Origami Wheel Transformer: A Variable-Diameter Wheel Drive Robot Using an Origami Structure.

PubMed

Lee, Dae-Young; Kim, Sa-Reum; Kim, Ji-Suk; Park, Jae-Jun; Cho, Kyu-Jin

2017-06-01

A wheel drive mechanism is simple, stable, and efficient, but its mobility in unstructured terrain is seriously limited. Using a deformable wheel is one of the ways to increase the mobility of a wheel drive robot. By changing the radius of its wheels, the robot becomes able to pass over not only high steps but also narrow gaps. In this article, we propose a novel design for a variable-diameter wheel using an origami-based soft robotics design approach. By simply folding a patterned sheet into a wheel shape, a variable-diameter wheel was built without requiring lots of mechanical parts and a complex assembly process. The wheel's diameter can change from 30 to 68 mm, and it is light in weight at about 9.7 g. Although composed of soft materials (fabrics and films), the wheel can bear more than 400 times its weight. The robot was able to change the wheel's radius in response to terrain conditions, allowing it to pass over a 50-mm gap when the wheel is shrunk and a 50-mm step when the wheel is enlarged.

Factors affecting minimum push and pull forces of manual carts.

PubMed

Al-Eisawi, K W; Kerk, C J; Congleton, J J; Amendola, A A; Jenkins, O C; Gaines, W

1999-06-01

The minimum forces needed to manually push or pull a 4-wheel cart of differing weights with similar wheel sizes from a stationary state were measured on four floor materials under different conditions of wheel width, diameter, and orientation. Cart load was increased from 0 to 181.4 kg in increments of 36.3 kg. The floor materials were smooth concrete, tile, asphalt, and industrial carpet. Two wheel widths were tested: 25 and 38 mm. Wheel diameters were 51, 102, and 153 mm. Wheel orientation was tested at four levels: F0R0 (all four wheels aligned in the forward direction), F0R90 (the two front wheels, the wheels furthest from the cart handle, aligned in the forward direction and the two rear wheels, the wheels closest to the cart handle, aligned at 90 degrees to the forward direction), F90R0 (the two front wheels aligned at 90 degrees to the forward direction and the two rear wheels aligned in the forward direction), and F90R90 (all four wheels aligned at 90 degrees to the forward direction). Wheel width did not have a significant effect on the minimum push/pull forces. The minimum push/pull forces were linearly proportional to cart weight, and inversely proportional to wheel diameter. The coefficients of rolling friction were estimated as 2.2, 2.4, 3.3, and 4.5 mm for hard rubber wheels rolling on smooth concrete, tile, asphalt, and industrial carpet floors, respectively. The effect of wheel orientation was not consistent over the tested conditions, but, in general, the smallest minimum push/pull forces were measured with all four wheels aligned in the forward direction, whereas the largest minimum push/pull forces were measured when all four wheels were aligned at 90 degrees to the forward direction. There was no significant difference between the push and pull forces when all four wheels were aligned in the forward direction.

Bulk Enthalpy Calculations in the Arc Jet Facility at NASA ARC

NASA Technical Reports Server (NTRS)

Thompson, Corinna S.; Prabhu, Dinesh; Terrazas-Salinas, Imelda; Mach, Jeffrey J.

2011-01-01

The Arc Jet Facilities at NASA Ames Research Center generate test streams with enthalpies ranging from 5 MJ/kg to 25 MJ/kg. The present work describes a rigorous method, based on equilibrium thermodynamics, for calculating the bulk enthalpy of the flow produced in two of these facilities. The motivation for this work is to determine a dimensionally-correct formula for calculating the bulk enthalpy that is at least as accurate as the conventional formulas that are currently used. Unlike previous methods, the new method accounts for the amount of argon that is present in the flow. Comparisons are made with bulk enthalpies computed from an energy balance method. An analysis of primary facility operating parameters and their associated uncertainties is presented in order to further validate the enthalpy calculations reported herein.

Art on Wheels.

ERIC Educational Resources Information Center

Szekely, George

2002-01-01

Discusses the use of wheels in children's art. Focuses on collecting wheels, ideas for decorating different artworks with wheels, and objects that can move on wheels. Sees wheels as an inspiration for children's art, reflecting on the use of this object in the art classroom. (CMK)

A Study on Wheel Sinkage and Rolling Resistance with variations in wheel geometry for Plain and Lugged wheels on TRI -1 Soil Simulant

NASA Astrophysics Data System (ADS)

Gireesh Kumar, Pala; Jayalekshmi, S.

2018-03-01

Wheel-soil Interaction studies are gaining momentum in the field of Terramechanics, but the basis is Terzaghi’s bearing capacity equation. For the current study, on a lunar soil simulant TRI – 1, two plain rigid wheels are considered, i.e., small wheel (dia. of 210 mm and width of 50 mm) and large wheel (dia. 160 mm and width 32 mm). Also, different number of lugs (N = 8, 12, 16) with various lug heights (h = 5 mm, 10 mm, 15 mm) are used. In this paper, the variation of wheel sinkages from experiments obtained for various wheel weights are examined and presented. The parameter, Coefficient of rolling resistance (CRR) is determined for various cases. Hence, rolling resistance was determined and examined from the obtained CRR for all cases. Among the cases examined, the large wheel with weight 67.44 N for plain wheels and weight 67.85 N for lugged wheel (no. of lugs = 16, and height of lugs = 5 mm) registered better mobility. Similarly, for small wheel with weight 52.189 N for plain wheel and weight 52.481 N for lugged wheel (no. of lugs = 16, and height of lugs = 5 mm) registered better mobility, a lesser rolling resistance for these cases.

Miniature pipe crawler tractor

DOEpatents

McKay, Mark D.; Anderson, Matthew O.; Ferrante, Todd A.; Willis, W. David

2000-01-01

A pipe crawler tractor may comprise a half tractor assembly having a first base drive wheel, a second base drive wheel, and a top drive wheel. The drive wheels are mounted in spaced-apart relation so that the top drive wheel is positioned between the first and second base drive wheels. The mounting arrangement is also such that the first and second base drive wheels contact the inside surface of the pipe at respective first and second positions and so that the top drive wheel contacts the inside surface of the pipe at a third position, the third position being substantially diametrically opposed to the first and second positions. A control system connected to the half tractor assembly controls the rotation of the first base wheel, the second base wheel, and the top drive wheel to move the half tractor assembly within the pipe.

Reduction of extinction and reinstatement of cocaine seeking by wheel running in female rats.

PubMed

Zlebnik, Natalie E; Anker, Justin J; Gliddon, Luke A; Carroll, Marilyn E

2010-03-01

Previous work has shown that wheel running reduced the maintenance of cocaine self-administration in rats. In the present study, the effect of wheel running on extinction and reinstatement of cocaine seeking was examined. Female rats were trained to run in a wheel during 6-h sessions, and they were then catheterized and placed in an operant conditioning chamber where they did not have access to the wheel but were allowed to self-administer iv cocaine. Subsequently, rats were divided into four groups and were tested on the extinction and reinstatement of cocaine seeking while they had varying access to a wheel in an adjoining compartment. The four groups were assigned to the following wheel access conditions: (1) wheel running during extinction and reinstatement (WER), (2) wheel running during extinction and a locked wheel during reinstatement (WE), (3) locked wheel during extinction and wheel running during reinstatement (WR), and (4) locked wheel during extinction and reinstatement (WL). WE and WR were retested later to examine the effect of one session of wheel access on cocaine-primed reinstatement. There were no group differences in wheel revolutions, in rate of acquisition of cocaine self-administration, or in responding during maintenance when there was no wheel access. However, during extinction, WE and WER responded less than WR and WL. WR and WER had lower cocaine-primed reinstatement than WE and WL. One session of wheel exposure in WE also suppressed cocaine-primed reinstatement. Wheel running immediately and effectively reduced cocaine-seeking behavior, but concurrent access to running was necessary. Thus, exercise is a useful and self-sustaining intervention to reduce cocaine-seeking behavior.

Phase Transition Enthalpy Measurements of Organic and Organometallic Compounds. Sublimation, Vaporization and Fusion Enthalpies From 1880 to 2015. Part 1. C1 - C10

NASA Astrophysics Data System (ADS)

Acree, William; Chickos, James S.

2016-09-01

A compendium of phase change enthalpies published in 2010 is updated to include the period 1880-2015. Phase change enthalpies including fusion, vaporization, and sublimation enthalpies are included for organic, organometallic, and a few inorganic compounds. Part 1 of this compendium includes organic compounds from C1 to C10. Part 2 of this compendium, to be published separately, will include organic and organometallic compounds from C11 to C192. Sufficient data are presently available to permit thermodynamic cycles to be constructed as an independent means of evaluating the reliability of the data. Temperature adjustments of phase change enthalpies from the temperature of measurement to the standard reference temperature, T = 298.15 K, and a protocol for doing so are briefly discussed.

An examination of the thermodynamics of fusion, vaporization, and sublimation of ibuprofen and naproxen by correlation gas chromatography.

PubMed

Maxwell, Rachel; Chickos, James

2012-02-01

The vaporization enthalpies of (S)-ibuprofen and (S)-naproxen measured by correlation gas chromatography at T = 298.15 K are reported and compared with literature values. Adjustment of the fusion enthalpies of (RS)- and (S)-ibuprofen and (S)-naproxen to T = 298.15 K and combined with the vaporization enthalpy of the (S)-enantiomer of both ibuprofen and naproxen also at T = 298.15 K resulted in the sublimation enthalpies of both (S)-enantiomers. On the assumption that the vaporization enthalpy of the racemic form of ibuprofen is within the experimental uncertainty of the chiral form, the sublimation enthalpy of racemic ibuprofen was also evaluated. The vaporization and sublimation enthalpies compare favorably to the most of the literature values for the racemic form of ibuprofen but differ from the value reported for chiral ibuprofen. The literature values of (S)-naproxen are somewhat smaller than the values measured in this work. The following vaporization enthalpies were measured for (S)-ibuprofen and (S)-naproxen, respectively: ΔH(vap) (298.15 K), 106.0 ± 5.5, 132.2 ± 5.0 kJ·mol(-1) . Sublimation enthalpies of 122.7 ± 5.6 and 155.2 ± 7.1 kJ·mol(-1) were calculated for the (S)-enantiomers of ibuprofen and naproxen and a value of 128.9 ± 5.8 kJ·mol(-1) was estimated for the racemic form of ibuprofen. Copyright © 2011 Wiley Periodicals, Inc.

Progress toward a performance based specification for diamond grinding wheels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, J.S.; Piscotty, M.S.; Blaedel, K.L.

1996-11-12

This work sought to improve the communication between users and makers of fine diamond grinding wheels. A promising avenue for this is to formulate a voluntary product standard that comprises performance indicators that bridge the gap between specific user requirements and the details of wheel formulations. We propose a set of performance specifiers of figures-of-merit, that might be assessed by straightforward and traceable testing methods, but do not compromise proprietary information of the wheel user of wheel maker. One such performance indicator might be wheel hardness. In addition we consider technologies that might be required to realize the benefits ofmore » optimized grinding wheels. A non-contact wheel-to- workpiece proximity sensor may provide a means of monitoring wheel wear and thus wheel position, for wheels that exhibit high wear rates in exchange for improved surface finish.« less

Miniature pipe crawler tractor

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKay, M.D.; Anderson, M.O.; Ferrante, T.A.

2000-03-14

A pipe crawler tractor may comprise a half tractor assembly having a first base drive wheel, a second base drive wheel, and a top drive wheel. The drive wheels are mounted in spaced-apart relation so that the top drive wheel is positioned between the first and second base drive wheels. The mounting arrangement is also such that the first and second base drive wheels contact the inside surface of the pipe at respective first and second positions and so that the top drive wheel contacts the inside surface of the pipe at a third position, the third position being substantiallymore » diametrically opposed to the first and second positions. A control system connected to the half tractor assembly controls the rotation of the first base wheel, the second base wheel, and the top drive wheel to move the half tractor assembly within the pipe.« less

Enthalpy of sublimation as measured using a silicon oscillator

NASA Astrophysics Data System (ADS)

Shakeel, Hamza; Pomeroy, J. M.

In this study, we report the enthalpy of sublimation of common gases (nitrogen, oxygen, argon, carbon dioxide, neon, krypton, xenon, and water vapor) using a large area silicon oscillator with a sub-ng (~0.027 ng/cm2) mass sensitivity. The double paddle oscillator design enables high frequency stability (17 ppb) at cryogenic temperatures and provides a consistent technique for enthalpy measurements. The enthalpies of sublimation are derived from the rate of mass loss during programmed thermal desorption and are detected as a change in the resonance frequency of the self-tracking oscillator. These measured enthalpy values show excellent agreement with the accepted literature values.

Enthalpies of a binary alloy during solidification

NASA Technical Reports Server (NTRS)

Poirier, D. R.; Nandapurkar, P.

1988-01-01

The purpose of the paper is to present a method of calculating the enthalpy of a dendritic alloy during solidification. The enthalpies of the dendritic solid and interdendritic liquid of alloys of the Pb-Sn system are evaluated, but the method could be applied to other binaries, as well. The enthalpies are consistent with a recent evaluation of the thermodynamics of Pb-Sn alloys and with the redistribution of solute in the same during dendritic solidification. Because of the heat of mixing in Pb-Sn alloys, the interdendritic liquid of hypoeutectic alloys (Pb-rich) of less than 50 wt pct Sn has enthalpies that increase as temperature decreases during solidification.

Modelling of Dynamics of a Wheeled Mobile Robot with Mecanum Wheels with the use of Lagrange Equations of the Second Kind

NASA Astrophysics Data System (ADS)

Hendzel, Z.; Rykała, Ł.

2017-02-01

The work presents the dynamic equations of motion of a wheeled mobile robot with mecanum wheels derived with the use of Lagrange equations of the second kind. Mecanum wheels are a new type of wheels used in wheeled mobile robots and they consist of freely rotating rollers attached to the circumference of the wheels. In order to derive dynamic equations of motion of a wheeled mobile robot, the kinetic energy of the system is determined, as well as the generalised forces affecting the system. The resulting mathematical model of a wheeled mobile robot was generated with the use of Maple V software. The results of a solution of inverse and forward problems of dynamics of the discussed object are also published.

Reinforcement value and substitutability of sucrose and wheel running: implications for activity anorexia.

PubMed

Belke, Terry W; Pierce, W David; Duncan, Ian D

2006-09-01

Choice between sucrose and wheel-running reinforcement was assessed in two experiments. In the first experiment, ten male Wistar rats were exposed to concurrent VI 30 s VI 30 s schedules of wheel-running and sucrose reinforcement. Sucrose concentration varied across concentrations of 2.5, 7.5, and 12.5%. As concentration increased, more behavior was allocated to sucrose and more reinforcements were obtained from that alternative. Allocation of behavior to wheel running decreased, but obtained wheel-running reinforcement did not change. Overall, the results suggested that food-deprived rats were sensitive to qualitative changes in food supply (sucrose concentration) while continuing to defend a level of physical activity (wheel running). In the second study, 15 female Long Evans rats were exposed to concurrent variable ratio schedules of sucrose and wheel-running, wheel-running and wheel-running, and sucrose and sucrose reinforcement. For each pair of reinforcers, substitutability was assessed by the effect of income-compensated price changes on consumption of the two reinforcers. Results showed that, as expected, sucrose substituted for sucrose and wheel running substituted for wheel running. Wheel running, however, did not substitute for sucrose; but sucrose partially substituted for wheel running. We address the implications of the interrelationships of sucrose and wheel running for an understanding of activity anorexia.

Reinforcement Value and Substitutability of Sucrose and Wheel Running: Implications for Activity Anorexia

PubMed Central

Belke, Terry W; Duncan, Ian D; David Pierce, W

2006-01-01

Choice between sucrose and wheel-running reinforcement was assessed in two experiments. In the first experiment, ten male Wistar rats were exposed to concurrent VI 30 s VI 30 s schedules of wheel-running and sucrose reinforcement. Sucrose concentration varied across concentrations of 2.5, 7.5, and 12.5%. As concentration increased, more behavior was allocated to sucrose and more reinforcements were obtained from that alternative. Allocation of behavior to wheel running decreased, but obtained wheel-running reinforcement did not change. Overall, the results suggested that food-deprived rats were sensitive to qualitative changes in food supply (sucrose concentration) while continuing to defend a level of physical activity (wheel running). In the second study, 15 female Long Evans rats were exposed to concurrent variable ratio schedules of sucrose and wheel-running, wheel-running and wheel-running, and sucrose and sucrose reinforcement. For each pair of reinforcers, substitutability was assessed by the effect of income-compensated price changes on consumption of the two reinforcers. Results showed that, as expected, sucrose substituted for sucrose and wheel running substituted for wheel running. Wheel running, however, did not substitute for sucrose; but sucrose partially substituted for wheel running. We address the implications of the interrelationships of sucrose and wheel running for an understanding of activity anorexia. PMID:17002224

Design and manufacture of wheels for a dual-mode (manned - automatic) lunar surface roving vehicle. Volume 1: Detailed technical report

NASA Technical Reports Server (NTRS)

1970-01-01

The concept development, testing, evaluation, and the selection of a final wheel design concept for a dual-mode lunar surface vehicle (DLRV) is detailed. Four wheel configurations were fabricated (one open wheel and three closed wheel) (and subjected to a series of soft soil, mechanical, and endurance tests. Results show that the open wheel has lower draw-bar pull (slope climbing) capability in loose soil due to its higher ground pressure and tendency to dig in at high wheel slip. Endurance tests indicate that a double mesh, fully enclosed wheel can be developed to meet DLRV life requirements. There is, however, a 1.0 to 1.8 lb/wheel weight penalty associated with the wheel enclosure. Also the button cleats used as grousers for the closed-type wheels result in local stress concentration and early fatigue failure of the wire mesh. Load deflection tests indicate that the stiffness of the covered wheel increased by up to 50% after soil bin testing, due to increased friction between the fabric and the wire mesh caused by the sand. No change in stiffness was found for the open wheel. The single woven mesh open wheel design with a chevron tread is recommended for continued development

Experimental formation enthalpies for intermetallic phases and other inorganic compounds

PubMed Central

Kim, George; Meschel, S. V.; Nash, Philip; Chen, Wei

2017-01-01

The standard enthalpy of formation of a compound is the energy associated with the reaction to form the compound from its component elements. The standard enthalpy of formation is a fundamental thermodynamic property that determines its phase stability, which can be coupled with other thermodynamic data to calculate phase diagrams. Calorimetry provides the only direct method by which the standard enthalpy of formation is experimentally measured. However, the measurement is often a time and energy intensive process. We present a dataset of enthalpies of formation measured by high-temperature calorimetry. The phases measured in this dataset include intermetallic compounds with transition metal and rare-earth elements, metal borides, metal carbides, and metallic silicides. These measurements were collected from over 50 years of calorimetric experiments. The dataset contains 1,276 entries on experimental enthalpy of formation values and structural information. Most of the entries are for binary compounds but ternary and quaternary compounds are being added as they become available. The dataset also contains predictions of enthalpy of formation from first-principles calculations for comparison. PMID:29064466

Maximum Torque and Momentum Envelopes for Reaction Wheel Arrays

NASA Technical Reports Server (NTRS)

Markley, F. Landis; Reynolds, Reid G.; Liu, Frank X.; Lebsock, Kenneth L.

2009-01-01

Spacecraft reaction wheel maneuvers are limited by the maximum torque and/or angular momentum that the wheels can provide. For an n-wheel configuration, the torque or momentum envelope can be obtained by projecting the n-dimensional hypercube, representing the domain boundary of individual wheel torques or momenta, into three dimensional space via the 3xn matrix of wheel axes. In this paper, the properties of the projected hypercube are discussed, and algorithms are proposed for determining this maximal torque or momentum envelope for general wheel configurations. Practical strategies for distributing a prescribed torque or momentum among the n wheels are presented, with special emphasis on configurations of four, five, and six wheels.

Thermodynamics of the Sorption of Benzimidazoles on Octadecyl Silica Gel from Water-Methanol Eluents

NASA Astrophysics Data System (ADS)

Shafigulin, R. V.; Bulanova, A. V.

2018-02-01

The standard enthalpy and entropy component of transferring benzimidazoles from water-methanol solutions to surfaces of octadecyl silica gel are determined using reversed-phase high-performance liquid chromatography (RP HPLC). The dependences between the enthalpy and polarizability of the molecules of the studied benzimidazoles, the enthalpy and the entropy factor are studied, and the influence of the quantitative composition of the water-methanol solution on the enthalpy are studied.

Phase Transition Enthalpy Measurements of Organic and Organometallic Compounds. Sublimation, Vaporization and Fusion Enthalpies From 1880 to 2015. Part 1. C{sub 1} − C{sub 10}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Acree, William; Chickos, James S.

2016-09-15

A compendium of phase change enthalpies published in 2010 is updated to include the period 1880–2015. Phase change enthalpies including fusion, vaporization, and sublimation enthalpies are included for organic, organometallic, and a few inorganic compounds. Part 1 of this compendium includes organic compounds from C{sub 1} to C{sub 10}. Part 2 of this compendium, to be published separately, will include organic and organometallic compounds from C{sub 11} to C{sub 192}. Sufficient data are presently available to permit thermodynamic cycles to be constructed as an independent means of evaluating the reliability of the data. Temperature adjustments of phase change enthalpies frommore » the temperature of measurement to the standard reference temperature, T = 298.15 K, and a protocol for doing so are briefly discussed.« less

Flash Points of Secondary Alcohol and n-Alkane Mixtures.

PubMed

Esina, Zoya N; Miroshnikov, Alexander M; Korchuganova, Margarita R

2015-11-19

The flash point is one of the most important characteristics used to assess the ignition hazard of mixtures of flammable liquids. To determine the flash points of mixtures of secondary alcohols with n-alkanes, it is necessary to calculate the activity coefficients. In this paper, we use a model that allows us to obtain enthalpy of fusion and enthalpy of vaporization data of the pure components to calculate the liquid-solid equilibrium (LSE) and vapor-liquid equilibrium (VLE). Enthalpy of fusion and enthalpy of vaporization data of secondary alcohols in the literature are limited; thus, the prediction of these characteristics was performed using the method of thermodynamic similarity. Additionally, the empirical models provided the critical temperatures and boiling temperatures of the secondary alcohols. The modeled melting enthalpy and enthalpy of vaporization as well as the calculated LSE and VLE flash points were determined for the secondary alcohol and n-alkane mixtures.

Determination of vaporization enthalpies of polychlorinated biphenyls by correlation gas chromatography.

PubMed

Puri, S; Chickos, J S; Welsh, W J

2001-04-01

The vaporization enthalpies of 16 polychlorinated biphenyls have been determined by correlation gas chromatography. This study was prompted by the realization that the vaporization enthalpy of the standard compounds used in previous studies, octadecane and eicosane, were values measured at 340 and 362 K, respectively, rather than at 298 K. Adjustment to 298 K amounts to a 7-8 kJ/mol increment in the values. With the inclusion of this adjustment, vaporization enthalpies evaluated by correlation gas chromatography are in good agreement with the values determined previously in the literature. The present results are based on the vaporization enthalpies of several standards whose values are well established in the literature. The standards include a variety of n-alkanes and various chlorinated hydrocarbons. The vaporization enthalpies of PCBs increased with the number of chlorine atoms and were found to be larger for meta- and para-substituted polychlorinated biphenyls.

Enthalpies of Formation of Hydrazine and Its Derivatives.

PubMed

Dorofeeva, Olga V; Ryzhova, Oxana N; Suchkova, Taisiya A

2017-07-20

Enthalpies of formation, Δ f H 298 ° , in both the gas and condensed phase, and enthalpies of sublimation or vaporization have been estimated for hydrazine, NH 2 NH 2 , and its 36 various derivatives using quantum chemical calculations. The composite G4 method has been used along with isodesmic reaction schemes to derive a set of self-consistent high-accuracy gas-phase enthalpies of formation. To estimate the enthalpies of sublimation and vaporization with reasonable accuracy (5-20 kJ/mol), the method of molecular electrostatic potential (MEP) has been used. The value of Δ f H 298 ° (NH 2 NH 2 ,g) = 97.0 ± 3.0 kJ/mol was determined from 75 isogyric reactions involving about 50 reference species; for most of these species, the accurate Δ f H 298 ° (g) values are available in Active Thermochemical Tables (ATcT). The calculated value is in excellent agreement with the reported results of the most accurate models based on coupled cluster theory (97.3 kJ/mol, the average of six calculations). Thus, the difference between the values predicted by high-level theoretical calculations and the experimental value of Δ f H 298 ° (NH 2 NH 2 ,g) = 95.55 ± 0.19 kJ/mol recommended in the ATcT and other comprehensive reference sources is sufficiently large and requires further investigation. Different hydrazine derivatives have been also considered in this work. For some of them, both the enthalpy of formation in the condensed phase and the enthalpy of sublimation or vaporization are available; for other compounds, experimental data for only one of these properties exist. Evidence of accuracy of experimental data for the first group of compounds was provided by the agreement with theoretical Δ f H 298 ° (g) value. The unknown property for the second group of compounds was predicted using the MEP model. This paper presents a systematic comparison of experimentally determined enthalpies of formation and enthalpies of sublimation or vaporization with the results of calculations. Because of relatively large uncertainty in the estimated enthalpies of sublimation, it was not always possible to evaluate the accuracy of the experimental values; however, this model allowed us to detect large errors in the experimental data, as in the case of 5,5'-hydrazinebistetrazole. The enthalpies of formation and enthalpies of sublimation or vaporization have been predicted for the first time for ten hydrazine derivatives with no experimental data. A recommended set of self-consistent experimental and calculated gas-phase enthalpies of formation of hydrazine derivatives can be used as reference Δ f H 298 ° (g) values to predict the enthalpies of formation of various hydrazines by means of isodesmic reactions.

49 CFR 230.114 - Wheel centers.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., following the repair, the crankpin and axle shall remain tight in the wheel. Banding of the hub is permitted... 49 Transportation 4 2013-10-01 2013-10-01 false Wheel centers. 230.114 Section 230.114... Tenders Wheels and Tires § 230.114 Wheel centers. (a) Filling blocks and shims. Driving and trailing wheel...

49 CFR 230.114 - Wheel centers.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., following the repair, the crankpin and axle shall remain tight in the wheel. Banding of the hub is permitted... 49 Transportation 4 2014-10-01 2014-10-01 false Wheel centers. 230.114 Section 230.114... Tenders Wheels and Tires § 230.114 Wheel centers. (a) Filling blocks and shims. Driving and trailing wheel...

49 CFR 230.105 - Lateral motion.

Code of Federal Regulations, 2014 CFR

2014-10-01

... between the hubs of the wheels and the boxes on any pair of wheels shall not exceed the following limits: Inches Engine truck wheels (with swing centers) 1 Engine truck wheels (with rigid centers) 11/2 Trailing truck wheels 1 Driving wheels 3/4 (b) Limits increased. These limits may be increased on steam...

49 CFR 230.114 - Wheel centers.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., following the repair, the crankpin and axle shall remain tight in the wheel. Banding of the hub is permitted... 49 Transportation 4 2012-10-01 2012-10-01 false Wheel centers. 230.114 Section 230.114... Tenders Wheels and Tires § 230.114 Wheel centers. (a) Filling blocks and shims. Driving and trailing wheel...

49 CFR 230.105 - Lateral motion.

Code of Federal Regulations, 2010 CFR

2010-10-01

... between the hubs of the wheels and the boxes on any pair of wheels shall not exceed the following limits: Inches Engine truck wheels (with swing centers) 1 Engine truck wheels (with rigid centers) 11/2 Trailing truck wheels 1 Driving wheels 3/4 (b) Limits increased. These limits may be increased on steam...

49 CFR 230.105 - Lateral motion.

Code of Federal Regulations, 2011 CFR

2011-10-01

... between the hubs of the wheels and the boxes on any pair of wheels shall not exceed the following limits: Inches Engine truck wheels (with swing centers) 1 Engine truck wheels (with rigid centers) 11/2 Trailing truck wheels 1 Driving wheels 3/4 (b) Limits increased. These limits may be increased on steam...

49 CFR 230.114 - Wheel centers.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., following the repair, the crankpin and axle shall remain tight in the wheel. Banding of the hub is permitted... 49 Transportation 4 2011-10-01 2011-10-01 false Wheel centers. 230.114 Section 230.114... Tenders Wheels and Tires § 230.114 Wheel centers. (a) Filling blocks and shims. Driving and trailing wheel...

49 CFR 230.114 - Wheel centers.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., following the repair, the crankpin and axle shall remain tight in the wheel. Banding of the hub is permitted... 49 Transportation 4 2010-10-01 2010-10-01 false Wheel centers. 230.114 Section 230.114... Tenders Wheels and Tires § 230.114 Wheel centers. (a) Filling blocks and shims. Driving and trailing wheel...

49 CFR 230.105 - Lateral motion.

Code of Federal Regulations, 2012 CFR

2012-10-01

... between the hubs of the wheels and the boxes on any pair of wheels shall not exceed the following limits: Inches Engine truck wheels (with swing centers) 1 Engine truck wheels (with rigid centers) 11/2 Trailing truck wheels 1 Driving wheels 3/4 (b) Limits increased. These limits may be increased on steam...

49 CFR 230.105 - Lateral motion.

Code of Federal Regulations, 2013 CFR

2013-10-01

... between the hubs of the wheels and the boxes on any pair of wheels shall not exceed the following limits: Inches Engine truck wheels (with swing centers) 1 Engine truck wheels (with rigid centers) 11/2 Trailing truck wheels 1 Driving wheels 3/4 (b) Limits increased. These limits may be increased on steam...

Thermal fatigue performance of integrally cast automotive turbine wheels

NASA Technical Reports Server (NTRS)

Humphreys, V. E.; Hofer, K. E.

1980-01-01

Fluidized bed thermal fatigue testing was conducted on 16 integrally cast automotive turbine wheels for 1000-10,000 (600 sec total) thermal cycles at 935/50 C. The 16 wheels consisted of 14 IN-792 + 1% Hf and 2 gatorized AF2-1DA wheels; 6 of the IN-792 + Hf wheels contained crack arrest pockets inside the blade root flange. Temperature transients during the thermal cycling were measured in three calibration tests using either 18 or 30 thermocouples per wheel. Thermal cracking based on crack length versus accumulated cycles was greatest for unpocketed wheels developing cracks in 8-13 cycles compared to 75-250 cycles for unpocketed wheels. However, pocketed wheels survived up to 10,000 cycles with crack lengths less than 20 mm, whereas two unpocketed wheels developed 45 mm long cracks in 1000-2000 cycles.

Maximum Torque and Momentum Envelopes for Reaction Wheel Arrays

NASA Technical Reports Server (NTRS)

Reynolds, R. G.; Markley, F. Landis

2001-01-01

Spacecraft reaction wheel maneuvers are limited by the maximum torque and/or angular momentum which the wheels can provide. For an n-wheel configuration, the torque or momentum envelope can be obtained by projecting the n-dimensional hypercube, representing the domain boundary of individual wheel torques or momenta, into three dimensional space via the 3xn matrix of wheel axes. In this paper, the properties of the projected hypercube are discussed, and algorithms are proposed for determining this maximal torque or momentum envelope for general wheel configurations. Practical implementation strategies for specific wheel configurations are also considered.

Wheel speed management control system for spacecraft

NASA Technical Reports Server (NTRS)

Goodzeit, Neil E. (Inventor); Linder, David M. (Inventor)

1991-01-01

A spacecraft attitude control system uses at least four reaction wheels. In order to minimize reaction wheel speed and therefore power, a wheel speed management system is provided. The management system monitors the wheel speeds and generates a wheel speed error vector. The error vector is integrated, and the error vector and its integral are combined to form a correction vector. The correction vector is summed with the attitude control torque command signals for driving the reaction wheels.

Enthalpy of Mixing in Al–Tb Liquid

DOE PAGES

Zhou, Shihuai; Tackes, Carl; Napolitano, Ralph

2017-06-21

The liquid-phase enthalpy of mixing for Al$-$Tb alloys is measured for 3, 5, 8, 10, and 20 at% Tb at selected temperatures in the range from 1364 to 1439 K. Methods include isothermal solution calorimetry and isoperibolic electromagnetic levitation drop calorimetry. Mixing enthalpy is determined relative to the unmixed pure (Al and Tb) components. The required formation enthalpy for the Al3Tb phase is computed from first-principles calculations. Finally, based on our measurements, three different semi-empirical solution models are offered for the excess free energy of the liquid, including regular, subregular, and associate model formulations. These models are also compared withmore » the Miedema model prediction of mixing enthalpy.« less

Ionic liquids. Combination of combustion calorimetry with high-level quantum chemical calculations for deriving vaporization enthalpies.

PubMed

Emel'yanenko, Vladimir N; Verevkin, Sergey P; Heintz, Andreas; Schick, Christoph

2008-07-10

In this work, the molar enthalpies of formation of the ionic liquids [C2MIM][NO3] and [C4MIM][NO3] were measured by means of combustion calorimetry. The molar enthalpy of fusion of [C2MIM][NO3] was measured using differential scanning calorimetry. Ab initio calculations of the enthalpy of formation in the gaseous phase have been performed for the ionic species using the G3MP2 theory. We have used a combination of traditional combustion calorimetry with modern high-level ab initio calculations in order to obtain the molar enthalpies of vaporization of a series of the ionic liquids under study.

49 CFR 230.113 - Wheels and tire defects.

Code of Federal Regulations, 2012 CFR

2012-10-01

... crack or break in the flange, tread, rim, plate, hub or brackets. (b) Flat spots. Wheels and tires may... 49 Transportation 4 2012-10-01 2012-10-01 false Wheels and tire defects. 230.113 Section 230.113... Tenders Wheels and Tires § 230.113 Wheels and tire defects. Steam locomotive and tender wheels or tires...

49 CFR 215.103 - Defective wheel.

Code of Federal Regulations, 2012 CFR

2012-10-01

... less; (d) A wheel rim, flange, plate, or hub area on the car has a crack or break; (e) A wheel on the... 49 Transportation 4 2012-10-01 2012-10-01 false Defective wheel. 215.103 Section 215.103... § 215.103 Defective wheel. A railroad may not place or continue in service a car, if— (a) A wheel flange...

49 CFR 230.113 - Wheels and tire defects.

Code of Federal Regulations, 2010 CFR

2010-10-01

... crack or break in the flange, tread, rim, plate, hub or brackets. (b) Flat spots. Wheels and tires may... 49 Transportation 4 2010-10-01 2010-10-01 false Wheels and tire defects. 230.113 Section 230.113... Tenders Wheels and Tires § 230.113 Wheels and tire defects. Steam locomotive and tender wheels or tires...

49 CFR 215.103 - Defective wheel.

Code of Federal Regulations, 2011 CFR

2011-10-01

... less; (d) A wheel rim, flange, plate, or hub area on the car has a crack or break; (e) A wheel on the... 49 Transportation 4 2011-10-01 2011-10-01 false Defective wheel. 215.103 Section 215.103... § 215.103 Defective wheel. A railroad may not place or continue in service a car, if— (a) A wheel flange...

49 CFR 230.113 - Wheels and tire defects.

Code of Federal Regulations, 2014 CFR

2014-10-01

... crack or break in the flange, tread, rim, plate, hub or brackets. (b) Flat spots. Wheels and tires may... 49 Transportation 4 2014-10-01 2014-10-01 false Wheels and tire defects. 230.113 Section 230.113... Tenders Wheels and Tires § 230.113 Wheels and tire defects. Steam locomotive and tender wheels or tires...

49 CFR 230.113 - Wheels and tire defects.

Code of Federal Regulations, 2013 CFR

2013-10-01

... crack or break in the flange, tread, rim, plate, hub or brackets. (b) Flat spots. Wheels and tires may... 49 Transportation 4 2013-10-01 2013-10-01 false Wheels and tire defects. 230.113 Section 230.113... Tenders Wheels and Tires § 230.113 Wheels and tire defects. Steam locomotive and tender wheels or tires...

49 CFR 215.103 - Defective wheel.

Code of Federal Regulations, 2010 CFR

2010-10-01

... less; (d) A wheel rim, flange, plate, or hub area on the car has a crack or break; (e) A wheel on the... 49 Transportation 4 2010-10-01 2010-10-01 false Defective wheel. 215.103 Section 215.103... § 215.103 Defective wheel. A railroad may not place or continue in service a car, if— (a) A wheel flange...

49 CFR 230.113 - Wheels and tire defects.

Code of Federal Regulations, 2011 CFR

2011-10-01

... crack or break in the flange, tread, rim, plate, hub or brackets. (b) Flat spots. Wheels and tires may... 49 Transportation 4 2011-10-01 2011-10-01 false Wheels and tire defects. 230.113 Section 230.113... Tenders Wheels and Tires § 230.113 Wheels and tire defects. Steam locomotive and tender wheels or tires...

49 CFR 215.103 - Defective wheel.

Code of Federal Regulations, 2014 CFR

2014-10-01

... less; (d) A wheel rim, flange, plate, or hub area on the car has a crack or break; (e) A wheel on the... 49 Transportation 4 2014-10-01 2014-10-01 false Defective wheel. 215.103 Section 215.103... § 215.103 Defective wheel. A railroad may not place or continue in service a car, if— (a) A wheel flange...

49 CFR 215.103 - Defective wheel.

Code of Federal Regulations, 2013 CFR

2013-10-01

... less; (d) A wheel rim, flange, plate, or hub area on the car has a crack or break; (e) A wheel on the... 49 Transportation 4 2013-10-01 2013-10-01 false Defective wheel. 215.103 Section 215.103... § 215.103 Defective wheel. A railroad may not place or continue in service a car, if— (a) A wheel flange...

Free enthalpies of replacing water molecules in protein binding pockets.

PubMed

Riniker, Sereina; Barandun, Luzi J; Diederich, François; Krämer, Oliver; Steffen, Andreas; van Gunsteren, Wilfred F

2012-12-01

Water molecules in the binding pocket of a protein and their role in ligand binding have increasingly raised interest in recent years. Displacement of such water molecules by ligand atoms can be either favourable or unfavourable for ligand binding depending on the change in free enthalpy. In this study, we investigate the displacement of water molecules by an apolar probe in the binding pocket of two proteins, cyclin-dependent kinase 2 and tRNA-guanine transglycosylase, using the method of enveloping distribution sampling (EDS) to obtain free enthalpy differences. In both cases, a ligand core is placed inside the respective pocket and the remaining water molecules are converted to apolar probes, both individually and in pairs. The free enthalpy difference between a water molecule and a CH(3) group at the same location in the pocket in comparison to their presence in bulk solution calculated from EDS molecular dynamics simulations corresponds to the binding free enthalpy of CH(3) at this location. From the free enthalpy difference and the enthalpy difference, the entropic contribution of the displacement can be obtained too. The overlay of the resulting occupancy volumes of the water molecules with crystal structures of analogous ligands shows qualitative correlation between experimentally measured inhibition constants and the calculated free enthalpy differences. Thus, such an EDS analysis of the water molecules in the binding pocket may give valuable insight for potency optimization in drug design.

Free enthalpies of replacing water molecules in protein binding pockets

NASA Astrophysics Data System (ADS)

Riniker, Sereina; Barandun, Luzi J.; Diederich, François; Krämer, Oliver; Steffen, Andreas; van Gunsteren, Wilfred F.

2012-12-01

Water molecules in the binding pocket of a protein and their role in ligand binding have increasingly raised interest in recent years. Displacement of such water molecules by ligand atoms can be either favourable or unfavourable for ligand binding depending on the change in free enthalpy. In this study, we investigate the displacement of water molecules by an apolar probe in the binding pocket of two proteins, cyclin-dependent kinase 2 and tRNA-guanine transglycosylase, using the method of enveloping distribution sampling (EDS) to obtain free enthalpy differences. In both cases, a ligand core is placed inside the respective pocket and the remaining water molecules are converted to apolar probes, both individually and in pairs. The free enthalpy difference between a water molecule and a CH3 group at the same location in the pocket in comparison to their presence in bulk solution calculated from EDS molecular dynamics simulations corresponds to the binding free enthalpy of CH3 at this location. From the free enthalpy difference and the enthalpy difference, the entropic contribution of the displacement can be obtained too. The overlay of the resulting occupancy volumes of the water molecules with crystal structures of analogous ligands shows qualitative correlation between experimentally measured inhibition constants and the calculated free enthalpy differences. Thus, such an EDS analysis of the water molecules in the binding pocket may give valuable insight for potency optimization in drug design.

Design of a robotic vehicle with self-contained intelligent wheels

NASA Astrophysics Data System (ADS)

Poulson, Eric A.; Jacob, John S.; Gunderson, Robert W.; Abbott, Ben A.

1998-08-01

The Center for Intelligent Systems has developed a small robotic vehicle named the Advanced Rover Chassis 3 (ARC 3) with six identical intelligent wheel units attached to a payload via a passive linkage suspension system. All wheels are steerable, so the ARC 3 can move in any direction while rotating at any rate allowed by the terrain and motors. Each intelligent wheel unit contains a drive motor, steering motor, batteries, and computer. All wheel units are identical, so manufacturing, programing, and spare replacement are greatly simplified. The intelligent wheel concept would allow the number and placement of wheels on the vehicle to be changed with no changes to the control system, except to list the position of all the wheels relative to the vehicle center. The task of controlling the ARC 3 is distributed between one master computer and the wheel computers. Tasks such as controlling the steering motors and calculating the speed of each wheel relative to the vehicle speed in a corner are dependent on the location of a wheel relative to the vehicle center and ar processed by the wheel computers. Conflicts between the wheels are eliminated by computing the vehicle velocity control in the master computer. Various approaches to this distributed control problem, and various low level control methods, have been explored.

Effect of sucrose availability and pre-running on the intrinsic value of wheel running as an operant and a reinforcing consequence.

PubMed

Belke, Terry W; Pierce, W David

2014-03-01

The current study investigated the effect of motivational manipulations on operant wheel running for sucrose reinforcement and on wheel running as a behavioral consequence for lever pressing, within the same experimental context. Specifically, rats responded on a two-component multiple schedule of reinforcement in which lever pressing produced the opportunity to run in a wheel in one component of the schedule (reinforcer component) and wheel running produced the opportunity to consume sucrose solution in the other component (operant component). Motivational manipulations involved removal of sucrose contingent on wheel running and providing 1h of pre-session wheel running. Results showed that, in opposition to a response strengthening view, sucrose did not maintain operant wheel running. The motivational operations of withdrawing sucrose or providing pre-session wheel running, however, resulted in different wheel-running rates in the operant and reinforcer components of the multiple schedule; this rate discrepancy revealed the extrinsic reinforcing effects of sucrose on operant wheel running, but also indicated the intrinsic reinforcement value of wheel running across components. Differences in wheel-running rates between components were discussed in terms of arousal, undermining of intrinsic motivation, and behavioral contrast. Copyright © 2013 Elsevier B.V. All rights reserved.

C57 mice increase wheel-running behavior following stress: preliminary findings.

PubMed

Sibold, Jeremy S; Hammack, Sayamwong E; Falls, William A

2011-10-01

Exercise has been shown to reduce anxiety in both humans and animals. To date, there are few, if any studies that examine the effect of stress on self-selected exercise using an animal model. This study examined the effect of acute stress on wheel-running distance in mice. Forty 8-week-old, male C57BL/6J mice were randomly assigned to one of three groups: no stress + wheel-running experience, stress + wheel-running experience, or stress with no wheel-running experience. Stressed mice were exposed to foot shock in a brightly lit environment. Following treatment, wheel-running distances were observed for three hours. Stress significantly increased voluntary wheel-running in mice with wheel-running experience as compared to nonstressed controls and stressed mice with no wheel-running experience. These results suggest that mice familiar with wheel-running may self-select this exercise as a modality for the mitigation of accumulated anxiety.

Mobility performance analysis of an innovation lunar rover with diameter-variable wheel

NASA Astrophysics Data System (ADS)

Sun, Gang; Gao, Feng; Sun, Peng; Xu, Guoyan

2007-11-01

To achieve excellent mobility performance, a four-wheel, all-wheel drive lunar rover with diameter-variable wheel was presented, the wheel can be contracted and extended by the motor equipped in the wheel hub, accompanied with wheel diameter varying from 200mm to 390mm. The wheel sinkage and drawbar pull force were predicated with terramechanics formulae and lunar regolith mechanic parameters employed, furthermore, the slope traversability was investigated through quasi-static modeling mechanic analysis, also the obstacle resistance and the maximum negotiable obstacle height for different wheel radius were derived from the equations of static equilibrium of the rover. Analysis results show that for the innovation lunar rover presented, it will bring much better slope traveling stability and obstacle climbing capability than rovers with normal wheels, these will improve the rover mobility performance and stabilize the rover's frame, smooth the motion of sensors.

Technics study on high accuracy crush dressing and sharpening of diamond grinding wheel

NASA Astrophysics Data System (ADS)

Jia, Yunhai; Lu, Xuejun; Li, Jiangang; Zhu, Lixin; Song, Yingjie

2011-05-01

Mechanical grinding of artificial diamond grinding wheel was traditional wheel dressing process. The rotate speed and infeed depth of tool wheel were main technics parameters. The suitable technics parameters of metals-bonded diamond grinding wheel and resin-bonded diamond grinding wheel high accuracy crush dressing were obtained by a mount of experiment in super-hard material wheel dressing grind machine and by analysis of grinding force. In the same time, the effect of machine sharpening and sprinkle granule sharpening was contrasted. These analyses and lots of experiments had extent instruction significance to artificial diamond grinding wheel accuracy crush dressing.

Going full circle: phase-transition thermodynamics of ionic liquids.

PubMed

Preiss, Ulrich; Verevkin, Sergey P; Koslowski, Thorsten; Krossing, Ingo

2011-05-27

We present the full enthalpic phase transition cycle for ionic liquids (ILs) as examples of non-classical salts. The cycle was closed for the lattice, solvation, dissociation, and vaporization enthalpies of 30 different ILs, relying on as much experimental data as was available. High-quality dissociation enthalpies were calculated at the G3 MP2 level. From the cycle, we could establish, for the first time, the lattice and solvation enthalpies of ILs with imidazolium ions. For vaporization, lattice, and dissociation enthalpies, we also developed new prediction methods in the course of our investigations. Here, as only single-ion values need to be calculated and the tedious optimization of an ion pair can be circumvented, the computational time is short. For the vaporization enthalpy, a very simple approach was found, using a surface term and the calculated enthalpic correction to the total gas-phase energy. For the lattice enthalpy, the most important constituent proved to be the calculated conductor-like screening model (COSMO) solvation enthalpy in the ideal electric conductor. A similar model was developed for the dissociation enthalpy. According to our assessment, the typical error of the lattice enthalpy would be 9.4 kJ mol(-1), which is less than half the deviation we get when using the (optimized) Kapustinskii equation or the recent volume-based thermodynamics (VBT) theory. In contrast, the non-optimized VBT formula gives lattice enthalpies 20 to 140 kJ mol(-1) lower than the ones we assessed in the cycle, because of the insufficient description of dispersive interactions. Our findings show that quantum-chemical calculations can greatly improve the VBT approaches, which were parameterized for simple, inorganic salts with ideally point-shaped charges. In conclusion, we suggest the term "augmented VBT", or "aVBT", to describe this kind of theoretical approach. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Increase of stagnation pressure and enthalpy in shock tunnels

NASA Technical Reports Server (NTRS)

Bogdanoff, David W.; Cambier, Jean-Luc

1992-01-01

High stagnation pressures and enthalpies are required for the testing of aerospace vehicles such as aerospace planes, aeroassist vehicles, and reentry vehicles. Among the most useful ground test facilities for performing such tests are shock tunnels. With a given driver gas condition, the enthalpy and pressure in the driven tube nozzle reservoir condition can be varied by changing the driven tube geometry and initial gas fill pressure. Reducing the driven tube diameter yields only very modest increases in reservoir pressure and enthalpy. Reducing the driven tube initial gas fill pressure can increase the reservoir enthalpy significantly, but at the cost of reduced reservoir pressure and useful test time. A new technique, the insertion of a converging section in the driven tube is found to produce substantial increases in both reservoir pressure and enthalpy. Using a one-dimensional inviscid full kinetics code, a number of different locations and shapes for the converging driven tube section were studied and the best cases found. For these best cases, for driven tube diameter reductions of factors of 2 and 3, the reservoir pressure can be increased by factors of 2.1 and 3.2, respectively and the enthalpy can be increased by factors of 1.5 and 2.1, respectively.

An examination of the thermodynamics of fusion, vaporization, and sublimation of several parabens by correlation gas chromatography.

PubMed

Umnahanant, Patamaporn; Chickos, James

2011-05-01

The vaporization, fusion, and sublimation enthalpies of methyl, ethyl, propyl, and butyl paraben are reported and compared with literature values. The vaporization enthalpies were measured by correlation gas chromatography and the fusion enthalpies by differential scanning calorimetry. Adjusted to T = 298.15 K, these enthalpies were combined to yield the sublimation enthalpy. The results compare favorably to some of the literature values but do not support the reversal in magnitude of both the vaporization and sublimation enthalpy previously reported for propyl and butyl paraben. The following fusion and vaporization enthalpies were measured for methyl through to butyl paraben, respectively: ΔH(fus) (T(fus) ) 26.3 ± 0.1 (398.6 K), 26.5 ± 0.1 (388.5 K), 27.3 ± 0.1 (368.8), and 25.9 ± 0.3 (340.7 K) kJ·mol(-1); ΔH(vap) (298.15 K) 79.5 ± 0.5, 84.0 ± 0.5, 89.7 ± 0.6, and 95.8 ± 0.6 kJ·mol(-1). The results are believed to be accurate to ± 4 kJ·mol(-1). Copyright © 2011 Wiley-Liss, Inc.

A dynamic wheel-rail impact analysis of railway track under wheel flat by finite element analysis

NASA Astrophysics Data System (ADS)

Bian, Jian; Gu, Yuantong; Murray, Martin Howard

2013-06-01

Wheel-rail interaction is one of the most important research topics in railway engineering. It involves track impact response, track vibration and track safety. Track structure failures caused by wheel-rail impact forces can lead to significant economic loss for track owners through damage to rails and to the sleepers beneath. Wheel-rail impact forces occur because of imperfections in the wheels or rails such as wheel flats, irregular wheel profiles, rail corrugations and differences in the heights of rails connected at a welded joint. A wheel flat can cause a large dynamic impact force as well as a forced vibration with a high frequency, which can cause damage to the track structure. In the present work, a three-dimensional finite element (FE) model for the impact analysis induced by the wheel flat is developed by the use of the FE analysis (FEA) software package ANSYS and validated by another validated simulation. The effect of wheel flats on impact forces is thoroughly investigated. It is found that the presence of a wheel flat will significantly increase the dynamic impact force on both rail and sleeper. The impact force will monotonically increase with the size of wheel flats. The relationships between the impact force and the wheel flat size are explored from this FEA and they are important for track engineers to improve their understanding of the design and maintenance of the track system.

Out-of-round railway wheels—assessment of wheel tread irregularities in train traffic

NASA Astrophysics Data System (ADS)

Johansson, Anders

2006-06-01

Results from an extensive wheel measurement campaign performed in Sweden are given and discussed. Out-of-roundness (OOR), transverse profile and surface hardness of 99 wheels on passenger trains (X2 and intercity), freight trains, commuter trains (Regina) and underground trains (C20) were measured. Both tread and disc braked wheels were investigated. The selected wheels had travelled a distance of more than 100000 km, and the measurements were conducted when the train wagons/coaches had been taken out of traffic for maintenance, most of them due to reasons other than wheel OOR. Mechanical contact measurement methods were used. The highest roughness levels (higher than 20 dB re 1 μm for some wheels) were found on powered high-speed (X2) train wheels. The previously known polygonalization of C20 underground wheels is quantified. It is also verified that an initial irregularity is formed due to the clamping in a three-jaw chuck during profiling of new C20 wheels. Magnitudes and wavelength contents of measured wheel roughness are compared with corresponding measurements of rail roughness.

A mechanical model for deformable and mesh pattern wheel of lunar roving vehicle

NASA Astrophysics Data System (ADS)

Liang, Zhongchao; Wang, Yongfu; Chen, Gang (Sheng); Gao, Haibo

2015-12-01

As an indispensable tool for astronauts on lunar surface, the lunar roving vehicle (LRV) is of great significance for manned lunar exploration. An LRV moves on loose and soft lunar soil, so the mechanical property of its wheels directly affects the mobility performance. The wheels used for LRV have deformable and mesh pattern, therefore, the existing mechanical theory of vehicle wheel cannot be used directly for analyzing the property of LRV wheels. In this paper, a new mechanical model for LRV wheel is proposed. At first, a mechanical model for a rigid normal wheel is presented, which involves in multiple conventional parameters such as vertical load, tangential traction force, lateral force, and slip ratio. Secondly, six equivalent coefficients are introduced to amend the rigid normal wheel model to fit for the wheels with deformable and mesh-pattern in LRV application. Thirdly, the values of the six equivalent coefficients are identified by using experimental data obtained in an LRV's single wheel testing. Finally, the identified mechanical model for LRV's wheel with deformable and mesh pattern are further verified and validated by using additional experimental results.

High-Clearance Six-Wheel Suspension

NASA Technical Reports Server (NTRS)

Bickler, Donald B.

1992-01-01

Multilevered suspension system gives body of vehicle high clearance and allows wheels to be steered independently. Suspension linkages above wheels enable body to skim over obstacles as high as wheel. Levers and independently steered wheels enable vehicle to climb steps 1 1/2 wheel diameters high and cross gaps 1 3/4 wide. Adaptable to off-the-road recreational vehicles, military scout vehicles, and robotic emergency vehicles.

Aerodynamic Drag Reduction Apparatus For Wheeled Vehicles In Ground Effect

DOEpatents

Ortega, Jason M.; Salari, Kambiz

2005-12-13

An apparatus for reducing the aerodynamic drag of a wheeled vehicle in a flowstream, the vehicle having a vehicle body and a wheel assembly supporting the vehicle body. The apparatus includes a baffle assembly adapted to be positioned upstream of the wheel assembly for deflecting airflow away from the wheel assembly so as to reduce the incident pressure on the wheel assembly.

77 FR 70478 - RG Steel Wheeling, LLC, Wheeling Office, A Division Of RG Steel, LLC, Including On-Site Leased...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-26

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-81,880: TA-A-81,880A] RG Steel Wheeling, LLC, Wheeling Office, A Division Of RG Steel, LLC, Including On-Site Leased Workers From Pro Unlimited and Green Energy Initiatives LLC, Including Workers Whose Wages Were Reported Through Severstal Wheeling, Wheeling, WV: Mountain State...

Propulsion and Levitation with a Large Electrodynamic Wheel

NASA Astrophysics Data System (ADS)

Gaul, Nathan; Lane, Hannah

We constructed an electrodynamic wheel using a motorized bicycle wheel with a radius of 12 inches and 36 one-inch cube magnets attached to the rim of the wheel. The radial magnetic field on the outside of the wheel was maximized by arranging the magnets into a series of Halbach arrays which amplify the field on one side of the array and reduce it on the other side. Rotating the wheel produces a rapidly oscillating magnetic field. When a conductive metal ``track'' is placed in this area of strong magnetic flux, eddy currents are produced in the track. These eddy currents create magnetic fields that interact with the magnetic fields from the electrodynamic wheel. The interaction of the magnetic fields produces lift and drag forces on the track which were measured with force gauges. Measurements were taken at a variety of wheel speeds, and the results were compared to the theoretical prediction that there should be a linear relationship between the lift and drag forces with increasing wheel speed. Partial levitation was achieved with the current electrodynamic wheel. In the future, the wheel will be upgraded to include 72 magnets rather than 36 magnets. This will double the frequency at which the magnetic field oscillates, increasing the magnetic flux. Electrodynamic wheels have applications to the transportation industry, since multiple electrodynamic wheels could be used on a vehicle to produce a lift and propulsion force over a conductive track.

76 FR 73596 - Notice of Scope Rulings

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-29

... LLC and OTR Wheel Engineering, Inc.; its wheel hub units/assemblies with tapered roller bearings are...-601: Tapered Roller Bearings from the People's Republic of China Requestor: New Trend Engineering... Requestor: OTR Wheel Engineering, Inc. (``OTR Wheel''); whether OTR Wheel's ``Trac Master'' and ``Traction...

Investigation of the effects of sliding on wheel tread damage

DOT National Transportation Integrated Search

2005-11-05

Wheel tread spalling is the main source of damage to wheel treads and : a primary cause for wheel removals from service. Severe frictional : heating of the wheel-rail contact patch during sliding causes the : formation of martensite, a hard, brittle ...

Thermodynamic Properties of M2EO4, M2Mo x O3 x + 1 and Double Chromates (M = Li, Na, K, Rb, Cs; E = Cr, Mo, W)

NASA Astrophysics Data System (ADS)

Suponitskiy, Yu. L.; Zolotova, E. S.; Dyunin, A. G.; Liashenko, S. E.

2018-03-01

The phase transition temperatures of chromates and molybdates of certain alkali metals, and the melting temperature and enthalpy of polymorphic transformations for tungstates, are determined by means of thermal analysis. Enthalpies of dissolution of rubidium and cesium chromates in water and enthalpies of dissolution of alkali metal tungstates in a melt at 923 K are measured via calorimetry. Standard enthalpies of formation of sought chromates are calculated. The linear correlations between the enthalpies of formation of sulfates, selenates, chromates, tungstates, and molybdates are established, and a linear correlation within - (Δ G o ox)-1-(Δ MV)ox)-1 coordinates is found for isopolymolybdates.

Stabilizing Wheels For Rover Vehicle

NASA Technical Reports Server (NTRS)

Collins, Earl R., Jr.

1990-01-01

Proposed articulated, normally-four-wheeled vehicle holds extra pair of wheels in reserve. Deployed to lengthen wheelbase on slopes, thereby making vehicle more stable, and to aid vehicle in negotiating ledge or to right vehicle if turned upside down. Extra wheels are drive wheels mounted on arms so they pivot on axis of forward drive wheels. Both extra wheels and arms driven by chains, hydraulic motors, or electric motors. Concept promises to make remotely controlled vehicles more stable and maneuverable in such applications as firefighting, handling hazardous materials, and carrying out operations in dangerous locations.

Characterizing Wheel-Soil Interaction Loads Using Meshfree Finite Element Methods: A Sensitivity Analysis for Design Trade Studies

NASA Technical Reports Server (NTRS)

Contreras, Michael T.; Trease, Brian P.; Bojanowski, Cezary; Kulakx, Ronald F.

2013-01-01

A wheel experiencing sinkage and slippage events poses a high risk to planetary rover missions as evidenced by the mobility challenges endured by the Mars Exploration Rover (MER) project. Current wheel design practice utilizes loads derived from a series of events in the life cycle of the rover which do not include (1) failure metrics related to wheel sinkage and slippage and (2) performance trade-offs based on grouser placement/orientation. Wheel designs are rigorously tested experimentally through a variety of drive scenarios and simulated soil environments; however, a robust simulation capability is still in development due to myriad of complex interaction phenomena that contribute to wheel sinkage and slippage conditions such as soil composition, large deformation soil behavior, wheel geometry, nonlinear contact forces, terrain irregularity, etc. For the purposes of modeling wheel sinkage and slippage at an engineering scale, meshfree nite element approaches enable simulations that capture su cient detail of wheel-soil interaction while remaining computationally feasible. This study implements the JPL wheel-soil benchmark problem in the commercial code environment utilizing the large deformation modeling capability of Smooth Particle Hydrodynamics (SPH) meshfree methods. The nominal, benchmark wheel-soil interaction model that produces numerically stable and physically realistic results is presented and simulations are shown for both wheel traverse and wheel sinkage cases. A sensitivity analysis developing the capability and framework for future ight applications is conducted to illustrate the importance of perturbations to critical material properties and parameters. Implementation of the proposed soil-wheel interaction simulation capability and associated sensitivity framework has the potential to reduce experimentation cost and improve the early stage wheel design proce

Effect of N-Methyl Substitution in the Glycine Molecule on the Enthalpy of Dissolution in Mixed Water-Alcohol Solvents at 298.15 K

NASA Astrophysics Data System (ADS)

Badelin, V. G.; Smirnov, V. I.

2018-07-01

The enthalpies of dissolution of N-methylglycine in water + ethanol, water + (1-propanol) and water + (2-propanol) are determined via calorimetry at an alcohol concentration of x 2 = 0-0.25 mole fraction. The standard values of enthalpies of dissolution (Δ_{sol}H°) and transfer (Δ_{tr}H°) of N-methylglycine from water to solution are calculated. The effect the structure and properties of N-methylglycine and the composition of a water-alcohol mixture have on N-methylglycine's enthalpy characteristics is examined. The enthalpy coefficients of pair interactions ( h xy ) between N-methylglycine and alcohol molecules are calculated. They have positive values and grow in the series ethanol (EtOH) < 1-propanol (1-PrOH), < 2-propanol (2-PrOH). A comparative analysis is performed of the enthalpy characteristics of dissolution and transfer of N-methylglycine and the analogous characteristics of glycine and DL-α-alanine in similar mixtures.

Heat Effect of the Protonation of Glycine and the Enthalpies of Resolvation of Participating Chemical Species in Water-Dimethylsulfoxide Solvent Mixtures

NASA Astrophysics Data System (ADS)

Isaeva, V. A.; Sharnin, V. A.

2018-02-01

Enthalpies of the protonation of glycine in water‒dimethylsulfoxide (DMSO) mixed solvents are determined calorimetrically in the range of DMSO mole fractions of 0.0 to 0.9, at T = 298.15 K and an ionic strength μ = 0.3 (NaClO4). It is established that the protonation of glycine becomes more exothermic with an increasing mole fraction of DMSO, and the enthalpies of resolvation of glycine and glycinium ions in water‒DMSO solvent mixtures are calculated. It is shown that the small changes in the enthalpy of protonation observed at low mole fractions of DMSO are caused by the contributions from the solvation of proton and protonated glycine cancelling each other out. The enthalpy term of the Gibbs energy of the reaction leading to the formation of glycinium ion is estimated along with the enthalpy of resolvation of the reacting species in the water‒DMSO mixed solvent.

49 CFR 570.10 - Wheel assemblies.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Wheel assemblies. 570.10 Section 570.10 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... Pounds or Less § 570.10 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc, or spider shall...

49 CFR 570.63 - Wheel assemblies.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 6 2013-10-01 2013-10-01 false Wheel assemblies. 570.63 Section 570.63 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... 10,000 Pounds § 570.63 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc or spider shall...

49 CFR 570.10 - Wheel assemblies.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 6 2014-10-01 2014-10-01 false Wheel assemblies. 570.10 Section 570.10 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... Pounds or Less § 570.10 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc, or spider shall...

49 CFR 570.63 - Wheel assemblies.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 6 2014-10-01 2014-10-01 false Wheel assemblies. 570.63 Section 570.63 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... 10,000 Pounds § 570.63 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc or spider shall...

49 CFR 570.63 - Wheel assemblies.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 6 2012-10-01 2012-10-01 false Wheel assemblies. 570.63 Section 570.63 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... 10,000 Pounds § 570.63 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc or spider shall...

49 CFR 570.10 - Wheel assemblies.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 6 2013-10-01 2013-10-01 false Wheel assemblies. 570.10 Section 570.10 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... Pounds or Less § 570.10 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc, or spider shall...

49 CFR 570.10 - Wheel assemblies.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 6 2011-10-01 2011-10-01 false Wheel assemblies. 570.10 Section 570.10 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... Pounds or Less § 570.10 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc, or spider shall...

49 CFR 570.10 - Wheel assemblies.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 6 2012-10-01 2012-10-01 false Wheel assemblies. 570.10 Section 570.10 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... Pounds or Less § 570.10 Wheel assemblies. (a) Wheel integrity. A tire rim, wheel disc, or spider shall...

Performance of the Boeing LRV wheels in a lunar soil simulant. Report 2: Effects of speed, Wheel load, and soil

NASA Technical Reports Server (NTRS)

Melzer, K.

1971-01-01

Two nearly identical Boeing-GM wire-mesh Lunar Roving Vehicle (LRV) wheels were laboratory tested in a lunar soil simulant to determine the influence of wheel speed and acceleration, wheel load, presence of a fender, travel direction, and soil strength on the wheel performance. Constant-slip and three types of programmed-slip tests were conducted with a single-wheel dynamometer system. Test results indicated that performance of single LRV wheels in terms of pull coefficient, power number, and efficiency were not influenced by wheel speed and acceleration, travel direction, the presence of a fender, or wheel load. Of these variables, only load influenced sinkage, which increased with increasing load. For a given slip, the pull coefficient and power number increased with increasing soil strength. However, for a given pull coefficient or slope, slip was less in firmer soil; thus, the power number decreased and efficiency increased with increasing soil strength.

The response of a high-speed train wheel to a harmonic wheel-rail force

NASA Astrophysics Data System (ADS)

Sheng, Xiaozhen; Liu, Yuxia; Zhou, Xin

2016-09-01

The maximum speed of China's high-speed trains currently is 300km/h and expected to increase to 350-400km/h. As a wheel travels along the rail at such a high speed, it is subject to a force rotating at the same speed along its periphery. This fast moving force contains not only the axle load component, but also many components of high frequencies generated from wheel-rail interactions. Rotation of the wheel also introduces centrifugal and gyroscopic effects. How the wheel responds is fundamental to many issues, including wheel-rail contact, traction, wear and noise. In this paper, by making use of its axial symmetry, a special finite element scheme is developed for responses of a train wheel subject to a vertical and harmonic wheel-rail force. This FE scheme only requires a 2D mesh over a cross-section containing the wheel axis but includes all the effects induced by wheel rotation. Nodal displacements, as a periodic function of the cross-section angle 6, can be decomposed, using Fourier series, into a number of components at different circumferential orders. The derived FE equation is solved for each circumferential order. The sum of responses at all circumferential orders gives the actual response of the wheel.

Enthalpy measurement of coal-derived liquids. Final report, April 1981-September 1983. [517 to 10342 kPa; 340 to 664 K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kidnay, A.J.; Yesavage, V.F.

This report summarizes the results of experimental measurements of enthalpies for quinoline using a freon boil-off flow calorimeter, and an investigation of the applicability of cubic equations of state to correlating the enthalpy of coal-liquids. In Part A the compound quinoline is discussed. Process flow in the flow calorimeter, operational problems, and equipment modifications are described. Procedural modifications, including a new sample purification procedure, are described. Part B discusses the correlational effort. This includes a discussion of past correlational work and the difficulties associated with a general correlation for coal liquid enthalpy. In addition experimental data and computer generated predictionsmore » are presented. Three equations of state were used to predict vapor pressures and enthalpies for ten pure component systems previously studied in the lab. In general, the results were encouraging. All three equations were found to be effective in predicting both enthalpies and vapor pressures. In addition, the equations worked well when fit to mixture enthalpies. The Modified SRK equation was found to be superior to the other equations and modeled all properties for both associating and nonassociating systems well. The Modified SRK equation did have a drawback in that it was not readily generalized since it required two parameters which must be fit to data for best results. In sum, it was shown that a four parameter equation of state could be used successfully to correlate the enthalpy of coal-liquid model compounds.« less

Measurements of the air conditioning capacity of the nose during normal and pathological conditions and pharmacological influence.

PubMed

Drettner, B; Falck, B; Simon, H

1977-01-01

A simple method is introduced for measuring the air conditioning capacity of the nose. A flow of 8 1/min dry air is introduced by a catheter into the nasopharynx, while 5 1/min is sucked out from the investigated nasal cavity through a psychrometer. The additional 3 1/min passes down into the pharynx, thus reducing the intermingling with expiratory air. By using CO2 as a tracer, this error was found to be maximally 15% and often about 1%. The three different enthalpy factors: increase in enthalpy of dry air, vaporization, and increase in enthalpy of water vapour, were calculated separately and the vaporization was found to be the dominant factor. The calculated total supply of humidity showed that the method presented causes at least a slight stress on the humidifying capacity. Pharmacological studies have shown that subcutaneously injected atropine decreased the total enthalpy and that of water vapour, while nasal administration of oximetazoline also decreased the total enthalpy. Nasal administration of homatropine or pilocarpine had no effect on the air conditioning. In comparison with normal subjects, those with vasomotor rhinitis had an increased enthalpy of the air, while the same enthalpy factor was reduced in cases with atrophic rhinitis. Laryngectomized patients had no significant difference in the air conditioning capacity of the nose in relation to normal subjects, while patients operated with partial maxillectomy had a considerable reduction in vaporization and total enthalpy.

Why Animals Run on Legs, Not on Wheels.

ERIC Educational Resources Information Center

Diamond, Jared

1983-01-01

Speculates why animals have not developed wheels in place of inefficient legs. One study cited suggests three reasons why animals are better off without wheels: wheels are efficient only on hard surfaces, limitation of wheeled motion due to vertical obstructions, and the problem of turning in spaces cluttered with obstacles. (JN)

The Fatigue Life Prediction of Train Wheel Rims Containing Spherical Inclusions

NASA Astrophysics Data System (ADS)

Li, Yajie; Chen, Huanguo; Cai, Li; Chen, Pei; Qian, Jiacheng; Wu, Jianwei

2018-03-01

It is a common phenomenon that fatigue crack initiation occurs frequently in the inclusions of wheel rims. Research on the fatigue life of wheel rims with spherical inclusions is of great significance on the reliability of wheels. To find the danger point and working condition of a wheel, the stress state of the wheel rim with spherical inclusions was analyzed using the finite element method. Results revealed that curve conditions are dangerous. The critical plane method, based on the cumulative fatigue damage theory, was used to predict the fatigue life of the wheel rim and whether it contained spherical inclusions or not under curve conditions. It was found that the fatigue life of the wheel rim is significantly shorter when the wheel rim contains spherical inclusions. Analysis of the results can provide a theoretical basis and technical support for train operations and maintenance.

Propulsion Wheel Motor for an Electric Vehicle

NASA Technical Reports Server (NTRS)

Herrera, Eduardo (Inventor); Farrell, Logan Christopher (Inventor); Guo, Raymond (Inventor); Junkin, Lucien Q. (Inventor); Bluethmann, William J. (Inventor); Vitale, Robert L. (Inventor); Weber, Steven J. (Inventor); Lee, Chunhao J. (Inventor); Eggleston, IV, Raymond Edward (Inventor); Figuered, Joshua M. (Inventor);

Suspension system for a wheel rolling on a flat track. [bearings for directional antennas

NASA Technical Reports Server (NTRS)

Mcginness, H. D. (Inventor)

1981-01-01

An improved suspension system for an uncrowned wheel rolling on a flat track is presented. It is characterized by a wheel frame assembly including a wheel frame and at least one uncrowned wheel connected in supporting relation with the frame. It is adapted to be seated in rolling engagement with a flat track, a load supporting bed, and a plurality of flexural struts interconnecting the bed in supported relation with the frame. Each of said struts is disposed in a plane passing through the center of the uncrowned wheel surface along a line substantially bisecting the line of contact established between the wheel surface and the flat surface of the truck and characterized by a modulus of elasticity sufficient for maintaining the axis of rotation for the wheel in substantial parallelism with the line of contact established between the surfaces of the wheel and track.

Peculiarities of Clutch Forming Rails and Wheel Block Construction

NASA Astrophysics Data System (ADS)

Shiler, V. V.; Galiev, I. I.; Shiler, A. V.

2018-03-01

The clutch of the wheel and rail is significantly influenced by the design features of the standard wheel pair, which are manifested in the presence of "parasitic" slipping of the wheels along the rails during its movement. The purpose of the presented work is to evaluate new design solutions for wheel sets. The research was carried out using methods of comparative simulation modelling and physical prototyping. A new design of the wheel pair (block wheel pair) is proposed, which features an independent rotation of all surfaces of the wheels in contact with the rails. The block construction of the wheel pair forms open mechanical contours with the track gauge, which completely eliminates the "parasitic" slippage. As a result, in the process of implementing traction or braking forces, the coupling coefficient of the block construction of the wheel pair is significantly higher than that of existing structures. In addition, in the run-out mode, the resistance to movement of the block wheel pair is half as much. All this will allow one to significantly reduce the energy consumption for traction of trains, wear of track elements and crew, and to increase the speed and safety of train traffic.

Method for controlling a vehicle with two or more independently steered wheels

DOEpatents

Reister, D.B.; Unseren, M.A.

1995-03-28

A method is described for independently controlling each steerable drive wheel of a vehicle with two or more such wheels. An instantaneous center of rotation target and a tangential velocity target are inputs to a wheel target system which sends the velocity target and a steering angle target for each drive wheel to a pseudo-velocity target system. The pseudo-velocity target system determines a pseudo-velocity target which is compared to a current pseudo-velocity to determine a pseudo-velocity error. The steering angle targets and the steering angles are inputs to a steering angle control system which outputs to the steering angle encoders, which measure the steering angles. The pseudo-velocity error, the rate of change of the pseudo-velocity error, and the wheel slip between each pair of drive wheels are used to calculate intermediate control variables which, along with the steering angle targets are used to calculate the torque to be applied at each wheel. The current distance traveled for each wheel is then calculated. The current wheel velocities and steering angle targets are used to calculate the cumulative and instantaneous wheel slip and the current pseudo-velocity. 6 figures.

Body weight manipulation, reinforcement value and choice between sucrose and wheel running: a behavioral economic analysis.

PubMed

Belke, Terry W; Pierce, W David

2009-02-01

Twelve female Long-Evans rats were exposed to concurrent variable (VR) ratio schedules of sucrose and wheel-running reinforcement (Sucrose VR 10 Wheel VR 10; Sucrose VR 5 Wheel VR 20; Sucrose VR 20 Wheel VR 5) with predetermined budgets (number of responses). The allocation of lever pressing to the sucrose and wheel-running alternatives was assessed at high and low body weights. Results showed that wheel-running rate and lever-pressing rates for sucrose and wheel running increased, but the choice of wheel running decreased at the low body weight. A regression analysis of relative consumption as a function of relative price showed that consumption shifted toward sucrose and interacted with price differences in a manner consistent with increased substitutability. Demand curves showed that demand for sucrose became less elastic while demand for wheel running became more elastic at the low body weight. These findings reflect an increase in the difference in relative value of sucrose and wheel running as body weight decreased. Discussion focuses on the limitations of response rates as measures of reinforcement value. In addition, we address the commonalities between matching and demand curve equations for the analysis of changes in relative reinforcement value.

Measurements of characteristic parameters of extremely small cogged wheels with low module by means of low-coherence interferometry

NASA Astrophysics Data System (ADS)

Pakula, Anna; Tomczewski, Slawomir; Skalski, Andrzej; Biało, Dionizy; Salbut, Leszek

2010-05-01

This paper presents novel application of Low Coherence Interferometry (LCI) in measurements of characteristic parameters as circular pitch, foot diameter, heads diameter, in extremely small cogged wheels (cogged wheel diameter lower than θ=3 mm and module m = 0.15) produced from metal and ceramics. The most interesting issue concerning small diameter cogged wheels occurs during their production. The characteristic parameters of the wheel depend strongly on the manufacturing process and while inspecting small diameter wheels the shrinkage during the cast varies with the slight change of fabrication process. In the paper the LCI interferometric Twyman - Green setup with pigtailed high power light emitting diode, for cogged wheels measurement, is described. Due to its relatively big field of view the whole wheel can be examined in one measurement, without the necessity of numerical stitching. For purposes of small cogged wheel's characteristic parameters measurement the special binarization algorithm was developed and successfully applied. At the end the results of measurement of heads and foot diameters of two cogged wheels obtained by proposed LCI setup are presented and compared with the results obtained by the commercial optical profiler. The results of examination of injection moulds used for fabrication of measured cogged wheels are also presented. Additionally, the value of cogged wheels shrinkage is calculated as a conclusion for obtained results. Proposed method is suitable for complex measurements of small diameter cogged wheels with low module especially when there are no measurements standards for such objects.

Exercise to reduce the escalation of cocaine self-administration in adolescent and adult rats.

PubMed

Zlebnik, Natalie E; Anker, Justin J; Carroll, Marilyn E

2012-12-01

Concurrent access to an exercise wheel decreases cocaine self-administration under short access (5 h/day for 5 days) conditions and suppresses cocaine-primed reinstatement in adult rats. The effect of exercise (wheel running) on the escalation of cocaine intake during long access (LgA, 6 h/day for 26 days) conditions was evaluated. Adolescent and adult female rats acquired wheel running, and behavior was allowed to stabilize for 3 days. They were then implanted with an iv catheter and allowed to self-administer cocaine (0.4 mg/kg, iv) during 6-h daily sessions for 16 days with concurrent access to either an unlocked or a locked running wheel. Subsequently, for ten additional sessions, wheel access conditions during cocaine self-administration sessions were reversed (i.e., locked wheels became unlocked and vice versa). In the adolescents, concurrent access to the unlocked exercise wheel decreased responding for cocaine and attenuated escalation of cocaine intake irrespective of whether the locked or unlocked condition came first. However, cocaine intake increased when the wheel was subsequently locked for the adolescents that had initial access to an unlocked wheel. Concurrent wheel access either before or after the locked wheel access did not reduce cocaine intake in adults. Wheel running reduced cocaine intake during LgA conditions in adolescent but not adult rats, and concurrent access to the running wheel was necessary. These results suggest that exercise prevents cocaine seeking and that this effect is more pronounced in adolescents than adults.

Temperature dependences of saturated vapor pressure and the enthalpy of vaporization of n-pentyl esters of dicarboxylic acids

NASA Astrophysics Data System (ADS)

Portnova, S. V.; Krasnykh, E. L.; Levanova, S. V.

2016-05-01

The saturated vapor pressures and enthalpies of vaporization of n-pentyl esters of linear C2-C6 dicarboxylic acids are determined by the transpiration method in the temperature range of 309.2-361.2 K. The dependences of enthalpies of vaporization on the number of carbon atoms in the molecule and on the retention indices have been determined. The predictive capabilities of the existing calculation schemes for estimation of enthalpy of vaporization of the studied compounds have been analyzed.

Insights on activation enthalpy for non-Schmid slip in body-centered cubic metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hale, Lucas M.; Lim, Hojun; Zimmerman, Jonathan A.

2014-12-18

We use insights gained from atomistic simulation to develop an activation enthalpy model for dislocation slip in body-centered cubic iron. Furthermore, using a classical potential that predicts dislocation core stabilities consistent with ab initio predictions, we quantify the non-Schmid stress-dependent effects of slip. The kink-pair activation enthalpy is evaluated and a model is identified as a function of the general stress state. Thus, our model enlarges the applicability of the classic Kocks activation enthalpy model to materials with non-Schmid behavior.

Enthalpies of solvation for dopamine hydrochloride in water-ethanol solutions

NASA Astrophysics Data System (ADS)

Vandyshev, V. N.; Ledenkov, S. F.; Molchanov, A. S.

2012-10-01

The enthalpies of dissolution of dopamine hydrochloride (H2Dop · HCl) in water-ethanol solvents containing from 0 to 0.8 mole fraction of ethanol are measured by calorimetry at 298.15 K. Standard enthalpies of transfer (Δtr H ∘) for the molecular (H2Dop) and cationic (H3Dop+) forms of dopamine from water into binary solvents are calculated from the obtained data. The enthalpies of transfer of H3Dop+ cation are determined from the enthalpies of dissolution of H2Dop · HCl using the familiar method of separating the molar quantities into ionic contributions (Ph4P+ = BPh{4/-}), and by an original alternative procedure. The effect of the composition of the binary solvent on the solvation of dopamine is considered.

Enthalpy of mixing of liquid Co–Sn alloys

PubMed Central

Yakymovych, A.; Fürtauer, S.; Elmahfoudi, A.; Ipser, H.; Flandorfer, H.

2014-01-01

A literature overview of enthalpy of mixing data for liquid Co–Sn alloys shows large scattering but no clear temperature dependence. Therefore drop calorimetry was performed in the Co–Sn system at twelve different temperatures in 100 K steps in the temperature range (673 to 1773) K. The integral enthalpy of mixing was determined starting from 1173 K and fitted to a standard Redlich–Kister polynomial. In addition, the limiting partial molar enthalpy of Co in Sn was investigated by small additions of Co to liquid Sn at temperatures (673 to 1773) K. The integral and partial molar enthalpies of the Co–Sn system generally show an exothermic mixing behavior. Significant temperature dependence was detected for the enthalpies of mixing. The minimum integral enthalpy values vary with rising temperature from approx. −7820 J/mol at T = 1173 K to −1350 J/mol at T = 1773 K; the position of the minimum is between (59 and 61) at.% Co. The results are discussed and compared with literature data available for this system. X-ray studies and scanning electron microscopy of selected alloys obtained from the calorimetric measurements were carried out in order to check the completeness of the solution process. PMID:24994940

Enthalpy generation from mixing in hohlraum-driven targets

NASA Astrophysics Data System (ADS)

Amendt, Peter; Milovich, Jose

2016-10-01

The increase in enthalpy from the physical mixing of two initially separated materials is analytically estimated and applied to ICF implosions and gas-filled hohlraums. Pressure and temperature gradients across a classical interface are shown to be the origin of enthalpy generation from mixing. The amount of enthalpy generation is estimated to be on the order of 100 Joules for a 10 micron-scale annular mixing layer between the solid deuterium-tritium fuel and the undoped high-density carbon ablator of a NIF-scale implosion. A potential resonance is found between the mixing layer thickness and gravitational (Cs2/ g) and temperature-gradient scale lengths, leading to elevated enthalpy generation. These results suggest that if mixing occurs in current capsule designs for the National Ignition Facility, the ignition margin may be appreciably eroded by the associated enthalpy of mixing. The degree of enthalpy generation from mixing of high- Z hohlraum wall material and low- Z gas fills is estimated to be on the order of 100 kJ or more for recent NIF-scale hohlraum experiments, which is consistent with the inferred missing energy based on observed delays in capsule implosion times. Work performed under the auspices of Lawrence Livermore National Security, LLC (LLNS) under Contract No. DE-AC52-07NA27344.

Wheeled and Tracked Vehicle Endurance Testing

DTIC Science & Technology

2014-10-02

Vehicle (ATV) 10 10 50 30 Fire Trucks - Crash and Rescue, Brush, Structural 49/56/50 22/16/50 - 29/28/0 a Wheeled Combat 30 40 15 15 Roboticb - 30 50... Wheeled Light W-M = Wheeled Medium W-H = Wheeled Heavy LM-TT = Light/Medium Truck H-TT = Heavy Truck Tractor/Trailer M = Motorcycle FT = Fire ...TYPE Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Test Operations Procedure (TOP) 02-2-506A Wheeled and Tracked Vehicle Endurance

Leg pairs as virtual wheels

NASA Astrophysics Data System (ADS)

Howe, Russel; Duttweiler, Mark; Khanlian, Luke; Setrakian, Mark

2005-05-01

We propose the use of virtual wheels as the starting point of a new vehicle design. Each virtual wheel incorporates a pair of simple legs that, by simulating the rotary motion and ground contact of a traditional wheel, combine many of the benefits of legged and wheeled motion. We describe the use of virtual wheels in the design of a robotic mule, presenting an analysis of the mule's mobility the results of our efforts to model and build such a device.

Investigation of diamond wheel topography in Elliptical Ultrasonic Assisted Grinding (EUAG) of monocrystal sapphire using fractal analysis method.

PubMed

Wang, Qiuyan; Zhao, Wenxiang; Liang, Zhiqiang; Wang, Xibin; Zhou, Tianfeng; Wu, Yongbo; Jiao, Li

2018-03-01

The wear behaviors of grinding wheel have significant influence on the work-surface topography. However, a comprehensive and quantitative method is lacking for evaluating the wear conditions of grinding wheel. In this paper, a fractal analysis method is used to investigate the wear behavior of resin-bonded diamond wheel in Elliptical Ultrasonic Assisted Grinding (EUAG) of monocrystal sapphire, and a series of experiments on EUAG and conventional grinding (CG) are performed. The results show that the fractal dimension of grinding wheel topography is highly correlated to the wear behavior, i.e., grain fracture, grain pullout, and wheel loading. An increase in cutting edge density on the wheel surface results in an increase of the fractal dimension, but an increase in the grain pullout and wheel loading results in a decrease in the fractal dimension. The wheel topography in EUAG has a higher fractal dimension than that in CG before 60 passes due to better self-sharpening behavior, and then has a smaller fractal dimension because of more serious wheel loadings after 60 passes. By angle-dependent distribution analysis of profile fractal dimensions, the wheel surface topography is transformed from isotropic to anisotropic. These indicated that the fractal analysis method could be further used in monitoring of a grinding wheel performance in EUAG. Copyright © 2017 Elsevier B.V. All rights reserved.

14 CFR 23.479 - Level landing conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... attitudes: (1) For airplanes with tail wheels, a normal level flight attitude. (2) For airplanes with nose wheels, attitudes in which— (i) The nose and main wheels contact the ground simultaneously; and (ii) The main wheels contact the ground and the nose wheel is just clear of the ground. The attitude used in...

Curve squeal of urban rolling stock—Part 1: State of the art and field measurements

NASA Astrophysics Data System (ADS)

Vincent, N.; Koch, J. R.; Chollet, H.; Guerder, J. Y.

2006-06-01

This is the first part of a series of three papers dealing with curve squeal of urban rolling stock such as metros and trams. After a brief review of the present state of the art, the key parameters involved in curve squeal generation are discussed. Then, some results of field measurement campaigns, on metro and on tramway systems, are presented. A specific measurement methodology is applied for both campaigns in order to record the main key parameters: rolling speed, axle angle of attack, wheel/rail lateral position and modal damping of relevant wheel modes. On-board microphones are mounted close to each wheel of the instrumented bogies in order to locate the squealing wheels. No squeal occurs on the outer wheel of the leading axle in flange contact with the rail. The highest squeal levels are generally found on the front inner wheel. Pure tone frequencies are related to wheel axial modes for metro (undamped steel wheel) and for tramway (resilient wheels). Squeal occurrence is also observed on a bogie with independent wheels.

Sensor set-up for wireless measurement of automotive rim and wheel parameters in laboratory conditions

NASA Astrophysics Data System (ADS)

Borecki, M.; Prus, P.; Korwin-Pawlowski, M. L.; Rychlik, A.; Kozubel, W.

2017-08-01

Modern rims and wheels are tested at the design and production stages. Tests can be performed in laboratory conditions and on the ride. In the laboratory, complex and costly equipment is used, as for example wheel balancers and impact testers. Modern wheel balancers are equipped with electronic and electro-mechanical units that enable touch-less measurement of dimensions, including precision measurement of radial and lateral wheel run-out, automatic positioning and application of the counterweights, and vehicle wheel set monitoring - tread wear, drift angles and run-out unbalance. Those tests are performed by on-wheel axis measurements with laser distance meters. The impact tester enables dropping of weights from a defined height onto a wheel. Test criteria are the loss of pressure of the tire and generation of cracks in the wheel without direct impact of the falling weights. In the present paper, a set up composed of three accelerometers, a temperature sensor and a pressure sensor is examined as the base of a wheel tester. The sensor set-up configuration, on-line diagnostic and signal transmission are discussed.

Nocturnal to Diurnal Switches with Spontaneous Suppression of Wheel-Running Behavior in a Subterranean Rodent

PubMed Central

Tachinardi, Patricia; Tøien, Øivind; Valentinuzzi, Veronica S.; Buck, C. Loren; Oda, Gisele A.

2015-01-01

Several rodent species that are diurnal in the field become nocturnal in the lab. It has been suggested that the use of running-wheels in the lab might contribute to this timing switch. This proposition is based on studies that indicate feed-back of vigorous wheel-running on the period and phase of circadian clocks that time daily activity rhythms. Tuco-tucos (Ctenomys aff. knighti) are subterranean rodents that are diurnal in the field but are robustly nocturnal in laboratory, with or without access to running wheels. We assessed their energy metabolism by continuously and simultaneously monitoring rates of oxygen consumption, body temperature, general motor and wheel running activity for several days in the presence and absence of wheels. Surprisingly, some individuals spontaneously suppressed running-wheel activity and switched to diurnality in the respirometry chamber, whereas the remaining animals continued to be nocturnal even after wheel removal. This is the first report of timing switches that occur with spontaneous wheel-running suppression and which are not replicated by removal of the wheel. PMID:26460828

Analysis and control on changeable wheel tool system of hybrid grinding and polishing machine tool for blade finishing

NASA Astrophysics Data System (ADS)

He, Qiuwei; Lv, Xingming; Wang, Xin; Qu, Xingtian; Zhao, Ji

2017-01-01

Blade is the key component in the energy power equipment of turbine, aircraft engines and so on. Researches on the process and equipment for blade finishing become one of important and difficult point. To control precisely tool system of developed hybrid grinding and polishing machine tool for blade finishing, the tool system with changeable wheel for belt polishing is analyzed in this paper. Firstly, the belt length and wrap angle of each wheel in different position of tension wheel swing angle in the process of changing wheel is analyzed. The reasonable belt length is calculated by using MATLAB, and relationships between wrap angle of each wheel and cylinder expansion amount of contact wheel are obtained. Then, the control system for changeable wheel tool structure is developed. Lastly, the surface roughness of blade finishing is verified by experiments. Theoretical analysis and experimental results show that reasonable belt length and wheel wrap angle can be obtained by proposed analysis method, the changeable wheel tool system can be controlled precisely, and the surface roughness of blade after grinding meets the design requirements.

The vibration behavior of railway track at high frequencies under multiple preloads and wheel interactions

PubMed

Wu; Thompson

2000-09-01

The track foundation is preloaded by multiple wheel loads due to the train weight and, as the pad and ballast are nonlinear, their stiffness depends upon the preload in them. Due to the influence of these resilient components of the track, the track vibration is affected by the wheel loads. It is also affected by the wheel/rail interactions. In this article the preloads in the pad and ballast are calculated by considering the nonlinear properties of the track foundation, and thus the preloaded pad and ballast stiffnesses are determined. The vibration properties are explored for the track under multiple wheel loads and multiple wheel/rail interactions by comparing the results from different track models with and without these effects. It is found that the point receptance of the track is reduced and the vibration decay rate is enhanced at low frequencies due to the wheel loads. The effects of the wheel/rail interactions are most significant for frequencies 400-2000 Hz. Because of the wheel/rail interactions, the point receptance fluctuates and the vibration decay is enhanced in the regions around the wheels.

Enthalpy effects on hypervelocity boundary layers

NASA Astrophysics Data System (ADS)

Adam, Philippe H.

Shots with air and carbon dioxide were carried out in the T5 shock tunnel at GALCIT to study enthalpy effects on hypervelocity boundary layers. The model tested was a 1-meter long, 5-deg half-angle cone. It was instrumented with 51 chromel-constantan coaxial thermocouples and the surface heat transfer rate was computed to deduce the state of the boundary layer. Transitional boundary layers obtained confirm the stabilizing effect of enthalpy. As the reservoir enthalpy is increased, the transition Reynolds number evaluated at the reference conditions increases. This stabilizing effect is more rapid in gases with lower dissociation energy and it seems to level off when no further dissociation can be achieved. Normalizing the reservoir enthalpy with the edge enthalpy appears to collapse the data for all gases onto a single curve. A similar collapse is obtained when normalizing both the transition location and the reservoir enthalpy with the maximum temperature conditions obtained with BLIMPK, a nonequilibrium boundary layer code. The observation that reference conditions are more appropriate to normalize high enthalpy transition data was taken a step further by comparing the tunnel data with results from a reentry experiment. When the edge conditions are used, the tunnel and flight data are around an order of magnitude apart. This is commonly attributed to high disturbance levels in tunnels that cause the boundary layer to transition early. However, when the reference conditions are used instead, the tunnel and flight data come within striking distance of one another although the trends with enthalpy are reversed. This difference could be due to the cone bending and nose blunting. Experimental laminar heat transfer levels were compared to numerical results obtained with BLIMPK. Results for air indicate that the reactions are probably in nonequilibrium and that the wall is catalytic. The catalycity is seen to yield higher surface heat transfer rates than the noncatalytic and frozen chemistry models. The results for carbon dioxide, however, are inconclusive. This is, perhaps, because of inadequate modeling of the reactions. Experimentally, an anomalous yet repeatable, rise in the laminar heat transfer level can be seen at medium enthalpies in carbon dioxide boundary layers.

Binding the Mammalian High Mobility Group Protein AT-hook 2 to AT-Rich Deoxyoligonucleotides: Enthalpy-Entropy Compensation

PubMed Central

Joynt, Suzanne; Morillo, Victor; Leng, Fenfei

2009-01-01

HMGA2 is a DNA minor-groove binding protein. We previously demonstrated that HMGA2 binds to AT-rich DNA with very high binding affinity where the binding of HMGA2 to poly(dA-dT)2 is enthalpy-driven and to poly(dA)poly(dT) is entropy-driven. This is a typical example of enthalpy-entropy compensation. To further study enthalpy-entropy compensation of HMGA2, we used isothermal-titration-calorimetry to examine the interactions of HMGA2 with two AT-rich DNA hairpins: 5′-CCAAAAAAAAAAAAAAAGCCCCCGCTTTTTTTTTTTTTTTGG-3′ (FL-AT-1) and 5′-CCATATATATATATATAGCCCCCGCTATATATATATATATGG-3′ (FL-AT-2). Surprisingly, we observed an atypical isothermal-titration-calorimetry-binding curve at low-salt aqueous solutions whereby the apparent binding-enthalpy decreased dramatically as the titration approached the end. This unusual behavior can be attributed to the DNA-annealing coupled to the ligand DNA-binding and is eliminated by increasing the salt concentration to ∼200 mM. At this condition, HMGA2 binding to FL-AT-1 is entropy-driven and to FL-AT-2 is enthalpy-driven. Interestingly, the DNA-binding free energies for HMGA2 binding to both hairpins are almost temperature independent; however, the enthalpy-entropy changes are dependent on temperature, which is another aspect of enthalpy-entropy compensation. The heat capacity change for HMGA2 binding to FL-AT-1 and FL-AT-2 are almost identical, indicating that the solvent displacement and charge-charge interaction in the coupled folding/binding processes for both binding reactions are similar. PMID:19450485

The CPA Equation of State and an Activity Coefficient Model for Accurate Molar Enthalpy Calculations of Mixtures with Carbon Dioxide and Water/Brine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myint, P. C.; Hao, Y.; Firoozabadi, A.

2015-03-27

Thermodynamic property calculations of mixtures containing carbon dioxide (CO 2) and water, including brines, are essential in theoretical models of many natural and industrial processes. The properties of greatest practical interest are density, solubility, and enthalpy. Many models for density and solubility calculations have been presented in the literature, but there exists only one study, by Spycher and Pruess, that has compared theoretical molar enthalpy predictions with experimental data [1]. In this report, we recommend two different models for enthalpy calculations: the CPA equation of state by Li and Firoozabadi [2], and the CO 2 activity coefficient model by Duanmore » and Sun [3]. We show that the CPA equation of state, which has been demonstrated to provide good agreement with density and solubility data, also accurately calculates molar enthalpies of pure CO 2, pure water, and both CO 2-rich and aqueous (H 2O-rich) mixtures of the two species. It is applicable to a wider range of conditions than the Spycher and Pruess model. In aqueous sodium chloride (NaCl) mixtures, we show that Duan and Sun’s model yields accurate results for the partial molar enthalpy of CO 2. It can be combined with another model for the brine enthalpy to calculate the molar enthalpy of H 2O-CO 2-NaCl mixtures. We conclude by explaining how the CPA equation of state may be modified to further improve agreement with experiments. This generalized CPA is the basis of our future work on this topic.« less

The Influence of Wheel/Rail Contact Conditions on the Microstructure and Hardness of Railway Wheels

PubMed Central

Davis, Claire

2014-01-01

The susceptibility of railway wheels to wear and rolling contact fatigue damage is influenced by the properties of the wheel material. These are influenced by the steel composition, wheel manufacturing process, and thermal and mechanical loading during operation. The in-service properties therefore vary with depth below the surface and with position across the wheel tread. This paper discusses the stress history at the wheel/rail contact (derived from dynamic simulations) and observed variations in hardness and microstructure. It is shown that the hardness of an “in-service” wheel rim varies significantly, with three distinct effects. The underlying hardness trend with depth can be related to microstructural changes during manufacturing (proeutectoid ferrite fraction and pearlite lamellae spacing). The near-surface layer exhibits plastic flow and microstructural shear, especially in regions which experience high tangential forces when curving, with consequentially higher hardness values. Between 1 mm and 7 mm depth, the wheel/rail contacts cause stresses exceeding the material yield stress, leading to work hardening, without a macroscopic change in microstructure. These changes in material properties through the depth of the wheel rim would tend to increase the likelihood of crack initiation on wheels toward the end of their life. This correlates with observations from several train fleets. PMID:24526883

Study on design of light-weight super-abrasive wheel

NASA Astrophysics Data System (ADS)

Nohara, K.; Yanagihara, K.; Ogawa, M.

2018-01-01

Fixed-abrasive tool, also called a grinding wheel, is produced by furnacing abrasive compound which contains abrasive grains and binding powder such as vitrified materials or resins. Fixed-abrasive tool is installed on spindle of grinding machine. And it is given 1,800-2,000 min-1 of spindle rotation for the usage. The centrifugal fracture of the compound of fixed- abrasive tool is one of the careful respects in designing. In recent years, however, super-abrasive wheel as a fixed-abrasive tool has been developed and applied widely. One of the most characteristic respects is that metal is applied for the body of grinding-wheel. The strength to hold abrasive grain and the rigidity of wheel become stronger than those of general grinding wheel, also the lifespan of fixed-abrasive tool becomes longer. The weight of fixed-abrasive tool, however, becomes heavier. Therefore, when the super-abrasive wheel is used, the power consumption of spindle motor becomes larger. It also becomes difficult for the grinding-wheel to respond to sudden acceleration or deceleration. Thus, in order to reduce power consumption in grinding and to obtain quicker frequency response of super-abrasive wheel, the new wheel design is proposed. The design accomplishes 46% weight reduction. Acceleration that is one second quicker than that of conventional grinding wheel is obtained.

Development and testing of a new system for assessing wheel-running behaviour in rodents.

PubMed

Chomiak, Taylor; Block, Edward W; Brown, Andrew R; Teskey, G Campbell; Hu, Bin

2016-05-05

Wheel running is one of the most widely studied behaviours in laboratory rodents. As a result, improved approaches for the objective monitoring and gathering of more detailed information is increasingly becoming important for evaluating rodent wheel-running behaviour. Here our aim was to develop a new quantitative wheel-running system that can be used for most typical wheel-running experimental protocols. Here we devise a system that can provide a continuous waveform amenable to real-time integration with a high-speed video ideal for wheel-running experimental protocols. While quantification of wheel running behaviour has typically focused on the number of revolutions per unit time as an end point measure, the approach described here allows for more detailed information like wheel rotation fluidity, directionality, instantaneous velocity, and acceleration, in addition to total number of rotations, and the temporal pattern of wheel-running behaviour to be derived from a single trace. We further tested this system with a running-wheel behavioural paradigm that can be used for investigating the neuronal mechanisms of procedural learning and postural stability, and discuss other potentially useful applications. This system and its ability to evaluate multiple wheel-running parameters may become a useful tool for screening new potentially important therapeutic compounds related to many neurological conditions.

Phase Transition Enthalpy Measurements of Organic and Organometallic Compounds and Ionic Liquids. Sublimation, Vaporization, and Fusion Enthalpies from 1880 to 2015. Part 2. C11-C192

NASA Astrophysics Data System (ADS)

Acree, William; Chickos, James S.

2017-03-01

The second part of this compendium concludes with a collection of phase change enthalpies of organic molecules inclusive of C11-C192 reported over the period 1880-2015. Also included are phase change enthalpies including fusion, vaporization, and sublimation enthalpies for organometallic, ionic liquids, and a few inorganic compounds. Paper I of this compendium, published separately, includes organic compounds from C1 to C10 and describes a group additivity method for evaluating solid, liquid, and gas phase heat capacities as well as temperature adjustments of phase changes. Paper II of this compendium also includes an updated version of a group additivity method for evaluating total phase change entropies which together with the fusion temperature can be useful in estimating total phase change enthalpies. Other uses include application in identifying potential substances that either form liquid or plastic crystals or exhibit additional phase changes such as undetected solid-solid transitions or behave anisotropically in the liquid state.

Radon and ammonia transects across the Cerro Prieto geothermal field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Semprini, L.; Kruger, P.

1981-01-01

Radon and ammonia transects, conducted at the Cerro Prieto geothermal field, involve measurement of concentration gradients at wells along lines of structural significance in the reservoir. Analysis of four transects showed radon concentrations ranging from 0.20 to 3.60 nCi/kg and ammonia concentrations from 17.6 to 59.3 mg/l. The data showed the lower concentrations in wells of lowest enthalpy fluid and the higher concentrations in wells of highest enthalpy fluid. Linear correlation analysis of the radon-enthalpy data indicated a strong relationship, with a marked influence by the two-phase conditions of the produced fluid. It appears that after phase separation in themore » reservoir, radon achieves radioactive equilibrium between fluid and rock, suggesting that the phase separation occurs well within the reservoir. A two-phase mixing model based on radon-enthalpy relations allows estimation of the fluid phase temperatures in the reservoir. Correlations of ammonia concentration with fluid enthalpy suggests an equilibrium partitioning model in which enrichment of ammonia correlates with higher enthalpy vapor.« less

Making sense of enthalpy of vaporization trends for ionic liquids: new experimental and simulation data show a simple linear relationship and help reconcile previous data.

PubMed

Verevkin, Sergey P; Zaitsau, Dzmitry H; Emel'yanenko, Vladimir N; Yermalayeu, Andrei V; Schick, Christoph; Liu, Hongjun; Maginn, Edward J; Bulut, Safak; Krossing, Ingo; Kalb, Roland

2013-05-30

Vaporization enthalpy of an ionic liquid (IL) is a key physical property for applications of ILs as thermofluids and also is useful in developing liquid state theories and validating intermolecular potential functions used in molecular modeling of these liquids. Compilation of the data for a homologous series of 1-alkyl-3-methylimidazolium bis(trifluoromethane-sulfonyl)imide ([C(n)mim][NTf2]) ILs has revealed an embarrassing disarray of literature results. New experimental data, based on the concurring results from quartz crystal microbalance, thermogravimetric analyses, and molecular dynamics simulation have revealed a clear linear dependence of IL vaporization enthalpies on the chain length of the alkyl group on the cation. Ambiguity of the procedure for extrapolation of vaporization enthalpies to the reference temperature 298 K was found to be a major source of the discrepancies among previous data sets. Two simple methods for temperature adjustment of vaporization enthalpies have been suggested. Resulting vaporization enthalpies obey group additivity, although the values of the additivity parameters for ILs are different from those for molecular compounds.

77 FR 52682 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-30

... OTR Wheel Engineering, Inc.'s Wheel Hub Assemblies and TRBs,'' dated February 7, 2011 (finding Blackstone OTR LLC and OTR Wheel Engineering, Inc.'s wheel hub assemblies are within the scope of the order... Trend Engineering Ltd.'s Wheel Hub Assemblies,'' dated April 18, 2011 (finding New Trend Engineering...

49 CFR 229.75 - Wheels and tire defects.

Code of Federal Regulations, 2010 CFR

2010-10-01

... crack or break in the flange, tread, rim, plate, or hub. (l) A loose wheel or tire. (m) Fusion welding... 49 Transportation 4 2010-10-01 2010-10-01 false Wheels and tire defects. 229.75 Section 229.75....75 Wheels and tire defects. Wheels and tires may not have any of the following conditions: (a) A...

49 CFR 229.75 - Wheels and tire defects.

Code of Federal Regulations, 2012 CFR

2012-10-01

... crack or break in the flange, tread, rim, plate, or hub. (l) A loose wheel or tire. (m) Fusion welding... 49 Transportation 4 2012-10-01 2012-10-01 false Wheels and tire defects. 229.75 Section 229.75....75 Wheels and tire defects. Wheels and tires may not have any of the following conditions: (a) A...

49 CFR 229.75 - Wheels and tire defects.

Code of Federal Regulations, 2011 CFR

2011-10-01

... crack or break in the flange, tread, rim, plate, or hub. (l) A loose wheel or tire. (m) Fusion welding... 49 Transportation 4 2011-10-01 2011-10-01 false Wheels and tire defects. 229.75 Section 229.75....75 Wheels and tire defects. Wheels and tires may not have any of the following conditions: (a) A...

49 CFR 229.75 - Wheels and tire defects.

Code of Federal Regulations, 2014 CFR

2014-10-01

... crack or break in the flange, tread, rim, plate, or hub. (l) A loose wheel or tire. (m) Fusion welding... 49 Transportation 4 2014-10-01 2014-10-01 false Wheels and tire defects. 229.75 Section 229.75....75 Wheels and tire defects. Wheels and tires may not have any of the following conditions: (a) A...

49 CFR 229.75 - Wheels and tire defects.

Code of Federal Regulations, 2013 CFR

2013-10-01

... crack or break in the flange, tread, rim, plate, or hub. (l) A loose wheel or tire. (m) Fusion welding... 49 Transportation 4 2013-10-01 2013-10-01 false Wheels and tire defects. 229.75 Section 229.75....75 Wheels and tire defects. Wheels and tires may not have any of the following conditions: (a) A...

49 CFR 571.129 - Standard No. 129; New non-pneumatic tires for passenger cars.

Code of Federal Regulations, 2013 CFR

2013-10-01

...-pneumatic tire assembly incorporates a wheel, supports the tire, and attaches, either integrally or... directly or through a wheel or wheel center member, the vertical load and tractive forces from the roadway... assembly means a non-pneumatic tire, alone or in combination with a wheel or wheel center member, which can...

Research on Walking Wheel Slippage Control of Live Inspection Robot

NASA Astrophysics Data System (ADS)

Yan, Yu; Liu, Xiaqing; Guo, Hao; Li, Jinliang; Liu, Lanlan

2017-07-01

To solve the problem of walking wheel slippage of a live inspection robot during walking or climbing, this paper analyzes the climbing capacity of the robot with a statics method, designs a pressing wheel mechanism, and presents a method of indirectly identifying walking wheel slippage by reading speed of the pressing wheel due to the fact that the linear speed of the pressing wheel and the walking wheel at the contract point is the same; and finds that the slippage state can not be controlled through accurate mathematical models after identifying the slippage state, whereas slippage can be controlled with fuzzy control. The experiment results indicate that due to design of the pressing wheel mechanism, friction force of the walking wheel is increased, and the climbing capability of the robot is improved. Within the range of climbing capability of the robot, gradient is the key factor that has influence on slippage of robot, and slippage can be effectively eliminated through the fuzzy control method proposed in this paper.

Magnetic power conversion with machines containing full or porous wheel heat exchangers

NASA Astrophysics Data System (ADS)

Egolf, Peter W.; Kitanovski, Andrej; Diebold, Marc; Gonin, Cyrill; Vuarnoz, Didier

2009-04-01

A first part of the article contains a thermodynamic theory describing the temperature distribution in a Curie wheel. The occurring nonlinear ordinary differential equation has an analytical solution. If a Curie wheel is stabilized by levitation, it is named Palmy wheel. These wheels show a full structure, and because of this reason, their uptake of heat from a flame (Curie wheel) or by (solar) light absorption (Palmy wheel) only on the periphery of a cylinder is very limited. To improve the method, a modification of the principle by introducing a convective heat transport into a porous wheel is discussed. By this the power conversion rate from a heat flux to mechanical and electric power is very much increased. The second part of the article presents results of a theoretical/numerical study on the efficiencies of magnetic power conversion plants operating with porous wheels. Furthermore, these efficiencies—which are promising—are compared with those of existing power conversion plants, as e.g. geothermal binary cycle power plants.

Influence of polygonal wear of railway wheels on the wheel set axle stress

NASA Astrophysics Data System (ADS)

Wu, Xingwen; Chi, Maoru; Wu, Pingbo

2015-11-01

The coupled vehicle/track dynamic model with the flexible wheel set was developed to investigate the effects of polygonal wear on the dynamic stresses of the wheel set axle. In the model, the railway vehicle was modelled by the rigid multibody dynamics. The wheel set was established by the finite element method to analyse the high-frequency oscillation and dynamic stress of wheel set axle induced by the polygonal wear based on the modal stress recovery method. The slab track model was taken into account in which the rail was described by the Timoshenko beam and the three-dimensional solid finite element was employed to establish the concrete slab. Furthermore, the modal superposition method was adopted to calculate the dynamic response of the track. The wheel/rail normal forces and the tangent forces were, respectively, determined by the Hertz nonlinear contact theory and the Shen-Hedrick-Elkins model. Using the coupled vehicle/track dynamic model, the dynamic stresses of wheel set axle with consideration of the ideal polygonal wear and measured polygonal wear were investigated. The results show that the amplitude of wheel/rail normal forces and the dynamic stress of wheel set axle increase as the vehicle speeds rise. Moreover, the impact loads induced by the polygonal wear could excite the resonance of wheel set axle. In the resonance region, the amplitude of the dynamic stress for the wheel set axle would increase considerably comparing with the normal conditions.

A method for improved accuracy in three dimensions for determining wheel/rail contact points

NASA Astrophysics Data System (ADS)

Yang, Xinwen; Gu, Shaojie; Zhou, Shunhua; Zhou, Yu; Lian, Songliang

2015-11-01

Searching for the contact points between wheels and rails is important because these points represent the points of exerted contact forces. In order to obtain an accurate contact point and an in-depth description of the wheel/rail contact behaviours on a curved track or in a turnout, a method with improved accuracy in three dimensions is proposed to determine the contact points and the contact patches between the wheel and the rail when considering the effect of the yaw angle and the roll angle on the motion of the wheel set. The proposed method, with no need of the curve fitting of the wheel and rail profiles, can accurately, directly, and comprehensively determine the contact interface distances between the wheel and the rail. The range iteration algorithm is used to improve the computation efficiency and reduce the calculation required. The present computation method is applied for the analysis of the contact of rails of CHINA (CHN) 75 kg/m and wheel sets of wearing type tread of China's freight cars. In addition, it can be proved that the results of the proposed method are consistent with that of Kalker's program CONTACT, and the maximum deviation from the wheel/rail contact patch area of this two methods is approximately 5%. The proposed method, can also be used to investigate static wheel/rail contact. Some wheel/rail contact points and contact patch distributions are discussed and assessed, wheel and rail non-worn and worn profiles included.

Predicting the enthalpies of melting and vaporization for pure components

NASA Astrophysics Data System (ADS)

Esina, Z. N.; Korchuganova, M. R.

2014-12-01

A mathematical model of the melting and vaporization enthalpies of organic components based on the theory of thermodynamic similarity is proposed. In this empirical model, the phase transition enthalpy for the homological series of n-alkanes, carboxylic acids, n-alcohols, glycols, and glycol ethers is presented as a function of the molecular mass, the number of carbon atoms in a molecule, and the normal transition temperature. The model also uses a critical or triple point temperature. It is shown that the results from predicting the melting and vaporization enthalpies enable the calculation of binary phase diagrams.

Split-step eigenvector-following technique for exploring enthalpy landscapes at absolute zero.

PubMed

Mauro, John C; Loucks, Roger J; Balakrishnan, Jitendra

2006-03-16

The mapping of enthalpy landscapes is complicated by the coupling of particle position and volume coordinates. To address this issue, we have developed a new split-step eigenvector-following technique for locating minima and transition points in an enthalpy landscape at absolute zero. Each iteration is split into two steps in order to independently vary system volume and relative atomic coordinates. A separate Lagrange multiplier is used for each eigendirection in order to provide maximum flexibility in determining step sizes. This technique will be useful for mapping the enthalpy landscapes of bulk systems such as supercooled liquids and glasses.

Enthalpy of phase transitions of lactams

NASA Astrophysics Data System (ADS)

Emel'yanenko, V. N.; Verevkin, S. P.; Ralys, R. V.; Turovtsev, V. V.; Orlov, V. Yu.

2012-10-01

The transpiration method is used to measure the temperature dependences of the vapors pressures of azacyclobutan-2-one (I, CAS 930-21-2) azacyclohexan-2-one (II, CAS 675-20-7); azacyclooctan-2-one (III, CAS 673-66-5); azacyclononan-2-one (IV, CAS 935-30-8) and azacyclotridecan-2-one (V, CAS 947-04-6). Enthalpies of sublimation and vaporisation are determined. The temperatures and enthalpies of fusion of compounds (I, III-V) are found by means of differential scanning calorimetry. The dependences of the enthalpies of vaporisation of lactones, lactams, cycloalkanes, cycloalkanones on the size of a cycle are analyzed.

Portrait of an Aging Wheel

NASA Technical Reports Server (NTRS)

2004-01-01

This plot maps the increasing amounts of energy needed to spin Spirit's right front wheel drive, which has been showing signs of age. The wheel has now traveled six times farther than its design life. Since Spirit's 126th day on Mars, this wheel has required additional electric current to run at normal speeds, as indicated with blue diamonds on this graph. Efforts to improve the situation by redistributing the lubricant in the wheel with heat and rest were only mildly successful (pink squares). To cope with the condition, rover planners have come up with a creative solution: they will drive the rover backwards using five of six wheels. The sixth wheel will be activated only when the terrain demands it.

A simulation model for risk assessment of turbine wheels

NASA Technical Reports Server (NTRS)

Safie, Fayssal M.; Hage, Richard T.

1991-01-01

A simulation model has been successfully developed to evaluate the risk of the Space Shuttle auxiliary power unit (APU) turbine wheels for a specific inspection policy. Besides being an effective tool for risk/reliability evaluation, the simulation model also allows the analyst to study the trade-offs between wheel reliability, wheel life, inspection interval, and rejection crack size. For example, in the APU application, sensitivity analysis results showed that the wheel life limit has the least effect on wheel reliability when compared to the effect of the inspection interval and the rejection crack size. In summary, the simulation model developed represents a flexible tool to predict turbine wheel reliability and study the risk under different inspection policies.

A simulation model for risk assessment of turbine wheels

NASA Astrophysics Data System (ADS)

Safie, Fayssal M.; Hage, Richard T.

A simulation model has been successfully developed to evaluate the risk of the Space Shuttle auxiliary power unit (APU) turbine wheels for a specific inspection policy. Besides being an effective tool for risk/reliability evaluation, the simulation model also allows the analyst to study the trade-offs between wheel reliability, wheel life, inspection interval, and rejection crack size. For example, in the APU application, sensitivity analysis results showed that the wheel life limit has the least effect on wheel reliability when compared to the effect of the inspection interval and the rejection crack size. In summary, the simulation model developed represents a flexible tool to predict turbine wheel reliability and study the risk under different inspection policies.

Resting Is Rusting: A Critical View on Rodent Wheel-Running Behavior.

PubMed

Richter, Sophie Helene; Gass, Peter; Fuss, Johannes

2014-08-01

Physical exercise is known to exert various beneficial effects on brain function and bodily health throughout life. In biomedical research, these effects are widely studied by introducing running wheels into the cages of laboratory rodents. Yet, although rodents start to run in the wheels immediately, and perform wheel-running excessively on a voluntary basis, the biological significance of wheel-running is still not clear. Here, we review the current literature on wheel-running and discuss potentially negative side-effects that may give cause for concern. We particularly emphasize on analogies of wheel-running with stereotypic and addictive behavior to stimulate further research on this topic. © The Author(s) 2014.

Behavioral assessment of intermittent wheel running and individual housing in mice in the laboratory.

PubMed

Pham, Therese M; Brené, Stefan; Baumans, Vera

2005-01-01

Physical cage enrichment--exercise devices for rodents in the laboratory--often includes running wheels. This study compared responses of mice in enriched physical and social conditions and in standard social conditions to wheel running, individual housing, and open-field test. The study divided into 6 groups, 48 female BALB/c mice group housed in enriched and standard conditions. On alternate days, the study exposed 2 groups to individual running wheel cages. It intermittently separated from their cage mates and housed individually 2 groups with no running wheels; 2 control groups remained in enriched or standard condition cages. There were no significant differences between enriched and standard group housed mice in alternate days' wheel running. Over time, enriched, group housed mice ran less. Both groups responded similarly to individual housing. In open-field test, mice exposed to individual housing without running wheel moved more and faster than wheel running and home cage control mice. They have lower body weights than group housed and wheel running mice. Intermittent withdrawal of individual housing affects the animals more than other commodities. Wheel running normalizes some effects of intermittent separation from the enriched, social home cage.

Model Predictive Control considering Reachable Range of Wheels for Leg / Wheel Mobile Robots

NASA Astrophysics Data System (ADS)

Suzuki, Naito; Nonaka, Kenichiro; Sekiguchi, Kazuma

2016-09-01

Obstacle avoidance is one of the important tasks for mobile robots. In this paper, we study obstacle avoidance control for mobile robots equipped with four legs comprised of three DoF SCARA leg/wheel mechanism, which enables the robot to change its shape adapting to environments. Our previous method achieves obstacle avoidance by model predictive control (MPC) considering obstacle size and lateral wheel positions. However, this method does not ensure existence of joint angles which achieves reference wheel positions calculated by MPC. In this study, we propose a model predictive control considering reachable mobile ranges of wheels positions by combining multiple linear constraints, where each reachable mobile range is approximated as a convex trapezoid. Thus, we achieve to formulate a MPC as a quadratic problem with linear constraints for nonlinear problem of longitudinal and lateral wheel position control. By optimization of MPC, the reference wheel positions are calculated, while each joint angle is determined by inverse kinematics. Considering reachable mobile ranges explicitly, the optimal joint angles are calculated, which enables wheels to reach the reference wheel positions. We verify its advantages by comparing the proposed method with the previous method through numerical simulations.

Determination of graphene's edge energy using hexagonal graphene quantum dots and PM7 method.

PubMed

Vorontsov, Alexander V; Tretyakov, Evgeny V

2018-05-18

Graphene quantum dots (GQDs) are important for a variety of applications and designs, and the shapes of GQDs rely on the energy of their boundaries. Presently, many methods have been developed for the preparation of GQDs with the required boundaries, shapes and edge terminations. However, research on the properties of GQDs and their applications is limited due to the unavailability of these compounds in pure form. In the present computational study, the standard enthalpy of formation, the standard enthalpy of formation of edges and the standard enthalpy of hydrogenation are studied for hexagonal GQDs with purely zigzag and armchair edges in non-passivated and H-passivated forms using the semiempirical quantum chemistry method pm7. The standard enthalpy of formation of the edge is found to remain constant for GQDs studied in the range of 1 to 6 nm, and the enthalpies of edge C atoms are 32.4 and 35.5 kcal mol-1 for armchair and zigzag edges, respectively. In contrast to some literature data, the standard enthalpy of formation of hydrogenated edges is far from zero, and the values are 7.3 and 8.0 kcal mol-1 C for armchair and zigzag edges, respectively. The standard enthalpy of hydrogenation is found to be -10.2 and -9.72 eV nm-1 for the armchair and zigzag edges, respectively.

High frequency vibration characteristics of electric wheel system under in-wheel motor torque ripple

NASA Astrophysics Data System (ADS)

Mao, Yu; Zuo, Shuguang; Wu, Xudong; Duan, Xianglei

2017-07-01

With the introduction of in-wheel motor, the electric wheel system encounters new vibration problems brought by motor torque ripple excitation. In order to analyze new vibration characteristics of electric wheel system, torque ripple of in-wheel motor based on motor module and vector control system is primarily analyzed, and frequency/order features of the torque ripple are discussed. Then quarter vehicle-electric wheel system (QV-EWS) dynamics model based on the rigid ring tire assumption is established and the main parameters of the model are identified according to tire free modal test. Modal characteristics of the model are further analyzed. The analysis indicates that torque excitation of in-wheel motor is prone to arouse horizontal vibration, in which in-phase rotational, anti-phase rotational and horizontal translational modes of electric wheel system mainly participate. Based on the model, vibration responses of the QV-EWS under torque ripple are simulated. The results show that unlike vertical low frequency (lower than 20 Hz) vibration excited by road roughness, broadband torque ripple will arouse horizontal high frequency (50-100 Hz) vibration of electric wheel system due to participation of the three aforementioned modes. To verify the theoretical analysis, the bench experiment of electric wheel system is conducted and vibration responses are acquired. The experiment demonstrates the high frequency vibration phenomenon of electric wheel system and the measured order features as well as main resonant frequencies agree with simulation results. Through theoretical modeling, analysis and experiments this paper reveals and explains the high frequency vibration characteristics of electric wheel system, providing references for the dynamic analysis, optimal design of QV-EWS.

Reciprocal inhibitory effects of intravenous d-methamphetamine self-administration and wheel activity in rats

PubMed Central

Miller, ML; Vaillancourt, BD; Wright, MJ; Aarde, SM; Vandewater, SA; Creehan, KM; Taffe, MA

2011-01-01

Background Some epidemiological and cessation studies suggest physical exercise attenuates or prevents recreational drug use in humans. Preclinical studies indicate wheel activity reduces cocaine self-administration in rats; this may, however, require the establishment of compulsive wheel activity. Methods Effects of concurrent wheel activity on intravenous d-methamphetamine (METH) self-administration were examined in male Wistar and Sprague Dawley rats with negligible prior wheel experience. Wistar rats self-administered METH (0.05 mg/kg/inf) under a fixed-ratio 1 (FR1) schedule with concurrent access to an activity wheel during sessions 1–14, 8–21 or 15–21. Control rats which did not self-administer METH had access to an activity wheel during sessions 1–14, 8–21 or 15–28. Sprague Dawley rats self-administered METH (0.1 mg/kg/inf) under FR1 for 14 sessions with either concurrent access to a locked or an unlocked activity wheel. Results METH self-administration was lower when the wheel was available concurrently from the start of self-administration training in both strains, even though Sprague Dawley rats self-administered twice as many METH infusions and ran one-sixth as much on the wheel compared to Wistar rats. Wheel access initiated after 7 or 14 days had no effect on METH self-administration in Wistar rats. Wheel activity was significantly reduced in these groups compared with the group with concurrent wheel and METH access for the first 14 sessions. Conclusions These data show METH self-administration is reduced by exercise if initiated from the start of self-administration and that prior METH self-administration experience interferes with the value of exercise as a reinforcer. PMID:21899959

Enthalpy of Vaporization by Gas Chromatography: A Physical Chemistry Experiment

ERIC Educational Resources Information Center

Ellison, Herbert R.

2005-01-01

An experiment is conducted to measure the enthalpy of vaporization of volatile compounds like methylene chloride, carbon tetrachloride, and others by using gas chromatography. This physical property was measured using a very tiny quantity of sample revealing that it is possible to measure the enthalpies of two or more compounds at the same time.

Enthalpy Costs of Making and Breaking Bonds: A Game of Generating Molecules with Proper Lewis Structures

ERIC Educational Resources Information Center

Bell, Peter T.; Adkins, Alyssa D.; Gamble, Rex J.; Schultz, Linda D.

2009-01-01

"Enthalpy Costs" is a simple card game created to assist students in developing proper Lewis structure drawing skills. Score keeping is accomplished by tracking the enthalpy changes associated with bond-making and bond-breaking processes during formation of molecules represented by proper Lewis structures. Playing the game requires the student to…

PowerWheel - A new look at waterwheels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weisman, R.N.; Broome, K.R.; Mayo, H.A.

1995-12-31

The PowerWheel is an advanced overshot water wheel, designed to generate electric power at drop structures on canals or on overflow spillways. Unlike the wheels of the 18th and 19th century which were designed to have maximum efficiency at a single flow rate, the current applications demand a wheel that can operate efficiently over a wide range of flows. The prototype PowerWheel will have a width to diameter ratio of 3 or more, in contrast to the wheels of the 19th century, which had large diameters and narrow widths. A model PowerWheel was built of plexiglass and delivered for testingmore » to the Imbt Hydraulics Laboratory at Lehigh University. The wheel has a diameter of 3.5 ft and is 16 in wide. The wheel contains 20 buckets and the bucket depth can be varied from a shallow depth of 4 in to a mid depth of 7 in to 10 in for the deep bucket. The blades have a rather simple geometry with a 4 in radius quarter circle at the outside of the wheel and then straight to the bottom of the bucket. The flume in which the wheel was tested has a width of 18 in. A hole was cut in the head box of the flume and a delivery chute was connected to the head box. The position of the chute can readily be moved up or down in relation to the wheel; for a fixed position of the chute on the head box, the slope of the chute can be changed because the chute was attached to the head box with a piano hinge. The laboratory flow system can deliver flow up to 6 cfs through a calibrated Venturi meter. The PowerWheel was subjected to flows ranging from 0.3 to 3.5 cfs.« less

Effects of genetic background and environmental novelty on wheel running as a rewarding behaviour in mice.

PubMed

de Visser, Leonie; van den Bos, Ruud; Stoker, Astrid K; Kas, Martien J H; Spruijt, Berry M

2007-02-27

Recent studies suggest running wheel activity to be naturally rewarding and reinforcing; considering the shared neuro-behavioural characteristics with drug-induced reward situations, wheel running behaviour gains interest as a tool to study mechanisms underlying reward-sensitivity. Previously, we showed that wheel running has the potential to disrupt the daily organization of home cage behaviour in female C57BL/6 [de Visser L, van den Bos R, Spruijt BM. Automated home cage observations as a tool to measure the effects of wheel running on cage floor locomotion. Behav Brain Res 2005;160:382-8]. In the present study, we investigated the effects of novelty-induced stress on wheel running and its impact on home cage behaviour in male C57BL/6 and DBA/2 mice. Our aim was to determine whether wheel running may be used as a tool to study both genetic and environmentally induced differences in sensitivity to rewarding behaviour in mice. One group of male mice was placed in an automated home cage observation system for 2 weeks with a wheel integrated in the cage. A second group of mice was allowed to habituate to this cage for 1 week before a running wheel was introduced. Results showed a pronounced sensitising effect of novelty on the level of wheel running in C57Bl/6 mice but not in DBA mice. Overall levels of wheel running were higher in DBA/2 mice. Furthermore, wheel running affected circadian rhythmicity in DBA/2 mice but not in C57BL/6 mice. From these findings we tentatively suggest that wheel running behaviour could serve as a tool to study the interaction between genetic and environmental factors in sensitivity to rewarding behaviour in mice. As it is displayed spontaneously and easy to monitor, wheel running may be well suitable to be included in high-throughput phenotyping assays.

Wheel-running activity modulates circadian organization and the daily rhythm of eating behavior

PubMed Central

Pendergast, Julie S.; Branecky, Katrina L.; Huang, Roya; Niswender, Kevin D.; Yamazaki, Shin

2014-01-01

Consumption of high-fat diet acutely alters the daily rhythm of eating behavior and circadian organization (the phase relationship between oscillators in central and peripheral tissues) in mice. Voluntary wheel-running activity counteracts the obesogenic effects of high-fat diet and also modulates circadian rhythms in mice. In this study, we sought to determine whether voluntary wheel-running activity could prevent the proximate effects of high-fat diet consumption on circadian organization and behavioral rhythms in mice. Mice were housed with locked or freely rotating running wheels and fed chow or high-fat diet for 1 week and rhythms of locomotor activity, eating behavior, and molecular timekeeping (PERIOD2::LUCIFERASE luminescence rhythms) in ex vivo tissues were measured. Wheel-running activity delayed the phase of the liver rhythm by 4 h in both chow- and high-fat diet-fed mice. The delayed liver phase was specific to wheel-running activity since an enriched environment without the running wheel did not alter the phase of the liver rhythm. In addition, wheel-running activity modulated the effect of high-fat diet consumption on the daily rhythm of eating behavior. While high-fat diet consumption caused eating events to be more evenly dispersed across the 24 h-day in both locked-wheel and wheel-running mice, the effect of high-fat diet was much less pronounced in wheel-running mice. Together these data demonstrate that wheel-running activity is a salient factor that modulates liver phase and eating behavior rhythms in both chow- and high-fat-diet fed mice. Wheel-running activity in mice is both a source of exercise and a self-motivating, rewarding behavior. Understanding the putative reward-related mechanisms whereby wheel-running activity alters circadian rhythms could have implications for human obesity since palatable food and exercise may modulate similar reward circuits. PMID:24624109

Reinventing the wheel: comparison of two wheel cage styles for assessing mouse voluntary running activity.

PubMed

Seward, T; Harfmann, B D; Esser, K A; Schroder, E A

2018-04-01

Voluntary wheel cage assessment of mouse activity is commonly employed in exercise and behavioral research. Currently, no standardization for wheel cages exists resulting in an inability to compare results among data from different laboratories. The purpose of this study was to determine whether the distance run or average speed data differ depending on the use of two commonly used commercially available wheel cage systems. Two different wheel cages with structurally similar but functionally different wheels (electromechanical switch vs. magnetic switch) were compared side-by-side to measure wheel running data differences. Other variables, including enrichment and cage location, were also tested to assess potential impacts on the running wheel data. We found that cages with the electromechanical switch had greater inherent wheel resistance and consistently led to greater running distance per day and higher average running speed. Mice rapidly, within 1-2 days, adapted their running behavior to the type of experimental switch used, suggesting these running differences are more behavioral than due to intrinsic musculoskeletal, cardiovascular, or metabolic limits. The presence of enrichment or location of the cage had no detectable impact on voluntary wheel running. These results demonstrate that mice run differing amounts depending on the type of cage and switch mechanism used and thus investigators need to report wheel cage type/wheel resistance and use caution when interpreting distance/speed run across studies. NEW & NOTEWORTHY The results of this study highlight that mice will run different distances per day and average speed based on the inherent resistance present in the switch mechanism used to record data. Rapid changes in running behavior for the same mouse in the different cages demonstrate that a strong behavioral factor contributes to classic exercise outcomes in mice. Caution needs to be taken when interpreting mouse voluntary wheel running activity to include potential behavioral input and physiological parameters.

Cause of Thermal Fatigue Cracking in Metroliner Wheels

DOT National Transportation Integrated Search

1977-03-01

One new wheel and two used wheels (one with a thermal crack in the tread) were examined for mechanical properties, macrostructure, microstructure, and residual stresses. Similar examinations were conducted on three new wheels which were first subject...

Friction drive position transducer

NASA Astrophysics Data System (ADS)

Waclawik, Ronald E.; Cayer, James L.; Lapointe, Kenneth M.

1991-10-01

A spring force loaded contact wheel mounted in a stationary position relative to a reciprocating shaft is disclosed. The apparatus of the present invention includes a tensioning assembly for maintaining absolute contact between the contact wheel and the reciprocating shaft wherein the tensioning assembly urges the contact wheel against the shaft to maintain contact therebetween so that the wheel turns as the shaft is linearly displaced. A rotary encoding device is coupled to the wheel for translating the angular and rotational movement thereof into an electronic signal for providing linear displacement information and derivative data with respect to displacement of the shaft. Absolute friction contact and cooperative interaction between the shaft and the contact wheel is further enhanced in the preferred embodiment by advantageously selecting the types of surface finish and the amount of surface area of the contact wheel relative to the surface condition of the shaft as well as by reducing the moment of inertia of the contact wheel.

Friction drive position transducer

NASA Astrophysics Data System (ADS)

Waclawik, Ronald E.; Cayer, James L.; Lapointe, Kenneth M.

1993-06-01

A spring force loaded contact wheel mounted in a stationary position relative to a reciprocating shaft is disclosed. The apparatus of the present invention includes a tensioning assembly for maintaining absolute contact between the contact wheel and the reciprocating shaft wherein the tensioning assembly urges the contact wheel against the shaft to maintain contact there between so that the wheel turn as the shaft is linearly displaced. A rotary encoding device is coupled to the wheel for translating the angular and rotational movement thereof into an electronic signal for providing linear displacement information and derivative data with respect to displacement of the shaft. Absolute friction contact and cooperative interaction between the shaft and the contact wheel is further enhanced in the preferred embodiment by advantageously selecting the type of surface finish and the amount of surface area of the contact wheel relative to the surface condition of the shaft as well as by reducing the moment of inertia of the contact wheel.

A DFT study on the enthalpies of thermite reactions and enthalpies of formation of metal composite oxide

NASA Astrophysics Data System (ADS)

Zhang, Yu-ying; Wang, Meng-jie; Chang, Chun-ran; Xu, Kang-zhen; Ma, Hai-xia; Zhao, Feng-qi

2018-05-01

The standard thermite reaction enthalpies (ΔrHmθ) for seven metal oxides were theoretically analyzed using density functional theory (DFT) under five different functional levels, and the results were compared with experimental values. Through the comparison of the linear fitting constants, mean error and root mean square error, the Perdew-Wang functional within the framework of local density approximation (LDA-PWC) and Perdew-Burke-Ernzerhof exchange-correlation functional within the framework of generalized gradient approximation (GGA-PBE) were selected to further calculate the thermite reaction enthalpies for metal composite oxides (MCOs). According to the Kirchhoff formula, the standard molar reaction enthalpies for these MCOs were obtained and their standard molar enthalpies of formation (ΔfHmθ) were finally calculated. The results indicated that GGA-PBE is the most suitable one out of the total five methods to calculate these oxides. Tungstate crystals present the maximum deviation of the enthalpies of thermite reactions for MCOs and these of their physical metal oxide mixtures, but ferrite crystals are the minimum. The correlation coefficients are all above 0.95, meaning linear fitting results are very precise. And the molar enthalpies of formation for NiMoO4, CuMoO4, PbZrO3 (Pm/3m), PbZrO3 (PBA2), PbZrO3 (PBam), MgZrO3, CdZrO3, MnZrO3, CuWO4 and Fe2WO6 were first obtained as -1078.75, -1058.45, -1343.87, -1266.54, -1342.29, -1333.03, -1210.43, -1388.05, -1131.07 and - 1860.11 kJ·mol-1, respectively.

Enthalpy of Formation for Cu–Zn–Sn–S (CZTS) Calculated from Surface Binding Energies Experimentally Measured by Ion Sputtering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baryshev, Sergey V.; Thimsen, Elijah

2015-04-14

Herein, we report an analytical procedure to calculate the enthalpy of formation for thin film multinary compounds from sputtering rates measured during ion bombardment. The method is based on Sigmunds sputtering theory and the BornHaber cycle. Using this procedure, an enthalpy of formation for a CZTS film of the composition Cu1.9Zn1.5Sn0.8S4 was measured as -930 +/- 98 kJ mol1. This value is much more negative than the sum of the enthalpies of formation for the constituent binary compounds, meaning the multinary formation reaction is predicted to be exothermic. The measured enthalpy of formation was used to estimate the temperature dependencemore » of the Gibbs free energy of reaction, which appears consistent with many experimental reports in the CZTS processing literature.« less

Estimating the melting point, entropy of fusion, and enthalpy of fusion of organic compounds via SPARC.

PubMed

Whiteside, T S; Hilal, S H; Brenner, A; Carreira, L A

2016-08-01

The entropy of fusion, enthalpy of fusion, and melting point of organic compounds can be estimated through three models developed using the SPARC (SPARC Performs Automated Reasoning in Chemistry) platform. The entropy of fusion is modelled through a combination of interaction terms and physical descriptors. The enthalpy of fusion is modelled as a function of the entropy of fusion, boiling point, and flexibility of the molecule. The melting point model is the enthalpy of fusion divided by the entropy of fusion. These models were developed in part to improve SPARC's vapour pressure and solubility models. These models have been tested on 904 unique compounds. The entropy model has a RMS of 12.5 J mol(-1) K(-1). The enthalpy model has a RMS of 4.87 kJ mol(-1). The melting point model has a RMS of 54.4°C.

Energetics of the molecular interactions of L-cysteine, L-serine, and L-asparagine in aqueous propylene glycol solutions at 298.15 K

NASA Astrophysics Data System (ADS)

Mezhevoi, I. N.; Badelin, V. G.

2015-03-01

Integral enthalpies of dissolution Δsol H m of L-cysteine, L-serine, and L-asparagine in aqueous solutions of 1,3-propylene glycol at organic solvent concentrations of up to 0.26 mole fraction are measured via the thermochemistry of dissolution. Standard enthalpies of dissolution (Δsol H ○) and transfer (Δtr H ○) of amino acids from water to a mixed solvent are calculated. It is found that the calculated enthalpy coefficients of pair interactions of the amino acids with polyhydric alcohol molecules have positive values. The effect the arrangement of the hydroxyl group in the structure of polyhydric alcohols has on the enthalpy of interaction of amino acids in aqueous solutions is revealed. The effect of different types of interactions in solutions and the structural features of biomolecules and cosolvents on the enthalpy of dissolution of amino acids is analyzed.

Experimental and computational investigation of the thermochemistry of the six isomers of dichloroaniline.

PubMed

Ribeiro da Silva, Manuel A V; Amaral, Luísa M P F; Gomes, José R B

2006-07-27

The standard (p(o) = 0.1 MPa) molar enthalpies of formation of 2,3-, 2,4-, 2,5-, 2,6-, 3,4- and 3,5-dichloroanilines were derived from the standard molar energies of combustion, in oxygen, to yield CO(2)(g), N(2)(g) and HCl.600H(2)O(l), at T = 298.15 K, measured by rotating bomb combustion calorimetry. The Calvet high-temperature vacuum sublimation technique was used to measure the enthalpies of sublimation of the six isomers. These two thermodynamic parameters yielded the standard molar enthalpies of formation of the six isomers of dichloroaniline, in the gaseous phase, at T = 298.15 K. The gas-phase enthalpies of formation were also estimated by G3MP2B3 calculations, which were further extended to the computation of gas-phase acidities, proton affinities, and ionization enthalpies.

Characterization of Adsorption Enthalpy of Novel Water-Stable Zeolites and Metal-Organic Frameworks

NASA Astrophysics Data System (ADS)

Kim, Hyunho; Cho, H. Jeremy; Narayanan, Shankar; Yang, Sungwoo; Furukawa, Hiroyasu; Schiffres, Scott; Li, Xiansen; Zhang, Yue-Biao; Jiang, Juncong; Yaghi, Omar M.; Wang, Evelyn N.

2016-01-01

Water adsorption is becoming increasingly important for many applications including thermal energy storage, desalination, and water harvesting. To develop such applications, it is essential to understand both adsorbent-adsorbate and adsorbate-adsorbate interactions, and also the energy required for adsorption/desorption processes of porous material-adsorbate systems, such as zeolites and metal-organic frameworks (MOFs). In this study, we present a technique to characterize the enthalpy of adsorption/desorption of zeolites and MOF-801 with water as an adsorbate by conducting desorption experiments with conventional differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). With this method, the enthalpies of adsorption of previously uncharacterized adsorbents were estimated as a function of both uptake and temperature. Our characterizations indicate that the adsorption enthalpies of type I zeolites can increase to greater than twice the latent heat whereas adsorption enthalpies of MOF-801 are nearly constant for a wide range of vapor uptakes.

The high-temperature heat capacity of the (Th,U)O 2 and (U,Pu)O 2 solid solutions

DOE PAGES

Valu, S. O.; Benes, O.; Manara, D.; ...

2016-11-09

The enthalpy increment data for the (Th,U)O 2 and (U,Pu)O 2 solid solutions are reviewed and complemented with new experimental data (400–1773 K) and many-body potential model simulations. The results of the review show that from room temperature up to about 2000 K the enthalpy data are in agreement with the additivity rule (Neumann-Kopp) in the whole composition range. Above 2000 K the effect of Oxygen Frenkel Pair (OFP) formation leads to an excess enthalpy (heat capacity) that is modeled using the enthalpy and entropy of OFP formation from the end-members. Here, a good agreement with existing experimental work ismore » observed, and a reasonable agreement with the results of the many-body potential model, which indicate the presence of the diffuse Bredig (superionic) transition that is not found in the experimental enthalpy increment data.« less

High-pressure, ambient temperature hydrogen storage in metal-organic frameworks and porous carbon

NASA Astrophysics Data System (ADS)

Beckner, Matthew; Dailly, Anne

2014-03-01

We investigated hydrogen storage in micro-porous adsorbents at ambient temperature and pressures up to 320 bar. We measured three benchmark adsorbents: two metal-organic frameworks, Cu3(1,3,5-benzenetricarboxylate)2 [Cu3(btc)2; HKUST-1] and Zn4O(1,3,5-benzenetribenzoate)2 [Zn4O(btb)2; MOF-177], and the activated carbon MSC-30. In this talk, we focus on adsorption enthalpy calculations using a single adsorption isotherm. We use the differential form of the Claussius-Clapeyron equation applied to the Dubinin-Astakhov adsorption model to calculate adsorption enthalpies. Calculation of the adsorption enthalpy in this way gives a temperature independent enthalpy of 5-7 kJ/mol at the lowest coverage for the three materials investigated. Additionally, we discuss the assumptions and corrections that must be made when calculating adsorption isotherms at high-pressure and adsorption enthalpies.

Enthalpy of Formation of N 2 H 4 (Hydrazine) Revisited

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feller, David; Bross, David H.; Ruscic, Branko

2017-08-02

In order to address the accuracy of the long-standing experimental enthalpy of formation of gas-phase hydrazine, fully confirmed in earlier versions of Active Thermochemical Tables (ATcT), the provenance of that value is re-examined in light of new high-end calculations of the Feller-Peterson-Dixon (FPD) variety. An overly optimistic determination of the vaporization enthalpy of hydrazine, which created an unrealistically strong connection between the gas phase thermochemistry and the calorimetric results defining the thermochemistry of liquid hydrazine was identified as the probable culprit. The new enthalpy of formation of gas-phase hydrazine, based on balancing all available knowledge, was determined to be 111.57more » ± 0.47 kJ/mol at 0 K (97.41 kJ/mol at 298.15 K). Close agreement was found between the ATcT (even excluding the latest theoretical result) and FPD enthalpies.« less

Characterization of Adsorption Enthalpy of Novel Water-Stable Zeolites and Metal-Organic Frameworks

PubMed Central

Kim, Hyunho; Cho, H. Jeremy; Narayanan, Shankar; Yang, Sungwoo; Furukawa, Hiroyasu; Schiffres, Scott; Li, Xiansen; Zhang, Yue-Biao; Jiang, Juncong; Yaghi, Omar M.; Wang, Evelyn N.

2016-01-01

Water adsorption is becoming increasingly important for many applications including thermal energy storage, desalination, and water harvesting. To develop such applications, it is essential to understand both adsorbent-adsorbate and adsorbate-adsorbate interactions, and also the energy required for adsorption/desorption processes of porous material-adsorbate systems, such as zeolites and metal-organic frameworks (MOFs). In this study, we present a technique to characterize the enthalpy of adsorption/desorption of zeolites and MOF-801 with water as an adsorbate by conducting desorption experiments with conventional differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). With this method, the enthalpies of adsorption of previously uncharacterized adsorbents were estimated as a function of both uptake and temperature. Our characterizations indicate that the adsorption enthalpies of type I zeolites can increase to greater than twice the latent heat whereas adsorption enthalpies of MOF-801 are nearly constant for a wide range of vapor uptakes. PMID:26796523

Enthalpy of Formation of N2H4 (Hydrazine) Revisited.

PubMed

Feller, David; Bross, David H; Ruscic, Branko

2017-08-17

In order to address the accuracy of the long-standing experimental enthalpy of formation of gas-phase hydrazine, fully confirmed in earlier versions of Active Thermochemical Tables (ATcT), the provenance of that value is re-examined in light of new high-end calculations of the Feller-Peterson-Dixon (FPD) variety. An overly optimistic determination of the vaporization enthalpy of hydrazine, which created an unrealistically strong connection between the gas phase thermochemistry and the calorimetric results defining the thermochemistry of liquid hydrazine, was identified as the probable culprit. The new enthalpy of formation of gas-phase hydrazine, based on balancing all available knowledge, was determined to be 111.57 ± 0.47 kJ/mol at 0 K (97.42 ± 0.47 kJ/mol at 298.15 K). Close agreement was found between the ATcT (even excluding the latest theoretical result) and the FPD enthalpy.

Mechanical Design Engineering Enabler Project wheel and wheel drives

NASA Technical Reports Server (NTRS)

Nutt, Richard E.; Couch, Britt K.; Holley, John L., Jr.; Garris, Eric S.; Staut, Paul V.

1992-01-01

Our group was assigned the responsibility of designing the wheel and wheel drive system for a proof-of-concept model of the lunar-based ENABLER. ENABLER is a multi-purpose, six wheeled vehicle designed to lift and transport heavy objects associated with the construction of a lunar base. The resulting design was based on the performance criteria of the ENABLER. The drive system was designed to enable the vehicle to achieve a speed of 7 mph on a level surface, climb a 30 percent grade, and surpass a one meter high object and one meter wide crevice. The wheel assemblies were designed to support the entire weight of the vehicle on two wheels. The wheels were designed to serve as the main component of the vehicle's suspension and will provide suitable traction for lunar-type surfaces. The expected performance of the drive system for the ENABLER was influenced by many mechanical factors. The expected top speed on a level sandy surface is 4 mph instead of the desired 7 mph. This is due to a lack of necessary power at the wheels. The lack of power resulted from dimension considerations that allowed only an eight horsepower engine and also from mechanical inefficiencies of the hydraulic system. However, the vehicle will be able to climb a 30 percent grade, surpass a one meter high object and one meter wide crevice. The wheel assemblies will be able to support the entire weight of the vehicle on two wheels. The wheels will also provide adequate suspension for the vehicle and sufficient traction for lunar-type surfaces.

Wheelchair caster shimmy and turning resistance.

PubMed

Kauzlarich, J J; Bruning, T; Thacker, J G

1984-07-01

The equations for wheelchair caster wheel shimmy are presented along with experimental data. The report includes the theory and performance of single wheel casters for a variety of tires, and a new design for wheelchair casters using a grooved dual-tread tire or co-rotating caster wheels. The dual-tread tire was found to significantly inhibit caster shimmy. The turning resistance due to a grooved caster wheel tire with a 1/2-inch groove was found to be 10 percent greater than for an ungrooved caster wheel tire. The analysis includes the methodology and the results of experiments developed to measure the sliding friction turning moment of the wheelchair caster wheel. A number of commercial wheelchair caster wheels were tested and the results for shimmy are presented.

Tread buildup on railroad wheels.

DOT National Transportation Integrated Search

2015-04-01

Based on the results of wheel slide tests and an inspection of wheels, the root cause of tread buildup (TBU) was identified as : wheel slide caused by excessive brake force. During the tests, TBU accumulated to the greatest heights under dry conditio...

Four-wheel dual braking for automobiles

NASA Technical Reports Server (NTRS)

Edwards, H. B.

1981-01-01

Each master cylinder applies braking power to all four wheels unlike conventional systems where cylinder operates only two wheels. If one master system fails because of fluid loss, other stops car by braking all four wheels although at half force.

Study of the Correlation between the Performances of Lunar Vehicle Wheels Predicted by the Nepean Wheeled Vehicle Performance Model and Test Data

NASA Technical Reports Server (NTRS)

Wong, J. Y.; Asnani, V. M.

2008-01-01

This paper describes the results of a study of the correlation between the performances of wheels for lunar vehicles predicted using the Nepean wheeled vehicle performance model (NWVPM), developed under the auspices of Vehicle Systems Development Corporation, Ottawa, Canada, and the corresponding test data presented in Performance evaluation of wheels for lunar vehicles , Technical Report M-70-2, prepared for George C. Marshall Space Flight Center, National Aeronautics and Space Administration (NASA), USA, by the US Army Engineer Waterways Experiment Station (WES). The NWVPM was originally developed for design and performance evaluation of terrestrial off-road wheeled vehicles. The purpose of this study is to assess the potential of the NWVPM for evaluating wheel candidates for the new generation of extra-terrestrial vehicles. Two versions of a wire-mesh wheel and a hoop-spring wheel, which were considered as candidates for lunar roving vehicles for the NASA Apollo program in the late 1960s, together with a pneumatic wheel were examined in this study. The tractive performances of these wheels and of a 464 test vehicle with the pneumatic wheels on air-dry sand were predicted using the NWVPM and compared with the corresponding test data obtained under Earth s gravity and previously documented in the above-named report. While test data on wheel or vehicle performances obtained under Earth s gravity may not necessarily be representative of those on extra-terrestrial bodies, because of the differences in gravity and in environmental conditions, such as atmospheric pressure, it is still a valid approach to use test data obtained under Earth s gravity to evaluate the predictive capability of the NWVPM and its potential applications to predicting wheel or wheeled rover performances on extra-terrestrial bodies. Results of this study show that, using the ratio (P20/W) of the drawbar pull to normal load at 20 per cent slip as a performance indicator, there is a reasonable correlation between the predictions and experimental data. This indicates that the NWVPM has the potential as an engineering tool for evaluating wheel candidates for a future generation of extra-terrestrial vehicles, provided that appropriate input data are available.

Reaction Wheel Disturbance Modeling, Jitter Analysis, and Validation Tests for Solar Dynamics Observatory

NASA Technical Reports Server (NTRS)

Liu,Kuo-Chia; Maghami, Peiman; Blaurock, Carl

2008-01-01

The Solar Dynamics Observatory (SDO) aims to study the Sun's influence on the Earth by understanding the source, storage, and release of the solar energy, and the interior structure of the Sun. During science observations, the jitter stability at the instrument focal plane must be maintained to less than a fraction of an arcsecond for two of the SDO instruments. To meet these stringent requirements, a significant amount of analysis and test effort has been devoted to predicting the jitter induced from various disturbance sources. One of the largest disturbance sources onboard is the reaction wheel. This paper presents the SDO approach on reaction wheel disturbance modeling and jitter analysis. It describes the verification and calibration of the disturbance model, and ground tests performed for validating the reaction wheel jitter analysis. To mitigate the reaction wheel disturbance effects, the wheels will be limited to operate at low wheel speeds based on the current analysis. An on-orbit jitter test algorithm is also presented in the paper which will identify the true wheel speed limits in order to ensure that the wheel jitter requirements are met.

Thickness-Independent Ultrasonic Imaging Applied to Abrasive Cut-Off Wheels: An Advanced Aerospace Materials Characterization Method for the Abrasives Industry. A NASA Lewis Research Center Technology Transfer Case History

NASA Technical Reports Server (NTRS)

Roth, Don J.; Farmer, Donald A.

1998-01-01

Abrasive cut-off wheels are at times unintentionally manufactured with nonuniformity that is difficult to identify and sufficiently characterize without time-consuming, destructive examination. One particular nonuniformity is a density variation condition occurring around the wheel circumference or along the radius, or both. This density variation, depending on its severity, can cause wheel warpage and wheel vibration resulting in unacceptable performance and perhaps premature failure of the wheel. Conventional nondestructive evaluation methods such as ultrasonic c-scan imaging and film radiography are inaccurate in their attempts at characterizing the density variation because a superimposing thickness variation exists as well in the wheel. In this article, the single transducer thickness-independent ultrasonic imaging method, developed specifically to allow more accurate characterization of aerospace components, is shown to precisely characterize the extent of the density variation in a cut-off wheel having a superimposing thickness variation. The method thereby has potential as an effective quality control tool in the abrasives industry for the wheel manufacturer.

Broken rims in railroad wheels.

DOT National Transportation Integrated Search

2014-12-01

Broken wheels are one of the most common types of equipment-caused train accidents. The failure of rail car wheel rims, which : are usually the result of shattered rims or vertical split rims (VSR), are the leading cause of wheel-related accidents, a...

Experimental studies of breaking of elastic tired wheel under variable normal load

NASA Astrophysics Data System (ADS)

Fedotov, A. I.; Zedgenizov, V. G.; Ovchinnikova, N. I.

2017-10-01

The paper analyzes the braking of a vehicle wheel subjected to disturbances of normal load variations. Experimental tests and methods for developing test modes as sinusoidal force disturbances of the normal wheel load were used. Measuring methods for digital and analogue signals were used as well. Stabilization of vehicle wheel braking subjected to disturbances of normal load variations is a topical issue. The paper suggests a method for analyzing wheel braking processes under disturbances of normal load variations. A method to control wheel baking processes subjected to disturbances of normal load variations was developed.

Proposal to use vibration analysis steering components and car body to monitor, for example, the state of unbalance wheel

NASA Astrophysics Data System (ADS)

Janczur, R.

2016-09-01

The results of road tests of car VW Passat equipped with tires of size 195/65 R15, on the influence of the unbalancing front wheel on vibration of the parts of steering system, steering wheel and the body of the vehicle have been presented in this paper. Unbalances wheels made using weights of different masses, placed close to the outer edge of the steel rim and checked on the machine Hunter GSP 9700 for balancing wheels. The recorded waveforms vibration steering components and car body, at different constant driving speeds, subjected to spectral analysis to determine the possibility of isolating vibration caused by unbalanced wheel in various states and coming from good quality asphalt road surface. The results were discussed in terms of the possibility of identifying the state of unbalancing wheels and possible changes in radial stiffness of the tire vibration transmitted through the system driving wheel on the steering wheel. Vibration analysis steering components and car body, also in the longitudinal direction, including information from the CAN bus of the state of motion of the car, can be used to monitor the development of the state of unbalance wheel, tire damage or errors shape of brake discs or brake drums, causing pulsations braking forces.

Group vector space method for estimating enthalpy of vaporization of organic compounds at the normal boiling point.

PubMed

Wenying, Wei; Jinyu, Han; Wen, Xu

2004-01-01

The specific position of a group in the molecule has been considered, and a group vector space method for estimating enthalpy of vaporization at the normal boiling point of organic compounds has been developed. Expression for enthalpy of vaporization Delta(vap)H(T(b)) has been established and numerical values of relative group parameters obtained. The average percent deviation of estimation of Delta(vap)H(T(b)) is 1.16, which show that the present method demonstrates significant improvement in applicability to predict the enthalpy of vaporization at the normal boiling point, compared the conventional group methods.

Characterization and thermogravimetric analysis of lanthanide hexafluoroacetylacetone chelates

DOE PAGES

Shahbazi, Shayan; Stratz, S. Adam; Auxier, John D.; ...

2016-08-30

This work reports the thermodynamic characterizations of organometallic species as a vehicle for the rapid separation of volatile nuclear fission products via gas chromatography due to differences in adsorption enthalpy. Because adsorption and sublimation thermodynamics are linearly correlated, there is considerable motivation to determine sublimation enthalpies. A method of isothermal thermogravimetric analysis, TGA-MS and melting point analysis are employed on thirteen lanthanide 1,1,1,5,5,5-hexafluoroacetylacetone complexes to determine sublimation enthalpies. An empirical correlation is used to estimate adsorption enthalpies of lanthanide complexes on a quartz column from the sublimation data. Additionally, four chelates are characterized by SC-XRD, elemental analysis, FTIR and NMR.

Effect of Tryptophan and Asparagine Structure on the Enthalpic Characteristics of Their Dissolution in Aqueous Solutions of Sodium Dodecyl Sulfate

NASA Astrophysics Data System (ADS)

Mezhevoi, I. N.; Badelin, V. G.; Tyunina, E. Yu.; Kamkina, S. V.

2018-03-01

The integral enthalpies of dissolution of L-tryptophan and L-asparagine in aqueous solutions of sodium dodecyl sulfate (surfactant) at surfactant concentrations of up to 0.05 mol/kg of the solvent are determined and estimated calorimetrically. Standard values of the enthalpies of dissolution and transfer of amino acids from water to a mixed solvent are calculated. The calculated enthalpy coefficients of pair interactions between amino acids and surfactant molecules have positive values. Hydrophobic interactions between amino acids and surfactants have the dominant effect on the enthalpy characteristics of the interaction in a three-component solution.

Calculation of Five Thermodynamic Molecular Descriptors by Means of a General Computer Algorithm Based on the Group-Additivity Method: Standard Enthalpies of Vaporization, Sublimation and Solvation, and Entropy of Fusion of Ordinary Organic Molecules and Total Phase-Change Entropy of Liquid Crystals.

PubMed

Naef, Rudolf; Acree, William E

2017-06-25

The calculation of the standard enthalpies of vaporization, sublimation and solvation of organic molecules is presented using a common computer algorithm on the basis of a group-additivity method. The same algorithm is also shown to enable the calculation of their entropy of fusion as well as the total phase-change entropy of liquid crystals. The present method is based on the complete breakdown of the molecules into their constituting atoms and their immediate neighbourhood; the respective calculations of the contribution of the atomic groups by means of the Gauss-Seidel fitting method is based on experimental data collected from literature. The feasibility of the calculations for each of the mentioned descriptors was verified by means of a 10-fold cross-validation procedure proving the good to high quality of the predicted values for the three mentioned enthalpies and for the entropy of fusion, whereas the predictive quality for the total phase-change entropy of liquid crystals was poor. The goodness of fit ( Q ²) and the standard deviation (σ) of the cross-validation calculations for the five descriptors was as follows: 0.9641 and 4.56 kJ/mol ( N = 3386 test molecules) for the enthalpy of vaporization, 0.8657 and 11.39 kJ/mol ( N = 1791) for the enthalpy of sublimation, 0.9546 and 4.34 kJ/mol ( N = 373) for the enthalpy of solvation, 0.8727 and 17.93 J/mol/K ( N = 2637) for the entropy of fusion and 0.5804 and 32.79 J/mol/K ( N = 2643) for the total phase-change entropy of liquid crystals. The large discrepancy between the results of the two closely related entropies is discussed in detail. Molecules for which both the standard enthalpies of vaporization and sublimation were calculable, enabled the estimation of their standard enthalpy of fusion by simple subtraction of the former from the latter enthalpy. For 990 of them the experimental enthalpy-of-fusion values are also known, allowing their comparison with predictions, yielding a correlation coefficient R ² of 0.6066.

Harsh medicine. [retail wheeling experiment in Michigan and side effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Studness, C.M.

1993-07-15

Retailing wheeling's harmful side-effects may surface in a Michigan experiment. In the final analysis, the debate over retail wheeling is about whether there will be direct price competition in the electric power industry. Retail wheeling would extend to the electric power market the same freedom of choice among customers that is present elsewhere in the economy. It would provide a mechanism through which competition could enforce an efficient allocation of resources. It also undoubtedly would eliminate most of the huge discrepancies that exist between so many neighboring service areas. It is unlikely that permitting retail wheeling would actually result inmore » much wheeling or loss of load. Utilities will no doubt meet the threat of the loss of load by cutting rates to hold their customers. Hence, the primary effect would be on the pricing of electricity, not the wheeling of power. The retail wheeling experiment under consideration in Michigan can become an important step toward making the utility industry more efficient for the nation and more equitable for ratepayers. Unfortunately, it also is potentially unfair to the utilities involved. A retail wheeling experiment in one state is likely to put those utilities at risk for competitive attack, but is unlikely to give those utilities the countervailing power to use retail wheeling elsewhere to market their power. Fairness and economic efficiency require that retail wheeling exist everywhere, and that is is accessible to utilities as well as non-utilities.« less

Phenomena of Foamed Concrete under Rolling of Aircraft Wheels

NASA Astrophysics Data System (ADS)

Jiang, Chun-shui; Yao, Hong-yu; Xiao, Xian-bo; Kong, Xiang-jun; Shi, Ya-jie

2014-04-01

Engineered Material Arresting System (EMAS) is an effective technique to reduce hazards associated with aircraft overrunning runway. In order to ascertain phenomena of the foamed concrete used for EMAS under rolling of aircraft wheel, a specially designed experimental setup was built which employed Boeing 737 aircraft wheels bearing actual vertical loads to roll through the foamed concrete. A number of experiments were conducted upon this setup. It is discovered that the wheel rolls the concrete in a pure rolling manner and crushes the concrete downwards, instead of crushing it forward, as long as the concrete is not higher than the wheel axle. The concrete is compressed into powder in-situ by the wheel and then is brought to bottom of the wheel. The powder under the wheel is loose and thus is not able to sustain wheel braking. It is also found that after being rolled by the wheel the concrete exhibits either of two states, i.e. either 'crushed through' whole thickness of the concrete or 'crushed halfway', depending on combination of strength of the concrete, thickness of the concrete, vertical load the wheel carries, tire dimension and tire pressure. A new EMAS design concept is developed that if an EMAS design results in the 'crushed through' state for the main gears while the 'crushed halfway' state for the nose gear, the arresting bed would be optimal to accommodate the large difference in strength between the nose gear and the main gear of an aircraft.

Wheel-running reinforcement in free-feeding and food-deprived rats.

PubMed

Belke, Terry W; Pierce, W David

2016-03-01

Rats experiencing sessions of 30min free access to wheel running were assigned to ad-lib and food-deprived groups, and given additional sessions of free wheel activity. Subsequently, both ad-lib and deprived rats lever pressed for 60s of wheel running on fixed ratio (FR) 1, variable ratio (VR) 3, VR 5, and VR 10 schedules, and on a response-initiated variable interval (VI) 30s schedule. Finally, the ad-lib rats were switched to food deprivation and the food-deprived rats were switched to free food, as rats continued responding on the response-initiated VI 30-s schedule. Wheel running functioned as reinforcement for both ad-lib and food-deprived rats. Food-deprived rats, however, ran faster and had higher overall lever-pressing rates than free-feeding rats. On the VR schedules, wheel-running rates positively correlated with local and overall lever pressing rates for deprived, but not ad-lib rats. On the response-initiated VI 30s schedule, wheel-running rates and lever-pressing rates changed for ad-lib rats switched to food deprivation, but not for food-deprived rats switched to free-feeding. The overall pattern of results suggested different sources of control for wheel running: intrinsic motivation, contingencies of automatic reinforcement, and food-restricted wheel running. An implication is that generalizations about operant responding for wheel running in food-deprived rats may not extend to wheel running and operant responding of free-feeding animals. Copyright © 2015 Elsevier B.V. All rights reserved.

Wheel-running attenuates intravenous cocaine self-administration in rats: sex differences.

PubMed

Cosgrove, Kelly P; Hunter, Robb G; Carroll, Marilyn E

2002-10-01

This experiment examines the effect of access to a running-wheel on intravenous cocaine self-administration in male and female rats. Rats maintained at 85% of their free-feeding body weight were first exposed to the running-wheel alone during the 6-h sessions until behavior stabilized for 14 days. Intravenous cannulae were then implanted, and the rats were trained to self-administer a low dose of cocaine (0.2 mg/kg) under a fixed-ratio (FR 1) schedule during the 6-h sessions, while the wheel remained inactive and cocaine self-administration stabilized (cocaine-only condition). Next, the wheel access and cocaine self-administration were concurrently available followed by a period of cocaine-only. Behavior was allowed to stabilize for 10 days at each phase. During wheel access, cocaine infusions decreased by 21.9% in males and 70.6% in females compared to the cocaine-only condition; the effect was statistically significant in females. Infusions increased to baseline levels when wheel access was terminated. When cocaine infusions were concurrently available, wheel revolutions were reduced by 63.7% and 61.5% in males and females, respectively, compared to the wheel-only condition. This result did not differ due to sex, but it was statistically significant when data from males and females were combined. These results indicate that wheel-running activity had a greater suppressant effect on cocaine self-administration in females than in males, and in females, wheel-running and cocaine self-administration are substitutable as reinforcers.

Wheel/Rail Noise and Vibration : Volume 1. Mechanics of Wheel Rail Noise Generation.

DOT National Transportation Integrated Search

1975-05-01

The final reports are reported of a project to develop a basic understanding of urban transit wheel/rail noise control measures. Analytical models of impedance, response, radiation efficiency, and directivity of wheels and rails are presented and com...

All-wheel drive and winter-weather safety.

DOT National Transportation Integrated Search

2013-03-01

It is frequently stated that people living in northern states, the so called Snowbelt of the United : States, benefit with respect to safety from driving all-wheel or four-wheel drive vehicles as : opposed to front or rear-wheel drive only. This stud...

In-Service Performance and Costs of Methods to Control Urban Rail System Noise

DOT National Transportation Integrated Search

1979-12-01

This study evaluates the acoustic and economic effectiveness of five methods of controlling wheel/rail noise and vibration on urban rail transit systems, namely: rail grinding, wheel truing, resilient wheels, ring-damped wheels, and welded vs. jointe...

Automatic Mechetronic Wheel Light Device

DOEpatents

Khan, Mohammed John Fitzgerald

2004-09-14

A wheel lighting device for illuminating a wheel of a vehicle to increase safety and enhance aesthetics. The device produces the appearance of a "ring of light" on a vehicle's wheels as the vehicle moves. The "ring of light" can automatically change in color and/or brightness according to a vehicle's speed, acceleration, jerk, selection of transmission gears, and/or engine speed. The device provides auxiliary indicator lights by producing light in conjunction with a vehicle's turn signals, hazard lights, alarm systems, and etc. The device comprises a combination of mechanical and electronic components and can be placed on the outer or inner surface of a wheel or made integral to a wheel or wheel cover. The device can be configured for all vehicle types, and is electrically powered by a vehicle's electrical system and/or battery.

Wheel/rail noise generated by a high-speed train investigated with a line array of microphones

NASA Astrophysics Data System (ADS)

Barsikow, B.; King, W. F.; Pfizenmaier, E.

1987-10-01

Radiated noise generated by a high-speed electric train travelling at speeds up to 250 km/h has been measured with a line array of microphones mounted along the wayside in two different orientations. The test train comprised a 103 electric locomotive, four Intercity coaches, and a dynamo coach. Some of the wheels were fitted with experimental wheel-noise absorbers. By using the directional capabilities of the array, the locations of the dominant sources of wheel/rail radiated noise were identified on the wheels. For conventional wheels, these sources lie near or on the rim at an average height of about 0·2 m above the railhead. The effect of wheel-noise absorbers and freshly turned treads on radiated noise were also investigated.

Reinforcement of wheel running in BALB/c mice: role of motor activity and endogenous opioids.

PubMed

Vargas-Pérez, Héctor; Sellings, Laurie H L; Paredes, Raúl G; Prado-Alcalá, Roberto A; Díaz, José-Luis

2008-11-01

The authors investigated the effect of the opioid antagonist naloxone on wheel-running behavior in Balb/c mice. Naloxone delayed the acquisition of wheel-running behavior, but did not reduce the expression of this behavior once acquired. Delayed acquisition was not likely a result of reduced locomotor activity, as naloxone-treated mice did not exhibit reduced wheel running after the behavior was acquired, and they performed normally on the rotarod test. However, naloxone-blocked conditioned place preference for a novel compartment paired previously with wheel running, suggesting that naloxone may delay wheel-running acquisition by blocking the rewarding or reinforcing effects of the behavior. These results suggest that the endogenous opioid system mediates the initial reinforcing effects of wheel running that are important in acquisition of the behavior.

Enthalpy-entropy compensation: the role of solvation.

PubMed

Dragan, Anatoliy I; Read, Christopher M; Crane-Robinson, Colyn

2017-05-01

Structural modifications to interacting systems frequently lead to changes in both the enthalpy (heat) and entropy of the process that compensate each other, so that the Gibbs free energy is little changed: a major barrier to the development of lead compounds in drug discovery. The conventional explanation for such enthalpy-entropy compensation (EEC) is that tighter contacts lead to a more negative enthalpy but increased molecular constraints, i.e., a compensating conformational entropy reduction. Changes in solvation can also contribute to EEC but this contribution is infrequently discussed. We review long-established and recent cases of EEC and conclude that the large fluctuations in enthalpy and entropy observed are too great to be a result of only conformational changes and must result, to a considerable degree, from variations in the amounts of water immobilized or released on forming complexes. Two systems exhibiting EEC show a correlation between calorimetric entropies and local mobilities, interpreted to mean conformational control of the binding entropy/free energy. However, a substantial contribution from solvation gives the same effect, as a consequence of a structural link between the amount of bound water and the protein flexibility. Only by assuming substantial changes in solvation-an intrinsically compensatory process-can a more complete understanding of EEC be obtained. Faced with such large, and compensating, changes in the enthalpies and entropies of binding, the best approach to engineering elevated affinities must be through the addition of ionic links, as they generate increased entropy without affecting the enthalpy.

The gaseous enthalpy of formation of the ionic liquid 1-butyl-3-methylimidazolium dicyanamide from combustion calorimetry, vapor pressure measurements, and ab initio calculations.

PubMed

Emel'yanenko, Vladimir N; Verevkin, Sergey P; Heintz, Andreas

2007-04-04

Ionic liquids are attracting growing interest as alternatives to conventional molecular solvents. Experimental values of vapor pressure, enthalpy of vaporization, and enthalpy of formation of ionic liquids are the key thermodynamic quantities, which are required for the validation and development of the molecular modeling and ab initio methods toward this new class of solvents. In this work, the molar enthalpy of formation of the liquid 1-butyl-3-methylimidazolium dicyanamide, 206.2 +/- 2.5 kJ.mol-1, was measured by means of combustion calorimetry. The molar enthalpy of vaporization of 1-butyl-3-methylimidazolium dicyanamide, 157.2 +/- 1.1 kJ.mol-1, was obtained from the temperature dependence of the vapor pressure measured using the transpiration method. The latter method has been checked with measurements of 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide, where data are available from the effusion technique. The first experimental determination of the gaseous enthalpy of formation of the ionic liquid 1-butyl-3-methylimidazolium dicyanamide, 363.4 +/- 2.7 kJ.mol-1, from thermochemical measurements (combustion and transpiration) is presented. Ab initio calculations of the enthalpy of formation in the gaseous phase have been performed for 1-butyl-3-methylimidazolium dicyanamide using the G3MP2 theory. Excellent agreement with experimental results has been observed. The method developed opens a new way to obtain thermodynamic properties of ionic liquids which have not been available so far.

An examination of the thermodynamics of fusion, vaporization, and sublimation of (R,S)- and (R)-flurbiprofen by correlation gas chromatography.

PubMed

Umnahanant, Patamaporn; Hasty, Darrell; Chickos, James

2012-06-01

The vaporization, fusion, and sublimation enthalpies of (R,S)- and (R)-flurbiprofen at T = 298.15 K are reported and compared with literature values when available. Correlation gas chromatography experiments were first performed to identify appropriate standards that could be used for materials containing a single fluorine substituent. Subsequent correlations resulted in a vaporization enthalpy for (R,S)-flurbiprofen and (R)-flurbiprofen, ΔH(vap) (298.15 K), of (127.5 ± 5.5) and (127.4 ± 4.7) kJ mol, respectively. Fusion enthalpies, ΔH(fus) (387 K), of (28.2 ± and, ΔH(fus) (381 K), (22.8 ± kJ mol(-1) were also measured by differential scanning calorimetry for the racemic and chiral forms of flurbiprofen. Adjusted to T = 298.15 K and combined with the vaporization enthalpy resulted in sublimation enthalpies, ΔH(sub) (298.15 K), of (155.6 ± 5.8) and (145.1 ± 5.7) kJ mol(-1) for (R,S)- and (R)-flurbiprofen, respectively. The fusion enthalpy measured for the racemic form was in excellent agreement with the literature value, while the sublimation enthalpy varies substantially from previous work. Two weak solid-solid phase transitions were also observed for (R)-flurbiprofen at T = 353.9 K (0.30 ± 0.1) and 363.2 K (0.21 ± 0.03) kJ · mol(-1). Copyright © 2012 Wiley Periodicals, Inc.

Enthalpy of formation of anisole: implications for the controversy on the O-H bond dissociation enthalpy in phenol.

PubMed

Simões, Ricardo G; Agapito, Filipe; Diogo, Hermínio P; da Piedade, Manuel E Minas

2014-11-20

Significant discrepancies in the literature data for the enthalpy of formation of gaseous anisole, ΔfHmo(PhOCH3, g), have fueled an ongoing controversy regarding the most reliable enthalpy of formation of the phenoxy radical and of the gas phase O-H bond dissociation enthalpy, DHo(PhO-H), in phenol. In the present work ΔfHmo(PhOCH3, g) was reassessed using a combination of calorimetric determinations and high-level (W2-F12) ab initio calculations. Static-bomb combustion calorimetry led to the standard molar enthalpy of formation of liquid anisole at 298.15 K, ΔfHmo(PhOCH3, l) = −(117.1 ± 1.4) kJ·mol(-1). The corresponding enthalpy of vaporization was obtained as, ΔvapHmo(PhOCH3) = 46.41 ± 0.26 kJ·mol(-1), by Calvet-drop microcalorimetry. These results give ΔfHmo(PhOCH3, g) = −(70.7 ± 1.4) kJ·mol(-1), in excellent agreement with ΔfHmo(PhOCH3, g) = −(70.8 ± 3.2) kJ·mol(-1), obtained from the W2-F12 calculations. The ΔfHmo(PhOCH3, g) here recommended leads to ΔfHmo(PhO•, g) = 55.5 ± 2.4 kJ·mol(-)1 and DH°(PhO-H) = 368.1 ± 2.6 kJ·mol(-1).

Break in Raised Tread on Curiosity Wheel

NASA Image and Video Library

2017-03-21

Two of the raised treads, called grousers, on the left middle wheel of NASA's Curiosity Mars rover broke during the first quarter of 2017, including the one seen partially detached at the top of the wheel in this image from the Mars Hand Lens Imager (MAHLI) camera on the rover's arm. This image was taken on March 19, 2017, as part of a set used by rover team members to inspect the condition of the rover's six wheels during the 1,641st Martian day, or sol, of Curiosity's work on Mars. Holes and tears in the wheels worsened significantly during 2013 as Curiosity was crossing terrain studded with sharp rocks on the route from near its 2012 landing site to the base of Mount Sharp. Team members have used MAHLI systematically since then to watch for when any of the zig-zag shaped grousers begin to break. The last prior set of wheel-inspection images from before Sol 1641 was taken on Jan. 27, 2017, (Sol 1591) and revealed no broken grousers. Longevity testing with identical aluminum wheels on Earth indicates that when three grousers on a given wheel have broken, that wheel has reached about 60 percent of its useful life. Curiosity has driven well over 60 percent of the amount needed for reaching all the geological layers planned as the mission's science destinations, so the start of seeing broken grousers is not expected to affect the mission's operations. Curiosity's six aluminum wheels are about 20 inches (50 centimeters) in diameter and 16 inches (40 centimeters) wide. Each of the six wheels has its own drive motor, and the four corner wheels also have steering motors. http://photojournal.jpl.nasa.gov/catalog/PIA21486

The use of a running wheel to measure activity in rodents: relationship to energy balance, general activity, and reward.

PubMed

Novak, Colleen M; Burghardt, Paul R; Levine, James A

2012-03-01

Running wheels are commonly employed to measure rodent physical activity in a variety of contexts, including studies of energy balance and obesity. There is no consensus on the nature of wheel-running activity or its underlying causes, however. Here, we will begin by systematically reviewing how running wheel availability affects physical activity and other aspects of energy balance in laboratory rodents. While wheel running and physical activity in the absence of a wheel commonly correlate in a general sense, in many specific aspects the two do not correspond. In fact, the presence of running wheels alters several aspects of energy balance, including body weight and composition, food intake, and energy expenditure of activity. We contend that wheel-running activity should be considered a behavior in and of itself, reflecting several underlying behavioral processes in addition to a rodent's general, spontaneous activity. These behavioral processes include defensive behavior, predatory aggression, and depression- and anxiety-like behaviors. As it relates to energy balance, wheel running engages several brain systems-including those related to the stress response, mood, and reward, and those responsive to growth factors-that influence energy balance indirectly. We contend that wheel-running behavior represents factors in addition to rodents' tendency to be physically active, engaging additional neural and physiological mechanisms which can then independently alter energy balance and behavior. Given the impact of wheel-running behavior on numerous overlapping systems that influence behavior and physiology, this review outlines the need for careful design and interpretation of studies that utilize running wheels as a means for exercise or as a measurement of general physical activity. Copyright © 2012 Elsevier Ltd. All rights reserved.

The use of a running wheel to measure activity in rodents: Relationship to energy balance, general activity, and reward

PubMed Central

Levine, James A.

2015-01-01

Running wheels are commonly employed to measure rodent physical activity in a variety of contexts, including studies of energy balance and obesity. There is no consensus on the nature of wheel-running activity or its underlying causes, however. Here, we will begin by systematically reviewing how running wheel availability affects physical activity and other aspects of energy balance in laboratory rodents. While wheel running and physical activity in the absence of a wheel commonly correlate in a general sense, in many specific aspects the two do not correspond. In fact, the presence of running wheels alters several aspects of energy balance, including body weight and composition, food intake, and energy expenditure of activity. We contend that wheel-running activity should be considered a behavior in and of itself, reflecting several underlying behavioral processes in addition to a rodent's general, spontaneous activity. These behavioral processes include defensive behavior, predatory aggression, and depression- and anxiety-like behaviors. As it relates to energy balance, wheel running engages several brain systems—including those related to the stress response, mood, and reward, and those responsive to growth factors—that influence energy balance indirectly. We contend that wheel-running behavior represents factors in addition to rodents' tendency to be physically active, engaging additional neural and physiological mechanisms which can then independently alter energy balance and behavior. Given the impact of wheel-running behavior on numerous overlapping systems that influence behavior and physiology, this review outlines the need for careful design and interpretation of studies that utilize running wheels as a means for exercise or as a measurement of general physical activity. PMID:22230703

Tracked Vehicle Road Wheel Puller

DTIC Science & Technology

2009-02-01

employed for removing smaller-size components, such as bolts and the like. U.S. Patent No. 5,410,792, issued to Freeman (3), discloses a caster wheel ...separation of the rubberized annular layer from the outer annular surface of the wheel . Figure 5 further illustrates a modification of the wheel puller...2001. 2. Rubino et al. Pulling Tool. U.S. Patent 5,479,688, 1996. 3. Freeman. Caster Wheel Axle Extraction Apparatus. U.S. Patent 5,410,792

Nontraditional Machining Guide, 26 Newcomers for Production

DTIC Science & Technology

1976-07-01

essential: Frequent coarse wheel dressing to maintain sharpness Lower wheel speeds (under 3500 sfpm) Lower infeed rates (0.0002 to 0.0005 inch per pass...Oil-base lubricants with good flow control Soft wheels (H, I or J grades) Higher table speeds (50 sfpm or more) Solid fixtures and well...the wheel and the workpiece as in ECG. Electrical discharges from the graphite wheel are initiated from the higher a-c voltage superimposed on

14 CFR Appendix D to Part 23 - Wheel Spin-Up and Spring-Back Loads

Code of Federal Regulations, 2014 CFR

2014-01-01

... (0.80 may be used); F Vmax=maximum vertical force on wheel (pounds)=n j W e, where W e and n j are... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Wheel Spin-Up and Spring-Back Loads D.... D Appendix D to Part 23—Wheel Spin-Up and Spring-Back Loads D23.1 Wheel spin-up loads. (a) The...

14 CFR Appendix D to Part 23 - Wheel Spin-Up and Spring-Back Loads

Code of Federal Regulations, 2013 CFR

2013-01-01

... (0.80 may be used); F Vmax=maximum vertical force on wheel (pounds)=n j W e, where W e and n j are... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Wheel Spin-Up and Spring-Back Loads D.... D Appendix D to Part 23—Wheel Spin-Up and Spring-Back Loads D23.1 Wheel spin-up loads. (a) The...

14 CFR Appendix D to Part 23 - Wheel Spin-Up and Spring-Back Loads

Code of Federal Regulations, 2011 CFR

2011-01-01

... (0.80 may be used); F Vmax=maximum vertical force on wheel (pounds)=n j W e, where W e and n j are... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Wheel Spin-Up and Spring-Back Loads D.... D Appendix D to Part 23—Wheel Spin-Up and Spring-Back Loads D23.1 Wheel spin-up loads. (a) The...

14 CFR Appendix D to Part 23 - Wheel Spin-Up and Spring-Back Loads

Code of Federal Regulations, 2010 CFR

2010-01-01

... (0.80 may be used); F Vmax=maximum vertical force on wheel (pounds)=n j W e, where W e and n j are... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Wheel Spin-Up and Spring-Back Loads D.... D Appendix D to Part 23—Wheel Spin-Up and Spring-Back Loads D23.1 Wheel spin-up loads. (a) The...

14 CFR Appendix D to Part 23 - Wheel Spin-Up and Spring-Back Loads

Code of Federal Regulations, 2012 CFR

2012-01-01

... (0.80 may be used); F Vmax=maximum vertical force on wheel (pounds)=n j W e, where W e and n j are... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Wheel Spin-Up and Spring-Back Loads D.... D Appendix D to Part 23—Wheel Spin-Up and Spring-Back Loads D23.1 Wheel spin-up loads. (a) The...

Wheel/Rail Noise and Vibration : Volume 2. Applications to Control of Wheel/Rail Noise.

DOT National Transportation Integrated Search

1975-05-01

The final reports are reported of a project to develop a basic understanding of urban transit wheel/rail noise control measures. Analytical models of impedance, response, radiation efficiency, and directivity of wheels and rails are presented and com...

Shock-absorbing caster wheel is simple and compact

NASA Technical Reports Server (NTRS)

Kindley, R. J.

1968-01-01

Compact shock-absorbing caster wheel mitigates or absorbs shock by a compressible tire which deforms into a cavity between its inner edge and the wheel hub. A tee-shaped annular ring embedded in the tire distributes loads more uniformly throughout both wheel and tire.

Study on general theory of kinematics and dynamics of wheeled mobile robots

NASA Astrophysics Data System (ADS)

Tsukishima, Takahiro; Sasaki, Ken; Takano, Masaharu; Inoue, Kenji

1992-03-01

This paper proposes a general theory of kinematics and dynamics of wheeled mobile robots (WMRs). Unlike robotic manipulators which are modeled as 3-dimensional serial link mechanism, WMRs will be modeled as planar linkage mechanism with multiple links branching out from the base and/or another link. Since this model resembles a tree with branches, it will be called 'tree-structured-link'. The end of each link corresponds to the wheel which is in contact with the floor. In dynamics of WMR, equation of motion of a WMR is derived from joint input torques incorporating wheel dynamics. The wheel dynamics determines forces and moments acting on wheels as a function of slip velocity. This slippage of wheels is essential in dynamics of WMR. It will also be shown that the dynamics of WMR reduces to kinematics when slippage of wheels is neglected. Furthermore, the equation of dynamics is rewritten in velocity input form, since most of industrial motors are velocity controlled.

A Robust Control of Two-Wheeled Mobile Manipulator with Underactuated Joint by Nonlinear Backstepping Method

NASA Astrophysics Data System (ADS)

Acar, Cihan; Murakami, Toshiyuki

In this paper, a robust control of two-wheeled mobile manipulator with underactuated joint is considered. Two-wheeled mobile manipulators are dynamically balanced two-wheeled driven systems that do not have any caster or extra wheels to stabilize their body. Two-wheeled mobile manipulators mainly have an important feature that makes them more flexible and agile than the statically stable mobile manipulators. However, two-wheeled mobile manipulator is an underactuated system due to its two-wheeled structure. Therefore, it is required to stabilize the underactuated passive body and, at the same time, control the position of the center of gravity (CoG) of the manipulator in this system. To realize this, nonlinear backstepping based control method with virtual double inverted pendulum model is proposed in this paper. Backstepping is used with sliding mode to increase the robustness of the system against modeling errors and other perturbations. Then robust acceleration control is also achieved by utilizing disturbance observer. Performance of the proposed method is evaluated by several experiments.

The Running Wheel Enhances Food Anticipatory Activity: An Exploratory Study

PubMed Central

Flôres, Danilo E. F. L.; Bettilyon, Crystal N.; Jia, Lori; Yamazaki, Shin

2016-01-01

Rodents anticipate rewarding stimuli such as daily meals, mates, and stimulant drugs. When a single meal is provided daily at a fixed time of day, an increase in activity, known as food anticipatory activity (FAA), occurs several hours before feeding time. The factors affecting the expression of FAA have not been well-studied. Understanding these factors may provide clues to the undiscovered anatomical substrates of food entrainment. In this study we determined whether wheel-running activity, which is also rewarding to rodents, modulated the robustness of FAA. We found that access to a freely rotating wheel enhanced the robustness of FAA. This enhancement was lost when the wheel was removed. In addition, while prior exposure to a running wheel alone did not enhance FAA, the presence of a locked wheel did enhance FAA as long as mice had previously run in the wheel. Together, these data suggest that FAA, like wheel-running activity, is influenced by reward signaling. PMID:27458354

Computation of wheel-rail contact force for non-mapping wheel-rail profile of Translohr tram

NASA Astrophysics Data System (ADS)

Ji, Yuanjin; Ren, Lihui; Zhou, Jinsong

2017-09-01

Translohr tram has steel wheels, in V-like arrangements, as guide wheels. These operate over the guide rails in inverted-V arrangements. However, the horizontal and vertical coordinates of the guide wheels and guide rails are not always mapped one-to-one. In this study, a simplified elastic method is proposed in order to calculate the contact points between the wheels and the rails. By transforming the coordinates, the non-mapping geometric relationship between wheel and rail is converted into a mapping relationship. Considering the Translohr tram's multi-point contact between the guide wheel and the guide rail, the elastic-contact hypothesis take into account the existence of contact patches between the bodies, and the location of the contact points is calculated using a simplified elastic method. In order to speed up the calculation, a multi-dimensional contact table is generated, enabling the use of simulation for Translohr tram running on curvatures with different radii.

The Running Wheel Enhances Food Anticipatory Activity: An Exploratory Study.

PubMed

Flôres, Danilo E F L; Bettilyon, Crystal N; Jia, Lori; Yamazaki, Shin

2016-01-01

Rodents anticipate rewarding stimuli such as daily meals, mates, and stimulant drugs. When a single meal is provided daily at a fixed time of day, an increase in activity, known as food anticipatory activity (FAA), occurs several hours before feeding time. The factors affecting the expression of FAA have not been well-studied. Understanding these factors may provide clues to the undiscovered anatomical substrates of food entrainment. In this study we determined whether wheel-running activity, which is also rewarding to rodents, modulated the robustness of FAA. We found that access to a freely rotating wheel enhanced the robustness of FAA. This enhancement was lost when the wheel was removed. In addition, while prior exposure to a running wheel alone did not enhance FAA, the presence of a locked wheel did enhance FAA as long as mice had previously run in the wheel. Together, these data suggest that FAA, like wheel-running activity, is influenced by reward signaling.

The Four-Ball Gyro and Motorcycle Countersteering

NASA Astrophysics Data System (ADS)

Galli, J. Ronald; Carroll, Bradley W.

2017-04-01

Most two-wheel motorcycle riders know that, at highway speeds, if you want to turn left you push on the left handlebar and pull on the right handlebar. This is called countersteering. Countersteering is counterintuitive since pushing left and pulling right when the front wheel is not spinning would turn the wheel to the right. All good motorcycle instructors teach countersteering but few understand the physics of why it works, even though there is considerable discussion about it among motorcycle riders. This paper gives a simplified explanation of gyroscopic precession and then applies this to the front wheel of a motorcycle using two steps: 1) explaining how the wheel's lean is initiated, and 2) explaining how the lean will cause the wheel to turn. To assist with this discussion and to demonstrate the conclusions, a "wheel" was constructed using copper pipe, a bicycle wheel hub, and one pound of lead in each of four "balls" at the end of the spokes (see Fig. 1).

Tuning thermal mismatch between turbine rotor parts with a thermal medium

DOEpatents

Schmidt, Mark Christopher

2001-01-01

In a turbine rotor, an aft shaft wheel and the final-stage wheel of the rotor are coupled together, including by a rabbeted joint. During shutdown and startup of the turbine, a thermal mismatch between the aft shaft wheel and final-stage wheel is avoided by respectively heating and cooling the aft shaft wheel to maintain the thermal mismatch within acceptable limits, thereby avoiding opening of the rabbeted joint and the potential for unbalancing the rotor and rotor vibration. The thermal medium may be supplied by piping in the aft bearing cavity into the cavity between the forward closure plate and the aft shaft wheel.

Innovative grinding wheel design for cost-effective machining of advanced ceramics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Licht, R.H.; Kuo, P.; Liu, S.

2000-05-01

This Final Report covers the Phase II Innovative Grinding Wheel (IGW) program in which Norton Company successfully developed a novel grinding wheel for cost-effective cylindrical grinding of advanced ceramics. In 1995, Norton Company successfully completed the 16-month Phase I technical effort to define requirements, design, develop, and evaluate a next-generation grinding wheel for cost-effective cylindrical grinding of advanced ceramics using small prototype wheels. The Phase II program was initiated to scale-up the new superabrasive wheel specification to larger diameters, 305-mm to 406-mm, required for most production grinding of cylindrical ceramic parts, and to perform in-house and independent validation grinding tests.

Design and jump phenomenon analysis of an eccentric ring energy harvester

NASA Astrophysics Data System (ADS)

Wang, Yu-Jen; Chen, Chung-De

2013-10-01

This paper presents the development of a wheel-mounted eccentric ring energy harvester that is driven by centripetal and gravitational forces during wheel rotation. The natural frequency of the eccentric ring matches the wheel rotation frequency at any car speed because its character length is designed equal to the wheel radius. Consequently, the eccentric ring oscillates with a relatively large swing angle at the wheel speed to generate high levels of power. The nonlinear dynamic behavior of the eccentric ring is investigated to ensure that the proposed design produces steady swing angles, especially at high wheel speeds. Herein, the jump phenomenon of the dynamic motion of the eccentric ring is analyzed by using the Duffing equation and the linearization process. The discriminant value obtained from the analysis confirms that no jump phenomenon occurs at all wheel speeds if the eccentric ring is properly designed. In the experiment, the eccentric ring is integrated with magnets and a coil set to generate 318-442 μW at constant wheel speeds between 300 and 500 rpm. This shows that the proposed device is a potential power source for low-power wheel-mounted electronics, such as pressure sensors, accelerometers, and thermometers.

A bout of voluntary running enhances context conditioned fear, its extinction, and its reconsolidation

PubMed Central

Siette, Joyce; Reichelt, Amy C.; Westbrook, R. Frederick

2014-01-01

Three experiments used rats to examine the effect of a single bout of voluntary activity (wheel running) on the acquisition, extinction, and reconsolidation of context conditioned fear. In Experiment 1, rats provided with access to a wheel for 3 h immediately before or after a shocked exposure to a context froze more when tested in that context than rats provided with access to the wheels 6 h after the shocked exposure or rats not provided with access to the wheels. In Experiment 2, rats provided with access to the wheels immediately before or after a nonshocked exposure to the conditioned context froze less when tested in that context than rats provided with access to the wheels 6 h after the nonshocked exposure or rats not provided with access to the wheels. In Experiment 3, rats provided with access to wheels immediately after an extended nonshocked exposure to the conditioned context again froze less, whereas rats provided with access to the wheels after a brief nonshocked exposure froze more on the subsequent test than sedentary controls. These results show that a single bout of running can enhance acquisition, extinction, and reconsolidation of context conditioned fear. PMID:24429425

Wheelchair users' perceptions of and experiences with power assist wheels.

PubMed

Giacobbi, Peter R; Levy, Charles E; Dietrich, Frederick D; Winkler, Sandra Hubbard; Tillman, Mark D; Chow, John W

2010-03-01

To assess wheelchair users' perceptions of and experiences with power assist wheels using qualitative interview methods. Qualitative evaluations were conducted in a laboratory setting with a focus on users' experiences using power assist wheel in their naturalistic environments. Participants consisted of seven women and 13 men (M(age) = 42.75, SD = 14.68) that included one African American, one Hispanic, 17 whites, and one individual from Zambia. Qualitative interviews were conducted before, during, and after use of a power assist wheel. Main outcome measures included the wheelchair users' evaluations and experiences related to the use of power assist wheels. The primary evaluations included wheeling on challenging terrains, performance of novel activities, social/family aspects, fatigue, and pain. These descriptions indicated that most participants perceived positive experiences with the power assist wheels, including access to new and different activities. Secondary evaluations indicated that the unit was cumbersome and prohibitive for some participants because of difficulties with transport in and out of a vehicle and battery life. Most participants felt that power assist wheels provided more independence and social opportunities. The power assist wheel seems to offer physical and social benefits for most wheelers. Clinicians should consider users' home environment and overall life circumstances before prescribing.

A bout of voluntary running enhances context conditioned fear, its extinction, and its reconsolidation.

PubMed

Siette, Joyce; Reichelt, Amy C; Westbrook, R Frederick

2014-01-15

Three experiments used rats to examine the effect of a single bout of voluntary activity (wheel running) on the acquisition, extinction, and reconsolidation of context conditioned fear. In Experiment 1, rats provided with access to a wheel for 3 h immediately before or after a shocked exposure to a context froze more when tested in that context than rats provided with access to the wheels 6 h after the shocked exposure or rats not provided with access to the wheels. In Experiment 2, rats provided with access to the wheels immediately before or after a nonshocked exposure to the conditioned context froze less when tested in that context than rats provided with access to the wheels 6 h after the nonshocked exposure or rats not provided with access to the wheels. In Experiment 3, rats provided with access to wheels immediately after an extended nonshocked exposure to the conditioned context again froze less, whereas rats provided with access to the wheels after a brief nonshocked exposure froze more on the subsequent test than sedentary controls. These results show that a single bout of running can enhance acquisition, extinction, and reconsolidation of context conditioned fear.

Conditioned taste avoidance induced by forced and voluntary wheel running in rats.

PubMed

Forristall, J R; Hookey, B L; Grant, V L

2007-03-01

Voluntary exercise by rats running in a freely rotating wheel (free wheel) produces conditioned taste avoidance (CTA) of a flavored solution consumed before running [e.g., Lett, B.T., Grant, V.L., 1996. Wheel running induces conditioned taste aversion in rats trained while hungry and thirsty. Physiol. Behav. 59, 699-702]. Forced exercise, swimming or running, also produces CTA in rats [e.g., Masaki, T., Nakajima, S., 2006. Taste aversion induced by forced swimming, voluntary running, forced running, and lithium chloride injection treatments. Physiol. Behav. 88, 411-416]. Energy expenditure may be the critical factor in producing such CTA. If so, forced running in a motorized running wheel should produce CTA equivalent to that produced by a similar amount of voluntary running. In two experiments, we compared forced running in a motorized wheel with voluntary running in a free wheel. Mean distance run over 30 min was equated as closely as possible in the two apparatuses. Both types of exercise produced CTA relative to sedentary, locked-wheel controls. However, voluntary running produced greater CTA than forced running. We consider differences between running in the free and motorized wheels that may account for the differences in strength of CTA.

Nesting behavior of house mice (Mus domesticus) selected for increased wheel-running activity.

PubMed

Carter, P A; Swallow, J G; Davis, S J; Garland, T

2000-03-01

Nest building was measured in "active" (housed with access to running wheels) and "sedentary" (without wheel access) mice (Mus domesticus) from four replicate lines selected for 10 generations for high voluntary wheel-running behavior, and from four randombred control lines. Based on previous studies of mice bidirectionally selected for thermoregulatory nest building, it was hypothesized that nest building would show a negative correlated response to selection on wheel-running. Such a response could constrain the evolution of high voluntary activity because nesting has also been shown to be positively genetically correlated with successful production of weaned pups. With wheel access, selected mice of both sexes built significantly smaller nests than did control mice. Without wheel access, selected females also built significantly smaller nests than did control females, but only when body mass was excluded from the statistical model, suggesting that body mass mediated this correlated response to selection. Total distance run and mean running speed on wheels was significantly higher in selected mice than in controls, but no differences in amount of time spent running were measured, indicating a complex cause of the response of nesting to selection for voluntary wheel running.

The Development of Wheels for the Lunar Roving Vehicle

NASA Technical Reports Server (NTRS)

Asnani, Vivake; Delap, Damon; Creager, Colin

2009-01-01

The Lunar Roving Vehicle (LRV) was developed for NASA s Apollo program so astronauts could cover a greater range on the lunar surface, carry more science instruments, and return more soil and rock samples than by foot. Because of the unique lunar environment, the creation of flexible wheels was the most challenging and time consuming aspect of the LRV development. Wheels developed for previous lunar systems were not sufficient for use with this manned vehicle; therefore, several new designs were created and tested. Based on criteria set by NASA, the choices were narrowed down to two: the wire mesh wheel developed by General Motors (GM), and the hoop spring wheel developed by the Bendix Corporation. Each of these underwent intensive mechanical, material, and terramechanical analyses, and in the end, the wire mesh wheel was chosen for the LRV. Though the wire mesh wheel was determined to be the best choice for its particular application, it may be insufficient towards achieving the objectives of future lunar missions that could require higher tractive capability, increased weight capacity, or extended life. Therefore lessons learned from the original LRV wheel development and suggestions for future Moon wheel projects are offered.

49 CFR 533.5 - Requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... per gallon, in the model year specified as applicable: Table I Model year 2-wheel drive light trucks Captive imports Other 4-wheel drive light trucks Captive imports Other Limited product line light trucks... standard Captive imports Others 2-wheel drive light trucks Captive imports Others 4-wheel drive light...

49 CFR 533.5 - Requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... per gallon, in the model year specified as applicable: Table I Model year 2-wheel drive light trucks Captive imports Other 4-wheel drive light trucks Captive imports Other Limited product line light trucks... standard Captive imports Others 2-wheel drive light trucks Captive imports Others 4-wheel drive light...

49 CFR 533.5 - Requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... per gallon, in the model year specified as applicable: Table I Model year 2-wheel drive light trucks Captive imports Other 4-wheel drive light trucks Captive imports Other Limited product line light trucks... standard Captive imports Others 2-wheel drive light trucks Captive imports Others 4-wheel drive light...

77 FR 27249 - Certain Steel Wheels From China

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-09

... Steel Wheels From China Determinations On the basis of the record \\1\\ developed in the subject... of certain steel wheels from China, provided for in subheading 8708.70 of the Harmonized Tariff... preliminary determinations by Commerce that imports of certain steel wheels from China were subsidized within...

14 CFR 29.483 - One-wheel landing conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false One-wheel landing conditions. 29.483 Section 29.483 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... One-wheel landing conditions. For the one-wheel landing condition, the rotorcraft is assumed to be in...

14 CFR 27.483 - One-wheel landing conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false One-wheel landing conditions. 27.483 Section 27.483 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... One-wheel landing conditions. For the one-wheel landing condition, the rotorcraft is assumed to be in...

14 CFR 27.483 - One-wheel landing conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false One-wheel landing conditions. 27.483 Section 27.483 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... One-wheel landing conditions. For the one-wheel landing condition, the rotorcraft is assumed to be in...

14 CFR 29.483 - One-wheel landing conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false One-wheel landing conditions. 29.483 Section 29.483 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... One-wheel landing conditions. For the one-wheel landing condition, the rotorcraft is assumed to be in...

16 CFR 1512.12 - Requirements for wheel hubs.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Requirements for wheel hubs. 1512.12 Section... REGULATIONS REQUIREMENTS FOR BICYCLES Regulations § 1512.12 Requirements for wheel hubs. All bicycles (other than sidewalk bicycles) shall meet the following requirements: (a) Locking devices. Wheels shall be...

16 CFR 1512.12 - Requirements for wheel hubs.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Requirements for wheel hubs. 1512.12 Section... REGULATIONS REQUIREMENTS FOR BICYCLES Regulations § 1512.12 Requirements for wheel hubs. All bicycles (other than sidewalk bicycles) shall meet the following requirements: (a) Locking devices. Wheels shall be...

Circulating levels of endocannabinoids respond acutely to voluntary exercise, are altered in mice selectively bred for high voluntary wheel running, and differ between the sexes

PubMed Central

Thompson, Zoe; Argueta, Donovan; Garland, Theodore; DiPatrizio, Nicholas

2017-01-01

The endocannabinoid system serves many physiological roles, including in the regulation of energy balance, food reward, and voluntary locomotion. Signaling at the cannabinoid type 1 receptor has been specifically implicated in motivation for rodent voluntary exercise on wheels. We studied four replicate lines of high runner (HR) mice that have been selectively bred for 81 generations based on average number of wheel revolutions on days five and six of a six-day period of wheel access. Four additional replicate lines are bred without regard to wheel running, and serve as controls (C) for random genetic effects that may cause divergence among lines. On average, mice from HR lines voluntarily run on wheels three times more than C mice on a daily basis. We tested the general hypothesis that circulating levels of endocannabinoids (i.e., 2-arachidonoylglycerol [2-AG] and anandamide [AEA]) differ between HR and C mice in a sex-specific manner. Fifty male and 50 female mice were allowed access to wheels for six days, while another 50 males and 50 females were kept without access to wheels (half HR, half C for all groups). Blood was collected by cardiac puncture during the time of peak running on the sixth night of wheel access or no wheel access, and later analyzed for 2-AG and AEA content by ultra-performance liquid chromatography coupled to tandem mass spectrometry. We observed a significant three-way interaction among sex, linetype, and wheel access for 2-AG concentrations, with females generally having lower levels than males and wheel access lowering 2-AG levels in some but not all subgroups. The number of wheel revolutions in the minutes or hours immediately prior to sampling did not quantitatively predict plasma 2-AG levels within groups. We also observed a trend for a linetype-by-wheel access interaction for AEA levels, with wheel access lowering plasma concentrations of AEA in HR mice, while raising them in C mice. In addition, females tended to have higher AEA concentrations than males. For mice housed with wheels, the amount of running during the 30 minutes before sampling was a significant positive predictor of plasma AEA within groups, and HR mice had significantly lower levels of AEA than C mice. Our results suggest that voluntary exercise alters circulating levels of endocannabinoids, and further demonstrate that selective breeding for voluntary exercise is associated with evolutionary changes in the endocannabinoid system. PMID:28017680

Circulating levels of endocannabinoids respond acutely to voluntary exercise, are altered in mice selectively bred for high voluntary wheel running, and differ between the sexes.

PubMed

Thompson, Zoe; Argueta, Donovan; Garland, Theodore; DiPatrizio, Nicholas

2017-03-01

The endocannabinoid system serves many physiological roles, including in the regulation of energy balance, food reward, and voluntary locomotion. Signaling at the cannabinoid type 1 receptor has been specifically implicated in motivation for rodent voluntary exercise on wheels. We studied four replicate lines of high runner (HR) mice that have been selectively bred for 81 generations based on average number of wheel revolutions on days five and six of a six-day period of wheel access. Four additional replicate lines are bred without regard to wheel running, and serve as controls (C) for random genetic effects that may cause divergence among lines. On average, mice from HR lines voluntarily run on wheels three times more than C mice on a daily basis. We tested the general hypothesis that circulating levels of endocannabinoids (i.e., 2-arachidonoylglycerol [2-AG] and anandamide [AEA]) differ between HR and C mice in a sex-specific manner. Fifty male and 50 female mice were allowed access to wheels for six days, while another 50 males and 50 females were kept without access to wheels (half HR, half C for all groups). Blood was collected by cardiac puncture during the time of peak running on the sixth night of wheel access or no wheel access, and later analyzed for 2-AG and AEA content by ultra-performance liquid chromatography coupled to tandem mass spectrometry. We observed a significant three-way interaction among sex, linetype, and wheel access for 2-AG concentrations, with females generally having lower levels than males and wheel access lowering 2-AG levels in some but not all subgroups. The number of wheel revolutions in the minutes or hours immediately prior to sampling did not quantitatively predict plasma 2-AG levels within groups. We also observed a trend for a linetype-by-wheel access interaction for AEA levels, with wheel access lowering plasma concentrations of AEA in HR mice, while raising them in C mice. In addition, females tended to have higher AEA concentrations than males. For mice housed with wheels, the amount of running during the 30min before sampling was a significant positive predictor of plasma AEA within groups, and HR mice had significantly lower levels of AEA than C mice. Our results suggest that voluntary exercise alters circulating levels of endocannabinoids, and further demonstrate that selective breeding for voluntary exercise is associated with evolutionary changes in the endocannabinoid system. Copyright © 2016 Elsevier Inc. All rights reserved.

Procedures for One-Pass Vehicle Cone Index (VCI1) Determination for Acquisition Support

DTIC Science & Technology

2013-08-01

the VCI of tracked vehicles can be directly compared to that of wheeled vehicles; Priddy and Willoughby, 2006). Measurement of the minimum soil...of the wheel , or number of revolutions per unit time divided by 2π for a track v = forward velocity of vehicle or wheel axle. 12. Trafficability...be tested at the expected gross vehicle weight (GVW) and, for wheeled vehicles, at an appropriate soft-soil tire pressure. For wheeled vehicles

Global Versus Reactive Navigation for Joint UAV-UGV Missions in a Cluttered Environment

DTIC Science & Technology

2012-06-01

spaces. The vehicle uses a two- wheel 5 differential drive system with a third omnidirectional caster for balance. This uncomplicated system saves... wheels , two differential drive wheels and one omni- directional caster wheel . The vehicle changes the direction of its movement by altering the speed of...Virtual Speed Versus Time..........64  Figure 23:  Heading and Yaw Rate Versus Time................64  Figure 24:  Individual Wheel Speeds Versus Time

Prediction Study on Anti-Slide Control of Railway Vehicle Based on RBF Neural Networks

NASA Astrophysics Data System (ADS)

Yang, Lijun; Zhang, Jimin

While railway vehicle braking, Anti-slide control system will detect operating status of each wheel-sets e.g. speed difference and deceleration etc. Once the detected value on some wheel-set is over pre-defined threshold, brake effort on such wheel-set will be adjusted automatically to avoid blocking. Such method takes effect on guarantee safety operation of vehicle and avoid wheel-set flatness, however it cannot adapt itself to the rail adhesion variation. While wheel-sets slide, the operating status is chaotic time series with certain law, and can be predicted with the law and experiment data in certain time. The predicted values can be used as the input reference signals of vehicle anti-slide control system, to judge and control the slide status of wheel-sets. In this article, the RBF neural networks is taken to predict wheel-set slide status in multi-step with weight vector adjusted based on online self-adaptive algorithm, and the center & normalizing parameters of active function of the hidden unit of RBF neural networks' hidden layer computed with K-means clustering algorithm. With multi-step prediction simulation, the predicted signal with appropriate precision can be used by anti-slide system to trace actively and adjust wheel-set slide tendency, so as to adapt to wheel-rail adhesion variation and reduce the risk of wheel-set blocking.

Method for controlling a vehicle with two or more independently steered wheels

DOEpatents

Reister, David B.; Unseren, Michael A.

1995-01-01

A method (10) for independently controlling each steerable drive wheel (W.sub.i) of a vehicle with two or more such wheels (W.sub.i). An instantaneous center of rotation target (ICR) and a tangential velocity target (v.sup.G) are inputs to a wheel target system (30) which sends the velocity target (v.sub.i.sup.G) and a steering angle target (.theta..sub.i.sup.G) for each drive wheel (W.sub.i) to a pseudovelocity target system (32). The pseudovelocity target system (32) determines a pseudovelocity target (v.sub.P.sup.G) which is compared to a current pseudovelocity (v.sub.P.sup.m) to determine a pseudovelocity error (.epsilon.). The steering angle targets (.theta..sup.G) and the steering angles (.theta..sup.m) are inputs to a steering angle control system (34) which outputs to the steering angle encoders (36), which measure the steering angles (.theta..sup.m). The pseudovelocity error (.epsilon.), the rate of change of the pseudovelocity error ( ), and the wheel slip between each pair of drive wheels (W.sub.i) are used to calculate intermediate control variables which, along with the steering angle targets (.theta..sup.G) are used to calculate the torque to be applied at each wheel (W.sub.i). The current distance traveled for each wheel (W.sub.i) is then calculated. The current wheel velocities (v.sup.m) and steering angle targets (.theta..sup.G) are used to calculate the cumulative and instantaneous wheel slip (e, ) and the current pseudovelocity (v.sub.P.sup.m).

Enthalpy Distributions of Arc Jet Flow Based on Measured Laser Induced Fluorescence, Heat Flux and Stagnation Pressure Distributions

NASA Technical Reports Server (NTRS)

Suess, Leonard E.; Milhoan, James D.; Oelke, Lance; Godfrey, Dennis; Larin, Maksim Y.; Scott, Carl D.; Grinstead, Jay H.; DelPapa, Steven

2011-01-01

The centerline total enthalpy of arc jet flow is determined using laser induced fluorescence of oxygen and nitrogen atoms. Each component of the energy, kinetic, thermal, and chemical can be determined from LIF measurements. Additionally, enthalpy distributions are inferred from heat flux and pressure probe distribution measurements using an engineering formula. Average enthalpies are determined by integration over the radius of the jet flow, assuming constant mass flux and a mass flux distribution estimated from computational fluid dynamics calculations at similar arc jet conditions. The trends show favorable agreement, but there is an uncertainty that relates to the multiple individual measurements and assumptions inherent in LIF measurements.

In-Service Performance and Costs of Methods for Control of Urban Rail System Noise : Experimental Design

DOT National Transportation Integrated Search

1976-05-01

This report presents an experimental design for a project to evaluate four techniques for reducing wheel-rail noise on urban rail transit systems: (a) resilient wheels, (b) damped wheels, (c) wheel truing, and (d) rail griding. The design presents th...

29 CFR 1910.241 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... reinforced does not cover wheels using such mechanical additions as steel rings, steel cup backs or wire or tape winding. (8) Type 11 flaring cup wheels. Type 11 flaring cup wheels have double diameter... mounting listed for Type 6 straight sided cup wheels definition in subparagraph (9) of this paragraph. Type...

29 CFR 1910.241 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... reinforced does not cover wheels using such mechanical additions as steel rings, steel cup backs or wire or tape winding. (8) Type 11 flaring cup wheels. Type 11 flaring cup wheels have double diameter... mounting listed for Type 6 straight sided cup wheels definition in subparagraph (9) of this paragraph. Type...

Auto Mechanics I. Learning Activity Packets (LAPs). Section D--Suspension.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This document contains six learning activity packets (LAPs) that outline the study activities for the "suspension" instructional area for an Auto Mechanics I course. The six LAPs cover the following topics: wheel bearings, tires and wheels, wheel balancing, suspension system, steering system, and wheel alignment. Each LAP contains a…

40 CFR 86.235-94 - Dynamometer procedure.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., carbon dioxide, and oxides of nitrogen. (b) As long as an emission sample is not taken, practice runs...) Four-wheel drive vehicles will be tested in a two-wheel drive mode of operation. Full-time four-wheel drive vehicles will have one set of drive wheels temporarily disengaged by the vehicle manufacturer...

16 CFR § 1512.12 - Requirements for wheel hubs.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Requirements for wheel hubs. § 1512.12... ACT REGULATIONS REQUIREMENTS FOR BICYCLES Regulations § 1512.12 Requirements for wheel hubs. All bicycles (other than sidewalk bicycles) shall meet the following requirements: (a) Locking devices. Wheels...

14 CFR 29.479 - Level landing conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... accelerate the wheel rolling assembly up to the specified ground speed, with— (i) The ground speed for... which each wheel contacts the ground simultaneously. (2) An attitude in which the aft wheels contact the ground with the forward wheels just clear of the ground. (b) Loading conditions. The rotorcraft must be...

14 CFR 29.479 - Level landing conditions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... accelerate the wheel rolling assembly up to the specified ground speed, with— (i) The ground speed for... which each wheel contacts the ground simultaneously. (2) An attitude in which the aft wheels contact the ground with the forward wheels just clear of the ground. (b) Loading conditions. The rotorcraft must be...

The Planning Wheel: Value Added Performance.

ERIC Educational Resources Information Center

Murk, Peter J.; Walls, Jeffrey L.

The "Planning Wheel" is an evolution of the original Systems Approach Model (SAM) that was introduced in 1986 by Murk and Galbraith. Unlike most current planning models, which are linear in design and concept, the Planning Wheel bridges the gap between linear and nonlinear processes. The "Program Planning Wheel" is designed to…

A hybrid air conditioner driven by a hybrid solar collector

NASA Astrophysics Data System (ADS)

Al-Alili, Ali

The objective of this thesis is to search for an efficient way of utilizing solar energy in air conditioning applications. The current solar Air Conditioners (A/C)s suffer from low Coefficient of Performance (COP) and performance degradation in hot and humid climates. By investigating the possible ways of utilizing solar energy in air conditioning applications, the bottlenecks in these approaches were identified. That resulted in proposing a novel system whose subsystem synergy led to a COP higher than unity. The proposed system was found to maintain indoor comfort at a higher COP compared to the most common solar A/Cs, especially under very hot and humid climate conditions. The novelty of the proposed A/C is to use a concentrating photovoltaic/thermal collector, which outputs thermal and electrical energy simultaneously, to drive a hybrid A/C. The performance of the hybrid A/C, which consists of a desiccant wheel, an enthalpy wheel, and a vapor compression cycle (VCC), was investigated experimentally. This work also explored the use of a new type of desiccant material, which can be regenerated with a low temperature heat source. The experimental results showed that the hybrid A/C is more effective than the standalone VCC in maintaining the indoor conditions within the comfort zone. Using the experimental data, the COP of the hybrid A/C driven by a hybrid solar collector was found to be at least double that of the current solar A/Cs. The innovative integration of its subsystems allows each subsystem to do what it can do best. That leads to lower energy consumption which helps reduce the peak electrical loads on electric utilities and reduces the consumer operating cost since less energy is purchased during the on peak periods and less solar collector area is needed. In order for the proposed A/C to become a real alternative to conventional systems, its performance and total cost were optimized using the experimentally validated model. The results showed that for an electricity price of 0.12 $/kW-hr, the hybrid solar A/C's cumulative total cost will be less than that of a standard VCC after 17.5 years of operation.

Substituent and ring effects on enthalpies of formation: 2-methyl- and 2-ethylbenzimidazoles versus benzene- and imidazole-derivatives

NASA Astrophysics Data System (ADS)

Jiménez, Pilar; Roux, María Victoria; Dávalos, Juan Z.; Temprado, Manuel; Ribeiro da Silva, Manuel A. V.; Ribeiro da Silva, Maria Das Dores M. C.; Amaral, Luísa M. P. F.; Cabildo, Pilar; Claramunt, Rosa M.; Mó, Otilia; Yáñez, Manuel; Elguero, José

The enthalpies of combustion, heat capacities, enthalpies of sublimation and enthalpies of formation of 2-methylbenzimidazole (2MeBIM) and 2-ethylbenzimidazole (2EtBIM) are reported and the results compared with those of benzimidazole itself (BIM). Theoretical estimates of the enthalpies of formation were obtained through the use of atom equivalent schemes. The necessary energies were obtained in single-point calculations at the B3LYP/6-311+G(d,p) on B3LYP/6-31G* optimized geometries. The comparison of experimental and calculated values of benzenes, imidazoles and benzimidazoles bearing H (unsubstituted), methyl and ethyl groups shows remarkable homogeneity. The energetic group contribution transferability is not followed, but either using it or adding an empirical interaction term, it is possible to generate an enormous collection of reasonably accurate data for different substituted heterocycles (pyrazole-derivatives, pyridine-derivatives, etc.) from the large amount of values available for substituted benzenes and those of the parent (pyrazole, pyridine) heterocycles.

Enthalpy-based equation of state for highly porous materials employing modified soft sphere fluid model

NASA Astrophysics Data System (ADS)

Nayak, Bishnupriya; Menon, S. V. G.

2018-01-01

Enthalpy-based equation of state based on a modified soft sphere model for the fluid phase, which includes vaporization and ionization effects, is formulated for highly porous materials. Earlier developments and applications of enthalpy-based approach had not accounted for the fact that shocked states of materials with high porosity (e.g., porosity more than two for Cu) are in the expanded fluid region. We supplement the well known soft sphere model with a generalized Lennard-Jones formula for the zero temperature isotherm, with parameters determined from cohesive energy, specific volume and bulk modulus of the solid at normal condition. Specific heats at constant pressure, ionic and electronic enthalpy parameters and thermal excitation effects are calculated using the modified approach and used in the enthalpy-based equation of state. We also incorporate energy loss from the shock due to expansion of shocked material in calculating porous Hugoniot. Results obtained for Cu, even up to initial porosities ten, show good agreement with experimental data.

Enthalpy characteristics of L-proline dissolution in certain water-organic mixtures at 298.15 K

NASA Astrophysics Data System (ADS)

Badelin, V. G.; Smirnov, V. I.

2017-01-01

A thermochemical study of the processes of L-proline dissolution in aqueous solutions of acetonitrile, 1,4-dioxane, acetone, dimethyl sulfoxide, nitromethane and tetrahydrofuran at T = 298.15 K in the range of organic solvent concentrations x2 = 0-0.25 mole fractions is performed. Standard values of the enthalpies of solution and transfer of L-proline from water to mixed solvent, and the enthalpy coefficients of pairwise interactions between L-proline and molecules of organic solvents, are calculated. The effect the composition of a water-organic mixture and the structure of organic solvents have on the enthalpy characteristics of L-proline dissolution and transfer is examined. The effect the energy properties of intermolecular interactions between components of a mixed solvent has on the intermolecular interactions between L-proline and molecules of cosolvent is estimated. The correlation between the enthalpy characteristics of L-proline dissolution and electron-donor properties of organic cosolvent in aqueous solutions is determined.

Effects of water-alcohol binary solvents on the thermochemical characteristics of L-tryptophane dissolution at 298.15 K

NASA Astrophysics Data System (ADS)

Badelin, V. G.; Smirnov, V. I.

2013-01-01

The enthalpies of L-tryptophane solution in water-methanol, water-ethanol, water-1-propanol, and water-2-propanol mixtures at alcohol concentrations of x 2 = 0-0.4 mole fractions were measured by calorimetry. The standard enthalpies of L-tryptophane solution (Δsol H ∘) and transfer (Δtr H ∘) from water to the binary solvent were calculated. The influence of the composition of the water-alcohol mixture and the structure and properties of L-tryptophane on the enthalpy characteristics of the latter was considered. The enthalpy coefficients of pair interactions ( h xy ) of L-tryptophane with alcohol molecules were calculated. The coefficients were positive and increased in the series: methanol (MeOH), ethanol (EtOH), 1-propanol (1-PrOH), and 2-propanol (2-PrOH). The solution and transfer enthalpies of L-tryptophane were compared with those of aliphatic amino acids (glycine, L-threonine, DL-alanine, L-valine, and L-phenylalanine) in similar binary solvents.

Thermodynamic Parameters of the Dissolution of 4-Hydroxy-L-Proline and L-Phenylalanine in Mixed Aqueous Solvents at 298 K

NASA Astrophysics Data System (ADS)

Smirnov, V. I.; Badelin, V. G.

2018-01-01

The enthalpies of solution of 4-hydroxy-L-proline and L-phenylalanine in binary mixed aqueous solvents containing acetonitrile (AN), 1,4-dioxane (1,4-DO), or acetone (AC) at mole fractions of 0 to 0.25 are determined at T = 298.15 K via isothermal calorimetry. The standard enthalpies of solution (Δsol H°) and transfer (Δtr H°) of 4-hydroxy-L-proline and L-phenylalanine from water to mixed aqueous solvents are calculated using the experimental calorimetric data, as are the enthalpy coefficients of paired interactions ( h xy ) between the molecules of the investigated amino acids and the organic solvents. The effects the mixed aqueous solvent composition and the structure of the organic solvent molecules have on the enthalpies of solution and transfer for the investigated amino acids are considered. The correlation between the enthalpy of solution of the amino acids and the electron-donating properties of the organic solvents in the mixed aqueous solvent systems is established.

Characterization Parameters for a Three Degree of Freedom Mobile Robot

DTIC Science & Technology

2013-12-01

DARc’s dimensions which contributed to the inertia, force, torque and position equa- tions. We calculated body inertia as 1.93kg·m2 and wheel inertia...separation .316 Wheel Radius Outer/Inner .127 m .085cm Wheel Mass .7055 kg Body Mass 13.542 kg Table 4.1: DAR-C Dimensions The force on each wheel...which used ackeman steering, a technique where wheels are able to rotate relative the robot body . The easiest example of a differentially steered

Orbit Transfer Rocket Engine Technology Program. Automated Preflight Methods Concept Definition. Task E.7

DTIC Science & Technology

1991-12-21

itself. For example, in the case of turbine wheel /blade inspection, remotely obtained blade fatigue data coupled with a life prediction model and...Security, etc. C 2. T/C Assembly for Evidence of Coolant Passage Blockage C 3. HPFTP Turbine Wheel /Blades for Cracks, Fatigue and Damage C 4. HPOTP Turbine... Wheel /Blades for Cracks, Fatigue and Damage C 5. LPFTP Turbine Wheel /Blades for Cracks, Fatigue and Damage C 6. LPOTP Turbine Wheel /Blades for Cracks

Enthalpy relaxation studies of two structurally related amorphous drugs and their binary dispersions.

PubMed

Bansal, Shyam Sunder; Kaushal, Aditya Mohan; Bansal, Arvind Kumar

2010-11-01

The purpose of the current study was to evaluate the enthalpy relaxation behavior of valdecoxib (VLB) and etoricoxib (ETB) and their binary dispersions to derive relaxation constants and to understand their molecular mobilities. Solid dispersions of VLB and ETB were prepared with 1%, 2%, 5%, 10%, 15%, and 20% (w/w) concentrations of polyvinylpyrrolidone (PVP) in situ using differential scanning calorimetry (DSC). Enthalpy relaxation studies were carried out with isothermal storage periods of 1, 2, 4, 6, 16, and 24 hours at 40°C and 0% relative humidity (RH). PVP increased the glass transition temperature (T(g)) and decreased the enthalpy relaxation. Significant differences between two drugs were observed with respect to their relaxation behavior which may be due to differences in intermolecular interactions as predicted by Couchman-Karasz equation and molecular mobility. Kohlrausch-Williams-Watts equation was found to be inadequate in describing complex molecular relaxations in binary dispersions. The enthalpy relaxation behavior of VLB and ETB was found to be significantly different. PVP stabilized VLB significantly; however, its effect on ETB was negligible. The extent of enthalpy relaxation was found to correlate with hydrogen bonding tendency of the drug molecules. The outcome can help in rational designing of amorphous systems with optimal performance.

Formation enthalpies for transition metal alloys using machine learning

NASA Astrophysics Data System (ADS)

Ubaru, Shashanka; Miedlar, Agnieszka; Saad, Yousef; Chelikowsky, James R.

2017-06-01

The enthalpy of formation is an important thermodynamic property. Developing fast and accurate methods for its prediction is of practical interest in a variety of applications. Material informatics techniques based on machine learning have recently been introduced in the literature as an inexpensive means of exploiting materials data, and can be used to examine a variety of thermodynamics properties. We investigate the use of such machine learning tools for predicting the formation enthalpies of binary intermetallic compounds that contain at least one transition metal. We consider certain easily available properties of the constituting elements complemented by some basic properties of the compounds, to predict the formation enthalpies. We show how choosing these properties (input features) based on a literature study (using prior physics knowledge) seems to outperform machine learning based feature selection methods such as sensitivity analysis and LASSO (least absolute shrinkage and selection operator) based methods. A nonlinear kernel based support vector regression method is employed to perform the predictions. The predictive ability of our model is illustrated via several experiments on a dataset containing 648 binary alloys. We train and validate the model using the formation enthalpies calculated using a model by Miedema, which is a popular semiempirical model used for the prediction of formation enthalpies of metal alloys.

Calorimetric determination of the enthalpy of 1-butyl-3-methylimidazolium bromide synthesis: a key quantity in thermodynamics of ionic liquids.

PubMed

Paulechka, Yauheni U; Kabo, Andrey G; Blokhin, Andrey V

2009-11-05

The enthalpy of the 1-butyl-3-methylimidazolium bromide [C(4)mim]Br ionic liquid synthesis reaction 1-methylimidazole (liq) + 1-bromobutane (liq) --> [C(4)mim]Br (liq) was determined in a homemade small-volume isoperibol calorimeter to be Delta(r)H degrees (298) = -87.7 +/- 1.6 kJ x mol(-1). The activation energy for this reaction in a homogeneous system E(A) = 73 +/- 4 kJ x mol(-1) was found from the results of calorimetric measurements. The formation enthalpies for the crystalline and liquid [C(4)mim]Br were determined from the calorimetric data: Delta(f)H degrees (298)(cr) = -178 +/- 5 kJ x mol(-1) and Delta(f)H degrees (298)(liq) = -158 +/- 5 kJ x mol(-1). The ideal-gas formation enthalpy of this compound Delta(f)H degrees (298)(g) = 16 +/- 7 kJ x mol(-1) was calculated using the methods of quantum chemistry and statistical thermodynamics. The vaporization enthalpy of [C(4)mim]Br, Delta(vap)H degrees (298) = 174 +/- 9 kJ x mol(-1), was estimated from the experimental and calculated formation enthalpies. It was demonstrated that vapor pressure of this ionic liquid cannot be experimentally determined.

Calorimetric and computational study of indanones.

PubMed

Matos, M Agostinha R; Miranda, Margarida S; Monte, Manuel J S; Santos, Luís M N B F; Morais, Victor M F; Chickos, James S; Umnahanant, Patamaporn; Liebman, Joel F

2007-11-01

Condensed phase standard (p degrees = 0.1 MPa) molar enthalpies of formation for 1-indanone, 2-indanone, and 1,3-indandione were derived from the standard molar enthalpies of combustion, in oxygen, at T = 298.15 K, measured by static bomb combustion calorimetry. The standard molar enthalpies of sublimation for 1-indanone and 2-indanone, at T = 298.15 K, were measured both by correlation-gas chromatography and by Calvet microcalorimetry leading to a mean value for each compound. For 1,3-indandione, the standard molar enthalpy of sublimation was derived from the vapor pressure dependence on temperature. The following enthalpies of formation in gas phase, at T = 298.15 K, were then derived: 1-indanone, -64.0 +/- 3.8 kJ mol(-1); 2-indanone, -56.6 +/- 4.8 kJ mol(-1); 1,3-indandione, -165.0 +/- 2.6 kJ mol(-1). The vaporization and fusion enthalpies of the indanones studied are also reported. In addition, theoretical calculations using the density functional theory with the B3LYP and MPW1B95 energy functionals and the 6-311G** and cc-pVTZ basis sets have been performed for these molecules and the corresponding one-ring species to obtain the most stable geometries and to access their energetic stabilities.

Design and optimisation of wheel-rail profiles for adhesion improvement

NASA Astrophysics Data System (ADS)

Liu, B.; Mei, T. X.; Bruni, S.

2016-03-01

This paper describes a study for the optimisation of the wheel profile in the wheel-rail system to increase the overall level of adhesion available at the contact interface, in particular to investigate how the wheel and rail profile combination may be designed to ensure the improved delivery of tractive/braking forces even in poor contact conditions. The research focuses on the geometric combination of both wheel and rail profiles to establish how the contact interface may be optimised to increase the adhesion level, but also to investigate how the change in the property of the contact mechanics at the wheel-rail interface may also lead to changes in the vehicle dynamic behaviour.

Determination of Air Enthalpy Based on Meteorological Data as an Indicator for Heat Stress Assessment in Occupational Outdoor Environments, a Field Study in IRAN.

PubMed

Heidari, Hamidreza; Golbabaei, Farideh; Shamsipour, Aliakbar; Rahimi Forushani, Abbas; Gaeini, Abbasali

2016-01-01

Heat stress evaluation and timely notification, especially using meteorological data is an important issue attracted attention in recent years. Therefore, this study aimed at answering the following research questions: 1) can enthalpy as a common environmental parameter reported by meteorological agencies be applied accurately for evaluation of thermal condition of outdoor settings, and 2) if so, what is it's the best criterion to detect areas in stress or stress-free situations, separately. Nine climatic regions were selected throughout Iran covering a wide variety of climatic conditions like those, which exist around the world. Three types of parameters including measured (ta, RH, Pa and WBGT), estimated (metabolic rate and cloth thermal insulation), and calculated parameters (enthalpy and effective WBGT) were recorded for 1452 different situations. Enthalpy as a new indicator in this research was compared to WBGT in selected regions. Altogether, a good consistency was obtained between enthalpy and WBGT in selected regions (Kappa value: 0.815). Based on the good ROC curve obtained using MedCal software, the criterion of the values more than 74.24 for the new index was determined to explain heat stress situation for outdoor environments. Because of simplicity in measurement, applicability of the indicator for weather agencies, the consistency observed between enthalpy and a valid as well as accurate index (WBGT), sensor requirements which take only a few seconds to reach equilibrium and so on, enthalpy indicator can be introduced and applied as a good substitute for WBGT for outdoor settings.

Molecular energetics of cytosine revisited: a joint computational and experimental study.

PubMed

Gomes, José R B; Ribeiro da Silva, Maria D M C; Freitas, Vera L S; Ribeiro da Silva, Manuel A V

2007-08-02

A static bomb calorimeter has been used to measure the standard molar energy of combustion, in oxygen, at T = 298.15 K, of a commercial sample of cytosine. From this energy, the standard (p degrees = 0.1 MPa) molar enthalpy of formation in the crystalline state was derived as -(221.9 +/- 1.7) kJ.mol(-1). This value confirms one experimental value already published in the literature but differs from another literature value by 13.5 kJ.mol(-1). Using the present standard molar enthalpy of formation in the condensed phase and the enthalpy of sublimation due to Burkinshaw and Mortimer [J. Chem. Soc., Dalton Trans. 1984, 75], (155.0 +/- 3.0) kJ.mol(-1), results in a value for the gas-phase standard molar enthalpy of formation for cytosine of -66.9 kJ.mol(-1). A similar value, -65.1 kJ.mol(-1), has been estimated after G3MP2B3 calculations combined with the reaction of atomization on three different tautomers of cytosine. In agreement with experimental evidence, the hydroxy-amino tautomer is the most stable form of cytosine in the gas phase. The enthalpies of formation of the other two tautomers were also estimated as -60.7 kJ.mol(-1) and -57.2 kJ.mol(-1) for the oxo-amino and oxo-imino tautomers, respectively. The same composite approach was also used to compute other thermochemical data, which is difficult to be measured experimentally, such as C-H, N-H, and O-H bond dissociation enthalpies, gas-phase acidities, and ionization enthalpies.

Customer loads of two-wheeled vehicles

NASA Astrophysics Data System (ADS)

Gorges, C.; Öztürk, K.; Liebich, R.

2017-12-01

Customer usage profiles are the most unknown influences in vehicle design targets and they play an important role in durability analysis. This publication presents a customer load acquisition system for two-wheeled vehicles that utilises the vehicle's onboard signals. A road slope estimator was developed to reveal the unknown slope resistance force with the help of a linear Kalman filter. Furthermore, an automated mass estimator was developed to consider the correct vehicle loading. The mass estimation is performed by an extended Kalman filter. Finally, a model-based wheel force calculation was derived, which is based on the superposition of forces calculated from measured onboard signals. The calculated wheel forces were validated by measurements with wheel-load transducers through the comparison of rainflow matrices. The calculated wheel forces correspond with the measured wheel forces in terms of both quality and quantity. The proposed methods can be used to gather field data for improved vehicle design loads.

Reaction wheels for kinetic energy storage

NASA Astrophysics Data System (ADS)

Studer, P. A.

1984-11-01

In contrast to all existing reaction wheel implementations, an order of magnitude increase in speed can be obtained efficiently if power to the actuators can be recovered. This allows a combined attitude control-energy storage system to be developed with structure mounted reaction wheels. The feasibility of combining reaction wheels with energy storage wwheels is demonstrated. The power required for control torques is a function of wheel speed but this energy is not dissipated; it is stored in the wheel. The I(2)R loss resulting from a given torque is shown to be constant, independent of the design speed of the motor. What remains, in order to efficiently use high speed wheels (essential for energy storage) for control purposes, is to reduce rotational losses to acceptable levels. Progress was made in permanent magnet motor design for high speed operation. Variable field motors offer more control flexibility and efficiency over a broader speed range.

Highly accurate articulated coordinate measuring machine

DOEpatents

Bieg, Lothar F.; Jokiel, Jr., Bernhard; Ensz, Mark T.; Watson, Robert D.

2003-12-30

Disclosed is a highly accurate articulated coordinate measuring machine, comprising a revolute joint, comprising a circular encoder wheel, having an axis of rotation; a plurality of marks disposed around at least a portion of the circumference of the encoder wheel; bearing means for supporting the encoder wheel, while permitting free rotation of the encoder wheel about the wheel's axis of rotation; and a sensor, rigidly attached to the bearing means, for detecting the motion of at least some of the marks as the encoder wheel rotates; a probe arm, having a proximal end rigidly attached to the encoder wheel, and having a distal end with a probe tip attached thereto; and coordinate processing means, operatively connected to the sensor, for converting the output of the sensor into a set of cylindrical coordinates representing the position of the probe tip relative to a reference cylindrical coordinate system.

Reaction wheels for kinetic energy storage

NASA Technical Reports Server (NTRS)

Studer, P. A.

1984-01-01

In contrast to all existing reaction wheel implementations, an order of magnitude increase in speed can be obtained efficiently if power to the actuators can be recovered. This allows a combined attitude control-energy storage system to be developed with structure mounted reaction wheels. The feasibility of combining reaction wheels with energy storage wwheels is demonstrated. The power required for control torques is a function of wheel speed but this energy is not dissipated; it is stored in the wheel. The I(2)R loss resulting from a given torque is shown to be constant, independent of the design speed of the motor. What remains, in order to efficiently use high speed wheels (essential for energy storage) for control purposes, is to reduce rotational losses to acceptable levels. Progress was made in permanent magnet motor design for high speed operation. Variable field motors offer more control flexibility and efficiency over a broader speed range.

Thermal modal analysis of novel non-pneumatic mechanical elastic wheel based on FEM and EMA

NASA Astrophysics Data System (ADS)

Zhao, Youqun; Zhu, Mingmin; Lin, Fen; Xiao, Zhen; Li, Haiqing; Deng, Yaoji

2018-01-01

A combination of Finite Element Method (FEM) and Experiment Modal Analysis (EMA) have been employed here to characterize the structural dynamic response of mechanical elastic wheel (ME-Wheel) operating under a specific thermal environment. The influence of high thermal condition on the structural dynamic response of ME-Wheel is investigated. The obtained results indicate that the EMA results are in accordance with those obtained using the proposed Finite Element (FE) model, indicting the high reliability of this FE model applied in analyzing the modal of ME-Wheel working under practical thermal environment. It demonstrates that the structural dynamic response of ME-Wheel operating under a specific thermal condition can be predicted and evaluated using the proposed analysis method, which is beneficial for the dynamic optimization design of the wheel structure to avoid tire temperature related vibration failure and improve safety of tire.

The colour wheels of art, perception, science and physiology

NASA Astrophysics Data System (ADS)

Harkness, Nick

2006-06-01

Colour is not the domain of any one discipline be it art, philosophy, psychology or science. Each discipline has its own colour wheel and this presentation examines the origins and philosophies behind the colour circles of Art, Perception, Science and Physiology (after image) with reference to Aristotle, Robert Boyle, Leonardo da Vinci, Goethe, Ewald Hering and Albert Munsell. The paper analyses and discusses the differences between the four colour wheels using the Natural Colour System® notation as the reference for hue (the position of colours within each of the colour wheels). Examination of the colour wheels shows the dominance of blue in the wheels of art, science and physiology particularly at the expense of green. This paper does not consider the three-dimensionality of colour space its goal was to review the hue of a colour with regard to its position on the respective colour wheels.

Green's functions for analysis of dynamic response of wheel/rail to vertical excitation

NASA Astrophysics Data System (ADS)

Mazilu, Traian

2007-09-01

An analytical model to simulate wheel/rail interaction using the Green's functions method is proposed in this paper. The model consists of a moving wheel on a discretely supported rail. Particularly for this model of rail, the bending and the longitudinal displacement are coupled due to the rail pad and a complex model of the rail pad is adopted. An efficient method for solving a time-domain analysis for wheel/rail interaction is presented. The method is based on the properties of the rail's Green functions and starting to these functions, a track's Green matrix is assembled for the numerical simulations of wheel/rail response due to three kinds of vertical excitations: the steady-state interaction, the rail corrugation and the wheel flat. The study points to influence of the worn rail—rigid contact—on variation in the wheel/rail contact force. The concept of pinned-pinned inhibitive rail pad is also presented.

77 FR 75697 - Petition for Waiver of Compliance

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-21

... wheel loads when a rail vehicle traverses a curve. With the right combination of speed, curvature, and... wheels will be equal, i.e., balanced. The curving speed corresponding to this balanced state is referred... the outer wheel load to increase and the inner wheel load to decrease. The manifestation of this load...

16 CFR 1420.3 - Requirements for four-wheel ATVs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Requirements for four-wheel ATVs. 1420.3... REGULATIONS REQUIREMENTS FOR ALL TERRAIN VEHICLES § 1420.3 Requirements for four-wheel ATVs. (a) Each ATV shall comply with all applicable provisions of the American National Standard for Four Wheel All-Terrain...

29 CFR 1915.134 - Abrasive wheels.

Code of Federal Regulations, 2012 CFR

2012-07-01

... shall be so mounted as to maintain proper alignment with the wheel, and the guard and its fastenings... safety flanges are required, they shall be used only with wheels designed to fit the flanges. Only safety... wheels shall fit freely on the spindle and shall not be forced on. The spindle nut shall be tightened...

29 CFR 1915.134 - Abrasive wheels.

Code of Federal Regulations, 2013 CFR

2013-07-01

... shall be so mounted as to maintain proper alignment with the wheel, and the guard and its fastenings... safety flanges are required, they shall be used only with wheels designed to fit the flanges. Only safety... wheels shall fit freely on the spindle and shall not be forced on. The spindle nut shall be tightened...

29 CFR 1915.134 - Abrasive wheels.

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall be so mounted as to maintain proper alignment with the wheel, and the guard and its fastenings... safety flanges are required, they shall be used only with wheels designed to fit the flanges. Only safety... wheels shall fit freely on the spindle and shall not be forced on. The spindle nut shall be tightened...

75 FR 56991 - Grant of Authority for Subzone Status Michelin North America, Inc. (Tire Distribution and Wheel...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-17

... Status Michelin North America, Inc. (Tire Distribution and Wheel Assembly) Baltimore, MD Pursuant to its... warehouse/distribution and wheel assembly facility of Michelin North America, Inc., located in Elkton, MD... tire accessories warehousing and distribution and wheel assembly at the facility of Michelin North...

Planter closing wheel effects on cotton emergence in a conservation tillage system

USDA-ARS?s Scientific Manuscript database

Closing wheels on a row crop planter help provide good seed-soil contact during planting and can influence emergence and crop stand. Various types of closing wheels are available to producers for use on planters. Seven closing wheel types were used on a row crop planter planting cotton in a conser...

Geneva mechanism. [including star wheel and driver

NASA Technical Reports Server (NTRS)

Summers, R. H.; Kenney, R. L. (Inventor)

1974-01-01

An improved Geneva mechanism is characterized by a driven star-wheel having a segmented cam-follower surface. Star-wheel driver includes a restraining cam having a segmented cam surface for engaging the cam-follower surface of the star-wheel and antifriction rollers pinned to the restraining cam for engaging the cam-follower surface.

77 FR 76027 - PowerWheel Associates; Notice of Termination of Exemption by Implied Surrender and Soliciting...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-26

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 12119-000] PowerWheel... Initiated: November 20, 2012. d. Exemptee: PowerWheel Associates. e. Name and Location of Project: The... Contact Information: Mr. Kenneth R. Broome, PowerWheel Associates, 100 Rocky Creek Road, Woodside, CA...

16 CFR 1512.12 - Requirements for wheel hubs.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Requirements for wheel hubs. 1512.12 Section... REGULATIONS REQUIREMENTS FOR BICYCLES Regulations § 1512.12 Requirements for wheel hubs. All bicycles (other... hub retention test, § 1512.18(j)(3), to assure that when the locking devices are released the wheel...

16 CFR 1512.12 - Requirements for wheel hubs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Requirements for wheel hubs. 1512.12 Section... REGULATIONS REQUIREMENTS FOR BICYCLES Regulations § 1512.12 Requirements for wheel hubs. All bicycles (other... hub retention test, § 1512.18(j)(3), to assure that when the locking devices are released the wheel...

29 CFR 1917.44 - General rules applicable to vehicles. 4

Code of Federal Regulations, 2012 CFR

2012-07-01

... shall first be deflated by valve core removal; and (ix) Before assembly, wheel components shall be... outside the frame of the device for any wheel position within the device. When the wheel assembly is... trailer road wheels prior to disconnection of the trailer and until braking is again provided. Section 49...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

29 CFR 1917.44 - General rules applicable to vehicles. 4

Code of Federal Regulations, 2013 CFR

2013-07-01

... shall first be deflated by valve core removal; and (ix) Before assembly, wheel components shall be... outside the frame of the device for any wheel position within the device. When the wheel assembly is... trailer road wheels prior to disconnection of the trailer and until braking is again provided. Section 49...

29 CFR 1917.44 - General rules applicable to vehicles. 4

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall first be deflated by valve core removal; and (ix) Before assembly, wheel components shall be... outside the frame of the device for any wheel position within the device. When the wheel assembly is... trailer road wheels prior to disconnection of the trailer and until braking is again provided. Section 49...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

49 CFR 570.59 - Service brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the following tests. (1) Roller-type or drive-on platform tests. The force applied by the brake on a front wheel or a rear wheel shall not differ by more than 25 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i) Inspection procedure. The vehicle...

Wheel running in the wild.

PubMed

Meijer, Johanna H; Robbers, Yuri

2014-07-07

The importance of exercise for health and neurogenesis is becoming increasingly clear. Wheel running is often used in the laboratory for triggering enhanced activity levels, despite the common objection that this behaviour is an artefact of captivity and merely signifies neurosis or stereotypy. If wheel running is indeed caused by captive housing, wild mice are not expected to use a running wheel in nature. This however, to our knowledge, has never been tested. Here, we show that when running wheels are placed in nature, they are frequently used by wild mice, also when no extrinsic reward is provided. Bout lengths of running wheel behaviour in the wild match those for captive mice. This finding falsifies one criterion for stereotypic behaviour, and suggests that running wheel activity is an elective behaviour. In a time when lifestyle in general and lack of exercise in particular are a major cause of disease in the modern world, research into physical activity is of utmost importance. Our findings may help alleviate the main concern regarding the use of running wheels in research on exercise.

Fault detection method for railway wheel flat using an adaptive multiscale morphological filter

NASA Astrophysics Data System (ADS)

Li, Yifan; Zuo, Ming J.; Lin, Jianhui; Liu, Jianxin

2017-02-01

This study explores the capacity of the morphology analysis for railway wheel flat fault detection. A dynamic model of vehicle systems with 56 degrees of freedom was set up along with a wheel flat model to calculate the dynamic responses of axle box. The vehicle axle box vibration signal is complicated because it not only contains the information of wheel defect, but also includes track condition information. Thus, how to extract the influential features of wheels from strong background noise effectively is a typical key issue for railway wheel fault detection. In this paper, an algorithm for adaptive multiscale morphological filtering (AMMF) was proposed, and its effect was evaluated by a simulated signal. And then this algorithm was employed to study the axle box vibration caused by wheel flats, as well as the influence of track irregularity and vehicle running speed on diagnosis results. Finally, the effectiveness of the proposed method was verified by bench testing. Research results demonstrate that the AMMF extracts the influential characteristic of axle box vibration signals effectively and can diagnose wheel flat faults in real time.

Determining Wheel-Soil Interaction Loads Using a Meshfree Finite Element Approach Assisting Future Missions with Rover Wheel Design

NASA Technical Reports Server (NTRS)

Contreras, Michael T.; Peng, Chia-Yen; Wang, Dongdong; Chen, Jiun-Shyan

2012-01-01

A wheel experiencing sinkage and slippage events poses a high risk to rover missions as evidenced by recent mobility challenges on the Mars Exploration Rover (MER) project. Because several factors contribute to wheel sinkage and slippage conditions such as soil composition, large deformation soil behavior, wheel geometry, nonlinear contact forces, terrain irregularity, etc., there are significant benefits to modeling these events to a sufficient degree of complexity. For the purposes of modeling wheel sinkage and slippage at an engineering scale, meshfree finite element approaches enable simulations that capture sufficient detail of wheel-soil interaction while remaining computationally feasible. This study demonstrates some of the large deformation modeling capability of meshfree methods and the realistic solutions obtained by accounting for the soil material properties. A benchmark wheel-soil interaction problem is developed and analyzed using a specific class of meshfree methods called Reproducing Kernel Particle Method (RKPM). The benchmark problem is also analyzed using a commercially available finite element approach with Lagrangian meshing for comparison. RKPM results are comparable to classical pressure-sinkage terramechanics relationships proposed by Bekker-Wong. Pending experimental calibration by future work, the meshfree modeling technique will be a viable simulation tool for trade studies assisting rover wheel design.

Adult wheel access interaction with activity and boldness personality in Siberian dwarf hamsters (Phodopus sungorus).

PubMed

Kanda, L Leann; Abdulhay, Amir; Erickson, Caitlin

2017-05-01

Individual animal personalities interact with environmental conditions to generate differences in behavior, a phenomenon of growing interest for understanding the effects of environmental enrichment on captive animals. Wheels are common environmental enrichment for laboratory rodents, but studies conflict on how this influences behavior, and interaction of wheels with individual personalities has rarely been examined. We examined whether wheel access altered personality profiles in adult Siberian dwarf hamsters. We assayed animals in a tunnel maze twice for baseline personality, then again at two and at seven weeks after the experimental group was provisioned with wheels in their home cages. Linear mixed model selection was used to assess changes in behavior over time and across environmental gradient of wheel exposure. While animals showed consistent inter-individual differences in activity, activity personality did not change upon exposure to a wheel. Boldness also varies among individuals, and there is evidence for female boldness scores converging after wheel exposure, that is, opposite shifts in behavior by high and low boldness individuals, although sample size is too small for the mixed model results to be robust. In general, Siberian dwarf hamsters appear to show low behavioral plasticity, particularly in general activity, in response to running wheels. Copyright © 2017 Elsevier B.V. All rights reserved.

Taste avoidance induced by wheel running: effects of backward pairings and robustness of conditioned taste aversion.

PubMed

Salvy, Sarah-Jeanne; Pierce, W David; Heth, Donald C; Russell, James C

2004-09-15

Rats repeatedly exposed to a distinctive novel solution (conditioned stimulus, CS) followed by the opportunity to run in a wheel subsequently drink less of this solution. Investigations on this phenomenon indicate that wheel running is an effective unconditioned stimulus (US) for establishing conditioned taste aversion (CTA) when using a forward conditioning procedure (i.e., the US-wheel running follows the CS-taste). However, other studies show that wheel running produces reliable preference for a distinctive place when pairings are backward (i.e., the CS-location follows the US-wheel running). One possibility to account for these results is that rewarding aftereffects of wheel running conditioned preference to the CS. The main objective of the present study was to assess the effects of backward conditioning using wheel running as the US and a distinctive taste as the CS. In a between-groups design, two experimental groups [i.e., forward (FC) and backward conditioning (BC)] and two control groups [CS-taste alone (TA) and CS-US unpaired (UNP)] were compared. Results from this experiment indicated that there is less suppression of drinking when a CS-taste followed a bout of wheel running. In fact, rats in the BC group drank more of the paired solution than all the other groups.

Multi-disciplinary optimization of railway wheels

NASA Astrophysics Data System (ADS)

Nielsen, J. C. O.; Fredö, C. R.

2006-06-01

A numerical procedure for multi-disciplinary optimization of railway wheels, based on Design of Experiments (DOE) methodology and automated design, is presented. The target is a wheel design that meets the requirements for fatigue strength, while minimizing the unsprung mass and rolling noise. A 3-level full factorial (3LFF) DOE is used to collect data points required to set up Response Surface Models (RSM) relating design and response variables in the design space. Computationally efficient simulations are thereafter performed using the RSM to identify the solution that best fits the design target. A demonstration example, including four geometric design variables in a parametric finite element (FE) model, is presented. The design variables are wheel radius, web thickness, lateral offset between rim and hub, and radii at the transitions rim/web and hub/web, but more variables (including material properties) can be added if needed. To improve further the performance of the wheel design, a constrained layer damping (CLD) treatment is applied on the web. For a given load case, compared to a reference wheel design without CLD, a combination of wheel shape and damping optimization leads to the conclusion that a reduction in the wheel component of A-weighted rolling noise of 11 dB can be achieved if a simultaneous increase in wheel mass of 14 kg is accepted.

Further study on the wheel-rail impact response induced by a single wheel flat: the coupling effect of strain rate and thermal stress

NASA Astrophysics Data System (ADS)

Jing, Lin; Han, Liangliang

2017-12-01

A comprehensive dynamic finite-element simulation method was proposed to study the wheel-rail impact response induced by a single wheel flat based on a 3-D rolling contact model, where the influences of the structural inertia, strain rate effect of wheel-rail materials and thermal stress due to the wheel-rail sliding friction were considered. Four different initial conditions (i.e. pure mechanical loading plus rate-independent, pure mechanical loading plus rate-dependent, thermo-mechanical loading plus rate-independent, and thermo-mechanical loading plus rate-dependent) were involved into explore the corresponding impact responses in term of the vertical impact force, von-Mises equivalent stress, equivalent plastic strain and shear stress. Influences of train speed, flat length and axle load on the flat-induced wheel-rail impact response were discussed, respectively. The results indicate that the maximum thermal stresses are occurred on the tread of the wheel and on the top surface of the middle rail; the strain rate hardening effect contributes to elevate the von-Mises equivalent stress and restrain the plastic deformation; and the initial thermal stress due to the sliding friction will aggravate the plastic deformation of wheel and rail. Besides, the wheel-rail impact responses (i.e. impact force, von-Mises equivalent stress, equivalent plastic strain, and XY shear stress) induced by a flat are sensitive to the train speed, flat length and axle load.

Position and force control of a vehicle with two or more steerable drive wheels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reister, D.B.; Unseren, M.A.

1992-10-01

When a vehicle with two or more steerable drive wheels is traveling in a circle, the motion of the wheels is constrained. The wheel translational velocity divided by the radius to the center of rotation must be the same for all wheels. When the drive wheels are controlled independently using position control, the motion of the wheels may violate the constraints and the wheels may slip. Consequently, substantial errors can occur in the orientation of the vehicle. A vehicle with N drive wheels has (N - 1) constraints and one degree of freedom. We have developed a new approach tomore » the control of a vehicle with N steerable drive wheels. The novel aspect of our approach is the use of force control. To control the vehicle, we have one degree of freedom for the position on the circle and (N - 1) forces that can be used to reduce errors. Recently, Kankaanranta and Koivo developed a control architecture that allows the force and position degrees of freedom to be decoupled. In the work of Kankaanranta and Koivo the force is an exogenous input. We have made the force endogenous by defining the force in terms of the errors in satisfying the rigid body kinematic constraints. We have applied the control architecture to the HERMIES-III robot and have measured a dramatic reduction in error (more than a factor of 20) compared to motions without force control.« less

Modelling, validation and analysis of a three-dimensional railway vehicle-track system model with linear and nonlinear track properties in the presence of wheel flats

NASA Astrophysics Data System (ADS)

Uzzal, R. U. A.; Ahmed, A. K. W.; Bhat, R. B.

2013-11-01

This paper presents dynamic contact loads at wheel-rail contact point in a three-dimensional railway vehicle-track model as well as dynamic response at vehicle-track component levels in the presence of wheel flats. The 17-degrees of freedom lumped mass vehicle is modelled as a full car body, two bogies and four wheelsets, whereas the railway track is modelled as two parallel Timoshenko beams periodically supported by lumped masses representing the sleepers. The rail beam is also supported by nonlinear spring and damper elements representing the railpad and ballast. In order to ensure the interactions between the railpads, a shear parameter beneath the rail beams has also been considered into the model. The wheel-rail contact is modelled using nonlinear Hertzian contact theory. In order to solve the coupled partial and ordinary differential equations of the vehicle-track system, modal analysis method is employed. Idealised Haversine wheel flats with the rounded corner are included in the wheel-rail contact model. The developed model is validated with the existing measured and analytical data available in the literature. The nonlinear model is then employed to investigate the wheel-rail impact forces that arise in the wheel-rail interface due to the presence of wheel flats. The validated model is further employed to investigate the dynamic responses of vehicle and track components in terms of displacement, velocity, and acceleration in the presence of single wheel flat.

Influence of wheel size on muscle activity and tri-axial accelerations during cross-country mountain biking.

PubMed

Hurst, Howard Thomas; Sinclair, Jonathan; Atkins, Stephen; Rylands, Lee; Metcalfe, John

2017-07-01

This study aimed to investigate the influence of different mountain bike wheel diameters on muscle activity and whether larger diameter wheels attenuate muscle vibrations during cross-country riding. Nine male competitive mountain bikers (age 34.7 ± 10.7 years; stature 177.7 ± 5.6 cm; body mass 73.2 ± 8.6 kg) participated in the study. Riders performed one lap at race pace on 26, 27.5 and 29 inch wheeled mountain bikes. sEMG and acceleration (RMS) were recorded for the full lap and during ascent and descent phases at the gastrocnemius, vastus lateralis, biceps brachii and triceps brachii. No significant main effects were found by wheel size for each of the four muscle groups for sEMG or acceleration during the full lap and for ascent and descent (P > .05). When data were analysed between muscle groups, significant differences were found between biceps brachii and triceps brachii (P < .05) for all wheel sizes and all phases of the lap with the exception of for the 26 inch wheel during the descent. Findings suggest wheel diameter has no influence on muscle activity and vibration during mountain biking. However, more activity was observed in the biceps brachii during 26 inch wheel descending. This is possibly due to an increased need to manoeuvre the front wheel over obstacles.

The protective effects of free wheel-running against cocaine psychomotor sensitization persist after exercise cessation in C57BL/6J mice.

PubMed

Lespine, L-F; Tirelli, E

2015-12-03

Previous literature suggests that free access to a running wheel can attenuate the behavioral responsiveness to addictive drugs in rodents. In a few studies, wheel-running cessation accentuated drug responsiveness. Here, we tested whether free wheel-running cessation is followed by (1) an accentuation or (2) an attenuation of cocaine psychomotor sensitization, knowing that no cessation of (continuous) wheel-running is associated with an attenuation of cocaine responsiveness. Male C57BL/6J mice, aged 35 days, were housed singly either with (exercising mice) or without (non-exercising mice) a running wheel. At the end of a period of 36 days, half of the exercising mice were deprived of their wheel whereas the other half of exercising mice kept their wheel until the end of experimentation (which lasted 85 days). The non-exercising mice were housed without wheel throughout experimentation. Testing took place 3 days after exercise cessation. After 2 once-daily drug-free test sessions, mice were tested for initiation of psychomotor sensitization over 13 once-daily injections of 8 mg/kg cocaine. Post-sensitization conditioned activation (saline challenge) and long-term expression of sensitization were assessed 2 or 30 days after the last sensitizing injection (same treatments as for initiation of sensitization), respectively. Exercising mice and mice undergoing wheel-running cessation exhibited comparable degrees of attenuation of all cocaine effects in comparison with the continuously non-exercising mice, which showed the greatest effects. Thus, the efficaciousness of wheel-running at attenuating cocaine sensitization not only resisted to exercise cessation but was also unambiguously persistent (an important effect rarely reported in previous literature). Copyright © 2015 IBRO. Published by Elsevier Ltd. All rights reserved.

Wind-Powered Wheel Locomotion, Initiated by Leaping Somersaults, in Larvae of the Southeastern Beach Tiger Beetle (Cicindela dorsalis media)

PubMed Central

Harvey, Alan; Zukoff, Sarah

2011-01-01

Rapid movement is challenging for elongate, soft-bodied animals with short or no legs. Leaping is known for only a few animals with this “worm-like” morphology. Wheel locomotion, in which the animal's entire body rolls forward along a central axis, has been reported for only a handful of animals worldwide. Here we present the first documented case of wind-powered wheel locomotion, in larvae of the coastal tiger beetle Cicindela dorsalis media. When removed from their shallow burrows, larvae easily can be induced to enter a behavioral sequence that starts with leaping; while airborne, larvae loop their body into a rotating wheel and usually either “hit the ground rolling” or leap again. The direction larvae wheel is closely related to the direction in which winds are blowing; thus, all our larvae wheeled up-slope, as winds at our study site consistently blew from sea to land. Stronger winds increased both the proportion of larvae wheeling, and the distance traveled, exceeding 60 m in some cases. In addition, the proportion of larvae that wheel and the distance traveled by wheeling larvae are significantly greater on smooth sandy beaches than on beach surfaces made rough and irregular by pedestrian, equestrian, and vehicular traffic. Like other coastal species of tiger beetles, C. dorsalis media has suffered major declines in recent years that are clearly correlated with increased human impacts. The present study suggests that the negative effects of beach traffic may be indirect, preventing larvae from escaping from predators using wheel locomotion by disrupting the flat, hard surface necessary for efficient wheeling. PMID:21448275

Sex differences in the effect of wheel running on subsequent nicotine-seeking in a rat adolescent-onset self-administration model.

PubMed

Sanchez, Victoria; Moore, Catherine F; Brunzell, Darlene H; Lynch, Wendy J

2014-04-01

Wheel running attenuates nicotine-seeking in male adolescent rats; however, it is not known if this effect extends to females. To determine if wheel running during abstinence would differentially attenuate subsequent nicotine-seeking in male and female rats that had extended access to nicotine self-administration during adolescence. Male (n = 49) and female (n = 43) adolescent rats self-administered saline or nicotine (5 μg/kg) under an extended access (23-h) paradigm. Following the last self-administration session, rats were moved to polycarbonate cages for an abstinence period where they either had access to a locked or unlocked running wheel for 2 h/day. Subsequently, nicotine-seeking was examined under a within-session extinction/cue-induced reinstatement paradigm. Due to low levels of nicotine-seeking in females in both wheel groups, additional groups were included that were housed without access to a running wheel during abstinence. Females self-administered more nicotine as compared to males; however, within males and females, intake did not differ between groups prior to wheel assignment. Compared to saline controls, males and females that self-administered nicotine showed a significant increase in drug-seeking during extinction. Wheel running during abstinence attenuated nicotine-seeking during extinction in males. In females, access to either locked or unlocked wheels attenuated nicotine-seeking during extinction. While responding was reinstated by cues in both males and females, levels were modest and not significantly affected by exercise in this adolescent-onset model. While wheel running reduced subsequent nicotine-seeking in males, access to a wheel, either locked or unlocked, was sufficient to suppress nicotine-seeking in females.

Wheel-running mitigates psychomotor sensitization initiation but not post-sensitization conditioned activity and conditioned place preference induced by cocaine in mice.

PubMed

Geuzaine, Annabelle; Tirelli, Ezio

2014-04-01

Previous literature suggests that physical exercise allowed by an unlimited access to a running wheel for several weeks can mitigate chronic neurobehavioral responsiveness to several addictive drugs in rodents. Here, the potential preventive effects of unlimited wheel-running on the initiation of psychomotor sensitization and the acquisition and extinction of conditioned place preference (CPP) induced by 10 mg/kg cocaine in C56BL/6J mice were assessed in two independent experiments. To this end, half of the mice were singly housed with a running wheel at 28 days of age for 10 weeks prior to psychopharmacological tests, during which housing conditions did not change, and the other half of mice were housed without running wheel. In Experiment 1, prior to initiating sensitization, psychomotor activity on the two first drug-free once-daily sessions was not affected by wheel-running. This was also found for the acute psychomotor-activating effect of cocaine on the first sensitization session. Psychomotor sensitization readily developed over the 9 following once-daily sessions in mice housed without wheel, whereas it was inhibited in mice housed with a wheel. However, that difference did not transfer to post-sensitization conditioned activity. In contrast with the sensitization results, mice housed with a wheel still expressed a clear-cut CPP which did not extinguish differently from that of the other group, a result in disaccord with previous studies reporting either an attenuating or an increasing effect of wheel-running on cocaine-induced conditioned reward. The available results together indicate that interactions between wheel-running and cocaine effects are far from being satisfactorily characterized. Copyright © 2014 Elsevier B.V. All rights reserved.

Sex differences in the effect of wheel running on subsequent nicotine-seeking in a rat adolescent-onset self-administration model

PubMed Central

Sanchez, Victoria; Moore, Catherine F; Brunzell, Darlene H; Lynch, Wendy J

2014-01-01

Rationale Wheel running attenuates nicotine-seeking in male adolescent rats; however it is not known if this effect extends to females. Objective To determine if wheel running during abstinence would differentially attenuate subsequent nicotine-seeking in male and female rats that had extended access to nicotine self-administration during adolescence. Methods Male (N = 49) and female (N = 43) adolescent rats self-administered saline or nicotine (5μg/kg) under an extended access (23-hour) paradigm. Following the last self-administration session, rats were moved to polycarbonate cages for an abstinence period where they either had access to a locked or unlocked running wheel for 2-hours/day. Subsequently, nicotine-seeking was examined under a within-session extinction/cue-induced reinstatement paradigm. Due to low levels of nicotine-seeking in females in both wheel groups, additional groups were included that were housed without access to a running wheel during abstinence. Results Females self-administered more nicotine as compared to males; however, within males and females, intake did not differ between groups prior to wheel assignment. Compared to saline controls, males and females that self-administered nicotine showed a significant increase in drug-seeking during extinction. Wheel running during abstinence attenuated nicotine-seeking during extinction in males. In females, access to either locked or unlocked wheels attenuated nicotine-seeking during extinction. While responding was reinstated by cues in both males and females, levels were modest and not significantly affected by exercise in this adolescent-onset model. Conclusions While wheel running reduced subsequent nicotine-seeking in males, access to a wheel, either locked or unlocked, was sufficient to suppress nicotine-seeking in females. PMID:24271035

Effect of sucrose availability on wheel-running as an operant and as a reinforcing consequence on a multiple schedule: Additive effects of extrinsic and automatic reinforcement.

PubMed

Belke, Terry W; Pierce, W David

2015-07-01

As a follow up to Belke and Pierce's (2014) study, we assessed the effects of repeated presentation and removal of sucrose solution on the behavior of rats responding on a two-component multiple schedule. Rats completed 15 wheel turns (FR 15) for either 15% or 0% sucrose solution in the manipulated component and lever pressed 10 times on average (VR 10) for an opportunity to complete 15 wheel turns (FR 15) in the other component. In contrast to our earlier study, the components advanced based on time (every 8min) rather than completed responses. Results showed that in the manipulated component wheel-running rates were higher and the latency to initiate running longer when sucrose was present (15%) compared to absent (0% or water); the number of obtained outcomes (sucrose/water), however, did not differ with the presentation and withdrawal of sucrose. For the wheel-running as reinforcement component, rates of wheel turns, overall lever-pressing rates, and obtained wheel-running reinforcements were higher, and postreinforcement pauses shorter, when sucrose was present (15%) than absent (0%) in manipulated component. Overall, our findings suggest that wheel-running rate regardless of its function (operant or reinforcement) is maintained by automatically generated consequences (automatic reinforcement) and is increased as an operant by adding experimentally arranged sucrose reinforcement (extrinsic reinforcement). This additive effect on operant wheel-running generalizes through induction or arousal to the wheel-running as reinforcement component, increasing the rate of responding for opportunities to run and the rate of wheel-running per opportunity. Copyright © 2015 Elsevier B.V. All rights reserved.

The Effect of Assistive Anchor-Like Grousers on Wheeled Rover Performance over Unconsolidated Sandy Dune Inclines

PubMed Central

Ibrahim, Ahmad Najmuddin; Aoshima, Shinichi; Shiroma, Naoji; Fukuoka, Yasuhiro

2016-01-01

Typical rovers with wheels equipped with conventional grousers are prone to getting stuck in unconsolidated sandy dune inclines as the wheels tend to sink into the sand. This phenomenon is caused by the motion of the grouser through the sand during the latter half of the rotation, in which the grouser pushes the sand from underneath the wheel upwards and towards the backside of the wheel. This creates a space that the wheel can sink into. To minimize sand movement and subsequent sinkage, we propose the concept of using an “assistive grouser”, which is attached to the side of a conventional rover wheel. The assistive grouser is designed to be able to autonomously maintain a uniform angle relative to the rover body independent of the rotation of the wheels. Rotating the wheel causes the assistive grousers to automatically penetrate into the sand slope surface at a constant angle of attack, thereby acting as an anchor and providing traction for the wheel. Maintaining a uniform grouser angle as opposed to a rotating motion also assists in extracting the grouser out of the sand without moving the sand towards the back of the wheel. Moreover, the angle of the assistive grousers is held constantly by a single dedicated motor, meaning that the angle of the assistive grousers can be optimized to provide the least amount of sinkage for each slope angle. The experimental results showed that for slope angles of 0–30 degrees, the rover equipped with the proposed assistive grousers experienced significantly less sinkage and consumed less current compared to the rover equipped with conventional grousers. PMID:27649196

An investigation into the mechanism of the polygonal wear of metro train wheels and its effect on the dynamic behaviour of a wheel/rail system

NASA Astrophysics Data System (ADS)

Jin, Xuesong; Wu, Lei; Fang, Jianying; Zhong, Shuoqiao; Ling, Liang

2012-12-01

This paper presents a detailed investigation conducted into the mechanism of the polygonal wear of metro train wheels through extensive experiments conducted at the sites. The purpose of the experimental investigation is to determine from where the resonant frequency that causes the polygonal wear of the metro train wheels originates. The experiments include the model tests of a vehicle and its parts and the tracks, the dynamic behaviour test of the vehicle in operation and the observation test of the polygonal wear development of the wheels. The tracks tested include the viaducts and the tunnel tracks. The structure model tests show that the average passing frequency of a polygonal wheel is approximately close to the first bending resonant frequency of the wheelset that is found by the wheelset model test and verified by the finite element analysis of the wheelset. Also, the dynamic behaviour test of the vehicle in operation indicates the main frequencies of the vertical acceleration vibration of the axle boxes, which are dominant in the vertical acceleration vibration of the axle boxes and close to the passing frequency of a polygonal wheel, which shows that the first bending resonant frequency of the wheelset is very exciting in the wheelset operation. The observation test of the polygonal wear development of the wheels indicates an increase in the rate of the polygonal wear of the wheels after their re-profiling. This paper also describes the dynamic models used for the metro vehicle coupled with the ballasted track and the slab track to analyse the effect of the polygonal wear of the wheels on the wheel/rail normal forces.

Effects of voluntary exercise on spontaneous physical activity and food consumption in mice: Results from an artificial selection experiment.

PubMed

Copes, Lynn E; Schutz, Heidi; Dlugosz, Elizabeth M; Acosta, Wendy; Chappell, Mark A; Garland, Theodore

2015-10-01

We evaluated the effect of voluntary exercise on spontaneous physical activity (SPA) and food consumption in mice from 4 replicate lines bred for 57 generations for high voluntary wheel running (HR) and from 4 non-selected control (C) lines. Beginning at ~24 days of age, mice were housed in standard cages or in cages with attached wheels. Wheel activity and SPA were monitored in 1-min intervals. Data from the 8th week of the experiment were analyzed because mice were sexually mature and had plateaued in body mass, weekly wheel running distance, SPA, and food consumption. Body mass, length, and masses of the retroperitoneal fat pad, liver, and heart were recorded after the 13th week. SPA of both HR and C mice decreased with wheel access, due to reductions in both duration and average intensity of SPA. However, total activity duration (SPA+wheel running; min/day) was ~1/3 greater when mice were housed with wheels, and food consumption was significantly increased. Overall, food consumption in both HR and C mice was more strongly affected by wheel running than by SPA. Duration of wheel running had a stronger effect than average speed, but the opposite was true for SPA. With body mass as a covariate, chronic wheel access significantly reduced fat pad mass and increased heart mass in both HR and C mice. Given that both HR and C mice housed with wheels had increased food consumption, the energetic cost of wheel running was not fully compensated by concomitant reductions in SPA. The experiment demonstrates that both duration and intensity of both wheel running and SPA were significant predictors of food consumption. This sort of detailed analysis of the effects of different aspects of physical activity on food consumption has not previously been reported for a non-human animal, and it sets the stage for longitudinal examination of energy balance and its components in rodent models. Copyright © 2015 Elsevier Inc. All rights reserved.

Circadian rhythm disruption by a novel running wheel: Roles of exercise and arousal in blockade of the luteinizing hormone surge

PubMed Central

Duncan, Marilyn J.; Franklin, Kathleen M.; Peng, Xiaoli; Yun, Christopher; Legan, Sandra J.

2014-01-01

Exposure of proestrous Syrian hamsters to a new room, cage, and novel running wheel blocks the luteinizing hormone (LH) surge until the next day in ~75% of hamsters (Legan et al, 2010) [1]. The studies described here tested the hypotheses that 1) exercise and/or 2) orexinergic neurotransmission mediate novel wheel blockade of the LH surge and circadian phase advances. Female hamsters were exposed to a 14L:10D photoperiod and activity rhythms were monitored with infra-red detectors. In Expt. 1, to test the effect of exercise, hamsters received jugular cannulae and on the next day, proestrus (Day 1), shortly before zeitgeber time 5 (ZT 5, 7 hours before lights-off) the hamsters were transported to the laboratory. After obtaining a blood sample at ZT 5, the hamsters were transferred to a new cage with a novel wheel that was either freely rotating (unlocked), or locked until ZT 9, and exposed to constant darkness (DD). Blood samples were collected hourly for 2 days from ZT 5–11 under red light for determination of plasma LH levels by radioimmunoassay. Running rhythms were monitored continuously for the next 10–14 days. The locked wheels were as effective as unlocked wheels in blocking LH surges (no Day 1 LH surge in 6/9 versus 8/8 hamsters, P>0.05) and phase advances in the activity rhythms did not differ between the groups (P= 0.28), suggesting that intense exercise is not essential for novel wheel blockade and phase advance of the proestrous LH surge. Expt. 2 tested whether orexin neurotransmission is essential for these effects. Hamsters were treated the same as in Expt. 1 except they were injected (i.p.) at ZT 4.5 and 5 with either the orexin 1 receptor antagonist SB334867 (15 mg/kg per injection) or vehicle (25% DMSO in 2-hydroxypropyl-beta-cyclodextrin (HCD). SB-334867 inhibited novel wheel blockade of the LH surge (surges blocked in 2/6 SB334867-injected animals versus 16/18 vehicle-injected animals, P<0.02) and also inhibited wheel running and circadian phase shifts, indicating that activation of orexin 1 receptors is necessary for these effects. Expt. 3 tested the hypothesis that novel wheel exposure activates orexin neurons. Proestrous hamsters were transferred at ZT 5 to a nearby room within the animal facility and were exposed to a new cage with a locked or unlocked novel wheel or left in their home cages. At ZT 8, the hamsters were anesthetized, blood was withdrawn, they were perfused with fixative and brains were removed for immunohistochemical localization of Fos, GnRH, and orexin. Exposure to a wheel, whether locked or unlocked, suppressed circulating LH concentrations at ZT 8, decreased the proportion of Fos-activated GnRH neurons, and increased Fos-immunoreactive orexin cells. Unlocked wheels had greater effects than locked wheels on all three endpoints. Thus in a familiar environment, exercise potentiated the effect of the novel wheel on Fos expression because a locked wheel was not a sufficient stimulus to block the LH surge. In conclusion, these studies indicate that novel wheel exposure activates orexin neurons and that blockade of orexin 1 receptors prevents novel wheel blockade of the LH surge. These findings are consistent with a role for both exercise and arousal in mediating novel wheel blockade of the LH surge. PMID:24727338

Chronic sciatic neuropathy in rat reduces voluntary wheel running activity with concurrent chronic mechanical allodynia

PubMed Central

Whitehead, RA; Lam, NL; Sun, MS; Sanchez, JJ; Noor, S; Vanderwall, AG; Petersen, TR; Martin, HB

2016-01-01

BACKGROUND Animal models of peripheral neuropathy produced by a number of manipulations are assessed for the presence of pathological pain states such as allodynia. While stimulus-induced behavioral assays are frequently used and important to examine allodynia (i.e. sensitivity to light mechanical touch; von Frey fiber test) other measures of behavior that reflect overall function are not only complementary to stimulus-induced responsive measures, but are also critical to gain a complete understanding of the effects of the pain model on quality of life, a clinically relevant aspect of pain on general function. Voluntary wheel running activity in rodent models of inflammatory and muscle pain is emerging as a reliable index of general function that extends beyond stimulus-induced behavioral assays. Clinically, reports of increased pain intensity occur at night, a period typically characterized with reduced activity during the diurnal cycle. We therefore examined in rats whether alterations in wheel running activity were more robust during the inactive phase compared to the active phase of their diurnal cycle in a widely used rodent model of chronic peripheral neuropathic pain, the sciatic nerve chronic constriction injury (CCI) model. METHODS In adult male Sprague Dawley rats, baseline (BL) hindpaw threshold responses to light mechanical touch were assessed using the von Frey test prior to measuring BL activity levels using freely accessible running wheels (1 hr/day for 7 sequential days) to quantify distance traveled. Running wheel activity BL values are expressed as total distance traveled (m). The overall experimental design was: following BL measures, rats underwent either sham or CCI surgery followed by repeated behavioral re-assessment of hindpaw thresholds and wheel running activity levels for up to 18 days after surgery. Specifically, separate groups of rats were assessed for wheel running activity levels (1 hr total/trial) during the onset (within first 2 hrs) of either the (1) inactive (n=8/gp) or (2) active (n = 8/gp) phase of the diurnal cycle. An additional group of CCI-treated rats (n = 8/gp) were exposed to a locked running wheel to control for the potential effects of wheel running exercise on allodynia. The 1-hr running wheel trial period was further examined at discrete 20-min intervals to identify possible pattern differences in activity during the first, middle and last portion of the 1-hr trial. The effect of neuropathy on activity levels were assessed by measuring the change from their respective BLs to distance traveled in the running wheels. RESULTS While wheel running distances between groups were not different at BL from rats examined during either the inactive phase of the diurnal cycle or active phase of the diurnal cycle, sciatic nerve CCI reduced running wheel activity levels compared to sham-operated controls during the inactive phase. Additionally, compared to sham controls, bilateral low threshold mechanical allodynia was observed at all time-points after surgical induction of neuropathy in rats with free-wheel and locked-wheel access. Allodynia in CCI compared to shams was replicated in rats whose running wheel activity was examined during the active phase of the diurnal cycle. Conversely, no significant reduction in wheel running activity was observed in CCI-treated rats compared to sham controls at any timepoint when activity levels were examined during the active diurnal phase. Lastly, running wheel activity patterns within the 1 hr trial period during the inactive phase of the diurnal cycle were relatively consistent throughout each 20 min phase. CONCLUSIONS Compared to non-neuropathic sham controls, a profound and stable reduction of running wheel activity was observed in CCI rats during the inactive phase of the diurnal cycle. A concurrent robust allodynia persisted in all rats regardless of when wheel running activity was examined or whether they ran on wheels, suggesting that acute wheel running activity does not alter chronic low intensity mechanical allodynia as measured using the von Frey fiber test. Overall, these data support that acute wheel running exercise with limited repeated exposures does not itself alter allodynia and offers a behavioral assay complementary to stimulus-induced measures of neuropathic pain. PMID:27782944

Borate-polyol complexes in aqueous solution: determination of enthalpies by thermometric titrimetry.

PubMed

Aruga, R

1985-06-01

Enthalpies for the reaction of borate with 1,2-ethanediol, 1,2-propanediol, 1,2,3-propanetriol and d-mannitol have been determined by thermometric titrimetry. From these enthalpies and equilibrium constants taken from the literature, corresponding entropies have been calculated. The data refer to aqueous solutions at 25 degrees and I = 1.0M (NaNO(3)). The results indicate reasons for the differences in the stabilities of the complexes.

14 CFR 23.511 - Ground load; unsymmetrical loads on multiple-wheel units.

Code of Federal Regulations, 2011 CFR

2011-01-01

... CATEGORY AIRPLANES Structure Ground Loads § 23.511 Ground load; unsymmetrical loads on multiple-wheel units... coefficient of friction of 0.8 applied to the main gear and its supporting structure. (b) Unequal tire loads... distribution, to the dual wheels and tires in each dual wheel landing gear unit. (c) Deflated tire loads. For...

14 CFR 23.483 - One-wheel landing conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false One-wheel landing conditions. 23.483... Ground Loads § 23.483 One-wheel landing conditions. For the one-wheel landing condition, the airplane is assumed to be in the level attitude and to contact the ground on one side of the main landing gear. In...

Rolling Reloaded

ERIC Educational Resources Information Center

Jones, Simon A.; Nieminen, John M.

2008-01-01

Not so long ago a new observation about rolling motion was described: for a rolling wheel, there is a set of points with instantaneous velocities directed at or away from the centre of the wheel; these points form a circle whose diameter connects the centre of the wheel to the wheel's point of contact with the ground (Sharma 1996 "Eur. J. Phys."…

14 CFR 27.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2014 CFR

2014-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

14 CFR 29.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2013 CFR

2013-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

14 CFR 29.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2012 CFR

2012-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

14 CFR 27.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2011 CFR

2011-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

14 CFR 29.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2014 CFR

2014-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

14 CFR 29.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2011 CFR

2011-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

14 CFR 27.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2012 CFR

2012-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

14 CFR 27.497 - Ground loading conditions: landing gear with tail wheels.

Code of Federal Regulations, 2013 CFR

2013-01-01

... be resisted by angular inertia forces. (c) Level landing attitude with all wheels contacting the... gravity; or (2) The probability of landing with initial contact on the rear wheel must be shown to be... paragraph (f)(1) of this section must be applied— (i) At the ground contact point with the wheel in the...

6. VIEW OF BORING MILL. Chuck action of locomotive wheel ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW OF BORING MILL. Chuck action of locomotive wheel Wheel weight 1200 pounds, 3'-0' diameter. Table 53' in diameter Wheel is 48'. Largest hole that can be bored is 9-1/2' plus (GE axle is 10'). - Juniata Shops, Erecting Shop & Machine Shop, East of Fourth Avenue, between Fourth & Fifth Streets, Altoona, Blair County, PA

Running Wheel for Earthworms

PubMed Central

Wilson, W. Jeffrey; Johnson, Brandon A.

2016-01-01

We describe the construction and use of a running wheel responsive to the movement of the earthworm. The wheel employs readily available, inexpensive components and is easily constructed. Movement of the wheel can be monitored visually or via standard behavioral laboratory computer interfaces. Examples of data are presented, and possibilities for use in the teaching classroom are discussed. PMID:27385934

75 FR 41920 - Agency Information Collection; Activity Under OMB Review; Airline Service Quality Performance...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-19

... and analyze air traffic delays. Wheels-up and wheels-down times are used in conjunction with departure and arrival times to show the extent of ground delays. Actual elapsed flight time, wheels-down minus wheels- up time, is compared to scheduled elapsed flight time to identify airborne delays. The reporting...

75 FR 32806 - Notice of Issuance of Final Determination Concerning Certain Upright and Recumbent Exercise Bikes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-09

... assembly, are assembled in the U.S. The primary subassemblies include the wheel assembly; the leg leveler.../shaft; the drive pulley/crank hub; the idler-arm assembly; the alternator- pulley assembly; the rear.... Pressing flange bearing into wheel using arbor press; (wheel assembly) 2. Securing insert to wheel and...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... force applied by the brake on a front wheel or a rear wheel shall not differ by more than 20 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i... Pounds or Less § 570.5 Service brake system. Unless otherwise noted, the force to be applied during...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... force applied by the brake on a front wheel or a rear wheel shall not differ by more than 20 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i... Pounds or Less § 570.5 Service brake system. Unless otherwise noted, the force to be applied during...

49 CFR 570.5 - Service brake system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... force applied by the brake on a front wheel or a rear wheel shall not differ by more than 20 percent from the force applied by the brake on the other front wheel or the other rear wheel respectively. (i... Pounds or Less § 570.5 Service brake system. Unless otherwise noted, the force to be applied during...

Considerations on the use of elastic wheels to the urban transport vehicles

NASA Astrophysics Data System (ADS)

Sebesan, Ioan; Arsene, Sorin; Manea, Ion

2018-03-01

To minimize dynamic wheel-rail interaction efforts a condition is that the unassembled mass of the vehicle is as small as possible. The elastic wheel by its construction fulfills these conditions - she has interposed between the crown and the body of the wheel, the elastic rubber elements. In this way, it can be considered that the unsupported mass is represented only by the mass of the wheel crown. Additionally, this elasticity also has a reduction effect on rolling noise. This feature makes it suitable for use on urban transport vehicles.

Electronic 4-wheel drive control device

NASA Technical Reports Server (NTRS)

Hayato, S.; Takanori, S.; Shigeru, H.; Tatsunori, S.

1984-01-01

The internal rotation torque generated during operation of a 4-wheel drive vehicle is reduced using a control device whose clutch is attached to one part of the rear-wheel drive shaft. One torque sensor senses the drive torque associated with the rear wheel drive shaft. A second sensor senses the drive torque associated with the front wheel drive shaft. Revolution count sensors sense the revolutions of each drive shaft. By means of a microcomputer, the engagement of the clutch is changed to insure that the ratio of the torque sensors remains constant.

[Fracture of the diaphyseal radius during Cyr wheel practice - an uncommon injury of wheel gymnastics].

PubMed

Kauther, M D; Rummel, S; Hussmann, B; Lendemans, S; Nast-Kolb, D; Wedemeyer, C

2011-12-01

The cyr wheel is a modified gymnastic wheel with only one ring that can lead to extreme forces on the gymnast. We report on a distal radius shaft fracture (AO 22 A 2.1) and a fracture of the styloid process of the ulna that occurred after holding on to a slipping Cyr wheel and exposition to high pressure on the lower arm. The fracture was fixed by screws and a plate. © Georg Thieme Verlag KG Stuttgart · New York.

Blocking of conditioned taste avoidance induced by wheel running.

PubMed

Pierce, W David; Heth, C Donald

2010-01-01

In Experiment 1, compared to non-reinforced presentation of a food stimulus (A-->no US), the association of a food stimulus with wheel running (A-->US) blocked subsequent avoidance of a distinctive flavor (X), when both the food and flavor were followed by wheel running (AX-->US). Experiment 2 replicated and extended the blocking effect, demonstrating that the amount of avoidance of X after AX-->wheel training depended on the correlation between A-alone trials and wheel running-the predictiveness of the A stimulus. The present study is the first to demonstrate associative blocking of conditioned taste avoidance (CTA) induced by wheel running and strongly implicates associative learning as the basis for this kind of avoidance. 2009 Elsevier B.V. All rights reserved.

Wheel-running in a transgenic mouse model of Alzheimer's disease: protection or symptom?

PubMed

Richter, Helene; Ambrée, Oliver; Lewejohann, Lars; Herring, Arne; Keyvani, Kathy; Paulus, Werner; Palme, Rupert; Touma, Chadi; Schäbitz, Wolf-Rüdiger; Sachser, Norbert

2008-06-26

Several studies on both humans and animals reveal benefits of physical exercise on brain function and health. A previous study on TgCRND8 mice, a transgenic model of Alzheimer's disease, reported beneficial effects of premorbid onset of long-term access to a running wheel on spatial learning and plaque deposition. Our study investigated the effects of access to a running wheel after the onset of Abeta pathology on behavioural, endocrinological, and neuropathological parameters. From day 80 of age, the time when Abeta deposition becomes apparent, TgCRND8 and wildtype mice were kept with or without running wheel. Home cage behaviour was analysed and cognitive abilities regarding object recognition memory and spatial learning in the Barnes maze were assessed. Our results show that, in comparison to Wt mice, Tg mice were characterised by impaired object recognition memory and spatial learning, increased glucocorticoid levels, hyperactivity in the home cage and high levels of stereotypic behaviour. Access to a running wheel had no effects on cognitive or neuropathological parameters, but reduced the amount of stereotypic behaviour in transgenics significantly. Furthermore, wheel-running was inversely correlated with stereotypic behaviour, suggesting that wheel-running may have stereotypic qualities. In addition, wheel-running positively correlated with plaque burden. Thus, in a phase when plaques are already present in the brain, it may be symptomatic of brain pathology, rather than protective. Whether or not access to a running wheel has beneficial effects on Alzheimer-like pathology and symptoms may therefore strongly depend on the exact time when the wheel is provided during development of the disease.

Characterization of a starch based desiccant wheel dehumidifier

NASA Astrophysics Data System (ADS)

Beery, Kyle Edward

Starch, cellulose, and hemicellulose have an affinity for water, and adsorb water vapor from air. Materials made from combinations of these biobased sugar polymers also have been found to possess adsorptive properties. An interesting possible application of these starch-based adsorbents is the desiccant wheel dehumidifier. The desiccant wheel dehumidifier is used in conjunction with a standard air conditioning system. In this process, ambient air is passed through a stationary section while a wheel packed with desiccant rotates through that section. The desiccant adsorbs humidity (latent load) from the air, and the air conditioning system then cools the air (sensible load). Several starch based adsorbents were developed and tested for adsorptive capacity in a new high throughput screening system. The best formulations from the high throughput screening system, also taking into account economic considerations and structural integrity, were considered for use in the desiccant wheel dehumidifier. A suitable adsorbent was chosen and formulated into a matrix structure for the desiccant wheel system. A prototype desiccant wheel system was constructed and the performance was investigated under varying regeneration temperatures and rotation speeds. The results from the experiments showed that the starch based desiccant wheel dehumidification system does transfer moisture from the inlet process stream to the outlet regeneration stream. The DESSIM model was modified for the starch based adsorbent and compared to the experimental results. Also, the results when the wheel parameters were varied were compared to the predicted results from the model. The results given by the starch based desiccant wheel system show the desired proof of concept.

Duration- and environment-dependent effects of repeated voluntary exercise on anxiety and cued fear in mice.

PubMed

Dubreucq, Sarah; Marsicano, Giovanni; Chaouloff, Francis

2015-04-01

Several studies have indicated that animal models of exercise, such as voluntary wheel running, might be endowed with anxiolytic properties. Using the light/dark test of unconditioned anxiety, we have reported that one confounding factor in the estimation of wheel running impacts on anxiety might be the housing condition of the sedentary controls. The present mouse study analyzed whether the aforementioned observation in the light/dark test (i) could be repeated in the elevated plus-maze and social interaction tests of unconditioned anxiety, (ii) extended to conditioned anxiety, as assessed during cued fear recall tests, and (iii) required unlimited daily access to the running wheel. Housing with a locked wheel or with a free wheel that allowed limited or unlimited running activity triggered anxiolysis in the light/dark test, but not in the elevated plus-maze test, compared to standard housing. In the social interaction test, the duration, but not the number, of social contacts was increased in mice provided unlimited (but not limited) access to a wheel, compared to standard housing or housing with a locked wheel. Lastly, freezing responses to a cue during fear recall tests indicated that the reduction in freezing observed in mice provided limited or unlimited access to the wheels was fully accounted for by housing with a wheel. Besides confirming that the housing condition of the sedentary controls might bias the estimation of the effects of wheel running on anxiety, this study further shows that this estimation is dependent on the test used to assess anxiety. Copyright © 2014 Elsevier B.V. All rights reserved.

Integration of uniform design and quantum-behaved particle swarm optimization to the robust design for a railway vehicle suspension system under different wheel conicities and wheel rolling radii

NASA Astrophysics Data System (ADS)

Cheng, Yung-Chang; Lee, Cheng-Kang

2017-10-01

This paper proposes a systematic method, integrating the uniform design (UD) of experiments and quantum-behaved particle swarm optimization (QPSO), to solve the problem of a robust design for a railway vehicle suspension system. Based on the new nonlinear creep model derived from combining Hertz contact theory, Kalker's linear theory and a heuristic nonlinear creep model, the modeling and dynamic analysis of a 24 degree-of-freedom railway vehicle system were investigated. The Lyapunov indirect method was used to examine the effects of suspension parameters, wheel conicities and wheel rolling radii on critical hunting speeds. Generally, the critical hunting speeds of a vehicle system resulting from worn wheels with different wheel rolling radii are lower than those of a vehicle system having original wheels without different wheel rolling radii. Because of worn wheels, the critical hunting speed of a running railway vehicle substantially declines over the long term. For safety reasons, it is necessary to design the suspension system parameters to increase the robustness of the system and decrease the sensitive of wheel noises. By applying UD and QPSO, the nominal-the-best signal-to-noise ratio of the system was increased from -48.17 to -34.05 dB. The rate of improvement was 29.31%. This study has demonstrated that the integration of UD and QPSO can successfully reveal the optimal solution of suspension parameters for solving the robust design problem of a railway vehicle suspension system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reister, D.B.; Unseren, M.A.

When a vehicle with two or more steerable drive wheels is traveling in a circle, the motion of the wheels is constrained. The wheel translational velocity divided by the radius to the center of rotation must be the same for all wheels. When the drive wheels are controlled independently using position control, the motion of the wheels may violate the constraints and the wheels may slip. Consequently, substantial errors can occur in the orientation of the vehicle. A vehicle with N drive wheels has (N - 1) constraints and one degree of freedom. We have developed a new approach tomore » the control of a vehicle with N steerable drive wheels. The novel aspect of our approach is the use of force control. To control the vehicle, we have one degree of freedom for the position on the circle and (N - 1) forces that can be used to reduce errors. Recently, Kankaanranta and Koivo developed a control architecture that allows the force and position degrees of freedom to be decoupled. In the work of Kankaanranta and Koivo the force is an exogenous input. We have made the force endogenous by defining the force in terms of the errors in satisfying the rigid body kinematic constraints. We have applied the control architecture to the HERMIES-III robot and have measured a dramatic reduction in error (more than a factor of 20) compared to motions without force control.« less

Depression of home cage wheel running: a reliable and clinically relevant method to assess migraine pain in rats.

PubMed

Kandasamy, Ram; Lee, Andrea T; Morgan, Michael M

2017-12-01

The development of new anti-migraine treatments is limited by the difficulty inassessing migraine pain in laboratory animals. Depression of activity is one of the few diagnostic criteria formigraine that can be mimicked in rats. The goal of the present study was to test the hypothesis thatdepression of home cage wheel running is a reliable and clinically relevant method to assess migraine painin rats. Adult female rats were implanted with a cannula to inject allyl isothiocyanate (AITC) onto the dura to induce migraine pain, as has been shown before. Rats recovered from implantation surgery for 8 days in cages containing a running wheel. Home cage wheel running was recorded 23 h a day. AITC and the migraine medication sumatriptan were administered in the hour prior to onset of the dark phase. Administration of AITC caused a concentration-dependent decrease in wheel running that lasted 3 h. The duration and magnitude of AITC-induced depression of wheel running was consistent following three repeated injections spaced 48 h apart. Administration of sumatriptan attenuated AITC-induced depressionof wheel running when a large dose (1 mg/kg) was administered immediately following AITC administration. Wheel running patterns did not change when sumatriptan was given to naïve rats. These data indicate that home cage wheel running is a sensitive, reliable, and clinically relevant method to assess migraine pain in the rat.

Analysis of Flexible Car Body of Straddle Monorail Vehicle

NASA Astrophysics Data System (ADS)

Zhong, Yuanmu

2018-03-01

Based on the finite element model of straddle monorail vehicle, a rigid-flexible coupling dynamic model considering vehicle body’s flexibility is established. The influence of vertical stiffness and vertical damping of the running wheel on the modal parameters of the car body is analyzed. The effect of flexible car body on modal parameters and vehicle ride quality is also studied. The results show that when the vertical stiffness of running wheel is less than 1 MN / m, the car body bounce and pitch frequency increase with the increasing of the vertical stiffness of the running wheel, when the running wheel vertical stiffness is 1MN / m or more, car body bounce and pitch frequency remained unchanged; When the vertical stiffness of the running wheel is below 1.8 MN / m, the vehicle body bounce and pitch damping ratio increase with the increasing of the vertical stiffness of the running wheel; When the running wheel vertical stiffness is 1.8MN / m or more, the car body bounce and pitch damping ratio remained unchanged; The running wheel vertical damping on the car body bounce and pitch frequency has no effect; Car body bounce and pitch damping ratio increase with the increasing of the vertical damping of the running wheel. The flexibility of the car body has no effect on the modal parameters of the car, which will improve the vehicle ride quality index.

NCHRP project 20-07/task 361 : hamburg wheel-track test equipment requirements and improvements to AASHTO T 324 : research project capsule.

DOT National Transportation Integrated Search

2015-02-01

The Loaded Wheel Test (LWT) is a laboratory-controlled rut depth test that uses loaded wheel(s) : to apply a moving load on hot-mix and warm-mix asphalt (HMA and WMA) specimens to simulate : tra c load applied on asphalt pavements. In the 1970s He...

The Goal Wheel: Adapting Navajo Philosophy and the Medicine Wheel to Work with Adolescents

ERIC Educational Resources Information Center

Garner, Holly; Bruce, Mary Alice; Stellern, John

2011-01-01

The purpose of this article is to describe a group counseling model that is based on the indigenous medicine wheel as well as Navajo philosophy by which to help troubled adolescents restore harmony and balance in their lives, through establishing goals and sequential steps to accomplish these goals. The authors call this model the Goal Wheel. A…

Control of a Wheeled Transport Robot with Two Steerable Wheels

NASA Astrophysics Data System (ADS)

Larin, V. B.

2017-09-01

The control of a system with one actuator failed is studied. The problem of control of a wheeled transport robot with two steerable wheels of which the rear one is stuck (its drive has failed) is solved. An algorithm for controlling the system in this situation is proposed. The effectiveness of the algorithm is demonstrated by way of an example.

Four-Wheel Vehicle Suspension System

NASA Technical Reports Server (NTRS)

Bickler, Donald B.

1990-01-01

Four-wheel suspension system uses simple system of levers with no compliant components to provide three-point suspension of chassis of vehicle while maintaining four-point contact with uneven terrain. Provides stability against tipping of four-point rectangular base, without rocking contact to which rigid four-wheel frame susceptible. Similar to six-wheel suspension system described in "Articulated Suspension Without Springs" (NPO-17354).

Guide To Mobile Aircraft Arresting System Installation - Air Force Handbook 10-222, Volume 8

DTIC Science & Technology

2000-03-01

38. Anchor Connection at Right Rear Wheel .................................................66 39. Store Tire Away from Runway – Right MAAS Trailer...MAAS Trailer .......68 42. Right Rear Wheel Anchor Point – Right MAAS Trailer.......................68 43. Right Rear Wheel Anchor Point Using...Rear Wheel .......................................73 47. Store Tire Away from Runway – Both MAAS Trailers ........................74 48. Left Rear

77 FR 12812 - Steel Wheels From the People's Republic of China: Notice of Preliminary Affirmative Determination...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-02

... separately. These products are used with both tubed and tubeless tires. Steel wheels, whether or not attached to tires or axles, are included. However, if the steel wheels are imported as an assembly attached to tires or axles, the tire or axle is not covered by the scope. The scope includes steel wheels, discs...

29 CFR 1910.177 - Servicing multi-piece and single piece rim wheels.

Code of Federal Regulations, 2011 CFR

2011-07-01

... rim wheel onto a vehicle axle hub. Removing means the opposite of installing. Mounting a tire means... 29 Labor 5 2011-07-01 2011-07-01 false Servicing multi-piece and single piece rim wheels. 1910.177... § 1910.177 Servicing multi-piece and single piece rim wheels. (a) Scope. (1) This section applies to the...

77 FR 33808 - Agency Information Collection; Activity Under OMB Review: Airline Service Quality Performance...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-07

... Administration uses Part 234 data to pinpoint and analyze air traffic delays. Wheels-up and wheels-down times are... elapsed flight time, wheels-down minus wheels- up time, is compared to scheduled elapsed flight time to... the air network, which enables the FAA to study the ripple effects of delays at hub airports. The data...

29 CFR 1910.177 - Servicing multi-piece and single piece rim wheels.

Code of Federal Regulations, 2014 CFR

2014-07-01

... means the transfer and attachment of an assembled rim wheel onto a vehicle axle hub. Removing means the... 29 Labor 5 2014-07-01 2014-07-01 false Servicing multi-piece and single piece rim wheels. 1910.177... § 1910.177 Servicing multi-piece and single piece rim wheels. (a) Scope. (1) This section applies to the...

29 CFR 1910.177 - Servicing multi-piece and single piece rim wheels.

Code of Federal Regulations, 2010 CFR

2010-07-01

... rim wheel onto a vehicle axle hub. Removing means the opposite of installing. Mounting a tire means... 29 Labor 5 2010-07-01 2010-07-01 false Servicing multi-piece and single piece rim wheels. 1910.177... § 1910.177 Servicing multi-piece and single piece rim wheels. (a) Scope. (1) This section applies to the...

29 CFR 1910.177 - Servicing multi-piece and single piece rim wheels.

Code of Federal Regulations, 2013 CFR

2013-07-01

... means the transfer and attachment of an assembled rim wheel onto a vehicle axle hub. Removing means the... 29 Labor 5 2013-07-01 2013-07-01 false Servicing multi-piece and single piece rim wheels. 1910.177... § 1910.177 Servicing multi-piece and single piece rim wheels. (a) Scope. (1) This section applies to the...

29 CFR 1910.177 - Servicing multi-piece and single piece rim wheels.

Code of Federal Regulations, 2012 CFR

2012-07-01

... means the transfer and attachment of an assembled rim wheel onto a vehicle axle hub. Removing means the... 29 Labor 5 2012-07-01 2012-07-01 false Servicing multi-piece and single piece rim wheels. 1910.177... § 1910.177 Servicing multi-piece and single piece rim wheels. (a) Scope. (1) This section applies to the...

Power transmission device for four wheel drive vehicle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iwatsuki, T.; Kawamoto, M.; Kano, T.

This patent describes a power transmission device with an improved differential motion limiting mechanism for a four wheel drive vehicle having automatic transmission means, front wheel differential gear means, differential motion limiting means and transfer unit means including center differential gear means, comprising: a first gear mount casing having a gear adapted to mesh with an output of a transmission; a differential motion limiting device arranged together with a front wheel differential gear in the first gear mount casing. The front wheel differential gear having a first diff-carrier and the differential motion limiting device comprising a hydraulic friction clutch formore » engaging and disengaging the first gear mount casing with the first diff-carrier of the front wheel differential gear; a second gear mount casing disposed coaxially with respect to the first gear mount casing; and a transfer unit including a center differential gear arranged in the second gear mount casing, the center differential gear comprising a second diff-carrier coupled with the first gear mount casing, a first side gear coupled with the first diff-carrier of the front wheel differential gear, and a second side gear coupled with the second gear mount casing for transmitting power to the rear wheels.« less

Judging rolling wheels: Dynamic and kinematic aspects of rotation-translation coupling

NASA Technical Reports Server (NTRS)

Hecht, Heiko

1993-01-01

Four experiments were carried out to investigate observers' abilities to judge rolling motions. The experiments were designed to assess whether two important aspects of such motions are appreciated: the kinematic coupling of rotation and translation, and the dynamic effects of gravity. Different motion contexts of rolling wheels were created using computer-generated displays. The first experiment involved wheels rolling down an inclined plane. Observers spontaneously appreciated the anomaly of wheels that failed to accelerate, but they were not able to differentiate between different acceleration functions. Moreover, their judgements were almost exclusively based on the translation component of the rolling motion, neglecting the rotation component. In a second experiment it was found that observers could accurately estimate the perimeter of various objects. Thus, their inability to consider rotation information is not attributable to misperceptions of the geometry of wheels. In a third experiment the finding that rolling wheels appear to overrotate was replicated; however, findings from this experiment also showed, together with those from a fourth experiment, that observers are able to make very accurate judgments about translation-rotation coupling in rolling wheels when information is provided about the orientation of the wheel and the texture of the surface on which it rolls.

Judging rolling wheels: dynamic and kinematic aspects of rotation-translation coupling.

PubMed

Hecht, H

1993-01-01

Four experiments were carried out to investigate observers' abilities to judge rolling motions. The experiments were designed to assess whether two important aspects of such motions are appreciated: the kinematic coupling of rotation and translation, and the dynamic effects of gravity. Different motion contexts of rolling wheels were created using computer-generated displays. The first experiment involved wheels rolling down an inclined plane. Observers spontaneously appreciated the anomaly of wheels that failed to accelerate, but they were not able to differentiate between different acceleration functions. Moreover, their judgments were almost exclusively based on the translation component of the rolling motion, neglecting the rotation component. In a second experiment it was found that observers could accurately estimate the perimeter of various objects. Thus, their inability to consider rotation information is not attributable to misperceptions of the geometry of wheels. In a third experiment the finding that rolling wheels appear to overrotate was replicated; however, findings from this experiment also showed, together with those from a fourth experiment, that observers are able to make very accurate judgments about translation-rotation coupling in rolling wheels when information is provided about the orientation of the wheel and the texture of the surface on which it rolls.

Automated home cage observations as a tool to measure the effects of wheel running on cage floor locomotion.

PubMed

de Visser, Leonie; van den Bos, Ruud; Spruijt, Berry M

2005-05-28

This paper introduces automated observations in a modular home cage system as a tool to measure the effects of wheel running on the time distribution and daily organization of cage floor locomotor activity in female C57BL/6 mice. Mice (n = 16) were placed in the home cage system for 6 consecutive days. Fifty percent of the subjects had free access to a running wheel that was integrated in the home cage. Overall activity levels in terms of duration of movement were increased by wheel running, while time spent inside a sheltering box was decreased. Wheel running affected the hourly pattern of movement during the animals' active period of the day. Mice without a running wheel, in contrast to mice with a running wheel, showed a clear differentiation between novelty-induced and baseline levels of locomotion as reflected by a decrease after the first day of introduction to the home cage. The results are discussed in the light of the use of running wheels as a tool to measure general activity and as an object for environmental enrichment. Furthermore, the possibilities of using automated home cage observations for e.g. behavioural phenotyping are discussed.

Interaction between moving tandem wheels and an infinite rail with periodic supports - Green's matrices of the track method in stationary reference frame

NASA Astrophysics Data System (ADS)

Mazilu, Traian

2017-08-01

This paper approaches the issue of the interaction between moving tandem wheels and an infinite periodically supported rail and points out at the basic characteristics in the steady-state interaction behaviour and in the interaction in the presence of the rail random irregularity. The rail is modelled as an infinite Timoshenko beam resting on supports which are discretely modelling the inertia of the sleepers and ballast and also the viscoelastic features of the rail pads, the ballast and the subgrade. Green‧s matrices of the track method in stationary reference frame were applied so as to conduct the time-domain analysis. This method allows to consider the nonlinearities of the wheel/rail contact and the Doppler effect. The study highlights certain aspects regarding the influence of the wheel base on the wheels/rail contact forces, particularly at the parametric resonance, due to the coincidence between the wheel/rail natural frequency and the passing frequency and also when the rail surface exhibits random irregularity. It has been shown that the wheel/rail dynamic behaviour is less intense when the wheel base equals integer multiple of the sleeper bay.

Naloxone attenuates the conditioned place preference induced by wheel running in rats.

PubMed

Lett, B T; Grant, V L; Koh, M T

2001-02-01

Pairings, during which an episode of wheel running is followed by confinement in a distinctive place, produce conditioned place preference (CPP) in rats. This finding indicates that wheel running has a rewarding effect that outlasts the activity itself. In two similar experiments, we tested the hypothesis that this rewarding effect of wheel running is mediated by endogenous opioids. During a paired trial, the rats in the naloxone group were first allowed to wheel run for 2 h, then injected with naloxone (0.5 or 0.1 mg/kg in Experiments 1 and 2, respectively), and 10 min later placed in a distinctive chamber. During an unpaired trial, these rats were confined in an adjoining chamber without wheel running. Naloxone was injected before placement in both chambers, so that if naloxone-induced conditioned place aversion occurred, it would have counteracting effects on performance during the preference test. The rats in the saline group were similarly treated, except that saline was injected instead of naloxone. CPP occurred in the saline group, but not in the naloxone group. Thus, naloxone attenuated the CPP induced by wheel running. This finding supports the hypothesis that the rewarding effect of wheel running is mediated by endogenous opioids.

Hypersonic aerothermodynamic and scramjet research using high enthalpy shock tunnel

NASA Astrophysics Data System (ADS)

Itoh, K.; Ueda, S.; Tanno, H.; Komuro, T.; Sato, K.

A high enthalpy shock tunnel is a potential facility for gaining knowledge to develop modern aerothermodynamic and propulsion technologies. The largest high enthalpy shock tunnel HIEST was built at NAL Kakuda in 1997, aiming for aerothermodynamic tests of Japan's space vehicle HOPE and scramjet propulsion systems. Selected topics from the experimental studies carried out using HIEST so far, such as the nonequilibrium aerodynamics of HOPE, the surface catalytic effect on aerodynamic heating and scramjet performance are described.

Thermodynamics of cosolvent action: phenacetin, salicylic acid and probenecid.

PubMed

Peña, M A; Escalera, B; Reíllo, A; Sánchez, A B; Bustamante, P

2009-03-01

The solubility of phenacetin, salicylic acid, and probenecid in ethanol-water and ethanol-ethyl acetate mixtures at several temperatures (15-40 degrees C) was measured. The solubility profiles are related to medium polarity changes. The apparent thermodynamic magnitudes and enthalpy-entropy relationships are related to the cosolvent action. Salicylic acid and probenecid show a single peak against the solubility parameter delta(1) of both solvent mixtures, at 40% (delta(1) = 21.70 MPa(1/2)) and 30% (delta(1) = 20.91 MPa(1/2)) ethanol in ethyl acetate, respectively. Phenacetin displays two peaks at 60% ethanol in ethyl acetate (23.30 MPa(1/2)) and 90% ethanol in water (delta(1) = 28.64 MPa(1/2)). The apparent enthalpies of solution display a maximum at 30% (phenacetin and salicylic acid) and 40% (probenecid) ethanol in water, respectively. Two different mechanisms, entropy at low ethanol ratios, and enthalpy at high ethanol ratios control the solubility enhancement in the aqueous mixture. In the nonaqueous mixture (ethanol-ethyl acetate) enthalpy is the driving force throughout the whole solvent composition for salicylic acid and phenacetin. For probenecid, the dominant mechanism shifts from entropy to enthalpy as the ethanol in ethyl acetate concentration increases. The enthalpy-entropy compensation plots corroborate the different mechanisms involved in the solubility enhancement by cosolvents. (c) 2008 Wiley-Liss, Inc. and the American Pharmacists Association

A Wavelet-Based Methodology for Grinding Wheel Condition Monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liao, T. W.; Ting, C.F.; Qu, Jun

2007-01-01

Grinding wheel surface condition changes as more material is removed. This paper presents a wavelet-based methodology for grinding wheel condition monitoring based on acoustic emission (AE) signals. Grinding experiments in creep feed mode were conducted to grind alumina specimens with a resinoid-bonded diamond wheel using two different conditions. During the experiments, AE signals were collected when the wheel was 'sharp' and when the wheel was 'dull'. Discriminant features were then extracted from each raw AE signal segment using the discrete wavelet decomposition procedure. An adaptive genetic clustering algorithm was finally applied to the extracted features in order to distinguish differentmore » states of grinding wheel condition. The test results indicate that the proposed methodology can achieve 97% clustering accuracy for the high material removal rate condition, 86.7% for the low material removal rate condition, and 76.7% for the combined grinding conditions if the base wavelet, the decomposition level, and the GA parameters are properly selected.« less

Design and performance tests of a distributed power-driven wheel loader

NASA Astrophysics Data System (ADS)

Jin, Xiaolin; Shi, Laide; Bian, Yongming

2010-03-01

An improved ZLM15B distributed power-driven wheel loader was designed, whose travel and brake system was accomplished by two permanent magnet synchronous motorized-wheels instead of traditional mechanical components, and whose hydraulic systems such as the working device system and steering system were both actuated by an induction motor. All above systems were flexibly coupled with 3-phase 380VAC electric power with which the diesel engine power is replaced. On the level cement road, traveling, braking, traction and steering tests were carried out separately under non-load and heavy-load conditions. Data show that machine speed is 5 km/h around and travel efficiency of motorized-wheels is above 95%; that machine braking deceleration is between 0.5 and 0.64 m/s2 but efficiency of motorized-wheels is less than 10%; that maximum machine traction is above 2t while efficiency of motorized-wheels is more than 90% and that adaptive differential steering can be smoothly achieved by motorized-wheels.

Design and performance tests of a distributed power-driven wheel loader

NASA Astrophysics Data System (ADS)

Jin, Xiaolin; Shi, Laide; Bian, Yongming

2009-12-01

An improved ZLM15B distributed power-driven wheel loader was designed, whose travel and brake system was accomplished by two permanent magnet synchronous motorized-wheels instead of traditional mechanical components, and whose hydraulic systems such as the working device system and steering system were both actuated by an induction motor. All above systems were flexibly coupled with 3-phase 380VAC electric power with which the diesel engine power is replaced. On the level cement road, traveling, braking, traction and steering tests were carried out separately under non-load and heavy-load conditions. Data show that machine speed is 5 km/h around and travel efficiency of motorized-wheels is above 95%; that machine braking deceleration is between 0.5 and 0.64 m/s2 but efficiency of motorized-wheels is less than 10%; that maximum machine traction is above 2t while efficiency of motorized-wheels is more than 90% and that adaptive differential steering can be smoothly achieved by motorized-wheels.

OCILOW-Wheeled Platform Controls Executable Set

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jansen, John F.

2005-11-30

The OCILOW Controls Executable Set is the complete set of machine executable instructions to control the motion of wheeled platforms that incorporate Off-Centered In-Line Omni-directional Wheels (OCILOW). The controls utilize command signals for the desired motion of the platform (X, Y and Theta) and calculate and control the steering and rolling motion required of each OCILOW wheels to achieve the desired translational and rotational platform motion. The controls utilize signals from the wheel steering and rolling resolvers, and from three load cells located at each wheels, to coordinate the motion of all wheels, while respecting their non-holonomic constraints (i.e., keepingmore » internal stresses and slippage due to possible errors, uneven floors, bumps, misalignment, etc. bounded). The OCILOW Controls Executable Set, which is copyrighted here, is an embodiment of the generic OCILOW algorithms (patented separately) developed specifically for controls of the Proof-of-Principle-Transporter (POP-T) system that has been developed to demonstrate the overall OCILOW controls feasibility and capabilities.« less

Method for surmounting an obstacle by a robot vehicle

NASA Technical Reports Server (NTRS)

Wilcox, Brian H. (Inventor); Ohm, Timothy R. (Inventor)

1994-01-01

Surmounting obstacles in the path of a robot vehicle is accomplished by rotating the wheel forks of the vehicle about their transverse axes with respect to the vehicle body so as to shift most of the vehicle weight onto the rear wheels, and then driving the vehicle forward so as to drive the now lightly-loaded front wheels (only) over the obstacle. Then, after the front wheels have either surmounted or completely passed the obstacle (depending upon the length of the obstacle), the forks are again rotated about their transverse axes so as to shift most of the vehicle weight onto the front wheels. Then the vehicle is again driven forward so as to drive the now lightly-loaded rear wheels over the obstacle. Once the obstacle has been completely cleared and the vehicle is again on relatively level terrain, the forks are again rotated so as to uniformly distribute the vehicle weight between the front and rear wheels.

Biomechanics of liver injury by steering wheel loading.

PubMed

Lau, I V; Horsch, J D; Viano, D C; Andrzejak, D V

1987-03-01

Abdominal injury induced by steering wheel contact at a velocity of 32 km/hr was investigated using anesthetized swine as the surrogate on a Hyge sled. The lower rim of the wheel was positioned 5 cm below the xyphoid. By varying wheel stiffness, wheel orientation, and column angle, resultant abdominal injury ranged from fatal or critical to minor or none. Wheel stiffness was found to be the primary determinant of abdominal injury severity. The mechanism of abdominal injury was identified to be the rim impacting the abdomen and exceeding a combined velocity and compression sensitive tolerance limit. Abdominal injury occurred within the initial 15 ms of wheel contact before whole body movement of the surrogate of column compression, which were initiated by hub contact with the thorax. The severity of abdominal injury correlated with the peak viscous response which can be represented by the product of the instantaneous velocity of abdominal deformation and abdominal compression. It did not correlate with spinal acceleration.

A versatile 50 ft-lb-sec reaction wheel for TRMM and XTE missions

NASA Astrophysics Data System (ADS)

Bialke, Bill

A 50 ft-lb-sec Reaction Wheel is being manufactured by ITHACO, Inc. for NASA's X-ray Timing Explorer (XTE) and Tropical Rainfall Measuring Mission (TRMM) missions, using the same mechanical assemblies as a similar Reaction Wheel developed by ITHACO for the Air Force's Advanced Research and Global Observation Satellite (ARGOS) (P91-1) mission. The versatile design allows variation in motor torque and speed capability with no mechanical modifications. State of the art ball bearing technology is combined with flight proven materials and conventional fabrication techniques to produce a relaible and manufacturable wheel assembly. An ironless armature brushless DC motor is incorporated for high efficiency and minimum weight. Comprehensive tradeoff analyses from the Reaction Wheel development are discussed for each component, and performance characteristics are presented for design variations from a high torque Reaction Wheel used in a three axis stabilized spacecraft to a low torque Momentum Wheel used in a momentum biased attitude Control System.

Wheel Installation

NASA Image and Video Library

2010-07-07

In this picture, the Curiosity rover sports a set of six new wheels. The wheels were installed on June 28 and 29 in the Spacecraft Assembly Facility at NASA Jet Propulsion Laboratory, Pasadena, Calif.

Computational investigation of enthalpy-entropy compensation in complexation of glycoconjugated bile salts with β-cyclodextrin and analogs.

PubMed

Tidemand, Kasper D; Schönbeck, Christian; Holm, René; Westh, Peter; Peters, Günther H

2014-09-18

The inclusion complexes of glycoconjugated bile salts with β-cyclodextrin (β-CD) and 2-hydroxypropyl-β-cyclodextrins (HP-β-CD) in aqueous solution were investigated by molecular dynamics simulations to provide a molecular explanation of the experimentally observed destabilizing effect of the HP substituents. Good agreement with experimental data was found with respect to penetration depths of CDs. An increased degree of HP substitution (DS) resulted in an increased probability of blocking the cavity opening, thereby hindering the bile salt from entering CD. Further, the residence time of water molecules in the cavity increased with the DS. Release of water from the cavity resulted in a positive enthalpy change, which correlates qualitatively with the experimentally determined increase in complexation enthalpy and contributes to the enthalpy-entropy compensation. The positive change in complexation entropy with DS was not able to compensate for this unfavorable change in enthalpy induced by the HP substituents, resulting in a destabilizing effect. This was found to originate from fixation of the HP substituents and decreased free rotation of the bile salts within the CD cavities.

An Examination of the Phase Transition Thermodynamics of (S)- and (RS)-Naproxen as a Basis for the Design of Enantioselective Crystallization Processes.

PubMed

Buchholz, Hannes; Emel'yanenko, Vladimir N; Lorenz, Heike; Verevkin, Sergey P

2016-05-01

A detailed experimental analysis of the phase transition thermodynamics of (S)-naproxen and (RS)-naproxen is reported. Vapor pressures were determined experimentally via the transpiration method. Sublimation enthalpies were obtained from the vapor pressures and from independent TGA measurements. Thermodynamics of fusion which have been well-studied in the literature were systematically remeasured by DSC. Both sublimation and fusion enthalpies were adjusted to one reference temperature, T = 298 K, using measured heat capacities of the solid and the melt phase by DSC. Average values from the measurements and from literature data were suggested for the sublimation and fusion enthalpies. In order to prove consistency of the proposed values the vaporization enthalpies obtained by combination of both were compared to vaporization enthalpies obtained by the group-additivity method and the correlation-gas chromatography method. The importance of reliable and precise phase transition data for thermochemical calculations such as the prediction of solid/liquid phase behaviour of chiral compounds is highlighted. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Protonation enthalpies of metal oxides from high temperature electrophoresis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez-Santiago, V; Fedkin, Mark V.; Lvov, Serguei N.

2012-01-01

Surface protonation reactions play an important role in the behavior of mineral and colloidal systems, specifically in hydrothermal aqueous environments. However, studies addressing the reactions at the solid/liquid interface at temperatures above 100 C are scarce. In this study, newly and previously obtained high temperature electrophoresis data (up to 260 C) zeta potentials and isoelectric points for metal oxides, including SiO2, SnO2, ZrO2, TiO2, and Fe3O4, were used in thermodynamic analysis to derive the standard enthalpies of their surface protonation. Two different approaches were used for calculating the protonation enthalpy: one is based on thermodynamic description of the 1-pKa modelmore » for surface protonation, and another one on a combination of crystal chemistry and solvation theories which link the relative permittivity of the solid phase and the ratio of the Pauling bond strength and bond length to standard protonation enthalpy. From this analysis, two expressions relating the protonation enthalpy to the relative permittivity of the solid phase were obtained.« less

Protonation enthalpies of metal oxides from high temperature electrophoresis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez-Santiago, V; Fedkin, Mark V; Lvov, Serguei N.

2012-01-01

Surface protonation reactions play an important role in the behavior of mineral and colloidal systems, specifically in hydrothermal aqueous environments. However, studies addressing the reactions at the solid/liquid interface at temperatures above 100 C are scarce. In this study, newly and previously obtained high temperature electrophoresis data (up to 260 C) - zeta potentials and isoelectric points - for metal oxides, including SiO{sub 2}, SnO{sub 2}, ZrO{sub 2}, TiO{sub 2}, and Fe{sub 3}O{sub 4}, were used in thermodynamic analysis to derive the standard enthalpies of their surface protonation. Two different approaches were used for calculating the protonation enthalpy: one ismore » based on thermodynamic description of the 1-pKa model for surface protonation, and another one - on a combination of crystal chemistry and solvation theories which link the relative permittivity of the solid phase and the ratio of the Pauling bond strength and bond length to standard protonation enthalpy. From this analysis, two expressions relating the protonation enthalpy to the relative permittivity of the solid phase were obtained.« less

A flow calorimeter for determining combustion efficiency from residual enthalpy of exhaust gases

NASA Technical Reports Server (NTRS)

Evans, Albert; Hibbard, Robert R

1954-01-01

A flow calorimeter for determining the combustion efficiency of turbojet and ram-jet combustors from measurement of the residual enthalpy of combustion of the exhaust gas is described. Briefly, the calorimeter catalytically oxidizes the combustible constituents of exhaust-gas samples, and the resultant temperature rise is measured. This temperature rise is related to the residual enthalpy of combustion of the sample by previous calibration of the calorimeter. Combustion efficiency can be calculated from a knowledge of the residual enthalpy of the exhaust gas and the combustor input enthalpy. An accuracy of +-0.2 Btu per cubic foot was obtained with prepared fuel-air mixtures, and the combustion efficiencies of single turbojet combustors measured by both the flow-calorimeter and heat-balance methods compared within 3 percentage units. Flow calorimetry appears to be a suitable method for determining combustion efficiencies at high combustor temperatures where ordinary thermocouples cannot be used. The method is fundamentally more accurate than heat-balance methods at high combustion efficiencies and can be used to verify near-100-percent efficiency data.

Molar volume, excess enthalpy, and Prigogine-Defay ratio of some silicate glasses with different (P,T) histories.

PubMed

Wondraczek, Lothar; Behrens, Harald

2007-10-21

Structural relaxation in silicate glasses with different (p,T) histories was experimentally examined by differential scanning calorimetry and measurements of molar volume under ambient pressure. Temperature and pressure-dependent rates of changes in molar volume and generation of excess enthalpy were determined for sodium trisilicate, soda lime silicate, and sodium borosilicate (NBS) compositions. From the derived data, Prigogine-Defay ratios are calculated and discussed. Changes of excess enthalpy are governed mainly by changes in short-range structure, as is shown for NBS where boron coordination is highly sensitive to pressure. For all three glasses, it is shown how the relaxation functions that underlie volume, enthalpy, and structural relaxation decouple for changes in cooling rates and pressure of freezing, respectively. The magnitude of the divergence between enthalpy and volume may be related to differences in structural sensitivity to changes in the (p,V,T,t) space on different length scales. The findings suggest that the Prigogine-Defay ratio is related to the magnitude of the discussed decoupling effect.

A study of the vaporization enthalpies of some 1-substituted imidazoles and pyrazoles by correlation-gas chromatography.

PubMed

Lipkind, Dmitry; Plienrasri, Chatchawat; Chickos, James S

2010-12-23

The vaporization enthalpies of 1-methyl-, 1-ethyl-, 1-phenyl-, and 1-benzylimidazole, 1-methyl- and 1-phenylpyrazole, and trans-azobenzene are evaluated by correlation-gas chromatography (C-GC) using a variety of azines and diazines as standards. The vaporization enthalpies obtained by C-GC when compared to literature values are approximately 14 kJ·mol(-1) smaller for the imidazoles and 6 kJ·mol(-1) smaller for the pyrazoles. The literature vaporization enthalpies of 1-methylpyrrole and 1-methylindole, two closely related compounds with one less nitrogen, are reproduced by C-GC. These results suggest that the magnitude of the intermolecular interactions present in 1-substituted imidazoles and pyrazoles are significantly larger than the those present in the reference compounds and greater than or equal in magnitude to the enhanced intermolecular interactions observed previously in aromatic 1,2-diazines. The vaporization enthalpy and vapor pressure of a trans-1,2-diazine, trans-azobenzene, measured by C-GC using similar standards reproduced the literature values within experimental error.

A new method for the determination of vaporization enthalpies of ionic liquids at low temperatures.

PubMed

Verevkin, Sergey P; Zaitsau, Dzmitry H; Emelyanenko, Vladimir N; Heintz, Andreas

2011-11-10

A new method for the determination of vaporization enthalpies of extremely low volatile ILs has been developed using a newly constructed quartz crystal microbalance (QCM) vacuum setup. Because of the very high sensitivity of the QCM it has been possible to reduce the average temperature of the vaporization studies by approximately 100 K in comparison to other conventional techniques. The physical basis of the evaluation procedure has been developed and test measurements have been performed with the common ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide [C(2)mim][NTf(2)] extending the range of measuring vaporization enthalpies down to 363 K. The results obtained for [C(2)mim][NTf(2)] have been tested for thermodynamic consistency by comparison with data already available at higher temperatures. Comparison of the temperature-dependent vaporization enthalpy data taken from the literature show only acceptable agreement with the heat capacity difference of -40 J K(-1) mol(-1). The method developed in this work opens also a new way to obtain reliable values of vaporization enthalpies of thermally unstable ionic liquids.

Electronic gap sensor and method

DOEpatents

Williams, R.S.; King, E.L.; Campbell, S.L.

1991-08-06

Disclosed are an apparatus and method for regulating the gap between a casting nozzle and a casting wheel in which the gap between the casting nozzle and the casting wheel is monitored by means of at least one sensing element protruding from the face of the casting nozzle. The sensing element is preferably connected to a voltage source and the casting wheel grounded. When the sensing element contacts the casting wheel, an electric circuit is completed. The completion of the circuit can be registered by an indicator, and the presence or absence of a completed circuit indicates the relative position of the casting nozzle to the casting wheel. The relative positions of the casting nozzle and casting wheel can thereby be selectively adjusted to continually maintain a predetermined distance between their adjacent surfaces. 5 figures.

Lightweight design and analysis of automobile wheel based on bending and radial loads

NASA Astrophysics Data System (ADS)

Jiang, X.; Lyu, R.; Fukushima, Y.; Otake, M.; Ju, D. Y.

2018-06-01

Lightweighting of automobile vehicle is a significant application trends, using magnesium alloy wheels is a valuable way. This article discusses design of a new model of automobile wheel. Then bending test and radial test finite element model were established. Considering three different materials namely magnesium alloy, aluminium alloy and steel, the stress and strain performances of each material can be obtained. Through evaluating and analyzing model in bending test and radial test, we obtained the reasonable and superior results for magnesium alloy wheel. The results of the equivalent stress and deformation were compared, the magnesium alloy wheel practicality has been confirmed. This research predicts the reliability of the structural design, some valuable references are provided for the design and development of magnesium alloy wheel.

Electronic differential control of 2WD electric vehicle considering steering stability

NASA Astrophysics Data System (ADS)

Hua, Yiding; Jiang, Haobin; Geng, Guoqing

2017-03-01

Aiming at the steering wheel differential steering control technology of rear wheel independent driving electric wheel, considering the assisting effect of electronic differential control on vehicle steering, based on the high speed steering characteristic of electric wheel car, the electronic differential speed of auxiliary wheel steering is also studied. A yaw moment control strategy is applied to the vehicle at high speed. Based on the vehicle stability reference value, yaw rate is used to design the fuzzy controller to distribute the driving wheel torque. The simulation results show that the basic electronic differential speed function is realized based on the yaw moment control strategy, while the vehicle stability control is improved and the driving safety is enhanced. On the other hand, the torque control strategy can also assist steering of vehicle.

Control of wheeled mobile robot in restricted environment

NASA Astrophysics Data System (ADS)

Ali, Mohammed A. H.; En, Chang Yong

2018-03-01

This paper presents a simulation and practical control system for wheeled mobile robot in restricted environment. A wheeled mobile robot with 3 wheels is fabricated and controlled by proportional derivative active force control (PD-AFC) to move in a pre-planned restricted environment to maintain the tracking errors at zero level. A control system with two loops, outer by PD controller and inner loop by Active Force Control, are designed to control the wheeled mobile robot. Fuzzy logic controller is implemented in the Active force Control to estimate the inertia matrix that will be used to calculate the actual torque applied on the wheeled mobile robot. The mobile robot is tested in two different trajectories, namely are circular and straight path. The actual path and desired path are compared.

Three dimensional modeling and dynamic analysis of four-wheel-steering vehicles

NASA Astrophysics Data System (ADS)

Hu, Haiyan; Han, Qiang

2003-02-01

The paper presents a nonlinear dynamic model of 9 degrees of freedom for four-wheel-steering vehicles. Compared with those in previous studies, this model includes the pitch and roll of the vehicle body, the motion of 4 wheels in the accelerating or braking process, the nonlinear coupling of vehicle body and unsprung part, as well as the air drag and wind effect. As a result, the model can be used for the analysis of various maneuvers of the four-wheel-steering vehicles. In addition, the previous models can be considered as a special case of this model. The paper gives some case studies for the dynamic performance of a four-wheel-steering vehicle under step input and saw-tooth input of steering angle applied on the front wheels, respectively.

Electronic gap sensor and method

DOEpatents

Williams, Robert S.; King, Edward L.; Campbell, Steven L.

1991-01-01

An apparatus and method for regulating the gap between a casting nozzle and a casting wheel in which the gap between the casting nozzle and the casting wheel is monitored by means of at least one sensing element protruding from the face of the casting nozzle. The sensing element is preferably connected to a voltage source and the casting wheel grounded. When the sensing element contacts the casting wheel, an electric circuit is completed. The completion of the circuit can be registered by an indicator, and the presence or absence of a completed circuit indicates the relative position of the casting nozzle to the casting wheel. The relative positions of the casting nozzle and casting wheel can thereby be selectively adjusted to continually maintain a predetermined distance between their adjacent surfaces.

Rotor bore and turbine rotor wheel/spacer heat exchange flow circuit

DOEpatents

Caruso, Philip M.; Eldrid, Sacheverel Quentin; Ladhani, Azad A.; DeMania, Alan Richard; Palmer, Gene David; Wilson, Ian David; Rathbun, Lisa Shirley; Akin, Robert Craig

2002-01-01

In a turbine having closed-circuit steam-cooling passages about the rim of the rotor during steady-state operation, compressor discharge air is supplied to the rotor bore for passage radially outwardly into the wheel space cavities between the wheels and spacers. Communicating slots and channels in the spacers and wheels at circumferentially spaced positions enable egress of the compressor discharge air into the hot gas flow path. At turbine startup, cooling air flows through the closed-circuit steam passages to cool the outer rim of the rotor while compressor discharge air pre-warms the wheels and spacers. At steady-state, cooling steam is supplied in the closed-circuit steam-cooling passages and compressor discharge air is supplied through the bore and into the wheel space cavities to cool the rotor.

Influence of the contact roughness upon railway monobloc wheel acoustic behaviour on virtual prototyping approach

NASA Astrophysics Data System (ADS)

Todorov, George; Kamberov, Konstantin; Kralov, Ivan; Ignatov, Ignat

2017-12-01

In this study the virtual prototyping is used for evaluation the influence of the contact roughness upon the acoustic behaviour evaluation of railway monobloc wheel. The proposed procedure covers requirements of the European Standard EN 13979-1 "Wheels and bogies - Monobloc wheels". The main advantage of the acoustic assessment based on the virtual engineering technics - absence of the expensive and time consuming physical tests, is sown. The real industrial-project example is presented and comparison of the numerical and experimental results is used for acoustic behaviour assessment and approval of railway monobloc wheel design.

Stage 3 bucket shank bypass holes and related method

DOEpatents

Leone, Sal Albert; Eldrid, Sacheverel Quentin; Lupe, Douglas Arthur

2002-01-01

In a multi-stage turbine wherein at least one turbine wheel supports a row of buckets for rotation, and wherein the turbine wheel is located axially between first and second annular fixed arrays of nozzles, a cooling air circuit for purging a wheelspace between the turbine wheel and the second fixed annular array of nozzles comprising a flowpath through a shank portion of one or more buckets connecting a wheelspace between the turbine wheel and the first fixed annular array of nozzles with the wheelspace between the turbine wheel and the second fixed annular array of nozzles.

Mars Pathfinder: The Wheel Abrasion Experiment

NASA Technical Reports Server (NTRS)

1996-01-01

NASA Lewis Research Center's Wheel Abrasion Experiment (WAE) will measure the amount of wear on wheel surfaces of the Mars Pathfinder rover. WAE uses thin films of Al, Ni, and Pt (ranging in thickness from 200 to 1000 angstroms) deposited on black, anodized Al strips attached to the rover wheel. As the wheel moves across the martian surface, changes in film reflectivity will be monitored by reflected sunlight. These changes, measured as output from a special photodetector mounted on the rover chassis, will be due to abrasion of the metal films by martian surface sand, dust, and clay.

METHOD FOR SOLDERING NORMALLY NON-SOLDERABLE ARTICLES

DOEpatents

McGuire, J.C.

1959-11-24

Methods are presented for coating and joining materials which are considered difficult to solder by utilizing an abrasive wheel and applying a bar of a suitable coating material, such as Wood's metal, to the rotating wheel to fill the cavities of the abrasive wheel and load the wheel with the coating material. The surface of the base material is then rubbed against the loaded rotating wheel, thereby coating the surface with the soft coating metal. The coating is a cohesive bonded layer and holds the base metal as tenaciously as a solder holds to easily solderable metals.

A predictive wheel-soil interaction model for planetary rovers validated in testbeds and against MER Mars rover performance data

NASA Astrophysics Data System (ADS)

Richter, L.; Ellery, A.; Gao, Y.; Michaud, S.; Schmitz, N.; Weiss, S.

Successful designs of vehicles intended for operations on planetary objects outside the Earth demand, just as for terrestrial off-the-road vehicles, a careful assessment of the terrain relevant for the vehicle mission and predictions of the mobility performance to allow rational trade-off's to be made for the choice of the locomotion concept and sizing. Principal issues driving the chassis design for rovers are the stress-strain properties of the planetary surface soil, the distribution of rocks in the terrain representing potential obstacles to movement, and the gravity level on the celestial object in question. Thus far, planetary rovers have been successfully designed and operated for missions to the Earth's moon and to the planet Mars, including NASA's Mars Exploration Rovers (MER's) `Spirit' and `Opportunity' being in operation on Mars since their landings in January 2004. Here we report on the development of a wheel-soil interaction model with application to wheel sizes and wheel loads relevant to current and near-term robotic planetary rovers, i.e. wheel diameters being between about 200 and 500 mm and vertical quasistatic wheel loads in operation of roughly 100 to 200 N. Such a model clearly is indispensable for sizings of future rovers to analyse the aspect of rover mobility concerned with motion across soils. This work is presently funded by the European Space Agency (ESA) as part of the `Rover Chassis Evaluation Tools' (RCET) effort which has developed a set of S/W-implemented models for predictive mobility analysis of rovers in terms of movement on soils and across obstacles, coupled with dedicated testbeds to validate the wheel-soil models. In this paper, we outline the details of the wheel-soil modelling performed within the RCET work and present comparisons of predictions of wheel performance (motion resistance, torque vs. slip and drawbar pull vs. slip) for specific test cases with the corresponding measurements performed in the RCET single wheel testbed and in the RCET system-level testbed, the latter permitting drawbar pull vs. slip measurements for complete rover development vehicles under controlled and homogeneous soil conditions. Required modifications of the wheel-soil model, in particular related to modelling the effect of wheel slip, are discussed. To strengthen the model validation base, we have run single wheel measurements using a spare MER Mars rover wheel and have performed comparisons with MER actual mobility performance data, available through one of us (LR) who is a member of the MER Athena science team. Corresponding results will be presented. Keywords: rovers, wheel, soil, mobility, vehicle performance, RCET (Rover Chassis Evaluation Tools), MER (Mars Exploration Rover mission) 2

Prediction of solvation enthalpy of gaseous organic compounds in propanol

NASA Astrophysics Data System (ADS)

Golmohammadi, Hassan; Dashtbozorgi, Zahra

2016-09-01

The purpose of this paper is to present a novel way for developing quantitative structure-property relationship (QSPR) models to predict the gas-to-propanol solvation enthalpy (Δ H solv) of 95 organic compounds. Different kinds of descriptors were calculated for each compound using the Dragon software package. The variable selection technique of replacement method (RM) was employed to select the optimal subset of solute descriptors. Our investigation reveals that the dependence of physical chemistry properties of solution on solvation enthalpy is nonlinear and that the RM method is unable to model the solvation enthalpy accurately. The results established that the calculated Δ H solv values by SVM were in good agreement with the experimental ones, and the performances of the SVM models were superior to those obtained by RM model.

A correct enthalpy relationship as thermal comfort index for livestock.

PubMed

Rodrigues, Valéria Cristina; da Silva, Iran José Oliveira; Vieira, Frederico Márcio Corrêa; Nascimento, Sheila Tavares

2011-05-01

Researchers working with thermal comfort have been using enthalpy to measure thermal energy inside rural facilities, establishing indicator values for many situations of thermal comfort and heat stress. This variable turned out to be helpful in analyzing thermal exchange in livestock systems. The animals are exposed to an environment which is decisive for the thermoregulatory process, and, consequently, the reactions reflect states of thermal comfort or heat stress, the last being responsable for problems of sanity, behavior and productivity. There are researchers using enthalpy as a qualitative indicator of thermal environment of livestock such as poultry, cattle and hogs in tropical regions. This preliminary work intends to check different enthalpy equations using information from classical thermodynamics, and proposes a direct equation as thermal comfort index for livestock systems.

Effects of intrinsic aerobic capacity and ovariectomy on voluntary wheel running and nucleus accumbens dopamine receptor gene expression

PubMed Central

Park, Young-Min; Kanaley, Jill A.; Padilla, Jaume; Zidon, Terese; Welly, Rebecca J.; Will, Matthew J.; Britton, Steven L.; Koch, Lauren G.; Ruegsegger, Gregory N.; Booth, Frank W.; Thyfault, John P.; Vieira-Potter, Victoria J.

2016-01-01

Rats selectively bred for high (HCR) and low (LCR) aerobic capacity show a stark divergence in wheel running behavior, which may be associated with dopamine (DA) system in the brain. HCR possess greater motivation for voluntary running along with greater brain DA activity compared to LCR. We recently demonstrated that HCR are not immune to ovariectomy (OVX)-associated reductions in spontaneous cage (i.e. locomotor) activity. Whether HCR and LCR rats differ in their OVX-mediated voluntary wheel running response is unknown. PURPOSE To determine whether HCR are protected from OVX-associated reduction in voluntary wheel running. METHODS Forty female HCR and LCR rats (age ~27 weeks) had either SHM or OVX operations, and given access to a running wheel for 11 weeks. Weekly wheel running distance was monitored throughout the intervention. Nucleus accumbens (NAc) was assessed for mRNA expression of DA receptors at sacrifice. RESULTS Compared to LCR, HCR ran greater distance and had greater ratio of excitatory/inhibitory DA mRNA expression (both line main effects, P<0.05). Wheel running distance was significantly, positively correlated with the ratio of excitatory/inhibitory DA mRNA expression across animals. In both lines, OVX reduced wheel running (P<0.05). Unexpectedly, although HCR started with significantly greater voluntary wheel running, they had greater OVX-induced reduction in wheel running than LCR such that no differences were found 11 weeks after OVX between HCROVX and LCROVX (interaction, P<0.05). This significant reduction in wheel running in HCR was associated with an OVX-mediated reduction in the ratio of excitatory/inhibitory DA mRNA expression. CONCLUSION DA system in the NAc region may play a significant role in motivation to run in female rats. Compared to LCR, HCR rats run significantly more, which associates with greater ratio of excitatory/inhibitory DA mRNA expression. However, despite greater inherent motivation to run and an associated brain DA mRNA expression profile, these HCR rats are not protected against OVX-induced reduction in wheel running. The impairment in wheel running in HCR rats may be partially explained by their reduced ratio of excitatory/inhibitory DA receptor mRNA expression. PMID:27297873

Articulated Suspension Without Springs

NASA Technical Reports Server (NTRS)

Bickler, Donald B.

1990-01-01

Wheels negotiate bumps and holes with minimal tilting of vehicle body. In new suspension, wheel climbs obstacle as high as 1 1/2 times its diameter without excessive tilting of chassis. Provides highly stable ride over rough ground for such vehicles as wheelchairs, military scout cars, and police and fire robots. System of levers distributes weight to wheels. Sized to distribute equal or other desired portions of load among wheels.

Robotic Two-Wheeled Vehicle

NASA Technical Reports Server (NTRS)

Edlund, Jeffrey E. (Inventor); Burdick, Joel (Inventor); Abad-Manterola, Pablo (Inventor); Matthews, Jaret B. (Inventor); Nesnas, Issa A. D. (Inventor)

2014-01-01

A robotic two-wheeled vehicle comprising a connection body interposed between the two wheels are described. A drum can be coaxially located in a central region of the connection body and can support a hollow arm projecting radially from the drum. A tether can be inserted in the arm and connected to a second drum. Instruments and sensors can be accommodated in a case housed inside each wheel.

Robotic Two-Wheeled Vehicle

NASA Technical Reports Server (NTRS)

Nesnas, Issa A. D. (Inventor); Matthews, Jaret B. (Inventor); Edlund, Jeffrey E. (Inventor); Burdick, Joel (Inventor); Abad-Manterola, Pablo (Inventor)

2013-01-01

A robotic two-wheeled vehicle comprising a connection body interposed between the two wheels are described. A drum can be coaxially located in a central region of the connection body and can support a hollow arm projecting radially from the drum. A tether can be inserted in the arm and connected to a second drum. Instruments and sensors can be accommodated in a case housed inside each wheel.

Effect of uphill and downhill walking on walking performance in geriatric patients using a wheeled walker.

PubMed

Lindemann, Ulrich; Schwenk, Michael; Schmitt, Syn; Weyrich, Michael; Schlicht, Wolfgang; Becker, Clemens

2017-08-01

Wheeled walkers are recommended to improve walking performance in older persons and to encourage and assist participation in daily life. Nevertheless, using a wheeled walker can cause serious problems in the natural environment. This study aimed to compare uphill and downhill walking with walking level in geriatric patients using a wheeled walker. Furthermore, we investigated the effect of using a wheeled walker with respect to dual tasking when walking level. A total of 20 geriatric patients (median age 84.5 years) walked 10 m at their habitual pace along a level surface, uphill and downhill, with and without a standard wheeled walker. Gait speed, stride length and cadence were assessed by wearable sensors and the walk ratio was calculated. When using a wheeled walker while walking level the walk ratio improved (0.58 m/[steps/min] versus 0.57 m/[steps/min], p = 0.023) but gait speed decreased (1.07 m/s versus 1.12 m/s, p = 0.020) when compared to not using a wheeled walker. With respect to the walk ratio, uphill and downhill walking with a wheeled walker decreased walking performance when compared to level walking (0.54 m/[steps/min] versus 0.58 m/[steps/min], p = 0.023 and 0.55 m/[steps/min] versus 0.58 m/[steps/min], p = 0.001, respectively). At the same time, gait speed decreased (0.079 m/s versus 1.07 m/s, p < 0.0001) or was unaffected. The use of a wheeled walker improved the quality of level walking but the performance of uphill and downhill walking was worse compared to walking level when using a wheeled walker.

Theory investigation progress of DMAZ

NASA Astrophysics Data System (ADS)

Xie, Hui; Mu, Xiaogang; Zhang, Yue; Wang, Xuanjun

2017-05-01

The recent progress in the theoretical study of N, N-dimethyl-2-azidoethylamine (DMAZ), a new type of azide fuel, is summarized. Thermodynamic Properties (such as Enthalpy-of-Formation, Enthalpy-of-Vaporization, and Enthalpy-of-Sublimation), conformers, Spectrums, the Henry's constant, ignition delay et al. are studied by Density Functional Theory (DFT). It is proved that DMAZ has good performance with a density impulse 2.499 Ns/m3, and has a good application prospect in replacing the traditional hydrazine propellant methyl-hydrazine (MMH).

Prediction of the vapor pressure and vaporization enthalpy of 1-n-alkyl-3-methylimidazolium-bis-(trifluoromethanesulfonyl) amide ionic liquids.

PubMed

Diedenhofen, Michael; Klamt, Andreas; Marsh, Kenneth; Schäfer, Ansgar

2007-09-07

The vapor pressures and vaporization enthalpies of a series of 1-n-alkyl-3-methylimidazolium-bis-(trifluoromethanesulfonyl) amide ionic liquids have been predicted with two different approaches using the COSMO-RS method and quantum chemical gas phase calculations. While the calculated enthalpies are in good agreement with the experimental data, COSMO-RS seems to underestimate the vapor pressures by roughly 0.5-4 log units dependent on the IL and approach used.

Wheel inspection system environment.

DOT National Transportation Integrated Search

2008-11-18

International Electronic Machines Corporation (IEM) has developed and is now marketing a state-of-the-art Wheel Inspection System Environment (WISE). WISE provides wheel profile and dimensional measurements, i.e. rim thickness, flange height, flange ...

Sustainable Rural Energy: Traditional Water Wheels in Padang (PWW) Indonesia

NASA Astrophysics Data System (ADS)

Ibrahim, Gusri Akhyar; Haron, Che Hassan Che; Azhari, Che Husna

2010-06-01

Renewable and sustainable energy is increasingly gaining interest in current research circles due to the debates on renewable energy resources. It is essential for scientists and researchers to search for solutions in renewable energy resources, with effective technologies, and low cost in operation and maintenance. Hydro resources can be considered a potential renewable energy resource. The traditional water wheel with simple construction coupled with a basic concept of technology can be utilised as a renewable and sustainable rural energy system. This paper discusses the case of the water wheel as a renewable energy system employed in Padang, Indonesia. The Padang water wheel is constructed from hardwood material with a diameter of 300 cm and width of 40 cm. It is built on a river using water flow to generate the movement of the wheel. The water wheel application in the area showed that it is suitable to be utilised to elevate and distribute water to rice fields located at a higher level than the water level of the river. The water wheel capacity is about 100-120 liters/min. It could continuously irrigate ±5 ha. of the rice fields. One of the advantages of this water wheel type is to function as a green technology concept promising no negative effect on the environment. The traditional water wheel has also a big economic impact on the rural economy, increasing the productivity of the rice fields. The people of Padang live in a water landscape encompassing the water wheel as an ubiquitous part of their lives, hence they relate to it and the technology of fabrication as well as the utilisation, making it an amenable and effective technology, finding relevance in the modern world.

Four-wheeled walker related injuries in older adults in the Netherlands.

PubMed

van Riel, K M M; Hartholt, K A; Panneman, M J M; Patka, P; van Beeck, E F; van der Cammen, T J M

2014-02-01

With ageing populations worldwide, mobility devices are used more than ever. In the current literature there is no consensus whether the available mobility devices safely improve the mobility of their users. Also, evidence is lacking concerning the risks and types of injuries sustained while using a four-wheeled walker. To assess injury risks and injury patterns in older adults (≥65 years) who presented at Emergency Departments (ED) in the Netherlands with an injury due to using a four-wheeled walker. In this study, the Dutch Injury Surveillance System was used to obtain a national representative sample of annual ED visits in the Netherlands in the adult population (≥65 years) sustaining an injury while using a four-wheeled walker. The numbers of four-wheeled walker users in the Netherlands were obtained from the national insurance board. The numbers of ED visits were divided by the numbers of four-wheeled walker users to calculate age- and sex-specific injury risks. Annually 1869 older adults visited an ED after sustaining an injury while using a four-wheeled walker. Falls were the main cause of injury (96%). The injury risk was 3.1 per 100 users of four-wheeled walkers. Women (3.5 per 100 users) had a higher risk than men (2.0 per 100 users). Injury risk was the highest in women aged 85 years and older (6.2 per 100 users). The majority of injuries were fractures (60%) with hip fracture (25%) being the most common injury. Nearly half of all four-wheeled walker related injuries required hospitalisation, mostly due to hip fractures. Healthcare costs per injury were approximately €12 000. This study presents evidence that older adults experiencing a fall while using a four-wheeled walker are at high risk to suffer severe injuries.

Estimators of wheel slip for electric vehicles using torque and encoder measurements

NASA Astrophysics Data System (ADS)

Boisvert, M.; Micheau, P.

2016-08-01

For the purpose of regenerative braking control in hybrid and electrical vehicles, recent studies have suggested controlling the slip ratio of the electric-powered wheel. A slip tracking controller requires an accurate slip estimation in the overall range of the slip ratio (from 0 to 1), contrary to the conventional slip limiter (ABS) which calls for an accurate slip estimation in the critical slip area, estimated at around 0.15 in several applications. Considering that it is not possible to directly measure the slip ratio of a wheel, the problem is to estimate the latter from available online data. To estimate the slip of a wheel, both wheel speed and vehicle speed must be known. Several studies provide algorithms that allow obtaining a good estimation of vehicle speed. On the other hand, there is no proposed algorithm for the conditioning of the wheel speed measurement. Indeed, the noise included in the wheel speed measurement reduces the accuracy of the slip estimation, a disturbance increasingly significant at low speed and low torque. Herein, two different extended Kalman observers of slip ratio were developed. The first calculates the slip ratio with data provided by an observer of vehicle speed and of propeller wheel speed. The second observer uses an original nonlinear model of the slip ratio as a function of the electric motor. A sinus tracking algorithm is included in the two observers, in order to reject harmonic disturbances of wheel speed measurement. Moreover, mass and road uncertainties can be compensated with a coefficient adapted online by an RLS. The algorithms were implemented and tested with a three-wheel recreational hybrid vehicle. Experimental results show the efficiency of both methods.

Interaction between a railway track and uniformly moving tandem wheels

NASA Astrophysics Data System (ADS)

Belotserkovskiy, P. M.

2006-12-01

Interaction among loaded wheels via railway track is studied. The vertical parametric oscillations of an infinite row of identical equally spaced wheels, bearing constant load and uniformly moving over a railway track, are calculated by means of Fourier series technique. If the distance between two consecutive wheels is big enough, then one can disregard their interaction via the railway track and consider every wheel as a single one. In this case, however, the Fourier series technique represents an appropriate computation time-saving approximation to a Fourier integral transformation technique that describes the oscillations of a single moving wheel. Two schemes are considered. In the first scheme, every wheel bears the same load. In the second one, consecutive wheels bear contrarily directed loads of the same magnitude. The second scheme leads to simpler calculations and so is recommended to model the wheel-track interaction. The railway track periodicity due to sleeper spacing is taken into account. Each period is the track segment between two adjacent sleepers. A partial differential equation with constant coefficients governs the vertical oscillations of each segment. Boundary conditions bind the oscillations of two neighbour segments and provide periodicity to the track. The shear deformation in the rail cross-section strongly influences the parametric oscillations. It also causes discontinuity of the rail centre-line slope at any point, where a concentrated transverse force is applied. Therefore, Timoshenko beam properties with respect to the topic of this paper are discussed. Interaction between a railway track and a bogie moving at moderate speed is studied. The study points to influence of the bogie frame oscillations on variation in the wheel-rail contact force over the sleeper span. The simplified bogie model considered includes only the primary suspension. A static load applied to the bogie frame centre presents the vehicle body.

Inflight Performance of Cassini Reaction Wheel Bearing Drag in 1997-2013

NASA Technical Reports Server (NTRS)

Lee, Allan Y.; Wang, Eric K.

2013-01-01

As the first spacecraft to achieve orbit at Saturn in 2004, Cassini has collected science data throughout its four-year prime mission (2004-08), and has since been approved for a first and second extended missions through September 2017. Cassini is a three-axis stabilized spacecraft. It uses reaction wheels to achieve high level of spacecraft pointing stability that is needed during imaging operations of several science instruments. The Cassini flight software makes in-flight estimates of reaction wheel bearing drag torque and made them available to the mission operations team. These telemetry data are being trended for the purpose of monitoring the long-term health of the reaction wheel bearings. Anomalous drag torque signatures observed over the past 15 years are described in this paper. One of these anomalous drag conditions is bearing cage instability that appeared (and disappeared) spontaneously and unpredictably. Cage instability is an uncontrolled vibratory motion of the bearing cage that can produce high-impact forces internal to the bearing that will cause intermittent and erratic torque transients. Characteristics of the observed cage instabilities and other drag torque "spikes" are described in this paper. In day-to-day operations, the reaction wheels' rates must be neither too high nor too low. To protect against operating the wheels in any undesirable conditions (such as prolonged low spin rate operations), a ground software tool named Reaction Wheel Bias Optimization Tool (RBOT) was developed for the management of the wheels. Disciplined and long-term use of this ground software has led to significant reduction in the daily consumption rate of the wheels' low spin rate dwell time. Flight experience on the use of this ground software tool as well as other lessons learned on the management of Cassini reaction wheels is given in this paper.

Modeling of the motion of automobile elastic wheel in real-time for creation of wheeled vehicles motion control electronic systems

NASA Astrophysics Data System (ADS)

Balakina, E. V.; Zotov, N. M.; Fedin, A. P.

2018-02-01

Modeling of the motion of the elastic wheel of the vehicle in real-time is used in the tasks of constructing different models in the creation of wheeled vehicles motion control electronic systems, in the creation of automobile stand-simulators etc. The accuracy and the reliability of simulation of the parameters of the wheel motion in real-time when rolling with a slip within the given road conditions are determined not only by the choice of the model, but also by the inaccuracy and instability of the numerical calculation. It is established that the inaccuracy and instability of the calculation depend on the size of the step of integration and the numerical method being used. The analysis of these inaccuracy and instability when wheel rolling with a slip was made and recommendations for reducing them were developed. It is established that the total allowable range of steps of integration is 0.001.0.005 s; the strongest instability is manifested in the calculation of the angular and linear accelerations of the wheel; the weakest instability is manifested in the calculation of the translational velocity of the wheel and moving of the center of the wheel; the instability is less at large values of slip angle and on more slippery surfaces. A new method of the average acceleration is suggested, which allows to significantly reduce (up to 100%) the manifesting of instability of the solution in the calculation of all parameters of motion of the elastic wheel for different braking conditions and for the entire range of steps of integration. The results of research can be applied to the selection of control algorithms in vehicles motion control electronic systems and in the testing stand-simulators

High-runner mice have reduced incentive salience for a sweet-taste reward when housed with wheel access.

PubMed

Thompson, Zoe; Kolb, Erik M; Garland, Theodore

2018-01-01

To explore reward substitution in the context of voluntary exercise, female mice from four replicate high-runner (HR) lines (bred for wheel running) and four non-selected control (C) lines were given simultaneous access to wheels and palatable solutions as competing rewards (two doses of saccharin [0.1, 0.2% w/v]; two doses of common artificial sweetener blends containing saccharin [Sweet 'N Low ® : 0.1, 0.2% w/v], aspartame [Equal ® : 0.04, 0.08% w/v], or sucralose [Splenda ® : 0.08, 0.16% w/v]; or two doses of sucrose [3.5, 10.5% w/v]). Wheel running and fluid consumption were measured daily, with each dose (including plain water) lasting two days and two "washout" days between solutions. In a separate set of mice, the experiment was repeated without wheel access. The artificial sweeteners had no statistical effect on wheel running. However, based on proportional responses, both doses of sucrose significantly elevated wheel running in C but not HR mice. In contrast, the high dose of sucrose suppressed home-cage activity for both linetypes. Both sucrose and the artificial blends generally increased fluid consumption in a dose-dependent manner. When they had access to wheels, HR had a significantly smaller increase in consumption of artificial sweetener blends when compared with C mice, but not when housed without wheels. Overall, these results provide further evidence that the reward system of HR mice has evolved, and specifically suggest that HR mice have a reduced incentive salience for some artificial sweetener blends, likely attributable to the stronger competing reward of wheel running that has evolved in these lines. Copyright © 2017 Elsevier B.V. All rights reserved.

Energetic basis on interactions between ferredoxin and ferredoxin NADP{sup +} reductase at varying physiological conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kinoshita, Misaki; Kim, Ju Yaen; Kume, Satoshi

In spite of a number of studies to characterize ferredoxin (Fd):ferredoxin NADP{sup +} reductase (FNR) interactions at limited conditions, detailed energetic investigation on how these proteins interact under near physiological conditions and its linkage to FNR activity are still lacking. We herein performed systematic Fd:FNR binding thermodynamics using isothermal titration calorimetry (ITC) at distinct pH (6.0 and 8.0), NaCl concentrations (0–200 mM), and temperatures (19–28 °C) for mimicking physiological conditions in chloroplasts. Energetically unfavorable endothermic enthalpy changes were accompanied by Fd:FNR complexation at all conditions. This energetic cost was compensated by favorable entropy changes, balanced by conformational and hydrational entropy. Increases inmore » the NaCl concentration and pH weakened interprotein affinity due to the less contribution of favorable entropy change regardless of energetic gains from enthalpy changes, suggesting that entropy drove complexation and modulated affinity. Effects of temperature on binding thermodynamics were much smaller than those of pH and NaCl. NaCl concentration and pH-dependent enthalpy and heat capacity changes provided clues for distinct binding modes. Moreover, decreases in the enthalpy level in the Hammond's postulate-based energy landscape implicated kinetic advantages for FNR activity. All these energetic interplays were comprehensively demonstrated by the driving force plot with the enthalpy-entropy compensation which may serve as an energetic buffer against outer stresses. We propose that high affinity at pH 6.0 may be beneficial for protection from proteolysis of Fd and FNR in rest states, and moderate affinity at pH 8.0 and proper NaCl concentrations with smaller endothermic enthalpy changes may contribute to increase FNR activity. - Highlights: • Energetics of Fd:FNR binding were examined by considering physiological conditions. • NaCl and pH affect energetically Fd:FNR binding with minimal effects of temperature. • Enthalpy and heat capacity may modulate binding kinetics and modes for FNR activity. • Entropy drives complexation by overcoming unfavorable enthalpy and tunes affinity. • Driving force plot reveals condition-dependent energetic interplays for complexation.« less

High Enthalpy Effects on Two Boundary Layer Disturbances in Supersonic and Hypersonic Flow

NASA Astrophysics Data System (ADS)

Wagnild, Ross Martin

The fluid flow phenomenon of boundary layer transition is a complicated and difficult process to model and predict. The importance of the state of the boundary layer with regard to vehicle design cannot be understated. The high enthalpy environment in which high speed vehicles operate in further complicates the transition process by adding several more degrees of freedom. In this environment, the internal properties of the gas can stabilize or destabilize the boundary layer as well as modify the disturbances that cause transition. In the current work, the interaction of two types of disturbances with the high enthalpy flow environment are analyzed. The first is known as a second mode disturbance, which is acoustic in nature. The second type is known as a transient growth disturbance and is associated with flows behind roughness elements. Theoretical analyses, linear stability analyses, and computation fluid dynamics (CFD) are used to determine the ways in which these disturbances interact with the high enthalpy environment as well as the consequences of these interactions. First, acoustic wave are directly studied in order to gain a basic understanding of the response of second mode disturbances in the high enthalpy boundary layer. Next, this understanding is used in interpreting the results of several computations attempting to simulate the flow through a high enthalpy flow facility as well as experiments attempting to take advantage of the acoustic interaction with the high enthalpy environment. Because of the difficulty in modeling these experiments, direct simulations of acoustic waves in a hypersonic flow of a gas with molecular vibration are performed. Lastly, compressible transient growth disturbances are simulated using a linear optimal disturbance solver as well as a CFD solver. The effect of an internal molecular process on this type of disturbance is tested through the use of a vibrational mode. It is the goal of the current work to reinforce the critical importance of accurately capturing the physics of the "real" gas effects in the high enthalpy flow environment in order to understand and predict transition on high speed vehicles.

Stress Measurements in Railroad Wheels Via the Barkhausen Effect

DOT National Transportation Integrated Search

1977-02-01

The feasibility of utilizing the Barkhausen Effect in ferromagnetic steels as a nondestructive means for ascertaining residual stresses in railroad wheels was investigated. Railroad wheels are generally manufactured with compressive stress distributi...

Multi-component lightweight gearwheels with deep-drawn wheel body for automotive applications

NASA Astrophysics Data System (ADS)

Benkert, Tim; Hiller, Maria; Volk, Wolfram

2017-09-01

Multi-component gearwheels offer great lightweight opportunities for automotive applications. An assembly of a gear ring and a wheel body joined by press fit replaces the monolithic gearwheel. To save weight, the wheel body uses lightweight design. This lightweight design influences the assembled gearwheel’s mechanical properties like stiffness, weight and torque capacity. Further, the wheel body material influences the mentioned properties as well. In this paper, the effects of the lightweight wheel body manufactured by deep-drawing on the mechanical properties of the assembled gearwheel are investigated. Three different wheel body designs are examined regarding their stiffness and weight compared to a reference gearwheel. Using the best design, the influence of five materials with increasing yield strength on the maximum torque the gearwheel can transmit is studied. All research is done virtually using Abaqus 6.12-3.

Free vibration analysis of composite railway wheels

NASA Astrophysics Data System (ADS)

Ganesan, N.; Ramesh, T. C.

1992-02-01

Composite materials have been finding increasing applications in the field of transportation. A U.S.A. patent suggesting the use of composite materials for railway wheels is the basis for this paper. In thispaper, the natural vibrations of railway wheels made of composite materials have been theoretically estimated by the finite element method and compared with those in wheels made of steel. A thick conical shell element with displacements in the axial, radial and circumferential directions has been used in the analysis. This element brings out the coupling between the different modes of vibration, and this aspect is important in the dynamic analysis of composite wheels. Three geometries of wheels and two materials (Kevlar-epoxy and graphite-epoxy) have been used in the study. For each of these materials, two fiber orientations (radial and circumferential) have been taken up and their natural frequencies determined.

Improved infrared-sensing running wheel systems with an effective exercise activity indicator.

PubMed

Chen, Chi-Chun; Chang, Ming-Wen; Chang, Ching-Ping; Chang, Wen-Ying; Chang, Shin-Chieh; Lin, Mao-Tsun; Yang, Chin-Lung

2015-01-01

This paper describes an infrared-sensing running wheel (ISRW) system for the quantitative measurement of effective exercise activity in rats. The ISRW system provides superior exercise training compared with commercially available traditional animal running platforms. Four infrared (IR) light-emitting diode/detector pairs embedded around the rim of the wheel detect the rat's real-time position; the acrylic wheel has a diameter of 55 cm and a thickness of 15 cm, that is, it is larger and thicker than traditional exercise wheels, and it is equipped with a rubber track. The acrylic wheel hangs virtually frictionless, and a DC motor with an axially mounted rubber wheel, which has a diameter of 10 cm, drives the acrylic wheel from the outer edge. The system can automatically train rats to run persistently. The proposed system can determine effective exercise activity (EEA), with the IR sensors (which are connected to a conventional PC) recording the rat exercise behavior. A prototype of the system was verified by a hospital research group performing ischemic stroke experiments on rats by considering middle cerebral artery occlusion. The experimental data demonstrated that the proposed system provides greater neuroprotection in an animal stroke model compared with a conventional treadmill and a motorized running wheel for a given exercise intensity. The quantitative exercise effectiveness indicator showed a 92% correlation between an increase in the EEA and a decrease in the infarct volume. This indicator can be used as a noninvasive and objective reference in clinical animal exercise experiments.

Experimental investigation into the mechanism of the polygonal wear of electric locomotive wheels

NASA Astrophysics Data System (ADS)

Tao, Gongquan; Wang, Linfeng; Wen, Zefeng; Guan, Qinghua; Jin, Xuesong

2018-06-01

Experiments were conducted at field sites to investigate the mechanism of the polygonal wear of electric locomotive wheels. The polygonal wear rule of electric locomotive wheels was obtained. Moreover, two on-track tests have been carried out to investigate the vibration characteristics of the electric locomotive's key components. The measurement results of wheels out-of-round show that most electric locomotive wheels exhibit polygonal wear. The main centre wavelength in the 1/3 octave bands is 200 mm and/or 160 mm. The test results of vibration characteristics indicate that the dominating frequency of the vertical acceleration measured on the axle box is approximately equal to the passing frequency of a polygonal wheel, and does not vary with the locomotive speed during the acceleration course. The wheelset modal analysis using the finite element method (FEM) indicates that the first bending resonant frequency of the wheelset is quite close to the main vibration frequency of the axle box. The FEM results are verified by the experimental modal analysis of the wheelset. Moreover, different plans were designed to verify whether the braking system and the locomotive's adhesion control have significant influence on the wheel polygon or not. The test results indicate that they are not responsible for the initiation of the wheel polygon. The first bending resonance of the wheelset is easy to be excited in the locomotive operation and it is the root cause of wheel polygon with centre wavelength of 200 mm in the 1/3 octave bands.

Uptake of wheel-filtration among clients of a supervised injecting facility: Can structured education work?

PubMed

Steele, Maureen; Silins, Edmund; Flaherty, Ian; Hiley, Sarah; van Breda, Nick; Jauncey, Marianne

2018-01-01

Wheel-filtration of pharmaceutical opioid tablets is a recognised harm reduction strategy, but uptake of the practice among people who inject drugs is low. The study aimed to: (i) examine perceptions of filtration practices; (ii) provide structured education on wheel-filtration; and (iii) assess uptake of the practice. Frequent opioid tablet injectors (n = 30) attending a supervised injecting facility in Sydney, Australia, received hands-on instruction on wheel-filtration based on recommended practice. Pre-education, post-education and follow-up questionnaires were administered. Wheel-filtration was generally regarded as better than cotton-filtration (the typical method) in terms of perceived effects on health, ease of use and overall drug effect. Sixty-eight percent of those who said they would try wheel-filtration after the education had actually done so. Of those who usually used cotton-filtration, over half (60%) had used wheel-filtration two weeks later. Uptake of safer preparation methods for pharmaceutical opioid tablets increases after structured education in wheel-filtration. Findings suggest that SIFs are an effective site for this kind of education. Supervised injecting facility workers are uniquely positioned to provide harm reduction education at the time of injection. [Steele M, Silins E, Flaherty I, Hiley S, van Breda N, Jauncey M. Uptake of wheel-filtration among clients of a supervised injecting facility: Can structured education work? Drug Alcohol Rev 2018;37:116-120]. © 2017 Australasian Professional Society on Alcohol and other Drugs.

A single administration of methamphetamine to mice early in the light period decreases running wheel activity observed during the dark period

PubMed Central

Kitanaka, Nobue; Kitanaka, Junichi; Hall, F. Scott; Uhl, George R.; Watabe, Kaname; Kubo, Hitoshi; Takahashi, Hitoshi; Tatsuta, Tomohiro; Morita, Yoshio; Takemura, Motohiko

2014-01-01

Repeated intermittent administration of amphetamines acutely increases appetitive and consummatory aspects of motivated behaviors as well as general activity and exploratory behavior, including voluntary running wheel activity. Subsequently, if the drug is withdrawn, the frequency of these behaviors decrease, which is thought to be indicative of dysphoric symptoms associated with amphetamine withdrawal. Such decreases may be observed after chronic treatment or even after single drug administrations. In the present study, the effect of acute methamphetamine (METH) on running wheel activity, horizontal locomotion, appetitive behavior (food access), and consummatory behavior (food and water intake) was investigated in mice. A multi-configuration behavior apparatus designed to monitor the five behaviors was developed, where combined measures were recorded simultaneously. In the first experiment, naïve male ICR mice showed gradually increasing running wheel activity over three consecutive days after exposure to a running wheel, while mice without a running wheel showed gradually decreasing horizontal locomotion, consistent with running wheel activity being a positively motivated form of natural motor activity. In experiment 2, increased horizontal locomotion and food access, and decreased food intake, were observed for the initial 3 h after acute METH challenge. Subsequently, during the dark phase period decreased running wheel activity and horizontal locomotion were observed. The reductions in running wheel activity and horizontal locomotion may be indicative of reduced dopaminergic function, although it remains to be seen if these changes may be more pronounced after more prolonged METH treatments. PMID:22079320

The effect of environmental factors on morphine withdrawal in C57BL/6J mice: running wheel access and group housing.

PubMed

Balter, Rebecca E; Dykstra, Linda A

2012-11-01

There is evidence to suggest that the rewarding effects of drugs of abuse can be altered by environmental manipulations such as housing conditions and access to running wheels. There is less information about how these environmental manipulations alter withdrawal behaviors following the termination of chronic drug administration. The objective of this study is to examine the effects of access to running wheels and group housing on spontaneous morphine withdrawal. C57BL/6J mice were assigned to one of the three housing conditions: wheel access (singly housed), no wheels (singly housed), or group-housed (no wheels). Mice received 30 or 56 mg/kg morphine or saline (s.c.) twice daily for 5.5 days. At baseline and at 8, 24, 32, and 48 h following the final injection, latency to respond on a hot plate was determined across a range of temperatures (50, 52, 54, and 56 °C). Latency to respond decreased as a function of temperature. Response latencies during the withdrawal period were decreased in mice without wheel access treated with both 30 and 56 mg/kg of morphine. This increase in thermal sensitivity was significantly attenuated in singly housed mice with wheel access and in group-housed mice; however, the effects were less pronounced in the group-housed mice and depended upon the time during withdrawal. Both wheel access and group housing attenuate the increase in thermal sensitivity seen in morphine-treated mice during morphine withdrawal.

Increasing Slew Performance of Reaction Wheel Attitude Control Systems

DTIC Science & Technology

2013-09-01

vectors in any arbitrary direction creates the momentum envelope (Chapter IV). The shape of the reaction wheel momentum envelope is a polyhedron [15...performance. This procedural limitation further reduces the operable reaction wheel momentum space polyhedron to the largest inscribed sphere, which...respective plane. These minima are also the global minima, each marked in magenta. The four-wheel polyhedron is again shown in three orthogonal views in

Wheel Diameter and Speedometer Reading

NASA Astrophysics Data System (ADS)

Murray, Clifton

2010-09-01

Most introductory physics students have seen vehicles with nonstandard wheel diameters; some may themselves drive "low-rider" cars or "big-wheel" pickup trucks. But how does changing wheel diameter affect speedometer readout for a given speed? Deriving the answer can be followed readily by students who have been introduced to rotation, and it makes a good illustration of how reasoning in physics can lead to a result that is useful outside the classroom.

Suspension Parameter Measurements of Wheeled Military Vehicles

DTIC Science & Technology

2012-08-01

suspension through the wheel pads. The SPIdER was designed so that in the future, with a modest amount of modification , it can be upgraded to include the...AND MOBILITY (P&M) MINI-SYMPOSIUM AUGUST 14-16, MICHIGAN SUSPENSION PARAMETER MEASUREMENTS OF WHEELED MILITARY VEHICLES Dale Andreatta Gary...was built to measure the suspension parameters of any military wheeled vehicle. This is part of an ongoing effort to model and predict vehicle

Light and Heavy Tactical Wheeled Vehicle Fuel Consumption Evaluations Using Fuel Efficient Gear Oils (FEGO)

DTIC Science & Technology

2016-05-01

UNCLASSIFIED LIGHT AND HEAVY TACTICAL WHEELED VEHICLE FUEL CONSUMPTION EVALUATIONS USING FUEL EFFICIENT GEAR OILS (FEGO) FINAL... HEAVY TACTICAL WHEELED VEHICLE FUEL CONSUMPTION EVALUATIONS USING FUEL EFFICIENT GEAR OILS (FEGO) FINAL REPORT TFLRF No. 477 by Adam C...August 2014 – March 2016 4. TITLE AND SUBTITLE LIGHT AND HEAVY TACTICAL WHEELED VEHICLE FUEL CONSUMPTION EVALUATIONS USING FEUL EFFICIENT GEAR OILS

New Integrated Testing System for the Validation of Vehicle-Snow Interaction Models

DTIC Science & Technology

2010-08-06

are individual wheel speeds, accelerator pedal position, vehicle speed, yaw rate, lateral acceleration, steering wheel angle and brake ...forces and moments at each wheel center, vehicle body slip angle , speed, acceleration, yaw rate, roll, and pitch. The profilometer has a 3-D scanning...Stability Program. The test vehicle provides measurements that include three forces and moments at each wheel center, vehicle body slip angle , speed

Pre-exposure to wheel running disrupts taste aversion conditioning.

PubMed

Salvy, Sarah-Jeanne; Pierce, W David; Heth, Donald C; Russell, James C

2002-05-01

When rats are given access to a running wheel after drinking a flavored solution, they subsequently drink less of that flavor solution. It has been suggested that running produces a conditioned taste aversion (CTA). This study explored whether CTA is eliminated by prior exposure to wheel running [i.e., unconditioned stimulus (UCS) pre-exposure effect]. The rats in the experimental group (UW) were allowed to wheel run for 1 h daily for seven consecutive days of pre-exposure. Rats in the two other groups had either access to locked wheels (LW group) or were maintained in their home cages (HC group) during the pre-exposure days. All rats were then exposed to four paired and four unpaired trials using a "ABBAABBA" design. Conditioning trials were composed of one flavored liquid followed by 60-min access to wheel running. For the unpaired trials, rats received a different flavor not followed by the opportunity to run. All rats were then initially tested for water consumption followed by tests of the two flavors (paired or unpaired) in a counterbalanced design. Rats in the UW group show no CTA to the liquid paired with wheel running, whereas LW and HC groups developed CTA. These results indicate that pre-exposure to wheel running (i.e., the UCS), eliminates subsequent CTA.

Omni-directional and holonomic rolling platform with decoupled rotational and translational degrees of freedom

DOEpatents

Pin, F.G.; Killough, S.M.

1994-12-20

A wheel assembly includes a support, a cage rotatably mounted on the support and having a longitudinal rotation axis, a first ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis of the cage, and a second ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis or the cage and to the rotation axis of the first ball wheel. A control circuit includes a photodetector signal which indicates ground contact for each ball wheel, and a tachometer which indicates actual drive shaft velocity. 6 figures.

Wheel running decreases the positive reinforcing effects of heroin.

PubMed

Smith, Mark A; Pitts, Elizabeth G

2012-01-01

The purpose of this study was to examine the effects of voluntary wheel running on the positive reinforcing effects of heroin in rats with an established history of drug self-administration. Rats were assigned to sedentary (no wheel) and exercise (wheel) conditions and trained to self-administer cocaine under positive reinforcement contingencies. Rats acquiring cocaine self-administration were then tested with various doses of heroin during daily test sessions. Sedentary rats self-administered more heroin than exercising rats, and this effect was greatest at low and moderate doses of heroin. These data suggest that voluntary wheel running decreases the positive reinforcing effects of heroin.

Omnidirectional wheel

NASA Technical Reports Server (NTRS)

Blumrich, J. F. (Inventor)

1974-01-01

The apparatus consists of a wheel having a hub with radially disposed spokes which are provided with a plurality of circumferential rim segments. These rim segments carry, between the spokes, rim elements which are rigid relative to their outer support surfaces, and defined in their outer contour to form a part of the circle forming the wheel diameter. The rim segments have provided for each of the rim elements an independent drive means selectively operable when the element is in ground contact to rotatably drive the rim element in a direction of movement perpendicularly lateral to the normal plane of rotation and movement of the wheel. This affords the wheel omnidirectional movement.

Magnetically suspended reaction wheel assembly

NASA Technical Reports Server (NTRS)

Stocking, G.

1984-01-01

The magnetically suspended reaction wheel assembly (MSRWA) is the product of a development effort funded by the Air Force Materials Laboratory (AFML) at Wright Patterson AFB. The specific objective of the project was to establish the manufacturing processes for samarium cobalt magnets and demonstrate their use in a space application. The development was successful on both counts. The application portion of the program, which involves the magnetically suspended reaction wheel assembly, is emphasized. The requirements for the reaction wheel were based on the bias wheel requirements of the DSP satellite. The tasks included the design, fabrication, and test of the unit to the DSP program qualification requirements.

Magnetically suspended reaction wheel assembly

NASA Astrophysics Data System (ADS)

Stocking, G.

1984-11-01

The magnetically suspended reaction wheel assembly (MSRWA) is the product of a development effort funded by the Air Force Materials Laboratory (AFML) at Wright Patterson AFB. The specific objective of the project was to establish the manufacturing processes for samarium cobalt magnets and demonstrate their use in a space application. The development was successful on both counts. The application portion of the program, which involves the magnetically suspended reaction wheel assembly, is emphasized. The requirements for the reaction wheel were based on the bias wheel requirements of the DSP satellite. The tasks included the design, fabrication, and test of the unit to the DSP program qualification requirements.

Wind wheel electric power generator

NASA Technical Reports Server (NTRS)

Kaufman, J. W. (Inventor)

1980-01-01

Wind wheel electric power generator apparatus includes a housing rotatably mounted upon a vertical support column. Primary and auxiliary funnel-type, venturi ducts are fixed onto the housing for capturing wind currents and conducting to a bladed wheel adapted to be operatively connected with the generator apparatus. Additional air flows are also conducted onto the bladed wheel; all of the air flows positively effecting rotation of the wheel in a cumulative manner. The auxiliary ducts are disposed at an acute angle with respect to the longitudinal axis of the housing, and this feature, together with the rotatability of the housing and the ducts, permits capture of wind currents within a variable directional range.

Omni-directional and holonomic rolling platform with decoupled rotational and translational degrees of freedom

DOEpatents

Pin, Francois G.; Killough, Stephen M.

1994-01-01

A wheel assembly includes a support, a cage rotatably mounted on the support and having a longitudinal rotation axis, a first ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis of the cage, and a second ball wheel rotatably mounted in the cage and having a rotation axis orthogonal to the rotation axis or the cage and to the rotation axis of the first ball wheel. A control circuit includes a photodetector signal which indicates ground contact for each ball wheel, and a tachometer which indicates actual drive shaft velocity.

14 CFR 23.511 - Ground load; unsymmetrical loads on multiple-wheel units.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER... distribution, to the dual wheels and tires in each dual wheel landing gear unit. (c) Deflated tire loads. For...

Fracture Resistance of Railroad Wheels

DOT National Transportation Integrated Search

1974-09-01

The effects of manufacturing method, chemical composition, heat treatment, temperature, and loading rate on the plane strain fracture toughness KIC of railroad wheels have been determined. Carbon content of the wheels is shown to be the principal fac...

9. Close view of gate valves (foreground), paddle wheel guard ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Close view of gate valves (foreground), paddle wheel guard (midground), and water wheel (background), facing southeast (downstream) from drum screen cover. - Congdon Canal, Fish Screen, Naches River, Yakima, Yakima County, WA

Tire-rim interface pressure of a commercial vehicle wheel under radial loads: theory and experiment

NASA Astrophysics Data System (ADS)

Wan, Xiaofei; Shan, Yingchun; Liu, Xiandong; He, Tian; Wang, Jiegong

2017-11-01

The simulation of the radial fatigue test of a wheel has been a necessary tool to improve the design of the wheel and calculate its fatigue life. The simulation model, including the strong nonlinearity of the tire structure and material, may produce accurate results, but often leads to a divergence in calculation. Thus, a simplified simulation model in which the complicated tire model is replaced with a tire-wheel contact pressure model is used extensively in the industry. In this paper, a simplified tire-rim interface pressure model of a wheel under a radial load is established, and the pressure of the wheel under different radial loads is tested. The tire-rim contact behavior affected by the radial load is studied and analyzed according to the test result, and the tire-rim interface pressure extracted from the test result is used to evaluate the simplified pressure model and the traditional cosine function model. The results show that the proposed model may provide a more accurate prediction of the wheel radial fatigue life than the traditional cosine function model.

Articulated suspension system

NASA Technical Reports Server (NTRS)

Bickler, Donald B. (Inventor)

1989-01-01

The invention provides a rough terrain vehicle which maintains a substantially constant weight, and therefore traction, on all wheels, despite one wheel moving considerably higher or lower than the others, while avoiding a very soft spring suspension. The vehicle includes a chassis or body to be supported and a pair of side suspensions at either side of the body. In a six wheel vehicle, each side suspension includes a middle wheel, and front and rear linkages respectively coupling the front and rear wheels to the middle wheel. A body link pivotally connects the front and rear linkages together, with the middle of the body link rising or falling by only a fraction of the rise or fall of any of the three wheels. The body link pivotally supports the middle of the length of the body. A transverse suspension for suspending the end of the body on the side suspensions includes a middle part pivotally connected to the body about a longitudinal axis and opposite ends each pivotally connected to one of the side suspensions along at least a longitudinal axis.

Wheel running, voluntary ethanol consumption, and hedonic substitution.

PubMed

Ozburn, Angela Renee; Harris, R Adron; Blednov, Yuri A

2008-08-01

Few studies have examined the relationship between naturally rewarding behaviors and ethanol drinking behaviors in mice. Although natural and drug reinforcers activate similar brain circuitry, there is behavioral evidence suggesting food and drug rewards differ in perceived value. The primary goal of the present study was to investigate the relationships between naturally reinforcing stimuli and consumption of ethanol in ethanol preferring C57BL/6J mice. Mouse behaviors were observed after the following environmental manipulations: standard or enhanced environment, accessible or inaccessible wheel, and presence or absence of ethanol. Using a high-resolution volumetric drinking monitor and wheel running monitor, we evaluated whether alternating access to wheel running modified ethanol-related behaviors and whether alternating access to ethanol modified wheel running or subsequent ethanol-related behaviors. We found that ethanol consumption remains stable with alternating periods of wheel running. Wheel running increases in the absence of ethanol and decreases upon reintroduction of ethanol. Upon reintroduction of ethanol, an alcohol deprivation effect was seen. Collectively, the results support theories of hedonic substitution and suggest that female C57BL/6J mice express ethanol seeking and craving under these specific conditions.

First-Principles Study of Electronic Structure and Hydrogen Adsorption of 3d Transition Metal Exposed Paddle Wheel Frameworks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bak, J. H.; Le, V. D.; Kang, J.

2012-04-05

Open-site paddle wheels, comprised of two transition metals bridged with four carboxylate ions, have been widely used for constructing metal-organic frameworks with large surface area and high binding energy sites. Using first-principles density functional theory calculations, we have investigated atomic and electronic structures of various 3d transition metal paddle wheels before and after metal exposure and their hydrogen adsorption properties at open metal sites. Notably, the hydrogen adsorption is impeded by covalent metal-metal bonds in early transition metal paddle wheels from Sc to Cr and by the strong ferromagnetic coupling of diatomic Mn and Fe in the paddle wheel configurations.more » A significantly enhanced H{sub 2} adsorption is predicted in the nonmagnetic Co{sub 2} and Zn{sub 2} paddle wheel with the binding energy of {approx}0.2 eV per H{sub 2}. We also propose the use of two-dimensional Co{sub 2} and Zn{sub 2} paddle wheel frameworks that could have strongly adsorbed dihydrogen up to 1.35 wt % for noncryogenic hydrogen storage applications.« less

Aerodynamic analysis of an isolated vehicle wheel

NASA Astrophysics Data System (ADS)

Leśniewicz, P.; Kulak, M.; Karczewski, M.

2014-08-01

Increasing fuel prices force the manufacturers to look into all aspects of car aerodynamics including wheels, tyres and rims in order to minimize their drag. By diminishing the aerodynamic drag of vehicle the fuel consumption will decrease, while driving safety and comfort will improve. In order to properly illustrate the impact of a rotating wheel aerodynamics on the car body, precise analysis of an isolated wheel should be performed beforehand. In order to represent wheel rotation in contact with the ground, presented CFD simulations included Moving Wall boundary as well as Multiple Reference Frame should be performed. Sliding mesh approach is favoured but too costly at the moment. Global and local flow quantities obtained during simulations were compared to an experiment in order to assess the validity of the numerical model. Results of investigation illustrates dependency between type of simulation and coefficients (drag and lift). MRF approach proved to be a better solution giving result closer to experiment. Investigation of the model with contact area between the wheel and the ground helps to illustrate the impact of rotating wheel aerodynamics on the car body.

Effect of short-term prefeeding and body weight on wheel running and responding reinforced by the opportunity to run in a wheel.

PubMed

Belke, Terry W; Pierce, W David; Jensen, K

2004-07-30

A biobehavioural analysis of activity anorexia suggests that the motivation for physical activity is regulated by food supply and body weight. In the present experiment, food allocation was varied within subjects by prefeeding food-deprived rats 0, 5, 10 and 15 g of food before sessions of lever pressing for wheel-running reinforcement. The experiment assessed the effects of prefeeding on rates of wheel running, lever pressing, and postreinforcement pausing. Results showed that prefeeding animals 5 g of food had no effect. Prefeeding 10 g of food reduced lever pressing for wheel running and rates of wheel running without a significant change in body weight; the effect was, however, transitory. Prefeeding 15 g of food increased the animals' body weights, resulting in a sustained decrease of wheel running and lever pressing, and an increase in postreinforcement pausing. Overall the results indicate that the motivation for physical activity is regulated by changes in local food supply, but is sustained only when there is a concomitant change in body weight.

Dynamic interaction of rotating momentum wheels with spacecraft elements

NASA Astrophysics Data System (ADS)

Shankar Narayan, S.; Nair, P. S.; Ghosal, Ashitava

2008-09-01

In modern spacecraft with the requirement of increased accuracy of payloads, the on-orbit structural dynamic behavior of spacecraft is increasingly influencing the design and performance of spacecraft. During the integrated spacecraft testing of one of the satellites, a strong coupling between rotating momentum wheels and an earth sensor was detected. This resulted in corruption of the earth sensor data at certain wheel speeds. This paper deals with the dynamic coupling problem of a rotating momentum wheel with its support brackets affecting other subsystems of spacecraft. As part of this investigation, extensive modal tests and vibration tests were carried out on the momentum wheel bracket assembly with wheels in stationary and rotating conditions. It was found that the effects of gyroscopic forces arising out of rotating wheels are significant and this aspect needs to be taken into account while designing the mounting brackets. Results of analysis and tests were used to redesign the bracket leading to a significant reduction in the interaction and associated problems. A procedure for design of a support structure using a low-order mathematical model is also shown.

Mixing Enthalpies of TbBr3-MBr Liquid Mixtures

NASA Astrophysics Data System (ADS)

Rycerz, L.; Gaune-Escard, M.

2001-12-01

The molar enthalpies of mixing, Δmix Hm in the binary liquid systems TbBr3-MBr (M = Li, Na, K, Rb, Cs) have been m easured with a Calvet-type high-tem perature microcalorimeter over the entire composition range with an accuracy of about 6 %. Mixing of the two liquid components was achieved by using the "break-off am poule" technique. All the investigated systems show negative enthalpies of mixing with a minim um value of approxim ately -1.25, - 8 .3 , -17.0, - 2 0 . 0 and -22.5 kJ mol -1, for M = Li, Na, K, Rb and Cs, respectively. The mixing enthalpy in the TbBr3- LiBr system is positive in the TbBr3-rich region. For all the systems, the enthalpy minimum occurs at mole fraction xTbBr3 ≈ 0.3 - 0.4. The molar enthalpies of form ation Δ formHm (3MBr, TbBr3, 1) for M = Li, Na, K, Rb and Cs at 1113 K (arising from the reaction 3M Br(1) +TbBr3(1) = (3MBr, TbBr3) (1)) are found to be -4 .8 , -31.3, -63.3, -70.3 and -8 1 .2 kJ mol-1 , respectively. The leastsquares coefficients A, B, C, D and E in the equation λ (kJ mol-1) = A + B x + C x2 + Dx3 + Ex4, where A is an interaction param eter and x = xTbBr , are also reported.

Thermodynamic analysis of the interaction of partially hydrophobic cationic polyelectrolytes with sodium halide salts in water

NASA Astrophysics Data System (ADS)

Bončina, Matjaž; Lukšič, Miha; Seručnik, Mojca; Vlachy, Vojko

2014-05-01

Isothermal titration calorimetry was used to determine the temperature and concentration dependence of the enthalpy of mixing of 3,3- and 6,6-ionene fluorides, bromides, and iodides with low molecular weight salts (NaF, NaCl, NaBr, and NaI) in water. The magnitudes of the enthalpies, measured in the temperature range from 273 to 318 K, depended on the number of methylene groups on the ionene polyion (hydrophobicity), and on the anion of the added salt (ion-specificity). All enthalpies of mixing of 3,3- and 6,6-ionene fluorides with low molecular weight salts (NaCl, NaBr, and NaI) were negative, which is in contrast to the predictions of standard theories of polyelectrolyte solutions. This fact was interpreted in the light of the ion-water short-range interactions that are not accounted for in those theories. In contrast, the enthalpies of mixing of 3,3- and 6,6-ionene bromides and iodides with NaF were positive, being in accord with theory. Using the calorimetric data, we performed a model thermodynamic analysis of the polyelectrolyte-salt mixing process to obtain changes in the apparent standard Gibbs free energy, enthalpy, entropy, and heat capacity relative to the pure ionene fluorides in water. The results prove that halide ions replace fluoride counterions with a strength increasing in the order chloride < bromide < iodide. The process is enthalpy governed, accompanied by a positive change in the heat capacity.

Thermodynamic foundations of applications of ab initio methods for determination of the adsorbate equilibria: hydrogen at the GaN(0001) surface.

PubMed

Kempisty, Pawel; Strąk, Paweł; Sakowski, Konrad; Kangawa, Yoshihiro; Krukowski, Stanisław

2017-11-08

Thermodynamic foundations of ab initio modeling of vapor-solid and vapor-surface equilibria are introduced. The chemical potential change is divided into enthalpy and entropy terms. The enthalpy path passes through vapor-solid transition at zero temperature. The entropy path avoids the singular point at zero temperature passing a solid-vapor transition under normal conditions, where evaporation entropy is employed. In addition, the thermal changes are calculated. The chemical potential difference contribution of the following terms: vaporization enthalpy, vaporization entropy, the temperature-entropy related change, the thermal enthalpy change and mechanical pressure is obtained. The latter term is negligibly small for the pressure typical for epitaxy. The thermal enthalpy change is two orders smaller than the first three terms which have to be taken into account explicitly. The configurational vaporization entropy change is derived for adsorption processes. The same formulation is derived for vapor-surface equilibria using hydrogen at the GaN(0001) surface as an example. The critical factor is the dependence of the enthalpy of evaporation (desorption energy) on the pinning of the Fermi level bringing a drastic change of the value from 2.24 eV to -2.38 eV. In addition it is shown that entropic contributions considerable change the hydrogen equilibrium pressure over the GaN(0001) surface by several orders of magnitude. Thus a complete and exact formulation of vapor-solid and vapor-surface equilibria is presented.

Stabilization of the wheel running phenotype in mice.

PubMed

Bowen, Robert S; Cates, Brittany E; Combs, Eric B; Dillard, Bryce M; Epting, Jessica T; Foster, Brittany R; Patterson, Shawnee V; Spivey, Thomas P

2016-03-01

Increased physical activity is well known to improve health and wellness by modifying the risks for many chronic diseases. Rodent wheel running behavior is a beneficial surrogate model to evaluate the biology of daily physical activity in humans. Upon initial exposure to a running wheel, individual mice differentially respond to the experience, which confounds the normal activity patterns exhibited in this otherwise repeatable phenotype. To promote phenotypic stability, a minimum seven-day (or greater) acclimation period is utilized. Although phenotypic stabilization is achieved during this 7-day period, data to support acclimation periods of this length are not currently available in the literature. The purpose of this project is to evaluate the wheel running response in C57BL/6j mice immediately following exposure to a running wheel. Twenty-eight male and thirty female C57BL/6j mice (Jackson Laboratory, Bar Harbor, ME) were acquired at eight weeks of age and were housed individually with free access to running wheels. Wheel running distance (km), duration (min), and speed (m∙min(-1)) were measured daily for fourteen days following initial housing. One-way ANOVAs were used to evaluate day-to-day differences in each wheel running character. Limits of agreement and mean difference statistics were calculated between days 1-13 (acclimating) and day 14 (acclimated) to assess day-to-day agreement between each parameter. Wheel running distance (males: F=5.653, p=2.14 × 10(-9); females: F=8.217, p=1.20 × 10(-14)), duration (males: F=2.613, p=0.001; females: F=4.529, p=3.28 × 10(-7)), and speed (males: F=7.803, p=1.22 × 10(-13); females: F=13.140, p=2.00 × 10(-16)) exhibited day-to-day differences. Tukey's HSD post-hoc testing indicated differences between early (males: days 1-3; females: days 1-6) and later (males: days >3; females: days >6) wheel running periods in distance and speed. Duration only exhibited an anomalous difference between wheel running on day 13 and wheel running on days 1 through 4 in males. In females, duration exhibited anomalous differences due to abnormally depressed wheel running on day 6 and abnormally elevated wheel running on day 14. Limits of agreement and mean difference statistics indicated stable phenotypic variability with an up-trending daily mean for distance and speed that stabilized within the first three days in males and within eight days in females. Duration exhibited stable variability after nine days in males and after seven days in females. Although it is common practice to allow a prolonged (≥ seven day) acclimation period prior to recording wheel running data, the current study suggests that phenotypic stabilization of all three indices is achieved at different times with distance and speed exhibiting stability by day three in males and day eight in females. Duration exhibits stability by day nine in males and day seven in females. Copyright © 2015 Elsevier Inc. All rights reserved.

Review of Rail Behavior Under Wheel/Rail Impact Loading

DOT National Transportation Integrated Search

1986-04-01

The report discusses several studies involving factors that significantly affect rail life, particularly wheel impact loads. Parameters that characterize the effect of wheel impact loads on rail behavior are examined in terms of system variables such...

49 CFR 238.119 - Rim-stamped straight-plate wheels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... input to the wheel during braking. (b) A rim-stamped straight-plate wheel shall not be used as a... that is periodically tread-braked for a short duration by automatic circuitry for the sole purpose of...

Annular Momentum Control Device (AMCD). Volume 1: Laboratory model development

NASA Technical Reports Server (NTRS)

1975-01-01

The annular momentum control device (AMCD) a thin hoop-like wheel with neither shaft nor spokes is described. The wheel floats in a magnetic field and can be rotated by a segmented motor. Potential advantages of such a wheel are low weight, configuration flexibility, a wheel that stiffens with increased speed, vibration isolation, and increased reliability. The analysis, design, fabrication, and testing is described of the laboratory model of the AMCD.

76 FR 73771 - Denial of Motor Vehicle Defect Petition, DP10-002

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-29

...This notice describes the reasons for denying a petition (DP10-002) submitted to NHTSA under 49 U.S.C. Subtitle B, Chapter V, Part 552, Subpart A, requesting that the agency conduct ``an investigation of defective products manufactured by Dayton Wheel Concepts, Inc. (`Dayton Wheel' and American Wire Wheel, LLC (`American Wheel').'' The petition listed the allegedly defective products and the alleged defect (which varied by allegedly defective product).

23. DETAIL VIEW OF THE CLUTCH MECHANISM FOR THE MILL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. DETAIL VIEW OF THE CLUTCH MECHANISM FOR THE MILL POWER DISTRIBUTION SYSTEM FROM LEFT TO RIGHT. TRANSFER WHEEL WITH A BELT THAT CONNECTS TO THE DRIVE WHEEL OF THE MAIN POWER SHAFT. THE CLUTCH MECHANISM, THE DRIVE WHEEL THAT RECEIVED ITS POWER FROM A BELT CONNECTED TO TRANSFER WHEEL IN THE ELECTRIC MOTOR ROOM (BEHIND CAMERA). - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Muller Mixer Fire - Lessons Learned

DTIC Science & Technology

1986-08-01

wheel National Engineering stainless steel Special Simpson Porto Muller equipped with two-200 pound muller wheels plus an inside and outside plow...The mixer wheels /plows revolve at approximately 18 RPM and are driven by an 1800 RPM 3 H.P. motor through a double belt sheave and gear box. The bowl...diameter is approximately 39 inches and 12 inches deep with the mulling wheels /plows geared to move in a counterclockwise rotation. All bays are

Magnetic bearing reaction wheel. [for spacecraft attitude control

NASA Technical Reports Server (NTRS)

Sabnis, A.; Schmitt, F.; Smith, L.

1976-01-01

The results of a program for the development, fabrication and functional test of an engineering model magnetically suspended reaction wheel are described. The reaction wheel develops an angular momentum of + or - 0.5 foot-pound-second and is intended for eventual application in the attitude control of long-life interplanetary and orbiting spacecraft. A description of the wheel design and its major performance characteristics is presented. Recommendations for flight prototype development are made.

Wheel brakes and their application to aircraft

NASA Technical Reports Server (NTRS)

Dowty, G H

1928-01-01

The advantages to be gained from braking have not been ignored, and in the search for a suitable method many schemes have been suggested and tried. Some of the methods discussed in this paper include: 1) increasing the height of the landing gear; 2) air brakes of various forms; 3) sprags on tail skid and axle; and 4) wheel brakes. This report focuses on the design of wheel brakes and wheel brake controls.

The CRREL Instrumented Vehicle: Hardware and Software.

DTIC Science & Technology

1983-01-01

rear axle torque are meas- ured. The vehicle is equipped for front-wheel, rear-wheel or four-wheel drive. A dual brake system allows front-, rear- or...four-wheel braking . A minicomputer- based data acquisition system is installed in the vehicle to control data gather ing and to process the data. The...o..o...o 4 4. Dual brake system control valves . ........ 5 5. Schematic of modified brake system ...... .... st 5 6. Air-shock-absorber regulator

Analysis of wheel rim - Material and manufacturing aspects

NASA Astrophysics Data System (ADS)

Misra, Sheelam; Singh, Abhiraaj; James, Eldhose

2018-05-01

The tire in an automobile is supported by the rim of the wheel and its shape and dimensions should be adjusted to accommodate a specified tire. In this study, a tire of car wheel rim belonging to the disc wheel category is considered. Design is an important industrial operation used to define and specify the quality of the product. The design and modelling reduces the risk of damage involved in the manufacturing process. The design performed on this wheel rim is done on modelling software. After designing the model, it is imported for analysis purposes. The analysis software is used to calculate the different types of force, stresses, torque, and pressures acting upon the rim of the wheel and it reduces the time spent by a human for mathematical calculations. The analysis carried out considers two different materials namely structural steel and aluminium. Both materials are analyzed and their performance is noted.

Stocks and flows of lead-based wheel weights in the United States

USGS Publications Warehouse

Bleiwas, Donald I.

2006-01-01

Lead is used in many widely known applications, such as automobile batteries and radiation shielding. Another lesser known, but long-term, use of lead is in automotive vehicle wheel weights. Lead weights have been used to balance wheels since the 1930s because of its high specific gravity, low relative cost, and its malleability. Out-of-balance tires tend to 'cup' and vibrate and as a result cause excessive wear on tires and vehicle suspension components and result in compromised handling, especially at high speeds. The mass, number, and style of weights needed to balance a wheel depend on the tire's size and weight and on the type and condition of the wheels (rims) on the vehicle. This study addresses an accounting of the stocks and flows of lead contained in lead wheel weights from their manufacture, through use, dissipation, and recycling, and environmental issues associated with the use of lead.

Impediment to Spirit Drive on Sol 1806

NASA Technical Reports Server (NTRS)

2009-01-01

The hazard avoidance camera on the front of NASA's Mars Exploration Rover Spirit took this image after a drive by Spirit on the 1,806th Martian day, or sol, (January 31, 2009) of Spirit's mission on the surface of Mars.

The wheel at the bottom right of the image is Spirit's right-front wheel. Because that wheel no longer turns, Spirit drives backwards dragging that wheel. The drive on Sol 1806 covered about 30 centimeters (1 foot). The rover team had planned a longer drive, but Spirit stopped short, apparently from the right front wheel encountering the partially buried rock visible next to that wheel.

The hazard avoidance cameras on the front and back of the rover provide wide-angle views. The hill on the horizon in the right half of this image is Husband Hill. Spirit reached the summit of Husband Hill in 2005.

On the dynamic response at the wheel axle of a pneumatic tire

NASA Astrophysics Data System (ADS)

Kung, L. E.; Soedel, W.; Yang, T. Y.

1986-06-01

A method for calculating the steady state displacement response and force transmission at the wheel axle of a pneumatic tire-suspension system due to a steady state force or displacement excitation at the tire to ground contact point is developed. The method requires the frequency responses (or receptances)_of both tire-wheel and suspension units. The frequency response of the tire-wheel unit is obtained by using the modal expansion method. The natural frequencies and mode shapes of the tire-wheel unit are obtained by using a geometrically non-linear, ring type, thin shell finite element of laminate composite. The frequency response of the suspension unit is obtained analytically. These frequency responses are used to calculate the force-input and the displacement-input responses at the wheel axle. This method allows the freedom of designing a vehicle and its tires independently and still achieving optimum dynamic performance.

A third-order approximation method for three-dimensional wheel-rail contact

NASA Astrophysics Data System (ADS)

Negretti, Daniele

2012-03-01

Multibody train analysis is used increasingly by railway operators whenever a reliable and time-efficient method to evaluate the contact between wheel and rail is needed; particularly, the wheel-rail contact is one of the most important aspects that affects a reliable and time-efficient vehicle dynamics computation. The focus of the approach proposed here is to carry out such tasks by means of online wheel-rail elastic contact detection. In order to improve efficiency and save time, a main analytical approach is used for the definition of wheel and rail surfaces as well as for contact detection, then a final numerical evaluation is used to locate contact. The final numerical procedure consists in finding the zeros of a nonlinear function in a single variable. The overall method is based on the approximation of the wheel surface, which does not influence the contact location significantly, as shown in the paper.

Analysis of torque transmitting behavior and wheel slip prevention control during regenerative braking for high speed EMU trains

NASA Astrophysics Data System (ADS)

Xu, Kun; Xu, Guo-Qing; Zheng, Chun-Hua

2016-04-01

The wheel-rail adhesion control for regenerative braking systems of high speed electric multiple unit trains is crucial to maintaining the stability, improving the adhesion utilization, and achieving deep energy recovery. There remain technical challenges mainly because of the nonlinear, uncertain, and varying features of wheel-rail contact conditions. This research analyzes the torque transmitting behavior during regenerative braking, and proposes a novel methodology to detect the wheel-rail adhesion stability. Then, applications to the wheel slip prevention during braking are investigated, and the optimal slip ratio control scheme is proposed, which is based on a novel optimal reference generation of the slip ratio and a robust sliding mode control. The proposed methodology achieves the optimal braking performance without the wheel-rail contact information. Numerical simulation results for uncertain slippery rails verify the effectiveness of the proposed methodology.

Two wheeled lunar dumptruck

NASA Technical Reports Server (NTRS)

Brus, Michael R.; Haleblain, Ray; Hernandez, Tomas L.; Jensen, Paul E.; Kraynick, Ronald L.; Langley, Stan J.; Shuman, Alan G.

1988-01-01

The design of a two wheel bulk material transport vehicle is described in detail. The design consists of a modified cylindrical bowl, two independently controlled direct drive motors, and two deformable wheels. The bowl has a carrying capacity of 2.8 m (100 ft) and is constructed of aluminum. The low speed, high HP motors are directly connected to the wheels, thus yielding only two moving parts. The wheels, specifically designed for lunar applications, utilize the chevron tread pattern for optimum traction. The vehicle is maneuvered by varying the relative angular velocities of the wheels. The bulk material being transported is unloaded by utilizing the motors to oscillate the bowl back and forth to a height at which dumping is achieved. The analytical models were tested using a scaled prototype of the lunar transport vehicle. The experimental data correlated well with theoretical predictions. Thus, the design established provides a feasible alternative for the handling of bulk material on the moon.

Development and performance characterization of an electric ground vehicle with independently actuated in-wheel motors

NASA Astrophysics Data System (ADS)

Wang, Rongrong; Chen, Yan; Feng, Daiwei; Huang, Xiaoyu; Wang, Junmin

This paper presents the development and experimental characterizations of a prototyping pure electric ground vehicle, which is equipped with four independently actuated in-wheel motors (FIAIWM) and is powered by a 72 V 200 Ah LiFeYPO 4 battery pack. Such an electric ground vehicle (EGV) employs four in-wheel (or hub) motors to independently drive/brake the four wheels and is one of the promising vehicle architectures primarily due to its actuation flexibility, energy efficiency, and performance potentials. Experimental data obtained from the EGV chassis dynamometer tests were employed to generate the in-wheel motor torque response and power efficiency maps in both driving and regenerative braking modes. A torque distribution method is proposed to show the potentials of optimizing the FIAIWM EGV operational energy efficiency by utilizing the actuation flexibility and the characterized in-wheel motor efficiency and torque response.

Investigation of rail wheel steel crystallographic texture changes due to modification and thermomechanical treatment

NASA Astrophysics Data System (ADS)

Lychagina, T.; Nikolayev, D.; Sanin, A.; Tatarko, J.; Ullemeyer, K.

2015-04-01

In this work crystallographic texture for a set of rail wheel steel samples with different regimes of thermo-mechanical treatment and with and without modification by system Al-Mg-Si- Fe-C-Ca-Ti-Ce was measured by neutron diffraction. The texture measurements were carried out by using time-of-flight technique at SKAT diffractometer situated at IBR-2 reactor (Dubna, JINR, Russia). The three complete pole figures (110), (200), (211) of α-Fe phase in 5°×5°grid were extracted from a set of 1368 spectra measured for each sample. The samples were cut from rail wheel rim and from transitional zone (between rail wheel hub and wheel disk). It was concluded that the steel modification and some changes in the heat treatment modes of the rail wheels from the experimental (modified) and the conventional (non-modified) steel lead to reorientation of texture component.

Analytic and simulation studies on the use of torque-wheel actuators for the control of flexible robotic arms

NASA Technical Reports Server (NTRS)

Montgomery, Raymond C.; Ghosh, Dave; Kenny, Sean

1991-01-01

This paper presents results of analytic and simulation studies to determine the effectiveness of torque-wheel actuators in suppressing the vibrations of two-link telerobotic arms with attached payloads. The simulations use a planar generic model of a two-link arm with a torque wheel at the free end. Parameters of the arm model are selected to be representative of a large space-based robotic arm of the same class as the Space Shuttle Remote Manipulator, whereas parameters of the torque wheel are selected to be similar to those of the Mini-Mast facility at the Langley Research Center. Results show that this class of torque-wheel can produce an oscillation of 2.5 cm peak-to-peak in the end point of the arm and that the wheel produces significantly less overshoot when the arm is issued an abrupt stop command from the telerobotic input station.

Entropy–enthalpy transduction caused by conformational shifts can obscure the forces driving protein–ligand binding

PubMed Central

Fenley, Andrew T.; Muddana, Hari S.; Gilson, Michael K.

2012-01-01

Molecular dynamics simulations of unprecedented duration now can provide new insights into biomolecular mechanisms. Analysis of a 1-ms molecular dynamics simulation of the small protein bovine pancreatic trypsin inhibitor reveals that its main conformations have different thermodynamic profiles and that perturbation of a single geometric variable, such as a torsion angle or interresidue distance, can select for occupancy of one or another conformational state. These results establish the basis for a mechanism that we term entropy–enthalpy transduction (EET), in which the thermodynamic character of a local perturbation, such as enthalpic binding of a small molecule, is camouflaged by the thermodynamics of a global conformational change induced by the perturbation, such as a switch into a high-entropy conformational state. It is noted that EET could occur in many systems, making measured entropies and enthalpies of folding and binding unreliable indicators of actual thermodynamic driving forces. The same mechanism might also account for the high experimental variance of measured enthalpies and entropies relative to free energies in some calorimetric studies. Finally, EET may be the physical mechanism underlying many cases of entropy–enthalpy compensation. PMID:23150595

Rates and mechanisms of the atomic oxygen reaction with nickel at elevated temperatures

NASA Technical Reports Server (NTRS)

Christian, J. D.; Gilbreath, W. P.

1973-01-01

The oxidation of nickel by atomic oxygen at pressure from 1 to 45 N/sq m between 1050 and 1250 K was investigated. In these ranges, the oxidation was found to follow the parobolic rate law, viz., K sub p = 0.0000114 exp(-13410/T) g squared/cm4/sec for films of greater than 1 micron thickness and was pressure independent. The activation enthalpy for the oxidation reaction was 112 + or - 11 kj/mole (27 + or - 3 kcal/mole). Of a number of possible mechanisms and defect structures considered, it was shown that the most likely was a saturated surface defect model for atomic oxidation, based on reaction activation enthalpies, impurity effects, pressure independence, and magnitudes of rates. A model judged somewhat less likely was one having doubly ionized cationic defects rate controlling in both atomic and molecular oxygen. From comparisons of the appropriate processes, the following enthalpy values were derived: enthalpy of activation (Ni diffusion in Ni0) = 110 + or - 30 kj/mole and standard enthalpy change for reaction formation (doubly ionized cation vacancies in Ni0 from atomic oxygen)= -9 + or - 25 kj/mole.

Coupling geophysical investigation with hydrothermal modeling to constrain the enthalpy classification of a potential geothermal resource.

USGS Publications Warehouse

White, Jeremy T.; Karakhanian, Arkadi; Connor, Chuck; Connor, Laura; Hughes, Joseph D.; Malservisi, Rocco; Wetmore, Paul

2015-01-01

An appreciable challenge in volcanology and geothermal resource development is to understand the relationships between volcanic systems and low-enthalpy geothermal resources. The enthalpy of an undeveloped geothermal resource in the Karckar region of Armenia is investigated by coupling geophysical and hydrothermal modeling. The results of 3-dimensional inversion of gravity data provide key inputs into a hydrothermal circulation model of the system and associated hot springs, which is used to evaluate possible geothermal system configurations. Hydraulic and thermal properties are specified using maximum a priori estimates. Limited constraints provided by temperature data collected from an existing down-gradient borehole indicate that the geothermal system can most likely be classified as low-enthalpy and liquid dominated. We find the heat source for the system is likely cooling quartz monzonite intrusions in the shallow subsurface and that meteoric recharge in the pull-apart basin circulates to depth, rises along basin-bounding faults and discharges at the hot springs. While other combinations of subsurface properties and geothermal system configurations may fit the temperature distribution equally well, we demonstrate that the low-enthalpy system is reasonably explained based largely on interpretation of surface geophysical data and relatively simple models.

A novel mouse running wheel that senses individual limb forces: biomechanical validation and in vivo testing

PubMed Central

Roach, Grahm C.; Edke, Mangesh

2012-01-01

Biomechanical data provide fundamental information about changes in musculoskeletal function during development, adaptation, and disease. To facilitate the study of mouse locomotor biomechanics, we modified a standard mouse running wheel to include a force-sensitive rung capable of measuring the normal and tangential forces applied by individual paws. Force data were collected throughout the night using an automated threshold trigger algorithm that synchronized force data with wheel-angle data and a high-speed infrared video file. During the first night of wheel running, mice reached consistent running speeds within the first 40 force events, indicating a rapid habituation to wheel running, given that mice generated >2,000 force-event files/night. Average running speeds and peak normal and tangential forces were consistent throughout the first four nights of running, indicating that one night of running is sufficient to characterize the locomotor biomechanics of healthy mice. Twelve weeks of wheel running significantly increased spontaneous wheel-running speeds (16 vs. 37 m/min), lowered duty factors (ratio of foot-ground contact time to stride time; 0.71 vs. 0.58), and raised hindlimb peak normal forces (93 vs. 115% body wt) compared with inexperienced mice. Peak normal hindlimb-force magnitudes were the primary force component, which were nearly tenfold greater than peak tangential forces. Peak normal hindlimb forces exceed the vertical forces generated during overground running (50-60% body wt), suggesting that wheel running shifts weight support toward the hindlimbs. This force-instrumented running-wheel system provides a comprehensive, noninvasive screening method for monitoring gait biomechanics in mice during spontaneous locomotion. PMID:22723628

Long term voluntary wheel running is rewarding and produces plasticity in the mesolimbic reward pathway

PubMed Central

Greenwood, Benjamin N.; Foley, Teresa E.; Le, Tony V.; Strong, Paul V.; Loughridge, Alice B.; Day, Heidi E.W.; Fleshner, Monika

2011-01-01

The mesolimbic reward pathway is implicated in stress-related psychiatric disorders and is a potential target of plasticity underlying the stress resistance produced by repeated voluntary exercise. It is unknown, however, whether rats find long-term access to running wheels rewarding, or if repeated voluntary exercise reward produces plastic changes in mesolimbic reward neurocircuitry. In the current studies, young adult, male Fischer 344 rats allowed voluntary access to running wheels for 6 weeks, but not 2 weeks, found wheel running rewarding, as measured by conditioned place preference (CPP). Consistent with prior reports and the behavioral data, 6 weeks of wheel running increased ΔFosB/FosB immunoreactivity in the nucleus accumbens (Acb). In addition, semi quantitative in situ hybridization revealed that 6 weeks of wheel running, compared to sedentary housing, increased tyrosine hydroxylase (TH) mRNA levels in the ventral tegmental area (VTA), increased delta opioid receptor (DOR) mRNA levels in the Acb shell, and reduced levels of dopamine receptor (DR)-D2 mRNA in the Acb core. Results indicate that repeated voluntary exercise is rewarding and alters gene transcription in mesolimbic reward neurocircuitry. The duration-dependent effects of wheel running on CPP suggest that as the weeks of wheel running progress, the rewarding effects of a night of voluntary wheel running might linger longer into the inactive cycle thus providing stronger support for CPP. The observed plasticity could contribute to the mechanisms by which exercise reduces the incidence and severity of substance abuse disorders, changes the rewarding properties of drugs of abuse, and facilitates successful coping with stress. PMID:21070820

Errors of car wheels rotation rate measurement using roller follower on test benches

NASA Astrophysics Data System (ADS)

Potapov, A. S.; Svirbutovich, O. A.; Krivtsov, S. N.

2018-03-01

The article deals with rotation rate measurement errors, which depend on the motor vehicle rate, on the roller, test benches. Monitoring of the vehicle performance under operating conditions is performed on roller test benches. Roller test benches are not flawless. They have some drawbacks affecting the accuracy of vehicle performance monitoring. Increase in basic velocity of the vehicle requires increase in accuracy of wheel rotation rate monitoring. It determines the degree of accuracy of mode identification for a wheel of the tested vehicle. To ensure measurement accuracy for rotation velocity of rollers is not an issue. The problem arises when measuring rotation velocity of a car wheel. The higher the rotation velocity of the wheel is, the lower the accuracy of measurement is. At present, wheel rotation frequency monitoring on roller test benches is carried out by following-up systems. Their sensors are rollers following wheel rotation. The rollers of the system are not kinematically linked to supporting rollers of the test bench. The roller follower is forced against the wheels of the tested vehicle by means of a spring-lever mechanism. Experience of the test bench equipment operation has shown that measurement accuracy is satisfactory at small rates of vehicles diagnosed on roller test benches. With a rising diagnostics rate, rotation velocity measurement errors occur in both braking and pulling modes because a roller spins about a tire tread. The paper shows oscillograms of changes in wheel rotation velocity and rotation velocity measurement system’s signals when testing a vehicle on roller test benches at specified rates.

The medial prefrontal cortex and nucleus accumbens mediate the motivation for voluntary wheel running in the rat.

PubMed

Basso, Julia C; Morrell, Joan I

2015-08-01

Voluntary wheel running in rats provides a preclinical model of exercise motivation in humans. We hypothesized that rats run because this activity has positive incentive salience in both the acquisition and habitual stages of wheel running and that gender differences might be present. Additionally, we sought to determine which forebrain regions are essential for the motivational processes underlying wheel running in rats. The motivation for voluntary wheel running in male and female Sprague-Dawley rats was investigated during the acquisition (Days 1-7) and habitual phases (after Day 21) of running using conditioned place preference (CPP) and the reinstatement (rebound) response after forced abstinence, respectively. Both genders displayed a strong CPP for the acquisition phase and a strong rebound response to wheel deprivation during the habitual phase, suggesting that both phases of wheel running are rewarding for both sexes. Female rats showed a 1.5 times greater rebound response than males to wheel deprivation in the habitual phase of running, while during the acquisition phase, no gender differences in CPP were found. We transiently inactivated the medial prefrontal cortex (mPFC) or the nucleus accumbens (NA), hypothesizing that because these regions are involved in the acquisition and reinstatement of self-administration of both natural and pharmacological stimuli, they might also serve a role in the motivation to wheel run. Inactivation of either structure decreased the rebound response in the habitual phase of running, demonstrating that these structures are involved in the motivation for this behavior. (c) 2015 APA, all rights reserved).

ATHLETE: Lunar Cargo Unloading from a High Deck

NASA Technical Reports Server (NTRS)

Wilcox, Brian H.

2010-01-01

As part of the NASA Exploration Technology Development Program, the Jet Propulsion Laboratory is developing a vehicle called ATHLETE: the All-Terrain Hex-Limbed Extra-Terrestrial Explorer. Each vehicle is based on six wheels at the ends of six multi-degree-of freedom limbs. Because each limb has enough degrees of freedom for use as a general-purpose leg, the wheels can be locked and used as feet to walk out of excessively soft or other extreme terrain. Since the vehicle has this alternative mode of traversing through or at least out of extreme terrain, the wheels and wheel actuators can be sized for nominal terrain. There are substantial mass savings in the wheel and wheel actuators associated with designing for nominal instead of extreme terrain. These mass savings are at least comparable-to or larger-than the extra mass associated with the articulated limbs. As a result, the entire mobility system, including wheels and limbs, can be lighter than a conventional all-terrain mobility chassis. A side benefit of this approach is that each limb has sufficient degrees-of freedom to be used as a general-purpose manipulator (hence the name "limb" instead of "leg"). Our prototype ATHLETE vehicles have quick-disconnect tool adapters on the limbs that allow tools to be drawn out of a "tool belt" and maneuvered by the limb. A power-take-off from the wheel actuates the tools, so that they can take advantage of the 1+ horsepower motor in each wheel to enable drilling, gripping or other power-tool functions.

ATHLETE: a Cargo and Habitat Transporter for the Moon

NASA Technical Reports Server (NTRS)

Wilcox, Brian H.

2009-01-01

As part of the NASA Exploration Technology Development Program, the Jet Propulsion Laboratory is developing a vehicle called ATHLETE: the All-Terrain Hex-Limbed Extra-Terrestrial Explorer. The vehicle concept is based on six wheels at the ends of six multi-degree-of-freedom limbs. Because each limb has enough degrees of freedom for use as a general-purpose leg, the wheels can be locked and used as feet to walk out of excessively soft or other extreme terrain. Since the vehicle has this alternative mode of traversing through (or at least out of) extreme terrain, the wheels and wheel actuators can be sized only for nominal terrain. There are substantial mass savings in the wheels and wheel actuators associated with designing for nominal instead of extreme terrain. These mass savings are comparable-to or larger-than the extra mass associated with the articulated limbs. As a result, the entire mobility system, including wheels and limbs, can be about 25 percent lighter than a conventional mobility chassis for planetary exploration. A side benefit of this approach is that each limb has sufficient degrees-of-freedom for use as a general-purpose manipulator (hence the name "limb" instead of "leg"). Our prototype ATHLETE vehicles have quick-disconnect tool adapters on the limbs that allow tools to be drawn out of a "tool belt" and maneuvered by the limb. A rotating power-take-off from the wheel actuates the tools, so that they can take advantage of the 1-plus-horsepower motor in each wheel to enable drilling, gripping or other power-tool functions.

Thermodynamics and Frozen Foods.

ERIC Educational Resources Information Center

Kerr, William L.; Reid, David S.

1993-01-01

The heat content of a food at a given temperature can be described by the thermodynamic property of enthalpy. Presents a method to construct a simple calorimeter for measuring the enthalpy changes of different foods during freezing. (MDH)

Wheel/Rail Noise and Vibration Control

DOT National Transportation Integrated Search

1974-05-01

Reported here are the interim results of a program under the UMTA Urban Rail Supporting Technology Program to develop a basic understanding of urban transit wheel/rail noise generation for application to the evaluation and improvement of wheel/rail n...

Estimation of residual stresses in railroad commuter car wheels following manufacture

DOT National Transportation Integrated Search

2003-06-01

A finite element simulation is presented for the prediction of : residual stresses resulting from the heat treatment of railroad : commuter car wheels during manufacture. The quenching and : annealing segments of the wheel manufacturing process are s...

Wheel inspection system environment qualification and validation : final report for public distribution.

DOT National Transportation Integrated Search

2009-03-20

International Electronic Machines Corporation (IEM) has developed and is now marketing a state-of-the-art Wheel Inspection System Environment (WISE). WISE provides wheel profile and dimensional measurements, i.e. rim thickness, flange height, flange ...

29 CFR 1926.303 - Abrasive wheels and tools.

Code of Federal Regulations, 2011 CFR

2011-07-01

... distance not to exceed one-eighth inch from the surface of the wheel. (3) Cup type wheels used for external grinding shall be protected by either a revolving cup guard or a band type guard in accordance with the...

29 CFR 1926.303 - Abrasive wheels and tools.

Code of Federal Regulations, 2010 CFR

2010-07-01

... distance not to exceed one-eighth inch from the surface of the wheel. (3) Cup type wheels used for external grinding shall be protected by either a revolving cup guard or a band type guard in accordance with the...

29 CFR 1915.134 - Abrasive wheels.

Code of Federal Regulations, 2011 CFR

2011-07-01

... shall be kept a distance not to exceed 1/8 inch from the surface of the wheel. (c) Cup type wheels used for external grinding shall be protected by either a revolving cup guard or a band type guard in...

29 CFR 1915.134 - Abrasive wheels.

Code of Federal Regulations, 2010 CFR

2010-07-01

... shall be kept a distance not to exceed 1/8 inch from the surface of the wheel. (c) Cup type wheels used for external grinding shall be protected by either a revolving cup guard or a band type guard in...

76 FR 55708 - Servicing Multi-Piece and Single Piece Rim Wheels; Extension of the Office of Management and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-08

... strength requirements specified in the Standard, and a requirement that defective wheels and wheel... or a Registered Professional Engineer must certify that the strength requirements specified in (d)(3...

Using wheel temperature detector technology to monitor railcar brake system effectiveness.

DOT National Transportation Integrated Search

2013-12-01

Wheel temperature detector technology has been used extensively in the railroad industry for the past several decades. The : technology has traditionally been used to identify wheels with elevated temperatures. There is currently a movement in the : ...

Estimation of residual stresses in railroad commuter car wheels following manufacture

DOT National Transportation Integrated Search

1998-11-01

A finite element simulation is presented for the prediction of residual stresses resulting from the heat treatment of railroad commuter car wheels during manufacture. The quenching and annealing segments of the wheel manufacturing process are simulat...

Wheel climb derailment criteria for evaluation of rail vehicle safety

DOT National Transportation Integrated Search

1984-01-01

Criteria for evaluating safety of rail vehicles with respect to wheel climb derailment are reviewed. The relationship between flanging wheel lateral to veritical force ratio at impending derailment and angle of attack, lateral velocity and longitudin...

Variability in bimanual wheelchair propulsion: consistency of two instrumented wheels during handrim wheelchair propulsion on a motor driven treadmill

PubMed Central

2013-01-01

Background Handrim wheelchair propulsion is a complex bimanual motor task. The bimanually applied forces on the rims determine the speed and direction of locomotion. Measurements of forces and torques on the handrim are important to study status and change of propulsion technique (and consequently mechanical strain) due to processes of learning, training or the wheelchair configuration. The purpose of this study was to compare the simultaneous outcomes of two different measurement-wheels attached to the different sides of the wheelchair, to determine measurement consistency within and between these wheels given the expected inter- and intra-limb variability as a consequence of motor control. Methods Nine able-bodied subjects received a three-week low-intensity handrim wheelchair practice intervention. They then performed three four-minute trials of wheelchair propulsion in an instrumented hand rim wheelchair on a motor-driven treadmill at a fixed belt speed. The two measurement-wheels on each side of the wheelchair measured forces and torques of one of the two upper limbs, which simultaneously perform the push action over time. The resulting data were compared as direct output using cross-correlation on the torque around the wheel-axle. Calculated push characteristics such as power production and speed were compared using an intra-class correlation. Results Measured torque around the wheel axle of the two measurement-wheels had a high average cross-correlation of 0.98 (std=0.01). Unilateral mean power output over a minute was found to have an intra-class correlation of 0.89 between the wheels. Although the difference over the pushes between left and right power output had a high variability, the mean difference between the measurement-wheels was low at 0.03 W (std=1.60). Other push characteristics showed even higher ICC’s (>0.9). Conclusions A good agreement between both measurement-wheels was found at the level of the power output. This indicates a high comparability of the measurement-wheels for the different propulsion parameters. Data from both wheels seem suitable to be used together or interchangeably in experiments on motor control and wheelchair propulsion performance. A high variability in forces and timing between the left and right side were found during the execution of this bimanual task, reflecting the human motor control process. PMID:23360756

Variability in bimanual wheelchair propulsion: consistency of two instrumented wheels during handrim wheelchair propulsion on a motor driven treadmill.

PubMed

Vegter, Riemer J K; Lamoth, Claudine J; de Groot, Sonja; Veeger, Dirkjan H E J; van der Woude, Lucas H V

2013-01-29

Handrim wheelchair propulsion is a complex bimanual motor task. The bimanually applied forces on the rims determine the speed and direction of locomotion. Measurements of forces and torques on the handrim are important to study status and change of propulsion technique (and consequently mechanical strain) due to processes of learning, training or the wheelchair configuration. The purpose of this study was to compare the simultaneous outcomes of two different measurement-wheels attached to the different sides of the wheelchair, to determine measurement consistency within and between these wheels given the expected inter- and intra-limb variability as a consequence of motor control. Nine able-bodied subjects received a three-week low-intensity handrim wheelchair practice intervention. They then performed three four-minute trials of wheelchair propulsion in an instrumented hand rim wheelchair on a motor-driven treadmill at a fixed belt speed. The two measurement-wheels on each side of the wheelchair measured forces and torques of one of the two upper limbs, which simultaneously perform the push action over time. The resulting data were compared as direct output using cross-correlation on the torque around the wheel-axle. Calculated push characteristics such as power production and speed were compared using an intra-class correlation. Measured torque around the wheel axle of the two measurement-wheels had a high average cross-correlation of 0.98 (std=0.01). Unilateral mean power output over a minute was found to have an intra-class correlation of 0.89 between the wheels. Although the difference over the pushes between left and right power output had a high variability, the mean difference between the measurement-wheels was low at 0.03 W (std=1.60). Other push characteristics showed even higher ICC's (>0.9). A good agreement between both measurement-wheels was found at the level of the power output. This indicates a high comparability of the measurement-wheels for the different propulsion parameters. Data from both wheels seem suitable to be used together or interchangeably in experiments on motor control and wheelchair propulsion performance. A high variability in forces and timing between the left and right side were found during the execution of this bimanual task, reflecting the human motor control process.

A Century-Old Question: Does a Crookes Paddle Wheel Cathode Ray Tube Demonstrate that Electrons Carry Momentum?

NASA Astrophysics Data System (ADS)

Humphrey, T. E.; Calisa, Vaishnavi

2014-03-01

In 1879, in the midst of the debate between English and continental scientists about the nature of cathode rays, William Crookes conducted an experiment in which a small mill or "paddle wheel" was pushed along tracks inside a cathode ray tube (CRT) (similar to that shown in Fig. 1) when connected to a high-voltage induction coil. Crookes attributed the motion of the wheel to momentum transfer from the cathode rays (electrons) to the wheel, and interpreted the experiment as providing evidence that cathode rays were particles. In 1903 Thomson discounted Crookes' interpretation by calculating that the rate of momentum transfer (which he estimated at no more than 2×10-3 dyn, equivalent to 2×10-8 N) would be far too small to account for the observed motion of the wheel,2 instead attributing the motion to the radiometric effect. The misconception was not laid to rest, however, and despite an effort in 1961 to draw attention to Thomson's original work and so remove the error from textbooks,3 the notion that a Crookes paddle wheel CRT demonstrates that electrons carry momentum continues to be taught in high school physics courses4 and wheel. We then measured the actual acceleration of the wheel in the CRT by video analysis of its motion and determined the moment of inertia of the wheel along with its mass and dimensions. We could then compare the force, which really acts on the wheel to produce the observed motion to the maximum impulsive force that is supplied by the electrons. Our measurements yield a maximum impulsive force due to the electrons [ F e l = ( 1.1 ± 0.3 ) × 10 - 8 N ], which is within a factor of two of Thomson's estimate, and which is more than two orders of magnitude smaller than the force that is responsible for the observed acceleration of the paddle wheel [ F W = ( 6 ± 2 ) × 10 - 6 N ]. This means that the rotation of the wheel is certainly not due to transferred momentum from the electron beam, and the results of the experiment should not be taught to students as proof that electrons are particles with mass that carry momentum.

Exercise training effects on hypoxic and hypercapnic ventilatory responses in mice selected for increased voluntary wheel running.

PubMed

Kelly, Scott A; Rezende, Enrico L; Chappell, Mark A; Gomes, Fernando R; Kolb, Erik M; Malisch, Jessica L; Rhodes, Justin S; Mitchell, Gordon S; Garland, Theodore

2014-02-01

What is the central question of this study? We used experimental evolution to determine how selective breeding for high voluntary wheel running and exercise training (7-11 weeks) affect ventilatory chemoreflexes of laboratory mice at rest. What is the main finding and its importance? Selective breeding, although significantly affecting some traits, did not systematically alter ventilation across gas concentrations. As with most human studies, our findings support the idea that endurance training attenuates resting ventilation. However, little evidence was found for a correlation between ventilatory chemoreflexes and the amount of individual voluntary wheel running. We conclude that exercise 'training' alters respiratory behaviours, but these changes may not be necessary to achieve high levels of wheel running. Ventilatory control is affected by genetics, the environment and gene-environment and gene-gene interactions. Here, we used an experimental evolution approach to test whether 37 generations of selective breeding for high voluntary wheel running (genetic effects) and/or long-term (7-11 weeks) wheel access (training effects) alter acute respiratory behaviour of mice resting in normoxic, hypoxic and hypercapnic conditions. As the four replicate high-runner (HR) lines run much more than the four non-selected control (C) lines, we also examined whether the amount of exercise among individual mice was a quantitative predictor of ventilatory chemoreflexes at rest. Selective breeding and/or wheel access significantly affected several traits. In normoxia, HR mice tended to have lower mass-adjusted rates of oxygen consumption and carbon dioxide production. Chronic wheel access increased oxygen consumption and carbon dioxide production in both HR and C mice during hypercapnia. Breathing frequency and minute ventilation were significantly reduced by chronic wheel access in both HR and C mice during hypoxia. Selection history, while significantly affecting some traits, did not systematically alter ventilation across all gas concentrations. As with most human studies, our findings support the idea that endurance training (access to wheel running) attenuates resting ventilation. However, little evidence was found for a correlation at the level of the individual variation between ventilatory chemoreflexes and performance (amount of individual voluntary wheel running). We tentatively conclude that exercise 'training' alters respiratory behaviours, but these changes may not be necessary to achieve high levels of wheel running.

Effects of intrinsic aerobic capacity and ovariectomy on voluntary wheel running and nucleus accumbens dopamine receptor gene expression.

PubMed

Park, Young-Min; Kanaley, Jill A; Padilla, Jaume; Zidon, Terese; Welly, Rebecca J; Will, Matthew J; Britton, Steven L; Koch, Lauren G; Ruegsegger, Gregory N; Booth, Frank W; Thyfault, John P; Vieira-Potter, Victoria J

2016-10-01

Rats selectively bred for high (HCR) and low (LCR) aerobic capacity show a stark divergence in wheel running behavior, which may be associated with the dopamine (DA) system in the brain. HCR possess greater motivation for voluntary running along with greater brain DA activity compared to LCR. We recently demonstrated that HCR are not immune to ovariectomy (OVX)-associated reductions in spontaneous cage (i.e. locomotor) activity. Whether HCR and LCR rats differ in their OVX-mediated voluntary wheel running response is unknown. To determine whether HCR are protected from OVX-associated reduction in voluntary wheel running. Forty female HCR and LCR rats (age ~27weeks) had either SHM or OVX operations, and given access to a running wheel for 11weeks. Weekly wheel running distance was monitored throughout the intervention. Nucleus accumbens (NAc) was assessed for mRNA expression of DA receptors at sacrifice. Compared to LCR, HCR ran greater distance and had greater ratio of excitatory/inhibitory DA mRNA expression (both line main effects, P<0.05). Wheel running distance was significantly, positively correlated with the ratio of excitatory/inhibitory DA mRNA expression across animals. In both lines, OVX reduced wheel running (P<0.05). Unexpectedly, although HCR started with significantly greater voluntary wheel running, they had greater OVX-induced reduction in wheel running than LCR such that no differences were found 11weeks after OVX between HCROVX and LCROVX (interaction, P<0.05). This significant reduction in wheel running in HCR was associated with an OVX-mediated reduction in the ratio of excitatory/inhibitory DA mRNA expression. The DA system in the NAc region may play a significant role in motivation to run in female rats. Compared to LCR, HCR rats run significantly more, which associates with greater ratio of excitatory/inhibitory DA mRNA expression. However, despite greater inherent motivation to run and an associated brain DA mRNA expression profile, HCR rats are not protected against OVX-induced reduction in wheel running or OVX-mediated reduction in the ratio of excitatory/inhibitory DA receptor mRNA expression. OVX-mediated reduction in motivated physical activity may be partially explained by a reduced ratio of excitatory/inhibitory DA receptor mRNA expression for which intrinsic fitness does not confer protection. Copyright © 2016 Elsevier Inc. All rights reserved.