Evaluation of ADAM/1 model for advanced coal extraction concepts

NASA Technical Reports Server (NTRS)

Deshpande, G. K.; Gangal, M. D.

1982-01-01

Several existing computer programs for estimating life cycle cost of mining systems were evaluated. A commercially available program, ADAM/1 was found to be satisfactory in relation to the needs of the advanced coal extraction project. Two test cases were run to confirm the ability of the program to handle nonconventional mining equipment and procedures. The results were satisfactory. The model, therefore, is recommended to the project team for evaluation of their conceptual designs.

Detailed Test Plan Redundant Sensor Strapdown IMU Evaluation Program

NASA Technical Reports Server (NTRS)

Hartwell, T.; Miyatake, Y.; Wedekind, D. E.

1971-01-01

The test plan for a redundant sensor strapdown inertial measuring unit evaluation program is presented. The subjects discussed are: (1) test philosophy and limitations, (2) test sequence, (3) equipment specifications, (4) general operating procedures, (5) calibration procedures, (6) alignment test phase, and (7) navigation test phase. The data and analysis requirements are analyzed.

Spacelab Level 4 programmatic Implementation Assessment Study. Volume 3: Optimization and programmatics

NASA Technical Reports Server (NTRS)

1978-01-01

Alternate level 4 integration approaches were synthesized and evaluated to establish the most cost effective experiment integration approach. Program baseline system trade studies are described, as well as Spacelab equipment utilization. Programmatic analysis of the baseline program was evaluated; the 2/3 and 1/3 traffic models were also considered.

Computer program determines performance efficiency of remote measuring systems

NASA Technical Reports Server (NTRS)

Merewether, E. K.

1966-01-01

Computer programs control and evaluate instrumentation system performance for numerous rocket engine test facilities and prescribe calibration and maintenance techniques to maintain the systems within process specifications. Similar programs can be written for other test equipment in an industry such as the petrochemical industry.

Agricultural Equipment Technology: A Suggested 2-Year Post High School Curriculum.

ERIC Educational Resources Information Center

Office of Education (DHEW), Washington, DC.

Developed by a subject matter specialist, this suggested curriculum guide is intended to assist school administrators, advisory committees, supervisors, and teachers in planning and developing new programs or evaluating existing ones in agricultural equipment technology. The guide provides suggested course outlines, including examples of texts and…

SEABEE Pretest Results of the Joint Logistics-over-the-Shore (LOTS) Test and Evaluation Program.

DTIC Science & Technology

1977-12-07

in the harbor. None of the equipment required extensive shoring. Some chocks and * wedges were placed on the equipment to increase its stability. P...incident. A subsequent examination revealed considerable structural damage to *the Peck & Hale tie-downs. Evidently one of the latching devices

Development of a computer program to generate typical measurement values for various systems on a space station

NASA Technical Reports Server (NTRS)

Deacetis, Louis A.

1987-01-01

The elements of a simulation program written in Ada were developed. The program will eventually serve as a data generator of typical readings from various space station equipment involved with Communications and Tracking, and will simulate various scenarios that may arise due to equipment malfunction or failure, power failure, etc. In addition, an evaluation of the Ada language was made from the viewpoint of a FORTRAN programmer learning Ada for the first time. Various strengths and difficulties associated with the learning and use of Ada are considered.

Teaching Basic Cooking Skills: Evaluation of the North Carolina Extension "Cook Smart, Eat Smart" Program

ERIC Educational Resources Information Center

Dunn, Carolyn; Jayaratne, K. S. U.; Baughman, Kristen; Levine, Katrina

2014-01-01

Cook Smart, Eat Smart (CSES) is a 12-hour cooking school that teaches participants to prepare nutritious, delicious food using simple, healthy preparation techniques, basic ingredients, and minimal equipment. The purpose of this evaluation was to examine the impact of CSES on food preparation and meal consumption behavior. Program outcomes include…

Computer program for discounted cash flow/rate of return evaluations

NASA Technical Reports Server (NTRS)

Robson, W. D.

1971-01-01

Technique, incorporated into set of three computer programs, provides economic methodology for reducing all parameters to financially sound common denominator of present worth, and calculates resultant rate of return on new equipment, processes, or systems investments.

Title I, Part B, Institutionalized Facilities Program, Summer 1982. Annual Evaluation Report.

ERIC Educational Resources Information Center

New York City Board of Education, Brooklyn, NY. Office of Educational Evaluation.

This 1982 summer Title I, Part B, Institutionalized Facilities Program provided supplementary career instruction to 188 students residing in facilities for neglected and delinquent children and youth. This report briefly describes the program, providing information on methodology, physical setting, equipment, and supplies; population and class…

An Analysis of Audiovisual Machines for Individual Program Presentation. Research Memorandum Number Two.

ERIC Educational Resources Information Center

Finn, James D.; Weintraub, Royd

The Medical Information Project (MIP) purpose to select the right type of audiovisual equipment for communicating new medical information to general practitioners of medicine was hampered by numerous difficulties. There is a lack of uniformity and standardization in audiovisual equipment that amounts to chaos. There is no evaluative literature on…

Mobilizable RDF/d-RDF burning program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niemann, K.; Campbell, J.

1982-03-01

The Mobilizable RDF/d-RDF Burning Program was conceived to promote the utilization of refuse-derived fuels (RDF) as a supplement to existing fossil fuel sources in industrial-sized boilers. The program explores the design, development, and eventual construction of densified-RDF (d-RDF) for use in boiler combustion testing as a supplement to stoker coal or wood wastes. The equipment would be mounted on trailers and assembled and operated at preselected sites throughout the country where approximately 750 tons of RDF would be produced and test burned in a local boiler. The equipment, to include a transportable RDF boiler metering and feed system, would thenmore » be moved and operated at two to three test sites annually. The program is intended to encourage the construction of permanent resource recovery facilities by involving local waste handling groups in operating the equipment and producing fuel, and potential local fuel users in testing the fuel in their boilers. The Mobilizable Program was developed from two separate tasks. The first task developed the concept behind the program and defined its operational and organizational structure. The second task, a follow-up to the first, was intended principally to finalize test locations, develop equipment designs and specifications, and formalize a management program. This report summarizes the principal findings of both tasks. It identifies the criteria used to identify test locations, outlines the program's management structure, presents design and performance specifications for both the fuel production equipment and boiler fuel feed systems, and provides a detailed evaluation of the parameters involved in burning RDF in industrial-sized boilers. Final conclusions and recommendations identify problem areas encountered in the program, and discuss possible future directions for such a program.« less

Football (soccer) safety equipment use and parental attitudes toward safety equipment in a community youth sports program.

PubMed

Khodaee, Morteza; Fetters, Michael D; Gorenflo, Daniel W

2011-04-01

While a growing number of children are playing football (soccer), there are limited data on prevalence of injuries, actual use of football safety equipment (SE), and parental attitudes about football SE. We distributed a self-administered survey by mail to parents of all players enrolled in a community recreation youth football program. Parents of 865 children responded. Overall, 32 (3.7%) children were reported as having injuries requiring medical/dental evaluation. Upper/lower extremities were the most commonly injured sites. Shinguards (SGs) were the only equipment commonly used. While there was high parental support for SG use (97.4%) and moderate support for mouthguards (MGs; 53.8%), there was less support for other SE. Many parents were unfamiliar with available SE, but they were mostly willing to pay for it. In a community youth sports program, reports of football injuries were low as was the use of football SE other than SGs.

Missile airframe simulation testbed: MANPADS (MAST-M) for test and evaluation of aircraft survivability equipment

NASA Astrophysics Data System (ADS)

Clements, Jim; Robinson, Richard; Bunt, Leslie; Robinson, Joe

2011-06-01

A number of techniques have been utilized to evaluate the performance of Aircraft Survivability Equipment (ASE) against threat Man-Portable Air Defense Systems (MANPADS). These techniques include flying actual threat MANPADS against stationary ASE with simulated aircraft signatures, testing installed ASE systems against simulated threat signatures, and laboratory hardware-in-the-loop (HWIL) testing with simulated aircraft and simulated missile signatures. All of these tests lack the realism of evaluating installed ASE against in-flight MANPADS on a terminal homing intercept path toward the actual ASE equipped aircraft. This limitation is due primarily to the current inability to perform non-destructive MANPADS/Aircraft flight testing. The U.S. Army Aviation and Missile Research and Development and Engineering Center (AMRDEC) is working to overcome this limitation with the development of a recoverable surrogate MANPADS missile system capable of engaging aircraft equipped with ASE while guaranteeing collision avoidance with the test aircraft. Under its Missile Airframe Simulation Testbed - MANPADS (MAST-M) program, the AMRDEC is developing a surrogate missile system which will utilize actual threat MANPADS seeker/guidance sections to control the flight of a surrogate missile which will perform a collision avoidance and recovery maneuver prior to intercept to insure non-destructive test and evaluation of the ASE and reuse of the MANPADS seeker/guidance section. The remainder of this paper provides an overview of this development program and intended use.

Physical security equipment for combating terrorism

NASA Astrophysics Data System (ADS)

Toscano, Michael

2002-08-01

The objective of the Department of Defense Physical Security Equipment (DoD PSE) RDT&E program is to provide end users within the four Services with the most efficient and productive physical security (PS) at the most reasonable cost to ensure the effective protection of DoD resources. These resources include personnel, nuclear weapons, classified information, materiel, and readiness assets. As a result of the1996 Khobar Towers terrorist bombing incident, the DoD PSE program began to receive additional funding in 1997 for Force Protection Commercial-Off-The-Shelf (FP COTS) equipment evaluation and testing. The FP COTS testing applies to all available technologies, which are considered effective for DoD use. Successive terrorist incidents occurring since Khobar Towers have resulted in increasing focus on the demonstration and validation of equipment necessary to combat the ubiquitously asymmetric terrorist threat.

TOPEX satellite concept. TOPEX option study report

NASA Technical Reports Server (NTRS)

Meyer, D. P.; Case, C. M.

1982-01-01

Candidate bus equipment from the Viking, Applications Explorer Mission, and Small Scientific Satellite programs for application to the TOPEX mission options is assessed. Propulsion module equipment and subsystem candidates from the Applications Explorer Mission satellites and the Small Scientific Satellite spacecraft are evaluated for those TOPEX options. Several subsystem concepts appropriate to the TOPEX options are described. These descriptions consider performance characteristics of the subsystems. Cost and availability information on the candidate equipment and subsystems are also provided.

Emissions performance of abatement technologies over the proposed EEC extra-urban driving cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

VanBeckhoven, L.C.; Rijkeboer, R.C.

1989-01-01

The definition of what is likely to be the new EEC extra-urban cycle has made it possible to determine the emission characteristics of cars fitted with different emissions control equipment. Central to the evaluation program were three versions of experimental lean and dilute burn engines compared with engine modifications and open and closed loop three-way catalyst systems. This paper describes the evaluation program and evaluates its results.

PREPARACION, PROGRESO, PORVENIR (PREPARATION FOR PROGRESS TO THE FUTURE).

ERIC Educational Resources Information Center

CALLEJO, RICARDO A.; STOUFFER, CLAYTON L.

THE OBJECTIVES OF THIS PILOT PROGRAM WERE TO (1) MOTIVATE DISADVANTAGED SPANISH-SURNAMED YOUTH TO ENTER EXISTING VOCATIONAL TRAINING PROGRAMS THROUGH THE USE OF NEW TELEVISION TECHNIQUES AND EQUIPMENT IN SAN FRANCISCO AND SAN JOSE, AND (2) DEVELOP A COMPREHENSIVE EVALUATION DESIGN WHICH WOULD RESULT IN A PROGRAM DEVELOPMENT HANDBOOK AND AN EXAMPLE…

FIELD ANALYTICAL SCREENING PROGRAM: PCP METHOD - INNOVATIVE TECHNOLOGY EVALUATION REPORT

EPA Science Inventory

The Field Analytical Screening Program (FASP) pentachlorophenol (PCP) method uses a gas chromatograph (GC) equipped with a megabore capillary column and flame ionization detector (FID) and electron capture detector (ECD) to identify and quantify PCP. The FASP PCP method is design...

The Crescent Project : an evaluation of an element of the HELP Program : executive summary

DOT National Transportation Integrated Search

1994-02-01

The HELP/Crescent Project on the West Coast evaluated the applicability of four technologies for screening transponder-equipped vehicles. The technologies included automatic vehicle identification, weigh-in-motion, automatic vehicle classification, a...

Evaluation of Title I Program, Community School Distrlct 31, New York City. 1978-79 School Year. Final Report, E.D.L. Reading Lab.

ERIC Educational Resources Information Center

Knight, Michael E.

This program was designed to improve reading skills and to provide intensive remediation for students in grades six through nine. Specialized materials and equipment were provided by Educational Development Laboratories (EDL). The EDL Reading Laboratory utilized the Learning 100 program, a multi-modality developmental and remedial program. Small…

Equipment upgrades for the Pu-238 program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J.W.; Stephens, W.D.; Marra, J.E.

1990-02-14

Much of the equipment and instrumentation in the Pu-238 production facilities is more than 15 years old. Significant improvements have been made in the available instrumentation, in particular, due to the application of microprocessors and lasers. The Actinide Technology Section of SRL has selected and is in the process of evaluating several state-of-the-art instruments which have potential applications in the Pu-238 program. The ease of operation and the accuracy of the instruments have been improved and, in most cases, the cost of the instruments have decreased. 5 refs.

Dispensing Equipment Testing with Mid-Level Ethanol/Gasoline Test Fluid: Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyce, K.; Chapin, J. T.

The National Renewable Energy Laboratory's (NREL) Nonpetroleum-Based Fuel Task addresses the hurdles to commercialization of biomass-derived fuels and fuel blends. One such hurdle is the unknown compatibility of new fuels with current infrastructure, such as the equipment used at service stations to dispense fuel into automobiles. The U.S. Department of Energy's (DOE) Vehicle Technology Program and the Biomass Program have engaged in a joint project to evaluate the potential for blending ethanol into gasoline at levels higher than nominal 10 volume percent. This project was established to help DOE and NREL better understand any potentially adverse impacts caused by amore » lack of knowledge about the compatibility of the dispensing equipment with ethanol blends higher than what the equipment was designed to dispense. This report provides data about the impact of introducing a gasoline with a higher volumetric ethanol content into service station dispensing equipment from a safety and a performance perspective.« less

29 CFR 1960.56 - Training of safety and health specialists.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., laboratory experiences, field study, and other formal learning experiences to prepare them to perform the... program development and implementation, as well as hazard recognition, evaluation and control, equipment... tasks. (b) Each agency shall implement career development programs for their occupational safety and...

Ethnographic Techniques in Educational Evaluation: An Illustration.

ERIC Educational Resources Information Center

Fetterman, David

1980-01-01

Describes the ethnographic component of a multidisciplinary evaluation, conducted by the RMC Research Corporation, of the Career Intern Program for dropouts. Includes discussion of participant observations, interviewing techniques, triangulation, unobtrusive measures, data recording, and equipment. (Part of a theme issue entitled…

Injection of Contaminants into a Simulated Water Distribution System Equipped with Continuous Multi-Parameter Water Monitors

EPA Science Inventory

The U.S. EPA’s Technology Testing and Evaluation Program has been charged by EPA to evaluate the performance of commercially available water security-related technologies. Multi-parameter water monitors for distributions systems have been evaluated as such a water security techn...

Use of personal protective equipment for respiratory protection.

PubMed

Sargent, Edward V; Gallo, Frank

2003-01-01

Management of hazards in biomedical research facilities requires the application of the traditional industrial hygiene responsibilities of anticipation, recognition, evaluation, and control to characterize the work environment, evaluate tasks and equipment, identify hazards, define exposure groups, and recommend controls. Generally, the diversity and unique characteristics of hazards faced by laboratory and animal facility employees and the short-term and low-level nature of the exposures factor into the selection of proper exposure control measures in the laboratory. The proper selection of control measures is based on a hierarchy of elimination and minimization by engineering controls, followed last by personal protective equipment when exposures cannot be eliminated. Once it is decided that personal protective equipment is needed, specific regulations and guidelines define safety standards for research facilities, including the elements of a sound respiratory protection program. These elements include respirator selection (including appropriate protection factors), medical evaluation, fit testing, training, inspection, maintenance and care, quality, quantity and flow of breathing air, and routine and emergency use procedures.

Project FIRES. Volume 1: Program Overview and Summary, Phase 1B

NASA Technical Reports Server (NTRS)

Abeles, F. J.

1980-01-01

Overall performance requirements and evaluation methods for firefighters protective equipment were established and published as the Protective Ensemble Performance Standards (PEPS). Current firefighters protective equipment was tested and evaluated against the PEPS requirements, and the preliminary design of a prototype protective ensemble was performed. In phase 1B, the design of the prototype ensemble was finalized. Prototype ensembles were fabricated and then subjected to a series of qualification tests which were based upon the PEPS requirements. Engineering drawings and purchase specifications were prepared for the new protective ensemble.

Federal Aviation Administration aging aircraft nondestructive inspection research plan

NASA Technical Reports Server (NTRS)

Seher, Chris C.

1992-01-01

This paper highlights the accomplishments and plans of the Federal Aviation Administration (FAA) for the development of improved nondestructive evaluation (NDE) equipment, procedures, and training. The role of NDE in aircraft safety and the need for improvement are discussed. The FAA program participants, and coordination of activities within the program and with relevant organizations outside the program are also described.

SLOPE STABILITY EVALUATION AND EQUIPMENT SETBACK DISTANCES FOR BURIAL GROUND EXCAVATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

MCSHANE DS

2010-03-25

After 1970 Transuranic (TRU) and suspect TRU waste was buried in the ground with the intention that at some later date the waste would be retrieved and processed into a configuration for long term storage. To retrieve this waste the soil must be removed (excavated). Sloping the bank of the excavation is the method used to keep the excavation from collapsing and to provide protection for workers retrieving the waste. The purpose of this paper is to document the minimum distance (setback) that equipment must stay from the edge of the excavation to maintain a stable slope. This evaluation examinesmore » the equipment setback distance by dividing the equipment into two categories, (1) equipment used for excavation and (2) equipment used for retrieval. The section on excavation equipment will also discuss techniques used for excavation including the process of benching. Calculations 122633-C-004, 'Slope Stability Analysis' (Attachment A), and 300013-C-001, 'Crane Stability Analysis' (Attachment B), have been prepared to support this evaluation. As shown in the calculations the soil has the following properties: Unit weight 110 pounds per cubic foot; and Friction Angle (natural angle of repose) 38{sup o} or 1.28 horizontal to 1 vertical. Setback distances are measured from the top edge of the slope to the wheels/tracks of the vehicles and heavy equipment being utilized. The computer program utilized in the calculation uses the center of the wheel or track load for the analysis and this difference is accounted for in this evaluation.« less

Design of a medical and laboratory equipment management program for the new standards certification achievement in Mexico.

PubMed

Franco-Clark, D; Pimentel-Aguilar, A B; Rodriguez-Vera, R

2010-01-01

Certification for healthcare institutions in Mexico is ruled by 2009 standards homologated with the Joint Commission International criteria. Nowadays, healthcare requires of medical equipment and devices, so it has become necessary to implement guidelines for its adequate management in order to reach the highest level of quality and safety at the lowest cost. The objective of this work was to develop a Medical and Laboratory Equipment Management Program, oriented to the improvement of quality, effectiveness and efficiency of the technological resources in order to meet the certification requirements. The result of this work allows to have an auto evaluation tool that focuses the efforts of the National Institute for Respiratory Diseases to the achievement of the new requirements established for the certification.

Airside HVAC BESTEST. Adaptation of ASHRAE RP 865 Airside HVAC Equipment Modeling Test Cases for ASHRAE Standard 140. Volume 1, Cases AE101-AE445

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neymark, J.; Kennedy, M.; Judkoff, R.

This report documents a set of diagnostic analytical verification cases for testing the ability of whole building simulation software to model the air distribution side of typical heating, ventilating and air conditioning (HVAC) equipment. These cases complement the unitary equipment cases included in American National Standards Institute (ANSI)/American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) Standard 140, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs, which test the ability to model the heat-transfer fluid side of HVAC equipment.

Assessment of the current status of playground safety in the midwestern region of Turkey: an effort to provide a safe environment for children.

PubMed

Uskun, Ersin; Kişioğlu, Ahmet Nesimi; Altay, Tülin; Cikinlar, Rengül; Kocakaya, Asuman

2008-01-01

This study aimed to identify and evaluate the degree of conformity to the playground standards and the level of compliance with current safety specifications of the playgrounds in the midwestern region of Turkey. An observational technique was used at a total of 57 public playgrounds. A playground safety control form was prepared based on the United States National Program for Playground Safety and the Consumer Product Safety Commission security standards, since there is no national law covering playground equipment and safety in Turkey. The study evaluated the surroundings of the playground, arrangement of equipment in the playground, and characteristics of the equipment. The percentage of playgrounds surveyed with inadequate or hard surfacing was 80.7%. Fifty-two percent of the equipment was found to be inappropriate. Equipment was higher than the recommended heights. The results of our study unfortunately point out that playgrounds for children do not meet many of the safety criteria.

Electrical, Electronic, and Electromechanical (EEE) parts management and control requirements for NASA space flight programs

NASA Technical Reports Server (NTRS)

1989-01-01

This document establishes electrical, electronic, and electromechanical (EEE) parts management and control requirements for contractors providing and maintaining space flight and mission-essential or critical ground support equipment for NASA space flight programs. Although the text is worded 'the contractor shall,' the requirements are also to be used by NASA Headquarters and field installations for developing program/project parts management and control requirements for in-house and contracted efforts. This document places increased emphasis on parts programs to ensure that reliability and quality are considered through adequate consideration of the selection, control, and application of parts. It is the intent of this document to identify disciplines that can be implemented to obtain reliable parts which meet mission needs. The parts management and control requirements described in this document are to be selectively applied, based on equipment class and mission needs. Individual equipment needs should be evaluated to determine the extent to which each requirement should be implemented on a procurement. Utilization of this document does not preclude the usage of other documents. The entire process of developing and implementing requirements is referred to as 'tailoring' the program for a specific project. Some factors that should be considered in this tailoring process include program phase, equipment category and criticality, equipment complexity, and mission requirements. Parts management and control requirements advocated by this document directly support the concept of 'reliability by design' and are an integral part of system reliability and maintainability. Achieving the required availability and mission success objectives during operation depends on the attention given reliability and maintainability in the design phase. Consequently, it is intended that the requirements described in this document are consistent with those of NASA publications, 'Reliability Program Requirements for Aeronautical and Space System Contractors,' NHB 5300.4(1A-l); 'Maintainability Program Requirements for Space Systems,' NHB 5300.4(1E); and 'Quality Program Provisions for Aeronautical and Space System Contractors,' NHB 5300.4(1B).

A typewriting system operated by head movements, based on home-computer equipment.

PubMed

Heuvelmans, A M; Mélotte, H E; Neve, J J

1990-06-01

For persons who cannot move their hands and legs we have designed a relatively inexpensive typewriting system which can be operated by movements of the head. The typewriter is made up of commercially available home computer equipment - i e, a computer including monitor and printer and a headset replacing the mouse. A user-friendly software program has been designed to replace the mouse button and to make this equipment act as a typewriter with simple text-editing features. Some ergonomics aspects of the typewriter set-up and the results of an evaluation of the typewriter by two patients suffering from amyotrophic lateral sclerosis (ALS) are given. Several factors relevant to the design, construction, evaluation and application of the typewriter are discussed.

Permanent and separable aerospace tubing/ fitting evaluation program, volume 1

NASA Technical Reports Server (NTRS)

Ursell, C. R.; Franz, C. R.

1975-01-01

The tube fitting evaluation program was conducted to develop a standard overall test program including methods, procedures, and equipment as well as recommended test sequences for qualifying fitting/tubing assemblies. The program consisted of testing the MS flareless (separable) fitting and utilizing the results as baseline data from which all other fittings will be evaluated. Five separable designs and five permanent designs were tested in three sizes with two types of tubing materials. The basic design requirements were 4,000 psi operating pressure within the temperature range of minus 65 F to plus 450 F while also being compatible with 21-6-9 and titanium 3Al-2.5V tubing alloys.

Puerto Rico's PLATO Learning Program: An Independent Evaluation of the PLATO Learning Model

ERIC Educational Resources Information Center

Shillady, Lucinda; Miller, Libbie

2004-01-01

The Comprehensive School Reform (CSR) program has become a valuable resource in the implementation of the Puerto Rico Department of Education's educational reform process. To support the process, the Commonwealth of Puerto Rico granted computerized equipment, reading and mathematics software and training designed for schools. This included reading…

Software Tools: A One-Semester Secondary School Computer Course.

ERIC Educational Resources Information Center

Bromley, John; Lakatos, John

1985-01-01

Provides a course outline, describes equipment and teacher requirements, discusses student evaluation and course outcomes, and details the computer programs used in a high school course. The course is designed to teach students use of the microcomputer as a tool through hands-on experience with a variety of commercial software programs. (MBR)

Evaluating the Relevance of the Chemistry Curriculum to the Workplace: Keeping Tertiary Education Relevant

ERIC Educational Resources Information Center

Yasin, Nur Yaisyah Bte Md; Yueying, Ong

2017-01-01

There are various programs and initiatives in universities that aim to maximize students' potential in their academic journey, personal life, and future career. Research opportunities, internships, overseas exchange programs, and other initiatives aim to equip students with the hard and soft skills needed by employers. Although these efforts are…

Skylab astronaut life support assembly

NASA Technical Reports Server (NTRS)

Brown, J. T.

1972-01-01

A comparative study was performed to define an optimum portable life support system for suited operations inside and outside the Skylab Program. Emphasis was placed on utilization of qualified equipment, modified versions of qualified equipment, and new systems made up to state-of-the-art components. Outlined are the mission constraints, operational modes, and evaluation ground rules by which the Skylab portable life support system was selected and the resulting design.

Evaluation of a disposable diesel exhaust filter for permissible mining machines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ambs, J.L.; Cantrell, B.K.; Watts, W.F.

1994-01-01

The US Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mines using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterbath exhaust conditioners. These were evaluated in three underground mines to determine their effectiveness inmore » reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90% at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.« less

EDCATS: An Evaluation Tool

NASA Technical Reports Server (NTRS)

Heard, Pamala D.

1998-01-01

The purpose of this research is to explore the development of Marshall Space Flight Center Unique Programs. These academic tools provide the Education Program Office with important information from the Education Computer Aided Tracking System (EDCATS). This system is equipped to provide on-line data entry, evaluation, analysis, and report generation, with full archiving for all phases of the evaluation process. Another purpose is to develop reports and data that is tailored to Marshall Space Flight Center Unique Programs. It also attempts to acquire knowledge on how, why, and where information is derived. As a result, a user will be better prepared to decide which available tool is the most feasible for their reports.

Object-Oriented Algorithm For Evaluation Of Fault Trees

NASA Technical Reports Server (NTRS)

Patterson-Hine, F. A.; Koen, B. V.

1992-01-01

Algorithm for direct evaluation of fault trees incorporates techniques of object-oriented programming. Reduces number of calls needed to solve trees with repeated events. Provides significantly improved software environment for such computations as quantitative analyses of safety and reliability of complicated systems of equipment (e.g., spacecraft or factories).

VI-G, Sec. 661, P.L. 91-230. Final Performance Report.

ERIC Educational Resources Information Center

1976

Presented is the final performance report of the CSDC model which is designed to provide services for learning disabled high school students. Sections cover the following program aspects: organizational structure, inservice sessions, identification of students, materials and equipment, evaluation of student performance, evaluation of the model,…

Structural Crashworthiness Standards Comparison: Grade Crossing Collision Scenarios

DOT National Transportation Integrated Search

2009-10-20

In support of the Federal Railroad Administrations (FRA) : Railroad Equipment Safety Program, American and European : grade-crossing collision scenarios were evaluated and : compared. Finite element analyses (FEA) were employed to : subject an FRA...

Cost analysis of oxygen recovery systems

NASA Technical Reports Server (NTRS)

Yakut, M. M.

1973-01-01

The design and development of equipment for flight use in earth-orbital programs, when optimally approached cost effectively, proceed through the following logical progression: (1) bench testing of breadboard designs, (2) the fabrication and evaluation of prototype equipment, (3) redesign to meet flight-imposed requirements, and (4) qualification and testing of a flight-ready system. Each of these steps is intended to produce the basic design information necessary to progress to the next step. The cost of each step is normally substantially less than that of the following step. An evaluation of the cost elements involved in each of the steps and their impact on total program cost are presented. Cost analyses of four leading oxygen recovery subsystems which include two carbon dioxide reduction subsystem, Sabatier and Bosch, and two water electrolysis subsystems, the solid polymer electrolyte and the circulating KOH electrolyte are described.

Airside HVAC BESTEST: HVAC Air-Distribution System Model Test Cases for ASHRAE Standard 140

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judkoff, Ronald; Neymark, Joel; Kennedy, Mike D.

This paper summarizes recent work to develop new airside HVAC equipment model analytical verification test cases for ANSI/ASHRAE Standard 140, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs. The analytical verification test method allows comparison of simulation results from a wide variety of building energy simulation programs with quasi-analytical solutions, further described below. Standard 140 is widely cited for evaluating software for use with performance-path energy efficiency analysis, in conjunction with well-known energy-efficiency standards including ASHRAE Standard 90.1, the International Energy Conservation Code, and other international standards. Airside HVAC Equipment is a common area ofmore » modelling not previously explicitly tested by Standard 140. Integration of the completed test suite into Standard 140 is in progress.« less

Aquatic Equipment Information.

ERIC Educational Resources Information Center

Sova, Ruth

Equipment usually used in water exercise programs is designed for variety, intensity, and program necessity. This guide discusses aquatic equipment under the following headings: (1) equipment design; (2) equipment principles; (3) precautions and contraindications; (4) population contraindications; and (5) choosing equipment. Equipment is used…

Limited economic evaluation to assess the effectiveness of a university-wide office ergonomics program.

PubMed

Bidassie, Balmatee; McGlothlin, James D; Goh, Alina; Feyen, Robert G; Barany, James W

2010-05-01

The objective of this research was to evaluate the effectiveness and provide a limited economic evaluation of an office ergonomics program at a major university from 1995 to 2007. The relationship between office-related recordable injuries, reported lost time, severity of these injuries, and the Workers' Compensation (WC) paid was analyzed and the corresponding incident cost was calculated. Two major datasets analyzed were OSHA 200/300 logs (1991-2007) and WC claims paid (1999-2007). Since the beginning of the office ergonomics program in 1995 and through 2007 (13-year period), the number of office cumulative trauma disorder (CTD) cases decreased by 53%. Since the official start (in 1999) of a 50-50 cost share agreement for office equipment purchases between the university's Safety and Health Department (SHD) and the university departments evaluated, it was observed that the incident rate decreased by 63%, Total Days Away/restrict or Transfer (DART) rate decreased by 41%, Lost Time Case (LTC) rate decreased by 71% and office-related carpal tunnel syndrome decreased by almost 50%. The long-term goal of this research is to demonstrate the self-sustainability of an office ergonomics program by showing that equipment costs are eventually offset by a decrease in WC claims paid and lost time from office-related injuries and illnesses. While limited, this research helps in cost-justifying the implementation of future office ergonomics programs for large organizations. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Materials research for high-speed civil transport and generic hypersonics: Composites durability

NASA Technical Reports Server (NTRS)

Allen-Lilly, Heather; Cregger, Eric; Hoffman, Daniel; Mccool, Jim

1995-01-01

This report covers a portion of an ongoing investigation of the durability of composites for the High Speed Civil Transport (HSCT) program. Candidate HSCT composites need to possess the high-temperature capability required for supersonic flight. This program was designed to initiate the design, analysis, fabrication, and testing of equipment intended for use in validating the long-term durability of materials for the HSCT. This equipment includes thermally actuated compression and tension fixtures, hydraulic-actuated reversible load fixtures, and thermal chambers. This equipment can be used for the durability evaluation of both composite and adhesive materials. Thermally actuated fixtures are recommended for fatigue cycling when long-term thermomechanical fatigue (TMF) data are required on coupon-sized tension or compression specimens. Long term durability testing plans for polymer matrix composite specimens are included.

Braking and cornering studies on an air cushion landing system

NASA Technical Reports Server (NTRS)

Daugherty, R. H.

1983-01-01

An experimental investigation was conducted to evaluate several concepts for braking and steering a vehicle equipped with an air cushion landing system (ACLS). The investigation made use of a modified airboat equipped with an ACLS. Braking concepts were characterized by the average deceleration of the vehicle. Reduced lobe flow and cavity venting braking concepts were evaluated in this program. The cavity venting braking concept demonstrated the best performance, producing decelerations on the test vehicle on the same order as moderate braking with conventional wheel brakes. Steering concepts were evaluated by recording the path taken while attempting to follow a prescribed maneuver. The steering concepts evaluated included using rudders only, using differential lobe flow, and using rudders combined with a lightly loaded, nonsteering center wheel. The latter concept proved to be the most accurate means of steering the vehicle on the ACLS, producing translational deviations two to three times higher than those from conventional nose-gear steering. However, this concept was still felt to provide reasonably precise steering control for the ACLS-equipped vehicle.

SU-F-T-226: QA Management for a Large Institution with Multiple Campuses for FMEA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, G; Chan, M; Lovelock, D

2016-06-15

Purpose: To redesign our radiation therapy QA program with the goal to improve quality, efficiency, and consistency among a growing number of campuses at a large institution. Methods: A QA committee was established with at least one physicist representing each of our six campuses (22 linacs). Weekly meetings were scheduled to advise on and update current procedures, to review end-to-end and other test results, and to prepare composite reports for internal and external audits. QA procedures for treatment and imaging equipment were derived from TG Reports 142 and 66, practice guidelines, and feedback from ACR evaluations. The committee focused onmore » reaching a consensus on a single QA program among all campuses using the same type of equipment and reference data. Since the recommendations for tolerances referenced to baseline data were subject to interpretation in some instances, the committee reviewed the characteristics of all machines and quantified any variations before choosing between treatment planning system (i.e. treatment planning system commissioning data that is representative for all machines) or machine-specific values (i.e. commissioning data of the individual machines) as baseline data. Results: The configured QA program will be followed strictly by all campuses. Inventory of available equipment has been compiled, and additional equipment acquisitions for the QA program are made as needed. Dosimetric characteristics are evaluated for all machines using the same methods to ensure consistency of beam data where possible. In most cases, baseline data refer to treatment planning system commissioning data but machine-specific values are used as reference where it is deemed appropriate. Conclusion: With a uniform QA scheme, variations in QA procedures are kept to a minimum. With a centralized database, data collection and analysis are simplified. This program will facilitate uniformity in patient treatments and analysis of large amounts of QA data campus-wide, which will ultimately facilitate FMEA.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mundy, D; Tryggestad, E; Beltran, C

Purpose: To develop daily and monthly quality assurance (QA) programs in support of a new spot-scanning proton treatment facility using a combination of commercial and custom equipment and software. Emphasis was placed on efficiency and evaluation of key quality parameters. Methods: The daily QA program was developed to test output, spot size and position, proton beam energy, and image guidance using the Sun Nuclear Corporation rf-DQA™3 device and Atlas QA software. The program utilizes standard Atlas linear accelerator tests repurposed for proton measurements and a custom jig for indexing the device to the treatment couch. The monthly QA program wasmore » designed to test mechanical performance, image quality, radiation quality, isocenter coincidence, and safety features. Many of these tests are similar to linear accelerator QA counterparts, but many require customized test design and equipment. Coincidence of imaging, laser marker, mechanical, and radiation isocenters, for instance, is verified using a custom film-based device devised and manufactured at our facility. Proton spot size and position as a function of energy are verified using a custom spot pattern incident on film and analysis software developed in-house. More details concerning the equipment and software developed for monthly QA are included in the supporting document. Thresholds for daily and monthly tests were established via perturbation analysis, early experience, and/or proton system specifications and associated acceptance test results. Results: The periodic QA program described here has been in effect for approximately 9 months and has proven efficient and sensitive to sub-clinical variations in treatment delivery characteristics. Conclusion: Tools and professional guidelines for periodic proton system QA are not as well developed as their photon and electron counterparts. The program described here efficiently evaluates key quality parameters and, while specific to the needs of our facility, could be readily adapted to other proton centers.« less

40 CFR 1068.110 - What other provisions apply to engines/equipment in service?

Code of Federal Regulations, 2013 CFR

2013-07-01

... information regarding test programs, engineering evaluations, design specifications, calibrations, on-board computer algorithms, and design strategies. It is a violation of the Clean Air Act for anyone to make...

40 CFR 1068.110 - What other provisions apply to engines/equipment in service?

Code of Federal Regulations, 2014 CFR

2014-07-01

... information regarding test programs, engineering evaluations, design specifications, calibrations, on-board computer algorithms, and design strategies. It is a violation of the Clean Air Act for anyone to make...

40 CFR 1068.110 - What other provisions apply to engines/equipment in service?

Code of Federal Regulations, 2012 CFR

2012-07-01

... information regarding test programs, engineering evaluations, design specifications, calibrations, on-board computer algorithms, and design strategies. It is a violation of the Clean Air Act for anyone to make...

Definition of Life Sciences laboratories for shuttle/Spacelab. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1975-01-01

Research requirements and the laboratories needed to support a Life Sciences research program during the shuttle/Spacelab era were investigated. A common operational research equipment inventory was developed to support a comprehensive but flexible Life Sciences program. Candidate laboratories and operational schedules were defined and evaluated in terms of accomodation with the Spacelab and overall program planning. Results provide a firm foundation for the initiation of a life science program for the shuttle era.

Apollo experience report: Very high frequency ranging system

NASA Technical Reports Server (NTRS)

Panter, W. C.; Shores, P. W.

1972-01-01

The history of the Apollo very-high-frequency ranging system development program is presented from the program-planning stage through the final-test and flight-evaluation stages. Block diagrams of the equipment are presented, and a description of the theory of operation is outlined. A sample of the distribution of errors measured in the aircraft-flight test program is included. The report is concluded with guidelines or recommendations for the management of development programs having the same general constraints.

CIVIL TECHNOLOGY, HIGHWAY AND STRUCTURAL OPTIONS, A SUGGESTED 2-YEAR POST HIGH SCHOOL CURRICULUM. TECHNICAL EDUCATION PROGRAM SERIES, NUMBER 8.

ERIC Educational Resources Information Center

BEAUMONT, JOHN A; AND OTHERS

DESIGNED TO ASSIST ADMINISTRATORS, SUPERVISORS, AND TEACHERS TO PLAN, DEVELOP, AND EVALUATE PROGRAMS, THIS CURRICULUM GUIDE OFFERS COURSE OUTLINES, PROCEDURES, LABORATORY LAYOUTS, TEXTS AND REFERENCES, LISTS OF LABORATORY EQUIPMENT AND ITS COST, AND A SELECTED LIST OF SCIENTIFIC AND TECHNICAL SOCIETIES. BASIC MATERIALS WERE PREPARED AT THE…

An Evaluation of Perceptions of Form, Fit, Function (F3) Standardization on the Standard Inertial Navigation Unit (STD INU) Program.

DTIC Science & Technology

1987-12-01

support durring the first few years of operations, which provides an incentive for such innovations and defers the acquisition of AGE until the equipment...along with number of standard avionics programs worked and the ranks of each individual. Table 5. Expierence With Avionics Standardization Years

Evaluating complex health financing interventions: using mixed methods to inform further implementation of a novel PBI intervention in rural Malawi.

PubMed

McMahon, Shannon A; Brenner, Stephan; Lohmann, Julia; Makwero, Christopher; Torbica, Aleksandra; Mathanga, Don P; Muula, Adamson S; De Allegri, Manuela

2016-08-19

Gaps remain in understanding how performance-based incentive (PBI) programs affect quality of care and service quantity, whether programs are cost effective and how programs could be tailored to meet client and provider needs while remaining operationally viable. In 2014, Malawi's Ministry of Health launched the Service Delivery Integration-PBI (SSDI-PBI) program. The program is unique in that no portion of performance bonuses are paid to individual health workers, and it shifts responsibility for infrastructure and equipment procurement from facility staff to implementing partners. This protocol outlines an approach that analyzes processes and outcomes, considers expected and unexpected consequences of the program and frames the program's outputs relative to its costs. Findings from this evaluation will inform the intended future scale-up of PBI in Malawi. This study employs a prospective controlled before-and-after triangulation design to assess effects of the PBI program by analyzing quantitative and qualitative data from intervention and control facilities. Guided by a theoretical framework, the evaluation consists of four main components: service provision, health worker motivation, implementation processes and costing. Quality and access outcomes are assessed along four dimensions: (1) structural elements (related to equipment, drugs, staff); (2) process elements (providers' compliance with standards); (3) outputs (service utilization); (4) experiential elements (experiences of service delivery). The costing component includes costs related to start-up, ongoing management, and the cost of incentives themselves. The cost analysis considers costs incurred within the Ministry of Health, funders, and the implementing agency. The evaluation relies on primary data (including interviews and surveys) and secondary data (including costing and health management information system data). Through the lens of a PBI program, we illustrate how complex interventions can be evaluated via not only primary, mixed-methods data collection, but also through a wealth of secondary data from program implementers (including monitoring, evaluation and financial data), and the health system (including service utilization and service readiness data). We also highlight the importance of crafting a theory and using theory to inform the nature of data collected. Finally, we highlight the need to be responsive to stakeholders in order to enhance a study's relevance.

Furniture rough mill costs evaluated by computer simulation

Treesearch

R. Bruce Anderson

1983-01-01

A crosscut-first furniture rough mill was simulated to evaluate processing and raw material costs on an individual part basis. Distributions representing the real-world characteristics of lumber, equipment feed speeds, and processing requirements are programed into the simulation. Costs of parts from a specific cutting bill are given, and effects of lumber input costs...

76 FR 24060 - Proposed Extension of Existing Information Collection; Testing, Evaluation, and Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-29

... Extension of Existing Information Collection; Testing, Evaluation, and Approval of Mining Products AGENCY... Reduction Act of 1995 [44 U.S.C. 3506(c)(2)(A)]. This program helps to ensure that requested data can be..., testing, approval and certification, and quality control of mining equipment and components, materials...

Modifications of ORNL's computer programs MSF-21 and VTE-21 for the evaluation and rapid optimization of multistage flash and vertical tube evaporators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glueckstern, P.; Wilson, J.V.; Reed, S.A.

1976-06-01

Design and cost modifications were made to ORNL's Computer Programs MSF-21 and VTE-21 originally developed for the rapid calculation and design optimization of multistage flash (MSF) and multieffect vertical tube evaporator (VTE) desalination plants. The modifications include additional design options to make possible the evaluation of desalting plants based on current technology (the original programs were based on conceptual designs applying advanced and not yet proven technological developments and design features) and new materials and equipment costs updated to mid-1975.

45 CFR 95.707 - Equipment management and disposition.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 1 2011-10-01 2011-10-01 false Equipment management and disposition. 95.707... ADMINISTRATION-GRANT PROGRAMS (PUBLIC ASSISTANCE, MEDICAL ASSISTANCE AND STATE CHILDREN'S HEALTH INSURANCE PROGRAMS) Equipment Acquired Under Public Assistance Programs § 95.707 Equipment management and disposition...

45 CFR 95.707 - Equipment management and disposition.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Equipment management and disposition. 95.707... ADMINISTRATION-GRANT PROGRAMS (PUBLIC ASSISTANCE, MEDICAL ASSISTANCE AND STATE CHILDREN'S HEALTH INSURANCE PROGRAMS) Equipment Acquired Under Public Assistance Programs § 95.707 Equipment management and disposition...

Medical technology management: from planning to application.

PubMed

David, Y; Jahnke, E

2005-01-01

Appropriate deployment of technological innovation contributes to improvement in the quality of healthcare delivered, the containment of cost, and access to the healthcare system. Hospitals have been allocating a significant portion of their resources to procuring and managing capital assets; they are continuously faced with demands for new medical equipment and are asked to manage existing inventory for which they are not well prepared. To objectively manage their investment, hospitals are developing medical technology management programs that need pertinent information and planning methodology for integrating new equipment into existing operations as well as for optimizing costs of ownership of all equipment. Clinical engineers can identify technological solutions based on the matching of new medical equipment with hospital's objectives. They can review their institution's overall technological position, determine strengths and weaknesses, develop equipment-selection criteria, supervise installations, train users and monitor post procurement performance to assure meeting of goals. This program, together with cost accounting analysis, will objectively guide the capital assets decision-making process. Cost accounting analysis is a multivariate function that includes determining the amount, based upon a strategic plan and financial resources, of funding to be allocated annually for medical equipment acquisition and replacement. Often this function works closely with clinical engineering to establish equipment useful life and prioritization of acquisition, upgrade, and replacement of inventory within budget confines and without conducting time consuming, individual financial capital project evaluations.

Terminal configured vehicle program: Test facilities guide

NASA Technical Reports Server (NTRS)

1980-01-01

The terminal configured vehicle (TCV) program was established to conduct research and to develop and evaluate aircraft and flight management system technology concepts that will benefit conventional take off and landing operations in the terminal area. Emphasis is placed on the development of operating methods for the highly automated environment anticipated in the future. The program involves analyses, simulation, and flight experiments. Flight experiments are conducted using a modified Boeing 737 airplane equipped with highly flexible display and control equipment and an aft flight deck for research purposes. The experimental systems of the Boeing 737 are described including the flight control computer systems, the navigation/guidance system, the control and command panel, and the electronic display system. The ground based facilities used in the program are described including the visual motion simulator, the fixed base simulator, the verification and validation laboratory, and the radio frequency anechoic facility.

Emergency Preparedness and Response Systems

DTIC Science & Technology

2006-09-01

over time. Preparedness plans include program initiatives for planning, training, equipping, exercising, and evaluating capability to ensure sustainable ... performance in order to prevent, prepare for and respond to incidents. 4. Response Response refers to the activities necessary to address the

E-ZPass evaluation report

DOT National Transportation Integrated Search

2000-08-01

The implementation of electronic toll collection equipment on the New York State Thruway occurred over a four-year period beginning in the 1993 and ending in 1997. In conjunction with implementation program, the Authority set a list of goals and obje...

Adventure Education: What's the Law?

ERIC Educational Resources Information Center

Ewert, Alan

1981-01-01

Outdoor instructors should know legal considerations including inherent dangers, program objectives, participant awareness, participant evaluation, supervision, professional conduct, safety considerations, and negligence. Threats of law suits can be diminished with care, "foreseeability," appropriate techniques and equipment, and well-prepared…

Laboratory services series: a programmed maintenance system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuxbury, D.C.; Srite, B.E.

1980-01-01

The diverse facilities, operations and equipment at a major national research and development laboratory require a systematic, analytical approach to operating equipment maintenance. A computer-scheduled preventive maintenance program is described including program development, equipment identification, maintenance and inspection instructions, scheduling, personnel, and equipment history.

[A design of software for management of hospital equipment maintenance process].

PubMed

Xie, Haiyuan; Liu, Yiqing

2010-03-01

According to the circumstance of hospital equipment maintenance, we designed a computer program for management of hospital equipment maintenance process by Java programming language. This program can control the maintenance process, increase the efficiency; and be able to fix the equipment location.

Shuttle free-flying teleoperator system experiment definition. Volume 3: program development requirements

NASA Technical Reports Server (NTRS)

1972-01-01

The planning data are presented for subsequent phases of free-flying teleoperator program (FFTO) and includes costs, schedules and supporting research and technology activities required to implement the free-flying teleoperator system and associated flight equipment. The purpose of the data presented is to provide NASA with the information needed to continue development of the FFTO and integrate it into the space shuttle program. The planning data describes three major program phases consisting of activities and events scheduled to effect integrated design, development, fabrication and operation of an FFTO system. Phase A, Concept Generation, represents a study effort directed toward generating and evaluating a number of feasible FFTO experiment system concepts. Phase B, Definition, will include preliminary design and supporting analysis of the FFTO, the shuttle based equipment and ground support equipment. Phase C/D, Design, Development and Operations will include detail design of the operational FFTO, its integration into the space shuttle, hardware fabrication and testing, delivery of flight hardware and support of flight operations. Emphasis is placed on the planning for Phases A and B since these studies will be implemented early in the development cycle. Phase C/D planning is more general and subject to refinement during the definition phase.

HEDL FACILITIES CATALOG 400 AREA

DOE Office of Scientific and Technical Information (OSTI.GOV)

MAYANCSIK BA

1987-03-01

The purpose of this project is to provide a sodium-cooled fast flux test reactor designed specifically for irradiation testing of fuels and materials and for long-term testing and evaluation of plant components and systems for the Liquid Metal Reactor (LMR) Program. The FFTF includes the reactor, heat removal equipment and structures, containment, core component handling and examination, instrumentation and control, and utilities and other essential services. The complex array of buildings and equipment are arranged around the Reactor Containment Building.

Description of Audio-Visual Recording Equipment and Method of Installation for Pilot Training.

ERIC Educational Resources Information Center

Neese, James A.

The Audio-Video Recorder System was developed to evaluate the effectiveness of in-flight audio/video recording as a pilot training technique for the U.S. Air Force Pilot Training Program. It will be used to gather background and performance data for an experimental program. A detailed description of the system is presented and construction and…

Evaluation of Professional Development in the Use of Arts-Integrated Activities with Mathematics Content: Findings about Program Implementation

ERIC Educational Resources Information Center

Ludwig, Meredith Jane; Mengli, Song; Kouyate-Tate, Akua; Cooper, Jennifer E.; Phillips, Lori; Greenbaum, Sarah

2014-01-01

In 2010, the Wolf Trap Foundation for the Performing Arts, Institute for Early Learning Through the Arts, was awarded an Arts in Education Model Development and Dissemination (AEMDD) grant to develop, implement, and disseminate a research-based program of professional development (PD) that equips prekindergarten and kindergarten teachers to infuse…

Antenna design and development for the microwave subsystem experiments for the terminal configured vehicle project

NASA Technical Reports Server (NTRS)

Becher, J.; Cohen, N.; Rublee, J.

1981-01-01

The feasibility of classifying an airport terminal area for multipath effects, i.e., fadeout potentials or limits of video resolution, is examined. Established transmission links in terminal areas were modeled for landing approaches and overflight patterns. A computer program to obtain signal strength based on a described flight path was written. The application of this model to evaluate the signal transmission obtained in an actual flight equipped with additional signal strength monitoring equipment is described. The actual and computed received signal are compared, and the feasibility of the computer simulation for predicting signal amplitude fluctuation is evaluated.

Design of a video system providing optimal visual information for controlling payload and experiment operations with television

NASA Technical Reports Server (NTRS)

1975-01-01

A program was conducted which included the design of a set of simplified simulation tasks, design of apparatus and breadboard TV equipment for task performance, and the implementation of a number of simulation tests. Performance measurements were made under controlled conditions and the results analyzed to permit evaluation of the relative merits (effectivity) of various TV systems. Burden factors were subsequently generated for each TV system to permit tradeoff evaluation of system characteristics against performance. For the general remote operation mission, the 2-view system is recommended. This system is characterized and the corresponding equipment specifications were generated.

78 FR 54197 - Energy Efficiency Program for Commercial and Industrial Equipment: Energy Conservation Standards...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-03

.... EERE-2013-BT-STD-0030] RIN 1904-AD01 Energy Efficiency Program for Commercial and Industrial Equipment... Certain Industrial Equipment,'' a program covering certain commercial and industrial equipment (hereafter... (AEMTCA), Public Law 112-210 (Dec. 18, 2012). EPCA covers many types of commercial and industrial...

Technology Demonstration Summary, Chemfix Solidification/Stabilization Process, Clackamas, Oregon

EPA Science Inventory

ChemfIx's* patented stabilization/solidification technology was demonstrated at the Portable Equipment Salvage Company (PESC) site in Clackamas, Oregon, as part of the Superfund Innovative Technology Evaluation (SITE) program. The Chemfix process is designed to solidify and sta...

Best practices and strategies for improving rail energy efficiency

DOT National Transportation Integrated Search

2014-01-28

In support of the FRA Energy, Environment, and Engine (E3) program, this study reviews and evaluates technology development opportunities, equipment upgrades, and best practices (BPs) of international and U.S. passenger and freight rail industry segm...

Geosynchronous platform definition study. Volume 6: Geosynchronous program evaluation and recommendations

NASA Technical Reports Server (NTRS)

Myers, H. L.

1973-01-01

The programmatic analyses conducted to achieve the objectives of the study are presented. The characteristics are examined of alternate geosynchronous programs based on servicing concepts, geosynchronous platform configurations, and equipment definitions which have evolved during the study. The logistics support necessary to carry out programs using these systems is defined considering alternate approaches for on-orbit servicing. The costs of the resultant programs are then determined and the alternate program approaches compared. Conventional programs with expendable satellites are also defined to the extent necessary to permit comparison with on-orbit serviced platform programs.

Developing a Simulation-Based Training Program for the Prehospital Professionals and Students on the Management of Middle East Respiratory Syndrome.

PubMed

Elcin, Melih; Onan, Arif; Odabasi, Orhan; Saylam, Melahat; Ilhan, Handan; Daylan Kockaya, Pinar; Gurcuoglu, Ilker; Uckuyu, Yavuz; Cengiz, Duygu; Nacar, Osman Arikan

2016-12-01

Middle East Respiratory Syndrome (MERS) is a major global health threat. Prehospital professionals face the risk of infection as they work to save lives. They should be made aware of the disease and be prepared to handle such cases. The aims of our study are to develop a training program about the prehospital management of a MERS case using standardized patient (SP) scenarios, to evaluate the awareness and preparedness of the participants about MERS, and to evaluate the effectiveness of this training. We developed 5 scenarios using SPs and an observation form. We included paramedic students and emergency medical service (EMS) providers in our study. They were involved in the simulations. A total of 24 paramedic students and 33 EMS providers participated in our study. Sixteen (84%) of 19 teams recognized the possibility of MERS as a measure of their awareness in the baseline evaluation. The participants lacked donning and doffing personal protective equipments, which revealed their baseline level of preparedness for MERS. Certain improvements in donning and doffing personal protective equipment were observed in the posttraining evaluation. The participants provided positive feedback on the training program. The training program was appropriate for both paramedic students and EMS providers. A positive educational climate was created. Because the main concerns of this study were awareness and preparedness, which required human interaction, the SP methodology was the optimal simulation modality.

An Experimental Evaluation of Stress-Management Training for the Airborne Soldier. Technical Report 550.

ERIC Educational Resources Information Center

Burke, William P.

A project was conducted to evaluate the effectiveness of the stress-management training given to students in the jumpmaster training course at Fort Benning, Georgia. The course, which trains airborne personnel to conduct landings of men and equipment, features relatively stressful training programs during which instructors grade the performance of…

Effect of a Smart Start Playground Improvement Grant on Child Care Playground Hazards. Smart Start Evaluation Report.

ERIC Educational Resources Information Center

Kotch, Jonathan; Guthrie, Christine

Smart Start (North Carolina) playground improvement grants were awarded to cover playground safety assessment, planning and evaluation, quality enhancements (such as fencing, surfacing, and new equipment), and safety programs. Visual inspections were conducted of the safety of child care home and center playgrounds after Smart Start-sponsored…

Evaluation of the Redesign of an Undergraduate Cell Biology Course

ERIC Educational Resources Information Center

McEwen, Laura April; Harris, dik; Schmid, Richard F.; Vogel, Jackie; Western, Tamara; Harrison, Paul

2009-01-01

This article offers a case study of the evaluation of a redesigned and redeveloped laboratory-based cell biology course. The course was a compulsory element of the biology program, but the laboratory had become outdated and was inadequately equipped. With the support of a faculty-based teaching improvement project, the teaching team redesigned the…

Propulsion control experience used in the Highly Integrated Digital Electronic Control (HIDEC) program

NASA Technical Reports Server (NTRS)

Myers, L. P.; Burcham, F. W., Jr.

1984-01-01

The highly integrated digital electronic control (HIDEC) program will integrate the propulsion and flight control systems on an F-15 airplane at NASA Ames Research Center's Dryden Flight Research Facility. Ames-Dryden has conducted several propulsion control programs that have contributed to the HIDEC program. The digital electronic engine control (DEEC) flight evaluation investigated the performance and operability of the F100 engine equipped with a full-authority digital electronic control system. Investigations of nozzle instability, fault detection and accommodation, and augmentor transient capability provided important information for the HIDEC program. The F100 engine model derivative (EMD) was also flown in the F-15 airplane, and airplane performance was significantly improved. A throttle response problem was found and solved with a software fix to the control logic. For the HIDEC program, the F100 EMD engines equipped with DEEC controls will be integrated with the digital flight control system. The control modes to be implemented are an integrated flightpath management mode and an integrated adaptive engine control system mode. The engine control experience that will be used in the HIDEC program is discussed.

Evaluation of a disposable diesel exhaust filter for permissible mining machines. Report of investigations/1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ambs, J.L.; Cantrell, B.K.; Watts, W.F.

1994-01-01

The U.S. Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mining using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterban exhaust conditioners. These were evaluated in three underground mines to determine their effectiveness inmore » reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90 pct at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.« less

Transition Program for Equipment Manufacturers (TPEM)

EPA Pesticide Factsheets

In order to provide flexibility for small equipment manufacturers that must comply with new regulations, EPA created the Transition Program for Equipment Manufacturers, better known as “TPEM” or “flexibility program.”

Ongoing quality control in digital radiography: Report of AAPM Imaging Physics Committee Task Group 151.

PubMed

Jones, A Kyle; Heintz, Philip; Geiser, William; Goldman, Lee; Jerjian, Khachig; Martin, Melissa; Peck, Donald; Pfeiffer, Douglas; Ranger, Nicole; Yorkston, John

2015-11-01

Quality control (QC) in medical imaging is an ongoing process and not just a series of infrequent evaluations of medical imaging equipment. The QC process involves designing and implementing a QC program, collecting and analyzing data, investigating results that are outside the acceptance levels for the QC program, and taking corrective action to bring these results back to an acceptable level. The QC process involves key personnel in the imaging department, including the radiologist, radiologic technologist, and the qualified medical physicist (QMP). The QMP performs detailed equipment evaluations and helps with oversight of the QC program, the radiologic technologist is responsible for the day-to-day operation of the QC program. The continued need for ongoing QC in digital radiography has been highlighted in the scientific literature. The charge of this task group was to recommend consistency tests designed to be performed by a medical physicist or a radiologic technologist under the direction of a medical physicist to identify problems with an imaging system that need further evaluation by a medical physicist, including a fault tree to define actions that need to be taken when certain fault conditions are identified. The focus of this final report is the ongoing QC process, including rejected image analysis, exposure analysis, and artifact identification. These QC tasks are vital for the optimal operation of a department performing digital radiography.

Ongoing quality control in digital radiography: Report of AAPM Imaging Physics Committee Task Group 151

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, A. Kyle, E-mail: kyle.jones@mdanderson.org; Geiser, William; Heintz, Philip

Quality control (QC) in medical imaging is an ongoing process and not just a series of infrequent evaluations of medical imaging equipment. The QC process involves designing and implementing a QC program, collecting and analyzing data, investigating results that are outside the acceptance levels for the QC program, and taking corrective action to bring these results back to an acceptable level. The QC process involves key personnel in the imaging department, including the radiologist, radiologic technologist, and the qualified medical physicist (QMP). The QMP performs detailed equipment evaluations and helps with oversight of the QC program, the radiologic technologist ismore » responsible for the day-to-day operation of the QC program. The continued need for ongoing QC in digital radiography has been highlighted in the scientific literature. The charge of this task group was to recommend consistency tests designed to be performed by a medical physicist or a radiologic technologist under the direction of a medical physicist to identify problems with an imaging system that need further evaluation by a medical physicist, including a fault tree to define actions that need to be taken when certain fault conditions are identified. The focus of this final report is the ongoing QC process, including rejected image analysis, exposure analysis, and artifact identification. These QC tasks are vital for the optimal operation of a department performing digital radiography.« less

Department of the Air Force Supporting Data for Fiscal Year 1993 Budget Estimates Submitted to Congress January 1992 Descriptive Summaries. Research, Development, Test and Evaluation

DTIC Science & Technology

1992-01-01

Spacecraft Technology 0503401F 450 35 Space Systems Environmental Interactions Technology 060341 OF 468 36 Space Subsystems Technology 0603428F 472 37...Space Systems Environmental Interactions Technology 35 468 0603402F Space Test Program (STP) 191 462 030591OF SPACETRACK 85 195 0604233F Specialized...is in the mid- 1990’s. Combat force commanders and units (equipped with EMP-hardened, secure radio equipment) interact with nearby relay nodes for

14 CFR 121.913 - Qualification curriculum.

Code of Federal Regulations, 2014 CFR

2014-01-01

... REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Advanced Qualification Program § 121.913... planned hours of training, evaluation, and supervised operating experience. (b) For crewmembers, aircraft... activities that are aircraft- and equipment-specific to qualify a person for a particular duty position on...

14 CFR 121.913 - Qualification curriculum.

Code of Federal Regulations, 2013 CFR

2013-01-01

... REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Advanced Qualification Program § 121.913... planned hours of training, evaluation, and supervised operating experience. (b) For crewmembers, aircraft... activities that are aircraft- and equipment-specific to qualify a person for a particular duty position on...

14 CFR 121.913 - Qualification curriculum.

Code of Federal Regulations, 2012 CFR

2012-01-01

... REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Advanced Qualification Program § 121.913... planned hours of training, evaluation, and supervised operating experience. (b) For crewmembers, aircraft... activities that are aircraft- and equipment-specific to qualify a person for a particular duty position on...

Evaluation of the ADAPTIR System for Work Zone Traffic Control

DOT National Transportation Integrated Search

1999-11-01

The ADAPTIR system (Automated Data Acquisition and Processing of Traffic Information in Real Time) uses variable message signs (VMS) equipped with radar units, along with a software program to interpret the data, to display appropriate warning and ad...

Five-week sensory motor training program improves functional performance and postural control in young male soccer players - A blind randomized clinical trial.

PubMed

Heleno, Lucas Rafael; da Silva, Rubens A; Shigaki, Leonardo; Araújo, Cynthia Gobbi Alves; Coelho Candido, Cristiane Regina; Okazaki, Victor Hugo Alves; Frisseli, Ariobaldo; Macedo, Christiane de S Guerino

2016-11-01

Sensory motor training programs are used in the rehabilitation and prevention of injuries among soccer players. Inconsistencies are found in the literature regarding the duration of the protocols and the exercises and equipment used. To evaluate the benefits of a five-week sensory motor training program on the functional performance and postural control of young soccer players. The study sample comprised 22 young male soccer players who were evaluated using: the Figure-of-Eight Test (F8), Side Hop Test (SHT), Star Excursion Balance Test (SEBT), and a force platform. The players were randomly divided into a control group (N = 10), who continued their soccer practice sessions and an intervention group (N = 12), who continued their soccer practice sessions and were also enrolled in a supervised five-week sensory motor training program. After the five-week training program, the intervention group obtained significant results in the F8, SHT and SEBT, as well as in the following parameters: area of pressure of sway center (COP), mean velocity and mean frequency of COP. The five-week sensory motor training program, carried out with easily available and low cost equipment, was effective at improving functional performance and postural control in young soccer players. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Global Review of Incentive Programs to Accelerate Energy-Efficient Appliances and Equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

de la Rue du Can, Stephane; Phadke, Amol; Leventis, Greg

Incentive programs are an essential policy tool to move the market toward energy-efficient products. They offer a favorable complement to mandatory standards and labeling policies by accelerating the market penetration of energy-efficient products above equipment standard requirements and by preparing the market for increased future mandatory requirements. They sway purchase decisions and in some cases production decisions and retail stocking decisions toward energy-efficient products. Incentive programs are structured according to their regulatory environment, the way they are financed, by how the incentive is targeted, and by who administers them. This report categorizes the main elements of incentive programs, using casemore » studies from the Major Economies Forum to illustrate their characteristics. To inform future policy and program design, it seeks to recognize design advantages and disadvantages through a qualitative overview of the variety of programs in use around the globe. Examples range from rebate programs administered by utilities under an Energy-Efficiency Resource Standards (EERS) regulatory framework (California, USA) to the distribution of Eco-Points that reward customers for buying efficient appliances under a government recovery program (Japan). We found that evaluations have demonstrated that financial incentives programs have greater impact when they target highly efficient technologies that have a small market share. We also found that the benefits and drawbacks of different program design aspects depend on the market barriers addressed, the target equipment, and the local market context and that no program design surpasses the others. The key to successful program design and implementation is a thorough understanding of the market and effective identification of the most important local factors hindering the penetration of energy-efficient technologies.« less

Brief Lags in Interrupted Sequential Performance: Evaluating a Model and Model Evaluation Method

DTIC Science & Technology

2015-01-05

rehearsal mechanism in the model. To evaluate the model we developed a simple new goodness-of-fit test based on analysis of variance that offers an...repeated step). Sequen- tial constraints are common in medicine, equipment maintenance, computer programming and technical support, data analysis ...legal analysis , accounting, and many other home and workplace environ- ments. Sequential constraints also play a role in such basic cognitive processes

Laboratory Resources Management in Manufacturing Systems Programs

ERIC Educational Resources Information Center

Obi, Samuel C.

2004-01-01

Most, if not all, industrial technology (IT) programs have laboratories or workshops. Often equipped with modern equipment, tools, materials, and measurement and test instruments, these facilities constitute a major investment for IT programs. Improper use or over use of program facilities may result in dirty lab equipment, lost or damaged tools,…

Evaluating the Effectiveness and the Impact of Donated Neurosurgical Equipment on Neurosurgical Units in Low- and Middle-Income Countries: The World Federation of Neurosurgical Societies Experience.

PubMed

Venturini, Sara; Park, Kee B

2018-01-01

Surgical practice highly depends on the availability of surgical equipment; this is particularly relevant to low- and middle-income countries (LMICs), where resources are limited. A key part of the efforts to improve surgical provision globally include providing affordable equipment to LMICs; however, the effectiveness and the impact of these initiatives have not yet been assessed. We aimed to evaluate the World Federation of Neurosurgical Societies neurosurgical equipment program in this context. Recipients were identified from the World Federation of Neurosurgical Societies records; contact details were gathered. An online survey was used to collect data on equipment, including its current use, any malfunctioning issues, suitability, reliability, serviceability, and the impact it has had on the unit. Responses were received from 16 units, totaling 28 pieces of equipment. A total of 75% of the equipment is still in use; of this, 57% is fully functioning, and 43% is used despite some malfunction. We found that 25% of the equipment is broken and unusable; high-maintenance items, such as high-speed drills, feature in this category (100% broken, n = 3). Units reported an increase in number of operation performed in 74% cases, improved surgery quality in 78%, and breadth of operations in 44%. Satisfaction, equipment suitability, reliability, and serviceability scored highly, with median values of 9 for all fields on a 10-point scale. Equipment donation positively impacts neurosurgical units in LMICs by allowing expansion of neurosurgical practice, improved safety and quality, and affordability. Adequate follow-up, considerations regarding equipment durability and maintenance needs, and improved support for repairs should be prioritized to ensure maximal benefit. Copyright © 2017 Elsevier Inc. All rights reserved.

45 CFR 74.34 - Equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... equipment with a current per unit fair market value of $5000 or more, the recipient may retain the equipment... the original project or program to the current fair market value of the equipment. If the recipient... project or program to the current fair market value of the equipment, plus any reasonable shipping or...

Use of Computer Simulation in Designing and Evaluating a Proposed Rough Mill for Furniture Interior Parts

Treesearch

Philip A. Araman

1977-01-01

The design of a rough mill for the production of interior furniture parts is used to illustrate a simulation technique for analyzing and evaluating established and proposed sequential production systems. Distributions representing the real-world random characteristics of lumber, equipment feed speeds and delay times are programmed into the simulation. An example is...

Evaluation of the LiveWell@School Food Initiative Shows Increases in Scratch Cooking and Improvement in Nutritional Content

ERIC Educational Resources Information Center

Schober, Daniel J.; Carpenter, Leah; Currie, Venita; Yaroch, Amy L.

2016-01-01

Background: The purpose of this evaluation was to examine the effects of the LiveWell@School Food Initiative (LW@SFI), a Colorado-based childhood obesity prevention program that partners with school districts to enable them to serve more scratch cooked foods through culinary training, action planning, and equipment grants. Methods: This evaluation…

10 CFR 70.72 - Facility changes and change process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... management system to evaluate, implement, and track each change to the site, structures, processes, systems, equipment, components, computer programs, and activities of personnel. This system must be documented in... licensed material; (3) Modifications to existing operating procedures including any necessary training or...

10 CFR 70.72 - Facility changes and change process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... management system to evaluate, implement, and track each change to the site, structures, processes, systems, equipment, components, computer programs, and activities of personnel. This system must be documented in... licensed material; (3) Modifications to existing operating procedures including any necessary training or...

10 CFR 70.72 - Facility changes and change process.

Code of Federal Regulations, 2012 CFR

2012-01-01

... management system to evaluate, implement, and track each change to the site, structures, processes, systems, equipment, components, computer programs, and activities of personnel. This system must be documented in... licensed material; (3) Modifications to existing operating procedures including any necessary training or...

10 CFR 70.72 - Facility changes and change process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... management system to evaluate, implement, and track each change to the site, structures, processes, systems, equipment, components, computer programs, and activities of personnel. This system must be documented in... licensed material; (3) Modifications to existing operating procedures including any necessary training or...

10 CFR 70.72 - Facility changes and change process.

Code of Federal Regulations, 2013 CFR

2013-01-01

... management system to evaluate, implement, and track each change to the site, structures, processes, systems, equipment, components, computer programs, and activities of personnel. This system must be documented in... licensed material; (3) Modifications to existing operating procedures including any necessary training or...

Automatic design of optical systems by digital computer

NASA Technical Reports Server (NTRS)

Casad, T. A.; Schmidt, L. F.

1967-01-01

Computer program uses geometrical optical techniques and a least squares optimization method employing computing equipment for the automatic design of optical systems. It evaluates changes in various optical parameters, provides comprehensive ray-tracing, and generally determines the acceptability of the optical system characteristics.

Education and equipment for people who smoke crack cocaine in Canada: progress and limits.

PubMed

Strike, Carol; Watson, Tara Marie

2017-05-12

People who smoke crack cocaine experience a wide variety of health-related issues. However, public health programming designed for this population is limited, particularly in comparison with programming for people who inject drugs. Canadian best practice recommendations encourage needle and syringe programs (NSPs) to provide education about safer crack cocaine smoking practices, distribute safer smoking equipment, and provide options for safer disposal of used equipment. We conducted an online survey of NSP managers across Canada to estimate the proportions of NSPs that provide education and distribute safer smoking equipment to people who smoke crack cocaine. We also assessed change in pipe distribution practices between 2008 and 2015 in the province of Ontario. Analysis of data from 80 programs showed that the majority (0.76) provided education to clients on reducing risks associated with sharing crack cocaine smoking equipment and about when to replace smoking equipment (0.78). The majority (0.64) also distributed safer crack cocaine smoking equipment and over half of these programs (0.55) had done so for less than 5 years. Among programs that distributed pipes, 0.92 distributed the recommended heat-resistant Pyrex and/or borosilicate glass pipes. Only 0.50 of our full sample reported that their program provides clients with containers for safer disposal of used smoking equipment. The most common reasons for not distributing safer smoking equipment were not enough funding (0.32) and lack of client demand (0.25). Ontario-specific sub-analyses showed a significant increase in the proportion of programs distributing pipes in Ontario from 0.15 (2008) to 0.71 (2015). Our findings point to important efforts by Canadian NSPs to reduce harm among people who smoke crack cocaine through provision of education and equipment, but there are still limits that could be addressed. Our study can provide guidance for future cross-jurisdiction studies to describe relationships involving harm reduction programs and provision of safer crack cocaine smoking education and equipment.

Evaluation of Rankine cycle air conditioning system hardware by computer simulation

NASA Technical Reports Server (NTRS)

Healey, H. M.; Clark, D.

1978-01-01

A computer program for simulating the performance of a variety of solar powered Rankine cycle air conditioning system components (RCACS) has been developed. The computer program models actual equipment by developing performance maps from manufacturers data and is capable of simulating off-design operation of the RCACS components. The program designed to be a subroutine of the Marshall Space Flight Center (MSFC) Solar Energy System Analysis Computer Program 'SOLRAD', is a complete package suitable for use by an occasional computer user in developing performance maps of heating, ventilation and air conditioning components.

Improved ultrasonic standard reference blocks

NASA Technical Reports Server (NTRS)

Eitzen, D. G.

1975-01-01

A program to improve the quality, reproducibility and reliability of nondestructive testing through the development of improved ASTM-type ultrasonic reference standards is described. Reference blocks of aluminum, steel, and titanium alloys were considered. Equipment representing the state-of-the-art in laboratory and field ultrasonic equipment was obtained and evaluated. Some RF and spectral data on ten sets of ultrasonic reference blocks were taken as part of a task to quantify the variability in response from nominally identical blocks. Techniques for residual stress, preferred orientation, and microstructural measurements were refined and are applied to a reference block rejected by the manufacturer during fabrication in order to evaluate the effect of metallurgical condition on block response.

Evaluation of critical indicators in the process of acquiring supplies and services LAC-UFPE

NASA Astrophysics Data System (ADS)

Caetano, V. F.; Ferreira, C. V.; dos Santos, M. J.; Honorato, F. A.

2015-01-01

In laboratories linked to public universities and accredited by the NBR ISO/IEC 17025, to meet efficiently item 4.6 (procurement of supplies and services) is a challenge that can be accomplished by programming based on historical purchases and services. In this study, we evaluated the critical procurement items to meet the quality management system of the LAC-UFPE: reagents, certified reference material, of equipment parts, maintenance and calibration of equipment and instruments. It was found that the most critical item is the certified reference material, the purchase or repair of which must be expedited within 125 days prior to the receipt to occur within the desired period.

Conduct overall test operations and evaluate two Doppler systems to detect, track and measure velocities in aircraft wake vortices

NASA Technical Reports Server (NTRS)

Wilson, D. J.; Krause, M. C.; Craven, C. E.; Edwards, B. B.; Coffey, E. W.; Huang, C. C.; Jetton, J. L.; Morrison, L. K.

1974-01-01

A program plan for system evaluation of the two-dimensional Scanning Laser Doppler System (SLDS) is presented. In order to meet system evaluation and optimization objectives the following tests were conducted: (1) noise tests; (2) wind tests; (3) blower flowfield tests; (4) single unit (1-D) flyby tests; and (5) dual unit (2-D) flyby tests. Test results are reported. The final phase of the program included logistics preparation, equipment interface checkouts, and data processing. It is concluded that the SLDS is capable of accurately tracking aircraft wake vortices from small or large aircraft, and in any type of weather.

Quality Assurance Program for Molecular Medicine Laboratories

PubMed Central

Hajia, M; Safadel, N; Samiee, S Mirab; Dahim, P; Anjarani, S; Nafisi, N; Sohrabi, A; Rafiee, M; Sabzavi, F; Entekhabi, B

2013-01-01

Background: Molecular diagnostic methods have played and continuing to have a critical role in clinical laboratories in recent years. Therefore, standardization is an evolutionary process that needs to be upgrade with increasing scientific knowledge, improvement of the instruments and techniques. The aim of this study was to design a quality assurance program in order to have similar conditions for all medical laboratories engaging with molecular tests. Methods: We had to design a plan for all four elements; required space conditions, equipments, training, and basic guidelines. Necessary guidelines was prepared and confirmed by the launched specific committee at the Health Reference Laboratory. Results: Several workshops were also held for medical laboratories directors and staffs, quality control manager of molecular companies, directors and nominees from universities. Accreditation of equipments and molecular material was followed parallel with rest of program. Now we are going to accredit medical laboratories and to evaluate the success of the program. Conclusion: Accreditation of medical laboratory will be succeeding if its basic elements are provided in advance. Professional practice guidelines, holding training and performing accreditation the molecular materials and equipments ensured us that laboratories are aware of best practices, proper interpretation, limitations of techniques, and technical issues. Now, active external auditing can improve the applied laboratory conditions toward the defined standard level. PMID:23865028

Quality assurance program for molecular medicine laboratories.

PubMed

Hajia, M; Safadel, N; Samiee, S Mirab; Dahim, P; Anjarani, S; Nafisi, N; Sohrabi, A; Rafiee, M; Sabzavi, F; Entekhabi, B

2013-01-01

Molecular diagnostic methods have played and continuing to have a critical role in clinical laboratories in recent years. Therefore, standardization is an evolutionary process that needs to be upgrade with increasing scientific knowledge, improvement of the instruments and techniques. The aim of this study was to design a quality assurance program in order to have similar conditions for all medical laboratories engaging with molecular tests. We had to design a plan for all four elements; required space conditions, equipments, training, and basic guidelines. Necessary guidelines was prepared and confirmed by the launched specific committee at the Health Reference Laboratory. Several workshops were also held for medical laboratories directors and staffs, quality control manager of molecular companies, directors and nominees from universities. Accreditation of equipments and molecular material was followed parallel with rest of program. Now we are going to accredit medical laboratories and to evaluate the success of the program. Accreditation of medical laboratory will be succeeding if its basic elements are provided in advance. Professional practice guidelines, holding training and performing accreditation the molecular materials and equipments ensured us that laboratories are aware of best practices, proper interpretation, limitations of techniques, and technical issues. Now, active external auditing can improve the applied laboratory conditions toward the defined standard level.

Methodology and measures for preventing unacceptable flow-accelerated corrosion thinning of pipelines and equipment of NPP power generating units

NASA Astrophysics Data System (ADS)

Tomarov, G. V.; Shipkov, A. A.; Lovchev, V. N.; Gutsev, D. F.

2016-10-01

Problems of metal flow-accelerated corrosion (FAC) in the pipelines and equipment of the condensate- feeding and wet-steam paths of NPP power-generating units (PGU) are examined. Goals, objectives, and main principles of the methodology for the implementation of an integrated program of AO Concern Rosenergoatom for the prevention of unacceptable FAC thinning and for increasing operational flow-accelerated corrosion resistance of NPP EaP are worded (further the Program). A role is determined and potentialities are shown for the use of Russian software packages in the evaluation and prediction of FAC rate upon solving practical problems for the timely detection of unacceptable FAC thinning in the elements of pipelines and equipment (EaP) of the secondary circuit of NPP PGU. Information is given concerning the structure, properties, and functions of the software systems for plant personnel support in the monitoring and planning of the inservice inspection of FAC thinning elements of pipelines and equipment of the secondary circuit of NPP PGUs, which are created and implemented at some Russian NPPs equipped with VVER-1000, VVER-440, and BN-600 reactors. It is noted that one of the most important practical results of software packages for supporting NPP personnel concerning the issue of flow-accelerated corrosion consists in revealing elements under a hazard of intense local FAC thinning. Examples are given for successful practice at some Russian NPP concerning the use of software systems for supporting the personnel in early detection of secondary-circuit pipeline elements with FAC thinning close to an unacceptable level. Intermediate results of working on the Program are presented and new tasks set in 2012 as a part of the updated program are denoted. The prospects of the developed methods and tools in the scope of the Program measures at the stages of design and construction of NPP PGU are discussed. The main directions of the work on solving the problems of flow-accelerated corrosion of pipelines and equipment in Russian NPP PGU are defined.

Space station wardroom habitability and equipment study

NASA Technical Reports Server (NTRS)

Nixon, David; Miller, Christopher; Fauquet, Regis

1989-01-01

Experimental designs in life-size mock-up form for the wardroom facility for the Space Station Habitability Module are explored and developed. In Phase 1, three preliminary concepts for the wardroom configuration are fabricated and evaluated. In Phase 2, the results of Phase 1 are combined with a specific range of program design requirements to provide the design criteria for the fabrication of an innovative medium-fidelity mock-up of a wardrobe configuration. The study also focuses on the design and preliminary prototyping of selected equipment items including crew exercise compartments, a meal/meeting table and a portable workstation. Design criteria and requirements are discussed and documented. Preliminary and final mock-ups and equipment prototypes are described and illustrated.

Systems design study of the Pioneer Venus spacecraft. Volume 2. Preliminary program development plan

NASA Technical Reports Server (NTRS)

1973-01-01

The preliminary development plan for the Pioneer Venus program is presented. This preliminary plan treats only developmental aspects that would have a significant effect on program cost. These significant development areas were: master program schedule planning; test planning - both unit and system testing for probes/orbiter/ probe bus; ground support equipment; performance assurance; and science integration Various test planning options and test method techniques were evaluated in terms of achieving a low-cost program without degrading mission performance or system reliability. The approaches studied and the methodology of the selected approach are defined.

EMMA: The expert system for munition maintenance

NASA Technical Reports Server (NTRS)

Mullins, Barry E.

1988-01-01

Expert Missile Maintenance Aid (EMMA) is a first attempt to enhance maintenance of the tactical munition at the field and depot level by using artificial intelligence (AI) techniques. The ultimate goal of EMMA is to help a novice maintenance technician isolate and diagnose electronic, electromechanical, and mechanical equipment faults to the board/chassis level more quickly and consistently than the best human expert using the best currently available automatic test equipment (ATE). To this end, EMMA augments existing ATE with an expert system that captures the knowledge of design and maintenance experts. The EMMA program is described, including the evaluation of field-level expert system prototypes, the description of several study tasks performed during EMMA, and future plans for a follow-on program. This paper will briefly address several study tasks performed during EMMA. The paper concludes with a discussion of future plans for a follow-on program and other areas of concern.

The history and development of NASA survival equipment.

NASA Technical Reports Server (NTRS)

Radnofsky, M. I.

1972-01-01

A research and development program on survival equipment was begun in early 1960 with the Mercury Program. The Mercury survival kit is discussed together with Gemini survival equipment, and Apollo I survival equipment. A study program is conducted to assess potential survival problems that may be associated with future space flights landing in polar waters. Survival kit requirements for applications on the Skylab program are also considered. Other investigations are concerned with the design of a global survival kit in connection with Space Shuttle missions.

Human Factors Engineering Program for Intercontinental Ballistic Missile Systems, (MIL-STD-1794(USAF))

DTIC Science & Technology

1986-10-01

opeational test and evaluation (OT&R). The OT&B Is comprised of Initial operational test and evaluation ( IOT &R) and follow-on test and evaluation (FOT&R). OT&I...BP HYL FVAC beating, ventilation and air conditioning am. ICBM Intercntinental ballistic missile an. IOT &R Initial operational test and *valuation so...and maintenance vehicles (stop- B pod, engine idle-exterior), facility equipment utility rooms, heating, ventilation and air conditioning ( HVAC

Expense comparison of a telemedicine practice versus a traditional clinical practice.

PubMed

Barker, Gail P; Krupinski, Elizabeth A; Schellenberg, Bonnie; Weinstein, Ronald S

2004-01-01

This paper compares the expenses of a telemedicine program to those of a traditional clinical practice using data from two fiscal years (FY) 1998/1999 and 2000/2001. As part of that evaluation, we compared expenses of the University of Arizona's clinical practice group, the University Physicians Incorporated (UPI), to those of the Arizona Telemedicine Program (ATP) practice. For this study, we used the reporting categories published in the year-end UPI financial statement. These categories included clinical services, administration, equipment depreciation, and overhead. Results showed that clinical service expenses and administrative expenses for FY 2000/2001 were higher in the traditional UPI practice, whereas equipment depreciation and overhead expenses are higher in the telemedicine practice. This differs somewhat from FY 1998/1999, where clinical expenses and overhead were higher in the UPI practice and administration and equipment depreciation were higher in the telemedicine practice. We will discuss the relevance of these results and the critical factors that contribute to these differences.

Implementing Basic Education: An African Experience.

ERIC Educational Resources Information Center

Banya, Kingsley; Elu, Juliet

1999-01-01

Analyses some of the difficulties involved in implementing the recently approved Basic Education Program for primary and secondary education in Sierra Leone. Discusses issues such as funding, training, and retention of teachers, curriculum reform, language development, equipment and supplies, and evaluation. Concludes that political stability is…

30 CFR 582.23 - Testing Plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... detailed Mining Plan than is obtainable under an approved Delineation Plan, to prepare feasibility studies, to carry out a pilot program to evaluate processing techniques or technology or mining equipment, or...

30 CFR 582.23 - Testing Plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... detailed Mining Plan than is obtainable under an approved Delineation Plan, to prepare feasibility studies, to carry out a pilot program to evaluate processing techniques or technology or mining equipment, or...

30 CFR 582.23 - Testing Plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OPERATIONS IN THE OUTER... detailed Mining Plan than is obtainable under an approved Delineation Plan, to prepare feasibility studies, to carry out a pilot program to evaluate processing techniques or technology or mining equipment, or...

Cost Differentials and the Treatment of Equipment Assets: An Analysis of Alternatives.

ERIC Educational Resources Information Center

Frohreich, Lloyd E.

This paper is a discussion of alternative state approaches to aiding and costing capital outlay programs, particularly equipment purchases for vocational programs. Equipment costs for vocational programs tend to be a larger proportion of the total costs than in other programs. The paper includes a discussion of such topics as the magnitude of…

Safety assessment for EPS electron-proton spectrometer

NASA Technical Reports Server (NTRS)

Gleeson, P.

1971-01-01

A safety analysis was conducted to identify the efforts required to assure relatively hazard free operation of the EPS and to meet the safety requirements of the program. Safety engineering criteria, principles, and techniques in applicable disciplines are stressed in the performance of the system and subsystem studies; in test planning; in the design, development, test, evaluation, and checkout of the equipment; and the operating procedures for the EPS program.

Digital Equipment Corporation VAX/VMS Version 4.3

DTIC Science & Technology

1986-07-30

operating system performs process-oriented paging that allows execution of programs that may be larger than the physical memory allocated to them... to higher privileged modes. (For an explanation of how the four access modes provide memory access protection see page 9, "Memory Management".) A... to optimize program performance for real-time applications or interactive environments. July 30, 1986 - 4 - Final Evaluation Report Digital VAX/VMS

The role of physical examinations and education in prospective medicine

NASA Technical Reports Server (NTRS)

Jones, W. L.; Mockbee, J.; Snow, C. K.; Compton, J. R.

1978-01-01

NASA's prospective medicine program, with the principal elements of physical examinations and an educational program for health awareness is described. Participation in the voluntary physical examination program is increasing. In 1976 13,621 employees were given partial or complete examination in NASA Health Units. From the 941 examinations performed at NASA Headquarters in 1976, 522 principal findings were detected. Equipment and techniques in exercise EKG, tonometry, and colonoscopy were partially responsible for this high rate. The health awareness program includes consultations with physicians, training devices and courses, health bulletins, and special screening programs. Epidemiological studies, now underway, will be used to evaluate the health awareness programs.

Satellite services system analysis study. Volume 5: Programmatics

NASA Technical Reports Server (NTRS)

1981-01-01

The overall program and resources needed for development and operation of a Satellite Services System is reviewed. Program requirements covered system operations through 1993 and were completed in preliminary form. Program requirements were refined based on equipment preliminary design and analysis. Schedules, costs, equipment utilization, and facility/advanced technology requirements were included in the update. Equipment user charges were developed for each piece of equipment and for representative satellite servicing missions.

Integrating care coordination home telehealth and home based primary care in rural Oklahoma: a pilot study.

PubMed

Sorocco, Kristen H; Bratkovich, Kristi L; Wingo, Rita; Qureshi, Saleem M; Mason, Patrick J

2013-08-01

The purpose of this program was to evaluate the benefits of integrating VA Care Coordination Home Telehealth and Telemental health within HBPC. A case study design was used to determine quality assurance and quality improvement of incorporating additional home telehealth equipment within Home Based Primary Care (HBPC). Veterans with complex medical conditions and their caregivers living in rural Oklahoma were enrolled. Veterans received the same care other HBPC patients received with the addition of home telehealth equipment. Members from the interdisciplinary treatment team were certified to use the telehealth equipment. Veterans and their caregivers were trained on use of the equipment in their homes. Standard HBPC program measures were used to assess the program success. Assessments from all disciplines on the HBPC team were at baseline, 3, and 6 months, and participants provided satisfaction and interview data to assess the benefits of integrating technology into standard care delivery within an HBPC program. Six veterans were enrolled (mean age = 72 yrs) with a range of physical health conditions including: chronic obstructive pulmonary disease, cerebrovascular accident, spinal cord injury, diabetes, hypertension, and syncope. Primary mental health conditions included depression, dementia, anxiety, and PTSD. Scores on the Mini-Mental State Examination ranged from 18 to 30. Over a 6-month period, case studies indicated improvements in strength, social functioning, decreased caregiver burden, and compliance with treatment plan. This integration of CCHT and HBPC served previously underserved rural veterans having complex medical conditions and appears both feasible and clinically beneficial to veterans and their caregivers. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Engineering and Development Support of General Decon Technology for the DARCOM Installation Restoration Program. Task 2. Treatment of Explosives Contaminated Lagoon Sediment. Phase I. Literature Review and Evaluation

DTIC Science & Technology

1980-11-01

hr incineration rate are presented in Table 15. These costs include dredging equipment, flat bed trailer and afterburners and venturi scrubbers where...require further treatment before they can be released into the environment, i.e. biological degradation for the liquid and specific scrubbers for the...The wet-air units are equipped with wet scrubbers to remove air emissions. Air emissions are expected to contain at a minimum CO, C0 2 ,N2 , 0, and

The Soldier-Athlete Initiative: Program Evaluation of the Effectiveness of Athletic Trainers Compared to Musculoskeletal Action Teams in Initial Entry Training, Fort Leonard Wood, June 2010 - December 2011

DTIC Science & Technology

2012-10-01

skills and injury prevention methods applied by ATs in sports and exercise situations may also be applicable to recruits in IET. In late 2009, the...able to assure that physical training exercises are carried out in a manner to optimize mission readiness and minimize the incidence of injury. In...facility with a 21-piece Nautilus set and aerobic exercise equipment. Money spent on the equipment/facility was recouped within 10 months and there was

GSDO Program Hexavalent Chrome Alternatives: Final Pretreatments Test Report

NASA Technical Reports Server (NTRS)

Kessel, Kurt

2013-01-01

Hexavalent chrome free pretreatments should be considered for use on Ground Support Equipment (OSE) and Electrical Ground Support Equipment (EOSE). Both of the hexavalent chrome free pretreatments (Metalast TCP HF and SurTec 650C) evaluated by this project met, and in some instances exceeded, the requirements ofMIL-DTL-5541 "Chemical Conversion Coatings on Aluminum and Aluminum Alloys". For DC resistance measurements, both Metalast TCP HF and SurTec (!50C met initial requirements following assembly and in many cases continued to maintain passing readings for the duration of testing.

14 CFR 135.336 - Airline transport pilot certification training program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (v) Evaluation. (4) If providing training in a flight simulation training device, holds an aircraft type rating for the aircraft represented by the flight simulation training device utilized in the... simulation; (iv) Minimum equipment requirements for each curriculum; and (v) The maneuvers that will be...

Effects of Psychoeducation for Offenders in a Community Correctional Facility

ERIC Educational Resources Information Center

Liau, Albert K.; Shively, Randy; Horn, Mary; Landau, Jennifer; Barriga, Alvaro; Gibbs, John C.

2004-01-01

The present study provided a randomized outcome evaluation of the psychoeducational component of the EQUIP program. The psychoeducational curriculum was implemented in a community correctional facility for adult felony offenders. The psychoeducational curriculum is designed to remedy offenders' delays in moral judgment maturity, social cognitive…

A Guide to Curriculum Planning in Foreign Language.

ERIC Educational Resources Information Center

Wisconsin State Dept. of Public Instruction, Madison.

A guide designed to help local curriculum planners develop and implement curriculums to provide all students with equal access to foreign languages provides an overview of current philosophies, objectives, methods, materials, and equipment and a guide to sequential program development, articulation, and evaluation. An introductory section…

77 FR 38375 - Advisory Circular (AC) 150/5345-53D, Airport Lighting Equipment Certification Program; Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-27

...The FAA proposes to replace AC150/5345-53C with AC150/5345-53D to clarify the criteria under the Airport Lighting Equipment Certification Program (ALECP) for acceptance of an organization as a third party certification body (third party certifier) and how manufacturers may get equipment qualified under the program. The Secretary of Transportation is providing notice in the Federal Register of, and an opportunity for public comment on AC150/5345-53D, Airport Lighting Equipment Certification Program.

77 FR 16769 - Energy Conservation Program for Certain Industrial Equipment: Energy Conservation Standards and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-22

... Conservation Program for Certain Industrial Equipment: Energy Conservation Standards and Test Procedures for...-Conditioning Engineers (ASHRAE)/Illuminating Engineering Society of North America (IESNA) Standard 90.1-2010... Industrial Equipment, which includes the commercial heating, air-conditioning, and water-heating equipment...

75 FR 71596 - Energy Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

... Efficiency Program for Certain Commercial and Industrial Equipment: Test Procedures for Commercial Refrigeration Equipment AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION... amendments to its test procedure for commercial refrigeration equipment (CRE). The amendments would update...

NASA electronic message experiment and study: Detailed test plans

NASA Technical Reports Server (NTRS)

1979-01-01

A methodology for evaluating the utility of high speed digital facsimile as a component of the projected NASA-wide electronic message network is presented. Equipment checkout, operator familiarization, pretest calibration, and the development of procedures are addressed. An experimental test program of the facsimile message service which will carry duplicates of the actual messages sent by other means is highlighted. Also, an operational test program during which messages will be sent on a regular basis in order to accumulate the information that will be used to evaluate system performance and project future growth is described.

Indoor pollutants emitted by office equipment: A review ofreported data and information needs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Destaillats, Hugo; Maddalena, Randy L.; Singer, Brett C.

2007-02-01

There is concern that potentially harmful pollutants may be emitted from office equipment. Although office equipment has been a focal point for governmental efforts to promote energy efficiency through programs such as the US EPA's Energy Star, little is known about the relationship between office equipment use and indoor air quality, and information on pollutant emissions is sparse. In this review, we summarize available information on emission rates and/or ambient concentrations of various pollutants that are related to office equipment use. Experimental methods used in the characterization of emissions are briefly described. The office equipment evaluated in this review includesmore » computers (desktops and notebooks), printers (laser, ink-jet and all-in-one machines) and photocopy machines. Reported emission rates of the following pollutant groups are summarized: volatile organic chemicals (VOCs), ozone, particulate matter and several semivolatile organic chemicals (SVOCs). The latter include phthalate esters, brominated flame retardants, organophosphate flame retardants and polycyclic aromatic hydrocarbons (PAHs). We also review studies reporting airborne concentrations in indoor environments where office equipment was present and thought to be a significant contributor to the total pollutant burden (offices, residences, schools, electronics recycling plants). For certain pollutants, such as organophosphate flame retardants, the link between emission by office equipment and indoor air concentrations is relatively well established. However, indoor VOCs, ozone, PAHs and phthalate esters can originate from a variety of sources, and their source apportionment is less straightforward. This literature review identifies substances of toxicological significance, with the purpose of serving as a guide to evaluate their potential importance with respect to human exposures.« less

Evaluation of the Tactical Human Optimization, Rapid Rehabilitation, and Reconditioning Program (THOR3)

DTIC Science & Technology

2016-10-01

0.3-0.9). Evidence from this evaluation suggests that ARSOF Soldiers may benefit from participation in THOR3 compared to other human performance...factor that was not modifiable and one of the strongest risk factors for injury. Evidence from this evaluation suggests that Soldiers may benefit from...a Motorized Vehicle 7 2 Walking or Hiking 7 2 Rough Housing or Fighting 3 1 Stepping/Climbing 1 < 1 Repairing or maintaining equipment 1

42 CFR 495.354 - Rules for charging equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Rules for charging equipment. 495.354 Section 495.354 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES... PROGRAM Requirements Specific to the Medicaid Program § 495.354 Rules for charging equipment. Equipment...

41 CFR 101-26.507 - Security equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 2 2013-07-01 2012-07-01 true Security equipment. 101... PROGRAM 26.5-GSA Procurement Programs § 101-26.507 Security equipment. Federal agencies and other activities authorized to purchase security equipment through GSA sources shall do so in accordance with the...

41 CFR 101-26.507 - Security equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Security equipment. 101... PROGRAM 26.5-GSA Procurement Programs § 101-26.507 Security equipment. Federal agencies and other activities authorized to purchase security equipment through GSA sources shall do so in accordance with the...

41 CFR 101-26.507 - Security equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Security equipment. 101... PROGRAM 26.5-GSA Procurement Programs § 101-26.507 Security equipment. Federal agencies and other activities authorized to purchase security equipment through GSA sources shall do so in accordance with the...

41 CFR 101-26.507 - Security equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Security equipment. 101... PROGRAM 26.5-GSA Procurement Programs § 101-26.507 Security equipment. Federal agencies and other activities authorized to purchase security equipment through GSA sources shall do so in accordance with the...

34 CFR 76.661 - Equipment and supplies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Equipment and supplies. 76.661 Section 76.661 Education... Equipment and supplies. (a) Under some program statutes, a public agency must keep title to and exercise continuing administrative control of all equipment and supplies that the subgrantee acquires with program...

Analytical evaluation of ILM sensors. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Kirk, R. J.

1975-01-01

The applicability of various sensing concepts to independent landing monitor systems was analyzed. Microwave landing system MLS accuracy requirements are presented along with a description of MLS airborne equipment. Computer programs developed during the analysis are described and include: a mathematical computer model for use in the performance assessment of reconnaissance sensor systems; a theoretical formulation of electromagnetic scattering to generate data at high incidence angles; atmospheric attenuation of microwaves; and microwave radiometry, programs

Development of a recovery education program for inpatient mental health providers.

PubMed

Chen, Shu-Ping; Krupa, Terry; Lysaght, Rosemary; McCay, Elizabeth; Piat, Myra

2014-12-01

Mental health system transformation toward a recovery-orientation has created a demand for education to equip providers with recovery competencies. This report describes the development of a recovery education program designed specifically for inpatient providers. Part 1 of the education is a self-learning program introducing recovery concepts and a recovery competency framework; Part 2 is a group-learning program focusing on real-life dilemmas and applying the Appreciative Inquiry approach to address these clinical dilemmas. A pilot study with a pretest/posttest design was used to evaluate the program. Participants included 26 inpatient multidisciplinary providers from 3 hospitals. The results showed participants' improvement on recovery knowledge (z = -2.55, p = .011) after the self-learning program. Evaluations of the group-learning program were high (4.21 out of 5). These results support continued efforts to refine the program. Inpatient providers could use this program to lead interprofessional practice in promoting recovery. (c) 2014 APA, all rights reserved.

78 FR 49202 - Energy Conservation Program for Certain Commercial and Industrial Equipment: Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-13

.... EERE-2013-BT-STD-0030] RIN 1904-AD01 Energy Conservation Program for Certain Commercial and Industrial... efficiency of certain industrial equipment to conserve the energy resources of the Nation. DATES: DOE will... codification in the U.S. Code, establishes the ``Energy Conservation Program for Certain Industrial Equipment...

Planning and Equipping School Lunchrooms. Bulletin, 1946, No. 19

ERIC Educational Resources Information Center

US Office of Education, Federal Security Agency, 1946

1946-01-01

In many schools, plans are underway to expand facilities to include necessary space and equipment for providing adequate school lunch programs. This bulletin furnishes basic materials on which school people may plan space and equipment for new school lunch programs or appraise existing programs to determine what improvements in arrangement or…

Durable medical equipment recycling: a pilot program.

PubMed

Wright, Aaron J

2012-01-01

Our unfunded trauma patients often lack the access to adequate health care services and equipment after hospital discharge. We have developed and implemented a pilot program to provide reclaimed durable medical equipment to medically indigent trauma patients. Our program includes the reuse of items such as front-wheeled walkers, bedside commodes, shower chairs, crutches, and canes.

Measurement. Teacher's Guide. Small Engine Repair Series.

ERIC Educational Resources Information Center

East Texas State Univ., Commerce. Occupational Curriculum Lab.

This teacher's guide is part of an instructional series on small engine repair that is intended for use with mentally retarded and learning disabled students in general mechanical repair programs. Notes to the instructor cover equipment needed, preparation before teaching, and use of evaluation charts, transparency masters, audiovisual(s), and…

Safety Education Handbook. Volume 2.

ERIC Educational Resources Information Center

Kansas State Dept. of Education, Topeka.

This is the second of three volumes of a safety guide developed to assist Kansas administrators and teachers in organizing, evaluating, and maintaining safety programs. It provides information to help them identify, assess, and correct unsafe conditions relating to equipment and facilities and ensure a safe and healthy environment for themselves…

Enhancing extension recommendations to maximize efficacy of spray programs for the Georgia DOT : final report.

DOT National Transportation Integrated Search

2015-12-23

Research was conducted to evaluate equipment, adjuvants, and water quality used by the : Georgia DOT on herbicide efficacy for roadside management. From 19 DOT stations, 68% had alkaline : (7.1 to 7.9) water, 32% had hard water (>120 ppm), and 10% ha...

Handbook for Educational Buildings Planning. Educational Building and Equipment 9.

ERIC Educational Resources Information Center

Almeida, Rodolfo

Stages in the educational facility planning process are presented in this handbook, with a second focus on implementation. Four chapters provide information on the four cycles of the planning process, which include analysis and diagnosis, research and development, planning and programming, and implementation and evaluation. Characteristics of an…

Operation Of The X-29A Digital Flight-Control System

NASA Technical Reports Server (NTRS)

Chacon, Vince; Mcbride, David

1990-01-01

Report reviews program of testing and evaluation of digital flight-control system for X-29A airplane, with emphasis on operation during tests. Topics include design of system, special electronic testing equipment designed to aid in daily operations, and aspects of testing, including detection of faults.

Safety Education Handbook. Volume 3.

ERIC Educational Resources Information Center

Kansas State Dept. of Education, Topeka.

This is the third of three volumes of a safety guide developed to assist Kansas administrators and teachers in organizing, evaluating, and maintaining safety programs. It provides information to help them identify, assess, and correct unsafe conditions relating to equipment and facilities and ensure a safe and healthy environment for themselves…

30 CFR 282.23 - Testing Plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Testing Plan. 282.23 Section 282.23 Mineral... § 282.23 Testing Plan. All testing activities shall be conducted in accordance with a Testing Plan..., to carry out a pilot program to evaluate processing techniques or technology or mining equipment, or...

Technical Manual for Batteries, Navy Lithium Safety Program Responsibilities and Procedures

DTIC Science & Technology

2004-08-19

lithium ion batteries and all equipment powered by lithium electrochemical power source(s) through all phases of the life of such systems. The purpose of this manual is to establish safety guidelines for the selection, design, testing, evaluation, use, packaging, storage, transportation and disposal of lithium

Evaluation of spray droplet spectrum of sprayers used for vector control

USDA-ARS?s Scientific Manuscript database

Droplet spectra data were collected from spray equipment intended for use in vector control by the US Department of Defense pest management programs to determine if they produce droplets in the ultra-low volume (ULV) spectrum. Droplets generated by 26 sprayers utilizing water + non-ionic surfactant...

Feasibility of Helicopter Support Seek Frost.

DTIC Science & Technology

1980-05-01

the allowable maximum weight can be used as the payload. The payload is a variable. Small helicopters with full fuel and auxillary tanks can fly...equipment, that the program to obtain icing approval on the S-76 will be finalized for management evaluation, and a decision can be made at that time to

Reliability program requirements for aeronautical and space system contractors

NASA Technical Reports Server (NTRS)

1987-01-01

General reliability program requirements for NASA contracts involving the design, development, fabrication, test, and/or use of aeronautical and space systems including critical ground support equipment are prescribed. The reliability program requirements require (1) thorough planning and effective management of the reliability effort; (2) definition of the major reliability tasks and their place as an integral part of the design and development process; (3) planning and evaluating the reliability of the system and its elements (including effects of software interfaces) through a program of analysis, review, and test; and (4) timely status indication by formal documentation and other reporting to facilitate control of the reliability program.

Breaking out of the biomed box: an audit assessment and recommendations for an in-house biomedical engineering program.

PubMed

Dickey, David M; Jagiela, Steven; Fetters, Dennis

2003-01-01

In order to assess the current performance and to identify future growth opportunities of an in-house biomedical engineering (BME) program, senior management of Lehigh Valley Hospital (Allentown, Penn) engaged (in July 2001) the services of a clinical engineering consultant. Although the current in-house program was both functionally and financially sound, an independent audit had not been performed in over 4 years, and there were growing concerns by the BME staff related to the department's future leadership and long-term support from senior management. After an initial 2-month audit of the existing program, the consultant presented 41 separate recommendations for management's consideration. In order to refine and implement these recommendations, 5 separate committees were established to further evaluate a consolidated version of them, with the consultant acting as the facilitator for each group. Outcomes from each of the committees were used in the development of a formal business plan, which, upon full implementation, would not only strengthen and refine the current in-house service model but could also result in a substantial 3-year cost savings for the organization ($1,100,000 from existing operations, $500,000 in cost avoidance by in-sourcing postwarranty support of future capital equipment acquisitions). Another key outcome of the project was related to the development of a new master policy, titled the "Medical Equipment Management Program," complete with a newly defined state-of-the-art equipment scheduled inspection frequency model.

Evaluation of the Redesign of an Undergraduate Cell Biology Course

PubMed Central

McEwen, Laura April; Harris, dik; Schmid, Richard F.; Vogel, Jackie; Western, Tamara

2009-01-01

This article offers a case study of the evaluation of a redesigned and redeveloped laboratory-based cell biology course. The course was a compulsory element of the biology program, but the laboratory had become outdated and was inadequately equipped. With the support of a faculty-based teaching improvement project, the teaching team redesigned the course and re-equipped the laboratory, using a more learner-centered, constructivist approach. The focus of the article is on the project-supported evaluation of the redesign rather than the redesign per se. The evaluation involved aspects well beyond standard course assessments, including the gathering of self-reported data from the students concerning both the laboratory component and the technical skills associated with the course. The comparison of pre- and postdata gave valuable information to the teaching team on course design issues and skill acquisition. It is argued that the evaluation process was an effective use of the scarce resources of the teaching improvement project. PMID:19255138

Beyond "Classroom" Technology: The Equipment Circulation Program at Rasmuson Library, University of Alaska Fairbanks

ERIC Educational Resources Information Center

Jensen, Karen

2008-01-01

The library at the University of Alaska Fairbanks offers a unique equipment lending program through its Circulation Desk. The program features a wide array of equipment types, generous circulation policies, and unrestricted borrowing, enabling students, staff, and faculty to experiment with the latest in audio, video, and computer technologies,…

Operational evaluation of rapid diagnostic testing for Ebola Virus Disease in Guinean laboratories

PubMed Central

Aho, Josephine; Franklin, Kristyn; Likofata, Jacques; Kamgang, Jean Baptiste; Keita, Sakoba; Koivogui, Lamine; Magassouba, N’Faly; Martel, Lise D.; Dahourou, Anicet George

2017-01-01

Background Rapid Diagnostic Tests (RDTs) for Ebola Virus Disease (EVD) at the point of care have the potential to increase access and acceptability of EVD testing and the speed of patient isolation and secure burials for suspect cases. A pilot program for EVD RDTs in high risk areas of Guinea was introduced in October 2015. This paper presents concordance data between EVD RDTs and PCR testing in the field as well as an assessment of the acceptability, feasibility, and quality assurance of the RDT program. Methods and findings Concordance data were compiled from laboratory surveillance databases. The operational measures of the laboratory-based EVD RDT program were evaluated at all 34 sentinel sites in Guinea through: (1) a technical questionnaire filled by the lab technicians who performed the RDTs, (2) a checklist filled by the evaluator during the site visits, and (3) direct observation of the lab technicians performing the quality control test. Acceptability of the EVD RDT was good for technicians, patients, and families although many technicians (69.8%) expressed concern for their safety while performing the test. The feasibility of the program was good based on average technician knowledge scores (6.6 out of 8) but basic infrastructure, equipment, and supplies were lacking. There was much room for improvement in quality assurance of the program. Conclusions The implementation of new diagnostics in weak laboratory systems requires general training in quality assurance, biosafety and communication with patients in addition to specific training for the new test. Corresponding capacity building in terms of basic equipment and a long-term commitment to transfer supervision and quality improvement to national public health staff are necessary for successful implementation. PMID:29190713

Operational evaluation of rapid diagnostic testing for Ebola Virus Disease in Guinean laboratories.

PubMed

VanSteelandt, Amanda; Aho, Josephine; Franklin, Kristyn; Likofata, Jacques; Kamgang, Jean Baptiste; Keita, Sakoba; Koivogui, Lamine; Magassouba, N'Faly; Martel, Lise D; Dahourou, Anicet George

2017-01-01

Rapid Diagnostic Tests (RDTs) for Ebola Virus Disease (EVD) at the point of care have the potential to increase access and acceptability of EVD testing and the speed of patient isolation and secure burials for suspect cases. A pilot program for EVD RDTs in high risk areas of Guinea was introduced in October 2015. This paper presents concordance data between EVD RDTs and PCR testing in the field as well as an assessment of the acceptability, feasibility, and quality assurance of the RDT program. Concordance data were compiled from laboratory surveillance databases. The operational measures of the laboratory-based EVD RDT program were evaluated at all 34 sentinel sites in Guinea through: (1) a technical questionnaire filled by the lab technicians who performed the RDTs, (2) a checklist filled by the evaluator during the site visits, and (3) direct observation of the lab technicians performing the quality control test. Acceptability of the EVD RDT was good for technicians, patients, and families although many technicians (69.8%) expressed concern for their safety while performing the test. The feasibility of the program was good based on average technician knowledge scores (6.6 out of 8) but basic infrastructure, equipment, and supplies were lacking. There was much room for improvement in quality assurance of the program. The implementation of new diagnostics in weak laboratory systems requires general training in quality assurance, biosafety and communication with patients in addition to specific training for the new test. Corresponding capacity building in terms of basic equipment and a long-term commitment to transfer supervision and quality improvement to national public health staff are necessary for successful implementation.

Apollo experience report: Development flight instrumentation. [telemetry equipment for space flight test program

NASA Technical Reports Server (NTRS)

Farmer, N. B.

1974-01-01

Development flight instrumentation was delivered for 25 Apollo vehicles as Government-furnished equipment. The problems and philosophies of an activity that was concerned with supplying telemetry equipment to a space-flight test program are discussed. Equipment delivery dates, system-design details, and flight-performance information for each mission also are included.

Loch Vale Watershed Long-Term Ecological Research and Monitoring Program: Quality Assurance Report, 2003-09

USGS Publications Warehouse

Richer, Eric E.; Baron, Jill S.

2011-01-01

The Loch Vale watershed project is a long-term research and monitoring program located in Rocky Mountain National Park that addresses watershed-scale ecosystem processes, particularly as they respond to atmospheric deposition and climate variability. Measurements of precipitation depth, precipitation chemistry, discharge, and surface-water quality are made within the watershed and elsewhere in Rocky Mountain National Park. As data collected for the program are used by resource managers, scientists, policy makers, and students, it is important that all data collected in Loch Vale watershed meet high standards of quality. In this report, data quality was evaluated for precipitation, discharge, and surface-water chemistry measurements collected during 2003-09. Equipment upgrades were made at the Loch Vale National Atmospheric Deposition Program monitoring site to improve precipitation measurements and evaluate variability in precipitation depth and chemistry. Additional solar panels and batteries have been installed to improve the power supply, and data completeness, at the NADP site. As a result of equipment malfunction, discharge data for the Loch Outlet were estimated from October 18, 2005, to August 17, 2006. Quality-assurance results indicate that more than 98 percent of all surface-water chemistry measurements were accurate and precise. Records that did not meet quality criteria were removed from the database. Measurements of precipitation depth, precipitation chemistry, discharge, and surface-water quality were all sufficiently complete and consistent to support project data needs.

Delivering health information about self-medication to older adults: use of touchscreen-equipped notebook computers.

PubMed

Neafsey, P J; Strickler, Z; Shellman, J; Padula, A T

2001-11-01

Preventing Drug Interactions in Active Older Adults is an educational intervention to prevent prescription and over-the-counter (OTC) drug and alcohol interactions in active, community-living older adults. The objectives of the program are to increase older adults' knowledge of potential interactions of prescription medications with OTC drugs and alcohol and to increase their confidence (self-efficacy) about how to avoid such interactions. An interactive multimedia computer software program (Personal Education Program or PEP) was designed for the learning styles and psychomotor skills of older adults. Focus groups of older adults evaluated PEP components in a formative manner during development. The program content dealing with antacids, calcium supplements, and acid reducers was pilot tested with 60 older adults recruited from local senior centers. Participants used the PEP on notebook computers equipped with infrared-sensitive touchscreens. Users of PEP had greater knowledge and self-efficacy scores than controls. Participants indicated a high degree of satisfaction with the PEP and reported their intent to make specific changes in self-medication behaviors.

Mississippi Curriculum Framework for Vehicle and Mobile Equipment Mechanics (Program CIP: 47.0699--Vehicle and Mobile Equipment Mech.). Secondary Programs.

ERIC Educational Resources Information Center

Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

This document, which reflects Mississippi's statutory requirement that instructional programs be based on core curricula and performance-based assessment, contains outlines of the instructional units required in local instructional management plans and daily lesson plans for vehicle and mobile equipment mechanics I and II. Presented first are a…

Manual for ERLE (Energy-Related Laboratory Equipment). Instructions and information for institutions of higher learning concerning used energy-related laboratory equipment grants; Manual para ERLE [Equipo de Laboratorio Relacionado con la Energia]. Instrucciones e informacion para instituciones de educacion superior sobre subvenciones de equipo de laboratorio usado relacionado con la energia (in Spanish)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-10-01

This is a listing of energy related equipment available through the Energy-Related Laboratory Equipment Grant Program which grants used equipment to institutions of higher education for energy-related research. Information included is an overview of the program, how to apply for a grant of equipment, eligibility requirements, types of equipment available, and the costs for the institution.

Determination of the Crack Resistance Parameters at Equipment Nozzle Zones Under the Seismic Loads Via Finite Element Method

NASA Astrophysics Data System (ADS)

Kyrychok, Vladyslav; Torop, Vasyl

2018-03-01

The present paper is devoted to the problem of the assessment of probable crack growth at pressure vessel nozzles zone under the cyclic seismic loads. The approaches to creating distributed pipeline systems, connected to equipment are being proposed. The possibility of using in common different finite element program packages for accurate estimation of the strength of bonded pipelines and pressure vessels systems is shown and justified. The authors propose checking the danger of defects in nozzle domain, evaluate the residual life of the system, basing on the developed approach.

Greenbelt Homes Pilot Program. Summary of Building Envelope Retrofits, Planned HVAC Equipment Upgrades, and Energy Savings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiehagen, J.; Del Bianco, M.; Mallay, D.

2015-05-22

The U.S. Department of Energy Building America team Partnership for Home Innovation wrote a report on Phase 1 of the project that summarized a condition assessment of the homes and evaluated retrofit options within the constraints of the cooperative provided by GHI. Phase 2 was completed following monitoring in the 2013–2014 winter season; the results are summarized in this report. Phase 3 upgrades of heating equipment will be implemented in time for the 2014–2015 heating season and are not part of this report.

The effects of physical training without equipment on pain perception and balance in the elderly: A randomized controlled trial.

PubMed

Patti, Antonino; Bianco, Antonino; Karsten, Bettina; Montalto, Maria Alessandra; Battaglia, Giuseppe; Bellafiore, Marianna; Cassata, Daniela; Scoppa, Fabio; Paoli, Antonio; Iovane, Angelo; Messina, Giuseppe; Palma, Antonio

2017-01-01

Research supports a link between exercise and falls prevention in the older population. Our aims were to evaluate pain perception and balance skills in a group of elderly subjects and to examine the consequences of a standardized equipment-free exercise program intervention on these variables. The study utilized a randomized controlled trial method. 92 subjects were recruited from a rural Sicilian village (Resuttano, Sicily, Italy). Subjects were randomly split into two groups, an experimental group (EG; n = 49) and a control group (CG; n = 43). Qualified fitness instructors delivered the standardized physical exercise program for the EG whilst the CG did not receive this exercise intervention. The Berg Balance Scale and the Oswestry Disability Index were administered in both groups before (T0) and after the intervention (T1). At T1, the EG group significantly improvement in balance (p < 0.0001) and pain perception (p < 0.0001). No significant differences were found within the CG both in BBS and ODI, respectively. Our findings suggest that a 13-weeks standardized exercise equipment-free program is effective in improving balance and perception of pain in the elderly. This type of intervention can consequently provide a low cost strategy to counteract the rate of disability in elderly.

Personal Protective Equipment in Animal Research

PubMed Central

Villano, Jason S; Follo, Janet M; Chappell, Mark G; Jr, Morris T Collins

2017-01-01

The occupational health and safety program is an integral component of a comprehensive animal care and use program. It is important to mitigate the risk of exposures of animal care and research personnel to allergens and physical, chemical, radiologic, and biologic hazards during the conduct of various tasks. This need is especially true in infectious disease and biocontainment research. One aspect of the program is the provision of personal protective equipment (PPE). Commercially available PPE should be carefully evaluated based on their material composition and performance according to manufacturer data. To help institutions and end users by providing them guidance on choosing appropriate PPE, we here discuss the regulatory framework, device standards, and materials engineering for various PPE, including gloves, shoe covers, head caps, gowns, aprons, masks, hearing and eye protection devices, and respirators. Ultimately, the choice of appropriate PPE is based on the risk assessment, which should include consideration for personnel comfort, correct device fitting, and the containment level for the hazard used. PMID:28662749

A job safety program for construction workers designed to reduce the potential for occupational injury using tool box training sessions and computer-assisted biofeedback stress management techniques.

PubMed

Johnson, Kenneth A; Ruppe, Joan

2002-01-01

This project was conducted with a multicultural construction company in Hawaii, USA. The job duties performed included drywall and carpentry work. The following objectives were selected for this project: (a) fire prevention training and inspection of first aid equipment; (b) blood-borne pathogen training and risk evaluation; (c) ergonomic and risk evaluation intervention program; (d) electrical safety training and inspection program; (e) slips, trips, and falls safety training; (f) stress assessment and Personal Profile System; (g) safety and health program survey; (h) improving employee relations and morale by emphasizing spirituality; and (i) computer-assisted biofeedback stress management training. Results of the project indicated that observed safety hazards, reported injuries, and levels of perceived stress. were reduced for the majority of the population.

How Successful are U.S. Efforts to Build Capacity in Developing Countries? A Framework to Assess the Global Train and Equip 1206 Program

DTIC Science & Technology

2011-01-01

CARE INFRASTRUCTURE AND TRANSPORTATION INTERNATIONAL AFFAIRS LAW AND BUSINESS NATIONAL SECURITY POPULATION AND AGING PUBLIC SAFETY SCIENCE AND...Prevention—International cooperation—Evaluation. 5. Combined operations (Military science )—Evaluation. 6. United States—Military relations—Foreign...as well as to elicit informa- tion regarding assessment guidance and skills. 7 See Jennifer D. P. Moroney, Jefferson P. Marquis, Cathryn Quantic

Troubleshooting. Teacher's Guide and Student Activity Sheets. Small Engine Repair Series.

ERIC Educational Resources Information Center

Hill, Pamela

This teacher's guide is part of an instructional series on small engine repair that is intended for use with mentally retarded and learning disabled students in general mechanical repair programs. Notes to the instructor cover equipment needed, preparation before teaching, and use of evaluation charts, transparency masters, audiovisual(s), and…

Employability Skill Development in Work-Integrated Learning: Barriers and Best Practice

ERIC Educational Resources Information Center

Jackson, Denise

2015-01-01

Work-integrated learning (WIL) is widely considered instrumental in equipping new graduates with the required employability skills to function effectively in the work environment. Evaluation of WIL programs in enhancing skill development remains predominantly outcomes-focused with little attention to the process of what, how and from whom students…

SCHOOL SAFETY EDUCATION CHECKLIST--ADMINISTRATION, INSTRUCTION, PROTECTION.

ERIC Educational Resources Information Center

National Education Association, Washington, DC.

THIS CHECKLIST IS AN EVALUATIVE TOOL FOR PLANNING PROGRAM IMPROVEMENT. PURPOSING TO STIMULATE THOUGHT AND ACTION ON PROBLEMS OF SAFETY EDUCATION IN SCHOOLS, IT IS DESIGNED TO ENCOURAGE INSPECTIONS OF SCHOOL BUILDINGS FOR (1) SAFE CONDITIONS OF STRUCTURES, GROUNDS, AND EQUIPMENT, (2) SAFE PRACTICES, AND (3) OPTIMUM USE OF THESE SAFE PRACTICES IN…

Evaluation of the localization auditory screening test in children 6-18 months of age.

PubMed

Tillis, C H; Grimm, W A

1978-01-01

The present paper is a report of a project to develop an automated auditory screening test for infants six to 18 months of age. The first year of the project was devoted to developing equipment and test procedures; the second year was concerned with testing the effectiveness of the equipment and procedures on an actual population of six to 18 month old infants. Two-hundred and fifty infants were screened auditorily as part of a county health department child development clinic. The pass/fail results of the screening test were evaluated in terms of physical and developmental examination following the screening and by means of a case review of the child's previous history. The results indicate that the procedure under investigation can be used to differentiate the normal hearing infant from the infant with possible hearing problems. It is shown by the test environment in which this study was conducted that the procedure reported can be successfully incorporated into a public health program, i.e., child development clinics or EPSDT programs.

Improved ultrasonic standard reference blocks

NASA Technical Reports Server (NTRS)

Eitzen, D. G.; Sushinsky, G. F.; Chwirut, D. J.; Bechtoldt, C. J.; Ruff, A. W.

1976-01-01

A program to improve the quality, reproducibility and reliability of nondestructive testing through the development of improved ASTM-type ultrasonic reference standards is described. Reference blocks of aluminum, steel, and titanium alloys are to be considered. Equipment representing the state-of-the-art in laboratory and field ultrasonic equipment was obtained and evaluated. RF and spectral data on ten sets of ultrasonic reference blocks have been taken as part of a task to quantify the variability in response from nominally identical blocks. Techniques for residual stress, preferred orientation, and micro-structural measurements were refined and are applied to a reference block rejected by the manufacturer during fabrication in order to evaluate the effect of metallurgical condition on block response. New fabrication techniques for reference blocks are discussed and ASTM activities are summarized.

TRICARE program; clarification of benefit coverage of durable equipment and ordering or prescribing durable equipment; clarification of benefit coverage of assistive technology devises under the Extended Care Health Option Program. Final rule.

PubMed

2014-12-31

This final rule modifies the TRICARE regulation to add a definition of assistive technology (AT) devices for purposes of benefit coverage under the TRICARE Extended Care Health Option (ECHO) Program and to amend the definitions of durable equipment (DE) and durable medical equipment (DME) to better conform the language in the regulation to the statute. The final rule amends the language that specifically limits ordering or prescribing of DME to only a physician under the Basic Program, as this amendment will allow certain other TRICARE authorized individual professional providers, acting within the scope of their licensure, to order or prescribe DME. This final rule also incorporates a policy clarification relating to luxury, deluxe, or immaterial features of equipment or devices. That is, TRICARE cannot reimburse for the luxury, deluxe, or immaterial features of equipment or devices, but can reimburse for the base or basic equipment or device that meet the beneficiary's needs. Beneficiaries may choose to pay the provider for the luxury, deluxe, or immaterial features if they desire their equipment or device to have these "extra features."

Adolescent bariatric surgery program characteristics: the Teen Longitudinal Assessment of Bariatric Surgery (Teen-LABS) study experience.

PubMed

Michalsky, Marc P; Inge, Thomas H; Teich, Steven; Eneli, Ihuoma; Miller, Rosemary; Brandt, Mary L; Helmrath, Michael; Harmon, Carroll M; Zeller, Meg H; Jenkins, Todd M; Courcoulas, Anita; Buncher, Ralph C

2014-02-01

The number of adolescents undergoing weight loss surgery (WLS) has increased in response to the increasing prevalence of severe childhood obesity. Adolescents undergoing WLS require unique support, which may differ from adult programs. The aim of this study was to describe institutional and programmatic characteristics of centers participating in Teen Longitudinal Assessment of Bariatric Surgery (Teen-LABS), a prospective study investigating safety and efficacy of adolescent WLS. Data were obtained from the Teen-LABS database, and site survey completed by Teen-LABS investigators. The survey queried (1) institutional characteristics, (2) multidisciplinary team composition, (3) clinical program characteristics, and (4) clinical research infrastructure. All centers had extensive multidisciplinary involvement in the assessment, pre-operative education, and post-operative management of adolescents undergoing WLS. Eligibility criteria and pre-operative clinical and diagnostic evaluations were similar between programs. All programs have well-developed clinical research infrastructure, use adolescent-specific educational resources, and maintain specialty equipment, including high weight capacity diagnostic imaging equipment. The composition of clinical team and institutional resources is consistent with current clinical practice guidelines. These characteristics, coupled with dedicated research staff, have facilitated enrollment of 242 participants into Teen-LABS. © 2013 Published by Elsevier Inc.

Adolescent Bariatric Surgery Program Characteristics: The Teen Longitudinal Assessment of Bariatric Surgery (Teen-LABS) Study Experience

PubMed Central

Michalsky, M.P.; Inge, T.H.; Teich, S.; Eneli, I.; Miller, R.; Brandt, M.L.; Helmrath, M.; Harmon, C.M.; Zeller, M.H.; Jenkins, T.M.; Courcoulas, A.; Buncher, C.R.

2013-01-01

Background The number of adolescents undergoing weight loss surgery (WLS) has increased in response to the increasing prevalence of severe childhood obesity. Adolescents undergoing WLS require unique support, which may differ from adult programs. The aim of this study was to describe institutional and programmatic characteristics of centers participating in Teen-Longitudinal Assessment of Bariatric Surgery (Teen-LABS), a prospective study investigating safety and efficacy of adolescent WLS. Methods Data were obtained from the Teen-LABS database and site survey completed by Teen-LABS investigators. The survey queried (1) institutional characteristics, (2) multidisciplinary team composition, (3) clinical program characteristics, and (4) clinical research infrastructure. Results All centers had extensive multidisciplinary involvement in the assessment, preoperative education and post-operative management of adolescents undergoing WLS. Eligibility criteria, pre-operative clinical and diagnostic evaluations were similar between programs. All programs have well developed clinical research infrastructure, use adolescent-specific educational resources, and maintain specialty equipment, including high weight capacity diagnostic imaging equipment. Conclusions The composition of clinical team and institutional resources are consistent with current clinical practice guidelines. These characteristics, coupled with dedicated research staff, have facilitated enrollment of 242 participants into Teen-LABS. PMID:24491361

PM Program Prevents Early AM Repairs

ERIC Educational Resources Information Center

McRae, David

1974-01-01

Discusses how to initiate a preventive maintenance (PM) program: (1) make inventory of equipment that needs a PM program; (2) gather data about each piece of equipment; and (3) set maintenance goals. (Author/PG)

The robotized workstation "MASTER" for users with tetraplegia: description and evaluation.

PubMed

Busnel, M; Cammoun, R; Coulon-Lauture, F; Détriché, J M; Le Claire, G; Lesigne, B

1999-07-01

The rehabilitation robotics MASTER program was developed by the French Atomic Energy Commission (CEA) and evaluated by the APPROCHE Rehabilitation centers. The aim of this program is to increase the autonomy and quality of life of persons with tetraplegia in domestic and vocational environments. Taking advantage of its experience in nuclear robotics, the CEA has supported studies dealing with the use of such technical aids in the medical area since 1975 with the SPARTACUS project, followed by MASTER 10 years later, and its European extension in the framework of the TIDE/RAID program. The present system is composed of a fixed robotized workstation that includes a six-axis SCARA robot mounted on a rail to allow horizontal movement and is equipped with tools for various tasks. The Operator Interface (OI) has been carefully adapted to the most severe tetraplegia. Results are given following a 2-year evaluation in real-life situations.

Joint Air-to-Surface Standoff Missile (JASSM)

DTIC Science & Technology

2015-12-01

6.1.3) All Ops All Ops Joint Critical Ops All Ops All Ops Missile Reliability (KSA) (CPD para 6.2.8) 4th Lot .91 4th Lot .91 IOT &E .80 4th Lot .85 IOT &E...the ORD 303-95-III dated January 20, 2004 Change Explanations None Acronyms and Abbreviations IOT &E - Initial Operational Test and Evaluation KSA... Actuator Control Card, Lots 12 and 4 Systems Engineering Program Support/Program Tooling and Test Equipment, and JASSM-ER Standard Data Protocol (DS

Evaluations of in-use emission factors from off-road construction equipment

NASA Astrophysics Data System (ADS)

Cao, Tanfeng; Durbin, Thomas D.; Russell, Robert L.; Cocker, David R.; Scora, George; Maldonado, Hector; Johnson, Kent C.

2016-12-01

Gaseous and particle emissions from construction engines contribute an important fraction of the total air pollutants released into the atmosphere and are gaining increasing regulatory attention. Robust quantification of nitrogen oxides (NOx) and particulate matter (PM) emissions are necessary to inventory the contribution of construction equipment to atmospheric loadings. Theses emission inventories require emissions factors from construction equipment as a function of equipment type and modes of operation. While the development of portable emissions measurement systems (PEMS) has led to increased studies of construction equipment emissions, emissions data are still much more limited than for on-road vehicles. The goal of this research program was to obtain accurate in-use emissions data from a test fleet of newer construction equipment (model year 2002 or later) using a Code of Federal Requirements (CFR) compliant PEMS system. In-use emission measurements were made from twenty-seven pieces of construction equipment, which included four backhoes, six wheel loaders, four excavators, two scrapers (one with two engines), six bulldozers, and four graders. The engines ranged in model year from 2003 to 2012, in rated horsepower (hp) from 92 to 540 hp, and in hours of operation from 24 to 17,149 h. This is the largest study of off-road equipment emissions using 40 CFR part 1065 compliant PEMS equipment for all regulated gaseous and particulate emissions.

Professional Equipment for a University Environmental Health Program

ERIC Educational Resources Information Center

Iglar, Albert F.; Morgan, Monroe T.

1972-01-01

A rather thorough description of the professional equipment utilized in the Environmental Health Program at East Tennessee State University. Describes equipment and apparatus employed in the General Environmental, Occupational Health and Safety, and the Air and Water Pollution Control Areas. Table of recommended basic professional equipment…

Updated operational protocols for the U.S. Geological Survey Precipitation Chemistry Quality Assurance Project in support of the National Atmospheric Deposition Program

USGS Publications Warehouse

Wetherbee, Gregory A.; Martin, RoseAnn

2017-02-06

The U.S. Geological Survey Branch of Quality Systems operates the Precipitation Chemistry Quality Assurance Project (PCQA) for the National Atmospheric Deposition Program/National Trends Network (NADP/NTN) and National Atmospheric Deposition Program/Mercury Deposition Network (NADP/MDN). Since 1978, various programs have been implemented by the PCQA to estimate data variability and bias contributed by changing protocols, equipment, and sample submission schemes within NADP networks. These programs independently measure the field and laboratory components which contribute to the overall variability of NADP wet-deposition chemistry and precipitation depth measurements. The PCQA evaluates the quality of analyte-specific chemical analyses from the two, currently (2016) contracted NADP laboratories, Central Analytical Laboratory and Mercury Analytical Laboratory, by comparing laboratory performance among participating national and international laboratories. Sample contamination and stability are evaluated for NTN and MDN by using externally field-processed blank samples provided by the Branch of Quality Systems. A colocated sampler program evaluates the overall variability of NTN measurements and bias between dissimilar precipitation gages and sample collectors.This report documents historical PCQA operations and general procedures for each of the external quality-assurance programs from 2007 to 2016.

Prioritizing equipment for replacement.

PubMed

Capuano, Mike

2010-01-01

It is suggested that clinical engineers take the lead in formulating evaluation processes to recommend equipment replacement. Their skill, knowledge, and experience, combined with access to equipment databases, make them a logical choice. Based on ideas from Fennigkoh's scheme, elements such as age, vendor support, accumulated maintenance cost, and function/risk were used.6 Other more subjective criteria such as cost benefits and efficacy of newer technology were not used. The element of downtime was also omitted due to the data element not being available. The resulting Periop Master Equipment List and its rationale was presented to the Perioperative Services Program Council. They deemed the criteria to be robust and provided overwhelming acceptance of the list. It was quickly put to use to estimate required capital funding, justify items already thought to need replacement, and identify high-priority ranked items for replacement. Incorporating prioritization criteria into an existing equipment database would be ideal. Some commercially available systems do have the basic elements of this. Maintaining replacement data can be labor-intensive regardless of the method used. There is usually little time to perform the tasks necessary for prioritizing equipment. However, where appropriate, a clinical engineering department might be able to conduct such an exercise as shown in the following case study.

Homer City Multistream Coal Cleaning Demonstration: A progress report. Report for January 1979-July 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carey, D.W.; Higgins, S.T.; Slowik, A.A.

1984-08-01

The report gives an overview of ongoing testing and evaluation of the Homer City Coal Cleaning Plant, built to enable the Homer City Power Complex to meet sulfur dioxide (SO2) emission levels mandated by the State of Pennsylvania and the U.S. Government. The plant was constructed as a result of an extensive comparative evaluation of flue gas desulfurization (FGD) and physical coal cleaning. The Homer City System, the Multistream Coal Cleaning System (MCCS), was chosen as an economical alternative to FGD. The plant contains circuits for cleaning coarse, medium, and fine coals and for recovering fine and very fine coals.more » The dominant type of cleaning equipment used in the plant is the dense medium cyclone. The original '93 plant' configuration was never able to clean coal to the conditions specified in the plant design. An extensive test and evaluation program was begun to identify and correct the causes of plant operating problems. After extensive pilot plant equipment tests and engineering studies were completed, recommendations were made for plant modifications necessary to correct the design and operating deficiencies of the plant. Extensive modifications were made to one of two parallel processing trains in the plant (the 'B' circuits), and a test program was initiated to evaluate these corrective measures. The modified 'B' circuits have not yet met design conditions.« less

78 FR 26544 - Energy Efficiency Program for Commercial and Industrial Equipment: Public Meeting and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-07

... Efficiency Program for Commercial and Industrial Equipment: Public Meeting and Availability of the Framework... the development of energy conservation standards for commercial and industrial fan and blower equipment published on February 1, 2013, is extended to June 3, 2013. DATES: The comment period for the...

78 FR 12251 - Energy Efficiency Program for Commercial and Industrial Equipment: Public Meeting and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-22

... Efficiency Program for Commercial and Industrial Equipment: Public Meeting and Availability of the Framework... the notice of public meeting and availability of the Framework Document pertaining to the development of energy conservation standards for commercial and industrial fan and blower equipment published on...

Curriculum development of 6for6: Longitudinal research skills program for rural and remote family physicians.

PubMed

McCarthy, Patti; Bethune, Cheri; Fitzgerald, Shari; Graham, Wendy; Asghari, Shabnam; Heeley, Thomas; Godwin, Marshall

2016-02-01

To address barriers challenging the engagement of rural and remote family physicians (RRFPs) in research, Memorial University of Newfoundland in St John's has developed a longitudinal faculty development program (FDP) called 6for6. To establish and evaluate a longitudinal FDP that promotes a foundation of research activity. Program description Informed by a needs assessment in phase 1, phase 2 saw the 6for6 curriculum designed, developed, and implemented to reflect the unique needs of RRFPs. Preliminary evaluations have been conducted and results will be presented after year 1 of the program. The 6for6 FDP has been positively received by participants, and it is evident that they will serve as champions of rural research capacity building. It is anticipated that by April 2017, 18 RRFPs will be equipped with the research and leadership skills required to foster research networks within and outside their communities.

A Management Information System Model for Program Management. Ph.D. Thesis - Oklahoma State Univ.; [Computerized Systems Analysis

NASA Technical Reports Server (NTRS)

Shipman, D. L.

1972-01-01

The development of a model to simulate the information system of a program management type of organization is reported. The model statistically determines the following parameters: type of messages, destinations, delivery durations, type processing, processing durations, communication channels, outgoing messages, and priorites. The total management information system of the program management organization is considered, including formal and informal information flows and both facilities and equipment. The model is written in General Purpose System Simulation 2 computer programming language for use on the Univac 1108, Executive 8 computer. The model is simulated on a daily basis and collects queue and resource utilization statistics for each decision point. The statistics are then used by management to evaluate proposed resource allocations, to evaluate proposed changes to the system, and to identify potential problem areas. The model employs both empirical and theoretical distributions which are adjusted to simulate the information flow being studied.

Materiel Acquisition Management Guide

DTIC Science & Technology

1980-02-11

Ii-n manager and his staff, hiqhlighted by the specific de - tails provided in tabbea one-sheet descriptions. • Part III - Areas of Aco-uisition...support program requirements? Support and Test Equipment (S/TE)? Spares Support (SS)? Storage and transportation ? training? o Have test and...PACKAGES PROCUREMENT PLANNING/ PROCUREMENT pLANS TEST AND EVALUATION - PLANNING PRODUCIBILITY ENGINEERING AND TRAINING PLANNING (PEP) TRANSPORTABILITY

The Impact of Mindfulness Education on Elementary School Students: Evaluation of the "Master Mind" Program

ERIC Educational Resources Information Center

Parker, Alison E.; Kupersmidt, Janis B.; Mathis, Erin T.; Scull, Tracy M.; Sims, Calvin

2014-01-01

Children need to be equipped with the skills to respond effectively to stress and prevent poor decision-making surrounding alcohol and tobacco use. Training and practice in mindfulness is one possible avenue for building children's skills. Recent research has revealed that mindfulness education in the classroom may play a role in enhancing…

Impact of low cost refurbishable and standard spacecraft upon future NASA space programs. Payload effects follow-on study, appendix

NASA Technical Reports Server (NTRS)

1972-01-01

Mission analysis is discussed, including the consolidation and expansion of mission equipment and experiment characteristics, and determination of simplified shuttle flight schedule. Parametric analysis of standard space hardware and preliminary shuttle/payload constraints analysis are evaluated, along with the cost impact of low cost standard hardware.

Defense Systems Modernization and Sustainment Initiative

DTIC Science & Technology

2014-03-31

research programs focus on sustainable production, sustainable energy, sustainable mobility , and ecologically friendly information technology systems...for Sustainable Mobility (CSM): focused on developing viable technologies for sustainable transportation systems and the support of complex equipment...utilization of mobile devices. The objective of the evaluation was to identify features that the new implementation of LEEDS would require, such as

Is American Teacher Education Fully up to the Common Core Requirements?

ERIC Educational Resources Information Center

Murray, Frank B.

2014-01-01

This narrative considers how well equipped today's teacher education students and faculty are to meet the demands of the new Common Core State Standards. Data from the Teacher Education Accreditation Council's national evaluation of teacher education programs gives a mixed picture that, while mostly encouraging, also reveals that some…

Evaluation of Hybrid Learning in a Construction Engineering Context: A Mixed-Method Approach

ERIC Educational Resources Information Center

Karabulut-Ilgu, Aliye; Jahren, Charles

2016-01-01

Engineering educators call for a widespread implementation of hybrid learning to respond to rapidly changing demands of the 21st century. In response to this call, a junior-level course in the Construction Engineering program entitled Construction Equipment and Heavy Construction Methods was converted into a hybrid learning model. The overarching…

Flight evaluation results from the general-aviation advanced avionics system program

NASA Technical Reports Server (NTRS)

Callas, G. P.; Denery, D. G.; Hardy, G. H.; Nedell, B. F.

1983-01-01

A demonstration advanced avionics system (DAAS) for general-aviation aircraft was tested at NASA Ames Research Center to provide information required for the design of reliable, low-cost, advanced avionics systems which would make general-aviation operations safer and more practicable. Guest pilots flew a DAAS-equipped NASA Cessna 402-B aircraft to evaluate the usefulness of data busing, distributed microprocessors, and shared electronic displays, and to provide data on the DAAS pilot/system interface for the design of future integrated avionics systems. Evaluation results indicate that the DAAS hardware and functional capability meet the program objective. Most pilots felt that the DAAS representative of the way avionics systems would evolve and felt the added capability would improve the safety and practicability of general-aviation operations. Flight-evaluation results compiled from questionnaires are presented, the results of the debriefings are summarized. General conclusions of the flight evaluation are included.

Site operator program final report for fiscal years 1992 through 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Francfort, J.E.; Bassett, R.R.; Birasco, S.

The Site Operator Program was an electric vehicle testing and evaluation program sponsored by US Department of Energy and managed at the Idaho National Engineering and Environmental Laboratory. The Program`s goals included the field evaluation of electric vehicles in real-world applications and environments; the support of electric vehicle technology advancement; the development of infrastructure elements necessary to support significant electric vehicle use; and increasing the awareness and acceptance of electric vehicles. This report covers Program activities from 1992 to 1996. The Site Operator Program ended in September 1996, when it was superseded by the Field Operations Program. Electric vehicle testingmore » included baseline performance testing, which was performed in conjunction with EV America. The baseline performance parameters included acceleration, braking, range, energy efficiency, and charging time. The Program collected fleet operations data on electric vehicles operated by the Program`s thirteen partners, comprising electric utilities, universities, and federal agencies. The Program`s partners had over 250 electric vehicles, from vehicle converters and original equipment manufacturers, in their operating fleets. Test results are available via the World Wide Web site at http://ev.inel.gov/sop.« less

The Community Research Scholars Initiative: A Mid‐Project Assessment

PubMed Central

Pike, Earl; Sehgal, Ashwini R.; Fischer, Robert L.; Collins, Cyleste

2015-01-01

Abstract Community organizations addressing health and human service needs generally have minimal capacity for research and evaluation. As a result, they are often inadequately equipped to independently carry out activities that can be critical for their own success, such as conducting needs assessments, identifying best practices, and evaluating outcomes. Moreover, they are unable to develop equitable partnerships with academic researchers to conduct community‐based research. This paper reports on the progress of the Community Research Scholar Initiative (CRSI), a program that aims to enhance community research and evaluation capacity through training of selected employees from Greater Cleveland community organizations. The intensive 2‐year CRSI program includes didactic instruction, fieldwork, multiple levels of community and academic engagement, leadership training, and a mentored research project. The first cohort of CRSI Scholars, their community organizations, and other community stakeholders have incorporated program lessons into their practices and operations. The CRSI program evaluation indicates: the importance of careful Scholar selection; the need to engage executive leadership from Scholar organizations; the value of a curriculum integrating classwork, fieldwork, and community engagement; and the need for continual scholar skill and knowledge assessment. These findings and lessons learned guide other efforts to enhance community organization research and evaluation capacity. PMID:26073663

Investigation of a family of power conditioners integrated into a utility grid: final report Category I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, P.; Putkovich, R.P.

1981-07-01

A study was conducted of the requirements for and technologies applicable to power conditioning equipment in residential solar photovoltaic systems. A survey of companies known or thought to manufacture power conditioning equipment was conducted to asses the technology. Technical issues regarding ac and dc interface requirements were studied. A baseline design was selected to be a good example of existing technology which would not need significant development effort for its implementation. Alternative technologies are evaluated to determine which meet the baseline specification, and their costs and losses are evaluated. Areas in which cost improvements can be obtained are studied, andmore » the three best candidate technologies--the current-sourced converter, the HF front end converter, and the programmed wave converter--are compared. It is concluded that the designs investigated will meet, or with slight improvement could meet, short term efficiency goals. Long term efficiency goals could be met if an isolation transformer were not required in the power conditioning equipment. None of the technologies studied can meet cost goals unless further improvements are possible. (LEW)« less

76 FR 38287 - Energy Conservation Program: Certification, Compliance, and Enforcement for Consumer Products and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-30

... commercial refrigeration equipment; commercial heating, ventilating, air- conditioning (HVAC) equipment..., manufacturers of commercial refrigeration equipment; commercial HVAC equipment; commercial WH equipment; walk-in... extension to the compliance date for the certification provisions for commercial refrigeration equipment...

West Valley feasibility study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pirro, J.

This report presents the results of a technical assessment of decontamination alternative prepared for the Western New York Nuclear Service Center (WNYNSC). The purpose of the assessment is to determine the recommended method for decontamination of cell surfaces and decontamination and removal of fuel reprocessing cell equipment to permit manual entry into the cells for the installation of waste solidification equipment. The primary cells of interest are the PMC, GPC, and CPC because they offer the largest usable volume for the solidification program. The secondary cells include XC-1, XC-2, XC-3 and the PPC which may be needed to support themore » solidification program. Five decontamination assessments were evaluated (A-E). The assessments included the estimated cost, occupational exposure, duration, manpower, waste volume generated, and final cell radiation levels achieved with the alternative decontamination methods. The methods varied from thorough destructive decontamination to equipment removal without decontamination followed by cell wall and floor decontamination. The recommended method for the primary cells is to utilize the remote manipulators and cranes to the maximum extent possible to decontaminate equipment and cell surfaces remotely, and to remove the equipment for temporary on-site storage. The recommended method for secondary cell decontamination is to remotely decontaminate the cells to the maximum extent possible prior to manned entry for contact-removal of the fuel reprocessing equipment (Assessment D). Assessment A is expected to cost $8,713,500 in 1980 dollars (including a 25% contingency) and will result in an occupational exposure of 180.3 manRem. Assessment D is expected to cost $11,039,800 and will result in an occupational exposure of 259 manRems.« less

Life sciences payload definition and integration study. Volume 2: Requirements, design, and planning studies for the carry-on laboratories. [for Spacelab

NASA Technical Reports Server (NTRS)

1974-01-01

The task phase concerned with the requirements, design, and planning studies for the carry-on laboratory (COL) began with a definition of biomedical research areas and candidate research equipment, and then went on to develop conceptual layouts for COL which were each evaluated in order to arrive at a final conceptual design. Each step in this design/evaluation process concerned itself with man/systems integration research and hardware, and life support and protective systems research and equipment selection. COL integration studies were also conducted and include attention to electrical power and data management requirements, operational considerations, and shuttle/Spacelab interface specifications. A COL program schedule was compiled, and a cost analysis was finalized which takes into account work breakdown, annual funding, and cost reduction guidelines.

Welding, Bonding and Fastening, 1984

NASA Technical Reports Server (NTRS)

Buckley, J. D. (Editor); Stein, B. A. (Editor)

1985-01-01

A compilation of papers presented in a joint NASA, American Society for Metals, The George Washington University, American Welding Soceity, and Society of Manufacturing Engineers conference on Welding, Bonding, and Fastening at Langley Research Center, Hampton, VA, on October 23 to 25, 1984 is given. Papers were presented on technology developed in current research programs relevant to welding, bonding, and fastening of structural materials required in fabricating structures and mechanical systems used in the aerospace, hydrospace, and automotive industries. Topics covered in the conference included equipment, hardware and materials used when welding, brazing, and soldering, mechanical fastening, explosive welding, use of unique selected joining techniques, adhesives bonding, and nondestructive evaluation. A concept of the factory of the future was presented, followed by advanced welding techniques, automated equipment for welding, welding in a cryogenic atmosphere, blind fastening, stress corrosion resistant fasteners, fastening equipment, explosive welding of different configurations and materials, solid-state bonding, electron beam welding, new adhesives, effects of cryogenics on adhesives, and new techniques and equipment for adhesive bonding.

A simple approach to industrial laser safety.

PubMed

Lewandowski, Michael A; Hinz, Michael W

2005-02-01

Industrial applications of lasers include marking, welding, cutting, and other material processing. Lasers used in these ways have significant power output but are generally designed to limit operator exposure to direct or scattered laser radiation to harmless levels in order to meet the Federal Laser Product Performance Standard (21CFR1040) for Class 1 laser products. Interesting challenges occur when companies integrate high power lasers into manufacturing or process control equipment. A significant part of the integration process is developing engineering and administrative controls to produce an acceptable level of laser safety while balancing production, maintenance, and service requirements. 3M Company uses a large number of high power lasers in numerous manufacturing processes. Whether the laser is purchased as a Class 1 laser product or whether it is purchased as a Class 4 laser and then integrated into a manufacturing application, 3M Company has developed an industrial laser safety program that maintains a high degree of laser safety while facilitating the rapid and economical integration of laser technology into the manufacturing workplace. This laser safety program is based on the requirements and recommendations contained in the American National Standard for Safe Use of Lasers, ANSI Z136.1. The fundamental components of the 3M program include hazard evaluation, engineering, administrative, and procedural controls, protective equipment, signs and labels, training, and re-evaluation upon change. This program is implemented in manufacturing facilities and has resulted in an excellent history of laser safety and an effective and efficient use of laser safety resources.

The estimation of electrical cable fire-induced damage limits

NASA Astrophysics Data System (ADS)

Nowlen, S. P.; Jacobus, M. J.

Sandia National Laboratories has, for several years, been engaged in the performance of both fire safety and electrical equipment qualification research under independent programs sponsored by the US Nuclear Regulatory Commission. Recent comparisons between electrical cable thermal damageability data gathered independently in these two efforts indicate that a direct correlation exists between certain of the recent cable thermal vulnerability information gathered under equipment qualification conditions and thermal damageability in a fire environment. This direct correlation allows for a significant expansion of the data base on estimated cable thermal vulnerability limits in a fire environment because of the wide range of cable types and products that have been evaluated as a part of the equipment qualification research. This paper provides a discussion of the basis for the derived correlation, and presents estimated cable thermal damage limits for a wide range of generic cable types and specific cable products. The supposition that a direct correlation exists is supported through direct comparisons of the test results for certain specific cable products. The proposed supplemental cable fire vulnerability data gained from examination of the equipment qualification results is presented. These results should be of particular interest to those engaged in the evaluation of fire risk for industrial facilities, including nuclear power plants.

Time-related degradation, a key issue in nuclear plant safety evaluations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonzon, L.L.; Bustard, L.D.; Clough, R.L.

1982-01-01

Sandia National Laboratories is conducting a number of programs under NRC sponsorship which deal with safety-related equipment qualification issues, including the important aspect of aging. Among these is the Qualification Testing Evaluation (QTE) program which was probably the first to devote significant effort towards aging research and was one of the primary motivators leading to the Workshop. The thrust of the QTE aging efforts has been on elastomeric materials, typically used in electrical cables, seals, gaskets, and the like; currently, efforts are being pursued on plant ambient environments measurements, aging of electronics, and aging of motors. A brief status reportmore » is presented in this paper.« less

Application of solar energy; Proceedings of the Third Southeastern Conference, Huntsville, Ala., April 17-19, 1978

NASA Technical Reports Server (NTRS)

Wu, S. T. (Editor); Christensen, D. L.; Head, R. R.

1978-01-01

Demonstration projects, systems-subsystems simulation programs, applications (heating, cooling, agricultural, industrial), and climatic data testing (standards, economics, institutional) are the topics of the book. Economics of preheating water for commercial use and collecting, processing, and dissemination of data for the national demonstration program are discussed. Computer simulation of a solar energy system and graphical representation of solar collector performance are considered. Attention is given to solar driven heat pumps, solar cooling equipment, hybrid passive/active solar systems, and solar farm buildings. Evaluation of a thermographic scanning device for solar energy and conservation applications, use of meteorological data in system evaluation, and biomass conversion potential are presented.

Development and evaluation of a multifaceted ergonomics program to prevent injuries associated with patient handling tasks.

PubMed

Nelson, Audrey; Matz, Mary; Chen, Fangfei; Siddharthan, Kris; Lloyd, John; Fragala, Guy

2006-08-01

Nurses have one of the highest rates of work-related musculoskeletal injury of any profession. Over the past 30 years, efforts to reduce work-related musculoskeletal disorders in nurses have been largely unsuccessful. The primary goal of this program was to create safer working environments for nursing staff who provide direct patient care. Our first objective was to design and implement a multifaceted program that successfully integrated evidence-based practice, technology, and safety improvement. The second objective was to evaluate the impact of the program on injury rate, lost and modified work days, job satisfaction, self-reported unsafe patient handling acts, level of support for program, staff and patient acceptance, program effectiveness, costs, and return on investment. The intervention included six program elements: (1) Ergonomic Assessment Protocol, (2) Patient Handling Assessment Criteria and Decision Algorithms, (3) Peer Leader role, "Back Injury Resource Nurses", (4) State-of-the-art Equipment, (5) After Action Reviews, and (6) No Lift Policy. A pre-/post design without a control group was used to evaluate the effectiveness of a patient care ergonomics program on 23 high risk units (19 nursing home care units and 4 spinal cord injury units) in 7 facilities. Injury rates, lost work days, modified work days, job satisfaction, staff , and patient acceptance, program effectiveness, and program costs/savings were compared over two nine month periods: pre-intervention (May 2001-January 2002) and post-intervention (March 2002-November 2002). Data were collected prospectively through surveys, weekly process logs, injury logs, and cost logs. The program elements resulted in a statistically significant decrease in the rate of musculoskeletal injuries as well as the number of modified duty days taken per injury. While the total number of lost workdays decreased by 18% post-intervention, this difference was not statistically significant. There were statistically significant increases in two subscales of job satisfaction: professional status and tasks requirements. Self-reports by nursing staff revealed a statistically significant decrease in the number of 'unsafe' patient handling practices performed daily. Nurses ranked program elements they deemed to be "extremely effective": equipment was rated as most effective (96%), followed by No Lift Policy (68%), peer leader education program (66%), ergonomic assessment protocol (59%), patient handling assessment criteria and decision algorithms (55%), and lastly after action reviews (41%). Perceived support and interest for the program started at a high level for managers and nursing staff and remained very high throughout the program implementation. Patient acceptance was moderate when the program started but increased to very high by the end of the program. Although the ease and success of program implementation initially varied between and within the facilities, after six months there was strong evidence of support at all levels. The initial capital investment for patient handling equipment was recovered in approximately 3.75 years based on annual post-intervention savings of over $200,000/year in workers' compensation expenses and cost savings associated with reduced lost and modified work days and worker compensation. This multi-faceted program resulted in an overall lower injury rate, fewer modified duty days taken per injury, and significant cost savings. The program was well accepted by patients, nursing staff, and administrators. Given the significant increases in two job satisfaction subscales (professional status and task requirements), it is possible that nurse recruitment and retention could be positively impacted.

An Evaluation Method of Equipment Reliability Configuration Management

NASA Astrophysics Data System (ADS)

Wang, Wei; Feng, Weijia; Zhang, Wei; Li, Yuan

2018-01-01

At present, many equipment development companies have been aware of the great significance of reliability of the equipment development. But, due to the lack of effective management evaluation method, it is very difficult for the equipment development company to manage its own reliability work. Evaluation method of equipment reliability configuration management is to determine the reliability management capabilities of equipment development company. Reliability is not only designed, but also managed to achieve. This paper evaluates the reliability management capabilities by reliability configuration capability maturity model(RCM-CMM) evaluation method.

76 FR 56125 - Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-12

... DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket No. EERE-2011-BT-STD-0047] RIN 1904-AC56 Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment: Energy Conservation Standards for Direct Heating Equipment AGENCY: Office of Energy Efficiency and Renewable Energy, Department...

75 FR 41102 - Energy Conservation Program: Re-Opening of the Public Comment Period for Commercial Refrigeration...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-15

... Conservation Program: Re-Opening of the Public Comment Period for Commercial Refrigeration Equipment AGENCY... document for commercial refrigeration equipment and provide notice of a public meeting. The NOPM provided... the framework document for commercial refrigeration equipment is to be re-opened from July 15, 2010 to...

77 FR 76972 - Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-31

... Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment: Proposed... the criteria for covered equipment under Part A-1 of Title III of the Energy Policy and Conservation... the Energy Policy and Conservation Act V. Procedural Issues and Regulatory Review A. Review Under...

78 FR 11996 - Energy Efficiency Program for Commercial and Industrial Equipment: Commercial and Industrial Pumps

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-21

.... EERE-2011-BT-STD-0031] RIN 1904-AC54 Energy Efficiency Program for Commercial and Industrial Equipment... meeting and availability of the Framework Document pertaining to the development of energy conservation... to and the issues presented by these equipment types, and in consideration of the travel schedules of...

77 FR 29001 - Medicare and Medicaid Program; Regulatory Provisions to Promote Program Efficiency, Transparency...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-16

... constructed after January 1, 2008. Ambulatory Surgical Centers (ASC) Emergency Equipment: We have removed the detailed list of emergency equipment that must be available in an ASC's operating room. The current list includes outdated terminology as well as equipment that are not suitable for ASCs that furnish minor...

[Cost and effectiveness of exercise therapy for patients with essential hypertension].

PubMed

Harada, A; Kawakubo, K; Lee, J S; Fukuda, T; Kobayashi, Y

2001-09-01

While exercise therapy is established as an appropriate treatment for essential hypertension, its economic profile has not been fully evaluated. The purpose of this study is to evaluate cost and effectiveness in comparison with drug therapy. The study subjects were hypertensive patients under treatment at an outpatient clinic. Fifty-seven were selected on a non-randomized manner for exercise therapy and the same number of patients was chosen for drug therapy after matching age, sex, medication and complications. The following data were collected during three months of intervention. 1) Effectiveness: Change of systolic blood pressure before and after the intervention. 2) Cost: equipment, personnel expenses for exercise therapy and fees for health check-ups (exercise therapy); fees for consultation, laboratory examination and medications (drug therapy), 3) Cost-effectiveness: cost per 1 mmHg systolic blood pressure reduction. We evaluated the variance of cost-effectiveness by controlling the number of program participants, personnel expenses, and equipment expenses of exercise therapy. We also simulated how the cost-effectiveness of exercise therapy would improve by modifying the number of exercise participants, personnel and equipment expenses. The cost-effectiveness per 1 mmHg systolic blood pressure reduction was yen 11,268 for exercise therapy and yen 2,441 for drug therapy. Extending program facilities and increasing the number of participants would improve the cost-effectiveness of exercise therapy, but there were limitations to how far this could be achieved in the hospital setting. Differences in cost-effectiveness between exercise and drug therapies are attributed to differences in personnel expenses. Although they could be reduced by managerial effort of the hospital to some extent, outsourcing of exercise therapy to community-based facilities should be considered.

The effects of physical training without equipment on pain perception and balance in the elderly: A randomized controlled trial

PubMed Central

Patti, Antonino; Bianco, Antonino; Karsten, Bettina; Montalto, Maria Alessandra; Battaglia, Giuseppe; Bellafiore, Marianna; Cassata, Daniela; Scoppa, Fabio; Paoli, Antonio; Iovane, Angelo; Messina, Giuseppe; Palma, Antonio

2017-01-01

BACKGROUND: Research supports a link between exercise and falls prevention in the older population. OBJECTIVES: Our aims were to evaluate pain perception and balance skills in a group of elderly subjects and to examine the consequences of a standardized equipment-free exercise program intervention on these variables. The study utilized a randomized controlled trial method. METHODS: 92 subjects were recruited from a rural Sicilian village (Resuttano, Sicily, Italy). Subjects were randomly split into two groups, an experimental group (EG; n = 49) and a control group (CG; n = 43). Qualified fitness instructors delivered the standardized physical exercise program for the EG whilst the CG did not receive this exercise intervention. The Berg Balance Scale and the Oswestry Disability Index were administered in both groups before (T0) and after the intervention (T1). RESULTS: At T1, the EG group significantly improvement in balance (p < 0.0001) and pain perception (p < 0.0001). No significant differences were found within the CG both in BBS and ODI, respectively. CONCLUSIONS: Our findings suggest that a 13-weeks standardized exercise equipment-free program is effective in improving balance and perception of pain in the elderly. This type of intervention can consequently provide a low cost strategy to counteract the rate of disability in elderly. PMID:28506013

41 CFR 109-50.203 - Eligible equipment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 50-SPECIAL DOE DISPOSAL AUTHORITIES 50.2-Math and Science Equipment Gift Program § 109-50.203... and Laboratory Equipment. 67Photographic Equipment. 70General Purpose Automatic Data Processing...

41 CFR 109-50.203 - Eligible equipment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 50-SPECIAL DOE DISPOSAL AUTHORITIES 50.2-Math and Science Equipment Gift Program § 109-50.203... and Laboratory Equipment. 67Photographic Equipment. 70General Purpose Automatic Data Processing...

41 CFR 109-50.203 - Eligible equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 50-SPECIAL DOE DISPOSAL AUTHORITIES 50.2-Math and Science Equipment Gift Program § 109-50.203... and Laboratory Equipment. 67Photographic Equipment. 70General Purpose Automatic Data Processing...

41 CFR 109-50.203 - Eligible equipment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 50-SPECIAL DOE DISPOSAL AUTHORITIES 50.2-Math and Science Equipment Gift Program § 109-50.203... and Laboratory Equipment. 67Photographic Equipment. 70General Purpose Automatic Data Processing...

40 CFR 82.160 - Approved equipment testing organizations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.160 Approved.... The application shall be mailed to: Section 608 Recycling Program Manager; Global Programs Division... verifying the performance of certified recycling and recovery equipment manufactured over the long term...

40 CFR 82.160 - Approved equipment testing organizations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.160 Approved.... The application shall be mailed to: Section 608 Recycling Program Manager; Global Programs Division... verifying the performance of certified recycling and recovery equipment manufactured over the long term...

40 CFR 82.160 - Approved equipment testing organizations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.160 Approved.... The application shall be mailed to: Section 608 Recycling Program Manager; Global Programs Division... verifying the performance of certified recycling and recovery equipment manufactured over the long term...

40 CFR 82.160 - Approved equipment testing organizations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.160 Approved.... The application shall be mailed to: Section 608 Recycling Program Manager; Global Programs Division... verifying the performance of certified recycling and recovery equipment manufactured over the long term...

40 CFR 82.160 - Approved equipment testing organizations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.160 Approved.... The application shall be mailed to: Section 608 Recycling Program Manager; Global Programs Division... verifying the performance of certified recycling and recovery equipment manufactured over the long term...

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

This report is concerned with the nature and scope of the technical services to be rendered and the general plan proposed for operation of Building 3525, High Radiation Level Examination Laboratory (HRLEL). The role of postirradiation examination in implementing the over- all task of irradiation testing for various programs under way at the Oak Ridge National Laboratory (ORNL) and the importance of this effort to the United Stat es reactor development program are stressed . The shielded-cell complex with provisions for remote decontamination, hot-equipment storage, and maintenance is described, as well as other supporting activities which are incorporated into themore » facility. The proposed technical functions include general observation, mensuration, nondestructive testing, burnup and induced-activity measurements, fission-gas sampling and analysis, corrosion evaluation and related measurements, disassembly and cutup, metallographic examination, mechanical-property determinations , and x -ray diffraction analyses. Equipment design and operational features to improve detection and measurement of selected properties in radioactive material s are described, also. The current status on design, procurement, construction, and preoperational testing of in- cell equipment in the mockup is presented along with a forecast of future needs. The mode of operation, manpower requirements, and management of the facility are discussed.« less

Physical training programs for public safety personnel.

PubMed

Moulson-Litchfield, M; Freedson, P S

1986-07-01

The nature of public safety jobs often reflects sudden strenuous exertion at a moment's notice. In the 1970s, police and fire departments became acutely aware of high numbers of on-the-job injuries and illnesses related to coronary heart disease. Disability payments for premature cardiovascular problems were being linked to cardiovascular risk factors accrued while on the job. This prompted public safety departments to initiate fitness programs for their employees. The fitness level of public safety personnel is not high. Job-related benefits have been linked to consistent physical training; high aerobic capacity, high muscular strength and endurance, above-average lean body weight, and minimal body fat are necessary for efficient job performance. In light of the physical benefits gained through regular exercise, pioneer departments began exercise programs for their personnel. These included the fire departments in Lawrence, Kansas, Alexandria, Virginia and Los Angeles, and the Dallas police department. Mealey documents psychologic improvements with exercise. Pioneer fitness programs such as that of the Los Angeles fire department have noted evidence of risk-factor reduction following institution of a mandatory program. The Alexandria department has instituted mandatory entrance requirements for their recruits, such as a no-smoking policy while on the job and mandatory exercise participation. Many community departments are not able to justify the institution of fitness programs. They may cite cost, lack of space, or lack of administrative support for the inability to initiate these programs. Legal and union ramifications may also deter the effort of program implementation. Considerations when implementing programs should involve cost of equipment, space, employee input, and determination of mandatory versus voluntary status. Preliminary medical screening and fitness evaluations should reliably evaluate an employee's physical ability to perform job-related tasks. The tests should be performed on a regular basis during employment. It is important, therefore, to convey the benefits of exercise to administrators. Frequent exercise testing should record progress of participants during exercise training and goals should be constantly updated. Pioneer programs should be used as models to follow when implementing a public safety physical training program. However, individual departments should evaluate the needs of their own personnel with respect to equipment, exercise schedule and type, and place of training.(ABSTRACT TRUNCATED AT 400 WORDS)

Exploration of government policy structure which support and block energy transition process in indonesia using system dynamics model

NASA Astrophysics Data System (ADS)

Destyanto, A. R.; Silalahi, T. D.; Hidayatno, A.

2017-11-01

System dynamic modeling is widely used to predict and simulate the energy system in several countries. One of the applications of system dynamics is to evaluate national energy policy alternatives, and energy efficiency analysis. Using system dynamic modeling, this research aims to evaluate the energy transition policy that has been implemented in Indonesia on the past conversion program of kerosene to LPG for household cook fuel consumption, which considered as successful energy transition program implemented since 2007. This research is important since Indonesia considered not yet succeeded to execute another energy transition program on conversion program of oil fuel to gas fuel for transportation that has started since 1989. The aim of this research is to explore which policy intervention that has significant contribution to support or even block the conversion program. Findings in this simulation show that policy intervention to withdraw the kerosene supply and government push to increase production capacity of the support equipment industries (gas stove, regulator, and LPG Cylinder) is the main influence on the success of the program conversion program.

Developing a Successful High School Science Research Program via Teacher Training, Student Internships, and Community Support

NASA Astrophysics Data System (ADS)

Danch, J. M.; Darytichen, F.

2004-12-01

The purpose of the Science Research Program is to allow students to perform authentic scientific research in disciplines of their choosing over a period of 3 years. The success of the program has allowed for expansion including community involvement, student mentorship, and a series of professional development programs. Through state and national competition and community symposia, student research is evaluated, showcased, and subsequently supported both idealistically and financially by local government and industrial partnerships. Student internships and university/industrial mentorship programs allow students to pursue research topics and utilize equipment exceeding the scope of the secondary science classroom. Involved teachers have developed and delivered professional development workshops to foster the successful implementation of scientific research programs at additional high schools throughout the state.

Energy Efficiency and Renewable Energy Program. Bibliography, 1993 edition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaughan, K.H.

1993-06-01

The Bibliography contains listings of publicly available reports, journal articles, and published conference papers sponsored by the DOE Office of Energy Efficiency and Renewable Energy and published between 1987 and mid-1993. The topics of Bibliography include: analysis and evaluation; building equipment research; building thermal envelope systems and materials; district heating; residential and commercial conservation program; weatherization assistance program; existing buildings research program; ceramic technology project; alternative fuels and propulsion technology; microemulsion fuels; industrial chemical heat pumps; materials for advanced industrial heat exchangers; advanced industrial materials; tribology; energy-related inventions program; electric energy systems; superconducting technology program for electric energy systems; thermalmore » energy storage; biofuels feedstock development; biotechnology; continuous chromatography in multicomponent separations; sensors for electrolytic cells; hydropower environmental mitigation; environmental control technology; continuous fiber ceramic composite technology.« less

THE ETV P2 INNOVATIVE COATINGS AND COATING EQUIPMENT PROGRAM--AN UPDATE

EPA Science Inventory

The paper focuses on the Pollution Prevention (P2), Recycling, and Waste Treatment Systems Center of the EPA's Environmental Technology Verification (ETV) Program and, specifically, the P2 Innovating Coatings and Coating Equipment Program (CCEP) housed within the Center. The focu...

45 CFR 95.701 - Purpose and scope of subpart.

Code of Federal Regulations, 2010 CFR

2010-10-01

... requirements for the management and disposition of equipment whose costs are claimed for Federal financial... ADMINISTRATION-GRANT PROGRAMS (PUBLIC ASSISTANCE, MEDICAL ASSISTANCE AND STATE CHILDREN'S HEALTH INSURANCE PROGRAMS) Equipment Acquired Under Public Assistance Programs § 95.701 Purpose and scope of subpart. (a...

45 CFR 95.701 - Purpose and scope of subpart.

Code of Federal Regulations, 2011 CFR

2011-10-01

... requirements for the management and disposition of equipment whose costs are claimed for Federal financial... ADMINISTRATION-GRANT PROGRAMS (PUBLIC ASSISTANCE, MEDICAL ASSISTANCE AND STATE CHILDREN'S HEALTH INSURANCE PROGRAMS) Equipment Acquired Under Public Assistance Programs § 95.701 Purpose and scope of subpart. (a...

Outdoor Power Equipment Technician Program. Apprenticeship Training.

ERIC Educational Resources Information Center

Alberta Learning, Edmonton. Apprenticeship and Industry Training.

This document presents information about the apprenticeship training program of Alberta, Canada, in general and the outdoor power equipment technician program in particular. The first part of the document discusses the following items: Alberta's apprenticeship and industry training system; the apprenticeship and industry training committee…

40 CFR 160.61 - Equipment design.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS GOOD LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation...

Evaluation of artillery equipment maintenance support capability based on grey clustering

NASA Astrophysics Data System (ADS)

Zhai, Mei-jie; Gao, Peng

2017-12-01

This paper, the theory and method of evaluating the capability of equipment maintenance support in China and abroad are studied, from the point of view of the combat task of artillery troops and the strategic attachment in the future military struggle. This paper establishes the framework of the evaluation Index system of the equipment maintenance support capability of the artillery units, and applies the grey clustering method to the evaluation of the equipment maintenance support capability of the artillery units, and finally evaluates the equipment maintenance and support capability of the artillery brigade as an example, and analyzes the evaluation results. This paper finds out the outstanding problems existing in the maintenance and support of military equipment, and puts forward some constructive suggestions, in order to improve the status of military equipment maintenance and support and improve the level of future equipment maintenance.

18 CFR 367.9080 - Account 908, Customer assistance expenses.

Code of Federal Regulations, 2013 CFR

2013-04-01

... electric equipment. (4) Demonstrations, exhibits, lectures, and other programs designed to instruct..., lectures, and other programs. (2) Loss in value on equipment and appliances used for customer assistance...

18 CFR 367.9080 - Account 908, Customer assistance expenses.

Code of Federal Regulations, 2014 CFR

2014-04-01

... electric equipment. (4) Demonstrations, exhibits, lectures, and other programs designed to instruct..., lectures, and other programs. (2) Loss in value on equipment and appliances used for customer assistance...

18 CFR 367.9080 - Account 908, Customer assistance expenses.

Code of Federal Regulations, 2011 CFR

2011-04-01

... electric equipment. (4) Demonstrations, exhibits, lectures, and other programs designed to instruct..., lectures, and other programs. (2) Loss in value on equipment and appliances used for customer assistance...

18 CFR 367.9080 - Account 908, Customer assistance expenses.

Code of Federal Regulations, 2012 CFR

2012-04-01

... electric equipment. (4) Demonstrations, exhibits, lectures, and other programs designed to instruct..., lectures, and other programs. (2) Loss in value on equipment and appliances used for customer assistance...

78 FR 79649 - Energy Conservation Program: Proposed Determination of Set-Top Boxes and Network Equipment as a...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-31

... Conservation Program: Proposed Determination of Set-Top Boxes and Network Equipment as a Covered Consumer... published June 15, 2011 that set-top boxes (STBs) and network equipment qualify as a covered product under... action in light of a consensus agreement entered by a broadly representative group that DOE believes has...

Identification of the actual state and entity availability forecasting in power engineering using neural-network technologies

NASA Astrophysics Data System (ADS)

Protalinsky, O. M.; Shcherbatov, I. A.; Stepanov, P. V.

2017-11-01

A growing number of severe accidents in RF call for the need to develop a system that could prevent emergency situations. In a number of cases accident rate is stipulated by careless inspections and neglects in developing repair programs. Across the country rates of accidents are growing because of a so-called “human factor”. In this regard, there has become urgent the problem of identification of the actual state of technological facilities in power engineering using data on engineering processes running and applying artificial intelligence methods. The present work comprises four model states of manufacturing equipment of engineering companies: defect, failure, preliminary situation, accident. Defect evaluation is carried out using both data from SCADA and ASEPCR and qualitative information (verbal assessments of experts in subject matter, photo- and video materials of surveys processed using pattern recognition methods in order to satisfy the requirements). Early identification of defects makes possible to predict the failure of manufacturing equipment using mathematical techniques of artificial neural network. In its turn, this helps to calculate predicted characteristics of reliability of engineering facilities using methods of reliability theory. Calculation of the given parameters provides the real-time estimation of remaining service life of manufacturing equipment for the whole operation period. The neural networks model allows evaluating possibility of failure of a piece of equipment consistent with types of actual defects and their previous reasons. The article presents the grounds for a choice of training and testing samples for the developed neural network, evaluates the adequacy of the neural networks model, and shows how the model can be used to forecast equipment failure. There have been carried out simulating experiments using a computer and retrospective samples of actual values for power engineering companies. The efficiency of the developed model for different types of manufacturing equipment has been proved. There have been offered other research areas in terms of the presented subject matter.

Exploring the Perceived Benefits and Limitations of a School-Based Social-Emotional Learning Program: A Concept Map Evaluation

ERIC Educational Resources Information Center

Haymovitz, Ethan; Houseal-Allport, Pia; Lee, R. Scott; Svistova, Juliana

2018-01-01

Schools today are faced with the challenge of equipping students with the skills they need to succeed in life outside the classroom while also teaching the academic material required. More often, teachers are called on to establish environments in which students learn social and emotional skills alongside academics. With increased recognition that…

P.L. 89-313. Supplementary Services for Previously Nonpublic School Institutionalized Students, 1983-84. O.E.E. Evaluation Report.

ERIC Educational Resources Information Center

Tobias, Robert; And Others

During 1983-84, the Public Law 89-313 program served 2,053 students who were formerly educated in State-operated or State-supported schools through the following components and subcomponents: the Regional Services Instructional Support Unit; Citywide Services, consisting of Instructional Supplies and Equipment and Hearing Education Services; and…

Equipment Level Fallout Radiation Effects Approach

DTIC Science & Technology

1989-02-10

Electromagnetic Pulse (EMP) mitigation Program to evaluate and, where possible, mitigate the effects of the nuclear attack. Fallout radiation has been identified as an environment which may effect the performance of the regional and national telecommunication system. This report presents the investigations in the network level fallout radiation methodology used to determine the effects of this environment. Alternative techniques are presented to improve the

The Role of Obstetric Knowledge in Utilization of Delivery Service in Nepal

ERIC Educational Resources Information Center

Karkee, Rajendra; Baral, Om Bahadur; Khanal, Vishnu; Lee, Andy H.

2014-01-01

Birth Preparedness and Complication Readiness (BP/CR) program has been promoted in Nepal to equip pregnant women with obstetric knowledge so as to motivate them to seek professional care. Using a prospective design of 701 pregnant women of more than 5 months gestation in a central hills district of Nepal, we evaluated if having obstetric knowledge…

FIELD COLLECTION METHODS USED IN THE EPA NATIONAL EXPOSURE RESEARCH LABORATORY HUMAN EXPOSURE MEASUREMENT PROGRAM TO EVALUATE CHILDREN'S AGGREGATE EXPOSURE TO PESTICIDES: A TUTORIAL

EPA Science Inventory

A tutorial on the field sampling equipment used to collect multimedia samples.

We conduct observational human exposure measurement studies in order to understand what chemicals people come into contact with, at what levels, what the sources of those chemicals are, and wher...

1-to-1 Computing: A Measure of Success

ERIC Educational Resources Information Center

O'Hanlon, Charlene

2007-01-01

When Texas' Technology Immersion Project began in the spring of 2004, a grant from the US Department of Education allowed a parallel project to launch--eTxTIP--to evaluate and measure the success of the program, which equips middle school students in high-risk, high-need areas with laptops. Data is beginning to come in on several of the first…

Flammability, Odor, Offgassing, and Compatibility Requirements and Test Procedures for Materials in Environments that Support Combustion

NASA Technical Reports Server (NTRS)

1998-01-01

This handbook establishes NASA program requirements for evaluation, testing, and selection of materials to preclude unsafe conditions related to flammability, odor, offgassing, and fluid compatibility. Materials intended for use in space vehicles, specified test facilities, and specified ground support equipment (GSE) must meet the requirements of this document. Additional materials performance requirements may be specified in other program or NASA center specific documentation. Responsible NASA centers materials organizations must include applicable requirements of this document in their materials control programs. Materials used in habitable areas of spacecraft, including the materials of the spacecraft, stowed equipment, and experiments, must be evaluated for flammability, odor, and offgassing characteristics. All materials used in other areas must be evaluated for flammability characteristics. In addition, materials that are exposed to liquid oxygen (LOX), gaseous oxygen (GOX), and other reactive fluids' must be evaluated for compatibility with the fluid in their use application. Materials exposed to pressurized breathing gases also must be evaluated for odor and offgassing characteristics. The worst-case anticipated use environment (most hazardous pressure, temperature, material thickness, and fluid exposure conditions) must be used in the evaluation process. Materials that have been shown to meet the criteria of the required tests are acceptable for further consideration in design. Whenever possible, materials should be selected that have already been shown to meet the test criteria in the use environment. Existing test data are compiled in the NASA Marshall Space Flight Center (MSFC) Materials and Processes Technical Information System (MAPTIS) and published periodically as the latest revision of a joint document with Johnson Space Center (JSC), MSFC-HDBK-527/JSC 09604. MAPTIS can be accessed by computer datalink. Systems containing materials that have not been tested or do not meet the criteria of the required tests must be verified to be acceptable in the use configuration by analysis or testing. This verification rationale must be documented and submitted to the responsible NASA center materials organization for approval.

Airport Lighting Equipment Certification Program

DOT National Transportation Integrated Search

1995-05-15

This advisory circular (AC) describes the Airport Lighting Equipment : Certification Program (ALECP). It provides information on how an organization : can get Federal Aviation Administration (FAA) acceptance as a third party : certification body and ...

78 FR 36478 - Accessibility of User Interfaces, and Video Programming Guides and Menus

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-18

... equipment: ``digital apparatus'' and ``navigation devices.'' Specifically, section 204 applies to ``digital... apparatus, including equipment purchased at retail by a consumer to access video programming, would be..., and video programming guides, and menus provided by digital apparatus and navigation devices are...

Cocurrent scrubber evaluation: TVA's Colbert lime-limestone wet-scrubbing pilot plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hollinden, G.A.; Robards, R.F.; Moore, N.D.

1979-01-01

The Tennessee Valley Authority (TVA) is actively engaged in a pilot plant program to develop and/or evaluate wet-scrubbing processes for removing sulfur dioxide (SO/sub 2/) from boiler flue gas. The physical size and general arrangement of flue gas scrubbing systems have a major impact on capital investment and operating cost, as do potential operating and maintenance advantages inherent to some systems. The equipment configuration for a cocurrent scrubber reflects some of these advantages. EPRI funded TVA to perform preliminary screening tests at TVA's 1 MW pilot plant (Colbert Steam Plant) to develop operating data on the cocurrent design for usemore » in designing and operating a 10 MW prototype cocurrent scrubber at TVA's Shawnee Scrubber Test Facility. Results of Colbert tests showed excellent sulfur dioxide removal efficiencies, generally greater than 85%, low pressure drop, and high particulate removal efficiencies. This report covers these screening tests. The results indicate that commercial application of the cocurrent scrubber concept may save substantial capital investment by reducing the number of scrubber modules and auxiliary equipment. These evaluation tests provided the basis for the design and construction of the 10 MW cocurrent scrubber at the Shawnee Facility. Operation of this scrubber began in August 1978 to develop the scale-up similarities and differences between the Colbert test program (1 MW) and the Shawnee test program (10 MW). It also demonstrated the practicality and reliability of the 10 MW prototype. Detailed results of the prototype test series will be available in late 1979.« less

76 FR 40285 - Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

..., data, and information regarding the proposed determination for set-top boxes and network equipment... encryption. Postal Mail: Ms. Brenda Edwards, U.S. Department of Energy, Building Technologies Program... Energy, Building Technologies Program, 950 L'Enfant Plaza, SW., 6th Floor, Washington, DC 20024. Please...

Lighting Equipment (Update to Listing)

DOT National Transportation Integrated Search

1996-05-06

This listing contains equipment and manufacturers certified or deleted since publication of advisory circular 150/5345-53A, Airport lighting equipment certification program, on 5-15-95. The equipment and manufacturers will be added to or deleted from...

Issues related to line-oriented flight training

NASA Technical Reports Server (NTRS)

Lauber, J. K.

1981-01-01

The use of a training simulator along with carefully structured, detailed, line trip scenarios was envisioned by NASA as a means of providing a controllable, repeatable way to observe line crews in a highly realistic simulation of their working environment and obtain better understanding operationally significant human factors problems and issues. Relevant research done by the agency and the results of full-mission simulation scenarios revealed potential implications for flight training. Aspects to be considered in creating training programs closely related to the actual line environment with a total crew application in real world incident experiences include: (1) operational, environmental, equipment, and crew problems in scenario design; (2) real time line oriented flight training operation; (3) performance assessment and debriefing; (4) instructor qualification and training; and (5) other issues such as ub un initial, transition, and upgrade training; procedures developent and evaluation, and equipment evaluation.

Shouldering the load: A review of Joan Stevenson's work on occupational lifting and design evaluation of load carriage equipment.

PubMed

Costigan, Patrick A; Morin, Evelyn L; Reid, Susan A

2014-01-01

In this paper, Dr. Joan Stevenson's work on assessment of the effects of lifting, supporting and transporting loads is reviewed. A defining attribute of this work is the use of objective, biomechanical measures as the basis from which a fuller understanding of all factors affecting worker performance can be obtained, and how such performance should be measured and evaluated. The central objectives and conclusions of Dr. Stevenson's research programs spanning the years from 1985 through 2012 are summarized and discussed in terms of an overall research trajectory. The guiding principle of Dr. Stevenson's work is to reduce the potential harm to which workers are exposed through the development of bona fide occupational standards, a better understanding of risk factors leading to low back pain, and the establishment of an enhanced objective design process for functional load-bearing clothing and equipment.

Analysis of Refrigeration Equipment in School Nutrition Programs in the USDA/FNS Southwest Region

ERIC Educational Resources Information Center

Webb, Virginia Susan

2012-01-01

Equipment to store foods at proper temperatures is critical to serving safe and nutritious meals in schools yet little is known about the amount or the adequacy of refrigerated storage in school nutrition programs. The purposes of this study were to identify the types and capacity of refrigeration equipment used in schools, determine the perceived…

Industrial Technology Modernization Program. Project 32. Factory Vision. Phase 2

DTIC Science & Technology

1988-04-01

instructions for the PWA’s, generating the numerical control (NC) program instructions for factory assembly equipment, controlling the process... generating the numerical control (NC) program instructions for factory assembly equipment, controlling the production process instructions and NC... Assembly Operations the "Create Production Process Program" will automatically generate a sequence of graphics pages (in paper mode), or graphics screens

Research on the use of data fusion technology to evaluate the state of electromechanical equipment

NASA Astrophysics Data System (ADS)

Lin, Lin

2018-04-01

Aiming at the problems of different testing information modes and the coexistence of quantitative and qualitative information in the state evaluation of electromechanical equipment, the paper proposes the use of data fusion technology to evaluate the state of electromechanical equipment. This paper introduces the state evaluation process of mechanical and electrical equipment in detail, uses the D-S evidence theory to fuse the decision-making layers of mechanical and electrical equipment state evaluation and carries out simulation tests. The simulation results show that it is feasible and effective to apply the data fusion technology to the state evaluation of the mechatronic equipment. After the multiple decision-making information provided by different evaluation methods are fused repeatedly and the useful information is extracted repeatedly, the fuzziness of judgment can be reduced and the state evaluation Credibility.

Comparative evaluation of ERTS-A imagery for resource inventory in land-use planning

NASA Technical Reports Server (NTRS)

Simonson, G. H. (Principal Investigator)

1972-01-01

There are no author-identified significant results in this report. The overall objectives of this program are: (1) use of multidiscipline team approach to determine features that can be successfully monitored by ERTS-1 imagery for resource inventory, planning, land use zoning, and resource development; and (2) using carefully selected sample areas, develop a comprehensive resource inventory mapping system for use in planning, zoning, and resource development. Progress has included compilation and organization of ground truth data and observations in the primary study area of Crook County; resource inventory legend development; assembly and testing of color enhancement equipment; development and adaption of programs for digital data processing; and quick-look evaluations of initial ERTS-1 imagery for Oregon.

A Module Experimental Process System Development Unit (MEPSDU)

NASA Technical Reports Server (NTRS)

1981-01-01

The purpose of this program is to demonstrate the technical readiness of a cost effective process sequence that has the potential for the production of flat plate photovoltaic modules which met the price goal in 1986 of $.70 or less per watt peak. Program efforts included: preliminary design review, preliminary cell fabrication using the proposed process sequence, verification of sandblasting back cleanup, study of resist parameters, evaluation of pull strength of the proposed metallization, measurement of contact resistance of Electroless Ni contacts, optimization of process parameter, design of the MEPSDU module, identification and testing of insulator tapes, development of a lamination process sequence, identification, discussions, demonstrations and visits with candidate equipment vendors, evaluation of proposals for tabbing and stringing machine.

Shuttle spacelab simulation using a Lear jet aircraft: Mission no. 3 (ASSESS program)

NASA Technical Reports Server (NTRS)

Reller, J. O., Jr.; Neel, C. B.; Mason, R. H.

1974-01-01

The third ASSESS mission using a Lear Jet aircraft conducted to continue the study of scientific experiment operations in a simulated Spacelab environment. Prior to the mission, research planning and equipment preparation were observed and documented. A flight readiness review for the experiment was conducted. Nine of the ten scheduled flights were completed during simulation mission and all major science objectives were accomplished. The equipment was well qualified for flight and gave little trouble; telescope malfunctions occurred early in the mission and were corrected. Both real-time and post-observation data evaluation were used to assess research progress and to plan subsequent flight observations for maximum effectiveness.

77 FR 72763 - Energy Conservation Program: Certification of Commercial and Industrial HVAC, Refrigeration and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-06

... Commercial and Industrial HVAC, Refrigeration and Water Heating Equipment AGENCY: Office of Energy Efficiency... extension to the compliance date for the certification provisions of commercial refrigeration equipment... refrigeration equipment; commercial HVAC equipment; commercial WH equipment; and walk-in coolers and freezers...

External quality-assurance programs managed by the U.S. Geological Survey in support of the National Atmospheric Deposition Program/National Trends Network

USGS Publications Warehouse

Latysh, Natalie E.; Wetherbee, Gregory A.

2005-01-01

The U.S. Geological Survey, Branch of Quality Systems, operates the external quality-assurance programs for the National Atmospheric Deposition Program/National Trends Network (NADP/NTN). Beginning in 1978, six different programs have been implemented?the intersite-comparison program, the blind-audit program, the sample-handling evaluation program, the field-audit program, the interlaboratory-comparison program, and the collocated-sampler program. Each program was designed to measure error contributed by specific components in the data-collection process. The intersite-comparison program, which was discontinued in 2004, was designed to assess the accuracy and reliability of field pH and specific-conductance measurements made by site operators. The blind-audit and sample-handling evaluation programs, which also were discontinued in 2002 and 2004, respectively, assessed contamination that may result from sampling equipment and routine handling and processing of the wet-deposition samples. The field-audit program assesses the effects of sample handling, processing, and field exposure. The interlaboratory-comparison program evaluates bias and precision of analytical results produced by the contract laboratory for NADP, the Illinois State Water Survey, Central Analytical Laboratory, and compares its performance with the performance of international laboratories. The collocated-sampler program assesses the overall precision of wet-deposition data collected by NADP/NTN. This report documents historical operations and the operating procedures for each of these external quality-assurance programs. USGS quality-assurance information allows NADP/NTN data users to discern between actual environmental trends and inherent measurement variability.

Implementing the EQUiPPED Medication Management Program at 5 VA Emergency Departments.

PubMed

Vandenberg, Ann E; Stevens, Melissa; Echt, Katharina V; Hastings, S Nicole; Powers, James; Markland, Alayne; Hwang, Ula; Hung, William; Belbis, Stephanie; Vaughan, Camille P

2016-04-01

The Enhancing Quality of Prescribing Practices for Older Veterans Discharged From the Emergency Department (EQUiPPED) program aimed to reduce potentially inappropriate medication prescribing to older adults at 5 VAMCs.

Your Guide to Living Well with Heart Disease

MedlinePlus

... effective for you. Some programs make use of equipment such as a treadmill for walking, stationary bikes, ... you’ll be shown how to use this equipment to get the most benefit. Other programs offer ...

Does your equipment maintenance management program measure up?

PubMed

Deinstadt, Deborah C

2003-01-01

Identifying a clear maintenance philosophy is the first step toward choosing the right program for your healthcare organization. The second step is gaining a clear understanding of how proposed savings and improvements will be delivered. The third and last step is requiring that the proposed company or manager have specific tools in place for measuring and analyzing program performance. There are three primary philosophies underlying current equipment management options. These include risk-transfer philosophy (e.g., maintenance insurance, service contracts, multi-vendor and outsource programs), asset management philosophy (e.g., programs delivering a management system based on managed time-and-materials), and internal management (in-house managed programs). The last step in selecting the right program is insisting that proper performance measurements be built into the proposed management program. A well-managed program provides results in three general areas: financial outcomes, operational improvements and process improvements. Financial outcomes are the easiest to measure. Operational and process improvements are more challenging to assess but equally important to the program's overall success. To accurately identify results in these three areas, the overall management program should measure the following eight separate components: procedures and support for department staff; equipment inventory, benchmark costs, and budget guidelines; experienced equipment support team; objective, independent analysis of maintenance events; repair documentation and reporting; vendor relations; equipment acquisition analysis; and recommendations for improvement. Do everything you reasonably can to assure that the selected company can work side-by-side with you, providing objective, measurable advice that is ultimately in your best interest. You will then know that you have been thorough in your marketplace selection and can confidently move into implementation, expecting tangible and successful results.

Bidirectional power converter control electronics

NASA Technical Reports Server (NTRS)

Mildice, J. W.

1987-01-01

The object of this program was to design, build, test, and deliver a set of control electronics suitable for control of bidirectional resonant power processing equipment of the direct output type. The program is described, including the technical background, and results discussed. Even though the initial program tested only the logic outputs, the hardware was subsequently tested with high-power breadboard equipment, and in the testbed of NASA contract NAS3-24399. The completed equipment is now operating as part of the Space Station Power System Test Facility at NASA Lewis Research Center.

Growing Prospects in Manitoba: Drug Equipment Spices Up Youth Job Training Program.

ERIC Educational Resources Information Center

Montague, Arthur

2002-01-01

A Winnipeg (Manitoba) school teacher started a nonprofit job skills training program for at-risk youth. Police donated equipment confiscated from marijuana cultivators to the program, which trains youth aged 15-29 in hydroponics, horticulture, and greenhouse operations. More than 75 percent of its graduates are employed in greenhouse or related…

Mobile Training Laboratories, Mobile Equipment and Programs Offered in Business or Industry. Status Report.

ERIC Educational Resources Information Center

Harry, Raymond L.

A literature review and telephone survey examined the following alternate methods for delivering vocational education services: mobile training laboratories, mobile training programs, training programs offered by educational institutions in business and industry facilities, and equipment loaned or supplied as a gift by business and industry for…

40 CFR 1039.625 - What requirements apply under the program for equipment-manufacturer flexibility?

Code of Federal Regulations, 2010 CFR

2010-07-01

... in this section only if you have primary responsibility for designing and manufacturing equipment and... specifically to companies that manufacture equipment outside the United States and to companies that import such equipment without manufacturing it. Engines and equipment you produce under this section are...

40 CFR 1054.625 - What requirements apply under the Transition Program for Equipment Manufacturers?

Code of Federal Regulations, 2010 CFR

2010-07-01

... if you have primary responsibility for designing and manufacturing equipment and your manufacturing... specifically to companies that manufacture equipment outside the United States and to companies that import such equipment without manufacturing it. Engines and equipment you produce under this section are...

PR^2EPS: Preparation, Recruitment, Retention and Excellence in the Physical Sciences.

NASA Astrophysics Data System (ADS)

Labroo, Sunil; Schaumloffel, John; Gallagher, Hugh; Bischoff, Paul; Bachman, Nancy

2007-03-01

The PR^2EPS program is a multidisciplinary effort to increase the number of majors attending (and graduating) from SUNY Oneonta with degrees in chemistry, physics, biochemistry, astronomy, secondary chemistry or physics education and related areas. Components of the program include a walk-in tutoring center, a free, weeklong summer science camp, scholarship opportunities and an equipment loan program for regional secondary science teachers. 2006 was the third year of this NSF-DUE funded program. Evaluation of our progress to date shows that the program is effective at steering students (or at least reinforcing their desire) to studying the sciences in college. A summary of our goals, challenges and accomplishments, including tutoring center operation and efficacy, activities and operational details for the summer camp and other facets of the program will be presented.

CG Vessel Traffic Service Program.

DTIC Science & Technology

1980-06-01

Corps of Engineers and the Maritime Administration have forecast that total commercial cargo transported through U.S. ports and waterways will increase... electronic navigation and surveillance equipment since the early 1960’s to evaluate various concepts by which vessel traffic safety could be enhanced...relatively complete data base on vessel traffic. On the other hand, the addition of radar and other electronic surveillance should: --Prevent vessel

An Analysis of Unplanned Requirements and Their Impact on the Naval Electronic Systems Command

DTIC Science & Technology

1976-06-01

Evaluation Repair Turnaround Time Ship Alteration Management Information System Shipbuilding and Conversion, Navy Standard Hardware Program Ships Parts...pending assigment of a NSN. Such equipments would have little opportunity to accumulate any demand history. Secondly, the relatively low percentage of...mentioned above. Unfortunately, sufficient historical information was not available to fully accomplish this goal. In the case of assets acquired from

Response to Intervention (RTI): A Mixed Methods Study Evaluating the Effects of Behavior Training Software on Behavior of In-School Suspension Students

ERIC Educational Resources Information Center

Cooper, Rosie Nicole

2014-01-01

Excessive classroom disruption is prevalent among today's public high schools and is a deterrent to the academic and social achievements of students. Using Response to Intervention (RtI) to equip in-school suspension (ISS) programs with a research-based behavioral curriculum is one possible solution to efficiently and cost-effectively remediating…

Defense AT&L. Volume 42, Number 3, May-June 2013

DTIC Science & Technology

2013-06-01

known program that demonstrated the government’s remarkable ability to streamline the process to develop , evaluate, and field within 2 years is the... abreast of research and development initiatives, confer- ences, and symposia. Collaboration across DoD increases our ability to identify challenges...stan and Iraq over the last 10 years has challenged materiel developers to keep pace in providing equipment, vehicles, surveillance, and weapons

Switching Patients to Home-Based Subcutaneous Immunoglobulin: an Economic Evaluation of an Interprofessional Drug Therapy Management Program.

PubMed

Perraudin, Clemence; Bourdin, Aline; Spertini, Francois; Berger, Jérôme; Bugnon, Olivier

2016-07-01

Home-based subcutaneous immunoglobulin (SCIg) therapy is an alternative to hospital-based intravenous infusions (IVIg). However, SCIg requires patient training and long-term support to ensure proper adherence, optimal efficacy and safety. We evaluated if switching patients to home-based SCIg including an interprofessional drug therapy management program (physician, community pharmacist and nurse) would be cost-effective within the Swiss healthcare system. A 3-year cost-minimization analysis was performed from a societal perspective comparing monthly IVIg in an outpatient clinic and home-based weekly SCIg including an interprofessional program. Healthcare costs (immunoglobulin, professional time, infusion pump and disposables) were derived from administrative data. Transportation and productivity loss were estimated by expert opinion. The results were expressed in Swiss francs (CHF) and converted to Euros and US dollars (1 CHF = 0.92€, 1 CHF = $1.02; www.xe.com , 12/14/2015). Under base case assumptions, SCIg was estimated to cost 35,862 CHF (33,134€; $36,595) per patient during the first year and 30,309 CHF (28,004€; $30,929) in subsequent years versus 35,370 CHF (32,679€; $36,095) per year for IVIg. The total savings from switching to SCIg with the interprofessional program were 9630 CHF (8897€; $9828) per patient over 3 years. The results were relatively sensitive to the cost per gram of IgG, the cost of equipment and the annual number of infusions. Home-based SCIg including an interprofessional therapy management program may be an efficient alternative for patients. The program provides long-term support from self-administration training to the responsible use of therapy (proper adherence, optimal efficacy and safety). Over the short term, additional costs from purchasing equipment and the drug therapy management program were offset by avoiding hospital costs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giovanni, D.V.; Carr, R.C.; Landham, E.C.

Two products of coal quality research at the Electric Power Research Institute TM (EPRI) are available for field evaluation: Coal Quality Impact Model (CQIM and Fireside Testing Guidelines (FIG). The CQIM is a computer program that may be tailored to simulate the performance characteristics of a coal-fired power plant. The FIG is a technical report that guides utilities in conducting field tests to gather performance data and quantify the technical and economic impacts of different coals. Moreover, the results from field tests may be utilized to validate and assess the applicability of the CQIM. Field tests were conducted at Mississippimore » Power Company`s Watson Unit 4 to evaluate the coal quality impacts of coal switching on boiler performance and emissions. Watson Unit 4 is a 255 MW (gross), opposed-wall, pulverized-coal-fired boiler manufactured by Riley Stoker Corporation and rated at 1,779,000 lb/hr steam flow at 1000{degrees}F superheat steam temperature and 2,500 psig. The unit is equipped with a cold-side electrostatic precipitator for particulate matter control. Comprehensive tests were conducted on all major equipment components, including the pulverizers, fans, combustion equipment, boiler heat transfer surfaces, air preheater, and electrostatic precipitator, for two coals. The CQIN4 was configured to predict the performance of the unit when burning each coal. The work was sponsored by EPRI, and Mississippi Power Company (MPC) was the host utility company. This report summarizes results from the field test program, including potential heat rate improvements that were identified, and the differences in unit operations and performance for the two coals. The results from the CQIM validation effort are also presented.« less

Implementing the EQUiPPED Medication Management Program at 5 VA Emergency Departments

PubMed Central

Vandenberg, Ann E.; Stevens, Melissa; Echt, Katharina V.; Hastings, S. Nicole; Powers, James; Markland, Alayne; Hwang, Ula; Hung, William; Belbis, Stephanie; Vaughan, Camille P.

2016-01-01

The Enhancing Quality of Prescribing Practices for Older Veterans Discharged From the Emergency Department (EQUiPPED) program aimed to reduce potentially inappropriate medication prescribing to older adults at 5 VAMCs. PMID:27773986

Long term pavement performance program protocol for calibrating traffic data collection equipment

DOT National Transportation Integrated Search

1998-05-10

This document describes the procedures that the Long Term Pavement Performance (LTPP) program recommends for ensuring that traffic data collection equipment used for LTPP traffic monitoring efforts operates correctly and collects valid data.

78 FR 41333 - Energy Efficiency Program for Commercial and Industrial Equipment: Public Meeting and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-10

.... EERE-2013-BT-STD-0022] RIN 1904-AD00 Energy Efficiency Program for Commercial and Industrial Equipment... the Framework Document pertaining to the development of energy conservation standards for refrigerated...

Education Model Program on Water-Energy Research: A New STEM Graduate Program from Development through Evaluation

NASA Astrophysics Data System (ADS)

McCay, D.; Fiorenza, P.; Lautz, L.

2017-12-01

More than half of Ph.D. scientists and engineers find employment in non-academic sectors. Recognizing the range of career options for graduate degree holders and the need to align graduate education with the expectations of prospective employers, the National Science Foundation (NSF) created the NSF Research Traineeship (NRT) program. To date, over 100 NRT programs have been funded. As these programs are implemented, it is important to assess their progress, successes, and challenges. This presentation describes the ongoing evaluation of one NRT program, "Education Model Program on Water-Energy Research" (or EMPOWER) at Syracuse University. Through seminars, mini-grants, professional development activities, field courses, internship opportunities, and coursework, EMPOWER's goal is to equip students with the skills needed for the range of career options in water and energy. In collaboration with an external evaluator, EMPOWER is examining the fidelity of the program to proposed goals, providing feedback to inform project improvement (formative assessment) and assessing the effectiveness of achieving program goals (summative assessment). Using a convergent parallel mixed method design, qualitative and quantitative data were collected to develop a full assessment of the first year of the program. Evaluation findings have resulted in several positive changes to the program. For example, EMPOWER students perceive themselves to have high technical skills, but the data show that the students do not believe that they have a strong professional network. Based on those findings, EMPOWER offered several professional development events focused on building one's professional network. Preliminary findings have enabled the EMPOWER leadership team to make informed decisions about the ways the program elements can be redesigned to better meet student needs, about how to the make the program more effective, and determine the program elements that may be sustained beyond the funding period. Evaluation of programs like EMPOWER provide essential information to support continual improvement of STEM graduate programs.

DOE handbook: Guide to good practices for training and qualification of maintenance personnel

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

The purpose of this Handbook is to provide contractor training organizations with information that can be used to verify the adequacy of and/or modify existing maintenance training programs, or to develop new training programs. This guide, used in conjunction with facility-specific job analyses, provides a framework for training and qualification programs for maintenance personnel at DOE reactor and nonreactor nuclear facilities. Recommendations for qualification are made in four areas: education, experience, physical attributes, and training. The functional positions of maintenance mechanic, electrician, and instrumentation and control technician are covered by this guide. Sufficient common knowledge and skills were found tomore » include the three disciplines in one guide to good practices. Contents include: qualifications; on-the-job training; trainee evaluation; continuing training; training effectiveness evaluation; and program records. Appendices are included which relate to: administrative training; industrial safety training; fundamentals training; tools and equipment training; facility systems and component knowledge training; facility systems and component skills training; and specialized skills training.« less

Joining technologies for the 1990s: Welding, brazing, soldering, mechanical, explosive, solid-state, adhesive

NASA Technical Reports Server (NTRS)

Buckley, John D. (Editor); Stein, Bland A. (Editor)

1986-01-01

A compilation of papers presented in a joint NASA, American Society for Metals, The George Washington University, American Welding Society, and Society of Manufacturing Engineers Conference on Welding, Bonding, and Fastening at Langley Research Center, Hampton, VA, on October 23 to 25, 1984 is given. Papers were presented on technology developed in current research programs relevant to welding, bonding, and fastening of structural materials required in fabricating structures and mechanical systems used in the aerospace, hydrospace, and automotive industries. Topics covered in the conference included equipment, hardware and materials used when welding, brazing, and soldering, mechanical fastening, explosive welding, use of unique selected joining techniques, adhesives bonding, and nondestructive evaluation. A concept of the factory of the future was presented, followed by advanced welding techniques, automated equipment for welding, welding in a cryogenic atmosphere, blind fastening, stress corrosion resistant fasteners, fastening equipment, explosive welding of different configurations and materials, solid-state bonding, electron beam welding, new adhesives, effects of cryogenics on adhesives, and new techniques and equipment for adhesive bonding.

A Study on Performance and Safety Tests of Electrosurgical Equipment.

PubMed

Tavakoli Golpaygani, A; Movahedi, M M; Reza, M

2016-09-01

Modern medicine employs a wide variety of instruments with different physiological effects and measurements. Periodic verifications are routinely used in legal metrology for industrial measuring instruments. The correct operation of electrosurgical generators is essential to ensure patient's safety and management of the risks associated with the use of high and low frequency electrical currents on human body. The metrological reliability of 20 electrosurgical equipment in six hospitals (3 private and 3 public) was evaluated in one of the provinces of Iran according to international and national standards. The achieved results show that HF leakage current of ground-referenced generators are more than isolated generators and the power analysis of only eight units delivered acceptable output values and the precision in the output power measurements was low. Results indicate a need for new and severe regulations on periodic performance verifications and medical equipment quality control program especially in high risk instruments. It is also necessary to provide training courses for operating staff in the field of meterology in medicine to be acquianted with critical parameters to get accuracy results with operation room equipment.

A description of factors affecting hazardous waste workers' use of respiratory protective equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salazar, M.K.; Takaro, T.K.; Connon, C.

1999-07-01

This article describes the first phase of a study that was designed to gain an understanding of hazardous waste workers' attitudes and beliefs about the use of respiratory protective equipment. Exploratory, open-ended interviews were conducted among 28 respirator users at a US Department of Energy facility. Subjects were asked to describe their knowledge, attitudes, and beliefs about their risks to hazards at their worksites and to discuss their use of respiratory protective equipment. A detailed content analysis of the interviews resulted in the generation of a taxonomy of issues and concerns which fell into three general categories: (1) Knowledge, Beliefs,more » and Attitudes, (2) Physical and Psychological Effects, and (3) External Influences. Knowledge, Beliefs, and Attitudes included Training, Fit Testing, Medical Clearance, Work Exposures, Respirator Use, and Vulnerability to Disease. Physical and Psychological Effects included Somatic/Health Effects, Personal Comfort, Visual Effects, Fatigue, Communication, and Anxiety. External Influences included Structural Environment, Quality and Availability of Equipment, Other PPEs, Co-Worker Influence, Supervisor Influence, and Organizational Culture. The findings from this study have important implications to training and education programs. Effective respiratory protection programs depend on a knowledge of the factors that affect workers' use of equipment. This study suggests that efforts to assure equipment comfort and fit, to assist workers who see and hear less well as a result of their equipment, and to develop strategies to allay worker anxiety when wearing equipment should all be components of a program. An organizational culture that supports and abets the appropriate use of equipment is also a critical element in a successful program.« less

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

NASA Technical Reports Server (NTRS)

Wolf, M.

1981-01-01

The effect of solar cell metallization pattern design on solar cell performance and the costs and performance effects of different metallization processes are discussed. Definitive design rules for the front metallization pattern for large area solar cells are presented. Chemical and physical deposition processes for metallization are described and compared. An economic evaluation of the 6 principal metallization options is presented. Instructions for preparing Format A cost data for solar cell manufacturing processes from UPPC forms for input into the SAMIC computer program are presented.

PR^2EPS: Preparation, recruitment, retention and excellence in the physical sciences

NASA Astrophysics Data System (ADS)

Gallagher, Hugh; Labroo, Sunil; Schaumloffel, John; Bischoff, Paul; Bachman, Nancy

2007-04-01

The PR^2EPS program is a multidisciplinary effort to increase the number of majors attending (and graduating) from SUNY Oneonta with degrees in physics, chemistry, secondary physics or chemistry education and related areas. Components of the program include a walk-in tutoring center, a free, weeklong summer science camp, scholarship opportunities, professional conference experiences, and an equipment loan program for regional secondary science teachers. 2006 was the third year of this NSF-DUE funded program. Evaluation of our progress to date shows that the program is effective at steering students (or at least reinforcing their desire) to studying the sciences in college and retaining them in their science programs. A summary of our goals, challenges and accomplishments, including tutoring center operation and efficacy, activities and operational details for the summer camp, and the overall impact on science programs at a medium sized college will be presented.

Evaluation of Capacity-Building Program of District Health Managers in India: A Contextualized Theoretical Framework

PubMed Central

Prashanth, N. S.; Marchal, Bruno; Kegels, Guy; Criel, Bart

2014-01-01

Performance of local health services managers at district level is crucial to ensure that health services are of good quality and cater to the health needs of the population in the area. In many low- and middle-income countries, health services managers are poorly equipped with public health management capacities needed for planning and managing their local health system. In the south Indian Tumkur district, a consortium of five non-governmental organizations partnered with the state government to organize a capacity-building program for health managers. The program consisted of a mix of periodic contact classes, mentoring and assignments and was spread over 30 months. In this paper, we develop a theoretical framework in the form of a refined program theory to understand how such a capacity-building program could bring about organizational change. A well-formulated program theory enables an understanding of how interventions could bring about improvements and an evaluation of the intervention. In the refined program theory of the intervention, we identified various factors at individual, institutional, and environmental levels that could interact with the hypothesized mechanisms of organizational change, such as staff’s perceived self-efficacy and commitment to their organizations. Based on this program theory, we formulated context–mechanism–outcome configurations that can be used to evaluate the intervention and, more specifically, to understand what worked, for whom and under what conditions. We discuss the application of program theory development in conducting a realist evaluation. Realist evaluation embraces principles of systems thinking by providing a method for understanding how elements of the system interact with one another in producing a given outcome. PMID:25121081

Evaluation of capacity-building program of district health managers in India: a contextualized theoretical framework.

PubMed

Prashanth, N S; Marchal, Bruno; Kegels, Guy; Criel, Bart

2014-01-01

Performance of local health services managers at district level is crucial to ensure that health services are of good quality and cater to the health needs of the population in the area. In many low- and middle-income countries, health services managers are poorly equipped with public health management capacities needed for planning and managing their local health system. In the south Indian Tumkur district, a consortium of five non-governmental organizations partnered with the state government to organize a capacity-building program for health managers. The program consisted of a mix of periodic contact classes, mentoring and assignments and was spread over 30 months. In this paper, we develop a theoretical framework in the form of a refined program theory to understand how such a capacity-building program could bring about organizational change. A well-formulated program theory enables an understanding of how interventions could bring about improvements and an evaluation of the intervention. In the refined program theory of the intervention, we identified various factors at individual, institutional, and environmental levels that could interact with the hypothesized mechanisms of organizational change, such as staff's perceived self-efficacy and commitment to their organizations. Based on this program theory, we formulated context-mechanism-outcome configurations that can be used to evaluate the intervention and, more specifically, to understand what worked, for whom and under what conditions. We discuss the application of program theory development in conducting a realist evaluation. Realist evaluation embraces principles of systems thinking by providing a method for understanding how elements of the system interact with one another in producing a given outcome.

Greenbelt Homes Pilot Program: Summary of Building Envelope Retrofits, Planned HVAC Equipment Upgrades, and Energy Savings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiehagen, J.; Del Bianco, M.; Mallay, D.

2015-05-01

In the fall of 2010, a multiyear pilot energy efficiency retrofit project was undertaken by Greenbelt Homes, Inc, (GHI) a 1,566 home cooperative of circa 1930 and 1940 homes in Greenbelt, Maryland. GHI established this pilot project to serve as a basis for decision making for the rollout of a decade-long community-wide upgrade program that will incorporate energy efficiency improvements to the building envelope and mechanical equipment. It presents a unique opportunity to evaluate and prioritize the wide-range of benefits of high-performance retrofits based on member experience with and acceptance of the retrofit measures implemented during the pilot project. Addressingmore » the complex interactions between benefits, trade-offs, construction methods, project management implications, realistic upfront costs, financing, and other considerations, serves as a case study for energy retrofit projects to include high-performance technologies based on the long-term value to the homeowner. The pilot project focused on identifying the added costs and energy savings benefits of improvements.« less

The NASA Energy Conservation Program

NASA Technical Reports Server (NTRS)

Gaffney, G. P.

1977-01-01

Large energy-intensive research and test equipment at NASA installations is identified, and methods for reducing energy consumption outlined. However, some of the research facilities are involved in developing more efficient, fuel-conserving aircraft, and tradeoffs between immediate and long-term conservation may be necessary. Major programs for conservation include: computer-based systems to automatically monitor and control utility consumption; a steam-producing solid waste incinerator; and a computer-based cost analysis technique to engineer more efficient heating and cooling of buildings. Alternate energy sources in operation or under evaluation include: solar collectors; electric vehicles; and ultrasonically emulsified fuel to attain higher combustion efficiency. Management support, cooperative participation by employees, and effective reporting systems for conservation programs, are also discussed.

Summary of lightning activities by NASA for the Apollo Soyuz test project: Supplement no. 1 to Apollo Soyuz mission evaluation report

NASA Technical Reports Server (NTRS)

1976-01-01

To avoid the possibility of an unnecessary launch delay, a special program was initiated to provide aircraft measurement of electric fields at various altitudes over the Apollo vehicle launch pad. Eight aircraft, each equipped with electric field meters, were used in the program. This program and some of the more important findings are discussed. Also included is a summary of the history of manned space vehicle involvement with lightning, a brief description of the lightning instrumentation in use at KSC (Kennedy Space Center) at the time of the Apollo Soyuz mission and a discussion of the airborne instrumentation and related data.

University of Kansas Medical center Cancer Research Equipment Award Type: Construction Grant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caldwell, Jamie

A major mechanism to strengthen the overall cancer focus of KUCC and expand specific research programs is through targeted recruitment of additional cancer researchers to increase the national and international status of the Cancer Center, enhance the number of NCI/cancer-related grants, fill critical research needs, and enable new collaborative projects. Over the last five years KUCC has demonstrated the ability to recruit nationally recognized basic, translational and clinical scientists to fill key leadership positions and strengthen our research programs. These researchers require new and renovated research facilities require state-of-the-art laboratory equipment. This includes standard equipment for the renovated laboratories andmore » more specialized equipment as part of new investigator start-up packages. This funding is used to support recruitment, facilities, equipment, shared resources, administration, and patient care services. KUCC is committed to recruiting additional cancer researchers to increase the national and international status of the Cancer Center, enhance the number of NCI/cancer-related grants, fill critical research positions and build the four cancer research programs. Each purposeful hire aims to further the scientific vision, mission, and goals of the Cancer Center research programs. The funds requested will be used to supplement the recruitment packages of future cancer center recruits primarily through purchase of key equipment items.« less

40 CFR 1054.626 - What special provisions apply to equipment imported under the Transition Program for Equipment...

Code of Federal Regulations, 2010 CFR

2010-07-01

... EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION ENGINES AND EQUIPMENT Special Compliance Provisions § 1054... provisions of this section and send us an annual report, as follows: (1) Notify the Designated Compliance... and manufacturing equipment. Companies that import equipment into the United States without meeting...

78 FR 72072 - Decision and Order Granting a Waiver to Hussmann From the Department of Energy Commercial...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-02

... procedure for commercial refrigeration equipment because the equipment cannot operate at the specified... Program for certain industrial equipment, which includes commercial refrigeration equipment, the focus of... establish and amend test procedures for commercial refrigeration equipment. (42 U.S.C. 6314(a)(6)(C)) On...

Mississippi Curriculum Framework for Diesel Equipment Technology (CIP: 47.0605--Diesel Engine Mechanic & Repairer). Postsecondary Programs.

ERIC Educational Resources Information Center

Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

This document, which is intended for use by community and junior colleges throughout Mississippi, contains curriculum frameworks for the course sequences in the diesel equipment technology programs cluster. Presented in the introductory section are a description of the program and suggested course sequence. Section I lists baseline competencies,…

"Doing the heavy lifting: health care workers take back their backs".

PubMed

Morse, Tim; Fekieta, Renee; Rubenstein, Harriet; Warren, Nick; Alexander, Darryl; Wawzyniecki, Patricia

2008-01-01

Health care workers have the highest musculoskeletal disorder prevalence and incidence of any occupational/industry group, and patient handling tasks are so biomechanically demanding that they cannot be made safe through the commonly used, technique-oriented methods such as "back school" training programs. Although there is standard-setting activity for "no-lift" programs in some states, there is still no federal standard. Health care worker unions and nurses' associations have begun to take action through training members in equipment need, use, and acceptance in programs to encourage adoption of no-lifting programs. Acceptance of lifting equipment is increasing due to recognition of the high human and economic costs of MSD, consistent documentation of cost savings from no-lift programs, major improvements in lifting equipment, and shortages of health care staff. An action-oriented training program for health care workers is described that provides knowledge about the 1) Scope of the current problem of back injuries in health care, 2) Costs of injuries, both to workers and to the hospital, 3) Elements of a safe patient-handling program, and 4) Success stories. The program also builds skills through: 1) Hands-on experience with safe lifting equipment, and 2) Assessing organizational and union readiness and planning for action at the workplace.

Aeromechanics and man-machine integration technology opportunities for rotorcraft of the 1990s and beyond

NASA Technical Reports Server (NTRS)

Kerr, Andrew W.

1989-01-01

Programs related to rotorcraft aeromechanics and man-machine integration are discussed which will support advanced army rotorcraft design. In aeromechanics, recent advances in computational fluid dynamics will be used to characterize the complex unsteady flowfields of rotorcraft, and a second-generation comprehensive helicopter analysis system will be used along with models of aerodynamics, engines, and control systems to study the structural dynamics of rotor/body configurations. The man-machine integration program includes the development of advanced cockpit design technology and the evaluation of cockpit and mission equipment concepts in a real-time full-combat environment.

Industrial machinery noise impact modeling, volume 1

NASA Astrophysics Data System (ADS)

Hansen, C. H.; Kugler, B. A.

1981-07-01

The development of a machinery noise computer model which may be used to assess the effect of occupational noise on the health and welfare of industrial workers is discussed. The purpose of the model is to provide EPA with the methodology to evaluate the personnel noise problem, to identify the equipment types responsible for the exposure and to assess the potential benefits of a given noise control action. Due to its flexibility in design and application, the model and supportive computer program can be used by other federal agencies, state governments, labor and industry as an aid in the development of noise abatement programs.

Test rig and particulate deposit and cleaning evaluation processes using the same

DOEpatents

Schroder, Mark Stewart; Woodmansee, Donald Ernest; Beadie, Douglas Frank

2002-01-01

A rig and test program for determining the amount, if any, of contamination that will collect in the passages of a fluid flow system, such as a power plant fluid delivery system to equipment assemblies or sub-assemblies, and for establishing methods and processes for removing contamination therefrom. In the presently proposed embodiment, the rig and test programs are adapted in particular to utilize a high-pressure, high-volume water flush to remove contamination from substantially the entire fluid delivery system, both the quantity of contamination and as disposed or deposited within the system.

Apollo experience report: Command and service module communications subsystem

NASA Technical Reports Server (NTRS)

Lattier, E. E., Jr.

1974-01-01

The development of spacecraft communications hardware from design to operation is described. Programs, requirements, specifications, and design approaches for a variety of functions (such as voice, telemetry, television, and antennas) are reviewed. Equipment environmental problems such as vibration, extreme temperature variation, and zero gravity are discussed. A review of the development of managerial techniques used in refining the roles of prime and subcontractors is included. The hardware test program is described in detail as it progressed from breadboard design to manned flight system evaluations. Finally, a series of actions is recommended to managers of similar projects to facilitate administration.

Flight performance measurement utilizing a figure of merit (FOM)

NASA Technical Reports Server (NTRS)

Mosier, Kathleen L.; Zacharias, Greg L.

1993-01-01

One of the goals of the NASA Strategic Behavior/Workload Management Program is to develop standardized procedures for constructing figures of merit (FOMs) that describe minimal criteria for flight task performance, as well as summarize overall performance quality. Such a measure could be utilized for evaluating flight crew performance, for assessing the effectiveness of new equipment or technological innovations, or for measuring performance at a particular airport. In this report, we describe the initial phases in the creation of a FOM to be employed in examining crew performance in NASA-Ames Air Ground Compatibility and Strategic Behavior/Workload Management programs.

77 FR 76825 - Energy Conservation Program: Certification of Commercial and Industrial HVAC, Refrigeration and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-31

... Energy Conservation Program: Certification of Commercial and Industrial HVAC, Refrigeration and Water... provisions for commercial refrigeration equipment; commercial heating, ventilating, air-conditioning (HVAC..., the Department extended the compliance date for certification of commercial refrigeration equipment...

Evaluation of a Participatory Ergonomics Intervention in Small Commercial Construction Firms

PubMed Central

Dale, Ann Marie; Jaegers, Lisa; Welch, Laura; Gardner, Bethany T.; Buchholz, Bryan; Weaver, Nancy; Evanoff, Bradley A.

2017-01-01

Background Work-related musculoskeletal disorders (WMSD) among construction workers remain high. Participatory ergonomics (PE) interventions that engage workers and employers in reducing work injury risks have shown mixed results. Methods Eight-six workers from seven contractors participated in a PE program. A logic model guided the process evaluation and summative evaluation of short term and intermediate impacts and long term outcomes from surveys and field records. Results Process measures showed good delivery of training, high worker engagement, and low contractor participation. Workers’ knowledge improved and workers reported changes to work practices and tools used; contractor provision of appropriate equipment was low (33%). No changes were seen in symptoms or reported physical effort. Conclusions The PE program produced many worker-identified ergonomic solutions, but lacked needed support from contractors. Future interventions should engage higher levels of the construction organizational system to improve contractor involvement for reducing WMSD. PMID:27094450

A definition study of the on-orbit assembly operations for the outboard photovoltaic power modules for Space Station Freedom. M.S. Thesis - Toledo Univ.

NASA Technical Reports Server (NTRS)

Sours, Thomas J.

1989-01-01

A concept is described for the assembly of the outboard PV modules for Space Station Freedom. Analysis of the on-orbit assembly operations was performed using CADAM design graphics software. A scenario for assembly using the various assembly equipment, as currently defined, is described in words, tables and illustrations. This work is part of ongoing studies in the area of space station assembly. The outboard PV module and the assembly equipment programs are all in definition and preliminary design phases. An input is provided to the design process of assembly equipment programs. It is established that the outboard PV module assembly operations can be performed using the assembly equipment currently planned in the Space Station Freedom Program.

Automated data collection equipment for monitoring highway condition.

DOT National Transportation Integrated Search

2005-06-01

This study was conducted to evaluate automated vehicle mounted equipment to collect data on the needs of : Oregons highway inventory. Four vendors accepted invitations to evaluate their equipment. Although ODOT had : conducted a similar evaluation...

44 CFR 302.7 - Use of funds, materials, supplies, equipment, and personnel.

Code of Federal Regulations, 2011 CFR

2011-10-01

... use of civil defense personnel, organizational equipment, materials, and facilities, in preparation..., supplies, equipment, and personnel. 302.7 Section 302.7 Emergency Management and Assistance FEDERAL... EMERGENCY MANAGEMENT ASSISTANCE PROGRAM (EMA) § 302.7 Use of funds, materials, supplies, equipment, and...

40 CFR 89.305 - Equipment measurement accuracy/calibration frequency.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Equipment measurement accuracy... (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES Emission Test Equipment Provisions § 89.305 Equipment measurement accuracy/calibration frequency...

Development and characterization of lubricants for use near nuclear reactors in space vehicles

NASA Technical Reports Server (NTRS)

Robinson, G. L.; Akawie, R. I.; Gardos, M. N.; Krening, K. C.

1972-01-01

The synthesis and evaluation program was conducted to develop wide-temperature range lubricants suitable for use in space vehicles particularly in the vicinity of nuclear reactors. Synthetic approaches resulted in nonpolymeric, large molecular weight materials, all based on some combination of siloxane and aromatic groups. Evaluation of these materials indicated that certain tetramethyl and hexamethyl disiloxanes containing phenyl thiophenyl substituents are extremely promising with respect to radiation stability, wide temperature range, good lubricity, oxidation resistance and additive acceptance. The synthesis of fluids is discussed, and the equipment and methods used in evaluation are described, some of which were designed to evaluate micro-quantities of the synthesized lubricants.

Application of a Systems Engineering Approach to Support Space Reactor Development

NASA Astrophysics Data System (ADS)

Wold, Scott

2005-02-01

In 1992, approximately 25 Russian and 12 U.S. engineers and technicians were involved in the transport, assembly, inspection, and testing of over 90 tons of Russian equipment associated with the Thermionic System Evaluation Test (TSET) Facility. The entire Russian Baikal Test Stand, consisting of a 5.79 m tall vacuum chamber and related support equipment, was reassembled and tested at the TSET facility in less than four months. In November 1992, the first non-nuclear operational test of a complete thermionic power reactor system in the U.S. was accomplished three months ahead of schedule and under budget. A major factor in this accomplishment was the application of a disciplined top-down systems engineering approach and application of a spiral development model to achieve the desired objectives of the TOPAZ International Program (TIP). Systems Engineering is a structured discipline that helps programs and projects conceive, develop, integrate, test and deliver products and services that meet customer requirements within cost and schedule. This paper discusses the impact of Systems Engineering and a spiral development model on the success of the TOPAZ International Program and how the application of a similar approach could help ensure the success of future space reactor development projects.

Descriptive Summaries of the Research Development Test & Evaluation Army Appropriation FY 1983. Supporting Data FY 1983, Budget Estimate Submitted to Congress February 1982. Volume II.

DTIC Science & Technology

1982-02-01

Defense (BHD) Advanced Technology Program is a broadly based rsearch and development effort designed to exploit new and emerging technologies...11-363 DK13 NON -COMMUNICATIONS ELECTRONIC COUNTERMEASURES SYSTEMS .............................. .11-368 DK14 EXPENDABLE JAMMERS...NAVSTAR GLOBAL POSITIONING SYSTEMS (GPS) USER EQUIPMENT .................................. 111-366 DEFENSEWIDE MISSION SUPPORT 6.37.38.A NON -SYSTEMS

Skylab

NASA Image and Video Library

1970-01-01

This 1970 photograph shows equipment for the Skylab's Sleep Monitoring Experiment (M133), a medical evaluation designed to objectively determine the amount and quality of crewmembers' inflight sleep. The experiment monitored and recorded electroencephalographic (EEG) and electrooculographic (EOG) activity during astronauts' sleep periods. One of the astronauts was selected for this experiment and wore a fitted cap during his sleep periods. The Marshall Space Flight Center had program management responsibility for the development of Skylab hardware and experiments.

RESEARCH AND DEVELOPMENT ON ADVANCED GRAPHITE MATERIALS. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1962-04-01

A review is given of activities over the period October 15, 1960 to October 15, 1961 on a three year program for the research and development of materials, experimental techniques, and equipment for development of premium quality, reproducible graphite-base materials suitable for missile and astronautic applications. Progress is reported on research and development in the study areas of raw materials, fabrication, and material characterization and evaluation. (auth)

Evaluating the Tradeoffs Between Dollars Spent and Lives saved in Military Settings

DTIC Science & Technology

2013-11-18

data needed , and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this...Programs that improve workplace safety have costs. Firms may need to purchase additional equipment or protective devices, install machine guards...employers the costs may be slight. Because of the inherent dangers in production, firms in mining, logging, fishing, and construction will need to

The Management of Defense System and Equipment Training: A Guide for the Naval Education and Training Command

DTIC Science & Technology

1977-07-01

SYSTEM EVOLUTION 4- LEVEL 1 LEVEL 2 LEVEL 3 ,_J LEVEL 4 PERSONNEL ENTRY FACTORS (SKILL, KNOWLEDGE, EXPERIENCE ) HIGH HIGH AND ABOVE...system) and their associated program characteristics (cost, schedules, and operational parameters) based on a combination of analyses, experiments , and...Naval Operations Appropriations (blue doll ars) Appropriation Abbreviation Sponsor Research, Development, Test and Evaluation, Navy RDT&EN ASN (R&D

A Report and Evaluation of the OECA-Integrated Projects V.T.R. Project at Chinguacousy Public Library in Bramalea, Ontario, January 1974-June 1974.

ERIC Educational Resources Information Center

Henderson, John; And Others

In 1974, the Ontario Educational Communications Authority (OECA) undertook a study to measure the feasibility of loaning video tape recording equipment and video tapes to home users. A pilot program in one branch library found that, with the assistance of a video instruction package and an instructional booklet, users quickly mastered the…

Development and Exchange of Instructional Resources in Water Quality Control Programs, III: Selecting Audio-Visual Equipment.

ERIC Educational Resources Information Center

Moon, Donald K.

This document is one in a series of reports which reviews instructional materials and equipment and offers suggestions about how to select equipment. Topics discussed include: (1) the general criteria for audio-visual equipment selection such as performance, safety, comparability, sturdiness and repairability; and (2) specific equipment criteria…

The evolution of a health hazard assessment database management system for military weapons, equipment, and materiel.

PubMed

Murnyak, George R; Spencer, Clark O; Chaney, Ann E; Roberts, Welford C

2002-04-01

During the 1970s, the Army health hazard assessment (HHA) process developed as a medical program to minimize hazards in military materiel during the development process. The HHA Program characterizes health hazards that soldiers and civilians may encounter as they interact with military weapons and equipment. Thus, it is a resource for medical planners and advisors to use that can identify and estimate potential hazards that soldiers may encounter as they train and conduct missions. The U.S. Army Center for Health Promotion and Preventive Medicine administers the program, which is integrated with the Army's Manpower and Personnel Integration program. As the HHA Program has matured, an electronic database has been developed to record and monitor the health hazards associated with military equipment and systems. The current database tracks the results of HHAs and provides reporting designed to assist the HHA Program manager in daily activities.

Controlling mechanisms over the internet

NASA Astrophysics Data System (ADS)

Lumia, Ronald

1997-01-01

The internet, widely available throughout the world, can be used to control robots, machine tools, and other mechanisms. This paper will describe a low-cost virtual collaborative environment (VCE) which will connect users with distant equipment. The system is based on PC technology, and incorporates off-line-programming with on-line execution. A remote user programs the systems graphically and simulates the motions and actions of the mechanism until satisfied with the functionality of the program. The program is then transferred from the remote site to the local site where the real equipment exists. At the local site, the simulation is run again to check the program from a safety standpoint. Then, the local user runs the program on the real equipment. During execution, a camera in the real workspace provides an image back to the remote user through a teleconferencing system. The system costs approximately 12,500 dollars and represents a low-cost alternative to the Sandia National Laboratories VCE.

Systematic Model for Validating Equipment Uses in Selected Marketing and Distribution Education Programs. Final Report, February 1, 1980-June 30, 1981.

ERIC Educational Resources Information Center

Gildan, Kate; Buckner, Leroy

Research was conducted to provide a model for selecting equipment for marketing and distributive education programs that was required for the development of the skills or competencies needed to perform in marketing and distribution occupation. A research of the literature identified both competency statements for three program areas--Fashion…

A STUDY TO DETERMINE THE NEED AND TYPE OF TRAINING PROGRAM FOR AGRICULTURAL PUBLIC SERVICE TECHNICIANS.

ERIC Educational Resources Information Center

Mount San Antonio Coll., Walnut, CA.

THE OBJECTIVE WAS TO STUDY AGRICULTURAL PUBLIC SERVICE TECHNICIANS IN THE STATE TO DETERMINE (1) THE NUMBER EMPLOYED BY FEDERAL, STATE, AND LOCAL AGENCIES, (2) EXISTING SHORTAGES, (3) THE TYPE OF TRAINING NEEDED, (4) DESIRABILITY OF TRAINING PROGRAM AT MT. SAN ANTONIO COLLEGE, (5) EQUIPMENT AND PROGRAMS NEEDED, AND (6) EQUIPMENT NEEDED IN A…

Mechanization in a New Medical School Library II. Serials and Circulation

PubMed Central

Payne, Ladye Margarete; Small, Louise; Divett, Robert T.

1966-01-01

The serials and circulation phases of the data-processing system in use at the University of New Mexico Library of the Medical Sciences are described. The development of the programs is also reported. The serials program uses simple punched card equipment. The circulation program uses the IBM 357 Data Collection System and punched card data-processing equipment. Images PMID:5921473

Tools for Schools. Defense Industrial Reserve Loan Program. Public Law 93-155, 93rd Congress.

ERIC Educational Resources Information Center

Defense Logistics Agency (DOD), Memphis, TN.

This brochure describes the "Tools for Schools" Loan Program and includes guidelines for preparation of an application for a loan of industrial manufacturing equipment from the Defense Industrial Reserve (DIR). The first section is in question-and-answer form and describes the program through which equipment from DIR may be loaned to any…

Hardware Development Process for Human Research Facility Applications

NASA Technical Reports Server (NTRS)

Bauer, Liz

2000-01-01

The simple goal of the Human Research Facility (HRF) is to conduct human research experiments on the International Space Station (ISS) astronauts during long-duration missions. This is accomplished by providing integration and operation of the necessary hardware and software capabilities. A typical hardware development flow consists of five stages: functional inputs and requirements definition, market research, design life cycle through hardware delivery, crew training, and mission support. The purpose of this presentation is to guide the audience through the early hardware development process: requirement definition through selecting a development path. Specific HRF equipment is used to illustrate the hardware development paths. The source of hardware requirements is the science community and HRF program. The HRF Science Working Group, consisting of SCientists from various medical disciplines, defined a basic set of equipment with functional requirements. This established the performance requirements of the hardware. HRF program requirements focus on making the hardware safe and operational in a space environment. This includes structural, thermal, human factors, and material requirements. Science and HRF program requirements are defined in a hardware requirements document which includes verification methods. Once the hardware is fabricated, requirements are verified by inspection, test, analysis, or demonstration. All data is compiled and reviewed to certify the hardware for flight. Obviously, the basis for all hardware development activities is requirement definition. Full and complete requirement definition is ideal prior to initiating the hardware development. However, this is generally not the case, but the hardware team typically has functional inputs as a guide. The first step is for engineers to conduct market research based on the functional inputs provided by scientists. CommerCially available products are evaluated against the science requirements as well as modifications needed to meet program requirements. Options are consolidated and the hardware development team reaches a hardware development decision point. Within budget and schedule constraints, the team must decide whether or not to complete the hardware as an in-house, subcontract with vendor, or commercial-off-the-shelf (COTS) development. An in-house development indicates NASA personnel or a contractor builds the hardware at a NASA site. A subcontract development is completed off-site by a commercial company. A COTS item is a vendor product available by ordering a specific part number. The team evaluates the pros and cons of each development path. For example, in-bouse developments utilize existing corporate knowledge regarding bow to build equipment for use in space. However, technical expertise would be required to fully understand the medical equipment capabilities, such as for an ultrasound system. It may require additional time and funding to gain the expertise that commercially exists. The major benefit of subcontracting a hardware development is the product is delivered as an end-item and commercial expertise is utilized. On the other hand, NASA has limited control over schedule delays. The final option of COTS or modified COTS equipment is a compromise between in-house and subcontracts. A vendor product may exist that meets all functional requirements but req uires in-house modifications for successful operation in a space environment. The HRF utilizes equipment developed using all of the paths described: inhouse, subcontract, and modified COTS.

EPA requirements and programs

NASA Technical Reports Server (NTRS)

Koutsandreas, J. D.

1975-01-01

The proposed ERTS-DCS system is designed to allow EPA the capability to evaluate, through demonstrable hardware, the effectiveness of automated data collection techniques. The total effectiveness of any system is dependent upon many factors which include equipment cost, installation, maintainability, logistic support, growth potential, flexibility and failure rate. This can best be accomplished by installing the system at an operational environmental control agency (CAMP station) to insure that valid data is being obtained and processed. Consequently, it is imperative that the equipment interface must not compromise the validity of the sensor data nor should the experimental system effect the present operations of the CAMP station. Since both the system which is presently in use and the automatic system would be in operation in parallel, conformation and comparison are readily obtained.

Research program for experiment M133

NASA Technical Reports Server (NTRS)

Frost, J. D., Jr.

1972-01-01

The development of the automatic data-acquisition and sleep-analysis system is reported. The purpose was consultation and evaluation in the transition of the Skylab M133 Sleep-Monitoring Experiment equipment from prototype of flight status; review of problems associated with acquisition and on-line display of data in near-real time via spacecraft telemetry; and development of laboratory facilities and design of equipment to assure reliable playback and analysis of analog data. The existing prototype system modified, and the changes improve the performance of the analysis circuitry and increase its reliability. These modifications are useful for pre- and postflight analysis, but are not now proposed for the inflight system. There were improvements in the EEG recording cap, some of which will be incorporated into the flight hardware.

Space transportation system payload interface verification

NASA Technical Reports Server (NTRS)

Everline, R. T.

1977-01-01

The paper considers STS payload-interface verification requirements and the capability provided by STS to support verification. The intent is to standardize as many interfaces as possible, not only through the design, development, test and evaluation (DDT and E) phase of the major payload carriers but also into the operational phase. The verification process is discussed in terms of its various elements, such as the Space Shuttle DDT and E (including the orbital flight test program) and the major payload carriers DDT and E (including the first flights). Five tools derived from the Space Shuttle DDT and E are available to support the verification process: mathematical (structural and thermal) models, the Shuttle Avionics Integration Laboratory, the Shuttle Manipulator Development Facility, and interface-verification equipment (cargo-integration test equipment).

Aging Aircraft Subsystems. Equipment Life Extension within the Tornado Program

DTIC Science & Technology

2000-10-01

establish whether of trained personal. an equipment is already life expired or not. Maintenance documentation Repairs and concessions Existing...to be replaced equipment will lead over time to a degradation of the functional check seals. This means that the older the equipment stays inservice

10 CFR 431.404 - Imported equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Imported equipment. 431.404 Section 431.404 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT General Provisions § 431.404 Imported equipment. (a) Under sections 331 and 345 of the Act, any...

77 FR 75400 - Labeling Requirements for Commercial and Industrial Equipment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-20

.... EERE-2012-BT-NOA-0037] RIN 1904-AC84 Labeling Requirements for Commercial and Industrial Equipment... standards for certain commercial and industrial equipment, and requires the Department of Energy (DOE) to administer an energy conservation program for the equipment, including the development of labeling...

EPA USDA Agricultural Equipment Statement of Principles

EPA Pesticide Factsheets

The Agricultural Equipment Statement of Principles was developed jointly between EPA and USDA at the request of agriculture industry stakeholders seeking support for programs to assist farmers looking to invest in cleaner agricultural equipment

Fine urban and precursor emissions control for diesel urban transit buses.

PubMed

Lanni, Thomas

2003-01-01

Particulate emission from diesel engines is one of the most important pollutants in urban areas. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled "Clean Diesel Air Quality Demonstration Program" has been initiated by the New York City Metropolitan Transit Authority (MTA) under the supervision of New York State Department of Environmental Conservation and with active participation from Johnson Matthey, Corning, Equilon, Environment Canada and RAD Energy. Under this program, several MTA transit buses with DDC Series 50 engines were equipped with Continuously Regenerating Technology (CRTTM) particulate filter systems and have been operated with ultra low sulfur diesel (<30 ppm S) in transit service in Manhattan since February 2000. These buses were evaluated over a 9-month period for durability and maintainability of the particulate filter. In addition, an extensive emissions testing program was carried out using transient cycles on a chassis dynamometer to evaluate the emissions reductions obtained with the particle filter. In this paper, the emissions testing data from the Clean Diesel Air Quality Demonstration Program are discussed in detail.

Effects of Budget Reductions on Army Acquisition Support of Equipping and Modernization Goals

DTIC Science & Technology

2015-04-16

overall Army budgets are significantly reduced (34% since 2008), maintaining the entire equipment portfolio reduces the funding available to meet...the Mission Command portfolio , examine their impact on equipping and modernization, and make recommendations on how to divest the equipment no longer... portfolio of equipment being managed and the link to the new Defense guidance and Army equipping guidance and modernization plans. Any systems or programs

Stakeholders' Perspectives About and Priorities for Economic Evaluation of Health and Safety Programs in Healthcare.

PubMed

Tompa, Emile; de Boer, Henriette; Macdonald, Sara; Alamgir, Hasanat; Koehoorn, Mieke; Guzman, Jaime

2016-04-01

This study identified and prioritized resources and outcomes that should be considered in more comprehensive and scientifically rigorous health and safety economic evaluations according to healthcare sector stakeholders. A literature review and stakeholder interviews identified candidate resources and outcomes and then a Delphi panel ranked them. According to the panel, the top five resources were (a) health and safety staff time; (b) training workers; (c) program planning, promotion, and evaluation costs; (d) equipment purchases and upgrades; and (e) administration costs. The top five outcomes were (a) number of injuries, illnesses, and general sickness absences; (b) safety climate; (c) days lost due to injuries, illnesses, and general sickness absences; (d) job satisfaction and engagement; and (e) quality of care and patient safety. These findings emphasize stakeholders' stated priorities and are useful as a benchmark for assessing the quality of health and safety economic evaluations and the comprehensiveness of these findings. © 2016 The Author(s).

ENVIRONMENTAL TECHNOLOGY VERIFICATION COATINGS AND COATING EQUIPMENT PROGRAM (ETV CCEP) HIGH TRANSFER EFFICIENCE SPRAY EQUIPMENT--GENERIC VERIFICATION PROTOCOL

EPA Science Inventory

The Environmental Technology Verification (ETV) Program has been established to verify the performance characteristics of innovative environmental technologies and report this objective information, thus, accelerating the entrance of these new technologies into the marketplace. V...

Evaluation of Quality-Assurance/Quality-Control Data Collected by the U.S. Geological Survey from Wells and Springs between the Southern Boundary of the Idaho National Engineering and Environmental Laboratory and the Hagerman Area, Idaho, 1989 through 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, L.M.; Bartholomay, R.C.; Campbell, L.J.

1998-10-01

The U.S. Geological (USGS) and the Idaho Department of Water Resources, in cooperation with the U.S. Department of Energy, collected and analyzed water samples to monitor the water quality of the Snake River Plain aquifer from the southern boundary of the Idaho National Engineering and Environmental Laboratory to the Hagerman area, Idaho. Concurrently, replicate samples and blank samples were collected and analyzed as part of the quality-assurance/quality-control program. Samples were analyzed from inorganic constituents, gross radioactivity and radionuclides, organic constituents, and stable isotopes. To evaluate the precision of field and laboratory methods, analytical results of the water-quality and replicate samplesmore » were compared statistically for equivalence on the basis of the precision associated with each result. Statistical comparisons of the data indicated that 95 percent of the results of the replicate pairs were equivalent. Blank-sample analytical results indicated th at the inorganic blank water and volatile organic compound blank water from the USGS National Water Quality Laboratory and the distilled water from the Idaho Department of Water Resources were suitable for blanks; blank water from other sources was not. Equipment-blank analytical results were evaluated to determine if a bias had been introduced and possible sources of bias. Most equipment blanks were analyzed for trace elements and volatile organic compounds; chloroform was found in one equipment blank. Two of the equipment blanks were prepared after collection and analyses of the water-quality samples to determine whether contamination had been introduced during the sampling process. Results of one blank indicated that a hose used to divert water away from pumps and electrical equipment had contaminated the samples with some volatile organic compounds. Results of the other equipment blank, from the apparatus used to filter dissolved organic carbon samples, indicated that the filtering apparatus did not affect water-quality samples.« less

47 CFR 76.1206 - Equipment sale or lease charge subsidy prohibition.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Equipment sale or lease charge subsidy... Devices § 76.1206 Equipment sale or lease charge subsidy prohibition. Multichannel video programming... subscribers, shall adhere to the standards reflected therein relating to rates for equipment and installation...

40 CFR 65.117 - Alternative means of emission limitation: Batch processes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) CONSOLIDATED FEDERAL AIR RULE Equipment Leaks § 65.117 Alternative means... section provide the options of pressure testing or monitoring the equipment for leaks. The owner or... pressure-tested for leaks before regulated material is first fed to the equipment and the equipment is...

40 CFR 1068.210 - What are the provisions for exempting test engines/equipment?

Code of Federal Regulations, 2013 CFR

2013-07-01

... NONROAD PROGRAMS Exemptions and Exclusions § 1068.210 What are the provisions for exempting test engines/equipment? (a) We may exempt engines/equipment that you will use for research, investigations, studies... test engines/equipment? 1068.210 Section 1068.210 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 1068.210 - What are the provisions for exempting test engines/equipment?

Code of Federal Regulations, 2014 CFR

2014-07-01

... NONROAD PROGRAMS Exemptions and Exclusions § 1068.210 What are the provisions for exempting test engines/equipment? (a) We may exempt engines/equipment that you will use for research, investigations, studies... test engines/equipment? 1068.210 Section 1068.210 Protection of Environment ENVIRONMENTAL PROTECTION...

40 CFR 1068.210 - What are the provisions for exempting test engines/equipment?

Code of Federal Regulations, 2012 CFR

2012-07-01

... NONROAD PROGRAMS Exemptions and Exclusions § 1068.210 What are the provisions for exempting test engines/equipment? (a) We may exempt engines/equipment that you will use for research, investigations, studies... test engines/equipment? 1068.210 Section 1068.210 Protection of Environment ENVIRONMENTAL PROTECTION...

75 FR 51419 - Requirements for Intermodal Equipment Providers and for Motor Carriers and Drivers Operating...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-20

... inspection, repair, and maintenance of intermodal equipment (IME), specifically with respect to the..., by the Ocean Carrier Equipment Management Association (OCEMA) and the Institute of International... equipment providers (IEPs) to have in place inspection, repair and maintenance programs, and a process for...

40 CFR 63.1159 - Operational and equipment standards for existing, new, or reconstructed sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... atmosphere shall be equipped with a local fume capture system, ventilated through an air pollution control... pollution control equipment and monitoring equipment in a manner consistent with safety and good air... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS...

40 CFR 63.1159 - Operational and equipment standards for existing, new, or reconstructed sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... atmosphere shall be equipped with a local fume capture system, ventilated through an air pollution control... pollution control equipment and monitoring equipment in a manner consistent with safety and good air... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS...

40 CFR 1039.625 - What requirements apply under the program for equipment-manufacturer flexibility?

Code of Federal Regulations, 2012 CFR

2012-07-01

... NONROAD COMPRESSION-IGNITION ENGINES Special Compliance Provisions § 1039.625 What requirements apply... manufacturers to produce equipment with engines that are subject to less stringent emission standards after the... such equipment without manufacturing it. Engines and equipment you produce under this section are...

40 CFR 1039.625 - What requirements apply under the program for equipment-manufacturer flexibility?

Code of Federal Regulations, 2013 CFR

2013-07-01

... NONROAD COMPRESSION-IGNITION ENGINES Special Compliance Provisions § 1039.625 What requirements apply... manufacturers to produce equipment with engines that are subject to less stringent emission standards after the... such equipment without manufacturing it. Engines and equipment you produce under this section are...

34 CFR 74.34 - Equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... following standards: (1) For equipment with a current per unit fair market value of $5000 or more, the... the cost of the original project or program to the current fair market value of the equipment. (2) If... the current fair market value of the equipment, plus any reasonable shipping or interim storage costs...

7 CFR 550.38 - Equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... or the method used to determine current fair market value where a Cooperator compensates the REE... the current fair market value of the equipment. If the Cooperator has no need for the equipment, the... cost of the original project or program to the current fair market value of the equipment, plus any...

78 FR 24428 - P25 Compliance Assessment Program for Communications Equipment

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-25

... Communications Equipment AGENCY: Science and Technology Directorate, Department of Homeland Security. ACTION... for ensuring that communications equipment that is declared by the manufacturer to be P25 compliant in... developed by DHS and the National Institute of Standards and Technology (NIST) to identify equipment that...

Acquisition of Cleanroom Research Equipment to Support Ongoing DoD Programs at ASU

DTIC Science & Technology

2017-12-12

Report: Acquisition of cleanroom research equipment to support ongoing DoD programs at ASU The views, opinions and/or findings contained in this report...documentation. 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS (ES) U.S. Army Research Office P.O. Box 12211 Research Triangle Park, NC 27709...Agreement Number: W911NF-16-1-0354 Organization: Arizona State University Title: Acquisition of cleanroom research equipment to support ongoing DoD

Application of USNRC NUREG/CR-6661 and draft DG-1108 to evolutionary and advanced reactor designs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang 'Apollo', Chen

2006-07-01

For the seismic design of evolutionary and advanced nuclear reactor power plants, there are definite financial advantages in the application of USNRC NUREG/CR-6661 and draft Regulatory Guide DG-1108. NUREG/CR-6661, 'Benchmark Program for the Evaluation of Methods to Analyze Non-Classically Damped Coupled Systems', was by Brookhaven National Laboratory (BNL) for the USNRC, and Draft Regulatory Guide DG-1108 is the proposed revision to the current Regulatory Guide (RG) 1.92, Revision 1, 'Combining Modal Responses and Spatial Components in Seismic Response Analysis'. The draft Regulatory Guide DG-1108 is available at http://members.cox.net/apolloconsulting, which also provides a link to the USNRC ADAMS site to searchmore » for NUREG/CR-6661 in text file or image file. The draft Regulatory Guide DG-1108 removes unnecessary conservatism in the modal combinations for closely spaced modes in seismic response spectrum analysis. Its application will be very helpful in coupled seismic analysis for structures and heavy equipment to reduce seismic responses and in piping system seismic design. In the NUREG/CR-6661 benchmark program, which investigated coupled seismic analysis of structures and equipment or piping systems with different damping values, three of the four participants applied the complex mode solution method to handle different damping values for structures, equipment, and piping systems. The fourth participant applied the classical normal mode method with equivalent weighted damping values to handle differences in structural, equipment, and piping system damping values. Coupled analysis will reduce the equipment responses when equipment, or piping system and structure are in or close to resonance. However, this reduction in responses occurs only if the realistic DG-1108 modal response combination method is applied, because closely spaced modes will be produced when structure and equipment or piping systems are in or close to resonance. Otherwise, the conservatism in the current Regulatory Guide 1.92, Revision 1, will overshadow the advantage of coupled analysis. All four participants applied the realistic modal combination method of DG-1108. Consequently, more realistic and reduced responses were obtained. (authors)« less

Testing and Evaluation of Passive Radiation Detection Equipment for Homeland Security

DOE PAGES

West, David L.; Wood, Nathan L.; Forrester, Christina D.

2017-12-01

This article is concerned with test and evaluation methods for passive radiation detection equipment used in homeland security applications. The different types of equipment used in these applications are briefly reviewed and then test and evaluation methods discussed. The primary emphasis is on the test and evaluation standards developed by the American National Standards Institute’s N42 committees. Commonalities among the standards are then reviewed as well as examples of unique aspects for specific equipment types. Throughout, sample test configurations and results from testing and evaluation at Oak Ridge National Laboratory are given. The article concludes with a brief discussion ofmore » typical tests and evaluations not covered by the N42 standards and some examples of test and evaluation that involve the end users of the equipment.« less

Testing and Evaluation of Passive Radiation Detection Equipment for Homeland Security

DOE Office of Scientific and Technical Information (OSTI.GOV)

West, David L.; Wood, Nathan L.; Forrester, Christina D.

This article is concerned with test and evaluation methods for passive radiation detection equipment used in homeland security applications. The different types of equipment used in these applications are briefly reviewed and then test and evaluation methods discussed. The primary emphasis is on the test and evaluation standards developed by the American National Standards Institute’s N42 committees. Commonalities among the standards are then reviewed as well as examples of unique aspects for specific equipment types. Throughout, sample test configurations and results from testing and evaluation at Oak Ridge National Laboratory are given. The article concludes with a brief discussion ofmore » typical tests and evaluations not covered by the N42 standards and some examples of test and evaluation that involve the end users of the equipment.« less

Medical technology advances from space research.

NASA Technical Reports Server (NTRS)

Pool, S. L.

1971-01-01

NASA-sponsored medical R & D programs for space applications are reviewed with particular attention to the benefits of these programs to earthbound medical services and to the general public. Notable among the results of these NASA programs is an integrated medical laboratory equipped with numerous advanced systems such as digital biotelemetry and automatic visual field mapping systems, sponge electrode caps for electroencephalograms, and sophisticated respiratory analysis equipment.

Environmental Technology Verification Coatings and Coating Equipment Program (ETV CCEP) High Transfer Efficiency Spray Equipment--Generic Verification Protocol

EPA Science Inventory

The Environmental Technology Verification (ETV) Program has been established by the U.S. Environmental Protection Agency (EPA) to verify the performance characteristics of innovative environmental technologies across all media and report this objective information to the states, ...

Health center streamlines use of audiovisual aids.

PubMed

Brantz, M H

1978-09-01

Audiovisual aids and programs can be used to help provide effective and efficient in-hospital continuing education programs. The cost of audiovisual equipment can be minimized and use can be maximized by implementing standardization policies that identify and simplify the number and types of equipment to be purchased.

41 CFR 109-50.102 - General.

Code of Federal Regulations, 2010 CFR

2010-07-01

... DISPOSAL AUTHORITIES 50.1-Used Energy-Related Laboratory Equipment Grant Program § 109-50.102 General. DOE, to encourage research and development in the field of energy, awards grants of excess energy-related laboratory equipment to eligible institutions for use in energy-oriented educational programs. Under the Used...

A study on the real-time reliability of on-board equipment of train control system

NASA Astrophysics Data System (ADS)

Zhang, Yong; Li, Shiwei

2018-05-01

Real-time reliability evaluation is conducive to establishing a condition based maintenance system for the purpose of guaranteeing continuous train operation. According to the inherent characteristics of the on-board equipment, the connotation of reliability evaluation of on-board equipment is defined and the evaluation index of real-time reliability is provided in this paper. From the perspective of methodology and practical application, the real-time reliability of the on-board equipment is discussed in detail, and the method of evaluating the realtime reliability of on-board equipment at component level based on Hidden Markov Model (HMM) is proposed. In this method the performance degradation data is used directly to realize the accurate perception of the hidden state transition process of on-board equipment, which can achieve a better description of the real-time reliability of the equipment.

Federal incentives for industrial modernization: Historical review and future opportunities

NASA Technical Reports Server (NTRS)

Coleman, Sandra C.; Batson, Robert G.

1987-01-01

Concerns over the aging of the U.S. aerospace industrial base led DOD to introduce first its Technology Modernization (Tech Mod) Program, and more recently the Industrial Modernization Incentive Program (IMIP). These incentives include productivity shared savings rewards, contractor investment protection to allow for amortization of plant and equipment, and subcontractor/vendor participation. The purpose here is to review DOD IMIP and to evaluate whether a similar program is feasible for NASA and other non-DOD agencies. The IMIP methodology is of interest to industrial engineers because it provides a structured, disciplined approach to identifying productivity improvement opportunities and documenting their expected benefit. However, it is shown that more research on predicting and validating cost avoidance is needed.

A Controlled Evaluation of a High School Biomedical Pipeline Program: Design and Methods

NASA Astrophysics Data System (ADS)

Winkleby, Marilyn A.; Ned, Judith; Ahn, David; Koehler, Alana; Fagliano, Kathleen; Crump, Casey

2014-02-01

Given limited funding for school-based science education, non-school-based programs have been developed at colleges and universities to increase the number of students entering science- and health-related careers and address critical workforce needs. However, few evaluations of such programs have been conducted. We report the design and methods of a controlled trial to evaluate the Stanford Medical Youth Science Program's Summer Residential Program (SRP), a 25-year-old university-based biomedical pipeline program. This 5-year matched cohort study uses an annual survey to assess educational and career outcomes among four cohorts of students who participate in the SRP and a matched comparison group of applicants who were not chosen to participate in the SRP. Matching on sociodemographic and academic background allows control for potential confounding. This design enables the testing of whether the SRP has an independent effect on educational- and career-related outcomes above and beyond the effects of other factors such as gender, ethnicity, socioeconomic background, and pre-intervention academic preparation. The results will help determine which curriculum components contribute most to successful outcomes and which students benefit most. After 4 years of follow-up, the results demonstrate high response rates from SRP participants and the comparison group with completion rates near 90 %, similar response rates by gender and ethnicity, and little attrition with each additional year of follow-up. This design and methods can potentially be replicated to evaluate and improve other biomedical pipeline programs, which are increasingly important for equipping more students for science- and health-related careers.

A CONTROLLED EVALUATION OF A HIGH SCHOOL BIOMEDICAL PIPELINE PROGRAM: DESIGN AND METHODS.

PubMed

Winkleby, Marilyn A; Ned, Judith; Ahn, David; Koehler, Alana; Fagliano, Kathleen; Crump, Casey

2014-02-01

Given limited funding for school-based science education, non-school-based programs have been developed at colleges and universities to increase the number of students entering science- and health-related careers and address critical workforce needs. However, few evaluations of such programs have been conducted. We report the design and methods of a controlled trial to evaluate the Stanford Medical Youth Science Program's Summer Residential Program (SRP), a 25-year-old university-based biomedical pipeline program. This 5-year matched cohort study uses an annual survey to assess educational and career outcomes among four cohorts of students who participate in the SRP and a matched comparison group of applicants who were not chosen to participate in the SRP. Matching on sociodemographic and academic background allows control for potential confounding. This design enables the testing of whether the SRP has an independent effect on educational- and career-related outcomes above and beyond the effects of other factors such as gender, ethnicity, socioeconomic background, and pre-intervention academic preparation. The results will help determine which curriculum components contribute most to successful outcomes and which students benefit most. After 4 years of follow-up, the results demonstrate high response rates from SRP participants and the comparison group with completion rates near 90%, similar response rates by gender and ethnicity, and little attrition with each additional year of follow-up. This design and methods can potentially be replicated to evaluate and improve other biomedical pipeline programs, which are increasingly important for equipping more students for science- and health-related careers.

Department of Defense In-House RDT and E Activities

DTIC Science & Technology

1972-10-30

test and evaluation (RDTJE). In addition, they briefly described each activ "ty’s mission, current important programs. functions, and equipment...capabilities. The statistical data relate to the past and current fiscal years, i.e. 1972 and 1973. Each in-house RDTfE activity of the Department of Defense...manual correction of typo- graphical errors and clarification of obscure abbreviations and contrac- tions. All current DoD RDT&E activities are

Facility Reliability and Maintainability: An Investigation of the Air Force Civil Engineering Recurring Work Program

DTIC Science & Technology

1989-09-01

18:2). A recent survey by the Strategic Air Command (SAC) Mechanical Fquipment Management Evaluation Team ( MEMET ) determined that equipment was...identified by MEMET included Maintenance Action Sheets (MAS) that reported work which was not completed, and other MAS which annotated recurring work...readily apparent. Problem Military. The Deputy Chief of Staff for Engineering and Services, HQ SAC, established the MEMET in 1984 in response to a

Interagency Evaluation of the Section 1206 Global Train and Equip Program

DTIC Science & Technology

2009-08-31

Capabilities, Joint Staff, U.S. Africa Command, U.S. Central Command, U.S Joint Forces Command, U.S. Pacific Command, U.S. Southern Command, U.S. Special...Intensity Conflict & Interdependent Capabilities; Commanders of U.S. Africa Command, U.S. Central Command, U.S. Joint Forces Command, U.S. Pacific... Central Command, commented that coordinating the Section 1206 project proposal with the partner nation prior to submission would inflate the

Breadboard stellar tracker system test report, volume 2

NASA Technical Reports Server (NTRS)

1981-01-01

Complete data from a test program designed to evaluate the performance of a star tracker, a breadboard tracker system, is presented in tabular form. All data presented was normalized to the pixel dimension of 20 micrometers. Data from determination of maximum spatial noise as it applies to the coarse and fine acquisition modes is presented. Pointing accuracy test data, raw pixel data for the track cycle, and data from equipment related tests is also presented.

Material Handling Equipment Evaluation for Crater Repair

DTIC Science & Technology

2016-11-01

Department of the Army position unless so designated by other authorized documents. DESTROY THIS REPORT WHEN NO LONGER NEEDED. DO NOT RETURN IT TO THE...project. Jeb. S. Tingle was the ERDC Airfield Damage Repair program manager. The work was performed by the Airfields and Pavement Branch (GMA) of the...USAF’s) ability to perform airfield pavement repair tasks to support the operation of modern aircraft for a variety of mission scenarios. The ADR

Advanced On-the-Job Training System: System Specification

DTIC Science & Technology

1990-05-01

3.1.5.2.10 Evaluation Subsystem spotfor the Traking Devopment and Deliery Subsystem ..... 22 3.1.5.2.11 TrIning Development=dDelivery Subsystem sL...e. Alsys Ada compiler f. Ethernet Local Area Network reference manual(s) g. Infotron 992 network reference manual(s) h. Computer Program Source...1989 a. Daily check of mainframe components, including all elements critical to support the terminal network . b. Restoration of mainframe equipment

Proactive life extension of pressure vessels

NASA Astrophysics Data System (ADS)

Mager, Lloyd

1998-03-01

For a company to maintain its competitive edge in today's global market every opportunity to gain an advantage must be exploited. Many companies are strategically focusing on improved utilization of existing equipment as well as regulatory compliance. Abbott Laboratories is no exception. Pharmaceutical companies such as Abbott Laboratories realize that reliability and availability of their production equipment is critical to be successful and competitive. Abbott Laboratories, like many of our competitors, is working to improve safety, minimize downtime and maximize the productivity and efficiency of key production equipment such as the pressure vessels utilized in our processes. The correct strategy in obtaining these objectives is to perform meaningful inspection with prioritization based on hazard analysis and risk. The inspection data gathered in Abbott Laboratories pressure vessel program allows informed decisions leading to improved process control. The results of the program are reduced risks to the corporation and employees when operating pressure retaining equipment. Accurate and meaningful inspection methods become the cornerstone of a program allowing proper preventative maintenance actions to occur. Successful preventative/predictive maintenance programs must utilize meaningful nondestructive evaluation techniques and inspection methods. Nondestructive examination methods require accurate useful tools that allow rapid inspection for the entire pressure vessel. Results from the examination must allow the owner to prove compliance of all applicable regulatory laws and codes. At Abbott Laboratories the use of advanced NDE techniques, primarily B-scan ultrasonics, has provided us with the proper tools allowing us to obtain our objectives. Abbott Laboratories uses B-scan ultrasonics utilizing a pulse echo pitch catch technique to provide essential data on our pressure vessels. Equipment downtime is reduced because the nondestructive examination usually takes place while our vessels are in service. As the inspection takes place we are able to view a real time image of detected discontinuities on a video monitor. The B-scan ultrasonic technique is allowing us to perform fast accurate examinations covering up to 95% of the surface area of each pressure vessel. Receiving data on 95% of a pressure vessel provides us with a lot of useful information. We use this data to determine the condition of each pressure vessel. Once the condition is known the vessels are classed by risk. The risk level is then managed by making decisions related to repair, operating parameters, accepting and monitoring or replacement of the equipment. Inspection schedules are set at maximum intervals and reinspection is minimized for the vessels that are not at risk. The remaining life of each pressure vessel is determined, mechanical integrity is proven and regulatory requirements are met. Abbott Laboratories is taking this proactive approach because we understand that our process equipment is a critical element for successful operation. A run to failure practice would never allow Abbott Laboratories to achieve the corporation's objective of being the world's leading health care company. Nondestructive state of the art technology and the understanding of its capabilities and limitations are key components of a proactive program for life extension of pressure vessels. 26

The Impact of a Psychoeducational Prevention Program for Behaviorally At-Risk Students: EQUIP for Educators

ERIC Educational Resources Information Center

DiBiase, Ann-Marie

2010-01-01

This study examined the effectiveness of a multicomponent psychoeducational prevention program ("EQUIP for Educators") Two aspects were examined: (1) if there was a significant relationship among the three psychometric measures: Social Skills Rating System (SSRS), Children's Inventory of Anger (ChIA), Sociomoral Reflection and…

78 FR 7306 - Energy Efficiency Program for Commercial and Industrial Equipment: Public Meeting and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-01

... Efficiency Program for Commercial and Industrial Equipment: Public Meeting and Availability of the Framework Document for Commercial and Industrial Fans and Blowers AGENCY: Office of Energy Efficiency and Renewable... and industrial fans and blowers. To inform interested parties and to facilitate this process, DOE has...

78 FR 7304 - Energy Efficiency Program for Commercial and Industrial Equipment: Public Meeting and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-01

... Efficiency Program for Commercial and Industrial Equipment: Public Meeting and Availability of the Framework Document for Commercial and Industrial Pumps AGENCY: Office of Energy Efficiency and Renewable Energy... industrial pumps. To inform interested parties and to facilitate this process, DOE has prepared a Framework...

Heavy Construction Equipment Mechanic; A Suggested Guide for a Training Course.

ERIC Educational Resources Information Center

Division of Manpower Development and Training. , BAVT.

Prepared by a technical writer for the Division of Manpower Development and Training, this guide is intended to aid instructors, supervisors, and administrators of vocational education and manpower training programs in establishing training programs for mechanics and technicians entering the occupation of servicing heavy construction equipment.…

40 CFR 1027.101 - To whom do these requirements apply?

Code of Federal Regulations, 2011 CFR

2011-07-01

... POLLUTION CONTROLS FEES FOR ENGINE, VEHICLE, AND EQUIPMENT COMPLIANCE PROGRAMS § 1027.101 To whom do these..., vehicle, and equipment compliance program (EVECP). This includes activities related to approving... products: (1) Motor vehicles and motor vehicle engines we regulate under 40 CFR part 86. This includes...

76 FR 43941 - Energy Conservation Program: Energy Conservation Standards for Direct Heating Equipment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-22

... DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket Number EERE-2011-BT-STD-0047] RIN 1904-AC56 Energy Conservation Program: Energy Conservation Standards for Direct Heating Equipment AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION: Notice of proposed rulemaking and announcement...

78 FR 64295 - Energy Conservation Program: Test Procedure for Commercial Refrigeration Equipment

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-28

... amended under this section shall be reasonably designed to produce test results which measure energy... as members of the Working Group, in addition to two members from ASRAC, and one DOE representative... Energy Conservation Program: Test Procedure for Commercial Refrigeration Equipment; Proposed Rule #0;#0...

CALiPER Exploratory Study: Accounting for Uncertainty in Lumen Measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bergman, Rolf; Paget, Maria L.; Richman, Eric E.

2011-03-31

With a well-defined and shared understanding of uncertainty in lumen measurements, testing laboratories can better evaluate their processes, contributing to greater consistency and credibility of lighting testing a key component of the U.S. Department of Energy (DOE) Commercially Available LED Product Evaluation and Reporting (CALiPER) program. Reliable lighting testing is a crucial underlying factor contributing toward the success of many energy-efficient lighting efforts, such as the DOE GATEWAY demonstrations, Lighting Facts Label, ENERGY STAR® energy efficient lighting programs, and many others. Uncertainty in measurements is inherent to all testing methodologies, including photometric and other lighting-related testing. Uncertainty exists for allmore » equipment, processes, and systems of measurement in individual as well as combined ways. A major issue with testing and the resulting accuracy of the tests is the uncertainty of the complete process. Individual equipment uncertainties are typically identified, but their relative value in practice and their combined value with other equipment and processes in the same test are elusive concepts, particularly for complex types of testing such as photometry. The total combined uncertainty of a measurement result is important for repeatable and comparative measurements for light emitting diode (LED) products in comparison with other technologies as well as competing products. This study provides a detailed and step-by-step method for determining uncertainty in lumen measurements, working closely with related standards efforts and key industry experts. This report uses the structure proposed in the Guide to Uncertainty Measurements (GUM) for evaluating and expressing uncertainty in measurements. The steps of the procedure are described and a spreadsheet format adapted for integrating sphere and goniophotometric uncertainty measurements is provided for entering parameters, ordering the information, calculating intermediate values and, finally, obtaining expanded uncertainties. Using this basis and examining each step of the photometric measurement and calibration methods, mathematical uncertainty models are developed. Determination of estimated values of input variables is discussed. Guidance is provided for the evaluation of the standard uncertainties of each input estimate, covariances associated with input estimates and the calculation of the result measurements. With this basis, the combined uncertainty of the measurement results and finally, the expanded uncertainty can be determined.« less

Laser range pole field evaluation report

NASA Technical Reports Server (NTRS)

1973-01-01

A field evaluation was made of the laser pole equipment. The basic plan for the evaluation was to expose the equipment to the actual people and environment for which it was intended and determine, through the use of the equipment, its resultant effectivity in terms of improved performance. Results show the equipment performed better than expected in the high elevation clean air of Colorado, and did as well in Tennessee.

Implementation and Sustainability of the Russian Federation Ministry of Defense Nuclear Personnel Reliability Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

LataPhD, Vasiliy; Coates, Cameron W

2010-01-01

Through a cooperative effort between the US Department of Energy and the Russian Federation (RF) Ministry of Defense (MOD) a Personnel Reliability Program (PRP) for the nuclear handlers within the RF MOD is at the stage of implementation. Sustaining the program is of major significance for long term success. This paper will discuss the elements of the RF PRP and the equipment needs for implementation. Program requirements, documentation needs, training, and assurances of appropriate equipment use will be addressed.

10 CFR 600.321 - Real property and equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... following: (1) During the time that the real property or equipment is used on the project or program for... 10 Energy 4 2010-01-01 2010-01-01 false Real property and equipment. 600.321 Section 600.321....321 Real property and equipment. (a) Prior approvals for acquisition with Federal funds. Recipients...

Video. A Guide to the Use of Portable Video Equipment.

ERIC Educational Resources Information Center

Rowatt, Robert W.

This guide describes the portable equipment necessary for preparing a video production, and recommends ways of using that equipment to create a video program. Step by step instructions are provided for setting up the equipment for battery operation or with a mains electricity supply. Information is also given on procedures for recording, playing…

Outdoor Power Equipment Technician: Apprenticeship Course Outline. Apprenticeship and Industry Training. 5111.1

ERIC Educational Resources Information Center

Alberta Advanced Education and Technology, 2011

2011-01-01

The graduate of the Outdoor Power Equipment Technician apprenticeship program is a certified journeyperson who will be able to: (1) supervise, train and coach apprentices; (2) service, maintain, repair and rebuild outdoor power equipment and outdoor power equipment accessories; (3) communicate clearly with customers, staff, suppliers, as required;…

10 CFR 600.134 - Equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the following standards. Equipment with a current per-unit fair market value of less than $5000 may be... with a current per unit fair market value of $5000 or more, the recipient may retain the equipment for... the cost of the original project or program to the current fair market value of the equipment. If the...

A Scenario-Based Virtual Patient Program to Support Substance Misuse Education.

PubMed

Zlotos, Leon; Power, Ailsa; Hill, Duncan; Chapman, Paul

2016-04-25

Objective. To evaluate virtual patient (VP) programs for injecting equipment provision (IEP) and opiate substitution therapy (OST) services with respect to confidence and knowledge among preregistration pharmacist trainees. Methods. Preregistration trainee pharmacists pilot-tested the VP programs and were invited to complete pre/post and 6-month assessments of knowledge and perceived confidence. Results. One hundred six trainees participated and completed the pre/postassessments. Forty-six (43.4%) participants repeated the assessments at six months. Scores in perceived confidence increased in all domains at both time points postprogram. Knowledge scores were greater posteducation than preeducation. Knowledge scores were also greater six months after education than preeducation. Knowledge scores at six months were lower than posteducation for both programs. Conclusion. Virtual patients programs increased preregistration pharmacists' knowledge and confidence with regard to IEP and OST immediately after use and at six months postprogram. There was a loss of clinical knowledge over time but confidence change was sustained.

The influence of the perceived consequences of refusing to share injection equipment among injection drug users: Balancing competing risks

PubMed Central

Wagner, Karla D.; Lankenau, Stephen E.; Palinkas, Lawrence A.; Richardson, Jean L.; Chou, Chih-Ping; Unger, Jennifer B.

2011-01-01

Injection drug users (IDUs) are at risk for HIV and other bloodborne pathogens through receptive syringe sharing (RSS) and receptive paraphernalia sharing (RPS). Research into the influence of the perceived risk of HIV infection on injection risk behavior has yielded mixed findings. One explanation may be that consequences other than HIV infection are considered when IDUs are faced with decisions about whether or not to share equipment. We investigated the perceived consequences of refusing to share injection equipment among 187 IDUs recruited from a large syringe exchange program in Los Angeles, California, assessed their influence on RSS and RPS, and evaluated gender differences. Two sub-scales of perceived consequences were identified: structural/external consequences and social/internal consequences. In multiple linear regression, the perceived social/internal consequences of refusing to share were associated with both RSS and RPS, after controlling for other psychosocial constructs and demographic variables. Few statistically significant gender differences emerged. Assessing the consequences of refusing to share injection equipment may help explain persistent injection risk behavior, and may provide promising targets for comprehensive intervention efforts designed to address both individual and structural risk factors. PMID:21498004

A Study on Performance and Safety Tests of Electrosurgical Equipment

PubMed Central

Tavakoli Golpaygani, A.; Movahedi, M.M.; Reza, M.

2016-01-01

Introduction: Modern medicine employs a wide variety of instruments with different physiological effects and measurements. Periodic verifications are routinely used in legal metrology for industrial measuring instruments. The correct operation of electrosurgical generators is essential to ensure patient’s safety and management of the risks associated with the use of high and low frequency electrical currents on human body. Material and Methods: The metrological reliability of 20 electrosurgical equipment in six hospitals (3 private and 3 public) was evaluated in one of the provinces of Iran according to international and national standards. Results: The achieved results show that HF leakage current of ground-referenced generators are more than isolated generators and the power analysis of only eight units delivered acceptable output values and the precision in the output power measurements was low. Conclusion: Results indicate a need for new and severe regulations on periodic performance verifications and medical equipment quality control program especially in high risk instruments. It is also necessary to provide training courses for operating staff in the field of meterology in medicine to be acquianted with critical parameters to get accuracy results with operation room equipment. PMID:27853725

How to estimate the cost of point-of-care CD4 testing in program settings: an example using the Alere Pima Analyzer in South Africa.

PubMed

Larson, Bruce; Schnippel, Kathryn; Ndibongo, Buyiswa; Long, Lawrence; Fox, Matthew P; Rosen, Sydney

2012-01-01

Integrating POC CD4 testing technologies into HIV counseling and testing (HCT) programs may improve post-HIV testing linkage to care and treatment. As evaluations of these technologies in program settings continue, estimates of the costs of POC CD4 tests to the service provider will be needed and estimates have begun to be reported. Without a consistent and transparent methodology, estimates of the cost per CD4 test using POC technologies are likely to be difficult to compare and may lead to erroneous conclusions about costs and cost-effectiveness. This paper provides a step-by-step approach for estimating the cost per CD4 test from a provider's perspective. As an example, the approach is applied to one specific POC technology, the Pima Analyzer. The costing approach is illustrated with data from a mobile HCT program in Gauteng Province of South Africa. For this program, the cost per test in 2010 was estimated at $23.76 (material costs  = $8.70; labor cost per test  = $7.33; and equipment, insurance, and daily quality control  = $7.72). Labor and equipment costs can vary widely depending on how the program operates and the number of CD4 tests completed over time. Additional costs not included in the above analysis, for on-going training, supervision, and quality control, are likely to increase further the cost per test. The main contribution of this paper is to outline a methodology for estimating the costs of incorporating POC CD4 testing technologies into an HCT program. The details of the program setting matter significantly for the cost estimate, so that such details should be clearly documented to improve the consistency, transparency, and comparability of cost estimates.

Rail Transit System Maintenance Practices for Automatic Fare Collection Equipment

DOT National Transportation Integrated Search

1984-05-01

A review of rail transit system maintenance practices for automatic fare collection (AFC) equipment was performed. This study supports an UMTA sponsored program to improve the reliability of AFC equipment. The maintenance practices of the transit sys...

Paranoia.Ada: A diagnostic program to evaluate Ada floating-point arithmetic

NASA Technical Reports Server (NTRS)

Hjermstad, Chris

1986-01-01

Many essential software functions in the mission critical computer resource application domain depend on floating point arithmetic. Numerically intensive functions associated with the Space Station project, such as emphemeris generation or the implementation of Kalman filters, are likely to employ the floating point facilities of Ada. Paranoia.Ada appears to be a valuabe program to insure that Ada environments and their underlying hardware exhibit the precision and correctness required to satisfy mission computational requirements. As a diagnostic tool, Paranoia.Ada reveals many essential characteristics of an Ada floating point implementation. Equipped with such knowledge, programmers need not tremble before the complex task of floating point computation.

Engineering and simulation of life science Spacelab experiments

NASA Technical Reports Server (NTRS)

Bush, B.; Rummel, J.; Johnston, R. S.

1977-01-01

Approaches to the planning and realization of Spacelab life sciences experiments, which may involve as many as 16 Space Shuttle missions and 100 tests, are discussed. In particular, a Spacelab simulation program, designed to evaluate problems associated with the use of live animal specimens, the constraints imposed by zero gravity on equipment operation, training of investigators and data management, is described. The simulated facility approximates the hardware and support systems of a current European Space Agency Spacelab model. Preparations necessary for the experimental program, such as crew activity plans, payload documentation and inflight experimental procedures are developed; health problems of the crew, including human/animal microbial contamination, are also assessed.

Effectiveness evaluation of STOL transport operations

NASA Technical Reports Server (NTRS)

Hitt, E. F.; Bruckner, J. M. H.; Drago, V. J.; Brown, R. A.; Rea, F. G.; Porter, R. F.

1973-01-01

A short-takeoff and landing (STOL) systems simulation model has been developed and implemented in a computer code (known as STOL OPS) which permits evaluation of the operation of a STOL aircraft and its avionics in a commercial airline operating environment. STOL OPS concentrated on the avionics functions of navigation, guidance, control, communication, hazard aviodance, and systems management. External world factors influencing the operation of the STOL aircraft include each airport and its geometry, air traffic at each airport, air traffic control equipment and procedures, weather (including winds and visibility), and the flight path between each airport served by the route. The development of the STOL OPS program provides NASA a set of computer programs which can be used for detailed analysis of a STOL aircraft and its avionics and permit establishment of system requirements as a function of airline mission performance goals.

Does team training work? Principles for health care.

PubMed

Salas, Eduardo; DiazGranados, Deborah; Weaver, Sallie J; King, Heidi

2008-11-01

Teamwork is integral to a working environment conducive to patient safety and care. Team training is one methodology designed to equip team members with the competencies necessary for optimizing teamwork. There is evidence of team training's effectiveness in highly complex and dynamic work environments, such as aviation and health care. However, most quantitative evaluations of training do not offer any insight into the actual reasons why, how, and when team training is effective. To address this gap in understanding, and to provide guidance for members of the health care community interested in implementing team training programs, this article presents both quantitative results and a specific qualitative review and content analysis of team training implemented in health care. Based on this review, we offer eight evidence-based principles for effective planning, implementation, and evaluation of team training programs specific to health care.

[Hygienic evaluation of the efficacy of the regional program of the modernization of school meals (on the example of Altai Krai)].

PubMed

Saldan, I P; Filippova, S P; Turchaninov, D V; Okolelova, O V; Vilms, E A

2014-01-01

With the use of the method for the analysis of the frequency of food intake there was studied the actual nutrition in adolescents at the age of 12-17 years (n = 257) who were the students of the urban and rural educational institutions (EI) of Altai Krai. The analysis of the menu-layout and assessment of nutritional status was performed with the use of clinical methods. The main group consisted of 125 adolescents from the EI with upgraded technological equipment of the nutrition unit, the comparison group--132 teenagers from EI with non-upgraded equipment of the nutrition department. The program of the modernization of school meals was implemented in several ways and included the reconstruction and technical re-equipment of school nutrition units on the base of modern technologies, delivery and introduction in accordance with the requirements of the school menu, differentiated by age groups with the use of food products aimed at the prevention of diseases caused by micronutrient deficiency. This led to the enlargement of the assortment of dishes, the increase of the coverage for catering students, improvement of the structure of student nutrition, the increased in the intake of a number of nutrients. Symptoms of skin lesions associated with insufficient provision of micronutrients in a core group of students occurred less common than in the comparison group (p < 0.01).

Fire toxicology program. JSC methodology

NASA Technical Reports Server (NTRS)

Schneider, H.; Bafus, D.

1978-01-01

Toxicological testing of spacecraft materials was initiated in 1965. Toxicological evaluations of the pyrolysis/combustion products of candidate spacecraft materials were performed using a modified 142 liter Bethlehem Chamber equipped with a Linberg Model 55031 furnace external to the chamber. In all of the assessments, lethality was chosen as the endpoint. A new pyrolysis/combustion chamber was developed for toxicological testing and ranking of both spacecraft and aircraft materials. The pyrolysis/combustion chamber permits the use of both behavior and physiological measurements as indicators of incapacitation. Methods were developed which employ high resolution gas chromatography/mass spectrometry to generate chamber atmospheric profiles which indicate the reproductibility of pyrolysate concentrations. The atmospheric volatile profiles in combination with CO, CO2, and O2 analysis indicates that small chamber equipped with an internal furnace will give reproducible results.

Mondelēz Hope Kitchen Program, China: a Program Impact Pathways (PIP) analysis.

PubMed

Li, Yanran; Yao, Xiaoxun; Gu, Lan

2014-09-01

Mondelēz Hope Kitchen is a community program initiated jointly in 2009 by Mondelēz International and the China Youth Development Foundation (CYDF). In response to the urgent needs of students, parents, and teachers at primary and middle schools in poverty-stricken rural areas of China, the program addresses the complex and intertwined issues of undernutrition and obesity. By funding both kitchen equipment and teacher training in health and nutrition, the Mondelēz Hope Kitchen Program improves the capacity of schools to supply healthy meals, helping students to access safe and nutritious foods and, ultimately, to improve their nutritional status and health. In 2011, the Mondelēz International Foundation awarded CYDF a grant to formally assess the impact of the original program design. The Mondelēz International Foundation encouraged CYDF and six other healthy lifestyles-focused community partners around the world to participate in this program evaluation workshop. The goals of this study were to describe the logic model of the Mondelēz Hope Kitchen Program, summarize a recent evaluation of the Mondelēz Hope Kitchen Program, and conduct a Program Impact Pathways (PIP) analysis to identify Critical Quality Control Points (CCPs) and a suite of impact indicators. The findings were presented at the Healthy Lifestyles Program Evaluation Workshop held in Granada, Spain, 13-14 September 2013, under the auspices of the Mondelēz International Foundation. The authors developed the program's PIP diagram based on deliberations involving the program managers and Director and consulting the "Hope Kitchen Management Rules "and "Hope Kitchen Inspection and Acceptance Report". The PIP analyses identified three CCPs: buy-in from schools, kitchen infrastructure, and changes in teachers' knowledge of nutrition after training. In addition, changes in children's knowledge of nutrition will be added to the core suite of impact evaluation indicators that also includes children's dietary behaviors. Participation in this program evaluation workshop provided the Mondelēz Hope Kitchen team with the tools to improve the program using a sound monitoring system.

Qualitative process evaluation of an Australian alcohol media literacy study: recommendations for designing culturally responsive school-based programs.

PubMed

Gordon, Chloe S; Kervin, Lisa K; Jones, Sandra C; Howard, Steven J

2017-02-02

Alcohol media literacy programs seek to mitigate the potentially harmful effects of alcohol advertising on children's drinking intentions and behaviours through equipping them with skills to challenge media messages. In order for such programs to be effective, the teaching and learning experiences must be tailored to their specific cultural context. Media in the Spotlight is an alcohol media literacy program aimed at 9 to 12 year old Australian children. This study evaluates the process and implementation of the program, outlining the factors that facilitated and inhibited implementation. From this evaluation, a pedagogical framework has been developed for health professionals implementing culturally responsive programs in school settings. Process measures included: semi-structured interviews with teachers before and after the program was implemented (n = 11 interviews), program evaluation questionnaires completed by children (n = 166), lesson observations completed by teachers (n = 35 observations), and reflective journal entries completed by the researcher (n = 44 entries). A thematic analysis approach was used to analyse all of the data sets using NVivo. Inductive coding was used, whereby the findings were derived from the research objectives and multiple readings and interpretations of the data. Five key pedagogical considerations were identified that facilitated implementation. These were: connecting to the students' life worlds to achieve cultural significance; empowering students with real-world skills to ensure relevance; ensuring programs are well structured with strong connections to the school curriculum; creating developmentally appropriate activities while providing a range of assessment opportunities; and including hands-on and interactive activities to promote student engagement. Three potential inhibitors to implementing the alcohol media literacy program in upper-elementary school classrooms were identified. These included topic sensitivities, classroom management challenges, and fitting new programs into already busy school schedules. Overall, the program content and individual lessons were well received by the teachers and students. The lessons learned from the development, implementation and evaluation of this program can provide health professionals with key pedagogical strategies for designing culturally responsive educational programs. Culturally responsive programs are critical for ensuring interventions are effective for their specific context.

Engineer Equipment Mechanic.

ERIC Educational Resources Information Center

Marine Corps Inst., Washington, DC.

Developed as part of the Marine Corps Institute (MCI) correspondence training program, this course on engineer equipment mechanics is designed to advance the professional competence of privates through sergeants as equipment mechanics, Military Occupation Specialty 1341, and is adaptable for nonmilitary instruction. Introductory materials include…

An overview of passenger equipment fullscale impact tests : results to date

DOT National Transportation Integrated Search

2001-11-25

As part of the Federal Railroad Administrations Equipment Safety Research Program, a series of full-scale impact tests are being conducted on rail passenger vehicles. Three tests are intended to define the performance of current-design equipment i...

The effects of school physical education grants on obesity, fitness, and academic achievement.

PubMed

von Hippel, Paul T; Bradbury, W Kyle

2015-09-01

Foundations and governments fund a number of programs that provide grants to improve school physical education or other forms of school-based physical activity. The effects of these grant programs are unknown. We evaluate the effects of Texas Fitness Now, a program in which the state of Texas granted $37 million to improve physical education in high-poverty middle schools over the 4 school years from 2007-08 to 2010-11. The stated goals of Texas Fitness Now were to reduce obesity, increase fitness, and raise academic achievement. We summarize how Texas Fitness Now funds were spent and estimate the impact of Texas Fitness Now using a fixed-effects longitudinal model that exploits changes in schools' eligibility over time. Changes in eligibility occurred when eligibility expanded to new schools after year 2 and when the program was terminated after year 4. Most Texas Fitness Now funds were spent on sports and fitness equipment. Smaller amounts were spent on anti-obesity curricula. Texas Fitness Now improved strength and flexibility, especially among girls, but it did not improve BMI or academic achievement, and it had mixed effects on aerobic capacity. The fitness benefits were not lost in the year after the program ended, perhaps because schools kept the equipment that they had bought during their years of eligibility. The results of Texas Fitness Now were typical for an intervention that relied almost exclusively on physical activity. Programs that improve BMI as well as fitness tend to have a more fully developed nutrition component. Copyright © 2015 Elsevier Inc. All rights reserved.

76 FR 34914 - Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-15

... Commercial and Industrial Equipment: Proposed Determination of Set-Top Boxes and Network Equipment as a... that set-top boxes and network equipment qualify as a covered product under Part A of Title III of the Energy Policy and Conservation Act (EPCA), as amended. DOE has determined that set-top boxes and network...

34 CFR 75.618 - Charges for use of equipment or supplies.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 34 Education 1 2014-07-01 2014-07-01 false Charges for use of equipment or supplies. 75.618 Section 75.618 Education Office of the Secretary, Department of Education DIRECT GRANT PROGRAMS What Conditions Must Be Met by a Grantee? Equipment and Supplies § 75.618 Charges for use of equipment or supplies...

Shuttle orbiter S-band communications equipment design evaluation

NASA Technical Reports Server (NTRS)

Springett, J. C.

1979-01-01

An assessment of S-band communication equipment includes: (1) the review and analysis of the ability of the various subsystem avionic equipment designs to interface with, and operate on signals from/to adjoining equipment; (2) the performance peculiarities of the hardware against the overall specified system requirements; and (3) the evaluation of EMC EMI test results of the various equipment with respect to the possibility of mutual interferences.

47 CFR 76.953 - Limitation on filing a complaint.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Limitation on filing a complaint. 76.953... programming service or associated equipment may be filed against a cable operator only in the event of a rate... change for cable programming service or associated equipment may be filed against a cable operator only...

ENVIRONMENTAL TECHNOLOGY VERIFICATION COATINGS AND COATING EQUIPMENT PROGRAM (ETV CCEP), FINAL TECHNOLOGY APPLICATIONS GROUP TAGNITE--TESTING AND QUALITY ASSURANCE PLAN (T/QAP)

EPA Science Inventory

The overall objective of the Environmental Testing and Verification Coatings and Coating Equipment Program is to verify pollution prevention and performance characteristics of coating technologies and make the results of the testing available to prospective coating technology use...

77 FR 4698 - Energy Conservation Program: Test Procedure and Energy Conservation Standard for Set-Top Boxes...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-31

... Conservation Program: Test Procedure and Energy Conservation Standard for Set-Top Boxes and Network Equipment... comments on the request for information pertaining to the development of test procedures and energy conservation standards for set-top boxes and network equipment. The comment period is extended to March 15...

Programs for Infants and Young Children. Part IV: Facilities and Equipment.

ERIC Educational Resources Information Center

Sale, June

This manual is designed to facilitate planning for day care center facilities. Goals and principles of day care are discussed in relation to programs for infants, toddlers, and preschoolers with special attention to staff, parents, and community. Suggestions are presented for indoor and outdoor planning for such topics as equipment, supplies,…

Cost estimation and analysis using the Sherpa Automated Mine Cost Engineering System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stebbins, P.E.

1993-09-01

The Sherpa Automated Mine Cost Engineering System is a menu-driven software package designed to estimate capital and operating costs for proposed surface mining operations. The program is engineering (as opposed to statistically) based, meaning that all equipment, manpower, and supply requirements are determined from deposit geology, project design and mine production information using standard engineering techniques. These requirements are used in conjunction with equipment, supply, and labor cost databases internal to the program to estimate all associated costs. Because virtually all on-site cost parameters are interrelated within the program, Sherpa provides an efficient means of examining the impact of changesmore » in the equipment mix on total capital and operating costs. If any aspect of the operation is changed, Sherpa immediately adjusts all related aspects as necessary. For instance, if the user wishes to examine the cost ramifications of selecting larger trucks, the program not only considers truck purchase and operation costs, it also automatically and immediately adjusts excavator requirements, operator and mechanic needs, repair facility size, haul road construction and maintenance costs, and ancillary equipment specifications.« less

Flight test evaluation of the Stanford University/United Airlines differential GPS Category 3 automatic landing system

NASA Technical Reports Server (NTRS)

Kaufmann, David N.; Ncnally, B. David

1995-01-01

Test flights were conducted to evaluate the capability of Differential Global Positioning System (DGPS) to provide the accuracy and integrity required for International Civil Aviation Organization (ICAO) Category (CAT) 3 precision approach and landings. These test flights were part of a Federal Aviation Administration (FAA) program to evaluate the technical feasibility of using DGPS based technology for CAT 3 precision approach and landing applications. A United Airlines Boeing 737-300 (N304UA) was equipped with DGPS receiving equipment and additional computing capability provided by Stanford University. The test flights were conducted at NASA Ames Research Center's Crows Landing Flight Facility, Crows Landing, California. The flight test evaluation was based on completing 100 approaches and autolandings; 90 touch and go, and 10 terminating with a full stop. Two types of accuracy requirements were evaluated: 1) Total system error, based on the Required Navigation Performance (RNP), and 2) Navigation sensor error, based on ICAO requirements for the Microwave Landing System (MLS). All of the approaches and autolandings were evaluated against ground truth reference data provided by a laser tracker. Analysis of these approaches and autolandings shows that the Stanford University/United Airlines system met the requirements for a successful approach and autolanding 98 out of 100 approaches and autolandings, based on the total system error requirements as specified in the FAA CAT 3 Level 2 Flight Test Plan.

Mobile detection assessment and response systems (MDARS): a force protection physical security operational success

NASA Astrophysics Data System (ADS)

Shoop, Brian; Johnston, Michael; Goehring, Richard; Moneyhun, Jon; Skibba, Brian

2006-05-01

MDARS is a Semi-autonomous unmanned ground vehicle with intrusion detection & assessment, product & barrier assessment payloads. Its functions include surveillance, security, early warning, incident first response and product and barrier status primarily focused on a depot/munitions security mission at structured/semi-structured facilities. MDARS is in Systems Development and Demonstration (SDD) under the Product Manager for Force Protection Systems (PM-FPS). MDARS capabilities include semi-autonomous navigation, obstacle avoidance, motion detection, day and night imagers, radio frequency tag inventory/barrier assessment and audio challenge and response. Four SDD MDARS Patrol Vehicles have been undergoing operational evaluation at Hawthorne Army Depot, NV (HWAD) since October 2004. Hawthorne personnel were trained to administer, operate and maintain the system in accordance with the US Army Military Police School (USAMPS) Concept of Employment and the PM-FPS MDARS Integrated Logistic Support Plan. The system was subjected to intensive periods of evaluation under the guidance and control of the Army Test and Evaluation Center (ATEC) and PM-FPS. Significantly, in terms of User acceptance, the system has been under the "operational control" of the installation performing security and force protection missions in support of daily operations. This evaluation is intended to assess MDARS operational effectiveness in an operational environment. Initial observations show that MDARS provides enhanced force protection, can potentially reduce manpower requirements by conducting routine tasks within its design capabilities and reduces Soldier exposure in the initial response to emerging incidents and situations. Success of the MDARS program has been instrumental in the design and development of two additional robotic force protection programs. The first was the USAF Force Protection Battle Lab sponsored Remote Detection Challenge & Response (REDCAR) concept demonstration executed by the Air Force Robotics Lab (AFRL). The REDCAR used an MDARS PUV as the central robotic technology and expanded the concept to incorporate a smaller high speed platform (SCOUT) equipped with lethal, non-lethal and challenge components as an engagement platform and, in a marsupial configuration on the MDARS, a small UGV that can be deployed to investigate close quarters areas. The Family of Integrated Rapid Response Equipment (FIRRE) program further expands these concepts by incorporating and adapting other mobile/tactical force protection equipment with a more robust Unmanned Ground Vehicle into an "Expeditionary" configuration to provide the current force with a rapidly deployable force protection system that can operate in austere less structured and protected environments. A USAMPS/ MANCEN sponsored "FIRRE System Demonstration" in Iraq is scheduled to begin in FY '07.

Performance and economic evaluation of the seahorse natural gas hot water heater conversion at Fort Stewart. Interim report, 1994 Summer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winiarski, D.W.

1995-01-01

The federal government is the largest single energy consumer in the United States cost valued at nearly $10 billion annually. The US Department of Energy`s (DOE) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the federal sector. One such effort, the New Technology Demonstration Program (NTDP), seeks to evaluate new energy-saving US technologies and secure their more timely adoption by the US government. Pacific Northwest Laboratory (PNL) is one of four DOE laboratories that participate in the New Technologies Demonstration Program, providing technical expertise and equipment to evaluate new, energy-saving technologies being studiedmore » under that program. This interim report provides the results of a field evaluation that PNL conducted for DOE/FEMP and the US Department of Defense (DoD) Strategic Environmental Research and Development Program (SERDP) to examine the performance of a candidate energy-saving technology-a hot water heater conversion system to convert electrically heated hot water tanks to natural gas fuel. The unit was installed at a single residence at Fort Stewart, a US Army base in Georgia, and the performance was monitored under the NTDP. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) were Gas Fired Products, developers of the technology; the Public Service Company of North Carolina; Atlanta Gas Light Company; the Army Corps of Engineers; Fort Stewart; and Pacific Northwest Laboratory.« less

International Environmental Evaluation for the Helical Screw Expander Generator Unit Projects in Cesano, Italy and Broadlands, New Zealand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webb, J.W.; Mezga, L.J.; Reed, A.W.

1981-08-01

The objectives of the Helical Screw Expander (HSE) Generator Program are (1) to accelerate the development of geothermal resources by introducing this advanced conversion technology, (2) to provide operating experience to prospective users of the equipment, and (3) to collect data on the performance and reliability of the equipment under various geothermal resource conditions. The participants hope to achieve these goals by testing a small-scale, transportable HSE generator at existing geothermal test facilities that produce fluids of different salinity, temperature and pressure conditions. This Environmental Evaluation has been prepared, using available information, to analyze the environmental consequences of testing themore » HSE generator. Its purpose is to support a decision on the need for a complete environmental review of the HSE program under the terms of Executive Order 121 14, ''Environmental Effects Abroad of Major federal Actions''. This Executive Order requires review of projects which involve the release of potentially toxic effluents that are strictly regulated in the United States, or which may have significant environmental effects on the global commons, on natural or ecological resources of international significance, or on the environment of non-participating countries. The final guidelines implementing the provisions of the Executive Order for DOE have been published. This evaluation deals with testing to be conducted at Cesano, Italy by the designated contractor of the Italian government, the Ente Narionale per l'Energia Ellectrica (ENEL), and at Broadlands, New Zealand by the Ministry of Works and Development of New Zealand. Testing at Cerro Prieto, Mexico has already been completed by the Comision Federal de Electricidad and is not evaluated in this report.« less

40 CFR 1068.210 - What are the provisions for exempting test engines/equipment?

Code of Federal Regulations, 2010 CFR

2010-07-01

... exempt engines/equipment that you will use for research, investigations, studies, demonstrations, or... test engines/equipment? 1068.210 Section 1068.210 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR ENGINE PROGRAMS Exemptions...

40 CFR 1068.210 - What are the provisions for exempting test engines/equipment?

Code of Federal Regulations, 2011 CFR

2011-07-01

... exempt engines/equipment that you will use for research, investigations, studies, demonstrations, or... test engines/equipment? 1068.210 Section 1068.210 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR ENGINE PROGRAMS Exemptions...

42 CFR 433.35 - Equipment-Federal financial participation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 CFR part 95. Requirements concerning the management and disposition of equipment under the... 42 Public Health 4 2011-10-01 2011-10-01 false Equipment-Federal financial participation. 433.35... SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS STATE FISCAL ADMINISTRATION Federal Matching and General...

42 CFR 433.35 - Equipment-Federal financial participation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 CFR part 95. Requirements concerning the management and disposition of equipment under the... 42 Public Health 4 2010-10-01 2010-10-01 false Equipment-Federal financial participation. 433.35... SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS STATE FISCAL ADMINISTRATION Federal Matching and General...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

40 CFR 61.181 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... cooled, condensed, and removed in a solid form. Control device means the air pollution control equipment... failure of air pollution control equipment or process equipment or of a process to operate in a normal or... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL...

[Microbiological assessment of the Gouda-type cheese-making process in a Venezuelan industry].

PubMed

Dáivila, Jacqueline; Reyes, Genara; Corzo, Otoniel

2006-03-01

The adoption of the Hazard Analysis and Critical Control Point (HACCP) system is necessary to assure the safety of the product in the cheese-making industry. The compliment of pre-requisite programs as Good Manufacture Practices (GMPs) and Sanitation Standard Operating Procedures (SSOPs) are required before the implementation of the HACCP plan. GMPs are the standards related to equipments, tools, personnel, etc. SSOPs are the procedures related to hygiene and sanitation of the plant and workers. The aim of this study was to assess the compliment of the pre-requisite programs and the microbiological conditions of the Gouda type cheese-making process in a Venezuelan processing plant before designing a HACCP plan. Samples were: (a) raw milk, pasteurized milk, curd and ripened cheese, (b) water, (c) environment of the production areas and ripening premises, (d) equipments before and after sanitation, (e) food handlers. Microbiological analyses were done according to COVENIN standards. This study showed that even though pasteurization process was effective to kill pathogen bacteria of the raw milk and the water was safe, however there are deficient manufacture practices in the hygiene as well as in sanitation of the plant and food handlers. Prerequisite programs (GMP-SSOP) of this industry need to be well established, controlled and evaluated.

A Mathematical Model of the Inertial Properties of a Carrier-Backpack System. Volume IV

DTIC Science & Technology

1982-05-01

B.S., and Richard C. Nelson, Ph.D. 9. PERFORMING OR3ANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT, PROJECT, TASK BIomechanics Labo-atory AREA 6 WORK...Recommendations for rarther Study 30 Cited References 31 Appendices A. Clothing and Equipment Used in This Study 33 B. IMSL Policy Statement 49 C. The Biomechanica... biomechanics , researchers use a variety of research techn iques to evaluate various aspects of physical performance. Mathematical modeling is one

An evaluation of strategies to control noise from air conditioning and refrigeration condensing units

NASA Astrophysics Data System (ADS)

Durden, G. L.; Myers, J. O.; Towers, T. A.; Dickman, D. M.

1981-12-01

Noise from air conditioning and refrigeration condensing units is investigated. The practical aspects of attempting to implement innovative approaches are emphasized. These included: (1) sample selection, (2) noise measurement survey, (3) implementation of aggressive abatement procedures, (4) development and use of a screening graph for determining acceptability of sound rated outdoor unitary equipment, (5) incorporation of noise control considerations, (6) exploration of an operatinal curfew, and (7) development of an incentive/information program.

A leadership development program for surgeons: First-year participant evaluation.

PubMed

Pradarelli, Jason C; Jaffe, Gregory A; Lemak, Christy Harris; Mulholland, Michael W; Dimick, Justin B

2016-08-01

In a dynamic health care system, strong leadership has never been more important for surgeons. Little is known about how to design and conduct effectively a leadership program specifically for surgeons. We sought to evaluate critically a Leadership Development Program for practicing surgeons by exploring how the program's strengths and weaknesses affected the surgeons' development as physician-leaders. At a large academic institution, we conducted semistructured interviews with 21 surgical faculty members who applied voluntarily, were selected, and completed a newly created Leadership Development Program in December 2012. Interview transcripts underwent qualitative descriptive analysis with thematic coding based on grounded theory. Themes were extracted regarding surgeons' evaluations of the program on their development as physician-leaders. After completing the program, surgeons reported personal improvements in the following 4 areas: self-empowerment to lead, self-awareness, team-building skills, and knowledge in business and leadership. Surgeons felt "more confident about stepping up as a leader" and more aware of "how others view me and my interactions." They described a stronger grasp on "giving feedback" as well as a better understanding of "business/organizational issues." Overall, surgeon-participants reported positive impacts of the program on their day-to-day work activities and general career perspective as well as on their long-term career development plans. Surgeons also recommended areas where the program could potentially be improved. These interviews detailed self-reported improvements in leadership knowledge and capabilities for practicing surgeons who completed a Leadership Development Program. A curriculum designed specifically for surgeons may enable future programs to equip surgeons better for important leadership roles in a complex health care environment. Copyright © 2016 Elsevier Inc. All rights reserved.

A Leadership Development Program for Surgeons: First-Year Participant Evaluation

PubMed Central

Pradarelli, Jason C.; Jaffe, Gregory A.; Lemak, Christy Harris; Mulholland, Michael W.; Dimick, Justin B.

2016-01-01

Structured Abstract Background In a dynamic healthcare system, strong leadership has never been more important for surgeons. Little is known about how to effectively design and conduct a leadership program specifically for surgeons. We sought to critically evaluate a Leadership Development Program for practicing surgeons by exploring the strengths and weaknesses of program components on surgeons’ development as physician-leaders. Methods At a large academic institution, we conducted semi-structured interviews with 21 surgical faculty members who voluntarily applied, were selected, and completed a newly-created Leadership Development Program in December 2012. Interview transcripts underwent qualitative descriptive analysis with thematic coding based on grounded theory. Themes were extracted regarding surgeons’ evaluations of the program on their development as physician-leaders. Results After completing the program, surgeons reported personal improvements in the following 4 areas: self-empowerment to lead, self-awareness, team-building skills, and business and leadership knowledge. Surgeons felt “more confident about stepping up as a leader” and more aware about “how others view me and my interactions.” They described a stronger grasp on “giving feedback” as well as “business/organizational issues.” Overall, surgeon participants reported positive impacts of the program on their day-to-day work activities, general career perspective, as well as their long-term career development plans. Surgeons also recommended areas for potential improvement for the program. Conclusions These interviews detailed self-reported improvements in leadership knowledge and capabilities for practicing surgeons who completed a Leadership Development Program. A curriculum designed specifically for surgeons may enable future programs to better equip surgeons for important leadership roles in a complex healthcare environment. PMID:27138180

The test facility for the short prototypes of the LHC superconducting magnets

NASA Astrophysics Data System (ADS)

Delsolaro, W. Venturini; Arn, A.; Bottura, L.; Giloux, C.; Mompo, R.; Siemko, A.; Walckiers, L.

2002-05-01

The LHC development program relies on cryogenic tests of prototype and model magnets. This vigorous program is pursued in a dedicated test facility based on several vertical cryostats working at superfluid helium temperatures. The performance of the facility is detailed. Goals and test equipment for currently performed studies are reviewed: quench analysis and magnet protection studies, measurement of the field quality, test of ancillary electrical equipment like diodes and busbars. The paper covers the equipment available for tests of prototypes and some special series of LHC magnets to come.

A CONTROLLED EVALUATION OF A HIGH SCHOOL BIOMEDICAL PIPELINE PROGRAM: DESIGN AND METHODS

PubMed Central

Winkleby, Marilyn A.; Ned, Judith; Ahn, David; Koehler, Alana; Fagliano, Kathleen; Crump, Casey

2013-01-01

Given limited funding for school-based science education, non-school-based programs have been developed at colleges and universities to increase the number of students entering science- and health-related careers and address critical workforce needs. However, few evaluations of such programs have been conducted. We report the design and methods of a controlled trial to evaluate the Stanford Medical Youth Science Program’s Summer Residential Program (SRP), a 25-year-old university-based biomedical pipeline program. This 5-year matched cohort study uses an annual survey to assess educational and career outcomes among four cohorts of students who participate in the SRP and a matched comparison group of applicants who were not chosen to participate in the SRP. Matching on sociodemographic and academic background allows control for potential confounding. This design enables the testing of whether the SRP has an independent effect on educational- and career-related outcomes above and beyond the effects of other factors such as gender, ethnicity, socioeconomic background, and pre-intervention academic preparation. The results will help determine which curriculum components contribute most to successful outcomes and which students benefit most. After 4 years of follow-up, the results demonstrate high response rates from SRP participants and the comparison group with completion rates near 90%, similar response rates by gender and ethnicity, and little attrition with each additional year of follow-up. This design and methods can potentially be replicated to evaluate and improve other biomedical pipeline programs, which are increasingly important for equipping more students for science- and health-related careers. PMID:24563603

Performance Evaluation of Bucket based Excavating, Loading and Transport (BELT) Equipment - An OEE Approach

NASA Astrophysics Data System (ADS)

Mohammadi, Mousa; Rai, Piyush; Gupta, Suprakash

2017-03-01

Overall Equipment Effectiveness (OEE) has been used since last over two decades as a measure of performance in manufacturing industries. Unfortunately, enough, application of OEE in mining and excavation industry has not been duly adopted. In this paper an effort has been made to identify the OEE for performance evaluation of Bucket based Excavating, Loading and Transport (BELT) equipment. The conceptual model of OEE, as used in the manufacturing industries, has been revised to adapt to the BELT equipment. The revised and adapted model considered the operational time, speed and bucket capacity utilization losses as the key OEE components for evaluating the performance of BELT equipment. To illustrate the efficacy of the devised model on real-time basis, a case study was undertaken on the biggest single bucket excavating equipment - the dragline, in a large surface coal mine. One-year data was collected in order to evaluate the proposed OEE model.

Field monitoring and evaluation of a residential gas-engine-driven heat pump: Volume 2, Heating season

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, J.D.

1995-11-01

The Federal Government is the largest single energy consumer in the United States; consumption approaches 1.5 quads/year of energy (1 quad = 10{sup 15} Btu) at a cost valued at nearly $10 billion annually. The US Department of Energy (DOE) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the Federal sector. One such effort, the New Technology Demonstration Program (NTDP), seeks to evaluate new energy-saving US technologies and secure their more timely adoption by the US Government. Pacific Northwest Laboratory (PNL) is one of four DOE national multiprogram laboratories that participate in themore » NTDP by providing technical expertise and equipment to evaluate new, energy-saving technologies being studied and evaluated under that program. This two-volume report describes a field evaluation that PNL conducted for DOE/FEMP and the US Department of Defense (DoD) Strategic Environmental Research and Development Program (SERDP) to examine the performance of a candidate energy-saving technology -- a gas-engine-driven heat pump. The unit was installed at a single residence at Fort Sam Houston, a US Army base in San Antonio, Texas, and the performance was monitored under the NTDP. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) were York International, the heat pump manufacturer; Gas Research Institute (GRI), the technology developer; City Public Service of San Antonio, the local utility; American Gas Cooling Center (AGCC); Fort Sam Houston; and PNL.« less

Technical assessment of Mir-1 life support hardware for the international space station

NASA Technical Reports Server (NTRS)

Mitchell, K. L.; Bagdigian, R. M.; Carrasquillo, R. L.; Carter, D. L.; Franks, G. D.; Holder, D. W., Jr.; Hutchens, C. F.; Ogle, K. Y.; Perry, J. L.; Ray, C. D.

1994-01-01

NASA has been progressively learning the design and performance of the Russian life support systems utilized in their Mir space station. In 1992, a plan was implemented to assess the benefits of the Mir-1 life support systems to the Freedom program. Three primary tasks focused on: evaluating the operational Mir-1 support technologies and understanding if specific Russian systems could be directly utilized on the American space station and if Russian technology design information could prove useful in improving the current design of the planned American life support equipment; evaluating the ongoing Russian life support technology development activities to determine areas of potential long-term application to the U.S. space station; and utilizing the expertise of their space station life support systems to evaluate the benefits to the current U.S. space station program which included the integration of the Russian Mir-1 designs with the U.S. designs to support a crew of six.

Evaluation of a participatory ergonomics intervention in small commercial construction firms.

PubMed

Dale, Ann Marie; Jaegers, Lisa; Welch, Laura; Gardner, Bethany T; Buchholz, Bryan; Weaver, Nancy; Evanoff, Bradley A

2016-06-01

Work-related musculoskeletal disorders (WMSD) among construction workers remain high. Participatory ergonomics (PE) interventions that engage workers and employers in reducing work injury risks have shown mixed results. Eight-six workers from seven contractors participated in a PE program. A logic model guided the process evaluation and summative evaluation of short-term and intermediate impacts and long-term outcomes from surveys and field records. Process measures showed good delivery of training, high worker engagement, and low contractor participation. Workers' knowledge improved and workers reported changes to work practices and tools used; contractor provision of appropriate equipment was low (33%). No changes were seen in symptoms or reported physical effort. The PE program produced many worker-identified ergonomic solutions, but lacked needed support from contractors. Future interventions should engage higher levels of the construction organizational system to improve contractor involvement for reducing WMSD. Am. J. Ind. Med. 59:465-475, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Environmental control and life support system: Analysis of STS-1

NASA Technical Reports Server (NTRS)

Steines, G.

1980-01-01

The capability of the orbiter environmental control and life support system (ECLSS) to support vehicle cooling requirements in the event of cabin pressure reduction to 9 psia was evaluated, using the Orbiter versions of the shuttle environmental consumbles usage requirement evaluation (SECURE) program, and using heat load input data developed by the spacecraft electrical power simulator (SEPS) program. The SECURE model used in the analysis, the timeline and ECLSS configuration used in formulating the analysis, and the results of the analysis are presented. The conclusion which may be drawn drom these results. is summarized. There are no significant thermal problems with the proposed mission. There are, however, several procedures which could be optimized for better performance: setting the cabin HX air bypass and the interchanger water bypass to the zero flow position is of questionable efficacy; the cabin air pressure monitoring procedure should be re-evaluated; and the degree of equipment power down specified for this analysis and no problems were noted.

47 CFR 76.1206 - Equipment sale or lease charge subsidy prohibition.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Equipment sale or lease charge subsidy prohibition. 76.1206 Section 76.1206 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Devices § 76.1206 Equipment sale or lease charge subsidy prohibition. Multichannel video programming...

76 FR 26641 - Relay Services for Deaf-Blind Individuals

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-09

... this document, the Commission adopts rules to establish the National Deaf-Blind Equipment Distribution... premises equipment (CPE) to low- income individuals who are deaf-blind. For these purposes, this new... (TRS) Fund. The equipment distributed under the NDBEDP pilot program will make telecommunications...

Factors affecting the corrosivity of pulping liquors

NASA Astrophysics Data System (ADS)

Hazlewood, Patrick Evan

Increased equipment failures and the resultant increase in unplanned downtime as the result of process optimization programs continue to plague pulp mills. The failures are a result of a lack of understanding of corrosion in the different pulping liquors, specifically the parameters responsible for its adjustment such as the role and identification of inorganic and organic species. The current work investigates the role of inorganic species, namely sodium hydroxide and sodium sulfide, on liquor corrosivity at a range of process conditions beyond those currently experienced in literature. The role of sulfur species, in the activation of corrosion and the ability of hydroxide to passivate carbon steel A516-Gr70, is evaluated with gravimetric and electrochemical methods. The impact of wood chip weathering on process corrosion was also evaluated. Results were used to identify black liquor components, depending on the wood species, which play a significant role in the activation and inhibition of corrosion for carbon steel A516-Gr70 process equipment. Further, the effect of black liquor oxidation on liquor corrosivity was evaluated. Corrosion and stress corrosion cracking performance of selected materials provided information on classes of materials that may be reliably used in aggressive pulping environments.

Medicare program; competitive acquisition for certain durable medical equipment, prosthetics, orthotics, and supplies (DMEPOS) and other issues. Final rule.

PubMed

2007-04-10

This final rule establishes competitive bidding programs for certain Medicare Part B covered items of durable medical equipment, prosthetics, orthotics, and supplies (DMEPOS) throughout the United States in accordance with sections 1847(a) and (b) of the Social Security Act. These competitive bidding programs, which will be phased in over several years, utilize bids submitted by DMEPOS suppliers to establish applicable payment amounts under Medicare Part B.

Commercial equipment loads: End-Use Load and Consumer Assessment Program (ELCAP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pratt, R.G.; Williamson, M.A.; Richman, E.E.

1990-07-01

The Office of Energy Resources of the Bonneville Power Administration is generally responsible for the agency's power and conservation resource planning. As associated responsibility which supports a variety of office functions is the analysis of historical trends in and determinants of energy consumption. The Office of Energy Resources' End-Use Research Section operates a comprehensive data collection program to provide pertinent information to support demand-side planning, load forecasting, and demand-side program development and delivery. Part of this on-going program is known as the End-Use Load and Consumer Assessment Program (ELCAP), an effort designed to collect electricity usage data through direct monitoringmore » of end-use loads in buildings. This program is conducted for Bonneville by the Pacific Northwest Laboratory. This report provides detailed information on electricity consumption of miscellaneous equipment from the commercial portion of ELCAP. Miscellaneous equipment includes all commercial end-uses except heating, ventilating, air conditioning, and central lighting systems. Some examples of end-uses covered in this report are office equipment, computers, task lighting, refrigeration, and food preparation. Electricity consumption estimates, in kilowatt-hours per square food per year, are provided for each end-use by building type. The following types of buildings are covered: office, retail, restaurant, grocery, warehouse, school, university, and hotel/motel. 6 refs., 35 figs., 12 tabs.« less

Using EQUIP for Educators to Prevent Peer Victimization in Secondary School

ERIC Educational Resources Information Center

van der Meulen, Kevin; Granizo, Laura; del Barrio, Cristina

2010-01-01

Peer victimization has received much attention from researchers and educators over the last decade, since it is a problem that affects children and adolescents. As more time-extensive programs do not seem to be used in schools, in this article the "EQUIP" program for "Educators" is proposed as an instrument for the prevention…

9 CFR 592.95 - Facilities and equipment to be furnished for use of inspection program personnel in performing...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Facilities and equipment to be furnished for use of inspection program personnel in performing service. 592.95 Section 592.95 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE EGG PRODUCTS INSPECTION...

Policy, environment, and worksite fitness program participation among financial enterprise employees in Taiwan.

PubMed

Huang, Sheu-Jen; Hung, Wen-Chi

2016-06-01

This study explored the intertwined effects between the policies and regulations of the companies and personal background on participation in the physical fitness programs and leisure-time activities in financial enterprises. A total of 823 employees were selected as the sample with the multilevel stratification random-sampling technique. The response rate was 52.0%. Data were analyzed with descriptive statistics and hierarchical linear logistic regression. Thirty-two percent and 39% of the employees participated in the physical fitness programs and leisure-time activities, respectively. The factors affecting participation were categorized into intrapersonal factors, interpersonal processes, and primary groups, as well as institutional factors. In the interpersonal processes and primary groups level, higher family social support, more equipment in health promotion was associated with more participation in the programs. With the influence from the institutional level, it was found that health promotion policy amplified the relationship between employees' age and participation, but attenuated the relationship between education level and participation. Health promotion equipment in the institutes attenuated the relationship between colleague social support, family social support, and education level with program participation. Physical activity equipment in the community attenuated the relationship between family social support and program participation. The influential factors of social support and worksite environment could predict the employees' participation in the physical fitness programs and leisure-time physical activities. Health promotion policy and equipment attenuated the negative effects of nonparticipation as well as amplified the positive effects of participation.

Key Performance Indicators in the Evaluation of the Quality of Radiation Safety Programs.

PubMed

Schultz, Cheryl Culver; Shaffer, Sheila; Fink-Bennett, Darlene; Winokur, Kay

2016-08-01

Beaumont is a multiple hospital health care system with a centralized radiation safety department. The health system operates under a broad scope Nuclear Regulatory Commission license but also maintains several other limited use NRC licenses in off-site facilities and clinics. The hospital-based program is expansive including diagnostic radiology and nuclear medicine (molecular imaging), interventional radiology, a comprehensive cardiovascular program, multiple forms of radiation therapy (low dose rate brachytherapy, high dose rate brachytherapy, external beam radiotherapy, and gamma knife), and the Research Institute (including basic bench top, human and animal). Each year, in the annual report, data is analyzed and then tracked and trended. While any summary report will, by nature, include items such as the number of pieces of equipment, inspections performed, staff monitored and educated and other similar parameters, not all include an objective review of the quality and effectiveness of the program. Through objective numerical data Beaumont adopted seven key performance indicators. The assertion made is that key performance indicators can be used to establish benchmarks for evaluation and comparison of the effectiveness and quality of radiation safety programs. Based on over a decade of data collection, and adoption of key performance indicators, this paper demonstrates one way to establish objective benchmarking for radiation safety programs in the health care environment.

Cost analysis of large-scale implementation of the 'Helping Babies Breathe' newborn resuscitation-training program in Tanzania.

PubMed

Chaudhury, Sumona; Arlington, Lauren; Brenan, Shelby; Kairuki, Allan Kaijunga; Meda, Amunga Robson; Isangula, Kahabi G; Mponzi, Victor; Bishanga, Dunstan; Thomas, Erica; Msemo, Georgina; Azayo, Mary; Molinier, Alice; Nelson, Brett D

2016-12-01

Helping Babies Breathe (HBB) has become the gold standard globally for training birth-attendants in neonatal resuscitation in low-resource settings in efforts to reduce early newborn asphyxia and mortality. The purpose of this study was to do a first-ever activity-based cost-analysis of at-scale HBB program implementation and initial follow-up in a large region of Tanzania and evaluate costs of national scale-up as one component of a multi-method external evaluation of the implementation of HBB at scale in Tanzania. We used activity-based costing to examine budget expense data during the two-month implementation and follow-up of HBB in one of the target regions. Activity-cost centers included administrative, initial training (including resuscitation equipment), and follow-up training expenses. Sensitivity analysis was utilized to project cost scenarios incurred to achieve countrywide expansion of the program across all mainland regions of Tanzania and to model costs of program maintenance over one and five years following initiation. Total costs for the Mbeya Region were $202,240, with the highest proportion due to initial training and equipment (45.2%), followed by central program administration (37.2%), and follow-up visits (17.6%). Within Mbeya, 49 training sessions were undertaken, involving the training of 1,341 health providers from 336 health facilities in eight districts. To similarly expand the HBB program across the 25 regions of mainland Tanzania, the total economic cost is projected to be around $4,000,000 (around $600 per facility). Following sensitivity analyses, the estimated total for all Tanzania initial rollout lies between $2,934,793 to $4,309,595. In order to maintain the program nationally under the current model, it is estimated it would cost $2,019,115 for a further one year and $5,640,794 for a further five years of ongoing program support. HBB implementation is a relatively low-cost intervention with potential for high impact on perinatal mortality in resource-poor settings. It is shown here that nationwide expansion of this program across the range of health provision levels and regions of Tanzania would be feasible. This study provides policymakers and investors with the relevant cost-estimation for national rollout of this potentially neonatal life-saving intervention.

47 CFR 74.13 - Equipment tests.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Equipment tests. 74.13 Section 74.13 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES EXPERIMENTAL RADIO, AUXILIARY, SPECIAL BROADCAST AND OTHER PROGRAM DISTRIBUTIONAL SERVICES General; Rules Applicable to All Services in Part 74 § 74.13 Equipment tests. (...

40 CFR 82.162 - Certification by owners of recovery and recycling equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... and recycling equipment. 82.162 Section 82.162 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.162 Certification by owners of recovery and recycling equipment. (a) No later than August 12...

40 CFR 82.162 - Certification by owners of recovery and recycling equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... and recycling equipment. 82.162 Section 82.162 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.162 Certification by owners of recovery and recycling equipment. (a) No later than August 12...

40 CFR 82.162 - Certification by owners of recovery and recycling equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... and recycling equipment. 82.162 Section 82.162 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.162 Certification by owners of recovery and recycling equipment. (a) No later than August 12...

40 CFR 82.162 - Certification by owners of recovery and recycling equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and recycling equipment. 82.162 Section 82.162 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.162 Certification by owners of recovery and recycling equipment. (a) No later than August 12...

40 CFR 82.162 - Certification by owners of recovery and recycling equipment.

Code of Federal Regulations, 2012 CFR

2012-07-01

... and recycling equipment. 82.162 Section 82.162 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling and Emissions Reduction § 82.162 Certification by owners of recovery and recycling equipment. (a) No later than August 12...

15 CFR 14.34 - Equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Equipment. 14.34 Section 14.34 Commerce and Foreign Trade Office of the Secretary of Commerce UNIFORM ADMINISTRATIVE REQUIREMENTS FOR... shall be treated as program income. (e) When acquiring replacement equipment, the recipient may use the...

Summaries of FY 1993 geosciences research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-12-01

The Department of Energy supports research in the geosciences in order to provide a sound foundation of fundamental knowledge in those areas of the geosciences that are germane to the DOE`s many missions. The Geosciences Research Program is supported by the Office of Energy Research. The participants in this program include DOE laboratories, academic institutions, and other governmental agencies. These activities are formalized by a contract or grant between the DOE and the organization performing the work, providing funds for salaries, equipment, research materials, and overhead. The summaries in this document, prepared by the investigators, describe the scope of themore » individual programs. The Geosciences Research Program includes research in geophysics, geochemistry, resource evaluation, solar-terrestrial interactions, and their subdivisions including earth dynamics, properties of earth materials, rock mechanics, underground imaging, rock-fluid interactions, continental scientific drilling, geochemical transport, solar-atmospheric physics, and modeling, with emphasis on the interdisciplinary areas.« less

Failure Analysis at the Kennedy Space Center

NASA Technical Reports Server (NTRS)

Salazar, Victoria L.; Wright, M. Clara

2010-01-01

History has shown that failures occur in every engineering endeavor, and what we learn from those failures contributes to the knowledge base to safely complete future missions. The necessity of failure analysis is at its apex at the end of one aged program and at the beginning of a new and untested program. The information that we gain through failure analysis corrects the deficiencies in the current vehicle to make the next generation of vehicles more efficient and safe. The Failure Analysis and Materials Evaluation Branch in the Materials Science Division at the Kennedy Space Center performs metallurgical, mechanical, electrical, and non-metallic materials failure analyses and accident investigations on both flight hardware and ground support equipment for the Space Shuttle, International Space Station, Constellation, and Launch Services Programs. This paper will explore a variety of failure case studies at the Kennedy Space Center and the lessons learned that can be applied in future programs.

Shuttle communication and tracking systems signal design and interface compatibility analysis

NASA Technical Reports Server (NTRS)

1986-01-01

Various options for the Dedicated Payload Communication Link (DPCL) were evaluated. Specific subjects addressed include: payload to DPCL power transfer in the proximity of the payload, DPCL antenna pointing considerations, and DPCL transceiver implementations which can be mounted on the deployed antenna boom. Additional analysis of the Space Telescope performance was conducted. The feasibility of using the Global Positioning System (GPS) for attitude determination and control for large spacecraft was examined. The objective of the Shuttle Orbiter Radar Test and Evaluation (SORTE) program was to quantify the Ku-band radar tracking accuracy using White Sands Missile Range (WSMR) radar and optical tracking equipment, with helicopter and balloon targets.

Evaluating science return in space exploration initiative architectures

NASA Technical Reports Server (NTRS)

Budden, Nancy Ann; Spudis, Paul D.

1993-01-01

Science is an important aspect of the Space Exploration Initiative, a program to explore the Moon and Mars with people and machines. Different SEI mission architectures are evaluated on the basis of three variables: access (to the planet's surface), capability (including number of crew, equipment, and supporting infrastructure), and time (being the total number of man-hours available for scientific activities). This technique allows us to estimate the scientific return to be expected from different architectures and from different implementations of the same architecture. Our methodology allows us to maximize the scientific return from the initiative by illuminating the different emphases and returns that result from the alternative architectural decisions.

Advanced technologies for maintenance of electrical systems and equipment at the Savannah River Site Defense Waste Processing Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Husler, R.O.; Weir, T.J.

1991-01-01

An enhanced maintenance program is being established to characterize and monitor cables, components, and process response at the Savannah River Site, Defense Waste Processing Facility. This facility was designed and constructed to immobilize the radioactive waste currently stored in underground storage tanks and is expected to begin operation in 1993. The plant is initiating the program to baseline and monitor instrument and control (I C) and electrical equipment, remote process equipment, embedded instrument and control cables, and in-cell jumper cables used in the facility. This program is based on the electronic characterization and diagnostic (ECAD) system which was modified tomore » include process response analysis and to meet rigid Department of Energy equipment requirements. The system consists of computer-automated, state-of-the-art electronics. The data that are gathered are stored in a computerized database for analysis, trending, and troubleshooting. It is anticipated that the data which are gathered and trended will aid in life extension for the facility.« less

Advanced technologies for maintenance of electrical systems and equipment at the Savannah River Site Defense Waste Processing Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Husler, R.O.; Weir, T.J.

1991-12-31

An enhanced maintenance program is being established to characterize and monitor cables, components, and process response at the Savannah River Site, Defense Waste Processing Facility. This facility was designed and constructed to immobilize the radioactive waste currently stored in underground storage tanks and is expected to begin operation in 1993. The plant is initiating the program to baseline and monitor instrument and control (I&C) and electrical equipment, remote process equipment, embedded instrument and control cables, and in-cell jumper cables used in the facility. This program is based on the electronic characterization and diagnostic (ECAD) system which was modified to includemore » process response analysis and to meet rigid Department of Energy equipment requirements. The system consists of computer-automated, state-of-the-art electronics. The data that are gathered are stored in a computerized database for analysis, trending, and troubleshooting. It is anticipated that the data which are gathered and trended will aid in life extension for the facility.« less

From Desire to Data: How JLab's Experimental Program Evolved Part 2: The Painstaking Transition to Concrete Plans, Mid-1980s to 1990

NASA Astrophysics Data System (ADS)

Westfall, Catherine

2018-03-01

This is the second in a three-part article describing the development of the Thomas Jefferson National Accelerator Facility's experimental program, from the first dreams of incisive electromagnetic probes into the structure of the nucleus through the era in which equipment was designed and constructed and a program crafted so that the long-desired experiments could begin. These developments unfolded against the backdrop of the rise of the more bureaucratic New Big Science and the intellectual tumult that grew from increasing understanding and interest in quark-level physics. Part 2, presented here, focuses on the period from 1986 to 1990. During this period of revolutionary change, laboratory personnel, potential users, and DOE officials labored to proceed from the 1986 laboratory design report, which included detailed accelerator plans and very preliminary experimental equipment sketches, to an approved 1990 experimental equipment conceptual design report, which provided designs complete enough for the onset of experimental equipment construction.

Italy-Japan international project-based learning for developing human resources using design of welfare equipment as a subject.

PubMed

Hanafusa, A; Komeda, T; Ito, K; Zobel, P Beomonte

2015-08-01

Project-based learning (PBL) is effective for developing human resources of young students. The design of welfare equipment, such as wheelchairs and gait assistive devices, is taken as the subject in this study because these devices must be fit to their environment, users, and method of use; students must consider the circumstances of each country concerned. The program commenced in 2012 at L'Aquila, Italy, and the Shibaura Institute of Technology, Japan and has been continuing for three years. Students were divided into four groups and discussions were held on how to adapt the equipment to the user and environment. After discussion, they designed and simulated a model of the equipment using CAD. Finally, they presented their designs to each other. Through the program, students had fruitful discussions, exchanged ideas from different cultures, and learned from each other. Furthermore, friendships among the students were nurtured. It is believed that the objective of the program was satisfactorily accomplished.

Cooled High-temperature Radial Turbine Program 2

NASA Technical Reports Server (NTRS)

Snyder, Philip H.

1991-01-01

The objective of this program was the design and fabrication of a air-cooled high-temperature radial turbine (HTRT) intended for experimental evaluation in a warm turbine test facility at the LeRC. The rotor and vane were designed to be tested as a scaled version (rotor diameter of 14.4 inches diameter) of a 8.021 inch diameter rotor designed to be capable of operating with a rotor inlet temperature (RIT) of 2300 F, a nominal mass flow of 4.56 lbm/sec, a work level of equal or greater than 187 Btu/lbm, and efficiency of 86 percent or greater. The rotor was also evaluated to determine it's feasibility to operate at 2500 F RIT. The rotor design conformed to the rotor blade flow path specified by NASA for compatibility with their test equipment. Fabrication was accomplished on three rotors, a bladeless rotor, a solid rotor, and an air-cooled rotor.

[Evaluation of prerequisites programs for a HACCP plan for frozen sardine plant].

PubMed

Rosas, Patricia; Reyes, Genara

2008-06-01

Good manufacturing practices (GMP) and sanitation standard operating procedures (SSOP) are prerequisites programs for the application of the Hazard Analysis and Critical Control Point (HACCP) system as a food safety approach during processing. The aim of this study was to evaluate GMP/SSOP prerequisites in processing line of frozen whole sardine (Sardinella aurita). The GMP compliance was verified according to a standard procedure of the Ministry for the Health of Venezuela, and the SSOP were assessed according to a checklist proposed by the FDA. GMP and SSOP were evaluated following a demerit-based approach. A percentage value was calculated and referred to as sanitary effectiveness. Results indicated that the plant had a good level of compliance with GMP from assessment of buildings and facilities, equipment and tools, hygienic requisites of the production, assurance of the hygiene quality, storage and transportation, and the percentage of sanitary effectiveness was 84%. The level of compliance for SSOP was 53,12% with demerits found in all assessed aspects consisting of inexistent guidelines, lack of control in the sanitary plan and lack of leadership in applying corrective actions. Thus, an improvement in the plant sanitation program was designed targeting SSOP.

Air National Guard Financial Reports on the National Guard and Reserve Equipment Appropriation.

DTIC Science & Technology

1997-12-16

consolidated financial statements for FY 1996 and each succeeding year. In 1981, Congress established the National Guard and Reserve Equipment Appropriation to provide the equipment needed to maintain the readiness of the National Guard and Reserve units. In FY 1996, the Air National Guard received a total of $260.4 million for National Guard and Reserve Equipment programs, The Defense Finance

Kennedy Space Center: Constellation Program Electrical Ground Support Equipment Research and Development

NASA Technical Reports Server (NTRS)

McCoy, Keegan

2010-01-01

The Kennedy Space Center (KSC) is NASA's spaceport, launching rockets into space and leading important human spaceflight research. This spring semester, I worked at KSC on Constellation Program electrical ground support equipment through NASA's Undergraduate Student Research Program (USRP). This report includes a discussion of NASA, KSC, and my individual research project. An analysis of Penn State's preparation of me for an internship and my overall impressions of the Penn State and NASA internship experience conclude the report.

"India Population Projects" in Karnataka.

PubMed

Reddy, P H; Badari, V S

1991-12-01

An overview, objectives, implementation, and research and evaluation studies of 2 India Population Projects in Karnataka are presented. The India Population Project I (IPP-I) was conducted in Karnataka and Uttar Pradesh. India Population Project III (IPP-III) took place between 1984-92 in 6 districts of Karnataka: Belgaum, Bijapur, Dharwad, Bidar, Gulbarga, and Raichur, and 4 districts in Kerala. The 6 districts in Karnataka accounted for 36% (13.2 million) of the total national population. The project cost was Rs. 713.1 million which was shared by the World Bank, and the Indian national and regional government. Due to poor past performance, these projects were undertaken to improve health and family welfare status. Specific project objectives are outlined. IPP-I included an urban component, and optimal Government of India program, and an intensive rural initiative. The urban program aimed to improved pre- and postnatal services and facilities, and the family planning (FP) in Bangalore city. The rural program was primarily to provide auxiliary nurse-midwives and hospitals and clinics, and also supplemental feeding program for pregnant and nursing mothers and children up to 2 years. The government program provided FP staff and facilities. IPP-I had 3 units to oversee building construction, to recruit staff and provide supplies and equipment, and to establish a Population Center. IPP-III was concerned with service delivery; information, education, and communication efforts (IEC) and population education; research and evaluation; and project management. Both projects contributed significantly to improving the infrastructure. A brief account of the types and kinds of studies undertaken is given. Studies were grouped into longitudinal studies of fertility, mortality, and FP; management information and evaluation systems for health and family welfare programs; experimental strategies; and other studies. Research and evaluation studies in IPP-III encompassed studies in gaps in knowledge, skills, and practice of health and FP personnel; baseline and endline surveys; and operational evaluation of the management information and evaluation system; factors affecting primary health care in Gulbarga district; evaluation of radio health lessons and the impact of the Kalyana Matha Program; and studies of vaccination and child survival and maternal mortality. Training programs were also undertaken.

Planting, Growing, Caring.

ERIC Educational Resources Information Center

Carrick, James

Six units of instruction are provided in this manual designed for deaf students enrolled in an ornamental horticulture program. Unit 1 contains eight lessons (pictures and names) on tool and equipment identification (e.g., cutting and pruning tools, lawn and garden equipment, and power equipment). Unit 2 provides ten lessons on the care of tools…