Teaching Engineering Design in a Laboratory Setting

ERIC Educational Resources Information Center

Hummon, Norman P.; Bullen, A. G. R.

1974-01-01

Discusses the establishment of an environmental systems laboratory at the University of Pittsburgh with the support of the Sloan Foundation. Indicates that the "real world" can be brought into the laboratory by simulating on computers, software systems, and data bases. (CC)

Adsorption of Oxy-Anions in the Teaching Laboratory: An Experiment to Study a Fundamental Environmental Engineering Problem

ERIC Educational Resources Information Center

D'Arcy, Mitch; Bullough, Florence; Moffat, Chris; Borgomeo, Edoardo; Teh, Micheal; Vilar, Ramon; Weiss, Dominik J.

2014-01-01

Synthesizing and testing bicomposite adsorbents for the removal of environmentally problematic oxy-anions is high on the agenda of research-led universities. Here we present a laboratory module successfully developed at Imperial College London that introduces the advanced undergraduate student in engineering (chemical, civil, earth) and science…

A Pilot Study of the Effectiveness of Augmented Reality to Enhance the Use of Remote Labs in Electrical Engineering Education

ERIC Educational Resources Information Center

Borrero, A. Mejias; Marquez, J. M. Andujar

2012-01-01

Lab practices are an essential part of teaching in Engineering. However, traditional laboratory lessons developed in classroom labs (CL) must be adapted to teaching and learning strategies that go far beyond the common concept of e-learning, in the sense that completely virtualized distance education disconnects teachers and students from the real…

Safety leadership in the teaching laboratories of electrical and electronic engineering departments at Taiwanese Universities.

PubMed

Wu, Tsung-Chih

2008-01-01

Safety has always been one of the principal goals in teaching laboratories. Laboratories cannot serve their educational purpose when accidents occur. The leadership of department heads has a major impact on laboratory safety, so this study discusses the factors affecting safety leadership in teaching laboratories. This study uses a mail survey to explore the perceived safety leadership in electrical and electronic engineering departments at Taiwanese universities. An exploratory factor analysis shows that there are three main components of safety leadership, as measured on a safety leadership scale: safety controlling, safety coaching, and safety caring. The descriptive statistics also reveals that among faculty, the perception of department heads' safety leadership is in general positive. A two-way MANOVA shows that there are interaction effects on safety leadership between university size and instructor age; there are also interaction effects between presence of a safety committee and faculty gender and faculty age. It is therefore necessary to assess organizational factors when determining whether individual factors are the cause of differing perceptions among faculty members. The author also presents advice on improving safety leadership for department heads at small universities and at universities without safety committees.

Augmented Reality for the Improvement of Remote Laboratories: An Augmented Remote Laboratory

ERIC Educational Resources Information Center

Andujar, J. M.; Mejias, A.; Marquez, M. A.

2011-01-01

Augmented reality (AR) provides huge opportunities for online teaching in science and engineering, as these disciplines place emphasis on practical training and unsuited to completely nonclassroom training. This paper proposes a new concept in virtual and remote laboratories: the augmented remote laboratory (ARL). ARL is being tested in the first…

Development of Science and Mathematics Education System Including Teaching Experience of Students in Local Area

NASA Astrophysics Data System (ADS)

Kage, Hiroyuki

New reformation project on engineering education, which is supported from 2005 to 2008FY by Support Program for Contemporary Educational Needs of Ministry of Education, Culture, Sports, Science and Technology, started in Kyushu Institute of Technology. In this project, teaching experience of students is introduced into the curriculum of Faculty of Engineering. In the curriculum students try to prepare teaching materials and to teach local school pupils with them by themselves. Teaching experience is remarkably effective for them to strengthen their self-dependence and learning motivation. Science Education Center, Science Laboratory and Super Teachers College were also organized to promote the area cooperation on the education of science and mathematics.

Efficient Optoelectronics Teaching in Undergraduate Engineering Curriculum

ERIC Educational Resources Information Center

Matin, M. A.

2005-01-01

The Engineering Department's vision for undergraduate education for the next century is to develop a set of laboratory experiences that are thoughtfully sequenced and integrated to promote the full development of students in all courses. Optoelectronics is one of the most important and most demanding courses in Electrical and Computer Engineering.…

Teaching Process Engineering Principles Using an Ice Cream Maker

ERIC Educational Resources Information Center

Kaletunc, Gonul; Duemmel, Kevin; Gecik, Christopher

2007-01-01

The ice cream laboratory experiment is designed to illustrate and promote discussion of several engineering and science topics including material and energy balances, heat transfer, freezing, mass transfer, mixing, viscosity, and freezing point depression in a sophomore level engineering class. A pre-lab assignment requires the students to develop…

Brewing as a Comprehensive Learning Platform in Chemical Engineering

ERIC Educational Resources Information Center

Nielsen, Rudi P.; Sørensen, Jens L.; Simonsen, Morten E.; Madsen, Henrik T.; Muff, Jens; Strandgaard, Morten; Søgaard, Erik G.

2016-01-01

Chemical engineering is mostly taught using traditional classroom teaching and laboratory experiments when possible. Being a wide discipline encompassing topics such as analytical chemistry, process design, and microbiology, it may be argued that brewing of beer has many relations to chemical engineering topic-wise. This work illustrates how…

Developing a Remote Laboratory for Engineering Education

ERIC Educational Resources Information Center

Fabregas, E.; Farias, G.; Dormido-Canto, S.; Dormido, S.; Esquembre, F.

2011-01-01

New information technologies provide great opportunities for education. One such opportunity is the use of remote control laboratories for teaching students about control systems. This paper describes the creation of interactive remote laboratories (RLs). Two main software tools are used: Simulink and Easy Java Simulations (EJS). The first is a…

A Report of the Nuclear Engineering Division Sessions at the 1971 ASEE Annual Conference

ERIC Educational Resources Information Center

Eckley, Wayne; Nelson, George W.

1972-01-01

Summarizes the discussions at the conference under the topics, Objective Criteria for the Future" and Teaching Concepts Basic to Nuclear Engineering." Includes comments from personnel representing universities, industries, and government laboratories. (TS)

Facilitating Open-Ended Problem Solving: Training Engineering TAs To Facilitate Open-Ended Problem Solving.

ERIC Educational Resources Information Center

Streveler, Ruth A.; King, Robert H.

2000-01-01

Describes and evaluates a four-session training program for Multidisciplinary Engineering Laboratory (MEL) teaching assistants at the Colorado School of Mines. The sessions focus attention on student development approaches to learning. (EV)

45 CFR 680.11 - Staff involvement with NSF proposals and awards.

Code of Federal Regulations, 2010 CFR

2010-10-01

... teaching careers to spend a year or two at NSF and then return to research and teaching, usually at the... investigator and his or her laboratory or group (if any) in the same general field of science, engineering, or...

Bethune-Cookman University STEM Research Lab. DOE Renovation Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, Herbert W.

DOE funding was used to renovate 4,500 square feet of aging laboratories and classrooms that support science, engineering, and mathematics disciplines (specifically environmental science, and computer engineering). The expansion of the labs was needed to support robotics and environmental science research, and to better accommodate a wide variety of teaching situations. The renovated space includes a robotics laboratory, two multi-use labs, safe spaces for the storage of instrumentation, modern ventilation equipment, and other “smart” learning venues. The renovated areas feature technologies that are environmentally friendly with reduced energy costs. A campus showcase, the laboratories are a reflection of the University’smore » commitment to the environment and research as a tool for teaching. As anticipated, the labs facilitate the exploration of emerging technologies that are compatible with local and regional economic plans.« less

Teaching Sustainable Energy and Power Electronics to Engineering Students in a Laboratory Environment Using Industry-Standard Tools

ERIC Educational Resources Information Center

Ochs, David S.; Miller, Ruth Douglas

2015-01-01

Power electronics and renewable energy are two important topics for today's power engineering students. In many cases, the two topics are inextricably intertwined. As the renewable energy sector grows, the need for engineers qualified to design such systems grows as well. In order to train such engineers, new courses are needed that highlight the…

Biofilms as Biobarriers

ERIC Educational Resources Information Center

Lennox, John; Ashe, Jeffrey

2009-01-01

In a climate of increased concern for the environment and its protection, teachers in disciplines as diverse as biology, microbiology, environmental studies, and environmental engineering may be seeking teaching materials and laboratory exercises that will enable them to introduce these new concepts into their classrooms and laboratories. The…

Increasing Interest of Young Women in Engineering

ERIC Educational Resources Information Center

Hinterlong, Diane; Lawrence, Branson; DeVol, Purva

2014-01-01

The internationally recognized Illinois Mathematics and Science Academy (IMSA) develops creative, ethical leaders in science, technology, engineering and mathematics. As a teaching and learning laboratory created by the State of Illinois, IMSA enrolls academically talented Illinois students in grades 10 through 12 in its advanced, residential…

Biotechnology Apprenticeship for Secondary-Level Students: Teaching Advanced Cell Culture Techniques for Research.

ERIC Educational Resources Information Center

Lewis, Jennifer R.; Kotur, Mark S.; Butt, Omar; Kulcarni, Sumant; Riley, Alyssa A.; Ferrell, Nick; Sullivan, Kathryn D.; Ferrari, Mauro

2002-01-01

Discusses small-group apprenticeships (SGAs) as a method for introducing cell culture techniques to high school participants. Teaches cell culture practices and introduces advance imaging techniques to solve various biomedical engineering problems. Clarifies and illuminates the value of small-group laboratory apprenticeships. (Author/KHR)

Web Environment for Programming and Control of a Mobile Robot in a Remote Laboratory

ERIC Educational Resources Information Center

dos Santos Lopes, Maísa Soares; Gomes, Iago Pacheco; Trindade, Roque M. P.; da Silva, Alzira F.; de C. Lima, Antonio C.

2017-01-01

Remote robotics laboratories have been successfully used for engineering education. However, few of them use mobile robots to to teach computer science. This article describes a mobile robot Control and Programming Environment (CPE) and its pedagogical applications. The system comprises a remote laboratory for robotics, an online programming tool,…

Postgraduate Training in Student Learning and Teaching.

ERIC Educational Resources Information Center

Alpay, E.; Mendes-Tatsis, M. A.

2000-01-01

Presents an experiential postgraduate training program for student learning and supervision involving laboratory and pilot plant supervisions in the chemical engineering field. The program addresses some of the current concerns about non-technical training and the further development of the broad science and engineering knowledge of postgraduate…

Teaching smartphone and microcontroller systems using "Android Java"

NASA Astrophysics Data System (ADS)

Tigrek, Seyitriza

Mobile devices are becoming indispensable tools for many students and educators. Mobile technology is starting a new era in the computing methodologies in many engineering disciplines and laboratories. Microcontroller extension that communicates with mobile devices will take the data acquisition and control process into a new level in the sensing technology and communication. The purpose of this thesis is to develop a framework to incorporate the new mobile platform with robust embedded systems into the engineering curriculum. For this purpose a course material is developed "Introduction to Programming Java on a Mobile Platform" to teach novice programmers how to create applications, specifically on Android. Combining an introductory level programming class with the Android platform can appeal to non-programming individuals in multiple disciplines. The proposed course curriculum reduces the learning time, and allows senior engineering students to use the new framework for their specific needs in the labs such as mobile data acquisition and control projects. This work provides techniques for instructors with modest programming background to teach cutting edge technology, which is smartphone programming. Techniques developed in this work minimize unnecessary information carried into current teaching approaches with hands-on practice. It also helps the students with minimal background requirements overcome the barriers that have evolved around computer programming. The motivation of this thesis is to create a tailored programming introductory course to teach Java programming on Android by incorporating selected efficient methods from extant literature. The mechanism proposed in this thesis is to keep students motivated by an active approach based on student-centered learning with collaborative work. Teamwork through pair programming is adapted in this teaching process. Bloom's taxonomy, along with a knowledge survey, is used as a guide to classify the information and exercise problems. A prototype curriculum is a deliverable of this research that is suitable for novice programmers-such as engineering freshmen students. It also contains advanced material that allows senior students to use mobile phone and a microcontroller system to enhance engineering laboratories.

Virtually the Same: A Comparison of STEM Students' Content Knowledge, Course Performance, and Motivation to Learn in Virtual and Face-to-Face Introductory Biology Laboratories. Research and Teaching

ERIC Educational Resources Information Center

Reece, Amber J.; Butler, Malcolm B.

2017-01-01

Biology I is a required course for many science, technology, engineering, and mathematics (STEM) majors and is often their first college-level laboratory experience. The replacement of the traditional face-to-face laboratory experience with virtual laboratories could influence students' content knowledge, motivation to learn biology, and overall…

Mechatronics as a technological basis for an innovative learning environment in engineering

NASA Astrophysics Data System (ADS)

Garner, Gavin Thomas

Mechatronic systems that couple mechanical and electrical systems with the help of computer control are forcing a paradigm shift in the design, manufacture, and implementation of mechanical devices. The inherently interdisciplinary nature of these systems generates exciting new opportunities for developing a hands-on, inventive, and creativity-focused educational program while still embracing rigorous scientific fundamentals. The technologies associated with mechatronics are continually evolving (e.g., integrated circuit chips, miniature and new types of sensors, and state-of-the-art actuators). As a result, a mechatronics curriculum must prepare students to adapt along with these rapidly changing technologies---and perhaps even advance these technologies themselves. Such is the inspiring and uncharted new world that is presented for student exploration and experimentation in the University of Virginia's Mechatronics Laboratory. The underlying goal of this research has been to develop a framework for teaching mechatronics that helps students master fundamental concepts and build essential technical and analytical skills. To this end, two courses involving over fifty hours worth of technologically-innovative and educationally-effective laboratory experiments have been developed along with open-ended projects in response to the unique and new challenges associated with teaching mechatronics. These experiments synthesize an unprecedentedly vast array of skills from many different disciplines and enable students to haptically absorb the fundamental concepts involved in designing mechatronic systems. They have been optimized through several iterations to become highly efficient. Perspectives on the development of these courses and on the field of mechatronics in general are included. Furthermore, this dissertation demonstrates the integration of new technologies within a learning environment specifically designed to teach mechatronics to mechanical engineers. For mechanical engineering in particular, mechatronics poses considerable challenges, and necessitates a fundamental evolution in the understanding of the relationship between the various engineering disciplines. Consequently, this dissertation helps to define the role that mechatronics must play in mechanical engineering and presents unique laboratory experiments, creative projects, and modeling and simulation exercises as effective tools for teaching mechatronics to the modern mechanical engineering student.

Experiences Using an Open Source Software Library to Teach Computer Vision Subjects

ERIC Educational Resources Information Center

Cazorla, Miguel; Viejo, Diego

2015-01-01

Machine vision is an important subject in computer science and engineering degrees. For laboratory experimentation, it is desirable to have a complete and easy-to-use tool. In this work we present a Java library, oriented to teaching computer vision. We have designed and built the library from the scratch with emphasis on readability and…

Teaching Mass Transfer and Filtration Using Crossflow Reverse Osmosis and Nanofiltration: An Experiment for the Undergraduate Unit Operations Lab

ERIC Educational Resources Information Center

Anastasio, Daniel; McCutcheon, Jeffrey

2012-01-01

A crossflow reverse osmosis (RO) system was built for a senior-level chemical engineering unit operations laboratory course. Intended to teach students mass transfer fundamentals related to membrane separations, students tested several commercial desalination membranes, measuring water flux and salt rejections at various pressures, flow rates, and…

Integrating Sustainable Development in Chemical Engineering Education: The Application of an Environmental Management System

ERIC Educational Resources Information Center

Montanes, M. T.; Palomares, A. E.; Sanchez-Tovar, R.

2012-01-01

The principles of sustainable development have been integrated in chemical engineering education by means of an environmental management system. These principles have been introduced in the teaching laboratories where students perform their practical classes. In this paper, the implementation of the environmental management system, the problems…

Teaching Technical Writing in a Lab Course in Chemical Engineering

ERIC Educational Resources Information Center

Lombardo, Stephen J.

2010-01-01

Techniques are presented for improving the technical writing of chemical engineering students enrolled in an undergraduate laboratory course. The principles of writing covered are adopted from the book, Style: Lessons in Clarity and Grace, by Joseph M. Williams: General examples of writing are taken from this book and then are recast into examples…

Introducing Students to Structural Dynamics and Earthquake Engineering

ERIC Educational Resources Information Center

Anthoine, Armelle; Marazzi, Francesco; Tirelli, Daniel

2010-01-01

The European Laboratory for Structural Assessment (ELSA) is one of the world's main laboratories for seismic studies. Besides its research activities, it also aims to bring applied science closer to the public. This article describes teaching activities based on a demonstration shaking table which is used to introduce the structural dynamics of…

Virtual Laboratory for QoS Study in Next-Generation Networks with Metro Ethernet Access

ERIC Educational Resources Information Center

Gomez-Sacristan, Angel; Sempere-Paya, Victor M.; Rodriguez-Hernandez, Miguel A.

2016-01-01

Teaching in university engineering departments is currently facing a number of challenges, especially for those involved in the most innovative and dynamic areas of information and communication technology. Learning model developments that place greater weight on laboratory activities require investment in specific equipment that is often very…

A Network Steganography Lab on Detecting TCP/IP Covert Channels

ERIC Educational Resources Information Center

Zseby, Tanja; Vázquez, Félix Iglesias; Bernhardt, Valentin; Frkat, Davor; Annessi, Robert

2016-01-01

This paper presents a network security laboratory to teach data analysis for detecting TCP/IP covert channels. The laboratory is mainly designed for students of electrical engineering, but is open to students of other technical disciplines with similar background. Covert channels provide a method for leaking data from protected systems, which is a…

Requirements for Remote RF Laboratory Applications: An Educators' Perspective

ERIC Educational Resources Information Center

Cagiltay, N. E.; Aydin, E.; Oktem, R.; Kara, A.; Alexandru, M.; Reiner, B.

2009-01-01

This paper discusses the results of a study of the requirements for developing a remote RF laboratory. This study draws on the perspectives of educators in university electrical engineering departments and in technical colleges, on the teaching of the radio frequency (RF) domain. The study investigates how these educators would like the technical…

Development and Evaluation of Mechatronics Learning System in a Web-Based Environment

ERIC Educational Resources Information Center

Shyr, Wen-Jye

2011-01-01

The development of remote laboratory suitable for the reinforcement of undergraduate level teaching of mechatronics is important. For the reason, a Web-based mechatronics learning system, called the RECOLAB (REmote COntrol LABoratory), for remote learning in engineering education has been developed in this study. The web-based environment is an…

An Approach to Developing the Laboratory Through Senior Design Projects.

ERIC Educational Resources Information Center

Faghri, Amir

1987-01-01

Describes a program in which senior engineering students are given the opportunity to design, make, and test apparatus intended for an upper-level teaching laboratory. Discusses such projects as a vapor compressor test stand with refrigerant mass flow measurement, a double-walled concentric annular heat pipe, and a vacuum filling station. (TW)

Using a 400 kV Van de Graaff accelerator to teach physics at West Point

NASA Astrophysics Data System (ADS)

Marble, D. K.; Bruch, S. E.; Lainis, T.

1997-02-01

A small accelerator visitation laboratory is being built at the United States Military Academy using two 400 kV Van de Graaff accelerators. This laboratory will provide quality teaching experiments and increased research opportunities for both faculty and cadets as well as enhancing the department's ability to teach across the curriculum by using nuclear techniques to solve problems in environmental engineering, material science, archeology, art, etc. This training enhances a students ability to enter non-traditional fields that are becoming a large part of the physics job market. Furthermore, a small accelerator visitation laboratory for high school students can stimulate student interest in science and provide an effective means of communicating the scientific method to a general audience. A discussion of the USMA facility, class experiments and student research projects will be presented.

[Research-oriented experimental course of plant cell and gene engineering for undergraduates].

PubMed

Xiaofei, Lin; Rong, Zheng; Morigen, Morigen

2015-04-01

Research-oriented comprehensive experimental course for undergraduates is an important part for their training of innovation. We established an optional course of plant cell and gene engineering for undergraduates using our research platform. The course is designed to study the cellular and molecular basis and experimental techniques for plant tissue culture, isolation and culture of protoplast, genetic transformation, and screening and identification of transgenic plants. To develop undergraduates' ability in experimental design and operation, and inspire their interest in scientific research and innovation consciousness, we integrated experimental teaching and practice in plant genetic engineering on the tissue, cellular, and molecular levels. Students in the course practiced an experimental teaching model featured by two-week teaching of principles, independent experimental design and bench work, and ready-to-access laboratory. In this paper, we describe the contents, methods, evaluation system and a few issues to be solved in this course, as well as the general application and significance of the research-oriented experimental course in reforming undergraduates' teaching and training innovative talents.

National Educators' Workshop: Update 1991. Standard Experiments in Engineering Materials Science and Technology

NASA Technical Reports Server (NTRS)

Gardner, James E. (Compiler); Jacobs, James A. (Compiler); Stiegler, James O. (Compiler)

1992-01-01

Given here is a collection of experiments presented and demonstrated at the National Educators' Workshop: Update 91, held at the Oak Ridge National Laboratory on November 12-14, 1991. The experiments related to the nature and properties of engineering materials and provided information to assist in teaching about materials in the education community.

Laboratory: Undergraduate Laboratory Experiment Teaching Fundamental Concepts of Rheology in Context of Sickle Cell Anemia

ERIC Educational Resources Information Center

Vernengo, Jennifer; Purdy, Caitlin; Farrell, Stephanie

2014-01-01

This paper describes a biomedical engineering experiment that introduces students to rheology. Healthy and sickle-cell blood analogs are prepared that are composed of chitosan particles suspended in aqueous glycerol solutions, which substitute for RBCs and plasma, respectively. Students study flow properties of the blood analogs with a viscometer…

A Low-Cost Computer-Controlled Arduino-Based Educational Laboratory System for Teaching the Fundamentals of Photovoltaic Cells

ERIC Educational Resources Information Center

Zachariadou, K.; Yiasemides, K.; Trougkakos, N.

2012-01-01

We present a low-cost, fully computer-controlled, Arduino-based, educational laboratory (SolarInsight) to be used in undergraduate university courses concerned with electrical engineering and physics. The major goal of the system is to provide students with the necessary instrumentation, software tools and methodology in order to learn fundamental…

Smith college secondary math and science outreach program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Powell, J.A.; Clark, C.

1994-12-31

The Smith College Secondary Math and Science Outreach Program works collaboratively with front-line educators to encourage young women students of all abilities, especially underrepresented and underserved minorities, to continue studying math and science throughout high school. The program includes three main components: (1) Twenty-five to thirty teams of math/science teachers and guidance counselors participate in a year-long program which begins with a three-day Current Students/Future Scientists and Engineering Workshop. This event includes a keynote address, presentations and workshops by successful women in science and engineering, and hands-on laboratory sessions. Each participant receives a stipend and free room and board. Returningmore » to their schools, the teacher-counselor teams implement ongoing plans designed to counteract gender bias in the sciences and to alert female students to the broad range of math, science, and engineering career choices open to them. A follow-up session in the spring allows the teams to present and discuss their year-long activities. (2) TRI-ON, a day of science for 120 ninth- and tenth- grade girls from schools with a large underserved and underrepresented population, is held in early spring. Girls discover the excitement of laboratory investigation and interact with female college science and math majors. (3) Teaching Internships, initiated in 1991, involve ten to fifteen Smith College math and science majors in teaching in public schools. The teaching interns experience the rewards and challenges of classroom teaching, and they also serve as role models for younger students.« less

Electrophysiology for biomedical engineering students: a practical and theoretical course in animal electrocorticography.

PubMed

Albarracín, Ana L; Farfán, Fernando D; Coletti, Marcos A; Teruya, Pablo Y; Felice, Carmelo J

2016-09-01

The major challenge in laboratory teaching is the application of abstract concepts in simple and direct practical lessons. However, students rarely have the opportunity to participate in a laboratory that combines practical learning with a realistic research experience. In the Biomedical Engineering career, we offer short and optional courses to complement studies for students as they initiate their Graduation Project. The objective of these theoretical and practical courses is to introduce students to the topics of their projects. The present work describes an experience in electrophysiology to teach undergraduate students how to extract cortical information using electrocorticographic techniques. Students actively participate in some parts of the experience and then process and analyze the data obtained with different signal processing tools. In postlaboratory evaluations, students described the course as an exceptional opportunity for students interested in following a postgraduate science program and fully appreciated their contents. Copyright © 2016 The American Physiological Society.

Culturally Relevant Inquiry-Based Laboratory Module Implementations in Upper-Division Genetics and Cell Biology Teaching Laboratories

ERIC Educational Resources Information Center

Siritunga, Dimuth; Montero-Rojas, Maria; Carrero, Katherine; Toro, Gladys; Velez, Ana; Carrero-Martinez, Franklin A.

2011-01-01

Today, more minority students are entering undergraduate programs than ever before, but they earn only 6% of all science or engineering PhDs awarded in the United States. Many studies suggest that hands-on research activities enhance students' interest in pursuing a research career. In this paper, we present a model for the implementation of…

Adjustable Speed Drive Project for Teaching a Servo Systems Course Laboratory

ERIC Educational Resources Information Center

Rodriguez-Resendiz, J.; Herrera-Ruiz, G.; Rivas-Araiza, E. A.

2011-01-01

This paper describes an adjustable speed drive for a three-phase motor, which has been implemented as a design for a servo system laboratory course in an engineering curriculum. The platform is controlled and analyzed in a LabVIEW environment and run on a PC. Theory is introduced in order to show the sensorless algorithms. These are computed by…

Use of learning miniprojects in a chemistry laboratory for engineering

NASA Astrophysics Data System (ADS)

Cancela, Angeles; Maceiras, Rocio; Sánchez, Angel; Izquierdo, Milagros; Urréjola, Santiago

2016-01-01

The aim of this paper is to describe the design of chemical engineering laboratory sessions in order to focus them on the learning company approach. This is an activity carried out in the classroom similar to the activities that exist in real companies. This could lead classroom practice to a more cooperative learning and a different style of experimentation. The stated goal is to make a design that seeks to motivate students in a cooperative manner to perform their experiments self-directed and self-organised. The teaching organisation and development of participatory action research are described.

[From gene cloning to expressional analysis--practice and experience from educational reform of experimental gene engineering].

PubMed

Wu, Yan-Hua; Guo, Bin; Lou, Hui-Ling; Cui, Yu-Liang; Gu, Hui-Juan; Qiao, Shou-Yi

2012-02-01

Experimental gene engineering is a laboratory course focusing on the molecular structure, expression pattern and biological function of genes. Providing our students with a solid knowledge base and correct ways to conduct research is very important for high-quality education of genetic engineering. Inspired by recent progresses in this field, we improved the experimental gene engineering course by adding more updated knowledge and technologies and emphasizing on the combination of teaching and research, with the aim of offering our students a good start in their scientific careers.

Improving consistency in large laboratory courses: a design for a standardized practical exam.

PubMed

Chen, Xinnian; Graesser, Donnasue; Sah, Megha

2015-06-01

Laboratory courses serve as important gateways to science, technology, engineering, and mathematics education. One of the challenges in assessing laboratory learning is to conduct meaningful and standardized practical exams, especially for large multisection laboratory courses. Laboratory practical exams in life sciences courses are frequently administered by asking students to move from station to station to answer questions, apply knowledge gained during laboratory experiments, interpret data, and identify various tissues and organs using various microscopic and gross specimens. This approach puts a stringent time limit on all questions regardless of the level of difficulty and also invariably increases the potential risk of cheating. To avoid potential cheating in laboratory courses with multiple sections, the setup for practical exams is often changed in some way between sections. In laboratory courses with multiple instructors or teaching assistants, practical exams may be handled inconsistently among different laboratory sections, due to differences in background knowledge, perceptions of the laboratory goals, or prior teaching experience. In this article, we describe a design for a laboratory practical exam that aims to align the assessment questions with well-defined laboratory learning objectives and improve the consistency among all laboratory sections. Copyright © 2015 The American Physiological Society.

A Pilot Study of the Effectiveness of Augmented Reality to Enhance the Use of Remote Labs in Electrical Engineering Education

NASA Astrophysics Data System (ADS)

Mejías Borrero, A.; Andújar Márquez, J. M.

2012-10-01

Lab practices are an essential part of teaching in Engineering. However, traditional laboratory lessons developed in classroom labs (CL) must be adapted to teaching and learning strategies that go far beyond the common concept of e-learning, in the sense that completely virtualized distance education disconnects teachers and students from the real world, which can generate specific problems in laboratory classes. Current proposals of virtual labs (VL) and remote labs (RL) do not either cover new needs properly or contribute remarkable improvement to traditional labs—except that they favor distance training. Therefore, online teaching and learning in lab practices demand a further step beyond current VL and RL. This paper poses a new reality and new teaching/learning concepts in the field of lab practices in engineering. The developed augmented reality-based lab system (augmented remote lab, ARL) enables teachers and students to work remotely (Internet/intranet) in current CL, including virtual elements which interact with real ones. An educational experience was conducted to assess the developed ARL with the participation of a group of 10 teachers and another group of 20 students. Both groups have completed lab practices of the contents in the subjects Digital Systems and Robotics and Industrial Automation, which belong to the second year of the new degree in Electronic Engineering (adapted to the European Space for Higher Education). The labs were carried out by means of three different possibilities: CL, VL and ARL. After completion, both groups were asked to fill in some questionnaires aimed at measuring the improvement contributed by ARL relative to CL and VL. Except in some specific questions, the opinion of teachers and students was rather similar and positive regarding the use and possibilities of ARL. Although the results are still preliminary and need further study, seems to conclude that ARL remarkably improves the possibilities of current VL and RL. Furthermore, ARL can be concluded to allow further possibilities when used online than traditional laboratory lessons completed in CL.

2D and 3D virtual interactive laboratories of physics on Unity platform

NASA Astrophysics Data System (ADS)

González, J. D.; Escobar, J. H.; Sánchez, H.; De la Hoz, J.; Beltrán, J. R.

2017-12-01

Using the cross-platform game engine Unity, we develop virtual laboratories for PC, consoles, mobile devices and website as an innovative tool to study physics. There is extensive uptake of ICT in the teaching of science and its impact on the learning, and considering the limited availability of laboratories for physics teaching and the difficulties this causes in the learning of school students, we design the virtual laboratories to enhance studentâĂŹs knowledge of concepts in physics. To achieve this goal, we use Unity due to provide support bump mapping, reflection mapping, parallax mapping, dynamics shadows using shadows maps, full-screen post-processing effects and render-to-texture. Unity can use the best variant for the current video hardware and, if none are compatible, to use an alternative shader that may sacrifice features for performance. The control over delivery to mobile devices, web browsers, consoles and desktops is the main reason Unity is the best option among the same kind cross-platform. Supported platforms include Android, Apple TV, Linux, iOS, Nintendo 3DS line, macOS, PlayStation 4, Windows Phone 8, Wii but also an asset server and Nvidia’s PhysX physics engine which is the most relevant tool on Unity for our PhysLab.

Computer-Based Mathematics Instructions for Engineering Students

NASA Technical Reports Server (NTRS)

Khan, Mustaq A.; Wall, Curtiss E.

1996-01-01

Almost every engineering course involves mathematics in one form or another. The analytical process of developing mathematical models is very important for engineering students. However, the computational process involved in the solution of some mathematical problems may be very tedious and time consuming. There is a significant amount of mathematical software such as Mathematica, Mathcad, and Maple designed to aid in the solution of these instructional problems. The use of these packages in classroom teaching can greatly enhance understanding, and save time. Integration of computer technology in mathematics classes, without de-emphasizing the traditional analytical aspects of teaching, has proven very successful and is becoming almost essential. Sample computer laboratory modules are developed for presentation in the classroom setting. This is accomplished through the use of overhead projectors linked to graphing calculators and computers. Model problems are carefully selected from different areas.

Virtual experiments in electronics: beyond logistics, budgets, and the art of the possible

NASA Astrophysics Data System (ADS)

Chapman, Brian

1999-09-01

It is common and correct to suppose that computers support flexible delivery of educational resources by offering virtual experiments that replicate and substitute for experiments traditionally offered in conventional teaching laboratories. However, traditional methods are limited by logistics, costs, and what is physically possible to accomplish on a laboratory bench. Virtual experiments allow experimental approaches to teaching and learning to transcend these limits. This paper analyses recent and current developments in educational software for 1st- year physics, 2nd-year electronics engineering and 3rd-year communication engineering, based on three criteria: (1)Is the virtual experiment possible in a real laboratory? (2)How direct is the link between the experimental manipulation and the reinforcement of theoretical learning? (3) What impact might the virtual experiment have on the learner's acquisition of practical measurement skills? Virtual experiments allow more flexibility in the directness of the link between experimental manipulation and the theoretical message. However, increasing the directness of this link may reduce or even abolish the measurement processes associated with traditional experiments. Virtual experiments thus pose educational challenges: (a) expanding the design of experimentally based curricula beyond traditional boundaries and (b) ensuring that the learner acquires sufficient experience in making practical measurements.

A curriculum for real-time computer and control systems engineering

NASA Technical Reports Server (NTRS)

Halang, Wolfgang A.

1990-01-01

An outline of a syllabus for the education of real-time-systems engineers is given. This comprises the treatment of basic concepts, real-time software engineering, and programming in high-level real-time languages, real-time operating systems with special emphasis on such topics as task scheduling, hardware architectures, and especially distributed automation structures, process interfacing, system reliability and fault-tolerance, and integrated project development support systems. Accompanying course material and laboratory work are outlined, and suggestions for establishing a laboratory with advanced, but low-cost, hardware and software are provided. How the curriculum can be extended into a second semester is discussed, and areas for possible graduate research are listed. The suitable selection of a high-level real-time language and supporting operating system for teaching purposes is considered.

Evolution of the teachings of chemistry in the new degrees of School of Agricultural Engineering and its importance in the acquisition of competencies

NASA Astrophysics Data System (ADS)

Arce, Augusto; Tarquis, Ana M.; Castellanos, Maria Teresa; Requejo, Maria Isabel; Cartagena, Maria Carmen

2014-05-01

The academic year 2012-13 is the third year of implementation of the Bologna process in ETSI Agricultural for the subjects Chemistry I and Chemistry II in the new four Degrees: Graduate in Engineering and Agricultural Science, Food Engineering Graduate, Graduate in Engineering Environmental and Biotechnology graduate. We have implemented new interactive methodologies in the teaching-learning process based on the use of the virtual platform of the UPM, and teaching support materials and new laboratory practice developing has. It has also launched new continuous assessment systems that promote active student participation. A comparative study of academic achievements by students of the new grades in the subjects of chemistry during the last three academic years was performed to correlating the results obtained, the success rate and the drop out, and compare with the level of prior knowledge to those entering students. Possible solutions to try and fix these results in future courses are proposed Finally, the general competencies that contribute this course, how they are acquired and how they should be evaluated correctly are indicated. Acknowledgments: Innovation educative projects Nº IE02054-11/12 UPM. 2012

Switching gears and changing lanes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammock, Earlene C.

2002-01-01

From musing over Shakespeare's fine lines and metaphors to teaching technical writing and editing, and finally, to cranking out scientific and technical documents, writing articles, and editing publications-how'd a nice girl like me end up in a place like this? Twice, after having prepared for an academic career of teaching and research, I found myself in a technical communications position-first, at the University of Texas at El Paso College of Engineering and later, at Los Alamos National Laboratory. What happened?

Three-Dimensional Printing of Human Skeletal Muscle Cells: An Interdisciplinary Approach for Studying Biological Systems

ERIC Educational Resources Information Center

Bagley, James R.; Galpin, Andrew J.

2015-01-01

Interdisciplinary exploration is vital to education in the 21st century. This manuscript outlines an innovative laboratory-based teaching method that combines elements of biochemistry/molecular biology, kinesiology/health science, computer science, and manufacturing engineering to give students the ability to better conceptualize complex…

Teaching Smartphone and Microcontroller Systems Using "Android Java"

ERIC Educational Resources Information Center

Tigrek, Seyitriza

2012-01-01

Mobile devices are becoming indispensable tools for many students and educators. Mobile technology is starting a new era in the computing methodologies in many engineering disciplines and laboratories. Microcontroller extension that communicates with mobile devices will take the data acquisition and control process into a new level in the sensing…

Learning, Teaching and Scholarship: Fundamental Tensions of Undergraduate Research

ERIC Educational Resources Information Center

Laursen, Sandra; Seymour, Elaine; Hunter, Anne-Barrie

2012-01-01

Each year, thousands of undergraduates in the science, technology, engineering, and mathematics (STEM) fields conduct research in US university and college laboratories. Such undergraduate research (UR) experiences are common practice in US higher education, with nearly a century of history at research universities and liberal arts colleges.…

A Modern and Interactive Approach to Learning Laser and Optical Communications.

ERIC Educational Resources Information Center

Minasian, Robert; Alameh, Kamal

2002-01-01

Discusses challenges in teaching lasers and optical communications to engineers, including the prohibitive cost of laboratory experiments, and describes the development of a computer-based photonics simulation experiment module which provides students with an understanding and visualization of how lasers can be modulated in telecommunications.…

Research Institute for Technical Careers

NASA Technical Reports Server (NTRS)

Glenn, Ronald L.

1996-01-01

The NASA research grant to Wilberforce University enabled us to establish the Research Institute for Technical Careers (RITC) in order to improve the teaching of science and engineering at Wilberforce. The major components of the research grant are infrastructure development, establishment of the Wilberforce Intensive Summer Experience (WISE), and Joint Research Collaborations with NASA Scientists. (A) Infrastructure Development. The NASA grant has enabled us to improve the standard of our chemistry laboratory and establish the electronics, design, and robotics laboratories. These laboratories have significantly improved the level of instruction at Wilberforce University. (B) Wilberforce Intensive Summer Experience (WISE). The WISE program is a science and engineering bridge program for prefreshman students. It is an intensive academic experience designed to strengthen students' knowledge in mathematics, science, engineering, computing skills, and writing. (C) Joint Collaboration. Another feature of the grant is research collaborations between NASA Scientists and Wilberforce University Scientists. These collaborations have enabled our faculty and students to conduct research at NASA Lewis during the summer and publish research findings in various journals and scientific proceedings.

Final report to DOE: Matching Grant Program for the Penn State University Nuclear Engineering Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jack S. Brenizer, Jr.

2003-01-17

The DOE/Industry Matching Grant Program is designed to encourage collaborative support for nuclear engineering education as well as research between the nation's nuclear industry and the U.S. Department of Energy (DOE). Despite a serious decline in student enrollments in the 1980s and 1990s, the discipline of nuclear engineering remained important to the advancement of the mission goals of DOE. The program is designed to ensure that academic programs in nuclear engineering are maintained and enhanced in universities throughout the U.S. At Penn State, the Matching Grant Program played a critical role in the survival of the Nuclear Engineering degree programs.more » Funds were used in a variety of ways to support both undergraduate and graduate students directly. Some of these included providing seed funding for new graduate research initiatives, funding the development of new course materials, supporting new teaching facilities, maintenance and purchase of teaching laboratory equipment, and providing undergraduate scholarships, graduate fellowships, and wage payroll positions for students.« less

New teaching methods in use at UC Irvine's optical engineering and instrument design programs

NASA Astrophysics Data System (ADS)

Silberman, Donn M.; Rowe, T. Scott; Jo, Joshua; Dimas, David

2012-10-01

New teaching methods reach geographically dispersed students with advances in Distance Education. Capabilities include a new "Hybrid" teaching method with an instructor in a classroom and a live WebEx simulcast for remote students. Our Distance Education Geometric and Physical Optics courses include Hands-On Optics experiments. Low cost laboratory kits have been developed and YouTube type video recordings of the instructor using these tools guide the students through their labs. A weekly "Office Hour" has been developed using WebEx and a Live Webcam the instructor uses to display his live writings from his notebook for answering students' questions.

Continuous-Grouped-Self-Learning: In the Perspective of Lecturers, Tutors and Laboratory Instructors

ERIC Educational Resources Information Center

Azau, Mohd Azrin Mohd; Yao, Low Ming; Aik, Goo Soon; Yeong, Chin Kock; Nor, Mohamad Nizam; Abdullah, Ahmad Yusri; Jamil, Mohd Hafidz Mohamad; Yahya, Nasiruddin; Abas, Ahmad Fauzi; Saripan, M. Iqbal

2009-01-01

This paper presents the perception of lecturers, tutors and lab instructors towards the implemented Continuous-Group-Self-Learning (CGSL) in the Department of Computer and Communication System Engineering (CCSE), Universiti Putra Malaysia. This innovative system introduces mock teaching and student-lecturer role as a technique of delivery. The…

QUEST: An Assessment Tool for Web-Based Learning.

ERIC Educational Resources Information Center

Choren, Ricardo; Blois, Marcelo; Fuks, Hugo

In 1997, the Software Engineering Laboratory at Pontifical Catholic University of Rio de Janeiro (Brazil) implemented the first version of AulaNet (TM) a World Wide Web-based educational environment. Some of the teaching staff will use this environment in 1998 to offer regular term disciplines through the Web. This paper introduces Quest, a tool…

Course Manual for X-Ray Measurements (GS-462).

ERIC Educational Resources Information Center

Oregon State Univ., Corvallis. Dept. of General Science.

This is the second of three sequential course manuals for instructors in X-Ray science and engineering developed at Oregon State University. It consists of outlines for fourteen lectures and eight laboratory exercises with problems and two examinations. Also included is a list of references, equipment, and materials. The purposes, teaching aids,…

Teaching Problem Solving: Don't Forget the Problem Solver(s)

ERIC Educational Resources Information Center

Ranade, Saidas M.; Corrales, Angela

2013-01-01

The importance of intrapersonal and interpersonal intelligences has long been known but educators have debated whether to and how to incorporate those topics in an already crowded engineering curriculum. In 2010, the authors used the classroom as a laboratory to observe the usefulness of including selected case studies and exercises from the…

National Educators' Workshop: Update 1996

NASA Technical Reports Server (NTRS)

Gardner, James E.; Freeman, Ginger L.; Jacobs, James; Parkin, Don M.

1997-01-01

This document contains a collection of experiments presented and demonstrated at the National Educators' Workshop: Update 96, held at Los Alamos National Laboratory, Los Alamos, New Mexico on October 27-30, 1996. The experiments related to the nature and properties of engineering materials and provided information to assist in teaching about materials in the education community.

Lab Manual & Resources for Materials Science, Engineering and Technology on CD-Rom

NASA Technical Reports Server (NTRS)

Jacobs, James A.; McKenney, Alfred E.

2001-01-01

The National Educators' Workshop (NEW:Update) series of workshops has been in existence since 1986. These annual workshops focus on technical updates and laboratory experiments for materials science, engineering and technology, involving new and traditional content in the field. Scores of educators and industrial and national laboratory personnel have contributed many useful experiments and demonstrations which were then published as NASA Conference Proceedings. This "out poring of riches" creates an ever-expanding shelf of valuable teaching tools for college, university, community college and advanced high school instruction. Now, more than 400 experiments and demonstrations, representing the first thirteen years of NEW:Updates have been selected and published on a CD-ROM, through the collaboration of this national network of materials educators, engineers, and scientists. The CD-ROM examined in this document utilizes the popular Adobe Acrobat Reader format and operates on most popular computer platforms. This presentation provides an overview of the second edition of Experiments in Materials Science, Engineering and Technology (EMSET2) CD-ROM, ISBN 0-13-030534-0.

The eminent need for an academic program in universities to teach nanomedicine.

PubMed

Vélez, Juan Manuel; Vélez, Juan Jesus

2011-01-01

Nanomedicine is on the cutting edge of technology applied to medical and biological sciences. Nanodevices, nanomaterials, nanoinstruments, nanotechnologies, and nanotechniques (laboratory methods and procedures) are important for the modern practice of medicine and essential for research that could stimulate the discovery of new medical advances. Accordingly, there is an eminent need for implementing an academic program in universities to teach this indispensable and pragmatic discipline, especially in the departments of graduate studies and research in the areas of pharmacology, genetic engineering, proteomics, and molecular and cellular biology.

A Survey and Evaluation of Simulators Suitable for Teaching Courses in Computer Architecture and Organization

ERIC Educational Resources Information Center

Nikolic, B.; Radivojevic, Z.; Djordjevic, J.; Milutinovic, V.

2009-01-01

Courses in Computer Architecture and Organization are regularly included in Computer Engineering curricula. These courses are usually organized in such a way that students obtain not only a purely theoretical experience, but also a practical understanding of the topics lectured. This practical work is usually done in a laboratory using simulators…

The 18 mm[superscript 2] Laboratory: Teaching MEMS Development with the SUMMiT Foundry Process

ERIC Educational Resources Information Center

Dallas, T.; Berg, J. M.; Gale, R. O.

2012-01-01

This paper describes the goals, pedagogical system, and educational outcomes of a three-semester curriculum in microelectromechanical systems (MEMS). The sequence takes engineering students with no formal MEMS training and gives them the skills to participate in cutting-edge MEMS research and development. The evolution of the curriculum from…

The Robert E. Hopkins Center for Optical Design and Engineering

NASA Astrophysics Data System (ADS)

Zavislan, James M.; Brown, Thomas G.

2008-08-01

In 1929, a grant from Eastman Kodak and Bausch and Lomb established The Institute of Optics as the nation's first academic institution devoted to training optical scientists and engineers. The mission was 'to study light in all its phases', and the curriculum was designed to educate students in the fundamentals of optical science and build essential skills in applied optics and optical engineering. Indeed, our historic strength has been a balance between optical science and engineering--we have alumni who are carrying out prize-winning research in optical physics, alumni who are innovative optical engineers, and still other alumni who are leaders in the business community. Faculty who are top-notch optical engineers are an important resource to optical physics research groups -- likewise, teaching and modeling excellent optical science provides a strong underpinning for students on the applied/engineering end of the spectrum. This model -an undergraduate and graduate program that balances fundamental optics, applied optics, and optical engineering- has served us well. The impressive and diverse range of opportunities for our BS graduates has withstood economic cycles, and the students graduate with a healthy dose of practical experience. Undergraduate advisors, with considerable initiative from the program coordinator, are very aggressive in pointing students toward summer research and engineering opportunities. The vast majority of our undergraduate students graduate with at least one summer of experience in a company or a research laboratory. For example, 95% of the class of 2008 spent the summer of 2007 at companies and/or research laboratories: These include Zygo, NRL, Bausch and Lomb, The University of Rochester(The Institute of Optics, Medical Center, and Laboratory for Laser Energetics), QED, ARL Night Vision laboratories, JPL, Kollsman, OptiMax, Northrup Grumman, and at least two other companies. It is an impressive list, and bodes well for the career preparation for these students. While this extracurricular experience is truly world-class, an integrated design experience defined within our academic program is increasingly necessary for those going on to professional careers in engineering. This paper describes the philosophy behind a revision to our undergraduate curriculum that integrates a design experience and describes the engineering laboratory that has been established to make it a reality. The laboratory and design center has been named in honor of Robert E. Hopkins, former director and professor, co-founder of Tropel corporation, and a lifelong devotee to engineering innovation.

Biotechnology Apprenticeship for Secondary-Level Students: Teaching Advanced Cell Culture Techniques for Research

PubMed Central

Lewis, Jennifer R.; Kotur, Mark S.; Butt, Omar; Kulcarni, Sumant; Riley, Alyssa A.; Ferrell, Nick; Sullivan, Kathryn D.; Ferrari, Mauro

2002-01-01

The purpose of this article is to discuss small-group apprenticeships (SGAs) as a method to instruct cell culture techniques to high school participants. The study aimed to teach cell culture practices and to introduce advanced imaging techniques to solve various biomedical engineering problems. Participants designed and completed experiments using both flow cytometry and laser scanning cytometry during the 1-month summer apprenticeship. In addition to effectively and efficiently teaching cell biology laboratory techniques, this course design provided an opportunity for research training, career exploration, and mentoring. Students participated in active research projects, working with a skilled interdisciplinary team of researchers in a large research institution with access to state-of-the-art instrumentation. The instructors, composed of graduate students, laboratory managers, and principal investigators, worked well together to present a real and worthwhile research experience. The students enjoyed learning cell culture techniques while contributing to active research projects. The institution's researchers were equally enthusiastic to instruct and serve as mentors. In this article, we clarify and illuminate the value of small-group laboratory apprenticeships to the institution and the students by presenting the results and experiences of seven middle and high school participants and their instructors. PMID:12587031

Biotechnology apprenticeship for secondary-level students: teaching advanced cell culture techniques for research.

PubMed

Lewis, Jennifer R; Kotur, Mark S; Butt, Omar; Kulcarni, Sumant; Riley, Alyssa A; Ferrell, Nick; Sullivan, Kathryn D; Ferrari, Mauro

2002-01-01

The purpose of this article is to discuss small-group apprenticeships (SGAs) as a method to instruct cell culture techniques to high school participants. The study aimed to teach cell culture practices and to introduce advanced imaging techniques to solve various biomedical engineering problems. Participants designed and completed experiments using both flow cytometry and laser scanning cytometry during the 1-month summer apprenticeship. In addition to effectively and efficiently teaching cell biology laboratory techniques, this course design provided an opportunity for research training, career exploration, and mentoring. Students participated in active research projects, working with a skilled interdisciplinary team of researchers in a large research institution with access to state-of-the-art instrumentation. The instructors, composed of graduate students, laboratory managers, and principal investigators, worked well together to present a real and worthwhile research experience. The students enjoyed learning cell culture techniques while contributing to active research projects. The institution's researchers were equally enthusiastic to instruct and serve as mentors. In this article, we clarify and illuminate the value of small-group laboratory apprenticeships to the institution and the students by presenting the results and experiences of seven middle and high school participants and their instructors.

Analyzing the Effect of Technology-Based Intervention in Language Laboratory to Improve Listening Skills of First Year Engineering Students (El uso de la tecnología en el laboratorio de idiomas para el mejoramiento de las habilidades de escucha de estudiantes de ingeniería de primer año)

ERIC Educational Resources Information Center

Pasupathi, Madhumathi

2013-01-01

First year students pursuing engineering education face problems with their listening skills. Most of the Indian schools use a bilingual method for teaching subjects from primary school through high school. Nonetheless, students entering university education develop anxiety in listening to classroom lectures in English. This article reports an…

Effective approach to spectroscopy and spectral analysis techniques using Matlab

NASA Astrophysics Data System (ADS)

Li, Xiang; Lv, Yong

2017-08-01

With the development of electronic information, computer and network, modern education technology has entered new era, which would give a great impact on teaching process. Spectroscopy and spectral analysis is an elective course for Optoelectronic Information Science and engineering. The teaching objective of this course is to master the basic concepts and principles of spectroscopy, spectral analysis and testing of basic technical means. Then, let the students learn the principle and technology of the spectrum to study the structure and state of the material and the developing process of the technology. MATLAB (matrix laboratory) is a multi-paradigm numerical computing environment and fourth-generation programming language. A proprietary programming language developed by MathWorks, MATLAB allows matrix manipulations, plotting of functions and data, Based on the teaching practice, this paper summarizes the new situation of applying Matlab to the teaching of spectroscopy. This would be suitable for most of the current school multimedia assisted teaching

A pH Sensor Based on a Stainless Steel Electrode Electrodeposited with Iridium Oxide

ERIC Educational Resources Information Center

Martinez, C. C. M.; Madrid, R. E.; Felice, C. J.

2009-01-01

A simple procedure to make an iridium oxide (IrO[subscript 2]) electrodeposited pH sensor, that can be used in a chemical, biomedical, or materials laboratory, is presented here. Some exercises, based on this sensor, that can be used to teach important concepts in the field of biomedical, biochemical, tissue, or materials engineering, are also…

Structures and Systems. Grade 11-12. Course #8155 (Semester). Technology Education Course Guide. Industrial Arts/Technology Education.

ERIC Educational Resources Information Center

North Carolina State Dept. of Public Instruction, Raleigh. Div. of Vocational Education.

This guide is intended for use in teaching a course to broaden students' appreciation and understanding of constructed items and the construction process. The course focuses on the steps that are taken after the design and engineering phase has been completed. Laboratory assignments allow students to explore the technical processes involved in the…

Implementation and Assessment of a Virtual Laboratory of Parallel Robots Developed for Engineering Students

ERIC Educational Resources Information Center

Gil, Arturo; Peidró, Adrián; Reinoso, Óscar; Marín, José María

2017-01-01

This paper presents a tool, LABEL, oriented to the teaching of parallel robotics. The application, organized as a set of tools developed using Easy Java Simulations, enables the study of the kinematics of parallel robotics. A set of classical parallel structures was implemented such that LABEL can solve the inverse and direct kinematic problem of…

Develop virtual joint laboratory for education like distance engineering system for robotic applications

NASA Astrophysics Data System (ADS)

Latinovic, T. S.; Deaconu, S. I.; Latinović, M. T.; Malešević, N.; Barz, C.

2015-06-01

This paper work with a new system that provides distance learning and online training engineers. The purpose of this paper is to develop and provide web-based system for the handling and control of remote devices via the Internet. Remote devices are currently the industry or mobile robots [13]. For future product development machine in the factory will be included in the system. This article also discusses the current use of virtual reality tools in the fields of science and engineering education. One programming tool in particular, virtual reality modeling language (VRML) is presented in the light of its applications and capabilities in the development of computer visualization tool for education. One contribution of this paper is to present the software tools and examples that can encourage educators to develop a virtual reality model to improve teaching in their discipline. [12] This paper aims to introduce a software platform, called VALIP where users can build, share, and manipulate 3D content in cooperation with the interaction processes in a 3D context, while participating hardware and software devices can be physical and / or logical distributed and connected together via the Internet. VALIP the integration of virtual laboratories to appropriate partners; therefore, allowing access to all laboratories in any of the partners in the project. VALIP provides advanced laboratory for training and research within robotics and production engineering, and thus, provides a great laboratory facilities with only having to invest a limited amount of resources at the local level to the partner site.

Teaching and Research with Accelerators at Tarleton State University

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marble, Daniel K.

2009-03-10

Tarleton State University students began performing both research and laboratory experiments using accelerators in 1998 through visitation programs at the University of North Texas, US Army Research Laboratory, and the Naval Surface Warfare Center at Carderock. In 2003, Tarleton outfitted its new science building with a 1 MV pelletron that was donated by the California Institution of Technology. The accelerator has been upgraded and supports a wide range of classes for both the Physics program and the ABET accredited Engineering Physics program as well as supplying undergraduate research opportunities on campus. A discussion of various laboratory activities and research projectsmore » performed by Tarleton students will be presented.« less

Culturally relevant inquiry-based laboratory module implementations in upper-division genetics and cell biology teaching laboratories.

PubMed

Siritunga, Dimuth; Montero-Rojas, María; Carrero, Katherine; Toro, Gladys; Vélez, Ana; Carrero-Martínez, Franklin A

2011-01-01

Today, more minority students are entering undergraduate programs than ever before, but they earn only 6% of all science or engineering PhDs awarded in the United States. Many studies suggest that hands-on research activities enhance students' interest in pursuing a research career. In this paper, we present a model for the implementation of laboratory research in the undergraduate teaching laboratory using a culturally relevant approach to engage students. Laboratory modules were implemented in upper-division genetics and cell biology courses using cassava as the central theme. Students were asked to bring cassava samples from their respective towns, which allowed them to compare their field-collected samples against known lineages from agricultural stations at the end of the implementation. Assessment of content and learning perceptions revealed that our novel approach allowed students to learn while engaged in characterizing Puerto Rican cassava. In two semesters, based on the percentage of students who answered correctly in the premodule assessment for content knowledge, there was an overall improvement of 66% and 55% at the end in the genetics course and 24% and 15% in the cell biology course. Our proposed pedagogical model enhances students' professional competitiveness by providing students with valuable research skills as they work on a problem to which they can relate.

Culturally Relevant Inquiry-Based Laboratory Module Implementations in Upper-Division Genetics and Cell Biology Teaching Laboratories

PubMed Central

Siritunga, Dimuth; Montero-Rojas, María; Carrero, Katherine; Toro, Gladys; Vélez, Ana; Carrero-Martínez, Franklin A.

2011-01-01

Today, more minority students are entering undergraduate programs than ever before, but they earn only 6% of all science or engineering PhDs awarded in the United States. Many studies suggest that hands-on research activities enhance students’ interest in pursuing a research career. In this paper, we present a model for the implementation of laboratory research in the undergraduate teaching laboratory using a culturally relevant approach to engage students. Laboratory modules were implemented in upper-division genetics and cell biology courses using cassava as the central theme. Students were asked to bring cassava samples from their respective towns, which allowed them to compare their field-collected samples against known lineages from agricultural stations at the end of the implementation. Assessment of content and learning perceptions revealed that our novel approach allowed students to learn while engaged in characterizing Puerto Rican cassava. In two semesters, based on the percentage of students who answered correctly in the premodule assessment for content knowledge, there was an overall improvement of 66% and 55% at the end in the genetics course and 24% and 15% in the cell biology course. Our proposed pedagogical model enhances students’ professional competitiveness by providing students with valuable research skills as they work on a problem to which they can relate. PMID:21885825

Shedding light on the subject: introduction to illumination engineering and design for multidiscipline engineering students

NASA Astrophysics Data System (ADS)

Ronen, Ram S.; Smith, R. Frank

1995-10-01

Educating engineers and architects in Illumination Engineering and related subjects has become a very important field and a very satisfying and rewarding one. Main reasons include the need to significantly conserve lighting energy and meet government regulations while supplying appropriate light levels and achieving aesthetical requirements. The proliferation of new lamps, luminaries and lighting controllers many of which are 'energy savers' also helps a trend to seek help from lighting engineers when designing new commercial and residential buildings. That trend is believed to continue and grow as benefits become attractive and new government conservation regulations take affect. To make things even better one notices that Engineering and Science students in most disciplines make excellent candidates for Illumination Engineers because of their background and teaching them can move ahead at a brisk pace and be a rewarding experience nevertheless. In the past two years, Cal Poly Pomona College of Engineering has been the beneficiary of a DOE/California grant. Its purpose was to precipitate and oversee light curricula in various California community colleges and also develop and launch an Illumination Engineering minor at Cal Poly University. Both objectives have successfully been met. Numerous community colleges throughout California developed and are offering a sequence of six lighting courses leading to a certificate; the first graduating class is now coming out of both Cypress and Consumnes Community Colleges. At Cal Poly University a four course/laboratory sequence leading to a minor in Illumination Engineering (ILE) is now offered to upper division students in the College of Engineering, College of Science and College of Architecture and Design. The ILE sequence will briefly be described. The first course, Introduction to Illumination Engineering and its laboratory are described in more detail alter. Various methods of instruction including lectures, self work, industrial visits and guest lectures, as well as the accompanying laboratory work are discussed. Feedback from the students was very positive.

Diversity and Equity in the Lab: Preparing Scientists and Engineers for Inclusive Teaching in Courses and Research Environments

NASA Astrophysics Data System (ADS)

Hunter, L.; Seagroves, S.; Metevier, A. J.; Kluger-Bell, B.; Raschke, L.; Jonsson, P.; Porter, J.; Brown, C.; Roybal, G.; Shaw, J.

2010-12-01

Despite high attrition rates in college-level science, technology, engineering, and math (STEM) courses, with even higher rates for women and underrepresented minorities, not enough attention has been given to higher education STEM classroom practices that may limit the retention of students from diverse backgrounds. The Professional Development Program (PDP) has developed a range of professional development activities aimed at helping participants learn about diversity and equity issues, integrate inclusive teaching strategies into their own instructional units, and reflect on their own teaching practices. In the PDP, all participants develop and teach a STEM laboratory activity that enables their students to practice scientific inquiry processes as they gain an understanding of scientific concepts. In addition, they are asked to consider diversity and equity issues in their activity design and teaching. The PDP supports participants in this challenging endeavor by engaging them in activities that are aligned with a PDP-defined Diversity & Equity Focus Area that includes five emphases: 1) Multiple ways to learn, communicate and succeed; 2) Learners' goals, interests, motivation, and values; 3) Beliefs and perceptions about ability to achieve; 4) Inclusive collaboration and equitable participation; 5) Social identification within STEM culture. We describe the PDP Diversity & Equity focus, the five emphases, and the supporting activities that have been designed and implemented within the PDP, as well as future directions for our diversity and equity efforts.

A Simple Laboratory Scale Model of Iceberg Dynamics and its Role in Undergraduate Education

NASA Astrophysics Data System (ADS)

Burton, J. C.; MacAyeal, D. R.; Nakamura, N.

2011-12-01

Lab-scale models of geophysical phenomena have a long history in research and education. For example, at the University of Chicago, Dave Fultz developed laboratory-scale models of atmospheric flows. The results from his laboratory were so stimulating that similar laboratories were subsequently established at a number of other institutions. Today, the Dave Fultz Memorial Laboratory for Hydrodynamics (http://geosci.uchicago.edu/~nnn/LAB/) teaches general circulation of the atmosphere and oceans to hundreds of students each year. Following this tradition, we have constructed a lab model of iceberg-capsize dynamics for use in the Fultz Laboratory, which focuses on the interface between glaciology and physical oceanography. The experiment consists of a 2.5 meter long wave tank containing water and plastic "icebergs". The motion of the icebergs is tracked using digital video. Movies can be found at: http://geosci.uchicago.edu/research/glaciology_files/tsunamigenesis_research.shtml. We have had 3 successful undergraduate interns with backgrounds in mathematics, engineering, and geosciences perform experiments, analyze data, and interpret results. In addition to iceberg dynamics, the wave-tank has served as a teaching tool in undergraduate classes studying dam-breaking and tsunami run-up. Motivated by the relatively inexpensive cost of our apparatus (~1K-2K dollars) and positive experiences of undergraduate students, we hope to serve as a model for undergraduate research and education that other universities may follow.

Implementation and use of cloud-based electronic lab notebook in a bioprocess engineering teaching laboratory.

PubMed

Riley, Erin M; Hattaway, Holly Z; Felse, P Arthur

2017-01-01

Electronic lab notebooks (ELNs) are better equipped than paper lab notebooks (PLNs) to handle present-day life science and engineering experiments that generate large data sets and require high levels of data integrity. But limited training and a lack of workforce with ELN knowledge have restricted the use of ELN in academic and industry research laboratories which still rely on cumbersome PLNs for recordkeeping. We used LabArchives, a cloud-based ELN in our bioprocess engineering lab course to train students in electronic record keeping, good documentation practices (GDPs), and data integrity. Implementation of ELN in the bioprocess engineering lab course, an analysis of user experiences, and our development actions to improve ELN training are presented here. ELN improved pedagogy and learning outcomes of the lab course through stream lined workflow, quick data recording and archiving, and enhanced data sharing and collaboration. It also enabled superior data integrity, simplified information exchange, and allowed real-time and remote monitoring of experiments. Several attributes related to positive user experiences of ELN improved between the two subsequent years in which ELN was offered. Student responses also indicate that ELN is better than PLN for compliance. We demonstrated that ELN can be successfully implemented in a lab course with significant benefits to pedagogy, GDP training, and data integrity. The methods and processes presented here for ELN implementation can be adapted to many types of laboratory experiments.

Future Engineering Professors' Conceptions of Learning and Teaching Engineering

ERIC Educational Resources Information Center

Torres Ayala, Ana T.

2012-01-01

Conceptions of learning and teaching shape teaching practices and are, therefore, important to understanding how engineering professors learn to teach. There is abundant research about professors' conceptions of teaching; however, research on the conceptions of teaching of doctoral students, the future professors, is scarce. Furthermore,…

Research approach to teaching groundwater biodegradation in karst aquifers

USGS Publications Warehouse

King, L.; Byl, T.; Painter, R.

2006-01-01

TSU in partnership with the USGS has conducted extensive research regarding biode??gradation of contaminants in karst aquifers. This research resulted in the development of a numerical approach to modeling biodegradation of contaminants in karst aquifers that is taught to environmental engineering students in several steps. First, environmental engineering students are taught chemical-reaction engineering principles relating to a wide variety of environmental fate and transport issues. Second, as part of TSU's engineering course curriculum, students use a non-ideal flow laboratory reactor system and run a tracer study to establish residence time distribution (RTD). Next, the students couple that formula to a first-order biodegradation rate and predict the removal of a biodegradable contaminant as a function of residence time. Following this, students are shown data collected from karst bedrock wells that suggest that karst aquifers are analogous to non-ideal flow reactors. The students are challenged to develop rates of biodegradation through lab studies and use their results to predict biodegradaton at an actual contaminated karst site. Field studies are also conducted to determine the accuracy of the students' predictions. This academic approach teaches biodegradation processes, rate-kinetic processes, hydraulic processes and numerical principles. The students are able to experience how chemical engineering principles can be applied to other situations, such as, modeling biodegradation of contaminants in karst aquifers. This paper provides background on the chemical engineering principles and karst issues used in the research-enhanced curriculum. ?? American Society for Engineering Education, 2006.

An Example of a Laboratory Teaching Experience in a Professional Year (Plan B) Program

ERIC Educational Resources Information Center

Miller, P. J.; And Others

1978-01-01

A laboratory teaching experience (L.T.E.) was designed to focus on three teaching behaviors. It was recognized that a behavioral approach to teaching simplified its complexity by isolating specific teaching behaviors. Discusses the development and evaluation of the laboratory teaching experience. (Author/RK)

Teaching Chemical Engineers about Teaching

ERIC Educational Resources Information Center

Heath, Daniel E.; Hoy, Mary; Rathman, James F.; Rohdieck, Stephanie

2013-01-01

The Chemical and Biomolecular Engineering Department at The Ohio State University in collaboration with the University Center for the Advancement of Teaching developed the Chemical Engineering Mentored Teaching Experience. The Mentored Teaching Experience is an elective for Ph.D. students interested in pursuing faculty careers. Participants are…

Hydrogen and the materials of a sustainable energy future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zalbowitz, M.

1997-02-01

The National Educator`s Workshop (NEW): Update 96 was held October 27--30, 1996, and was hosted by Los Alamos National Laboratory. This was the 11th annual conference aimed at improving the teaching of material science, engineering and technology by updating educators and providing laboratory experiments on emerging technology for teaching fundamental and newly evolving materials concepts. The Hydrogen Education Outreach Activity at Los Alamos National Laboratory organized a special conference theme: Hydrogen and the Materials of a Sustainable Energy Future. The hydrogen component of the NEW:Update 96 offered the opportunity for educators to have direct communication with scientists in laboratory settings,more » develop mentor relationship with laboratory staff, and bring leading edge materials/technologies into the classroom to upgrade educational curricula. Lack of public education and understanding about hydrogen is a major barrier for initial implementation of hydrogen energy technologies and is an important prerequisite for acceptance of hydrogen outside the scientific/technical research communities. The following materials contain the papers and view graphs from the conference presentations. In addition, supplemental reference articles are also included: a general overview of hydrogen and an article on handling hydrogen safely. A resource list containing a curriculum outline, bibliography, Internet resources, and a list of periodicals often publishing relevant research articles can be found in the last section.« less

The Brazilian research and teaching center in biomedicine and aerospace biomedical engineering.

PubMed

Russomano, T; Falcao, P F; Dalmarco, G; Martinelli, L; Cardoso, R; Santos, M A; Sparenberg, A

2008-08-01

The recent engagement of Brazil in the construction and utilization of the International Space Station has motivated several Brazilian research institutions and universities to establish study centers related to Space Sciences. The Pontificia Universidade Catolica do Rio Grande do Sul (PUCRS) is no exception. The University initiated in 1993 the first degree course training students to operate commercial aircraft in South America (the School of Aeronautical Sciences. A further step was the decision to build the first Brazilian laboratory dedicated to the conduct of experiments in ground-based microgravity simulation. Established in 1998, the Microgravity Laboratory, which was located in the Instituto de Pesquisas Cientificas e Tecnologicas (IPCT), was supported by the Schools of Medicine, Aeronautical Sciences and Electrical Engineering/Biomedical Engineering. At the end of 2006, the Microgravity Laboratory became a Center and was transferred to the School of Engineering. The principal activities of the Microgravity Centre are the development of research projects related to human physiology before, during and after ground-based microgravity simulation and parabolic flights, to aviation medicine in the 21st century and to aerospace biomedical engineering. The history of Brazilian, and why not say worldwide, space science should unquestionably go through PUCRS. As time passes, the pioneering spirit of our University in the aerospace area has become undeniable. This is due to the group of professionals, students, technicians and staff in general that have once worked or are still working in the Center of Microgravity, a group of faculty and students that excel in their undeniable technical-scientific qualifications.

Graduate Teaching Assistants; Critical Colleagues or Casual Components in the Undergraduate Laboratory Learning? An Exploration of the Role of the Postgraduate Teacher in the Sciences

ERIC Educational Resources Information Center

Ryan, Barry J.

2014-01-01

Laboratory training is key to many science subjects and those that teach the practical laboratory skills maintain a pivotal role in undergraduate science training. Graduate Teaching Assistants (GTAs) are regularly used in higher education institutes to teach these practical lab skills. The GTA can be involved in both laboratory teaching and…

Designing Effective Undergraduate Research Experiences

NASA Astrophysics Data System (ADS)

Severson, S.

2010-12-01

I present a model for designing student research internships that is informed by the best practices of the Center for Adaptive Optics (CfAO) Professional Development Program. The dual strands of the CfAO education program include: the preparation of early-career scientists and engineers in effective teaching; and changing the learning experiences of students (e.g., undergraduate interns) through inquiry-based "teaching laboratories." This paper will focus on the carry-over of these ideas into the design of laboratory research internships such as the CfAO Mainland internship program as well as NSF REU (Research Experiences for Undergraduates) and senior-thesis or "capstone" research programs. Key ideas in maximizing student learning outcomes and generating productive research during internships include: defining explicit content, scientific process, and attitudinal goals for the project; assessment of student prior knowledge and experience, then following up with formative assessment throughout the project; setting reasonable goals with timetables and addressing motivation; and giving students ownership of the research by implementing aspects of the inquiry process within the internship.

Teaching problem solving: Don't forget the problem solver(s)

NASA Astrophysics Data System (ADS)

Ranade, Saidas M.; Corrales, Angela

2013-05-01

The importance of intrapersonal and interpersonal intelligences has long been known but educators have debated whether to and how to incorporate those topics in an already crowded engineering curriculum. In 2010, the authors used the classroom as a laboratory to observe the usefulness of including selected case studies and exercises from the fields of neurology, artificial intelligence, cognitive sciences and social psychology in a new problem-solving course. To further validate their initial findings, in 2012, the authors conducted an online survey of engineering students and engineers. The main conclusion is that engineering students will benefit from learning more about the impact of emotions, culture, diversity and cognitive biases when solving problems. Specifically, the work shows that an augmented problem-solving curriculum needs to include lessons on labelling emotions and cognitive biases, 'evidence-based' data on the importance of culture and diversity and additional practice on estimating conditional probability.

A comparison of traditional physical laboratory and computer-simulated laboratory experiences in relation to engineering undergraduate students' conceptual understandings of a communication systems topic

NASA Astrophysics Data System (ADS)

Javidi, Giti

2005-07-01

This study was designed to investigate an alternative to the use of traditional physical laboratory activities in a communication systems course. Specifically, this study examined whether as an alternative, computer simulation is as effective as physical laboratory activities in teaching college-level electronics engineering education students about the concepts of signal transmission, modulation and demodulation. Eighty undergraduate engineering students participated in the study, which was conducted at a southeastern four-year university. The students were randomly assigned to two groups. The groups were compared on understanding the concepts, remembering the concepts, completion time of the lab experiments and perception toward the laboratory experiments. The physical group's (n = 40) treatment was to conduct laboratory experiments in a physical laboratory. The students in this group used equipment in a controlled electronics laboratory. The Simulation group's (n = 40) treatment was to conduct similar experiments in a PC laboratory. The students in this group used a simulation program in a controlled PC lab. At the completion of the treatment, scores on a validated conceptual test were collected once after the treatment and again three weeks after the treatment. Attitude surveys and qualitative study were administered at the completion of the treatment. The findings revealed significant differences, in favor of the simulation group, between the two groups on both the conceptual post-test and the follow-up test. The findings also revealed significant correlation between simulation groups' attitude toward the simulation program and their post-test scores. Moreover, there was a significant difference between the two groups on their attitude toward their laboratory experience in favor of the simulation group. In addition, there was significant difference between the two groups on their lab completion time in favor of the simulation group. At the same time, the qualitative research has uncovered several issues not explored by the quantitative research. It was concluded that incorporating the recommendations acquired from the qualitative research, especially elements of incorporating hardware experience to avoid lack of hands-on skills, into the laboratory pedagogy should help improve students' experience regardless of the environment in which the laboratory is conducted.

Maximising resource allocation in the teaching laboratory: understanding student evaluations of teaching assistants in a team-based teaching format

NASA Astrophysics Data System (ADS)

Nikolic, Sasha; Suesse, Thomas F.; McCarthy, Timothy J.; Goldfinch, Thomas L.

2017-11-01

Minimal research papers have investigated the use of student evaluations on the laboratory, a learning medium usually run by teaching assistants with little control of the content, delivery and equipment. Finding the right mix of teaching assistants for the laboratory can be an onerous task due to the many skills required including theoretical and practical know-how, troubleshooting, safety and class management. Using larger classes with multiple teaching assistants, a team-based teaching (TBT) format may be advantageous. A rigorous three-year study across twenty-five courses over repetitive laboratory classes is analysed using a multi-level statistical model considering students, laboratory classes and courses. The study is used to investigate the effectiveness of the TBT format, and quantify the influence each demonstrator has on the laboratory experience. The study found that TBT is effective and the lead demonstrator most influential, influencing up to 55% of the laboratory experience evaluation.

Student experience of a scenario-centred curriculum

NASA Astrophysics Data System (ADS)

Bell, Sarah; Galilea, Patricia; Tolouei, Reza

2010-06-01

In 2006 UCL implemented new scenario-centred degree programmes in Civil and Environmental Engineering. The new curriculum can be characterised as a hybrid of problem-based, project-based and traditional approaches to learning. Four times a year students work in teams for one week on a scenario which aims to integrate learning from lecture and laboratory classes and to develop generic skills including team working and communication. Student experience of the first two years the old and new curricula were evaluated using a modified Course Experience Questionnaire. The results showed that students on the new programme were motivated by the scenarios and perceived better generic skills development, but had a lower perception of teaching quality and the development of design skills. The results of the survey support the implementation new curriculum but highlight the importance of strong integration between conventional teaching and scenarios, and the challenges of adapting teaching styles to suit.

Teaching Agile Software Engineering Using Problem-Based Learning

ERIC Educational Resources Information Center

El-Khalili, Nuha H.

2013-01-01

Many studies have reported the utilization of Problem-Based Learning (PBL) in teaching Software Engineering courses. However, these studies have different views of the effectiveness of PBL. This paper presents the design of an Advanced Software Engineering course for undergraduate Software Engineering students that uses PBL to teach them Agile…

Teaching Green Engineering: The Case of Ethanol Lifecycle Analysis

ERIC Educational Resources Information Center

Vallero, Daniel A.; Braiser, Chris

2008-01-01

Lifecycle assessment (LCA) is a valuable tool in teaching green engineering and has been used to assess biofuels, including ethanol. An undergraduate engineering course at Duke University has integrated LCA with other interactive teaching techniques to enhance awareness and to inform engineering decision making related to societal issues, such as…

[Improving experimental teaching facilities and opening up of laboratories in order to raise experimental teaching quality of genetics].

PubMed

Xiao, Jian-Fu; Wu, Jian-Guo; Shi, Chun-Hai

2011-12-01

Advanced teaching facilities and the policy of opening laboratories to students play an important role in raising the quality in the experimental teaching of Genetics. This article introduces the superiority of some advanced instruments and equipment (such as digital microscope mutual laboratory system, flow cytometry, and NIRSystems) in the experimental teaching of genetics, and illustrates with examples the significance of exposing students to experiments in developing their creative consciousness and creative ability. This article also offers some new concepts on the further improvement upon teaching in the laboratory.

Catalyzing Graduate Teaching Assistants' Laboratory Teaching through Design Research

ERIC Educational Resources Information Center

Bond-Robinson, Janet; Rodriques, Romola A. Bernard

2006-01-01

We report on a study of a laboratory teaching apprenticeship program designed to improve graduate teaching assistant (GTA) performance. To catalyze GTAs as laboratory teachers we constructed learning goals, synthesized previous literature into a design model and a developmental path, and built two instruments to measure 12 strategic pedagogical…

Aligning Perceptions of Laboratory Demonstrators' Responsibilities to Inform the Design of a Laboratory Teacher Development Program

ERIC Educational Resources Information Center

Flaherty, Aishling; O'Dwyer, Anne; Mannix-McNamara, Patricia; Leahy, J. J.

2017-01-01

Throughout countries such as Ireland, the U.K., and Australia, graduate students who fulfill teaching roles in the undergraduate laboratory are often referred to as "laboratory demonstrators". The laboratory demonstrator (LD) model of graduate teaching is similar to the more commonly known graduate teaching assistant (GTA) model that is…

The Scholarship of Teaching: The CEET Initiative on Teaching and Learning. A Faculty Development Program on Teaching and Learning and Classroom Research. Volumes 1-4. October 2005-December 2006

ERIC Educational Resources Information Center

Scarborough, Jule Dee

2007-01-01

This Northern Illinois University College of Engineering and Engineering Technology (CEET) initiative represents the authors' first attempt to prepare engineering and technology professors for teaching to improve student learning and the Scholarship of Teaching. This college portfolio is nontraditional in that it combines a learning paper approach…

Educational ultrasound nondestructive testing laboratory.

PubMed

Genis, Vladimir; Zagorski, Michael

2008-09-01

The ultrasound nondestructive evaluation (NDE) of materials course was developed for applied engineering technology students at Drexel University's Goodwin College of Professional Studies. This three-credit, hands-on laboratory course consists of two parts: the first part with an emphasis on the foundations of NDE, and the second part during which ultrasound NDE techniques are utilized in the evaluation of parts and materials. NDE applications are presented and applied through real-life problems, including calibration and use of the latest ultrasonic testing instrumentation. The students learn engineering and physical principles of measurements of sound velocity in different materials, attenuation coefficients, material thickness, and location and dimensions of discontinuities in various materials, such as holes, cracks, and flaws. The work in the laboratory enhances the fundamentals taught during classroom sessions. This course will ultimately result in improvements in the educational process ["The greater expectations," national panel report, http://www.greaterexpectations.org (last viewed February, 2008); R. M. Felder and R. Brent "The intellectual development of Science and Engineering Students. Part 2: Teaching to promote growth," J. Eng. Educ. 93, 279-291 (2004)] since industry is becoming increasingly reliant on the effective application of NDE technology and the demand on NDE specialists is increasing. NDE curriculum was designed to fulfill levels I and II NDE in theory and training requirements, according to American Society for Nondestructive Testing, OH, Recommended Practice No. SNT-TC-1A (2006).

The Research of Software Engineering Curriculum Reform

NASA Astrophysics Data System (ADS)

Kuang, Li-Qun; Han, Xie

With the problem that software engineering training can't meet the needs of the community, this paper analysis some outstanding reasons in software engineering curriculum teaching, such as old teaching contents, weak in practice and low quality of teachers etc. We propose the methods of teaching reform as guided by market demand, update the teaching content, optimize the teaching methods, reform the teaching practice, strengthen the teacher-student exchange and promote teachers and students together. We carried out the reform and explore positive and achieved the desired results.

Multiple case studies of STEM teachers' orientations to science teaching through engineering design

NASA Astrophysics Data System (ADS)

Rupp, Madeline

The following master's thesis is composed of two manuscripts describing STEM teachers' orientations to science teaching through engineering within the context of the Science Learning through Engineering Design (SLED) partnership. The framework guiding both studies was science teaching orientations, a component of pedagogical content knowledge. Data were collected via semi-structured interviews, multi-day classroom observations, pre- and post-observation interviews, implementation plans, and written reflections. Data sources were analyzed to generate two orientations to science teaching through engineering design for each participant. The first manuscript illustrates a single case study conducted with a sixth grade STEM teacher. Results of this study revealed a detailed picture of the teacher's goals, practices, assessments, and general views when teaching science through engineering design. Common themes across the teacher's instruction were used to characterize her orientations to science teaching through engineering design. Overall, the teacher's orientations showed a shift in her practice from didactic to student-centered methods of teaching as a result of integrating engineering design-based curriculum. The second manuscript describes a comparative case study of two sixth grade SLED participants. Results of this study revealed more complex and diverse relationships between the teachers' orientations to teaching science through engineering design and their instruction. Participants' orientations served as filters for instruction, guided by their divergent purposes for science teaching. Furthermore, their orientations and resulting implementation were developed from knowledge gained in teacher education, implying that teacher educators and researchers can use this framework to learn more about how teachers' knowledge is used to integrate engineering and science practices in the K-12 classroom.

Maximising Resource Allocation in the Teaching Laboratory: Understanding Student Evaluations of Teaching Assistants in a Team-Based Teaching Format

ERIC Educational Resources Information Center

Nikolic, Sasha; Suesse, Thomas F.; McCarthy, Timothy J.; Goldfinch, Thomas L.

2017-01-01

Minimal research papers have investigated the use of student evaluations on the laboratory, a learning medium usually run by teaching assistants with little control of the content, delivery and equipment. Finding the right mix of teaching assistants for the laboratory can be an onerous task due to the many skills required including theoretical and…

Putting the Laboratory at the Center of Teaching Chemistry

ERIC Educational Resources Information Center

Bopegedera, A. M. R. P.

2011-01-01

This article describes an effective approach to teaching chemistry by bringing the laboratory to the center of teaching, to bring the excitement of discovery to the learning process. The lectures and laboratories are closely integrated to provide a holistic learning experience. The laboratories progress from verification to open-inquiry and…

Engineering Encounters: Teaching Educators about Engineering

ERIC Educational Resources Information Center

Tank, Kristina M.; Raman, D. Raj; Lamm, Monica H.; Sundararajan, Sriram; Estapa, Anne

2017-01-01

This column presents ideas and techniques to enhance science teaching. This month's issue describes preservice elementary teachers learning engineering principles from engineers. Few elementary teachers have experience with implementing engineering into the classroom. While engineering professional development opportunities for inservice teachers…

Laboratory-based teaching and the Physics Innovations Centre for Excellence in Teaching and Learning

NASA Astrophysics Data System (ADS)

Lambourne, Robert

2007-05-01

Developments in the laboratory-based teaching of physics and astronomy are resulting from the collaboration between conventional and distance teaching universities. The collaboration, piCETL, is one of the Centres for Excellence in Teaching and Learning established as a result of a broad initiative by the Higher Education Funding Council for England. The initiative, the piCETL collaboration and some of its work on laboratory-based teaching are all described.

Embedding Entrepreneurial Thinking into Fluids-related Courses: Small Changes Lead to Positive Results

NASA Astrophysics Data System (ADS)

Carnasciali, Maria-Isabel

2017-11-01

Many fluid dynamics instructors have embraced student-centered learning pedagogies (Active & Collaborative Learning (ACL) and Problem/Project Based Learning (PBL)) to promote learning and increase student engagement. A growing effort in engineering education calls to equip students with entrepreneurial skills needed to drive innovation. The Kern Entrepreneurial Engineering Network (KEEN) defines entrepreneurial mindset based on three key attributes: curiosity, connections, and creating value. Elements of ACL and PBL have been used to embed Entrepreneurial Thinking concepts into two fluids-related subjects: 1) an introductory thermal-fluid systems course, and 2) thermo-fluids laboratory. Assessment of students' work reveal an improvement in student learning. Course Evaluations and Surveys indicate an increased perceived-value of course content. Training and development made possible through funding from the Kern Entrepreneurial Engineering Network and the Bucknall Excellence in Teaching Award.

Group of R&D on biomedical engineering: Its development and results.

PubMed

Yabar, Leopoldo F; Torres, Miguel A; Garcia, Daniel O; Villavicencio, Emilio A; Navarro, Luis A; Nakamura, Orlando K; Huamani, Robinson

2010-01-01

Conducting research and development activities generates new knowledge that can then be applied properly. In this sense, the groups of research and development on biomedical engineering (GRDBE) can contribute a lot in various areas such as teaching (theory and laboratory), as well as the development of prototypes, but mainly with the results they can provide. These contributions should response to specific needs of some sector, for example: health, environment, biology, and others. The present paper provides a description of the development of a GRDBE into a private university. Also, it's presented the amount of papers developed by this group and accepted by international congress on biomedical engineering (BE) on the 2007-2009 period. This paper also shows comparative charts with papers produced by other GRDBE that exist in our country, which are matter of analysis and conclusions.

Practice in Master Course of Techno-Business Administration as a Techno-Business School

NASA Astrophysics Data System (ADS)

Nakamura, Takashi; Matsuura, Chikako

In this paper, the educational practice of the master course of techno-business administration (MTA) at Nagoya Institute of Technology (NIT) is introduced to propose the practical engineering education at a postgraduate level. MTA was established in 2003 on the basis of hundred years' engineering education at NIT. An objective of this school is to educate engineers to be leaders, entrepreneurs and managers. The practical tuition covers the fields in Industrial Management of Technologies, Core-Technologies and Laboratories work. Among these, the most focused and effective subject is “Case-Study,” in which students are encouraged to simulate business settings using elemental technologies developed by teaching staff. Discussions are made to apply the technology to match the possible markets. This type of experiences certainly motivates the students work and is clearly reflected in their research paper.

Chemistry Graduate Teaching Assistants' Experiences in Academic Laboratories and Development of a Teaching Self-image

NASA Astrophysics Data System (ADS)

Gatlin, Todd Adam

Graduate teaching assistants (GTAs) play a prominent role in chemistry laboratory instruction at research based universities. They teach almost all undergraduate chemistry laboratory courses. However, their role in laboratory instruction has often been overlooked in educational research. Interest in chemistry GTAs has been placed on training and their perceived expectations, but less attention has been paid to their experiences or their potential benefits from teaching. This work was designed to investigate GTAs' experiences in and benefits from laboratory instructional environments. This dissertation includes three related studies on GTAs' experiences teaching in general chemistry laboratories. Qualitative methods were used for each study. First, phenomenological analysis was used to explore GTAs' experiences in an expository laboratory program. Post-teaching interviews were the primary data source. GTAs experiences were described in three dimensions: doing, knowing, and transferring. Gains available to GTAs revolved around general teaching skills. However, no gains specifically related to scientific development were found in this laboratory format. Case-study methods were used to explore and illustrate ways GTAs develop a GTA self-image---the way they see themselves as instructors. Two general chemistry laboratory programs that represent two very different instructional frameworks were chosen for the context of this study. The first program used a cooperative project-based approach. The second program used weekly, verification-type activities. End of the semester interviews were collected and served as the primary data source. A follow-up case study of a new cohort of GTAs in the cooperative problem-based laboratory was undertaken to investigate changes in GTAs' self-images over the course of one semester. Pre-semester and post-semester interviews served as the primary data source. Findings suggest that GTAs' construction of their self-image is shaped through the interaction of 1) prior experiences, 2) training, 3) beliefs about the nature of knowledge, 4) beliefs about the nature of laboratory work, and 5) involvement in the laboratory setting. Further GTAs' self-images are malleable and susceptible to change through their laboratory teaching experiences. Overall, this dissertation contributes to chemistry education by providing a model useful for exploring GTAs' development of a self-image in laboratory teaching. This work may assist laboratory instructors and coordinators in reconsidering, when applicable, GTA training and support. This work also holds considerable implications for how teaching experiences are conceptualized as part of the chemistry graduate education experience. Findings suggest that appropriate teaching experiences may contribute towards better preparing graduate students for their journey in becoming scientists.

Do Graduate Teaching Assistants Benefit from Teaching Inquiry-Based Laboratories?

ERIC Educational Resources Information Center

French, Donald; Russell, Connie

2002-01-01

Introduces a study investigating graduate teaching assistants' (GTA) perceptions on their role in conducting laboratories and explores the benefits of inquiry-based laboratories for GTAs considering their experiences and knowledge. (Contains 22 references.) (YDS)

Teaching Engineering Ethics to PhD Students: A Berkeley-Delft Initiative : Commentary on "Ethics Across the Curriculum: Prospects for Broader (and Deeper) Teaching and Learning in Research and Engineering Ethics".

PubMed

Taebi, Behnam; Kastenberg, William E

2016-07-13

A joint effort by the University of California at Berkeley and Delft University of Technology to develop a graduate engineering ethics course for PhD students encountered two types of challenges: academic and institutional. Academically, long-term collaborative research efforts between engineering and philosophy faculty members might be needed before successful engineering ethics courses can be initiated; the teaching of ethics to engineering graduate students and collaborative research need to go hand-in-hand. Institutionally, both bottom-up approaches at the level of the faculty and as a joint research and teaching effort, and top-down approaches that include recognition by a University's administration and the top level of education management, are needed for successful and sustainable efforts to teach engineering ethics.

How to Make Mathematics Relevant to First-Year Engineering Students: Perceptions of Students on Student-Produced Resources

ERIC Educational Resources Information Center

Loch, Birgit; Lamborn, Julia

2016-01-01

Many approaches to make mathematics relevant to first-year engineering students have been described. These include teaching practical engineering applications, or a close collaboration between engineering and mathematics teaching staff on unit design and teaching. In this paper, we report on a novel approach where we gave higher year engineering…

Do Teaching Assistants Matter? Investigating Relationships between Teaching Assistants and Student Outcomes in Undergraduate Science Laboratory Classes

ERIC Educational Resources Information Center

Wheeler, Lindsay B.; Maeng, Jennifer L.; Chiu, Jennie L.; Bell, Randy L.

2017-01-01

This study explores the relationship between teaching assistants (TAs) and student learning in undergraduate science laboratory classes. TAs typically instruct laboratory courses, yet little, if any, research examines professional development (PD) for TAs or relationships between instructors and students in laboratory settings. The use of…

How to Teach Engineering and Industrial Design: a U.K. Experience.

ERIC Educational Resources Information Center

Sheldon, D. F.

1988-01-01

Explored are the possibilities of teaching engineering through a project approach. Discussed are the introduction, clashing cultures of industrial and engineering design, skills required of a designer, teaching approach to the total design activity, CAD/CAM experiences, and conclusions. (Author/YP)

Examining the Extent to Which Select Teacher Preparation Experiences Inform Technology and Engineering Educators' Teaching of Science Content and Practices

ERIC Educational Resources Information Center

Love, Tyler S.

2015-01-01

With the recent release of the "Next Generation Science Standards" (NGSS) (NGSS Lead States, 2014b) science educators were expected to teach engineering content and practices within their curricula. However, technology and engineering (T&E) educators have been expected to teach content and practices from engineering and other…

Why research-informed teaching in engineering education? A review of the evidence

NASA Astrophysics Data System (ADS)

Bubou, Gordon Monday; Offor, Ibebietei Temple; Bappa, Abubakar Saddiq

2017-05-01

Challenges of today's engineering education (EE) are emergent, necessitating calls for its reformation to empower future engineers function optimally as innovative leaders, in both local and international contexts. These challenges: keeping pace with technological dynamism; high attrition; and most importantly, quality teaching/learning require multifaceted approaches. But how can EE respond to the growing demand for relevant teaching? What can we do for engineering faculties to leverage on quality teaching? How do we embed quality teaching in EE? Scholarship of teaching and learning is advocated as one viable approach. It uses evidence-based teaching (EBT) strategies, and research-informed evidence to guide educational decisions regarding teaching and learning. We review the theories underpinning EBT, the scientific evidence on which it is based, and innovative instructional strategies that enhance active learning. Some of these issues have been discussed already, largely through developing countries lens. Nevertheless, linkages to equivalent global perspectives are presented here.

Evaluating the Impact of the "Teaching as a Chemistry Laboratory Graduate Teaching Assistant" Program on Cognitive and Psychomotor Verbal Interactions in the Laboratory

ERIC Educational Resources Information Center

Flaherty, A.; O'Dwyer, A.; Mannix-McNamara, P.; Leahy, J. J.

2017-01-01

Designing and evaluating teacher development programs for graduate teaching assistants (GTAs) who teach in the laboratory is a prominent feature of chemistry education research. However, few studies have investigated the impact of a GTA teacher development program on the verbal interactions between participating GTAs and students in the…

Exploration of Factors Related to the Development of Science, Technology, Engineering, and Mathematics Graduate Teaching Assistants' Teaching Orientations

ERIC Educational Resources Information Center

Gilmore, Joanna; Maher, Michelle A.; Feldon, David F.; Timmerman, Briana

2014-01-01

Research indicates that modifying teachers' beliefs about learning and teaching (i.e. teaching orientation) may be a prerequisite to changing their teaching practices. This mixed methods study quantitized data from interviews with 65 graduate teaching assistants (GTAs) from science, technology, engineering, and mathematics (STEM) fields to assess…

Mars mission program for primary students: Building student and teacher skills in science, technology, engineering and mathematics

NASA Astrophysics Data System (ADS)

Mathers, Naomi; Pakakis, Michael; Christie, Ian

2011-09-01

The Victorian Space Science Education Centre (VSSEC) scenario-based programs, including the Mission to Mars and Mission to the Orbiting Space Laboratory, utilize methodologies such as hands-on applications, immersive learning, integrated technologies, critical thinking and mentoring. The use of a scenario provides a real-life context and purpose to what students might otherwise consider disjointed information. These programs engage students in the areas of maths and science, and highlight potential career paths in science and engineering. The introduction of a scenario-based program for primary students engages students in maths and science at a younger age, addressing the issues of basic numeracy and science literacy, thus laying the foundation for stronger senior science initiatives. Primary students absorb more information within the context of the scenario, and presenting information they can see, hear, touch and smell creates a memorable learning and sensory experience. The mission also supports development of teacher skills in the delivery of hands-on science and helps build their confidence to teach science. The Primary Mission to the Mars Base gives primary school students access to an environment and equipment not available in schools. Students wear flight suits for the duration of the program to immerse them in the experience of being an astronaut. Astronauts work in the VSSEC Space Laboratory, which is transformed into a Mars base for the primary program, to conduct experiments in areas such as robotics, human physiology, microbiology, nanotechnology and environmental science. Specialist mission control software has been developed by La Trobe University Centre for Games Technology to provide age appropriate Information and Communication Technology (ICT) based problem solving and support the concept of a mission. Students in Mission Control observe the astronauts working in the space laboratory and talk to them via the AV system. This interactive environment promotes high order thinking skills such as problem solving, team work, communication skills and leadership. To promote the teaching of science in the classroom, and prepare the students for their mission, the program includes a pre-visit program. These classroom-based lessons model best practice in effective science teaching and learning to support the development of confident primary science teachers.

Discussion on teaching reform of environmental planning and management

NASA Astrophysics Data System (ADS)

Zhang, Qiugen; Chen, Suhua; Xie, Yu; Wei, Li'an; Ding, Yuan

2018-05-01

The curriculum of environmental planning and management is an environmental engineering major curriculum established by the teaching steering committee of environmental science and engineering of Education Ministry, which is the core curriculum of Chinese engineering education professional certification. It plays an important role in cultivating environmental planning and environmental management ability of environmental engineering major. The selection and optimization of the course teaching content of environmental planning and management were discussed which including curriculum teaching content updating and optimizing and teaching resource system construction. The comprehensive application of teaching method was discussed which including teaching method synthesis and teaching method. The final combination of the assessment method was also discussed which including the formative assessment normal grades and the final result of the course examination. Through the curriculum comprehensive teaching reform, students' knowledge had been broadened, the subject status and autonomy of learning had been enhanced, students' learning interest had been motivated, the ability of students' finding, analyzing and solving problems had been improved. Students' innovative ability and positive spirit had been well cultivated.

Gaming, texting, learning? Teaching engineering ethics through students' lived experiences with technology.

PubMed

Voss, Georgina

2013-09-01

This paper examines how young peoples' lived experiences with personal technologies can be used to teach engineering ethics in a way which facilitates greater engagement with the subject. Engineering ethics can be challenging to teach: as a form of practical ethics, it is framed around future workplace experience in a professional setting which students are assumed to have no prior experience of. Yet the current generations of engineering students, who have been described as 'digital natives', do however have immersive personal experience with digital technologies; and experiential learning theory describes how students learn ethics more successfully when they can draw on personal experience which give context and meaning to abstract theories. This paper reviews current teaching practices in engineering ethics; and examines young people's engagement with technologies including cell phones, social networking sites, digital music and computer games to identify social and ethical elements of these practices which have relevance for the engineering ethics curricula. From this analysis three case studies are developed to illustrate how facets of the use of these technologies can be drawn on to teach topics including group work and communication; risk and safety; and engineering as social experimentation. Means for bridging personal experience and professional ethics when teaching these cases are discussed. The paper contributes to research and curriculum development in engineering ethics education, and to wider education research about methods of teaching 'the net generation'.

Using Genre Analysis To Teach Writing in Engineering. Report on a Pilot Video-Teleconference for Engineering Teaching Assistants and Writing Center Consultants.

ERIC Educational Resources Information Center

Alford, Elisabeth; And Others

A pilot project tested and evaluated teleconferencing as a medium for training engineering teaching assistants in technical writing. The teleconference, which linked 15 participants in the engineering departments and writing centers of the University of South Carolina and Ohio State University, also included a training session on the use of genre…

Teaching methodologies to promote creativity in the professional skills related to optics knowledge

NASA Astrophysics Data System (ADS)

Fernández-Oliveras, Alicia; Fernandez, Paz; Peña-García, Antonio; Oliveras, Maria L.

2014-07-01

We present the methodologies proposed and applied in the context of a teaching-innovation project developed at the University of Granada, Spain. The main objective of the project is the implementation of teaching methodologies that promote the creativity in the learning process and, subsequently, in the acquisition of professional skills. This project involves two subjects related with optics knowledge in undergraduate students. The subjects are "Illumination Engineering" (Bachelor's degree in Civil-Engineering) and "Optical and Optometric Instrumentation" (Bachelor's degree in and Optics and Optometry). For the first subject, the activities of our project were carried out in the theoretical classes. By contrast, in the case of the second subject, such activities were designed for the laboratory sessions. For "Illumination Engineering" we applied the maieutic technique. With this method the students were encouraged to establish relationships between the main applications of the subject and concepts that apparently unrelated with the subject framework. By means of several examples, the students became aware of the importance of cross-curricular and lateral thinking. We used the technique based on protocols of control and change in "Optical and Optometric Instrumentation". The modus operandi was focused on prompting the students to adopt the role of the professionals and to pose questions to themselves concerning the practical content of the subject from that professional role. This mechanism boosted the critical capacity and the independent-learning ability of the students. In this work, we describe in detail both subject proposals and the results of their application in the 2011-2012 academic course.

A top-down approach in control engineering third-level teaching: The case of hydrogen-generation

NASA Astrophysics Data System (ADS)

Setiawan, Eko; Habibi, M. Afnan; Fall, Cheikh; Hodaka, Ichijo

2017-09-01

This paper presents a top-down approach in control engineering third-level teaching. The paper shows the control engineering solution for the issue of practical implementation in order to motivate students. The proposed strategy only focuses on one technique of control engineering to lead student correctly. The proposed teaching steps are 1) defining the problem, 2) listing of acquired knowledge or required skill, 3) selecting of one control engineering technique, 4) arrangement the order of teaching: problem introduction, implementation of control engineering technique, explanation of system block diagram, model derivation, controller design, and 5) enrichment knowledge by the other control techniques. The approach presented highlights hardware implementation and the use of software simulation as a self-learning tool for students.

Hands-on laboratory Experience in Teaching-Learning Physiology.

ERIC Educational Resources Information Center

Randall, Walter C.; Burkholder, Timothy

1990-01-01

The results of actual student participation, with organized group discussions, which show that laboratory teaching remains the premiere mechanism for teaching and learning organ-system physiology are discussed. Laboratories using a pithed frog, a turtle heart, an anesthetized rabbit, and noninvasive recordings from students during exercise are…

Developing a Virtual Rock Deformation Laboratory

NASA Astrophysics Data System (ADS)

Zhu, W.; Ougier-simonin, A.; Lisabeth, H. P.; Banker, J. S.

2012-12-01

Experimental rock physics plays an important role in advancing earthquake research. Despite its importance in geophysics, reservoir engineering, waste deposits and energy resources, most geology departments in U.S. universities don't have rock deformation facilities. A virtual deformation laboratory can serve as an efficient tool to help geology students naturally and internationally learn about rock deformation. Working with computer science engineers, we built a virtual deformation laboratory that aims at fostering user interaction to facilitate classroom and outreach teaching and learning. The virtual lab is built to center around a triaxial deformation apparatus in which laboratory measurements of mechanical and transport properties such as stress, axial and radial strains, acoustic emission activities, wave velocities, and permeability are demonstrated. A student user can create her avatar to enter the virtual lab. In the virtual lab, the avatar can browse and choose among various rock samples, determine the testing conditions (pressure, temperature, strain rate, loading paths), then operate the virtual deformation machine to observe how deformation changes physical properties of rocks. Actual experimental results on the mechanical, frictional, sonic, acoustic and transport properties of different rocks at different conditions are compiled. The data acquisition system in the virtual lab is linked to the complied experimental data. Structural and microstructural images of deformed rocks are up-loaded and linked to different deformation tests. The integration of the microstructural image and the deformation data allows the student to visualize how forces reshape the structure of the rock and change the physical properties. The virtual lab is built using the Game Engine. The geological background, outstanding questions related to the geological environment, and physical and mechanical concepts associated with the problem will be illustrated on the web portal. In addition, some web based data collection tools are available to collect student feedback and opinions on their learning experience. The virtual laboratory is designed to be an online education tool that facilitates interactive learning.; Virtual Deformation Laboratory

75 FR 48658 - Notice of Proposed Information Collection Requests

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-11

... individuals who teach science, technology, engineering, and math (STEM). TEACH.gov is an essential component... among minority individuals, and particularly in teaching science, technology, engineering, and math...

Two web-based laboratories of the FisL@bs network: Hooke's and Snell's laws

NASA Astrophysics Data System (ADS)

de la Torre, L.; Sánchez, J.; Dormido, S.; Sánchez, J. P.; Yuste, M.; Carreras, C.

2011-03-01

FisL@bs is a network of remote and virtual laboratories for physics university education via the Internet that offers students the possibility of performing hands-on experiments in different fields of physics in two ways: simulation and real remote operation. This paper gives a detailed account of a novel way in physics in which distance learning students can gain practical experience autonomously. FisL@bs uses the same structure as AutomatL@bs, a network of virtual and remote laboratories for learning/teaching of control engineering, which has been in operation for four years. Students can experiment with the laboratories offered using an Internet connection and a Java-compatible web browser. This paper, specially intended for university educators but easily comprehensible even for undergraduate students, explains how the portal works and the hardware and software tools used to create it. In addition, it also describes two physics experiments already available: spring elasticity and the laws of reflection and refraction.

Engineering Professional Development: Elementary Teachers' Self-efficacy and Sources of Self-efficacy

NASA Astrophysics Data System (ADS)

Webb, Donna Louise

Currently, STEM (science, technology, engineering, and mathematics) is a popular buzz word in P-12 education as it represents a means to advance American competitiveness in the global economy. Proponents of the engineering component of STEM advocate additional benefits in teaching engineering, such as its capacity to engage students in collaboration, and to apply critical thinking, systems thinking, negotiation, and communication skills to solve real-life contextual problems. Establishing a strong foundation of engineering knowledge at a young age will provide students with internal motivation as it taps into their curiosity toward how things work, and it also prepares them for secondary science courses. Successful STEM education is often constrained by elementary teachers' low perception of self-efficacy to teach science and engineering. Elementary teachers with low self-efficacy in science are more likely to spend less instructional time teaching science, which suggests that teachers with little to no training in engineering might avoid teaching this topic. Therefore, the purpose of this study was twofold: (a) to examine the effects of engineering professional development on elementary (K-6) teachers' content and pedagogical content knowledge (PCK) and perceptions of self-efficacy to teach engineering, and (b) to identify and explain sources influencing self-efficacy. Professional development was conducted in a metropolitan area in the Pacific Northwest. Results revealed that after the engineering professional development, teachers experienced statistically significant gains in content, PCK, and self-efficacy to teach engineering. Increases in self-efficacy were mainly attributed to mastery experiences and cultivation of a growth mindset by embracing the engineering design process.

Results of the 2010 Survey on Teaching Chemical Reaction Engineering

ERIC Educational Resources Information Center

Silverstein, David L.; Vigeant, Margot A. S.

2012-01-01

A survey of faculty teaching the chemical reaction engineering course or sequence during the 2009-2010 academic year at chemical engineering programs in the United States and Canada reveals change in terms of content, timing, and approaches to teaching. The report consists of two parts: first, a statistical and demographic characterization of the…

Engineering Motion

ERIC Educational Resources Information Center

Tuttle, Nicole; Stanley, Wendy; Bieniek, Tracy

2016-01-01

For many teachers, engineering can be intimidating; teachers receive little training in engineering, particularly those teaching early elementary students. In addition, the necessity of differentiating for students with special needs can make engineering more challenging to teach. This article describes a professional development program…

Safety in laboratories: Indian scenario.

PubMed

Mustafa, Ajaz; Farooq, A Jan; Qadri, Gj; S A, Tabish

2008-07-01

Health and safety in clinical laboratories is becoming an increasingly important subject as a result of emergence of highly infectious diseases such as Hepatitis and HIV. A cross sectional study was carried out to study the safety measures being adopted in clinical laboratories of India. Heads of laboratories of teaching hospitals of India were subjected to a standardized, pretested questionnaire. Response rate was 44.8%. only 60% of laboratories had person in-charge of safety in laboratory. Seventy three percent of laboratories had safety education program regarding hazards. In 91% of laboratories staff is using protective clothing while working in laboratories. Hazardous material regulations are followed in 78% of laboratories. Regular health check ups are carried among laboratory staff in 43.4% of laboratories.Safety manual is available in 56.5% of laboratories. 73.9% of laboratories are equipped with fire extinguishers. Fume cupboards are provided in 34.7% of laboratories and they are regularly checked in 87.5% of these laboratories. In 78.26% of laboratories suitable measures are taken to minimize formation of aerosols.In 95.6% of laboratories waste is disposed off as per bio-medical waste management handling rules. Laboratory of one private medical college was accredited with NABL and safety parameters were better in that laboratory. Installing safety engineered devices apparently contributes to significant decrease in injuries in laboratories; laboratory safety has to be a part of overall quality assurance programme in hospitals. Accreditation has to be made necessary for all laboratories.

Eight year experience in open ended instrumentation laboratory

NASA Astrophysics Data System (ADS)

Marques, Manuel B.; Rosa, Carla C.; Marques, Paulo V. S.

2015-10-01

When designing laboratory courses in a Physics Major we consider a range of objectives: teaching Physics; developing lab competencies; instrument control and data acquisition; learning about measurement errors and error propagation; an introduction to project management; team work skills and scientific writing. But nowadays we face pressure to decrease laboratory hours due to the cost involved. Many universities are replacing lab classes for simulation activities, hiring PhD. and master students to give first year lab classes, and reducing lab hours. This leads to formatted lab scripts and poor autonomy of the students, and failure to enhance creativity and autonomy. In this paper we present our eight year experience with a laboratory course that is mandatory in the third year of Physics and Physical Engineering degrees. Since the students had previously two standard laboratory courses, we focused on teaching instrumentation and giving students autonomy. The course is divided in two parts: one third is dedicated to learn computer controlled instrumentation and data acquisition (based in LabView); the final 2/3 is dedicated to a group project. In this project, the team (2 or 3 students) must develop a project and present it in a typical conference format at the end of the semester. The project assignments are usually not very detailed (about two or three lines long), giving only general guidelines pointing to a successful project (students often recycle objectives putting forward a very personal project); all of them require assembling some hardware. Due to our background, about one third of the projects are related to Optics.

Coherent Teaching and Need-Based Learning in Science: An Approach to Teach Engineering Students in Basic Physics Courses

ERIC Educational Resources Information Center

Kurki-Suonio, T.; Hakola, A.

2007-01-01

In the present paper, we propose an alternative, based on constructivism, to the conventional way of teaching basic physics courses at the university level. We call this approach "coherent teaching" and the underlying philosophy of teaching science and engineering "need-based learning". We have been applying this philosophy in…

Teaching Applied Genetics and Molecular Biology to Agriculture Engineers. Application of the European Credit Transfer System

ERIC Educational Resources Information Center

Weiss, J.; Egea-Cortines, M.

2008-01-01

We have been teaching applied molecular genetics to engineers and adapted the teaching methodology to the European Credit Transfer System. We teach core principles of genetics that are universal and form the conceptual basis of most molecular technologies. The course then teaches widely used techniques and finally shows how different techniques…

Measuring the Teaching Self-Efficacy of Science, Technology, Engineering, and Math Graduate Teaching Assistants

ERIC Educational Resources Information Center

DeChenne, Sue Ellen; Enochs, Larry

2010-01-01

An instrument to measure the teaching self-efficacy of science, technology, engineering, and mathematics (STEM) GTAs is adapted from a general college teaching instrument (Prieto Navarro, 2005) for the specific teaching environment of the STEM GTAs. The construct and content validity and reliability of the final instrument are indicated. The final…

Impact of Entrepreneurship Teaching in Higher Education on the Employability of Scientists and Engineers

ERIC Educational Resources Information Center

O'Leary, Simon

2012-01-01

This paper explores the impact effective entrepreneurship teaching has on the employability of scientists and engineers. Business teaching, guest speakers and work placements are part of many science and engineering degrees and this research indicates that entrepreneurship and related issues are also being addressed in a variety of ways and having…

Engineering for Liberal Arts and Engineering Students.

ERIC Educational Resources Information Center

The Weaver, 1986

1986-01-01

Describes courses designed to develop approaches for teaching engineering concepts, applied mathematics and computing skills to liberal arts undergraduates, and to teach the history of scientific and technological innovation and application to engineering and science majors. Discusses courses, course materials, enrichment activities, and…

A New Approach to Teaching Technical Subjects in Training Restoration Architects

ERIC Educational Resources Information Center

Pukharenko, Yurii Vladimirovich; Petrov, Vladimir Markovich; Norina, Natalia Vladimirovna; Norin, Veniamin Aleksandrovich

2017-01-01

The paper is devoted to teaching engineering subjects in the field of study "Restoration and renovation of architectural heritage." It demonstrates the necessity of changing the existing approach to teaching engineering design and construction to renovation architects. Based on our experience of teaching Building mechanics, we have…

Teaching Mathematics to Civil Engineers

ERIC Educational Resources Information Center

Sharp, J. J.; Moore, E.

1977-01-01

This paper outlines a technique for teaching a rigorous course in calculus and differential equations which stresses applicability of the mathematics to problems in civil engineering. The method involves integration of subject matter and team teaching. (SD)

Assessment of noise levels of the equipments used in the dental teaching institution, Bangalore.

PubMed

Kadanakuppe, Sushi; Bhat, Padma K; Jyothi, C; Ramegowda, C

2011-01-01

In dental practical classes, the acoustic environment is characterized by high noise levels in relation to other teaching areas, due to the exaggerated noise produced by some of these devices and use of dental equipment by many users at the same time. To measure, analyze and compare noise levels of equipments among dental learning areas under different working conditions and also to measure and compare noise levels between used and brand new handpieces under different working conditions. Noise levels were measured and analyzed in different dental learning areas that included clinical, pre-clinical areas and laboratories selected as representatives of a variety of learning-teaching activities. The noise levels were determined using a precision noise level meter (CENTER® 325 IEC 651 TYPE II) with a microphone. The mean of the maxima was determined. The data were collected, tabulated, and statistically analyzed using t tests. The noise levels measured varied between 64 and 97 dB(A).The differences in sound levels when the equipment was merely turned on and during cutting operations and also between used and brand new equipments were recorded. The laboratory engines had the highest noise levels, whereas the noise levels in high-speed turbine handpieces and the low-speed contra angle handpieces were decreased. The noise levels detected in this study are considered to be close to the limit of risk of hearing loss.

Faculty's Perceptions of Teaching Ethics and Leadership in Engineering Education

ERIC Educational Resources Information Center

AlSagheer, Abdullah; Al-Sagheer, Areej

2011-01-01

This paper addressed the faculty's perception of engineering ethics and leadership training. The study looks into the present state of and methodologies for teaching engineering ethics and leadership and aims to determine the faculty's perception of an identified gap in this aspect of engineering education. Engineering education has strong ethics…

Students' attitudes towards interdisciplinary education: a course on interdisciplinary aspects of science and engineering education

NASA Astrophysics Data System (ADS)

Gero, Aharon

2017-05-01

A course entitled 'Science and Engineering Education: Interdisciplinary Aspects' was designed to expose undergraduate students of science and engineering education to the attributes of interdisciplinary education which integrates science and engineering. The core of the course is an interdisciplinary lesson, which each student is supposed to teach his/her peers. Sixteen students at advanced stages of their studies attended the course. The research presented here used qualitative instruments to characterise students' attitudes towards interdisciplinary learning and teaching of science and engineering. According to the findings, despite the significant challenge which characterises interdisciplinary teaching, a notable improvement was evident throughout the course in the percentage of students who expressed willingness to teach interdisciplinary classes in future.

Race to improve student understanding of uncertainty: Using LEGO race cars in the physics lab

NASA Astrophysics Data System (ADS)

Parappilly, Maria; Hassam, Christopher; Woodman, Richard J.

2018-01-01

Laboratories using LEGO race cars were developed for students in an introductory physics topic with a high early drop-out rate. In a 2014 pilot study, the labs were offered to improve students' confidence with experiments and laboratory skills, especially uncertainty propagation. This intervention was extended into the intro level physics topic the next year, for comparison and evaluation. Considering the pilot study, we subsequently adapted the delivery of the LEGO labs for a large Engineering Mechanics cohort. A qualitative survey of the students was taken to gain insight into their perception of the incorporation of LEGO race cars into physics labs. For Engineering, the findings show that LEGO physics was instrumental in teaching students the measurement and uncertainty, improving their lab reporting skills, and was a key factor in reducing the early attrition rate. This paper briefly recalls the results of the pilot study, and how variations in the delivery yielded better learning outcomes. A novel method is proposed for how LEGO race cars in a physics lab can help students increase their understanding of uncertainty and motivate them towards physics practicals.

A plea for judgment.

PubMed

Davis, Michael

2012-12-01

Judgment is central to engineering, medicine, the sciences and many other practical activities. For example, one who otherwise knows what engineers know but lacks "engineering judgment" may be an expert of sorts, a handy resource much like a reference book or database, but cannot be a competent engineer. Though often overlooked or at least passed over in silence, the central place of judgment in engineering, the sciences, and the like should be obvious once pointed out. It is important here because it helps to explain where ethics fits into these disciplines. There is no good engineering, no good science, and so on without good judgment and no good judgment in these disciplines without ethics. Doing even a minimally decent job of teaching one of these disciplines necessarily includes teaching its ethics; teaching the ethics is teaching the discipline (or at least a large part of it).

Public health engineering education in India: current scenario, opportunities and challenges.

PubMed

Hussain, Mohammad Akhtar; Sharma, Kavya; Zodpey, Sanjay

2011-01-01

Public health engineering can play an important and significant role in solving environmental health issues. In order to confront public health challenges emerging out of environmental problems we need adequately trained public health engineers / environmental engineers. Considering the current burden of disease attributable to environmental factors and expansion in scope of applications of public health / environmental engineering science, it is essential to understand the present scenario of teaching, training and capacity building programs in these areas. Against this background the present research was carried out to know the current teaching and training programs in public health engineering and related disciplines in India and to understand the potential opportunities and challenges available. A systematic, predefined approach was used to collect and assemble the data related to various teaching and training programs in public health engineering / environmental engineering in India. Public health engineering / environmental engineering education and training in the country is mainly offered through engineering institutions, as pre-service and in-service training. Pre-service programs include diploma, degree (graduate) and post-graduate courses affiliated to various state technical boards, institutes and universities, whereas in-service training is mainly provided by Government of India recognized engineering and public health training institutes. Though trainees of these programs acquire skills related to engineering sciences, they significantly lack in public health skills. The teaching and training of public health engineering / environmental engineering is limited as a part of public health programs (MD Community Medicine, MPH, DPH) in India. There is need for developing teaching and training of public health engineering or environmental engineering as an interdisciplinary subject. Public health institutes can play an important and significant role in this regard by engaging themselves in initiating specialized programs in this domain.

Proceedings of the Undergraduate Mathematics Teaching Conference (Birmingham, England, September 3-6, 2001).

ERIC Educational Resources Information Center

Egerton, Patricia, Ed.

The 27th Undergraduate Mathematics Teaching Conference took place in September of 2001 at the University of Birmingham. Major topics of the conference included preparing a teaching portfolio, engineering mathematics should be taught by engineers, issues in teaching discrete mathematics, action research, study skills, and issues for web-delivered…

Teaching Teachers to Teach Green Engineering

ERIC Educational Resources Information Center

Flynn, Ann Marie; Naraghi, Mohammad H.; Austin, Nicole; Helak, Sean; Manzer, Jarrod

2006-01-01

The work provides guidelines for instructors who wish to incorporate green engineering concepts into a typical non-green engineering course without diluting course content or modifying the course syllabus by identifying 5 critical elements necessary to the successful integration of green engineering concepts into any traditional, design-oriented,…

Analysis of Engineering Content within Technology Education Programs

ERIC Educational Resources Information Center

Fantz, Todd D.; Katsioloudis, Petros J.

2011-01-01

In order to effectively teach engineering, technology teachers need to be taught engineering content, concepts, and related pedagogy. Some researchers posit that technology education programs may not have enough content to prepare technology teachers to teach engineering design. Certain technology teacher education programs have responded by…

Socialization Experiences Resulting from Doctoral Engineering Teaching Assistantships

ERIC Educational Resources Information Center

Mena, Irene B.; Diefes-Dux, Heidi A.; Capobianco, Brenda M.

2013-01-01

The purpose of this study was to explore and characterize the types of socialization experiences that result from engineering teaching assistantships. Using situated learning and communities of practice as the theoretical framework, this study highlights the experiences of 28 engineering doctoral students who worked as engineering teaching…

Teaching Engineering Design Using Computer Workstations.

ERIC Educational Resources Information Center

Hodgson, J. M.

1988-01-01

Explains the use of computer workstations in Electronic Engineering and in Control and Computer Engineering. Provides an introduction; initial teaching exercises at the first year, second, and third year design, research and development; and conclusions. (YP)

Student-driven courses on the social and ecological responsibilities of engineers : commentary on "student-inspired activities for the teaching and learning of engineering ethics".

PubMed

Baier, André

2013-12-01

A group of engineering students at the Technical University of Berlin, Germany, designed a course on engineering ethics. The core element of the developed Blue Engineering course are self-contained teaching-units, "building blocks". These building blocks typically cover one complex topic and make use of various teaching methods using moderators who lead discussions, rather than experts who lecture. Consequently, the students themselves started to offer the credited course to their fellow students who take an active role in further developing the course themselves.

Elementary Teachers' Views about Teaching Design, Engineering, and Technology

ERIC Educational Resources Information Center

Hsu, Ming-Chien; Purzer, Senay; Cardella, Monica E.

2011-01-01

While there is a growing interest in infusing engineering into elementary classrooms, very little is known about how well positioned elementary teachers are to teach engineering. This study examined elementary teachers' perceptions of and familiarity with design,engineering, and technology (DET). We collected data from 192 elementary teachers…

A Contemporary Preservice Technology Education Program

ERIC Educational Resources Information Center

Flanigan, Rod; Becker, Kurt; Stewardson, Gary

2012-01-01

In order to teach engineering education, today's engineering and technology education teachers must be equipped with lesson plans to teach engineering design, among other principles, to the 6th-12th grade levels. At Utah State University (USU), curriculum has been developed for preservice engineering and technology education teachers that…

Examining the Impact of Academic Development in the Engineering Faculties in Chile: Changes in Teaching Philosophy and Teachers' Competencies

ERIC Educational Resources Information Center

Acosta Peña, Roxana; Tomás-Folch, Marina; Feixas, Mònica

2017-01-01

The Faculties of Engineering Sciences at Universidad Católica del Norte in Chile regard teacher training as a necessary tool for its academics' professional development and as a fundamental way to improve their teaching quality. The Teaching Unit for Innovation in Engineering (UIDIN) has developed a new curriculum and training programme which…

The development and assessment of constructivist-based curriculum changes in a university general biology laboratory course

NASA Astrophysics Data System (ADS)

Herron, Sherry Shelton

1999-11-01

This study describes the processes involved in transforming the curriculum of the second semester general biology laboratory course for science majors, BSC 111L, at the University of Southern Mississippi from one based on the behaviorist model of teaching and learning to one based on the constructivist model. The study encompasses pilot and research phases. During the pilot phase conducted fall semester of 1997, the researcher presented to graduate teaching assistants an overview of the need for curriculum reform and some of the theoretical underpinnings for the movement. The researcher worked with all of the general biology teaching assistants to determine factors they considered supportive of the effort, identified specific goals and exercises, and developed a mission statement. The researcher then worked with two of the teaching assistants to write the new curriculum materials and pilot them in a designated laboratory section each week. During the research phase, the researcher facilitated the use of constructivist teaching methods and interviewed the teaching assistants during weekly group meetings. The researcher videotaped and observed the laboratories at various times throughout spring semester of 1998. Student responses to survey questions about the laboratories were collected during the observation sessions. Data derived from self-assessments on teaching beliefs completed by the teaching assistants, interview transcripts, videotaped laboratory sessions, and student surveys were used to assess the effectiveness of the new curriculum and the intervention program. It was observed that despite being given the same instructions, curriculum, and materials, each teaching assistant conducted his laboratory section in a unique way and rarely conducted the complete laboratory in the intended manner. It was also observed that one TA in particular needed more training in interpersonal skill development and content than was provided during the weekly intervention sessions. However, it was evident that constructivist teaching methods were being learned and that constructivist goals were being realized. Strengths and weaknesses of the curriculum materials were identified and extensive revisions were made by the researcher prior to the next semester. Finally, recommendations pertinent to the student survey used in this study (the Student Outcome Assessment Rubric) were made, and the need for more pedagogical instruction for teaching assistants and a mechanism to integrate lecture materials to the laboratory experience was described.

Aeronautical Engineering and Aerospace Engineering: A Learner-Centered Teaching Perspective in Higher Education

ERIC Educational Resources Information Center

Gohardani, Omid; Gohardani, Amir S.; Dokter, Erin; Macario, Kyla

2014-01-01

Teaching in the 21st century requires a modern teaching practice coherent with the evolutions of the Information Age. Interestingly, teaching practices have stretched beyond an art form and into the realm of science. Following these scientific trails, one can argue that one of the greatest challenges educators currently face is to maintain student…

Progress in reforming chemical engineering education.

PubMed

Wankat, Phillip C

2013-01-01

Three successful historical reforms of chemical engineering education were the triumph of chemical engineering over industrial chemistry, the engineering science revolution, and Engineering Criteria 2000. Current attempts to change teaching methods have relied heavily on dissemination of the results of engineering-education research that show superior student learning with active learning methods. Although slow dissemination of education research results is probably a contributing cause to the slowness of reform, two other causes are likely much more significant. First, teaching is the primary interest of only approximately one-half of engineering faculty. Second, the vast majority of engineering faculty have no training in teaching, but trained professors are on average better teachers. Significant progress in reform will occur if organizations with leverage-National Science Foundation, through CAREER grants, and the Engineering Accreditation Commission of ABET-use that leverage to require faculty to be trained in pedagogy.

INNOVATIONS IN EQUIPMENT AND TECHNIQUES FOR THE BIOLOGY TEACHING LABORATORY.

ERIC Educational Resources Information Center

BARTHELEMY, RICHARD E.; AND OTHERS

LABORATORY TECHNIQUES AND EQUIPMENT APPROPRIATE FOR TEACHING BIOLOGICAL SCIENCE CURRICULUM STUDY BIOLOGY ARE EMPHASIZED. MAJOR CATEGORIES INCLUDE (1) LABORATORY FACILITIES, (2) EQUIPMENT AND TECHNIQUES FOR CULTURE OF MICRO-ORGANISMS, (3) LABORATORY ANIMALS AND THEIR HOUSING, (4) TECHNIQUES FOR STUDYING PLANT GROWTH, (5) TECHNIQUES FOR STUDYING…

Teaching science, technology, and society to engineering students: a sixteen year journey.

PubMed

Ozaktas, Haldun M

2013-12-01

The course Science, Technology, and Society is taken by about 500 engineering students each year at Bilkent University, Ankara. Aiming to complement the highly technical engineering programs, it deals with the ethical, social, cultural, political, economic, legal, environment and sustainability, health and safety, reliability dimensions of science, technology, and engineering in a multidisciplinary fashion. The teaching philosophy and experiences of the instructor are reviewed. Community research projects have been an important feature of the course. Analysis of teaching style based on a multi-dimensional model is given. Results of outcome measurements performed for ABET assessment are provided. Challenges and solutions related to teaching a large class are discussed.

How to implement the Science Fair Self-Help Development Program in schools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menicucci, D.

1994-01-01

This manual is intended to act as a working guide for setting up a Science Fair Volunteer Support Committee at your school. The Science Fair Volunteer Support Committee, or SFVSC, is the key component of the Science Fair Self-Help program, which was developed by Sandia National Laboratories and is designed to support a school`s science activities. The SFVSC is a team of parents and community volunteers who work in concert with a school`s teaching staff to assist and manage all areas of a school Science and Engineering Fair. The main advantage of creating such a committee is that it freesmore » the science teachers from the organizational aspects of the fair and lets them concentrate on their job of teaching science. This manual is based on information gained through a Self-Help Development pilot program that was developed by Sandia National Laboratories during the 1991--92 school year at three Albuquerque, NM, middle schools. The manual describes the techniques that were successful in the pilot program and discusses how these techniques might be implemented in other schools. This manual also discusses problems that may be encountered, including suggestions for how they might be resolved.« less

The Laboratory is Vital in Science Instruction in the Secondary School.

ERIC Educational Resources Information Center

Klein, Sarah E.; And Others

1982-01-01

Presents the National Science Teachers Associations's (NSTA) position statement on the place of the laboratory in science education followed by other statements unique for teaching science in middle, junior, and senior high schools. Statements focus on teaching, research, and curriculum perspectives, laboratory's role, and laboratory's enhancement…

Integrating Laboratory Activity into a Junior High School Classroom

ERIC Educational Resources Information Center

Shyr, Wen-Jye

2010-01-01

This paper presents a wind power system laboratory activity and an outline for evaluating student performance in this activity. The work described here was to design and implement the laboratory to assist teachers in achieving the teaching objective of this activity. The laboratory teaching activities introduce energy sources, wind energy…

Coming to Terms with Engineering Design as Content

ERIC Educational Resources Information Center

Lewis, Theodore

2005-01-01

This article addresses the challenges posed by engineering design as a content area of technology education. What adjustments will technology teachers have to make in their approach to teaching and learning when they teach design as engineering in response to the new standards? How faithful to engineering as practiced must their approach be? There…

Improving the Practical Education of Chemical and Pharmaceutical Engineering Majors in Chinese Universities

ERIC Educational Resources Information Center

Zhao, Feng-qing; Yu, Yi-feng; Ren, Shao-feng; Liu, Shao-jie; Rong, Xin-yu

2014-01-01

Practical education in chemical engineering has drawn increasing attention in recent years. This paper discusses two approaches to teaching and learning about experiments among upper-level chemical and pharmaceutical engineering majors in China. On the basis of years of experience in teaching chemical and pharmaceutical engineering, we propose the…

The Engineering Design Process: Conceptions along the Learning-To-Teach Continuum

ERIC Educational Resources Information Center

Iveland, Ashley

2017-01-01

In this study, I sought to identify differences in the views and understandings of engineering design among individuals along the learning-to-teach continuum. To do so, I conducted a comprehensive review of literature to determine the various aspects of engineering design described in the fields of professional engineering and engineering…

The Use of Mini-projects in the Teaching of Geotechnics to Civil Engineering Undergraduates.

ERIC Educational Resources Information Center

Anderson, W. F.; And Others

1985-01-01

Geotechnics (which encompasses soil and rock mechanics, engineering geology, foundation design, and ground engineering methods) is a major component of virtually all civil engineering courses. Show how mini-projects are used to teach this subject. Format of projects, development of presentation skills, and assessment considerations are discussed.…

Computers in Engineering Teaching.

ERIC Educational Resources Information Center

Rushby, N. J.

This bibliography cites 26 books, papers, and reports dealing with various uses of computers in engineering education; and describes several computer programs available for use in teaching aeronautical, chemical, civil, electrical and electronic, mechanical, and nuclear engineering. Each computer program entry is presented by name, author,…

The impact of project-based learning on improving student learning outcomes of sustainability concepts in transportation engineering courses

NASA Astrophysics Data System (ADS)

Fini, Elham H.; Awadallah, Faisal; Parast, Mahour M.; Abu-Lebdeh, Taher

2018-05-01

This paper describes an intervention to enhance students' learning by involving students in brainstorming activities about sustainability concepts and their implications in transportation engineering. The paper discusses the process of incorporating the intervention into a transportation course, as well as the impact of this intervention on students' learning outcomes. To evaluate and compare students' learning as a result of the intervention, the Laboratory for Innovative Technology and Engineering Education survey instrument was used. The survey instrument includes five constructs: higher-order cognitive skills, self-efficacy, ease of learning subject matter, teamwork, and communication skills. Pre- and post-intervention surveys of student learning outcomes were conducted to determine the effectiveness of the intervention on enhancing students' learning outcomes. The results show that the implementation of the intervention significantly improved higher-order cognitive skills, self-efficacy, teamwork, and communication skills. Involving students in brainstorming activities related to sustainability concepts and their implications in transportation proved to be an effective teaching and learning strategy.

Metstoich--Teaching Quantitative Metabolism and Energetics in Biochemical Engineering

ERIC Educational Resources Information Center

Wong, Kelvin W. W.; Barford, John P.

2010-01-01

Metstoich, a metabolic calculator developed for teaching, can provide a novel way to teach quantitative metabolism to biochemical engineering students. It can also introduce biochemistry/life science students to the quantitative aspects of life science subjects they have studied. Metstoich links traditional biochemistry-based metabolic approaches…

The Experience of Teaching of Descriptive Geometry and Engineering Graphics in Russian Language as a Foreign Language

ERIC Educational Resources Information Center

Voronina, Marianna V.; Tretyakova, Zlata O.

2017-01-01

The article considers the peculiarities of training foreign students subject "Descriptive geometry and Engineering Graphics" in a modern engineering university of Russia. The relevance of the problem conditioned by the fact that virtually there are no special studies of teaching Descriptive Geometry and Engineering Graphics in Russian…

An Introduction of Finite Element Method in the Engineering Teaching at the University of Camaguey.

ERIC Educational Resources Information Center

Napoles, Elsa; Blanco, Ramon; Jimenez, Rafael; Mc.Pherson, Yoanka

This paper illuminates experiences related to introducing finite element methods (FEM) in mechanical and civil engineering courses at the University of Camaguey in Cuba and provides discussion on using FEM in postgraduate courses for industry engineers. Background information on the introduction of FEM in engineering teaching is focused on…

Iowa State University's undergraduate minor, online graduate certificate and resource center in NDE

NASA Astrophysics Data System (ADS)

Bowler, Nicola; Larson, Brian F.; Gray, Joseph N.

2014-02-01

Nondestructive evaluation is a `niche' subject that is not yet offered as an undergraduate or graduate major in the United States. The undergraduate minor in NDE offered within the College of Engineering at Iowa State University (ISU) provides a unique opportunity for undergraduate aspiring engineers to obtain a qualification in the multi-disciplinary subject of NDE. The minor requires 16 credits of course work within which a core course and laboratory in NDE are compulsory. The industrial sponsors of Iowa State's Center for Nondestructive Evaluation, and others, strongly support the NDE minor and actively recruit students from this pool. Since 2007 the program has graduated 10 students per year and enrollment is rising. In 2011, ISU's College of Engineering established an online graduate certificate in NDE, accessible not only to campus-based students but also to practicing engineers via the web. The certificate teaches the fundamentals of three major NDE techniques; eddy-current, ultrasonic and X-ray methods. This paper describes the structure of these programs and plans for development of an online, coursework-only, Master of Engineering in NDE and thesis-based Master of Science degrees in NDE.

This photocopy of an engineering drawing shows the floor plan ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

This photocopy of an engineering drawing shows the floor plan of the Liner Lab, including room functions. Austin, Field & Fry, Architects Engineers, 22311 West Third Street, Los Angeles 57, California: Edwards Test Station Complex Phase II, Jet Propulsion Laboratory, California Institute of Technology, Edwards Air Force Base, Edwards, California: "Liner Laboratory, Floor Plan and Schedules," drawing no. E33/4-2, 26 June 1962. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings of structures at JPL Edwards Facility. Drawings on file at JPL Plant Engineering, Pasadena, California. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings of structures at JPL Edwards Facility. Drawings on file at JPL Plant Engineering, Pasadena, California - Jet Propulsion Laboratory Edwards Facility, Liner Laboratory, Edwards Air Force Base, Boron, Kern County, CA

Using Case Studies in Calculus-based Physics

NASA Astrophysics Data System (ADS)

Katz, Debora M.

2006-12-01

Do your students believe that the physics only works in your classroom or laboratory? Or do they see that physics underlies their everyday experience? Case studies in physics help students connect physics principles to their everyday experience. For decades, case studies have been used to teach law, medicine and biology, but they are rarely used in physics. I am working on a calculus-based physics textbook for scientists and engineers. Case studies are woven into each chapter. Stop by and get a case study to test out in your classroom. I would love to get your feedback.

Growth and maintenance of Escherichia coli laboratory strains.

PubMed

Son, Mike S; Taylor, Ronald K

2012-11-01

Escherichia coli is a Gram-negative bacterium, commonly used in both teaching and research laboratories. This unit includes protocols for the growth and maintenance of E. coli in any teaching- or research-associated laboratory. © 2012 by John Wiley & Sons, Inc.

Micropipet manipulation of lipid membranes: Direct measurement of the material properties of a cohesive structure that is only two molecules thick

NASA Technical Reports Server (NTRS)

Needham, David

1993-01-01

The objectives are to demonstrate how we can make direct measurements of the mechanical properties of a special structure in biology, namely the lipid bilayer membrane, using a micromanipulation technique, and how these properties compare and contrast with 'more traditional' technological/engineering materials. Given that the investment in equipment and expertise to carry out these experiments is probably beyond the scope of most teaching labs, the described experiment is not intended as one that can actually be demonstrated in a student laboratory class. The intention behind presenting this work is to begin to raise awareness in the Material Science community about the material properties of biological material that form a new (to us) category of soft engineering materials that have dimensions on the nanoscale.

A Novel Patchwork Model Used in Lecture and Laboratory to Teach the Three-Dimensional Organization of Mesenteries

ERIC Educational Resources Information Center

Noel, Geoffroy P.J.C.

2013-01-01

Anatomy teaching is seeing a decline in both lecture and laboratory hours across many medical schools in North America. New strategies are therefore needed to not only make anatomy teaching more clinically integrated, but also to implement new interactive teaching techniques to help students more efficiently grasp the complex organization of the…

The Influence of Psychological Empowerment on the Enhancement of Chemistry Laboratory Demonstrators' Perceived Teaching Self-Image and Behaviours as Graduate Teaching Assistants

ERIC Educational Resources Information Center

Flaherty, A.; O'Dwyer, A.; Mannix-McNamara, P.; Leahy, J. J.

2017-01-01

Graduate students who fulfill teaching roles in the undergraduate laboratory play an important role in establishing a positive learning environment. A host of various graduate teacher training programmes have been developed, implemented and evaluated accordingly in order to enhance their teaching capability. In addition research has also…

Faux Mutagenesis: Teaching Troubleshooting through Controlled Failure

ERIC Educational Resources Information Center

Hartberg, Yasha

2006-01-01

By shifting pedagogical goals from obtaining successful mutations to teaching students critical troubleshooting skills, it has been possible to introduce site-directed mutagenesis into an undergraduate teaching laboratory. Described in this study is an inexpensive laboratory exercise in which students follow a slightly modified version of…

Statistical Analysis Tools for Learning in Engineering Laboratories.

ERIC Educational Resources Information Center

Maher, Carolyn A.

1990-01-01

Described are engineering programs that have used automated data acquisition systems to implement data collection and analyze experiments. Applications include a biochemical engineering laboratory, heat transfer performance, engineering materials testing, mechanical system reliability, statistical control laboratory, thermo-fluid laboratory, and a…

Part I: Virtual Laboratory versus Traditional Laboratory: Which Is More Effective for Teaching Electrochemistry? Part II: The Green Synthesis of Aurones Using a Deep Eutectic Solvent

ERIC Educational Resources Information Center

Hawkins, Ian C.

2013-01-01

The role of the teaching laboratory in science education has been debated over the last century. The goals and purposes of the laboratory are still debated and while most science educators consider laboratory a vital part of the education process, they differ widely on the purposes for laboratory and what methods should be used to teach…

Quality in Teaching Laboratories.

ERIC Educational Resources Information Center

Stubington, John F.

1995-01-01

Describes a Japanese process-oriented approach called KAIZEN for improving the quality of existing teaching laboratories. It provides relevant quality measurements and indicates how quality can be improved. Use of process criteria sidesteps the difficulty of defining quality for laboratory experiments and allows separation of student assessment…

Assessing Changes in Teachers' Attitudes toward Interdisciplinary STEM Teaching

ERIC Educational Resources Information Center

Al Salami, Mubarak K.; Makela, Carole J.; de Miranda, Michael A.

2017-01-01

Integrating engineering and technology concepts into K-12 science and math curricula through engineering design project-based learning has been found to increase students' interest in science, technology, engineering, and mathematics (STEM), however preparing teachers to shift to interdisciplinary teaching remains a significant challenge.…

The Teaching of Crystallography to Materials Scientists and Engineers.

ERIC Educational Resources Information Center

Wuensch, Bernhardt J.

1988-01-01

Provides a framework of the disciplines of materials science and engineering as they have developed. Discusses the philosophy, content, and approach to teaching these courses. Indicates the range of crystallographic topics contained in the materials science and engineering curriculum at the Massachussetts Institute of Technology. (CW)

Teaching Reform of Civil Engineering Materials Course Based on Project-Driven Pedagogy

NASA Astrophysics Data System (ADS)

Yidong, Xu; Wei, Chen; WeiguoJian, You; Jiansheng, Shen

2018-05-01

In view of the scattered experimental projects in practical courses of civil engineering materials, the poor practical ability of students and the disconnection between practical teaching and theoretical teaching, this paper proposes a practical teaching procedure. Firstly, the single experiment should be offered which emphasizes on improving the students’ basic experimental operating ability. Secondly, the compressive experiment is offered and the overall quality of students can be examined in the form of project team. In order to investigate the effect of teaching reform, the comparative analysis of the students of three grades (2014, 2015 and 2016) majored in civil engineering was conducted. The result shows that the students’ ability of experimental operation is obviously improved by using the project driven method-based teaching reform. Besides, the students’ ability to analyse and solve problems has also been improved.

Effectiveness of Podcasts Delivered on Mobile Devices as a Support for Student Learning during General Chemistry Laboratories

ERIC Educational Resources Information Center

Powell, Cynthia B.; Mason, Diana S.

2013-01-01

Chemistry instructors in teaching laboratories provide expert modeling of techniques and cognitive processes and provide assistance to enrolled students that may be described as scaffolding interaction. Such student support is particularly essential in laboratories taught with an inquiry-based curriculum. In a teaching laboratory with a high…

Tried and True: Tested Ideas for Teaching and Learning from the Regional Educational Laboratories.

ERIC Educational Resources Information Center

Levinson, Luna; Stonehill, Robert

This collection of 16 tested ideas for improving teaching and learning evolved from the work of the 1995 Proven Laboratory Practices Task Force charged with identifying and collecting the best and most useful work from the Regional Educational Laboratories. The Regional Educational Laboratory program is the largest research and development…

Using Teaching Portfolios to Revise Curriculum and Explore Instructional Practices of Technology and Engineering Education Teachers

ERIC Educational Resources Information Center

Lomask, Michal; Crismond, David; Hacker, Michael

2018-01-01

This paper reports on the use of teaching portfolios to assist in curriculum revision and the exploration of instructional practices used by middle school technology and engineering education teachers. Two new middle school technology and engineering education units were developed through the Engineering for All (EfA) project. One EfA unit focused…

Introducing Engineering Design to a Science Teaching Methods Course through Educational Robotics and Exploring Changes in Views of Preservice Elementary Teachers

ERIC Educational Resources Information Center

Kaya, Erdogan; Newley, Anna; Deniz, Hasan; Yesilyurt, Ezgi; Newley, Patrick

2017-01-01

Engineering has become an important subject in the Next Generation Science Standards (NGSS), which have raised engineering design to the same level as scientific inquiry when teaching science disciplines at all levels. Therefore, preservice elementary teachers (PSTs) need to know how to integrate the engineering design process (EDP) into their…

Mechanical Design of Spacecraft

NASA Technical Reports Server (NTRS)

1962-01-01

In the spring of 1962, engineers from the Engineering Mechanics Division of the Jet Propulsion Laboratory gave a series of lectures on spacecraft design at the Engineering Design seminars conducted at the California Institute of Technology. Several of these lectures were subsequently given at Stanford University as part of the Space Technology seminar series sponsored by the Department of Aeronautics and Astronautics. Presented here are notes taken from these lectures. The lectures were conceived with the intent of providing the audience with a glimpse of the activities of a few mechanical engineers who are involved in designing, building, and testing spacecraft. Engineering courses generally consist of heavily idealized problems in order to allow the more efficient teaching of mathematical technique. Students, therefore, receive a somewhat limited exposure to actual engineering problems, which are typified by more unknowns than equations. For this reason it was considered valuable to demonstrate some of the problems faced by spacecraft designers, the processes used to arrive at solutions, and the interactions between the engineer and the remainder of the organization in which he is constrained to operate. These lecture notes are not so much a compilation of sophisticated techniques of analysis as they are a collection of examples of spacecraft hardware and associated problems. They will be of interest not so much to the experienced spacecraft designer as to those who wonder what part the mechanical engineer plays in an effort such as the exploration of space.

Place Based STEM: Leveraging Local Resources to Engage K-12 Teachers in Teaching Integrated STEM and for Addressing the Local STEM Pipeline

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. Louis Nadelson; Anne Louise Seifert; Meagan McKinney

Business, industry, parks, nature settings, government infrastructure, and people, can be invaluable resources for connecting STEM curriculum within context which results in conditions ideal for promoting purposeful learning of authentic STEM content. Thus, community-based STEM resources offer ideal context for teaching STEM content. A benefit of focusing teacher attention on these contextual, content aligned resources is that they are in every community; making place-based STEM education a possibility, regardless of the location of STEM teaching and learning. Further, associating STEM teaching and learning with local resources addresses workforce development and the STEM pipeline by exposing students to STEM careers andmore » applications in their local communities. The desire to align STEM teaching and learning with local STEM related resources guided the design of our week-long integrated STEM K-12 teacher professional development (PD) program, i-STEM. We have completed four years of our i-STEM PD program and have made place-based STEM a major emphasis of our curriculum. This report focuses on the data collected in the fourth year of our program. Our week-long i-STEM PD served over 425 educators last summer (2013), providing them with in depth theme-based integrated STEM short courses which were limited to an average of 15 participants and whole group plenary sessions focused around placed based integrated STEM, inquiry, engineering design, standards and practices of Common Core and 21st Century skills. This state wide PD was distributed in five Idaho community colleges and took place over two weeks. The STEM short courses included topics on engineering for sustainability, using engineering to spark interest in STEM, municipal water systems, health, agriculture, food safety, mining, forestry, energy, and others. Integral to these short courses were field trips designed to connect the K-12 educators to the resources in their local communities that could be leveraged for teaching integrated STEM and provide a relevant context for teaching STEM content. Workplace presentations made by place-based STEM experts and provided teachers field trips to place-base STEM industries and business such as manufacturing plants, waste water treatment systems, mines, nature parks, food processing plants, research, hospitals, and laboratory facilities. We researched the 425 participants’ conceptions of place-based STEM prior to and after their taking part in the summer institutes, which included fieldtrips. Our findings revealed substantial increase in our participants’ knowledge, interest, and plans to use place-based resources for teaching integrated STEM. We detail the data analysis and provide a theoretical foundation and justification for the importance of place-based STEM to address the STEM pipeline for the future workforce.« less

Developing Teaching of Mathematics to First Year Engineering Students

ERIC Educational Resources Information Center

Jaworski, Barbara; Matthews, Janette

2011-01-01

Engineering Students Understanding Mathematics (ESUM) is a developmental research project at a UK university. The motivating aim is that engineering students should develop a more conceptual understanding of mathematics through their participation in an innovation in teaching. A small research team has both studied and contributed to innovation,…

The Impact of Teaching Communication Strategies on English Speaking of Engineering Undergraduates

ERIC Educational Resources Information Center

Kongsom, Tiwaporn

2016-01-01

This study investigates the impact of teaching communication strategies on Thai engineering undergraduate students' communication strategy use and strategic competence. Fifty-seven engineering undergraduate students were taught ten communication strategies for ten weeks and responded to a self-report communication strategy questionnaire before and…

Project-Based Teaching-Learning Computer-Aided Engineering Tools

ERIC Educational Resources Information Center

Simoes, J. A.; Relvas, C.; Moreira, R.

2004-01-01

Computer-aided design, computer-aided manufacturing, computer-aided analysis, reverse engineering and rapid prototyping are tools that play an important key role within product design. These are areas of technical knowledge that must be part of engineering and industrial design courses' curricula. This paper describes our teaching experience of…

Teaching Engineering Ethics with Sustainability as Context

ERIC Educational Resources Information Center

Byrne, Edmond P.

2012-01-01

Purpose: The purpose of this paper is to ascertain the engagement and response of students to the teaching of engineering ethics incorporating a macro ethical framework whereby sustainability is viewed as context to professional practice. This involves incorporating a broader conception of engineering than is typically applied in conventional…

Socialization Experiences Resulting from Engineering Teaching Assistantships at Purdue University

ERIC Educational Resources Information Center

Mena, Irene B.

2010-01-01

The purpose of this study was to explore and understand the types of socialization experiences that result from engineering teaching assistantships. Using situated learning as the theoretical framework and phenomenology as the methodological framework, this study highlights the experiences of 28 engineering doctoral students who worked as…

Diversity Issues in the Engineering Curriculum

ERIC Educational Resources Information Center

Ihsen, Susanne; Gebauer, Sabrina

2009-01-01

Teaching engineering studies students about diversity issues as part of the curriculum in engineering programs is an essential part of preparing the students for their professional life. By teaching them what this is and what it means for their (professional) lives sensitises them towards more responsibility. The idea is to connect diversity…

Why Research-Informed Teaching in Engineering Education? A Review of the Evidence

ERIC Educational Resources Information Center

Bubou, Gordon Monday; Offor, Ibebietei Temple; Bappa, Abubakar Saddiq

2017-01-01

Challenges of today's engineering education (EE) are emergent, necessitating calls for its reformation to empower future engineers function optimally as innovative leaders, in both local and international contexts. These challenges: keeping pace with technological dynamism; high attrition; and most importantly, quality teaching/learning require…

Teaching Continuum Mechanics in a Mechanical Engineering Program

ERIC Educational Resources Information Center

Liu, Yucheng

2011-01-01

This paper introduces a graduate course, continuum mechanics, which is designed for and taught to graduate students in a Mechanical Engineering (ME) program. The significance of continuum mechanics in engineering education is demonstrated and the course structure is described. Methods used in teaching this course such as topics, class…

Development of teaching modules for geology and engineering coursework using terrestrial LiDAR scanning systems

NASA Astrophysics Data System (ADS)

Yarbrough, L. D.; Katzenstein, K.

2012-12-01

Exposing students to active and local examples of physical geologic processes is beneficial to the learning process. Students typically respond with interest to examples that use state-of-the-art technologies to investigate local or regional phenomena. For lower cognitive level of learning (e.g. knowledge, comprehension, and application), the use of "close-to-home" examples ensures that students better understand concepts. By providing these examples, the students may already have a familiarity or can easily visit the location. Furthermore, these local and regional examples help students to offer quickly other examples of similar phenomena. Investigation of these examples using normal photographic techniques, as well as a more sophisticated 3-D Light Detection And Ranging (LiDAR) (AKA Terrestrial Laser Scanning or TLS) system, allows students to gain a better understanding of the scale and the mechanics of the geologic processes and hazards. The systems are used for research, teaching and outreach efforts and depending on departmental policies can be accessible to students are various learning levels. TLS systems can yield scans at sub-centimeter resolution and contain surface reflectance of targets. These systems can serve a number of learning goals that are essential for training geoscientists and engineers. While querying the data to answer geotechnical or geomorphologic related questions, students will develop skills using large, spatial databases. The upper cognitive level of learning (e.g. analysis, synthesis, and evaluation) is also promoted by using a subset of the data and correlating the physical geologic process of stream bank erosion and rock slope failures with mathematical and computer models using the scanned data. Students use the examples and laboratory exercises to help build their engineering judgment skills with Earth materials. The students learn not only applications of math and engineering science but also the economic and social implication of designed engineering solutions. These course learning modules were developed for traditional geological engineering courses delivered on campus, for more intensive field work courses and online-based asynchronous course delivery.

Sketching by Design: Teaching Sketching to Young Learners

ERIC Educational Resources Information Center

Kelley, Todd R.; Sung, Euisuk

2017-01-01

Recent science educational reforms in the United States have prompted increased efforts to teach engineering design as an approach to improve STEM (Science, Technology, Engineering, and Mathematics) learning in K-12 classrooms. Teaching design in early grades is a new endeavor for teachers in the United States. Much can be learned from design…

Developing Learning Tool of Control System Engineering Using Matrix Laboratory Software Oriented on Industrial Needs

NASA Astrophysics Data System (ADS)

Isnur Haryudo, Subuh; Imam Agung, Achmad; Firmansyah, Rifqi

2018-04-01

The purpose of this research is to develop learning media of control technique using Matrix Laboratory software with industry requirement approach. Learning media serves as a tool for creating a better and effective teaching and learning situation because it can accelerate the learning process in order to enhance the quality of learning. Control Techniques using Matrix Laboratory software can enlarge the interest and attention of students, with real experience and can grow independent attitude. This research design refers to the use of research and development (R & D) methods that have been modified by multi-disciplinary team-based researchers. This research used Computer based learning method consisting of computer and Matrix Laboratory software which was integrated with props. Matrix Laboratory has the ability to visualize the theory and analysis of the Control System which is an integration of computing, visualization and programming which is easy to use. The result of this instructional media development is to use mathematical equations using Matrix Laboratory software on control system application with DC motor plant and PID (Proportional-Integral-Derivative). Considering that manufacturing in the field of Distributed Control systems (DCSs), Programmable Controllers (PLCs), and Microcontrollers (MCUs) use PID systems in production processes are widely used in industry.

Teacher Research Programs = Increased Student Achievement

NASA Astrophysics Data System (ADS)

Dubner, J.

2011-12-01

Columbia University's Summer Research Program for Science Teachers (SRP), founded in 1990, is one of the largest, best known university professional development programs for science teachers in the U.S. For eight weeks in each of two consecutive summers, teachers participate as a member of a research team, led by a member of Columbia University's research faculty. In addition to the laboratory experience, all teachers meet weekly during the summer for a series of pedagogical activities to assist them in transferring the experience to their classrooms. The primary goal of the program is to provide K-12 science teachers with opportunities to work at the cutting edge of science and engineering, and thus to revitalize their teaching and help them to appreciate the use of inquiry-based methods in their classroom instruction. The secondary goals of the program are to give the pre-college teacher the ability to guide their students toward careers in science and engineering, to develop new teaching strategies, and to foster long-term scholarly collaborations. The last is especially important as it leads to a model of the teacher as active in science yet committed to the pre-college classroom. Since its inception, SRP has focused on an objective assessment of the program's impact on attitudes and instructional practices of participating teachers, on the performance of these teachers in their mentors' laboratories, and most importantly, on the impact of their participation in the program has on student interest and performance in science. Our research resulted in a paper published in the journal Science. SRP also facilitates a multi-site survey-based evaluation of other teacher research programs around the country. The author will present the findings of both studies.

Project-oriented teaching model about specialized courses in the information age

NASA Astrophysics Data System (ADS)

Chen, Xiaodong; Wang, Jinjiang; Tian, Qingguo; Wang, Yi; Cai, Huaiyu

2017-08-01

Specialized courses play a significant role in the usage of basic knowledge in the practical application for engineering college students. The engineering data available has sharply increased since the beginning of the information age in the 20th century, providing much more approaches to study and practice. Therefore, how to guide students to make full use of resources for active engineering practice learning has become one of the key problems for specialized courses. This paper took the digital image processing course for opto-electronic information science and technology major as an example, discussed the teaching model of specialized course in the information age, put forward the "engineering resource oriented model", and fostered the ability of engineering students to use the basic knowledge to innovate and deal with specific project objectives. The fusion of engineering examples into practical training and teaching encourages students to practice independent engineering thinking.

Integrating teaching and research in the field and laboratory settings

NASA Astrophysics Data System (ADS)

Wang, L.; Kaseke, K. F.; Daryanto, S.; Ravi, S.

2015-12-01

Field observations and laboratory measurements are great ways to engage students and spark students' interests in science. Typically these observations are separated from rigorous classroom teaching. Here we assessed the potential of integrating teaching and research in the field and laboratory setting in both US and abroad and worked with students without strong science background to utilize simple laboratory equipment and various environmental sensors to conduct innovative projects. We worked with students in Namibia and two local high school students in Indianapolis to conduct leaf potential measurements, soil nutrient extraction, soil infiltration measurements and isotope measurements. The experience showed us the potential of integrating teaching and research in the field setting and working with people with minimum exposure to modern scientific instrumentation to carry out creative projects.

Biomedical laboratory science education: standardising teaching content in resource-limited countries.

PubMed

Arneson, Wendy; Robinson, Cathy; Nyary, Bryan

2013-01-01

There is a worldwide shortage of qualified laboratory personnel to provide adequate testing for the detection and monitoring of diseases. In an effort to increase laboratory capacity in developing countries, new skills have been introduced into laboratory services. Curriculum revision with a focus on good laboratory practice is an important aspect of supplying entry-level graduates with the competencies needed to meet the current needs. Gaps in application and problem-solving competencies of newly graduated laboratory personnel were discovered in Ethiopia, Tanzania and Kenya. New medical laboratory teaching content was developed in Ethiopia, Tanzania and Kenya using national instructors, tutors, and experts and consulting medical laboratory educators from the United States of America (USA). Workshops were held in Ethiopia to create standardised biomedical laboratory science (BMLS) lessons based on recently-revised course objectives with an emphasis on application of skills. In Tanzania, course-module teaching guides with objectives were developed based on established competency outcomes and tasks. In Kenya, example interactive presentations and lesson plans were developed by the USA medical laboratory educators prior to the workshop to serve as resources and templates for the development of lessons within the country itself. The new teaching materials were implemented and faculty, students and other stakeholders reported successful outcomes. These approaches to updating curricula may be helpful as biomedical laboratory schools in other countries address gaps in the competencies of entry-level graduates.

Meeting the expectation of industry: an integrated approach for the teaching of mechanics and electronics to design students

NASA Astrophysics Data System (ADS)

Bingham, Guy A.; Southee, Darren J.; Page, Tom

2015-07-01

This paper examines the traditional engineering-based provision delivered to Product Design and Technology (B.Sc.) undergraduates at the Loughborough Design School and questions its relevancy against the increasing expectations of industry. The paper reviews final-year design projects to understand the level of transference of engineering-based knowledge into design practice and highlights areas of opportunity for improved teaching and learning. The paper discusses the development and implementation of an integrated approach to the teaching of Mechanics and Electronics to formalise and reinforce the key learning process of transference within the design context. The paper concludes with observations from the delivery of this integrated teaching and offers insights from student and academic perspectives for the further improvement of engineering-based teaching and learning.

A Research-Based Laboratory Course Designed to Strengthen the Research-Teaching Nexus

ERIC Educational Resources Information Center

Parra, Karlett J.; Osgood, Marcy P.; Pappas, Donald L., Jr.

2010-01-01

We describe a 10-week laboratory course of guided research experiments thematically linked by topic, which had an ultimate goal of strengthening the undergraduate research-teaching nexus. This undergraduate laboratory course is a direct extension of faculty research interests. From DNA isolation, characterization, and mutagenesis, to protein…

Learning to Teach Inquiry with ICT

ERIC Educational Resources Information Center

Tran, Trinh-Ba; van den Berg, Ed; Ellermeijer, Ton; Beishuizen, Jos

2018-01-01

Research has shown that the objectives for laboratory teaching--just as with other teaching methods--are often not achieved and that many laboratory sessions are ineffective and yet expensive in terms of pupil and teacher time, and facilities. There are several reasons for this, but one reason is that instructions for many lab activities are too…

The Effectiveness of Active and Traditional Teaching Techniques in the Orthopedic Assessment Laboratory

ERIC Educational Resources Information Center

Nottingham, Sara; Verscheure, Susan

2010-01-01

Active learning is a teaching methodology with a focus on student-centered learning that engages students in the educational process. This study implemented active learning techniques in an orthopedic assessment laboratory, and the effects of these teaching techniques. Mean scores from written exams, practical exams, and final course evaluations…

Introducing Quality Control in the Chemistry Teaching Laboratory Using Control Charts

ERIC Educational Resources Information Center

Schazmann, Benjamin; Regan, Fiona; Ross, Mary; Diamond, Dermot; Paull, Brett

2009-01-01

Quality control (QC) measures are less prevalent in teaching laboratories than commercial settings possibly owing to a lack of commercial incentives or teaching resources. This article focuses on the use of QC assessment in the analytical techniques of high performance liquid chromatography (HPLC) and ultraviolet-visible spectroscopy (UV-vis) at…

Exercise in Inquiry: Critical Thinking in an Inquiry-Based Exercise Physiology Laboratory Course.

ERIC Educational Resources Information Center

DiPasquale, Dana M.; Mason, Cheryl L.; Kolkhorst, Fred W.

2003-01-01

Describes an inquiry-based teaching method implemented in an undergraduate exercise physiology laboratory course. Indicates students' strong, positive feelings about the inquiry-based teaching method and shows that inquiry-based learning results in a higher order of learning not typically observed in traditional style classes. This teaching method…

Why and How We Made a Problem Oriented AV Teaching Unit for Chemistry Students.

ERIC Educational Resources Information Center

Mulder, T. H. M.; Verdonk, A. H.

1984-01-01

Describes an audiovisual teaching unit on the chemical laboratory technique of recrystallization which was developed along problem-solving lines and based on observation of student laboratory behavior. Discussion includes usual procedures for developing such units, how this unit solves problems typically associated with teaching, and its general…

Integrating teaching and authentic research in the field and laboratory settings

NASA Astrophysics Data System (ADS)

Daryanto, S.; Wang, L.; Kaseke, K. F.; Ravi, S.

2016-12-01

Typically authentic research activities are separated from rigorous classroom teaching. Here we assessed the potential of integrating teaching and research activities both in the field and in the laboratory. We worked with students from both US and abroad without strong science background to utilize advanced environmental sensors and statistical tool to conduct innovative projects. The students include one from Namibia and two local high school students in Indianapolis (through Project SEED, Summer Experience for the Economically Disadvantaged). They conducted leaf potential measurements, isotope measurements and meta-analysis. The experience showed us the great potential of integrating teaching and research in both field and laboratory settings.

Implementing Problem-Based Learning in Introductory Engineering Courses: A Qualitative Investigation of Facilitation Strategies

ERIC Educational Resources Information Center

Nicole Hunter, Deirdre-Annaliese

2015-01-01

Increasing pressure to transform teaching and learning of engineering is supported by mounting research evidence for the value of learner-centered pedagogies. Despite this evidence, engineering faculty are often unsuccessful in applying such teaching approaches often because they lack the necessary knowledge to customize these pedagogies for their…

Teaching Interview Skills to Undergraduate Engineers: An Emerging Area of Library Instruction

ERIC Educational Resources Information Center

Nelson, Megan Sapp

2009-01-01

Librarianship is one of a limited number of disciplines that deliberately learn and practice the art of the interview. For engineering librarians, this gives expertise and a role in teaching professional skills that are increasingly expected in the engineering profession. The reference interview and design interview have many similarities. Some…

Changing the Teaching/Learning Procedures in Physics for Agricultural Engineering. A Case Study

ERIC Educational Resources Information Center

Mulero, Angel; Parra, M. Isabel; Cachadina, Isidro

2012-01-01

The subject "Physical Fundamentals of Engineering" for agricultural engineers in the University of Extremadura has long had high rates of students not attending classes, not presenting for examinations and, finally, failing the subject. During the 2007 and 2008 courses, the teaching/learning procedures were strongly modified. Analysis of the…

Collaborating for Success: Team Teaching the Engineering Technical Thesis

ERIC Educational Resources Information Center

Keating, Terrence; Long, Mike

2012-01-01

This paper will examine the collaborative teaching process undertaken at College of the North Atlantic-Qatar (CNA-Q) by Engineering and the Communication faculties to improve the overall quality of engineering students' capstone projects known as the Technical Thesis. The Technical Thesis is divided into two separate components: a proposal stage…

Engineering Encounters: From STEM to STEAM

ERIC Educational Resources Information Center

Cook, Kristin; Bush, Sarah; Cox, Richard

2017-01-01

Teaching STEAM (science, technology, engineering, art, and math) in elementary school could be even more promising than teaching STEM. This is due to its ability to cross multiple subject areas and its appeal to multiple types of learners. Intentional integration of the arts in science and engineering lessons has the potential to more deeply…

Examining the Teaching of Science, and Technology and Engineering Content and Practices: An Instrument Modification Study

ERIC Educational Resources Information Center

Love, Tyler S.; Wells, John G.; Parkes, Kelly A.

2017-01-01

A modified Reformed Teaching Observation Protocol (RTOP) (Piburn & Sawada, 2000) instrument was used to separately examine eight technology and engineering (T&E) educators' teaching of science, and T&E content and practices, as called for by the "Standards for Technological Literacy: Content for the Study of Technology"…

Cause-Effect Analysis: Improvement of a First Year Engineering Students' Calculus Teaching Model

ERIC Educational Resources Information Center

van der Hoff, Quay; Harding, Ansie

2017-01-01

This study focuses on the mathematics department at a South African university and in particular on teaching of calculus to first year engineering students. The paper reports on a cause-effect analysis, often used for business improvement. The cause-effect analysis indicates that there are many factors that impact on secondary school teaching of…

Mapping Beliefs about Teaching to Patterns of Instruction within Science, Technology, Engineering, and Mathematics

ERIC Educational Resources Information Center

Allendoerfer, Cheryl; Wilson, Denise; Kim, Mee Joo; Burpee, Elizabeth

2014-01-01

In this paper, we identify beliefs about teaching and patterns of instruction valued and emphasized by science, technology, engineering, and mathematics faculty in higher education in the USA. Drawing on the notion that effective teaching is student-centered rather than teacher-centered and must include a balance of knowledge-, learner-,…

Student research laboratory for optical engineering

NASA Astrophysics Data System (ADS)

Tolstoba, Nadezhda D.; Saitgalina, Azaliya; Abdula, Polina; Butova, Daria

2015-10-01

Student research laboratory for optical engineering is comfortable place for student's scientific and educational activity. The main ideas of laboratory, process of creation of laboratory and also activity of laboratory are described in this article. At ITMO University in 2013-2014 were formed a lot of research laboratories. SNLO is a student research (scientific) laboratory formed by the Department of Applied and computer optics of the University ITMO (Information Technologies of Mechanics and Optics). Activity of laboratory is career guidance of entrants and students in the field of optical engineering. Student research laboratory for optical engineering is a place where student can work in the interesting and entertaining scientific atmosphere.

The chemistry teaching laboratory: The student perspective

NASA Astrophysics Data System (ADS)

Polles, John Steven

In this study, I investigated the Student/learner's experiences in the chemistry teaching laboratory and the meaning that she or he derived from these experiences. This study sought to answer these questions: (1) What was the students experience in the teaching laboratory?, (2) What aspects of the laboratory experience did the student value?, and (3) What beliefs did the student hold concerning the role of the laboratory experience in developing her or his understanding of chemistry? Students involved in an introductory chemistry course at Purdue University were asked to complete a two-part questionnaire consisting of 16 scaled response and 5 free response items, and 685 did so. Fourteen students also participated in a semi-structured individual interview. The questionnaire and interview were designed to probe the students' perceived experience and answer the above questions. I found that students possess strong conceptions of the laboratory experience: a pre-conception that colors their experience from the outset, and a post-conception that is a mix of positive and negative reflections. I also found that the learner deeply holds an implicit value in the laboratory experience. The other major finding was that the students' lived experience is dramatically shaped or influenced by external agencies, primarily the faculty (and by extension the teaching assistants). There is much debate in the extant literature over the learning value of the science teaching laboratory, but it is all from the perspective of faculty, curriculum designers, and administrators. This study adds the students' voice to the argument.

Chemistry teaching in the new degrees of Agricultural Engineering

NASA Astrophysics Data System (ADS)

Arce, Augusto; Tarquis, Ana Maria; Castellanos, Maria Teresa; Requejo, Maria Isabel; Cartagena, Maria Carmen

2013-04-01

The academic year 2011-12 is the second one implementing Bologna process in ETSI at the subjects of Agricultural Chemistry I and Chemistry II in the new four Degrees: Graduate in Engineering and Agricultural Science, Food Engineering Graduate, Graduate Environmental and engineering Graduate in Biotechnology, for it has been necessary to design and implement new interactive methodologies in the teaching-learning process based on the use of the virtual platform of the UPM, implement new evaluation systems that promote continued participation active student and the development of educational materials to support the subjects of chemistry designed new degrees within the EEES. In addition to the above actions, an assessment test prior chemistry knowledge has been made to all students who enter into Agricultural Grades, improving laboratory practices and the comparative study of academic obtained by the students of the new grades in the subjects of chemistry during the year 2011-12 compared to the 2010-11 academic year. More than 15,000 data have showed a good correlation between the student's prior knowledge, the level test performed, test scores, the overall success rate of the course and the abandonment of the different degrees. Academic results show a higher percentage of students enrolled and presented on a greater number of passes on students enrolled in the 2011-12 academic year for students enrolled in the previous academic year. The improved results have influenced the actions taken and the level of knowledge with students entering. Finally, we propose possible solutions to fix these results in future courses, aiming to improve the degree of efficiency, success and significant absenteeism in the first year as it will condition the dropout rate of these new degrees. Acknowledgements: Proyecto de Innovación Educativa N° IE02054-11/12 UPM. 2012.

Issues in undergraduate education in computational science and high performance computing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marchioro, T.L. II; Martin, D.

1994-12-31

The ever increasing need for mathematical and computational literacy within their society and among members of the work force has generated enormous pressure to revise and improve the teaching of related subjects throughout the curriculum, particularly at the undergraduate level. The Calculus Reform movement is perhaps the best known example of an organized initiative in this regard. The UCES (Undergraduate Computational Engineering and Science) project, an effort funded by the Department of Energy and administered through the Ames Laboratory, is sponsoring an informal and open discussion of the salient issues confronting efforts to improve and expand the teaching of computationalmore » science as a problem oriented, interdisciplinary approach to scientific investigation. Although the format is open, the authors hope to consider pertinent questions such as: (1) How can faculty and research scientists obtain the recognition necessary to further excellence in teaching the mathematical and computational sciences? (2) What sort of educational resources--both hardware and software--are needed to teach computational science at the undergraduate level? Are traditional procedural languages sufficient? Are PCs enough? Are massively parallel platforms needed? (3) How can electronic educational materials be distributed in an efficient way? Can they be made interactive in nature? How should such materials be tied to the World Wide Web and the growing ``Information Superhighway``?« less

Teaching Risk Analysis in an Aircraft Gas Turbine Engine Design Capstone Course

DTIC Science & Technology

2016-01-01

American Institute of Aeronautics and Astronautics 1 Teaching Risk Analysis in an Aircraft Gas Turbine Engine Design Capstone Course...development costs, engine production costs, and scheduling (Byerley A. R., 2013) as well as the linkage between turbine inlet temperature, blade cooling...analysis SE majors have studied and how this is linked to the specific issues they must face in aircraft gas turbine engine design. Aeronautical and

Real-time development of data acquisition and analysis software for hands-on physiology education in neuroscience: G-PRIME.

PubMed

Lott, Gus K; Johnson, Bruce R; Bonow, Robert H; Land, Bruce R; Hoy, Ronald R

2009-01-01

We report on the real-time creation of an application for hands-on neurophysiology in an advanced undergraduate teaching laboratory. Enabled by the rapid software development tools included in the Matlab technical computing environment (The Mathworks, Natick, MA), a team, consisting of a neurophysiology educator and a biophysicist trained as an electrical engineer, interfaced to a course of approximately 15 students from engineering and biology backgrounds. The result is the powerful freeware data acquisition and analysis environment, "g-PRIME." The software was developed from week to week in response to curriculum demands, and student feedback. The program evolved from a simple software oscilloscope, enabling RC circuit analysis, to a suite of tools supporting analysis of neuronal excitability and synaptic transmission analysis in invertebrate model systems. The program has subsequently expanded in application to university courses, research, and high school projects in the US and abroad as free courseware.

An exploration of the biomedical optics course construction of undergraduate biomedical engineering program in medical colleges

NASA Astrophysics Data System (ADS)

Guo, Shijun; Lyu, Jie; Zhang, Peiming

2017-08-01

In this paper, the teaching goals, teaching contents and teaching methods in biomedical optics course construction are discussed. From the dimension of teaching goals, students should master the principle of optical inspection on the human body, diagnosis and treatment of methodology and instruments, through the study of the theory and practice of this course, and can utilize biomedical optics methods to solve practical problems in the clinical medical engineering practice. From the dimension of teaching contents, based on the characteristics of biomedical engineering in medical colleges, the organic integration of engineering aspects, medical optical instruments, and biomedical aspects dispersed in human anatomy, human physiology, clinical medicine fundamental related to the biomedical optics is build. Noninvasive measurement of the human body composition and noninvasive optical imaging of the human body were taken as actual problems in biomedical optics fields. Typical medical applications such as eye optics and laser medicine were also integrated into the theory and practice teaching. From the dimension of teaching methods, referencing to organ-system based medical teaching mode, optical principle and instrument principle were taught by teachers from school of medical instruments, and the histological characteristics and clinical actual need in areas such as digestive diseases and urinary surgery were taught by teachers from school of basic medicine or clinical medicine of medical colleges. Furthermore, clinical application guidance would be provided by physician and surgeons in hospitals.

33 CFR 334.150 - Severn River at Annapolis, Md.; experimental test area, U.S. Navy Marine Engineering Laboratory.

Code of Federal Regulations, 2012 CFR

2012-07-01

....; experimental test area, U.S. Navy Marine Engineering Laboratory. 334.150 Section 334.150 Navigation and... Marine Engineering Laboratory. (a) The restricted area. The waters of Severn River shoreward of a line beginning at the southeasternmost corner of the U.S. Navy Marine Engineering Laboratory sea wall and running...

33 CFR 334.150 - Severn River at Annapolis, Md.; experimental test area, U.S. Navy Marine Engineering Laboratory.

Code of Federal Regulations, 2011 CFR

2011-07-01

....; experimental test area, U.S. Navy Marine Engineering Laboratory. 334.150 Section 334.150 Navigation and... Marine Engineering Laboratory. (a) The restricted area. The waters of Severn River shoreward of a line beginning at the southeasternmost corner of the U.S. Navy Marine Engineering Laboratory sea wall and running...

33 CFR 334.150 - Severn River at Annapolis, Md.; experimental test area, U.S. Navy Marine Engineering Laboratory.

Code of Federal Regulations, 2014 CFR

2014-07-01

....; experimental test area, U.S. Navy Marine Engineering Laboratory. 334.150 Section 334.150 Navigation and... Marine Engineering Laboratory. (a) The restricted area. The waters of Severn River shoreward of a line beginning at the southeasternmost corner of the U.S. Navy Marine Engineering Laboratory sea wall and running...

33 CFR 334.150 - Severn River at Annapolis, Md.; experimental test area, U.S. Navy Marine Engineering Laboratory.

Code of Federal Regulations, 2013 CFR

2013-07-01

....; experimental test area, U.S. Navy Marine Engineering Laboratory. 334.150 Section 334.150 Navigation and... Marine Engineering Laboratory. (a) The restricted area. The waters of Severn River shoreward of a line beginning at the southeasternmost corner of the U.S. Navy Marine Engineering Laboratory sea wall and running...

33 CFR 334.150 - Severn River at Annapolis, Md.; experimental test area, U.S. Navy Marine Engineering Laboratory.

Code of Federal Regulations, 2010 CFR

2010-07-01

....; experimental test area, U.S. Navy Marine Engineering Laboratory. 334.150 Section 334.150 Navigation and... Marine Engineering Laboratory. (a) The restricted area. The waters of Severn River shoreward of a line beginning at the southeasternmost corner of the U.S. Navy Marine Engineering Laboratory sea wall and running...

A low-cost computer-controlled Arduino-based educational laboratory system for teaching the fundamentals of photovoltaic cells

NASA Astrophysics Data System (ADS)

Zachariadou, K.; Yiasemides, K.; Trougkakos, N.

2012-11-01

We present a low-cost, fully computer-controlled, Arduino-based, educational laboratory (SolarInsight) to be used in undergraduate university courses concerned with electrical engineering and physics. The major goal of the system is to provide students with the necessary instrumentation, software tools and methodology in order to learn fundamental concepts of semiconductor physics by exploring the process of an experimental physics inquiry. The system runs under the Windows operating system and is composed of a data acquisition/control board, a power supply and processing boards, sensing elements, a graphical user interface and data analysis software. The data acquisition/control board is based on the Arduino open source electronics prototyping platform. The graphical user interface and communication with the Arduino are developed in C# and C++ programming languages respectively, by using IDE Microsoft Visual Studio 2010 Professional, which is freely available to students. Finally, the data analysis is performed by using the open source, object-oriented framework ROOT. Currently the system supports five teaching activities, each one corresponding to an independent tab in the user interface. SolarInsight has been partially developed in the context of a diploma thesis conducted within the Technological Educational Institute of Piraeus under the co-supervision of the Physics and Electronic Computer Systems departments’ academic staff.

Noise levels in the learning-teaching activities in a dental medicine school

NASA Astrophysics Data System (ADS)

Matos, Andreia; Carvalho, Antonio P. O.; Fernandes, Joao C. S.

2002-11-01

The noise levels made by different clinical handpieces and laboratory engines are considered to be the main descriptors of acoustical comfort in learning spaces in a dental medicine school. Sound levels were measured in five types of classrooms and teaching laboratories at the University of Porto Dental Medicine School. Handpiece noise measurements were made while instruments were running free and during operations with cutting tools (tooth, metal, and acrylic). Noise levels were determined using a precision sound level meter, which was positioned at ear level and also at one-meter distance from the operator. Some of the handpieces were brand new and the others had a few years of use. The sound levels encountered were between 60 and 99 dB(A) and were compared with the noise limits in A-weighted sound pressure level for mechanical equipments installed in educational buildings included in the Portuguese Noise Code and in other European countries codes. The daily personal noise exposure levels (LEP,d) of the students and professors were calculated to be between 85 and 90 dB(A) and were compared with the European legal limits. Some noise limits for this type of environment are proposed and suggestions for the improvement of the acoustical environment are given.

Ethics and engineering courses at Delft University of Technology: contents, educational setup and experiences.

PubMed

van de Poel, I R; Zandvoort, H; Brumsen, M

2001-04-01

This article reports on the development and teaching of compulsory courses on ethics and engineering at Delft University of Technology (DUT). Attention is paid to the teaching goals, the educational setup and methods, the contents of the courses, involvement of staff from engineering schools, experiences to date, and challenges for the future. The choices made with respect to the development and teaching of the courses are placed within the European and Dutch context and are compared and contrasted with the American situation and experiences.

Teaching Baroreflex Physiology to Medical Students: A Comparison of Quiz-Based and Conventional Teaching Strategies in a Laboratory Exercise

ERIC Educational Resources Information Center

Berg, Ronan M. G.; Plovsing, Ronni R.; Damgaard, Morten

2012-01-01

Quiz-based and collaborative teaching strategies have previously been found to be efficient for the improving meaningful learning of physiology during lectures. These approaches have, however, not been investigated during laboratory exercises. In the present study, we compared the impact of solving quizzes individually and in groups with…

Teaching Assistants' Perceptions of a Training to Support an Inquiry-Based General Chemistry Laboratory Course

ERIC Educational Resources Information Center

Wheeler, Lindsay B.; Maeng, Jennifer L.; Whitworth, Brooke A.

2015-01-01

The purpose of this qualitative investigation was to better understand teaching assistants' (TAs') perceptions of training in a guided inquiry undergraduate general chemistry laboratory context. The training was developed using existing TA training literature and informed by situated learning theory. TAs engaged in training prior to teaching (~25…

Bridging the Gap between Instructional and Research Laboratories: Teaching Data Analysis Software Skills through the Manipulation of Original Research Data

ERIC Educational Resources Information Center

Hansen, Sarah J. R.; Zhu, Jieling; Karch, Jessica M.; Sorrento, Cristina M.; Ulichny, Joseph C.; Kaufman, Laura J.

2016-01-01

The gap between graduate research and introductory undergraduate teaching laboratories is often wide, but the development of teaching activities rooted within the research environment offers an opportunity for undergraduate students to have first-hand experience with research currently being conducted and for graduate students to develop…

The Effect of Simulation-Assisted Laboratory Applications on Pre-Service Teachers' Attitudes towards Science Teaching

ERIC Educational Resources Information Center

Ulukök, Seyma; Sari, Ugur

2016-01-01

In this study, the effects of computer-assisted laboratory applications on pre-service science teachers' attitudes towards science teaching were investigated and the opinions of the pre-service teachers about the application were also determined. The study sample consisted of 46 students studying science teaching Faculty of Education. The study…

Promoting Inquiry-Based Teaching in Laboratory Courses: Are We Meeting the Grade?

ERIC Educational Resources Information Center

Beck, Christopher; Butler, Amy; Burke da Silva, Karen

2014-01-01

Over the past decade, repeated calls have been made to incorporate more active teaching and learning in undergraduate biology courses. The emphasis on inquiry-based teaching is especially important in laboratory courses, as these are the courses in which students are applying the process of science. To determine the current state of research on…

Directed Self-Inquiry: A Scaffold for Teaching Laboratory Report Writing

ERIC Educational Resources Information Center

Deiner, L. Jay; Newsome, Daniel; Samaroo, Diana

2012-01-01

A scaffold was created for the explicit instruction of laboratory report writing. The scaffold breaks the laboratory report into sections and teaches students to ask and answer questions in order to generate section-appropriate content and language. Implementation of the scaffold is done through a series of section-specific worksheets that are…

Student Reciprocal Peer Teaching as a Method for Active Learning: An Experience in an Electrotechnical Laboratory

NASA Astrophysics Data System (ADS)

Muñoz-García, Miguel A.; Moreda, Guillermo P.; Hernández-Sánchez, Natalia; Valiño, Vanesa

2013-10-01

Active learning is one of the most efficient mechanisms for learning, according to the psychology of learning. When students act as teachers for other students, the communication is more fluent and knowledge is transferred easier than in a traditional classroom. This teaching method is referred to in the literature as reciprocal peer teaching. In this study, the method is applied to laboratory sessions of a higher education institution course, and the students who act as teachers are referred to as "laboratory monitors." A particular way to select the monitors and its impact in the final marks is proposed. A total of 181 students participated in the experiment, experiences with laboratory monitors are discussed, and methods for motivating and training laboratory monitors and regular students are proposed. The types of laboratory sessions that can be led by classmates are discussed. This work is related to the changes in teaching methods in the Spanish higher education system, prompted by the Bologna Process for the construction of the European Higher Education Area

Integrating Engineering into Delaware's K-5 Classrooms: A Study of Pedagogical and Curricular Resources

ERIC Educational Resources Information Center

Grusenmeyer, Linda Huey

2017-01-01

This study examines the personal and curricular resources available to Delaware's elementary teachers during a time of innovative curriculum change, i.e., their knowledge, goals and beliefs regarding elementary engineering curriculum and the pedagogical support to teach two Science and Engineering Practices provided by science teaching materials.…

Elementary Teacher Self-Efficacy in Engineering and Student Achievement in Math and Science

ERIC Educational Resources Information Center

Gorena, Jacquelyn L.

2015-01-01

STEM education is a national priority, and more schools are implementing STEM K-12. Elementary teachers are prepared to teach science, mathematics, and technology, but teachers may not feel as prepared to teach engineering. Engineering is a new genre for elementary schools, and it is not typically a content area included in teacher preparation…

Instructional Strategies in Teaching Engineering at a Distance: Faculty Perspective

ERIC Educational Resources Information Center

Ariadurai, S. Anbahan; Manohanthan, Rajalingam

2008-01-01

This paper presents research on a convenience sample of the Open University of Sri Lanka's engineering faculty. Examined in this research are faculty's opinions on the instructional strategies they use to teach engineering courses at a distance. First, this paper details the pedagogical strategies used by the faculty, which is then followed by an…

The Use of a Parametric Feature Based CAD System to Teach Introductory Engineering Graphics.

ERIC Educational Resources Information Center

Howell, Steven K.

1995-01-01

Describes the use of a parametric-feature-based computer-aided design (CAD) System, AutoCAD Designer, in teaching concepts of three dimensional geometrical modeling and design. Allows engineering graphics to go beyond the role of documentation and communication and allows an engineer to actually build a virtual prototype of a design idea and…

A Case for the Need of Using Scaffolding Methods in Teaching Introductory, Fundamental Engineering Mechanics Classes

ERIC Educational Resources Information Center

Boylan-Ashraf, Peggy C.; Freeman, Steven A.; Shelley, Mack C.

2015-01-01

In the past ten years, engineering classrooms have seen an exponential growth in the use of technology, more than during any other previous decade. Unprecedented advancements, such as the advent of innovative gadgets and fundamental instructional alterations in engineering classrooms, have introduced changes in both teaching and learning. Student…

Integrator Element as a Promoter of Active Learning in Engineering Teaching

ERIC Educational Resources Information Center

Oliveira, Paulo C.; Oliveira, Cristina G.

2014-01-01

In this paper, we present a teaching proposal used in an Introductory Physics course to civil engineering students from Porto's Engineering Institute/Instituto Superior de Engenharia do Porto (ISEP). The proposal was born from the need to change students' perception and motivation for learning physics. It consists in the use of an integrator…

Characterizing Elementary Teachers' Enactment of High-Leverage Practices through Engineering Design-Based Science Instruction

ERIC Educational Resources Information Center

Capobianco, Brenda M.; DeLisi, Jacqueline; Radloff, Jeffrey

2018-01-01

In an effort to document teachers' enactments of new reform in science teaching, valid and scalable measures of science teaching using engineering design are needed. This study describes the development and testing of an approach for documenting and characterizing elementary science teachers' multiday enactments of engineering design-based science…

On-Line Role-Play as a Teaching Method in Engineering Studies

ERIC Educational Resources Information Center

Cobo, Adolfo; Conde, Olga Ma.; Quintela, Ma. Ángeles; Mirapéix, Jesús Ma.; López-Higuera, José Miguel

2011-01-01

In this paper we propose adapting role-play teaching methodology to engineering studies. The role of a maintenance technician, a relevant job profile for engineering graduates is has chosen. The interaction is based on email exchange, with the instructor included in the simulation to help guide the activity and achieve learning objectives. In this…

A Case Study: Teaching Engineering Concepts in Science. Research in Engineering and Technology Education

ERIC Educational Resources Information Center

Stricker, David R.

2010-01-01

This study was conducted to describe a teacher developed high school engineering course, to identify teaching strategies used in the process of delivering math and science literacy through this course, to identify challenges and constraints that occurred during its development and delivery, and to describe the strategies that were used to overcome…

www.teld.net: Online Courseware Engine for Teaching by Examples and Learning by Doing.

ERIC Educational Resources Information Center

Huang, G. Q.; Shen, B.; Mak, K. L.

2001-01-01

Describes TELD (Teaching by Examples and Learning by Doing), a Web-based online courseware engine for higher education. Topics include problem-based learning; project-based learning; case methods; TELD as a Web server; course materials; TELD as a search engine; and TELD as an online virtual classroom for electronic delivery of electronic…

Starting and Teaching Basic Robotics in the Classroom: Modern, Engaging Engineering in Technology Education

ERIC Educational Resources Information Center

Bianco, Andrew S.

2014-01-01

All technology educators have favorite lessons and projects that they most desire to teach. Many teachers might ask why teach robotics when there are many other concepts to cover with the students? The answer to this question is to engage students in science, technology, engineering, and math (commonly referred to as STEM) concepts. In order for…

Explore the Human-Based Teaching for the Professional Course of Materials Science and Engineering

ERIC Educational Resources Information Center

Zhao, Yiping; Chen, Li; Zhang, Yufeng

2008-01-01

As viewed from two sides such as teacher and student, in this article, we explore the human-based teaching reform for the college professional course of materials Science and Engineering, point out the qualities and conditions that professional teacher should possess in the process of human-based teaching reform of professional course and the…

Teaching English Engineering Terminology in a Hypermedia Environment.

ERIC Educational Resources Information Center

Stamison-Atmatzidi, M.; And Others

1995-01-01

Discusses a hypermedia prototype system constituting a hypermedia dictionary environment and a database of field-specific reading passages with related exercises, for utilization in the teaching of English engineering terminology in foreign language environments. (eight references) (CK)

Towards a controlled vocabulary on software engineering education

NASA Astrophysics Data System (ADS)

Pizard, Sebastián; Vallespir, Diego

2017-11-01

Software engineering is the discipline that develops all the aspects of the production of software. Although there are guidelines about what topics to include in a software engineering curricula, it is usually unclear which are the best methods to teach them. In any science discipline the construction of a classification schema is a common approach to understand a thematic area. This study examines previous publications in software engineering education to obtain a first controlled vocabulary (a more formal definition of a classification schema) in the field. Publications from 1988 to 2014 were collected and processed using automatic clustering techniques and the outcomes were analysed manually. The result is an initial controlled vocabulary with a taxonomy form with 43 concepts that were identified as the most used in the research publications. We present the classification of the concepts in three facets: 'what to teach', 'how to teach' and 'where to teach' and the evolution of concepts over time.

Medical imaging education in biomedical engineering curriculum: courseware development and application through a hybrid teaching model.

PubMed

Zhao, Weizhao; Li, Xiping; Chen, Hairong; Manns, Fabrice

2012-01-01

Medical Imaging is a key training component in Biomedical Engineering programs. Medical imaging education is interdisciplinary training, involving physics, mathematics, chemistry, electrical engineering, computer engineering, and applications in biology and medicine. Seeking an efficient teaching method for instructors and an effective learning environment for students has long been a goal for medical imaging education. By the support of NSF grants, we developed the medical imaging teaching software (MITS) and associated dynamic assessment tracking system (DATS). The MITS/DATS system has been applied to junior and senior medical imaging classes through a hybrid teaching model. The results show that student's learning gain improved, particularly in concept understanding and simulation project completion. The results also indicate disparities in subjective perception between junior and senior classes. Three institutions are collaborating to expand the courseware system and plan to apply it to different class settings.

Exploring Engineering instructors' views about writing and online tools to support communication in Engineering

NASA Astrophysics Data System (ADS)

Howard, Sarah K.; Khosronejad, Maryam; Calvo, Rafael A.

2017-11-01

To be fully prepared for the professional workplace, Engineering students need to be able to effectively communicate. However, there has been a growing concern in the field about students' preparedness for this aspect of their future work. It is argued that online writing tools, to engage numbers of students in the writing process, can support feedback on and development of writing in engineering on a larger scale. Through interviews and questionnaires, this study explores engineering academics' perceptions of writing to better understand how online writing tools may be integrated into their teaching. Results suggest that writing is viewed positively in the discipline, but it is not believed to be essential to success in engineering. Online writing tools were believed to support a larger number of students, but low knowledge of the tools limited academics' understanding of their usefulness in teaching and learning. Implications for innovation in undergraduate teaching are discussed.

32 CFR 555.2 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Experiment Station (WES), the U.S. Army Construction Engineering Research Laboratory (CERL), the U.S. Army Engineer Topographic Laboratories (ETL), the U.S. Army Coastal Engineering Research Center (CERC), the U.S... CEMETERIES CORPS OF ENGINEERS, RESEARCH AND DEVELOPMENT, LABORATORY RESEARCH AND DEVELOPMENT AND TESTS, WORK...

Biomedical laboratory science education: standardising teaching content in resource-limited countries

PubMed Central

Robinson, Cathy; Nyary, Bryan

2013-01-01

Background There is a worldwide shortage of qualified laboratory personnel to provide adequate testing for the detection and monitoring of diseases. In an effort to increase laboratory capacity in developing countries, new skills have been introduced into laboratory services. Curriculum revision with a focus on good laboratory practice is an important aspect of supplying entry-level graduates with the competencies needed to meet the current needs. Objectives Gaps in application and problem-solving competencies of newly graduated laboratory personnel were discovered in Ethiopia, Tanzania and Kenya. New medical laboratory teaching content was developed in Ethiopia, Tanzania and Kenya using national instructors, tutors, and experts and consulting medical laboratory educators from the United States of America (USA). Method Workshops were held in Ethiopia to create standardised biomedical laboratory science (BMLS) lessons based on recently-revised course objectives with an emphasis on application of skills. In Tanzania, course-module teaching guides with objectives were developed based on established competency outcomes and tasks. In Kenya, example interactive presentations and lesson plans were developed by the USA medical laboratory educators prior to the workshop to serve as resources and templates for the development of lessons within the country itself. Results The new teaching materials were implemented and faculty, students and other stakeholders reported successful outcomes. Conclusions These approaches to updating curricula may be helpful as biomedical laboratory schools in other countries address gaps in the competencies of entry-level graduates. PMID:29043162

The Role of the National Laboratory in Improving Secondary Science Education

DOE Office of Scientific and Technical Information (OSTI.GOV)

White,K.; Morris, M.; Stegman, M.

While the role of science, technology, engineering, and mathematics (STEM) teachers in our education system is obvious, their role in our economic and national security system is less so. Our nation relies upon innovation and creativity applied in a way that generates new technologies for industry, health care, and the protection of our national assets and citizens. Often, it is our science teachers who generate the excitement that leads students to pursue science careers. While academia provides these teachers with the tools to educate, the rigors of a science and technology curriculum, coupled with the requisite teaching courses, often limitmore » teacher exposure to an authentic research environment. As the single largest funding agency for the physical sciences, the US Department of Energy's (DOE) Office of Science plays an important role in filling this void. For STEM teachers, the DOE Academies Creating Teacher Scientists program (ACTS) bridges the worlds of research and education. The ACTS program at Brookhaven National Laboratory (BNL), one of several across the country, exemplifies the value of this program for participating teachers. Outcomes of the work at BNL as evidenced by the balance of this report, include the following: (1) Teachers have developed long-term relationships with the Laboratory through participation in ongoing research, and this experience has both built enthusiasm for and enriched the content knowledge of the participants. (2) Teachers have modified the way they teach and are more likely to engage students in authentic research and include more inquiry-based activities. (3) Teachers have reported their students are more interested in becoming involved in science through classes, extra-curricular clubs, and community involvement. (4) Teachers have established leadership roles within their peer groups, both in their own districts and in the broader teaching community. National laboratories are making an important contribution to the science education system by engaging teachers in authentic research activities, maintaining durable relationships with the teachers, sharing the tools and intellectual capabilities of a federal research agency, and taking the added step of engaging their students as well. These experiences, set in a scientifically rich environment, distinguish the DOE ACTS program.« less

Software Engineering Laboratory Series: Proceedings of the Twentieth Annual Software Engineering Workshop

NASA Technical Reports Server (NTRS)

1995-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Software Engineering Laboratory Series: Collected Software Engineering Papers. Volume 15

NASA Technical Reports Server (NTRS)

1997-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Software Engineering Laboratory Series: Collected Software Engineering Papers. Volume 14

NASA Technical Reports Server (NTRS)

1996-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Software Engineering Laboratory Series: Collected Software Engineering Papers. Volume 13

NASA Technical Reports Server (NTRS)

1995-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Laboratory 3.0: Manufacturing Technologies Laboratory Virtualization with a Student-Centred Methodology

ERIC Educational Resources Information Center

Fabregat-Sanjuan, Albert; Pàmies-Vilà, Rosa; Ferrando Piera, Francesc; De la Flor López, Silvia

2017-01-01

This paper presents a blended-learning strategy for improving the teaching method applied in the laboratory subject Manufacturing Technologies. The teaching method has been changed from a predominantly teacher-centred to an active learning system with a student-centred focus and e-learning activities. In face-to-face classes, a game-based learning…

Fostering Elementary School Students' Understanding of Simple Electricity by Combining Simulation and Laboratory Activities

ERIC Educational Resources Information Center

Jaakkola, T.; Nurmi, S.

2008-01-01

Computer simulations and laboratory activities have been traditionally treated as substitute or competing methods in science teaching. The aim of this experimental study was to investigate if it would be more beneficial to combine simulation and laboratory activities than to use them separately in teaching the concepts of simple electricity. Based…

A Survey of the Practices, Procedures, and Techniques in Undergraduate Organic Chemistry Teaching Laboratories

ERIC Educational Resources Information Center

Martin, Christopher B.; Schmidt, Monica; Soniat, Michael

2011-01-01

A survey was conducted of four-year institutions that teach undergraduate organic chemistry laboratories in the United States. The data include results from over 130 schools, describes the current practices at these institutions, and discusses the statistical results such as the scale of the laboratories performed, the chemical techniques applied,…

Creating the learning situation to promote student deep learning: Data analysis and application case

NASA Astrophysics Data System (ADS)

Guo, Yuanyuan; Wu, Shaoyan

2017-05-01

How to lead students to deeper learning and cultivate engineering innovative talents need to be studied for higher engineering education. In this study, through the survey data analysis and theoretical research, we discuss the correlation of teaching methods, learning motivation, and learning methods. In this research, we find that students have different motivation orientation according to the perception of teaching methods in the process of engineering education, and this affects their choice of learning methods. As a result, creating situations is critical to lead students to deeper learning. Finally, we analyze the process of learning situational creation in the teaching process of «bidding and contract management workshops». In this creation process, teachers use the student-centered teaching to lead students to deeper study. Through the study of influence factors of deep learning process, and building the teaching situation for the purpose of promoting deep learning, this thesis provide a meaningful reference for enhancing students' learning quality, teachers' teaching quality and the quality of innovation talent.

A flipped mode teaching approach for large and advanced electrical engineering courses

NASA Astrophysics Data System (ADS)

Ravishankar, Jayashri; Epps, Julien; Ambikairajah, Eliathamby

2018-05-01

A fully flipped mode teaching approach is challenging for students in advanced engineering courses, because of demanding pre-class preparation load, due to the complex and analytical nature of the topics. When this is applied to large classes, it brings an additional complexity in terms of promoting the intended active learning. This paper presents a novel selective flipped mode teaching approach designed for large and advanced courses that has two aspects: (i) it provides selective flipping of a few topics, while delivering others in traditional face-to-face teaching, to provide an effective trade-off between the two approaches according to the demands of individual topics and (ii) it introduces technology-enabled live in-class quizzes to obtain instant feedback and facilitate collaborative problem-solving exercises. The proposed approach was implemented for a large fourth year course in electrical power engineering over three successive years and the criteria for selecting between the flipped mode teaching and traditional teaching modes are outlined. Results confirmed that the proposed approach improved both students' academic achievements and their engagement in the course, without overloading them during the teaching period.

Cognition and thinking on Applied Optics course's reformation and innovation

NASA Astrophysics Data System (ADS)

Chen, Jingjing; Ji, Feng; Liu, Zhijian; Xia, Haojie; Shu, Shuangbao

2017-08-01

The course of "Applied Optics" is professional and foundational for the specialty of photo-electric information and engineering. According to the characteristics of the specialty, the teaching contents, teaching means, innovations and appraisal methods are mainly discussed in this paper. Firstly, one of the most difficult part to comprehend, the Fermat principle is taken as an example in the teaching content. By using the development history of optics and interesting natural phenomenon, students' understanding of the optical knowledge can be enhanced. Secondly, in various means of teaching art, ZEMAX provides students with a platform of training innovative consciousness and engineering capacity, and it make high cohesion in teaching and scientific research. Thirdly, in the teaching innovation, photoelectric contest can stimulate students' innovative thinking, innovation awareness, and cultivate undergraduate students' optics, mechanics, electricity, numerology integrated design capabilities. Lastly, the reform in the appraisal methods guide students from focusing on the examination results to pay attention to the learning process. Eventually, students' study interest has improved, demand of the engineering practice has adapted, and the well teaching effect has realized.

Design-Build-Write: Increasing the Impact of English for Specific Purposes Learning and Teaching in Aeronautical Engineering Education through Multiple Intelligences Task Design

ERIC Educational Resources Information Center

Tatzl, Dietmar

2011-01-01

This article presents an English for Specific Purposes (ESP) task developed for teaching aeronautical engineering students. The task Design-Build-Write rests on the assumption that engineering students are skilled at mathematical reasoning, problem solving, drawing and constructing. In Gardner's 1983 Multiple Intelligences (MI) theory, these…

Constructively Aligned Teaching and Learning in Higher Education in Engineering: What Do Students Perceive as Contributing to the Learning of Interdisciplinary Thinking?

ERIC Educational Resources Information Center

Spelt, E. J. H.; Luning, P. A.; van Boekel, M. A. J. S.; Mulder, M.

2015-01-01

Increased attention to the need for constructively aligned teaching and learning in interdisciplinary higher education in engineering is observed. By contrast, little research has been conducted on the implementation of the outcome-based pedagogical approach to interdisciplinary higher education in engineering. Therefore, the present design-based…

'To Go Boldly': Teaching Science Fiction to First-Year Engineering Students in a South African Context

ERIC Educational Resources Information Center

Manià, Kirby; Mabin, Linda Kathleen; Liebenberg, Jessica

2018-01-01

This paper reflects on the teaching of science fiction texts to first-year engineering students at the University of the Witwatersrand as part of a Critical Thinking course that uses literature as a vehicle through which to develop competence in critical literacy and communication. This course aims to equip engineering students, as future…

The Effect of Case Teaching on Meaningful and Retentive Learning When Studying Genetic Engineering

ERIC Educational Resources Information Center

Güccük, Ahmet; Köksal, Mustafa Serdar

2017-01-01

The purpose of this study is to investigate the effects of case teaching on how students learn about genetic engineering, in terms of meaningful learning and retention of learning. The study was designed as quasi-experimental research including 63 8th graders (28 boys and 35 girls). To collect data, genetic engineering achievement tests were…

From Biology to Mathematical Models and Back: Teaching Modeling to Biology Students, and Biology to Math and Engineering Students

ERIC Educational Resources Information Center

Chiel, Hillel J.; McManus, Jeffrey M.; Shaw, Kendrick M.

2010-01-01

We describe the development of a course to teach modeling and mathematical analysis skills to students of biology and to teach biology to students with strong backgrounds in mathematics, physics, or engineering. The two groups of students have different ways of learning material and often have strong negative feelings toward the area of knowledge…

Teaching Embryology without Lectures and without Traditional Laboratories--An Adventure in Innovation.

ERIC Educational Resources Information Center

Heady, Judith E.

1993-01-01

Describes problems with teaching embryology in the traditional manner. Presents a new approach where students prepare presentations, questions, and discussion topics. During laboratory periods, students conducted their own long-term research projects. (PR)

Experiments in optics for younger students by and for older students

NASA Astrophysics Data System (ADS)

Masi, James V.

1995-10-01

Under the auspices of a joint NSF/DOE grant for science and mathematics, the Electrical Engineering Department of the Engineering School at Western New England College developed a program of instruction in optics and optical applications for local Junior High School students. College level juniors and professors in the electrical engineering department, after the juniors had taken a one semester introductory course in optics and electro-optics, served as instructors in teaching and laboratory instruction in such diverse areas as solar cells/light detection, light sources, simple optics, optical fibers, liquid crystals, and lasers. Concepts such as seismic monitoring, Fourier transforms, power generation, information transfer, and many other applications were explained at level by the college students to the junior high school students with great effectiveness. Students at the lower level caught the enthusiasm of those at the upper level and learned with retention. Seven years into the program, the pros and cons are presented, the now- college bound students and their observations are detailed, and the learning experience for all is assessed, with scenarios for alternate programs suggested.

First-year Engineering Education with the Creative Electrical Engineering Laboratory

NASA Astrophysics Data System (ADS)

Tsukamoto, Takehiko; Sugito, Tetsumasa; Ozeki, Osamu; Ushiroda, Sumio

The Department of Electrical and Electronic Engineering in Toyota National College of Technology has put great emphasis on fundamental subjects. We introduced the creative electrical engineering laboratory into the first-year engineering education since 1998. The laboratory concentrates on the practice exercise. The final questionnaire of students showed that our first-year education is very effective to promote students motivation and their scholastic ability in engineering.

A Research Module for the Organic Chemistry Laboratory: Multistep Synthesis of a Fluorous Dye Molecule

PubMed Central

2014-01-01

A multi-session research-like module has been developed for use in the undergraduate organic teaching laboratory curriculum. Students are tasked with planning and executing the synthesis of a novel fluorous dye molecule and using it to explore a fluorous affinity chromatography separation technique, which is the first implementation of this technique in a teaching laboratory. Key elements of the project include gradually introducing students to the use of the chemical literature to facilitate their searching, as well as deliberate constraints designed to force them to think critically about reaction design and optimization in organic chemistry. The project also introduces students to some advanced laboratory practices such as Schlenk techniques, degassing of reaction mixtures, affinity chromatography, and microwave-assisted chemistry. This provides students a teaching laboratory experience that closely mirrors authentic synthetic organic chemistry practice in laboratories throughout the world. PMID:24501431

A Research Module for the Organic Chemistry Laboratory: Multistep Synthesis of a Fluorous Dye Molecule.

PubMed

Slade, Michael C; Raker, Jeffrey R; Kobilka, Brandon; Pohl, Nicola L B

2014-01-14

A multi-session research-like module has been developed for use in the undergraduate organic teaching laboratory curriculum. Students are tasked with planning and executing the synthesis of a novel fluorous dye molecule and using it to explore a fluorous affinity chromatography separation technique, which is the first implementation of this technique in a teaching laboratory. Key elements of the project include gradually introducing students to the use of the chemical literature to facilitate their searching, as well as deliberate constraints designed to force them to think critically about reaction design and optimization in organic chemistry. The project also introduces students to some advanced laboratory practices such as Schlenk techniques, degassing of reaction mixtures, affinity chromatography, and microwave-assisted chemistry. This provides students a teaching laboratory experience that closely mirrors authentic synthetic organic chemistry practice in laboratories throughout the world.

An educational laboratory virtual instrumentation suite assisted experiment for studying fundamentals of series resistance-inductance-capacitance circuit

NASA Astrophysics Data System (ADS)

Rana, K. P. S.; Kumar, Vineet; Mendiratta, Jatin

2017-11-01

One of the most elementary concepts in freshmen Electrical Engineering subject comprises the Resistance-Inductance-Capacitance (RLC) circuit fundamentals, that is, their time and frequency domain responses. For a beginner, generally, it is difficult to understand and appreciate the step and the frequency responses, particularly the resonance. This paper proposes a student-friendly teaching and learning approach by inculcating the multifaceted versatile software LabVIEWTM along with the educational laboratory virtual instrumentation suite hardware, for studying the RLC circuit time and frequency domain responses. The proposed approach has offered an interactive laboratory experiment where students can model circuits in simulation and hardware circuits on prototype board, and then compare their performances. The theoretical simulations and the obtained experimental data are found to be in very close agreement, thereby enhancing the conviction of students. Finally, the proposed methodology was also subjected to the assessment of learning outcomes based on student feedback, and an average score of 8.05 out of 10 with a standard deviation of 0.471 was received, indicating the overall satisfaction of the students.

Software Engineering Laboratory Series: Proceedings of the Twenty-First Annual Software Engineering Workshop

NASA Technical Reports Server (NTRS)

1996-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Software Engineering Laboratory Series: Proceedings of the Twenty-Second Annual Software Engineering Workshop

NASA Technical Reports Server (NTRS)

1997-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

VERIFI | Virtual Engine Research Institute and Fuels Initiative

Science.gov Websites

VERIFI Virtual Engine Research Institute and Fuels Initiative Argonne National Laboratory Skip to Virtual Engine Research Institute and Fuels Initiative (VERIFI) at Argonne National Laboratory is the Argonne National Laboratory in which to answer your complex engine questions, verify the uncertainties

Software engineering laboratory series: Annotated bibliography of software engineering laboratory literature

NASA Technical Reports Server (NTRS)

Morusiewicz, Linda; Valett, Jon

1992-01-01

This document is an annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory. More than 100 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. This document has been updated and reorganized substantially since the original version (SEL-82-006, November 1982). All materials have been grouped into eight general subject areas for easy reference: (1) the Software Engineering Laboratory; (2) the Software Engineering Laboratory: Software Development Documents; (3) Software Tools; (4) Software Models; (5) Software Measurement; (6) Technology Evaluations; (7) Ada Technology; and (8) Data Collection. This document contains an index of these publications classified by individual author.

Enhancing STEM Education through Cubesats: Using Satellite Integration as a Teaching Tool at a Non-Tech School

NASA Astrophysics Data System (ADS)

Bernardes, S.; Cotten, D. L.

2016-12-01

University-based satellite programs have been successfully used as a platform for teaching STEM related fields, bringing tremendous benefits to graduate and undergraduate education. Considering their infrastructure and curricula, tech schools have traditionally been considered logical candidates for hosting such programs. More recently, with the dissemination of small satellites initiatives, non-tech schools have been presented the opportunity of developing satellite design and implementation programs. This work reports on the experiences and challenges associated with implementing a satellite program at the University of Georgia (UGA), a non-tech university. With funding from the Air Force Research Laboratory's (AFRL) University Nanosat Program (UNP) and NASA's Undergraduate Student Instrument Project (USIP) a team of undergraduates at UGA has recently been tasked with building two small satellites and helping to create a Small Satellite Research Laboratory (SSRL) at the university. Unique features of the satellite program at UGA include its team of students from a broad range of backgrounds and departments (Engineering, Computer Science, Art, Business, and Geography) and the previous exposure of many of these students to synergistic technologies, including arduino and unmanned aerial systems. We show how informal exposure to those technologies and willingness of students to focus on areas outside of their field of study can benefit from the implementation of satellite programs. In this regard, we report on methods and techniques used to find and recruit driven and knowledgeable students to work in a high paced field such as satellite system integration. We show how students and faculty from multiple departments have collaborated to reach a common, far reaching goal and describe our proposed methods to evaluate and measure educational goals based around SSRL and its projects. We also present the challenges associated with the lack of a developed engineering program, including our solutions to a shortage of equipment and expertise regarding building satellite systems and a satellite laboratory. Finally, we our outreach methods, including K-12, and share our experience and successes finding industry partners, considering an absence of background in the field and prior collaborations.

Water Mediated Wittig Reactions of Aldehydes in the Teaching Laboratory: Using Sodium Bicarbonate for the in Situ Formation of Stabilized Ylides

ERIC Educational Resources Information Center

Kelly, Michael J. B.; Fallot, Lucas B.; Gustafson, Jeffrey L.; Bergdahl, B. Mikael

2016-01-01

The synthesis of alkenes using the Wittig reaction is a traditional part of many undergraduate organic chemistry teaching laboratory curricula. The aqueous medium version of the Wittig reaction presented is a reliable adaptation of this alkene formation reaction as a very safe alternative in the introductory organic chemistry laboratory. The…

A Survey of Beginning Crop Science Courses at 49 U.S. Universities. II. Laboratory Format, Teaching Methods, and Topical Content.

ERIC Educational Resources Information Center

Connors, Krista L.; Karnok, Keith J.

1986-01-01

This paper is the second of a two-part series which discusses the findings related to laboratory segments in the beginning crop science courses offered in Land Grant institutions. Survey results reveal that laboratories are used but employ traditional teaching rather than individualized or auto-tutorial techniques. (ML)

Draftsmen at Work during Construction of the Aircraft Engine Research Laboratory

NASA Image and Video Library

1942-09-21

The National Advisory Committee for Aeronautics (NACA) Aircraft Engine Research Laboratory was designed by a group of engineers at the Langley Memorial Aeronautical Laboratory in late 1940 and 1941. Under the guidance of Ernest Whitney, the men worked on drawings and calculations in a room above Langley’s Structural Research Laboratory. The main Aircraft Engine Research Laboratory design group originally consisted of approximately 30 engineers and draftsmen, but there were smaller groups working separately on specific facilities. The new engine lab would have six principal buildings: the Engine Research Building, hangar, Fuels and Lubricants Building, Administration Building, Propeller Test Stand, and Altitude Wind Tunnel. In December 1941 most of those working on the project transferred to Cleveland from Langley. Harrison Underwood and Charles Egan led 18 architectural, 26 machine equipment, 3 structural and 10 mechanical draftsmen. Initially these staff members were housed in temporary offices in the hangar. As sections of the four-acre Engine Research Building were completed in the summer of 1942, the design team began relocating there. The Engine Research Building contained a variety of test cells and laboratories to address virtually every aspect of piston engine research. It also contained a two-story office wing, seen in this photograph that would later house many of the powerplant research engineers.

Role-play and the Industrial Revolution: an STS approach to the teaching of steam engines

NASA Astrophysics Data System (ADS)

Sabka, Diego; Pereira de Pereira, Alexsandro; Lima Junior, Paulo

2016-11-01

Role-play is an interesting, although underexplored, way of teaching physics in high school. This paper presents a science-technology-society (STS) approach to the teaching of heat engines based on a role-play of the Industrial Revolution. Enacting the role-play, students are presented not only to scientific concepts, but also to the social and technological controversies of industrial development.

Sustainability in Chemical Engineering Curriculum

ERIC Educational Resources Information Center

Glassey, Jarka; Haile, Sue

2012-01-01

Purpose: The purpose of this paper is to describe a concentrated strategy to embed sustainability teaching into a (chemical) engineering undergraduate curriculum throughout the whole programme. Innovative teaching approaches in subject-specific context are described and their efficiency investigated. Design/methodology/approach: The activities in…

Design of Smart Educational Robot as a Tool For Teaching Media Based on Contextual Teaching and Learning to Improve the Skill of Electrical Engineering Student

NASA Astrophysics Data System (ADS)

Zuhrie, M. S.; Basuki, I.; Asto, B. I. G. P.; Anifah, L.

2018-04-01

The development of robotics in Indonesia has been very encouraging. The barometer is the success of the Indonesian Robot Contest. The focus of research is a teaching module manufacturing, planning mechanical design, control system through microprocessor technology and maneuverability of the robot. Contextual Teaching and Learning (CTL) strategy is the concept of learning where the teacher brings the real world into the classroom and encourage students to make connections between knowledge possessed by its application in everyday life. This research the development model used is the 4-D model. This Model consists of four stages: Define Stage, Design Stage, Develop Stage, and Disseminate Stage. This research was conducted by applying the research design development with the aim to produce a tool of learning in the form of smart educational robot modules and kit based on Contextual Teaching and Learning at the Department of Electrical Engineering to improve the skills of the Electrical Engineering student. Socialization questionnaires showed that levels of the student majoring in electrical engineering competencies image currently only limited to conventional machines. The average assessment is 3.34 validator included in either category. Modules developed can give hope to the future are able to produce Intelligent Robot Tool for Teaching.

COED Transactions, Vol. X, No. 4, April 1978. An Experience in Teaching "COBOL?" to Graduate Engineers.

ERIC Educational Resources Information Center

Bremmer, Dale; Childs, Bart

This document discusses the importance of computing knowledge and experience in the techniques of fast data retrieval for today's engineer. It describes a course designed to teach the engineer the COBOL Language structure. One of the projects of the course, a report generator (REGE) written in COBOL which is used to alter, sort and print selected…

A Joint Venture Model for Teaching Required Courses in "Ethics and Engineering" to Engineering Students

ERIC Educational Resources Information Center

Zandvoort, H.; Van Hasselt, G. J.; Bonnet, J. A. B. A. F.

2008-01-01

We present our experience, spanning more than 10 years of teaching a course on "ethics and engineering" for a group of MSc programmes in applied sciences at Delft University of Technology. The course is taught by a team of teachers from the faculty of Applied Sciences and from the department of Philosophy of the Faculty of Technology,…

Promoting Reflection on Science, Technology, and Society among Engineering Students through an EAP Online Learning Environment

ERIC Educational Resources Information Center

Arno-Macia, Elisabet; Rueda-Ramos, Carmen

2011-01-01

With the new European framework, as EAP lecturers in an engineering college, we are reappraising our teaching and the position of our courses. From the perspective of engineering education in the 21st century, we believe that EAP teaching can focus not only on language and communication needs, but also on developing critical thinking about science…

Teaching Design in the First Years of a Traditional Mechanical Engineering Degree: Methods, Issues and Future Perspectives

ERIC Educational Resources Information Center

Silva, Arlindo; Fontul, Mihail; Henriques, Elsa

2015-01-01

Engineering design is known as an answer to an ill-defined problem. As any answer to an ill-defined problem, it can never be completely right or absolutely wrong. The methods that universities use to teach engineering design, as a consequence of this, suffer from the same fate. However, the accumulated experience with the "chalk and…

Teaching Engineering Practices

NASA Astrophysics Data System (ADS)

Cunningham, Christine M.; Carlsen, William S.

2014-03-01

Engineering is featured prominently in the Next Generation Science Standards (NGSS) and related reform documents, but how its nature and methods are described is problematic. This paper is a systematic review and critique of that representation, and proposes that the disciplinary core ideas of engineering (as described in the NGSS) can be disregarded safely if the practices of engineering are better articulated and modeled through student engagement in engineering projects. A clearer distinction between science and engineering practices is outlined, and prior research is described that suggests that precollege engineering design can strengthen children's understandings about scientific concepts. However, a piecemeal approach to teaching engineering practices is unlikely to result in students understanding engineering as a discipline. The implications for science teacher education are supplemented with lessons learned from a number of engineering education professional development projects.

Manual for Teaching Assistants.

ERIC Educational Resources Information Center

Wisconsin Univ., Madison. Coll. of Letters and Science.

Information on teaching techniques, student evaluation, and campus resources is presented for new teaching assistants. Topics include: lecturing, leading discussion sessions (especially in the humanities and social sciences), teaching the laboratory section, teaching a section of a course, teaching a foreign language, office hours, and use of the…

Modeling Sources of Teaching Self-Efficacy for Science, Technology, Engineering, and Mathematics Graduate Teaching Assistants

PubMed Central

DeChenne, Sue Ellen; Koziol, Natalie; Needham, Mark; Enochs, Larry

2015-01-01

Graduate teaching assistants (GTAs) in science, technology, engineering, and mathematics (STEM) have a large impact on undergraduate instruction but are often poorly prepared to teach. Teaching self-efficacy, an instructor’s belief in his or her ability to teach specific student populations a specific subject, is an important predictor of teaching skill and student achievement. A model of sources of teaching self-efficacy is developed from the GTA literature. This model indicates that teaching experience, departmental teaching climate (including peer and supervisor relationships), and GTA professional development (PD) can act as sources of teaching self-efficacy. The model is pilot tested with 128 GTAs from nine different STEM departments at a midsized research university. Structural equation modeling reveals that K–12 teaching experience, hours and perceived quality of GTA PD, and perception of the departmental facilitating environment are significant factors that explain 32% of the variance in the teaching self-efficacy of STEM GTAs. This model highlights the important contributions of the departmental environment and GTA PD in the development of teaching self-efficacy for STEM GTAs. PMID:26250562

Learning to teach effectively: Science, technology, engineering, and mathematics graduate teaching assistants' teaching self-efficacy

NASA Astrophysics Data System (ADS)

Dechenne, Sue Ellen

Graduate teaching assistants (GTAs) from science, technology, engineering, and mathematics (STEM) are important in the teaching of undergraduate students (Golde & Dore, 2001). However, they are often poorly prepared for teaching (Luft, Kurdziel, Roehrig, & Turner, 2004). This dissertation addresses teaching effectiveness in three related manuscripts: (1) A position paper that summarizes the current research on and develops a model of GTA teaching effectiveness. (2) An adaptation and validation of two instruments; GTA perception of teaching training and STEM GTA teaching self-efficacy. (3) A model test of factors that predict STEM GTA teaching self-efficacy. Together these three papers address key questions in the understanding of teaching effectiveness in STEM GTAs including: (a) What is our current knowledge of factors that affect the teaching effectiveness of GTAs? (b) Given that teaching self-efficacy is strongly linked to teaching performance, how can we measure STEM GTAs teaching self-efficacy? (c) Is there a better way to measure GTA teaching training than currently exists? (d) What factors predict STEM GTA teaching self-efficacy? An original model for GTA teaching effectiveness was developed from a thorough search of the GTA teaching literature. The two instruments---perception of training and teaching self-efficacy---were tested through self-report surveys using STEM GTAs from six different universities including Oregon State University (OSU). The data was analyzed using exploratory and confirmatory factor analysis. Using GTAs from the OSU colleges of science and engineering, the model of sources of STEM GTA teaching self-efficacy was tested by administering self-report surveys and analyzed by using OLS regression analysis. Language and cultural proficiency, departmental teaching climate, teaching self-efficacy, GTA training, and teaching experience affect GTA teaching effectiveness. GTA teaching self-efficacy is a second-order factor combined from self-efficacy for instructional strategies and a positive learning environment. It is correlated to GTA perception of teaching training and university GTA training. The K-12 teaching experience, GTA perception of teaching training, and facilitating factors in the departmental climate predict STEM GTA teaching self-efficacy. Hours of GTA training and supervision are fully mediated by perception of GTA training. Implications for research and training of STEM GTAs are discussed.

Promoting Access, Retention, and Interest in Astronomy Higher Education: Developing the STEM Professionals of Tomorrow in New Mexico

NASA Astrophysics Data System (ADS)

Vogt, N. P.; Muise, A. S.; Cook, S.; Voges, E.

2011-09-01

Economic stability and success are becoming increasingly tied to the successful acquisition of basic academic skills, with the emergence of a computer- and data-oriented society. The recent doubling of the statewide requirement for laboratory science courses at the college level in New Mexico thus represents both an opportunity to further aid in the development of math and science skills in our general population and an added barrier to degree completion. Couple this to a geographically dispersed population of non-traditional students, with workforce and family responsibilities that compete directly for time with academics, and we have a compelling need for alternate methods of teaching science in New Mexico. We present a set of NASA- and NSF-sponsored resources under development to aid in teaching astronomy as a laboratory science at the college level, with usage results for a pilot group of students. Primary components include a self-review database of 10,000+ questions, an instructor review interface, a set of laboratory exercises suitable for students working alone at a distance, and interviews with diverse science, technology, engineering, and mathematics (STEM) individuals to help combat stereotype threat. We discuss learning strategies often employed by students without substantial scientific training and ways to incorporate these strategies into a conceptual framework based on the scientific method and basic techniques for data analysis. Interested science educators may request guest user status to access our self-review database and explore the possibility of using the database for a class or cohort of students at their own institutions.

Annotated bibliography of Software Engineering Laboratory literature

NASA Technical Reports Server (NTRS)

Morusiewicz, Linda; Valett, Jon D.

1991-01-01

An annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory is given. More than 100 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. All materials have been grouped into eight general subject areas for easy reference: The Software Engineering Laboratory; The Software Engineering Laboratory: Software Development Documents; Software Tools; Software Models; Software Measurement; Technology Evaluations; Ada Technology; and Data Collection. Subject and author indexes further classify these documents by specific topic and individual author.

Continuous Flow Science in an Undergraduate Teaching Laboratory: Photocatalytic Thiol-Ene Reaction Using Visible Light

ERIC Educational Resources Information Center

Santandrea, Jeffrey; Kairouz, Vanessa; Collins, Shawn K.

2018-01-01

An undergraduate teaching laboratory experiment involving a continuous flow, photocatalytic thiol-ene reaction using visible-light irradiation is described that allows students to explore concepts of green chemistry, photochemistry, photocatalysis, and continuous flow chemistry.

Computerized Cognition Laboratory.

ERIC Educational Resources Information Center

Motes, Michael A.; Wiegmann, Douglas A.

1999-01-01

Describes a software package entitled the "Computerized Cognition Laboratory" that helps integrate the teaching of cognitive psychology and research methods. Allows students to explore short-term memory, long-term memory, and decision making. Can also be used to teach the application of several statistical procedures. (DSK)

Remote access laboratories in Australia and Europe

NASA Astrophysics Data System (ADS)

Ku, H.; Ahfock, T.; Yusaf, T.

2011-06-01

Remote access laboratories (RALs) were first developed in 1994 in Australia and Switzerland. The main purposes of developing them are to enable students to do their experiments at their own pace, time and locations and to enable students and teaching staff to get access to facilities beyond their institutions. Currently, most of the experiments carried out through RALs in Australia are heavily biased towards electrical, electronic and computer engineering disciplines. However, the experiments carried out through RALs in Europe had more variety, in addition to the traditional electrical, electronic and computer engineering disciplines, there were experiments in mechanical and mechatronic disciplines. It was found that RALs are now being developed aggressively in Australia and Europe and it can be argued that RALs will develop further and faster in the future with improving Internet technology. The rising costs of real experimental equipment will also speed up their development because by making the equipment remotely accessible, the cost can be shared by more universities or institutions and this will improve their cost-effectiveness. Their development would be particularly rapid in large countries with small populations such as Australia, Canada and Russia, because of the scale of economy. Reusability of software, interoperability in software implementation, computer supported collaborative learning and convergence with learning management systems are the required development of future RALs.

Broadening ethics teaching in engineering: beyond the individualistic approach.

PubMed

Conlon, Eddie; Zandvoort, Henk

2011-06-01

There is a widespread approach to the teaching of ethics to engineering students in which the exclusive focus is on engineers as individual agents and the broader context in which they do their work is ignored. Although this approach has frequently been criticised in the literature, it persists on a wide scale, as can be inferred from accounts in the educational literature and from the contents of widely used textbooks in engineering ethics. In this contribution we intend to: (1) Restate why the individualistic approach to the teaching of ethics to engineering students is inadequate in view of preparing them for ethical, professional and social responsibility; (2) Examine the existing literature regarding the possible contribution of Science, Technology and Society (STS) scholarship in addressing the inadequacies of the individualistic approach; and (3) Assess this possible contribution of STS in order to realise desired learning outcomes regarding the preparation of students for ethical and social responsibility.

Impromptu Teaching Model for Pre-Service Teacher Preparation.

ERIC Educational Resources Information Center

Peterson, Paul E.; Peterson, Susan L.

The Impromptu Teaching Model was designed by the University of Central Arkansas for use by preservice teachers in laboratory teaching experiences. Two teaching exercises, microteaching and reflective teaching, form the basis for impromptu teaching. Microteaching provides teachers with the opportunity to master various technical skills of the…

Engineering the future with America's high school students

NASA Technical Reports Server (NTRS)

Farrance, M. A.; Jenner, J. W.

1993-01-01

The number of students enrolled in engineering is declining while the need for engineers is increasing. One contributing factor is that most high school students have little or no knowledge about what engineering is, or what engineers do. To teach young students about engineering, engineers need good tools. This paper presents a course of study developed and used by the authors in a junior college course for high school students. Students learned about engineering through independent student projects, in-class problem solving, and use of career information resources. Selected activities from the course can be adapted to teach students about engineering in other settings. Among the most successful techniques were the student research paper assignments, working out a solution to an engineering problem as a class exercise, and the use of technical materials to illustrate engineering concepts and demonstrate 'tools of the trade'.

A CAL Program to Teach the Basic Principles of Genetic Engineering--A Change from the Traditional Approach.

ERIC Educational Resources Information Center

Dewhurst, D. G.; And Others

1989-01-01

An interactive computer-assisted learning program written for the BBC microcomputer to teach the basic principles of genetic engineering is described. Discussed are the hardware requirements software, use of the program, and assessment. (Author/CW)

Quality knowledge of science through virtual laboratory as an element of visualization

NASA Astrophysics Data System (ADS)

Rizman Herga, Natasa

Doctoral dissertation discusses the use of virtual laboratory for learning and teaching chemical concepts at science classes in the seventh grade of primary school. The dissertation has got a two-part structure. In the first theoretical part presents a general platform of teaching science in elementary school, teaching forms and methods of teaching and among modern approaches we highlight experimental work. Particular emphasis was placed on the use of new technologies in education and virtual laboratories. Scientific findings on the importance of visualization of science concepts and their triple nature of their understanding are presented. These findings represent a fundamental foundation of empirical research presented in the second part of the doctoral dissertation, whose basic purpose was to examine the effectiveness of using virtual laboratory for teaching and learning chemical contents at science from students' point of view on knowledge and interest. We designed a didactic experiment in which 225 pupils participated. The work was conducted in the experimental and control group. Prior to its execution, the existing school practice among science and chemistry teachers was analysed in terms of: (1) inclusion of experimental work as a fundamental method of active learning chemical contents, (2) the use of visualization methods in the classroom and (3) the use of a virtual laboratory. The main findings of the empirical research, carried out in the school year 2012/2013, in which 48 science and chemistry participated, are that teachers often include experimental work when teaching chemical contents. Interviewed science teachers use a variety of visualization methods when presenting science concepts, in particular computer animation and simulation. Using virtual laboratory as a new strategy for teaching and learning chemical contents is not common because teachers lack special-didactic skills, enabling them to use virtual reality technology. Based on the didactic experiment, carried out over a period of two school years (2012/2013 and 2013/2014) in ten primary schools, the effectiveness of teaching carried out with the support of a virtual laboratory was analyzed. The obtained empirical findings reveal that the use of virtual laboratory has great impact on the pupils' knowledge and interest. At the end of the experiment, pupils in the experimental group had an advantage according to knowledge of chemical contents in science. Also, the use of virtual laboratory had an impact on the sustainability of the acquired knowledge of science contents and pupils' interest at the end of the experiment, because the pupils in the experimental group had a higher interest for learning science contents. The didactic experiment determined, that the use of virtual laboratory enables quality learning and teaching chemical contents of science, because it allows: (1) experimental work as an active learning method, (2) the visualization of abstract concepts and phenomena, (3) dynamic sub micro presentations (4) integration of all three levels of the chemical concept as a whole and (5) positively impacts pupils' interest, knowledge and sustainability of the acquired knowledge.

The GIST Model for Selection and Modification of Scientific Research for the College Teaching Laboratory Based on Root Competition Investigations

ERIC Educational Resources Information Center

Elliott, Shannon Snyder

2007-01-01

The purpose of this study is to first develop an 8-week college teaching module based on root competition literature. The split-root technique is adapted for the teaching laboratory, and the Sugar Ann English pea (Pisum sativum var. Sugar Ann English) is selected as the species of interest prior to designing experiments, either original or…

The Effect of Laboratory Training Model of Teaching and Traditional Method on Knowledge, Comprehension, Application, Skills-Components of Achievement, Total Achievement and Retention Level in Chemistry

ERIC Educational Resources Information Center

Badeleh, Alireza

2011-01-01

The present study aimed at finding the effectiveness of the Laboratory Training Model of Teaching (LTM) and comparing it with the traditional methods of teaching chemistry to seventh standard students. It strived to determine whether the (LTM) method in chemistry would be significantly more effective than the Traditional method in respect to the…

Technology Transfer of the Air Quality Assessment Model.

DTIC Science & Technology

1984-02-01

i T I, _______ ENGINEERING & SERVICES LABORATORY AIR FORCE ENGINEERING & SERVICES CENTER TYNOALL AIR FORCE BASE. FLORIDA 32403 OTIC FILE CO84 03...30 015 NOTICE PLEASE DO NOT REQUEST COPIES OF THIS REPORT FRO(M HQ AFESC./RD ( ENGINEERING AND SERVICES LABORATORY). ADDITONAL COPIES MAY BE PURCHASED...report was prepared by the Air Force Engineering and Services Center, Engineering and Services Laboratory, (AFESC/ RDV) Tyndall AFB, FL. This report

Uncovering Barriers to Teaching Assistants (TAs) Implementing Inquiry Teaching: Inconsistent Facilitation Techniques, Student Resistance, and Reluctance to Share Control over Learning with Students.

PubMed

Gormally, Cara; Sullivan, Carol Subiño; Szeinbaum, Nadia

2016-05-01

Inquiry-based teaching approaches are increasingly being adopted in biology laboratories. Yet teaching assistants (TAs), often novice teachers, teach the majority of laboratory courses in US research universities. This study analyzed the perspectives of TAs and their students and used classroom observations to uncover challenges faced by TAs during their first year of inquiry-based teaching. Our study revealed three insights about barriers to effective inquiry teaching practices: 1) TAs lack sufficient facilitation skills; 2) TAs struggle to share control over learning with students as they reconcile long-standing teaching beliefs with newly learned approaches, consequently undermining their fledgling ability to use inquiry approaches; and 3) student evaluations reinforce teacher-centered behaviors as TAs receive positive feedback conflicting with inquiry approaches. We make recommendations, including changing instructional feedback to focus on learner-centered teaching practices. We urge TA mentors to engage TAs in discussions to uncover teaching beliefs underlying teaching choices and support TAs through targeted feedback and practice.

A Modular Laser Apparatus for Polarimetry, Nephelometry, and Fluorimetry in General Chemistry

ERIC Educational Resources Information Center

Jurzenski, Jessica; Darveau, Scott A.; Gindt, Yvonne; Mueller, Jessica; Vaverka, April; Barta, Cheri; Fitch, Anthony

2004-01-01

A novel apparatus that strengthens the connection between research and teaching laboratories and serves multiple purposes is described. A versatile laser apparatus suitable for the undergraduate teaching laboratory that may serve as polarimeter, nephelometer or fluorimeter is designed.

Waste Disposal in the Laboratory: Teaching Responsibility and Safety.

ERIC Educational Resources Information Center

Allen, Ralph O.

1983-01-01

Discusses the generation, collection, and disposal of hazardous and other wastes in the chemistry laboratory. Offers suggestions related to these three areas to provide a safe teaching environment, including minimizing amounts of reagents used (and potentially wasted) by scaling down experiments. (JN)

Two Readily-Constructed Instruments for the Teaching Laboratory.

ERIC Educational Resources Information Center

Isaacs, Neil S.

1983-01-01

Reported are designs for a colorimeter (absorptiometer) and polarimeter, both of which may be constructed readily with average workshop facilities and whose performance is superior to many commercial instruments commonly used in teaching laboratories. Includes pertinent diagrams, operating instructions, and sample output. (JN)

Learning in a Gene Technology Laboratory with Educational Focus: Results of a Teaching Unit with Authentic Experiments

ERIC Educational Resources Information Center

Scharfenberg, Franz-Josef; Bogner, Franz X.; Klautke, Siegfried

2007-01-01

In an effort to overcome deficiencies in teaching molecular biology at school, a workshop in an out-of-school laboratory including only authentic experiments was developed. Evaluation of 337 A-level 12th graders followed a quasi-experimental design, with one hands-on group, two non-experimental control groups (at school/in the laboratory), and one…

A Design of Innovative Engineering Drawing Teaching Materials

NASA Astrophysics Data System (ADS)

Mujiarto; Djohar, A.; Komaro, M.

2018-02-01

Good teaching is influenced by several things such as effective school leaders and skilled teachers who are able to use information communication technology as a medium of learning. The purpose of this research in general is to develop innovative teaching materials in the form of multimedia animation for engineering drawing in the field of technology and engineering at vocational high school. Research method used research and development (research and development / R & D). The results showed that the E-book Multimedia Animation Engineering Drawing (E-MMAED) is easy to possess and contains complete material. Students stated that the use of E-MMAED adds to learning motivation and improves learning outcomes (student competencies). We recommend that teachers apply E-MMAED as a learning medium and create other innovations to improve student competences.

Paired peer learning through engineering education outreach

NASA Astrophysics Data System (ADS)

Fogg-Rogers, Laura; Lewis, Fay; Edmonds, Juliet

2017-01-01

Undergraduate education incorporating active learning and vicarious experience through education outreach presents a critical opportunity to influence future engineering teaching and practice capabilities. Engineering education outreach activities have been shown to have multiple benefits; increasing interest and engagement with science and engineering for school children, providing teachers with expert contributions to engineering subject knowledge, and developing professional generic skills for engineers such as communication and teamwork. This pilot intervention paired 10 pre-service teachers and 11 student engineers to enact engineering outreach in primary schools, reaching 269 children. A longitudinal mixed methods design was employed to measure change in attitudes and Education Outreach Self-Efficacy in student engineers; alongside attitudes, Teaching Engineering Self-Efficacy and Engineering Subject Knowledge Confidence in pre-service teachers. Highly significant improvements were noted in the pre-service teachers' confidence and self-efficacy, while both the teachers and engineers qualitatively described benefits arising from the paired peer mentor model.

Stirling laboratory research engine survey report

NASA Technical Reports Server (NTRS)

Anderson, J. W.; Hoehn, F. W.

1979-01-01

As one step in expanding the knowledge relative to and accelerating the development of Stirling engines, NASA, through the Jet Propulsion Laboratory (JPL), is sponsoring a program which will lead to a versatile Stirling Laboratory Research Engine (SLRE). An objective of this program is to lay the groundwork for a commercial version of this engine. It is important to consider, at an early stage in the engine's development, the needs of the potential users so that the SLRE can support the requirements of educators and researchers in academic, industrial, and government laboratories. For this reason, a survey was performed, the results of which are described.

Teaching Vectors Through an Interactive Game Based Laboratory

NASA Astrophysics Data System (ADS)

O'Brien, James; Sirokman, Gergely

2014-03-01

In recent years, science and particularly physics education has been furthered by the use of project based interactive learning [1]. There is a tremendous amount of evidence [2] that use of these techniques in a college learning environment leads to a deeper appreciation and understanding of fundamental concepts. Since vectors are the basis for any advancement in physics and engineering courses the cornerstone of any physics regimen is a concrete and comprehensive introduction to vectors. Here, we introduce a new turn based vector game that we have developed to help supplement traditional vector learning practices, which allows students to be creative, work together as a team, and accomplish a goal through the understanding of basic vector concepts.

Editors' overview perspectives on teaching social responsibility to students in science and engineering.

PubMed

Zandvoort, Henk; Børsen, Tom; Deneke, Michael; Bird, Stephanie J

2013-12-01

Global society is facing formidable current and future problems that threaten the prospects for justice and peace, sustainability, and the well-being of humanity both now and in the future. Many of these problems are related to science and technology and to how they function in the world. If the social responsibility of scientists and engineers implies a duty to safeguard or promote a peaceful, just and sustainable world society, then science and engineering education should empower students to fulfil this responsibility. The contributions to this special issue present European examples of teaching social responsibility to students in science and engineering, and provide examples and discussion of how this teaching can be promoted, and of obstacles that are encountered. Speaking generally, education aimed at preparing future scientists and engineers for social responsibility is presently very limited and seemingly insufficient in view of the enormous ethical and social problems that are associated with current science and technology. Although many social, political and professional organisations have expressed the need for the provision of teaching for social responsibility, important and persistent barriers stand in the way of its sustained development. What is needed are both bottom-up teaching initiatives from individuals or groups of academic teachers, and top-down support to secure appropriate embedding in the university. Often the latter is lacking or inadequate. Educational policies at the national or international level, such as the Bologna agreements in Europe, can be an opportunity for introducing teaching for social responsibility. However, frequently no or only limited positive effect of such policies can be discerned. Existing accreditation and evaluation mechanisms do not guarantee appropriate attention to teaching for social responsibility, because, in their current form, they provide no guarantee that the curricula pay sufficient attention to teaching goals that are desirable for society as a whole.

Teaching Chromatography Using Virtual Laboratory Exercises

ERIC Educational Resources Information Center

Stone, David C.

2007-01-01

Though deceptively simple to teach, chromatography presents many nuances and complex interactions that challenge both student and instructor. Time and instrumentation provide major obstacles to a thorough examination of these details in the laboratory. Modern chromatographic method-development software provides an opportunity to overcome this,…

Integrating Research, Teaching and Learning: Preparing the Future National STEM Faculty

NASA Astrophysics Data System (ADS)

Hooper, E. J.; Pfund, C.; Mathieu, R.

2010-08-01

A network of universities (Howard, Michigan State, Texas A&M, University of Colorado at Boulder, University of Wisconsin-Madison, Vanderbilt) have created a National Science Foundation-funded network to prepare a future national STEM (science, technology, engineering, mathematics) faculty committed to learning, implementing, and advancing teaching techniques that are effective for the wide range of students enrolled in higher education. The Center for the Integration of Research, Teaching and Learning (CIRTL; http://www.cirtl.net) develops, implements and evaluates professional development programs for future and current faculty. The programs comprise graduate courses, internships, and workshops, all integrated within campus learning communities. These elements are unified and guided by adherence to three core principles, or pillars: "Teaching as Research," whereby research skills are applied to evaluating and advancing undergraduate learning; "Learning through Diversity," in which the diversity of students' backgrounds and experiences are used as a rich resource to enhance teaching and learning; and "Learning Communities" that foster shared learning and discovery among students, and between future and current faculty within a department or institution. CIRTL established a laboratory for testing its ideas and practices at the University of Wisconsin-Madison, known as the Delta Program in Research, Teaching and Learning (http://www.delta.wisc.edu). The program offers project-based graduate courses, research mentor training, and workshops for post-docs, staff, and faculty. In addition, graduate students and post-docs can partner with a faculty member in a teaching-as-research internship to define and tackle a specific teaching and learning problem. Finally, students can obtain a Delta Certificate as testimony to their engagement in and commitment to teaching and learning. Delta has proved very successful, having served over 1500 UW-Madison instructors from graduate students to full professors. UW-Madison values the program to the point of now funding it internally.

Evaluation of the Redesign of an Undergraduate Cell Biology Course

PubMed Central

McEwen, Laura April; Harris, dik; Schmid, Richard F.; Vogel, Jackie; Western, Tamara

2009-01-01

This article offers a case study of the evaluation of a redesigned and redeveloped laboratory-based cell biology course. The course was a compulsory element of the biology program, but the laboratory had become outdated and was inadequately equipped. With the support of a faculty-based teaching improvement project, the teaching team redesigned the course and re-equipped the laboratory, using a more learner-centered, constructivist approach. The focus of the article is on the project-supported evaluation of the redesign rather than the redesign per se. The evaluation involved aspects well beyond standard course assessments, including the gathering of self-reported data from the students concerning both the laboratory component and the technical skills associated with the course. The comparison of pre- and postdata gave valuable information to the teaching team on course design issues and skill acquisition. It is argued that the evaluation process was an effective use of the scarce resources of the teaching improvement project. PMID:19255138

Low-Cost Virtual Laboratory Workbench for Electronic Engineering

ERIC Educational Resources Information Center

Achumba, Ifeyinwa E.; Azzi, Djamel; Stocker, James

2010-01-01

The laboratory component of undergraduate engineering education poses challenges in resource constrained engineering faculties. The cost, time, space and physical presence requirements of the traditional (real) laboratory approach are the contributory factors. These resource constraints may mitigate the acquisition of meaningful laboratory…

Teaching an engine-driven preparation technique to undergraduates: initial observations.

PubMed

Hänni, S; Schönenberger, K; Peters, O A; Barbakow, F

2003-07-01

This paper describes the initial experiences following the introduction of a rotary engine-driven preparation technique into the undergraduate endodontic programme at the Zurich University Dental Centre. Forty third-year students practised the ProFile.04 (PF.04) technique between January and July 2001 in a preclinical course. Between November 2001 and February 2002, 20 of these students (Group A) root-treated 51 teeth in their clinical course using either PF.04, the balanced force technique (BFT) or a combination of both. The second group of 20 students (Group B) similarly treated another 36 randomly selected teeth between April and July 2002. Types of teeth treated by the students and the canal preparation techniques were recorded. The students also completed a short questionnaire, evaluating their opinions of the new course. Of the 87 teeth endodontically treated during the clinical course, 34, 14 and 39 were shaped using PF.04 alone, a combination of PF.04 and BFT and BFT alone, respectively. No rotary instruments were fractured during the 1-year clinical course, although some instruments were fractured during the preclinical laboratory course. Overall, the students rated the rotary technique as positive. A rotary technique was successfully introduced into an undergraduate endodontic programme (this will be continued in the foreseeable future). However, the continuity between the preclinical and the clinical courses was poor as a result of the constraints of the general teaching programme.

Elementary teachers' mental models of engineering design processes: A comparison of two communities of practice

NASA Astrophysics Data System (ADS)

McMahon, Ann P.

Educating K-12 students in the processes of design engineering is gaining popularity in public schools. Several states have adopted standards for engineering design despite the fact that no common agreement exists on what should be included in the K-12 engineering design process. Furthermore, little pre-service and in-service professional development exists that will prepare teachers to teach a design process that is fundamentally different from the science teaching process found in typical public schools. This study provides a glimpse into what teachers think happens in engineering design compared to articulated best practices in engineering design. Wenger's communities of practice work and van Dijk's multidisciplinary theory of mental models provide the theoretical bases for comparing the mental models of two groups of elementary teachers (one group that teaches engineering and one that does not) to the mental models of design engineers (including this engineer/researcher/educator and professionals described elsewhere). The elementary school teachers and this engineer/researcher/educator observed the design engineering process enacted by professionals, then answered questions designed to elicit their mental models of the process they saw in terms of how they would teach it to elementary students. The key finding is this: Both groups of teachers embedded the cognitive steps of the design process into the matrix of the social and emotional roles and skills of students. Conversely, the engineers embedded the social and emotional aspects of the design process into the matrix of the cognitive steps of the design process. In other words, teachers' mental models show that they perceive that students' social and emotional communicative roles and skills in the classroom drive their cognitive understandings of the engineering process, while the mental models of this engineer/researcher/educator and the engineers in the video show that we perceive that cognitive understandings of the engineering process drive the social and emotional roles and skills used in that process. This comparison of mental models with the process that professional designers use defines a problem space for future studies that investigate how to incorporate engineering practices into elementary classrooms. Recommendations for engineering curriculum development and teacher professional development based on this study are presented.

Outreach to Scientists and Engineers at the Hanford Technical Library

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buxton, Karen A.

Staff at the Hanford Technical Library has developed a suite of programs designed to help busy researchers at the Pacific Northwest National Laboratory (PNNL) make better use of library products and services. Programs include formal training classes, one-on-one consultations, and targeted email messages announcing new materials to researchers in specific fields. A staple of outreach has been to teach classes to library clients covering research tools in their fields. These classes started out in the library classroom and then expanded to other venues around PNNL. Class surveys indicated that many researchers desired a practical approach to learning rather than themore » traditional lecture format. The library instituted “Library Learning Day” and hosted classes in the PNNL computer training room to provide lab employees with a hands-on learning experience. Classes are generally offered at noon and lab staff attends classes on their lunch hour. Many just do not have time to spend a full hour in training. Library staff added some experimental half-hour mini classes in campus buildings geared to the projects and interests of researchers there to see if this format was more appealing. As other programs have developed librarians are teaching fewer classes but average attendance figures has remained fairly stable from 2005-2007. In summer of 2004 the library began the Traveling Librarian program. Librarians call-on groups and individuals in 24 buildings on the Richland Washington campus. Five full-time and two part-time librarians are involved in the program. Librarians usually send out email announcements prior to visits and encourage scientists and engineers to make appointments for a brief 15 minute consultation in the researcher’s own office. During the meeting lab staff learn about products or product features that can help them work more productively. Librarians also make cold calls to staff that do not request a consultation and may not be making full use of the library. Scientists and engineers who require longer sessions can arrange half-hour training appointments in the researcher’s own office or at the library. Since the program was implemented staff made 165 visits to 1249 laboratory staff including some repeat consultation requests. New acquisitions lists are sent to individuals and groups that would be interested in recent journal, database, and books purchases. These lists are topic specific and targeted to groups and individuals with an interest in the field. For example newly acquired engineering resources are targeted at engineering groups. The new acquisitions list for engineering began mid year in 2005. An analysis of circulation statistics for engineering books in fiscal year 2005, 2006, and 2007 show that circulation increased each year with 2007 circulation nearly double that of 2005. This took place when overall circulation rose in FY06 but fell slightly in FY07. Outreach strategies tailored and individualized can be effective. Offering multiple outreach options offers researchers different ways to interact with library staff and services.« less

Students' Attitude towards STEM Education

ERIC Educational Resources Information Center

Popa, Roxana-Alexandra; Ciascai, Liliana

2017-01-01

STEM is the acronym of Science, Technology, Engineering, and Mathematics fields. STEM education refers both to teaching and learning in the above-mentioned disciplines, but especially to teaching and learning a new discipline based on the integration of Science, Technology, Engineering, and Mathematics. The present survey aims to investigate the…

Web Tools: Keeping Learners on Pace

ERIC Educational Resources Information Center

Kosloski, Mickey

2016-01-01

One of the greatest challenges in teaching technology and engineering is pacing. Some students grasp new technological concepts quickly, while others need repetition and may struggle to keep pace. This poses an obstacle for the technology and engineering teacher, and is particularly true when teaching students to build a website. However, there…

Environmental Engineering Teaching Reference Community.

ERIC Educational Resources Information Center

Bell, John M.; Brenchley, David L.

Dawson, Fairfax County/U.S.A. is a hypothetical community developed by the authors as a teaching aid for undergraduate and graduate courses in environmental engineering, providing a context for problem solving and role playing. It was contrived to provide students opportunities to: (1) identify important community relationships, (2) appreciate the…

Control Engineering, System Theory and Mathematics: The Teacher's Challenge

ERIC Educational Resources Information Center

Zenger, K.

2007-01-01

The principles, difficulties and challenges in control education are discussed and compared to the similar problems in the teaching of mathematics and systems science in general. The difficulties of today's students to appreciate the classical teaching of engineering disciplines, which are based on rigorous and scientifically sound grounds, are…

Enhancement of Teaching and Learning of the Fundamentals of Nuclear Engineering Using Multimedia Courseware.

ERIC Educational Resources Information Center

Keyvan, Shahla A.; Pickard, Rodney; Song, Xiaolong

1997-01-01

Computer-aided instruction incorporating interactive multimedia and network technologies can boost teaching effectiveness and student learning. This article describes the development and implementation of network server-based interactive multimedia courseware for a fundamental course in nuclear engineering. A student survey determined that 80% of…

Teaching Engineering Design Through Paper Rockets

ERIC Educational Resources Information Center

Welling, Jonathan; Wright, Geoffrey A.

2018-01-01

The paper rocket activity described in this article effectively teaches the engineering design process (EDP) by engaging students in a problem-based learning activity that encourages iterative design. For example, the first rockets the students build typically only fly between 30 and 100 feet. As students test and evaluate their rocket designs,…

Student Achievement and Retention: Can Professional Development Programs Help Faculty GRASP It?

ERIC Educational Resources Information Center

McShannon, Judy; Hynes, Patricia

2005-01-01

Many faculty developers have difficulty involving engineering and science faculty in instructional development. Engineering professors are particularly quick to discount the relevance of teaching workshops, and many argue teaching methods presented in workshops lead to lower standards and inflated grades. This paper presents a successful…

Teaching, Learning and Evaluation Techniques in the Engineering Courses.

ERIC Educational Resources Information Center

Vermaas, Luiz Lenarth G.; Crepaldi, Paulo Cesar; Fowler, Fabio Roberto

This article presents some techniques of professional formation from the Petra Model that can be applied in Engineering Programs. It shows its philosophy, teaching methods for listening, making abstracts, studying, researching, team working and problem solving. Some questions regarding planning and evaluation, based in the model are, as well,…

Soils and Foundations: A Syllabus.

ERIC Educational Resources Information Center

Long, Melvin J.

The teaching guide and course outline for a 12-week course in soils and foundations is designed to help student technicians in a two-year associate degree civil engineering technology program to obtain entry level employment as highway engineering aides, soil testing technicians, soil mappers, or construction inspectors. The seven teaching units…

Engineering Lecturers' Views on CLIL and EMI

ERIC Educational Resources Information Center

Aguilar, Marta

2017-01-01

The present study aims to shed some light on how engineering lecturers teaching in English at a Spanish university view their work (teaching goals) within the current European internationalisation trend of offering courses and master programmes in English. A questionnaire where content and language integrated learning (CLIL) and English-medium…

Exploration of Engineering Students' Values with Respect to Behaviors in Group Work

ERIC Educational Resources Information Center

Nagel, Robert L.; Pappas, Eric C.; Swain, Matthew S.; Hazard, Gretchen A.

2015-01-01

In order to train young professionals, instructional methodologies in engineering need not only teach students knowledge, but must also instill the values and teach the behaviors--"competencies" students can demonstrate--required of professional practice. Herein, we focus on understanding the values and behaviors of students with respect…

TEACHING ENGINEERING DESIGN, A STUDY OF JOBSHOP.

ERIC Educational Resources Information Center

ENTWISLE, DORIS R.; HUGGINS, W.H.

THE USE OF A COMPUTER PROGRAM BY ENGINEERING STUDENTS TO SIMULATE A JOB SHOP THAT MANUFACTURES ELECTRONIC DEVICES HAS INDICATED THAT SIMULATION METHODS OFFER REALISTIC ASSISTANCE IN TEACHING. EACH STUDENT IN THE STUDY SUBMITTED SPECIFICATIONS FOR A CIRCUIT DESIGN AND, FROM THE COMPUTER, RECEIVED PERFORMANCE ASSESSMENTS OF THE CIRCUIT WHICH…

Teaching Embedded System Concepts for Technological Literacy

ERIC Educational Resources Information Center

Winzker, M.; Schwandt, A.

2011-01-01

A basic understanding of technology is recognized as important knowledge even for students not connected with engineering and computer science. This paper shows that embedded system concepts can be taught in a technological literacy course. An embedded system teaching block that has been used in an electronics module for non-engineers is…

The Problem with Reform from the Bottom up: Instructional practises and teacher beliefs of graduate teaching assistants following a reform-minded university teacher certificate programme

NASA Astrophysics Data System (ADS)

Addy, Tracie M.; Blanchard, Margaret R.

2010-05-01

Reform-minded practices are widely encouraged during pre-service science teacher education in concert with national reform documents. This contrasts to the nature of instruction within university science laboratories in which pre-service teachers enrol, which are largely confirmatory in nature. Undergraduate science laboratories are taught predominantly by graduate teaching assistants (GTAs) with minimal teacher preparation. The purpose of this mixed-methods study is to investigate the instructional practices and teacher beliefs of eight GTAs at a university with very high research activity who completed a reform-minded Teacher Certificate Programme, asking: What are their beliefs about teaching? How are their practices described? Do their beliefs and practices differ from one another? Do their teaching beliefs correspond with their practices? Findings indicate that GTAs held moderately reform-minded "transitional" beliefs of teaching following the programme, yet displayed fairly traditional instruction. Cross-case findings highlight similar patterns across subscales of the RTOP that draw attention to underlying constraints of the laboratory curriculum structure. We suggest that GTA professional development is best undertaken concurrent with laboratory course revision.

Promoting Inquiry-Based Teaching in Laboratory Courses: Are We Meeting the Grade?

PubMed Central

Butler, Amy; Burke da Silva, Karen

2014-01-01

Over the past decade, repeated calls have been made to incorporate more active teaching and learning in undergraduate biology courses. The emphasis on inquiry-based teaching is especially important in laboratory courses, as these are the courses in which students are applying the process of science. To determine the current state of research on inquiry-based teaching in undergraduate biology laboratory courses, we reviewed the recent published literature on inquiry-based exercises. The majority of studies in our data set were in the subdisciplines of biochemistry, cell biology, developmental biology, genetics, and molecular biology. In addition, most exercises were guided inquiry, rather than open ended or research based. Almost 75% of the studies included assessment data, with two-thirds of these studies including multiple types of assessment data. However, few exercises were assessed in multiple courses or at multiple institutions. Furthermore, assessments were rarely based on published instruments. Although the results of the studies in our data set show a positive effect of inquiry-based teaching in biology laboratory courses on student learning gains, research that uses the same instrument across a range of courses and institutions is needed to determine whether these results can be generalized. PMID:25185228

Active-learning laboratory session to teach the four M's of diabetes care.

PubMed

Darbishire, Patricia L; Plake, Kimberly S; Nash, Christiane L; Shepler, Brian M

2009-04-07

To implement an active-learning methodology for teaching diabetes care to pharmacy students and evaluate its effectiveness. Laboratory instruction was divided into 4 primary areas of diabetes care, referred to by the mnemonic, the 4 M's: meal planning, motion, medication, and monitoring. Students participated in skill-based learning laboratory stations and in simulated patient experiences. A pretest, retrospective pretest, and posttest were administered to measure improvements in students' knowledge about diabetes and confidence in providing care to diabetes patients. Students knowledge of and confidence in each area assessed improved. Students enjoyed the laboratory session and felt it contributed to their learning. An active-learning approach to teaching diabetes care allowed students to experience aspects of the disease from the patient's perspective. This approach will be incorporated in other content areas.

Using Crickets to Introduce Neurophysiology to Early Undergraduate Students

PubMed Central

Dagda, Ruben K.; Thalhauser, Rachael M.; Dagda, Raul; Marzullo, Timothy C.; Gage, Gregory J.

2013-01-01

Anatomy and physiology instructors often face the daunting task of teaching the principles of neurophysiology as part of a laboratory course with very limited resources. Teaching neurophysiology can be a difficult undertaking as sophisticated electrophysiology and data acquisition equipment is often financially out-of-reach for two-year institutions, and for many preparations, instructors need to be highly skilled in electrophysiology techniques when teaching hands-on laboratories. In the absence of appropriate laboratory tools, many undergraduate students have difficulty understanding concepts related to neurophysiology. The cricket can serve as a reliable invertebrate model to teach the basic concepts of neurophysiology in the educational laboratory. In this manuscript, we describe a series of hands-on, demonstrative, technologically simple, and affordable laboratory activities that will help undergraduate students gain an understanding of the principles of neurophysiology. By using the cerci ganglion and leg preparation, students can quantify extracellular neural activity in response to sensory stimulation, understand the principles of rate coding and somatotopy, perform electrical microstimulation to understand the threshold of sensory stimulation, and do pharmacological manipulation of neuronal activity. We describe the utility of these laboratory activities, provide a convenient protocol for quantifying extracellular recordings, and discuss feedback provided by undergraduate students with regards to the quality of the educational experience after performing the lab activities. PMID:24319394

Laboratory Manual, Electrical Engineering 25.

ERIC Educational Resources Information Center

Syracuse Univ., NY. Dept. of Electrical Engineering.

Developed as part of a series of materials in the electrical engineering sequence developed under contract with the United States Office of Education, this laboratory manual provides nine laboratory projects suitable for a second course in electrical engineering. Dealing with resonant circuits, electrostatic fields, magnetic devices, and…

40 CFR 1065.920 - PEMS Calibrations and verifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Field Testing and Portable Emission Measurement Systems § 1065... verification. The verification consists of operating an engine over a duty cycle in the laboratory and... by laboratory equipment as follows: (1) Mount an engine on a dynamometer for laboratory testing...

Accelerator-based techniques for the support of senior-level undergraduate physics laboratories

NASA Astrophysics Data System (ADS)

Williams, J. R.; Clark, J. C.; Isaacs-Smith, T.

2001-07-01

Approximately three years ago, Auburn University replaced its aging Dynamitron accelerator with a new 2MV tandem machine (Pelletron) manufactured by the National Electrostatics Corporation (NEC). This new machine is maintained and operated for the University by Physics Department personnel, and the accelerator supports a wide variety of materials modification/analysis studies. Computer software is available that allows the NEC Pelletron to be operated from a remote location, and an Internet link has been established between the Accelerator Laboratory and the Upper-Level Undergraduate Teaching Laboratory in the Physics Department. Additional software supplied by Canberra Industries has also been used to create a second Internet link that allows live-time data acquisition in the Teaching Laboratory. Our senior-level undergraduates and first-year graduate students perform a number of experiments related to radiation detection and measurement as well as several standard accelerator-based experiments that have been added recently. These laboratory exercises will be described, and the procedures used to establish the Internet links between our Teaching Laboratory and the Accelerator Laboratory will be discussed.

NASA's Suborbital Missions Teach Engineering and Technology: Goddard Space Flight Center's Wallops Flight Facility

NASA Technical Reports Server (NTRS)

Winterton, Joyce L.

2016-01-01

A 50 minute-workshop based on NASA publicly available information will be conducted at the International Technology and Engineering Educator Association annual conference. Attendees will include middle and high school teachers and university teacher educators. Engineering and technology are essential to NASA's suborbital missions including sounding rockets, scientific balloon and airborne science. The attendees will learn how to include NASA information on these missions in their teaching.

Thermal Cameras in School Laboratory Activities

ERIC Educational Resources Information Center

Haglund, Jesper; Jeppsson, Fredrik; Hedberg, David; Schönborn, Konrad J.

2015-01-01

Thermal cameras offer real-time visual access to otherwise invisible thermal phenomena, which are conceptually demanding for learners during traditional teaching. We present three studies of students' conduction of laboratory activities that employ thermal cameras to teach challenging thermal concepts in grades 4, 7 and 10-12. Visualization of…

Graduate Teaching Assistants' Epistemological and Metacognitive Development

ERIC Educational Resources Information Center

Sandi-Urena, Santiago; Cooper, Melanie M.; Gatlin, Todd A.

2011-01-01

Research in general chemistry laboratory instruction has rarely focused on the impact of the learning environment on the graduate teaching assistants (GTAs). We decided to investigate the effect that facilitating a well established cooperative problem-based chemistry laboratory has on GTAs' epistemological and metacognitive development, and how…

Does Agricultural Mechanics Laboratory Size Affect Agricultural Education Teachers' Job Satisfaction?

ERIC Educational Resources Information Center

Byrd, Alex Preston; Anderson, Ryan G.; Paulsen, Thomas H.

2015-01-01

Secondary agricultural education teachers were surveyed to examine if a relationship existed between the physical attributes of agricultural mechanics laboratories and agricultural education teachers' enjoyment of teaching agricultural mechanics. Teachers also indicated their competence to teach courses other than agricultural mechanics within the…

Enhancing Teaching Assistants' (TAs') Inquiry Teaching by Means of Teaching Observations and Reflective Discourse

ERIC Educational Resources Information Center

Miller, Kristen; Brickman, Peggy; Oliver, J. Steve

2014-01-01

Recent education reform efforts advocate teaching the process of science (inquiry) in undergraduate lecture and laboratory classes. To meet this challenge, professional development for the graduate student instructors (teaching assistants, or TAs) often assigned to teach these classes is needed. This study explored the implementation of an…

76 FR 77559 - Agency Information Collection Activities: Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-13

... system. The Noyce Program encourages talented science, technology, engineering, and mathematics (STEM... introduction to a possible career in teaching. Under the NSF Teaching Fellowship and Master Teaching Fellowship...

Engineering Student's Ethical Awareness and Behavior: A New Motivational Model.

PubMed

Bairaktarova, Diana; Woodcock, Anna

2017-08-01

Professional communities are experiencing scandals involving unethical and illegal practices daily. Yet it should not take a national major structure failure to highlight the importance of ethical awareness and behavior, or the need for the development and practice of ethical behavior in engineering students. Development of ethical behavior skills in future engineers is a key competency for engineering schools as ethical behavior is a part of the professional identity and practice of engineers. While engineering educators have somewhat established instructional methods to teach engineering ethics, they still rely heavily on teaching ethical awareness, and pay little attention to how well ethical awareness predicts ethical behavior. However the ability to exercise ethical judgement does not mean that students are ethically educated or likely to behave in an ethical manner. This paper argues measuring ethical judgment is insufficient for evaluating the teaching of engineering ethics, because ethical awareness has not been demonstrated to translate into ethical behavior. The focus of this paper is to propose a model that correlates with both, ethical awareness and ethical behavior. This model integrates the theory of planned behavior, person and thing orientation, and spheres of control. Applying this model will allow educators to build confidence and trust in their students' ability to build a professional identity and be prepared for the engineering profession and practice.

Enhancing Engineering Education through Engineering Management

ERIC Educational Resources Information Center

Pence, Kenneth R.; Rowe, Christopher J.

2012-01-01

Engineering Management courses are added to a traditional engineering curriculum to enhance the value of an undergraduate's engineering degree. A four-year engineering degree often leaves graduates lacking in business and management acumen. Engineering management education covers topics enhancing the value of new graduates by teaching management…

Science, Technology, Engineering, and Mathematics Graduate Teaching Assistants Teaching Self-Efficacy

ERIC Educational Resources Information Center

DeChenne, Sue Ellen; Enochs, Larry G.; Needham, Mark

2012-01-01

The graduate experience is a critical time for development of academic faculty, but often there is little preparation for teaching during the graduate career. Teaching self-efficacy, an instructor's belief in his or her ability to teach students in a specific context, can help to predict teaching behavior and student achievement, and can be used…

Instructional Strategies and Course Design for Teaching Statistics Online: Perspectives from Online Students

ERIC Educational Resources Information Center

Yang, Dazhi

2017-01-01

Background: Teaching online is a different experience from that of teaching in a face-to-face setting. Knowledge and skills developed for teaching face-to-face classes are not adequate preparation for teaching online. It is even more challenging to teach science, technology, engineering and math (STEM) courses completely online because these…

Annotated bibliography of software engineering laboratory literature

NASA Technical Reports Server (NTRS)

Groves, Paula; Valett, Jon

1990-01-01

An annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory is given. More than 100 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. This document has been updated and reorganized substantially since the original version (SEL-82-006, November 1982). All materials have been grouped into eight general subject areas for easy reference: the Software Engineering Laboratory; the Software Engineering Laboratory-software development documents; software tools; software models; software measurement; technology evaluations; Ada technology; and data collection. Subject and author indexes further classify these documents by specific topic and individual author.

Annotated bibliography of Software Engineering Laboratory literature

NASA Technical Reports Server (NTRS)

Morusiewicz, Linda; Valett, Jon

1993-01-01

This document is an annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory. Nearly 200 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. This document has been updated and reorganized substantially since the original version (SEL-82-006, November 1982). All materials have been grouped into eight general subject areas for easy reference: the Software Engineering Laboratory; the Software Engineering Laboratory: software development documents; software tools; software models; software measurement; technology evaluations; Ada technology; and data collection. This document contains an index of these publications classified by individual author.

Idaho National Engineering Laboratory, Test Area North, Hangar 629 -- Photographs, written historical and descriptive data

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1994-12-31

The report describes the history of the Idaho National Engineering Laboratory`s Hangar 629. The hangar was built to test the possibility of linking jet engine technology with nuclear power. The history of the project is described along with the development and eventual abandonment of the Flight Engine Test hangar. The report contains historical photographs and architectural drawings.

What Chemistry To Teach Engineers?

ERIC Educational Resources Information Center

Hawkes, Stephen J.

2000-01-01

Examines possible general chemistry topics that would be most relevant and practical for engineering majors. Consults the Accreditation Board for Engineering and Technology (ABET), engineering textbooks, texts from other required subjects, and practicing engineers for recommendations. (Contains 24 references.) (WRM)

Staff and students' perceptions and experiences of teaching and assessment in Clinical Skills Laboratories: interview findings from a multiple case study.

PubMed

Houghton, Catherine E; Casey, Dympna; Shaw, David; Murphy, Kathy

2012-08-01

The Clinical Skills Laboratory has become an essential structure in nurse education and several benefits of its use have been identified. However, the literature identifies the need to examine the transferability of skills learned there into the reality of practice. This research explored the role of the Clinical Skills Laboratory in preparing nursing students for the real world of practice. This paper focuses specifically on the perceptions of the teaching and assessment strategies employed there. Qualitative multiple case study design. Five case study sites. Interviewees (n=58) included academic staff, clinical staff and nursing students. Semi-structured interviews. The Clinical Skills Laboratory can provide a pathway to practice and its authenticity is significant. Teaching strategies need to incorporate communication as well as psychomotor skills. Including audio-visual recording into assessment strategies is beneficial. Effective relationships between education institutions and clinical settings are needed to enhance the transferability of the skills learned. The Clinical Skills Laboratory should provide an authentic learning environment, with the appropriate use of teaching strategies. It is crucial that effective links between educators and clinical staff are established and maintained. Copyright © 2011 Elsevier Ltd. All rights reserved.

Fuels and Lubrication Researcher at the Aircraft Engine Research Laboratory

NASA Image and Video Library

1943-08-21

A researcher at the National Advisory Committee for Aeronautics (NACA) Aircraft Engine Research Laboratory studies the fuel ignition process. Improved fuels and lubrication was an area of particular emphasis at the laboratory during World War II. The military sought to use existing types of piston engines in order to get large numbers of aircraft into the air as quickly as possible. To accomplish its goals, however, the military needed to increase the performance of these engines without having to wait for new models or extensive redesigns. The Aircraft Engine Research Laboratory was called on to lead this effort. The use of superchargers successfully enhanced engine performance, but the resulting heat increased engine knock [fuel detonation] and structural wear. These effects could be offset with improved cooling, lubrication, and fuel mixtures. The NACA researchers in the Fuels and Lubrication Division concentrated on new synthetic fuels, higher octane fuels, and fuel-injection systems. The laboratory studied 16 different types of fuel blends during the war, including extensive investigations of triptane and xylidine.

Stirling Laboratory Research Engine: Preprototype configuration report

NASA Technical Reports Server (NTRS)

Hoehn, F. W.

1982-01-01

The concept of a simple Stirling research engine that could be used by industrial, university, and government laboratories was studied. The conceptual and final designs, hardware fabrication and the experimental validation of a preprototype stirling laboratory research engine (SLRE) were completed. Also completed was a task to identify the potential markets for research engines of this type. An analytical effort was conducted to provide a stirling cycle computer model. The versatile engine is a horizontally opposed, two piston, single acting stirling engine with a split crankshaft drive mechanism; special instrumentation is installed at all component interfaces. Results of a thermodynamic energy balance for the system are reported. Also included are the engine performance results obtained over a range of speeds, working pressures, phase angles and gas temperatures. The potential for a stirling research engine to support the laboratory requirements of educators and researchers was demonstrated.

The Engineering Design Process: Conceptions Along the Learning-to-Teach Continuum

NASA Astrophysics Data System (ADS)

Iveland, Ashley

In this study, I sought to identify differences in the views and understandings of engineering design among individuals along the learning-to-teach continuum. To do so, I conducted a comprehensive review of literature to determine the various aspects of engineering design described in the fields of professional engineering and engineering education. Additionally, I reviewed literature on the methods used in teaching engineering design at the secondary (grade 7-12) level - to describe the various models used in classrooms, even before the implementation of the Next Generation Science Standards (NGSS Lead States, 2013). Last, I defined four groups along the learning-to-teach continuum: prospective, preservice, and practicing teachers, as well as teacher educators. The context of this study centered around a California public university, including an internship program where undergraduates engaged with practicing mentor teachers in science and engineering teaching at local high schools, and a teacher education program where secondary science preservice teachers and the teacher educators who taught them participated. Interviews were conducted with all participants to gain insights into their views and understandings of engineering design. Prospective and preservice teachers were interviewed multiple times throughout the year and completed concept maps of the engineering design process multiple times as well; practicing teachers and teacher educators were interviewed once. Three levels of analyses were conducted. I identified 30 aspects of engineering discussed by participants. Through phenomenographic methods, I also constructed six conceptual categories for engineering design to organize those aspects most commonly discussed. These categories were combined to demonstrate a participant's view of engineering design (e.g., business focused, human centered, creative, etc.) as well as their complexity of understanding of engineering design overall (the more categories their ideas fit within, the more complex their understanding was thought to be). I found that the most commonly referenced aspects of engineering design were in line with the three main dimensions described in the Next Generation Science Standards (NGSS Lead States, 2013). I also found that the practicing teacher participants overall conveyed the most complex and integrated understandings of engineering design, with the undergraduate, prospective teachers not far behind. One of the most important factors related to a more integrated understanding of engineering design was having formal engineering experience, especially in the form of conducting engineering research or having been a professional engineer. Further, I found that female participants were more likely than their male counterparts to view engineering as having a human element--recognizing the need to collaborate with others throughout the process and the need to think about the potential user of the product the engineer is solving the problem for. These findings suggest that prior experience with engineering, and not experience in the classroom or with engineering education, tends to lead to a deeper, more authentic view of engineering. Finally, I close with a discussion of the overall findings, limitations of the study, potential implications, and future work.

Enhanced virtual microscopy for collaborative education.

PubMed

Triola, Marc M; Holloway, William J

2011-01-26

Curricular reform efforts and a desire to use novel educational strategies that foster student collaboration are challenging the traditional microscope-based teaching of histology. Computer-based histology teaching tools and Virtual Microscopes (VM), computer-based digital slide viewers, have been shown to be effective and efficient educational strategies. We developed an open-source VM system based on the Google Maps engine to transform our histology education and introduce new teaching methods. This VM allows students and faculty to collaboratively create content, annotate slides with markers, and it is enhanced with social networking features to give the community of learners more control over the system. We currently have 1,037 slides in our VM system comprised of 39,386,941 individual JPEG files that take up 349 gigabytes of server storage space. Of those slides 682 are for general teaching and available to our students and the public; the remaining 355 slides are used for practical exams and have restricted access. The system has seen extensive use with 289,352 unique slide views to date. Students viewed an average of 56.3 slides per month during the histology course and accessed the system at all hours of the day. Of the 621 annotations added to 126 slides 26.2% were added by faculty and 73.8% by students. The use of the VM system reduced the amount of time faculty spent administering the course by 210 hours, but did not reduce the number of laboratory sessions or the number of required faculty. Laboratory sessions were reduced from three hours to two hours each due to the efficiencies in the workflow of the VM system. Our virtual microscope system has been an effective solution to the challenges facing traditional histopathology laboratories and the novel needs of our revised curriculum. The web-based system allowed us to empower learners to have greater control over their content, as well as the ability to work together in collaborative groups. The VM system saved faculty time and there was no significant difference in student performance on an identical practical exam before and after its adoption. We have made the source code of our VM freely available and encourage use of the publically available slides on our website.

Waterless Condensers for the Teaching Laboratory: An Adaptation of Traditional Glassware

ERIC Educational Resources Information Center

Baum, Erich W.; Esteb, John J.; Wilson, Anne M.

2014-01-01

A simple adaptation of traditional "chemistry kit" condensers for the organic chemistry teaching laboratory is described. These waterless condensers have been employed safely with most solvents. They can be easily fabricated, stored, and used in the same manner as water-cooled condensers. These condensers were utilized in several…

Reinvigorating Introductory Biology: A Theme-based, Investigative Approach To Teaching Biology Majors.

ERIC Educational Resources Information Center

Norton, Cynthia G.; Gildensoph, Lynne H.; Phillips, Martha M.; Wygal, Deborah D.; Olson, Kurt H.; Pellegrini, John J.; Tweeten, Kathleen A.

1997-01-01

Describes the reform of an introductory biology curriculum to reverse high attrition rates. Objectives include fostering self-directed learning, emphasizing process over content, and offering laboratory experiences that model the way to acquire scientific knowledge. Teaching methods include discussion, group mentoring, laboratory sections, and…

Remote Teaching Experiments on Magnetic Domains in Thin Films

ERIC Educational Resources Information Center

Dobrogowski, W.; Maziewski, A.; Zablotskii, V.

2007-01-01

We describe our experience in building a remote laboratory for teaching magnetic domains. Fulfilling the proposed on-line experiments, students can observe and study magnetization processes that are often difficult to explain with written material. It is proposed that networks of remotely accessible laboratories could be integrated in the Global…

A Cost-Effective Two-Part Experiment for Teaching Introductory Organic Chemistry Techniques

ERIC Educational Resources Information Center

Sadek, Christopher M.; Brown, Brenna A.; Wan, Hayley

2011-01-01

This two-part laboratory experiment is designed to be a cost-effective method for teaching basic organic laboratory techniques (recrystallization, thin-layer chromatography, column chromatography, vacuum filtration, and melting point determination) to large classes of introductory organic chemistry students. Students are exposed to different…

Teaching and Learning Distillation in Chemistry Laboratory Courses.

ERIC Educational Resources Information Center

van Keulen, Hanno; And Others

Distillation in the chemistry laboratory is an essential part of a practicing chemists' and a chemistry educators' work. Nevertheless, regardless of the degree of importance in each of the aforementioned professions, few educational studies on teaching and learning distillation exist. In an effort to rectify this oversight, the Department of…

A Novel Laboratory Activity for Teaching about the Evolution of Multicellularity

ERIC Educational Resources Information Center

Ratcliff, William C.; Raney, Allison; Westreich, Sam; Cotner, Sehoya

2014-01-01

The evolution of complexity remains one of the most challenging topics in biology to teach effectively. We present a novel laboratory activity, modeled on a recent experimental breakthrough, in which students experimentally evolve simple multicellularity using single-celled yeast ("Saccharomyces cerevisiae"). By simply selecting for…

CRITTERS! A Realistic Simulation for Teaching Evolutionary Biology

ERIC Educational Resources Information Center

Latham, Luke G., II; Scully, Erik P.

2008-01-01

Evolutionary processes can be studied in nature and in the laboratory, but time and financial constraints result in few opportunities for undergraduate and high school students to explore the agents of genetic change in populations. One alternative to time consuming and expensive teaching laboratories is the use of computer simulations. We…

Using a Thematic Laboratory-Centered Curriculum to Teach General Chemistry

ERIC Educational Resources Information Center

Hopkins, Todd A.; Samide, Michael

2013-01-01

This article describes an approach to general chemistry that involves teaching chemical concepts in the context of two thematic laboratory modules: environmental remediation and the fate of pharmaceuticals in the environment. These modules were designed based on active-learning pedagogies and involve multiple-week projects that dictate what…

An Investigative, Cooperative Learning Approach for General Chemistry Laboratories

ERIC Educational Resources Information Center

Díaz-Vázquez, Liz M.; Montes, Barbara Casañas; Echevarría Vargas, Ileabett M.; Hernandez-Cancel, Griselle; Gonzalez, Fernando; Molina, Anna M.; Morales-Cruz, Moraima; Torres-Díaz, Carlos M.; Griebenow, Kai

2012-01-01

The integration of research and education is an essential component of our university's teaching philosophy. Recently, we made a curricular revision to facilitate such an approach in the General Chemistry Laboratory, to teach students that investigative approaches are at the core of sciences. The curriculum revision included new interdisciplinary…

Continuous Flow Science in an Undergraduate Teaching Laboratory: Bleach-Mediated Oxidation in a Biphasic System

ERIC Educational Resources Information Center

Kairouz, Vanessa; Collins, Shawn K.

2018-01-01

An undergraduate teaching laboratory experiment involving a continuous flow, bleach-mediated oxidation of aldehydes under biphasic conditions was developed that allowed students to explore concepts of mixing or mass transport, solvent sustainability, biphasic reactions, phase transfer catalysis, and continuous flow chemistry.

Engineering students' and faculty perceptions of teaching methods and the level of faculty involvement that promotes academic success

NASA Astrophysics Data System (ADS)

Karpilo, Lacy N.

Student academic success is a top priority of higher education institutions in the United States and the trend of students leaving school prior to finishing their degree is a serious concern. Accountability has become a large part of university and college ratings and perceived success. Retention is one component of the accountability metrics used by accreditation agencies. In addition, there are an increasing number of states allocating funds based in part on retention (Seidman, 2005). Institutions have created initiatives, programs, and even entire departments to address issues related to student academic success to promote retention. Universities and colleges have responded by focusing on methods to retain and better serve students. Retention and student academic success is a primary concern for high education institutions; however, engineering education has unique retention issues. The National Science Board (2004) reports a significant decline in the number of individuals in the United States who are training to become engineers, despite the fact that the number of jobs that utilize an engineering background continues to increase. Engineering education has responded to academic success issues by changing curriculum and pedagogical methods (Sheppard, 2001). This descriptive study investigates the perception of engineering students and faculty regarding teaching methods and faculty involvement to create a picture of what is occurring in engineering education. The population was the engineering students and faculty of Colorado State University's College of Engineering. Data from this research suggests that engaging teaching methods are not being used as often as research indicates they should and that there is a lack of student-faculty interaction outside of the classroom. This research adds to the breadth of knowledge and understanding of the current environment of engineering education. Furthermore, the data allows engineering educators and other higher education professionals to gain insight into the teaching methods currently being utilized in engineering and reinforces the importance of student-faculty interaction and thus facilitating the creation of programs or initiatives to improve student academic success.

Project support of practical training in biophysics.

PubMed

Mornstein, V; Vlk, D; Forytkova, L

2006-01-01

The Department of Biophysics ensures practical training in biophysics and related subjects for students of medical and health study programmes. Demonstrations of medical technology are an important part of this training. Teaching for Faculty of Sciences in biophysical study programmes becomes also very important. Some lectures and demonstrations of technology are involved, but the practical trainig is missing. About 1 mil. CZK for additional laboratory equipment was obtained from the HEIDF project No. 1866/ 2005 "The demonstration and measuring technology for education in medical biophysics and radiological physics" for measuring system DEWETRON for high frequency signal analysis, Fluke Ti30 IR camera, PM 9000B patient monitor, ARSENAL AF 1 fluorescence microscope, and Nikon Coolpix 4500 digital camera with accessories for microphotography. At the present time, further financial resources are being provided by a development project of Ministry of Education "Inter-university co-operation in biomedical technology and engineering using top technologies" in total amount of almost 5 mil CZK, whereas over 2 mil CZK from this project are reserved for student laboratory equipment. The main goal of this project is to ensure the participation of Medical Faculty in educational co-operation in the biomedical technology and engineering, namely with the Faculty of Electrical Engineering and Communication (FEEC), Brno University of Technology. There will be taught those areas of biophysics which are not covered by FEEC, thus forming a separate subject "General Biophysics". The following instruments will be installed: UV-VIS spectrophotometers, rotation viscometers, tensiometers, microscopes with digital image processing, cooled centrifuge, optical benches, and some smaller instruments for practical measurements.

Student teaching and research laboratory focusing on brain-computer interface paradigms--A creative environment for computer science students.

PubMed

Rutkowski, Tomasz M

2015-08-01

This paper presents an applied concept of a brain-computer interface (BCI) student research laboratory (BCI-LAB) at the Life Science Center of TARA, University of Tsukuba, Japan. Several successful case studies of the student projects are reviewed together with the BCI Research Award 2014 winner case. The BCI-LAB design and project-based teaching philosophy is also explained. Future teaching and research directions summarize the review.

Launching partnership in optics and photonics education between University of Rochester and Moscow Engineering Physics Institute NRNU MEPhI

NASA Astrophysics Data System (ADS)

Lukishova, Svetlana G.; Zavestovskaya, Irina N.; Zhang, Xi-Cheng; Aleshchenko, Yury A.; Konov, Vitaly I.

2017-08-01

A collaboration in education between the oldest and one of the most comprehensive Optics schools in U.S., the Institute of Optics (IO), University of Rochester (UR), and one of the most recognized Russian university, National Research Nuclear University MEPhI (Moscow Engineering Physics Institute) was started in 2015 by signing an agreement on a double-Master's degree program in optics. It was based on earlier collaboration between research groups in both universities. In summer of 2016, nine UR Optics undergraduate students participated with MEPhI students at the International School on Optics and Laser Physics in MEPhI. During five days they were immersed into the world of cutting edge research, technologies and ideas that Russian, European and U.S. scientists offered them. This School also included tours of MEPhI Nanotechnologies and Lasers Centers and Nano-bioengineering Laboratory as well as of scientific laboratories of the leading institutes in optics, photonics and laser physics of the Russian Academy of Sciences. In December of 2015, one MEPhI Master student visited IO UR for one month for a research project with results presented later at a MEPhI conference. Samples prepared by MEPhI researchers are used in IO students teaching laboratories. One Master student from MEPhI is working now towards the Master's degree at the IO UR. In this paper benefits and pitfalls of a cross-border collaboration are discussed as well as different directions of such a collaboration to provide a high-quality specialization for the students of the 21 century which includes international cooperation.

Dr. Johney Green Jr. - Associate Laboratory Director for Mechanical and

Science.gov Websites

Thermal Engineering Sciences | NREL Dr. Johney Green Jr. - Associate Laboratory Director for Mechanical and Thermal Engineering Sciences Dr. Johney Green Jr. - Associate Laboratory Director for Mechanical and Thermal Engineering Sciences A photo of Johney Green In his role, Johney Green oversees early

Annotated bibliography of software engineering laboratory literature

NASA Technical Reports Server (NTRS)

Buhler, Melanie; Valett, Jon

1989-01-01

An annotated bibliography is presented of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory. The bibliography was updated and reorganized substantially since the original version (SEL-82-006, November 1982). All materials were grouped into eight general subject areas for easy reference: (1) The Software Engineering Laboratory; (2) The Software Engineering Laboratory: Software Development Documents; (3) Software Tools; (4) Software Models; (5) Software Measurement; (6) Technology Evaluations; (7) Ada Technology; and (8) Data Collection. Subject and author indexes further classify these documents by specific topic and individual author.

The Microscale Inorganic Laboratory: Safety, Economy and Versatility.

ERIC Educational Resources Information Center

Szafran, Zvi; And Others

1989-01-01

Discussed are four major advantages to the use of microscale laboratories for teaching chemistry. Included are effects on waste generation, laboratory safety, reagent variety, and laboratory efficiency. (CW)

An industrial educational laboratory at Ducati Foundation: narrative approaches to mechanics based upon continuum physics

NASA Astrophysics Data System (ADS)

Corni, Federico; Fuchs, Hans U.; Savino, Giovanni

2018-02-01

This is a description of the conceptual foundations used for designing a novel learning environment for mechanics implemented as an Industrial Educational Laboratory - called Fisica in Moto (FiM) - at the Ducati Foundation in Bologna. In this paper, we will describe the motivation for and design of the conceptual approach to mechanics used in the lab - as such, the paper is theoretical in nature. The goal of FiM is to provide an approach to the teaching of mechanics based upon imaginative structures found in continuum physics suitable to engineering and science. We show how continuum physics creates models of mechanical phenomena by using momentum and angular momentum as primitive quantities. We analyse this approach in terms of cognitive linguistic concepts such as conceptual metaphor and narrative framing of macroscopic physical phenomena. The model discussed here has been used in the didactical design of the actual lab and raises questions for an investigation of student learning of mechanics in a narrative setting.

Uncovering Barriers to Teaching Assistants (TAs) Implementing Inquiry Teaching: Inconsistent Facilitation Techniques, Student Resistance, and Reluctance to Share Control over Learning with Students †

PubMed Central

Gormally, Cara; Sullivan, Carol Subiño; Szeinbaum, Nadia

2016-01-01

Inquiry-based teaching approaches are increasingly being adopted in biology laboratories. Yet teaching assistants (TAs), often novice teachers, teach the majority of laboratory courses in US research universities. This study analyzed the perspectives of TAs and their students and used classroom observations to uncover challenges faced by TAs during their first year of inquiry-based teaching. Our study revealed three insights about barriers to effective inquiry teaching practices: 1) TAs lack sufficient facilitation skills; 2) TAs struggle to share control over learning with students as they reconcile long-standing teaching beliefs with newly learned approaches, consequently undermining their fledgling ability to use inquiry approaches; and 3) student evaluations reinforce teacher-centered behaviors as TAs receive positive feedback conflicting with inquiry approaches. We make recommendations, including changing instructional feedback to focus on learner-centered teaching practices. We urge TA mentors to engage TAs in discussions to uncover teaching beliefs underlying teaching choices and support TAs through targeted feedback and practice. PMID:27158302

An Instructional Consultation Service for Graduate Teaching Assistants.

ERIC Educational Resources Information Center

Habel, J. C.; Graveel, J. G.

1988-01-01

Described is a support program that guides prospective college teachers in teaching an introductory soil science laboratory course. Ideas are presented about the preparation for teaching and concerns of teaching assistants. A table citing classroom observation protocol is included. (RT)

''Math in a Can'': Teaching Mathematics and Engineering Design

ERIC Educational Resources Information Center

Narode, Ronald B.

2011-01-01

Using an apparently simple problem, ''Design a cylindrical can that will hold a liter of milk,'' this paper demonstrates how engineering design may facilitate the teaching of the following ideas to secondary students: linear and non-linear relationships; basic geometry of circles, rectangles, and cylinders; unit measures of area and volume;…

Experimental Economics for Teaching the Functioning of Electricity Markets

ERIC Educational Resources Information Center

Guevara-Cedeno, J. Y.; Palma-Behnke, R.; Uribe, R.

2012-01-01

In the field of electricity markets, the development of training tools for engineers has been extremely useful. A novel experimental economics approach based on a computational Web platform of an electricity market is proposed here for the practical teaching of electrical engineering students. The approach is designed to diminish the gap that…

Microsoft Excel Software Usage for Teaching Science and Engineering Curriculum

ERIC Educational Resources Information Center

Singh, Gurmukh; Siddiqui, Khalid

2009-01-01

In this article, our main objective is to present the use of Microsoft Software Excel 2007/2003 for teaching college and university level curriculum in science and engineering. In particular, we discuss two interesting and fascinating examples of interactive applications of Microsoft Excel targeted for undergraduate students in: 1) computational…

An Exploratory Investigation of Teaching Innovations and Learning Factors in a Lean Manufacturing Systems Engineering Course

ERIC Educational Resources Information Center

Choomlucksana, Juthamas; Doolen, Toni L.

2017-01-01

The use of collaborative activities and simulation sessions in engineering education has been explored previously. However, few studies have investigated the relationship of these types of teaching innovations with other learner characteristics, such as self-efficacy and background knowledge. This study explored the effects of collaborative…

Engineering Graphics and Design Teachers' Understanding and Teaching of Assembly Drawing

ERIC Educational Resources Information Center

Singh-Pillay, Asheena; Sotsaka, Douglas Sibusiso

2017-01-01

This study explored the relationship between teachers' content knowledge and their pedagogical skills, and reports on that relationship in the teaching of Assembly Drawing (AD) in a South African context. Given that Engineering Graphics Design (EGD) learners perform poorly in the AD section of the matriculation examination, we need to understand…

"Star Power" for Teaching Professional Skills to Engineering Students

ERIC Educational Resources Information Center

Goh, Suk Meng

2012-01-01

The objective of this study is to evaluate the potential of a game called "Star Power" to teach professional skills to mechanical engineering undergraduates. The game was conducted as an activity in a final year Professional Practice unit. A survey in the form of a questionnaire was administered to participating students in the following…

"Learning by Doing": A Teaching Method for Active Learning in Scientific Graduate Education

ERIC Educational Resources Information Center

Bot, Ludovic; Gossiaux, Pol-Bernard; Rauch, Carl-Philippe; Tabiou, Safouana

2005-01-01

This article describes an active learning method for the teaching of physical sciences and mathematics to engineers. After defining the challenges involved in the training of engineers, we shall describe the answers provided by our method, "learning by doing" (named "Apprentissage Par l"Action" in French), by introducing…

Development of Chemical Engineering Course Methods Using Action Research: Case Study

ERIC Educational Resources Information Center

Virkki-Hatakka, Terhi; Tuunila, Ritva; Nurkka, Niina

2013-01-01

This paper reports on the systematic development of a teaching methodology for two chemical engineering courses. The aim was to improve the quality of teaching to achieve expected learning outcomes more effectively. The development was carried out over a period of several years based on an action research methodology with data systematically…

Teaching "Community Engagement" in Engineering Education for International Development: Integration of an Interdisciplinary Social Work Curriculum

ERIC Educational Resources Information Center

Gilbert, Dorie J.; Held, Mary Lehman; Ellzey, Janet L.; Bailey, William T.; Young, Laurie B.

2015-01-01

This article reviews the literature on challenges faced by engineering faculty in educating their students on community-engaged, sustainable technical solutions in developing countries. We review a number of approaches to increasing teaching modules on social and community components of international development education, from adding capstone…

Information Technologies in Higher Education: Lessons Learned in Industrial Engineering

ERIC Educational Resources Information Center

Delgado-Almonte, Milagros; Andreu, Hernando Bustos; Pedraja-Rejas, Liliana

2010-01-01

This article describes a teaching experience in which information and communication technologies were applied in five industrial engineering courses at the Universidad de Tarapaca in Chile. The paper compares the performance and course pass rates of the e-learning platform and portable pocket PC platform with those of the same courses teaching in…

The Sound of Science

ERIC Educational Resources Information Center

Merwade, Venkatesh; Eichinger, David; Harriger, Bradley; Doherty, Erin; Habben, Ryan

2014-01-01

While the science of sound can be taught by explaining the concept of sound waves and vibrations, the authors of this article focused their efforts on creating a more engaging way to teach the science of sound--through engineering design. In this article they share the experience of teaching sound to third graders through an engineering challenge…

Science Educators Teaching Engineering Design: An Examination across Science Professional Development Sites

ERIC Educational Resources Information Center

Grubbs, Michael E.; Love, Tyler S.; Long, David E.; Kittrell, Danielle

2016-01-01

Although the currently employed STEM (science, technology, engineering, and mathematics) acronym is of recent origin, dating to the early 2000s (Chute, 2009), the United States has long emphasized the importance of teaching STEM in its public schools. Early efforts, such as "Science, the Endless Frontier" (Bush, 1945) and the…

The Teaching Challenge: Science, Engineering and the Knowledge Economy.

ERIC Educational Resources Information Center

Dowling, Patrick

2001-01-01

Presents the presidential address delivered to the Association for Science Education (ASE) at its annual meeting held at the University of Surrey, January 2001. Consists of three sections: (1) science and engineering and the knowledge economy; (2) teaching challenge and the role of science teachers; and (3) partnerships to support science,…

A Practical Teaching Course in Directed Protein Evolution Using the Green Fluorescent Protein as a Model

ERIC Educational Resources Information Center

Ruller, Roberto; Silva-Rocha, Rafael; Silva, Artur; Schneider, Maria Paula Cruz; Ward, Richard John

2011-01-01

Protein engineering is a powerful tool, which correlates protein structure with specific functions, both in applied biotechnology and in basic research. Here, we present a practical teaching course for engineering the green fluorescent protein (GFP) from "Aequorea victoria" by a random mutagenesis strategy using error-prone polymerase…

Teaching Engineering Statistics with Technology, Group Learning, Contextual Projects, Simulation Models and Student Presentations

ERIC Educational Resources Information Center

Romeu, Jorge Luis

2008-01-01

This article discusses our teaching approach in graduate level Engineering Statistics. It is based on the use of modern technology, learning groups, contextual projects, simulation models, and statistical and simulation software to entice student motivation. The use of technology to facilitate group projects and presentations, and to generate,…

How to teach artificial organs.

PubMed

Zapanta, Conrad M; Borovetz, Harvey S; Lysaght, Michael J; Manning, Keefe B

2011-01-01

Artificial organs education is often an overlooked field for many bioengineering and biomedical engineering students. The purpose of this article is to describe three different approaches to teaching artificial organs. This article can serve as a reference for those who wish to offer a similar course at their own institutions or incorporate these ideas into existing courses. Artificial organ classes typically fulfill several ABET (Accreditation Board for Engineering and Technology) criteria, including those specific to bioengineering and biomedical engineering programs.

Reverse engineering by design: using history to teach.

PubMed

Fagette, Paul

2013-01-01

Engineering students rarely have an opportunity to delve into the historic antecedents of design in their craft, and this is especially true for biomedical devices. The teaching emphasis is always on the new, the innovative, and the future. Even so, over the last decade, I have coupled a research agenda with engineering special projects into a successful format that allows young biomedical engineering students to understand aspects of their history and learn the complexities of design. There is value in having knowledge of historic engineering achievements, not just for an appreciation of these accomplishments but also for understanding exactly how engineers and clinicians of the day executed their feats-in other words, how the design process works. Ultimately, this particular educational odyssey confirms that history and engineering education are not only compatible but mutually supportive.

Integrating Engineering into Delaware's K-5 Classrooms: A Study of Pedagogical and Curricular Resources

NASA Astrophysics Data System (ADS)

Grusenmeyer, Linda Huey

This study examines the personal and curricular resources available to Delaware's elementary teachers during a time of innovative curriculum change, i.e., their knowledge, goals and beliefs regarding elementary engineering curriculum and the pedagogical support to teach two Science and Engineering Practices provided by science teaching materials. Delaware was at the forefront of K-12 STEM movement, first to adopt statewide elementary curriculum materials to complement existing science units, and one of the first to adopt the new science standards--Next Generation Science Standards. What supports were available to teachers as they adapted and adopted this new curriculum? To investigate this question, I examined (1) teachers' beliefs about engineering and the engineering curriculum, and (2) the pedagogical supports available to teachers in selected science and engineering curriculum. Teachers' knowledge, goals, and beliefs regarding Delaware's adoption of new elementary engineering curriculum were surveyed using an adapted version of the Design, Engineering, and Technology Survey (Hong, Purser, & Gardella, 2011; Yaser, Baker, Carpius, Krauss, & Roberts, 2006). Also, three open ended questions sought to reveal deeper understanding of teacher knowledge and understanding of engineering; their concerns about personal and systemic resources related to the new curriculum, its logistics, and feasibility; and their beliefs about the potential positive impact presented by the engineering education initiative. Teacher concerns were analyzed using the Concerns-Based Adoption Model (Hall & Hord, 2010). Lay understandings of engineering were analyzed by contrasting naive representations of engineering with three key characteristics of engineering adapted from an earlier study (Capobianco Diefes-Dux, Mena, & Weller, 2011). Survey findings for teachers who had attended training and those who have not yet attended professional development in the new curriculum were compared with few notable differences. Almost all elementary teacher respondents were familiar with engineering and able to define it using one or more key characteristics. They valued the inclusion of engineering in the elementary curriculum; however trained and untrained teachers reported they were not confident about teaching it and were unaware of the new standards related to engineering. Teachers saw potential advantages or benefits of the new curriculum as helping improve science and math understanding, an opportunity to increase vocational awareness, and engaging students and motivating them to learn. Most teachers saw similar barriers to implementation- lack of teacher knowledge, lack of time to learn about engineering and how to teach engineering, and lack of administrative support. Almost all were open to additional in-service training to learn more about this new curriculum. Three fifth grade science units were examined for evidence of teacher pedagogical support in teaching two Science and Engineering Practices (SEP) advocated by the Next Generation Science Standards. An analytic framework was developed based upon two NGSS SEPs: Asking questions, defining problems and Engaging in argument from evidence. Findings revealed that the kits varied greatly in their pedagogical approaches to the two SEPs and differences might be explained by each kit's underlying orientations to the teaching-learning process. Findings from these investigations have implications for the design of professional development and for engineering curricula. They highlight the importance of considering teacher beliefs about curriculum implementation and subject matter, as well as the importance of creating curriculum materials that focus teacher attention toward student thinking and the language rich science and engineering practices. Recommendations also include ongoing professional development to allow teachers time to try out and revise pedagogical routines that support the SEPs studied here.

Ethics education in the consulting engineering environment: where do we start?

PubMed

Elder, Keith E

2004-04-01

As a result of in-house discussions stimulated by previous Gonzaga engineering ethics conferences, Coffman Engineers began the implementation of what is to be a company-wide ethics training program. While preparing a curriculum aimed at consulting engineers, we found very little guidance as to how to proceed with most available literature being oriented towards the academic environment. We consulted a number of resources that address the teaching of engineering ethics in higher education, but questioned their applicability for the Consulting Engineering environment. This lack of guidance led us to informal research into the ethical knowledge and attitudes of both consulting engineers and engineering students. Some of our findings were unexpected, and suggest that a simpler approach to teaching ethics to working professionals might be preferred to that typically promoted in higher education.

Initiation of Research at the Aircraft Engine Research Laboratory

NASA Image and Video Library

1942-05-21

A group of National Advisory Committee for Aeronautics (NACA) officials and local dignitaries were on hand on May 8, 1942, to witness the Initiation of Research at the NACA's new Aircraft Engine Research Laboratory in Cleveland, Ohio. The group in this photograph was in the control room of the laboratory's first test facility, the Engine Propeller Research Building. The NACA press release that day noted, "First actual research activities in what is to be the largest aircraft engine research laboratory in the world was begun today at the National Advisory Committee for Aeronautics laboratory at the Cleveland Municipal Airport.” The ceremony, however, was largely symbolic since most of the laboratory was still under construction. Dr. George W. Lewis, the NACA's Director of Aeronautical Research, and John F. Victory, NACA Secretary, are at the controls in this photograph. Airport Manager John Berry, former City Manager William Hopkins, NACA Assistant Secretary Ed Chamberlain, Langley Engineer-in-Charge Henry Reid, Executive Engineer Carlton Kemper, and Construction Manager Raymond Sharp are also present. The propeller building contained two torque stands to test complete engines at ambient conditions. The facility was primarily used at the time to study engine lubrication and cooling systems for World War II aircraft, which were required to perform at higher altitudes and longer ranges than previous generations.

Planetary boundaries and environmental citizenship: enhancing environmental science through the Princeton University Science and Engineering Education Initiative

NASA Astrophysics Data System (ADS)

Riihimaki, C. A.; Caylor, K. K.; Wilcove, D. S.

2014-12-01

Introductory courses in environmental science are challenging to teach effectively because instructors need to balance the breadth of content coverage with the depth needed to solve complex, interdisciplinary environmental problems. For three years, the Council on Science and Technology at Princeton University has been collaborating with faculty to enhance the introductory environmental science course as part of the Science and Engineering Education Initiative, which aims to ensure that all students, regardless of discipline, graduate with an appreciation for and literacy in science and engineering. Our primary aim in the course is to foster improved environmental citizenship by helping students develop a mechanistic understanding of our individual, societal, and global role as agents of environmental change; an ability to predict or forecast the potential impact that decisions may have on the future structure and function of Earth systems; and a sense of responsibility that leads to informed action and decision-making related to environmental issues. Toward those ends, we have 1) reframed the course curriculum to focus on the central theme of "planetary boundaries" (Rockstrom et al., 2009), including their scientific evidence and policy implications, 2) developed hands-on laboratory exercises that give students authentic research experiences, and 3) modified the assessment to ensure that the students have consistent and clear indications of their mastery of the material. Student feedback through course surveys has been positive, although challenges remain, including coordination across a large teaching staff (two lead instructors for lecture and three TAs for discussion sections, plus a lead lab instructor and one lab TA), optimizing learning activities across the course structure (lecture, precept, and an optional lab), and engaging students that have diverse academic interests.

Active-Learning Laboratory Session to Teach the Four M's of Diabetes Care

PubMed Central

Plake, Kimberly S.; Nash, Christiane L.; Shepler, Brian M.

2009-01-01

Objective To implement an active-learning methodology for teaching diabetes care to pharmacy students and evaluate its effectiveness. Design Laboratory instruction was divided into 4 primary areas of diabetes care, referred to by the mnemonic, the 4 M's: meal planning, motion, medication, and monitoring. Students participated in skill-based learning laboratory stations and in simulated patient experiences. A pretest, retrospective pretest, and posttest were administered to measure improvements in students' knowledge about diabetes and confidence in providing care to diabetes patients. Assessment Students knowledge of and confidence in each area assessed improved. Students enjoyed the laboratory session and felt it contributed to their learning. Conclusion An active-learning approach to teaching diabetes care allowed students to experience aspects of the disease from the patient's perspective. This approach will be incorporated in other content areas. PMID:19513160

Teaching for quality learning in chemistry

NASA Astrophysics Data System (ADS)

Teixeira-Dias, José J. C.; Pedrosa de Jesus, Helena; Neri de Souza, Francislê; Watts, Mike

2005-09-01

In Portugal, the number of students in higher education increased from 80,000 in 1975 to 381,000 in 2000 (a change from 11% to 53% in the age group 18 22), meaning a major change in the diversity of student population with consequences well known and studied in other countries. The teaching of chemistry at the University of Aveiro, for the first-year students of science and engineering, has been subjected to continuous attention to implement quality and student-centred approaches. The work devoted to excellence and deep learning by several authors has been carefully followed and considered. This communication reports research work on chemistry teaching, associated with those developments for first-year students. The work included the design of strategies and the adoption of teaching and learning activities exploring ways to stimulate active learning by improving the quality of classroom interactions. In addition to regular lectures, large classes' teaching based on student-generated questions was explored. In order to improve students' motivation and stimulate their curiosity, conference-lectures were adopted to deal with selected topics of wide scientific, technological and social interest. Quantitative analysis and discussion of selected case studies, together with the organization of laboratory classes based on selected enquiry-based experiments, planned and executed by students, stimulated deep learning processes. A sample of 32 students was followed in the academic year of 2000/01 and the results obtained are here discussed in comparison with those of a sample of 100 students followed in 2001/02. Particular attention was paid to the quality of classroom interactions, the use of questions by students and their views about the course design.

Engineering education and a lifetime of learning

NASA Technical Reports Server (NTRS)

Eisley, J. (Editor)

1974-01-01

The result of an eleven-week study by the National Aeronautics and Space Administration (NASA) and the American Society of Engineering Education is presented. The study was the ninth of a series of programs. The purposes of the programs were: (1) to introduce engineering school faculty members to system design and to a particular approach to teaching system design, (2) to introduce engineering faculty to NASA and to a specific NASA center, and (3) to produce a study of use to NASA and to the participants. The story was concerned with engineering education in the U.S., and concentrated upon undergraduate education and teaching, although this bias was not meant to imply that research and graduate study are less important to engineering education.

Ronald N. Bracewell: An Appreciation

NASA Astrophysics Data System (ADS)

Thompson, A. Richard; Frater, Robert H.

2010-11-01

Ronald Newbold Bracewell (1921-2007) made fundamental contributions to the development of radio astronomy in the areas of interferometry, signal processing, and imaging, and also to tomography, various areas of data analysis, and the understanding of Fourier transforms. He was born in Sydney, Australia, and received a B.Sc. degree in mathematics and physics, and B.E. and M.E. degrees in electrical engineering from the University of Sydney, and his Ph.D. from the University of Cambridge, U.K., for research on the ionosphere. In 1949 he joined the Radiophysics Laboratory of CSIRO, where he became interested in radio astronomy. In 1955 he moved to Stanford University, California, where he became Lewis M. Terman Professor of Electrical Engineering. He retired from teaching in 1991, but continued to be active in radio astronomy and other applications of imaging techniques, etc. During his career he published ten books and more than 250 papers. Honors that he received include the Duddell Premium of the Institute of Electrical Engineers, London, the Hertz Medal of the IEEE, and the Order of Australia. For his work on imaging in tomography he was elected to Associate Membership of the Institute of Medicine of the U.S. National Academy of Sciences.

7. This photographic copy of an engineering drawing displays the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. This photographic copy of an engineering drawing displays the building's floor plan in its 1995 arrangement, with rooms designated. California Institute of Technology, Jet Propulsion Laboratory, Facilities Engineering and Construction Office, "Addition to Weigh & Control Bldg. E-35, Demolition, Floor and Roof Plans," drawing no. E35/3-0, October 5, 1983. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings of structures at JPL Edwards Facility. Drawings on file at JPL Plant Engineering, Pasadena, California. - Jet Propulsion Laboratory Edwards Facility, Weigh & Control Building, Edwards Air Force Base, Boron, Kern County, CA

4. This photographic copy of an engineering drawing shows the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. This photographic copy of an engineering drawing shows the plan and details for Test Stand "G" and the placement of the vibrator. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: "Vibration Test Facility-Bldg E-72, Floor & Roof Plans, Sections, Details & Door Schedule," drawing no. E72/2-5, 21 May 1964. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings of structures at JPL Edwards Facility. Drawings on file at JPL Plant Engineering, Pasadena, California. - Jet Propulsion Laboratory Edwards Facility, Test Stand G, Edwards Air Force Base, Boron, Kern County, CA

Educational Method of Engineering Ethics Aiming for Comprehensive Understanding

NASA Astrophysics Data System (ADS)

Yasui, Mitsukuni; Fujiki, Hiroyuki; Aoyagi, Manabu; Sugata, Noriyuki; Hayasaka, Narihito

We have proposed the omnibus style to teach an engineering ethics program. This paper showed the essentials to practice the class. The engineering ethics program is constituted with the factors; grade, subject, objective even if it is operated by some themes and teachers in the style of omnibus. Also, teachers have to select the cases which have dilemma of the engineer and the good effect. And they should teach how to analyze the case. Evaluation of student activity must be made up by versatile style according to objective. And student is recommended to understand the relation of activity and object.

Teaching Guidebook: An Introduction to Some Basics.

ERIC Educational Resources Information Center

Blake, Veronica M.; Dinham, Sarah M.

A teaching guide designed for use by new university teaching assistants provides help in preparing for and carrying out instructional responsibilities. Separate chapters give guidance with: preparing the course description and syllabus, including writing objectives; selecting teaching strategies (lecture, discussion, and laboratory experience);…

Annotated bibliography of software engineering laboratory literature

NASA Technical Reports Server (NTRS)

Kistler, David; Bristow, John; Smith, Don

1994-01-01

This document is an annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory. Nearly 200 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. This document has been updated and reorganized substantially since the original version (SEL-82-006, November 1982). All materials have been grouped into eight general subject areas for easy reference: (1) The Software Engineering Laboratory; (2) The Software Engineering Laboratory: Software Development Documents; (3) Software Tools; (4) Software Models; (5) Software Measurement; (6) Technology Evaluations; (7) Ada Technology; and (8) Data Collection. This document contains an index of these publications classified by individual author.

Technical Communications in Engineering and Science: The Practices within a Government Defense Laboratory.

ERIC Educational Resources Information Center

Von Seggern, Marilyn; Jourdain, Janet M.

1996-01-01

A survey of the different technical communications and information-related activities of 305 engineers and scientists from 3 sites of the Philips Laboratory, an Air Force research and development laboratory, found that scientists have a closer affinity for libraries and traditional information sources than do engineers. Eight tables depict survey…

E-Laboratory Design and Implementation for Enhanced Science, Technology and Engineering Education

ERIC Educational Resources Information Center

Morton, William; Uhomoibhi, James

2011-01-01

Purpose: This paper aims to report on the design and implementation of an e-laboratory for enhanced science, technology and engineering education studies. Design/methodology/approach: The paper assesses a computer-based e-laboratory, designed for new entrants to science, technology and engineering programmes of study in further and higher…

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 56: Technical Communications in Engineering and Science: The Practices Within a Government Defense Laboratory

NASA Technical Reports Server (NTRS)

VonSeggern, Marilyn; Jourdain, Janet M.; Pinelli, Thomas E.

1996-01-01

Research in recent decades has identified the varied information needs of engineers versus scientists. While most of that research looked at the differences among organizations, we surveyed engineers and scientists within a single Air Force research and development laboratory about their information gathering, usage, and production practices. The results of the Phillips Laboratory survey confirm prior assumptions about distinctions between engineering and science. Because military employees responded at a much higher rate than civilian staff, the survey also became an opportunity to profile a little-known segment of the engineer/scientist population. In addition to the effect Phillips Laboratory's stated mission may have on member engineers and scientists, other factors causing variations in technical communication and information-related activities are identified.

Teaching virtue: pedagogical implications of moral psychology.

PubMed

Frey, William J

2010-09-01

Moral exemplar studies of computer and engineering professionals have led ethics teachers to expand their pedagogical aims beyond moral reasoning to include the skills of moral expertise. This paper frames this expanded moral curriculum in a psychologically informed virtue ethics. Moral psychology provides a description of character distributed across personality traits, integration of moral value into the self system, and moral skill sets. All of these elements play out on the stage of a social surround called a moral ecology. Expanding the practical and professional curriculum to cover the skills and competencies of moral expertise converts the classroom into a laboratory where students practice moral expertise under the guidance of their teachers. The good news is that this expanded pedagogical approach can be realized without revolutionizing existing methods of teaching ethics. What is required, instead, is a redeployment of existing pedagogical tools such as cases, professional codes, decision-making frameworks, and ethics tests. This essay begins with a summary of virtue ethics and informs this with recent research in moral psychology. After identifying pedagogical means for teaching ethics, it shows how these can be redeployed to meet a broader, skills based agenda. Finally, short module profiles offer concrete examples of the shape this redeployed pedagogical agenda would take in the practical and professional ethics classroom.

Exploration and practice for engineering innovative talents training based on project-driven

NASA Astrophysics Data System (ADS)

Xu, Yishen; Lv, Qingsong; Ye, Yan; Wu, Maocheng; Gu, Jihua

2017-08-01

As one of the "excellent engineer education program" of the Ministry of Education and one of the characteristic majors of Jiangsu Province, the major of optoelectronic information science and engineering in Soochow University has a long history and distinctive features. In recent years, aiming to the talents training objective of "broad foundation, practiceoriented, to be creative", education and teaching reforms have been carried out, which emphasize basis of theoretical teaching, carrier of practical training, promotion of projects and discussion, and development of second class. By optimizing the teaching contents and course system of the theoretical courses, the engineering innovative talents training mode based on the project-driven has been implemented with playing a practical training carrier role and overall managing the second class teaching for cultivating students' innovative spirit and practical ability. Meanwhile, the evaluation mechanism of the students' comprehensive performance mainly based on "scores of theory test" is being gradually changed, and the activities such as scientific research, discipline competitions and social practices are playing an increasing important role in the students' comprehensive assessment. The produced achievements show that the proposed training model based on project-driven could stimulate the students' enthusiasm and initiative to participate in research activities and promote the training of students' ability of engineering practice and consciousness of innovation.

Innovation Online Teaching Module Plus Digital Engineering Kit with Proteus Software through Hybrid Learning Method to Improve Student Skills

NASA Astrophysics Data System (ADS)

Kholis, Nur; Syariffuddien Zuhrie, Muhamad; Rahmadian, Reza

2018-04-01

Demands the competence (competence) needs of the industry today is a competent workforce to the field of work. However, during this lecture material Digital Engineering (Especially Digital Electronics Basics and Digital Circuit Basics) is limited to the delivery of verbal form of lectures (classical method) is dominated by the Lecturer (Teacher Centered). Though the subject of Digital Engineering requires learning tools and is required understanding of electronic circuits, digital electronics and high logic circuits so that learners can apply in the world of work. One effort to make it happen is by creating an online teaching module and educational aids (Kit) with the help of Proteus software that can improve the skills of learners. This study aims to innovate online teaching modules plus kits in Proteus-assisted digital engineering courses through hybrid learning approaches to improve the skills of learners. The process of innovation is done by considering the skills and mastery of the technology of students (students) Department of Electrical Engineering - Faculty of Engineering – Universitas Negeri Surabaya to produce quality graduates Use of online module plus Proteus software assisted kit through hybrid learning approach. In general, aims to obtain adequate results with affordable cost of investment, user friendly, attractive and interactive (easily adapted to the development of Information and Communication Technology). With the right design, implementation and operation, both in the form of software both in the form of Online Teaching Module, offline teaching module, Kit (Educational Viewer), and e-learning learning content (both online and off line), the use of the three tools of the expenditure will be able to adjust the standard needs of Information and Communication Technology world, both nationally and internationally.

An Oil Spill in a Tube: An Accessible Approach for Teaching Environmental NMR Spectroscopy

ERIC Educational Resources Information Center

Simpson, Andre´ J.; Mitchell, Perry J.; Masoom, Hussain; Mobarhan, Yalda Liaghati; Adamo, Antonio; Dicks, Andrew P.

2015-01-01

NMR spectroscopy has great potential as an instrumental method for environmental chemistry research and monitoring but may be underused in teaching laboratories because of its complexity and the level of expertise required in operating the instrument and interpreting data. This laboratory experiment introduces environmental NMR spectroscopy to…

Utilizing a Rat Delayed Implantation Model to Teach Integrative Endocrinology and Reproductive Biology

ERIC Educational Resources Information Center

Geisert, Rodney D.; Smith, Michael F.; Schmelzle, Amanda L.; Green, Jonathan A.

2018-01-01

In this teaching laboratory, the students are directed in an exercise that involves designing and performing an experiment to determine estrogen's role in regulating delayed implantation (diapause) in female rats. To encourage active participation by the students, a discussion question is provided before the laboratory exercise in which each…

Virtual Laboratory as an Element of Visualization When Teaching Chemical Contents in Science Class

ERIC Educational Resources Information Center

Herga, Nataša Rizman; Grmek, Milena Ivanuš; Dinevski, Dejan

2014-01-01

Using a variety of visualization tools for teaching and learning science and chemistry is necessary because pupils better understand chemical phenomena and formulate appropriate mental models. The purpose of the presented study was to determine the importance of a virtual laboratory as a visualization element when addressing chemical contents…

Greenbeards in Yeast: An Undergraduate Laboratory Exercise to Teach the Genetics of Cooperation

ERIC Educational Resources Information Center

Ågren, J. Arvid; Williamson, Robert J.; Campitelli, Brandon E.; Wheeler, Jill

2017-01-01

Recent years have seen a dramatic increase in our understanding of the social behaviour of microbes. Here, we take advantage of these developments to present an undergraduate laboratory exercise that uses the cooperative flocculating behaviour of yeast ("Saccharomyces sp.") to introduce the concept of inclusive fitness and teach the…

Factors Contributing to the Development of Graduate Teaching Assistant Self-Image

ERIC Educational Resources Information Center

Sandi-Urena, Santiago; Gatlin, Todd

2013-01-01

Laboratory graduate teaching assistants (GTAs) play a prominent role in undergraduate chemistry education. Although the success of a laboratory program relies significantly on the performance of GTAs, only rarely have they been considered actual partners in instruction or have their experiences in the academic lab been investigated. This paper…

HANDBOOK, TEACHING SCIENCE TO EDUCATIONALLY DISADVANTAGED YOUTH.

ERIC Educational Resources Information Center

BINGHAM, N.E.; AND OTHERS

DESCRIBED ARE PROCEDURES AND LABORATORY MATERIALS WHICH ARE OUTGROWTHS OF A RESEARCH PROJECT OF THE SOUTHEASTERN EDUCATION LABORATORY FOR THE TEACHING OF SCIENCE TO DISADVANTAGED STUDENTS IN GRADES 7, 8, AND 9. PART 1 DEALS WITH THE CRITERIA USED IN DEVELOPING PROCEDURES AND MATERIALS FOR USE WITH EDUCATIONALLY DISADVANTAGED. INCLUDED ARE (1) THE…

Study of Visual and Auditory Presentation in Dental Lecture and Laboratory Instruction. Final Report.

ERIC Educational Resources Information Center

Allen, William H.; And Others

This study compared the relative effectiveness of an automated teaching machine with instructor presented instruction in graduate dental teaching. The objectives were to: (1) determine the effects of 3 laboratory instructional procedures used in combination with 2 lectures on the acquisition of manual operative skills, the learning of information…

Tapping Recent Alumni for the Development of Cutting-Edge, Investigative Teaching Laboratory Experiments

ERIC Educational Resources Information Center

Brodl, Mark R.

2005-01-01

This project presents a model for the development of an innovative, highly-experimental teaching laboratory course that centers upon collaborative efforts between recent alumni currently enrolled in Ph. D. programs (consultants) and current faculty. Because these consultants are involved in cutting-edge research, their combined talents represent a…

University of Illinois at Urbana-Champaign, Materials Research Laboratory progress report for FY 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-07-01

This interdisciplinary laboratory in the College of Engineering support research in areas of condensed matter physics, solid state chemistry, and materials science. These research programs are developed with the assistance of faculty, students, and research associates in the departments of Physics, Materials Science and Engineering, chemistry, Chemical Engineering, Electrical Engineering, Mechanical Engineering, and Nuclear Engineering.

Problem-based learning biotechnology courses in chemical engineering.

PubMed

Glatz, Charles E; Gonzalez, Ramon; Huba, Mary E; Mallapragada, Surya K; Narasimhan, Balaji; Reilly, Peter J; Saunders, Kevin P; Shanks, Jacqueline V

2006-01-01

We have developed a series of upper undergraduate/graduate lecture and laboratory courses on biotechnological topics to supplement existing biochemical engineering, bioseparations, and biomedical engineering lecture courses. The laboratory courses are based on problem-based learning techniques, featuring two- and three-person teams, journaling, and performance rubrics for guidance and assessment. Participants initially have found them to be difficult, since they had little experience with problem-based learning. To increase enrollment, we are combining the laboratory courses into 2-credit groupings and allowing students to substitute one of them for the second of our 2-credit chemical engineering unit operations laboratory courses.

The Foreign TA: A Guide to Teaching Effectiveness.

ERIC Educational Resources Information Center

Gburek, Janice L., Ed.; Dunnett, Stephen C., Ed.

Articles on teaching effectiveness for foreign teaching assistants (TAs) are presented. Topics include: adapting to the U.S. academic environment, understanding the role of the TA and gaining confidence, anticipating undergraduates' expectations, improving communication skills, and teaching laboratory classes and recitation classes. Titles and…

Teaching Assistant Policies and Procedures.

ERIC Educational Resources Information Center

Wisconsin Univ., Madison.

Policies and procedures covering graduate teaching assistants (TAs) at the University of Wisconsin-Madison are presented. A TA's duties may include classroom teaching under the direction of a faculty member, assisting in teaching classes, discussion groups, problem-solving sessions or laboratories, assisting in planning courses and developing…

Astronomy as a Tool for Training the Next Generation Technical Workforce

NASA Astrophysics Data System (ADS)

Romero, V.; Walsh, G.; Ryan, W.; Ryan, E.

A major challenge for today's institutes of higher learning is training the next generation of scientists, engineers, and optical specialists to be proficient in the latest technologies they will encounter when they enter the workforce. Although research facilities can offer excellent hands-on instructional opportunities, integrating such experiential learning into academic coursework without disrupting normal operations at such facilities can be difficult. Also, motivating entry level students to increase their skill levels by undertaking and successfully completing difficult coursework can require more creative instructional approaches, including fostering a fun, non-threatening environment for enhancing basic abilities. Astronomy is a universally appealing subject area, and can be very effective as a foundation for cultivating advanced competencies. We report on a project underway at the New Mexico Institute of Mining and Technology (NM Tech), a science and engineering school in Socorro, NM, to incorporate a state-of-the-art optical telescope and laboratory experiments into an entry-level course in basic engineering. Students enrolled in an explosive engineering course were given a topical problem in Planetary Astronomy: they were asked to develop a method to energetically mitigate a potentially hazardous impact between our planet and a Near-Earth asteroid to occur sometime in the future. They were first exposed to basic engineering training in the areas of fracture and material response to failure under different environmental conditions through lectures and traditional laboratory exercises. The students were then given access to NM Tech's Magdalena Ridge Observatory's (MRO) 2.4-meter telescope to collect physical characterization data, (specifically shape information) on two potentially hazardous asteroids (one roughly spherical, the other an elongated ellipsoid). Finally, the students used NM Tech's Energetic Materials Research and Testing Center (EMRTC) to perform field experiments to discern how an object's shape affects disruptive outcomes, and what must be factored into mitigation schemes to attain the desired result of complete destruction of the object. The scientific findings (details will be presented) derived by the students were valuable, and the students benefited from this non-traditional teaching approach such that they acquired a superior appreciation for research and experimentation, and exited the course with an increased motivation to continue their engineering training.

A Flipped Mode Teaching Approach for Large and Advanced Electrical Engineering Courses

ERIC Educational Resources Information Center

Ravishankar, Jayashri; Epps, Julien; Ambikairajah, Eliathamby

2018-01-01

A fully flipped mode teaching approach is challenging for students in advanced engineering courses, because of demanding pre-class preparation load, due to the complex and analytical nature of the topics. When this is applied to large classes, it brings an additional complexity in terms of promoting the intended active learning. This paper…

Teaching Engineering/Engineering Teaching: Interdisciplinary Collaboration and the Construction of Academic Identities

ERIC Educational Resources Information Center

Winberg, Christine

2008-01-01

Academics in higher education institutions are members of disciplinary communities by virtue of their qualifications and research activities, and as teachers of particular disciplines (or professions) they are (or need to become) members of a community of educational practitioners. In this paper, I analyse the ways in which a small group of…

Breaking Ground: Improving Undergraduate Engineering Projects through Flipped Teaching of Literature Search Techniques

ERIC Educational Resources Information Center

Maddison, Tasha; Beneteau, Donna; Sokoloski, Brandy

2014-01-01

This case study describes the use of flipped teaching for information literacy instruction in a new course, "Drill, Blast, and Excavate GeoE 498," within the mining option for geological engineering (GeoE) students. These students will enter the mining industry with less discipline-specific knowledge than a student that graduated with a…

Project-Based Curriculum for Teaching Analytical Design to Freshman Engineering Students via Reconfigurable Trebuchets

ERIC Educational Resources Information Center

Herber, Daniel R.; Deshmukh, Anand P.; Mitchell, Marlon E.; Allison, James T.

2016-01-01

This paper presents an effort to revitalize a large introductory engineering course for incoming freshman students that teaches them analytical design through a project-based curriculum. This course was completely transformed from a seminar-based to a project-based course that integrates hands-on experimentation with analytical work. The project…

From Rhetoric to Reality: Case Studies of Two Fifth Grade Science Teachers to Inform Reform

ERIC Educational Resources Information Center

Maynard, Kathie Jo

2013-01-01

The purpose of this qualitative study was to explore two elementary teachers' implementation of engineering design over two academic years and to describe how their teaching practice changed over the two instructional cycles. This study used field notes and audio transcripts of the teachers during their engineering design teaching, written…

Aspects on Teaching/Learning with Object Oriented Programming for Entry Level Courses of Engineering.

ERIC Educational Resources Information Center

de Oliveira, Clara Amelia; Conte, Marcos Fernando; Riso, Bernardo Goncalves

This work presents a proposal for Teaching/Learning, on Object Oriented Programming for Entry Level Courses of Engineering and Computer Science, on University. The philosophy of Object Oriented Programming comes as a new pattern of solution for problems, where flexibility and reusability appears over the simple data structure and sequential…

Improving Science Scores of Middle School Students with Learning Disabilities through Engineering Problem Solving Activities

ERIC Educational Resources Information Center

Starling, A. Leyf Peirce; Lo, Ya-Yu; Rivera, Christopher J.

2015-01-01

This study evaluated the differential effects of three different science teaching methods, namely engineering teaching kit (ETK), explicit instruction (EI), and a combination of the two methods (ETK+EI), in two sixth-grade science classrooms. Twelve students with learning disabilities (LD) and/or attention deficit hyperactivity disorder (ADHD)…

Early Childhood Teachers' Beliefs about Readiness for Teaching Science, Technology, Engineering, and Mathematics

ERIC Educational Resources Information Center

Park, Mi-Hwa; Dimitrov, Dimiter M.; Patterson, Lynn G.; Park, Do-Yong

2017-01-01

The purpose of this study was to examine beliefs of early childhood teachers about their readiness for teaching science, technology, engineering, and mathematics, with a focus on testing for heterogeneity of such beliefs and differential effects of teacher-related factors. The results from latent class analysis of survey data revealed two latent…

A Simple Experiment for Teaching Process Intensification by Static Mixing in Chemical Reaction Engineering

ERIC Educational Resources Information Center

Baz-Rodríguez, Sergio; Herrera-Soberanis, Natali; Rodríguez-Novelo, Miguel; Guillén-Francisc, Juana; Rocha-Uribe, José

2016-01-01

An experiment for teaching mixing intensification in reaction engineering is described. For this, a simple tubular reactor was constructed; helical static mixer elements were fabricated from stainless steel strips and inserted into the reactor. With and without the internals, the equipment operates as a static mixer reactor or a laminar flow…

Implementing "Big Ideas" to Advance the Teaching and Learning of Science, Technology, Engineering, and Mathematics (STEM)

ERIC Educational Resources Information Center

Chalmers, Christina; Carter, Merilyn; Cooper, Tom; Nason, Rod

2017-01-01

Although education experts are increasingly advocating the incorporation of integrated Science, Technology, Engineering, and Mathematics (STEM) curriculum units to address limitations in much current STEM teaching and learning, a review of the literature reveals that more often than not such curriculum units are not mediating the construction of…

Perspectives on Failure in the Classroom by Elementary Teachers New to Teaching Engineering

ERIC Educational Resources Information Center

Lottero-Perdue, Pamela S.; Parry, Elizabeth A.

2017-01-01

This mixed methods study examines perspectives on failure in the classroom by elementary teachers new to teaching engineering. The study participants included 254 teachers in third, fourth, and fifth grade who responded to survey questions about failure, as well as a subset of 38 of those teachers who participated in interviews about failure. The…

Intelligent Performance Assessment of Students' Laboratory Work in a Virtual Electronic Laboratory Environment

ERIC Educational Resources Information Center

Achumba, I. E.; Azzi, D.; Dunn, V. L.; Chukwudebe, G. A.

2013-01-01

Laboratory work is critical in undergraduate engineering courses. It is used to integrate theory and practice. This demands that laboratory activities are synchronized with lectures to maximize their derivable learning outcomes, which are measurable through assessment. The typical high costs of the traditional engineering laboratory, which often…

Engineering Encounters: Engineering Adaptations

ERIC Educational Resources Information Center

Gatling, Anne; Vaughn, Meredith Houle

2015-01-01

Engineering is not a subject that has historically been taught in elementary schools, but with the emphasis on engineering in the "Next Generation Science Standards," curricula are being developed to explicitly teach engineering content and design. However, many of the scientific investigations already conducted with students have…

Applying ``intelligent`` materials for materials education: The Labless Lab{trademark}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrade, J.D.; Scheer, R.

1994-12-31

A very large number of science and engineering courses taught in colleges and universities today do not involve laboratories. Although good instructors incorporate class demonstrations, hands on homework, and various teaching aids, including computer simulations, the fact is that students in such courses often accept key concepts and experimental results without discovering them for themselves. The only partial solution to this problem has been increasing use of class demonstrations and computer simulations. The authors feel strongly that many complex concepts can be observed and assimilated through experimentation with properly designed materials. They propose the development of materials and specimens designedmore » specifically for education purposes. Intelligent and communicative materials are ideal for this purpose. Specimens which respond in an observable fashion to new environments and situations provided by the students/experimenter provide a far more effective materials science and engineering experience than readouts and data generated by complex and expensive machines, particularly in an introductory course. Modern materials can be designed to literally communicate with the observer. The authors embarked on a project to develop a series of Labless Labs{trademark} utilizing various degrees and levels of intelligence in materials. It is expected that such Labless Labs{trademark} would be complementary to textbooks and computer simulations and to be used to provide a reality for students in courses and other learning situations where access to a laboratory is non-existent or limited.« less

Physics Education Research at the Upper Division at the University of Maine

NASA Astrophysics Data System (ADS)

Thompson, John

2013-04-01

Researchers from the University of Maine Physics Education Research Laboratory are conducting several investigations of the learning and teaching of physics beyond the introductory level. Content topics include intermediate mechanics, electronics, thermodynamics and statistical mechanics. One focus of our work is the identification and addressing of specific student difficulties with topics such as damped harmonic motion, bipolar junction transistor (BJT) circuits, work, entropy, and the Boltzmann factor. Student understanding and use of the underlying mathematics has been one important emerging theme, including definite integrals, partial derivatives, and linear differential equations. Recent work in mechanics has focused on understanding the interplay of mathematical and physical reasoning when describing damped harmonic motion, including framing and representational issues. In electronics, there has been an ongoing investigation of student understanding of the behavior of basic BJT follower and amplifier circuits as well as related issues of signal and bias. In thermal physics, student understanding of state functions, heat engines and the Carnot cycle, the First and Second Laws of thermodynamics, and the macroscopic and microscopic perspectives on entropy have been investigated. The greater content sophistication in these courses has drawn attention to the specific needs, constraints, and advantages of instructional materials tailored to the upper division. Future directions include more attention to interdisciplinary topics across mathematics, physics, and engineering in particular, as well as metacognition in the laboratory.

Knowledge, attitude and practice of aspects of laboratory safety in Pathology Laboratories at the University of Port Harcourt Teaching Hospital, Nigeria.

PubMed

Ejilemele, A A; Ojule, A C

2005-12-01

To assess current knowledge, attitudes and practice of aspects of laboratory safety in pathology laboratories at the University of Port Harcourt Teaching Hospital in view of perceived inadequacies in safety practices in clinical laboratories in developing countries. Sixty (60) self- administered questionnaires were distributed to all cadres of staff in four (4) different laboratories (Chemical Pathology, Haematology, Blood bank and Medical Microbiology) at the Hospital. Gross deficiencies were found in the knowledge, attitudes and practice of laboratory safety by laboratory staff in areas of use of personal protective equipment, specimen collection and processing, centrifuge--related hazards, infective hazards waste disposal and provision and use of First Aid Kits. Issues pertaining to laboratory safety are not yet given adequate attention by both employers and employees in developing countries in this ear of resurgence of diseases such as HIV/AIDS and Hepatitis Band C, is emphasized.

32 CFR 555.2 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... FOR OTHERS § 555.2 Applicability. This regulation applies to the U.S. Army Engineer Waterways Experiment Station (WES), the U.S. Army Construction Engineering Research Laboratory (CERL), the U.S. Army Engineer Topographic Laboratories (ETL), the U.S. Army Coastal Engineering Research Center (CERC), the U.S...

32 CFR 555.2 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... FOR OTHERS § 555.2 Applicability. This regulation applies to the U.S. Army Engineer Waterways Experiment Station (WES), the U.S. Army Construction Engineering Research Laboratory (CERL), the U.S. Army Engineer Topographic Laboratories (ETL), the U.S. Army Coastal Engineering Research Center (CERC), the U.S...

32 CFR 555.2 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... FOR OTHERS § 555.2 Applicability. This regulation applies to the U.S. Army Engineer Waterways Experiment Station (WES), the U.S. Army Construction Engineering Research Laboratory (CERL), the U.S. Army Engineer Topographic Laboratories (ETL), the U.S. Army Coastal Engineering Research Center (CERC), the U.S...

32 CFR 555.2 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... FOR OTHERS § 555.2 Applicability. This regulation applies to the U.S. Army Engineer Waterways Experiment Station (WES), the U.S. Army Construction Engineering Research Laboratory (CERL), the U.S. Army Engineer Topographic Laboratories (ETL), the U.S. Army Coastal Engineering Research Center (CERC), the U.S...

Mathematics and its value for engineering students: what are the implications for teaching?

NASA Astrophysics Data System (ADS)

Harris, Diane; Black, Laura; Hernandez-Martinez, Paul; Pepin, Birgit; Williams, Julian; with the TransMaths Team

2015-04-01

Mathematics has long been known to be problematic for university engineering students and their teachers, for example, Scanlan.[1] This paper presents recent data gathered from interviews with engineering students who experienced problems with mathematics and their lecturers during their transition through the first year in different programme contexts. Our interviews with the students reveal how they understand the relation between engineering and mathematics and we draw on the concept of 'use- and exchange-value' to explore this relationship more fully. This paper challenges both the pedagogical practice of teaching non-contextualized mathematics and the lack of transparency regarding the significance of mathematics to engineering. We conclude that the value of mathematics in engineering remains a central problem, and argue that mathematics should be a fundamental concern in the design and practice of first-year engineering.

Virtual Visualisation Laboratory for Science and Mathematics Content (Vlab-SMC) with Special Reference to Teaching and Learning of Chemistry

NASA Astrophysics Data System (ADS)

Badioze Zaman, Halimah; Bakar, Norashiken; Ahmad, Azlina; Sulaiman, Riza; Arshad, Haslina; Mohd. Yatim, Nor Faezah

Research on the teaching of science and mathematics in schools and universities have shown that available teaching models are not effective in instilling the understanding of scientific and mathematics concepts, and the right scientific and mathematics skills required for learners to become good future scientists (mathematicians included). The extensive development of new technologies has a marked influence on education, by facilitating the design of new learning and teaching materials, that can improve the attitude of learners towards Science and Mathematics and the plausibility of advanced interactive, personalised learning process. The usefulness of the computer in Science and Mathematics education; as an interactive communication medium that permits access to all types of information (texts, images, different types of data such as sound, graphics and perhaps haptics like smell and touch); as an instrument for problem solving through simulations of scientific and mathematics phenomenon and experiments; as well as measuring and monitoring scientific laboratory experiments. This paper will highlight on the design and development of the virtual Visualisation Laboratory for Science & Mathematics Content (VLab-SMC) based on the Cognitivist- Constructivist-Contextual development life cycle model as well as the Instructional Design (ID) model, in order to achieve its objectives in teaching and learning. However, this paper with only highlight one of the virtual labs within VLab-SMC that is, the Virtual Lab for teaching Chemistry (VLab- Chem). The development life cycle involves the educational media to be used, measurement of content, and the authoring and programming involved; whilst the ID model involves the application of the cognitivist, constructivist and contextual theories in the modeling of the modules of VLab-SMC generally and Vlab-Chem specifically, using concepts such as 'learning by doing', contextual learning, experimental simulations 3D and real-time animations to create a virtual laboratory based on a real laboratory. Initial preliminary study shows positive indicators of VLab-Chem for the teaching and learning of Chemistry on the topic of 'Salts and Acids'.

Lecturers' Experiences of Teaching STEM to Students with Disabilities

ERIC Educational Resources Information Center

Ngubane-Mokiwa, S. A.; Khoza, S. B.

2016-01-01

Innovative teaching is a concept based on student-centred teaching strategies. Access to Science, Technology, Engineering and Mathematics (STEM) subjects has not been equitable due to use of traditional teaching strategies. These strategies tend to exclude students with disabilities who can effectively learn in environments that appropriately and…

Creative Teaching in STEM

ERIC Educational Resources Information Center

Pollard, Vikki; Hains-Wesson, Rachael; Young, Karen

2018-01-01

If Science, Technology, Engineering and Mathematics (STEM) disciplines in higher education are to retain students, there needs to be a shift towards teaching in more enriching and interesting ways. Creative teaching needs to become more prominent in STEM. This article presents a study that defines creative teaching in the STEM context and…

Research Skills and Ethics--A Graduate Course Empowering Graduate Students for Productive Research Careers in Graduate School and Beyond

NASA Astrophysics Data System (ADS)

Mabrouk, Patricia Ann

2001-12-01

This paper describes a course for first-year graduate students that teaches the fundamental so-called "soft skills" required for success in graduate school and beyond. Topics covered are ethics, laboratory safety and waste management, chemical information retrieval and literacy, experimental design, scientific record keeping, statistics, career development, and communications, including technical writing and oral presentation. Whenever possible students are put in direct contact with local technical experts and available resources. The course, well regarded by both students and faculty, has now been taught at Northeastern University for five years in the summer academic quarter to graduate students in chemistry and related departments (pharmacy and chemical engineering) who have successfully completed their first-year course work.

Teaching communication skills to hospice teams: comparing the effectiveness of a communication skills laboratory with in-person, second life, and phone role-playing.

PubMed

Hamilton, Gillian; Ortega, Rosio; Hochstetler, Vicki; Pierson, Kristen; Lin, Peiyi; Lowes, Susan

2014-09-01

Communication skills are critical in hospice care but challenging to teach. Therefore, a hospice agency developed a communication skills laboratory for nurses and social workers. Learners role-played 3 common hospice scenarios. The role-play modalities were in-person, Second Life, and telephone. Learners were scored on 4 communication aspects. Learners in all modalities rated the laboratory as very effective. However, learners in the Second Life and phone modality showed greater improvements from scene 1 to 3 than those in the in-person modality. There were no significant differences in improvement between the Second Life and phone modalities. Results support the effectiveness of this communication skills laboratory while using different teaching modalities and show phone and Second Life role-plays were more effective than an in-person role-play. © The Author(s) 2013.

This photocopy of an engineering drawing shows the BakerPerkins 150gallon ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

This photocopy of an engineering drawing shows the Baker-Perkins 150-gallon mixer installation in the building. Austin, Field & Fry, Architects Engineers, 22311 West Third Street, Los Angeles 57, California: Edwards Test Station Complex, Jet Propulsion Laboratory, California Institute of Technology, Edwards Air Force Base, Edwards, California: "150 Gallon Mixer System Bldg. E-34, Plans, Sections & Details," drawing no. E34/6-0, 10 July 1963. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings of structures at JPL Edwards Facility. Drawings on file at JPL Plant Engineering, Pasadena, California - Jet Propulsion Laboratory Edwards Facility, Mixer, Edwards Air Force Base, Boron, Kern County, CA

This photographic copy of an engineering drawing shows floor plans, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

This photographic copy of an engineering drawing shows floor plans, sections and elevations of Building E-86, with details typical of the steel frame and "Transite" building construction at JPL Edwards Facility. California Institute of Technology, Jet Propulsion Laboratory, Facilities Engineering and Construction Office: "Casting & Curing, Building E-86, Floor Plan, Elevations & Section," drawing no. E86/6, 25 February 1977. California Institute of Technology, Jet Propulsion Laboratory, Plant Engineering: engineering drawings of structures at JPL Edwards Facility. Drawings on file at JPL Plant Engineering, Pasadena, California - Jet Propulsion Laboratory Edwards Facility, Casting & Curing Building, Edwards Air Force Base, Boron, Kern County, CA

Reactor physics teaching and research in the Swiss nuclear engineering master

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chawla, R.; Paul Scherrer Inst., CH-5232 Villigen PSI

Since 2008, a Master of Science program in Nuclear Engineering (NE) has been running in Switzerland, thanks to the combined efforts of the country's key players in nuclear teaching and research, viz. the Swiss Federal Inst.s of Technology at Lausanne (EPFL) and at Zurich (ETHZ), the Paul Scherrer Inst. (PSI) at Villigen and the Swiss Nuclear Utilities (Swissnuclear). The present paper, while outlining the academic program as a whole, lays emphasis on the reactor physics teaching and research training accorded to the students in the framework of the developed curriculum. (authors)

A woman like you: Women scientists and engineers at Brookhaven National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benkovitz, Carmen; Bernholc, Nicole; Cohen, Anita

1991-01-01

This publication by the women in Science and Engineering introduces career possibilities in science and engineering. It introduces what work and home life are like for women who have already entered these fields. Women at Brookhaven National Laboratory work in a variety of challenging research roles -- from biologist and environmental scientist to safety engineer, from patent lawyer to technician. Brookhaven National Laboratory is a multi-program laboratory which carries out basic and applied research in the physical, biomedical and environmental sciences and in selected energy technologies. The Laboratory is managed by Associated University, Inc., under contract with the US Departmentmore » of Energy. Brookhaven and the other national laboratories, because of their enormous research resources, can play a critical role in a education and training of the workforce.« less

A woman like you: Women scientists and engineers at Brookhaven National Laboratory. Careers in action

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-12-31

This publication by the women in Science and Engineering introduces career possibilities in science and engineering. It introduces what work and home life are like for women who have already entered these fields. Women at Brookhaven National Laboratory work in a variety of challenging research roles -- from biologist and environmental scientist to safety engineer, from patent lawyer to technician. Brookhaven National Laboratory is a multi-program laboratory which carries out basic and applied research in the physical, biomedical and environmental sciences and in selected energy technologies. The Laboratory is managed by Associated University, Inc., under contract with the US Departmentmore » of Energy. Brookhaven and the other national laboratories, because of their enormous research resources, can play a critical role in a education and training of the workforce.« less

Hands-on curriculum teaches biomedical engineering concepts to home-schooled students.

PubMed

Sagstetter, Ann M; Nimunkar, Amit J; Tompkins, Willis J

2009-01-01

University level outreach has increased over the last decade to stimulate K-12 student interest in engineering related fields. Home schooling students are one of the groups that are valued for engineering admissions due to diligent study habits and high achievement scores. However, home schooled students have inadequate access to science, math, and engineering related resources, which precludes the development of interdisciplinary teaching methods. To address this problem, we have developed a hands-on, STEM based curriculum as a safe and comprehensive supplement to current home schooling curricula. The ultimate goal is to stimulate university-student relations and subsequently increase engineering recruitment opportunities. Our pre and post workshop survey comparisons demonstrate that integrating disciplines, via the manner presented in this study, provides a K-12 student-friendly engineering learning method.

Forming engineers' sociocultural competence: Engineering ethics at tomsk polytechnic university

NASA Astrophysics Data System (ADS)

Galanina, E.; Dulzon, A.; Schwab, A.

2015-10-01

The aim of the present research is to discuss Tomsk Polytechnic University in respect of forming engineers’ sociocultural competence and teaching engineering ethics. Today international standards of training engineers cover efficient communication skills, ability to understand societal and environment context, professional and ethical responsibility. This article deals with the problem of contradiction between the need to form engineers’ sociocultural competence in Russian higher education institutions in order to meet the requirements of international accreditation organizations and the real capabilities of existing engineering curricula. We have described ethics teaching experience of TPU, studied the engineering master programs of TPU to see how the planned results are achieved. We have also given our recommendations to alter the structure of TPU educational curricula, which can also be applied in other higher education institutions.

Considerations on Educating Engineers in Sustainability

ERIC Educational Resources Information Center

Boyle, Carol

2004-01-01

The teaching of sustainability to engineers will follow similar paths to that of environmental engineering. There is a strong feeling that environmental engineering is a discipline unto itself, requiring knowledge of chemistry, physics, biology, hydrology, toxicology, modelling and law. However, environmental engineering can also be encompassed…