Preliminary Description of Stresses in Railroad Rail

DOT National Transportation Integrated Search

1976-11-01

One portion of the Federal Railroad Administration's (FRA) Track Performance Improvement Program is the development of engineering and analytic techniques required for the design and maintenance of railroad track of increased integrity and safety. Un...

Preliminary study of optimum ductburning turbofan engine cycle design parameters for supersonic cruising

NASA Technical Reports Server (NTRS)

Fishbach, L. H.

1978-01-01

The effect of turbofan engine overall pressure ratio, fan pressure ratio, and ductburner temperature rise on the engine weight and cruise fuel consumption for a mach 2.4 supersonic transport was investigated. Design point engines, optimized purely for the supersonic cruising portion of the flight where the bulk of the fuel is consumed, are considered. Based on constant thrust requirements at cruise, fuel consumption considerations would favor medium by pass ratio engines (1.5 to 1.8) of overall pressure ratio of about 16. Engine weight considerations favor low bypass ratio (0.6 or less) and low wverall pressure ratio (8). Combination of both effects results in bypass ratios of 0.6 to 0.8 and overall pressure ratio of 12 being the overall optimum.

Laboratory and Industrial Ventilation

NASA Technical Reports Server (NTRS)

1972-01-01

This handbook supplements the Facilities Engineering Handbook (NHB 7320.1) and provides additional policies and criteria for uniform application to ventilation systems. It expands basic requirements, provides additional design and construction guidance, and places emphasis on those design considerations which will provide for greater effectiveness in the use of these systems. The provisions of this handbook are applicable to all NASA field installations and the Jet Propulsion Laboratory. Since supply of this handbook is limited, abstracts of the portion or portions applicable to a given requirement will be made for the individual specific needs encountered rather than supplying copies of the handbook as has been past practice.

Vicher: A Virtual Reality Based Educational Module for Chemical Reaction Engineering.

ERIC Educational Resources Information Center

Bell, John T.; Fogler, H. Scott

1996-01-01

A virtual reality application for undergraduate chemical kinetics and reactor design education, Vicher (Virtual Chemical Reaction Model) was originally designed to simulate a portion of a modern chemical plant. Vicher now consists of two programs: Vicher I that models catalyst deactivation and Vicher II that models nonisothermal effects in…

32 CFR 250.8 - Pertinent portions of International Traffic in Arms Regulations (ITAR).

Code of Federal Regulations, 2010 CFR

2010-07-01

... details of development, engineering, design, production, or manufacture of any arms, ammunition, or... the details of design, production, or manufacture of any arms, ammunition, or implements of war on the..., production, or manufacturing of any arms, ammunition, or implements of war on the U.S. Munitions List. (3) If...

33 CFR 148.105 - What must I include in my application?

Code of Federal Regulations, 2010 CFR

2010-07-01

... engineering firm, if known, that will design the deepwater port or a portion of the port, the application must... only product the port is designed to transport, the throughput report may be limited to reporting crude... survey of the proposed marine site. This survey should provide data on the water depth, prevailing...

Advanced engineering environment collaboration project.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamph, Jane Ann; Pomplun, Alan R.; Kiba, Grant W.

2008-12-01

The Advanced Engineering Environment (AEE) is a model for an engineering design and communications system that will enhance project collaboration throughout the nuclear weapons complex (NWC). Sandia National Laboratories and Parametric Technology Corporation (PTC) worked together on a prototype project to evaluate the suitability of a portion of PTC's Windchill 9.0 suite of data management, design and collaboration tools as the basis for an AEE. The AEE project team implemented Windchill 9.0 development servers in both classified and unclassified domains and used them to test and evaluate the Windchill tool suite relative to the needs of the NWC using weaponsmore » project use cases. A primary deliverable was the development of a new real time collaborative desktop design and engineering process using PDMLink (data management tool), Pro/Engineer (mechanical computer aided design tool) and ProductView Lite (visualization tool). Additional project activities included evaluations of PTC's electrical computer aided design, visualization, and engineering calculations applications. This report documents the AEE project work to share information and lessons learned with other NWC sites. It also provides PTC with recommendations for improving their products for NWC applications.« less

Failure modes and effects analysis automation

NASA Technical Reports Server (NTRS)

Kamhieh, Cynthia H.; Cutts, Dannie E.; Purves, R. Byron

1988-01-01

A failure modes and effects analysis (FMEA) assistant was implemented as a knowledge based system and will be used during design of the Space Station to aid engineers in performing the complex task of tracking failures throughout the entire design effort. The three major directions in which automation was pursued were the clerical components of the FMEA process, the knowledge acquisition aspects of FMEA, and the failure propagation/analysis portions of the FMEA task. The system is accessible to design, safety, and reliability engineers at single user workstations and, although not designed to replace conventional FMEA, it is expected to decrease by many man years the time required to perform the analysis.

Using System Dynamics Analysis for Evaluating the Sustainability of “Complete Streets” Practices

EPA Science Inventory

If “complete streets” practices are followed, transportation corridor designs accommodate multiple modes of transportation. When transportation engineers and planners consider implementing these practices, they must decide what portion of a transportation corridor&rs...

Design of Sensors for Control of Closed Loop Life Support Systems

NASA Technical Reports Server (NTRS)

1990-01-01

A brief summary is presented of a Engineering Design sequence, a cooperation between NASA-Kennedy and the University of Florida on the Controlled Environmental Life Support System (CELSS) program. Part of the class was devoted to learning general principles and techniques of design. The next portion of the class was devoted to learning to design, actually fabricating and testing small components and subsystems of a CELSS.

A preliminary design and analysis of an advanced heat-rejection system for an extreme altitude advanced variable cycle diesel engine installed in a high-altitude advanced research platform

NASA Technical Reports Server (NTRS)

Johnston, Richard P.

1992-01-01

Satellite surveillance in such areas as the Antarctic indicates that from time to time concentration of ozone grows and shrinks. An effort to obtain useful atmospheric data for determining the causes of ozone depletion would require a flight capable of reaching altitudes of at least 100,000 ft and flying subsonically during the sampling portion of the mission. A study of a heat rejection system for an advanced variable cycle diesel (AVCD) engine was conducted. The engine was installed in an extreme altitude, high altitude advanced research platform. Results indicate that the waste heat from an AVCD engine propulsion system can be rejected at the maximum cruise altitude of 120,000 ft. Fifteen performance points, reflecting the behavior of the engine as the vehicle proceeded through the mission, were used to characterize the heat exchanger operation. That portion of the study is described in a appendix titled, 'A Detailed Study of the Heat Rejection System for an Extreme Altitude Atmospheric Sampling Aircraft,' by a consultant, Mr. James Bourne, Lytron, Incorporated.

Considerations for a design and operations knowledge support system for Space Station Freedom

NASA Technical Reports Server (NTRS)

Erickson, Jon D.; Crouse, Kenneth H.; Wechsler, Donald B.; Flaherty, Douglas R.

1989-01-01

Engineering and operations of modern engineered systems depend critically upon detailed design and operations knowledge that is accurate and authoritative. A design and operations knowledge support system (DOKSS) is a modern computer-based information system providing knowledge about the creation, evolution, and growth of an engineered system. The purpose of a DOKSS is to provide convenient and effective access to this multifaceted information. The complexity of Space Station Freedom's (SSF's) systems, elements, interfaces, and organizations makes convenient access to design knowledge especially important, when compared to simpler systems. The life cycle length, being 30 or more years, adds a new dimension to space operations, maintenance, and evolution. Provided here is a review and discussion of design knowledge support systems to be delivered and operated as a critical part of the engineered system. A concept of a DOKSS for Space Station Freedom (SSF) is presented. This is followed by a detailed discussion of a DOKSS for the Lyndon B. Johnson Space Center and Work Package-2 portions of SSF.

The environmental control and life-support system for a lunar base: What drives its design

NASA Technical Reports Server (NTRS)

Hypes, Warren D.; Hall, John B., Jr.

1992-01-01

The purpose of this paper is to identify and briefly discuss some of the ground rules and mission scenario details that become drivers of the environmental control and life support (ECLS) system design and of the logistics related to the design. This paper is written for mission planners and non-ECLS system engineers to inform them of the details that will be important to the ECLS engineer when the design phase is reached. In addition, examples illustrate the impact of some selected mission characteristics on the logistics associated with ECLS systems. The last section of this paper focuses on the ECLS system technology development sequence and highlights specific portions that need emphasis.

A numerical investigation on the influence of engine shape and mixing processes on wave engine performance

NASA Astrophysics Data System (ADS)

Erickson, Robert R.

Wave engines are a class of unsteady, air-breathing propulsion devices that use an intermittent combustion process to generate thrust. The inherently simple mechanical design of the wave engine allows for a relatively low cost per unit propulsion system, yet unsatisfactory overall performance has severely limited the development of commercially successful wave engines. The primary objective of this investigation was to develop a more detailed physical understanding of the influence of gas dynamic nonlinearities, unsteady combustion processes, and engine shape on overall wave engine performance. Within this study, several numerical models were developed and applied to wave engines and related applications. The first portion of this investigation examined the influence of duct shape on driven oscillations in acoustic compression devices, which represent a simplified physical system closely related in several ways to the wave engine. A numerical model based on an application of the Galerkin method was developed to simulate large amplitude, one-dimensional acoustic waves driven in closed ducts. Results from this portion of the investigation showed that gas-dynamic nonlinearities significantly influence the properties of driven oscillations by transferring acoustic energy from the fundamental driven mode into higher harmonic modes. The second portion of this investigation presented and analyzed results from a numerical model of wave engine dynamics based on the quasi one-dimensional conservation equations in addition to separate sub-models for mixing and heat release. This model was then used to perform parametric studies of the characteristics of mixing and engine shape. The objectives of these studies were to determine the influence of mixing characteristics and engine shape on overall wave engine performance and to develop insight into the physical processes controlling overall performance trends. Results from this model showed that wave engine performance was strongly dependent on the coupling between the unsteady heat release that drives oscillations in the engine and the characteristics that determine the acoustic properties of the engine such as engine shape and mean property gradients. Simulation results showed that average thrust generation decreased dramatically when the natural acoustic mode frequencies of the engine and the frequency content of the unsteady heat release were not aligned.

Collaborative engineering and design management for the Hobby-Eberly Telescope tracker upgrade

NASA Astrophysics Data System (ADS)

Mollison, Nicholas T.; Hayes, Richard J.; Good, John M.; Booth, John A.; Savage, Richard D.; Jackson, John R.; Rafal, Marc D.; Beno, Joseph H.

2010-07-01

The engineering and design of systems as complex as the Hobby-Eberly Telescope's* new tracker require that multiple tasks be executed in parallel and overlapping efforts. When the design of individual subsystems is distributed among multiple organizations, teams, and individuals, challenges can arise with respect to managing design productivity and coordinating successful collaborative exchanges. This paper focuses on design management issues and current practices for the tracker design portion of the Hobby-Eberly Telescope Wide Field Upgrade project. The scope of the tracker upgrade requires engineering contributions and input from numerous fields including optics, instrumentation, electromechanics, software controls engineering, and site-operations. Successful system-level integration of tracker subsystems and interfaces is critical to the telescope's ultimate performance in astronomical observation. Software and process controls for design information and workflow management have been implemented to assist the collaborative transfer of tracker design data. The tracker system architecture and selection of subsystem interfaces has also proven to be a determining factor in design task formulation and team communication needs. Interface controls and requirements change controls will be discussed, and critical team interactions are recounted (a group-participation Failure Modes and Effects Analysis [FMEA] is one of special interest). This paper will be of interest to engineers, designers, and managers engaging in multi-disciplinary and parallel engineering projects that require coordination among multiple individuals, teams, and organizations.

Monitoring means for combustion engine electric storage battery means

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, G. K.; Rautiola, R. E.; Taylor, R. E.

Disclosed, in combination, are a combustion engine, an electric storage battery, an electrically powered starter motor for at times driving the engine in order to start the engine, and an electrical system monitor; the electrical system monitor has a first monitoring portion which senses the actual voltage across the battery and a second monitoring portion which monitors the current through the battery; an electrical switch controls associated circuitry and is actuatable into open or closed conditions; whenever the first monitoring portion senses a preselected magnitude of the actual voltage across the battery or the second monitoring portion senses a preselectedmore » magnitude of the current flow through the battery, the electrical switch is actuated.« less

Spacecraft systems engineering: An introduction to the process at GSFC

NASA Technical Reports Server (NTRS)

Fragomeni, Tony; Ryschkewitsch, Michael G.

1993-01-01

The main objective in systems engineering is to devise a coherent total system design capable of achieving the stated requirements. Requirements should be rigid. However, they should be continuously challenged, rechallenged and/or validated. The systems engineer must specify every requirement in order to design, document, implement and conduct the mission. Each and every requirement must be logically considered, traceable and evaluated through various analysis and trade studies in a total systems design. Margins must be determined to be realistic as well as adequate. The systems engineer must also continuously close the loop and verify system performance against the requirements. The fundamental role of the systems engineer, however, is to engineer, not manage. Yet, in large, complex missions, where more than one systems engineer is required, someone needs to manage the systems engineers, and we call them 'systems managers.' Systems engineering management is an overview function which plans, guides, monitors and controls the technical execution of a project as implemented by the systems engineers. As the project moves on through Phases A and B into Phase C/D, the systems engineering tasks become a small portion of the total effort. The systems management role increases since discipline subsystem engineers are conducting analyses and reviewing test data for final review and acceptance by the systems managers.

Development of Integrated Programs for Aerospace-vehicle design (IPAD): Integrated information processing requirements

NASA Technical Reports Server (NTRS)

Southall, J. W.

1979-01-01

The engineering-specified requirements for integrated information processing by means of the Integrated Programs for Aerospace-Vehicle Design (IPAD) system are presented. A data model is described and is based on the design process of a typical aerospace vehicle. General data management requirements are specified for data storage, retrieval, generation, communication, and maintenance. Information management requirements are specified for a two-component data model. In the general portion, data sets are managed as entities, and in the specific portion, data elements and the relationships between elements are managed by the system, allowing user access to individual elements for the purpose of query. Computer program management requirements are specified for support of a computer program library, control of computer programs, and installation of computer programs into IPAD.

An improved turbine disk design to increase reliability of aircraft jet engines

NASA Technical Reports Server (NTRS)

Barack, W. N.; Domas, P. A.

1976-01-01

An analytical study was performed on a novel disk design to replace the existing high-pressure turbine, stage 1 disk on the CF6-50 turbofan engine. Preliminary studies were conducted on seven candidate disk design concepts. An integral multidisk design with bore entry of the turbine blade cooling air was selected as the improved disk design. This disk has the unique feature of being redundant such that if one portion of the disk would fail, the remaining portion would prevent the release of large disk fragments from the turbine system. Low cycle fatigue lives, initial defect propagation lives, burst speed, and the kinetic energies of probable disk fragment configurations were calculated, and comparisons were made with the existing disk, both in its current material, IN 718, and with the substitution of an advanced alloy, Rene 95. The design for redundancy approach which necessitated the addition of approximately 44.5 kg (98 lb) to the design disk substantially improved the life of the disk. The life to crack initiation was increased from 30,000 cycles to more than 100,000 cycles. The cycles to failure from initial defect propagation were increased from 380 cycles to 1564 cycles. Burst speed was increased from 126 percent overspeed to 149 percent overspeed. Additionally, the maximum fragment energies associated with a failure were decreased by an order of magnitude.

Soot and liquid-phase fuel distributions in a newly designed optically accessible DI diesel engine

NASA Astrophysics Data System (ADS)

Dec, J. E.; Espey, C.

1993-10-01

Two-dimensional (2-D) laser-sheet imaging has been used to examine the soot and liquid-phase fuel distributions in a newly designed, optically accessible, direct-injection diesel engine of the heavy-duty size class. The design of this engine preserves the intake port geometry and basic dimensions of a Cummins N-series production engine. It also includes several unique features to provide considerable optical access. Liquid-phase fuel and soot distribution studies were conducted at a medium speed (1,200 rpm) using a Cummins closed-nozzle fuel injector. The scattering was used to obtain planar images of the liquid-phase fuel distribution. These images show that the leading edge of the liquid-phase portion of the fuel jet reaches a maximum length of 24 mm, which is about half the combustion bowl radius for this engine. Beyond this point virtually all the fuel has vaporized. Soot distribution measurements were made at a high load condition using three imaging diagnostics: natural flame luminosity, 2-D laser-induced incandescence, and 2-D elastic scattering. This investigation showed that the soot distribution in the combusting fuel jet develops through three stages. First, just after the onset of luminous combustion, soot particles are small and nearly uniformly distributed throughout the luminous region of the fuel jet. Second, after about 2 crank angle degrees a pattern develops of a higher soot concentration of larger sized particles in the head vortex region of the jet and a lower soot concentration of smaller sized particles upstream toward the injector. Third, after fuel injection ends, both the soot concentration and soot particle size increase rapidly in the upstream portion of the fuel jet.

Historical perspective - Viking Mars Lander propulsion

NASA Technical Reports Server (NTRS)

Morrisey, Donald C.

1989-01-01

This paper discusses the Viking 1 and 2 missions to Mars in 1975-1976 and describes the design evolution of the Viking Terminal Descent Rocket Engines responsible for decelerating the Viking Mars Landers during the final portion of their descent from orbit. The Viking Terminal Descent Rocket Engines have twice the thrust of the largest monopropellant hydrazine engine developed previously but weigh considerably less. The engine has 18 nozzles, the capability of 10:1 throttling, is totally sealed until fired, employs no organic unsealed materials, is 100 percent germ free, utilized hydrazine STM-20 as the propellant, and starts at a temperature more than 45 F below the propellant's freezing point.

Combustion engine variable compression ratio apparatus and method

DOEpatents

Lawrence,; Keith, E [Peoria, IL; Strawbridge, Bryan E [Dunlap, IL; Dutart, Charles H [Washington, IL

2006-06-06

An apparatus and method for varying a compression ratio of an engine having a block and a head mounted thereto. The apparatus and method includes a cylinder having a block portion and a head portion, a piston linearly movable in the block portion of the cylinder, a cylinder plug linearly movable in the head portion of the cylinder, and a valve located in the cylinder plug and operable to provide controlled fluid communication with the block portion of the cylinder.

32 CFR 250.8 - Pertinent portions of International Traffic in Arms Regulations (ITAR).

Code of Federal Regulations, 2013 CFR

2013-07-01

... details of development, engineering, design, production, or manufacture of any arms, ammunition, or... U.S. party so certifies and complies with the requirements of the Department of Defense Industrial... requirements of the Department of Defense Industrial Security Manual relating to the transmission of such...

32 CFR 250.8 - Pertinent portions of International Traffic in Arms Regulations (ITAR).

Code of Federal Regulations, 2011 CFR

2011-07-01

... details of development, engineering, design, production, or manufacture of any arms, ammunition, or... U.S. party so certifies and complies with the requirements of the Department of Defense Industrial... requirements of the Department of Defense Industrial Security Manual relating to the transmission of such...

Fan Cart: The Next Generation

NASA Astrophysics Data System (ADS)

Lamore, Brian

2016-10-01

For years the fan cart has provided physics students with an excellent resource for exploring fundamental mechanics concepts such as acceleration, Newton's laws, impulse, momentum, work-energy, and energy conversions. The Physics Teacher has even seen some excellent do-it-yourself (DIY) fan carts and activities. If you are interested in developing the `E' portion of your and your students' STEM (science, technology, engineering, and math) skills, one way to accomplish this is to revisit the DIY fan cart. In this article I share a design of a new edition of the DIY fan cart and some ideas for incorporating the engineering design process into your high school curriculum.

Fuel premixing module for gas turbine engine combustor

NASA Technical Reports Server (NTRS)

Chin, Jushan (Inventor); Rizk, Nader K. (Inventor); Razdan, Mohan K. (Inventor); Marshall, Andre W. (Inventor)

2005-01-01

A fuel-air premixing module is designed to reduce emissions from a gas turbine engine. In one form, the premixing module includes a central pilot premixer module with a main premixer module positioned thereround. Each of the portions of the fuel-air premixing module include an axial inflow swirler with a plurality of fixed swirler vanes. Fuel is injected into the main premixer module between the swirler vanes of the axial inflow swirler and at an acute angle relative to the centerline of the premixing module.

Extended Operation of Turbojet Engine with Pentaborane

NASA Technical Reports Server (NTRS)

Useller, James W; Jones, William L

1957-01-01

A full-scale turbojet engine was operated with pentaborane fuel continuously for 22 minutes at conditions simulating flight at a Mach number of 0.8 at an altitude of 50,000 feet. This period of operation is approximately three times longer than previously reported operation times. Although the specific fuel consumption was reduced from 1.3 with JP-4 fuel to 0.98 with pentaborane, a 13.2-percent reduction in net thrust was also encountered. A portion of this thrust loss is potentially recoverable with proper design of the engine components. The boron oxide deposition and erosion processes within the engine approached an equilibrium condition after approximately 22 minutes of operation with pentaborane.

Fuel injection assembly for use in turbine engines and method of assembling same

DOEpatents

Uhm, Jong Ho; Johnson, Thomas Edward

2015-03-24

A fuel injection assembly for use in a turbine engine is provided. The fuel injection assembly includes a plurality of tube assemblies, wherein each of the tube assemblies includes an upstream portion and a downstream portion. Each tube assembly includes a plurality of tubes that extend from the upstream portion to the downstream portion or from the upstream portion through the downstream portion. At least one injection system is coupled to at least one tube assembly of the plurality of tube assemblies. The injection system includes a fluid supply member that extends from a fluid source to the downstream portion of the tube assembly. The fluid supply member includes a first end portion located in the downstream portion of the tube assembly, wherein the first end portion has at least one first opening for channeling fluid through the tube assembly to facilitate reducing a temperature therein.

Regenerator for gas turbine engine

DOEpatents

Lewakowski, John J.

1979-01-01

A rotary disc-type counterflow regenerator for a gas turbine engine includes a disc-shaped ceramic core surrounded by a metal rim which carries a coaxial annular ring gear. Bonding of the metal rim to the ceramic core is accomplished by constructing the metal rim in three integral portions: a driving portion disposed adjacent the ceramic core which carries the ring gear, a bonding portion disposed further away from the ceramic core and which is bonded thereto by elastomeric pads, and a connecting portion connecting the bonding portion to the driving portion. The elastomeric pads are bonded to radially flexible mounts formed as part of the metal rim by circumferential slots in the transition portion and lateral slots extending from one end of the circumferential slots across the bonding portion of the rim.

Application of fiber-reinforced bismaleimide materials to aircraft nacelle structures

NASA Technical Reports Server (NTRS)

Peros, Vasilios; Ruth, John; Trawinski, David

1992-01-01

Existing aircraft engine nacelle structures employ advanced composite materials to reduce weight and thereby increase overall performance. Use of advanced composite materials on existing aircraft nacelle structures includes fiber-reinforced epoxy structures and has typically been limited to regions furthest away from the hot engine core. Portions of the nacelle structure that are closer to the engine require materials with a higher temperature capability. In these portions, existing nacelle structures employ aluminum sandwich construction and skin/stringer construction. The aluminum structure is composed of many detail parts and assemblies and is usually protected by some form of ablative, insulator, or metallic thermal shield. A one-piece composite inner cowl for a new-generation engine nacelle structure has been designed using fiber-reinforced bismaleimide (BMI) materials and honeycomb core in a sandwich construction. The new composite design has many advantages over the existing aluminum structure. Multiple details were integrated into the one-piece composite design, thereby significantly reducing the number of detail parts and fasteners. The use of lightweight materials and the reduction of the number of joints result in a significant weight reduction over the aluminum design; manufacturing labor and the overall number of tools required have also been reduced. Several significant technical issues were addressed in the development of a BMI composite design. Technical evaluation of the available BMI systems led to the selection of a toughened BMI material which was resistant to microcracking under thermal cyclic loading and enhanced the damage tolerance of the structure. Technical evaluation of the degradation of BMI materials in contact with aluminum and other metals validated methods for isolation of the various materials. Graphite-reinforced BMI in contact with aluminum and some steels was found to degrade in salt spray testing. Isolation techniques such as those used for graphite-reinforced epoxy structures were shown to provide adequate protection. The springback and producibility of large BMI structures were evaluated by manufacturing prototype hardware which had the full-scale cross section of the one-piece composite structure.

Bulkhead insert for an internal combustion engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maki, Clifford E.; Chottiner, Jeffrey Eliot; Williams, Rick L.

An engine includes a cylinder block defining at least one main bearing bulkhead adjacent to a cylinder, and a crankshaft rotatably housed within the block by a main bearing. A bulkhead insert has a cap portion, and an insert portion provided within the bulkhead. The insert portion has having first and second end regions connected by first and second straps. Each strap having a flanged beam cross section. The first and second ends of the insert portion are configured to connect a main bearing cap column to a cylinder head column. Each of the first and second end regions definemore » at least one protrusion having a surface substantially normal to engine combustion and reactive loads. The cap portion is configured to mate with the first end region at the main bearing cap column and support the main bearing.« less

Enhancing non-technical skills by a multidisciplinary engineering summer school

NASA Astrophysics Data System (ADS)

Larsen, Peter Gorm; Kristiansen, Erik Lasse; Bennedsen, Jens; Bjerge, Kim

2017-11-01

In general engineering studies focus on the technical skills in their own discipline. However, in their subsequent industrial careers, a significant portion of their time needs to be devoted to non-technical skills. In addition, in an increasingly globalised world collaboration in teams across cultures and disciplines is paramount to the creation of new and innovative products. In order to enhance the non-technical skills for groups of engineering students a series of innovation courses has been arranged and delivered in close collaboration with an industrial company (Bang & Olufsen). These courses have been organised as summer schools called 'Conceptual Design and Development of Innovative Products' (CD-DIP) and delivered outside the usual educational environment. In order to explore the impact of this single course, we have conducted a study among the students participating from 2007 to 2013. This has been carried out both qualitatively using interviews with selected students as well as quantitatively using a survey. The results are outstanding in demonstrating that the non-technical skills obtained in this single course have been of high value for a large portion of the students' subsequent professional life.

Hyper-X Engine Design and Ground Test Program

NASA Technical Reports Server (NTRS)

Voland, R. T.; Rock, K. E.; Huebner, L. D.; Witte, D. W.; Fischer, K. E.; McClinton, C. R.

1998-01-01

The Hyper-X Program, NASA's focused hypersonic technology program jointly run by NASA Langley and Dryden, is designed to move hypersonic, air-breathing vehicle technology from the laboratory environment to the flight environment, the last stage preceding prototype development. The Hyper-X research vehicle will provide the first ever opportunity to obtain data on an airframe integrated supersonic combustion ramjet propulsion system in flight, providing the first flight validation of wind tunnel, numerical and analytical methods used for design of these vehicles. A substantial portion of the integrated vehicle/engine flowpath development, engine systems verification and validation and flight test risk reduction efforts are experimentally based, including vehicle aeropropulsive force and moment database generation for flight control law development, and integrated vehicle/engine performance validation. The Mach 7 engine flowpath development tests have been completed, and effort is now shifting to engine controls, systems and performance verification and validation tests, as well as, additional flight test risk reduction tests. The engine wind tunnel tests required for these efforts range from tests of partial width engines in both small and large scramjet test facilities, to tests of the full flight engine on a vehicle simulator and tests of a complete flight vehicle in the Langley 8-Ft. High Temperature Tunnel. These tests will begin in the summer of 1998 and continue through 1999. The first flight test is planned for early 2000.

Advanced composite vertical stabilizer for DC-10 transport aircraft

NASA Technical Reports Server (NTRS)

Stephens, C. O.

1978-01-01

The structural design configuration for the Composite Vertical Stabilizer is described and the structural design, analysis, and weight activities are presented. The status of fabrication and test activities for the development test portion of the program is described. Test results are presented for the skin panels, spar web, spar cap to cover, and laminate properties specimens. Engineering drawings of vertification test panels and root fittings, rudder support specimens, titanium fittings, and rear spar specimen analysis models are included.

Solar Thermal Upper Stage Cryogen System Engineering Checkout Test

NASA Technical Reports Server (NTRS)

Olsen, A. D; Cady, E. C.; Jenkins, D. S.

1999-01-01

The Solar Thermal Upper Stage technology (STUSTD) program is a solar thermal propulsion technology program cooperatively sponsored by a Boeing led team and by NASA MSFC. A key element of its technology program is development of a liquid hydrogen (LH2) storage and supply system which employs multi-layer insulation, liquid acquisition devices, active and passive thermodynamic vent systems, and variable 40W tank heaters to reliably provide near constant pressure H2 to a solar thermal engine in the low-gravity of space operation. The LH2 storage and supply system is designed to operate as a passive, pressure fed supply system at a constant pressure of about 45 psia. During operation of the solar thermal engine over a small portion of the orbit the LH2 storage and supply system propulsively vents through the enjoy at a controlled flowrate. During the long coast portion of the orbit, the LH2 tank is locked up (unvented). Thus, all of the vented H2 flow is used in the engine for thrust and none is wastefully vented overboard. The key to managing the tank pressure and therefore the H2 flow to the engine is to manage and balance the energy flow into the LH2 tank with the MLI and tank heaters with the energy flow out of the LH2 tank through the vented H2 flow. A moderate scale (71 cu ft) LH2 storage and supply system was installed and insulated at the NASA MSFC Test Area 300. The operation of the system is described in this paper. The test program for the LH2 system consisted of two parts: 1) a series of engineering tests to characterize the performance of the various components in the system: and 2) a 30-day simulation of a complete LEO and GEO transfer mission. This paper describes the results of the engineering tests, and correlates these results with analytical models used to design future advanced Solar Orbit Transfer Vehicles.

System and method for engine combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sczomak, David P.; Gallon, Robert J.; Solomon, Arun S.

A combustion system for use with one or more cylinder bores of an internal combustion engine includes at least one cylinder head defining first and second intake ports in fluid communication with the one or more cylinder bores. A flap is adjustably connected to the at least one cylinder head. The flap includes a first flap portion cooperating with the first intake port extending from an arm and a second flap portion cooperating with the second intake port extending from the arm and disposed adjacent the first flap portion. A controller in electrical communication with an actuator monitors the conditionmore » of the engine and actuates the flap to position the first and second flap portions between first and second positions to create a first combustion condition and a second combustion condition.« less

Cascade Optimization Strategy Maximizes Thrust for High-Speed Civil Transport Propulsion System Concept

NASA Technical Reports Server (NTRS)

1995-01-01

The design of a High-Speed Civil Transport (HSCT) air-breathing propulsion system for multimission, variable-cycle operations was successfully optimized through a soft coupling of the engine performance analyzer NASA Engine Performance Program (NEPP) to a multidisciplinary optimization tool COMETBOARDS that was developed at the NASA Lewis Research Center. The design optimization of this engine was cast as a nonlinear optimization problem, with engine thrust as the merit function and the bypass ratios, r-values of fans, fuel flow, and other factors as important active design variables. Constraints were specified on factors including the maximum speed of the compressors, the positive surge margins for the compressors with specified safety factors, the discharge temperature, the pressure ratios, and the mixer extreme Mach number. Solving the problem by using the most reliable optimization algorithm available in COMETBOARDS would provide feasible optimum results only for a portion of the aircraft flight regime because of the large number of mission points (defined by altitudes, Mach numbers, flow rates, and other factors), diverse constraint types, and overall poor conditioning of the design space. Only the cascade optimization strategy of COMETBOARDS, which was devised especially for difficult multidisciplinary applications, could successfully solve a number of engine design problems for their flight regimes. Furthermore, the cascade strategy converged to the same global optimum solution even when it was initiated from different design points. Multiple optimizers in a specified sequence, pseudorandom damping, and reduction of the design space distortion via a global scaling scheme are some of the key features of the cascade strategy. HSCT engine concept, optimized solution for HSCT engine concept. A COMETBOARDS solution for an HSCT engine (Mach-2.4 mixed-flow turbofan) along with its configuration is shown. The optimum thrust is normalized with respect to NEPP results. COMETBOARDS added value in the design optimization of the HSCT engine.

Structural Optimization Methodology for Rotating Disks of Aircraft Engines

NASA Technical Reports Server (NTRS)

Armand, Sasan C.

1995-01-01

In support of the preliminary evaluation of various engine technologies, a methodology has been developed for structurally designing the rotating disks of an aircraft engine. The structural design methodology, along with a previously derived methodology for predicting low-cycle fatigue life, was implemented in a computer program. An interface computer program was also developed that gathers the required data from a flowpath analysis program (WATE) being used at NASA Lewis. The computer program developed for this study requires minimum interaction with the user, thus allowing engineers with varying backgrounds in aeropropulsion to successfully execute it. The stress analysis portion of the methodology and the computer program were verified by employing the finite element analysis method. The 10th- stage, high-pressure-compressor disk of the Energy Efficient Engine Program (E3) engine was used to verify the stress analysis; the differences between the stresses and displacements obtained from the computer program developed for this study and from the finite element analysis were all below 3 percent for the problem solved. The computer program developed for this study was employed to structurally optimize the rotating disks of the E3 high-pressure compressor. The rotating disks designed by the computer program in this study were approximately 26 percent lighter than calculated from the E3 drawings. The methodology is presented herein.

Preconstruction Engineering and Design Phase Reevaluation Report, Olcott Harbor Project, Olcott, New York. Volume 2, Supporting Documentation. Revision.

DTIC Science & Technology

1992-09-01

85 (saturated) : 0 : 26 3. Cell Fill (crushed stone) : 110 (moist) : 0 : 32 68 ( submerged ) 4. Breakwater Armor Stone : 110 (moist) : 0 40 68... submerged ) 5. Queenston Shale bedrock : unconfined compressive strength : au = 6,000 psi 7 5. PROJECT FEATURES FOR FINAL DESIGN a. Breakwaters. The project...existing conrete pad (550 feet from the retaining wall) the structure is submerged with isolated portions of the structure observable at the lake

A General-Purpose Optimization Engine for Multi-Disciplinary Design Applications

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Hopkins, Dale A.; Berke, Laszlo

1996-01-01

A general purpose optimization tool for multidisciplinary applications, which in the literature is known as COMETBOARDS, is being developed at NASA Lewis Research Center. The modular organization of COMETBOARDS includes several analyzers and state-of-the-art optimization algorithms along with their cascading strategy. The code structure allows quick integration of new analyzers and optimizers. The COMETBOARDS code reads input information from a number of data files, formulates a design as a set of multidisciplinary nonlinear programming problems, and then solves the resulting problems. COMETBOARDS can be used to solve a large problem which can be defined through multiple disciplines, each of which can be further broken down into several subproblems. Alternatively, a small portion of a large problem can be optimized in an effort to improve an existing system. Some of the other unique features of COMETBOARDS include design variable formulation, constraint formulation, subproblem coupling strategy, global scaling technique, analysis approximation, use of either sequential or parallel computational modes, and so forth. The special features and unique strengths of COMETBOARDS assist convergence and reduce the amount of CPU time used to solve the difficult optimization problems of aerospace industries. COMETBOARDS has been successfully used to solve a number of problems, including structural design of space station components, design of nozzle components of an air-breathing engine, configuration design of subsonic and supersonic aircraft, mixed flow turbofan engines, wave rotor topped engines, and so forth. This paper introduces the COMETBOARDS design tool and its versatility, which is illustrated by citing examples from structures, aircraft design, and air-breathing propulsion engine design.

Computational Tools for Metabolic Engineering

PubMed Central

Copeland, Wilbert B.; Bartley, Bryan A.; Chandran, Deepak; Galdzicki, Michal; Kim, Kyung H.; Sleight, Sean C.; Maranas, Costas D.; Sauro, Herbert M.

2012-01-01

A great variety of software applications are now employed in the metabolic engineering field. These applications have been created to support a wide range of experimental and analysis techniques. Computational tools are utilized throughout the metabolic engineering workflow to extract and interpret relevant information from large data sets, to present complex models in a more manageable form, and to propose efficient network design strategies. In this review, we present a number of tools that can assist in modifying and understanding cellular metabolic networks. The review covers seven areas of relevance to metabolic engineers. These include metabolic reconstruction efforts, network visualization, nucleic acid and protein engineering, metabolic flux analysis, pathway prospecting, post-structural network analysis and culture optimization. The list of available tools is extensive and we can only highlight a small, representative portion of the tools from each area. PMID:22629572

Phase-angle controller for Stirling engines

NASA Technical Reports Server (NTRS)

Mcdougal, A. R. (Inventor)

1980-01-01

An actuator includes a restraint link adapted to be connected with a pivotal carrier arm for a force transfer gear interposed between the crankshaft for an expander portion of a Stirling engine and a crankshaft for the displacer portion of the engine. The restraint link is releasably trapped hydraulic fluid for selectively establishing a phase angle relationship between the crankshaft. A second embodiment incorporates a hydraulic coupler for use in varying the phase angle of gear-coupled crank fpr a Stirling engine whereby phase angle changes are obtainable.

Reliability/maintainability/testability design for dormancy

NASA Astrophysics Data System (ADS)

Seman, Robert M.; Etzl, Julius M.; Purnell, Arthur W.

1988-05-01

This document has been prepared as a tool for designers of dormant military equipment and systems. The purpose of this handbook is to provide design engineers with Reliability/Maintainability/Testability design guidelines for systems which spend significant portions of their life cycle in a dormant state. The dormant state is defined as a nonoperating mode where a system experiences very little or no electrical stress. The guidelines in this report present design criteria in the following categories: (1) Part Selection and Control; (2) Derating Practices; (3) Equipment/System Packaging; (4) Transportation and Handling; (5) Maintainability Design; (6) Testability Design; (7) Evaluation Methods for In-Plant and Field Evaluation; and (8) Product Performance Agreements. Whereever applicable, design guidelines for operating systems were included with the dormant design guidelines. This was done in an effort to produce design guidelines for a more complete life cycle. Although dormant systems spend significant portions of their life cycle in a nonoperating mode, the designer must design the system for the complete life cycle, including nonoperating as well as operating modes. The guidelines are primarily intended for use in the design of equipment composed of electronic parts and components. However, they can also be used for the design of systems which encompass both electronic and nonelectronic parts, as well as for the modification of existing systems.

Systems for delivering liquified natural gas to an engine

DOEpatents

Bingham, Dennis N.; Wilding, Bruce M.; O'Brien, James E.; Siahpush, Ali S.; Brown, Kevin B.

2000-01-01

A fuel delivery system includes a fuel tank configured to receive liquid natural gas. A first conduit extends from a vapor holding portion of the fuel tank to an economizer valve. A second conduit extends from a liquid holding portion of the fuel tank to the economizer valve. Fluid coupled to the economizer valve is a vaporizer which is heated by coolant from the engine and is positioned below the fuel tank. The economizer valve selectively withdraws either liquid natural gas or vaporized natural gas from the fuel tank depending on the pressure within the vapor holding portion of the fuel tank. A delivery conduit extends from the vaporizer to the engine. A return conduit having a check valve formed therein extends from the delivery conduit to the vapor holding portion of the fuel tank for pressurizing the fuel tank.

Low latency, high bandwidth data communications between compute nodes in a parallel computer

DOEpatents

Archer, Charles J.; Blocksome, Michael A.; Ratterman, Joseph D.; Smith, Brian E.

2010-11-02

Methods, parallel computers, and computer program products are disclosed for low latency, high bandwidth data communications between compute nodes in a parallel computer. Embodiments include receiving, by an origin direct memory access (`DMA`) engine of an origin compute node, data for transfer to a target compute node; sending, by the origin DMA engine of the origin compute node to a target DMA engine on the target compute node, a request to send (`RTS`) message; transferring, by the origin DMA engine, a predetermined portion of the data to the target compute node using memory FIFO operation; determining, by the origin DMA engine whether an acknowledgement of the RTS message has been received from the target DMA engine; if the an acknowledgement of the RTS message has not been received, transferring, by the origin DMA engine, another predetermined portion of the data to the target compute node using a memory FIFO operation; and if the acknowledgement of the RTS message has been received by the origin DMA engine, transferring, by the origin DMA engine, any remaining portion of the data to the target compute node using a direct put operation.

Engine starting apparatus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, D.; Zahlan, M.M.

1992-02-11

This patent describes a starting apparatus for cranking an internal combustion engine. It comprises: an electric cranking motor, s shaft connected to the armature of the cranking motor, a ring gear connected to the engine, a pin which is adapted to be mashed with the ring gear of the engine, a speed responsive clutch connected between the pinion and the shaft for connecting and disconnecting the shaft and pinion, the clutch comprising a first clutch member connected to the shaft to rotate therewith and a second clutch member connected to the pinion, the second clutch member having a portion thereofmore » disposed within the first clutch member, at least one weight member connected to the first clutch member by means which permits the weight member to move radially inwardly toward or radially outwardly away from the portion of the second clutch member, and a spring for urging the weight member radially inwardly into clutching engagement with the portion of the second clutch member, the force of the spring being such as to maintain the weight member in clutching engagement with the portion of the second clutch member when the engine is being cranked the cranking motor at cranking speed.« less

SPDE/SPRE final summary report

NASA Technical Reports Server (NTRS)

Dochat, George

1993-01-01

Mechanical Technology Incorporated (MTI) performed acceptance testing on the Space Power Research Engine (SPRE), which demonstrated satisfactory operation and sufficient reliability for delivery to NASA Lewis Research Center. The unit produced 13.5 kW PV power with an efficiency of 22 percent versus design goals of 28.8 kW PV power and efficiency of 28 percent. Maximum electric power was only 8 kWe due to lower alternator efficiency. One of the major shortcomings of the SPRE was linear alternator efficiency, which was only 70 percent compared to a design value of 90 percent. It was determined from static tests that the major cause for the efficiency shortfall was the location of the magnetic structure surrounding the linear alternator. Testing of an alternator configuration without a surrounding magnetic structure on a linear dynamometer confirmed earlier static test results. Linear alternator efficiency improved from 70 percent to over 90 percent. Testing of the MTI SPRE was also performed with hydrodynamic bearings and achieved full-stroke, stable operation. This testing indicated that hydrodynamic bearings may be useful in free piston Stirling engines. An important factor in achieving stable operation at design stroke was isolating a portion of the bearing length from the engine pressure variations. In addition, the heat pipe heater head design indicates that integration of a Stirling engine with a heat source can be performed via heat pipes. This design provides a baseline against which alternative designs can be measured.

Programmable rate modem utilizing digital signal processing techniques

NASA Technical Reports Server (NTRS)

Bunya, George K.; Wallace, Robert L.

1989-01-01

The engineering development study to follow was written to address the need for a Programmable Rate Digital Satellite Modem capable of supporting both burst and continuous transmission modes with either binary phase shift keying (BPSK) or quadrature phase shift keying (QPSK) modulation. The preferred implementation technique is an all digital one which utilizes as much digital signal processing (DSP) as possible. Here design tradeoffs in each portion of the modulator and demodulator subsystem are outlined, and viable circuit approaches which are easily repeatable, have low implementation losses and have low production costs are identified. The research involved for this study was divided into nine technical papers, each addressing a significant region of concern in a variable rate modem design. Trivial portions and basic support logic designs surrounding the nine major modem blocks were omitted. In brief, the nine topic areas were: (1) Transmit Data Filtering; (2) Transmit Clock Generation; (3) Carrier Synthesizer; (4) Receive AGC; (5) Receive Data Filtering; (6) RF Oscillator Phase Noise; (7) Receive Carrier Selectivity; (8) Carrier Recovery; and (9) Timing Recovery.

Multilayer Insulation Ascent Venting Model

NASA Technical Reports Server (NTRS)

Tramel, R. W.; Sutherlin, S. G.; Johnson, W. L.

2017-01-01

The thermal and venting transient experienced by tank-applied multilayer insulation (MLI) in the Earth-to-orbit environment is very dynamic and not well characterized. This new predictive code is a first principles-based engineering model which tracks the time history of the mass and temperature (internal energy) of the gas in each MLI layer. A continuum-based model is used for early portions of the trajectory while a kinetic theory-based model is used for the later portions of the trajectory, and the models are blended based on a reference mean free path. This new capability should improve understanding of the Earth-to-orbit transient and enable better insulation system designs for in-space cryogenic propellant systems.

Mid-section of a can-annular gas turbine engine with a radial air flow discharged from the compressor section

DOE Office of Scientific and Technical Information (OSTI.GOV)

Little, David A.; McQuiggan, Gerard; Wasdell, David L.

A midframe portion (213) of a gas turbine engine (210) is presented, and includes a compressor section (212) configured to discharge an air flow (211) directed in a radial direction from an outlet of the compressor section (212). Additionally, the midframe portion (213) includes a manifold (214) to directly couple the air flow (211) from the compressor section (212) outlet to an inlet of a respective combustor head (218) of the midframe portion (213).

Design of object-oriented distributed simulation classes

NASA Technical Reports Server (NTRS)

Schoeffler, James D. (Principal Investigator)

1995-01-01

Distributed simulation of aircraft engines as part of a computer aided design package is being developed by NASA Lewis Research Center for the aircraft industry. The project is called NPSS, an acronym for 'Numerical Propulsion Simulation System'. NPSS is a flexible object-oriented simulation of aircraft engines requiring high computing speed. It is desirable to run the simulation on a distributed computer system with multiple processors executing portions of the simulation in parallel. The purpose of this research was to investigate object-oriented structures such that individual objects could be distributed. The set of classes used in the simulation must be designed to facilitate parallel computation. Since the portions of the simulation carried out in parallel are not independent of one another, there is the need for communication among the parallel executing processors which in turn implies need for their synchronization. Communication and synchronization can lead to decreased throughput as parallel processors wait for data or synchronization signals from other processors. As a result of this research, the following have been accomplished. The design and implementation of a set of simulation classes which result in a distributed simulation control program have been completed. The design is based upon MIT 'Actor' model of a concurrent object and uses 'connectors' to structure dynamic connections between simulation components. Connectors may be dynamically created according to the distribution of objects among machines at execution time without any programming changes. Measurements of the basic performance have been carried out with the result that communication overhead of the distributed design is swamped by the computation time of modules unless modules have very short execution times per iteration or time step. An analytical performance model based upon queuing network theory has been designed and implemented. Its application to realistic configurations has not been carried out.

Design of Object-Oriented Distributed Simulation Classes

NASA Technical Reports Server (NTRS)

Schoeffler, James D.

1995-01-01

Distributed simulation of aircraft engines as part of a computer aided design package being developed by NASA Lewis Research Center for the aircraft industry. The project is called NPSS, an acronym for "Numerical Propulsion Simulation System". NPSS is a flexible object-oriented simulation of aircraft engines requiring high computing speed. It is desirable to run the simulation on a distributed computer system with multiple processors executing portions of the simulation in parallel. The purpose of this research was to investigate object-oriented structures such that individual objects could be distributed. The set of classes used in the simulation must be designed to facilitate parallel computation. Since the portions of the simulation carried out in parallel are not independent of one another, there is the need for communication among the parallel executing processors which in turn implies need for their synchronization. Communication and synchronization can lead to decreased throughput as parallel processors wait for data or synchronization signals from other processors. As a result of this research, the following have been accomplished. The design and implementation of a set of simulation classes which result in a distributed simulation control program have been completed. The design is based upon MIT "Actor" model of a concurrent object and uses "connectors" to structure dynamic connections between simulation components. Connectors may be dynamically created according to the distribution of objects among machines at execution time without any programming changes. Measurements of the basic performance have been carried out with the result that communication overhead of the distributed design is swamped by the computation time of modules unless modules have very short execution times per iteration or time step. An analytical performance model based upon queuing network theory has been designed and implemented. Its application to realistic configurations has not been carried out.

A strategy for reducing turnaround time in design optimization using a distributed computer system

NASA Technical Reports Server (NTRS)

Young, Katherine C.; Padula, Sharon L.; Rogers, James L.

1988-01-01

There is a need to explore methods for reducing lengthly computer turnaround or clock time associated with engineering design problems. Different strategies can be employed to reduce this turnaround time. One strategy is to run validated analysis software on a network of existing smaller computers so that portions of the computation can be done in parallel. This paper focuses on the implementation of this method using two types of problems. The first type is a traditional structural design optimization problem, which is characterized by a simple data flow and a complicated analysis. The second type of problem uses an existing computer program designed to study multilevel optimization techniques. This problem is characterized by complicated data flow and a simple analysis. The paper shows that distributed computing can be a viable means for reducing computational turnaround time for engineering design problems that lend themselves to decomposition. Parallel computing can be accomplished with a minimal cost in terms of hardware and software.

Technicians Manufacture a Nozzle for the Kiwi B-1-B Engine

NASA Image and Video Library

1964-05-21

Technicians manufacture a nozzle for the Kiwi B-1-B nuclear rocket engine in the Fabrication Shop’s vacuum oven at the National Aeronautics and Space Administration (NASA) Lewis Research Center. The Nuclear Engine for Rocket Vehicle Applications (NERVA) was a joint NASA and Atomic Energy Commission (AEC) endeavor to develop a nuclear-powered rocket for both long-range missions to Mars and as a possible upper-stage for the Apollo Program. The early portion of the program consisted of basic reactor and fuel system research. This was followed by a series of Kiwi reactors built to test basic nuclear rocket principles in a non-flying nuclear engine. The next phase, NERVA, would create an entire flyable engine. The final phase of the program, called Reactor-In-Flight-Test, would be an actual launch test. The AEC was responsible for designing the nuclear reactor and overall engine. NASA Lewis was responsible for developing the liquid-hydrogen fuel system. The turbopump, which pumped the fuels from the storage tanks to the engine, was the primary tool for restarting the engine. The NERVA had to be able to restart in space on its own using a safe preprogrammed startup system. Lewis researchers endeavored to design and test this system. This non-nuclear Kiwi engine, seen here, was being prepared for tests at Lewis’ High Energy Rocket Engine Research Facility (B-1) located at Plum Brook Station. The tests were designed to start an unfueled Kiwi B-1-B reactor and its Aerojet Mark IX turbopump without any external power.

Light Water Reactor Sustainability Program: Risk-Informed Safety Margins Characterization (RISMC) Pathway Technical Program Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Curtis; Rabiti, Cristian; Martineau, Richard

Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). As the current Light Water Reactor (LWR) NPPs age beyond 60 years, there are possibilities for increased frequency of Systems, Structures, and Components (SSCs) degradations or failures that initiate safety-significant events, reduce existing accident mitigation capabilities, or create new failure modes. Plant designers commonly “over-design” portions of NPPs and provide robustness in the form of redundant and diverse engineered safety features to ensure that, even in the case of well-beyond design basis scenarios, public health and safety will be protected with a very high degreemore » of assurance. This form of defense-in-depth is a reasoned response to uncertainties and is often referred to generically as “safety margin.” Historically, specific safety margin provisions have been formulated, primarily based on “engineering judgment.”« less

A Status Report on the Parachute Development for NASA's Next Manned Spacecraft

NASA Technical Reports Server (NTRS)

Sinclair, Robert

2008-01-01

NASA has determined that the parachute portion of the Landing System for the Crew Exploration Vehicle (CEV) will be Government Furnished Equipment (GFE). The Earth Landing System has been designated CEV Parachute Assembly System (CPAS). Thus a program team was developed consisting of NASA Johnson Space Center (JSC) and Jacobs Engineering through their Engineering and Science Contract Group (ESCG). Following a rigorous competitive phase, Airborne Systems North America was selected to provide the parachute design, testing and manufacturing role to support this team. The development program has begun with some early flight testing of a Generation 1 parachute system. Future testing will continue to refine the design and complete a qualification phase prior to manned flight of the spacecraft. The program team will also support early spacecraft system testing, including a Pad Abort Flight Test in the Fall of 2008

General view of a Space Shuttle Main Engine (SSME) mounted ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General view of a Space Shuttle Main Engine (SSME) mounted on an SSME engine handler, taken in the SSME Processing Facility at Kennedy Space Center. The most prominent features of the engine assembly in this view are the Low-Pressure Fuel Turbopump Discharge Duct looping around the right side and underneath the assembly, the High-Pressure Fuel Turbopump located on the lower left portion of the assembly, the Engine Controller and Main Fuel Valve Hydraulic Actuator located on the upper portion of the assembly and the Low-Pressure Oxidizer Turbopump Discharge Duct at the top of the engine assembly in this view. - Space Transportation System, Space Shuttle Main Engine, Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Convoluted nozzle design for the RL10 derivative 2B engine

NASA Technical Reports Server (NTRS)

1985-01-01

The convoluted nozzle is a conventional refractory metal nozzle extension that is formed with a portion of the nozzle convoluted to show the extendible nozzle within the length of the rocket engine. The convoluted nozzle (CN) was deployed by a system of four gas driven actuators. For spacecraft applications the optimum CN may be self-deployed by internal pressure retained, during deployment, by a jettisonable exit closure. The convoluted nozzle is included in a study of extendible nozzles for the RL10 Engine Derivative 2B for use in an early orbit transfer vehicle (OTV). Four extendible nozzle configurations for the RL10-2B engine were evaluated. Three configurations of the two position nozzle were studied including a hydrogen dump cooled metal nozzle and radiation cooled nozzles of refractory metal and carbon/carbon composite construction respectively.

Air Force Civil Engineer, Volume 16, Number 1, 2008

DTIC Science & Technology

2008-01-01

concrete pavements at any U.S. Air...34 OUT-TO-OUT OF CONCRETE 1’-3" TYP #6 REBAR , TYP, OVERLAP 4’ #6 REBAR , SPACED 15" 3" M IN CO VE R DRILL AND EPOXY COAT WITH OIL PRIOR TO CONCRETE ... concrete portion of the job. The entire project was designed with concrete of varying depths, reinforced with #5 rebar on 1-foot centers.

Space Processing Applications Rocket (SPAR) project SPAR 7

NASA Technical Reports Server (NTRS)

Poorman, R. M.

1983-01-01

The postflight reports of each of the Principal Investigators of three selected science payloads are presented in addition to the engineering report as documented by the Marshall Space Flight Center (MSFC). Pertinent portions of ground-based research leading to the ultimate selection of the flight sample composition are described including design, fabrication and testing. Containerless processing technology, containerless processing bubble dynamics, and comparative alloy solidification are the experiments discussed.

Forward velocity effects on fan noise and the influence of inlet aeroacoustic design as measured in the NASA Ames 40 x 80 foot wind tunnel

NASA Technical Reports Server (NTRS)

Holm, R. G.; Langenbrunner, L. E.; Mccann, E. O.

1981-01-01

The inlet radiated noise of a turbofan engine was studied. The principal research objectives were to characterize or suppress such noise with particular regard to its tonal characteristics. The major portion of this research was conducted by using ground-based static testing without simulation of aircraft forward speed or aircraft installation-related aeroacoustic effects.

Battery thermal management unit

NASA Astrophysics Data System (ADS)

Sanders, Nicholas A.

1989-03-01

A battery warming device has been designed which uses waste heat from an operating internal combustion engine to warm a battery. A portion of the waste heat is stored in the sensible and latent heat of a phase change type material for use in maintaining the battery temperature after the engine is shut off. The basic design of the device consists of a Phase Change Material (PCM) reservoir and a simple heat exchanger connected to the engineer's cooling system. Two types of units were built, tested and field trialed. A strap-on type which was strapped to the side of an automotive battery and was intended for the automotive after-market and a tray type on which a battery or batteries sat. This unit was intended for the heavy duty truck market. It was determined that both types of units increased the average cranking power of the batteries they were applied to. Although there were several design problems with the units such as the need for an automatic thermostatically controlled bypass valve, the overall feeling is that there is a market opportunity for both the strap-on and tray type battery warming units.

Thermal hydraulic-severe accident code interfaces for SCDAP/RELAP5/MOD3.2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coryell, E.W.; Siefken, L.J.; Harvego, E.A.

1997-07-01

The SCDAP/RELAP5 computer code is designed to describe the overall reactor coolant system thermal-hydraulic response, core damage progression, and fission product release during severe accidents. The code is being developed at the Idaho National Engineering Laboratory under the primary sponsorship of the Office of Nuclear Regulatory Research of the U.S. Nuclear Regulatory Commission. The code is the result of merging the RELAP5, SCDAP, and COUPLE codes. The RELAP5 portion of the code calculates the overall reactor coolant system, thermal-hydraulics, and associated reactor system responses. The SCDAP portion of the code describes the response of the core and associated vessel structures.more » The COUPLE portion of the code describes response of lower plenum structures and debris and the failure of the lower head. The code uses a modular approach with the overall structure, input/output processing, and data structures following the pattern established for RELAP5. The code uses a building block approach to allow the code user to easily represent a wide variety of systems and conditions through a powerful input processor. The user can represent a wide variety of experiments or reactor designs by selecting fuel rods and other assembly structures from a range of representative core component models, and arrange them in a variety of patterns within the thermalhydraulic network. The COUPLE portion of the code uses two-dimensional representations of the lower plenum structures and debris beds. The flow of information between the different portions of the code occurs at each system level time step advancement. The RELAP5 portion of the code describes the fluid transport around the system. These fluid conditions are used as thermal and mass transport boundary conditions for the SCDAP and COUPLE structures and debris beds.« less

Ion Engine Plume Interaction Calculations for Prototypical Prometheus 1

NASA Technical Reports Server (NTRS)

Mandell, Myron J.; Kuharski, Robert A.; Gardner, Barbara M.; Katz, Ira; Randolph, Tom; Dougherty, Ryan; Ferguson, Dale C.

2005-01-01

Prometheus 1 is a conceptual mission to demonstrate the use of atomic energy for distant space missions. The hypothetical spacecraft design considered in this paper calls for multiple ion thrusters, each with considerably higher beam energy and beam current than have previously flown in space. The engineering challenges posed by such powerful thrusters relate not only to the thrusters themselves, but also to designing the spacecraft to avoid potentially deleterious effects of the thruster plumes. Accommodation of these thrusters requires good prediction of the highest angle portions of the main beam, as well as knowledge of clastically scattered and charge exchange ions, predictions for grid erosion and contamination of surfaces by eroded grid material, and effects of the plasma plume on radio transmissions. Nonlinear interactions of multiple thrusters are also of concern. In this paper we describe two- and three-dimensional calculations for plume structure and effects of conceptual Prometheus 1 ion engines. Many of the techniques used have been validated by application to ground test data for the NSTAR and NEXT ion engines. Predictions for plume structure and possible sputtering and contamination effects will be presented.

Guidance, navigation, and control subsystem equipment selection algorithm using expert system methods

NASA Technical Reports Server (NTRS)

Allen, Cheryl L.

1991-01-01

Enhanced engineering tools can be obtained through the integration of expert system methodologies and existing design software. The application of these methodologies to the spacecraft design and cost model (SDCM) software provides an improved technique for the selection of hardware for unmanned spacecraft subsystem design. The knowledge engineering system (KES) expert system development tool was used to implement a smarter equipment section algorithm than that which is currently achievable through the use of a standard data base system. The guidance, navigation, and control subsystems of the SDCM software was chosen as the initial subsystem for implementation. The portions of the SDCM code which compute the selection criteria and constraints remain intact, and the expert system equipment selection algorithm is embedded within this existing code. The architecture of this new methodology is described and its implementation is reported. The project background and a brief overview of the expert system is described, and once the details of the design are characterized, an example of its implementation is demonstrated.

Advanced Stirling Radioisotope Generator Engineering Unit 2 (ASRG EU2) Final Assembly

NASA Technical Reports Server (NTRS)

Oriti, Salvatore M.

2015-01-01

NASA Glenn Research Center (GRC) has recently completed the assembly of a unique Stirling generator test article for laboratory experimentation. Under the Advanced Stirling Radioisotope Generator (ASRG) flight development contract, NASA GRC initiated a task to design and fabricate a flight-like generator for in-house testing. This test article was given the name ASRG Engineering Unit 2 (EU2) as it was effectively the second engineering unit to be built within the ASRG project. The intent of the test article was to duplicate Lockheed Martin's qualification unit ASRG design as much as possible to enable system-level tests not previously possible at GRC. After the cancellation of the ASRG flight development project, the decision was made to continue the EU2 build, and make use of a portion of the hardware from the flight development project. GRC and Lockheed Martin engineers collaborated to develop assembly procedures, leveraging the valuable knowledge gathered by Lockheed Martin during the ASRG development contract. The ASRG EU2 was then assembled per these procedures at GRC with Lockheed Martin engineers on site. The assembly was completed in August 2014. This paper details the components that were used for the assembly, and the assembly process itself.

Performance of a transpiration-regenerative cooled rocket thrust chamber

NASA Technical Reports Server (NTRS)

Valler, H. W.

1979-01-01

The analysis, design, fabrication, and testing of a liquid rocket engine thrust chamber which is gas transpiration cooled in the high heat flux convergent portion of the chamber and water jacket cooled (simulated regenerative) in the barrel and divergent sections of the chamber are described. The engine burns LOX-hydrogen propellants at a chamber pressure of 600 psia. Various transpiration coolant flow rates were tested with resultant local hot gas wall temperatures in the 800 F to 1400 F range. The feasibility of transpiration cooling with hydrogen and helium, and the use of photo-etched copper platelets for heat transfer and coolant metering was successfully demonstrated.

Engine and method for operating an engine

DOEpatents

Lauper, Jr., John Christian; Willi, Martin Leo [Dunlap, IL; Thirunavukarasu, Balamurugesh [Peoria, IL; Gong, Weidong [Dunlap, IL

2008-12-23

A method of operating an engine is provided. The method may include supplying a combustible combination of reactants to a combustion chamber of the engine, which may include supplying a first hydrocarbon fuel, hydrogen fuel, and a second hydrocarbon fuel to the combustion chamber. Supplying the second hydrocarbon fuel to the combustion chamber may include at least one of supplying at least a portion of the second hydrocarbon fuel from an outlet port that discharges into an intake system of the engine and supplying at least a portion of the second hydrocarbon fuel from an outlet port that discharges into the combustion chamber. Additionally, the method may include combusting the combustible combination of reactants in the combustion chamber.

Ceramic tile expansion engine housing

DOEpatents

Myers, Blake

1995-01-01

An expandable ceramic tile housing for a high temperature engine is disclosed wherein each tile is independently supported in place in an interlocking matrix by retention mechanisms which mechanically couple the individual ceramic tiles to an outer metal support housing while maintaining thermal isolation of the metal housing from the ceramic tiles. The ceramic tiles are formed with either an octagonal front face portion and a square shank portion or a square front face portion with an octagonal shank portion. The length of the sides of the octagonal front face portion on one tile is equal to the length of the sides of the square front face portion of adjoining tiles to permit formation of an interlocking matrix. Fibrous ceramic sealing material may be placed between radial and tangential facing surfaces of adjacent tiles to limit radial gas flow therebetween. Labyrinth-sealed pressure-controlled compartments may be established between the tile housing and the outer metal support housing to control radial gas flow.

Ceramic tile expansion engine housing

DOEpatents

Myers, B.

1995-04-11

An expandable ceramic tile housing for a high temperature engine is disclosed wherein each tile is independently supported in place in an interlocking matrix by retention mechanisms which mechanically couple the individual ceramic tiles to an outer metal support housing while maintaining thermal isolation of the metal housing from the ceramic tiles. The ceramic tiles are formed with either an octagonal front face portion and a square shank portion or a square front face portion with an octagonal shank portion. The length of the sides of the octagonal front face portion on one tile is equal to the length of the sides of the square front face portion of adjoining tiles to permit formation of an interlocking matrix. Fibrous ceramic sealing material may be placed between radial and tangential facing surfaces of adjacent tiles to limit radial gas flow there between. Labyrinth-sealed pressure-controlled compartments may be established between the tile housing and the outer metal support housing to control radial gas flow. 8 figures.

Apparatus and filtering systems relating to combustors in combustion turbine engines

DOEpatents

Johnson, Thomas Edward [Greer, SC; Zuo, Baifang [Simpsonville, SC; Stevenson, Christian Xavier [Inman, SC

2012-03-27

A combustor for a combustion turbine engine that includes: a chamber defined by an outer wall and forming a channel between windows defined through the outer wall toward a forward end of the chamber and at least one fuel injector positioned toward an aft end of the chamber; and a multilayer screen filter comprising at least two layers of screen over at least a portion of the windows and at least one layer of screen over the remaining portion of the windows. The windows include a forward end and a forward portion, and an aft end and an aft portion. The multilayer screen filter is positioned over the windows such that, in operation, a supply of compressed air entering the chamber through the windows passes through at least one layer of screen. The multilayer screen filter is configured such that the aft portion of the windows include at least two layers of screen, and the forward portion of the windows includes one less layer of screen than the aft portion of the windows.

Acoustic measurements in a jet engine test facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, V.R.

1982-01-01

The US Air Force has had problems with aircraft engine noise generated during ground run-up. These operations have resulted in many community complaints and serious restrictions being placed on ground run-up activity which affected training and fleet readiness. A program of noise abatement was undertaken to suppress ground run-up noise. The original designs included water-cooled noise suppressors which were peculiar to a single aircraft. This made each usable only with the aircraft for which it was designed. Noise surveys indicated that the close-coupled suppressor did not address the problem of noise radiated from unenclosed portions of the fuselage. To alleviatemore » this situation, the approach adopted was to use a complete aircraft enclosure, called a hush house, and a large augmenter tube which is totally air-cooled.« less

Hypersonic CFD applications for the National Aero-Space Plane

NASA Technical Reports Server (NTRS)

Richardson, Pamela F.; Mcclinton, Charles R.; Bittner, Robert D.; Dilley, A. Douglas; Edwards, Kelvin W.

1989-01-01

Design and analysis of the NASP depends heavily upon developing the critical technology areas that cover the entire engineering design of the vehicle. These areas include materials, structures, propulsion systems, propellants, integration of airframe and propulsion systems, controls, subsystems, and aerodynamics areas. Currently, verification of many of the classical engineering tools relies heavily on computational fluid dynamics. Advances are being made in the development of CFD codes to accomplish nose-to-tail analyses for hypersonic aircraft. Additional details involving the partial development, analysis, verification, and application of the CFL3D code and the SPARK combustor code are discussed. A nonequilibrium version of CFL3D that is presently being developed and tested is also described. Examples are given of portion calculations for research hypersonic aircraft geometries and comparisons with experiment data show good agreement.

Pre-mixing apparatus for a turbine engine

DOEpatents

Lacy, Benjamin Paul [Greer, SC; Varatharajan, Balachandar [Cincinnati, OH; Ziminsky, Willy Steve [Simpsonville, SC; Kraemer, Gilbert Otto [Greer, SC; Yilmaz, Ertan [Albany, NY; Melton, Patrick Benedict [Horse Shoe, NC; Zuo, Baifang [Simpsonville, SC; Stevenson, Christian Xavier [Inman, SC; Felling, David Kenton [Greenville, SC; Uhm, Jong Ho [Simpsonville, SC

2012-04-03

A pre-mixing apparatus for a turbine engine includes a main body having an inlet portion, an outlet portion and an exterior wall that collectively establish at least one fluid delivery plenum, and a plurality of fluid delivery tubes extending through at least a portion of the at least one fluid delivery plenum. Each of the plurality of fluid delivery tubes includes at least one fluid delivery opening fluidly connected to the at least one fluid delivery plenum. With this arrangement, a first fluid is selectively delivered to the at least one fluid delivery plenum, passed through the at least one fluid delivery opening and mixed with a second fluid flowing through the plurality of fluid delivery tubes prior to being combusted in a combustion chamber of a turbine engine.

Deep Space 1 is prepared for transport to launch pad

NASA Technical Reports Server (NTRS)

1998-01-01

In the Defense Satellite Communications Systems Processing Facility (DPF), Cape Canaveral Air Station (CCAS), after covering the lower portion of Deep Space 1, workers adjust the anti-static blanket covering the upper portion. The blanket will protect the spacecraft during transport to the launch pad. Deep Space 1 is the first flight in NASA's New Millennium Program, and is designed to validate 12 new technologies for scientific space missions of the next century, including the engine. Propelled by the gas xenon, the engine is being flight-tested for future deep space and Earth-orbiting missions. Deceptively powerful, the ion drive emits only an eerie blue glow as ionized atoms of xenon are pushed out of the engine. While slow to pick up speed, over the long haul it can deliver 10 times as much thrust per pound of fuel as liquid or solid fuel rockets. Other onboard experiments include software that tracks celestial bodies so the spacecraft can make its own navigation decisions without the intervention of ground controllers. Deep Space 1 will complete most of its mission objectives within the first two months, but will also do a flyby of a near-Earth asteroid, 1992 KD, in July 1999. Deep Space 1 will be launched aboard a Boeing Delta 7326 rocket from Launch Pad 17A, CCAS.

KSC-98pc1316

NASA Image and Video Library

1998-10-10

KENNEDY SPACE CENTER, FLA. -- In the Defense Satellite Communications Systems Processing Facility (DPF), Cape Canaveral Air Station (CCAS), after covering the lower portion of Deep Space 1, workers adjust the anti-static blanket covering the upper portion. The blanket will protect the spacecraft during transport to the launch pad. Deep Space 1 is the first flight in NASA's New Millennium Program, and is designed to validate 12 new technologies for scientific space missions of the next century, including the engine. Propelled by the gas xenon, the engine is being flight-tested for future deep space and Earth-orbiting missions. Deceptively powerful, the ion drive emits only an eerie blue glow as ionized atoms of xenon are pushed out of the engine. While slow to pick up speed, over the long haul it can deliver 10 times as much thrust per pound of fuel as liquid or solid fuel rockets. Other onboard experiments include software that tracks celestial bodies so the spacecraft can make its own navigation decisions without the intervention of ground controllers. Deep Space 1 will complete most of its mission objectives within the first two months, but will also do a flyby of a near-Earth asteroid, 1992 KD, in July 1999. Deep Space 1 will be launched aboard a Boeing Delta 7326 rocket from Launch Pad 17A, CCAS

Engineering plant metabolism into microbes: from systems biology to synthetic biology.

PubMed

Xu, Peng; Bhan, Namita; Koffas, Mattheos A G

2013-04-01

Plant metabolism represents an enormous repository of compounds that are of pharmaceutical and biotechnological importance. Engineering plant metabolism into microbes will provide sustainable solutions to produce pharmaceutical and fuel molecules that could one day replace substantial portions of the current fossil-fuel based economy. Metabolic engineering entails targeted manipulation of biosynthetic pathways to maximize yields of desired products. Recent advances in Systems Biology and the emergence of Synthetic Biology have accelerated our ability to design, construct and optimize cell factories for metabolic engineering applications. Progress in predicting and modeling genome-scale metabolic networks, versatile gene assembly platforms and delicate synthetic pathway optimization strategies has provided us exciting opportunities to exploit the full potential of cell metabolism. In this review, we will discuss how systems and synthetic biology tools can be integrated to create tailor-made cell factories for efficient production of natural products and fuel molecules in microorganisms. Copyright © 2012 Elsevier Ltd. All rights reserved.

System for cooling hybrid vehicle electronics, method for cooling hybrid vehicle electronics

DOEpatents

France, David M.; Yu, Wenhua; Singh, Dileep; Zhao, Weihuan

2017-11-21

The invention provides a single radiator cooling system for use in hybrid electric vehicles, the system comprising a surface in thermal communication with electronics, and subcooled boiling fluid contacting the surface. The invention also provides a single radiator method for simultaneously cooling electronics and an internal combustion engine in a hybrid electric vehicle, the method comprising separating a coolant fluid into a first portion and a second portion; directing the first portion to the electronics and the second portion to the internal combustion engine for a time sufficient to maintain the temperature of the electronics at or below 175.degree. C.; combining the first and second portion to reestablish the coolant fluid; and treating the reestablished coolant fluid to the single radiator for a time sufficient to decrease the temperature of the reestablished coolant fluid to the temperature it had before separation.

Thin-film module circuit design: Practical and reliability aspects

NASA Technical Reports Server (NTRS)

Daiello, R. V.; Twesme, E. N.

1985-01-01

This paper will address several aspects of the design and construction of submodules based on thin film amorphous silicon (a-Si) p i n solar cells. Starting from presently attainable single cell characteristics, and a realistic set of specifications, practical module designs are discussed from the viewpoints of efficient designs, the fabrication requirements, and reliability concerns. The examples center mostly on series interconnected modules of the superstrate type with detailed discussions of each portion of the structure in relation to its influence on module efficiency. Emphasis is placed on engineering topics such as: area coverage, optimal geometries, and cost and reliability. Practical constraints on achieving optimal designs, along with some examples of potential pitfalls in the manufacture and subsequent performance of a-Si modules are discussed.

Durability and Life of Ceramic Matrix Composites in Combustion Environment

NASA Technical Reports Server (NTRS)

Tewari, Surendra

1997-01-01

It is now generally recognized that the next frontier in the commercial air travel will be achieved by an optimum combination of the concepts being used for the air and space transports. It will depend upon the new engines specifically designed to meet the demanding strength, temperature, environment and economy requirements. The successful development of an advanced propulsion system for a 21st Century High Speed Civil Transport will require key advances in the combustor system. Minimizing nitrous oxide (NO(x)) emission is critical, since the deleterious interaction within the ozone layer would occur at the proposed vehicle cruise level of about 75,000 feet. In order to achieve the low NOx levels an efficient combustor operating at controlled equivalence ratios and high combustion temperatures are required. This requires a combustor, whose one portion will be operating in an oxidizing environment while the other portion will operate in a reducing environment. This rather unusual requirement has introduced considerable challenge to the materials scientists and engineers, the development of material systems capable of long-life at high temperatures (up to 3000 F) in an oxidizing and/or reducing environment.

In-line wear monitor. Final report, July 1988-April 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pieper, K.A.; Taylor, I.J.

This report describes construction and test results of an in-line monitor for critical ferrous and nonferrous metal debris in turbine engine lubrication systems. The in-line wear monitor (ILWM) uses the X-ray fluorescence principle for detecting metal debris on a continuous basis while the engine is running. The sensor portion of the system is engine mounted and contains a radioactive X-ray source, a flow cell to direct the oil across an X-ray permeable window, a proportional counter X-ray detector and its associated preamplifier and amplifier electronics. The data acquisition electronics is mounted on the airframe and contains a microprocessor based systemmore » for inputting pulses from the sensor, classifying and counting them according to energy bands, and analyzing the data and outputting metal concentration values to the engine monitoring system. The sensor portion of the system is designed to fit on a TF41 turbine engine in place of a tube between the oil tank and the oil pump. A TF41 engine monitoring system has been modified to accept the new signals from the ILWM on spare inputs so that none of the existing functions were disturbed. The ILWM has been flow tested at various flow rates, concentration levels, oil temperatures, and aerations. The wear monitor detected iron, copper, and both iron and copper together with less than 2 ppm one sigma statistical uncertainty for 30 minute count times over the 0-50 ppm range. There was no significant effect of flow rate or aeration on accuracy. The system is developed to the point that it can be tested in an actual flight environment.« less

14 CFR 23.1192 - Engine accessory compartment diaphragm.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine accessory compartment diaphragm. 23... Powerplant Powerplant Fire Protection § 23.1192 Engine accessory compartment diaphragm. For aircooled radial engines, the engine power section and all portions of the exhaust sytem must be isolated from the engine...

14 CFR 25.1192 - Engine accessory section diaphragm.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Engine accessory section diaphragm. 25.1192....1192 Engine accessory section diaphragm. For reciprocating engines, the engine power section and all portions of the exhaust system must be isolated from the engine accessory compartment by a diaphragm that...

14 CFR 25.1192 - Engine accessory section diaphragm.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Engine accessory section diaphragm. 25.1192....1192 Engine accessory section diaphragm. For reciprocating engines, the engine power section and all portions of the exhaust system must be isolated from the engine accessory compartment by a diaphragm that...

14 CFR 23.1192 - Engine accessory compartment diaphragm.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Engine accessory compartment diaphragm. 23... Powerplant Powerplant Fire Protection § 23.1192 Engine accessory compartment diaphragm. For aircooled radial engines, the engine power section and all portions of the exhaust sytem must be isolated from the engine...

14 CFR 23.1192 - Engine accessory compartment diaphragm.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Engine accessory compartment diaphragm. 23... Powerplant Powerplant Fire Protection § 23.1192 Engine accessory compartment diaphragm. For aircooled radial engines, the engine power section and all portions of the exhaust sytem must be isolated from the engine...

14 CFR 25.1192 - Engine accessory section diaphragm.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine accessory section diaphragm. 25.1192....1192 Engine accessory section diaphragm. For reciprocating engines, the engine power section and all portions of the exhaust system must be isolated from the engine accessory compartment by a diaphragm that...

An overview of engineering concepts and current design algorithms for probabilistic structural analysis

NASA Technical Reports Server (NTRS)

Duffy, S. F.; Hu, J.; Hopkins, D. A.

1995-01-01

The article begins by examining the fundamentals of traditional deterministic design philosophy. The initial section outlines the concepts of failure criteria and limit state functions two traditional notions that are embedded in deterministic design philosophy. This is followed by a discussion regarding safety factors (a possible limit state function) and the common utilization of statistical concepts in deterministic engineering design approaches. Next the fundamental aspects of a probabilistic failure analysis are explored and it is shown that deterministic design concepts mentioned in the initial portion of the article are embedded in probabilistic design methods. For components fabricated from ceramic materials (and other similarly brittle materials) the probabilistic design approach yields the widely used Weibull analysis after suitable assumptions are incorporated. The authors point out that Weibull analysis provides the rare instance where closed form solutions are available for a probabilistic failure analysis. Since numerical methods are usually required to evaluate component reliabilities, a section on Monte Carlo methods is included to introduce the concept. The article concludes with a presentation of the technical aspects that support the numerical method known as fast probability integration (FPI). This includes a discussion of the Hasofer-Lind and Rackwitz-Fiessler approximations.

Engineering Trade-off Considerations Regarding Design-for-Security, Design-for-Verification, and Design-for-Test

NASA Technical Reports Server (NTRS)

Berg, Melanie; Label, Kenneth

2018-01-01

The United States government has identified that application specific integrated circuit (ASIC) and field programmable gate array (FPGA) hardware are at risk from a variety of adversary attacks. This finding affects system security and trust. Consequently, processes are being developed for system mitigation and countermeasure application. The scope of this tutorial pertains to potential vulnerabilities and countermeasures within the ASIC/FPGA design cycle. The presentation demonstrates how design practices can affect the risk for the adversary to: change circuitry, steal intellectual property, and listen to data operations. An important portion of the design cycle is assuring the design is working as specified or as expected. This is accomplished by exhaustive testing of the target design. Alternatively, it has been shown that well established schemes for test coverage enhancement (design-for-verification (DFV) and design-for-test (DFT)) can create conduits for adversary accessibility. As a result, it is essential to perform a trade between robust test coverage versus reliable design implementation. The goal of this tutorial is to explain the evolution of design practices; review adversary accessibility points due to DFV and DFT circuitry insertion (back door circuitry); and to describe common engineering trade-off considerations for test versus adversary threats.

Rivers, Rockets and Readiness: Army Engineers in the Sunbelt

DTIC Science & Technology

1979-01-01

at Proctor Lake. 138 Water sports are enjoyed at Benbrook Lake. 139 The powerhouse at Sam Rayburn Dam and Reservoir. 140 Amistad Dam - a...for the Fort Worth District. Th~ Fort Worth District designed the United States portion of the Amistad Dam--a cooperative effort with Mexico on the...Antonio Resident Office.17 Adding to the workload was the Amistad Dam located on the Rio Grande River about twelve miles above Del Rio, Texas. The

Friction of Aviation Engines

NASA Technical Reports Server (NTRS)

Sparrow, S W; Thorne, M A

1928-01-01

The first portion of this report discusses measurements of friction made in the altitude laboratory of the Bureau of Standards between 1920 and 1926 under research authorization of the National Advisory Committee for Aeronautics. These are discussed with reference to the influence of speed, barometric pressure, jacket-water temperature, and throttle opening upon the friction of aviation engines. The second section of the report deals with measurements of the friction of a group of pistons differing from each other in a single respect, such as length, clearance, area of thrust face, location of thrust face, etc. Results obtained with each type of piston are discussed and attention is directed particularly to the fact that the friction chargeable to piston rings depends upon piston design as well as upon ring design. This is attributed to the effect of the rings upon the thickness and distribution of the oil film which in turn affects the friction of the piston to an extent which depends upon its design.

76 FR 24923 - National Science Board; Sunshine Act Meetings; Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-03

...: Some portions open, some portions closed. UPDATES: Please refer to the National Science Board Web site... Information Item: Status Deep Underground Science and Engineering Laboratory Information Item: High...

Systems and method for delivering liquified gas to an engine

DOEpatents

Bingham, Dennis N.; Wilding, Bruce M.; O'Brien, James E.; Siahpush, Ali S.; Brown, Kevin B.

2002-01-01

A liquified gas delivery system for a motorized platform includes a holding tank configured to receive liquified gas. A first conduit extends from a vapor holding portion of the tank to a valve device. A second conduit extends from a liquid holding portion of the tank to the valve device. Fluid coupled to the valve device is a vaporizer which is in communication with an engine. The valve device selectively withdraws either liquified gas or liquified gas vapor from the tank depending on the pressure within the vapor holding portion of the tank. Various configurations of the delivery system can be utilized for pressurizing the tank during operation.

Methods For Delivering Liquified Gas To An Engine

DOEpatents

Bingham, Dennis N.; Wilding, Bruce M.; O'Brien, James E.; Siahpush, Ali S.; Brown, Kevin B.

2003-09-16

A liquified gas delivery system for a motorized platform includes a holding tank configured to receive liquified gas. A first conduit extends from a vapor holding portion of the tank to a valve device. A second conduit extends from a liquid holding portion of the tank to the valve device. Fluid coupled to the valve device is a vaporizer which is in communication with an engine. The valve device selectively withdraws either liquified gas or liquified gas vapor from the tank depending on the pressure within the vapor holding portion of the tank. Various configurations of the delivery system can be utilized for pressurizing the tank during operation.

Methods For Delivering Liquified Gas To An Engine

DOEpatents

Bingham, Dennis N.; Wilding, Bruce M.; O'Brien, James E.; Siahpush, Ali S.; Brown, Kevin B.

2005-10-11

A liquified gas delivery system for a motorized platform includes a holding tank configured to receive liquified gas. A first conduit extends from a vapor holding portion of the tank to a valve device. A second conduit extends from a liquid holding portion of the tank to the valve device. Fluid coupled to the valve device is a vaporizer which is in communication with an engine. The valve device selectively withdraws either liquified gas or liquified gas vapor from the tank depending on the pressure within the vapor holding portion of the tank. Various configurations of the delivery system can be utilized for pressurizing the tank during operation.

Systems for delivering liquified gas to an engine

DOEpatents

Bingham, Dennis N.; Wilding, Bruce M.; O'Brien, James E.; Siahpush, Ali S.; Brown, Kevin B.

2006-05-16

A liquified gas delivery system for a motorized platform includes a holding tank configured to receive liquified gas. A first conduit extends from a vapor holding portion of the tank to a valve device. A second conduit extends from a liquid holding portion of the tank to the valve device. Fluid coupled to the valve device is a vaporizer which is in communication with an engine. The valve device selectively withdraws either liquified gas or liquified gas vapor from the tank depending on the pressure within the vapor holding portion of the tank. Various configurations of the delivery system can be utilized for pressurizing the tank during operation.

Rolling contact mounting arrangement for a ceramic combustor

DOEpatents

Boyd, G.L.; Shaffer, J.E.

1995-10-17

A combustor assembly having a preestablished rate of thermal expansion is mounted within a gas turbine engine housing having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the combustor assembly. The combustor assembly is constructed of a inlet end portion, a outlet end portion and a plurality of combustor ring segments positioned between the end portions. A mounting assembly is positioned between the combustor assembly and the gas turbine engine housing to allow for the difference in the rate of thermal expansion while maintaining axially compressive force on the combustor assembly to maintain contact between the separate components. 3 figs.

Rolling contact mounting arrangement for a ceramic combustor

DOEpatents

Boyd, Gary L.; Shaffer, James E.

1995-01-01

A combustor assembly having a preestablished rate of thermal expansion is mounted within a gas turbine engine housing having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the combustor assembly. The combustor assembly is constructed of a inlet end portion, a outlet end portion and a plurality of combustor ring segments positioned between the end portions. A mounting assembly is positioned between the combustor assembly and the gas turbine engine housing to allow for the difference in the rate of thermal expansion while maintaining axially compressive force on the combustor assembly to maintain contact between the separate components.

Computational Assessment of the Benefits of Boundary Layer Ingestion for the D8 Aircraft

NASA Technical Reports Server (NTRS)

Pandya, Shishir A.; Uranga, Alejandra

2013-01-01

To substantially reduce the fuel burn of future commercial transportation aircraft, the boundary layer ingestion idea is investigated. The idea is that an engine placed in the wake of the aircraft it is propelling is more efficient than a conventional engine placement under the wing or on pods mounted to the rear of the fuselage. The top, rear of the fuselage is thus designed to act as a diffuser such that the engines can be placed there with a minimal nacelle. The boundary layer thickens over the rear of the fuselage such that a large portion of it is ingested by the fan. To assess whether the boundary layer ingesting (BLI) engine placement is indeed advantageous, a study of the nacelle aerodynamics is carried out using Overflow, a viscous CFD flow solver that uses overset meshes. The computed forces and moments are compared to a wind tunnel experiment for validation. Some aspects of the design are verified using the simulation results. Finally, the effect of the nacelle placement is assessed by comparing the BLI nacelle configuration to a podded nacelle configuration and to the unpowered (without nacelles) aircraft.

Model-Based Systems Engineering for Capturing Mission Architecture System Processes with an Application Case Study - Orion Flight Test 1

NASA Technical Reports Server (NTRS)

Bonanne, Kevin H.

2011-01-01

Model-based Systems Engineering (MBSE) is an emerging methodology that can be leveraged to enhance many system development processes. MBSE allows for the centralization of an architecture description that would otherwise be stored in various locations and formats, thus simplifying communication among the project stakeholders, inducing commonality in representation, and expediting report generation. This paper outlines the MBSE approach taken to capture the processes of two different, but related, architectures by employing the Systems Modeling Language (SysML) as a standard for architecture description and the modeling tool MagicDraw. The overarching goal of this study was to demonstrate the effectiveness of MBSE as a means of capturing and designing a mission systems architecture. The first portion of the project focused on capturing the necessary system engineering activities that occur when designing, developing, and deploying a mission systems architecture for a space mission. The second part applies activities from the first to an application problem - the system engineering of the Orion Flight Test 1 (OFT-1) End-to-End Information System (EEIS). By modeling the activities required to create a space mission architecture and then implementing those activities in an application problem, the utility of MBSE as an approach to systems engineering can be demonstrated.

Development of OTM Syngas Process and Testing of Syngas Derived Ultra-clean Fuels in Diesel Engines and Fuel Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

E.T.; James P. Meagher; Prasad Apte

2002-12-31

This topical report summarizes work accomplished for the Program from November 1, 2001 to December 31, 2002 in the following task areas: Task 1: Materials Development; Task 2: Composite Development; Task 4: Reactor Design and Process Optimization; Task 8: Fuels and Engine Testing; 8.1 International Diesel Engine Program; 8.2 Nuvera Fuel Cell Program; and Task 10: Program Management. Major progress has been made towards developing high temperature, high performance, robust, oxygen transport elements. In addition, a novel reactor design has been proposed that co-produces hydrogen, lowers cost and improves system operability. Fuel and engine testing is progressing well, but wasmore » delayed somewhat due to the hiatus in program funding in 2002. The Nuvera fuel cell portion of the program was completed on schedule and delivered promising results regarding low emission fuels for transportation fuel cells. The evaluation of ultra-clean diesel fuels continues in single cylinder (SCTE) and multiple cylinder (MCTE) test rigs at International Truck and Engine. FT diesel and a BP oxygenate showed significant emissions reductions in comparison to baseline petroleum diesel fuels. Overall through the end of 2002 the program remains under budget, but behind schedule in some areas.« less

25. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. ELEVATIONS, RIGHT AND LEFT PORTIONS, TEST CELLS 5-12. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

24. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. ELEVATIONS, CENTRAL PORTION AND TEST CELLS 1-4. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

26. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. CROSS-SECTION, CENTRAL PORTION AND TEST CELLS 1-4. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

29. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. 19508 RENOVATION OF FIRST FLOOR, CENTRAL PORTION. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

NGST Yardstick Integrated Science Instrument Module (ISIM) Feasibility Study

NASA Astrophysics Data System (ADS)

Greenhouse, M. A.; Dipirro, M.; Federline, B.; Gardner, Jonathan P.; Guy, P.; Hagopian, J.; Hein, J.; Jurotich, M.; Lawrence, J.; Martineau, B.; Mather, J. C.; Mentzell, E.; Satyapal, S.; Stanley, D.; Teplitz, H. I.; Travis, J.; Bely, P.; Petro, L. D.; Stockman, P.; Burg, R.; Bitzel, R.

1998-12-01

We display portions of the baseline design concept for the NGST Integrated Science Instrument Module (ISIM). This ISIM design is under ongoing development for integration with the "Yardstick" and other NGST 8 m architectures that are intended for packaging in an EELV or Ariane 5 meter class fairing. The goals of this activity are to: [1] demonstrate mission science feasibility, [2] identify ISIM technology challenge areas, [3] assess ISIM engineering and cost feasibility, [5] identify ISIM/NGST interface constraints, and [6] enable smart customer procurement of the ISIM. In this poster, we display a snap shot of work in progress including: optical design, opto-mechanical layout, thermal modeling, focal plane array design, and electronics design. Ongoing progress can be monitored via ISIM team web site: http://ngst.gsfc.nasa.gov/

14. Drawing showing stress for central viaduct, Walworth Run portion ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. Drawing showing stress for central viaduct, Walworth Run portion 1885. Drawing courtesy Engineering Department, City of Cleveland. - Abbey Avenue Viaduct, Spanning Walworth Valley at Abbey Avenue, Cleveland, Cuyahoga County, OH

Engine balance apparatus and accessory drive device

NASA Technical Reports Server (NTRS)

Egleston, Robert W. (Inventor)

2002-01-01

A balancing mechanism for an engine that has a rotating crankshaft and reciprocating pistons. The balancing mechanism comprises a primary balance mass assembly non-rotatably and removably affixed to the crankshaft. The primary mass assembly comprises a primary mass affixed to a primary hub portion and a primary cap portion removably affixed to the primary hub portion to clamp a portion of the crankshaft therebetween. A secondary balance mass assembly may be rotatably and removably supported on the crankshaft. A driver assembly is affixed to the crankshaft to cause the secondary balance mass to rotate in a direction that is opposite to the direction in which the crank shaft is rotating. The driver assembly may include auxiliary gears configured to transport rotary power to auxiliary components. The gears are readily detachable from the apparatus to facilitate inspection and repair operations.

Combustion diagnostic for active engine feedback control

DOEpatents

Green, Jr., Johney Boyd; Daw, Charles Stuart; Wagner, Robert Milton

2007-10-02

This invention detects the crank angle location where combustion switches from premixed to diffusion, referred to as the transition index, and uses that location to define integration limits that measure the portions of heat released during the combustion process that occur during the premixed and diffusion phases. Those integrated premixed and diffusion values are used to develop a metric referred to as the combustion index. The combustion index is defined as the integrated diffusion contribution divided by the integrated premixed contribution. As the EGR rate is increased enough to enter the low temperature combustion regime, PM emissions decrease because more of the combustion process is occurring over the premixed portion of the heat release rate profile and the diffusion portion has been significantly reduced. This information is used to detect when the engine is or is not operating in a low temperature combustion mode and provides that feedback to an engine control algorithm.

Fuel Efficiency Mapping of a 2014 6-Cylinder GM EcoTec 4.3L Engine with Cylinder Deactivation (SAE 2016-01-0662)

EPA Science Inventory

This paper describes the method and test results of the engine dyno portion of the benchmarking test results including engine fuel consumption maps showing the effects of cylinder deactivation engine technology.

Houma Navigation Canal Deepening Project Terrebonne Parish, Louisiana: Cultural Resources Literature Search, Records Review and Research Design

DTIC Science & Technology

2005-03-01

have Louisiana now leads the nation in the loss of its often subsided completely beneath the marsh. wetlands and in coastal erosion. Erosion of its...western portions of the wetlands . The Isles Dernieries, for example, have study area, but their distribution has changed over the highest rate of coastal...Orleans District, U.S. Army Corps of 1973 Louisiana Canals and Their Influence on Engineers. Wetland Development. Ph.D. dissertation, Louisiana State

Repair of the Czar Shaft sinkhole

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deatherage, J.D.; Starkey, J.; Gustavson, N.

1996-12-31

After a Portion of the Queen Mine parking lot collapsed into a sinkhole, an engineering study was conducted to confirm that the cause of the damage was settlement into the Czar Shaft in Bisbee, Arizona. Historical records were researched to describe and locate the original shaft, and a seismic refraction survey was performed to define the foundation conditions within and around the shaft. Recommended mitigation measures were developed to repair the parking lot. Mitigation included design and construction of a flexible geosynthetic cap and telltale settlement monitoring system.

21. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. SECOND FLOOR PLAN, RIGHT AND LEFT END PORTIONS, TEST CELLS 5-12. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

18. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

18. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. FIRST FLOOR PLAN, CENTRAL PORTION AND TEST CELLS 1-4. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

27. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. CROSS-SECTION, RIGHT AND LEFT END PORTIONS, TEST CELLS 5-12. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

22. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. THIRD FLOOR AND ROOF PLAN, CENTRAL PORTION AND TEST CELLS 1-4. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

16. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. BASEMENT FLOOR PLAN, CENTRAL PORTION AND TEST CELLS 1-4. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

17. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. BASEMENT FLOOR PLAN, RIGHT AND LEFT END PORTIONS, TEST CELLS 5-12. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

20. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. SECOND FLOOR PLAN, CENTRAL PORTION AND TEST CELLS 1-4. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

19. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. FIRST FLOOR PLAN, RIGHT AND LEFT END PORTIONS, TEST CELLS 5-12. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

Stirling cycle engine and refrigeration systems

NASA Technical Reports Server (NTRS)

Higa, W. H. (Inventor)

1976-01-01

A Stirling cycle heat engine is disclosed in which displacer motion is controlled as a function of the working fluid pressure P sub 1 and a substantially constant pressure P sub 0. The heat engine includes an auxiliary chamber at the constant pressure P sub 0. An end surface of a displacer piston is disposed in the auxiliary chamber. During the compression portion of the engine cycle when P sub 1 rises above P sub 0 the displacer forces the working fluid to pass from the cold chamber to the hot chamber of the engine. During the expansion portion of the engine cycle the heated working fluid in the hot chamber does work by pushing down on the engine's drive piston. As the working fluid pressure P sub 1 drops below P sub 0 the displacer forces most of the working fluid in the hot chamber to pass through the regenerator to the cold chamber. The engine is easily combinable with a refrigeration section to provide a refrigeration system in which the engine's single drive piston serves both the engine and the refrigeration section.

Impact resistance of composite fan blades

NASA Technical Reports Server (NTRS)

1974-01-01

Results are presented of a program to determine the impact resistance of composite fan blades subjected to foreign object damage (FOD) while operating under conditions simulating a short take-off and landing (STOL) engine at takeoff. The full-scale TF39 first-stage fan blade was chosen as the base design for the demonstration component since its configuration and operating tip speeds are similar to a typical STOL fan blade several composite configurations had already been designed and evaluated under previous programs. The first portion of the program was devoted toward fabricating and testing high impact resistant, aerodynamically acceptable composite blades which utilized only a single material system in any given blade. In order to increase the blade impact capability beyond this point, several mixed material (hybrid) designs were investigated using S-glass and Kevlar as well as boron and graphite fibers. These hybrid composite blades showed a marked improvement in resistance to bird impact over those blades made of a single composite material. The work conducted under this program has demonstrated substantial improvement in composite fan blades with respect to FOD resistance and has indicated that the hybrid design concept, which utilizes different types of fibers in various portions of a fan blade design depending on the particular requirements of the different areas and the characteristics of the different fibers involved, shows a significant improvement over those designs utilizing only one material system.

Field Programmable Gate Array Reliability Analysis Guidelines for Launch Vehicle Reliability Block Diagrams

NASA Technical Reports Server (NTRS)

Al Hassan, Mohammad; Britton, Paul; Hatfield, Glen Spencer; Novack, Steven D.

2017-01-01

Field Programmable Gate Arrays (FPGAs) integrated circuits (IC) are one of the key electronic components in today's sophisticated launch and space vehicle complex avionic systems, largely due to their superb reprogrammable and reconfigurable capabilities combined with relatively low non-recurring engineering costs (NRE) and short design cycle. Consequently, FPGAs are prevalent ICs in communication protocols and control signal commands. This paper will identify reliability concerns and high level guidelines to estimate FPGA total failure rates in a launch vehicle application. The paper will discuss hardware, hardware description language, and radiation induced failures. The hardware contribution of the approach accounts for physical failures of the IC. The hardware description language portion will discuss the high level FPGA programming languages and software/code reliability growth. The radiation portion will discuss FPGA susceptibility to space environment radiation.

Interactive calculation procedures for mixed compression inlets

NASA Technical Reports Server (NTRS)

Reshotko, Eli

1983-01-01

The proper design of engine nacelle installations for supersonic aircraft depends on a sophisticated understanding of the interactions between the boundary layers and the bounding external flows. The successful operation of mixed external-internal compression inlets depends significantly on the ability to closely control the operation of the internal compression portion of the inlet. This portion of the inlet is one where compression is achieved by multiple reflection of oblique shock waves and weak compression waves in a converging internal flow passage. However weak these shocks and waves may seem gas-dynamically, they are of sufficient strength to separate a laminar boundary layer and generally even strong enough for separation or incipient separation of the turbulent boundary layers. An understanding was developed of the viscous-inviscid interactions and of the shock wave boundary layer interactions and reflections.

32 CFR 644.372 - Care and custody through interim use.

Code of Federal Regulations, 2011 CFR

2011-07-01

... maintenance and restoration as required by standard Corps of Engineers lease forms. Where a portion of an... the portion leased. The Economy Act may not apply in some cases where industrial plants are determined...

32 CFR 644.372 - Care and custody through interim use.

Code of Federal Regulations, 2010 CFR

2010-07-01

... maintenance and restoration as required by standard Corps of Engineers lease forms. Where a portion of an... the portion leased. The Economy Act may not apply in some cases where industrial plants are determined...

Fuel nozzle assembly for use in turbine engines and methods of assembling same

DOEpatents

Uhm, Jong Ho; Johnson, Thomas Edward

2015-02-03

A fuel nozzle for use with a turbine engine is described herein. The fuel nozzle includes a housing that is coupled to a combustor liner defining a combustion chamber. The housing includes an endwall that at least partially defines the combustion chamber. A plurality of mixing tubes extends through the housing for channeling fuel to the combustion chamber. Each mixing tube of the plurality of mixing tubes includes an inner surface that extends between an inlet portion and an outlet portion. The outlet portion is oriented adjacent the housing endwall. At least one of the plurality of mixing tubes includes a plurality of projections that extend outwardly from the outlet portion. Adjacent projections are spaced a circumferential distance apart such that a groove is defined between each pair of circumferentially-apart projections to facilitate enhanced mixing of fuel in the combustion chamber.

Researcher Poses with a Nuclear Rocket Model

NASA Image and Video Library

1961-11-21

A researcher at the NASA Lewis Research Center with slide ruler poses with models of the earth and a nuclear-propelled rocket. The Nuclear Engine for Rocket Vehicle Applications (NERVA) was a joint NASA and Atomic Energy Commission (AEC) endeavor to develop a nuclear-powered rocket for both long-range missions to Mars and as a possible upper-stage for the Apollo Program. The early portion of the program consisted of basic reactor and fuel system research. This was followed by a series of Kiwi reactors built to test nuclear rocket principles in a non-flying nuclear engine. The next phase, NERVA, would create an entire flyable engine. The AEC was responsible for designing the nuclear reactor and overall engine. NASA Lewis was responsible for developing the liquid-hydrogen fuel system. The nuclear rocket model in this photograph includes a reactor at the far right with a hydrogen propellant tank and large radiator below. The payload or crew would be at the far left, distanced from the reactor.

Gas turbine engine with supersonic compressor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, II, William Byron; Lawlor, Shawn P.

A gas turbine engine having a compressor section using blades on a rotor to deliver a gas at supersonic conditions to a stator. The stator includes one or more of aerodynamic ducts that have converging and diverging portions for deceleration of the gas to subsonic conditions and to deliver a high pressure gas to combustors. The aerodynamic ducts include structures for changing the effective contraction ratio to enable starting even when designed for high pressure ratios, and structures for boundary layer control. In an embodiment, aerodynamic ducts are provided having an aspect ratio of two to one (2:1) or more,more » when viewed in cross-section orthogonal to flow direction at an entrance to the aerodynamic duct.« less

The Texas Remote Sensing Training Project

NASA Technical Reports Server (NTRS)

Wells, J. B.

1975-01-01

The project was designed to train federal, state and regional agency managers, scientists and engineers. A one-week seminar was designed and implemented to build vocabulary, introduce technical subject areas and give students enough training to allow them to relate remote sensing technology to operational agency projects. The seminar was designed to perform the dual function of conveying enough remote sensing information to be of value as a stand-alone and preparing students for detailed pattern recognition training. The LARSYS III portion of the training project was executed exactly as designed in the LARSYS training materials package; the LARSYS package did not contain a LANDSAT training module. Two LANDSAT training modules were developed using Texas LANDSAT data. One module contained central Texas data and the second module contained coastal zone data.

45 CFR 13.7 - Studies, exhibits, analyses, engineering reports, tests and projects.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 1 2011-10-01 2011-10-01 false Studies, exhibits, analyses, engineering reports... Studies, exhibits, analyses, engineering reports, tests and projects. The reasonable cost (or the reasonable portion of the cost) for any study, exhibit, analysis, engineering report, test, project or...

45 CFR 13.7 - Studies, exhibits, analyses, engineering reports, tests and projects.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 45 Public Welfare 1 2013-10-01 2013-10-01 false Studies, exhibits, analyses, engineering reports... Studies, exhibits, analyses, engineering reports, tests and projects. The reasonable cost (or the reasonable portion of the cost) for any study, exhibit, analysis, engineering report, test, project or...

45 CFR 13.7 - Studies, exhibits, analyses, engineering reports, tests and projects.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 45 Public Welfare 1 2014-10-01 2014-10-01 false Studies, exhibits, analyses, engineering reports... Studies, exhibits, analyses, engineering reports, tests and projects. The reasonable cost (or the reasonable portion of the cost) for any study, exhibit, analysis, engineering report, test, project or...

45 CFR 13.7 - Studies, exhibits, analyses, engineering reports, tests and projects.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Studies, exhibits, analyses, engineering reports... Studies, exhibits, analyses, engineering reports, tests and projects. The reasonable cost (or the reasonable portion of the cost) for any study, exhibit, analysis, engineering report, test, project or...

45 CFR 13.7 - Studies, exhibits, analyses, engineering reports, tests and projects.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 45 Public Welfare 1 2012-10-01 2012-10-01 false Studies, exhibits, analyses, engineering reports... Studies, exhibits, analyses, engineering reports, tests and projects. The reasonable cost (or the reasonable portion of the cost) for any study, exhibit, analysis, engineering report, test, project or...

Whole-cell biocomputing

NASA Technical Reports Server (NTRS)

Simpson, M. L.; Sayler, G. S.; Fleming, J. T.; Applegate, B.

2001-01-01

The ability to manipulate systems on the molecular scale naturally leads to speculation about the rational design of molecular-scale machines. Cells might be the ultimate molecular-scale machines and our ability to engineer them is relatively advanced when compared with our ability to control the synthesis and direct the assembly of man-made materials. Indeed, engineered whole cells deployed in biosensors can be considered one of the practical successes of molecular-scale devices. However, these devices explore only a small portion of cellular functionality. Individual cells or self-organized groups of cells perform extremely complex functions that include sensing, communication, navigation, cooperation and even fabrication of synthetic nanoscopic materials. In natural systems, these capabilities are controlled by complex genetic regulatory circuits, which are only partially understood and not readily accessible for use in engineered systems. Here, we focus on efforts to mimic the functionality of man-made information-processing systems within whole cells.

Gasket with pushrod retainer

DOEpatents

Knudsen, Julian R.; Welch, Christopher B.

2005-04-26

In an engine having a rocker member adapted to rock about an axis intermediate the rocker member and a pushrod extending from a lower body to an upper body and engaging an end of the rocker member, a gasket for sealing the lower body to the upper body is provided. The gasket includes a sealing portion adapted to substantially seal at least a portion of the upper body to the lower body, and a pushrod support portion extending outwardly from the sealing portion adapted to engage the pushrod. At least a portion of the pushrod support portion engaging the pushrod is constructed from a material that is softer than the material of the pushrod.

23. Photocopy of engineering drawing, May, 1941 (original drawing located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. Photocopy of engineering drawing, May, 1941 (original drawing located at Fairchild Air Force Base, Civil Engineering Building, Civil Engineering vault). ENGINE TEST CELL BUILDING. THIRD FLOOR AND ROOF PLAN, RIGHT AND LEFT END PORTIONS, TEST CELLS 5-12. - Fairchild Air Force Base, Engine Test Cell Building, Near intersection of Arnold Street & George Avenue, Spokane, Spokane County, WA

Method and apparatus for reducing cold-phase emissions by utilizing oxygen-enriched intake air

DOEpatents

Poola, Ramesh B.; Sekar, Ramanujam R.; Stork, Kevin C.

1997-01-01

An oxygen-enriched air intake control system for an internal combustion engine includes air directing apparatus to control the air flow into the intake of the engine. During normal operation of the engine, ambient air flowing from an air filter of the engine flows through the air directing apparatus into the intake of the engine. In order to decrease the amount of carbon monoxide (CO) and hydrocarbon (HC) emissions that tend to be produced by the engine during a short period of time after the engine is started, the air directing apparatus diverts for a short period of time following the start up of the engine at least a portion of the ambient air from the air filter through a secondary path. The secondary path includes a selectively permeable membrane through which the diverted portion of the ambient air flows. The selectively permeable membrane separates nitrogen and oxygen from the diverted air so that oxygen enriched air containing from about 23% to 25% oxygen by volume is supplied to the intake of the engine.

Jet engine nozzle exit configurations and associated systems and methods

NASA Technical Reports Server (NTRS)

Mengle, Vinod G. (Inventor)

2011-01-01

Nozzle exit configurations and associated systems and methods are disclosed. An aircraft system in accordance with one embodiment includes a jet engine exhaust nozzle having an internal flow surface and an exit aperture, with the exit aperture having a perimeter that includes multiple projections extending in an aft direction. Aft portions of individual neighboring projections are spaced apart from each other by a gap, and a geometric feature of the multiple can change in a monotonic manner along at least a portion of the perimeter.

Jet Engine Nozzle Exit Configurations and Associated Systems and Methods

NASA Technical Reports Server (NTRS)

Mengle, Vinod G. (Inventor)

2013-01-01

Nozzle exit configurations and associated systems and methods are disclosed. An aircraft system in accordance with one embodiment includes a jet engine exhaust nozzle having an internal flow surface and an exit aperture, with the exit aperture having a perimeter that includes multiple projections extending in an aft direction. Aft portions of individual neighboring projections are spaced apart from each other by a gap, and a geometric feature of the multiple can change in a monotonic manner along at least a portion of the perimeter.

Conceptual design study for Infrared Limb Experiment (IRLE)

NASA Technical Reports Server (NTRS)

Baker, Doran J.; Ulwick, Jim; Esplin, Roy; Batty, J. C.; Ware, Gene; Tew, Craig

1989-01-01

The phase A engineering design study for the Infrared Limb Experiment (IRLE) instrument, the infrared portion of the Mesosphere-Lower Thermosphere Explorer (MELTER) satellite payload is given. The IRLE instrument is a satellite instrument, based on the heritage of the Limb Infrared Monitor of the Stratosphere (LIMS) program, that will make global measurements of O3, CO2, NO, NO2, H2O, and OH from earth limb emissions. These measurements will be used to provide improved understanding of the photochemistry, radiation, dynamics, energetics, and transport phenomena in the lower thermosphere, mesosphere, and stratosphere. The IRLE instrument is the infrared portion of the MELTER satellite payload. MELTER is being proposed to NASA Goddard by a consortium consisting of the University of Michigan, University of Colorado and NASA Langley. It is proposed that the Space Dynamics Laboratory at Utah State University (SDL/USU) build the IRLE instrument for NASA Langley. MELTER is scheduled for launch in November 1994 into a sun-synchronous, 650-km circular orbit with an inclination angle of 97.8 deg and an ascending node at 3:00 p.m. local time.

KSC-2014-2634

NASA Image and Video Library

2014-05-21

CAPE CANAVERAL, Fla. – The judges for the mining portion of NASA's 2014 Robotics Mining Competition are introduced during the opening ceremony at the Kennedy Space Center Visitor Complex in Florida. At far right, on the podium are Rob Mueller, lead technical expert and head judge from Kennedy's Engineering and Technology Directorate, and Kimberley Land, event emcee from NASA's Ames Research Center in Moffett Field, California. More than 35 teams from around the U.S. have designed and built remote-controlled robots for the mining competition. The competition is a NASA Human Exploration and Operations Mission Directorate project designed to engage and retain students in science, technology, engineering and mathematics, or STEM, fields by expanding opportunities for student research and design. Teams use their remote-controlled robotics to maneuver and dig in a supersized sandbox filled with a crushed material that has characteristics similar to Martian soil. The objective of the challenge is to see which team’s robot can collect and move the most regolith within a specified amount of time. For more information, visit www.nasa.gov/nasarmc. Photo credit: NASA/Frankie Martin

Visual illusions and plate design: The effects of plate rim widths and rim coloring on perceived food portion size

PubMed Central

McClain, Arianna; van den Bos, Wouter; Matheson, Donna; Desai, Manisha; McClure, Samuel M.; Robinson, Thomas N.

2013-01-01

OBJECTIVE The Delboeuf Illusion affects perceptions of the relative sizes of concentric shapes. This study was designed to extend research on the application of the Delboeuf illusion to food on a plate by testing whether a plate’s rim width and coloring influence perceptual bias to affect perceived food portion size. DESIGN AND METHODS Within-subjects experimental design. Experiment 1 tested the effect of rim width on perceived food portion size. Experiment 2 tested the effect of rim coloring on perceived food portion size. In both experiments, participants observed a series of photographic images of paired, side-by-side plates varying in designs and amounts of food. From each pair, participants were asked to select the plate that contained more food. Multi-level logistic regression examined the effects of rim width and coloring on perceived food portion size. RESULTS Experiment 1: Participants overestimated the diameter of food portions by 5% and the visual area of food portions by 10% on plates with wider rims compared to plates with very thin rims (P<0.0001). The effect of rim width was greater with larger food portion sizes. Experiment 2: Participants overestimated the diameter of food portions by 1.5% and the visual area of food portions by 3% on plates with rim coloring compared to plates with no coloring (P=0.01). The effect of rim coloring was greater with smaller food portion sizes. CONCLUSION The Delboeuf illusion applies to food on a plate. Participants overestimated food portion size on plates with wider and colored rims. These findings may help design plates to influence perceptions of food portion sizes. PMID:24005858

Boeing B–29 Superfortress at the Aircraft Engine Research Laboratory

NASA Image and Video Library

1944-07-21

A Boeing B–29 Superfortress at the National Advisory Committee for Aeronautics (NACA) Aircraft Engine Research Laboratory in Cleveland, Ohio. The B–29 was the Army Air Forces’ deadliest weapon during the latter portion of World War II. The aircraft was significantly larger than previous bombers but could fly faster and higher. The B–29 was intended to soar above anti-aircraft fire and make pinpoint drops onto strategic targets. The bomber was forced to carry 20,000 pounds more armament than it was designed for. The extra weight pushed the B–29’s four powerful Wright R–3350 engines to their operating limits. The over-heating of the engines proved to be a dangerous problem. The military asked the NACA to tackle the issue. Full-scale engine tests on a R–3350 engine in the Prop House demonstrated that a NACA-designed impeller increased the flow rate of the fuel injection system. Altitude Wind Tunnel studies of the engine led to the reshaping of cowling inlet and outlet to improve airflow and reduce drag. Single-cylinder studies on valve failures were resolved by a slight extension of the cylinder head, and the Engine Research Building researchers combated uneven heating with a new fuel injection system. The modifications were then tried out on an actual B–29. The bomber arrived in Cleveland on June 22, 1944. The new injection impeller, ducted head baffles and instrumentation were installed on the bomber’s two left wing engines. Eleven test flights were flown over the next month with military pilots at the helm. Overall the flight tests corroborated the wind tunnel and test stand studies.

Section 508 Electronic Information Accessibility Requirements for Software Development

NASA Technical Reports Server (NTRS)

Ellis, Rebecca

2014-01-01

Section 508 Subpart B 1194.21 outlines requirements for operating system and software development in order to create a product that is accessible to users with various disabilities. This portion of Section 508 contains a variety of standards to enable those using assistive technology and with visual, hearing, cognitive and motor difficulties to access all information provided in software. The focus on requirements was limited to the Microsoft Windows® operating system as it is the predominant operating system used at this center. Compliance with this portion of the requirements can be obtained by integrating the requirements into the software development cycle early and by remediating issues in legacy software if possible. There are certain circumstances with software that may arise necessitating an exemption from these requirements, such as design or engineering software using dynamically changing graphics or numbers to convey information. These exceptions can be discussed with the Section 508 Coordinator and another method of accommodation used.

Requirements analysis for a hardware, discrete-event, simulation engine accelerator

NASA Astrophysics Data System (ADS)

Taylor, Paul J., Jr.

1991-12-01

An analysis of a general Discrete Event Simulation (DES), executing on the distributed architecture of an eight mode Intel PSC/2 hypercube, was performed. The most time consuming portions of the general DES algorithm were determined to be the functions associated with message passing of required simulation data between processing nodes of the hypercube architecture. A behavioral description, using the IEEE standard VHSIC Hardware Description and Design Language (VHDL), for a general DES hardware accelerator is presented. The behavioral description specifies the operational requirements for a DES coprocessor to augment the hypercube's execution of DES simulations. The DES coprocessor design implements the functions necessary to perform distributed discrete event simulations using a conservative time synchronization protocol.

Visual illusions and plate design: the effects of plate rim widths and rim coloring on perceived food portion size.

PubMed

McClain, A D; van den Bos, W; Matheson, D; Desai, M; McClure, S M; Robinson, T N

2014-05-01

The Delboeuf Illusion affects perceptions of the relative sizes of concentric shapes. This study was designed to extend research on the application of the Delboeuf illusion to food on a plate by testing whether a plate's rim width and coloring influence perceptual bias to affect perceived food portion size. Within-subjects experimental design. Experiment 1 tested the effect of rim width on perceived food portion size. Experiment 2 tested the effect of rim coloring on perceived food portion size. In both experiments, participants observed a series of photographic images of paired, side-by-side plates varying in designs and amounts of food. From each pair, participants were asked to select the plate that contained more food. Multilevel logistic regression examined the effects of rim width and coloring on perceived food portion size. Experiment 1: participants overestimated the diameter of food portions by 5% and the visual area of food portions by 10% on plates with wider rims compared with plates with very thin rims (P<0.0001). The effect of rim width was greater with larger food portion sizes. Experiment 2: participants overestimated the diameter of food portions by 1.5% and the visual area of food portions by 3% on plates with rim coloring compared with plates with no coloring (P=0.01). The effect of rim coloring was greater with smaller food portion sizes. The Delboeuf illusion applies to food on a plate. Participants overestimated food portion size on plates with wider and colored rims. These findings may help design plates to influence perceptions of food portion sizes.

International Dimension in Engineering Education

ERIC Educational Resources Information Center

Borri, C.; Guberti, E.; Melsa, J.

2007-01-01

Engineers of the 21st century will spend appreciable portions of their careers in environments rich with global connections. Therefore, engineering colleges and universities must develop strategies that provide the global perspectives and international experiences that will help their graduates excel in this new world order. The current paper…

Coupled parametric design of flow control and duct shape

NASA Technical Reports Server (NTRS)

Florea, Razvan (Inventor); Bertuccioli, Luca (Inventor)

2009-01-01

A method for designing gas turbine engine components using a coupled parametric analysis of part geometry and flow control is disclosed. Included are the steps of parametrically defining the geometry of the duct wall shape, parametrically defining one or more flow control actuators in the duct wall, measuring a plurality of performance parameters or metrics (e.g., flow characteristics) of the duct and comparing the results of the measurement with desired or target parameters, and selecting the optimal duct geometry and flow control for at least a portion of the duct, the selection process including evaluating the plurality of performance metrics in a pareto analysis. The use of this method in the design of inter-turbine transition ducts, serpentine ducts, inlets, diffusers, and similar components provides a design which reduces pressure losses and flow profile distortions.

40 CFR 86.1336-84 - Engine starting, restarting, and shutdown.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (4) If a failure to start occurs during the hot start portion of the test and is caused by engine... stalling. (1) If the engine stalls during the initial idle period of either the cold or hot start test, the engine shall be restarted immediately using the appropriate cold or hot starting procedure and the test...

40 CFR 86.1336-84 - Engine starting, restarting, and shutdown.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (4) If a failure to start occurs during the hot start portion of the test and is caused by engine... stalling. (1) If the engine stalls during the initial idle period of either the cold or hot start test, the engine shall be restarted immediately using the appropriate cold or hot starting procedure and the test...

40 CFR 86.1336-84 - Engine starting, restarting, and shutdown.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (4) If a failure to start occurs during the hot start portion of the test and is caused by engine... stalling. (1) If the engine stalls during the initial idle period of either the cold or hot start test, the engine shall be restarted immediately using the appropriate cold or hot starting procedure and the test...

Current efforts on developing an HWIL synthetic environment for LADAR sensor testing at AMRDEC

NASA Astrophysics Data System (ADS)

Kim, Hajin J.; Cornell, Michael C.; Naumann, Charles B.

2005-05-01

Efforts in developing a synthetic environment for testing LADAR sensors in a hardware-in-the-loop simulation are continuing at the Aviation and Missile Research, Engineering, and Development Center (AMRDEC) of the U.S. Army Research, Engineering and Development Command (RDECOM). Current activities have concentrated on developing the optical projection hardware portion of the synthetic environment. These activities range from system level design down to component level testing. Of particular interest have been schemes for generating the optical signals representing the individual pixels of the projection. Several approaches have been investigated and tested with emphasis on operating wavelength, intensity dynamic range and uniformity, and flexibility in pixel waveform generation. This paper will discuss some of the results from these current efforts at RDECOM's Advanced Simulation Center (ASC).

Microfog lubrication for aircraft engine bearings

NASA Technical Reports Server (NTRS)

Rosenlieb, J. W.

1976-01-01

An analysis and system study was performed to provide design information regarding lubricant and coolant flow rates and flow paths for effective utilization of the lubricant and coolant in a once through bearing oil mist (microfog) and coolant air system. Both static and dynamic tests were performed. Static tests were executed to evaluate and calibrate the mist supply system. A total of thirteen dynamic step speed bearing tests were performed using four different lubricants and several different mist and air supply configurations. The most effective configuration consisted of supplying the mist and the major portion of the cooling air axially through the bearing. The results of these tests have shown the feasibility of using a once through oil mist and cooling air system to lubricate and cool a high speed, high temperature aircraft engine mainshaft bearing.

NORTHERN PORTION OF WEST ELEVATION OF FUEL STORAGE BUILDING (CPP603). ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTHERN PORTION OF WEST ELEVATION OF FUEL STORAGE BUILDING (CPP-603). PHOTO TAKEN LOOKING NORTHEAST. INL PHOTO NUMBER HD-54-20-4. Mike Crane, Photographer, 8/2005 - Idaho National Engineering Laboratory, Idaho Chemical Processing Plant, Fuel Reprocessing Complex, Scoville, Butte County, ID

NORTHERN PORTION OF WEST ELEVATION OF FUEL STORAGE BUILDING (CPP603). ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTHERN PORTION OF WEST ELEVATION OF FUEL STORAGE BUILDING (CPP-603). PHOTO TAKEN LOOKING SOUTHEAST. INL PHOTO NUMBER HD-54-20-2. Mike Crane, Photographer, 8/2005 - Idaho National Engineering Laboratory, Idaho Chemical Processing Plant, Fuel Reprocessing Complex, Scoville, Butte County, ID

Engine Certification and Compliance Testing

EPA Pesticide Factsheets

The National Vehicle and Fuel Emissions Laboratory (NVFEL) tests a portion of all heavy-duty diesel and small gasoline engines intended for sale in the United States to confirm compliance with EPA’s exhaust emissions standards.

Selection of NIR H2O absorption transitions for in-cylinder measurement of temperature in IC engines

NASA Astrophysics Data System (ADS)

Zhou, Xin; Liu, Xiang; Jeffries, Jay B.; Hanson, Ronald K.

2005-12-01

The water vapour spectrum in the 1.25-1.65 µm region is systematically analysed to find the best absorption transitions for sensitive measurement of in-cylinder gas temperature over short paths in an internal combustion engine. The strategy to select the optimum wavelength regions and absorption line combinations is developed for the time-varying pressures and temperatures expected during the compression portion of an engine cycle. We have identified 14 transitions of water vapour in this spectral region as promising for this application. From these transitions, 16 potential line pairs were considered for a wavelength-modulated absorption sensor for in-cylinder gas temperature during the compression stroke. Expected performance is modelled for the intake portion of two engine cycles that produce extreme temperature and pressure variations during compression.

ViLLaGEs: opto-mechanical design of an on-sky visible-light MEMS-based AO system

NASA Astrophysics Data System (ADS)

Grigsby, Bryant; Lockwood, Chris; Baumann, Brian; Gavel, Don; Johnson, Jess; Ammons, S. Mark; Dillon, Daren; Morzinski, Katie; Reinig, Marc; Palmer, Dave; Severson, Scott; Gates, Elinor

2008-07-01

Visible Light Laser Guidestar Experiments (ViLLaGEs) is a new Micro-Electro Mechanical Systems (MEMS) based visible-wavelength adaptive optics (AO) testbed on the Nickel 1-meter telescope at Lick Observatory. Closed loop Natural Guide Star (NGS) experiments were successfully carried out during engineering during the fall of 2007. This is a major evolutionary step, signaling the movement of AO technologies into visible light with a MEMS mirror. With on-sky Strehls in I-band of greater than 20% during second light tests, the science possibilities have become evident. Described here is the advanced engineering used in the design and construction of the ViLLaGEs system, comparing it to the LickAO infrared system, and a discussion of Nickel dome infrastructural improvements necessary for this system. A significant portion of the engineering discussion revolves around the sizable effort that went towards eliminating flexure. Then, we detail upgrades to ViLLaGEs to make it a facility class instrument. These upgrades will focus on Nyquist sampling the diffraction limited point spread function during open loop operations, motorization and automation for technician level alignments, adding dithering capabilities and changes for near infrared science.

Fuel injector nozzle for an internal combustion engine

DOEpatents

Cavanagh, Mark S [Bloomington, IL; Urven, Jr., Roger L.; Lawrence, Keith E [Peoria, IL

2011-03-22

A direct injection fuel injector includes a nozzle tip having a plurality of passages allowing fluid communication between an inner nozzle tip surface portion and an outer nozzle tip surface portion and directly into a combustion chamber of an internal combustion engine. A first group of the passages have inner surface apertures located substantially in a first common plane. A second group of the passages have inner surface apertures located substantially in at least a second common plane substantially parallel to the first common plane. The second group has more passages than the first group.

Fuel Injector Nozzle For An Internal Combustion Engine

DOEpatents

Cavanagh, Mark S.; Urven, Jr.; Roger L.; Lawrence, Keith E.

2006-04-25

A direct injection fuel injector includes a nozzle tip having a plurality of passages allowing fluid communication between an inner nozzle tip surface portion and an outer nozzle tip surface portion and directly into a combustion chamber of an internal combustion engine. A first group of the passages have inner surface apertures located substantially in a first common plane. A second group of the passages have inner surface apertures located substantially in at least a second common plane substantially parallel to the first common plane. The second group has more passages than the first group.

Fuel injector nozzle for an internal combustion engine

DOEpatents

Cavanagh, Mark S.; Urven, Jr., Roger L.; Lawrence, Keith E.

2007-11-06

A direct injection fuel injector includes a nozzle tip having a plurality of passages allowing fluid communication between an inner nozzle tip surface portion and an outer nozzle tip surface portion and directly into a combustion chamber of an internal combustion engine. A first group of the passages have inner surface apertures located substantially in a first common plane. A second group of the passages have inner surface apertures located substantially in at least a second common plane substantially parallel to the first common plane. The second group has more passages than the first group.

Fuel injector nozzle for an internal combustion engine

DOEpatents

Cavanagh, Mark S.; Urven, Jr., Roger L.; Lawrence, Keith E.

2008-11-04

A direct injection fuel injector includes a nozzle tip having a plurality of passages allowing fluid communication between an inner nozzle tip surface portion and an outer nozzle tip surface portion and directly into a combustion chamber of an internal combustion engine. A first group of the passages have inner surface apertures located substantially in a first common plane. A second group of the passages have inner surface apertures located substantially in at least a second common plane substantially parallel to the first common plane. The second group has more passages than the first group.

Diesel emission reduction using internal exhaust gas recirculation

DOEpatents

He, Xin [Denver, CO; Durrett, Russell P [Bloomfield Hills, MI

2012-01-24

A method for controlling combustion in a direct-injection diesel engine includes monitoring a crankshaft rotational position of a cylinder of the engine, monitoring an engine load, determining an intake stroke within the cylinder based upon the crankshaft rotational position, and when the engine load is less than a threshold engine load, opening an exhaust valve for the cylinder during a portion of the intake stroke.

Variable oxygen/nitrogen enriched intake air system for internal combustion engine applications

DOEpatents

Poola, Ramesh B.; Sekar, Ramanujam R.; Cole, Roger L.

1997-01-01

An air supply control system for selectively supplying ambient air, oxygen enriched air and nitrogen enriched air to an intake of an internal combustion engine includes an air mixing chamber that is in fluid communication with the air intake. At least a portion of the ambient air flowing to the mixing chamber is selectively diverted through a secondary path that includes a selectively permeable air separating membrane device due a differential pressure established across the air separating membrane. The permeable membrane device separates a portion of the nitrogen in the ambient air so that oxygen enriched air (permeate) and nitrogen enriched air (retentate) are produced. The oxygen enriched air and the nitrogen enriched air can be selectively supplied to the mixing chamber or expelled to atmosphere. Alternatively, a portion of the nitrogen enriched air can be supplied through another control valve to a monatomic-nitrogen plasma generator device so that atomic nitrogen produced from the nitrogen enriched air can be then injected into the exhaust of the engine. The oxygen enriched air or the nitrogen enriched air becomes mixed with the ambient air in the mixing chamber and then the mixed air is supplied to the intake of the engine. As a result, the air being supplied to the intake of the engine can be regulated with respect to the concentration of oxygen and/or nitrogen.

14 CFR 25.1182 - Nacelle areas behind firewalls, and engine pod attaching structures containing flammable fluid...

Code of Federal Regulations, 2011 CFR

2011-01-01

... pod attaching structures containing flammable fluid lines. 25.1182 Section 25.1182 Aeronautics and..., and engine pod attaching structures containing flammable fluid lines. (a) Each nacelle area immediately behind the firewall, and each portion of any engine pod attaching structure containing flammable...

14 CFR 25.1182 - Nacelle areas behind firewalls, and engine pod attaching structures containing flammable fluid...

Code of Federal Regulations, 2010 CFR

2010-01-01

... pod attaching structures containing flammable fluid lines. 25.1182 Section 25.1182 Aeronautics and..., and engine pod attaching structures containing flammable fluid lines. (a) Each nacelle area immediately behind the firewall, and each portion of any engine pod attaching structure containing flammable...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

40 CFR 85.1406 - Certification.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-use engine that is newly rebuilt to its original configuration. (b) Diesel test fuel. Federally... used is the heavy-duty engine Federal Test Procedure as set forth in the applicable portions of part 86... provide some level of particulate emission reduction, and will not cause the urban bus engine to fail to...

Menu-engineering in restaurants - adapting portion sizes on plates to enhance vegetable consumption: a real-life experiment.

PubMed

Reinders, Machiel J; Huitink, Marlijn; Dijkstra, S Coosje; Maaskant, Anna J; Heijnen, Joris

2017-12-25

The aim of this research was to investigate whether increased portion sizes of vegetables and decreased portion sizes of meat on main dishes increased the amount of vegetables consumed in a real-life restaurant setting without affecting customer satisfaction. The participants were unaware of the experiment. A cross-over design was used in which three restaurants were randomly assigned to a sequence of an intervention and control condition. In the intervention period, the vegetable portion sizes on the plates of main dishes were doubled (150 g of vegetables instead of 75 g) and the portion sizes of meat on the plates were reduced by an average of 12.5%. In the control period, the portion sizes of the main dishes were maintained as usual. In total, 1006 observations and questionnaires were included. Vegetable consumption from plates was significantly higher during the intervention period (M = 115.5 g) than during the control period (M = 61.7 g). Similarly, total vegetable consumption (including side dishes) was significantly higher during the intervention period (M = 178.0 g) than during the control period (M = 137.0 g). Conversely, meat consumption was significantly lower during the intervention period (M = 183.1 g) than during the control period (M = 211.1 g). Satisfaction with the restaurant visit did not differ between the intervention period (M = 1.27) and control period (M = 1.35). Satisfaction with the main dish was significantly lower during the intervention period (M = 1.25) than during the control period (M = 1.38), although in both cases, the scores indicated that participants remained (very) satisfied with their main dish. This study showed that increasing vegetable portions in combination with decreasing meat portions (unknowingly to the consumer) increased the amount of vegetables consumed and decreased the amount of meat consumed. Furthermore, despite the changes in portion sizes, participants remained satisfied with their restaurant visit and main dish. The findings of this study suggest that modifying portion size in restaurants is an effective tool for stimulating vegetable consumption and consequently healthy and sustainable diets.

Laboratory Design for Microbiological Safety

PubMed Central

Phillips, G. Briggs; Runkle, Robert S.

1967-01-01

Of the large amount of funds spent each year in this country on construction and remodeling of biomedical research facilities, a significant portion is directed to laboratories handling infectious microorganisms. This paper is intended for the scientific administrators, architects, and engineers concerned with the design of new microbiological facilities. It develops and explains the concept of primary and secondary barriers for the containment of microorganisms. The basic objectives of a microbiological research laboratory, (i) protection of the experimenter and staff, (ii) protection of the surrounding community, and (iii) maintenance of experimental validity, are defined. In the design of a new infectious-disease research laboratory, early identification should be made of the five functional zones of the facility and their relation to each other. The following five zones and design criteria applicable to each are discussed: clean and transition, research area, animal holding and research area, laboratory support, engineering support. The magnitude of equipment and design criteria which are necessary to integrate these five zones into an efficient and safe facility are delineated. Images Fig. 1 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig. 18 Fig. 19 PMID:4961771

Evolutionary Design and Simulation of a Tube Crawling Inspection Robot

NASA Technical Reports Server (NTRS)

Craft, Michael; Howsman, Tom; ONeil, Daniel; Howell, Joe T. (Technical Monitor)

2002-01-01

The Space Robotics Assembly Team Simulation (SpaceRATS) is an expansive concept that will hopefully lead to a space flight demonstration of a robotic team cooperatively assembling a system from its constitutive parts. A primary objective of the SpaceRATS project is to develop a generalized evolutionary design approach for multiple classes of robots. The portion of the overall SpaceRats program associated with the evolutionary design and simulation of an inspection robot's morphology is the subject of this paper. The vast majority of this effort has concentrated on the use and modification of Darwin2K, a robotic design and simulation software package, to analyze the design of a tube crawling robot. This robot is designed for carrying out inspection duties in relatively inaccessible locations within a liquid rocket engine similar to the SSME. A preliminary design of the tube crawler robot was completed, and the mechanical dynamics of the system were simulated. An evolutionary approach to optimizing a few parameters of the system was utilized, resulting in a more optimum design.

QFD-ANP Approach for the Conceptual Design of Research Vessels: A Case Study

NASA Astrophysics Data System (ADS)

Venkata Subbaiah, Kambagowni; Yeshwanth Sai, Koneru; Suresh, Challa

2016-10-01

Conceptual design is a subset of concept art wherein a new idea of product is created instead of a visual representation which would directly be used in a final product. The purpose is to understand the needs of conceptual design which are being used in engineering designs and to clarify the current conceptual design practice. Quality function deployment (QFD) is a customer oriented design approach for developing new or improved products and services to enhance customer satisfaction. House of quality (HOQ) has been traditionally used as planning tool of QFD which translates customer requirements (CRs) into design requirements (DRs). Factor analysis is carried out in order to reduce the CR portions of HOQ. The analytical hierarchical process is employed to obtain the priority ratings of CR's which are used in constructing HOQ. This paper mainly discusses about the conceptual design of an oceanographic research vessel using analytical network process (ANP) technique. Finally the QFD-ANP integrated methodology helps to establish the importance ratings of DRs.

ECO fill: automated fill modification to support late-stage design changes

NASA Astrophysics Data System (ADS)

Davis, Greg; Wilson, Jeff; Yu, J. J.; Chiu, Anderson; Chuang, Yao-Jen; Yang, Ricky

2014-03-01

One of the most critical factors in achieving a positive return for a design is ensuring the design not only meets performance specifications, but also produces sufficient yield to meet the market demand. The goal of design for manufacturability (DFM) technology is to enable designers to address manufacturing requirements during the design process. While new cell-based, DP-aware, and net-aware fill technologies have emerged to provide the designer with automated fill engines that support these new fill requirements, design changes that arrive late in the tapeout process (as engineering change orders, or ECOs) can have a disproportionate effect on tapeout schedules, due to the complexity of replacing fill. If not handled effectively, the impacts on file size, run time, and timing closure can significantly extend the tapeout process. In this paper, the authors examine changes to design flow methodology, supported by new fill technology, that enable efficient, fast, and accurate adjustments to metal fill late in the design process. We present an ECO fill methodology coupled with the support of advanced fill tools that can quickly locate the portion of the design affected by the change, remove and replace only the fill in that area, while maintaining the fill hierarchy. This new fill approach effectively reduces run time, contains fill file size, minimizes timing impact, and minimizes mask costs due to ECO-driven fill changes, all of which are critical factors to ensuring time-to-market schedules are maintained.

Engineered cartilaginous tubes for tracheal tissue replacement via self-assembly and fusion of human mesenchymal stem cell constructs.

PubMed

Dikina, Anna D; Strobel, Hannah A; Lai, Bradley P; Rolle, Marsha W; Alsberg, Eben

2015-06-01

There is a critical need to engineer a neotrachea because currently there are no long-term treatments for tracheal stenoses affecting large portions of the airway. In this work, a modular tracheal tissue replacement strategy was developed. High-cell density, scaffold-free human mesenchymal stem cell-derived cartilaginous rings and tubes were successfully generated through employment of custom designed culture wells and a ring-to-tube assembly system. Furthermore, incorporation of transforming growth factor-β1-delivering gelatin microspheres into the engineered tissues enhanced chondrogenesis with regard to tissue size and matrix production and distribution in the ring- and tube-shaped constructs, as well as luminal rigidity of the tubes. Importantly, all engineered tissues had similar or improved biomechanical properties compared to rat tracheas, which suggests they could be transplanted into a small animal model for airway defects. The modular, bottom up approach used to grow stem cell-based cartilaginous tubes in this report is a promising platform to engineer complex organs (e.g., trachea), with control over tissue size and geometry, and has the potential to be used to generate autologous tissue implants for human clinical applications. Copyright © 2015 Elsevier Ltd. All rights reserved.

77 FR 70481 - Fasco, A Division of Regal Beloit Corporation, Including On-Site Leased Workers From Penmac...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-26

... distribution of electric motors, as well as engineering, customer service and information technology (IT... portion of the supply of engineering services (or like or directly competitive services) to a foreign..., Missouri, who were engaged in employment related to the supply of warehousing, distribution, engineering...

75 FR 11915 - Chrysler LLC; Trenton Engine Plant, Including On-Site Leased Workers From Caravan Knight...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-12

... workers are engaged in the production of automotive engines, a substantial portion of which are shipped to..., Michigan location of Chrysler, LLC, Trenton Engine Plant. The Department has determined that these workers... Facilities Management, LLC, working on-site at the Trenton, Michigan location of Chrysler, LLC, Trenton...

Shape memory alloy heat engines and energy harvesting systems

DOEpatents

Browne, Alan L; Johnson, Nancy L; Keefe, Andrew C; Alexander, Paul W; Sarosi, Peter Maxwell; Herrera, Guillermo A; Yates, James Ryan

2013-12-17

A heat engine includes a first rotatable pulley and a second rotatable pulled spaced from the first rotatable pulley. A shape memory alloy (SMA) element is disposed about respective portions of the pulleys at an SMA pulley ratio. The SMA element includes first spring coil and a first fiber core within the first spring coil. A timing cable is disposed about disposed about respective portions of the pulleys at a timing pulley ratio, which is different than the SMA pulley ratio. The SMA element converts a thermal energy gradient between the hot region and the cold region into mechanical energy.

Workstation-Based Simulation for Rapid Prototyping and Piloted Evaluation of Control System Designs

NASA Technical Reports Server (NTRS)

Mansur, M. Hossein; Colbourne, Jason D.; Chang, Yu-Kuang; Aiken, Edwin W. (Technical Monitor)

1998-01-01

The development and optimization of flight control systems for modem fixed- and rotary-. wing aircraft consume a significant portion of the overall time and cost of aircraft development. Substantial savings can be achieved if the time required to develop and flight test the control system, and the cost, is reduced. To bring about such reductions, software tools such as Matlab/Simulink are being used to readily implement block diagrams and rapidly evaluate the expected responses of the completed system. Moreover, tools such as CONDUIT (CONtrol Designer's Unified InTerface) have been developed that enable the controls engineers to optimize their control laws and ensure that all the relevant quantitative criteria are satisfied, all within a fully interactive, user friendly, unified software environment.

Effects of a portion design plate on food group guideline adherence among hospital staff.

PubMed

de Korne, Dirk F; Malhotra, Rahul; Lim, Wai Yee; Ong, Christine; Sharma, Ashu; Tan, Tai Kiat; Tan, Thiam Chye; Ng, Kee Chong; Østbye, Truls

2017-01-01

Food group guideline adherence is vital to prevent obesity and diabetes. Various studies have demonstrated that environmental variables influence food intake behaviour. In the present study we examined the effect of a portion design plate with food group portion guidelines demarcated by coloured lines (ETE Plate™). A two-group quasi-experimental design was used to measure proportions of carbohydrate, vegetable and protein portions and user experience in a hospital staff lounge setting in Singapore. Lunch was served on the portion design plate before 12.15 hours. For comparison, a normal plate (without markings) was used after 12.15 hours. Changes in proportions of food groups from 2 months before the introduction of the design plate were analysed in a stratified sample at baseline (859 subjects, all on normal plates) to 1, 3 and 6 months after (in all 1016 subjects on the design plate, 968 subjects on the control plate). A total of 151 participants were asked about their experiences and opinions. Between-group comparisons were performed using t tests. Among those served on the portion design plate at 6 months after its introduction, the proportion of vegetables was 4·71 % ( P  < 0·001) higher and that of carbohydrates 2·83 % ( P  < 0·001) lower relative to the baseline. No significant change was found for proteins (-1·85 %). Over 6 months, we observed different change patterns between the different food group proportions. While participants were positive about the portion design plate, they did not think it would influence their personal behaviour. A portion design plate might stimulate food group guideline adherence among hospital staff and beyond.

Teaching habitat and animal classification to fourth graders using an engineering-design model

NASA Astrophysics Data System (ADS)

Marulcu, Ismail

2014-05-01

Background: The motivation for this work is built upon the premise that there is a need for research-based materials for design-based science instruction. In this paper, a small portion of our work investigating the impact of a LEGOTM engineering unit on fourth grade students' preconceptions and understanding of animals is presented. Purpose: The driving questions for our work are: (1) What is the impact of an engineering-design-based curricular module on students' understanding of habitat and animal classification? (2) What are students' misconceptions regarding animal classification and habitat? Sample: The study was conducted in an inner-city K-8 school in the northeastern region of the United States. There were two fourth grade classrooms in the school. The first classroom included seven girls and nine boys, whereas the other classroom included eight girls and eight boys. All fourth grade students participated in the study. Design and methods: In answering the research questions mixed-method approaches are used. Data collection methods included pre- and post-tests, pre- and post-interviews, student journals, and classroom observations. Identical pre- and post-tests were administered to measure students' understanding of animals. They included four multiple-choice and six open-ended questions. Identical pre- and post-interviews were administered to explore students' in-depth understanding of animals. Results: Our results show that students significantly increased their performance after instruction on both the multiple-choice questions (t = -3.586, p = .001) and the open-ended questions (t = -5.04, p = .000). They performed better on the post interviews as well. Also, it is found that design-based instruction helped students comprehend core concepts of a life science subject, animals. Conclusions: Based on these results, the main argument of the study is that engineering design is a useful framework for teaching not only physical science-related subjects, but also life science subjects in elementary science classrooms.

Introducing Deep Underground Science to Middle Schoolers: Challenges and Rewards

NASA Astrophysics Data System (ADS)

McMahan Norris, Margaret

2010-03-01

Work is in progress to define the mission, vision, scope and preliminary design of the Sanford Center for Science Education (SCSE), the education arm of the Deep Underground Science and Engineering Laboratory (DUSEL), a proposed major research facility of the National Science Foundation. If final funding is approved, DUSEL will be built at the site of the former Homestake Gold Mine in Lead, South Dakota beginning in 2012. The SCSE is envisioned to serve as a model for the integration of a science education center into the fabric of a new national laboratory. Its broad mission is to share the excitement and promise of deep underground science and engineering at Homestake with learners of all ages worldwide. The science to be pursued at DUSEL, whether in physics, astronomy, geomicrobiology, or geoscience, is transformational and sparks the imagination of learners of all ages. While the SCSE is under design, an early education program has been initiated that is designed to build capacity for the envisioned center, to prototype individual programs, and to build partnerships and community support. This talk will give an overview of the middle school portion of that program and its context within the overall content development plan of the SCSE.

Design approach of an aquaculture cage system for deployment in the constructed channel flow environments of a power plant

PubMed Central

Lee, Jihoon; Fredriksson, David W.; DeCew, Judson; Drach, Andrew; Yim, Solomon C.

2018-01-01

This study provides an engineering approach for designing an aquaculture cage system for use in constructed channel flow environments. As sustainable aquaculture has grown globally, many novel techniques have been introduced such as those implemented in the global Atlantic salmon industry. The advent of several highly sophisticated analysis software systems enables the development of such novel engineering techniques. These software systems commonly include three-dimensional (3D) drafting, computational fluid dynamics, and finite element analysis. In this study, a combination of these analysis tools is applied to evaluate a conceptual aquaculture system for potential deployment in a power plant effluent channel. The channel is supposedly clean; however, it includes elevated water temperatures and strong currents. The first portion of the analysis includes the design of a fish cage system with specific net solidities using 3D drafting techniques. Computational fluid dynamics is then applied to evaluate the flow reduction through the system from the previously generated solid models. Implementing the same solid models, a finite element analysis is performed on the critical components to assess the material stresses produced by the drag force loads that are calculated from the fluid velocities. PMID:29897954

Study of aerodynamic surface control of space shuttle boost and reentry, volume 1

NASA Technical Reports Server (NTRS)

Chang, C. J.; Connor, C. L.; Gill, G. P.

1972-01-01

The optimization technique is described which was used in the study for applying modern optimal control technology to the design of shuttle booster engine reaction control systems and aerodynamic control systems. Complete formulations are presented for both the ascent and reentry portions of the study. These formulations include derivations of the 6D perturbation equations of motion and the process followed in the control and blending law selections. A total hybrid software concept applied to the study is described in detail. Conclusions and recommendations based on the results of the study are included.

High temperature turbine engine structure

DOEpatents

Boyd, Gary L.

1991-01-01

A high temperature turbine engine includes a rotor portion having axially stacked adjacent ceramic rotor parts. A ceramic/ceramic joint structure transmits torque between the rotor parts while maintaining coaxial alignment and axially spaced mutually parallel relation thereof despite thermal and centrifugal cycling.

Integrated computational materials engineering: Tools, simulations and new applications

DOE PAGES

Madison, Jonathan D.

2016-03-30

Here, Integrated Computational Materials Engineering (ICME) is a relatively new methodology full of tremendous potential to revolutionize how science, engineering and manufacturing work together. ICME was motivated by the desire to derive greater understanding throughout each portion of the development life cycle of materials, while simultaneously reducing the time between discovery to implementation [1,2].

Portable boring machine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sverdlin, A.

This patent describes a boring machine for boring in situ spaced axially aligned bearing housings on an internal combustion engine body after removal of a crankshaft from the engine body. The bearing housings include a pair of opposed end bearing housings and intermediate bearing housings between the end bearing housings. The portable boring machine comprises: an elongate rotary boring bar mounted concentrically within the bearing housings and having ends extending outwardly from the opposed end bearing housings; an end mounting member wholly supported by each of the end bearing housings and positioned between the boring bar and the associated endmore » bearing housing for supporting the boring bar thereat. Each end mounting member includes an inner concentric portion engaging the boring bar and mounted for rotation therewith, an outer concentric portion engaging the inner surface of the adjacent end bearing housing and permitting relative rotation of the inner concentric portion and the boring bar, and adjusting means.« less

Multi-tube thermal fuse for nozzle protection from a flame holding or flashback event

DOEpatents

Lacy, Benjamin Paul; Davis, Jr., Lewis Berkley; Johnson, Thomas Edward; York, William David

2012-07-03

A protection system for a pre-mixing apparatus for a turbine engine, includes: a main body having an inlet portion, an outlet portion and an exterior wall that collectively establish a fuel delivery plenum; and a plurality of fuel mixing tubes that extend through at least a portion of the fuel delivery plenum, each of the plurality of fuel mixing tubes including at least one fuel feed opening fluidly connected to the fuel delivery plenum; at least one thermal fuse disposed on an exterior surface of at least one tube, the at least one thermal fuse including a material that will melt upon ignition of fuel within the at least one tube and cause a diversion of fuel from the fuel feed opening to at least one bypass opening. A method and a turbine engine in accordance with the protection system are also provided.

Method and apparatus for monitoring a hydrocarbon-selective catalytic reduction device

DOEpatents

Schmieg, Steven J; Viola, Michael B; Cheng, Shi-Wai S; Mulawa, Patricia A; Hilden, David L; Sloane, Thompson M; Lee, Jong H

2014-05-06

A method for monitoring a hydrocarbon-selective catalytic reactor device of an exhaust aftertreatment system of an internal combustion engine operating lean of stoichiometry includes injecting a reductant into an exhaust gas feedstream upstream of the hydrocarbon-selective catalytic reactor device at a predetermined mass flowrate of the reductant, and determining a space velocity associated with a predetermined forward portion of the hydrocarbon-selective catalytic reactor device. When the space velocity exceeds a predetermined threshold space velocity, a temperature differential across the predetermined forward portion of the hydrocarbon-selective catalytic reactor device is determined, and a threshold temperature as a function of the space velocity and the mass flowrate of the reductant is determined. If the temperature differential across the predetermined forward portion of the hydrocarbon-selective catalytic reactor device is below the threshold temperature, operation of the engine is controlled to regenerate the hydrocarbon-selective catalytic reactor device.

Advanced Small Rocket Chambers. Option 3: 110 1Bf Ir-Re Rocket, Volume 1

NASA Technical Reports Server (NTRS)

Jassowski, Donald M.; Schoenman, Leonard

1995-01-01

This report describes the AJ10-221, a high performance Iridium-coated Rhenium (Ir-Re) 110 lbf (490N) welded rocket chamber with 286:1 area ratio nozzle. This engine was designed, built, and hot fired for over 6 hours on this program. It demonstrated an I(s) of 321.8 sec, which is 10 sec higher than conventional 110 lbf silicide coated Cb chambers now in use. The approach used in this portion of the program was to demonstrate the performance improvement that can be made by the elimination of fuel film cooling and the use of a high temperature (4000F) (2200C) iridium-coated rhenium (Ir-Re) rocket chamber. Detailed thermal, performance, mechanical, and dynamic design analyses of the full engine were conducted by Aerojet. Two Ir-Re chambers were built to the Aerojet design by Ultramet, using the chemical vapor deposition (CVD) process. Incorporation of a secondary mixing device or Boundary Layer Trip (BLT) within the combustion chamber (Aerojet Patents 4882904 and 4936091) results in improvement in flow uniformity, and a significant life and performance increase. The 110 lbf engine design was verified in bolt-up hardware tests at sea level and altitude. The effects of injector design on performance were studied. Two duplicate injectors were fabricated matching the preferred design and were demonstrated to be interchangeable in operation. One of these units was fabricated matching the preferred design and was demonstrated to be interchangeable in operation. One of these units was welded into a flight type thruster which was tested for an accumulated duration of 22,590 sec in 93 firings, one of which was a continuous burn of two hours. A design deficiency in the C-103 nozzle near the Re-Cb transition joint was discovered, studied and corrected design has been prepared. Workhardening studies have been conducted to investigate methods for increasing the low yield strength of the Re in the annealed conditions. An advanced 490N high performance engine has been demonstrated which, when proven to be capable of withstanding launch vibration, is ready for flight qualification.

Software Engineering Education Directory. Software Engineering Curriculum Project

DTIC Science & Technology

1991-05-01

1986 with a questionnaire mailed to schools selected from Peterson’s Graduate Programs in Engineering and Applied Sciences 1986. We contacted schools...the publi- cation more complete. To discuss any issues related to this report, please contact: Education Program Software Engineering Institute...considered to be required course reading. How to Use This Section This portion of the directory is organized by state (in the U.S.), province (in

48 CFR 17.106-1 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., preproduction engineering, initial rework, initial spoilage, pilot runs, allocable portions of the costs of... should obtain in-house engineering cost estimates identifying the detailed recurring and nonrecurring... cancellation. For example, consider that the total nonrecurring costs (see 15.408, Table 15-2, Formats for...

48 CFR 17.106-1 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., preproduction engineering, initial rework, initial spoilage, pilot runs, allocable portions of the costs of... should obtain in-house engineering cost estimates identifying the detailed recurring and nonrecurring... cancellation. For example, consider that the total nonrecurring costs (see 15.408, Table 15-2, Formats for...

48 CFR 17.106-1 - General.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., preproduction engineering, initial rework, initial spoilage, pilot runs, allocable portions of the costs of... should obtain in-house engineering cost estimates identifying the detailed recurring and nonrecurring... cancellation. For example, consider that the total nonrecurring costs (see 15.408, Table 15-2, Formats for...

Ceramic Technology For Advanced Heat Engines Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-12-01

Significant accomplishments in fabricating ceramic components for the Department of Energy (DOE), National Aeronautics and Space Administration (NASA), and Department of Defense (DoD) advanced heat engine programs have provided evidence that the operation of ceramic parts in high-temperature engine environments is feasible. However, these programs have also demonstrated that additional research is needed in materials and processing development, design methodology, and data base and life prediction before industry will have a sufficient technology base from which to produce reliable cost-effective ceramic engine components commercially. The objective of the project is to develop the industrial technology base required for reliable ceramicsmore » for application in advanced automotive heat engines. The project approach includes determining the mechanisms controlling reliability, improving processes for fabricating existing ceramics, developing new materials with increased reliability, and testing these materials in simulated engine environments to confirm reliability. Although this is a generic materials project, the focus is on the structural ceramics for advanced gas turbine and diesel engines, ceramic bearings and attachments, and ceramic coatings for thermal barrier and wear applications in these engines. This advanced materials technology is being developed in parallel and close coordination with the ongoing DOE and industry proof of concept engine development programs. To facilitate the rapid transfer of this technology to U.S. industry, the major portion of the work is being done in the ceramic industry, with technological support from government laboratories, other industrial laboratories, and universities. Abstracts prepared for appropriate papers.« less

MAN-004 Design Standards Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Timothy L.

2014-07-01

At Sandia National Laboratories in New Mexico (SNL/NM), the design, construction, operation, and maintenance of facilities is guided by industry standards, a graded approach, and the systematic analysis of life cycle benefits received for costs incurred. The design of the physical plant must ensure that the facilities are "fit for use," and provide conditions that effectively, efficiently, and safely support current and future mission needs. In addition, SNL/NM applies sustainable design principles, using an integrated whole-building design approach, from site planning to facility design, construction, and operation to ensure building resource efficiency and the health and productivity of occupants. Themore » safety and health of the workforce and the public, any possible effects on the environment, and compliance with building codes take precedence over project issues, such as performance, cost, and schedule. These design standards generally apply to all disciplines on all SNL/NM projects. Architectural and engineering design must be both functional and cost-effective. Facility design must be tailored to fit its intended function, while emphasizing low-maintenance, energy-efficient, and energy-conscious design. Design facilities that can be maintained easily, with readily accessible equipment areas, low maintenance, and quality systems. To promote an orderly and efficient appearance, architectural features of new facilities must complement and enhance the existing architecture at the site. As an Architectural and Engineering (A/E) professional, you must advise the Project Manager when this approach is prohibitively expensive. You are encouraged to use professional judgment and ingenuity to produce a coordinated interdisciplinary design that is cost-effective, easily contractible or buildable, high-performing, aesthetically pleasing, and compliant with applicable building codes. Close coordination and development of civil, landscape, structural, architectural, fire protection, mechanical, electrical, telecommunications, and security features is expected to ensure compatibility with planned functional equipment and to facilitate constructability. If portions of the design are subcontracted to specialists, delivery of the finished design documents must not be considered complete until the subcontracted portions are also submitted for review. You must, along with support consultants, perform functional analyses and programming in developing design solutions. These solutions must reflect coordination of the competing functional, budgetary, and physical requirements for the project. During design phases, meetings between you and the SNL/NM Project Team to discuss and resolve design issues are required. These meetings are a normal part of the design process. For specific design-review requirements, see the project-specific Design Criteria. In addition to the design requirements described in this manual, instructive information is provided to explain the sustainable building practice goals for design, construction, operation, and maintenance of SNL/NM facilities. Please notify SNL/NM personnel of design best practices not included in this manual, so they can be incorporated in future updates.« less

Acclimating international graduate students to professional engineering ethics.

PubMed

Newberry, Byron; Austin, Katherine; Lawson, William; Gorsuch, Greta; Darwin, Thomas

2011-03-01

This article describes the education portion of an ongoing grant-sponsored education and research project designed to help graduate students in all engineering disciplines learn about the basic ethical principles, rules, and obligations associated with engineering practice in the United States. While the curriculum developed for this project is used for both domestic and international students, the educational materials were designed to be sensitive to the specific needs of international graduate students. In recent years, engineering programs in the United States have sought to develop a larger role for professional ethics education in the curriculum. Accreditation requirements, as well as pressures from the private sector, have helped facilitate this shift in focus. Almost half of all engineering graduate students in the U.S. are international students. Further, research indicates that the majority of these students will remain in the U.S. to work post-graduation. It is therefore in the interest of the profession that these students, coming from diverse backgrounds, receive some formal exposure to the professional and ethical expectations and norms of the engineering profession in the United States to help ensure that they have the knowledge and skills--non-technical as well as technical--required in today's engineering profession. In becoming acculturated to professional norms in a host country, international students face challenges that domestic students do not encounter; such as cultural competency, language proficiency, and acculturation stress. Mitigating these challenges must be a consideration in the development of any effective education materials. The present article discusses the project rationale and describes the development of on-line instructional materials aimed at helping international engineering graduate students acclimate to professional engineering ethics standards in the United States. Finally, a brief data summary of students' perceptions of the usefulness of the content and instructional interface is provided to demonstrate the initial effectiveness of the materials and to present a case for project sustainability.

43. Portion of Construction Drawing 2042F17, entitled 100 ft. Roundhouse, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. Portion of Construction Drawing 2042-F-17, entitled 100 ft. Roundhouse, Plan and Section of Typical Bay. Shown is a section showing soil bearing foundation and plan. (Original drawing, in the possession of Wyre Dick and Company, Livingston, New Jersey.) - Central Railroad of New Jersey, Engine Terminal, Jersey City, Hudson County, NJ

Toward a Fast-Response Active Turbine Tip Clearance Control

NASA Technical Reports Server (NTRS)

Melcher, Kevin J.; Kypuros, Javier A.

2003-01-01

This paper describes active tip clearance control research being conducted by NASA to improve turbine engine systems. The target application for this effort is commercial aircraft engines. However, technologies developed for clearance control can benefit a broad spectrum of current and future turbomachinery. The first portion of the paper addresses the research from a programmatic viewpoint. Recent studies that provide motivation for the work, identification of key technologies, and NASA's plan for addressing deficiencies in the technologies are discussed. The later portion of the paper drills down into one of the key technologies by presenting equations and results for a preliminary dynamic model of the tip clearance phenomena.

SPRITE: A TPS Test Bed for Ground and Flight

NASA Technical Reports Server (NTRS)

Prabhu, Dinesh K.; Agrawal, Parul; Peterson, Keith; Swanson, Gregory; Skokova, Kristina; Mangini, Nancy; Empey, Daniel M.; Gorbunov, Sergey; Venkatapathy, Ethiraj

2012-01-01

Engineers in the Entry Systems and Technology Division at NASA Ames Research Center developed a fully instrumented, small atmospheric entry probe called SPRITE (Small Probe Reentry Investigation for TPS Engineering). SPRITE, conceived as a flight test bed for thermal protection materials, was tested at full scale in an arc-jet facility so that the aerothermal environments the probe experiences over portions of its flight trajectory and in the arc-jet are similar. This ground-to-flight traceability enhances the ability of mission designers to evaluate margins needed in the design of thermal protection systems (TPS) of larger scale atmospheric entry vehicles. SPRITE is a 14-inch diameter, 45 deg. sphere-cone with a conical aftbody and designed for testing in the NASA Ames Aerodynamic Heating Facility (AHF). The probe is a two-part aluminum shell with PICA (phenolic impregnated carbon ablator) bonded on the forebody and LI-2200 (Shuttle tile material) bonded to the aftbody. Plugs with embedded thermocouples, similar to those installed in the heat shield of the Mars Science Laboratory (MSL), and a number of distributed sensors are integrated into the design. The data from these sensors are fed to an innovative, custom-designed data acquisition system also integrated with the test article. Two identical SPRITE models were built and successfully tested in late 2010-early 2011, and the concept is currently being modified to enable testing of conformable and/or flexible materials.

Process for forming a long gas turbine engine blade having a main wall with a thin portion near a tip

DOEpatents

Campbell, Christian X; Thomaidis, Dimitrios

2014-05-13

A process is provided for forming an airfoil for a gas turbine engine involving: forming a casting of a gas turbine engine airfoil having a main wall and an interior cavity, the main wall having a wall thickness extending from an external surface of the outer wall to the interior cavity, an outer section of the main wall extending from a location between a base and a tip of the airfoil casting to the tip having a wall thickness greater than a final thickness. The process may further involve effecting movement, using a computer system, of a material removal apparatus and the casting relative to one another such that a layer of material is removed from the casting at one or more radial portions along the main wall of the casting.

Stirling engine power control

DOEpatents

Fraser, James P.

1983-01-01

A power control method and apparatus for a Stirling engine including a valved duct connected to the junction of the regenerator and the cooler and running to a bypass chamber connected between the heater and the cylinder. An oscillating zone of demarcation between the hot and cold portions of the working gas is established in the bypass chamber, and the engine pistons and cylinders can run cold.

Advanced small rocket chambers. Option 3: 110 1bf Ir-Re rocket, volume 2

NASA Technical Reports Server (NTRS)

Jassowski, Donald M.; Schoenman, Leonard

1995-01-01

This is the second part of a two-part report that describes the AJ10-221, a high performance iridium-coated rhenium (Ir-Re) 110 lbf (490N) welded rocket chamber with 286:1 area ratio nozzle. This engine was designed, built, and hot fired for over 6 hours on this program. It demonstrated an I(s) of 321.8 sec, which is 10 sec higher than conventional 110 lbf silicide coated Cb chambers now in use. The approach used in this portion of the program was to demonstrate the performance improvement that can be made by the elimination of fuel film cooling and the use of a high temperature (4000 F) (2200 C) iridium-coated rhenium (Ir-Re) rocket chamber. Detailed thermal, performance, mechanical, and dynamic design analyses of the full engine were conducted by Aerojet. Two Ir-Re chambers were built to the Aerojet design by Ultramet, using the chemical vapor deposition (CVD) process. Incorporation of a secondary mixing device or Boundary Layer Trip (BLT) within the combustion chamber (Aerojet Patents 4882904 and 4936091) results in improvement in flow uniformity, and a significant life and performance increase. The 110 lbf engine design was verified in bolt-up hardware tests at sea level and altitude. The effects of injector design on performance were studied. Two duplicate injectors were fabricated matching the preferred design and were demonstrated to be interchangeable in operation. One of these units were welded into a flight type thruster which was tested for an accumulated duration of 22,590 sec in 93 firings, one of which was a continuous burn of two hours. A design deficiency in the C-103 nozzle near the Re-Cb transition joint was discovered, studied and corrected design has been prepared. Workhardening studies have been conducted to investigate methods for increasing the low yield strength of the Re in the annealed conditions. An advanced 490N high performance engine has been demonstrated which, when proven to be capable of withstanding launch vibration, is ready for flight qualification.

Ecological engineering alternatives for remediation and restoration of a drastically disturbed landscape

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nairn, R.W.; Hare, L.; Mercer, M.

As part of a Fall 1998 Environmental Science graduate seminar in Ecological Engineering at the University of Oklahoma, students were asked to submit a proposal for the holistic and sustainable restoration of the Tar Creek Superfund Site, Ottawa county, Oklahoma. the Tar Creek site is a portion of an abandoned lead and zinc mining area known as the Tri-State Mining District (OL, KS and MO) and includes approximately 104 square kilometers of disturbed land surface and contaminated water resources in extreme northeastern Oklahoma. Approximately 94 million cubic meters of contaminated water currently exist in the underground voids. In 1979, acidic,more » metal-rich waters began to discharge into Tar Creek from natural springs, bore holes and mine shafts. In addition, approximately 37 million cubic meters of processed mine waste materials (chat) litter their surface in large piles. Approximately 324 hectares of contaminated tailings settling ponds also exist on site. Student submitted proposals addressed the following four subject areas: passive treatment options for stream water quality improvement, surface reclamation and revegetation, stream habitat restoration and joint ecological and economic sustainability. Proposed designs for passive treatment of the contaminated mine drainage included unique constructed wetland designs that relief on a combination of biological and geochemical processes, use of microbial mats for luxury metal uptake, enhanced iron oxidation via windmill-based aeration and fly ash injection. proposed surface reclamation methods included minimal regrading following by biosolid, ash and other organic amendment applications and several phytoremediation techniques, especially the use of hyperaccumulators. The stream and riparian restoration portion of the proposals focused on chat removal, phytoremediation and species reintroduction. proposed joint ecological and economic sustainability ventures included development of recreational facilities, mining-based tourism and an Ecotechnology Research Park.« less

Tony Magri | NREL

Science.gov Websites

Windows System Engineer with the Computational Science Center. He implements, supports, and integrates Windows-based technology solutions at the ESIF and manages a portion of the VMware infrastructure . Throughout his career, Tony has built a strong skillset in enterprise Windows Engineering and Active

General Aviation Turbine Engine (GATE) study

NASA Technical Reports Server (NTRS)

Baerst, C. F.; Furst, D. G.

1979-01-01

The feasibility of turbine engines for the smaller general aviation aircraft was investigated and a technology program for developing the necessary technology was identified. Major results included the definition of the 1988 general aviation market, the identification of turboprop and turboshaft engines that meet the requirements of the aircraft studies, a benefit analysis showing the superiority of gas turbine engines for portions of the market studied, and detailed plans for the development of the necessary technology.

Lockheed Martin Skunk Works Single Stage to Orbit/Reusable Launch Vehicle

NASA Technical Reports Server (NTRS)

1999-01-01

Lockheed Martin Skunk Works has compiled an Annual Performance Report of the X-33/RLV Program. This report consists of individual reports from all industry team members, as well as NASA team centers. This portion of the report is comprised of a status report of Lockheed Martin's contribution to the program. The following is a summary of the Lockheed Martin Centers involved and work reviewed under their portion of the agreement: (1) Lockheed Martin Skunk Works - Vehicle Development, Operations Development, X-33 and RLV Systems Engineering, Manufacturing, Ground Operations, Reliability, Maintainability/Testability, Supportability, & Special Analysis Team, and X-33 Flight Assurance; (2) Lockheed Martin Technical Operations - Launch Support Systems, Ground Support Equipment, Flight Test Operations, and RLV Operations Development Support; (3) Lockheed Martin Space Operations - TAEM and A/L Guidance and Flight Control Design, Evaluation of Vehicle Configuration, TAEM and A/L Dispersion Analysis, Modeling and Simulations, Frequency Domain Analysis, Verification and Validation Activities, and Ancillary Support; (4) Lockheed Martin Astronautics-Denver - Systems Engineering, X-33 Development; (5) Sanders - A Lockheed Martin Company - Vehicle Health Management Subsystem Progress, GSS Progress; and (6) Lockheed Martin Michoud Space Systems - X-33 Liquid Oxygen (LOX) Tank, Key Challenges, Lessons Learned, X-33/RLV Composite Technology, Reusable Cyrogenic Insulation (RCI) and Vehicle Health Monitoring, Main Propulsion Systems (MPS), Structural Testing, X-33 System Integration and Analysis, and Cyrogenic Systems Operations.

KSC-2011-7397

NASA Image and Video Library

2011-10-14

CAPE CANAVERAL, Fla. – Louisiana State University mechanical engineering students Kevin Schenker, from left, and Jacob Koch join Luz Marina Calle, a scientist at NASA's Kennedy Space in Florida, as they examine a portion of the wall of the flame trench at Launch Pad 39B. Designers are looking for new, flame and vibration-resistant materials to line the trench. To help in the search, a team of mechanical engineering students at Louisiana State University are to build a scaled-down version of the flame trench that Kennedy's scientists can use to try out sample materials for the trench. If the samples work in the lab, they can be tried out in the real flame trenches at Launch Pad 39A and 39B. The launch pad has been refurbished extensively and work is continuing to modify the pad to support a variety of launch vehicles in the future. Photo credit: NASA/Jim Grossmann

The James Webb Space Telescope RealWorld-InWorld Design Challenge: Involving Professionals in a Virtual Classroom

NASA Astrophysics Data System (ADS)

Masetti, Margaret; Bowers, S.

2011-01-01

Students around the country are becoming experts on the James Webb Space Telescope by designing solutions to two of the design challenges presented by this complex mission. RealWorld-InWorld has two parts; the first (the Real World portion) has high-school students working face to face in their classroom as engineers and scientists. The InWorld phase starts December 15, 2010 as interested teachers and their teams of high school students register to move their work into a 3D multi-user virtual world environment. At the start of this phase, college students from all over the country choose a registered team to lead InWorld. Each InWorld team is also assigned an engineer or scientist mentor. In this virtual world setting, each team refines their design solutions and creates a 3D model of the Webb telescope. InWorld teams will use 21st century tools to collaborate and build in the virtual world environment. Each team will learn, not only from their own team members, but will have the opportunity to interact with James Webb Space Telescope researchers through the virtual world setting, which allows for synchronous interactions. Halfway through the challenge, design solutions will be critiqued and a mystery problem will be introduced for each team. The top five teams will be invited to present their work during a synchronous Education Forum April 14, 2011. The top team will earn scholarships and technology. This is an excellent opportunity for professionals in both astronomy and associated engineering disciplines to become involved with a unique educational program. Besides the chance to mentor a group of interested students, there are many opportunities to interact with the students as a guest, via chats and presentations.

Overview of X-38 Hypersonic Wind Tunnel Data and Comparison with Numerical Results

NASA Technical Reports Server (NTRS)

Campbell, Charles H.; Caram, Jose; Berry, Scott; DiFulvio, Michael; Horvath, Tom

1997-01-01

A NASA team of engineers has been organized to design a crew return vehicle for returning International Space Station crew members from orbit. The hypersonic characteristics of this X-23/X-2&4 derived crew return vehicle (designated X-38) are being evaluated in various wind tunnels in support of this effort. Aerodynamic data has been acquired in three NASA hypersonic facilities at Mach 20, and Mach 6. Computational Fluid Dynamics tools have been applied at the appropriate wind tunnel conditions to make comparisons with portions of this data. Experimental data from the Mach 6 Air and CF4 facilities illustrate a net positive pitching moment increment due to density ratio, as well as increased elevon effectiveness. Chemical nonequilibrium computational fluid dynamics solutions at flight conditions reinforce this conclusion.

KSC-2014-2639

NASA Image and Video Library

2014-05-21

CAPE CANAVERAL, Fla. – Team members from the University of Florida in Gainesville prepare their robot for the mining portion of NASA's 2014 Robotics Mining Competition at the Kennedy Space Center Visitor Complex in Florida. More than 35 teams from around the U.S. have designed and built remote-controlled robots for the mining competition. The competition is a NASA Human Exploration and Operations Mission Directorate project designed to engage and retain students in science, technology, engineering and mathematics, or STEM, fields by expanding opportunities for student research and design. Teams use their remote-controlled robotics to maneuver and dig in a supersized sandbox filled with a crushed material that has characteristics similar to Martian soil. The objective of the challenge is to see which team’s robot can collect and move the most regolith within a specified amount of time. For more information, visit www.nasa.gov/nasarmc. Photo credit: NASA/Frankie Martin

KSC-2014-2638

NASA Image and Video Library

2014-05-21

CAPE CANAVERAL, Fla. – The Hawai'l Marsbot Team members from Kapi'olani Community College in Hawaii prepare their robot for the mining portion of NASA's 2014 Robotics Mining Competition at the Kennedy Space Center Visitor Complex in Florida. More than 35 teams from around the U.S. have designed and built remote-controlled robots for the mining competition. The competition is a NASA Human Exploration and Operations Mission Directorate project designed to engage and retain students in science, technology, engineering and mathematics, or STEM, fields by expanding opportunities for student research and design. Teams use their remote-controlled robotics to maneuver and dig in a supersized sandbox filled with a crushed material that has characteristics similar to Martian soil. The objective of the challenge is to see which team’s robot can collect and move the most regolith within a specified amount of time. For more information, visit www.nasa.gov/nasarmc. Photo credit: NASA/Frankie Martin

KSC-2014-2653

NASA Image and Video Library

2014-05-22

CAPE CANAVERAL, Fla. – College and university teams prepare their robots for the mining portion of NASA’s 2014 Robotic Mining Competition at the Kennedy Space Center Visitor Complex in Florida. More than 35 teams from around the U.S. have designed and built remote-controlled robots for the mining competition. The competition is a NASA Human Exploration and Operations Mission Directorate project designed to engage and retain students in science, technology, engineering and mathematics, or STEM, fields by expanding opportunities for student research and design. Teams use their remote-controlled robotics to maneuver and dig in a supersized sandbox filled with a crushed material that has characteristics similar to Martian soil. The objective of the challenge is to see which team’s robot can collect and move the most regolith within a specified amount of time. For more information, visit www.nasa.gov/nasarmc. Photo credit: NASA/Kim Shiflett

KSC-2014-2640

NASA Image and Video Library

2014-05-21

CAPE CANAVERAL, Fla. – Team members from the University of Alabama prepare their robot for the mining portion of NASA's 2014 Robotics Mining Competition at the Kennedy Space Center Visitor Complex in Florida. More than 35 teams from around the U.S. have designed and built remote-controlled robots for the mining competition. The competition is a NASA Human Exploration and Operations Mission Directorate project designed to engage and retain students in science, technology, engineering and mathematics, or STEM, fields by expanding opportunities for student research and design. Teams use their remote-controlled robotics to maneuver and dig in a supersized sandbox filled with a crushed material that has characteristics similar to Martian soil. The objective of the challenge is to see which team’s robot can collect and move the most regolith within a specified amount of time. For more information, visit www.nasa.gov/nasarmc. Photo credit: NASA/Frankie Martin

KSC-2014-2637

NASA Image and Video Library

2014-05-21

CAPE CANAVERAL, Fla. – Team members from the University of North Dakota prepare their robot for the mining portion of NASA's 2014 Robotics Mining Competition at the Kennedy Space Center Visitor Complex in Florida. More than 35 teams from around the U.S. have designed and built remote-controlled robots for the mining competition. The competition is a NASA Human Exploration and Operations Mission Directorate project designed to engage and retain students in science, technology, engineering and mathematics, or STEM, fields by expanding opportunities for student research and design. Teams use their remote-controlled robotics to maneuver and dig in a supersized sandbox filled with a crushed material that has characteristics similar to Martian soil. The objective of the challenge is to see which team’s robot can collect and move the most regolith within a specified amount of time. For more information, visit www.nasa.gov/nasarmc. Photo credit: NASA/Frankie Martin

Retrofit photovoltaic systems for intermediate sized applications - A design and market study

NASA Astrophysics Data System (ADS)

Noel, G. T.; Hagely, J. R.

An assessment of the technical and economic feasibility of retrofitting a significant portion of the existing intermediate sector building/application inventory with photovoltaic systems is presented. The assessment includes the development of detailed engineering and architectural designs as well as cost estimates for 12 representative installations. Promising applications include retail stores, warehouses, office buildings, religious buildings, shopping centers, education buildings, hospitals, and industrial sites. A market study indicates that there is a national invetory of 1.5 to 2.0 million feasible intermediate sector applications, with the majority being in the 20 to 400 kW size range. The present cost of the major systems components and the cost of necessary building modifications are the primary current barriers to the realization of a large retrofit photovoltaic system market. The development of standardized modular system designs and installation techniques are feasible ways to minimize costs.

Thermodynamic Cycle Analysis of Magnetohydrodynamic-Bypass Airbreathing Hypersonic Engines

NASA Technical Reports Server (NTRS)

Litchford, Ron J.; Bityurin, Valentine A.; Lineberry, John T.

1999-01-01

Established analyses of conventional ramjet/scramjet performance characteristics indicate that a considerable decrease in efficiency can be expected at off-design flight conditions. This can be explained, in large part, by the deterioration of intake mass flow and limited inlet compression at low flight speeds and by the onset of thrust degradation effects associated with increased burner entry temperature at high flight speeds. In combination, these effects tend to impose lower and upper Mach number limits for practical flight. It has been noted, however, that Magnetohydrodynamic (MHD) energy management techniques represent a possible means for extending the flight Mach number envelope of conventional engines. By transferring enthalpy between different stages of the engine cycle, it appears that the onset of thrust degradation may be delayed to higher flight speeds. Obviously, the introduction of additional process inefficiencies is inevitable with this approach, but it is believed that these losses are more than compensated through optimization of the combustion process. The fundamental idea is to use MHD energy conversion processes to extract and bypass a portion of the intake kinetic energy around the burner. We refer to this general class of propulsion system as an MHD-bypass engine. In this paper, we quantitatively assess the performance potential and scientific feasibility of MHD-bypass airbreathing hypersonic engines using ideal gasdynamics and fundamental thermodynamic principles.

Pediatric Tubular Pulmonary Heart Valve from Decellularized Engineered Tissue Tubes

PubMed Central

Reimer, Jay M.; Syedain, Zeeshan H.; Haynie, Bee H.T.; Tranquillo, Robert T.

2015-01-01

Pediatric patients account for a small portion of the heart valve replacements performed, but a pediatric pulmonary valve replacement with growth potential remains an unmet clinical need. Herein we report the first tubular heart valve made from two decellularized, engineered tissue tubes attached with absorbable sutures, which can meet this need, in principle. Engineered tissue tubes were fabricated by allowing ovine dermal fibroblasts to replace a sacrificial fibrin gel with an aligned, cell-produced collagenous matrix, which was subsequently decellularized. Previously, these engineered tubes became extensively recellularized following implantation into the sheep femoral artery. Thus, a tubular valve made from these tubes may be amenable to recellularization and, ideally, somatic growth. The suture line pattern generated three equi-spaced “leaflets” in the inner tube, which collapsed inward when exposed to back pressure, per tubular valve design. Valve testing was performed in a pulse duplicator system equipped with a secondary flow loop to allow for root distention. All tissue-engineered valves exhibited full leaflet opening and closing, minimal regurgitation (< 5%), and low systolic pressure gradients (< 2.5 mmHg) under pulmonary conditions. Valve performance was maintained under various trans-root pressure gradients and no tissue damage was evident after 2 million cycles of fatigue testing. PMID:26036175

What's Left After a Tornado.

ERIC Educational Resources Information Center

Lawrence Inst. of Tech., Southfield, MI.

Following recent tornadoes, terms of specially trained architectural and engineering faculty conducted onsite examinations and research of building damage. It was concluded that tornado damage to buildings is predictable. A trained architect or engineer can establish, before a tornado strikes, those portions of the building that will offer the…

Reverse Core Engine with Thrust Reverser

NASA Technical Reports Server (NTRS)

Chandler, Jesse M. (Inventor); Suciu, Gabriel L. (Inventor)

2017-01-01

An engine system has a gas generator, a bi-fi wall surrounding at least a portion of the gas generator, a casing surrounding a fan, and the casing having first and second thrust reverser doors which in a deployed position abut each other and the bi-fi wall.

Middle School Regional Science Bowl Competition | Argonne National

Science.gov Websites

biology, chemistry, earth science, physics, energy, and math. The winner of the academic portion of the Biology IMEInstitute for Molecular Engineering JCESRJoint Center for Energy Storage Research MCSGMidwest Science and Engineering RISCRisk and Infrastructure Science Center SBCStructural Biology Center Energy.gov

Ceramic applications in the advanced Stirling automotive engine

NASA Technical Reports Server (NTRS)

Tomazic, W. A.; Cairelli, J. E.

1977-01-01

The ideal cycle, its application to a practical machine, and the specific advantages of high efficiency, low emissions, multi-fuel capability, and low noise of the stirling engine are discussed. Certain portions of the Stirling engine must operate continuously at high temperature. Ceramics offer the potential of cost reduction and efficiency improvement for advanced engine applications. Potential applications for ceramics in Stirling engines, and some of the special problems pertinent to using ceramics in the Stirling engine are described. The research and technology program in ceramics which is planned to support the development of advanced Stirling engines is outlined.

Approximation, abstraction and decomposition in search and optimization

NASA Technical Reports Server (NTRS)

Ellman, Thomas

1992-01-01

In this paper, I discuss four different areas of my research. One portion of my research has focused on automatic synthesis of search control heuristics for constraint satisfaction problems (CSPs). I have developed techniques for automatically synthesizing two types of heuristics for CSPs: Filtering functions are used to remove portions of a search space from consideration. Another portion of my research is focused on automatic synthesis of hierarchic algorithms for solving constraint satisfaction problems (CSPs). I have developed a technique for constructing hierarchic problem solvers based on numeric interval algebra. Another portion of my research is focused on automatic decomposition of design optimization problems. We are using the design of racing yacht hulls as a testbed domain for this research. Decomposition is especially important in the design of complex physical shapes such as yacht hulls. Another portion of my research is focused on intelligent model selection in design optimization. The model selection problem results from the difficulty of using exact models to analyze the performance of candidate designs.

10. Historic American Buildings Survey, PHOTOCOPY OF PLAN PORTION OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Historic American Buildings Survey, PHOTOCOPY OF PLAN PORTION OF J.M. WHITAKER'S SURVEY OF THE LIPPITT MILL, SHEET NO. 15912 DATED MARCH 22, 1913. Blue line ozalid print in the collection of the Department of Civil and Mechanical Engineering, Museum of History and Technology, the Smithsonian Institution. - Lippitt Mill, 825 Main Street, West Warwick, Kent County, RI

11. Historic American Buildings Survey, PHOTOCOPY OF ISOMETRIC PORTION OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Historic American Buildings Survey, PHOTOCOPY OF ISOMETRIC PORTION OF J.M. WHITAKER'S SURVEY OF THE LIPPITT MILL, SHEET NO. 15912 DATED MARCH 22, 1913. Blue line ozalid print in the collection of the Department of Civil and Mechanical Engineering, Museum of History and Technology, the Smithsonian Institution. - Lippitt Mill, 825 Main Street, West Warwick, Kent County, RI

Lock-up control system for an automatic transmission

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higashi, H.; Yashiki, S.; Waki, K.

A lock-up control system is described for an automatic transmission including a torque converter coupled with the output portion on an engine, and a power transmitting gear arrangement coupled with the output portion of the torque converter and controlled to vary the transmitting gear ratio therein by gear ratio control means in accordance with a shifting up or down command supplied to the latter. A lock-up clutch is provided for locking up the output portion of the torque converter to the output portion of the engine. The lock-up control system comprises: lock-up operation control means for controlling the lock-up clutchmore » to be in its operative state and in its inoperative state selectively, and for causing the lock-up clutch to be in the inoperative state thereof when the gear ratio control means performs the control with the shifting up or down command, and lock-up command means for preventing the lock-up operation control means from causing the lock-up clutch to be in the inoperative state thereof until a predetermined reductive variation in the speed of the output portion of the torque converter arises after the shifting up command is supplied to the gear ratio control means under the condition in which the lock-up clutch is in operation to hold a lock-up state.« less

In Situ Wetland Restoration Demonstration

DTIC Science & Technology

2014-07-01

Program (ESTCP) has funded the Naval Facilities Engineering and Expeditionary Warfare Center (NAVFAC EXWC) and its DoD partners: U.S. Army Public Health ...Command Engineering Service Center [NAVFAC ESC]) and its DoD partners U.S. Army Public Health Command, Naval Facilities Engineering Command Atlantic...made that unacceptable risks to human health or the environment may be present in portions of the Canal Creek system. Innovative technologies

Serial cooling of a combustor for a gas turbine engine

DOEpatents

Abreu, Mario E.; Kielczyk, Janusz J.

2001-01-01

A combustor for a gas turbine engine uses compressed air to cool a combustor liner and uses at least a portion of the same compressed air for combustion air. A flow diverting mechanism regulates compressed air flow entering a combustion air plenum feeding combustion air to a plurality of fuel nozzles. The flow diverting mechanism adjusts combustion air according to engine loading.

Damage-Tolerant Fan Casings for Jet Engines

NASA Technical Reports Server (NTRS)

2006-01-01

All turbofan engines work on the same principle. A large fan at the front of the engine draws air in. A portion of the air enters the compressor, but a greater portion passes on the outside of the engine this is called bypass air. The air that enters the compressor then passes through several stages of rotating fan blades that compress the air more, and then it passes into the combustor. In the combustor, fuel is injected into the airstream, and the fuel-air mixture is ignited. The hot gasses produced expand rapidly to the rear, and the engine reacts by moving forward. If there is a flaw in the system, such as an unexpected obstruction, the fan blade can break, spin off, and harm other engine components. Fan casings, therefore, need to be strong enough to contain errant blades and damage-tolerant to withstand the punishment of a loose blade-turned-projectile. NASA has spearheaded research into improving jet engine fan casings, ultimately discovering a cost-effective approach to manufacturing damage-tolerant fan cases that also boast significant weight reduction. In an aircraft, weight reduction translates directly into fuel burn savings, increased payload, and greater aircraft range. This technology increases safety and structural integrity; is an attractive, viable option for engine manufacturers, because of the low-cost manufacturing; and it is a practical alternative for customers, as it has the added cost saving benefits of the weight reduction.

The effect of Problem/Project-Based Learning on a desired skill set for construction professionals

NASA Astrophysics Data System (ADS)

Sirotiak, Todd L.

The purpose of this study was to investigate if a Problem/Project-Based Learning (PBL) approach can affect certain non-technical, "soft" skills of construction engineers. Such skills include leadership, adaptability, and stress management. In mixed design research, quantitative and qualitative data are assembled and analyzed collectively. For this study, two separate assessment tools were used for the quantitative portion, while open-ended written reflections and a partially closed-ended senior questionnaire were implemented for the qualitative portion. A hypothetical model was used to investigate certain soft skills based on prior research documenting need. Skills investigated were confidence, stress coping, leadership, communication skills, adaptability, and management skills. Descriptive statistics, open-ended final written reflections, and a partially closed-ended senior questionnaire were used to analyze the data. PBL is a process in which the students are challenged to develop realistic solutions on open, less structured, real world type problems. The results of this study performed with the combined count of nearly 60 students suggest that PBL can influence several soft skills of senior construction engineers. Specifically, these findings demonstrate the following: (a) PBL appears to affect students' soft skills; (b) students appear to recognize the realism and "real world" applicability that PBL brings to their skill development; and (c) the data suggest that the experience is holistic and offers opportunities for balanced growth in several ways. Some key competencies such as communication and leadership indicated significant enhancements. Although this study was limited to one academic year of the university's construction engineering program, it provides interesting insight to changes within the time period investigated. This study should be replicated in other construction engineering environments to investigate a larger population sample. In addition, industry, professional consultants, and academic entities are encouraged to review current learning methods to ensure that they are implementing the findings and methodology offered in this study.

INTEGRATION OF AIRBORNE DATA RECORDERS AND GROUND-BASED COMPUTERS FOR ENGINE MAINTENANCE PURPOSES.

DTIC Science & Technology

what is known as ASTROLOG . The other parts of the ASTROLOG include FAA crash recording capability on an extra channel of the existing voice recorder...and a continuously recording, magnetic tape, flight performance recorder. Highlights of the engine maintenance recorder portion of the ASTROLOG are discussed.

EFFECTS OF ENGINE SPEED AND ACCESSORY LOAD ON IDLING EMISSIONS FROM HEAVY-DUTY DIESEL TRUCK ENGINES

EPA Science Inventory

A nontrivial portion of heavy-duty vehicle emissions of nitrogen oxides (NOx) and particulate matter (PM) occurs during idling. Regulators and the environmental community are interested in curtailing truck idling emissions, but current emissions models do not characterize them ac...

EM-1 Countdown Simulation with Charlie Blackwell-Thompson

NASA Image and Video Library

2018-03-29

NASA Launch Director Charlie Blackwell-Thompson, center, stands next to her console in Firing Room 1 at the Kennedy Space Center's Launch Control Center. With her, from the left, are NASA intern Justin Connolly, NASA Engineering Project Manager Dan Tran, Blackwell-Thompson, Shawn Reverter, Project Manager for Red Canyon Software, Inc., and NASA Structures and Mechanisms Design Branch Chief Adam Dokos, during a countdown simulation for Exploration Mission 1. It was the agency's first simulation of a portion of the countdown for the first launch of a Space Launch System rocket and Orion spacecraft that will eventually take astronauts beyond low-Earth orbit to destinations such as the Moon and Mars.

Gas-Generator Augmented Expander Cycle Rocket Engine

NASA Technical Reports Server (NTRS)

Greene, William D. (Inventor)

2011-01-01

An augmented expander cycle rocket engine includes first and second turbopumps for respectively pumping fuel and oxidizer. A gas-generator receives a first portion of fuel output from the first turbopump and a first portion of oxidizer output from the second turbopump to ignite and discharge heated gas. A heat exchanger close-coupled to the gas-generator receives in a first conduit the discharged heated gas, and transfers heat to an adjacent second conduit carrying fuel exiting the cooling passages of a primary combustion chamber. Heat is transferred to the fuel passing through the cooling passages. The heated fuel enters the second conduit of the heat exchanger to absorb more heat from the first conduit, and then flows to drive a turbine of one or both of the turbopumps. The arrangement prevents the turbopumps exposure to combusted gas that could freeze in the turbomachinery and cause catastrophic failure upon attempted engine restart.

Combustor assembly in a gas turbine engine

DOEpatents

Wiebe, David J; Fox, Timothy A

2013-02-19

A combustor assembly in a gas turbine engine. The combustor assembly includes a combustor device coupled to a main engine casing, a first fuel injection system, a transition duct, and an intermediate duct. The combustor device includes a flow sleeve for receiving pressurized air and a liner disposed radially inwardly from the flow sleeve. The first fuel injection system provides fuel that is ignited with the pressurized air creating first working gases. The intermediate duct is disposed between the liner and the transition duct and defines a path for the first working gases to flow from the liner to the transition duct. An intermediate duct inlet portion is associated with a liner outlet and allows movement between the intermediate duct and the liner. An intermediate duct outlet portion is associated with a transition duct inlet section and allows movement between the intermediate duct and the transition duct.

Computational Fluid Dynamic Modeling of Rocket Based Combined Cycle Engine Flowfields

NASA Technical Reports Server (NTRS)

Daines, Russell L.; Merkle, Charles L.

1994-01-01

Computational Fluid Dynamic techniques are used to study the flowfield of a fixed geometry Rocket Based Combined Cycle engine operating in rocket ejector mode. Heat addition resulting from the combustion of injected fuel causes the subsonic engine flow to choke and go supersonic in the slightly divergent combustor-mixer section. Reacting flow computations are undertaken to predict the characteristics of solutions where the heat addition is determined by the flowfield. Here, adaptive gridding is used to improve resolution in the shear layers. Results show that the sonic speed is reached in the unheated portions of the flow first, while the heated portions become supersonic later. Comparison with results from another code show reasonable agreement. The coupled solutions show that the character of the combustion-based thermal choking phenomenon can be controlled reasonably well such that there is opportunity to optimize the length and expansion ratio of the combustor-mixer.

Hydrogen Storage Engineering Center of Excellence Metal Hydride Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Motyka, T.

2014-05-31

The Hydrogen Storage Engineering Center of Excellence (HSECoE) was established in 2009 by the U.S. Department of Energy (DOE) to advance the development of materials-based hydrogen storage systems for hydrogen-fueled light-duty vehicles. The overall objective of the HSECoE is to develop complete, integrated system concepts that utilize reversible metal hydrides, adsorbents, and chemical hydrogen storage materials through the use of advanced engineering concepts and designs that can simultaneously meet or exceed all the DOE targets. This report describes the activities and accomplishments during Phase 1 of the reversible metal hydride portion of the HSECoE, which lasted 30 months from Februarymore » 2009 to August 2011. A complete list of all the HSECoE partners can be found later in this report but for the reversible metal hydride portion of the HSECoE work the major contributing organizations to this effort were the United Technology Research Center (UTRC), General Motors (GM), Pacific Northwest National Laboratory (PNNL), the National Renewable Energy Laboratory (NREL) and the Savannah River National Laboratory (SRNL). Specific individuals from these and other institutions that supported this effort and the writing of this report are included in the list of contributors and in the acknowledgement sections of this report. The efforts of the HSECoE are organized into three phases each approximately 2 years in duration. In Phase I, comprehensive system engineering analyses and assessments were made of the three classes of storage media that included development of system level transport and thermal models of alternative conceptual storage configurations to permit detailed comparisons against the DOE performance targets for light-duty vehicles. Phase 1 tasks also included identification and technical justifications for candidate storage media and configurations that should be capable of reaching or exceeding the DOE targets. Phase 2 involved bench-level testing and evaluation of system configurations, including material packaging and balance-of-plant components, and conceptual design validation. Phase 3 includes fabrication and testing of the selected prototype storage system(s) for model validation and performance evaluation against the DOE targets. A DOE decision was needed for the HSECoE to advance to each phase and work on some classes of storage materials were recommended not to continue.« less

Jet engine nozzle exit configurations, including projections oriented relative to pylons, and associated systems and methods

NASA Technical Reports Server (NTRS)

Mengle, Vinod G. (Inventor); Thomas, Russell H. (Inventor)

2012-01-01

Nozzle exit configurations and associated systems and methods are disclosed. An aircraft system in accordance with one embodiment includes a jet engine exhaust nozzle having an internal flow surface and an exit aperture, with the exit aperture having a perimeter that includes multiple projections extending in an aft direction. Aft portions of individual neighboring projections are spaced apart from each other by a gap, and a geometric feature of the multiple can change in a monotonic manner along at least a portion of the perimeter. Projections near a support pylon and/or associated heat shield can have particular configurations, including greater flow immersion than other projections.

A Virtual Mission Operations Center: Collaborative Environment

NASA Technical Reports Server (NTRS)

Medina, Barbara; Bussman, Marie; Obenschain, Arthur F. (Technical Monitor)

2002-01-01

The Virtual Mission Operations Center - Collaborative Environment (VMOC-CE) intent is to have a central access point for all the resources used in a collaborative mission operations environment to assist mission operators in communicating on-site and off-site in the investigation and resolution of anomalies. It is a framework that as a minimum incorporates online chat, realtime file sharing and remote application sharing components in one central location. The use of a collaborative environment in mission operations opens up the possibilities for a central framework for other project members to access and interact with mission operations staff remotely. The goal of the Virtual Mission Operations Center (VMOC) Project is to identify, develop, and infuse technology to enable mission control by on-call personnel in geographically dispersed locations. In order to achieve this goal, the following capabilities are needed: Autonomous mission control systems Automated systems to contact on-call personnel Synthesis and presentation of mission control status and history information Desktop tools for data and situation analysis Secure mechanism for remote collaboration commanding Collaborative environment for remote cooperative work The VMOC-CE is a collaborative environment that facilitates remote cooperative work. It is an application instance of the Virtual System Design Environment (VSDE), developed by NASA Goddard Space Flight Center's (GSFC) Systems Engineering Services & Advanced Concepts (SESAC) Branch. The VSDE is a web-based portal that includes a knowledge repository and collaborative environment to serve science and engineering teams in product development. It is a "one stop shop" for product design, providing users real-time access to product development data, engineering and management tools, and relevant design specifications and resources through the Internet. The initial focus of the VSDE has been to serve teams working in the early portion of the system/product lifecycle - concept development, proposal preparation, and formulation. The VMOC-CE expands the application of the VSDE into the operations portion of the system lifecycle. It will enable meaningful and real-time collaboration regardless of the geographical distribution of project team members. Team members will be able to interact in satellite operations, specifically for resolving anomalies, through access to a desktop computer and the Internet. Mission Operations Management will be able to participate and monitor up to the minute status of anomalies or other mission operations issues. In this paper we present the VMOC-CE project, system capabilities, and technologies.

Mid-section of a can-annular gas turbine engine with an improved rotation of air flow from the compressor to the turbine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Little, David A.; Schilp, Reinhard; Ross, Christopher W.

A midframe portion (313) of a gas turbine engine (310) is presented and includes a compressor section with a last stage blade to orient an air flow (311) at a first angle (372). The midframe portion (313) further includes a turbine section with a first stage blade to receive the air flow (311) oriented at a second angle (374). The midframe portion (313) further includes a manifold (314) to directly couple the air flow (311) from the compressor section to a combustor head (318) upstream of the turbine section. The combustor head (318) introduces an offset angle in the airmore » flow (311) from the first angle (372) to the second angle (374) to discharge the air flow (311) from the combustor head (318) at the second angle (374). While introducing the offset angle, the combustor head (318) at least maintains or augments the first angle (372).« less

Carburetor for internal combustion engines

DOEpatents

Csonka, John J.; Csonka, Albert B.

1978-01-01

A carburetor for internal combustion engines having a housing including a generally discoidal wall and a hub extending axially from the central portion thereof, an air valve having a relatively flat radially extending surface directed toward and concentric with said discoidal wall and with a central conoidal portion having its apex directed toward the interior of said hub portion. The housing wall and the radially extending surface of the valve define an air passage converging radially inwardly to form an annular valving construction and thence diverge into the interior of said hub. The hub includes an annular fuel passage terminating at its upper end in a circumferential series of micro-passages for directing liquid fuel uniformly distributed into said air passage substantially at said valving constriction at right angles to the direction of air flow. The air valve is adjustable axially toward and away from the discoidal wall of the carburetor housing to regulate the volume of air drawn into the engine with which said carburetor is associated. Fuel is delivered under pressure to the fuel metering valve and from there through said micro-passages and controlled cams simultaneously regulate the axial adjustment of said air valve and the rate of delivery of fuel through said micro-passages according to a predetermined ratio pattern. A third jointly controlled cam simultaneously regulates the ignition timing in accordance with various air and fuel supply settings. The air valve, fuel supply and ignition timing settings are all independent of the existing degree of engine vacuum.

Turbofan engine demonstration of sensor failure detection

NASA Technical Reports Server (NTRS)

Merrill, Walter C.; Delaat, John C.; Abdelwahab, Mahmood

1991-01-01

In the paper, the results of a full-scale engine demonstration of a sensor failure detection algorithm are presented. The algorithm detects, isolates, and accommodates sensor failures using analytical redundancy. The experimental hardware, including the F100 engine, is described. Demonstration results were obtained over a large portion of a typical flight envelope for the F100 engine. They include both subsonic and supersonic conditions at both medium and full, nonafter burning, power. Estimated accuracy, minimum detectable levels of sensor failures, and failure accommodation performance for an F100 turbofan engine control system are discussed.

Development of Maximum Considered Earthquake Ground Motion Maps

USGS Publications Warehouse

Leyendecker, E.V.; Hunt, R.J.; Frankel, A.D.; Rukstales, K.S.

2000-01-01

The 1997 NEHRP Recommended Provisions for Seismic Regulations for New Buildings use a design procedure that is based on spectral response acceleration rather than the traditional peak ground acceleration, peak ground velocity, or zone factors. The spectral response accelerations are obtained from maps prepared following the recommendations of the Building Seismic Safety Council's (BSSC) Seismic Design Procedures Group (SDPG). The SDPG-recommended maps, the Maximum Considered Earthquake (MCE) Ground Motion Maps, are based on the U.S. Geological Survey (USGS) probabilistic hazard maps with additional modifications incorporating deterministic ground motions in selected areas and the application of engineering judgement. The MCE ground motion maps included with the 1997 NEHRP Provisions also serve as the basis for the ground motion maps used in the seismic design portions of the 2000 International Building Code and the 2000 International Residential Code. Additionally the design maps prepared for the 1997 NEHRP Provisions, combined with selected USGS probabilistic maps, are used with the 1997 NEHRP Guidelines for the Seismic Rehabilitation of Buildings.

Materials-Enabled High-Efficiency (MEHE) Heavy-Duty Diesel Engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kass, M.; Veliz, M.

2011-09-30

The purpose of this Cooperative Research and Development Agreement (CRADA) between UTBattelle, Inc. and Caterpillar, Inc. was to improve diesel engine efficiency by incorporating advanced materials to enable higher combustion pressures and temperatures necessary for improved combustion. The project scope also included novel materials for use in advanced components and designs associated with waste-heat recovery and other concepts for improved thermal efficiency. Caterpillar initially provided ORNL with a 2004 Tier 2 C15 ACERT diesel engine (designed for on-highway use) and two 600 hp motoring dynamometers. The first year of the CRADA effort was focused on establishing a heavy-duty experimental enginemore » research cell. First year activities included procuring, installing and commissioning the cell infrastructure. Infrastructure components consisted of intake air handling system, water tower, exhaust handling system, and cell air conditioning. Other necessary infrastructure items included the fuel delivery system and bottled gas handling to support the analytical instrumentation. The second year of the CRADA focused on commissioning the dynamometer system to enable engine experimentation. In addition to the requirements associated with the dynamometer controller, the electrical system needed a power factor correction system to maintain continuity with the electrical grid. During the second year the engine was instrumented and baseline operated to confirm performance and commission the dynamometer. The engine performance was mapped and modeled according to requirements provided by Caterpillar. This activity was further supported by a Work-for-Others project from Caterpillar to evaluate a proprietary modeling system. A second Work-for-Others activity was performed to evaluate a novel turbocharger design. This project was highly successful and may lead to new turbocharger designs for Caterpillar heavy-duty diesel engines. During the third (and final) year of the CRADA, a novel valve material was evaluated to assess high temperature performance and durability. A series of prototype valves, composed of a unique nickel-alloy was placed in the engine head. The engine was aggressively operated using a transient test cycle for 200 hours. The valve recession was periodically measured to determine valve performance. Upon completion of the test the valves were removed and returned to Caterpillar for additional assessment. Industrial in-kind support was available throughout the project period. Review of the status and research results were carried out on a regular basis (meetings and telecons) which included direction for future work activities. A significant portion of the industrial support was in the form of information exchange and technical consultation.« less

Extending operating range of a homogeneous charge compression ignition engine via cylinder deactivation

DOEpatents

Hergart, Carl-Anders [Peoria, IL; Hardy, William L [Peoria, IL; Duffy, Kevin P [Metamora, IL; Liechty, Michael P [Chillicothe, IL

2008-05-27

An HCCI engine has the ability to operate over a large load range by utilizing a lower cetane distillate diesel fuel to increase ignition delay. This permits more stable operation at high loads by avoidance of premature combustion before top dead center. During low load conditions, a portion of the engines cylinders are deactivated so that the remaining cylinders can operate at a pseudo higher load while the overall engine exhibits behavior typical of a relatively low load.

Closed-loop air cooling system for a turbine engine

DOEpatents

North, William Edward

2000-01-01

Method and apparatus are disclosed for providing a closed-loop air cooling system for a turbine engine. The method and apparatus provide for bleeding pressurized air from a gas turbine engine compressor for use in cooling the turbine components. The compressed air is cascaded through the various stages of the turbine. At each stage a portion of the compressed air is returned to the compressor where useful work is recovered.

Laser ignition

DOEpatents

Early, James W.; Lester, Charles S.

2002-01-01

In the apparatus of the invention, a first excitation laser or other excitation light source is used in tandem with an ignitor laser to provide a compact, durable, engine deployable fuel ignition laser system. The beam from the excitation light source is split with a portion of it going to the ignitor laser and a second portion of it being recombined with the first portion after a delay before injection into the ignitor laser. Reliable fuel ignition is provided over a wide range of fuel conditions by using a single remote excitation light source for one or more small lasers located proximate to one or more fuel combustion zones.

Using pattern based layout comparison for a quick analysis of design changes

NASA Astrophysics Data System (ADS)

Huang, Lucas; Yang, Legender; Kan, Huan; Zou, Elain; Wan, Qijian; Du, Chunshan; Hu, Xinyi; Liu, Zhengfang

2018-03-01

A design usually goes through several versions until achieving a most successful one. These changes between versions are not a complete substitution but a continual improvement, either fixing the known issues of its prior versions (engineering change order) or a more optimized design substitution of a portion of the design. On the manufacturing side, process engineers care more about the design pattern changes because any new pattern occurrence may be a killer of the yield. An effective and efficient way to narrow down the diagnosis scope appeals to the engineers. What is the best approach of comparing two layouts? A direct overlay of two layouts may not always work as even though most of the design instances will be kept in the layout from version to version, the actual placements may be different. An alternative way, pattern based layout comparison, comes to play. By expanding this application, it makes it possible to transfer the learning in one cycle to another and accelerate the process of failure analysis. This paper presents a solution to compare two layouts by using Calibre DRC and Pattern Matching. The key step in this flow is layout decomposition. In theory, with a fixed pattern size, a layout can always be decomposed into limited number of patterns by moving the pattern center around the layout, the number is limited but may be huge if the layout is not processed smartly! A mathematical answer is not what we are looking for but an engineering solution is more desired. Layouts must be decomposed into patterns with physical meaning in a smart way. When a layout is decomposed and patterns are classified, a pattern library with unique patterns inside is created for that layout. After individual pattern libraries for each layout are created, run pattern comparison utility provided by Calibre Pattern Matching to compare the pattern libraries, unique patterns will come out for each layout. This paper illustrates this flow in details and demonstrates the advantage of combining Calibre DRC and Calibre Pattern Matching.

Enhancing Non-Technical Skills by a Multidisciplinary Engineering Summer School

ERIC Educational Resources Information Center

Larsen, Peter Gorm; Kristiansen, Erik Lasse; Bennedsen, Jens; Bjerge, Kim

2017-01-01

In general engineering studies focus on the technical skills in their own discipline. However, in their subsequent industrial careers, a significant portion of their time needs to be devoted to non-technical skills. In addition, in an increasingly globalised world collaboration in teams across cultures and disciplines is paramount to the creation…

Investigation of the fuel feed line failures on the Space Shuttle main engine

NASA Technical Reports Server (NTRS)

Larson, E. W.

1980-01-01

The Space Shuttle Main Engine (SSME) development program experienced two similar appearing fuel feed line failures during the shutdown portion of two engine tests. Failure investigations into each incident showed that a few cycles of high-amplitude transient strain occurring during the start and cutoff portions of each test could have either accumulated damage and led to a fatigue failure after 46 tests, or caused rupture in a low-strength weld joint. The cause of the high strain was traced to a period of unsteady flow separation during the start and cutoff of each test coincident with the oblique shock approaching the nozzle exit. Since elimination of the flow separation was impractical, the steps taken to allow engine development and flight preparations to continue were: (1) establish the safe operating life of the nozzle, (2) reinforce all low-strength welds, and (3) eliminate the use of thin-wall fuel feed lines. In parallel, the feed line was redesigned and fabrication was initiated on units to be incorporated into the development program.

Energy Efficient Engine Program: Technology Benefit/Cost Study, Volume II

NASA Technical Reports Server (NTRS)

Gray, D. E.; Gardner, W. B.

1983-01-01

The Benefit/Cost Study portion of the NASA-sponsored Energy Efficient Engine Component Development and Integration program was successful in achieving its objectives: identification of air transport propulsion system technology requirements for the years 2000 and 2010, and formulation of programs for developing these technologies. It is projected that the advanced technologies identified, when developed to a state of readiness, will provide future commercial and military turbofan engines with significant savings in fuel consumption and related operating costs. These benefits are significant and far from exhausted. The potential savings translate into billions of dollars in annual savings for the airlines. Analyses indicate that a significant portion of the overall savings is attributed to aerodynamic and structure advancements. Another important consideration in acquiring these benefits is developing a viable reference technology base that will permit engines to operate at substantially higher overall pressure ratios and bypass ratios. Results have pointed the direction for future research and a comprehensive program plan for achieving this was formulated. The next major step is initiating the program effort that will convert the advanced technologies into the expected benefits.

Fuel-Air Mixing and Combustion in Scramjets. Chapter 6

NASA Technical Reports Server (NTRS)

Drummond, J. Philip; Diskin, Glenn S.; Cutler, Andrew D.

2006-01-01

At flight speeds, the residence time for atmospheric air ingested into a scramjet inlet and exiting from the engine nozzle is on the order of a millisecond. Therefore, fuel injected into the air must efficiently mix within tens of microseconds and react to release its energy in the combustor. The overall combustion process should be mixing controlled to provide a stable operating environment; in reality, however, combustion in the upstream portion of the combustor, particularly at higher Mach numbers, is kinetically controlled where ignition delay times are on the same order as the fluid scale. Both mixing and combustion time scales must be considered in a detailed study of mixing and reaction in a scramjet to understand the flow processes and to ultimately achieve a successful design. Although the geometric configuration of a scramjet is relatively simple compared to a turbomachinery design, the flow physics associated with the simultaneous injection of fuel from multiple injector configurations, and the mixing and combustion of that fuel downstream of the injectors is still quite complex. For this reason, many researchers have considered the more tractable problem of a spatially developing, primarily supersonic, chemically reacting mixing layer or jet that relaxes only the complexities introduced by engine geometry. All of the difficulties introduced by the fluid mechanics, combustion chemistry, and interactions between these phenomena can be retained in the reacting mixing layer, making it an ideal problem for the detailed study of supersonic reacting flow in a scramjet. With a good understanding of the physics of the scramjet internal flowfield, the designer can then return to the actual scramjet geometry with this knowledge and apply engineering design tools that more properly account for the complex physics. This approach will guide the discussion in the remainder of this section.

A Cabled, High Bandwidth Instrument Platform for Continuous Scanning of the Upper Ocean Water Column

NASA Astrophysics Data System (ADS)

McRae, E.; Delaney, J. R.; Kelly, D.; Daly, K. L.; Luther, D. S.; Harkins, G.; Harrington, M.; McGuire, C.; Tilley, J.; Dosher, J.; Waite, P.; Cram, G.; Kawka, O. E.

2016-02-01

The Cabled Array portion of the National Science Foundation funded Ocean Observatories Initiative is a large scale, high bandwidth and high power subsea science network designed by the University of Washington Applied Physics Laboratory. Part of that system is a set of winched profilers which continuously scan the upper 200m of the ocean at their deployment sites. The custom built profilers leverage the Cabled Array's technology for interfacing collections of science instruments and add the ability to run predefined missions and to switch missions or mission parameters on the fly via command from shore. The profilers were designed to operate continuously for up to two years after deployment after which certain wearing components must be replaced. The data from the profiler's science and engineering sensors are streamed to shore via the seafloor network in real time. Data channel capacity from the profilers exceeds 40 Mbps. For profiler safety, mission execution is controlled within the platform. Inputs such as 3D gyro, pressure depth and deployed cable calculations are monitored to assure safe operation during any sea state. The profilers never surface but are designed to approach within 5m of the surface if conditions allow. Substantial engineering effort was focused on reliable cable handling under all ocean conditions. The profilers are currently operated from subsea moorings which also contain sets of fixed science and engineering sensors. The profilers and their associated mooring instrument assemblies are designed for rapid replacement using ROVs. We have operated this system for two years, including one annual maintenance turn and information relative to that experience will be included in the paper.[Image Caption] Cabled Array Shallow Profiler shown in its parking position.

An Ejector Air Intake Design Method for a Novel Rocket-Based Combined-Cycle Rocket Nozzle

NASA Astrophysics Data System (ADS)

Waung, Timothy S.

Rocket-based combined-cycle (RBCC) vehicles have the potential to reduce launch costs through the use of several different air breathing engine cycles, which reduce fuel consumption. The rocket-ejector cycle, in which air is entrained into an ejector section by the rocket exhaust, is used at flight speeds below Mach 2. This thesis develops a design method for an air intake geometry around a novel RBCC rocket nozzle design for the rocket-ejector engine cycle. This design method consists of a geometry creation step in which a three-dimensional intake geometry is generated, and a simple flow analysis step which predicts the air intake mass flow rate. The air intake geometry is created using the rocket nozzle geometry and eight primary input parameters. The input parameters are selected to give the user significant control over the air intake shape. The flow analysis step uses an inviscid panel method and an integral boundary layer method to estimate the air mass flow rate through the intake geometry. Intake mass flow rate is used as a performance metric since it directly affects the amount of thrust a rocket-ejector can produce. The design method results for the air intake operating at several different points along the subsonic portion of the Ariane 4 flight profile are found to under predict mass flow rate by up to 8.6% when compared to three-dimensional computational fluid dynamics simulations for the same air intake.

Method of Manufacturing Carbon Fiber Reinforced Carbon Composite Valves

NASA Technical Reports Server (NTRS)

Rivers, H. Kevin (Inventor); Ransone, Philip O. (Inventor); Northam, G. Burton (Inventor)

1998-01-01

A method for forming a carbon composite valve for internal combustion engines is discussed. The process includes the steps of braiding carbon fiber into a rope thereby forming a cylindrically shaped valve stem portion and continuing to braid said fiber while introducing into the braiding carbon fiber rope a carbon matrix plug having an outer surface in a net shape of a valve head thereby forming a valve head portion. The said carbon matrix plug acting as a mandrel over which said carbon fiber rope is braided, said carbon fiber rope and carbon matrix plug forming a valve head portion suitable for mating with a valve seat; cutting said braided carbon valve stem portion at one end to form a valve tip and cutting said braided carbon fiber after said valve head portion to form a valve face and thus provide a composite valve preform; and densifying said preform by embedding the braided carbon in a matrix of carbon to convert said valve stem portion to a valve stem and said valve head portion to a valve head thereby providing said composite valve.

Chemical composition and photochemical reactivity of exhaust from aircraft turbine engines

NASA Astrophysics Data System (ADS)

Spicer, C. W.; Holdren, M. W.; Riggin, R. M.; Lyon, T. F.

1994-10-01

Assessment of the environmental impact of aircraft emissions is required by planners and policy makers. Seveal areas of concern are: 1. exposure of airport workers and urban residents to toxic chemicals emitted when the engines operate at low power (idle and taxi) on the ground; 2. contributions to urban photochemical air pollution of aircraft volatile organic and nitrogen oxides emissions from operations around airports; and 3. emissions of nitrogen oxides and particles during high-altitude operation. The environmental impact of chemicals emitted from jet aircraft turbine engines has not been firmly established due to lack of data regarding emission rates and identities of the compounds emitted. This paper describes an experimental study of two different aircraft turbine engines designed to determine detailed organic emissions, as well as emissions of inorganic gases. Emissions were measured at several engine power settings. Measurements were made of detailed organic composition from C1 through C17, CO, CO2, NO, NOx, and polycyclic aromatic hydrocarbons. Measurements were made using a multi-port sampling pro be positioned directly behind the engine in the exhaust exit plane. The emission measurements have been used to determine the organic distribution by carbon number and the distribution by compound class at each engine power level. The sum of the organic species was compared with an independent measurement of total organic carbon to assess the carbon mass balance. A portion of the exhaust was captured and irradiated in outdoor smog chambers to assess the photochemical reactivity of the emissions with respect to ozone formation. The reactivity of emissions from the two engines was apportioned by chemical compound class.

33 CFR 334.763 - Naval Support Activity Panama City; Gulf of Mexico; restricted area.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE DANGER ZONE AND RESTRICTED AREA REGULATIONS § 334..., 085°47′29″ W; West point—30°07′55″ N, 085°51′05″ W, then northerly to point of origin. (b) The restrictions. (1) For the purposes of this section, “military security zones” are specific portion/s within any...

Simple uncertainty propagation for early design phase aircraft sizing

NASA Astrophysics Data System (ADS)

Lenz, Annelise

Many designers and systems analysts are aware of the uncertainty inherent in their aircraft sizing studies; however, few incorporate methods to address and quantify this uncertainty. Many aircraft design studies use semi-empirical predictors based on a historical database and contain uncertainty -- a portion of which can be measured and quantified. In cases where historical information is not available, surrogate models built from higher-fidelity analyses often provide predictors for design studies where the computational cost of directly using the high-fidelity analyses is prohibitive. These surrogate models contain uncertainty, some of which is quantifiable. However, rather than quantifying this uncertainty, many designers merely include a safety factor or design margin in the constraints to account for the variability between the predicted and actual results. This can become problematic if a designer does not estimate the amount of variability correctly, which then can result in either an "over-designed" or "under-designed" aircraft. "Under-designed" and some "over-designed" aircraft will likely require design changes late in the process and will ultimately require more time and money to create; other "over-designed" aircraft concepts may not require design changes, but could end up being more costly than necessary. Including and propagating uncertainty early in the design phase so designers can quantify some of the errors in the predictors could help mitigate the extent of this additional cost. The method proposed here seeks to provide a systematic approach for characterizing a portion of the uncertainties that designers are aware of and propagating it throughout the design process in a procedure that is easy to understand and implement. Using Monte Carlo simulations that sample from quantified distributions will allow a systems analyst to use a carpet plot-like approach to make statements like: "The aircraft is 'P'% likely to weigh 'X' lbs or less, given the uncertainties quantified" without requiring the systems analyst to have substantial knowledge of probabilistic methods. A semi-empirical sizing study of a small single-engine aircraft serves as an example of an initial version of this simple uncertainty propagation. The same approach is also applied to a variable-fidelity concept study using a NASA-developed transonic Hybrid Wing Body aircraft.

Shape memory alloy heat engines and energy harvesting systems

DOEpatents

Browne, Alan L; Johnson, Nancy L; Shaw, John Andrew; Churchill, Christopher Burton; Keefe, Andrew C; McKnight, Geoffrey P; Alexander, Paul W; Herrera, Guillermo A; Yates, James Ryan; Brown, Jeffrey W

2014-09-30

A heat engine includes a first rotatable pulley and a second rotatable pulley spaced from the first rotatable pulley. A shape memory alloy (SMA) element is disposed about respective portions of the pulleys at an SMA pulley ratio. The SMA element includes a first wire, a second wire, and a matrix joining the first wire and the second wire. The first wire and the second wire are in contact with the pulleys, but the matrix is not in contact with the pulleys. A timing cable is disposed about respective portions of the pulleys at a timing pulley ratio, which is different than the SMA pulley ratio. The SMA element converts a thermal energy gradient between the hot region and the cold region into mechanical energy.

Gas turbine engine

DOEpatents

Lawlor, Shawn P.; Roberts, II, William Byron

2016-03-08

A gas turbine engine with a compressor rotor having compressor impulse blades that delivers gas at supersonic conditions to a stator. The stator includes a one or more aerodynamic ducts that each have a converging portion and a diverging portion for deceleration of the selected gas to subsonic conditions and to deliver a high pressure oxidant containing gas to flameholders. The flameholders may be provided as trapped vortex combustors, for combustion of a fuel to produce hot pressurized combustion gases. The hot pressurized combustion gases are choked before passing out of an aerodynamic duct to a turbine. Work is recovered in a turbine by expanding the combustion gases through impulse blades. By balancing the axial loading on compressor impulse blades and turbine impulse blades, asymmetrical thrust is minimized or avoided.

B-1 AFT Nacelle Flow Visualization Study

NASA Technical Reports Server (NTRS)

Celniker, Robert

1975-01-01

A 2-month program was conducted to perform engineering evaluation and design tasks to prepare for visualization and photography of the airflow along the aft portion of the B-1 nacelles and nozzles during flight test. Several methods of visualizing the flow were investigated and compared with respect to cost, impact of the device on the flow patterns, suitability for use in the flight environment, and operability throughout the flight. Data were based on a literature search and discussions with the test personnel. Tufts were selected as the flow visualization device in preference to several other devices studied. A tuft installation pattern has been prepared for the right-hand aft nacelle area of B-1 air vehicle No.2. Flight research programs to develop flow visualization devices other than tufts for use in future testing are recommended. A design study was conducted to select a suitable motion picture camera, to select the camera location, and to prepare engineering drawings sufficient to permit installation of the camera. Ten locations on the air vehicle were evaluated before the selection of the location in the horizontal stabilizer actuator fairing. The considerations included cost, camera angle, available volume, environmental control, flutter impact, and interference with antennas or other instrumentation.

Domain-specific languages and diagram customization for a concurrent engineering environment

NASA Astrophysics Data System (ADS)

Cole, B.; Dubos, G.; Banazadeh, P.; Reh, J.; Case, K.; Wang, Y.; Jones, S.; Picha, F.

A major open question for advocates of Model-Based Systems Engineering (MBSE) is the question of how system and subsystem engineers will work together. The Systems Modeling Language (SysML), like any language intended for a large audience, is in tension between the desires for simplicity and for expressiveness. In order to be more expressive, many specialized language elements may be introduced, which will unfortunately make a complete understanding of the language a more daunting task. While this may be acceptable for systems modelers, it will increase the challenge of including subsystem engineers in the modeling effort. One possible answer to this situation is the use of Domain-Specific Languages (DSL), which are fully supported by the Unified Modeling Language (UML). SysML is in fact a DSL for systems engineering. The expressive power of a DSL can be enhanced through the use of diagram customization. Various domains have already developed their own schematic vocabularies. Within the space engineering community, two excellent examples are the propulsion and telecommunication subsystems. A return to simple box-and-line diagrams (e.g., the SysML Internal Block Diagram) are in many ways a step backward. In order allow subsystem engineers to contribute directly to the model, it is necessary to make a system modeling tool at least approximate in accessibility to drawing tools like Microsoft PowerPoint and Visio. The challenge is made more extreme in a concurrent engineering environment, where designs must often be drafted in an hour or two. In the case of the Jet Propulsion Laboratory's Team X concurrent design team, a subsystem is specified using a combination of PowerPoint for drawing and Excel for calculation. A pilot has been undertaken in order to meld the drawing portion and the production of master equipment lists (MELs) via a SysML authoring tool, MagicDraw. Team X currently interacts with its customers in a process of sharing presentations. There are severa- inefficiencies that arise from this situation. The first is that a customer team must wait two weeks to a month (which is 2-4 times the duration of most Team X studies themselves) for a finalized, detailed design description. Another is that this information must be re-entered by hand into the set of engineering artifacts and design tools that the mission concept team uses after a study is complete. Further, there is no persistent connection to Team X or institutionally shared formulation design tools and data after a given study, again reducing the direct reuse of designs created in a Team X study. This paper presents the underpinnings of subsystem DSLs as they were developed for this pilot. This includes specialized semantics for different domains as well as the process by which major categories of objects were derived in support of defining the DSLs. The feedback given to us by the domain experts on usability, along with a pilot study with the partial inclusion of these tools is also discussed.

Domain-Specific Languages and Diagram Customization for a Concurrent Engineering Environment

NASA Technical Reports Server (NTRS)

Cole, Bjorn; Dubos, Greg; Banazadeh, Payam; Reh, Jonathan; Case, Kelley; Wang, Yeou-Fang; Jones, Susan; Picha, Frank

2013-01-01

A major open question for advocates of Model-Based Systems Engineering (MBSE) is the question of how system and subsystem engineers will work together. The Systems Modeling Language (SysML), like any language intended for a large audience, is in tension between the desires for simplicity and for expressiveness. In order to be more expressive, many specialized language elements may be introduced, which will unfortunately make a complete understanding of the language a more daunting task. While this may be acceptable for systems modelers, it will increase the challenge of including subsystem engineers in the modeling effort. One possible answer to this situation is the use of Domain-Specific Languages (DSL), which are fully supported by the Unified Modeling Language (UML). SysML is in fact a DSL for systems engineering. The expressive power of a DSL can be enhanced through the use of diagram customization. Various domains have already developed their own schematic vocabularies. Within the space engineering community, two excellent examples are the propulsion and telecommunication subsystems. A return to simple box-and-line diagrams (e.g., the SysML Internal Block Diagram) are in many ways a step backward. In order allow subsystem engineers to contribute directly to the model, it is necessary to make a system modeling tool at least approximate in accessibility to drawing tools like Microsoft PowerPoint and Visio. The challenge is made more extreme in a concurrent engineering environment, where designs must often be drafted in an hour or two. In the case of the Jet Propulsion Laboratory's Team X concurrent design team, a subsystem is specified using a combination of PowerPoint for drawing and Excel for calculation. A pilot has been undertaken in order to meld the drawing portion and the production of master equipment lists (MELs) via a SysML authoring tool, MagicDraw. Team X currently interacts with its customers in a process of sharing presentations. There are several inefficiencies that arise from this situation. The first is that a customer team must wait two weeks to a month (which is 2-4 times the duration of most Team X studies themselves) for a finalized, detailed design description. Another is that this information must be re-entered by hand into the set of engineering artifacts and design tools that the mission concept team uses after a study is complete. Further, there is no persistent connection to Team X or institutionally shared formulation design tools and data after a given study, again reducing the direct reuse of designs created in a Team X study. This paper presents the underpinnings of subsystem DSLs as they were developed for this pilot. This includes specialized semantics for different domains as well as the process by which major categories of objects were derived in support of defining the DSLs. The feedback given to us by the domain experts on usability, along with a pilot study with the partial inclusion of these tools is also discussed.

Recent Advances in LOX / LH2 Propulsion System for Reusable Vehicle Testing

NASA Astrophysics Data System (ADS)

Tokudome, Shinichiro; Naruo, Yoshihiro; Yagishita, Tsuyoshi; Nonaka, Satoshi; Shida, Maki; Mori, Hatsuo; Nakamura, Takeshi

The third-generation vehicle RVT#3 equipped with a pressure-fed engine, which had upgraded in terms of durability enhancement and a LH2 tank of composite material, successfully performed in repeated flight operation tests; and the vehicle reached its maximum flying altitude of 42m in October 2003. The next step for demonstrating entire sequence of full-scale operation is to put a turbopump-fed system into propulsion system. From a result of primary system analysis, we decided to build an expander-cycle engine by diverting a pair of turbopumps, which had built for another research program, to the present study. A combustion chamber with long cylindrical portion adapted to the engine cycle was also newly made. Two captive firing tests have been conducted with two different thrust control methods, following the component tests of combustor and turbopumps separately conducted. A considerable technical issues recognized in the tests were the robustness enhancement of shaft seal design, the adjustment of shaft stiffness, and start-up operation adapted to the specific engine system. Experimental study of GOX/GH2 RCS thrusters have also been started as a part of a conceptual study of the integration of the propulsion system associated with simplification and reliability improvement of the vehicle system.

Hydrogels for precision meniscus tissue engineering: a comprehensive review.

PubMed

Rey-Rico, Ana; Cucchiarini, Magali; Madry, Henning

The meniscus plays a pivotal role to preserve the knee joint homeostasis. Lesions to the meniscus are frequent, have a reduced ability to heal, and may induce tibiofemoral osteoarthritis. Current reconstructive therapeutic options mainly focus on the treatment of lesions in the peripheral vascularized region. In contrast, few approaches are capable of stimulating repair of damaged meniscal tissue in the central, avascular portion. Tissue engineering approaches are of high interest to repair or replace damaged meniscus tissue in this area. Hydrogel-based biomaterials are of special interest for meniscus repair as its inner part contains relatively high proportions of proteoglycans which are responsible for the viscoelastic compressive properties and hydration grade. Hydrogels exhibiting high water content and providing a specific three-dimensional (3D) microenvironment may be engineered to precisely resemble this topographical composition of the meniscal tissue. Different polymers of both natural and synthetic origins have been manipulated to produce hydrogels hosting relevant cell populations for meniscus regeneration and provide platforms for meniscus tissue replacement. So far, these compounds have been employed to design controlled delivery systems of bioactive molecules involved in meniscal reparative processes or to host genetically modified cells as a means to enhance meniscus repair. This review describes the most recent advances on the use of hydrogels as platforms for precision meniscus tissue engineering.

A rotorcraft flight/propulsion control integration study

NASA Technical Reports Server (NTRS)

Ruttledge, D. G. C.

1986-01-01

An eclectic approach was taken to a study of the integration of digital flight and propulsion controls for helicopters. The basis of the evaluation was the current Gen Hel simulation of the UH-60A Black Hawk helicopter with a model of the GE T700 engine. A list of flight maneuver segments to be used in evaluating the effectiveness of such an integrated control system was composed, based on past experience and an extensive survey of the U.S. Army Air-to-Air Combat Test data. A number of possible features of an integrated system were examined and screened. Those that survived the screening were combined into a design that replaced the T700 fuel control and part of the control system in the UH-60A Gen Hel simulation. This design included portions of an existing pragmatic adaptive fuel control designed by the Chandler-Evans Company and an linear quadratic regulator (LQR) based N(p) governor designed by the GE company, combined with changes in the basic Sikorsky Aircraft designed control system. The integrated system exhibited improved total performance in many areas of the flight envelope.

Horizontally opposed trunnion forward engine mount system supported beneath a wing pylon

NASA Technical Reports Server (NTRS)

Seaquist, John D. (Inventor); Culbertson, Chris (Inventor)

2000-01-01

The present invention relates to an engine mount assembly for supporting an aircraft engine in aft-cantilevered position beneath the aircraft wing. The assembly includes a pair forward engine mounts positioned on opposite sides of an integrally formed yoke member wrapped about the upper half of the engine casing. Each side of the yoke is preferably configured as an A-shaped frame member with the bottom portions joining each other and the pylon. To prevent backbone bending of the engine trunnion assembly, the forward engine mounts supported at opposite ends of the yoke engage the casing along its centerline. The trunnion assembly is preferably constructed of high strength titanium machined and/or forged.

An Archeological Overview and Management Plan for the Tarheel Army Missile Plant Alamance County, North Carolina.

DTIC Science & Technology

1984-05-21

factory planning engineer, noted that bedrock lies about 22 feet be- low the surface in the eastern portion of the main plant area, but had not...Carolina Press. Lee, James B. 1983. Personal communication. Factory Planning Engineer, Western Electric Company, Tarheel Army Missile Plant. Lefl1cr, Hugh

Internal combuston engine having separated cylinder head oil drains and crankcase ventilation passages

DOEpatents

Boggs, D.L.; Baraszu, D.J.; Foulkes, D.M.; Gomes, E.G.

1998-12-29

An internal combustion engine includes separated oil drain-back and crankcase ventilation passages. The oil drain-back passages extend from the cylinder head to a position below the top level of oil in the engine`s crankcase. The crankcase ventilation passages extend from passages formed in the main bearing bulkheads from positions above the oil level in the crankcase and ultimately through the cylinder head. Oil dams surrounding the uppermost portions of the crankcase ventilation passages prevent oil from running downwardly through the crankcase ventilation passages. 4 figs.

40. ARAIII Prototype assembly and evaluation building ARA630. East end ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

40. ARA-III Prototype assembly and evaluation building ARA-630. East end and south side of building. Camera facing west. Roof railing is part of demolition preparations. Building beyond ARA-622 is ARA-621. In left of view is reactor building. ARA-607 is low-roofed portion, while high-bay portion is ARA-608. Ineel photo no. 3-27. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

A Keyboard for Underwater Performance Assessment Battery Testing

DTIC Science & Technology

1990-11-08

Applied Engineering . This four button underwater keyboard uses only a small portion of the boards capacity. The cable is connected to the I/O 32 board via a...H.O., by Applied Engineering ) require special programming to work with the IO 32 board. If the boards are accessed directly from Apple Basic with the... Applied Engineering , 1988) is presented in the Appendix. This program will work with either the enhanced or the unenhanced version of the Apple lie. 6

14 CFR 1214.301 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... payload portion of an STS flight(s). (e) Mission specialist. A career NASA astronaut trained and skilled... Office whose responsibilities are most closely related to the particular scientific or engineering...

Physical Science Informatics: Providing Open Science Access to Microheater Array Boiling Experiment Data

NASA Technical Reports Server (NTRS)

McQuillen, John; Green, Robert D.; Henrie, Ben; Miller, Teresa; Chiaramonte, Fran

2014-01-01

The Physical Science Informatics (PSI) system is the next step in this an effort to make NASA sponsored flight data available to the scientific and engineering community, along with the general public. The experimental data, from six overall disciplines, Combustion Science, Fluid Physics, Complex Fluids, Fundamental Physics, and Materials Science, will present some unique challenges. Besides data in textual or numerical format, large portions of both the raw and analyzed data for many of these experiments are digital images and video, requiring large data storage requirements. In addition, the accessible data will include experiment design and engineering data (including applicable drawings), any analytical or numerical models, publications, reports, and patents, and any commercial products developed as a result of the research. This objective of paper includes the following: Present the preliminary layout (Figure 2) of MABE data within the PSI database. Obtain feedback on the layout. Present the procedure to obtain access to this database.

Configuration evaluation and criteria plan. Volume 2: Evaluation critera plan (preliminary). Space Transportation Main Engine (STME) configuration study

NASA Technical Reports Server (NTRS)

Bair, E. K.

1986-01-01

The unbiased selection of the Space Transportation Main Engine (STME) configuration requires that the candidate engines be evaluated against a predetermined set of criteria which must be properly weighted to emphasize critical requirements defined prior to the actual evaluation. The evaluation and selection process involves the following functions: (1) determining if a configuration can satisfy basic STME requirements (yes/no); (2) defining the evaluation criteria; (3) selecting the criteria relative importance or weighting; (4) determining the weighting sensitivities; and (5) establishing a baseline for engine evaluation. The criteria weighting and sensitivities are cost related and are based on mission models and vehicle requirements. The evaluation process is used as a coarse screen to determine the candidate engines for the parametric studies and as a fine screen to determine concept(s) for conceptual design. The criteria used for the coarse and fine screen evaluation process is shown. The coarse screen process involves verifying that the candidate engines can meet the yes/no screening requirements and a semi-subjective quantitative evaluation. The fine screen engines have to meet all of the yes/no screening gates and are then subjected to a detailed evaluation or assessment using the quantitative cost evaluation processes. The option exists for re-cycling a concept through the quantitative portion of the screening and allows for some degree of optimization. The basic vehicle is a two stage LOX/HC, LOX/LH2 parallel burn vehicle capable of placing 150,000 lbs in low Earth orbit (LEO).

Developing the Parachute System for NASA's Orion: An Overview at Inception

NASA Technical Reports Server (NTRS)

Machin, Ricardo; Taylor, Anthony P.; Royall, Paul

2007-01-01

As the Crew Exploration Vehicle (CEV) program developed, NASA decided to provide the parachute portion of the landing system as Government Furnished Equipment (GFE) and designated NASA Johnson Space Center (JSC) as the responsible NASA center based on JSC s past experience with the X-38 program. JSC subsequently chose to have the Engineering Support contractor Jacobs Sverdrup to manage the overall program development. After a detailed source selection process Jacobs chose Irvin Aerospace Inc (Irvin) to provide the parachutes and mortars for the CEV Parachute Assembly System (CPAS). Thus the CPAS development team, including JSC, Jacobs and Irvin has been formed. While development flight testing will have just begun at the time this paper is submitted, a number of significant design decisions relative to the architecture for the manned spacecraft will have been completed. This paper will present an overview of the approach CPAS is taking to providing the parachute system for CEV, including: system requirements, the preliminary design solution, and the planned/completed flight testing.

14 CFR 171.207 - Performance requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

....” (Annex 10 to the Convention on International Civil Aviation) except those portions that pertain to... electronic engineering practices for the desired service. The facility must be checked periodically during...

14 CFR 171.207 - Performance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

....” (Annex 10 to the Convention on International Civil Aviation) except those portions that pertain to... electronic engineering practices for the desired service. The facility must be checked periodically during...

Study of the capacitance technique for measuring high-temperature blade tip clearance on ceramic rotors

NASA Technical Reports Server (NTRS)

Barranger, John P.

1993-01-01

Higher operating temperatures required for increased engine efficiency can be achieved by using ceramic materials for engine components. Ceramic turbine rotors are subject to the same limitations with regard to gas path efficiency as their superalloy predecessors. In this study, a modified frequency-modulation system is proposed for the measurement of blade tip clearance on ceramic rotors. It is expected to operate up to 1370 C (2500 F), the working temperature of present engines with ceramic turbine rotors. The design of the system addresses two special problems associated with nonmetallic blades: the capacitance is less than that of a metal blade and the effects of temperature may introduce uncertainty with regard to the blade tip material composition. To increase capacitance and stabilize the measurement, a small portion of the rotor is modified by the application of 5-micron-thick platinum films. The platinum surfaces on the probe electrodes and rotor that are exposed to the high-velocity gas stream are coated with an additional 10-micron-thick protective ceramic topcoat. A finite-element method is applied to calculate the capacitance as a function of clearance.

Material requirements for the High Speed Civil Transport

NASA Technical Reports Server (NTRS)

Stephens, Joseph R.; Hecht, Ralph J.; Johnson, Andrew M.

1993-01-01

Under NASA-sponsored High Speed Research (HSR) programs, the materials and processing requirements have been identified for overcoming the environmental and economic barriers of the next generation High Speed Civil Transport (HSCT) propulsion system. The long (2 to 5 hours) supersonic cruise portion of the HSCT cycle will place additional durability requirements on all hot section engine components. Low emissions combustor designs will require high temperature ceramic matrix composite liners to meet an emission goal of less than 5g NO(x) per Kg fuel burned. Large axisymmetric and two-dimensional exhaust nozzle designs are now under development to meet or exceed FAR 36 Stage III noise requirements, and will require lightweight, high temperature metallic, intermetallic, and ceramic matrix composites to reduce nozzle weight and meet structural and acoustic component performance goals. This paper describes and discusses the turbomachinery, combustor, and exhaust nozzle requirements of the High Speed Civil Transport propulsion system.

STS-38 Space Shuttle mission report

NASA Technical Reports Server (NTRS)

Camp, David W.; Germany, D. M.; Nicholson, Leonard S.

1991-01-01

The STS-38 Space Shuttle Program Mission Report contains a summary of the vehicle subsystem activities on this thirty-seventh flight of the Space Shuttle and the seventh flight of the Orbiter vehicle Atlantis (OV-104). In addition to the Atlantis vehicle, the flight vehicle consisted of an External Tank (ET) (designated as ET-40/LWT-33), three Space Shuttle main engines (SSME's) (serial numbers 2019, 2022, 2027), and two Solid Rocket Boosters (SRB's), designated as BI-039. The STS-38 mission was a classified Department of Defense mission, and as much, the classified portions of the mission are not presented in this report. The sequence of events for this mission is shown. The significant problems that occurred in the Space Shuttle Orbiter subsystem during the mission are summarized and the official problem tracking list is presented. In addition, each Space Shuttle Orbiter problem is cited in the subsystem discussion.

Design and development of the Cassini main engine assembly Gimbal mechanism

NASA Technical Reports Server (NTRS)

Rudolph, Dale

1996-01-01

Cassini is an international cooperative effort between NASA, which is producing the orbiter spacecraft, the European Space Agency, which is providing the Huygens Probe, and the Italian Space Agency, which is responsible for the spacecraft radio antenna and portions of three scientific experiments. In the U.S., the mission is managed by NASA's Jet Propulsion Laboratory (JPL) in Pasadena, California. Lockheed-Martin successfully bid on the contract to build the PMS (Propulsion Module Subsystem) for this project. The Cassini spacecraft will be launched on an expedition to Saturn in October, 1997. Its mission is to enter orbit around Saturn in July, 2004, and to explore its moons, rings, and magnetic environment for four years. Cassini will carry the Huygens probe, an instrument package equipped with a parachute, which is designed to study the atmosphere and surface of Saturn's largest moon, Titan.

STS-36 Space Shuttle mission report

NASA Technical Reports Server (NTRS)

Mechelay, Joseph E.; Germany, D. M.; Nicholson, Leonard S.

1990-01-01

The STS-36 Space Shuttle Program Mission Report contains a summary of the vehicle subsystem activities on this thirty-fourth flight of the Space Shuttle and the sixth flight of the OV-104 Orbiter vehicle, Atlantis. In addition to the Atlantis vehicle, the flight vehicle consisted of an External Tank (ET) (designated as ET-33/LWT-26), three Space Shuttle main engines (SSME's) (serial numbers 2019, 2030, and 2029), and two Solid Rocket Boosters (SRB's) (designated as BI-036). The STS-36 mission was a classified Department of Defense mission, and as such, the classified portions of the mission are not discussed. The unclassified sequence of events for this mission is shown in tabular form. Summarized are the significant problems that occurred in the Orbiter subsystems during the mission. The official problem tracking list is presented. In addition, each of the Orbiter problems is cited in the subsystem discussion.

How much should I eat? Situational norms affect young women's food intake during meal time.

PubMed

Hermans, Roel C J; Larsen, Junilla K; Herman, C Peter; Engels, Rutger C M E

2012-02-01

Portion size and the intake of others have been found to influence people's food intake. No study, however, has tested the potential influences of both types of situational norms on intake during the same eating occasion. We experimentally tested the effects of manipulating portion size and the intake of others on young women's meal intake during a 20 min eating opportunity. An experimental design with a three (confederate's intake: small, standard, large) by two (portion size: small, standard) between-participants design was used. A total of eighty-five young women participated. Portion size and the confederate's intake both influenced young women's intake. Participants consumed more when offered a larger portion than when offered a smaller portion, and they also ate more when their eating companion ate more. The present results indicate that the effects of portion size and the intake of others were independent but additive. Thus, both types of situational norms might independently guide an individual's intake during a single eating occasion.

40 CFR 86.1912 - How do I determine whether an engine meets the vehicle-pass criteria?

Code of Federal Regulations, 2011 CFR

2011-07-01

... region, will not be added together to make a 30 second or longer event. Exclude any portion of a sampling... section for at least 90 percent of the valid NTE sampling events, as defined in paragraph (b) of this section. For 2007 through 2009 model year engines, the average emissions from every NTE sampling event...

Jet Engine Exhaust Nozzle Flow Effector

NASA Technical Reports Server (NTRS)

Turner, Travis L. (Inventor); Cano, Roberto J. (Inventor); Silox, Richard J. (Inventor); Buehrle, Ralph D. (Inventor); Cagle, Christopher M. (Inventor); Cabell, Randolph H. (Inventor); Hilton, George C. (Inventor)

2014-01-01

A jet engine exhaust nozzle flow effector is a chevron formed with a radius of curvature with surfaces of the flow effector being defined and opposing one another. At least one shape memory alloy (SMA) member is embedded in the chevron closer to one of the chevron's opposing surfaces and substantially spanning from at least a portion of the chevron's root to the chevron's tip.

Reaching Out: Team AETHER

NASA Technical Reports Server (NTRS)

Murphy, Gloria A.

2010-01-01

Embry Riddle Aeronautical University's Daytona Beach Campus Lunabotics Team took the opportunity to share the love of space, engineering and technology through the educational outreach portion of the competition. Through visits to elementary schools and high schools, and through support of science fairs and robotics competitions, younger generations were introduced to space, engineering and robotics. This report documents the outreach activities of team Aether.

Engine Tune-Up Service. Unit 5: Fuel and Carburetion Systems. Student Guide. Automotive Mechanics Curriculum.

ERIC Educational Resources Information Center

Goodson, Ludy

This student guide is for Unit 5, Fuel and Carburetion Systems, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with inspecting and servicing the fuel and carburetion systems. A companion review exercise book and posttests are available separately as CE 031 218-219. An introduction tells how this unit fits…

Jet Engine Exhaust Nozzle Flow Effector

NASA Technical Reports Server (NTRS)

Turner, Travis L. (Inventor); Buehrle, Ralph D. (Inventor); Silcox, Richard J. (Inventor); Cagle, Christopher M. (Inventor); Cabell, Randolph H. (Inventor); Hilton, George C. (Inventor); Cano, Roberto J. (Inventor)

2011-01-01

A jet engine exhaust nozzle flow effector is a chevron formed with a radius of curvature with surfaces of the flow effector being defined and opposing one another. At least one shape memory alloy (SMA) member is embedded in the chevron closer to one of the chevron's opposing surfaces and substantially spanning from at least a portion of the chevron's root to the chevron's tip.

Engine Tune-up Service. Unit 6: Emission Control Systems. Student Guide. Automotive Mechanics Curriculum.

ERIC Educational Resources Information Center

Bacon, E. Miles

This student guide is for Unit 6, Emission Control Systems, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with inspecting, testing, and servicing an emission control system. A companion review exercise book and posttests are available separately as CE 031 221-222. An introduction tells how this unit fits…

Engine Tune-Up Service. Unit 4: Secondary Circuit. Student Guide. Automotive Mechanics Curriculum.

ERIC Educational Resources Information Center

Bacon, E. Miles

This student guide is for Unit 4, Secondary Circuit, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with how to test and service the secondary ignition circuit. A companion review exercise book and posttests are available separately as CE 031 215-216. An introduction tells how this unit fits into the total…

40 CFR 1033.515 - Discrete-mode steady-state emission tests of locomotives and locomotive engines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the provisions of 40 CFR part 1065, subpart F for general pre-test procedures (including engine and... 1065. (b) Begin the test by operating the locomotive over the pre-test portion of the cycle specified... Sample averagingperiod for emissions 1 Pre-test idle Lowest idle setting 10 to 15 3 Not applicable A Low...

40 CFR 1033.515 - Discrete-mode steady-state emission tests of locomotives and locomotive engines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the provisions of 40 CFR part 1065, subpart F for general pre-test procedures (including engine and... 1065. (b) Begin the test by operating the locomotive over the pre-test portion of the cycle specified... Sample averagingperiod for emissions 1 Pre-test idle Lowest idle setting 10 to 15 3 Not applicable A Low...

40 CFR 1033.515 - Discrete-mode steady-state emission tests of locomotives and locomotive engines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the provisions of 40 CFR part 1065, subpart F for general pre-test procedures (including engine and... 1065. (b) Begin the test by operating the locomotive over the pre-test portion of the cycle specified... Sample averagingperiod for emissions 1 Pre-test idle Lowest idle setting 10 to 15 3 Not applicable A Low...

40 CFR 1033.515 - Discrete-mode steady-state emission tests of locomotives and locomotive engines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the provisions of 40 CFR part 1065, subpart F for general pre-test procedures (including engine and... 1065. (b) Begin the test by operating the locomotive over the pre-test portion of the cycle specified... Sample averagingperiod for emissions 1 Pre-test idle Lowest idle setting 10 to 15 3 Not applicable A Low...

40 CFR 1033.515 - Discrete-mode steady-state emission tests of locomotives and locomotive engines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the provisions of 40 CFR part 1065, subpart F for general pre-test procedures (including engine and... 1065. (b) Begin the test by operating the locomotive over the pre-test portion of the cycle specified... Sample averagingperiod for emissions 1 Pre-test idle Lowest idle setting 10 to 15 3 Not applicable A Low...

The use of fault reporting of medical equipment to identify latent design flaws.

PubMed

Flewwelling, C J; Easty, A C; Vicente, K J; Cafazzo, J A

2014-10-01

Poor device design that fails to adequately account for user needs, cognition, and behavior is often responsible for use errors resulting in adverse events. This poor device design is also often latent, and could be responsible for "No Fault Found" (NFF) reporting, in which medical devices sent for repair by clinical users are found to be operating as intended. Unresolved NFF reports may contribute to incident under reporting, clinical user frustration, and biomedical engineering technologist inefficacy. This study uses human factors engineering methods to investigate the relationship between NFF reporting frequency and device usability. An analysis of medical equipment maintenance data was conducted to identify devices with a high NFF reporting frequency. Subsequently, semi-structured interviews and heuristic evaluations were performed in order to identify potential usability issues. Finally, usability testing was conducted in order to validate that latent usability related design faults result in a higher frequency of NFF reporting. The analysis of medical equipment maintenance data identified six devices with a high NFF reporting frequency. Semi-structured interviews, heuristic evaluations and usability testing revealed that usability issues caused a significant portion of the NFF reports. Other factors suspected to contribute to increased NFF reporting include accessory issues, intermittent faults and environmental issues. Usability testing conducted on three of the devices revealed 23 latent usability related design faults. These findings demonstrate that latent usability related design faults manifest themselves as an increase in NFF reporting and that devices containing usability related design faults can be identified through an analysis of medical equipment maintenance data. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

Photocopy of plan (in U.S. Army office of Army Engineers ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Photocopy of plan (in U.S. Army office of Army Engineers plans and drawings, Fort Hancock and Sandy hook proving ground, record group 7, drawer 44, Cartographic and Architectural branc, The National Archives, Washington, DC) Gillespie, G.L., map of a portion of Sandy Hook, NJ showing condition of beach in vicinity of dynamite gun emplacements, 1894 Engineer's wharf - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

Fiber Grating Moisture And Chemical Sensing System

DOEpatents

Schipani, Claudia; Spano, Ennio; Dalle Crode, Domenico

2004-01-27

A vane for a stator of a variable-geometry turbine, in particular for aeronautical engines, has an airfoil profile and a pair of hinge portions, which are carried by the airfoil profile and enable the airfoil profile to be coupled to a support structure of the stator so as to be rotatable about an axis of adjustment; the vane also has internal channels that allow a flow of air to pass through in order to cool the hinge portions.

Admissible Shape Parameters for a Planar Quasi-Static Constraint Mode Tire Model

DTIC Science & Technology

2014-01-21

Journal of Vibration, 1988. 110(1): p. 70-75. 4. Zegelaar, P.W.A.P., H. B., The In-plane Dynamics of Tyres on Uneven Roads . Vehicle System Dynamics...ADDRESS(ES) Vehicle Terrain performance laboratory,Virginia Tech Mechanical Engineering Department,635 Prices Fork Road - MC 0238,Blacksburg,VA,24061...such that the upper portion is in direct contact with the lower portion and there is a discontinuous and dramatic increase in apparent stiffness). A

The Orion Pad Abort 1 Flight Test A Highly Successful Test

NASA Technical Reports Server (NTRS)

Sinclair, Robert; Taylor, Anthony P. (Tony); Johnston, Justin

2011-01-01

The Orion Pad Abort 1 (PA-1) flight test was designed as an early demonstration of the Launch Abort System (LAS) for the Orion capsule. The LAS was designed developed and manufactured by the Lockheed Martin/Orbital Sciences team. At inception it was realized that recovery of the Orion Capsule simulator would be useful from an engineering analysis and data recovery point of view. Additionally this test represented a flight opportunity for the Orion parachute system, which in a real abort would provide final landing deceleration. The Orion parachute program is named CPAS (CEV Parachute Assembly System). Thus CPAS became a part of the PA-1 flight, as a secondary test objective. At program kick off, the CPAS system was in the design state described below. Airbag land landing of the spacecraft was the program baseline. This affected the rigging of the parachutes. The system entry deployment conditions and vehicle mass have both evolved since that original design. It was decided to use the baseline CPAS Generation 1 (Gen 1) parachute system for the recovery of the PA-1 flight. As CPAS was a secondary test objective, the system would be delivered in its developmental state. As the PA-1 program evolved, the parachute recovery system (CPAS) moved from a secondary objective to a more important portion of the program. Tests were added, weights and deployment conditions changed and some hardware portions of the CPAS configuration were not up to the new challenges. Additional tests were added to provide confidence in the developmental system. This paper will review a few of these aspects with the goal of showing some preliminary and qualitative results from what we believe was a highly successful test.

Affordable Rankine Cycle Waste Heat Recovery for Heavy Duty Trucks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subramanian, Swami Nathan

Nearly 30% of fuel energy is not utilized and wasted in the engine exhaust. Organic Rankine Cycle (ORC) based waste heat recovery (WHR) systems offer a promising approach on waste energy recovery and improving the efficiency of Heavy-Duty diesel engines. Major barriers in the ORC WHR system are the system cost and controversial waste heat recovery working fluids. More than 40% of the system cost is from the additional heat exchangers (recuperator, condenser and tail pipe boiler). The secondary working fluid loop designed in ORC system is either flammable or environmentally sensitive. The Eaton team investigated a novel approach tomore » reduce the cost of implementing ORC based WHR systems to Heavy-Duty (HD) Diesel engines while utilizing safest working fluids. Affordable Rankine Cycle (ARC) concept aimed to define the next generation of waste energy recuperation with a cost optimized WHR system. ARC project used engine coolant as the working fluid. This approach reduced the need for a secondary working fluid circuit and subsequent complexity. A portion of the liquid phase engine coolant has been pressurized through a set of working fluid pumps and used to recover waste heat from the exhaust gas recirculation (EGR) and exhaust tail pipe exhaust energy. While absorbing heat, the mixture is partially vaporized but remains a wet binary mixture. The pressurized mixed-phase engine coolant mixture is then expanded through a fixed-volume ratio expander that is compatible with two-phase conditions. Heat rejection is accomplished through the engine radiator, avoiding the need for a separate condenser. The ARC system has been investigated for PACCAR’s MX-13 HD diesel engine.« less

DART system analysis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boggs, Paul T.; Althsuler, Alan; Larzelere, Alex R.

2005-08-01

The Design-through-Analysis Realization Team (DART) is chartered with reducing the time Sandia analysts require to complete the engineering analysis process. The DART system analysis team studied the engineering analysis processes employed by analysts in Centers 9100 and 8700 at Sandia to identify opportunities for reducing overall design-through-analysis process time. The team created and implemented a rigorous analysis methodology based on a generic process flow model parameterized by information obtained from analysts. They also collected data from analysis department managers to quantify the problem type and complexity distribution throughout Sandia's analyst community. They then used this information to develop a communitymore » model, which enables a simple characterization of processes that span the analyst community. The results indicate that equal opportunity for reducing analysis process time is available both by reducing the ''once-through'' time required to complete a process step and by reducing the probability of backward iteration. In addition, reducing the rework fraction (i.e., improving the engineering efficiency of subsequent iterations) offers approximately 40% to 80% of the benefit of reducing the ''once-through'' time or iteration probability, depending upon the process step being considered. Further, the results indicate that geometry manipulation and meshing is the largest portion of an analyst's effort, especially for structural problems, and offers significant opportunity for overall time reduction. Iteration loops initiated late in the process are more costly than others because they increase ''inner loop'' iterations. Identifying and correcting problems as early as possible in the process offers significant opportunity for time savings.« less

Revisiting software specification and design for large astronomy projects

NASA Astrophysics Data System (ADS)

Wiant, Scott; Berukoff, Steven

2016-07-01

The separation of science and engineering in the delivery of software systems overlooks the true nature of the problem being solved and the organization that will solve it. Use of a systems engineering approach to managing the requirements flow between these two groups as between a customer and contractor has been used with varying degrees of success by well-known entities such as the U.S. Department of Defense. However, treating science as the customer and engineering as the contractor fosters unfavorable consequences that can be avoided and opportunities that are missed. For example, the "problem" being solved is only partially specified through the requirements generation process since it focuses on detailed specification guiding the parties to a technical solution. Equally important is the portion of the problem that will be solved through the definition of processes and staff interacting through them. This interchange between people and processes is often underrepresented and under appreciated. By concentrating on the full problem and collaborating on a strategy for its solution a science-implementing organization can realize the benefits of driving towards common goals (not just requirements) and a cohesive solution to the entire problem. The initial phase of any project when well executed is often the most difficult yet most critical and thus it is essential to employ a methodology that reinforces collaboration and leverages the full suite of capabilities within the team. This paper describes an integrated approach to specifying the needs induced by a problem and the design of its solution.

Lessons learned for composite structures

NASA Technical Reports Server (NTRS)

Whitehead, R. S.

1991-01-01

Lessons learned for composite structures are presented in three technology areas: materials, manufacturing, and design. In addition, future challenges for composite structures are presented. Composite materials have long gestation periods from the developmental stage to fully matured production status. Many examples exist of unsuccessful attempts to accelerate this gestation period. Experience has shown that technology transition of a new material system to fully matured production status is time consuming, involves risk, is expensive and should not be undertaken lightly. The future challenges for composite materials require an intensification of the science based approach to material development, extension of the vendor/customer interaction process to include all engineering disciplines of the end user, reduced material costs because they are a significant factor in overall part cost, and improved batch-to-batch pre-preg physical property control. Historical manufacturing lessons learned are presented using current in-service production structure as examples. Most producibility problems for these structures can be traced to their sequential engineering design. This caused an excessive emphasis on design-to-weight and schedule at the expense of design-to-cost. This resulted in expensive performance originated designs, which required costly tooling and led to non-producible parts. Historically these problems have been allowed to persist throughout the production run. The current/future approach for the production of affordable composite structures mandates concurrent engineering design where equal emphasis is placed on product and process design. Design for simplified assembly is also emphasized, since assembly costs account for a major portion of total airframe costs. The future challenge for composite manufacturing is, therefore, to utilize concurrent engineering in conjunction with automated manufacturing techniques to build affordable composite structures. Composite design experience has shown that significant weight savings have been achieved, outstanding fatigue and corrosion resistance have been demonstrated, and in-service performance has been very successful. Currently no structural design show stoppers exist for composite structures. A major lesson learned is that the full scale static test is the key test for composites, since it is the primary structural 'hot spot' indicator. The major durability issue is supportability of thin skinned structure. Impact damage has been identified as the most significant issue for the damage tolerance control of composite structures. However, delaminations induced during assembly operations have demonstrated a significant nuisance value. The future challenges for composite structures are threefold. Firstly, composite airframe weight fraction should increase to 60 percent. At the same time, the cost of composite structures must be reduced by 50 percent to attain the goal of affordability. To support these challenges it is essential to develop lower cost materials and processes.

Cook/chill foodservice system with a microwave oven: aerobic plate counts from beef loaf, potatoes and frozen green beans.

PubMed

Dahl, C A; Matthews, M E; Marth, E H

1980-06-01

The purpose was to evaluate microbiological quality and end temperature (ET) of portioned food after heating in a microwave oven as used in a hospital cook/chill foodservice system. Beef loaf (15 kg), potatoes (6 kg), and green beans (5 kg) were prepared in a laboratory. After initial cooking to 60 degrees C, and storage (7 degrees C for 24 h), beef loaf (100 g) was microwave heated: 20, 50, 80 or 110 s. Potatoes were reconstituted, stored (7 degrees C for 24 h), portioned (100 g/portion), and microwave-heated: 25, 45, 65 or 84 s. Beans were thawed (7 degrees C for 24 h), portioned (100 g/portion), and microwave-heated: 20, 50, 80 or 110 s. Aerobic plate counts (APC) for foods were obtained throughout product flow. Wide ranges of Et and of APC in foods indicates that research is needed, for greater control of microwave-heating through advanced microwave engineering and food technology, to produce food with constant microbiological quality.

Sandia National Laboratories Facilities Management and Operations Center Design Standards Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Timothy L.

2014-09-01

At Sandia National Laboratories in New Mexico (SNL/NM), the design, construction, operation, and maintenance of facilities is guided by industry standards, a graded approach, and the systematic analysis of life cycle benefits received for costs incurred. The design of the physical plant must ensure that the facilities are "fit for use," and provide conditions that effectively, efficiently, and safely support current and future mission needs. In addition, SNL/NM applies sustainable design principles, using an integrated whole-building design approach, from site planning to facility design, construction, and operation to ensure building resource efficiency and the health and productivity of occupants. Themore » safety and health of the workforce and the public, any possible effects on the environment, and compliance with building codes take precedence over project issues, such as performance, cost, and schedule. These design standards generally apply to all disciplines on all SNL/NM projects. Architectural and engineering design must be both functional and cost-effective. Facility design must be tailored to fit its intended function, while emphasizing low-maintenance, energy-efficient, and energy-conscious design. Design facilities that can be maintained easily, with readily accessible equipment areas, low maintenance, and quality systems. To promote an orderly and efficient appearance, architectural features of new facilities must complement and enhance the existing architecture at the site. As an Architectural and Engineering (A/E) professional, you must advise the Project Manager when this approach is prohibitively expensive. You are encouraged to use professional judgment and ingenuity to produce a coordinated interdisciplinary design that is cost-effective, easily contractible or buildable, high-performing, aesthetically pleasing, and compliant with applicable building codes. Close coordination and development of civil, landscape, structural, architectural, fire protection, mechanical, electrical, telecommunications, and security features is expected to ensure compatibility with planned functional equipment and to facilitate constructability. If portions of the design are subcontracted to specialists, delivery of the finished design documents must not be considered complete until the subcontracted portions are also submitted for review. You must, along with support consultants, perform functional analyses and programming in developing design solutions. These solutions must reflect coordination of the competing functional, budgetary, and physical requirements for the project. During design phases, meetings between you and the SNL/NM Project Team to discuss and resolve design issues are required. These meetings are a normal part of the design process. For specific design-review requirements, see the project-specific Design Criteria. In addition to the design requirements described in this manual, instructive information is provided to explain the sustainable building practice goals for design, construction, operation, and maintenance of SNL/NM facilities. Please notify SNL/NM personnel of design best practices not included in this manual, so they can be incorporated in future updates. You must convey all documents describing work to the SNL/NM Project Manager in both hard copy and in an electronic format compatible with the SNL/NM-prescribed CADD and other software packages, and in accordance with a SNL/NM approved standard format. Print all hard copy versions of submitted documents (excluding drawings and renderings) double-sided when practical.« less

Emerging CFD technologies and aerospace vehicle design

NASA Technical Reports Server (NTRS)

Aftosmis, Michael J.

1995-01-01

With the recent focus on the needs of design and applications CFD, research groups have begun to address the traditional bottlenecks of grid generation and surface modeling. Now, a host of emerging technologies promise to shortcut or dramatically simplify the simulation process. This paper discusses the current status of these emerging technologies. It will argue that some tools are already available which can have positive impact on portions of the design cycle. However, in most cases, these tools need to be integrated into specific engineering systems and process cycles to be used effectively. The rapidly maturing status of unstructured and Cartesian approaches for inviscid simulations makes suggests the possibility of highly automated Euler-boundary layer simulations with application to loads estimation and even preliminary design. Similarly, technology is available to link block structured mesh generation algorithms with topology libraries to avoid tedious re-meshing of topologically similar configurations. Work in algorithmic based auto-blocking suggests that domain decomposition and point placement operations in multi-block mesh generation may be properly posed as problems in Computational Geometry, and following this approach may lead to robust algorithmic processes for automatic mesh generation.

New Approaches to HSCT Multidisciplinary Design and Optimization

NASA Technical Reports Server (NTRS)

Schrage, D. P.; Craig, J. I.; Fulton, R. E.; Mistree, F.

1996-01-01

The successful development of a capable and economically viable high speed civil transport (HSCT) is perhaps one of the most challenging tasks in aeronautics for the next two decades. At its heart it is fundamentally the design of a complex engineered system that has significant societal, environmental and political impacts. As such it presents a formidable challenge to all areas of aeronautics, and it is therefore a particularly appropriate subject for research in multidisciplinary design and optimization (MDO). In fact, it is starkly clear that without the availability of powerful and versatile multidisciplinary design, analysis and optimization methods, the design, construction and operation of im HSCT simply cannot be achieved. The present research project is focused on the development and evaluation of MDO methods that, while broader and more general in scope, are particularly appropriate to the HSCT design problem. The research aims to not only develop the basic methods but also to apply them to relevant examples from the NASA HSCT R&D effort. The research involves a three year effort aimed first at the HSCT MDO problem description, next the development of the problem, and finally a solution to a significant portion of the problem.

Sensor failure detection for jet engines

NASA Technical Reports Server (NTRS)

Beattie, E. C.; Laprad, R. F.; Akhter, M. M.; Rock, S. M.

1983-01-01

Revisions to the advanced sensor failure detection, isolation, and accommodation (DIA) algorithm, developed under the sensor failure detection system program were studied to eliminate the steady state errors due to estimation filter biases. Three algorithm revisions were formulated and one revision for detailed evaluation was chosen. The selected version modifies the DIA algorithm to feedback the actual sensor outputs to the integral portion of the control for the nofailure case. In case of a failure, the estimates of the failed sensor output is fed back to the integral portion. The estimator outputs are fed back to the linear regulator portion of the control all the time. The revised algorithm is evaluated and compared to the baseline algorithm developed previously.

Laser ignition

DOEpatents

Early, James W.; Lester, Charles S.

2002-01-01

In the apparatus of the invention, a first excitation laser or other excitation light source is used in tandem with an ignitor laser to provide a compact, durable, engine deployable fuel ignition laser system. Reliable fuel ignition is provided over a wide range of fuel conditions by using a single remote excitation light source for one or more small lasers located proximate to one or more fuel combustion zones. In the embodiment of the invention claimed herein, the beam from the excitation light source is split with a portion of it going to the ignitor laser and a second portion of it being combined with either the first portion after a delay before injection into the ignitor laser.

Computational Investigation of a Boundary-Layer Ingesting Propulsion System for the Common Research Model

NASA Technical Reports Server (NTRS)

Blumenthal, Brennan T.; Elmiligui, Alaa; Geiselhart, Karl A.; Campbell, Richard L.; Maughmer, Mark D.; Schmitz, Sven

2016-01-01

The present paper examines potential propulsive and aerodynamic benefits of integrating a Boundary-Layer Ingestion (BLI) propulsion system into a typical commercial aircraft using the Common Research Model (CRM) geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment is used to generate engine conditions for CFD analysis. Improvements to the BLI geometry are made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method, and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2 deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.4% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from Boundary-Layer Ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.

Computational Investigation of a Boundary-Layer Ingestion Propulsion System for the Common Research Model

NASA Technical Reports Server (NTRS)

Blumenthal, Brennan

2016-01-01

This thesis will examine potential propulsive and aerodynamic benefits of integrating a boundary-layer ingestion (BLI) propulsion system with a typical commercial aircraft using the Common Research Model geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment will be used to generate engine conditions for CFD analysis. Improvements to the BLI geometry will be made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.3% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from boundary-layer ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.

NASA's Advanced Propulsion Technology Activities for Third Generation Fully Reusable Launch Vehicle Applications

NASA Technical Reports Server (NTRS)

Hueter, Uwe

2000-01-01

NASA's Office of Aeronautics and Space Transportation Technology (OASTT) established the following three major goals, referred to as "The Three Pillars for Success": Global Civil Aviation, Revolutionary Technology Leaps, and Access to Space. The Advanced Space Transportation Program Office (ASTP) at the NASA's Marshall Space Flight Center in Huntsville, Ala. focuses on future space transportation technologies under the "Access to Space" pillar. The Propulsion Projects within ASTP under the investment area of Spaceliner100, focus on the earth-to-orbit (ETO) third generation reusable launch vehicle technologies. The goals of Spaceliner 100 is to reduce cost by a factor of 100 and improve safety by a factor of 10,000 over current conditions. The ETO Propulsion Projects in ASTP, are actively developing combination/combined-cycle propulsion technologies that utilized airbreathing propulsion during a major portion of the trajectory. System integration, components, materials and advanced rocket technologies are also being pursued. Over the last several years, one of the main thrusts has been to develop rocket-based combined cycle (RBCC) technologies. The focus has been on conducting ground tests of several engine designs to establish the RBCC flowpaths performance. Flowpath testing of three different RBCC engine designs is progressing. Additionally, vehicle system studies are being conducted to assess potential operational space access vehicles utilizing combined-cycle propulsion systems. The design, manufacturing, and ground testing of a scale flight-type engine are planned. The first flight demonstration of an airbreathing combined cycle propulsion system is envisioned around 2005. The paper will describe the advanced propulsion technologies that are being being developed under the ETO activities in the ASTP program. Progress, findings, and future activities for the propulsion technologies will be discussed.

A Nuclear Ramjet Flyer for Exploration of Jovian Atmosphere

NASA Astrophysics Data System (ADS)

Maise, G.; Powell, J.; Paniagua, J.; Lecat, R.

2001-01-01

We investigated the design, operation, and data gathering possibilities of a nuclear-powered ramjet flyer in the Jovian atmosphere. The MITEE nuclear rocket engine can be modified to operate as a ramjet in planetary atmospheres. (Note: MITEE is a compact, ultra-light-weight thermal nuclear rocket which uses hydrogen as the propellant.) To operate as a ramjet, MITEE requires a suitable inlet and diffuser to substitute for the propellant that is pumped from the supply tanks in a nuclear rocket engine. Such a ramjet would fly in the upper Jovian atmosphere, mapping in detail temperatures, pressures, compositions, lightning activity, and wind speeds in the highly turbulent equatorial zone and the Great Red Spot. The nuclear ramjet could operate for months because: (1) the Jovian atmosphere has unlimited propellant, (2) the MITEE nuclear reactor is a (nearly) unlimited power source, and (3) with few moving parts, mechanical wear should be minimal. This paper presents a conceptual design of a ramjet flyer and its nuclear engine. The flyer incorporates a swept-wing design with instruments located in the twin wing-tip pods (away from the radiation source and readily shielded, if necessary). The vehicle is 2 m long with a 2 m wingspan. Its mass is 220 kg, and its nominal flight Mach number is 1.5. Based on combined neutronic and thermal/hydraulic analyses, we calculated that the ambient pressure range over which the flyer can operate to be from about 0.04 to 4 (terrestrial) atmospheres. This altitude range encompasses the three uppermost cloud layers in the Jovian atmosphere: (1) the entire uppermost visible NH3 ice cloud layer (where lightning has been observed), (2) the entire NH4HS ice cloud layer, and (3) the upper portion of the H2O ice cloud layer.

Low Reynolds number kappa-epsilon and empirical transition models for oscillatory pipe flow and heat transfer. M.S. Thesis

NASA Technical Reports Server (NTRS)

Bauer, Christopher

1993-01-01

Stirling engine heat exchangers are shell-and-tube type with oscillatory flow (zero-mean velocity) for the inner fluid. This heat transfer process involves laminar-transition turbulent flow motions under oscillatory flow conditions. A low Reynolds number kappa-epsilon model, (Lam-Bremhorst form), was utilized in the present study to simulate fluid flow and heat transfer in a circular tube. An empirical transition model was used to activate the low Reynolds number k-e model at the appropriate time within the cycle for a given axial location within the tube. The computational results were compared with experimental flow and heat transfer data for: (1) velocity profiles, (2) kinetic energy of turbulence, (3) skin friction factor, (4) temperature profiles, and (5) wall heat flux. The experimental data were obtained for flow in a tube (38 mm diameter and 60 diameter long), with the maximum Reynolds number based on velocity being Re(sub max) = 11840, a dimensionless frequency (Valensi number) of Va = 80.2, at three axial locations X/D = 16, 30 and 44. The agreement between the computations and the experiment is excellent in the laminar portion of the cycle and good in the turbulent portion. Moreover, the location of transition was predicted accurately. The Low Reynolds Number kappa-epsilon model, together with an empirical transition model, is proposed herein to generate the wall heat flux values at different operating parameters than the experimental conditions. Those computational data can be used for testing the much simpler and less accurate one dimensional models utilized in 1-D Stirling Engine design codes.

Engine Tune-Up Service. Unit 3: Primary Circuit. Student Guide. Automotive Mechanics Curriculum.

ERIC Educational Resources Information Center

Bacon, E. Miles

This student guide is for Unit 3, Primary Circuit, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with how to test the primary ignition circuit. A companion review exercise book and posttests are available separately as CE 031 212-213. An introduction tells how this unit fits into the total tune-up service,…

Engine Tune-up Service. Unit 2: Charging System. Student Guide. Automotive Mechanics Curriculum.

ERIC Educational Resources Information Center

Richardson, Roger L.; Bacon, E. Miles

This student guide is for Unit 2, Charging System, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with how to test the charging system. A companion review exercise book and posttests are available separately as CE 031 209-210. An introduction tells how this unit fits into the total tune-up service, defines…

Engineering Techniques for Electromagnetic Pulse-Hardness Testing.

DTIC Science & Technology

electromagnetic pulse (EMP). The text describes energy sources, simulation techniques, test instrumentation, and testing techniques. Emphasis is on testing that can be accomplished by engineers with knowledge of electromagnetics and circuits. Complicated systems that require special expertise are described only to acquaint the reader with their characteristics. This text is intended to supplement the testing portion of DNA 2772T ’DNA EMP Awareness Course Notes.’

The Modular Clock Algorithm for Blind Rendezvous

DTIC Science & Technology

2009-03-26

and Computer Engineering Graduate School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training...capabilities in spectrum management and particularly in harvesting unused portions of pre-allocated band- width under DSA. The term “cognitive radio” was...of rendezvous and our role as the waiter . However, if the “child” refuses to move from non-common spectrum, rendezvous cannot occur. Bluetooth

Photonically engineered incandescent emitter

DOEpatents

Gee, James M.; Lin, Shawn-Yu; Fleming, James G.; Moreno, James B.

2003-08-26

A photonically engineered incandescence is disclosed. The emitter materials and photonic crystal structure can be chosen to modify or suppress thermal radiation above a cutoff wavelength, causing the emitter to selectively emit in the visible and near-infrared portions of the spectrum. An efficient incandescent lamp is enabled thereby. A method for fabricating a three-dimensional photonic crystal of a structural material, suitable for the incandescent emitter, is also disclosed.

Photonically Engineered Incandescent Emitter

DOEpatents

Gee, James M.; Lin, Shawn-Yu; Fleming, James G.; Moreno, James B.

2005-03-22

A photonically engineered incandescence is disclosed. The emitter materials and photonic crystal structure can be chosen to modify or suppress thermal radiation above a cutoff wavelength, causing the emitter to selectively emit in the visible and near-infrared portions of the spectrum. An efficient incandescent lamp is enabled thereby. A method for fabricating a three-dimensional photonic crystal of a structural material, suitable for the incandescent emitter, is also disclosed.

Alternate space shuttle concepts study. Part 2: Technical summary. Volume 2: Orbiter definition

NASA Technical Reports Server (NTRS)

1971-01-01

A study was conducted of a three-engined external hydrogen tank orbiter/heat sink booster utilizing 415 K sea level thrust engines. The results of the study, pertaining to the orbiter portion of the configuration, are presented. A complete summary of characteristics is given for the external tank configuration along with some comparative data for a conventional internal tank configuration.

Finding of No Significant Impact for the Missouri River Recovery Program Lower Little Sioux Bend Shallow Water Habitat Construction Project

DTIC Science & Technology

2011-07-01

A relatively small portion of this accreted land would be removed by the proposed project and returned to the River. U.S. Army Corps of Engineers... Planting a portion of the site currently utilized for row-crop agriculture to native hardwood tree species. • Gradual sloping of the new River...the change would be localized and so small that it would not be of any measurable or perceptible consequence. Minor: Impact could result in a

Geothermal Potential of Marine Corps Air Station, Yuma, Arizona, and the Western Portion of Luke-Williams Gunnery Range

DTIC Science & Technology

1988-01-01

region appears to be a temporal as well as a spatial transition zone between the emplacement of the majority of the Arizona porphyry coppers during... Porphyry Copper Deposits of the Western Hemisphere. American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 1978, 219 pp. 30. U.S...NWC TP 6827 S Geothermal Potential of Marine Corps Air Station, Yuma, Arizona , and the Western Portion of Luke-Williams Gunnery Range by Steven C

Regional Supplement to the Corps of Engineers Wetland Delineation Manual: Midwest Region (Version 2.0)

DTIC Science & Technology

2010-08-01

2. Saplings and shrubs – 15-ft (4.6-m) radius 3. Herbaceous plants – 5-ft (1.5-m) radius or 3.28- by 3.28-ft square (1-m2) quadrat 4. Woody vines ...This supplement is applicable to the Midwest Region, which consists of all or portions of 14 states: Illinois, Indiana , Iowa, Kansas, Kentucky...This supplement is applicable to the Midwest Region, which consists of all or portions of 14 states: Illinois, Indiana , Iowa, Kansas, Kentucky

How Fo-ATPase generates rotary torque.

PubMed

Oster, G; Wang, H; Grabe, M

2000-04-29

The F-ATPases synthesize ATP using a transmembrane ionmotive force (IMF) established by the electron transport chain. This transduction involves first converting the IMF to a rotary torque in the transmembrane Fo portion. This torque is communicated from Fo to the F1 portion where the energy is used to release the newly synthesized ATP from the catalytic sites according to Boyer's binding change mechanism. Here we explain the principle by which an IMF generates this rotary torque in the Fo ion engine.

28 CFR 91.55 - Categorical exclusions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... an approved State Coastal Zone Management Program, a coastal barrier or a portion of a barrier within the Coastal Barrier Resources System, a river or portion of a river included in or designated for... source aquifer recharge area designated by the Environmental Protection Agency (EPA). The resulting...

Endochondral Ossification for Enhancing Bone Regeneration: Converging Native Extracellular Matrix Biomaterials and Developmental Engineering In Vivo

PubMed Central

Dennis, S. Connor; Berkland, Cory J.; Bonewald, Lynda F.

2015-01-01

Autologous bone grafting (ABG) remains entrenched as the gold standard of treatment in bone regenerative surgery. Consequently, many marginally successful bone tissue engineering strategies have focused on mimicking portions of ABG's “ideal” osteoconductive, osteoinductive, and osteogenic composition resembling the late reparative stage extracellular matrix (ECM) in bone fracture repair, also known as the “hard” or “bony” callus. An alternative, less common approach that has emerged in the last decade harnesses endochondral (EC) ossification through developmental engineering principles, which acknowledges that the molecular and cellular mechanisms involved in developmental skeletogenesis, specifically EC ossification, are closely paralleled during native bone healing. EC ossification naturally occurs during the majority of bone fractures and, thus, can potentially be utilized to enhance bone regeneration for nearly any orthopedic indication, especially in avascular critical-sized defects where hypoxic conditions favor initial chondrogenesis instead of direct intramembranous ossification. The body's native EC ossification response, however, is not capable of regenerating critical-sized defects without intervention. We propose that an underexplored potential exists to regenerate bone through the native EC ossification response by utilizing strategies which mimic the initial inflammatory or fibrocartilaginous ECM (i.e., “pro-” or “soft” callus) observed in the early reparative stage of bone fracture repair. To date, the majority of strategies utilizing this approach rely on clinically burdensome in vitro cell expansion protocols. This review will focus on the confluence of two evolving areas, (1) native ECM biomaterials and (2) developmental engineering, which will attempt to overcome the technical, business, and regulatory challenges that persist in the area of bone regeneration. Significant attention will be given to native “raw” materials and ECM-based designs that provide necessary osteo- and chondro-conductive and inductive features for enhancing EC ossification. In addition, critical perspectives on existing stem cell-based therapeutic strategies will be discussed with a focus on their use as an extension of the acellular ECM-based designs for specific clinical indications. Within this framework, a novel realm of unexplored design strategies for bone tissue engineering will be introduced into the collective consciousness of the regenerative medicine field. PMID:25336144

Requirements Analysis Study for Master Pump Shutdown System Project Development Specification [SEC 1 and 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

BEVINS, R.R.

This document has been updated during the definitive design portion of the first phase of the W-314 Project to capture additional software requirements and is planned to be updated during the second phase of the W-314 Project to cover the second phase of the Project's scope. The objective is to provide requirement traceability by recording the analysis/basis for the functional descriptions of the master pump shutdown system. This document identifies the sources of the requirements and/or how these were derived. Each requirement is validated either by quoting the source or an analysis process involving the required functionality, performance characteristics, operationsmore » input or engineering judgment.« less

Small transport aircraft technology

NASA Technical Reports Server (NTRS)

Williams, L. J.

1983-01-01

Information on commuter airline trends and aircraft developments is provided to upgrade the preliminary findings of a NASA-formed small transport aircraft technology (STAT) team, established to determine whether the agency's research and development programs could help commuter aircraft manufacturers solve technical problems related to passenger acceptance and use of 19- to 50-passenger aircraft. The results and conclusions of the full set of completed STAT studies are presented. These studies were performed by five airplane manufacturers, five engine manufacturers, and two propeller manufacturers. Those portions of NASA's overall aeronautics research and development programs which are applicable to commuter aircraft design are summarized. Areas of technology that might beneficially be expanded or initiated to aid the US commuter aircraft manufacturers in the evolution of improved aircraft for the market are suggested.

Children's accuracy of portion size estimation using digital food images: effects of interface design and size of image on computer screen.

PubMed

Baranowski, Tom; Baranowski, Janice C; Watson, Kathleen B; Martin, Shelby; Beltran, Alicia; Islam, Noemi; Dadabhoy, Hafza; Adame, Su-heyla; Cullen, Karen; Thompson, Debbe; Buday, Richard; Subar, Amy

2011-03-01

To test the effect of image size and presence of size cues on the accuracy of portion size estimation by children. Children were randomly assigned to seeing images with or without food size cues (utensils and checked tablecloth) and were presented with sixteen food models (foods commonly eaten by children) in varying portion sizes, one at a time. They estimated each food model's portion size by selecting a digital food image. The same food images were presented in two ways: (i) as small, graduated portion size images all on one screen or (ii) by scrolling across large, graduated portion size images, one per sequential screen. Laboratory-based with computer and food models. Volunteer multi-ethnic sample of 120 children, equally distributed by gender and ages (8 to 13 years) in 2008-2009. Average percentage of correctly classified foods was 60·3 %. There were no differences in accuracy by any design factor or demographic characteristic. Multiple small pictures on the screen at once took half the time to estimate portion size compared with scrolling through large pictures. Larger pictures had more overestimation of size. Multiple images of successively larger portion sizes of a food on one computer screen facilitated quicker portion size responses with no decrease in accuracy. This is the method of choice for portion size estimation on a computer.

Real-time simulation of the TF30-P-3 turbofan engine using a hybrid computer

NASA Technical Reports Server (NTRS)

Szuch, J. R.; Bruton, W. M.

1974-01-01

A real-time, hybrid-computer simulation of the TF30-P-3 turbofan engine was developed. The simulation was primarily analog in nature but used the digital portion of the hybrid computer to perform bivariate function generation associated with the performance of the engine's rotating components. FORTRAN listings and analog patching diagrams are provided. The hybrid simulation was controlled by a digital computer programmed to simulate the engine's standard hydromechanical control. Both steady-state and dynamic data obtained from the digitally controlled engine simulation are presented. Hybrid simulation data are compared with data obtained from a digital simulation provided by the engine manufacturer. The comparisons indicate that the real-time hybrid simulation adequately matches the baseline digital simulation.

Indirect synthesis of multidegree-of-freedom transient systems

NASA Technical Reports Server (NTRS)

Chen, Y. H.; Pilkey, W. D.; Kalinowski, A. J.

1976-01-01

The indirect synthesis method is developed and shown to be capable of leading a near-optimal design of multidegree-of-freedom and multidesign-element transient nonlinear dynamical systems. The basis of the approach is to select the open design parameters such that the response of the portion of the system being designed approximates the limiting performances solution. The limiting performance problem can be formulated as one of linear programming by replacing all portions of the system subject to transient disturbances by control forces and supposing that the remaining portions are linear as are the overall kinematic constraints. One then selects the design parameters that respond most closely to the limiting performance solution, which can be achieved by unconstrained curve-fitting techniques.

Internal combustion engine having a reactor for afterburning of unburned exhaust gas constituents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maurhoff, G.; Steinwart, J.

1974-08-07

An internal combustion engine is described which has an engine housing and a reactor for afterburning of unburned constituents in the exhaust gas. The reactor has a shell with a periphery and contains a heat-insulated, reactor chamber which is freely movable beyond the point of connection to the shell. The reactor has an inlet nozzle extending freely through the shell and connected to an outlet passage of the engine and has an outlet for escape of the exhaust gases from the reactor chamber. The inlet nozzle protrudes freely into the outlet passage, and the shell has a portion around themore » inlet nozzle in contact with the engine housing.« less

Gas turbine engine adapted for use in combination with an apparatus for separating a portion of oxygen from compressed air

DOEpatents

Bland, Robert J [Oviedo, FL; Horazak, Dennis A [Orlando, FL

2012-03-06

A gas turbine engine is provided comprising an outer shell, a compressor assembly, at least one combustor assembly, a turbine assembly and duct structure. The outer shell includes a compressor section, a combustor section, an intermediate section and a turbine section. The intermediate section includes at least one first opening and at least one second opening. The compressor assembly is located in the compressor section to define with the compressor section a compressor apparatus to compress air. The at least one combustor assembly is coupled to the combustor section to define with the combustor section a combustor apparatus. The turbine assembly is located in the turbine section to define with the turbine section a turbine apparatus. The duct structure is coupled to the intermediate section to receive at least a portion of the compressed air from the compressor apparatus through the at least one first opening in the intermediate section, pass the compressed air to an apparatus for separating a portion of oxygen from the compressed air to produced vitiated compressed air and return the vitiated compressed air to the intermediate section via the at least one second opening in the intermediate section.

Orion Flight Performance Design Trades

NASA Technical Reports Server (NTRS)

Jackson, Mark C.; Straube, Timothy

2010-01-01

A significant portion of the Orion pre-PDR design effort has focused on balancing mass with performance. High level performance metrics include abort success rates, lunar surface coverage, landing accuracy and touchdown loads. These metrics may be converted to parameters that affect mass, such as ballast for stabilizing the abort vehicle, propellant to achieve increased lunar coverage or extended missions, or ballast to increase the lift-to-drag ratio to improve entry and landing performance. The Orion Flight Dynamics team was tasked to perform analyses to evaluate many of these trades. These analyses not only provide insight into the physics of each particular trade but, in aggregate, they illustrate the processes used by Orion to balance performance and mass margins, and thereby make design decisions. Lessons learned can be gleaned from a review of these studies which will be useful to other spacecraft system designers. These lessons fall into several categories, including: appropriate application of Monte Carlo analysis in design trades, managing margin in a highly mass-constrained environment, and the use of requirements to balance margin between subsystems and components. This paper provides a review of some of the trades and analyses conducted by the Flight Dynamics team, as well as systems engineering lessons learned.

Internal combuston engine having separated cylinder head oil drains and crankcase ventilation passages

DOEpatents

Boggs, David Lee; Baraszu, Daniel James; Foulkes, David Mark; Gomes, Enio Goyannes

1998-01-01

An internal combustion engine includes separated oil drain-back and crankcase ventilation passages. The oil drain-back passages extend from the cylinder head to a position below the top level of oil in the engine's crankcase. The crankcase ventilation passages extend from passages formed in the main bearing bulkheads from positions above the oil level in the crankcase and ultimately through the cylinder head. Oil dams surrounding the uppermost portions of the crankcase ventilation passages prevent oil from running downwardly through the crankcase ventilation passages.

Comparison of Engine Cycle Codes for Rocket-Based Combined Cycle Engines

NASA Technical Reports Server (NTRS)

Waltrup, Paul J.; Auslender, Aaron H.; Bradford, John E.; Carreiro, Louis R.; Gettinger, Christopher; Komar, D. R.; McDonald, J.; Snyder, Christopher A.

2002-01-01

This paper summarizes the results from a one day workshop on Rocket-Based Combined Cycle (RBCC) Engine Cycle Codes held in Monterey CA in November of 2000 at the 2000 JANNAF JPM with the authors as primary participants. The objectives of the workshop were to discuss and compare the merits of existing Rocket-Based Combined Cycle (RBCC) engine cycle codes being used by government and industry to predict RBCC engine performance and interpret experimental results. These merits included physical and chemical modeling, accuracy and user friendliness. The ultimate purpose of the workshop was to identify the best codes for analyzing RBCC engines and to document any potential shortcomings, not to demonstrate the merits or deficiencies of any particular engine design. Five cases representative of the operating regimes of typical RBCC engines were used as the basis of these comparisons. These included Mach 0 sea level static and Mach 1.0 and Mach 2.5 Air-Augmented-Rocket (AAR), Mach 4 subsonic combustion ramjet or dual-mode scramjet, and Mach 8 scramjet operating modes. Specification of a generic RBCC engine geometry and concomitant component operating efficiencies, bypass ratios, fuel/oxidizer/air equivalence ratios and flight dynamic pressures were provided. The engine included an air inlet, isolator duct, axial rocket motor/injector, axial wall fuel injectors, diverging combustor, and exit nozzle. Gaseous hydrogen was used as the fuel with the rocket portion of the system using a gaseous H2/O2 propellant system to avoid cryogenic issues. The results of the workshop, even after post-workshop adjudication of differences, were surprising. They showed that the codes predicted essentially the same performance at the Mach 0 and I conditions, but progressively diverged from a common value (for example, for fuel specific impulse, Isp) as the flight Mach number increased, with the largest differences at Mach 8. The example cases and results are compared and discussed in this paper.

Flow Split Venturi, Axially-Rotated Valve

DOEpatents

Walrath, David E.; Lindberg, William R.; Burgess, Robert K.; LaBelle, James

2000-02-22

The present invention provides an axially-rotated valve which permits increased flow rates and lower pressure drop (characterized by a lower loss coefficient) by using an axial eccentric split venturi with two portions where at least one portion is rotatable with respect to the other portion. The axially-rotated valve typically may be designed to avoid flow separation and/or cavitation at full flow under a variety of conditions. Similarly, the valve is designed, in some embodiments, to produce streamlined flow within the valve. An axially aligned outlet may also increase the flow efficiency. A typical cross section of the eccentric split venturi may be non-axisymmetric such as a semicircular cross section which may assist in both throttling capabilities and in maximum flow capacity using the design of the present invention. Such a design can include applications for freeze resistant axially-rotated valves and may be fully-opened and fully-closed in one-half of a complete rotation. An internal wide radius elbow typically connected to a rotatable portion of the eccentric venturi may assist in directing flow with lower friction losses. A valve actuator may actuate in an axial manner yet be uniquely located outside of the axial flow path to further reduce friction losses. A seal may be used between the two portions that may include a peripheral and diametrical seal in the same plane. A seal separator may increase the useful life of the seal between the fixed and rotatable portions.

Recuperator construction for a gas turbine engine

DOEpatents

Kang, Yungmo; McKeirnan, Jr., Robert D.

2006-12-12

A counter-flow recuperator formed from annular arrays of recuperator core segments. The recuperator core segments are formed from two opposing sheets of fin fold material coined to form a primary surface zone disposed between two flattened manifold zones. Each primary surface zone has undulating corrugations including a uniform, full height central portion and a transition zone disposed between the central portion and one of the manifold zones. Corrugations of the transition zone rise from zero adjacent to the manifold zone and increase along a transition length to full crest height at the central portion. The transition lengths increase in a direction away from an inner edge containing the air inlet so as to equalize air flow to the distal regions of the primary surface zone.

Ultra High Bypass Ratio Engine Research for Reducing Noise, Emissions, and Fuel Consumption

NASA Technical Reports Server (NTRS)

Hughes, Christopher E.; Schweitzer, Jeff

2007-01-01

A pictorial history of NASA development of advanced engine technologies for reducing environmental emissions and increasing performance from the 1970s to 2000s is presented. The goals of the Subsonic Fixed Wing Program portion of the NASA Fundamental Aeronautics Program are discussed, along with the areas of investigation currently being pursued by the Ultra High Bypass Partnership Element of the Subsonic Fixed Wing Program.

Reverse engineering of integrated circuits

DOEpatents

Chisholm, Gregory H.; Eckmann, Steven T.; Lain, Christopher M.; Veroff, Robert L.

2003-01-01

Software and a method therein to analyze circuits. The software comprises several tools, each of which perform particular functions in the Reverse Engineering process. The analyst, through a standard interface, directs each tool to the portion of the task to which it is most well suited, rendering previously intractable problems solvable. The tools are generally used iteratively to produce a successively more abstract picture of a circuit, about which incomplete a priori knowledge exists.

Split Venturi, Axially-Rotated Valve

DOEpatents

Walrath, David E.; Lindberg, William R.; Burgess, Robert K.

2000-08-29

The present invention provides an axially-rotated valve which permits increased flow rates and lower pressure drop (characterized by a lower loss coefficient) by using an axial eccentric split venturi with two portions where at least one portion is rotatable with respect to the other portion. The axially-rotated valve typically may be designed to avoid flow separation and/or cavitation at full flow under a variety of conditions. Similarly, the valve is designed, in some embodiments, to produce streamlined flow within the valve. A typical cross section of the eccentric split venturi may be non-axisymmetric such as a semicircular cross section which may assist in both throttling capabilities and in maximum flow capacity using the design of the present invention. Such a design can include applications for freeze resistant axially-rotated valves and may be fully-opened and fully-closed in one-half of a complete rotation. An internal wide radius elbow typically connected to a rotatable portion of the eccentric venturi may assist in directing flow with lower friction losses. A valve actuator may actuate in an axial manner yet be uniquely located outside of the axial flow path to further reduce friction losses. A seal may be used between the two portions that may include a peripheral and diametrical seal in the same plane.

Additive Manufacturing of Low Cost Upper Stage Propulsion Components

NASA Technical Reports Server (NTRS)

Protz, Christopher; Bowman, Randy; Cooper, Ken; Fikes, John; Taminger, Karen; Wright, Belinda

2014-01-01

NASA is currently developing Additive Manufacturing (AM) technologies and design tools aimed at reducing the costs and manufacturing time of regeneratively cooled rocket engine components. These Low Cost Upper Stage Propulsion (LCUSP) tasks are funded through NASA's Game Changing Development Program in the Space Technology Mission Directorate. The LCUSP project will develop a copper alloy additive manufacturing design process and develop and optimize the Electron Beam Freeform Fabrication (EBF3) manufacturing process to direct deposit a nickel alloy structural jacket and manifolds onto an SLM manufactured GRCop chamber and Ni-alloy nozzle. In order to develop these processes, the project will characterize both the microstructural and mechanical properties of the SLMproduced GRCop-84, and will explore and document novel design techniques specific to AM combustion devices components. These manufacturing technologies will be used to build a 25K-class regenerative chamber and nozzle (to be used with tested DMLS injectors) that will be tested individually and as a system in hot fire tests to demonstrate the applicability of the technologies. These tasks are expected to bring costs and manufacturing time down as spacecraft propulsion systems typically comprise more than 70% of the total vehicle cost and account for a significant portion of the development schedule. Additionally, high pressure/high temperature combustion chambers and nozzles must be regeneratively cooled to survive their operating environment, causing their design to be time consuming and costly to build. LCUSP presents an opportunity to develop and demonstrate a process that can infuse these technologies into industry, build competition, and drive down costs of future engines.

Engine Would Recover Exhaust Energy More Efficiently

NASA Technical Reports Server (NTRS)

Dimpelfeld, Philip M.

1993-01-01

Exhaust energy used for supercharging and extra shaft power. Flow of exhaust apportioned by waste gate to meet demand of turbocharger, and portion not fed to turbocharger sent to power-recovery turbine. Expected to increase fuel efficiency.

48 CFR 1852.228-70 - Aircraft ground and flight risk.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., vertical take-off aircraft, lighter-than-air airships, or other nonconventional types of aircraft, the... engine, wing, or a portion of a wing is attached to the fuselage) to be furnished to the Government under...

48 CFR 1852.228-70 - Aircraft ground and flight risk.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., vertical take-off aircraft, lighter-than-air airships, or other nonconventional types of aircraft, the... engine, wing, or a portion of a wing is attached to the fuselage) to be furnished to the Government under...

48 CFR 1852.228-70 - Aircraft ground and flight risk.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., vertical take-off aircraft, lighter-than-air airships, or other nonconventional types of aircraft, the... engine, wing, or a portion of a wing is attached to the fuselage) to be furnished to the Government under...

48 CFR 1852.228-70 - Aircraft ground and flight risk.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., vertical take-off aircraft, lighter-than-air airships, or other nonconventional types of aircraft, the... engine, wing, or a portion of a wing is attached to the fuselage) to be furnished to the Government under...

48 CFR 1852.228-70 - Aircraft ground and flight risk.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., vertical take-off aircraft, lighter-than-air airships, or other nonconventional types of aircraft, the... engine, wing, or a portion of a wing is attached to the fuselage) to be furnished to the Government under...

Boundary Layer Transition on X-43A

NASA Technical Reports Server (NTRS)

Berry, Scott; Daryabeigi, Kamran; Wurster, Kathryn; Bittner, Robert

2008-01-01

The successful Mach 7 and 10 flights of the first fully integrated scramjet propulsion systems by the Hyper-X (X-43A) program have provided the means with which to verify the original design methodologies and assumptions. As part of Hyper-X s propulsion-airframe integration, the forebody was designed to include a spanwise array of vortex generators to promote boundary layer transition ahead of the engine. Turbulence at the inlet is thought to provide the most reliable engine design and allows direct scaling of flight results to groundbased data. Pre-flight estimations of boundary layer transition, for both Mach 7 and 10 flight conditions, suggested that forebody boundary layer trips were required to ensure fully turbulent conditions upstream of the inlet. This paper presents the results of an analysis of the thermocouple measurements used to infer the dynamics of the transition process during the trajectories for both flights, on both the lower surface (to assess trip performance) and the upper surface (to assess natural transition). The approach used in the analysis of the thermocouple data is outlined, along with a discussion of the calculated local flow properties that correspond to the transition events as identified in the flight data. The present analysis has confirmed that the boundary layer trips performed as expected for both flights, providing turbulent flow ahead of the inlet during critical portions of the trajectory, while the upper surface was laminar as predicted by the pre-flight analysis.

Snubber assembly for turbine blades

DOEpatents

Marra, John J

2013-09-03

A snubber associated with a rotatable turbine blade in a turbine engine, the turbine blade including a pressure sidewall and a suction sidewall opposed from the pressure wall. The snubber assembly includes a first snubber structure associated with the pressure sidewall of the turbine blade, a second snubber structure associated with the suction sidewall of the turbine blade, and a support structure. The support structure extends through the blade and is rigidly coupled at a first end portion thereof to the first snubber structure and at a second end portion thereof to the second snubber structure. Centrifugal loads exerted by the first and second snubber structures caused by rotation thereof during operation of the engine are at least partially transferred to the support structure, such that centrifugal loads exerted on the pressure and suctions sidewalls of the turbine blade by the first and second snubber structures are reduced.

Cooled airfoil in a turbine engine

DOEpatents

Vitt, Paul H; Kemp, David A; Lee, Ching-Pang; Marra, John J

2015-04-21

An airfoil in a gas turbine engine includes an outer wall and an inner wall. The outer wall includes a leading edge, a trailing edge opposed from the leading edge in a chordal direction, a pressure side, and a suction side. The inner wall is coupled to the outer wall at a single chordal location and includes portions spaced from the pressure and suction sides of the outer wall so as to form first and second gaps between the inner wall and the respective pressure and suction sides. The inner wall defines a chamber therein and includes openings that provide fluid communication between the respective gaps and the chamber. The gaps receive cooling fluid that provides cooling to the outer wall as it flows through the gaps. The cooling fluid, after traversing at least substantial portions of the gaps, passes into the chamber through the openings in the inner wall.

Evaluation of an Outer Loop Retrofit Architecture for Intelligent Turbofan Engine Thrust Control

NASA Technical Reports Server (NTRS)

Litt, Jonathan S.; Sowers, T. Shane

2006-01-01

The thrust control capability of a retrofit architecture for intelligent turbofan engine control and diagnostics is evaluated. The focus of the study is on the portion of the hierarchical architecture that performs thrust estimation and outer loop thrust control. The inner loop controls fan speed so the outer loop automatically adjusts the engine's fan speed command to maintain thrust at the desired level, based on pilot input, even as the engine deteriorates with use. The thrust estimation accuracy is assessed under nominal and deteriorated conditions at multiple operating points, and the closed loop thrust control performance is studied, all in a complex real-time nonlinear turbofan engine simulation test bed. The estimation capability, thrust response, and robustness to uncertainty in the form of engine degradation are evaluated.

Deep Space 1 is prepared for transport to launch pad

NASA Technical Reports Server (NTRS)

1998-01-01

In the Defense Satellite Communications Systems Processing Facility (DPF), Cape Canaveral Air Station (CCAS), workers place an anti-static blanket over the lower portion of Deep Space 1, to protect the spacecraft during transport to the launch pad. The first flight in NASA's New Millennium Program, Deep Space 1 is designed to validate 12 new technologies for scientific space missions of the next century, including the engine. Propelled by the gas xenon, the engine is being flight-tested for future deep space and Earth-orbiting missions. Deceptively powerful, the ion drive emits only an eerie blue glow as ionized atoms of xenon are pushed out of the engine. While slow to pick up speed, over the long haul it can deliver 10 times as much thrust per pound of fuel as liquid or solid fuel rockets. Other onboard experiments include software that tracks celestial bodies so the spacecraft can make its own navigation decisions without the intervention of ground controllers. Deep Space 1 will complete most of its mission objectives within the first two months, but will also do a flyby of a near-Earth asteroid, 1992 KD, in July 1999. Deep Space 1 will be launched aboard a Boeing Delta 7326 rocket from Launch Pad 17A, CCAS.

KSC-98pc1317

NASA Image and Video Library

1998-10-10

KENNEDY SPACE CENTER, FLA. -- In the Defense Satellite Communications Systems Processing Facility (DPF), Cape Canaveral Air Station (CCAS), workers place an anti-static blanket over the lower portion of Deep Space 1, to protect the spacecraft during transport to the launch pad. The first flight in NASA's New Millennium Program, Deep Space 1 is designed to validate 12 new technologies for scientific space missions of the next century, including the engine. Propelled by the gas xenon, the engine is being flight-tested for future deep space and Earth-orbiting missions. Deceptively powerful, the ion drive emits only an eerie blue glow as ionized atoms of xenon are pushed out of the engine. While slow to pick up speed, over the long haul it can deliver 10 times as much thrust per pound of fuel as liquid or solid fuel rockets. Other onboard experiments include software that tracks celestial bodies so the spacecraft can make its own navigation decisions without the intervention of ground controllers. Deep Space 1 will complete most of its mission objectives within the first two months, but will also do a flyby of a near-Earth asteroid, 1992 KD, in July 1999. Deep Space 1 will be launched aboard a Boeing Delta 7326 rocket from Launch Pad 17A, CCAS

Brush seal numerical simulation: Concepts and advances

NASA Technical Reports Server (NTRS)

Braun, M. J.; Kudriavtsev, V. V.

1994-01-01

The development of the brush seal is considered to be most promising among the advanced type seals that are presently in use in the high speed turbomachinery. The brush is usually mounted on the stationary portions of the engine and has direct contact with the rotating element, in the process of limiting the 'unwanted' leakage flows between stages, or various engine cavities. This type of sealing technology is providing high (in comparison with conventional seals) pressure drops due mainly to the high packing density (around 100 bristles/sq mm), and brush compliance with the rotor motions. In the design of modern aerospace turbomachinery leakage flows between the stages must be minimal, thus contributing to the higher efficiency of the engine. Use of the brush seal instead of the labyrinth seal reduces the leakage flow by one order of magnitude. Brush seals also have been found to enhance dynamic performance, cost less, and are lighter than labyrinth seals. Even though industrial brush seals have been successfully developed through extensive experimentation, there is no comprehensive numerical methodology for the design or prediction of their performance. The existing analytical/numerical approaches are based on bulk flow models and do not allow the investigation of the effects of brush morphology (bristle arrangement), or brushes arrangement (number of brushes, spacing between them), on the pressure drops and flow leakage. An increase in the brush seal efficiency is clearly a complex problem that is closely related to the brush geometry and arrangement, and can be solved most likely only by means of a numerically distributed model.

40 CFR 81.339 - Pennsylvania.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., 329-332 X Census tracts 13-75, 143, 158-161, 178-189, 295-297, 322, 324, 327 X Balance of city X (B... Allen Township X (C) Reading Air Basin X (D) Carbon County X (E) Remaining Portions of AQCR X III. South...) Remaining Pennsylvania Portion of the AQCR X Pennsylvania—Carbon Monoxide Designated Area Designation Date 1...

40 CFR 81.339 - Pennsylvania.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., 329-332 X Census tracts 13-75, 143, 158-161, 178-189, 295-297, 322, 324, 327 X Balance of city X (B... Allen Township X (C) Reading Air Basin X (D) Carbon County X (E) Remaining Portions of AQCR X III. South...) Remaining Pennsylvania Portion of the AQCR X Pennsylvania—Carbon Monoxide Designated Area Designation Date 1...

40 CFR 81.339 - Pennsylvania.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., 329-332 X Census tracts 13-75, 143, 158-161, 178-189, 295-297, 322, 324, 327 X Balance of city X (B... Allen Township X (C) Reading Air Basin X (D) Carbon County X (E) Remaining Portions of AQCR X III. South...) Remaining Pennsylvania Portion of the AQCR X Pennsylvania—Carbon Monoxide Designated Area Designation Date 1...

The Contribution of Expanding Portion Sizes to the US Obesity Epidemic

PubMed Central

Young, Lisa R.; Nestle, Marion

2002-01-01

Objectives. Because larger food portions could be contributing to the increasing prevalence of overweight and obesity, this study was designed to weigh samples of marketplace foods, identify historical changes in the sizes of those foods, and compare current portions with federal standards. Methods. We obtained information about current portions from manufacturers or from direct weighing; we obtained information about past portions from manufacturers or contemporary publications. Results. Marketplace food portions have increased in size and now exceed federal standards. Portion sizes began to grow in the 1970s, rose sharply in the 1980s, and have continued in parallel with increasing body weights. Conclusions. Because energy content increases with portion size, educational and other public health efforts to address obesity should focus on the need for people to consume smaller portions. PMID:11818300

STS-85 Day 08 Highlights

NASA Technical Reports Server (NTRS)

1997-01-01

On this eighth day of the STS-85 mission, the flight crew, Cmdr. Curtis L. Brown, Jr., Pilot Kent V. Rominger, Payload Cmdr. N. Jan Davis (Ph.D.), Mission Specialists Robert L. Curbeam, Jr. and Stephen K. Robinson (Ph.D.), and Payload Specialist Bjarni V. Tryggvason entered the final portion of its flight. The new Mir 24 crew of Commander Anatoly Solovyev and Flight Engineer Pavel Vinogradov, who arrived on the station the same day Discovery was launched, bid farewell to Mir 23 Commander Vasily Tsibliev and Flight Engineer Alexander Lazutkin who are returning home after 185 days in space. The Soyuz vehicle carrying the Mir 23 crew home undocked from the station. Robinson again used the Southwest Ultraviolet Imaging System (SWUIS), a 7-inch imaging telescope that is pointed out of the orbiter's middeck hatch window, to observe the Hale-Bopp comet. Curbeam continued his work with the Bioreactor Demonstration System designed to perform cell biology experiments under controlled conditions. Tryggvason spent part of his time troubleshooting a computer hard drive system that supports the Microgravity Vibration Isolation Mount experiment.

Estimation of Missing Water-Level Data for the Everglades Depth Estimation Network (EDEN)

USGS Publications Warehouse

Conrads, Paul; Petkewich, Matthew D.

2009-01-01

The Everglades Depth Estimation Network (EDEN) is an integrated network of real-time water-level gaging stations, ground-elevation models, and water-surface elevation models designed to provide scientists, engineers, and water-resource managers with current (2000-2009) water-depth information for the entire freshwater portion of the greater Everglades. The U.S. Geological Survey Greater Everglades Priority Ecosystems Science provides support for EDEN and their goal of providing quality-assured monitoring data for the U.S. Army Corps of Engineers Comprehensive Everglades Restoration Plan. To increase the accuracy of the daily water-surface elevation model, water-level estimation equations were developed to fill missing data. To minimize the occurrences of no estimation of data due to missing data for an input station, a minimum of three linear regression equations were developed for each station using different input stations. Of the 726 water-level estimation equations developed to fill missing data at 239 stations, more than 60 percent of the equations have coefficients of determination greater than 0.90, and 92 percent have an coefficient of determination greater than 0.70.

Review of carbon dioxide research staffing and academic support

NASA Astrophysics Data System (ADS)

Clark, S. B.; Howard, L.; Stevenson, W.; Trice, J.

1985-04-01

More than 60 percent of the staff on Carbon Dioxide Research Division (CDRD) projects were university affiliated, and over one third of project scientists and engineers also had university teaching responsibilities. Almost 20 percent of project staff were students. CO2 research is unlikely to affect the general labor market for scientists and engineers because it uses such a small portion of the total pool. On the other hand, anticipated tight labor markets in some disciplines important to CO2 research may make it advantageous for CDRD to expand its support of university faculty, students, and staff to ensure that competent, knowledgeable researchers and managers are available for eventual policy decisions on CO2 issues. Options for academic support that lend themselves readily to the diffuse nature of CO2 research, while providing flexibility in the identification and accomplishment of specific programmatic objectives, include modifying procurement procedures for research contracts to enhance academic involvement, sponsoring summer institutes tailored to specific participants and focused on issues of interest to CDRD, and supporting traveling lecture programs designed to bring information of concern to CDRD to technical and nontechnical audiences.

Electrolyte management considerations in modern nickel/hydrogen and nickel/cadmium cell and battery designs

NASA Astrophysics Data System (ADS)

Thaller, Lawrence H.; Zimmerman, Albert H.

In the early 1980s, the battery group at the NASA Lewis Research Center (LeRC) reviewed the design issues associated with nickel/hydrogen cells for low-earth orbit applications. In 1984, these issues included gas management, liquid management, plate expansion, and the recombination of oxygen during overcharge. The design effort by that group followed principles set forth in an earlier LeRC paper that introduced the topic of pore size engineering. Also in 1984, the beneficial effect of lower electrolyte concentrations on cycle life was verified by Hughes Aircraft as part of a LeRC-funded study. Subsequent life cycle tests of these concepts have been carried out that essentially have verified all of this earlier work. During the past decade, some of the mysteries involved in the active material of the nickel electrode have been resolved by careful research done at several laboratories. While attention has been paid to understanding and modeling abnormal nickel/hydrogen cell behaviors, not enough attention has been paid to the potassium ion content in these cells, and more recently, in batteries. Examining the potassium ion content of different portions of the cell or battery is a convenient way of following the conductivity, mass transport properties, and electrolyte volume in each of the cell or battery portions under consideration. Several of the consequences of solvent and solute changes within fuel cells have been well known for some time. However, only recently have these consequences been applied to nickel/hydrogen and nickel/cadmium cell designs. As a result of these studies, several unusual cell performance signatures can now be satisfactorily explained in terms of movement of the solvent and solute components in the electrolyte. This paper will review three general areas where the potassium ion content can impact the performance and life of nickel/hydrogen and nickel/cadmium cells. Sample calculations of the concentration or volume changes that can take place within operating cells will be presented. With the aid of an accurate model of an operating cell or battery, the impact of changes of potassium ion content within a potential cell design can be estimated. All three of these areas are directly related to the volume tolerance and pore size engineering aspects of the components used in the cell or battery design. The three areas follow. (i) The gamma phase uptake of potassium ion can result in a lowering of the electrolyte concentration. This leads to a higher electrolyte resistance as well as electrolyte diffusional limitations on the discharge rate. This phenomenon also impacts the response of the cell to a reconditioning cycle. (ii) The transport of water vapor from a warmer to a cooler portion of the cell or battery under the driving force of a vapor pressure gradient has already impacted cells when water vapor condenses on a colder cell wall. This paper will explore the convective and diffusive movement of gases saturated with water vapor from a warmer plate pack to a cooler one, both with and without liquid communication. (iii) The impact of low-level shunt currents in multicell configurations results in the net movement of potassium hydroxide from one part of the battery to another. This movement impacts the electrolyte volume/vapor pressure relationships within the cell or battery.

Zachary-Fort Lauderdale pipeline construction and conversion project: final supplement to final environmental impact statement. Docket No. CP74-192

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This Final Supplement to the Final Environmental Impact Statement (Final Supplement) evaluates the economic, engineering, and environmental aspects of newly developed alternatives to an abandonment/conversion project proposed by Florida Gas Transmission Company (Florida Gas). It also updates the staff's previous FEIS and studies revisions to the original proposal. Wherever possible, the staff has adopted portions of its previous FEIS in lieu of reprinting portions of that analysis which require no change. 60 references, 8 figures, 35 tables.

Enhanced Eradication of Lymphoma by Tumor-Specific Cytotoxic T Cells Secreting and Engineered Tumor-Specific Immunotoxin

DTIC Science & Technology

2009-06-01

target delivery of an immunotoxin, the CD22 -Pseudomonas exotoxin A ( CD22 -PEA), which has already been used in a clinical setting . The toxin portion...contains the transloc ating and ADP-ribosylat ing dom ains of PEA, and the native cell-binding portion is replaced with a CD22 scFv that directs...targeting to B lymphocytes. CD22 -PEA was tested in a Phase I trial in B-cell malignancies, but tumor responses, particularly in hairy cell leukemia

Turbofan gas turbine engine with variable fan outlet guide vanes

NASA Technical Reports Server (NTRS)

Wood, Peter John (Inventor); LaChapelle, Donald George (Inventor); Grant, Carl (Inventor); Zenon, Ruby Lasandra (Inventor); Mielke, Mark Joseph (Inventor)

2010-01-01

A turbofan gas turbine engine includes a forward fan section with a row of fan rotor blades, a core engine, and a fan bypass duct downstream of the forward fan section and radially outwardly of the core engine. The forward fan section has only a single stage of variable fan guide vanes which are variable fan outlet guide vanes downstream of the forward fan rotor blades. An exemplary embodiment of the engine includes an afterburner downstream of the fan bypass duct between the core engine and an exhaust nozzle. The variable fan outlet guide vanes are operable to pivot from a nominal OGV position at take-off to an open OGV position at a high flight Mach Number which may be in a range of between about 2.5-4+. Struts extend radially across a radially inwardly curved portion of a flowpath of the engine between the forward fan section and the core engine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chiaro, PJ

The Environmental Effects Laboratory of the Engineering Science and Technology Division of Oak Ridge National Laboratory performed a series of tests to further evaluate and characterize the radiological response of a ''Cricket'' radiation detection system. The Cricket, manufactured by Rad/Comm Systems Corporation of Ontario, Canada, is designed to detect radioactive material that may be contained in scrap metal. The Cricket's detection unit is designed to be mounted to the base of a grappler, allowing it to monitor material while the material is being held by the grappler tines. The Cricket was tested for background stability, energy response, spherical response, surfacemore » uniformity, angular dependence, and alarm actuation. Some of these tests were repeated from a prior test of a Cricket at the Environmental Effects Laboratory as reported in ORNL/TM-2002/94. Routine environmental tests--normal temperature and relatively humidity--were also performed as part of this testing process. Overall, the Cricket performed well during the testing process. The design of the instrument and the inherent photon energy of the radionuclides had some affect on portions of the tests but do not detract from the value-added benefits of the Cricket's detection capabilities.« less

Virtual Observer Controller (VOC) for Small Unit Infantry Laser Simulation Training

DTIC Science & Technology

2007-04-01

per-seat license when deployed. As a result, ViaVoice was abandoned early in development. Next, the SPHINX engine from Carnegie Mellon University was...examined. Sphinx is Java-based software, providing cross-platform functionality, and it is also free, open-source software. Software developers at...IST had experience using SPHINX , so it was initially selected it to be the VOC speech engine. After implementing a small portion of the VOC grammar

Safety evaluation of the SCATS control system, final report.

DOT National Transportation Integrated Search

2010-09-01

Since 1992, traffic signals in Oakland County and a portion of Macomb and Wayne Counties of Michigan have been : converted to the Sydney Coordinated Adaptive Traffic System (SCATS). County traffic engineers have been : adjusting various SCATS paramet...

Williams in Node 1 / Unity module

NASA Image and Video Library

2007-03-01

ISS014-E-15830 (4 March 2007) --- Astronaut Sunita L. Williams, Expedition 14 flight engineer, works with a portion of the Treadmill Vibration Isolation System (TVIS) during in-flight maintenance (IFM) in the Unity node of the International Space Station.

Internal-integral sodium return line for sodium heat engine

DOEpatents

Hunt, Thomas K.

1985-01-01

A thermoelectric generator device which converts heat energy to electrical energy. An alkali metal is used with a solid electrolyte and a portion of the return line for the alkali metal is located within the generator vacuum space.

Requirements Analysis Study for Master Pump Shutdown System Project Development Specification [SEC 1 and 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

BEVINS, R.R.

This study is a requirements document that presents analysis for the functional description for the master pump shutdown system. This document identifies the sources of the requirements and/or how these were derived. Each requirement is validated either by quoting the source or an analysis process involving the required functionality, performance characteristics, operations input or engineering judgment. The requirements in this study apply to the first phase of the W314 Project. This document has been updated during the definitive design portion of the first phase of the W314 Project to capture additional software requirements and is planned to be updated duringmore » the second phase of the W314 Project to cover the second phase of the project's scope.« less

Aerodynamic characteristics of a fixed arrow-wing supersonic cruise aircraft at Mach numbers of 2.30, 2.70, and 2.95. [Langley Unitary Plan wind tunnel tests

NASA Technical Reports Server (NTRS)

Morris, O. A.; Fuller, D. E.; Watson, C. B.

1978-01-01

Tests were conducted in the Langley Unitary Plan wind tunnel at Mach numbers of 2.30. 2.70, and 2.95 to determine the performance, static stability, and control characteristics of a model of a fixed-wing supersonic cruise aircraft with a design Mach Number of 2.70 (SCAT 15-F-9898). The configuration had a 74 deg swept warped wing with a reflexed trailing edge and four engine nacelles mounted below the reflexed portion of the wing. A number of variations in the basic configuration were investigated; they included the effect of wing leading edge radius, the effect of various model components, and the effect of model control deflections.

A Horizontal Take-off and Landing satellite launcher or aerospace plane (HOTOL)

NASA Astrophysics Data System (ADS)

Conchie, P. J.

1985-09-01

An assessment is made of the technology readiness and typical mission profile of a Horizontal Takeoof and Landing (HOTOL) single-stage satellite launch vehicle for 1990s deployment. HOTOL would employ H2-fueled air-breathing propulsion for the first stage of its ascent to low earth orbit through the lower portions of the atmosphere; it would then switch to H2-fueled rocket engines using liquid oxygen from internal tanks for exoatmospheric flight and orbit insertion. Mission cost comparisons are made with alternative launch vehicle design options. HOTOL is approximately the same size as the Concorde SST, and will weigh so much less than the current Space Shuttle as to significantly reduce reentry speeds and temperatures, obviating ceramic insulation systems for the primary structure.

Space processing applications rocket project. SPAR 8

NASA Technical Reports Server (NTRS)

Chassay, R. P. (Editor)

1984-01-01

The Space Processing Applications Rocket Project (SPAR) VIII Final Report contains the engineering report prepared at the Marshall Space Flight Center (MSFC) as well as the three reports from the principal investigators. These reports also describe pertinent portions of ground-based research leading to the ultimate selection of the flight sample composition, including design, fabrication, and testing, all of which are expected to contribute immeasurably to an improved comprehension of materials processing in space. This technical memorandum is directed entirely to the payload manifest flown in the eighth of a series of SPAR flights conducted at the White Sands Missile Range (WSMR) and includes the experiments entitled Glass Formation Experiment SPAR 74-42/1R, Glass Fining Experiment in Low-Gravity SPAR 77-13/1, and Dynamics of Liquid Bubbles SPAR Experiment 77-18/2.

Turbine exhaust diffuser with region of reduced flow area and outer boundary gas flow

DOEpatents

Orosa, John

2014-03-11

An exhaust diffuser system and method for a turbine engine. The outer boundary may include a region in which the outer boundary extends radially inwardly toward the hub structure and may direct at least a portion of an exhaust flow in the diffuser toward the hub structure. At least one gas jet is provided including a jet exit located on the outer boundary. The jet exit may discharge a flow of gas downstream substantially parallel to an inner surface of the outer boundary to direct a portion of the exhaust flow in the diffuser toward the outer boundary to effect a radially outward flow of at least a portion of the exhaust gas flow toward the outer boundary to balance an aerodynamic load between the outer and inner boundaries.

Gas turbine nozzle vane insert and methods of installation

DOEpatents

Miller, William John; Predmore, Daniel Ross; Placko, James Michael

2002-01-01

A pair of hollow elongated insert bodies are disposed in one or more of the nozzle vane cavities of a nozzle stage of a gas turbine. Each insert body has an outer wall portion with apertures for impingement-cooling of nozzle wall portions in registration with the outer wall portion. The insert bodies are installed into the cavity separately and spreaders flex the bodies toward and to engage standoffs against wall portions of the nozzle whereby the designed impingement gap between the outer wall portions of the insert bodies and the nozzle wall portions is achieved. The spreaders are secured to the inner wall portions of the insert bodies and the bodies are secured to one another and to the nozzle vane by welding or brazing.

How food marketers can sell smaller portions: Consumer insights and product innovation.

PubMed

Riis, J; Fisher, J O; Rowe, S

2016-08-01

Food portion size has been shown to be an important driver of energy intake. Despite the well acknowledged role of portion control in weight management, large portion sizes remain ubiquitous in the marketplace. Moving consumers towards consumption of smaller portion sizes will require changes in consumer behavior as well as changes in products available to consumers in a variety of settings. This special supplement presents cutting edge research aimed at understanding consumer behavior around portion size and innovations in product design that may promote the selection and consumption of smaller portion sizes. We identify further research that will be needed to translate basic behavioral findings into real world settings and to viable product development. Copyright © 2016. Published by Elsevier Ltd.

Humanizing Instructional Videos in Physics: When Less Is More

NASA Astrophysics Data System (ADS)

Schroeder, Noah L.; Traxler, Adrienne L.

2017-06-01

Many instructors in science, technology, engineering, and mathematics fields are striving to create active learning environments in their classrooms and in doing so are frequently moving the lecture portion of their course into online video format. In this classroom-based study, we used a two group randomized experimental design to examine the efficacy of an instructional video that incorporates a human hand demonstrating and modeling how to solve frictional inclined plane problems compared to an identical video that did not include the human hand. The results show that the learners who viewed the video without the human hand present performed significantly better on a learning test and experienced a significantly better training efficiency than the learners who viewed the video with the human hand present. Meanwhile, those who learned with the human hand present in the instructional video rated the instructor as being more humanlike and engaging. The results have implications for both theory and practice. Implications for those designing instructional videos are discussed, as well as the limitations of the current study.

Process of videotape making: presentation design, software, and hardware

NASA Astrophysics Data System (ADS)

Dickinson, Robert R.; Brady, Dan R.; Bennison, Tim; Burns, Thomas; Pines, Sheldon

1991-06-01

The use of technical video tape presentations for communicating abstractions of complex data is now becoming commonplace. While the use of video tapes in the day-to-day work of scientists and engineers is still in its infancy, their use as applications oriented conferences is now growing rapidly. Despite these advancements, there is still very little that is written down about the process of making technical videotapes. For printed media, different presentation styles are well known for categories such as results reports, executive summary reports, and technical papers and articles. In this paper, the authors present ideas on the topic of technical videotape presentation design in a format that is worth referring to. They have started to document the ways in which the experience of media specialist, teaching professionals, and character animators can be applied to scientific animation. Software and hardware considerations are also discussed. For this portion, distinctions are drawn between the software and hardware required for computer animation (frame at a time) productions, and live recorded interaction with a computer graphics display.

The application of exergy to human-designed systems

NASA Astrophysics Data System (ADS)

Hamilton, P.

2012-12-01

Exergy is the portion of the total energy of a system that is available for conversion to useful work. Exergy takes into account both the quantity and quality of energy. Heat is the inevitable product of using any form of high-quality energy such as electricity. Modern commercial buildings and industrial facilities use large amounts of electricity and so produce huge amounts of heat. This heat energy typically is treated as a waste product and discharged to the environment and then high-quality energy sources are consumed to satisfy low-quality energy heating and cooling needs. Tens of thousands of buildings and even whole communities could meet much of their heating and cooling needs through the capture and reuse of heat energy. Yet the application of exergy principles often faces resistance because it challenges conventions about how we design, construct and operate human-engineered systems. This session will review several exergy case studies and conclude with an audience discussion of how exergy principles may be both applied and highlighted in formal and informal education settings.

Distributed ESO based cooperative tracking control for high-order nonlinear multiagent systems with lumped disturbance and application in multi flight simulators systems.

PubMed

Cong, Zhang

2018-03-01

Based on extended state observer, a novel and practical design method is developed to solve the distributed cooperative tracking problem of higher-order nonlinear multiagent systems with lumped disturbance in a fixed communication topology directed graph. The proposed method is designed to guarantee all the follower nodes ultimately and uniformly converge to the leader node with bounded residual errors. The leader node, modeled as a higher-order non-autonomous nonlinear system, acts as a command generator giving commands only to a small portion of the networked follower nodes. Extended state observer is used to estimate the local states and lumped disturbance of each follower node. Moreover, each distributed controller can work independently only requiring the relative states and/or the estimated relative states information between itself and its neighbors. Finally an engineering application of multi flight simulators systems is demonstrated to test and verify the effectiveness of the proposed algorithm. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Viking 1975 Orbiter Development Test Model/Lander Dynamic Test Model dynamic environmental testing - An overview

NASA Technical Reports Server (NTRS)

Milder, G.

1975-01-01

The current work presents an overview of the Viking 1975 environmental testing from an engineering standpoint. An extremely large vibration test fixture had to be designed, analyzed, and integrated into a test setup that employed hydrostatic bearings in a new fashion. A vibration control system was also required that would allow for thirty-six channels of sine-wave peak select control from acceleration, force-of-strain transducers. In addition, some 68 channels of peak limiting shutdown capability were needed for backup and monitoring of other data during the forced vibration test. Pretesting included analyses of the fixture design, overturning moment, control system capabilities, and response of the entire spacecraft/fixture/exciter system to the test environment. Closed-loop control for acoustic testing was a necessity due to the fact that the Viking spacecraft took up a major portion of the volume of the 10,000 cu ft chamber. The spacecraft emerged from testing undamaged.

Design Optimization of a Variable-Speed Power Turbine

NASA Technical Reports Server (NTRS)

Hendricks, Eric S.; Jones, Scott M.; Gray, Justin S.

2014-01-01

NASA's Rotary Wing Project is investigating technologies that will enable the development of revolutionary civil tilt rotor aircraft. Previous studies have shown that for large tilt rotor aircraft to be viable, the rotor speeds need to be slowed significantly during the cruise portion of the flight. This requirement to slow the rotors during cruise presents an interesting challenge to the propulsion system designer as efficient engine performance must be achieved at two drastically different operating conditions. One potential solution to this challenge is to use a transmission with multiple gear ratios and shift to the appropriate ratio during flight. This solution will require a large transmission that is likely to be maintenance intensive and will require a complex shifting procedure to maintain power to the rotors at all times. An alternative solution is to use a fixed gear ratio transmission and require the power turbine to operate efficiently over the entire speed range. This concept is referred to as a variable-speed power-turbine (VSPT) and is the focus of the current study. This paper explores the design of a variable speed power turbine for civil tilt rotor applications using design optimization techniques applied to NASA's new meanline tool, the Object-Oriented Turbomachinery Analysis Code (OTAC).

18 CFR 367.1760 - Account 176, Derivative instrument assets-Hedges.

Code of Federal Regulations, 2014 CFR

2014-04-01

... change in the fair value of derivative instrument assets designated by the service company as cash flow or fair value hedges. (b) When a service company designates a derivative instrument asset as a cash... effective portion of the gain or loss. The ineffective portion of the cash flow hedge must be charged to the...

18 CFR 367.1760 - Account 176, Derivative instrument assets-Hedges.

Code of Federal Regulations, 2011 CFR

2011-04-01

... change in the fair value of derivative instrument assets designated by the service company as cash flow or fair value hedges. (b) When a service company designates a derivative instrument asset as a cash... effective portion of the gain or loss. The ineffective portion of the cash flow hedge must be charged to the...

18 CFR 367.1760 - Account 176, Derivative instrument assets-Hedges.

Code of Federal Regulations, 2013 CFR

2013-04-01

... change in the fair value of derivative instrument assets designated by the service company as cash flow or fair value hedges. (b) When a service company designates a derivative instrument asset as a cash... effective portion of the gain or loss. The ineffective portion of the cash flow hedge must be charged to the...

18 CFR 367.1760 - Account 176, Derivative instrument assets-Hedges.

Code of Federal Regulations, 2012 CFR

2012-04-01

... change in the fair value of derivative instrument assets designated by the service company as cash flow or fair value hedges. (b) When a service company designates a derivative instrument asset as a cash... effective portion of the gain or loss. The ineffective portion of the cash flow hedge must be charged to the...

18 CFR 367.1760 - Account 176, Derivative instrument assets-Hedges.

Code of Federal Regulations, 2010 CFR

2010-04-01

... change in the fair value of derivative instrument assets designated by the service company as cash flow or fair value hedges. (b) When a service company designates a derivative instrument asset as a cash... effective portion of the gain or loss. The ineffective portion of the cash flow hedge must be charged to the...

NUCLEAR REACTOR FUEL ELEMENT

DOEpatents

Currier, E.L. Jr.; Nicklas, J.H.

1963-06-11

A fuel plate is designed for incorporation into control rods of the type utilized in high-flux test reactors. The fuel plate is designed so that the portion nearest the poison section of the control rod contains about one-half as much fissionable material as in the rest of the plate, thereby eliminating dangerous flux peaking in that portion. (AEC)

The Tracer Gas Method of Determining the Charging Efficiency of Two-stroke-cycle Diesel Engines

NASA Technical Reports Server (NTRS)

Schweitzer, P H; Deluca, Frank, Jr

1942-01-01

A convenient method has been developed for determining the scavenging efficiency or the charging efficiency of two-stroke-cycle engines. The method consists of introducing a suitable tracer gas into the inlet air of the running engine and measuring chemically its concentration both in the inlet and exhaust gas. Monomethylamine CH(sub 3)NH(sub 2) was found suitable for the purpose as it burns almost completely during combustion, whereas the "short-circuited" portion does not burn at all and can be determined quantitatively in the exhaust. The method was tested both on four-stroke and on two-stroke engines and is considered accurate within 1 percent.

Flow-induced oscillations of a floating moored cylinder

NASA Astrophysics Data System (ADS)

Carlson, Daniel; Modarres-Sadeghi, Yahya

2016-11-01

An experimental study of flow-induced oscillations of a floating model spar buoy was conducted. The model spar consisted of a floating uniform cylinder moored in a water tunnel test section, and free to oscillate about its mooring attachment point near the center of mass. For the bare cylinder, counter-clockwise (CCW) figure-eight trajectories approaching A* =1 in amplitude were observed at the lower part of the spar for a reduced velocity range of U* =4-11, while its upper part experienced clockwise (CW) orbits. It was hypothesized that the portion of the spar undergoing CCW figure eights is the portion within which the flow excites the structure. By adding helical strakes to the portion of the cylinder with CCW figure eights, the response amplitude was significantly reduced, while adding strakes to portions with clockwise orbital motion had a minimal influence on the amplitude of response. This work is partially supported by the NSF-sponsored IGERT: Offshore Wind Energy Engineering, Environmental Science, and Policy (Grant Number 1068864).

Performance and Operational Characteristics of a Python Turbine-propeller Engine at Simulated Altitude Conditions / Carl L. Meyer and Lavern A. Johnson

NASA Technical Reports Server (NTRS)

Meyer, Carl L; Johnson, Lavern A

1952-01-01

The performance and operational characteristics of a Python turbine-propeller engine were investigated at simulated altitude conditions in the NACA Lewis altitude wind tunnel. In the performance phase, data were obtained over a range of engine speeds and exhaust nozzle areas at altitudes from 10,000 to 40,000 feet at a single cowl-inlet ram pressure ratio; independent control of engine speed and fuel flow was used to obtain a range of powers at each engine speed. Engine performance data obtained at a given altitude could not be used to predict performance accurately at other altitudes by use of the standard air pressure and temperature generalizing factors. At a given engine speed and turbine-inlet total temperature, a greater portion of the total available energy was converted to propulsive power as the altitude increased.

76 FR 20291 - Approval and Promulgation of Implementation Plans and Designations of Areas for Air Quality...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-12

... their entireties, and a portion of Walker County in Alabama. This proposed determination of attaining... Birmingham Area (comprised of Jefferson and Shelby Counties in their entireties, and a portion of Walker... Jefferson and Shelby Counties in their entireties, and a portion of Walker County in Alabama. Under EPA...

Structureborne noise investigations of a twin engine aircraft

NASA Technical Reports Server (NTRS)

Garrelick, J. M.; Cole, J. E., III; Martini, K.

1986-01-01

The interior noise of aircraft powered by advanced turbo-prop concepts is likely to have nonnegligible contributions from structureborne paths, these paths being those involving propeller loads transmitted to the structures of the lifting surfaces. As a means of examining these paths, structural measurements have been performed on a small twin-engine aircraft, and in addition analytical models of the structure have been developed. In this paper results from both portions of this study are presented.

Second Generation RLV Space Vehicle Concept

NASA Astrophysics Data System (ADS)

Bailey, M. D.; Daniel, C. C.

2002-01-01

NASA has a long history of conducting development programs and projects in a consistant fashion. Systems Engineering within those programs and projects has also followed a given method outlined by such documents as the NASA Systems Engineering Handbook. The relatively new NASA Space Launch Initiative (SLI) is taking a new approach to developing a space vehicle, with innovative management methods as well as new Systems Engineering processes. With the program less than a year into its life cycle, the efficacy of these new processes has yet to be proven or disproven. At 776M for phase I, SLI represents a major portion of the NASA focus; however, the new processes being incorporated are not reflected in the training provided by NASA to its engineers. The NASA Academy of Program and Project Leadership (APPL) offers core classes in program and project management and systems engineering to NASA employees with the purpose of creating a "knowledge community where ideas, skills, and experiences are exchanged to increase each other's capacity for strong leadership". The SLI program is, in one sense, a combination of a conceptual design program and a technology program. The program as a whole doesn't map into the generic systems engineering project cycle as currently, and for some time, taught. For example, the NASA APPL Systems Engineering training course teaches that the "first step in developing an architecture is to define the external boundaries of the system", which will require definition of the interfaces with other systems and the next step will be to "define all the components that make up the next lower level of the system hierarchy" where fundamental requirements are allocated to each component. Whereas, the SLI technology risk reduction approach develops architecture subsystem technologies prior to developing architectures. The higher level architecture requirements are not allowed to fully develop and undergo decomposition and allocation down to the subsystems before the subsystems must develop allocated requirements based on the highest level of requirements. In the vernacular of the project cycles prior to the mid 1990's, the architecture definition portion of the program appears to be at a generic Phase A stage, while the subsystems are operating at Phase B. Even the management structure of the SLI program is innovative in its approach to Systems Engineering and is not reflected in the APPL training modules. The SLI program has established a Systems Engineering office as an office separate from the architecture development or the subsystem technology development, while that office does have representatives within these other offices. The distributed resources of the Systems Engineering Office are co=located with the respect Project Offices. This template is intended to provide systems engineering as an integrated function at the Program Level. . Undoubtedly, the program management of SLI and the NIAT agree that "program/project managers and the systems engineering team must work closely together towards the single objective of delivering quality products that meet the customer needs". This paper will explore the differences between the methods being taught by NASA, which represent decades of ideas, and those currently in practice in SLI. Time will tell if the innovation employed by SLI will prove to be the model of the future. For now, it is suggested that the training of the present exercise the flexibility of recognizing the new processes employed by a major new NASA program.

Second Generation RLV Space Vehicle Concept

NASA Technical Reports Server (NTRS)

Bailey, Michelle; Daniel, Charles; Throckmorton, David A. (Technical Monitor)

2002-01-01

NASA has a long history of conducting development programs and projects in a consistent fashion. Systems Engineering within those programs and projects has also followed a given method outlined by such documents as the NASA Systems Engineering Handbook. The relatively new NASA Space Launch Initiative (SLI) is taking a new approach to developing a space vehicle, with innovative management methods as well as new Systems Engineering processes. With the program less than a year into its life cycle, the efficacy of these new processes has yet to be proven or disproven. At $776M for phase 1, SLI represents a major portion of the NASA focus; however, the new processes being incorporated are not reflected in the training provided by NASA to its engineers. The NASA Academy of Program and Project Leadership (APPL) offers core classes in program and project management and systems engineering to NASA employees with the purpose of creating a "knowledge community where ideas, skills, and experiences are exchanged to increase each other's capacity for strong leadership". The SLI program is, in one sense, a combination of a conceptual design program and a technology program. The program as a whole doesn't map into the generic systems engineering project cycle as currently, and for some time, taught. For example, the NASA APPL Systems Engineering training course teaches that the "first step in developing an architecture is to define the external boundaries of the system", which will require definition of the interfaces with other systems and the next step will be to "define all the components that make up the next lower level of the system hierarchy" where fundamental requirements are allocated to each component. Whereas, the SLI technology risk reduction approach develops architecture subsystem technologies prior to developing architectures. The higher level architecture requirements are not allowed to fully develop and undergo decomposition and allocation down to the subsystems before the subsystems must develop allocated requirements based on the highest level of requirements. In the vernacular of the project cycles prior to the mid 1990's, the architecture definition portion of the program appears to be at a generic Phase A stage, while the subsystems are operating at Phase B. Even the management structure of the SLI program is innovative in its approach to Systems Engineering and is not reflected in the APPL training modules. The SLI program has established a Systems Engineering office as an office separate from the architecture development or the subsystem technology development, while that office does have representatives within these other offices. The distributed resources of the Systems Engineering Office are co-located with the respective Project Offices. This template is intended to provide systems engineering as an integrated function at the Program Level. the program management of SLI and the MAT agree that "program/project managers and the systems engineering team must work closely together towards the single objective of delivering quality products that meet the customer needs". This paper will explore the differences between the methods being taught by NASA, which represent decades of ideas, and those currently in practice in SLI. Time will tell if the innovation employed by SLI will prove to be the model of the future. For now, it is suggested that the training of the present exercise the flexibility of recognizing the new processes employed by a major new NASA program.

The second generation intelligent user interface for the crustal dynamics data information system. [for nasa space missions

NASA Technical Reports Server (NTRS)

Short, Nicholas, Jr.; Wattawa, Scott L.

1988-01-01

For the past decade, operations and research projects that support a major portion of NASA's overall mission have experienced a dramatic increase in the volume of generated data and resultant information that is unparalleled in the history of the agency. The effect of such an increase is that most of the science and engineering disciplines are undergoing an information glut, which has occurred, not only because of the amount, but also because of the type of data being collected. This information glut is growing exponentially and is expected to grow for the foreseeable future. Consequently, it is becoming physically and intellectually impossible to identify, access, modify, and analyze the most suitable information. Thus, the dilemma arises that the amount and complexity of information has exceeded and will continue to exceed, using present information systems, the ability of all the scientists and engineers to understand and take advantage of this information. As a result of this information problem, NASA has initiated the Intelligent Data Management (IDM) project to design and develop Advanced Information Management (IDM) project to design and develop Advanced Information Management Systems (AIMS). The first effort of the Project was the prototyping of an Intelligent User Interface (IUI) to an operational scientific database using expert systems, natural language processing, and graphics technologies. An overview of the IUI formulation and development for the second phase is presented.

Analysis of the design and economics of molten carbonate fuel cell tri-generation systems providing heat and power for commercial buildings and H2 for FC vehicles

NASA Astrophysics Data System (ADS)

Li, Xuping; Ogden, Joan; Yang, Christopher

2013-11-01

This study models the operation of molten carbonate fuel cell (MCFC) tri-generation systems for “big box” store businesses that combine grocery and retail business, and sometimes gasoline retail. Efficiency accounting methods and parameters for MCFC tri-generation systems have been developed. Interdisciplinary analysis and an engineering/economic model were applied for evaluating the technical, economic, and environmental performance of distributed MCFC tri-generation systems, and for exploring the optimal system design. Model results show that tri-generation is economically competitive with the conventional system, in which the stores purchase grid electricity and NG for heat, and sell gasoline fuel. The results are robust based on sensitivity analysis considering the uncertainty in energy prices and capital cost. Varying system sizes with base case engineering inputs, energy prices, and cost assumptions, it is found that there is a clear tradeoff between the portion of electricity demand covered and the capital cost increase of bigger system size. MCFC Tri-generation technology provides lower emission electricity, heat, and H2 fuel. With NG as feedstock the CO2 emission can be reduced by 10%-43.6%, depending on how the grid electricity is generated. With renewable methane as feedstock CO2 emission can be further reduced to near zero.

A simulator-based analysis of engineering treatments for right-hook bicycle crashes at signalized intersections.

PubMed

Warner, Jennifer; Hurwitz, David S; Monsere, Christopher M; Fleskes, Kayla

2017-07-01

A right-hook crash is a crash between a right-turning motor vehicle and an adjacent through-moving bicycle. At signalized intersections, these crashes can occur during any portion of the green interval when conflicting bicycles and vehicles are moving concurrently. The objective of this research was to evaluate the effectiveness of four types of engineering countermeasures - regulatory signage, intersection pavement marking, smaller curb radius, and protected intersection design - at modifying driver behaviors that are known contributing factors in these crashes. This research focused on right-hook crashes that occur during the latter stage of the circular green indication at signalized intersections with a shared right-turn and through lane. Changes in driver performance in response to treatments were measured in a high-fidelity driving simulator. Twenty-eight participants each completed 22 right-turn maneuvers. A partially counterbalanced experimental design exposed drivers to critical scenarios, which had been determined in a previous experiment. For each turn, driver performance measures, including visual attention, crash avoidance, and potential crash severity, were collected. A total of 75 incidents (47 near-collisions and 28 collisions) were observed during the 616 right turns. All treatments had some positive effect on measured driver performance with respect to the right-turn vehicle conflicts. Further work is required to map the magnitude of these changes in driver performance to crash-based outcomes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Overview of the Conceptual Design of the Future VENUS Neutron Imaging Beam Line at the Spallation Neutron Source

NASA Astrophysics Data System (ADS)

Bilheux, Hassina; Herwig, Ken; Keener, Scott; Davis, Larry

VENUS (Versatile Neutron Imaging Beam line at the Spallation Neutron Source) will be a world-class neutron-imaging instrument that will uniquely utilize the Spallation Neutron Source (SNS) time-of-flight (TOF) capabilities to measure and characterize objects across several length scales (mm to μm). When completed, VENUS will provide academia, industry and government laboratories with the opportunity to advance scientific research in areas such as energy, materials, additive manufacturing, geosciences, transportation, engineering, plant physiology, biology, etc. It is anticipated that a good portion of the VENUS user community will have a strong engineering/industrial research focus. Installed at Beam line 10 (BL10), VENUS will be a 25-m neutron imaging facility with the capability to fully illuminate (i.e., umbra illumination) a 20 cm x 20 cm detector area. The design allows for a 28 cm x 28 cm field of view when using the penumbra to 80% of the full illumination flux. A sample position at 20 m will be implemented for magnification measurements. The optical components are comprised of a series of selected apertures, T0 and bandwidth choppers, beam scrapers, a fast shutter to limit sample activation, and flight tubes filled with Helium. Techniques such as energy selective, Bragg edge and epithermal imaging will be available at VENUS.

Formative evaluation of a mobile liquid portion size estimation interface for people with varying literacy skills.

PubMed

Chaudry, Beenish Moalla; Connelly, Kay; Siek, Katie A; Welch, Janet L

2013-12-01

Chronically ill people, especially those with low literacy skills, often have difficulty estimating portion sizes of liquids to help them stay within their recommended fluid limits. There is a plethora of mobile applications that can help people monitor their nutritional intake but unfortunately these applications require the user to have high literacy and numeracy skills for portion size recording. In this paper, we present two studies in which the low- and the high-fidelity versions of a portion size estimation interface, designed using the cognitive strategies adults employ for portion size estimation during diet recall studies, was evaluated by a chronically ill population with varying literacy skills. The low fidelity interface was evaluated by ten patients who were all able to accurately estimate portion sizes of various liquids with the interface. Eighteen participants did an in situ evaluation of the high-fidelity version incorporated in a diet and fluid monitoring mobile application for 6 weeks. Although the accuracy of the estimation cannot be confirmed in the second study but the participants who actively interacted with the interface showed better health outcomes by the end of the study. Based on these findings, we provide recommendations for designing the next iteration of an accurate and low literacy-accessible liquid portion size estimation mobile interface.

Lid design for low level waste container

DOEpatents

Holbrook, R.H.; Keener, W.E.

1995-02-28

A container for low level waste includes a shell and a lid. The lid has a frame to which a planar member is welded. The lid frame includes a rectangular outer portion made of square metal tubing, a longitudinal beam extending between axial ends of the rectangular outer portion, and a transverse beam extending between opposite lateral sides of the rectangular outer portion. Two pairs of diagonal braces extend between the longitudinal beam and the four corners of the rectangular outer portion of the frame. 6 figs.

Lid design for low level waste container

DOEpatents

Holbrook, Richard H.; Keener, Wendell E.

1995-01-01

A container for low level waste includes a shell and a lid. The lid has a frame to which a planar member is welded. The lid frame includes a rectangular outer portion made of square metal tubing, a longitudinal beam extending between axial ends of the rectangular outer portion, and a transverse beam extending between opposite lateral sides of the rectangular outer portion. Two pairs of diagonal braces extend between the longitudinal beam and the four corners of the rectangular outer portion of the frame.

29 CFR 1926.1003 - Overhead protection for operators of agricultural and industrial tractors used in construction.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (2) A solid steel sphere or material of equivalent spherical dimension weighing 100 lb (45.4 kg... derived from, and restates, in part, the portions of Society of Automotive Engineers (“SAE”) standard J167...

29 CFR 1926.1003 - Overhead protection for operators of agricultural and industrial tractors used in construction.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (2) A solid steel sphere or material of equivalent spherical dimension weighing 100 lb (45.4 kg... derived from, and restates, in part, the portions of Society of Automotive Engineers (“SAE”) standard J167...

29 CFR 1926.1003 - Overhead protection for operators of agricultural and industrial tractors used in construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (2) A solid steel sphere or material of equivalent spherical dimension weighing 100 lb (45.4 kg... derived from, and restates, in part, the portions of Society of Automotive Engineers (“SAE”) standard J167...

29 CFR 1926.1003 - Overhead protection for operators of agricultural and industrial tractors used in construction.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (2) A solid steel sphere or material of equivalent spherical dimension weighing 100 lb (45.4 kg... derived from, and restates, in part, the portions of Society of Automotive Engineers (“SAE”) standard J167...

29 CFR 1926.1003 - Overhead protection for operators of agricultural and industrial tractors used in construction.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (2) A solid steel sphere or material of equivalent spherical dimension weighing 100 lb (45.4 kg... derived from, and restates, in part, the portions of Society of Automotive Engineers (“SAE”) standard J167...

DIESEL ENGINE RETROFIT TECHNOLOGY VERIFICATION

EPA Science Inventory

This presentation wil be given at the EPA Science Forum 2005 in Washington, DC. According to recent estimates, there are approximately 7.9 million heavy-duty diesel trucks and buses in use in the United States. Emissions from these vehicles account for substantial portions of t...

Differential pressure sensing system for airfoils usable in turbine engines

DOEpatents

Yang, Wen-Ching; Stampahar, Maria E.

2005-09-13

A detection system for identifying airfoils having a cooling systems with orifices that are plugged with contaminants or with showerheads having a portion burned off. The detection system measures pressures at different locations and calculates or measures a differential pressure. The differential pressure may be compared with a known benchmark value to determine whether the differential pressure has changed. Changes in the differential pressure may indicate that one or more of the orifices in a cooling system of an airfoil are plugged or that portions of, or all of, a showerhead has burned off.

Eating vegetables first: the use of portion size to increase vegetable intake in preschool children123

PubMed Central

Spill, Maureen K; Birch, Leann L; Roe, Liane S

2010-01-01

Background: Serving larger portions of low-energy-dense vegetables at a meal could have beneficial effects on children's food and energy intakes. Objective: We investigated whether increasing the portion size of vegetables served at the start of a meal leads to increased vegetable consumption and decreased meal energy intake in children. Design: In a crossover design, 3- to 5-y-old children in a daycare center were served a test lunch once a week for 4 wk (n = 51). In 3 of the meals, a first course of raw carrots varied in portion size (30, 60, or 90 g), and no first course was served in the control meal. Children consumed the first course ad libitum over 10 min and then were served a main course of pasta, broccoli, applesauce, and milk, which was also consumed ad libitum. Results: Total vegetable consumption at the meal increased as the portion size of carrots increased (P < 0.0001). Doubling the portion size of the first course increased carrot consumption by 47%, or 12 ± 2 g (P < 0.0001). Tripling the portion size of carrots, however, did not lead to a further increase in intake (P = 0.61). Meal energy intake was not significantly affected by the amount of carrots served in the first course. The effect of portion size on intake was not significantly influenced by the children's age or body weight status. Conclusion: Increasing the portion size of a vegetable served as a first course can be an effective strategy for increasing vegetable consumption in preschool children. PMID:20219955

An investigation of late-combustion soot burnout in a DI diesel engine using simultaneous planar imaging of soot and OH radical

DOE Office of Scientific and Technical Information (OSTI.GOV)

John E. Dec; Peter L. Kelly-Zion

Diesel engine design continues to be driven by the need to improve performance while at the same time achieving further reductions in emissions. The development of new designs to accomplish these goals requires an understanding of how the emissions are produced in the engine. Laser-imaging diagnostics are uniquely capable of providing this information, and the understanding of diesel combustion and emissions formation has been advanced considerably in recent years by their application. However, previous studies have generally focused on the early and middle stages of diesel combustion. These previous laser-imaging studies do provide important insight into the soot formation andmore » oxidation processes during the main combustion event. They indicate that prior to the end of injection, soot formation is initiated by fuel-rich premixed combustion (equivalence ratio > 4) near the upstream limit of the luminous portion of the reacting fuel jet. The soot is then oxidized at the diffusion flame around the periphery of the luminous plume. Under typical diesel engine conditions, the diffusion flame does not burn the remaining fuel and soot as rapidly as it is supplied, resulting in an expanding region of rich combustion products and soot. This is evident in natural emission images by the increasing size of the luminous soot cloud prior to the end of injection. Hence, the amount of soot in the combustion chamber typically increases until shortly after the end of fuel injection, at which time the main soot formation period ends and the burnout phase begins. Sampling valve and two-color pyrometry data indicate that the vast majority (more than 90%) of the soot formed is oxidized before combustion ends; however, it is generally thought that a small fraction of this soot from the main combustion zones is not consumed and is the source of tail pipe soot emissions.« less

Student Participation in Rover Field Trials

NASA Astrophysics Data System (ADS)

Bowman, C. D.; Arvidson, R. E.; Nelson, S. V.; Sherman, D. M.; Squyres, S. W.

2001-12-01

The LAPIS program was developed in 1999 as part of the Athena Science Payload education and public outreach, funded by the JPL Mars Program Office. For the past three years, the Athena Science Team has been preparing for 2003 Mars Exploration Rover Mission operations using the JPL prototype Field Integrated Design and Operations (FIDO) rover in extended rover field trials. Students and teachers participating in LAPIS work with them each year to develop a complementary mission plan and implement an actual portion of the annual tests using FIDO and its instruments. LAPIS is designed to mirror an end-to-end mission: Small, geographically distributed groups of students form an integrated mission team, working together with Athena Science Team members and FIDO engineers to plan, implement, and archive a two-day test mission, controlling FIDO remotely over the Internet using the Web Interface for Telescience (WITS) and communicating with each other by email, the web, and teleconferences. The overarching goal of LAPIS is to get students excited about science and related fields. The program provides students with the opportunity to apply knowledge learned in school, such as geometry and geology, to a "real world" situation and to explore careers in science and engineering through continuous one-on-one interactions with teachers, Athena Science Team mentors, and FIDO engineers. A secondary goal is to help students develop improved communication skills and appreciation of teamwork, enhanced problem-solving skills, and increased self-confidence. The LAPIS program will provide a model for outreach associated with future FIDO field trials and the 2003 Mars mission operations. The base of participation will be broadened beyond the original four sites by taking advantage of the wide geographic distribution of Athena team member locations. This will provide greater numbers of students with the opportunity to actively engage in rover testing and to explore the possibilities of science, engineering, and technology.

EM-1 Countdown Simulation with Charlie Blackwell-Thompson

NASA Image and Video Library

2018-03-29

Jacobs Test Project Engineer Don Vinton, left and NASA Operations Project Engineer Doug Robertson, monitor operations from his position in Firing Room 1 at the Kennedy Space Center's Launch Control Center during a countdown simulation for Exploration Mission 1. It was the agency's first simulation of a portion of the countdown for the first launch of a Space Launch System rocket and Orion spacecraft that will eventually take astronauts beyond low-Earth orbit to destinations such as the Moon and Mars.

Credit WCT. Photographic copy of photograph, view of Test Stand ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Photographic copy of photograph, view of Test Stand "D" from Test Stand "A" while a rocket engine test is in progress. Cloud of steam is from partly from water created by propellant reaction and from water sprayed by flame bucket into engine exhaust for cooling purposes. A portion of Test Stand "C" is visible at the far right. (JPL negative no. 384-2082-B, 23 October 1959) - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Edwards Air Force Base, Boron, Kern County, CA

EM-1 Countdown Simulation with Charlie Blackwell-Thompson

NASA Image and Video Library

2018-03-29

Liquid Oxygen Systems Engineer Quinten Jones, left and Liquid Oxygen Systems Engineer Andrew "Kody" Smitherman, both of Jacobs, monitor operation from his position in Firing Room 1 at the Kennedy Space Center's Launch Control Center during a countdown simulation for Exploration Mission 1. It was the agency's first simulation of a portion of the countdown for the first launch of a Space Launch System rocket and Orion spacecraft that will eventually take astronauts beyond low-Earth orbit to destinations such as the Moon and Mars.

Alloy chemistry and microstructural control to meet the demands of the automotive Stirling engine

NASA Technical Reports Server (NTRS)

Stephens, Joseph R.

1988-01-01

The automotive Stirling engine now under development by DOE/NASA as an alternative to the internal combustion engine, imposes severe materials requirements for the hot portion of the engine. Materials selected must be low cost and contain a minimum of strategic elements so that availability is not a problem. Heater head tubes contain high pressure hydrogen on the inside and are exposed to hot combustion gases on the outside surface. The cylinders and regenerator housings must be readily castable into complex shapes having varying wall thicknesses and be amenable to brazing and welding operations. Also, high strength, oxidation resistance, resistance to hydrogen permeation, cyclic operation, and long-life are required. A research program conducted by NASA Lewis focused on alloy chemistry and microstructural control to achieve the desired properties over the life of the engine. Results of alloy selection, characterization, evaluation, and actual engine testing of selected materials are presented.

Alloy chemistry and microstructural control to meet the demands of the automotive Stirling engine

NASA Technical Reports Server (NTRS)

Stephens, J. R.

1986-01-01

The automotive Stirling engine now under development by DOE/NASA as an alternative to the internal combustion engine, imposes severe materials requirements for the hot portion of the engine. Materials selected must be low cost and contain a minimum of strategic elements so that availability is not a problem. Heater head tubes contain high pressure hydrogen on the inside and are exposed to hot combustion gases on the outside surface. The cylinders and regenerator housings must be readily castable into complex shapes having varying wall thicknesses and be amenable to brazing and welding operations. Also, high strength, oxidation resistance, resistance to hydrogen permeation, cyclic operation, and long-life are required. A research program conducted by NASA Lewis focused on alloy chemistry and microstructural control to achieve the desired properties over the life of the engine. Results of alloy selection, characterization, evaluation, and actual engine testing of selected materials are presented.

Architecture for removable media USB-ARM

DOEpatents

Shue, Craig A.; Lamb, Logan M.; Paul, Nathanael R.

2015-07-14

A storage device is coupled to a computing system comprising an operating system and application software. Access to the storage device is blocked by a kernel filter driver, except exclusive access is granted to a first anti-virus engine. The first anti-virus engine is directed to scan the storage device for malicious software and report results. Exclusive access may be granted to one or more other anti-virus engines and they may be directed to scan the storage device and report results. Approval of all or a portion of the information on the storage device is based on the results from the first anti-virus engine and the other anti-virus engines. The storage device is presented to the operating system and access is granted to the approved information. The operating system may be a Microsoft Windows operating system. The kernel filter driver and usage of anti-virus engines may be configurable by a user.

40 CFR 90.327 - Sampling system requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Sampling system requirements. 90.327... Equipment Provisions § 90.327 Sampling system requirements. (a) Sample component surface temperature. For sampling systems which use heated components, use engineering judgment to locate the coolest portion of...

40 CFR 90.327 - Sampling system requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Sampling system requirements. 90.327... Equipment Provisions § 90.327 Sampling system requirements. (a) Sample component surface temperature. For sampling systems which use heated components, use engineering judgment to locate the coolest portion of...

Phillips with TVIS hardware in Zvezda

NASA Image and Video Library

2005-09-07

ISS011-E-12608 (7 September 2005) --- Astronaut John L. Phillips, Expedition 11 NASA Space Station science officer and flight engineer, works with a portion of the Treadmill Vibration Isolation System (TVIS) during In-Flight Maintenance (IFM) in the Zvezda Service Module of the International Space Station.

Cognitive engineering models in space systems

NASA Technical Reports Server (NTRS)

Mitchell, Christine M.

1993-01-01

NASA space systems, including mission operations on the ground and in space, are complex, dynamic, predominantly automated systems in which the human operator is a supervisory controller. Models of cognitive functions in complex systems are needed to describe human performance and form the theoretical basis of operator workstation design, including displays, controls, and decision aids. Currently, there several candidate modeling methodologies. They include the Rasmussen abstraction/aggregation hierarchy and decision ladder, the goal-means network, the problem behavior graph, and the operator function model. The research conducted under the sponsorship of this grant focuses on the extension of the theoretical structure of the operator function model and its application to NASA Johnson mission operations and space station applications. The initial portion of this research consists of two parts. The first is a series of technical exchanges between NASA Johnson and Georgia Tech researchers. The purpose is to identify candidate applications for the current operator function model; prospects include mission operations and the Data Management System Testbed. The second portion will address extensions of the operator function model to tailor it to the specific needs of Johnson applications. At this point, we have accomplished two things. During a series of conversations with JSC researchers, we have defined the technical goal of the research supported by this grant to be the structural definition of the operator function model and its computer implementation, OFMspert. Both the OFM and OFMspert have matured to the point that they require infrastructure to facilitate use by researchers not involved in the evolution of the tools. The second accomplishment this year was the identification of the Payload Deployment and Retrieval System (PDRS) as a candidate system for the case study. In conjunction with government and contractor personnel in the Human-Computer Interaction Lab, the PDRS was identified as the most accessible system for the demonstration. Pursuant to this a PDRS simulation was obtained from the HCIL and an initial knowledge engineering effort was conducted to understand the operator's tasks in the PDRS application. The preliminary results of the knowledge engineering effort and an initial formulation of an operator function model (OFM) are contained in the appendices.

Predictors of science, technology, engineering, and mathematics choice options: A meta-analytic path analysis of the social-cognitive choice model by gender and race/ethnicity.

PubMed

Lent, Robert W; Sheu, Hung-Bin; Miller, Matthew J; Cusick, Megan E; Penn, Lee T; Truong, Nancy N

2018-01-01

We tested the interest and choice portion of social-cognitive career theory (SCCT; Lent, Brown, & Hackett, 1994) in the context of science, technology, engineering, and mathematics (STEM) domains. Data from 143 studies (including 196 independent samples) conducted over a 30-year period (1983 through 2013) were subjected to meta-analytic path analyses. The interest/choice model was found to fit the data well over all samples as well as within samples composed primarily of women and men and racial/ethnic minority and majority persons. The model also accounted for large portions of the variance in interests and choice goals within each path analysis. Despite the general predictive utility of SCCT across gender and racial/ethnic groups, we did find that several parameter estimates differed by group. We present both the group similarities and differences and consider their implications for future research, intervention, and theory refinement. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Apollo 14 mission report. Supplement 5: Descent propulsion system final flight evaluation

NASA Technical Reports Server (NTRS)

Avvenire, A. T.; Wood, S. C.

1972-01-01

The performance of the LM-8 descent propulsion system during the Apollo 14 mission was evaluated and found to be satisfactory. The average engine effective specific impulse was 0.1 second higher than predicted, but well within the predicted l sigma uncertainty. The engine performance corrected to standard inlet conditions for the FTP portion of the burn at 43 seconds after ignition was as follows: thrust, 9802, lbf; specific impulse, 304.1 sec; and propellant mixture ratio, 1603. These values are + or - 0.8, -0.06, and + or - 0.3 percent different respectively, from the values reported from engine acceptance tests and were within specification limits.

Aeroheating Predictions for X-34 Using an Inviscid-Boundary Layer Method

NASA Technical Reports Server (NTRS)

Riley, Christopher J.; Kleb, William L.; Alter, Steven J.

1998-01-01

Radiative equilibrium surface temperatures and surface heating rates from a combined inviscid-boundary layer method are presented for the X-34 Reusable Launch Vehicle for several points along the hypersonic descent portion of its trajectory. Inviscid, perfect-gas solutions are generated with the Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) and the Data-Parallel Lower-Upper Relaxation (DPLUR) code. Surface temperatures and heating rates are then computed using the Langley Approximate Three-Dimensional Convective Heating (LATCH) engineering code employing both laminar and turbulent flow models. The combined inviscid-boundary layer method provides accurate predictions of surface temperatures over most of the vehicle and requires much less computational effort than a Navier-Stokes code. This enables the generation of a more thorough aerothermal database which is necessary to design the thermal protection system and specify the vehicle's flight limits.

Assessment of satiety depends on the energy density and portion size of the test meal

PubMed Central

Williams, Rachel A.; Roe, Liane S.; Rolls, Barbara J.

2013-01-01

Objective Foods that enhance satiety can reduce overconsumption, but the availability of large portions of energy-dense foods may counter their benefits. We tested the influence on meal energy intake of varying the energy density and portion size of food consumed after a preload shown to promote satiety. Design and Methods In a crossover design, 46 women were served lunch on six days. On four days they ate a compulsory salad (300 g, 0.33 kcal/g). Unlike previous studies, instead of varying the preload, the subsequent test meal of pasta was varied between standard and increased levels of both energy density (1.25 or 1.66 kcal/g) and portion size (450 or 600 g). On two control days a salad was not served. Results Following the salad, the energy density and portion size of the test meal independently affected meal energy intake (both p<0.02). Serving the higher-energy-dense pasta increased test meal intake by 153±19 kcal and serving the larger portion of pasta increased test meal intake by 40±16 kcal. Compared to having no salad, consuming the salad decreased test meal intake by 123±18 kcal. Conclusions The effect of satiety-enhancing foods can be influenced by the energy density and portion size of other foods at the meal. PMID:23929544

Liquid Rocket Booster Study. Volume 2, Book 1

NASA Technical Reports Server (NTRS)

1989-01-01

The recommended Liquid Rocket Booster (LRB) concept is shown which uses a common main engine with the Advanced Launch System (ALS) which burns LO2 and LH2. The central rationale is based on the belief that the U.S. can only afford one big new rocket engine development in the 1990's. A LO2/LH2 engine in the half million pound thrust class could satisfy STS LRB, ALS, and Shuttle C (instead of SSMEs). Development costs and higher production rates can be shared by NASA and USAF. If the ALS program does not occur, the LO2/RP-1 propellants would produce slight lower costs for and STS LRB. When the planned Booster Engine portion of the Civil Space Transportation Initiatives has provided data on large pressure fed LO2/RP-1 engines, then the choice should be reevaluated.

Double trouble: Portion size and energy density combine to increase preschool children’s lunch intake

PubMed Central

Kling, Samantha M.R.; Roe, Liane S.; Keller, Kathleen L.; Rolls, Barbara J.

2016-01-01

Background Both portion size and energy density (ED) have substantial effects on intake; however, their combined effects on preschool children’s intake have not been examined when multiple foods are varied at a meal. Objective We tested the effects on intake of varying the portion size and ED of lunches served to children in their usual eating environment. Design In a crossover design, lunch was served in 3 childcare centers once a week for 6 weeks to 120 children aged 3 to 5 y. Across the 6 meals, all items were served at 3 levels of portion size (100%, 150%, or 200%) and 2 levels of ED (100% or 142%). The lunch menu had either lowerED or higher-ED versions of chicken, macaroni and cheese, vegetables, applesauce, ketchup, and milk. Children’s ratings of the foods indicated that the lower-ED and higher-ED meals were similarly well liked. Results The weight of food and milk consumed at meals was increased by serving larger portions (P<0.0001) but was unaffected by varying the ED (P=0.22). Meal energy intake, however, was independently affected by portion size and ED (both P<0.0001). Doubling the portions increased energy intake by 24% and increasing meal ED by 42% increased energy intake by 40%. These effects combined to increase intake by 175±12 kcal or 79% at the higherED meal with the largest portions compared to the lower-ED meal with the smallest portions. The foods contributing the most to this increase were chicken, macaroni and cheese, and applesauce. The effects of meal portion size and ED on intake were not influenced by child age or body size, but were significantly affected by parental ratings of child eating behavior. Conclusion Strategically moderating the portion size and ED of foods typically consumed by children could substantially reduce their energy intake without affecting acceptability. PMID:26879105

Getting To Know the "Invisible Web."

ERIC Educational Resources Information Center

Smith, C. Brian

2001-01-01

Discusses the portions of the World Wide Web that cannot be accessed via directories or search engines, explains why they can't be accessed, and offers suggestions for reference librarians to find these sites. Lists helpful resources and gives examples of invisible Web sites which are often databases. (LRW)

Process Dynamics and Control, a Theory-Experiential Approach.

ERIC Educational Resources Information Center

Perna, A. J.; And Others

A required senior-level chemical engineering course at Colorado State University is described. The first nine weeks are devoted to the theory portion of the course, which includes the following topics: LaPlace transformations and time constants, block diagrams, inverse transformations, linearization, frequency response analysis, graphical…

Batteries and Fuel Cells -- Alternative Traction Power for Locomotives and Self-Powered Railcars

DOT National Transportation Integrated Search

1983-03-01

A preliminary study on the application of batteries and fuel cells as alternative motive power to diesel engines has been conducted. Three motive power consists are analyzed using the Boston to New York portion of the Northeast Corridor as a typical ...

19. REGIONAL MAP, SALINAS RIVER PROJECT, CAMP SAN LUIS OBISPO, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. REGIONAL MAP, SALINAS RIVER PROJECT, CAMP SAN LUIS OBISPO, IN CENTRAL PORTION OF SAN LUIS OBISPO, CALIFORNIA. Leeds Hill Barnard & Jewett - Consulting Engineers, February 1942. - Salinas River Project, Cuesta Tunnel, Southeast of U.S. 101, San Luis Obispo, San Luis Obispo County, CA

Coral reefs for coastal protection: A new methodological approach and engineering case study in Grenada.

PubMed

Reguero, Borja G; Beck, Michael W; Agostini, Vera N; Kramer, Philip; Hancock, Boze

2018-03-15

Coastal communities in tropical environments are at increasing risk from both environmental degradation and climate change and require urgent local adaptation action. Evidences show coral reefs play a critical role in wave attenuation but relatively little direct connection has been drawn between these effects and impacts on shorelines. Reefs are rarely assessed for their coastal protection service and thus not managed for their infrastructure benefits, while widespread damage and degradation continues. This paper presents a systematic approach to assess the protective role of coral reefs and to examine solutions based on the reef's influence on wave propagation patterns. Portions of the shoreline of Grenville Bay, Grenada, have seen acute shoreline erosion and coastal flooding. This paper (i) analyzes the historical changes in the shoreline and the local marine, (ii) assess the role of coral reefs in shoreline positioning through a shoreline equilibrium model first applied to coral reef environments, and (iii) design and begin implementation of a reef-based solution to reduce erosion and flooding. Coastline changes in the bay over the past 6 decades are analyzed from bathymetry and benthic surveys, historical imagery, historical wave and sea level data and modeling of wave dynamics. The analysis shows that, at present, the healthy and well-developed coral reefs system in the southern bay keeps the shoreline in equilibrium and stable, whereas reef degradation in the northern bay is linked with severe coastal erosion. A comparison of wave energy modeling for past bathymetry indicates that degradation of the coral reefs better explains erosion than changes in climate and historical sea level rise. Using this knowledge on how reefs affect the hydrodynamics, a reef restoration solution is designed and studied to ameliorate the coastal erosion and flooding. A characteristic design provides a modular design that can meet specific engineering, ecological and implementation criteria. Four pilot units were implemented in 2015 and are currently being field-tested. This paper presents one of the few existing examples available to date of a reef restoration project designed and engineered to deliver risk reduction benefits. The case study shows how engineering and ecology can work together in community-based adaptation. Our findings are particularly important for Small Island States on the front lines of climate change, who have the most to gain from protecting and managing coral reefs as coastal infrastructure. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Integrating Safety Assessment Methods using the Risk Informed Safety Margins Characterization (RISMC) Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis Smith; Diego Mandelli

Safety is central to the design, licensing, operation, and economics of nuclear power plants (NPPs). As the current light water reactor (LWR) NPPs age beyond 60 years, there are possibilities for increased frequency of systems, structures, and components (SSC) degradations or failures that initiate safety significant events, reduce existing accident mitigation capabilities, or create new failure modes. Plant designers commonly “over-design” portions of NPPs and provide robustness in the form of redundant and diverse engineered safety features to ensure that, even in the case of well-beyond design basis scenarios, public health and safety will be protected with a very highmore » degree of assurance. This form of defense-in-depth is a reasoned response to uncertainties and is often referred to generically as “safety margin.” Historically, specific safety margin provisions have been formulated primarily based on engineering judgment backed by a set of conservative engineering calculations. The ability to better characterize and quantify safety margin is important to improved decision making about LWR design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margin management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. In addition, as research and development (R&D) in the LWR Sustainability (LWRS) Program and other collaborative efforts yield new data, sensors, and improved scientific understanding of physical processes that govern the aging and degradation of plant SSCs needs and opportunities to better optimize plant safety and performance will become known. To support decision making related to economics, readability, and safety, the RISMC Pathway provides methods and tools that enable mitigation options known as margins management strategies. The purpose of the RISMC Pathway R&D is to support plant decisions for risk-informed margin management with the aim to improve economics, reliability, and sustain safety of current NPPs. As the lead Department of Energy (DOE) Laboratory for this Pathway, the Idaho National Laboratory (INL) is tasked with developing and deploying methods and tools that support the quantification and management of safety margin and uncertainty.« less

Drag and Cooling with Various Forms of Cowling for a "Whirlwind" Radial Air-cooled Engine II

NASA Technical Reports Server (NTRS)

Weick, Fred E

1930-01-01

This report gives the results of the second portion of an investigation in the twenty-foot Propeller Research Tunnel of the National Advisory Committee for Aeronautics, on the cowling and cooling of a "Whirlwind" J-5 radial air-cooled engine. The first portion pertains to tests with a cabin fuselage. This report covers tests with several forms of cowling, including conventional types, individual fairings behind the cylinders, individual hoods over the over the cylinders, and the new N. A. C. A. complete cowling, all on an open cockpit fuselage. Drag tests were also made with a conventional engine nacelle, and with a nacelle having the new complete cowling. In the second part of the investigation the results found in the first part were substantiated. It was also found that the reduction in drag with the complete cowling over that with conventional cowling is greater with the smaller bodies than with the cabin fuselage; in fact, the gain in the case of the completely cowled nacelle is over twice that with the cabin fuselage. The individual fairings and hoods did not prove effective in reducing the drag. The results of flight tests on AT-5A airplane has been analyzed and found to agree very well with the results of the wind tunnel tests. (author)

Capillary Flow in Containers of Polygonal Section: Theory and Experiment

NASA Technical Reports Server (NTRS)

Weislogel, Mark M.; Rame, Enrique (Technical Monitor)

2001-01-01

An improved understanding of the large-length-scale capillary flows arising in a low-gravity environment is critical to that engineering community concerned with the design and analysis of spacecraft fluids management systems. Because a significant portion of liquid behavior in spacecraft is capillary dominated it is natural to consider designs that best exploit the spontaneous character of such flows. In the present work, a recently verified asymptotic analysis is extended to approximate spontaneous capillary flows in a large class of cylindrical containers of irregular polygonal section experiencing a step reduction in gravitational acceleration. Drop tower tests are conducted using partially-filled irregular triangular containers for comparison with the theoretical predictions. The degree to which the experimental data agree with the theory is a testament to the robustness of the basic analytical assumption of predominantly parallel flow. As a result, the closed form analytical expressions presented serve as simple, accurate tools for predicting bulk flow characteristics essential to practical low-g system design and analysis. Equations for predicting corner wetting rates, total container flow rates, and transient surfaces shapes are provided that are relevant also to terrestrial applications such as capillary flow in porous media.

Osteogenic properties of a short BMP-2 chimera peptide.

PubMed

Falcigno, Lucia; D'Auria, Gabriella; Calvanese, Luisa; Marasco, Daniela; Iacobelli, Roberta; Scognamiglio, Pasqualina L; Brun, Paola; Danesin, Roberta; Pasqualin, Matteo; Castagliuolo, Ignazio; Dettin, Monica

2015-09-01

Bone morphogenetic proteins (BMPs) play a key role in bone and cartilage formation. For these properties, BMPs are employed in the field of tissue engineering to induce bone regeneration in damaged tissues. To overcome drawbacks due to the use of entire proteins, synthetic peptides derived from their parent BMPs have come out as promising molecules for biomaterial design. On the structural ground of the experimental BMP-2 receptor complexes reported in the literature, we designed three peptides, reproducing the BMP-2 region responsible for the binding to the type II receptor, ActRIIB. These peptides were characterized by NMR, and the structural features of the peptide-receptor binding interface were highlighted by docking experiments. Peptide-receptor binding affinities were analyzed by means of ELISA and surface plasmon resonance techniques. Furthermore, cellular assays were performed to assess their osteoinductive properties. A chimera peptide, obtained by combining the sequence portions 73-92 and 30-34 of BMP-2, shows the best affinity for ActRIIB in the series and represents a good starting point for the design of new compounds able to reproduce osteogenic properties of the parent BMP-2. Copyright © 2015 European Peptide Society and John Wiley & Sons, Ltd.

Algorithms for a Closed-Loop Artificial Pancreas: The Case for Model Predictive Control

PubMed Central

Bequette, B. Wayne

2013-01-01

The relative merits of model predictive control (MPC) and proportional-integral-derivative (PID) control are discussed, with the end goal of a closed-loop artificial pancreas (AP). It is stressed that neither MPC nor PID are single algorithms, but rather are approaches or strategies that may be implemented very differently by different engineers. The primary advantages to MPC are that (i) constraints on the insulin delivery rate (and/or insulin on board) can be explicitly included in the control calculation; (ii) it is a general framework that makes it relatively easy to include the effect of meals, exercise, and other events that are a function of the time of day; and (iii) it is flexible enough to include many different objectives, from set-point tracking (target) to zone (control to range). In the end, however, it is recognized that the control algorithm, while important, represents only a portion of the effort required to develop a closed-loop AP. Thus, any number of algorithms/approaches can be successful—the engineers involved in the design must have experience with the particular technique, including the important experience of implementing the algorithm in human studies and not simply through simulation studies. PMID:24351190

Variable-geometry turbocharger with asymmetric divided volute for engine exhaust gas pulse optimization

DOEpatents

Serres, Nicolas

2010-11-09

A turbine assembly for a variable-geometry turbocharger includes a turbine housing defining a divided volute having first and second scrolls, wherein the first scroll has a substantially smaller volume than the second scroll. The first scroll feeds exhaust gas to a first portion of a turbine wheel upstream of the throat of the wheel, while the second scroll feeds gas to a second portion of the wheel at least part of which is downstream of the throat. Flow from the second scroll is regulated by a sliding piston. The first scroll can be optimized for low-flow conditions such that the turbocharger can operate effectively like a small fixed-geometry turbocharger when the piston is closed. The turbine housing defines an inlet that is divided by a dividing wall into two portions respectively feeding gas to the two scrolls, a leading edge of the dividing wall being downstream of the inlet mouth.

Modeling Commercial Turbofan Engine Icing Risk With Ice Crystal Ingestion

NASA Technical Reports Server (NTRS)

Jorgenson, Philip C. E.; Veres, Joseph P.

2013-01-01

The occurrence of ice accretion within commercial high bypass aircraft turbine engines has been reported under certain atmospheric conditions. Engine anomalies have taken place at high altitudes that have been attributed to ice crystal ingestion, partially melting, and ice accretion on the compression system components. The result was degraded engine performance, and one or more of the following: loss of thrust control (roll back), compressor surge or stall, and flameout of the combustor. As ice crystals are ingested into the fan and low pressure compression system, the increase in air temperature causes a portion of the ice crystals to melt. It is hypothesized that this allows the ice-water mixture to cover the metal surfaces of the compressor stationary components which leads to ice accretion through evaporative cooling. Ice accretion causes a blockage which subsequently results in the deterioration in performance of the compressor and engine. The focus of this research is to apply an engine icing computational tool to simulate the flow through a turbofan engine and assess the risk of ice accretion. The tool is comprised of an engine system thermodynamic cycle code, a compressor flow analysis code, and an ice particle melt code that has the capability of determining the rate of sublimation, melting, and evaporation through the compressor flow path, without modeling the actual ice accretion. A commercial turbofan engine which has previously experienced icing events during operation in a high altitude ice crystal environment has been tested in the Propulsion Systems Laboratory (PSL) altitude test facility at NASA Glenn Research Center. The PSL has the capability to produce a continuous ice cloud which are ingested by the engine during operation over a range of altitude conditions. The PSL test results confirmed that there was ice accretion in the engine due to ice crystal ingestion, at the same simulated altitude operating conditions as experienced previously in flight. The computational tool was utilized to help guide a portion of the PSL testing, and was used to predict ice accretion could also occur at significantly lower altitudes. The predictions were qualitatively verified by subsequent testing of the engine in the PSL. The PSL test has helped to calibrate the engine icing computational tool to assess the risk of ice accretion. The results from the computer simulation identified prevalent trends in wet bulb temperature, ice particle melt ratio, and engine inlet temperature as a function of altitude for predicting engine icing risk due to ice crystal ingestion.

Gas Generator Feedline Orifice Sizing Methodology: Effects of Unsteadiness and Non-Axisymmetric Flow

NASA Technical Reports Server (NTRS)

Rothermel, Jeffry; West, Jeffrey S.

2011-01-01

Engine LH2 and LO2 gas generator feed assemblies were modeled with computational fluid dynamics (CFD) methods at 100% rated power level, using on-center square- and round-edge orifices. The purpose of the orifices is to regulate the flow of fuel and oxidizer to the gas generator, enabling optimal power supply to the turbine and pump assemblies. The unsteady Reynolds-Averaged Navier-Stokes equations were solved on unstructured grids at second-order spatial and temporal accuracy. The LO2 model was validated against published experimental data and semi-empirical relationships for thin-plate orifices over a range of Reynolds numbers. Predictions for the LO2 square- and round-edge orifices precisely match experiment and semi-empirical formulas, despite complex feedline geometry whereby a portion of the flow from the engine main feedlines travels at a right-angle through a smaller-diameter pipe containing the orifice. Predictions for LH2 square- and round-edge orifice designs match experiment and semi-empirical formulas to varying degrees depending on the semi-empirical formula being evaluated. LO2 mass flow rate through the square-edge orifice is predicted to be 25 percent less than the flow rate budgeted in the original engine balance, which was subsequently modified. LH2 mass flow rate through the square-edge orifice is predicted to be 5 percent greater than the flow rate budgeted in the engine balance. Since CFD predictions for LO2 and LH2 square-edge orifice pressure loss coefficients, K, both agree with published data, the equation for K has been used to define a procedure for orifice sizing.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 51: Workplace communications skills and the value of communications and information-use skills instruction: Engineering students' perspectives

NASA Technical Reports Server (NTRS)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1995-01-01

Studies indicate that communications and information-related activities take up a substantial portion of an engineer's work week; therefore, effective communications and information use skills are one of the key engineering competencies that recent graduates of engineering programs are expected to possess. Feedback from industry rates communications and information use skills of entry-level engineers low. Missing from current discussions of communications and information use skills and competencies for engineering students is a clear explanation from the professional engineering community about what constitutes 'acceptable and desirable communications and information norms' within that community. To gather adequate and generalizable data about communications and information skills instruction and to provide a student perspective on the communications skills of engineers, we undertook a national study of aerospace engineering students in March 1993. The study included questions about the importance of certain communications and information skills to professional success, the instruction students had received in these skills, and perceived helpfulness of the instruction. Selected results from the study study are reported in this paper.

Design and Integration of a Rotor Alone Nacelle for Acoustic Fan Testing

NASA Technical Reports Server (NTRS)

Shook, Tony D.; Hughes, Christoper E.; Thompson, William K.; Tavernelli, Paul F.; Cunningham, Cameron C.; Shah, Ashwin

2001-01-01

A brief summary of the design, integration and testing of a rotor alone nacelle (RAN) in NASA Glenn's 9'x 15' Low Speed Wind Tunnel (LSWT) is presented. The purpose of the RAN system was to provide an "acoustically clean" flow path within the nacelle to isolate that portion of the total engine system acoustic signature attributed to fan noise. The RAN design accomplished this by removing the stators that provided internal support to the nacelle. In its place, two external struts mounted to a two-axis positioning table located behind the tunnel wall provided the support. Nacelle-mounted lasers and a closed-loop control system provided the input to the table to maintain nacelle to fan concentricity as thermal and thrust loads displaced the strut-mounted fan. This unique design required extensive analysis and verification testing to ensure the safety of the fan model, propulsion simulator drive rig, and facility, along with experimental consistency of acoustic data obtained while using the RAN system. Initial testing was used to optimize the positioning system and resulted in concentricity errors of +/- 0.0031 in. in the horizontal direction and +0.0035/-0.0013 in, in the vertical direction. As a result of successful testing, the RAN system will be transitioned into other acoustic research programs at NASA Glenn Research Center.

Visually Coupled Systems (VCS): The Virtual Panoramic Display (VPD) System

NASA Technical Reports Server (NTRS)

Kocian, Dean F.

1992-01-01

The development and impact is described of new visually coupled system (VCS) equipment designed to support engineering and human factors research in the military aircraft cockpit environment. VCS represents an advanced man-machine interface (MMI). Its potential to improve aircrew situational awareness seems enormous, but its superiority over the conventional cockpit MMI has not been established in a conclusive and rigorous fashion. What has been missing is a 'systems' approach to technology advancement that is comprehensive enough to produce conclusive results concerning the operational viability of the VCS concept and verify any risk factors that might be involved with its general use in the cockpit. The advanced VCS configuration described here, was ruggedized for use in military aircraft environments and was dubbed the Virtual Panoramic Display (VPD). It was designed to answer the VCS portion of the systems problem, and is implemented as a modular system whose performance can be tailored to specific application requirements. The overall system concept and the design of the two most important electronic subsystems that support the helmet mounted parts, a new militarized version of the magnetic helmet mounted sight and correspondingly similar helmet display electronics, are discussed in detail. Significant emphasis is given to illustrating how particular design features in the hardware improve overall system performance and support research activities.

Cyanochrome fluorophores

DOEpatents

Ulijasz, Andrew T.; Vierstra, Richard D.

2016-06-14

Genetically-engineered cyanochrome fluorophore molecules (fluorophores) with increased fluorescence and with absorbing fluorescence in the blue and green (blue/green) portion of the light spectrum are provided. These fluorophores are derived from the domains of phytochromes, and in particular cyanobacterial phytochromes. Methods for generating these fluorophores and various applications of these fluorophores are also provided.

Carbon-carbon grid for ion engines

NASA Technical Reports Server (NTRS)

Garner, Charles E. (Inventor)

1993-01-01

A method and apparatus of manufacturing a grid member for use in an ion discharge apparatus provides a woven carbon fiber in a matrix of carbon. The carbon fibers are orientated to provide a negatibe coefficient of thermal expansion for at least a portion of the grid member's operative range of use.

Carbon-carbon grid for ion engines

NASA Technical Reports Server (NTRS)

Garner, Charles E. (Inventor)

1995-01-01

A method and apparatus of manufacturing a grid member for use in an ion discharge apparatus provides a woven carbon fiber in a matrix of carbon. The carbon fibers are orientated to provide a negatibe coefficient of thermal expansion for at least a portion of the grid member's operative range of use.

32 CFR 34.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Basic, applied, and advanced research activities. Basic research is defined as efforts directed toward increasing knowledge or understanding in science and engineering. Applied research is defined as efforts that...). TIAs are covered by part 37 of the DoDGARs (32 CFR part 37). Portions of this part may apply to a TIA...

49 CFR 830.5 - Immediate notification.

Code of Federal Regulations, 2011 CFR

2011-10-01

... any internal turbine engine component that results in the escape of debris other than out the exhaust... utilized. (8) Release of all or a portion of a propeller blade from an aircraft, excluding release caused... airspace. (11) Damage to helicopter tail or main rotor blades, including ground damage, that requires major...

49 CFR 830.5 - Immediate notification.

Code of Federal Regulations, 2014 CFR

2014-10-01

... any internal turbine engine component that results in the escape of debris other than out the exhaust... utilized. (8) Release of all or a portion of a propeller blade from an aircraft, excluding release caused... airspace. (11) Damage to helicopter tail or main rotor blades, including ground damage, that requires major...

49 CFR 830.5 - Immediate notification.

Code of Federal Regulations, 2012 CFR

2012-10-01

... any internal turbine engine component that results in the escape of debris other than out the exhaust... utilized. (8) Release of all or a portion of a propeller blade from an aircraft, excluding release caused... airspace. (11) Damage to helicopter tail or main rotor blades, including ground damage, that requires major...

49 CFR 830.5 - Immediate notification.

Code of Federal Regulations, 2013 CFR

2013-10-01

... any internal turbine engine component that results in the escape of debris other than out the exhaust... utilized. (8) Release of all or a portion of a propeller blade from an aircraft, excluding release caused... airspace. (11) Damage to helicopter tail or main rotor blades, including ground damage, that requires major...

Virtues and Limitations of Risk Analysis

ERIC Educational Resources Information Center

Weatherwax, Robert K.

1975-01-01

After summarizing the Rasmussion Report, the author reviews the probabilistic portion of the report from the perspectives of engineering utility and risk assessment uncertainty. The author shows that the report may represent a significant step forward in the assurance of reactor safety and an imperfect measure of actual reactor risk. (BT)

Coherent Turbulence Rig in the Engine Research Building

NASA Image and Video Library

1979-08-21

An engineer examines the Coherent Turbulence Rig in the Engine Research Building at the National Aeronautics and Space Administration (NASA) Lewis Research Center. Coherent turbulence occurs when waves of uniform size and alignment are present in airflow. Researchers at NASA Lewis were interested in determining the relation between the size of the waves and their heat transfer properties. The massive 4.25-acre Engine Research Building contains dozens of test cells, test stands, and altitude chambers. A powerful a collection of compressors and exhausters located in the central portion of the basement provides process air and exhaust for these test areas. This system is connected to similar process air systems in the laboratory’s other large test facilities. The Central Control Room coordinates this activity and communicates with the local utilities.

FACILITY 858, PORTION OF NORTHEAST SIDE (APRON AVENUE SIDE), SHOWING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FACILITY 858, PORTION OF NORTHEAST SIDE (APRON AVENUE SIDE), SHOWING CHEVRON DESIGN OVER FORMER PASSAGEWAY, OBLIQUE VIEW FACING WEST. - Schofield Barracks Military Reservation, Quadrangle K Barracks Type, Between Wilson Street & Capron Avenue near Williston Avenue, Wahiawa, Honolulu County, HI

Internal combustion engine

DOEpatents

Baker, Quentin A.; Mecredy, Henry E.; O'Neal, Glenn B.

1991-01-01

An improved engine is provided that more efficiently consumes difficult fuels such as coal slurries or powdered coal. The engine includes a precombustion chamber having a portion thereof formed by an ignition plug. The precombustion chamber is arranged so that when the piston is proximate the head, the precombustion chamber is sealed from the main cylinder or the main combustion chamber and when the piston is remote from the head, the precombustion chamber and main combustion chamber are in communication. The time for burning of fuel in the precombustion chamber can be regulated by the distance required to move the piston from the top dead center position to the position wherein the precombustion chamber and main combustion chamber are in communication.

Low emission turbo compound engine system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vuk,; Carl, T

2011-05-31

A diesel or HHCI engine has an air intake and an exhaust for products of combustion. A pair of turbochargers receive the products of combustion in a series relationship and an exhaust aftertreatment device receive the products of combustion from the downstream turbine. A power turbine receives the output from the exhaust aftertreatment device and an EGR system of the power turbine passes a selected portion of the output to a point upstream of the upstream turbocharger compressor. A device adds fuel to the aftertreatment device to regenerate the particulate filter and the power turbine recoups the additional energy. Themore » power turbine may be used to drive accessories or the prime output of the engine.« less

Sequestration of carbon dioxide with hydrogen to useful products

DOEpatents

Adams, Michael W. W.; Kelly, Robert M.; Hawkins, Aaron B.; Menon, Angeli Lal; Lipscomb, Gina Lynette Pries; Schut, Gerrit Jan

2017-03-07

Provided herein are genetically engineered microbes that include at least a portion of a carbon fixation pathway, and in one embodiment, use molecular hydrogen to drive carbon dioxide fixation. In one embodiment, the genetically engineered microbe is modified to convert acetyl CoA, molecular hydrogen, and carbon dioxide to 3-hydroxypropionate, 4-hydroxybutyrate, acetyl CoA, or the combination thereof at levels greater than a control microbe. Other products may also be produced. Also provided herein are cell free compositions that convert acetyl CoA, molecular hydrogen, and carbon dioxide to 3-hydroxypropionate, 4-hydroxybutyrate, acetyl CoA, or the combination thereof. Also provided herein are methods of using the genetically engineered microbes and the cell free compositions.

Collaborative Research on the Ultra High Bypass Ratio Engine Cycle to Reduce Noise, Emissions and Fuel Consumption

NASA Technical Reports Server (NTRS)

Hughes, Christopher

2008-01-01

A pictorial history of NASA development of advanced engine technologies for reducing environmental emissions and increasing performance from the 1970s to present is presented. The goals of the Subsonic Fixed Wing Program portion of the NASA Fundamental Aeronautics Program are addressed, along with the areas of investigation currently being pursued by the Ultra High Bypass Partnership Element of the Subsonic Fixed Wing Program to meet the goals. Ultra High Bypass cycle research collaboration successes with Pratt & Whitney are presented.

EMISSIONS FROM COMBUSTION OF POST-CONSUMER ...

EPA Pesticide Factsheets

Symposium Paper The Portland cement industry is interested in the utilization of post-consumer carpet as a fuel to replace a portion of its traditional fuels. In response to this interest, the Carpet and Rug Institute, US Department of Energy, Georgia Institute of Technology School of Chemical and Biomolecular Engineering, US Environmental Protection Agency, Lehigh Cement Company, and the American Society of Mechanical Engineers Research Committee on Industrial and Municipal Waste are performing a collaborative program to assess the feasibility of using cement kilns for the destruction of post-consumer carpet.

Supersonics Project: Airport Noise Technical Challenge

NASA Technical Reports Server (NTRS)

Bridges, James E.

2008-01-01

This presentation gives an overview of the work being done under the Airport Noise Technical Challenge portion of the Supersonics Project in the Fundamental Aeronautics Program. The objective of the Challenge is to provide technology (e.g. low noise nozzle concepts) and engineering tools required for a viable supersonic aircraft. To accomplish this we have activities divided into Prediction, Diagnostics, and Engineering elements. Each of the tasks reviewed here have potential applications to work being done at other flight regimes and other aircraft and are of interest to the Acoustics Technical Working Group.

Mixer assembly for a gas turbine engine having a pilot mixer with a corner flame stabilizing recirculation zone

NASA Technical Reports Server (NTRS)

Dai, Zhongtao (Inventor); Cohen, Jeffrey M. (Inventor); Fotache, Catalin G. (Inventor)

2012-01-01

A mixer assembly for a gas turbine engine is provided, including a main mixer, and a pilot mixer having an annular housing in which a corner is formed between an aft portion of the housing and a bulkhead wall in which a corner recirculation zone is located to stabilize and anchor the flame of the pilot mixer. The pilot mixer can further include features to cool the annular housing, including in the area of the corner recirculation zone.

F-16XL Ship #2 during last flight viewed from below showing shock fence on left wing

NASA Technical Reports Server (NTRS)

1996-01-01

A special 'shock fence' installed beneath the leading edge of the left wing is visible in this underside aerial view of NASA's F-16XL #2 research aircraft. The small structure assisted researchers in NASA's Supersonic Laminar Flow Control (SLFC) program in controlling the shock wave coming off the F-16XL's engine air inlet when the craft flew at speeds above Mach 1, or the speed of sound. The two-seat F-16XL, one of two 'XLs' flown by NASA's Drdyen Flight Research Center, Edwards, California, flew 45 missions comprising over 90 flight hours during the SLFC project, much of it at supersonic speeds up to Mach 2 and altitudes up to 55,000 feet. The project demonstrated that laminar -- or smooth -- airflow could be achieved over a major portion of a wing at supersonic speeds by use of a suction system. Data acquired during the program will be used to develop a design code calibration database which could assist designers in reducing aerodynamic drag of a proposed second-generation supersonic transport.

Mission Systems Engineering (MSE) for the Cosmic Evolution Through UV Spectroscopy (CETUS) Space Telescope Concept

NASA Technical Reports Server (NTRS)

Purves, Lloyd R.

2017-01-01

The basic objectives of the CETUS mission are to significantly improve our understanding of the evolution of galaxies at a redshift (z) of approximately 1 and to meet the cost constraints (1$B) for a NASA Probe-Class mission. What makes these galaxies so interesting is that their light, which has taken about 7 billion years to reach us, comes from a time when star-formation in the observable universe peaked, and the processes behind this peaking are far from well understood. To accomplish its science goals, CETUS needs to get UV spectra of 105 of these galaxies. To help meet its cost constraints, CETUS will only observe galaxies for which VIS spectra are already available, which means that CETUS has to survey a specific portion of the sky. The combination of the CETUS measurement goals and costs constraints strongly influence the design of virtually every aspect of the mission starting from the telescope and instruments, through to orbit and launch vehicle selection, and including the design of most of the SC Bus sub-systems, such as structure, ACS, power, communications, and thermal control.

A space systems perspective of graphics simulation integration

NASA Technical Reports Server (NTRS)

Brown, R.; Gott, C.; Sabionski, G.; Bochsler, D.

1987-01-01

Creation of an interactive display environment can expose issues in system design and operation not apparent from nongraphics development approaches. Large amounts of information can be presented in a short period of time. Processes can be simulated and observed before committing resources. In addition, changes in the economics of computing have enabled broader graphics usage beyond traditional engineering and design into integrated telerobotics and Artificial Intelligence (AI) applications. The highly integrated nature of space operations often tend to rely upon visually intensive man-machine communication to ensure success. Graphics simulation activities at the Mission Planning and Analysis Division (MPAD) of NASA's Johnson Space Center are focusing on the evaluation of a wide variety of graphical analysis within the context of present and future space operations. Several telerobotics and AI applications studies utilizing graphical simulation are described. The presentation includes portions of videotape illustrating technology developments involving: (1) coordinated manned maneuvering unit and remote manipulator system operations, (2) a helmet mounted display system, and (3) an automated rendezous application utilizing expert system and voice input/output technology.

High-Speed Ring Bus

NASA Technical Reports Server (NTRS)

Wysocky, Terry; Kopf, Edward, Jr.; Katanyoutananti, Sunant; Steiner, Carl; Balian, Harry

2010-01-01

The high-speed ring bus at the Jet Propulsion Laboratory (JPL) allows for future growth trends in spacecraft seen with future scientific missions. This innovation constitutes an enhancement of the 1393 bus as documented in the Institute of Electrical and Electronics Engineers (IEEE) 1393-1999 standard for a spaceborne fiber-optic data bus. It allows for high-bandwidth and time synchronization of all nodes on the ring. The JPL ring bus allows for interconnection of active units with autonomous operation and increased fault handling at high bandwidths. It minimizes the flight software interface with an intelligent physical layer design that has few states to manage as well as simplified testability. The design will soon be documented in the AS-1393 standard (Serial Hi-Rel Ring Network for Aerospace Applications). The framework is designed for "Class A" spacecraft operation and provides redundant data paths. It is based on "fault containment regions" and "redundant functional regions (RFR)" and has a method for allocating cables that completely supports the redundancy in spacecraft design, allowing for a complete RFR to fail. This design reduces the mass of the bus by incorporating both the Control Unit and the Data Unit in the same hardware. The standard uses ATM (asynchronous transfer mode) packets, standardized by ITU-T, ANSI, ETSI, and the ATM Forum. The IEEE-1393 standard uses the UNI form of the packet and provides no protection for the data portion of the cell. The JPL design adds optional formatting to this data portion. This design extends fault protection beyond that of the interconnect. This includes adding protection to the data portion that is contained within the Bus Interface Units (BIUs) and by adding to the signal interface between the Data Host and the JPL 1393 Ring Bus. Data transfer on the ring bus does not involve a master or initiator. Following bus protocol, any BIU may transmit data on the ring whenever it has data received from its host. There is no centralized arbitration or bus granting. The JPL design provides for autonomous synchronization of the nodes on the ring bus. An address-synchronous latency adjust buffer (LAB) has been designed that cannot get out of synchronization and needs no external input. Also, a priority-driven cable selection behavior has been programmed into each unit on the ring bus. This makes the bus able to connect itself up, according to a maximum redundancy priority system, without the need for computer intervention at startup. Switching around a failed or switched-off unit is also autonomous. The JPL bus provides a map of all the active units for the host computer to read and use for fault management. With regard to timing, this enhanced bus recognizes coordinated timing on a spacecraft as critical and addresses this with a single source of absolute and relative time, which is broadcast to all units on the bus with synchronization maintained to the tens of nanoseconds. Each BIU consists of up to five programmable triggers, which may be programmed for synchronization of events within the spacecraft of instrument. All JPL-formatted data transmitted on the ring bus are automatically time-stamped.

Piloting a fiber optics and electronic theory curriculum with high school students

NASA Astrophysics Data System (ADS)

Gilchrist, Pamela O.; Carpenter, Eric D.; Gray-Battle, Asia

2014-07-01

Previous participants from a multi-year blended learning intervention focusing on science, technology, engineering and mathematics (STEM) content knowledge, technical, college, and career preparatory skills were recruited to pilot a new module designed by the project staff. Participants met for a total of 22 contact hours receiving lectures from staff and two guest speakers from industries relevant to photonics, fiber optics hands-on experimentation, and practice with documenting progress. Activities included constructing a fiber optics communication system, troubleshooting breadboard circuits and diagrammed circuits as well as hypothesis testing to discover various aspects of fiber optic cables. Participants documented their activities, wrote reflections on the content and learning endeavor and gave talks about their research experiences to staff, peers, and relatives during the last session. Overall, it was found that a significant gain in content knowledge occurred between the time of pre-testing (Mean=0.54) and post-testing time points for the fiber optics portion of the curriculum via the use of a paired samples t-test (Mean=0.71), t=-2.72, p<.05. Additionally, the electronic theory test results were not a normal distribution and for this reason non-parametric testing was used, specifically a Wilcoxon signed-ranks test. Results indicated a significant increase in content knowledge occurred over time between the pre- (Mdn=0.35) and post-testing time points (Mdn=0.80) z=-2.49, p<,05, r=-0.59 for the electronic theory portion of the curriculum. An equivalent control group was recruited from the remaining participant pool, allowing for comparison between groups. The program design, findings, and lessons learned will be reported in this paper.

Regulatory guidance on soil cover systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kane, J.D.

1991-12-31

The US Nuclear Regulatory Commission (NRC) in September 1991, completed revisions to 14 sections of the Standard Review Plan (SRP) for the Review of a License Application for a Low-Level Radioactive Waste Disposal Facility. The major purposes of the SRP are to ensure the quality and uniformity of the NRC staff`s safety reviews, and to present a well-defined base from which to evaluate the acceptability of information and data provided in the Safety Analysis Report (SAR) portion of the license application. SRP 3.2, entitled, Design Considerations for Normal and Abnormal/Accident Conditions, was one of the sections that was revised bymore » the NRC staff. This revision was completed to provide additional regulatory guidance on the important considerations that need to be addressed for the proper design and construction of soil cover systems that are to be placed over the LLW. The cover system over the waste is acknowledged to be one of the most important engineered barriers for the long-term stable performance of the disposal facility. The guidance in revised SRP 3.2 summarizes the previous efforts and recommendations of the US Army Corps of Engineers (COE), and a peer review panel on the placement of soil cover systems. NRC published these efforts in NUREG/CR-5432. The discussions in this paper highlight selected recommendations on soil cover issues that the NRC staff considers important for ensuring the safe, long-term performance of the soil cover systems. The development phases to be discussed include: (1) cover design; (2) cover material selection; (3) laboratory and field testing; (4) field placement control and acceptance; and (5) penetrations through the constructed covers.« less

Two-dimensional magnesium oxide nanosheets reinforced epoxy nanocomposites for enhanced fracture toughness

NASA Astrophysics Data System (ADS)

Balguri, Praveen Kumar; Harris Samuel, D. G.; Guruvishnu, T.; Aditya, D. B.; Mahadevan, S. M.; Thumu, Udayabhaskararao

2018-01-01

Metal oxide nanoparticles have been used as excellent reinforcements to enhance mechanical properties of polymers, natural composites, and ceramics. To date, a major portion of metal oxides used as nanofillers is three dimensional spherical nanoparticles. In the last decade, two-dimensional (2D) materials such as graphene have been widely investigated to improve the mechanical and electrical properties of polymer materials. In this paper, 2D Magnesium oxide (MgO) nanosheets reinforced epoxy composites (0.1, 0.2 and 0.4 wt%) are fabricated and studied for their ability to resist the propagation of preexisting flaw by conducting fracture toughness test for K IC, critical stress intensity factor. This property is an important mechanical property for designing applications in various engineering technologies. Our results show that the MgO with 0.2 wt% is the optimized level to improve the fracture toughness of the epoxy polymer by 47%.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schonewill, Philip P.; Berglin, Eric J.; Boeringa, Gregory K.

At the request of the U.S. Department of Energy Office of River Protection, Pacific Northwest National Laboratory (PNNL) conducted a scoping study to investigate supplemental technologies for supplying vertical fluid motion and enhanced mixing in Waste Treatment and Immobilization Plant (WTP) vessels designed for high solids processing. The study assumed that the pulse jet mixers adequately mix and shear the bottom portion of a vessel. Given that, the primary function of a supplemental technology should be to provide mixing and shearing in the upper region of a vessel. The objective of the study was to recommend a mixing technology andmore » configuration that could be implemented in the 8-ft test vessel located at Mid-Columbia Engineering (MCE). Several mixing technologies, primarily airlift circulator (ALC) systems, were evaluated in the study. This technical report contains a review of ALC technologies, a description of the PNNL testing and accompanying results, and recommended features of an ALC system for further study.« less

A Simple Engineering Analysis of Solar Particle Event High Energy Tails and Their Impact on Vehicle Design

NASA Technical Reports Server (NTRS)

Singleterry, Robert C., Jr.; Walker, Steven A.; Clowdsley, Martha S.

2016-01-01

The mathematical models for Solar Particle Event (SPE) high energy tails are constructed with several di erent algorithms. Since limited measured data exist above energies around 400 MeV, this paper arbitrarily de nes the high energy tail as any proton with an energy above 400 MeV. In order to better understand the importance of accurately modeling the high energy tail for SPE spectra, the contribution to astronaut whole body e ective dose equivalent of the high energy portions of three di erent SPE models has been evaluated. To ensure completeness of this analysis, simple and complex geometries were used. This analysis showed that the high energy tail of certain SPEs can be relevant to astronaut exposure and hence safety. Therefore, models of high energy tails for SPEs should be well analyzed and based on data if possible.

Enhancing the efficiency of a three-lobe roots blower by means of by-passing gas to the working cavity through an ejector adaptor

NASA Astrophysics Data System (ADS)

Vizgalov, S. V.; Volkov, M. V.; Chekushkin, G. N.; Khisameev, I. G.

2017-08-01

A positive displacement Roots blower with two- or three-lobe straight-tooth or twisted rotors demonstrates high performance with small specific dimensions and is used to boost internal combustion engines, aerate tanks of treatment facilities, is employed in air and gas transport systems in the food, petrochemical and metallurgical industry. It is common knowledge that several solutions have been implemented in Roots blower designs with straight-tooth with three-lobe or more-lobes rotors. It is more practical to bypass a portion of the compressed gas to the working cavity of the blower through an ejector. The purpose of developing a mathematical model for a blower working in conjunction with an ejector adapter and the further research is to determine the efficiency of this scheme un-der different discharge pressure conditions and different ejector active flow temperatures (the gas cooling effect before the nozzle).

End region and current consolidation effects upon the performance of an MHD channel for the ETF conceptual design. [Engineering Test Facility

NASA Technical Reports Server (NTRS)

Wang, S. Y.; Smith, J. M.

1982-01-01

It is noted that operating conditions which yielded a peak thermodynamic efficiency (41%) for an EFT-size MHD/steam power plant were previously (Wang et al., 1981; Staiger, 1981) identified by considering only the active region (the primary portion for power production) of an MHD channel. These previous efforts are extended here to include an investigation of the effects of the channel end regions on overall power generation. Considering these effects, the peak plant thermodynamic efficiency is found to be slightly lowered (40.7%); the channel operating point for peak efficiency is shifted to the supersonic mode (Mach number of approximately 1.1) rather than the previous subsonic operation (Mach number of approximately 0.9). Also discussed is the sensitivity of the channel performance to the B-field, diffuser recovery coefficient, channel load parameter, Mach number, and combustor pressure.