literature are compared with those measured for our thin films. A series of contact materials are investigated including Al, Ca/Al, Ba/Al, LiF/Al; many devices are prepared with each contact type to validate the statistical significance of the results.

Contact structure for use in catalytic distillation

DOEpatents

Jones, Jr., Edward M.

1984-01-01

A method for conducting catalytic chemical reactions and fractionation of the reaction mixture comprising feeding reactants into a distillation column reactor contracting said reactant in liquid phase with a fixed bed catalyst in the form of a contact catalyst structure consisting of closed porous containers containing the catatlyst for the reaction and a clip means to hold and support said containers, which are disposed above, i.e., on the distillation trays in the tower. The trays have weir means to provide a liquid level on the trays to substantially cover the containers. In other words, the trays function in their ordinary manner with the addition thereto of the catalyst. The reaction mixture is concurrently fractionated in the column.

Apparatus and method for solar coal gasification

DOEpatents

Gregg, David W.

1980-01-01

Apparatus for using focused solar radiation to gasify coal and other carbonaceous materials. Incident solar radiation is focused from an array of heliostats onto a tower-mounted secondary mirror which redirects the focused solar radiation down through a window onto the surface of a vertically-moving bed of coal, or a fluidized bed of coal, contained within a gasification reactor. The reactor is designed to minimize contact between the window and solids in the reactor. Steam introduced into the gasification reactor reacts with the heated coal to produce gas consisting mainly of carbon monoxide and hydrogen, commonly called "synthesis gas", which can be converted to methane, methanol, gasoline, and other useful products. One of the novel features of the invention is the generation of process steam at the rear surface of the secondary mirror.

Apparatus for solar coal gasification

DOEpatents

Gregg, D.W.

Apparatus for using focused solar radiation to gasify coal and other carbonaceous materials is described. Incident solar radiation is focused from an array of heliostats onto a tower-mounted secondary mirror which redirects the focused solar radiation down through a window onto the surface of a vertically-moving bed of coal, or a fluidized bed of coal, contained within a gasification reactor. The reactor is designed to minimize contact between the window and solids in the reactor. Steam introduced into the gasification reactor reacts with the heated coal to produce gas consisting mainly of carbon monoxide and hydrogen, commonly called synthesis gas, which can be converted to methane, methanol, gasoline, and other useful products. One of the novel features of the invention is the generation of process steam at the rear surface of the secondary mirror.

Alkylation of organic aromatic compounds

DOEpatents

Smith, L.A. Jr.; Arganbright, R.P.; Hearn, D.

1993-09-07

Aromatic compounds are alkylated in a catalytic distillation, wherein the catalyst structure also serves as a distillation component by contacting the aromatic compound with a C[sub 2] to C[sub 10] olefin in the catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 80 C to 500 C, using as the catalyst a molecular sieve characterized as acidic or an acidic cation exchange resin. For example, ethyl benzene is produced by feeding ethylene to about the mid point of the catalyst bed while benzene is conveniently added through the reflux in molar excess to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene in the bottoms. 1 figures.

Alkylation of organic aromatic compounds

DOEpatents

Smith, Jr., Lawrence A.; Arganbright, Robert P.; Hearn, Dennis

1993-01-01

Aromatic compounds are alkylated in a catalytic distillation, wherein the catalyst structure also serves as a distillation component by contacting the aromatic compound with a C.sub.2 to C.sub.10 olefin in the catalyst bed under 0.25 to 50 atmospheres of pressure and at temperatures in the range of 80.degree. C. to 500.degree. C., using as the catalyst a mole sieve characterized as acidic or an acidic cation exchange resin. For example, ethyl benzene is produced by feeding ethylene to about the mid point of the catalyst bed while benzene is conveniently added through the reflux in molar excess to that required to react with ethylene, thereby reacting substantially all of the ethylene and recovering benzene as the principal overhead and ethyl benzene in the bottoms.

A contact-free respiration monitor for smart bed and ambulatory monitoring applications.

PubMed

Hart, Adam; Tallevi, Kevin; Wickland, David; Kearney, Robert E; Cafazzo, Joseph A

2010-01-01

The development of a contact-free respiration monitor has a broad range of clinical applications in the home and hospital setting. Current approaches suffer from a variety of problems including unreliability, low sensitivity, and high cost. This work describes a novel approach to contact-free respiration monitoring that addresses these shortcomings by employing a highly sensitive capacitance sensor to detect variations in capacitive coupling caused by breathing. A prototype system consisting of a synthetic-metallic pad, sensor electronics, and iPhone interface was built and its performance compared experimentally to the gold standard technique (Respiratory Inductance Plethysmography) on both a healthy volunteer and SimMan robotic mannequin. The prototype sensor effectively captured respiratory movements over breathing rates of 5-55 bpm; achieving an average spectral correlation of 0.88 (CI: 0.86-0.90) and 0.95 (CI: 0.95-0.96) to the gold standard using the SimMan and healthy volunteer respectively.

Contact dynamics math model

NASA Technical Reports Server (NTRS)

Glaese, John R.; Tobbe, Patrick A.

1986-01-01

The Space Station Mechanism Test Bed consists of a hydraulically driven, computer controlled six degree of freedom (DOF) motion system with which docking, berthing, and other mechanisms can be evaluated. Measured contact forces and moments are provided to the simulation host computer to enable representation of orbital contact dynamics. This report describes the development of a generalized math model which represents the relative motion between two rigid orbiting vehicles. The model allows motion in six DOF for each body, with no vehicle size limitation. The rotational and translational equations of motion are derived. The method used to transform the forces and moments from the sensor location to the vehicles' centers of mass is also explained. Two math models of docking mechanisms, a simple translational spring and the Remote Manipulator System end effector, are presented along with simulation results. The translational spring model is used in an attempt to verify the simulation with compensated hardware in the loop results.

Thermal release of D2 from new Be-D co-deposits on previously baked co-deposits

NASA Astrophysics Data System (ADS)

Baldwin, M. J.; Doerner, R. P.

2015-12-01

Past experiments and modeling with the TMAP code in [1, 2] indicated that Be-D co-deposited layers are less (time-wise) efficiently desorbed of retained D in a fixed low-temperature bake, as the layer grows in thickness. In ITER, beryllium rich co-deposited layers will grow in thickness over the life of the machine. Although, compared with the analyses in [1, 2], ITER presents a slightly different bake efficiency problem because of instances of prior tritium recover/control baking. More relevant to ITER, is the thermal release from a new and saturated co-deposit layer in contact with a thickness of previously-baked, less-saturated, co-deposit. Experiments that examine the desorption of saturated co-deposited over-layers in contact with previously baked under-layers are reported and comparison is made to layers of the same combined thickness. Deposition temperatures of ∼323 K and ∼373 K are explored. It is found that an instance of prior bake leads to a subtle effect on the under-layer. The effect causes the thermal desorption of the new saturated over-layer to deviate from the prediction of the validated TMAP model in [2]. Instead of the D thermal release reflecting the combined thickness and levels of D saturation in the over and under layer, experiment differs in that, i) the desorption is a fractional superposition of desorption from the saturated over-layer, with ii) that of the combined over and under -layer thickness. The result is not easily modeled by TMAP without the incorporation of a thin BeO inter-layer which is confirmed experimentally on baked Be-D co-deposits using X-ray micro-analysis.

Communication strategies and timeliness of response to life critical telemetry alarms.

PubMed

Bonzheim, Kimberly A; Gebara, Rani I; O'Hare, Bridget M; Ellis, R Darin; Brand, Monique A; Balar, Salil D; Stockman, Rita; Sciberras, Annette M; Haines, David E

2011-05-01

A centralized electrocardiogram telemetry monitoring system (TMS) facilitates early identification of critical arrhythmias and acute medical decompensation. Timely intervention can only be performed if abnormalities are communicated rapidly to the direct caregiver. The study objectives were to measure effectiveness of bi-directional voice communication badges versus one-way alphanumeric pagers for telemetry alarm response and communication loop closure. A sequential observational pilot study of nursing response to TMS alarms compared communication technologies on four nursing units in a 1,061 bed tertiary care hospital with 264 TMS channels of telemetry over a 2-year period. Subsequently, the communication technologies were compared in a randomized fashion on a 68-bed progressive cardiac care unit. Caregivers were blinded to the protocol. All alarm responses were recorded during two periods using either pagers or voice communication devices. Alarm response time and closure of the communication loop were analyzed in a blinded fashion. The direct communication functionality of the badge significantly shortened the time to first contact, time to completion, and rate of closure of the communication loop in both the pilot and study phases. Median time to first contact with the communication badge was 0.5  min, compared to 1.6  min with pager communication (p < 0.0003). Communication loop closure was achieved in 100% of clinical alarms using the badge versus 19% with the pager (p < 0.0001). Communication badge technology reduced alarm time to first contact and completion as well as facilitated communication loop closures. Immediate two-way communication significantly impacted practice, alarm management, and resulted in faster bedside care.

27 CFR 25.36 - Empty container storage.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Empty container storage. 25.36 Section 25.36 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY ALCOHOL BEER Construction and Equipment Equipment § 25.36 Empty container storage...

27 CFR 25.36 - Empty container storage.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Empty container storage. 25.36 Section 25.36 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Construction and Equipment Equipment § 25.36 Empty container storage...

27 CFR 25.36 - Empty container storage.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Empty container storage. 25.36 Section 25.36 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Construction and Equipment Equipment § 25.36 Empty container storage...

27 CFR 25.36 - Empty container storage.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Empty container storage. 25.36 Section 25.36 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Construction and Equipment Equipment § 25.36 Empty container storage...

14 CFR 29.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Empty weight and corresponding center of gravity. 29.29 Section 29.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must...

14 CFR 27.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Empty weight and corresponding center of gravity. 27.29 Section 27.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 27.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Empty weight and corresponding center of gravity. 27.29 Section 27.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 23.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... gravity. 23.29 Section 23.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Flight General § 23.29 Empty weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be determined by weighing the airplane with— (1) Fixed ballast; (2...

14 CFR 27.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Empty weight and corresponding center of gravity. 27.29 Section 27.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 25.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Empty weight and corresponding center of gravity. 25.29 Section 25.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 25.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Empty weight and corresponding center of gravity. 25.29 Section 25.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 29.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Empty weight and corresponding center of gravity. 29.29 Section 29.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must...

14 CFR 23.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... gravity. 23.29 Section 23.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Flight General § 23.29 Empty weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be determined by weighing the airplane with— (1) Fixed ballast; (2...

14 CFR 29.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Empty weight and corresponding center of gravity. 29.29 Section 29.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must...

14 CFR 25.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Empty weight and corresponding center of gravity. 25.29 Section 25.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 27.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Empty weight and corresponding center of gravity. 27.29 Section 27.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 29.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Empty weight and corresponding center of gravity. 29.29 Section 29.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must...

14 CFR 27.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Empty weight and corresponding center of gravity. 27.29 Section 27.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 29.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Empty weight and corresponding center of gravity. 29.29 Section 29.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must...

14 CFR 25.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Empty weight and corresponding center of gravity. 25.29 Section 25.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 23.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... gravity. 23.29 Section 23.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Flight General § 23.29 Empty weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be determined by weighing the airplane with— (1) Fixed ballast; (2...

14 CFR 23.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... gravity. 23.29 Section 23.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Flight General § 23.29 Empty weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be determined by weighing the airplane with— (1) Fixed ballast; (2...

14 CFR 25.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Empty weight and corresponding center of gravity. 25.29 Section 25.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be...

14 CFR 23.29 - Empty weight and corresponding center of gravity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... gravity. 23.29 Section 23.29 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Flight General § 23.29 Empty weight and corresponding center of gravity. (a) The empty weight and corresponding center of gravity must be determined by weighing the airplane with— (1) Fixed ballast; (2...

Spherical nanocrystalline cellulose (NCC) from oil palm empty fruit bunch pulp via ultrasound assisted hydrolysis.

PubMed

Zianor Azrina, Z A; Beg, M Dalour H; Rosli, M Y; Ramli, Ridzuan; Junadi, Norhafzan; Alam, A K M Moshiul

2017-04-15

Nanocrystalline cellulose (NCC) was isolated from oil palm empty fruit bunch pulp (EFBP) using ultrasound assisted acid hydrolysis. The obtained NCC was analysed using FESEM, XRD, FTIR, and TGA, and compared with raw empty fruit bunch fibre (REFB), empty fruit bunch pulp (EFBP), and treated empty fruit bunch pulp (TEFBP). Based on FESEM analysis, it was found that NCC has a spherical shaped after acid hydrolysis with the assistance of ultrasound. This situation was different compared to previous studies that obtained rod-like shaped of NCC. Furthermore, the crystallinity of NCC is higher compared to REFB and EFBP. According to thermal stability, the NCC obtained shows remarkable sign of high thermal stability compared to REFB and EFBP. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of Jiangzhi tablet on gastrointestinal propulsive function in mice

NASA Astrophysics Data System (ADS)

Wang, Xiangrong; Geng, Xiuli; Zhao, Jingsheng; Fan, Lili; Zhang, Zhengchen

2018-04-01

This paper aims to study the effect of lipid-lowering tablets on gastric emptying and small intestinal propulsion in mice. Mice were randomly divided into control group, Digestant Pill group, Jiangzhi tablet group, middle dose and small dose, the mice gastric emptying phenolsulfonphthalein, gastric residual rate of phenol red indicator to evaluate the gastric emptying rate, residual rate of detection in mouse stomach; small intestine propulsion and selection of carbon ink as the experimental index. Effects were observed to promote the function of normal mice gastric emptying and intestine. The gastric emptying and small intestinal motor function of normal mice were all promoted by each administration group, and the effect was most obvious in small dose group. The effect of reducing blood lipid on gastrointestinal motility of mice ware obviously enhanced.

Effects of empty bins on image upscaling in capsule endoscopy

NASA Astrophysics Data System (ADS)

Rukundo, Olivier

2017-07-01

This paper presents a preliminary study of the effect of empty bins on image upscaling in capsule endoscopy. The presented study was conducted based on results of existing contrast enhancement and interpolation methods. A low contrast enhancement method based on pixels consecutiveness and modified bilinear weighting scheme has been developed to distinguish between necessary empty bins and unnecessary empty bins in the effort to minimize the number of empty bins in the input image, before further processing. Linear interpolation methods have been used for upscaling input images with stretched histograms. Upscaling error differences and similarity indices between pairs of interpolation methods have been quantified using the mean squared error and feature similarity index techniques. Simulation results demonstrated more promising effects using the developed method than other contrast enhancement methods mentioned.

Pit Latrine Emptying Behavior and Demand for Sanitation Services in Dar Es Salaam, Tanzania

PubMed Central

Jenkins, Marion W.; Cumming, Oliver; Cairncross, Sandy

2015-01-01

Pit latrines are the main form of sanitation in unplanned areas in many rapidly growing developing cities. Understanding demand for pit latrine fecal sludge management (FSM) services in these communities is important for designing demand-responsive sanitation services and policies to improve public health. We examine latrine emptying knowledge, attitudes, behavior, trends and rates of safe/unsafe emptying, and measure demand for a new hygienic latrine emptying service in unplanned communities in Dar Es Salaam (Dar), Tanzania, using data from a cross-sectional survey at 662 residential properties in 35 unplanned sub-wards across Dar, where 97% had pit latrines. A picture emerges of expensive and poor FSM service options for latrine owners, resulting in widespread fecal sludge exposure that is likely to increase unless addressed. Households delay emptying as long as possible, use full pits beyond what is safe, face high costs even for unhygienic emptying, and resort to unsafe practices like ‘flooding out’. We measured strong interest in and willingness to pay (WTP) for the new pit emptying service at 96% of residences; 57% were WTP ≥U.S. $17 to remove ≥200 L of sludge. Emerging policy recommendations for safe FSM in unplanned urban communities in Dar and elsewhere are discussed. PMID:25734790

A gamma variate model that includes stretched exponential is a better fit for gastric emptying data from mice

PubMed Central

Bajzer, Željko; Gibbons, Simon J.; Coleman, Heidi D.; Linden, David R.

2015-01-01

Noninvasive breath tests for gastric emptying are important techniques for understanding the changes in gastric motility that occur in disease or in response to drugs. Mice are often used as an animal model; however, the gamma variate model currently used for data analysis does not always fit the data appropriately. The aim of this study was to determine appropriate mathematical models to better fit mouse gastric emptying data including when two peaks are present in the gastric emptying curve. We fitted 175 gastric emptying data sets with two standard models (gamma variate and power exponential), with a gamma variate model that includes stretched exponential and with a proposed two-component model. The appropriateness of the fit was assessed by the Akaike Information Criterion. We found that extension of the gamma variate model to include a stretched exponential improves the fit, which allows for a better estimation of T1/2 and Tlag. When two distinct peaks in gastric emptying are present, a two-component model is required for the most appropriate fit. We conclude that use of a stretched exponential gamma variate model and when appropriate a two-component model will result in a better estimate of physiologically relevant parameters when analyzing mouse gastric emptying data. PMID:26045615

Exploring gastric emptying rate in minipigs: Effect of food type and pre-dosing of metoclopramide.

PubMed

Henze, Laura J; Griffin, Brendan T; Christiansen, Martin; Bundgaard, Christoffer; Langguth, Peter; Holm, René

2018-06-15

The present study investigated the gastric emptying rate in Göttingen minipigs pre- and post-prandial and evaluated the effect of metoclopramide on the same parameter, using paracetamol as an absorption marker. The pharmacokinetic evaluation of the obtained plasma concentration data for paracetamol demonstrated that the fastest gastric emptying rate was observed in the animals that were allowed access to normal pig food. There was no significant difference in the stomach emptying rate observed between fasted and fed minipigs, when fed either with a FDA standard breakfast or a nutritional energy drink. Pre-dosing minipigs with metoclopramide (0.2 or 0.4 mg/kg) did not demonstrate any effect on gastric emptying in either the fasted or fed state. The data in the present study demonstrated a relatively prolonged gastric emptying rate in mini-pigs both in the fasted and fed state, hence when conducting pharmacokinetic studies using minipigs, this should be taken into account when planning the plasma sampling time points. Further, as no difference could be observed in gastric emptying rate as a function of food, the data also suggest that the Göttingen mini-pigs seems less suited to predict for food effect studies than other species. Copyright © 2018 Elsevier B.V. All rights reserved.

The effects of consuming carbohydrate-electrolyte beverages on gastric emptying and fluid absorption during and following exercise.

PubMed

Murray, R

1987-01-01

A variety of beverages formulated to provide fluid, carbohydrates, and electrolytes during and following exercise are commercially available. Such 'sport drinks' commonly contain 4 to 8% carbohydrate (as glucose, fructose, sucrose or maltodextrins) and small amounts of electrolytes (most often sodium, potassium, and chloride). The efficacy of consuming such beverages has been questioned primarily because of concern that beverage carbohydrate content may inhibit gastric emptying rate and fluid absorption during exercise, thereby jeopardizing physiological homeostasis and impairing exercise performance. Gastric motor activity, and consequently gastric emptying rate, is governed by neural and humoral feedback provided by receptors found in the gastric musculature and proximal small intestine. Gastric emptying rate may be influenced by a variety of factors including, but not limited to, the caloric content, volume, osmolality, temperature, and pH of the ingested fluid, diurnal and interindividual variation, metabolic state (rest/exercise), and the ambient temperature. The caloric content of the ingested fluid appears to be the most important variable governing gastric emptying rate, providing a mean caloric efflux from the stomach of 2.0 to 2.5 kcal/min for ingested fluid volumes less than 400 ml. At rest, gastric emptying is inhibited by solutions containing calories in a manner independent of the nutrient source (i.e. carbohydrate, fat or protein). Consequently, plain water is known to empty from the stomachs of resting subjects at rates faster than solutions containing calories. Gastric emptying is increasingly inhibited as the caloric content of the ingested fluid increases. During moderate exercise (less than 75% VO2max), gastric emptying occurs at a rate similar to that during rest; more intense exercise appears to inhibit gastric emptying. When fluids are consumed at regular intervals throughout prolonged exercise (greater than 2 hours), postexercise aspiration of stomach contents reveals that solutions containing up to 10% carbohydrate empty at rates similar to plain water. There is ample physiological justification for the addition of glucose, fructose, sodium, potassium and chloride to fluid replacement beverages. Fluid absorption in the small intestine is stimulated by glucose and sodium (and to a lesser extent by fructose and other electrolytes). Glucose and sodium are absorbed via a common membrane carrier in the mucosal epithelium of the proximal small intestine. The potentiation of sodium uptake by glucose establishes an osmotic gradient for fluid absorption.(ABSTRACT TRUNCATED AT 400 WORDS)

Contrast-Enhanced Magnetic Resonance Imaging of Gastric Emptying and Motility in Rats.

PubMed

Lu, Kun-Han; Cao, Jiayue; Oleson, Steven Thomas; Powley, Terry L; Liu, Zhongming

2017-11-01

The assessment of gastric emptying and motility in humans and animals typically requires radioactive imaging or invasive measurements. Here, we developed a robust strategy to image and characterize gastric emptying and motility in rats based on contrast-enhanced magnetic resonance imaging (MRI) and computer-assisted image processing. The animals were trained to naturally consume a gadolinium-labeled dietgel while bypassing any need for oral gavage. Following this test meal, the animals were scanned under low-dose anesthesia for high-resolution T1-weighted MRI in 7 Tesla, visualizing the time-varying distribution of the meal with greatly enhanced contrast against non-gastrointestinal (GI) tissues. Such contrast-enhanced images not only depicted the gastric anatomy, but also captured and quantified stomach emptying, intestinal filling, antral contraction, and intestinal absorption with fully automated image processing. Over four postingestion hours, the stomach emptied by 27%, largely attributed to the emptying of the forestomach rather than the corpus and the antrum, and most notable during the first 30 min. Stomach emptying was accompanied by intestinal filling for the first 2 h, whereas afterward intestinal absorption was observable as cumulative contrast enhancement in the renal medulla. The antral contraction was captured as a peristaltic wave propagating from the proximal to distal antrum. The frequency, velocity, and amplitude of the antral contraction were on average 6.34 ± 0.07 contractions per minute, 0.67 ± 0.01 mm/s, and 30.58 ± 1.03%, respectively. These results demonstrate an optimized MRI-based strategy to assess gastric emptying and motility in healthy rats, paving the way for using this technique to understand GI diseases, or test new therapeutics in rat models.The assessment of gastric emptying and motility in humans and animals typically requires radioactive imaging or invasive measurements. Here, we developed a robust strategy to image and characterize gastric emptying and motility in rats based on contrast-enhanced magnetic resonance imaging (MRI) and computer-assisted image processing. The animals were trained to naturally consume a gadolinium-labeled dietgel while bypassing any need for oral gavage. Following this test meal, the animals were scanned under low-dose anesthesia for high-resolution T1-weighted MRI in 7 Tesla, visualizing the time-varying distribution of the meal with greatly enhanced contrast against non-gastrointestinal (GI) tissues. Such contrast-enhanced images not only depicted the gastric anatomy, but also captured and quantified stomach emptying, intestinal filling, antral contraction, and intestinal absorption with fully automated image processing. Over four postingestion hours, the stomach emptied by 27%, largely attributed to the emptying of the forestomach rather than the corpus and the antrum, and most notable during the first 30 min. Stomach emptying was accompanied by intestinal filling for the first 2 h, whereas afterward intestinal absorption was observable as cumulative contrast enhancement in the renal medulla. The antral contraction was captured as a peristaltic wave propagating from the proximal to distal antrum. The frequency, velocity, and amplitude of the antral contraction were on average 6.34 ± 0.07 contractions per minute, 0.67 ± 0.01 mm/s, and 30.58 ± 1.03%, respectively. These results demonstrate an optimized MRI-based strategy to assess gastric emptying and motility in healthy rats, paving the way for using this technique to understand GI diseases, or test new therapeutics in rat models.

Application of multiwalled carbon nanotubes and its magnetite derivative for emulsified oil removal from produced water.

PubMed

Ibrahim, Taleb H; Sabri, Muhammad A; Khamis, Mustafa I

2018-05-10

Multiwalled carbon nanotubes and their magnetite derivatives were employed as adsorbents for emulsified oil removal from produced water. The experimental parameters for maximum emulsified oil removal efficiency and effective regeneration of these adsorbents were determined. The optimum parameters in terms of adsorbent dosage, contact time, salinity, pH and temperature were 3.0 g/L, 20.0 min, 0 ppm, 7.0 and 25°C for both adsorbents. Due to their low density, multiwalledcarbon nanotubes could not be successfully employed in packed bed columns. The magnetite derivative has a larger density and hence, for the removal of emulsified oil from produced water packed bed column studies were performed utilizing multiwalled carbon magnetite nanotubes. The packed bed column efficiency and behaviour were evaluated using Thomas, Clark, Yan et al. and Bohart and Adams models. The Yan model was found to best describe the column experimental data. The adsorbents were regenerated using n-hexane and reused several times for oil removal from produced water without any significant decrease in their initial adsorption capacities.

Mesoscale simulations of shock compaction of a granular ceramic: effects of mesostructure and mixed-cell strength treatment

NASA Astrophysics Data System (ADS)

Derrick, J. G.; LaJeunesse, J. W.; Davison, T. M.; Borg, J. P.; Collins, G. S.

2018-04-01

The shock response of granular materials is important in a variety of contexts but the precise dynamics of grains during compaction is poorly understood. Here we use 2D mesoscale numerical simulations of the shock compaction of granular tungsten carbide to investigate the effect of internal structure within the particle bed and ‘stiction’ between grains on the shock response. An increase in the average number of contacts with other particles, per particle, tends to shift the Hugoniot to higher shock velocities, lower particle velocities and lower densities. This shift is sensitive to inter-particle shear resistance. Eulerian shock physics codes approximate friction between, and interlocking of, grains with their treatment of mixed cell strength (stiction) and here we show that this has a significant effect on the shock response. When studying the compaction of particle beds it is not common to quantify the pre-compaction internal structure, yet our results suggest that such differences should be taken into account, either by using identical beds or by averaging results over multiple experiments.

Co-pyrolysis behaviors of saw dust and Shenfu coal in drop tube furnace and fixed bed reactor.

PubMed

Li, Shuaidan; Chen, Xueli; Wang, Li; Liu, Aibin; Yu, Guangsuo

2013-11-01

Co-pyrolysis behaviors of saw dust (SD) and Shenfu bituminous coal (SF) were studied in a drop tube furnace and a fixed bed reactor at different temperatures respectively. Six different biomass/coal ratios (B:C) were used. Compared the results with the calculated value obtained by the additional behavior, CO volume yields were lower while H2, CH4, CO2, volume yields were higher. Blend char yields had a good agreement with the calculated values, and their structures remained similar with SD and SF char's. Synergy effect occurred in gaseous phase, which was mainly caused by the secondary reactions. Compared the blend char yields in the drop tube furnace with those in the fixed bed reactor, the results showed the contacting way of biomass and coal particles had little influence on char yield in co-pyrolysis process. The reactivity index of blend char achieved the minimum at B:C=40:60 and the maximum at B:C=80:20. Copyright © 2013 Elsevier Ltd. All rights reserved.

Expedited patient-specific assessment of contact stress exposure in the ankle joint following definitive articular fracture reduction.

PubMed

Kern, Andrew M; Anderson, Donald D

2015-09-18

Acute injury severity, altered joint kinematics, and joint incongruity are three important mechanical factors linked to post-traumatic osteoarthritis (PTOA). Finite element analysis (FEA) was previously used to assess the influence of increased contact stress due to joint incongruity on PTOA development. While promising agreement with PTOA development was seen, the inherent complexities of contact FEA limited the numbers of subjects that could be analyzed. Discrete element analysis (DEA) is a simplified methodology for contact stress computation, which idealizes contact surfaces as a bed of independent linear springs. In this study, DEA was explored as an expedited alternative to FEA contact stress exposure computation. DEA was compared to FEA using results from a previously completed validation study of two cadaveric human ankles, as well as a previous study of post-operative contact stress exposure in 11 patients with tibial plafond fracture. DEA-computed maximum contact stresses were within 19% of those experimentally measured, with 90% of the contact area having computed contact stress values within 1MPa of those measured. In the 11 fractured ankles, maximum contact stress and contact area differences between DEA and FEA were 0.85 ± 0.64 MPa and 22.5 ± 11.5mm(2). As a predictive measure for PTOA development, both DEA and FEA had 100% concordance with presence of OA (KL grade ≥ 2) and >95% concordance with KL grade at 2 years. These results support DEA as a reasonable alternative to FEA for computing contact stress exposures following surgical reduction of a tibial plafond fracture. Copyright © 2015 Elsevier Ltd. All rights reserved.

The addition of locust bean gum but not water delayed the gastric emptying rate of a nutrient semisolid meal in healthy subjects

PubMed Central

Darwiche, Gassan; Björgell, Ola; Almér, Lars-olof

2003-01-01

Background Most of the previous studies regarding the effects of gel-forming fibres have considered the gastric emptying of liquid or solid meals after the addition of pectin or guar gum. The influence of locust bean gum, on gastric emptying of nutrient semisolid meals in humans has been less well studied, despite its common occurrence in foods. Using a standardised ultrasound method, this study was aimed at investigating if the gastric emptying in healthy subjects could be influenced by adding locust been gum, a widely used thickening agent, or water directly into a nutrient semisolid test meal. Methods The viscosity of a basic test meal (300 g rice pudding, 330 kcal) was increased by adding Nestargel (6 g, 2.4 kcal), containing viscous dietary fibres (96.5%) provided as seed flour of locust bean gum, and decreased by adding 100 ml of water. Gastric emptying of these three test meals were evaluated in fifteen healthy non-smoking volunteers, using ultrasound measurements of the gastric antral area to estimate the gastric emptying rate (GER). Results The median value of GER with the basic test meal (rice pudding) was estimated at 63 %, (range 47 to 84 %), (the first quartile = 61 %, the third quartile = 69 %). Increasing the viscosity of the rice pudding by adding Nestargel, resulted in significantly lower gastric emptying rates (p < 0.01), median GER 54 %, (range 7 to 71 %), (the first quartile = 48 %, the third quartile = 60 %). When the viscosity of the rice pudding was decreased (basic test meal added with water), the difference in median GER 65 %, (range 38 to 79 %), (the first quartile = 56 %, the third quartile = 71 %) was not significantly different (p = 0.28) compared to the GER of the basic test meal. Conclusions We conclude that the addition of locust bean gum to a nutrient semisolid meal has a major impact on gastric emptying by delaying the emptying rate, but that the addition of water to this test meal has no influence on gastric emptying in healthy subjects. PMID:12793910

The addition of locust bean gum but not water delayed the gastric emptying rate of a nutrient semisolid meal in healthy subjects.

PubMed

Darwiche, Gassan; Björgell, Ola; Almér, Lars-Olof

2003-06-06

Most of the previous studies regarding the effects of gel-forming fibres have considered the gastric emptying of liquid or solid meals after the addition of pectin or guar gum. The influence of locust bean gum, on gastric emptying of nutrient semisolid meals in humans has been less well studied, despite its common occurrence in foods. Using a standardised ultrasound method, this study was aimed at investigating if the gastric emptying in healthy subjects could be influenced by adding locust been gum, a widely used thickening agent, or water directly into a nutrient semisolid test meal. The viscosity of a basic test meal (300 g rice pudding, 330 kcal) was increased by adding Nestargel (6 g, 2.4 kcal), containing viscous dietary fibres (96.5%) provided as seed flour of locust bean gum, and decreased by adding 100 ml of water. Gastric emptying of these three test meals were evaluated in fifteen healthy non-smoking volunteers, using ultrasound measurements of the gastric antral area to estimate the gastric emptying rate (GER). The median value of GER with the basic test meal (rice pudding) was estimated at 63%, (range 47 to 84%), (the first quartile = 61%, the third quartile = 69%). Increasing the viscosity of the rice pudding by adding Nestargel, resulted in significantly lower gastric emptying rates (p < 0.01), median GER 54%, (range 7 to 71%), (the first quartile = 48%, the third quartile = 60%). When the viscosity of the rice pudding was decreased (basic test meal added with water), the difference in median GER 65%, (range 38 to 79%), (the first quartile = 56%, the third quartile = 71%) was not significantly different (p = 0.28) compared to the GER of the basic test meal. We conclude that the addition of locust bean gum to a nutrient semisolid meal has a major impact on gastric emptying by delaying the emptying rate, but that the addition of water to this test meal has no influence on gastric emptying in healthy subjects.

Determination of solid- and liquid-phase gastric emptying half times in cats by use of nuclear scintigraphy.

PubMed

Costello, M; Papasouliotis, K; Barr, F J; Gruffydd-Jones, T J; Caney, S M

1999-10-01

To use nuclear scintigraphy to establish a range of gastric emptying half times (t1/2) following a liquid or solid meal in nonsedated cats. 12 clinically normal 3-year-old domestic shorthair cats. A test meal of 75 g of scrambled eggs labeled with technetium Tc 99m tin colloid was fed to 10 of the cats, and solid-phase gastric emptying t1/2 were determined by use of nuclear scintigraphy. In a separate experiment, 8 of these cats plus an additional 2 cats were fed 18 ml (n = 5) or 36 ml (n = 5) of a nutrient liquid meal labeled with technetium Tc 99m pentetate. Liquid-phase gastric emptying t1/2 then were determined by use of scintigraphy. Solid-phase gastric emptying t1/2 were between 210 and 769 minutes (median, 330 minutes). Median liquid-phase gastric emptying t1/2 after ingestion of 18 or 36 ml of the test meal were 67 minutes (range, 60 to 96 minutes) and 117 minutes (range, 101 to 170 minutes), respectively. The median t1/2 determined for cats receiving 18 ml of the radiolabeled liquid was significantly less than that determined for cats receiving 36 ml of the test meal. The protocol was tolerated by nonsedated cats. Solid-phase gastric emptying t1/2 were prolonged, compared with liquid-phase t1/2, and a major factor governing the emptying rate of liquids was the volume consumed. Nuclear scintigraphy may prove useful in assessing gastric motility disorders in cats.

Correlation Between Gastric Emptying and Gastric Adaptive Relaxation Influenced by Amino Acids

PubMed Central

Uchida, Masayuki; Kobayashi, Orie; Saito, Chizuru

2017-01-01

Background/Aims Amino acids have many physiological activities. We report the correlation between gastric emptying and gastric adaptive relaxation using tryptophan and amino acids with a straight alkyl chain, hydroxylated chain, and branched chain. Here we sought to further clarify the correlation between gastric emptying and gastric adaptive relaxation by using other amino acids. Methods In Sprague-Dawley rats, gastric emptying was evaluated by a breath test using [1-13C] acetic acid. The expired 13CO2 pattern, Tmax, Cmax, and AUC120min values were used as evaluation items. Gastric adaptive relaxation was evaluated in a barostat experiment. Individual amino acids (1 g/kg) were administered orally 30 minutes before each breath test or barostat test. Results L-phenylalanine and L-tyrosine did not influence gastric emptying. All other amino acids, ie, L-proline, L-histidine, L-cysteine, L-methionine, L-aspartic acid, L-glutamic acid, L-asparagine, L-arginine, L-glutamine, and L-lysine significantly delayed and inhibited gastric emptying. L-Cysteine and L-aspartic acid significantly enhanced and L-methionine and L-glutamine significantly inhibited gastric adaptive relaxation. L-Phenylalanine moved the balloon toward the antrum, suggesting strong contraction of the fundus. Tmax showed a significant positive correlation (r = 0.709), and Cmax and AUC120min each showed negative correlations (r = 0.613 and 0.667, respectively) with gastric adaptive relaxation. Conclusion From the above findings, it was found that a close correlation exists between gastric emptying and adaptive relaxation, suggesting that enhanced gastric adaptive relaxation inhibits gastric emptying. PMID:28335103

14 CFR 135.185 - Empty weight and center of gravity: Currency requirement.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Empty weight and center of gravity... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.185 Empty weight and center of gravity: Currency... gravity are calculated from values established by actual weighing of the aircraft within the preceding 36...

14 CFR 135.185 - Empty weight and center of gravity: Currency requirement.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Empty weight and center of gravity... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.185 Empty weight and center of gravity: Currency... gravity are calculated from values established by actual weighing of the aircraft within the preceding 36...

14 CFR 135.185 - Empty weight and center of gravity: Currency requirement.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Empty weight and center of gravity... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.185 Empty weight and center of gravity: Currency... gravity are calculated from values established by actual weighing of the aircraft within the preceding 36...

14 CFR 135.185 - Empty weight and center of gravity: Currency requirement.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Empty weight and center of gravity... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.185 Empty weight and center of gravity: Currency... gravity are calculated from values established by actual weighing of the aircraft within the preceding 36...

14 CFR 135.185 - Empty weight and center of gravity: Currency requirement.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Empty weight and center of gravity... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.185 Empty weight and center of gravity: Currency... gravity are calculated from values established by actual weighing of the aircraft within the preceding 36...

Why the self is empty. Toward a historically situated psychology.

PubMed

Cushman, P

1990-05-01

This article presents a contextualized treatment of the current configuration of self, some of the pathologies that plague it, and the technologies that attempt to heal it. Of particular interest is the historical shift from the Victorian, sexually restricted self to the post-World War II empty self. The empty self is soothed and made cohesive by becoming "filled up" with food, consumer products, and celebrities. Its historical antecedents, economic constituents, and political consequences are the focus of this article. The two professions most responsible for healing the empty self, advertising and psychotherapy, find themselves in a bind: They must treat a psychological symptom without being able to address its historical causes. Both circumvent the bind by employing the life-style solution, a strategy that attempts to heal by covertly filling the empty self with the accoutrements, values, and mannerisms of idealized figures. This strategy solves an old problem but creates new ones, including an opportunity for abuse by exploitive therapists, cult leaders, and politicians. Psychology's role in constructing the empty self, and thus reproducing the current hierarchy of power and privilege, is examined.

Impact of insecticide-treated bed nets on malaria transmission indices on the south coast of Kenya

PubMed Central

2011-01-01

Background Besides significantly reducing malaria vector densities, prolonged usage of bed nets has been linked to decline of Anopheles gambiae s.s. relative to Anopheles arabiensis, changes in host feeding preference of malaria vectors, and behavioural shifts to exophagy (outdoor biting) for the two important malaria vectors in Africa, An. gambiae s.l. and Anopheles funestus. In southern coastal Kenya, bed net use was negligible in 1997-1998 when Anopheles funestus and An. gambiae s.s. were the primary malaria vectors, with An. arabiensis and Anopheles merus playing a secondary role. Since 2001, bed net use has increased progressively and reached high levels by 2009-2010 with corresponding decline in malaria transmission. Methods To evaluate the impact of the substantial increase in household bed net use within this area on vector density, vector composition, and human-vector contact, indoor and outdoor resting mosquitoes were collected in the same region during 2009-2010 using pyrethrum spray catches and clay pots for indoor and outdoor collections respectively. Information on bed net use per sleeping spaces and factors influencing mosquito density were determined in the same houses using Poisson regression analysis. Species distribution was determined, and number of mosquitoes per house, human-biting rates (HBR), and entomological inoculation rate (EIR) were compared to those reported for the same area during 1997-1998, when bed net coverage had been minimal. Results Compared to 1997-1998, a significant decline in the relative proportion of An. gambiae s.s. among collected mosquitoes was noted, coupled with a proportionate increase of An. arabiensis. Following > 5 years of 60-86% coverage with bed nets, the density, human biting rate and EIR of indoor resting mosquitoes were reduced by more than 92% for An. funestus and by 75% for An. gambiae s.l. In addition, the host feeding choice of both vectors shifted more toward non-human vertebrates. Besides bed net use, malaria vector abundance was also influenced by type of house construction and according to whether one sleeps on a bed or a mat (both of these are associated with household wealth). Mosquito density was positively associated with presence of domestic animals. Conclusions These entomological indices indicate a much reduced human biting rate and a diminishing role of An. gambiae s.s. in malaria transmission following high bed net coverage. While increasing bed net coverage beyond the current levels may not significantly reduce the transmission potential of An. arabiensis, it is anticipated that increasing or at least sustaining high bed net coverage will result in a diminished role for An. funestus in malaria transmission. PMID:22165904

Experimental Study on Thermal Conductivity and Hardness of Cu and Ni Nanoparticle Packed Bed for Thermoelectric Application

NASA Astrophysics Data System (ADS)

Lin, Zi-Zhen; Huang, Cong-Liang; Zhen, Wen-Kai; Feng, Yan-Hui; Zhang, Xin-Xin; Wang, Ge

2017-03-01

The hot-wire method is applied in this paper to probe the thermal conductivity (TC) of Cu and Ni nanoparticle packed beds (NPBs). A different decrease tendency of TC versus porosity than that currently known is discovered. The relationship between the porosity and nanostructure is investigated to explain this unusual phenomenon. It is found that the porosity dominates the TC of the NPB in large porosities, while the TC depends on the contact area between nanoparticles in small porosities. Meanwhile, the Vickers hardness (HV) of NPBs is also measured. It turns out that the enlarged contact area between nanoparticles is responsible for the rapid increase of HV in large porosity, and the saturated nanoparticle deformation is responsible for the small increase of HV in low porosity. With both TC and HV considered, it can be pointed out that a structure of NPB with a porosity of 0.25 is preferable as a thermoelectric material because of the low TC and the higher hardness. Although Cu and Ni are not good thermoelectric materials, this study is supposed to provide an effective way to optimize thermoelectric figure of merit (ZT) and HV of nanoporous materials prepared by the cold-pressing method.

Comparison of reactivity to a metallic disc and 2% aluminium salt in 366 children, and reproducibility over time for 241 young adults with childhood vaccine-related aluminium contact allergy.

PubMed

Gente Lidholm, Anette; Inerot, Annica; Gillstedt, Martin; Bergfors, Elisabet; Trollfors, Birger

2018-07-01

An aluminium hydroxide-adsorbed pertussis toxoid vaccine was studied in 76 000 children in the 1990s in Gothenburg, Sweden. Long-lasting itchy subcutaneous nodules at the vaccination site were seen in 745 participants. Of 495 children with itchy nodules who were patch tested for aluminium allergy, 377 were positive. In 2007-2008, 241 of the positive children were retested. Only in one third were earlier positive results reproduced. To further describe patch test reactions to different aluminium compounds in children with vaccine-induced aluminium allergy. Positive patch test results for metallic aluminium (empty Finn Chamber) and aluminium chloride hexahydrate 2% petrolatum (pet.) were analysed in 366 children with vaccine-induced persistent itching nodules tested in 1998-2002. Of those, 241 were tested a second time (2007-2008), and the patch test results of the two aluminium preparations were analysed. Patch testing with aluminium chloride hexahydrate 2% pet. is a more sensitive way to diagnose aluminium contact allergy than patch testing with metallic aluminium. A general decrease in the strength of reactions to both aluminium preparations in 241 children tested twice was observed. Aluminium contact allergy can be diagnosed by patch testing without using metallic aluminium. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Adsorption of mercury from aqueous solutions using palm oil fuel ash as an adsorbent - batch studies

NASA Astrophysics Data System (ADS)

Imla Syafiqah, M. S.; Yussof, H. W.

2018-03-01

Palm oil fuel ash (POFA) is one of the most abundantly produced waste materials. POFA is widely used by the oil palm industry which was collected as ash from the burning of empty fruit bunches fiber (EFB) and palm oil kernel shells (POKS) in the boiler as fuel to generate electricity. Mercury adsorption was conducted in a batch process to study the effects of contact time, initial Hg(II) ion concentration, and temperature. In this study, POFA was prepared and used for the removal of mercury(II) ion from the aqueous phase. The effects of various parameters such as contact time (0- 360 min), temperature (15 – 45 °C) and initial Hg(II) ion concentration (1 – 5 mg/L) for the removal of Hg(II) ion were studied in a batch process. The surface characterization was examined by scanning electron microscopy (SEM) and particle size distribution analysis. From this study, it was found that the highest Hg(II) ion removal was 99.60 % at pH 7, contact time of 4 h, initial Hg(II) ion concentration of 1 mg/L, adsorbent dosage 0.25 g and agitation speed of 100 rpm. The results implied that POFA has the potential as a low-cost and environmental friendly adsorbent for the removal of mercury from aqueous solution.

The contact heat transfer between the heating plate and granular materials in rotary heat exchanger under overloaded condition

NASA Astrophysics Data System (ADS)

Duan, Luanfang; Qi, Chonggang; Ling, Xiang; Peng, Hao

2018-03-01

In the present work, the contact heat transfer between the granular materials and heating plates inside plate rotary heat exchanger (PRHE) was investigated. The heat transfer coefficient is dominated by the contact heat transfer coefficient at hot wall surface of the heating plates and the heat penetration inside the solid bed. A plot scale PRHE with a diameter of Do = 273 mm and a length of L = 1000 mm has been established. Quartz sand with dp = 2 mm was employed as the experimental material. The operational parameters were in the range of ω = 1 - 8 rpm, and F = 15, 20, 25, 30%, and the effect of these parameters on the time-average contact heat transfer coefficient was analyzed. The time-average contact heat transfer coefficient increases with the increase of rotary speed, but decreases with the increase of the filling degree. The measured data of time-average heat transfer coefficients were compared with theoretical calculations from Schlünder's model, a good agreement between the measurements and the model could be achieved, especially at a lower rotary speed and filling degree level. The maximum deviation between the calculated data and the experimental data is approximate 10%.

Solid Test Meal to Measure the Gastric Emptying with Magnetogastrography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reynaga-Ornelas, M. G.; Roca-Chiapas, J. M. de ls; Cordova-Fraga, T.

2008-08-11

The gastric emptying is the time of evacuating the food ingested from the stomach to the duodenum in a controlled rate. Diverse studies express the results of the gastric emptying in form of half-time (t{sub 1/2}). The Magnetogastrography (MGG) is a biomagnetic technique that has the advantage of not being invasive, radiation free and does not interfere with the privacy of the subject. The objective was to analyze the magnetic signal of magnetic tracers mixed in a solid food to measure gastric emptying using Magnetogastrography. The ingested test meal displayed a magnetic signal, which served to obtain the signal registeredmore » by the fluxgate and the peristaltic contractions could be calculated while the stomach was emptying. The solid food product developed results to work satisfactorily in magnetogastrography.« less

Effect of synthetic prostaglandin E1 analog on gastric emptying of meals in man.

PubMed

Moore, J G; Alazraki, N; Clay, G D

1986-01-01

Forty-five subjects with healed duodenal ulcer were administered either a placebo or a low-dose or high-dose regimen of misoprostol, a synthetic PGE1 analog, in a double-blind, random, parallel-group design to assess the effect of this prostaglandin compound on the gastric emptying of liquid-solid meals. A dual-radionuclide technique to measure liquid- and solid-phase gastric emptying rates of physiological meals by external gamma camera imaging was used. All subjects had a pretreatment control (baseline) evaluation, followed one week later by a treatment-influenced emptying study. The results demonstrated that misoprostol did not significantly alter gastric emptying of either liquids or solids; however, these results cannot be extrapolated to other prostaglandin compounds because of the diverse and sometimes paradoxical effects of different prostaglandins on gastric motility.

Does postprandial itopride intake affect the rate of gastric emptying? A crossover study using the continuous real time 13C breath test (BreathID system).

PubMed

Nonaka, Takashi; Kessoku, Takaomi; Ogawa, Yuji; Yanagisawa, Shogo; Shiba, Tadahiko; Sahaguchi, Takashi; Atsukawa, Kazuhiro; Takahashi, Hisao; Sekino, Yusuke; Iida, Hiroshi; Hosono, Kunihiro; Endo, Hiroki; Sakamoto, Yasunari; Koide, Tomoko; Takahashi, Hirokazu; Tokoro, Chikako; Abe, Yasunobu; Maeda, Shin; Nakajima, Atsushi; Inamori, Masahiko

2011-01-01

The aim of this study was to determine whether oral Itopride hydrochloride (itopride) intake might have any effect on the rate of gastric emptying, using a novel non-invasive technique for measuring the rate of gastric emptying, namely, the continuous real time 13C breath test (BreathID system: Exalenz Bioscience Ltd., Israel). Eight healthy male volunteers participated in this randomized, two-way crossover study. The subjects fasted overnight and were randomly assigned to receive 50mg itopride following a test meal (200 kcal per 200mL, containing 100mg 13C acetate), or the test meal alone. Under both conditions, gastric emptying was monitored for 4 hours after administration of the test meal by the 13C-acetic acid breath test performed continually using the BreathID system. Using Oridion Research Software (beta version), the time required for emptying of 50% of the labeled meal (T 1/2), the analog to the scintigraphy lag time for 10% emptying of the labeled meal (T lag), the gastric emptying coefficient (GEC), and the regression-estimated constants (beta and kappa) were calculated. The parameters measured under the two conditions were compared using the Wilcoxon's signed-rank test. No significant differences in the calculated parameters, namely, the T 1/2, T lag, GEC, beta or kappa, were observed between the two test conditions, namely, administration of a test meal+itopride and administration of the test meal alone. The present study revealed that postprandial itopride intake had no significant influence on the rate of gastric emptying. Recently, several studies have shown that itopride may be effective in the treatment of patients with functional dyspepsia. Our results suggest that the efficacy of itopride in patients with functional dyspepsia may be based on its effect of improving functions other than the rate of gastric emptying, such as the activities at neuronal sites, brain-gut correlation, visceral hypersensitivity, gastric accommodation and distension-induced adaptation.

A double-blind comparison of clebopride and placebo in dyspepsia secondary to delayed gastric emptying.

PubMed

Bavestrello, L; Caimi, L; Barbera, A

1985-01-01

Seventy-six patients suffering from dyspeptic symptoms secondary to roentgenologically demonstrated delayed gastric emptying were treated with clebopride (0.5 mg TID) or with placebo during a three-month double-blind trial. Clebopride was more effective (P less than or equal to 0.001) than placebo in reducing or relieving symptoms and roentgenological findings associated with delayed gastric emptying. No interactions of clebopride with concomitant drugs or coexisting disorders were observed, and the incidence of side effects was low. We conclude that clebopride will be beneficial in the management of patients with delayed gastric emptying.